WorldWideScience

Sample records for control device final

  1. Final Stormwater Control and Devices Environmental Assessment

    Science.gov (United States)

    2005-08-18

    wood nettle (Laportea canadensis), stinging nettle ( Urtica dioica ), and beggar ticks (Bidens frondosa) (Grand Forks AFB, 2003). The slopes of the...the water quality of the receiving waters. The proposed flow control structures would effectively reduce the potential impact of discharges from the...Alternative 2, and the No Action Alternative. Feasible alternatives should be low cost so they can be built with available funding; effectively control

  2. 77 FR 64827 - Certain Lighting Control Devices Including Dimmer Switches and Parts Thereof (IV); Final...

    Science.gov (United States)

    2012-10-23

    ... COMMISSION Certain Lighting Control Devices Including Dimmer Switches and Parts Thereof (IV); Final... against infringing lighting control devices including dimmer switches and parts thereof, and cease and... States after importation of certain lighting control devices including dimmer switches and parts thereof...

  3. Medical Devices; Immunology and Microbiology Devices; Classification of the Assayed Quality Control Material for Clinical Microbiology Assays. Final order.

    Science.gov (United States)

    2017-07-27

    The Food and Drug Administration (FDA, Agency, or we) is classifying the assayed quality control material for clinical microbiology assays into class II (special controls). The special controls that will apply to the device are identified in this order and will be part of the codified language for the assayed quality control material for clinical microbiology assays' classification. The Agency is classifying the device into class II (special controls) to provide a reasonable assurance of safety and effectiveness of the device.

  4. Dental devices: classification of dental amalgam, reclassification of dental mercury, designation of special controls for dental amalgam, mercury, and amalgam alloy. Final rule.

    Science.gov (United States)

    2009-08-04

    The Food and Drug Administration (FDA) is issuing a final rule classifying dental amalgam into class II, reclassifying dental mercury from class I to class II, and designating a special control to support the class II classifications of these two devices, as well as the current class II classification of amalgam alloy. The three devices are now classified in a single regulation. The special control for the devices is a guidance document entitled, "Class II Special Controls Guidance Document: Dental Amalgam, Mercury, and Amalgam Alloy." This action is being taken to establish sufficient regulatory controls to provide reasonable assurance of the safety and effectiveness of these devices. Elsewhere in this issue of the Federal Register, FDA is announcing the availability of the guidance document that will serve as the special control for the devices.

  5. Dental devices: classification of dental amalgam, reclassification of dental mercury, designation of special controls for dental amalgam, mercury, and amalgam alloy; technical amendment. Final rule; technical amendment.

    Science.gov (United States)

    2010-06-11

    The Food and Drug Administration (FDA) published a final rule in the Federal Register of August 4, 2009 (74 FR 38686) which classified dental amalgam as a class II device, reclassified dental mercury from class I to class II, and designated special controls for dental amalgam, mercury, and amalgam alloy. The effective date of the rule was November 2, 2009. The final rule was published with an inadvertent error in the codified section. This document corrects that error. This action is being taken to ensure the accuracy of the agency's regulations.

  6. Process control device

    Energy Technology Data Exchange (ETDEWEB)

    Hayashi, Toshifumi; Kobayashi, Hiroshi

    1994-09-09

    A process control device comprises a memory device for memorizing a plant operation target, a plant state or a state of equipments related with each other as control data, a read-only memory device for storing programs, a plant instrumentation control device or other process control devices, an input/output device for performing input/output with an operator, and a processing device which conducts processing in accordance with the program and sends a control demand or a display demand to the input/output device. The program reads out control data relative to a predetermined operation target, compares and verify them with actual values to read out control data to be a practice premise condition which is further to be a practice premise condition if necessary, thereby automatically controlling the plant or requiring or displaying input. Practice presuming conditions for the operation target can be examined succesively in accordance with the program without constituting complicated logical figures and AND/OR graphs. (N.H.).

  7. Device Oriented Project Controller

    Energy Technology Data Exchange (ETDEWEB)

    Dalesio, Leo; Kraimer, Martin

    2013-11-20

    This proposal is directed at the issue of developing control systems for very large HEP projects. A de-facto standard in accelerator control is the Experimental Physics and Industrial Control System (EPICS), which has been applied successfully to many physics projects. EPICS is a channel based system that requires that each channel of each device be configured and controlled. In Phase I, the feasibility of a device oriented extension to the distributed channel database was demonstrated by prototyping a device aware version of an EPICS I/O controller that functions with the current version of the channel access communication protocol. Extensions have been made to the grammar to define the database. Only a multi-stage position controller with limit switches was developed in the demonstration, but the grammar should support a full range of functional record types. In phase II, a full set of record types will be developed to support all existing record types, a set of process control functions for closed loop control, and support for experimental beam line control. A tool to configure these records will be developed. A communication protocol will be developed or extensions will be made to Channel Access to support introspection of components of a device. Performance bench marks will be made on both communication protocol and the database. After these records and performance tests are under way, a second of the grammar will be undertaken.

  8. Innovative solar control devices

    OpenAIRE

    Erhorn, H.; Erhorn-Kluttig, H.

    2010-01-01

    Buildings are the EU's largest energy users, consuming over 40 % of Europe's total primary energy. One way of cutting this consumption is by avoiding or reducing cooling energy through proper solar shading. This paper presents examples of innovative solar control devices and emphasizes their relevance for the energy performance of buildings.

  9. Radiographic quality control devices.

    Science.gov (United States)

    2000-04-01

    In this study, we evaluate eight radiographic quality control (QC) devices, which noninvasively measure the output from a variety of diagnostic x-ray production systems. When used as part of a quality assurance (QA) program, radiographic QC devices help ensure that x-ray equipment is working within acceptable limits. This in turn helps ensure that high-quality images are achieved with appropriate radiation doses and that resources are used efficiently (for example, by minimizing the number of repeat exposures required). Our testing focused on the physical performance, ease of use, and service and maintenance characteristics that affect the use of these devices for periodic, routine measurements of x-ray system parameters. We found that all the evaluated models satisfactorily measure all the parameters normally needed for a QA program. However, we did identify a number of differences among the models--particularly in the range of exposure levels that can be effectively measured and the ease of use. Three models perform well for a variety of applications and are very easy to use; we rate them Preferred. Three additional models have minor limitations but otherwise perform well; we rate them Acceptable. We recommend against purchasing two models because, although each performs acceptably for most applications, neither model can measure low levels of radiation. This Evaluation covers devices designed to measure the output of x-ray tubes noninvasively. These devices, called radiographic quality control (QC) devices, or QC meters, are typically used by medical physicists, x-ray engineers, biomedical engineers, and suitably trained radiographic technologists to make QC measurements. We focus on the use of these devices as part of an overall quality assurance (QA) program. We have not evaluated their use for other applications, such as acceptance testing. To be included in this study, a device must be able to measure the exposure- and kVp-related characteristics of most x

  10. Contaminate Control Device

    Science.gov (United States)

    Howe, Robert H. (Inventor); Flynn, Kenneth P. (Inventor); Stapleton, Thomas J. (Inventor)

    2014-01-01

    A contaminate control device for filtering contaminates from a gas such as air is provided. The device includes a housing having a first inlet and a first outlet. An axial flow filter is fluidly coupled between the first inlet and the first outlet, the axial flow filter has a second inlet and a second outlet. A second filter disposed about the axial flow filter and is fluidly coupled between the first inlet and the first outlet, the second filter having a third inlet on an inner diameter and a third outlet disposed on an outer diameter. A flow restrictor is fluidly coupled between the second inlet and the first inlet.

  11. Cursor Control Device Characteristics

    Directory of Open Access Journals (Sweden)

    James Phillips

    2000-05-01

    Full Text Available An analysis of cursor positioning may provide guidelines for improvements in cursor control. Four experiments addressed efficiency of cursor control devices (Mouse, Digitising Pen, Accupoint, Trackball. Participants moved a cursor leftwards, upwards or rightwards, positioning it in large or small targets situated in near or far space on the computer screen. Cursor coordinates were sampled every 5 ms. The number of submovements and the proportion of time spent in deceleration were analysed. Participants could not plan movements controlled by an Accupoint. Cursor trajectories were more variable in near space for detachable manipulanda due to potential cartesian coordinate system incompatibilities

  12. Gaseous Fluidics Control Device

    Directory of Open Access Journals (Sweden)

    Brahim, DENNAI

    2008-04-01

    Full Text Available Fluidics is a new technology arising from a re-appraisal of a very old technology, namely fluid power and its control. Fluidic technology based on natural oscillation phenomena is a relevant topic in several strategic areas. This technology of using the flow characteristics of liquids or gases to operate a control system is fairly old; it was in the 1960s that researchers started to use fluidics. Important contributions from fluidic logic technologies are associated with the fluid behavior known as the “Coanda effect”. A lot of attention has been paid to the transport phenomena in the micro geometries because micro fabrication enables us to manufacture low channels ranging from few micrometers to few hundred micrometers. This paper describes a new actuator for flow control applications. The gas diffusion, control is very important operation in the fields of nature and industry.

  13. Gaseous Fluidics Control Device

    OpenAIRE

    Brahim, Dennai; Rachid KHELFAOUI; Boumedienne BENYOUCEF; Belkacem DRAOUI; Abdelkader SLIMANI

    2008-01-01

    Fluidics is a new technology arising from a re-appraisal of a very old technology, namely fluid power and its control. Fluidic technology based on natural oscillation phenomena is a relevant topic in several strategic areas. This technology of using the flow characteristics of liquids or gases to operate a control system is fairly old; it was in the 1960s that researchers started to use fluidics. Important contributions from fluidic logic technologies are associated with the fluid behavior kn...

  14. Development of cryotribological theories & application to cryogenic devices. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Iwasa, Yukikazu

    2001-03-12

    This is the final report of a research program on low-temperature friction and wear, primarily focused on development of cryotribological theories and application to cryogenic devices, particularly superconducting magnets.

  15. Connected Cruise Control : Final report

    NARCIS (Netherlands)

    van Arem, B.

    2013-01-01

    This report describes the final results of the Connected Cruise Control project. The
    Connected Cruise Control project was conducted from December 2009-April 2013 as a High Tech Automotive System Innovation project (HTASD09002), subsidized by
    Agentschap NL. The project was conducted by a

  16. Compact, Controlled Resistance Exercise Device

    Science.gov (United States)

    Paulus, David C.; DeWitt, John K.; Reich, Alton J.; Shaw, James E.; Deaconu, Stelu S.

    2011-01-01

    Spaceflight leads to muscle and bone atrophy. Isoinertial (free-weight) exercises provide a sufficient stimulus to elicit increases in both muscle strength and bone mineral density in Earth-based studies. While exercise equipment is in use on the International Space Station for crewmember health maintenance, current devices are too large to place in a transport vehicle or small spacecraft. Therefore, a portable computer controlled resistance exercise device is being developed that is able to simulate the inertial loading experienced when lifting a mass on Earth. This portable device weighs less than 50 lb and can simulate the resistance of lifting and lowering up to 600 lb of free-weights. The objective is to allow crewmembers to perform resistance exercise with loads capable of maintaining muscle and bone health. The device is reconfigurable and allows for the performance of typical Earth-based free-weight exercises. Forces exerted, volume of work, range of motion, time-under-tension, and speed/ acceleration of movement are recorded and can be remotely monitored to track progress and modify individual protocols based on exercise session data. A performance evaluation will be completed and data will be presented that include ground-reaction force comparisons between the device and free-weight dead-lifts over a spectrum of resistance levels. Movement biomechanics will also be presented.

  17. Evaluation of traffic control devices : fifth-year activities.

    Science.gov (United States)

    2009-02-01

    This project was established to provide a means of conducting limited scope evaluations of numerous traffic : control device issues. During the fifth, and final, year of the project, researchers conducted four activities: : improving the interface fo...

  18. Medical Devices; Ophthalmic Devices; Classification of the Oral Electronic Vision Aid. Final order.

    Science.gov (United States)

    2015-09-22

    The Food and Drug Administration (FDA) is classifying the oral electronic vision aid into class II (special controls). The special controls that will apply to the device are identified in this order and will be part of the codified language for the oral electronic vision aid's classification. The Agency is classifying the device into class II (special controls) in order to provide a reasonable assurance of safety and effectiveness of the device.

  19. Medical Devices; General and Plastic Surgery Devices; Classification of the Magnetic Surgical Instrument System. Final order.

    Science.gov (United States)

    2016-09-21

    The Food and Drug Administration (FDA) is classifying the Magnetic Surgical Instrument System into class II (special controls). The special controls that will apply to the device are identified in this order and will be part of the codified language for the magnetic surgical instrument system's classification. The Agency is classifying the device into class II (special controls) in order to provide a reasonable assurance of safety and effectiveness of the device.

  20. Virtualized Network Control. Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Ghani, Nasir [Univ. of New Mexico, Albuquerque, NM (United States)

    2013-02-01

    This document is the final report for the Virtualized Network Control (VNC) project, which was funded by the United States Department of Energy (DOE) Office of Science. This project was also informally referred to as Advanced Resource Computation for Hybrid Service and TOpology NEtworks (ARCHSTONE). This report provides a summary of the project's activities, tasks, deliverable, and accomplishments. It also provides a summary of the documents, software, and presentations generated as part of this projects activities. Namely, the Appendix contains an archive of the deliverables, documents, and presentations generated a part of this project.

  1. Medical Devices; Immunology and Microbiology Devices; Classification of the BCR–ABL Quantitation Test. Final order.

    Science.gov (United States)

    2017-11-01

    The Food and Drug Administration (FDA or we) is classifying the BCR-ABL quantitation test into class II (special controls). The special controls that apply to the device type are identified in this order and will be part of the codified language for the BCR-ABL quantitation test's classification. We are taking this action because we have determined that classifying the device into class II (special controls) will provide a reasonable assurance of safety and effectiveness of the device. We believe this action will also enhance patients' access to beneficial innovative devices, in part by reducing regulatory burdens.

  2. Medical Devices; Immunology and Microbiology Devices; Classification of the Genetic Health Risk Assessment System. Final order.

    Science.gov (United States)

    2017-11-07

    The Food and Drug Administration (FDA, the Agency, or we) is classifying the genetic health risk assessment system into class II (special controls). The special controls that apply to the device type are identified in this order and will be part of the codified language for the genetic health risk assessment system's classification. We are taking this action because we have determined that classifying the device into class II (special controls) will provide a reasonable assurance of safety and effectiveness of the device. We believe this action will also enhance patients' access to beneficial innovative devices, in part by reducing regulatory burdens.

  3. Medical Devices; Clinical Chemistry and Clinical Toxicology Devices; Classification of the Organophosphate Test System. Final order.

    Science.gov (United States)

    2017-10-18

    The Food and Drug Administration (FDA or we) is classifying the organophosphate test system into class II (special controls). The special controls that apply to the device type are identified in this order and will be part of the codified language for the organophosphate test system's classification. We are taking this action because we have determined that classifying the device into class II (special controls) will provide a reasonable assurance of safety and effectiveness of the device. We believe this action will also enhance patients' access to beneficial innovative devices, in part by reducing regulatory burdens.

  4. Medical Devices; Hematology and Pathology Devices; Classification of a Cervical Intraepithelial Neoplasia Test System. Final order.

    Science.gov (United States)

    2018-01-03

    The Food and Drug Administration (FDA or we) is classifying the cervical intraepithelial neoplasia (CIN) test system into class II (special controls). The special controls that apply to the device type are identified in this order and will be part of the codified language for the CIN test system's classification. We are taking this action because we have determined that classifying the device into class II (special controls) will provide a reasonable assurance of safety and effectiveness of the device. We believe this action will also enhance patients' access to beneficial innovative devices, in part by reducing regulatory burdens.

  5. Field studies of beach cones as coastal erosion control/reversal devices for areas with significant oil and gas activities. Final report, February 24, 1992--September 18, 1995

    Energy Technology Data Exchange (ETDEWEB)

    Law, V.J.

    1995-09-18

    The primary objective of this project was to evaluate the utility of a device called the {open_quotes}beach cone{close_quotes} in combating coastal erosion. Seven initial sites were selected for testing beach cones in a variety of geometric configurations. Permits were obtained from the State of Louisiana and the U.S. Army Corps of Engineers to perform the work associated with this study. Six hundred beach cones were actually installed at six of the sites in late July and early August, 1992. Findings indicate that beach cones accreted significant amounts of materials along the beach of a barrier island, and they might have been instrumental in repairing an approximately 200 meter gap in the island. At the eighth installation the amount of accreted material was measured by surveys to be 2200 cubic meters (2900 cubic yards) in February of 1993, when the cones were found to have been completely covered by the material. At other test sites, accretion rates have been less dramatic but importantly, no significant additional erosion has occurred, which is a positive result. The cost of sediment accretion using beach cones was found to be about $13.72 per cubic yard, which would be much lower if the cones were mass produced (on the order of $3.00 per cubic yard). The survival of the cones through the fringes of Hurricane Andrew indicates that they can be anchored sufficiently to survive significant storms. The measurements of the cones settling rates indicate that this effect is not significant enough to hinder their effectiveness. A subcontract to Xavier University to assess the ecological quality of the experimental sites involved the study of the biogeochemical cycle of trace metals. The highest concentration of heavy metals were near a fishing camp while the lowest levels were in the beach sand of a barrier island. This suggests that the metals do not occur naturally in these areas, but have been placed in the sediments by man`s activities.

  6. Medical Devices; Exemption From Premarket Notification; Class II Devices; Electric Positioning Chair. Final order.

    Science.gov (United States)

    2015-11-20

    The Food and Drug Administration (FDA or the Agency) is publishing an order granting a petition requesting exemption from premarket notification requirements for electric positioning chair devices. An electric positioning chair is a device with a motorized positioning control that is intended for medical purposes and that can be adjusted to various positions. These devices are used to provide stability for patients with athetosis (involuntary spasms) and to alter postural positions. This order exempts electric positioning chairs, class II devices, from premarket notification, subject to certain conditions for exemption. This exemption from premarket notification, subject to these conditions (and the limitations in the physical medicine devices limitations of exemptions from premarket notification section of the device regulations), is immediately in effect for electric positioning chairs. FDA is publishing this order in accordance with the exemption from class II premarket notification section of the Federal Food, Drug, and Cosmetic Act (the FD&C Act).

  7. Predistortion control device and method, assembly including a predistortion control device

    NARCIS (Netherlands)

    Kokkeler, Andre B.J.

    2003-01-01

    A predistortion control device (1). The device has a first predistortion control input connectable to a power amplifier output (21); a second predistortion control input (11) connectable to a signal contact of a predistortion device; and a predistortion control output (12) connectable to a control

  8. Cursor Control Device Test Battery

    Science.gov (United States)

    Holden, Kritina; Sandor, Aniko; Pace, John; Thompson, Shelby

    2013-01-01

    The test battery was developed to provide a standard procedure for cursor control device evaluation. The software was built in Visual Basic and consists of nine tasks and a main menu that integrates the set-up of the tasks. The tasks can be used individually, or in a series defined in the main menu. Task 1, the Unidirectional Pointing Task, tests the speed and accuracy of clicking on targets. Two rectangles with an adjustable width and adjustable center- to-center distance are presented. The task is to click back and forth between the two rectangles. Clicks outside of the rectangles are recorded as errors. Task 2, Multidirectional Pointing Task, measures speed and accuracy of clicking on targets approached from different angles. Twenty-five numbered squares of adjustable width are arranged around an adjustable diameter circle. The task is to point and click on the numbered squares (placed on opposite sides of the circle) in consecutive order. Clicks outside of the squares are recorded as errors. Task 3, Unidirectional (horizontal) Dragging Task, is similar to dragging a file into a folder on a computer desktop. Task 3 requires dragging a square of adjustable width from one rectangle and dropping it into another. The width of each rectangle is adjustable, as well as the distance between the two rectangles. Dropping the square outside of the rectangles is recorded as an error. Task 4, Unidirectional Path Following, is similar to Task 3. The task is to drag a square through a tunnel consisting of two lines. The size of the square and the width of the tunnel are adjustable. If the square touches any of the lines, it is counted as an error and the task is restarted. Task 5, Text Selection, involves clicking on a Start button, and then moving directly to the underlined portion of the displayed text and highlighting it. The pointing distance to the text is adjustable, as well as the to-be-selected font size and the underlined character length. If the selection does not

  9. Electronic control of magnonic and spintronic devices

    OpenAIRE

    Tannous, C.; Gieraltowski, J.

    2016-01-01

    Nanometric magnonic and spintronic devices need magnetic field control in addition to conventional electronic control. In this work we review ways to replace magnetic field control by an electronic one in order to circumvent appearance of stray magnetic fields or the difficulty of creating large magnetic fields over nanometric distances. Voltage control is compared to current control and corresponding devices are compared from their energetic efficiency point of view.

  10. 78 FR 5207 - Certain Led Photographic Lighting Devices and Components Thereof; Commission's Final...

    Science.gov (United States)

    2013-01-24

    ... COMMISSION Certain Led Photographic Lighting Devices and Components Thereof; Commission's Final Determination... general exclusion order prohibiting importation of infringing LED photographic lighting devices and... importation of certain LED photographic lighting devices and components thereof that infringe certain claims...

  11. Control method for physical systems and devices

    Science.gov (United States)

    Guckenheimer, John

    1997-01-01

    A control method for stabilizing systems or devices that are outside the control domain of a linear controller is provided. When applied to nonlinear systems, the effectiveness of this method depends upon the size of the domain of stability that is produced for the stabilized equilibrium. If this domain is small compared to the accuracy of measurements or the size of disturbances within the system, then the linear controller is likely to fail within a short period. Failure of the system or device can be catastrophic: the system or device can wander far from the desired equilibrium. The method of the invention presents a general procedure to recapture the stability of a linear controller, when the trajectory of a system or device leaves its region of stability. By using a hybrid strategy based upon discrete switching events within the state space of the system or device, the system or device will return from a much larger domain to the region of stability utilized by the linear controller. The control procedure is robust and remains effective under large classes of perturbations of a given underlying system or device.

  12. Fast-acting nuclear reactor control device

    Science.gov (United States)

    Kotlyar, Oleg M.; West, Phillip B.

    1993-01-01

    A fast-acting nuclear reactor control device for moving and positioning a fety control rod to desired positions within the core of the reactor between a run position in which the safety control rod is outside the reactor core, and a shutdown position in which the rod is fully inserted in the reactor core. The device employs a hydraulic pump/motor, an electric gear motor, and solenoid valve to drive the safety control rod into the reactor core through the entire stroke of the safety control rod. An overrunning clutch allows the safety control rod to freely travel toward a safe position in the event of a partial drive system failure.

  13. Robotics and teleoperator-controlled devices.

    Science.gov (United States)

    Meieran, H B

    1988-08-01

    This paper presents a rationale for and a summary of tasks and missions to which mobile and stationary robots and other teleoperator-controlled devices could be assigned in response to the accidental release of radioactive and other hazardous/toxic materials to the environment. Many of these vehicles and devices currently support operation and maintenance of nuclear power plants and other nuclear industry facilities. This paper also discusses specific missions for these devices at the Three Mile Island and Chernobyl nuclear power plant sites at the time of the accidents. Also discussed is the status of devices under development for future applications, as well as research on robotics.

  14. Controlling Devices Using Biological Signals

    Directory of Open Access Journals (Sweden)

    Alexandre Santos Brandão

    2011-08-01

    Full Text Available Knowing that the driving task of a conventional wheelchair could be difficult or even impossible for impairment people, this work presents an overview of some strategies developed to aid these people. Within this context, a myoelectrical eye-blink and an iris tracking system to guide a robotic wheelchair are briefly described. Futhermore, some comments about EEG-based systems are also presented. Finally, it is presented a robotic wheelchair navigation system capable to reach a desired pose in a planar environment while avoiding static and dynamic obstacles.

  15. Traffic control device evaluation program : FY 2016.

    Science.gov (United States)

    2017-03-01

    This report presents findings on three different activities conducted in the Traffic Control Device Evaluation Program during the 2016 fiscal year. The first two activities are evaluations of full-matrix color light-emitting diode changeable message ...

  16. Volume control device for digital signals

    NARCIS (Netherlands)

    Schinkel, Daniel; van Tuijl, Adrianus Johannes Maria; Nuijten, Petrus A.C.M.

    2004-01-01

    A digital volume control device comprises a logic unit for volume control of digital input signals. Successively supplied m-bits words with maximally k bits active, derived from the output signals of or supplied by a volume control (4) with a quantizer (5) element the filtered m-bits workds are

  17. THORs Power Method for Hydrokinetic Devices - Final Report

    Energy Technology Data Exchange (ETDEWEB)

    J. Turner Hunt; Joel Rumker

    2012-08-08

    Ocean current energy represents a vast untapped source of renewable energy that exists on the outer continental shelf areas of the 5 major continents. Ocean currents are unidirectional in nature and are perpetuated by thermal and salinity sea gradients, as well as coriolis forces imparted from the earth's rotation. This report details THORs Power Method, a breakthrough power control method that can provide dramatic increases to the capacity factor over and above existing marine hydrokinetic (MHK) devices employed in the extraction of energy from ocean currents. THORs Power Method represents a constant speed, variable depth operational method that continually locates the ocean current turbine at a depth at which the rated power of the generator is routinely achieved. Variable depth operation is achieved by using various vertical force effectors, including ballast tanks for variable weight, a hydrodynamic wing for variable lift or down force and drag flaps for variable vehicle drag forces.

  18. Infrared control coating of thin film devices

    Energy Technology Data Exchange (ETDEWEB)

    Berland, Brian Spencer; Stowell, Jr., Michael Wayne; Hollingsworth, Russell

    2017-02-28

    Systems and methods for creating an infrared-control coated thin film device with certain visible light transmittance and infrared reflectance properties are disclosed. The device may be made using various techniques including physical vapor deposition, chemical vapor deposition, thermal evaporation, pulsed laser deposition, sputter deposition, and sol-gel processes. In particular, a pulsed energy microwave plasma enhanced chemical vapor deposition process may be used. Production of the device may occur at speeds greater than 50 Angstroms/second and temperatures lower than 200.degree. C.

  19. Medical devices; general and plastic surgery devices; classification of the focused ultrasound stimulator system for aesthetic use. Final rule.

    Science.gov (United States)

    2011-07-20

    The Food and Drug Administration (FDA) is classifying the focused ultrasound stimulator system for aesthetic use into class II (special controls). The special control(s) that will apply to the device is the guidance document entitled "Class II Special Controls Guidance Document: Focused Ultrasound Stimulator System for Aesthetic Use." The Agency is classifying the device into class II (special controls) in order to provide a reasonable assurance of safety and effectiveness of the device.

  20. Emissions from street vendor cooking devices (charcoal grilling). Final report, January 1998--March 1999

    Energy Technology Data Exchange (ETDEWEB)

    Lee, S.Y.

    1999-06-01

    The report discusses a joint US/Mexican program to establish a reliable emissions inventory for street vendor cooking devices (charcoal grilling), a significant source of air pollutants in the Mexicali-Imperial Valley area of Mexico. Emissions from these devices, prevalent in the streets of Mexicali, Mexico, were investigated experimentally by measuring levels of particulate matter, particle size distributions, volatile and semivolatile organic compounds, aldehydes, and oxides of nitrogen and sulfur, emitted when meat is cooked on a grill over a charcoal fire. To investigate the emission rate, both beef and chicken were tested. Furthermore, both meats were marinated with a mixture similar to that used by the street vendors. Some tests were conducted with non-marinated beef for comparison. Two blank runs were performed sampling charcoal fires without meat. Finally, a simple control device, normally used in an exhaust fan to trap grease over a kitchen stove, was evaluated for its effectiveness in reducing emissions.

  1. Medical devices; general and plastic surgery devices; classification of the low level laser system for aesthetic use. Final rule.

    Science.gov (United States)

    2011-04-14

    The Food and Drug Administration (FDA) is classifying the low level laser system for aesthetic use into class II (special controls). The special control(s) that will apply to the device is entitled ``Class II Special Controls Guidance Document: Low Level Laser System for Aesthetic Use.'' The Agency is classifying the device into class II (special controls) in order to provide a reasonable assurance of safety and effectiveness of the device. Elsewhere in this issue of the Federal Register, FDA is announcing the availability of a guidance document that will serve as the special control for this device type.

  2. Practical design control implementation for medical devices

    CERN Document Server

    Justiniano, Jose

    2003-01-01

    Bringing together the concepts of design control and reliability engineering, this book is a must for medical device manufacturers. It helps them meet the challenge of designing and developing products that meet or exceed customer expectations and also meet regulatory requirements. Part One covers motivation for design control and validation, design control requirements, process validation and design transfer, quality system for design control, and measuring design control program effectiveness. Part Two discusses risk analysis and FMEA, designing-in reliability, reliability and design verific

  3. Plasma surface interactions in controlled fusion devices

    Energy Technology Data Exchange (ETDEWEB)

    Ghendrih, Ph.; Becoulet, M.; Costanzo, L. [and others

    2000-07-01

    This report brings together all the contributions of EURATOM/CEA association to the 14. international conference on plasma surface interactions in controlled fusion devices. 24 papers are presented and they deal mainly with the ergodic divertor and the first wall of Tore-supra tokamak.

  4. Fluid control structures in microfluidic devices

    Energy Technology Data Exchange (ETDEWEB)

    Mathies, Richard A.; Grover, William H.; Skelley, Alison; Lagally, Eric; Liu, Chung N.

    2017-05-09

    Methods and apparatus for implementing microfluidic analysis devices are provided. A monolithic elastomer membrane associated with an integrated pneumatic manifold allows the placement and actuation of a variety of fluid control structures, such as structures for pumping, isolating, mixing, routing, merging, splitting, preparing, and storing volumes of fluid. The fluid control structures can be used to implement a variety of sample introduction, preparation, processing, and storage techniques.

  5. Design controls for the medical device industry

    CERN Document Server

    Teixeira, Marie B

    2013-01-01

    The second edition of a bestseller, Design Controls for the Medical Device Industry provides a comprehensive review of the latest design control requirements, as well as proven tools and techniques to ensure your company's design control program evolves in accordance with current industry practice. The text assists in the development of an effective design control program that not only satisfies the US FDA Quality System Regulation (QSR) and ISO 9001 and 13485 standards, but also meets today's third-party auditor/investigator expectations and saves you valuable time and money.The author's cont

  6. Medical Devices; General Hospital and Personal Use Devices; Classification of the Image Processing Device for Estimation of External Blood Loss. Final order.

    Science.gov (United States)

    2017-12-20

    The Food and Drug Administration (FDA or we) is classifying the image processing device for estimation of external blood loss into class II (special controls). The special controls that apply to the device type are identified in this order and will be part of the codified language for the image processing device for estimation of external blood loss' classification. We are taking this action because we have determined that classifying the device into class II (special controls) will provide a reasonable assurance of safety and effectiveness of the device. We believe this action will also enhance patients' access to beneficial innovative devices, in part by reducing regulatory burdens.

  7. Wind turbine remote control using Android devices

    Science.gov (United States)

    Rat, C. L.; Panoiu, M.

    2018-01-01

    This paper describes the remote control of a wind turbine system over the internet using an Android device, namely a tablet or a smartphone. The wind turbine workstation contains a LabVIEW program which monitors the entire wind turbine energy conversion system (WECS). The Android device connects to the LabVIEW application, working as a remote interface to the wind turbine. The communication between the devices needs to be secured because it takes place over the internet. Hence, the data are encrypted before being sent through the network. The scope was the design of remote control software capable of visualizing real-time wind turbine data through a secure connection. Since the WECS is fully automated and no full-time human operator exists, unattended access to the turbine workstation is needed. Therefore the device must not require any confirmation or permission from the computer operator in order to control it. Another condition is that Android application does not have any root requirements.

  8. Medical Devices; Immunology and Microbiology Devices; Classification of the Streptococcus SPP. Nucleic Acid-Based Assay. Final order.

    Science.gov (United States)

    2017-10-30

    The Food and Drug Administration (FDA or we) is classifying the Streptococcus spp. nucleic acid-based assay into class II (special controls). The special controls that apply to the device type are identified in this order and will be part of the codified language for the Streptococcus spp. nucleic acid-based assay's classification. We are taking this action because we have determined that classifying the device into class II (special controls) will provide a reasonable assurance of safety and effectiveness of the device. We believe this action will also enhance patients' access to beneficial innovative devices, in part by reducing regulatory burdens.

  9. Medical Devices; Immunology and Microbiology Devices; Classification of the Aquaporin-4 Autoantibody Immunological Test System. Final order.

    Science.gov (United States)

    2017-10-30

    The Food and Drug Administration (FDA or we) is classifying the Aquaporin-4 autoantibody immunological test system into class II (special controls). The special controls that apply to the device type are identified in this order and will be part of the codified language for the Aquaporin-4 autoantibody immunological test system's classification. We are taking this action because we have determined that classifying the device into class II (special controls) will provide a reasonable assurance of safety and effectiveness of the device. We believe this action will also enhance patients' access to beneficial innovative devices, in part by reducing regulatory burdens.

  10. Medical Devices; Immunology and Microbiology Devices; Classification of the Zinc Transporter 8 Autoantibody Immunological Test System. Final order.

    Science.gov (United States)

    2017-10-24

    The Food and Drug Administration (FDA or we) is classifying the zinc transporter 8 autoantibody immunological test system into class II (special controls). The special controls that apply to the device type are identified in this order and will be part of the codified language for the zinc transporter 8 autoantibody immunological test system's classification. We are taking this action because we have determined that classifying the device into class II (special controls) will provide a reasonable assurance of safety and effectiveness of the device. We believe this action will also enhance patients' access to beneficial innovative devices, in part by reducing regulatory burdens.

  11. Medical Devices; Immunology and Microbiology Devices; Classification of the Newborn Screening Test for Severe Combined Immunodeficiency Disorder. Final order.

    Science.gov (United States)

    2017-10-30

    The Food and Drug Administration (FDA or we) is classifying the newborn screening test for severe combined immunodeficiency disorder (SCID) into class II (special controls). The special controls that apply to the device type are identified in this order and will be part of the codified language for the newborn screening test for SCID's classification. We are taking this action because we have determined that classifying the device into class II (special controls) will provide a reasonable assurance of safety and effectiveness of the device. We believe this action will also enhance patients' access to beneficial innovative devices, in part by reducing regulatory burdens.

  12. Medical Devices; Immunology and Microbiology Devices; Classification of the Automated Indirect Immunofluorescence Microscope and Software-Assisted System. Final order.

    Science.gov (United States)

    2017-11-14

    The Food and Drug Administration (FDA or we) is classifying the automated indirect immunofluorescence microscope and software-assisted system into class II (special controls). The special controls that apply to the device type are identified in this order and will be part of the codified language for the automated indirect immunofluorescence microscope and software-assisted system's classification. We are taking this action because we have determined that classifying the device into class II (special controls) will provide a reasonable assurance of safety and effectiveness of the device. We believe this action will also enhance patients' access to beneficial innovative devices, in part by reducing regulatory burdens.

  13. Physical Medicine Devices; Reclassification of Shortwave Diathermy for All Other Uses, Henceforth To Be Known as Nonthermal Shortwave Therapy. Final order; technical correction.

    Science.gov (United States)

    2015-10-13

    The Food and Drug Administration (FDA) is issuing a final order to reclassify shortwave diathermy (SWD) for all other uses, a preamendments class III device, into class II (special controls), and to rename the device "nonthermal shortwave therapy'' (SWT). FDA is also making a technical correction in the regulation for the carrier frequency for SWD and SWT devices.

  14. 14 CFR 25.697 - Lift and drag devices, controls.

    Science.gov (United States)

    2010-01-01

    ... 14 Aeronautics and Space 1 2010-01-01 2010-01-01 false Lift and drag devices, controls. 25.697....697 Lift and drag devices, controls. (a) Each lift device control must be designed so that the pilots....101(d). Lift and drag devices must maintain the selected positions, except for movement produced by an...

  15. Respiratory protective device design using control system techniques

    Science.gov (United States)

    Burgess, W. A.; Yankovich, D.

    1972-01-01

    The feasibility of a control system analysis approach to provide a design base for respiratory protective devices is considered. A system design approach requires that all functions and components of the system be mathematically identified in a model of the RPD. The mathematical notations describe the operation of the components as closely as possible. The individual component mathematical descriptions are then combined to describe the complete RPD. Finally, analysis of the mathematical notation by control system theory is used to derive compensating component values that force the system to operate in a stable and predictable manner.

  16. Medical devices; immunology and microbiology devices; classification of respiratory viral panel multiplex nucleic acid assay. Final rule.

    Science.gov (United States)

    2009-10-09

    The Food and Drug Administration (FDA) is announcing the classification of the respiratory viral panel multiplex nucleic acid assay into class II (special controls). The special controls that will apply to the device are three guidance documents entitled: "Class II Special Controls Guidance Document: Respiratory Viral Panel Multiplex Nucleic Acid Assay," as applicable, "Class II Special Controls Guidance Document: Testing for Human Metapneumovirus (hMPV) Using Nucleic Acid Assays," and as applicable,"Class II Special Controls Guidance Document: Testing for Detection and Differentiation of Influenza A Virus Subtypes Using Multiplex Nucleic Acid Assays.'' The agency classified the device into class II (special controls) in order to provide a reasonable assurance of safety and effectiveness of the device. Elsewhere in this issue of the Federal Register, FDA is announcing the availability of the guidance documents that will serve as the special controls for this device.

  17. Friction measuring device for control rod

    Energy Technology Data Exchange (ETDEWEB)

    Sato, Tomomi.

    1994-03-18

    In the present invention, judgment for friction of control rods conducted upon periodical inspection of a BWR type power plant is conducted by automatic analysis and evaluation by digitalizing data of an operation pressure and an differential pressure of control rods. That is, a differential pressure detection means detects a pressure and a differential pressure of driving water of a control rod driving source. A data processing device conducts digital analysis and store data from the differential pressure detection means, as well as compares the data with set values to automatically judge the friction of the control rod to diagnose abnormality based on the changing trend of the analyzed data. According to the device of the present invention, data measured for the friction of a great number of control rods can be analyzed and judged automatically in a short period of time. Accordingly, evaluation can be conducted accurately even by less skilled operators. Further, when an abnormality is detected, the diagnosis thereof is conducted, so that the operation is simplified and an operator's burden upon inspection can be mitigated. (I.S.).

  18. Device Control Using Gestures Sensed from EMG

    Science.gov (United States)

    Wheeler, Kevin R.

    2003-01-01

    In this paper we present neuro-electric interfaces for virtual device control. The examples presented rely upon sampling Electromyogram data from a participants forearm. This data is then fed into pattern recognition software that has been trained to distinguish gestures from a given gesture set. The pattern recognition software consists of hidden Markov models which are used to recognize the gestures as they are being performed in real-time. Two experiments were conducted to examine the feasibility of this interface technology. The first replicated a virtual joystick interface, and the second replicated a keyboard.

  19. 30 CFR 75.330 - Face ventilation control devices.

    Science.gov (United States)

    2010-07-01

    ... control devices. (a) Brattice cloth, ventilation tubing and other face ventilation control devices shall... maintaining concentrations of respirable dust, methane, and other harmful gases, in accordance with the levels...

  20. Medical Devices; Immunology and Microbiology Devices; Classification of the Device To Detect and Identify Microbial Pathogen Nucleic Acids in Cerebrospinal Fluid. Final order.

    Science.gov (United States)

    2017-10-20

    The Food and Drug Administration (FDA or we) is classifying the device to detect and identify microbial pathogen nucleic acids in cerebrospinal fluid into class II (special controls). The special controls that will apply to the device type are identified in this order and will be part of the codified language for the device to detect and identify microbial pathogen nucleic acids in cerebrospinal fluid’s classification. We are taking this action because we have determined that classifying the device into class II (special controls) will provide a reasonable assurance of safety and effectiveness of the device. We believe this action will also enhance patients' access to beneficial innovative devices, in part by reducing regulatory burdens.

  1. Brain-controlled body movement assistance devices and methods

    Energy Technology Data Exchange (ETDEWEB)

    Leuthardt, Eric C.; Love, Lonnie J.; Coker, Rob; Moran, Daniel W.

    2017-01-10

    Methods, devices, systems, and apparatus, including computer programs encoded on a computer storage medium, for brain-controlled body movement assistance devices. In one aspect, a device includes a brain-controlled body movement assistance device with a brain-computer interface (BCI) component adapted to be mounted to a user, a body movement assistance component operably connected to the BCI component and adapted to be worn by the user, and a feedback mechanism provided in connection with at least one of the BCI component and the body movement assistance component, the feedback mechanism being configured to output information relating to a usage session of the brain-controlled body movement assistance device.

  2. Design control considerations for biologic-device combination products.

    Science.gov (United States)

    Anderson, Dave; Liu, Roger; Anand Subramony, J; Cammack, Jon

    2017-03-01

    Combination products are therapeutic and diagnostic medical products that combine drugs, devices, and/or biological products with one another. Historically, biologics development involved identifying efficacious doses administered to patients intravenously or perhaps by a syringe. Until fairly recently, there has been limited focus on developing an accompanying medical device, such as a prefilled syringe or auto-injector, to enable easy and more efficient delivery. For the last several years, and looking forward, where there may be little to distinguish biologics medicines with relatively similar efficacy profiles, the biotechnology market is beginning to differentiate products by patient-focused, biologic-device based combination products. As innovative as biologic-device combination products are, they can pose considerable development, regulatory, and commercialization challenges due to unique physicochemical properties and special clinical considerations (e.g., dosing volumes, frequency, co-medications, etc.) of the biologic medicine. A biologic-device combination product is a marriage between two partners with "cultural differences," so to speak. There are clear differences in the development, review, and commercialization processes of the biologic and the device. When these two cultures come together in a combination product, developers and reviewers must find ways to address the design controls and risk management processes of both the biologic and device, and knit them into a single entity with supporting product approval documentation. Moreover, digital medicine and connected health trends are pushing the boundaries of combination product development and regulations even further. Despite an admirable cooperation between industry and FDA in recent years, unique product configurations and design features have resulted in review challenges. These challenges have prompted agency reviewers to modernize consultation processes, while at the same time, promoting

  3. 77 FR 51573 - Certain Automated Media Library Devices; Determination To Review in Part a Final Initial...

    Science.gov (United States)

    2012-08-24

    ... COMMISSION Certain Automated Media Library Devices; Determination To Review in Part a Final Initial.... KG of Rottweil, Germany; BDT Automation Technology (Zhuhai FTZ), Co., Ltd. of Zhuhai Guandang, China... Automation Technology (Zhuhai FTZ), Co., Ltd., BDT de Mexico, S. de R.L. de C.V., and BDT Products, Inc...

  4. 78 FR 37569 - Certain Kinesiotherapy Devices and Components Thereof Final Commission Determination of Violation...

    Science.gov (United States)

    2013-06-21

    ... COMMISSION Certain Kinesiotherapy Devices and Components Thereof Final Commission Determination of Violation.... International Trade Commission has terminated the above-captioned investigation with a finding of violation of...''). 77 FR 1504 (Jan. 10, 2012). The complaint alleged violations of section 337 of the Tariff Act of 1930...

  5. Implementation of vortex wake control using SMA-actuated devices

    Science.gov (United States)

    Quackenbush, Todd R.; Bilanin, Alan J.; Batcho, P. F.; McKillip, Robert M., Jr.; Carpenter, Bernie F.

    1997-05-01

    Mitigation of the undesirable effects of trailing vortex wakes has been a long-standing priority for both reduction of submarine wake signature and alleviation of aircraft vortex wake hazard. A recent study established the feasibility of using relatively weak, secondary vortices with carefully selected unsteady amplitude and phasing to accelerate the breakup of the primary vortex system of a lifting surface, a technique denoted `vortex leveraging'. This paper will summarize progress on the development of SMA-actuated devices for implementing vortex leveraging for hydrodynamic applications. The methods being applied to the hydrodynamic design of these deformable Smart Vortex Leveraging Tabs (SVLTs) will be described, and the results of a preliminary assessment of SVLT performance in achieving wake breakup will be presented. Also, previous work on the design and testing of deformable control surfaces actuated via embedded SMA agonist wires will be reviewed and the design process being employed in the present applications will be discussed. Finally, the plans for near-term computational and experimental work to validate the use of SMA-driven devices for the wake mitigation task will be briefly outlined.

  6. Review of the physics and response models for burnout of semiconductor devices. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Orvis, W.J.; Khanaka, G.H.; Yee, J.H.

    1984-12-01

    Physical mechanisms that cause semiconductor devices to fail from electrical overstress - particularly, EMP-induced electrical stress - are described in light of the current literature and the authors' own research. A major concern is the cause and effects of second breakdown phenomena in p-n junction devices. Models of failure thresholds are evaluated for their inherent errors and for their ability to represent the relevant physics. Finally, the response models that relate electromagnetic stress parameters to appropriate failure-threshold parameters are discussed.

  7. Gravity controlled anti-reverse rotation device

    Science.gov (United States)

    Dickinson, Robert J.; Wetherill, Todd M.

    1983-01-01

    A gravity assisted anti-reverse rotation device for preventing reverse rotation of pumps and the like. A horizontally mounted pawl is disposed to mesh with a fixed ratchet preventing reverse rotation when the pawl is advanced into intercourse with the ratchet by a vertically mounted lever having a lumped mass. Gravitation action on the lumped mass urges the pawl into mesh with the ratchet, while centrifugal force on the lumped mass during forward, allowed rotation retracts the pawl away from the ratchet.

  8. Wheelchair-mounted robotic arm to hold and move a communication device - final design.

    Science.gov (United States)

    Barrett, Graham; Kurley, Kyle; Brauchie, Casey; Morton, Scott; Barrett, Steven

    2015-01-01

    At the 51st Rocky Mountain Bioengineering Symposium we presented a preliminary design for a robotic arm to assist an individual living within an assistive technology smart home. The individual controls much of their environment with a Dynavox Maestro communication device. However, the device obstructs the individual’s line of site when navigating about the smart home. A robotic arm was developed to move the communication device in and out of the user’s field of view as desired. The robotic arm is controlled by a conveniently mounted jelly switch. The jelly switch sends control signals to a four state (up, off, down, off) single-axis robotic arm interfaced to a DC motor by high power electronic relays. This paper describes the system, control circuitry, and multiple safety features. The arm will be delivered for use later in 2015.

  9. Use of UPFC device controlled by fuzzy logic controllers for decoupled power flow control

    Directory of Open Access Journals (Sweden)

    Ivković Sanja

    2014-01-01

    Full Text Available This paper investigates the possibility of decoupled active and reactive power flow control in a power system using a UPFC device controlled by fuzzy logic controllers. A Brief theoretical review of the operation principles and applications of UPFC devices and design principles of the fuzzy logic controller used are given. A Matlab/Simulink model of the system with UPFC, the fuzzy controller setup, and graphs of the results are presented. Conclusions are drawn regarding the possibility of using this system for decoupled control of the power flow in power systems based on analysis of these graphs.

  10. Smart Rehabilitation Devices: Part I – Force Tracking Control

    Science.gov (United States)

    Dong, Shufang; Lu, Ke-Qian; Sun, J. Q.; Rudolph, Katherine

    2008-01-01

    Resistance exercise has been widely reported to have positive rehabilitation effects for patients with neuromuscular and orthopaedic conditions. This article presents prototypes of smart variable resistance exercise devices using magneto-rheological fluid dampers. An intelligent supervisory control for regulating the resistive force or torque of the device is developed, and is validated both numerically and experimentally. The device provides both isometric and isokinetic strength training for the human joints including knee, elbow, hip, and ankle. PMID:18504509

  11. digital control of external devices through the parallel port

    African Journals Online (AJOL)

    2012-11-03

    Nov 3, 2012 ... Abstract. In this paper we carry out the digital control of external devices using the parallel port of a computer. The PC parallel port adapter that is specifically designed to attach printers has been found to be useful as a general input/output port for any device or application that matches its input/output ...

  12. Wearable Device Control Platform Technology for Network Application Development

    Directory of Open Access Journals (Sweden)

    Heejung Kim

    2016-01-01

    Full Text Available Application development platform is the most important environment in IT industry. There are a variety of platforms. Although the native development enables application to optimize, various languages and software development kits need to be acquired according to the device. The coexistence of smart devices and platforms has rendered the native development approach time and cost consuming. Cross-platform development emerged as a response to these issues. These platforms generate applications for multiple devices based on web languages. Nevertheless, development requires additional implementation based on a native language because of the coverage and functions of supported application programming interfaces (APIs. Wearable devices have recently attracted considerable attention. These devices only support Bluetooth-based interdevice communication, thereby making communication and device control impossible beyond a certain range. We propose Network Application Agent (NetApp-Agent in order to overcome issues. NetApp-Agent based on the Cordova is a wearable device control platform for the development of network applications, controls input/output functions of smartphones and wearable/IoT through the Cordova and Native API, and enables device control and information exchange by external users by offering a self-defined API. We confirmed the efficiency of the proposed platform through experiments and a qualitative assessment of its implementation.

  13. TTC Interface Module for ATLAS Read-Out Electronics Final production version based on Xilinx FPGA devices

    CERN Document Server

    Butterworth, J; Postranecky, M; Warren, M R M; 10th Workshop on Electronics for LHC and Future Experiments

    2004-01-01

    The functionality and the details of firmware, software and hardware of the Xilinx FPGA-based production version of the ATLAS-SCT TTC Interface Module ( TIM ) are described. The TIM interfaces to the ATLAS Level-1 Trigger, using the LHC-standard TTC ( Timing, Trigger and Control ) system. Twelve prototype TIM modules have been built and used since 2001, based around ten AMD/Lattice CPLD devices. Final production modules, based on two Xilinx FPGAs, are all being built this year. The details of the hardware and firmware transition from CPLD to FPGA version are described, including the use of new software tools.

  14. Performance of Personal Workspace Controls Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Rubinstein, Francis; Kiliccote, Sila; Loffeld, John; Pettler,Pete; Snook, Joel

    2004-12-01

    One of the key deliverables for the DOE-funded controls research at LBNL for FY04 was the development of a prototype Personal Workspace Control system. The successful development of this system is a critical milestone for the LBNL Lighting Controls Research effort because this system demonstrates how IBECS can add value to today's Task Ambient lighting systems. LBNL has argued that by providing both the occupant and the facilities manager with the ability to precisely control the operation of overhead lighting and all task lighting in a coordinated manner, that task ambient lighting can optimize energy performance and occupant comfort simultaneously [Reference Task Ambient Foundation Document]. The Personal Workspace Control system is the application of IBECS to this important lighting problem. This report discusses the development of the Personal Workspace Control to date including descriptions of the different fixture types that have been converted to IBECS operation and a detailed description of the operation of PWC Scene Controller, which provides the end user with precise control of his task ambient lighting system. The objective, from the Annual Plan, is to demonstrate improvements in efficiency, lighting quality and occupant comfort realized using Personal Workspace Controls (PWC) designed to optimize the delivery of lighting to the individual's workstation regardless of which task-ambient lighting solution is chosen. The PWC will be capable of controlling floor-mounted, desk lamps, furniture-mounted and overhead lighting fixtures from a personal computer and handheld remote. The PWC will use an environmental sensor to automatically monitor illuminance, temperature and occupancy and to appropriately modulate ambient lighting according to daylight availability and to switch off task lighting according to local occupancy. [Adding occupancy control to the system would blunt the historical criticism of occupant-controlled lighting - the tendency of the

  15. Broadband Wireless Data Acquisition and Control Device Project

    Data.gov (United States)

    National Aeronautics and Space Administration — Mobitrum is proposing to develop a broadband wireless device for real-time data acquisition and monitoring applicable to the field instrumentation and control...

  16. Optically controlled multiple switching operations of DNA biopolymer devices

    Science.gov (United States)

    Hung, Chao-You; Tu, Waan-Ting; Lin, Yi-Tzu; Fruk, Ljiljana; Hung, Yu-Chueh

    2015-12-01

    We present optically tunable operations of deoxyribonucleic acid (DNA) biopolymer devices, where a single high-resistance state, write-once read-many-times memory state, write-read-erase memory state, and single low-resistance state can be achieved by controlling UV irradiation time. The device is a simple sandwich structure with a spin-coated DNA biopolymer layer sandwiched by two electrodes. Upon irradiation, the electrical properties of the device are adjusted owing to a phototriggered synthesis of silver nanoparticles in DNA biopolymer, giving rise to multiple switching scenarios. This technique, distinct from the strategy of doping of pre-formed nanoparticles, enables a post-film fabrication process for achieving optically controlled memory device operations, which provides a more versatile platform to fabricate organic memory and optoelectronic devices.

  17. New Multiphase Matrix Converter Based Device for Power Flow Control

    Directory of Open Access Journals (Sweden)

    Jerzy Szczepanik

    2013-12-01

    Full Text Available The article presents the concept of new matrix converter (MC based device working as a phase shifting control device in a power system. The multiphase MC is working under an innovative control algorithm specially dedicated to the proposed application. The work presents the results of the simulation of the MC work in this application as well as the analysis of the MC properties.

  18. Heterogeneous regional signal control : final report.

    Science.gov (United States)

    2017-03-12

    The goal of this project is to develop a comprehensive framework with a set of models to improve multi-modal traffic signal control, by incorporating advanced floating sensor data (e.g. GPS data, etc.) and traditional fixed sensor data (e.g. loop det...

  19. NREL Topic 1 Final Report: Cohesive Application of Standards-Based Connected Devices to Enable Clean Energy Technologies

    Energy Technology Data Exchange (ETDEWEB)

    Hudgins, Andrew P [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Sparn, Bethany F [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Jin, Xin [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Seal, Brian [Electric Power Research Institute (EPRI)

    2018-02-21

    This document is the final report of a two-year development, test, and demonstration project entitled 'Cohesive Application of Standards-Based Connected Devices to Enable Clean Energy Technologies.' The project was part of the National Renewable Energy Laboratory's (NREL) Integrated Network Test-bed for Energy Grid Research and Technology (INTEGRATE) initiative. The Electric Power Research Institute (EPRI) and a team of partners were selected by NREL to carry out a project to develop and test how smart, connected consumer devices can act to enable the use of more clean energy technologies on the electric power grid. The project team includes a set of leading companies that produce key products in relation to achieving this vision: thermostats, water heaters, pool pumps, solar inverters, electric vehicle supply equipment, and battery storage systems. A key requirement of the project was open access at the device level - a feature seen as foundational to achieving a future of widespread distributed generation and storage. The internal intelligence, standard functionality and communication interfaces utilized in this project result in the ability to integrate devices at any level, to work collectively at the level of the home/business, microgrid, community, distribution circuit or other. Collectively, the set of products serve as a platform on which a wide range of control strategies may be developed and deployed.

  20. Controllable proximity effect in superconducting hybrid devices

    NARCIS (Netherlands)

    Bakurskiy, S.V.

    2015-01-01

    This thesis is devoted to the study of controllable proximity effects in superconductors, both in terms of fundamental aspects and applications. As a part of this thesis theoretical description was suggested for a number of structures with superconducting electrodes and multiple interlayers. These

  1. 77 FR 28455 - National Standards for Traffic Control Devices; the Manual on Uniform Traffic Control Devices for...

    Science.gov (United States)

    2012-05-14

    ... environmental risk to health or safety that might disproportionately affect children. Executive Order 12630... all streets, highways, bikeways, and private roads open to public travel. The purpose of this final... devices on all roads open to public travel pursuant to 23 U.S.C. 109(d), 114(a), 217, 315, and 402(a). In...

  2. Nitrogen control of chloroplast differentiation. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Schmidt, G.W.

    1998-05-01

    This project was directed toward understanding at the physiological, biochemical and molecular levels of how photosynthetic organisms adapt to long-term nitrogen-deficiency conditions is quite incomplete even though limitation of this nutrient is the most commonly restricts plant growth and development. For our work on this problem, the unicellular green alga, Chlamydomonas reinhardtii, was grown in continuous cultures in which steady-state levels of nitrogen can be precisely controlled. N-limited cells exhibit the classical symptoms of deficiency of this nutrient, chlorosis and slow growth rates, and respond to nitrogen provision by rapid greening and chloroplast differentiation. We have addressed three aspects of this problem: (1) the regulation of pigment synthesis; (2) control of expression of nuclear genes encoding photosynthetic proteins; (3) changes in metabolic and electron transport pathways that enable sustained CO{sub 2} fixation even though they cannot be readily converted into amino and nucleic acids. For the last, principle components are: (a) enhanced mitochondrial respiratory activity intimately associated with photosynthates, and (b) the occurrence in thylakoids of a supplemental electron transport pathway that facilitates reduction of the plastoquinone pool. Together, these distinguishing features of N-limited cells are likely to enable cell survival, especially under conditions of high irradiance stress.

  3. The final design of the ATLAS Trigger/DAQ Readout-Buffer Input (ROBIN) Device

    CERN Document Server

    Kugel, A; Müller, M; Yu, M; Krause, E; Gorini, B; Joos, M; Petersen, J; Stancu, S; Green, B; Misiejuk, A; Kieft, G; Van Wasen, J; 10th Workshop on Electronics for LHC and Future Experiments

    2004-01-01

    The ATLAS readout subsystem (ROS) is the main interface between 1600 detector front-end readout links (ROL) and the high level (HLT) trigger farms. Its core device, the readout-buffer input (ROBIN), accepts event data on 3 readout links (ROLs) with a maximum rate of 100 kHz and a bandwidth of up to 160\\,MB/s per link. Incoming event data is temporarily buffered and delivered via PCI or Gigabit Ethernet on request. Two devices, a XILINX XC2V2000 FPGA and an IBM PowerPC 440, are present, implementing the ROBIN's functionality. Furthermore one 64 MB SDRAM event data buffer is available per ROL. The device supports the ATLAS baseline implementation, which foresees the PCI bus as the main communication path inside the ROS, as well as an optional data path using Gigabit Ethernet to increase scalability when needed. The paper presents the final design of the ATLAS ROBIN. Measurement results, obtained with a prototype device in PCI bus and Gigabit Ethernet setups, show the usability and approve the design choices.

  4. The Physiologic Effects of Multiple Simultaneous Electronic Control Device Discharges

    Science.gov (United States)

    Dawes, Donald M.; Ho, Jeffrey D.; Reardon, Robert F.; Sweeney, James D.; Miner, James R.

    2010-01-01

    Objectives: Law enforcement and military personnel use electronic control devices to control non-compliant and actively resistive subjects. The TASER® Shockwave is a new electronic control device designed specifically as an area denial device capable of delivering multiple simultaneous discharges. This is the first study to examine the effects of multiple simultaneous device discharges in humans. Methods: Volunteers were exposed to multiple (two to three), simultaneous 5-second discharges from the Shockwave device to the chest, back, chest to abdomen, or thighs. Blood was analyzed before and after discharge for pH, lactate, potassium, creatine kinase (CK), and troponin. Continuous spirometry was performed before, during, and after the discharge. In addition, electrocardiograms (ECGs) before and after discharge were recorded, and echocardiography was used to determine the rhythm during discharge. Results: Small elevations of lactate occurred. Moderate increases in CK at 24 hours occurred and appeared to be related to the number of simultaneous discharges. There was a trend to a decrease in minute ventilation in the volunteers exposed to two simultaneous discharges, but it did not reach statistical significance. ECG changes only reflected an increase in vagal tone, and there was no evidence of capture by echocardiography. Five-second, simultaneous, multiple exposures to the TASER Shockwave device were reasonably tolerated by our human volunteers. Conclusion: Our study suggests that this device may have a reasonable risk/benefit ratio when used to protect an area from a threat. PMID:20411076

  5. Virtual Machine Language Controls Remote Devices

    Science.gov (United States)

    2014-01-01

    Kennedy Space Center worked with Blue Sun Enterprises, based in Boulder, Colorado, to enhance the company's virtual machine language (VML) to control the instruments on the Regolith and Environment Science and Oxygen and Lunar Volatiles Extraction mission. Now the NASA-improved VML is available for crewed and uncrewed spacecraft, and has potential applications on remote systems such as weather balloons, unmanned aerial vehicles, and submarines.

  6. Precision control of biogas plants. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Moeller, H.B.; Nielsen, Anders M.; Ward, A.J.

    2009-10-15

    The objective of the project has been to improve design and process stability in biogas plants. The results can be divided within the following main categories: 1) Pre-treatment, serial coupling of digesters and post digestion 2) Process inhibition 3) Process control Ad 1) This work has shown that extreme thermophilic pre-treatment of cattle manure and pig manure mixed with silage has a considerable effect on methane yield in a subsequent methanogenic reactor. Ad 2) The effect of ammonia inhibition was studied in a series of continuously stirred tank reactors co-digesting pig manure (40%) with the addition of solid fractions (60%) and increasing concentrations of ammonia caused by addition of NH{sub 4}Cl pulses. Ad 3) Near infrared spectroscopy (NIRS) was used to predict liquid phase volatile fatty acid (VFA) concentrations in three experiments treating three different materials: pig slurry with maize silage, chicken manure and cattle slurry.

  7. Development and control of a magnetorheological haptic device for robot assisted surgery.

    Science.gov (United States)

    Shokrollahi, Elnaz; Goldenberg, Andrew A; Drake, James M; Eastwood, Kyle W; Kang, Matthew

    2017-07-01

    A prototype magnetorheological (MR) fluid-based actuator has been designed for tele-robotic surgical applications. This device is capable of generating forces up to 47 N, with input currents ranging from 0 to 1.5 A. We begin by outlining the physical design of the device, and then discuss a novel nonlinear model of the device's behavior. The model was developed using the Hammerstein-Wiener (H-W) nonlinear black-box technique and is intended to accurately capture the hysteresis behavior of the MR-fluid. Several experiments were conducted on the device to collect estimation and validation datasets to construct the model and assess its performance. Different estimating functions were used to construct the model, and their effectiveness is assessed based on goodness-of-fit and final-prediction-error measurements. A sigmoid network was found to have a goodness-of-fit of 95%. The model estimate was then used to tune a PID controller. Two control schemes were proposed to eliminate the hysteresis behavior present in the MR fluid device. One method uses a traditional force feedback control loop and the other is based on measuring the magnetic field using a Hall-effect sensor embedded within the device. The Hall-effect sensor scheme was found to be superior in terms of cost, simplicity and real-time control performance compared to the force control strategy.

  8. Gastroenterology-Urology Devices; Manual Gastroenterology-Urology Surgical Instruments and Accessories. Final rule; technical amendment.

    Science.gov (United States)

    2017-03-01

    The Food and Drug Administration (FDA) is amending the identification of manual gastroenterology-urology surgical instruments and accessories to reflect that the device does not include specialized surgical instrumentation for use with urogyencologic surgical mesh specifically intended for use as an aid in the insertion, placement, fixation, or anchoring of surgical mesh during urogynecologic procedures ("specialized surgical instrumentation for use with urogynecologic surgical mesh"). These amendments are being made to reflect changes made in the recently issued final reclassification order for specialized surgical instrumentation for use with urogynecologic surgical mesh.

  9. Advanced Energy Harvesting Control Schemes for Marine Renewable Energy Devices

    Energy Technology Data Exchange (ETDEWEB)

    McEntee, Jarlath [Ocean Renewable Power Company, Portland, ME (United States); Polagye, Brian [Ocean Renewable Power Company, Portland, ME (United States); Fabien, Brian [Ocean Renewable Power Company, Portland, ME (United States); Thomson, Jim [Ocean Renewable Power Company, Portland, ME (United States); Kilcher, Levi [Ocean Renewable Power Company, Portland, ME (United States); Marnagh, Cian [Ocean Renewable Power Company, Portland, ME (United States); Donegan, James [Ocean Renewable Power Company, Portland, ME (United States)

    2016-03-31

    dominated by long time scales. Following final system tests, the RivGen® device was submerged and each evaluated controller was tested across a range of gain/set point values and filter configurations for a minimum of 5 minutes, with longer runs attempted for well-performing cases. In addition to testing controllers during the 2015 deployment season, LGL Alaska Research Associates Inc. (LGL) performed a fish monitoring study in compliance with Alaska Department of Fish and Game fisheries habitat permit for the project. During the season, LGL reviewed 10% of 179 one-hour blocks of footage (6 minutes on the hour) and documented a total of over 1200 fish in the vicinity of the RivGen® device, including over 800 salmon smolt and over 350 adult salmon. No evidence of adverse effects including passage delay by upstream migrating salmon was noted. This is an important result for future deployments and has a direct impact on commercial system designs.

  10. Growth control of sessile microbubbles in PDMS devices

    CERN Document Server

    Volk, Andreas; Kähler, Christian J; Hilgenfeldt, Sascha; Marin, Alvaro

    2015-01-01

    In a microfluidic environment, the presence of bubbles is often detrimental to the functionality of the device, leading to clogging or cavitation, but microbubbles can also be an indispensable asset in other applications such as microstreaming. In either case, it is crucial to understand and control the growth or shrinkage of these bodies of air, in particular in common soft-lithography devices based on polydimethylsiloxane (PDMS), which is highly permeable to gases. In this work, we study the gas transport into and out of a bubble positioned in a microfluidic device, taking into account the direct gas exchange through PDMS as well as the transport of gas through the liquid in the device. Hydrostatic pressure regulation allows for the quantitative control of growth, shrinkage, or the attainment of a stable equilibrium bubble size. We find that the vapor pressure of the liquid plays an important role for the balance of gas transport, accounting for variability in experimental conditions and suggesting addition...

  11. Experimental and simulated control of lift using trailing edge devices

    Science.gov (United States)

    Cooperman, A.; Blaylock, M.; van Dam, C. P.

    2014-12-01

    Two active aerodynamic load control (AALC) devices coupled with a control algorithm are shown to decrease the change in lift force experienced by an airfoil during a change in freestream velocity. Microtabs are small (1% chord) surfaces deployed perpendicular to an airfoil, while microjets are pneumatic jets with flow perpendicular to the surface of the airfoil near the trailing edge. Both devices are capable of producing a rapid change in an airfoil's lift coefficient. A control algorithm for microtabs has been tested in a wind tunnel using a modified S819 airfoil, and a microjet control algorithm has been simulated for a NACA 0012 airfoil using OVERFLOW. In both cases, the AALC devices have shown the ability to mitigate the changes in lift during a gust.

  12. Prototyping of concurrent control systems implemented in FPGA devices

    CERN Document Server

    Wiśniewski, Remigiusz

    2017-01-01

    This book focuses on prototyping aspects of concurrent control systems and their further implementation and partial reconfiguration in programmable devices. Further, it lays out a full prototyping flow for concurrent control systems. Based on a given primary specification, a system is described with an interpreted Petri net, which naturally reflects the concurrent and sequential relationships of the design. The book shows that, apart from the traditional option of static configuration of the entire system, the latest programmable devices (especially FPGAs) offer far more sophistication. Partial reconfiguration allows selected parts of the system to be replaced without having to reprogram the entire structure of the device. Approaches to dynamic and static partial reconfiguration of concurrent control systems are presented and described in detail.< The theoretical work is illustrated by examples drawn from various applications, with a milling machine and a traffic-light controller highlighted as representat...

  13. Chaos control and taming of turbulence in plasma devices

    DEFF Research Database (Denmark)

    Klinger, T.; Schröder, C.; Block, D.

    2001-01-01

    . Electric control fields are externally applied to the plasma device and the chaotic or turbulent state is stabilized by only weak perturbations of the plasma equilibrium. The success of this approach is demonstrated in both experiment and numerical simulation and the actual effect of the applied control......Chaos and turbulence are often considered as troublesome features of plasma devices. In the general framework of nonlinear dynamical systems, a number of strategies have been developed to achieve active control over complex temporal or spatio-temporal behavior. Many of these techniques apply...

  14. Medical Devices; Immunology and Microbiology Devices; Classification of the Mass Spectrometer System for Clinical Use for the Identification of Microorganisms. Final order.

    Science.gov (United States)

    2017-10-24

    The Food and Drug Administration (FDA or we) is classifying the mass spectrometer system for clinical use for the identification of microorganisms into class II (special controls). The special controls that apply to the device type are identified in this order and will be part of the codified language for the mass pectrometer system for clinical use for the identification of microorganisms' classification. We are taking this action because we have determined that classifying the device into class II (special controls) will provide a reasonable assurance of safety and effectiveness of the device. We believe this action will also enhance patients' access to beneficial innovative devices, in part by reducing regulatory burdens.

  15. Medical Devices; Immunology and Microbiology Devices; Classification of the Automated Image Assessment System for Microbial Colonies on Solid Culture Media. Final order.

    Science.gov (United States)

    2017-10-16

    The Food and Drug Administration (FDA or we) is classifying the automated image assessment system for microbial colonies on solid culture media into class II (special controls). The special controls that apply to the device type are identified in this order and will be part of the codified language for the automated image assessment system for microbial colonies on solid culture media's classification. We are taking this action because we have determined that classifying the device into class II (special controls) will provide a reasonable assurance of safety and effectiveness of the device. We believe this action will also enhance patients' access to beneficial innovative devices, in part by reducing regulatory burdens.

  16. Implementation of Adaptive Digital Controllers on Programmable Logic Devices

    Science.gov (United States)

    Gwaltney, David A.; King, Kenneth D.; Smith, Keary J.; Monenegro, Justino (Technical Monitor)

    2002-01-01

    Much has been made of the capabilities of FPGA's (Field Programmable Gate Arrays) in the hardware implementation of fast digital signal processing. Such capability also makes an FPGA a suitable platform for the digital implementation of closed loop controllers. Other researchers have implemented a variety of closed-loop digital controllers on FPGA's. Some of these controllers include the widely used proportional-integral-derivative (PID) controller, state space controllers, neural network and fuzzy logic based controllers. There are myriad advantages to utilizing an FPGA for discrete-time control functions which include the capability for reconfiguration when SRAM-based FPGA's are employed, fast parallel implementation of multiple control loops and implementations that can meet space level radiation tolerance requirements in a compact form-factor. Generally, a software implementation on a DSP (Digital Signal Processor) or microcontroller is used to implement digital controllers. At Marshall Space Flight Center, the Control Electronics Group has been studying adaptive discrete-time control of motor driven actuator systems using digital signal processor (DSP) devices. While small form factor, commercial DSP devices are now available with event capture, data conversion, pulse width modulated (PWM) outputs and communication peripherals, these devices are not currently available in designs and packages which meet space level radiation requirements. In general, very few DSP devices are produced that are designed to meet any level of radiation tolerance or hardness. The goal of this effort is to create a fully digital, flight ready controller design that utilizes an FPGA for implementation of signal conditioning for control feedback signals, generation of commands to the controlled system, and hardware insertion of adaptive control algorithm approaches. An alternative is required for compact implementation of such functionality to withstand the harsh environment

  17. Synthetic feedback control using an RNAi-based gene-regulatory device.

    Science.gov (United States)

    Bloom, Ryan J; Winkler, Sally M; Smolke, Christina D

    2015-01-01

    Homeostasis within mammalian cells is achieved through complex molecular networks that can respond to changes within the cell or the environment and regulate the expression of the appropriate genes in response. The development of biological components that can respond to changes in the cellular environment and interface with endogenous molecules would enable more sophisticated genetic circuits and greatly advance our cellular engineering capabilities. Here we describe a platform that combines a ligand-responsive ribozyme switch and synthetic miRNA regulators to create an OFF genetic control device based on RNA interference (RNAi). We developed a mathematical model to highlight important design parameters in programming the quantitative performance of RNAi-based OFF control devices. By modifying the ribozyme switch integrated into the system, we demonstrated RNAi-based OFF control devices that respond to small molecule and protein ligands, including the oncogenic protein E2F1. We utilized the OFF control device platform to build a negative feedback control system that acts as a proportional controller and maintains target intracellular protein levels in response to increases in transcription rate. Our work describes a novel genetic device that increases the level of silencing from a miRNA in the presence of a ligand of interest, effectively creating an RNAi-based OFF control device. The OFF switch platform has the flexibility to be used to respond to both small molecule and protein ligands. Finally, the RNAi-based OFF switch can be used to implement a negative feedback control system, which maintains target protein levels around a set point level. The described RNAi-based OFF control device presents a powerful tool that will enable researchers to engineer homeostasis in mammalian cells.

  18. Cardiovascular devices; reclassification of nonroller-type cardiopulmonary bypass blood pumps for cardiopulmonary and circulatory bypass; effective date of requirement for premarket approval for nonroller-type cardiopulmonary bypass blood pumps for temporary ventricular support. Final order.

    Science.gov (United States)

    2015-06-08

    The Food and Drug Administration (FDA) is issuing a final order to reclassify nonroller-type cardiopulmonary bypass blood pump (NRP) devices for cardiopulmonary and circulatory bypass, a preamendments class III device, into class II (special controls), and to require the filing of a premarket approval application (PMA) for NRP devices for temporary ventricular support. FDA is also revising the title and identification of the regulation for NRP devices in this order.

  19. Flow control using audio tones in resonant microfluidic networks: towards cell-phone controlled lab-on-a-chip devices.

    Science.gov (United States)

    Phillips, Reid H; Jain, Rahil; Browning, Yoni; Shah, Rachana; Kauffman, Peter; Dinh, Doan; Lutz, Barry R

    2016-08-16

    Fluid control remains a challenge in development of portable lab-on-a-chip devices. Here, we show that microfluidic networks driven by single-frequency audio tones create resonant oscillating flow that is predicted by equivalent electrical circuit models. We fabricated microfluidic devices with fluidic resistors (R), inductors (L), and capacitors (C) to create RLC networks with band-pass resonance in the audible frequency range available on portable audio devices. Microfluidic devices were fabricated from laser-cut adhesive plastic, and a "buzzer" was glued to a diaphragm (capacitor) to integrate the actuator on the device. The AC flowrate magnitude was measured by imaging oscillation of bead tracers to allow direct comparison to the RLC circuit model across the frequency range. We present a systematic build-up from single-channel systems to multi-channel (3-channel) networks, and show that RLC circuit models predict complex frequency-dependent interactions within multi-channel networks. Finally, we show that adding flow rectifying valves to the network creates pumps that can be driven by amplified and non-amplified audio tones from common audio devices (iPod and iPhone). This work shows that RLC circuit models predict resonant flow responses in multi-channel fluidic networks as a step towards microfluidic devices controlled by audio tones.

  20. Universal Cloud Controller (UCC), a Cloud-centred system using personal mobile devices to control public devices

    OpenAIRE

    Thanh Tam, Tran

    2016-01-01

    We engage different working environments on a daily basis, including private and public environments. When we move from one to another constantly, the data also need to be transferred, and while the private environment is convenient, working with public devices creates the irritation of authentication. This dissertation proposes Universal Cloud Controller (UCC), a multi-components system that improves user’s experience when exchange data from personal to public device. The main functions of t...

  1. Gas flow control device for internal combustion engines

    Energy Technology Data Exchange (ETDEWEB)

    Matesic, A.; Castella, J.P.

    1996-08-29

    A gas flow control device for internal combustion engines, consisting of a single or double linearly movable member for controlling the flow rate of air in an intake duct, followed by a throttling mechanism for varying the cross-section of the duct. Both these devices may be common to all cylinders or provided plurally. Said including petrol engines or unsupercharged or turbocharged diesel engines, but is particularly suitable for four-stroke fuel ignition engines, i.e. those without a carburettor. (author)

  2. A Multiposture Locomotor Training Device with Force-Field Control

    Directory of Open Access Journals (Sweden)

    Jianfeng Sui

    2014-11-01

    Full Text Available This paper introduces a multiposture locomotor training device (MPLTD with a closed-loop control scheme based on joint angle feedback, which is able to overcome various difficulties resulting from mechanical vibration and the weight of trainer to achieve higher accuracy trajectory. By introducing the force-field control scheme used in the closed-loop control, the device can obtain the active-constrained mode including the passive one. The MPLTD is mainly composed of three systems: posture adjusting and weight support system, lower limb exoskeleton system, and control system, of which the lower limb exoskeleton system mainly includes the indifferent equilibrium mechanism with two degrees of freedom (DOF and the driving torque is calculated by the Lagrangian function. In addition, a series of experiments, the weight support and the trajectory accuracy experiment, demonstrate a good performance of mechanical structure and the closed-loop control.

  3. 78 FR 36132 - National Standards for Traffic Control Devices; Manual on Uniform Traffic Control Devices for...

    Science.gov (United States)

    2013-06-17

    ... and pop-ups as well as smart search options. The FHWA realizes more and more users are likely to use... from a number of electronic devices including computers, tablets, and smart phones. Enhancing search... electronic version. The commenters who preferred the electronic version cited the ability to search quickly...

  4. Channel Access and Power Control for Mobile Crowdsourcing in Device-to-Device Underlaid Cellular Networks

    Directory of Open Access Journals (Sweden)

    Yue Ma

    2018-01-01

    Full Text Available With the access of a myriad of smart handheld devices in cellular networks, mobile crowdsourcing becomes increasingly popular, which can leverage omnipresent mobile devices to promote the complicated crowdsourcing tasks. Device-to-device (D2D communication is highly desired in mobile crowdsourcing when cellular communications are costly. The D2D cellular network is more preferable for mobile crowdsourcing than conventional cellular network. Therefore, this paper addresses the channel access and power control problem in the D2D underlaid cellular networks. We propose a novel semidistributed network-assisted power and a channel access control scheme for D2D user equipment (DUE pieces. It can control the interference from DUE pieces to the cellular user accurately and has low information feedback overhead. For the proposed scheme, the stochastic geometry tool is employed and analytic expressions are derived for the coverage probabilities of both the cellular link and D2D links. We analyze the impact of key system parameters on the proposed scheme. The Pareto optimal access threshold maximizing the total area spectral efficiency is obtained. Unlike the existing works, the performances of the cellular link and D2D links are both considered. Simulation results show that the proposed method can improve the total area spectral efficiency significantly compared to existing schemes.

  5. The Physiologic Effects of Multiple Simultaneous Electronic Control Device Discharges

    Directory of Open Access Journals (Sweden)

    Dawes, Donald M

    2010-02-01

    Full Text Available Objectives: Law enforcement and military personnel use electronic control devices to control non-compliant and actively resistive subjects. The TASER® Shockwave is a new electronic control device designed specifically as an area denial device capable of delivering multiple simultaneous discharges. This is the first study to examine the effects of multiple simultaneous device discharges in humans.Methods: Volunteers were exposed to multiple (two to three, simultaneous 5-second discharges from the Shockwave device to the chest, back, chest to abdomen, or thighs. Blood was analyzed before and after discharge for pH, lactate, potassium, creatine kinase (CK, and troponin. Continuous spirometry was performed before, during, and after the discharge. In addition, electrocardiograms (ECGs before and after discharge were recorded, and echocardiography was used to determine the rhythm during discharge.Results: Small elevations of lactate occurred. Moderate increases in CK at 24 hours occurred and appeared to be related to the number of simultaneous discharges. There was a trend to a decrease in minute ventilation in the volunteers exposed to two simultaneous discharges, but it did not reach statistical significance. ECG changes only reflected an increase in vagal tone, and there was no evidence of capture by echocardiography. Five-second, simultaneous, multiple exposures to the TASER Shockwave device were reasonably tolerated by our human volunteers.Conclusion: Our study suggests that this device may have a reasonable risk/benefit ratio when used to protect an area from a threat. [West J Emerg Med. 2010; 11(1:49-56].

  6. Processing and modeling issues for thin-film solar cell devices. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Birkmire, R.W.; Phillips, J.E. [Univ. of Delaware, Newark, DE (United States). Institute of Energy Conversion

    1997-11-01

    During the third phase of the subcontract, IEC researchers have continued to provide the thin film PV community with greater depth of understanding and insight into a wide variety of issues including: the deposition and characterization of CuIn{sub 1-x}Ga{sub x}Se{sub 2}, a-Si, CdTe, CdS, and TCO thin films; the relationships between film and device properties; and the processing and analysis of thin film PV devices. This has been achieved through the systematic investigation of all aspects of film and device production and through the analysis and quantification of the reaction chemistries involved in thin film deposition. This methodology has led to controlled fabrications of 15% efficient CuIn{sub 1-x}Ga{sub x}Se{sub 2} solar cells over a wide range of Ga compositions, improved process control of the fabrication of 10% efficient a-Si solar cells, and reliable and generally applicable procedures for both contacting and doping films. Additional accomplishments are listed below.

  7. Computer Controlled Switching Device for Deep Brain Stimulation

    Directory of Open Access Journals (Sweden)

    J. Tauchmanová

    2007-01-01

    Full Text Available This paper has two goals. The practical part deals with the design of a computer controlled switching device for an external stimulator for deep brain stimulation. The switching device is used during investigations with functional magnetic resonance for controlling signals leading to the deep brain stimulation (DBS electrode in the patient's brain. The motivation for designing this device was improve measured data quality and to enable new types of experiments.The theoretical part reports on early attempts to approach the problem of modeling and localizing the neural response of the human brain as a system identification and estimation task. The parametric identification method and real fMRI data are used for modeling the hemodynamic response.The project is in cooperation with 1st Faculty of Medicine, Charles University in Prague and Na Homolce hospital in Prague.

  8. Multidisciplinary Analysis of a Microsystem Device for Thermal Control

    Science.gov (United States)

    Moran, Matthew E.

    2002-07-01

    A microelectromechanical (MEMS) device is under development that uses the Stirling cycle to provide cooling or heating directly to a thermally loaded surface. This MEMS cooler can be used strictly in the cooling mode, or switched between cooling and heating modes in milliseconds for precise temporal and spatial temperature control. Potential applications include cooling and thermal control of: microsystems, electronics, sensors, biomedical devices, and spacecraft components. A primary challenge for further development is the multidisciplinary analysis required to characterize and optimize its performance. This paper describes the first-order thermodynamic analysis performed on the MEMS cooler and the resulting ideal performance curves generated. The basis for additional coupled analyses such as fluid/gas dynamics, thermal, electrostatic, structural, dynamic, material, and processing is addressed. Scaling issues relevant to the device and the breakdown of continuum theory in the micro-domain is also examined.

  9. Three-Axis Attitude Control of Solar Sails Utilising Reflectivity Control Devices

    Science.gov (United States)

    Theodorou, Theodoros

    Solar sails are spacecraft that utilise the Solar Radiation Pressure, the force generated by impinging photons, to propel themselves. Conventional actuators are not suitable for controlling the attitude of solar sails therefore specific attitude control methods have been devised to tackle this. One of these methods is to change the centre of pressure with respect to the center of mass thus creating a torque. Reflectivity Control Devices (RCDs) have been proposed and successfully used to change the centre of pressure. Current methods that utilise RCDs have control authority over two axis only with no ability to control the torque about the normal of the sail surface. This thesis extends the state of the art and demonstrates 3-axis control by generating arbitrary torque vectors within a convex polyhedron. Two different RCD materials are considered, transmission and diffusion technologies both compatible with the proposed concept. A number of metrics have been developed which facilitate the comparison of different sail configurations. One of these metics is the sun map which is a graphic representation of the sun angles for which control authority is maintained. An iterative design process is presented which makes use of the metrics developed and aids in the design of a sail which meets the mission requirements and constraints. Moreover, the effects of different parameters on the performance of the proposed control concept are discussed. For example it is shown that by alternating the angle between the edge and middle RCDs the control authority increases. The concept's scalability has been investigated and a hybrid control scheme has been devised which makes use of both RCDs and reaction wheels. The RCDs are complemented by the reaction wheels to achieve higher slew rates while in turn the RCDs desaturate the reaction wheels. Finally, a number of simulations are conducted to verify the validity of the proposed concept.

  10. Assessment of the controllability of condensible emissions. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Shareef, G.S.; Waddell, J.T.

    1990-10-01

    The report gives results of a study to gain insights into the condensible emissions area from an air toxics perspective, with emphasis on controllability and chemical composition of these emissions. The study: compiled existing data on condensible emissions; determined the chemical composition of condensible emissions, where possible; identified source categories that are major emitters of condensibles; evaluated the effectiveness of various control devices in reducing condensible emissions; and evaluated how the performance of currently available control technologies can be improved to better control condensible emissions. Two data bases were developed: the Condensibles Data Base contains 43 emission source categories; the Specialized Condensibles Data Base focuses on the chemical composition of condensible emissions.

  11. Control system devices : architectures and supply channels overview.

    Energy Technology Data Exchange (ETDEWEB)

    Trent, Jason; Atkins, William Dee; Schwartz, Moses Daniel; Mulder, John C.

    2010-08-01

    This report describes a research project to examine the hardware used in automated control systems like those that control the electric grid. This report provides an overview of the vendors, architectures, and supply channels for a number of control system devices. The research itself represents an attempt to probe more deeply into the area of programmable logic controllers (PLCs) - the specialized digital computers that control individual processes within supervisory control and data acquisition (SCADA) systems. The report (1) provides an overview of control system networks and PLC architecture, (2) furnishes profiles for the top eight vendors in the PLC industry, (3) discusses the communications protocols used in different industries, and (4) analyzes the hardware used in several PLC devices. As part of the project, several PLCs were disassembled to identify constituent components. That information will direct the next step of the research, which will greatly increase our understanding of PLC security in both the hardware and software areas. Such an understanding is vital for discerning the potential national security impact of security flaws in these devices, as well as for developing proactive countermeasures.

  12. On the feasibility of device fingerprinting in industrial control systems

    NARCIS (Netherlands)

    Caselli, M.; Hadziosmanovic, D.; Zambon, Emmanuele; Kargl, Frank; Luiijf, Eric; Hartel, Pieter H.

    2013-01-01

    As Industrial Control Systems (ICS) and standard IT networks are becoming one heterogeneous entity, there has been an increasing effort in adjusting common security tools and methodologies to fit the industrial environment. Fingerprinting of industrial devices is still an unexplored research field.

  13. Advanced patient transfer assist device with intuitive interaction control.

    Science.gov (United States)

    Humphreys, Heather C; Choi, Young Mi; Book, Wayne J

    2017-10-24

    This research aims to improve patient transfers by developing a new type of advanced robotic assist device. It has multiple actuated degrees of freedom and a powered steerable base to maximize maneuverability around obstacles. An intuitive interface and control strategy allows the caregiver to simply push on the machine in the direction of desired patient motion. The control integrates measurements of both force and proximity to mitigate any potential large collision forces and provides operators information about obstacles with a form of haptic feedback. Electro-hydraulic pump controlled actuation provides high force density for the actuation. Nineteen participants performed tests to compare transfer operations (transferring a 250-lb mannequin between a wheelchair, chair, bed, and floor) and interaction control of a prototype device with a commercially available patient lift. The testing included a time study of the transfer operations and subjective rating of device performance. The results show that operators perform transfer tasks significantly faster and rate performance higher using the prototype patient transfer assist device than with a current market patient lift. With further development, features of the new patient lift can help facilitate patient transfers that are safer, easier, and more efficient for caregivers.

  14. Biopolymers in controlled release devices for agricultural applications.

    Science.gov (United States)

    The use of biopolymers such as starch for agricultural applications including controlled release devices is growing due the environmental benefits. Recently, concerns have grown about the worldwide spread of parasitic mites (Varroa destructor) that infect colonies of honey bees (Apis mellifera L.). ...

  15. Leap Motion Device Used to Control a Real Anthropomorphic Gripper

    Directory of Open Access Journals (Sweden)

    Ionel Staretu

    2016-06-01

    Full Text Available This paper presents for the first time the use of the Leap Motion device to control an anthropomorphic gripper with five fingers. First, a description of the Leap Motion device is presented, highlighting its main functional characteristics, followed by testing of its use for capturing the movements of a human hand's fingers in different configurations. Next, the HandCommander soft module and the Interface Controller application are described. The HandCommander is a software module created to facilitate interaction between a human hand and the GraspIT virtual environment, and the Interface Controller application is required to send motion data to the virtual environment and to test the communication protocol. For the test, a prototype of an anthropomorphic gripper with five fingers was made, including a proper hardware system of command and control, which is briefly presented in this paper. Following the creation of the prototype, the command system performance test was conducted under real conditions, evaluating the recognition efficiency of the objects to be gripped and the efficiency of the command and control strategies for the gripping process. The gripping test is exemplified by the gripping of an object, such as a screw spanner. It was found that the command system, both in terms of capturing human hand gestures with the Leap Motion device and effective object gripping, is operational. Suggestive figures are presented as examples.

  16. A Wii-controlled safety device for electric chainsaws

    Directory of Open Access Journals (Sweden)

    R. Gubiani

    2013-09-01

    Full Text Available Forestry continues to represent one of the most hazardous economic sectors of human activity, and historically, the operation of chainsaws has mainly been restricted to professional lumberjacks. In recent years, because of low cost, chainsaws have become popular among unprofessionals, e.g. for cutting firewood and trimming trees. Serious or lethal lesions due to the use of chainsaws or electric chainsaws are often observed by traumatologists or forensic pathologists. Such serious accidents often occur during occupational activities and are essentially due to kickback or uncorrected use of the tool, or when the operator falls down losing the control of the implement. A new device in order to stop a cutting chain was developed and adapted to an electric chainsaw. The device is based on a Wiimote controller (Nintendo™, including two accelerometers and two gyroscopes for detecting rotation and inclination. A Bluetooth wireless technology is used to transfer data to a portable computer. The data collected about linear and angular acceleration are filtered by an algorithm, based on the Euclid norm, capable to distinguishing between normal movements and dangerous chainsaw movements. The result show a good answer to device and when happen a dangerous situation an alarm signal is sent back to the implement in order to stop the cutting chain. The device show a correct behavior in tested dangerous situations and is envisaged to extend to combustion engine chainsaws, as well as to other portable equipment used in agriculture and forestry operations and for this objectives were patented.

  17. Inspection operation aid device and method for control rod drives and hydraulic control system

    Energy Technology Data Exchange (ETDEWEB)

    Shimizu, Shun-ichi; Yamamoto, Hiroki; Okuzumi, Naoaki; Ishisato, Shin-ichi

    1995-12-12

    The device of the present invention comprises an input/output device for inputting/outputting various data required for evaluation of integrity, a memorizing/storing device, an information processing device and a display device. Friction data as differential pressure signals of driving hydraulic pressures measured upon inspection/test operation of control rod drives and hydraulic pressure control system are taken into the input/output device. A result of processing for friction signal waveform pattern is calculated. The integrity and abnormality of the control rod drives and the hydraulic pressure system are evaluated using a causal relation between the result of the signal processing for obtained waveform patterns and the intelligence/knowledge of behaviors of the control rod devices and the hydraulic pressure control system thereby providing integrity data. Since the friction data can be calculated automatically by signal waveform pattern processing, there is no need to read the data manually by specialists who take part in the inspection and test. As a result, data on evaluation for integrity and abnormality of the control rod drives and the hydraulic pressure control system can be provided rapidly. (N.H.).

  18. Control device for controlling the fuel-air ratio of an internal combustion engine

    Energy Technology Data Exchange (ETDEWEB)

    Rado, W.G.

    1982-04-08

    The invention deals with a control device for controlling the fuel-air ratio of a combustion engine. The oxygen content in the exhaust gas is measured in certain time intervals thereby determining whether a pre-determined number of measurements shows the result ''lean'' or ''rich'', the control device adjusts the mixture according to the measured results if necessary.

  19. Self-Correcting HVAC Controls Project Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Fernandez, Nicholas; Brambley, Michael R.; Katipamula, Srinivas; Cho, Heejin; Goddard, James K.; Dinh, Liem H.

    2010-01-04

    This document represents the final project report for the Self-Correcting Heating, Ventilating and Air-Conditioning (HVAC) Controls Project jointly funded by Bonneville Power Administration (BPA) and the U.S. Department of Energy (DOE) Building Technologies Program (BTP). The project, initiated in October 2008, focused on exploratory initial development of self-correcting controls for selected HVAC components in air handlers. This report, along with the companion report documenting the algorithms developed, Self-Correcting HVAC Controls: Algorithms for Sensors and Dampers in Air-Handling Units (Fernandez et al. 2009), document the work performed and results of this project.

  20. A device for automatic photoelectric control of the analytical gap for emission spectrographs

    Science.gov (United States)

    Dietrich, John A.; Cooley, Elmo F.; Curry, Kenneth J.

    1977-01-01

    A photoelectric device has been built that automatically controls the analytical gap between electrodes during excitation period. The control device allows for precise control of the analytical gap during the arcing process of samples, resulting in better precision of analysis.

  1. Mechanism of controlled release kinetics from medical devices

    Directory of Open Access Journals (Sweden)

    A. Raval

    2010-06-01

    Full Text Available Utilization of biodegradable polymers for controlled drug delivery has gained immense attention in the pharmaceutical and medical device industry to administer various drugs, proteins and other bio-molecules both systematically and locally to cure several diseases. The efficacy and toxicity of this local therapeutics depends upon drug release kinetics, which will further decide drug deposition, distribution, and retention at the target site. Drug Eluting Stent (DES presently possesses clinical importance as an alternative to Coronary Artery Bypass Grafting due to the ease of the procedure and comparable safety and efficacy. Many models have been developed to describe the drug delivery from polymeric carriers based on the different mechanisms which control the release phenomenon from DES. Advanced characterization techniques facilitate an understanding of the complexities behind design and related drug release behavior of drug eluting stents, which aids in the development of improved future drug eluting systems. This review discusses different drug release mechanisms, engineering principles, mathematical models and current trends that are proposed for drug-polymer coated medical devices such as cardiovascular stents and different analytical methods currently utilized to probe diverse characteristics of drug eluting devices.

  2. Model predictive control approach for a CPAP-device

    Directory of Open Access Journals (Sweden)

    Scheel Mathias

    2017-09-01

    Full Text Available The obstructive sleep apnoea syndrome (OSAS is characterized by a collapse of the upper respiratory tract, resulting in a reduction of the blood oxygen- and an increase of the carbon dioxide (CO2 - concentration, which causes repeated sleep disruptions. The gold standard to treat the OSAS is the continuous positive airway pressure (CPAP therapy. The continuous pressure keeps the upper airway open and prevents the collapse of the upper respiratory tract and the pharynx. Most of the available CPAP-devices cannot maintain the pressure reference [1]. In this work a model predictive control approach is provided. This control approach has the possibility to include the patient’s breathing effort into the calculation of the control variable. Therefore a patient-individualized control strategy can be developed.

  3. Researching on Control Device of Prestressing Wire Reinforcement

    Science.gov (United States)

    Si, Jianhui; Guo, Yangbo; Liu, Maoshe

    2017-06-01

    This paper mainly introduces a device for controlling prestress and its related research methods, the advantage of this method is that the reinforcement process is easy to operate and control the prestress of wire rope accurately. The relationship between the stress and strain of the steel wire rope is monitored during the experiment, and the one - to - one relationship between the controllable position and the pretightening force of the steel wire rope is confirmed by the 5mm steel wire rope, and the results are analyzed theoretically by the measured elastic modulus. The results show that the method can effectively control the prestressing force, and the result provides a reference method for strengthening the concrete column with prestressed steel strand.

  4. Controlled closing on shunt reactor compensated transmission lines. Part 1: Closing control device development

    Energy Technology Data Exchange (ETDEWEB)

    Froehlich, K.; Hoelzl, C.; Stanek, M. [Univ. of Technology, Vienna (Austria); Carvalho, A.C.; Hofbauer, W.; Hoegg, P.; Avent, B.L.; Peelo, D.F.; Sawada, J.H.

    1997-04-01

    A control device for point-on-wave closing or auto-reclosing of shunt reactor compensated transmission lines for reduction of closing overvoltages is presented. The device is the first of its kind. It was put into field service successfully more than a year ago. Development aspects and basic investigations on the relevant transient switching phenomena are presented. The algorithm employed works independently of the shape of the voltage signal to be synchronized on by means of pattern recognition. Peculiarities of the hardware are high redundancy and a system to bypass the controller at any malfunction of the electronic circuits. The efficiency of the controller was verified by a combination of transient network analyzer tests and EMTP simulations showing the ability of the device to suppress overvoltages. This procedure is generally recommended for future application of control devices as a type test procedure.

  5. Preparation and investigation of controlled-release glipizide novel oral device with three-dimensional printing.

    Science.gov (United States)

    Li, Qijun; Wen, Haoyang; Jia, Danyang; Guan, Xiaoying; Pan, Hao; Yang, Yue; Yu, Shihui; Zhu, Zhihong; Xiang, Rongwu; Pan, Weisan

    2017-06-15

    The purpose of this study was to explore the feasibility of combining fused deposition modeling (FDM) 3D printing technology with hot melt extrusion (HME) to fabricate a novel controlled-release drug delivery device. Glipizide used in the treatment of diabetes was selected as model drug, and was successfully loaded into commercial polyvinyl alcohol (PVA) filaments by HME method. The drug-loaded filaments were printed through a dual-nozzle 3D printer, and finally formed a double-chamber device composed by a tablet embedded within a larger tablet (DuoTablet), each chamber contains different contents of glipizide. The drug-loaded 3D printed device was evaluated for drug release under in vitro dissolution condition, and we found the release profile fit Korsmeyer-Peppas release kinetics. With the double-chamber design, it is feasible to design either controlled drug release or delayed drug release behavior by reasonably arranging the concentration distribution of the drug in the device. The characteristics of the external layer performed main influence on the release profile of the internal compartment such as lag-time or rate of release. The results of this study suggest the potential of 3D printing to fabricate controlled-release drug delivery system containing multiple drug concentration distributions via hot melt extrusion method and specialized design configurations. Copyright © 2017 Elsevier B.V. All rights reserved.

  6. Medical Devices; Immunology and Microbiology Devices; Classification of the Device To Detect and Measure Non-Microbial Analyte(s) in Human Clinical Specimens To Aid in Assessment of Patients With Suspected Sepsis. Final order.

    Science.gov (United States)

    2017-10-24

    The Food and Drug Administration (FDA or we) is classifying the device to detect and measure non-microbial analyte(s) in human clinical specimens to aid in assessment of patients with suspected sepsis into class II (special controls). The special controls that apply to the device type are identified in this order and will be part of the codified language for the device to detect and measure non-microbial analyte(s) in human clinical specimens to aid in assessment of patients with suspected sepsis's classification. We are taking this action because we have determined that classifying the device into class II (special controls) will provide a reasonable assurance of safety and effectiveness of the device. We believe this action will also enhance patients' access to beneficial innovative devices, in part by reducing regulatory burdens.

  7. Medical Devices; Immunology and Microbiology Devices; Classification of the Nucleic Acid-Based Device for the Amplification, Detection, and Identification of Microbial Pathogens Directly From Whole Blood Specimens. Final order.

    Science.gov (United States)

    2017-10-16

    The Food and Drug Administration (FDA or we) is classifying the nucleic acid-based device for the amplification, detection, and identification of microbial pathogens directly from whole blood specimens into class II (special controls). The special controls that apply to the device type are identified in this order and will be part of the codified language for the nucleic acid-based device for the amplification, detection, and identification of microbial pathogens directly from whole blood specimens' classification. We are taking this action because we have determined that classifying the device into class II (special controls) will provide a reasonable assurance of safety and effectiveness of the device. We believe this action will also enhance patients' access to beneficial innovative devices, in part by reducing regulatory burdens.

  8. Closed Loop Control Compact Exercise Device for Use on MPCV

    Science.gov (United States)

    Sheehan, Chris; Funk, Justin; Funk, Nathan; Kutnick, Gilead; Humphreys, Brad; Bruinsma, Douwe; Perusek, Gail

    2016-01-01

    Long duration space travel to Mars or to an asteroid will expose astronauts to extended periods of reduced gravity. To combat spaceflight physiological deconditioning, astronauts will use resistive and aerobic exercise regimens for the duration of the space flight to minimize the loss of bone density, muscle mass and aerobic capacity that occurs during exposure to a reduced gravity environment. Unlike the International Space Station (ISS), the mass and volume available for an exercise device in the next generation of spacecraft is limited. Therefore, compact exercise device prototypes are being developed for human in the loop evaluations. The NASA Human Research Program (HRP) is managing Advanced Exercise Concepts (AEC) requirements development and candidate technology maturation for all exploration mission profiles from Multi-Purpose Crew Vehicle (MPCV) exploration missions (e.g., EM-2, up to 21 day) to Mars Transit (up to 1000 day) missions. Numerous technologies have been considered and evaluated against HRP-approved functional requirements and include flywheel, pneumatic and closed-loop microprocessor-controlled motor driven power plants. Motor driven technologies offer excellent torque density and load accuracy characteristics as well as the ability to create custom mechanical impedance (the dynamic relationship between force and velocity) and custom load versus position exercise algorithms. Further, closed-loop motor-driven technologies offer the ability to monitor exercise dose parameters and adapt to the needs of the crewmember for real time optimization of exercise prescriptions. A simple proportional-integral-derivative (PID) controller is demonstrated in a prototype motor driven exercise device with comparison to resistive static and dynamic load set points and aerobic work rate targets. The resistive load term in the algorithm includes a constant force component (Fcmg) as well as inertial component (Fima) and a discussion of system tuning is presented

  9. Technological Breakthroughs in Growth Control of Silicon Carbide for High Power Electronic Devices

    Science.gov (United States)

    Matsunami, Hiroyuki

    2004-10-01

    Technological breakthroughs in growth control of SiC are reviewed. Step-controlled epitaxy by using off-axis SiC {0001} substrates to grow high-quality epitaxial layer is explained in detail. The introduction of substrate off-angles brings step-flow growth, which easily makes polytype replication of SiC at rather low temperatures. Off-angle dependence, rate-determining processes, and temperature dependence of growth rate are discussed. Prediction, whether step-flow growth or two-dimensional nucleation does occur, is given as a function of off-angle, growth temperature, and growth rate. Optical and electrical properties of undoped epitaxial layers are characterized. Impurity doping during the growth is explained. Recent progresses in peripheral technologies for realization of power electronic devices, such as bulk growth, epitaxial growth, ion implantation, MOS interface, ohmic contacts, are introduced. Finally application to high-power electronic devices is briefly described.

  10. Final results of the US humanitarian device exemption study of the low-profile visualized intraluminal support (LVIS) device.

    Science.gov (United States)

    Fiorella, David; Arthur, Adam; Boulos, Alan; Diaz, Orlando; Jabbour, Pascal; Pride, Lee; Turk, Aquilla S; Woo, Henry H; Derdeyn, Colin; Millar, John; Clifton, Andrew

    2016-09-01

    The low-profile visualized intraluminal support (LVIS) device is a new, braided, intracranial microstent designed for stent-assisted coiling. To present the results of a single-arm, prospective, multicenter trial of the LVIS for treatment of wide-necked intracranial aneurysms. 31 patients with unruptured, wide-necked (neck ≥4 mm or dome:neck ratio ≤2) intracranial aneurysms were treated with the LVIS device and bare platinum coils at six US centers (investigational device exemption G110014). Clinical follow-up was conducted at 30 days and 6 months. Angiographic follow-up was performed at 6 months. The primary safety endpoint was any major stroke or death within 30 days or major ipsilateral stroke or neurological death within 6 months. 'Probable benefit' was defined as ≥90% angiographic occlusion at 6 months. An independent core laboratory adjudicated the angiographic results. An independent clinical events committee adjudicated the clinical endpoints. Average aneurysm size was 7.2 mm (SD 3.8) and average neck width was 4.6 mm (SD 1.8). 68% of patients had a dome:neck ratio ≤2. LVIS placement was technically successful in 29/31 patients (93.5%). No primary safety endpoints occurred during the study (0%). No patient had a higher modified Rankin Score at 6 months than at baseline. 26/28 (92.9%) treated aneurysms with 6-month angiographic follow-up demonstrated ≥90% angiographic occlusion. 21/28 (75%) were completely occluded at follow-up. The LVIS device facilitated the coil embolization of wide-necked intracranial aneurysms with high rates of technical success, an excellent safety profile, and very high rates of complete and near-complete occlusion at follow-up. NCT01541254. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/

  11. Virtual planning for vertical control using temporary anchorage devices

    Directory of Open Access Journals (Sweden)

    Mauricio Accorsi

    2015-01-01

    Full Text Available The new and innovative technologies are unprecedentedly improving the level of proficiency in orthodontics in the recent history of this area of expertise. The proliferation of advances, such as self-ligating systems, temporary anchorage devices, shape-memory wires, robotically wire bending, intraoral scanners, cone-beam computed tomography, bring the virtual planning, and confection of dental devices through CAD/CAM systems to the real world. In order to get efficiency and efficacy in orthodontics with these new technologies, we must understand the importance of systemically managed clinical information, medical, and dentistry history of the patients, including the images resources, which ensures the use of a communication that is assisted by the technology, with an interdisciplinary team so that the database is able to help and support the process of therapeutic decision-making. This paper presents the clinical case of a borderline patient for orthognathic surgery who had his final treatment planning supported by these new tools for three-dimensional diagnosis and virtual planning.

  12. Polymeric barrier membranes for device packaging, diffusive control and biocompatibility

    Energy Technology Data Exchange (ETDEWEB)

    Wasikiewicz, J.M.; Roohpour, N.; Paul, D. [IRC in Biomedical Materials, Queen Mary, University of London, London (United Kingdom); Grahn, M. [Centre for Academic Surgery, Queen Mary University of London, London (United Kingdom); Ateh, D. [IRC in Biomedical Materials, Queen Mary, University of London, London (United Kingdom); Barts and the London Queen Mary' s school of Medicine and Dentistry, Queen Mary University of London, London (United Kingdom); Rehman, I. [IRC in Biomedical Materials, Queen Mary, University of London, London (United Kingdom); Vadgama, P. [IRC in Biomedical Materials, Queen Mary, University of London, London (United Kingdom)], E-mail: p.vadgama@qmul.ac.uk

    2008-11-15

    Current state-of-the-art implantable micron feature electronic devices are capable of monitoring and stimulating functions in vivo. Within an EU Framework VI project a further step was taken in developing key microsystem technologies and communication methods that could bring intelligence directly to the human interface, in the form of reactive medical implants and ambulatory measurement systems. Information from these devices is planned to be transmitted out into the wider environment for remote processing. However, the packaging of such state-of-the-art devices to enhance tissue biocompatibility, and to protect conducting elements from in vivo corrosion during extended use, along with protecting the body from toxins leaching from implant components, remains a concern. Candidate polymeric barriers as hydration resistant and solute impermeable interfaces to mitigate such major problems of chronic implantation were investigated. Materials studied included silicone rubber, PVC, polyurethane, and diamond-like carbon (DLC). Polymer permeability to water solutes was marginally improved through incorporation of lipid into these structures. Surface biocompatibility was assessed on the basis of protein film deposition in vitro and by cell viability studies in tissue culture. Short-term toxicity was not observed for any of the tested materials, though there were substantial differences in hydration. Additionally, polypyrrole over active electrodes shows feasibility for controlled tissue interfacing whilst retaining electrical conductivity.

  13. Optimal control and quantum simulations in superconducting quantum devices

    Energy Technology Data Exchange (ETDEWEB)

    Egger, Daniel J.

    2014-10-31

    Quantum optimal control theory is the science of steering quantum systems. In this thesis we show how to overcome the obstacles in implementing optimal control for superconducting quantum bits, a promising candidate for the creation of a quantum computer. Building such a device will require the tools of optimal control. We develop pulse shapes to solve a frequency crowding problem and create controlled-Z gates. A methodology is developed for the optimisation towards a target non-unitary process. We show how to tune-up control pulses for a generic quantum system in an automated way using a combination of open- and closed-loop optimal control. This will help scaling of quantum technologies since algorithms can calibrate control pulses far more efficiently than humans. Additionally we show how circuit QED can be brought to the novel regime of multi-mode ultrastrong coupling using a left-handed transmission line coupled to a right-handed one. We then propose to use this system as an analogue quantum simulator for the Spin-Boson model to show how dissipation arises in quantum systems.

  14. Methods of measurement for semiconductor materials, process control, and devices

    Science.gov (United States)

    Bullis, W. M. (Editor)

    1972-01-01

    Activities directed toward the development of methods of measurement for semiconductor materials, process control, and devices are described. Topics investigated include: measurements of transistor delay time; application of the infrared response technique to the study of radiation-damaged, lithium-drifted silicon detectors; and identification of a condition that minimizes wire flexure and reduces the failure rate of wire bonds in transistors and integrated circuits under slow thermal cycling conditions. Supplementary data concerning staff, standards committee activities, technical services, and publications are included as appendixes.

  15. A High-Strength, Absorbable, Antibacterial Knotless Tissue Control Device for Fascial Closure

    OpenAIRE

    Nawrocki, Jesse G.; Nonnenmann, Heather; Mooney, Mark; Sutton, Nadia; Schmitz, Niels-Derrek

    2017-01-01

    Purpose of Review This review provides an overview of the STRATAFIX? SYMMETRIC PDS? Plus Knotless Tissue Control Device design and performance characteristics and highlights the device?s relevance for use in gynecological procedures. Various device testing was conducted on tensile strength, fixation tab mass comparison to conventional suture knot tower, initiation stitch strength, and wound holding strength to highlight the STRATAFIX? SYMMETRIC PDS? Plus Device?s key product attributes that m...

  16. Equilibria near asteroids for solar sails with reflection control devices

    Science.gov (United States)

    Gong, Shengping; Li, Junfeng

    2015-02-01

    Solar sails are well-suited for long-term, multiple-asteroid missions. The dynamics of solar sails near an asteroid have not yet been studied in detail. In this paper, out-of-plane artificial equilibria in a Sun-asteroid rotating frame and hovering points in a body-fixed rotating frame are studied (using a solar sail equipped with reflection control devices). First, the dynamics and the stability of out-of-plane artificial equilibria are studied as an elliptical restricted three body problem. Next, the body-fixed hovering problem is discussed as a two-body problem. Hovering flight is only possible for certain values of the latitude of the asteroid's orbit. In addition, the feasible range of latitudes is determined for each landmark on the asteroid's surface. The influence of the sail lightness number on the feasible range is also illustrated. Several special families of hovering points are discussed. These points include points above the equator and poles and points with an altitude equal to the radius of the synchronous orbit. In both of these types of problems, the solar sail (equipped with reflection control devices) can equilibrate over a large range of locations.

  17. 1st International Conference on Intelligent Communication, Control and Devices

    CERN Document Server

    Choudhury, Sushabhan

    2017-01-01

    The book presents high-quality research papers presented at the first international conference, ICICCD 2016, organised by the Department of Electronics, Instrumentation and Control Engineering of University of Petroleum and Energy Studies, Dehradun on 2nd and 3rd April, 2016. The book is broadly divided into three sections: Intelligent Communication, Intelligent Control and Intelligent Devices. The areas covered under these sections are wireless communication and radio technologies, optical communication, communication hardware evolution, machine-to-machine communication networks, routing techniques, network analytics, network applications and services, satellite and space communications, technologies for e-communication, wireless Ad-Hoc and sensor networks, communications and information security, signal processing for communications, communication software, microwave informatics, robotics and automation, optimization techniques and algorithms, intelligent transport, mechatronics system, guidance and navigat...

  18. Control and Data Analysis for Emittance Measuring Devices

    CERN Document Server

    Hoffmann, T

    2001-01-01

    Due to the wide range of heavy ion beam intensities and energies in the GSI linac and the associated transfer channel to the synchrotron, several different types of emittance measurement systems have been established. Many common devices such as slit/grid or dipole-sweep systems are integrated into the GSI control system. Other systems like the single shot pepper pot method using CCD-cameras or stand-alone slit/grid set-ups are connected to personal computers. An overview is given about the various systems and their software integration. Main interest is directed on the software development for emittance front-end control and data analysis such as evaluation algorithms or graphical presentation of the results. In addition, special features for improved usability of the software such as data export, project databases and automatic report generation will be presented. An outlook on a unified evaluation procedure for all different types of emittance measurement is given.

  19. Integrated Channel Selector for Directing Fluid Flow Using Thermoreversible Gelation Controlled by a Digital Mirror Device

    Directory of Open Access Journals (Sweden)

    Yoshitaka Shirasaki

    2013-01-01

    Full Text Available An integrated channel selector system employing thermoreversible gelation of a polymer was developed. Here, we show a system with 3×3 arrayed microchannels having nine crossing points. Infrared laser irradiation was used to form gel areas at several crossing points in arranging a flow path from the inlet to one of the nine outlets passing through certain junctions and channels. The multipoint irradiation by the infrared laser was realized using a personal-computer-controlled digital mirror device. The system was demonstrated to be able to direct flow to all nine outlets. Finally, we achieved to produce flexible paths for flowing particles including side trips.

  20. Active Thermal Control by Controlled Shoot-through of Power Devices

    DEFF Research Database (Denmark)

    Soldati, Alessandro; Concari, Carlo; Barater, Davide

    2017-01-01

    Active Thermal Control (ATC) consists in driving power switches in a less efficient way when low load conditions are present. The resulting wasted power is used to self-heat the device, reducing amplitude and occurrence of thermal cycles and hence improving the reliability. This paper presents a ...... a novel way to control losses, and hence temperature, of both positive- and negative-current devices in half-bridge topologies at various load conditions. The goal is achieved by means of a controlled shoot-through of the half-bridge leg....

  1. Method and apparatus for actively controlling a micro-scale flexural plate wave device

    Science.gov (United States)

    Dohner, Jeffrey L.

    2001-01-01

    An actively controlled flexural plate wave device provides a micro-scale pump. A method of actively controlling a flexural plate wave device produces traveling waves in the device by coordinating the interaction of a magnetic field with actively controlled currents. An actively-controlled flexural plate wave device can be placed in a fluid channel and adapted for use as a micro-scale fluid pump to cool or drive micro-scale systems, for example, micro-chips, micro-electrical-mechanical devices, micro-fluid circuits, or micro-scale chemical analysis devices.

  2. Microprocessor control of a ground water heat pump. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1980-01-01

    This project was a demonstration of the energy savings available to a small well-insulated facility when a properly designed heat pump is operated against a source of constant temperature ground water or pond water. To date, we have assembled the electronic logging devices required to prove the resultant savings. Data to date, (15 November, 1980) is sparse as we are just entering a full heating season. It is expected that a complete data log will be submitted next spring. Initial energy savings computations follow - the system efficiency is impressive. A typical winter day savings is about $24.00 or $720.00 monthly. The system utilizes the 55/sup 0/F ground water directly for summer cooling. The summer savings are estimated to be about $18.00/day or $540.00 monthly. Circuits and diagrams of the microprocessor control system and data logger are presented. Some sample data are included. (WHK)

  3. STcontrol and NEWPORT Motion Controller Model ESP 301 Device

    CERN Document Server

    Kapanadze, Giorgi

    2015-01-01

    Pixel detectors are used to detect particle tracks in LHC experiments. This kind of detectors are built with silicon semiconductor diodes. Ionizing particles create charge in the diode and the reverse bias voltage creates electric field in the diode which causes effective charge collection by the drift of electrons [1]. One of the main parameter of tracker detectors is efficiency. The efficiency as a function of position in the pixel matrix can be evaluated by scanning the matrix with red and infrared lasers. It is important to know what is happening between pixels in terms of efficiency. We perform these measurements to test new type of pixel detectors for the LHC future upgrade in 2023. New type of detectors are needed because the radiation level will be much higher [2]. For the measurements we need to control a stage motion controller (NEWPORT Motion Controller Model ESP 301) with the existing software STcontrol, which is used for readout data from pixel detectors and to control other devices like the lase...

  4. Final technical report for DOE Computational Nanoscience Project: Integrated Multiscale Modeling of Molecular Computing Devices

    Energy Technology Data Exchange (ETDEWEB)

    Cummings, P. T.

    2010-02-08

    This document reports the outcomes of the Computational Nanoscience Project, "Integrated Multiscale Modeling of Molecular Computing Devices". It includes a list of participants and publications arising from the research supported.

  5. 75 FR 17093 - Neurological and Physical Medicine Devices; Designation of Special Controls for Certain Class II...

    Science.gov (United States)

    2010-04-05

    ... comprehensive system for the regulation of medical devices intended for human use. Section 513 of the act (21 U... device regulations to establish special controls for these class II devices and to exempt some of these... Cosmetic Act (the act) (21 U.S.C. 301 et seq.), as amended by the Medical Device Amendments of 1976 (the...

  6. Randomized controlled trials in central vascular access devices: A scoping review

    Science.gov (United States)

    Keogh, Samantha; Rickard, Claire M.

    2017-01-01

    Background Randomized controlled trials evaluate the effectiveness of interventions for central venous access devices, however, high complication rates remain. Scoping reviews map the available evidence and demonstrate evidence deficiencies to focus ongoing research priorities. Method A scoping review (January 2006–December 2015) of randomized controlled trials evaluating the effectiveness of interventions to improve central venous access device outcomes; including peripherally inserted central catheters, non-tunneled, tunneled and totally implanted venous access catheters. MeSH terms were used to undertake a systematic search with data extracted by two independent researchers, using a standardized data extraction form. Results In total, 178 trials were included (78 non-tunneled [44%]; 40 peripherally inserted central catheters [22%]; 20 totally implanted [11%]; 12 tunneled [6%]; 6 non-specified [3%]; and 22 combined device trials [12%]). There were 119 trials (68%) involving adult participants only, with 18 (9%) pediatric and 20 (11%) neonatal trials. Insertion-related themes existed in 38% of trials (67 RCTs), 35 RCTs (20%) related to post-insertion patency, with fewer trials on infection prevention (15 RCTs, 8%), education (14RCTs, 8%), and dressing and securement (12 RCTs, 7%). There were 46 different study outcomes reported, with the most common being infection outcomes (161 outcomes; 37%), with divergent definitions used for catheter-related bloodstream and other infections. Conclusion More high quality randomized trials across central venous access device management are necessary, especially in dressing and securement and patency. These can be encouraged by having more studies with multidisciplinary team involvement and consumer engagement. Additionally, there were extensive gaps within population sub-groups, particularly in tunneled devices, and in pediatrics and neonates. Finally, outcome definitions need to be unified for results to be meaningful and

  7. Trajectory Dispersion Control for the Cassini Grand Finale Mission

    Science.gov (United States)

    Wong, Mau; Hahn, Yungsun; Roth, Duane; Vaquero, Mar

    2015-01-01

    The Cassini Grand Finale Mission, which consists of 22 ballistic orbits, will begin on April 22, 2017 after the last targeted Titan flyby. It will end on September 15, 2017 when the spacecraft dives into Saturn's atmosphere and be permanently captured. High volumes of unique science data from various onboard instruments are expected from the mission. To ensure its success and facilitate science planning, the trajectory dispersion needs to be controlled below 250 km (root-mean-square spatial deviation at the 68th percentile level) for a few segments of trajectory in the mission. This paper reports the formulation and solution of this dispersion control problem. We consider various sources of uncertainties including flyby error, orbit determination error, maneuver execution error, thruster firing control error, and uncertainty in Saturn's atmospheric model. A non-linear Monte Carlo Trajectory Dispersion tool is developed and employed for the analysis. It is found that a total of three Orbit Trim Maneuvers with a 99% (Delta)V usage of less than 2 m/s will adequately control the trajectory.

  8. Characterization of an oxygen plasma process for cleaning packaged semiconductor devices. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Adams, B.E.

    1996-11-01

    The purpose of this research was to experimentally determine the operating {open_quotes}window{close_quotes} for an oxygen plasma cleaning process to be used on microelectronics components just prior to wire bonding. The process was being developed to replace one that used vapor degreasing with trichlorotrifluoroethane, an ozone-depleting substance. A Box-Behnken experimental design was used to generate data from which the oxygen plasma cleaning process could be characterized. Auger electron spectrophotometry was used to measure the contamination thickness on the dice after cleaning. An empirical equation correlating the contamination thickness on the die surface with the operating parameters of the plasma system was developed from the collected Auger data, and optimum settings for cleaning semiconductor devices were determined. Devices were also tested for undesirable changes in electrical parameters resulting from cleaning in the plasma system. An increase in leakage current occurred for bipolar transistors and diodes after exposure to the oxygen plasma. Although an increase in leakage current occurred, each device`s parameter remained well below the acceptable specification limit. Based upon the experimental results, the optimum settings for the plasma cleaning process were determined to be 200 watts of power applied for five minutes in an enclosure maintained at 0.7 torr. At these settings, all measurable contamination was removed without compromising the reliability of the devices.

  9. Optimization of processing and modeling issues for thin film solar cell devices: Final report, February 3, 1997--September 1, 1998

    Energy Technology Data Exchange (ETDEWEB)

    Birkmire, R. W.; Phillips, J. E.; Shafarman, W. N.; Hegedus, S. S.; McCandless, B. E.

    2000-02-28

    This final report describes results achieved under a 20-month NREL subcontract to develop and understand thin-film solar cell technology associated to CuInSe{sub 2} and related alloys, a-Si and its alloys, and CdTe. Modules based on all these thin films are promising candidates to meet DOE's long-range efficiency, reliability and manufacturing cost goals. The critical issues being addressed under this program are intended to provide the science and engineering basis for the development of viable commercial processes and to improve module performance. The generic research issues addressed are: (1) quantitative analysis of processing steps to provide information for efficient commercial-scale equipment design and operation; (2) device characterization relating the device performance to materials properties and process conditions; (3) development of alloy materials with different bandgaps to allow improved device structures for stability and compatibility with module design; (4) development and improved window/heterojunction layers and contacts to improve device performance and reliability; and (5) evaluation of cell stability with respect to device structure and module encapsulation.

  10. Device for passive flow control around vertical axis marine turbine

    Science.gov (United States)

    Coşoiu, C. I.; Georgescu, A. M.; Degeratu, M.; Haşegan, L.; Hlevca, D.

    2012-11-01

    The power supplied by a turbine with the rotor placed in a free stream flow may be increased by augmenting the velocity in the rotor area. The energy of the free flow is dispersed and it may be concentrated by placing a profiled structure around the bare turbine in order to concentrate more energy in the rotor zone. At the Aerodynamic and Wind Engineering Laboratory (LAIV) of the Technical University of Civil Engineering of Bucharest (UTCB) it was developed a concentrating housing to be used for hydro or aeolian horizontal axis wind turbines, in order to increase the available energy in the active section of turbine rotor. The shape of the concentrating housing results by superposing several aero/hydro dynamic effects, the most important being the one generated by the passive flow control devices that were included in the housing structure. Those concentrating housings may be also adapted for hydro or aeolian turbines with vertical axis. The present paper details the numerical research effectuated at the LAIV to determine the performances of a vertical axis marine turbine equipped with such a concentrating device, in order to increase the energy quantity extracted from the main flow. The turbine is a Darrieus type one with three vertical straight blades, symmetric with respect to the axis of rotation, generated using a NACA4518 airfoil. The global performances of the turbine equipped with the concentrating housing were compared to the same characteristics of the bare turbine. In order to validate the numerical approach used in this paper, test cases from the literature resulting from experimental and numerical simulations for similar situations, were used.

  11. 78 FR 49764 - Certain Electronic Digital Media Devices and Components Thereof; Commission's Final Determination...

    Science.gov (United States)

    2013-08-15

    ... Co, Ltd. of the Republic of Korea (``SEC''); Samsung Electronics America, Inc. of Ridgefield Park... '501 patent is not infringed by the accused products represented by the Transform SPH-M920. On April 9... asserted claims of the '501 patent; that the accused Samsung devices represented by Transform SPH-M920...

  12. Assessment of control technology for stationary sources. Volume II: control technology data tables. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Minicucci, D.; Herther, M.; Babb, L.; Kuby, W.

    1980-02-01

    This report, the Control Technology Data Tables, is the second volume of the three-volume final report for the contract. It presents in tabular format, qualitative descriptions of control options for the various sources and quantitative information on control technology cost, efficiency, reliability, energy consumption, other environmental impacts and application status. Also included is a code list which classifies the stationary sources examined by industry, process, and emission source.

  13. An Implement of FPGA Based PCI Controller Device and Improvement of DDA Arc Interpolation

    Directory of Open Access Journals (Sweden)

    Zhengjie Zhang

    2014-01-01

    Full Text Available The main purpose of this paper is to develop a new kind of PCI slave device serving as a motion controller for a biaxial motion control system. This kind of controller device is a new realization scheme of PCI devices, which is embedded with a deeply customized PCI interface block instead of traditional PCI interface chips, which will greatly promote the comprehensive performance of the device. Besides, we improved the popular and widely used DDA arc interpolation algorithm, promoting its performance in both accuracy and stability, and integrated it into our device, allowing the ability of the moving parts to move along nonlinear curve paths. Currently, this kind of controller device has been successfully applied on a surface mount machine which is also developed by our lab. As a result, the controller device performs well and is able to satisfy the requirement of accuracy and velocity of the surface mount machine. And its reliability and stability are also remarkable.

  14. Primary Control by ON/OFF Demand-Side Devices

    DEFF Research Database (Denmark)

    Biegel, Benjamin; Hansen, Lars Henrik; Andersen, Palle

    2013-01-01

    manage the portfolio of devices to collectively provide a primary reserve delivery in an unbundled liberalized electricity market setting under current regulations. Furthermore, we formulate a binary linear optimization problem that minimizes the aggregator’s cost of providing a primary reserve delivery......We consider an aggregator managing a portfolio of ON/OFF demand-side devices. The devices are able to shift con- sumption in time within certain energy limitations; moreover, the devices are able to measure the system frequency and switch ON and OFF accordingly. We show how the aggregator can...

  15. Seismic Proofing Capability of the Accumulated Semiactive Hydraulic Damper as an Active Interaction Control Device with Predictive Control

    National Research Council Canada - National Science Library

    Shih, Ming-Hsiang; Sung, Wen-Pei

    2016-01-01

    .... To improve the seismic proofing capability of Accumulated Semiactive Hydraulic Damper, it is converted to an Active Interaction Control device and synchronous control and predictive control methods are proposed...

  16. System Control Applications of Low-Power Radio Frequency Devices

    Science.gov (United States)

    van Rensburg, Roger

    2017-09-01

    This paper conceptualizes a low-power wireless sensor network design for application employment to reduce theft of portable computer devices used in educational institutions today. The aim of this study is to design and develop a reliable and robust wireless network that can eradicate accessibility of a device’s human interface. An embedded system supplied by an energy harvesting source, installed on the portable computer device, may represent one of multiple slave nodes which request regular updates from a standalone master station. A portable computer device which is operated in an undesignated area or in a field perimeter where master to slave communication is restricted, indicating a possible theft scenario, will initiate a shutdown of its operating system and render the device unusable. Consequently, an algorithm in the device firmware may ensure the necessary steps are executed to track the device, irrespective whether the device is enabled. Design outcomes thus far indicate that a wireless network using low-power embedded hardware, is feasible for anti-theft applications. By incorporating one of the latest Bluetooth low-energy, ANT+, ZigBee or Thread wireless technologies, an anti-theft system may be implemented that has the potential to reduce major portable computer device theft in institutions of digitized learning.

  17. Immediate postpartum levonorgestrel intrauterine device insertion and breast-feeding outcomes: a noninferiority randomized controlled trial.

    Science.gov (United States)

    Turok, David K; Leeman, Lawrence; Sanders, Jessica N; Thaxton, Lauren; Eggebroten, Jennifer L; Yonke, Nicole; Bullock, Holly; Singh, Rameet; Gawron, Lori M; Espey, Eve

    2017-12-01

    Immediate postpartum levonorgestrel intrauterine device insertion is increasing in frequency in the United States, but few studies have investigated the effect of early placement on breast-feeding outcomes. This study examined the effect of immediate vs delayed postpartum levonorgestrel intrauterine device insertion on breast-feeding outcomes. We conducted this noninferiority randomized controlled trial at the University of Utah and the University of New Mexico Health Sciences Centers from February 2014 through March 2016. Eligible women were pregnant and planned to breast-feed, spoke English or Spanish, were aged 18-40 years, and desired a levonorgestrel intrauterine device. Enrolled women were randomized 1:1 to immediate postpartum insertion or delayed insertion at 4-12 weeks' postpartum. Prespecified exclusion criteria included delivery lactogenesis, used a validated measure, and was analyzed by survival analysis and log rank test. We followed up participants for ongoing data collection for 6 months. Only the data analysis team was blinded to the intervention. We met the enrollment target with 319 participants, but lost 34 prior to randomization and excluded an additional 26 for medical complications prior to delivery. The final analytic sample included 132 in the immediate group and 127 in the delayed group. Report of any breast-feeding at 8 weeks in the immediate group (79%; 95% confidence interval, 70-86%) was noninferior to that of the delayed group (84%; 95% confidence interval, 76-91%). The 5% difference in breast-feeding continuation at 8 weeks between the groups fell within the noninferiority margin (95% confidence interval, -5.6 to 15%). Time to lactogenesis (mean ± SD) in the immediate group, 65.3 ± 25.7 hours, was noninferior to that of the delayed group, 63.6 ± 21.6 hours. The mean difference between groups was 1.7 hours (95% confidence interval, -4.8 to 8.2 hours), noninferior by log-rank test. A total of 24 intrauterine device expulsions

  18. Analysis and demonstration of fuel-free cooling and lighting device. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1982-09-29

    Presented are the production and testing of a sun shade device. The sun shade consists of a toothed metal angle (called the jamb member) and a webbing, woven of precisely formulated filaments, which is laced horizontally from tooth to tooth of the jamb member. Testing was performed in air-conditioned and non-air-conditioned rooms of school buildings in three different climatic areas of Virginia. During a 365 day period, interior temperatures and light were monitored and continuously recorded for each room. (BCS)

  19. 67 FR 78563 - Guidance on Traffic Control Devices at Highway-Rail Grade Crossings

    Science.gov (United States)

    2002-12-24

    ...This notice announces that the FHWA has issued guidance to assist engineers in selection of traffic control devices or other measures at highway-rail crossings. The report, ``Guidance on Traffic Control Devices at Highway-Rail Grade Crossings'' is available at the following URL: http://safety.fhwa.dot.gov/media/twgreport.htm. This guidance is designed to assist in decisions to install traffic control devices or otherwise improve highway-rail grade crossings.

  20. 76 FR 17444 - In the Matter of Certain Vaginal Ring Birth Control Devices; Notice of Investigation

    Science.gov (United States)

    2011-03-29

    ... COMMISSION In the Matter of Certain Vaginal Ring Birth Control Devices; Notice of Investigation AGENCY: U.S... certain vaginal ring birth control devices by reason of infringement of claim 1 of U.S. Patent No. 6,086... importation, or the sale within the United States after importation of certain vaginal ring birth control...

  1. A Pressure Controlled Pinched Flow Fractionation Device for Continuous Particle Separation

    DEFF Research Database (Denmark)

    Christiansen, Thomas Lehrmann; Trosborg, Jacqueline; Tanzi, Simone

    2012-01-01

    the device tunable using a simple pressure control. Through analytical calculations and FEM simulations in COMSOL, the required dimensions and operating pressures of the device was determined. The device was subsequently fabricated by injection molding of a COC TOPAS grade 5013 polymer (TOPAS Advanced...

  2. Designed supramolecular assemblies for biosensors and photoactive devices. LDRD final report

    Energy Technology Data Exchange (ETDEWEB)

    Song, X.Z.; Shelnutt, J.A.; Hobbs, J.D.; Cesarano, J.

    1997-02-01

    The objective of this project is the development of a new class of supramolecular assemblies for applications in biosensors and biodevices. The supramolecular assemblies are based on membranes and Langmuir-Blodgett (LB) films composed of naturally-occurring or synthetic lipids, which contain electrically and/or photochemically active components. The LB films are deposited onto electrically-active materials (metal, semiconductors). The active components film components (lipo-porphyrins) at the surface function as molecular recognition sites for sensing proteins and other biomolecules, and the porphyrins and other components (e.g., fullerenes) incorporated into the films serve as photocatalysts and vectorial electron-transport agents. Computer-aided molecular design (CAMD) methods are used to tailor the structure of these film components to optimize function. Molecular modeling is also used to predict the location, orientation, and motion of these molecular components within the films. The result is a variety of extended, self-assembled molecular structures that serve as devices for sensing proteins and biochemicals or as other bioelectronic devices.

  3. Engineering at SLAC: Designing and constructing experimental devices for the Stanford Synchrotron Radiation Lightsource - Final Paper

    Energy Technology Data Exchange (ETDEWEB)

    Djang, Austin [SLAC National Accelerator Lab., Menlo Park, CA (United States)

    2015-08-22

    Thanks to the versatility of the beam lines at SSRL, research there is varied and benefits multiple fields. Each experiment requires a particular set of experiment equipment, which in turns requires its own particular assembly. As such, new engineering challenges arise from each new experiment. My role as an engineering intern has been to help solve these challenges, by designing and assembling experimental devices. My first project was to design a heated sample holder, which will be used to investigate the effect of temperature on a sample's x-ray diffraction pattern. My second project was to help set up an imaging test, which involved designing a cooled grating holder and assembling multiple positioning stages. My third project was designing a 3D-printed pencil holder for the SSRL workstations.

  4. Final Report. DOE Computational Nanoscience Project DE-FG02-03ER46096: Integrated Multiscale Modeling of Molecular Computing Devices

    Energy Technology Data Exchange (ETDEWEB)

    Cummings, Peter [Vanderbilt University

    2009-11-15

    The document is the final report of the DOE Computational Nanoscience Project DE-FG02-03ER46096: Integrated Multiscale Modeling of Molecular Computing Devices. It included references to 62 publications that were supported by the grant.

  5. Environmental assessment for device assembly facility operations, Nevada Test Site, Nye County, Nevada. Final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-05-01

    The U.S. Department of Energy, Nevada Operations Office (DOE/NV), has prepared an environmental assessment (EA), (DOE/EA-0971), to evaluate the impacts of consolidating all nuclear explosive operations at the newly constructed Device Assembly Facility (DAF) in Area 6 of the Nevada Test Site. These operations generally include assembly, disassembly or modification, staging, transportation, testing, maintenance, repair, retrofit, and surveillance. Such operations have previously been conducted at the Nevada Test Site in older facilities located in Area 27. The DAF will provide enhanced capabilities in a state-of-the-art facility for the safe, secure, and efficient handling of high explosives in combination with special nuclear materials (plutonium and highly enriched uranium). Based on the information and analyses in the EA, DOE has determined that the proposed action would not constitute a major federal action significantly affecting the quality of the human environment within the meaning of the National Environmental Policy Act of 1969 (42 U.S.C. 4321 et seq.). Therefore, an environmental impact statement is not required, and DOE is issuing this finding of no significant impact.

  6. Comparison and Research of the Mechanical Items of Standards for Controlled Door Closing Devices

    Science.gov (United States)

    Ren, X.; Wang, M.; Li, Z. K.; Ou, S. M.

    2017-09-01

    This paper analyzes the standards of controlled door closing devices at home and abroad, compares the standards from test devices and items, and illustrates the backcheck function, delayed action and dead stop degree test in detail. In addition, experiments have been done to verify the influence of different door weights on closing time, opening and closing moment and efficiency. The results show that the door weight has significant influence on mechanical performance of controlled door closing devices.

  7. Development of integrated superconducting devices for signal preprocessing. Final report; Entwicklung supraleitender Bausteine der Signalvorverarbeitung. Abschlussbericht

    Energy Technology Data Exchange (ETDEWEB)

    Biehl, M.; Koch, R.; Neuhaus, M.; Scherer, T.; Jutzi, W.

    1998-02-01

    SPICE and CADENCE based tools for designing, simulating and optimizing SFQ and RSFQ circuits have been developed as well as a standard cell library corresponding to the fabrication technology established at the IEGI. A 12 bit flux shuttle shift register using Nb/Al Josephson junctions with a new write and readout gate has been fabricated and tested successfully; the power dissipation is 9 nW/bit/GHz. A pseudo random pulse generator was developed correspondingly. Simulations of RSFQ toggle flipflops during a large number of clock cycles demonstrated that the digital performance of counters is limited to clock frequencies below 100 GHz by dynamic effects, especially of parasitic inductances. Therefore dc measurements based on the voltage-frequency Josephson relationship must be followed by real time measurements of single SFQ word pulses. A four stage Nb based RSFQ counter in a coplanar waveguide test jig was tested up to a frequency of 2 GHz, limited by the available 32 bit pattern generator and the bandwith of the sampling oscilloscope, yielding bit error rates of about 10{sup -12}. Using YBCO technology, a 4 bit SFQ shift register (T=40 K) as well as miniaturized coplanar microwave devices for satellite and communication applications at 10 GHz (T=77 K) have been designed and fabricated. A 4 bit instantaneous real time frequency meter (IFM) and a microwave filter with a 3-dB bandwidth of only 1.8% have been mounted on the cold head of a split-cycle Stirling cooler (AEG, 1.5 W rate at 80 K) and tested successfully. Hybrid devices, e.g. amplifiers and oscillators, combining active semiconductor components and low loss coplanar YBCO transmission lines operated at 77 K seem very promising. (orig.) [Deutsch] Werkzeuge der Auslegung, Simulation und Optimierung von SFQ- und RSFQ-Schaltungen auf der Basis von SPICE und CADENCE wurden am IEGI entwickelt und eingesetzt. Eine auf die Technologien des Instituts zugeschnittene Bibliothek von Zellen ist vorhanden. Mit der

  8. 76 FR 35015 - Certain Lighting Control Devices Including Dimmer Switches and Parts Thereof (IV); Notice of...

    Science.gov (United States)

    2011-06-15

    ... COMMISSION Certain Lighting Control Devices Including Dimmer Switches and Parts Thereof (IV); Notice of... sale for importation, and the sale within the United States after importation of certain lighting... after importation of certain lighting control devices including dimmer switches and parts thereof that...

  9. 77 FR 43612 - Certain Lighting Control Devices Including Dimmer Switches and Parts Thereof (IV); Decision To...

    Science.gov (United States)

    2012-07-25

    ... COMMISSION Certain Lighting Control Devices Including Dimmer Switches and Parts Thereof (IV); Decision To... importation, and the sale within the United States after importation of certain lighting control devices... Lighting of Los Angeles, California. On September 9, 2011, the Commission issued notice of its...

  10. 77 FR 8900 - Certain Vaginal Ring Birth Control Devices; Termination of the Investigation Based on Withdrawal...

    Science.gov (United States)

    2012-02-15

    ... From the Federal Register Online via the Government Publishing Office INTERNATIONAL TRADE COMMISSION Certain Vaginal Ring Birth Control Devices; Termination of the Investigation Based on Withdrawal... within the United States after importation of certain vaginal birth control devices by reason of...

  11. Creating a systems engineering approach for the manual on uniform traffic control devices.

    Science.gov (United States)

    2011-03-01

    The Manual on Uniform Traffic Control Devices (MUTCD) provides basic principles for use of traffic : control devices (TCD). However, most TCDs are not explicitly required, and the decision to use a given : TCD in a given situation is typically made b...

  12. Development of a Low-Lift Chiller Controller and Simplified Precooling Control Algorithm - Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Gayeski, N.; Armstrong, Peter; Alvira, M.; Gagne, J.; Katipamula, Srinivas

    2011-11-30

    KGS Buildings LLC (KGS) and Pacific Northwest National Laboratory (PNNL) have developed a simplified control algorithm and prototype low-lift chiller controller suitable for model-predictive control in a demonstration project of low-lift cooling. Low-lift cooling is a highly efficient cooling strategy conceived to enable low or net-zero energy buildings. A low-lift cooling system consists of a high efficiency low-lift chiller, radiant cooling, thermal storage, and model-predictive control to pre-cool thermal storage overnight on an optimal cooling rate trajectory. We call the properly integrated and controlled combination of these elements a low-lift cooling system (LLCS). This document is the final report for that project.

  13. Understanding and controlling chromaticity shift in LED devices

    Energy Technology Data Exchange (ETDEWEB)

    Davis, Lynn; Mills, Karmann; Lamvik, Michael; Perkins, Curtis; Bobashev, Georgiy; Young, Joseph; Yaga, Robert; Johnson, Cortina

    2017-05-30

    Chromaticity shift in light-emitting diode (LED) devices arises from multiple mechanisms, and at least five different chromaticity shift modes (CSMs) have been identified to date. This paper focuses on the impacts of irreversible phosphor degradation as a cause of chromaticity shifts in LED devices. The nitride phosphors used to produce warm white LEDs are especially vulnerable to degradation due to thermal and chemical effects such as reactions with oxygen and water. As a result, LED devices utilizing these phosphors were found to undergo either a green shift or, less commonly, a red shift depending on the phosphor mix in the LED devices. These types of chromaticity shifts are classified as CSM-2 (green shift) and CSM-5 (red shift). This paper provides an overview of the kinetic processes responsible for green and red chromaticity shifts along with examples from accelerated stress testing of 6” downlights. Both CSMs appear to proceed through analogous mechanisms that are initiated at the surface of the phosphor. A green shift is produced by the surface oxidation of the nitride phosphor that changes the emission profile to lower wavelengths. As the surface oxidation reaction proceeds, reactant limitations slow the rate and bulk oxidation processes become more prevalent. We found that a red chromaticity shift arises from quenching of the green phosphor, also possibly due to surface reactions of oxygen, which shift the emission chromaticity in the red direction. In conclusion, we discuss the implications of these findings on projecting chromaticity.

  14. State-of-the-art robotic devices for ankle rehabilitation: Mechanism and control review.

    Science.gov (United States)

    Hussain, Shahid; Jamwal, Prashant K; Ghayesh, Mergen H

    2017-12-01

    There is an increasing research interest in exploring use of robotic devices for the physical therapy of patients suffering from stroke and spinal cord injuries. Rehabilitation of patients suffering from ankle joint dysfunctions such as drop foot is vital and therefore has called for the development of newer robotic devices. Several robotic orthoses and parallel ankle robots have been developed during the last two decades to augment the conventional ankle physical therapy of patients. A comprehensive review of these robotic ankle rehabilitation devices is presented in this article. Recent developments in the mechanism design, actuation and control are discussed. The study encompasses robotic devices for treadmill and over-ground training as well as platform-based parallel ankle robots. Control strategies for these robotic devices are deliberated in detail with an emphasis on the assist-as-needed training strategies. Experimental evaluations of the mechanism designs and various control strategies of these robotic ankle rehabilitation devices are also presented.

  15. Randomized controlled crossover trial of a new oscillatory device as add-on therapy for COPD.

    Science.gov (United States)

    Fridlender, Zvi G; Arish, Nissim; Laxer, Uri; Berkman, Neville; Leibovitz, Allon; Fink, Gershon; Breuer, Raphael

    2012-12-01

    A new oscillatory device administers predetermined pressure oscillation sequences into the chest cavity over inhaled/exhaled air streams at low positive pressure. We assessed device safety and effect on 6MW performance, pulmonary function, and health-related quality-of-life (HRQOL) in moderate-to-very severe COPD in a randomized, double-blind, controlled, crossover study. Outcomes with an oscillatory device (Pulsehaler(TM), Respinova Ltd, Herzliya, Israel) and a "muted" sham device (control) of identical appearance that delivered continuous positive air pressure were compared in two groups receiving opposite treatment sequences: 2-week oscillatory device/control, 2-week washout, 2-week control/oscillatory device, 2-week washout. The clinical trial was registered ( www.clinicaltrials.gov , NCT00821418) and approved by the Hadassah-Hebrew University Medical Center Institutional Review Board (08-608). All participants signed informed consent; 22 patients completed the study with no marked differences in COPD exacerbations or side effects. A total of 91% of patients treated with the oscillatory device had a clinically significant improvement (increase >40 m) in 6MW performance. The 6MW distance with the oscillatory device increased significantly after 1 week of treatment (51.6 ± 7.6 m, +13.5 ± 2.3%, p device was significantly greater (p device but not with control. HRQL improved markedly (≥1 point) for dyspnea and mastery with the oscillatory device (p = 0.02) but not control. Treatment with a new oscillatory device appears to be safe, and to improve 6MW performance, pulmonary function, and HRQL in COPD. Further evaluation is warranted.

  16. Device Physics of Thin-Film Polycrystalline Cells and Modules: Final Report, February 1998 -- August 2001

    Energy Technology Data Exchange (ETDEWEB)

    Sites, J. R.

    2002-01-01

    This report describes the basic measurements of CdTe and CI(G)S solar cells fabricated at a number of collaborating laboratories. The first area of emphasis has been to quantitatively deduce the loss mechanisms in these cells, and to make appropriate comparisons that illuminate where progress in being made. Cells evaluated include those at or near record efficiencies and those made with new processing strategies. A second area of emphasis, the role of impurities, has focused on sodium in CIS. Cells made with varying amounts of sodium added during CIS deposition were fabricated at NREL using four types of substrates. Best performance was achieved with 0.01 to 0.1 at% sodium. The third area of study has been small-spot measurement of micro-nonuniformities. A new facility was built to focus a laser beam onto a solar cell with 1-um beam size, 1-um resolution and repeatability, and one-sun intensity. Specific projects to date have focused on CdTe and have included the local effect of CdCl2, local intermixing of sulfur, and the effect of temperature-induced stress. Documentation of cell changes at elevated temperatures has been the fourth area of study. Changes seen in CdTe J-V curves are almost certainly related to diffusion of copper from the back contact, but in most cases an activation-energy model predicts sufficient stability for a 30-year product lifetime. Transients seen in some CIS cells are primarily seen in fill-factor and are primarily driven by voltage bias rather than illumination condition. The final area of emphasis has been numerical simulations of CdTe and CI(G)S cells. Results with CdTe are able to replicate experimental data, have explained the effects of partial overlap of the primary junction with the back contact, and have shown how variations in carrier density, carrier lifetime, and CdTe layer thickness impact cell performance.

  17. Electrode-Geometry Control of the Formation of a Conductive Bridge in Oxide Resistance Switching Devices

    Science.gov (United States)

    Fujiwara, Kohei; Yajima, Takeshi; Nakamura, Yoshinobu; Rozenberg, Marcelo J.; Takagi, Hidenori

    2009-08-01

    Control of the formation of conductive bridge between the metal electrodes in planar-type resistance switching device was attempted. We demonstrated in Pt/CuO/Pt devices that, using a triangular seed electrode for soft breakdown, the position and the size of the bridge can be controlled. The decrease in the size resulted in the drastic reduction of operation voltage and current to the same level as in capacitor-type stacked device. We argue that the planar-type device might have a certain advantage for future non-volatile memory application.

  18. Description of a digital computer simulation of an Annular Momentum Control Device (AMCD) laboratory test model

    Science.gov (United States)

    Woolley, C. T.; Groom, N. J.

    1981-01-01

    A description of a digital computer simulation of an Annular Momentum Control Device (AMCD) laboratory model is presented. The AMCD is a momentum exchange device which is under development as an advanced control effector for spacecraft attitude control systems. The digital computer simulation of this device incorporates the following models: six degree of freedom rigid body dynamics; rim warp; controller dynamics; nonlinear distributed element axial bearings; as well as power driver and power supply current limits. An annotated FORTRAN IV source code listing of the computer program is included.

  19. Advanced methods for controlling untethered magnetic devices using rotating magnetic fields

    Science.gov (United States)

    Mahoney, Arthur W., Jr.

    This dissertation presents results documenting advancements on the control of untethered magnetic devices, such as magnetic "microrobots" and magnetically actuated capsule endoscopes, motivated by problems in minimally invasive medicine. This dissertation focuses on applying rotating magnetic fields for magnetic manipulation. The contributions include advancements in the way that helical microswimmers (devices that mimic the propulsion of bacterial flagella) are controlled in the presence of gravitational forces, advancements in ways that groups of untethered magnetic devices can be differentiated and semi-independently controlled, advancements in the way that untethered magnetic device can be controlled with a single rotating permanent magnet, and an improved understanding in the nature of the magnetic force applied to an untethered device by a rotating magnet.

  20. Atmospheric Simulation Using a Liquid Crystal Wavefront Controlling Device

    Science.gov (United States)

    2004-03-23

    statistics to validated models. 1.4 Methodology In the atmosphere, laser device effectiveness degrades due to beam spread and dis- tortion caused by...the source. Passing the HeNe beam through a spatial filter approximates a point source which is collimated us- ing a doublet lens. Collimating the...ordered layers. This common orientation is due to the cigar -like shape of the NLC molecules [7]. The dielectric anisotropic property of the NLC

  1. Positive train control interoperability and networking research : final report.

    Science.gov (United States)

    2015-12-01

    This document describes the initial development of an ITC PTC Shared Network (IPSN), a hosted : environment to support the distribution, configuration management, and IT governance of Interoperable : Train Control (ITC) Positive Train Control (PTC) s...

  2. Quality control of recycled asphaltic concrete : final report.

    Science.gov (United States)

    1982-07-01

    This study examined the variations found in recycled asphaltic concrete mix based upon plant quality control data and verification testing. The data was collected from four recycled hot-mix projects constructed in 1981. All plant control and acceptan...

  3. Inhaled corticosteroids for asthma: impact of practice level device switching on asthma control

    Directory of Open Access Journals (Sweden)

    Lloyd Andrew

    2009-01-01

    Full Text Available Abstract Background As more inhaled corticosteroid (ICS devices become available, there may be pressure for health-care providers to switch patients with asthma to cheaper inhaler devices. Our objective was to evaluate impact on asthma control of inhaler device switching without an accompanying consultation in general practice. Methods This 2-year retrospective matched cohort study used the UK General Practice Research Database to identify practices where ICS devices were changed without a consultation for ≥5 patients within 3 months. Patients 6–65 years of age from these practices whose ICS device was switched were individually matched with patients using the same ICS device who were not switched. Asthma control over 12 months after the switch was assessed using a composite measure including short-acting β-agonist and oral corticosteroid use, hospitalizations, and subsequent changes to therapy. Results A total of 824 patients from 55 practices had a device switch and could be matched. Over half (53% of device switches were from dry powder to metered-dose inhalers. Fewer patients in switched than matched cohort experienced successful treatment based on the composite measure (20% vs. 34% and more experienced unsuccessful treatment (51% vs. 38%. After adjusting for possible baseline confounding factors, the odds ratio for treatment success in the switched cohort compared with controls was 0.29 (95% confidence interval [CI], 0.19 to 0.44; p Conclusion Switching ICS devices without a consultation was associated with worsened asthma control and is therefore inadvisable.

  4. 75 FR 20935 - National Standards for Traffic Control Devices; the Manual on Uniform Traffic Control Devices for...

    Science.gov (United States)

    2010-04-22

    .../nchrp/nchrp_webdoc_92.pdf . Finally, in anticipation of this NPA, the American Association of State...-way streets or highways that have three or more lanes for moving motor vehicle traffic. This includes...

  5. Development of Hand Grip Assistive Device Control System for Old People through Electromyography (EMG Signal Acquisitions

    Directory of Open Access Journals (Sweden)

    Khamis Herman

    2017-01-01

    Full Text Available The hand grip assistive device is a glove to assist old people who suffer from hand weakness in their daily life activities. The device earlier control system only use simple on and off switch. This required old people to use both hand to activate the device. The new control system of the hand grip assistive device was developed to allow single hand operation for old people. New control system take advantages of electromyography (EMG and flex sensor which was implemented to the device. It was programmed into active and semi-active mode operation. EMG sensors were placed on the forearm to capture EMG signal of Flexor Digitorum Profundus muscle to activate the device. Flex sensor was used to indicate the finger position and placed on top of the finger. The signal from both sensors then used to control the device. The new control system allowed single hand operation and designed to prevent user from over depended on the device by activating it through moving their fingers.

  6. Algorithm for Public Electric Transport Schedule Control for Intelligent Embedded Devices

    Science.gov (United States)

    Alps, Ivars; Potapov, Andrey; Gorobetz, Mikhail; Levchenkov, Anatoly

    2010-01-01

    In this paper authors present heuristics algorithm for precise schedule fulfilment in city traffic conditions taking in account traffic lights. The algorithm is proposed for programmable controller. PLC is proposed to be installed in electric vehicle to control its motion speed and signals of traffic lights. Algorithm is tested using real controller connected to virtual devices and real functional models of real tram devices. Results of experiments show high precision of public transport schedule fulfilment using proposed algorithm.

  7. Rotor position and vibration control for aerospace flywheel energy storage devices and other vibration based devices

    Science.gov (United States)

    Alexander, B. X. S.

    Flywheel energy storage has distinct advantages over conventional energy storage methods such as electrochemical batteries. Because the energy density of a flywheel rotor increases quadratically with its speed, the foremost goal in flywheel design is to achieve sustainable high speeds of the rotor. Many issues exist with the flywheel rotor operation at high and varying speeds. A prominent problem is synchronous rotor vibration, which can drastically limit the sustainable rotor speed. In a set of projects, the novel Active Disturbance Rejection Control (ADRC) is applied to various problems of flywheel rotor operation. These applications include rotor levitation, steady state rotation at high speeds and accelerating operation. Several models such as the lumped mass model and distributed three-mass models have been analyzed. In each of these applications, the ADRC has been extended to cope with disturbance, noise, and control effort optimization; it also has been compared to various industry-standard controllers such as PID and PD/observer, and is proven to be superior. The control performance of the PID controller and the PD/observer currently used at NASA Glenn has been improved by as much as an order of magnitude. Due to the universality of the second order system, the results obtained in the rotor vibration problem can be straightforwardly extended to other vibrational systems, particularly, the MEMS gyroscope. Potential uses of a new nonlinear controller, which inherits the ease of use of the traditional PID, are also discussed.

  8. Fast, cheap and in control: spectral imaging with handheld devices

    Science.gov (United States)

    Gooding, Edward A.; Deutsch, Erik R.; Huehnerhoff, Joseph; Hajian, Arsen R.

    2017-05-01

    Remote sensing has moved out of the laboratory and into the real world. Instruments using reflection or Raman imaging modalities become faster, cheaper and more powerful annually. Enabling technologies include virtual slit spectrometer design, high power multimode diode lasers, fast open-loop scanning systems, low-noise IR-sensitive array detectors and low-cost computers with touchscreen interfaces. High-volume manufacturing assembles these components into inexpensive portable or handheld devices that make possible sophisticated decision-making based on robust data analytics. Examples include threat, hazmat and narcotics detection; remote gas sensing; biophotonic screening; environmental remediation and a host of other applications.

  9. Speed control device for internal combustion engines. Drehzahlregelanordnung fuer Brennkraftmaschinen

    Energy Technology Data Exchange (ETDEWEB)

    Le Bihan, B.

    1991-05-16

    In order to keep the speed constant, or even to increase it at high torque, a further controller is provided apart from the existing centrifugal force controller in a first example of the invention, which replaces the conventional adjustment screw for the basic speed setting, and permanently changes the basic speed setting on load change. According to a second example, an electronic speed control is provided, which has a setting member, which is operated electrically, hydraulically or pneumatically and which acts directly on the carburettor. The control of the setting member is done via a controller which sets the carburettor based on a manual speed signal and the actual speed.

  10. 75 FR 74128 - Manual on Uniform Traffic Control Devices (MUTCD) Compliance Dates

    Science.gov (United States)

    2010-11-30

    ... Federal Highway Administration Manual on Uniform Traffic Control Devices (MUTCD) Compliance Dates AGENCY... requests comments on compliance dates for highway agencies to upgrade their existing non-compliant traffic... Devices (MUTCD). This notice asks for responses to a series of questions about compliance dates, their...

  11. Digital Control of External Devices through the Parallel Port of a ...

    African Journals Online (AJOL)

    In this paper we carry out the digital control of external devices using the parallel port of a computer. The PC parallel port adapter that is specically designed to attach printers has been found to be useful as a general input/output port for any device or application that matches its input/output capabilities. This paper gives ...

  12. Non-invasive control interfaces for intention detection in active movement-assistive devices

    NARCIS (Netherlands)

    Lobo-Prat, J.; Kooren, P.N.; Stienen, A.H.A.; Herder, J.L.; Koopman, B.F.J.M.; Veltink, P.H.

    2014-01-01

    Active movement-assistive devices aim to increase the quality of life for patients with neuromusculoskeletal disorders. This technology requires interaction between the user and the device through a control interface that detects the user’s movement intention. Researchers have explored a wide

  13. Active vibration control testing of the SPICES program: final demonstration article

    Science.gov (United States)

    Dunne, James P.; Jacobs, Jack H.

    1996-05-01

    The Synthesis and Processing of Intelligent Cost Effective Structures (SPICES) Program is a partnership program sponsored by the Advanced Research Projects Agency. The mission of the program is to develop cost effective material processing and synthesis technologies to enable new products employing active vibration suppression and control devices to be brought to market. The two year program came to fruition in 1995 through the fabrication of the final smart components and testing of an active plate combined with two trapezoidal rails, forming an active mount. Testing of the SPICES combined active mount took place at McDonnell Douglas facilities in St. Louis, MO, in October-December 1995. Approximately 15 dB reduction in overall response of a motor mounted on the active structure was achieved. Further details and results of the SPICES combined active mount demonstration testing are outlined. Results of numerous damping and control strategies that were developed and employed in the testing are presented, as well as aspects of the design and fabrication of the SPICES active mount components.

  14. A biodegradable device for the controlled release of Piper nigrum (Piperaceae) standardized extract to control Aedes aegypti (Diptera, Culicidae) larvae.

    Science.gov (United States)

    Custódio, Kauê Muller; Oliveira, Joice Guilherme de; Moterle, Diego; Zepon, Karine Modolon; Prophiro, Josiane Somariva; Kanis, Luiz Alberto

    2016-01-01

    The significant increase in dengue, Zika, and chikungunya and the resistance of the Aedes aegypti mosquito to major insecticides emphasize the importance of studying alternatives to control this vector. The aim of this study was to develop a controlled-release device containing Piper nigrum extract and to study its larvicidal activity against Aedes aegypti. Piper nigrum extract was produced by maceration, standardized in piperine, and incorporated into cotton threads, which were inserted into hydrogel cylinders manufactured by the extrusion of carrageenan and carob. The piperine content of the extract and thread reservoirs was quantified by chromatography. The release profile from the device was assessed in aqueous medium and the larvicidal and residual activities of the standardized extract as well as of the controlled-release device were examined in Aedes aegypti larvae. The standardized extract contained 580mg/g of piperine and an LC50 value of 5.35ppm (24h) and the 3 cm thread reservoirs contained 13.83 ± 1.81mg of piperine. The device showed zero-order release of piperine for 16 days. The P. nigrum extract (25ppm) showed maximum residual larvicidal activity for 10 days, decreasing progressively thereafter. The device had a residual larvicidal activity for up to 37 days. The device provided controlled release of Piper nigrum extract with residual activity for 37 days. The device is easy to manufacture and may represent an effective alternative for the control of Aedes aegypti larvae in small water containers.

  15. Consumer-grade EEG devices: are they usable for control tasks?

    Science.gov (United States)

    Maskeliunas, Rytis; Martisius, Ignas; Vasiljevas, Mindaugas

    2016-01-01

    We present the evaluation of two well-known, low-cost consumer-grade EEG devices: the Emotiv EPOC and the Neurosky MindWave. Problems with using the consumer-grade EEG devices (BCI illiteracy, poor technical characteristics, and adverse EEG artefacts) are discussed. The experimental evaluation of the devices, performed with 10 subjects asked to perform concentration/relaxation and blinking recognition tasks, is given. The results of statistical analysis show that both devices exhibit high variability and non-normality of attention and meditation data, which makes each of them difficult to use as an input to control tasks. BCI illiteracy may be a significant problem, as well as setting up of the proper environment of the experiment. The results of blinking recognition show that using the Neurosky device means recognition accuracy is less than 50%, while the Emotiv device has achieved a recognition accuracy of more than 75%; for tasks that require concentration and relaxation of subjects, the Emotiv EPOC device has performed better (as measured by the recognition accuracy) by ∼9%. Therefore, the Emotiv EPOC device may be more suitable for control tasks using the attention/meditation level or eye blinking than the Neurosky MindWave device. PMID:27014511

  16. Consumer-grade EEG devices: are they usable for control tasks?

    Directory of Open Access Journals (Sweden)

    Rytis Maskeliunas

    2016-03-01

    Full Text Available We present the evaluation of two well-known, low-cost consumer-grade EEG devices: the Emotiv EPOC and the Neurosky MindWave. Problems with using the consumer-grade EEG devices (BCI illiteracy, poor technical characteristics, and adverse EEG artefacts are discussed. The experimental evaluation of the devices, performed with 10 subjects asked to perform concentration/relaxation and blinking recognition tasks, is given. The results of statistical analysis show that both devices exhibit high variability and non-normality of attention and meditation data, which makes each of them difficult to use as an input to control tasks. BCI illiteracy may be a significant problem, as well as setting up of the proper environment of the experiment. The results of blinking recognition show that using the Neurosky device means recognition accuracy is less than 50%, while the Emotiv device has achieved a recognition accuracy of more than 75%; for tasks that require concentration and relaxation of subjects, the Emotiv EPOC device has performed better (as measured by the recognition accuracy by ∼9%. Therefore, the Emotiv EPOC device may be more suitable for control tasks using the attention/meditation level or eye blinking than the Neurosky MindWave device.

  17. Consumer-grade EEG devices: are they usable for control tasks?

    Science.gov (United States)

    Maskeliunas, Rytis; Damasevicius, Robertas; Martisius, Ignas; Vasiljevas, Mindaugas

    2016-01-01

    We present the evaluation of two well-known, low-cost consumer-grade EEG devices: the Emotiv EPOC and the Neurosky MindWave. Problems with using the consumer-grade EEG devices (BCI illiteracy, poor technical characteristics, and adverse EEG artefacts) are discussed. The experimental evaluation of the devices, performed with 10 subjects asked to perform concentration/relaxation and blinking recognition tasks, is given. The results of statistical analysis show that both devices exhibit high variability and non-normality of attention and meditation data, which makes each of them difficult to use as an input to control tasks. BCI illiteracy may be a significant problem, as well as setting up of the proper environment of the experiment. The results of blinking recognition show that using the Neurosky device means recognition accuracy is less than 50%, while the Emotiv device has achieved a recognition accuracy of more than 75%; for tasks that require concentration and relaxation of subjects, the Emotiv EPOC device has performed better (as measured by the recognition accuracy) by ∼9%. Therefore, the Emotiv EPOC device may be more suitable for control tasks using the attention/meditation level or eye blinking than the Neurosky MindWave device.

  18. Advanced Controls for the Multi-pod Centipod WEC device

    Energy Technology Data Exchange (ETDEWEB)

    McCall, Alan [Dehlsen Associates, LLC, Santa Barabara, CA (United States); Fleming, Alex [Dehlsen Associates, LLC, Santa Barabara, CA (United States)

    2016-02-15

    Dehlsen Associates, LLC (DA) has developed a Wave Energy Converter (WEC), Centipod, which is a multiple point absorber, extracting wave energy primarily in the heave direction through a plurality of point absorber floats sharing a common stable reference structure. The objective of this project was to develop advanced control algorithms that will be used to reduce Levelized Cost of Energy (LCOE). This project investigated the use of Model Predictive Control (MPC) to improve the power capture of the WEC. The MPC controller developed in this work is a state-space, “look ahead” controller approach using knowledge of past and current states to predict future states to take action with the PTO to maximize power capture while still respecting system constraints. In order to maximize power, which is the product of force and velocity, the controller must aim to create phase alignment between excitation force and velocity. This project showed a 161% improvement in the Annual Energy Production (AEP) for the Centipod WEC when utilizing MPC, compared to a baseline, fixed passive damping control strategy. This improvement in AEP was shown to provide a substantial benefit to the WEC’s overall Cost of Energy, reducing LCOE by 50% from baseline. The results of this work proved great potential for the adoption of Model Predictive Controls in Wave Energy Converters.

  19. Interspinous process device versus standard conventional surgical decompression for lumbar spinal stenosis: Randomized controlled trial

    NARCIS (Netherlands)

    W.A. Moojen (Wouter); M.P. Arts (Mark); W.C.H. Jacobs (WIlco); E.W. van Zwet (Erik); E. van den Akker-van Marle (Elske); B.W. Koes (Bart); C.L.A.M. Vleggeert-Lankamp (Carmen); W.C. Peul (Wilco)

    2013-01-01

    markdownabstractAbstract Objective To assess whether interspinous process device implantation is more effective in the short term than conventional surgical decompression for patients with intermittent neurogenic claudication due to lumbar spinal stenosis. Design Randomized controlled

  20. Lightweight and Compace Multifunction Computer-Controlled Strength and Aerobic Training Device Project

    Data.gov (United States)

    National Aeronautics and Space Administration — TDA Research proposes to develop a computer-controlled lightweight and compact device for aerobic and resistive training (DART) to counteract muscular atrophy and...

  1. Guest Editorial Advanced Distributed Control of Energy Conversion Devices and Systems

    DEFF Research Database (Denmark)

    Davoudi, Ali; Guerrero, Josep M.; Lewis, Frank

    2014-01-01

    The papers in this special issue on advanced distributed control of energy conversion devices and systems are loosely grouped into three categories: 1) ac energy conversion systems; 2) dc energy conversion systems; and 3) optimization and standards....

  2. 40 CFR 63.693 - Standards: Closed-vent systems and control devices.

    Science.gov (United States)

    2010-07-01

    ...) Whenever gases or vapors containing HAP are vented through a closed-vent system connected to a control... of such devices include, but are not limited to, a car-seal or a lock-and-key configuration valve. (d...

  3. Compliance Assurance Monitoring Technical Guidance Document Appendix A: Electrostatic Precipitator Control Device

    Science.gov (United States)

    Compliance assurance monitoring is intended to provide a reasonable assurance of compliance with applicable requirements under the Clean Air Act for large emission units that rely on pollution control device equipment to achieve compliance.

  4. Compliance Assurance Monitoring Technical Guidance Document Appendix A: Wet Electrostatic Precipitator Control Device

    Science.gov (United States)

    Compliance assurance monitoring is intended to provide a reasonable assurance of compliance with applicable requirements under the Clean Air Act for large emission units that rely on pollution control device equipment to achieve compliance.

  5. Development of a blocking logic checking apparatus for substation measurement and control devices

    Directory of Open Access Journals (Sweden)

    Chen Li

    2017-01-01

    Full Text Available After transforming substation measurement and control devices, the traditional method of blocking logic check needs to go back and forth among the measurement and control devices, and repeatedly connect a large number of wires, which lead to tedious operation and low efficiency. This paper developed a logic verification device based on 4G wireless communication, which used the Modbus/TCP transport protocol to access Ethernet, to complete the real-time data communication with the mobile control terminal. And this paper made a request to the logic controller according to practicality and cost. And the terminal software interface was designed by the orthogonal experimental design idea. The development of this device provided a new and efficient method for logic verification.

  6. Buried waste integrated demonstration human engineered control station. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1994-09-01

    This document describes the Human Engineered Control Station (HECS) project activities including the conceptual designs. The purpose of the HECS is to enhance the effectiveness and efficiency of remote retrieval by providing an integrated remote control station. The HECS integrates human capabilities, limitations, and expectations into the design to reduce the potential for human error, provides an easy system to learn and operate, provides an increased productivity, and reduces the ultimate investment in training. The overall HECS consists of the technology interface stations, supporting engineering aids, platform (trailer), communications network (broadband system), and collision avoidance system.

  7. BIOCONAID System (Bionic Control of Acceleration Induced Dimming). Final Report.

    Science.gov (United States)

    Rogers, Dana B.; And Others

    The system described represents a new technique for enhancing the fidelity of flight simulators during high acceleration maneuvers. This technique forces the simulator pilot into active participation and energy expenditure similar to the aircraft pilot undergoing actual accelerations. The Bionic Control of Acceleration Induced Dimming (BIOCONAID)…

  8. Final Technical Report: Distributed Controls for High Penetrations of Renewables

    Energy Technology Data Exchange (ETDEWEB)

    Byrne, Raymond H. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Neely, Jason C. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Rashkin, Lee J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Trudnowski, Daniel J. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Wilson, David G. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-12-01

    The goal of this effort was to apply four potential control analysis/design approaches to the design of distributed grid control systems to address the impact of latency and communications uncertainty with high penetrations of photovoltaic (PV) generation. The four techniques considered were: optimal fixed structure control; Nyquist stability criterion; vector Lyapunov analysis; and Hamiltonian design methods. A reduced order model of the Western Electricity Coordinating Council (WECC) developed for the Matlab Power Systems Toolbox (PST) was employed for the study, as well as representative smaller systems (e.g., a two-area, three-area, and four-area power system). Excellent results were obtained with the optimal fixed structure approach, and the methodology we developed was published in a journal article. This approach is promising because it offers a method for designing optimal control systems with the feedback signals available from Phasor Measurement Unit (PMU) data as opposed to full state feedback or the design of an observer. The Nyquist approach inherently handles time delay and incorporates performance guarantees (e.g., gain and phase margin). We developed a technique that works for moderate sized systems, but the approach does not scale well to extremely large system because of computational complexity. The vector Lyapunov approach was applied to a two area model to demonstrate the utility for modeling communications uncertainty. Application to large power systems requires a method to automatically expand/contract the state space and partition the system so that communications uncertainty can be considered. The Hamiltonian Surface Shaping and Power Flow Control (HSSPFC) design methodology was selected to investigate grid systems for energy storage requirements to support high penetration of variable or stochastic generation (such as wind and PV) and loads. This method was applied to several small system models.

  9. A Model for Service Life Control of Selected Device Systems

    Directory of Open Access Journals (Sweden)

    Zieja Mariusz

    2014-04-01

    Full Text Available This paper presents a way of determining distribution of limit state exceedence time by a diagnostic parameter which determines accuracy of maintaining zero state. For calculations it was assumed that the diagnostic parameter is deviation from nominal value (zero state. Change of deviation value occurs as a result of destructive processes which occur during service. For estimation of deviation increasing rate in probabilistic sense, was used a difference equation from which, after transformation, Fokker-Planck differential equation was obtained [4, 11]. A particular solution of the equation is deviation increasing rate density function which was used for determining exceedance probability of limit state. The so-determined probability was then used to determine density function of limit state exceedance time, by increasing deviation. Having at disposal the density function of limit state exceedance time one determined service life of a system of maladjustment. In the end, a numerical example based on operational data of selected aircraft [weapon] sights was presented. The elaborated method can be also applied to determining residual life of shipboard devices whose technical state is determined on the basis of analysis of values of diagnostic parameters.

  10. Improved Controls for Fusion RF Systems. Final technical report

    Energy Technology Data Exchange (ETDEWEB)

    Casey, Jeffrey A. [Rockfield Research Inc., Las Vegas, NV (United States)

    2011-11-08

    We have addressed the specific requirements for the integrated systems controlling an array of klystrons used for Lower Hybrid Current Drive (LHCD). The immediate goal for our design was to modernize the transmitter protection system (TPS) for LHCD on the Alcator C-Mod tokamak at the MIT Plasma Science and Fusion Center (MIT-PSFC). Working with the Alcator C-Mod team, we have upgraded the design of these controls to retrofit for improvements in performance and safety, as well as to facilitate the upcoming expansion from 12 to 16 klystrons. The longer range goals to generalize the designs in such a way that they will be of benefit to other programs within the international fusion effort was met by designing a system which was flexible enough to address all the MIT system requirements, and modular enough to adapt to a large variety of other requirements with minimal reconfiguration.

  11. Analysis of Performance Resulting from the Design of Selected Hand-Held Input Control Devices and Visual Displays

    OpenAIRE

    Spencer, Ronald Allen

    2000-01-01

    Since the introduction of graphical user interfaces (GUI), input control devices have become an integral part of desktop computing. When interfacing with GUIs, these input control devices have become the human's primary means of communicating with the computer. Although there have been a number of experiments conducted on pointing devices for desktop machine, there is little research on pointing devices for wearable computer technology. This is surprising because pointing devices are a maj...

  12. Device for dynamic switching of robot control points

    DEFF Research Database (Denmark)

    2015-01-01

    The invention comprises a system for switching between control points of a robotic system involving an industrial robot including a robot arm with a number of joints and provided with a tool interest point movable in a plurality of degrees of freedom.......The invention comprises a system for switching between control points of a robotic system involving an industrial robot including a robot arm with a number of joints and provided with a tool interest point movable in a plurality of degrees of freedom....

  13. 40 CFR 424.10 - Applicability; description of the open electric furnaces with wet air pollution control devices...

    Science.gov (United States)

    2010-07-01

    ... electric furnaces with wet air pollution control devices subcategory. 424.10 Section 424.10 Protection of... MANUFACTURING POINT SOURCE CATEGORY Open Electric Furnaces With Wet Air Pollution Control Devices Subcategory § 424.10 Applicability; description of the open electric furnaces with wet air pollution control devices...

  14. Linear motion device and method for inserting and withdrawing control rods

    Science.gov (United States)

    Smith, J.E.

    Disclosed is a linear motion device and more specifically a control rod drive mechanism (CRDM) for inserting and withdrawing control rods into a reactor core. The CRDM and method disclosed is capable of independently and sequentially positioning two sets of control rods with a single motor stator and rotor. The CRDM disclosed can control more than one control rod lead screw without incurring a substantial increase in the size of the mechanism.

  15. Control Board Digital Interface Input Devices – Touchscreen, Trackpad, or Mouse?

    Energy Technology Data Exchange (ETDEWEB)

    Thomas A. Ulrich; Ronald L. Boring; Roger Lew

    2015-08-01

    The authors collaborated with a power utility to evaluate input devices for use in the human system interface (HSI) for a new digital Turbine Control System (TCS) at a nuclear power plant (NPP) undergoing a TCS upgrade. A standalone dynamic software simulation of the new digital TCS and a mobile kiosk were developed to conduct an input device study to evaluate operator preference and input device effectiveness. The TCS software presented the anticipated HSI for the TCS and mimicked (i.e., simulated) the turbine systems’ responses to operator commands. Twenty-four licensed operators from the two nuclear power units participated in the study. Three input devices were tested: a trackpad, mouse, and touchscreen. The subjective feedback from the survey indicates the operators preferred the touchscreen interface. The operators subjectively rated the touchscreen as the fastest and most comfortable input device given the range of tasks they performed during the study, but also noted a lack of accuracy for selecting small targets. The empirical data suggest the mouse input device provides the most consistent performance for screen navigation and manipulating on screen controls. The trackpad input device was both empirically and subjectively found to be the least effective and least desired input device.

  16. Flight Investigation of the Effectiveness of an Automatic Aileron Trim Control Device for Personal Airplanes

    Science.gov (United States)

    Phillips, William H; Kuehnel, Helmut A; Whitten, James B

    1957-01-01

    A flight investigation to determine the effectiveness of an automatic aileron trim control device installed in a personal airplane to augment the apparent spiral stability has been conducted. The device utilizes a rate-gyro sensing element in order to switch an on-off type of control that operates the ailerons at a fixed rate through control centering springs. An analytical study using phase-plane and analog-computer methods has been carried out to determine a desirable method of operation for the automatic trim control.

  17. [Controls of the plant endomembrane-secretory pathway]. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1991-12-31

    These studies are focused on elucidating the molecular structure of plant cell membranes with special reference to cell surface glycoproteins. The studies reported herein include use of monoclonal antibodies to characterize cell surface epitopes, construction of cDNA libraries of cell surface proteins, isolation of plant cell mutants by flow cytometry, detection of beta-glucouronidase marker enzyme systems in plants, expression go VSVG (the major envelope glycoprotein of Vesicular Stomatis Virus) in plant cells, and control of gene expression of cell membrane glycoproteins.(DT)

  18. Autotuning of PID controller by means of human machine interface device

    Directory of Open Access Journals (Sweden)

    Michał Awtoniuk

    2017-06-01

    Full Text Available More and more control systems are based on industry microprocessors like PLC controllers (Programmable Logic Controller. The most commonly used control algorithm is PID (Proportional-Integral-Derivative algorithm. Autotuning procedure is not available in every PLC. These controllers are typically used in cooperation with HMI (Human Machine Interface devices. In the study two procedures of autotuning of the PID controller were implemented in the HMI device: step method and relay method. Six tuning rules for step methods and one for relay method were chosen. The autotuning procedures on simulated controlled object and PLC controller without build-in autotuning were tested. The object of control was first order system plus time delay.

  19. Communications and control for electric power systems: Final report

    Energy Technology Data Exchange (ETDEWEB)

    Kirkham, H.

    1998-04-01

    This report is a summary of some of the work done on the Communications and Control project, with particular emphasis on the achievements during the years 1986--1996. During those years, the project moved away from concern with dispersed storage and generation and its impact on power system operation (the team was responsible for studies in this area, and for making a power system simulator that included DSG), and became involved in more concrete work aimed at applying high-tech solutions to problems of power system communications and control. This report covers work done at JPL on the following topics: (1) the measurement of electric and magnetic fields, both ac and dc; (2) the use of optical power to supply low-power electronics; (3) the design of a fault-tolerant communication system designed for distribution automation; and (4) a digital phase locked loop that allows the use of low-power transmitting electronics to recreate a good-quality signal at the receiver. In a report of this kind, only the results and highlights of the work are described.

  20. Silk-based resorbable electronic devices for remotely controlled therapy and in vivo infection abatement.

    Science.gov (United States)

    Tao, Hu; Hwang, Suk-Won; Marelli, Benedetto; An, Bo; Moreau, Jodie E; Yang, Miaomiao; Brenckle, Mark A; Kim, Stanley; Kaplan, David L; Rogers, John A; Omenetto, Fiorenzo G

    2014-12-09

    A paradigm shift for implantable medical devices lies at the confluence between regenerative medicine, where materials remodel and integrate in the biological milieu, and technology, through the use of recently developed material platforms based on biomaterials and bioresorbable technologies such as optics and electronics. The union of materials and technology in this context enables a class of biomedical devices that can be optically or electronically functional and yet harmlessly degrade once their use is complete. We present here a fully degradable, remotely controlled, implantable therapeutic device operating in vivo to counter a Staphylococcus aureus infection that disappears once its function is complete. This class of device provides fully resorbable packaging and electronics that can be turned on remotely, after implantation, to provide the necessary thermal therapy or trigger drug delivery. Such externally controllable, resorbable devices not only obviate the need for secondary surgeries and retrieval, but also have extended utility as therapeutic devices that can be left behind at a surgical or suturing site, following intervention, and can be externally controlled to allow for infection management by either thermal treatment or by remote triggering of drug release when there is retardation of antibiotic diffusion, deep infections are present, or when systemic antibiotic treatment alone is insufficient due to the emergence of antibiotic-resistant strains. After completion of function, the device is safely resorbed into the body, within a programmable period.

  1. Device for self-verifying temperature measurement and control

    Science.gov (United States)

    Watkins, Arthur D.; Cannon, Collins P.; Tolle, Charles R.

    2004-08-03

    A measuring instrument includes a first temperature sensor, a second temperature sensor and circuitry. The first and second temperature sensors each generate a signal indicative of the temperature of a medium being detected. The circuitry is configured to activate verification of temperature being sensed with the first sensor. According to one construction, the first temperature sensor comprises at least one thermocouple temperature sensor and the second temperature sensor comprises an optical temperature sensor, each sensor measuring temperature over the same range of temperature, but using a different physical phenomena. Also according to one construction, the circuitry comprises a computer configured to detect failure of one of the thermocouples by comparing temperature of the optical temperature sensor with each of the thermocouple temperature sensors. Even further, an output control signal is generated via a fuzzy inference machine and control apparatus.

  2. Modelling and Control of Robotic Leg as Assistive Device

    Science.gov (United States)

    Jingye, Yee; Zain, Badrul Aisham bin Md

    2017-10-01

    The ageing population (people older than 60 years old) is expected to constitute 21.8% of global population by year 2050. When human ages, bodily function including locomotors will deteriorate. Besides, there are hundreds of thousands of victims who suffer from multiple health conditions worldwide that leads to gait impairment. A promising solution will be the lower limb powered-exoskeleton. This study is to be a start-up platform to design a lower limb powered-exoskeleton for a normal Malaysian male, by designing and simulating the dynamic model of a 2-link robotic leg to observe its behaviour under different input conditions with and without a PID controller. Simulink in MATLAB software is used as the dynamic modelling and simulation software for this study. It is observed that the 2-links robotic leg behaved differently under different input conditions, and perform the best when it is constrained and controlled by PID controller. Simulink model is formed as a foundation for the upcoming researches and can be modified and utilised by the future researchers.

  3. Automotive Test Rig Final Design Report. Volume 2. Control System.

    Science.gov (United States)

    1986-01-01

    t I .L L01_ COMMONJ /IUiOUT/ C:KF~.T, tASNO-tl± v it.SNOL - t5a±J- A UIWIUN111- 1C LI MILU 1f 7 1 No:: I , niyr ~flNULY .LI I Jl" u"f3Sr t 121-1...DEVELOPMENT 7.1 APPENDIX A ATR CONTROL SOFTWARE LISTING A.1 APPENDIX B INDIVIDUAL CIRCUIT DIAGRAMS 8.1 • . . :... . v s, Distribution Statezent A...VDC 407𔃿 5 1- :Microcomp uar For Left Turns c kro -’ •1Micro s v s I Desired Turn Ratio - (.00097) Integer -.04 al Value For Ugh.t Turns Micro

  4. Fiscal Year 2011 Director’s Strategic Initiative Final Report Heterogeneous Device Architectures Incorporating Nitride Semiconductors for Enhanced Functionality of Optoelectronic Devices

    Science.gov (United States)

    2014-03-01

    optimal performance. The GaN regions of these devices were deposited directly on the Si-face 4H-SiC structure by plasma-assisted molecular beam epitaxy at...spontaneous polarization, different crystal structure or a new functionality hold promise for devices with improved performance. This report discusses...research efforts on two representative examples, III-Nitride/silicon carbide (SiC) avalanche photodetectors and compositionally inhomogeneous indium

  5. Fuzzy maintenance costs of a wind turbine pitch control device

    Directory of Open Access Journals (Sweden)

    Mariana Carvalho

    2015-07-01

    Full Text Available This paper deals with the problem of estimation maintenance costs for the case of the pitch controls system of wind farms turbines. Previous investigations have estimated these costs as (traditional “crisp” values, simply ignoring the uncertainty nature of data and information available. This paper purposes an extended version of the estimation model by making use of the Fuzzy Set Theory. The results alert decision-makers to consequent uncertainty of the estimations along with their overall level, thus improving the information given to the mainte-nance support system.

  6. Quality Control Method for a Micro-Nano-Channel Microfabricated Device

    Science.gov (United States)

    Grattoni, Alessandro; Ferrari, Mauro; Li, Xuewu

    2012-01-01

    A variety of silicon-fabricated devices is used in medical applications such as drug and cell delivery, and DNA and protein separation and analysis. When a fluidic device inlet is connected to a compressed gas reservoir, and the outlet is at a lower pressure, a gas flow occurs through the membrane toward the outside. The method relies on the measurement of the gas pressure over the elapsed time inside the upstream and downstream environments. By knowing the volume of the upstream reservoir, the gas flow rate through the membrane over the pressure drop can be calculated. This quality control method consists of measuring the gas flow through a device and comparing the results with a standard curve, which can be obtained by testing standard devices. Standard devices can be selected through a variety of techniques, both destructive and nondestructive, such as SEM, AFM, and standard particle filtration.

  7. Real-Time Occupant Based Plug-in Device Control Using ICT in Office Buildings

    Directory of Open Access Journals (Sweden)

    Woo-Bin Bae

    2016-03-01

    Full Text Available The purpose of this study is to reduce the unnecessary plug loads used by computers, monitors, and computer peripheral devices, all of which account for more than 95% of the entire plug loads of an office building. To this end, an occupant-based plug-in device control (OBC-P software was developed. The OBC-P software collects real-time information about the presence or absence of occupants who are connected to the access point through the Wifi and controls the power of monitors or computers, while a standby power off device controls computer peripheral devices. To measure the plug load saving of the occupant-based plug-in device control, an experiment was conducted, targeting 10 occupants of three research labs of the graduate school, for two weeks. The experiment results showed that it could save the plug loads of monitors and computer peripheral devices by 15% in the Awake mode, and by 26% in the Sleep mode.

  8. Electric and hybrid vehicle environmental control subsystem study. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Heitner, K. L.

    1980-12-04

    The purpose of this study is to select the best technologies for the environmental control subsystem (ECS) for interior heating and cooling in electric and hybrid vehicles. The best technology must be selected from technologies that are available in the near term. The selected technology will serve as a basis on which development of a prototype ECS could start immediately. The technology selected as best ECS for the electric vehicle is the combination of a combustion heater and gasoline engine (Otto cycle) driven vapor compression air conditioner. All of the major ECS components, i.e., the combustion heater, the small gasoline engine, and the vapor compression air conditioner are commercially available. These technologies have good cost and performance characteristics. The cost for this best ECS is relatively close to the cost of current ECS's. At the same time, its effect on the vehicle's propulsion battery is minimal and the ECS size and weight do not have significant impact on the vehicle's range. The required technology also minimizes risk for the vehicle manufacturer because little new capital investment will be needed to produce the ECS. Since electric vehicles are likely to be in limited production for several years, the technology is appropriate for the market size.

  9. Distributed smart device for monitoring, control and management of electric loads in domotic environments.

    Science.gov (United States)

    Morales, Ricardo; Badesa, Francisco J; García-Aracil, Nicolas; Perez-Vidal, Carlos; Sabater, Jose María

    2012-01-01

    This paper presents a microdevice for monitoring, control and management of electric loads at home. The key idea is to compact the electronic design as much as possible in order to install it inside a Schuko socket. Moreover, the electronic Schuko socket (electronic microdevice + Schuko socket) has the feature of communicating with a central unit and with other microdevices over the existing powerlines. Using the existing power lines, the proposed device can be installed in new buildings or in old ones. The main use of this device is to monitor, control and manage electric loads to save energy and prevent accidents produced by different kind of devices (e.g., iron) used in domestic tasks. The developed smart device is based on a single phase multifunction energy meter manufactured by Analog Devices (ADE7753) to measure the consumption of electrical energy and then to transmit it using a serial interface. To provide current measurement information to the ADE7753, an ultra flat SMD open loop integrated circuit current transducer based on the Hall effect principle manufactured by Lem (FHS-40P/SP600) has been used. Moreover, each smart device has a PL-3120 smart transceiver manufactured by LonWorks to execute the user's program, to communicate with the ADE7753 via serial interface and to transmit information to the central unit via powerline communication. Experimental results show the exactitude of the measurements made using the developed smart device.

  10. Distributed Smart Device for Monitoring, Control and Management of Electric Loads in Domotic Environments

    Directory of Open Access Journals (Sweden)

    Carlos Perez-Vidal

    2012-04-01

    Full Text Available This paper presents a microdevice for monitoring, control and management of electric loads at home. The key idea is to compact the electronic design as much as possible in order to install it inside a Schuko socket. Moreover, the electronic Schuko socket (electronic microdevice + Schuko socket has the feature of communicating with a central unit and with other microdevices over the existing powerlines. Using the existing power lines, the proposed device can be installed in new buildings or in old ones. The main use of this device is to monitor, control and manage electric loads to save energy and prevent accidents produced by different kind of devices (e.g., iron used in domestic tasks. The developed smart device is based on a single phase multifunction energy meter manufactured by Analog Devices (ADE7753 to measure the consumption of electrical energy and thento transmit it using a serial interface. To provide current measurement information to the ADE7753, an ultra flat SMD open loop integrated circuit current transducer based on the Hall effect principle manufactured by Lem (FHS-40P/SP600 has been used. Moreover, each smart device has a PL-3120 smart transceiver manufactured by LonWorks to execute the user’s program, to communicate with the ADE7753 via serial interface and to transmit information to the central unit via powerline communication. Experimental results show the exactitude of the measurements made using the developed smart device.

  11. Investigations of the Impact of Biodiesel Metal Contaminants on Emissions Control Devices

    Energy Technology Data Exchange (ETDEWEB)

    Brookshear, Daniel W [ORNL; Lance, Michael J [ORNL; Mccormick, Robert [National Renewable Energy Laboratory (NREL); Toops, Todd J [ORNL

    2017-01-01

    Biodiesel is a renewable fuel with the potential to displace a portion of petroleum use. However, as with any alternative fuel, in order to be a viable choice it must be compatible with the emissions control devices. The finished biodiesel product can contain up to 5 ppm Na + K and 5 ppm Ca + Mg, and these metal impurities can lead to durability issues with the devices used to control emissions in diesel vehicles. Significant work has been performed to understand how the presence of these metals impacts each individual component of diesel emissions control systems, and this chapter summarizes the findings of these research efforts.

  12. Investigations of the Impact of Biodiesel Metal Contaminants on Emissions Control Devices

    Energy Technology Data Exchange (ETDEWEB)

    Brookshear, D. W.; Lance, M. J.; McCormick, Robert L.; Toops, T. J.

    2017-02-27

    Biodiesel is a renewable fuel with the potential to displace a portion of petroleum use. However, as with any alternative fuel, in order to be a viable choice it must be compatible with the emissions control devices. The finished biodiesel product can contain up to 5 ppm Na+K and 5 ppm Ca+Mg, and these metal impurities can lead to durability issues with the devices used to control emissions in diesel vehicles. Significant work has been performed to understand how the presence of these metals impacts each individual component of diesel emissions control systems, and this chapter summarizes the findings of these research efforts.

  13. COMPUTER CONTROLLED EXPERIMENTAL DEVICE FOR INVESTIGATIONS OF TRIBOLOGICAL INFLUENCES IN SHEET METAL FORMING

    OpenAIRE

    Milan Djordjevic; Srbislav Aleksandrović; Tomislav Vujinović; Milentije Stefanović; Vukić Lazić; Ružica Nikolić

    2012-01-01

    Sheet metal forming, especially deep drawing process, is influenced by many factors. Blank holding force and drawbead displacement are two of them that can be controlled during the forming process. For this purpose, electro-hydraulic computerized sheet-metal strip sliding device has been constructed. Basic characteristic of this device is realization of variable contact pressure and drawbead height as functions of time or stripe displacement. There are both, pressure and drawbead, ten linear ...

  14. The new realized mobile device for extremal control research and presentation

    Directory of Open Access Journals (Sweden)

    Matej URBANSKÝ

    2015-12-01

    Full Text Available At our department we deal with torsional oscillating mechanical systems (TOMS continuous tuning during its operation in terms of torsional oscillation size. Therefore was build the new mobile device for research and presentation purposes of the TOMS continuous tuning using extremal control method. This paper deals mainly with design of the mobile device and its special compressed air distribution system, which is necessary for its regular function.

  15. Control of Fuel Microorganisms with Magnetic Devices: Laboratory Investigation with Hormoconis Resinae

    Science.gov (United States)

    1991-11-01

    Aircraft Materials Technical Memorandum 408 CONTROL OF FUEL MICROORGANISMS WITH MAGNETIC DEVICES: LABORATORY INN, ESTIGATION WITH HORMOCONIS RESINAE ... RESINAE by G.G. McVEA R.K. SOLLY SUMMARY Automotive diesel fuel inoculated with the fungus, Hornoconis resinae , wascirculated through a magnetic device...HORMOCONIS resinae (often known by its previous name of Cladosporium resinae ) forms mats of slimy mycelia matter, which has a very high propensity to

  16. 76 FR 78 - Federal Motor Vehicle Safety Standard; Engine Control Module Speed Limiter Device

    Science.gov (United States)

    2011-01-03

    ... posted speed limit of 55 mph that was in effect in 1991. \\2\\ Comercial Motor Vehicle Speed Control... improved truck designs. \\3\\ Comercial Motor Vehicle Speed Control Devices (1991), DOT HS 807 725. TCA... National Highway Traffic Safety Administration 49 CFR Part 571 Federal Motor Vehicle Safety Standard...

  17. Quality Control Assessment of Radiology Devices in Kerman Province, Iran

    Directory of Open Access Journals (Sweden)

    Zahra Jomehzadeh

    2016-03-01

    Full Text Available Introduction Application of quality control (QC programs at diagnostic radiology departments is of great significance for optimization of image quality and reduction of patient dose. The main objective of this study was to perform QC tests on stationary radiographic X-ray machines, installed in 14 hospitals of Kerman province, Iran. Materials and Methods In this cross-sectional study, QC tests were performed on 28 conventional radiographic X-ray units in Kerman governmental hospitals, based on the protocols and criteria recommended by the Atomic Energy Organization of Iran (AEOI, using a calibrated Gammex QC kit. Each section of the QC kit incorporated different models. Results Based on the findings, kVp accuracy, kVp reproducibility, timer accuracy, timer reproducibility, exposure reproducibility, mA/timer linearity, and half-value layer were not within the acceptable limits in 25%, 4%, 29%, 18%, 11%, 12%, and 7% of the evaluated units (n=28, respectively. Conclusion As radiographic X-ray equipments in Kerman province are relatively old with a high workload, it is recommended that AEOI modify the current policies by changing the frequency of QC test implementation to at least once a year.

  18. A biodegradable device for the controlled release of Piper nigrum (Piperaceae standardized extract to control Aedes aegypti (Diptera, Culicidae larvae

    Directory of Open Access Journals (Sweden)

    Kauê Muller Custódio

    Full Text Available Abstract: INTRODUCTION: The significant increase in dengue, Zika, and chikungunya and the resistance of the Aedes aegypti mosquito to major insecticides emphasize the importance of studying alternatives to control this vector. The aim of this study was to develop a controlled-release device containing Piper nigrum extract and to study its larvicidal activity against Aedes aegypti. METHODS: Piper nigrum extract was produced by maceration, standardized in piperine, and incorporated into cotton threads, which were inserted into hydrogel cylinders manufactured by the extrusion of carrageenan and carob. The piperine content of the extract and thread reservoirs was quantified by chromatography. The release profile from the device was assessed in aqueous medium and the larvicidal and residual activities of the standardized extract as well as of the controlled-release device were examined in Aedes aegypti larvae. RESULTS The standardized extract contained 580mg/g of piperine and an LC50 value of 5.35ppm (24h and the 3 cm thread reservoirs contained 13.83 ± 1.81mg of piperine. The device showed zero-order release of piperine for 16 days. The P. nigrum extract (25ppm showed maximum residual larvicidal activity for 10 days, decreasing progressively thereafter. The device had a residual larvicidal activity for up to 37 days. CONCLUSIONS: The device provided controlled release of Piper nigrum extract with residual activity for 37 days. The device is easy to manufacture and may represent an effective alternative for the control of Aedes aegypti larvae in small water containers.

  19. Second generation OLED devices and systems: inline evaporation, highly efficient OLED devices, and novel driver/controller ASICs

    Science.gov (United States)

    Amelung, Joerg; Toerker, Michael; Luber, Claus; Eritt, Michael; Tomita, Yuto; Cholewa, Harald; Hermann, Ruediger; Loeffler, Frank; May, Christian; Vogel, Uwe; Bunk, Gerd; Heinig, Andreas; Jeroch, Werner; Holland, Hans-Jürgen; Leo, Karl

    2005-07-01

    Organic light-emitting diodes (OLED) have to be improved to achieve new market segments in displays and lighting applications. We present important steps towards achieving this goal in a combination of highly efficient devices, manufacturing and new driving aspects. It is generally expected that the manufacturing methods have to be made more efficient to achieve large market penetration. We firstly present results on a highly efficient RGB-OLED-system with doped transport layer, manufactured in the worldwide first vertical In-Line set-up. Additionally a second-generation passive matrix OLED controller/driver IC was developed. Though the design was application-specifically directed for the onto integration into an OLED minidisplay panel module (e.g., by pad layout design being closely related to display connection schemes), versatile service in various applications was focused on. Therefore, in general they may also act as application-specific standard products (ASSP), if their built-in functions provide compatibility to a wide range of passive-matrix OLED panels. Additionally, the second generation supports various PMOLED display resolutions, area or full-color (RGB) operating modes and circuit techniques for OLED devices lifetime improvement.

  20. Final Report - Investigation of Intermittent Turbulence and Turbulent Structures in the Presence of Controlled Sheared Flows

    Energy Technology Data Exchange (ETDEWEB)

    Gilmore, Mark A. [University of New Mexico

    2013-06-27

    Final Report for grant DE-FG02-06ER54898. The dynamics and generation of intermittent plasma turbulent structures, widely known as "blobs" have been studied in the presence of sheared plasma flows in a controlled laboratory experiment.

  1. Final Rule for Control of Hazardous Air Pollutants From Mobile Sources: Early Credit Technology Requirement Revision

    Science.gov (United States)

    EPA is taking final action to revise the February 26, 2007 mobile source air toxics rule’s requirements that specify which benzene control technologies a refiner may utilize to qualify to generate early benzene credits.

  2. 76 FR 77016 - Controlled Substances: Final Adjusted Aggregate Production Quotas for 2011

    Science.gov (United States)

    2011-12-09

    ..., and thebaine were insufficient to provide for the estimated medical, scientific, research, and... 56810 are sufficient to meet the current 2011 estimated medical, scientific, research, and industrial... Enforcement Administration Controlled Substances: Final Adjusted Aggregate Production Quotas for 2011 AGENCY...

  3. Open-loop versus closed-loop control of MEMS devices: choices and issues

    Science.gov (United States)

    Borovic, B.; Liu, A. Q.; Popa, D.; Cai, H.; Lewis, F. L.

    2005-10-01

    From a controls point of view, micro electromechanical systems (MEMS) can be driven in an open-loop and closed-loop fashion. Commonly, these devices are driven open-loop by applying simple input signals. If these input signals become more complex by being derived from the system dynamics, we call such control techniques pre-shaped open-loop driving. The ultimate step for improving precision and speed of response is the introduction of feedback, e.g. closed-loop control. Unlike macro mechanical systems, where the implementation of the feedback is relatively simple, in the MEMS case the feedback design is quite problematic, due to the limited availability of sensor data, the presence of sensor dynamics and noise, and the typically fast actuator dynamics. Furthermore, a performance comparison between open-loop and closed-loop control strategies has not been properly explored for MEMS devices. The purpose of this paper is to present experimental results obtained using both open- and closed-loop strategies and to address the comparative issues of driving and control for MEMS devices. An optical MEMS switching device is used for this study. Based on these experimental results, as well as computer simulations, we point out advantages and disadvantages of the different control strategies, address the problems that distinguish MEMS driving systems from their macro counterparts, and discuss criteria to choose a suitable control driving strategy.

  4. Rankine cycle condenser pressure control using an energy conversion device bypass valve

    Science.gov (United States)

    Ernst, Timothy C; Nelson, Christopher R; Zigan, James A

    2014-04-01

    The disclosure provides a waste heat recovery system and method in which pressure in a Rankine cycle (RC) system of the WHR system is regulated by diverting working fluid from entering an inlet of an energy conversion device of the RC system. In the system, an inlet of a controllable bypass valve is fluidly coupled to a working fluid path upstream of an energy conversion device of the RC system, and an outlet of the bypass valve is fluidly coupled to the working fluid path upstream of the condenser of the RC system such that working fluid passing through the bypass valve bypasses the energy conversion device and increases the pressure in a condenser. A controller determines the temperature and pressure of the working fluid and controls the bypass valve to regulate pressure in the condenser.

  5. Cost-benefit analysis of installing dust control devices in the agate industry, Khambhat (Gujarat).

    Science.gov (United States)

    Bhagia, Lakho J; Sadhu, H G

    2008-12-01

    It is well known that an exposure to crystalline silica gives rise to silicosis and silico-tuberculosis (TB). In the agate industry of Khambhat (Gujarat) not only workers but also people staying in the vicinity of the agate-grinding facilities are exposed to crystalline silica. To reduce their dust exposure, dust control devices were developed. There are approximately 500 grinding machines located in Khambhat. A cost-benefit analysis of installing dust control devices on all agate-grinding machines was carried out by adding all positive factors and benefits and subtracting the negatives and costs. It was concluded that by installing dust control devices not only could the prevalence of silicosis and TB be reduced but also, in the long run, there could be financial benefits.

  6. Hemostasis pad combined with compression device after transradial coronary procedures: A randomized controlled trial.

    Science.gov (United States)

    Kang, Si-Hyuck; Han, Donghoon; Kim, Sehun; Yoon, Chang-Hwan; Park, Jin-Joo; Suh, Jung-Won; Cho, Young-Seok; Youn, Tae-Jin; Chae, In-Ho

    2017-01-01

    Arterial access and hemostasis are important processes during percutaneous coronary procedures. In this study, we tested if the use of chitosan-based pads on top of compression devices could improve hemostasis efficacy compared with compression devices alone after transradial coronary angiography or interventions. This study was a single-center open-label randomized controlled trial. Patients who underwent coronary angiography or intervention with the transradial approach were randomly assigned to the study (compression device and a chitosan-based pad) or control (compression devices alone) group in a 2:1 fashion. The primary endpoint was time to hemostasis, categorized into ≤5, 6-10, 11-20, and >20 minutes. Between April and July 2016, 95 patients were enrolled (59 were assigned to the study arm and 36 to the control arm). Time to hemostasis, the primary endpoint, was significantly lower in the study group than in the control group (phemostasis pad in combination with rotatory compression devices is a safe and effective hemostasis strategy after radial artery access. ClinicalTrials.gov NCT02954029.

  7. Hemostasis pad combined with compression device after transradial coronary procedures: A randomized controlled trial.

    Directory of Open Access Journals (Sweden)

    Si-Hyuck Kang

    Full Text Available Arterial access and hemostasis are important processes during percutaneous coronary procedures. In this study, we tested if the use of chitosan-based pads on top of compression devices could improve hemostasis efficacy compared with compression devices alone after transradial coronary angiography or interventions.This study was a single-center open-label randomized controlled trial. Patients who underwent coronary angiography or intervention with the transradial approach were randomly assigned to the study (compression device and a chitosan-based pad or control (compression devices alone group in a 2:1 fashion. The primary endpoint was time to hemostasis, categorized into ≤5, 6-10, 11-20, and >20 minutes.Between April and July 2016, 95 patients were enrolled (59 were assigned to the study arm and 36 to the control arm. Time to hemostasis, the primary endpoint, was significantly lower in the study group than in the control group (p<0.001. Both groups showed low rates of vascular complications.This study suggests that the use of a hemostasis pad in combination with rotatory compression devices is a safe and effective hemostasis strategy after radial artery access.ClinicalTrials.gov NCT02954029.

  8. New implantable therapeutic device for the control of an atrial fibrillation attack using the Peltier element.

    Science.gov (United States)

    Yambe, Tomoyuki; Sumiyoshi, Taketada; Koga, Chihiro; Shiraishi, Yasuyuki; Miura, Hidekazu; Sugita, Norihiro; Tanaka, Akira; Yoshizawa, Makoto

    2012-01-01

    For the development of the new therapeutic device for the atrial fibrillation, implantable cooling device using Peltier element was developed in this study. An implantable cooling device had been consisted from Peltier element with transcutaneous energy transmission system (TETS). 1st coil can be contacted from outside of the body, when the patients will feel palpitation. Electrical current will be induced to the implanted 2nd coil. Peltier element will able to cool the surface of the atrium. For the confirmation of the effect of the cooling device, trial manufacture model was developed. Animal experiments using six healthy adult goats after animal ethical committee allowance was carried out. Fourth intercostals space had been opened after anesthesia inhalation, and various sensors had been inserted. AF was induced by the electrical current with battery. As the results, AF had been recovered to the normal sinus rhythm after cooling in all six goats. So, this cooling system for the control of AF showed evident effect in these experiments. Smaller size cooling device has been under development aiming at totally implantable type. Catheter type cooling device for the insertion by the use of fiber-scope type is now under planning for the clinical application. This new type device may be able to become good news for the patients with uncontrollable AF.

  9. 40 CFR 63.3966 - How do I determine the add-on control device emission destruction or removal efficiency?

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 12 2010-07-01 2010-07-01 true How do I determine the add-on control... with Add-on Controls Option § 63.3966 How do I determine the add-on control device emission destruction... add-on control device emission destruction or removal efficiency as part of the performance test...

  10. Remote device control and monitor system for the LHD deuterium experiments

    Energy Technology Data Exchange (ETDEWEB)

    Nakanishi, Hideya, E-mail: nakanisi@nifs.ac.jp [National Institute for Fusion Science (NIFS), Toki, Gifu 509-5292 (Japan); Dept. Fusion Science, SOKENDAI (The Graduate University for Advanced Studies), Toki, Gifu 509-5292 (Japan); Ohsuna, Masaki; Ito, Tatsuki; Nonomura, Miki; Imazu, Setsuo; Emoto, Masahiko; Iwata, Chie; Yoshida, Masanobu; Yokota, Mitsuhiro; Maeno, Hiroya; Aoyagi, Miwa; Ogawa, Hideki; Nakamura, Osamu; Morita, Yoshitaka; Inoue, Tomoyuki; Watanabe, Kiyomasa [National Institute for Fusion Science (NIFS), Toki, Gifu 509-5292 (Japan); Ida, Katsumi; Ishiguro, Seiji; Kaneko, Osamu [National Institute for Fusion Science (NIFS), Toki, Gifu 509-5292 (Japan); Dept. Fusion Science, SOKENDAI (The Graduate University for Advanced Studies), Toki, Gifu 509-5292 (Japan)

    2016-11-15

    Highlights: • Device remote control will be significant for the LHD deuterium experiments. • A central management GUI to control the power distribution for devices. • For safety, power management is separated from operational commanding. • Wi-Fi was tested and found to be not reliable with fusion plasmas. - Abstract: Upon beginning the LHD deuterium experiment, the opportunity for maintenance work in the torus hall will be conspicuously reduced such that all instruments must be controlled remotely. The LHD data acquisition (DAQ) and archiving system have been using about 110 DAQ front-end, and the DAQ central control and monitor system has been implemented for their remote management. This system is based on the “multi-agent” model whose communication protocol has been unified. Since DAQ front-end electronics would suffer from the “single-event effect” (SEE) of D-D neutrons, software-based remote operation might become ineffective, and then securely intercepting or recycling the electrical power of the device would be indispensable for recovering from a non-responding fault condition. In this study, a centralized control and monitor system has been developed for a number of power distribution units (PDUs). This system adopts the plug-in structure in which the plug-in modules can absorb the differences among the commercial products of numerous vendors. The combination of the above-mentioned functionalities has led to realizing the flexible and highly reliable remote control infrastructure for the plasma diagnostics and the device management in LHD.

  11. A Numerical Analysis of Phononic-Assisted Control of Ultrasound Waves in Acoustofluidic Device

    DEFF Research Database (Denmark)

    Moiseyenko, Rayisa; Bruus, Henrik

    2015-01-01

    diffractors, which can be introduced in acoustofluidic structures. These diffractors can be applied in the design of efficient resonant cavities, directional sound waves for new types of particle sorting methods, or acoustically controlled deterministic lateral displacement. The PnC-diffractor-based devices...... and streaming has received much attention, since it relies solely on mechanical properties such as particle size and contrast in density and compressibility. We present a theoretical study of phononic-assisted control of ultrasound waves in acoustofluidic devices. We propose the use of phononic crystal...

  12. Micromechanical Devices for Control of Cell-Cell Interaction, and Methods of Use Thereof

    Science.gov (United States)

    Bhatia, Sangeeta N. (Inventor); Hui, Elliot (Inventor)

    2017-01-01

    The development and function of living tissues depends largely on interactions between cells that can vary in both time and space; however, temporal control of cell-cell interaction is experimentally challenging. By employing a micromachined silicon substrate with moving parts, herein is disclosed the dynamic regulation of cell-cell interactions via direct manipulation of adherent cells with micron-scale precision. The inventive devices and methods allow mechanical control of both tissue composition and spatial organization. The inventive device and methods enable the investigation of dynamic cell-cell interaction in a multitude of applications, such as intercellular communication, spanning embryogenesis, homeostasis, and pathogenic processes.

  13. Instrumentation and control of harmonic oscillators via a single-board microprocessor-FPGA device.

    Science.gov (United States)

    Picone, Rico A R; Davis, Solomon; Devine, Cameron; Garbini, Joseph L; Sidles, John A

    2017-04-01

    We report the development of an instrumentation and control system instantiated on a microprocessor-field programmable gate array (FPGA) device for a harmonic oscillator comprising a portion of a magnetic resonance force microscope. The specific advantages of the system are that it minimizes computation, increases maintainability, and reduces the technical barrier required to enter the experimental field of magnetic resonance force microscopy. Heterodyne digital control and measurement yields computational advantages. A single microprocessor-FPGA device improves system maintainability by using a single programming language. The system presented requires significantly less technical expertise to instantiate than the instrumentation of previous systems, yet integrity of performance is retained and demonstrated with experimental data.

  14. Instrumentation and control of harmonic oscillators via a single-board microprocessor-FPGA device

    Science.gov (United States)

    Picone, Rico A. R.; Davis, Solomon; Devine, Cameron; Garbini, Joseph L.; Sidles, John A.

    2017-04-01

    We report the development of an instrumentation and control system instantiated on a microprocessor-field programmable gate array (FPGA) device for a harmonic oscillator comprising a portion of a magnetic resonance force microscope. The specific advantages of the system are that it minimizes computation, increases maintainability, and reduces the technical barrier required to enter the experimental field of magnetic resonance force microscopy. Heterodyne digital control and measurement yields computational advantages. A single microprocessor-FPGA device improves system maintainability by using a single programming language. The system presented requires significantly less technical expertise to instantiate than the instrumentation of previous systems, yet integrity of performance is retained and demonstrated with experimental data.

  15. Radiological assessment of placement of the hysteroscopically inserted Essure permanent birth control device.

    Science.gov (United States)

    Lorente Ramos, R M; Azpeitia Armán, J; Aparicio Rodríguez-Miñón, P; Salazar Arquero, F J; Albillos Merino, J C

    2015-01-01

    Essure is a permanent birth control device that is inserted through the cervix by hysteroscopy. The device is placed in the fallopian tubes, where it causes occlusion by stimulating fibrosis. Patients can be followed up with plain-film X-rays, hysterosalpingography, and ultrasonography, although the devices can also be identified incidentally on CT and MRI. The follow-up of Essure is based on checking the criteria for appropriate positioning and correct functioning (tubal occlusion) and on diagnosing complications. The most common complications are perforation, migration (toward the uterine or peritoneal cavity), and occlusion failure. In hysterosalpingography, vascular intravasation is the most common cause of diagnostic error. Radiologists need to know how to recognize the device on different imaging techniques, how to check that it is correctly placed and functioning, and how to diagnose complications. Copyright © 2014 SERAM. Published by Elsevier España, S.L.U. All rights reserved.

  16. Naproxen Sodium for Pain Control With Intrauterine Device Insertion: A Randomized Controlled Trial.

    Science.gov (United States)

    Ngo, Lynn L; Braaten, Kari P; Eichen, Eva; Fortin, Jennifer; Maurer, Rie; Goldberg, Alisa B

    2016-12-01

    To evaluate whether 550 mg oral naproxen sodium given 1 hour before intrauterine device (IUD) insertion is effective for pain relief as compared with placebo. This was a randomized, double-blind, placebo-controlled trial. The primary outcome was pain with IUD insertion measured on a 100-mm visual analog scale (VAS). Our sample size was calculated to detect a 15-mm difference in VAS scores with 80% power (α=0.05). Secondary outcomes included pain with tenaculum placement, uterine sounding, and 5 and 15 minutes postinsertion. A total of 118 women were enrolled and analyzed (58 in the naproxen sodium arm, 60 in the placebo arm, 97% nulliparous) between May 11, 2015, and March 25, 2016. There were no differences in baseline demographics or reproductive characteristics between arms. There were no differences in median VAS pain scores for the primary outcome of pain with IUD insertion between the naproxen sodium arm compared with the placebo arm (69 compared with 66 mm, P=.89). There were no differences in the secondary outcomes of median VAS pain scores with tenaculum placement (37 compared with 32 mm, P=.97) or uterine sounding (60 compared with 58 mm, P=.66). However, median pain scores postprocedure were lower in the naproxen arm as compared with the placebo arm: 17 compared with 26 mm (P=.01) at 5 minutes and 13 compared with 24 mm (P=.01) at 15 minutes postinsertion. Oral naproxen sodium does not reduce pain with IUD insertion but does reduce pain after insertion and should be considered as a premedication. ClinicalTrials.gov, http://clinicaltrials.gov, NCT02388191.

  17. PANATIKI: a network access control implementation based on PANA for IoT devices.

    Science.gov (United States)

    Moreno Sanchez, Pedro; Marin Lopez, Rafa; Gomez Skarmeta, Antonio F

    2013-11-01

    Internet of Things (IoT) networks are the pillar of recent novel scenarios, such as smart cities or e-healthcare applications. Among other challenges, these networks cover the deployment and interaction of small devices with constrained capabilities and Internet protocol (IP)-based networking connectivity. These constrained devices usually require connection to the Internet to exchange information (e.g., management or sensing data) or access network services. However, only authenticated and authorized devices can, in general, establish this connection. The so-called authentication, authorization and accounting (AAA) services are in charge of performing these tasks on the Internet. Thus, it is necessary to deploy protocols that allow constrained devices to verify their credentials against AAA infrastructures. The Protocol for Carrying Authentication for Network Access (PANA) has been standardized by the Internet engineering task force (IETF) to carry the Extensible Authentication Protocol (EAP), which provides flexible authentication upon the presence of AAA. To the best of our knowledge, this paper is the first deep study of the feasibility of EAP/PANA for network access control in constrained devices. We provide light-weight versions and implementations of these protocols to fit them into constrained devices. These versions have been designed to reduce the impact in standard specifications. The goal of this work is two-fold: (1) to demonstrate the feasibility of EAP/PANA in IoT devices; (2) to provide the scientific community with the first light-weight interoperable implementation of EAP/PANA for constrained devices in the Contiki operating system (Contiki OS), called PANATIKI. The paper also shows a testbed, simulations and experimental results obtained from real and simulated constrained devices.

  18. PANATIKI: A Network Access Control Implementation Based on PANA for IoT Devices

    Directory of Open Access Journals (Sweden)

    Antonio F. Gomez Skarmeta

    2013-11-01

    Full Text Available Internet of Things (IoT networks are the pillar of recent novel scenarios, such as smart cities or e-healthcare applications. Among other challenges, these networks cover the deployment and interaction of small devices with constrained capabilities and Internet protocol (IP-based networking connectivity. These constrained devices usually require connection to the Internet to exchange information (e.g., management or sensing data or access network services. However, only authenticated and authorized devices can, in general, establish this connection. The so-called authentication, authorization and accounting (AAA services are in charge of performing these tasks on the Internet. Thus, it is necessary to deploy protocols that allow constrained devices to verify their credentials against AAA infrastructures. The Protocol for Carrying Authentication for Network Access (PANA has been standardized by the Internet engineering task force (IETF to carry the Extensible Authentication Protocol (EAP, which provides flexible authentication upon the presence of AAA. To the best of our knowledge, this paper is the first deep study of the feasibility of EAP/PANA for network access control in constrained devices. We provide light-weight versions and implementations of these protocols to fit them into constrained devices. These versions have been designed to reduce the impact in standard specifications. The goal of this work is two-fold: (1 to demonstrate the feasibility of EAP/PANA in IoT devices; (2 to provide the scientific community with the first light-weight interoperable implementation of EAP/PANA for constrained devices in the Contiki operating system (Contiki OS, called PANATIKI. The paper also shows a testbed, simulations and experimental results obtained from real and simulated constrained devices.

  19. Nanoscale architectural tuning of parylene patch devices to control therapeutic release rates

    Science.gov (United States)

    Pierstorff, Erik; Lam, Robert; Ho, Dean

    2008-11-01

    The advent of therapeutic functionalized implant coatings has significantly impacted the medical device field by enabling prolonged device functionality for enhanced patient treatment. Incorporation of drug release from a stable, biocompatible surface is instrumental in decreasing systemic application of toxic therapeutics and increasing the lifespan of implants by the incorporation of antibiotics and anti-inflammatories. In this study, we have developed a parylene C-based device for controlled release of Doxorubicin, an anti-cancer chemotherapy and definitive read-out for preserved drug functionality, and further characterized the parylene deposition condition-dependent tunability of drug release. Drug release is controlled by the deposition of a layer of 20-200 nm thick parylene over the drug layer. This places a porous layer above the Doxorubicin, limiting drug elution based on drug accessibility to solvent and the solvent used. An increase in the thickness of the porous top layer prolongs the elution of active drug from the device from, in the conditions tested, the order of 10 min to the order of 2 d in water and from the order of 10 min to no elution in PBS. Thus, the controlled release of an anti-cancer therapeutic has been achieved via scalably fabricated, parylene C-encapsulated drug delivery devices.

  20. Brain Computer Interface-Controlling Devices Utilizing The Alpha Brain Waves

    Directory of Open Access Journals (Sweden)

    Rohan Hundia

    2015-01-01

    Full Text Available Abstract This paper describes the development and testing of an interface system whereby one can control external devices by voluntarily controlling alpha waves that is through eye movement. Such a system may be used for the control of prosthetics robotic arms and external devices like wheelchairs using the alpha brain waves and the Mu rhythm. The response generated through the movement of the eye detecting and controlling the amplitude of the alpha brain waves is interfaced and processed to control Robotic systems and smart home control. In order to measure the response of alpha waves over different lobes of the brain initially I measured these signals over 32 regions using silver chloride plated electrodes. By the opening and the closure of the eyes and the movement in the up-down left-right directions and processing these movements measuring them over the occipital region I was able to differentiate the amplitude of the alpha waves generated due to these several movements. In the First session testing period subjects were asked to close and open their eyes and they were able to control limited movements of a Robot and a prosthetic arm. In the Second 2session the movement of the eyes was also considered left-right up-down along with the opening and closure during this time span they were able to control more dimensions of the robot several devices at the same time using different eye movements.

  1. An optimal controller for an electric ventricular-assist device: theory, implementation, and testing

    Science.gov (United States)

    Klute, G. K.; Tasch, U.; Geselowitz, D. B.

    1992-01-01

    This paper addresses the development and testing of an optimal position feedback controller for the Penn State electric ventricular-assist device (EVAD). The control law is designed to minimize the expected value of the EVAD's power consumption for a targeted patient population. The closed-loop control law is implemented on an Intel 8096 microprocessor and in vitro test runs show that this controller improves the EVAD's efficiency by 15-21%, when compared with the performance of the currently used feedforward control scheme.

  2. A prototype rehabilitation device with variable resistance and joint motion control

    Science.gov (United States)

    Dong, Shufang; Lu, Ke-Qian; Sun, J.Q.; Rudolph, Katherine

    2008-01-01

    Resistance exercise has been widely reported to have positive rehabilitation effects for patients with neuromuscular and orthopaedic conditions. This paper presents the design of a versatile rehabilitation device in the form of a rotating joint arm mounted on the adjustable seat that provides passive resistance during strength training for muscles. The resistance is supplied by a magnetorheological damper. Intelligent controls are developed to produce resistance force based on the prescription of the therapist. The device provides both isometric and isokinetic strength training and is reconfigurable for several human joints. Special consideration has been given to the human–machine interaction in the adaptive control algorithms that can modify the behavior of the device to account for strength gains or muscle fatigue. PMID:16112598

  3. TASER® Electronic Control Device-Induced Rhabdomyolysis and Renal Failure: A Case Report

    Science.gov (United States)

    Ahmad, Ibrahim

    2015-01-01

    Many law enforcement agencies around the United States are employing the use of TASER® electronic control devices (TASER® International Inc.) to subdue combative suspects. Since its inception the TASER® has had a temporal association with reports of rhabdomyolysis. Case reports have reported TASER® induced rhabdomyolysis as mild but serious cases have also been reported. Herein we present the case of a single patient who was admitted to our health network with severe rhabdomyolysis after receiving TASER® shocks and review the pertinent literature. No direct link has been established between clinically significant rhabdomyolysis and TASER® device application but this case serves as an example of a sparsely documented but serious complication that may occur in patients who are at risk for restraint by an electronic control device. PMID:26557540

  4. TASER(®) Electronic Control Device-Induced Rhabdomyolysis and Renal Failure: A Case Report.

    Science.gov (United States)

    Gleason, James Benjamin; Ahmad, Ibrahim

    2015-10-01

    Many law enforcement agencies around the United States are employing the use of TASER(®) electronic control devices (TASER(®) International Inc.) to subdue combative suspects. Since its inception the TASER(®) has had a temporal association with reports of rhabdomyolysis. Case reports have reported TASER(®) induced rhabdomyolysis as mild but serious cases have also been reported. Herein we present the case of a single patient who was admitted to our health network with severe rhabdomyolysis after receiving TASER(®) shocks and review the pertinent literature. No direct link has been established between clinically significant rhabdomyolysis and TASER(®) device application but this case serves as an example of a sparsely documented but serious complication that may occur in patients who are at risk for restraint by an electronic control device.

  5. Improvement on Main/backup Controller Switching Device of the Nozzle Throat Area Control System for a Turbofan Aero Engine

    Science.gov (United States)

    Li, Jie; Duan, Minghu; Yan, Maode; Li, Gang; Li, Xiaohui

    2014-06-01

    A full authority digital electronic controller (FADEC) equipped with a full authority hydro-mechanical backup controller (FAHMBC) is adopted as the nozzle throat area control system (NTACS) of a turbofan aero engine. In order to ensure the switching reliability of the main/backup controller, the nozzle throat area control switching valve was improved from three-way convex desktop slide valve to six-way convex desktop slide valve. Simulation results show that, if malfunctions of FAEDC occur and abnormal signals are outputted from FADEC, NTACS will be seriously influenced by the main/backup controller switching in several working states, while NTACS will not be influenced by using the improved nozzle throat area control switching valve, thus the controller switching process will become safer and smoother and the working reliability of this turbofan aero engine is improved by the controller switching device improvement.

  6. A perineal protection device designed to protect the perineum during labor: a multicenter randomized controlled trial.

    Science.gov (United States)

    Lavesson, Tony; Griph, Inger D; Skärvad, Anna; Karlsson, Ann-Sofi; Nilsson, Helen B; Steinvall, Margareta; Haadem, Knut

    2014-10-01

    The objective of this study was to evaluate the protective effects of a new device for reducing perineal tears during vaginal childbirth. A multicenter open randomized controlled trial (RCT) was performed in Helsingborg, Lund and Malmö, Sweden consisting of 1148 women. Women anticipating a vaginal delivery were either randomized to the intervention group (n=574 in which the perineal protection device was used, or a control group (n=574), in which the perineal protection device was not used. The main outcome measurements were incidence of vaginal and perineal tears (1st to 4th degree tears) and adverse effects on the parturient and newborn. The incidences of first- and second-degree tears of the vagina (p=0.018) and perineum (p=0.005) were significantly reduced in the intervention group compared with the controls. In the intervention- and control group, 184 women (34.9%) and 142 (26.6%) showed no perineal tearing, respectively (p=0.034). Numbers needed to treat to avoid any perianal tearing was 12. The incidence of anal sphincter rupture (ASR) was the same in both groups (n=19; 3.4%). No negative effects on mother or child from using the device were observed. The perineal protective device significantly reduced the incidence of first- and second-degree tears in the vagina and perineum during vaginal birth and also significantly increased the number of parturients with a fully intact posterior commissure. No significant reduction of ASR and no negative effects of the device were observed. Copyright © 2014 The Authors. Published by Elsevier Ireland Ltd.. All rights reserved.

  7. Testing of monitoring devices for JP-4 releases in the subsurface. Final report, 1 Sep 88-30 Apr 90

    Energy Technology Data Exchange (ETDEWEB)

    Wickramanayke, G.B.; Kittel, J.A.; Hinchee, R.E.; Voudrias, E.A.; Reichenbach, N.G.

    1990-04-01

    This research sought to select and test the performance of a set of external monitoring devices having potential application for both underground storage tanks (USTs) and general subsurface monitoring. These devices may be used to detect and/or monitor jet fuel in the subsurface from leaking USTs or other sources. Seven devices were tested for both vapor-phase and liquid-phase monitoring of JP-4 jet fuel. Cylindrical tanks 12' diam. and 4' deep containing a uniform sand were used as test beds. A release that averaged less than 0.02 gal/hr of JP-4 was simulated at the central location of the sand test beds. Gas chromatography analysis was used to determine actual concentrations for comparison to device response. Fresh JP-4 was released into dry sand and moist sand to simulate vadose zone monitoring. JP-4 was also released into a test bed with a static water table to simulate a leak contaminating the groundwater. Measurement of floating fuel thickness was determined throughout the liquid phase experiments, as well as liquid and vapor hydrocarbon concentrations. Devices were tested for false positives. The rapid vapor concentration rise that occurs during a leak indicates that vapor-phase monitoring is an excellent method for early warning of product release. Devices using vapor phase detection for leaking JP-4 had the best overall performance. Devices monitoring for JP-4 floating product on the water table are not as quick or sensitive as the vapor phase devices at detecting a leak.

  8. Fiber-optic, anti-cycling, high pressure sodium street light control. Final technical progress report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-05-01

    This is the Final Technical Progress Report on a project to develop and market a Fiber-Optic Anti-Cycling High Pressure Sodium Street Light Control. The field test units are now being made with a single vertical PC board design and contains a computer-on-a-chip or PROM IC to take the place of the majority of the components previously contained on the upper logic board. This will reduce the final costs of the unit when it is in production and increase the control`s flexibility. The authors have finished the soft tooling and have made the 400 plastic cases for the field test units. The new configuration of the cases entails a simplified design of the control shell which will have the lenses cast in place. The shell and base plastics are now finished and in final assembly awaiting the completion of the PC boards.

  9. Hands-free device control using sound picked up in the ear canal

    Science.gov (United States)

    Chhatpar, Siddharth R.; Ngia, Lester; Vlach, Chris; Lin, Dong; Birkhimer, Craig; Juneja, Amit; Pruthi, Tarun; Hoffman, Orin; Lewis, Tristan

    2008-04-01

    Hands-free control of unmanned ground vehicles is essential for soldiers, bomb disposal squads, and first responders. Having their hands free for other equipment and tasks allows them to be safer and more mobile. Currently, the most successful hands-free control devices are speech-command based. However, these devices use external microphones, and in field environments, e.g., war zones and fire sites, their performance suffers because of loud ambient noise: typically above 90dBA. This paper describes the development of technology using the ear as an output source that can provide excellent command recognition accuracy even in noisy environments. Instead of picking up speech radiating from the mouth, this technology detects speech transmitted internally through the ear canal. Discreet tongue movements also create air pressure changes within the ear canal, and can be used for stealth control. A patented earpiece was developed with a microphone pointed into the ear canal that captures these signals generated by tongue movements and speech. The signals are transmitted from the earpiece to an Ultra-Mobile Personal Computer (UMPC) through a wired connection. The UMPC processes the signals and utilizes them for device control. The processing can include command recognition, ambient noise cancellation, acoustic echo cancellation, and speech equalization. Successful control of an iRobot PackBot has been demonstrated with both speech (13 discrete commands) and tongue (5 discrete commands) signals. In preliminary tests, command recognition accuracy was 95% with speech control and 85% with tongue control.

  10. O dispositivo de gozo na sociedade do controle The device of enjoyment in the society of control

    Directory of Open Access Journals (Sweden)

    Leonardo José Barreira Danziato

    2010-12-01

    Full Text Available A partir das proposições de Foucault sobre uma mudança de dispositivos na modernidade, saindo de um "dispositivo de aliança" para um "dispositivo da sexualidade", e levando em conta, ainda, as considerações de Deleuze sobre a contemporânea "sociedade do controle", o autor realiza uma leitura psicanalítica dessas transformações nos processos de subjetivação modernos e contemporâneos, propondo a regência de um novo dispositivo na atualidade, que denomina de "dispositivo de gozo". Argumenta em favor das suas leituras a capitalização do "mais-de-gozar" sugerida por Lacan, e os imperativos de gozo próprios dos nossos tempos.From the propositions of Foucault on a change of devices in modernity, leaving a "alliance device" to a "sexual device", and also taking into account the considerations of Deleuze on the contemporary "society of control," the author presents a psychoanalytic reading of these changes in the processes of modern and contemporary subjectivation, proposing the regency of a new device today, which he called "enjoyment device." He argues in favor of his readings the capitalization of the plus de goce suggested by Lacan, and the imperatives of enjoyment of our own times.

  11. Characterization and Erosion Modeling of a Nozzle-Based Inflow-Control Device

    DEFF Research Database (Denmark)

    Olsen, Jógvan Juul; Hemmingsen, Casper Schytte; Bergmann, Line

    2017-01-01

    In the petroleum industry, water-and-gas breakthrough in hydrocarbon reservoirs is a common issue that eventually leads to uneconomic production. To extend the economic production lifetime, inflow-control devices (ICDs) are designed to delay the water-and-gas breakthrough. Because the lifetime of...

  12. Temperature influence on electrically controlled liquid crystal filled photonic bandgap fiber devices

    DEFF Research Database (Denmark)

    Wei, Lei; Alkeskjold, Thomas Tanggaard; Bjarklev, Anders Overgaard

    2009-01-01

    We experimentally investigate the temperature influence on electrically controlled liquid crystal filled photonic bandgap fiber device. The phase shift in the wavelength range 1520nm-1600nm for realizing quarter and half wave plates at different temperatures by applying a certain voltage...

  13. Photolithography of thick photoresist coating for electrically controlled liquid crystal photonic bandgap fibre devices

    DEFF Research Database (Denmark)

    Wei, Lei; Khomtchenko, Elena; Alkeskjold, Thomas Tanggaard

    2009-01-01

    Thick photoresist coating for electrode patterning in an anisotropically etched V-groove is investigated for electrically controlled liquid crystal photonic bandgap fibre devices. The photoresist step coverage at the convex corners is compared with and without soft baking after photoresist spin...

  14. Load power device, system and method of load control and management employing load identification

    Energy Technology Data Exchange (ETDEWEB)

    Yang, Yi; Luebke, Charles John; Schoepf, Thomas J.

    2018-01-09

    A load power device includes a power input, at least one power output for at least one load, a plurality of sensors structured to sense voltage and current at the at least one power output, and a processor. The processor provides: (a) load identification based upon the sensed voltage and current, and (b) load control and management based upon the load identification.

  15. Research of energy efficiency evaluation parameters for power quality control device based on IGBT module

    Science.gov (United States)

    Xu, Jieyan; Liu, Yang; Mao, Yongqiu; Chen, Zheng; Jia, Rongda; Zhao, Caiyi; Yang, Xi

    2017-01-01

    In this paper, the energy efficiency evaluation parameters for power quality control device based on IGBT modules have been discussed. First of all, energy consumption of the typical power quality control equipment, such as SVG, APF and MEC, under the rated conditions, have been analyzed to identify the main energy-consuming parts. Then, energy loss mechanism and energy saving path of IGBT module have been discussed. And the energy saving improvement direction of the power quality control equipment based on IGBT module is identified at the same time. At last, the applicable energy efficiency evaluation parameters for power quality control device have been selected, based on the research of the product performances for energy efficiency of power grid.

  16. Physical assistance devices in complex motor skill learning: benefits of a self-controlled practice schedule.

    Science.gov (United States)

    Wulf, G; Toole, T

    1999-09-01

    This study examines the effects of a self-controlled use of physical assistance devices on learning a complex motor skill (i.e., producing slalom-type movements on a ski simulator). Physical assistance was provided by ski poles. One group of learners (self-control) was provided with the poles whenever they requested them, whereas another (yoked) group had no influence on the pole/no-pole schedule. While there were no group differences during the practice phase (Days 1 and 2), clear group differences emerged in the retention test without poles (Day 3). The self-control group produced significantly larger amplitudes than the yoked group. These results extend previous findings by showing learning advantages of the self-controlled use of physical assistance devices in complex motor skill learning.

  17. Quantifying opportunities for hospital cost control: medical device purchasing and patient discharge planning.

    Science.gov (United States)

    Robinson, James C; Brown, Timothy T

    2014-09-01

    To quantify the potential reduction in hospital costs from adoption of best local practices in supply chain management and discharge planning. We performed multivariate statistical analyses of the association between total variable cost per procedure and medical device price and length of stay, controlling for patient and hospital characteristics. Ten hospitals in 1 major metropolitan area supplied patient-level administrative data on 9778 patients undergoing joint replacement, spine fusion, or cardiac rhythm management (CRM) procedures in 2008 and 2010. The impact on each hospital of matching lowest local market device prices and lowest patient length of stay (LOS) was calculated using multivariate regression analysis controlling for patient demographics, diagnoses, comorbidities, and implications. Average variable costs ranged from $11,315 for joint replacement to $16,087 for CRM and $18,413 for spine fusion. Implantable medical devices accounted for a large share of each procedure's variable costs: 44% for joint replacement, 39% for spine fusion, and 59% for CRM. Device prices and patient length-of-stay exhibited wide variation across hospitals. Total potential hospital cost savings from achieving best local practices in device prices and patient length of stay are 14.5% for joint replacement, 18.8% for spine fusion;,and 29.1% for CRM. Hospitals have opportunities for cost reduction from adoption of best local practices in supply chain management and discharge planning.

  18. 40 CFR 63.3166 - How do I determine the add-on control device emission destruction or removal efficiency?

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 12 2010-07-01 2010-07-01 true How do I determine the add-on control... Limitations § 63.3166 How do I determine the add-on control device emission destruction or removal efficiency? You must use the procedures and test methods in this section to determine the add-on control device...

  19. 40 CFR 63.9323 - How do I determine the add-on control device emission destruction or removal efficiency?

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 14 2010-07-01 2010-07-01 false How do I determine the add-on control... determine the add-on control device emission destruction or removal efficiency? You must use the procedures and test methods in this section to determine the add-on control device emission destruction or...

  20. 40 CFR 63.4362 - How do I determine the add-on control device emission destruction or removal efficiency?

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 12 2010-07-01 2010-07-01 true How do I determine the add-on control... § 63.4362 How do I determine the add-on control device emission destruction or removal efficiency? You must use the procedures and test methods in this section to determine the add-on control device...

  1. Secure Reprogramming of a Network Connected Device : Securing programmable logic controllers

    OpenAIRE

    Tesfaye, Mussie

    2012-01-01

    This is a master’s thesis project entitled “Secure reprogramming of network connected devices”. The thesis begins by providing some background information to enable the reader to understand the current vulnerabilities of network-connected devices, specifically with regard to cyber security and data integrity. Today supervisory control and data acquisition systems utilizing network connected programmable logic controllers are widely used in many industries and critical infrastructures. These n...

  2. Bismuth, antimony and tellurium alloy nanoparticles with controllable shape and composition for efficient thermoelectric devices

    Energy Technology Data Exchange (ETDEWEB)

    Mott, Derrick; Mai, Nguyen T.; Thuy, Nguyen T.B.; Maeda, Youjiro; Linh, Tran P.T.; Koyano, Mikio; Maenosono, Shinya [School of Materials Science, Japan Advanced Institute of Science and Technology, 1-1 Asahidai, Nomi, Ishikawa 923-1292 (Japan)

    2011-01-15

    The wet chemical synthesis of organic molecule encapsulated Bi{sub x}Sb{sub y}Te{sub 100-x-y} nanoparticles (NPs) has been demonstrated to be shape and composition controllable as a function of the organic capping species used, the particles serve as intriguing materials towards thermoelectric (TE) devices with enhanced and controllable activity. (Copyright copyright 2011 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  3. METHODS AND DEVICES FOR CONTROL OF OPEN MICROSCOPIC POROSITY OF PORCELAIN INSULATORS

    OpenAIRE

    Galagan, Roman

    2014-01-01

    Examined the methods and devices of control of porcelain insulators for presence of defects such as open microscopic porosity. It is shown that open microscopic porosity is the most dangerous defect production origin and is responsible for over 80% of failures of porcelain support insulators. Considered methods of control are divided into two groups: destructive and non-destructive. For each method are highlighted their advantages and disadvantages. The analysis showed that most of the existi...

  4. Surface EMG and intra-socket force measurement to control a prosthetic device

    Science.gov (United States)

    Sanford, Joe; Patterson, Rita; Popa, Dan

    2015-06-01

    Surface electromyography (SEMG) has been shown to be a robust and reliable interaction method allowing for basic control of powered prosthetic devices. Research has shown a marked decrease in EMG-classification efficiency throughout activities of daily life due to socket shift and movement and fatigue as well as changes in degree of fit of the socket throughout the subject's lifetime. Users with the most severe levels of amputation require the most complex devices with the greatest number of degrees of freedom. Controlling complex dexterous devices with limited available inputs requires the addition of sensing and interaction modalities. However, the larger the amputation severity, the fewer viable SEMG sites are available as control inputs. Previous work reported the use of intra-socket pressure, as measured during wrist flexion and extension, and has shown that it is possible to control a powered prosthetic device with pressure sensors. In this paper, we present data correlations of SEMG data with intra-socket pressure data. Surface EMG sensors and force sensors were housed within a simulated prosthetic cuff fit to a healthy-limbed subject. EMG and intra-socket force data was collected from inside the cuff as a subject performed pre-defined grip motions with their dominant hand. Data fusion algorithms were explored and allowed a subject to use both intra-socket pressure and SEMG data as control inputs for a powered prosthetic device. This additional input modality allows for an improvement in input classification as well as information regarding socket fit through out activities of daily life.

  5. Active Thermal Control for Reliability Improvement of MOS-gated Power Devices

    DEFF Research Database (Denmark)

    Soldati, Alessandro; Concari, Carlo; Dossena, Fabrizio

    2017-01-01

    This paper proposes an Active Thermal Control (ATC) method for MOS-gated power switches aimed at reducing temperature swing amplitude during operation. It leverages on the fact that thermal cycle amplitude of many actuation system components (such as power devices) has a large impact on the system...... reliability and lifetime. These figures can then be improved, which eases the adoption of electrification in markets, such as transportation, where they are still below target values. The proposed ATC method leaves electric load parameters untouched, while acting dynamically on gate parameters, namely voltage...... and resistance. A model-predictive control (MPC) strategy is used to determine the most suitable parameters to use. Simulations of the control scheme are presented first, to predict the potential benefits on temperature swing amplitude, and the consequent improvements in terms of device lifetime are inferred...

  6. Hierarchical Brokering with Feedback Control Framework in Mobile Device-Centric Clouds

    Directory of Open Access Journals (Sweden)

    Chao-Lieh Chen

    2016-01-01

    Full Text Available We propose a hierarchical brokering architecture (HiBA and Mobile Multicloud Networking (MMCN feedback control framework for mobile device-centric cloud (MDC2 computing. Exploiting the MMCN framework and RESTful web-based interconnection, each tier broker probes resource state of its federation for control and management. Real-time and seamless services were developed. Case studies including intrafederation energy-aware balancing based on fuzzy feedback control and higher tier load balancing are further demonstrated to show how HiBA with MMCN relieves the embedding of algorithms when developing services. Theoretical performance model and real-world experiments both show that an MDC2 based on HiBA features better quality in terms of resource availability and network latency if it federates devices with enough resources distributed in lower tier hierarchy. The proposed HiBA realizes a development platform for MDC2 computing which is a feasible solution to User-Centric Networks (UCNs.

  7. COMPUTER CONTROLLED EXPERIMENTAL DEVICE FOR INVESTIGATIONS OF TRIBOLOGICAL INFLUENCES IN SHEET METAL FORMING

    Directory of Open Access Journals (Sweden)

    Tomislav Vujinović

    2012-05-01

    Full Text Available Sheet metal forming, especially deep drawing process is influenced by many factors. Blank holding force and drawbead displacement are two of them that can be controlled during the forming process.For this purpose, an electro-hydraulic computerized sheet-metal strip sliding device has been constructed. The basic characteristic of this device is realization of variable contact pressure and drawbead height as functions of time or stripe displacement. There are both, pressure and drawbead, ten linear and nonlinear functions. Additional features consist of the ability to measure drawing force, contact pressure, drawbead displacement etc.The device overview and first results of steel sheet stripe sliding over rounded drawbead are presented in the paper.

  8. Computer controlled experimental device for investigations of tribological influences in sheet metal forming

    Directory of Open Access Journals (Sweden)

    Milan Djordjevic

    2012-05-01

    Full Text Available Sheet metal forming, especially deep drawing process, is influenced by many factors. Blank holding force and drawbead displacement are two of them that can be controlled during the forming process. For this purpose, electro-hydraulic computerized sheet-metal strip sliding device has been constructed. Basic characteristic of this device is realization of variable contact pressure and drawbead height as functions of time or stripe displacement. There are both, pressure and drawbead, ten linear and nonlinear functions. Additional features consist of the ability to measure drawing force, contact pressure, drawbead displacement etc. Presented in the paper are the device overview and the first results of steel sheet stripe sliding over rounded  drawbead.

  9. Influences of Removable Devices on the Anti-Threat Model: Dynamic Analysis and Control Strategies

    Directory of Open Access Journals (Sweden)

    Jinhua Ma

    2015-08-01

    Full Text Available With the rapid development of M2M wireless network, damages caused by malicious worms are getting more and more serious. The main goal of this paper is to explore the influences of removable devices on the interaction dynamics between malicious worms and benign worms by using a mathematical model. The model takes two important network environment factors into consideration: benign worms and the influences of removable devices. Besides, the model’s basic reproduction number is obtained, along with the correct control conditions of the local and global asymptotical stability of the worm-free equilibrium. Simulation results show that the effectiveness of our proposed model in terms of reflecting the influences of removable devices on the interaction dynamics of an anti-treat model. Based on numerical analyses and simulations, effective methods are proposed to contain the propagation of malicious worms by using anti-worms.

  10. Method of controlling illumination device based on current-voltage model

    DEFF Research Database (Denmark)

    2013-01-01

    across and current through the LED and the means for generating the activation signal is adapted to generate the activating signal based on the voltage, the current and a current- voltage model related to LED. The current-voltage model defines a relationship between the current, the voltage......The present invention relates to an illumination device comprising a number of LEDs, means for receiving an input signal, means for generating an activation signal for at least one of the LEDs based on the input signal. The illumination device comprises further means for obtaining the voltage...... and the colorimetric properties of said light emitted by LED. The present invention relates also to a method of controlling and a meted of calibrating such illumination device....

  11. Controlling light with light using coherent meta-devices: all-optical transistor, summator and invertor

    CERN Document Server

    Fang, Xu; Zheludev, Nikolay I

    2014-01-01

    Vast amounts of information are conveyed by photons in optical fibres, but most data processing is performed electronically, creating the infamous 'information bottleneck' and consuming energy at an increasingly unsustainable rate. The potential for photonic devices to manipulate light themselves remains unfulfilled, largely due to the absence of materials with strong, fast optical nonlinearities. Here we show that small-signal amplifier, summator and invertor functions for optical signals may all be realized with a 4-port device exploiting the coherent interaction of beams on a planar plasmonic metamaterial, assuming no intrinsic nonlinearity. We show that coherently controlled redistribution of energy among ports can deliver various forms of optical switching. Such devices can operate even at the single photon level, with THz bandwidth, and without introducing signal distortion, presenting powerful opportunities for novel optical data processing architectures, complexity oracles and the locally coherent net...

  12. PREFACE: Atomically controlled fabrication technology: new physics and functional device realization Atomically controlled fabrication technology: new physics and functional device realization

    Science.gov (United States)

    Kuwahara, Yuji; Kasai, Hideaki

    2011-10-01

    To realize next generation functional devices, atomic level controllability of the application and fabrication techniques is necessary. The conventional route to advance solid state devices, which involves improvement of 'instrumental accuracy', is now facing a major paradigm shift towards 'phenomenal accuracy'. Therefore, to keep up with this critical turn in the development of devices, pioneering research (both theoretical and experimental) on relevant materials, focusing on new physics at the atomic scale, is inevitable. This special section contains articles on the advancements in fabrication of functional devices with an emphasis on the exploration, clarification and understanding of atomistic phenomena. Research articles reporting theoretical and experimental findings on various materials such as semiconductors, metals, magnetic and organic systems, collectively present and 'capture' the appropriate processes and mechanisms of this rapidly developing field. The theoretical investigations employ first-principles quantum-mechanical simulations to clarify and bring about design principles and guidelines, or to develop more reliable computational methods. Experimental studies, on the other hand, introduce novel capabilities to build, view and manipulate materials at the atomic scale by employing pioneering techniques. Thus, the section pays significant attention to novel structures and properties and the accompanying fabrication techniques and design arising from the understanding of properties and structures at the atomic scale. We hope that researchers in the area of physics, materials science and engineering, interested in the development of functional devices via atomic level control, will find valuable information in this collaborative work. We are grateful to all of the authors for their contributions. Atomically controlled fabrication contents On the mechanism of carbon nanotube formation: the role of the catalyst G N Ayre, T Uchino, B Mazumder, A L Hector

  13. Monolithically integrated Si gate-controlled light-emitting device: science and properties

    Science.gov (United States)

    Xu, Kaikai

    2018-02-01

    The motivation of this study is to develop a p–n junction based light emitting device, in which the light emission is conventionally realized using reverse current driving, by voltage driving. By introducing an additional terminal of insulated gate for voltage driving, a novel three-terminal Si light emitting device is described where both the light intensity and spatial light pattern of the device are controlled by the gate voltage. The proposed light emitting device employs injection-enhanced Si in avalanche mode where electric field confinement occurs in the corner of a reverse-biased p+n junction. It is found that, depending on the bias conditions, the light intensity is either a linear or a quadratic function of the applied gate voltage or the reverse-bias. Since the light emission is based on the avalanching mode, the Si light emitting device offers the potential for very large scale integration-compatible light emitters for inter- or intra-chip signal transmission and contactless functional testing of wafers.

  14. Controlled Fabrication and High-Resolution Imaging of Molecular-Scale Three-Terminal Devices

    Science.gov (United States)

    Strachan, Douglas R.; Johnston, Danvers E.; Guiton, Beth S.; Park, T.-H.; Therien, M. J.; Davies, Peter K.; Bonnell, Dawn A.; Johnson, A. T. Charlie

    2007-03-01

    One of the biggest challenges to developing molecular-scale three terminal devices is to precisely fabricate and monitor the formation of the nanometer-scale electrodes (nanogaps). Recently, electromigrated nanogaps have been developed which provide sufficient gate-coupling to produce such devices. We have developed a technique for forming electromigrated nanogaps in a transmission electron microscope (TEM) in order to monitor their formation with high-resolution imaging in real time. The technique relies on computer-controlled electromigration using feedback to produce the nanogaps at room temperature. This TEM imaging allows us to monitor the dynamics of the device evolution, where the gaps remain ordered and clear of residue during the process. Using this technique, we find clear visual evidence for the importance of joule heating in the formation of electromigrated nanogaps. These electrodes can also be directly used in the construction of three terminal nanometer-scale devices. Our results have implications on the development of a wide range of novel molecular-scale devices. This work was supported by the National Science Foundation (NIRT Grant No. 0304531 and MRSEC award DMR05-20020).

  15. Design of a novel mobility device controlled by the feet motion of a standing child.

    Science.gov (United States)

    Schoepflin, Zachary R; Chen, Xi; Ragonesi, Christina B; Galloway, James C; Agrawal, Sunil K

    2011-01-01

    Self-generated mobility is a major contributor to the physical, emotional, cognitive, and social development of infants and toddlers. When young children have disorders that hinder self locomotion, their development is at risk for delay. Independent mobility via traditional power mobility devices may prevent this delay, but do little to encourage the child's development of gross motor skills. This research aims to develop a bio-driven mobile-assistive device that is controlled and driven by moving the feet, which may encourage the development of gross motor skills. In this study, system feasibility is shown by experiments on five typically developing toddlers and one special needs toddler with spastic cerebral palsy. Children were placed in the bio-driven device and instructed to navigate through a maze. All subjects were able to successfully complete the maze in multiple trials. Additionally, two toddlers showed evidence of improved driving skill by completing the maze in shorter times in successive trials on a given testing day. The results suggest that such a device is feasible for purposeful driving. Recommendations are given for the device and protocol redesign for related future testing. © 2011 IEEE

  16. Controlled delivery of antiangiogenic drug to human eye tissue using a MEMS device

    KAUST Repository

    Pirmoradi, Fatemeh Nazly

    2013-01-01

    We demonstrate an implantable MEMS drug delivery device to conduct controlled and on-demand, ex vivo drug transport to human eye tissue. Remotely operated drug delivery to human post-mortem eyes was performed via a MEMS device. The developed curved packaging cover conforms to the eyeball thereby preventing the eye tissue from contacting the actuating membrane. By pulsed operation of the device, using an externally applied magnetic field, the drug released from the device accumulates in a cavity adjacent to the tissue. As such, docetaxel (DTX), an antiangiogenic drug, diffuses through the eye tissue, from sclera and choroid to retina. DTX uptake by sclera and choroid were measured to be 1.93±0.66 and 7.24±0.37 μg/g tissue, respectively, after two hours in pulsed operation mode (10s on/off cycles) at 23°C. During this period, a total amount of 192 ng DTX diffused into the exposed tissue. This MEMS device shows great potential for the treatment of ocular posterior segment diseases such as diabetic retinopathy by introducing a novel way of drug administration to the eye. © 2013 IEEE.

  17. Taking SiC Power Devices to the Final Frontier: Addressing Challenges of the Space Radiation Environment

    Science.gov (United States)

    Lauenstein, Jean-Marie; Casey, Megan

    2017-01-01

    Silicon carbide power device technology has the potential to enable a new generation of aerospace power systems that demand high efficiency, rapid switching, and reduced mass and volume in order to expand space-based capabilities. For this potential to be realized, SiC devices must be capable of withstanding the harsh space radiation environment. Commercial SiC components exhibit high tolerance to total ionizing dose but to date, have not performed well under exposure to heavy ion radiation representative of the on-orbit galactic cosmic rays. Insertion of SiC power device technology into space applications to achieve breakthrough performance gains will require intentional development of components hardened to the effects of these highly-energetic heavy ions. This work presents heavy-ion test data obtained by the authors over the past several years for discrete SiC power MOSFETs, JFETs, and diodes in order to increase the body of knowledge and understanding that will facilitate hardening of this technology to space radiation effects. Specifically, heavy-ion irradiation data taken under different bias, temperature, and ion beam conditions is presented for devices from different manufacturers, and the emerging patterns discussed.

  18. Determination of Evaluative Devices for Adequate Assessment of Levels of Competence in Certain Physical Education Activities. Final Report.

    Science.gov (United States)

    Wilson, Ruth M.

    This investigation sought to study separately evaluative devices for assessing levels of performance and knowledge competency in basketball, swimming, and gymnastics. Subjects were women students at the University of Washington, 1968-69. For assessment of basketball competence, indications are that: (1) evaluation, by one individual, of films of…

  19. Development of regenerative peripheral nerve interfaces for motor control of neuroprosthetic devices

    Science.gov (United States)

    Kemp, Stephen W. P.; Urbanchek, Melanie G.; Irwin, Zachary T.; Chestek, Cynthia A.; Cederna, Paul S.

    2017-05-01

    Traumatic peripheral nerve injuries suffered during amputation commonly results in debilitating neuropathic pain in the affected limb. Modern prosthetic technologies allow for intuitive, simultaneous control of multiple degrees of freedom. However, these state-of-the-art devices require separate, independent control signals for each degree of freedom, which is currently not possible. As a result, amputees reject up to 75% of myoelectric devices preferring instead to use body-powered artificial limbs which offer subtle sensory feedback. Without meaningful and intuitive sensory feedback, even the most advanced myoelectric prostheses remain insensate, burdensome, and are associated with enormous cognitive demand and mental fatigue. The ideal prosthetic device is one which is capable of providing intuitive somatosensory feedback essential for interaction with the environment. Critical to the design of such a bioprosthetic device is the development of a reliable biologic interface between human and machine. This ideal patient-prosthetic interface allows for transmission of both afferent somatosensory information and efferent motor signals for a closed-loop feedback system of neural control. Our lab has developed the Regenerative Peripheral Nerve Interface (RPNI) as a biologic nerve interface designed for stable integration of a prosthetic device with transected peripheral nerves in a residual limb. The RPNI is constructed by surgically implanting the distal end of a transected peripheral nerve into an autogenous muscle graft. Animal experiments in our lab have shown recording of motor signals from RPNI's implanted into both rodents and monkeys. Here, we achieve high amplitude EMG signals with a high signal to noise (SNR) ratio.

  20. Energy-Efficient Scheduling for Hybrid Tasks in Control Devices for the Internet of Things

    Directory of Open Access Journals (Sweden)

    Guojun Dai

    2012-08-01

    Full Text Available In control devices for the Internet of Things (IoT, energy is one of the critical restriction factors. Dynamic voltage scaling (DVS has been proved to be an effective method for reducing the energy consumption of processors. This paper proposes an energy-efficient scheduling algorithm for IoT control devices with hard real-time control tasks (HRCTs and soft real-time tasks (SRTs. The main contribution of this paper includes two parts. First, it builds the Hybrid tasks with multi-subtasks of different function Weight (HoW task model for IoT control devices. HoW describes the structure of HRCTs and SRTs, and their properties, e.g., deadlines, execution time, preemption properties, and energy-saving goals, etc. Second, it presents the Hybrid Tasks’ Dynamic Voltage Scaling (HTDVS algorithm. HTDVS first sets the slowdown factors of subtasks while meeting the different real-time requirements of HRCTs and SRTs, and then dynamically reclaims, reserves, and reuses the slack time of the subtasks to meet their ideal energy-saving goals. Experimental results show HTDVS can reduce energy consumption about 10%–80% while meeting the real-time requirements of HRCTs, HRCTs help to reduce the deadline miss ratio (DMR of systems, and HTDVS has comparable performance with the greedy algorithm and is more favorable to keep the subtasks’ ideal speeds.

  1. Two neural network algorithms for designing optimal terminal controllers with open final time

    Science.gov (United States)

    Plumer, Edward S.

    1992-01-01

    Multilayer neural networks, trained by the backpropagation through time algorithm (BPTT), have been used successfully as state-feedback controllers for nonlinear terminal control problems. Current BPTT techniques, however, are not able to deal systematically with open final-time situations such as minimum-time problems. Two approaches which extend BPTT to open final-time problems are presented. In the first, a neural network learns a mapping from initial-state to time-to-go. In the second, the optimal number of steps for each trial run is found using a line-search. Both methods are derived using Lagrange multiplier techniques. This theoretical framework is used to demonstrate that the derived algorithms are direct extensions of forward/backward sweep methods used in N-stage optimal control. The two algorithms are tested on a Zermelo problem and the resulting trajectories compare favorably to optimal control results.

  2. ER fluid applications to vibration control devices and an adaptive neural-net controller

    Science.gov (United States)

    Morishita, Shin; Ura, Tamaki

    1993-07-01

    Four applications of electrorheological (ER) fluid to vibration control actuators and an adaptive neural-net control system suitable for the controller of ER actuators are described: a shock absorber system for automobiles, a squeeze film damper bearing for rotational machines, a dynamic damper for multidegree-of-freedom structures, and a vibration isolator. An adaptive neural-net control system composed of a forward model network for structural identification and a controller network is introduced for the control system of these ER actuators. As an example study of intelligent vibration control systems, an experiment was performed in which the ER dynamic damper was attached to a beam structure and controlled by the present neural-net controller so that the vibration in several modes of the beam was reduced with a single dynamic damper.

  3. 40 CFR Table 1 to Subpart Ssss of... - Operating Limits if Using Add-on Control Devices and Capture System

    Science.gov (United States)

    2010-07-01

    ... Using Add-on Control Devices and Capture System If you are required to comply with operating limits by... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Operating Limits if Using Add-on Control Devices and Capture System 1 Table 1 to Subpart SSSS of Part 63 Protection of Environment...

  4. 40 CFR Table 2 to Subpart Oooo of... - Operating Limits if Using Add-On Control Devices and Capture System

    Science.gov (United States)

    2010-07-01

    ... OOOO of Part 63—Operating Limits if Using Add-On Control Devices and Capture System If you are required... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Operating Limits if Using Add-On Control Devices and Capture System 2 Table 2 to Subpart OOOO of Part 63 Protection of Environment...

  5. 40 CFR Table 1 to Subpart Jjjj of... - Operating Limits if Using Add-On Control Devices and Capture System

    Science.gov (United States)

    2010-07-01

    ... Limits if Using Add-On Control Devices and Capture System If you are required to comply with operating... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Operating Limits if Using Add-On Control Devices and Capture System 1 Table 1 to Subpart JJJJ of Part 63 Protection of Environment...

  6. 77 FR 55500 - Controlled Substances: Final Adjusted Aggregate Production Quotas for 2012

    Science.gov (United States)

    2012-09-10

    ... for the estimated medical, scientific, research, and industrial needs of the United States, for export... to meet the current 2012 estimated medical, scientific, research, and industrial needs of the United... Enforcement Administration Controlled Substances: Final Adjusted Aggregate Production Quotas for 2012 AGENCY...

  7. FAST TRACK COMMUNICATION: Electrowetting-controlled droplet generation in a microfluidic flow-focusing device

    Science.gov (United States)

    Malloggi, Florent; Vanapalli, Siva A.; Gu, Hao; van den Ende, Dirk; Mugele, Frieder

    2007-11-01

    We studied the generation of aqueous microdrops in an oil-water flow-focusing device with integrated insulator-covered electrodes that allow for continuous tuning of the water wettability by means of electrowetting. Depending on the oil and water inlet pressures three different operating conditions were identified that shift upon applying a voltage: stable oil-water interface, drop generation, and laminar water jet formation. Full control over the drop generation is achieved within a well-defined range of inlet pressures, in quantitative agreement with a model based on the additive contributions from electrowetting and the local hydrostatic pressure at the junction. The tuning power of electrowetting is shown to increase upon device miniaturization, which makes this approach particularly attractive for flow control on the sub-micrometer scale.

  8. Microfluidic Device for Controllable Chemical Release via Field-Actuated Membrane Incorporating Nanoparticles

    Directory of Open Access Journals (Sweden)

    Xiang Wang

    2013-01-01

    Full Text Available We report a robust magnetic-membrane-based microfluidic platform for controllable chemical release. The magnetic membrane was prepared by mixing polydimethylsiloxane (PDMS and carbonyl-iron nanoparticles together to obtain a flexible thin film. With combined, simultaneous regulation of magnetic stimulus and mechanical pumping, the desired chemical release rate can easily be realized. For example, the dose release experimental data was well fitted by a mathematical sigmoidal model, exhibiting a typical dose-response relationship, which shows promise in providing significant guidance for on-demand drug delivery. To test the platform’s feasibility, our microfluidic device was employed in an experiment involving Escherichia coli culture under controlled antibiotic ciprofloxacin exposure, and the expected outcomes were successfully obtained. Our experimental results indicate that such a microfluidic device, with high accuracy and easy manipulation properties, can legitimately be characterized as active chemical release system.

  9. Microfluidic Device for Controllable Chemical Release via Field-Actuated Membrane Incorporating Nanoparticles

    KAUST Repository

    Wang, Xiang

    2013-01-01

    We report a robust magnetic-membrane-based microfluidic platform for controllable chemical release. The magnetic membrane was prepared by mixing polydimethylsiloxane (PDMS) and carbonyl-iron nanoparticles together to obtain a flexible thin film. With combined, simultaneous regulation of magnetic stimulus and mechanical pumping, the desired chemical release rate can easily be realized. For example, the dose release experimental data was well fitted by a mathematical sigmoidal model, exhibiting a typical dose-response relationship, which shows promise in providing significant guidance for on-demand drug delivery. To test the platform’s feasibility, our microfluidic device was employed in an experiment involving Escherichia coli culture under controlled antibiotic ciprofloxacin exposure, and the expected outcomes were successfully obtained. Our experimental results indicate that such a microfluidic device, with high accuracy and easy manipulation properties, can legitimately be characterized as active chemical release system.

  10. A New Pricing Scheme for Controlling Energy Storage Devices in Future Smart Grid

    Directory of Open Access Journals (Sweden)

    Jingwei Zhu

    2014-01-01

    Full Text Available Improvement of the overall efficiency of energy infrastructure is one of the main anticipated benefits of the deployment of smart grid technology. Advancement in energy storage technology and two-way communication in the electric network are indispensable components to achieve such a vision, while efficient pricing schemes and appropriate storage management are also essential. In this paper, we propose a universal pricing scheme which permits one to indirectly control the energy storage devices in the grid to achieve a more desirable aggregate demand profile that meets a particular target of the grid operator such as energy generation cost minimization and carbon emission reduction. Such a pricing scheme can potentially be applied to control the behavior of energy storage devices installed for integration of intermittent renewable energy sources that have permission to grid connection and will have broader applications as an increasing number of novel and low-cost energy storage technologies emerge.

  11. Ocular perfusion pressure control during pars plana vitrectomy: testing a novel device.

    Science.gov (United States)

    Rossi, Tommaso; Querzoli, Giorgio; Gelso, Aldo; Angelini, Giampiero; Rossi, Alessandro; Corazza, Paolo; Landi, Laura; Telani, Serena; Ripandelli, Guido

    2017-09-08

    To study the efficacy of a novel device intended to control infusion pressure based on mean ocular perfusion pressure (MOPP) during pars plana vitrectomy (PPV). An arm blood pressure cuff connected to a vitrectomy machine calculated mean arterial pressure (MAP), while a pressure sensor close to the infusion trocar measured intraocular pressure (IOP). MOPP was calculated in real time in 36 consecutive patients undergoing PPV, who were divided into two groups. The device lowered IOP every time that calculated MOPP fell below 30 mmHg in the Control ON group (18 patients), while no action was taken in the Control OFF group (18 patients). Baseline IOP and blood pressure were similar between groups. The Control ON group had significantly lower average intraoperative IOP (30.5 ± 2.1 vs. 35.9 ± 6.9 mmHg; p = 0.002) and higher MOPP (56.4 ± 5.9 vs. 49.7 ± 6.1 mmHg) than the Control OFF group. The Control ON group also spent less time at MOPP < 10 mmHg and < 30 mmHg: 0 vs. 3.40 ± 2.38 min (p < 0.001) and 9.91 ± 7.15 vs. 16.13 ± 8.12 min (p = 0.02), respectively. The MOPP control device effectively maintained lower IOP and higher MOPP throughout surgery. It also helped avoid dangerous IOP peaks and MOPP dips, allowing patients to spend less time at MOPP of < 10 and < 30 mmHg.

  12. Training approaches for the deployment of a mechanical chest compression device: a randomised controlled manikin study.

    Science.gov (United States)

    Couper, Keith; Velho, Rochelle M; Quinn, Tom; Devrell, Anne; Lall, Ranjit; Orriss, Barry; Yeung, Joyce; Perkins, Gavin D

    2018-02-01

    To evaluate the effect of training strategy on team deployment of a mechanical chest compression device. Randomised controlled manikin trial. Large teaching hospital in the UK. Twenty teams, each comprising three clinicians. Participating individuals were health professionals with intermediate or advanced resuscitation training. Teams were randomised in a 1:1 ratio to receive either standard mechanical chest compression device training or pit-crew device training. Training interventions lasted up to 1 h. Performance was measured immediately after training in a standardised simulated cardiac arrest scenario in which teams were required to deploy a mechanical chest compression device. Primary outcome was chest compression flow fraction in the minute preceding the first mechanical chest compression. Secondary outcomes included cardiopulmonary resuscitation quality and mechanical device deployment metrics, and non-technical skill performance. Outcomes were assessed using video recordings of the test scenario. In relation to the primary outcome of chest compression flow fraction in the minute preceding the first mechanical chest compression, we found that pit-crew training was not superior to standard training (0.76 (95% CI 0.73 to 0.79) vs 0.77 (95% CI 0.73 to 0.82), mean difference -0.01 (95% CI -0.06 to 0.03), P=0.572). There was also no difference between groups in performance in relation to any secondary outcome. Pit-crew training, compared with standard training, did not improve team deployment of a mechanical chest device in a simulated cardiac arrest scenario. ISRCTN43049287; Pre-results. © Article author(s) (or their employer(s) unless otherwise stated in the text of the article) 2018. All rights reserved. No commercial use is permitted unless otherwise expressly granted.

  13. Controllable design of solid-state perovskite solar cells by SCAPS device simulation

    Science.gov (United States)

    Tan, Kai; Lin, Peng; Wang, Gang; Liu, Yan; Xu, Zongchang; Lin, Yixin

    2016-12-01

    The highest power conversion efficiency (PCE) of solid-state perovskite solar cells (ssPSCs) has achieved 20.1% recently. There is reason to believe that ssPSCs is a strong competitor with silicon and CIGS solar cells in photovoltaic field. The deep understanding of operation mechanism of ssPSCs is essential and required to furtherly improve device performance. The configuration and excition type are similar to inorganic semiconductor solar cells. Therefore, Solar Cell Capacitance Simulator (SCAPS), a device simulator widely using in inorganic solar cells, was employed to controllably design ssPSCs. The validity of device simulation was verified by comparing with real devices from reported literatures. The influence of absorber thickness on device property was discussed, which indicate that it exists an optimal thickness range. Two hypothetical interface layers, TiO2/perovskite layer and perovskite/HTM layer, were introduced into the construction model to consider the effects of interfaces defect density on device performance. It revealed TiO2/perovskite has stronger impact than perovskite/HTM, because higher excess carrier density existing at TiO2/perovskite will cause more recombination rate. In addition, hole transport materials (HTM) parameters, hole mobility and acceptor density, were chosen to study the impact of HTM characteristics on PCE. The analysis illuminate that the design of HTM layer should balance hole mobility and acceptor density. Meanwhile, different HTM candidates were selected and replaced typical HTM layer. The discussion about the function of candidates on solar cells performance demonstrated that a thiophene group hole-transporting polymer (PTAA) and a copper-based conductor (CuI) both have relatively high PCE, which is due to their wide bandgap, high conductivity, and better chemical interaction with perovskite absorber.

  14. Generation of Controlled Analog Emissions from Embedded Devices using Software Stress Methods

    Science.gov (United States)

    2017-03-01

    Generation of Controlled Analog Emissions from Embedded Devices using Software Stress Methods Oren Sternberg, Jonathan H. Nelson, Israel Perez...as dynamic memory allocation, hard disk writing and computations. Each stressing operation creates a pulse in an amplitude shift keying scheme...software stress testing and diagnostic and security applications including StressLinux (Linux) [17], KALI (Linux) [18] and a multitude of tools in

  15. The Encephalophone: A Novel Musical Biofeedback Device using Conscious Control of Electroencephalogram (EEG)

    OpenAIRE

    Thomas A. Deuel; Pampin, Juan; Sundstrom, Jacob; Darvas, Felix

    2017-01-01

    A novel musical instrument and biofeedback device was created using electroencephalogram (EEG) posterior dominant rhythm (PDR) or mu rhythm to control a synthesized piano, which we call the Encephalophone. Alpha-frequency (8–12 Hz) signal power from PDR in the visual cortex or from mu rhythm in the motor cortex was used to create a power scale which was then converted into a musical scale, which could be manipulated by the individual in real time. Subjects could then generate different notes ...

  16. Active DC Bus Signaling Control Method for Coordinating Multiple Energy Storage Devices in DC Microgrid

    OpenAIRE

    Li, Fulong; Lin, Zhengyu; Qian, Zhongnan; Wu, Jiande

    2017-01-01

    This paper will be presented in 2017 Second IEEE International Conference on DC Microgrids (ICDCM) on 28th June 2017. Abstract: Management of multiple energy storage devices in a DC microgrid is a challenge. Conventional method, such as droop control, cannot ensure accurate current sharing in coordinating multiple battery banks, which limits the DC microgrid system performance. This paper proposed an active DC bus signaling (ADBS) method to coordinate multiple battery banks in a DC microg...

  17. TASER® Electronic Control Device-Induced Rhabdomyolysis and Renal Failure: A Case Report

    OpenAIRE

    Gleason, James Benjamin; Ahmad, Ibrahim

    2015-01-01

    Many law enforcement agencies around the United States are employing the use of TASER® electronic control devices (TASER® International Inc.) to subdue combative suspects. Since its inception the TASER® has had a temporal association with reports of rhabdomyolysis. Case reports have reported TASER® induced rhabdomyolysis as mild but serious cases have also been reported. Herein we present the case of a single patient who was admitted to our health network with severe rhabdomyolysis after rece...

  18. A New Vibration Measurement Procedure for On-Line Quality Control of Electronic Devices

    Directory of Open Access Journals (Sweden)

    Gian Marco Revel

    2002-01-01

    Full Text Available In this paper the problem of experimentally testing the mechanical reliability of electronic components for quality control is approached. In general, many tests are performed on electronic devices (personal computers, power supply units, lamps, etc., according to the relevant international standards (IEC, in order to verify their resistance to shock and vibrations, but these are mainly “go no-go” experiments, performed on few samples taken from the production batches.

  19. Characterization of controlled cortical impact devices by high-speed image analysis.

    Science.gov (United States)

    Kim, Yeonho; Fu, Amanda H; Tucker, Laura B; Liu, Jiong; McCabe, Joseph T

    2017-07-04

    As a consequence of their commercial availability, ease of use, and reproducibility, controlled cortical impact (CCI) devices have attained significant prevalence in preclinical traumatic brain injury research. With a CCI, the severity of injury is controlled by varying the impact depth, velocity, and duration, but the actual performance of the device is not well appreciated, partly because of the velocity and short travel distance to impact. This study used a high-speed video digital camera to investigate the performance of five electromagnetically driven CCI devices of the same model. Videography indicated that the impactor tip made a series of distinctive vertical advances and retractions before it attained the desired preset depth; this was also observed in male mouse CCI tests. The impactor tip was also observed to move in the horizontal direction by .8-1.6 mm. On the first advance, the tip extended a distance that was shorter than the preset depth and the velocity of impactor tip was slightly faster than the preset values for three of the five machines. One of the devices was evaluated on four separate occasions over a 14-month period and was found to operate consistently over time. Overall, differences in impact depth and velocity between the devices were modest, suggesting that comparisons of experimental results from different laboratories will generally be informative, particularly if reports provide relevant descriptions of neuropathology. However, the repetitive extension and retraction and horizontal movement of the tip suggests caution in modeling CCI as a single injurious event. Published 2017. This article is a U.S. Government work and is in the public domain in the USA.

  20. Quality Control of Conventional Radiology Devices in Selected Hospitals of Khuzestan Province, Iran

    Directory of Open Access Journals (Sweden)

    Behrouz Rasuli

    2015-07-01

    Full Text Available Introduction Quality control techniques used to test the components of the radiological system and verify that the equipment is operating satisfactorily. In this study, quality control (QC assessment of conventional radiology devices was performed in frequently visited radiology centers of Khuzestan province, Iran. Materials and Methods Fifteen conventional radiology devices were examined, based on the protocol proposed in Report No. 77 by the Institute of Physics and Engineering in Medicine (IPEM. Ten standard QC tests, including voltage accuracy and reproducibility, exposure time accuracy and reproducibility, tube output linearity (time and milliampere, filtration (half-value layer, tube output (70 kV at FSD =100 cm, tube output reproducibility and beam alignment were performed and assessed. All measurements were performed, using Barracuda multi-purpose detector. Results The reproducibility of voltage, exposure time and dose output, as well as output linearity, met the standard criteria in all devices. However, in 60% of the units, the results of the beam alignment test were poor. We also found that 66.7% of the studied units offer services to more than 18,000 patients annually or 50 patients per day. Conclusion Despite the fact that radiological devices in Khuzestan province are relatively old with high workload, the obtained results showed that these devices met the standard criteria. This may be mainly related to proper after-sale services, provided by the companies. Although these services may be expensive for radiology centers, the costs may be significantly reduced if QC is defined as a routine procedure performed by qualified medical physicists or radiation safety officers.

  1. Quality Control of Conventional Radiology Devices in Selected Hospitals of Khuzestan Province, Iran

    Directory of Open Access Journals (Sweden)

    Behrouz Rasuli

    2015-07-01

    Full Text Available Introduction Quality control techniques used to test the components of the radiological system and verify that the equipment is operating satisfactorily. In this study, quality control (QC assessment of conventional radiology devices was performed in frequently visited radiology centers of Khuzestan province, Iran. Materials and Methods Fifteen conventional radiology devices were examined, based on the protocol proposed in Report No. 77 by the Institute of Physics and Engineering in Medicine (IPEM. Ten standard QC tests, including voltage accuracy and reproducibility, exposure time accuracy and reproducibility, tube output linearity (time and milliampere, filtration (half-value layer, tube output (70 kV at FSD =100 cm, tube output reproducibility and beam alignment were performed and assessed. All measurements were performed, using Barracuda multi-purpose detector. Results Thereproducibility of voltage, exposure time and dose output, as well as output linearity, met the standard criteria in all devices. However, in 60% of the units, the results of the beam alignment test were poor. We also found that 66.7% of the studied units offer services to more than 18,000 patients annually or 50 patients per day. Conclusion Despite the fact that radiological devices in Khuzestan province are relatively old with high workload, the obtained results showed that these devices met the standard criteria. This may be mainly related to proper after-sale services, provided by the companies. Although these services may be expensive for radiology centers, the costs may be significantly reduced if QC is defined as a routine procedure performed by qualified medical physicists or radiation safety officers.

  2. Optimizing the construction of devices to control inaccesible surfaces - case study

    Science.gov (United States)

    Niţu, E. L.; Costea, A.; Iordache, M. D.; Rizea, A. D.; Babă, Al

    2017-10-01

    The modern concept for the evolution of manufacturing systems requires multi-criteria optimization of technological processes and equipments, prioritizing associated criteria according to their importance. Technological preparation of the manufacturing can be developed, depending on the volume of production, to the limit of favourable economical effects related to the recovery of the costs for the design and execution of the technological equipment. Devices, as subsystems of the technological system, in the general context of modernization and diversification of machines, tools, semi-finished products and drives, are made in a multitude of constructive variants, which in many cases do not allow their identification, study and improvement. This paper presents a case study in which the multi-criteria analysis of some structures, based on a general optimization method, of novelty character, is used in order to determine the optimal construction variant of a control device. The rational construction of the control device confirms that the optimization method and the proposed calculation methods are correct and determine a different system configuration, new features and functions, and a specific method of working to control inaccessible surfaces.

  3. Electrowetting-induced drop generation and control in a microfluidic flow-focusing device

    Science.gov (United States)

    Malloggi, Florent; Vanapalli, Siva A.; Gu, Hao; van den Ende, Dirk; Mugele, Frieder

    2007-11-01

    Recent upsurge in droplet-based microfluidic research is fueled by the potential application of drops as well-controlled environments for biochemical reactions, single cell analysis and fluid logical devices. Commonly pressure driven flows are used to create droplets continuously either in a flow-focusing or in T-junction geometry. While this approach provides high throughput capability, it is neither amenable to detailed on-demand generation of individual drops nor to dynamic control of surface wettability, which can dramatically affect the dynamics of two-phase microflows. Alternatively, electrowetting (EW)-on-dielectric is used to digitally manipulate drops. The EW provides exquisite control over individual drops and surface wettability. However, current implementations have low throughput and cannot readily be integrated with existing channel-based technologies. Here, we adopt a unified approach to create a soft microfluidic platform that harvests the power of both methods and offers the capability to address their limitations. We achieve this integration by incorporating EW into a flow-focusing device and demonstrate EW-controlled drop formation. We identify experimentally the range of voltages and driving pressures that yields EW-induced droplet generation. A theoretical description based on the balance of external pressures and voltage-controlled capillary pressures quantitatively accounts for the observations. Moreover we show that the smaller the geometric scales the more efficient the electrowetting control of drop generation.

  4. Seismic Proofing Capability of the Accumulated Semiactive Hydraulic Damper as an Active Interaction Control Device with Predictive Control

    Directory of Open Access Journals (Sweden)

    Ming-Hsiang Shih

    2016-01-01

    Full Text Available The intensity of natural disasters has increased recently, causing buildings’ damages which need to be reinforced to prevent their destruction. To improve the seismic proofing capability of Accumulated Semiactive Hydraulic Damper, it is converted to an Active Interaction Control device and synchronous control and predictive control methods are proposed. The full-scale shaking table test is used to test and verify the seismic proofing capability of the proposed AIC with these control methods. This study examines the shock absorption of test structure under excitation by external forces, influences of prediction time, stiffness of the auxiliary structure, synchronous switching, and asynchronous switching on the control effects, and the influence of control locations of test structure on the control effects of the proposed AIC. Test results show that, for the proposed AIC with synchronous control and predictive control of 0.10~0.13 seconds, the displacement reduction ratios are greater than 71%, the average acceleration reduction ratios are, respectively, 36.2% and 36.9%, at the 1st and 2nd floors, and the average base shear reduction ratio is 29.6%. The proposed AIC with suitable stiffeners for the auxiliary structure at each floor with synchronous control and predictive control provide high reliability and practicability for seismic proofing of buildings.

  5. Measurement of treatment compliance using a medical device for glaucoma patients associated with intraocular pressure control: a survey.

    Science.gov (United States)

    Nordmann, Jean-Philippe; Baudouin, Christophe; Renard, Jean-Paul; Denis, Philippe; Lafuma, Antoine; Laurendeau, Caroline; Jeanbat, Viviane; Berdeaux, Gilles

    2010-07-30

    To identify and characterize treatment compliance profiles of glaucoma patients and evaluate the association with intraocular pressure (IOP). A computerized device (Travalert((R))) that recorded daily instillation times and eye-drop counts was given for 3 months. Patients were declared compliant when at least 2 drops were instilled per day. Compliance rates were calculated for weekdays and weekends, separately, over 8 consecutive weeks. A principal components analysis (PCA) was followed by an ascendant hierarchical classification (AHC) to identify compliance groups. 140 patients were recruited (mean age 65.5 years; 51.8% female) of whom 83.6% had primary open-angle glaucoma with mean IOP 23.9 mmHg before Travalert((R)) use. 60.7% were treated with DuoTrav((R)) (travoprost timolol fixed combination) and 39.3% with travoprost. The PCA identified two axes (compliance and treatment weeks). The AHC identified 3 compliance groups: 'high' (56.6%, approx. 80% compliance), 'medium' (21.2%, approx. 50% compliance), and 'low' (22.1%, approx. 20% compliance). Demographics and glaucoma parameters did not predict low compliance. Final mean IOP was 16.1 mmHg, but higher in the low compliance group (17.7 mmHg, P = 0.02). Compliance measurement by a medical device showed compliance rates IOP control. No demographic or glaucoma variable was associated with low compliance.

  6. The Encephalophone: A Novel Musical Biofeedback Device using Conscious Control of Electroencephalogram (EEG).

    Science.gov (United States)

    Deuel, Thomas A; Pampin, Juan; Sundstrom, Jacob; Darvas, Felix

    2017-01-01

    A novel musical instrument and biofeedback device was created using electroencephalogram (EEG) posterior dominant rhythm (PDR) or mu rhythm to control a synthesized piano, which we call the Encephalophone. Alpha-frequency (8-12 Hz) signal power from PDR in the visual cortex or from mu rhythm in the motor cortex was used to create a power scale which was then converted into a musical scale, which could be manipulated by the individual in real time. Subjects could then generate different notes of the scale by activation (event-related synchronization) or de-activation (event-related desynchronization) of the PDR or mu rhythms in visual or motor cortex, respectively. Fifteen novice normal subjects were tested in their ability to hit target notes presented within a 5-min trial period. All 15 subjects were able to perform more accurately (average of 27.4 hits, 67.1% accuracy for visual cortex/PDR signaling; average of 20.6 hits, 57.1% accuracy for mu signaling) than a random note generation (19.03% accuracy). Moreover, PDR control was significantly more accurate than mu control. This shows that novice healthy individuals can control music with better accuracy than random, with no prior training on the device, and that PDR control is more accurate than mu control for these novices. Individuals with more years of musical training showed a moderate positive correlation with more PDR accuracy, but not mu accuracy. The Encephalophone may have potential applications both as a novel musical instrument without requiring movement, as well as a potential therapeutic biofeedback device for patients suffering from motor deficits (e.g., amyotrophic lateral sclerosis (ALS), brainstem stroke, traumatic amputation).

  7. The Encephalophone: A Novel Musical Biofeedback Device using Conscious Control of Electroencephalogram (EEG

    Directory of Open Access Journals (Sweden)

    Thomas A. Deuel

    2017-04-01

    Full Text Available A novel musical instrument and biofeedback device was created using electroencephalogram (EEG posterior dominant rhythm (PDR or mu rhythm to control a synthesized piano, which we call the Encephalophone. Alpha-frequency (8–12 Hz signal power from PDR in the visual cortex or from mu rhythm in the motor cortex was used to create a power scale which was then converted into a musical scale, which could be manipulated by the individual in real time. Subjects could then generate different notes of the scale by activation (event-related synchronization or de-activation (event-related desynchronization of the PDR or mu rhythms in visual or motor cortex, respectively. Fifteen novice normal subjects were tested in their ability to hit target notes presented within a 5-min trial period. All 15 subjects were able to perform more accurately (average of 27.4 hits, 67.1% accuracy for visual cortex/PDR signaling; average of 20.6 hits, 57.1% accuracy for mu signaling than a random note generation (19.03% accuracy. Moreover, PDR control was significantly more accurate than mu control. This shows that novice healthy individuals can control music with better accuracy than random, with no prior training on the device, and that PDR control is more accurate than mu control for these novices. Individuals with more years of musical training showed a moderate positive correlation with more PDR accuracy, but not mu accuracy. The Encephalophone may have potential applications both as a novel musical instrument without requiring movement, as well as a potential therapeutic biofeedback device for patients suffering from motor deficits (e.g., amyotrophic lateral sclerosis (ALS, brainstem stroke, traumatic amputation.

  8. Blood factors of Sus scrofa following a series of three TASER electronic control device exposures.

    Science.gov (United States)

    Jauchem, James R; Cook, Michael C; Beason, Charles W

    2008-03-05

    In a previous study, 18 repeated exposures of anaesthetized swine to an electro-muscular incapacitating device (TASER International's ADVANCED TASER X26 electronic control device) resulted in acidosis and increases in blood electrolytes. In the current study, experiments were performed to investigate effects of a more typical scenario of repeated exposures of the device on muscle contraction and changes in blood factors. Ten swine were exposed for 5s, followed by a 5-s period of no exposure, three times. Selected blood factors were monitored for 3h following exposure. Transient increases in blood glucose, lactate, sodium, potassium, calcium, and pCO(2) were consistent with previous reports in the literature dealing with studies of muscle stimulation or exercise. Blood pH was decreased immediately following exposure, but subsequently returned toward a normal level. Oxygen saturation (measured by pulse oximetry) was not changed significantly. In conclusion, three repeated TASER device exposures had only transient effects on blood factors, which all returned to pre-exposure levels, with the exception of hematocrit (which remained elevated after 3h). Since the increase in this factor was less than that which may occur after short periods of exercise, it is unlikely that this would be an indicator of any serious harm.

  9. Impact of Thyristors Controlled Series Capacitor Devices and Optimal Power Flow on Power Systems

    Directory of Open Access Journals (Sweden)

    Fatiha LAKDJA

    2010-12-01

    Full Text Available This paper presents an algorithm, for solving the Optimal Power Flow problem with flexible AC transmission systems (FACTS. The type of FACTS devices is used: thyristor-controlled series capacitor (TCSC. A method to determine the optimal location of thyristor controlled series compensators has been suggested. The proposed approaches have been implemented on an adapted IEEE 26 bus system. The simulation results are discussed to show the performance of the proposed algorithm and our “FACTS programmer “simulator technique, which are compared with TCSC and without TCSC.

  10. Method for reading sensors and controlling actuators using audio interfaces of mobile devices.

    Science.gov (United States)

    Aroca, Rafael V; Burlamaqui, Aquiles F; Gonçalves, Luiz M G

    2012-01-01

    This article presents a novel closed loop control architecture based on audio channels of several types of computing devices, such as mobile phones and tablet computers, but not restricted to them. The communication is based on an audio interface that relies on the exchange of audio tones, allowing sensors to be read and actuators to be controlled. As an application example, the presented technique is used to build a low cost mobile robot, but the system can also be used in a variety of mechatronics applications and sensor networks, where smartphones are the basic building blocks.

  11. Open loop control of filament heating power supply for large volume plasma device

    Energy Technology Data Exchange (ETDEWEB)

    Sugandhi, R., E-mail: ritesh@ipr.res.in [Institute for Plasma Research, Gandhinagar, Gujarat 382428 (India); Homi Bhabha National Institute, Mumbai 400094 (India); Srivastava, P.K.; Sanyasi, A.K. [Homi Bhabha National Institute, Mumbai 400094 (India); Srivastav, Prabhakar [Institute for Plasma Research, Gandhinagar, Gujarat 382428 (India); Homi Bhabha National Institute, Mumbai 400094 (India); Awasthi, L.M., E-mail: kushagra.lalit@gmail.com [Institute for Plasma Research, Gandhinagar, Gujarat 382428 (India); Homi Bhabha National Institute, Mumbai 400094 (India); Mattoo, S.K. [Homi Bhabha National Institute, Mumbai 400094 (India)

    2017-02-15

    A power supply (20 V, 10 kA) for powering the filamentary cathode has been procured, interfaced and integrated with the centralized control system of Large Volume Plasma Device (LVPD). Software interface has been developed on the standard Modbus RTU communication protocol. It facilitates the dashboard for configuration, on line status monitoring, alarm management, data acquisition, synchronization and controls. It has been tested for stable operation of the power supply for the operational capabilities. The paper highlights the motivation, interface description, implementation and results obtained.

  12. Electrical power distribution control methods, electrical energy demand monitoring methods, and power management devices

    Science.gov (United States)

    Chassin, David P.; Donnelly, Matthew K.; Dagle, Jeffery E.

    2006-12-12

    Electrical power distribution control methods, electrical energy demand monitoring methods, and power management devices are described. In one aspect, an electrical power distribution control method includes providing electrical energy from an electrical power distribution system, applying the electrical energy to a load, providing a plurality of different values for a threshold at a plurality of moments in time and corresponding to an electrical characteristic of the electrical energy, and adjusting an amount of the electrical energy applied to the load responsive to an electrical characteristic of the electrical energy triggering one of the values of the threshold at the respective moment in time.

  13. The inherent weaknesses in industrial control systems devices; hacking and defending SCADA systems

    Science.gov (United States)

    Bianco, Louis J.

    The North American Electric Reliability Corporation (NERC) is about to enforce their NERC Critical Infrastructure Protection (CIP) Version Five and Six requirements on July 1st 2016. The NERC CIP requirements are a set of cyber security standards designed to protect cyber assets essential the reliable operation of the electric grid. The new Version Five and Six requirements are a major revision to the Version Three (currently enforced) requirements. The new requirements also bring substations into scope alongside Energy Control Centers. When the Version Five requirements were originally drafted they were vague, causing in depth discussions throughout the industry. The ramifications of these requirements has made owners look at their systems in depth, questioning how much money it will take to meet these requirements. Some owners saw backing down from routable networks to non-routable as a means to save money as they would be held to less requirements within the standards. Some owners saw removing routable connections as a proper security move. The purpose of this research was to uncover the inherent weaknesses in Industrial Control Systems (ICS) devices; to show how ICS devices can be hacked and figure out potential protections for these Critical Infrastructure devices. In addition, this research also aimed to validate the decision to move from External Routable connectivity to Non-Routable connectivity, as a security measure and not as a means of savings. The results reveal in order to ultimately protect Industrial Control Systems they must be removed from the Internet and all bi-directional external routable connections must be removed. Furthermore; non-routable serial connections should be utilized, and these non-routable serial connections should be encrypted on different layers of the OSI model. The research concluded that most weaknesses in SCADA systems are due to the inherent weaknesses in ICS devices and because of these weaknesses, human intervention is

  14. Flow Control Device Evaluation for an Internal Flow with an Adverse Pressure Gradient

    Science.gov (United States)

    Jenkins, Luther N.; Gorton, Susan Althoff; Anders, Scott G.

    2002-01-01

    The effectiveness of several active and passive devices to control flow in an adverse pressure gradient with secondary flows present was evaluated in the 15 Inch Low Speed Tunnel at NASA Langley Research Center. In this study, passive micro vortex generators, micro bumps, and piezoelectric synthetic jets were evaluated for their flow control characteristics using surface static pressures, flow visualization, and 3D Stereo Digital Particle Image Velocimetry. Data also were acquired for synthetic jet actuators in a zero flow environment. It was found that the micro vortex generator is very effective in controlling the flow environment for an adverse pressure gradient, even in the presence of secondary vortical flow. The mechanism by which the control is effected is a re-energization of the boundary layer through flow mixing. The piezoelectric synthetic jet actuators must have sufficient velocity output to produce strong longitudinal vortices if they are to be effective for flow control. The output of these devices in a laboratory or zero flow environment will be different than the output in a flow environment. In this investigation, the output was higher in the flow environment, but the stroke cycle in the flow did not indicate a positive inflow into the synthetic jet.

  15. Effectiveness of an inlet flow turbulence control device to simulate flight fan noise in an anechoic chamber

    Science.gov (United States)

    Woodward, R. P.; Wazyniak, J. A.; Shaw, L. M.; Mackinnon, M. J.

    1977-01-01

    A hemispherical inlet flow control device was tested on a 50.8 cm. (20-inch) diameter fan stage in the NASA-Lewis Anechoic Chamber. The control device used honeycomb and wire mesh to reduce turbulence intensities entering the fan. Far field acoustic power level results showed about a 5 dB reduction in blade passing tone and about 10 dB reduction in multiple pure tone sound power at 90% design fan speed with the inlet device in place. Hot film cross probes were inserted in the inlet to obtain data for two components of the turbulence at 65 and 90% design fan speed. Without the flow control device the axial intensities were below 1.0%, while the circumferential intensities were almost twice this value. The inflow control device significantly reduced the circumferential turbulence intensities and also reduced the axial length scale.

  16. Effectiveness of an inlet flow turbulence control device to simulate flight noise fan in an anechoic chamber

    Science.gov (United States)

    Woodward, R. P.; Wazyniak, J. A.; Shaw, L. M.; Mackinnon, M. J.

    1977-01-01

    A hemispherical inlet flow control device was tested on a 50.8 cm. (20-inch) diameter fan stage in the NASA-Lewis anechoic chamber. The control device used honeycomb and wire mesh to reduce turbulence intensities entering the fan. Far field acoustic power level results show about a 5 db reduction in blade passing tone and about 10 dB reduction in multiple pure tone sound power at 90% design fan speed with the inlet device in place. Hot film cross probes were inserted in the inlet to obtain data for two components of the turbulence at 65 and 90% design fan speed. Without the flow control device, the axial intensities were below 1.0%, while the circumferential intensities were almost twice this value. The inflow control device significantly reduced the circumferential turbulence intensities and also reduced the axial length scale.

  17. Wireless, Web-Based Interactive Control of Optical Coherence Tomography with Mobile Devices.

    Science.gov (United States)

    Mehta, Rajvi; Nankivil, Derek; Zielinski, David J; Waterman, Gar; Keller, Brenton; Limkakeng, Alexander T; Kopper, Regis; Izatt, Joseph A; Kuo, Anthony N

    2017-01-01

    Optical coherence tomography (OCT) is widely used in ophthalmology clinics and has potential for more general medical settings and remote diagnostics. In anticipation of remote applications, we developed wireless interactive control of an OCT system using mobile devices. A web-based user interface (WebUI) was developed to interact with a handheld OCT system. The WebUI consisted of key OCT displays and controls ported to a webpage using HTML and JavaScript. Client-server relationships were created between the WebUI and the OCT system computer. The WebUI was accessed on a cellular phone mounted to the handheld OCT probe to wirelessly control the OCT system. Twenty subjects were imaged using the WebUI to assess the system. System latency was measured using different connection types (wireless 802.11n only, wireless to remote virtual private network [VPN], and cellular). Using a cellular phone, the WebUI was successfully used to capture posterior eye OCT images in all subjects. Simultaneous interactivity by a remote user on a laptop was also demonstrated. On average, use of the WebUI added only 58, 95, and 170 ms to the system latency using wireless only, wireless to VPN, and cellular connections, respectively. Qualitatively, operator usage was not affected. Using a WebUI, we demonstrated wireless and remote control of an OCT system with mobile devices. The web and open source software tools used in this project make it possible for any mobile device to potentially control an OCT system through a WebUI. This platform can be a basis for remote, teleophthalmology applications using OCT.

  18. A control system for ultrasound devices utilized for inactivating E. coli in wastewater.

    Science.gov (United States)

    Ohrdes, H; Ille, I; Twiefel, J; Wallaschek, J; Nogueira, R; Rosenwinkel, K-H

    2018-01-01

    Sonochemical processes applied to wastewater treatment have an influence on the behavior of ultrasonic systems. This is especially due to the load characteristic of the sonochemical process itself and the temperature increase caused by internal damping within the converter. Hence, a controlling device is needed to guarantee the operation in resonance and to keep the vibration amplitude constant. This paper presents a digital control system for the operation of weak to strong damped ultrasonic devices and its application for inactivating Escherichia coli in wastewater. In an experimental investigation, the electric data during a sonochemical process to inactivate E. coli in wastewater is taken into account to analyze the efficacy of the treatment process and the reaction of the vibration system to the process. Frequency response measurements depict that the resonance frequency changes with the sonicated medium and the vibration amplitude decreases with driving current. In addition to a common continuous operation of the system, different pulsed modes are investigated. The experiments prove the common dependencies between inactivation and power level or treatment time. Additionally, it is pointed out that the control of the sonochemical device is of utmost importance to guarantee an efficient treatment of water, because fast process changes, especially in pulsed operation modes, need to be controlled to a steady state as fast as possible. Although a water treatment efficiency increase using pulsed modes was not proved, it is shown, that the performance of the control unit is capable of using different driving modes in water treatment. Copyright © 2017 Elsevier B.V. All rights reserved.

  19. Active flow control for maximizing performance of spark ignited stratified charge engines. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Fedewa, Andrew; Stuecken, Tom; Timm, Edward; Schock, Harold J.; Shih, Tom-I.P.; Koochesfahani, Manooch; Brereton, Giles

    2002-10-15

    Reducing the cycle-to-cycle variability present in stratified-charge engines is an important step in the process of increasing their efficiency. As a result of this cycle-to-cycle variability, fuel injection systems are calibrated to inject more fuel than necessary, in an attempt to ensure that the engines fire on every cycle. When the cycle-to-cycle variability is lowered, the variation of work per cycle is reduced and the lean operating limit decreases, resulting in increased fuel economy. In this study an active flow control device is used to excite the intake flow of an engine at various frequencies. The goal of this excitation is to control the way in which vortices shed off of the intake valve, thus lowering the cycle-to-cycle variability in the flow field. This method of controlling flow is investigated through the use of three engines. The results of this study show that the active flow control device did help to lower the cycle-to-cycle variability of the in-cylinder flow field; however, the reduction did not translate directly into improved engine performance.

  20. Development of a confocal ultrasound device using an inertial cavitation control for transfection in-vitro

    Science.gov (United States)

    Mestas, J. L.; Chettab, K.; Roux, S.; Prieur, F.; Lafond, M.; Dumontet, C.; Lafon, C.

    2015-12-01

    Sonoporation using low-frequency high-pressure ultrasound (US) is a non-viral approach for in vitro and in vivo gene delivery. We developed a new sonoporation device designed for spatial and temporal control of ultrasound cavitation. This device was evaluated for the in vitro transfection efficiency of a plasmid coding for Green Fluorescent Protein (peGFP- C1) in adherent and non-adherent cell lines. The frequency spectrum of the signal receive by a hydrophone is used to compute a cavitation index (CI) representative of the inertial cavitation activity. The influence of the CI on transfection efficiency, as well as reproducibility were determined. A real-time feedback loop control on CI was integrated in the process to regulate the cavitation level during sonoporation. In both adherent and non-adherent cell lines, the sonoporation device produced a highly efficient transfection of peGFP-C1 (40-80%), as determined by flow cytometry analysis of GFP expression, along with a low rate of mortality assessed by propidium iodide staining. Moreover, the sonoporation of non-adherent cell lines Jurkat and K562 was found to be equivalent to nucleofection in terms of efficiency and toxicity while these two cell lines were resistant to transfection with lipofection.

  1. Distributed processing and network of data acquisition and diagnostics control for Large Helical Device (LHD)

    Energy Technology Data Exchange (ETDEWEB)

    Nakanishi, H.; Kojima, M.; Hidekuma, S. [National Inst. for Fusion Science, Toki, Gifu (Japan)

    1997-11-01

    The LHD (Large Helical Device) data processing system has been designed in order to deal with the huge amount of diagnostics data of 600-900 MB per 10-second short-pulse experiment. It prepares the first plasma experiment in March 1998. The recent increase of the data volume obliged to adopt the fully distributed system structure which uses multiple data transfer paths in parallel and separates all of the computer functions into clients and servers. The fundamental element installed for every diagnostic device consists of two kinds of server computers; the data acquisition PC/Windows NT and the real-time diagnostics control VME/VxWorks. To cope with diversified kinds of both device control channels and diagnostics data, the object-oriented method are utilized wholly for the development of this system. It not only reduces the development burden, but also widen the software portability and flexibility. 100Mbps EDDI-based fast networks will re-integrate the distributed server computers so that they can behave as one virtual macro-machine for users. Network methods applied for the LHD data processing system are completely based on the TCP/IP internet technology, and it provides the same accessibility to the remote collaborators as local participants can operate. (author)

  2. A rotational traveling wave based levitation device - Modeling, design, and control

    CERN Document Server

    Gabai, Ran; Shaham, Ran; Cohen, Nadav; Bucher, Izhak

    2016-01-01

    Described is a device acting on an acoustically levitated object by manipulating the pressure and flow of a thin layer of air such that its rotation can be precisely controlled without mechanical contact. Virtual work analysis assists in simplifying the multi-actuator control problem into a problem governed by a controllable parameter. Actuation is done with a vibrating ring capable of producing ultrasonic standing and traveling waves, creating the acoustic excitation that affects the pressure in a thin, intermediate layer of gas. A distinctive vibration pattern is required to generate the temporal and spatial pressure field of the squeezed air layer that gives rise to both acoustic levitation force and rotational torque. Described are the physical and design development stages leading to an optimized structure, all followed by verifying and dynamics-calibration experiments. Moreover, by precisely controlling the ratio of standing and traveling waves in a closed-loop, one can affect the shear forces applied b...

  3. Experimental investigation of aerodynamic devices for wind turbine rotational speed control. Phase 1

    Energy Technology Data Exchange (ETDEWEB)

    Miller, L.S. [Wichita State Univ., KS (United States)

    1995-02-01

    An investigation was undertaken to identify the aerodynamic performance of five separate trailing-edge control devices, and to evaluate their potential for wind turbine overspeed and power modulation applications. A modular two-dimensional wind tunnel model was constructed and evaluated during extensive wind tunnel testing. Aerodynamic lift, drag, suction, and pressure coefficient data were acquired and analyzed for various control configurations and angles of attack. To further interpret their potential performance, the controls were evaluated numerically using a generic wind turbine geometry and a performance analysis computer program. Results indicated that the Spoiler-Flap control configuration was best softed for turbine braking applications. It exhibited a large negative suction coefficient over a broad angle-of-attack range, and good turbine braking capabilities, especially at low tip-speed ratio.

  4. Sensor guided control and navigation with intelligent machines. Final technical report

    Energy Technology Data Exchange (ETDEWEB)

    Ghosh, Bijoy K.

    2001-03-26

    This item constitutes the final report on ''Visionics: An integrated approach to analysis and design of intelligent machines.'' The report discusses dynamical systems approach to problems in robust control of possibly time-varying linear systems, problems in vision and visually guided control, and, finally, applications of these control techniques to intelligent navigation with a mobile platform. Robust design of a controller for a time-varying system essentially deals with the problem of synthesizing a controller that can adapt to sudden changes in the parameters of the plant and can maintain stability. The approach presented is to design a compensator that simultaneously stabilizes each and every possible mode of the plant as the parameters undergo sudden and unexpected changes. Such changes can in fact be detected by a visual sensor and, hence, visually guided control problems are studied as a natural consequence. The problem here is to detect parameters of the plant and maintain st ability in the closed loop using a ccd camera as a sensor. The main result discussed in the report is the role of perspective systems theory that was developed in order to analyze such a detection and control problem. The robust control algorithms and the visually guided control algorithms are applied in the context of a PUMA 560 robot arm control where the goal is to visually locate a moving part on a mobile turntable. Such problems are of paramount importance in manufacturing with a certain lack of structure. Sensor guided control problems are extended to problems in robot navigation using a NOMADIC mobile platform with a ccd and a laser range finder as sensors. The localization and map building problems are studied with the objective of navigation in an unstructured terrain.

  5. Well controlled multiple resistive switching states in the Al local doped HfO2 resistive random access memory device

    Science.gov (United States)

    Chen, Y. S.; Chen, B.; Gao, B.; Liu, L. F.; Liu, X. Y.; Kang, J. F.

    2013-04-01

    The resistive switching behaviors in the sandwiched Ti/HfO2/Pt devices with different doping condition were systematically investigated. We show that, comparing with the undoped and the Al layer doped HfO2 devices, significant improvement of switching characteristics is achieved in the Al local doped HfO2 device, including uniformity, reliability, and operation current. As a result, well controlled multiple switching states are obtained in the local doping device by modulating the set current compliance or the maximal reset voltage, respectively. Our results suggest that the switching characteristics of HfO2 device are very closely related to the inducement and controlling of conductive filaments' growth in the dielectric layer, which can be considered in the optimization of resistive random access memory device design.

  6. Standardizing visual control devices for tsetse flies: East African species Glossina swynnertoni.

    Directory of Open Access Journals (Sweden)

    Furaha Mramba

    Full Text Available BACKGROUND: Here we set out to standardize long-lasting, visually-attractive devices for Glossina swynnertoni, a vector of both human and animal trypanosomiasis in open savannah in Tanzania and Kenya, and in neighbouring conservation areas used by pastoralists. The goal was to determine the most practical device/material that would induce the strongest landing response in G. swynnertoni for use in area-wide population suppression of this fly with insecticide-impregnated devices. METHODS AND FINDINGS: Trials were conducted in wet and dry seasons in the Serengeti and Maasai Mara to measure the performance of traps and targets of different sizes and colours, with and without chemical baits, at different population densities and under different environmental conditions. Adhesive film was used as a simple enumerator at these remote locations to compare trapping efficiencies of devices. Independent of season or presence of chemical baits, targets in phthalogen blue or turquoise blue cloth with adhesive film were the best devices for capturing G. swynnertoni in all situations, catching up to 19 times more flies than pyramidal traps. Baiting with chemicals did not affect the relative performance of devices. Fly landings were two times higher on 1 m(2 blue-black targets as on pyramidal traps when equivalent areas of both were covered with adhesive film. Landings on 1 m(2 blue-black targets were compared to those on smaller phthalogen blue 0.5 m(2 all-blue or blue-black-blue cloth targets, and to landings on all-blue plastic 0.32-0.47 m(2 leg panels painted in phthalogen blue. These smaller targets and leg panels captured equivalent numbers of G. swynnertoni per unit area as bigger targets. CONCLUSIONS: Leg panels and 0.5 m(2 cloth targets show promise as cost effective devices for management of G. swynnertoni as they can be used for both control (insecticide-impregnated cloth and for sampling (rigid plastic with insect glue or adhesive film of

  7. Final report on development of adaptive control algorithm for active control of total power input

    DEFF Research Database (Denmark)

    Laugesen, Søren; Henriksen, Eigil; Ohlrich, Mogens

    1996-01-01

    An adaptive realtime algorithm for minimisation of total power input to a receiving structure has been derived, implemented and tested, and this control algorithm has proved to be robust and reliable. Simulation studies ahve clearly demonstrated that the algorithm behaves exactly as should...... be expected from frequency domain predictions. Experimental trials in the laboratory have supported these observations. Again, the reductions of the measured total power input to the receiving structure were in perfect agreement with the results obtained by analytically minimising the controller cost function....... Apart from the good results obtained with this control strategy under ideal circumstances, observations have also been made of the detrimental effects of 'flanking paths' and measurement errors that may be experienced in a practical implementation....

  8. Features of control systems analysis with discrete control devices using mathematical packages

    Science.gov (United States)

    Yakovleva, E. M.; Faerman, V. A.

    2017-02-01

    The article contains presentation of basic provisions of the theory of automatic pulse control systems as well as methods of analysis of such systems using the mathematical software widespread in the academic environment. The pulse systems under research are considered as analogues systems interacting among themselves, including sensors, amplifiers, controlled objects, and discrete parts. To describe such systems, one uses a mathematical apparatus of difference equations as well as discrete transfer functions. To obtain a transfer function of the open-loop system, being important from the point of view of the analysis of control systems, one uses mathematical packages Mathcad and Matlab. Despite identity of the obtained result, the way of its achievement from the point of view of user’s action is various for the specified means. In particular, Matlab uses a structural model of the control system while Mathcad allows only execution of a chain of operator transforms. It is worth noting that distinctions taking place allow considering transformation of signals during interaction of the linear and continuous parts of the control system from different sides. The latter can be used in an educational process for the best assimilation of the course of the control system theory by students.

  9. Operation and control of large wind turbines and wind farms. Final report

    DEFF Research Database (Denmark)

    Sørensen, Poul Ejnar; Hansen, Anca Daniela; Thomsen, Kenneth

    2005-01-01

    of produced electricity into account. Dynamic models and control strategies for the wind farms have also been developed, with the aim to optimise theoperation of the wind farms considering participation in power system control of power (frequency) and reactive power (voltage), maximise power production, keep...... good power quality and limit mechanical loads and life time consumption. The projectdeveloped models for 3 different concepts for wind farms. Two of the concepts use active stall controlled wind turbines, one with AC connection and one with modern HVDC/VSC connection of the wind farm. The third concept......This report is the final report of a Danish research project “Operation and control of large wind turbines and wind farms”. The objective of the project has been to analyse and assess operational strategies and possibilities for control of different typesof wind turbines and different wind farm...

  10. Modeling of integrated environmental control systems for coal-fired power plants. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Rubin, E.S.; Salmento, J.S.; Frey, H.C.; Abu-Baker, A.; Berkenpas, M.

    1991-05-01

    The Integrated Environmental Control Model (IECM) was designed to permit the systematic evaluation of environmental control options for pulverized coal-fired (PC) power plants. Of special interest was the ability to compare the performance and cost of advanced pollution control systems to ``conventional`` technologies for the control of particulate, SO{sub 2} and NO{sub x}. Of importance also was the ability to consider pre-combustion, combustion and post-combustion control methods employed alone or in combination to meet tough air pollution emission standards. Finally, the ability to conduct probabilistic analyses is a unique capability of the IECM. Key results are characterized as distribution functions rather than as single deterministic values. (VC)

  11. Measuring device for purging water flow rate in control rod drive

    Energy Technology Data Exchange (ETDEWEB)

    Inoue, Hiroshi.

    1993-11-12

    The device of the present invention enables highly accurate measurement for an amount of purging water supplied to control rod drives of a BWR type reactor. That is, purging water is supplied from an inlet of a scram line of the control rod drives. A temperature measuring portion is disposed, for measuring temperature fluctuation of purging water, to a hydropressure control unit for providing pressure and flow rate of water required for supplying the purging water and scram operation. An instrumentation section is disposed for calculating the flow rate of purging water based on the measured data obtained in the section. An output device is disposed for outputting a flow rate value of the purging water based on the result of the calculation obtained therein. With such a constitution, flow rate of the purging water can be measured quantitatively at the hydropressure control unit. Accordingly, influences, such as fluctuation of reactor core temperature are reduced, and accuracy for the measurement of the purging water flow rate is improved. As a result, reactor safety and maintainability can be improved. (I.S.).

  12. Fuzzy logic controllers for electrotechnical devices - On-site tuning approach

    Science.gov (United States)

    Hissel, D.; Maussion, P.; Faucher, J.

    2001-12-01

    Fuzzy logic offers nowadays an interesting alternative to the designers of non linear control laws for electrical or electromechanical systems. However, due to the huge number of tuning parameters, this kind of control is only used in a few industrial applications. This paper proposes a new, very simple, on-site tuning strategy for a PID-like fuzzy logic controller. Thanks to the experimental designs methodology, we will propose sets of optimized pre-established settings for this kind of fuzzy controllers. The proposed parameters are only depending on one on-site open-loop identification test. In this way, this on-site tuning methodology has to be compared to the Ziegler-Nichols one's for conventional controllers. Experimental results (on a permanent magnets synchronous motor and on a DC/DC converter) will underline all the efficiency of this tuning methodology. Finally, the field of validity of the proposed pre-established settings will be given.

  13. Adaptive Kinematic Control of a Robotic Venipuncture Device Based on Stereo Vision, Ultrasound, and Force Guidance.

    Science.gov (United States)

    Balter, Max L; Chen, Alvin I; Maguire, Timothy J; Yarmush, Martin L

    2017-02-01

    Robotic systems have slowly entered the realm of modern medicine; however, outside the operating room, medical robotics has yet to be translated to more routine interventions such as blood sampling or intravenous fluid delivery. In this paper, we present a medical robot that safely and rapidly cannulates peripheral blood vessels-a procedure commonly known as venipuncture. The device uses near-infrared and ultrasound imaging to scan and select suitable injection sites, and a 9-DOF robot to insert the needle into the center of the vessel based on image and force guidance. We first present the system design and visual servoing scheme of the latest generation robot, and then evaluate the performance of the device through workspace simulations and free-space positioning tests. Finally, we perform a series of motion tracking experiments using stereo vision, ultrasound, and force sensing to guide the position and orientation of the needle tip. Positioning experiments indicate sub-millimeter accuracy and repeatability over the operating workspace of the system, while tracking studies demonstrate real-time needle servoing in response to moving targets. Lastly, robotic phantom cannulations demonstrate the use of multiple system states to confirm that the needle has reached the center of the vessel.

  14. Hierarchical and hybrid energy storage devices in data centers: Architecture, control and provisioning

    Science.gov (United States)

    Xue, Yuankun; Bogdan, Paul; Tang, Jian; Wang, Yanzhi; Lin, Xue

    2018-01-01

    Recently, a new approach has been introduced that leverages and over-provisions energy storage devices (ESDs) in data centers for performing power capping and facilitating capex/opex reductions, without performance overhead. To fully realize the potential benefits of the hierarchical ESD structure, we propose a comprehensive design, control, and provisioning framework including (i) designing power delivery architecture supporting hierarchical ESD structure and hybrid ESDs for some levels, as well as (ii) control and provisioning of the hierarchical ESD structure including run-time ESD charging/discharging control and design-time determination of ESD types, homogeneous/hybrid options, ESD provisioning at each level. Experiments have been conducted using real Google data center workloads based on realistic data center specifications. PMID:29351553

  15. Hierarchical and hybrid energy storage devices in data centers: Architecture, control and provisioning.

    Science.gov (United States)

    Sun, Mengshu; Xue, Yuankun; Bogdan, Paul; Tang, Jian; Wang, Yanzhi; Lin, Xue

    2018-01-01

    Recently, a new approach has been introduced that leverages and over-provisions energy storage devices (ESDs) in data centers for performing power capping and facilitating capex/opex reductions, without performance overhead. To fully realize the potential benefits of the hierarchical ESD structure, we propose a comprehensive design, control, and provisioning framework including (i) designing power delivery architecture supporting hierarchical ESD structure and hybrid ESDs for some levels, as well as (ii) control and provisioning of the hierarchical ESD structure including run-time ESD charging/discharging control and design-time determination of ESD types, homogeneous/hybrid options, ESD provisioning at each level. Experiments have been conducted using real Google data center workloads based on realistic data center specifications.

  16. Unified control of DC-DC buck converter using dynamic adaptive controller for battery operated devices

    Directory of Open Access Journals (Sweden)

    Kanimozhi Kannabiran

    2016-01-01

    Full Text Available El objetivo de esta investigación es mejorar la respuesta dinámica del sistema de convertidor DC-DC con incertidumbres en los parámetros internos. La metodología de control por modo deslizante en las obras existentes se basa en un sistema de control proporcional-integral-derivativo (PID. El presente trabajo aborda diversas cuestiones en un enfoque unificado para el diseño y la aplicación de la modulación de ancho de pulso (PWM basado en control digital por modos deslizantes adaptativos (CMD, técnica de control para el controlador buck para los teléfonos móviles que funcionan en modo continuo de conducción (MCC y el modo de conducción discontinua (MCD. El controlador está programado para controlar la ganancia de la condición de carga de salida y cambiar adaptativamente los parámetros de control para dar un rendimiento dinámico óptimo correspondiente a las variaciones de carga. Además, la estabilidad se verifica analíticamente utilizando el criterio de estabilidad de Lyapunov y se prueba que el sistema es global y asintóticamente estable. Finalmente, la eficacia del método propuesto se verifica mediante la simulación y experimentación. Se obtiene una respuesta estable en estado estacionario con ondulación reducida.

  17. Microelectromechanical System (MEMS) Device Being Developed for Active Cooling and Temperature Control

    Science.gov (United States)

    Beach, Duane E.

    2003-01-01

    High-capacity cooling options remain limited for many small-scale applications such as microelectronic components, miniature sensors, and microsystems. A microelectromechanical system (MEMS) using a Stirling thermodynamic cycle to provide cooling or heating directly to a thermally loaded surface is being developed at the NASA Glenn Research Center to meet this need. The device can be used strictly in the cooling mode or can be switched between cooling and heating modes in milliseconds for precise temperature control. Fabrication and assembly employ techniques routinely used in the semiconductor processing industry. Benefits of the MEMS cooler include scalability to fractions of a millimeter, modularity for increased capacity and staging to low temperatures, simple interfaces, limited failure modes, and minimal induced vibration. The MEMS cooler has potential applications across a broad range of industries such as the biomedical, computer, automotive, and aerospace industries. The basic capabilities it provides can be categorized into four key areas: 1) Extended environmental temperature range in harsh environments; 2) Lower operating temperatures for electronics and other components; 3) Precision spatial and temporal thermal control for temperature-sensitive devices; and 4) The enabling of microsystem devices that require active cooling and/or temperature control. The rapidly expanding capabilities of semiconductor processing in general, and microsystems packaging in particular, present a new opportunity to extend Stirling-cycle cooling to the MEMS domain. The comparatively high capacity and efficiency possible with a MEMS Stirling cooler provides a level of active cooling that is impossible at the microscale with current state-of-the-art techniques. The MEMS cooler technology builds on decades of research at Glenn on Stirling-cycle machines, and capitalizes on Glenn s emerging microsystems capabilities.

  18. Development of a standard test procedure for devices on thermal weed control

    Directory of Open Access Journals (Sweden)

    Verschwele, Arnd

    2016-02-01

    Full Text Available In contrast to the standard evaluation of the efficacy of pesticides and the testing of spraying equipment there are no comparable testing procedure for equipment of thermal weed control. It is the aim of the investigations described here to develop a standard procedure for assessing temperature distribution and biological efficacy. This will be the basis for quality testing which can be directly used by practical users. Also it can help engineers to improve devices if constructive gaps will be identified by these tests. The results from testing a flaming device (Green-Flame 850 E demonstrated such a potential for technical improvement: The temperature decreased from 159 °C to 89 °C by increasing driving speed from 0.35 m/s to 0.81 m/s. The variation of the temperature related to the working width was extremely high: The range was 60 °C at highest speed and 79 °C at lowest speed, respectively. The biological efficacy against the test plant species Sinapis arvensis was also affected by the driving speed and the corresponding temperature. A driving speed not higher than 0.53 m/s resulted in efficacy rates of almost 95%. However, the efficacy was only 66% at the highest tested speed of 0.81 m/s. Thus, the needed effective temperature is between 89 °C und 106 °C. In contrast, Lolium perenne was controlled by only 72% under the tested conditions. Here a dose-response relationship was not observed. The variation of the temperature, as well as the biological efficacy, was extremely heterogeneous and not satisfying in terms of an economic and safe use. Similar results were found for other devices on thermal weed control.

  19. An SSVEP based BCI to control a humanoid robot by using portable EEG device.

    Science.gov (United States)

    Güneysu, Arzu; Akin, H Levent

    2013-01-01

    Brain Computer Interfaces (BCIs) are systems that allow human subjects to interact with the environment by interpreting brain signals into machine commands. This work provides a design for a BCI to control a humanoid robot by using signals obtained from the Emotiv EPOC, a portable electroencephalogram (EEG) device with 14 electrodes and sampling rate of 128 Hz. The main objective is to process the neuroelectric responses to an externally driven stimulus and generate control signals for the humanoid robot Nao accordingly. We analyze steady-state visually evoked potential (SSVEP) induced by one of four groups of light emitting diodes (LED) by using two distinct signals obtained from the two channels of the EEG device which reside on top of the occipital lobe. An embedded system is designed for generating pulse width modulated square wave signals in order to flicker each group of LEDs with different frequencies. The subject chooses the direction by looking at one of these groups of LEDs that represent four directions. Fast Fourier Transform and a Gaussian model are used to detect the dominant frequency component by utilizing harmonics and neighbor frequencies. Then, a control signal is sent to the robot in order to draw a fixed sized line in that selected direction by BCI. Experimental results display satisfactory performance where the correct target is detected 75% of the time on the average across all test subjects without any training.

  20. Electrical control simulation of near infrared emission in SOI-MOSFET quantum well devices

    Science.gov (United States)

    Bendayan, Michael; Sabo, Roi; Zolberg, Roee; Mandelbaum, Yaakov; Chelly, Avraham; Karsenty, Avi

    2017-07-01

    In the race to realize ultrahigh-speed processors, silicon photonics research is part of the efforts. Overcoming the silicon indirect bandgap with special geometry, we developed a concept of a metal-oxide-semiconductor field-effect transistor, based on a silicon quantum well structure that enables control of light emission. This quantum well consists of a recessed ultrathin silicon layer, obtained by a gate-recessed channel and limited between two oxide layers. The device's coupled optical and electrical properties have been simulated for channel thicknesses, varying from 2 to 9 nm. The results show that this device can emit near infrared radiation in the 1 to 2 μm range, compatible with the optical networking spectrum. The emitted light intensity can be electrically controlled by the drain voltage Vds while the peak emission wavelength depends on the channel thickness and slightly on Vds. Moreover, the location of the radiative recombination source inside the channel, responsible for the light emission, is also controllable through the applied voltages.

  1. Atomic switch: atom/ion movement controlled devices for beyond von-neumann computers.

    Science.gov (United States)

    Hasegawa, Tsuyoshi; Terabe, Kazuya; Tsuruoka, Tohru; Aono, Masakazu

    2012-01-10

    An atomic switch is a nanoionic device that controls the diffusion of metal ions/atoms and their reduction/oxidation processes in the switching operation to form/annihilate a conductive path. Since metal atoms can provide a highly conductive channel even if their cluster size is in the nanometer scale, atomic switches may enable downscaling to smaller than the 11 nm technology node, which is a great challenge for semiconductor devices. Atomic switches also possess novel characteristics, such as high on/off ratios, very low power consumption and non-volatility. The unique operating mechanisms of these devices have enabled the development of various types of atomic switch, such as gap-type and gapless-type two-terminal atomic switches and three-terminal atomic switches. Novel functions, such as selective volatile/nonvolatile, synaptic, memristive, and photo-assisted operations have been demonstrated. Such atomic switch characteristics can not only improve the performance of present-day electronic systems, but also enable development of new types of electronic systems, such as beyond von- Neumann computers. Copyright © 2012 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  2. Comparative analysis of selected exhaled breath biomarkers obtained with two different temperature-controlled devices

    Directory of Open Access Journals (Sweden)

    Brüning Thomas

    2009-11-01

    Full Text Available Abstract Background The collection of exhaled breath condensate (EBC is a suitable and non-invasive method for evaluation of airway inflammation. Several studies indicate that the composition of the condensate and the recovery of biomarkers are affected by physical characteristics of the condensing device and collecting circumstances. Additionally, there is an apparent influence of the condensing temperature, and often the level of detection of the assay is a limiting factor. The ECoScreen2 device is a new, partly single-use disposable system designed for studying different lung compartments. Methods EBC samples were collected from 16 healthy non-smokers by using the two commercially available devices ECoScreen2 and ECoScreen at a controlled temperature of -20°C. EBC volume, pH, NOx, LTB4, PGE2, 8-isoprostane and cys-LTs were determined. Results EBC collected with ECoScreen2 was less acidic compared to ECoScreen. ECoScreen2 was superior concerning condensate volume and detection of biomarkers, as more samples were above the detection limit (LTB4 and PGE2 or showed higher concentrations (8-isoprostane. However, NOx was detected only in EBC sampled by ECoScreen. Conclusion ECoScreen2 in combination with mediator specific enzyme immunoassays may be suitable for measurement of different biomarkers. Using this equipment, patterns of markers can be assessed that are likely to reflect the complex pathophysiological processes in inflammatory respiratory disease.

  3. An efficient contents-adaptive backlight control method for mobile devices

    Science.gov (United States)

    Chen, Qiao Song; Yan, Ya Xing; Zhang, Xiao Mou; Cai, Hua; Deng, Xin; Wang, Jin

    2015-03-01

    For most of mobile devices with a large screen, image quality and power consumption are both of the major factors affecting the consumers' preference. Contents-adaptive backlight control (CABC) method can be utilized to adjust the backlight and promote the performance of mobile devices. Unlike the previous works mostly focusing on the reduction of power consumption, both of image quality and power consumption are taken into account in the proposed method. Firstly, region of interest (ROI) is detected to divide image into two parts: ROI and non-ROI. Then, three attributes including entropy, luminance, and saturation information in ROI are calculated. To achieve high perceived image quality in mobile devices, optimal value of backlight can be calculated by a linear combination of the aforementioned attributes. Coefficients of the linear combination are determined by applying the linear regression to the subjective scores of human visual experiments and objective values of the attributes. Based on the optimal value of backlight, displayed image data are processed brightly and backlight is darkened to reduce the power consumption of backlight later. Here, the ratios of increasing image data and decreasing backlight functionally depend on the luminance information of displayed image. Also, the proposed method is hardware implemented. Experimental results indicate that the proposed technique exhibits better performance compared to the conventional methods.

  4. Increasing operational command and control security by the implementation of device independent quantum key distribution

    Science.gov (United States)

    Bovino, Fabio Antonio; Messina, Angelo

    2016-10-01

    In a very simplistic way, the Command and Control functions can be summarized as the need to provide the decision makers with an exhaustive, real-time, situation picture and the capability to convey their decisions down to the operational forces. This two-ways data and information flow is vital to the execution of current operations and goes far beyond the border of military operations stretching to Police and disaster recovery as well. The availability of off-the shelf technology has enabled hostile elements to endanger the security of the communication networks by violating the traditional security protocols and devices and hacking sensitive databases. In this paper an innovative approach based to implementing Device Independent Quantum Key Distribution system is presented. The use of this technology would prevent security breaches due to a stolen crypto device placed in an end-to-end communication chain. The system, operating with attenuated laser, is practical and provides the increasing of the distance between the legitimate users.

  5. Embedded Control in Wearable Medical Devices: Application to the Artificial Pancreas

    Directory of Open Access Journals (Sweden)

    Stamatina Zavitsanou

    2016-09-01

    Full Text Available Significant increases in processing power, coupled with the miniaturization of processing units operating at low power levels, has motivated the embedding of modern control systems into medical devices. The design of such embedded decision-making strategies for medical applications is driven by multiple crucial factors, such as: (i guaranteed safety in the presence of exogenous disturbances and unexpected system failures; (ii constraints on computing resources; (iii portability and longevity in terms of size and power consumption; and (iv constraints on manufacturing and maintenance costs. Embedded control systems are especially compelling in the context of modern artificial pancreas systems (AP used in glucose regulation for patients with type 1 diabetes mellitus (T1DM. Herein, a review of potential embedded control strategies that can be leveraged in a fully-automated and portable AP is presented. Amongst competing controllers, emphasis is provided on model predictive control (MPC, since it has been established as a very promising control strategy for glucose regulation using the AP. Challenges involved in the design, implementation and validation of safety-critical embedded model predictive controllers for the AP application are discussed in detail. Additionally, the computational expenditure inherent to MPC strategies is investigated, and a comparative study of runtime performances and storage requirements among modern quadratic programming solvers is reported for a desktop environment and a prototype hardware platform.

  6. A portable hardware-in-the-loop (HIL) device for automotive diagnostic control systems.

    Science.gov (United States)

    Palladino, A; Fiengo, G; Lanzo, D

    2012-01-01

    In-vehicle driving tests for evaluating the performance and diagnostic functionalities of engine control systems are often time consuming, expensive, and not reproducible. Using a hardware-in-the-loop (HIL) simulation approach, new control strategies and diagnostic functions on a controller area network (CAN) line can be easily tested in real time, in order to reduce the effort and the cost of the testing phase. Nowadays, spark ignition engines are controlled by an electronic control unit (ECU) with a large number of embedded sensors and actuators. In order to meet the rising demand of lower emissions and fuel consumption, an increasing number of control functions are added into such a unit. This work aims at presenting a portable electronic environment system, suited for HIL simulations, in order to test the engine control software and the diagnostic functionality on a CAN line, respectively, through non-regression and diagnostic tests. The performances of the proposed electronic device, called a micro hardware-in-the-loop system, are presented through the testing of the engine management system software of a 1.6 l Fiat gasoline engine with variable valve actuation for the ECU development version. Copyright © 2011 ISA. Published by Elsevier Ltd. All rights reserved.

  7. From nanofabrication to self-fabrication--tailored chemistry for control of single molecule electronic devices

    DEFF Research Database (Denmark)

    Moth-Poulsen, Kasper; Bjørnholm, Thomas

    2010-01-01

    Single molecule electronics is a field of research focused on the use of single molecules as electronics components. During the past 15 years the field has concentrated on development of test beds for measurements on single molecules. Bottom-up approaches to single molecule devices are emerging...... the electronic properties of a single molecule by chemical design....... as alternatives to the dominant top-down nanofabrication techniques. One example is solution-based self-assembly of a molecule enclosed by two gold nanorod electrodes. This article will discuss recent attempts to control the self-assembly process by the use of supramolecular chemistry and how to tailor...

  8. Amplitude Test for Input Devices for System Control in Immersive Virtual Environment

    DEFF Research Database (Denmark)

    Stenholt, Rasmus; Thornemann Hansen, Nina; Hald, Kasper

    2014-01-01

    In this study, the amplitudes best suited to compare four input devices are examined in the context of a pointer-based system control interface for immersive virtual environments. The interfaces are based on a pen and tablet, a touch tablet, hand-tracking using Kinect and a Wii Nunchuk analog stick...... menu using each combination of amplitude and interface. The amplitudes to be used for future experiments were found. Also, the movement times for the interfaces do not fit the predictions of Fitts' law....

  9. Modeling and control of a brushless DC axial flow ventricular assist device.

    Science.gov (United States)

    Giridharan, Guruprasad A; Skliar, Mikhail; Olsen, Donald B; Pantalos, George M

    2002-01-01

    This article presents an integrated model of the human circulatory system that incorporates circulatory support by a brushless DC axial flow ventricular assist device (VAD), and a feedback VAD controller designed to maintain physiologically sufficient perfusion. The developed integrated model combines a network type model of the circulatory system with a nonlinear dynamic model of the brushless DC pump We show that maintaining a reference differential pressure between the left ventricle and aorta leads to adequate perfusion for different pathologic cases, ranging from normal heart to left heart asystole, and widely varying physical activity scenarios from rest to exercise.

  10. Integrated Lateral Flow Device for Flow Control with Blood Separation and Biosensing

    Directory of Open Access Journals (Sweden)

    Veronica Betancur

    2017-12-01

    Full Text Available Lateral flow devices are versatile and serve a wide variety of purposes, including medical, agricultural, environmental, and military applications. Yet, the most promising opportunities of these devices for diagnosis might reside in point-of-care (POC applications. Disposable paper-based lateral flow strips have been of particular interest, because they utilize low-cost materials and do not require expensive fabrication instruments. However, there are constraints on tuning flow rates and immunoassays functionalization in papers, as well as technical challenges in sensors’ integration and concentration units for low-abundant molecular detection. In the present work, we demonstrated an integrated lateral flow device that applied the capillary forces with functionalized polymer-based microfluidics as a strategy to realize a portable, simplified, and self-powered lateral flow device (LFD. The polydimethylsiloxane (PDMS surface was rendered hydrophilic via functionalization with different concentrations of Pluronic F127. Controlled flow is a key variable for immunoassay-based applications for providing enough time for protein binding to antibodies. The flow rate of the integrated LFD was regulated by the combination of multiple factors, including Pluronic F127 functionalized surface properties and surface treatments of microchannels, resistance of the integrated flow resistor, the dimensions of the microstructures and the spacing between them in the capillary pump, the contact angles, and viscosity of the fluids. Various plasma flow rates were regulated and achieved in the whole device. The LFD combined the ability to separate high quality plasma from human whole blood by using a highly asymmetric plasma separation membrane, and created controlled and steady fluid flow using capillary forces produced by the interfacial tensions. Biomarker immunoglobulin G (IgG detection from plasma was demonstrated with a graphene nanoelectronic sensor integrated

  11. Standardising visual control devices for tsetse flies: Central and West African species Glossina palpalis palpalis.

    Science.gov (United States)

    Kaba, Dramane; Zacarie, Tusevo; M'pondi, Alexis Makumyaviri; Njiokou, Flobert; Bosson-Vanga, Henriette; Kröber, Thomas; McMullin, Andrew; Mihok, Steve; Guerin, Patrick M

    2014-01-01

    Glossina palpalis palpalis (G. p. palpalis) is one of the principal vectors of sleeping sickness and nagana in Africa with a geographical range stretching from Liberia in West Africa to Angola in Central Africa. It inhabits tropical rain forest but has also adapted to urban settlements. We set out to standardize a long-lasting, practical and cost-effective visually attractive device that would induce the strongest landing response by G. p. palpalis for future use as an insecticide-impregnated tool in area-wide population suppression of this fly across its range. Trials were conducted in wet and dry seasons in the Ivory Coast, Cameroon, the Democratic Republic of Congo and Angola to measure the performance of traps (biconical, monoconical and pyramidal) and targets of different sizes and colours, with and without chemical baits, at different population densities and under different environmental conditions. Adhesive film was used as a practical enumerator at these remote locations to compare landing efficiencies of devices. Independent of season and country, both phthalogen blue-black and blue-black-blue 1 m(2) targets covered with adhesive film proved to be as good as traps in phthalogen blue or turquoise blue for capturing G. p. palpalis. Trap efficiency varied (8-51%). There was no difference between the performance of blue-black and blue-black-blue 1 m(2) targets. Baiting with chemicals augmented the overall performance of targets relative to traps. Landings on smaller phthalogen blue-black 0.25 m(2) square targets were not significantly different from either 1 m(2) blue-black-blue or blue-black square targets. Three times more flies were captured per unit area on the smaller device. Blue-black 0.25 m(2) cloth targets show promise as simple cost effective devices for management of G. p. palpalis as they can be used for both control when impregnated with insecticide and for population sampling when covered with adhesive film.

  12. Survey of Emissions Associated with Enclosed Combustor Emission Control Devices in the Denver-Julesburg Basin

    Science.gov (United States)

    Knighton, W. B.; Floerchinger, C. R.; Wormhoult, J.; Massoli, P.; Fortner, E.; Brooks, B.; Roscioli, J. R.; Bon, D.; Herndon, S. C.

    2014-12-01

    Volatile organic compounds (VOCs) play an important role in local and regional air quality. A large source of VOCs comes from the oil and gas industry and the Denver-Julesburg Basin (D-J Basin) has seen a sharp increase in production in recent years primarily due to advances in horizontal drilling techniques. To help curb emissions with extraction and production of natural gas and its associated oil, emission control devices are required for facilities emitting over 6 tons of hydrocarbons per year. Within the ozone non-attainment area, which encompasses Denver and much of the front range, enclosed combustion devices (enclosed flares) are required to reduce hydrocarbon emissions by at least 95%. While certification tests indicate that these enclosed combustor devices provide high destruction removal efficiencies, there is considerable interest in knowing how well they perform in the field. As part of Front Range Air Pollution and Photochemistry Experiment (FRAPPE) project conducted during the Summer of 2014, the Aerodyne Mobile Laboratory (AML) surveyed oil and gas operations within the Wattenberg gas field and the surrounding D-J Basin. The AML deployed a full suite of gas and particle phase instrumentation providing a comprehensive set of on-line, real-time measurements for the major natural gas components (methane and ethane) and their combustion products (CO2, CO, NOx) using a variety of spectroscopic techniques. Additional gas phase organic gas emissions were made using a proton transfer reaction mass spectrometer (PTR-MS). Particle number and composition were determined using a condensation particle counter and an Aerodyne Aerosol Mass Spectrometer (AMS). A summary of the number of enclosed combustor devices measured and their observed combustion efficiencies will be presented.

  13. Current good manufacturing practices, quality control procedures, quality factors, notification requirements, and records and reports, for infant formula. Final rule.

    Science.gov (United States)

    2014-06-10

    The Food and Drug Administration (FDA or we) is issuing a final rule that adopts, with some modifications, the interim final rule (IFR) entitled "Current Good Manufacturing Practices, Quality Control Procedures, Quality Factors, Notification Requirements, and Records and Reports, for Infant Formula'' (February 10, 2014). This final rule affirms the IFR's changes to FDA's regulations and provides additional modifications and clarifications. The final rule also responds to certain comments submitted in response to the request for comments in the IFR.

  14. Design and implementation of fuzzy logic controllers. Thesis Final Report, 27 Jul. 1992 - 1 Jan. 1993

    Science.gov (United States)

    Abihana, Osama A.; Gonzalez, Oscar R.

    1993-01-01

    The main objectives of our research are to present a self-contained overview of fuzzy sets and fuzzy logic, develop a methodology for control system design using fuzzy logic controllers, and to design and implement a fuzzy logic controller for a real system. We first present the fundamental concepts of fuzzy sets and fuzzy logic. Fuzzy sets and basic fuzzy operations are defined. In addition, for control systems, it is important to understand the concepts of linguistic values, term sets, fuzzy rule base, inference methods, and defuzzification methods. Second, we introduce a four-step fuzzy logic control system design procedure. The design procedure is illustrated via four examples, showing the capabilities and robustness of fuzzy logic control systems. This is followed by a tuning procedure that we developed from our design experience. Third, we present two Lyapunov based techniques for stability analysis. Finally, we present our design and implementation of a fuzzy logic controller for a linear actuator to be used to control the direction of the Free Flight Rotorcraft Research Vehicle at LaRC.

  15. Construction and installation of low-cost energy-conservation devices on existing residential structures. Final report

    Energy Technology Data Exchange (ETDEWEB)

    None

    1983-01-01

    Through the Neighborhood Housing Services, Incorporated of Charlotte, a series of hands-on workshops and a demonstration site was provided to enable residents of the Plaza-Midwood Neighborhood to build and install a variety of low-cost, durable, small scale, energy conservation systems. This experimental approach enabled homeowners to apply specific technologies to their own homes. These cost effective measures were designed to encourage both self reliance and the use of renewable resources. The weekend projects included protected entry, numerous moveable window insulation devices, solar air collector/greenhouse, window greenhouse and water storage tubes. The building used for retrofit was the office for the Neighborhood Housing Services (NHS), a non-profit corporation formed to help revitalize residential structures and maintain the economic, racial, and social character of existing neighborhoods. The particular neighborhood involved was Plaza-Midwood and covers approximately a 2 square mile area. The neighborhood housing stock is of the 1910 to 1940 variety with the predominate architectual style being bungalow frame, having 1000 to 1900 square feet in area. The neighborhood is a racially integrated one, with about 70% of the residents being homeowners. An estimated 1700 housing units are in this area. The NHS office presently serves as a resource center for area residents who need loans and/or construction assistance. Providing a continuing educational program is a function of this organization. The Grant provided a significant contribution as a resource for energy conservation mined residents. A resource room displaying procedures and diagrams for the various projects in this proposal was established. Additional resource literature was provided and used by local residents.

  16. [Experience with prosthetic disc nucleus device in Mexico. Final report of a 4-year follow-up].

    Science.gov (United States)

    Rosales-Olivares, Luis Miguel; Pérez-Víquez, Ariel; Miramontes-Martínez, Víctor; Alpízar-Aguirre, Armando; Reyes-Sánchez, Alejandro Antonio

    2007-01-01

    Discal hernia is generally treated by discectomies that are mutilating and cause instability and low back pain in 50% of the patients. Partial arthroplasty is used in an attempt to avoid degeneration after a discectomy. Nineteen patients from the INR (National Institute of Rehabilitation) were selected with extruded discal hernia. All inclusion criteria were met, with a minimal follow-up of 4 years. Evolution was evaluated with the Oswestry scale (OS) and x-ray studies. Statistical analysis was done with Student's t-test. Sixteen men and three women were included in the study, with an average age of 35.4 years. OS before surgery was 57.37% and improved to 22% (p < 0.001). The results obtained in the Prolo scale 4 years later were for the economy scale, p < 0.001 (Wilcoxon Z = 3.87) and for the functional scale, p < 0.001 (Wilcoxon Z = -3.94). The intervertebral space height (IS) before surgery was 6 and 8 mm, and 4 years later, in 12 patients it remained between 8 and 10 mm. The prosthesis had variations according to its initial placement in seven patients, and in all there was subsidence. In two cases migration surpassed the limits of the vertebral body without clinical repercussion. None of the patients required re-operation. Prosthetic disc nucleus device improved clinical conditions and x-rays of the patients using Oswestry, Prolo and intersomatic space height enhancement after 4 years of follow-up in 12/19 patients.

  17. Stability effects of singularities in force-controlled robotic assist devices

    Science.gov (United States)

    Luecke, Greg R.

    2002-02-01

    Force feedback is being used as an interface between humans and material handling equipment to provide an intuitive method to control large and bulky payloads. Powered actuation in the lift assist device compensates for the inertial characteristics of the manipulator and the payload to provide effortless control and handling of manufacturing parts, components, and assemblies. The use of these Intelligent Assist Devices (IAD) is being explored to prevent worker injury, enhance material handling performance, and increase productivity in the workplace. The IAD also provides the capability to shape and control motion in the workspace during routine operations. Virtual barriers can be developed to protect fixed objects in the workspace, and regions can be programmed that attract the work piece to a certain position and orientation. However, the robot is still under complete control of the human operator, with the trajectory being determined and commanded using the judgment of the operator to complete a given task. In many cases, the IAD is built in a configuration that may have singular points inside the workspace. These singularities can cause problems when the unstructured trajectory commands from the human cause interaction between the IAD and the virtual walls and fixtures at positions close to these singularities. The research presented here explores the stability effects of the interactions between the powered manipulator and the virtual surfaces when controlled by the operator. Because of the flexible nature of the human decisions determining the real time work piece paths, manipulator singularities that occur in conjunction with the virtual surfaces raise stability issues in the performance around these singularities. We examine these stability issues in the context of a particular IAD configuration, and present analytic results for the performance and stability of these systems in response to the real-time trajectory modification of the human operator.

  18. Silicon Carbide Semiconductor Surface Dielectric Barrier Discharge (SSDBD) Device for Turbulent Skin Friction Drag Reduction and Flow Control Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The proposed research effort explores the use of a nanosecond pulse driven offset semiconducting surface dielectric barrier discharge (SSDBD) device for the control...

  19. High-performance computing-based exploration of flow control with micro devices.

    Science.gov (United States)

    Fujii, Kozo

    2014-08-13

    The dielectric barrier discharge (DBD) plasma actuator that controls flow separation is one of the promising technologies to realize energy savings and noise reduction of fluid dynamic systems. However, the mechanism for controlling flow separation is not clearly defined, and this lack of knowledge prevents practical use of this technology. Therefore, large-scale computations for the study of the DBD plasma actuator have been conducted using the Japanese Petaflops supercomputer 'K' for three different Reynolds numbers. Numbers of new findings on the control of flow separation by the DBD plasma actuator have been obtained from the simulations, and some of them are presented in this study. Knowledge of suitable device parameters is also obtained. The DBD plasma actuator is clearly shown to be very effective for controlling flow separation at a Reynolds number of around 10(5), and several times larger lift-to-drag ratio can be achieved at higher angles of attack after stall. For higher Reynolds numbers, separated flow is partially controlled. Flow analysis shows key features towards better control. DBD plasma actuators are a promising technology, which could reduce fuel consumption and contribute to a green environment by achieving high aerodynamic performance. The knowledge described above can be obtained only with high-end computers such as the supercomputer 'K'. © 2014 The Author(s) Published by the Royal Society. All rights reserved.

  20. Standardizing visual control devices for tsetse flies: east African Species Glossina fuscipes fuscipes and Glossina tachinoides.

    Science.gov (United States)

    Oloo, Francis; Sciarretta, Andrea; Mohamed-Ahmed, Mohamed M; Kröber, Thomas; McMullin, Andrew; Mihok, Steve; Guerin, Patrick M

    2014-11-01

    Riverine species of tsetse are responsible for most human African trypanosomiasis (HAT) transmission and are also important vectors of animal trypanosomiasis. This study concerns the development of visual control devices for two such species, Glossina fuscipes fuscipes and Glossina tachinoides, at the eastern limits of their continental range. The goal was to determine the most long-lasting, practical and cost-effective visually attractive device that induces the strongest landing responses in these species for use as insecticide-impregnated tools in vector population suppression. Field trials were conducted in different seasons on G. f. fuscipes in Kenya, Ethiopia and the Sudan and on G. tachinoides in Ethiopia to measure the performance of traps and 2D targets of different sizes and colours, with and without chemical baits, at different population densities and under different environmental conditions. Adhesive film was used to enumerate flies at these remote locations to compare trapping efficiencies. The findings show that targets made from black and blue fabrics (either phthalogen or turquoise) covered with adhesive film render them equal to or more efficient than traps at capturing G. f. fuscipes and G. tachinoides. Biconical trap efficiency varied between 25% and 33% for the two species. Smaller 0.25 m×0.25 m phthalogen blue-black targets proved more efficient than the regular 1 m2 target for both species, by over six times for Glossina f. fuscipes and two times for G. tachinoides based on catches per m2. Overall, targets with a higher edge/surface area ratio were more efficient at capturing flies. Taking into account practical considerations and fly preferences for edges and colours, we propose a 0.5×0.75 m blue-black target as a simple cost-effective device for management of G. f. fuscipes and G. tachinoides, impregnated with insecticide for control and covered with adhesive film for population sampling.

  1. Standardizing visual control devices for tsetse flies: east African Species Glossina fuscipes fuscipes and Glossina tachinoides.

    Directory of Open Access Journals (Sweden)

    Francis Oloo

    2014-11-01

    Full Text Available Riverine species of tsetse are responsible for most human African trypanosomiasis (HAT transmission and are also important vectors of animal trypanosomiasis. This study concerns the development of visual control devices for two such species, Glossina fuscipes fuscipes and Glossina tachinoides, at the eastern limits of their continental range. The goal was to determine the most long-lasting, practical and cost-effective visually attractive device that induces the strongest landing responses in these species for use as insecticide-impregnated tools in vector population suppression.Field trials were conducted in different seasons on G. f. fuscipes in Kenya, Ethiopia and the Sudan and on G. tachinoides in Ethiopia to measure the performance of traps and 2D targets of different sizes and colours, with and without chemical baits, at different population densities and under different environmental conditions. Adhesive film was used to enumerate flies at these remote locations to compare trapping efficiencies. The findings show that targets made from black and blue fabrics (either phthalogen or turquoise covered with adhesive film render them equal to or more efficient than traps at capturing G. f. fuscipes and G. tachinoides. Biconical trap efficiency varied between 25% and 33% for the two species. Smaller 0.25 m×0.25 m phthalogen blue-black targets proved more efficient than the regular 1 m2 target for both species, by over six times for Glossina f. fuscipes and two times for G. tachinoides based on catches per m2. Overall, targets with a higher edge/surface area ratio were more efficient at capturing flies.Taking into account practical considerations and fly preferences for edges and colours, we propose a 0.5×0.75 m blue-black target as a simple cost-effective device for management of G. f. fuscipes and G. tachinoides, impregnated with insecticide for control and covered with adhesive film for population sampling.

  2. WaveSAX device: design optimization through scale modelling and a PTO strategical control system

    Science.gov (United States)

    Peviani, Maximo; Danelli, Andrea; Dadone, Gianluca; Dalmasso, Alberto

    2017-04-01

    WaveSAX is an innovative OWC (Oscillating Water Column) device for the generation of electricity from wave power, conceived to be installed in coastal marine structures, such as ports and harbours. The device - especially designed for the typical wave climate of Mediterranean Sea - is characterized by two important aspects: flexibility to fit in different structural configurations and replication in a large number of units. A model of the WaveSAX device on a scale 1:5 has been built and tested in the ocean tank at Ecole Centrale de Nantes (France). The study aimed to analyse the behaviour of the device, including two Wells turbine configurations (with three and four blades), with regular and irregular wave conditions in the ocean wave tank. The model and the wave basin were equipped with a series of sensors which allowed to measure the following parameters during the tests: pressure in different points inside the device, the free water surface displacement inside and outside the device, the rotational velocity and the torque at the top of the axis. The tests had the objective to optimize the device design, especially as far as the characteristics of the rotor of the turbine is concern. Although the performance of the WaveSAX has been satisfactory for regular wave conditions, the behaviour of the Wells turbines for irregular wave climate has shown limitations in terms of maintaining the capacity to transform hydraulics energy into mechanical power. To optimize the efficiency of the turbine, an electronical system has been built on the basis of the ocean tank tests. It allows to continuously monitor and command the rotational speed and the torque of the rotor connected with the turbine, and to control in real time the electrical flow of a motor-generator, either absorbing energy as a generator, or providing power to the turbine working as an engine. Two strategies - based on the velocity and the torque control - have been investigate in the electronic test bench

  3. Precision Control of Thermal Transport in Cryogenic Single-Crystal Silicon Devices

    Science.gov (United States)

    Rostem, K.; Chuss, D. T.; Colazo, F. A.; Crowe, E. J.; Denis, K. L.; Lourie, N. P.; Moseley, S. H.; Stevenson, T. R.; Wollack, E. J.

    2014-01-01

    We report on the diffusive-ballistic thermal conductance of multi-moded single-crystal silicon beams measured below 1 K. It is shown that the phonon mean-free-path is a strong function of the surface roughness characteristics of the beams. This effect is enhanced in diffuse beams with lengths much larger than, even when the surface is fairly smooth, 510 nm rms, and the peak thermal wavelength is 0.6 microns. Resonant phonon scattering has been observed in beams with a pitted surface morphology and characteristic pit depth of 30 nm. Hence, if the surface roughness is not adequately controlled, the thermal conductance can vary significantly for diffuse beams fabricated across a wafer. In contrast, when the beam length is of order, the conductance is dominated by ballistic transport and is effectively set by the beam cross-sectional area. We have demonstrated a uniformity of +/-8% in fractional deviation for ballistic beams, and this deviation is largely set by the thermal conductance of diffuse beams that support the micro-electro-mechanical device and electrical leads. In addition, we have found no evidence for excess specific heat in single-crystal silicon membranes. This allows for the precise control of the device heat capacity with normal metal films. We discuss the results in the context of the design and fabrication of large-format arrays of far-infrared and millimeter wavelength cryogenic detectors.

  4. Control of a powered prosthetic device via a pinch gesture interface

    Science.gov (United States)

    Yetkin, Oguz; Wallace, Kristi; Sanford, Joseph D.; Popa, Dan O.

    2015-06-01

    A novel system is presented to control a powered prosthetic device using a gesture tracking system worn on a user's sound hand in order to detect different grasp patterns. Experiments are presented with two different gesture tracking systems: one comprised of Conductive Thimbles worn on each finger (Conductive Thimble system), and another comprised of a glove which leaves the fingers free (Conductive Glove system). Timing tests were performed on the selection and execution of two grasp patterns using the Conductive Thimble system and the iPhone app provided by the manufacturer. A modified Box and Blocks test was performed using Conductive Glove system and the iPhone app provided by Touch Bionics. The best prosthetic device performance is reported with the developed Conductive Glove system in this test. Results show that these low encumbrance gesture-based wearable systems for selecting grasp patterns may provide a viable alternative to EMG and other prosthetic control modalities, especially for new prosthetic users who are not trained in using EMG signals.

  5. Integrated emissions control system for residential CWS furnace. Final report, September 20, 1989--March 20, 1993

    Energy Technology Data Exchange (ETDEWEB)

    Breault, R.W.; McLarnon, C.

    1993-03-01

    One of the major obstacles to the successful development and commercialization of a coal-fired residential furnace is the need for a reliable, cost-effective emission control system. Tecogen is developing a novel, integrated control system to control NO{sub x}SO{sub 2}, and particulate emissions. At the heart of this system is a unique emissions control reactor for the control of SO{sub 2}. This reactor provides high sorbent particle residence time within the reactor while doing so in a very compact geometry. Final cleanup of any fine particulates exiting the reactor including respirable-sized particulates, is completed with the use of high efficiency bag filters. Under a previous contract with PETC (Contract No. DE-AC22-87PC79650), Tecogen developed a residential-scale Coal Water Slurry (CWS) combustor to control NO{sub x}emission. This combustor makes use of centrifugal forces, set up by a predominantly tangential flow field, to separate and confine larger unburned coal particles in the furnace upper chamber. Various partitions are used to retard the axial, downward flow of these particles, and thus maximize their residence time in the hottest section of the combustor. By operating this combustor under staged conditions, the local stoichiometry in the primary zone can be controlled in such a manner as to minimize NO{sub x} emission.

  6. Optimal control problems with switching points. Ph.D. Thesis, 1990 Final Report

    Science.gov (United States)

    Seywald, Hans

    1991-01-01

    An overview is presented of the problems and difficulties that arise in solving optimal control problems with switching points. A brief discussion of existing optimality conditions is given and a numerical approach for solving the multipoint boundary value problems associated with the first-order necessary conditions of optimal control is presented. Two real-life aerospace optimization problems are treated explicitly. These are altitude maximization for a sounding rocket (Goddard Problem) in the presence of a dynamic pressure limit, and range maximization for a supersonic aircraft flying in the vertical, also in the presence of a dynamic pressure limit. In the second problem singular control appears along arcs with active dynamic pressure limit, which in the context of optimal control, represents a first-order state inequality constraint. An extension of the Generalized Legendre-Clebsch Condition to the case of singular control along state/control constrained arcs is presented and is applied to the aircraft range maximization problem stated above. A contribution to the field of Jacobi Necessary Conditions is made by giving a new proof for the non-optimality of conjugate paths in the Accessory Minimum Problem. Because of its simple and explicit character, the new proof may provide the basis for an extension of Jacobi's Necessary Condition to the case of the trajectories with interior point constraints. Finally, the result that touch points cannot occur for first-order state inequality constraints is extended to the case of vector valued control functions.

  7. Stabilization and control of quad-rotor helicopter using a smartphone device

    Science.gov (United States)

    Desai, Alok; Lee, Dah-Jye; Moore, Jason; Chang, Yung-Ping

    2013-01-01

    In recent years, autonomous, micro-unmanned aerial vehicles (micro-UAVs), or more specifically hovering micro- UAVs, have proven suitable for many promising applications such as unknown environment exploration and search and rescue operations. The early versions of UAVs had no on-board control capabilities, and were difficult for manual control from a ground station. Many UAVs now are equipped with on-board control systems that reduce the amount of control required from the ground-station operator. However, the limitations on payload, power consumption and control without human interference remain the biggest challenges. This paper proposes to use a smartphone as the sole computational device to stabilize and control a quad-rotor. The goal is to use the readily available sensors in a smartphone such as the GPS, the accelerometer, the rate-gyros, and the camera to support vision-related tasks such as flight stabilization, estimation of the height above ground, target tracking, obstacle detection, and surveillance. We use a quad-rotor platform that has been built in the Robotic Vision Lab at Brigham Young University for our development and experiments. An Android smartphone is connected through the USB port to an external hardware that has a microprocessor and circuitries to generate pulse-width modulation signals to control the brushless servomotors on the quad-rotor. The high-resolution camera on the smartphone is used to detect and track features to maintain a desired altitude level. The vision algorithms implemented include template matching, Harris feature detector, RANSAC similarity-constrained homography, and color segmentation. Other sensors are used to control yaw, pitch, and roll of the quad-rotor. This smartphone-based system is able to stabilize and control micro-UAVs and is ideal for micro-UAVs that have size, weight, and power limitations.

  8. Photoluminescence-based quality control for thin film absorber layers of photovoltaic devices

    Science.gov (United States)

    Repins, Ingrid L.; Kuciauskas, Darius

    2015-07-07

    A time-resolved photoluminescence-based system providing quality control during manufacture of thin film absorber layers for photovoltaic devices. The system includes a laser generating excitation beams and an optical fiber with an end used both for directing each excitation beam onto a thin film absorber layer and for collecting photoluminescence from the absorber layer. The system includes a processor determining a quality control parameter such as minority carrier lifetime of the thin film absorber layer based on the collected photoluminescence. In some implementations, the laser is a low power, pulsed diode laser having photon energy at least great enough to excite electron hole pairs in the thin film absorber layer. The scattered light may be filterable from the collected photoluminescence, and the system may include a dichroic beam splitter and a filter that transmit the photoluminescence and remove scattered laser light prior to delivery to a photodetector and a digital oscilloscope.

  9. Method of Optimizing the Construction of Machining, Assembly and Control Devices

    Science.gov (United States)

    Iordache, D. M.; Costea, A.; Niţu, E. L.; Rizea, A. D.; Babă, A.

    2017-10-01

    Industry dynamics, driven by economic and social requirements, must generate more interest in technological optimization, capable of ensuring a steady development of advanced technical means to equip machining processes. For these reasons, the development of tools, devices, work equipment and control, as well as the modernization of machine tools, is the certain solution to modernize production systems that require considerable time and effort. This type of approach is also related to our theoretical, experimental and industrial applications of recent years, presented in this paper, which have as main objectives the elaboration and use of mathematical models, new calculation methods, optimization algorithms, new processing and control methods, as well as some structures for the construction and configuration of technological equipment with a high level of performance and substantially reduced costs..

  10. 40 CFR 63.496 - Back-end process provisions-procedures to determine compliance using control or recovery devices.

    Science.gov (United States)

    2010-07-01

    ... process vent streams are combined prior to being routed to control or recovery devices, the inlet sampling... boiler or process heater. (iii) The control efficiency of the boiler or process heater shall be calculated using Equation 29. ER05SE96.027 where: R=Control efficiency of boiler or process heater, percent...

  11. 40 CFR 63.4965 - How do I determine the add-on control device emission destruction or removal efficiency?

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 12 2010-07-01 2010-07-01 true How do I determine the add-on control... Coating of Metal Furniture Compliance Requirements for the Emission Rate with Add-on Controls Option § 63.4965 How do I determine the add-on control device emission destruction or removal efficiency? You must...

  12. 40 CFR 63.4566 - How do I determine the add-on control device emission destruction or removal efficiency?

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 12 2010-07-01 2010-07-01 true How do I determine the add-on control... Surface Coating of Plastic Parts and Products Compliance Requirements for the Emission Rate with Add-on Controls Option § 63.4566 How do I determine the add-on control device emission destruction or removal...

  13. 40 CFR 63.4166 - How do I determine the add-on control device emission destruction or removal efficiency?

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 12 2010-07-01 2010-07-01 true How do I determine the add-on control... Coating of Large Appliances Compliance Requirements for the Emission Rate with Add-on Controls Option § 63.4166 How do I determine the add-on control device emission destruction or removal efficiency? (a) For...

  14. 40 CFR 63.3545 - How do I determine the add-on control device emission destruction or removal efficiency?

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 12 2010-07-01 2010-07-01 true How do I determine the add-on control... Coating of Metal Cans Compliance Requirements for the Emission Rate with Add-on Controls Option § 63.3545 How do I determine the add-on control device emission destruction or removal efficiency? You must use...

  15. 40 CFR 63.4766 - How do I determine the add-on control device emission destruction or removal efficiency?

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 12 2010-07-01 2010-07-01 true How do I determine the add-on control... Coating of Wood Building Products Compliance Requirements for the Emission Rate with Add-on Controls Option § 63.4766 How do I determine the add-on control device emission destruction or removal efficiency...

  16. The Use of a Brain Computer Interface Remote Control to Navigate a Recreational Device

    Directory of Open Access Journals (Sweden)

    Shih Chung Chen

    2013-01-01

    Full Text Available People suffering from paralysis caused by serious neural disorder or spinal cord injury also need to be given a means of recreation other than general living aids. Although there have been a proliferation of brain computer interface (BCI applications, developments for recreational activities are scarcely seen. The objective of this study is to develop a BCI-based remote control integrated with commercial devices such as the remote controlled Air Swimmer. The brain is visually stimulated using boxes flickering at preprogrammed frequencies to activate a brain response. After acquiring and processing these brain signals, the frequency of the resulting peak, which corresponds to the user’s selection, is determined by a decision model. Consequently, a command signal is sent from the computer to the wireless remote controller via a data acquisition (DAQ module. A command selection training (CST and simulated path test (SPT were conducted by 12 subjects using the BCI control system and the experimental results showed a recognition accuracy rate of 89.51% and 92.31% for the CST and SPT, respectively. The fastest information transfer rate demonstrated a response of 105 bits/min and 41.79 bits/min for the CST and SPT, respectively. The BCI system was proven to be able to provide a fast and accurate response for a remote controller application.

  17. A cerebellar model for predictive motor control tested in a brain-based device.

    Science.gov (United States)

    McKinstry, Jeffrey L; Edelman, Gerald M; Krichmar, Jeffrey L

    2006-02-28

    The cerebellum is known to be critical for accurate adaptive control and motor learning. We propose here a mechanism by which the cerebellum may replace reflex control with predictive control. This mechanism is embedded in a learning rule (the delayed eligibility trace rule) in which synapses onto a Purkinje cell or onto a cell in the deep cerebellar nuclei become eligible for plasticity only after a fixed delay from the onset of suprathreshold presynaptic activity. To investigate the proposal that the cerebellum is a general-purpose predictive controller guided by a delayed eligibility trace rule, a computer model based on the anatomy and dynamics of the cerebellum was constructed. It contained components simulating cerebellar cortex and deep cerebellar nuclei, and it received input from a middle temporal visual area and the inferior olive. The model was incorporated in a real-world brain-based device (BBD) built on a Segway robotic platform that learned to traverse curved paths. The BBD learned which visual motion cues predicted impending collisions and used this experience to avoid path boundaries. During learning, the BBD adapted its velocity and turning rate to successfully traverse various curved paths. By examining neuronal activity and synaptic changes during this behavior, we found that the cerebellar circuit selectively responded to motion cues in specific receptive fields of simulated middle temporal visual areas. The system described here prompts several hypotheses about the relationship between perception and motor control and may be useful in the development of general-purpose motor learning systems for machines.

  18. 40 CFR 63.3546 - How do I establish the emission capture system and add-on control device operating limits during...

    Science.gov (United States)

    2010-07-01

    ... system and add-on control device operating limits during the performance test? 63.3546 Section 63.3546... device or system of multiple capture devices. The average duct static pressure is the maximum operating... Add-on Controls Option § 63.3546 How do I establish the emission capture system and add-on control...

  19. NERI PROJECT 99-119. TASK 1. ADVANCED CONTROL TOOLS AND METHODS. FINAL REPORT

    Energy Technology Data Exchange (ETDEWEB)

    March-Leuba, J.A.

    2002-09-09

    Nuclear plants of the 21st century will employ higher levels of automation and fault tolerance to increase availability, reduce accident risk, and lower operating costs. Key developments in control algorithms, fault diagnostics, fault tolerance, and communication in a distributed system are needed to implement the fully automated plant. Equally challenging will be integrating developments in separate information and control fields into a cohesive system, which collectively achieves the overall goals of improved performance, safety, reliability, maintainability, and cost-effectiveness. Under the Nuclear Energy Research Initiative (NERI), the U. S. Department of Energy is sponsoring a project to address some of the technical issues involved in meeting the long-range goal of 21st century reactor control systems. This project, ''A New Paradigm for Automated Development Of Highly Reliable Control Architectures For Future Nuclear Plants,'' involves researchers from Oak Ridge National Laboratory, University of Tennessee, and North Carolina State University. This paper documents a research effort to develop methods for automated generation of control systems that can be traced directly to the design requirements. Our final goal is to allow the designer to specify only high-level requirements and stress factors that the control system must survive (e.g. a list of transients, or a requirement to withstand a single failure.) To this end, the ''control engine'' automatically selects and validates control algorithms and parameters that are optimized to the current state of the plant, and that have been tested under the prescribed stress factors. The control engine then automatically generates the control software from validated algorithms. Examples of stress factors that the control system must ''survive'' are: transient events (e.g., set-point changes, or expected occurrences such a load rejection,) and postulated

  20. Continuously tunable devices based on electrical control of dual-frequency liquid crystal filled photonic bandgap fibers

    DEFF Research Database (Denmark)

    Scolari, Lara; Alkeskjold, Thomas Tanggaard; Riishede, Jesper

    2005-01-01

    We present an electrically controlled photonic bandgap fiber device obtained by infiltrating the air holes of a photonic crystal fiber (PCF) with a dual-frequency liquid crystal (LC) with pre-tilted molecules. Compared to previously demonstrated devices of this kind, the main new feature...... of this one is its continuous tunability due to the fact that the used LC does not exhibit reverse tilt domain defects and threshold effects. Furthermore, the dual-frequency features of the LC enables electrical control of the spectral position of the bandgaps towards both shorter and longer wavelengths...... in the same device. We investigate the dynamics of this device and demonstrate a birefringence controller based on this principle....

  1. Final Report: Interphase Analysis and Control in Fiber Reinforced Thermoplastic Composites

    Energy Technology Data Exchange (ETDEWEB)

    Jon J. Kellar; William M. Cross; Lidvin Kjerengtroen

    2009-03-14

    This research program builds upon a multi-disciplinary effort in interphase analysis and control in thermoplastic matrix polymer matrix composites (PMC). The research investigates model systems deemed of interest by members of the Automotive Composites Consortium (ACC) as well as samples at the forefront of PMC process development (DRIFT and P4 technologies). Finally, the research investigates, based upon the fundamental understanding of the interphases created during the fabrication of thermoplastic PMCs, the role the interphase play in key bulk properties of interest to the automotive industry.

  2. Physics of semiconductor devices

    Energy Technology Data Exchange (ETDEWEB)

    Prew, B.A.

    1975-09-01

    The properties of semiconductors which make them important in the electronic devices industry, and how these properties are controlled by doping, are described. The physics and applications of p-n and other junction devices, and of bulk effect devices are discussed. Avalanche devices, optical devices, solar cells, Schottky barriers, MOS devices, heterojunctions, photoconductors, and transferred electron devices are considered.

  3. The use of an electronic portal imaging device for exit dosimetry and quality control measurements.

    Science.gov (United States)

    Kirby, M C; Williams, P C

    1995-02-01

    To determine ways in which electronic portal imaging devices (EPIDs) could be used to (a) measure exit doses for external beam radiotherapy and (b) perform quality control checks on linear accelerators. When imaging, our fluoroscopic EPID adjusts the gain, offset, and frame acquisition time of the charge coupled device (CCD) camera automatically, to allow for the range of photon transmissions through the patient, and to optimize the signal-to-noise ratio. However, our EPID can be programmed to act as an integrating dosemeter. EPID dosemeter measurements were made for 20 MV photons, for different field sizes and thicknesses of unit density phantom material placed at varying exit surface to detector distances. These were compared with simultaneous Silicon diode exit dose measurements. Our exit dosimetry technique was verified using an anthropomorphic type phantom, and some initial measurements have been made for patients treated with irregularly shaped 20 MV x-ray fields. In this dosimetry mode, our EPID was also used to measure certain quality control parameters, x-ray field flatness, and the verification of segmented intensity modulated field prescriptions. Configured for dosimetry, our EPID exhibited a highly linear response, capable of resolving individual monitor units. Exit doses could be measured to within about 3% of that measured using Silicon diodes. Field flatness was determined to within 1.5% of Farmer dosemeter measurements. Segmented intensity modulated fields can be easily verified. Our EPID has the versatility to assess a range of parameters pertinent to the delivery of high quality, high precision radiotherapy. When configured appropriately, it can measure exit doses in vivo, with reasonable accuracy, perform certain quick quality control checks, and analyze segmented intensity modulated treatment fields.

  4. Controlled power delivery for super-resolution imaging of biological samples using digital micromirror device

    Science.gov (United States)

    Valiya Peedikakkal, Liyana; Cadby, Ashley

    2017-02-01

    Localization based super resolution images of a biological sample is generally achieved by using high power laser illumination with long exposure time which unfortunately increases photo-toxicity of a sample, making super resolution microscopy, in general, incompatible with live cell imaging. Furthermore, the limitation of photobleaching reduces the ability to acquire time lapse images of live biological cells using fluorescence microscopy. Digital Light Processing (DLP) technology can deliver light at grey scale levels by flickering digital micromirrors at around 290 Hz enabling highly controlled power delivery to samples. In this work, Digital Micromirror Device (DMD) is implemented in an inverse Schiefspiegler telescope setup to control the power and pattern of illumination for super resolution microscopy. We can achieve spatial and temporal patterning of illumination by controlling the DMD pixel by pixel. The DMD allows us to control the power and spatial extent of the laser illumination. We have used this to show that we can reduce the power delivered to the sample to allow for longer time imaging in one area while achieving sub-diffraction STORM imaging in another using higher power densities.

  5. Automatic Life Saving Device in Commercial Aircrafts using Feedback Control System

    Directory of Open Access Journals (Sweden)

    Tennyson Samuel John

    2011-11-01

    Full Text Available Several safety devices have filled in the vacuous spaces in commercial airplanes which once did not possess such sophisticated mechanisms. Commercial airplanes have copious amount of instruments and electrical circuits to provide a proper control system inside the plane. A noteworthy invention in the early 80’s is the oxygen masks provided for every passenger during a plane crash or if the airplane is subjected to climatic disturbances while travelling a passenger manually uses the oxygen masks. The oxygen control system in the airplanes has proved very effective in providing an overall safety to the passengers. But the technique given below is far more advanced than the present scenario. A person suffering from a breathing ailment is succumbed to variations in the carbon dioxide levels. Thereby this CO2 is measured and using a feedback control loop, quick actions can be taken in order to provide quick aid to the ailing patient. These are completely automatic and hence it is advanced than the manual oxygen control system presently used in all commercial aircrafts. At the end of the day saving a life is what a humanistic approach is all about.

  6. Advanced turbine systems sensors and controls needs assessment study. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, R.L.; Fry, D.N.; McEvers, J.A.

    1997-02-01

    The Instrumentation and Controls Division of the Oak Ridge National Laboratory performed an assessment of the sensors and controls needs for land-based advanced gas turbines being designed as a part of the Department of Energy`s (DOE`s) Advanced Turbine Systems (ATS) Program for both utility and industrial applications. The assessment included visits to five turbine manufacturers. During these visits, in-depth discussions were held with design and manufacturing staff to obtain their views regarding the need for new sensors and controls for their advanced turbine designs. The Unsteady Combustion Facilities at the Morgantown Energy Technology Center was visited to assess the need for new sensors for gas turbine combustion research. Finally, a workshop was conducted at the South Carolina Energy Research and Development Center which provided a forum for industry, laboratory, and university engineers to discuss and prioritize sensor and control needs. The assessment identified more than 50 different measurement, control, and monitoring needs for advanced turbines that cannot currently be met from commercial sources. While all the identified needs are important, some are absolutely critical to the success of the ATS Program.

  7. Sensitive biomolecule detection in lateral flow assay with a portable temperature-humidity control device.

    Science.gov (United States)

    Choi, Jane Ru; Hu, Jie; Feng, Shangsheng; Wan Abas, Wan Abu Bakar; Pingguan-Murphy, Belinda; Xu, Feng

    2016-05-15

    Lateral flow assays (LFAs) have currently attracted broad interest for point-of-care (POC) diagnostics, but their application has been restricted by poor quantification and limited sensitivity. While the former has been currently solved to some extent by the development of handheld or smartphone-based readers, the latter has not been addressed fully, particularly the potential influences of environmental conditions (e.g., temperature and relative humidity (RH)), which have not yet received serious attention. The present study reports the use of a portable temperature-humidity control device to provide an optimum environmental requirement for sensitivity improvement in LFAs, followed by quantification by using a smartphone. We found that a RH beyond 60% with temperatures of 55-60°C and 37-40°C produced optimum nucleic acid hybridization and antigen-antibody interaction in LFAs, respectively representing a 10-fold and 3-fold signal enhancement over ambient conditions (25°C, 60% RH). We envision that in the future the portable device could be coupled with a fully integrated paper-based sample-to-answer biosensor for sensitive detection of various target analytes in POC settings. Copyright © 2015 Elsevier B.V. All rights reserved.

  8. Microfluidic biosensing device for controlled trapping and detection of magnetic microparticles

    KAUST Repository

    Giouroudi, Ioanna

    2013-05-01

    A magnetic microfluidic device is proposed to transport and trap magnetic microparticles (MPs) to a sensing area. Once the MPs are concentrated in the vicinity of the sensing area, a spin valve type giant magnetoresistance (GMR) sensor is used to detect their presence. The device is used for the detection of biological targets once they are labeled with functionalized MPs. Manipulation of the MPs is achieved by employing a microstructure which consists of planar ringshaped conducting microloops. These microloops are designed to produce high magnetic field gradients which are directly proportional to the force applied to manipulate the MPs. Upon sequential application of current, starting from the outermost loop, MPs are directed to move from the outermost to the innermost loop. The speed with which the MPs move towards the sensing area is controlled by the speed with which current is switched between the loops. On top of the microstructure, a microfluidic channel is fabricated using a standard photolithography technique and a dry film resist layer (Ordyl SY355). Experimental results showed that MPs of different diameters were successfully trapped at the sensing area and detected by the GMR sensor located directly under the innermost square loop. © 2013 IEEE.

  9. Respiratory and Cardiovascular Response during Electronic Control Device Exposure in Law Enforcement Trainees

    Science.gov (United States)

    VanMeenen, Kirsten M.; Lavietes, Marc H.; Cherniack, Neil S.; Bergen, Michael T.; Teichman, Ronald; Servatius, Richard J.

    2013-01-01

    Objective: Law enforcement represents a large population of workers who may be exposed to electronic control devices (ECDs). Little is known about the potential effect of exposure to these devices on respiration or cardiovascular response during current discharge. Methods: Participants (N = 23) were trainees exposed to 5 s of an ECD (Taser X26®) as a component of training. Trainees were asked to volitionally inhale during exposure. Respiratory recordings involved a continuous waveform recorded throughout the session including during the exposure period. Heart rate was calculated from a continuous pulse oximetry recording. Results: The exposure period resulted in the cessation of normal breathing patterns in all participants and in particular a decrease in inspiratory activity. No significant changes in heart rate during ECD exposure were found. Conclusion: This is the first study to examine breathing patterns during ECD exposure with the resolution to detect changes over this discrete period of time. In contrast to reports suggesting respiration is unaffected by ECDs, present evidence suggests that voluntary inspiration is severely compromised. There is no evidence of cardiac disruption during ECD exposure. PMID:23616772

  10. Respiratory and cardiovascular response during electronic control device (ECD exposure in law enforcement trainees

    Directory of Open Access Journals (Sweden)

    Kirsten M. VanMeenen

    2013-04-01

    Full Text Available Objective: Law enforcement represents a large population of workers who may be exposed to electronic control devices (ECDs. Little is known about the potential effect of exposure to these devices on respiration or cardiovascular response during current discharge. Methods: Participants (N=23 were trainees exposed to 5 seconds of an ECD (Taser X26® as a component of training. Trainees were asked to volitionally inhale during exposure. Respiratory recordings involved a continuous waveform recorded throughout the session including during the exposure period. Heart rate was calculated from a continuous pulse oximetry recording. Results: The exposure period resulted in the cessation of normal breathing patterns in all participants and in particular a decrease in inspiratory activity. No significant changes in heart rate during ECD exposure were found. Conclusions: This is the first study to examine breathing patterns during ECD exposure with the resolution to detect changes over this discrete period of time. In contrast to reports suggesting respiration is unaffected by ECDs, present evidence suggests that voluntary inspiration is severely compromised. There is no evidence of cardiac disruption during ECD exposure.

  11. Improvement in Device Performance and Reliability of Organic Light-Emitting Diodes through Deposition Rate Control

    Directory of Open Access Journals (Sweden)

    Shun-Wei Liu

    2014-01-01

    Full Text Available We demonstrated a fabrication technique to reduce the driving voltage, increase the current efficiency, and extend the operating lifetime of an organic light-emitting diode (OLED by simply controlling the deposition rate of bis(10-hydroxybenzo[h]qinolinato beryllium (Bebq2 used as the emitting layer and the electron-transport layer. In our optimized device, 55 nm of Bebq2 was first deposited at a faster deposition rate of 1.3 nm/s, followed by the deposition of a thin Bebq2 (5 nm layer at a slower rate of 0.03 nm/s. The Bebq2 layer with the faster deposition rate exhibited higher photoluminescence efficiency and was suitable for use in light emission. The thin Bebq2 layer with the slower deposition rate was used to modify the interface between the Bebq2 and cathode and hence improve the injection efficiency and lower the driving voltage. The operating lifetime of such a two-step deposition OLED was 1.92 and 4.6 times longer than that of devices with a single deposition rate, that is, 1.3 and 0.03 nm/s cases, respectively.

  12. Standardising visual control devices for tsetse flies: Central and West African species Glossina palpalis palpalis.

    Directory of Open Access Journals (Sweden)

    Dramane Kaba

    Full Text Available BACKGROUND: Glossina palpalis palpalis (G. p. palpalis is one of the principal vectors of sleeping sickness and nagana in Africa with a geographical range stretching from Liberia in West Africa to Angola in Central Africa. It inhabits tropical rain forest but has also adapted to urban settlements. We set out to standardize a long-lasting, practical and cost-effective visually attractive device that would induce the strongest landing response by G. p. palpalis for future use as an insecticide-impregnated tool in area-wide population suppression of this fly across its range. METHODOLOGY/PRINCIPAL FINDINGS: Trials were conducted in wet and dry seasons in the Ivory Coast, Cameroon, the Democratic Republic of Congo and Angola to measure the performance of traps (biconical, monoconical and pyramidal and targets of different sizes and colours, with and without chemical baits, at different population densities and under different environmental conditions. Adhesive film was used as a practical enumerator at these remote locations to compare landing efficiencies of devices. Independent of season and country, both phthalogen blue-black and blue-black-blue 1 m(2 targets covered with adhesive film proved to be as good as traps in phthalogen blue or turquoise blue for capturing G. p. palpalis. Trap efficiency varied (8-51%. There was no difference between the performance of blue-black and blue-black-blue 1 m(2 targets. Baiting with chemicals augmented the overall performance of targets relative to traps. Landings on smaller phthalogen blue-black 0.25 m(2 square targets were not significantly different from either 1 m(2 blue-black-blue or blue-black square targets. Three times more flies were captured per unit area on the smaller device. CONCLUSIONS/SIGNIFICANCE: Blue-black 0.25 m(2 cloth targets show promise as simple cost effective devices for management of G. p. palpalis as they can be used for both control when impregnated with insecticide and for

  13. Quality control of lightweight aggregate concrete based on initial and final water absorption tests

    Science.gov (United States)

    Maghfouri, M.; Shafigh, P.; Ibrahim, Z. Binti; Alimohammadi, V.

    2017-06-01

    Water absorption test is used to evaluate overall performance of concrete in terms of durability. The water absorption of lightweight concrete might be considerably higher than the conventional concrete due to higher rate of pores in concrete and lightweight aggregate. Oil palm shell is a bio-solid waste in palm oil industry, which could be used as lightweight aggregate in the concrete mixture. The present study aims to measure the initial and final water absorption and compressive strength of oil palm shell lightweight concrete in order to evaluation of quality control and durability performance. Total normal coarse aggregates were substituted with coarse oil palm shell in a high strength concrete mixture. The quality of concrete was then evaluated based on the compressive strength and water absorption rates. The results showed that fully substitution of normal coarse aggregates with oil palm shell significantly reduced the compressive strength. However, this concrete with the 28-day compressive strength of 40 MPa still can be used as structural concrete. The initial and final water absorption test results also showed that this concrete is not considered as a good concrete in terms of durability. Therefore, it is recommended that both compressive strength and waster absorption tests must be performed for quality control of oil palm shell concretes.

  14. A test pattern for quality control of laser scanner and charge-coupled device film digitizers.

    Science.gov (United States)

    Halpern, E J

    1995-02-01

    Although clinical images provide the ultimate test of diagnostic performance for a film digitizer, such images are not generally suitable for daily quality control (QC) purposes. However, a well-designed test pattern will provide a rapid, comprehensive, objective and reproducible assessment of image quality. This pattern should evaluate various parameters of image quality, including high contrast resolution, low contrast discrimination, linearity of gray scale, geometric distortion, and noise. Furthermore, the pattern should detect light leak and film slippage, two problems commonly associated with film digitizers. The test pattern described in this manuscript was designed to provide quantitative measures of performance for a film digitizer. As part of a regular QC routine for a laser scanner or charge-coupled device digitizer, this pattern provides a simple method to identify and quantify changes in digital image quality.

  15. Electro-Active Device Using Radial Electric Field Piezo-Diaphragm for Control of Fluid Movement

    Science.gov (United States)

    Bryant, Robert G. (Inventor); Working, Dennis C. (Inventor)

    2005-01-01

    A fluid-control electro-active device includes a piezo-diaphragm made from a ferroelectric material sandwiched by first and second electrode patterns configured to introduce an electric field into the ferroelectric material when voltage is applied thereto. The electric field originates at a region of the ferroelectric material between the first and second electrode patterns, and extends radially outward from this region of the ferroelectric material and substantially parallel to the plane of the ferroelectric material. The piezo-diaphragm deflects symmetrically about this region in a direction substantially perpendicular to the electric field. An annular region coupled to and extending radially outward from the piezo-diaphragm perimetrically borders the piezo-diaphragm, A housing is connected to the region and at least one fluid flow path with piezo-diaphragm disposed therein.

  16. Sudden cardiac arrest and death following application of shocks from a TASER electronic control device.

    Science.gov (United States)

    Zipes, Douglas P

    2012-05-22

    The safety of electronic control devices (ECDs) has been questioned. The goal of this study was to analyze in detail cases of loss of consciousness associated with ECD deployment. Eight cases of TASER X26 ECD-induced loss of consciousness were studied. In each instance, when available, police, medical, and emergency response records, ECD dataport interrogation, automated external defibrillator information, ECG strips, depositions, and autopsy results were analyzed. First recorded rhythms were ventricular tachycardia/fibrillation in 6 cases and asystole (after ≈ 30 minutes of nonresponsiveness) in 1 case. An external defibrillator reported a shockable rhythm in 1 case, but no recording was made. This report offers evidence detailing the mechanism by which an ECD can produce transthoracic stimulation resulting in cardiac electrical capture and ventricular arrhythmias leading to cardiac arrest. ECD stimulation can cause cardiac electrical capture and provoke cardiac arrest resulting from ventricular tachycardia/ventricular fibrillation. After prolonged ventricular tachycardia/ventricular fibrillation without resuscitation, asystole develops.

  17. Integrating a piezoelectric actuator with mechanical and hydraulic devices to control camless engines

    Science.gov (United States)

    Mercorelli, Paolo; Werner, Nils

    2016-10-01

    The paper deals with some interdisciplinary aspects and problems concerning the actuation control which occur in the integration of a piezoelectric structure in an aggregate actuator consisting of a piezoelectric, a stroke ratio displacement, a mechanical and a hydraulic part. Problems like compensation of the piezo hysteresis effect, scaling force-position to obtain an adequate displacement of the actuator and finally the control of such a complex aggregate system are considered and solved. Even though this work considers a particular application, the solutions proposed in the paper are quite general. In fact, the considered technical aspects occurring in systems which utilize piezoelectric technologies can be used in a variegated gamma of actuators integrating piezoelectric technologies. A cascade controller is proposed to combine a Feedforward action with an internal and an external PI-Controller. The Feedforward Controller is based on the model of the whole actuator, so particular attention is paid to the model structure. The resulting Feedforward action is an adaptive one to compensate hydraulic pressure faults. Real measurements are shown.

  18. Cross-flow, filter-sorbent-catalyst for particulate, SO{sub 2} and NO{sub x} control. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Benedek, K. [Little (Arthur D.), Inc., Cambridge, MA (United States); Flytzani-Stephanopoulos, M. [Massachusetts Inst. of Tech., Cambridge, MA (United States)

    1994-05-01

    This report describes work performed on a new concept for integrated pollutant control: An active filter comprised of layered, gas permeable membranes that act as a particle filter, an SO{sub 2} sorbent, and a NO{sub x}, reduction catalyst. The focus of the research program documented in this final report is the development of the sorbent/catalyst materials that are the basis of such an emission control system. The device investigated in this program will simultaneously remove particulates, SO{sub 2} and NO{sub x}, from combustion exhaust gases. Sulfur dioxide capture and nitrogen oxide reduction are achieved with a reg le, mixed-metal oxide sorbent-catalyst. The device is a filter with layered walls: A small-pore layer is a barrier to particles, and a macroporus active layer is a SO{sub 2} sorbent and a catalyst for the selective catalytic reduction of NO{sub x}. The small-pore layer could be an inert ceramic that provides structural strength to the unit and protects the active (sorbent-catalyst) material from abrasion or contamination from fly ash particles. We have found that 95--100% removal efficiency of SO{sub 2} and 60--90% removal of NO{sub x}, is achievable with the use of mixed-metal oxide sorbent-catalysts in the device. The ceramic filters are barriers to particles and typically have removal efficiencies of 99.9%.

  19. High-Efficiency Photovoltaic Devices using Trap-Controlled Quantum-Dot Ink prepared via Phase-Transfer Exchange.

    Science.gov (United States)

    Aqoma, Havid; Al Mubarok, Muhibullah; Hadmojo, Wisnu Tantyo; Lee, Eun-Hye; Kim, Tae-Wook; Ahn, Tae Kyu; Oh, Seung-Hwan; Jang, Sung-Yeon

    2017-05-01

    Colloidal-quantum-dot (CQD) photovoltaic devices are promising candidates for low-cost power sources owing to their low-temperature solution processability and bandgap tunability. A power conversion efficiency (PCE) of >10% is achieved for these devices; however, there are several remaining obstacles to their commercialization, including their high energy loss due to surface trap states and the complexity of the multiple-step CQD-layer-deposition process. Herein, high-efficiency photovoltaic devices prepared with CQD-ink using a phase-transfer-exchange (PTE) method are reported. Using CQD-ink, the fabrication of active layers by single-step coating and the suppression of surface trap states are achieved simultaneously. The CQD-ink photovoltaic devices achieve much higher PCEs (10.15% with a certified PCE of 9.61%) than the control devices (7.85%) owing to improved charge drift and diffusion. Notably, the CQD-ink devices show much lower energy loss than other reported high-efficiency CQD devices. This result reveals that the PTE method is an effective strategy for controlling trap states in CQDs. © 2017 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  20. Squeeze-chip: a finger-controlled microfluidic flow network device and its application to biochemical assays.

    Science.gov (United States)

    Li, Wentao; Chen, Tao; Chen, Zitian; Fei, Peng; Yu, Zhilong; Pang, Yuhong; Huang, Yanyi

    2012-05-07

    We designed and fabricated a novel microfluidic device that can be operated through simple finger squeezing. On-chip microfluidic flow control is enabled through an optimized network of check-valves and squeeze-pumps. The sophisticated flow system can be easily constructed by combining a few key elements. We implemented this device to perform quantitative biochemical assays with no requirement for precision instruments.

  1. A Control Scheme to Improve the Power Quality with the Absence of Dedicated Compensation Devices in Microgrid

    DEFF Research Database (Denmark)

    Naderipour, A.; Mohd Zin, A. A.; Habibuddin, M.H.

    2015-01-01

    devices, such as Active Power Filters (APFs). The proposed control method is composed of the Adjustable Synchronous Reference Frame (ASRF) and the Synchronous Reference Frame (SRF) methods. The ASRF and SRF are proposed to control the power injection and harmonic current compensation, respectively...

  2. 40 CFR 63.497 - Back-end process provisions-monitoring provisions for control and recovery devices.

    Science.gov (United States)

    2010-07-01

    ... Polymers and Resins § 63.497 Back-end process provisions—monitoring provisions for control and recovery... 40 Protection of Environment 9 2010-07-01 2010-07-01 false Back-end process provisions-monitoring provisions for control and recovery devices. 63.497 Section 63.497 Protection of Environment ENVIRONMENTAL...

  3. Using a source-receptor approach to characterize the volatile organic compounds from control device exhaust in a science park.

    Science.gov (United States)

    Chen, Chi-Fan; Liang, Jeng-Jong

    2013-03-01

    The science parks have helped shape Taiwan as a high-tech island with a good reputation worldwide. But some complaints on air pollution from the science parks have recently risen. To better understand the environmental effects of volatile organic compounds (VOCs) emitted from various high-tech factories in a science park, this study uses a source-receptor approach to characterize the environmental effects of VOCs from control device exhaust in Taichung Science Park. The chemical mass balance model (CMB8.2) of field measurements of 30 stacks and ambient air at nine sites was used to identify the source and relative contribution of ambient VOCs. The exhaust gas of various pollution control devices was also sampled by drawing a stream of the gases from the exhaust duct at its sampling port. The VOC source profile of each control device exhaust was determined using a database of noncharacteristic compounds. Monthly ambient concentrations of 167 VOCs were divided into monsoon datasets to investigate the effect of monsoon conditions on the emission of VOCs in the science park. This study also suggests a method for determining the optimum source profile in source-receptor modeling, and identifies and analyzes the sources of ambient VOCs at nine sites during southwest and northeast monsoons. Results show a direct relationship between the relative contribution of each source and its control device efficiency. The proposed source-receptor approach can characterize the environmental effect of air pollutants from various factories and successfully assess the efficiency of various control devices.

  4. Development of a portable quality control application using a tablet-type electronic device.

    Science.gov (United States)

    Ono, Tomohiro; Miyabe, Yuki; Akimoto, Mami; Mukumoto, Nobutaka; Ishihara, Yoshitomo; Nakamura, Mitsuhiro; Mizowaki, Takashi

    2018-02-02

    Our aim was to develop a portable quality control (QC) application using a thermometer, a barometer, an angle gauge, and a range finder implemented in a tablet-type consumer electronic device (CED) and to assess the accuracies of the measurements made. The QC application was programmed using Java and OpenCV libraries. First, temperature and atmospheric pressure were measured over 30 days using the temperature and pressure sensors of the CED and compared with those measured by a double-tube thermometer and a digital barometer. Second, the angle gauge was developed using the accelerometer of the CED. The roll and pitch angles of the CED were measured from 0 to 90° at intervals of 10° in the clockwise (CW) and counterclockwise (CCW) directions. The values were compared with those measured by a digital angle gauge. Third, a range finder was developed using the tablet's built-in camera and image-processing capacities. Surrogate markers were detected by the camera and their positions converted to actual positions using a homographic transformation method. Fiducial markers were placed on a treatment couch and moved 100 mm in 10-mm steps in both the lateral and longitudinal directions. The values were compared with those measured by the digital output of the treatment couch. The differences between CED values and those of other devices were compared by calculating means ± standard deviations (SDs). The means ± SDs of differences in temperature and atmospheric pressure were -0.07 ± 0.25°C and 0.05 ± 0.10 hPa, respectively. The means ± SDs of the difference in angle was -0.17 ± 0.87° (0.15 ± 0.23° degrees excluding the 90° angle). The means ± SDs of distances were 0.01 ± 0.07 mm in both the lateral and longitudinal directions. Our portable QC application was accurate and may be used instead of standard measuring devices. Our portable CED is efficient and simple when used in the field of medical physics. © 2018 American Association of

  5. NOTE: A method for controlling image acquisition in electronic portal imaging devices

    Science.gov (United States)

    Glendinning, A. G.; Hunt, S. G.; Bonnett, D. E.

    2001-02-01

    Certain types of camera-based electronic portal imaging devices (EPIDs) which initiate image acquisition based on sensing a change in video level have been observed to trigger unreliably at the beginning of dynamic multileaf collimation sequences. A simple, novel means of controlling image acquisition with an Elekta linear accelerator (Elekta Oncology Systems, Crawley, UK) is proposed which is based on illumination of a photodetector (ORP-12, Silonex Inc., Plattsburgh, NY, USA) by the electron gun of the accelerator. By incorporating a simple trigger circuit it is possible to derive a beam on/off status signal which changes at least 100 ms before any dose is measured by the accelerator. The status signal does not return to the beam-off state until all dose has been delivered and is suitable for accelerator pulse repetition frequencies of 50-400 Hz. The status signal is thus a reliable means of indicating the initiation and termination of radiation exposure, and thus controlling image acquisition of such EPIDs for this application.

  6. Metal-Controlled Magnetoresistance at Room Temperature in Single-Molecule Devices.

    Science.gov (United States)

    Aragonès, Albert C; Aravena, Daniel; Valverde-Muñoz, Francisco J; Real, José Antonio; Sanz, Fausto; Díez-Pérez, Ismael; Ruiz, Eliseo

    2017-04-26

    The appropriate choice of the transition metal complex and metal surface electronic structure opens the possibility to control the spin of the charge carriers through the resulting hybrid molecule/metal spinterface in a single-molecule electrical contact at room temperature. The single-molecule conductance of a Au/molecule/Ni junction can be switched by flipping the magnetization direction of the ferromagnetic electrode. The requirements of the molecule include not just the presence of unpaired electrons: the electronic configuration of the metal center has to provide occupied or empty orbitals that strongly interact with the junction metal electrodes and that are close in energy to their Fermi levels for one of the electronic spins only. The key ingredient for the metal surface is to provide an efficient spin texture induced by the spin-orbit coupling in the topological surface states that results in an efficient spin-dependent interaction with the orbitals of the molecule. The strong magnetoresistance effect found in this kind of single-molecule wire opens a new approach for the design of room-temperature nanoscale devices based on spin-polarized currents controlled at molecular level.

  7. Neuronal ensemble control of prosthetic devices by a human with tetraplegia

    Science.gov (United States)

    Hochberg, Leigh R.; Serruya, Mijail D.; Friehs, Gerhard M.; Mukand, Jon A.; Saleh, Maryam; Caplan, Abraham H.; Branner, Almut; Chen, David; Penn, Richard D.; Donoghue, John P.

    2006-07-01

    Neuromotor prostheses (NMPs) aim to replace or restore lost motor functions in paralysed humans by routeing movement-related signals from the brain, around damaged parts of the nervous system, to external effectors. To translate preclinical results from intact animals to a clinically useful NMP, movement signals must persist in cortex after spinal cord injury and be engaged by movement intent when sensory inputs and limb movement are long absent. Furthermore, NMPs would require that intention-driven neuronal activity be converted into a control signal that enables useful tasks. Here we show initial results for a tetraplegic human (MN) using a pilot NMP. Neuronal ensemble activity recorded through a 96-microelectrode array implanted in primary motor cortex demonstrated that intended hand motion modulates cortical spiking patterns three years after spinal cord injury. Decoders were created, providing a `neural cursor' with which MN opened simulated e-mail and operated devices such as a television, even while conversing. Furthermore, MN used neural control to open and close a prosthetic hand, and perform rudimentary actions with a multi-jointed robotic arm. These early results suggest that NMPs based upon intracortical neuronal ensemble spiking activity could provide a valuable new neurotechnology to restore independence for humans with paralysis.

  8. Scattering Fields Control by Metamaterial Device Based on Ultra-Broadband Polarization Converters

    Directory of Open Access Journals (Sweden)

    Si-Jia Li

    2016-12-01

    Full Text Available We proposed a novel ultra-broadband meta¬material screen with controlling the electromagnetic scat¬tering fields based on the three layers wideband polariza¬tion converter (TLW-PC. The unit cell of TLW-PC was composed of a three layers substrate loaded with double metallic split-rings structure and a metal ground plane. We observed that the polarization converter primarily per¬formed ultra-broadband cross polarization conversion from 5.71 GHz to 14.91 GHz. Furthermore, a metamaterial screen, which contributed to the low scattering charac¬teristics, had been exploited with the orthogonal array based on TLW-PC. The near scattering electronic fields are controlled due to the change of phase and amplitude for incident wave. The metamaterial screen significantly exhibited low scattering characteristics from 5.81 GHz to 15.06 GHz. To demonstrate design, a metamaterial device easily implemented by the common printed circuit board method has been fabricated and measured. Experimental results agreed well with the simulated results.

  9. Intraocular pressure control of a novel glaucoma drainage device - in vitro and in vivo studies.

    Science.gov (United States)

    Cui, Li-Jun; Li, Di-Chen; Liu, Jian; Zhang, Lei; Xing, Yao

    2017-01-01

    To evaluate the intraocular pressure (IOP) control of an artificial trabeculum drainage system (ATDS), a newly designed glaucoma drainage device, and postoperative complications in normal rabbit eyes. Pressure drops in air and fluid of 30 ATDS were measured after being connected to a closed manometric system. Twenty of them were then chosen and implanted randomly into the eyes of 20 rabbits. Postoperative slit-lamp, gonioscopic examination and IOP measurements were recorded periodically. Ultrasound biomicroscopy and B-scan ultrasonography were also used to observe the complications. Eyes were enucleated on day 60. Pressure drops of 4.6-9.4 mm Hg were obtained at physiological aqueous flow rates in the tests in vitro. The average postoperative IOP of the experimental eyes (11.6-12.8 mm Hg) was lower than the controls significantly (Pdevices were devoid of obstructions in all specimens examined and a thin fibrous capsule was found around the endplate. ATDS reduce IOP effectively. However, further studies on the structure are needed to reduce complications.

  10. A synthetic multifunctional mammalian pH sensor and CO2 transgene-control device.

    Science.gov (United States)

    Ausländer, David; Ausländer, Simon; Charpin-El Hamri, Ghislaine; Sedlmayer, Ferdinand; Müller, Marius; Frey, Olivier; Hierlemann, Andreas; Stelling, Jörg; Fussenegger, Martin

    2014-08-07

    All metabolic activities operate within a narrow pH range that is controlled by the CO2-bicarbonate buffering system. We hypothesized that pH could serve as surrogate signal to monitor and respond to the physiological state. By functionally rewiring the human proton-activated cell-surface receptor TDAG8 to chimeric promoters, we created a synthetic signaling cascade that precisely monitors extracellular pH within the physiological range. The synthetic pH sensor could be adjusted by organic acids as well as gaseous CO2 that shifts the CO2-bicarbonate balance toward hydrogen ions. This enabled the design of gas-programmable logic gates, provided remote control of cellular behavior inside microfluidic devices, and allowed for CO2-triggered production of biopharmaceuticals in standard bioreactors. When implanting cells containing the synthetic pH sensor linked to production of insulin into type 1 diabetic mice developing diabetic ketoacidosis, the prosthetic network automatically scored acidic pH and coordinated an insulin expression response that corrected ketoacidosis. Copyright © 2014 Elsevier Inc. All rights reserved.

  11. Graphene-coated meshes for electroactive flow control devices utilizing two antagonistic functions of repellency and permeability

    Science.gov (United States)

    Tabassian, Rassoul; Oh, Jung-Hwan; Kim, Sooyeun; Kim, Donggyu; Ryu, Seunghwa; Cho, Seung-Min; Koratkar, Nikhil; Oh, Il-Kwon

    2016-10-01

    The wettability of graphene on various substrates has been intensively investigated for practical applications including surgical and medical tools, textiles, water harvesting, self-cleaning, oil spill removal and microfluidic devices. However, most previous studies have been limited to investigating the intrinsic and passive wettability of graphene and graphene hybrid composites. Here, we report the electrowetting of graphene-coated metal meshes for use as electroactive flow control devices, utilizing two antagonistic functions, hydrophobic repellency versus liquid permeability. Graphene coating was able to prevent the thermal oxidation and corrosion problems that plague unprotected metal meshes, while also maintaining its hydrophobicity. The shapes of liquid droplets and the degree of water penetration through the graphene-coated meshes were controlled by electrical stimuli based on the functional control of hydrophobic repellency and liquid permeability. Furthermore, using the graphene-coated metal meshes, we developed two active flow devices demonstrating the dynamic locomotion of water droplets and electroactive flow switching.

  12. A Review on Natural Ventilation-enabling Façade Noise Control Devices for Congested High-Rise Cities

    Directory of Open Access Journals (Sweden)

    Shiu-Keung Tang

    2017-02-01

    Full Text Available This review summarizes the current status of the research and development of natural ventilation-enabling noise control devices for use on the façades of high-rise residential buildings in congested cities. These devices are important for a sustainable urbanized city, as they are supposed to offer good acoustical protection to citizens, allowing for an acceptable level of natural ventilation inside residential units; energy for mechanical ventilation can then be saved. From the information presented in the existing literature, it is concluded that protrusive devices, such as lintels and balconies, are not effective noise screening devices, even if they are installed with sound absorbers and/or reflectors, under the effect of city reverberation. On the contrary, plenum windows and similar structures, which are plenum structures with a staggered air inlet and outlet, are interesting alternatives that are worth rigorous considerations.

  13. Development of size-specific data from particulate control technology research reports. Final report, March-September 1992

    Energy Technology Data Exchange (ETDEWEB)

    Dean, T.A.; Doorn, M.R.J.; Barnard, W.R.; Coleman, R.

    1992-11-01

    The report gives size-specific, uncontrolled emission factors and control efficiencies developed from many studies of particulate control device performance conducted under the direction of EPA's Air and Energy Engineering Research Laboratory (AEERL) between 1974 and 1981. The particle size ranges of concern are 02.5, 2.5-6, 6-10, and 0-10 micrometers. These data and the sampling and analysis procedures documented in the reports were subjected to a quality assurance review and then compared with source- and control-device-specific information in several data sources maintained by EPA's Office of Air Quality Planning and Standards (OAQPS). Where no relevant information existed in these data sources, it was determined that the data developed from these studies should be incorporated into them. Each control device study is reviewed individually. For each study, the source, control device, and sampling configuration are described briefly, the quality of the sampling and analysis methods is rated informally, the data are compared with comparable AP-42 data, and conclusions are drawn regarding the need for the data in the OAQPS data sources. Reviews of documents which yielded data not suitable for inclusion in the OAQPS data sources are also included.

  14. Temperature-controlled electrothermal atomization-atomic absorption spectrometry using a pyrometric feedback system in conjunction with a background monitoring device

    Science.gov (United States)

    Van Deijck, W.; Roelofsen, A. M.; Pieters, H. J.; Herber, R. F. M.

    The construction of a temperature-controlled feedback system for electrothermal atomization-atomic absorption spectrometry (ETA-AAS) using an optical pyrometer applied to the atomization stage is described. The system was used in conjunction with a fast-response background monitoring device. The heating rate of the furnace amounted to 1400° s -1 with a reproducibility better than 1%. The precision of the temperature control at a steady state temperature of 2000°C was 0.1%. The analytical improvements offered by the present system have been demonstrated by the determination of cadmium and lead in blood and finally by the determination of lead in serum. Both the sensitivity and the precision of the method have been improved. The accuracy of the method was checked by determining the lead content for a number of scrum samples both by ETA-AAS and differential pulse anodic stripping voltametry (DPASV) and proved to be satisfactory.

  15. Impact of the Shodan Computer Search Engine on Internet-facing Industrial Control System Devices

    Science.gov (United States)

    2014-03-27

    Table 2.1) [43]. In addition to an Internet-facing device 19 index, Shodan offers an exploit database, a raw nmap data output visualization tool, and...Automation 1769-L23E-QB1 PLC based on NMAP’s device fingerprinting service. Note the scan for all four honeypots yielded the same results. NMAP device... fingerprinting is based on a comparison of device responses to specific TCP/IP probes and open TCP or UDP ports. An investigation into the NMAP

  16. Metal nanoparticle mediated space charge and its optical control in an organic hole-only device

    Energy Technology Data Exchange (ETDEWEB)

    Ligorio, G.; Nardi, M. V. [Institut für Physik & IRIS Adlershof, Humboldt-Universität zu Berlin, Brook-Taylor Str. 6, 12489 Berlin (Germany); Steyrleuthner, R.; Neher, D. [Institute of Physics and Astronomy, Universität Potsdam, Karl-Liebknecht Str. 24, 14476 Potsdam (Germany); Ihiawakrim, D. [Institut de Physique et de Chimie des Matériaux de Strasbourg, Université de Strasbourg, CNRS UMR 7504, 23 rue du Loess, BP 43, 67034 Strasbourg, Cedex2 (France); Crespo-Monteiro, N.; Brinkmann, M. [Institut Charles Sadron CNRS, 23 rue du Loess, 67034 Strasbourg (France); Koch, N., E-mail: norbert.koch@physik.hu-berlin.de [Institut für Physik & IRIS Adlershof, Humboldt-Universität zu Berlin, Brook-Taylor Str. 6, 12489 Berlin (Germany); Helmholtz-Zentrum Berlin für Materialien und Energie GmbH, Erneuerbare Energien, Albert-Einstein Str. 15, 12489 Berlin (Germany)

    2016-04-11

    We reveal the role of localized space charges in hole-only devices based on an organic semiconductor with embedded metal nanoparticles (MNPs). MNPs act as deep traps for holes and reduce the current density compared to a device without MNPs by a factor of 10{sup 4} due to the build-up of localized space charge. Dynamic MNPs charged neutrality can be realized during operation by electron transfer from excitons created in the organic matrix, enabling light sensing independent of device bias. In contrast to the previous speculations, electrical bistability in such devices was not observed.

  17. Tailoring strain in microelectronic devices

    NARCIS (Netherlands)

    van Hemert, T.

    2013-01-01

    The central device of this thesis is the transistor. It acts like a faucet, but hen for electric charge. There is a connection that is called the source, just like the water company. And the charge flows into the drain. Finally there is a handle, here called the gate, to control the flow of charge.

  18. Energy consumption analysis of graphene based all spin logic device with voltage controlled magnetic anisotropy

    Directory of Open Access Journals (Sweden)

    Zhizhong Zhang

    2017-05-01

    Full Text Available All spin logic device (ASLD is a promising option to realize the ultra-low power computing systems. However, the low spin transport efficiency and the non-local switching of the detector have become two key challenges of the ASLD. In this paper, we analyze the energy consumption of a graphene based ASLD with the ferromagnetic layer switching assistance by voltage control magnetic anisotropy (VCMA effect. This structure has significant potential towards ultra-low power consumption: the applied voltage can not only shorten switching time of the ferromagnetic layer, but also decreases the critical injection current; the graphene channel enhances greatly the spin transport efficiency. By applying the approximate circuit model, the impact of material configurations, interfaces and geometry can be synthetically studied. An accurate physic model was also developed, based on which, we carry out the micro-magnetic simulations to analyze the magnetization dynamics. Combining these electrical and magnetic investigations, the energy consumption of the proposed ASLD can be estimated. With the optimizing parameters, the energy consumption can be reduced to 2.5 pJ for a logic operation.

  19. Combined-hole film cooling with the application of double flow control devices

    Directory of Open Access Journals (Sweden)

    Hassan Haswira

    2017-01-01

    Full Text Available In the modern gas turbine, film cooling system was applied to the turbine blades to provide thermal protection from extreme turbine inlet temperatures. Recent literature discovers that adding the double flow control device (DFCD and combining two cylindrical holes (combinedhole are the ways to further enhance the film cooling performances. In the present simulation work, the influence of DFCD on the combined-hole film cooling was investigated at different blowing ratios. The comparison between two different computational domains of combined-hole film cooling with and without DFCD was further discussed in the present work. The results show that increase the blowing ratio, M rise the overall performance of combined-hole film cooling with and without DFCD. Based on the different computational domain, combined-hole with DFCD has better lateral spread at M = 0.5 and M = 0.75 in comparison with the combined-hole without DFCD. However, due to large counter clockwise vortex produced by the combined-hole with DFCD, unsymmetrical film cooling coverage was formed along the streamwise direction at M = 1.0 and M =1.5. As the conclusion, combined-hole film cooling with DFCD has better performance at M = 0.5 and M = 0.75 while combined-hole film cooling without DFCD has better performance at high blowing ratio of M = 1.0 and M = 1.5.

  20. The Assessment of Postural Control, Reflex Integration, and Bilateral Motor Coordination of Young Handicapped Children. Final Report.

    Science.gov (United States)

    DeGangi, Georgia; Larsen, Lawrence A.

    A measurement device, Assessment of Sensorimotor Integration in Preschool Children, was developed to assess postural control, reflex integration and bilateral motor integration in developmentally delayed children (3 to 5 years old). The test was administered to 113 normal children and results were compared with data collected on 23 developmentally…

  1. Enhancements to a Superconducting Quantum Interference Device (SQUID) Multiplexer Readout and Control System

    Science.gov (United States)

    Forgione, J.; Benford, D. J.; Buchanan, E. D.; Moseley, S. H.; Rebar, J.; Shafer, R. A.

    2004-01-01

    Far-infrared detector arrays such as the 16x32 superconducting bolometer array for the SAFIRE instrument (flying on the SOFIA airborne observatory) require systems of readout and control electronics to provide translation between a user-driven, digital PC and the cold, analog world of the cryogenic detector. In 2001, the National Institute of Standards and Technology (NIST) developed their Mark III electronics for purposes of control and readout of their 1x32 SQUID Multiplexer chips. We at NASA s Goddard Space Flight Center acquired a Mark 111 system and subsequently designed upgrades to suit our and our collaborators purposes. We developed an arbitrary, programmable multiplexing system that allows the user to cycle through rows in a SQUID array in an infinite number of combinations. We provided hooks in the Mark III system to allow readout of signals from outside the Mark 111 system, such as telescope status information. Finally, we augmented the heart of the system with a new feedback algorithm implementation, flexible diagnostic tools, and informative telemetry.

  2. Evaluation of mercury speciation and removal through air pollution control devices of a 190 MW boiler.

    Science.gov (United States)

    Wu, Chengli; Cao, Yan; Dong, Zhongbing; Cheng, Chinmin; Li, Hanxu; Pan, Weiping

    2010-01-01

    Air pollution control devices (APCDs) are installed at coal-fired power plants for air pollutant regulation. Selective catalytic reduction (SCR) and wet flue gas desulfurization (FGD) systems have the co-benefits of air pollutant and mercury removal. Configuration and operational conditions of APCDs and mercury speciation affect mercury removal efficiently at coal-fired utilities. The Ontario Hydro Method (OHM) recommended by the U.S. Environmental Protection Agency (EPA) was used to determine mercury speciation simultaneously at five sampling locations through SCR-ESP-FGD at a 190 MW unit. Chlorine in coal had been suggested as a factor affecting the mercury speciation in flue gas; and low-chlorine coal was purported to produce less oxidized mercury (Hg2+) and more elemental mercury (Hg0) at the SCR inlet compared to higher chlorine coal. SCR could oxidize elemental mercury into oxidized mercury when SCR was in service, and oxidation efficiency reached 71.0%. Therefore, oxidized mercury removal efficiency was enhanced through a wet FGD system. In the non-ozone season, about 89.5%-96.8% of oxidized mercury was controlled, but only 54.9%-68.8% of the total mercury was captured through wet FGD. Oxidized mercury removal efficiency was 95.9%-98.0%, and there was a big difference in the total mercury removal efficiencies from 78.0% to 90.2% in the ozone season. Mercury mass balance was evaluated to validate reliability of OHM testing data, and the ratio of mercury input in the coal to mercury output at the stack was from 0.84 to 1.08.

  3. Intrauterine device use and risk of tubal pregnancy: an Indonesian case-control study.

    Science.gov (United States)

    Basuki, B; Rossing, M A; Daling, J R

    1994-10-01

    We assessed the risk of tubal pregnancy among women who (1) were currently using an intrauterine device (IUD) and (2) had discontinued IUD use while still sexually active and at risk of pregnancy using data from a multicentre case-control study of married women conducted in Indonesia. Cases were 560 women diagnosed with histologically confirmed ectopic pregnancy from April 1989 to August 1990 at any one of 11 participating hospitals. Controls were 1120 non-pregnant women similar in age and place of residence to the cases. In-person interviews were conducted to collect information regarding current and past contraceptive use as well as other demographic and personal characteristics. Women currently using an IUD were considerably less likely than women not currently using contraception, but more likely than users of hormonal or surgical means of contraception, to develop a tubal pregnancy. Women who had discontinued using an IUD had a 70% subsequent increase in risk of tubal pregnancy (adjusted RR = 1.7, 95% Cl: 1.1-2.5) relative to women who had never used an IUD. This increase in risk was most pronounced in women who reported multiple episodes of IUD use and, to a lesser extent, in women with a long (> 3 year) duration of IUD use. The associations we observed are similar to those previously reported in studies conducted in developed countries. The results are of particular interest because this study was conducted in a location in which the Dalkon Shield IUD was never available, and among a population of married, gravid women for whom IUD use is generally considered most appropriate.

  4. National Renewable Energy Laboratory (NREL) Topic 2 Final Report: End-to-End Communication and Control System to Support Clean Energy Technologies

    Energy Technology Data Exchange (ETDEWEB)

    Hudgins, Andrew P [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Carrillo, Ismael M [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Jin, Xin [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Simmins, John [Electric Power Research Institute (EPRI)

    2018-02-21

    This document is the final report of a two-year development, test, and demonstration project, 'Cohesive Application of Standards- Based Connected Devices to Enable Clean Energy Technologies.' The project was part of the National Renewable Energy Laboratory's (NREL's) Integrated Network Testbed for Energy Grid Research and Technology (INTEGRATE) initiative hosted at Energy Systems Integration Facility (ESIF). This project demonstrated techniques to control distribution grid events using the coordination of traditional distribution grid devices and high-penetration renewable resources and demand response. Using standard communication protocols and semantic standards, the project examined the use cases of high/low distribution voltage, requests for volt-ampere-reactive (VAR) power support, and transactive energy strategies using Volttron. Open source software, written by EPRI to control distributed energy resources (DER) and demand response (DR), was used by an advanced distribution management system (ADMS) to abstract the resources reporting to a collection of capabilities rather than needing to know specific resource types. This architecture allows for scaling both horizontally and vertically. Several new technologies were developed and tested. Messages from the ADMS based on the common information model (CIM) were developed to control the DER and DR management systems. The OpenADR standard was used to help manage grid events by turning loads off and on. Volttron technology was used to simulate a homeowner choosing the price at which to enter the demand response market. Finally, the ADMS used newly developed algorithms to coordinate these resources with a capacitor bank and voltage regulator to respond to grid events.

  5. Controlling system for smart hyper-spectral imaging array based on liquid-crystal Fabry-Perot device

    Science.gov (United States)

    Jiang, Xue; Chen, Xin; Rong, Xin; Liu, Kan; Zhang, Xinyu; Ji, An; Xie, Changsheng

    2011-11-01

    A research for developing a kind of smart spectral imaging detection technique based on the electrically tunable liquidcrystal (LC) FP structure is launched. It has some advantages of low cost, highly compact integration, perfuming wavelength selection without moving any micro-mirror of FP device, and the higher reliability and stability. The controlling system for hyper-spectral imaging array based on LC-FP device includes mainly a MSP430F5438 as its core. Considering the characteristics of LC-FP device, the controlling system can provide a driving signal of 1-10 kHz and 0- 30Vrms for the device in a static driving mode. This paper introduces the hardware designing of the control system in detail. It presents an overall hardware solutions including: (1) the MSP430 controlling circuit, and (2) the operational amplifier circuit, and (3) the power supply circuit, and (4) the AD conversion circuit. The techniques for the realization of special high speed digital circuits, which is necessary for the PCB employed, is also discussed.

  6. Development of a thermodynamic control system for the Fontan circulation pulsation device using shape memory alloy fibers.

    Science.gov (United States)

    Yamada, Akihiro; Shiraishi, Yasuyuki; Miura, Hidekazu; Hashem, Hashem Mohamed Omran; Tsuboko, Yusuke; Yamagishi, Masaaki; Yambe, Tomoyuki

    2015-09-01

    The Fontan procedure is one of the common surgical treatments for circulatory reconstruction in pediatric patients with congenital heart disease. In Fontan circulation, low pulsatility may induce localized lung ischemia and may impair the development of pulmonary peripheral endothelial cells. To promote pulmonary circulation in Fontan circulation, we have been developing a pediatric pulmonary circulatory pulsation device using shape memory alloy fibers attached from the outside of total cavopulmonary connection. In this study, we developed a new thermal control system for the device and examined its functions. We mounted on the device 16 fibers connected in parallel around an ePTFE graft circumferentially. To provide optimized contraction, we designed the new thermal control system. The system consisted of a thermistor, a pressure sensor, and a regulator that was controlled by the adaptive thermodynamic transfer functions. We monitored the parameters and calculated heat transfer function as well as pressure distribution on the graft surface. Then we examined and compared the dynamic contractile pressure and changes in surface temperature. As a result, by the application of the control based on the new feedback system analysis, the circumferential contractile pressure increased by 35%. The adaptive thermodynamic regulation was useful for the selection of alternative thresholds of the surface temperature of the graft. The system could achieve effective contraction for the pulsatile flow generation by the device.

  7. 40 CFR Table 1 to Subpart IIIi of... - Operating Limits for Capture Systems and Add-On Control Devices

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 12 2010-07-01 2010-07-01 true Operating Limits for Capture Systems... 63—Operating Limits for Capture Systems and Add-On Control Devices If you are required to comply with operating limits by § 63.3093, you must comply with the applicable operating limits in the following table...

  8. In vitro development of donated frozen-thawed human embryos in a prototype static microfluidic device: a randomized controlled trial

    NARCIS (Netherlands)

    Kieslinger, Dorit C.; Hao, Zhenxia; Vergouw, Carlijn G.; Kostelijk, Elisabeth H.; Lambalk, Cornelis B.; le Gac, Severine

    Objective: To compare the development of human embryos in microfluidic devices with culture in standard microdrop dishes, both under static conditions. Design: Prospective randomized controlled trial. Setting: In vitro fertilization laboratory. Patient(s): One hundred eighteen donated frozen-thawed

  9. Final focus nomenclature

    Energy Technology Data Exchange (ETDEWEB)

    Erickson, R.

    1986-08-08

    The formal names and common names for all devices in the final focus system of the SLC are listed. The formal names consist of a device type designator, microprocessor designator, and a four-digit unit number. (LEW)

  10. Dynamic characterization and modelling of a dual-axis beam steering device for performance understanding, optimization and control design

    Science.gov (United States)

    Berglund, Martin; Palmer, Kristoffer; Lotfi, Sara; Kratz, Henrik; Thornell, Greger

    2013-04-01

    This paper presents a lumped thermal model of a dual-axis laser micromirror device for beam steering in a free-space optical (FSO) communication system, designed for fractionated spacecraft. An FSO communication system provides several advantages, such as larger bandwidth, smaller size and weight of the communication payload and less power consumption. A dual-axis mirror device is designed and realized using microelectromechanical systems technology. The fabrication is based on a double-sided, bulk micromachining process, where the mirror actuates thermally by joints consisting of v-grooves filled with the SU-8 polymer. The size of the device, consisting of a mirror, which is deflectable versus its frame in one direction, and through deflection of the frame in the other, is 15.4 × 10.4 × 0.3 mm3. In order to further characterize and understand the micromirror device, a Simulink state-space model of the actuator is set up using thermal and mechanical properties from a realized actuator. A deviation of less than 2% between the modelled and measured devices was obtained in an actuating temperature range of 20-200 °C. The model of the physical device was examined by evaluating its performance in vacuum, and by changing physical parameters, such as thickness and material composition. By this, design parameters were evaluated for performance gain and usability. For example, the crosstalk between the two actuators deflecting the mirror along its two axes in atmospheric pressure is projected to go down from 97% to 6% when changing the frame material from silicon to silicon dioxide. A feedback control system was also designed around the model in order to examine the possibility to make a robust control system for the physical device. In conclusion, the model of the actuator presented in this paper can be used for further understanding and development of the actuator system.

  11. Effect Of Steel Flow Control Devices On Flow And Temperature Field In The Tundish Of Continuous Casting Machine

    Directory of Open Access Journals (Sweden)

    Sowa L.

    2015-06-01

    Full Text Available The mathematical model and numerical simulations of the liquid steel flow in a tundish are presented in this paper. The problem was treated as a complex and solved by the finite element method. One takes into consideration in the mathematical model the changes of thermophysical parameters depending on the temperature. The single-strand tundish is used to casting slabs. The internal work space of the tundish was modified by flow control devices. The first device was a pour pad situated in the pouring tundish zone. The second device was a dam. The third device was a baffle with three holes. The dam and baffle were placed in the tundish at different positions depending on the variant. The main purpose of using these was to put barriers in the steel flow path as well as give directional metal flow upwards which facilitated inclusion floatation. The interaction of flow control devices on hydrodynamic conditions was received from numerical simulations. As a result of the computations carried out, the liquid steel flow and steel temperature fields were obtained. The influences of the tundish modifications on the velocity fields in liquid phase of the steel were estimated, because these have essential an influence on high-quality of a continuous steel cast slab.

  12. 40 CFR 63.1015 - Closed vent systems and control devices; or emissions routed to a fuel gas system or process.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 10 2010-07-01 2010-07-01 false Closed vent systems and control devices; or emissions routed to a fuel gas system or process. 63.1015 Section 63.1015 Protection of... Equipment Leaks-Control Level 1 § 63.1015 Closed vent systems and control devices; or emissions routed to a...

  13. 40 CFR 63.1034 - Closed vent systems and control devices; or emissions routed to a fuel gas system or process...

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 10 2010-07-01 2010-07-01 false Closed vent systems and control devices; or emissions routed to a fuel gas system or process standards. 63.1034 Section 63.1034 Protection... Equipment Leaks-Control Level 2 Standards § 63.1034 Closed vent systems and control devices; or emissions...

  14. 40 CFR 63.4167 - How do I establish the emission capture system and add-on control device operating limits during...

    Science.gov (United States)

    2010-07-01

    ... system and add-on control device operating limits during the performance test? 63.4167 Section 63.4167... with Add-on Controls Option § 63.4167 How do I establish the emission capture system and add-on control device operating limits during the performance test? During the performance test required by § 63.4160...

  15. 40 CFR 63.4767 - How do I establish the emission capture system and add-on control device operating limits during...

    Science.gov (United States)

    2010-07-01

    ... system and add-on control device operating limits during the performance test? 63.4767 Section 63.4767... Rate with Add-on Controls Option § 63.4767 How do I establish the emission capture system and add-on control device operating limits during the performance test? During the performance test required by § 63...

  16. 40 CFR 63.3167 - How do I establish the add-on control device operating limits during the performance test?

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 12 2010-07-01 2010-07-01 true How do I establish the add-on control... Limitations § 63.3167 How do I establish the add-on control device operating limits during the performance.... (a) Thermal oxidizers. If your add-on control device is a thermal oxidizer, establish the operating...

  17. 40 CFR 63.4363 - How do I establish the add-on control device operating limits during the performance test?

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 12 2010-07-01 2010-07-01 true How do I establish the add-on control... § 63.4363 How do I establish the add-on control device operating limits during the performance test... specified in § 63.4292. (a) Thermal oxidizers. If your add-on control device is a thermal oxidizer...

  18. The Reality of Myoelectric Prostheses: Understanding What Makes These Devices Difficult for Some Users to Control.

    Science.gov (United States)

    Chadwell, Alix; Kenney, Laurence; Thies, Sibylle; Galpin, Adam; Head, John

    2016-01-01

    Users of myoelectric prostheses can often find them difficult to control. This can lead to passive-use of the device or total rejection, which can have detrimental effects on the contralateral limb due to overuse. Current clinically available prostheses are "open loop" systems, and although considerable effort has been focused on developing biofeedback to "close the loop," there is evidence from laboratory-based studies that other factors, notably improving predictability of response, may be as, if not more, important. Interestingly, despite a large volume of research aimed at improving myoelectric prostheses, it is not currently known which aspect of clinically available systems has the greatest impact on overall functionality and everyday usage. A protocol has, therefore, been designed to assess electromyographic (EMG) skill of the user and predictability of the prosthesis response as significant parts of the control chain, and to relate these to functionality and everyday usage. Here, we present the protocol and results from early pilot work. A set of experiments has been developed. First, to characterize user skill in generating the required level of EMG signal, as well as the speed with which users are able to make the decision to activate the appropriate muscles. Second, to measure unpredictability introduced at the skin-electrode interface, in order to understand the effects of the socket-mounted electrode fit under different loads on the variability of time taken for the prosthetic hand to respond. To evaluate prosthesis user functionality, four different outcome measures are assessed. Using a simple upper limb functional task prosthesis users are assessed for (1) success of task completion, (2) task duration, (3) quality of movement, and (4) gaze behavior. To evaluate everyday usage away from the clinic, the symmetricity of their real-world arm use is assessed using activity monitoring. These methods will later be used to assess a prosthesis user cohort to

  19. The reality of myoelectric prostheses: Understanding what makes these devices difficult for some users to control

    Directory of Open Access Journals (Sweden)

    Alix Chadwell

    2016-08-01

    Full Text Available Users of myoelectric prostheses can often find them difficult to control. This can lead to passive-use of the device or total rejection, which can have detrimental effects on the contralateral limb due to overuse.Current clinically available prostheses are ‘open loop’ systems, and although considerable effort has been focused on developing biofeedback to close the loop, there is evidence from laboratory-based studies that other factors, notably improving predictability of response, may be as, if not more, important. Interestingly, despite a large volume of research aimed at improving myoelectric prostheses, it is not currently known which aspect of clinically available systems has the greatest impact on overall functionality and everyday usage. A protocol has therefore been designed to assess EMG skill of the user and predictability of the prosthesis response as significant parts of the control chain, and to relate these to functionality and everyday usage. Here we present the protocol and results from early pilot work.A set of experiments has been developed. Firstly to characterize user skill in generating the required level of EMG signal, as well as the speed with which users are able to make the decision to activate the appropriate muscles. Secondly, to measure unpredictability introduced at the skin-electrode interface, in order to understand the effects of the socket mounted electrode fit under different loads on the variability of time taken for the prosthetic hand to respond.To evaluate prosthesis user functionality, four different outcome measures are assessed. Using a simple upper limb functional task prosthesis users are assessed for (1 success of task completion, (2 task duration, (3 quality of movement, and (4 gaze behavior. To evaluate everyday usage away from the clinic, the symmetricity of their real-world arm use is assessed using activity monitoring.These methods will later be used to assess a prosthesis user cohort, to

  20. Advanced in-duct sorbent injection for SO{sub 2} control. Final technical report

    Energy Technology Data Exchange (ETDEWEB)

    Stouffer, M.R.; Withium, J.A.; Rosenhoover, W.A.; Maskew, J.T.

    1994-12-01

    The objective of this research project was to develop a second generation duct sorbent injection technology as a cost-effective compliance option for the 1990 Clean Air Act Amendments. Research and development work was focused on the Advanced Coolside process, which showed the potential for exceeding the original performance targets of 90% SO{sub 2} removal and 60% sorbent utilization. Process development was conducted in a 1000 acfm pilot plant. The pilot plant testing showed that the Advanced Coolside process can achieve 90% SO{sub 2} removal at sorbent utilizations up to 75%. The testing also showed that the process has the potential to achieve very high removal efficiency (90 to >99%). By conducting conceptual process design and economic evaluations periodically during the project, development work was focused on process design improvements which substantially lowered process capital and operating costs, A final process economic study projects capital costs less than one half of those for limestone forced oxidation wet FGD. Projected total SO{sub 2} control cost is about 25% lower than wet FGD for a 260 MWe plant burning a 2.5% sulfur coal. A waste management study showed the acceptability of landfill disposal; it also identified a potential avenue for by-product utilization which should be further investigated. Based on the pilot plant performance and on the above economic projections, future work to scale up the Advanced Coolside process is recommended.

  1. Minimization of temperature ranges between the top and bottom of an air flow controlling device through hybrid control in a plant factory.

    Science.gov (United States)

    Moon, Seung-Mi; Kwon, Sook-Youn; Lim, Jae-Hyun

    2014-01-01

    To maintain the production timing, productivity, and product quality of plant factories, it is necessary to keep the growth environment uniform. A vertical multistage type of plant factory involves different levels of growing trays, which results in the problem of difference in temperature among vertically different locations. To address it, it is necessary to install air flow devices such as air flow fan and cooling/heating device at the proper locations in order to facilitate air circulation in the facility as well as develop a controlling technology for efficient operation. Accordingly, this study compares the temperature and air distribution within the space of a vertical multistage closed-type plant factory by controlling cooling/heating devices and air flow fans harmoniously by means of the specially designed testbed. The experiment results indicate that in the hybrid control of cooling and heating devices and air flow fans, the difference in temperature decreased by as much as 78.9% compared to that when only cooling and heating devices were operated; the air distribution was improved by as much as 63.4%.

  2. Minimization of Temperature Ranges between the Top and Bottom of an Air Flow Controlling Device through Hybrid Control in a Plant Factory

    Directory of Open Access Journals (Sweden)

    Seung-Mi Moon

    2014-01-01

    Full Text Available To maintain the production timing, productivity, and product quality of plant factories, it is necessary to keep the growth environment uniform. A vertical multistage type of plant factory involves different levels of growing trays, which results in the problem of difference in temperature among vertically different locations. To address it, it is necessary to install air flow devices such as air flow fan and cooling/heating device at the proper locations in order to facilitate air circulation in the facility as well as develop a controlling technology for efficient operation. Accordingly, this study compares the temperature and air distribution within the space of a vertical multistage closed-type plant factory by controlling cooling/heating devices and air flow fans harmoniously by means of the specially designed testbed. The experiment results indicate that in the hybrid control of cooling and heating devices and air flow fans, the difference in temperature decreased by as much as 78.9% compared to that when only cooling and heating devices were operated; the air distribution was improved by as much as 63.4%.

  3. Metal nanoparticle mediated space charge and its optical control in an organic hole-only device

    OpenAIRE

    Ligorio, G.; Nardi, M. V.; Steyrleuthner, Robert; Ihiawakrim, D.; Crespo-Monteiro, N.; Brinkmann, M.; Neher, D.; Koch, N.

    2017-01-01

    We reveal the role of localized space charges in hole-only devices based on an organic semiconductor with embedded metal nanoparticles (MNPs). MNPs act as deep traps for holes and reduce the current density compared to a device without MNPs by a factor of 104 due to the build-up of localized space charge. Dynamic MNPs charged neutrality can be realized during operation by electron transfer from excitons created in the organic matrix, enabling light sensing independent of device bias. In contr...

  4. Design and control of a bio-inspired soft wearable robotic device for ankle-foot rehabilitation.

    Science.gov (United States)

    Park, Yong-Lae; Chen, Bor-rong; Pérez-Arancibia, Néstor O; Young, Diana; Stirling, Leia; Wood, Robert J; Goldfield, Eugene C; Nagpal, Radhika

    2014-03-01

    We describe the design and control of a wearable robotic device powered by pneumatic artificial muscle actuators for use in ankle-foot rehabilitation. The design is inspired by the biological musculoskeletal system of the human foot and lower leg, mimicking the morphology and the functionality of the biological muscle-tendon-ligament structure. A key feature of the device is its soft structure that provides active assistance without restricting natural degrees of freedom at the ankle joint. Four pneumatic artificial muscles assist dorsiflexion and plantarflexion as well as inversion and eversion. The prototype is also equipped with various embedded sensors for gait pattern analysis. For the subject tested, the prototype is capable of generating an ankle range of motion of 27° (14° dorsiflexion and 13° plantarflexion). The controllability of the system is experimentally demonstrated using a linear time-invariant (LTI) controller. The controller is found using an identified LTI model of the system, resulting from the interaction of the soft orthotic device with a human leg, and model-based classical control design techniques. The suitability of the proposed control strategy is demonstrated with several angle-reference following experiments.

  5. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Jarillo-Herrero, Pablo [Massachusetts Inst. of Technology (MIT), Cambridge, MA (United States)

    2017-02-07

    This is the final report of our research program on electronic transport experiments on Topological Insulator (TI) devices, funded by the DOE Office of Basic Energy Sciences. TI-based electronic devices are attractive as platforms for spintronic applications, and for detection of emergent properties such as Majorana excitations , electron-hole condensates , and the topological magneto-electric effect . Most theoretical proposals envision geometries consisting of a planar TI device integrated with materials of distinctly different physical phases (such as ferromagnets and superconductors). Experimental realization of physics tied to the surface states is a challenge due to the ubiquitous presence of bulk carriers in most TI compounds as well as degradation during device fabrication.

  6. Classification of two steroids, prostanozol and methasterone, as Schedule III anabolic steroids under the Controlled Substance Act. Final rule.

    Science.gov (United States)

    2012-07-30

    With the issuance of this Final Rule, the Administrator of the DEA classifies the following two steroids as "anabolic steroids'' under the Controlled Substances Act (CSA): prostanozol (17[beta]-hydroxy-5[alpha]-androstano[3,2-c]pyrazole) and methasterone (2[alpha],17[alpha]-dimethyl-5[alpha]-androstan-17[beta]-ol-3-one). These steroids and their salts, esters, and ethers are Schedule III controlled substances subject to the regulatory control provisions of the CSA.

  7. SisterTalk: final results of a culturally tailored cable television delivered weight control program for Black women

    OpenAIRE

    Risica, Patricia Markham; Gans, Kim M.; Kumanyika, Shiriki; Kirtania, Usree; Lasater, Thomas M

    2013-01-01

    Background Obesity among Black women continues to exceed that of other women. Most weight loss programs created without reference to specific cultural contexts are less effective for Black than White women. Weight control approaches accessible to Black women and adapted to relevant cultural contexts are important for addressing this problem. This paper reports the final results of SisterTalk, the randomized controlled trial of a cable TV weight control program oriented toward Black women. Met...

  8. Impact of the Volkswagen emissions control defeat device on US public health

    Science.gov (United States)

    Barrett, Steven R. H.; Speth, Raymond L.; Eastham, Sebastian D.; Dedoussi, Irene C.; Ashok, Akshay; Malina, Robert; Keith, David W.

    2015-11-01

    The US Environmental Protection Agency (EPA) has alleged that Volkswagen Group of America (VW) violated the Clean Air Act (CAA) by developing and installing emissions control system ‘defeat devices’ (software) in model year 2009-2015 vehicles with 2.0 litre diesel engines. VW has admitted the inclusion of defeat devices. On-road emissions testing suggests that in-use NOx emissions for these vehicles are a factor of 10 to 40 above the EPA standard. In this paper we quantify the human health impacts and associated costs of the excess emissions. We propagate uncertainties throughout the analysis. A distribution function for excess emissions is estimated based on available in-use NOx emissions measurements. We then use vehicle sales data and the STEP vehicle fleet model to estimate vehicle distance traveled per year for the fleet. The excess NOx emissions are allocated on a 50 km grid using an EPA estimate of the light duty diesel vehicle NOx emissions distribution. We apply a GEOS-Chem adjoint-based rapid air pollution exposure model to produce estimates of particulate matter and ozone exposure due to the spatially resolved excess NOx emissions. A set of concentration-response functions is applied to estimate mortality and morbidity outcomes. Integrated over the sales period (2008-2015) we estimate that the excess emissions will cause 59 (95% CI: 10 to 150) early deaths in the US. When monetizing premature mortality using EPA-recommended data, we find a social cost of ˜450m over the sales period. For the current fleet, we estimate that a return to compliance for all affected vehicles by the end of 2016 will avert ˜130 early deaths and avoid ˜840m in social costs compared to a counterfactual case without recall.

  9. Investigating motorists' behaviors in response to supplementary traffic control devices at land surveying work sites.

    Science.gov (United States)

    Yang, Hong; Bartin, Bekir; Ozbay, Kaan; Chien, Steven I-Jy

    2014-01-01

    Since land surveyors working alongside live traffic encounter unique safety challenges there is a great need for innovative and effective traffic control devices (TCDs) that alert motorists approaching short-term land surveying work sites. Unlike the volume of research that has been completed on traditional work zones, however, there is a limited amount of information that has been collected on how motorists respond to TCDs at land surveying work sites. This article aims to fill the void by investigating motorists' behaviors in response to the use of 2 supplementary TCDs at land surveying work sites: portable plastic rumble strips (PPRS) and warning lights. Extensive field tests were conducted at various land surveying work sites on 2-lane 2-way urban roadways in New Jersey. Scenarios with and without the use of the supplemental TCDs were designed. Motorists' behavior changes were then statistically examined by using surrogate safety measures including mean speed, speed variance, speed limit compliance, and braking action. Statistical analyses showed that the traffic speed variations did not significantly increase when the selected supplemental TCD was used; rather, motorists significantly reduced their driving speed. When warning lights and PPRS were separately deployed at the land surveying work sites the average reduction in mean speed was 6.7 and 15.2 percent, respectively. The mean speed was reduced by 19.7 percent when both of these supplementary TCDs were used. Logistic regression models developed to examine the speeding and braking behavior also showed that motorists were more likely to comply with the speed limit and increase their braking rate when the selected TCDs were used. The use of supplemental TCDs can greatly contribute to the changes in motorists' behaviors at surveying work sites. The changes in motorists' driving behaviors imply that the motorists reacted favorably to the deployed TCDs at the land-surveying work sites.

  10. Development of a Mechatronic Syringe Pump to Control Fluid Flow in a Microfluidic Device Based on Polyimide Film

    Science.gov (United States)

    Sek Tee, Kian; Sharil Saripan, Muhammad; Yap, Hiung Yin; Fhong Soon, Chin

    2017-08-01

    With the advancement in microfluidic technology, fluid flow control for syringe pump is always essential. In this paper, a mechatronic syringe pump will be developed and customized to control the fluid flow in a poly-dimethylsiloxane (PDMS) microfluidic device based on a polyimide laminating film. The syringe pump is designed to drive fluid with flow rates of 100 and 1000 μl/min which intended to drive continuous fluid in a polyimide based microfluidic device. The electronic system consists of an Arduino microcontroller board and a uni-polar stepper motor. In the system, the uni-polar stepper motor was coupled to a linear slider attached to the plunger of a syringe pump. As the motor rotates, the plunger pumps the liquid out of the syringe. The accuracy of the fluid flow rate was determined by adjusting the number of micro-step/revolution to drive the stepper motor to infuse fluid into the microfluidic device. With the precise control of the electronic system, the syringe pump could accurately inject fluid volume at 100 and 1000 μl/min into a microfluidic device.

  11. Controllable gas in oil in water double emulsion formation in a non-planar microfluidic device

    Science.gov (United States)

    Huang, Cong; Zhang, Hong-Bo; Koch, Katharina K. C.; Yin, Rui-Xue; Zhang, Wen-Jun

    2017-02-01

    We present a simple yet robust way to fabricate mono-dispersed gas-in-oil-in-water (G/O/W) double emulsions in a non-planar microfluidic device. The microfluidic device is composed of two pieces of chip which make the non-planar structure in microchannel be implemented. By manipulating the flow rate of each phase, the structure of the microbubbles can be tuned. This approach is also valid to the generation of G/W/O double emulsions.

  12. Ontology-Driven Instant Messaging-Based Dialogue System for Device Control

    KAUST Repository

    Noguera-Arnaldos, José Ángel

    2015-10-14

    The im4Things platform aims to develop a communication interface for devices in the Internet of the Things (IoT) through intelligent dialogue based on written natural language over instant messaging services. This type of communication can be established in different ways such as order sending and, status querying. Also, the devices themselves are responsible for alerting users when a change has been produced in the device’s sensors. The system has been validated and it has obtained promising results.

  13. Speech Rate Control for Improving Elderly Speech Recognition of Smart Devices

    Directory of Open Access Journals (Sweden)

    SON, G.

    2017-05-01

    Full Text Available Although smart devices have become a widely-adopted tool for communication in modern society, it still requires a steep learning curve among the elderly. By introducing a voice-based interface for smart devices using voice recognition technology, smart devices can become more user-friendly and useful to the elderly. However, the voice recognition technology used in current devices is attuned to the voice patterns of the young. Therefore, speech recognition falters when an elderly user speaks into the device. This paper has identified that the elderly's improper speech rate by each syllable contributes to the failure in the voice recognition system. Thus, upon modifying the speech rate by each syllable, the voice recognition rate saw an increase of 12.3%. This paper demonstrates that by simply modifying the speech rate by each syllable, which is one of the factors that causes errors in voice recognition, the recognition rate can be substantially increased. Such improvements in voice recognition technology can make it easier for the elderly to operate smart devices that will allow them to be more socially connected in a mobile world and access information at their fingertips. It may also be helpful in bridging the communication divide between generations.

  14. Scientific Ground of a New Optical Device for Contactless Measurement of the Small Spatial Displacements of Control Object Surfaces

    Science.gov (United States)

    Miroshnichenko, I. P.; Parinov, I. A.

    2017-06-01

    It is proposed the computational-experimental ground of newly developed optical device for contactless measurement of small spatial displacements of control object surfaces based on the use of new methods of laser interferometry. The proposed device allows one to register linear and angular components of the small displacements of control object surfaces during the diagnosis of the condition of structural materials for forced elements of goods under exploring by using acoustic non-destructive testing methods. The described results are the most suitable for application in the process of high-precision measurements of small linear and angular displacements of control object surfaces during experimental research, the evaluation and diagnosis of the state of construction materials for forced elements of goods, the study of fast wave propagation in layered constructions of complex shape, manufactured of anisotropic composite materials, the study of damage processes in modern construction materials in mechanical engineering, shipbuilding, aviation, instrumentation, power engineering, etc.

  15. Standardizing visual control devices for tsetse flies: West African species Glossina tachinoides, G. palpalis gambiensis and G. morsitans submorsitans.

    Directory of Open Access Journals (Sweden)

    Jean-Baptiste Rayaisse

    Full Text Available Here we describe field trials designed to standardize tools for the control of Glossina tachinoides, G. palpalis gambiensis and G.morsitans submorsitans in West Africa based on existing trap/target/bait technology. Blue and black biconical and monoconical traps and 1 m(2 targets were made in either phthalogen blue cotton, phthalogen blue cotton/polyester or turquoise blue polyester/viscose (all with a peak reflectance between 450-480 nm and a black polyester. Because targets were covered in adhesive film, they proved to be significantly better trapping devices than either of the two trap types for all three species (up to 14 times more for G. tachinoides, 10 times more for G. palpalis gambiensis, and 6.5 times for G. morsitans submorsitans. The relative performance of the devices in the three blue cloths tested was the same when unbaited or baited with a mixture of phenols, 1-octen-3-ol and acetone. Since insecticide-impregnated devices act via contact with flies, we enumerated which device (traps or targets served as the best object for flies to land on by also covering the cloth parts of traps with adhesive film. Despite the fact that the biconical trap proved to be the best landing device for the three species, the difference over the target (20-30% was not significant. This experiment also allowed an estimation of trap efficiency, i.e. the proportion of flies landing on a trap that are caught in its cage. A low overall efficiency of the biconical or monoconical traps of between 11-24% was recorded for all three species. These results show that targets can be used as practical devices for population suppression of the three species studied. Biconical traps can be used for population monitoring, but a correction factor of 5-10 fold needs to be applied to captures to compensate for the poor trapping efficiency of this device for the three species.

  16. Standardizing visual control devices for tsetse flies: West African species Glossina tachinoides, G. palpalis gambiensis and G. morsitans submorsitans.

    Science.gov (United States)

    Rayaisse, Jean-Baptiste; Kröber, Thomas; McMullin, Andrew; Solano, Philippe; Mihok, Steve; Guerin, Patrick M

    2012-01-01

    Here we describe field trials designed to standardize tools for the control of Glossina tachinoides, G. palpalis gambiensis and G.morsitans submorsitans in West Africa based on existing trap/target/bait technology. Blue and black biconical and monoconical traps and 1 m(2) targets were made in either phthalogen blue cotton, phthalogen blue cotton/polyester or turquoise blue polyester/viscose (all with a peak reflectance between 450-480 nm) and a black polyester. Because targets were covered in adhesive film, they proved to be significantly better trapping devices than either of the two trap types for all three species (up to 14 times more for G. tachinoides, 10 times more for G. palpalis gambiensis, and 6.5 times for G. morsitans submorsitans). The relative performance of the devices in the three blue cloths tested was the same when unbaited or baited with a mixture of phenols, 1-octen-3-ol and acetone. Since insecticide-impregnated devices act via contact with flies, we enumerated which device (traps or targets) served as the best object for flies to land on by also covering the cloth parts of traps with adhesive film. Despite the fact that the biconical trap proved to be the best landing device for the three species, the difference over the target (20-30%) was not significant. This experiment also allowed an estimation of trap efficiency, i.e. the proportion of flies landing on a trap that are caught in its cage. A low overall efficiency of the biconical or monoconical traps of between 11-24% was recorded for all three species. These results show that targets can be used as practical devices for population suppression of the three species studied. Biconical traps can be used for population monitoring, but a correction factor of 5-10 fold needs to be applied to captures to compensate for the poor trapping efficiency of this device for the three species.

  17. Matching Automatic Gain Control Across Devices in Bimodal Cochlear Implant Users.

    Science.gov (United States)

    Veugen, Lidwien C E; Chalupper, Josef; Snik, Ad F M; Opstal, A John van; Mens, Lucas H M

    2016-01-01

    The purpose of this study was to improve bimodal benefit in listeners using a cochlear implant (CI) and a hearing aid (HA) in contralateral ears, by matching the time constants and the number of compression channels of the automatic gain control (AGC) of the HA to the CI. Equivalent AGC was hypothesized to support a balanced loudness for dynamically changing signals like speech and improve bimodal benefit for speech understanding in quiet and with noise presented from the side(s) at 90 degree. Fifteen subjects participated in the study, all using the same Advanced Bionics Harmony CI processor and HA (Phonak Naida S IX UP). In a 3-visit crossover design with 4 weeks between sessions, performance was measured using a HA with a standard AGC (syllabic multichannel compression with 1 ms attack time and 50 ms release time) or an AGC that was adjusted to match that of the CI processor (dual AGC broadband compression, 3 and 240 msec attack time, 80 and 1500 msec release time). In all devices, the AGC was activated above the threshold of 63 dB SPL. The authors balanced loudness across the devices for soft and loud input sounds in 3 frequency bands (0 to 548, 548 to 1000, and >1000 Hz). Speech understanding was tested in free field in quiet and in noise for three spatial speaker configurations, with target speech always presented from the front. Single-talker noise was either presented from the CI side or the HA side, or uncorrelated stationary speech-weighted noise or single-talker noise was presented from both sides. Questionnaires were administered to assess differences in perception between the two bimodal fittings. Significant bimodal benefit over the CI alone was only found for the AGC-matched HA for the speech tests with single-talker noise. Compared with the standard HA, matched AGC characteristics significantly improved speech understanding in single-talker noise by 1.9 dB when noise was presented from the HA side. AGC matching increased bimodal benefit

  18. Parametric optimization in virtual prototyping environment of the control device for a robotic system used in thin layers deposition

    Science.gov (United States)

    Enescu (Balaş, M. L.; Alexandru, C.

    2016-08-01

    The paper deals with the optimal design of the control system for a 6-DOF robot used in thin layers deposition. The optimization is based on parametric technique, by modelling the design objective as a numerical function, and then establishing the optimal values of the design variables so that to minimize the objective function. The robotic system is a mechatronic product, which integrates the mechanical device and the controlled operating device.The mechanical device of the robot was designed in the CAD (Computer Aided Design) software CATIA, the 3D-model being then transferred to the MBS (Multi-Body Systems) environment ADAMS/View. The control system was developed in the concurrent engineering concept, through the integration with the MBS mechanical model, by using the DFC (Design for Control) software solution EASY5. The necessary angular motions in the six joints of the robot, in order to obtain the imposed trajectory of the end-effector, have been established by performing the inverse kinematic analysis. The positioning error in each joint of the robot is used as design objective, the optimization goal being to minimize the root mean square during simulation, which is a measure of the magnitude of the positioning error varying quantity.

  19. Effect of device-guided breathing exercises on blood pressure in patients with hypertension: a randomized controlled trial.

    Science.gov (United States)

    Altena, Mariette R; Kleefstra, Nanne; Logtenberg, Susan J; Groenier, Klaas H; Houweling, Sebastiaan T; Bilo, Henk J

    2009-01-01

    Hypertension is a chronic disorder with a high prevalence worldwide. Despite considerable efforts, it is sometimes hard to reach treatment goals for blood pressure (BP) with classical treatment options. Reducing breathing frequency has been advocated as a method to reduce BP. A randomized, single-blind, controlled trial was conducted in 30 non-diabetic patients with hypertension over a period of 9 weeks to evaluate the effect of a device that helps to slow breathing (Resperate) on BP and quality of life (QoL). The control group listened to music and used no other therapeutic device. There was no significant difference in change in BP between intervention and control; BP -4.2 mmHg (95% CI -12.4 to 3.9)/-2.6 mmHg (95% CI -8.4 to 3.3). This result did not alter in post hoc analyses, when patients not achieving target breathing frequency (<10 breaths/min) or non-compliant patients were excluded. QoL did not change over time. We found no effect of the Resperate on BP or QoL compared with the control group. We conclude that, at this moment, this device has no added value in the treatment of hypertension.

  20. A design handbook for phase change thermal control and energy storage devices. [selected paraffins

    Science.gov (United States)

    Humphries, W. R.; Griggs, E. I.

    1977-01-01

    Comprehensive survey is given of the thermal aspects of phase change material devices. Fundamental mechanisms of heat transfer within the phase change device are discussed. Performance in zero-g and one-g fields are examined as it relates to such a device. Computer models for phase change materials, with metal fillers, undergoing conductive and convective processes are detailed. Using these models, extensive parametric data are presented for a hypothetical configuration with a rectangular phase change housing, using straight fins as the filler, and paraffin as the phase change material. These data are generated over a range of realistic sizes, material properties, and thermal boundary conditions. A number of illustrative examples are given to demonstrate use of the parametric data. Also, a complete listing of phase change material property data are reproduced herein as an aid to the reader.

  1. Suspended graphene devices with local gate control on an insulating substrate.

    Science.gov (United States)

    Ong, Florian R; Cui, Zheng; Yurtalan, Muhammet A; Vojvodin, Cameron; Papaj, Michał; Orgiazzi, Jean-Luc F X; Deng, Chunqing; Bal, Mustafa; Lupascu, Adrian

    2015-10-09

    We present a fabrication process for graphene-based devices where a graphene monolayer is suspended above a local metallic gate placed in a trench. As an example we detail the fabrication steps of a graphene field-effect transistor. The devices are built on a bare high-resistivity silicon substrate. At temperatures of 77 K and below, we observe the field-effect modulation of the graphene resistivity by a voltage applied to the gate. This fabrication approach enables new experiments involving graphene-based superconducting qubits and nano-electromechanical resonators. The method is applicable to other two-dimensional materials.

  2. Voltage controlled Bi-mode resistive switching effects in MnO2 based devices

    Science.gov (United States)

    Hu, P.; Wu, S. X.; Wang, G. L.; Li, H. W.; Li, D.; Li, S. W.

    2018-01-01

    In this paper, the voltage induced bi-mode resistive switching behavior of an MnO2 thin film based device was studied. The device showed prominent bipolar resistive switching behavior with good reproducibility and high endurance. In addition, complementary resistive switching characteristics can be observed by extending the voltage bias during voltage sweep operations. The electrical measurement data and fitting results indicate that the oxygen vacancies act as defects to form a conductive path, which is connective or disrupted to realize a low resistive state or a high resistive state. Changing the sweep voltage can tune the oxygen vacancies distribution, which will achieve complementary resistive switching.

  3. 40 CFR 63.9324 - How do I establish the emission capture system and add-on control device operating limits during...

    Science.gov (United States)

    2010-07-01

    ... capture system and add-on control device operating limits during the performance test? 63.9324 Section 63... Requirements § 63.9324 How do I establish the emission capture system and add-on control device operating... the operating limits required by § 63.9302 according to this section, unless you have received...

  4. 40 CFR 63.3967 - How do I establish the emission capture system and add-on control device operating limits during...

    Science.gov (United States)

    2010-07-01

    ... system and add-on control device operating limits during the performance test? 63.3967 Section 63.3967... capture system and add-on control device operating limits during the performance test? During the... the operating limits required by § 63.3892 according to this section, unless you have received...

  5. 40 CFR 60.1815 - How do I monitor the temperature of flue gases at the inlet of my particulate matter control device?

    Science.gov (United States)

    2010-07-01

    ... I monitor the temperature of flue gases at the inlet of my particulate matter control device? You... 40 Protection of Environment 6 2010-07-01 2010-07-01 false How do I monitor the temperature of flue gases at the inlet of my particulate matter control device? 60.1815 Section 60.1815 Protection of...

  6. A Framework for a General Purpose Intelligent Control System for Particle Accelerators. Phase II Final Report

    Energy Technology Data Exchange (ETDEWEB)

    Dr. Robert Westervelt; Dr. William Klein; Dr. Michael Kroupa; Eric Olsson; Rick Rothrock

    1999-06-28

    Vista Control Systems, Inc. has developed a portable system for intelligent accelerator control. The design is general in scope and is thus configurable to a wide range of accelerator facilities and control problems. The control system employs a multi-layer organization in which knowledge-based decision making is used to dynamically configure lower level optimization and control algorithms.

  7. Modeling of endoluminal and interstitial ultrasound hyperthermia and thermal ablation: applications to device design, feedback control, and treatment planning

    Science.gov (United States)

    Prakash, Punit; Salgaonkar, Vasant A.; Diederich, Chris J.

    2014-01-01

    Endoluminal and catheter-based ultrasound applicators are currently under development and are in clinical use for minimally invasive hyperthermia and thermal ablation of various tissue targets. Computational models play a critical role in in device design and optimization, assessment of therapeutic feasibility and safety, devising treatment monitoring and feedback control strategies, and performing patient-specific treatment planning with this technology. The critical aspects of theoretical modeling, applied specifically to endoluminal and interstitial ultrasound thermotherapy, are reviewed. Principles and practical techniques for modeling acoustic energy deposition, bioheat transfer, thermal tissue damage, and dynamic changes in the physical and physiological state of tissue are reviewed. The integration of these models and applications of simulation techniques in identification of device design parameters, development of real time feedback-control platforms, assessing the quality and safety of treatment delivery strategies, and optimization of inverse treatment plans are presented. PMID:23738697

  8. Modelling of endoluminal and interstitial ultrasound hyperthermia and thermal ablation: applications for device design, feedback control and treatment planning.

    Science.gov (United States)

    Prakash, Punit; Salgaonkar, Vasant A; Diederich, Chris J

    2013-06-01

    Endoluminal and catheter-based ultrasound applicators are currently under development and are in clinical use for minimally invasive hyperthermia and thermal ablation of various tissue targets. Computational models play a critical role in device design and optimisation, assessment of therapeutic feasibility and safety, devising treatment monitoring and feedback control strategies, and performing patient-specific treatment planning with this technology. The critical aspects of theoretical modelling, applied specifically to endoluminal and interstitial ultrasound thermotherapy, are reviewed. Principles and practical techniques for modeling acoustic energy deposition, bioheat transfer, thermal tissue damage, and dynamic changes in the physical and physiological state of tissue are reviewed. The integration of these models and applications of simulation techniques in identification of device design parameters, development of real time feedback-control platforms, assessing the quality and safety of treatment delivery strategies, and optimisation of inverse treatment plans are presented.

  9. Seafood industry hazard analysis critical control point workshops and model tests lobster products: final report

    National Research Council Canada - National Science Library

    1990-01-01

    .... They concluded that there are six critical control points in processing American lobster and eighty for spiny lobster which can serve as controls to ensure product safety and to control economic malpractice...

  10. Design, fabrication and test of a pneumatically controlled, renewable, microfluidic bead trapping device for sequential injection analysis applications

    Energy Technology Data Exchange (ETDEWEB)

    Shao, Guocheng; Lu, Donglai; Fu, Zhifeng; Du, Dan; Ozanich, Richard M.; Wang, Wanjun; Lin, Yuehe

    2016-01-01

    This paper describes the design, fabrication, and testing of a pneumatically controlled,renewable, microfluidic device for conducting bead-based assays in an automated sequential injection analysis system. The device used a “brick wall”-like pillar array (pillar size: 20 μm length X 50 μm width X 45 μm height) with 5 μm gaps between the pillars serving as the micro filter. The flow channel where bead trapping occurred is 500 μm wide X 75 μm deep. An elastomeric membrane and an air chamber were located underneath the flow channel. By applying pressure to the air chamber, the membrane is deformed and pushed upward against the filter structure. This effectively traps beads larger than 5 μm and creates a “bed” or micro column of beads that can be perfused and washed with liquid samples and reagents. Upon completion of the assay process, the pressure is released and the beads are flushed out from underneath the filter structure to renew the device. Mouse IgG was used as a model analyte to test the feasibility of using the proposed device for immunoassay applications. Resulting microbeads from an on-chip fluorescent immunoassay were individually examined using flow cytometry. The results show that the fluorescence signal intensity distribution is fairly narrow indicating high chemical reaction uniformity among the beads population. Electrochemical onchip assay was also conducted. A detection limit of 0.1 ng/mL1 ppb was achieved and good device reliability and repeatability were demonstrated. The novel microfluidic-based beadstrapping device thus opens up a new pathway to design micro-bead based biosensor immunoassays for clinical and othervarious applications.

  11. Design, Development and Implementation of a Smartphone Overdependence Management System for the Self-Control of Smart Devices

    OpenAIRE

    Seo-Joon Lee; Mi Jung Rho; In Hye Yook; Seung-Ho Park; Kwang-Soo Jang; Bum-Joon Park; Ook Lee; Dong Kyun Lee; Dai-Jin Kim; In Young Choi

    2016-01-01

    Background: Smartphone overdependence is a type of mental disorder that requires continuous treatment for cure and prevention. A smartphone overdependence management system that is based on scientific evidence is required. This study proposes the design, development and implementation of a smartphone overdependence management system for self-control of smart devices. Methods: The system architecture of the Smartphone Overdependence Management System (SOMS) primarily consists of four sessions ...

  12. Final Technical Report: Numerical and Experimental Investigation of Turbulent Transport Control via Shaping of Radial Plasma Flow Profiles

    Energy Technology Data Exchange (ETDEWEB)

    Schuster, Eugenio

    2014-05-02

    The strong coupling between the different physical variables involved in the plasma transport phenomenon and the high complexity of its dynamics call for a model-based, multivariable approach to profile control where those predictive models could be exploited. The overall objective of this project has been to extend the existing body of work by investigating numerically and experimentally active control of unstable fluctuations, including fully developed turbulence and the associated cross-field particle transport, via manipulation of flow profiles in a magnetized laboratory plasma device. Fluctuations and particle transport can be monitored by an array of electrostatic probes, and Ex B flow profiles can be controlled via a set of biased concentric ring electrodes that terminate the plasma column. The goals of the proposed research have been threefold: i- to develop a predictive code to simulate plasma transport in the linear HELCAT (HELicon-CAThode) plasma device at the University of New Mexico (UNM), where the experimental component of the proposed research has been carried out; ii- to establish the feasibility of using advanced model-based control algorithms to control cross-field turbulence-driven particle transport through appropriate manipulation of radial plasma flow profiles, iii- to investigate the fundamental nonlinear dynamics of turbulence and transport physics. Lehigh University (LU), including Prof. Eugenio Schuster and one full-time graduate student, has been primarily responsible for control-oriented modeling and model-based control design. Undergraduate students have also participated in this project through the National Science Foundation Research Experience for Undergraduate (REU) program. The main goal of the LU Plasma Control Group has been to study the feasibility of controlling turbulence-driven transport by shaping the radial poloidal flow profile (i.e., by controlling flow shear) via biased concentric ring electrodes.

  13. Electrowetting-controlled droplet generation in a microfluidic flow-focusing device

    NARCIS (Netherlands)

    Malloggi, F.G.J.; Vanapalli, Srinivas; Vanapalli Veera, V.S.A.R.; Gu, H.; van den Ende, Henricus T.M.; Mugele, Friedrich Gunther

    2007-01-01

    We studied the generation of aqueous microdrops in an oil–water flow-focusing device with integrated insulator-covered electrodes that allow for continuous tuning of the water wettability by means of electrowetting. Depending on the oil and water inlet pressures three different operating conditions

  14. 78 FR 79300 - Cardiovascular Devices; Reclassification of Intra-Aortic Balloon and Control Systems for Acute...

    Science.gov (United States)

    2013-12-30

    ... recommendation from a device classification panel (an FDA advisory committee); (2) published the panel's... upon ``valid scientific evidence'' in the classification process to determine the level of regulation... and/or confidential commercial information, e.g., the contents of a pending PMA. (See section 520(c...

  15. A novel device reduces anal pain after rubber band ligation: a randomized controlled trial

    NARCIS (Netherlands)

    Lam, T.J.; Felt-Bersma, R.J.F.

    2012-01-01

    Background Anal pain is a well-known sequel of rubber band ligation (RBL). A plastic device, the anal cooler which can be frozen in a freezer, has been developed to reduce anal pain. It contains a mixture of glycols and has a minimum temperature of 4 °C. This study was designed to investigate the

  16. Probe data from consumer GPS navigation devices for the analysis of controlled intersections

    NARCIS (Netherlands)

    Van Arem, B.; Salomons, A.M.; Krootjes, P.; Cohn, N.; Meijer, A.

    2012-01-01

    Probe data from consumer GPS navigation devices provides a network-wide and costefficient data source for measuring vehicle movements, whereas experimental studies have been confined to small datasets. Data collection from road-side sensors can provide similar information but is expensive and

  17. Efficient Implementation of Solvers for Linear Model Predictive Control on Embedded Devices

    DEFF Research Database (Denmark)

    Frison, Gianluca; Kwame Minde Kufoalor, D.; Imsland, Lars

    2014-01-01

    of a single routine (the matrix-matrix multiplication gemm) can speed-up an interior-point method for linear MPC. The results show that the high-performance MPC obtained using the proposed approach is several times faster than the current state-of-the-art IP method for linear MPC on embedded devices....

  18. Wireless Coexistence and EMC of Bluetooth and 802.11b Devices in Controlled Laboratory Settings.

    Science.gov (United States)

    Seidman, Seth; Kainz, Wolfgang; Ruggera, Paul; Mendoza, Gonzalo

    2011-01-01

    This paper presents experimental testing that has been performed on wireless communication devices as victims of electromagnetic interference (EMI). Wireless victims included universal serial bus (USB) network adapters and personal digital assistants (PDAs) equipped with IEEE 802.11b and Bluetooth technologies. The experimental data in this paper was gathered in an anechoic chamber and a gigahertz transverse electromagnetic (GTEM) cell to ensure reliable and repeatable results. This testing includes: Electromagnetic compatibility (EMC) testing performed in accordance with IEC 60601-1-2, an in-band sweep of EMC testing, and coexistence testing. The tests in this study show that a Bluetooth communication was able to coexist with other Bluetooth devices with no decrease in throughput and no communication breakdowns. However, testing revealed a significant decrease in throughput and increase in communication breakdowns when an 802.11b source is near an 802.11b victim. In a hospital setting decreased throughput and communication breakdowns can cause wireless medical devices to fail. It is therefore vital to have an understanding of the effect EMI can have on wireless communication devices.

  19. DoD Comprehensive Military Unmanned Aerial Vehicle Smart Device Ground Control Station Threat Model

    Science.gov (United States)

    2015-04-01

    thereby increasing the chances that phishing, spam , mal- ware, and spyware will infiltrate the system (Leavitt, 2011). Maintainers of the smart device...as spam and phishing. Communication from outside the secure network should be blocked. Spam filters can also be used to prevent receipt of spam

  20. im4Things: An Ontology-Based Natural Language Interface for Controlling Devices in the Internet of Things

    KAUST Repository

    Noguera-Arnaldos, José Ángel

    2017-03-14

    The Internet of Things (IoT) offers opportunities for new applications and services that enable users to access and control their working and home environment from local and remote locations, aiming to perform daily life activities in an easy way. However, the IoT also introduces new challenges, some of which arise from the large range of devices currently available and the heterogeneous interfaces provided for their control. The control and management of this variety of devices and interfaces represent a new challenge for non-expert users, instead of making their life easier. Based on this understanding, in this work we present a natural language interface for the IoT, which takes advantage of Semantic Web technologies to allow non-expert users to control their home environment through an instant messaging application in an easy and intuitive way. We conducted several experiments with a group of end users aiming to evaluate the effectiveness of our approach to control home appliances by means of natural language instructions. The evaluation results proved that without the need for technicalities, the user was able to control the home appliances in an efficient way.