WorldWideScience

Sample records for control in manufacturing

  1. Robust Manufacturing Control

    CERN Document Server

    2013-01-01

    This contributed volume collects research papers, presented at the CIRP Sponsored Conference Robust Manufacturing Control: Innovative and Interdisciplinary Approaches for Global Networks (RoMaC 2012, Jacobs University, Bremen, Germany, June 18th-20th 2012). These research papers present the latest developments and new ideas focusing on robust manufacturing control for global networks. Today, Global Production Networks (i.e. the nexus of interconnected material and information flows through which products and services are manufactured, assembled and distributed) are confronted with and expected to adapt to: sudden and unpredictable large-scale changes of important parameters which are occurring more and more frequently, event propagation in networks with high degree of interconnectivity which leads to unforeseen fluctuations, and non-equilibrium states which increasingly characterize daily business. These multi-scale changes deeply influence logistic target achievement and call for robust planning and control ...

  2. Control systems engineering in continuous pharmaceutical manufacturing. May 20-21, 2014 Continuous Manufacturing Symposium.

    Science.gov (United States)

    Myerson, Allan S; Krumme, Markus; Nasr, Moheb; Thomas, Hayden; Braatz, Richard D

    2015-03-01

    This white paper provides a perspective of the challenges, research needs, and future directions for control systems engineering in continuous pharmaceutical processing. The main motivation for writing this paper is to facilitate the development and deployment of control systems technologies so as to ensure quality of the drug product. Although the main focus is on small-molecule pharmaceutical products, most of the same statements apply to biological drug products. An introduction to continuous manufacturing and control systems is followed by a discussion of the current status and technical needs in process monitoring and control, systems integration, and risk analysis. Some key points are that: (1) the desired objective in continuous manufacturing should be the satisfaction of all critical quality attributes (CQAs), not for all variables to operate at steady-state values; (2) the design of start-up and shutdown procedures can significantly affect the economic operation of a continuous manufacturing process; (3) the traceability of material as it moves through the manufacturing facility is an important consideration that can at least in part be addressed using residence time distributions; and (4) the control systems technologies must assure quality in the presence of disturbances, dynamics, uncertainties, nonlinearities, and constraints. Direct measurement, first-principles and empirical model-based predictions, and design space approaches are described for ensuring that CQA specifications are met. Ways are discussed for universities, regulatory bodies, and industry to facilitate working around or through barriers to the development of control systems engineering technologies for continuous drug manufacturing. Industry and regulatory bodies should work with federal agencies to create federal funding mechanisms to attract faculty to this area. Universities should hire faculty interested in developing first-principles models and control systems technologies for

  3. Microeconomics of process control in semiconductor manufacturing

    Science.gov (United States)

    Monahan, Kevin M.

    2003-06-01

    Process window control enables accelerated design-rule shrinks for both logic and memory manufacturers, but simple microeconomic models that directly link the effects of process window control to maximum profitability are rare. In this work, we derive these links using a simplified model for the maximum rate of profit generated by the semiconductor manufacturing process. We show that the ability of process window control to achieve these economic objectives may be limited by variability in the larger manufacturing context, including measurement delays and process variation at the lot, wafer, x-wafer, x-field, and x-chip levels. We conclude that x-wafer and x-field CD control strategies will be critical enablers of density, performance and optimum profitability at the 90 and 65nm technology nodes. These analyses correlate well with actual factory data and often identify millions of dollars in potential incremental revenue and cost savings. As an example, we show that a scatterometry-based CD Process Window Monitor is an economically justified, enabling technology for the 65nm node.

  4. Fundamentals of semiconductor manufacturing and process control

    CERN Document Server

    May, Gary S

    2006-01-01

    A practical guide to semiconductor manufacturing from process control to yield modeling and experimental design Fundamentals of Semiconductor Manufacturing and Process Control covers all issues involved in manufacturing microelectronic devices and circuits, including fabrication sequences, process control, experimental design, process modeling, yield modeling, and CIM/CAM systems. Readers are introduced to both the theory and practice of all basic manufacturing concepts. Following an overview of manufacturing and technology, the text explores process monitoring methods, including those that focus on product wafers and those that focus on the equipment used to produce wafers. Next, the text sets forth some fundamentals of statistics and yield modeling, which set the foundation for a detailed discussion of how statistical process control is used to analyze quality and improve yields. The discussion of statistical experimental design offers readers a powerful approach for systematically varying controllable p...

  5. A system approach to controlling semiconductor manufacturing operations

    OpenAIRE

    Σταυράκης, Γιώργος Δ.

    1987-01-01

    Semicoductor manufacturers, faced with stiffening competition in both product cost and quality, require improved utilization of their development and manufacturing resources. Manufacturing philosophy must be changed, from focusing on short term results, to support continuous improvements in both output and quality. Such improvements demand better information management to monitor and control the manufacturing process. From these considerations, a process control methodology was develope...

  6. Regulatory control of fuel design and manufacturing

    International Nuclear Information System (INIS)

    1994-01-01

    The regulatory control of the design and manufacturing of the nuclear fuel and of the control rods aims to ensure conformance to set requirements during normal operating conditions, anticipated operational transients and postulated accident conditions. The regulatory control of design, manufacturing, receiving inspections and the start of operation of the nuclear fuel are specified in the guide. The regulatory control procedure also applies to the control rods and the shield elements

  7. Handbook of Manufacturing Control Fundamentals, description, configuration

    CERN Document Server

    Lödding, Hermann

    2013-01-01

    This first-time English publication of one of Germany’s leading manufacturing control handbooks provides a comprehensive overview of the state of the art, with detailed and easy to understand descriptions of numerous control techniques from Kanban to CONWIP to Backlog Control. Based on the proven funnel model and written for the industry, this book clearly illustrates how companies can use manufacturing control to effectively improve on-time delivery, reduce inventories and cut down throughput times. “This book distinguishes itself with its convincing systematic approach based on thorough international research. Its clear presentation and direct applicability for analysing and configuring the manufacturing control make this handbook an outstanding and unique publication on PPC.” Hans-Peter Wiendahl “The field of manufacturing control is very convincingly reviewed and presented from a theoretical and methodological perspective. Both researchers as well as practitioners will profit from it.” Peter N...

  8. 21 CFR 1307.13 - Incidental manufacture of controlled substances.

    Science.gov (United States)

    2010-04-01

    ..., manufactures a controlled substance as a result of the manufacture of a controlled substance or basic class of controlled substance for which he is registered and has been issued an individual manufacturing quota pursuant to part 1303 of this chapter (if such substance or class is listed in Schedule I or II) shall be...

  9. Manufacturing systems considered as time domain control systems : receding horizon control and observers

    NARCIS (Netherlands)

    Roset, B.J.P.

    2007-01-01

    This thesis considers manufacturing systems and model-based controller design, as well as their combinations. The objective of a manufacturing system is to create products from a selected group of raw materials and semifinished goods. In the field of manufacturing systems control is an important

  10. 76 FR 39127 - Manufacturer of Controlled Substances; Notice of Application

    Science.gov (United States)

    2011-07-05

    ... Administration (DEA) to be registered as a bulk manufacturer of Remifentanil (9739) the basic class of controlled substance in schedule II. The company plans to utilize this facility to manufacture small quantities of the... primary manufacturing facility in West Deptford, New Jersey. The controlled substances manufactured in...

  11. 77 FR 5849 - Manufacturer of Controlled Substances; Notice of Registration

    Science.gov (United States)

    2012-02-06

    ... (DEA) to be registered as a bulk manufacturer of Remifentanil (9739), the basic class of controlled substance in schedule II. The company plans to utilize this facility to manufacture small quantities of the... manufacturing facility in West Deptford, New Jersey. The controlled substances manufactured in bulk at this...

  12. 49 CFR 534.5 - Manufacturers within control relationships.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 6 2010-10-01 2010-10-01 false Manufacturers within control relationships. 534.5... IN THE CONTEXT OF CHANGES IN CORPORATE RELATIONSHIPS § 534.5 Manufacturers within control relationships. (a) If a civil penalty arises out of a fuel economy shortfall incurred by a group of...

  13. Manufacturing and application of micro computer for control

    International Nuclear Information System (INIS)

    Park, Seung Man; Heo, Gyeong; Yun, Jun Young

    1990-05-01

    This book deals with machine code and assembly program for micro computer. It composed of 20 chapters, which are micro computer system, practice of a storage cell, manufacturing 1 of micro computer, manufacturing 2 of micro computer, manufacturing of micro computer AID-80A, making of machine language, interface like Z80-PIO and 8255A(PPI), counter and timer interface, exercise of basic command, arithmetic operation, arrangement operation, an indicator control, music playing, detection of input of PIO. control of LED of PIO, PIO mode, CTC control by micro computer, SIO control by micro computer and application by micro computer.

  14. 76 FR 81979 - Manufacturer of Controlled Substances; Notice of Application

    Science.gov (United States)

    2011-12-29

    ...), the company presently manufactures a small amount of this controlled substance in bulk solely to conduct manufacturing internal process development. It is the company's intention that, when the... (1105) only, the company manufactures these controlled substances in bulk solely for distribution within...

  15. Composite materials pipings: selection of basic materials and manufacturing process, quality control during manufacture

    International Nuclear Information System (INIS)

    Pays, M.F.

    1997-01-01

    The purpose of the paper is to present a summary of the knowledge acquired at the R and D on resins used as composite matrix, the resistance to hydrolysis and mechanical strength of pipings made from these materials, and on quality control during manufacture. The initial targets concerning the material selection, industrial manufacturing and quality control procedures are presented. The paper describes the results obtained concerning the investigation of the damage produced by hydrolysis in polyesters, vinyl esters and epoxides, the influence of temperature, reinforcement and the mechanical characterization of the tubing manufacturing. The performances of the nondestructive testings (radiography, ultrasonic controls, differential interferometry and infrared thermography) used are also reported. The paper ends with a further research and testings programme. (author)

  16. Research of user access control for networked manufacturing system

    Institute of Scientific and Technical Information of China (English)

    ZHENG Xiao-lin; LEI Yu; CHEN De-ren

    2006-01-01

    An integrated user access control method was proposed to address the issues of security and management in networked manufacturing systems (NMS).Based on the analysis of the security issues in networked manufacturing system,an integrated user access control method composed of role-based access control (RBAC),task-based access control (TBAC),relationship-driven access control (RDAC)and coalition-based access control (CBAC) was proposed,including the hierarchical user relationship model,the reference model and the process model.The elements and their relationships were defined,and the expressions of constraints authorization were given.The extensible access control markup language (XACML) was used to implement this method.This method was used in the networked manufacturing system in the Shaoxing spinning region of China.The results show that the integrated user access control method can reduce the costs of system security maintenance and management.

  17. Dimensional metrology for process and part quality control in micro manufacturing

    DEFF Research Database (Denmark)

    Hansen, Hans Nørgaard; Tosello, Guido; Gasparin, Stefania

    2011-01-01

    dimensions are scaled down and geometrical complexity of objects is increased, the available measurement technologies appear not sufficient. New solutions for measuring principles and instrumentation, tolerancing rules and procedures as well as traceability and calibration are necessary if micro......Micro manufacturing has gained interest over the last decade as the demand for micro mechanical components has increased. The need for dimensional metrology at micro scale is evident both in terms of quality assurance of components and products and in terms of process control. As critical...... manufacturing is to develop into industrial manufacturing solutions. In this paper the application of dimensional precision metrology to both component and process quality control will be demonstrated. The parts investigated are micro injection moulded polymer parts, typical for the field of micro manufacturing....

  18. The Application of Time-Delay Dependent H∞ Control Model in Manufacturing Decision Optimization

    Directory of Open Access Journals (Sweden)

    Haifeng Guo

    2015-01-01

    Full Text Available This paper uses a time-delay dependent H∞ control model to analyze the effect of manufacturing decisions on the process of transmission from resources to capability. We establish a theoretical framework of manufacturing management process based on three terms: resource, manufacturing decision, and capability. Then we build a time-delay H∞ robust control model to analyze the robustness of manufacturing management. With the state feedback controller between manufacturing resources and decision, we find that there is an optimal decision to adjust the process of transmission from resources to capability under uncertain environment. Finally, we provide an example to prove the robustness of this model.

  19. Controlling flow time delays in flexible manufacturing cells

    NARCIS (Netherlands)

    Slomp, J.; Caprihan, R.; Bokhorst, J. A. C.

    2009-01-01

    Flow time delays in Flexible Manufacturing Cells (FMCs) are caused by transport and clamping/reclamping activities. This paper shows how dynamic scheduling parameters may control the flow times of jobs and the available task windows for flow time delays.

  20. Grain Structure Control of Additively Manufactured Metallic Materials

    Directory of Open Access Journals (Sweden)

    Fuyao Yan

    2017-11-01

    Full Text Available Grain structure control is challenging for metal additive manufacturing (AM. Grain structure optimization requires the control of grain morphology with grain size refinement, which can improve the mechanical properties of additive manufactured components. This work summarizes methods to promote fine equiaxed grains in both the additive manufacturing process and subsequent heat treatment. Influences of temperature gradient, solidification velocity and alloy composition on grain morphology are discussed. Equiaxed solidification is greatly promoted by introducing a high density of heterogeneous nucleation sites via powder rate control in the direct energy deposition (DED technique or powder surface treatment for powder-bed techniques. Grain growth/coarsening during post-processing heat treatment can be restricted by presence of nano-scale oxide particles formed in-situ during AM. Grain refinement of martensitic steels can also be achieved by cyclic austenitizing in post-processing heat treatment. Evidently, new alloy powder design is another sustainable method enhancing the capability of AM for high-performance components with desirable microstructures.

  1. 76 FR 21917 - Manufacturer of Controlled Substances; Notice of Registration

    Science.gov (United States)

    2011-04-19

    ... manufacturer of the following basic classes of controlled substances: Drug Schedule Marihuana (7360) I Tetrahydrocannabinols (7370) I The company plans to manufacture small quantities of marihuana derivatives for research purposes. In reference to drug code 7360 (Marihuana), the company plans to bulk manufacture cannabidiol. In...

  2. Additive Manufacturing: Multi Material Processing and Part Quality Control

    DEFF Research Database (Denmark)

    Pedersen, David Bue

    This Ph.D dissertation,ffAdditive Manufacturing: Multi Material Processing and Part Quality Controlff, deal with Additive Manufacturing technologies which is a common name for a series of processes that are recognized by being computer controlled, highly automated, and manufacture objects...... by a layered deposition of material. Two areas of particular interest is addressed. They are rooted in two very different areas, yet is intended to fuel the same goal. To help Additive Manufacturing technologies one step closer to becoming the autonomous, digital manufacturing method of tomorrow. Vision...... systems A paradox exist in the field of Additive Manufacturing. The technologies allow for close-to unrestrained and integral geometrical freedom. Almost any geometry can be manufactured fast, e"ciently and cheap. Something that has been missing fundamental capability since the entering of the industrial...

  3. 77 FR 19718 - Manufacturer of Controlled Substances; Notice of Registration, Norac Inc.

    Science.gov (United States)

    2012-04-02

    ... Nabilone (7379) only, the company presently manufactures a small amount of this controlled substance in bulk solely to conduct manufacturing internal process development. It is the company's intention once... (1105) only, the company manufactures these controlled substances in bulk solely for domestic...

  4. 77 FR 5848 - Manufacturer of Controlled Substances; Notice of Registration

    Science.gov (United States)

    2012-02-06

    ... October 7, 2011, 76 FR 62449, Johnson Matthey Inc., Custom Pharmaceuticals Department, 2003 Nolte Drive... substance listed in schedule II. The company plans to manufacture the listed controlled substance for sale... registration of Johnson Matthey Inc. to manufacture the listed basic class of controlled substance is...

  5. Chemistry, manufacturing and controls in passive transdermal drug delivery systems.

    Science.gov (United States)

    Goswami, Tarun; Audett, Jay

    2015-01-01

    Transdermal drug delivery systems (TDDS) are used for the delivery of the drugs through the skin into the systemic circulation by applying them to the intact skin. The development of TDDS is a complex and multidisciplinary affair which involves identification of suitable drug, excipients and various other components. There have been numerous problems reported with respect to TDDS quality and performance. These problems can be reduced by appropriately addressing chemistry, manufacturing and controls requirements, which would thereby result in development of robust TDDS product and processes. This article provides recommendations on the chemistry, manufacturing and controls focusing on the unique technical aspects of TDDS.

  6. Controlling Lean Manufacturing in Multidivisional Organisations : Highlighting Local Interests and Contraints

    NARCIS (Netherlands)

    van der Steen, Martijn; Tillema, Sandra

    2018-01-01

    Purpose: This paper addresses the impact of a multidivisional structure on the implementation of lean manufacturing. It investigates how the controls employed by the corporate level impact the local implementation of lean manufacturing. Design/methodology/approach: The paper reports on case studies

  7. New Concepts and Theories For Intelligent Control of Cellular Manufacturing Systems

    DEFF Research Database (Denmark)

    Langer, Gilad

    1996-01-01

    This paper will present some new theories such as biological manufacturing system, the fractal factory theory, holonic manufacturing systems, agile manufacturing, object orientation, multi-agent theory, artificial intelligence, and artificial life in the context of manufacturing systems....... The paper tries to encapsulate the main area of my Ph.D. thesis research which will evolve around the idea of integrating intelligent elements into the control systems of the manufacturing systems. Furthermore it intends to show how the curriculum and discussions of the IPS Ph.D. course will and have...... contributed to my research. The research will concentrate on integration of manufacturing units by use of intelligent control mechanisms, information technology and the material handling as the key integrators....

  8. 76 FR 5829 - Manufacturer of Controlled Substances; Notice of Application

    Science.gov (United States)

    2011-02-02

    ... bulk manufacturer of the following basic classes of controlled substances: Drug Schedule Marihuana.... In reference to drug code 7360 (Marihuana), the company plans to bulk manufacture cannabidiol as a...

  9. Unified Controller Design for Intelligent Manufacturing Automation

    National Research Council Canada - National Science Library

    Kosut, Robert

    1997-01-01

    .... The demonstration system selected was rapid thermal processing (RTP) of semiconductor wafers. This novel approach in integrated circuit manufacturing demands fast tracking control laws that achieve near uniform spatial temperature distributions...

  10. Controlling high-throughput manufacturing at the nano-scale

    Science.gov (United States)

    Cooper, Khershed P.

    2013-09-01

    Interest in nano-scale manufacturing research and development is growing. The reason is to accelerate the translation of discoveries and inventions of nanoscience and nanotechnology into products that would benefit industry, economy and society. Ongoing research in nanomanufacturing is focused primarily on developing novel nanofabrication techniques for a variety of applications—materials, energy, electronics, photonics, biomedical, etc. Our goal is to foster the development of high-throughput methods of fabricating nano-enabled products. Large-area parallel processing and highspeed continuous processing are high-throughput means for mass production. An example of large-area processing is step-and-repeat nanoimprinting, by which nanostructures are reproduced again and again over a large area, such as a 12 in wafer. Roll-to-roll processing is an example of continuous processing, by which it is possible to print and imprint multi-level nanostructures and nanodevices on a moving flexible substrate. The big pay-off is high-volume production and low unit cost. However, the anticipated cost benefits can only be realized if the increased production rate is accompanied by high yields of high quality products. To ensure product quality, we need to design and construct manufacturing systems such that the processes can be closely monitored and controlled. One approach is to bring cyber-physical systems (CPS) concepts to nanomanufacturing. CPS involves the control of a physical system such as manufacturing through modeling, computation, communication and control. Such a closely coupled system will involve in-situ metrology and closed-loop control of the physical processes guided by physics-based models and driven by appropriate instrumentation, sensing and actuation. This paper will discuss these ideas in the context of controlling high-throughput manufacturing at the nano-scale.

  11. Wireless embedded control system for atomically precise manufacturing

    KAUST Repository

    Khan, Yasser; Randall, John N.

    2011-01-01

    This paper will explore the possibilities of implementing a wireless embedded control system for atomically precise manufacturing. The manufacturing process, similar to Scanning Tunneling Microscopy, takes place within an Ultra High Vacuum (UHV) chamber at a pressure of 10-10 torr. In order to create vibration isolation, and to keep internal noise to a minimum, a wireless link inside the UHV chamber becomes essential. We present a MATLAB simulation of the problem, and then demonstrate a hardware scheme between a Gumstix computer and a Linux based laptop for controlling nano-manipulators with three degrees of freedom. © 2011 IEEE.

  12. Wireless embedded control system for atomically precise manufacturing

    KAUST Repository

    Khan, Yasser

    2011-04-01

    This paper will explore the possibilities of implementing a wireless embedded control system for atomically precise manufacturing. The manufacturing process, similar to Scanning Tunneling Microscopy, takes place within an Ultra High Vacuum (UHV) chamber at a pressure of 10-10 torr. In order to create vibration isolation, and to keep internal noise to a minimum, a wireless link inside the UHV chamber becomes essential. We present a MATLAB simulation of the problem, and then demonstrate a hardware scheme between a Gumstix computer and a Linux based laptop for controlling nano-manipulators with three degrees of freedom. © 2011 IEEE.

  13. Statistical Data Mining for Efficient Quality Control in Manufacturing

    DEFF Research Database (Denmark)

    Khan, Abdul Rauf; Schiøler, Henrik; Knudsen, Torben Steen

    2015-01-01

    of the process e.g sensor measurements, machine readings etc, and the major contributor of these big data sets are different quality control processes. In this article we will present methodology to extract valuable insight from manufacturing data. The proposed methodology is based on comparison of probabilities...

  14. Automation in Siemens fuel manufacturing - the basis for quality improvement by statistical process control (SPC)

    International Nuclear Information System (INIS)

    Drecker, St.; Hoff, A.; Dietrich, M.; Guldner, R.

    1999-01-01

    Statistical Process Control (SPC) is one of the systematic tools to perform a valuable contribution to the control and planning activities for manufacturing processes and product quality. Advanced Nuclear Fuels GmbH (ANF) started a program to introduce SPC in all sections of the manufacturing process of fuel assemblies. The concept phase is based on a realization of SPC in 3 pilot projects. The existing manufacturing devices are reviewed for the utilization of SPC. Subsequent modifications were made to provide the necessary interfaces. The processes 'powder/pellet manufacturing'. 'cladding tube manufacturing' and 'laser-welding of spacers' are located at the different locations of ANF. Due to the completion of the first steps and the experience obtained by the pilot projects, the introduction program for SPC has already been extended to other manufacturing processes. (authors)

  15. Service Orientation in Holonic and Multi-Agent Manufacturing Control

    CERN Document Server

    Thomas, André; Trentesaux, Damien

    2012-01-01

    Service orientation is emerging nowadays at multiple organizational levels in enterprise business, and it leverages technology in response to the growing need for greater business integration, flexibility and agility of manufacturing enterprises. This book gathers contributions from scientists, researchers and industrialists on concepts, methods, frameworks and implementing issues addressing trends in the service orientation of control technology and management applied to manufacturing enterprise. It analyzes a Service Oriented Architecture (SOA) representing a technical architecture, a business modelling concept, a type of infrastructure, an integration source and a new way of viewing units of automation within the enterprise. The presents how SOA aligns the business world with the world of information technology in a way that makes both more effective.  

  16. 75 FR 9614 - Manufacturer of Controlled Substances; Notice of Registration

    Science.gov (United States)

    2010-03-03

    ... manufacturer of the basic classes of controlled substances listed in schedule I: Drug Schedule Marihuana (7360) I Tetrahydrocannabinols (7370) I The company plans to manufacture small quantities of marihuana derivatives for research purposes. In reference to drug code 7360 (Marihuana), the company plans to bulk...

  17. 75 FR 64744 - Manufacturer of Controlled Substances; Notice of Application

    Science.gov (United States)

    2010-10-20

    ... manufacturer of the basic classes of controlled substances listed in schedule I: Drug Schedule Marihuana (7360) I Tetrahydrocannabinols (7370) I The company plans to manufacture small quantities of marihuana derivatives for research purposes. In reference to drug code 7360 (Marihuana), the company plans to bulk...

  18. MapReduce Based Parallel Bayesian Network for Manufacturing Quality Control

    Science.gov (United States)

    Zheng, Mao-Kuan; Ming, Xin-Guo; Zhang, Xian-Yu; Li, Guo-Ming

    2017-09-01

    Increasing complexity of industrial products and manufacturing processes have challenged conventional statistics based quality management approaches in the circumstances of dynamic production. A Bayesian network and big data analytics integrated approach for manufacturing process quality analysis and control is proposed. Based on Hadoop distributed architecture and MapReduce parallel computing model, big volume and variety quality related data generated during the manufacturing process could be dealt with. Artificial intelligent algorithms, including Bayesian network learning, classification and reasoning, are embedded into the Reduce process. Relying on the ability of the Bayesian network in dealing with dynamic and uncertain problem and the parallel computing power of MapReduce, Bayesian network of impact factors on quality are built based on prior probability distribution and modified with posterior probability distribution. A case study on hull segment manufacturing precision management for ship and offshore platform building shows that computing speed accelerates almost directly proportionally to the increase of computing nodes. It is also proved that the proposed model is feasible for locating and reasoning of root causes, forecasting of manufacturing outcome, and intelligent decision for precision problem solving. The integration of bigdata analytics and BN method offers a whole new perspective in manufacturing quality control.

  19. Manufacturing Squares: An Integrative Statistical Process Control Exercise

    Science.gov (United States)

    Coy, Steven P.

    2016-01-01

    In the exercise, students in a junior-level operations management class are asked to manufacture a simple product. Given product specifications, they must design a production process, create roles and design jobs for each team member, and develop a statistical process control plan that efficiently and effectively controls quality during…

  20. Sensing and controlling resin-layer thickness in additive manufacturing processes

    NARCIS (Netherlands)

    Kozhevnikov, A.

    2017-01-01

    This AM-TKI project in collaboration with TNO focusses on the sensing and control of resin-layer thickness in AM applications. Industrial Additive Manufacturing is considered to be a potential breakthrough production technology for many applications. A specific AM implementation is VAT photo

  1. 76 FR 17778 - Control of Ergocristine, a Chemical Precursor Used in the Illicit Manufacture of Lysergic Acid...

    Science.gov (United States)

    2011-03-31

    ... 1117-AB24 Control of Ergocristine, a Chemical Precursor Used in the Illicit Manufacture of Lysergic... for the List I chemicals ergotamine and ergonovine to illicitly manufacture the schedule I controlled..., due to growing concerns regarding its use for the illicit manufacture of LSD. [[Page 17779...

  2. Vibration control for precision manufacturing at Sandia National Laboratories

    International Nuclear Information System (INIS)

    Hinnerichs, T.; Martinez, D.

    1995-01-01

    Sandia National Laboratories performs R and D in structural dynamics and vibration suppression for precision applications in weapon systems, space, underwater, transportation and civil structures. Over the last decade these efforts have expanded into the areas of active vibration control and ''smart'' structures and material systems. In addition, Sandia has focused major resources towards technology to support weapon product development and agile manufacturing capability for defense and industrial applications. This paper will briefly describe the structural dynamics modeling and verification process currently in place at Sandia that supports vibration control and some specific applications of these techniques to manufacturing in the areas of lithography, machine tools and flexible robotics

  3. Vibration control for precision manufacturing at Sandia National Laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Hinnerichs, T.; Martinez, D. [Sandia National Labs., Albuquerque, NM (United States). Structural Dynamics and Vibration Control Dept.

    1995-04-01

    Sandia National Laboratories performs R and D in structural dynamics and vibration suppression for precision applications in weapon systems, space, underwater, transportation and civil structures. Over the last decade these efforts have expanded into the areas of active vibration control and ``smart`` structures and material systems. In addition, Sandia has focused major resources towards technology to support weapon product development and agile manufacturing capability for defense and industrial applications. This paper will briefly describe the structural dynamics modeling and verification process currently in place at Sandia that supports vibration control and some specific applications of these techniques to manufacturing in the areas of lithography, machine tools and flexible robotics.

  4. QUALITY CONTROL IN PRECAST PRODUCTION A case study on Tunnel Segment Manufacture

    Directory of Open Access Journals (Sweden)

    Yee Weng Cheong

    2005-01-01

    Full Text Available Quality control forms an integral part of precast production. An efficient quality system is most critical in the mass production of precast components in any project. In this study, the quality control system implemented in a precast factory is discussed. The precast factory is set up for the manufacture of large quantity of tunnel segments under a contract. Processes in the precast manufacture are discussed with respect to the control procedures in the quality inspection plan. The standard tests involved, roles of inspectors and corrective actions on-site are highlighted. Critical issues pertaining to the productivity and quality of precast production are reviewed. These include the quality of staff and maintenance, which could potentially affect the efficiency of the quality system. Some considerations should also be given to improve the workflow and productivity of the plant.

  5. Sensor fusion control system for computer integrated manufacturing

    CSIR Research Space (South Africa)

    Kumile, CM

    2007-08-01

    Full Text Available -floor control using sensors previously missing in manufacturing research. The contribution is in the ease and the elegance that the concept provides finite state/ automata activities as well as the production engineering elements such as planning...

  6. [Pharmaceutical product quality control and good manufacturing practices].

    Science.gov (United States)

    Hiyama, Yukio

    2010-01-01

    This report describes the roles of Good Manufacturing Practices (GMP) in pharmaceutical product quality control. There are three keys to pharmaceutical product quality control. They are specifications, thorough product characterization during development, and adherence to GMP as the ICH Q6A guideline on specifications provides the most important principles in its background section. Impacts of the revised Pharmaceutical Affairs Law (rPAL) which became effective in 2005 on product quality control are discussed. Progress of ICH discussion for Pharmaceutical Development (Q8), Quality Risk Management (Q9) and Pharmaceutical Quality System (Q10) are reviewed. In order to reconstruct GMP guidelines and GMP inspection system in the regulatory agencies under the new paradigm by rPAL and the ICH, a series of Health Science studies were conducted. For GMP guidelines, product GMP guideline, technology transfer guideline, laboratory control guideline and change control system guideline were written. For the GMP inspection system, inspection check list, inspection memo and inspection scenario were proposed also by the Health Science study groups. Because pharmaceutical products and their raw materials are manufactured and distributed internationally, collaborations with other national authorities are highly desired. In order to enhance the international collaborations, consistent establishment of GMP inspection quality system throughout Japan will be essential.

  7. Current good manufacturing practice in manufacturing, processing, packing, or holding of drugs; revision of certain labeling controls. Final rule.

    Science.gov (United States)

    2012-03-20

    The Food and Drug Administration (FDA) is amending the packaging and labeling control provisions of the current good manufacturing practice (CGMP) regulations for human and veterinary drug products by limiting the application of special control procedures for the use of cut labeling to immediate container labels, individual unit cartons, or multiunit cartons containing immediate containers that are not packaged in individual unit cartons. FDA is also permitting the use of any automated technique, including differentiation by labeling size and shape, that physically prevents incorrect labeling from being processed by labeling and packaging equipment when cut labeling is used. This action is intended to protect consumers from labeling errors more likely to cause adverse health consequences, while eliminating the regulatory burden of applying the rule to labeling unlikely to reach or adversely affect consumers. This action is also intended to permit manufacturers to use a broader range of error prevention and labeling control techniques than permitted by current CGMPs.

  8. Modular mechatronic control of reconfigurable manufacturing system for mass customization manufacturing

    CSIR Research Space (South Africa)

    Xing, B

    2007-01-01

    Full Text Available Manufacturing companies are faced with the challenge of unpredictable, high frequency market changes in both local and international markets. There is a need for greater, more effective responsiveness by manufacturers to change their manufacturing...

  9. Unified Modeling of Discrete Event and Control Systems Applied in Manufacturing

    Directory of Open Access Journals (Sweden)

    Amanda Arêas de Souza

    2015-05-01

    Full Text Available For the development of both a simulation modeland a control system, it is necessary to build, inadvance, a conceptual model. This is what isusually suggested by the methodologies applied inprojects of this nature. Some conceptual modelingtechniques allow for a better understanding ofthe simulation model, and a clear descriptionof the logic of control systems. Therefore, thispaper aims to present and evaluate conceptuallanguages for unified modeling of models ofdiscrete event simulation and control systemsapplied in manufacturing. The results show thatthe IDEF-SIM language can be applied both insimulation systems and in process control.

  10. Process and control systems for composites manufacturing

    Science.gov (United States)

    Tsiang, T. H.; Wanamaker, John L.

    1992-01-01

    A precise control of composite material processing would not only improve part quality, but it would also directly reduce the overall manufacturing cost. The development and incorporation of sensors will help to generate real-time information for material processing relationships and equipment characteristics. In the present work, the thermocouple, pressure transducer, and dielectrometer technologies were investigated. The monitoring sensors were integrated with the computerized control system in three non-autoclave fabrication techniques: hot-press, self contained tool (self heating and pressurizing), and pressure vessel). The sensors were implemented in the parts and tools.

  11. Stochastic Lot-Sizing under Carbon Emission Control for Profit Optimisation in MTO Manufacturing

    Directory of Open Access Journals (Sweden)

    Qiao A.

    2017-01-01

    Full Text Available Aggravating global warming has heightened the imminent need by the world to step up forceful efforts on curbing emission of greenhouse gases. Although manufacturing is a major resource of carbon emission, few research works have studied the impacts of carbon constraints on manufacturing, leading to environmentally unsustainable production strategies and operations. This paper incorporates carbon emission management into production planning for make-to-order (MTO manufacturing. This paper proposes a model that solves lot-sizing problems to maximise profits under carbon emission caps. The model adopts stochastic interarrival times for customer orders to enhance the practicality of the results for real-world manufacturing. Numerical experiments show that reducing carbon emission undercuts short-term profits of a company. However, it is conducive to the company’s market image as being socially responsible which would attract more customers who concern about environmental protection. Hence, reducing carbon emission in manufacturing is beneficial to long-term profitability and sustainability. The results provide managerial insights into manufacture operations for balancing profitability and carbon control.

  12. A stochastic programming approach to manufacturing flow control

    OpenAIRE

    Haurie, Alain; Moresino, Francesco

    2012-01-01

    This paper proposes and tests an approximation of the solution of a class of piecewise deterministic control problems, typically used in the modeling of manufacturing flow processes. This approximation uses a stochastic programming approach on a suitably discretized and sampled system. The method proceeds through two stages: (i) the Hamilton-Jacobi-Bellman (HJB) dynamic programming equations for the finite horizon continuous time stochastic control problem are discretized over a set of sample...

  13. Artificial neural networks in variable process control: application in particleboard manufacture

    Energy Technology Data Exchange (ETDEWEB)

    Esteban, L. G.; Garcia Fernandez, F.; Palacios, P. de; Conde, M.

    2009-07-01

    Artificial neural networks are an efficient tool for modelling production control processes using data from the actual production as well as simulated or design of experiments data. In this study two artificial neural networks were combined with the control process charts and it was checked whether the data obtained by the networks were valid for variable process control in particleboard manufacture. The networks made it possible to obtain the mean and standard deviation of the internal bond strength of the particleboard within acceptable margins using known data of thickness, density, moisture content, swelling and absorption. The networks obtained met the acceptance criteria for test values from non-standard test methods, as well as the criteria for using these values in statistical process control. (Author) 47 refs.

  14. Lean Production Control at a High-Variety, Low-Volume Parts Manufacturer

    NARCIS (Netherlands)

    Bokhorst, Jos A. C.; Slomp, Jannes

    2010-01-01

    Eaton Electric General Supplies, a parts manufacturing unit that supplies parts for Eaton's electrical business unit, implemented several lean control elements in its high-variety, low-volume production units. These control elements include a constant work-in-process mechanism to limit and control

  15. Advances in compact manufacturing for shape and performance controllability of large-scale components-a review

    Science.gov (United States)

    Qin, Fangcheng; Li, Yongtang; Qi, Huiping; Ju, Li

    2017-01-01

    Research on compact manufacturing technology for shape and performance controllability of metallic components can realize the simplification and high-reliability of manufacturing process on the premise of satisfying the requirement of macro/micro-structure. It is not only the key paths in improving performance, saving material and energy, and green manufacturing of components used in major equipments, but also the challenging subjects in frontiers of advanced plastic forming. To provide a novel horizon for the manufacturing in the critical components is significant. Focused on the high-performance large-scale components such as bearing rings, flanges, railway wheels, thick-walled pipes, etc, the conventional processes and their developing situations are summarized. The existing problems including multi-pass heating, wasting material and energy, high cost and high-emission are discussed, and the present study unable to meet the manufacturing in high-quality components is also pointed out. Thus, the new techniques related to casting-rolling compound precise forming of rings, compact manufacturing for duplex-metal composite rings, compact manufacturing for railway wheels, and casting-extruding continuous forming of thick-walled pipes are introduced in detail, respectively. The corresponding research contents, such as casting ring blank, hot ring rolling, near solid-state pressure forming, hot extruding, are elaborated. Some findings in through-thickness microstructure evolution and mechanical properties are also presented. The components produced by the new techniques are mainly characterized by fine and homogeneous grains. Moreover, the possible directions for further development of those techniques are suggested. Finally, the key scientific problems are first proposed. All of these results and conclusions have reference value and guiding significance for the integrated control of shape and performance in advanced compact manufacturing.

  16. Integration of process-oriented control with systematic inspection in FRAMATOME-FBFC fuel manufacturing

    International Nuclear Information System (INIS)

    Kopff, G.

    2000-01-01

    The classical approach to quality control is essentially based on final inspection of the product conducted through a qualified process. The main drawback of this approach lies in the separation and , therefore, in the low feedback between manufacturing and quality control, leading to a very static quality system. As a remedy, the modern approach to quality management focuses on the need for continuous improvement through process-oriented quality control. In the classical approach, high reliability of nuclear fuel and high quality level of the main characteristics are assumed to be attained, at the manufacturing step, through 100% inspection of the product, generally with automated inspection equipment. Such a 100% final inspection is not appropriate to obtain a homogeneous product with minimum variability, and cannot be a substitute for the SPC tools (Statistical Process Control) which are rightly designed with this aim. On the other hand, SPC methods, which detect process changes and are used to keep the process u nder control , leading to the optimal distribution of the quality characteristics, do not protect against non systematic or local disturbances, at low frequency. Only systematic control is capable of detecting local quality troubles. In fact, both approaches, SPC and systematic inspection, are complementary , because they are remedies for distinct causes of process and product changes. The term 'statistical' in the expression 'SPC' refers less to the sampling techniques than to the control of global distribution parameters of product or process variables (generally location and dispersion parameters). The successive integration levels of process control methods with systematic inspection are described and illustrated by examples from FRAMATOME-FBFC fuel manufacturing, from the simple control chart for checking the performance stability of automated inspection equipment to the global process control system including systematic inspection. This kind of

  17. 75 FR 6062 - Manufacturer of Controlled Substances Notice of Registration

    Science.gov (United States)

    2010-02-05

    ... controlled substances listed in schedules I and II: Drug Schedule Marihuana (7360) I Tetrahydrocannabinols (7370) I Cocaine (9041) I The Institute will manufacture small quantities of cocaine and marihuana...

  18. 76 FR 66994 - Manufacturer of Controlled Substances; Notice of Application

    Science.gov (United States)

    2011-10-28

    ... following basic classes of controlled substances: Drug Schedule Marihuana (7360) I Cocaine (9041) II The Institute will manufacture marihuana, and cocaine derivatives for use by their customers in analytical kits...

  19. 76 FR 51401 - Manufacturer of Controlled Substances; Notice of Application

    Science.gov (United States)

    2011-08-18

    ... a bulk manufacturer of the following basic classes of controlled substances: Drug Schedule Marihuana... ingredients (APIs) for distribution to its customers. In reference to drug code 7360 (Marihuana), the company...

  20. Control of microstructure in soldered, brazed, welded, plated, cast or vapor deposited manufactured components

    Science.gov (United States)

    Ripley, Edward B.; Hallman, Russell L.

    2015-11-10

    Disclosed are methods and systems for controlling of the microstructures of a soldered, brazed, welded, plated, cast, or vapor deposited manufactured component. The systems typically use relatively weak magnetic fields of either constant or varying flux to affect material properties within a manufactured component, typically without modifying the alloy, or changing the chemical composition of materials or altering the time, temperature, or transformation parameters of a manufacturing process. Such systems and processes may be used with components consisting of only materials that are conventionally characterized as be uninfluenced by magnetic forces.

  1. Real-time product attribute control to manufacture antibodies with defined N-linked glycan levels.

    Science.gov (United States)

    Zupke, Craig; Brady, Lowell J; Slade, Peter G; Clark, Philip; Caspary, R Guy; Livingston, Brittney; Taylor, Lisa; Bigham, Kyle; Morris, Arvia E; Bailey, Robert W

    2015-01-01

    Pressures for cost-effective new therapies and an increased emphasis on emerging markets require technological advancements and a flexible future manufacturing network for the production of biologic medicines. The safety and efficacy of a product is crucial, and consistent product quality is an essential feature of any therapeutic manufacturing process. The active control of product quality in a typical biologic process is challenging because of measurement lags and nonlinearities present in the system. The current study uses nonlinear model predictive control to maintain a critical product quality attribute at a predetermined value during pilot scale manufacturing operations. This approach to product quality control ensures a more consistent product for patients, enables greater manufacturing efficiency, and eliminates the need for extensive process characterization by providing direct measures of critical product quality attributes for real time release of drug product. © 2015 American Institute of Chemical Engineers.

  2. 78 FR 46372 - Manufacturer of Controlled Substances; Notice of Registration; Research Triangle Institute

    Science.gov (United States)

    2013-07-31

    ... bulk manufacturer of the following basic classes of controlled substances: Drug Schedule Marihuana (7360) I Cocaine (9041) II The Institute will manufacture marihuana, and cocaine derivatives for use by...

  3. Vibration control for precision manufacturing using piezoelectric actuators

    Energy Technology Data Exchange (ETDEWEB)

    Martinez, D.R.; Hinnerichs, T.D.; Redmond, J.M.

    1995-12-31

    Piezoelectric actuators provide high frequency, force, and stiffness capabilities along with reasonable Stroke limits, all of which can be used to increase performance levels in precision manufacturing systems. This paper describes two examples of embedding piezoelectric actuators in structural components for vibration control. One example involves suppressing the self excited chatter phenomenon in the metal cutting process of a milling machine and the other involves damping vibrations induced by rigid body stepping of a photolithography platen. Finite element modeling and analyses are essential for locating and sizing the actuators and permit further simulation studies of the response of the dynamic system. Experimental results are given for embedding piezoelectric actuators in a cantilevered bar configuration, which was used as a surrogate machine tool structure. These results are incorporated into a previously developed milling process simulation and the effect of the control on the cutting process stability diagram is quantified. Experimental results are also given for embedding three piezoelectric actuators in a surrogate photolithography platen to suppress vibrations. These results demonstrate the potential benefit that can be realized by applying advances from the field of adaptive structures to problems in precision manufacturing.

  4. Process and quality control in manufacturing of nuclear fuel assemblies of LWRs

    International Nuclear Information System (INIS)

    Dietrich, M.; Hoff, A.; Reimann, P.

    2000-01-01

    Manufacturing of nuclear fuel assemblies requires a multitude of different process and quality methods to assure and maintain a high quality level. In recent years methods have been applied which prevent deviations rather than detect deviant products. This paper gives an example on how to control a complex manufacturing process by using a small number of key parameters and second, it demonstrates the importance of graphical data evaluation and presentation methods. In the past many product and product characteristics were inspected m comparison with specification limits only. However, todays methods allow the early identification of trends, increase of variation, shifts disturbances etc. before the product characteristics exceed the specification limits. These methods are process control charts, x-y-plots, boxplots, failure mode and effect analysis (FMEA), process capability numbers and others. This paper demonstrates the beneficial use of some of the methods by presenting selected examples applied at Advanced Nuclear Fuels GmbH (ANF). (author)

  5. A system architecture for holonic manufacturing planning and control (EtoPlan)

    NARCIS (Netherlands)

    Wullink, Gerhard; Giebels, M.M.T.; Kals, H.J.J.

    2002-01-01

    In this paper, we present the system architecture of a flexible manufacturing planning and control system, named EtoPlan. The concept is based on the holonic control approach of building multiple and temporary hierarchies (holarchies). This paper describes the system architecture for flexible

  6. Modeling and Control of a Manufacturing Flow Line using Partial Differential Equations

    NARCIS (Netherlands)

    Berg, van den R.A.; Lefeber, A.A.J.; Rooda, J.E.

    2008-01-01

    This brief deals with a control framework for manufacturing flow lines. For this framework, a continuous approximation model of the manufacturing system is required, which is computationally feasible and able to accurately describe the dynamics of the system (both throughput and flow time). Often

  7. Self-organization principles result in robust control of flexible manufacturing systems

    DEFF Research Database (Denmark)

    Nature shows us in our daily life how robust, flexible and optimal self-organized modular constructions work in complex physical, chemical and biological systems, which successfully adapt to new and unexpected situations. A promising strategy is therefore to use such self-organization and pattern...... problems with several autonomous robots and several targets are considered as model of flexible manufacturing systems. Each manufacturing target has to be served in a given time interval by one and only one robot and the total working costs have to be minimized (or total winnings maximized). A specifically...... constructed dynamical system approach (coupled selection equations) is used which is based on pattern formation principles and results in fault resistant and robust behaviour. An important feature is that this type of control also guarantees feasiblitiy of the assignment solutions. In previous work...

  8. Tracing and control of raw materials sourcing for vaccine manufacturers.

    Science.gov (United States)

    Faretra Peysson, Laurence

    2010-05-01

    The control of the raw materials used to manufacture vaccines is mandatory; therefore, a very clear process must be in place to guarantee that raw materials are traced. Those who make products or supplies used in vaccine manufacture (suppliers of culture media, diagnostic tests, etc.) must apply quality systems proving that they adhere to certain standards. ISO certification, Good Manufacturing Practices for production sites and the registration of culture media with a 'Certificate of Suitability' from the European Directorate for the Quality of Medicines and Healthcare are reliable quality systems pertaining to vaccine production. Suppliers must assure that each lot of raw materials used in a product that will be used in vaccine manufacture adheres to the level of safety and traceability required. Incoming materials must be controlled in a single 'Enterprise Resource Planning' system which is used to document important information, such as the assignment of lot number, expiration date, etc. Ingredients for culture media in particular must conform to certain specifications. The specifications that need to be checked vary according to the ingredient, based on the level of risk. The way a raw material is produced is also important, and any aspect relative to cross-contamination, such as the sanitary measures used in producing and storing the raw material must be checked as well. In addition, suppliers can reduce the risk of viral contamination of raw materials by avoiding purchases in countries where a relevant outbreak is currently declared. 2010 The International Association for Biologicals. Published by Elsevier Ltd. All rights reserved.

  9. 77 FR 16158 - Current Good Manufacturing Practice in Manufacturing, Processing, Packing, or Holding of Drugs...

    Science.gov (United States)

    2012-03-20

    .... FDA-1997-N-0518] (formerly 97N-0300) Current Good Manufacturing Practice in Manufacturing, Processing... labeling control provisions of the current good manufacturing practice (CGMP) regulations for human and... GOOD MANUFACTURING PRACTICE FOR FINISHED PHARMACEUTICALS 0 1. The authority citation for 21 CFR part...

  10. Data-driven modeling and real-time distributed control for energy efficient manufacturing systems

    International Nuclear Information System (INIS)

    Zou, Jing; Chang, Qing; Arinez, Jorge; Xiao, Guoxian

    2017-01-01

    As manufacturers face the challenges of increasing global competition and energy saving requirements, it is imperative to seek out opportunities to reduce energy waste and overall cost. In this paper, a novel data-driven stochastic manufacturing system modeling method is proposed to identify and predict energy saving opportunities and their impact on production. A real-time distributed feedback production control policy, which integrates the current and predicted system performance, is established to improve the overall profit and energy efficiency. A case study is presented to demonstrate the effectiveness of the proposed control policy. - Highlights: • A data-driven stochastic manufacturing system model is proposed. • Real-time system performance and energy saving opportunity identification method is developed. • Prediction method for future potential system performance and energy saving opportunity is developed. • A real-time distributed feedback control policy is established to improve energy efficiency and overall system profit.

  11. Quality assurance and control in the manufacture of metalclad UO2 reactor fuels

    International Nuclear Information System (INIS)

    1976-01-01

    The International Atomic Energy Agency has carried out a programme since its earliest days that includes the collection and dissemination of information on nuclear fuels. Since the 1960 symposium on Fuel Element Fabrication with Special Emphasis on Cladding Materials there has been an average of one meeting a year reviewing some aspect of fuel fabrication technology. A recent meeting dealing with the fabrication of UO 2 fuels was the Study Group on the Facilities and Technology needed for Nuclear Fuel Manufacture, held in Grenoble in 1972 (Rep. IAEA-158). After that meeting it became apparent that the quality of fuel production was an important aspect that had received inadequate coverage so far, and the Panel on Quality Assurance and Control in Nuclear Fuel Manufacture was convened by the Agency in Vienna in November 1974. In the working papers and discussions at the Panel meeting the viewpoints of different countries and of various interested parties, such as manufacturers, reactor operators and government authorities, were presented

  12. The manufacture, quality control and performance of KANUPP fuel

    International Nuclear Information System (INIS)

    Butt, M.I.; Salim, M.; Ahmad, I.

    1989-01-01

    KANUPP is a 137 MWe CANDU reactor. The fuel material is high-density sintered pellets (95-97% T.D.) of natural UO 2 in Zircaloy 4 sheaths. Reactor-grade UO 2 powder is precompacted, granulated, blended with 0.2% zinc stearate, and compacted into green pellets. The pellets are sintered in a reducing atmosphere, then finished by grinding, culled, and loaded into Zr-4 tubes. The welded elements are assembled into a fuel bundle. Quality control and quality assurance procedures are followed during all stages of manufacturing. The entire core of KANUPP now consists of locally manufactured fuel. Several bundles have already achieved the design burnup (8650 MWD/TU). There have never been any failures of these fuel bundles. (6 refs., 5 figs., 8 tabs.)

  13. 76 FR 39128 - Manufacturer of Controlled Substances; Notice of Registration

    Science.gov (United States)

    2011-07-05

    ... February 23, 2011, 76 FR 10068, Johnson Matthey Pharmaceutical Materials Inc., Pharmaceutical Service, 25...) II Sufentanil (9740) II Hydrocodone (9193) II The company plans to utilize this facility to... support of the company's primary manufacturing facility in West Deptford, New Jersey. The controlled...

  14. 76 FR 17969 - Manufacturer of Controlled Substances; Notice of Registration

    Science.gov (United States)

    2011-03-31

    ... DEPARTMENT OF JUSTICE Drug Enforcement Administration Manufacturer of Controlled Substances; Notice of Registration By Notice dated November 1, 2010, and published in the Federal Register on November 12, 2010, 75 FR 69464, Cerilliant Corporation, 811 Paloma Drive, Suite A, Round Rock, Texas 78665...

  15. 75 FR 10314 - Manufacturer of Controlled Substances; Notice of Registration

    Science.gov (United States)

    2010-03-05

    ... DEPARTMENT OF JUSTICE Drug Enforcement Administration Manufacturer of Controlled Substances; Notice of Registration By Notice dated September 17, 2009, and published in the Federal Register on September 25, 2009, (74 FR 49020), Cerilliant Corporation, 811 Paloma Drive, Suite A, Round Rock, Texas...

  16. Control of criticality risk in the manufacture of fuel elements for research reactors

    International Nuclear Information System (INIS)

    Friedenthal, M.; Cardenas Yucra, H.R.; Marajofsky, A.; La Gamma de Batistoni, A.M.

    1987-01-01

    The control of criticality risk in a chemical plant adopts different forms according to the quantities of fissile material and the type of compounds used. This work presents the treatment of the critical excursion risk adopted in production plants of U 3 O 8 and manufacturing plants of fuel elements for research reactors, located in Constituyentes Atomic Center. The possible events and accidents related to the fissile material control are analyzed, and the systems of administrative control and intrinsic safety through engineering are described. (Author)

  17. 78 FR 12102 - Manufacturer of Controlled Substances; Notice of Application; Mallinckrodt, LLC

    Science.gov (United States)

    2013-02-21

    ... plans to manufacture the listed controlled substances for internal use and for sale to other companies... Enforcement Administration, Office of Diversion Control, Federal Register Representative (ODL), 8701...: February 8, 2013. Joseph T. Rannazzisi, Deputy Assistant Administrator, Office of Diversion Control, Drug...

  18. Fuzzy process control and knowledge engineering in petrochemical and robotic manufacturing

    Energy Technology Data Exchange (ETDEWEB)

    Aliev, R. (Azerbaijan Industrial Univ., Dept. of Automatic Control Systems, Baku (Russia)); Aliev, F. (Azerbaijan Polytechnique Institute, Dept. of Automation and Computer Science, Baku (Russia)); Babaev, M. (Azerbaijan Industrial Univ., Laboratory of Intelligent Control Systems, Baku (Russia))

    1991-01-01

    This book presents the methodology, the functionality and the pragmatics of implementing and applying AI (Artificial Intelligence) techniques enhanced by the new mathematical discipline of fuzzy sets. Emphasis is put on the design and modelling of fuzzy controllers and intelligent control equipment for the oil processing and chemical industries, as well as on robotics and CAM (Computer-Aided Manufacturing), including the development of appropriate algorithms and computer programs. The content is strongly application-oriented in order to explain the main features of the theory of fuzzy systems using different real examples from concrete engineering projects. It excels over the present literature available on this subject by its descriptions new classes of industrial systems to be controlled with fuzzy logic, as well as by its descriptive introduction to intelligent control systems and fuzzy controllers developed and successfully implemented by the authors in working industrial plants. (orig.).

  19. 76 FR 10069 - Manufacturer of Controlled Substances; Notice of Registration

    Science.gov (United States)

    2011-02-23

    ... time. DEA has investigated Johnson Matthey Inc. to ensure that the company's registration is consistent... 26, 2010, 75 FR 65659, Johnson Matthey Inc., Custom Pharmaceuticals Department, 2003 Nolte Drive... Sufentanil (9740) II Fentanyl (9801) II The company plans to manufacture the listed controlled substances in...

  20. 75 FR 9615 - Manufacturer of Controlled Substances Notice of Registration

    Science.gov (United States)

    2010-03-03

    .... DEA has investigated Johnson Matthey Inc. to ensure that the company's registration is consistent with..., 2009, (74 FR 55588), Johnson Matthey Inc., Custom Pharmaceuticals Department, 2003 Nolte Drive, West... Sufentanil (9740) II Fentanyl (9801) II The company plans to manufacture the listed controlled substances in...

  1. Leukaemia incidence among workers in the shoe and boot manufacturing industry: a case-control study

    Directory of Open Access Journals (Sweden)

    Forand Steven P

    2004-08-01

    Full Text Available Abstract Background Previous reports have indicated an excess of leukaemia in Broome County, New York, particularly in the Town of Union. Surveillance of cancer incidence data indicates that a large proportion of these cases occurred among males ages 65 and older. Shoe and boot manufacturing has been the largest single industry in this area throughout much of the past century. Occupational studies from Europe suggest a link between leukaemia and employment in the shoe and boot manufacturing industry. However, researchers have not found a positive association between leukaemia and employment in the shoe industry among workers in the United States. Methods A matched case-control study was conducted to investigate the association between leukaemia incidence among males 65 and older and employment in the shoe and boot manufacturing industry. Thirty-six cases of leukaemia occurring between 1981–1990; among males age 65 and older; residing in the town of Union met the study case criteria. Death certificates were obtained for each of the cases. These were matched to death certificates of 144 controls on date of death and date of birth +/- 1 year. Death certificates were then examined to determine the employer and occupation of each study subject. Conditional logistic regression was used to determine the risk of leukaemia among those working in the industry. Results The risk of both leukaemia (OR = 1.47; 95% CI 0.70, 3.09 and acute myeloid leukaemia (OR = 1.19; 95% CI 0.33, 4.28 were elevated among those employed in the shoe and boot manufacturing industry, however neither was statistically significant. Conclusion The results, though suggestive of an association between leukaemia and employment in the shoe and boot manufacturing industry, were not statistically conclusive due mainly to limited study power. Several additional limitations may also have prevented the observance of more conclusive findings. Better exposure assessment, information on

  2. 78 FR 64425 - Current Good Manufacturing Practice and Hazard Analysis and Risk-Based Preventive Controls for...

    Science.gov (United States)

    2013-10-29

    ..., 507, and 579 [Docket No. FDA-2011-N-0922] Current Good Manufacturing Practice and Hazard Analysis and... requirements for current good manufacturing practice and hazard analysis and risk-based preventive controls for..., packing, or holding of animal food in two ways. First, it would create new current good manufacturing...

  3. North Carolina Tobacco Farmers' Changing Perceptions of Tobacco Control and Tobacco Manufacturers

    Science.gov (United States)

    Crankshaw, Erik C.; Beach, Robert H.; Austin, W. David; Altman, David G.; Jones, Alison Snow

    2009-01-01

    Purpose: To examine tobacco farmers' attitudes toward tobacco control, public health, and tobacco manufacturers in order to determine the extent to which rapidly changing economic conditions have influenced North Carolina tobacco farmer attitudes in ways that may provide tobacco control advocates with new opportunities to promote tobacco control…

  4. 76 FR 36578 - Manufacturer of Controlled Substances; Notice of Registration

    Science.gov (United States)

    2011-06-22

    ... firm plans to manufacture the listed controlled substances for internal use and for sale to other companies. No comments or objections have been received. DEA has considered the factors in 21 U.S.C. 823(a..., Inc., to ensure that the company's registration is consistent with the public interest. The...

  5. 75 FR 44287 - Manufacturer of Controlled Substances; Notice of Registration

    Science.gov (United States)

    2010-07-28

    ... firm plans to manufacture the listed controlled substances for internal use and for sale to other companies. No comments or objections have been received. DEA has considered the factors in 21 U.S.C. 823(a..., Inc., to ensure that the company's registration is consistent with the public interest. The...

  6. Statistical and Computational Techniques in Manufacturing

    CERN Document Server

    2012-01-01

    In recent years, interest in developing statistical and computational techniques for applied manufacturing engineering has been increased. Today, due to the great complexity of manufacturing engineering and the high number of parameters used, conventional approaches are no longer sufficient. Therefore, in manufacturing, statistical and computational techniques have achieved several applications, namely, modelling and simulation manufacturing processes, optimization manufacturing parameters, monitoring and control, computer-aided process planning, etc. The present book aims to provide recent information on statistical and computational techniques applied in manufacturing engineering. The content is suitable for final undergraduate engineering courses or as a subject on manufacturing at the postgraduate level. This book serves as a useful reference for academics, statistical and computational science researchers, mechanical, manufacturing and industrial engineers, and professionals in industries related to manu...

  7. Compliance and control characteristics of an additive manufactured-flexure stage

    Energy Technology Data Exchange (ETDEWEB)

    Lee, ChaBum; Tarbutton, Joshua A. [Department of Mechanical Engineering, University of South Carolina, 300 Main St., Columbia, South Carolina 29208 (United States)

    2015-04-15

    This paper presents a compliance and positioning control characteristics of additive manufactured-nanopositioning system consisted of the flexure mechanism and voice coil motor (VCM). The double compound notch type flexure stage was designed to utilize the elastic deformation of two symmetrical four-bar mechanisms to provide a millimeter-level working range. Additive manufacturing (AM) process, stereolithography, was used to fabricate the flexure stage. The AM stage was inspected by using 3D X-ray computerized tomography scanner: air-voids and shape irregularity. The compliance, open-loop resonance peak, and damping ratio of the AM stage were measured 0.317 mm/N, 80 Hz, and 0.19, respectively. The AM stage was proportional-integral-derivative positioning feedback-controlled and the capacitive type sensor was used to measure the displacement. As a result, the AM flexure mechanism was successfully 25 nm positioning controlled within 500 μm range. The resonance peak was found approximately at 280 Hz in closed-loop. This research showed that the AM flexure mechanism and the VCM can provide millimeter range with high precision and can be a good alternative to an expensive metal-based flexure mechanism and piezoelectric transducer.

  8. Compliance and control characteristics of an additive manufactured-flexure stage

    International Nuclear Information System (INIS)

    Lee, ChaBum; Tarbutton, Joshua A.

    2015-01-01

    This paper presents a compliance and positioning control characteristics of additive manufactured-nanopositioning system consisted of the flexure mechanism and voice coil motor (VCM). The double compound notch type flexure stage was designed to utilize the elastic deformation of two symmetrical four-bar mechanisms to provide a millimeter-level working range. Additive manufacturing (AM) process, stereolithography, was used to fabricate the flexure stage. The AM stage was inspected by using 3D X-ray computerized tomography scanner: air-voids and shape irregularity. The compliance, open-loop resonance peak, and damping ratio of the AM stage were measured 0.317 mm/N, 80 Hz, and 0.19, respectively. The AM stage was proportional-integral-derivative positioning feedback-controlled and the capacitive type sensor was used to measure the displacement. As a result, the AM flexure mechanism was successfully 25 nm positioning controlled within 500 μm range. The resonance peak was found approximately at 280 Hz in closed-loop. This research showed that the AM flexure mechanism and the VCM can provide millimeter range with high precision and can be a good alternative to an expensive metal-based flexure mechanism and piezoelectric transducer

  9. 76 FR 72976 - Manufacturer of Controlled Substances; Notice of Registration

    Science.gov (United States)

    2011-11-28

    ..., 2011, 76 FR 36577, Boehringer Ingelheim Chemicals, Inc., 2820 N. Normandy Drive, Petersburg, Virginia... Boehringer Ingelheim Chemicals, Inc., to manufacture the listed basic classes of controlled substances is consistent with the public interest at this time. DEA has investigated Boehringer Ingelheim Chemicals, Inc...

  10. Analytical chemistry in semiconductor manufacturing: Techniques, role of nuclear methods and need for quality control

    International Nuclear Information System (INIS)

    1989-06-01

    This report is the result of a consultants meeting held in Gaithersburg, USA, 2-3 October 1987. The meeting was hosted by the National Bureau of Standards and Technology, and it was attended by 18 participants from Denmark, Finland, India, Japan, Norway, People's Republic of China and the USA. The purpose of the meeting was to assess the present status of analytical chemistry in semiconductor manufacturing, the role of nuclear analytical methods and the need for internationally organized quality control of the chemical analysis. The report contains the three presentations in full and a summary report of the discussions. Thus, it gives an overview of the need of analytical chemistry in manufacturing of silicon based devices, the use of nuclear analytical methods, and discusses the need for quality control. Refs, figs and tabs

  11. 77 FR 5849 - Manufacturer of Controlled Substances; Notice of Registration

    Science.gov (United States)

    2012-02-06

    ... October 7, 2011, 76 FR 62449, Cambrex Charles City, Inc., 1205 11th Street, Charles City, Iowa 50616, made... Sufentanil (9740) II Fentanyl (9801) II The company will manufacture the listed controlled substances in bulk... factors in 21 U.S.C. 823(a) and determined that the registration of Cambrex Charles City, Inc. to...

  12. RECONFIGURABLE PRODUCT ROUTING AND CONTROL FOR MASS CUSTOMISATION MANUFACTURING

    Directory of Open Access Journals (Sweden)

    A. J. Walker

    2012-01-01

    Full Text Available

    ENGLISH ABSTRACT:Reconfigurable control of flexible manufacturing systems can allow for the efficient and responsive production of customised product instances. This can aid in providing make-to-order business models for various small- to medium-sized enterprises in South Africa, and provide competitive advantage in a dynamic global marketplace. Reconfigurable control application requires an understanding of the modes of production variability in mass customisation manufacturing. Temporally uncorrelated workflow routings are considered as one of these production variability modes. In this light, this paper addresses the flexible material payload routing problem, and presents a mobile robot platform that has been developed to research and design reconfigurable routing systems.

    AFRIKAANSE OPSOMMING:Verstelbare beheer van aanpasbare vervaardigingstelsels kan die doeltreffende en reaktiewe produksie van doelgemaakte produkeksemplare toelaat. Hierdie beheer kan assisteer in die voorsiening van vervaardig-na-bestellingbesigheidsmodelle aan ’n aantal klein- tot medium-grootte ondernemings in Suid-Afrika, en aan hulle ’n kompeterende voorsprong bied in ’n dinamiese globale mark. Die instelling van verstelbare beheer vereis dat die modi van produkveranderlikheid in massa verbruikersaanpassingsvervaardiging verstaan word. Hierdie artikel spreek die probleem van aanpasbare roetebepaling van materiaalvragte in massa verbruikersaanpassingsvervaardiging aan. ’n Mobiele robot-platform, ontwikkel vir navorsing in verstelbare roetebepalingstelsels, word ook voorgelê.

  13. 75 FR 69464 - Manufacturer of Controlled Substances; Notice of Application

    Science.gov (United States)

    2010-11-12

    ... DEPARTMENT OF JUSTICE Drug Enforcement Administration Manufacturer of Controlled Substances; Notice of Application Pursuant to Sec. 1301.33(a), Title 21 of the Code of Federal Regulations (CFR), this is notice that on July 16, 2009, Cerilliant Corporation, 811 Paloma Drive, Suite A, Round Rock...

  14. 77 FR 2321 - Manufacturer of Controlled Substances; Notice of Application

    Science.gov (United States)

    2012-01-17

    ... DEPARTMENT OF JUSTICE Drug Enforcement Administration Manufacturer of Controlled Substances; Notice of Application Pursuant to Sec. 1301.33(a), Title 21 of the Code of Federal Regulations (CFR), this is notice that on June 28, 2011, Cerilliant Corporation, 811 Paloma Drive, Suite A, Round Rock...

  15. 14 CFR 21.143 - Quality control data requirements; prime manufacturer.

    Science.gov (United States)

    2010-01-01

    ... with a chart indicating the functional relationship of the quality control organization to management..., purchased items, and parts and assemblies produced by manufacturers' suppliers including methods used to... delegation of authority to suppliers to make major inspections of parts or assemblies for which the prime...

  16. 76 FR 36577 - Manufacturer of Controlled Substances; Notice of Application

    Science.gov (United States)

    2011-06-22

    ... DEPARTMENT OF JUSTICE Drug Enforcement Administration Manufacturer of Controlled Substances; Notice of Application Pursuant to Sec. 1301.33(a), Title 21 of the Code of Federal Regulations (CFR), this is notice that on May 4, 2011, Boehringer Ingelheim Chemicals Inc., 2820 N. Normandy Drive...

  17. 75 FR 32506 - Manufacturer of Controlled Substances; Notice of Application

    Science.gov (United States)

    2010-06-08

    ... DEPARTMENT OF JUSTICE Drug Enforcement Administration Manufacturer of Controlled Substances; Notice of Application Pursuant to Sec. 1301.33(a) of Title 21 of the Code of Federal Regulations (CFR), this is notice that on April 12, 2010, Boehringer Ingelheim Chemicals Inc., 2820 N. Normandy Drive...

  18. Statistical applications for chemistry, manufacturing and controls (CMC) in the pharmaceutical industry

    CERN Document Server

    Burdick, Richard K; Pfahler, Lori B; Quiroz, Jorge; Sidor, Leslie; Vukovinsky, Kimberly; Zhang, Lanju

    2017-01-01

    This book examines statistical techniques that are critically important to Chemistry, Manufacturing, and Control (CMC) activities. Statistical methods are presented with a focus on applications unique to the CMC in the pharmaceutical industry. The target audience consists of statisticians and other scientists who are responsible for performing statistical analyses within a CMC environment. Basic statistical concepts are addressed in Chapter 2 followed by applications to specific topics related to development and manufacturing. The mathematical level assumes an elementary understanding of statistical methods. The ability to use Excel or statistical packages such as Minitab, JMP, SAS, or R will provide more value to the reader. The motivation for this book came from an American Association of Pharmaceutical Scientists (AAPS) short course on statistical methods applied to CMC applications presented by four of the authors. One of the course participants asked us for a good reference book, and the only book recomm...

  19. Lithography-based addtive manufacture of ceramic biodevices with design-controlled surface topographies

    OpenAIRE

    Blas Romero, Adrián de; Pfaffinger, Markus; Mitteramskogler, Gerald; Schwentenwein, Martin; Jellinek, Christopher; Homa, Johannes; Díaz Lantada, Andrés; Stampfl, Jürgen

    2017-01-01

    The possibility of manufacturing textured materials and devices, with surface properties controlled from the design stage, instead of being the result of machining processes or chemical attacks, is a key factor for the incorporation of advanced functionalities to a wide set of micro- and nanosystems. High-precision additive manufacturing (AM) technologies based on photopolymerization, together with the use of fractal models linked to computer-aided design tools, allow for a precise definit...

  20. Adaptive Process Controls and Ultrasonics for High Temperature PEM MEA Manufacture

    Energy Technology Data Exchange (ETDEWEB)

    Walczyk, Daniel F. [Rensselaer Polytechnic Inst., Troy, NY (United States)

    2015-08-26

    The purpose of this 5-year DOE-sponsored project was to address major process bottlenecks associated with fuel cell manufacturing. New technologies were developed to significantly reduce pressing cycle time for high temperature PEM membrane electrode assembly (MEA) through the use of novel, robust ultrasonic (U/S) bonding processes along with low temperature (<100°C) PEM MEAs. In addition, greater manufacturing uniformity and performance was achieved through (a) an investigation into the causes of excessive variation in ultrasonically and thermally bonded MEAs using more diagnostics applied during the entire fabrication and cell build process, and (b) development of rapid, yet simple quality control measurement techniques for use by industry.

  1. Weld distortion prediction and control of the ITER vacuum vessel manufacturing mock-ups

    International Nuclear Information System (INIS)

    Ottolini, Marco; Barbensi, Andrea

    2014-01-01

    The fabrication of the ITER Vacuum Vessel Sectors is an unprecedented challenge, due to their dimensions, the close tolerances, the complex 'D' shape. The technological issues were faced by the production of full scale mock ups to confirm the manufacturing feasibility to achieve very tight tolerances and qualify the main manufacturing processes, by a step by step welding distortion control, by the qualification of not conventional NDT inspection techniques and by innovative 3D dimensional inspections. The Supplier is required to fabricate at least two mock ups, inboard and outboard, related to the manufacturing method of the VV Sectors, to demonstrate the control of the welding distortions to achieve tolerances, optimizing welding sequences and calibrating of welding distortions computer simulations. The stages of this preparatory activity are: prediction of welding distortion for fabrication mock ups representative of selected segments; demonstration that distortion predictions are consistent with experimental results from 3D dimensional inspection; understanding of reasons of possible deviations between numerical and experimental results and definition of action to solve these issues; demonstration that possible calculation simplifications, adopted to speed up the analysis process, do not affect significantly the welding distortion prediction. This paper describes the weld distortion prediction and control on the manufacturing mock-ups of ITER Vacuum Vessel Sectors, with particular emphasis to the lessons learned. (authors)

  2. Controlling organic chemical hazards in food manufacturing: a hazard analysis critical control points (HACCP) approach.

    Science.gov (United States)

    Ropkins, K; Beck, A J

    2002-08-01

    Hazard analysis by critical control points (HACCP) is a systematic approach to the identification, assessment and control of hazards. Effective HACCP requires the consideration of all hazards, i.e., chemical, microbiological and physical. However, to-date most 'in-place' HACCP procedures have tended to focus on the control of microbiological and physical food hazards. In general, the chemical component of HACCP procedures is either ignored or limited to applied chemicals, e.g., food additives and pesticides. In this paper we discuss the application of HACCP to a broader range of chemical hazards, using organic chemical contaminants as examples, and the problems that are likely to arise in the food manufacturing sector. Chemical HACCP procedures are likely to result in many of the advantages previously identified for microbiological HACCP procedures: more effective, efficient and economical than conventional end-point-testing methods. However, the high costs of analytical monitoring of chemical contaminants and a limited understanding of formulation and process optimisation as means of controlling chemical contamination of foods are likely to prevent chemical HACCP becoming as effective as microbiological HACCP.

  3. PLAT: An Automated Fault and Behavioural Anomaly Detection Tool for PLC Controlled Manufacturing Systems.

    Science.gov (United States)

    Ghosh, Arup; Qin, Shiming; Lee, Jooyeoun; Wang, Gi-Nam

    2016-01-01

    Operational faults and behavioural anomalies associated with PLC control processes take place often in a manufacturing system. Real time identification of these operational faults and behavioural anomalies is necessary in the manufacturing industry. In this paper, we present an automated tool, called PLC Log-Data Analysis Tool (PLAT) that can detect them by using log-data records of the PLC signals. PLAT automatically creates a nominal model of the PLC control process and employs a novel hash table based indexing and searching scheme to satisfy those purposes. Our experiments show that PLAT is significantly fast, provides real time identification of operational faults and behavioural anomalies, and can execute within a small memory footprint. In addition, PLAT can easily handle a large manufacturing system with a reasonable computing configuration and can be installed in parallel to the data logging system to identify operational faults and behavioural anomalies effectively.

  4. PLAT: An Automated Fault and Behavioural Anomaly Detection Tool for PLC Controlled Manufacturing Systems

    Directory of Open Access Journals (Sweden)

    Arup Ghosh

    2016-01-01

    Full Text Available Operational faults and behavioural anomalies associated with PLC control processes take place often in a manufacturing system. Real time identification of these operational faults and behavioural anomalies is necessary in the manufacturing industry. In this paper, we present an automated tool, called PLC Log-Data Analysis Tool (PLAT that can detect them by using log-data records of the PLC signals. PLAT automatically creates a nominal model of the PLC control process and employs a novel hash table based indexing and searching scheme to satisfy those purposes. Our experiments show that PLAT is significantly fast, provides real time identification of operational faults and behavioural anomalies, and can execute within a small memory footprint. In addition, PLAT can easily handle a large manufacturing system with a reasonable computing configuration and can be installed in parallel to the data logging system to identify operational faults and behavioural anomalies effectively.

  5. EXPLORING LINKAGES BETWEEN MANUFACTURING FUNCTIONS, OPERATIONS PRIORITIES AND PLANT PERFORMANCE IN MANUFACTURING SMES IN MUMBAI

    Directory of Open Access Journals (Sweden)

    B.E. Narkhede

    2012-03-01

    Full Text Available Nowadays, in order for small and medium scale enterprises to excel in performance, it is necessary to have congruency among the manufacturing functions and the operational priorities. In this paper a model is presented to know the relationship between the manufacturing functions, operation priorities and manufacturing performance. Using data collected from small and medium scale manufacturing enterprises in Mumbai and suburban region, this study examines the seven hypothesis based on the relationship between manufacturing functions, priorities and perfomance. The structural equation model is tested using Amos7 software to test the hypothesis. The results show that there exists a positive relation between manufacturing functions and operation priorities as four out of six the dimensions measured such as Process control and implementation, Management of resources, Management of people, and Partnership with supplier are positively related, while two dimensions Training and developing and Teamwork are not positively related. Findings also support strong impact of operation priorities with growth in productivity as a measure of performance.

  6. 76 FR 17968 - Manufacturer of Controlled Substances; Notice of Registration

    Science.gov (United States)

    2011-03-31

    ... 1, 2010, (75 FR 53720), Austin Pharma LLC., 811 Paloma Drive, Suite A, Round Rock, Texas 78665-2402...) and determined that the registration of Austin Pharma LLC. to manufacture the listed basic classes of controlled substances is consistent with the public interest at this time. DEA has investigated Austin Pharma...

  7. 77 FR 2324 - Manufacturer of Controlled Substances; Notice of Registration

    Science.gov (United States)

    2012-01-17

    ..., 2011, 76 FR 51401, Austin Pharma LLC., 811 Paloma Drive, Suite C, Round Rock, Texas 78665-2402, made...) and determined that the registration of Austin Pharma LLC. to manufacture the listed basic classes of controlled substances is consistent with the public interest at this time. DEA has investigated Austin Pharma...

  8. 77 FR 30327 - Manufacturer of Controlled Substances; Notice Of Application; Research Triangle Institute

    Science.gov (United States)

    2012-05-22

    ... the following basic classes of controlled substances: Drug Schedule Marihuana (7360) I Cocaine (9041) II The Institute will manufacture marihuana, and cocaine derivatives for use by their customers in...

  9. 77 FR 75670 - Manufacturer of Controlled Substances, Notice of Registration, AMRI Rensselaer, Inc.

    Science.gov (United States)

    2012-12-21

    ... bulk manufacturer of the following basic classes of controlled substances: Drug Schedule Marihuana... development and for distribution to its customers. In reference to drug code 7360 (Marihuana), the company...

  10. 77 FR 55504 - Manufacturer of Controlled Substances; Notice of Registration; Research Triangle Institute

    Science.gov (United States)

    2012-09-10

    ... classes of controlled substances: Drug Schedule Marihuana (7360) I Cocaine (9041) II The Institute will manufacture marihuana, and cocaine derivatives for use by their customers in analytical kits, reagents, and...

  11. The need for artificial intelligence as an aid in controlling a manufacturing operation

    Science.gov (United States)

    Weyand, J.

    AI applications to industrial production and planning are discussed and illustrated with diagrams and drawings. Applications examined include flexible automation of manufacturing processes (robots with open manual control, robots programmable to meet product specifications, self-regulated robots, and robots capable of learning), flexible fault detection and diagnostics, production control, and overall planning and management (product strategies, marketing, determination of development capacity, site selection, project organization, and technology investment strategies). For the case of robots, problems in the design and operation of a state-of-the-art machine-tool cell (for hole boring, milling, and joining) are analyzed in detail.

  12. Shop Floor-Level Control of Manufacturing Companies: An Interview Study in Finland

    Directory of Open Access Journals (Sweden)

    Tokola Henri

    2015-02-01

    Full Text Available This paper publishes the results of interviews regarding shop-floor-level control of 18 Finnish manufacturing companies. The interviews had 17 open questions relating to demand characteristics, shop floor-level control issues, production flexibility, inventory control, and potential development areas. In order to get insights from the interviews, this paper analyses the answers from the interviews and categorises them into typical answers. The companies that were interviewed are also categorised as small companies with their own end products, subcontractors, or large companies with their own end products, and the emphasis of the analysis is on how companies differ in their shop floor-level control. The results show that different types of companies have different characteristics. Small companies are characterised by constant workflow, seasonal trends in demand, and the use of forecasts. Subcontractors have great daily variation in their demand and processing times. Large companies tend to focus on inventory issues.

  13. 78 FR 23959 - Manufacturer of Controlled Substances; Notice of Registration; PCAS-Nanosyn, LLC

    Science.gov (United States)

    2013-04-23

    ... request of the company's customers, it manufactures derivatives of controlled substances in bulk form only... compliance with state and local laws, and a review of the company's background and history. Therefore...

  14. 77 FR 31390 - Manufacturer of Controlled Substances; Notice of Registration; Pcas-Nanosyn, LLC

    Science.gov (United States)

    2012-05-25

    ... request of the company's customers, it manufactures derivatives of controlled substances in bulk form only... compliance with state and local laws, and a review of the company's background and history. Therefore...

  15. 'Serial review on clinical PET tracers'. Manufacturing and quality control of positron emitting radiopharmaceuticals produced by in-house cyclotron

    International Nuclear Information System (INIS)

    Saji, Hideo

    2009-01-01

    In order to establish PET diagnosis as a routine clinical tool, manufacture's compliance with regulations under the Good Manufacturing Practice (GMP) principle for PET radiopharmaceuticals is necessary. For this purpose, the Sub-committee on Medical Application of Positron Emitting Radionuclides, Medical Science and Pharmaceutical Committee of Japan Radioisotopes Association has proposed 'Standards for Compounds Labeled with Emitting Radionuclides Approved as Established Techniques for Medical Use'. This guideline includes the general notices, general rules for preparations, general tests for the quality control, quality of each PET agents, guideline for manufacturing environment and manufacturing process at manufacturing facilities of PET agents. Each facility should have a committee and establish an internal system to account for manufacturing compounds labeled with positron emitting radionuclides produced in the facility, and compile standards by referring to the 'Established Standard Techniques of Labeling Compounds with Emitting Radionuclides for use as Radiopharmaceuticals: approved by the Subcommittee on Medical Application of Cyclotron-Produced Radionuclides (revised in 2009)', in order to maintain the quality of radiopharmaceuticals. (author)

  16. Applications of dimensional micro metrology to the product and process quality control in manufacturing of precision polymer micro components

    DEFF Research Database (Denmark)

    Tosello, Guido; Hansen, Hans Nørgaard; Gasparin, Stefania

    2009-01-01

    Precision manufacturing of micro injection moulded (mu IM) components presents challenges in terms of quality control due to the miniaturization of product dimensions and tolerances. This paper addresses product compliance with specifications, focusing on tolerances of dimensions and position on mu...... IM components selected from industrial production. Two systems were analysed: a tactile coordinate measuring machine (CMM) with sub-micrometer uncertainty and an optical CMM allowing fast measurements suitable for in-line quality control. Product quality control capability, measuring uncertainty...... and calibration guidelines are discussed for both systems. Finally, a new approach for the manufacturing of hybrid micro polymer-metal calibrated objects is proposed....

  17. Design and Manufacturing of Remote Control for Children Viewing Using Children Inspiration

    OpenAIRE

    Madani, R.; Moroz, Adam

    2012-01-01

    N/A The recruitment of children’s imagination in the development of new product design provides an interesting source of new ideas for product development, including for products for children. This study is related to the design and manufacture of a prototype for a remote control that controls television viewing content for children, to protect them from inappropriate content, control their viewing time and keep them at a safe distance from the television screen. For security reasons this ...

  18. Flexibility in fuel manufacturing

    International Nuclear Information System (INIS)

    Reparaz, A.; Stavig, W.E.; McLees, R.B.

    1987-01-01

    From its inception Exxon Nuclear has produced both BWR and PWR fuels. This is reflected in a product line that, to date, includes over 20 fuel designs. These range from 6x6 design at one end of the spectrum to the recently introduced 17x17 design. The benefits offered include close tailoring of the fuel design to match the customer's requirements, and the ability to rapidly introduce product changes, such as the axial blanket design, with a minimal impact on manufacturing. This flexibility places a number of demands on the manufacturing organization. Close interfaces must be established, and maintained, between the marketing, product design, manufacturing, purchasing and quality organizations, and the information flows must be immediate and accurate. Production schedules must be well planned and must be maintained or revised to reflect changing circumstances. Finally, the manufacturing facilities must be designed to allow rapid switchover between product designs with minor tooling changes and/or rerouting of product flows to alternate work stations. Among the tools used to manage the flow of information and to maintain the tight integration necessary between the various manufacturing, engineering and quality organizations is a commercially available, computerized planning and tracking system, AMAPS. A real-time production data collection system has been designed which gathers data from each production work station for use by the shop floor control module of AMAPS. Accuracy of input to the system is improved through extensive use of bar codes to gather information on the product as it moves through and between work stations. This computerized preparation of material tracing has an impact on direct manufacturing records, quality control records, nuclear material records and accounting and inventory records. This is of benefit to both Exxon Nuclear and its customers

  19. 78 FR 5501 - Manufacturer of Controlled Substances; Notice of Registration; Cerilliant Corporation

    Science.gov (United States)

    2013-01-25

    ... DEPARTMENT OF JUSTICE Drug Enforcement Administration Manufacturer of Controlled Substances; Notice of Registration; Cerilliant Corporation By Notice dated August 17, 2012, and published in the Federal Register on August 29, 2012, 77 FR 52366, Cerilliant Corporation, 811 Paloma Drive, Suite A, Round...

  20. 77 FR 40087 - Manufacturer of Controlled Substances; Notice of Registration; Cerilliant Corporation

    Science.gov (United States)

    2012-07-06

    ... DEPARTMENT OF JUSTICE Drug Enforcement Administration Manufacturer of Controlled Substances; Notice of Registration; Cerilliant Corporation By Notice dated March 23, 2012, and published in the Federal Register on April 2, 2012, 77 FR 19717, Cerilliant Corporation, 811 Paloma Drive, Suite A, Round...

  1. 78 FR 33442 - Manufacturer of Controlled Substances; Notice of Registration; Cerilliant Corporation

    Science.gov (United States)

    2013-06-04

    ... DEPARTMENT OF JUSTICE Drug Enforcement Administration Manufacturer of Controlled Substances; Notice of Registration; Cerilliant Corporation By Notice dated January 14, 2013, and published in the Federal Register on January 25, 2013, 78 FR 5499, Cerilliant Corporation, 811 Paloma Drive, Suite A, Round...

  2. 77 FR 24987 - Manufacturer of Controlled Substances; Notice of Registration; Cerilliant Corporation

    Science.gov (United States)

    2012-04-26

    ... DEPARTMENT OF JUSTICE Drug Enforcement Administration Manufacturer of Controlled Substances; Notice of Registration; Cerilliant Corporation By Notice dated January 5, 2012, and published in the Federal Register on January 17, 2012, 77 FR 2321, Cerilliant Corporation, 811 Paloma Drive, Suite A, Round...

  3. Economic benefits of metrology in manufacturing

    DEFF Research Database (Denmark)

    Savio, Enrico; De Chiffre, Leonardo; Carmignato, S.

    2016-01-01

    examples from industrial production, in which the added value of metrology in manufacturing is discussed and quantified. Case studies include: general manufacturing, forging, machining, and related metrology. The focus of the paper is on the improved effectiveness of metrology when used at product...... and process design stages, as well as on the improved accuracy and efficiency of manufacturing through better measuring equipment and process chains with integrated metrology for process control.......In streamlined manufacturing systems, the added value of inspection activities is often questioned, and metrology in particular is sometimes considered only as an avoidable expense. Documented quantification of economic benefits of metrology is generally not available. This work presents concrete...

  4. Automation system for quality control in manufacture of iodine-125 sealed sources used in brachytherapy

    International Nuclear Information System (INIS)

    Somessari, Samir L.; Feher, Anselmo; Sprenger, Francisco E.; Rostellato, Maria E.C.M.; Moura, Joao A.; Costa, Osvaldo L.; Calvo, Wilson A.P.

    2011-01-01

    The objective of this work is to develop an automation system for Quality Control in the production of Iodine-125 sealed sources, after undergoing the process of laser beam welding. These sources, also known as Iodine-125 seeds are used, successfully, in the treatment of cancer by brachytherapy, with low-dose rates. Each small seed is composed of a welded titanium capsule with 0.8 mm diameter and 4.5 mm in length, containing Iodine-125 adsorbed on an internal silver wire. The seeds are implanted in the human prostate to irradiate the tumor and treat the cancerous cells. The technology to automate the quality control system in the manufacture of Iodine-125 seeds consists in developing and associate mechanical parts, electronic components and pneumatic circuits to control machines and processes. The automation technology for Iodine-125 seed production developed in this work employs programmable logic controller, step motors, drivers of control, electrical-electronic interfaces, photoelectric sensors, interfaces of communication and software development. Industrial automation plays an important role in the production of Iodine-125 seeds, with higher productivity and high standard of quality, facilitating the implementation and operation of processes with good manufacturing practices. Nowadays, the Radiation Technology Center at IPEN-CNEN/SP imports and distributes 36,000 Iodine-125 seeds per year for clinics and hospitals in the whole country. However, the Brazilian potential market is of 8,000 Iodine-125 seeds per month. Therefore, the local production of these radioactive seeds has become a priority for the Institute, aiming to reduce the price and increase the supply to the population in Brazil. (author)

  5. Automation system for quality control in manufacture of iodine-125 sealed sources used in brachytherapy

    Energy Technology Data Exchange (ETDEWEB)

    Somessari, Samir L.; Feher, Anselmo; Sprenger, Francisco E.; Rostellato, Maria E.C.M.; Moura, Joao A.; Costa, Osvaldo L.; Calvo, Wilson A.P., E-mail: somessar@ipen.b, E-mail: afeher@ipen.b, E-mail: sprenger@ipen.b, E-mail: elisaros@ipen.b, E-mail: olcosta@ipen.b, E-mail: wapcalvo@ipen.b [Instituto de Pesquisas Energeticas e Nucleares (IPEN/CNEN-SP), Sao Paulo, SP (Brazil)

    2011-07-01

    The objective of this work is to develop an automation system for Quality Control in the production of Iodine-125 sealed sources, after undergoing the process of laser beam welding. These sources, also known as Iodine-125 seeds are used, successfully, in the treatment of cancer by brachytherapy, with low-dose rates. Each small seed is composed of a welded titanium capsule with 0.8 mm diameter and 4.5 mm in length, containing Iodine-125 adsorbed on an internal silver wire. The seeds are implanted in the human prostate to irradiate the tumor and treat the cancerous cells. The technology to automate the quality control system in the manufacture of Iodine-125 seeds consists in developing and associate mechanical parts, electronic components and pneumatic circuits to control machines and processes. The automation technology for Iodine-125 seed production developed in this work employs programmable logic controller, step motors, drivers of control, electrical-electronic interfaces, photoelectric sensors, interfaces of communication and software development. Industrial automation plays an important role in the production of Iodine-125 seeds, with higher productivity and high standard of quality, facilitating the implementation and operation of processes with good manufacturing practices. Nowadays, the Radiation Technology Center at IPEN-CNEN/SP imports and distributes 36,000 Iodine-125 seeds per year for clinics and hospitals in the whole country. However, the Brazilian potential market is of 8,000 Iodine-125 seeds per month. Therefore, the local production of these radioactive seeds has become a priority for the Institute, aiming to reduce the price and increase the supply to the population in Brazil. (author)

  6. 78 FR 64021 - Manufacturer of Controlled Substances; Notice of Registration; Chemtos, LLC

    Science.gov (United States)

    2013-10-25

    ... DEPARTMENT OF JUSTICE Drug Enforcement Administration Manufacturer of Controlled Substances; Notice of Registration; Chemtos, LLC By Notice dated June 18, 2013, and published in the Federal Register on July 1, 2013, 78 FR 39340, Chemtos, LLC., 14101 W. Highway 290, Building 2000B, Austin, Texas...

  7. 77 FR 75671 - Manufacturer of Controlled Substances; Notice of Registration; Chemtos, LLC

    Science.gov (United States)

    2012-12-21

    ... DEPARTMENT OF JUSTICE Drug Enforcement Administration Manufacturer of Controlled Substances; Notice of Registration; Chemtos, LLC By Notice dated July 30, 2012, and published in the Federal Register on August 7, 2012, 77 FR 47116, Chemtos, LLC, 14101 W. Highway 290, Building 2000B, Austin, Texas...

  8. Robotics in space-age manufacturing

    Science.gov (United States)

    Jones, Chip

    1991-01-01

    Robotics technologies are developed to improve manufacturing of space hardware. The following applications of robotics are covered: (1) welding for the space shuttle and space station Freedom programs; (2) manipulation of high-pressure water for shuttle solid rocket booster refurbishment; (3) automating the application of insulation materials; (4) precision application of sealants; and (5) automation of inspection procedures. Commercial robots are used for these development programs, but they are teamed with advanced sensors, process controls, and computer simulation to form highly productive manufacturing systems. Many of the technologies are also being actively pursued in private sector manufacturing operations.

  9. Medição e controle do tempo de atravessamento em um sistema de manufatura Measurement and control of lead-time in a manufacturing system

    Directory of Open Access Journals (Sweden)

    Miguel Afonso Sellitto

    2008-04-01

    Full Text Available Este artigo apresenta um método para a medição do tempo de atravessamento e do inventário em processo em manufatura. A medição foi usada em processo de controle organizacional de manufatura, cuja variável controlada foi o tempo de atravessamento de ordens. Tal controle pode ser útil em estratégias de manufatura em que a competição é baseada no uso do tempo, a TBC (time-based competition. Apresentou-se o método de medição, que inclui elementos da teoria das filas, e considerações para a simplificação de arranjos produtivos de manufatura. Para testar e refinar o método, estudou-se um caso em manufatura calçadista. Foram coletados dados de remessas e obtido, por análise estatística e simulação computacional, o comportamento da variável aleatória tempo de atravessamento de remessas. Como a medição foi inferior ao objetivo de desempenho, partiu-se para o controle, fazendo um diagnóstico que apontou efeitos indesejáveis observados que foram endereçados por ações corretivas implementadas. Para verificar a eficácia das ações, nova coleta foi feita. Desta vez, o objetivo de desempenho das entregas foi atendido, fechando um ciclo de controle. Os resultados foram discutidos, chegando-se a conclusões e alternativas de continuidade.This paper presents a method for the measurement of the lead-time and work-in-process in manufacturing. The measurement was used in an organizational control process in manufacturing, in which the controlled variate was the order lead-time. This kind of control can be useful in manufacture strategies formulated to compete in TBC (time-based competition. We presented the method, who includes elements from the queuing theory, and concerns about simplifying complex manufacturing arrays, in order to facilitate the analysis. In order to test and refine the method, we studied a case in a footwear manufacture system. We collected data from orders and, by statistical techniques and computational

  10. Spatially Controlled Delivery of siRNAs to Stem Cells in Implants Generated by Multi-Component Additive Manufacturing

    DEFF Research Database (Denmark)

    Andersen, Morten Østergaard; Le, Dang Quang Svend; Chen, Muwan

    2013-01-01

    Additive manufacturing is a promising technique in tissue engineering, as it enables truly individualized implants to be made to fit a particular defect. As previously shown, a feasible strategy to produce complex multicellular tissues is to deposit different small interfering RNA (siRNA) in porous...... implants that are subsequently sutured together. In this study, an additive manufacturing strategy to deposit carbohydrate hydrogels containing different siRNAs is applied into an implant, in a spatially controlled manner. When the obtained structures are seeded with mesenchymal stem (stromal) cells......, the selected siRNAs are delivered to the cells and induces specific and localized gene silencing. Here, it is demonstrated how to replicate part of a patient's spinal cord from a computed tomography scan, using an additive manufacturing technique to produce an implant with compartmentalized si...

  11. Experience with quality assurance in fuel design and manufacturing

    International Nuclear Information System (INIS)

    Holzer, R.; Nilson, F.

    1984-01-01

    The Quality Assurance/Quality Control activities for nuclear fuel design and manufacturing described here are coordinated under a common ''Quality Assurance System For Fuel Assemblies and Associated Core Components'' which regulates the QA-functions of the development, design and manufacturing of fuel assemblies independent of the organizational assignment of the contributing technical groups. Some essential characteristics of the system are shown, using examples from design control, procurement, manufacturing and qualification of special processes. The experience is very good, it allowed a flexible and well controlled implementation of design and manufacturing innovations and contributed to the overall good fuel behavior. (orig.)

  12. 76 FR 13629 - Draft Guidance for Industry on Chemistry, Manufacturing, and Controls Information-Fermentation...

    Science.gov (United States)

    2011-03-14

    ...] Draft Guidance for Industry on Chemistry, Manufacturing, and Controls Information--Fermentation-Derived... Controls (CMC) Information-- Fermentation-Derived Intermediates, Drug Substances, and Related Drug Products... documentation to submit to support the CMC information for fermentation-derived intermediates, drug substances...

  13. Fuel manufacture and quality control

    International Nuclear Information System (INIS)

    Roepenack, H.; Raab, K.

    1975-01-01

    The different steps in fuel and fuel element manufacturing from the conversion of UF 6 to UO 2 to the assembling of the whole fuel element are shortly described. Each of this fabrication steps must satisfy well-defined quality criteria which are checked in certain analyses or tests. (RB) [de

  14. System-wide hybrid MPC-PID control of a continuous pharmaceutical tablet manufacturing process via direct compaction.

    Science.gov (United States)

    Singh, Ravendra; Ierapetritou, Marianthi; Ramachandran, Rohit

    2013-11-01

    The next generation of QbD based pharmaceutical products will be manufactured through continuous processing. This will allow the integration of online/inline monitoring tools, coupled with an efficient advanced model-based feedback control systems, to achieve precise control of process variables, so that the predefined product quality can be achieved consistently. The direct compaction process considered in this study is highly interactive and involves time delays for a number of process variables due to sensor placements, process equipment dimensions, and the flow characteristics of the solid material. A simple feedback regulatory control system (e.g., PI(D)) by itself may not be sufficient to achieve the tight process control that is mandated by regulatory authorities. The process presented herein comprises of coupled dynamics involving slow and fast responses, indicating the requirement of a hybrid control scheme such as a combined MPC-PID control scheme. In this manuscript, an efficient system-wide hybrid control strategy for an integrated continuous pharmaceutical tablet manufacturing process via direct compaction has been designed. The designed control system is a hybrid scheme of MPC-PID control. An effective controller parameter tuning strategy involving an ITAE method coupled with an optimization strategy has been used for tuning of both MPC and PID parameters. The designed hybrid control system has been implemented in a first-principles model-based flowsheet that was simulated in gPROMS (Process System Enterprise). Results demonstrate enhanced performance of critical quality attributes (CQAs) under the hybrid control scheme compared to only PID or MPC control schemes, illustrating the potential of a hybrid control scheme in improving pharmaceutical manufacturing operations. Copyright © 2013 Elsevier B.V. All rights reserved.

  15. Five-Axis Ultrasonic Additive Manufacturing for Nuclear Component Manufacture

    Science.gov (United States)

    Hehr, Adam; Wenning, Justin; Terrani, Kurt; Babu, Sudarsanam Suresh; Norfolk, Mark

    2017-03-01

    Ultrasonic additive manufacturing (UAM) is a three-dimensional metal printing technology which uses high-frequency vibrations to scrub and weld together both similar and dissimilar metal foils. There is no melting in the process and no special atmosphere requirements are needed. Consequently, dissimilar metals can be joined with little to no intermetallic compound formation, and large components can be manufactured. These attributes have the potential to transform manufacturing of nuclear reactor core components such as control elements for the High Flux Isotope Reactor at Oak Ridge National Laboratory. These components are hybrid structures consisting of an outer cladding layer in contact with the coolant with neutron-absorbing materials inside, such as neutron poisons for reactor control purposes. UAM systems are built into a computer numerical control (CNC) framework to utilize intermittent subtractive processes. These subtractive processes are used to introduce internal features as the component is being built and for net shaping. The CNC framework is also used for controlling the motion of the welding operation. It is demonstrated here that curved components with embedded features can be produced using a five-axis code for the welder for the first time.

  16. Chemistry, manufacturing and control (CMC) and clinical trial technical support for influenza vaccine manufacturers.

    Science.gov (United States)

    Wahid, Rahnuma; Holt, Renee; Hjorth, Richard; Berlanda Scorza, Francesco

    2016-10-26

    With the support of the Biomedical Advanced Research and Development Authority (BARDA) of the US Department of Health and Human Services, PATH has contributed to the World Health Organization's (WHO's) Global Action Plan for Influenza Vaccines (GAP) by providing technical and clinical assistance to several developing country vaccine manufacturers (DCVMs). GAP builds regionally based independent and sustainable influenza vaccine production capacity to mitigate the overall global shortage of influenza vaccines. The program also ensures adequate influenza vaccine manufacturing capacity in the event of an influenza pandemic. Since 2009, PATH has worked closely with two DCVMs in Vietnam: the Institute of Vaccines and Medical Biologicals (IVAC) and VABIOTECH. Beginning in 2013, PATH also began working with Torlak Institute in Serbia; Instituto Butantan in Brazil; Serum Institute of India Private Ltd. in India; and Changchun BCHT Biotechnology Co. (BCHT) in China. The DCVMs supported under the GAP program all had existing influenza vaccine manufacturing capability and required technical support from PATH to improve vaccine yield, process efficiency, and product formulation. PATH has provided customized technical support for the manufacturing process to each DCVM based on their respective requirements. Additionally, PATH, working with BARDA and WHO, supported several DCVMs in the clinical development of influenza vaccine candidates progressing toward national licensure or WHO prequalification. As a result of the activities outlined in this review, several companies were able to make excellent progress in developing state-of-the-art manufacturing processes and completing early phase clinical trials. Licensure trials are currently ongoing or planned for several DCVMs. Copyright © 2016 Elsevier Ltd. All rights reserved.

  17. Service orientation in holonic and multi-agent manufacturing

    CERN Document Server

    Thomas, André; Trentesaux, Damien

    2015-01-01

    This volume gathers the peer reviewed papers presented at the 4th edition of the International Workshop “Service Orientation in Holonic and Multi-agent Manufacturing – SOHOMA’14” organized and hosted on November 5-6, 2014 by the University of Lorraine, France in collaboration with the CIMR Research Centre of the University Politehnica of Bucharest and the TEMPO Laboratory of the University of Valenciennes and Hainaut-Cambrésis.   The book is structured in six parts, each one covering a specific research line which represents a trend in future manufacturing: (1) Holonic and Agent-based Industrial Automation Systems; (2) Service-oriented Management and Control of Manufacturing Systems; (3) Distributed Modelling for Safety and Security in Industrial Systems; (4) Complexity, Big Data and Virtualization in Computing-oriented Manufacturing; (5) Adaptive, Bio-inspired and Self-organizing Multi-Agent Systems for Manufacturing, and (6) Physical Internet Simulation, Modelling and Control.   There is a clear ...

  18. Simulation Environment Synchronizing Real Equipment for Manufacturing Cell

    Science.gov (United States)

    Inukai, Toshihiro; Hibino, Hironori; Fukuda, Yoshiro

    Recently, manufacturing industries face various problems such as shorter product life cycle, more diversified customer needs. In this situation, it is very important to reduce lead-time of manufacturing system constructions. At the manufacturing system implementation stage, it is important to make and evaluate facility control programs for a manufacturing cell, such as ladder programs for programmable logical controllers (PLCs) rapidly. However, before the manufacturing systems are implemented, methods to evaluate the facility control programs for the equipment while mixing and synchronizing real equipment and virtual factory models on the computers have not been developed. This difficulty is caused by the complexity of the manufacturing system composed of a great variety of equipment, and stopped precise and rapid support of a manufacturing engineering process. In this paper, a manufacturing engineering environment (MEE) to support manufacturing engineering processes using simulation technologies is proposed. MEE consists of a manufacturing cell simulation environment (MCSE) and a distributed simulation environment (DSE). MCSE, which consists of a manufacturing cell simulator and a soft-wiring system, is emphatically proposed in detail. MCSE realizes making and evaluating facility control programs by using virtual factory models on computers before manufacturing systems are implemented.

  19. 77 FR 47108 - Manufacturer of Controlled Substances; Notice of Application; Cerilliant Corporation

    Science.gov (United States)

    2012-08-07

    ... DEPARTMENT OF JUSTICE Drug Enforcement Administration Manufacturer of Controlled Substances; Notice of Application; Cerilliant Corporation Pursuant to Title 21 Code of Federal Regulations 1301.34 (a), this is notice that on July 6, 2012, Cerilliant Corporation, 811 Paloma Drive, Suite A, Round Rock...

  20. 77 FR 52366 - Manufacturer of Controlled Substances; Notice of Application; Cerilliant Corporation

    Science.gov (United States)

    2012-08-29

    ... DEPARTMENT OF JUSTICE Drug Enforcement Administration Manufacturer of Controlled Substances; Notice of Application; Cerilliant Corporation Pursuant to Sec. 1301.33(a), Title 21 of the Code of Federal Regulations (CFR), this is notice that on July 16, 2012, Cerilliant Corporation, 811 Paloma Drive...

  1. 78 FR 54917 - Manufacturer of Controlled Substances; Notice of Application; Cerilliant Corporation

    Science.gov (United States)

    2013-09-06

    ... DEPARTMENT OF JUSTICE Drug Enforcement Administration Manufacturer of Controlled Substances; Notice of Application; Cerilliant Corporation Pursuant to Sec. 1301.33(a), Title 21 of the Code of Federal Regulations (CFR), this is notice that on July 10, 2013, Cerilliant Corporation, 811 Paloma Drive...

  2. 78 FR 5499 - Manufacturer of Controlled Substances; Notice of Application; Cerilliant Corporation

    Science.gov (United States)

    2013-01-25

    ... DEPARTMENT OF JUSTICE Drug Enforcement Administration Manufacturer of Controlled Substances; Notice of Application; Cerilliant Corporation Pursuant to Sec. 1301.33(a), Title 21 of the Code of Federal Regulations (CFR), this is notice that on October 4, 2012, Cerilliant Corporation, 811 Paloma...

  3. 77 FR 19717 - Manufacturer of Controlled Substances; Notice of Application; Cerilliant Corporation

    Science.gov (United States)

    2012-04-02

    ... DEPARTMENT OF JUSTICE Drug Enforcement Administration Manufacturer of Controlled Substances; Notice of Application; Cerilliant Corporation Pursuant to Sec. 1301.33(a), Title 21 of the Code of Federal Regulations (CFR), this is notice that on February 17, 2012, Cerilliant Corporation, 811 Paloma...

  4. 6th Workshop on Service Orientation in Holonic and Multi-Agent Manufacturing

    CERN Document Server

    Trentesaux, Damien; Thomas, André; Leitão, Paulo; Oliveira, José

    2017-01-01

    The book offers an integrated vision on Cloud and HPC, Big Data, Analytics and virtualization in computing-oriented manufacturing, combining information and communication technologies, service-oriented control of holonic architectures as well as enterprise integration solutions based on SOA principles. It is structured in eight parts, each one grouping research and trends in digital manufacturing and service oriented manufacturing control: Cloud and Cyber-Physical Systems for Smart Manufacturing, Reconfigurable and Self-organized Multi-Agent Systems for Industry and Service, Sustainability Issues in Intelligent Manufacturing Systems, Holonic and Multi-agent System Design for Industry and Service, Should Intelligent Manufacturing Systems be Dependable and Safe?, Service-oriented Management and Control of Manufacturing Systems, Engineering and Human Integration in Flexible and Reconfigurable Industrial Systems,Virtualization and Simulation in Computing-oriented Industry and Service.

  5. 78 FR 15975 - Manufacturer of Controlled Substances, Notice of Registration; Johnson Matthey, Inc...

    Science.gov (United States)

    2013-03-13

    ..., Notice of Registration; Johnson Matthey, Inc., Pharmaceuticals Materials By Notice dated November 1, 2012, and published in the Federal Register on November 9, 2012, 77 FR 67397, Johnson Matthey, Inc...) II The company plans to manufacture the listed controlled substances in bulk for distribution and...

  6. ACE - Manufacturer Identification Code (MID)

    Data.gov (United States)

    Department of Homeland Security — The ACE Manufacturer Identification Code (MID) application is used to track and control identifications codes for manufacturers. A manufacturer is identified on an...

  7. 78 FR 32459 - Manufacturer of Controlled Substances; Notice of Registration; Mallinckrodt, LLC.

    Science.gov (United States)

    2013-05-30

    ... plans to manufacture the listed controlled substances for internal use and for sale to other companies... ensure that the company's registration is consistent with the public interest. The investigation has included inspection and testing of the company's physical security systems, verification of the company's...

  8. 78 FR 5500 - Manufacturer of Controlled Substances, Notice of Application; Siegfried (USA)

    Science.gov (United States)

    2013-01-25

    ... DEPARTMENT OF JUSTICE Drug Enforcement Administration Manufacturer of Controlled Substances, Notice of Application; Siegfried (USA) Pursuant to Sec. 1301.33(a), Title 21 of the Code of Federal Regulations (CFR), this is notice that on June 19, 2012, Siegfried (USA), 33 Industrial Park Road, Pennsville...

  9. 78 FR 64018 - Manufacturer of Controlled Substances; Notice of Application; GE Healthcare

    Science.gov (United States)

    2013-10-25

    ... DEPARTMENT OF JUSTICE Drug Enforcement Administration Manufacturer of Controlled Substances; Notice of Application; GE Healthcare Pursuant to Sec. 1301.33(a), Title 21 of the Code of Federal Regulations (CFR), this is notice that on September 12, 2013, GE Healthcare, 3350 North Ridge Avenue...

  10. 78 FR 12103 - Manufacturer of Controlled Substances; Notice of Application; GE Healthcare

    Science.gov (United States)

    2013-02-21

    ... DEPARTMENT OF JUSTICE Drug Enforcement Administration Manufacturer of Controlled Substances; Notice of Application; GE Healthcare Pursuant to Sec. 1301.33(a), Title 21 of the Code of Federal Regulations (CFR), this is notice that on August 31, 2012, GE Healthcare, 3350 North Ridge Avenue, Arlington...

  11. Assessing the interaction effect of cost control systems and information technology integration on manufacturing plant financial performance

    OpenAIRE

    Maiga, Adam S; Nilsson, Anders; Jacobs, Fred

    2014-01-01

    The interface between management control and information technology is an under-developed research area with a knowledge gap concerning its implications for financial performance. This study contributes to bridging this gap by investigates the interaction effect of cost control systems and information technology integration on manufacturing plant financial performance. We surveyed a sample of 518 managers of U.S. manufacturing plants, approximately evenly distributed between those using activ...

  12. 78 FR 24691 - Current Good Manufacturing Practice and Hazard Analysis and Risk-Based Preventive Controls for...

    Science.gov (United States)

    2013-04-26

    ... comments should be identified with the title ``Current Good Manufacturing Practice and Hazard Analysis and..., 114, 117, 120, 123, 129, 179, and 211 [Docket No. FDA-2011-N-0920] RIN 0910-AG36 Current Good Manufacturing Practice and Hazard Analysis and Risk- Based Preventive Controls for Human Food; Extension of...

  13. 77 FR 30028 - Manufacturer of Controlled Substances; Notice of Registration; Johnson Matthey, Inc...

    Science.gov (United States)

    2012-05-21

    ...; Notice of Registration; Johnson Matthey, Inc., Pharmaceuticals Materials By Notice dated January 6, 2012, and published in the Federal Register on January 17, 2012, 77 FR 2324, Johnson Matthey, Inc... (9333) II The company plans to manufacture the listed controlled substances in bulk for sale to its...

  14. 78 FR 19017 - Manufacturer of Controlled Substances; Notice of Application; Johnson Matthey Pharmaceutical...

    Science.gov (United States)

    2013-03-28

    ... DEPARTMENT OF JUSTICE Drug Enforcement Administration Manufacturer of Controlled Substances; Notice of Application; Johnson Matthey Pharmaceutical Materials, Inc. Pursuant to Sec. 1301.33(a), Title... Matthey Pharmaceutical Materials, Inc., Pharmaceutical Service, 25 Patton Road, Devens, Massachusetts...

  15. SISTEM PENDUKUNG KEPUTUSAN PENERIMAAN PESANAN MENGGUNAKAN LOAD ORIENTED MANUFACTURING CONTROL (LOMC

    Directory of Open Access Journals (Sweden)

    Deni Pandwinata

    2013-06-01

    Full Text Available CV. Grafika Inndah is a printing company, majoring in job order production system. While so far, the company has problems on the decision making due to lead time for booking orders that the company can accept customer orders according to quantity and due date. The production process of the design, print finishing and that includes the print engine 52 and engine Sakura print shop. The station receives a print job that exceeds the load capacity. Thus this research aims to determine the lead time, the average output and average utility. Data processing in this study using the method of manufacturing systems based load control (load oriented manufacturing control, and to assist in decision-making applications built using Delphi. Programming of the analysis of the data processing method known LOMC can the average lead time work station 2.88 hours and an average of 99.7% utilities, and Print Shop Lead time average of 1.82 hours and an average of 99.85% utilities. Decision support system applied in this study deserves to be implemented. It can be seen from the test program using the Black Box Test and Alpha Test is evidenced in respondents answered SS (strongly agree as much as 48% and S (agree as much as 46% .

  16. Taxonomies for Reasoning About Cyber-physical Attacks in IoT-based Manufacturing Systems

    Directory of Open Access Journals (Sweden)

    Yao Pan

    2017-03-01

    Full Text Available The Internet of Things (IoT has transformed many aspects of modern manufacturing, from design to production to quality control. In particular, IoT and digital manufacturing technologies have substantially accelerated product development- cycles and manufacturers can now create products of a complexity and precision not heretofore possible. New threats to supply chain security have arisen from connecting machines to the Internet and introducing complex IoT-based systems controlling manufacturing processes. By attacking these IoT-based manufacturing systems and tampering with digital files, attackers can manipulate physical characteristics of parts and change the dimensions, shapes, or mechanical properties of the parts, which can result in parts that fail in the field. These defects increase manufacturing costs and allow silent problems to occur only under certain loads that can threaten safety and/or lives. To understand potential dangers and protect manufacturing system safety, this paper presents two taxonomies: one for classifying cyber-physical attacks against manufacturing processes and another for quality control measures for counteracting these attacks. We systematically identify and classify possible cyber-physical attacks and connect the attacks with variations in manufacturing processes and quality control measures. Our taxonomies also provide a scheme for linking emerging IoT-based manufacturing system vulnerabilities to possible attacks and quality control measures.

  17. Microneedle Manufacture: Assessing Hazards and Control Measures

    Directory of Open Access Journals (Sweden)

    Alexander Martin

    2017-10-01

    Full Text Available Transdermal microneedles have captured the attention of researchers in relation to a variety of applications, and silicone-based moulds required to produce these systems are now widely available and can be readily manufactured on the lab bench. There is however some concern over the potential for accidental needlestick injuries and, as with any sharp hazard, the potential for blood-borne pathogen transmission must be considered. This follows from recent governmental concerns over the use of microneedle systems in dermabrasion. Despite the piercing nature of the microneedle patch sharing many similarities with conventional hypodermic needles, there are notable factors that mitigate the risk of contamination. A range of microneedle systems has been prepared using micromoulding techniques, and their puncture capability assessed. A critical assessment of the potential for accidental puncture and the control measures needed to ensure safe utilisation of the patch systems is presented.

  18. Mix-oriented manufacturing control (MOMC): a quasi-optimal procedure for dynamic scheduling control

    Science.gov (United States)

    Cristofari, Marco; Caron, Franco; McDuffie, Ernest L.

    1997-12-01

    The total system throughput (ST) is one of the most important decision variables at the planning/scheduling phase of a manufacturing system. Material requirement planning (MRP) and master production schedule (MPS) are based on the assumption that ST is known. All the subsequent developments (e.g. jobs- release, system work-load, input-product mix, etc.) depends on such an assumption. If this assumption is incorrect, the production activity control (PAC) will not be able to satisfy the planned targets during the scheduling phase. Delays and bottlenecks will be unavoidable in the system. In case of random flexible manufacturing system (FMS) (or, in general, job-shop production), the measure of ST can not be evaluated a priori without running simulations or observing the actual flow of the operations in the system. The way entities enter the system (sequencing and percentage of the input products) effects the value of ST in such a way that estimation based on historical data are highly risky. The methodology proposed in this paper allows the scheduler to assess the analytical functions which link ST, and other output performance variables, to the input product mix (IPM). This way the robustness of the scheduling plan can be verified before the actual release of the jobs into the system.

  19. 78 FR 5499 - Manufacturer of Controlled Substances; Notice of Registration; Johnson Matthey, Inc.

    Science.gov (United States)

    2013-01-25

    ...; Notice of Registration; Johnson Matthey, Inc. By Notice dated May 9, 2012, and published in the Federal Register on May 21, 2012, 77 FR 30026, Johnson Matthey, Inc., Custom Pharmaceuticals Department, 2003 Nolte... substance listed in schedule II. The company plans to manufacture the listed controlled substance for sale...

  20. International Workshop on Service Orientation in Holonic and Multi-Agent Manufacturing

    CERN Document Server

    Trentesaux, Damien; Thomas, André; McFarlane, Duncan

    2016-01-01

    This volume gathers the peer reviewed papers which were presented at the 5th edition of the International Workshop “Service Orientation in Holonic and Multi-agent Man-ufacturing – SOHOMA’15” organized in November 5-6, 2015 by the Institute for Manufacturing (IfM) of the University of Cambridge, UK in collaboration with the CIMR Research Centre in Computer Integrated Manufacturing and Robotics of the University Politehnica of Bucharest, Romania, the LAMIH Laboratory of Industrial and Human Automation Control, Mechanical Engineering and Computer Science of the University of Valenciennes and Hainaut-Cambrésis, France and the CRAN Re-search Centre for Automatic Control, Nancy of the University of Lorraine, France. The book is structured in seven parts, each one grouping a number of chapters de-scribing research in actual domains of the digital transformation in manufacturing and trends in future manufacturing control: (1) Applications of Intelligent Products; (2) Advances in Control of Physical Internet ...

  1. EERE Quality Control Workshop Final Report: Proceedings from the EERE Quality Control Workshop, in support of the DOE Clean Energy Manufacturing Initiative; Golden, Colorado, December 9-10, 2013

    Energy Technology Data Exchange (ETDEWEB)

    2014-05-01

    The U.S. Department of Energy Office of Energy Efficiency & Renewable Energy (EERE) has recognized the cross-cutting, pre-competitive and enabling nature of quality control for a wide range of clean energy technologies. As such, the Fuel Cell Technologies Office, Solar Energy Technologies Office, Vehicle Technologies Office, Building Technologies Office, and Advanced Manufacturing Office decided to explore needs and potential cross-office synergies in this area by holding the EERE Quality Control Workshop, in support of the DOE Clean Energy Manufacturing Initiative. This report summarizes the purpose and scope of the workshop; reviews the current status and state-of-the-art for in-line quality control; summarizes the results from three breakout sessions; and presents conclusions and recommendations.

  2. Cyber physical systems role in manufacturing technologies

    Science.gov (United States)

    Al-Ali, A. R.; Gupta, Ragini; Nabulsi, Ahmad Al

    2018-04-01

    Empowered by the recent development in single System-on-Chip, Internet of Things, and cloud computing technologies, cyber physical systems are evolving as a major controller during and post the manufacturing products process. In additional to their real physical space, cyber products nowadays have a virtual space. A product virtual space is a digital twin that is attached to it to enable manufacturers and their clients to better manufacture, monitor, maintain and operate it throughout its life time cycles, i.e. from the product manufacturing date, through operation and to the end of its lifespan. Each product is equipped with a tiny microcontroller that has a unique identification number, access code and WiFi conductivity to access it anytime and anywhere during its life cycle. This paper presents the cyber physical systems architecture and its role in manufacturing. Also, it highlights the role of Internet of Things and cloud computing in industrial manufacturing and factory automation.

  3. 77 FR 67397 - Manufacturer of Controlled Substances; Notice of Application; Johnson Matthey, Inc.

    Science.gov (United States)

    2012-11-09

    ...; Notice of Application; Johnson Matthey, Inc. Pursuant to Sec. 1301.33(a), Title 21 of the Code of Federal Regulations (CFR), this is notice that on September 10, 2012, Johnson Matthey, Inc., Pharmaceuticals Materials... Thebaine (9333) II The company plans to manufacture the listed controlled substances in bulk for...

  4. 77 FR 16264 - Manufacturer of Controlled Substances, Notice of Registration; Johnson Matthey Pharmaceutical...

    Science.gov (United States)

    2012-03-20

    ..., Notice of Registration; Johnson Matthey Pharmaceutical Materials Inc. By Notice dated November 18, 2011... Pharmaceutical Materials Inc., Pharmaceutical Service, 25 Patton Road, Devens, Massachusetts 01434, made... Matthey Pharmaceutical Materials Inc. to manufacture the listed basic classes of controlled substances is...

  5. Toward Meaningful Manufacturing Variation Data in Design - Feature Based Description of Variation in Manufacturing Processes

    DEFF Research Database (Denmark)

    Eifler, Tobias; Boorla, Srinivasa Murthy; Howard, Thomas J.

    2016-01-01

    The need to mitigate the effects of manufacturing variation already in design is nowadays commonly acknowledged and has led to a wide use of predictive modeling techniques, tolerancing approaches, etc. in industry. The trustworthiness of corresponding variation analyses is, however, not ensured...... by the availability of sophisticated methods and tools alone, but does evidently also depend on the accuracy of the input information used. As existing approaches for the description of manufacturing variation focus however, almost exclusively, on monitoring and controlling production processes, there is frequently...... a lack of objective variation data in design. As a result, variation analyses and tolerancing activities rely on numerous assumptions made to fill the gaps of missing or incomplete data. To overcome this hidden subjectivity, a schema for a consistent and standardised description of manufacturing...

  6. 77 FR 30026 - Manufacturer of Controlled Substances; Notice of Application; Johnson Matthey, Inc.

    Science.gov (United States)

    2012-05-21

    ...; Notice of Application; Johnson Matthey, Inc. Pursuant to Sec. 1301.33(a), Title 21 of the Code of Federal Regulations (CFR), this is notice that on March 26, 2012, Johnson Matthey, Inc., Custom Pharmaceuticals...), a basic class of controlled substance listed in schedule II. The company plans to manufacture the...

  7. 78 FR 64020 - Manufacturer of Controlled Substances; Notice of Registration; Siegfried USA, LLC

    Science.gov (United States)

    2013-10-25

    ...; Notice of Registration; Siegfried USA, LLC By Notice dated May 22, 2013, and published in the Federal Register on May 30, 2013, 78 FR 32458, Siegfried USA, LLC., 33 Industrial Park Road, Pennsville, New Jersey... determined that the registration of Siegfried USA, LLC., to manufacture the listed basic class of controlled...

  8. Open manufacturing system using MMS service and object oriented manufacturing equipment

    International Nuclear Information System (INIS)

    Kim, Dong Hoon; Song, Jun Yeob; Kim, Sun Ho

    2007-01-01

    Manufacturing equipment should be integrated to construct CIM (Computer Integrated Manufacturing) environment, but several economical and technological difficulties may be arisen in case heterogeneous systems are integrated into each other. MMS (Manufacturing Message Specification) can be effective in such a case, but the problem is that MMS-related products are comparatively expensive and the existing manufacturing equipment mostly do not support MMS. This study was focused on developing a gateway suitable to a non-MMS-compatible CNC machine-tool, and on implementing OSI (Open System Interconnection) upper layer on TCP/IP. The development system was applied to a cell controller by means of heterogeneous equipment under CIM environment, and to evaluate interoperability and portability

  9. Technological dispute for manufacturing population

    Directory of Open Access Journals (Sweden)

    B.M. Hevko

    2017-12-01

    Full Text Available New designs of technological equipment are presented – a variegated unit for adjusting the machine for precise manufacturing of a cut or on a tool of a tester, or on a workpiece, and also a design of a control device for measuring average diameters of taps. An important element in the manufacture of cutting tools is the manufacture of appropriate technological equipment. So for the manufacture of taps, it is necessary to develop the design of technological equipment for the adjustment of the necessary design parameters, as well as the design of control devices for their parameters. To provide these operations to instruments are the requirements of accuracy, productivity, stability, cost of production and a number of others. The new design of the technological equipment for the adjustment of the machine for precise manufacturing of the cutting is presented. The design of the control device for measuring the average diameter of the taps is also given. The advantages of the device include improving the quality of processing and working out the design on the technological.

  10. Quality assurance in tube manufacture

    International Nuclear Information System (INIS)

    Depken, H.

    1976-01-01

    Reliability in service essential for many high-technology products fabricated today. This is particularly the case within the nuclear industry. Here defective materials or components may have diastrous consequences to the safety of human beings and the environment. A new concept - Quality Assurance - originates from this industry. The concept implies that all contractors, fabricators and material manufactures involved must prove that the quality control system used, fulfits particular requirements at all manufacturing, inspection and testing stages. These requirement are laid down in two standards issued by the U.S. Atomic Energy Commission and the American Society of Mechanical Engineers. These standards are discussed in the paper. As a manufacturer of steel products for nuclear applications Sandvik has been forced to establish a quality assurance system according to these principles. The Sandvik approach is briefly described with regard to organisation and other major quality assurance activities. Further the education and training of operators and technicians is touched upon. Finally some viewpoints regarding audits performed by customers of steel manufacturers are expressed. (author)

  11. Utility of optical heterodyne displacement sensing and laser ultrasonics as in situ process control diagnostic for additive manufacturing

    Science.gov (United States)

    Manzo, Anthony J.; Helvajian, Henry

    2018-04-01

    An in situ process control monitor is presented by way of experimental results and simulations, which utilizes a pulsed laser ultrasonic source as a probe and an optical heterodyne displacement meter as a sensor. The intent is for a process control system that operates in near real time, is nonintrusive, and in situ: A necessary requirement for a serial manufacturing technology such as additive manufacturing (AM). We show that the diagnostic approach has utility in characterizing the local temperature, the area of the heat-affected zone, and the surface roughness (Ra ˜ 0.4 μm). We further demonstrate that it can be used to identify solitary defects (i.e., holes) on the order of 10 to 20 μm in diameter. Moreover, the technique shows promise in measuring properties of materials with features that have a small radius of curvature. We present results for a thin wire of ˜650 μm in diameter. By applying multiple pairs of probe-sensor systems, the diagnostic could also measure the local cooling rate on the scale of 1 μs. Finally, while an obvious application is used in AM technology, then all optical diagnostics could be applied to other manufacturing technologies.

  12. Modeling and Performance Analysis of Manufacturing Systems in ...

    African Journals Online (AJOL)

    Modeling and Performance Analysis of Manufacturing Systems in Footwear Industry. ... researcher to experiment with different variables and controls the manufacturing process ... In this study Arena simulation software is employed to model and measure ... for Authors · for Policy Makers · about Open Access · Journal Quality.

  13. SISTEM PENDUKUNG KEPUTUSAN PENERIMAAN PESANAN MENGGUNAKAN LOAD ORIENTED MANUFACTURING CONTROL (LOMC

    Directory of Open Access Journals (Sweden)

    Deni Pandwinata

    2013-06-01

    Full Text Available CV. Grafika Inndah is a printing company, majoring in job order production system. While so far, the company has problems on the decision making due to lead time for booking orders that the company can accept customer orders according to quantity and due date.  The production process of the design, print finishing and that includes the print engine 52 and engine Sakura print shop.  The station receives a print job that exceeds the load capacity. Thus this research aims to determine the lead time, the average output and average utility.  Data processing in this study using the method of manufacturing systems based load control (load oriented manufacturing control, and to assist in decision-making applications built using Delphi.  Programming of the analysis of the data processing method known LOMC can the average lead time work station 2.88 hours and an average of 99.7% utilities, and Print Shop Lead time average of 1.82 hours and an average of 99.85% utilities. Decision support system applied in this study deserves to be implemented.  It can be seen from the test program using the Black Box Test and Alpha Test is evidenced in respondents answered SS (strongly agree as much as 48% and S (agree as much as 46% .

  14. Towards the implementation of e-manufacturing: design of an automatic tea drying control system

    Directory of Open Access Journals (Sweden)

    Mabvuu, Never

    2014-11-01

    Full Text Available Many of the production costs for producing tea are attributable to the process of drying the tea. E-manufacturing can assist companies to reduce these production costs by making crucial information available to decision-makers so that they can make informed decisions. This paper presents an application of e-manufacturing to the design of an automatic tea drying control system. This control system will ensure that the multiple drying parameters such as temperature, dryer-exit tea moisture content, and fuel consumption are maintained at optimal states during the course of the drying of tea. The additional aim of this system is to balance the cost of production and the quality of the final product. Using the Guggenheim-Anderson-De Boer (GAB model, the optimum drying temperature was found to be 100-110°C, while maintaining a dryer-exit tea moisture content of 3 to 3.12 per cent, at a drying rate of 3 per cent per minute. A Barix control application to control the system’s activities, using the web user interface (WUI, was also developed.

  15. Applications of Fiber-Reinforced Polymers in Additive Manufacturing

    DEFF Research Database (Denmark)

    Hofstätter, Thomas; Pedersen, David Bue; Tosello, Guido

    2017-01-01

    Additive manufacturing technologies are these years entering the market of functional final parts. Initial research has been performed targeting the integration of fibers into additive manufactured plastic composites. Major advantages, among others, are for example increased tensile strength...... and Young's modulus. Key challenges in the field, as of now, are proper fiber placement, fiber seizing, an increased knowledge in the used materials and how they are applied into engineering solutions through proper control of the additive manufacturing process. The aim of this research is the improved...... understanding of fiber-reinforcement in additive manufacturing in terms of production and application. Vat polymerization and material extrusion techniques for composite additive manufacturing were investigated with respect of increasing adhesion between the matrix material and the fibers. Process optimization...

  16. 78 FR 51210 - Manufacturer of Controlled Substances; Notice of Application; Halo Pharmaceutical, Inc.

    Science.gov (United States)

    2013-08-20

    ... DEPARTMENT OF JUSTICE Drug Enforcement Administration Manufacturer of Controlled Substances; Notice of Application; Halo Pharmaceutical, Inc. Pursuant to Sec. 1301.33(a), Title 21 of the Code of Federal Regulations (CFR), this is notice that on July 8, 2013, Halo Pharmaceutical, Inc., 30 North...

  17. 77 FR 47114 - Manufacturer of Controlled Substances; Notice of Application; Halo Pharmaceutical Inc.

    Science.gov (United States)

    2012-08-07

    ... DEPARTMENT OF JUSTICE Drug Enforcement Administration Manufacturer of Controlled Substances; Notice of Application; Halo Pharmaceutical Inc. Pursuant to Sec. 1301.33(a), Title 21 of the Code of Federal Regulations (CFR), this is notice that on July 6, 2012, Halo Pharmaceutical Inc., 30 North...

  18. Manufacturing and control of the aspherical mirrors for the telescope of the satellite Pleiades

    Science.gov (United States)

    Ducollet, Hélène; du Jeu, Christian; Fermé, Jean-Jacques

    2017-11-01

    For the Pleiades space program, SESO has been awarded the contract (fully completed), for the manufacturing of the whole set of telescope mirrors (4 mirrors, 2 flight models). These works did also include the mechanical design, manufacturing and mounting of the attachment flexures between the mirrors and the telescope main structure. This presentation is focused on the different steps of lightweighting, polishing, integration and control of these mirrors as well as a presentation of the existing SESO facilities and capabilities to produce such kind of aspherical components/sub-assemblies.

  19. Metrology for Fuel Cell Manufacturing

    Energy Technology Data Exchange (ETDEWEB)

    Stocker, Michael [National Inst. of Standards and Technology, Gaithersburg, MD (United States); Stanfield, Eric [National Inst. of Standards and Technology, Gaithersburg, MD (United States)

    2015-02-04

    The project was divided into three subprojects. The first subproject is Fuel Cell Manufacturing Variability and Its Impact on Performance. The objective was to determine if flow field channel dimensional variability has an impact on fuel cell performance. The second subproject is Non-contact Sensor Evaluation for Bipolar Plate Manufacturing Process Control and Smart Assembly of Fuel Cell Stacks. The objective was to enable cost reduction in the manufacture of fuel cell plates by providing a rapid non-contact measurement system for in-line process control. The third subproject is Optical Scatterfield Metrology for Online Catalyst Coating Inspection of PEM Soft Goods. The objective was to evaluate the suitability of Optical Scatterfield Microscopy as a viable measurement tool for in situ process control of catalyst coatings.

  20. Manufacture and quality control of concrete for Ikata Nuclear Power Station, Shikoku Electric Power Co., Inc

    International Nuclear Information System (INIS)

    Tada, Akiomi; Kitada, Takao

    1989-01-01

    Ikata Nuclear Power Station, only one nuclear power station in Shikoku, is located at the root of Sada Peninsula on Seto Inland sea side. At present, No.1 and No.2 plants of 566 MW each are in commercial operation, and on the east side, No.3 plant is under construction. No.3 plant is a PWR type plant of 890 MWe output, and the start of commercial operation is scheduled in March, 1995. In the construction of No.3 plant, the concrete used for civil engineering and building works is about 430,000 m 3 , and for the improvement of the quality control of concrete, the pursuit of economic efficiency, the fostering of concrete technology of employee and the coprosperity with local industries, the facilities for manufacturing concrete were constructed within the premise of the power station. The amount of use of concrete and respective materials classified by respective fiscal years, and the amount of manufacture of concrete that determines the scale of the concrete plant are shown. As to the construction of the concrete plant, the foundation work was started in March, 1987, and the machine foundation and building works were started in May, 1987. The acceptance was completed on August 17, 1987. The facilities of manufacturing concrete, the manufacture of concrete, and the quality control of materials and concrete are reported. (author)

  1. 78 FR 12104 - Manufacturer of Controlled Substances; Notice of Registration; INB Hauser Pharmaceutical Services...

    Science.gov (United States)

    2013-02-21

    ...; Notice of Registration; INB Hauser Pharmaceutical Services, Inc. By Notice dated November 1, 2012, and published in the Federal Register on November 9, 2012, 77 FR 67398, InB Hauser Pharmaceutical Services, Inc... Hauser Pharmaceutical Services, Inc., to manufacture the listed basic class of controlled substance is...

  2. Start-up conditions and the performance of women - and men - controlled businesses in manufacturing industries

    Directory of Open Access Journals (Sweden)

    Otilia Driga

    2010-01-01

    Full Text Available Recent research into the economic performance of women-controlled firms suggests that their underperformance may not be the result of differences in the managerial ability of women as compared to men, and that it may in fact be a consequence of differing levels of start-up resources. Using accounting data, we examine the effects that selected start-up conditions have had on the observed economic performance of a sample of 4450 Spanish manufacturing firms. The results, which indicate significant differences in the initial conditions and show lower levels of assets and employee numbers in women-controlled firms, have implications for the economic performance of such firms.

  3. Role of Ontologies for CPS Implementation in Manufacturing

    Directory of Open Access Journals (Sweden)

    Garetti Marco

    2015-12-01

    Full Text Available Cyber Physical Systems are an evolution of embedded systems featuring a tight combination of collaborating computational elements that control physical entities. CPSs promise a great potential of innovation in many areas including manufacturing and production. This is because we obtain a very powerful, flexible, modular infrastructure allowing easy (re configurability and fast ramp-up of manufacturing applications by building a manufacturing system with modular mechatronic components (for machining, transportation and storage and embedded intelligence, by integrating them into a system, through a network connection. However, when building such kind of architectures, the way to supply the needed domain knowledge to real manufacturing applications arises as a problem to solve. In fact, a CPS based architecture for manufacturing is made of smart but independent manufacturing components without any knowledge of the role they have to play together in the real world of manufacturing applications. Ontologies can supply such kind of knowledge, playing a very important role in CPS for manufacturing. The paper deals with this intriguing theme, also presenting an implementation of this approach in a research project for the open automation of manufacturing systems, in which the power of CPS is complemented by the support of an ontology of the manufacturing domain.

  4. 78 FR 30332 - Manufacturer of Controlled Substances, Notice of Application, Austin Pharma, Llc.

    Science.gov (United States)

    2013-05-22

    ... DEPARTMENT OF JUSTICE Drug Enforcement Administration Manufacturer of Controlled Substances, Notice of Application, Austin Pharma, Llc. Pursuant to Sec. 1301.33(a), Title 21 of the Code of Federal Regulations (CFR), this is notice that on March 28, 2013, Austin Pharma, LLC., 811 Paloma Drive, Suite C...

  5. 77 FR 30027 - Manufacturer of Controlled Substances; Notice of Application; Austin Pharma, LLC.

    Science.gov (United States)

    2012-05-21

    ... DEPARTMENT OF JUSTICE Drug Enforcement Administration Manufacturer of Controlled Substances; Notice of Application; Austin Pharma, LLC. Pursuant to Sec. 1301.33(a), Title 21 of the Code of Federal Regulations (CFR), this is notice that on April 11, 2012, Austin Pharma, LLC., 811 Paloma Drive, Suite C...

  6. 78 FR 46613 - Manufacturer of Controlled Substances; Notice of Application; Siegfried (USA), LLC

    Science.gov (United States)

    2013-08-01

    ... DEPARTMENT OF JUSTICE Drug Enforcement Administration Manufacturer of Controlled Substances; Notice of Application; Siegfried (USA), LLC Pursuant to Sec. 1301.33(a), Title 21 of the Code of Federal Regulations (CFR), this is notice that on June 10, 2013, Siegfried (USA), LLC., 33 Industrial Park Road...

  7. 77 FR 70825 - Manufacturer of Controlled Substances; Notice of Application; Siegfried (USA), LLC

    Science.gov (United States)

    2012-11-27

    ... DEPARTMENT OF JUSTICE Drug Enforcement Administration Manufacturer of Controlled Substances; Notice of Application; Siegfried (USA), LLC Pursuant to Sec. 1301.33(a), Title 21 of the Code of Federal Regulations (CFR), this is notice that on November 5, 2012, Siegfried (USA) LLC, 33 Industrial Park Road...

  8. 78 FR 32458 - Manufacturer of Controlled Substances; Notice of Application; Siegfried USA, LLC

    Science.gov (United States)

    2013-05-30

    ... DEPARTMENT OF JUSTICE Drug Enforcement Administration Manufacturer of Controlled Substances; Notice of Application; Siegfried USA, LLC Pursuant to Sec. 1301.33(a), Title 21 of the Code of Federal Regulations (CFR), this is notice that on April 18, 2013, Siegfried USA, LLC., 33 Industrial Park Road...

  9. Hierarchical tailoring of strut architecture to control permeability of additive manufactured titanium implants.

    Science.gov (United States)

    Zhang, Z; Jones, D; Yue, S; Lee, P D; Jones, J R; Sutcliffe, C J; Jones, E

    2013-10-01

    Porous titanium implants are a common choice for bone augmentation. Implants for spinal fusion and repair of non-union fractures must encourage blood flow after implantation so that there is sufficient cell migration, nutrient and growth factor transport to stimulate bone ingrowth. Additive manufacturing techniques allow a large number of pore network designs. This study investigates how the design factors offered by selective laser melting technique can be used to alter the implant architecture on multiple length scales to control and even tailor the flow. Permeability is a convenient parameter that characterises flow, correlating to structure openness (interconnectivity and pore window size), tortuosity and hence flow shear rates. Using experimentally validated computational simulations, we demonstrate how additive manufacturing can be used to tailor implant properties by controlling surface roughness at a microstructual level (microns), and by altering the strut ordering and density at a mesoscopic level (millimetre). Copyright © 2013 The Authors. Published by Elsevier B.V. All rights reserved.

  10. Research on Mechanisms and Controlling Methods of Macro Defects in TC4 Alloy Fabricated by Wire Additive Manufacturing.

    Science.gov (United States)

    Ji, Lei; Lu, Jiping; Tang, Shuiyuan; Wu, Qianru; Wang, Jiachen; Ma, Shuyuan; Fan, Hongli; Liu, Changmeng

    2018-06-28

    Wire feeding additive manufacturing (WFAM) has broad application prospects because of its advantages of low cost and high efficiency. However, with the mode of lateral wire feeding, including wire and laser additive manufacturing, gas tungsten arc additive manufacturing etc., it is easy to generate macro defects on the surface of the components because of the anisotropy of melted wire, which limits the promotion and application of WFAM. In this work, gas tungsten arc additive manufacturing with lateral wire feeding is proposed to investigate the mechanisms of macro defects. The results illustrate that the defect forms mainly include side spatters, collapse, poor flatness, and unmelted wire. It was found that the heat input, layer thickness, tool path, and wire curvature can have an impact on the macro defects. Side spatters are the most serious defects, mainly because the droplets cannot be transferred to the center of the molten pool in the lateral wire feeding mode. This research indicates that the macro defects can be controlled by optimizing the process parameters. Finally, block parts without macro defects were fabricated, which is meaningful for the further application of WFAM.

  11. 77 FR 14022 - Guidance for Industry on Chemistry, Manufacturing, and Controls Information-Fermentation-Derived...

    Science.gov (United States)

    2012-03-08

    ...] Guidance for Industry on Chemistry, Manufacturing, and Controls Information--Fermentation-Derived... (CMC) Information-- Fermentation-Derived Intermediates, Drug Substances, and Related Drug Products for... to submit to support the CMC information for fermentation-derived intermediates, drug substances, and...

  12. Energy Efficiency in Manufacturing Systems

    CERN Document Server

    Thiede, Sebastian

    2012-01-01

    Energy consumption is of great interest to manufacturing companies. Beyond considering individual processes and machines, the perspective on process chains and factories as a whole holds major potentials for energy efficiency improvements. To exploit these potentials, dynamic interactions of different processes as well as auxiliary equipment (e.g. compressed air generation) need to be taken into account. In addition, planning and controlling manufacturing systems require  balancing technical, economic and environmental objectives. Therefore, an innovative and comprehensive methodology – with a generic energy flow-oriented manufacturing simulation environment as a core element – is developed and embedded into a step-by-step application cycle. The concept is applied in its entirety to a wide range of case studies such as aluminium die casting, weaving mills, and printed circuit board assembly in order to demonstrate the broad applicability and the benefits that can be achieved.

  13. [Chinese medicine industry 4.0:advancing digital pharmaceutical manufacture toward intelligent pharmaceutical manufacture].

    Science.gov (United States)

    Cheng, Yi-Yu; Qu, Hai-Bin; Zhang, Bo-Li

    2016-01-01

    A perspective analysis on the technological innovation in pharmaceutical engineering of Chinese medicine unveils a vision on "Future Factory" of Chinese medicine industry in mind. The strategy as well as the technical roadmap of "Chinese medicine industry 4.0" is proposed, with the projection of related core technology system. It is clarified that the technical development path of Chinese medicine industry from digital manufacture to intelligent manufacture. On the basis of precisely defining technical terms such as process control, on-line detection and process quality monitoring for Chinese medicine manufacture, the technical concepts and characteristics of intelligent pharmaceutical manufacture as well as digital pharmaceutical manufacture are elaborated. Promoting wide applications of digital manufacturing technology of Chinese medicine is strongly recommended. Through completely informationized manufacturing processes and multi-discipline cluster innovation, intelligent manufacturing technology of Chinese medicine should be developed, which would provide a new driving force for Chinese medicine industry in technology upgrade, product quality enhancement and efficiency improvement. Copyright© by the Chinese Pharmaceutical Association.

  14. Continuous improvement in manufacturing and inspection of fuel

    International Nuclear Information System (INIS)

    Domingon, A.; Ruiz, R.

    2015-01-01

    The manufacturing and inspection process of fuel assemblies in ENUSA is characterized by its robustness acquired over the last thirty years of experience in manufacturing. The reliability of these processes is based on a qualified processes and continuous improvement in the design and upgrading of equipment and optimization of software and manufacturing processes. Additionally, management and quality control systems have been improved in both software and measuring business objectives. this article emphasizes the improvements made over the past five years in management, production and inspection of fuel assemblies. (Author)

  15. Job rotation designed to prevent musculoskeletal disorders and control risk in manufacturing industries: A systematic review.

    Science.gov (United States)

    Padula, Rosimeire Simprini; Comper, Maria Luiza Caires; Sparer, Emily H; Dennerlein, Jack T

    2017-01-01

    To better understand job rotation in the manufacturing industry, we completed a systematic review asking the following questions: 1) How do job-rotation programs impact work-related musculoskeletal disorders (MSDs) and related risk control for these MSDs, as well as psychosocial factors? and 2) How best should the job rotation programs be designed? We searched MEDLINE, EMBASE, Business Source Premier, ISI Web of Knowledge, CINAHL, PsyINFO, Scopus, and SciELO databases for articles published in peer-reviewed journals. Eligible studies were examined by two independent reviewers for relevance (population of manufacturing workers, outcomes of musculoskeletal disorders, physical factors, psychosocial factors, and strategies used in job-rotation implantation) and methodological quality rating. From 10,809 potential articles, 71 were read for full text analysis. Of the 14 studies included for data extraction, two were non-randomized control trial studies, one was a case-control study, and 11 were cross-sectional comparisons. Only one, with a case-control design, was scored with good methodological quality. Currently, weak evidence exists supporting job rotation as a strategy for the prevention and control of musculoskeletal disorders. Job rotation did not appear to reduce the exposure of physical risk factors; yet, there are positive correlations between job rotation and higher job satisfaction. Worker training has been described as a crucial component of a successful job-rotation program. The studies reported a range of parameters used to implement and measure job-rotation programs. More rigorous studies are needed to better understand the full impact of job rotation on production and health. CRD42014013319. Copyright © 2016 Elsevier Ltd. All rights reserved.

  16. Statistical tools and control of internal lubricant content of inhalation grade HPMC capsules during manufacture.

    Science.gov (United States)

    Ayala, Guillermo; Díez, Fernando; Gassó, María T; Jones, Brian E; Martín-Portugués, Rafael; Ramiro-Aparicio, Juan

    2016-04-30

    The internal lubricant content (ILC) of inhalation grade HPMC capsules is a key factor to ensure good powder release when the patient inhales a medicine from a dry powder inhaler (DPI). Powder release from capsules has been shown to be influenced by the ILC. The characteristics used to measure this are the emitted dose, fine particle fraction and mass median aerodynamic diameter. In addition the ILC level is critical for capsule shell manufacture because it is an essential part of the process that cannot work without it. An experiment has been applied to the manufacture of inhalation capsules with the required ILC. A full factorial model was used to identify the controlling factors and from this a linear model has been proposed to improve control of the process. Copyright © 2016 Elsevier B.V. All rights reserved.

  17. Power electronic modules design and manufacture

    CERN Document Server

    Sheng, William W

    2004-01-01

    IntroductionSelection ProcedureMaterialsInsulating Substrate and MetallizationBase PlateBonding MaterialPower Interconnection and TerminalEncapsulantPlastic Case and Cover Manufacturing of Power IGBT ModulesManufacturing Process Process Control/Long-Term ReliabilityManufacturing FacilitiesManufacturing Flow Charts DesignThermal ManagementCircuit PartitioningDesign Guidelines and ConsiderationsThermal Results of Different Samples

  18. 77 FR 43863 - Manufacturer of Controlled Substances; Notice of Application; Boehringer Ingelheim Chemicals Inc.

    Science.gov (United States)

    2012-07-26

    ... DEPARTMENT OF JUSTICE Drug Enforcement Administration Manufacturer of Controlled Substances; Notice of Application; Boehringer Ingelheim Chemicals Inc. Pursuant to Sec. 1301.33(a), Title 21 of the Code of Federal Regulations (CFR), this is notice that on June 8, 2012, Boehringer Ingelheim Chemicals...

  19. 78 FR 39340 - Manufacturer of Controlled Substances; Notice of Application; Boehringer Ingelheim Chemicals, Inc.

    Science.gov (United States)

    2013-07-01

    ... DEPARTMENT OF JUSTICE Drug Enforcement Administration Manufacturer of Controlled Substances; Notice of Application; Boehringer Ingelheim Chemicals, Inc. Pursuant to Sec. 1301.33(a), Title 21 of the Code of Federal Regulations (CFR), this is notice that on May 31, 2013, Boehringer Ingelheim Chemicals...

  20. 77 FR 67398 - Manufacturer of Controlled Substances; Notice of Application; INB Hauser Pharmaceutical Services...

    Science.gov (United States)

    2012-11-09

    ... DEPARTMENT OF JUSTICE Drug Enforcement Administration Manufacturer of Controlled Substances; Notice of Application; INB Hauser Pharmaceutical Services, Inc. Pursuant to Sec. 1301.33(a), Title 21 of... Pharmaceutical Services, Inc., 6880 N. Broadway, Suite H, Denver, Colorado 80221, made application by letter to...

  1. Advanced Manufacturing for Thermal and Environmental Control Systems: Achieving National Energy Goals

    Energy Technology Data Exchange (ETDEWEB)

    Bogucz, Edward A. [Syracuse Univ., NY (United States)

    2017-02-20

    This project was part of a regional initiative in the five counties of Central New York (CNY) that received funding from the U.S. Department of Energy (DOE) and four other federal agencies through the 2012 Advanced Manufacturing Jobs and Innovation Accelerator Challenge (AMJIAC). The CNY initiative was focused on cultivating the emergent regional cluster in “Advanced Manufacturing for Thermal and Environmental Control (AM-TEC).” As one component of the CNY AM-TEC initiative, the DOE-funded project supported five research & development seed projects that strategically targeted: 1) needs and opportunities of CNY AM-TEC companies, and 2) the goal of DOE’s Advanced Manufacturing Office (AMO) to reduce energy consumption by 50% across product life-cycles over 10 years. The project also sought to fulfill the AMO mission of developing and demonstrating new, energy-efficient processing and materials technologies at a scale adequate to prove their value to manufacturers and spur investment. The five seed projects demonstrated technologies and processes that can reduce energy intensity and improve production as well as use less energy throughout their lifecycles. The project was conducted over three years in two 18-month budget periods. During the first budget period, two projects proposed in the original AMJAIC application were successfully completed: Seed Project 1 focused on saving energy in heat transfer processes via development of nano structured surfaces to significantly increase heat flux; Seed Project 2 addressed saving energy in data centers via subzero cooling of the computing processors. Also during the first budget period, a process was developed and executed to select a second round of seed projects via a competitive request for proposals from regional companies and university collaborators. Applicants were encouraged to form industry-academic partnerships to leverage experience and resources of public and private sectors in the CNY region. Proposals were

  2. Manufacturing strategy issues in selected Indian manufacturing industry

    Directory of Open Access Journals (Sweden)

    Mahender Singh

    2013-03-01

    Full Text Available This paper presents some findings of Indian manufacturing sectors viz. automobile (especially two-wheeler, tractor and general manufacturing industry. Various manufacturing strategy issues such as competitive priorities, improvement activities, and performance measures, have been identified and assessed in Indian context. Sector wise comparison of competitive priorities, improvement activities i.e. advanced manufacturing technology (AMT, integrated information systems (IIS, and advanced management systems (AMS, and performance measure, is provided. Our results showed that most of the Indian companies are still emphasizing on quality. However, automobile sector has set to compete globally with high innovation rate, faster new product development, and continuous improvement. It is also observed that Indian companies are investing more in AMS as compared to IIS and AMT. Manufacturing competence index is also computed for each sector.

  3. Hierarchical tailoring of strut architecture to control permeability of additive manufactured titanium implants

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Z. [Department of Materials, Imperial College London, South Kensington Campus, London, SW7 2AZ (United Kingdom); Jones, D. [School of Engineering, University of Liverpool, Brownlow Hill, Liverpool, L69 3GH (United Kingdom); Yue, S. [Manchester X-ray Imaging Facility, School of Materials, The University of Manchester, Oxford Road, M13 9PL (United Kingdom); Lee, P.D., E-mail: peter.lee@manchester.ac.uk [Manchester X-ray Imaging Facility, School of Materials, The University of Manchester, Oxford Road, M13 9PL (United Kingdom); Jones, J.R. [Department of Materials, Imperial College London, South Kensington Campus, London, SW7 2AZ (United Kingdom); Sutcliffe, C.J. [School of Engineering, University of Liverpool, Brownlow Hill, Liverpool, L69 3GH (United Kingdom); Jones, E. [Department of Advanced Technology, Stryker Orthopaedics, Raheen Business Park, Limerick (Ireland)

    2013-10-15

    Porous titanium implants are a common choice for bone augmentation. Implants for spinal fusion and repair of non-union fractures must encourage blood flow after implantation so that there is sufficient cell migration, nutrient and growth factor transport to stimulate bone ingrowth. Additive manufacturing techniques allow a large number of pore network designs. This study investigates how the design factors offered by selective laser melting technique can be used to alter the implant architecture on multiple length scales to control and even tailor the flow. Permeability is a convenient parameter that characterises flow, correlating to structure openness (interconnectivity and pore window size), tortuosity and hence flow shear rates. Using experimentally validated computational simulations, we demonstrate how additive manufacturing can be used to tailor implant properties by controlling surface roughness at a microstructual level (microns), and by altering the strut ordering and density at a mesoscopic level (millimetre). Highlights: • Experimentally validated permeability prediction tools for hierarchical implants. • Randomised structures form preferential flow channels with stronger shear flows. • Hierarchical strut structures allow independent tailoring of flow and pore size.

  4. Hierarchical tailoring of strut architecture to control permeability of additive manufactured titanium implants

    International Nuclear Information System (INIS)

    Zhang, Z.; Jones, D.; Yue, S.; Lee, P.D.; Jones, J.R.; Sutcliffe, C.J.; Jones, E.

    2013-01-01

    Porous titanium implants are a common choice for bone augmentation. Implants for spinal fusion and repair of non-union fractures must encourage blood flow after implantation so that there is sufficient cell migration, nutrient and growth factor transport to stimulate bone ingrowth. Additive manufacturing techniques allow a large number of pore network designs. This study investigates how the design factors offered by selective laser melting technique can be used to alter the implant architecture on multiple length scales to control and even tailor the flow. Permeability is a convenient parameter that characterises flow, correlating to structure openness (interconnectivity and pore window size), tortuosity and hence flow shear rates. Using experimentally validated computational simulations, we demonstrate how additive manufacturing can be used to tailor implant properties by controlling surface roughness at a microstructual level (microns), and by altering the strut ordering and density at a mesoscopic level (millimetre). Highlights: • Experimentally validated permeability prediction tools for hierarchical implants. • Randomised structures form preferential flow channels with stronger shear flows. • Hierarchical strut structures allow independent tailoring of flow and pore size

  5. Implementation of hierarchical design for manufacture rules in manufacturing processes

    OpenAIRE

    Parvez, Masud

    2008-01-01

    In order to shorten the product development cycle time, minimise overall cost and smooth transition into production, early consideration of manufacturing processes is important. Design for Manufacture (DFM) is the practice of designing products with manufacturing issues using an intelligent system, which translates 3D solid models into manufacturable features. Many existing and potential applications, particularly in the field of manufacturing, require various aspects of features technology. ...

  6. Guidelines on preparation of documentation required in PET radiopharmaceutical manufacturing

    International Nuclear Information System (INIS)

    2001-01-01

    This article made by the Nuclear Pharmacy Working Group, subcommittee on Medical Application of Cyclotron-Produced Radionuclides, Medical Science and Pharmaceutical Committee, Japan Radioisotope Association, described the actual examples of Standards, Standard Operating Procedure, Documents and so on for the purpose of operation along the Standards of Compounds Labeled with Positron Nuclides Approved as Established Techniques for Medical Use (2001 Revision). Examples were the organization for manufacturing and management, standard format of the product (for [ 18 F]2-deoxy-2-fluoro-D-glucose), standard for process control of manufacture, standard for control of manufacturing and hygiene, standard for quality, and standard operating procedures for entering and leaving the manufacturing facility, for the clean-bench and for the test of floating micro-particles. The second item involved the definition of the cyclotron target ( 18 O), generation of 18 F by the reaction (p, n), purification of the product, and prescription: the third item; storage of the product and manufacturing process control: and the fourth; education and training of personnel, and health management. (K.H.)

  7. Regulating Cannabis Manufacturing: Applying Public Health Best Practices from Tobacco Control.

    Science.gov (United States)

    Orenstein, Daniel G; Glantz, Stanton A

    2018-01-01

    State legalization and regulation of cannabis, despite continued federal illegality, is a massive shift in regulatory approach. Manufactured cannabis, including concentrates, extracts, edibles, tinctures, topicals and other products, has received less attention than more commonly used dried flower, but represents emerging regulatory challenges due to additives, potency, consumption methods, and abuse and misuse potential. In November 2017, the California Department of Public Health (CDPH) released initial cannabis manufacturing regulations as part of a new state regulatory structure. As the largest U.S. medical cannabis market (and largest legal adult use market in the world beginning in 2018), California's regulatory approach will potentially influence national and global policy. Comparing CDPH's initial regulations to tobacco control best practices reveals that, while the regulations recognize the need to protect public health, prioritizing public health over business interests requires stronger approaches to labeling, packaging, and product formulations. Based on tobacco best practices, we recommend that cannabis regulations incorporate large and proportionately sized informational labels, a prominent universal cannabis symbol, rotating and pictorial health warnings, mandatory plain packaging, a comprehensive ban on characterizing flavors and addictive additives, and strict limits on the potency of inhalable products and those easily confused with non-cannabis products.

  8. AN OVERVIEW OF PHARMACEUTICAL PROCESS VALIDATION AND PROCESS CONTROL VARIABLES OF TABLETS MANUFACTURING PROCESSES IN INDUSTRY

    OpenAIRE

    Mahesh B. Wazade*, Sheelpriya R. Walde and Abhay M. Ittadwar

    2012-01-01

    Validation is an integral part of quality assurance; the product quality is derived from careful attention to a number of factors including selection of quality parts and materials, adequate product and manufacturing process design, control of the process variables, in-process and end-product testing. Recently validation has become one of the pharmaceutical industry’s most recognized and discussed subjects. It is a critical success factor in product approval and ongoing commercialization, fac...

  9. A Process Management System for Networked Manufacturing

    Science.gov (United States)

    Liu, Tingting; Wang, Huifen; Liu, Linyan

    With the development of computer, communication and network, networked manufacturing has become one of the main manufacturing paradigms in the 21st century. Under the networked manufacturing environment, there exist a large number of cooperative tasks susceptible to alterations, conflicts caused by resources and problems of cost and quality. This increases the complexity of administration. Process management is a technology used to design, enact, control, and analyze networked manufacturing processes. It supports efficient execution, effective management, conflict resolution, cost containment and quality control. In this paper we propose an integrated process management system for networked manufacturing. Requirements of process management are analyzed and architecture of the system is presented. And a process model considering process cost and quality is developed. Finally a case study is provided to explain how the system runs efficiently.

  10. 77 FR 34073 - Manufacturer of Controlled Substances; Notice of Application; S&B Pharma, Inc.

    Science.gov (United States)

    2012-06-08

    ... DEPARTMENT OF JUSTICE Drug Enforcement Administration Manufacturer of Controlled Substances; Notice of Application; S&B Pharma, Inc. Pursuant to Sec. 1301.33(a), Title 21 of the Code of Federal Regulations (CFR), this is notice that on April 4, 2012, S&B Pharma Inc., 405 South Motor Avenue, Azusa...

  11. Quality control in manufacture of lead boron polyethylene plate

    International Nuclear Information System (INIS)

    Wu Ying

    2008-01-01

    For the quality assurance management in the manufacture of lead boron polyethylene plate,target shall be defined and planning shall be conducted first; personnel shall be trained to improve the execution force; institutional system shall be continuously upgraded and environment protection shall be strengthened.Quality management has achieved excellent result, with qualification rate for contracts reaches 100%, to ensure successful production. (author)

  12. DIMENSIONAL VERIFICATION AND QUALITY CONTROL OF IMPLANTS PRODUCED BY ADDITIVE MANUFACTURING

    Directory of Open Access Journals (Sweden)

    Teodor Toth

    2015-07-01

    Full Text Available Purpose: Development of computer technology and alternative manufacturing methods in form of additive manufacturing leads to the manufacture of products with complex shapes. In the field of medicine they include, inter alia, custom-made implants manufactured for a particular patient, such as cranial implants, maxillofacial implants, etc. With regard to the fact that such implants are inserted into a patient’s body, it is necessary to perform the verification, including the shape and dimensional verification. The article deals with the application of the industrial computer tomography within the process of inspection and verification of selected custom-made implant types.Methodology/Approach: The Department of Biomedical Engineering and Measurement performs the verification of medicinal products manufactured by the additive manufacturing technologies from the Ti-6Al-4V (Grade 5 titanium alloy, using the coordinate measuring machine Carl Zeiss Contura G2 and the industrial computed tomography machine Carl Zeiss Metrotom 1500. These equipment fulfil the requirements for the identification and evaluation of dimensions of both, the external and the internal structures. Findings: The article presents the possibilities of the computed tomography utilisation in the inspection of individual implant manufacture using the additive manufacturing technologies. The results indicate that with the adjustment of appropriate input parameters (alignment, this technology is appropriate for the analysis of shape deviations, when compared with the CAD model.Research Limitation/implication: With the increasing distance of measured object from X-ray source, the machine’s resolution function decreases. Decreasing of resolution has a minor impact on the measured dimensions (relatively high tolerances, but has a significant impact on the evaluation of porosity and inclusions. Originality/Value of paper: Currently, the verification of a manufactured implant  can be

  13. Tribology in Manufacturing Technology

    CERN Document Server

    2013-01-01

    The present book aims to provide research advances on tribology in manufacturing technology for modern industry. This book can be used as a research book for final undergraduate engineering course (for example, mechanical, manufacturing, materials, etc) or as a subject on manufacturing at the postgraduate level. Also, this book can serve as a useful reference for academics, manufacturing and tribology researchers, mechanical, mechanical, manufacturing and materials engineers, professionals in related industries with manufacturing and tribology.

  14. Good manufacturing practice - quality assurance programs

    International Nuclear Information System (INIS)

    Masefield, John; Thompson, Steven

    1986-01-01

    The concept of good manufacturing practice (GMP) in the medical device industry requires the use of controlled methods and equipment in performing each step in the device manufacturing process. Quality assurance programs are used to maintain compliance with GMP requirements by prescribing the operating and control procedures to be used. The specific elements of a quality assurance program for the radiation sterilization of medical devices are described. (author)

  15. Neural manufacturing: a novel concept for processing modeling, monitoring, and control

    Science.gov (United States)

    Fu, Chi Y.; Petrich, Loren; Law, Benjamin

    1995-09-01

    Semiconductor fabrication lines have become extremely costly, and achieving a good return from such a high capital investment requires efficient utilization of these expensive facilities. It is highly desirable to shorten processing development time, increase fabrication yield, enhance flexibility, improve quality, and minimize downtime. We propose that these ends can be achieved by applying recent advances in the areas of artificial neural networks, fuzzy logic, machine learning, and genetic algorithms. We use the term neural manufacturing to describe such applications. This paper describes our use of artificial neural networks to improve the monitoring and control of semiconductor process.

  16. Manufacture of disposal canisters

    International Nuclear Information System (INIS)

    Nolvi, L.

    2009-12-01

    The report summarizes the development work carried out in the manufacturing of disposal canister components, and present status, in readiness for manufacturing, of the components for use in assembly of spent nuclear fuel disposal canister. The disposal canister consist of two major components: the nodular graphite cast iron insert and overpack of oxygen-free copper. The manufacturing process for copper components begins with a cylindrical cast copper billet. Three different manufacturing processes i.e. pierce and draw, extrusion and forging are being developed, which produce a seamless copper tube or a tube with an integrated bottom. The pierce and draw process, Posiva's reference method, makes an integrated bottom possible and only the lid requires welding. Inserts for BWR-element are cast with 12 square channels and inserts for VVER 440-element with 12 round channels. Inserts for EPR-elements have four square channels. Casting of BWR insert type has been studied so far. Experience of casting inserts for PWR, which is similar to the EPR-type, has been got in co-operation with SKB. The report describes the processes being developed for manufacture of disposal canister components and some results of the manufacturing experiments are presented. Quality assurance and quality control in manufacture of canister component is described. (orig.)

  17. Manufacturing best practices and performance

    DEFF Research Database (Denmark)

    Szász, Levente; Demeter, Krisztina; Boer, Harry

    2014-01-01

    whether a) home and host country characteristics moderate the association between manufacturing practices and performance, and, thus, whether b) there are manufacturing practices that are universally best. Manufacturing practices and performance are measured using data collected through the fifth round...... analysis is used to develop groups of companies based on home and host country development. Exploratory factor analysis is applied to create bundles of manufacturing practices and performance measures. Then, using moderated multiple regressions (MMR) with interaction factor, and separate multiple...... regression analyses for each group of companies, bundles of manufacturing practices are identified that lead to best-in-class performance improvements. A range of control variables is introduced to help interpret the results. The study shows that home and host country context does affect the association...

  18. 77 FR 5849 - Manufacturer of Controlled Substances; Notice of Registration

    Science.gov (United States)

    2012-02-06

    ... company plans to manufacture a radioactive product to diagnose Parkinson's disease, and to manufacture a... physical security systems, verification of the company's compliance with state and local laws, and a review.... DEA has considered the factors in 21 U.S.C. 823(a) and determined that the registration of GE...

  19. Advances in Additive Manufacturing

    Science.gov (United States)

    2016-07-14

    with a collection of information if it does not display a currently valid OMB control number. PLEASE DO NOT RETURN YOUR FORM TO THE ABOVE ADDRESS...Hamilton • Beth Bimber Air Force Research Laboratory, Metals Branch • Eddie Schwalbach • Mike Groeber • Benjamin Leever • James Hardin...conducting more in-field, or point-of-need, manufacturing than ever before. Other areas of concentration include man- machine interface, capabilities

  20. 21 CFR 1303.21 - Individual manufacturing quotas.

    Science.gov (United States)

    2010-04-01

    ... controlled substance listed in Schedule I or II, and who applies for a manufacturing quota, an individual... basic class. Any manufacturing quota fixed and issued by the Administrator shall be subject to his... 21 Food and Drugs 9 2010-04-01 2010-04-01 false Individual manufacturing quotas. 1303.21 Section...

  1. Towards an integration of process planning and production planning and control for flexible manufacturing systems

    NARCIS (Netherlands)

    Gaalman, GJC; Slomp, J; Suresh, NC

    This introduction article attempts to present some major issues relating to the integration of process planning and production planning and control (PPC) for flexible manufacturing systems (FMSs). It shows that the performance of an FMS can be significantly improved and FMS capabilities more

  2. Design, manufacture and installation of measuring and control equipments for the advanced thermal prototype reactor 'Fugen'

    International Nuclear Information System (INIS)

    Hirota, Shigeo; Kawabata, Yoshinori

    1979-01-01

    The advanced thermal prototype reactor ''Fugen'' attained the criticality on March 20, 1978, and 100% output operation on November 13, 1978. On March 20, 1979, it passed the final inspection, and since then, it has continued the smooth operation up to now. The measuring and control equipments are provided for grasping the operational conditions of the plant and operating it safely and efficiently. At the time of designing, manufacturing and installing the measuring and control equipments for Fugen, it was required to clarify the requirements of the plant design, to secure the sufficient functions, and to improve the operational process, maintainability and the reliability and accuracy of the equipments. Many design guidelines and criteria were decided in order to coordinate the conditions among five manufacturers and give the unified state as one plant. The outline of the instrumentations for neutrons, radiation monitoring and process data, the control systems for reactivity, reactor output, pressure and water supply, the safety protection system, and the process computer are described. Finally, the installations and tests of the measuring and control equipments are explained. The aseismatic capability of the equipments was confirmed. (Kako, I.)

  3. Controlling the extrudate swell in melt extrusion additive manufacturing of 3D scaffolds: a designed experiment.

    Science.gov (United States)

    Yousefi, Azizeh-Mitra; Smucker, Byran; Naber, Alex; Wyrick, Cara; Shaw, Charles; Bennett, Katelyn; Szekely, Sarah; Focke, Carlie; Wood, Katherine A

    2018-02-01

    Tissue engineering using three-dimensional porous scaffolds has shown promise for the restoration of normal function in injured and diseased tissues and organs. Rigorous control over scaffold architecture in melt extrusion additive manufacturing is highly restricted mainly due to pronounced variations in the deposited strand diameter upon any variations in process conditions and polymer viscoelasticity. We have designed an I-optimal, split-plot experiment to study the extrudate swell in melt extrusion additive manufacturing and to control the scaffold architecture. The designed experiment was used to generate data to relate three responses (swell, density, and modulus) to a set of controllable factors (plotting needle diameter, temperature, pressure, and the dispensing speed). The fitted regression relationships were used to optimize the three responses simultaneously. The swell response was constrained to be close to 1 while maximizing the modulus and minimizing the density. Constraining the extrudate swell to 1 generates design-driven scaffolds, with strand diameters equal to the plotting needle diameter, and allows a greater control over scaffold pore size. Hence, the modulus of the scaffolds can be fully controlled by adjusting the in-plane distance between the deposited strands. To the extent of the model's validity, we can eliminate the effect of extrudate swell in designing these scaffolds, while targeting a range of porosity and modulus appropriate for bone tissue engineering. The result of this optimization was a predicted modulus of 14 MPa and a predicted density of 0.29 g/cm 3 (porosity ≈ 75%) using polycaprolactone as scaffold material. These predicted responses corresponded to factor levels of 0.6 μm for the plotting needle diameter, plotting pressure of 2.5 bar, melt temperature of 113.5 °C, and dispensing speed of 2 mm/s. The validation scaffold enabled us to quantify the percentage difference for the predictions, which was 9.5% for the

  4. Eradication of Productivity Related Problems Through Lean Principles In Integrated Manufacturing Environment

    Directory of Open Access Journals (Sweden)

    Rahul

    2013-06-01

    Full Text Available In this competitive era, manufacturing enterprises struggle to adopt cost-effective manufacturing systems. Overview of the recent manufacturing enterprises shows that successful global manufacturing enterprises have distributed their manufacturing capabilities over the globe. The successes of distributed integrated manufacturing enterprises depend upon the adaptation of appropriate manufacturing technologies like computer integrated manufacturing (CIM under the global collaborative environment along with the principles of lean manufacturing so that their corporate goals are achieved. CIM is an umbrella term which involves automated design, analysis, planning manufacturing, dispatching, customer-interaction, purchasing, cost accounting, inventory control and factory floor functions, which are inter-linked through the computer, to control all the campus-wide manufacturing related operations. It helps to improve the performance of a firm by integrating various areas of manufacturing business in which most of lean ideas are embedded. These lean ideas cause work in a process to be performed with minimum of non-value adding activities and focus on customers’ needs by delivering them at minimum time, with high quality and at minimum cost by eliminating hidden waste. What happens at the shop floor of even an integrated industry is that proper and timely attention is not paid to the intangible lean principles in the manual part of the CIM system which results in substantial loss of the plant productivity. Therefore the objective of this research paper is to investigate the different poor productivity-related problems in a partially integrated manufacturing environment and lay down the remedial measures to eradicate them using ‘Juran’s problem solving techniques’ and various ‘lean tools’ which results in the reduced wastages and hence improved productivity.

  5. 40 CFR 763.165 - Manufacture and importation prohibitions.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Manufacture and importation...) TOXIC SUBSTANCES CONTROL ACT ASBESTOS Prohibition of the Manufacture, Importation, Processing, and Distribution in Commerce of Certain Asbestos-Containing Products; Labeling Requirements § 763.165 Manufacture...

  6. The current state of development works for manufacturing and methods of controlling the nuclear fuel for NPPs of Ukraine

    International Nuclear Information System (INIS)

    Odeychuk, N.P.; Levenets, V.V.; Krasnorutsky, V.S.

    2000-01-01

    The paper presents the results of NSC KIPT researches on manufacturing the fuel microspheres and pellets based on uranium dioxide. The data on fuel characteristics for different manufacturing stages are given. The problems of improving the fuel quality with changing the structure characteristics of pellets are considered. Demonstrated is the hardware for pellet controlling and presented are the new ways for developing the methods of controlling the nuclear fuel: X-ray fluorescent analysis; complex of nuclear-physical methods on the base of accelerators; laser-excitation energy-mass-spectrometer. (author)

  7. Microbiological criteria for good manufacturing practice (GMP)

    Energy Technology Data Exchange (ETDEWEB)

    Farkas, J [Inst. of Preservation and Livestock Products Technology, Univ. of Horticulture and Food Industry, Budapest (Hungary); Zukal, E [Inst. of Preservation and Livestock Products Technology, Univ. of Horticulture and Food Industry, Budapest (Hungary)

    1992-01-01

    Good manufacturing practice (GMP) consist of an effective manufacturing operation and an effective application of food control. GMP is best supported by the Hazard Analysis Critical Control Point system (HACCP) of the preventive quality assurance, which requires that food irradiation as any food processing technology should be used only with foods of an acceptable quality and adequate handling and storage procedures should precede and follow the processing. The paper concentrates on the first element of the HACCP system for an irradiation plant: the incoming product control, i.e. whether GMP of foods to be irradiated can be assessed by establishing microbiological criteria for their previous good manufacturing practice. In this regard, it summarizes considerations and findings of a ''Consultation on Microbiological Criteria for Foods to be Further Processed Including by Irradiation'' held in 1989 by the International Consultative Group on Food irradiation at the Headquarters of the World Health Organization, Geneva. Difficulties in establishing reference values and defining good manufacturing practices will be pointed out. (orig.)

  8. Microbiological criteria for good manufacturing practice (GMP)

    International Nuclear Information System (INIS)

    Farkas, J.; Zukal, E.

    1992-01-01

    Good manufacturing practice (GMP) consist of an effective manufacturing operation and an effective application of food control. GMP is best supported by the Hazard Analysis Critical Control Point system (HACCP) of the preventive quality assurance, which requires that food irradiation as any food processing technology should be used only with foods of an acceptable quality and adequate handling and storage procedures should precede and follow the processing. The paper concentrates on the first element of the HACCP system for an irradiation plant: the incoming product control, i.e. whether GMP of foods to be irradiated can be assessed by establishing microbiological criteria for their previous good manufacturing practice. In this regard, it summarizes considerations and findings of a ''Consultation on Microbiological Criteria for Foods to be Further Processed Including by Irradiation'' held in 1989 by the International Consultative Group on Food irradiation at the Headquarters of the World Health Organization, Geneva. Difficulties in establishing reference values and defining good manufacturing practices will be pointed out. (orig.) [de

  9. Implementation of an advanced hybrid MPC-PID control system using PAT tools into a direct compaction continuous pharmaceutical tablet manufacturing pilot plant.

    Science.gov (United States)

    Singh, Ravendra; Sahay, Abhishek; Karry, Krizia M; Muzzio, Fernando; Ierapetritou, Marianthi; Ramachandran, Rohit

    2014-10-01

    It is desirable for a pharmaceutical final dosage form to be manufactured through a quality by design (QbD)-based approach rather than a quality by testing (QbT) approach. An automatic feedback control system coupled with PAT tools that is part of the QbD paradigm shift, has the potential to ensure that the pre-defined end product quality attributes are met in a time and cost efficient manner. In this work, an advanced hybrid MPC-PID control architecture coupled with real time inline/online monitoring tools and principal components analysis (PCA) based additional supervisory control layer has been proposed for a continuous direct compaction tablet manufacturing process. The advantages of both MPC and PID have been utilized in a hybrid scheme. The control hardware and software integration and implementation of the control system has been demonstrated using feeders and blending unit operation of a continuous tablet manufacturing pilot plant and an NIR based PAT tool. The advanced hybrid MPC-PID control scheme leads to enhanced control loop performance of the critical quality attributes in comparison to a regulatory (e.g. PID) control scheme indicating its potential to improve pharmaceutical product quality. Copyright © 2014 Elsevier B.V. All rights reserved.

  10. Safety concerns in composite manufacturing and machining

    Science.gov (United States)

    Asmatulu, Eylem; Alonayni, Abdullah; Alamir, Mohammed

    2018-03-01

    Because of the superior properties, composites have been used in many industrial applications, including aerospace, wind turbines, ships, cars, fishing rods, storage tanks, swimming pool panels, and baseball bats. Each application may require different combinations of reinforcements and matrices, which make the manufacturing safety even more challenging while working on these substances. In this study, safety issues in composite manufacturing and machining were investigated in detail, and latest developments were provided for workers. The materials most frequently used in composite manufacturing, such as matrix (polyester, vinylester, phenolic, epoxies, methyl ethyl ketone peroxide, benzoil peroxide, hardeners, and solvents), and reinforcement materials (carbon, glass and Kevlar fibers, honeycomb and foams) can be highly toxic to human body. These materials can also be very toxic to the environment when dumped out uncontrollably, creating major future health and environmental concerns. Throughout the manufacturing process, workers inhale vapors of the liquid matrix, hardeners and solvents / thinners, as well as reinforcement materials (chopped fibers and particles) in airborne. Milling, cutting and machining of the composites can further increase the toxic inhalations of airborne composite particles, resulting in major rashes, irritation, skin disorders, coughing, severe eye and lung injury and other serious illnesses. The major portions of these hazardous materials can be controlled using appropriate personal protective equipment for the chemicals and materials used in composite manufacturing and machining. This study provides best possible safety practices utilized in composite manufacturing facilities for workers, engineers and other participants.

  11. Kodak Skills Enhancement Program Curriculum: Math for Manufacturing and Quality Control. Report No. AEP-93-01.

    Science.gov (United States)

    Beaudin, Bart P.; And Others

    This teacher's guide is intended for use in helping Kodak Corporation employees develop the basic mathematics skills required to perform the manufacturing and quality control tasks expected of them. The following topics are covered in the first five modules: the four basic functions (adding, subtracting, multiplying, and dividing), calculations…

  12. Antimicrobial Peptides in Biomedical Device Manufacturing

    Science.gov (United States)

    Riool, Martijn; de Breij, Anna; Drijfhout, Jan W.; Nibbering, Peter H.; Zaat, Sebastian A. J.

    2017-08-01

    Over the past decades the use of medical devices, such as catheters, artificial heart valves, prosthetic joints and other implants, has grown significantly. Despite continuous improvements in device design, surgical procedures and wound care, biomaterial-associated infections (BAI) are still a major problem in modern medicine. Conventional antibiotic treatment often fails due to the low levels of antibiotic at the site of infection. The presence of biofilms on the biomaterial and/or the multidrug-resistant phenotype of the bacteria further impair the efficacy of antibiotic treatment. Removal of the biomaterial is then the last option to control the infection. Clearly, there is a pressing need for alternative strategies to prevent and treat BAI. Synthetic antimicrobial peptides (AMPs) are considered promising candidates as they are active against a broad spectrum of (antibiotic-resistant) planktonic bacteria and biofilms. Moreover, bacteria are less likely to develop resistance to these rapidly-acting peptides. In this review we highlight the four main strategies, three of which applying AMPs, in biomedical device manufacturing to prevent BAI. The first involves modification of the physicochemical characteristics of the surface of implants. Immobilization of AMPs on surfaces of medical devices with a variety of chemical techniques is essential in the second strategy. The main disadvantage of these two strategies relates to the limited antibacterial effect in the tissue surrounding the implant. This limitation is addressed by the third strategy that releases AMPs from a coating in a controlled fashion. Lastly, AMPs can be integrated in the design and manufacturing of additively manufactured / 3D-printed implants, owing to the physicochemical characteristics of the implant material and the versatile manufacturing technologies compatible with antimicrobials incorporation. These novel technologies utilizing AMPs will contribute to development of novel and safe

  13. Antimicrobial Peptides in Biomedical Device Manufacturing

    Directory of Open Access Journals (Sweden)

    Martijn Riool

    2017-08-01

    Full Text Available Over the past decades the use of medical devices, such as catheters, artificial heart valves, prosthetic joints, and other implants, has grown significantly. Despite continuous improvements in device design, surgical procedures, and wound care, biomaterial-associated infections (BAI are still a major problem in modern medicine. Conventional antibiotic treatment often fails due to the low levels of antibiotic at the site of infection. The presence of biofilms on the biomaterial and/or the multidrug-resistant phenotype of the bacteria further impair the efficacy of antibiotic treatment. Removal of the biomaterial is then the last option to control the infection. Clearly, there is a pressing need for alternative strategies to prevent and treat BAI. Synthetic antimicrobial peptides (AMPs are considered promising candidates as they are active against a broad spectrum of (antibiotic-resistant planktonic bacteria and biofilms. Moreover, bacteria are less likely to develop resistance to these rapidly-acting peptides. In this review we highlight the four main strategies, three of which applying AMPs, in biomedical device manufacturing to prevent BAI. The first involves modification of the physicochemical characteristics of the surface of implants. Immobilization of AMPs on surfaces of medical devices with a variety of chemical techniques is essential in the second strategy. The main disadvantage of these two strategies relates to the limited antibacterial effect in the tissue surrounding the implant. This limitation is addressed by the third strategy that releases AMPs from a coating in a controlled fashion. Lastly, AMPs can be integrated in the design and manufacturing of additively manufactured/3D-printed implants, owing to the physicochemical characteristics of the implant material and the versatile manufacturing technologies compatible with antimicrobials incorporation. These novel technologies utilizing AMPs will contribute to development of novel

  14. Population-based strategies to control manufacturing epidemics.

    Science.gov (United States)

    Gorini, Giuseppe

    2017-01-01

    "The multinational corporations producing tobacco, alcohol, soft drinks, and processed foods have a role of vectors in the increase of chronic diseases, so that one can speak of manufacturing epidemics. The main aim of this paper is to conduct a literature review on different approaches in population-based interventions to stem the rise in consumption of unhealthy products. Different approaches were found: • command-and-control regulations: the route is definitely more advanced for tobacco with the implementation of an international treaty, which requires 180 ratifying states to implement a series of tobacco control policies. Similar regulations have been partially adopted to reduce alcohol use and to increase taxes of sugar-sweetened beverages; • multinational corporations in few Countries can voluntarily adopt recommendations on media campaigns and on labelling of soft drinks and processed foods; • in order to reduce salt in foods, many Countries developed voluntary agreements with industries with monitoring systems to assess compliance. Population-based interventions to try to align the interests of multinational corporations with those of public health are described in literature: • the "Health Footprint" programme; • the performance-based regulation which could oblige industry to take responsibility to reduce the harmful consequences of the use of their unhealthy commodities; • the price-cap regulation, usually applied to the utilities sector, would set a cap on the price of the tobacco industry, raising the tobacco taxes by 500 million euros per year. In order to reduce the burden of chronic disease, one of the objectives of the Italian National Prevention Plan, a working group including non-governmental organizations and experts in communication, social marketing, and lifestyles should be organized by the Ministry of Health in order to identify which population-based interventions could be implemented in Italy in next years to stem the rise of

  15. Manufacturing Cell Therapies Using Engineered Biomaterials.

    Science.gov (United States)

    Abdeen, Amr A; Saha, Krishanu

    2017-10-01

    Emerging manufacturing processes to generate regenerative advanced therapies can involve extensive genomic and/or epigenomic manipulation of autologous or allogeneic cells. These cell engineering processes need to be carefully controlled and standardized to maximize safety and efficacy in clinical trials. Engineered biomaterials with smart and tunable properties offer an intriguing tool to provide or deliver cues to retain stemness, direct differentiation, promote reprogramming, manipulate the genome, or select functional phenotypes. This review discusses the use of engineered biomaterials to control human cell manufacturing. Future work exploiting engineered biomaterials has the potential to generate manufacturing processes that produce standardized cells with well-defined critical quality attributes appropriate for clinical testing. Copyright © 2017 Elsevier Ltd. All rights reserved.

  16. Control of three different continuous pharmaceutical manufacturing processes: Use of soft sensors.

    Science.gov (United States)

    Rehrl, Jakob; Karttunen, Anssi-Pekka; Nicolaï, Niels; Hörmann, Theresa; Horn, Martin; Korhonen, Ossi; Nopens, Ingmar; De Beer, Thomas; Khinast, Johannes G

    2018-05-30

    One major advantage of continuous pharmaceutical manufacturing over traditional batch manufacturing is the possibility of enhanced in-process control, reducing out-of-specification and waste material by appropriate discharge strategies. The decision on material discharge can be based on the measurement of active pharmaceutical ingredient (API) concentration at specific locations in the production line via process analytic technology (PAT), e.g. near-infrared (NIR) spectrometers. The implementation of the PAT instruments is associated with monetary investment and the long term operation requires techniques avoiding sensor drifts. Therefore, our paper proposes a soft sensor approach for predicting the API concentration from the feeder data. In addition, this information can be used to detect sensor drift, or serve as a replacement/supplement of specific PAT equipment. The paper presents the experimental determination of the residence time distribution of selected unit operations in three different continuous processing lines (hot melt extrusion, direct compaction, wet granulation). The mathematical models describing the soft sensor are developed and parameterized. Finally, the suggested soft sensor approach is validated on the three mentioned, different continuous processing lines, demonstrating its versatility. Copyright © 2018 Elsevier B.V. All rights reserved.

  17. Consistent manufacturing and quality control of a highly complex recombinant polyclonal antibody product for human therapeutic use.

    Science.gov (United States)

    Frandsen, Torben P; Naested, Henrik; Rasmussen, Søren K; Hauptig, Peter; Wiberg, Finn C; Rasmussen, Lone Kjaer; Jensen, Anne Marie Valentin; Persson, Pia; Wikén, Margareta; Engström, Anders; Jiang, Yun; Thorpe, Susan J; Förberg, Cecilia; Tolstrup, Anne B

    2011-09-01

    The beneficial effect of antibody therapy in human disease has become well established mainly for the treatment of cancer and immunological disorders. The inherent monospecificity of mAbs present limitations to mAb therapy which have become apparent notably in addressing complex entities like infectious agents or heterogenic endogenous targets. For such indications mixtures of antibodies comprising a combination of specificities would convey more potent biological effect which could translate into therapeutic efficacy. Recombinant polyclonal antibodies (rpAb) consisting of a defined number of well-characterized mAbs constitute a new class of target specific antibody therapy. We have developed a cost-efficient cell banking and single-batch manufacturing concept for the production of such products and demonstrate that a complex pAb composition, rozrolimupab, comprising 25 individual antibodies can be manufactured in a highly consistent manner in a scaled-up manufacturing process. We present a strategy for the release and characterization of antibody mixtures which constitute a complete series of chemistry, manufacturing, and control (CMC) analytical methods to address identity, purity, quantity, potency, and general characteristics. Finally we document selected quality attributes of rozrolimupab based on a battery of assays at the genetic-, protein-, and functional level and demonstrate that the manufactured rozrolimupab batches are highly pure and very uniform in their composition. Copyright © 2011 Wiley Periodicals, Inc.

  18. Design and manufacture NCS instruments for cement factories

    International Nuclear Information System (INIS)

    Nguyen Thanh Tuy; Nguyen Tien Dung; Dang Nguyet Anh; Nguyen Phuc; Khuong Thanh Tuan; Luong Duc Long; Pham Trong Quyen

    2003-01-01

    The ministry project 'Design and manufacture some of NCS instruments for cement factories' is a part of instrumentation for cement production in Vietnam. The objectives of the project include: 1/Design and manufacture the automatic control system for cement raw material mixing, connected to components X-ray analyzer through serial port of PC; 2/Design and manufacture the automatic discharge control system using gamma rays. The instruments, made by the project , for controlling the conveyor belt weighing machine can be easily improved for various types of conveyor belt weighing machines. Their mobility and software equipped can be adapted for requirement of modern cement production technology. The instruments are operating well in some cement factories and they are helping in quality control. (NHA)

  19. Competitive manufacturing strategies for the manufacturing industries in Turkey

    OpenAIRE

    Ulusoy, Gündüz; Ulusoy, Gunduz

    2003-01-01

    In this study, results of the research into competitive manufacturing strategies of companies in four different sector studies covering 82 companies from the electronics, cement, automotive manufacturers, and appliances part and component suppliers in Turkey are presented. The data used in the study are gathered by conducting four sector surveys in 1997 and 1998 using a questionnaire supported by some follow-up interviews and site visits. A competitive manufacturing strategy is represented he...

  20. 32 CFR 507.6 - Authority to manufacture.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 3 2010-07-01 2010-07-01 true Authority to manufacture. 507.6 Section 507.6... PUBLIC RELATIONS MANUFACTURE AND SALE OF DECORATIONS, MEDALS, BADGES, INSIGNIA, COMMERCIAL USE OF HERALDIC DESIGNS AND HERALDIC QUALITY CONTROL PROGRAM Manufacture and Sale of Decorations, Medals, Badges...

  1. Virtual Manufacturing Techniques Designed and Applied to Manufacturing Activities in the Manufacturing Integration and Technology Branch

    Science.gov (United States)

    Shearrow, Charles A.

    1999-01-01

    One of the identified goals of EM3 is to implement virtual manufacturing by the time the year 2000 has ended. To realize this goal of a true virtual manufacturing enterprise the initial development of a machinability database and the infrastructure must be completed. This will consist of the containment of the existing EM-NET problems and developing machine, tooling, and common materials databases. To integrate the virtual manufacturing enterprise with normal day to day operations the development of a parallel virtual manufacturing machinability database, virtual manufacturing database, virtual manufacturing paradigm, implementation/integration procedure, and testable verification models must be constructed. Common and virtual machinability databases will include the four distinct areas of machine tools, available tooling, common machine tool loads, and a materials database. The machine tools database will include the machine envelope, special machine attachments, tooling capacity, location within NASA-JSC or with a contractor, and availability/scheduling. The tooling database will include available standard tooling, custom in-house tooling, tool properties, and availability. The common materials database will include materials thickness ranges, strengths, types, and their availability. The virtual manufacturing databases will consist of virtual machines and virtual tooling directly related to the common and machinability databases. The items to be completed are the design and construction of the machinability databases, virtual manufacturing paradigm for NASA-JSC, implementation timeline, VNC model of one bridge mill and troubleshoot existing software and hardware problems with EN4NET. The final step of this virtual manufacturing project will be to integrate other production sites into the databases bringing JSC's EM3 into a position of becoming a clearing house for NASA's digital manufacturing needs creating a true virtual manufacturing enterprise.

  2. JIT Manufacturing: A Survey of Implementations in Small and Large U.S. Manufacturers

    OpenAIRE

    Richard E. White; John N. Pearson; Jeffrey R. Wilson

    1999-01-01

    Since the early 1980s, the diffusion of Just-In-Time (JIT) manufacturing from Japanese manufacturers to U.S. manufacturers has progressed at an accelerated rate. At this stage of the diffusion process, JIT implementations are more common and more advanced in large U.S. manufacturers than in small; consequently, U.S. businessmen's understanding of issues associated with JIT implementations in large manufacturers is more developed than that of small manufacturers. When small manufacturers repre...

  3. Method and apparatus for manufacturing gas tags

    International Nuclear Information System (INIS)

    Gross, K.C.; Laug, M.T.

    1996-01-01

    For use in the manufacture of gas tags employed in a gas tagging failure detection system for a nuclear reactor, a plurality of commercial feed gases each having a respective noble gas isotopic composition are blended under computer control to provide various tag gas mixtures having selected isotopic ratios which are optimized for specified defined conditions such as cost. Using a new approach employing a discrete variable structure rather than the known continuous-variable optimization problem, the computer controlled gas tag manufacturing process employs an analytical formalism from condensed matter physics known as stochastic relaxation, which is a special case of simulated annealing, for input feed gas selection. For a tag blending process involving M tag isotopes with N distinct feed gas mixtures commercially available from an enriched gas supplier, the manufacturing process calculates the cost difference between multiple combinations and specifies gas mixtures which approach the optimum defined conditions. The manufacturing process is then used to control tag blending apparatus incorporating tag gas canisters connected by stainless-steel tubing with computer controlled valves, with the canisters automatically filled with metered quantities of the required feed gases. 4 figs

  4. Raw materials in the manufacture of biotechnology products: regulatory considerations.

    Science.gov (United States)

    Cordoba-Rodriguez, Ruth

    2010-01-01

    The Food and Drug Administration's Pharmaceutical cGMPs for the 21st Century initiative emphasizes science and risk-based approaches in the manufacture of drugs. These approaches are reflected in the International Conference on Harmonization (ICH) guidances ICH Q8, Q9, and Q10 and encourage a comprehensive assessment of the manufacture of a biologic, including all aspects of manufacture that have the potential to affect the finished drug product. Appropriate assessment and management of raw materials are an important part of this initiative. Ideally, a raw materials program should strive to assess and minimize the risk to product quality. With this in mind, risk-assessment concepts and control strategies will be discussed and illustrated by examples, with an emphasis on the impact of raw materials on cell substrates. Finally, the life cycle of the raw material will be considered, including its potential to affect the drug product life cycle. In this framework, the supply chain and the vendor-manufacturer relationship will be explored as important parts of an adequate raw materials control strategy.

  5. Mechanics and energetics in tool manufacture and use: a synthetic approach.

    Science.gov (United States)

    Wang, Liyu; Brodbeck, Luzius; Iida, Fumiya

    2014-11-06

    Tool manufacture and use are observed not only in humans but also in other animals such as mammals, birds and insects. Manufactured tools are used for biomechanical functions such as effective control of fluids and small solid objects and extension of reaching. These tools are passive and used with gravity and the animal users' own energy. From the perspective of evolutionary biology, manufactured tools are extended phenotypes of the genes of the animal and exhibit phenotypic plasticity. This incurs energetic cost of manufacture as compared to the case with a fixed tool. This paper studies mechanics and energetics aspects of tool manufacture and use in non-human beings. Firstly, it investigates possible mechanical mechanisms of the use of passive manufactured tools. Secondly, it formulates the energetic cost of manufacture and analyses when phenotypic plasticity benefits an animal tool maker and user. We take a synthetic approach and use a controlled physical model, i.e. a robot arm. The robot is capable of additively manufacturing scoop and gripper structures from thermoplastic adhesives to pick and place fluid and solid objects, mimicking primates and birds manufacturing tools for a similar function. We evaluate the effectiveness of tool use in pick-and-place and explain the mechanism for gripper tools picking up solid objects with a solid-mechanics model. We propose a way to formulate the energetic cost of tool manufacture that includes modes of addition and reshaping, and use it to analyse the case of scoop tools. Experiment results show that with a single motor trajectory, the robot was able to effectively pick and place water, rice grains, a pebble and a plastic box with a scoop tool or gripper tools that were manufactured by itself. They also show that by changing the dimension of scoop tools, the energetic cost of tool manufacture and use could be reduced. The work should also be interesting for engineers to design adaptive machines. © 2014 The Author

  6. Mechanics and energetics in tool manufacture and use: a synthetic approach

    Science.gov (United States)

    Wang, Liyu; Brodbeck, Luzius; Iida, Fumiya

    2014-01-01

    Tool manufacture and use are observed not only in humans but also in other animals such as mammals, birds and insects. Manufactured tools are used for biomechanical functions such as effective control of fluids and small solid objects and extension of reaching. These tools are passive and used with gravity and the animal users' own energy. From the perspective of evolutionary biology, manufactured tools are extended phenotypes of the genes of the animal and exhibit phenotypic plasticity. This incurs energetic cost of manufacture as compared to the case with a fixed tool. This paper studies mechanics and energetics aspects of tool manufacture and use in non-human beings. Firstly, it investigates possible mechanical mechanisms of the use of passive manufactured tools. Secondly, it formulates the energetic cost of manufacture and analyses when phenotypic plasticity benefits an animal tool maker and user. We take a synthetic approach and use a controlled physical model, i.e. a robot arm. The robot is capable of additively manufacturing scoop and gripper structures from thermoplastic adhesives to pick and place fluid and solid objects, mimicking primates and birds manufacturing tools for a similar function. We evaluate the effectiveness of tool use in pick-and-place and explain the mechanism for gripper tools picking up solid objects with a solid-mechanics model. We propose a way to formulate the energetic cost of tool manufacture that includes modes of addition and reshaping, and use it to analyse the case of scoop tools. Experiment results show that with a single motor trajectory, the robot was able to effectively pick and place water, rice grains, a pebble and a plastic box with a scoop tool or gripper tools that were manufactured by itself. They also show that by changing the dimension of scoop tools, the energetic cost of tool manufacture and use could be reduced. The work should also be interesting for engineers to design adaptive machines. PMID:25209405

  7. Microbiological criteria for good manufacturing practice (GMP)

    Energy Technology Data Exchange (ETDEWEB)

    Farkas, J. (Inst. of Preservation and Livestock Products Technology, Univ. of Horticulture and Food Industry, Budapest (Hungary)); Zukal, E. (Inst. of Preservation and Livestock Products Technology, Univ. of Horticulture and Food Industry, Budapest (Hungary))

    1992-01-01

    Good manufacturing practice (GMP) consist of an effective manufacturing operation and an effective application of food control. GMP is best supported by the Hazard Analysis Critical Control Point system (HACCP) of the preventive quality assurance, which requires that food irradiation as any food processing technology should be used only with foods of an acceptable quality and adequate handling and storage procedures should precede and follow the processing. The paper concentrates on the first element of the HACCP system for an irradiation plant: the incoming product control, i.e. whether GMP of foods to be irradiated can be assessed by establishing microbiological criteria for their previous good manufacturing practice. In this regard, it summarizes considerations and findings of a ''Consultation on Microbiological Criteria for Foods to be Further Processed Including by Irradiation'' held in 1989 by the International Consultative Group on Food irradiation at the Headquarters of the World Health Organization, Geneva. Difficulties in establishing reference values and defining good manufacturing practices will be pointed out. (orig.)

  8. A comparison of HK-CONWIP and BK-CONWIP control strategies in a multi-product manufacturing system

    Directory of Open Access Journals (Sweden)

    Chukwunonyelum Emmanuel Onyeocha

    2015-12-01

    Full Text Available This paper evaluates the performance of the Hybrid Kanban Constant Work-In-Process control strategy and Basestock Kanban Constant Work-In-Process control strategy operating Shared Kanban Allocation Policy (S-KAP and Dedicated Kanban Allocation Policy (D-KAP in a multi-product serial flow line. We explored the effect of an increase of product types on the WIP inventory in the system. A simulation-based optimisation technique was used in determining the optimal settings for the strategies. The strategies were compared via pairwise comparison technique and Nelson’s ranking and selection procedure. S-KAP responds quicker to demand than D-KAP. BK-CONWIP outperforms HK-CONWIP in a serial manufacturing system. It was shown that an increase in the number of product-type increases the number of PAC and WIP inventory.

  9. Advances in battery manufacturing, service, and management systems

    CERN Document Server

    Zhou, Shiyu; Han, Yehui

    2016-01-01

    This book brings together experts in the field to highlight the cutting edge research advances in BM2S2 and to promote an innovative integrated research framework responding to the challenges. There are three major parts included in this book: manufacturing, service, and management. The first part focuses on battery manufacturing systems, including modeling, analysis, design and control, as well as economic and risk analyses. The second part focuses on information technology’s impact on service systems, such as data-driven reliability modeling, failure prognosis, and service decision making methodologies for battery services. The third part addresses battery management systems (BMS) for control and optimization of battery cells, opera ions, and hybrid storage systems to ensure overall performance and safety, as well as EV management.

  10. 21 CFR 113.5 - Current good manufacturing practice.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Current good manufacturing practice. 113.5 Section... CONTAINERS General Provisions § 113.5 Current good manufacturing practice. The criteria in §§ 113.10, 113.40..., methods, practices, and controls used by the commercial processor in the manufacture, processing, or...

  11. Laser additive manufacturing of high-performance materials

    CERN Document Server

    Gu, Dongdong

    2015-01-01

    This book entitled “Laser Additive Manufacturing of High-Performance Materials” covers the specific aspects of laser additive manufacturing of high-performance new materials components based on an unconventional materials incremental manufacturing philosophy, in terms of materials design and preparation, process control and optimization, and theories of physical and chemical metallurgy. This book describes the capabilities and characteristics of the development of new metallic materials components by laser additive manufacturing process, including nanostructured materials, in situ composite materials, particle reinforced metal matrix composites, etc. The topics presented in this book, similar as laser additive manufacturing technology itself, show a significant interdisciplinary feature, integrating laser technology, materials science, metallurgical engineering, and mechanical engineering. This is a book for researchers, students, practicing engineers, and manufacturing industry professionals interested i...

  12. Recent Advances in Precision Machinery and Manufacturing Technology

    DEFF Research Database (Denmark)

    Liu, Chien-Hung; Hsieh, Wen-Hsiang; Chang, Zong-Yu

    2014-01-01

    Precision machinery and manufacturing technology are be- coming more important in current and future technologies. New knowledge in this field will aid in the advancement of various technologies that are needed to gain industrial competitiveness. To this end, the special issue aims to disseminate...... the latest advancements of relevant fundamental and applied research works of high quality to the inter- national community. The topics of the accepted articles in the special issue include precision manufacturing pro- cesses, measurements and control, robotics and automation, machine tools, advanced...

  13. The Frontiers of Additive Manufacturing

    Energy Technology Data Exchange (ETDEWEB)

    Grote, Christopher John [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-03-03

    Additive manufacturing, more commonly known as 3-D printing, has become a ubiquitous tool in science for its precise control over mechanical design. For additive manufacturing to work, a 3-D structure is split into thin 2D slices, and then different physical properties, such as photo-polymerization or melting, are used to grow the sequential layers. The level of control allows not only for devices to be made with a variety of materials: e.g. plastics, metals, and quantum dots, but to also have finely controlled structures leading to other novel properties. While 3-D printing is widely used by hobbyists for making models, it also has industrial applications in structural engineering, biological tissue scaffolding, customized electric circuitry, fuel cells, security, and more.

  14. Achievement report on developing inverse manufacturing system in fiscal 1998; 1998 nendo inverse manufacturing system no kaihatsu seika hokokusho

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2000-03-01

    Research and development has been performed on a circulating type production system, or an inverse manufacturing system, to minimize the environmental load in the entire life cycle of industrial products from design to manufacturing, maintenance, recovery, and re-utilization. In developing the recycling information system, discussion and extraction were executed on the data to be exchanged between manufacturers and users in the inverse society. A new individual parts history control system was developed. In developing the recycling processing system, a prototype system was evaluated by using hypothetical data, wherein the possibility of improving the recycling processing efficiency and reducing the cost was verified. In addition, trial design was made on a recycling processing plant in consideration of the cost effect to get the future plant image. In fabricating the inverse manufacturing products, a prototype concept model was made for information terminal devices. Development was performed on such elementary technologies as the easy-to-disintegrate structure technology, self-integration connecting structure and environmental hysteresis detection system. (NEDO)

  15. Technological assessment of local manufacturers for wind turbine blade manufacturing in Pakistan

    Science.gov (United States)

    Mahmood, Khurram; Haroon, General

    2012-11-01

    Composite materials manufacturing industry is one of the world's hi-tech industry. Manufacturing of wind turbine blades is one of the specialized fields requiring high degree of precision and composite manufacturing techniques. This paper identifies the industries specializing in the composite manufacturing and is able to manufacture wind turbines blades in Pakistan. In the second phase, their technology readiness level is determined, based on some factors and then a readiness level are assigned to them. The assigned technology readiness level will depict the absorptive capacity of each manufacturing unit and its capability to take on such projects. The individual readiness level of manufacturing unit will then be used to establish combined technology readiness level of Pakistan particularly for wind turbine blades manufacturing. The composite manufacturing industry provides many spin offs and a diverse range of products can be manufactured using this facility. This research will be helpful to categorize the strong points and flaws of local industry for the gap analysis. It can also be used as a prerequisite study before the evaluation of technologies and specialties to improve the industry of the country for the most favorable results. This will form a basic data base which can be used for the decision making related to transfer of technology, training of local skilled workers and general up-gradation of the local manufacturing units.

  16. The impact of an employee wellness programme in clothing/textile manufacturing companies: a randomised controlled trial

    Directory of Open Access Journals (Sweden)

    Edries Naila

    2013-01-01

    Full Text Available Abstract Background The prevalence of health risk behaviours is growing amongst South African employees. Health risk behaviours have been identified as a major contributor to reduced health related quality of life (HRQoL and the increased prevalence of non-communicable diseases. Worksite wellness programmes promise to promote behaviour changes amongst employees and to improve their HRQoL. The aim of this study was to evaluate the short-term effects of an employee wellness programme on HRQoL, health behaviour change, body mass index (BMI and absenteeism amongst clothing and textile manufacturing employees. Methods The study used a randomised control trial design. The sample consisted of 80 subjects from three clothing manufacturing companies in Cape Town, South Africa. The experimental group was subjected to a wellness programme based on the principles of cognitive behaviour therapy (CBT as well as weekly supervised exercise classes over six weeks. The control group received a once-off health promotion talk and various educational pamphlets, with no further intervention. Measurements were recorded at baseline and at six weeks post-intervention. Outcome measures included the EQ-5D, Stanford Exercise Behaviours Scale, body mass index and absenteeism. Data was analysed with the Statistica-8 software program. Non-parametric tests were used to evaluate the differences in the medians between the two groups and to determine the level of significance. The Sign test was used to determine the within group changes. The Mann–Whitney U test was used to determine the difference between the two groups. Results At six weeks post intervention the experimental group (39 subjects demonstrated improvement in almost every parameter. In contrast, apart from an overall decrease in time off work and a reduction in BMI for all study participants, there was no significant change noted in the behaviour of the control group (41 subjects. Seventy percent of the

  17. Computer-Aided Manufacturing of 3D Workpieces

    OpenAIRE

    Cornelia Victoria Anghel Drugarin; Mihaela Dorica Stroia

    2017-01-01

    Computer-Aided Manufacturing (CAM) assumes to use dedicated software for controlling machine tools and similar devices in the process of workpieces manufacturing. CAM is, in fact, an application technology that uses computer software and machinery to simplify and automate manufacturing processes. CAM is the inheritor of computer-aided engineering (CAE) and is often used conjunctively with computer-aided design (CAD). Advanced CAM solutions are forthcoming and have a large ...

  18. 40 CFR 1042.130 - Installation instructions for vessel manufacturers.

    Science.gov (United States)

    2010-07-01

    ...) AIR POLLUTION CONTROLS CONTROL OF EMISSIONS FROM NEW AND IN-USE MARINE COMPRESSION-IGNITION ENGINES...-speed operation, tell vessel manufacturers not to install the engines in variable-speed applications or... vessel manufacturers. (a) If you sell an engine for someone else to install in a vessel, give the engine...

  19. Efficiency and Innovation in U.S. Manufacturing Energy Use

    Energy Technology Data Exchange (ETDEWEB)

    None

    2005-06-01

    The NAM has partnered with the Alliance to Save Energy to develop this booklet for manufacturers who want to achieve more strategic control over rising energy costs. Being better energy managers is important not only for each company, but is also an essential component in achieving a low-inflation, high-growth economy. We hope that the opportunities outlined in this booklet will encourage manufacturers to make energy efficiency a part of standard operating procedure.

  20. Post Processing Methods used to Improve Surface Finish of Products which are Manufactured by Additive Manufacturing Technologies: A Review

    Science.gov (United States)

    Kumbhar, N. N.; Mulay, A. V.

    2016-08-01

    The Additive Manufacturing (AM) processes open the possibility to go directly from Computer-Aided Design (CAD) to a physical prototype. These prototypes are used as test models before it is finalized as well as sometimes as a final product. Additive Manufacturing has many advantages over the traditional process used to develop a product such as allowing early customer involvement in product development, complex shape generation and also save time as well as money. Additive manufacturing also possess some special challenges that are usually worth overcoming such as Poor Surface quality, Physical Properties and use of specific raw material for manufacturing. To improve the surface quality several attempts had been made by controlling various process parameters of Additive manufacturing and also applying different post processing techniques on components manufactured by Additive manufacturing. The main objective of this work is to document an extensive literature review in the general area of post processing techniques which are used in Additive manufacturing.

  1. Tritium target manufacturing for use in accelerators

    Science.gov (United States)

    Bach, P.; Monnin, C.; Van Rompay, M.; Ballanger, A.

    2001-07-01

    As a neutron tube manufacturer, SODERN is now in charge of manufacturing tritium targets for accelerators, in cooperation with CEA/DAM/DTMN in Valduc. Specific deuterium and tritium targets are manufactured on request, according to the requirements of the users, starting from titanium target on copper substrate, and going to more sophisticated devices. A wide range of possible uses is covered, including thin targets for neutron calibration, thick targets with controlled loading of deuterium and tritium, rotating targets for higher lifetimes, or large size rotating targets for accelerators used in boron neutron therapy. Activity of targets lies in the 1 to 1000 Curie, diameter of targets being up to 30 cm. Special targets are also considered, including surface layer targets for lowering tritium desorption under irradiation, or those made from different kinds of occluders such as titanium, zirconium, erbium, scandium, with different substrates. It is then possible to optimize either neutron output, or lifetime and stability, or thermal behavior.

  2. Stochastic cooperative advertising in a manufacturer-retailer decentralized supply channel

    Science.gov (United States)

    Ezimadu, Peter E.; Nwozo, Chukwuma R.

    2017-03-01

    This work considers cooperative advertising in a manufacturer-retailer supply chain. While the manufacturer is the Stackelberg leader, the retailer is the follower. Using Sethi model it models the dynamic effect of the manufacturer and retailer's advertising efforts on sale. It uses optimal control technique and stochastic differential game theory to obtain the players' advertising strategies and the long-run value of the awareness share. Further, it models the relationship between the payoffs of both players and the awareness share. The work shows that with the provision of subsidy the retail advertising effort increases while the manufacturer's advertising effort reduces. It further shows that the total channel payoff is higher for subsidised retail advertising. However, the subsidy can only be possible if the rate of growth of the manufacturer's payoff is twice higher than that of the retailer.

  3. Process Control Strategies for Dual-Phase Steel Manufacturing Using ANN and ANFIS

    Science.gov (United States)

    Vafaeenezhad, H.; Ghanei, S.; Seyedein, S. H.; Beygi, H.; Mazinani, M.

    2014-11-01

    In this research, a comprehensive soft computational approach is presented for the analysis of the influencing parameters on manufacturing of dual-phase steels. A set of experimental data have been gathered to obtain the initial database used for the training and testing of both artificial neural networks (ANN) and adaptive neuro-fuzzy inference system (ANFIS). The parameters used in the strategy were intercritical annealing temperature, carbon content, and holding time which gives off martensite percentage as an output. A fraction of the data set was chosen to train both ANN and ANFIS, and the rest was put into practice to authenticate the act of the trained networks while seeing unseen data. To compare the obtained results, coefficient of determination and root mean squared error indexes were chosen. Using artificial intelligence methods, it is not necessary to consider and establish a preliminary mathematical model and formulate its affecting parameters on its definition. In conclusion, the martensite percentages corresponding to the manufacturing parameters can be determined prior to a production using these controlling algorithms. Although the results acquired from both ANN and ANFIS are very encouraging, the proposed ANFIS has enhanced performance over the ANN and takes better effect on cost-reduction profit.

  4. Detecting Attacks in CyberManufacturing Systems: Additive Manufacturing Example

    Directory of Open Access Journals (Sweden)

    Wu Mingtao

    2017-01-01

    Full Text Available CyberManufacturing System is a vision for future manufacturing where physical components are fully integrated with computational processes in a connected environment. However, realizing the vision requires that its security be adequately ensured. This paper presents a vision-based system to detect intentional attacks on additive manufacturing processes, utilizing machine learning techniques. Particularly, additive manufacturing systems have unique vulnerabilities to malicious attacks, which can result in defective infills but without affecting the exterior. In order to detect such infill defects, the research uses simulated 3D printing process images as well as actual 3D printing process images to compare accuracies of machine learning algorithms in classifying, clustering and detecting anomalies on different types of infills. Three algorithms - (i random forest, (ii k nearest neighbor, and (iii anomaly detection - have been adopted in the research and shown to be effective in detecting such defects.

  5. Case study of lean manufacturing application in a die casting manufacturing company

    Science.gov (United States)

    Ching, Ng Tan; Hoe, Clarence Chan Kok; Hong, Tang Sai; Ghobakhloo, Morteza; Pin, Chen Kah

    2015-05-01

    The case study of lean manufacturing aims to study the application of lean manufacturing in a die casting manufacturing company located in Pulau Penang, Malaysia. This case study describes mainly about the important concepts and applications of lean manufacturing which could gradually help the company in increasing the profit by studying and analyzing their current manufacturing process and company culture. Many approaches of lean manufacturing are studied in this project which includes: 5S housekeeping, Kaizen, and Takt Time. Besides, the lean tools mentioned, quality tool such as the House of Quality is being used as an analysis tool to continuously improve the product quality. In short, the existing lean culture in the company is studied and analyzed, with recommendations written at the end of this paper.

  6. Using microwave Doppler radar in automated manufacturing applications

    Science.gov (United States)

    Smith, Gregory C.

    Since the beginning of the Industrial Revolution, manufacturers worldwide have used automation to improve productivity, gain market share, and meet growing or changing consumer demand for manufactured products. To stimulate further industrial productivity, manufacturers need more advanced automation technologies: "smart" part handling systems, automated assembly machines, CNC machine tools, and industrial robots that use new sensor technologies, advanced control systems, and intelligent decision-making algorithms to "see," "hear," "feel," and "think" at the levels needed to handle complex manufacturing tasks without human intervention. The investigator's dissertation offers three methods that could help make "smart" CNC machine tools and industrial robots possible: (1) A method for detecting acoustic emission using a microwave Doppler radar detector, (2) A method for detecting tool wear on a CNC lathe using a Doppler radar detector, and (3) An online non-contact method for detecting industrial robot position errors using a microwave Doppler radar motion detector. The dissertation studies indicate that microwave Doppler radar could be quite useful in automated manufacturing applications. In particular, the methods developed may help solve two difficult problems that hinder further progress in automating manufacturing processes: (1) Automating metal-cutting operations on CNC machine tools by providing a reliable non-contact method for detecting tool wear, and (2) Fully automating robotic manufacturing tasks by providing a reliable low-cost non-contact method for detecting on-line position errors. In addition, the studies offer a general non-contact method for detecting acoustic emission that may be useful in many other manufacturing and non-manufacturing areas, as well (e.g., monitoring and nondestructively testing structures, materials, manufacturing processes, and devices). By advancing the state of the art in manufacturing automation, the studies may help

  7. The impact of fit manufacturing on green manufacturing: A review

    Science.gov (United States)

    Qi, Ang Nian; Sin, Tan Chan; Fathullah, M.; Lee, C. C.

    2017-09-01

    Fit manufacturing and Green manufacturing are a new trend principle and concept. They are getting popular in industrial. This paper is identifying the impact between Fit manufacturing and Green manufacturing. Besides Fit manufacturing, Lean manufacturing, Agile manufacturing and Sustainable manufacturing gives big impacts to Green Manufacturing. On top of that, this paper also discuss the benefits of applying Fit manufacturing and Green manufacturing in industrial as well as environment. Hence, applications of Fit manufacturing and Green Manufacturing are increasing year by year.

  8. Advanced manufacturing of microdisk vaccines for uniform control of material properties and immune cell function.

    Science.gov (United States)

    Zeng, Qin; Zhang, Peipei; Zeng, Xiangbin; Tostanoski, Lisa H; Jewell, Christopher M

    2017-12-19

    The continued challenges facing vaccines in infectious disease and cancer highlight a need for better control over the features of vaccines and the responses they generate. Biomaterials offer unique advantages to achieve this goal through features such as controlled release and co-delivery of antigens and adjuvants. However, many synthesis strategies lead to particles with heterogeneity in diameter, shape, loading level, or other properties. In contrast, advanced manufacturing techniques allow precision control of material properties at the micro- and nano-scale. These capabilities in vaccines and immunotherapies could allow more rational design to speed efficient design and clinical translation. Here we employed soft lithography to generate polymer microdisk vaccines with uniform structures and tunable compositions of vaccine antigens and toll like receptor agonists (TLRas) that serve as molecular adjuvants. Compared to conventional PLGA particles formed by emulsion, microdisks provided a dramatic improvement in the consistency of properties such as diameter. During culture with primary dendritic cells (DCs) from mice, microdisks were internalized by the cells without toxicity, while promoting co-delivery of antigen and TLRa to the same cell. Analysis of DC surface activation markers by flow cytometry revealed microdisk vaccines activated dendritic cells in a manner that depended on the level of TLRa, while antigen processing and presentation depended on the amount of antigen in the microdisks. Together, this work demonstrates the use of advanced manufacturing techniques to produce uniform vaccines that direct DC function depending on the composition in the disks.

  9. Regulatory Perspectives on Continuous Pharmaceutical Manufacturing: Moving From Theory to Practice: September 26-27, 2016, International Symposium on the Continuous Manufacturing of Pharmaceuticals.

    Science.gov (United States)

    Nasr, Moheb M; Krumme, Markus; Matsuda, Yoshihiro; Trout, Bernhardt L; Badman, Clive; Mascia, Salvatore; Cooney, Charles L; Jensen, Keith D; Florence, Alastair; Johnston, Craig; Konstantinov, Konstantin; Lee, Sau L

    2017-11-01

    Continuous manufacturing plays a key role in enabling the modernization of pharmaceutical manufacturing. The fate of this emerging technology will rely, in large part, on the regulatory implementation of this novel technology. This paper, which is based on the 2nd International Symposium on the Continuous Manufacturing of Pharmaceuticals, describes not only the advances that have taken place since the first International Symposium on Continuous Manufacturing of Pharmaceuticals in 2014, but the regulatory landscape that exists today. Key regulatory concepts including quality risk management, batch definition, control strategy, process monitoring and control, real-time release testing, data processing and management, and process validation/verification are outlined. Support from regulatory agencies, particularly in the form of the harmonization of regulatory expectations, will be crucial to the successful implementation of continuous manufacturing. Collaborative efforts, among academia, industry, and regulatory agencies, are the optimal solution for ensuring a solid future for this promising manufacturing technology. Copyright © 2017 American Pharmacists Association®. All rights reserved.

  10. PowerLight Corporation Lean Manufacturing, PV Manufacturing R&D Phase I Report: 6 December 2001--31 March 2003

    Energy Technology Data Exchange (ETDEWEB)

    Hargis, L; Botkin, J.

    2005-06-01

    PowerLight Corporation (PowerLight) has completed Phase I of its PV Manufacturing R&D subcontract, ''PowerGuard Lean Manufacturing,'' Subcontract No. NDO-1-30628-04. The overall technical goal of this project was to reduce the cost of PowerGuard manufacturing while simultaneously improving product quality. This will enable PowerLight to scale up production capacity as the market for PowerGuard continues to grow. Through the introduction of world-class lean manufacturing techniques, PowerLight was to cut out waste in the manufacturing process of PowerGuard. The manufacturing process was to be overhauled with an objective of removing as much as possible those steps that do not add value to the product. Quality of finished goods was also to be improved through the use of statistical process control and error-proofing in the manufacturing process. Factory operations were also to be addressed to streamline those factory activities that support the manufacturing process. This report de tails the progress made toward the above listed goals during the first phase of this subcontract.

  11. Support given by the manufacturer

    International Nuclear Information System (INIS)

    Schomer, E.

    1993-01-01

    As regards German NPP, the purchaser has the control function and the manufacturer the role of a general planner binding together all supply lots. Therefore the manufacturer possesses a very broad and thorough detailed knowledge of the plant functioning and becomes a life-long important partner of the plant. Such partnership requires from the manufacturer to provide continuously available and economical services to the plant; he must work purposefully in a quality-conscious and innovative way. This is his vision, and he will comply with it over the whole service life of the plant. The importance of services is illustrated by a large number of examples. (orig./DG) [de

  12. Design and application of reconfigurable manufacturing systems in agile mass customization manufacturing environment.

    CSIR Research Space (South Africa)

    Xing, B

    2007-05-01

    Full Text Available processes. Many manufacturing techniques are based on the principles of Flexible Manufacturing and Dedicated Manufacturing for mass production. Reconfigurable Manufacturing System, (RMS), is a manufacturing system that can provide for Agile Manufacturing...

  13. Opportunities and challenges of real-time release testing in biopharmaceutical manufacturing.

    Science.gov (United States)

    Jiang, Mo; Severson, Kristen A; Love, John Christopher; Madden, Helena; Swann, Patrick; Zang, Li; Braatz, Richard D

    2017-11-01

    Real-time release testing (RTRT) is defined as "the ability to evaluate and ensure the quality of in-process and/or final drug product based on process data, which typically includes a valid combination of measured material attributes and process controls" (ICH Q8[R2]). This article discusses sensors (process analytical technology, PAT) and control strategies that enable RTRT for the spectrum of critical quality attributes (CQAs) in biopharmaceutical manufacturing. Case studies from the small-molecule and biologic pharmaceutical industry are described to demonstrate how RTRT can be facilitated by integrated manufacturing and multivariable control strategies to ensure the quality of products. RTRT can enable increased assurance of product safety, efficacy, and quality-with improved productivity including faster release and potentially decreased costs-all of which improve the value to patients. To implement a complete RTRT solution, biologic drug manufacturers need to consider the special attributes of their industry, particularly sterility and the measurement of viral and microbial contamination. Continued advances in on-line and in-line sensor technologies are key for the biopharmaceutical manufacturing industry to achieve the potential of RTRT. Related article: http://onlinelibrary.wiley.com/doi/10.1002/bit.26378/full. © 2017 Wiley Periodicals, Inc.

  14. Additive manufacturing: From implants to organs

    African Journals Online (AJOL)

    Additive manufacturing (AM) constructs 3D objects layer by layer under computer control from 3D models. 3D printing is one ... anatomical models for surgery planning, and design and construction ... production of implants, particularly to replace bony structures, is ... Manufactured organs are, however, an elusive goal.

  15. Expert ratings of job demand and job control as predictors of injury and musculoskeletal disorder risk in a manufacturing cohort.

    Science.gov (United States)

    Cantley, Linda F; Tessier-Sherman, Baylah; Slade, Martin D; Galusha, Deron; Cullen, Mark R

    2016-04-01

    To examine associations between workplace injury and musculoskeletal disorder (MSD) risk and expert ratings of job-level psychosocial demand and job control, adjusting for job-level physical demand. Among a cohort of 9260 aluminium manufacturing workers in jobs for which expert ratings of job-level physical and psychological demand and control were obtained during the 2 years following rating obtainment, multivariate mixed effects models were used to estimate relative risk (RR) of minor injury and minor MSD, serious injury and MSD, minor MSD only and serious MSD only by tertile of demand and control, adjusting for physical demand as well as other recognised risk factors. Compared with workers in jobs rated as having low psychological demand, workers in jobs with high psychological demand had 49% greater risk of serious injury and serious MSD requiring medical treatment, work restrictions or lost work time (RR=1.49; 95% CI 1.10 to 2.01). Workers in jobs rated as having low control displayed increased risk for minor injury and minor MSD (RR=1.45; 95% CI 1.12 to 1.87) compared with those in jobs rated as having high control. Using expert ratings of job-level exposures, this study provides evidence that psychological job demand and job control contribute independently to injury and MSD risk in a blue-collar manufacturing cohort, and emphasises the importance of monitoring psychosocial workplace exposures in addition to physical workplace exposures to promote worker health and safety. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

  16. Good manufacturing practice

    International Nuclear Information System (INIS)

    Schlyer, D.J.

    2001-01-01

    In this presentation author deals with the Implementation of good manufacturing practice for radiopharmaceuticals. The presentation is divided into next parts: Batch size; Expiration date; QC Testing; Environmental concerns; Personnel aspects; Radiation concerns; Theoretical yields; Sterilizing filters; Control and reconciliation of materials and components; Product strength; In process sampling and testing; Holding and distribution; Drug product inspection; Buildings and facilities; Renovations at BNL for GMP; Aseptic processing and sterility assurance; Process validation and control; Quality control and drug product stability; Documentation and other GMP topics; Building design considerations; Equipment; and Summary

  17. Macro-/Micro-Controlled 3D Lithium-Ion Batteries via Additive Manufacturing and Electric Field Processing.

    Science.gov (United States)

    Li, Jie; Liang, Xinhua; Liou, Frank; Park, Jonghyun

    2018-01-30

    This paper presents a new concept for making battery electrodes that can simultaneously control macro-/micro-structures and help address current energy storage technology gaps and future energy storage requirements. Modern batteries are fabricated in the form of laminated structures that are composed of randomly mixed constituent materials. This randomness in conventional methods can provide a possibility of developing new breakthrough processing techniques to build well-organized structures that can improve battery performance. In the proposed processing, an electric field (EF) controls the microstructures of manganese-based electrodes, while additive manufacturing controls macro-3D structures and the integration of both scales. The synergistic control of micro-/macro-structures is a novel concept in energy material processing that has considerable potential for providing unprecedented control of electrode structures, thereby enhancing performance. Electrochemical tests have shown that these new electrodes exhibit superior performance in their specific capacity, areal capacity, and life cycle.

  18. Automatic exposure control in computed tomography - an evaluation of systems from different manufacturers

    Energy Technology Data Exchange (ETDEWEB)

    Soederberg, Marcus; Gunnarsson, Mikael (Dept. of Medical Radiation Physics, Skaane Univ. Hospital, Malmoe (Sweden)), e-mail: marcus.soderberg@med.lu.se

    2010-07-15

    Background: Today, practically all computed tomography (CT) systems are delivered with automatic exposure control (AEC) systems operating with tube current modulation in three dimensions. Each of these systems has different specifications and operates somewhat differently. Purpose: To evaluate AEC systems from four different CT scanner manufacturers: General Electric (GE), Philips, Siemens, and Toshiba, considering their potential for reducing radiation exposure to the patient while maintaining adequate image quality. Material and Methods: The dynamics (adaptation along the longitudinal axis) of tube current modulation of each AEC system were investigated by scanning an anthropomorphic chest phantom using both 16- and 64-slice CT scanners from each manufacturer with the AEC systems activated and inactivated. The radiation dose was estimated using the parameters in the DICOM image information and image quality was evaluated based on image noise (standard deviation of CT numbers) calculated in 0.5 cm2 circular regions of interest situated throughout the spine region of the chest phantom. Results: We found that tube current modulation dynamics were similar among the different AEC systems, especially between GE and Toshiba systems and between Philips and Siemens systems. Furthermore, the magnitude of the reduction in the exposure dose was considerable, in the range of 35-60%. However, in general the image noise increased when the AEC systems were used, especially in regions where the tube current was greatly decreased, such as the lung region. However, the variation in image noise among images obtained along the scanning direction was lower when using the AEC systems compared with fixed mAs. Conclusion: The AEC systems available in modern CT scanners can contribute to a significant reduction in radiation exposure to the patient and the image noise becomes more uniform within any given scan.

  19. An Assessment of Advanced Manufacturing Technologies Implementation in Manufacturing Enterprises

    Directory of Open Access Journals (Sweden)

    Ghulam Yasin Shaikh

    2011-04-01

    Full Text Available The implementation of AMTs (Advanced Manufacturing Technologies has always been the high interest and core issue for the manufacturing enterprises to get rapid production for global market place. The developed countries have achieved its competitive advantage by implementing this unique model of technologies with full range of systems. In developing countries, the implementation of such technologies is not much common due to so many reasons, (political, social, economical and technical but entrepreneurs of growing economies are contemplating to reshape long term strategy to adopt Computer systems oriented technologies in their manufacturing companies to meet the growing needs of their indigenous market on one hand and to make a place in the international market on the other. Although, very few manufacturing organization do meet the global market requirements. But there is still lot of efforts to be taken for world class competition. An attempt has been made in this paper to develop a conceptual model taking in to account the three parameters such as, Direct, Indirect and Administrative AMTs. This research work further attempts to present an empirical data analysis conducted in the manufacturing enterprises in province of Sindh, Pakistan. The overall indigenous progress of manufacturing enterprises as according to the data collected from 60 companies reveals that the AMTs systems are partially understood and practiced that is also one of the cause towards slow progress of national exchequer.

  20. Additive Manufacturing: Ensuring Quality for Spacecraft Applications

    Science.gov (United States)

    Swanson, Theodore; Stephenson, Timothy

    2014-01-01

    Reliable manufacturing requires that material properties and fabrication processes be well defined in order to insure that the manufactured parts meet specified requirements. While this issue is now relatively straightforward for traditional processes such as subtractive manufacturing and injection molding, this capability is still evolving for AM products. Hence, one of the principal challenges within AM is in qualifying and verifying source material properties and process control. This issue is particularly critical for applications in harsh environments and demanding applications, such as spacecraft.

  1. In-situ acoustic signature monitoring in additive manufacturing processes

    Science.gov (United States)

    Koester, Lucas W.; Taheri, Hossein; Bigelow, Timothy A.; Bond, Leonard J.; Faierson, Eric J.

    2018-04-01

    Additive manufacturing is a rapidly maturing process for the production of complex metallic, ceramic, polymeric, and composite components. The processes used are numerous, and with the complex geometries involved this can make quality control and standardization of the process and inspection difficult. Acoustic emission measurements have been used previously to monitor a number of processes including machining and welding. The authors have identified acoustic signature measurement as a potential means of monitoring metal additive manufacturing processes using process noise characteristics and those discrete acoustic emission events characteristic of defect growth, including cracks and delamination. Results of acoustic monitoring for a metal additive manufacturing process (directed energy deposition) are reported. The work investigated correlations between acoustic emissions and process noise with variations in machine state and deposition parameters, and provided proof of concept data that such correlations do exist.

  2. System of error detection in the manufacture of garments using artificial vision

    Science.gov (United States)

    Moreno, J. J.; Aguila, A.; Partida, E.; Martinez, C. L.; Morales, O.; Tejeida, R.

    2017-12-01

    A computer vision system is implemented to detect errors in the cutting stage within the manufacturing process of garments in the textile industry. It provides solution to errors within the process that cannot be easily detected by any employee, in addition to significantly increase the speed of quality review. In the textile industry as in many others, quality control is required in manufactured products and this has been carried out manually by means of visual inspection by employees over the years. For this reason, the objective of this project is to design a quality control system using computer vision to identify errors in the cutting stage within the garment manufacturing process to increase the productivity of textile processes by reducing costs.

  3. Manufacturing footprint optimisation: a necessity for manufacturing network in changing business environment

    DEFF Research Database (Denmark)

    Yang, Cheng; Farooq, Sami; Johansen, John

    2010-01-01

    Facing the unpredictable financial crisis, optimising the footprint can be the biggest and most important transformation a manufacturer can undertake. In order to realise the optimisation, fundamental understanding on manufacturing footprint is required. Different elements of manufacturing...... footprint have been investigated independently in the existing literature. In this paper, for the purpose of relationship exploration between different elements, manufacturing footprints of three industrial companies are traced historically. Based on them, four reasons for the transformation...

  4. 21 CFR 1303.23 - Procedure for fixing individual manufacturing quotas.

    Science.gov (United States)

    2010-04-01

    ...) In fixing individual manufacturing quotas for a basic class of controlled substance listed in Schedule I or II, the Administrator shall allocate to each applicant who is currently manufacturing such... quotas for a basic class of controlled substance listed in Schedule I or II, the Administrator shall...

  5. The RFID-Based Manufacturing and Inventory Revolution

    Institute of Scientific and Technical Information of China (English)

    HAMIDULLHKhanNiazi; SUNHou-fang; RIAZAhmed; SHAHIDIkramullahButt

    2005-01-01

    Radio frequency identification (RFID) is a contactless form of automatic identification and data capture (AIDC) technology. This paper explores the use of RFID in the new field of manufacturing automation and quality control. This paper consists of five parts. The first part gives a brief background and introduction of technology. The proposed use of RFID technology in the field of manufacturing automation and quality control is discussed in second part. The third part covers its use in the field of warehouse management system. Part four is a local review and analysis of RFID technology in manufacturing and warehousing which would support the potential use of this technology locally at China. The last part of paper gives concluding remarks about the RFID technology with recommendations of RFID use in these areas.

  6. The profit potential in reverse supply chain functions for catalyst manufacturers

    DEFF Research Database (Denmark)

    Larsen, Samuel; Sorth-Olsen, Rasmus; Honoré, Aske Lykke

    The reverse supply chain (RSC) contains inherent uncertainties, e.g. the quality level and return volume of used products. By contrast, the catalyst manufacturing industry is characterized by Certainty (manifested in e.g. well-defined and highly controlled production – processes and widespread...... standardization). This paper’s purpose is to examine whether RSC – processes can be profitably applied in this industry. Using case study research the paper examines which RSC - functions that are generally available to manufacturers are profitable for a selected catalyst manufacturer. Results show three...

  7. Manufacturing of biodrugs: need for harmonization in regulatory standards.

    Science.gov (United States)

    Sahoo, Niharika; Choudhury, Koel; Manchikanti, Padmavati

    2009-01-01

    Biodrugs (biologics) are much more complex than chemically synthesized drugs because of their structural heterogeneity and interactions within a given biologic system. The manufacturing process in the biodrug industry varies with each type of molecule and is far more elaborate and stringent due to the use of living organisms and complex substrates. Product purity and altered structural characteristics leading to potential immunogenicity have often been of concern when establishing quality and safety in the use of biodrugs. Regulatory compliance in manufacturing and commercialization of biodrugs involves quality control, quality assurance, and batch documentation. Many factors such as host cell development, cell bank establishment, cell culture, protein production, purification, analysis, formulation, storage, and handling are critical for ensuring the purity, activity, and safety of the finished product. Good Manufacturing Practice (GMP) for biodrugs has been developed in certain regions such as the EU, US, and Japan. Due to differences in manufacturing methods and systems, product-specific GMP guidelines are evolving. In general, there are variations in GMP guidelines between countries, which lead to difficulty for the manufacturers in conforming to different standards, thus entailing delays in the commercialization of biodrugs. There is a need to develop a unified regulatory guideline for biodrug manufacturing across various countries, which would be helpful in the marketing of products and trade. This review deals with the comparative framework and analysis of GMP regulation of biodrugs.

  8. The relationships between Lean manufacturing, management accounting and firm performance

    DEFF Research Database (Denmark)

    Kristensen, Thomas Borup; Nielsen, Henrik; Grasso, Lawrency

    2016-01-01

    with management accounting practices. Specifically, we document that Lean manufacturing is positively associated with Value Stream Costing, Lean visual controls and, more importantly, measures of labor and materials efficiency. Lean manufacturing is positively related to Lean thinking and both are positively...... associated with operational performance and so are Lean visual controls. We also document that the management accounting practices intervene affecting operational performance and they intervene with Lean thinking as well. Lastly, the relationship between Lean manufacturing and measures of labor and materials......Lean manufacturing has been adopted by numerous western companies as an answer to an increasing competitive environment. Lean manufacturing is seen as an enterprise-wide strategy encompassing a transformation of manufacturing practices, affecting companies’ management accounting practices and...

  9. quality assurance systems in nuclear fuel procurement and manufacturing

    International Nuclear Information System (INIS)

    Can, S.

    1997-01-01

    Quality is the totality of features and characteristics of a product or service that bear on its ability to satisfy stated or implied needs. Quality control is activities and techniques used to fulfill the requirements of quality. Quality assurance is a system and its main components are requirements. QA program, organization and responsibilities, design and verification, material and its control, manufacturing and process control, inspections, audits and documents: manuals, specifications, instructions. Quality assurance systems are largely based on ISO 9000 series of the International Standards Organization. ISO 9000 series has been adopted and published by Turkish Standards Institute as TS-ISO 9000. International Atomic Energy Agency also published a guide (50-SG-QA11) ''Quality Assurance in the Procurement, Design and Manufacture of Nuclear Fuel Assemblies'' in the safety guide series. In this study the role of quality control in quality assurance systems, inspection and test plans and acceptance and nonconformance quality levels will be explained in relation to nuclear fuel production. Examples of applications in quality assurance systems based on ISO 9000 will be given

  10. Soft computing in design and manufacturing of advanced materials

    Science.gov (United States)

    Cios, Krzysztof J.; Baaklini, George Y; Vary, Alex

    1993-01-01

    The potential of fuzzy sets and neural networks, often referred to as soft computing, for aiding in all aspects of manufacturing of advanced materials like ceramics is addressed. In design and manufacturing of advanced materials, it is desirable to find which of the many processing variables contribute most to the desired properties of the material. There is also interest in real time quality control of parameters that govern material properties during processing stages. The concepts of fuzzy sets and neural networks are briefly introduced and it is shown how they can be used in the design and manufacturing processes. These two computational methods are alternatives to other methods such as the Taguchi method. The two methods are demonstrated by using data collected at NASA Lewis Research Center. Future research directions are also discussed.

  11. IN718 Additive Manufacturing Properties and Influences

    Science.gov (United States)

    Lambert, Dennis M.

    2015-01-01

    The results of tensile, fracture, and fatigue testing of IN718 coupons produced using the selective laser melting (SLM) additive manufacturing technique are presented. The data has been "generalized" to remove the numerical values, although certain references to material standards are provided. This document provides some knowledge of the effect of variation of controlled build parameters used in the SLM process, a snapshot of the capabilities of SLM in industry at present, and shares some of the lessons learned along the way. For the build parameter characterization, the parameters were varied over a range about the machine manufacturer's recommended value, and in each case they were varied individually, although some co-variance of those parameters would be expected. SLM-produced IN718, tensile, fracture, and high-cycle fatigue properties equivalent to wrought IN718 are achievable. Build and post-build processes need to be determined and then controlled to established limits to accomplish this. It is recommended that a multi-variable evaluation, e.g., design-of-experiment (DOE), of the build parameters be performed to better evaluate the co-variance of the parameters.

  12. Social manufacturing

    OpenAIRE

    Hamalainen, Markko; Karjalainen, Jesse

    2017-01-01

    New business models harnessing the power of individuals have already revolutionized service industries and digital content production. In this study, we investigate whether a similar phenomenon is taking place in manufacturing industries. We start by conceptually defining two distinct forms of firm-individual collaboration in manufacturing industries: (1) social cloud manufacturing, in which firms outsource manufacturing to individuals, and (2) social platform manufacturing, in which firms pr...

  13. IDENTIFICATION OF FACTORS AFFECTING LEAN MANUFACTURING IMPLEMENTATION IN PUMP MANUFACTURING COMPANIES IN INDIA - A CASE STUDY

    Directory of Open Access Journals (Sweden)

    Pratik Badgujar

    2016-09-01

    Full Text Available Lean Manufacturing has now become a common word in the industrial corridors. It has now been applied to the industries of several domains. No wonder that the Pump manufacturing has also witnessed profound influence of Lean philosophy. Pump manufacturing in India has a history as old as 80 years with more than 500 pump manufacturing units presently working. The present research is an explorative study and was undertaken to identify various factors affecting lean manufacturing implementation in pump manufacturing industry. Analysis of results revealed that the companies registered increase in productivity and reduction in costs and wastes. Lack of understanding, Supply chain and Company culture are found to be the strongest barriers of lean manufacturing implementation. The multiple regression model revealed that Lack of workers support can be fairly reduced by educating them about Lean Manufacturing and establishing a healthy communication with workers. An analysis across different management levels revealed disparity in perceptions and views of personnel. There is a need for top management to align organization toward common goals so as to achieve better success in implementing lean manufacturing.

  14. Knowledge Transfer and Manufacturing Relocation in International Manufacturing Networks

    DEFF Research Database (Denmark)

    Madsen, Erik Skov

    2014-01-01

    This paper is built on six longitudinal case studies of knowledge transfer in manufacturing relocation. By focusing on tacit and explicit knowledge the paper introduces a model for identification of knowledge in relation to four task situations on the shop floor in a manufacturing environment...... after relocation. Finally the paper discusses how “dispatching capacity” and “absorptive capacity” can improve the process....

  15. Simulation approach towards energy flexible manufacturing systems

    CERN Document Server

    Beier, Jan

    2017-01-01

    This authored monograph provides in-depth analysis and methods for aligning electricity demand of manufacturing systems to VRE supply. The book broaches both long-term system changes and real-time manufacturing execution and control, and the author presents a concept with different options for improved energy flexibility including battery, compressed air and embodied energy storage. The reader will also find a detailed application procedure as well as an implementation into a simulation prototype software. The book concludes with two case studies. The target audience primarily comprises research experts in the field of green manufacturing systems. .

  16. Commercial Implementation of Model-Based Manufacturing of Nanostructured Metals

    Energy Technology Data Exchange (ETDEWEB)

    Lowe, Terry C. [Los Alamos National Laboratory

    2012-07-24

    Computational modeling is an essential tool for commercial production of nanostructured metals. Strength is limited by imperfections at the high strength levels that are achievable in nanostructured metals. Processing to achieve homogeneity at the micro- and nano-scales is critical. Manufacturing of nanostructured metals is intrinsically a multi-scale problem. Manufacturing of nanostructured metal products requires computer control, monitoring and modeling. Large scale manufacturing of bulk nanostructured metals by Severe Plastic Deformation is a multi-scale problem. Computational modeling at all scales is essential. Multiple scales of modeling must be integrated to predict and control nanostructural, microstructural, macrostructural product characteristics and production processes.

  17. 21 CFR 1303.22 - Procedure for applying for individual manufacturing quotas.

    Science.gov (United States)

    2010-04-01

    ... manufacturing quotas. Any person who is registered to manufacture any basic class of controlled substance listed in Schedule I or II and who desires to manufacture a quantity of such class shall apply on DEA Form 189 for a manufacturing quota for such quantity of such class. Copies of DEA Form 189 may be obtained...

  18. Building API manufacturing in South Africa

    CSIR Research Space (South Africa)

    Loots, Glaudina

    2017-10-01

    Full Text Available projects) Challenges • Lack of relevant skills – process chemistry, process engineering (cGMP standards), project engineering, project management, process operations, maintenance and process quality control and assurance. – platform for skills... development - to enable a sustained pipeline of multidisciplinary skills for the envisaged API industry expansion. – entrepreneurial thinking – attract young talent in establishing niche businesses within the API manufacturing sector. • Small local...

  19. 21 CFR 129.1 - Current good manufacturing practice.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Current good manufacturing practice. 129.1 Section... Current good manufacturing practice. The applicable criteria in part 110 of this chapter, as well as the..., methods, practices, and controls used in the processing, bottling, holding, and shipping of bottled...

  20. Fully Disposable Manufacturing Concepts for Clinical and Commercial Manufacturing and Ballroom Concepts.

    Science.gov (United States)

    Boedeker, Berthold; Goldstein, Adam; Mahajan, Ekta

    2017-11-04

    The availability and use of pre-sterilized disposables has greatly changed the methods used in biopharmaceuticals development and production, particularly from mammalian cell culture. Nowadays, almost all process steps from cell expansion, fermentation, cell removal, and purification to formulation and storage of drug substances can be carried out in disposables, although there are still limitations with single-use technologies, particularly in the areas of pretesting and quality control of disposables, bag and connections standardization and qualification, extractables and leachables (E/L) validation, and dependency on individual vendors. The current status of single-use technologies is summarized for all process unit operations using a standard mAb process as an example. In addition, current pros and cons of using disposables are addressed in a comparative way, including quality control and E/L validation.The continuing progress in developing single-use technologies has an important impact on manufacturing facilities, resulting in much faster, less expensive and simpler plant design, start-up, and operation, because cell culture process steps are no longer performed in hard-piped unit operations. This leads to simpler operations in a lab-like environment. Overall it enriches the current landscape of available facilities from standard hard-piped to hard-piped/disposables hybrid to completely single-use-based production plants using the current segregation and containment concept. At the top, disposables in combination with completely and functionally closed systems facilitate a new, revolutionary design of ballroom facilities without or with much less segregation, which enables us to perform good manufacturing practice manufacturing of different products simultaneously in unclassified but controlled areas.Finally, single-use processing in lab-like shell facilities is a big enabler of transferring and establishing production in emergent countries, and this is

  1. A Multi-Component Automated Laser-Origami System for Cyber-Manufacturing

    Science.gov (United States)

    Ko, Woo-Hyun; Srinivasa, Arun; Kumar, P. R.

    2017-12-01

    Cyber-manufacturing systems can be enhanced by an integrated network architecture that is easily configurable, reliable, and scalable. We consider a cyber-physical system for use in an origami-type laser-based custom manufacturing machine employing folding and cutting of sheet material to manufacture 3D objects. We have developed such a system for use in a laser-based autonomous custom manufacturing machine equipped with real-time sensing and control. The basic elements in the architecture are built around the laser processing machine. They include a sensing system to estimate the state of the workpiece, a control system determining control inputs for a laser system based on the estimated data and user’s job requests, a robotic arm manipulating the workpiece in the work space, and middleware, named Etherware, supporting the communication among the systems. We demonstrate automated 3D laser cutting and bending to fabricate a 3D product as an experimental result.

  2. Control of formaldehyde and TVOC emission from wood-based flooring composites at various manufacturing processes by surface finishing.

    Science.gov (United States)

    Kim, Sumin

    2010-04-15

    This paper assesses the reproducibility of testing formaldehyde and TVOC emission behavior from wood flooring composites bonded by urea-formaldehyde resin at various manufacturing steps for surface finishing materials. The surface adhesion step of laminate flooring for this research was divided into two steps; HDF only and HDF with LPMs. In the case of engineered flooring, the manufacturing steps were divided into three steps; plywood only, fancy veneer bonded on plywood and UV coated on fancy veneer with plywood. Formaldehyde and VOCs emission decreased at the process of final surface finishing materials; LPMs were applied on the surface of HDF for laminate flooring. Although emissions increased when fancy veneer was bonded onto plywood in the case of engineered flooring, emission was dramatically reduced up to similar level with plywood only when final surface finishing; UV-curable coating was applied on fancy veneer. This study suggests that formaldehyde and VOCs emission from floorings can be controlled at manufacturing steps for surface finishing. 2009 Elsevier B.V. All rights reserved.

  3. The effectiveness of lean manufacturing audits in measuring operational performance improvements

    Directory of Open Access Journals (Sweden)

    Taggart, P.

    2013-08-01

    Full Text Available The hypothesis that lean manufacturing audits are an effective way to measure improvements in operational performance was tested using 64 manufacturing sites owned by a FTSE 100 company. Commonly-used lean characteristics were evaluated: policy deployment, standardised work, visual management and housekeeping, quick changeover techniques, total productive maintenance, continuous improvement (kaizen, error proofing, cultural awareness, material control, and levelling (heijunka. Operational performance was assessed employing commonly-used operational performance measures: on-time-delivery, inventory turns, and direct labour utilisation. The findings are that lean manufacturing audits are effective in measuring improvements in operational performance provided that the audit scope and the lean characteristics are aligned up front.

  4. Precision manufacturing

    CERN Document Server

    Dornfeld, David

    2008-01-01

    Today there is a high demand for high-precision products. The manufacturing processes are now highly sophisticated and derive from a specialized genre called precision engineering. Precision Manufacturing provides an introduction to precision engineering and manufacturing with an emphasis on the design and performance of precision machines and machine tools, metrology, tooling elements, machine structures, sources of error, precision machining processes and precision process planning. As well as discussing the critical role precision machine design for manufacturing has had in technological developments over the last few hundred years. In addition, the influence of sustainable manufacturing requirements in precision processes is introduced. Drawing upon years of practical experience and using numerous examples and illustrative applications, David Dornfeld and Dae-Eun Lee cover precision manufacturing as it applies to: The importance of measurement and metrology in the context of Precision Manufacturing. Th...

  5. Establishing a LEU MTR fuel manufacturing facility in South Africa

    International Nuclear Information System (INIS)

    Jamie, R.W.; Kocher, A.

    2010-01-01

    The South African MTR Fuel Manufacturing Facility was established in the 1970's to supply SAFARI-1 with Fuel Elements and Control Rods. South African capability was developed in parallel with the uranium enrichment program to meet the needs of the Reactor. Further to the July 2005 decision by the South African Governmnent to convert both SAFARI-1 and the Fuel Plant to LEU, the SAFARI-1 phase has been successfully completed and Necsa has commenced with the conversion of the MTR Fuel Manufacturing Facility. In order to establish, validate and qualify the facility, Necsa has entered into a co-operation and technology transfer agreement with AREVA CERCA, the French manufacturer of Research Reactor fuel elements. Past experiences, conversion challenges and the status of the MTR Fuel Facility Project are discussed. On-going co-operation with AREVA CERCA to implement the local manufacture of LEU fuel is explained and elaborated on. (author)

  6. Managing IT infrastructure standardisation in the networked manufacturing firm

    NARCIS (Netherlands)

    Akkermans, H.A.; Horst, van der H.

    2002-01-01

    This paper discusses managerial aspects of information technology (IT) infrastructure standardisation in networked manufacturing firms. It shows that in these firms, where local initiative is very important and strict central hierarchical control is lacking, standardisation of IT infrastructure is

  7. 77 FR 70189 - Manufacturer of Controlled Substances; Notice of Registration; Cayman Chemical Company

    Science.gov (United States)

    2012-11-23

    ... propylthiophenethylamine (7348). Marihuana (7360) I Tetrahydrocannabinols (7370) I Mescaline (7381) I 3,4,5... manufacture small quantities of marihuana derivatives for research purposes. In reference to drug code 7360 (Marihuana), the company plans to bulk manufacture cannabidiol. In reference to drug code 7370...

  8. Recent advances in fuel product and manufacturing process development

    International Nuclear Information System (INIS)

    Slember, R.J.; Doshi, P.K.

    1987-01-01

    This paper discusses advancements in commercial nuclear fuel products and manufacturing made by the Westinghouse Electric Corporation in response to the commercial nuclear fuel industry's demand for high reliability, increased plant availability and improved operating flexibility. The features and benefits of Westinghouse's most advanced fuel products--VANTAGE 5 for PWR plants and QUAD+ for BWR plants--are described, as well as 'high performance' fuel concepts now under development for delivery in the late 1980s. The paper also disusses the importance of in-process quality control throughout manufacturing towards reducing product variability and improving fuel reliability. (author)

  9. Revenue Management in Make-To-Order Manufacturing: Case Study of Capacity Control at ThyssenKrupp VDM

    Directory of Open Access Journals (Sweden)

    André Hintsches

    2010-10-01

    Full Text Available While revenue management (RM is traditionally considered a tool of service operations, RM shows considerable potential for application in manufacturing operations. The typical challenges in make-to-order manufacturing are fixed manufacturing capacities and a great variety in offered products, going along with pronounced fluctuations in demand and profitability. Since Harris and Pinder in the mid-90s, numerous papers have furthered the understanding of RM theory in this environment. Nevertheless, results to be expected from applying the developed methods to a practical industry setting have yet to be reported. To this end, this paper investigates a possible application of RM at ThyssenKrupp VDM, leading to considerable improvements in several areas.

  10. Manufacturing network evolution

    DEFF Research Database (Denmark)

    Yang, Cheng; Farooq, Sami; Johansen, John

    2011-01-01

    Purpose – This paper examines the effect of changes at the manufacturing plant level on other plants in the manufacturing network and also investigates the role of manufacturing plants on the evolution of a manufacturing network. Design/methodology/approach –The research questions are developed...... different manufacturing plants in the network and their impact on network transformation. Findings – The paper highlights the dominant role of manufacturing plants in the continuously changing shape of a manufacturing network. The paper demonstrates that a product or process change at one manufacturing...... by identifying the gaps in the reviewed literature. The paper is based on three case studies undertaken in Danish manufacturing companies to explore in detail their manufacturing plants and networks. The cases provide a sound basis for developing the research questions and explaining the interaction between...

  11. 77 FR 47115 - Manufacturer of Controlled Substances; Notice of Application; Cayman Chemical Company

    Science.gov (United States)

    2012-08-07

    ...)-propylthiophenethylamine I (7348). Marihuana (7360) I Tetrahydrocannabinols (7370) I Mescaline (7381) I 3,4,5... (1205) II The company plans to manufacture small quantities of marihuana derivatives for research purposes. In reference to drug code 7360 (Marihuana), the company plans to bulk manufacture cannabidiol. In...

  12. US manufacturing imports from China and employment in the Mexican manufacturing sector

    Directory of Open Access Journals (Sweden)

    Jorge Eduardo Mendoza Cota

    2016-09-01

    Full Text Available Since 2001 the manufacturing sector of Mexico has experienced a reduced growth rate. This study estimates the impact of U.S. and Chinese industrial activity on the demand for labor in the manufacturing sector of Mexico. With data on industrial activity, Chinese exports, wages and the peso-dollar exchange rate, a time series cointegration model is developed. The results show that exports from China to the USA and manufacturing wages have affected labor demand negatively, while factors such as the U.S. industrial production and the exchange rate tend to encourage manufacturing activity.

  13. 21 CFR 120.5 - Current good manufacturing practice.

    Science.gov (United States)

    2010-04-01

    ... 21 Food and Drugs 2 2010-04-01 2010-04-01 false Current good manufacturing practice. 120.5 Section... Provisions § 120.5 Current good manufacturing practice. Part 110 of this chapter applies in determining whether the facilities, methods, practices, and controls used to process juice are safe, and whether the...

  14. Field Evaluation of Advances in Energy-Efficiency Practices for Manufactured Homes

    Energy Technology Data Exchange (ETDEWEB)

    Levy, E. [Advanced Residential Integrated Energy Solutions (ARIES) Collaborative, New York, NY (United States); Dentz, J. [Advanced Residential Integrated Energy Solutions (ARIES) Collaborative, New York, NY (United States); Ansanelli, E. [Advanced Residential Integrated Energy Solutions (ARIES) Collaborative, New York, NY (United States); Barker, G. [Advanced Residential Integrated Energy Solutions (ARIES) Collaborative, New York, NY (United States); Rath, P. [Advanced Residential Integrated Energy Solutions (ARIES) Collaborative, New York, NY (United States); Dadia, D. [Advanced Residential Integrated Energy Solutions (ARIES) Collaborative, New York, NY (United States)

    2016-03-01

    Through field-testing and analysis, this project evaluated whole-building approaches and estimated the relative contributions of select technologies toward reducing energy use related to space conditioning in new manufactured homes. Three lab houses of varying designs were built and tested side-by-side under controlled conditions in Russellville, Alabama. The tests provided a valuable indicator of how changes in the construction of manufactured homes can contribute to significant reductions in energy use.

  15. Description of Manufacture - Optical Elements for Five Control Instruments

    Science.gov (United States)

    1951-04-01

    Locating Locating Shell,—The function of the locat- ing shell is to hold the lenses in the proper position during the blocking operation. Theo ...London: MäcMillan and Co., Ltd., 1931. Eisenhart , M. Herbert and Melson, E. W. "Development and Manufacture cf Optical Glass in America," Scientific

  16. Manufacturing technology and process for BWR fuel

    International Nuclear Information System (INIS)

    Kato, Shigeru

    1996-01-01

    Following recent advanced technologies, processes and requests of the design changes of BWR fuel, Nuclear Fuel Industries, Ltd. (NFI) has upgraded the manufacturing technology and honed its own skills to complete its brand-new automated facility in Tokai in the latter half of 1980's. The plant uses various forms of automation throughout the manufacturing process: the acceptance of uranium dioxide powder, pelletizing, fuel rod assembling, fuel bundle assembling and shipment. All processes are well computerized and linked together to establish the integrated control system with three levels of Production and Quality Control, Process Control and Process Automation. This multi-level system plays an important role in the quality assurance system which generates the highest quality of fuels and other benefits. (author)

  17. Metrological assurance and traceability for Industry 4.0 and additive manufacturing in Ukraine

    Science.gov (United States)

    Skliarov, Volodymyr; Neyezhmakov, Pavel; Prokopov, Alexander

    2018-03-01

    The national measurement standards from the point of view of traceability of the results of measurement in additive manufacturing in Ukraine are considered in the paper. The metrological characteristics of the national primary measurement standards in the field of geometric, temperature, optical-physical and time-frequency measurements, which took part in international comparisons within COOMET projects, are presented. The accurate geometric, temperature, optical-physical and time-frequency measurements are the key ones in controlling the quality of additive manufacturing. The use of advanced CAD/CAE/CAM systems allows to simulate the process of additive manufacturing at each stage. In accordance with the areas of the technology of additive manufacturing, the ways of improving the national measurement standards of Ukraine for the growing needs of metrology of additive manufacturing are considered.

  18. 78 FR 11611 - Current Good Manufacturing Practice and Hazard Analysis and Risk-Based Preventive Controls for...

    Science.gov (United States)

    2013-02-19

    ... related to the proposed rule on ``Current Good Manufacturing Practice and Hazard Analysis and Risk-Based... . All comments should be identified with the title ``Current Good Manufacturing Practice and Hazard... rulemaking to modernize the regulation for ``Current Good Manufacturing Practice In Manufacturing, Packing...

  19. IN718 Additive Manufacturing Properties and Influences

    Science.gov (United States)

    Lambert, Dennis M.

    2015-01-01

    The results of tensile, fracture, and fatigue testing of IN718 coupons produced using the selective laser melting (SLM) additive manufacturing technique are presented. The data have been "sanitized" to remove the numerical values, although certain references to material standards are provided. This document provides some knowledge of the effect of variation of controlled build parameters used in the SLM process, a snapshot of the capabilities of SLM in industry at present, and shares some of the lessons learned along the way. For the build parameter characterization, the parameters were varied over a range that was centered about the machine manufacturer's recommended value, and in each case they were varied individually, although some co-variance of those parameters would be expected. Tensile, fracture, and high-cycle fatigue properties equivalent to wrought IN718 are achievable with SLM-produced IN718. Build and post-build processes need to be determined and then controlled to established limits to accomplish this. It is recommended that a multi-variable evaluation, e.g., design-of experiment (DOE), of the build parameters be performed to better evaluate the co-variance of the parameters.

  20. The Current State of Sensing, Health Management, and Control for Small-To-Medium-Sized Manufacturers.

    Science.gov (United States)

    Helu, Moneer; Weiss, Brian

    2016-01-01

    The development of digital technologies for manufacturing has been challenged by the difficulty of navigating the breadth of new technologies available to industry. This difficulty is compounded by technologies developed without a good understanding of the capabilities and limitations of the manufacturing environment, especially within small-to-medium enterprises (SMEs). This paper describes industrial case studies conducted to identify the needs, priorities, and constraints of manufacturing SMEs in the areas of performance measurement, condition monitoring, diagnosis, and prognosis. These case studies focused on contract and original equipment manufacturers with less than 500 employees from several industrial sectors. Solution and equipment providers and National Institute of Standards and Technology (NIST) Hollings Manufacturing Extension Partnership (MEP) centers were also included. Each case study involved discussions with key shop-floor personnel as well as site visits with some participants. The case studies highlight SME's strong need for access to appropriate data to better understand and plan manufacturing operations. They also help define industrially-relevant use cases in several areas of manufacturing operations, including scheduling support, maintenance planning, resource budgeting, and workforce augmentation.

  1. The Future of Pharmaceutical Manufacturing Sciences

    DEFF Research Database (Denmark)

    Rantanen, Jukka; Khinast, Johannes

    2015-01-01

    The entire pharmaceutical sector is in an urgent need of both innovative technological solutions and fundamental scientific work, enabling the production of highly engineered drug products. Commercial-scale manufacturing of complex drug delivery systems (DDSs) using the existing technologies...... is challenging. This review covers important elements of manufacturing sciences, beginning with risk management strategies and design of experiments (DoE) techniques. Experimental techniques should, where possible, be supported by computational approaches. With that regard, state-of-art mechanistic process...... control solutions. Last part of the review addresses future manufacturing solutions, covering continuous processing and, specifically, hot-melt processing and printing-based technologies. Finally, challenges related to implementing these technologies as a part of future health care systems are discussed....

  2. Reconfigurability of behavioural specifications for manufacturing systems

    Science.gov (United States)

    Schmidt, Klaus Werner

    2017-12-01

    Reconfigurable manufacturing systems (RMS) support flexibility in the product variety and the configuration of the manufacturing system itself in order to enable quick adjustments to new products and production requirements. As a consequence, an essential feature of RMS is their ability to rapidly modify the control strategy during run-time. In this paper, the particular problem of changing the specified operation of a RMS, whose logical behaviour is modelled as a finite state automaton, is addressed. The notion of reconfigurability of specifications (RoS) is introduced and it is shown that the stated reconfiguration problem can be formulated as a controlled language convergence problem. In addition, algorithms for the verification of RoS and the construction of a reconfiguration supervisor are proposed. The supervisor is realised in a modular way which facilitates the extension by new configurations. Finally, it is shown that a supremal nonblocking and controllable strict subautomaton of the plant automaton that fulfils RoS exists in case RoS is violated for the plant automaton itself and an algorithm for the computation of this strict subautomaton is presented. The developed concepts and results are illustrated by a manufacturing cell example.

  3. The use of fatigue tests in the manufacture of automotive steel wheels.

    Science.gov (United States)

    Drozyner, P.; Rychlik, A.

    2016-08-01

    Production for the automotive industry must be particularly sensitive to the aspect of safety and reliability of manufactured components. One of such element is the rim, where durability is a feature which significantly affects the safety of transport. Customer complaints regarding this element are particularly painful for the manufacturer because it is almost always associated with the event of accident or near-accident. Authors propose original comprehensive method of quality control at selected stages of rims production: supply of materials, production and pre-shipment inspections. Tests by the proposed method are carried out on the originally designed inertial fatigue machine The machine allows bending fatigue tests in the frequency range of 0 to 50 Hz at controlled increments of vibration amplitude. The method has been positively verified in one of rims factory in Poland. Implementation resulted in an almost complete elimination of complaints resulting from manufacturing and material errors.

  4. Challenges in teaching modern manufacturing technologies

    Science.gov (United States)

    Ngaile, Gracious; Wang, Jyhwen; Gau, Jenn-Terng

    2015-07-01

    Teaching of manufacturing courses for undergraduate engineering students has become a challenge due to industrial globalisation coupled with influx of new innovations, technologies, customer-driven products. This paper discusses development of a modern manufacturing course taught concurrently in three institutions where students collaborate in executing various projects. Lectures are developed to contain materials featuring advanced manufacturing technologies, R&D trends in manufacturing. Pre- and post-surveys were conducted by an external evaluator to assess the impact of the course on increase in student's knowledge of manufacturing; increase students' preparedness and confidence in effective communication and; increase students' interest in pursuing additional academic studies and/or a career path in manufacturing and high technology. The surveyed data indicate that the students perceived significant gains in manufacturing knowledge and preparedness in effective communication. The study also shows that implementation of a collaborative course within multiple institutions requires a robust and collective communication platform.

  5. Designing an in-situ ultrasonic nondestructive evaluation system for ultrasonic additive manufacturing

    Science.gov (United States)

    Nadimpalli, Venkata K.; Nagy, Peter B.

    2018-04-01

    Ultrasonic Additive Manufacturing (UAM) is a solid-state layer by layer manufacturing process that utilizes vibration induced plastic deformation to form a metallurgical bond between a thin layer and an existing base structure. Due to the vibration based bonding mechanism, the quality of components at each layer depends on the geometry of the structure. In-situ monitoring during and between UAM manufacturing steps offers the potential for closed-loop control to optimize process parameters and to repair existing defects. One interface that is most prone to delamination is the base/build interface and often UAM component height and quality are limited by failure at the base/build interface. Low manufacturing temperatures and favorable orientation of typical interface defects in UAM make ultrasonic NDE an attractive candidate for online monitoring. Two approaches for in-situ NDE are discussed and the design of the monitoring system optimized so that the quality of UAM components is not affected by the addition of the NDE setup. Preliminary results from in-situ ultrasonic NDE indicate the potential to be utilized for online qualification, closed-loop control and offline certification of UAM components.

  6. Implementation Issues and Challenges in Applying Lean Manufacturing Tools & Techniques in Different Manufacturing Environments

    OpenAIRE

    Low, Kwee Ang

    2005-01-01

    Lean Manufacturing has made a significant impact on both the academic and manufacturing circles in the last decade. Fostered by a rapid spread into many other industrial sectors beyond the automotive industry, there has been significant development and "localisation" of the Lean Manufacturing concept in both developed and developing countries worldwide. Despite its successful application in a wide range of industries, little research has been carried out on its successful application outside ...

  7. Ramp Technology and Intelligent Processing in Small Manufacturing

    Science.gov (United States)

    Rentz, Richard E.

    1992-01-01

    To address the issues of excessive inventories and increasing procurement lead times, the Navy is actively pursuing flexible computer integrated manufacturing (FCIM) technologies, integrated by communication networks to respond rapidly to its requirements for parts. The Rapid Acquisition of Manufactured Parts (RAMP) program, initiated in 1986, is an integral part of this effort. The RAMP program's goal is to reduce the current average production lead times experienced by the Navy's inventory control points by a factor of 90 percent. The manufacturing engineering component of the RAMP architecture utilizes an intelligent processing technology built around a knowledge-based shell provided by ICAD, Inc. Rules and data bases in the software simulate an expert manufacturing planner's knowledge of shop processes and equipment. This expert system can use Product Data Exchange using STEP (PDES) data to determine what features the required part has, what material is required to manufacture it, what machines and tools are needed, and how the part should be held (fixtured) for machining, among other factors. The program's rule base then indicates, for example, how to make each feature, in what order to make it, and to which machines on the shop floor the part should be routed for processing. This information becomes part of the shop work order. The process planning function under RAMP greatly reduces the time and effort required to complete a process plan. Since the PDES file that drives the intelligent processing is 100 percent complete and accurate to start with, the potential for costly errors is greatly diminished.

  8. WASTE MINIMIZATION ASSESSMENT FOR A MANUFACTURER OF SILICON-CONTROLLED RECTIFIERS AND SCHOTTKY RECTIFIERS

    Science.gov (United States)

    The U.S. Environmental Protection Agency (EPA) has funded a pilot project to assist small- and medium-size manufacturers who want to minimize their generation of waste but who lack the expertise to do so. In an effort to assist these manufacturers Waste Minimization Assessment Ce...

  9. Designing and Manufacturing a Noise Controlling Silencer for the Cooling Tower Pump of Sarcheshmeh Copper Power Station

    Directory of Open Access Journals (Sweden)

    Sajad Zare

    2017-08-01

    Full Text Available Background One of the most common harmful factors in the workplace is noise. Noise control is a factor beneficial for health and safety in the workplace. Objectives The current study aimed to design and manufacture a silencer for the cooling tower pump of Sarcheshmeh Copper power station in order to control noise. Methods In this study, sound pressure level was measured by the use of a sound level meter (B & K 2260. Measurement was carried out in the light of ISO 1996 standard. After studying technical and acoustic features of the noise source, a dispersive-absorptive silencer was designed to control noise pollution generated by the cooling tower pump of the thermal station. After analyzing the frequencies of sound pressure level and using available data, a cylindrical silencer (with a diameter of 1.5 m and height of 3 m was designed and manufactured. The internal part of the silencer was filled with different columns of absorbent material covered with punched metal. Therefore, the silencer consisted of (1 acoustic diffuser, (2 acoustic chamber, and (3 acoustic channels. Results Measurements showed that, at a distance of 1 m from the source, sound pressure level reduced from 127 dBA before installing the silencer to 79 dBA after the installation, resulting in a reduction of 48 dBA. Conclusions Using a silencer with absorbent material (glass wool is very effective in reducing the noise generated by the pump.

  10. In-Space Manufacturing Project (prior to FY15: Additive Manufacturing Technology Development)

    Data.gov (United States)

    National Aeronautics and Space Administration — The In-Space Manufacturing (ISM) project is responsible for developing the manufacturing capabilities that will provide on-demand, sustainable operations during NASA...

  11. 32 CFR 507.8 - Articles authorized for manufacture and sale.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 3 2010-07-01 2010-07-01 true Articles authorized for manufacture and sale. 507... CIVIL AUTHORITIES AND PUBLIC RELATIONS MANUFACTURE AND SALE OF DECORATIONS, MEDALS, BADGES, INSIGNIA, COMMERCIAL USE OF HERALDIC DESIGNS AND HERALDIC QUALITY CONTROL PROGRAM Manufacture and Sale of Decorations...

  12. Research for new materials manufacturing using XAFS. Around the non-crystal materials

    International Nuclear Information System (INIS)

    Sakurai, Masaki

    2000-01-01

    In the new materials manufacturing it becomes important to control its structure in nano-scale. The fine structure analysis using XAFS with the proton factory is also useful for the manufacturing. The following two items are reported. 1) The new materials manufacturing from amorphous state is very useful through the control of super cooling state and through the doping of a very small amount of additive elements; Radial distribution analysis using XAFS is important for understanding of the concentration fluctuation in the amorphous. 2) The new materials manufacturing from the cluster as a raw materials; Manufacturing the new materials from the cluster is very useful method through the condensation of the cluster of through the distribution the cluster in the matrix. The magic number clusters such as Me9O6, Me13O8, Me22O12 and Me43O20 (Me=Fe, Co, Ni) are observed they are much stable in comparing with other clusters. These magic number clusters are expected to be useful for the new material manufacturing. For the control of the cluster formation the in-situ analysis using LVCS is important in understanding the cluster formation process. (H. Katsuta)

  13. A novel triple-actuating mechanism of an active air mount for vibration control of precision manufacturing machines: experimental work

    International Nuclear Information System (INIS)

    Kim, Hyung-Tae; Kim, Cheol-Ho; Choi, Seung-Bok; Moon, Seok-Jun; Song, Won-Gil

    2014-01-01

    With the goal of vibration control and isolation in a clean room, we propose a new type of air mount which consists of pneumatic, electromagnetic (EM), and magnetorheological (MR) actuators. The air mount is installed below a semiconductor manufacturing machine to reduce the adverse effects caused by unwanted vibration. The proposed mechanism integrates the forces in a parallel connection of the three actuators. The MR part is designed to operate in an air spring in which the EM part is installed. The control logic is developed with a classical method and a switching mode to avoid operational mismatch among the forces developed. Based on extended microprocessors, a portable, embedded controller is installed to execute both nonlinear logic and digital communication with the peripherals. The pneumatic forces constantly support the heavy weight of an upper structure and maintain the level of the air mount. The MR damper handles the transient response, while the EM controller reduces the resonance response, which is switched mutually with a threshold. Vibration is detected by laser displacement sensors which have submicron resolution. The impact test results of three tons load weight demonstrate practical feasibility by showing that the proposed triple-actuating mechanism can reduce the transient response as well as the resonance in the air mount, resulting in accurate motion of the semiconductor manufacturing machine. (technical note)

  14. Laser 3D micro-manufacturing

    International Nuclear Information System (INIS)

    Piqué, Alberto; Auyeung, Raymond C Y; Kim, Heungsoo; Charipar, Nicholas A; Mathews, Scott A

    2016-01-01

    Laser-based materials processing techniques are gaining widespread use in micro-manufacturing applications. The use of laser microfabrication techniques enables the processing of micro- and nanostructures from a wide range of materials and geometries without the need for masking and etching steps commonly associated with photolithography. This review aims to describe the broad applications space covered by laser-based micro- and nanoprocessing techniques and the benefits offered by the use of lasers in micro-manufacturing processes. Given their non-lithographic nature, these processes are also referred to as laser direct-write and constitute some of the earliest demonstrations of 3D printing or additive manufacturing at the microscale. As this review will show, the use of lasers enables precise control of the various types of processing steps—from subtractive to additive—over a wide range of scales with an extensive materials palette. Overall, laser-based direct-write techniques offer multiple modes of operation including the removal (via ablative processes) and addition (via photopolymerization or printing) of most classes of materials using the same equipment in many cases. The versatility provided by these multi-function, multi-material and multi-scale laser micro-manufacturing processes cannot be matched by photolithography nor with other direct-write microfabrication techniques and offer unique opportunities for current and future 3D micro-manufacturing applications. (topical review)

  15. Application of green concept in mechanical design and manufacture

    Science.gov (United States)

    Liu, Xing ping

    2017-11-01

    With the development of productive forces, the relationship between human and nature is becoming tight increasingly, especially environmental pollution and resource consumption that comes from equipment manufacturing industry mainly. Green development concept is a new concept which can solve the current ecological environment. The philosophical foundation and theoretical basis of green idea are expounded through the study of scientific development and green concept. The difference between the traditional design and the green design is analyzed; the meaning and content of the mechanical design for green concept are discussed. And the evaluation method of green design is discussed too. The significance of green development concept in the mechanical design and manufacturing science is pinpointed clearly. The results show that the implementation of green design under the mechanical design, from the source of pollution control to achieve green manufacturing, is the only way to achieve sustainable development.

  16. A system approach for reducing the environmental impact of manufacturing and sustainability improvement of nano-scale manufacturing

    Science.gov (United States)

    Yuan, Yingchun

    the schematic method is validated by comparing its benchmark results on 104 chemicals with that from the conventional Human Toxicity Potential (HTP) method. This dissertation concludes with discussions on environmental impact assessment of nanotechnologies and sustainability management of nano-particles. As nano-manufacturing is emerging for wide industrial applications, improvement and expansion of the system approach would be valuable for use in the environmental management of nano-manufacturing and in the risk control of nano-particles in the interests of public health and the environment.

  17. Lean Manufacturing Implementation: an Approach to Reduce Production Cost

    Directory of Open Access Journals (Sweden)

    Iraswari

    2012-04-01

    Full Text Available Abstract: Lean Manufacturing Implementation: An Approach To Reduce Production Cost. Opportunities to improve production processes and reduce production cost through the implementation of lean manufacturing in small medium garment manufacturing are presented in this research. This research shows that there is a possibility of decrease in production cost and increase in return on sales. Lean manufacturing implementation can eliminate waste in the production process. This is a set of techniques for identification and elimination of waste gathered from The Ford Production, Statistical Process Control and other techniques. Improvement of quality could be carried out while time and cost of production are being reduced.

  18. Big Data Analytics for Smart Manufacturing: Case Studies in Semiconductor Manufacturing

    Directory of Open Access Journals (Sweden)

    James Moyne

    2017-07-01

    Full Text Available Smart manufacturing (SM is a term generally applied to the improvement in manufacturing operations through integration of systems, linking of physical and cyber capabilities, and taking advantage of information including leveraging the big data evolution. SM adoption has been occurring unevenly across industries, thus there is an opportunity to look to other industries to determine solution and roadmap paths for industries such as biochemistry or biology. The big data evolution affords an opportunity for managing significantly larger amounts of information and acting on it with analytics for improved diagnostics and prognostics. The analytics approaches can be defined in terms of dimensions to understand their requirements and capabilities, and to determine technology gaps. The semiconductor manufacturing industry has been taking advantage of the big data and analytics evolution by improving existing capabilities such as fault detection, and supporting new capabilities such as predictive maintenance. For most of these capabilities: (1 data quality is the most important big data factor in delivering high quality solutions; and (2 incorporating subject matter expertise in analytics is often required for realizing effective on-line manufacturing solutions. In the future, an improved big data environment incorporating smart manufacturing concepts such as digital twin will further enable analytics; however, it is anticipated that the need for incorporating subject matter expertise in solution design will remain.

  19. Computer-controlled ultrasonic equipment for automatic inspection of nuclear reactor components after manufacturing

    International Nuclear Information System (INIS)

    Moeller, P.; Roehrich, H.

    1983-01-01

    After foundation of the working team ''Automated US-Manufacture Testing'' in 1976 the realization of an ultrasonic test facility for nuclear reactor components after manufacturing has been started. During a period of about 5 years, an automated prototype facility has been developed, fabricated and successfully tested. The function of this facility is to replace the manual ultrasonic tests, which are carried out autonomically at different stages of the manufacturing process and to fulfil the test specification under improved economic conditions. This prototype facility has been designed as to be transported to the components to be tested at low expenditure. Hereby the reproduceability of a test is entirely guaranteed. (orig.) [de

  20. Lean manufacturing in Indian context: A survey

    Directory of Open Access Journals (Sweden)

    Rakesh Kumar

    2015-04-01

    Full Text Available This paper is an attempt to examine the implementation of Lean Manufacturing system in the Indian industries. Predominant elements of Lean Manufacturing, benefits gained after its implementation and obstacles observed by Indian Industry have been recognized. The results of this survey support the opinion that Lean Manufacturing had potential to improve the organizational performance of Indian industries. Nevertheless, Indian industries are required to be passionate to transform their manufacturing by adopting Lean manufacturing to gain the full benefits. A large numbers of literature papers are available on the better side of Lean manufacturing approach and its benefits gained by manufacturing organizations after implementation. But the adverse impacts of Lean manufacturing are not discussed to a great extent. Some drawbacks of Lean manufacturing are also highlighted in this paper.

  1. Industrie 4.0: Network Formation on a Distributed Manufacturing Project

    Directory of Open Access Journals (Sweden)

    Luiz Fernando Cardoso dos Santos Durão

    2017-09-01

    Full Text Available The integration of modern internet technology and manufacturing technology, which has been denominated Industrie 4.0, allows for distributed manufacturing using additive manufacturing on a global scale with the integration of machines and processes. However, distributed manufacturing poses many challenges for standardization, quality control and management of information in different manufacturing sites. This article aims to investigate the formation of networks in distributed manufacturing projects, identifying the stake-holders and types of connections throughout the project. The methodological approach used was longitudinal action research for a distributed manufacturing project with a focus on flexible manufacturing. The central plant was located in Germany and the supplier located in Brazil, with a partnership between the Polytechnic School of the University of São Paulo and the Technical University of Darmstadt, Germany. The design and engineering that spawned the product model was developed in Germany, while the additive manufacturing site, the structure, and machinery was developed in Brazil, forming a development and distributed manufacturing network. The results showed how organized the communication and knowledge sharing was among those involved in the distributed manufacturing project, as well as an understanding of what kind of knowledge is shared among those involved.

  2. A modern depleted uranium manufacturing facility

    International Nuclear Information System (INIS)

    Zagula, T.A.

    1995-07-01

    The Specific Manufacturing Capabilities (SMC) Project located at the Idaho National Engineering Laboratory (INEL) and operated by Lockheed Martin Idaho Technologies Co. (LMIT) for the Department of Energy (DOE) manufactures depleted uranium for use in the U.S. Army MIA2 Abrams Heavy Tank Armor Program. Since 1986, SMC has fabricated more than 12 million pounds of depleted uranium (DU) products in a multitude of shapes and sizes with varying metallurgical properties while maintaining security, environmental, health and safety requirements. During initial facility design in the early 1980's, emphasis on employee safety, radiation control and environmental consciousness was gaining momentum throughout the DOE complex. This fact coupled with security and production requirements forced design efforts to focus on incorporating automation, local containment and computerized material accountability at all work stations. The result was a fully automated production facility engineered to manufacture DU armor packages with virtually no human contact while maintaining security, traceability and quality requirements. This hands off approach to handling depleted uranium resulted in minimal radiation exposures and employee injuries. Construction of the manufacturing facility was complete in early 1986 with the first armor package certified in October 1986. Rolling facility construction was completed in 1987 with the first certified plate produced in the fall of 1988. Since 1988 the rolling and manufacturing facilities have delivered more than 2600 armor packages on schedule with 100% final product quality acceptance. During this period there was an annual average of only 2.2 lost time incidents and a single individual maximum radiation exposure of 150 mrem. SMC is an example of designing and operating a facility that meets regulatory requirements with respect to national security, radiation control and personnel safety while achieving production schedules and product quality

  3. Manufacturing Data Uncertainties Propagation Method in Burn-Up Problems

    Directory of Open Access Journals (Sweden)

    Thomas Frosio

    2017-01-01

    Full Text Available A nuclear data-based uncertainty propagation methodology is extended to enable propagation of manufacturing/technological data (TD uncertainties in a burn-up calculation problem, taking into account correlation terms between Boltzmann and Bateman terms. The methodology is applied to reactivity and power distributions in a Material Testing Reactor benchmark. Due to the inherent statistical behavior of manufacturing tolerances, Monte Carlo sampling method is used for determining output perturbations on integral quantities. A global sensitivity analysis (GSA is performed for each manufacturing parameter and allows identifying and ranking the influential parameters whose tolerances need to be better controlled. We show that the overall impact of some TD uncertainties, such as uranium enrichment, or fuel plate thickness, on the reactivity is negligible because the different core areas induce compensating effects on the global quantity. However, local quantities, such as power distributions, are strongly impacted by TD uncertainty propagations. For isotopic concentrations, no clear trends appear on the results.

  4. Development and Implementation of an Automatic Continuous Online Monitoring and Control Platform for Polymerization Reactions to Sharply Boost Energy and Resource Efficiency in Polymer Manufacturing

    Energy Technology Data Exchange (ETDEWEB)

    Reed, Wayne [Tulane Univ., New Orleans, LA (United States); Drenski, Michael [Tulane Univ., New Orleans, LA (United States); Romagnoli, Jose [Tulane Univ., New Orleans, LA (United States)

    2017-10-16

    The project goal was to create an energy saving paradigm shift in how polymers are manufactured in the 21st century. It used Automatic Continuous Online Monitoring of Polymerization reactions (ACOMP) integrated for the first time with automatic active control to create the innovative ‘ACOMP/Control Interface’, or ‘ACOMP/CI’. ACOMP/CI will begin the transformation from old, inefficient processes into highly evolved, energy and resource efficient ones. The ACOMP platform is broadly applicable to many types of reactions and processes throughout the vast polymer industry. The industry provides materials for sectors such as automotive, aerospace, oil recovery, agriculture, paints, resins, adhesives, pharmaceuticals and therapeutic proteins, optics, electronics, lightweight building materials, and many more. The U.S. chemical industry is one of the last major sectors in which the U.S. has top global stature. It consumes 24% of all U.S. manufacturing energy, produces over $800B of product annually, supports 25% of the U.S. GDP and employs over 6 million people. It is also a major source of GHG emissions. Polymers make up approximately 30% of this sector. It is estimated that annually 60 TBtu of energy could be saved and 3 million tons less of GHG emissions produced by optimizing production in the polyolefin manufacturing sector alone. The project scope included first time design and prototyping of an ACOMP/CI, creation of active reaction controllers, and demonstration of control capabilities on ideal, low concentration polymerization reactions. All these elements of the scope were met, including advances and findings not originally anticipated. Extensions to more complex reactions, beyond the reactor capabilities of the current project ACOMP/CI, such as polyolefins and other high pressure/high temperature reactions, are being proposed in Fall 2017 to CESMII, a DoE based NNMI. The initial proposal was for a three year funded project, but this was reduced to a two

  5. Improved Methods for Production Manufacturing Processes in Environmentally Benign Manufacturing

    Directory of Open Access Journals (Sweden)

    Yan-Yan Wang

    2011-09-01

    Full Text Available How to design a production process with low carbon emissions and low environmental impact as well as high manufacturing performance is a key factor in the success of low-carbon production. It is important to address concerns about climate change for the large carbon emission source manufacturing industries because of their high energy consumption and environmental impact during the manufacturing stage of the production life cycle. In this paper, methodology for determining a production process is developed. This methodology integrates process determination from three different levels: new production processing, selected production processing and batch production processing. This approach is taken within a manufacturing enterprise based on prior research. The methodology is aimed at providing decision support for implementing Environmentally Benign Manufacturing (EBM and low-carbon production to improve the environmental performance of the manufacturing industry. At the first level, a decision-making model for new production processes based on the Genetic Simulated Annealing Algorithm (GSAA is presented. The decision-making model considers not only the traditional factors, such as time, quality and cost, but also energy and resource consumption and environmental impact, which are different from the traditional methods. At the second level, a methodology is developed based on an IPO (Input-Process-Output model that integrates assessments of resource consumption and environmental impact in terms of a materials balance principle for batch production processes. At the third level, based on the above two levels, a method for determining production processes that focus on low-carbon production is developed based on case-based reasoning, expert systems and feature technology for designing the process flow of a new component. Through the above three levels, a method for determining the production process to identify, quantify, assess, and optimize the

  6. Quality Control System using Simple Implementation of Seven Tools for Batik Textile Manufacturing

    Science.gov (United States)

    Ragil Suryoputro, Muhammad; Sugarindra, Muchamad; Erfaisalsyah, Hendy

    2017-06-01

    In order to produce better products and mitigate defect in products, every company must implement a quality control system. Company will find means to implement a quality control system that is capable and reliable. One of the methods is using the simple implementation of the seven tools in quality control defects. The case studied in this research was the level of disability xyz grey fabric on a shuttle loom 2 on the Batik manufacturing company. The seven tools that include: flowchart, check sheet, histogram, scatter diagram combined with control charts, Pareto diagrams and fishbone diagrams (causal diagram). Check sheet results obtained types of defects in the grey fabric was woven xyz is warp, double warp, the warp break, double warp, empty warp, warp tenuous, ugly edges, thick warp, and rust. Based on the analysis of control chart indicates that the process is out of control. This can be seen in the graph control where there is still a lot of outlier data. Based on a scatter diagram shows a positive correlation between the percentage of disability and the number of production. Based on Pareto diagram, repair needs priority is for the dominant type of defect is warp (44%) and based on double warp value histogram is also the highest with a value of 23635.11 m. In addition, based on the analysis of the factors causing defect by fishbone diagram double warp or other types of defects originating from the materials, methods, machines, measurements, man and environment. Thus the company can take to minimize the prevention and repair of defects and improve product quality.

  7. Colloidal-based additive manufacturing of bio-inspired composites

    Science.gov (United States)

    Studart, Andre R.

    Composite materials in nature exhibit heterogeneous architectures that are tuned to fulfill the functional demands of the surrounding environment. Examples range from the cellulose-based organic structure of plants to highly mineralized collagen-based skeletal parts like bone and teeth. Because they are often utilized to combine opposing properties such as strength and low-density or stiffness and wear resistance, the heterogeneous architecture of natural materials can potentially address several of the technical limitations of artificial homogeneous composites. However, current man-made manufacturing technologies do not allow for the level of composition and fiber orientation control found in natural heterogeneous systems. In this talk, I will present two additive manufacturing technologies recently developed in our group to build composites with exquisite architectures only rivaled by structures made by living organisms in nature. Since the proposed techniques utilize colloidal suspensions as feedstock, understanding the physics underlying the stability, assembly and rheology of the printing inks is key to predict and control the architecture of manufactured parts. Our results will show that additive manufacturing routes offer a new exciting pathway for the fabrication of biologically-inspired composite materials with unprecedented architectures and functionalities.

  8. 76 FR 72974 - Manufacturer of Controlled Substances Notice of Application

    Science.gov (United States)

    2011-11-28

    ... is notice that on September 15, 2011, Johnson Matthey Pharmaceutical Materials Inc., Pharmaceutical... (9193) II Alfentanil (9737) II Remifentanil (9739) II Sufentanil (9740) II The company plans to utilize... conduct analytical testing in support of the company's primary manufacturing facility in West Deptford...

  9. Manufacturer Usage Description Specification Implementation

    OpenAIRE

    Srinivasan, Kaushik

    2017-01-01

    Manufacturer Usage Description Specification (MUDS) is aframework under RFC development that aims to automate Internet access control rules for IoT devices . These access controls prevent malicious IoT devices from attacking other devices and also protect the IoT devices from being attacked by other devices.We are implementing this framework and trying to improve its security.

  10. Composites Manufacturing Education and Technology Facility Expedites Manufacturing Innovation

    Energy Technology Data Exchange (ETDEWEB)

    2017-01-01

    The Composites Manufacturing Education and Technology facility (CoMET) at the National Wind Technology Center at the National Renewable Energy Laboratory (NREL) paves the way for innovative wind turbine components and accelerated manufacturing. Available for use by industry partners and university researchers, the 10,000-square-foot facility expands NREL's composite manufacturing research capabilities by enabling researchers to design, prototype, and test composite wind turbine blades and other components -- and then manufacture them onsite. Designed to work in conjunction with NREL's design, analysis, and structural testing capabilities, the CoMET facility expedites manufacturing innovation.

  11. A practical discussion of risk management for manufacturing of pharmaceutical products.

    Science.gov (United States)

    Mollah, A Hamid; Baseman, Harold S; Long, Mike; Rathore, Anurag S

    2014-01-01

    Quality risk management (QRM) is now a regulatory expectation, and it makes good business sense. The goal of the risk assessment is to increase process understanding and deliver safe and effective product to the patients. Risk analysis and management is an acceptable and effective way to minimize patient risk and determine the appropriate level of controls in manufacturing. While understanding the elements of QRM is important, knowing how to apply them in the manufacturing environment is essential for effective process performance and control. This article will preview application of QRM in pharmaceutical and biopharmaceutical manufacturing to illustrate how QRM can help the reader achieve that objective. There are several areas of risk that a drug company may encounter in pharmaceutical manufacturing, specifically addressing oral solid and liquid formulations. QRM tools can be used effectively to identify the risks and develop strategy to minimize or control them. Risks are associated throughout the biopharmaceutical manufacturing process-from raw material supply through manufacturing and filling operations to final distribution via a controlled cold chain process. Assessing relevant attributes and risks for biotechnology-derived products is more complicated and challenging for complex pharmaceuticals. This paper discusses key risk factors in biopharmaceutical manufacturing. Successful development and commercialization of pharmaceutical products is all about managing risks. If a company was to take zero risk, most likely the path to commercialization would not be commercially viable. On the other hand, if the risk taken was too much, the product is likely to have a suboptimal safety and efficacy profile and thus is unlikely to be a successful product. This article addresses the topic of quality risk management with the key objective of minimizing patient risk while creating an optimal process and product. Various tools are presented to aid implementation of these

  12. CONWIP versus POLCA: A comparative analysis in a high-mix, low-volume (HMLV) manufacturing environment

    Energy Technology Data Exchange (ETDEWEB)

    Frazee, T.; Standridge, C.

    2016-07-01

    Few studies comparing manufacturing control systems as they relate to high-mix, low-volume applications have been reported. This paper compares two strategies, constant work in process (CONWIP) and Paired-cell Overlapping Loops of Cards with Authorization (POLCA), for controlling work in process (WIP) in such a manufacturing environment. Characteristics of each control method are explained in regards to lead time impact and thus, why one may be advantageous over the other. An industrial system in the Photonics industry is studied. Discrete event simulation is used as the primary tool to compare performance of CONWIP and POLCA controls for the same WIP level with respect to lead time. Model verification and validation are accomplished by comparing historic data to simulation generated data including utilizations. Both deterministic and Poisson distributed order arrivals are considered. For the system considered in this case study, including order arrival patterns, a POLCA control can outperform a CONWIP parameter in terms of average lead time for a given level of WIP. At higher levels of WIP, the performance of POLCA and CONWIP is equivalent. The POLCA control helps limit WIP in specific áreas of the system where the CONWIP control only limits the overall WIP in the system. Thus, POLCA can generate acceptably low lead times at lower levels of WIP for conditions equivalent to the HMLV manufacturing systems studied. The study compliments and extends previous studies of CONWIP and POLCA performance to a HMLV manufacturing environment. It demonstrates the utility of discrete event simulation in that regard. It shows that proper inventory controls in bottleneck áreas of a system can reduce average lead time. (Author)

  13. Semiconductor Manufacturing equipment introduction

    International Nuclear Information System (INIS)

    Im, Jong Sun

    2001-02-01

    This book deals with semiconductor manufacturing equipment. It is comprised of nine chapters, which are manufacturing process of semiconductor device, history of semiconductor manufacturing equipment, kinds and role of semiconductor manufacturing equipment, construction and method of semiconductor manufacturing equipment, introduction of various semiconductor manufacturing equipment, spots of semiconductor manufacturing, technical elements of semiconductor manufacturing equipment, road map of technology of semiconductor manufacturing equipment and semiconductor manufacturing equipment in the 21st century.

  14. Approaches to Quality Risk Management When Using Single-Use Systems in the Manufacture of Biologics.

    Science.gov (United States)

    Ishii-Watabe, Akiko; Hirose, Akihiko; Katori, Noriko; Hashii, Norikata; Arai, Susumu; Awatsu, Hirotoshi; Eiza, Akira; Hara, Yoshiaki; Hattori, Hideshi; Inoue, Tomomi; Isono, Tetsuya; Iwakura, Masahiro; Kajihara, Daisuke; Kasahara, Nobuo; Matsuda, Hiroyuki; Murakami, Sei; Nakagawa, Taishiro; Okumura, Takehiro; Omasa, Takeshi; Takuma, Shinya; Terashima, Iyo; Tsukahara, Masayoshi; Tsutsui, Maiko; Yano, Takahiro; Kawasaki, Nana

    2015-10-01

    Biologics manufacturing technology has made great progress in the last decade. One of the most promising new technologies is the single-use system, which has improved the efficiency of biologics manufacturing processes. To ensure safety of biologics when employing such single-use systems in the manufacturing process, various issues need to be considered including possible extractables/leachables and particles arising from the components used in single-use systems. Japanese pharmaceutical manufacturers, together with single-use suppliers, members of the academia and regulatory authorities have discussed the risks of using single-use systems and established control strategies for the quality assurance of biologics. In this study, we describe approaches for quality risk management when employing single-use systems in the manufacturing of biologics. We consider the potential impact of impurities related to single-use components on drug safety and the potential impact of the single-use system on other critical quality attributes as well as the stable supply of biologics. We also suggest a risk-mitigating strategy combining multiple control methods which includes the selection of appropriate single-use components, their inspections upon receipt and before releasing for use and qualification of single-use systems. Communication between suppliers of single-use systems and the users, as well as change controls in the facilities both of suppliers and users, are also important in risk-mitigating strategies. Implementing these control strategies can mitigate the risks attributed to the use of single-use systems. This study will be useful in promoting the development of biologics as well as in ensuring their safety, quality and stable supply.

  15. Simulation of textile manufacturing processes for planning, scheduling, and quality control purposes

    Science.gov (United States)

    Cropper, A. E.; Wang, Z.

    1995-08-01

    Simulation, as a management information tool, has been applied to engineering manufacture and assembly operations. The application of the principles to textile manufacturing (fiber to fabric) is discussed. The particular problems and solutions in applying the simulation software package to the yarn production processes are discussed with an indication of how the software achieves the production schedule. The system appears to have application in planning, scheduling, and quality assurance. The latter being a result of the traceability possibilities through a process involving mixing and splitting of material.

  16. An Introduction to Intelligent Processing Programs Developed by the Air Force Manufacturing Technology Directorate

    Science.gov (United States)

    Sampson, Paul G.; Sny, Linda C.

    1992-01-01

    The Air Force has numerous on-going manufacturing and integration development programs (machine tools, composites, metals, assembly, and electronics) which are instrumental in improving productivity in the aerospace industry, but more importantly, have identified strategies and technologies required for the integration of advanced processing equipment. An introduction to four current Air Force Manufacturing Technology Directorate (ManTech) manufacturing areas is provided. Research is being carried out in the following areas: (1) machining initiatives for aerospace subcontractors which provide for advanced technology and innovative manufacturing strategies to increase the capabilities of small shops; (2) innovative approaches to advance machine tool products and manufacturing processes; (3) innovative approaches to advance sensors for process control in machine tools; and (4) efforts currently underway to develop, with the support of industry, the Next Generation Workstation/Machine Controller (Low-End Controller Task).

  17. 76 FR 77257 - Manufacturer of Controlled Substances; Notice of Application

    Science.gov (United States)

    2011-12-12

    ...), this is notice that on September 15, 2011, Johnson Matthey Pharma Services, 70 Flagship Drive, North... Schedule Amphetamine (1100) II Methylphenidate (1724) II Hydrocodone (9193) II The company plans to utilize... conduct analytical testing in support of the company's primary manufacturing facility in West Deptford...

  18. 76 FR 25376 - Manufacturer of Controlled Substances; Notice of Application

    Science.gov (United States)

    2011-05-04

    ...), this is notice that on January 5, 2011, Johnson Matthey Pharma Services, 70 Flagship Drive, North... Schedule Amphetamine (1100) II Methylphenidate (1724) II Hydrocodone (9193) II The company plans to utilize... conduct analytical testing in support of the company's primary manufacturing facility in West Deptford...

  19. 75 FR 47029 - Manufacturer of Controlled Substances; Notice of Application

    Science.gov (United States)

    2010-08-04

    ...), this is notice that on January 27, 2009, Johnson Matthey Pharma Services, 70 Flagship Drive, North... Schedule Amphetamine (1100) II Hydrocodone (9193) II Methylphenidate (1724) II The company plans to utilize... conduct analytical testing in support of the company's primary manufacturing facility in West Deptford...

  20. Kine-Mould : Manufacturing technology for curved architectural elements in concrete

    NARCIS (Netherlands)

    Schipper, H.R.; Eigenraam, P.; Grünewald, S.; Soru, M.; Nap, P.; Van Overveld, B.; Vermeulen, J.

    2015-01-01

    The production of architectural elements with complex geometry is challenging for concrete manufacturers. Computer-numerically-controlled (CNC) milled foam moulds have been applied frequently in the last decades, resulting in good aesthetical performance. However, still the costs are high and a

  1. 40 CFR 720.102 - Notice of commencement of manufacture or import.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Notice of commencement of manufacture... (CONTINUED) TOXIC SUBSTANCES CONTROL ACT PREMANUFACTURE NOTIFICATION Commencement of Manufacture or Import § 720.102 Notice of commencement of manufacture or import. (a) Applicability. Any person who commences...

  2. Porosity Measurements and Analysis for Metal Additive Manufacturing Process Control.

    Science.gov (United States)

    Slotwinski, John A; Garboczi, Edward J; Hebenstreit, Keith M

    2014-01-01

    Additive manufacturing techniques can produce complex, high-value metal parts, with potential applications as critical metal components such as those found in aerospace engines and as customized biomedical implants. Material porosity in these parts is undesirable for aerospace parts - since porosity could lead to premature failure - and desirable for some biomedical implants - since surface-breaking pores allows for better integration with biological tissue. Changes in a part's porosity during an additive manufacturing build may also be an indication of an undesired change in the build process. Here, we present efforts to develop an ultrasonic sensor for monitoring changes in the porosity in metal parts during fabrication on a metal powder bed fusion system. The development of well-characterized reference samples, measurements of the porosity of these samples with multiple techniques, and correlation of ultrasonic measurements with the degree of porosity are presented. A proposed sensor design, measurement strategy, and future experimental plans on a metal powder bed fusion system are also presented.

  3. Transforming nanomedicine manufacturing toward Quality by Design and microfluidics.

    Science.gov (United States)

    Colombo, Stefano; Beck-Broichsitter, Moritz; Bøtker, Johan Peter; Malmsten, Martin; Rantanen, Jukka; Bohr, Adam

    2018-04-05

    Nanopharmaceuticals aim at translating the unique features of nano-scale materials into therapeutic products and consequently their development relies critically on the progression in manufacturing technology to allow scalable processes complying with process economy and quality assurance. The relatively high failure rate in translational nanopharmaceutical research and development, with respect to new products on the market, is at least partly due to immature bottom-up manufacturing development and resulting sub-optimal control of quality attributes in nanopharmaceuticals. Recently, quality-oriented manufacturing of pharmaceuticals has undergone an unprecedented change toward process and product development interaction. In this context, Quality by Design (QbD) aims to integrate product and process development resulting in an increased number of product applications to regulatory agencies and stronger proprietary defense strategies of process-based products. Although QbD can be applied to essentially any production approach, microfluidic production offers particular opportunities for QbD-based manufacturing of nanopharmaceuticals. Microfluidics provides unique design flexibility, process control and parameter predictability, and also offers ample opportunities for modular production setups, allowing process feedback for continuously operating production and process control. The present review aims at outlining emerging opportunities in the synergistic implementation of QbD strategies and microfluidic production in contemporary development and manufacturing of nanopharmaceuticals. In doing so, aspects of design and development, but also technology management, are reviewed, as is the strategic role of these tools for aligning nanopharmaceutical innovation, development, and advanced industrialization in the broader pharmaceutical field. Copyright © 2018 Elsevier B.V. All rights reserved.

  4. Cloud Manufacturing Service Paradigm for Group Manufacturing Companies

    Directory of Open Access Journals (Sweden)

    Jingtao Zhou

    2014-07-01

    Full Text Available The continuous refinement of specialization requires that the group manufacturing company must be constantly focused on how to concentrate its core resources in special sphere to form its core competitive advantage. However, the resources in enterprise group are usually distributed in different subsidiary companies, which means they cannot be fully used, constraining the competition and development of the enterprise. Conducted as a response to a need for cloud manufacturing studies, systematic and detailed studies on cloud manufacturing schema for group companies are carried out in this paper. A new hybrid private clouds paradigm is proposed to meet the requirements of aggregation and centralized use of heterogeneous resources and business units distributed in different subsidiary companies. After the introduction of the cloud manufacturing paradigm for enterprise group and its architecture, this paper presents a derivation from the abstraction of paradigm and framework to the application of a practical evaluative working mechanism. In short, the paradigm establishes an effective working mechanism to translate collaborative business process composed by the activities into cloud manufacturing process composed by services so as to create a foundation resulting in mature traditional project monitoring and scheduling technologies being able to be used in cloud manufacturing project management.

  5. Monitoring system for the quality assessment in additive manufacturing

    Energy Technology Data Exchange (ETDEWEB)

    Carl, Volker, E-mail: carl@t-zfp.de [Carl Messtechnik, Thyssenstrasse 183a, 46535 Dinslaken (Germany)

    2015-03-31

    Additive Manufacturing (AM) refers to a process by which a set of digital data -representing a certain complex 3dim design - is used to grow the respective 3dim real structure equal to the corresponding design. For the powder-based EOS manufacturing process a variety of plastic and metal materials can be used. Thereby, AM is in many aspects a very powerful tool as it can help to overcome particular limitations in conventional manufacturing. AM enables more freedom of design, complex, hollow and/or lightweight structures as well as product individualisation and functional integration. As such it is a promising approach with respect to the future design and manufacturing of complex 3dim structures. On the other hand, it certainly calls for new methods and standards in view of quality assessment. In particular, when utilizing AM for the design of complex parts used in aviation and aerospace technologies, appropriate monitoring systems are mandatory. In this respect, recently, sustainable progress has been accomplished by joining the common efforts and concerns of a manufacturer Additive Manufacturing systems and respective materials (EOS), along with those of an operator of such systems (MTU Aero Engines) and experienced application engineers (Carl Metrology), using decent know how in the field of optical and infrared methods regarding non-destructive-examination (NDE). The newly developed technology is best described by a high-resolution layer by layer inspection technique, which allows for a 3D tomography-analysis of the complex part at any time during the manufacturing process. Thereby, inspection costs are kept rather low by using smart image-processing methods as well as CMOS sensors instead of infrared detectors. Moreover, results from conventional physical metallurgy may easily be correlated with the predictive results of the monitoring system which not only allows for improvements of the AM monitoring system, but finally leads to an optimisation of the quality

  6. Influence of Manufacturing Processes on the Performance of Phantom Lungs

    International Nuclear Information System (INIS)

    Traub, Richard J.

    2008-01-01

    Chest counting is an important tool for estimating the radiation dose to individuals who have inhaled radioactive materials. Chest counting systems are calibrated by counting the activity in the lungs of phantoms where the activity in the phantom lungs is known. In the United States a commonly used calibration phantom was developed at the Lawrence Livermore National Laboratory and is referred to as the Livermore Torso Phantom. An important feature of this phantom is that the phantom lungs can be interchanged so that the counting system can be challenged by different combinations of radionuclides and activity. Phantom lungs are made from lung tissue substitutes whose constituents are foaming plastics and various adjuvants selected to make the lung tissue substitute similar to normal healthy lung tissue. Some of the properties of phantom lungs cannot be readily controlled by phantom lung manufacturers. Some, such as density, are a complex function of the manufacturing process, while others, such as elemental composition of the bulk plastic are controlled by the plastics manufacturer without input, or knowledge of the phantom manufacturer. Despite the fact that some of these items cannot be controlled, they can be measured and accounted for. This report describes how manufacturing processes can influence the performance of phantom lungs. It is proposed that a metric that describes the brightness of the lung be employed by the phantom lung manufacturer to determine how well the phantom lung approximates the characteristics of a human lung. For many purposes, the linear attenuation of the lung tissue substitute is an appropriate surrogate for the brightness

  7. 32 CFR 507.9 - Articles not authorized for manufacture or sale.

    Science.gov (United States)

    2010-07-01

    ... 32 National Defense 3 2010-07-01 2010-07-01 true Articles not authorized for manufacture or sale... CIVIL AUTHORITIES AND PUBLIC RELATIONS MANUFACTURE AND SALE OF DECORATIONS, MEDALS, BADGES, INSIGNIA, COMMERCIAL USE OF HERALDIC DESIGNS AND HERALDIC QUALITY CONTROL PROGRAM Manufacture and Sale of Decorations...

  8. Integrated control systems

    International Nuclear Information System (INIS)

    Smith, D.J.

    1991-01-01

    This paper reports that instrument manufacturers must develop standard network interfaces to pull together interrelated systems such as automatic start-up, optimization programs, and online diagnostic systems. In the past individual control system manufacturers have developed their own data highways with proprietary hardware and software designs. In the future, electric utilities will require that future systems, irrespective of manufacturer, should be able to communicate with each other. Until now the manufactures of control systems have not agreed on the standard high-speed data highway system. Currently, the Electric Power Research Institute (EPRI), in conjunction with several electric utilities and equipment manufactures, is working on developing a standard protocol for communicating between various manufacturers' control systems. According to N. Michael of Sargent and Lundy, future control room designs will require that more of the control and display functions be accessible from the control room through CRTs. There will be less emphasis on traditional hard-wired control panels

  9. High energy beam manufacturing technologies

    International Nuclear Information System (INIS)

    Geskin, E.S.; Leu, M.C.

    1989-01-01

    Technological progress continues to enable us to utilize ever widening ranges of physical and chemical conditions for material processing. The increasing cost of energy, raw materials and environmental control make implementation of advanced technologies inevitable. One of the principal avenues in the development of material processing is the increase of the intensity, accuracy, flexibility and stability of energy flow to the processing site. The use of different forms of energy beams is an effective way to meet these sometimes incompatible requirements. The first important technological applications of high energy beams were welding and flame cutting. Subsequently a number of different kinds of beams have been used to solve different problems of part geometry control and improvement of surface characteristics. Properties and applications of different specific beams were subjects of a number of fundamental studies. It is important now to develop a generic theory of beam based manufacturing. The creation of a theory dealing with general principles of beam generation and beam-material interaction will enhance manufacturing science as well as practice. For example, such a theory will provide a format approach for selection and integration of different kinds of beams for a particular application. And obviously, this theory will enable us to integrate the knowledge bases of different manufacturing technologies. The War of the Worlds by H. G. Wells, as well as a number of more technical, although less exciting, publications demonstrate both the feasibility and effectiveness of the generic approach to the description of beam oriented technology. Without any attempt to compete with Wells, we still hope that this volume will contribute to the creation of the theory of beam oriented manufacturing

  10. Telefacturing Based Distributed Manufacturing Environment for Optimal Manufacturing Service by Enhancing the Interoperability in the Hubs

    Directory of Open Access Journals (Sweden)

    V. K. Manupati

    2017-01-01

    Full Text Available Recent happenings are surrounding the manufacturing sector leading to intense progress towards the development of effective distributed collaborative manufacturing environments. This evolving collaborative manufacturing not only focuses on digitalisation of this environment but also necessitates service-dependent manufacturing system that offers an uninterrupted approach to a number of diverse, complicated, dynamic manufacturing operations management systems at a common work place (hub. This research presents a novel telefacturing based distributed manufacturing environment for recommending the manufacturing services based on the user preferences. The first step in this direction is to deploy the most advanced tools and techniques, that is, Ontology-based Protégé 5.0 software for transforming the huge stored knowledge/information into XML schema of Ontology Language (OWL documents and Integration of Process Planning and Scheduling (IPPS for multijobs in a collaborative manufacturing system. Thereafter, we also investigate the possibilities of allocation of skilled workers to the best feasible operations sequence. In this context, a mathematical model is formulated for the considered objectives, that is, minimization of makespan and total training cost of the workers. With an evolutionary algorithm and developed heuristic algorithm, the performance of the proposed manufacturing system has been improved. Finally, to manifest the capability of the proposed approach, an illustrative example from the real-time manufacturing industry is validated for optimal service recommendation.

  11. Micro-manufacturing: design and manufacturing of micro-products

    National Research Council Canada - National Science Library

    Koç, Muammer; Özel, Tuğrul

    2011-01-01

    .... After addressing the fundamentals and non-metallic-based micro-manufacturing processes in the semiconductor industry, it goes on to address specific metallic-based micro-manufacturing processes...

  12. Additive Manufacturing of Shape Memory Alloys

    Science.gov (United States)

    Van Humbeeck, Jan

    2018-04-01

    Selective Laser Melting (SLM) is an additive manufacturing production process, also called 3D printing, in which functional, complex parts are produced by selectively melting patterns in consecutive layers of powder with a laser beam. The pattern the laser beam is following is controlled by software that calculates the pattern by slicing a 3D CAD model of the part to be constructed. Apart from SLM, also other additive manufacturing techniques such as EBM (Electron Beam Melting), FDM (Fused Deposition Modelling), WAAM (Wire Arc Additive Manufacturing), LENS (Laser Engineered Net Shaping such as Laser Cladding) and binder jetting allow to construct complete parts layer upon layer. But since more experience of AM of shape memory alloys is collected by SLM, this paper will overview the potentials, limits and problems of producing NiTi parts by SLM.

  13. Localized melt-scan strategy for site specific control of grain size and primary dendrite arm spacing in electron beam additive manufacturing

    International Nuclear Information System (INIS)

    Raghavan, Narendran; Simunovic, Srdjan; Dehoff, Ryan; Plotkowski, Alex; Turner, John; Kirka, Michael; Babu, Suresh

    2017-01-01

    In addition to design geometry, surface roughness, and solid-state phase transformation, solidification microstructure plays a crucial role in controlling the performance of additively manufactured components. Crystallographic texture, primary dendrite arm spacing (PDAS), and grain size are directly correlated to local solidification conditions. We have developed a new melt-scan strategy for inducing site specific, on-demand control of solidification microstructure. We were able to induce variations in grain size (30 μm–150 μm) and PDAS (4 μm - 10 μm) in Inconel 718 parts produced by the electron beam additive manufacturing system (Arcam ® ). A conventional raster melt-scan resulted in a grain size of about 600 μm. The observed variations in grain size with different melt-scan strategies are rationalized using a numerical thermal and solidification model which accounts for the transient curvature of the melt pool and associated thermal gradients and liquid-solid interface velocities. The refinement in grain size at high cooling rates (>10 4  K/s) is also attributed to the potential heterogeneous nucleation of grains ahead of the epitaxially growing solidification front. The variation in PDAS is rationalized using a coupled numerical-theoretical model as a function of local solidification conditions (thermal gradient and liquid-solid interface velocity) of the melt pool.

  14. Turbine airfoil manufacturing technology

    Energy Technology Data Exchange (ETDEWEB)

    Kortovich, C. [PCC Airfoils, Inc., Beachwood, OH (United States)

    1995-12-31

    The specific goal of this program is to define manufacturing methods that will allow single crystal technology to be applied to complex-cored airfoils components for power generation applications. Tasks addressed include: alloy melt practice to reduce the sulfur content; improvement of casting process; core materials design; and grain orientation control.

  15. Controlled Thermal-Mechanical Processing of Tubes and Pipes for Enhanced Manufacturing and Performance

    Energy Technology Data Exchange (ETDEWEB)

    Kolarik, Robert V.

    2005-11-11

    The Alloy Steel Business of The Timken Company won an award for the controlled thermo-mechanical processing (CTMP) project and assembled a strong international public/private partnership to execute the project. The premise of the CTMP work was to combine Timken's product understanding with its process expertise and knowledge of metallurgical and deformation fundamentals developed during the project to build a predictive process design capability. The CTMP effort succeeded in delivering a pc-based capability in the tube optimization model, with a virtual pilot plant (VPP) feature to represent the desired tube making process to predict the resultant microstructure tailored for the desired application. Additional tasks included a system for direct, online measurement of grain size and demonstration of application of CTMP via robotically enhanced manufacturing.

  16. Additive manufacturing in maxillofacial reconstruction

    Directory of Open Access Journals (Sweden)

    Dincă Luciana Laura

    2017-01-01

    Full Text Available In this paper the benefits of using additive manufacturing technologies in maxillofacial reconstruction are highlighted. Based on a real clinical case, the paper describes the manufacture of an implant prototype replacing the right zygomatic bone and a part of maxilla using additive manufacturing technologies. The face is the most expressive part of the human body that makes us unique. It was shown that the maxillofacial prostheses help to improve the psychological state of patients affected by, because low self esteem feeling appears commonly to this patients with the facial defects. The aim of this paper is to show how using additive manufacturing technologies methods within this research, the producing a surgical model will help surgeon to improve the pre-operative planning. For this we used additive manufacturing technologies such as Stereolitography to achieve the biomodel and FDM-fused deposition modelling to obtain a prototype model because these technologies make it possible to obtain prosthesis according to the physical and mechanical requirements of the region of implantation.

  17. Are computer numerical control (CNC)-manufactured patient-specific metal templates available for posterior thoracic pedicle screw insertion? Feasibility and accuracy evaluation.

    Science.gov (United States)

    Kong, Xiangxue; Tang, Lei; Ye, Qiang; Huang, Wenhua; Li, Jianyi

    2017-11-01

    Accurate and safe posterior thoracic pedicle insertion (PTPI) remains a challenge. Patient-specific drill templates (PDTs) created by rapid prototyping (RP) can assist in posterior thoracic pedicle insertion, but pose biocompatibility risks. The aims of this study were to develop alternative PDTs with computer numerical control (CNC) and assess their feasibility and accuracy in assisting PTPI. Preoperative CT images of 31 cadaveric thoracic vertebras were obtained and then the optimal pedicle screw trajectories were planned. The PDTs with optimal screw trajectories were randomly assigned to be designed and manufactured by CNC or RP in each vertebra. With the guide of the CNC- or RP-manufactured PDTs, the appropriate screws were inserted into the pedicles. Postoperative CT scans were performed to analyze any deviations at entry point and midpoint of the pedicles. The CNC group was found to be significant manufacture-time-shortening, and cost-decreasing, when compared with the RP group (P  0.05). The screw positions were grade 0 in 90.3% and grade 1 in 9.7% of the cases in the CNC group and grade 0 in 93.5% and grade 1 in 6.5% of the cases in the RP group (P = 0.641). CNC-manufactured PDTs are viable for assisting in PTPI with good feasibility and accuracy.

  18. Statistical Analyses and Modeling of the Implementation of Agile Manufacturing Tactics in Industrial Firms

    Directory of Open Access Journals (Sweden)

    Mohammad D. AL-Tahat

    2012-01-01

    Full Text Available This paper provides a review and introduction on agile manufacturing. Tactics of agile manufacturing are mapped into different production areas (eight-construct latent: manufacturing equipment and technology, processes technology and know-how, quality and productivity improvement, production planning and control, shop floor management, product design and development, supplier relationship management, and customer relationship management. The implementation level of agile manufacturing tactics is investigated in each area. A structural equation model is proposed. Hypotheses are formulated. Feedback from 456 firms is collected using five-point-Likert-scale questionnaire. Statistical analysis is carried out using IBM SPSS and AMOS. Multicollinearity, content validity, consistency, construct validity, ANOVA analysis, and relationships between agile components are tested. The results of this study prove that the agile manufacturing tactics have positive effect on the overall agility level. This conclusion can be used by manufacturing firms to manage challenges when trying to be agile.

  19. A livelock control policy for a flexible manufacturing system modeling with a subclass of generalized Petri nets

    Directory of Open Access Journals (Sweden)

    C.Q. Hou

    2014-12-01

    Full Text Available Livelocks, like deadlocks, can result in the serious problems in running process of flexible manufacturing systems (FMSs as well. Current deadlock control policies based on the approaches of siphon detection and control, cannot cope with livelocks in a system of sequential systems with shared resources (S4R, a typical subclass of Petri nets that can model FMSs. On the basis of the mixed integer programming method, this study proposes a livelock control policy (LCP that can not only solve the new smart siphons (NSSs associated with livelocks or deadlocks in an S4R system directly, but also make the solved NSSs max′-controlled by adding the corresponding control places (CPs. As a result, an original S4R system with livelocks or deadlocks can be turned into the live controlled one in which no NSSs can be found. The related theoretical analysis and several examples are given to demonstrate the proposed LCP. Compared with the existing methods in the literature, the proposed one is more general and powerful.

  20. Advances in clinical NK cell studies: Donor selection, manufacturing and quality control

    OpenAIRE

    Koehl, U.; Kalberer, C.; Spanholtz, J.; Lee, D. A.; Miller, J. S.; Cooley, S.; Lowdell, M.; Uharek, L.; Klingemann, H.; Curti, A.; Leung, W.; Alici, E.

    2015-01-01

    ABSTRACT Natural killer (NK) cells are increasingly used in clinical studies in order to treat patients with various malignancies. The following review summarizes platform lectures and 2013?2015 consortium meetings on manufacturing and clinical use of NK cells in Europe and United States. A broad overview of recent pre-clinical and clinical results in NK cell therapies is provided based on unstimulated, cytokine-activated, as well as genetically engineered NK cells using chimeric antigen rece...

  1. Regulatory challenges in manufacturing of pancreatic islets.

    Science.gov (United States)

    Linetsky, E; Ricordi, C

    2008-03-01

    At the present time, transplantation of pancreatic islet cells is considered an experimental therapy for a selected cohort of patients with type 1 diabetes, and is conducted under an Investigational New Drug (IND) application. Encouraging results of the Edmonton Protocol published in the year 2000 sparked a renewed interest in clinical transplantation of allogeneic islets, triggering a large number of IND applications for phase I clinical trials. Promising results reported by a number of centers since then prompted the Food and Drug Administration (FDA) to consider the possibility of licensing allogeneic islets as a therapeutic treatment for patients with type 1 diabetes. However, prior to licensure, issues such as safety, purity, efficacy, and potency of the islet product must be addressed. This is complicated by the intricate nature of pancreatic islets and limited characterization prior to transplantation. In this context, control of the manufacturing process plays a critical role in the definition of the final product. Despite significant progress made in standardization of the donor organ preservation methods, reagents used, and characterization assays performed to qualify an islet cell product, control of the isolation process remains a challenge. Within the scope of the FDA regulations, islet cells meet the definition of a biologic product, somatic cell therapy, and a drug. In addition, AABB standards that address cellular therapy products apply to manufacturing facilities accredited by this organization. Control of the source material, isolation process, and final product are critical issues that must be addressed in the context of FDA and other relevant regulations applicable to islet cell products.

  2. Dropwise additive manufacturing of pharmaceutical products for solvent-based dosage forms.

    Science.gov (United States)

    Hirshfield, Laura; Giridhar, Arun; Taylor, Lynne S; Harris, Michael T; Reklaitis, Gintaras V

    2014-02-01

    In recent years, the US Food and Drug Administration has encouraged pharmaceutical companies to develop more innovative and efficient manufacturing methods with improved online monitoring and control. Mini-manufacturing of medicine is one such method enabling the creation of individualized product forms for each patient. This work presents dropwise additive manufacturing of pharmaceutical products (DAMPP), an automated, controlled mini-manufacturing method that deposits active pharmaceutical ingredients (APIs) directly onto edible substrates using drop-on-demand (DoD) inkjet printing technology. The use of DoD technology allows for precise control over the material properties, drug solid state form, drop size, and drop dynamics and can be beneficial in the creation of high-potency drug forms, combination drugs with multiple APIs or individualized medicine products tailored to a specific patient. In this work, DAMPP was used to create dosage forms from solvent-based formulations consisting of API, polymer, and solvent carrier. The forms were then analyzed to determine the reproducibility of creating an on-target dosage form, the morphology of the API of the final form and the dissolution behavior of the drug over time. DAMPP is found to be a viable alternative to traditional mass-manufacturing methods for solvent-based oral dosage forms. © 2013 Wiley Periodicals, Inc. and the American Pharmacists Association.

  3. CAD And Distributed Manufacturing Solutions for Pellet Boiler Producers

    Directory of Open Access Journals (Sweden)

    Timur Mamut

    2016-12-01

    Full Text Available The paper is summarizing the research activities that had been carried out for defining an appropriate manufacturing concept and the system architecture for a manufacturing plant of pellet boilers. The concept has been validated through the implementation of a solution of computer integrated manufacturing that includes a CAD platform and a CAM facility including laser cutting machines, rolling and welding machines and advanced technologies for assembly, quality control and testing.

  4. 75 FR 1813 - Manufacturer of Controlled Substances; Notice of Registration

    Science.gov (United States)

    2010-01-13

    ... Parkinson's Disease and for manufacture in bulk for investigational new drug (IND) submission and clinical trials. No comments or objections have been received. DEA has considered the factors in 21 U.S.C. 823(a... company's compliance with state and local laws, and a review of the company's background and history...

  5. Improved Large Aperture Collector Manufacturing

    Energy Technology Data Exchange (ETDEWEB)

    O' Rourke, Deven [Abengoa Solar LLC, Lakewood, CO (United States); Farr, Adrian [Abengoa Solar LLC, Lakewood, CO (United States)

    2015-12-01

    The parabolic trough is the most established CSP technology and carries a long history of design experimentation dating back to the 1970’s. This has led to relatively standardized collector architectures, a maturing global supply chain, and a fairly uniform cost reduction strategy. Abengoa has deployed more than 1,500MWe of CSP troughs across several countries and has built and tested full-scale prototypes of many R&D concepts. The latest trough R&D efforts involved efforts to internalize non-CSP industry experience including a preliminary DFMA principles review done with Boothroyd Dewhurst, a construction literature review by the Arizona State University School of Construction Management, and two more focused manufacturing engineering subcontracts done by Ricardo Inc. and the nonprofit Edison Welding Institute. The first two studies highlighted strong opportunities in lowering part count, standardizing components and fasteners, developing modular designs to support prefabrication and automation, and devising simple, error-proof manual assembly methods. These principles have delivered major new cost savings in otherwise “mature” products in analogous industries like automotive, truck trailer manufacture, metal building fabrication, and shipbuilding. For this reason, they were core in the design development of the SpaceTube® collector, and arguably key to its early successes. The latter two studies were applied specifically to the first-generation SpaceTube® design and were important in setting the direction of the present SolarMat project. These studies developed a methodology to analyze the costs of manufacture and assembly, and identify new tooling concepts for more efficient manufacture. Among the main opportunities identified in these studies were the automated mirror arm manufacturing concept and the need for a less infrastructure-intensive assembly line, both of which now form central pillars of the SolarMat project strategy. These new designs will be

  6. Measuring Manufacturing Innovativeness

    DEFF Research Database (Denmark)

    Blichfeldt, Henrik; Knudsen, Mette Præst

    2017-01-01

    Globalization and customization increases the pressure on manufacturing companies, and the ability to provide innovativeness is a potential source of competitive advantage. This paper positions the manufacturing entity in the innovation process, and investigates the relation between innovation vers...... technology and organizational concepts. Based on Danish survey data from the European Manufacturing Survey (EMS-2015) this paper finds that there is a relation between innovative companies, and their level of technology and use of organizational concepts. Technology and organizational concepts act...... as manufacturing levers to support the manufacturing and production system to provide innovativeness. The managerial implication lies in building manufacturing capabilities to support the innovative process, by standardization, optimization and creating stability in combination with automation and advanced...

  7. Design and manufacture of steam generators for replacement

    International Nuclear Information System (INIS)

    Hirano, Hiroshi; Kuri, Syuhei

    1995-01-01

    The basic specification of the steam generators for replacement as heat exchangers (the pressure, temperature, flow rate and thermal output on primary and secondary sides) is set same as that of steam generators before replacement, but the latest design reflecting the operation experience obtained so far and taking the countermeasures for preventing heating tube damage in it is adopted, such as the heating tubes made of TT 690 alloy, the tube support plates with four-lobe shape tube holes made of stainless steel, the stainless steel rest fittings of three in one set and so on. After the heating tube break accident in Mihama No. 2 plant, the quality control was further strengthened. The comparison of the specifications of the steam generators of respective plants before and after the replacement is shown. The main objective of improving steam generators is the heightening of the reliability of heating tubes against intergranular attack and primary water stress corrosion cracking. The improvements of heating tube material, tube support plate material, secondary side heat flow, the shape of tube holes of tube support plates, the method of expanding heating tubes, and vibration-controlling fittings are explained. As to the manufacturing procedure and quality control, the manufacture of raw materials, the build-up welding of tube plates, the manufacture of lower half shell plates, the tube hole making of support plates, the insection of outer cylinder, flow rate distribution plate. Support plates and heating tubes, the sealing welding and expanding of heating tubes, the fixing of rest fittings, the manufacture and fixing of water chamber cover, the manufacture of upper half shell, the fixing of parts inside it, the final joint and inspection are described. (K.I.)

  8. 21 CFR 1310.21 - Sale by Federal departments or agencies of chemicals which could be used to manufacture...

    Science.gov (United States)

    2010-04-01

    ... chemicals which could be used to manufacture controlled substances. 1310.21 Section 1310.21 Food and Drugs... manufacture controlled substances. (a) A Federal department or agency may not sell from the stocks of the... Administration, could be used in the manufacture of a controlled substance, unless the Administrator certifies in...

  9. THTR steam generator licensing experience as seen by the manufacturer

    International Nuclear Information System (INIS)

    Fricker, H.W.

    1981-01-01

    This paper describes the licensing procedures of the manufacture of the 300 MWe THTR steam generator. The following problems are discussed: operating data, design, materials used, manufacture and installation of the generator, and also quality control

  10. State-of-the-art laser additive manufacturing for hot-work tool steels

    OpenAIRE

    Klocke, Fritz; Arntz, Kristian; Teli, Mahesh; Winands, Kai; Wegener, Maximilian; Oliari, Stella

    2017-01-01

    Additive manufacturing (AM) processes are based on the controlled selective deposition of material by which a part is manufactured or remanufactured (repaired), layer by layer. Research in AM is drastically on the increase in the last several years owing to the benefits that AM provides over conventional manufacturing i.e. reduction in material usage, time-to-market reduction, improved functionality, increased ability to customize and near-net shape manufacturing. There has been a number of A...

  11. Changes in quality management for light water reactor fuel manufacturing: A utility's view of driving forces and status

    International Nuclear Information System (INIS)

    Huettmann, A.; Skusa, J.; Ketteler, M.

    2000-01-01

    Quality management in LWR fuel manufacturing for the use in German reactors is based on international guidelines and national/local authority requirements defined in operational licenses. The quality management is twofold and comprises a quality assurance system and the check of manufacturing documents including witnessing of fabrication processes and inspections. Utility and authority appointed technical expert witness manufacturing and take part in inspections performed by the manufacturer where the scope is strictly defined and does not provide possibilities of flexible responses to manufacturing occurrences. For future developments in quality management HEW supports strengthening the ideas of quality planning. Analysis of all factors influencing fuel reliability shall be performed prior to manufacturing. This will increase the efforts in reviewing of drawings and specifications. Included here shall be a review of processes that will be used in manufacturing. The qualification and robustness of processes shall be demonstrated with special qualification programs and analysis of manufacturing statistics. Instead of product/project related inspections the use of all manufacturing data will provide a complete picture of the manufacturing quality. By applying statistical methods it will be possible to identify trends in manufacturing before deviations occur. So the basic driving force to implement statistical process control for the utilities is the wish to get comprehensive information of delivered quality, whereas for manufacturers it might be to increase production yields and thus to lower costs. The introduction and full use of statistical process control requires open information about manufacturing processes and inspection results by the manufacturers. This might include data judged to be economically sensitive. It also requires changes in attitude at the utilities and appointed experts. HEW has started to review and change internal guidelines to allow

  12. Dropwise additive manufacturing of pharmaceutical products for melt-based dosage forms.

    Science.gov (United States)

    Içten, Elçin; Giridhar, Arun; Taylor, Lynne S; Nagy, Zoltan K; Reklaitis, Gintaras V

    2015-05-01

    The US Food and Drug Administration introduced the quality by design approach and process analytical technology guidance to encourage innovation and efficiency in pharmaceutical development, manufacturing, and quality assurance. As part of this renewed emphasis on the improvement of manufacturing, the pharmaceutical industry has begun to develop more efficient production processes with more intensive use of online measurement and sensing, real-time quality control, and process control tools. Here, we present dropwise additive manufacturing of pharmaceutical products (DAMPP) as an alternative to conventional pharmaceutical manufacturing methods. This mini-manufacturing process for the production of pharmaceuticals utilizes drop on demand printing technology for automated and controlled deposition of melt-based formulations onto edible substrates. The advantages of drop-on-demand technology, including reproducible production of small droplets, adjustable drop sizing, high placement accuracy, and flexible use of different formulations, enable production of individualized dosing even for low-dose and high-potency drugs. In this work, DAMPP is used to produce solid oral dosage forms from hot melts of an active pharmaceutical ingredient and a polymer. The dosage forms are analyzed to show the reproducibility of dosing and the dissolution behavior of different formulations. © 2015 Wiley Periodicals, Inc. and the American Pharmacists Association.

  13. 49 CFR 567.5 - Requirements for manufacturers of vehicles manufactured in two or more stages.

    Science.gov (United States)

    2010-10-01

    ... applicable Federal Motor Vehicle Safety Standards, [and Bumper and Theft Prevention Standards, if applicable... 49 Transportation 6 2010-10-01 2010-10-01 false Requirements for manufacturers of vehicles... CERTIFICATION § 567.5 Requirements for manufacturers of vehicles manufactured in two or more stages. (a...

  14. Collaborative Manufacturing for Small-Medium Enterprises

    Science.gov (United States)

    Irianto, D.

    2016-02-01

    Manufacturing systems involve decisions concerning production processes, capacity, planning, and control. In a MTO manufacturing systems, strategic decisions concerning fulfilment of customer requirement, manufacturing cost, and due date of delivery are the most important. In order to accelerate the decision making process, research on decision making structure when receiving order and sequencing activities under limited capacity is required. An effective decision making process is typically required by small-medium components and tools maker as supporting industries to large industries. On one side, metal small-medium enterprises are expected to produce parts, components or tools (i.e. jigs, fixture, mold, and dies) with high precision, low cost, and exact delivery time. On the other side, a metal small- medium enterprise may have weak bargaining position due to aspects such as low production capacity, limited budget for material procurement, and limited high precision machine and equipment. Instead of receiving order exclusively, a small-medium enterprise can collaborate with other small-medium enterprise in order to fulfill requirements high quality, low manufacturing cost, and just in time delivery. Small-medium enterprises can share their best capabilities to form effective supporting industries. Independent body such as community service at university can take a role as a collaboration manager. The Laboratory of Production Systems at Bandung Institute of Technology has implemented shared manufacturing systems for small-medium enterprise collaboration.

  15. 76 FR 8777 - Manufacturer of Controlled Substances; Notice of Registration

    Science.gov (United States)

    2011-02-15

    ... radioactive product used in diagnostic imaging in the diagnosis of Parkinson's Disease and for manufacture in... laws, and a review of the company's background and history. Therefore, pursuant to 21 U.S.C. 823(a... been received. DEA has considered the factors in 21 U.S.C. 823(a) and determined that the registration...

  16. Additive manufacturing of tunable lenses

    Science.gov (United States)

    Schlichting, Katja; Novak, Tobias; Heinrich, Andreas

    2017-02-01

    Individual additive manufacturing of optical systems based on 3D Printing offers varied possibilities in design and usage. In addition to the additive manufacturing procedure, the usage of tunable lenses allows further advantages for intelligent optical systems. Our goal is to bring the advantages of additive manufacturing together with the huge potential of tunable lenses. We produced tunable lenses as a bundle without any further processing steps, like polishing. The lenses were designed and directly printed with a 3D Printer as a package. The design contains the membrane as an optical part as well as the mechanical parts of the lens, like the attachments for the sleeves which contain the oil. The dynamic optical lenses were filled with an oil. The focal length of the lenses changes due to a change of the radius of curvature. This change is caused by changing the pressure in the inside of the lens. In addition to that, we designed lenses with special structures to obtain different areas with an individual optical power. We want to discuss the huge potential of this technology for several applications. Further, an appropriate controlling system is needed. Wéll show the possibilities to control and regulate the optical power of the lenses. The lenses could be used for illumination tasks, and in the future, for individual measurement tasks. The main advantage is the individuality and the possibility to create an individual design which completely fulfills the requirements for any specific application.

  17. 76 FR 62449 - Manufacturer of Controlled Substances; Notice of Application

    Science.gov (United States)

    2011-10-07

    ...), this is notice that on May 4, 2011, Cambrex Charles City, Inc., 1205 11th Street, Charles City, Iowa... Concentrate of Poppy Straw (9670) II Sufentanil (9740) II Fentanyl (9801) II The company will manufacture the...

  18. Virtual manufacturing in reality

    Science.gov (United States)

    Papstel, Jyri; Saks, Alo

    2000-10-01

    SMEs play an important role in manufacturing industry. But from time to time there is a shortage in resources to complete the particular order in time. Number of systems is introduced to produce digital information in order to support product and process development activities. Main problem is lack of opportunity for direct data transition within design system modules when needed temporary extension of design capacity (virtuality) or to implement integrated concurrent product development principles. The planning experience in the field is weakly used as well. The concept of virtual manufacturing is a supporting idea to solve this problem. At the same time a number of practical problems should be solved like information conformity, data transfer, unified technological concepts acceptation etc. In the present paper the proposed ways to solve the practical problems of virtual manufacturing are described. General objective is to introduce the knowledge-based CAPP system as missing module for Virtual Manufacturing in the selected product domain. Surface-centered planning concept based on STEP- based modeling principles, and knowledge-based process planning methodology will be used to gain the objectives. As a result the planning module supplied by design data with direct access, and supporting advising environment is expected. Mould producing SME would be as test basis.

  19. Current manufacturing processes of drug-eluting sutures.

    Science.gov (United States)

    Champeau, Mathilde; Thomassin, Jean-Michel; Tassaing, Thierry; Jérôme, Christine

    2017-11-01

    Drug-eluting sutures represent the next generation of surgical sutures since they fulfill their mechanical functions but also deliver the drug in their vicinity after implantation. These implants are produced by a variety of manufacturing processes. Drug-eluting sutures represent the next generation of surgical sutures since they fulfill their mechanical functions but also deliver the drug in their vicinity after implantation. These implants are produced by a variety of manufacturing processes. Two general approaches can be followed: (i) the ones that add the API into the material during the manufacturing process of the suture and (ii) the ones that load the API to an already manufactured suture. Areas covered: This review provides an overview of the current manufacturing processes for drug-eluting suture production and discusses their benefits and drawbacks depending on the type of drugs. The mechanical properties and the drug delivery profile of drug-eluting sutures are highlighted since these implants must fulfill both criteria. Expert opinion: For limited drug contents, melt extrusion and electrospinning are the emerging processes since the drug is added during the suture manufacture process. Advantageously, the drug release profile can be tuned by controlling the processing parameters specific to each process and the composition of the drug-containing polymer. If high drug content is targeted, the coating or grafting of a drug layer on a pre-manufactured suture allows for preservation of the tensile strength requirements of the suture.

  20. Manufacturing Scheduling Using Colored Petri Nets and Reinforcement Learning

    Directory of Open Access Journals (Sweden)

    Maria Drakaki

    2017-02-01

    Full Text Available Agent-based intelligent manufacturing control systems are capable to efficiently respond and adapt to environmental changes. Manufacturing system adaptation and evolution can be addressed with learning mechanisms that increase the intelligence of agents. In this paper a manufacturing scheduling method is presented based on Timed Colored Petri Nets (CTPNs and reinforcement learning (RL. CTPNs model the manufacturing system and implement the scheduling. In the search for an optimal solution a scheduling agent uses RL and in particular the Q-learning algorithm. A warehouse order-picking scheduling is presented as a case study to illustrate the method. The proposed scheduling method is compared to existing methods. Simulation and state space results are used to evaluate performance and identify system properties.

  1. Acylinder and freeform optical manufacturing

    Science.gov (United States)

    Fess, Edward; Wolfs, Frank; DeFisher, Scott; Ross, James

    2015-10-01

    Aspheric cylinders have the ability to improve optical performance over standard cylindrical surfaces. Over the last several years there has also been development into the application and functionality of utilizing freeform surfaces to improve optical performance. Freeforms have the ability to not only improve image quality over a greater field of view, but can open up the design space of an optical system making it more compact. Freeform geometries, much like aspheric cylinders, may not have an axis of rotation to spin the optic about during manufacturing. This leads to costly fabrication processes and custom metrology set ups, which may inhibit their use. Over the last several years, OptiPro Systems has developed and optimized our eSX grinding, UFF and USF polishing, UltraSurf metrology, and ProSurf software programming technologies to make the processing of these complex geometries much easier and deterministic. In this paper we will discuss the challenges associated with manufacturing complex shapes like aspheric cylinders as well as freeform geometries, and how several technologies working together can overcome them. The technologies focus on metrology feedback to a grinding and polishing machine that is controlled through an iterative computer aided manufacturing software system. We will also present examples of these hard to manufacture shapes with results.

  2. The manufacturing role in fuel performance

    International Nuclear Information System (INIS)

    Barr, A.P.

    1997-01-01

    Manufacturing companies have been involved in the CANDU fuel industry for more than 40 years. Early manufacturing contributions were the development of materials and processes used to fabricate the CANDU fuel bundle. As CANDU reactors were commissioned, the manufacturing contribution has been to produce economical, high quality fuel for the CANDU market. (author)

  3. Cloud manufacturing distributed computing technologies for global and sustainable manufacturing

    CERN Document Server

    Mehnen, Jörn

    2013-01-01

    Global networks, which are the primary pillars of the modern manufacturing industry and supply chains, can only cope with the new challenges, requirements and demands when supported by new computing and Internet-based technologies. Cloud Manufacturing: Distributed Computing Technologies for Global and Sustainable Manufacturing introduces a new paradigm for scalable service-oriented sustainable and globally distributed manufacturing systems.   The eleven chapters in this book provide an updated overview of the latest technological development and applications in relevant research areas.  Following an introduction to the essential features of Cloud Computing, chapters cover a range of methods and applications such as the factors that actually affect adoption of the Cloud Computing technology in manufacturing companies and new geometrical simplification method to stream 3-Dimensional design and manufacturing data via the Internet. This is further supported case studies and real life data for Waste Electrical ...

  4. Acquiring energy savings in manufactured housing

    International Nuclear Information System (INIS)

    Davey, D.

    1993-01-01

    In 1991, the Northwest utilities faced a complex situation. They needed new sources of electrical power to avoid future deficits. A significant block of energy savings was available in the manufactured housing sector in the form of energy savings from increased insulation to new manufactured homes. The manufacturers were interested in saving the electricity in the homes, but would only deal with the utility sector as a whole. Half of the homes targeted were sited in investor-owned utility (IOU) service territories, and half in the public sector made up of utilities that purchased some or all of their electricity from the Bonneville Power Administration. Utilities agreed to acquire energy from manufacturers In the form of thermal efficiency measures specified by the Bonneville Power Administration. The program that resulted from over one year of negotiations was called the Manufactured Housing Acquisition Program, or MAP. Manufacturers, the utilities, State Energy Offices, the Northwest Power Planning Council and Bonneville all worked closely and with tenacity to build the program that went into effect on April 1, 1992, and should save the region between 7 and 9 megawatts, enough energy to supply 11,000 homes in the Northwest

  5. Manufacturing of neutron reflector frame for JMTR

    International Nuclear Information System (INIS)

    Hanawa, Yoshio; Tsuboi, Kazuaki; Takahashi, Kunihiro; Uchida, Munenori; Suzuki, Ken

    2010-03-01

    Beryllium has been used as the neutron reflector in the Japan Materials Testing Reactor (JMTR). A beryllium frame is arranged in the JMTR core and the frame consists of 3 sections (North, East and West). Each section has 7 stories of the beryllium blocks. Each block is connected by the aluminium joints. The capsule or the berylium plug is located in the inside of the beryllium frame. The first criticality achieved in 1968 and the frame has been replaced 6 times and now the 7th frame is being manufactured. The replacement is planned to be done in the spring of 2010. The design has been modified to decrease the swelling camber and the lifetime has been improved. The manufacturing procedure is severely controlled to assure the quality. The chemical composition must be specified to minimize the swelling and radiation. The machining procedure is highly controlled because beryllium is very brittle. And the environmental control is also important, because the beryllium is a toxic material. (author)

  6. Verification of Tolerance Chains in Micro Manufacturing

    DEFF Research Database (Denmark)

    Gasparin, Stefania

    .1 – 200 μm). Finally, an optical component is investigated with the purpose of suggesting a quality control approach for micro-manufacturing process through a control of the product. It is a useful method to adopt when the aim is to detect and quantify inconsistency or incompatibilities during a process...... on dimensional and geometrical metrology. If the measurements uncertainty is large compared to the tolerance interval, a small conformance zone is left for process variation. Therefore particular attention has to be paid to the instrument capabilities in order to reduce the measurement uncertainty. Different...... chain. In this way the process parameters can be adjusted in order to fulfil the requirements of the final micro-product....

  7. Manufacturing mobility in global operations

    NARCIS (Netherlands)

    Steenhuis, H.J.; de Bruijn, E.J.

    2002-01-01

    The globalization trend inevitably affects the organization of manufacturing by enterprises. It offers opportunities to examine manufacturing from a global perspective and consequently to produce where it is most appropriate. However, globalization has also led to an increase in competitive

  8. Manufacturing Renaissance : Return of manufacturing to western countries

    OpenAIRE

    Kianian, Babak; Larsson, Tobias; Tavassoli, Mohammad

    2013-01-01

    This chapter argues that the location of manufacturing is gradually shifting to the west again, exemplifying the ‘manufacturing renaissance’. Such a claim is based on the recent observed trend and the discussion is contextualized within the established theory that has been able to explain the location of manufacturing, that is, the product life cycle (PLC) model. Then the chapter identifies and discusses the four main drivers of this new phenomenon: (i) rising wage levels in emerging economie...

  9. 27 CFR 20.192 - Manufacturing record.

    Science.gov (United States)

    2010-04-01

    ... ingredients used; and (c) Name, trade name or brand name and alcoholic content of each article or intermediate product manufactured, as applicable. (Approved by the Office of Management and Budget under control number...

  10. Subcontracting in electronics : from contract manufacturers to providers of electronic manufacturing services (EMS)

    OpenAIRE

    Liemt van, Gijsbert

    2007-01-01

    Discusses how the top contract manufacturers in the electronics industry try to become providers of electronic manufacturing services by deepening and broadening the rage of services that they offer and by diversifying into markets other than computing and telecommunications.

  11. Manufacturing Capital Lingers in the Stock Market

    Institute of Scientific and Technical Information of China (English)

    吴程涛; 段铸; 张景宇; 张曙光

    2008-01-01

    Pressured by a slowdown in exports, cost increases and dwindling returns to manufacturing investments, China’s manufacturing capital has begun to shift to the real-estate and stock markets. As a matter of fact, the stock market had already felt a shock a couple of years ago when top domestic manufacturers like Midea, Gree, TCL and LMZ started to invest their idle capital in the real-estate and stock markets. Investments of manufacturing capital in both the real estate and stock markets have increased fluid capital and pushed up the value of both markets. Booms in both markets have in turn guaranteed investment returns of manufacturing capital, which further increased the stock market valuations of manufacturing capital. Such a cycle has created interest chains between listed manufacturers, the stock market and the real-estate market. Along with the ups and downs of the stock and real-estate markets, manufacturing capital now faces a dilemma: to escape or to persist? Where should it escape? When can the markets be profitable again? Just like the classic Shakespearean question: to be or not to be, that is the question.

  12. Advanced Manufacturing Systems in Food Processing and Packaging Industry

    International Nuclear Information System (INIS)

    Sani, Mohd Shafie; Aziz, Faieza Abdul

    2013-01-01

    In this paper, several advanced manufacturing systems in food processing and packaging industry are reviewed, including: biodegradable smart packaging and Nano composites, advanced automation control system consists of fieldbus technology, distributed control system and food safety inspection features. The main purpose of current technology in food processing and packaging industry is discussed due to major concern on efficiency of the plant process, productivity, quality, as well as safety. These application were chosen because they are robust, flexible, reconfigurable, preserve the quality of the food, and efficient.

  13. Advanced Manufacturing Systems in Food Processing and Packaging Industry

    Science.gov (United States)

    Shafie Sani, Mohd; Aziz, Faieza Abdul

    2013-06-01

    In this paper, several advanced manufacturing systems in food processing and packaging industry are reviewed, including: biodegradable smart packaging and Nano composites, advanced automation control system consists of fieldbus technology, distributed control system and food safety inspection features. The main purpose of current technology in food processing and packaging industry is discussed due to major concern on efficiency of the plant process, productivity, quality, as well as safety. These application were chosen because they are robust, flexible, reconfigurable, preserve the quality of the food, and efficient.

  14. Foreign Workers, Foreign Multinationals, and Wages after Controlling for Occupation and Sex in Malaysia’s Manufacturing Plants during the mid-1990s

    OpenAIRE

    Eric D., Ramstetter

    2017-01-01

    This paper investigates the effects of foreign worker shares and MNE ownership on wages after controlling for worker sex and occupation in Malaysian manufacturing plants during 1994-1996, an important period during which use of foreign workers began to increase substantially. In a previous paper, I estimated similar wage equations separately for five occupation groups of both sexes in large heterogeneous samples of plants in many industries and more homogeneous samples of plants in seven indu...

  15. 浅析制造企业销售业务内部控制%Analysis on internal control of sales business in manufacturing enterprises

    Institute of Scientific and Technical Information of China (English)

    姚运运

    2016-01-01

    通过分析制造企业销售业务存在的主要问题,提供了制造企业必须加强对客户信用风险、销售业务合同、发货环节、发票开具、销售账款催收等方面的内部控制策略和方法,为制造企业提高销售业务水平,更好地实施对销售业务的内部控制工作提供借鉴和参考。%By analyzing the main problems in the sales business of manufacturing enterprises, the paper provides the internal control strategies and methods for manufacturing enterprises to strengthen credit risk, sales contracts, delivery links, invoicing and collection of receivables, which provides a reference for improving the level of sales operations, and making better implementation of the internal control of sales operations.

  16. Concrete manufacture with un-graded recycled aggregates

    OpenAIRE

    Richardson, Alan; Coventry, Kathryn; Graham, Sue

    2009-01-01

    Purpose – The purpose of this paper is to investigate whether concrete that includes un-graded recycled aggregates can be manufactured to a comparable strength to concrete manufactured from virgin aggregates. \\ud \\ud Design/methodology/approach – A paired comparison test was used to evaluate the difference between concrete made with virgin aggregates (plain control) and concrete including recycled waste. Un-graded construction demolition waste and un-graded ground glass were used as aggregate...

  17. Flow Battery System Design for Manufacturability.

    Energy Technology Data Exchange (ETDEWEB)

    Montoya, Tracy Louise; Meacham, Paul Gregory; Perry, David; Broyles, Robin S.; Hickey, Steven; Hernandez, Jacquelynne

    2014-10-01

    Flow battery energy storage systems can support renewable energy generation and increase energy efficiency. But, presently, the costs of flow battery energy storage systems can be a significant barrier for large-scale market penetration. For cost- effective systems to be produced, it is critical to optimize the selection of materials and components simultaneously with the adherence to requirements and manufacturing processes to allow these batteries and their manufacturers to succeed in the market by reducing costs to consumers. This report analyzes performance, safety, and testing requirements derived from applicable regulations as well as commercial and military standards that would apply to a flow battery energy storage system. System components of a zinc-bromine flow battery energy storage system, including the batteries, inverters, and control and monitoring system, are discussed relative to manufacturing. The issues addressed include costs and component availability and lead times. A service and support model including setup, maintenance and transportation is outlined, along with a description of the safety-related features of the example flow battery energy storage system to promote regulatory and environmental, safety, and health compliance in anticipation of scale manufacturing.

  18. Review of Shape Deviation Modeling for Additive Manufacturing

    OpenAIRE

    Zhu , Zuowei; Keimasi , Safa; ANWER , Nabil; Mathieu , Luc; Qiao , Lihong

    2016-01-01

    International audience; Additive Manufacturing (AM) is becoming a promising technology capable of building complex customized parts with internal geometries and graded material by stacking up thin individual layers. However, a comprehensive geometric model for Additive Manufacturing is not mature yet. Dimensional and form accuracy and surface finish are still a bottleneck for AM regarding quality control. In this paper, an up-to-date review is drawn on methods and approaches that have been de...

  19. Reducing of Manufacturing Lead Time by Implementation of Lean Manufacturing Principles

    Directory of Open Access Journals (Sweden)

    Hussein Salem Ketan

    2015-08-01

    Full Text Available Many organizations today are interesting to implementing lean manufacturing principles that should enable them to eliminating the wastes to reducing a manufacturing lead time. This paper concentrates on increasing the competitive level of the company in globalization markets and improving of the productivity by reducing the manufacturing lead time. This will be by using the main tool of lean manufacturing which is value stream mapping (VSM to identifying all the activities of manufacturing process (value and non-value added activities to reducing elimination of wastes (non-value added activities by converting a manufacturing system to pull instead of push by applying some of pull system strategies as kanban and first on first out lane (FIFO. ARENA software is used to simulate the current and future state. This work is executed in the state company for electrical industries in Baghdad. The obtained results of the application showed that implementation of lean principles helped on reducing of a manufacturing lead time by 33%.

  20. Quality and Safety Assurance of Iron Casts and Manufacturing Processes

    OpenAIRE

    Kukla S.

    2016-01-01

    The scope of this work focuses on the aspects of quality and safety assurance of the iron cast manufacturing processes. Special attention was given to the processes of quality control and after-machining of iron casts manufactured on automatic foundry lines. Due to low level of automation and huge work intensity at this stage of the process, a model area was established which underwent reorganization in accordance with the assumptions of the World Class Manufacturing (WCM). An analysis of wor...

  1. Advanced Manufacturing Technologies (AMT): Additive Manufactured Hot Fire Planning and Testing in GRC Cell 32 Project

    Science.gov (United States)

    Fikes, John C.

    2014-01-01

    The objective of this project is to hot fire test an additively manufactured thrust chamber assembly TCA (injector and thrust chamber). GRC will install the additively manufactured Inconel 625 injector, two additively manufactured (SLM) water cooled Cu-Cr thrust chamber barrels and one additively manufactured (SLM) water cooled Cu-Cr thrust chamber nozzle on the test stand in Cell 32 and perform hot fire testing of the integrated TCA.

  2. Improvements in Operational Readiness by Distributing Manufacturing Capability in the Supply Chain through Additive Manufacturing

    Science.gov (United States)

    2017-12-01

    Second, the report presents the results of laboratory tests designed to evaluate additive manufacturing time of four repair parts. C. RESEARCH...since the production repeatability and reliability of the parts are not well understood (Merritt 2015, 9). The Army’s Additive Manufacturing ...that has a single factory that produces all of their products . This definition is expanded to include a network of manufacturing facilities where each

  3. Microeconomics of yield learning and process control in semiconductor manufacturing

    Science.gov (United States)

    Monahan, Kevin M.

    2003-06-01

    Simple microeconomic models that directly link yield learning to profitability in semiconductor manufacturing have been rare or non-existent. In this work, we review such a model and provide links to inspection capability and cost. Using a small number of input parameters, we explain current yield management practices in 200mm factories. The model is then used to extrapolate requirements for 300mm factories, including the impact of technology transitions to 130nm design rules and below. We show that the dramatic increase in value per wafer at the 300mm transition becomes a driver for increasing metrology and inspection capability and sampling. These analyses correlate well wtih actual factory data and often identify millions of dollars in potential cost savings. We demonstrate this using the example of grating-based overlay metrology for the 65nm node.

  4. Effort levels of the partners in networked manufacturing

    Science.gov (United States)

    Chai, G. R.; Cai, Z.; Su, Y. N.; Zong, S. L.; Zhai, G. Y.; Jia, J. H.

    2017-08-01

    Compared with traditional manufacturing mode, could networked manufacturing improve effort levels of the partners? What factors will affect effort level of the partners? How to encourage the partners to improve their effort levels? To answer these questions, we introduce network effect coefficient to build effort level model of the partners in networked manufacturing. The results show that (1) with the increase of the network effect in networked manufacturing, the actual effort level can go beyond the ideal level of traditional manufacturing. (2) Profit allocation based on marginal contribution rate would help improve effort levels of the partners in networked manufacturing. (3) The partners in networked manufacturing who wishes to have a larger distribution ratio must make a higher effort level, and enterprises with insufficient effort should be terminated in networked manufacturing.

  5. Additive Manufacturing of Fuel Injectors

    Energy Technology Data Exchange (ETDEWEB)

    Sadek Tadros, Dr. Alber Alphonse [Edison Welding Institute, Inc., Columbus, OH (United States); Ritter, Dr. George W. [Edison Welding Institute, Inc., Columbus, OH (United States); Drews, Charles Donald [Edison Welding Institute, Inc., Columbus, OH (United States); Ryan, Daniel [Solar Turbines Inc., San Diego, CA (United States)

    2017-10-24

    Additive manufacturing (AM), also known as 3D-printing, has been shifting from a novelty prototyping paradigm to a legitimate manufacturing tool capable of creating components for highly complex engineered products. An emerging AM technology for producing metal parts is the laser powder bed fusion (L-PBF) process; however, industry manufacturing specifications and component design practices for L-PBF have not yet been established. Solar Turbines Incorporated (Solar), an industrial gas turbine manufacturer, has been evaluating AM technology for development and production applications with the desire to enable accelerated product development cycle times, overall turbine efficiency improvements, and supply chain flexibility relative to conventional manufacturing processes (casting, brazing, welding). Accordingly, Solar teamed with EWI on a joint two-and-a-half-year project with the goal of developing a production L-PBF AM process capable of consistently producing high-nickel alloy material suitable for high temperature gas turbine engine fuel injector components. The project plan tasks were designed to understand the interaction of the process variables and their combined impact on the resultant AM material quality. The composition of the high-nickel alloy powders selected for this program met the conventional cast Hastelloy X compositional limits and were commercially available in different particle size distributions (PSD) from two suppliers. Solar produced all the test articles and both EWI and Solar shared responsibility for analyzing them. The effects of powder metal input stock, laser parameters, heat treatments, and post-finishing methods were evaluated. This process knowledge was then used to generate tensile, fatigue, and creep material properties data curves suitable for component design activities. The key process controls for ensuring consistent material properties were documented in AM powder and process specifications. The basic components of the project

  6. A commercial real-time manufacturing integration platform for the new control system on FTU

    International Nuclear Information System (INIS)

    Panella, M.; Bertocchi, A.; Bozzolan, V.; Buceti, G.; Centioli, C.; Imparato, A.; Mazza, G.; Torelli, C.; Vitale, V.

    1999-01-01

    In 1994 a working group was set up in Frascati to investigate how to build up a new control system for FTU (Frascati tokamak upgrade) considering the evolution in the information technology. Strong emphasis was placed on the use of standard solutions (be they de-facto or de-jure) and commercial platforms where-ever possible. This paper describes our operational experience with the new control system based on the commercial DEC BASEstar family of products. BASEstar is based on client/server computing technologies, providing an environment to collect, process, manage, distribute and integrate real time manufacturing data. UNIX, VMS, PC Win, OS-9 are integrated to handle hosts, PC, VME CPUs. A 4 GL programming language, CIMfast, has been used to handle via automatic procedures the tokamak discharge. X11 standard based mimics are available to display the plants status. A real flexibility of the whole system has been experience and the further use of the this system has been planned for the ITER DTP (divertor test platform). (orig.)

  7. Advanced Manufacturing Technologies

    Science.gov (United States)

    Fikes, John

    2016-01-01

    Advanced Manufacturing Technologies (AMT) is developing and maturing innovative and advanced manufacturing technologies that will enable more capable and lower-cost spacecraft, launch vehicles and infrastructure to enable exploration missions. The technologies will utilize cutting edge materials and emerging capabilities including metallic processes, additive manufacturing, composites, and digital manufacturing. The AMT project supports the National Manufacturing Initiative involving collaboration with other government agencies.

  8. Implementation of the Good Practices of Manufacture of PET Radiopharmaceuticals in INOR

    International Nuclear Information System (INIS)

    Sinconegui Gómez, Belkys; Quesada Cepero, Waldo; González González, Joaquín J.; Calderón Marín, Carlos F.; Varela Corona, Consuelo; Figueroa, Roberto

    2016-01-01

    The growing advance of new technologies in Nuclear Medicine such as positron emission tomography (PET) allows visualizing biological processes in vivo and provides more sensitive results in the diagnosis of oncological processes in asymptomatic stages of the disease and contribute significantly to improve cancer management. It is significant to note that these technologies include radiopharmaceuticals marked with 90 Y and 177 Lu for the therapy of patients already diagnosed by the PET technique that contribute to a significant improvement in the quality of life of patients with cancer. Our country, taking into account the importance of this technology for Health, has developed in INOR a project for the obtaining, dispensing and quality control of PET radiopharmaceuticals marked with 68 Ga for diagnosis and its therapeutic analogues marked with 177 Lu and 90Y in Conditions of Good Manufacturing Practices (GMP). The objective of the present work is to present our experiences in the implementation of the Good Practices of Manufacture of PET Radiopharmaceuticals according to regulation 16-2012 GUIDELINES ON GOOD PRACTICES OF MANUFACTURE OF PHARMACEUTICAL PRODUCTS, issued by the State Control Center for Medicines, Equipment and Devices Doctors (CECMED), a Cuban regulatory body. The implementation of the regulation considers from the preparation of personnel involved in the activity, moving through the facilities and equipment to the validation and quality control. A system for the quality assurance of the production of PET radiopharmaceuticals was implemented in accordance with Annex 5 of Regulation 16-2012 of the CECMED. This is the first experience in Cuba of the implementation of Good Manufacturing Practices of PET Radiopharmaceuticals in Hospital Radiopharmacy. The acquired experiences will be extended to the practices for the preparation of radiopharmaceuticals for the conventional Nuclear Medicine in the INOR.

  9. An Ontology-Based Approach to Enable Knowledge Representation and Reasoning in Worker–Cobot Agile Manufacturing

    Directory of Open Access Journals (Sweden)

    Ahmed R. Sadik

    2017-11-01

    accomplish the cooperative manufacturing concept, a proper approach is required to describe the shared environment between the worker and the cobot. The cooperative manufacturing shared environment includes the cobot, the co-worker, and other production components such as the product itself. Furthermore, the whole cooperative manufacturing system components need to communicate and share their knowledge, to reason and process the shared information, which eventually gives the control solution the capability of obtaining collective manufacturing decisions. Putting into consideration that the control solution should also provide a natural language which is human readable and in the same time can be understood by the machine (i.e., the cobot. Accordingly, a distributed control solution which combines an ontology-based Multi-Agent System (MAS and a Business Rule Management System (BRMS is proposed, in order to solve the mentioned challenges in the cooperative manufacturing, which are: manufacturing knowledge representation, sharing, and reasoning.

  10. A study on manufacturing and quality control technology of DUPIC fuel

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Myung Seung; Park, H. S.; Lee, Y. W. [and others

    1997-09-01

    A series of experiments are performed to verify the manufacturability of DUPIC fuel and its performance by use of HANARO test reactor. Major works performed during this research period are : analysis of manufacturing process of DUPIC fuel, fabrication technology development such as development of disassembly and decladding method of spent PWR fuel, study on the OREOX process using simulated high burnup fuel, weldability of end cap weld, and development of fabrication equipment including the conceptual and detailed design of DUPIC equipment mainly for the powder preparation, pelletization and fuel element fabrication. A study on the material properties of DUPIC fuel and performance analysis method using irradiation of test fuel was also performed. (author). 91 refs., 274 tabs., 254 figs.

  11. A study on manufacturing and quality control technology of DUPIC fuel

    International Nuclear Information System (INIS)

    Yang, Myung Seung; Park, H. S.; Lee, Y. W.

    1997-09-01

    A series of experiments are performed to verify the manufacturability of DUPIC fuel and its performance by use of HANARO test reactor. Major works performed during this research period are : analysis of manufacturing process of DUPIC fuel, fabrication technology development such as development of disassembly and decladding method of spent PWR fuel, study on the OREOX process using simulated high burnup fuel, weldability of end cap weld, and development of fabrication equipment including the conceptual and detailed design of DUPIC equipment mainly for the powder preparation, pelletization and fuel element fabrication. A study on the material properties of DUPIC fuel and performance analysis method using irradiation of test fuel was also performed. (author). 91 refs., 274 tabs., 254 figs

  12. Vision-related problems among the workers engaged in jewellery manufacturing.

    Science.gov (United States)

    Salve, Urmi Ravindra

    2015-01-01

    American Optometric Association defines Computer Vision Syndrome (CVS) as "complex of eye and vision problems related to near work which are experienced during or related to computer use." This happens when visual demand of the tasks exceeds the visual ability of the users. Even though problems were initially attributed to computer-related activities subsequently similar problems are also reported while carrying any near point task. Jewellery manufacturing activities involves precision designs, setting the tiny metals and stones which requires high visual attention and mental concentration and are often near point task. It is therefore expected that the workers engaged in jewellery manufacturing may also experience symptoms like CVS. Keeping the above in mind, this study was taken up (1) To identify the prevalence of symptoms like CVS among the workers of the jewellery manufacturing and compare the same with the workers working at computer workstation and (2) To ascertain whether such symptoms have any permanent vision-related problems. Case control study. The study was carried out in Zaveri Bazaar region and at an IT-enabled organization in Mumbai. The study involved the identification of symptoms of CVS using a questionnaire of Eye Strain Journal, opthalmological check-ups and measurement of Spontaneous Eye Blink rate. The data obtained from the jewellery manufacturing was compared with the data of the subjects engaged in computer work and with the data available in the literature. A comparative inferential statistics was used. Results showed that visual demands of the task carried out in jewellery manufacturing were much higher than that of carried out in computer-related work.

  13. Additive manufacturing of scaffolds with dexamethasone controlled release for enhanced bone regeneration.

    Science.gov (United States)

    Costa, Pedro F; Puga, Ana M; Díaz-Gomez, Luis; Concheiro, Angel; Busch, Dirk H; Alvarez-Lorenzo, Carmen

    2015-12-30

    The adoption of additive manufacturing in tissue engineering and regenerative medicine (TERM) strategies greatly relies on the development of novel 3D printable materials with advanced properties. In this work we have developed a material for bone TERM applications with tunable bioerosion rate and dexamethasone release profile which can be further employed in fused deposition modelling (the most common and accessible 3D printing technology in the market). The developed material consisted of a blend of poly-ϵ-caprolactone (PCL) and poloxamine (Tetronic®) and was processed into a ready-to-use filament form by means of a simplified melt-based methodology, therefore eliminating the utilization of solvents. 3D scaffolds composed of various blend formulations were additively manufactured and analyzed revealing blend ratio-specific degradation rates and dexamethasone release profiles. Furthermore, in vitro culture studies revealed a similar blend ratio-specific trend concerning the osteoinductive activity of the fabricated scaffolds when these were seeded and cultured with human mesenchymal stem cells. The developed material enables to specifically address different regenerative requirements found in various tissue defects. The versatility of such strategy is further increased by the ability of additive manufacturing to accurately fabricate implants matching any given defect geometry. Copyright © 2015 Elsevier B.V. All rights reserved.

  14. Accessibility analysis in manufacturing processes using visibility cones

    Institute of Scientific and Technical Information of China (English)

    尹周平; 丁汉; 熊有伦

    2002-01-01

    Accessibility is a kind of important design feature of products,and accessibility analysis has been acknowledged as a powerful tool for solving computational manufacturing problems arising from different manufacturing processes.After exploring the relations among approachability,accessibility and visibility,a general method for accessibility analysis using visibility cones (VC) is proposed.With the definition of VC of a point,three kinds of visibility of a feature,namely complete visibility cone (CVC),partial visibility cone (PVC) and local visibility cone (LVC),are defined.A novel approach to computing VCs is formulated by identifying C-obstacles in the C-space,for which a general and efficient algorithm is proposed and implemented by making use of visibility culling.Lastly,we discuss briefly how to realize accessibility analysis in numerically controlled (NC) machining planning,coordinate measuring machines (CMMs) inspection planning and assembly sequence planning with the proposed methods.

  15. Study on manufacturing technology of fuel guide tube using HANA alloys

    International Nuclear Information System (INIS)

    Kim, Hyungil; Jung, Yangil; Park, Dongjun; Park, Jeongyong; Kim, Ilhyun; Choi, Byungkwon; Jeong, Yonghwan; Park, Sangyoon

    2013-04-01

    This research was focused on the study for the manufacturing technology of HANA alloys to crease the corrosion resistance of 30% as well as the to improve the strength of 10% when compared to the commercial zirconium alloys. The new manufacturing concept having higher corrosion resistance and strength than commercial alloy performance can be obtained in this research. This result was transferred to the KNF and, that will be commercialized. This research result can be summarized like this; Ο Parameter study to increase formability of HANA alloy tube - Study on alloy element and heat-treatment effect - Study on texture development mechanism - Study on final annealing effect Ο Out-of-pile performance evaluation of HANA alloy tube - Corrosion performance evaluation of HANA alloy manufactured at KNF - Mechanical performance evaluation of HANA alloy manufactured at KNF - Recrystallization behavior evaluation of HANA alloy manufactured at KNF - Texture characterization of HANA alloy manufactured at KNF - Microstructure characterization of HANA alloy manufactured at KNF Ο Manufacturing guideline setup to increase formability of HANA alloy tube - Manufacturing guideline setup to decrease surface defect - Manufacturing guideline setup to increase strength and corrosion resistance - Manufacturing guideline setup to control texture

  16. A review on recent technologies for the manufacture of pulmonary drugs.

    Science.gov (United States)

    Hadiwinoto, Gabriela Daisy; Lip Kwok, Philip Chi; Lakerveld, Richard

    2018-01-01

    This review discusses recent developments in the manufacture of inhalable dry powder formulations. Pulmonary drugs have distinct advantages compared with other drug administration routes. However, requirements of drugs properties complicate the manufacture. Control over crystallization to make particles with the desired properties in a single step is often infeasible, which calls for micronization techniques. Although spray drying produces particles in the desired size range, a stable solid state may not be attainable. Supercritical fluids may be used as a solvent or antisolvent, which significantly reduces solvent waste. Future directions include application areas such as biopharmaceuticals for dry powder inhalers and new processing strategies to improve the control over particle formation such as continuous manufacturing with in-line process analytical technologies.

  17. Mobile Technology Applications for Manufacturing, Reduction of Muda (Waste and the Effect on Manufacturing Economy and Efficiency

    Directory of Open Access Journals (Sweden)

    Angela M Huenerfauth

    2014-10-01

    Full Text Available Mobile devices in the manufacturing setting offer mobility and information whenever and wherever it is needed; these advantages allow for a more efficient workflow and allow the user to make more informed decisions. Due to these advantages, companies are reducing muda (waste by using mobile devices (implementing Lean Manufacturing and therefore saving money. Some of the mobile applications discussed in this paper are the following: Augmented Reality for assembly training, pruefcubing, remotely-monitored shop floors, statistical process control (SPC, and change requests for construction, and the two types of muda (waste reduced by these mobile applications are “unnecessary / excess motion and defects.”

  18. General features of conceptual design for the pilot plant to manufacture fuel rods from mixed oxides

    International Nuclear Information System (INIS)

    Quesada, C.A.; Adelfang, P.; Esteban, A.; Aparicio, G.; Friedenthal, M.; Orlando, O.S.

    1987-01-01

    This paper conceptually describes: 1) the processes in the manufacturing lines; 2) the distribution of quality controls and glove boxes in manufacturing lines; 3) the Control and Radiological Safety Room; 4) the Dressing Room; 5) the requirements of the ventilation system. The plant will be located in the first floor of the Radiochemical Processes Laboratory building, occupying a surface of 600 m 2 . The necessary equipment for the following manufacturing lines will be provided: a) conversion from Pu(NO3)4 to PuO 2 (through Pu(III)oxalate); b) manufacture of homogeneous of mixed oxides of U and Pu; c) manufacture of (U,Pu)O 2 pellets; d) manufacture of fuel rods of mixed uranium and plutonium oxides. (Author)

  19. 77 FR 64462 - Conference on International Trade Issues Facing U.S. Machinery Manufacturing Industries

    Science.gov (United States)

    2012-10-22

    ... manufacturing is one of the largest and most competitive sectors of the American manufacturing economy. The... billion in 2011. The economic impact of machinery manufacturing extends throughout the American economy... service industries. Process control and other automation technologies enable end-users to maximize the...

  20. A PetriNet-Based Approach for Supporting Traceability in Cyber-Physical Manufacturing Systems.

    Science.gov (United States)

    Huang, Jiwei; Zhu, Yeping; Cheng, Bo; Lin, Chuang; Chen, Junliang

    2016-03-17

    With the growing popularity of complex dynamic activities in manufacturing processes, traceability of the entire life of every product has drawn significant attention especially for food, clinical materials, and similar items. This paper studies the traceability issue in cyber-physical manufacturing systems from a theoretical viewpoint. Petri net models are generalized for formulating dynamic manufacturing processes, based on which a detailed approach for enabling traceability analysis is presented. Models as well as algorithms are carefully designed, which can trace back the lifecycle of a possibly contaminated item. A practical prototype system for supporting traceability is designed, and a real-life case study of a quality control system for bee products is presented to validate the effectiveness of the approach.

  1. 75 FR 76756 - Manufacturer of Controlled Substances; Notice of Registration

    Science.gov (United States)

    2010-12-09

    ..., 2010, (75 FR 47029), Johnson Matthey Pharma Services, 70 Flagship Drive, North Andover, Massachusetts... that the registration of Johnson Matthey Pharma Services to manufacture the listed basic classes of... Matthey Pharma Services to ensure that the company's registration is consistent with the public interest...

  2. 76 FR 51402 - Manufacturer of Controlled Substances; Notice of Registration

    Science.gov (United States)

    2011-08-18

    ..., 2011, 76 FR 25376, Johnson Matthey Pharma Services, 70 Flagship Drive, North Andover, Massachusetts... that the registration of Johnson Matthey Pharma Services to manufacture the listed basic classes of... Matthey Pharma Services to ensure that the company's registration is consistent with the public interest...

  3. Raman spectroscopy as a process analytical technology for pharmaceutical manufacturing and bioprocessing.

    Science.gov (United States)

    Esmonde-White, Karen A; Cuellar, Maryann; Uerpmann, Carsten; Lenain, Bruno; Lewis, Ian R

    2017-01-01

    Adoption of Quality by Design (QbD) principles, regulatory support of QbD, process analytical technology (PAT), and continuous manufacturing are major factors effecting new approaches to pharmaceutical manufacturing and bioprocessing. In this review, we highlight new technology developments, data analysis models, and applications of Raman spectroscopy, which have expanded the scope of Raman spectroscopy as a process analytical technology. Emerging technologies such as transmission and enhanced reflection Raman, and new approaches to using available technologies, expand the scope of Raman spectroscopy in pharmaceutical manufacturing, and now Raman spectroscopy is successfully integrated into real-time release testing, continuous manufacturing, and statistical process control. Since the last major review of Raman as a pharmaceutical PAT in 2010, many new Raman applications in bioprocessing have emerged. Exciting reports of in situ Raman spectroscopy in bioprocesses complement a growing scientific field of biological and biomedical Raman spectroscopy. Raman spectroscopy has made a positive impact as a process analytical and control tool for pharmaceutical manufacturing and bioprocessing, with demonstrated scientific and financial benefits throughout a product's lifecycle.

  4. Specifications, quality control, manufacturing, and testing of accelerator magnets

    CERN Document Server

    Einfeld, D

    2010-01-01

    The performance of the magnets plays an important role in the functioning of an accelerator. Most of the magnets are designed at the accelerator laboratory and built by industry. The link between the laboratory and the manufacturer is the contract containing the Technical Specifications of the magnets. For an overview of the contents of the Technical Specifications, the specifications for the magnets of ALBA (bending, quadrupole, and sextupole) are described in this paper. The basic rules of magnet design are reviewed in Appendix A.

  5. Micro Manufacturing

    DEFF Research Database (Denmark)

    Hansen, Hans Nørgaard

    2003-01-01

    Manufacturing deals with systems that include products, processes, materials and production systems. These systems have functional requirements, constraints, design parameters and process variables. They must be decomposed in a systematic manner to achieve the best possible system performance....... If a micro manufacturing system isn’t designed rationally and correctly, it will be high-cost, unreliable, and not robust. For micro products and systems it is a continuously increasing challenge to create the operational basis for an industrial production. As the products through product development...... processes are made applicable to a large number of customers, the pressure in regard to developing production technologies that make it possible to produce the products at a reasonable price and in large numbers is growing. The micro/nano manufacturing programme at the Department of Manufacturing...

  6. 78 FR 48636 - Current Good Manufacturing Practice and Hazard Analysis and Risk-Based Preventive Controls for...

    Science.gov (United States)

    2013-08-09

    ... collection related to the proposed rule, ``Current Good Manufacturing Practice and Hazard Analysis and Risk... period. These two proposals are related to the proposed rule ``Current Good Manufacturing Practice and... final extension of the comment period for the ``Current Good Manufacturing Practice and Hazard Analysis...

  7. AN EXPLORATORY STUDY OF MANUFACTURING STRATEGY OF PACKAGING PRODUCT-MANUFACTURING COMPANIES IN INDIA

    Directory of Open Access Journals (Sweden)

    Pradip P. Patil

    2012-09-01

    Full Text Available This paper presents finding of a survey on manufacturing strategy implementation (MSI adopted by the Indian packaging product manufacturing companies (IPPMC. Though the companies differ in terms of prod uct types (shape, method, content and material of packaging, conversion system, sales volume and sophistication of machinery used, they share common purpose that are used for packaging the product s . With growth in demand for consumer products, packaging f orms basis of differentiating products from competitors. The survey shows emphasis on implementation of manufacturing strategy, key decision areas, identifies competitive priorities, order winners. To get insight, three companies are selected for detailed case studies.

  8. Design for Manufacturing – One-Piece, Fibre-Placed Composite Helicopter Tailboom

    International Nuclear Information System (INIS)

    Marsden, Catharine; Fews, Robert; Oldroyd, Paul; Yousefpour, AH

    2011-01-01

    Recurring cost has become a critical driver in the design of helicopter airframes, and although composite materials have become widely used in aircraft structures, the hand lay-up manufacturing process in many cases prevents these applications from being cost-effective. Automated manufacturing technologies promise not only reduced production costs but also higher quality, repeatable parts. The introduction of existing automated manufacturing techniques and technologies from industries such as the automotive sector into aerospace can be challenging due to the unique product characteristics as well as the stringent certification and quality control requirements of the industry. The aerospace industry is a low-volume, high value production environment where 'hand-made' products are produced by highly experienced and qualified trades-people. Both metallic and composite components are subjected to precise manufacturing control and documentation requirements. The introduction of automated manufacturing technologies must be done in such a way as to respect these often demanding constraints. The introduction of automation to industrialized processes impacts not only the way parts are produced, but also the way they are designed. Successful composite design and manufacturing automation in the aerospace industry requires the engineering designer and analyst to become increasingly involved in the manufacturing of the product, as machine limitations and producibility become increasingly important drivers for design. This paper presents an overview of a development project intended to evaluate the effectiveness and benefits of the automated fibre placement technology through the design, prototype build and testing of a composite tailboom. The discussion centres on the 'design for manufacturing' concept and provides a perspective on the project objectives, material and process selection and trade-offs, geometric and structural considerations, and component assembly and fastening.

  9. Online Scheduling in Manufacturing A Cumulative Delay Approach

    CERN Document Server

    Suwa, Haruhiko

    2013-01-01

    Online scheduling is recognized as the crucial decision-making process of production control at a phase of “being in production" according to the released shop floor schedule. Online scheduling can be also considered as one of key enablers to realize prompt capable-to-promise as well as available-to-promise to customers along with reducing production lead times under recent globalized competitive markets. Online Scheduling in Manufacturing introduces new approaches to online scheduling based on a concept of cumulative delay. The cumulative delay is regarded as consolidated information of uncertainties under a dynamic environment in manufacturing and can be collected constantly without much effort at any points in time during a schedule execution. In this approach, the cumulative delay of the schedule has the important role of a criterion for making a decision whether or not a schedule revision is carried out. The cumulative delay approach to trigger schedule revisions has the following capabilities for the ...

  10. A Novel Robot of Manufacturing Space Solar Cell Arrays

    Directory of Open Access Journals (Sweden)

    Wu Yuexin

    2008-11-01

    Full Text Available This paper presents a novel robot employed to manufacture space solar cell arrays. First of all including the mechanical configuration and control system, the architecture of the robot is described. Then the flow velocity field of adhesive in the dispensing needles is acquired based on hydrodynamics. The accurate section form model of adhesive dispensed on the solar cells is obtained, which is essential for the robot to control the uniformity of dispensing adhesive. Finally the experiment validates the feasibility and reliability of the robot system. The application of robots instead of manual work in manufacturing space solar cell arrays will enhance the development of space industry.

  11. A Novel Robot of Manufacturing Space Solar Cell Arrays

    Directory of Open Access Journals (Sweden)

    Wu Yuexin

    2007-03-01

    Full Text Available This paper presents a novel robot employed to manufacture space solar cell arrays. First of all including the mechanical configuration and control system, the architecture of the robot is described. Then the flow velocity field of adhesive in the dispensing needles is acquired based on hydrodynamics. The accurate section form model of adhesive dispensed on the solar cells is obtained, which is essential for the robot to control the uniformity of dispensing adhesive. Finally the experiment validates the feasibility and reliability of the robot system. The application of robots instead of manual work in manufacturing space solar cell arrays will enhance the development of space industry.

  12. Emerging technologies in arthroplasty: additive manufacturing.

    Science.gov (United States)

    Banerjee, Samik; Kulesha, Gene; Kester, Mark; Mont, Michael A

    2014-06-01

    Additive manufacturing is an industrial technology whereby three-dimensional visual computer models are fabricated into physical components by selectively curing, depositing, or consolidating various materials in consecutive layers. Although initially developed for production of simulated models, the technology has undergone vast improvements and is currently increasingly being used for the production of end-use components in various aerospace, automotive, and biomedical specialties. The ability of this technology to be used for the manufacture of solid-mesh-foam monolithic and coated components of complex geometries previously considered unmanufacturable has attracted the attention of implant manufacturers, bioengineers, and orthopedic surgeons. Currently, there is a paucity of reports describing this fabrication method in the orthopedic literature. Therefore, we aimed to briefly describe this technology, some of the applications in other orthopedic subspecialties, its present use in hip and knee arthroplasty, and concerns with the present form of the technology. As there are few reports of clinical trials presently available, the true benefits of this technology can only be realized when studies evaluating the clinical and radiographic outcomes of cementless implants manufactured with additive manufacturing report durable fixation, less stress shielding, and better implant survivorship. Nevertheless, the authors believe that this technology holds great promise and may potentially change the conventional methods of casting, machining, and tooling for implant manufacturing in the future. Thieme Medical Publishers 333 Seventh Avenue, New York, NY 10001, USA.

  13. Specificity of Good Manufacturing Practice (GMP) for Biomedical Cell Products.

    Science.gov (United States)

    Tulina, M A; Pyatigorskaya, N V

    2018-03-01

    The article describes special aspects of Good Manufacturing Practice (GMP) for biomedical cell products (BMCP) that imply high standards of aseptics throughout the entire productio process, strict requirements to donors and to the procedure of biomaterial isolation, guaranty of tracing BMCP products, defining processing procedures which allow to identify BMCP as minimally manipulated; continuous quality control and automation of the control process at all stages of manufacturing, which will ensure product release simultaneously with completion of technological operations.

  14. An implementation framework for additive manufacturing in supply chains

    Directory of Open Access Journals (Sweden)

    Raed Handal

    2017-12-01

    Full Text Available Additive manufacturing has become one of the most important technologies in the manufacturing field. Full implementation of additive manufacturing will change many well-known management practices in the production sector. However, theoretical development in the field of additive manufacturing with regard to its impact on supply chain management is rare. While additive manufacturing is believed to revolutionize and enhance traditional manufacturing, there is no comprehensive toolset developed in the manufacturing field to assess the impact of additive manufacturing and determine the best production method that suits the applied supply chain strategy. A significant portion of the existing supply chain methods and frameworks were adopted in this study to examine the implementation of additive manufacturing in supply chain management. The aim of this study is to develop a framework to explain when additive manufacturing impacts supply chain management efficiently.

  15. Microfluidic Manufacturing of Polymeric Nanoparticles: Comparing Flow Control of Multiscale Structure in Single-Phase Staggered Herringbone and Two-Phase Reactors.

    Science.gov (United States)

    Xu, Zheqi; Lu, Changhai; Riordon, Jason; Sinton, David; Moffitt, Matthew G

    2016-12-06

    We compare the microfluidic manufacturing of polycaprolactone-block-poly(ethylene oxide) (PCL-b-PEO) nanoparticles (NPs) in a single-phase staggered herringbone (SHB) mixer and in a two-phase gas-liquid segmented mixer. NPs generated from two different copolymer compositions in both reactors and at three different flow rates, along with NPs generated using a conventional bulk method, are compared with respect to morphologies, dimensions, and internal crystallinities. Our work, the first direct comparison between alternate microfluidic NP synthesis methods, shows three key findings: (i) NP morphologies and dimensions produced in the bulk are different from those produced in a microfluidic mixer, whereas NP crystallinities produced in the bulk and in the SHB mixer are similar; (ii) NP morphologies, dimensions, and crystallinities produced in the single-phase SHB and two-phase mixers at the lowest flow rate are similar; and (iii) NP morphologies, dimensions, and crystallinities change with flow rate in the two-phase mixer but not in the single-phase SHB mixer. These findings provide new insights into the relative roles of mixing and shear in the formation and flow-directed processing of polymeric NPs in microfluidics, informing future reactor designs for manufacturing NPs of low polydispersity and controlled multiscale structure and function.

  16. Impact of additive manufacturing on aircraft supply chain performance

    DEFF Research Database (Denmark)

    Ghadge, Abhijeet; Karantoni, Georgia; Chaudhuri, Atanu

    2018-01-01

    Purpose – The purpose of this paper is to assess the impact of additive manufacturing (AM) implementation on aircraft supply chain (SC) networks. Additive and conventional manufacturing spare part inventory control systems are studied and compared, revealing insights into SC performance. Design....... Originality/value – The study provides robust evidence for making critical managerial decisions on SC re-design driven by a new and disruptive technology. Next-generation SC and logistics will replace the current demand for fulfilling material products by AM machines. Keywords Performance measurement......, Simulation, Additive manufacturing, Supply chains, Aerospace industry...

  17. Exploring manufacturing competencies of a two wheeler manufacturing unit

    Science.gov (United States)

    Deep Singh, Chandan; Singh Khamba, Jaimal; Singh, Rajdeep; Singh, Navdeep

    2014-07-01

    The two wheeler industry of India is one of the most dependable industries as every person has at least a two wheeler with him, if not any four wheeler. Earlier there were scooters like Bajaj Chetak, Priya but with evolution of motorcycles like splendor, splendor+, etc. the scooter market started declining but with arrival of gearless scooters like Honda Activa, Scooty Pep, etc. the market place has become increasingly competitive in recent time and industries are facing tough test of improving products and thus market share. The competitiveness among industries is an important issue. Competency development is a vital tool to enhance the competitiveness of industries. Based, on aggregate performance of a firm, it comprehensively explores the varying importance of manufacturing competencies and drives of industrial competitiveness. Hence by, exploring the manufacturing competencies of a two wheeler industry, one can reflect the competitiveness of two wheeler manufacturing industry as a whole. This study presents various factors of manufacturing competencies affecting industrial competitiveness as the significance of these competencies is increasing day by day in two wheeler manufacturing industry.

  18. Exploring manufacturing competencies of a two wheeler manufacturing unit

    International Nuclear Information System (INIS)

    Singh, Chandan Deep; Khamba, Jaimal Singh; Singh, Rajdeep; Singh, Navdeep

    2014-01-01

    The two wheeler industry of India is one of the most dependable industries as every person has at least a two wheeler with him, if not any four wheeler. Earlier there were scooters like Bajaj Chetak, Priya but with evolution of motorcycles like splendor, splendor+, etc. the scooter market started declining but with arrival of gearless scooters like Honda Activa, Scooty Pep, etc. the market place has become increasingly competitive in recent time and industries are facing tough test of improving products and thus market share. The competitiveness among industries is an important issue. Competency development is a vital tool to enhance the competitiveness of industries. Based, on aggregate performance of a firm, it comprehensively explores the varying importance of manufacturing competencies and drives of industrial competitiveness. Hence by, exploring the manufacturing competencies of a two wheeler industry, one can reflect the competitiveness of two wheeler manufacturing industry as a whole. This study presents various factors of manufacturing competencies affecting industrial competitiveness as the significance of these competencies is increasing day by day in two wheeler manufacturing industry

  19. 76 FR 25376 - Manufacturer of Controlled Substances; Notice of Registration

    Science.gov (United States)

    2011-05-04

    ... the public interest at this time. DEA has investigated Johnson Matthey Inc. to ensure that the company... February 3, 2011, 76 FR 6159, Johnson Matthey Inc., Pharmaceuticals Materials, 900 River Road, Conshohocken...) II Hydrocodone (9193) II Morphine (9300) II Thebaine (9333) II The company plans to manufacture the...

  20. Challenges in Additive Manufacturing of Alumina

    OpenAIRE

    Gonzalez, Hugo

    2016-01-01

    Additive manufacturing is seen by many as the holy grail of manufacturing, the ability to produce parts nearly autonomously. Adding material rather than removing it would eliminate the need for expensive resources and machining. The recent expiration of key 3D printing patents has led to many advances in the field and has dramatically lowered the prices of 3D printers, making them accessible to the average individual. The one area where additive manufacturing is still in its infancy is in cer...

  1. Further Cost Reduction of Battery Manufacturing

    Directory of Open Access Journals (Sweden)

    Amir A. Asif

    2017-06-01

    Full Text Available The demand for batteries for energy storage is growing with the rapid increase in photovoltaics (PV and wind energy installation as well as electric vehicle (EV, hybrid electric vehicle (HEV and plug-in hybrid electric vehicle (PHEV. Electrochemical batteries have emerged as the preferred choice for most of the consumer product applications. Cost reduction of batteries will accelerate the growth in all of these sectors. Lithium-ion (Li-ion and solid-state batteries are showing promise through their downward price and upward performance trends. We may achieve further performance improvement and cost reduction for Li-ion and solid-state batteries through reduction of the variation in physical and electrical properties. These properties can be improved and made uniform by considering the electrical model of batteries and adopting novel manufacturing approaches. Using quantum-photo effect, the incorporation of ultra-violet (UV assisted photo-thermal processing can reduce metal surface roughness. Using in-situ measurements, advanced process control (APC can help ensure uniformity among the constituent electrochemical cells. Industrial internet of things (IIoT can streamline the production flow. In this article, we have examined the issue of electrochemical battery manufacturing of Li-ion and solid-state type from cell-level to battery-level process variability, and proposed potential areas where improvements in the manufacturing process can be made. By incorporating these practices in the manufacturing process we expect reduced cost of energy management system, improved reliability and yield gain with the net saving of manufacturing cost being at least 20%.

  2. Value networks in manufacturing sustainability and performance excellence

    CERN Document Server

    Uusitalo, Teuvo

    2017-01-01

    This book highlights innovative solutions together with various techniques and methods that can help support the manufacturing sector to excel in economic, social, and environmental terms in networked business environments. The book also furthers understanding of sustainable manufacturing from the perspective of value creation in manufacturing networks, by capitalizing on the outcomes of the European ‘Sustainable Value Creation in Manufacturing Networks’ project. New dynamics and uncertainties in modern markets call for innovative solutions in the global manufacturing sector. While the manufacturing sector is traditionally driven by technology, it also requires other managerial and organizational solutions in terms of network governance, business models, sustainable solution development for products and services, performance management portals, etc., which can provide major competitive advantages for companies. At the same time, the manufacturing industry is subject to a change process, where business net...

  3. Medição de tempo de atravessamento e inventário em processo em manufatura controlada por ordens de fabricação Lead-time and work-in-process measurement in manufacture controlled by manufacturing orders

    Directory of Open Access Journals (Sweden)

    Miguel Afonso Sellitto

    2008-12-01

    Full Text Available Este artigo trata da aplicação de um método para medição do tempo de atravessamento e do inventário em processo em operações de manufatura controladas por ordens de fabricação. Revisam-se os conceitos de tempo de atravessamento, inventário e filas em manufatura e apresenta-se o método proposto. Coletaram-se as datas de início e término e as quantidades fabricadas em cem ordens de fabricação de um fabricante de máquinas. O método foi aplicado e os resultados permitiram análises sobre a gestão do prazo e da confiabilidade de entrega e da fila na manufatura. Tais critérios podem ser importantes quando a competição no negócio também considera a rapidez e a confiabilidade nas entregas.This paper presents an application of a method for measuring lead-time and work-in-process in manufacturing operations controlled by orders. We review the concepts of lead-time, inventory and queues in manufacturing and present the proposed method. We began by collecting data from one hundred orders, which include release and completion time and delivered quantities. The method was applied and allowed a discussion involving time-to-deliver, dependability of orders and management of queues in shop-floor, which can be important in business competition, when customers expect, from manufacturer, quick response and on-time delivers.

  4. Collaborative Cloud Manufacturing: Design of Business Model Innovations Enabled by Cyberphysical Systems in Distributed Manufacturing Systems

    Directory of Open Access Journals (Sweden)

    Erwin Rauch

    2016-01-01

    Full Text Available Collaborative cloud manufacturing, as a concept of distributed manufacturing, allows different opportunities for changing the logic of generating and capturing value. Cyberphysical systems and the technologies behind them are the enablers for new business models which have the potential to be disruptive. This paper introduces the topics of distributed manufacturing as well as cyberphysical systems. Furthermore, the main business model clusters of distributed manufacturing systems are described, including collaborative cloud manufacturing. The paper aims to provide support for developing business model innovations based on collaborative cloud manufacturing. Therefore, three business model architecture types of a differentiated business logic are discussed, taking into consideration the parameters which have an influence and the design of the business model and its architecture. As a result, new business models can be developed systematically and new ideas can be generated to boost the concept of collaborative cloud manufacturing within all sustainable business models.

  5. Microbiological Control of Flour-Manufacture: Dissemination of Mycotoxins Producing Fungi in Cereal Products

    Directory of Open Access Journals (Sweden)

    T.D. Doolotkeldieva

    2010-01-01

    Full Text Available Wheat grain and its products are widely consumed as fodder and basic daily food stuffs in Kyrgyzstan. Mycobiota is known to produce hazardous effects to a consumer since it produces mycotoxins. Henceforth, mycobiota starting from the field stage to flour, grain and flour samples were selected for mycological analysis from eight sites of flour manufacture: grain stored in storehouses before milling, mechanically cleaned grain, washed grain, grain dried and prepared for mill, roughly-milled flour, first grade flour and high grade flour. The samples were analyzed using classical mycological and immunoassay methods in order to detect mycotoxins producing fungi species. We isolated overall 27 species belonging to 7 genera. Mycotoxins producing species like Aspergillus flavus, Aspergillus ochraceus and Penicillium cyclopium were detected in the stored grains and in mechanically-cleaned grains. The species of Penicillium, Alternaria and Fusarium genera dominated in roughly-milled flour samples, so this site of flour manufacture still has a risk and danger of contamination with mycotoxins producing fungus. Only the final product i.e. the high grade flour lacked any fungal contamination. We recommend to scrutinize flour samples at the last stages of processing, particularly in the mills like B1, C1 and C4.

  6. Manufacturing engineering and technology

    CERN Document Server

    Kalpakjian, Serope; Vijai Sekar, K S

    2014-01-01

    For courses in manufacturing processes at two- or four-year schools. An up-to-date text that provides a solid background in manufacturing processes. Manufacturing Engineering and Technology, SI Edition, 7e, presents a mostly qualitative description of the science, technology, and practice of manufacturing. This includes detailed descriptions of manufacturing processes and the manufacturing enterprise that will help introduce students to important concepts. With a total of 120 examples and case studies, up-to-date and comprehensive coverage of all topics, and superior two-color graphics, this text provides a solid background for manufacturing students and serves as a valuable reference text for professionals. Teaching and Learning Experience To provide a better teaching and learning experience, for both instructors and students, this program will: * Apply Theory and/or Research: An excellent overview of manufacturing conceptswith a balance of relevant fundamentals and real-world practices. * Engage Students: E...

  7. Modelling of human-machine interaction in equipment design of manufacturing cells

    Science.gov (United States)

    Cochran, David S.; Arinez, Jorge F.; Collins, Micah T.; Bi, Zhuming

    2017-08-01

    This paper proposes a systematic approach to model human-machine interactions (HMIs) in supervisory control of machining operations; it characterises the coexistence of machines and humans for an enterprise to balance the goals of automation/productivity and flexibility/agility. In the proposed HMI model, an operator is associated with a set of behavioural roles as a supervisor for multiple, semi-automated manufacturing processes. The model is innovative in the sense that (1) it represents an HMI based on its functions for process control but provides the flexibility for ongoing improvements in the execution of manufacturing processes; (2) it provides a computational tool to define functional requirements for an operator in HMIs. The proposed model can be used to design production systems at different levels of an enterprise architecture, particularly at the machine level in a production system where operators interact with semi-automation to accomplish the goal of 'autonomation' - automation that augments the capabilities of human beings.

  8. PERSPECTIVES FOR FOG COMPUTING IN MANUFACTURING

    Directory of Open Access Journals (Sweden)

    Jakub PIZOŃ

    2016-09-01

    Full Text Available This article discusses ongoing efforts to enable the fog computing vision in manufacturing. As a new paradigm of computing implementation of fog computing faces many challenges that open perspective of new applications within a field of manufacturing. It is expected that fog computing will be one of factors that will accelerate development of in forth industrial revolution. In this article we discuss the perspectives of manufacturing companies surrounded by new solutions of CPS, CPPS and CM in relation to fog computing.

  9. #%Applications of artificial intelligence in intelligent manufacturing: a review

    Institute of Scientific and Technical Information of China (English)

    #

    2017-01-01

    #%Based on research into the applications of artificial intelligence (AI) technology in the manufacturing industry in recent years, we analyze the rapid development of core technologies in the new era of 'Internet plus AI', which is triggering a great change in the models, means, and ecosystems of the manufacturing industry, as well as in the development of AI. We then propose new models, means, and forms of intelligent manufacturing, intelligent manufacturing system architecture, and intelligent man-ufacturing technology system, based on the integration of AI technology with information communications, manufacturing, and related product technology. Moreover, from the perspectives of intelligent manufacturing application technology, industry, and application demonstration, the current development in intelligent manufacturing is discussed. Finally, suggestions for the appli-cation of AI in intelligent manufacturing in China are presented.

  10. Economics of Future Growth in Photovoltaics Manufacturing

    Energy Technology Data Exchange (ETDEWEB)

    Basore, Paul A.; Chung, Donald; Buonassisi, Tonio

    2015-06-14

    The past decade's record of growth in the photovoltaics manufacturing industry indicates that global investment in manufacturing capacity for photovoltaic modules tends to increase in proportion to the size of the industry. The slope of this proportionality determines how fast the industry will grow in the future. Two key parameters determine this slope. One is the annual global investment in manufacturing capacity normalized to the manufacturing capacity for the previous year (capacity-normalized capital investment rate, CapIR, units $/W). The other is how much capital investment is required for each watt of annual manufacturing capacity, normalized to the service life of the assets (capacity-normalized capital demand rate, CapDR, units $/W). If these two parameters remain unchanged from the values they have held for the past few years, global manufacturing capacity will peak in the next few years and then decline. However, it only takes a small improvement in CapIR to ensure future growth in photovoltaics. Any accompanying improvement in CapDR will accelerate that growth.

  11. Fuel manufacturing and utilization

    International Nuclear Information System (INIS)

    2005-01-01

    The efficient utilisation of nuclear fuel requires manufacturing facilities capable of making advanced fuel types, with appropriate quality control. Once made, the use of such fuels requires a proper understanding of their behaviour in the reactor environment, so that safe operation for the design life can be achieved. The International Atomic Energy Agency supports Member States to improve in-pile fuel performance and management of materials; and to develop advanced fuel technologies for ensuring reliability and economic efficiency of the nuclear fuel cycle. It provides assistance to Member States to support fuel-manufacturing capability, including quality assurance techniques, optimization of manufacturing parameters and radiation protection. The IAEA supports the development fuel modelling expertise in Member States, covering both normal operation and postulated and severe accident conditions. It provides information and support for the operation of Nuclear Power Plant to ensure that the environment and water chemistry is appropriate for fuel operation. The IAEA supports fuel failure investigations, including equipment for failed fuel detection and for post-irradiation examination and inspection, as well as fuel repair, it provides information and support research into the basic properties of fuel materials, including UO 2 , MOX and zirconium alloys. It further offers guidance on the relationship with back-end requirement (interim storage, transport, reprocessing, disposal), fuel utilization and management, MOX fuels, alternative fuels and advanced fuel technology

  12. Measure of manufacturing performance in advanced manufacturing systems

    NARCIS (Netherlands)

    Ron, de A.J.

    1995-01-01

    Because of the financial risks as a result of the high investments, decisions concerning investing in advanced manufacturing systems are difficult. The difficulty to decide is gained by the lack of a well-defined measure to support decisions and alarming messages from the industry concerning inverse

  13. A PetriNet-Based Approach for Supporting Traceability in Cyber-Physical Manufacturing Systems

    Directory of Open Access Journals (Sweden)

    Jiwei Huang

    2016-03-01

    Full Text Available With the growing popularity of complex dynamic activities in manufacturing processes, traceability of the entire life of every product has drawn significant attention especially for food, clinical materials, and similar items. This paper studies the traceability issue in cyber-physical manufacturing systems from a theoretical viewpoint. Petri net models are generalized for formulating dynamic manufacturing processes, based on which a detailed approach for enabling traceability analysis is presented. Models as well as algorithms are carefully designed, which can trace back the lifecycle of a possibly contaminated item. A practical prototype system for supporting traceability is designed, and a real-life case study of a quality control system for bee products is presented to validate the effectiveness of the approach.

  14. Mechatronic sensory system for computer integrated manufacturing

    CSIR Research Space (South Africa)

    Kumile, CM

    2007-05-01

    Full Text Available . The framework has been created that defines a formalisation of shop-floor control using sensors previously missing in manufacturing research. The contribution is in the ease and the elegance that the concept provides finite state/ automata activities as well...

  15. Continuous improvement in manufacturing and inspection of fuel; Mejora continua en fabricacion e inspeccion de combustible

    Energy Technology Data Exchange (ETDEWEB)

    Domingon, A.; Ruiz, R.

    2015-07-01

    The manufacturing and inspection process of fuel assemblies in ENUSA is characterized by its robustness acquired over the last thirty years of experience in manufacturing. The reliability of these processes is based on a qualified processes and continuous improvement in the design and upgrading of equipment and optimization of software and manufacturing processes. Additionally, management and quality control systems have been improved in both software and measuring business objectives. this article emphasizes the improvements made over the past five years in management, production and inspection of fuel assemblies. (Author)

  16. Microstructure and corrosion characteristics of HANA 6 alloy with various manufacturing processes

    International Nuclear Information System (INIS)

    Kim, Hyun Gil; Choi, Byung Kwan; Jeong, Yong Hwan

    2008-01-01

    In order to obtain the best manufacturing process for the HANA 6 alloy, the various evaluations such as a corrosion test at 400 .deg. C steam condition, a microstructural analysis by using TEM, and texture analysis by using XRD were performed for the HANA 6 alloy with various manufacturing processes. This alloy was manufactured as sheets by applying 4 types of manufacturing processes which were controlled by a combination of the intermediate annealing temperature and reduction ratio, as well as two types of final annealing conditions which were applied to the HANA 6 alloy from TREX samples. The corrosion resistance of the HANA 6 alloy with various manufacturing processes was increased with a decreasing intermediate annealing temperature and the corrosion resistance of that alloy was decreased by increasing the final annealing temperature after a corrosion test up to 240 days. The precipitate of the HANA 6 alloy mainly consisted of Nb-containing precipitates in all the samples, but the size, distribution and Nb concentration of the precipitates was affected by the applied manufacturing processes. The Nb concentration in the precipitates was increased when the samples were annealed at 570.deg.C during the intermediate annealing processes. So, the corrosion rate of the HANA 6 alloy is affected considerably by a control of the intermediate and final annealing conditions which affect the precipitate characteristics in the matrix. The crystallographic texture of the HANA 6 alloy with various manufacturing processes is similar since the total reduction ratio was the same in all the manufactured sheet samples

  17. Innovative approaches in the manufacture of zirconium alloy components for PHWRs

    International Nuclear Information System (INIS)

    Rao, M.N.; Srivastava, R.K.

    2005-01-01

    Selection of an appropriate route for the fabrication of Zirconium alloy fuel components has a direct bearing on the quality of finished product. Many sophisticated and intricate processes such as vacuum arc melting, extrusion, hot rolling and cold working processes - swaging, drawing and sheet rolling are employed. Many advances were made in eddy current and ultrasonic evaluation to meet the stringent quality control requirement and locate the micro flaws. Emphasis was laid on achieving high recoveries and manufacture the product at minimum cost. Several creative and innovative processes were adopted particularly in the fabrication of end caps and spacers. The spacers were produced through the wire route and subsequently parting them into tiny spacers, which is entirely different from the conventional route of fabricating the sheets followed by blanking and coining. This has improved the material recovery and the lead time has been reduced substantially. The end caps used for the closure of clad tubes have to meet the most stringent quality requirements to avoid micro-flaws. The manufacturing processes adopted have direct influence on the integrity of the finished product. Special defect standards were developed to identify and eliminate micro-flaws and thereby ensure consistent and repetitive quality product. The paper brings out the above innovative approaches made in fabrication and quality control techniques in the manufacture of fuel components for PHWR fuel bundles. (author)

  18. Laser manufacturing: strategies for dealing with the challenges

    Science.gov (United States)

    Barr, John R. M.

    2012-09-01

    Laser manufacturing in Edinburgh was initiated in 1963 by Ferranti (one of the previous names for SELEX Galileo). Since 2003 a modernized range of military lasers has been established. Innovation, both technical and in other aspects of the business, has enabled the design and manufacture of world leading laser designators and countermeasure lasers. Specific examples will be given including: the application of Geometric Algebra to resonator design; novel alignment free optical parametric oscillators; techniques for designing thermally insensitive laser diode pump heads; and methods for contamination control in lasers.

  19. Achieving continuous manufacturing: technologies and approaches for synthesis, workup, and isolation of drug substance. May 20-21, 2014 Continuous Manufacturing Symposium.

    Science.gov (United States)

    Baxendale, Ian R; Braatz, Richard D; Hodnett, Benjamin K; Jensen, Klavs F; Johnson, Martin D; Sharratt, Paul; Sherlock, Jon-Paul; Florence, Alastair J

    2015-03-01

    This whitepaper highlights current challenges and opportunities associated with continuous synthesis, workup, and crystallization of active pharmaceutical ingredients (drug substances). We describe the technologies and requirements at each stage and emphasize the different considerations for developing continuous processes compared with batch. In addition to the specific sequence of operations required to deliver the necessary chemical and physical transformations for continuous drug substance manufacture, consideration is also given to how adoption of continuous technologies may impact different manufacturing stages in development from discovery, process development, through scale-up and into full scale production. The impact of continuous manufacture on drug substance quality and the associated challenges for control and for process safety are also emphasized. In addition to the technology and operational considerations necessary for the adoption of continuous manufacturing (CM), this whitepaper also addresses the cultural, as well as skills and training, challenges that will need to be met by support from organizations in order to accommodate the new work flows. Specific action items for industry leaders are: Develop flow chemistry toolboxes, exploiting the advantages of flow processing and including highly selective chemistries that allow use of simple and effective continuous workup technologies. Availability of modular or plug and play type equipment especially for workup to assist in straightforward deployment in the laboratory. As with learning from other industries, standardization is highly desirable and will require cooperation across industry and academia to develop and implement. Implement and exploit process analytical technologies (PAT) for real-time dynamic control of continuous processes. Develop modeling and simulation techniques to support continuous process development and control. Progress is required in multiphase systems such as

  20. Replacement of milk fat by mixed vegetable oils in manufacturing soft cheese treated by gamma irradiation

    International Nuclear Information System (INIS)

    Afifi, E.A.; Anwar, M.M.

    2007-01-01

    This investigation aimed to study the possibility of substituting milk fat by using blended vegetable oils in manufacturing soft cheese with low salt content, in addition, lo utilize gamma irradiation to prolong the shelf-life of the new manufactured product. Therefore, one hundred (lOOKg) from fresh buffaloes milk containing 5 % milk fal and 3 % salt were divided into tow parts , the first part was used for manufacturing control soft cheese sample (containing milk fat ), while the second part was skimmed, blended with blended vegetable oils and homogenized. The skim homogenized milk containing 5% mixed vegetable oils used for manufacturing soft cheese ( new product filled ). The obtained soft cheese was subjected to 1, 2 and 3 kGy y-irradiation, and stored at refrigerator temperature. During cold storage, the sensory, microbial and chemical properties of control soft cheese and treated one were evaluated. The obtained results indicated that the replacement of milk fat by mixed vegetable oils in the manufacturing soft cheese had no effect on chemical composition and sensory properties except white color and slight oily flavor which have been noticed in treated filled cheese. In addition, irradiation dose of 3 kGy prolonged the shelf-life of treated filled cheese to 42 days compared to 18 days for control sample and scqueiitly, the new product high percentage of iinsaluraled fatly acid and no cholesterol compared with cheese made from natural milk and can be recommended as a healthy food especially for those who need to low or free cholesterol foods

  1. Manufacturing of anode supported SOFCs: Processing parameters and their influence

    DEFF Research Database (Denmark)

    Ramousse, Severine; Menon, Mohan; Brodersen, Karen

    2007-01-01

    The establishment of low cost, highly reliable and reproducible manufacturing processes has been focused for commercialization of SOFC technology. A major challenge in the production chain is the manufacture of anode-supported planar SOFC's single cells in which each layer in a layered structure...... contains a complex microstructure. In order to improve the cell performance as well as reducing the processing costs, it has been found necessary to consider the process chain holistically, because successful manufacture of such a cell and the achievement of optimal final properties depend on each...... of the processing steps and their interdependence. A large database for several thousand anode-supported SOFCs manufactured annually at the Risoe National Laboratory in collaboration with Topsoe Fuel Cell A/S has been constructed. This enables a statistical analysis of the various controlling parameters. Some...

  2. Manufacturing Demonstration Facility: Low Temperature Materials Synthesis

    International Nuclear Information System (INIS)

    Graham, David E.; Moon, Ji-Won; Armstrong, Beth L.; Datskos, Panos G.; Duty, Chad E.; Gresback, Ryan; Ivanov, Ilia N.; Jacobs, Christopher B.; Jellison, Gerald Earle; Jang, Gyoung Gug; Joshi, Pooran C.; Jung, Hyunsung; Meyer, Harry M.; Phelps, Tommy

    2015-01-01

    The Manufacturing Demonstration Facility (MDF) low temperature materials synthesis project was established to demonstrate a scalable and sustainable process to produce nanoparticles (NPs) for advanced manufacturing. Previous methods to chemically synthesize NPs typically required expensive, high-purity inorganic chemical reagents, organic solvents and high temperatures. These processes were typically applied at small laboratory scales at yields sufficient for NP characterization, but insufficient to support roll-to-roll processing efforts or device fabrication. The new NanoFermentation processes described here operated at a low temperature (~60 C) in low-cost, aqueous media using bacteria that produce extracellular NPs with controlled size and elemental stoichiometry. Up-scaling activities successfully demonstrated high NP yields and quality in a 900-L pilot-scale reactor, establishing this NanoFermentation process as a competitive biomanufacturing strategy to produce NPs for advanced manufacturing of power electronics, solid-state lighting and sensors.

  3. Manufacturing Demonstration Facility: Low Temperature Materials Synthesis

    Energy Technology Data Exchange (ETDEWEB)

    Graham, David E. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Moon, Ji-Won [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Armstrong, Beth L. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Datskos, Panos G. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Duty, Chad E. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Gresback, Ryan [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Ivanov, Ilia N. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Jacobs, Christopher B. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Jellison, Gerald Earle [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Jang, Gyoung Gug [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Joshi, Pooran C. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Jung, Hyunsung [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Meyer, III, Harry M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Phelps, Tommy [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

    2015-06-30

    The Manufacturing Demonstration Facility (MDF) low temperature materials synthesis project was established to demonstrate a scalable and sustainable process to produce nanoparticles (NPs) for advanced manufacturing. Previous methods to chemically synthesize NPs typically required expensive, high-purity inorganic chemical reagents, organic solvents and high temperatures. These processes were typically applied at small laboratory scales at yields sufficient for NP characterization, but insufficient to support roll-to-roll processing efforts or device fabrication. The new NanoFermentation processes described here operated at a low temperature (~60 C) in low-cost, aqueous media using bacteria that produce extracellular NPs with controlled size and elemental stoichiometry. Up-scaling activities successfully demonstrated high NP yields and quality in a 900-L pilot-scale reactor, establishing this NanoFermentation process as a competitive biomanufacturing strategy to produce NPs for advanced manufacturing of power electronics, solid-state lighting and sensors.

  4. Improving Project Manufacturing Coordination

    Directory of Open Access Journals (Sweden)

    Korpivaara Ville

    2014-09-01

    Full Text Available The objective of this research is to develop firms’ project manufacturing coordination. The development will be made by centralizing the manufacturing information flows in one system. To be able to centralize information, a deep user need assessment is required. After user needs have been identified, the existing system will be developed to match these needs. The theoretical background is achieved through exploring the literature of project manufacturing, development project success factors and different frameworks and tools for development project execution. The focus of this research is rather in customer need assessment than in system’s technical expertise. To ensure the deep understanding of customer needs this study is executed by action research method. As a result of this research the information system for project manufacturing coordination was developed to respond revealed needs of the stakeholders. The new system improves the quality of the manufacturing information, eliminates waste in manufacturing coordination processes and offers a better visibility to the project manufacturing. Hence it provides a solid base for the further development of project manufacturing.

  5. Developments in fuel manufacturing

    International Nuclear Information System (INIS)

    Williams, T.

    1997-01-01

    BNFL has a long tradition of willingness to embrace technological challenge and a dedication to quality. This paper describes advances in the overall manufacturing philosophy at BNFL's Fuel Business Group and then covers how some new technologies are currently being employed in BNFL Fuel Business Group's flagship oxide complex (OFC), which is currently in its final stages of commissioning. This plant represents a total investment of some Pound 200 million. This paper also describes how these technologies are also being deployed in BNFL's MOX plant now being built at Sellafield and, finally, covers some new processes being developed for advanced fuel manufacture. (author)

  6. PREFACE: Trends in Aerospace Manufacturing 2009 International Conference

    Science.gov (United States)

    Ridgway, Keith; Gault, Rosemary; Allen, Adrian

    2011-12-01

    The aerospace industry is rapidly changing. New aircraft structures are being developed and aero-engines are becoming lighter and more environmentally friendly. In both areas, innovative materials and manufacturing methods are used in an attempt to get maximum performance for minimum cost. At the same time, the structure of the industry has changed and there has been a move from large companies designing, manufacturing components and assembling aircraft to one of large global supply chains headed by large system integrators. All these changes have forced engineers and managers to bring in innovations in design, materials, manufacturing technologies and supply chain management. In September 2009, the Advanced Manufacturing Research Centre (AMRC) at the University of Sheffield held the inaugural Trends in Aerospace Manufacturing conference (TRAM09). This brought together 28 speakers over two days, who presented in sessions on advanced manufacturing trends for the aerospace sector. Areas covered included new materials, including composites, advanced machining, state of the art additive manufacturing techniques, assembly and supply chain issues.

  7. Costs Analysis of Iron Casts Manufacturing

    Directory of Open Access Journals (Sweden)

    S. Kukla

    2012-04-01

    Full Text Available The article presents the issues of costs analysis of iron casts manufacturing using automated foundry lines. Particular attention was paid to departmental costs, conversion costs and costs of in-plant transport. After the Pareto analysis had been carried out, it was possible to set the model area of the process and focus on improving activities related to finishing of a chosen group of casts. In order to eliminate losses, the activities realised in this domain were divided into activities with added value, activities with partially added value and activities without added value. To streamline the production flow, it was proposed to change the location of workstations related to grinding, control and machining of casts. Within the process of constant improvement of manufacturing processes, the aspect of work ergonomics at a workstation was taken into account. As a result of the undertaken actions, some activities without added value were eliminated, efficiency was increased and prime costs of manufacturing casts with regard to finishing treatment were lowered.

  8. Cloud manufacturing: a service-oriented manufacturing paradigm. A review paper

    Directory of Open Access Journals (Sweden)

    Siderska Julia

    2018-03-01

    Full Text Available This paper introduces cloud manufacturing (CMfg as a new manufacturing paradigm that joins the emerging technologies – such as the Internet of Things, cloud computing, and service-oriented technologies – for solving complex problems in manufacturing applications and performing large-scale collaborative manufacturing. Using scientific publications indexed in Scopus database during the period 2012–2017, the concept and fundamentals of CMfg are presented and discussed given the results of the most recent research. While focusing on the current state of the art, the recent research trends within CMfg concept were also identified. The review involved the methods of bibliometric analysis and network analysis. A prototype of CMfg and the existing related work conducted by various researchers are presented, and the map of co-occurrence is introduced to indicate the most commonly occurring issues related to the “cloud manufacturing” term. The VOSviewer software was used for this purpose. Finally, cloud-based manufacturing areas for further research are identified.

  9. Asbestos manufacturing plants in Poland

    Directory of Open Access Journals (Sweden)

    Wilk Ewa

    2014-06-01

    Full Text Available The unique set of physical and chemical properties of asbestos has led to its many industrial applications, such as roof coverings, textiles, rope, cord and yarn, paper, friction and composition materials, household product, acid-resistant filters, packing, insulation, and certain types of lagging, amongst others. In Poland asbestos-containing products were manufactured from raw materials imported mainly from the former Soviet Union, with production launched at the beginning of 20th century. According to Annex 4 to the Act of 19 June 1997 on the prohibition of the use of asbestos-containing products, there were 28 asbestos manufacturing plants in Poland located in 11 provinces throughout the country. The current survey was undertaken to enable asbestos manufacturing plants to be arranged, described and divided in order to contribute to further surveys.

  10. Additive manufacturing in production: challenges and opportunities

    Science.gov (United States)

    Ahuja, Bhrigu; Karg, Michael; Schmidt, Michael

    2015-03-01

    Additive manufacturing, characterized by its inherent layer by layer fabrication methodology has been coined by many as the latest revolution in the manufacturing industry. Due to its diversification of Materials, processes, system technology and applications, Additive Manufacturing has been synonymized with terminology such as Rapid prototyping, 3D printing, free-form fabrication, Additive Layer Manufacturing, etc. A huge media and public interest in the technology has led to an innovative attempt of exploring the technology for applications beyond the scope of the traditional engineering industry. Nevertheless, it is believed that a critical factor for the long-term success of Additive Manufacturing would be its ability to fulfill the requirements defined by the traditional manufacturing industry. A parallel development in market trends and product requirements has also lead to a wider scope of opportunities for Additive Manufacturing. The presented paper discusses some of the key challenges which are critical to ensure that Additive Manufacturing is truly accepted as a mainstream production technology in the industry. These challenges would highlight on various aspects of production such as product requirements, process management, data management, intellectual property, work flow management, quality assurance, resource planning, etc. In Addition, changing market trends such as product life cycle, mass customization, sustainability, environmental impact and localized production will form the foundation for the follow up discussion on the current limitations and the corresponding research opportunities. A discussion on ongoing research to address these challenges would include topics like process monitoring, design complexity, process standardization, multi-material and hybrid fabrication, new material development, etc.

  11. Reconfigurable manufacturing system for agile mass customization manufacturing

    CSIR Research Space (South Africa)

    Xing, B

    2006-07-01

    Full Text Available Manufacturing companies are facing three challenges: low cost production of product, high quality standard and rapid responsiveness to customer requirements. These three goals are equally important for the manufacturing companies who want...

  12. Manufacturing Initiative

    Data.gov (United States)

    National Aeronautics and Space Administration — The Advanced Manufacturing Technologies (AMT) Project supports multiple activities within the Administration's National Manufacturing Initiative. A key component of...

  13. A carbon dioxide stripping model for mammalian cell culture in manufacturing scale bioreactors.

    Science.gov (United States)

    Xing, Zizhuo; Lewis, Amanda M; Borys, Michael C; Li, Zheng Jian

    2017-06-01

    Control of carbon dioxide within the optimum range is important in mammalian bioprocesses at the manufacturing scale in order to ensure robust cell growth, high protein yields, and consistent quality attributes. The majority of bioprocess development work is done in laboratory bioreactors, in which carbon dioxide levels are more easily controlled. Some challenges in carbon dioxide control can present themselves when cell culture processes are scaled up, because carbon dioxide accumulation is a common feature due to longer gas-residence time of mammalian cell culture in large scale bioreactors. A carbon dioxide stripping model can be used to better understand and optimize parameters that are critical to cell culture processes at the manufacturing scale. The prevailing carbon dioxide stripping models in literature depend on mass transfer coefficients and were applicable to cell culture processes with low cell density or at stationary/cell death phase. However, it was reported that gas bubbles are saturated with carbon dioxide before leaving the culture, which makes carbon dioxide stripping no longer depend on a mass transfer coefficient in the new generation cell culture processes characterized by longer exponential growth phase, higher peak viable cell densities, and higher specific production rate. Here, we present a new carbon dioxide stripping model for manufacturing scale bioreactors, which is independent of carbon dioxide mass transfer coefficient, but takes into account the gas-residence time and gas CO 2 saturation time. The model was verified by CHO cell culture processes with different peak viable cell densities (7 to 12 × 10 6  cells mL -1 ) for two products in 5,000-L and 25,000-L bioreactors. The model was also applied to a next generation cell culture process to optimize cell culture conditions and reduce carbon dioxide levels at manufacturing scale. The model provides a useful tool to understand and better control cell culture carbon dioxide

  14. Eucalyptus grandis AND Eucalyptus dunnii USE FOR WOOD-CEMENT PANELS MANUFACTURING

    Directory of Open Access Journals (Sweden)

    Setsuo Iwakiri

    2008-03-01

    Full Text Available This research evaluated the potential use of Eucalyptus grandis and Eucalyptus dunnii wood for wood-cement panelsmanufacturing. The boards were manufactured at the density of 1,20 g/cm³, using portland cement as mineral bonding and woodfurnish without treatment, treated in cold water and hot water. The wood furnish of Pinus taeda was used as control. The resultsindicated that it is not necessary to treat E. grandis and E. dunni wood for wood-cement board manufacturing. In relation to woodspecies, the board manufactured with E. dunnii showed lower values of mechanical properties. However, boards manufactured of E.grandis wood showed satisfactory results in comparison to boards of P. taeda and the referenced values of BISON process and otherproducts cited in the pertnent literature, indicating the high potential for wood-cement board manufacture of this tree species.

  15. In-Space Manufacturing Baseline Property Development

    Science.gov (United States)

    Stockman, Tom; Schneider, Judith; Prater, Tracie; Bean, Quincy; Werkheiser, Nicki

    2016-01-01

    The In-Space Manufacturing (ISM) project at NASA Marshall Space Flight Center currently operates a 3D FDM (fused deposition modeling) printer onboard the International Space Station. In order to enable utilization of this capability by designer, the project needs to establish characteristic material properties for materials produced using the process. This is difficult for additive manufacturing since standards and specifications do not yet exist for these technologies. Due to availability of crew time, there are limitations to the sample size which in turn limits the application of the traditional design allowables approaches to develop a materials property database for designers. In this study, various approaches to development of material databases were evaluated for use by designers of space systems who wish to leverage in-space manufacturing capabilities. This study focuses on alternative statistical techniques for baseline property development to support in-space manufacturing.

  16. Additive manufacturing.

    Science.gov (United States)

    Mumith, A; Thomas, M; Shah, Z; Coathup, M; Blunn, G

    2018-04-01

    Increasing innovation in rapid prototyping (RP) and additive manufacturing (AM), also known as 3D printing, is bringing about major changes in translational surgical research. This review describes the current position in the use of additive manufacturing in orthopaedic surgery. Cite this article: Bone Joint J 2018;100-B:455-60.

  17. Modular industrial robots as the tool of process automation in robotized manufacturing cells

    Science.gov (United States)

    Gwiazda, A.; Banas, W.; Sekala, A.; Foit, K.; Hryniewicz, P.; Kost, G.

    2015-11-01

    Recently the number of designed modular machine was increased. The term modular machine is used to denote different types of machinery, equipment and production lines, which are created using modular elements. Modular could be both mechanic elements, and drives, as well as control systems. This method of machine design is more and more popular because it allows obtaining flexible and relatively cheap solutions. So it is worth to develop the concept of modularity in next areas of application. The advantages of modular solutions are: simplification of the structure, standardization of components, and faster assembly process of the complete machine Additional advantages, which is particularly important for manufacturers, are shorter manufacturing times, longer production series and reduced manufacturing costs. Modular designing is also the challenge for designers and the need for a new approach to the design process, to the starting process and to the exploitation process. The purpose for many manufacturers is the standardization of the components used for creating the finished products. This purpose could be realized by the application of standard modules which could be combined together in different ways to create the desired particular construction as much as possible in accordance with the order. This solution is for the producer more favorable than the construction of a large machine whose configuration must be matched to each individual order. In the ideal case each module has its own control system and the full functionality of the modular machine is obtained due to the mutual cooperation of all modules. Such a solution also requires the modular components which create the modular machine are equipped with interfaces compatible one with another to facilitate their communication. The individual components of the machine could be designed, manufactured and used independently and production management task could be divided into subtasks. They could be also

  18. Modeling of Agile Intelligent Manufacturing-oriented Production Scheduling System

    Institute of Scientific and Technical Information of China (English)

    Zhong-Qi Sheng; Chang-Ping Tang; Ci-Xing Lv

    2010-01-01

    Agile intelligent manufacturing is one of the new manufacturing paradigms that adapt to the fierce globalizing market competition and meet the survival needs of the enterprises, in which the management and control of the production system have surpassed the scope of individual enterprise and embodied some new features including complexity, dynamicity, distributivity, and compatibility. The agile intelligent manufacturing paradigm calls for a production scheduling system that can support the cooperation among various production sectors, the distribution of various resources to achieve rational organization, scheduling and management of production activities. This paper uses multi-agents technology to build an agile intelligent manufacturing-oriented production scheduling system. Using the hybrid modeling method, the resources and functions of production system are encapsulated, and the agent-based production system model is established. A production scheduling-oriented multi-agents architecture is constructed and a multi-agents reference model is given in this paper.

  19. Using Electromagnetic Algorithm for Total Costs of Sub-contractor Optimization in the Cellular Manufacturing Problem

    Directory of Open Access Journals (Sweden)

    Mohammad Reza Shahriari

    2016-12-01

    Full Text Available In this paper, we present a non-linear binary programing for optimizing a specific cost in cellular manufacturing system in a controlled production condition. The system parameters are determined by the continuous distribution functions. The aim of the presented model is to optimize the total cost of imposed sub-contractors to the manufacturing system by determining how to allocate the machines and parts to each seller. In this system, DM could control the occupation level of each machine in the system. For solving the presented model, we used the electromagnetic meta-heuristic algorithm and Taguchi method for determining the optimal algorithm parameters.

  20. Characterization of manufactured TiO2 nanoparticles

    Science.gov (United States)

    Motzkus, C.; Macé, T.; Vaslin-Reimann, S.; Ausset, P.; Maillé, M.

    2013-04-01

    Technological advances in nanomaterials have allowed the development of new applications in industry, increasing the probability of finding airborne manufactured and engineered nano-objects in the workplace, as well as in ambient air. Scientific studies on health and environmental risks have indicated that airborne nano-objects in ambient air have potential adverse effects on the health of exposed workers and the general population. For regulatory purposes, ambient measurements of particulate matter are based on the determination of mass concentrations for PM10 and PM2.5, as regulated in the European Directive 2008/50/EC. However, this legislation is not suitable for airborne manufactured and engineered nano-objects. Parameters characterising ultrafine particles, such as particle number concentration and size distribution, are under consideration for future health-based legislation, to monitor workplaces and to control industrial processes. Currently, there are no existing regulations covering manufactured airborne nano-objects. There is therefore a clear, unaddressed need to focus on the toxicology and exposure assessment of nano-objects such as titanium dioxide (TiO2), which are manufactured and engineered in large quantities in industry. To perform reliable toxicology studies it is necessary to determine the relevant characteristics of nano-objects, such as morphology, surface area, agglomeration, chemical composition, particle size and concentration, by applying traceable methods. Manufacturing of nanomaterials, and their use in industrial applications, also require traceable characterisation of the nanomaterials, particularly for quality control of the process. The present study arises from the OECD WPMN sponsorship programme, supported by the French Agency for Environmental and Occupational Health Safety (ANSES), in order to develop analytical methods for the characterization of TiO2 nanoparticles in size and count size distribution, based on different