Resistivity and Induced Polarization Imaging at a Hydrocarbon Contaminated Site in Brazil

Science.gov (United States)

Ustra, A.; Elis, V.; Hiodo, F.; Bondioli, A.; Miura, G.

2012-12-01

An area contaminated by accidental BTEX spills was investigated with resistivity and induced polarization methods. The main objective in this study was to relate the geophysical signature of the area with zones that were possibly undergoing microbial degradation of the contaminants. The spills took place over a decade ago; however, the exact location of these spills is unknown, as well as the amount of contaminant that was released into the subsurface. DC-resistivity identified a high contrast between the background (rho up to 2000 ohm.m) and a relatively conductive zone (rho 30 mV/V). Normalized chargeability is enhanced in this anomaly zone (mn > 0.1). Soil samples collected in the area were submitted to direct bacterial count, clay content estimation, X-ray diffraction and SEM analysis. The electrical properties of each samples was also measured. The samples collected from the "background" (high resistivity zone) presented total bacterial amounts much smaller (dozens of colony forming units) than the samples from the conductive zone (millions of colony forming units). This observation could lead us to interpret that the zone of higher bacteria amount is undergoing biodegradation that would explain the increased conductivity at that portion of the subsurface. However, the geophysical properties observed at this zone could also be related to the clay content distribution throughout the surveyed area (concentrations up to 30%). Moreover, despite the fact that more microbes were found in the area, SEM images did not find any biodegradation typical feature of the grains, which are for example, mineral corrosion and dissolution or even biomineralization. This study is still undergoing and we are searching for more evidence of biodegradation in the samples. This study shows the limitation of the use of geophysical methods to access contaminant presence and/or biodegradation zones when the exact location of the contamination is unknown.

New DUV resist characterisation: stability to MB SEMI F21-95 contaminants

International Nuclear Information System (INIS)

Curro, T.; Cordiano, F.; Franco, G.; Mondio, G.; Ippedico, G.

2004-01-01

Airborne molecular contamination (AMC) effects reveal to be more and more prominent in clean room manufacturing areas, shrinking the dimensions of electronic circuits such as the last generation of flash memory devices (0.15-0.13 μm). This work enabled us to evaluate new resist stability to specific airborne contamination class in critical conditions; that is basic contamination of clean room environments (∼20 ppb), higher than a typical contamination status inside Deep UV equipment chambers (∼2 ppb). Formation of the so-called T-Topping (see Fig. 1) was observed, qualitatively discussed and quantitatively measured, facilitating comparison between experimental data on a time scale basis and a theoretical model developed for interpret contaminants adsorption on ultra clean surfaces; then we interpolated critical data between 1 and 5 min to gather information on process material characterization. The starting adsorption shift rate revealed to be 12 nm/min, showing that T-Topping is an almost instantaneous phenomena and that 2 min are sufficient to obtain CD values higher than specification limits in the experimental conditions. Finally, we calculated the resist characterization parameter (max shift rate per ppbV of airborne basis concentration) on a pure theoretical basis (0.637 nm/min/ppbV) resulting in a very good agreement with literature [D. Kinkead, W. Goodwin, K., MICRO 18(9) (2000) 71-84

Identification of seed proteins associated with resistance to pre-harvested aflatoxin contamination in peanut (Arachis hypogaea L

Directory of Open Access Journals (Sweden)

Li Ling

2010-11-01

Full Text Available Abstract Background Pre-harvest infection of peanuts by Aspergillus flavus and subsequent aflatoxin contamination is one of the food safety factors that most severely impair peanut productivity and human and animal health, especially in arid and semi-arid tropical areas. Some peanut cultivars with natural pre-harvest resistance to aflatoxin contamination have been identified through field screening. However, little is known about the resistance mechanism, which has slowed the incorporation of resistance into cultivars with commercially acceptable genetic background. Therefore, it is necessary to identify resistance-associated proteins, and then to recognize candidate resistance genes potentially underlying the resistance mechanism. Results The objective of this study was to identify resistance-associated proteins in response to A. flavus infection under drought stress using two-dimensional electrophoresis with mass spectrometry. To identify proteins involved in the resistance to pre-harvest aflatoxin contamination, we compared the differential expression profiles of seed proteins between a resistant cultivar (YJ-1 and a susceptible cultivar (Yueyou 7 under well-watered condition, drought stress, and A. flavus infection with drought stress. A total of 29 spots showed differential expression between resistant and susceptible cultivars in response to A. flavus attack under drought stress. Among these spots, 12 protein spots that consistently exhibited an altered expression were screened by Image Master 5.0 software and successfully identified by MALDI-TOF MS. Five protein spots, including Oso7g0179400, PII protein, CDK1, Oxalate oxidase, SAP domain-containing protein, were uniquely expressed in the resistant cultivar. Six protein spots including low molecular weight heat shock protein precursor, RIO kinase, L-ascorbate peroxidase, iso-Ara h3, 50 S ribosomal protein L22 and putative 30 S ribosomal S9 were significantly up-regulated in the resistant

Methicillin resistant Staphylococcus aureus contamination of phlebotomy tourniquets and faucets

Science.gov (United States)

Abeywickrama, T; Amarasinghe, K; Wijerathne, S; Dharmaratne, C; Fernando, D; Senaratna, B C; Gunasekera, H A K M

2018-03-31

Methicillin resistant Staphylococcus aureus (MRSA) is transmitted through direct contact or fomites. The most important means of nosocomial spread is by hospital personnel. However, fomites are being increasingly recognized as sources of nosocomial infection. Our aim was to describe the MRSA contamination rate of phlebotomy tourniquets and faucets in a tertiary care hospital and to compare the contamination of plastic tourniquets with that of fabric tourniquets. A cross-sectional study was carried out in the general wards of a tertiary care hospital in the Colombo District. Two hundred tourniquets were collected and 100 faucets were swabbed and cultured on CHROMagar™ MRSA medium (CHROMagar Microbiology). Contamination rates of 50 plastic tourniquets and 50 fabric tourniquets were compared. MRSA grew in 26% of tourniquets. Majority were plastic tubes. MRSA contamination of tourniquets did not significantly differ by ward (p>0.4). MRSA was found on 26% of faucets. Contamination rate was highest in the common wards for dermatology, dental, rheumatology, and neurology (55.6%), followed by gynaecology (45.2%), cardiology (33.3%), surgery (18.8%), psychiatry (11.1%), and medicine (5.6%). There was a significant difference in rates of contamination of faucets in the different wards (pcontamination rates of tourniquets and faucets were high. Single-use plastic tourniquets were much less contaminated with MRSA than reused tourniquets.

Low resistance bakelite RPC study for high rate working capability

International Nuclear Information System (INIS)

Dai, T.; Han, L.; Hou, S.; Liu, M.; Li, Q.; Song, H.; Xia, L.; Zhang, Z.

2014-01-01

This paper presents series efforts to lower resistance of bakelite electrode plate to improve the RPC capability under high rate working condition. New bakelite material with alkali metallic ion doping has been manufactured and tested. This bakelite is found unstable under large charge flux and need further investigation. A new structure of carbon-embedded bakelite RPC has been developed, which can reduce the effective resistance of electrode by a factor of 10. The prototype of the carbon-embedded chamber could function well under gamma radiation source at event rate higher than 10 kHz/cm 2 . The preliminary tests show that this kind of new structure performs as efficiently as traditional RPCs

Environmental dissemination of antibiotic resistance genes and correlation to anthropogenic contamination with antibiotics

Science.gov (United States)

Berglund, Björn

2015-01-01

Antibiotic resistance is a growing problem which threatens modern healthcare globally. Resistance has traditionally been viewed as a clinical problem, but recently non-clinical environments have been highlighted as an important factor in the dissemination of antibiotic resistance genes (ARGs). Horizontal gene transfer (HGT) events are likely to be common in aquatic environments; integrons in particular are well suited for mediating environmental dissemination of ARGs. A growing body of evidence suggests that ARGs are ubiquitous in natural environments. Particularly, elevated levels of ARGs and integrons in aquatic environments are correlated to proximity to anthropogenic activities. The source of this increase is likely to be routine discharge of antibiotics and resistance genes, for example, via wastewater or run-off from livestock facilities and agriculture. While very high levels of antibiotic contamination are likely to select for resistant bacteria directly, the role of sub-inhibitory concentrations of antibiotics in environmental antibiotic resistance dissemination remains unclear. In vitro studies have shown that low levels of antibiotics can select for resistant mutants and also facilitate HGT, indicating the need for caution. Overall, it is becoming increasingly clear that the environment plays an important role in dissemination of antibiotic resistance; further studies are needed to elucidate key aspects of this process. Importantly, the levels of environmental antibiotic contamination at which resistant bacteria are selected for and HGT is facilitated at should be determined. This would enable better risk analyses and facilitate measures for preventing dissemination and development of antibiotic resistance in the environment. PMID:26356096

Radiation Resistant Hybrid Lotus Effect Photoelectrocatalytic Self-Cleaning Anti-Contamination Coatings, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — This project will develop radiation resistant hybrid Lotus Effect photoelectrocatalytic self-cleaning anti-contamination coatings for application to Lunar...

ADAPTIVE MONITORING TO ENHANCE WATER SENSOR CAPABILITIES FOR CHEMICAL AND BIOLOGICAL CONTAMINANT DETECTION IN DRINKING WATER SYSTEMS

Science.gov (United States)

Optoelectronic and other conventional water quality sensors offer a potential for real-time online detection of chemical and biological contaminants in a drinking water supply and distribution system. The nature of the application requires sensors of detection capabilities at lo...

Methicillin-resistant staphylococcal contamination of cellular phones of personnel in a veterinary teaching hospital

Directory of Open Access Journals (Sweden)

Julian Timothy

2012-07-01

Full Text Available Abstract Background Hospital-associated infections are an increasing cause of morbidity and mortality in veterinary patients. With the emergence of multi-drug resistant bacteria, these infections can be particularly difficult to eradicate. Sources of hospital-associated infections can include the patients own flora, medical staff and inanimate hospital objects. Cellular phones are becoming an invaluable feature of communication within hospitals, and since they are frequently handled by healthcare personnel, there may be a potential for contamination with various pathogens. The objective of this study was to determine the prevalence of contamination of cellular phones (hospital issued and personal carried by personnel at the Ontario Veterinary College Health Sciences Centre with methicillin-resistant Staphylococcus pseudintermedius (MRSP and methicillin-resistant Staphylococcus aureus (MRSA. Results MRSP was isolated from 1.6% (2/123 and MRSA was isolated from 0.8% (1/123 of cellular phones. Only 21.9% (27/123 of participants in the study indicated that they routinely cleaned their cellular phone. Conclusions Cellular phones in a veterinary teaching hospital can harbour MRSP and MRSA, two opportunistic pathogens of significant concern. While the contamination rate was low, cellular phones could represent a potential source for infection of patients as well as infection of veterinary personnel and other people that might have contact with them. Regardless of the low incidence of contamination of cellular phones found in this study, a disinfection protocol for hospital-issued and personal cellular phones used in veterinary teaching hospitals should be in place to reduce the potential of cross-contamination.

Capabilities of Seven Species of Aquatic Macrophytes for Phytoremediation of Pentachlorophenol Contaminated Sediment

Science.gov (United States)

Zhao, Liangyuan; Guo, Weijie; Li, Qingyun; Li, Huan; Zhao, Weihua; Cao, Xiaohuan

2017-01-01

Sediments are regarded as the ultimate sink of pentachlorophenol(PCP) in aquatic environment, and capabilities of seven species of aquatic macrophytes for remediating PCP contaminated sediment were investigated. Seven species of aquatic macrophytes could significantly accelerate the degradation of PCP in sediments. Among all, canna indica L., Acorus calamus L. and Iris tectorum Maxim. can be used as efficient alternative plants for remediation of PCP contaminated sediment, which attained 98%, 92% and 88% of PCP removal in sediments, respectively. PCP was detected only in root tissues and the uptake was closely related to the root lipid contents of seven plants. The presence of seven aquatic macrophytes significantly increased microbial populations and the activities of dehydrogenase compared with control sediments, indicating that rhizosphere microorganism played important role in the remediation process. In conclusion, seven species of aquatic macrophytes may act as promising tools for the PCP phytoremediation in aquatic environment, especially Canna indica L., Acorus calamus L. and Iris tectorum Maxim.

Pollen contamination in seed mixture increases the dominance of resistance to Bt maize in Spodoptera frugiperda (Lepidoptera: Noctuidae).

Science.gov (United States)

Yang, Fei; Kerns, David L; Brown, Sebe; Head, Graham P; Huang, Fangneng

2017-11-01

Seed mixture, also called 'RIB', has been used to provide refuge populations for delaying insect resistance. Pollen contamination in RIB could result in refuge kernels of non-Bt maize expressing variable Bt proteins. Data are lacking regarding the impact of pollen contamination on evolution of resistance for ear-feeding insects. Here, we used Spodoptera frugiperda and Cry1F-maize as a model to examine if pollen contamination in RIB increases the dominance of insect resistance. Pollen contamination caused >66% refuge kernels in 5:95% (non-Bt:Bt) and 20:80% RIBs to express Cry1F protein. Survival at adult stage on pure non-Bt ears was similar (54.4-63.3%) among Cry1F-susceptible (SS), Cry1F-resistant (RR) and Cry1F-heterozygous (RS) S. frugiperda. On Bt ears, survival was similar between SS and RS (0.0-1.7%), but it was significantly less than that of RR (59.2%). On the two RIB refuge ears, survival at adult stage for RS (42.3% in 5:95% RIB; 50.0% in 20:80% RIB) was significantly higher than for SS (8.7% in 5:95% RIB; 10.0% in 20:80% RIB). The results suggest that pollen contamination in RIB could increase the dominance of resistance for ear-feeding insects by significantly reducing susceptible refuge populations and supporting higher survival of heterozygotes relative to homozygous susceptible insects. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

Resistivity and self-potential tomography applied to groundwater remediation and contaminant plumes: Sandbox and field experiments

Science.gov (United States)

Mao, D.; Revil, A.; Hort, R. D.; Munakata-Marr, J.; Atekwana, E. A.; Kulessa, B.

2015-11-01

Geophysical methods can be used to remotely characterize contaminated sites and monitor in situ enhanced remediation processes. We have conducted one sandbox experiment and one contaminated field investigation to show the robustness of electrical resistivity tomography and self-potential (SP) tomography for these applications. In the sandbox experiment, we injected permanganate in a trichloroethylene (TCE)-contaminated environment under a constant hydraulic gradient. Inverted resistivity tomograms are able to track the evolution of the permanganate plume in agreement with visual observations made on the side of the tank. Self-potential measurements were also performed at the surface of the sandbox using non-polarizing Ag-AgCl electrodes. These data were inverted to obtain the source density distribution with and without the resistivity information. A compact horizontal dipole source located at the front of the plume was obtained from the inversion of these self-potential data. This current dipole may be related to the redox reaction occurring between TCE and permanganate and the strong concentration gradient at the front of the plume. We demonstrate that time-lapse self-potential signals can be used to track the kinetics of an advecting oxidizer plume with acceptable accuracy and, if needed, in real time, but are unable to completely resolve the shape of the plume. In the field investigation, a 3D resistivity tomography is used to characterize an organic contaminant plume (resistive domain) and an overlying zone of solid waste materials (conductive domain). After removing the influence of the streaming potential, the identified source current density had a magnitude of 0.5 A m-2. The strong source current density may be attributed to charge movement between the neighboring zones that encourage abiotic and microbially enhanced reduction and oxidation reactions. In both cases, the self-potential source current density is located in the area of strong resistivity

Enviromnental contamination during a vancomycin-resistant Enterococci outbreak at a hospital in Argentina

OpenAIRE

Zarate, Mariela Soledad; Gales, Ana [UNIFESP; Jordd-Vargas, L'fiana; Yahni, Diego; RelloSo, Silvia; Bonvehi, Pablo; Monteiro, Jussimara [UNIFESP; Campos-Pignatari, Antonio [UNIFESP; Smayevsky, Jorgelina [UNIFESP

2007-01-01

INTRODUCTION. Vancomycin-resistant enterococci isolates (VRE) have caused numerous outbreaks in intensive care units (ICUs). A contaminated hospital environment, the hands of health care workers (HCW), and carrier patients may play important roles in perpetuating the chain of transmission in these outbreaks. the aims of this study were to report the first VRE outbreak in our center and assess the role of environmental contamination and HCW hands in the spread of new cases of enterococcal infe...

Contamination of the Clinical Microbiology Laboratory with Vancomycin-Resistant Enterococci and Multidrug- Resistant Enterobacteriaceae: Implications for Hospital and Laboratory Workers

Science.gov (United States)

Collins, Susan M.; Hacek, Donna M.; Degen, Lisa A.; Wright, Marc O.; Noskin, Gary A.; Peterson, Lance R.

2001-01-01

We surveyed environmental surfaces in our clinical microbiology laboratory to determine the prevalence of vancomycin-resistant enterococci (VRE) and multidrug-resistant Enterobacteriaceae (MDRE) during a routine working day. From a total of 193 surfaces, VRE were present on 20 (10%) and MDRE were present on 4 (2%) of the surfaces tested. In a subsequent survey after routine cleaning, all of the 24 prior positive surfaces were found to be negative. Thus, those in the laboratory should recognize that many surfaces may be contaminated by resistant organisms during routine processing of patient specimens. PMID:11574615

Metal resistant plants and phytoremediation of environmental contamination

Science.gov (United States)

Meagher, Richard B.; Li, Yujing; Dhankher, Om P.

2010-04-20

The present disclosure provides a method of producing transgenic plants which are resistant to at least one metal ion by transforming the plant with a recombinant DNA comprising a nucleic acid encoding a bacterial arsenic reductase under the control of a plant expressible promoter, and a nucleic acid encoding a nucleotide sequence encoding a phytochelatin biosynthetic enzyme under the control of a plant expressible promoter. The invention also relates a method of phytoremediation of a contaminated site by growing in the site a transgenic plant expressing a nucleic acid encoding a bacterial arsenate reductase and a nucleic acid encoding a phytochelatin biosynthetic enzyme.

An approach to delineate the contaminated groundwater in landfill based on Electrical Resistivity Imaging Technique

International Nuclear Information System (INIS)

Nor Dalila Desa; Lakam Mejus; Mohd Tadza Abdul Rahman; Kamarudin Samuding; Roslanzairi Mostapa; Mod Omar Hassan

2010-01-01

Full text: The occurrence of contaminated groundwater can often be recognized by a decrease in formation of resistivity values, since the latter is primarily dependent on the resistivity of the pore water. Landfills can be considered as one of major source of contamination that contributes to air, land and water pollution. Landfills are supposed to have a protective bottom layer (barrier layer) to prevent contaminants from getting into the groundwater that exist almost everywhere underground. However, if there is no layer or if it is cracked, water percolating through landfills produces leachate can make their way down into the groundwater system. In geophysical studies, the various properties of materials on earth are known as the anomaly of the Earth's sub surface. It is important to understand which physical properties are associated with, and effective for, a particular target and geophysical method. This paper reviews the needs of geophysical field for mapping subsurface geology and features occurance. Electrical Resistivity Imaging (ERI) technique has been chosen for it has become one of the promising methods in order to obtain preliminary information of subsurface variance materials based on their physical properties. (author)

Evaluation of maize inbred lines for resistance to pre-harvest aflatoxin and fumonisin contamination in the field

Science.gov (United States)

Two important mycotoxins, aflatoxin and fumonisin, are among the most potent naturally occurring carcinogens, contaminating maize (Zea mays L.) and affecting the crop yield and quality. Resistance of maize to pre-harvest mycotoxin contamination, specifically aflatoxin produced by Aspergillus flavus ...

Study on contamination of sheep meat in Shahrekord area with Listeria ivanovii and determination its antibiotic resistance pattern

Directory of Open Access Journals (Sweden)

Farid Khalili Borujeni

2013-06-01

Full Text Available Background and objectives: Listeria monocytogenes and Listeria ivanovii are two pathogenic species of Listeria. The role of Listeria ivanovii is important in abortion, stillbirth, septicemia in animals and this bacterium sometimes is pathogenic in humans. Contamination of ovine carcasses during the slaughter and processing can cause foodborne infections in humans. In this study we examined the contamination of sheep meat in slaughter house of Shahrekord city to Listeria ivanovii and determined its antibiotic resistance pattern.Material and Methods: A total 200 samples of sheep meat were collected from abattoir and processed by use of two enrichment method. After doing specific biochemical tests and PCR, Listeria spp was identified and antibiotic resistance of isolated Listeria were tested by the agar disc diffusion method. Results: The contamination of sheep carcasses with listeria was 2.5% (5 out of 200 samples. All five isolates (2.5% were recognized as Listeria ivanovii and were resistant to four antibiotics, sensitive to six antibiotics and intermediate to other antibiotics.  Conclusion: According to the contamination rate in sheep carcasses with Listeria ivanovii and the relatively high antibiotic resistance specified in this bacteria, the role of red meat in transmission of Listeria spp. and appropriate use of antibiotics against this bacteria should be considered.

Impact of Some Ecological Factors on Fecal Contamination of Drinking Water by Diarrheagenic Antibiotic-Resistant Escherichia coli in Zagazig City, Egypt

Directory of Open Access Journals (Sweden)

Ahmed Elsadek Fakhr

2016-01-01

Full Text Available Fecal contamination of drinking water is a major health problem which accounts for many cases of diarrhea mainly in infants and foreigners. This contamination is a complex interaction of many parameters. Antibiotic resistance among bacterial isolates complicates the problem. The study was done to identify fecal contamination of drinking water by Diarrheagenic Antibiotic-Resistant Escherichia coli in Zagazig city and to trace reasons for such contamination, three hundred potable water samples were investigated for E. coli existence. Locations of E. coli positive samples were investigated in relation to population density, water source, and type of water pipe. Sixteen E. coli strains were isolated. Antibiotic sensitivity was done and enterotoxigenic, enteropathogenic, and enterohaemorrhagic virulence genes were investigated by PCR. Probability of fecal contamination correlated with higher population density, with increased distance from Zagazig water plant, and with asbestos cement water pipes. Resistance to at least one antimicrobial drug was found in all isolates. Virulence genes were detected in a rate of 26.27%, 13.13%, 20%, 6.67%, and 33.33% for LT, ST, stx1, stx2, and eae genes, respectively. This relatively high frequency of fecal contamination points towards the high risk of developing diarrhea by antibiotic resistant DEC in low socioeconomic communities particularly with old fashion distribution systems.

Milk contamination and resistance to processing conditions determine the fate of Lactococcus lactis bacteriophages in dairies.

Science.gov (United States)

Madera, Carmen; Monjardín, Cristina; Suárez, Juan E

2004-12-01

Milk contamination by phages, the susceptibility of the phages to pasteurization, and the high levels of resistance to phage infection of starter strains condition the evolution dynamics of phage populations in dairy environments. Approximately 10% (83 of 900) of raw milk samples contained phages of the quasi-species c2 (72%), 936 (24%), and P335 (4%). However, 936 phages were isolated from 20 of 24 (85%) whey samples, while c2 was detected in only one (4%) of these samples. This switch may have been due to the higher susceptibility of c2 to pasteurization (936-like phages were found to be approximately 35 times more resistant than c2 strains to treatment of contaminated milk in a plate heat exchanger at 72 degrees C for 15 s). The restriction patterns of 936-like phages isolated from milk and whey were different, indicating that survival to pasteurization does not result in direct contamination of the dairy environment. The main alternative source of phages (commercial bacterial starters) does not appear to significantly contribute to phage contamination. Twenty-four strains isolated from nine starter formulations were generally resistant to phage infection, and very small progeny were generated upon induction of the lytic cycle of resident prophages. Thus, we postulate that a continuous supply of contaminated milk, followed by pasteurization, creates a factory environment rich in diverse 936 phage strains. This equilibrium would be broken if a particular starter strain turned out to be susceptible to infection by one of these 936-like phages, which, as a consequence, became prevalent.

Degradation Capability of n-hexadecane Degrading Bacteria from Petroleum Contaminated Soils

Directory of Open Access Journals (Sweden)

PENG Huai-li

2017-05-01

Full Text Available Samplings were performed in the petroleum contaminated soils of Dongying, Shandong Province of China. Degrading bacteria was isolated through enrichment in a Bushnel-Hass medium, with n-hexadecane as the sole source of carbon and energy. Then the isolated strains were identified by amplification of 16S rDNA gene and sequencing. The strain TZSX2 was selected as the powerful bacteria with stronger degradation ability, which was then identified as Rhodococcus hoagii genera based on the constructing results of the phylogenetic tree. The optimum temperature that allowed both high growth and efficient degradation ratio was in the scope of 28~36 ℃, and gas chromatography results showed that approximately more than 30% of n-hexadecane could be degraded in one week of incubation within the temperature range. Moreover, the strain TZSX2 was able to grow in high concentrations of n-hexadecane. The degradation rate reached 79% when the initial n-hexadecane concentration was 2 mL·L-1,while it still achieved 12% with n-hexadecane concentration of 20 mL·L-1. The optimal pH was 9 that allowed the highest growth and the greatest degradation rate of 91%. Above all, the screened strain TZSX2 showed high capabilities of alkali tolerance with excellent degradation efficiency for even high concentration of n-hexadecane, and thus it would be quite suitable for the remediation of petroleum contaminated soils especially in the extreme environment.

Frequent Multidrug-Resistant Acinetobacter baumannii Contamination of Gloves, Gowns, and Hands of Healthcare Workers

Science.gov (United States)

Morgan, Daniel J.; Liang, Stephen Y.; Smith, Catherine L.; Johnson, J. Kristie; Harris, Anthony D.; Furuno, Jon P.; Thom, Kerri A.; Snyder, Graham M.; Day, Hannah R.; Perencevich, Eli N.

2010-01-01

BACKGROUND Multidrug-resistant (MDR) gram-negative bacilli are important nosocomial pathogens. OBJECTIVE To determine the incidence of transmission of MDR Acinetobacter baumannii and Pseudomonas aeruginosa from patients to healthcare workers (HCWs) during routine patient care. DESIGN Prospective cohort study. SETTING Medical and surgical intensive care units. METHODS We observed HCWs who entered the rooms of patients colonized with MDR A. baumannii or colonized with both MDR A. baumannii and MDR P. aeruginosa. We examined their hands before room entry, their disposable gloves and/or gowns upon completion of patient care, and their hands after removal of gloves and/or gowns and before hand hygiene. RESULTS Sixty-five interactions occurred with patients colonized with MDR A. baumannii and 134 with patients colonized with both MDR A. baumannii and MDR P. aeruginosa. Of 199 interactions between HCWs and patients colonized with MDR A. baumannii, 77 (38.7% [95% confidence interval {CI}, 31.9%–45.5%]) resulted in HCW contamination of gloves and/or gowns, and 9 (4.5% [95% CI, 1.6%–7.4%]) resulted in contamination of HCW hands after glove removal before hand hygiene. Of 134 interactions with patients colonized with MDR P. aeruginosa, 11 (8.2% [95% CI, 3.6%–12.9%]) resulted in HCW contamination of gloves and/or gowns, and 1 resulted in HCW contamination of hands. Independent risk factors for contamination with MDR A. baumannii were manipulation of wound dressing (adjusted odds ratio [aOR], 25.9 [95% CI, 3.1–208.8]), manipulation of artificial airway (aOR, 2.1 [95% CI, 1.1–4.0]), time in room longer than 5 minutes (aOR, 4.3 [95% CI, 2.0–9.1]), being a physician or nurse practitioner (aOR, 7.4 [95% CI, 1.6–35.2]), and being a nurse (aOR, 2.3 [95% CI, 1.1–4.8]). CONCLUSIONS Gowns, gloves, and unwashed hands of HCWs were frequently contaminated with MDR A. baumannii. MDR A. baumannii appears to be more easily transmitted than MDR P. aeruginosa and perhaps more

Robustness and Radiation Resistance of the Pale Grass Blue Butterfly from Radioactively Contaminated Areas: A Possible Case of Adaptive Evolution.

Science.gov (United States)

Nohara, Chiyo; Hiyama, Atsuki; Taira, Wataru; Otaki, Joji M

2018-02-14

The pale grass blue butterfly, Zizeeria maha, has been used to evaluate biological impacts of the Fukushima nuclear accident in March 2011. Here, we examined the possibility that butterflies have adapted to be robust in the contaminated environment. Larvae (n = 2432) were obtained from adult butterflies (n = 20) collected from 7 localities with various contamination levels in May 2012, corresponding to the 7th generation after the accident. When the larvae were reared on non-contaminated host plant leaves from Okinawa, the normality rates of natural exposure without artificial irradiation (as an indication of robustness) were high not only in the least contaminated locality but also in the most contaminated localities. The normality rates were similarly obtained when the larvae were reared on non-contaminated leaves with external irradiation or on contaminated leaves from Fukushima to deliver internal irradiation. The normality rate of natural exposure and that of external or internal exposure were correlated, suggesting that radiation resistance (or susceptibility) likely reflects general state of health. The normality rate of external or internal exposure was divided by the relative normality rate of natural exposure, being defined as the resistance value. The resistance value was the highest in the populations of heavily contaminated localities and was inversely correlated with the distance from the Fukushima Dai-ichi nuclear power plant. These results suggest that the butterfly population might have adapted to the contaminated environment within approximately 1 year after the accident. The present study may partly explain the decrease in mortality and abnormality rates later observed in the contaminated areas. © The American Genetic Association 2017. All rights reserved. For permissions, please e-mail: journals.permissions@oup.com.

Evaluation of maize inbred lines for resistance to pre-harvest aflatoxin and fumonisin contamination in the field

Directory of Open Access Journals (Sweden)

Baozhu Guo

2017-06-01

Full Text Available Two important mycotoxins, aflatoxin and fumonisin, are among the most potent naturally occurring carcinogens, contaminating maize (Zea mays and affecting crop yield and quality. Resistance of maize to pre-harvest mycotoxin contamination, specifically aflatoxin produced by Aspergillus flavus and fumonisin produced by Fusarium verticillioides, is a goal in breeding programs that screen for these important traits with the aim of developing resistant commercial hybrids. We conducted two years of field evaluations on 87 inbred lines originating primarily in China and Mexico and not previously screened for resistance. The objectives of our study were to identify resistant germplasm for breeding purposes and to examine possible relationships between resistances to the two mycotoxins. Aflatoxin and fumonisin were present in samples harvested from all lines in both years. Concentrations of total aflatoxin ranged from 52.00 ± 20.00 to 1524.00 ± 396.00 μg kg−1, while those of fumonisin ranged from 0.60 ± 0.06 to 124.00 ± 19.50 mg kg−1. The inbred lines TUN15, TUN61, TUN37, CY2, and TUN49 showed the lowest aflatoxin accumulation and CN1, GT601, TUN09, TUN61, and MP717 the lowest fumonisin accumulation. TUN61 showed the lowest accumulation of both mycotoxins. This study confirmed previous observations that high levels of aflatoxin can coexist with fumonisin, with 55 maize lines showing a positive correlation coefficient between the concentrations of aflatoxin and fumonisin and 32 lines showing a negative correlation coefficient. These selected lines, particularly TUN61, may provide sources of resistance to mycotoxin contamination in breeding programs. However, the mechanism of resistance in this germplasm remains to be identified. Future research should also address factors that influence the fungus–plant interaction, such as herbivory and environmental stress.

SRNL EMERGENCY RESPONSE CAPABILITY FOR ATMOSPHERIC CONTAMINANT RELEASES

International Nuclear Information System (INIS)

Koffman, L; Chuck Hunter, C; Robert Buckley, R; Robert Addis, R

2006-01-01

Emergency response to an atmospheric release of chemical or radiological contamination is enhanced when plume predictions, field measurements, and real-time weather information are integrated into a geospatial framework. The Weather Information and Display (WIND) System at Savannah River National Laboratory (SRNL) utilizes such an integrated framework. The rapid availability of predictions from a suite of atmospheric transport models within this geospatial framework has proven to be of great value to decision makers during an emergency involving an atmospheric contaminant release

Public health implications of contamination of Franc CFA (XAF) circulating in Buea (Cameroon) with drug resistant pathogens.

Science.gov (United States)

Akoachere, Jane-Francis Tatah Kihla; Gaelle, Nana; Dilonga, Henry Meriki; Nkuo-Akenji, Theresa K

2014-01-08

Studies in different parts of the world have implicated money as a vehicle for transmission of pathogens. Such information which is necessary to facilitate infection control strategies is lacking in many sub-Saharan countries including Cameroon. This study analyzed the Franc de la Communauté Financiere d'Afrique (Franc CFA), the currency used in Cameroon and other countries in the Central African sub-region, as a potential vehicle for transmission of pathogenic bacteria and fungi, particularly drug-resistant strains, to generate findings which could create awareness on currency contamination and serve as a guide when formulating health policies on currency. Two hundred and thirteen currency samples representing various denominations of notes and coins randomly collected from diverse sources in Buea, Cameroon were analyzed for bacteria and fungi. The sensitivity of bacterial isolates to antibiotics was tested using the disc diffusion method. The relationship between contamination and physical state, source or denomination of currency was assessed using the χ2 test. All statistics were discussed at 0.05 significance level. Two hundred (93.9%) samples were contaminated with notes (96.6%) showing higher contamination than coins (88.2%). Uncirculated (mint) samples showed no contamination. There was a significant difference (PCFA franc circulating in Buea could serve as a vehicle for transmission of drug resistant pathogenic or potential organisms and contamination could be due to currency usage and handling as mint notes were not contaminated. Hygiene practices during or after handling currency is greatly encouraged to prevent infection.

Time-lapse electrical resistivity anomalies due to contaminant transport around landfills

Directory of Open Access Journals (Sweden)

J. Yang

2007-06-01

Full Text Available The extent of landfill leachate can be delineated by geo-electrical imaging as a response to the varying electrical resistivity in the contaminated area. This research was based on a combination of hydrogeological numerical simulation followed by geophysical forward and inversion modeling performed to evaluate the migration of a contaminant plume from a landfill. As a first step, groundwater flow and contaminant transport was simulated using the finite elements numerical modeling software FEFLOW. The extent of the contaminant plume was acquired through a hydrogeological model depicting the distributions of leachate concentration in the system. Next, based on the empirical relationship between the concentration and electrical conductivity of the leachate in the porous media, the corresponding geo-electrical structure was derived from the hydrogeological model. Finally, forward and inversion computations of geo-electrical anomalies were performed using the finite difference numerical modeling software DCIP2D/DCIP3D. The image obtained by geophysical inversion of the electric data was expected to be consistent with the initial hydrogeological model, as described by the distribution of leachate concentration. Numerical case studies were conducted for various geological conditions, hydraulic parameters and electrode arrays, from which conclusions were drawn regarding the suitability of the methodology to assess simple to more complex geo-electrical models. Thus, optimal mapping and monitoring configurations were determined.

Resistance of Pseudomonas aeruginosa to liquid disinfectants on contaminated surfaces before formation of biofilms.

Science.gov (United States)

Sagripanti, J L; Bonifacino, A

2000-01-01

A comparison was made of the effectiveness of popular disinfectants (Cavicide, Cidexplus, Clorox, Exspor, Lysol, Renalin, and Wavicide) under conditions prescribed for disinfection in the respective product labels on Pseudomonas aeruginosa either in suspension or deposited onto surfaces of metallic or polymeric plastic devices. The testing also included 7 nonformulated germicidal agents (glutaraldehyde, formaldehyde, peracetic acid, hydrogen peroxide, sodium hypochlorite, phenol, and cupric ascorbate) commonly used in disinfection and decontamination. Results showed that P. aeruginosa is on average 300-fold more resistant when present on contaminated surfaces than in suspension. This increase in resistance agrees with results reported in studies of biofilms, but unexpectedly, it precedes biofilm formation. The surface to which bacteria are attached can influence the effectiveness of disinfectants. Viable bacteria attached to devices may require dislodging through more than a one-step method for detection. The data, obtained with a sensitive and quantitative test, suggest that disinfectants are less effective on contaminated surfaces than generally acknowledged.

A molecular epidemiological study of methicillin-resistant Staphylococci environmental contamination in railway stations and coach stations in Guangzhou of China.

Science.gov (United States)

Lin, J L; Peng, Y; Ou, Q T; Lin, D X; Li, Y; Ye, X H; Zhou, J L; Yao, Z J

2017-02-01

Methicillin-resistant Staphylococcus aureus (MRSA) has caused a series of public health problems since it was first found in 1961. However, there are few research studies on the MRSA environmental contamination in railway stations and coach stations. Therefore, the aim of this study was to determine MRSA environmental contamination in public transport stations. Between December 2013 and January 2014, 380 surface samples from three railway stations (180) and four coach stations (200) in Guangzhou were collected to isolate and determine the prevalence and characteristics of Staphylococci strains. 39·21% of all samples were Staphylococci isolates, 1·58% of Staphylococci isolates were MRSA isolates, and 6·05% were methicillin-susceptible S. aureus. The proportion of multidrug resistant among 149 Staphylococci isolates was 75·84%. None of MRSA isolates was identified with the Panton-Valentine Leukocidin (PVL) genes, and one of them was identified with the qac gene. Four MRSA isolates were Staphylococcal Cassette Chromosome mec IVa, and the other two were nontypeable. Staphylococcus aureus isolates were classified into several sequence types (STs), and STs showed possible cross-transmissions of isolates from various sources. Methicillin-resistant Staphylococci contamination prevalence was high, and the environment of stations may be the vectors transmitting the Staphylococci to passengers. This is the first study to comprehensively report the prevalence, antibiotic resistance, and molecular characteristics of contamination of Staphylococci isolates in railway stations and coach stations of China. It will have great public health implications on infection control in community settings because of the serious hazard of Staphylococci, especially methicillin-resistant Staphylococci. Our findings have provided evidence for relevant departments to reduce the contamination of Staphylococci in environment of public transport stations. © 2016 The Society for Applied

Resistivity profiling for mapping gravel layers that may control contaminant migration at the Amargosa Desert Research Site, Nevada

Science.gov (United States)

Lucius, Jeffrey E.; Abraham, Jared D.; Burton, Bethany L.

2008-01-01

Gaseous contaminants, including CFC 113, chloroform, and tritiated compounds, move preferentially in unsaturated subsurface gravel layers away from disposal trenches at a closed low-level radioactive waste-disposal facility in the Amargosa Desert about 17 kilometers south of Beatty, Nevada. Two distinct gravel layers are involved in contaminant transport: a thin, shallow layer between about 0.5 and 2.2 meters below the surface and a layer of variable thickness between about 15 and 30 meters below land surface. From 2003 to 2005, the U.S. Geological Survey used multielectrode DC and AC resistivity surveys to map these gravel layers. Previous core sampling indicates the fine-grained sediments generally have higher water content than the gravel layers or the sediments near the surface. The relatively higher electrical resistivity of the dry gravel layers, compared to that of the surrounding finer sediments, makes the gravel readily mappable using electrical resistivity profiling. The upper gravel layer is not easily distinguished from the very dry, fine-grained deposits at the surface. Two-dimensional resistivity models, however, clearly identify the resistive lower gravel layer, which is continuous near the facility except to the southeast. Multielectrode resistivity surveys provide a practical noninvasive method to image hydrogeologic features in the arid environment of the Amargosa Desert.

Microbial Functional Gene Diversity Predicts Groundwater Contamination and Ecosystem Functioning

Science.gov (United States)

Zhang, Ping; Wu, Linwei; Rocha, Andrea M.; Shi, Zhou; Wu, Bo; Qin, Yujia; Wang, Jianjun; Yan, Qingyun; Curtis, Daniel; Ning, Daliang; Van Nostrand, Joy D.; Wu, Liyou; Watson, David B.; Adams, Michael W. W.; Alm, Eric J.; Adams, Paul D.; Arkin, Adam P.

2018-01-01

ABSTRACT Contamination from anthropogenic activities has significantly impacted Earth’s biosphere. However, knowledge about how environmental contamination affects the biodiversity of groundwater microbiomes and ecosystem functioning remains very limited. Here, we used a comprehensive functional gene array to analyze groundwater microbiomes from 69 wells at the Oak Ridge Field Research Center (Oak Ridge, TN), representing a wide pH range and uranium, nitrate, and other contaminants. We hypothesized that the functional diversity of groundwater microbiomes would decrease as environmental contamination (e.g., uranium or nitrate) increased or at low or high pH, while some specific populations capable of utilizing or resistant to those contaminants would increase, and thus, such key microbial functional genes and/or populations could be used to predict groundwater contamination and ecosystem functioning. Our results indicated that functional richness/diversity decreased as uranium (but not nitrate) increased in groundwater. In addition, about 5.9% of specific key functional populations targeted by a comprehensive functional gene array (GeoChip 5) increased significantly (P contamination and ecosystem functioning. This study indicates great potential for using microbial functional genes to predict environmental contamination and ecosystem functioning. PMID:29463661

Isolation, screening and identification of mercury resistant bacteria from mercury contaminated soil

OpenAIRE

Kowalczyk Anna; Wilińska Magdalena; Chyc Marek; Bojko Monika; Latowski Dariusz

2016-01-01

New bacterial strains resistant to high concentration of mercury were obtained and character iz ed focusing on their potential application in bioremediation. The biological material was isolated from soil contaminated with mercury. The ability to removal of Hg from the liquid medium and the effect of the various pH and mercury concentrations in the environment on bacterial strains growth kinetics were tested. The selected strains were identified by analysis of the 16S ribosome subunit coding ...

Evaluation of carriage and environmental contamination by carbapenem-resistant Acinetobacter baumannii.

Science.gov (United States)

Nutman, A; Lerner, A; Schwartz, D; Carmeli, Y

2016-11-01

We evaluated the sensitivity of surveillance cultures for carbapenem-resistant Acinetobacter baumannii (CRAB) in patients and in their environment. Patients with a CRAB-positive clinical culture were sampled within 7 days; the buccal mucosa and rectum were sampled using swabs, and skin was sampled using pre-moistened sterile sponges. Sponges were also used to sample the surrounding environment. Specimens were inoculated onto CHROMagar MDR Acinetobacter plates both directly and after overnight enrichment. CRAB load was scored semi-quantitatively and composite scores for patient colonization and environmental contamination were calculated. Thirty-four patients were included. Screening sensitivity was 28/34 (82%) for buccal mucosa, 30/34 (88%) for skin, and 25/34 (74%) for rectum. Combined sensitivity was 32/34 (94%). Among patients with CRAB-positive respiratory cultures, sensitivity for buccal mucosa was 20/20 (100%). Direct inoculation had excellent sensitivity: 25/28 (89%) for all three sites combined. In the subgroup of patients who did not have a respiratory source for CRAB, direct inoculation sensitivity was lower than among patients with CRAB-positive respiratory cultures: 5/8 (63%) versus 20/20 (100%). The environment of all patients was contaminated with CRAB. There was a positive correlation between the patient colonization score and the environmental contamination score (r = 0.63, p Environmental contamination is common and can be monitored. Implementing screening may facilitate infection control efforts to limit the spread of CRAB. Copyright © 2016 European Society of Clinical Microbiology and Infectious Diseases. Published by Elsevier Ltd. All rights reserved.

Laboratory Study of Quaternary Sediment Resistivity Related to Groundwater Contamination at Mae-Hia Landfill, Mueang District, Chiang Mai Province

Science.gov (United States)

Sichan, N.

2007-12-01

This study was aimed to understand the nature of the resistivity value of the sediment when it is contaminated, in order to use the information solving the obscure interpretation in the field. The pilot laboratory experiments were designed to simulate various degree of contamination and degree of saturation then observe the resulting changes in resistivity. The study was expected to get a better understanding of how various physical parameters effect the resistivity values in term of mathematic function. And also expected to apply those obtained function to a practical quantitatively interpretation. The sediment underlying the Mae-Hia Landfill consists of clay-rich material, with interfingerings of colluvium and sandy alluvium. A systematic study identified four kinds of sediment, sand, clayey sand, sandy clay, and clay. Representative sediment and leachate samples were taken from the field and returned to the laboratory. Both the physical and chemical properties of the sediments and leachate were analyzed to delineate the necessary parameters that could be used in Archie's equation. Sediment samples were mixed with various concentration of leachate solutions. Then the resistivity values were measured at various controlled steps in the saturation degree in a well- calibrated six-electrode model resistivity box. The measured resistivity values for sand, clayey sand, sandy clay when fully and partly saturated were collected, then plotted and fitted to Archie's equation, to obtain a mathematical relationship between bulk resistivity, porosity, saturation degree and resistivity of pore fluid. The results fit well to Archie's equation, and it was possible to determine all the unknown parameters representative of the sediment samples. For sand, clayey sand, sandy clay, and clay, the formation resistivity factors (F) are 2.90, 5.77, 7.85, and 7.85 with the products of cementation factor (m) and the pore geometry factors (a) (in term of -am) are 1.49, -1.63, -1.92, -2

Microbial Functional Gene Diversity Predicts Groundwater Contamination and Ecosystem Functioning

Directory of Open Access Journals (Sweden)

Zhili He

2018-02-01

Full Text Available Contamination from anthropogenic activities has significantly impacted Earth’s biosphere. However, knowledge about how environmental contamination affects the biodiversity of groundwater microbiomes and ecosystem functioning remains very limited. Here, we used a comprehensive functional gene array to analyze groundwater microbiomes from 69 wells at the Oak Ridge Field Research Center (Oak Ridge, TN, representing a wide pH range and uranium, nitrate, and other contaminants. We hypothesized that the functional diversity of groundwater microbiomes would decrease as environmental contamination (e.g., uranium or nitrate increased or at low or high pH, while some specific populations capable of utilizing or resistant to those contaminants would increase, and thus, such key microbial functional genes and/or populations could be used to predict groundwater contamination and ecosystem functioning. Our results indicated that functional richness/diversity decreased as uranium (but not nitrate increased in groundwater. In addition, about 5.9% of specific key functional populations targeted by a comprehensive functional gene array (GeoChip 5 increased significantly (P < 0.05 as uranium or nitrate increased, and their changes could be used to successfully predict uranium and nitrate contamination and ecosystem functioning. This study indicates great potential for using microbial functional genes to predict environmental contamination and ecosystem functioning.

Long-term electrical resistivity monitoring of recharge-induced contaminant plume behavior.

Science.gov (United States)

Gasperikova, Erika; Hubbard, Susan S; Watson, David B; Baker, Gregory S; Peterson, John E; Kowalsky, Michael B; Smith, Meagan; Brooks, Scott

2012-11-01

Geophysical measurements, and electrical resistivity tomography (ERT) data in particular, are sensitive to properties that are related (directly or indirectly) to hydrological processes. The challenge is in extracting information from geophysical data at a relevant scale that can be used to gain insight about subsurface behavior and to parameterize or validate flow and transport models. Here, we consider the use of ERT data for examining the impact of recharge on subsurface contamination at the S-3 ponds of the Oak Ridge Integrated Field Research Challenge (IFRC) site in Tennessee. A large dataset of time-lapse cross-well and surface ERT data, collected at the site over a period of 12 months, is used to study time variations in resistivity due to changes in total dissolved solids (primarily nitrate). The electrical resistivity distributions recovered from cross-well and surface ERT data agrees well, and both of these datasets can be used to interpret spatiotemporal variations in subsurface nitrate concentrations due to rainfall, although the sensitivity of the electrical resistivity response to dilution varies with nitrate concentration. Using the time-lapse surface ERT data interpreted in terms of nitrate concentrations, we find that the subsurface nitrate concentration at this site varies as a function of spatial position, episodic heavy rainstorms (versus seasonal and annual fluctuations), and antecedent rainfall history. These results suggest that the surface ERT monitoring approach is potentially useful for examining subsurface plume responses to recharge over field-relevant scales. Published by Elsevier B.V.

Expression Analysis of Stress-Related Genes in Kernels of Different Maize (Zea mays L.) Inbred Lines with Different Resistance to Aflatoxin Contamination

Science.gov (United States)

Jiang, Tingbo; Zhou, Boru; Luo, Meng; Abbas, Hamed K.; Kemerait, Robert; Lee, Robert Dewey; Scully, Brian T.; Guo, Baozhu

2011-01-01

This research examined the expression patterns of 94 stress-related genes in seven maize inbred lines with differential expressions of resistance to aflatoxin contamination. The objective was to develop a set of genes/probes associated with resistance to A. flavus and/or aflatoxin contamination. Ninety four genes were selected from previous gene expression studies with abiotic stress to test the differential expression in maize lines, A638, B73, Lo964, Lo1016, Mo17, Mp313E, and Tex6, using real-time RT-PCR. Based on the relative-expression levels, the seven maize inbred lines clustered into two different groups. One group included B73, Lo1016 and Mo17, which had higher levels of aflatoxin contamination and lower levels of overall gene expression. The second group which included Tex6, Mp313E, Lo964 and A638 had lower levels of aflatoxin contamination and higher overall levels of gene expressions. A total of six “cross-talking” genes were identified between the two groups, which are highly expressed in the resistant Group 2 but down-regulated in susceptible Group 1. When further subjected to drought stress, Tex6 expressed more genes up-regulated and B73 has fewer genes up-regulated. The transcript patterns and interactions measured in these experiments indicate that the resistant mechanism is an interconnected process involving many gene products and transcriptional regulators, as well as various host interactions with environmental factors, particularly, drought and high temperature. PMID:22069724

Mechanisms of friction and assessment of slip resistance of new and used footwear soles on contaminated floors.

Science.gov (United States)

Grönqvist, Raoul

1995-02-01

The great number of slipping accidents indicates that footwear providing good slip resistance must be rare. Slip resistance seems to be a purely physical phenomenon, however, more knowledge of the mechanisms of friction is needed to develop slip-resistant footwear and to ensure safer walking in slippery conditions. In the present study the influence of the normal wear of shoe heels and soles on their frictional properties was clarified. The slip resistance of three types of new and used safety shoes on four relatively slippery floor-contaminant combinations, was assessed with a prototype apparatus, which simulates the movements of a human foot and the forces applied to the underfoot surface during an actual slip. The used shoes were collected from 27 workers in a shipbuilding company and classified by sight into four wear classes: Good, satisfactory, poor, and worn-out. The assessed shoe heels and soles were in general more slippery when new compared to used heels and soles. However, footwear must be discarded before the tread pattern is worn-out. Used microcellular polyurethane (PU) heels and soles gave a considerably higher coefficient of kinetic friction (μ k ) on contaminated floors than used heels and soles made of compact nitrile (NR) and compact styrene rubber (SR). The heel-slide coefficient of kinetic friction (μ kl ) for used versus new shoes was on average 66% higher for PU (0·216 versus 0·130), 27% higher for SR (0·143 versus 0·113), and 7% lower for NR (0·098 versus 0·105). The fundamental mechanisms of friction between shoe soles and contaminated floors were also discussed, and experiments with seven slabs of sole materials were carried out to assess contact pressure effects from the viewpoint of slipping. Slip resistance particularly seemed to depend on the squeeze film and the contact pressure effects between the soling materials and the floor. An increasing contact pressure dramatically reduced the μ k , thus indicating that the slip

3D resistivity method to monitor degradation of an organic contaminant in sand boxes

Science.gov (United States)

Fernandez, P. M.; Bloem, E.; Philippe, R.; French, H. K.

2015-12-01

Degradation of organic chemicals under various saturation conditions is a process highly relevant to protect groundwater. The redox potential drives the degradation of organic compounds. Its variation affects the water chemistry, gas release and responses of the geo-electrical signature. This study explores how non-invasive measurements sensitive to geo-electrical properties provides quantitative information about the in-situ redox situation. During this presentation, the preliminary results of a laboratory experiment to study the degradation of deicing chemicals with 3D resistivity and self-potential techniques, water samples will be shown. The experiment consists of sand boxes (1.0x0.5x0.4 m) to which both sides of each box is contaminated with propylene glycol, an aircraft deicing fluid, commonly used in Norwegian airports. Each source is placed near the water table with static conditions. At one side a conductor is placed, linking the contamination zone at the water table and the unsaturated zone with a low water content, to improve the degradation by facilitating the electron exchange. At the other side, degradation occurs under natural conditions. Each box is equipped with 288 electrodes, distributed on six faces to perform 3D resistivity measurements. In addition to the resistivity, self-potential measurements are taken from the sand surface. Six water wells are installed above and below the water table to provide more information on the degradation processes. Moreover, measurements of carbon dioxide on the surface are performed as higher concentrations are expected where the pollutant is degraded.

Resistance to disinfection of a polymicrobial association contaminating the surface of elastomeric dental impressions.

Science.gov (United States)

Giammanco, Giovanni M; Melilli, Dario; Rallo, Antonio; Pecorella, Sonia; Mammina, Caterina; Pizzo, Giuseppe

2009-04-01

The aim of this study was to evaluate the ability to resist disinfection of a polymicrobial association contaminating the surface of dental impressions obtained with two different elastomers: a polyether (Impregum) and an addition-polymerized silicone (Elite). Impressions were contaminated with a mixture of three biofilm-forming microorganisms (Staphylococcus aureus, Pseudomonas aeruginosa and Candida albicans) and disinfected immediately after contamination, or after microbial layers were allowed to develop during a six-hour storage. Two commercial disinfectants were tested: MD 520 containing 0.5% glutaraldehyde and Sterigum Powder without glutaraldehyde. Residual contamination was recovered by mechanical rinsing immediately after disinfection and after a six-hour storage of disinfected impressions, and assessed by colony counting. Both disinfectants tested were shown to be effective in reducing the microbial presence on the impression materials, achieving at least a 102 reduction of microbial counts compared to water rinsing. However, Sterigum was generally less effective on the Elite elastomer and could not grant disinfection on six-hour aged P. aeruginosa and C. albicans microbial layers. The results of this study suggest that the materials used for the impressions influence the efficacy of disinfection. Disinfectants should be tested according to conditions encountered in everyday clinical practice and the need for immediate disinfection of impressions should be clearly indicated by manufacturers.

Isolation and characterization of Staphylococcus sp. strain NBRIEAG-8 from arsenic contaminated site of West Bengal

Energy Technology Data Exchange (ETDEWEB)

Srivastava, Shubhi; Singh, Namrata; Singh, Nandita [CSIR - National Botanical Research Institute, Lucknow, UP (India). Eco-auditing Lab.; Verma, Praveen C.; Singh, Ankit; Mishra, Manisha [CSIR - National Botanical Research Institute, Lucknow, UP (India). Plant Molecular Biology and Genetic Engineering; Sharma, Neeta [Lucknow Univ., UP (India). Plant Pathology Lab.

2012-09-15

Arsenic contaminated rhizospheric soils of West Bengal, India were sampled for arsenic resistant bacteria that could transform different arsenic forms. Staphylococcus sp. NBRIEAG-8 was identified by16S rDNA ribotyping, which was capable of growing at 30,000 mg l{sup -1} arsenate [As(V)] and 1,500 mg l{sup -1} arsenite [As(III)]. This bacterial strain was also characterized for arsenical resistance (ars) genes which may be associated with the high-level resistance in the ecosystems of As-contaminated areas. A comparative proteome analysis was conducted with this strain treated with 1,000 mg l{sup -1} As(V) to identify changes in their protein expression profiles. A 2D gel analysis showed a significant difference in the proteome of arsenic treated and untreated bacterial culture. The change in pH of cultivating growth medium, bacterial growth pattern (kinetics), and uptake of arsenic were also evaluated. After 72 h of incubation, the strain was capable of removing arsenic from the culture medium amended with arsenate and arsenite [12% from As(V) and 9% from As(III)]. The rate of biovolatilization of As(V) was 23% while As(III) was 26%, which was determined indirectly by estimating the sum of arsenic content in bacterial biomass and medium. This study demonstrates that the isolated strain, Staphylococcus sp., is capable for uptake and volatilization of arsenic by expressing ars genes and 8 new upregulated proteins which may have played an important role in reducing arsenic toxicity in bacterial cells and can be used in arsenic bioremediation. (orig.)

Mapping microbial ecosystems and spoilage-gene flow in breweries highlights patterns of contamination and resistance.

Science.gov (United States)

Bokulich, Nicholas A; Bergsveinson, Jordyn; Ziola, Barry; Mills, David A

2015-03-10

Distinct microbial ecosystems have evolved to meet the challenges of indoor environments, shaping the microbial communities that interact most with modern human activities. Microbial transmission in food-processing facilities has an enormous impact on the qualities and healthfulness of foods, beneficially or detrimentally interacting with food products. To explore modes of microbial transmission and spoilage-gene frequency in a commercial food-production scenario, we profiled hop-resistance gene frequencies and bacterial and fungal communities in a brewery. We employed a Bayesian approach for predicting routes of contamination, revealing critical control points for microbial management. Physically mapping microbial populations over time illustrates patterns of dispersal and identifies potential contaminant reservoirs within this environment. Habitual exposure to beer is associated with increased abundance of spoilage genes, predicting greater contamination risk. Elucidating the genetic landscapes of indoor environments poses important practical implications for food-production systems and these concepts are translatable to other built environments.

Geoelectrical mapping and groundwater contamination

Science.gov (United States)

Blum, Rainer

Specific electrical resistivity of near-surface materials is mainly controlled by the groundwater content and thus reacts extremely sensitive to any change in the ion content. Geoelectric mapping is a well-established, simple, and inexpensive technique for observing areal distributions of apparent specific electrical resistivities. These are a composite result of the true resistivities in the underground, and with some additional information the mapping of apparent resistivities can help to delineate low-resistivity groundwater contaminations, typically observed downstream from sanitary landfills and other waste sites. The presence of other good conductors close to the surface, mainly clays, is a serious noise source and has to be sorted out by supporting observations of conductivities in wells and geoelectric depth soundings. The method may be used to monitor the extent of groundwater contamination at a specific time as well as the change of a contamination plume with time, by carrying out repeated measurements. Examples for both are presented.

Hydrocarbon-degrading Capability of Bacteria isolated from a Maize ...

African Journals Online (AJOL)

Hydrocarbon-degrading Capability of Bacteria isolated from a Maize-Planted, Kerosene-contaminated Ilorin Alfisol. ... also revealed that some bacteria survive and even thrive in kerosene contaminated soil and hence have the potential to be used in biodegradation and/or bioremediation of oil contaminated soils and water.

Isolation and characterization of a biosurfactant-producing heavy metal resistant Rahnella sp. RM isolated from chromium-contaminated soil

OpenAIRE

GOVARTHANAN, Muthusamy; MYTHILI, R.; SELVANKUMAR, Thangasamy; KAMALA-KANNAN, S.; CHOI, DuBok; CHANG, Young-Cheol

2017-01-01

Objective of the study was to isolate heavy metal resistant bacteria from chromium-contaminated subsurface soil and investigate biosurfactant production and heavy metal bioremediation. Based on 16S rRNA gene sequence and phylogenetic analysis, the isolate was identified as Rahnella sp. RM. The biosurfactant production by heavy metal resistant Rahnella sp. RM was optimized using Box- Behnken design (BBD). The maximum emulsification activity was obtained 66% at 6% soybean meal in pH 7.0 and 33....

Enterobacter asburiae KUNi5, a Nickel Resistant Bacterium for Possible Bioremediation of Nickel Contaminated Sites.

Science.gov (United States)

Paul, Anirudha; Mukherjee, Samir Kumar

2016-01-01

Nickel resistant bacterial strain Enterobacter asburiae KUNi5 was isolated and showed resistance up to 15 mM and could remove Ni optimally better at 37 degrees C and pH 7. Maximum removal was found at initial concentration of 0.5 to 2 mM, however, growth and Ni removal were affected by other heavy metals. Major amount of the metal was accumulated in the membrane fractions and certain negatively charged groups were found responsible for Ni binding. KUNi5 could also produce 1-aminocyclopropane-1-carboxylate deaminase, indole-acetic acid and siderophore. It seems that KUNi5 could be a possible candidate for Ni detoxification and plant growth promotion in Ni-contaminated field.

Analysis of environmental contamination resulting from catastrophic incidents: part 2. Building laboratory capability by selecting and developing analytical methodologies.

Science.gov (United States)

Magnuson, Matthew; Campisano, Romy; Griggs, John; Fitz-James, Schatzi; Hall, Kathy; Mapp, Latisha; Mullins, Marissa; Nichols, Tonya; Shah, Sanjiv; Silvestri, Erin; Smith, Terry; Willison, Stuart; Ernst, Hiba

2014-11-01

Catastrophic incidents can generate a large number of samples of analytically diverse types, including forensic, clinical, environmental, food, and others. Environmental samples include water, wastewater, soil, air, urban building and infrastructure materials, and surface residue. Such samples may arise not only from contamination from the incident but also from the multitude of activities surrounding the response to the incident, including decontamination. This document summarizes a range of activities to help build laboratory capability in preparation for sample analysis following a catastrophic incident, including selection and development of fit-for-purpose analytical methods for chemical, biological, and radiological contaminants. Fit-for-purpose methods are those which have been selected to meet project specific data quality objectives. For example, methods could be fit for screening contamination in the early phases of investigation of contamination incidents because they are rapid and easily implemented, but those same methods may not be fit for the purpose of remediating the environment to acceptable levels when a more sensitive method is required. While the exact data quality objectives defining fitness-for-purpose can vary with each incident, a governing principle of the method selection and development process for environmental remediation and recovery is based on achieving high throughput while maintaining high quality analytical results. This paper illustrates the result of applying this principle, in the form of a compendium of analytical methods for contaminants of interest. The compendium is based on experience with actual incidents, where appropriate and available. This paper also discusses efforts aimed at adaptation of existing methods to increase fitness-for-purpose and development of innovative methods when necessary. The contaminants of interest are primarily those potentially released through catastrophes resulting from malicious activity

A Contaminant Trap as a Tool for Isolating and Measuring the Desorption Resistant Fraction of Soil Pollutants

DEFF Research Database (Denmark)

Mayer, Philipp; L. Olsen, Jannik; Gouliarmou, Varvara

2011-01-01

Bioremediation of contaminated soils often leaves a desorption-resistant pollutant fraction behind in the soil, which in the present study was isolated with a combination of diffusive carrier and infinite diffusive sink. Such a diffusive sink was made by casting a composite of silicone...... and activated carbon into the bottom of a large glass. Field-contaminated soil samples were then suspended in a cyclodextrin solution and incubated in such glasses for the continuous trapping of PAH molecules during their release from the soil matrix. The PAH concentrations remaining in the soil were determined...... by exhaustive extraction and compared with a biodegradation experiment. The concentration decline in the first soil was faster in the contaminant trap than in the biodegradation experiment, but the halting of the biodegradation process before reaching the legal threshold level was well indicated...

Enhanced Cadmium (Cd Phytoextraction from Contaminated Soil using Cd-Resistant Bacterium

Directory of Open Access Journals (Sweden)

Kunchaya Setkit

2014-01-01

Full Text Available A cadmium (Cd-resistant bacterium, Micrococcus sp. MU1, is able to produce indole-3-acetic acid and promotes root elongation and plant growth. The potential of this bacterium on enhancement of Cd uptake and bioaccumulation of Cd in Helianthus annuus L. planted in Cd-contaminated soil was evaluated in greenhouse condition. The results showed that Micrococcus sp. MU1promoted the growth of H. annuus L. by increasing the root length, stem height, dry biomass, root to shoot ratio and also significantly increased Cd accumulation in the root and above-ground tissues of H. annuus L. compared to uninoculated control. Re-inoculation with Micrococcus sp. MU1in contaminated soil helped in promoting plant growth and Cd phytoextraction throughout the cultivation period. In addition, phytoextraction coefficient and translocation factor (TF of H. annuus L. inoculated with Micrococcus sp. MU1were higher than that of uninoculated control and TF continuously increased with time. Our results suggested that Micrococcus sp. MU1 has an ability to enhance plant growth and Cd uptake in H. annuus L. Synergistic interaction between Micrococcus sp. MU1 and H. annuus L. could be further applied for Cd phytoextraction in polluted areas.

Effect of Surface Contaminants Remained on the Blasted Surface on Epoxy Coating Performance and Corrosion Resistance

International Nuclear Information System (INIS)

Baek, Kwang Ki; Park, Chung Seo; Kim, Ki Hong; Chung, Mong Kyu; Park, Jin Hwan

2006-01-01

One of the critical issues in the coating specification is the allowable limit of surface contaminant(s) - such as soluble salt(s), grit dust, and rust - after grit blasting. Yet, there is no universally accepted data supporting the relationship between the long-term coating performance and the amount of various surface contaminants allowed after grit blasting. In this study, it was attempted to prepare epoxy coatings applied on grit-blasted steel substrate dosed with controlled amount of surface contaminants - such as soluble salt(s), grit dust, and rust. Then, coating samples were subjected to 4,200 hours of cyclic test(NORSOK M-501), which were then evaluated in terms of resistance to rust creepage, blistering, chalking, rusting, cracking and adhesion strength. Additional investigations on the possible damage at the paint/steel interface were carried out using an Electrochemical Impedance Spectroscopy(EIS) and observations of under-film-corrosion. Test results suggested that the current industrial specifications were well matched with the allowable degree of rust, whereas the allowable amount of soluble salt and grit dust after grit blasting showed a certain deviation from the specifications currently employed for fabrication of marine vessels and offshore facilities

Isolation, screening and identification of mercury resistant bacteria from mercury contaminated soil

Directory of Open Access Journals (Sweden)

Kowalczyk Anna

2016-01-01

Full Text Available New bacterial strains resistant to high concentration of mercury were obtained and character iz ed focusing on their potential application in bioremediation. The biological material was isolated from soil contaminated with mercury. The ability to removal of Hg from the liquid medium and the effect of the various pH and mercury concentrations in the environment on bacterial strains growth kinetics were tested. The selected strains were identified by analysis of the 16S ribosome subunit coding sequenc es as Pseudomonas syringae. The analysis of Hg concentration in liquid medium as effect of microbial metabolism demonstrated that P. syringae is able to remove almost entire metal from medium after 120 hours of incubation. Obtained results revealed new ability of the isolated strain P. syringae. Analyzed properties of this soil bacteria species able to reduce concentration of Hg ors immobi lize this metal are promising for industrial wastewater treatment and bioremediation of the soils polluted especially by mercury lamps scrapping, measuring instruments, dry batteries, detonators or burning fuels made from crude oil, which may also contain mercury. Selected bacteria strains provide efficient and relatively low-cost bioremediation of the areas and waters contaminated with Hg.

Uranium biomineralization by a metal resistant Pseudomonas aeruginosa strain isolated from contaminated mine waste

Energy Technology Data Exchange (ETDEWEB)

Choudhary, Sangeeta [Department of Biotechnology, Indian Institute of Technology, Kharagpur 721302 (India); Sar, Pinaki, E-mail: sarpinaki@yahoo.com [Department of Biotechnology, Indian Institute of Technology, Kharagpur 721302 (India)

2011-02-15

Uranium biomineralization by a metal-resistant Pseudomonas aeruginosa strain isolated from uranium mine waste was characterized for its potential in bioremediation. Uranium resistance, its cellular localization and chemical nature of uranium-bacteria interaction were elucidated. Survival and uranium biomineralization from mine water were investigated using microcosm experiments. The selected bacterium showed U resistance and accumulation (maximum of 275 mg U g{sup -1} cell dry wt.) following incubation in 100 mg U L{sup -1}, pH 4.0, for 6 h. Transmission electron microscopy and X-ray diffraction analyses revealed that bioaccumulated uranium was deposited within the cell envelope as needle shaped U-phosphate compounds that attain crystallinity only at pH 4.0. A synergistic involvement of deprotonated phosphate and carboxyl moieties in facilitating bioprecipitation of uranium was evident from FTIR analysis. Based on these findings we attribute the localized U sequestration by this bacterium as innocuous complex to its possible mechanism of uranium resistance. Microcosm data confirmed that the strain can remove soluble uranium (99%) and sequester it as U oxide and phosphate minerals while maintaining its viability. The study showed that indigenous bacteria from contaminated site that can survive uranium and other heavy metal toxicity and sequester soluble uranium as biominerals could play important role in uranium bioremediation.

Nano-TiO2-based photocatalytic disinfection of environmental surfaces contaminated by meticillin-resistant Staphylococcus aureus.

Science.gov (United States)

Petti, S; Messano, G A

2016-05-01

Traditional cleaning and disinfection methods are inefficient for complete decontamination of hospital surfaces from meticillin-resistant Staphylococcus aureus (MRSA). Additional methods, such as nano-TiO2-based photocatalytic disinfection (PCD), could be helpful. To evaluate anti-MRSA activity of PCD on polyvinyl chloride (PVC) surfaces in natural-like conditions. Two identical PVC surfaces were used, and nano-TiO2 was incorporated into one of them. The surfaces were contaminated with MRSA isolated from hospitalized patients using a mist sprayer to simulate the mode of environmental contamination caused by a carrier. MRSA cell density was assessed before contamination until 180min after contamination using Rodac plates. The differences between test and control surfaces in terms of MRSA density and log MRSA density reduction were assessed using parametric and non-parametric statistical tests. Five strains were tested, and each strain was tested five times. The highest median MRSA densities [46.3 and 43.1 colony-forming units (cfu)/cm(2) for control and test surfaces, respectively] were detected 45min after contamination. Median MRSA densities 180min after contamination were 10.1 and 0.7cfu/cm(2) for control and test surfaces, respectively (Pdisinfectant activity remained stable throughout the 25 testing occasions, despite between-test cleaning and disinfection. The anti-MRSA activity of PCD was compatible with the benchmark for surface hygiene in hospitals (surfaces. However, for clinical surfaces, PCD should be regarded as supplemental to conventional decontamination procedures, rather than an alternative. Copyright © 2016 The Healthcare Infection Society. Published by Elsevier Ltd. All rights reserved.

Metal resistance mechanisms in Gram-negative bacteria and their potential to remove Hg in the presence of other metals.

Science.gov (United States)

Giovanella, Patricia; Cabral, Lucélia; Costa, Alexandre Pereira; de Oliveira Camargo, Flávio Anastácio; Gianello, Clesio; Bento, Fátima Menezes

2017-06-01

Contamination of the environment by heavy metals has been increasing in recent years due to industrial activities. Thus research involving microorganisms capable of surviving in multi-contaminated environments is extremely important. The objectives of the present study were to evaluate the removal of mercury alone and in the presence of cadmium, nickel and lead by four mercury-resistant microorganisms; estimate the removal of Cd, Ni and Pb; understand the mechanisms involved (reduction, siderophores, biofilms, biosorption and bioaccumulation) in the metal resistance of the isolate Pseudomonas sp. B50D; and determine the capacity of Pseudomonas sp. B50D in removing Hg, Cd, Ni and Pb from an industrial effluent. It was shown that the four isolates evaluated were capable of removing from 62% to 95% of mercury from a culture medium with no addition of other metals. The isolate Pseudomonas sp. B50D showed the best performance in the removal of mercury when evaluated concomitantly with other metals. This isolate was capable of removing 75% of Hg in the presence of Cd and 91% in the presence of Ni and Pb. With respect to the other metals it removed 60%, 15% and 85% of Cd, Ni and Pb, respectively. In tests with effluent, the isolate Pseudomonas sp. B50D removed 85% of Hg but did not remove the other metals. This isolate presented reduction, biosorption, biofilm production and siderophore production as its metal resistance mechanisms. Pseudomonas sp. B50D was thus a candidate with potential for application in the bioremediation of effluents with complex metal contaminations. Copyright © 2017 Elsevier Inc. All rights reserved.

Radiation resistances and decontamination of common pathogenic bacteria contaminated in white scar oyster (Crassostrea belcheri) in Thailand

Energy Technology Data Exchange (ETDEWEB)

Thupila, Nunticha [Department of Fishery Products, Faculty of Fisheries, Kasetsart University, 50 Ngamwongwan Rd. Ladyao, Chatuchak, Bangkok (Thailand); Ratana-arporn, Pattama, E-mail: ffispmr@ku.ac.t [Department of Fishery Products, Faculty of Fisheries, Kasetsart University, 50 Ngamwongwan Rd. Ladyao, Chatuchak, Bangkok (Thailand); Wilaipun, Pongtep [Department of Fishery Products, Faculty of Fisheries, Kasetsart University, 50 Ngamwongwan Rd. Ladyao, Chatuchak, Bangkok (Thailand)

2011-07-15

In Thailand, white scar oyster (Crassostrea belcheri) was ranked for premium quality, being most expensive and of high demand. This oyster is often eaten raw, hence it may pose health hazards to consumers when contaminated with food-borne pathogens. As limited alternative methods are available to sterilize the oyster while preserving the raw characteristic, irradiation may be considered as an effective method for decontamination. In this study, the radiation resistance of pathogenic bacteria commonly contaminating the oyster and the optimum irradiation doses for sterilization of the most radiation resistant bacteria were investigated. The radiation decimal reduction doses (D{sub 10}) of Salmonella Weltevreden DMST 33380, Vibrio parahaemolyticus ATCC 17802 and Vibrio vulnificus DMST 5852 were determined in broth culture and inoculated oyster homogenate. The D{sub 10} values of S. Weltevreden, V. parahaemolyticus and V. vulnificus in broth culture were 0.154, 0.132 and 0.059 kGy, while those of inoculated oyster homogenate were 0.330, 0.159 and 0.140 kGy, respectively. It was found that among the pathogens tested, S. Weltevreden was proved to be the most resistant species. An irradiation dose of 1.5 kGy reduced the counts of 10{sup 5} CFU/g S. Weltevreden inoculated in oyster meat to an undetectable level. The present study indicated that a low-dose irradiation can improve the microbial quality of oyster and further reduce the risks from the food-borne pathogens without adversely affecting the sensory attributes.

Radiation resistances and decontamination of common pathogenic bacteria contaminated in white scar oyster (Crassostrea belcheri) in Thailand

International Nuclear Information System (INIS)

Thupila, Nunticha; Ratana-arporn, Pattama; Wilaipun, Pongtep

2011-01-01

In Thailand, white scar oyster (Crassostrea belcheri) was ranked for premium quality, being most expensive and of high demand. This oyster is often eaten raw, hence it may pose health hazards to consumers when contaminated with food-borne pathogens. As limited alternative methods are available to sterilize the oyster while preserving the raw characteristic, irradiation may be considered as an effective method for decontamination. In this study, the radiation resistance of pathogenic bacteria commonly contaminating the oyster and the optimum irradiation doses for sterilization of the most radiation resistant bacteria were investigated. The radiation decimal reduction doses (D 10 ) of Salmonella Weltevreden DMST 33380, Vibrio parahaemolyticus ATCC 17802 and Vibrio vulnificus DMST 5852 were determined in broth culture and inoculated oyster homogenate. The D 10 values of S. Weltevreden, V. parahaemolyticus and V. vulnificus in broth culture were 0.154, 0.132 and 0.059 kGy, while those of inoculated oyster homogenate were 0.330, 0.159 and 0.140 kGy, respectively. It was found that among the pathogens tested, S. Weltevreden was proved to be the most resistant species. An irradiation dose of 1.5 kGy reduced the counts of 10 5 CFU/g S. Weltevreden inoculated in oyster meat to an undetectable level. The present study indicated that a low-dose irradiation can improve the microbial quality of oyster and further reduce the risks from the food-borne pathogens without adversely affecting the sensory attributes.

Radiation resistances and decontamination of common pathogenic bacteria contaminated in white scar oyster ( Crassostrea belcheri) in Thailand

Science.gov (United States)

Thupila, Nunticha; Ratana-arporn, Pattama; Wilaipun, Pongtep

2011-07-01

In Thailand, white scar oyster ( Crassostrea belcheri) was ranked for premium quality, being most expensive and of high demand. This oyster is often eaten raw, hence it may pose health hazards to consumers when contaminated with food-borne pathogens. As limited alternative methods are available to sterilize the oyster while preserving the raw characteristic, irradiation may be considered as an effective method for decontamination. In this study, the radiation resistance of pathogenic bacteria commonly contaminating the oyster and the optimum irradiation doses for sterilization of the most radiation resistant bacteria were investigated. The radiation decimal reduction doses ( D10) of Salmonella Weltevreden DMST 33380, Vibrio parahaemolyticus ATCC 17802 and Vibrio vulnificus DMST 5852 were determined in broth culture and inoculated oyster homogenate. The D10 values of S. Weltevreden, V. parahaemolyticus and V. vulnificus in broth culture were 0.154, 0.132 and 0.059 kGy, while those of inoculated oyster homogenate were 0.330, 0.159 and 0.140 kGy, respectively. It was found that among the pathogens tested, S. Weltevreden was proved to be the most resistant species. An irradiation dose of 1.5 kGy reduced the counts of 10 5 CFU/g S. Weltevreden inoculated in oyster meat to an undetectable level. The present study indicated that a low-dose irradiation can improve the microbial quality of oyster and further reduce the risks from the food-borne pathogens without adversely affecting the sensory attributes.

Uranium biomineralization by a metal resistant Pseudomonas aeruginosa strain isolated from contaminated mine waste.

Science.gov (United States)

Choudhary, Sangeeta; Sar, Pinaki

2011-02-15

Uranium biomineralization by a metal-resistant Pseudomonas aeruginosa strain isolated from uranium mine waste was characterized for its potential in bioremediation. Uranium resistance, its cellular localization and chemical nature of uranium-bacteria interaction were elucidated. Survival and uranium biomineralization from mine water were investigated using microcosm experiments. The selected bacterium showed U resistance and accumulation (maximum of 275 mg U g(-1)cell dry wt.) following incubation in 100 mg U L(-1), pH 4.0, for 6 h. Transmission electron microscopy and X-ray diffraction analyses revealed that bioaccumulated uranium was deposited within the cell envelope as needle shaped U-phosphate compounds that attain crystallinity only at pH 4.0. A synergistic involvement of deprotonated phosphate and carboxyl moieties in facilitating bioprecipitation of uranium was evident from FTIR analysis. Based on these findings we attribute the localized U sequestration by this bacterium as innocuous complex to its possible mechanism of uranium resistance. Microcosm data confirmed that the strain can remove soluble uranium (99%) and sequester it as U oxide and phosphate minerals while maintaining its viability. The study showed that indigenous bacteria from contaminated site that can survive uranium and other heavy metal toxicity and sequester soluble uranium as biominerals could play important role in uranium bioremediation. Copyright © 2010 Elsevier B.V. All rights reserved.

Occurrence, distribution and contamination levels of heat-resistant moulds throughout the processing of pasteurized high-acid fruit products.

Science.gov (United States)

Santos, Juliana Lane Paixão Dos; Samapundo, Simbarashe; Biyikli, Ayse; Van Impe, Jan; Akkermans, Simen; Höfte, Monica; Abatih, Emmanuel Nji; Sant'Ana, Anderson S; Devlieghere, Frank

2018-05-19

Heat-resistant moulds (HRMs) are well known for their ability to survive pasteurization and spoil high-acid food products, which is of great concern for processors of fruit-based products worldwide. Whilst the majority of the studies on HRMs over the last decades have addressed their inactivation, few data are currently available regarding their contamination levels in fruit and fruit-based products. Thus, this study aimed to quantify and identify heat-resistant fungal ascospores from samples collected throughout the processing of pasteurized high-acid fruit products. In addition, an assessment on the effect of processing on the contamination levels of HRMs in these products was carried out. A total of 332 samples from 111 batches were analyzed from three processing plants (=three processing lines): strawberry puree (n = 88, Belgium), concentrated orange juice (n = 90, Brazil) and apple puree (n = 154, the Netherlands). HRMs were detected in 96.4% (107/111) of the batches and 59.3% (197/332) of the analyzed samples. HRMs were present in 90.9% of the samples from the strawberry puree processing line (1-215 ascospores/100 g), 46.7% of the samples from the orange juice processing line (1-200 ascospores/100 g) and 48.7% of samples from the apple puree processing line (1-84 ascospores/100 g). Despite the high occurrence, the majority (76.8%, 255/332) of the samples were either not contaminated or presented low levels of HRMs (processing had no statistically significant effect on the levels of HRMs (p > 0.05). On the contrary, a significant reduction (p levels was observed during the processing of apple puree. Twelve species were identified belonging to four genera - Byssochlamys, Aspergillus with Neosartorya-type ascospores, Talaromyces and Rasamsonia. N. fumigata (23.6%), N. fischeri (19.1%) and B. nivea (5.5%) were the predominant species in pasteurized products. The quantitative data (contamination levels of HRMs) were fitted to exponential

The hyperaccumulator Sedum plumbizincicola harbors metal-resistant endophytic bacteria that improve its phytoextraction capacity in multi-metal contaminated soil.

Science.gov (United States)

Ma, Ying; Oliveira, Rui S; Nai, Fengjiao; Rajkumar, Mani; Luo, Yongming; Rocha, Inês; Freitas, Helena

2015-06-01

Endophyte-assisted phytoremediation has recently been suggested as a successful approach for ecological restoration of metal contaminated soils, however little information is available on the influence of endophytic bacteria on the phytoextraction capacity of metal hyperaccumulating plants in multi-metal polluted soils. The aims of our study were to isolate and characterize metal-resistant and 1-aminocyclopropane-1-carboxylate (ACC) utilizing endophytic bacteria from tissues of the newly discovered Zn/Cd hyperaccumulator Sedum plumbizincicola and to examine if these endophytic bacterial strains could improve the efficiency of phytoextraction of multi-metal contaminated soils. Among a collection of 42 metal resistant bacterial strains isolated from the tissues of S. plumbizincicola grown on Pb/Zn mine tailings, five plant growth promoting endophytic bacterial strains (PGPE) were selected due to their ability to promote plant growth and to utilize ACC as the sole nitrogen source. The five isolates were identified as Bacillus pumilus E2S2, Bacillus sp. E1S2, Bacillus sp. E4S1, Achromobacter sp. E4L5 and Stenotrophomonas sp. E1L and subsequent testing revealed that they all exhibited traits associated with plant growth promotion, such as production of indole-3-acetic acid and siderophores and solubilization of phosphorus. These five strains showed high resistance to heavy metals (Cd, Zn and Pb) and various antibiotics. Further, inoculation of these ACC utilizing strains significantly increased the concentrations of water extractable Cd and Zn in soil. Moreover, a pot experiment was conducted to elucidate the effects of inoculating metal-resistant ACC utilizing strains on the growth of S. plumbizincicola and its uptake of Cd, Zn and Pb in multi-metal contaminated soils. Out of the five strains, B. pumilus E2S2 significantly increased root (146%) and shoot (17%) length, fresh (37%) and dry biomass (32%) of S. plumbizincicola as well as plant Cd uptake (43%), whereas

Geophysical Responses of Hydrocarbon-impacted Zones at the Various Contamination Conditions

Science.gov (United States)

Kim, C.; Ko, K.; Son, J.; Kim, J.

2008-12-01

One controlled experiment and two field surveys were conducted to investigate the geoelectrical responses of hydrocarbon-contaminated zones, so called smeared zone, on the geophysical data at the hydrocarbon- contaminated sites with various conditions. One controlled physical model experiment with GPR using fresh gasoline and two different 3-D electrical resistivity investigations at the aged sites. One field site (former military facilities for arms maintenance) was mainly contaminated with lubricating oils and the other (former gas station) was contaminated with gasoline and diesel, respectively. The results from the physical model experiment show that GPR signals were enhanced when LNAPL was present as a residual saturation in the water-saturated system due to less attenuation of the electromagnetic energy through the soil medium of the hydrocarbon-impacted zone (no biodegradation), compared to when the medium was saturated with only water (no hydrocarbon impaction). In the former gas station site, 3-D resistivity results demonstrate that the highly contaminated zones were imaged with low resistivity anomalies since the biodegradation of petroleum hydrocarbons has been undergone for many years, causing the drastic increase in the TDS at the hydrocarbon-impacted zones. Finally, 3-D resistivity data obtained from the former military maintenance site show that the hydrocarbon-contaminated zones show high resistivity anomalies since the hydrocarbons such as lubricating oils at the contaminated soils were not greatly influenced by microbial degradation and has relatively well kept their original physical properties of high electrical resistivity. The results of the study illustrated that the hydrocarbon-impacted zones under various contamination conditions yielded various geophysical responses which include (1) enhanced GPR amplitudes at the fresh LNAPL (Gasoline to middle distillates) spill sites, (2) low electrical resistivity anomalies due to biodegradation at the

Geophysical Signitures From Hydrocarbon Contaminated Aquifers

Science.gov (United States)

Abbas, M.; Jardani, A.

2015-12-01

The task of delineating the contamination plumes as well as studying their impact on the soil and groundwater biogeochemical properties is needed to support the remediation efforts and plans. Geophysical methods including electrical resistivity tomography (ERT), induced polarization (IP), ground penetrating radar (GPR), and self-potential (SP) have been previously used to characterize contaminant plumes and investigate their impact on soil and groundwater properties (Atekwana et al., 2002, 2004; Benson et al., 1997; Campbell et al., 1996; Cassidy et al., 2001; Revil et al., 2003; Werkema et al., 2000). Our objective was to: estimate the hydrocarbon contamination extent in a contaminated site in northern France, and to adverse the effects of the oil spill on the groundwater properties. We aim to find a good combination of non-intrusive and low cost methods which we can use to follow the bio-remediation process, which is planned to proceed next year. We used four geophysical methods including electrical resistivity tomography, IP, GPR, and SP. The geophysical data was compared to geochemical ones obtained from 30 boreholes installed in the site during the geophysical surveys. Our results have shown: low electrical resistivity values; high chargeability values; negative SP anomalies; and attenuated GPR reflections coincident with groundwater contamination. Laboratory and field geochemical measurements have demonstrated increased groundwater electrical conductivity and increased microbial activity associated with hydrocarbon contamination of groundwater. Our study results support the conductive model suggested by studies such as Sauck (2000) and Atekwana et al., (2004), who suggest that biological alterations of hydrocarbon contamination can substantially modify the chemical and physical properties of the subsurface, producing a dramatic shift in the geo-electrical signature from resistive to conductive. The next stage of the research will include time lapse borehole

Cross-Contamination of Residual Emerging Contaminants and Antibiotic Resistant Bacteria in Lettuce Crops and Soil Irrigated with Wastewater Treated by Sunlight/H2O2.

Science.gov (United States)

Ferro, Giovanna; Polo-López, María I; Martínez-Piernas, Ana B; Fernández-Ibáñez, Pilar; Agüera, Ana; Rizzo, Luigi

2015-09-15

The sunlight/H2O2 process has recently been considered as a sustainable alternative option compared to other solar driven advanced oxidation processes (AOPs) in advanced treatment of municipal wastewater (WW) to be reused for crop irrigation. Accordingly, in this study sunlight/H2O2 was used as disinfection/oxidation treatment for urban WW treatment plant effluent in a compound parabolic collector photoreactor to assess subsequent cross-contamination of lettuce and soil by contaminants of emerging concern (CECs) (determined by QuEChERS extraction and LC-QqLIT-MS/MS analysis) and antibiotic resistant (AR) bacteria after irrigation with treated WW. Three CECs (carbamazepine (CBZ), flumequine (FLU), and thiabendazole (TBZ) at 100 μg L(-1)) and two AR bacterial strains (E. coli and E. faecalis, at 10(5) CFU mL(-1)) were spiked in real WW. A detection limit (DL) of 2 CFU mL(-1) was reached after 120 min of solar exposure for AR E. coli, while AR E. faecalis was more resistant to the disinfection process (240 min to reach DL). CBZ and TBZ were poorly removed after 90 min (12% and 50%, respectively) compared to FLU (94%). Lettuce was irrigated with treated WW for 5 weeks. CBZ and TBZ were accumulated in soil up to 472 ng g(-1) and 256 ng g(-1) and up-taken by lettuce up to 109 and 18 ng g(-1), respectively, when 90 min treated WW was used for irrigation; whereas no bacteria contamination was observed when the bacterial density in treated WW was below the DL. A proper treatment time (>90 min) should be guaranteed in order to avoid the transfer of pathogens from disinfected WW to irrigated crops and soil.

As-resistance in laboratory-reared F1, F2 and F3 generation offspring of the earthworm Lumbricus rubellus inhabiting an As-contaminated mine soil

Energy Technology Data Exchange (ETDEWEB)

Langdon, C.J., E-mail: clangdon1@btinternet.co [C/O The Open University in the North, Baltic Buiness Quarter, Abbots Hill, Gateshead NE8 3DF (United Kingdom); Morgan, A.J., E-mail: morganaj1@cardiff.ac.u [Cardiff School of Biosciences, Cardiff University, P.O. Box 913, Cardiff CF11 3TL, Wales (United Kingdom); Charnock, J.M., E-mail: john.charnock@manchester.ac.u [STFC Daresbury Laboratory, Warrington, Cheshire WA4 4AD (United Kingdom); School of Earth, Atmospheric and Environmental Sciences, University of Manchester, Oxford Road, Manchester M13 9PL (United Kingdom); Semple, K.T., E-mail: k.semple@lancaster.ac.u [Environment Centre, Lancaster University, Lancaster LA1 4YQ (United Kingdom); Lowe, C.N., E-mail: cnlowe@uclan.ac.u [School of Built and Natural Environment, University of Central Lancashire, Preston PR1 2HE (United Kingdom)

2009-11-15

Previous studies provided no unequivocal evidence demonstrating that field populations of Lumbricus rubellus Hoffmeister (1843), exhibit genetically inherited resistance to As-toxicity. In this study F1, F2 and F3 generation offspring derived from adults inhabiting As-contaminated field soil were resistant when exposed to 2000 mg kg{sup -1} sodium arsenate. The offspring of uncontaminated adults were not As-resistant. Cocoon viability was 80% for F1 and 82% for F2 offspring from As-contaminated adults and 59% in the F1 control population. High energy synchrotron analysis was used to determine whether ligand complexation of As differed in samples of: resistant mine-site adults, the resistant F1 and F2 offspring of the mine-site earthworms exposed to the LC{sub 25} sodium arsenate (700 mg kg{sup -1}) of the F1 parental generation; and adult L. rubellus from an uncontaminated site exposed to LC{sub 25} concentrations of sodium arsenate (50 mg kg{sup -1}). XANES and EXAFS indicated that As was present as a sulfur-coordinated species. - As-resistance in F1, F2 and F3 offspring of the earthworm Lumbricus rubellus.

As-resistance in laboratory-reared F1, F2 and F3 generation offspring of the earthworm Lumbricus rubellus inhabiting an As-contaminated mine soil

International Nuclear Information System (INIS)

Langdon, C.J.; Morgan, A.J.; Charnock, J.M.; Semple, K.T.; Lowe, C.N.

2009-01-01

Previous studies provided no unequivocal evidence demonstrating that field populations of Lumbricus rubellus Hoffmeister (1843), exhibit genetically inherited resistance to As-toxicity. In this study F1, F2 and F3 generation offspring derived from adults inhabiting As-contaminated field soil were resistant when exposed to 2000 mg kg -1 sodium arsenate. The offspring of uncontaminated adults were not As-resistant. Cocoon viability was 80% for F1 and 82% for F2 offspring from As-contaminated adults and 59% in the F1 control population. High energy synchrotron analysis was used to determine whether ligand complexation of As differed in samples of: resistant mine-site adults, the resistant F1 and F2 offspring of the mine-site earthworms exposed to the LC 25 sodium arsenate (700 mg kg -1 ) of the F1 parental generation; and adult L. rubellus from an uncontaminated site exposed to LC 25 concentrations of sodium arsenate (50 mg kg -1 ). XANES and EXAFS indicated that As was present as a sulfur-coordinated species. - As-resistance in F1, F2 and F3 offspring of the earthworm Lumbricus rubellus.

Porflow Capabilities, Usage, History, and Testing

International Nuclear Information System (INIS)

Collard, L.B.

1998-05-01

To support closure of the Savannah River Site High Level Waste tanks, the PORFLOW computer program is being applied to predict long term movement of residual contaminants from the tanks. The PORFLOW program has greater capabilities than simpler programs that have been used previously, and PORFLOW results have been accepted by state and federal regulators throughout the United States. This document briefly discusses the PORFLOW capabilities and presents lists of reports showing PORFLOW's usage history and testing

Bioremediation of contaminated soil

International Nuclear Information System (INIS)

Balba, M.T.; Ying, A.C.; McNeice, T.G.

1992-01-01

Microorganisms, especially bacteria, yeast and fungi are capable of degrading many kinds of xenobiotic compounds and toxic chemicals such as petroleum hydrocarbon compounds. These microorganisms are ubiquitous in nature and, despite their enormous versatility, there are numerous cases in which long-term contamination of soil and groundwater has been observed. The persistence of the contamination is usually caused by the inability of microorganisms to metabolize these compounds under the prevailing environmental condition. This paper reports on biological remediation of contaminated sites which can be accomplished by using naturally-occurring microorganisms to treat the contaminants. The development of a bioremediation program for a specific contaminated soil system usually includes: A thorough site/soil/waste characterization; Treatability studies

Imaging Preferential Flow Pathways of Contaminants from Passive Acid Mine Drainage Mitigation Sites Using Electrical Resistivity

Science.gov (United States)

Kelley, N.; Mount, G.; Terry, N.; Herndon, E.; Singer, D. M.

2017-12-01

The Critical Zone represents the surficial and shallow layer of rock, air, water, and soil where most interactions between living organisms and the Earth occur. Acid mine drainage (AMD) resulting from coal extraction can influence both biological and geochemical processes across this zone. Conservative estimates suggest that more than 300 million gallons of AMD are released daily, making this acidic solution of water and contaminants a common issue in areas with legacy or current coal extraction. Electrical resistivity imaging (ERI) provides a rapid and minimally invasive method to identify and monitor contaminant pathways from AMD remediation systems in the subsurface of the Critical Zone. The technique yields spatially continuous data of subsurface resistivity that can be inverted to determine electrical conductivity as a function of depth. Since elevated concentrations of heavy metals can directly influence soil conductivity, ERI data can be used to trace the flow pathways or perhaps unknown mine conduits and transport of heavy metals through the subsurface near acid mine drainage sources. This study aims to examine preferential contaminant migration from those sources through substrate pores, fractures, and shallow mine workings in the near subsurface surrounding AMD sites in eastern Ohio and western Pennsylvania. We utilize time lapse ERI measures during different hydrologic conditions to better understand the variability of preferential flow pathways in relation to changes in stage and discharge within the remediation systems. To confirm ERI findings, and provide constraint to geochemical reactions occurring in the shallow subsurface, we conducted Inductively Coupled Plasma (ICP) spectrometry analysis of groundwater samples from boreholes along the survey transects. Through these combined methods, we can provide insight into the ability of engineered systems to contain and isolate metals in passive acid mine drainage treatment systems.

Resident cats in small animal veterinary hospitals carry multi-drug resistant enterococci and are likely involved in cross-contamination of the hospital environment

Directory of Open Access Journals (Sweden)

Anuradha eGhosh

2012-02-01

Full Text Available In the U.S., small animal veterinary hospitals (SAVHs commonly keep resident cats living permanently as pets within their facilities. Previously, multi-drug resistant (MDR enterococci were found as a contaminant of multiple surfaces within such veterinary hospitals, and nosocomial infections are a concern. The objectives of this study were to determine whether resident cats carry MDR enterococci and if they potentially play a role in the contamination of the hospital environment. Enterococcal strains (n=180 were isolated from the feces of six healthy resident cats from different SAVHs. The concentration of enterococci ranged from 1.1 x 105 to 6.0 x 108 CFU g-1 of feces, and the population comprised E. hirae (38.3±18.6%, E. faecium (35.0±14.3%, E. faecalis (23.9±11.0%, and E. avium (2.8±2.2%. Testing of phenotypic resistance to 14 antimicrobial agents revealed multi-drug resistance (≥3 antimicrobials in 48.9% of all enterococcal isolates with most frequent resistance to tetracycline (72.8%, erythromycin (47.8%, and rifampicin (35.6%. Vancomycin resistant E. faecalis (3.9% with vanB not horizontally transferable in in vitro conjugation assays were detected from one cat. Genotyping (pulsed-field gel electrophoresis demonstrated a host-specific clonal population of MDR E. faecalis and E. faecium. Importantly, several feline isolates were genotypically identical or closely related to isolates from surfaces of cage door, thermometer, and stethoscope of the corresponding SAVHs. These data demonstrate that healthy resident cats at SAVHs carry MDR enterococci and likely contribute to contamination of the SAVH environment. Proper disposal and handling of fecal material and restricted movement of resident cats within the ward is recommended.

Contamination of environmental surfaces by methicillin-resistant Staphylococcus aureus (MRSA) in rooms of inpatients with MRSA-positive body sites.

Science.gov (United States)

Kurashige, E Jessica Ohashi; Oie, Shigeharu; Furukawa, H

2016-01-01

Methicillin-resistant Staphylococcus aureus (MRSA) can contaminate environmental surfaces that are frequently touched by the hands of patients with MRSA colonization/infection. There have been many studies in which the presence or absence of MRSA contamination was determined but no studies in which MRSA contamination levels were also evaluated in detail. We evaluated MRSA contamination of environmental surfaces (overbed tables, bed side rails, and curtains) in the rooms of inpatients from whom MRSA was isolated via clinical specimens. We examined the curtains within 7-14 days after they had been newly hung. The environmental surfaces were wiped using gauze (molded gauze for wiping of surface bacteria; 100% cotton, 4cm×8cm) moistened with sterile physiological saline. The MRSA contamination rate and mean counts (range) were 25.0% (6/24 samples) and 30.6 (0-255)colony-forming units (cfu)/100cm(2), respectively, for the overbed tables and 31.6% (6/19 samples) and 159.5 (0-1620)cfu/100cm(2), respectively, for the bed side rails. No MRSA was detected in 24 curtain samples. The rate of MRSA contamination of environmental surfaces was high for the overbed tables and bed side rails but low for the curtains. Therefore, at least until the 14th day of use, frequent disinfection of curtains may be not necessary. Copyright © 2016. Published by Elsevier Editora Ltda.

PREVALENCE AND ANTIBIOTIC RESISTANCE OF FOOD BORNE BACTERIAL CONTAMINATION IN SOME EGYPTIAN FOOD food

Directory of Open Access Journals (Sweden)

Samy Selim

2015-09-01

Full Text Available This study was undertaken to investigate the prevalence and antibiotic resistance of food borne bacterial contamination in some Egyptian food. Total viable bacteria and total coliform bacteriawere isolated from different sources of food; carbohydrates (bread, flour and basbousa, vegetables (outer and inner tissues of potato and outer and inner tissues of cucumber and proteins (mincedmeat, cheese and milk. The study resulted in maximum value of total viable bacteria found in outer tissue of potato 68X104±1.0, while the minimum value found in inner tissues of potato andcucumber. The study resulted in total coliform was maximum value in minced meat 6.4X103±0.3. Basbousa and inner tissue of potato and cucumber were free from coliforms. The ability of isolatesto producing proteolytic enzymes was tested, we found that 326 isolate (63.92% from all isolates had this ability, thus we selected most 2 potent proteolytic isolates. The two isolates were identifiedas Bacillus cereus and Escherichia coli. The identification confirmed by microlog 34.20 system and 16SrRNA for two isolates and the same result was founded. Sensitivity tested for the most potentproteolytic species to 12 of the most commonly used antibiotics in the Egyptian pharmacy. The results showed that all species were sensitive to most of antibiotics, except B. cereus which was strongly susceptible to azteronam and ceftazidim. The data showed that raw meat, cooked food products, and raw milk were most commonly contaminated with foodborne pathogens and many pathogens were resistant to different antibiotics. The study provided useful information for assessment of the possible risk posed to consumers, which has significant public health impact.

Endosulfan Resistance Profile of Soil Bacteria and Potential Application of Resistant Strains in Bioremediation

Directory of Open Access Journals (Sweden)

Chandini P.K.

2014-05-01

Full Text Available In the present study, bacterial strains were isolated from the soils of Wayanad District, Kerala, India and the isolates were tested for their tolerance to endosulfan and potential in bioremediation technology. Pesticide contamination in the soils, soil physico-chemical characteristics and socio-economic impacts of pesticide application were also analyzed. 28 pesticide compounds in the soil samples were analyzed and the results revealed that there was no pesticide residues in the soils. As per the survey conducted the pesticide application is very high in the study area and the level of awareness among the farmers was very poor regarding the method of application and its socio-economic and ecological impacts. A total of 9 bacterial strains were isolated with 50μg/ml of endosulfan in the isolating media and the results showed that most of the bacterial strains were highly resistance to endosulfan. Out of the 9 strains isolated 6 were highly resistant to endosulfan (500- 700μg/ml and the other 3 isolates showed the resistance of 250-500μg/ml. From the studied isolate, isolate 9 demonstrating prolific growth and high resistance was selected to check their capability to degrade endosulfan over time. Identification of the selected strain reveals that it belongs to the genus Bacillus. Results of endosulfan removal studies showed that with increase in time, the biomass of the bacterial strains increased. The complete disappearance of endosulfan from the spiked and inoculated broth during the first day of incubation (24 hour interval was observed. While the control flask showed the presence of endosulfan during the experimental period. Pesticide resistant bacteria are widely distributed in the soils of selected study area and the tolerance varied between bacteria even though they were isolated from the soils of the same area. The selected Bacillus species carry the ability to degrade endosulfan at accelerated rates and it could be useful in framing a

Improving global laboratory capabilities for emergency radionuclide bioassay

International Nuclear Information System (INIS)

Li, C.; Jourdain, J.; Kramer, G. H.

2012-01-01

During a radiological or nuclear emergency, first-responders and the general public may be internally contaminated with the radionuclide(s) involved. A timely radionuclide bioassay provides important information about contamination, for subsequent dose assessment and medical management. Both technical and operational gaps are discussed in this paper. As many people may need to be assessed in a short period of time, any single laboratory may find its capabilities insufficient. Laboratories from other regions or other countries may be called upon for assistance. This paper proposes a road-map to improve global capabilities in emergency radionuclide bioassay, suggesting a phased approach for establishing a global laboratory network. Existing international collaboration platforms could provide the base on which to build such a network. (authors)

Isolation and characterization of a chromium-resistant bacterium Serratia sp. Cr-10 from a chromate-contaminated site.

Science.gov (United States)

Zhang, Kundi; Li, Fuli

2011-05-01

A novel bacterium, Cr-10, was isolated from a chromium-contaminated site and capable of removing toxic chromium species from solution by reducing hexavalent chromium to an insoluble precipitate. Sequence analysis of 16S rRNA gene of strain Cr-10 showed that it was most closely related to Serratia rubidaea JCM 1240(T) (97.68%). Physiological and chemotaxonomic data also supported that strain Cr-10 was identified as Serratia sp., a genus which was never specially reported chromate-resistant before. Serratia sp., Cr-10 was tolerant to a concentration of 1,500 mg Cr(VI) L(-1), which was the highest level reported until now. The optimum pH and temperature for reduction of Cr(VI) by Serratia sp. Cr-10 were found to be 7.0 and 37 °C, respectively. The Cr(VI) reduction was significantly influenced by additional carbon sources, and among them fructose and lactose offered maximum reduction, with a rate of 0.28 and 0.25 mg Cr(VI) L(-1) h(-1), respectively. The cell-free extracts and filtrate of the culture were able to reduce Cr(VI) while concentration of total chromium remained stable in the process, indicating that the enzyme-catalyzed mechanism was applied in Cr(VI) reduction by the isolate. Additionally, it was found that there was hardly any chromium on the cell surface of the strain, further supporting that reduction, rather than bioadsorption, plays a major role in the Cr(VI) removal.

Isolation and characterization of a chromium-resistant bacterium Serratia sp. Cr-10 from a chromate-contaminated site

Energy Technology Data Exchange (ETDEWEB)

Zhang, Kundi; Li, Fuli [Chinese Academy of Sciences, Qingdao (China). Qingdao Inst. of Bioenergy and Bioprocess Technology

2011-05-15

A novel bacterium, Cr-10, was isolated from a chromium-contaminated site and capable of removing toxic chromium species from solution by reducing hexavalent chromium to an insoluble precipitate. Sequence analysis of 16S rRNA gene of strain Cr-10 showed that it was most closely related to Serratia rubidaea JCM 1240{sup T} (97.68%). Physiological and chemotaxonomic data also supported that strain Cr-10 was identified as Serratia sp., a genus which was never specially reported chromate-resistant before. Serratia sp., Cr-10 was tolerant to a concentration of 1,500 mg Cr(VI) L{sup -1}, which was the highest level reported until now. The optimum pH and temperature for reduction of Cr(VI) by Serratia sp. Cr-10 were found to be 7.0 and 37 C, respectively. The Cr(VI) reduction was significantly influenced by additional carbon sources, and among them fructose and lactose offered maximum reduction, with a rate of 0.28 and 0.25 mg Cr(VI) L{sup -1} h{sup -1}, respectively. The cell-free extracts and filtrate of the culture were able to reduce Cr(VI) while concentration of total chromium remained stable in the process, indicating that the enzyme-catalyzed mechanism was applied in Cr(VI) reduction by the isolate. Additionally, it was found that there was hardly any chromium on the cell surface of the strain, further supporting that reduction, rather than bioadsorption, plays a major role in the Cr(VI) removal. (orig.)

Multiple antibiotic resistant Escherichia coli from a tropical rain forest stream

Energy Technology Data Exchange (ETDEWEB)

Carrasco, C.E.; Alvarez, H.J.; Ortiz, N.; Bisbal, M.; Arias, W.; Baerga, C. [Univ. of Puerto Rico, Rio Piedras (Puerto Rico). Dept. of Biology; Hazen, T.C. [E.I. DuPont de Nemours and Co., Aiken, SC (United States). Savannah River Lab.

1988-12-31

High densities of fecal coliforms were obtained from a pristine site and sewage contaminated site in a tropical rain forest watershed in Puerto Rico. Confirmation of fecal coliform isolates as Escherichia coli was significantly lower than for temperate waters. Antibiotic resistance and multiple antibiotic resistance were common for isolates at both sites; however, the site receiving sewage effluent had a greater proportion of multiple antibiotic resistant isolates. R. plasmids were recovered from 4 MAR isolates, 2 from each site. All recovered plasmids were approximately 1 kilobase. The recovered plasmid were also capable of transforming E. coli HB101 in vitro. The high concentrations of enterobacteriaceae, small R-plasmid size, R-plasmid transformability, and long term survival of fecal origin bacteria in tropical freshwater environments give increasing importance to adequate sewage treatment, and better indicator monitoring methods for tropical areas.

Extreme Ionizing-Radiation-Resistant Bacterium

Science.gov (United States)

Vaishampayan, Parag A.; Venkateswaran, Kasthuri J.; Schwendner, Petra

2013-01-01

There is a growing concern that desiccation and extreme radiation-resistant, non-spore-forming microorganisms associated with spacecraft surfaces can withstand space environmental conditions and subsequent proliferation on another solar body. Such forward contamination would jeopardize future life detection or sample return technologies. The prime focus of NASA s planetary protection efforts is the development of strategies for inactivating resistance-bearing micro-organisms. Eradi cation techniques can be designed to target resistance-conferring microbial populations by first identifying and understanding their physiologic and biochemical capabilities that confers its elevated tolerance (as is being studied in Deinococcus phoenicis, as a result of this description). Furthermore, hospitals, food, and government agencies frequently use biological indicators to ensure the efficacy of a wide range of radiation-based sterilization processes. Due to their resistance to a variety of perturbations, the nonspore forming D. phoenicis may be a more appropriate biological indicator than those currently in use. The high flux of cosmic rays during space travel and onto the unshielded surface of Mars poses a significant hazard to the survival of microbial life. Thus, radiation-resistant microorganisms are of particular concern that can survive extreme radiation, desiccation, and low temperatures experienced during space travel. Spore-forming bacteria, a common inhabitant of spacecraft assembly facilities, are known to tolerate these extreme conditions. Since the Viking era, spores have been utilized to assess the degree and level of microbiological contamination on spacecraft and their associated spacecraft assembly facilities. Members of the non-sporeforming bacterial community such as Deinococcus radiodurans can survive acute exposures to ionizing radiation (5 kGy), ultraviolet light (1 kJ/m2), and desiccation (years). These resistive phenotypes of Deinococcus enhance the

JPL Contamination Control Engineering

Science.gov (United States)

Blakkolb, Brian

2013-01-01

JPL has extensive expertise fielding contamination sensitive missions-in house and with our NASA/industry/academic partners.t Development and implementation of performance-driven cleanliness requirements for a wide range missions and payloads - UV-Vis-IR: GALEX, Dawn, Juno, WFPC-II, AIRS, TES, et al - Propulsion, thermal control, robotic sample acquisition systems. Contamination control engineering across the mission life cycle: - System and payload requirements derivation, analysis, and contamination control implementation plans - Hardware Design, Risk trades, Requirements V-V - Assembly, Integration & Test planning and implementation - Launch site operations and launch vehicle/payload integration - Flight ops center dot Personnel on staff have expertise with space materials development and flight experiments. JPL has capabilities and expertise to successfully address contamination issues presented by space and habitable environments. JPL has extensive experience fielding and managing contamination sensitive missions. Excellent working relationship with the aerospace contamination control engineering community/.

Biosorption of Lead by Pseudomonas sp Isolated from Oil-Contaminated Wastewaters in Khuzestan

Directory of Open Access Journals (Sweden)

Seyed Mansour Meybodi

2015-05-01

Full Text Available Biosorption is a most effective technology for the removal of such toxic substances as heavy metals. The objective of this study was four-fold: 1 to isolate lead resistant Pseudomonas strains, 2 to determine the optimal conditions of their growth, 3 to obtain the minimum inhibitory concentration of lead, and 4 to evaluate the bioremoval of lead from culture solutions. For the purposes of this study, oil-contaminated wastewater samples were collected from Khuzestan region and transferred to laboratory where they were homogenized and serially diluted up to 10-10 with sterile saline before they were cultured in Luria Bertani agar medium containing 5ppm of lead nitrate. Resistant strains were then isolated at 37°C for 24h. The samples were subsequently cultured in Macconkey agar for isolation of appropriate gram negative strains. Biochemical tests were used to identify the bacteria, 10 strains of which were screened as lead resistant ones from all the 24 isolates. The bacterial colonies were selected and tested with different concentrations (100- 2100 ppm of lead for their resistance. The plates were then incubated at 37ºC for 24h and Mso1 was chosen from among the lead resistant colonies for further experiments. This strain showed resistance to chloramphenicol (30µg and erythromycin (15µg when subjected to the antimicrobial susceptibility test. Optimal growth conditions included a temperature of 40°C at 100 rpm and a pH level of 6 in the presence of lead by spectrophotometry at 600nm. Absorption tests showed that the Mso1 strain had a metal removal efficiency of 38.45% from an aqueous solution containing 100 ppm of lead over 24h. The results confirmed the capability of Pseudomonassp in the bioremediation of Pb-contaminated wastewaters.

Canadian national nuclear forensics capability project

International Nuclear Information System (INIS)

Ball, J.; Dimayuga, I.; Summerell, I.; Totland, M.; Jonkmans, G.; Whitlock, J.; El-jaby, A.; Inrig, E.

2015-01-01

Following the 2010 Nuclear Security Summit, Canada expanded its existing capability for nuclear forensics by establishing a national nuclear forensics laboratory network, which would include a capability to perform forensic analysis on nuclear and other radioactive material, as well as on traditional evidence contaminated with radioactive material. At the same time, the need for a national nuclear forensics library of signatures of nuclear and radioactive materials under Canadian regulatory control was recognized. The Canadian Safety and Security Program, administered by Defence Research and Development Canada's Centre for Security Science (DRDC CSS), funds science and technology initiatives to enhance Canada's preparedness for prevention of and response to potential threats. DRDC CSS, with assistance from Canadian Nuclear Laboratories, formerly Atomic Energy of Canada Limited, is leading the Canadian National Nuclear Forensics Capability Project to develop a coordinated, comprehensive, and timely national nuclear forensics capability. (author)

Microbial Functional Gene Diversity Predicts Groundwater Contamination and Ecosystem Functioning.

Science.gov (United States)

He, Zhili; Zhang, Ping; Wu, Linwei; Rocha, Andrea M; Tu, Qichao; Shi, Zhou; Wu, Bo; Qin, Yujia; Wang, Jianjun; Yan, Qingyun; Curtis, Daniel; Ning, Daliang; Van Nostrand, Joy D; Wu, Liyou; Yang, Yunfeng; Elias, Dwayne A; Watson, David B; Adams, Michael W W; Fields, Matthew W; Alm, Eric J; Hazen, Terry C; Adams, Paul D; Arkin, Adam P; Zhou, Jizhong

2018-02-20

Contamination from anthropogenic activities has significantly impacted Earth's biosphere. However, knowledge about how environmental contamination affects the biodiversity of groundwater microbiomes and ecosystem functioning remains very limited. Here, we used a comprehensive functional gene array to analyze groundwater microbiomes from 69 wells at the Oak Ridge Field Research Center (Oak Ridge, TN), representing a wide pH range and uranium, nitrate, and other contaminants. We hypothesized that the functional diversity of groundwater microbiomes would decrease as environmental contamination (e.g., uranium or nitrate) increased or at low or high pH, while some specific populations capable of utilizing or resistant to those contaminants would increase, and thus, such key microbial functional genes and/or populations could be used to predict groundwater contamination and ecosystem functioning. Our results indicated that functional richness/diversity decreased as uranium (but not nitrate) increased in groundwater. In addition, about 5.9% of specific key functional populations targeted by a comprehensive functional gene array (GeoChip 5) increased significantly ( P contamination and ecosystem functioning. This study indicates great potential for using microbial functional genes to predict environmental contamination and ecosystem functioning. IMPORTANCE Disentangling the relationships between biodiversity and ecosystem functioning is an important but poorly understood topic in ecology. Predicting ecosystem functioning on the basis of biodiversity is even more difficult, particularly with microbial biomarkers. As an exploratory effort, this study used key microbial functional genes as biomarkers to provide predictive understanding of environmental contamination and ecosystem functioning. The results indicated that the overall functional gene richness/diversity decreased as uranium increased in groundwater, while specific key microbial guilds increased significantly as

Enterotoxigenicity and Antimicrobial Resistance of Staphylococcus aureus Isolated from Retail Food in China

Science.gov (United States)

Wang, Wei; Baloch, Zulqarnain; Jiang, Tao; Zhang, Cunshan; Peng, Zixin; Li, Fengqin; Fanning, Séamus; Ma, Aiguo; Xu, Jin

2017-01-01

Staphylococcus aureus is one of the most common causes of zoonotic agent in the world, which are attributable to the contamination of food with enterotoxins. In this study, a total of 1,150 S. aureus isolates were cultured from 27,000 retail foods items from 203 cities of 24 provinces in China in 2015 and were test for antimicrobial susceptibility. Additionally, the role of the genes responsible for the staphylococcal enterotoxins (SEA to SEE), methicillin resistance (mecA) and the toxigenic capabilities were also assessed. The results showed that 4.3% retail foods were contaminated with S. aureus, and 7.9% retail foods isolates were mecA positive. Some 97.6% of S. aureus isolates were resistant to at least one antimicrobial compound, and 57.5% of these were multi drug resistant (MDR). Resistance to penicillin (83.7%, 963/1,150), was common, followed by linezolid (67.7%, 778/1,150) and erythromycin (52.1%, 599/1,150). The isolates cultured from raw meats showed high levels of resistant to tetracycline (42.8%), ciprofloxacin (17.4%), and chloramphenicol (12.0%) and expressed a MDR phenotype (62.4%). A total of 29.7% S. aureus isolates harbored the classical SEs genes (sea, seb, sec, and sed). The sea and seb genes were the most frequent SEs genes detected. Of note, 22% of the SEs genes positive S. aureus harbored two or three SEs genes, and 16 isolates were confirmed with the capacity to simultaneously produce two or three enterotoxin types. Moreover, nearly 50% of the MRSA isolates were positive for at least one SE gene in this study. Therefore, it is important to monitor the antimicrobial susceptibility and enterotoxigenicity of MDR S. aureus and MRSA in the food chain and to use these data to develop food safety measures, designed to reduce the contamination and transmission of this bacterium. PMID:29209290

Resistance welding equipment manufacturing capability for exports

Energy Technology Data Exchange (ETDEWEB)

Sastry, V.S.; Raju, Y.S.; Somani, A.K.; Setty, D.S.; Rameswara Raw, A.; Hermantha Rao, G.V.S.; Jayaraj, R.N. [Nuclear Fuel Complex, Dept. of Atomic Energy, Hyderbad (India)

2010-07-01

Indian Pressurised Heavy Water Reactor (PHWR) fuel bundle is fully welded and is unique in its design. Appendage welding, end closure welding, and end plate welding is carried out using resistance welding technique. Out of many joining processes available, resistance-welding process is reliable, environment friendly and best suitable for mass production applications. Nuclear Fuel Complex (NFC), an industrial unit is established in Hyderabad, under the aegis of the Dept of Atomic Energy to manufacture fuel for Pressurised Heavy Water Reactors. From inception, NFC has given importance for self-reliance and indigenization with respect to manufacturing process and equipment. Sintering furnaces, centreless grinders, appendage-welding machines, end-closure welding equipment and end-plate welding equipments, which were initially imported, are either indigenized or designed and manufactured in house. NFC has designed, manufactured a new appendage-welding machine for manufacturing 37 element fuel bundles. Recently NFC has bagged an order from IAEA through international bidding for design, manufacture, supply, erection and commissioning of end-closure welding equipment. The paper gives in detail the salient features of these welding equipment. (author)

Isolation and characterization of bacteria from mercury contaminated sites in Rio Grande do Sul, Brazil, and assessment of methylmercury removal capability of a Pseudomonas putida V1 strain.

Science.gov (United States)

Cabral, Lucélia; Giovanella, Patrícia; Gianello, Clésio; Bento, Fátima Menezes; Andreazza, Robson; Camargo, Flávio Anastácio Oliveira

2013-06-01

Methylmercury (MeHg) is one of the most dangerous heavy metal for living organisms that may be found in environment. Given the crescent industrialization of Brazil and considering that mercury is a residue of several industrial processes, there is an increasing need to encounter and develop remediation approaches of mercury contaminated sites. The aim of this study was to isolate and characterize methylmercury resistant bacteria from soils and sludge sewage from Rio Grande do Sul, Brazil. Sixteen bacteria were isolated from these contaminated sites and some isolates were highly resistant to methylmercury (>8.7 μM). All the isolates were identified by 16S rDNA. Pseudomonas putida V1 was able to volatilize approximately 90 % of methylmercury added to growth media and to resist to copper, lead, nickel, chromate, zinc, cobalt, manganese and barium. In the presence of high concentrations of methylmercury (12 μM), cell growth was limited, but P. putida V1 was still able to remove up to 29 % of this compound from culture medium. This bacterium removed an average of 77 % of methylmercury from culture medium with pH in the range 4.0-6.0. In addition, methylmercury was efficiently removed (>80 %) in temperature of 21-25 °C. Polymerase chain reactions indicated the presence of merA but not merB in P. putida V1. The growth and ability of P. putida V1 to remove methylmercury in a wide range of pH (4.0 and 8.0) and temperature (10-35 °C), its tolerance to other heavy metals and ability to grow in the presence of up to 11.5 μM of methylmercury, suggest this strain as a new potential resource for degrading methylmercury contaminated sites.

Canadian national nuclear forensics capability project

Energy Technology Data Exchange (ETDEWEB)

Ball, J.; Dimayuga, I., E-mail: joanne.ball@cnl.ca [Canadian Nuclear Laboratories, Chalk River, Ontario (Canada); Summerell, I. [Royal Canadian Mounted Police, Ottawa, Ontario (Canada); Totland, M. [Canadian Nuclear Laboratories, Chalk River, Ontario (Canada); Jonkmans, G. [Defence Research and Development Canada, Ottawa, Ontario (Canada); Whitlock, J. [Canadian Nuclear Laboratories, Chalk River, Ontario (Canada); El-jaby, A. [Canadian Nuclear Safety Commission, Ottawa, Ontario (Canada); Inrig, E. [Defence Research and Development Canada, Ottawa, Ontario (Canada)

2015-06-15

Following the 2010 Nuclear Security Summit, Canada expanded its existing capability for nuclear forensics by establishing a national nuclear forensics laboratory network, which would include a capability to perform forensic analysis on nuclear and other radioactive material, as well as on traditional evidence contaminated with radioactive material. At the same time, the need for a national nuclear forensics library of signatures of nuclear and radioactive materials under Canadian regulatory control was recognized. The Canadian Safety and Security Program, administered by Defence Research and Development Canada's Centre for Security Science (DRDC CSS), funds science and technology initiatives to enhance Canada's preparedness for prevention of and response to potential threats. DRDC CSS, with assistance from Canadian Nuclear Laboratories, formerly Atomic Energy of Canada Limited, is leading the Canadian National Nuclear Forensics Capability Project to develop a coordinated, comprehensive, and timely national nuclear forensics capability. (author)

Effects of corresponding and non-corresponding contaminants on the fate of sulfonamide and quinolone resistance genes in the Laizhou Bay, China.

Science.gov (United States)

Li, Qianwei; Na, Guangshui; Zhang, Linxiao; Lu, Zihao; Gao, Hui; Li, Ruijing; Jin, Shuaichen

2018-03-01

The environmental behaviors and migration patterns of antibiotic resistance genes (ARGs) have attracted considerable research interest. However, there has been little research concerning the effects of corresponding and non-corresponding contaminants on the fate of ARGs in coastal environments. In the present study, the distribution of intI1, sul1, sul2, qnrS and aac(6')-Ib were analyzed in water and sediment samples of Laizhou Bay in the context of corresponding and non-corresponding contaminants. The abundance of intI1, sul1 and sul2 genes exhibited a clear decreasing trend extending from the inner estuary to the coastal area. Strong and positive correlations existed between sul1/sul2 and sulfonamide antibiotic residues in sediments, and between the abundances of intI1 and sul1/sul2. Statistical analyses indicated that non-corresponding contaminants were partially correlated with ARG abundances. These results suggest that non-corresponding contaminants may have direct or indirect influences on the abundances of ARGs and intI1 in the Laizhou Bay. Copyright © 2018 Elsevier Ltd. All rights reserved.

Biotechnological advances for combating Aspergillus flavus and aflatoxin contamination in crops.

Science.gov (United States)

Bhatnagar-Mathur, Pooja; Sunkara, Sowmini; Bhatnagar-Panwar, Madhurima; Waliyar, Farid; Sharma, Kiran Kumar

2015-05-01

Aflatoxins are toxic, carcinogenic, mutagenic, teratogenic and immunosuppressive byproducts of Aspergillus spp. that contaminate a wide range of crops such as maize, peanut, and cotton. Aflatoxin not only affects crop production but renders the produce unfit for consumption and harmful to human and livestock health, with stringent threshold limits of acceptability. In many crops, breeding for resistance is not a reliable option because of the limited availability of genotypes with durable resistance to Aspergillus. Understanding the fungal/crop/environment interactions involved in aflatoxin contamination is therefore essential in designing measures for its prevention and control. For a sustainable solution to aflatoxin contamination, research must be focused on identifying and improving knowledge of host-plant resistance factors to aflatoxin accumulation. Current advances in genetic transformation, proteomics, RNAi technology, and marker-assisted selection offer great potential in minimizing pre-harvest aflatoxin contamination in cultivated crop species. Moreover, developing effective phenotyping strategies for transgenic as well as precision breeding of resistance genes into commercial varieties is critical. While appropriate storage practices can generally minimize post-harvest aflatoxin contamination in crops, the use of biotechnology to interrupt the probability of pre-harvest infection and contamination has the potential to provide sustainable solution. Copyright © 2015 Elsevier Ireland Ltd. All rights reserved.

The update of resist outgas testing for metal containing resists at EIDEC

Science.gov (United States)

Shiobara, Eishi; Mikami, Shinji

2017-10-01

The metal containing resist is one of the candidates for high sensitivity resists. EIDEC has prepared the infrastructure for outgas testing in hydrogen environment for metal containing resists at High Power EUV irradiation tool (HPEUV). We have experimentally obtained the preliminary results of the non-cleanable metal contamination on witness sample using model material by HPEUV [1]. The metal contamination was observed at only the condition of hydrogen environment. It suggested the generation of volatile metal hydrides by hydrogen radicals. Additionally, the metal contamination on a witness sample covered with Ru was not removed by hydrogen radical cleaning. The strong interaction between the metal hydride and Ru was confirmed by the absorption simulation. Recently, ASML announced a resist outgassing barrier technology using Dynamic Gas Lock (DGL) membrane located between projection optics and wafer stage [2], [3]. DGL membrane blocks the diffusion of all kinds of resist outgassing to the projection optics and prevents the reflectivity loss of EUV mirrors. The investigation of DGL membrane for high volume manufacturing is just going on. It extends the limitation of material design for EUV resists. However, the DGL membrane has an impact for the productivity of EUV scanners due to the transmission loss of EUV light and the necessity of periodic maintenance. The well understanding and control of the outgassing characteristics of metal containing resists may help to improve the productivity of EUV scanner. We consider the outgas evaluation for the resists still useful. For the improvement of resist outgas testing by HPEUV, there are some issues such as the contamination limited regime, the optimization of exposure dose to obtain the measurable contamination film thickness and the detection of minimum amount of metal related outgas species generated. The investigation and improvement for these issues are ongoing. The updates will be presented in the conference. This

Contamination of lettuce with antibiotic resistant E. coli after slurry application

DEFF Research Database (Denmark)

Jensen, Annette Nygaard; Storm, Christina; Baggesen, Dorte Lau

2011-01-01

Due to disease outbreaks associated with contaminated vegetables it has been speculated to what extent this may be linked with application of animal manure as fertilizer, which is particularly practiced in organic vegetable production where conventional fertilizers are prohibited. A field survey......, where 20% of faecally contaminated samples contained >100 E. coli/g. This indicates that fecal contamination of crops originated from alternative sources such as contaminated water or wildlife. This was supported by genotyping of E. coli, where half of the 21 PFGE types were found on single occasions...

Radiation resistance of microorganisms on unsterilized infusion sets

DEFF Research Database (Denmark)

Christensen, E. Ahrensburg; Kristensen, H.; Hoborn, J.

1991-01-01

Three different methods were used for detecting and isolating microorganisms with high radiation resistance from the microbial contamination on infusion sets prior to sterilization. By all three methods, microorganisms with a radiation resistance high enough to be a critical factor in a steriliza......Three different methods were used for detecting and isolating microorganisms with high radiation resistance from the microbial contamination on infusion sets prior to sterilization. By all three methods, microorganisms with a radiation resistance high enough to be a critical factor...

Effects of pesticides and contaminants on neotropical migrants

Science.gov (United States)

Nicholas W. Gard; Michael J. Hooper; Richard S. Bennett

1993-01-01

Many agricultural pesticides and industrial contaminants are capable of adversely affecting birds through direct effects such as elevated mortality rates and decreased reproductive success or indirectly by modifying habitat composition or food availability. Although neotropical migrants are potentially exposed to these contaminants on their breeding, migratory and...

Nickel contaminated titanium weld wire study

International Nuclear Information System (INIS)

Coffin, G.R.; Sumstine, R.L.

1979-01-01

Attachment of thermocouples to fuel rod welding problems at Exxon Nuclear Company and INEL prompted an investigation study of the titanium filler wire material. It was found that the titanium filler wire was contaminated with nickel which was jacketed on the wire prior to the drawing process at the manufacturers. A method was developed to 100% inspect all filler wire for future welding application. This method not only indicates the presence of nickel contamination but indicates quantity of contamination. The process is capable of high speed inspection necessary for various high speed manufacturing processes

Bioremediation capability and characterization of bacteria isolated from petroleum contaminated soils in Iran

Directory of Open Access Journals (Sweden)

Golafarin Ghoreishi

2017-07-01

Full Text Available This study was carried out to isolate bacteria for bioremediation of petroleum polluted soils. Five samples were used for isolation in this study. They were four soil samples in addition to one kerosene sample. The soil samples including soils contaminated by crude oil and gas oil and two soil samples with no outward contamination which were collected from Shiraz Oil Refinery sites. Seven strains were selected among the isolated colonies for further experiments. The selected isolates were cultured in standard succinate medium (SSM minimal medium in which 2.5% v/v kerosene was used as carbon source. In another bacterial SSM culture, carbon, sulfur or nitrogen source was removed and 20% v/v kerosene added to check the ability of isolates to utilizekerosene as sole source for C, N and S. Finally, cultures of four strains with higher growth in modified SSM cultures were selected for GC analysis. In this study they were named C2 and C4 which were isolated from crude oil contaminated soil and SI1 and SI2 isolated from soils with no outward contamination. GC analysis showed that C2 could degrade 69% of 5% v/v kerosene in 7 d, while C4 and SI1 degraded 48% and 42% of 5% v/v kerosene during this 7-d period respectively, and the degradation ability of SI2 was 38% after 7 d. Analysis of 16S rRNA gene showed that C2 was close to Citrobacter sedlakii, C4 and SI1 were related to Entrobacter hormeachei and SI2 was close to Entrobacter cloacae, respectively.

Transcriptome Response to Heavy Metals in Sinorhizobium meliloti CCNWSX0020 Reveals New Metal Resistance Determinants That Also Promote Bioremediation by Medicago lupulina in Metal-Contaminated Soil.

Science.gov (United States)

Lu, Mingmei; Jiao, Shuo; Gao, Enting; Song, Xiuyong; Li, Zhefei; Hao, Xiuli; Rensing, Christopher; Wei, Gehong

2017-10-15

metal-contaminated soils. Considering the plant-growth-promoting traits and survival advantage of metal-resistant rhizobia in contaminated environments, more heavy metal-resistant rhizobia and genetically manipulated strains were investigated. In view of the genetic diversity of metal resistance determinants in rhizobia, their effects on phytoremediation by the rhizobium-legume symbiosis must be different and depend on their specific assigned functions. Our work provides a better understanding of the mechanism of heavy metal resistance determinants involved in the rhizobium-legume symbiosis, and in further studies, genetically modified rhizobia harboring effective heavy metal resistance determinants may be engineered for the practical application of rhizobium-legume symbiosis for bioremediation in metal-contaminated soils. Copyright © 2017 American Society for Microbiology.

Biofilm formation and antimicrobial sensitivity of lactobacilli contaminants from sugarcane-based fuel ethanol fermentation.

Science.gov (United States)

Dellias, Marina de Toledo Ferraz; Borges, Clóvis Daniel; Lopes, Mário Lúcio; da Cruz, Sandra Helena; de Amorim, Henrique Vianna; Tsai, Siu Mui

2018-02-24

Industrial ethanol fermentation is subject to bacterial contamination that causes significant economic losses in ethanol fuel plants. Chronic contamination has been associated with biofilms that are normally more resistant to antimicrobials and cleaning efforts than planktonic cells. In this study, contaminant species of Lactobacillus isolated from biofilms (source of sessile cells) and wine (source of planktonic cells) from industrial and pilot-scale fermentations were compared regarding their ability to form biofilms and their sensitivity to different antimicrobials. Fifty lactobacilli were isolated and the most abundant species were Lactobacillus casei, Lactobacillus fermentum and Lactobacillus plantarum. The majority of the isolates (87.8%) were able to produce biofilms in pure culture. The capability to form biofilms and sensitivity to virginiamycin, monensin and beta-acids from hops, showed inter- and intra-specific variability. In the pilot-scale fermentation, Lactobacillus brevis, L. casei and the majority of L. plantarum isolates were less sensitive to beta-acids than their counterparts from wine; L. brevis isolates from biofilms were also less sensitive to monensin when compared to the wine isolates. Biofilm formation and sensitivity to beta-acids showed a positive and negative correlation for L. casei and L. plantarum, respectively.

Release of hexachlorocyclohexanes from historically and freshly contaminated soils in China: Implications for fate and regulation

International Nuclear Information System (INIS)

Duan Lin; Zhang Nan; Wang Yu; Zhang Chengdong; Zhu Lingyan; Chen Wei

2008-01-01

Hexachlorocyclohexanes (HCHs) were produced and used in large quantity worldwide and are common soil pollutants. In this study, desorption of α-HCH and γ-HCH from two soil samples collected from a historical pesticide plant in Tianjin, China, was examined. As a comparison, desorption of freshly sorbed γ-HCH was examined, using five typical Chinese soils. Strong resistant desorption was observed for both historically contaminated and freshly contaminated soils, and desorption results were well modeled with a biphasic desorption isotherm. The unique thermodynamic characteristics associated with the desorption-resistant fraction indicated that physical constraint within soil organic matrices was likely the predominant mechanism controlling resistant desorption. Resistant desorption could have significant effects on fate and exposure of HCHs in soil environment. More accurate biphasic desorption models that take into account of the resistant desorption can be used to facilitate regulating, management and remediation of HCH-contaminated sites. - Resistant desorption of HCHs from both historically and freshly contaminated soils can be well predicted with a biphasic desorption model

Isolation of Lead Resistant Bacteria from Lead Contaminated Soil Samples Collected from Sundar Industrial Estate and their Potential Use in Bioremediation

International Nuclear Information System (INIS)

Saleem, F.; Adalat, R.; Munir, N.; Aftab, F.

2015-01-01

Industrial waste water pollution is one of the most controversial problem especially in countries like Pakistan. Human activities and the release of industrial waste have resulted the accumulation of metals in the environment. Noxious chemicals like heavy metals include cadmium, lead, chromium, copper, nickel, etc. that pollute the soils, ground water, sediments and surface waters re present in soluble form. Biosorpotion is a form of bioremediation by which metal ions are adsorbed from polluted site by microorganisms. Samples collected from industrial area were analyzed for lead contamination by Flame Atomic Spectrophotometer. Soil samples of Sundar Industrial Estate were highly resistant to different concentrations (300ppm, 800ppm, and 1600ppm) of Pb+2 whereas, the sample PbFa-458 showed maximum (127.9819mg/L) absorption of Pb+2, so can be used for environmental cleanup. From 24 selected lead resistant strains PbFa-136, PbFa-287, PbFa-960 showed resistance to multimetals, multidrug and high lead concentrations i.e 1800ppm, 2000ppm. Lead resistant strains were predicted as Klebsiella or Eenterobacter, Bacillus, Shigella, Salmonella and Enteroccocus. (author)

CAPABILITIES OF REMOTE SENSING HYPERSPECTRAL IMAGES FOR THE DETECTION OF LEAD CONTAMINATION: A REVIEW

Directory of Open Access Journals (Sweden)

A. A. Maliki

2012-07-01

Full Text Available Advances in remote sensing technologies are increasingly becoming more useful for resource, ecosystem and agricultural management applications to the extent that these techniques can now also be applied for monitoring of soil contamination and human health risk assessment. While, extensive previous studies have shown that Visible and Near Infrared Spectroscopy (VNIRS in the spectral range 400–2500 nm can be used to quantify various soil constituents simultaneously, the direct determination of metal concentrations by remote sensing and reflectance spectroscopy is not as well examined as other soil parameters. The application of VNIRS, including laboratory hyperpectral measurements, field spectrometer measurements or image spectroscopy, generally achieves a good prediction of metal concentrations when compared to traditional wet chemical methods and has the advantage of being relatively less expensive and faster, allowing chemical assessment of contamination in close to real time. Furthermore, imaging spectroscopy can potentially provide significantly more samples over a larger spatial extent than traditional ground sampling methods. Thus the development of remote sensing techniques (field based and either airborne or satellite hyperspectral imaging can support the monitoring and efficient mapping of metal contamination (in dust and soil for environmental and health impact assessment. This review is concerned with the application of remote sensing and reflectance spectroscopy to the detection of heavy metals and discusses how current methods could be applied for the quantification of Pb contaminated soil surrounding mines and smelters.

Use of nonpathogenic, green fluorescent protein-marked Escherichia coli Biotype I cultures to evaluate the self-cleansing capabilities of a commercial beef grinding system after a contamination event.

Science.gov (United States)

Wages, Jennifer A; Williams, Jennifer; Adams, Jacquelyn; George, Bruce; Oxford, Eric; Zelenka, Dan

2014-11-01

Inoculated beef trim containing a cocktail of green fluorescent protein-marked Escherichia coli biotype I cultures as surrogates for E. coli O157:H7 was introduced into two large, commercial grinding facilities capable of producing 180,000 kg of ground product in 1 day. Three repetitions were performed over 3 days. Sampling occurred at three different points within the process: postprimary grind, postsecondary grind-blender, and postpackaging. Resulting data show that, as the inoculated meat passes through the system, the presence of the marked surrogate quickly diminishes. The depletion rates are directly related to the amount of product in kilograms (represented by time) that has passed through the system, but these rates vary with each step of the process. The primary grinder appears to rid itself of the contaminant the most quickly; in all repetitions, the contaminant was not detected within 5 min of introduction of the contaminated combo bin into the system, which in all cases, was prior to the introduction of a second combo bin and within 1,800 kg of product. After the blending step and subsequent secondary grinding, the contaminant was detected in product produced from both the parent combo and the combo bin added directly after the parent combo bin; however, for those days on which three combo bins (approximately 2,700 kg) were available for sampling, the contaminant was not detected from product representing the third combo bin. Similarly, at the packaging step, the contaminant was detected in the product produced by both the parent and second combo bins; however, on those days when a third combo bin was available for sampling (repetitions 2 and 3), the contaminant was not detected from product produced from the third combo bin.

Capability and Mechanisms of Macrofungi in Heavy Metal Accumulation：A Review

Directory of Open Access Journals (Sweden)

CHEN Miao-miao

2017-10-01

Full Text Available Some macrofungi have the ability to accumulate heavy metals, which is comparable to hyper-accumulator plants. Cordyceps militaris can accumulate Zn up to 20 000 mg·kg-1. Therefore, macrofungi have the potential to be used as an important bioremediation tool for heavy metals. In this review, we summarized the heavy metal resistant capacity of typical macrofungi and known relevant mechanisms. Generally, straw-decay fungi presented better capability for Cu, Ag and Cd enrichment than wood-decay fungi, while wood-decay fungi could accumulate Cr, Mg, Se and Pb. Different macrofungi species, different growth periods(mycelium and fruiting body and different parts of fruiting body showed different capability for heavy metals accumulation. General mechanisms for heavy metals accumulation in macrofungi included extracellular precipitation in the forms of polymeric substances, cell wall adsorption and intracellular absorption. Macrofungi could also detoxify by chelating metal ions by metallothionein(MT, secreting antioxidant enzymes(SOD, CAT, POD and degradating the misfolded proteins by ubiquitin-proteasome system(UPS. We also explored the potential of macrofungi in heavy metal remediation and pollution diagnostics as a biological indicator. Some macrofungi had been applied in the remediation of heavy metal contaminated soils and water. Finally, some future research areas including strain breeding and genetic engineering were discussed, which might provide references for the future studies.

Copper Contamination Impairs Herbivore Initiation of Seaweed Inducible Defenses and Decreases Their Effectiveness.

Directory of Open Access Journals (Sweden)

Alexandria M Warneke

Full Text Available Seaweed-herbivore interactions are often mediated by environmental conditions, yet the roles of emerging anthropogenic stressors on these interactions are poorly understood. For example, chemical contaminants have unknown consequences on seaweed inducible resistance and herbivore response to these defenses despite known deleterious effects of contaminants on animal inducible defenses. Here, we investigated the effect of copper contamination on the interactions between a snail herbivore and a brown seaweed that displays inducible resistance to grazing. We examined seaweed inducible resistance and its effectiveness for organisms exposed to copper at two time points, either during induction or after herbivores had already induced seaweed defenses. Under ambient conditions, non-grazed tissues were more palatable than grazed tissues. However, copper additions negated the preference for non-grazed tissues regardless of the timing of copper exposure, suggesting that copper decreased both how herbivores initiated these inducible defenses and their subsequent effectiveness. Copper decreased stimulation of defenses, at least in part, by suppressing snail grazing pressure-the cue that turns inducible defenses on. Copper decreased effectiveness of defenses by preventing snails from preferentially consuming non-grazed seaweed. Thus, contaminants can potentially stress communities by changing seaweed-herbivore interactions mediated via inducible defenses. Given the ubiquity of seaweed inducible resistance and their potential influence on herbivores, we hypothesize that copper contamination may change the impact of these resistant traits on herbivores.

State Waste Discharge Permit Application: Electric resistance tomography testing

Energy Technology Data Exchange (ETDEWEB)

1994-04-01

This permit application documentation is for a State Waste Discharge Permit issued in accordance with requirements of Washington Administrative Code 173-216. The activity being permitted is a technology test using electrical resistance tomography. The electrical resistance tomography technology was developed at Lawrence Livermore National Laboratory and has been used at other waste sites to track underground contamination plumes. The electrical resistance tomography technology measures soil electrical resistance between two electrodes. If a fluid contaminated with electrolytes is introduced into the soil, the soil resistance is expected to drop. By using an array of measurement electrodes in several boreholes, the areal extent of contamination can be estimated. At the Hanford Site, the purpose of the testing is to determine if the electrical resistance tomography technology can be used in the vicinity of large underground metal tanks without the metal tank interfering with the test. It is anticipated that the electrical resistance tomography technology will provide a method for accurately detecting leaks from the bottom of underground tanks, such as the Hanford Site single-shell tanks.

State Waste Discharge Permit Application: Electric resistance tomography testing

International Nuclear Information System (INIS)

1994-04-01

This permit application documentation is for a State Waste Discharge Permit issued in accordance with requirements of Washington Administrative Code 173-216. The activity being permitted is a technology test using electrical resistance tomography. The electrical resistance tomography technology was developed at Lawrence Livermore National Laboratory and has been used at other waste sites to track underground contamination plumes. The electrical resistance tomography technology measures soil electrical resistance between two electrodes. If a fluid contaminated with electrolytes is introduced into the soil, the soil resistance is expected to drop. By using an array of measurement electrodes in several boreholes, the areal extent of contamination can be estimated. At the Hanford Site, the purpose of the testing is to determine if the electrical resistance tomography technology can be used in the vicinity of large underground metal tanks without the metal tank interfering with the test. It is anticipated that the electrical resistance tomography technology will provide a method for accurately detecting leaks from the bottom of underground tanks, such as the Hanford Site single-shell tanks

Bioremediation of contaminated soil: Strategy and case histories

International Nuclear Information System (INIS)

Balba, M.T.; Ying, A.C.; McNeice, T.G.

1991-01-01

Microorganisms are capable of degrading many kinds of xenobiotic compounds and toxic chemicals. These microorganisms are ubiquitous in nature and there are numerous cases in which long-term contamination of soil and groundwater has been observed. The persistence of the contamination is usually caused by the inability of micro-organisms to metabolize these compounds under the prevailing environmental conditions. Two general reasons account for the failure of microbes to degrade pollutants in any environment: (1) inherent molecular recalcitrance of the contaminants and (2) environmental factors. The inherent molecular recalcitrance is usually associated with xenobiotic compounds where the chemical structure of the molecule is such that microbes and enzymes required for its catabolism have not evolved yet in nature. The environmental factors include a range of physicochemical conditions which influence microbial growth and activity. Biological remediation of contaminated sites can be accomplished using naturally-occurring microorganisms to treat the contaminants. Only particular groups of microorganisms are capable of decomposing specific compounds. The development of a bioremediation program for a specific contaminated soil system usually includes: thorough site/soil/waste characterization; treatability studies; and design and implementation of the bioremediation plan. The results of in situ and ex situ treatment programs involving the cleanup of petroleum hydrocarbon-contaminated soil will be discussed in detail. The paper will address key issues affecting the success of the bioremediation process such as nutrient transport, metal precipitation and potential soil clogging, microbial inoculation, etc

Damage coefficient and defect level of copper-contaminated silicon N+P diode

International Nuclear Information System (INIS)

Usami, A.; Kato, Y.

1975-01-01

The damage coefficient at 298 0 K of copper-contaminated N + P diodes is smaller than that of non-contaminated ones. In these copper-contaminated samples, the higher the bulk resistivity is, the smaller is the damage coefficient. For non-contaminated diodes, the damage coefficient of samples of pulled bulk crystals is smaller than that of floating zone crystals, and the higher bulk resistivity diodes have smaller damage coefficient. At 217 0 K measurement, the effect of copper-contamination on the damage coefficient could not be observed. The energy levels of defects introduced by gamma ray irradiation are approximately0.30 eV, and approximately0.28 eV with non-contaminated FZ 135 ohm-cm and CZ 10 ohm-cm bulk samples, respectively. In copper-contaminated samples, approximately0.60 eV and approximately0.45 eV are obtained as the defect energy levels for FZ 135 ohm-cm and CZ 10 ohm-cm bulk samples. (U.S.)

Persistent environmental contamination with USA300 methicillin-resistant Staphylococcus aureus and other pathogenic strain types in households with S. aureus skin infections.

Science.gov (United States)

Eells, Samantha J; David, Michael Z; Taylor, Alexis; Ortiz, Nancy; Kumar, Neha; Sieth, Julia; Boyle-Vavra, Susan; Daum, Robert S; Miller, Loren G

2014-11-01

To understand the genotypic spectrum of environmental contamination of Staphylococcus aureus in households and its persistence. Prospective longitudinal cohort investigation. Index participants identified at 2 academic medical centers. Adults and children with S. aureus skin infections and their household contacts in Los Angeles and Chicago. Household fomites were surveyed for contamination at baseline and 3 months. All isolates underwent genetic typing. We enrolled 346 households, 88% of which completed the 3-month follow-up visit. S. aureus environmental contamination was 49% at baseline and 51% at 3 months. Among households with a USA300 methicillin-resistant S. aureus (MRSA) body infection isolate, environmental contamination with an indistinguishable MRSA strain was 58% at baseline and 63% at 3 months. Baseline factors associated with environmental contamination by the index subject's infection isolate were body colonization by any household member with the index subject's infection isolate at baseline (odds ratio [OR], 10.93 [95% confidence interval (CI), 5.75-20.79]), higher housing density (OR, 1.47 [95% CI, 1.10-1.96]), and more frequent household fomite cleaning (OR, 1.62 [95% CI, 1.16-2.27]). Household environmental contamination with the index subject's infection strain at 3 months was associated with USA300 MRSA and a synergistic interaction between baseline environmental contamination and body colonization by any household member with the index subject's infection strain. We found that infecting S. aureus isolates frequently persisted environmentally in households 3 months after skin infection. Presence of pathogenic S. aureus strain type in the environment in a household may represent a persistent reservoir that places household members at risk of future infection.

Current limiting capability of diffused resistors

International Nuclear Information System (INIS)

Shedd, W.; Cappelli, J.

1979-01-01

An experimental evaluation of the current limiting capability of dielectrically isolated diffused resistors at transient ionizing dose rates up to 6*10 12 rads(Si)/sec is presented. Existing theoretical predictions of the transient response of diffused resistors are summarized and compared to the experimentally measured values. The test resistors used allow the effects of sheet resistance and geometry on the transient response to be determined. The experimental results show that typical dielectrically isolated diffused resistors maintain adequate current limiting capability for use in radiation hardened integrated circuits

Surface Contaminant Control Technologies to Improve Laser Damage Resistance of Optics

Directory of Open Access Journals (Sweden)

Xiaofeng Cheng

2014-01-01

Full Text Available The large high-power solid lasers, such as the National Ignition Facility (NIF of America and the Shenguang-III (SG-III laser facility of China, can output over 2.1 MJ laser pulse for the inertial confinement fusion (ICF experiments. Because of the enhancement of operating flux and the expansion of laser driver scale, the problem of contamination seriously influences their construction period and operation life. During irradiation by intense laser beams, the contaminants on the metallic surface of beam tubes can be transmitted to the optical surfaces and lead to damage of optical components. For the high-power solid-state laser facilities, contamination control focuses on the slab amplifiers, spatial filters, and final-optical assemblies. In this paper, an effective solution to control contaminations including the whole process of the laser driver is put forward to provide the safe operation of laser facilities, and the detailed technical methods of contamination control such as washing, cleanliness metrology, and cleanliness protecting are also introduced to reduce the probability of laser-induced damage of optics. The experimental results show that the cleanliness level of SG-III laser facility is much better to ensure that the laser facility can safely operate at high energy flux.

Results of polarization resistance and impedance of steel bars embedded in carbonated concrete contaminated with chlorides

International Nuclear Information System (INIS)

Andrade, C.; Alonso, C.; Gonzalez, J.A.

1989-01-01

Laboratory results of the corrosion rate of steel embedded in carbonated concrete contaminated with chlorides determined through the Polarization Resistance method are presented here as examples of the possibilities offered by this technique in order to monitor the reinforcement corrosion process. The Rp technique has the advantages of fast response, simple and relatively accurate. Contrasts with gravimetric losses are presented. The A.C. Impedance measurements determined on the same specimens are also presented. The difficulties found in the interpretation of the results are stressed. R T values cannot easily be obtained. Several electrical circuits which may model the behaviour of the steel/concrete system are discussed. Finally, comments on the basic criteria to interpret results of both techniques are given. (author) 4 refs., 6 figs

Oral chlorhexidine and microbial contamination during endoscopy

DEFF Research Database (Denmark)

Donatsky, Anders Meller; Holzknecht, Barbara Juliane; Arpi, Magnus

2013-01-01

BACKGROUND: One of the biggest concerns associated with transgastric surgery is contamination and risk of intra-abdominal infection with microbes introduced from the access route. The purpose of this study was to evaluate the effect of oral decontamination with chlorhexidine on microbial contamin......BACKGROUND: One of the biggest concerns associated with transgastric surgery is contamination and risk of intra-abdominal infection with microbes introduced from the access route. The purpose of this study was to evaluate the effect of oral decontamination with chlorhexidine on microbial...... contamination of the endoscope. METHODS: In a prospective, randomized, single-blinded, clinical trial the effect of chlorhexidine mouth rinse was evaluated. As a surrogate for the risk of intra-abdominal contamination during transgastric surgery, microbial contamination of the endoscope during upper endoscopy...... microbial contamination of the endoscope, but micro-organisms with abscess forming capabilities were still present. PPI treatment significantly increased CFU and should be discontinued before transgastric surgery....

Characterization of arsenite-oxidizing bacteria isolated from arsenic-contaminated groundwater of West Bengal.

Science.gov (United States)

Paul, Dhiraj; Poddar, Soumya; Sar, Pinaki

2014-01-01

Nine arsenic (As)-resistant bacterial strains isolated from As-rich groundwater samples of West Bengal were characterized to elucidate their potential in geomicrobial transformation and bioremediation aspects. The 16S rRNA gene-based phylogenetic analysis revealed that the strains were affiliated with genera Actinobacteria, Microbacterium, Pseudomonas and Rhizobium. The strains exhibited high resistance to As [Minimum inhibitory concentration (MIC) ≥ 10 mM As(3+) and MIC ≥ 450 mM As(5+)] and other heavy metals, e.g., Cu(2+), Cr(2+), Ni(2+), etc. (MIC ≥ 2 mM) as well as As transformation (As(3+) oxidation and As(5+) reduction) capabilities. Their ability to utilize diverse carbon source(s) including hydrocarbons and different alternative electron acceptor(s) (As(5+), SO4(2-), S2O3(2-), etc.) during anaerobic growth was noted. Growth at wide range of pH, temperature and salinity, production of siderophore and biofilm were observed. Together with these, growth pattern and transformation kinetics indicated a high As(3+) oxidation activity of the isolates Rhizobium sp. CAS934i, Microbacterium sp. CAS905i and Pseudomonas sp. CAS912i. A positive relation between high As(3+) resistance and As(3+) oxidation and the supportive role of As(3+) in bacterial growth was noted. The results highlighted As(3+) oxidation process and metabolic repertory of strains indigenous to contaminated groundwater and indicates their potential in As(3+) detoxification. Thus, such metabolically well equipped bacterial strains with highest As(3+) oxidation activities may be used for bioremediation of As contaminated water and effluents in the near future.

Antibiotic resistance in Escherichia coli isolates from roof-harvested rainwater tanks and urban pigeon faeces as the likely source of contamination.

Science.gov (United States)

Chidamba, Lizyben; Korsten, Lise

2015-07-01

The objective of this study was to investigate the risks associated with the use of roof-harvested rainwater (RHRW) and the implication of pigeons as the most likely source of contamination by testing for antibiotic resistance profiles of Escherichia coli. A total of 239 E. coli were isolated from thirty fresh pigeon faecal samples (130 isolates), 11 RHRW tanks from three sites in Pretoria (78) and two in Johannesburg (31). E. coli isolates were tested against a panel of 12 antibiotics which included ampicillin, amoxicillin, amikacin, cefoxitin, ceftriaxone, chloramphenicol, ciprofloxacin, cotrimoxazole, enrofloxacin, gentamicin, nalidixic acid and tetracycline. In all samples, resistance to ampicillin (22.7.9%), gentamicin (23.6%), amikacin (24%), tetracycline (17.4) and amoxicillin (16.9%) were the most frequently encountered form of resistance. However, a relatively higher proportion of isolates from pigeon faeces (67.3%) were antibiotic resistant than those from RHRW (53.3%). The highest number of phenotypes was observed for single antibiotics, and no single antibiotic resistance was observed for chloramphenicol, ceftriaxone, gentamicin, cefoxitin, cotrimoxazole, although they were detected in multiple antibiotic resistance (MAR) phenotypes. The highest multiple antibiotic resistance (MAR) phenotypes were observed for a combination of four antibiotics, on isolates from JHB (18.8%), pigeon faeces (15.2%) and Pretoria (5.1%). The most abundant resistance phenotype to four antibiotics, Ak-Gm-Cip-T was dominated by isolates from pigeon faeces (6.8%) with Pretoria and Johannesburg isolates having low proportions of 1.3 and 3.1%, respectively. Future studies should target isolates from various environmental settings in which rainwater harvesting is practiced and the characterisation of the antibiotic resistance determinant genes among the isolates.

Radioactive contamination incidents involving protective clothing

International Nuclear Information System (INIS)

Reichelt, R.A.; Clay, M.E.; Eichorst, A.J.

1998-01-01

The study focuses on incidents at Department of Energy facilities involving the migration of radioactive contaminants through protective clothing. The authors analyzed 68 occurrence reports for the following factors: (1) type of work, (2) working conditions, (3) type of anti-contamination material; (4) area of body or clothing contaminated; and (5) nature of spread of contamination. A majority of reports identified strenuous work activities such as maintenance, construction, or decontamination and decommissioning projects. The reports also indicated adverse working conditions that included hot and humid or cramped work environments. The type of anti-contamination clothing most often identified was cotton or water-resistant disposable clothing. Most of the reports also indicated contaminants migrating through perspiration-soaked areas, typically in the knees and forearms. On the basis of their survey, the authors recommend the use of improved engineering controls and resilient, breathable, waterproof protective clothing for work in hot, humid, or damp areas where the possibility of prolonged contact with contamination cannot be easily avoided or controlled. 1 ref., 6 figs., 1 tab

Antibiotic Resistant Bacteria And Their Associated Resistance Genes in a Conventional Municipal Wastewater Treatment Plant

KAUST Repository

Aljassim, Nada I.

2013-12-01

With water scarcity as a pressing issue in Saudi Arabia and other Middle Eastern countries, the treatment and reuse of municipal wastewater is increasingly being used as an alternative water source to supplement country water needs. Standards are in place to ensure a safe treated wastewater quality, however they do not regulate pathogenic bacteria and emerging contaminants. Information is lacking on the levels of risk to public health associated with these factors, the efficiency of conventional treatment strategies in removing them, and on wastewater treatment in Saudi Arabia in general. In this study, a municipal wastewater treatment plant in Saudi Arabia is investigated to assess the efficiency of conventional treatment in meeting regulations and removing pathogens and emerging contaminants. The study found pathogenic bacterial genera, antibiotic resistance genes and antibiotic resistant bacteria, many of which were multi-resistant in plant discharges. It was found that although the treatments are able to meet traditional quality guidelines, there remains a risk from the discussed contaminants with wastewater reuse. A deeper understanding of this risk, and suggestions for more thorough guidelines and monitoring are needed.

Relationship between resist outgassing and EUV witness sample contamination in NXE outgas qualification using electrons and EUV photons

Science.gov (United States)

Pollentier, I.; Tirumala Venkata, A.; Gronheid, R.

2014-04-01

EUV photoresists are considered as a potential source of optics contamination, since they introduce irradiation-induced outgassing in the EUV vacuum environment. Therefore, before these resists can be used on e.g. ASML NXE:3100 or NXE:3300, they need to be tested in dedicated equipment according to a well-defined procedure, which is based on exposing a witness sample (WS) in the vicinity of a simultaneously exposed resist as it outgasses. Different system infrastructures are used at multiple sites (e.g. NIST, CNSE, Sematech, EIDEC, and imec) and were calibrated to each other by a detailed test plan. Despite this detailed tool qualifications, a first round robin comparison of identical materials showed inconsistent outgas test results, and required further investigation by a second round robin. Since the resist exposure mode is different at the various locations (some sites are using EUV photons while others use E-gun electrons), this difference has always a point of concern for variability of test results. In this work we compare the outgas test results from EUV photon and electron exposure using the resist materials of the second round robin. Since the imec outgas tester allows both exposure methods on the resist, a within-system comparison is possible and showed limited variation between photon and electron exposure mode. Therefore the system-to-system variability amongst the different outgas test sites is expected to be related to other parameters than the electron/photon exposure mode. Initial work showed that the variability might be related to temperature, E-gun emission excursion, and/or residual outgassing scaled by different wafer areas at the different sites.

Frequency of legionella contamination in conditional & water distribution systems of Tehran hospitals

Directory of Open Access Journals (Sweden)

Davod Esmaieli

2008-09-01

Full Text Available Background: Legionella species are ubiquitous in natural aquatic environments, capable of existing in waters with varied temperatures, PH levels, and nutrient and oxygen contents. Of 49 known legionella species, 20 species have been linked to pneumonia in humans. Contamination by legionella has occurred in the distribution systems of many hospitals. Aerosol-generating systems such as faucets, showerheads, cooling towers, and nebulizers are responsible for their transmission from water to air. Methods: A total of 113 water samples were gathered from different wards of 32 hospitals in different geographical regions of Tehran city. These samples were concentrated by filtration, treated with the acid and temperature buffers, and isolated on a BCYE agar culture medium. Results: A total of 22 hospitals out of 33 (26.5% were contaminated by legionella species, and 30 samples (26.5% out of 113 were positive. Chlorine concentration and pH level of the water samples were 0.18-2.2 mg/l and 6.6-7.6, respectively. Conclusion: The high rate of waste water contamination in Tehran hospitals with Legionella indicates the resistance of this microorganism to chlorine and other disinfectants, or inadequate disinfection process, representing the insufficiency of the current decontamination of hospital water distribution system. Thus identifying legionella species and their controlling in water distribution system of hospitals is of great importance.

Superconductive microstrip exhibiting negative differential resistivity

International Nuclear Information System (INIS)

Huebener, R.P.; Gallus, D.E.

1975-01-01

A device capable of exhibiting negative differential electrical resistivity over a range of values of current and voltage is formed by vapor-depositing a thin layer of a material capable of exhibiting superconductivity on an insulating substrate, establishing electrical connections at opposite ends of the deposited strip, and cooling the alloy into its superconducting range. The device will exhibit negative differential resistivity when biased in the current-induced resistive state

In silico exploration of the impact of pasture larvae contamination and anthelmintic treatment on genetic parameter estimates for parasite resistance in grazing sheep.

Science.gov (United States)

Laurenson, Y C S M; Kyriazakis, I; Bishop, S C

2012-07-01

A mathematical model was developed to investigate the impact of level of Teladorsagia circumcincta larval pasture contamination and anthelmintic treatment on genetic parameter estimates for performance and resistance to parasites in sheep. Currently great variability is seen for published correlations between performance and resistance, with estimates appearing to vary with production environment. The model accounted for host genotype and parasitism in a population of lambs, incorporating heritable between-lamb variation in host-parasite interactions, with genetic independence of input growth and immunological variables. An epidemiological module was linked to the host-parasite interaction module via food intake (FI) to create a grazing scenario. The model was run for a population of lambs growing from 2 mo of age, grazing on pasture initially contaminated with 0, 1,000, 3,000, or 5,000 larvae/kg DM, and given either no anthelmintic treatment or drenched at 30-d intervals. The mean population values for FI and empty BW (EBW) decreased with increasing levels of initial larval contamination (IL(0)), with non-drenched lambs having a greater reduction than drenched ones. For non-drenched lambs the maximum mean population values for worm burden (WB) and fecal egg count (FEC) increased and occurred earlier for increasing IL(0), with values being similar for all IL(0) at the end of the simulation. Drenching was predicted to suppress WB and FEC, and cause reduced pasture contamination. The heritability of EBW for non-drenched lambs was predicted to be initially high (0.55) and decreased over time with increasing IL(0), whereas drenched lambs remained high throughout. The heritability of WB and FEC for all lambs was initially low (∼0.05) and increased with time to ∼0.25, with increasing IL(0) leading to this value being reached at faster rates. The genetic correlation between EBW and FEC was initially ∼-0.3. As time progressed the correlation tended towards 0, before

Advance simulation capability for environmental management (ASCEM) - 59065

International Nuclear Information System (INIS)

Dixon, Paul; Keating, Elizabeth; Moulton, David; Williamson, Mark; Collazo, Yvette; Gerdes, Kurt; Freshley, Mark; Gorton, Ian; Meza, Juan

2012-01-01

The United States Department Energy (DOE) Office of Environmental Management (EM) determined that uniform application of advanced modeling in the subsurface could help reduce the cost and risks associated with its environmental cleanup mission. In response to this determination, the EM Office of Technology Innovation and Development (OTID), Groundwater and Soil Remediation (GW and S) began the program Advanced Simulation Capability for Environmental Management (ASCEM). ASCEM is a state-of-the-art scientific tool and approach for integrating data and scientific understanding to enable prediction of contaminant fate and transport in natural and engineered systems. This initiative supports the reduction of uncertainties and risks associated with EM?s environmental cleanup and closure programs through better understanding and quantifying the subsurface flow and contaminant transport behavior in complex geological systems. This involves the long-term performance of engineered components, including cementitious materials in nuclear waste disposal facilities that may be sources for future contamination of the subsurface. This paper describes the ASCEM tools and approach and the ASCEM programmatic accomplishments completed in 2010 including recent advances and technology transfer. The US Department of Energy Office of Environmental Management has begun development of an Advanced Simulation Capability for Environmental Management, (ASCEM). This program will provide predictions of the end states of contaminated areas allowing for cost and risk reduction of EM remedial activities. ASCEM will provide the tools and approaches necessary to standardize risk and performance assessments across the DOE complex. Through its Phase One demonstration, the ASCEM team has shown value to the EM community in the areas of High Performance Computing, Data Management, Visualization, and Uncertainty Quantification. In 2012, ASCEM will provide an initial limited release of a community code for

REDUCTIVE DEHALOGENATION OF ORGANIC CONTAMINANTS IN SOILS AND GROUND WATER

Science.gov (United States)

Introduction and large scale production of synthetic halogenated organic chemicals over the last 50 years has resulted in a group of contaminants which tend to persist in the environment and resist both biotic and abiotic degradation. The low solubility of these types of contamin...

Microbial functional genes enriched in the Xiangjiang River sediments with heavy metal contamination.

Science.gov (United States)

Jie, Shiqi; Li, Mingming; Gan, Min; Zhu, Jianyu; Yin, Huaqun; Liu, Xueduan

2016-08-08

Xiangjiang River (Hunan, China) has been contaminated with heavy metal for several decades by surrounding factories. However, little is known about the influence of a gradient of heavy metal contamination on the diversity, structure of microbial functional gene in sediment. To deeply understand the impact of heavy metal contamination on microbial community, a comprehensive functional gene array (GeoChip 5.0) has been used to study the functional genes structure, composition, diversity and metabolic potential of microbial community from three heavy metal polluted sites of Xiangjiang River. A total of 25595 functional genes involved in different biogeochemical processes have been detected in three sites, and different diversities and structures of microbial functional genes were observed. The analysis of gene overlapping, unique genes, and various diversity indices indicated a significant correlation between the level of heavy metal contamination and the functional diversity. Plentiful resistant genes related to various metal were detected, such as copper, arsenic, chromium and mercury. The results indicated a significantly higher abundance of genes involved in metal resistance including sulfate reduction genes (dsr) in studied site with most serious heavy metal contamination, such as cueo, mer, metc, merb, tehb and terc gene. With regard to the relationship between the environmental variables and microbial functional structure, S, Cu, Cd, Hg and Cr were the dominating factor shaping the microbial distribution pattern in three sites. This study suggests that high level of heavy metal contamination resulted in higher functional diversity and the abundance of metal resistant genes. These variation therefore significantly contribute to the resistance, resilience and stability of the microbial community subjected to the gradient of heavy metals contaminant in Xiangjiang River.

Antibiotic resistance of microorganisms in agricultural soils in Russia

Science.gov (United States)

Danilova, N. V.; Galitskaya, P. Yu; Selivanovskaya, S. Yu

2018-01-01

Antibiotics are medicines that are widely used in livestock production not only for the prevention and treatment of infectious diseases, but also for accelerating the growth of animals. The application of manure for fertilizing agricultural soils leads to the entry into the soil ecosystem not only of the antibiotics themselves, but also the resistance genes to them. In this study, 30 samples of arable soils were tested for the presence of the tet(X) gene, which encodes bacterial resistance to antibiotics of the tetracycline group. Using real-time PCR, it was found that 27 out of 30 soil samples contained tet(X). 52% of these samples were heavily contaminated, 34% had a medium level of contamination and 14% were slightly contaminated by the resistance gene tet(X).

Influence of fertilization on the capability of rice resistance to diseases

Science.gov (United States)

Hu, Xue-Feng; Chang, Yue-Ya; Jiang, Ying; Yan, Xiao-Juan; Luo, Fan

2013-04-01

Organic cultivation of rice requires no use of any agricultural chemicals during the entire period of growth, and so the rice's self-prevention of diseases and pests is vitally important. A field experiment was carried out to study the possible influence of different fertilization on the capability of rice resistance to diseases and pests. A rice variety used for this experiment is Jia-He 218. Four treatments (A, B, C and D) were designed: A is a control, without using any fertilizers; B, after manuring of green azolla, 0.67 kg/m2; C, after manuring of rapeseed cake, 0.30 kg/m2; D, after fertilizing of ammonium bicarbonate, 0.025 kg/m2, and urea, 0.025 kg/m2. The experiment plot is 66.7 m2, with three replicates. The results indicated that the fertilization patterns significantly influence the growth of rice seedlings: The heights by A, B, C and D are 37 cm, 40 cm , 42 cm and 45 cm on average, respectively; the spike numbers, 45, 65, 73 and 75, respectively; chlorophyll contents in leaves, 1.84 mg/g, 2.42 mg/g, 3.02 mg/g and 3.97 mg/g, respectively. The rice with the different fertilization also varies in nutrient concentration in leaves: NH4-N concentration in leaves by A, B, C and D is 47.5 mg/kg, 61.1 mg/kg, 74.7 mg/kg and 135.8 mg/kg on average, respectively; NO3-N in leaves, 138.9 mg/kg, 185.2 mg/kg, 154.3 mg/kg and 293.2 mg/kg, respectively. The fertilization patterns, moreover, show a significant influence on the incidence of diseases and pests to rice seedlings: The incidence of rice cnaphalocrocis medinalis by A, B, C and D is 1.33 %, 1.50 %, 1.75 % and 89.0 % on average, respectively; that of bacterial leaf blight, 0, 1.25 %, 1.75 % and 85.0 %, respectively; number of rice planthopper in each plant, 20, 21, 21 and 30, respectively. As a result, the yield of rice grain by A, B, C and D is 4540 kg/ha, 4606 kg/ha, 4503 kg/ha and 4092 kg/ha on average, respectively. In conclusion, the rice seedlings treated with chemical fertilizers grow large and tender

Cemaran Escherichia coli pada Tepung Telur yang Diimpor Melalui Pelabuhan Tanjung Priok, dan Resistensinya Terhadap Antibiotik (ESCHERICHIA COLI CONTAMINATION ON EGG POWDER IMPORTED THROUGH PORT OF TANJUNG PRIOK AND ITS RESISTANCE AGAINST ANTIBIOTICS

Directory of Open Access Journals (Sweden)

Kamil Riski Sidik

2016-07-01

Full Text Available Eschericia coli contamination was found on egg powder imported to Indonesia during microbialexamination. The study was conducted to describe the presence of E. coli and its resistance to antibioticsin egg powder imported to Indonesia through The port of Tanjung Priok. Samples was determined usingcross sectional study and the sample size was calculated based on assumption of confidence level of 95%with margin of error of 10% and predicted prevalence of 50%. Total of 100 egg powder samples wascollected in August 2014 from two exporting countries, Ukraine (whole egg powder, n=30 and India (wholeegg powder, n=40 and egg yolk powder, n=30. Examination was performed by packaging and label inspectionof the product followed by samples collection and testing for bacterial contamination using rapid test andconventional isolation and identification methods. Detected E. coli was isolated and then tested forantibiotic resistance. Examination results showed that 4 samples were positive to E. coli. E. coli isolatesshowed resistance against 6 types of antibiotics and 75% of the isolates had resistance against minimumof 3 types of antibiotics. These conditions should be taken into consideration since antibiotic resistance inE. coli would cause negative impacts on human, animal and environmental health.

A system for the study of molecular contamination. [experimental vacuum chambers

Science.gov (United States)

Dillow, C. F.; Allen, T. H.; Linford, R. M. F.; Richmond, R. G.

1975-01-01

An experimental vacuum chambers was designed and fabricated to provide a wide range of experimental capability. This work chamber assembly (WCA) was conceived to establish the proof-of-principle of various techniques for studying the kinetics of contaminants and their effects. It incorporates the capability for depositing both optical and contaminant films on temperature-controlled samples, and for in-situ measurements of the vacuum ultraviolet reflectance. Ellipsometer optics are mounted on the chamber for film thickness determinations, and other features include access ports for radiation sources and instrumentation.

Radioactive contamination incidents involving protective clothing

Energy Technology Data Exchange (ETDEWEB)

Reichelt, R.; Clay, M.; Eichorst, J.

1996-10-01

The study focuses on incidents at Department of Energy (DOE) facilities involving the migration of radioactive contaminants through protective clothing. The authors analyzed 68 occurrence reports for the following factors: (1) type of work; (2) working conditions; (3) type of anti-contamination (anti-C) material; (4) area of body or clothing contaminated; and (5) nature of spread of contamination. A majority of reports identified strenuous work activities such as maintenance, construction, or decontamination and decommissioning (D&D) projects. The reports also indicated adverse working conditions that included hot and humid or cramped work environments. The type of anti-C clothing most often identified was cotton or water-resistant, disposable clothing. Most of the reports also indicated contaminants migrating through perspiration-soaked areas, typically in the knees and forearms. On the basis of their survey, the authors recommend the use of improved engineering controls and resilient, breathable, waterproof protective clothing for work in hot, humid, or damp areas where the possibility of prolonged contact with contamination cannot be easily avoided or controlled.

Radioactive contamination incidents involving protective clothing

International Nuclear Information System (INIS)

Reichelt, R.; Clay, M.; Eichorst, J.

1996-10-01

The study focuses on incidents at Department of Energy (DOE) facilities involving the migration of radioactive contaminants through protective clothing. The authors analyzed 68 occurrence reports for the following factors: (1) type of work; (2) working conditions; (3) type of anti-contamination (anti-C) material; (4) area of body or clothing contaminated; and (5) nature of spread of contamination. A majority of reports identified strenuous work activities such as maintenance, construction, or decontamination and decommissioning (D ampersand D) projects. The reports also indicated adverse working conditions that included hot and humid or cramped work environments. The type of anti-C clothing most often identified was cotton or water-resistant, disposable clothing. Most of the reports also indicated contaminants migrating through perspiration-soaked areas, typically in the knees and forearms. On the basis of their survey, the authors recommend the use of improved engineering controls and resilient, breathable, waterproof protective clothing for work in hot, humid, or damp areas where the possibility of prolonged contact with contamination cannot be easily avoided or controlled

Isolation and characterization of aerobic culturable arsenic-resistant bacteria from surfacewater and groundwater of Rautahat District, Nepal.

Science.gov (United States)

Shakya, S; Pradhan, B; Smith, L; Shrestha, J; Tuladhar, S

2012-03-01

Arsenic (As) contamination of groundwater is a serious Environmental Health Management issue of drinking water sources especially in Terai region of Nepal. Many studies have reported that due to natural abundance of arsenic in the environment, various bacteria have developed different resistance mechanisms for arsenic compound. In this study, the culturable arsenic-resistant bacteria indigenous to surfacewater as well as groundwater from Rautahat District of Nepal were randomly isolated by standard plate count method on the basis of viable growth on plate count agar amended with arsenate ranging from 0, 0.5, 10, 40, 80 to 160 milligram per liter (mg/l). With respect to the morphological and biochemical tests, nine morphologically distinct potent arsenate tolerant bacteria showed relatedness with Micrococcus varians, Micrococcus roseus, Micrococcus luteus, Pseudomonas maltophilia, Pseudomonas sp., Vibrio parahaemolyticus, Bacillus cereus, Bacillus smithii 1 and Bacillus smithii 2. The isolates were capable of tolerating more than 1000 mg/l of arsenate and 749 mg/l of arsenite. Likewise, bioaccumulation capability was highest with M. roseus (85.61%) and the least with B. smithii (47.88%) indicating the potential of the organisms in arsenic resistance and most probably in bioremediation. Copyright © 2011 Elsevier Ltd. All rights reserved.

Contaminant and other elements in soil (CCQM-K127)

Science.gov (United States)

Rocio Arvizu Torres, M.; Manzano, J. Velina Lara; Valle Moya, Edith; Horvat, Milena; Jaćimović, Radojko; Zuliani, Tea; Vreča, Polona; Acosta, Osvaldo; Bennet, John; Snell, James; Almeida, Marcelo D.; de Sena, Rodrigo C.; Dutra, Emily S.; Yang, Lu; Li, Haifeng

2017-01-01

Non-contaminated soils contain trace and major elements at levels representing geochemical background of the region. The main sources of elements as contaminants/pollutants in soils are mining and smelting activities, fossil fuel combustion, agricultural practices, industrial activities and waste disposal. Contaminated/polluted sites are of great concern and represent serious environmental, health and economic problems. Characterization and identification of contaminated land is the first step in risk assessment and remediation activities. It is well known that soil is a complex matrix with huge variation locally and worldwide. According to the IAWG's five year plan, it is recommended to have a key comparison under the measurement service category of soils and sediments for the year 2015. Currently 13 NMI has claimed calibration and measurement capabilities (CMCs) in category 13 (sediments, soils, ores, and particulates): 29 CMCs in soil and 96 CMCs in sediments. In this regard this is a follow-up comparison in the category 13; wherein three key comparisons have been carried out during the years 2000 (CCQM-K13), 2003 (CCQM-K28) and 2004 (CCQM-K44). Since it is important to update the capabilities of NMIs in this category. CENAM and JSI proposed a key comparison in this category and a pilot study in parallel. The proposed study was agreed by IAWG members, where two soils samples were used in both CCQM-K127 representing a non-contaminated soil with low contents of elements (arsenic, cadmium, iron, lead and manganese), and a contaminated soil with much higher content of selected elements (arsenic, cadmium, iron and lead). This broadens the scope and a degree of complexity of earlier measurements in this field. National metrology institutes (NMIs)/designate institutes (DIs) should, therefore, demonstrate their measurement capabilities of trace and major elements in a wide concentration ranges, representing background/reference sites as well as highly contaminated soils

A meta-analysis of the rates of Staphylococcus aureus and methicillin-resistant S aureus contamination on the surfaces of environmental objects that health care workers frequently touch.

Science.gov (United States)

Lin, Dongxin; Ou, Qianting; Lin, Jialing; Peng, Yang; Yao, Zhenjiang

2017-04-01

Health care workers may potentially spread Staphylococcus aureus and methicillin-resistant S aureus (MRSA) to patients by contaminated high-touch items. We aimed to determine the pooled rates of S aureus and MRSA contamination and influencing factors. A literature search of the PubMed, ScienceDirect, Embase, Ovid, and Scopus databases was performed. Pooled contamination rates were determined using random effect models. Subgroup and meta-regression analyses were conducted to identify factors potentially influencing the rates of S aureus and MRSA contamination. Sensitivity and publication bias analyses were performed. Thirty-eight studies were included in the meta-analysis. The pooled contamination rates were 15.0% (95% confidence interval [CI], 9.8%-21.1%) for S aureus and 5.0% (95% CI, 2.7%-7.7%) for MRSA. The subgroup analyses indicated that the pooled rate of S aureus contamination was significantly higher for studies conducted in South America, in developing countries, and during 2010-2015. The pooled rate of MRSA contamination was significantly higher for studies conducted in Africa. The meta-regression analysis suggested that the pooled rate of S aureus contamination was lower for studies conducted in developed countries (odds ratio, 0.664; 95% CI, 0.509-0.867; P = .004). No bias was found in the publication of the rates of S aureus and MRSA contamination. S aureus and MRSA contamination statuses of high-touch items are worrisome and should be paid greater attention. Developing country status was a risk factor for S aureus contamination. Copyright © 2017 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Elsevier Inc. All rights reserved.

Biological indicators capable of assessing thermal treatment efficiency of hydrocarbon mixture-contaminated soil.

Science.gov (United States)

Wang, Jiangang; Zhan, Xinhua; Zhou, Lixiang; Lin, Yusuo

2010-08-01

In China, there are many special sites for recycling and washing the used drums, which release a variety of C5-C40 hydrocarbon mixture into the soil around the site. The remediation of these contaminated sites by thermal treatment is adopted ubiquitously and needs to be assessed. Here we report the feasibility of biological indicators applied to assess thermal treatment efficiency in such contaminated soil. A series of biological indicators, including seed germination index (SGI), root elongation index (REI), plant growth height, biomass, carbon dioxide evolved (CDE), soil respiration inhibition (SRI) and soil enzymatic activities, were employed to monitor or assess hydrocarbon mixture removal in thermal treated soil. The results showed that residual hydrocarbon mixture content correlated strongly negatively with SGI for sesamum (Sesamum indicum L.), plant height, and biomass for ryegrass (Lolium perenne L.) in the concentration ranges of 0-3990, 0-3170 and 0-2910 mg kg(-1), respectively. In contrast, REI for sesamum was positively correlated with residual hydrocarbon mixture content from 0 to 1860 mg kg(-1). In addition, both CDE and SRI demonstrated that 600 mg kg(-1) of residual hydrocarbon mixture content caused the highest amount of soil carbon dioxide emission and inhabitation of soil respiration. The results of soil enzymes indicated that 1000 mg kg(-1) of residual hydrocarbon mixture content was the threshold value of stimulating or inhibiting the activities of phosphatase and catalase, or completely destroying the activities of dehydrogenase, invertase, and urease. In conclusion, these biological indicators can be used as a meaningful complementation for traditional chemical content measurement in evaluating the environmental risk of the contaminated sites before and after thermal treatment. (c) 2010 Elsevier Ltd. All rights reserved.

Remediation of lead-contaminated soils

International Nuclear Information System (INIS)

Peters, R.W.; Shem, L.

1992-01-01

Excavation and transport of soil contaminated with heavy metals has generally been the standard remediation technique for treatment of heavy-metal-contaminated soils. This approach is not a permanent solution; moreover, off-site shipment and disposal of contaminated soil involves high expense, liability, and appropriate regulatory approval. Recently, a number of other techniques have been investigated for treating such contaminated sites, including flotation, solidification/stabilization, vitrification, and chemical extraction. This paper reports the results of a laboratory investigation determining the efficiency of using chelating agents to extract lead from contaminated soils. Lead concentrations in the soils ranged from 500 to 10,000 mg/kg. Ethylenediaminetetraacetic acid (EDTA) and nitrilotriacetic acid (NTA) were examined for their potential extractive capabilities. Concentrations of the chelating agents ranged from 0.01 to 0.10 M. The pH of the suspensions in which the extractions were performed ranged from 4 to 12. Results showed that the removal of lead using NTA and water was ph-dependent, whereas the removal of lead using EDTA was ph-insensitive. Maximum removals of lead were 68.7%,19.1%, and 7.3% using EDTA, NTA, and water, respectively (as compared with initial lead concentrations)

Sphingomonas from petroleum-contaminated soils in Shenfu, China and their PAHs degradation abilities

Directory of Open Access Journals (Sweden)

Lisha Zhou

2016-06-01

Full Text Available Abstract Members of the Sphingomonas genus are often isolated from petroleum-contaminated soils due to their unique abilities to degrade polycyclic aromatic hydrocarbons (PAHs, which are important for in situ bioremediation. In this study, a combined phenotypic and genotypic approach using streptomycin-containing medium and Sphingomonas -specific PCR was developed to isolate and identify culturable Sphingomonas strains present in petroleum-contaminated soils in the Shenfu wastewater irrigation zone. Of the 15 soil samples examined, 12 soils yielded yellow streptomycin-resistant colonies. The largest number of yellow colony-forming units (CFUs could reach 105 CFUs g-1 soil. The number of yellow CFUs had a significant positive correlation (p < 0.05 with the ratio of PAHs to total petroleum hydrocarbons (TPH, indicating that Sphingomonas may play a key role in degrading the PAH fraction of the petroleum contaminants at this site. Sixty yellow colonies were selected randomly and analyzed by colony PCR using Sphingomonas -specific primers, out of which 48 isolates had PCR-positive signals. The 48 positive amplicons generated 8 distinct restriction fragment length polymorphism (RFLP patterns, and 7 out of 8 phylotypes were identified as Sphingomonas by 16S rRNA gene sequencing of the representative strains. Within these 7 Sphingomonas strains, 6 strains were capable of using fluorene as the sole carbon source, while 2 strains were phenanthrene-degrading Sphingomonas. To the best of our knowledge, this is the first report to evaluate the relationship between PAHs contamination levels and culturable Sphingomonas in environmental samples.

Comparative metagenomics reveals impact of contaminants on groundwater microbiomes

Directory of Open Access Journals (Sweden)

Christopher L Hemme

2015-10-01

Full Text Available To understand patterns of geochemical cycling in pristine versus contaminated groundwater ecosystems, pristine shallow groundwater (FW301 and contaminated groundwater (FW106 samples from the Oak Ridge Integrated Field Research Center (OR-IFRC were sequenced and compared to each other to determine phylogenetic and metabolic difference between the communities. Proteobacteria (e.g., Burkholderia, Pseudomonas are the most abundant lineages in the pristine community, though a significant proportion (>55% of the community is composed of poorly characterized low abundance (individually <1% lineages. The phylogenetic diversity of the pristine community contributed to a broader diversity of metabolic networks than the contaminated community. In addition, the pristine community encodes redundant and mostly complete geochemical cycles distributed over multiple lineages and appears capable of a wide range of metabolic activities. In contrast, many geochemical cycles in the contaminated community appear truncated or minimized due to decreased biodiversity and dominance by Rhodanobacter populations capable of surviving the combination of stresses at the site. These results indicate that the pristine site contains more robust and encodes more functional redundancy than the stressed community, which contributes to more efficient nutrient cycling and adaptability than the stressed community.

Microbial contamination of mobile phones in a health care setting in Alexandria, Egypt.

Science.gov (United States)

Selim, Heba Sayed; Abaza, Amani Farouk

2015-01-01

This study aimed at investigating the microbial contamination of mobile phones in a hospital setting. Swab samples were collected from 40 mobile phones of patients and health care workers at the Alexandria University Students' Hospital. They were tested for their bacterial contamination at the microbiology laboratory of the High Institute of Public Health. Quantification of bacteria was performed using both surface spread and pour plate methods. Isolated bacterial agents were identified using standard microbiological methods. Methicillin-resistant Staphylococcus aureus was identified by disk diffusion method described by Bauer and Kirby. Isolated Gram-negative bacilli were tested for being extended spectrum beta lactamase producers using the double disk diffusion method according to the Clinical and Laboratory Standards Institute recommendations. All of the tested mobile phones (100%) were contaminated with either single or mixed bacterial agents. The most prevalent bacterial contaminants were methicillin-resistant S. aureus and coagulase-negative staphylococci representing 53% and 50%, respectively. The mean bacterial count was 357 CFU/ml, while the median was 13 CFU/ml using the pour plate method. The corresponding figures were 2,192 and 1,720 organisms/phone using the surface spread method. Mobile phones usage in hospital settings poses a risk of transmission of a variety of bacterial agents including multidrug-resistant pathogens as methicillin-resistant S. aureus. The surface spread method is an easy and useful tool for detection and estimation of bacterial contamination of mobile phones.

Long-term ERT monitoring of biogeochemical changes of an aged hydrocarbon contamination

Science.gov (United States)

Caterina, David; Flores Orozco, Adrian; Nguyen, Frédéric

2017-06-01

Adequate management of contaminated sites requires information with improved spatio-temporal resolution, in particular to assess bio-geochemical processes, such as the transformation and degradation of contaminants, precipitation of minerals or changes in groundwater geochemistry occurring during and after remediation procedures. Electrical Resistivity Tomography (ERT), a geophysical method sensitive to pore-fluid and pore-geometry properties, permits to gain quasi-continuous information about subsurface properties in real-time and has been consequently widely used for the characterization of hydrocarbon-impacted sediments. However, its application for the long-term monitoring of processes accompanying natural or engineered bioremediation is still difficult due to the poor understanding of the role that biogeochemical processes play in the electrical signatures. For in-situ studies, the task is further complicated by the variable signal-to-noise ratio and the variations of environmental parameters leading to resolution changes in the electrical images. In this work, we present ERT imaging results for data collected over a period of two years on a site affected by a diesel fuel contamination and undergoing bioremediation. We report low electrical resistivity anomalies in areas associated to the highest contaminant concentrations likely due transformations of the contaminant due to microbial activity and accompanying release of metabolic products. We also report large seasonal variations of the bulk electrical resistivity in the contaminated areas in correlation with temperature and groundwater level fluctuations. However, the amplitude of bulk electrical resistivity variations largely exceeds the amplitude expected given existing petrophysical models. Our results suggest that the variations in electrical properties are mainly controlled by microbial activity which in turn depends on soil temperature and hydrogeological conditions. Therefore, ERT can be suggested as

Detection, Occurrence and Fate of Emerging Contaminants in Agricultural Environments

Science.gov (United States)

Cassada, David A.; Bartelt–Hunt, Shannon L.; Li, Xu; D’Alessio, Matteo; Zhang, Yun; Zhang, Yuping; Sallach, J. Brett

2018-01-01

A total of 59 papers published in 2015 were reviewed ranging from detailed descriptions of analytical methods, to fate and occurrence studies, to ecological effects and sampling techniques for a wide variety of emerging contaminants likely to occur in agricultural environments. New methods and studies on veterinary pharmaceuticals, steroids, antibiotic resistance genes in agricultural environments continue to expand our knowledge base on the occurrence and potential impacts of these compounds. This review is divided into the following sections: Introduction, Analytical Methods, Steroid Hormones, Pharmaceutical Contaminants, Transformation Products, and “Antibiotic Resistance, Drugs, Bugs and Genes”. PMID:27620078

Characterisation of contamination migration in the workplace

International Nuclear Information System (INIS)

Boulaud, D.; Laborde, J.C.; Pourprix, M.

1994-01-01

The Institute for Nuclear Safety and Protection (IPSN) has developed a procedure for characterising airborne contamination between processes and the workplace in nuclear facilities. It was initially intended to use this process to validate operator choices concerning the monitoring of indoor air contamination (personnel monitoring, and environmental detection at fixed locations), but also to optimise the fundamental parameters which have a more or less direct influence on potential exposure of staff in the workplace (at the same time optimising the contamination source, close confinement, process ventilation and general ventilation). In practice, the methods used to obtain these expert appraisals were usually based on experiments carried out in situ: (i) characterisation of aerosol contamination by accurate measurement of the nature, concentration and particle size distribution at various locations; (ii) characterisation of the migration of contamination by precise measurement involving gas and/or particle tracing techniques. In parallel with these experiments, a considerable effort was made to develop and qualify computer codes capable of predicting or estimating the migration of contamination through complex ventilated areas, by means of both fluid mechanics and aerosol science. (Author)

Removal of emerging contaminants by simultaneous application of membrane ultrafiltration, activated carbon adsorption, and ultrasound irradiation

International Nuclear Information System (INIS)

Secondes, Mona Freda N.; Naddeo, Vincenzo; Belgiorno, Vincenzo; Ballesteros, Florencio

2014-01-01

Highlights: • Above 99% of the emerging contaminants were removed in the USAMe process. • Influence of PAC dose and US frequency on removal is studied. • Improved performance is due to PAC adsorption enhancement and sonolytic degradation. • US irradiation improved efficiency and delayed declines in the removal of contaminants. • Performance of the hybrid process is better under lower frequency ultrasound irradiation. -- Abstract: Advanced wastewater treatment is necessary to effectively remove emerging contaminants (ECs) with chronic toxicity, endocrine disrupting effects, and the capability to induce the proliferation of highly resistant microbial strains in the environment from before wastewater disposal or reuse. This paper investigates the efficiency of a novel hybrid process that applies membrane ultrafiltration, activated carbon adsorption, and ultrasound irradiation simultaneously to remove ECs. Diclofenac, carbamazepine, and amoxicillin are chosen for this investigation because of their assessed significant environmental risks. Removal mechanisms and enhancement effects are analysed in single and combined processes. The influence of adsorbent dose and ultrasonic frequency to EC removal are also investigated. Results suggest that adsorption is probably the main removal mechanism and is affected by the nature of ECs and the presence of other components in the mixture. Almost complete removals are achieved in the hybrid process for all ECs

Removal of emerging contaminants by simultaneous application of membrane ultrafiltration, activated carbon adsorption, and ultrasound irradiation

Energy Technology Data Exchange (ETDEWEB)

Secondes, Mona Freda N. [Environmental Engineering Graduate Program, Department of Chemical Engineering, University of the Philippines – Diliman, Quezon City (Philippines); Naddeo, Vincenzo, E-mail: vnaddeo@unisa.it [Sanitary and Environmental Engineering Division (SEED), Department of Civil Engineering, University of Salerno, Fisciano 84084 (Saudi Arabia) (Italy); Belgiorno, Vincenzo [Sanitary and Environmental Engineering Division (SEED), Department of Civil Engineering, University of Salerno, Fisciano 84084 (Saudi Arabia) (Italy); Ballesteros, Florencio [Environmental Engineering Graduate Program, Department of Chemical Engineering, University of the Philippines – Diliman, Quezon City (Philippines)

2014-01-15

Highlights: • Above 99% of the emerging contaminants were removed in the USAMe process. • Influence of PAC dose and US frequency on removal is studied. • Improved performance is due to PAC adsorption enhancement and sonolytic degradation. • US irradiation improved efficiency and delayed declines in the removal of contaminants. • Performance of the hybrid process is better under lower frequency ultrasound irradiation. -- Abstract: Advanced wastewater treatment is necessary to effectively remove emerging contaminants (ECs) with chronic toxicity, endocrine disrupting effects, and the capability to induce the proliferation of highly resistant microbial strains in the environment from before wastewater disposal or reuse. This paper investigates the efficiency of a novel hybrid process that applies membrane ultrafiltration, activated carbon adsorption, and ultrasound irradiation simultaneously to remove ECs. Diclofenac, carbamazepine, and amoxicillin are chosen for this investigation because of their assessed significant environmental risks. Removal mechanisms and enhancement effects are analysed in single and combined processes. The influence of adsorbent dose and ultrasonic frequency to EC removal are also investigated. Results suggest that adsorption is probably the main removal mechanism and is affected by the nature of ECs and the presence of other components in the mixture. Almost complete removals are achieved in the hybrid process for all ECs.

Thermal enhanced vapor extraction systems: Design, application and performance prediction including contaminant behavior

International Nuclear Information System (INIS)

Phelan, J.M.; Webb, S.W.

1994-01-01

Soil heating technologies have been proposed as a method to accelerate contaminant removal from subsurface soils. These methods include the use of hot air, steam, conductive heaters, in-situ resistive heating and in-situ radiofrequency heating (Buettner et.al., EPA, Dev et.al., Heath et.al.). Criteria for selection of a particular soil heating technology is a complex function of contaminant and soil properties, and efficiency in energy delivery and contaminant removal technologies. The work presented here seeks to expand the understanding of the interactions of subsurface water, contaminant, heat and vacuum extraction through model predictions and field data collection. Field demonstration will involve the combination of two soil heating technologies (resistive and dielectric) with a vacuum vapor extraction system and will occur during the summer of 1994

In situ vitrification: Demonstrated capabilities and potential applications

International Nuclear Information System (INIS)

Luey, J.K.

1993-01-01

A large-scale demonstration of the in situ vitrification (ISV) process was performed in April 1990 on the 116-B-6A Crib in the 100 Area of the Hanford Site in southeastern Washington. The 116-B-6A Crib is a radioactive mixed waste site and was selected to demonstrate the applicability of ISV to soils contaminated with mixed wastes common to many US Department of Energy (DOE) sites. Results from the demonstration show that the ISV process is a viable remediation technology for contaminated soils. The demonstration of the ISV process on an actual contaminated soil site followed research and development efforts by the Pacific Northwest Laboratory (PNL) over the last 10 years. PNL's research has led to the development of the ISV process as a viable remediation technology for contaminated soils and the creation of a commercial supplier of ISV services, Geosafe Corporation. Development efforts for ISV applications other than treatment of contaminated soils, by PNL and in collaboration with Oak Ridge National Laboratory (ORNL) and Idaho National Engineering Laboratory (INEL), show the ISV process has potential applicability for remediating buried waste sites, remediating underground storage tanks, and enabling the placement of subsurface vitrified barriers and engineered structures. This paper discusses the results from the April 1990 large-scale demonstration and provides a general overview of the current capabilities of the ISV process for contaminated soils. In addition, this paper outlines some of the technical issues associated with other ISV applications and provides a qualitative discussion of the level of effort needed to resolve these technical issues

Sensing capabilities of graphite based MR elastomers

International Nuclear Information System (INIS)

Tian, T F; Li, W H; Deng, Y M

2011-01-01

This paper presents both experimental and theoretical investigations of the sensing capabilities of graphite based magnetorheological elastomers (MREs). In this study, eight MRE samples with varying graphite weight fractions were fabricated and their resistance under different magnetic fields and external loadings were measured with a multi-meter. With an increment of graphite weight fraction, the resistance of MRE sample decreases steadily. Higher magnetic fields result in a resistance increase. Based on an ideal assumption of a perfect chain structure, a mathematical model was developed to investigate the relationship between the MRE resistance with external loading. In this model, the current flowing through the chain structure consists of both a tunnel current and a conductivity current, both of which depend on external loadings. The modelling parameters have been identified and reconstructed from comparison with experimental results. The comparison indicates that both experimental results and modelling predictions agree favourably well

Effects of dietary fructooligosaccharide levels and feeding modes on growth, immune responses, antioxidant capability and disease resistance of blunt snout bream (Megalobrama amblycephala).

Science.gov (United States)

Zhang, Chun-Nuan; Li, Xiang-Fei; Jiang, Guang-Zhen; Zhang, Ding-Dong; Tian, Hong-Yan; Li, Jun-Yi; Liu, Wen-Bin

2014-12-01

This study aimed to determine the effects of fructooligosaccharide (FOS) levels and its feeding modes on growth, immune response, antioxidant capability and disease resistance of blunt snout bream (Megalobrama amblycephala). Fish (12.5 ± 0.5 g) were subjected to three FOS levels (0, 0.4% and 0.8%) and two feeding modes (supplementing FOS continuously and supplementing FOS two days interval 5 days) according to a 3 × 2 factorial design. At the end of 8-week feeding trial, fish were challenged by Aeromonas hydrophila with concentration of 1 × 10(5) CFU mL(-1) and mortality was recorded for the next 96 h. Fish fed 0.4% FOS continuously (D2) and fish fed the basal diet for 5 days followed by 0.8% FOS for 2 days (D5) showed admirable growth performance. The highest plasma lysozyme, acid phosphatase and myeloperoxidase activities as well as complement component 3, total protein and immunoglobulin M (IgM) levels were all observed in fish fed D5. They were significantly higher (P 0.05) with that of fish fed D2. A similar trend was also observed in antioxidant capability as well as the expression of Leap-I and Leap-Ⅱ. Mortality showed an opposite trend with the immune response with the lowest rate observed in fish fed D5. The results indicated that diet supplementing FOS in appropriate levels and feeding modes could improve the growth, immune response and antioxidant capability of fish, as might consequently lead to enhanced disease resistance. It can be speculated that the basal diet for 5 days followed by 0.8% FOS for 2 days was most suitable for blunt snout bream. Copyright © 2014 Elsevier Ltd. All rights reserved.

How laser damage resistance of HfO2/SiO2 optical coatings is affected by embedded contamination caused by pausing the deposition process

Science.gov (United States)

Field, Ella; Bellum, John; Kletecka, Damon

2015-07-01

Reducing contamination is essential for producing optical coatings with high resistance to laser damage. One aspect of this principle is to make every effort to limit long interruptions during the coating's deposition. Otherwise, contamination may accumulate during the pause and become embedded in the coating after the deposition is restarted, leading to a lower laser-induced damage threshold (LIDT). However, pausing a deposition is sometimes unavoidable, despite our best efforts. For example, a sudden hardware or software glitch may require hours or even overnight to solve. In order to broaden our understanding of the role of embedded contamination on LIDT, and determine whether a coating deposited under such non-ideal circumstances could still be acceptable, this study explores how halting a deposition overnight impacts the LIDT, and whether ion cleaning can be used to mitigate any negative effects on the LIDT. The coatings investigated are a beam splitter design for high reflection at 1054 nm and high transmission at 527 nm, at 22.5° angle of incidence in S-polarization. LIDT tests were conducted in the nanosecond regime.

A Coupled model for ERT monitoring of contaminated sites

Science.gov (United States)

Wang, Yuling; Zhang, Bo; Gong, Shulan; Xu, Ya

2018-02-01

The performance of electrical resistivity tomography (ERT) system is usually investigated using a fixed resistivity distribution model in numerical simulation study. In this paper, a method to construct a time-varying resistivity model by coupling water transport, solute transport and constant current field is proposed for ERT monitoring of contaminated sites. Using the proposed method, a monitoring model is constructed for a contaminated site with a pollution region on the surface and ERT monitoring results at different time is calculated by the finite element method. The results show that ERT monitoring profiles can effectively reflect the increase of the pollution area caused by the diffusion of pollutants, but the extent of the pollution is not exactly the same as the actual situation. The model can be extended to any other case and can be used to scheme design and results analysis for ERT monitoring.

TECHNICAL EVALUATION OF ELECTRICAL RESISTIVITY METHODS AT THE DEPARTMENT OF ENERGY HANFORD SITE

International Nuclear Information System (INIS)

PETERSEN SW

2008-01-01

There is a continuing need for cost-effective subsurface characterization within the vadose zone and groundwater at the U.S. Department of Energy (DOE) Hanford Site, Richland, Washington. With more than 1600 liquid and solid waste sites and 200 burial sites, contaminants have migrated to and through the vadose zone. In addition, future groundwater plumes may be generated from contaminants presently in the vadose zone. Relatively low-cost geophysical techniques can provide spatially extensive data that may provide information about the presence and extent of some contaminants. Recent electrical resistivity surveys at Hanford have provided encouraging results for mapping of some contaminants, such as nitrate, in the vadose zone. Because mobile radionuclides and trace elements may have been transported with nitrate through the vadose zone, the method may be used to map some mobile contaminants of concern, such as technetium-99 (99Tc). Validation of these recent electrical resistivity survey results remains to be completed. Electrical resistivity surveys have been conducted at various waste sites in the 200 Area of the Hanford Site: BC Cribs and Trenches (BCCT), T, S, U, C, B Tank Farms and the Purex Plant. Surveys have been completed using surface and well-to-well (WTW) array configurations. The goals of the surveys, as described by Fluor Hanford and CH2MHill Hanford staff, were to test the applicability of resistivity methods in identifying the presence of and mapping approximate extent of contaminant plumes within the vadose zone. The overall goal of the project was to evaluate the utility of electrical resistivity methods for characterizing contaminants of potential concern in the vadose zone in the 200 Area of the Hanford Site. The panel was asked to perform the following activities: (1) Evaluate recently completed and ongoing electrical resistivity projects at Hanford in terms of methodology used, results obtained, and lessons learned, with specific focus on (a

The resistance of Bacillus atrophaeus spores to the bactericidal activity of peracetic acid is influenced by both the nature of the solid substrates and the mode of contamination.

Science.gov (United States)

Grand, I; Bellon-Fontaine, M-N; Herry, J-M; Hilaire, D; Moriconi, F-X; Naïtali, M

2010-11-01

To evaluate the impact of the mode of contamination in relation with the nature of solid substrates on the resistance of spores of Bacillus atrophaeus -selected as surrogates of Bacillus anthracis- to a disinfectant, peracetic acid. Six materials confronted in urban and military environments were selected for their different structural and physicochemical properties. In parallel, two modes of contamination were examined, i.e. deposition and immersion. Deposition was used to simulate contamination by an aerosol and immersion by an extended contact with liquids. A pronounced difference in the biocontamination levels and spatial organization of spores was observed depending on the mode of contamination and the nature of the solid substrate considered, with consequences on decontamination. Contamination by immersion led to lower efficiency of peracetic acid decontamination than contamination by deposition. Infiltration of spores into porous materials after immersion is one reason. In contrast, the deposition mode aggregates cells at the surface of materials, explaining the similar disinfecting behaviour of porous and nonporous substrates when considering this inoculation route. The inoculation route was shown to be as influential a parameter as material characteristics (porosity and wettability) for decontamination efficacy. These results provide comparative information for the decontamination of B. atrophaeus spores in function of the mode of contamination and the nature of solid substrates. Journal of Applied Microbiology © 2010 The Society for Applied Microbiology. No claim to French government works.

Automatic Measurement of Low Level Contamination on Concrete Surfaces

International Nuclear Information System (INIS)

Tachibana, M.; Itoh, H.; Shimada, T.; Yanagihara, S.

2002-01-01

Automatic measurement of radioactivity is necessary for considering cost effectiveness in final radiological survey of building structures in decommissioning nuclear facilities. The RAPID (radiation measuring pilot device for surface contamination) was developed to be applied to automatic measurement of low level contamination on concrete surfaces. The RAPID has a capability to measure contamination with detection limit of 0.14 Bq/cm2 for 60Co in 30 seconds of measurement time and its efficiency is evaluated to be 5 m2/h in a normal measurement option. It was confirmed that low level contamination on concrete surfaces could be surveyed by the RAPID efficiently compared with direct measurement by workers through its actual application

Analytical model of contamination during the drying of cylinders of jamonable muscle

Science.gov (United States)

Montoya Arroyave, Isabel

2014-05-01

For a cylinder of jamonable muscle of radius R and length much greater than R; considering that the internal resistance to the transfer of water is much greater than the external and that the internal resistance is one certain function of the distance to the axis; the distribution of the punctual moisture in the jamonable cylinder is analytically computed in terms of the Bessel's functions. During the process of drying and salted the jamonable cylinder is sensitive to contaminate with bacterium and protozoa that come from the environment. An analytical model of contamination is presents using the diffusion equation with sources and sinks, which is solve by the method of the Laplace transform, the Bromwich integral, the residue theorem and some special functions like Bessel and Heun. The critical times intervals of drying and salted are computed in order to obtain the minimum possible contamination. It is assumed that both external moisture and contaminants decrease exponentially with time. Contaminants profiles are plotted and discussed some possible techniques of contaminants detection. All computations are executed using Computer Algebra, specifically Maple. It is said that the results are important for the food industry and it is suggested some future research lines.

Antimicrobial Resistance in the Food Chain: A Review

Science.gov (United States)

Verraes, Claire; Van Boxstael, Sigrid; Van Meervenne, Eva; Van Coillie, Els; Butaye, Patrick; Catry, Boudewijn; de Schaetzen, Marie-Athénaïs; Van Huffel, Xavier; Imberechts, Hein; Dierick, Katelijne; Daube, George; Saegerman, Claude; De Block, Jan; Dewulf, Jeroen; Herman, Lieve

2013-01-01

Antimicrobial resistant zoonotic pathogens present on food constitute a direct risk to public health. Antimicrobial resistance genes in commensal or pathogenic strains form an indirect risk to public health, as they increase the gene pool from which pathogenic bacteria can pick up resistance traits. Food can be contaminated with antimicrobial resistant bacteria and/or antimicrobial resistance genes in several ways. A first way is the presence of antibiotic resistant bacteria on food selected by the use of antibiotics during agricultural production. A second route is the possible presence of resistance genes in bacteria that are intentionally added during the processing of food (starter cultures, probiotics, bioconserving microorganisms and bacteriophages). A last way is through cross-contamination with antimicrobial resistant bacteria during food processing. Raw food products can be consumed without having undergone prior processing or preservation and therefore hold a substantial risk for transfer of antimicrobial resistance to humans, as the eventually present resistant bacteria are not killed. As a consequence, transfer of antimicrobial resistance genes between bacteria after ingestion by humans may occur. Under minimal processing or preservation treatment conditions, sublethally damaged or stressed cells can be maintained in the food, inducing antimicrobial resistance build-up and enhancing the risk of resistance transfer. Food processes that kill bacteria in food products, decrease the risk of transmission of antimicrobial resistance. PMID:23812024

Contamination measurements on persons after a nuclear accident

International Nuclear Information System (INIS)

Maushart, R.

1992-01-01

The purpose of contamination measurements after accidents is threefold: to detect and localize contaminations; to determine the level of contamination as a base for medical decisions; and to check the scope and efficiency of the decontamination measures. Persons involved in accidents should never measure their contamination themselves. The radiation protection personnel, whether it belongs to the medical team or to the disaster control squads, must be familiar with the measuring instruments and experienced in handling these instruments. A high priority has to be placed on training and constant practice. The monitors used must meet the special requirements of an emergency situation. This includes resistance against environmental factors - temperature, humidity, vibrations - as well as the simplicity of handling the instrument, and the clear presentation of the results. (author)

INFECUNDITY AND CONSUMPTION OF PCB-CONTAMINATED SPORT FISH

Science.gov (United States)

Biologic capacity for reproduction, or fecundity, may be threatened by environmental contaminants, especially compounds capable of disrupting endocrine pathways. Telephone interviews that focused on reproductive events were conducted with female members of the New York State Angl...

Structural reliability assessment capability in NESSUS

Science.gov (United States)

Millwater, H.; Wu, Y.-T.

1992-07-01

The principal capabilities of NESSUS (Numerical Evaluation of Stochastic Structures Under Stress), an advanced computer code developed for probabilistic structural response analysis, are reviewed, and its structural reliability assessed. The code combines flexible structural modeling tools with advanced probabilistic algorithms in order to compute probabilistic structural response and resistance, component reliability and risk, and system reliability and risk. An illustrative numerical example is presented.

Characterizing leachate contamination in a landfill site using Time Domain Electromagnetic (TDEM) imaging

Science.gov (United States)

Baawain, Mahad S.; Al-Futaisi, Ahmed M.; Ebrahimi, A.; Omidvarborna, Hamid

2018-04-01

Time Domain Electromagnetic (TDEM) survey as well as drilling investigations were conducted to identify possible contamination of a dumping site in an unsaturated zone located in Barka, Oman. The method was applied to evaluate conductivity of the contaminated plumes in hot and arid/semiarid region, where high temperatures commonly ranged between 35 and 50 °C. The drilling investigation was carried out over the survey area to verify the geophysical results. The low-resistivity zone (90 Ωm) was correlated with compacted or cemented gravels and cobbles, particularly that of medium dense to very dense gravels and cobbles. Additionally, the TDEM profiles suggested that the plume migration followed a preferential flow path. The resistivity range 40-80 Ωm considered as contaminated areas; however, the drilling results showed the close resistivity domain in the depth >70 m below water table for some profiles (BL1, BL2, BL3, BL4 and BL5). The combined results of drilling wells, piezometers, and TDEM apparent resistivity maps showed a coincidence of the migrated leachate plume and water table. Predicted zone of the probable contamination was located at the depth of around 65 m and horizontal offset ranges 0-280 m, 80-240 m, and 40-85 m in the sounding traverses of BL4, BL6 and BL7, respectively.

Detection capabilities. Some historical footnotes

International Nuclear Information System (INIS)

Currie, L.A.

2017-01-01

Part I Summary of relevant topics from 1923 to present-including: Currie (Anal Chem 40:586-593, 1968) detection concepts and capabilities; International detection and uncertainty standards; Failure of classical "1"4C dating and birth of new scientific disciplines; Exploratory nuclear data analysis of "8"5Kr monitors found coincident with the collapse of the Iron Curtain (1989); Faulty statistics proved responsible for mistaken assertions that Currie's LC yields excessive false positives; Low-level counting and AMS for atmospheric "3"7Ar and µmolar fossil/biomass carbon in the environment; Erroneous assumption that our low-level background is a Poisson Process, linked to ∼8 % spurious anticoincidence events. Part II. Exact treatment of bivariate Poisson data-solved in 1930s by Przyborowski and Wilenski, Krakow University, for detecting extreme trace amounts of a malicious contaminant (dodder) in high purity seed standards. We adapted their treatment to detection capabilities in ultra-low-level nuclear counting. The timing of their work had great historical significance, marking the start of World War II, with the invasion of Poland (1939). (author)

Geoelectrical characterization of a site with hydrocarbon contamination caused by pipeline leakage

Energy Technology Data Exchange (ETDEWEB)

Delgado-Rodriguez, Omar; Shevnin, Vladimir; Ochoa-Valdes, Jesus [Instituto Mexicano del Petroleo, Mexico, D.F. (Mexico); Ryjov, Albert [Moscow State Geological Prospecting Academy, Moscow (Russian Federation)

2006-01-15

Vertical Electrical Sounding (VES) method is used extensively in environmental impact studies including hydrocarbon contamination. In this work, the results of the geoelectrical characterization of a contaminated site caused by pipeline leakage are presented. Geoelectrical study was performed with multi-electrode technology and 2D profile data interpretation. VES results from six parallel profiles were presented in resistivity sections and maps. Layered model of the site was found including aquifer and aquitard layers. Although the contamination grade of the site is low, we found two contaminated zones into sandy aquifer. Aquifer and aquitard were characterized by its resistivity, clay content, porosity and cation exchange capacity values. Recalculation of resistivity data into petrophysical sections and maps was performed by an inversion algorithm taking into account pore water salinity. Petrophysical parameters for uncontaminated areas estimated from resistivity are close to real values; meanwhile, in contaminated zones petrophysical parameters have anomalous values. Similar effects of contamination influence on petrophysical parameters were found in laboratory by resistivity measurements made at clean and contaminated sand samplers. [Spanish] El metodo Sondeo Electrico Vertical (SEV) es ampliamente utilizado en estudios de impacto ambiental incluyendo el caso de contaminacion por hidrocarburos. En este trabajo se presentan los resultados de la caracterizacion geoelectrica de un sitio contaminado por hidrocarburos relacionado con una fuga en linea de ducto. El estudio geoelectrico fue realizado utilizando el metodo SEV en la variante de tomografia, realizandose una interpretacion 2D de los datos observados. Seis perfiles paralelos de SEV fueron medidos y presentados sus resultados en secciones y mapas. Se determino un modelo estratificado que incluye acuitardo y acuifero. Aunque el grado de contaminacion en este sitio es bajo fue posible localizar dos zonas

Is the IP response related to geology or contaminants in a leachate plume at the Grindsted Landfill, Denmark?

DEFF Research Database (Denmark)

Møller, Ingelise; Maurya, Pradip Kumar; Balbarini, Nicola

Contaminants in leachate plumes from landfills and other contaminated sites are a threat to the environment. Efficient site characterization methods are needed. The perspectives of the IP method are investigated in combination with geological sampling and chemical analyses of water samples. Along...... a leachate plume from a landfill hosting both household and chemical waste, borehole IP data, geological samples, grain size, and contaminant concentrations in water samples are examined for correlations related to geology and concentrations of contaminants. Results relating the Cole-Cole parameters...... with sediment types and pore water resistivity representing the concentrations of the contaminants show that the formation resistivity primarily is controlled by the contaminant concentrations while the IP parameters primarily are related to the clay content and grain size distribution of sandy sediments...

Is the IP response related to geology or contaminants in a leachate plume at the Grindsted Landfill, Denmark?

DEFF Research Database (Denmark)

Møller, Ingelise; Maurya, Pradip Kumar; Balbarini, Nicola

a leachate plume from a landfill hosting both household and chemical waste, borehole IP data, geological samples, grain size, and contaminant concentrations in water samples are examined for correlations related to geology and concentrations of contaminants. Results relating the Cole-Cole parameters...... with sediment types and pore water resistivity representing the concentrations of the contaminants show that the formation resistivity primarily is controlled by the contaminant concentrations while the IP parameters primarily are related to the clay content and grain size distribution of sandy sediments......Contaminants in leachate plumes from landfills and other contaminated sites are a threat to the environment. Efficient site characterization methods are needed. The perspectives of the IP method are investigated in combination with geological sampling and chemical analyses of water samples. Along...

Antimicrobial resistance in the environment

National Research Council Canada - National Science Library

Keen, Patricia L; Montforts, M. H. M. M

2012-01-01

... or antibiotic resistance genes as environmental contaminants. It also considers alternate uses and functions for antimicrobial compounds other than those intended for medicinal purposes in humans, animals, and fish...

A combined PHREEQC-2/parallel fracture model for the simulation of laminar/non-laminar flow and contaminant transport with reactions

Science.gov (United States)

Masciopinto, Costantino; Volpe, Angela; Palmiotta, Domenico; Cherubini, Claudia

2010-09-01

A combination of a parallel fracture model with the PHREEQC-2 geochemical model was developed to simulate sequential flow and chemical transport with reactions in fractured media where both laminar and turbulent flows occur. The integration of non-laminar flow resistances in one model produced relevant effects on water flow velocities, thus improving model prediction capabilities on contaminant transport. The proposed conceptual model consists of 3D rock-blocks, separated by horizontal bedding plane fractures with variable apertures. Particle tracking solved the transport equations for conservative compounds and provided input for PHREEQC-2. For each cluster of contaminant pathways, PHREEQC-2 determined the concentration for mass-transfer, sorption/desorption, ion exchange, mineral dissolution/precipitation and biodegradation, under kinetically controlled reactive processes of equilibrated chemical species. Field tests have been performed for the code verification. As an example, the combined model has been applied to a contaminated fractured aquifer of southern Italy in order to simulate the phenol transport. The code correctly fitted the field available data and also predicted a possible rapid depletion of phenols as a result of an increased biodegradation rate induced by a simulated artificial injection of nitrates, upgradient to the sources.

Monitoring the degradation capability of novel haloalkaliphilic tributyltin chloride (TBTCl) resistant bacteria from butyltin-polluted site.

Science.gov (United States)

Hassan, Hamdy A; Dawah, Somya E; El-Sheekh, Mostafa M

2018-03-28

Tributyltin (TBT) is recognized as a major environmental problem at a global scale. Haloalkaliphilic tributyltin (TBT)-degrading bacteria may be a key factor in the remediation of TBT polluted sites. In this work, three haloalkaliphilic bacteria strains were isolated from a TBT-contaminated site in the Mediterranean Sea. After analysis of the 16S rRNA gene sequences the isolates were identified as Sphingobium sp. HS1, Stenotrophomonas chelatiphaga HS2 and Rhizobium borbori HS5. The optimal growth conditions for biodegradation of TBT by the three strains were pH 9 and 7% (w/v) salt concentration. S. chelatiphaga HS2 was the most effective TBT degrader and has the ability to transform most TBT into dibutyltin and monobutyltin (DBT and MBT). A gene was amplified from strain HS2 and identified as TBTB-permease-like, that encodes an ArsB-permease. A reverse transcription polymerase chain reaction analysis in the HS2 strain confirmed that the TBTB-permease-like gene contributes to TBT resistance. The three novel haloalkaliphilic TBT degraders have never been reported previously. Copyright © 2018 Asociación Argentina de Microbiología. Publicado por Elsevier España, S.L.U. All rights reserved.

Tributyltin-resistant bacteria from estuarine and freshwater sediments.

Science.gov (United States)

Wuertz, S; Miller, C E; Pfister, R M; Cooney, J J

1991-01-01

Resistance to tributyltin (TBT) was examined in populations from TBT-polluted sediments and nonpolluted sediments from an estuary and from fresh water as well as in pure cultures isolated from those sediments. The 50% effective concentrations (EC50s) for populations were higher at a TBT-polluted freshwater site than at a site without TBT, suggesting that TBT selected for a TBT-resistant population. In contrast, EC50s were significantly lower for populations from a TBT-contaminated estuarine site than for those from a site without TBT, suggesting that other factors in addition to TBT determine whether populations become resistant. EC50s for populations from TBT-contaminated freshwater sediments were nearly 30 times higher than those for populations from TBT-contaminated estuarine sediments. We defined a TBT-resistant bacterium as one which grows on trypticase soy agar containing 8.4 microM TBT, a concentration which prevented the growth of 90% of the culturable bacteria from these sediments. The toxicity of TBT in laboratory media was influenced markedly by the composition of the medium and whether it was liquid or solid. Ten TBT-resistant isolates from estuarine sediments and 19 from freshwater sediments were identified to the genus level. Two isolates, each a Bacillus sp., may be the first gram-positive bacteria isolated from fresh water in the presence of a high concentration of TBT. There was a high incidence of resistance to heavy metals: metal resistance indices were 0.76 for estuarine isolates and 0.68 for freshwater isolates.(ABSTRACT TRUNCATED AT 250 WORDS) PMID:1746939

Characterization of the extremely arsenic-resistant Brevibacterium linens strain AE038-8 isolated from contaminated groundwater in Tucumán, Argentina

Science.gov (United States)

Maizel, Daniela; Blum, Jodi S.; Ferrero, Marcela A.; Utturkar, Sagar M.; Brown, Steven D.; Rosen, Barry P.; Oremland, Ronald S.

2015-01-01

Brevibacterium linens AE038-8, isolated from As-contaminated groundwater in Tucumán (Argentina), is highly resistant to arsenic oxyanions, being able to tolerate up to 1 M As(V) and 75 mM As(III) in a complex medium. Strain AE038-8 was also able to reduce As(V) to As(III) when grown in complex medium but paradoxically it could not do this in a defined minimal medium with sodium acetate and ammonium sulfate as carbon and nitrogen sources, respectively. No oxidation of As(III) to As(V) was observed under any conditions. Three copies of the ars operon comprising arsenic resistance genes were found on B. linens AE038-8 genome. In addition to the well known arsC, ACR3 andarsR, two copies of the arsO gene of unknown function were detected.

COUPLED FREE AND DISSOLVED PHASE TRANSPORT: NEW SIMULATION CAPABILITIES AND PARAMETER INVERSION

Science.gov (United States)

The vadose zone free-phase simulation capabilities of the US EPA Hydrocarbon Spill Screening Model (HSSM) (Weaver et al., 1994) have been linked with the 3-D multi-species dissolved-phase contaminant transport simulator MT3DMS (Zheng and Wang, 1999; Zheng, 2005). The linkage pro...

Long-term ERT monitoring of biogeochemical changes of an aged hydrocarbon contamination.

Science.gov (United States)

Caterina, David; Flores Orozco, Adrian; Nguyen, Frédéric

2017-06-01

Adequate management of contaminated sites requires information with improved spatio-temporal resolution, in particular to assess bio-geochemical processes, such as the transformation and degradation of contaminants, precipitation of minerals or changes in groundwater geochemistry occurring during and after remediation procedures. Electrical Resistivity Tomography (ERT), a geophysical method sensitive to pore-fluid and pore-geometry properties, permits to gain quasi-continuous information about subsurface properties in real-time and has been consequently widely used for the characterization of hydrocarbon-impacted sediments. However, its application for the long-term monitoring of processes accompanying natural or engineered bioremediation is still difficult due to the poor understanding of the role that biogeochemical processes play in the electrical signatures. For in-situ studies, the task is further complicated by the variable signal-to-noise ratio and the variations of environmental parameters leading to resolution changes in the electrical images. In this work, we present ERT imaging results for data collected over a period of two years on a site affected by a diesel fuel contamination and undergoing bioremediation. We report low electrical resistivity anomalies in areas associated to the highest contaminant concentrations likely due transformations of the contaminant due to microbial activity and accompanying release of metabolic products. We also report large seasonal variations of the bulk electrical resistivity in the contaminated areas in correlation with temperature and groundwater level fluctuations. However, the amplitude of bulk electrical resistivity variations largely exceeds the amplitude expected given existing petrophysical models. Our results suggest that the variations in electrical properties are mainly controlled by microbial activity which in turn depends on soil temperature and hydrogeological conditions. Therefore, ERT can be suggested as

Response of microbial activities and diversity to PAHs contamination at coal tar contaminated land

Science.gov (United States)

Zhao, Xiaohui; Sun, Yujiao; Ding, Aizhong; Zhang, Dan; Zhang, Dayi

2015-04-01

Coal tar is one of the most hazardous and concerned organic pollutants and the main hazards are polycyclic aromatic hydrocarbons (PAHs). The indigenous microorganisms in soils are capable to degrade PAHs, with essential roles in biochemical process for PAHs natural attenuation. This study investigated 48 soil samples (from 8 depths of 6 boreholes) in Beijing coking and chemistry plant (China) and revealed the correlation between PAHs contamination, soil enzyme activities and microbial community structure, by 16S rRNA denaturing gradient gel electrophoresis (DGGE). At the site, the key contaminants were identified as naphthalene, acenaphthylene, acenaphthene, fluorene, phenanthrene and anthracene, and the total PAHs concentration ranged from 0.1 to 923.9 mg/kg dry soil. The total PAHs contamination level was positively correlated (pcatalase activities (0.554-6.230 mL 0.02 M KMnO4/g•h) and dehydrogenase activities (1.9-30.4 TF μg/g•h soil), showing the significant response of microbial population and degrading functions to the organic contamination in soils. The PAHs contamination stimulated the PAHs degrading microbes and promoted their biochemical roles in situ. The positive relationship between bacteria count and dehydrogenase activities (p<0.05) suggested the dominancy of PAHs degrading bacteria in the microbial community. More interestingly, the microbial community deterioration was uncovered via the decline of microbial biodiversity (richness from 16S rRNA DGGE) against total PAHs concentration (p<0.05). Our research described the spatial profiles of PAHs contamination and soil microbial functions at the PAHs heavily contaminated sites, offering deeper understanding on the roles of indigenous microbial community in natural attenuation process.

Effect of soil biochar amendment on grain crop resistance to Fusarium mycotoxin contamination

Science.gov (United States)

Mycotoxin contamination of food and feed is among the top food safety concerns. Fusarium spp. cause serious diseases in cereal crops reducing yield and contaminating grain with mycotoxins that can be deleterious to human and animal health. Fusarium graminearum and Fusarium verticillioides infect whe...

The value of DCIP geophysical surveys for contaminated site investigations

DEFF Research Database (Denmark)

Balbarini, Nicola; Rønde, Vinni Kampman; Maurya, Pradip Kumar

an old factory site by combining traditional geological, hydrological, and contaminant concentration data with DCIP surveys. The plume consisted of xenobiotic organic compounds and inorganics. The study assesses benefits and limitations of DCIP geophysics for contaminated site investigations. A 3D......Geophysical methods are increasingly being used in contaminant hydrogeology to map lithology, hydraulic properties, and contaminant plumes with a high ionic strength. Advances in the Direct Current resistivity and Induced Polarization (DCIP) method allow the collection of high resolution three...... water and below the streambed. Surface DCIP surveys supported the characterization of the spatial variability in geology, hydraulic conductivity and contaminant concentration. Though DCIP data interpretation required additional borehole data, the DCIP survey reduced the number of boreholes required...

Antibiotic-Resistant Enteric Bacteria in Environmental Waters

OpenAIRE

Lisa M. Casanova; Mark D. Sobsey

2016-01-01

Sources of antibiotic resistant organisms, including concentrated animal feeding operations (CAFOs), may lead to environmental surface and groundwater contamination with resistant enteric bacteria of public health concern. The objective of this research is to determine whether Salmonella, Escherichia coli, Yersinia enterocolitica, and enterococci resistant to clinically relevant antibiotics are present in surface and groundwater sources in two eastern North Carolina counties, Craven and Wayne...

Microbial characterization of a radionuclide- and metal-contaminated waste site

International Nuclear Information System (INIS)

Bolton, H. Jr.; Lumppio, H.L.; Ainsworth, C.C.; Plymale, A.E.

1993-04-01

The operation of nuclear processing facilities and defense-related nuclear activities has resulted in contamination of near-surface and deep-subsurface sediments with both radionuclides and metals. The presence of mixed inorganic contaminants may result in undetectable microbial populations or microbial populations that are different from those present in uncontaminated sediments. To determine the impact of mixed radionuclide and metal contaminants on sediment microbial communities, we sampled a processing pond that was used from 1948 to 1975 for the disposal of radioactive and metal-contaminated wastewaters from laboratories and nuclear fuel fabrication facilities on the Hanford Site in Washington State. Because the Hanford Site is located in a semiarid environment with average rainfall of 159 mm/year, the pond dried and a settling basin remained after wastewater input into the pond ceased in 1975. This processing pond basin offered a unique opportunity to obtain near-surface sediments that had been contaminated with both radionuclides and metals for several decades. Our objectives were to determine the viable populations of microorganisms in the sediments and to test several hypotheses about how the addition of both radionuclides and metals influenced the microbial ecology of the sediments. Our first hypothesis was that viable populations of microorganisms would be lower in the more contaminated sediments. Second, we expected that long-term metal exposure would result in enhanced metal resistance. Finally, we hypothesized that microorganisms from the most radioactive sediments should have had enhanced radiation resistance

Upgrading Regional Capability to Assess Marine Contaminants in the ARASIA member States

International Nuclear Information System (INIS)

ELSamad, O.

2010-01-01

This project enhances the national capabilities to monitor and assess marine radioactivity as part of a national monitoring program. This will be very beneficial as, the monitoring processes and control of marine pollution is a very strategic important objective of the governments, while many national decrees recently issued includes environmental protection and rehabilitation of the marine environment. (author)

Carbon contaminant in the ion processing of aluminum oxide film

International Nuclear Information System (INIS)

Chaug, Y.; Roy, N.

1989-01-01

Ion processing can induce contamination on the bombarded surface. However, this process is essential for the microelectronics device fabrication. Auger electron spectroscopy has been used to study the simultaneous deposition of carbon impurity during ion bombardment of magnetron rf-sputtering deposited aluminum oxide film. Ion bombardment on aluminum oxide results in a preferential removal of surface oxygen and a formation of a metastable state of aluminum suboxide. Cosputtered implanted carbon contaminant appears to have formed a new state of stoichiometry on the surface of the ion bombarded aluminum oxide and existed as an aluminum carbide. This phase has formed due to the interaction of the implanted carbon and the aluminum suboxide. The Ar + ion sputter etching rate is reduced for the carbon contaminated oxide. The electrical resistance of the aluminum oxide between two gold strips has been measured. It is found that the electrical resistance is also reduced due to the formation of the new stoichiometry on the surface

Global risk of pharmaceutical contamination from highly populated developing countries.

Science.gov (United States)

Rehman, Muhammad Saif Ur; Rashid, Naim; Ashfaq, Muhammad; Saif, Ameena; Ahmad, Nasir; Han, Jong-In

2015-11-01

Global pharmaceutical industry has relocated from the west to Asian countries to ensure competitive advantage. This industrial relocation has posed serious threats to the environment. The present study was carried out to assess the possible pharmaceutical contamination in the environment of emerging pharmaceutical manufacturing countries (Bangladesh, China, India and Pakistan). Although these countries have made tremendous progress in the pharmaceutical sector but most of their industrial units discharge wastewater into domestic sewage network without any treatment. The application of untreated wastewater (industrial and domestic) and biosolids (sewage sludge and manure) in agriculture causes the contamination of surface water, soil, groundwater, and the entire food web with pharmaceutical compounds (PCs), their metabolites and transformed products (TPs), and multidrug resistant microbes. This pharmaceutical contamination in Asian countries poses global risks via product export and international traveling. Several prospective research hypotheses including the development of new analytical methods to monitor these PCs/TPs and their metabolites, highly resistant microbial strains, and mixture toxicity as a consequence of pharmaceutical contamination in these emerging pharmaceutical exporters have also been proposed based on the available literature. Copyright © 2013 Elsevier Ltd. All rights reserved.

Association of Environmental Contamination in the Home With the Risk for Recurrent Community-Associated, Methicillin-Resistant Staphylococcus aureus Infection.

Science.gov (United States)

Knox, Justin; Sullivan, Sean B; Urena, Julia; Miller, Maureen; Vavagiakis, Peter; Shi, Qiuhu; Uhlemann, Anne-Catrin; Lowy, Franklin D

2016-06-01

The role of environmental contamination in recurrent Staphylococcus aureus infections within households and its potential effect on intervention strategies has been debated recently. To assess whether household environmental contamination increases the risk for recurrent infection among individuals with a community-associated methicillin-resistant S aureus (MRSA) infection. This cohort study was conducted from November 1, 2011, to June 30, 2014, in the Columbia University Medical Center catchment area. All patients within 72 hours of presentation with skin or soft-tissue infections and blood, urine, or sputum cultures positive for MRSA were identified. Two hundred sixty-two patients met study inclusion criteria; 83 of these (31.7%) agreed to participate (index patients) with 214 household members. Participants were followed up for 6 months, and 62 of the 83 households (74.7%) completed follow-up. Participants and researchers were blinded to exposure status throughout the study. Follow-up was completed on June 30, 2014, and data were assessed from July 1, 2014, to February 19, 2016. Concordant environmental contamination, defined as having an isolate with the identical staphylococcal protein A and staphylococcal chromosomal cassette mec type or antibiogram type as the index patient's clinical isolate, present on 1 or more environmental surfaces at the time of a home visit to the index patient after infection. Index recurrent infection, defined as any self-reported infection among the index patients during follow-up. One patient did not complete any follow-up. Of the remaining 82 index patients, 53 (64.6%) were female and 59 (72.0%) were Hispanic. The mean age was 30 (SD, 20; range, 1-79) years. Forty-nine of 61 MRSA infections where the clinical isolate could be obtained (80.3%) were due to the epidemic strain USA300. Among the 82 households in which a patient had an index MRSA infection, the clinical isolate was present in the environment in 20 (24.4%) and not

Pressure vessel code construction capabilities for a nickel-chromium-tungsten-molybdenum alloy

International Nuclear Information System (INIS)

Rothman, M.F.

1990-01-01

HAYNES alloy 230 (UNS NO6230) has achieved wide usage in a variety of high-temperature aerospace, chemical process industry and industrial heating applications since its introduction in 1981. Combining high elevated temperature strength with excellent metallurgical stability, environment-resistance and relatively straight forward fabrication characteristics, this Ni-Cr-W-Mo alloy was an excellent candidate for ASME Pressure vessel Code applications. Coverage under case No. 2063 was granted in July, 1989, for both Section I and Section VIII Division 1 construction. In this paper, the metallurgy of 230 alloy will be described, and its design strength capabilities contrasted with those for more established code materials. Other important performance capabilities, such as long-term thermal stability, oxidation-resistance, fatigue-resistance, and resistance to other forms of environmental degradation will be discussed. It will be shown that the combined properties of 230 alloy offer some significant advantages over other materials for applications such as expansion bellows, heat-exchangers, valves and other components in the fossil energy, nuclear energy and chemical process industries, among others

Creosote-contaminated sites: their potential for bioremediation

Energy Technology Data Exchange (ETDEWEB)

Mueller, J G; Chapman, P J; Pritchard, P H [US EPA Environmental Research Laboratory, Gulf Breeze, FL (USA)

1989-10-01

Coal tar creosote contamination is generally associated with surface soils, waters in treatment lagoons or evaporation areas, and groundwater contaminated with leachate from the above sources. The basic principle of bioremediation is to exploit the ability of microorganisms to catabolize a wide range of organic substrates. There are limitations which much be addressed if in situ bioremediation is to be successful: the pollutant must be in a chemical state conducive to microbial utilization, aeration and nutrient supplementation are essential elements of many in situ treatments, and there must be present an acclimated microbial population capable of degrading the pollutant. 35 refs., 3 tabs.

Nuclear, biological and chemical contamination survivability of Army material

International Nuclear Information System (INIS)

Feeney, J.J.

1987-01-01

Army Regulation (AR) 70-71, Nuclear, Biological and Chemical (NBC) Contamination Survivability of Army Material, published during 1984, establishes Army policy and procedures for the development and acquisition of material to ensure its survivablility and sustainability on the NBC-contaminated battlefield. This regulation defines NBC contamination as a term that includes both the individual and collective effects of residual radiological, biological, and chemical contamination. AR 70-71 applies to all mission-essential equipment within the Army. NBC contamination survivability is the capability of a system and its crew to withstand an NBC-contaminated environment, including decontamination, without losing the ability to accomplish the assigned mission. Characteristics of NBC contamination survivability are decontaminability, hardness, and compatability. These characteristics are engineering design criteria which are intended for use only in a developmental setting. To comply with AR 70-71, each mission-essential item must address all three criteria. The Department of Defense (DOD) has published a draft instruction addressing acquisition of NBC contamination survivable systems. This instruction will apply throughout DOD to those programs, systems and subsystems designated by the Secretary of Defense as major systems acquisition programs and to those non-major systems that have potential impact on critical functions

Combined effects of dietary fructooligosaccharide and Bacillus licheniformis on innate immunity, antioxidant capability and disease resistance of triangular bream (Megalobrama terminalis).

Science.gov (United States)

Zhang, Chun-Nuan; Li, Xiang-Fei; Xu, Wei-Na; Jiang, Guang-Zhen; Lu, Kang-Le; Wang, Li-Na; Liu, Wen-Bin

2013-11-01

This study was conducted to investigate the effects of fructooligosaccharide (FOS) and Bacillus licheniformis (B. licheniformis) and their interaction on innate immunity, antioxidant capability and disease resistance of triangular bream Megalobrama terminalis (average initial weight 30.5 ± 0.5 g). Nine experimental diets were formulated to contain three FOS levels (0, 0.3% and 0.6%) and three B. licheniformis levels (0, 1 × 10(7), 5 × 10(7) CFU g(-1)) according to a 3 × 3 factorial design. At the end of the 8-week feeding trial, fish were challenged by Aeromonas hydrophila (A. hydrophila) and survival rate was recorded for the next 7 days. The results showed that leucocyte counts, alternative complement activity as well as total serum protein and globulin contents all increased significantly (P licheniformis levels increased from 0 to 1 × 10(7) CFU g(-1), while little difference (P > 0.05) was observed in these parameters in terms of dietary FOS levels. Both plasma alkaline phosphatase and phenoloxidase activities were significantly (P 0.05) by both FOS and B. licheniformis. Liver catalase, glutathione peroxidase as well as plasma SOD activities of fish fed 1 × 10(7) CFU g(-1)B. licheniformis were all significantly (P 0.05) by either FOS levels or B. licheniformis contents, whereas a significant (P licheniformis. The results of this study indicated that dietary FOS and B. licheniformis could significantly enhance the innate immunity and antioxidant capability of triangular bream, as well as improve its disease resistance. The best combination of these two prebiotics and/or probiotics was 0.3% FOS and 1 × 10(7) CFU g(-1)B. licheniformis. Copyright © 2013 Elsevier Ltd. All rights reserved.

Antimicrobial resistance in aerobic bacteria isolated from oral ...

African Journals Online (AJOL)

... varied antimicrobial susceptibility patterns. The oral cavities of hunting dogs are laden with multi-drug resistant bacteria of significant public health importance that could be transferred to humans through contaminated hunted games and bite wound. Keywords: Aerobic bacteria, Antimicrobial resistance, Dogs, Oral cavity, ...

Using biotechnology to enhance host resistance to aflatoxin ...

African Journals Online (AJOL)

Host resistance is the most widely explored strategy for eliminating aflatoxin contamination by Aspergillus flavus. Breeding strategies for developing resistant corn germplasm have been enhanced by the development of new screening tools for field inoculation and for laboratory screening. RFLP analysis of corn populations ...

Carbapenem-Resistant Acinetobacter baumannii: Concomitant Contamination of Air and Environmental Surfaces.

Science.gov (United States)

Shimose, Luis A; Masuda, Eriko; Sfeir, Maroun; Berbel Caban, Ana; Bueno, Maria X; dePascale, Dennise; Spychala, Caressa N; Cleary, Timothy; Namias, Nicholas; Kett, Daniel H; Doi, Yohei; Munoz-Price, L Silvia

2016-07-01

OBJECTIVE To concomitantly determine the differential degrees of air and environmental contamination by Acinetobacter baumannii based on anatomic source of colonization and type of ICU layout (single-occupancy vs open layout). DESIGN Longitudinal prospective surveillance study of air and environmental surfaces in patient rooms. SETTING A 1,500-bed public teaching hospital in Miami, Florida. PATIENTS Consecutive A. baumannii-colonized patients admitted to our ICUs between October 2013 and February 2014. METHODS Air and environmental surfaces of the rooms of A. baumannii-colonized patients were sampled daily for up to 10 days. Pulsed-field gel electrophoresis (PFGE) was used to type and match the matching air, environmental, and clinical A. baumannii isolates. RESULTS A total of 25 A. baumannii-colonized patients were identified during the study period; 17 were colonized in the respiratory tract and 8 were colonized in the rectum. In rooms with rectally colonized patients, 38.3% of air samples were positive for A. baumannii; in rooms of patients with respiratory colonization, 13.1% of air samples were positive (P=.0001). In rooms with rectally colonized patients, 15.5% of environmental samples were positive for A. baumannii; in rooms of patients with respiratory colonization, 9.5% of environmental samples were positive (P=.02). The rates of air contamination in the open-layout and single-occupancy ICUs were 17.9% and 21.8%, respectively (P=.5). Environmental surfaces were positive in 9.5% of instances in open-layout ICUs versus 13.4% in single-occupancy ICUs (P=.09). CONCLUSIONS Air and environmental surface contaminations were significantly greater among rectally colonized patients; however, ICU layout did not influence the rate of contamination. Infect Control Hosp Epidemiol 2016;37:777-781.

FECAL SOURCE TRACKING BY ANTIBIOTIC RESISTANCE ANALYSIS ON A WATERSHED EXHIBITING LOW RESISTANCE

Science.gov (United States)

The ongoing development of microbial source tracking has made it possible to identify contamination sources with varying accuracy, depending on the method used. The purpose of this study was done to test the efficiency of the antibiotic resistance analysis (ARA) method under low ...

Microbial contamination of disinfectants and antiseptics in four major hospitals in Trinidad

Directory of Open Access Journals (Sweden)

Gajadhar Tswana

2003-01-01

Full Text Available OBJECTIVE: To assess the microbial contamination of disinfectants and antiseptics in major hospitals on the Caribbean island of Trinidad. METHODS: For this cross-sectional study, disinfectants and antiseptics were sampled from the pharmacy departments, the pediatric/neonatal wards, and the surgical wards of four hospitals. The samples were cultured for aerobic bacteria on nutrient agar using the surface plating method. The antibiotic sensitivity of bacterial isolates was determined by the disk diffusion method, using 14 antimicrobial agents. We studied a total of 180 disinfectant/antiseptic samples: 60 of chlorhexidine gluconate (Hibitane, 60 of chlorhexidine gluconate and cetrimonium bromide (Savlon, and 60 of methylated spirit. RESULTS: Of the 180 samples studied, 11 of them (6.1% were contaminated by aerobic bacteria. All bacteria isolated were Pseudomonas spp. Of the 11 contaminated samples, 6 of them (54.5% occurred at the pharmacy level while 5 (45.5% were from diluted pre-use or in-use samples in the pediatric/neonatal wards or the surgical wards. Chlorhexidine gluconate and cetrimonium bromide accounted for 9 of the 11 contaminated disinfectants/antiseptics (81.8%, and chlorhexidine gluconate accounted for the remaining 2 (18.2%. Only two of the four hospitals had contaminated disinfectant/antiseptic samples. All 24 isolates of Pseudomonas spp. tested were resistant to one or more of the 14 antimicrobial agents tested, with the prevalence of resistance to ciprofloxacin, norfloxacin, tobramycin, and gentamicin being 58.3%, 50.0%, 45.8%, and 41.7%, respectively. CONCLUSIONS: Our results show that contaminated disinfectants/antiseptics pose a health risk to patients, particularly in the pediatric and surgical wards. The high prevalence of resistance to antimicrobial agents exhibited by the Pseudomonas spp. that were isolated is of special therapeutic concern.

Microbiology: Barriers to the spread of resistance

DEFF Research Database (Denmark)

Sommer, Morten

2014-01-01

Despite identifying abundant genes capable of conferring antibiotic resistance in soil microorganisms, a study finds that few are shared by human pathogens and that there is little transfer of the genes within the soil communities.......Despite identifying abundant genes capable of conferring antibiotic resistance in soil microorganisms, a study finds that few are shared by human pathogens and that there is little transfer of the genes within the soil communities....

Antibiotic resistant Salmonella and Escherichia coli isolated from ...

African Journals Online (AJOL)

Results: A hundred and four indigenous chicken rectal swabs were analysed, of which 67.3% were contaminated with Escherichia coli and 12.5% with Salmonella typhimurium. Seventy Escherichia coli isolates showed resistance phenotypes to one, two or more antibiotics. The most common antimicrobial resistance pattern ...

Assessment of Environmental Contamination with Pathogenic Bacteria at a Hospital Laundry Facility.

Science.gov (United States)

Michael, Karen E; No, David; Daniell, William E; Seixas, Noah S; Roberts, Marilyn C

2017-11-10

Little is known about exposure to pathogenic bacteria among industrial laundry workers who work with soiled clinical linen. To study worker exposures, an assessment of surface contamination was performed at an industrial laundry facility serving hospitals in Seattle, WA, USA. Surface swab samples (n = 240) from the environment were collected during four site visits at 3-month intervals. These samples were cultured for Clostridium difficile, methicillin-resistant Staphylococcus aureus (MRSA), and vancomycin-resistant enterococci (VRE). Voluntary participation of 23 employees consisted of nasal swabs for detection of MRSA, observations during work, and questionnaires. Contamination with all three pathogens was observed in both dirty (laundry handling prior to washing) and clean areas (subsequent to washing). The dirty area had higher odds of overall contamination (≥1 pathogen) than the clean area (odds ratio, OR = 18.0, 95% confidence interval 8.9-36.5, P contamination were high for each individual pathogen: C. difficile, OR = 15.5; MRSA, OR = 14.8; and VRE, OR = 12.6 (each, P contamination occurred in the primary and secondary sort areas where soiled linens were manually sorted by employees (OR = 63.0, P contaminated by soiled linens. Workers who handle soiled linen may have a higher risk of exposure to C. difficile, MRSA, and VRE than those who handle clean linens. Improved protocols for prevention and reduction of environmental contamination were implemented because of this study. © The Author 2017. Published by Oxford University Press on behalf of the British Occupational Hygiene Society.

Antibiotic resistance of microorganisms in agricultural soils in Russia

Science.gov (United States)

Danilova, Natasha; Galitskaya, Polina; Selivanovskaya, Svetlana

2017-04-01

Antibiotics are medicines widely used to treat and prevent bacterial infections not only in human medicine but also in veterinary. Besides, in animal husbandry antibiotics are often used in for stimulation of animal's growth. Many antibiotics used for veterinary purposes are weakly absorbed in the animal's gut. So up to 90% of the administered antibiotics are excreted with manure and urine. Therefore use of manure as an organic fertilizer leads to formation and spreading of antibiotic resistance among soil microbes. Another reason of such spreading is the horizontal transfer of genes encoding antibiotic resistance from manure to soil microflora. The level of antibiotic resistance genes pollution of soils has not been properly studied yet. The aim of this study was to estimate the contamination of agricultural soils by antibiotic resistant genes. 30 samples of agricultural soils were selected around of Kazan city (Tatarstan Republic) with 1.3 Mio citizens. Since tetracycline is reported to be the most wide spread veterinary antibiotic in Russia, we estimated the level of soil contamination by tet(X) gene encoding tetracycline decomposition in microbial cell. Real time PCR method with specific primers was used as a method of investigation. Particle size type distribution of 31% of soil samples was estimated to be sandy clay, and 69% of soil samples - to silty clay. Content of dissoluble organic carbon ranged from 0,02 mg g -1 (sample 20) to 0,46 mg g -1 (sample 16). Respiration activity and microbial biomass of soils were estimated to be 0,80-5,28 CO2 C mg g -1 h-1 and 263,51-935,77 µg kg - 1 respectively. The values presented are typical for soils of Tatarstan Republic. In terms of the antibiotic resistant gene content, 27 of 30 samples investigated contained tet(X) gene, while 52% of the samples were highly contaminated, 34% of samples were middle contaminated and 14% of samples - weakly contaminated.

Noninvasive characterization of the Trecate (Italy) crude-oil contaminated site: links between contamination and geophysical signals.

Science.gov (United States)

Cassiani, Giorgio; Binley, Andrew; Kemna, Andreas; Wehrer, Markus; Orozco, Adrian Flores; Deiana, Rita; Boaga, Jacopo; Rossi, Matteo; Dietrich, Peter; Werban, Ulrike; Zschornack, Ludwig; Godio, Alberto; JafarGandomi, Arash; Deidda, Gian Piero

2014-01-01

The characterization of contaminated sites can benefit from the supplementation of direct investigations with a set of less invasive and more extensive measurements. A combination of geophysical methods and direct push techniques for contaminated land characterization has been proposed within the EU FP7 project ModelPROBE and the affiliated project SoilCAM. In this paper, we present results of the investigations conducted at the Trecate field site (NW Italy), which was affected in 1994 by crude oil contamination. The less invasive investigations include ground-penetrating radar (GPR), electrical resistivity tomography (ERT), and electromagnetic induction (EMI) surveys, together with direct push sampling and soil electrical conductivity (EC) logs. Many of the geophysical measurements were conducted in time-lapse mode in order to separate static and dynamic signals, the latter being linked to strong seasonal changes in water table elevations. The main challenge was to extract significant geophysical signals linked to contamination from the mix of geological and hydrological signals present at the site. The most significant aspects of this characterization are: (a) the geometrical link between the distribution of contamination and the site's heterogeneity, with particular regard to the presence of less permeable layers, as evidenced by the extensive surface geophysical measurements; and (b) the link between contamination and specific geophysical signals, particularly evident from cross-hole measurements. The extensive work conducted at the Trecate site shows how a combination of direct (e.g., chemical) and indirect (e.g., geophysical) investigations can lead to a comprehensive and solid understanding of a contaminated site's mechanisms.

Study of magnetorheology and sensing capabilities of MR elastomers

International Nuclear Information System (INIS)

Tian, T F; Li, W H; Alici, G

2013-01-01

This study focuses on the magnetorheology and sensing capability of graphite based Magnetorheological Elastomers (Gr MREs). By introducing graphite (Gr) to conventional MREs, the Gr MREs are derived. The anisotropic sample with 20% graphite weight fraction was selected to be compared with anisotropic conventional MREs. The microstructures of anisotropic Gr MREs and conventional MREs were observed. Both steady state tests and dynamic tests were conducted to study rheological properties of the samples. For dynamic tests, the effects of strain amplitude, and frequency on both storage modulus and loss modulus were measured. For sensing capability, the resistance of selected Gr MREs under different magnetic fields and external loadings is measured with a multi-meter. Either higher magnetic field or more external loading results in the resistance increment. Based on an ideal assumption of perfect chain structure, a mathematical model was proposed to investigate the relationship between the MRE resistance with the external loadings. In this model, the current flowing through the chain structure consists of both tunnel current and conductivity current, both of which depends on external loadings. The modelling parameters were identified and reconstructed from comparison with experimental results. The comparison indicates that both experimental results and modelling prediction agree favourably well.

Purification of oil-contaminated soils from heavy metals using plants

International Nuclear Information System (INIS)

Zamanova, A.

2014-01-01

Full text : Purification of local areas of oil-contaminated soils with contamination degree of 5-8 percent using plant resistant to salinity and high temperature and rehabilitation of these soils is the most urgent task for Apsheron Peninsula which is the main territory of oil onshore in Azerbaijan. This method is environmentally compatible and economically viable against other methods. Despite the fact that in this area it has been carried out numerous scientific researches, for each level of contamination, for each specific soil type, for each specific climatic conditions and the group of plants requires more and more researches

Electrical resistivity for detecting subsurface non-aqueous phase liquids: A progress report

International Nuclear Information System (INIS)

Lee, K.H.; Shan, C.; Javandel, I.

1995-06-01

Soils and groundwater have been contaminated by hazardous substances at many places in the United States and many other countries. The contaminants are commonly either petroleum products or industrial solvents with very low solubility in water. These contaminants are usually called non-aqueous phase liquids (NAPLs). The cost of cleaning up the affected sites in the United States is estimated to be of the order of 100 billion dollars. In spite of the expenditure of several billion dollars during the last 15 years, to date, very few, if any major contaminated site has been restored. The presence of NAPL pools in the subsurface is believed to be the main cause for the failure of previous cleanup activities. Due to their relatively low water solubility, and depending on their volume, it takes tens or even hundreds of years to deplete the NAPL sources if they are not removed from the subsurface. The intrinsic electrical resistivity of most NAPLs is typically in the range of 10 7 to 10 12 Ω-m, which is several orders of magnitude higher than that of groundwater containing dissolved solids (usually in the range of a few Ω-m to a few thousand Ω-m). Although a dry soil is very resistive, the electrical resistivity of a wet soil is on the order of 100 Ω-m and is dependent on the extent of water saturation. For a given soil, the electrical resistivity increases with decrease of water saturation. Therefore, if part of the pore water is replaced by a NAPL, the electrical resistivity will increase. At many NAPL sites, both the vadose and phreatic zones can be partially occupied by NAPL pools. It is the great contrast in electrical resistivity between the NAPLs and groundwater that may render the method to be effective in detecting subsurface NAPLs at contaminated sites. The following experiments were conducted to investigate the change of the electrical resistivity of porous media when diesel fuel (NAPL) replaces part of the water

Multiple antibiotic resistance patterns of rhizospheric bacteria isolated from Phragmites australis growing in constructed wetland for distillery effluent treatment.

Science.gov (United States)

Chaturvedi, Sonal; Chandra, Ram; Rai, Vibhuti

2008-01-01

Susceptibility patterns of 12 different antibiotics were investigated against rhizospheric bacteria isolated from Phragmites australis from three different zones i.e. upper (0-5 cm), middle (5-10 cm), lower (10-15 cm) in constructed wetland system with and without distillery effluent. The major pollutants of distillery effluent were phenols, sulphide, heavy metals, and higher levels of biological oxygen demand (BOD), chemical oxygen demand (COD) etc. The antibiotic resistance properties of bacteria were correlated with the heavy metal tolerance (one of distillery pollutant). Twenty-two species from contaminated and seventeen species from non-contaminated site were tested by agar disc-diffusion method. The results revealed that more than 63% of total isolates were resistance towards one or more antibiotics tested from all the three different zones of contaminated sites. The multiple-drug resistance property was shown by total 8 isolates from effluent contaminated region out of which 3 isolates were from upper zone, 3 isolates from middle zone and 2 isolates were from lower zone. Results indicated that isolates from contaminated rhizosphere were found more resistant to antibiotics than isolates from non-contaminated rhizosphere. Further this study produces evidence suggesting that tolerance to antibiotics was acquired by isolates for the adaptation and detoxification of all the pollutants present in the effluent at contaminated site. This consequently facilitated the phytoremediation of effluent, which emerges the tolerance and increases resistance to antibiotics.

Performance testing of the sediment-contaminant transport model, SERATRA, at different rivers

International Nuclear Information System (INIS)

Onishi, Y.; Yabusaki, S.B.; Kincaid, C.T.

1982-04-01

Mathematical models of sediment-contaminant migration in surface water must account for transport, intermedia transfer, decay and degradation, and transformation processes. The unsteady, two dimensional, sediment-contaminant transport code, SERATRA (Onishi, Schreiber and Codell 1980) includes these mechanisms. To assess the accuracy of SERATRA to simulate the sediment-contaminant transport and fate processes, the code was tested against one-dimensional analytical solutions, checked for its mass balance, and applied to field sites. The field application cases ranged from relatively simple, steady conditions to unsteady, nonuniform conditions for large, intermediate, and small rivers. It was found that SERATRA is capable of simulating sediment-contaminant transport under a wide range of conditions

Remediating Contaminant Plumes in Groundwater with Shallow Excavations Containing Coarse Reactive Media.

Science.gov (United States)

Hudak, Paul F

2018-02-01

A groundwater flow and mass transport model tested the capability of shallow excavations filled with coarse, reactive media to remediate a hypothetical unconfined aquifer with a maximum saturated thickness of 5 m. Modeled as contaminant sinks, the rectangular excavations were 10 m downgradient of an initial contaminant plume originating from a source at the top of the aquifer. The initial plume was approximately 259 m long, 23 m wide, and 5 m thick, with a downgradient tip located approximately 100 m upgradient of the site boundary. The smallest trench capable of preventing offsite migration was 11 m long (measured perpendicular to groundwater flow), 4 m wide (measured parallel to groundwater flow), and 3 m deep. Results of this study suggest that shallow trenches filled with coarse filter media that partially penetrate unconfined aquifers may be a viable alternative for remediating contaminated groundwater at some sites.

Contamination pathways of spore-forming bacteria in a vegetable cannery.

Science.gov (United States)

Durand, Loïc; Planchon, Stella; Guinebretiere, Marie-Hélène; André, Stéphane; Carlin, Frédéric; Remize, Fabienne

2015-06-02

Spoilage of low-acid canned food during prolonged storage at high temperatures is caused by heat resistant thermophilic spores of strict or facultative bacteria. Here, we performed a bacterial survey over two consecutive years on the processing line of a French company manufacturing canned mixed green peas and carrots. In total, 341 samples were collected, including raw vegetables, green peas and carrots at different steps of processing, cover brine, and process environment samples. Thermophilic and highly-heat-resistant thermophilic spores growing anaerobically were counted. During vegetable preparation, anaerobic spore counts were significantly decreased, and tended to remain unchanged further downstream in the process. Large variation of spore levels in products immediately before the sterilization process could be explained by occasionally high spore levels on surfaces and in debris of vegetable combined with long residence times in conditions suitable for growth and sporulation. Vegetable processing was also associated with an increase in the prevalence of highly-heat-resistant species, probably due to cross-contamination of peas via blanching water. Geobacillus stearothermophilus M13-PCR genotypic profiling on 112 isolates determined 23 profile-types and confirmed process-driven cross-contamination. Taken together, these findings clarify the scheme of contamination pathway by thermophilic spore-forming bacteria in a vegetable cannery. Copyright © 2015 Elsevier B.V. All rights reserved.

Fermented whey as poultry feed additive to prevent fungal contamination.

Science.gov (United States)

Londero, Alejandra; León Peláez, María A; Diosma, Gabriela; De Antoni, Graciela L; Abraham, Analía G; Garrote, Graciela L

2014-12-01

Fungal contamination of poultry feed causes economic losses to industry and represents a potential risk to animal health. The aim of the present study was to analyze the effectiveness of whey fermented with kefir grains as additive to reduce fungal incidence, thus improving feed safety. Whey fermented for 24 h at 20 °C with kefir grains (100 g L(-1) ) reduced conidial germination of Aspergillus flavus, Aspergillus parasiticus, Aspergillus terreus, Aspergillus fumigatus, Penicillium crustosum, Trichoderma longibrachiatum and Rhizopus sp. Poultry feed supplemented with fermented whey (1 L kg(-1) ) was two to four times more resistant to fungal contamination than control feed depending on the fungal species. Additionally, it contained kefir microorganisms at levels of 1 × 10(8) colony-forming units (CFU) kg(-1) of lactic acid bacteria and 6 × 10(7) CFU kg(-1) of yeasts even after 30 days of storage. Fermented whey added to poultry feed acted as a biopreservative, improving its resistance to fungal contamination and increasing its shelf life. © 2014 Society of Chemical Industry.

OCCURRENCE OF MERCURY-RESISTANT MICROORGANISMS IN MERCURY-CONTAMINATED SOILS AND SEDIMENTS IN PAVLODAR, KAZAKHSTAN

Science.gov (United States)

There is extensive mercury contamination of soil surrounding a chloralkali plant in Pavlodar, Kazakhstan that operated from 1970 to 1990. High-level mercury contamination exists within the confines of the plant, at nearby off-site waste storage and evaporation ponds, and in Balky...

Bioremediation of Pyrene-Contaminated Soils Using Biosurfactant

Directory of Open Access Journals (Sweden)

Jorfi

2014-10-01

Full Text Available Background Polycyclic aromatic hydrocarbons (PAHs are persistence organic chemicals with proved carcinogenic and mutagenic hazards. These compounds are usually adsorbed in soils in vicinity of oil and gas industries. Bioremediation of PAHs contaminated soils is difficult due to hydrophobic nature of PAHs. Objectives The main purpose of the current study was to determine the pyrene removal efficiency in synthetically contaminated soil, using biosurfactant. Materials and Methods Four pure bacterial strains capable of pyrene degradation were isolated from contaminated soils via enrichment techniques. The soil samples were spiked with an initial pyrene concentration of 500 mg/kg and subjected to bioremediation using a mixed culture comprised of previously isolated strains, in addition to application of biosurfactant during 63 days. Results The pyrene removal efficiency in samples containing biosurfactant, without biosurfactant and controls, were 86.4%, 59.8% and 14%, respectively, after 63 days. The difference of pyrene removal efficiency between the biosurfactant-containing samples and the ones without it was significant (P < 0.05. Conclusions Application of rhamnolipid biosurfactant produced by Pseudomonas aeruginosa significantly improved pyrene removal in contaminated soils.

Treatment of chromium contaminated soil using bioremediation

Science.gov (United States)

Purwanti, Ipung Fitri; Putri, Tesya Paramita; Kurniawan, Setyo Budi

2017-11-01

Chromium contamination in soil occurs due to the disposal of chromium industrial wastewater or sludge that excess the quality standard. Chromium concentration in soil is ranged between 1 to 300 mg/kg while the maximum health standard is 2.5 mg/kg. Bioremediation is one of technology that could be used for remediating heavy metal contamination in soil. Bacteria have an ability to remove heavy metal from soil. One bacteria species that capable to remove chromium from soil is Bacillus subtilis. The aim of this research was to know the chromium removal percentage in contaminated soil by Bacillus subtilis. Artificial chromium contaminated soil was used by mixing 425gram sand and chromium trichloride solution. Concentration of chromium added into the spiked soil were 50, 75, and 100 mg/L. During 14 days, pH, soil temperature and soil moisture were tested. Initial and final number of bacterial colony and chromium concentration analysed. The result showed that the highest percentage of chromium removal was 11% at a chromium concentration of 75 mg/L

Antibiotic-Resistant Enteric Bacteria in Environmental Waters

Directory of Open Access Journals (Sweden)

Lisa M. Casanova

2016-11-01

Full Text Available Sources of antibiotic resistant organisms, including concentrated animal feeding operations (CAFOs, may lead to environmental surface and groundwater contamination with resistant enteric bacteria of public health concern. The objective of this research is to determine whether Salmonella, Escherichia coli, Yersinia enterocolitica, and enterococci resistant to clinically relevant antibiotics are present in surface and groundwater sources in two eastern North Carolina counties, Craven and Wayne. 100 surface and groundwater sites were sampled for Salmonella, E. coli, and enterococci, and the bacteria isolated from these samples were tested for susceptibility to clinically relevant antibiotics. Salmonella were detected at low levels in some surface but not groundwater. E. coli were in surface waters but not ground in both counties. Enterococci were present in surface water and a small number of groundwater sites. Yersinia was not found. Bacterial densities were similar in both counties. For Salmonella in surface water, the most frequent type of resistance was to sulfamethoxazole. There was no ciprofloxacin resistance. There were a few surface water E. coli isolates resistant to chloramphenicol, gentamicin, and ampicillin. Enterococci in surface water had very low levels of resistance to vancomycin, chloramphenicol, ampicillin, and streptomycin. E. coli and enterococci are present more frequently and at higher levels in surface water than Salmonella, but groundwater contamination with any of these organisms was rare, and low levels of resistance can be found sporadically. Resistant bacteria are relatively uncommon in these eastern N.C. surface and groundwaters, but they could pose a risk of human exposure via ingestion or primary contact recreation.

Addition of liquid waste incineration capability to the INEL's low-level waste incinerator

International Nuclear Information System (INIS)

Steverson, E.M.; Clark, D.P.; McFee, J.N.

1986-01-01

A liquid waste system has recently been installed in the Waste Experimental Reduction Facility (WERF) incinerator at the Idaho National Engineering Laboratory (INEL). In this paper, aspects of the incineration system such as the components, operations, capabilities, capital cost, EPA permit requirements, and future plans are discussed. The principal objective of the liquid incineration system is to provide the capability to process hazardous, radioactively contaminated, non-halogenated liquid wastes. The system consists primarily of a waste feed system, instrumentation and controls, and a liquid burner, which were procured at a capital cost of $115,000

Norwegian patients and retail chicken meat share cephalosporin-resistant Escherichia coli and IncK/blaCMY-2 resistance plasmids

DEFF Research Database (Denmark)

Berg, E. S.; Wester, A. L.; Ahrenfeldt, Johanne

2017-01-01

In 2012 and 2014 the Norwegian monitoring programme for antimicrobial resistance in the veterinary and food production sectors (NORM-VET) showed that 124 of a total of 406 samples (31%) of Norwegian retail chicken meat was contaminated with extended-spectrum cephalosporin-resistant Escherichia coli....... The aim of this study was to compare selected cephalosporin-resistant E. coli from humans and poultry to determine their genetic relatedness based on whole genome sequencing (WGS). E. coli representing three prevalent cephalosporin-resistant multi-locus sequence types (STs) isolated from poultry (n=17...

Remediation of PAH-contaminated soil using Achromobacter sp

International Nuclear Information System (INIS)

Cutright, T.J.; Lee, S.

1994-01-01

Several technologies have the potential to effectively remediate soil contaminated with polycyclic aromatic hydrocarbons (PAHs): solvent extraction, coal-oil agloflotation, supercritical extraction, and bioremediation. Due to the cost effectiveness and in-situ treatment capabilities of bioremediation, studies were conducted to determine the efficiency of Achromobacter sp. to remediate an industrial contaminated soil sample. Specifically, the use of three different mineral salt solutions in conjunction with the Achromobacter sp. was investigated. The molecular identification of the contaminants and their respective levels after remediation were determined using a Hewlett-Packard 1050 HPLC. Preliminary results show a 92% remediation for the use of two of the mineral salt solutions after 20 days' treatment. After 8 weeks, the remediation efficiency reached 99%. Bioremediation was also critically compared to the other potential remediation technologies

Antimicrobial resistance and resistance genes in Salmonella strains isolated from broiler chickens along the slaughtering process in China.

Science.gov (United States)

Zhu, Yuanting; Lai, Haimei; Zou, Likou; Yin, Sheng; Wang, Chengtao; Han, Xinfeng; Xia, Xiaolong; Hu, Kaidi; He, Li; Zhou, Kang; Chen, Shujuan; Ao, Xiaolin; Liu, Shuliang

2017-10-16

A1 (19 isolates) and bla OXA-30 -aadA1/drfA1-orfC (2 isolates), were identified in class 1 integron-positive isolates. 97.9% (184/188) of quinolone-resistant isolates had at least one mutation within gyrA or parC. Overall, antimicrobial resistance showed an increasing trend along the slaughtering process. The results showed that broiler chicken products in the slaughterhouse were contaminated with MDR Salmonella, which might originate from food producing animals to some extent, and cross-contamination during slaughter, and facilitate the dissemination of the resistance genes to consumers along the production chain, which suggests importance of controlling Salmonella during slaughter for public health, underlying strict hygiene method and HACCP management to reduce cross-contamination. Copyright © 2017 Elsevier B.V. All rights reserved.

A Consideration of Resistance and Tolerance for Ruminant Nematode Infections

Directory of Open Access Journals (Sweden)

Steve eBishop

2012-12-01

Full Text Available Debates on the relative merits of resistance (the ability of the host to control the parasite lifecycle and tolerance (the net impact of infection on host performance are often lively and unhindered by data or evidence. Resistance generally shows continuous, heritable variation but data are sparser for tolerance, the utility of which will depend upon the disease prevalence. Prevalence is a function of group mean resistance and infection pressure, which itself is influenced by mean resistance. Tolerance will have most value for endemic diseases with a high prevalence, but will be of little value for low prevalence diseases. The conditionality of tolerance on infection status, and hence resistance, makes it difficult to estimate independently of resistance.Tolerance is potentially tractable for nematode infections, as the prevalence of infection is ca. 100% in animals grazing infected pasture, and infection level can be quantified by faecal egg count (FEC. Whilst individual animal phenotypes for tolerance are difficult to estimate, breeding values are estimable if related animals graze pastures of different contamination levels. Selection for resistance, i.e. FEC, provides both direct and indirect benefits from ever decreased pasture contamination and hence decreased infectious challenge. Modelling and experimental studies have shown that such reductions in pasture contamination may lead to substantially increased performance.It is proposed that selection goals addressing nematode infections should include both resistance and performance under challenging conditions. However, there may be benefits from exploiting large datasets in which sires are used across cohorts differing in infection level, to further explore tolerance. This may help to customise breeding objectives, with tolerance given greater weight in heavily parasitized environments.

Arsenic-resistant and plant growth-promoting Firmicutes and γ-Proteobacteria species from industrially polluted irrigation water and corresponding cropland.

Science.gov (United States)

Qamar, N; Rehman, Y; Hasnain, S

2017-09-01

The aim of the study was to explore irrigation water polluted with industrial waste and corresponding cropland to screen bacteria for As detoxification and plant growth promotion. Plant growth-promoting (PGP) As-resistant cropland bacteria were isolated from contaminated irrigation water and corresponding agricultural soil. Phylogenetic analysis revealed that the isolates belonged to two distinct bacterial lineages; Firmicutes and γ-Proteobacteria. Maximum As(V) resistance was exhibited by Klebsiella pneumoniae T22 and Klebsiella oxytoca N53 (550 mmol l -1 ), whereas maximum resistance against As(III) was exhibited by K. oxytoca N53 (200 mmol l -1 ). Maximum As(V) reduction was shown by K. pneumoniae T22 (6·7 mmol l -1 ), whereas maximum As(III) oxidation was exhibited by Bacillus subtilis T23 (4·8 mmol l -1 ). As resistance genes arsB and ACR3 were detected in many of the isolates through polymerase chain reaction. Many of these isolates exhibited PGP traits such as hydrogen cyanide and auxin production as well as phosphate solubilization. The bacterial strains were able to enhance Triticum aestivum growth both in the absence and presence of As, and statistically significant increase in shoot and root lengths was observed especially in case of Acinetobacter lwoffii T24 and Citrobacter freundii N52-treated plants. Cropland bacteria have the ability to support plant growth. Bacteria of croplands irrigated with industrially polluted water develop resistance against toxicants. These bacteria are helpful for the plant growth in such contaminated lands. The bacteria capable of both As detoxification and plant growth promotion, such as A. lwoffii T24 and C. freundii N52, are ideal for remediation and reclamation of polluted lands for agriculture purposes. © 2017 The Society for Applied Microbiology.

Non-targeted analysis of unexpected food contaminants using LC-HRMS.

Science.gov (United States)

Kunzelmann, Marco; Winter, Martin; Åberg, Magnus; Hellenäs, Karl-Erik; Rosén, Johan

2018-03-29

A non-target analysis method for unexpected contaminants in food is described. Many current methods referred to as "non-target" are capable of detecting hundreds or even thousands of contaminants. However, they will typically still miss all other possible contaminants. Instead, a metabolomics approach might be used to obtain "true non-target" analysis. In the present work, such a method was optimized for improved detection capability at low concentrations. The method was evaluated using 19 chemically diverse model compounds spiked into milk samples to mimic unknown contamination. Other milk samples were used as reference samples. All samples were analyzed with UHPLC-TOF-MS (ultra-high-performance liquid chromatography time-of-flight mass spectrometry), using reversed-phase chromatography and electrospray ionization in positive mode. Data evaluation was performed by the software TracMass 2. No target lists of specific compounds were used to search for the contaminants. Instead, the software was used to sort out all features only occurring in the spiked sample data, i.e., the workflow resembled a metabolomics approach. Procedures for chemical identification of peaks were outside the scope of the study. Method, study design, and settings in the software were optimized to minimize manual evaluation and faulty or irrelevant hits and to maximize hit rate of the spiked compounds. A practical detection limit was established at 25 μg/kg. At this concentration, most compounds (17 out of 19) were detected as intact precursor ions, as fragments or as adducts. Only 2 irrelevant hits, probably natural compounds, were obtained. Limitations and possible practical use of the approach are discussed.

Enzymatic bioremediation of polyaromatic hydrocarbons by fungal consortia enriched from petroleum contaminated soil and oil seeds.

Science.gov (United States)

Balaji, V; Arulazhagan, P; Ebenezer, P

2014-05-01

The present study focuses on fungal strains capable of secreting extracellular enzymes by utilizing hydrocarbons present in the contaminated soil. Fungal strains were enriched from petroleum hydrocarbons contaminated soil samples collected from Chennai city, India. The potential fungi were isolated and screened for their enzyme secretion such as lipase, laccase, peroxidase and protease and also evaluated fungal enzyme mediated PAHs degradation. Total, 21 potential PAHs degrading fungi were isolated from PAHs contaminated soil, which belongs to 9 genera such as Aspergillus, Curvularia, Drechslera, Fusarium, Lasiodiplodia, Mucor Penicillium, Rhizopus, Trichoderma, and two oilseed-associated fungal genera such as Colletotrichum and Lasiodiplodia were used to test their efficacy in degradation of PAHs in polluted soil. Maximum lipase production was obtained with P. chrysogenum, M. racemosus and L. theobromae VBE1 under optimized cultural condition, which utilized PAHs in contaminated soil as sole carbon source. Fungal strains, P. chrysogenum, M. racemosus and L. theobromae VBE1, as consortia, used in the present study were capable of degrading branched alkane isoprenoids such as pristine (C17) and pyrene (C18) present in PAHs contaminated soil with high lipase production. The fungal consortia acts as potential candidate for bioremediation of PAHs contaminated environments.

Protists from a sewage‐contaminated aquifer on cape cod, Massachusetts

Science.gov (United States)

Novarino, Gianfranco; Warren, Alan; Kinner, Nancy E.; Harvey, Ronald W.

1994-01-01

Several species of flagellates (genera Bodo, Cercomonas, Cryptaulax, Cyathomonas, Goniomonas, Spumella) have been identified in cultures from a plume of organic contamination (treated sewage effluent) within an aquifer on Cape Cod, Massachusetts. Amoebae and numerous unidentifiable 2‐ to 3‐μm flagellates have also been observed. As a rule, flagellates were associated with solid surfaces, or were capable of temporary surface attachment, corroborating earlier observations from in situ and column transport experiments suggesting that protists in the Massachusetts aquifer have a high propensity for association with sediment grain surfaces. Based on the fact that cultures from the uncontaminated part of the aquifer yielded only a few species of protists, it is hypothesized that the greater abundance and variety of food sources in the contaminant plume is capable of supporting a greater number of protistan species.

Trace Contaminant Control During the International Space Station's On-Orbit Assembly and Outfitting

Science.gov (United States)

Perry, J. L.

2017-01-01

Achieving acceptable cabin air quality must balance competing elements during spacecraft design, assembly, ground processing, and flight operations. Among the elements that contribute to the trace chemical contaminant load and, therefore, the cabin air quality aboard crewed spacecraft are the vehicle configuration, crew size and activities, mission duration and objectives, materials selection, and vehicle manufacturing and preflight ground processing methods. Trace chemical contaminants produced from pervasive sources such as equipment offgassing, human metabolism, and cleaning fluids during preflight ground processing present challenges to maintaining acceptable cabin air quality. To address these challenges, both passive and active contamination control techniques are used during a spacecraft's design, manufacturing, preflight preparation, and operational phases. Passive contamination control methods seek to minimize the equipment offgassing load by selecting materials, manufacturing processes, preflight preparation processes, and in-flight operations that have low chemical offgassing characteristics. Passive methods can be employed across the spacecraft's entire life cycle from conceptual design through flight operations. However, because the passive contamination control techniques cannot fully eliminate the contaminant load, active contamination control equipment must be deployed aboard the spacecraft to purify and revitalize the cabin atmosphere during in-flight operations. Verifying that the passive contamination control techniques have successfully maintained the total trace contaminant load within the active contamination control equipment's capabilities occurs late in the preflight preparation stages. This verification consists of subjecting the spacecraft to an offgassing test to determine the trace contaminant load. This load is then assessed versus the active contamination control equipment's capabilities via trace contaminant control (TCC) engineering

Functional gene array-based analysis of microbial community structure in groundwaters with a gradient of contaminant levels

Energy Technology Data Exchange (ETDEWEB)

Waldron, P.J.; Wu, L.; Van Nostrand, J.D.; Schadt, C.W.; Watson, D.B.; Jardine, P.M.; Palumbo, A.V.; Hazen, T.C.; Zhou, J.

2009-06-15

To understand how contaminants affect microbial community diversity, heterogeneity, and functional structure, six groundwater monitoring wells from the Field Research Center of the U.S. Department of Energy Environmental Remediation Science Program (ERSP; Oak Ridge, TN), with a wide range of pH, nitrate, and heavy metal contamination were investigated. DNA from the groundwater community was analyzed with a functional gene array containing 2006 probes to detect genes involved in metal resistance, sulfate reduction, organic contaminant degradation, and carbon and nitrogen cycling. Microbial diversity decreased in relation to the contamination levels of the wells. Highly contaminated wells had lower gene diversity but greater signal intensity than the pristine well. The microbial composition was heterogeneous, with 17-70% overlap between different wells. Metal-resistant and metal-reducing microorganisms were detected in both contaminated and pristine wells, suggesting the potential for successful bioremediation of metal-contaminated groundwaters. In addition, results of Mantel tests and canonical correspondence analysis indicate that nitrate, sulfate, pH, uranium, and technetium have a significant (p < 0.05) effect on microbial community structure. This study provides an overall picture of microbial community structure in contaminated environments with functional gene arrays by showing that diversity and heterogeneity can vary greatly in relation to contamination.

Prevalence and antibiotic-resistance characteristics of Enterococcus spp. Isolated from free-living and captive raptors in Central Illinois.

Science.gov (United States)

Marrow, Judilee; Whittington, Julia K; Mitchell, Mark; Hoyer, Lois L; Maddox, Carol

2009-04-01

Due to their predatory nature, raptor species may serve as important indicators of environmental contamination with antimicrobial-resistant bacteria. Raptors prey on small rodents and birds that have diverse habitat ranges, including urban and rural environments, and their intestinal microflora can reflect that of the animals on which they feed. Enterococcus spp. were selected as target organisms because they have been isolated from the avian gastrointestinal tract, can be conferred by prey items, and because they are capable of multiple resistance patterns. They are also a concerning source of human antimicrobial resistance. In this study fecal cultures were obtained from 15 May 2004 to 31 August 2004, from 21 free-living raptors and four captive raptors. Enterococcus was isolated from 21 (84%) of the 25 birds, and 54 isolates were chosen for further study based upon unique colony morphology. The most common isolate recovered was Enterococcus faecalis (95%, 95% confidence interval [CI]: 89-100). One bird in the study was determined to have Enterococcus gallinarum. Two distinct ribotypes of E. faecalis were identified, one with unique bands at 11 and 13 kb and the other with unique bands at 14 and 20 kb. Both ribotypes were found in free-living and captive birds. The Enterococcus isolates in this study demonstrated a variety of antimicrobial-resistance characteristics, including almost complete resistance to amikacin, first-generation cephalosporins, spectinomycin, and sulphadimethoxime. Isolates demonstrated variable resistance to chloramphenicol, gentamicin, enrofloxacin, erythromycin, and ticarcillin. No phenotypically vancomycin-resistant E. faecalis isolates were recovered from any of the raptors; three isolates had intermediate level susceptibility. A significantly higher number of isolates collected from captive birds demonstrated resistance to chloramphenicol than those obtained from free-living birds. This trend was not duplicated with any of the remaining

Environmental pollution by antibiotics and by antibiotic resistance determinants

International Nuclear Information System (INIS)

Martinez, Jose Luis

2009-01-01

Antibiotics are among the most successful drugs used for human therapy. However, since they can challenge microbial populations, they must be considered as important pollutants as well. Besides being used for human therapy, antibiotics are extensively used for animal farming and for agricultural purposes. Residues from human environments and from farms may contain antibiotics and antibiotic resistance genes that can contaminate natural environments. The clearest consequence of antibiotic release in natural environments is the selection of resistant bacteria. The same resistance genes found at clinical settings are currently disseminated among pristine ecosystems without any record of antibiotic contamination. Nevertheless, the effect of antibiotics on the biosphere is wider than this and can impact the structure and activity of environmental microbiota. Along the article, we review the impact that pollution by antibiotics or by antibiotic resistance genes may have for both human health and for the evolution of environmental microbial populations. - The article reviews the current knowledge on the effects that pollution by antibiotics and antibiotic resistance genes may have for the microbiosphere.

Environmental pollution by antibiotics and by antibiotic resistance determinants

Energy Technology Data Exchange (ETDEWEB)

Martinez, Jose Luis, E-mail: jlmtnez@cnb.csic.e [Departamento de Biotecnologia Microbiana, Centro Nacional de Biotecnologia, Consejo Superior de Investigaciones Cientificas, Darwin 3, Cantoblanco, 28049 Madrid, and CIBERESP (Spain)

2009-11-15

Antibiotics are among the most successful drugs used for human therapy. However, since they can challenge microbial populations, they must be considered as important pollutants as well. Besides being used for human therapy, antibiotics are extensively used for animal farming and for agricultural purposes. Residues from human environments and from farms may contain antibiotics and antibiotic resistance genes that can contaminate natural environments. The clearest consequence of antibiotic release in natural environments is the selection of resistant bacteria. The same resistance genes found at clinical settings are currently disseminated among pristine ecosystems without any record of antibiotic contamination. Nevertheless, the effect of antibiotics on the biosphere is wider than this and can impact the structure and activity of environmental microbiota. Along the article, we review the impact that pollution by antibiotics or by antibiotic resistance genes may have for both human health and for the evolution of environmental microbial populations. - The article reviews the current knowledge on the effects that pollution by antibiotics and antibiotic resistance genes may have for the microbiosphere.

Pilot study on multidrug resistant tuberculosis in Nigeria

African Journals Online (AJOL)

and 4 were deemed to be contaminants, leaving 35 specimens for analysis of DST. DST was performed in 32 of the 35 isolates; 10 (31%) were resistant to at least one of .... (PCR) technologies that are emerging elsewhere. Future studies should investigate if extensively drug resistant TB (XDR-TB) strains are also affecting.

Trophic-metabolic activity of earthworms (Lumbricidae as a zoogenic factor of maintaining reclaimed soils’ resistance to copper contamination

Directory of Open Access Journals (Sweden)

Y. L. Kulbachko

2014-07-01

which restricts movement of excess chemicals, maintains stability and increases resistance to soil contamination, in particular, with copper. Besides, it is possible to accelerate the artificial forest edaphotop naturalization on reclaimed land, and to increase its ecological value

Removal of residual contaminants in petroleum-contaminated soil by Fenton-like oxidation

Energy Technology Data Exchange (ETDEWEB)

Lu Mang [School of Material Science and Engineering, Jingdezhen Ceramic Institute, Jingdezhen, 333001, Jiangxi Province (China); State Key Laboratory of Heavy Oil Processing, China University of Petroleum, Beijing 102249 (China); Zhang Zhongzhi, E-mail: zzzhang1955@hotmail.com [State Key Laboratory of Heavy Oil Processing, China University of Petroleum, Beijing 102249 (China); Qiao Wei; Guan Yueming; Xiao Meng; Peng Chong [State Key Laboratory of Heavy Oil Processing, China University of Petroleum, Beijing 102249 (China)

2010-07-15

The degradation of bioremediation residues by hydrogen peroxide in petroleum-contaminated soil was investigated at circumneutral pH using a Fenton-like reagent (ferric ion chelated with EDTA). Batch tests were done on 20 g soil suspended in 60 mL aqueous solution containing hydrogen peroxide and Fe{sup 3+}-EDTA complex under constant stirring. A slurry reactor was used to treat the soil based on the optimal reactant conditions. Contaminants were characterized by Fourier transform infrared spectroscopy and Fourier transform ion cyclotron resonance mass spectrometry. The results showed that the optimal treatment condition was: the molar ratio of hydrogen peroxide to iron = 200:1, and pH 7.0. Under the optimum condition, total dichloromethane-extractable organics were reduced from 14,800 to 2300 mg kg{sup -1} soil when the accumulative H{sub 2}O{sub 2} dosage was 2.45 mol kg{sup -1} soil during the reactor treatment. Abundance of viable cells was lower in incubated Fenton-like treated soil than in untreated soil. Oxidation of contaminants produced remarkable compositional and structural modifications. A fused ring compound, identified as C{sub 34}H{sub 38}N{sub 1}, was found to exhibit the greatest resistance to oxidation.

Occurrence and antimicrobial resistance patterns of Listeria monocytogenes isolated from vegetables

Directory of Open Access Journals (Sweden)

Vanessa de Vasconcelos Byrne

2016-06-01

Full Text Available Abstract Although the consumption of fresh and minimally processed vegetables is considered healthy, outbreaks related to the contamination of these products are frequently reported. Among the food-borne pathogens that contaminate vegetables is Listeria monocytogenes, a ubiquitous organism that exhibits the ability to survive and multiply at refrigerated temperatures. This study aimed to evaluate the occurrence of L. monocytogenes in vegetables as well as the antimicrobial resistance of isolates. The results showed that 3.03% of samples were contaminated with L. monocytogenes, comprising 2.22% of raw vegetables and 5.56% of ready-to-eat vegetables. Multiplex PCR confirmed the virulence potential of the isolates. Antimicrobial resistance profiling showed that 50% of the isolates were susceptible to the antibiotics used. The resistance of one isolate to penicillin G, a commonly employed therapeutic agent, and the presence of serotype 4b, a serotype commonly associated with food-borne outbreaks, could be potential health hazards for consumers.

Pre-banking microbial contamination of donor conjunctiva and storage medium for penetrating keratoplasty.

Science.gov (United States)

Inomata, Takenori; Ono, Koichi; Matsuba, Tsuyoshi; Shiang, Tina; Di Zazzo, Antonio; Nakatani, Satoru; Yamaguchi, Masahiro; Ebihara, Nobuyuki; Murakami, Akira

2017-09-01

The aims of this study were to investigate the incidence of positive donor tissue cultures before transfer to preservation medium (Optisol™-GS) for penetrating keratoplasty, to verify the efficacy of antibiotics contained in Optisol™-GS by examining the drug susceptibility and to assess the relationship between the results of our microbial assessments as well as donor factors and the incidence of contamination. We conducted a retrospective, cross-sectional study using Juntendo Eye Bank records for all corneal transplantations. Two hundred donor conjunctiva harvestings and storage medium (EP-II ® ) cultures were performed between July 2008 and June 2011. We analyzed the associations between donor factors (age, gender, history of cataract surgery, death-to-preservation interval, cause of death) and contamination rates using multivariate analysis by the generalized estimating equation model. We obtained positive bacterial cultures from 154 of the 200 eyes (77.0%). The isolated bacteria were indigenous, such as coagulase-negative Staphylococci, Corynebacterium sp., and methicillin-resistant Staphylococcus aureus (MRSA). There was significant resistance to levofloxacin (18 eyes, 9.0%) and gentamicin (12 eyes, 6.0%), and no vancomycin-resistant bacteria were detected. The donor factors did not correlate with the prevalence of bacterial contamination in our criteria. Pre-banking microbial assessment allows for microbial detection, bacterial susceptibility and resistance testing. This is useful for developing preservation mediums containing effective spectrum antibiotic agents for high quality control of corneal banking.

Gamma-Ray Dosimetry System Using Radiation-Resistant Optical Fibers and a Luminescent Material

International Nuclear Information System (INIS)

Toh, K.; Nakamura, T.; Yamagishi, H.; Sakasai, K.; Soyama, K.; Shikama, T.; Nagata, S.

2013-06-01

Gamma-ray dosimetry system using radiation-resistant optical fibers and a luminescent material was developed for use in a damaged Fukushima Dai-ichi nuclear power plant. The system was designed to be compact and unnecessary of an external supply of electricity to a radiation sensor head with a contaminated working environment and restricted through-holes to a measurement point in the damaged reactor. The system can detect a gamma-ray dose rate at a measurement point using a couple of optical fibers and a luminescent material with a coincidence method. This system demonstrated a linear response with respect to the gamma-ray dose rate from 0.5 mGy/h to 0.1 Gy/h and the system had a capability to measure the dose rate of more than 10 2 Gy/h. (authors)

Two draft genome sequences of Pseudomonas jessenii strains isolated from a copper contaminated site in Denmark

DEFF Research Database (Denmark)

Qin, Yanan; Wang, Dan; Brandt, Kristian Koefoed

2016-01-01

Pseudomonas jessenii C2 and Pseudomonas jessenii H16 were isolated from low-Cu and high-Cu industrially contaminated soil, respectively. P. jessenii H16 displayed significant resistance to copper when compared to P. jessenii C2. Here we describe genome sequences and interesting features of these ......Pseudomonas jessenii C2 and Pseudomonas jessenii H16 were isolated from low-Cu and high-Cu industrially contaminated soil, respectively. P. jessenii H16 displayed significant resistance to copper when compared to P. jessenii C2. Here we describe genome sequences and interesting features...... of these two strains. The genome of P. jessenii C2 comprised 6,420,113 bp, with 5814 protein-coding genes and 67 RNA genes. P. jessenii H16 comprised 6,807,788 bp, with 5995 protein-coding genes and 70 RNA genes. Of special interest was a specific adaptation to this harsh copper-contaminated environment as P....... jessenii H16 contained a novel putative copper resistance genomic island (GI) of around 50,000 bp....

The resistivity imaging application in groundwater exploration: resistivity value and soil type

International Nuclear Information System (INIS)

Mohd Khardzir Husain

2006-01-01

Malaysia is rich in water resources. Water development has fueled socio-economic development of the country during the past decades. Dams and thousands of kilometers of pipes and canals divert water from the rivers to sustain domestic, industrial and agricultural needs. Lately, the water situation for the country has changed from one of relative abundance to one of relative scarcity. The population growth and the expansion in urbanization, industrialization and irrigated agriculture are imposing rapidly growing demands and pressure on the water resources, besides contributing to the rising water pollution. Surface water resource, the traditional source of water supply in the past, has become inadequate in some areas. The problem becomes more acute in areas where surface water is affected by the increasing pollution from industrial and agricultural waste and where changes in land have adversely affected the quantity and quality of surface water supply. The development of groundwater as a source of water supply or as an alternative source is therefore a timely outlook. Lack in groundwater development will becoming disasters to country. Electrical resistivity had been used in groundwater exploration to get an accuracy result in a short time. This method measures the apparent resistivity of the subsurface, including effects of any or all of the following: soil type, bedrock fractures, contaminants and ground water. Variations in electrical resistivity may indicate changes in composition, layer thickness or contaminant levels. The resistivity values obtained from various groundwater exploration and experimental sites shows that the value differs also in related to the soil type. (Author)

High level bacterial contamination of secondary school students' mobile phones.

Science.gov (United States)

Kõljalg, Siiri; Mändar, Rando; Sõber, Tiina; Rööp, Tiiu; Mändar, Reet

2017-06-01

While contamination of mobile phones in the hospital has been found to be common in several studies, little information about bacterial abundance on phones used in the community is available. Our aim was to quantitatively determine the bacterial contamination of secondary school students' mobile phones. Altogether 27 mobile phones were studied. The contact plate method and microbial identification using MALDI-TOF mass spectrometer were used for culture studies. Quantitative PCR reaction for detection of universal 16S rRNA, Enterococcus faecalis 16S rRNA and Escherichia coli allantoin permease were performed, and the presence of tetracycline ( tet A, tet B, tet M), erythromycin ( erm B) and sulphonamide ( sul 1) resistance genes was assessed. We found a high median bacterial count on secondary school students' mobile phones (10.5 CFU/cm 2 ) and a median of 17,032 bacterial 16S rRNA gene copies per phone. Potentially pathogenic microbes ( Staphylococcus aureus , Acinetobacter spp. , Pseudomonas spp., Bacillus cereus and Neisseria flavescens ) were found among dominant microbes more often on phones with higher percentage of E. faecalis in total bacterial 16S rRNA. No differences in contamination level or dominating bacterial species between phone owner's gender and between phone types (touch screen/keypad) were found. No antibiotic resistance genes were detected on mobile phone surfaces. Quantitative study methods revealed high level bacterial contamination of secondary school students' mobile phones.

Effect of long-term zinc pollution on soil microbial community resistance to repeated contamination.

Science.gov (United States)

Klimek, Beata

2012-04-01

The aim of the study was to compare the effects of stress (contamination trials) on the microorganisms in zinc-polluted soil (5,018 mg Zn kg(-1) soil dry weight) and unpolluted soil (141 mg Zn kg(-1) soil dw), measured as soil respiration rate. In the laboratory, soils were subjected to copper contamination (0, 500, 1,500 and 4,500 mg kg(-1) soil dw), and then a bactericide (oxytetracycline) combined with a fungicide (captan) along with glucose (10 mg g(-1) soil dw each) were added. There was a highly significant effect of soil type, copper treatment and oxytetracycline/captan treatment. The initial respiration rate of chronically zinc-polluted soil was higher than that of unpolluted soil, but in the copper treatment it showed a greater decline. Microorganisms in copper-treated soil were more susceptible to oxytetracycline/captan contamination. After the successive soil contamination trials the decline of soil respiration was greater in zinc-polluted soil than in unpolluted soil.

Prevalence and risk factors for methicillin resistant Staphylococcus ...

African Journals Online (AJOL)

Prevalence and risk factors for methicillin resistant Staphylococcus aureus carriage among emergency department workers and bacterial contamination on touch surfaces in Erciyes University Hospital, Kayseri, Turkey.

A comparison of phytoremediation capability of selected plant species for given trace elements

International Nuclear Information System (INIS)

Fischerova, Zuzana; Tlustos, Pavel; Jirina Szakova; Kornelie Sichorova

2006-01-01

In our experiment, As, Cd, Pb, and Zn remediation possibilities on medium contaminated soil were investigated. Seven plant species with a different trace element accumulation capacity and remediation potential were compared. We found good accumulation capabilities and remediation effectiveness of Salix dasyclados similar to studied hyperaccumulators (Arabidopsis halleri and Thlaspi caerulescens). We have noticed better remediation capability in willow compared to poplar for most of the elements considered in this experiment. On the contrary, poplar species were able to remove a larger portion of Pb as opposed to other species. Nevertheless, the removed volume was very small. The elements found in plant biomass depend substantially on the availability of these elements in the soil. Different element concentrations were determined in natural soil solution and by inorganic salt solution extraction (0.01 mol L -1 CaCl 2 ). Extracted content almost exceeded the element concentration in the soil solution. Element concentrations in soil solution were not significantly affected by sampling time. - Selected accumulator trees grown on medium contaminated soil may have remediation capacity similar to hyperaccumulator species

Field ecology, fungal sex and food contamination involving Aspergillus species

Science.gov (United States)

Several species within the genus Aspergillus are capable of producing a myriad of toxic secondary metabolites, with aflatoxin being of most concern. These fungi happen to colonize important agricultural commodities, thereby having the potential to contaminate our food with carcinogenic aflatoxins. P...

Assessment of trace metal contamination of soils around Oluyole ...

African Journals Online (AJOL)

This study was carried out to determine the level of metals contamination of the soils around Oluyole industrial estate in Ibadan. Oluyole industrial estate has heavy concentration of manufacturing industries that generate a lot of waste products capable of introducing metals into the environment. Consequently, twenty-one ...

Remote Robotic Cleaning System for Contaminated Hot-Cell Floor

International Nuclear Information System (INIS)

Kim, Ki Ho; Park, Jang Jin; Yang, Myung S.; Kwon, Hyo Kjo

2005-01-01

The M6 hot-cell of the Irradiated Material Examination Facility at the Korea Atomic Energy Research Institute (KAERI) has been contaminated with spent fuel debris and other radioactive waste due to the DUPIC nuclear fuel development processes. As the hot-cell is active, direct human workers' access, even with protection, to the in-cell is not possible because of the nature of the high radiation level of the spent PWR fuel. A remote robotic cleaning system has been developed for use in a highly radioactive environment of the M6 hot-cell. The remote robotic cleaning system was designed to completely eliminate human interaction with hazardous radioactive contaminants. This robotic cleaning system was also designed to remove contaminants or contaminated smears placed or fixed on the floor of the M6 hot-cell by mopping it in a remote manner. The environmental, functional and mechanical design considerations, control system and capabilities of the developed remote robotic cleaning system are presented

Contaminated fluid filtration plant using pneumatically renewable granulated material

International Nuclear Information System (INIS)

Lucas, J.-C.; Messirejean, Pierre.

1980-01-01

This invention concerns a plant for the filtration of a contaminated fluid flow using a granulated material capable of absorbing or adsorbing the contaminants. This plant includes a filtration box within which there is at least one appreciably vertical filtering bed filled with the material and crossed by the fluid flow, loading and discharge compartments respectively located at the top and bottom of the box, each in communication with the filtering bed and an air-actuated transfer system for loading and discharging this bed through these compartments. Facilities of this kind are used mainly in the nuclear and chemical engineering industries to rid their waste of radio-iodines, generally constituted by elementary iodine and methyl iodide, or of toxic gases that contaminate them. The granulated material, whose job it is to trap these contaminants by adsorption or absorption, is generally composed of active carbon or zeolites whose utilisation time is limited [fr

Feasibility study of X-ray K-edge analysis of RCRA heavy metal contamination of sludge packaged in drums

International Nuclear Information System (INIS)

Jensen, T.

1999-01-01

A study has been completed to assess the capabilities of X-ray K-edge analysis in the measurement of RCRA metal contamination of sludge packaged in drums. Results were obtained for mercury and lead contamination. It was not possible to measure cadmium contamination using this technique. No false positive signals were observed. In cases where uniformity of the sludge can be assumed, this analysis can provide a quick, accurate measurement of heavy-metal contamination

Alpha contamination assessment for D ampersand D activities: Monitoring pipe interiors

International Nuclear Information System (INIS)

Rawool-Sullivan, M.W.; Conaway, J.G.; MacArthur, D.W.; Vaccarella, J.

1996-02-01

We have developed a prototype instrument capable of assessing alpha-emitting contamination on interior surfaces of ducts, pipes, tanks, and other enclosed volumes without inserting a probe. Air is drawn through the potentially contaminated volume and then through a detection grid, where ions created in the air by alpha particles are collected and the resulting charge measured with a sensitive electrometer. A filter at the intake end of the contaminated volume excludes externally created ions, so only ions generated inside the volume are detected. We have studied the response of this prototype in initial experiments using calibrated alpha sources with various pipe diameters and configurations, air flows, and source locations in the pipes. The results of these experiments indicate that this method can be an effective approach to assessing internal contamination

Catalytic extraction processing of contaminated scrap metal

International Nuclear Information System (INIS)

Griffin, T.P.; Johnston, J.E.

1994-01-01

The contract was conceived to establish the commercial capability of Catalytic Extraction Processing (CEP) to treat contaminated scrap metal in the DOE inventory. In so doing, Molten Metal Technology, Inc. (MMT), pursued the following objectives: demonstration of the recycling of ferrous and non-ferrous metals--to establish that radioactively contaminated scrap metal can be converted to high-grade, ferrous and non-ferrous alloys which can be reused by DOE or reintroduced into commerce; immobilize radionuclides--that CEP will concentrate the radionuclides in a dense vitreous phase, minimize secondary waste generation and stabilize and reduce waste volume; destroy hazardous organics--that CEP will convert hazardous organics to valuable industrial gases, which can be used as feed gases for chemical synthesis or as an energy source; recovery volatile heavy metals--that CEP's off-gas treatment system will capture volatile heavy metals, such as mercury and lead; and establish that CEP is economical for processing contaminated scrap metal in the DOE inventory--that CEP is a more cost-effective and, complete treatment and recycling technology than competing technologies for processing contaminated scrap. The process and its performance are described

Application of column tests and electrical resistivity methods for leachate transport monitoring

Directory of Open Access Journals (Sweden)

Wychowaniak Dorota

2015-09-01

Full Text Available Development of the human civilization leads to the pollution of environment. One of the contamination which are a real threat to soil and groundwater are leachates from landfills. In this paper the solute transport through soil was considered. For this purpose, the laboratory column tests of chlorides tracer and leachates transport on two soil samples have been carried out. Furthermore, the electrical resistivity method was applied as auxiliary tool to follow the movements of solute through the soil column what allowed to compare between the results obtained with column test method and electrical resistivity measurements. Breakthrough curves obtained by conductivity and resistivity methods represents similar trends which leads to the conclusion about the suitability of electrical resistivity methods for contamination transport monitoring in soil-water systems.

Airborne gamma spectrometry - towards integration of European operational capability

International Nuclear Information System (INIS)

Toivonen, H.

2003-01-01

Full text: A nuclear threat can take several forms. The fallout from nuclear weapons or from an accident in a nuclear power reactor may contaminate a large area (>>100,000 km 2 ) whereas the dispersion of single sources, either accidentally or deliberately (dirty bomb), contaminates a much smaller area, perhaps only a few thousand square kilometres or less. Airborne gamma spectrometry (AGS) plays an important role in providing detailed information an the dispersion of radioactive materials. AGS using a fixed-wing or a rotary-wing aircraft is at its best in fallout mapping and in searching for orphan sources. Plume tracking could be a third application but is very complex, and there is a risk of vehicle contamination, which would deteriorate mission capability in the later phases of an accident. Because of obvious advantages, unmanned aerial vehicles could be used to monitor the release rate at the site of an accident and perhaps the plume itself. The aim of the present paper is to discuss ways to utilize existing European airborne monitoring capabilities for multilateral assistance in an accident and to give some thoughts to how an integrated system could be developed to take into account various national measuring strategies. In a large-scale accident, it is to be expected that the European countries use their radiological resources to map their own territory. It is realistic to think of assistance by transferring equipment and staff to another country only in accident scenarios where a country or countries with essential AGS capability would not have been affected by the fallout. Various AGS survey results can be fused only if a common platform for data exchange is available. Formats and protocols have been developed for special cases (ECCOMAGS, Nuclear Fission Safety, 4 th and 5 th Framework Programmes) but there are no universal solutions applicable to different situations and Instruments. The hardware and software among the European AGS teams are tailor

Dietary components in the development of leptin resistance.

Science.gov (United States)

Vasselli, Joseph R; Scarpace, Philip J; Harris, Ruth B S; Banks, William A

2013-03-01

Classically, leptin resistance has been associated with increased body fat and circulating leptin levels, and the condition is believed to contribute to the onset and/or maintenance of obesity. Although a great deal is known about the central nervous system mechanisms mediating leptin resistance, considerably less is known about the role of diet in establishing and maintaining this altered hormonal state. An exciting new finding has recently been published demonstrating the existence of leptin resistance in normal-weight rats with lean leptin levels by feeding them a high-concentration-fructose diet. This finding has opened the possibility that specific macronutrients may be capable of inducing leptin resistance, independently of the amount of body fat or circulating leptin present in the treated animals. This review describes several lines of research that have recently emerged indicating that specific types of dietary sugars and fats are capable of inducing leptin resistance in experimental rodent models. The results further show that diet-induced leptin resistance is capable of increasing energy intake and elevating body weight gain under appropriate dietary challenges. It appears that biological mechanisms on multiple levels may underlie the dietary induction of leptin resistance, including alterations in the leptin blood-to-brain transport system, in peripheral glucose metabolism, and in central leptin receptor signaling pathways. What is clear from the findings reviewed here is that diet-induced leptin resistance can occur in the absence of elevated circulating leptin levels and body weight, rendering it a potential cause and/or predisposing factor to excess body weight gain and obesity.

Rugged Packaging for Damage Resistant Inertial Fusion Energy Optics

Energy Technology Data Exchange (ETDEWEB)

Stelmack, Larry

2003-11-17

The development of practical fusion energy plants based on inertial confinement with ultraviolet laser beams requires durable, stable final optics that will withstand the harsh fusion environment. Aluminum-coated reflective surfaces are fragile, and require hard overcoatings resistant to contamination, with low optical losses at 248.4 nanometers for use with high-power KrF excimer lasers. This program addresses the definition of requirements for IFE optics protective coatings, the conceptual design of the required deposition equipment according to accepted contamination control principles, and the deposition and evaluation of diamondlike carbon (DLC) test coatings. DLC coatings deposited by Plasma Immersion Ion Processing were adherent and abrasion-resistant, but their UV optical losses must be further reduced to allow their use as protective coatings for IFE final optics. Deposition equipment for coating high-performance IFE final optics must be designed, constructed, and operated with contamination control as a high priority.

IN SITU REMEDIATION OF CONTAMINATED SEDIMENTS - ACTIVE CAPPING TECHNOLOGY

Energy Technology Data Exchange (ETDEWEB)

Knox, A.; Roberts, J.; Paller, M.; Reible, D.

2010-09-02

Active capping is a relatively new approach for treating contaminated sediments. It involves applying chemically reactive amendments to the sediment surface. The main role of active caps is to stabilize contaminants in contaminated sediments, lower the bioavailable pool of contaminants, and reduce the release of contaminants to the water column. Metals are common contaminants in many marine and fresh water environments as a result of industrial and military activities. The mobile, soluble forms of metals are generally considered toxic. Induced chemical precipitation of these metals can shift toxic metals from the aqueous phase to a solid, precipitated phase which is often less bioavailable. This approach can be achieved through application of sequestering agents such as rock phosphates, organoclays, zeolites, clay minerals, and biopolymers (e.g., chitosan) in active capping technology. Active capping holds great potential for a more permanent solution that avoids residual risks resulting from contaminant migration through the cap or breaching of the cap. In addition to identifying superior active capping agents, research is needed to optimize application techniques, application rates, and amendment combinations that maximize sequestration of contaminants. A selected set of active capping treatment technologies has been demonstrated at a few sites, including a field demonstration at the Savannah River Site, Aiken, SC. This demonstration has provided useful information on the effects of sequestering agents on metal immobilization, bioavailability, toxicity, and resistance to mechanical disturbance.

In Situ Remediation Of Contaminated Sediments - Active Capping Technology

International Nuclear Information System (INIS)

Knox, A.; Roberts, J.; Paller, M.; Reible, D.

2010-01-01

Active capping is a relatively new approach for treating contaminated sediments. It involves applying chemically reactive amendments to the sediment surface. The main role of active caps is to stabilize contaminants in contaminated sediments, lower the bioavailable pool of contaminants, and reduce the release of contaminants to the water column. Metals are common contaminants in many marine and fresh water environments as a result of industrial and military activities. The mobile, soluble forms of metals are generally considered toxic. Induced chemical precipitation of these metals can shift toxic metals from the aqueous phase to a solid, precipitated phase which is often less bioavailable. This approach can be achieved through application of sequestering agents such as rock phosphates, organoclays, zeolites, clay minerals, and biopolymers (e.g., chitosan) in active capping technology. Active capping holds great potential for a more permanent solution that avoids residual risks resulting from contaminant migration through the cap or breaching of the cap. In addition to identifying superior active capping agents, research is needed to optimize application techniques, application rates, and amendment combinations that maximize sequestration of contaminants. A selected set of active capping treatment technologies has been demonstrated at a few sites, including a field demonstration at the Savannah River Site, Aiken, SC. This demonstration has provided useful information on the effects of sequestering agents on metal immobilization, bioavailability, toxicity, and resistance to mechanical disturbance.

Portable instrumentation for quantitatively measuring radioactive surface contaminations, including 90Sr

International Nuclear Information System (INIS)

Brodzinski, R.L.

1983-10-01

In order to measure the effectiveness of decontamination efforts, a quantitative analysis of the radiocontamination is necessary, both before and after decontamination. Since it is desirable to release the decontaminated material for unrestricted use or disposal, the assay equipment must provide adequate sensitivity to measure the radioactivity at or below the release limit. In addition, the instrumentation must be capable of measuring all kinds of radiocontaminants including fission products, activation products, and transuranic materials. Finally, the survey instrumentation must be extremely versatile in order to assay the wide variety of contaminated surfaces in many environments, some of which may be extremely hostile or remote. This communication describes the development and application of portable instrumentation capable of quantitatively measuring most transuranics, activation products, and fission products, including 90 Sr, on almost any contaminated surface in nearly any location

Characterization of radioactive contamination inside pipes with the Pipe Explorer trademark system

International Nuclear Information System (INIS)

Kendrick, D.T.; Cremer, C.D.; Lowry, W.; Cramer, E.

1995-01-01

The U.S. Department of Energy's nuclear facility decommissioning program needs to characterize radiological contamination inside piping systems before the pipe can be recycled, remediated, or disposed. Science and Engineering associates, Inc. under contract with the DOE Morgantown Energy Technology Center has developed and demonstrated the Pipe Explorer trademark system, which uses an inverting membrane to transport various characterization sensors into pipes. The basic process involves inverting (turning inside out) a tubular impermeable membrane under air pressure. A characterization sensor is towed down the interior of the pipe by the membrane. Advantages of this approach include the capability of deploying through constrictions in the pipe, around 90 degrees bends, vertically up and down, and in slippery conditions. Because the detector is transported inside the membrane (which is inexpensive and disposable), it is protected from contamination, which eliminates cross-contamination. Characterization sensors that have been demonstrated with the system thus far include: gamma detectors, beta detectors, video cameras, and pipe locators. Alpha measurement capability is currently under development. A remotely operable Pipe Explorer trademark system has been developed and demonstrated for use in DOE facilities in the decommissioning stage. The system is capable of deployment in pipes as small as 2-inch-diameter and up to 250 feet long. This paper describes the technology and presents measurement results of a field demonstration conducted with the Pipe Explorer trademark system at a DOE site. These measurements identify surface activity levels of U-238 contamination as a function of location in drain lines. Cost savings to the DOE of approximately $1.5 million dollars were realized from this one demonstration

Roles of inter-SWCNT junctions in resistive humidity response

International Nuclear Information System (INIS)

Zhang, Kang; Zou, Jianping; Zhang, Qing

2015-01-01

As a promising chemiresistor for gas sensing, the single-walled carbon nanotube (SWCNT) network has not yet been fully utilized for humidity detection. In this work, it is found that as humidity increases from 10% to 85%, the resistance of as-grown SWCNT networks first decreases and then increases. This non-monotonic resistive response to humidity limits their sensing capabilities. The competition between SWCNT resistance and inter-tube junction resistance changes is then found to be responsible for the non-monotonic resistive humidity responses. Moreover, creating sp"3 scattering centers on the SWCNT sidewall by monovalent functionalization of four-bromobenzene diazonium tetrafluoroborate is shown to be capable of eliminating the influence from the inter-tube junctions, resulting in a continuous resistance drop as humidity increases from 10% to 85%. Our results revealed the competing resistive humidity sensing process in as-grown SWCNT networks, which could also be helpful in designing and optimizing as-grown SWCNT networks for humidity sensors and other gas sensors. (paper)

OCCURRENCE OF MICROORGANISMS RESISTANT TO MERCURY IN MERCURY CONTAMINATED SOILS AND SEDIMENTS IN PAVLODAR, KAZAKHSTAN

Science.gov (United States)

There is extensive mercury contamination of soil surrounding a chloralkali plant in Pavlodar, Kazakhstan that operated from 1970 to 1990. High-level mercury contamination exists within the confines of the plant, at nearby off-site waste storage and evaporation ponds, and in Balky...

High-resolution Electrical Resistivity Tomography monitoring of a tracer test in a confined aquifer

Science.gov (United States)

Wilkinson, P. B.; Meldrum, P. I.; Kuras, O.; Chambers, J. E.; Holyoake, S. J.; Ogilvy, R. D.

2010-04-01

A permanent geoelectrical subsurface imaging system has been installed at a contaminated land site to monitor changes in groundwater quality after the completion of a remediation programme. Since the resistivities of earth materials are sensitive to the presence of contaminants and their break-down products, 4-dimensional resistivity imaging can act as a surrogate monitoring technology for tracking and visualising changes in contaminant concentrations at much higher spatial and temporal resolution than manual intrusive investigations. The test site, a municipal car park built on a former gasworks, had been polluted by a range of polycyclic aromatic hydrocarbons and dissolved phase contaminants. It was designated statutory contaminated land under Part IIA of the UK Environmental Protection Act due to the risk of polluting an underlying minor aquifer. Resistivity monitoring zones were established on the boundaries of the site by installing vertical electrode arrays in purpose-drilled boreholes. After a year of monitoring data had been collected, a tracer test was performed to investigate groundwater flow velocity and to demonstrate rapid volumetric monitoring of natural attenuation processes. A saline tracer was injected into the confined aquifer, and its motion and evolution were visualised directly in high-resolution tomographic images in near real-time. Breakthrough curves were calculated from independent resistivity measurements, and the estimated seepage velocities from the monitoring images and the breakthrough curves were found to be in good agreement with each other and with estimates based on the piezometric gradient and assumed material parameters.

Advanced Simulation Capability for Environmental Management: Development and Demonstrations - 12532

Energy Technology Data Exchange (ETDEWEB)

Freshley, Mark D.; Freedman, Vicky; Gorton, Ian [Pacific Northwest National Laboratory, MSIN K9-33, P.O. Box 999, Richland, WA 99352 (United States); Hubbard, Susan S. [Lawrence Berkeley National Laboratory, 1 Cyclotron Road, MS 50B-4230, Berkeley, CA 94720 (United States); Moulton, J. David; Dixon, Paul [Los Alamos National Laboratory, MS B284, P.O. Box 1663, Los Alamos, NM 87544 (United States)

2012-07-01

The U.S. Department of Energy Office of Environmental Management (EM), Technology Innovation and Development is supporting development of the Advanced Simulation Capability for Environmental Management (ASCEM). ASCEM is a state-of-the-art scientific tool and approach for understanding and predicting contaminant fate and transport in natural and engineered systems. The modular and open source high-performance computing tool facilitates integrated approaches to modeling and site characterization that enable robust and standardized assessments of performance and risk for EM cleanup and closure activities. The ASCEM project continues to make significant progress in development of capabilities, which are organized into Platform and Integrated Tool-sets and a High-Performance Computing Multi-process Simulator. The Platform capabilities target a level of functionality to allow end-to-end model development, starting with definition of the conceptual model and management of data for model input. The High-Performance Computing capabilities target increased functionality of process model representations, tool-sets for interaction with Platform, and verification and model confidence testing. The new capabilities are demonstrated through working groups, including one focused on the Hanford Site Deep Vadose Zone. The ASCEM program focused on planning during the first year and executing a prototype tool-set for an early demonstration of individual components. Subsequently, ASCEM has focused on developing and demonstrating an integrated set of capabilities, making progress toward a version of the capabilities that can be used to engage end users. Demonstration of capabilities continues to be implemented through working groups. Three different working groups, one focused on EM problems in the deep vadose zone, another investigating attenuation mechanisms for metals and radionuclides, and a third focusing on waste tank performance assessment, continue to make progress. The project

Satellite Contamination and Materials Outgassing Knowledge base

Science.gov (United States)

Minor, Jody L.; Kauffman, William J. (Technical Monitor)

2001-01-01

Satellite contamination continues to be a design problem that engineers must take into account when developing new satellites. To help with this issue, NASA's Space Environments and Effects (SEE) Program funded the development of the Satellite Contamination and Materials Outgassing Knowledge base. This engineering tool brings together in one location information about the outgassing properties of aerospace materials based upon ground-testing data, the effects of outgassing that has been observed during flight and measurements of the contamination environment by on-orbit instruments. The knowledge base contains information using the ASTM Standard E- 1559 and also consolidates data from missions using quartz-crystal microbalances (QCM's). The data contained in the knowledge base was shared with NASA by government agencies and industry in the US and international space agencies as well. The term 'knowledgebase' was used because so much information and capability was brought together in one comprehensive engineering design tool. It is the SEE Program's intent to continually add additional material contamination data as it becomes available - creating a dynamic tool whose value to the user is ever increasing. The SEE Program firmly believes that NASA, and ultimately the entire contamination user community, will greatly benefit from this new engineering tool and highly encourages the community to not only use the tool but add data to it as well.

Occurrence and antimicrobial resistance patterns of Listeria monocytogenes isolated from vegetables.

Science.gov (United States)

de Vasconcelos Byrne, Vanessa; Hofer, Ernesto; Vallim, Deyse Christina; de Castro Almeida, Rogeria Comastri

2016-01-01

Although the consumption of fresh and minimally processed vegetables is considered healthy, outbreaks related to the contamination of these products are frequently reported. Among the food-borne pathogens that contaminate vegetables is Listeria monocytogenes, a ubiquitous organism that exhibits the ability to survive and multiply at refrigerated temperatures. This study aimed to evaluate the occurrence of L. monocytogenes in vegetables as well as the antimicrobial resistance of isolates. The results showed that 3.03% of samples were contaminated with L. monocytogenes, comprising 2.22% of raw vegetables and 5.56% of ready-to-eat vegetables. Multiplex PCR confirmed the virulence potential of the isolates. Antimicrobial resistance profiling showed that 50% of the isolates were susceptible to the antibiotics used. The resistance of one isolate to penicillin G, a commonly employed therapeutic agent, and the presence of serotype 4b, a serotype commonly associated with food-borne outbreaks, could be potential health hazards for consumers. Copyright © 2016 Sociedade Brasileira de Microbiologia. Published by Elsevier Editora Ltda. All rights reserved.

Distribution of quinolones, sulfonamides, tetracyclines in aquatic environment and antibiotic resistance in Indochina

Directory of Open Access Journals (Sweden)

Satoru eSuzuki

2012-02-01

Full Text Available Southeast Asia has become the center of rapid industrial development and economic growth. However, this growth has far outpaced investment in public infrastructure, leading to the unregulated release of many pollutants, including wastewater-related contaminants such as antibiotics. Antibiotics are of major concern because they can easily be released into the environment from numerous sources, and can subsequently induce development of antibiotic-resistant bacteria. Recent studies have shown that for some categories of drugs this source-to-environment antibiotic resistance relationship is more complex. This review summarizes current understanding regarding the presence of quinolones, sulfonamides, and tetracyclines in aquatic environments of Indochina and the prevalence of bacteria resistant to them. Several noteworthy findings are discussed: 1 quinolone contamination and the occurrence of quinolone resistance are not correlated; 2 occurrence of the sul sulfonamide resistance gene varies geographically; and 3 microbial diversity might be related to the rate of oxytetracycline resistance.

Muddying the Waters: A New Area of Concern for Drinking Water Contamination in Cameroon

Directory of Open Access Journals (Sweden)

Jessica M. Healy Profitós

2014-11-01

Full Text Available In urban Maroua, Cameroon, improved drinking water sources are available to a large majority of the population, yet this water is frequently distributed through informal distribution systems and stored in home containers (canaries, leaving it vulnerable to contamination. We assessed where contamination occurs within the distribution system, determined potential sources of environmental contamination, and investigated potential pathogens. Gastrointestinal health status (785 individuals was collected via health surveys. Drinking water samples were collected from drinking water sources and canaries. Escherichia coli and total coliform levels were evaluated and molecular detection was performed to measure human-associated faecal marker, HF183; tetracycline-resistance gene, tetQ; Campylobacter spp.; and Staphylococcus aureus. Statistical analyses were performed to evaluate the relationship between microbial contamination and gastrointestinal illness. Canari samples had higher levels of contamination than source samples. HF183 and tetQ were detected in home and source samples. An inverse relationship was found between tetQ and E. coli. Presence of tetQ with lower E. coli levels increased the odds of reported diarrhoeal illness than E. coli levels alone. Further work is warranted to better assess the relationship between antimicrobial-resistant bacteria and other pathogens in micro-ecosystems within canaries and this relationship’s impact on drinking water quality.

Drinking water from dug wells in rural ghana--salmonella contamination, environmental factors, and genotypes.

Science.gov (United States)

Dekker, Denise Myriam; Krumkamp, Ralf; Sarpong, Nimako; Frickmann, Hagen; Boahen, Kennedy Gyau; Frimpong, Michael; Asare, Renate; Larbi, Richard; Hagen, Ralf Matthias; Poppert, Sven; Rabsch, Wolfgang; Marks, Florian; Adu-Sarkodie, Yaw; May, Jürgen

2015-03-27

Salmonellosis is an important but neglected disease in sub-Saharan Africa. Food or fecal-oral associated transmissions are the primary cause of infections, while the role of waterborne transmission is unclear. Samples were collected from different dug wells in a rural area of Ghana and analyzed for contamination with bacteria, and with Salmonella in particular. In addition, temporal dynamics and riks factors for contamination were investigated in 16 wells. For all Salmonella isolates antibiotic susceptibility testing was performed, serovars were determined and strains from the same well with the same serovar were genotyped. The frequency of well water contamination with Gram-negative rod-shaped bacteria was 99.2% (n = 395). Out of 398 samples, 26 (6.5%) tested positive for Salmonella spp. The serovar distribution was diverse including strains not commonly isolated from clinical samples. Resistance to locally applied antibiotics or resistance to fluoroquinolones was not seen in the Salmonella isolates. The risk of Salmonella contamination was lower in wells surrounded by a frame and higher during the rainy season. The study confirms the overall poor microbiological quality of well water in a resource-poor area of Ghana. Well contamination with Salmonella poses a potential threat of infection, thus highlighting the important role of drinking water safety in infectious disease control.

Muddying the Waters: A New Area of Concern for Drinking Water Contamination in Cameroon

Science.gov (United States)

Healy Profitós, Jessica M.; Mouhaman, Arabi; Lee, Seungjun; Garabed, Rebecca; Moritz, Mark; Piperata, Barbara; Tien, Joe; Bisesi, Michael; Lee, Jiyoung

2014-01-01

In urban Maroua, Cameroon, improved drinking water sources are available to a large majority of the population, yet this water is frequently distributed through informal distribution systems and stored in home containers (canaries), leaving it vulnerable to contamination. We assessed where contamination occurs within the distribution system, determined potential sources of environmental contamination, and investigated potential pathogens. Gastrointestinal health status (785 individuals) was collected via health surveys. Drinking water samples were collected from drinking water sources and canaries. Escherichia coli and total coliform levels were evaluated and molecular detection was performed to measure human-associated faecal marker, HF183; tetracycline-resistance gene, tetQ; Campylobacter spp.; and Staphylococcus aureus. Statistical analyses were performed to evaluate the relationship between microbial contamination and gastrointestinal illness. Canari samples had higher levels of contamination than source samples. HF183 and tetQ were detected in home and source samples. An inverse relationship was found between tetQ and E. coli. Presence of tetQ with lower E. coli levels increased the odds of reported diarrhoeal illness than E. coli levels alone. Further work is warranted to better assess the relationship between antimicrobial-resistant bacteria and other pathogens in micro-ecosystems within canaries and this relationship’s impact on drinking water quality. PMID:25464137

INFLUENCE OF THE CONTAMINATION OF BLOOD MIXED WITH SALIVA ON ADHESIVE SHEAR RESISTANCE AND THE INDICE OF ADHESIVE REMAINING THE TWO NEW COMPOSITES

Directory of Open Access Journals (Sweden)

Matheus Melo Pithon

2007-03-01

Full Text Available The objective of this study was to evaluate shear resistance and the índice of adhesive remaining (IAR the composite Eagle bond and Orthobond after contamination of enamel by blood mixed with saliva. Sixty bovine permanent lower incisors were divided into four groups (n = 15. In Group 1 and Group 3 the bonding procedures were performed by using Eagle Bond and Orthobond composites, respectively, according to the manufacturer’s recommendations. In Group 2 and Group 4 the bonding procedures were performed by using Eagle Bond and Orthobond composites, respectively, according to the manufacturer’s recommendations, before the bonding in which the conditioned enamel was contaminated by blood mixed with saliva, followed by washing with a jet of air and water, drying, and gluing of the accessory. After bonding the brackets, all the samples were submitted to shear bond strength tests by means of an Emic universal testing machine at a crosshead speed of 0.5 mm/min. The results (MPa showed no statistically significant differences between the groups (P > 0.05. A greater number of fractures in the bracket/composite interface were evidenced by the ARI (Adhesive Remnant Index scores the groups 3 and 4.

Influence of the contamination of blood mixed with saliva on adhesive shear resistance and the indice of adhesive remaining the two new composites

Directory of Open Access Journals (Sweden)

Matheus Melo Pithon

2007-01-01

Full Text Available The objective of this study was to evaluate shear resistance and the índice of adhesive remaining (IAR the composite Eagle bond and Orthobond after contamination of enamel by blood mixed with saliva. Sixty bovine permanent lower incisors were divided into four groups (n = 15. In Group 1 and Group 3 the bonding procedures were performed by using Eagle Bond and Orthobond composites, respectively, according to the manufacturer’s recommendations. In Group 2 and Group 4 the bonding procedures were performed by using Eagle Bond and Orthobond composites, respectively, according to the manufacturer’s recommendations, before the bonding in which the conditioned enamel was contaminated by blood mixed with saliva, followed by washing with a jet of air and water, drying, and gluing of the accessory. After bonding the brackets, all the samples were submitted to shear bond strength tests by means of an Emic universal testing machine at a crosshead speed of 0.5 mm/min. The results (MPa showed no statistically significant differences between the groups (P > 0.05. A greater number of fractures in the bracket/composite interface were evidenced by the ARI (Adhesive Remnant Index scores the groups 3 and 4.

Adaptation of microalgae to a gradient of continuous petroleum contamination

Energy Technology Data Exchange (ETDEWEB)

Carrera-Martinez, Daniel; Mateos-Sanz, Aranzazu [AlgasGen Biotecnologia, EBT-UCM, Facultad de Veterinaria, Universidad Complutense de Madrid, Puerta de Hierro s/n, E-28040 Madrid (Spain); Lopez-Rodas, Victoria [AlgasGen Biotecnologia, EBT-UCM, Facultad de Veterinaria, Universidad Complutense de Madrid, Puerta de Hierro s/n, E-28040 Madrid (Spain); Genetica, Facultad de Veterinaria, Universidad Complutense de Madrid, Puerta de Hierro s/n, E-28040 Madrid (Spain); Costas, Eduardo, E-mail: ecostas@vet.ucm.es [AlgasGen Biotecnologia, EBT-UCM, Facultad de Veterinaria, Universidad Complutense de Madrid, Puerta de Hierro s/n, E-28040 Madrid (Spain); Genetica, Facultad de Veterinaria, Universidad Complutense de Madrid, Puerta de Hierro s/n, E-28040 Madrid (Spain)

2011-01-25

In order to study adaptation of microalgae to petroleum contamination, we have examined an environmental stress gradient by crude oil contamination in the Arroyo Minero River (AMR), Argentina. Underground crude oil has constantly leaked out since 1915 as a consequence of test drilling for possible petroleum exploitation. Numerous microalgae species proliferated in AMR upstream of the crude oil spill. In contrast, only four microalgal species were detected in the crude oil spill area. Species richness increases again downstream. Microalgae biomass in the crude oil spill area is dominated by a mesophile species, Scenedesmus sp. Effects of oil samples from AMR spill on photosynthetic performance and growth were studied using laboratory cultures of two Scenedesmus sp. strains. One strain (Se-co) was isolated from the crude oil spill area. The other strain (Se-pr) was isolated from a pristine area without petroleum contamination. Crude oil has undetectable effects on Se-co strain. In contrast crude oil rapidly destroys Se-pr strain. However, Se-pr strain can adapt to low doses of petroleum ({<=}3% v/v total hydrocarbons/water) by means of physiological acclimatization. In contrast, only rare crude oil-resistant mutants are able to grow under high levels of crude oil ({>=}10% v/v total hydrocarbons/water). These crude oil-resistant mutants have arisen through rare spontaneous mutations that occur prior to crude oil exposure. Species richness in different areas of AMR is closely connected to the kind of mechanism (genetic adaptation vs. physiological acclimatization) that allows adaptation. Resistant-mutants are enough to assure the survival of microalgal species under catastrophic crude oil spill.

RNA Sequencing of Contaminated Seeds Reveals the State of the Seed Permissive for Pre-Harvest Aflatoxin Contamination and Points to a Potential Susceptibility Factor

Directory of Open Access Journals (Sweden)

Josh Clevenger

2016-11-01

Full Text Available Pre-harvest aflatoxin contamination (PAC is a major problem facing peanut production worldwide. Produced by the ubiquitous soil fungus, Aspergillus flavus, aflatoxin is the most naturally occurring known carcinogen. The interaction between fungus and host resulting in PAC is complex, and breeding for PAC resistance has been slow. It has been shown that aflatoxin production can be induced by applying drought stress as peanut seeds mature. We have implemented an automated rainout shelter that controls temperature and moisture in the root and peg zone to induce aflatoxin production. Using polymerase chain reaction (PCR and high performance liquid chromatography (HPLC, seeds meeting the following conditions were selected: infected with Aspergillus flavus and contaminated with aflatoxin; and not contaminated with aflatoxin. RNA sequencing analysis revealed groups of genes that describe the transcriptional state of contaminated vs. uncontaminated seed. These data suggest that fatty acid biosynthesis and abscisic acid (ABA signaling are altered in contaminated seeds and point to a potential susceptibility factor, ABR1, as a repressor of ABA signaling that may play a role in permitting PAC.

RNA Sequencing of Contaminated Seeds Reveals the State of the Seed Permissive for Pre-Harvest Aflatoxin Contamination and Points to a Potential Susceptibility Factor

Science.gov (United States)

Clevenger, Josh; Marasigan, Kathleen; Liakos, Vasileios; Sobolev, Victor; Vellidis, George; Holbrook, Corley; Ozias-Akins, Peggy

2016-01-01

Pre-harvest aflatoxin contamination (PAC) is a major problem facing peanut production worldwide. Produced by the ubiquitous soil fungus, Aspergillus flavus, aflatoxin is the most naturally occurring known carcinogen. The interaction between fungus and host resulting in PAC is complex, and breeding for PAC resistance has been slow. It has been shown that aflatoxin production can be induced by applying drought stress as peanut seeds mature. We have implemented an automated rainout shelter that controls temperature and moisture in the root and peg zone to induce aflatoxin production. Using polymerase chain reaction (PCR) and high performance liquid chromatography (HPLC), seeds meeting the following conditions were selected: infected with Aspergillus flavus and contaminated with aflatoxin; and not contaminated with aflatoxin. RNA sequencing analysis revealed groups of genes that describe the transcriptional state of contaminated vs. uncontaminated seed. These data suggest that fatty acid biosynthesis and abscisic acid (ABA) signaling are altered in contaminated seeds and point to a potential susceptibility factor, ABR1, as a repressor of ABA signaling that may play a role in permitting PAC. PMID:27827875

The stability evaluation of lime mud as transesterification catalyst in resisting CO2 and H2O for biodiesel production

International Nuclear Information System (INIS)

Li, Hui; Niu, Sheng-li; Lu, Chun-mei; Cheng, Shi-qing

2015-01-01

Highlights: • Lime mud (LM) is pretreated with calcination, hydration and desiccation. • The alkali solubility is the amount of alkali compounds dissolved in methanol. • The soluble alkali amount in LM700-H is higher than that of CaO–H. • LM700 possesses a stronger capability than CaO in resisting H 2 O and CO 2 . - Abstract: The most outstanding property of the heterogeneous transesterification catalysts is recyclable, but their catalytic activity may be depressed for the absorption of moisture (H 2 O) and carbon dioxide (CO 2 ) in air, especially for the basic ones. Lime mud (LM) is effective in catalyzing transesterification, yet its property in resisting H 2 O and CO 2 is indistinct, which should be emphasized. In this study, the LM based transesterification catalyst is prepared through calcinations. Then, it is hydrated and desiccated to simulate the contamination by H 2 O and CO 2 . Further, the fresh and the contaminated catalysts are characterized by X-ray diffraction (XRD), thermogravimetric analysis (TGA), Fourier transform infrared spectroscopy (FTIR), Hammette indicator, Brunauer–Emmett–Teller (BET) surface area and soluble alkali examination, to reveal the mechanism of LM in resisting H 2 O and CO 2 . Meanwhile, the analytical grade calcium oxide (CaO) is chosen for comparison. Finally, to comprehensively investigate the influences of H 2 O and CO 2 on LM in catalyzing transesterification, the factors of the catalyst addition percentage, molar ratio of methanol to oil and transesterification temperature are evaluated

Tuning resistance states by thickness control in an electroforming-free nanometallic complementary resistance random access memory

Science.gov (United States)

Yang, Xiang; Lu, Yang; Lee, Jongho; Chen, I.-Wei

2016-01-01

Tuning low resistance state is crucial for resistance random access memory (RRAM) that aims to achieve optimal read margin and design flexibility. By back-to-back stacking two nanometallic bipolar RRAMs with different thickness into a complementary structure, we have found that its low resistance can be reliably tuned over several orders of magnitude. Such high tunability originates from the exponential thickness dependence of the high resistance state of nanometallic RRAM, in which electron wave localization in a random network gives rise to the unique scaling behavior. The complementary nanometallic RRAM provides electroforming-free, multi-resistance-state, sub-100 ns switching capability with advantageous characteristics for memory arrays.

Tuning resistance states by thickness control in an electroforming-free nanometallic complementary resistance random access memory

International Nuclear Information System (INIS)

Yang, Xiang; Lu, Yang; Lee, Jongho; Chen, I-Wei

2016-01-01

Tuning low resistance state is crucial for resistance random access memory (RRAM) that aims to achieve optimal read margin and design flexibility. By back-to-back stacking two nanometallic bipolar RRAMs with different thickness into a complementary structure, we have found that its low resistance can be reliably tuned over several orders of magnitude. Such high tunability originates from the exponential thickness dependence of the high resistance state of nanometallic RRAM, in which electron wave localization in a random network gives rise to the unique scaling behavior. The complementary nanometallic RRAM provides electroforming-free, multi-resistance-state, sub-100 ns switching capability with advantageous characteristics for memory arrays

Does human activity impact the natural antibiotic resistance background? Abundance of antibiotic resistance genes in 21 Swiss lakes.

Science.gov (United States)

Czekalski, Nadine; Sigdel, Radhika; Birtel, Julia; Matthews, Blake; Bürgmann, Helmut

2015-08-01

Antibiotic resistance genes (ARGs) are emerging environmental contaminants, known to be continuously discharged into the aquatic environment via human and animal waste. Freshwater aquatic environments represent potential reservoirs for ARG and potentially allow sewage-derived ARG to persist and spread in the environment. This may create increased opportunities for an eventual contact with, and gene transfer to, human and animal pathogens via the food chain or drinking water. However, assessment of this risk requires a better understanding of the level and variability of the natural resistance background and the extent of the human impact. We have analyzed water samples from 21 Swiss lakes, taken at sampling points that were not under the direct influence of local contamination sources and analyzed the relative abundance of ARG using quantitative real-time PCR. Copy numbers of genes mediating resistance to three different broad-spectrum antibiotic classes (sulfonamides: sul1, sul2, tetracyclines: tet(B), tet(M), tet(W) and fluoroquinolones: qnrA) were normalized to copy numbers of bacterial 16S rRNA genes. We used multiple linear regression to assess if ARG abundance is related to human activities in the catchment, microbial community composition and the eutrophication status of the lakes. Sul genes were detected in all sampled lakes, whereas only four lakes contained quantifiable numbers of tet genes, and qnrA remained below detection in all lakes. Our data indicate higher abundance of sul1 in lakes with increasing number and capacity of wastewater treatment plants (WWTPs) in the catchment. sul2 abundance was rather related to long water residence times and eutrophication status. Our study demonstrates the potential of freshwater lakes to preserve antibiotic resistance genes, and provides a reference for ARG abundance from lake systems with low human impact as a baseline for assessing ARG contamination in lake water. Copyright © 2015 Elsevier Ltd. All rights

Structural Capability of an Organization toward Innovation Capability

DEFF Research Database (Denmark)

Nielsen, Susanne Balslev; Momeni, Mostafa

2016-01-01

The scholars in the field of strategic management have developed two major approaches for attainment of competitive advantage: an approach based on environmental opportunities, and another one based on internal capabilities of an organization. Some investigations in the last two decades have...... indicated that the advantages relying on the internal capabilities of organizations may determine the competitive position of organizations better than environmental opportunities do. Characteristics of firms shows that one of the most internal capabilities that lead the organizations to the strongest...... competitive advantage in the organizations is the innovation capability. The innovation capability is associated with other organizational capabilities, and many organizations have focused on the need to identify innovation capabilities.This research focuses on recognition of the structural aspect...

Dietary Components in the Development of Leptin Resistance123

Science.gov (United States)

Vasselli, Joseph R.; Scarpace, Philip J.; Harris, Ruth B. S.; Banks, William A.

2013-01-01

Classically, leptin resistance has been associated with increased body fat and circulating leptin levels, and the condition is believed to contribute to the onset and/or maintenance of obesity. Although a great deal is known about the central nervous system mechanisms mediating leptin resistance, considerably less is known about the role of diet in establishing and maintaining this altered hormonal state. An exciting new finding has recently been published demonstrating the existence of leptin resistance in normal-weight rats with lean leptin levels by feeding them a high-concentration-fructose diet. This finding has opened the possibility that specific macronutrients may be capable of inducing leptin resistance, independently of the amount of body fat or circulating leptin present in the treated animals. This review describes several lines of research that have recently emerged indicating that specific types of dietary sugars and fats are capable of inducing leptin resistance in experimental rodent models. The results further show that diet-induced leptin resistance is capable of increasing energy intake and elevating body weight gain under appropriate dietary challenges. It appears that biological mechanisms on multiple levels may underlie the dietary induction of leptin resistance, including alterations in the leptin blood-to-brain transport system, in peripheral glucose metabolism, and in central leptin receptor signaling pathways. What is clear from the findings reviewed here is that diet-induced leptin resistance can occur in the absence of elevated circulating leptin levels and body weight, rendering it a potential cause and/or predisposing factor to excess body weight gain and obesity. PMID:23493533

Metal-resistant rhizobacteria isolates improve Mucuna deeringiana phytoextraction capacity in multi-metal contaminated soils from a gold mining area.

Science.gov (United States)

Boechat, Cácio Luiz; Giovanella, Patricia; Amorim, Magno Batista; de Sá, Enilson Luiz Saccol; de Oliveira Camargo, Flávio Anastácio

2017-01-01

Phytoremediation consists of biological techniques for heavy metal remediation, which include exploring the genetic package of vegetable species to remove heavy metals from the environment. The goals of this study were to investigate heavy metal and bioaugmentation effects on growth and nutrient uptake by Mucuna deeringiana; to determine the metal translocation factor and bioconcentration factor and provide insight for using native bacteria to enhance heavy metal accumulation. The experiment was conducted under greenhouse conditions using a 2 × 4 factorial scheme with highly and slightly contaminated soil samples and inoculating M. deeringiana with three highly lead (Pb +2 )-resistant bacteria Kluyvera intermedia (Ki), Klebsiella oxytoca (Ko), and Citrobacter murliniae (Cm) isolated from the rhizosphere of native plants identified as Senecio brasiliensis (Spreng.) Less., Senecio leptolobus DC., and Baccharis trimera (Less) DC., respectively. The increased heavy metal concentrations in soil samples do not decrease the root dry mass of M. deeringiana, concerning the number and dry weight of nodules. The shoot dry mass is reduced by the increasing concentration of heavy metals in soil associated with Kluyvera intermedia and Klebsiella oxytoca bacteria. The number of nodules is affected by heavy metals associated with Citrobacter murliniae bacteria. The bacteria K. intermedia, C. murliniae, and K. oxytoca increase the lead and cadmium available in the soil and enhanced metal uptake by Mucuna deeringiana. The M. deeringiana specie has characteristics that make it hyperaccumulate copper and zinc. The translocation and bioconcentration factors for M. deeringiana characterize it as a promising candidate to phytostabilize multi-metal contaminated soils.

Predictors of Heavy Stethoscope Contamination Following a Physical Examination.

Science.gov (United States)

Tschopp, Clément; Schneider, Alexis; Longtin, Yves; Renzi, Gesuele; Schrenzel, Jacques; Pittet, Didier

2016-06-01

BACKGROUND The degree of bacterial contamination of stethoscopes can vary significantly following a physical examination. OBJECTIVE To conduct a prospective study to investigate the impact of various environmental and patient characteristics on stethoscope contamination. METHODS Following a standardized examination, the levels of bacterial contamination of 4 regions of the physicians' hands and 2 sections of the stethoscopes, and the presence of different pathogenic bacteria, were assessed. Predictors of heavy stethoscope contamination were identified through multivariate logistic regression. RESULTS In total, 392 surfaces were sampled following examination of 56 patients. The microorganisms most frequently recovered from hands and stethoscopes were Enterococcus spp. (29% and 20%, respectively) and Enterobacteriaceae (16% and 7%, respectively). Staphylococcus aureus (either methicillin susceptible or resistant), extended-spectrum β-lactamase-producing Enterobacteriaceae, and Acinetobacter baumannii were recovered from 4%-9% of the samples from either hands or stethoscopes. There was a correlation between the likelihood of recovering these pathogens from the stethoscopes vs from the physicians' hands (ρ=0.79; P=.04). The level of patient's skin contamination was an independent predictor of contamination of the stethoscope diaphragm (adjusted odds ratio [aOR], 1.001; P=.007) and tube (aOR, 1.001; P=.003). Male sex (aOR, 28.24; P=.01) and reception of a bed bath (aOR, 7.52; P=.048) were also independently associated with heavy tube contamination. CONCLUSIONS Stethoscope contamination following a single physical examination is not negligible and is associated with the level of contamination of the patient's skin. Prevention of pathogen dissemination is needed. Infect Control Hosp Epidemiol 2016;37:673-679.

Disinfection of contaminated water by using solar irradiation.

Science.gov (United States)

Caslake, Laurie F; Connolly, Daniel J; Menon, Vilas; Duncanson, Catriona M; Rojas, Ricardo; Tavakoli, Javad

2004-02-01

Contaminated water causes an estimated 6 to 60 billion cases of gastrointestinal illness annually. The majority of these cases occur in rural areas of developing nations where the water supply remains polluted and adequate sanitation is unavailable. A portable, low-cost, and low-maintenance solar unit to disinfect unpotable water has been designed and tested. The solar disinfection unit was tested with both river water and partially processed water from two wastewater treatment plants. In less than 30 min in midday sunlight, the unit eradicated more than 4 log10 U (99.99%) of bacteria contained in highly contaminated water samples. The solar disinfection unit has been field tested by Centro Panamericano de Ingenieria Sanitaria y Ciencias del Ambiente in Lima, Peru. At moderate light intensity, the solar disinfection unit was capable of reducing the bacterial load in a controlled contaminated water sample by 4 log10 U and disinfected approximately 1 liter of water in 30 min.

Evaluation of antibiotic resistant bacteria in underground drinking water and transfer of their resistant character to normal flora of the body.

Science.gov (United States)

Alam, Mehboob; Khan, Naqab; Rehman, Khurram; Khan, Samiullah; Niazi, Zahid Rasul; Shah, Kifayatullah; Baloch, Natasha; Khan, Barkat Ali

2018-03-01

The untreated surface water for drinking and domestic use is an alarming situation to public health especially in prevalence of antibiotics resistant bacteria. This investigation aimed to isolate and identify the antibiotic resistance bacteria in underground water samples in district Dera Ismail Khan, Pakistan. The underground water samples were collected from four different places using hand pumps (Khyber town, riverside, Gomal University and united town). Cultured on nutrient agar media, identified by Gam staining and biochemical tests. There after antibiotic resistance assay were performed by measuring zone of inhibition of different antibiotics by disc diffusion method. Six different bacterial colonies were isolated and identified as Enterobacteriaceae, Serriata specie, Proteues, Pseudomonas, all these bacterial colonies were 33% resistant to chloramphenicol with and 100% resistant to amoxicillin. Some colonies were also considered as resistant, according to the criteria of National Committee for Clinical Records (NCCL) that less than 10mm zone of inhibition are considered as resistant. Subsequently, the chloramphenicol resistance bacteria were analyzed for their ability to transfer resistant gene to sensitive bacteria. In in-vitro method, an isolate M1b (resistant) was found capable to transfer resistance gene to M1a isolate (sensitive) in nutrient rich environment. It was concluded that antibiotics resistance bacteria found in underground water, moreover capable of transferring the antibiotic resistant character to suitable recipient i.e. normal flora of the body or to other pathogens by conjugation.

Bacteria from contaminated urban and hilly areas as a source of ...

African Journals Online (AJOL)

Polyhydroxyalkanoates (PHA) production and extraction of different bacterial strains isolated from contaminated urban and hilly areas was conducted. The 30 bacterial isolates were Gram negative and belonged to Pseudomonas, Citrobacter, Klebsiella, Escherichia and Enterobacter genera. Bacterial level of resistance ...

Bacterial metal resistance genes and metal bioavailability in contaminated sediments

International Nuclear Information System (INIS)

Roosa, Stéphanie; Wattiez, Ruddy; Prygiel, Emilie; Lesven, Ludovic; Billon, Gabriel; Gillan, David C.

2014-01-01

In bacteria a metal may be defined as bioavailable if it crosses the cytoplasmic membrane to reach the cytoplasm. Once inside the cell, specific metal resistance systems may be triggered. In this research, specific metal resistance genes were used to estimate metal bioavailability in sediment microbial communities. Gene levels were measured by quantitative PCR and correlated to metals in sediments using five different protocols to estimate dissolved, particle-adsorbed and occluded metals. The best correlations were obtained with czcA (a Cd/Zn/Co efflux pump) and Cd/Zn adsorbed or occluded in particles. Only adsorbed Co was correlated to czcA levels. We concluded that the measurement of czcA gene levels by quantitative PCR is a promising tool which may complement the classical approaches used to estimate Cd/Zn/Co bioavailability in sediment compartments. - Highlights: • Metal resistance genes were used to estimate metal bioavailability in sediments. • Gene levels were correlated to metals using 5 different metal extraction protocols. • CzcA gene levels determined by quantitative PCR is a promising tool for Cd/Zn/Co. - Capsule Bacterial czcA is a potential biomarker of Cd, Zn and Co bioavailability in aquatic sediments as shown by quantitative PCR and sequential metal extraction

Electrical Resistivity Measurements: a Review

Science.gov (United States)

Singh, Yadunath

World-wide interest on the use of ceramic materials for aerospace and other advanced engineering applications, has led to the need for inspection techniques capable of detecting unusually electrical and thermal anomalies in these compounds. Modern ceramic materials offer many attractive physical, electrical and mechanical properties for a wide and rapidly growing range of industrial applications; moreover specific use may be made of their electrical resistance, chemical resistance, and thermal barrier properties. In this review, we report the development and various techniques for the resistivity measurement of solid kind of samples.

The Potential of the Ni-Resistant TCE-Degrading Pseudomonas putida W619-TCE to Reduce Phytotoxicity and Improve Phytoremediation Efficiency of Poplar Cuttings on A Ni-TCE Co-Contamination.

Science.gov (United States)

Weyens, Nele; Beckers, Bram; Schellingen, Kerim; Ceulemans, Reinhart; van der Lelie, Daniel; Newman, Lee; Taghavi, Safiyh; Carleer, Robert; Vangronsveld, Jaco

2015-01-01

To examine the potential of Pseudomonas putida W619-TCE to improve phytoremediation of Ni-TCE co-contamination, the effects of inoculation of a Ni-resistant, TCE-degrading root endophyte on Ni-TCE phytotoxicity, Ni uptake and trichloroethylene (TCE) degradation of Ni-TCE-exposed poplar cuttings are evaluated. After inoculation with P. putida W619-TCE, root weight of non-exposed poplar cuttings significantly increased. Further, inoculation induced a mitigation of the Ni-TCE phytotoxicity, which was illustrated by a diminished exposure-induced increase in activity of antioxidative enzymes. Considering phytoremediation efficiency, inoculation with P. putida W619-TCE resulted in a 45% increased Ni uptake in roots as well as a slightly significant reduction in TCE concentration in leaves and TCE evapotranspiration to the atmosphere. These results indicate that endophytes equipped with the appropriate characteristics can assist their host plant to deal with co-contamination of toxic metals and organic contaminants during phytoremediation. Furthermore, as poplar is an excellent plant for biomass production as well as for phytoremediation, the obtained results can be exploited to produce biomass for energy and industrial feedstock applications in a highly productive manner on contaminated land that is not suited for normal agriculture. Exploiting this land for biomass production could contribute to diminish the conflict between food and bioenergy production.

Modeling Groundwater-Surface Water Interaction and Contaminant Transport of Chlorinated Solvent Contaminated Site

Science.gov (United States)

Yimer Ebrahim, Girma; Jonoski, Andreja; van Griensven, Ann; Dujardin, Juliette; Baetelaan, Okke; Bronders, Jan

2010-05-01

Chlorinated-solvent form one of the largest groups of environmental chemicals. Their use and misuse in industry have lead to a large entry of these chemicals into the environment, resulting in widespread dissemination and oftentimes environmental contamination. Chlorinated solvent contamination of groundwater resources has been widely reported. For instance, there has been much interest in the assessment of these contaminant levels and their evolutions with time in the groundwater body below the Vilvoorde-Machelen industrial area (Belgium). The long industrial history of the area has lead to complex patterns of pollution from multiple sources and the site has been polluted to the extent that individual plumes are not definable any more. Understanding of groundwater/surface water interaction is a critical component for determining the fate of contaminant both in streams and ground water due to the fact that groundwater and surface water are in continuous dynamic interaction in the hydrologic cycle. The interaction has practical consequences in the quantity and quality of water in either system in the sense that depletion and/or contamination of one of the system will eventually affect the other one. The transition zone between a stream and its adjacent aquifer referred to as the hyporheic zone plays a critical role in governing contaminant exchange and transformation during water exchange between the two water bodies. The hyporheic zone of Zenne River ( the main receptor ) is further complicated due to the fact that the river banks are artificially trained with sheet piles along its reach extending some 12 m below the surface. This study demonstrates the use of MODFLOW, a widely used modular three-dimensional block-centred finite difference, saturated flow model for simulating the flow and direction of movement of groundwater through aquifer and stream-aquifer interaction and the use of transport model RT3D, a three-dimensional multi-species reactive transport model

Detection of leaks in underground storage tanks using electrical resistance methods: 1996 results

International Nuclear Information System (INIS)

Ramirez, A.; Daily, W.

1996-10-01

This document provides a summary of a field experiment performed under a 15m diameter steel tank mockup located at the Hanford Reservation, Washington. The purpose of this test was to image a contaminant plume as it develops in soil under a tank already contaminated by previous leakage and to determine whether contaminant plumes can be detected without the benefit of background data. Measurements of electrical resistance were made before and during a salt water release. These measurements were made in soil which contained the remnants of salt water plumes released during previous tests in 1994 and in 1995. About 11,150 liters of saline solution were released along a portion of the tank's edge in 1996. Changes in electrical resistivity due to release of salt water conducted in 1996 were determined in two ways: (1) changes relative to the 1996 pre-spill data, and (2) changes relative to data collected near the middle of the 1996 spill after the release flow rate was increased. In both cases, the observed resistivity changes show clearly defined anomalies caused by the salt water release. These results indicate that when a plume develops over an existing plume and in a geologic environment similar to the test site environment, the resulting resistivity changes are easily detectable. Three dimensional tomographs of the resistivity of the soil under the tank show that the salt water release caused a region of low soil resistivity which can be observed directly without the benefit of comparing the tomograph to tomographs or data collected before the spill started. This means that it may be possible to infer the presence of pre-existing plumes if there is other data showing that the regions of low resistivity are correlated with the presence of contaminated soil. However, this approach does not appear reliable in defining the total extent of the plume due to the confounding effect that natural heterogeneity has on our ability to define the margins of the anomaly

A Fully Transparent Resistive Memory for Harsh Environments

KAUST Repository

Yang, Po-Kang; Ho, Chih-Hsiang; Lien, Der-Hsien; Duran Retamal, Jose Ramon; Kang, Chen-Fang; Chen, Kuan-Ming; Huang, Teng-Han; Yu, Yueh-Chung; Wu, Chih-I; He, Jr-Hau

2015-01-01

A fully transparent resistive memory (TRRAM) based on Hafnium oxide (HfO2) with excellent transparency, resistive switching capability, and environmental stability is demonstrated. The retention time measured at 85 °C is over 3 × 104 sec

Phytoextraction and estimating optimal time for remediation of Cd-contaminated soils by Spinach

OpenAIRE

Somayyeh Eisazadeh Lazarjan; safoora asadi kapourchal; Mehdi Homaee

2016-01-01

The so-called phytoextraction in which hyperaccumulator plants are used to remediate the contaminated soils is proven to be an efficient method. The objective of this study was to investigate the capability of Spinach for phytoremediation of cadmium from Cd-contaminated soils and determine the efficiency extent of spinach for phytoremediation. For this purpose, a randomized block experimental design whit five treatments including 0, 15, 30, 60 and 120 mg Cd/ kg soil and three replications was...

Advanced Simulation Capability for Environmental Management (ASCEM) Phase II Demonstration

Energy Technology Data Exchange (ETDEWEB)

Freshley, M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Hubbard, S. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Flach, G. [Savannah River National Lab. (SRNL), Aiken, SC (United States); Freedman, V. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Agarwal, D. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Andre, B. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Bott, Y. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Chen, X. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Davis, J. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Faybishenko, B. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Gorton, I. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Murray, C. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Moulton, D. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Meyer, J. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Rockhold, M. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Shoshani, A. [LBNL; Steefel, C. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Wainwright, H. [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Waichler, S. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2012-09-28

In 2009, the National Academies of Science (NAS) reviewed and validated the U.S. Department of Energy Office of Environmental Management (EM) Technology Program in its publication, Advice on the Department of Energy’s Cleanup Technology Roadmap: Gaps and Bridges. The NAS report outlined prioritization needs for the Groundwater and Soil Remediation Roadmap, concluded that contaminant behavior in the subsurface is poorly understood, and recommended further research in this area as a high priority. To address this NAS concern, the EM Office of Site Restoration began supporting the development of the Advanced Simulation Capability for Environmental Management (ASCEM). ASCEM is a state-of-the-art scientific approach that uses an integration of toolsets for understanding and predicting contaminant fate and transport in natural and engineered systems. The ASCEM modeling toolset is modular and open source. It is divided into three thrust areas: Multi-Process High Performance Computing (HPC), Platform and Integrated Toolsets, and Site Applications. The ASCEM toolsets will facilitate integrated approaches to modeling and site characterization that enable robust and standardized assessments of performance and risk for EM cleanup and closure activities. During fiscal year 2012, the ASCEM project continued to make significant progress in capabilities development. Capability development occurred in both the Platform and Integrated Toolsets and Multi-Process HPC Simulator areas. The new Platform and Integrated Toolsets capabilities provide the user an interface and the tools necessary for end-to-end model development that includes conceptual model definition, data management for model input, model calibration and uncertainty analysis, and model output processing including visualization. The new HPC Simulator capabilities target increased functionality of process model representations, toolsets for interaction with the Platform, and model confidence testing and verification for

A Novel Method for Remote Depth Estimation of Buried Radioactive Contamination.

Science.gov (United States)

Ukaegbu, Ikechukwu Kevin; Gamage, Kelum A A

2018-02-08

Existing remote radioactive contamination depth estimation methods for buried radioactive wastes are either limited to less than 2 cm or are based on empirical models that require foreknowledge of the maximum penetrable depth of the contamination. These severely limits their usefulness in some real life subsurface contamination scenarios. Therefore, this work presents a novel remote depth estimation method that is based on an approximate three-dimensional linear attenuation model that exploits the benefits of using multiple measurements obtained from the surface of the material in which the contamination is buried using a radiation detector. Simulation results showed that the proposed method is able to detect the depth of caesium-137 and cobalt-60 contamination buried up to 40 cm in both sand and concrete. Furthermore, results from experiments show that the method is able to detect the depth of caesium-137 contamination buried up to 12 cm in sand. The lower maximum depth recorded in the experiment is due to limitations in the detector and the low activity of the caesium-137 source used. Nevertheless, both results demonstrate the superior capability of the proposed method compared to existing methods.

High Prevalence of Multidrug-Resistant Community-Acquired Methicillin-Resistant Staphylococcus aureus at the Largest Veterinary Teaching Hospital in Costa Rica.

Science.gov (United States)

Rojas, Irene; Barquero-Calvo, Elías; van Balen, Joany C; Rojas, Norman; Muñoz-Vargas, Lohendy; Hoet, Armando E

2017-09-01

Methicillin-resistant Staphylococcus aureus (MRSA) is a pathogen associated with severe infections in companion animals present in the community, and it is diagnosed in animals admitted to veterinary hospitals. However, reports that describe the circulation of MRSA in animal populations and veterinary settings in Latin America are scarce. Therefore, the objective of this study was to determine the prevalence and investigate the molecular epidemiology of MRSA in the environment of the largest veterinary teaching hospital in Costa Rica. Preselected contact surfaces were sampled twice within a 6-week period. Antimicrobial resistance, SCCmec type, Panton-Valentine leukocidin screening, USA type, and clonality were assessed in all recovered isolates. Overall, MRSA was isolated from 26.5% (27/102) of the surfaces sampled, with doors, desks, and examination tables most frequently contaminated. Molecular analysis demonstrated a variety of surfaces from different sections of the hospital contaminated by three highly related clones/pulsotypes. All, but one of the isolates were characterized as multidrug-resistant SCCmec type IV-USA700, a strain sporadically described in other countries and often classified as community acquired. The detection and frequency of this unique strain in this veterinary setting suggest Costa Rica has a distinctive MRSA ecology when compared with other countries/regions. The high level of environmental contamination highlights the necessity to establish and enforce standard cleaning and disinfection protocols to minimize further spread of this pathogen and reduce the risk of nosocomial and/or occupational transmission of MRSA.

Identification of fecal contamination sources in water using host-associated markers.

Science.gov (United States)

Krentz, Corinne A; Prystajecky, Natalie; Isaac-Renton, Judith

2013-03-01

In British Columbia, Canada, drinking water is tested for total coliforms and Escherichia coli, but there is currently no routine follow-up testing to investigate fecal contamination sources in samples that test positive for indicator bacteria. Reliable microbial source tracking (MST) tools to rapidly test water samples for multiple fecal contamination markers simultaneously are currently lacking. The objectives of this study were (i) to develop a qualitative MST tool to identify fecal contamination from different host groups, and (ii) to evaluate the MST tool using water samples with evidence of fecal contamination. Singleplex and multiplex polymerase chain reaction (PCR) were used to test (i) water from polluted sites and (ii) raw and drinking water samples for presence of bacterial genetic markers associated with feces from humans, cattle, seagulls, pigs, chickens, and geese. The multiplex MST assay correctly identified suspected contamination sources in contaminated waterways, demonstrating that this test may have utility for heavily contaminated sites. Most raw and drinking water samples analyzed using singleplex PCR contained at least one host-associated marker. Singleplex PCR was capable of detecting host-associated markers in small sample volumes and is therefore a promising tool to further analyze water samples submitted for routine testing and provide information useful for water quality management.

Microbial interactions with organic contaminants in soil: Definitions, processes and measurement

International Nuclear Information System (INIS)

Semple, Kirk T.; Doick, Kieron J.; Wick, Lukas Y.; Harms, Hauke

2007-01-01

There has been and continues to be considerable scientific interest in predicting bioremediation rates and endpoints. This requires the development of chemical techniques capable of reliably predicting the bioavailability of organic compounds to catabolically active soil microbes. A major issue in understanding the link between chemical extraction and bioavailability is the problem of definition; there are numerous definitions, of varying degrees of complexity and relevance, to the interaction between organic contaminants and microorganisms in soil. The aim of this review is to consider the bioavailability as a descriptor for the rate and extent of biodegradation and, in an applied sense, bioremediation of organic contaminants in soil. To address this, the review will (i) consider and clarify the numerous definitions of bioavailability and discuss the usefulness of the term 'bioaccessibility'; (ii) relate definition to the microbiological and chemical measurement of organic contaminants' bioavailability in soil, and (iii) explore the mechanisms employed by soil microorganisms to attack organic contaminants in soil. - Understanding organic contaminant's behaviour in soil is key to chemically predicting biodegradation

Adaptation of microalgae to a gradient of continuous petroleum contamination

International Nuclear Information System (INIS)

Carrera-Martinez, Daniel; Mateos-Sanz, Aranzazu; Lopez-Rodas, Victoria; Costas, Eduardo

2011-01-01

In order to study adaptation of microalgae to petroleum contamination, we have examined an environmental stress gradient by crude oil contamination in the Arroyo Minero River (AMR), Argentina. Underground crude oil has constantly leaked out since 1915 as a consequence of test drilling for possible petroleum exploitation. Numerous microalgae species proliferated in AMR upstream of the crude oil spill. In contrast, only four microalgal species were detected in the crude oil spill area. Species richness increases again downstream. Microalgae biomass in the crude oil spill area is dominated by a mesophile species, Scenedesmus sp. Effects of oil samples from AMR spill on photosynthetic performance and growth were studied using laboratory cultures of two Scenedesmus sp. strains. One strain (Se-co) was isolated from the crude oil spill area. The other strain (Se-pr) was isolated from a pristine area without petroleum contamination. Crude oil has undetectable effects on Se-co strain. In contrast crude oil rapidly destroys Se-pr strain. However, Se-pr strain can adapt to low doses of petroleum (≤3% v/v total hydrocarbons/water) by means of physiological acclimatization. In contrast, only rare crude oil-resistant mutants are able to grow under high levels of crude oil (≥10% v/v total hydrocarbons/water). These crude oil-resistant mutants have arisen through rare spontaneous mutations that occur prior to crude oil exposure. Species richness in different areas of AMR is closely connected to the kind of mechanism (genetic adaptation vs. physiological acclimatization) that allows adaptation. Resistant-mutants are enough to assure the survival of microalgal species under catastrophic crude oil spill.

Biodegradation of organ chlorine pesticides in contaminated soil collected from Yen Tap, Cam Khe, Phu Tho

International Nuclear Information System (INIS)

Nguyen Thuy Binh; Nguyen Van Toan; Pham Thi Thai; Dinh Thi Thu Hang

2007-01-01

Biodegradation of POPs contaminant in soil collected from Phu Tho province and Nghe An province had carried out. The process comprises treating soil, which contains anaerobic and aerobic microbes capable of transforming lindane and DDT into harmless material and being under anaerobic and aerobic steps. Significant biodegradation of POPs contaminants occurred in there tests. But some of toxic organic compounds remained. (author)

Release of fission products from contaminated sodium fires

International Nuclear Information System (INIS)

Jordan, S.

1976-01-01

Leaks in the primary coolant system of a LMFBR and also serious incidents with tank rupture may entail the escape of fission products into the containment of the reactor. For incident analysis it is important to know the retention capability of sodium for the different fission products. The release of cesium and strontium from pools contaminated with 100 to 1000 ppM was investigated by experiments. The cesium content of airborne aerosols depends on oxygen concentration: at 21 percent oxygen concentration the Cs content of sodium-oxide aerosols is 3 times and at 0.5 percent 15 times as high as the initial Cs concentration in the pool. Strontium content of aerosols over burning contaminated sodium pools is 10 3 times smaller than the strontium pool concentration

Characterization of heavy metal-resistant endophytic bacteria from rape (Brassica napus) roots and their potential in promoting the growth and lead accumulation of rape

International Nuclear Information System (INIS)

Sheng Xiafang; Xia Juanjuan; Jiang Chunyu; He Linyan; Qian Meng

2008-01-01

Two lead (Pb)-resistant endophytic bacteria were isolated from rape roots grown in heavy metal-contaminated soils and characterized. A pot experiment was conducted for investigating the capability of the two isolates to promote the growth and Pb uptake of rape from Pb-amended soil. The two isolates were identified as Pseudomonas fluorescens G10 and Microbacterium sp. G16 based on the 16S rDNA gene sequence analysis. Strains G10 and G16 exhibited different multiple heavy metal and antibiotic resistance characteristics and increased water-soluble Pb in solution and in Pb-added soil. Root elongation assays demonstrated increases in root elongation of inoculated rape seedlings compared to the control plants. Strain G16 produced indole acetic acid, siderophores and 1-aminocyclopropane-1-carboxylate deaminase. Increases in biomass production and total Pb uptake in the bacteria-inoculated plants were obtained compared to the control. The two strains could colonize the root interior and rhizosphere soil of rape after root inoculation. - Heavy metal-resistant endophytic bacteria from rape have the potential of promoting the growth and lead uptake of rape

Boar semen bacterial contamination in Italy and antibiotic efficacy in a modified extender

Directory of Open Access Journals (Sweden)

Carla Bresciani

2014-02-01

Full Text Available The aims of the study were to identify microbial flora in boar semen under field conditions in northern Italy, to investigate antibiotic resistance and sensitivity of isolated bacteria, and to evaluate elimination of bacteria after storage in two types of extenders added with different antibiotics (amikacin vs gentamicin. A total of 60 boars were collected in 13 pig farms. Bacteriological and mycological investigations were performed immediately on raw semen samples, then at 48 and 120 h of storage on semen diluted randomly in a new short-term modified extender (ME-S or in a commercial one (CRONOSTM. Bacterial contamination was found in 63% of raw semen samples and different bacterial species were isolated: E.coli, Serratia marcescens, Staphylococcus epidermidis and aureus, Proteus spp., Streptococcus spp. and Pseudomonas aeruginosa. E. coli was the most isolated contaminant (53%; Pseudomonas aeruginosa was found only in one semen sample. The analysis of variance of factors affecting contamination levels was significant for the farm of origin (P<0.05 and not significant for the breed. Antibiotic resistance of these bacteria was assessed using different antibiotics. Significant differences (P<0.05 between observed and expected frequencies of bacterial isolates resistant or not to the antibiotics contained in the extenders were found. At 48 h of storage a reduction of aerobic contamination was found after ME-S dilution by 85.3% and after CRONOSTM by 63.8%. This paper proved the presence of pathogenic bacteria in semen. We thus believe it is highly advisable to perform periodic microbiological screening of boar semen in the swine industry to avoid the use of low sperm quality.

Heavy metal accumulation and phytostabilisation potential of tree fine roots in a contaminated soil

International Nuclear Information System (INIS)

Brunner, Ivano; Luster, Joerg; Guenthardt-Goerg, Madeleine S.; Frey, Beat

2008-01-01

Root systems of Norway spruce (Picea abies) and poplar (Populus tremula) were long-term exposed to metal-contaminated soils in open-top chambers to investigate the accumulation of the heavy metals in the fine roots and to assess the plants suitability for phytostabilisation. The heavy metals from the contaminated soil accumulated in the fine roots about 10-20 times more than in the controls. The capacity to bind heavy metals already reached its maximum after the first vegetation period. Fine roots of spruce tend to accumulate more heavy metals than poplar. Copper and Zinc were mainly detected in the cell walls with larger values in the epidermis than in the cortex. The heavy metals accumulated in the fine roots made up 0.03-0.2% of the total amount in the soils. We conclude that tree fine roots adapt well to conditions with heavy metal contamination, but their phytostabilisation capabilities seem to be very low. - Long-term exposed fine roots of trees are well adapted to soils with high heavy metal contents, but their phytostabilisation capabilities are rather low

Bacterial biodiversity analysis of a contaminated soil from the Chernobyl exclusion zone and characterization of the committed interaction of a Microbacterium strain with uranium

International Nuclear Information System (INIS)

Theodorakopoulos, Nicolas

2013-01-01

The nuclear power plants accidents of Chernobyl and Fukushima demonstrate the importance of the understanding of the transfer of the radioactive contamination in the environment and its ecological consequences. Although certain studies have been realized on superior organisms of the food chain, studies on telluric bacterial communities are scarce. The latter play nevertheless an essential role in the mobility of contaminants in soils by decreasing or improving their transfer towards other compartments (water, vegetables and animals). Moreover radionuclides (RNs) can have toxic effects on bacteria, leading to an inhibition of their participation in such transfer. The objectives of this study were (1) to estimate the impact of the radioactive contamination on bacterial communities belonging to a soil of the Chernobyl exclusion zone (trench T22) and (2) to study the uranium-bacteria interactions of a resistant strain, isolated from this soil. The various techniques used to characterize the bacterial diversity (culture of bacteria, DGGE, 454 pyro-sequencing) all testified of the multiplicity and the abundance of the bacterial communities in spite of the contamination. An impact on the community structure was difficult to assess by DGGE or cultural approach, but was nevertheless highlighted by the use of pyro-sequencing, suggesting the presence of species more adapted to the contaminated soil conditions. A specific molecular tool dedicated to the search of bacteria affiliated to the known radiation resistant Deinococcus-Thermus phylum (for example the Deinococcus radiodurans specie survives after an irradiation of several kGy) was developed. However it did not reveal the presence of bacteria affiliated to such a phylum in the studied soil. In parallel to the study of the bacterial biodiversity, about fifty culturable bacteria were isolated from this site and were used as a support to select a species (Microbacterium) capable to survive strong U(VI) concentrations. The

Structural Biology Meets Drug Resistance: An Overview on Multidrug Resistance Transporters

DEFF Research Database (Denmark)

Shaheen, Aqsa; Iqbal, Mazhar; Mirza, Osman

2017-01-01

. Research on the underlying causes of multidrug resistance in cancerous cells and later on in infectious bacteria revealed the involvement of integral membrane transporters, capable of recognizing a broad range of structurally different molecules as substrates and exporting them from the cell using cellular...... superfamilies, viz., ATP-binding cassette superfamily, major facilitator superfamily and resistance nodulation division superfamily are presented. Further, the future role of structural biology in improving our understanding of drug-transporter interactions and in designing novel inhibitors against MDR pump...... century, mankind has become aware and confronted with the emergence of antibiotic-resistant pathogens. In parallel to the failure of antibiotic therapy against infectious pathogens, there had been continuous reports of cancerous cells not responding to chemotherapy with increase in the duration of therapy...

Methicillin-Resistant Staphylococcus aureus (MRSA Contamination in Bedside Surfaces of a Hospital Ward and the Potential Effectiveness of Enhanced Disinfection with an Antimicrobial Polymer Surfactant

Directory of Open Access Journals (Sweden)

John W. M. Yuen

2015-03-01

Full Text Available The aim in this study was to assess the effectiveness of a quaternary ammonium chloride (QAC surfactant in reducing surface staphylococcal contamination in a routinely operating medical ward occupied by patients who had tested positive for methicillin-resistant Staphylococcus aureus (MRSA. The QAC being tested is an antibacterial film that is sprayed onto a surface and can remain active for up to 8 h. A field experimental study was designed with the QAC plus daily hypochlorite cleaning as the experimental group and hypochlorite cleaning alone as the control group. The method of swabbing on moistened surfaces was used for sampling. It was found that 83% and 77% of the bedside surfaces of MRSA-positive and MRSA-negative patients respectively were contaminated with staphylococci at 08:00 hours, and that the staphylococcal concentrations increased by 80% at 1200 h over a 4-hour period with routine ward and clinical activities. Irrespective of the MRSA status of the patients, high-touch surfaces around the bed-units within the studied medical ward were heavily contaminated (ranged 1 to 276 cfu/cm2 amongst the sites with positive culture with staphylococcal bacteria including MRSA, despite the implementation of daily hypochlorite wiping. However, the contamination rate dropped significantly from 78% to 11% after the application of the QAC polymer. In the experimental group, the mean staphylococcal concentration of bedside surfaces was significantly (p < 0.0001 reduced from 4.4 ± 8.7 cfu/cm2 at 08:00 hours to 0.07 ± 0.26 cfu/cm2 at 12:00 hours by the QAC polymer. The results of this study support the view that, in addition to hypochlorite wiping, the tested QAC surfactant is a potential environmental decontamination strategy for preventing the transmission of clinically important pathogens in medical wards.

Methicillin-resistant Staphylococcus aureus (MRSA) contamination in bedside surfaces of a hospital ward and the potential effectiveness of enhanced disinfection with an antimicrobial polymer surfactant.

Science.gov (United States)

Yuen, John W M; Chung, Terence W K; Loke, Alice Y

2015-03-11

The aim in this study was to assess the effectiveness of a quaternary ammonium chloride (QAC) surfactant in reducing surface staphylococcal contamination in a routinely operating medical ward occupied by patients who had tested positive for methicillin-resistant Staphylococcus aureus (MRSA). The QAC being tested is an antibacterial film that is sprayed onto a surface and can remain active for up to 8 h. A field experimental study was designed with the QAC plus daily hypochlorite cleaning as the experimental group and hypochlorite cleaning alone as the control group. The method of swabbing on moistened surfaces was used for sampling. It was found that 83% and 77% of the bedside surfaces of MRSA-positive and MRSA-negative patients respectively were contaminated with staphylococci at 08:00 hours, and that the staphylococcal concentrations increased by 80% at 1200 h over a 4-hour period with routine ward and clinical activities. Irrespective of the MRSA status of the patients, high-touch surfaces around the bed-units within the studied medical ward were heavily contaminated (ranged 1 to 276 cfu/cm2 amongst the sites with positive culture) with staphylococcal bacteria including MRSA, despite the implementation of daily hypochlorite wiping. However, the contamination rate dropped significantly from 78% to 11% after the application of the QAC polymer. In the experimental group, the mean staphylococcal concentration of bedside surfaces was significantly (p<0.0001) reduced from 4.4±8.7 cfu/cm2 at 08:00 hours to 0.07±0.26 cfu/cm2 at 12:00 hours by the QAC polymer. The results of this study support the view that, in addition to hypochlorite wiping, the tested QAC surfactant is a potential environmental decontamination strategy for preventing the transmission of clinically important pathogens in medical wards.

Geological characterization of contaminated sites near the city of Horsens, Denmark

DEFF Research Database (Denmark)

Andersen, Theis Raaschou; Poulsen, Søren Erbs; Thomsen, Peter

characterization of three contaminated sites situated in urban and semi-urban areas around the city of Horsens in corporation with authorities. The existing data from the three field sites include lithological profiles from boreholes. In order to increase the data density, Electrical Resistivity Tomography (ERT...

Evaluation of indigenously developed plastic scintillator sheet detector for surface radioactive contamination monitoring application

International Nuclear Information System (INIS)

Sahani, R.M.; Chaudhary, H.S.; Mahala, V.K.; Senwar, K.R.; Meena, J.P.

2018-01-01

Radioactive contamination may be caused by release of radioactivity in the environment due to accident at nuclear plant/reactor or spillage of loose radioactive materials in a laboratory. The protection of workers from potentially hazardous radiations emitted by the contaminants is a matter of prime concern. The detection of such radiations requires a monitoring system capable of measuring the level of radioactivity at the contaminated site. Plastic scintillators are widely used for large area radiation monitoring due to the ease of preparation in different shape and sizes. These detectors are sensitive to beta and gamma radiation therefore can be used for monitoring of beta and gamma contamination. In this paper, performance results of indigenously developed plastic scintillator sheet of area 800 cm 2 are reported

Phytoextraction and estimating optimal time for remediation of Cd-contaminated soils by Spinach

Directory of Open Access Journals (Sweden)

Somayyeh Eisazadeh Lazarjan

2016-05-01

Full Text Available The so-called phytoextraction in which hyperaccumulator plants are used to remediate the contaminated soils is proven to be an efficient method. The objective of this study was to investigate the capability of Spinach for phytoremediation of cadmium from Cd-contaminated soils and determine the efficiency extent of spinach for phytoremediation. For this purpose, a randomized block experimental design whit five treatments including 0, 15, 30, 60 and 120 mg Cd/ kg soil and three replications was established in the greenhouse. After contamination the soils with different levels of cadmium, spinach seeds were planted. When plants were fully developed, plants were harvested and their cadmium contents in shoot and roots as well as the soil-cadmium were measured. The results indicated that by increasing Cd concentration in soil, the major Cd accumulation was occurred in the roots rather than shoots. Maximum cadmium concentration within the shoots and roots was 73.7 and 75.86 mg/kg soil, respectively. According to Spinach ability to absorb high concentration of cadmium in the root zone and its high biomass and capability of Cadmium accumulation in shoots, Spinach can be used as hyperaccumulator plant to remediate cadmium from Cd-contaminated soils. But, according to minimum remediation time and maximum dry matter for the 30 mg Cd/ kg soil, maximum Cd extracted by shoots in hectare/year was in 30 mg Cd/ kg soil. It can be concluded that Spinach is a suitable plant for phytoremediation of slightly and to moderately cadmium contaminated soils.

Producing Biosurfactants from Purified Microorganisms Obtained from Oil-contaminated Soil

Directory of Open Access Journals (Sweden)

Nader Mokhtarian

2010-09-01

Full Text Available Contamination of soil by crude oil can pose serious problems to ecosystems. Soil washing by solutions containing biosurfactants is one of the most efficient methods for the remediation of contaminated soil by crude oil because it removes not only the crude oil but also heavy metals. In this study, five soil samples were taken from fields exposed to oil compounds over the years in order to produce biosurfactants from microorganisms that were capable of degrading oil compounds. Sixteen such microorganisms were isolated. After cultivation, their emulsification strength was examined using E24 test. From among the experimental microorganisms, a gram-negative and rod-shape microorganism called A-12 showed the greatest value of the E24 test index (36%. For each liter of the culture medium containing 365 mg of microorganisms, 3 gr of the biosurfactant compound was produced and separated as dried powder. The purified biosurfactant was used in the soil washing process. Also, the insulated microorganisms were capable of degrading crude oil floating on wastewaters.

Impact of urban contamination of the La Paz River basin on thermotolerant coliform density and occurrence of multiple antibiotic resistant enteric pathogens in river water, irrigated soil and fresh vegetables.

Science.gov (United States)

Poma, Violeta; Mamani, Nataniel; Iñiguez, Volga

2016-01-01

La Paz River in Andean highlands is heavily polluted with urban run-off and further contaminates agricultural lowlands and downstream waters at the Amazon watershed. Agricultural produce at this region is the main source of vegetables for the major Andean cities of La Paz and El Alto. We conducted a 1 year study, to evaluate microbial quality parameters and occurrence of multiple enteropathogenic bacteria (Enterohemorrhagic E. coli-EHEC, Enteroinvasive E. coli or Shigella-EIEC/Shigella, Enteroaggregative E. coli-EAEC, Enteropathogenic E. coli-EPEC Enterotoxigenic E. coli-ETEC and Salmonella) and its resistance to 11 antibiotics. Four sampling locations were selected: a fresh mountain water reservoir (un-impacted, site 1) and downstream sites receiving wastewater discharges (impacted, sites 2-4). River water (sites 1-4, N = 48), and soil and vegetable samples (site 3, N = 24) were collected during dry (April-September) and rainy seasons (October-March). Throughout the study, thermotolerant coliform density values at impacted sites greatly exceeded the guidelines for recreational and agricultural water uses. Seasonal differences were found for thermotolerant coliform density during dry season in water samples nearby a populated and hospital compound area. In contrast to the un-impacted site, where none of the tested enteropathogens were found, 100 % of surface water, 83 % of soil and 67 % of vegetable samples at impacted sites, were contaminated with at least one enteropathogen, being ETEC and Salmonella the most frequently found. ETEC isolates displayed different patterns of toxin genes among sites. The occurrence of enteropathogens was associated with the thermotolerant coliform density. At impacted sites, multiple enteropathogens were frequently found during rainy season. Among isolated enteropathogens, 50 % were resistant to at least two antibiotics, with resistance to ampicillin, nalidixic acid, trimethoprim-sulfamethoxazole and tetracycline commonly

Characteristics of surface mount low barrier silicon Schottky diodes with boron contamination in the substrate–epitaxial layer interface

International Nuclear Information System (INIS)

Pal, Debdas; Hoag, David; Barter, Margaret

2012-01-01

Unusual negative resistance characteristics were observed in low barrier HMIC (Heterolithic Microwave Integrated Circuit) silicon Schottky diodes with HF (hydrofluoric acid)/IPA (isopropyl alcohol) vapor clean prior to epitaxial growth of silicon. SIMS (secondary ion mass spectroscopy) analysis and the results of the buried layer structure confirmed boron contamination in the substrate/epitaxial layer interface. Consequently the structure turned into a thyristor like p-n-p-n device. A dramatic reduction of boron contamination was found in the wafers with H 2 0/HCl/HF dry only clean prior to growth, which provided positive resistance characteristics. Consequently the mean differential resistance at 10 mA was reduced to about 8.1 Ω. The lower series resistance (5.6–5.9 Ω) and near 1 ideality factor (1.03–1.06) of the Schottky devices indicated the good quality of the epitaxial layer. (paper)

Lead-resistant Providencia alcalifaciens strain 2EA bioprecipitates Pb+2 as lead phosphate.

Science.gov (United States)

Naik, M M; Khanolkar, D; Dubey, S K

2013-02-01

A lead-resistant bacteria isolated from soil contaminated with car battery waste were identified as Providencia alcalifaciens based on biochemical characteristics, FAME profile and 16S rRNA sequencing and designated as strain 2EA. It resists lead nitrate up to 0·0014 mol l(-1) by precipitating soluble lead as insoluble light brown solid. Scanning electron microscopy coupled with energy-dispersive X-ray spectrometric analysis (SEM-EDX) and X-ray diffraction spectroscopy (XRD) revealed extracellular light brown precipitate as lead orthophosphate mineral, that is, Pb(9) (PO(4))(6) catalysed by phosphatase enzyme. This lead-resistant bacterial strain also demonstrated tolerance to high levels of cadmium and mercury along with multiple antibiotic resistance. Providencia alcalifaciens strain 2EA could be used for bioremediation of lead-contaminated environmental sites, as it can efficiently precipitate lead as lead phosphate. © 2012 The Society for Applied Microbiology.

Contamination risk of stable isotope samples during milling.

Science.gov (United States)

Isaac-Renton, M; Schneider, L; Treydte, K

2016-07-15

Isotope analysis of wood is an important tool in dendrochronology and ecophysiology. Prior to mass spectrometry analysis, wood must be homogenized, and a convenient method involves a ball mill capable of milling samples directly in sample tubes. However, sample-tube plastic can contaminate wood during milling, which could lead to biological misinterpretations. We tested possible contamination of whole wood and cellulose samples during ball-mill homogenization for carbon and oxygen isotope measurements. We used a multi-factorial design with two/three steel milling balls, two sample amounts (10 mg, 40 mg), and two milling times (5 min, 10 min). We further analyzed abrasion by milling empty tubes, and measured the isotope ratios of pure contaminants. A strong risk exists for carbon isotope bias through plastic contamination: the δ(13) C value of polypropylene deviated from the control by -6.77‰. Small fibers from PTFE filter bags used during cellulose extraction also present a risk as the δ(13) C value of this plastic deviated by -5.02‰. Low sample amounts (10 mg) showed highest contamination due to increased abrasion during milling (-1.34‰), which is further concentrated by cellulose extraction (-3.38‰). Oxygen isotope measurements were unaffected. A ball mill can be used to homogenize samples within test tubes prior to oxygen isotope analysis, but not prior to carbon or radiocarbon isotope analysis. There is still a need for a fast, simple and contamination-free sample preparation procedure. Copyright © 2016 John Wiley & Sons, Ltd. Copyright © 2016 John Wiley & Sons, Ltd.

Detection of antibiotic resistance and tetracycline resistance genes in Enterobacteriaceae isolated from the Pearl rivers in South China

International Nuclear Information System (INIS)

Tao Ran; Ying Guangguo; Su Haochang; Zhou Hongwei; Sidhu, Jatinder P.S.

2010-01-01

This study investigated antibiotic resistance profiles and tetracycline resistance genes in Enterobacteriaceae family isolates from the Pearl rivers. The Enterobacteriaceae isolates were tested for susceptibility to seven antibiotics ampicillin, chloramphenicol, ciprofloxacin, levofloxacin, sulphamethoxazole/trimethoprim, tetracycline and trimethoprim. In Liuxi reservoir, with an exception to ampicillin resistant strains (11%) no other antibiotic resistance bacterial strains were detected. However, multiple drug resistance in bacterial isolates from the other sites of Pearl rivers was observed which is possibly due to sewage discharge and input from other anthropogenic sources along the rivers. Four tetracycline resistance genes tet A, tet B, tet C and tet D were detected in the isolates from the rivers. The genes tet A and tet B were widely detected with the detection frequencies of 43% and 40% respectively. Ciprofloxacin and levofloxacin resistant enteric bacteria were also isolated from the pig and duck manures which suggest a wider distribution of human specific drugs in the environment. This investigation provided a baseline data on antibiotic resistance profiles and tetracycline resistance genes in the Pearl rivers delta. - High rates of antibiotic resistance in Enterobacteriaceae from river water are attributed to wastewater contamination.

Detection of antibiotic resistance and tetracycline resistance genes in Enterobacteriaceae isolated from the Pearl rivers in South China

Energy Technology Data Exchange (ETDEWEB)

Tao Ran [State Key Laboratory of Organic Geochemistry, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, 511 Kehua Street, Tianhe District, Guangzhou 510640 (China); Ying Guangguo, E-mail: guangguo.ying@gmail.co [State Key Laboratory of Organic Geochemistry, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, 511 Kehua Street, Tianhe District, Guangzhou 510640 (China); Su Haochang [State Key Laboratory of Organic Geochemistry, Guangzhou Institute of Geochemistry, Chinese Academy of Sciences, 511 Kehua Street, Tianhe District, Guangzhou 510640 (China); Zhou Hongwei [Department of Environmental Health, School of Public Health and Tropical Medicine, Southern Medical University, 1838 North Guangzhou Street, Baiyun District, Guangzhou 510515 (China); Sidhu, Jatinder P.S. [CSIRO Land and Water, Queensland Bioscience Precinct, 306 Carmody Road, St Lucia QLD 4067 (Australia)

2010-06-15

This study investigated antibiotic resistance profiles and tetracycline resistance genes in Enterobacteriaceae family isolates from the Pearl rivers. The Enterobacteriaceae isolates were tested for susceptibility to seven antibiotics ampicillin, chloramphenicol, ciprofloxacin, levofloxacin, sulphamethoxazole/trimethoprim, tetracycline and trimethoprim. In Liuxi reservoir, with an exception to ampicillin resistant strains (11%) no other antibiotic resistance bacterial strains were detected. However, multiple drug resistance in bacterial isolates from the other sites of Pearl rivers was observed which is possibly due to sewage discharge and input from other anthropogenic sources along the rivers. Four tetracycline resistance genes tet A, tet B, tet C and tet D were detected in the isolates from the rivers. The genes tet A and tet B were widely detected with the detection frequencies of 43% and 40% respectively. Ciprofloxacin and levofloxacin resistant enteric bacteria were also isolated from the pig and duck manures which suggest a wider distribution of human specific drugs in the environment. This investigation provided a baseline data on antibiotic resistance profiles and tetracycline resistance genes in the Pearl rivers delta. - High rates of antibiotic resistance in Enterobacteriaceae from river water are attributed to wastewater contamination.

Reduction in infection risk through treatment of microbially contaminated surfaces with a novel, portable, saturated steam vapor disinfection system.

Science.gov (United States)

Tanner, Benjamin D

2009-02-01

Surface-mediated infectious disease transmission is a major concern in various settings, including schools, hospitals, and food-processing facilities. Chemical disinfectants are frequently used to reduce contamination, but many pose significant risks to humans, surfaces, and the environment, and all must be properly applied in strict accordance with label instructions to be effective. This study set out to determine the capability of a novel chemical-free, saturated steam vapor disinfection system to kill microorganisms, reduce surface-mediated infection risks, and serve as an alternative to chemical disinfectants. High concentrations of Escherichia coli, Shigella flexneri, vancomycin-resistant Enterococcus faecalis (VRE), methicillin-resistant Staphylococcus aureus (MRSA), Salmonella enterica, methicillin-sensitive Staphylococcus aureus, MS2 coliphage (used as a surrogate for nonenveloped viruses including norovirus), Candida albicans, Aspergillus niger, and the endospores of Clostridium difficile were dried individually onto porous clay test surfaces. Surfaces were treated with the saturated steam vapor disinfection system for brief periods and then numbers of surviving microorganisms were determined. Infection risks were calculated from the kill-time data using microbial dose-response relationships published in the scientific literature, accounting for surface-to-hand and hand-to-mouth transfer efficiencies. A diverse assortment of pathogenic microorganisms was rapidly killed by the steam disinfection system; all of the pathogens tested were completely inactivated within 5 seconds. Risks of infection from the contaminated surfaces decreased rapidly with increasing periods of treatment by the saturated steam vapor disinfection system. The saturated steam vapor disinfection system tested for this study is chemical-free, broadly active, rapidly efficacious, and therefore represents a novel alternative to liquid chemical disinfectants.

Total resistance of native bacteria as an indicator of changes in the water environment

Energy Technology Data Exchange (ETDEWEB)

Harnisz, Monika [Department of Environmental Microbiology, University of Warmia and Mazury in Olsztyn, Prawocheńskiego 1, 10-957 Olsztyn (Poland)

2013-03-15

This study analyzes changes in the total (intrinsic and acquired) resistance of autochthonous bacteria in a river which is a receiver of treated wastewater. In the analyzed samples, tetracycline contamination levels were low and characteristic of surface water bodies. An increase in the populations of tetracycline-resistant and fluoroquinolone-resistant microorganisms was noted in downstream river water samples in comparison with upstream river water samples, but the above trend was not observed in bacteria resistant to macrolides and β-lactams. The counts of doxycycline-resistant bacteria (DOX{sup R}) were significantly correlated with doxycycline levels. The minimum inhibitory concentrations (MICs) for doxycycline in DOX{sup R} isolates were higher in downstream river water than in upstream river water samples. The discharge of treated wastewater had no effect on the multi-drug resistance of oxytetracycline-resistant and doxycycline-resistant isolates. The results of the experiment indicate that the presence of doxycycline-resistant bacteria is a robust indicator of anthropogenic stress in river water. -- Highlights: ► The total resistance of native bacteria in river which is a receiver of treated wastewater was analyzed. ► Tetracyclines contamination levels were low. ► The counts of doxycycline-resistant bacteria were correlated with doxycycline levels. -- The presence of doxycycline-resistant bacteria in rivers can be a robust indicator of anthropogenic stress.

Total resistance of native bacteria as an indicator of changes in the water environment

International Nuclear Information System (INIS)

Harnisz, Monika

2013-01-01

This study analyzes changes in the total (intrinsic and acquired) resistance of autochthonous bacteria in a river which is a receiver of treated wastewater. In the analyzed samples, tetracycline contamination levels were low and characteristic of surface water bodies. An increase in the populations of tetracycline-resistant and fluoroquinolone-resistant microorganisms was noted in downstream river water samples in comparison with upstream river water samples, but the above trend was not observed in bacteria resistant to macrolides and β-lactams. The counts of doxycycline-resistant bacteria (DOX R ) were significantly correlated with doxycycline levels. The minimum inhibitory concentrations (MICs) for doxycycline in DOX R isolates were higher in downstream river water than in upstream river water samples. The discharge of treated wastewater had no effect on the multi-drug resistance of oxytetracycline-resistant and doxycycline-resistant isolates. The results of the experiment indicate that the presence of doxycycline-resistant bacteria is a robust indicator of anthropogenic stress in river water. -- Highlights: ► The total resistance of native bacteria in river which is a receiver of treated wastewater was analyzed. ► Tetracyclines contamination levels were low. ► The counts of doxycycline-resistant bacteria were correlated with doxycycline levels. -- The presence of doxycycline-resistant bacteria in rivers can be a robust indicator of anthropogenic stress

Characterization of Cd-, Pb-, Zn-resistant endophytic Lasiodiplodia sp. MXSF31 from metal accumulating Portulaca oleracea and its potential in promoting the growth of rape in metal-contaminated soils.

Science.gov (United States)

Deng, Zujun; Zhang, Renduo; Shi, Yang; Hu, Li'ao; Tan, Hongming; Cao, Lixiang

2014-02-01

The aim of this study was to characterize the features of a Cd-, Pb-, and Zn-resistant endophytic fungus Lasiodiplodia sp. MXSF31 and to investigate the potential of MXSF31 to remove metals from contaminated water and soils. The endophytic fungus was isolated from the stem of Portulaca oleracea growing in metal-contaminated soils. The maximum biosorption capacities of MXSF31 were 3.0 × 10(3), 1.1 × 10(4), and 1.3 × 10(4) mg kg(-1) for Cd, Pb, and Zn, respectively. The biosorption processes of Cd, Pb, and Zn by MXSF31 were well characterized with the pseudo-second-order kinetic model. The biosorption isotherm processes of Pb and Zn by the fungus were fitted better with the Langmuir model, while the biosorption processes of Cd was better fitted with the Freundlich model. The biosorption process of MXSF31 was attributed to the functional groups of hydroxyl, amino, carbonyl, and benzene ring on the cell wall. The active biomass of the strain removed more Cd, Pb, and Zn (4.6 × 10(4), 5.6 × 10(5), and 7.0 × 10(4) mg kg(-1), respectively) than the dead biomass. The inoculation of MXSF31 increased the biomass of rape (Brassica napus L.), the translocation factor of Cd, and the extraction amount of Cd by rape in the Cd+Pb-contaminated soils. The results indicated that the endophytic fungus strain had the potential to remove heavy metals from water and soils contaminated by multiple heavy metals, and plants accumulating multiple metals might harbor diverse fungi suitable for bioremediation of contaminated media.

Distribution of triclosan-resistant genes in major pathogenic microorganisms revealed by metagenome and genome-wide analysis.

Directory of Open Access Journals (Sweden)

Raees Khan

Full Text Available The substantial use of triclosan (TCS has been aimed to kill pathogenic bacteria, but TCS resistance seems to be prevalent in microbial species and limited knowledge exists about TCS resistance determinants in a majority of pathogenic bacteria. We aimed to evaluate the distribution of TCS resistance determinants in major pathogenic bacteria (N = 231 and to assess the enrichment of potentially pathogenic genera in TCS contaminated environments. A TCS-resistant gene (TRG database was constructed and experimentally validated to predict TCS resistance in major pathogenic bacteria. Genome-wide in silico analysis was performed to define the distribution of TCS-resistant determinants in major pathogens. Microbiome analysis of TCS contaminated soil samples was also performed to investigate the abundance of TCS-resistant pathogens. We experimentally confirmed that TCS resistance could be accurately predicted using genome-wide in silico analysis against TRG database. Predicted TCS resistant phenotypes were observed in all of the tested bacterial strains (N = 17, and heterologous expression of selected TCS resistant genes from those strains conferred expected levels of TCS resistance in an alternative host Escherichia coli. Moreover, genome-wide analysis revealed that potential TCS resistance determinants were abundant among the majority of human-associated pathogens (79% and soil-borne plant pathogenic bacteria (98%. These included a variety of enoyl-acyl carrier protein reductase (ENRs homologues, AcrB efflux pumps, and ENR substitutions. FabI ENR, which is the only known effective target for TCS, was either co-localized with other TCS resistance determinants or had TCS resistance-associated substitutions. Furthermore, microbiome analysis revealed that pathogenic genera with intrinsic TCS-resistant determinants exist in TCS contaminated environments. We conclude that TCS may not be as effective against the majority of bacterial pathogens as previously

Distribution of triclosan-resistant genes in major pathogenic microorganisms revealed by metagenome and genome-wide analysis

Science.gov (United States)

Khan, Raees; Roy, Nazish; Choi, Kihyuck

2018-01-01

The substantial use of triclosan (TCS) has been aimed to kill pathogenic bacteria, but TCS resistance seems to be prevalent in microbial species and limited knowledge exists about TCS resistance determinants in a majority of pathogenic bacteria. We aimed to evaluate the distribution of TCS resistance determinants in major pathogenic bacteria (N = 231) and to assess the enrichment of potentially pathogenic genera in TCS contaminated environments. A TCS-resistant gene (TRG) database was constructed and experimentally validated to predict TCS resistance in major pathogenic bacteria. Genome-wide in silico analysis was performed to define the distribution of TCS-resistant determinants in major pathogens. Microbiome analysis of TCS contaminated soil samples was also performed to investigate the abundance of TCS-resistant pathogens. We experimentally confirmed that TCS resistance could be accurately predicted using genome-wide in silico analysis against TRG database. Predicted TCS resistant phenotypes were observed in all of the tested bacterial strains (N = 17), and heterologous expression of selected TCS resistant genes from those strains conferred expected levels of TCS resistance in an alternative host Escherichia coli. Moreover, genome-wide analysis revealed that potential TCS resistance determinants were abundant among the majority of human-associated pathogens (79%) and soil-borne plant pathogenic bacteria (98%). These included a variety of enoyl-acyl carrier protein reductase (ENRs) homologues, AcrB efflux pumps, and ENR substitutions. FabI ENR, which is the only known effective target for TCS, was either co-localized with other TCS resistance determinants or had TCS resistance-associated substitutions. Furthermore, microbiome analysis revealed that pathogenic genera with intrinsic TCS-resistant determinants exist in TCS contaminated environments. We conclude that TCS may not be as effective against the majority of bacterial pathogens as previously presumed

Direct current contamination of kilohertz frequency alternating current waveforms.

Science.gov (United States)

Franke, Manfred; Bhadra, Niloy; Bhadra, Narendra; Kilgore, Kevin

2014-07-30

Kilohertz frequency alternating current (KHFAC) waveforms are being evaluated in a variety of physiological settings because of their potential to modulate neural activity uniquely when compared to frequencies in the sub-kilohertz range. However, the use of waveforms in this frequency range presents some unique challenges regarding the generator output. In this study we explored the possibility of undesirable contamination of the KHFAC waveforms by direct current (DC). We evaluated current- and voltage-controlled KHFAC waveform generators in configurations that included a capacitive coupling between generator and electrode, a resistive coupling and combinations of capacitive with inductive coupling. Our results demonstrate that both voltage- and current-controlled signal generators can unintentionally add DC-contamination to a KHFAC signal, and that capacitive coupling is not always sufficient to eliminate this contamination. We furthermore demonstrated that high value inductors, placed in parallel with the electrode, can be effective in eliminating DC-contamination irrespective of the type of stimulator, reducing the DC contamination to less than 1 μA. This study highlights the importance of carefully designing the electronic setup used in KHFAC studies and suggests specific testing that should be performed and reported in all studies that assess the neural response to KHFAC waveforms. Published by Elsevier B.V.

Hybrid Films Based on a Bridged Silsesquioxane Doped with Goethite and Montmorillonite Nanoparticles as Sorbents of Wastewater Contaminants

Directory of Open Access Journals (Sweden)

Carolina V. Waiman

2016-01-01

Full Text Available The synthesis and characterization of silsesquioxane (SSO films with pendant dodecyl groups and doped with goethite (Gt or montmorillonite (MMT nanoparticles were carried out and the new materials tested as sorbents of diverse contaminants. The synthetic method used yielded SSO films with the inorganic substrates homogeneously distributed within the polymeric matrices. The new materials were characterized by SEM, FTIR, XRD, and DSC and tested to evaluate their capability for adsorbing metallic cations, organic dyes, and phosphate, frequent contaminants of industrial effluents. All films were found suitable for removing metallic cations. Results also showed that the SSO films undoped and doped with Gt are primarily apt for anionic compounds removal. Although the SSO films doped with MMT are capable of removing cationic contaminants from aqueous samples, the stiffness of the SSO matrix hinders MMT properties as an adsorbent. The possibility of dispersing nanoparticulate systems in the stable and chemically inert SSO matrices simplifies their application for contaminant removal, particularly because it makes the separation process of the absorbed pollutant from the treated medium easier.

Antibiotic, Pesticide, and Microbial Contaminants of Honey: Human Health Hazards

Directory of Open Access Journals (Sweden)

Noori Al-Waili

2012-01-01

Full Text Available Agricultural contamination with pesticides and antibiotics is a challenging problem that needs to be fully addressed. Bee products, such as honey, are widely consumed as food and medicine and their contamination may carry serious health hazards. Honey and other bee products are polluted by pesticides, heavy metals, bacteria and radioactive materials. Pesticide residues cause genetic mutations and cellular degradation and presence of antibiotics might increase resistant human or animal's pathogens. Many cases of infant botulisms have been attributed to contaminated honey. Honey may be very toxic when produced from certain plants. Ingestion of honey without knowing its source and safety might be problematic. Honey should be labeled to explore its origin, composition, and clear statement that it is free from contaminants. Honey that is not subjected for analysis and sterilization should not be used in infants, and should not be applied to wounds or used for medicinal purposes. This article reviews the extent and health impact of honey contamination and stresses on the introduction of a strict monitoring system and validation of acceptable minimal concentrations of pollutants or identifying maximum residue limits for bee products, in particular, honey.

Application of diagnosis and monitoring area contaminated by petroleum derivatives; Aplicacao da tecnica de caminhamento eletrico em area contaminada por derivados de petroleo

Energy Technology Data Exchange (ETDEWEB)

Moreira, Cesar Augusto [Pos-graduacao em Geociencias em Meio Ambiente, IGCE - UNESP, Rio Claro, SP (Brazil)], E-mail: cesargeologia@yahoo.com.br; Dourado, Joao Carlos; Braga, Antonio Celso de Oliveira [Dept. de Geologia Aplicada, IGCE - UNESP, Rio Claro, SP (Brazil)], E-mails: jdourado@rc.unesp.br, acobraga@rc.unesp.br

2006-07-15

Geophysical methods are useful technic of geological investigation, thoroughly employed to diagnosis and monitoring contaminated areas, in conjunction with direct techniques of investigation such as chemical analyses. Among these, electric resistivity is more usually used in studies of contaminants in soil and groundwater, due to the high contrast of electric properties between the soil and the pollutant types frequently found, essentially constituted of composed organic and inorganic. Geophysical studies in impacted areas by petroleum products may be describe by anomalies of both low resistivity and high resistivities, confirmed as contaminant by chemical analyses. This apparent contradiction can reflect processes of degradation of the contaminants, directly associated with its residence time in the soil, through the generation of by-products that change the physical properties of the soil and groundwater, principally for the mineral dissolution by action of organic acids and by formation of minerals of oxides and hydroxides minerals. Natural attenuation defines a series of physical, chemical and biological processes that allow the degradation, dispersion and dilution of contaminants in a natural form, in other words, free from human intervention. This paper presents the application of electrical profiling technique in a contaminated industrial area for benzene, toluene, xylene, 1,2 dichloroethene and inorganic salts and it discusses the physical alterations of the contaminated soil through the obtained results, under the optics of the Natural Attenuation in course in the area of study. (author)

EMERGING TECHNOLOGY SUMMARY: VITRIFICATION OF SOILS CONTAMINATED BY HAZARDOUS AND/OR RADIOACTIVE WASTES

Science.gov (United States)

A performance summary of an advanced multifuel-capable combustion and melting system (CMS) for the vitrification of hazardous wastes is presented. Vortex Corporation has evaluated its patented CMS for use in the remediation of soils contaminated with heavy metals and radionuclid...

Removable coating for contamination protection of concrete surface

International Nuclear Information System (INIS)

Brambilla, G.; Beaulardi, L.

1985-01-01

In order to research protective coatings for concrete surfaces, assuring an effective protection against contamination and that it be easily removed before dismantling the structures, commercial stripping paints have been characterized for their conventional and nuclear properties: water and chemicals, abrasion, impact, tensile stress resistance, stripping capacity, decontaminability. The protective power of the coatings against contamination has been checked by recording the surface activity before and after stripping the paint film: the activity filtered through the coating was, in any case, very low (< 1% of the deposited activity). Indications from large scale application of a stripping paint in NUCLEO (Rome) establishments and technical evaluation of the possible utilization of removable coatings in the CAORSO Nuclear Power Station, are also reported

Effect of Long-Term Zinc Pollution on Soil Microbial Community Resistance to Repeated Contamination

OpenAIRE

Klimek, Beata

2012-01-01

The aim of the study was to compare the effects of stress (contamination trials) on the microorganisms in zinc-polluted soil (5,018 mg Zn kg−1 soil dry weight) and unpolluted soil (141 mg Zn kg−1 soil dw), measured as soil respiration rate. In the laboratory, soils were subjected to copper contamination (0, 500, 1,500 and 4,500 mg kg−1 soil dw), and then a bactericide (oxytetracycline) combined with a fungicide (captan) along with glucose (10 mg g−1 soil dw each) were added. There was a highl...

Phytoremediation of heavy metals and hydrocarbon contaminated soils; Phytoremediation des sols contamines aux metaux lourds et aux hydrocarbures recalcitrants

Energy Technology Data Exchange (ETDEWEB)

Leblanc, R.; Chateauneuf, G.; Sura, C. [Inspec-Sol Inc., Montreal, PQ (Canada); Labrecque, M.; Galipeau, C. [Jardin botanique de Montreal, Montreal, PQ (Canada). Institut de Recherche en Biologie Vegetale; Greer, C.; Delisle, S.; Roy, S.; Labelle, S. [National Research Council of Canada, Montreal, PQ (Canada). Inst. for Research in Biotechnology

2003-07-01

Phytoremediation is a technology that uses plants to decontaminate soils and underground water. Inspec-Sol, a company located in Montreal, Quebec, conducted a two-year study to evaluate the decontamination capabilities of this technology. Trials in greenhouses and field studies at the Pitt Park along the Lachine Canal were conducted. The soils chosen for the studies were soils with concentrations of polycyclic aromatic hydrocarbons (PAH) and heavy metals (lead, copper, zinc) higher than those prescribed for the safe utilization of soils. The trials identified the three plant species (Salix viminalis, Brassica juncea, and Festuca arundinacea) which had the best characteristics for phytoremediation. Controlled experiments were performed to optimize the technology to achieve the maximum extraction of contaminant. It was concluded that phytoremediation has potential for the remediation of urban soils contaminated with organic and inorganic pollutants.

The prevalence of pathogenic bacteria and antimicrobial resistance in milk of Ettawa Grade goat

Directory of Open Access Journals (Sweden)

A. Andriani

2018-05-01

Full Text Available Ettawa Grade (PE are potentially developed goats to produce milk and meat. Milk is food of animal that is rich in nutrients, but it is a perishable food easily contaminated by microorganisms. Contaminated pathogenic bacteria in milk can decrease the quality and has an organoleptic effect on milk, as well as endangers human health. Milk contaminated with bacteria antimicrobial resistance (AMR in which is resistant to antibiotics, may adversely affect the response to treatment with antibiotics in humans when suffering from infectious diseases and using antibiotics in therapy. In this study Ettawa Grade's samples of fresh milk and other dairy products were taken from some of the goat farms in Yogyakarta Sleman district. The samples were tested for the presence of pathogenic bacteria and for its resistance to several kinds of antibiotics. In this study 35 Ettawa Grade's samples of fresh milk and other dairy products (fresh milk, milk powder, ice cream, and yoghurt were taken from some of the goat farms in Sleman district-Yogyakarta. The samples were tested for the presence of pathogenic bacteria and for its resistance to several kinds of antibiotics. The result of the prevalence of pathogenic bacteria in goat fresh milk and other dairy products was 15% Escherichia coli and had multi resistance to multiple antibiotics, namely ampicillin, colistin sulphate, cefixime, kanamycin, oxytetracycline, tetracycline and sulfonamide.

High counting rate resistive-plate chamber

International Nuclear Information System (INIS)

Peskov, V.; Anderson, D.F.; Kwan, S.

1993-05-01

Parallel-plate avalanche chambers (PPAC) are widely used in physics experiments because they are fast ( 5 counts/mm 2 . A resistive-plate chamber (RPC) is similar to the PPAC in construction except that one or both of the electrodes are made from high resistivity (≥10 10 Ω·cm) materials. In practice RPCs are usually used in the spark mode. Resistive electrodes are charged by sparks, locally reducing the actual electric field in the gap. The size of the charged surface is about 10 mm 2 , leaving the rest of the detector unaffected. Therefore, the rate capability of such detectors in the spark mode is considerably higher than conventional spark counters. Among the different glasses tested the best results were obtained with electron type conductive glasses, which obey Ohm's law. Most of the work with such glasses was done with high pressure parallel-plate chambers (10 atm) for time-of-flight measurements. Resistive glasses have been expensive and produced only in small quantities. Now resistive glasses are commercially available, although they are still expensive in small scale production. From the positive experience of different groups working with the resistive glasses, it was decided to review the old idea to use this glass for the RPC. This work has investigated the possibility of using the RPC at 1 atm and in the avalanche mode. This has several advantages: simplicity of construction, high rate capability, low voltage operation, and the ability to work with non-flammable gases

Environmental contamination with Staphylococcus aureus at a large, Midwestern university campus.

Science.gov (United States)

Thapaliya, Dipendra; Taha, Mohammed; Dalman, Mark R; Kadariya, Jhalka; Smith, Tara C

2017-12-01

Staphylococcus aureus can cause minor to severe life-threatening infections. The changing epidemiology of S. aureus is of public health concern due to the emergence of multi-drug resistant (MDR) strains. Environmental surfaces play a crucial role in the transmission of S. aureus. The objective of this study was to examine environmental contamination and molecular characteristics of S. aureus in health professional-associated (HPA) and non-health professional-associated (NHPA) buildings at a large university. A total of 152 environmental surface samples were collected from two HPA and two NHPA campus buildings. Bacterial culture and diagnostics were done using standard microbiology methods. Polymerase chain reaction was conducted to detect mecA and PVL genes. All isolates were spa typed. A subset of isolates was characterized via multi-locus sequence typing (MLST). All S. aureus isolates were tested for antibiotic susceptibility. The overall contamination of S. aureus and methicillin-resistant S. aureus (MRSA) was 22.4% (34/152) and 5.9% (9/152) respectively. Similar prevalence of contamination was found in HPA and NHPA buildings. A total of 17 different spa types were detected among 34 S. aureus isolates. The majority of the MRSA isolates belonged to clonal complex (CC) 8. One isolate was positive for PVL. Eleven different sequence types (STs) were detected from 17 tested isolates. ST8 was the most common. Twelve isolates (35.3%) were MDR. Almost 27% (9/34) of the isolates were MRSA. The highest contamination of S. aureus was found in high hand-touch areas such as door knobs, suggesting that human interaction in crowded environments such as academic institutions plays a crucial role in S. aureus/MRSA transmission via inanimate objects. Additionally, more than one-third of the isolates were MDR. These data reinforce the need to implement effective prevention strategies outside the healthcare setting to decrease the incidence of drug-resistant S. aureus infections

Effects of Cd, Pb, Zn, Cu-resistant endophytic Enterobacter sr CBSB1 and Rhodotorula sp. CBSB79 on the growth and phytoextraction of Brassica plants in multimetal contaminated soils.

Science.gov (United States)

Wang, Wenfeng; Deng, Zujun; Tan, Hongming; Cao, Lixiang

2013-01-01

To survey the effects of endophytic Enterobacter sp. CBSB1 and Rhodotorula sp. CBSB79 resistant to Cd2+, Pb2+, Zn2+, and Cu2+ on the growth and phytoextraction of Brassica, the endophytes were isolated by surface- sterilized methods and characterized. The CBSB1 significantly increased 44.2% of the dry weight of Brassica napus in the multimetal contaminated soil (P Rhodotorula sp CBSB79 showed higher potentials to improve extraction efficacy of Cd, Pb, Zn, and Cu by Brassica seedlings in the field.

Small scale monitoring of a bioremediation barrier using miniature electrical resistivity tomography

Science.gov (United States)

Sentenac, Philippe; Hogson, Tom; Keenan, Helen; Kulessa, Bernd

2015-04-01

The aim of this study was to assess, in the laboratory, the efficiency of a barrier of oxygen release compound (ORC) to block and divert a diesel plume migration in a scaled aquifer model using miniature electrical resistivity tomography (ERT) as the monitoring system. Two plumes of contaminant (diesel) were injected in a soil model made of local sand and clay. The diesel plumes migration was imaged and monitored using a miniature resistivity array system that has proved to be accurate in soil resistivity variations in small-scaled models of soil. ERT results reflected the lateral spreading and diversion of the diesel plumes in the unsaturated zone. One of the contaminant plumes was partially blocked by the ORC barrier and a diversion and reorganisation of the diesel in the soil matrix was observed. The technique of time-lapse ERT imaging showed that a dense non-aqueous phase liquid (DNAPL) contaminant like diesel can be monitored through a bioremediation barrier and the technique is well suited to monitor the efficiency of the barrier. Therefore, miniature ERT as a small-scale modelling tool could complement conventional techniques, which require more expensive and intrusive site investigation prior to remediation.

Meta-transcriptomics indicates biotic cross-tolerance in willow trees cultivated on petroleum hydrocarbon contaminated soil.

Science.gov (United States)

Gonzalez, Emmanuel; Brereton, Nicholas J B; Marleau, Julie; Guidi Nissim, Werther; Labrecque, Michel; Pitre, Frederic E; Joly, Simon

2015-10-12

High concentrations of petroleum hydrocarbon (PHC) pollution can be hazardous to human health and leave soils incapable of supporting agricultural crops. A cheap solution, which can help restore biodiversity and bring land back to productivity, is cultivation of high biomass yielding willow trees. However, the genetic mechanisms which allow these fast-growing trees to tolerate PHCs are as yet unclear. Salix purpurea 'Fish Creek' trees were pot-grown in soil from a former petroleum refinery, either lacking or enriched with C10-C50 PHCs. De novo assembled transcriptomes were compared between tree organs and impartially annotated without a priori constraint to any organism. Over 45% of differentially expressed genes originated from foreign organisms, the majority from the two-spotted spidermite, Tetranychus urticae. Over 99% of T. urticae transcripts were differentially expressed with greater abundance in non-contaminated trees. Plant transcripts involved in the polypropanoid pathway, including phenylalanine ammonia-lyase (PAL), had greater expression in contaminated trees whereas most resistance genes showed higher expression in non-contaminated trees. The impartial approach to annotation of the de novo transcriptomes, allowing for the possibility for multiple species identification, was essential for interpretation of the crop's response treatment. The meta-transcriptomic pattern of expression suggests a cross-tolerance mechanism whereby abiotic stress resistance systems provide improved biotic resistance. These findings highlight a valuable but complex biotic and abiotic stress response to real-world, multidimensional contamination which could, in part, help explain why crops such as willow can produce uniquely high biomass yields on challenging marginal land.

Development of a CB Resistant Durable, Flexible Hydration System

National Research Council Canada - National Science Library

Hall, Peyton W; Zeller, Frank T; Bulluck, John W; Dingus, Michael L

2002-01-01

A durable, flexible hydration system resistant to contamination by contact with VX, GD, and HD chemical agents, as well as damage by the decontaminants sodium hypochlorite and DS-2 is being developed for aviator use...

Antimicrobial resistance mechanisms among Campylobacter.

Science.gov (United States)

Wieczorek, Kinga; Osek, Jacek

2013-01-01

Campylobacter jejuni and Campylobacter coli are recognized as the most common causative agents of bacterial gastroenteritis in the world. Humans most often become infected by ingesting contaminated food, especially undercooked chicken, but also other sources of bacteria have been described. Campylobacteriosis is normally a self-limiting disease. Antimicrobial treatment is needed only in patients with more severe disease and in those who are immunologically compromised. The most common antimicrobial agents used in the treatment of Campylobacter infections are macrolides, such as erythromycin, and fluoroquinolones, such as ciprofloxacin. Tetracyclines have been suggested as an alternative choice in the treatment of clinical campylobacteriosis but in practice are not often used. However, during the past few decades an increasing number of resistant Campylobacter isolates have developed resistance to fluoroquinolones and other antimicrobials such as macrolides, aminoglycosides, and beta-lactams. Trends in antimicrobial resistance have shown a clear correlation between use of antibiotics in the veterinary medicine and animal production and resistant isolates of Campylobacter in humans. In this review, the patterns of emerging resistance to the antimicrobial agents useful in treatment of the disease are presented and the mechanisms of resistance to these drugs in Campylobacter are discussed.

Geophysics Based Contaminant Mass Discharge Quantification Downgradient of a Landfill and a Former Pharmaceutical Factory

DEFF Research Database (Denmark)

Balbarini, Nicola; Rønde, Vinni Kampman; Maurya, Pradip

2018-01-01

Contaminant mass discharge is a commonly applied tool to evaluate the environmental impact of contaminated sites on water resources. At large contaminated sites with heterogeneous sources, such as landfills, the number of wells available is often not sufficient, leading to a high uncertainty...... of mass discharge estimates. In this study, we tackle the uncertainty of the contaminant mass discharge due to low sampling densities by interpolating limited water‐sample data with the support of surface Direct Current resistivity and Induced Polarization geophysical data. The method relies on finding...... a conceptual link between the bulk conductivity imaged from geophysics and the contaminant concentrations. We investigate the link between: 1) imaged bulk and electrical water conductivity, 2) water conductivity and conservative ionic species, 3) water conductivity and redox‐sensitive species, 4) water...

Measurement of residual radioactive surface contamination by 2-D laser heated TLD

International Nuclear Information System (INIS)

Jones, S.C.

1997-06-01

The feasibility of applying and adapting a two-dimensional laser heated thermoluminescence dosimetry system to the problem of surveying for radioactive surface contamination was studied. The system consists of a CO 2 laser-based reader and monolithic arrays of thin dosimeter elements. The arrays consist of 10,201 thermoluminescent phosphor elements of 40 micron thickness, covering a 900 cm 2 area. Array substrates are 125 micron thick polyimide sheets, enabling them to easily conform to regular surface shapes, especially for survey of surfaces that are inaccessible for standard survey instruments. The passive, integrating radiation detectors are sensitive to alpha and beta radiation at contamination levels below release guideline limits. Required contact times with potentially contaminated surfaces are under one hour to achieve detection of transuranic alpha emission at 100 dpm/100 cm 2 . Positional information obtained from array evaluation is useful for locating contamination zones. Unique capabilities of this system for survey of sites, facilities and material include measurement inside pipes and other geometrical configurations that prevent standard surveys, and below-surface measurement of alpha and beta emitters in contaminated soils. These applications imply a reduction of material that must be classified as radioactive waste by virtue of its possibility of contamination, and cost savings in soil sampling at contaminated sites

Culture-dependent and independent studies of microbial diversity in highly copper-contaminated Chilean marine sediments.

Science.gov (United States)

Besaury, Ludovic; Marty, Florence; Buquet, Sylvaine; Mesnage, Valérie; Muyzer, Gerard; Quillet, Laurent

2013-02-01

Cultivation and molecular-based approaches were used to study microbial diversity in two Chilean marine sediments contaminated with high (835 ppm) and very high concentrations of copper (1,533 ppm). The diversity of cultivable bacteria resistant to copper was studied at oxic and anoxic conditions, focusing on sulfate-, thiosulfate-, and iron-reducing bacteria. For both sediments, the cultivable bacteria isolated at oxic conditions were mostly affiliated to the genus Bacillus, while at anoxic conditions the majority of the cultivable bacteria found were closely related to members of the genera Desulfovibrio, Sphingomonas, and Virgibacillus. Copper resistance was between 100 and 400 ppm, with the exception of a strain affiliated to members of the genus Desulfuromonas, which was resistant up to 1,000 ppm of copper. In parallel, cloning and sequencing of 16S rRNA was performed to study the total bacterial diversity in the sediments. A weak correlation was observed between the isolated strains and the 16S rRNA operational taxonomic units detected. The presence of copper resistance genes (copA, cusA, and pcoA) was tested for all the strains isolated; only copA was detected in a few isolates, suggesting that other copper resistance mechanisms could be used by the bacteria in those highly copper-contaminated sediments.

Effects of cation contaminants in conductive TiO2 ceramics

Science.gov (United States)

Yan, M. F.; Rhodes, W. W.

1982-12-01

Ten cation contaminants, namely Al, Ga, Co, Fe, Mg, Zn, Zr, Ca, Sr, and Ba were investigated for their effects on the electrical properties, microstructures, and discoloration of conductive TiO2 ceramics. It was found that Al, Ga, Co, Fe, and Mg cause discoloration and increase the electrical resistivity by a factor of 104 to 106 in Nb-doped TiO2 ceramics. The other dopants do not introduce such changes in TiO2. The electrical properties, microstructures, and discoloration were measured in specimens of AlxNb0.007Ti0.993-xO2 with 0≤x≤0.01. When the Al content exceeds a critical value, ranging from 0.48% at 1400 °C to 0.25% at 1200 °C, the electrical resistivities and grain size increase rapidly, and the specimen is discolored from the original black to an ivory white color. Color boundary migration induced by Al diffusion in Nb-doped TiO2 was quantitatively measured. From the kinetics of the boundary migration, the Al diffusivity (D) was calculated to be D=2.67 exp(-53.3 kcal/mole/RT) cm2/s in the temperature range of 1200 to 1400 °C. The rapid diffusion of the small cations, namely Al, Ga, Co, Fe, and Mg, results from an interstitial diffusion mechanism. However, other cations, having a radius larger than the interstitial channel (˜0.77 Å radius), cannot diffuse by this mechanism. Defect reactions are proposed to explain the increase in the electrical resistivity and microstructural changes due to Al diffusion. These defect reactions also show that the problem of acceptor contamination cannot be avoided by adding an excess quantity of donor dopant if the solubility of the donor is much less than that of the acceptor contaminant.

Impact of Personnel Capabilities on Organizational Innovation Capability

DEFF Research Database (Denmark)

Nielsen, Susanne Balslev; Momeni, Mostafa

2016-01-01

in this rapidly changing world. This research focuses on definition of the personnel aspect of innovation capability, and proposes a conceptual model based on the scientific articles of academic literature on organisations innovation capability. This paper includes an expert based validation in three rounds...... of the Delphi method. And for the purpose of a better appreciation of the relationship dominating the factors of the model, it has distributed the questionnaire to Iranian companies in the Food industry. This research proposed a direct relationship between Innovation Capability and the Personnel Capability...

A novel approach for the detection of potentially hazardous pepsin stable hazelnut proteins as contaminants in chocolate-based food

NARCIS (Netherlands)

Akkerdaas, Jaap H.; Wensing, Marjolein; Knulst, André C.; Stephan, Oliver; Hefle, Susan L.; Aalberse, Rob C.; van Ree, Ronald

2004-01-01

Contamination of food products with pepsin resistant allergens is generally believed to be a serious threat to patients with severe food allergy. A sandwich type enzyme-linked immunosorbent assay (ELISA) was developed to measure pepsin resistant hazelnut protein in food products. Capturing and

An underappreciated hotspot of antibiotic resistance

DEFF Research Database (Denmark)

Chen, Qing-Lin; Li, Hu; Zhou, Xin-Yuan

2017-01-01

Landfills are so far the most common practice for the disposals of municipal solid waste (MSW) worldwide. Since MSW landfill receives miscellaneous wastes, including unused/expired antibiotics and bioactive wastes, it gradually becomes a huge potential bioreactor for breeding antibiotic resistance....... Antibiotic resistance genes (ARGs) in landfill can flow to the environment through leakage of landfill leachate and pose a risk to public health. Using high throughput quantitative Polymerase Chain Reaction (HT-qPCR), we investigated the prevalence, diversity of ARGs and its association with various mobile...... be the potential hosts of ARGs. These findings provide evidence that groundwater near MSW landfill is an underappreciated hotspot of antibiotic resistance and contribute to the spread of ARGs via the flowing contaminated groundwater....

Arsenic-contaminated soils. Genetically modified Pseudomonas spp. and their arsenic-phytoremediation potential

Energy Technology Data Exchange (ETDEWEB)

Sizova, O.I.; Kochetkov, V.V.; Validov, S.Z.; Boronin, A.M. [Inst. of Biochemistry and Physiology of Microorganisms, Russian Academy of Sciences, Moscow (Russian Federation); Kosterin, P.V.; Lyubun, Y.V. [Inst. of Biochemistry and Physiology of Plants and Microorganisms, Russian Academy of Sciences, Saratov (Russian Federation)

2002-07-01

Sorghum was inoculated with Pseudomonas bacteria, including strains harboring an As-resistance plasmid, pBS3031, to enhance As-extraction by the plants. Pseudomonas strains (P. fluorescens 38a, P. putida 53a, and P. aureofaciens BS1393) were chosen because they are antagonistic to a wide range of phytopathogenic fungi and bacteria, and they can stimulate plant growth. The resistance of natural rhizospheric pseudomonads to sodium arsenite was assessed. Genetically modified Pseudomonas strains resistant to As(III)/As(V) were obtained via conjugation or transformation. The effects of the strains on the growth of sorghum on sodium-arsenite-containing soils were assessed. The conclusions from this study are: (1) It is possible to increase the survivability of sorghum growing in sodium-arsenite-containing soil by using rhizosphere pseudomonads. (2) The presence of pBS3031 offers the strains a certain selective advantage in arsenite-contaminated soil. (3) The presence of pBS3031 impairs plant growth, due to the As-resistance mechanism determined by this plasmid: the transformation of the less toxic arsenate into the more toxic, plant-root-available arsenite by arsenate reductase and the active removal of arsenite from bacterial cells. (4) Such a mechanism makes it possible to develop a bacteria-assisted phytoremediation technology for the cleanup of As-contaminated soils and is the only possible way of removing the soil-sorbed arsenates from the environment. (orig.)

Evaluation and study of advanced optical contamination, deposition, measurement, and removal techniques. [including computer programs and ultraviolet reflection analysis

Science.gov (United States)

Linford, R. M. F.; Allen, T. H.; Dillow, C. F.

1975-01-01

A program is described to design, fabricate and install an experimental work chamber assembly (WCA) to provide a wide range of experimental capability. The WCA incorporates several techniques for studying the kinetics of contaminant films and their effect on optical surfaces. It incorporates the capability for depositing both optical and contaminant films on temperature-controlled samples, and for in-situ measurements of the vacuum ultraviolet reflectance. Ellipsometer optics are mounted on the chamber for film thickness determinations, and other features include access ports for radiation sources and instrumentation. Several supporting studies were conducted to define specific chamber requirements, to determine the sensitivity of the measurement techniques to be incorporated in the chamber, and to establish procedures for handling samples prior to their installation in the chamber. A bibliography and literature survey of contamination-related articles is included.

Characterization of the Metabolically Modified Heavy Metal-Resistant Cupriavidus metallidurans Strain MSR33 Generated for Mercury Bioremediation

Science.gov (United States)

Rojas, Luis A.; Yáñez, Carolina; González, Myriam; Lobos, Soledad; Smalla, Kornelia; Seeger, Michael

2011-01-01

Background Mercury-polluted environments are often contaminated with other heavy metals. Therefore, bacteria with resistance to several heavy metals may be useful for bioremediation. Cupriavidus metallidurans CH34 is a model heavy metal-resistant bacterium, but possesses a low resistance to mercury compounds. Methodology/Principal Findings To improve inorganic and organic mercury resistance of strain CH34, the IncP-1β plasmid pTP6 that provides novel merB, merG genes and additional other mer genes was introduced into the bacterium by biparental mating. The transconjugant Cupriavidus metallidurans strain MSR33 was genetically and biochemically characterized. Strain MSR33 maintained stably the plasmid pTP6 over 70 generations under non-selective conditions. The organomercurial lyase protein MerB and the mercuric reductase MerA of strain MSR33 were synthesized in presence of Hg2+. The minimum inhibitory concentrations (mM) for strain MSR33 were: Hg2+, 0.12 and CH3Hg+, 0.08. The addition of Hg2+ (0.04 mM) at exponential phase had not an effect on the growth rate of strain MSR33. In contrast, after Hg2+ addition at exponential phase the parental strain CH34 showed an immediate cessation of cell growth. During exposure to Hg2+ no effects in the morphology of MSR33 cells were observed, whereas CH34 cells exposed to Hg2+ showed a fuzzy outer membrane. Bioremediation with strain MSR33 of two mercury-contaminated aqueous solutions was evaluated. Hg2+ (0.10 and 0.15 mM) was completely volatilized by strain MSR33 from the polluted waters in presence of thioglycolate (5 mM) after 2 h. Conclusions/Significance A broad-spectrum mercury-resistant strain MSR33 was generated by incorporation of plasmid pTP6 that was directly isolated from the environment into C. metallidurans CH34. Strain MSR33 is capable to remove mercury from polluted waters. This is the first study to use an IncP-1β plasmid directly isolated from the environment, to generate a novel and stable bacterial strain

Characterization of the metabolically modified heavy metal-resistant Cupriavidus metallidurans strain MSR33 generated for mercury bioremediation.

Directory of Open Access Journals (Sweden)

Luis A Rojas

Full Text Available BACKGROUND: Mercury-polluted environments are often contaminated with other heavy metals. Therefore, bacteria with resistance to several heavy metals may be useful for bioremediation. Cupriavidus metallidurans CH34 is a model heavy metal-resistant bacterium, but possesses a low resistance to mercury compounds. METHODOLOGY/PRINCIPAL FINDINGS: To improve inorganic and organic mercury resistance of strain CH34, the IncP-1β plasmid pTP6 that provides novel merB, merG genes and additional other mer genes was introduced into the bacterium by biparental mating. The transconjugant Cupriavidus metallidurans strain MSR33 was genetically and biochemically characterized. Strain MSR33 maintained stably the plasmid pTP6 over 70 generations under non-selective conditions. The organomercurial lyase protein MerB and the mercuric reductase MerA of strain MSR33 were synthesized in presence of Hg(2+. The minimum inhibitory concentrations (mM for strain MSR33 were: Hg(2+, 0.12 and CH(3Hg(+, 0.08. The addition of Hg(2+ (0.04 mM at exponential phase had not an effect on the growth rate of strain MSR33. In contrast, after Hg(2+ addition at exponential phase the parental strain CH34 showed an immediate cessation of cell growth. During exposure to Hg(2+ no effects in the morphology of MSR33 cells were observed, whereas CH34 cells exposed to Hg(2+ showed a fuzzy outer membrane. Bioremediation with strain MSR33 of two mercury-contaminated aqueous solutions was evaluated. Hg(2+ (0.10 and 0.15 mM was completely volatilized by strain MSR33 from the polluted waters in presence of thioglycolate (5 mM after 2 h. CONCLUSIONS/SIGNIFICANCE: A broad-spectrum mercury-resistant strain MSR33 was generated by incorporation of plasmid pTP6 that was directly isolated from the environment into C. metallidurans CH34. Strain MSR33 is capable to remove mercury from polluted waters. This is the first study to use an IncP-1β plasmid directly isolated from the environment, to generate a novel

Bacterial flora and antibiotic resistance from eggs of green turtles Chelonia mydas: An indication of polluted effluents

International Nuclear Information System (INIS)

Al-Bahry, Saif; Mahmoud, Ibrahim; Elshafie, Abdulkader; Al-Harthy, Asila; Al-Ghafri, Sabha; Al-Amri, Issa; Alkindi, Abdulaziz

2009-01-01

Sea turtles migrate to various habitats where they can be exposed to different pollutants. Bacteria were collected from turtle eggs and their resistance to antibiotics was used as pollutant bio-indicators of contaminated effluents. Eggs were collected randomly from turtles when they were laying their eggs. A total of 90 eggs were collected and placed into sterile plastic bags (3 eggs/turtle) during June-December of 2003. The bacteria located in the eggshell, albumen and yolk were examined, and 42% of the eggs were contaminated with 10 genera of bacteria. Pseudomonas spp. were the most frequent isolates. The albumen was found to be the part of the egg to be the least contaminated by bacterial infection. Bacterial isolates tested with 14 antibiotics showed variations in resistance. Resistance to ampicillin was the highest. The presence of antibiotic resistant bacteria in eggs indicates that the green turtle populations were subjected to polluted effluents during some of their migratory routes and feeding habitats. Scanning electron microscopy revealed that Salmonella typhimurium penetrated all eggshell layers.

Development of RadRob15, A Robot for Detecting Radioactive Contamination in Nuclear Medicine Departments

Directory of Open Access Journals (Sweden)

Shafe A.

2016-09-01

Full Text Available Accidental or intentional release of radioactive materials into the living or working environment may cause radioactive contamination. In nuclear medicine departments, radioactive contamination is usually due to radionuclides which emit high energy gamma photons and particles. These radionuclides have a broad range of energies and penetration capabilities. Rapid detection of radioactive contamination is very important for efficient removing of the contamination without spreading the radionuclides. A quick scan of the contaminated area helps health physicists locate the contaminated area and assess the level of activity. Studies performed in IR Iran shows that in some nuclear medicine departments, areas with relatively high levels of activity can be found. The highest contamination level was detected in corridors which are usually used by patients. To monitor radioactive contamination in nuclear medicine departments, RadRob15, a contamination detecting robot was developed in the Ionizing and Non-ionizing Radiation Protection Research Center (INIRPRC. The motor vehicle scanner and the gas radiation detector are the main components of this robot. The detection limit of this robot has enabled it to detect low levels of radioactive contamination. Our preliminary tests show that RadRob15 can be easily used in nuclear medicine departments as a device for quick surveys which identifies the presence or absence of radioactive contamination.

Seawater is a reservoir of multi-resistant Escherichia coli, including strains hosting plasmid-mediated quinolones resistance and extended-spectrum beta-lactamases genes.

Science.gov (United States)

Alves, Marta S; Pereira, Anabela; Araújo, Susana M; Castro, Bruno B; Correia, António C M; Henriques, Isabel

2014-01-01

The aim of this study was to examine antibiotic resistance (AR) dissemination in coastal water, considering the contribution of different sources of fecal contamination. Samples were collected in Berlenga, an uninhabited island classified as Natural Reserve and visited by tourists for aquatic recreational activities. To achieve our aim, AR in Escherichia coli isolates from coastal water was compared to AR in isolates from two sources of fecal contamination: human-derived sewage and seagull feces. Isolation of E. coli was done on Chromocult agar. Based on genetic typing 414 strains were established. Distribution of E. coli phylogenetic groups was similar among isolates of all sources. Resistances to streptomycin, tetracycline, cephalothin, and amoxicillin were the most frequent. Higher rates of AR were found among seawater and feces isolates, except for last-line antibiotics used in human medicine. Multi-resistance rates in isolates from sewage and seagull feces (29 and 32%) were lower than in isolates from seawater (39%). Seawater AR profiles were similar to those from seagull feces and differed significantly from sewage AR profiles. Nucleotide sequences matching resistance genes bla TEM, sul1, sul2, tet(A), and tet(B), were present in isolates of all sources. Genes conferring resistance to 3rd generation cephalosporins were detected in seawater (bla CTX-M-1 and bla SHV-12) and seagull feces (bla CMY-2). Plasmid-mediated determinants of resistance to quinolones were found: qnrS1 in all sources and qnrB19 in seawater and seagull feces. Our results show that seawater is a relevant reservoir of AR and that seagulls are an efficient vehicle to spread human-associated bacteria and resistance genes. The E. coli resistome recaptured from Berlenga coastal water was mainly modulated by seagulls-derived fecal pollution. The repertoire of resistance genes covers antibiotics critically important for humans, a potential risk for human health.

Seawater is a reservoir of multi-resistant Escherichia coli, including strains hosting plasmid-mediated quinolones resistance and extended-spectrum beta-lactamases genes

Directory of Open Access Journals (Sweden)

Marta S. Alves

2014-08-01

Full Text Available The aim of this study was to examine antibiotic resistance (AR dissemination in coastal water, considering the contribution of different sources of faecal contamination. Samples were collected in Berlenga, an uninhabited island classified as Natural Reserve and visited by tourists for aquatic recreational activities. To achieve our aim, AR in Escherichia coli isolates from coastal water was compared to AR in isolates from two sources of faecal contamination: human-derived sewage and seagull faeces. Isolation of E. coli was done on Chromocult agar. Based on genetic typing 414 strains were established. Distribution of E. coli phylogenetic groups was similar among isolates of all sources. Resistances to streptomycin, tetracycline, cephalothin and amoxicillin were the most frequent. Higher rates of AR were found among seawater and faeces isolates, except for last-line antibiotics used in human medicine. Multi-resistance rates in isolates from sewage and seagull faeces (29% and 32% were lower than in isolates from seawater (39%. Seawater AR profiles were similar to those from seagull faeces and differed significantly from sewage AR profiles. Nucleotide sequences matching resistance genes blaTEM, sul1, sul2, tet(A and tet(B, were present in isolates of all sources. Genes conferring resistance to 3rd generation cephalosporins were detected in seawater (blaCTX-M-1 and blaSHV-12 and seagull faeces (blaCMY-2. Plasmid-mediated determinants of resistance to quinolones were found: qnrS1 in all sources and qnrB19 in seawater and seagull faeces. Our results show that seawater is a relevant reservoir of AR and that seagulls are an efficient vehicle to spread human-associated bacteria and resistance genes. The E. coli resistome recaptured from Berlenga coastal water was mainly modulated by seagulls-derived faecal pollution. The repertoire of resistance genes covers antibiotics critically important for humans, a potential risk for human health.

Aerosol Delivery for Amendment Distribution in Contaminated Vadose Zones

Science.gov (United States)

Hall, R. J.; Murdoch, L.; Riha, B.; Looney, B.

2011-12-01

Remediation of contaminated vadose zones is often hindered by an inability to effectively distribute amendments. Many amendment-based approaches have been successful in saturated formations, however, have not been widely pursued when treating contaminated unsaturated materials due to amendment distribution limitations. Aerosol delivery is a promising new approach for distributing amendments in contaminated vadose zones. Amendments are aerosolized and injected through well screens. During injection the aerosol particles are transported with the gas and deposited on the surfaces of soil grains. Resulting distributions are radially and vertically broad, which could not be achieved by injecting pure liquid-phase solutions. The objectives of this work were A) to characterize transport and deposition behaviors of aerosols; and B) to develop capabilities for predicting results of aerosol injection scenarios. Aerosol transport and deposition processes were investigated by conducting lab-scale injection experiments. These experiments involved injection of aerosols through a 2m radius, sand-filled wedge. A particle analyzer was used to measure aerosol particle distributions with time, and sand samples were taken for amendment content analysis. Predictive capabilities were obtained by constructing a numerical model capable of simulating aerosol transport and deposition in porous media. Results from tests involving vegetable oil aerosol injection show that liquid contents appropriate for remedial applications could be readily achieved throughout the sand-filled wedge. Lab-scale tests conducted with aqueous aerosols show that liquid accumulation only occurs near the point of injection. Tests were also conducted using 200 g/L salt water as the aerosolized liquid. Liquid accumulations observed during salt water tests were minimal and similar to aqueous aerosol results. However, particles were measured, and salt deposited distal to the point of injection. Differences between

Prevalence of Antibiotic Resistance in Escherichia coli Isolated from Poultry Meat Supply in Isfahan

Directory of Open Access Journals (Sweden)

Farhad Safarpordehkordi

2014-08-01

Conclusions: Despite the high contamination rate of chicken meat with Escherichia coli, majority of isolates had high resistance to common antibiotics. Complete cooking of meat and avoid indiscriminate prescribing of antibiotics, preventing the occurrence of food poisoning due to resistant Escherichia coli.

Multidrug-resistant pathogens in the food supply.

Science.gov (United States)

Doyle, Marjorie E

2015-04-01

Antimicrobial resistance, including multidrug resistance (MDR), is an increasing problem globally. MDR bacteria are frequently detected in humans and animals from both more- and less-developed countries and pose a serious concern for human health. Infections caused by MDR microbes may increase morbidity and mortality and require use of expensive drugs and prolonged hospitalization. Humans may be exposed to MDR pathogens through exposure to environments at health-care facilities and farms, livestock and companion animals, human food, and exposure to other individuals carrying MDR microbes. The Centers for Disease Control and Prevention classifies drug-resistant foodborne bacteria, including Campylobacter, Salmonella Typhi, nontyphoidal salmonellae, and Shigella, as serious threats. MDR bacteria have been detected in both meat and fresh produce. Salmonellae carrying genes coding for resistance to multiple antibiotics have caused numerous foodborne MDR outbreaks. While there is some level of resistance to antimicrobials in environmental bacteria, the widespread use of antibiotics in medicine and agriculture has driven the selection of a great variety of microbes with resistance to multiple antimicrobials. MDR bacteria on meat may have originated in veterinary health-care settings or on farms where animals are given antibiotics in feed or to treat infections. Fresh produce may be contaminated by irrigation or wash water containing MDR bacteria. Livestock, fruits, and vegetables may also be contaminated by food handlers, farmers, and animal caretakers who carry MDR bacteria. All potential sources of MDR bacteria should be considered and strategies devised to reduce their presence in foods. Surveillance studies have documented increasing trends in MDR in many pathogens, although there are a few reports of the decline of certain multidrug pathogens. Better coordination of surveillance programs and strategies for controlling use of antimicrobials need to be implemented in

Determination of phosphorus contamination during antimony implantation by measurement and simulation

International Nuclear Information System (INIS)

Kuruc, M.; Hulenyi, L.; Kinder, R.

2006-01-01

Experimental determination of phosphorus cross-contamination during antimony implantation is presented. As a suitable structure for this experiment, a buried layer was employed which is created by implanting antimony followed by a long diffusion process. The samples implanted in different implanters were analysed by secondary ion mass spectrometry (SIMS), four-point probe and spreading resistance methods. The obtained results were compared with those calculated by program SUPREM-IV. Methods that can and cannot be used to determine phosphorus contamination during antimony implantation and to estimate the fluence of phosphorus being co-implanted with antimony are described in detail

Measurement of air contamination in different wards of public sector hospital, Sukkur.

Science.gov (United States)

Memon, Badaruddin AllahDino; Bhutto, Gul Hassan; Rizvi, Wajid Hussain

2016-11-01

The aim of this study was to evaluate and assess the index of bacterial contamination in different wards of the Public Sector Hospital of Sukkur (Teaching) Pakistan; whether or not the air contamination was statistically different from the acceptable level using active and passive sampling. In addition to this main hypothesis, other investigations included: occurrence of the most common bacteria, whether or not the bacterial contamination in the wards was a persistent problem and identification of the effective antibiotics against the indentified bacteria. The evidence sought based on the One Sample T test suggests that there is a (statistically) significant difference between the observed (higher) than the acceptance level (pcontamination problem was persistent as there was no significant difference among observed contamination of all three visits at (p>0.01) and the result of antibiotic susceptibility test highlights sensitivity and resistance level of antibiotics for the indentified bacteria.

Capability Paternalism

NARCIS (Netherlands)

Claassen, R.J.G.|info:eu-repo/dai/nl/269266224

A capability approach prescribes paternalist government actions to the extent that it requires the promotion of specific functionings, instead of the corresponding capabilities. Capability theorists have argued that their theories do not have much of these paternalist implications, since promoting

Design of online testing system of material radiation resistance

International Nuclear Information System (INIS)

Wan Junsheng; He Shengping; Gao Xinjun

2014-01-01

The capability of radiation resistance is important for some material used in some specifically engineering fields. It is the same principal applied in all existing test system that compares the performance parameter after radiation to evaluate material radiation resistance. A kind of new technique on test system of material radiation resistance is put forward in this paper. Experimentation shows that the online test system for material radiation resistance works well and has an extending application outlook. (authors)

Cross-sectional point prevalence survey to study the environmental contamination of nosocomial pathogens in intensive care units under real-life conditions.

Science.gov (United States)

Wille, I; Mayr, A; Kreidl, P; Brühwasser, C; Hinterberger, G; Fritz, A; Posch, W; Fuchs, S; Obwegeser, A; Orth-Höller, D; Lass-Flörl, C

2018-01-01

In intensive care units (ICUs), inanimate surfaces and equipment may be contaminated by nosocomial pathogens, including multi-drug-resistant micro-organisms. To assess the degree of environmental contamination close to and distant from patients, and contamination of healthcare workers' (HCWs) hands with nosocomial pathogens under real-life conditions and to investigate potential transmission events. Over the course of three weeks, agar contact samples were taken close to and distant from patient areas and from HCWs' hands in eight ICUs of a tertiary care hospital in Innsbruck, Austria. Each ICU was visited once without announcement. Species identification and antimicrobial susceptibility testing were performed according to standard methods, and corresponding strains from patient, environment and hand samples were genotyped using pulsed-field gel electrophoresis. Among 523 samples, HCWs' hands were most frequently contaminated with potentially pathogenic bacteria (15.2%), followed by areas close to patients (10.9%) and areas distant from patients (9.1%). Gram-positive bacteria were identified most often (67.8%), with Enterococcus spp. being the most prevalent species (70% vancomycin sensitive and 30% vancomycin resistant) followed by Staphylococcus aureus, of which 64% were classified as meticillin-resistant Staphylococcus aureus. Molecular typing documented identical strains among patient, environment and hand isolates. This study found widespread contamination of the ICU environment with clinically relevant pathogens, including multi-drug-resistant micro-organisms, despite cleaning and disinfection. The bioburden might not be restricted to areas close to patients. The role of extended environmental disinfection of areas distant from patients in order to improve infection prevention needs further discussion. Copyright © 2017 The Healthcare Infection Society. Published by Elsevier Ltd. All rights reserved.

Identification of anthraquinone-degrading bacteria in soil contaminated with polycyclic aromatic hydrocarbons.

Science.gov (United States)

Rodgers-Vieira, Elyse A; Zhang, Zhenfa; Adrion, Alden C; Gold, Avram; Aitken, Michael D

2015-06-01

Quinones and other oxygenated polycyclic aromatic hydrocarbons (oxy-PAHs) are toxic and/or genotoxic compounds observed to be cocontaminants at PAH-contaminated sites, but their formation and fate in contaminated environmental systems have not been well studied. Anthracene-9,10-dione (anthraquinone) has been found in most PAH-contaminated soils and sediments that have been analyzed for oxy-PAHs. However, little is known about the biodegradation of oxy-PAHs, and no bacterial isolates have been described that are capable of growing on or degrading anthraquinone. PAH-degrading Mycobacterium spp. are the only organisms that have been investigated to date for metabolism of a PAH quinone, 4,5-pyrenequinone. We utilized DNA-based stable-isotope probing (SIP) with [U-(13)C]anthraquinone to identify bacteria associated with anthraquinone degradation in PAH-contaminated soil from a former manufactured-gas plant site both before and after treatment in a laboratory-scale bioreactor. SIP with [U-(13)C]anthracene was also performed to assess whether bacteria capable of growing on anthracene are the same as those identified to grow on anthraquinone. Organisms closely related to Sphingomonas were the most predominant among the organisms associated with anthraquinone degradation in bioreactor-treated soil, while organisms in the genus Phenylobacterium comprised the majority of anthraquinone degraders in the untreated soil. Bacteria associated with anthracene degradation differed from those responsible for anthraquinone degradation. These results suggest that Sphingomonas and Phenylobacterium species are associated with anthraquinone degradation and that anthracene-degrading organisms may not possess mechanisms to grow on anthraquinone. Copyright © 2015, American Society for Microbiology. All Rights Reserved.

Physical therapy clinic therapeutic ultrasound equipment as a source for bacterial contamination.

Science.gov (United States)

Spratt, Henry G; Levine, David; Tillman, Larry

2014-10-01

A procedure commonly used in physical therapy (PT) clinics is therapeutic ultrasound (US). This equipment and associated gel comes in contact with patient skin, potentially serving as a reservoir for bacteria. In this study, we sampled US heads, gel bottle tips and gel from nine outpatient PT clinics in Southeastern Tennessee. Samples were collected using sterile swabs. At the microbiology laboratory, these swabs were used to inoculate mannitol salt agar and CHROM-MRSA agar (for Staphylococcal species) and tryptic soy broth to determine non-specific bacterial contamination. US heads, gel bottle tips and gel had variable levels of contamination. Tips of gel bottles had the highest contamination, with 52.7% positive for non-specific bacterial contamination and 3.6% positive for methicillin-resistant Staphylococcus aureus (MRSA). Contamination of gel by non-specific bacteria was found in 14.5% of bottles sampled. US heads (35.5% of those sampled) had non-specific bacterial contamination, with no MRSA detected. Disinfecting US heads after initial swabbing resulted in removal of 90.9% of non-specific contamination. Gel storage at temperatures below 40 °C was found to encourage the growth of mesophilic bacteria. This study demonstrates the need for better cleaning and storage protocols for US heads and gel bottles in PT clinics.

Capacidad de los laboratorios nacionales de referencia en Latinoamérica para detectar mecanismos de resistencia emergentes Capability of national reference laboratories in Latin America to detect emerging resistance mechanisms

Directory of Open Access Journals (Sweden)

Alejandra Corso

2011-12-01

Control Program in Bacteriology and Antibiotic Resistance (LA-EQAS to detect emerging resistance mechanisms- namely: resistance of enterobacteria to carbapenems due to the presence of Klebsiella pneumoniae carbapenemase (KPC and metallo-beta-lactamase (MBL type IMP, and intermediate resistance of Staphylococcus aureus isolates to vancomycin (vancomycin-intermediate resistant S. aureus-VISA. METHODS: The following three isolates were sent to the 17 participating LA-EQAS laboratories: KPC -producing Klebsiella pneumoniae PAHO-161, IMP-producing Enterobacter cloacae PAHO-166, and S. aureus PAHO-165 with intermediate resistance to vancomycin. Performance of each of the following operations was evaluated: interpretation of sensitivity tests, detection of the resistance mechanism, and assessment of either inhibition halo size (disk diffusion method or minimum inhibitory concentration (MIC. RESULTS: Concordance in the detection of resistance mechanisms was 76.4%, 73.3%, and 66.7% for the K. pneumoniae PAHO-161, E. cloacae PAHO-166, and S. aureus PAHO-165 strains, respectively. Concordance between the inhibition areas observed by the participating laboratories and the ranges established by the coordinating laboratory was acceptable for all three isolates, at 90.8%, 92.8%, and 88.9%, respectively. CONCLUSIONS: Overall concordance in on the detection of KPC, MBL, and VISA resistance mechanisms was 72.1%. We consider the national reference laboratories in Latin America capable of recognizing these emerging resistance mechanisms and expect that maximum levels of concordance will be reached in the future.

Structural evolvement and the capability of resistance to γ-ray irradiation on zircon originating from nyainqentanglha granite

International Nuclear Information System (INIS)

Cui Chunlong; Zhang Dong; Kang Houjun; Wang Xiaoli; Zhou Yulin; Yi Facheng; Lu Xirui; Tang Jingyou

2010-01-01

In order to investigate the structural evolvement and the capability of resistance to γ-ray irradiation on zircon as mothball waste forms of radionuclide, the zircon crystals (11.01±0.24 M) were studied as investigative object, which were collected from nyainqentanglha granite. All the samples were irradiated using a 60 Co y-ray source with 576 kGy doses. Phases, structures and microstructures of the as-gained samples before and after y-ray irradiation were characterized by means of a multi-functional microscope, cathodoluminescence (CL), backscattered electron microprobe (BEM), X-ray diffraction (XRD), Raman spectroscopy (Raman), infrared spectroscopy (IR) and scanning electron microscopy (SEM), and so on. Moreover, the geological backgrounds and chemical compositions of zircons originating from natural rocks were analyzed as well. The results indicated that the as-gained crystals came from magmatic rock which undergone near 11 million years geological evolvement and still contain UO 2 and ThO 2 with the contents of 0.5729 wt%. The alteration of 10 -3 nm magnitude in the crystal cell parameters was measured (of the standard XRD card of zircon). The irradiation on the crystalline samples using γ-ray induced to the alteration of 10 -4 nm magnitude for their crystal cell parameters. The conclusion shows that zircon crystals with a certain amount of UO 2 and ThO 2 have better structural stability for the y-ray irradiation. (authors)

Radioactive food and environment contamination

International Nuclear Information System (INIS)

Yousif, A.M.

2001-01-01

The Food and Environment Control Centre of Abu Dhabi Municipality with the help of IAEA has established facilities for regular monitoring of food and environmental samples for radioactive contamination. The Centre is now capable of measuring gamma, beta as well as alpha activity in different types of samples. The main activities in the area of food monitoring are as follows: General monitoring of food gamma radionuclides in foodstuffs by high resolution gamma spectrometry; Determination of specific gamma radionuclides in foodstuffs by high resolution gamma spectrometry; Radiochemical determination of Sr-90 using liquid scintillation analyzer or by gas flow proportional counter; Measurement of gross alpha activity in drinking water

Phytoremediation of small organic contaminants using transgenic plants

Science.gov (United States)

James, C Andrew; Strand, Stuart E

2010-01-01

The efficacy of transgenic plants in the phytoremediation of small organic contaminants has been investigated. Two principal strategies have been pursued (1) the manipulation of phase I metabolic activity to enhance in planta degradation rates, or to impart novel metabolic activity, and (2) the enhanced secretion of reactive enzymes from roots leading to accelerated ex planta degradation of organic contaminants. A pair of dehalogenase genes from Xanthobacter autotrophicus was expressed in tobacco resulting in the dehalogenation of 1,2-dichloroethane, which was otherwise recalcitrant. A laccase gene from cotton was overexpressed in Arabidopsis thaliana resulting in increased secretory laccase activity and the enhanced resistance to trichlorophenol in soils. Although the results to date are promising, much of the work has been limited to laboratory settings; field demonstrations are needed. PMID:19342219

Mitigation of aflatoxin contamination in maize kernels is related to the metabolic alternation of reactive oxygen and nitrogen species by relative humidity

Science.gov (United States)

Environmental factors have been shown to be linked to exacerbated infection of maize kernels by Aspergillus flavus and subsequent aflatoxin contamination. Kernel resistance to aflatoxin contamination is associated with kernel water content and relative humidity during in vitro assays examining aflat...

Tributyltin-resistant bacteria from estuarine and freshwater sediments.

OpenAIRE

Wuertz, S; Miller, C E; Pfister, R M; Cooney, J J

1991-01-01

Resistance to tributyltin (TBT) was examined in populations from TBT-polluted sediments and nonpolluted sediments from an estuary and from fresh water as well as in pure cultures isolated from those sediments. The 50% effective concentrations (EC50s) for populations were higher at a TBT-polluted freshwater site than at a site without TBT, suggesting that TBT selected for a TBT-resistant population. In contrast, EC50s were significantly lower for populations from a TBT-contaminated estuarine s...

Inventory assessment and determination of properties of dust contamination in the Shelter under-roof space

International Nuclear Information System (INIS)

Bogatov, S.A.

2000-01-01

Experimental results on study of radionuclide contamination of surfaces under the roof of Shelter have been analyzed. Values of 'loose' and fixed fuel contamination densities and aerodynamic diameters of dust particles capable of resuspension are obtained. Long term efficiency of dust suppression system under the Shelter roof has been estimated. On the base of retrospective analysis of the results, fuel dust inventory on the surfaces under the Shelter roof was evaluated. 14 refs., 5 tab., 3 figs

Mutation of environmental mycobacteria to resist silver nanoparticles also confers resistance to a common antibiotic.

Science.gov (United States)

Larimer, Curtis; Islam, Mohammad Shyful; Ojha, Anil; Nettleship, Ian

2014-08-01

Non-tuberculous mycobacteria are a threat to human health, gaining entry to the body through contaminated water systems, where they form persistent biofilms despite extensive attempts at disinfection. Silver is a natural antibacterial agent and in nanoparticle form activity is increased by a high surface area. Silver nanoparticles (AgNPs) have been used as alternative disinfectants in circulating water systems, washing machines and even clothing. However, nanoparticles, like any other antibiotic that has a pervasive durable presence, carry the risk of creating a resistant population. In this study Mycobacterium smegmatis strain mc(2)155 was cultured in AgNP enriched agar such that only a small population survived. Surviving cultures were isolated and re-exposed to AgNPs and AgNO3 and resistance to silver was compared to a negative control. After only a single exposure, mutant M. smegmatis populations were resistant to AgNPs and AgNO3. Further, the silver resistant mutants were exposed to antibiotics to determine if general resistance had been conferred. The minimum inhibitory concentration of isoniazid was four times higher for silver resistant mutants than for strain mc(2)155. However, core resistance was not conferred to other toxic metal ions. The mutants had lower resistance to CuSO4 and ZnSO4 than the mc(2)155 strain.

The Effect of Substrate Contaminates on the Life of Epoxy Coatings Submerged in Sea Water

Science.gov (United States)

1991-03-01

contaminants: coal tar, SovaPon, Mare Island and Aquapon . Aquapon is a clear (unpigmented) polyamide epoxy coating. While Aquapon is not normally used for...pigmented coatings. It was found that the Aquapon and coal tar coatings performed similarly, and blistered to the same extent, at the contamination levels...used in the test program. The Sovapon and Mare Island coatings were slightly more resistive to blistering when compared to Aquapon or coal tar but they

SUPERFUND TREATABILITY CLEARINGHOUSE: FULL SCALE ROTARY KILN INCINERATOR FIELD TRIAL: PHASE I, VERIFICATION TRIAL BURN ON DIOXIN/HERBICIDE ORANGE CONTAMINATED SOIL

Science.gov (United States)

This treatability study reports on the results of one of a series of field trials using various remedial action technologies that may be capable of restoring Herbicide Orange (HO)XDioxin contaminated sites. A full-scale field trial using a rotary kiln incinerator capable of pro...

Biodegradation Capability of Some Bacteria Isolates to Use Lubricant Oil in Vitro

Science.gov (United States)

Ahda, Y.; Azhar, M.; Fitri, L.; Afnida, A.; Adha, G. S.; Alifa, W. N.; Handayani, D.; Putri, D. H.; Irdawati, I.; Chatri, M.

2018-04-01

Our previous study identified three species of bacteria, i.e. Alcaligenes sp., Bacillus spl, and Bacillus sp2 isolated from using lubricant oil-contaminated soil in a Padang’s workshop. However, its ability to degrade hydrocarbon were not known yet. In this extension study, we explore a wider area to find more hydrocarbonoclastic bacteria and examined its capability to degrade hydrocarbon in vitro. Seventeen isolates were characterized its capability using NA + used lubricant oil + tween + neutral red medium. Isolates A1, B2, D1 and D4 shows the high degradation index, whereas isolates A2, A3, A5, D2, B1, B3 and isolates A4, B4, D3 have medium and low degradation index, respectively. These potential hydrocarbonoclastic bacteria need in situ characterization to know their actual activities for bioremediation.

Occurrence and antimicrobial resistance patterns of Listeria monocytogenes isolated from vegetables

OpenAIRE

Byrne,Vanessa de Vasconcelos; Hofer,Ernesto; Vallim,Deyse Christina; Almeida,Rogeria Comastri de Castro

2016-01-01

Abstract Although the consumption of fresh and minimally processed vegetables is considered healthy, outbreaks related to the contamination of these products are frequently reported. Among the food-borne pathogens that contaminate vegetables is Listeria monocytogenes, a ubiquitous organism that exhibits the ability to survive and multiply at refrigerated temperatures. This study aimed to evaluate the occurrence of L. monocytogenes in vegetables as well as the antimicrobial resistance of isola...

In vitro capability of faropenem to select for resistant mutants of Streptococcus pneumoniae and Haemophilus influenzae.

Science.gov (United States)

Kosowska-Shick, Klaudia; Clark, Catherine; Credito, Kim; Dewasse, Bonifacio; Beachel, Linda; Ednie, Lois; Appelbaum, Peter C

2008-02-01

When tested against nine strains of pneumococci and six of Haemophilus influenzae of various resistotypes, faropenem failed to select for resistant mutants after 50 days of consecutive subculture in subinhibitory concentrations. Faropenem also yielded low rates of spontaneous mutations against all organisms of both species. By comparison, resistant clones were obtained with macrolides, ketolides, and quinolones.

Method of electrolytic decontamination of contaminated metal materials for radioactivity

International Nuclear Information System (INIS)

Harada, Yoshio; Ishibashi, Masaru; Matsumoto, Hiroyo.

1985-01-01

Purpose: To electrolytically eliminate radioactive materials from metal materials contaminated with radioactive materials, as well as efficiently remove metal ions leached out in an electrolyte. Method: In the case of anodic dissolution of metal materials contaminated with radioactivity in an electrolyte to eliminate radioactive contaminating materials on the surface of the metal materials, a portion of an electrolytic cell is defined with partition membranes capable of permeating metal ions therethrough. A cathode connected to a different power source is disposed to the inside of the partition membranes and fine particle of metals are suspended and floated in the electrolyte. By supplying an electric current between an insoluble anode disposed outside of the partition membranes and the cathode, metal ions permeating from the outside of the partition membranes are deposited on the fine metal particles. Accordingly, since metal ions in the electrolyte are removed, the electrolyte can always be kept clean. (Yoshihara, H.)

Atmospheric contamination

International Nuclear Information System (INIS)

Gruetter, Juerg

1997-01-01

It is about the levels of contamination in center America, the population's perception on the problem, effects of the atmospheric contamination, effects in the environment, causes of the atmospheric contamination, possibilities to reduce the atmospheric contamination and list of Roeco Swisscontac in atmospheric contamination

Understanding Contamination; Twenty Years of Simulating Radiological Contamination

Energy Technology Data Exchange (ETDEWEB)

Emily Snyder; John Drake; Ryan James

2012-02-01

A wide variety of simulated contamination methods have been developed by researchers to reproducibly test radiological decontamination methods. Some twenty years ago a method of non-radioactive contamination simulation was proposed at the Idaho National Laboratory (INL) that mimicked the character of radioactive cesium and zirconium contamination on stainless steel. It involved baking the contamination into the surface of the stainless steel in order to 'fix' it into a tenacious, tightly bound oxide layer. This type of contamination was particularly applicable to nuclear processing facilities (and nuclear reactors) where oxide growth and exchange of radioactive materials within the oxide layer became the predominant model for material/contaminant interaction. Additional simulation methods and their empirically derived basis (from a nuclear fuel reprocessing facility) are discussed. In the last ten years the INL, working with the Defense Advanced Research Projects Agency (DARPA) and the National Homeland Security Research Center (NHSRC), has continued to develop contamination simulation methodologies. The most notable of these newer methodologies was developed to compare the efficacy of different decontamination technologies against radiological dispersal device (RDD, 'dirty bomb') type of contamination. There are many different scenarios for how RDD contamination may be spread, but the most commonly used one at the INL involves the dispersal of an aqueous solution containing radioactive Cs-137. This method was chosen during the DARPA projects and has continued through the NHSRC series of decontamination trials and also gives a tenacious 'fixed' contamination. Much has been learned about the interaction of cesium contamination with building materials, particularly concrete, throughout these tests. The effects of porosity, cation-exchange capacity of the material and the amount of dirt and debris on the surface are very important factors

Influence of inorganic acid pickling on the corrosion resistance of magnesium alloy AZ31 sheet

DEFF Research Database (Denmark)

Nwaogu, Ugochukwu Chibuzoh; Blawert, C.; Scharnagl, N.

2009-01-01

Surface contaminants as a result of thermo-mechanical processing of magnesium alloys, e.g. sheet rolling, can have a negative effect on the corrosion resistance of magnesium alloys. Especially contaminants such as Fe, Ni and Cu, left on the surface of magnesium alloys result in the formation...... of micro-galvanic couples and can therefore increase corrosion attack on these alloys. Due to this influence they should be removed to obtain good corrosion resistance. In this study, the effect of inorganic acid pickling on the corrosion behaviour of a commercial AZ31 magnesium alloy sheet...... cleaning the AZ31 sheet. However, to obtain reasonable corrosion resistance at least 5 mu m of the surface of AZ31 magnesium alloy sheet have to be removed....

Human health risks associated with antimicrobial-resistant enterococci and Staphylococcus aureus on poultry meat

DEFF Research Database (Denmark)

Bortolaia, V.; Gongora, Carmen Espinosa; Guardabassi, L.

2016-01-01

health risks associated with the occurrence of these opportunistic human pathogens on poultry meat with particular focus on the risk of food-borne transmission of antimicrobial resistance. In the absence of conclusive evidence of transmission, this risk was inferred using data from scientific articles......-resistant S. aureus of livestock origin has been reported on poultry meat. In theory handling or ingestion of contaminated meat is a potential risk factor for colonization by methicillin-resistant S. aureus. However, this risk is presently regarded as negligible by public health authorities. Clinical......Enterococci and staphylococci are frequent contaminants on poultry meat. Enterococcus faecalis, Enterococcus faecium and Staphylococcus aureus are also well-known aetiological agents of a wide variety of infections resulting in major healthcare costs. This review provides an overview of the human...

Bio-mechanical removing of contaminated soils: a field experiment

International Nuclear Information System (INIS)

Jouve, A.; Maubert, H.; Schulte, E.

1992-01-01

If, in spite of safety precautions, a major nuclear accident would occur, countermeasures should be taken to attenuate the impact of radioactive deposits. The European RESSAC program (REhabilitation of Soils and Surfaces after an ACcident) aims at studying actions for normal life return in contaminated zones. One of them, called the Decontaminating Vegetal Network (D.V.N.) associates the biological action of turfing plants, producing a dense root-network capable to trap the top contaminated soil particles, and the mechanical efficiency of a turf harvester which can remove only 1 cm of soil. This performance, not associated with other techniques of soil removal such as scrapers or bulldozers, leads to minimize the waste production. The D.V.N is a vegetal cover spread over the contaminated soil, using the hydro-seeding technique. The growing plants are forming a pleasant lawn which may have a positive impact on the public opinion compared to techniques using bitumen mixtures to cover the soil. Field experiments involving labelling solutions of stable molybdenum salts simulating the contamination of the soil have shown that this technique can be applied as well on homogeneous cultivated soil surfaces as on roughly ploughed soils. 4 refs., 3 figs., 2 tabs

Dynamic capabilities, Marketing Capability and Organizational Performance

Directory of Open Access Journals (Sweden)

Adriana Roseli Wünsch Takahashi

2017-01-01

Full Text Available The goal of the study is to investigate the influence of dynamic capabilities on organizational performance and the role of marketing capabilities as a mediator in this relationship in the context of private HEIs in Brazil. As a research method we carried out a survey with 316 IES and data analysis was operationalized with the technique of structural equation modeling. The results indicate that the dynamic capabilities have influence on organizational performance only when mediated by marketing ability. The marketing capability has an important role in the survival, growth and renewal on educational services offerings for HEIs in private sector, and consequently in organizational performance. It is also demonstrated that mediated relationship is more intense for HEI with up to 3,000 students and other organizational profile variables such as amount of courses, the constitution, the type of institution and type of education do not significantly alter the results.

Physiological and genetics studies of highly radiation-resistant bacteria

International Nuclear Information System (INIS)

Keller, L.C.

1981-01-01

The phenomenon of radiation resistance was studied using micrococci and Moraxella-Acinetobacter capable of surviving very high doses of gamma radiation which were isolated from foods. Physiological age, or growth phase, was found to be an important factor in making comparisons of radiation-resistance among different bacteria and their mutants. Radiation-resistant bacteria were highly resistant to the lethal effect of nitrosoguanidine used for mutagenesis. Studies of relative resistance of radiation-resistant bacteria, radiation-sensitive mutants, and nonradiation-resistant bacteria to killing by different chemical mutagens did not reveal a correlation between the traits of radiation resistance and mutagen resistance among different strains. Comparisons of plasmid profiles of radiation-resistant bacteria and selected radiation-sensitive mutants suggested the possibility that plasmids may carry genes involved in radiation resistance

Inhibition of cellular efflux pumps involved in multi xenobiotic resistance (MXR) in echinoid larvae as a possible mode of action for increased ecotoxicological risk of mixtures

NARCIS (Netherlands)

Drs Anselmo, H.M.R.; Berg, van den J.H.J.; Rietjens, I.; Murk, A.J.

2012-01-01

In marine organisms the multi xenobiotic resistance (MXR) mechanism via e.g. P-glycoprotein (P-gp) and multidrug resistance-associated protein (MRP) is an important first line of defense against contaminants by pumping contaminants out of the cells. If compounds would impair the MXR mechanism, this

ACTIVE CAPPING TECHNOLOGY - NEW APPROACHES FOR IN SITU REMEDIATION OF CONTAMINATED SEDIMENTS

Energy Technology Data Exchange (ETDEWEB)

Knox, A.; Paller, M.; Roberts, J.

2012-02-13

This study evaluated pilot-scale active caps composed of apatite, organoclay, biopolymers, and sand for the remediation of metal-contaminated sediments. The active caps were constructed in Steel Creek, at the Savannah River Site near Aiken, South Carolina. Monitoring was conducted for 12 months. Effectiveness of the caps was based on an evaluation of contaminant bioavailability, resistance to erosion, and impacts on benthic organisms. Active caps lowered metal bioavailability in the sediment during the one-year test period. Biopolymers reduced sediment suspension during cap construction, increased the pool of carbon, and lowered the release of metals. This field validation showed that active caps can effectively treat contaminants by changing their speciation, and that caps can be constructed to include more than one type of amendment to achieve multiple goals.

Detection of Antibiotic Resistant Staphylococcus aureus from Milk: A Public Health Implication

Science.gov (United States)

Akindolire, Muyiwa Ajoke; Babalola, Olubukola Oluranti; Ateba, Collins Njie

2015-01-01

The aim of this study was to investigate the occurrence, antibiotic susceptibility profiles, and virulence genes determinants of S. aureus isolated from milk obtained from retail outlets of the North-West Province, South Africa. To achieve this, 200 samples of raw, bulk and pasteurised milk were obtained randomly from supermarkets, shops and some farms in the North-West Province between May 2012 and April 2013. S. aureus was isolated and positively identified using morphological (Gram staining), biochemical (DNase, catalase, haemolysis and rapid slide agglutination) tests, protein profile analysis (MALDI-TOF mass spectrometry) and molecular (nuc specific PCR) methods. The antimicrobial resistance profiles of the isolates were determined using the phenotypic agar diffusion method. Genes encoding enterotoxins, exfoliative toxins and collagen adhesins were also screened using PCR. Among all the samples examined, 30 of 40 raw milk samples (75%), 25 of 85 bulk milk samples (29%) and 10 of 75 pasteurised milk samples (13%) were positive for S. aureus. One hundred and fifty-six PCR-confirmed S. aureus isolates were obtained from 75 contaminated milk samples. A large proportion (60%–100%) of the isolates was resistant to penicillin G, ampicillin, oxacillin, vancomycin, teicoplanin and erythromycin. On the contrary, low level resistance (8.3%–40%) was observed for gentamicin, kanamycin and sulphamethoxazole. Methicillin resistance was detected in 59% of the multidrug resistant isolates and this was a cause for concern. However, only a small proportion (20.6%) of these isolates possessed PBP2a which codes for Methicillin resistance in S. aureus. In addition, 32.7% of isolates possessed the sec gene whereas the sea, seb sed, see, cna, eta, etb genes were not detected. The findings of this study showed that raw, bulk and pasteurised milk in the North-West Province is contaminated with toxigenic and multi-drug resistant S. aureus strains. There is a need to implement

Limitations of sorption isotherms on modeling groundwater contaminant transport

International Nuclear Information System (INIS)

Silva, Eduardo Figueira da

2007-01-01

Design and safety assessment of radioactive waste repositories, as well as remediation of radionuclide contaminated groundwater require the development of models capable of accurately predicting trace element fate and transport. Adsorption of trace radionuclides onto soils and groundwater is an important mechanism controlling near- and far- field transport. Although surface complexation models (SCMs) can better describe the adsorption mechanisms of most radionuclides onto mineral surfaces by directly accounting for variability of system properties and mineral surface properties, isotherms are still used to model contaminant transport in groundwater, despite the much higher system dependence. The present work investigates differences between transport model results based on these two approaches for adsorption modeling. A finite element transport model is used for the isotherm model, whereas the computer program PHREEQC is used for the SCM approach. Both models are calibrated for a batch experiment, and one-dimensional transport is simulated using the calibrated parameters. At the lower injected concentrations there are large discrepancies between SCM and isotherm transport predictions, with the SCM presenting much longer tails on the breakthrough curves. Isotherms may also provide non-conservative results for time to breakthrough and for maximum concentration in a contamination plume. Isotherm models are shown not to be robust enough to predict transport behavior of some trace elements, thus discouraging their use. The results also illustrate the promise of the SCM modeling approach in safety assessment and environmental remediation applications, also suggesting that independent batch sorption measurements can be used, within the framework of the SCM, to produce a more versatile and realistic groundwater transport model for radionuclides which is capable of accounting more accurately for temporal and spatial variations in geochemical conditions. (author)

Staphylococcus aureus in Some Brazilian Dairy Industries: Changes of Contamination and Diversity

DEFF Research Database (Denmark)

Dittmann, Karen Kiesbye; Chaul, Luiza T.; Lee, Sarah H. I.

2017-01-01

Staphylococcus aureus, a major food-poisoning pathogen, is a common contaminant in dairy industries worldwide, including in Brazil. We determined the occurrence of S. aureus in five dairies in Brazil over 8 months. Of 421 samples, 31 (7.4%) were positive for S. aureus and prevalence varied from 0.......8% of strains being sensitive to all antibiotic classes and no Methicillin-resistant S. aureus (MRSA) strains were found. The enterotoxin-encoding genes involved in food-poisoning, e.g., sea, sed, see, and seg were targeted by PCR. The two toxin-encoding genes, sed and see, were not detected. Only three strains...... contamination....

Effects of Lactobacillus delbrueckii on immune response, disease resistance against Aeromonas hydrophila, antioxidant capability and growth performance of Cyprinus carpio Huanghe var.

Science.gov (United States)

Zhang, Chun-Nuan; Zhang, Ji-Liang; Guan, Wen-Chao; Zhang, Xiao-Fei; Guan, Su-Hua; Zeng, Qing-Hui; Cheng, Gao-Feng; Cui, Wei

2017-09-01

The aim of the present study was to investigate effects of dietary Lactobacillus delbrueckii (L. delbrueckii) on immune response, disease resistance against Aeromonas hydrophila (A. hydrophila), antioxidant capability and growth performance of Cyprinus carpio Huanghe var. 450 fish (mean weight of 1.05 ± 0.03 g) were randomly distributed into five groups that fed diets containing different levels of L. delbrueckii (0, 1 × 10 5 , 1 × 10 6 , 1 × 10 7 and 1 × 10 8  CFU g -1 ) for 8 weeks. The results showed that intestinal immune parameters such as lysozyme, acid phosphatase, and myeloperoxidase activities, immunoglobulin M content, and the survival rate were improved in fish fed with 1 × 10 6 and 1 × 10 7  CFU g -1 L. delbrueckii. In addition, 1 × 10 7  CFU g -1 L. delbrueckii supplementation down-regulated mRNA levels of TNF-α, IL-8, IL-1β and NF-κBp65, and up-regulated IL-10 and TGF-β mRNA levels in the intestine. The survival rate was significantly (P < 0.05) higher (68.33%) in fish fed 1 × 10 6  CFU g -1 L. delbrueckii than the control diet-fed group (40%) after challenge by A. hydrophila. Fish fed with diet containing 1 × 10 6  CFU g -1 L. delbrueckii showed higher antioxidant enzyme activities such as superoxide dismutase (SOD), catalase (CAT), glutathione peroxidase (GPX), and total antioxidant capacity (T-AOC) and lower MDA concentrations than those of the control group (P < 0.05). The relative gene expression (SOD, CAT, GPX) showed the same trend with their activities. In addition, the growth performance was significantly improved in fish fed with the diet containing 1 × 10 6 and 1 × 10 7  CFU g -1 L. delbrueckii (P < 0.05). These results demonstrated that dietary optimal levels of L. delbrueckii enhanced immunity, disease resistance against A. hydrophila antioxidant capability and growth performance in Cyprinus carpio Huanghe var. Copyright © 2017 Elsevier Ltd. All rights reserved.

Sandia Laboratories technical capabilities. Auxiliary capabilities: environmental health information science

International Nuclear Information System (INIS)

1975-09-01

Sandia Laboratories is an engineering laboratory in which research, development, testing, and evaluation capabilities are integrated by program management for the generation of advanced designs. In fulfilling its primary responsibility to ERDA, Sandia Laboratories has acquired extensive research and development capabilities. The purpose of this series of documents is to catalog the many technical capabilities of the Laboratories. After the listing of capabilities, supporting information is provided in the form of highlights, which show applications. This document deals with auxiliary capabilities, in particular, environmental health and information science. (11 figures, 1 table) (RWR)

Assessment of Gamma Radiation Resistance of Spores Isolated from the Spacecraft Assembly Facility During MSL Assembly

Science.gov (United States)

Chopra, Arsh; Ramirez, Gustavo A.; Vaishampayan, Parag A.; Venkateswaran, Kasthuri J.

2011-01-01

Spore forming bacteria, a common inhabitant of spacecraft assembly facilities, are known to tolerate extreme environmental conditions such as radiation, desiccation, and high temperatures. Since the Viking era (early 1970's), spores have been utilized to assess the degree and level of microbiological contamination on spacecraft and their associated spacecraft assembly facilities. There is a growing concern that desiccation and extreme radiation resistant spore forming microorganisms associated with spacecraft surfaces can withstand space environmental conditions and subsequently proliferate on another solar body. Such forward contamination would certainly jeopardize future life detection or sample return technologies. It is important to recognize that different classes of organisms are critical while calculating the probability of contamination, and methods must be devised to estimate their abundances. Microorganisms can be categorized based on radiation sensitivity as Type A, B, C, and D. Type C represents spores resistant to radiation (10% or greater survival above 0.8 Mrad gamma radiation). To address these questions we have purified 96 spore formers, isolated during planetary protection efforts of Mars Science Laboratory assembly for gamma radiation resistance. The spores purified and stored will be used to generate data that can be used further to model and predict the probability of forward contamination.

High prevalence of methicillin-resistant coagulase-negative staphylococci isolated from a university environment in Thailand.

Science.gov (United States)

Seng, Rathanin; Leungtongkam, Udomluk; Thummeepak, Rapee; Chatdumrong, Wassana; Sitthisak, Sutthirat

2017-06-01

The present study was conducted to isolate and characterize the molecular epidemiology of the methicillin-resistant staphylococci in the general university environment, where all five locations; the library, restrooms, canteens, computer rooms and outdoor surfaces, are in common use by a large population of students. We used Mannitol Salt Agar (MSA) supplemented with 4 μg/ml of oxacillin to screen the methicillin-resistant staphylococci. The species level was identified by PCR of rdr (Staphylococcus epidermidis), groESL (Staphylococcus haemolyticus) and nuc (Staphylococcus aureus and Staphylococcus warneri) genes and DNA sequencing of tuf and dnaJ genes. The susceptibility patterns of the isolates were determined using the disk diffusion method. Antibiotic and disinfectant resistance genes, together with SCCmec types, were detected by the PCR method. The methicillin resistant-staphylococci were isolated from 41 of 200 samples (20.5%), and all of them were found to be methicillin-resistant coagulase negative staphylococci (MR-CoNS). The library had the highest percentage of contamination, with 43.3% of the samples found to be contaminated. All isolates belonged to 6 different species including S. haemolyticus, S. epidermidis, S. warneri, S. cohnii, S. saprophyticus and S. hominis. The antimicrobial resistance rates were highest against penicillin (100%), then cefoxitin (73.1%), erythromycin (73.1%) and oxacillin (68.3%). Altogether, the isolates were approximately 61.0% multidrug resistant (MDR), with the S. epidermidis isolates being the most multidrug resistant. The prevalence of the qacA/B gene was detected in 63.4% of the isolates, and SCCmec could be typed in 43.9% (18/41) of the isolates. The type range was: II (n = 1), IVd (n = 1), I (n = 2), V (n = 6), IVa (n = 8) and untypeable (n = 23). This result indicates that these university environments are contaminated with methicillin-resistant coagulase negative staphylococci that carry various SCCmec types and

Human health hazard from antimicrobial-resistant enterococci in animals and food

DEFF Research Database (Denmark)

Heuer, Ole Eske; Hammerum, Anette Marie; Collignon, P.

2006-01-01

The use of antimicrobial agents in the modern farm industry has created a reservoir of resistant bacteria in food animals. Foods of animal origin are often contaminated with enterococci that are likely to contribute resistance genes, virulence factors, or other properties to enterococci IN humans....... The potential hazard to human health from antimicrobial-resistant enterococci in animals is questioned by some scientists because of evidence of host specificity of enterococci. Similarly, the occurrences of specific nosocomial clones of enterococci in hospitals have lead to the misconception that antimicrobial-resistant...... to change the current view that antimicrobial-resistant enterococci from animals pose a threat to human health. On the contrary, antimicrobial resistance genes appear to spread freely between enterococci from different reservoirs, irrespective of their apparent host association....

Endophytic bacteria improve phytoremediation of Ni and TCE co-contamination

International Nuclear Information System (INIS)

Weyens, Nele; Croes, Sarah; Dupae, Joke; Newman, Lee; Lelie, Daniel van der; Carleer, Robert; Vangronsveld, Jaco

2010-01-01

The aim of this work was to investigate if engineered endophytes can improve phytoremediation of co-contaminations by organic pollutants and toxic metals. As a model system, yellow lupine was inoculated with the endophyte Burkholderia cepacia VM1468 possessing (a) the pTOM-Bu61 plasmid, coding for constitutive trichloroethylene (TCE) degradation, and (b) the ncc-nre Ni resistance/sequestration system. Plants were exposed to Ni and TCE and (a) Ni and TCE phytotoxicity, (b) TCE degradation and evapotranspiration, and (c) Ni concentrations in the roots and shoots were determined. Inoculation with B. cepacia VM1468 resulted in decreased Ni and TCE phytotoxicity, as measured by 30% increased root biomass and up to 50% decreased activities of enzymes involved in anti-oxidative defence in the roots. In addition, TCE evapotranspiration showed a decreasing trend and a 5 times higher Ni uptake was observed after inoculation. - Engineered endophytes can improve phytoremediation of mixed contaminations via enhanced degradation of organic contaminants and improved metal uptake and translocation.

Bioremediation of hydrocarbon and brine contaminated topsoil : annual report (1992-93)

International Nuclear Information System (INIS)

Danielson, R.M.

1996-01-01

This report presents the results of a study which examined the remediation of hydrocarbon and brine contaminated topsoil in a field-based bioreactor at a gas processing plant in Nevis, Alberta during 1992 and 1993. The hydrocarbon and brine contaminated topsoil was placed in the Bio-Reactor and treated for eleven months. Four treatments were applied to eight Bio-Reactor cells: (1) ambient temperature/no forced aeration, (2) ambient temperature/forced aeration, (3) optimum temperature/no forced aeration and (4) optimum temperature/forced aeration. The ninth cell was filled with 30 cm contaminated topsoil and maintained under optimum temperature/forced aeration. The contaminated topsoil was kept moist throughout the experiment by an automatic irrigation system. The contaminated topsoil in the heated cells lost 40 per cent of its original hydrocarbon content in one year; the soil in the non-heated cells lost between 25 and 29 per cent in the same period. Results showed that the Bio-Reactor offered an inexpensive means for promoting a natural process for degrading organic compounds by microorganisms in soil. Equally important, it is capable of handling the large volumes of waste produced by the oil and gas industry. 64 refs., 35 tabs., 46 figs

Surgery for acquired cardiovascular disease: antiseptic treatment of contaminated vein grafts.

Science.gov (United States)

Schmidt, F P; Peivandi, A A; Kohnen, W; Jansen, B

2014-04-01

Saphenous vein grafts harvested for use as bypass conduits can be contaminated intraoperatively, e.g. by being inadvertently dropped to the floor of the operating room (OR). This study was performed to investigate microorganisms most likely contaminating vein grafts and to assess the possible efficacy of measures to treat potentially contaminated vein grafts antiseptically for further use. In a first step we determined the microbiological flora of the OR using surface cultures and cultures from intentionally dropped vein grafts. Several antiseptic agents (PVP-iodine 10%, octenidinhydrochloride 0.1%, polyhexanide 1%) were evaluated for their in vitro efficacy to disinfect artificially contaminated vein segments. The most promising antiseptic regimen was tested on veins contaminated in a real OR setting. Finally, we tested for possible alterations in mechanical properties of the veins caused by antiseptic treatment. Coagulase-negative staphylococci where the predominant bacteria recovered from the OR with 59.9%. Antiseptic treatment with a combination of octenidine and PVP-iodine resulted in a higher rate of negative cultures than any single agent. Treatment of 50 saphenous vein grafts contaminated in the OR with the combination regimen resulted in only 3 positive cultural results within 7 days. Mechanical tear-stress testing comparing antiseptically treated vein grafts with controls showed no difference in their resistance to tear stress. Antiseptic treatment of contaminated vein grafts was shown to be effective in a high percentage of cases without altering mechanical properties of grafts and may be an option for the surgeon in case of a contamination.

Greenhouse study on the phytoremediation potential of vetiver grass, Chrysopogon zizanioides L., in arsenic-contaminated soils.

Science.gov (United States)

Datta, Rupali; Quispe, Mario A; Sarkar, Dibyendu

2011-01-01

The purpose of this greenhouse study was to assess the capacity of vetiver grass to accumulate arsenic from pesticide-contaminated soils of varying physico-chemical properties. Results indicate that vetiver is capable of tolerating moderate levels of arsenic up to 225 mg/kg. Plant growth and arsenic removal efficiency was strongly influenced by soil properties. Arsenic removal was highest (10.6%) in Millhopper soil contaminated with 45 mg/kg arsenic, which decreased to 4.5 and 0.6% at 225 and 450 mg/kg, respectively. High biomass, widespread root system and environmental tolerance make this plant an attractive choice for the remediation of soils contaminated with moderate levels of arsenic.

High sensitivity detection and characterization of the chemical state of trace element contamination on silicon wafers

CERN Document Server

Pianetta, Piero A; Baur, K; Brennan, S; Homma, T; Kubo, N

2003-01-01

Increasing the speed and complexity of semiconductor integrated circuits requires advanced processes that put extreme constraints on the level of metal contamination allowed on the surfaces of silicon wafers. Such contamination degrades the performance of the ultrathin SiO sub 2 gate dielectrics that form the heart of the individual transistors. Ultimately, reliability and yield are reduced to levels that must be improved before new processes can be put into production. It should be noted that much of this metal contamination occurs during the wet chemical etching and rinsing steps required for the manufacture of integrated circuits and industry is actively developing new processes that have already brought the metal contamination to levels beyond the measurement capabilities of conventional analytical techniques. The measurement of these extremely low contamination levels has required the use of synchrotron radiation total reflection X-ray fluorescence (SR-TXRF) where sensitivities 100 times better than conv...

Characterization of the Rhodococcus sp. MK1 strain and its pilot application for bioremediation of diesel oil-contaminated soil.

Science.gov (United States)

Kis, Ágnes Erdeiné; Laczi, Krisztián; Zsíros, Szilvia; Kós, Péter; Tengölics, Roland; Bounedjoum, Naila; Kovács, Tamás; Rákhely, Gábor; Perei, Katalin

2017-12-01

Petroleum hydrocarbons and derivatives are widespread contaminants in both aquifers and soil, their elimination is in the primary focus of environmental studies. Microorganisms are key components in biological removal of pollutants. Strains capable to utilize hydrocarbons usually appear at the contaminated sites, but their metabolic activities are often restricted by the lack of nutrients and/or they can only utilize one or two components of a mixture. We isolated a novel Rhodococcus sp. MK1 strain capable to degrade the components of diesel oil simultaneously. The draft genome of the strain was determined and besides the chromosome, the presence of one plasmid could be revealed. Numerous routes for oxidation of aliphatic and aromatic compounds were identified. The strain was tested in ex situ applications aiming to compare alternative solutions for microbial degradation of hydrocarbons. The results of bioaugmentation and biostimulation experiments clearly demonstrated that - in certain cases - the indigenous microbial community could be exploited for bioremediation of oil-contaminated soils. Biostimulation seems to be efficient for removal of aged contaminations at lower concentration range, whereas bioaugmentation is necessary for the treatment of freshly and highly polluted sites.

ADVANCED SIMULATION CAPABILITY FOR ENVIRONMENTAL MANAGEMENT- CURRENT STATUS AND PHASE II DEMONSTRATION RESULTS

Energy Technology Data Exchange (ETDEWEB)

Seitz, R.

2013-02-26

The U.S. Department of Energy (USDOE) Office of Environmental Management (EM), Office of Soil and Groundwater, is supporting development of the Advanced Simulation Capability for Environmental Management (ASCEM). ASCEM is a state-of-the-art scientific tool and approach for understanding and predicting contaminant fate and transport in natural and engineered systems. The modular and open source high-performance computing tool facilitates integrated approaches to modeling and site characterization that enable robust and standardized assessments of performance and risk for EM cleanup and closure activities. The ASCEM project continues to make significant progress in development of computer software capabilities with an emphasis on integration of capabilities in FY12. Capability development is occurring for both the Platform and Integrated Toolsets and High-Performance Computing (HPC) Multiprocess Simulator. The Platform capabilities provide the user interface and tools for end-to-end model development, starting with definition of the conceptual model, management of data for model input, model calibration and uncertainty analysis, and processing of model output, including visualization. The HPC capabilities target increased functionality of process model representations, toolsets for interaction with Platform, and verification and model confidence testing. The Platform and HPC capabilities are being tested and evaluated for EM applications in a set of demonstrations as part of Site Applications Thrust Area activities. The Phase I demonstration focusing on individual capabilities of the initial toolsets was completed in 2010. The Phase II demonstration completed in 2012 focused on showcasing integrated ASCEM capabilities. For Phase II, the Hanford Site deep vadose zone (BC Cribs) served as an application site for an end-to-end demonstration of capabilities, with emphasis on integration and linkages between the Platform and HPC components. Other demonstrations

Risk of contamination of nasal sprays in otolaryngologic practice

Directory of Open Access Journals (Sweden)

Akkuzu Babur

2007-03-01

Full Text Available Abstract Background Reusable nasal-spray devices are frequently used in otolaryngologic examinations, and there is an increasing concern about the risk of cross-contamination from these devices. The aim of our study was to determine, by means of microbiologic analysis, the safety of a positive-displacement or pump-type atomizer after multiple uses. Methods A reusable nasal spray bottle, pump, and tips were used in the nasal physical examination of 282 patients admitted to a tertiary otolaryngology clinic. The effectiveness of 2 different methods of prophylaxis against microbiologic contamination (the use of protective punched caps or rinsing the bottle tip with alcohol was compared with that of a control procedure. Results Although there was no statistically significant difference in positive culture rates among the types of nasal spray bottles tested, methicillin-resistant coagulase-negative staphylococci were isolated in 4 of 198 cultures. Conclusion Given these findings, we concluded that additional precautions (such as the use of an autoclave between sprays, disposable tips, or disposable devices are warranted to avoid interpatient cross-contamination from a reusable nasal spray device.

Antibiotic-resistant fecal bacteria, antibiotics, and mercury in surface waters of Oakland County, Michigan, 2005-2006

Science.gov (United States)

Fogarty, Lisa R.; Duris, Joseph W.; Crowley, Suzanne L.; Hardigan, Nicole

2007-01-01

Water samples collected from 20 stream sites in Oakland and Macomb Counties, Mich., were analyzed to learn more about the occurrence of cephalosporin-resistant Escherichia coli (E. coli) and vancomycin-resistant enterococci (VRE) and the co-occurrence of antibiotics and mercury in area streams. Fecal indicator bacteria concentrations exceeded the Michigan recreational water-quality standard of 300 E. coli colony forming units (CFU) per 100 milliliters of water in 19 of 35 stream-water samples collected in Oakland County. A gene commonly associated with enterococci from humans was detected in samples from Paint Creek at Rochester and Evans Ditch at Southfield, indicating that human fecal waste is a possible source of fecal contamination at these sites. E. coli resistant to the cephalosporin antibiotics (cefoxitin and/ or ceftriaxone) were found at all sites on at least one occasion. The highest percentages of E. coli isolates resistant to cefoxitin and ceftriaxone were 71 percent (Clinton River at Auburn Hills) and 19 percent (Sashabaw Creek near Drayton Plains), respectively. Cephalosporin-resistant E. coli was detected more frequently in samples from intensively urbanized or industrialized areas than in samples from less urbanized areas. VRE were not detected in any sample collected in this study. Multiple antibiotics (azithromycin, erythromycin, ofloxacin, sulfamethoxazole, and trimethoprim) were detected in water samples from the Clinton River at Auburn Hills, and tylosin (an antibiotic used in veterinary medicine and livestock production that belongs to the macrolide group, along with erythromycin) was detected in one water sample from Paint Creek at Rochester. Concentrations of total mercury were as high as 19.8 nanograms per liter (Evans Ditch at Southfield). There was no relation among percentage of antibiotic-resistant bacteria and measured concentrations of antibiotics or mercury in the water. Genetic elements capable of exchanging multiple antibiotic-resistance

Diversity of Antimicrobial Resistance and Virulence Determinants in Pseudomonas aeruginosa Associated with Fresh Vegetables

Directory of Open Access Journals (Sweden)

Kashina Allydice-Francis

2012-01-01

Full Text Available With the increased focus on healthy eating and consuming raw vegetables, this study assessed the extent of contamination of fresh vegetables by Pseudomonas aeruginosa in Jamaica and examined the antibiotic susceptibility profiles and the presence of various virulence associated determinants of P. aeruginosa. Analyses indicated that vegetables from retail markets and supermarkets were widely contaminated by P. aeruginosa; produce from markets were more frequently contaminated, but the difference was not significant. Lettuce and carrots were the most frequently contaminated vegetables, while tomatoes were the least. Pigment production (Pyoverdine, pyocyanin, pyomelanin and pyorubin, fluorescein and alginate were common in these isolates. Imipenem, gentamicin and ciprofloxacin were the most inhibitory antimicrobial agents. However, isolates were resistant or showed reduced susceptibility to ampicillin, chloramphenicol, sulphamethoxazole/trimethoprim and aztreonam, and up to 35% of the isolates were resistant to four antimicrobial agents. As many as 30% of the isolates were positive for the fpv1 gene, and 13% had multiple genes. Sixty-four percent of the isolates harboured an exoenzyme gene (exoS, exoT, exoU or exoY, and multiple exo genes were common. We conclude that P. aeruginosa is a major contaminant of fresh vegetables, which might be a source of infection for susceptible persons within the community.

Robustness of a cross contamination model describing transfer of pathogens during grinding of meat

DEFF Research Database (Denmark)

Møller, Cleide Oliveira de Almeida; Sant’Ana, A. S.; Hansen, Solvej Katrine Holm

2016-01-01

This study aimed to evaluate a cross contamination model for its capability of describing transfer of Salmonella spp. and L. monocytogenes during grinding of varying sizes and numbers of pieces of meats in two grinder systems. Data from 19 trials were collected. Three evaluation approaches were...

Capabilities of the Environmental Effects Branch at Marshall Space Flight Cente

Science.gov (United States)

Rogers, Jan; Finckenor, Miria; Nehls, Mary

2016-01-01

The Environmental Effects Branch at the Marshall Space Flight Center supports a myriad array of programs for NASA, DoD, and commercial space including human exploration, advanced space propulsion, improving life on Earth, and the study of the Sun, the Earth, and the solar system. The branch provides testing, evaluation, and qualification of materials for use on external spacecraft surfaces and in contamination-sensitive systems. Space environment capabilities include charged particle radiation, ultraviolet radiation, atomic oxygen, impact, plasma, and thermal vacuum, anchored by flight experiments and analysis of returned space hardware. These environmental components can be combined for solar wind or planetary surface environment studies or to evaluate synergistic effects. The Impact Testing Facility allows simulation of impacts ranging from sand and rain to micrometeoroids and orbital debris in order to evaluate materials and components for flight and ground-based systems. The Contamination Control Team is involved in the evaluation of environmentally-friendly replacements for HCFC-225 for use in propulsion oxygen systems, developing cleaning methods for additively manufactured hardware, and reducing risk for the Space Launch System.

Genetic diversity and antimicrobial resistance of Escherichia coli from human and animal sources uncovers multiple resistances from human sources.

Directory of Open Access Journals (Sweden)

A Mark Ibekwe

Full Text Available Escherichia coli are widely used as indicators of fecal contamination, and in some cases to identify host sources of fecal contamination in surface water. Prevalence, genetic diversity and antimicrobial susceptibility were determined for 600 generic E. coli isolates obtained from surface water and sediment from creeks and channels along the middle Santa Ana River (MSAR watershed of southern California, USA, after a 12 month study. Evaluation of E. coli populations along the creeks and channels showed that E. coli were more prevalent in sediment compared to surface water. E. coli populations were not significantly different (P = 0.05 between urban runoff sources and agricultural sources, however, E. coli genotypes determined by pulsed-field gel electrophoresis (PFGE were less diverse in the agricultural sources than in urban runoff sources. PFGE also showed that E. coli populations in surface water were more diverse than in the sediment, suggesting isolates in sediment may be dominated by clonal populations.Twenty four percent (144 isolates of the 600 isolates exhibited resistance to more than one antimicrobial agent. Most multiple resistances were associated with inputs from urban runoff and involved the antimicrobials rifampicin, tetracycline, and erythromycin. The occurrence of a greater number of E. coli with multiple antibiotic resistances from urban runoff sources than agricultural sources in this watershed provides useful evidence in planning strategies for water quality management and public health protection.

International workshop on scientific bases for decision making after a radioactive contamination of an urban environment. Book of abstracts

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-12-31

This workshop aims to discuss the most important aspects of scientific bases for decision making after a radioactive contamination in urban environment and to identify some scientific, social and economic open questions. Papers explaining in more details the principles of intervention, computational capabilities and measurements after a contamination of urban areas are presented. A review on practical experiences from Chernobyl and Goiania accidents is also included.

International workshop on scientific bases for decision making after a radioactive contamination of an urban environment. Book of abstracts

International Nuclear Information System (INIS)

1994-01-01

This workshop aims to discuss the most important aspects of scientific bases for decision making after a radioactive contamination in urban environment and to identify some scientific, social and economic open questions. Papers explaining in more details the principles of intervention, computational capabilities and measurements after a contamination of urban areas are presented. A review on practical experiences from Chernobyl and Goiania accidents is also included

Capability of Catfish (Clarias gariepinus to Accumulate Hg2+ From Water

Directory of Open Access Journals (Sweden)

Heny Suseno

2015-12-01

Full Text Available Mercury is hazardous contaminant that can be accumulated by aquatic organisms such as fishes, mussels etc. Catfish is one of source of animal protein but it also can accumulate Hg2+ from water that used in aquaculture. Due to less information about capability of catfish to accumulate Hg2+, therefore we studied bioaccumulation of Hg2+ that used biokinetic approach (aqueous uptake-rate, and elimination-rate.  Nuclear application technique was applied in this study by using radiotracer of 203Hg.  A simple kinetic model was then constructed to predict the bioaccumulation capability of   by catfish. The result of experiments were shown that the uptake rate of difference Hg2+ concentration were 79.90 to 101.22 ml.g-1.d-1. Strong correlation between uptake rates with increasing Hg2+concentration. In addition, the elimination rates were range 0.080 – 0.081 day-1. The biology half time (t1/2b of Hg2+ in whole body catfish were 8.50 – 8.63 days.  However, no clear correlation  between elimination rate with increasing concentration of Hg2+. The calculation of Bio Concentration Factor (BCF shown catfish have capability to accumulated Hg maximum 1242.69 time than its concentration in water

Radiation-resistant bacteria and their application to metal and radionuclides bioremediation

International Nuclear Information System (INIS)

Wang Jianlong

2004-01-01

Microorganisms have a number of applications in the nuclear industry, which would benefit from the use of radiation-resistant microorganisms. Environmentally isolated bacteria have shown to be resistant to gamma irradiation up to a dose of 30,000 Gy. It has also been reported that the presence of ionizing radiation may induce radio-resistance in bacteria. Recent demonstrations of the removal and immobilization of inorganic contaminants by microbial transformations, sorption and mineralization show the potential of both natural and engineered microorganisms as bioremedial tools. This review is to provide an overview of the application of radiation-resistant bacteria to decontamination of metal and radionuclide. (authors)

Characterization of contaminated soil and groundwater surrounding an illegal landfill (S. Giuliano, Venice, Italy) by principal component analysis and kriging

International Nuclear Information System (INIS)

Critto, Andrea; Carlon, Claudio; Marcomini, Antonio

2003-01-01

Information on soil and groundwater contamination was used to develop a site conceptual model and to identify exposure scenarios. - The characterization of a hydrologically complex contaminated site bordering the lagoon of Venice (Italy) was undertaken by investigating soils and groundwaters affected by the chemical contaminants originated by the wastes dumped into an illegal landfill. Statistical tools such as principal components analysis and geostatistical techniques were applied to obtain the spatial distribution of chemical contaminants. Dissolved organic carbon (DOC), SO 4 2- and Cl - were used to trace the migration of the contaminants from the top soil to the underlying groundwaters. The chemical and hydrogeological available information was assembled to obtain the schematic of the conceptual model of the contaminated site capable to support the formulation of major exposure scenarios, which are also provided

A Space Experiment to Measure the Atomic Oxygen Erosion of Polymers and Demonstrate a Technique to Identify Sources of Silicone Contamination

Science.gov (United States)

Banks, Bruce A.; deGroh, Kim K.; Baney-Barton, Elyse; Sechkar, Edward A.; Hunt, Patricia K.; Willoughby, Alan; Bemer, Meagan; Hope, Stephanie; Koo, Julie; Kaminski, Carolyn;

Bacterial biofilms and antibiotic resistance

Directory of Open Access Journals (Sweden)

Liliana Caldas-Arias

2015-04-01

Full Text Available Biofilms give to bacteria micro-environmental benefits; confers protection against antimicrobials. Bacteria have antibiotic resistance by conventional and unusual mechanisms leading to delayed wound healing, to increase recurrent chronic infections and nosocomial contamination of medical devices. Objective: This narrative review aims to introduce the characteristics of Bacteria-biofilms, antimicrobial resistance mechanisms and potential alternatives for prevention and control of its formation. Methods: Search strategy was performed on records: PubMed / Medline, Lilacs, Redalyc; with suppliers such as EBSCO and thesaurus MeSH and DeCS. Conclusions: Knowledge and research performance of biofilm bacteria are relevant in the search of technology for detection and measuring sensitivity to antibiotics. The identification of Bacterial-biofilms needs no-traditional microbiological diagnosis.

Groundwater redox conditions and conductivity in a contaminant plume from geoelectrical investigations

Directory of Open Access Journals (Sweden)

V. Naudet

2004-01-01

Full Text Available Accurate mapping of the electrical conductivity and of the redox potential of the groundwater is important in delineating the shape of a contaminant plume. A map of redox potential in an aquifer is indicative of biodegradation of organic matter and of concentrations of redox-active components; a map of electrical conductivity provides information on the mineralisation of the groundwater. Both maps can be used to optimise the position of pumping wells for remediation. The self-potential method (SP and electrical resistivity tomography (ERT have been applied to the contaminant plume associated with the Entressen landfill in south-east France. The self-potential depends on groundwater flow (electrokinetic contribution and redox conditions ('electro-redox' contribution. Using the variation of the piezometric head in the aquifer, the electrokinetic contribution is removed from the SP signals. A good linear correlation (R2=0.85 is obtained between the residual SP data and the redox potential values measured in monitoring wells. This relationship is used to draw a redox potential map of the overall contaminated site. The electrical conductivity of the subsoil is obtained from 3D-ERT analysis. A good linear correlation (R2=0.91 is observed between the electrical conductivity of the aquifer determined from the 3D-ERT image and the conductivity of the groundwater measured in boreholes. This indicates that the formation factor is nearly homogeneous in the shallow aquifer at the scale of the ERT. From this correlation, a map of the pore water conductivity of the aquifer is obtained. Keywords: self-potential, redox potential, electrical resistivity tomography, fluid conductivity, contaminant plume

Dynamic capabilities and innovation capabilities: The case of the ‘Innovation Clinic’

Directory of Open Access Journals (Sweden)

Fred Strønen

2017-01-01

Full Text Available In this explorative study, we investigate the relationship between dynamic capabilities and innovation capabilities. Dynamic capabilities are at the core of strategic management in terms of how firms can ensure adaptation to changing environments over time. Our paper follows two paths of argumentation. First, we review and discuss some major contributions to the theories on ordinary capabilities, dynamic capabilities, and innovation capabilities. We seek to identify different understandings of the concepts in question, in order to clarify the distinctions and relationships between dynamic capabilities and innovation capabilities. Second, we present a case study of the ’Innovation Clinic’ at a major university hospital, including four innovation projects. We use this case study to explore and discuss how dynamic capabilities can be extended, as well as to what extent innovation capabilities can be said to be dynamic. In our conclusion, we discuss the conditions for nurturing ‘dynamic innovation capabilities’ in organizations.

Disposal sheet for preventing scattering of radioactive contaminated material

International Nuclear Information System (INIS)

Miyasaka, Shun-ichi; Kurioka, Hitoshi; Nakamura, Kenjiro.

1990-01-01

Upon disposal of vinyl sheets at the final stage of dismantling operation for nuclear buildings, etc., radioactive contaminated materials caused by cutting concretes, etc. remain on the sheets. In view of the above, members capable of restoring original shape due to the temperature difference are attached to the sheet main body so that the sheet main body may be folded into a bag-like shape. Since the members as described above are bent upon temperature elevation in the sheets, the sheet main body is pulled by the members and then spontaneously folded into a bag-like shape. As a result, the radioactive contaminated materials remaining on the sheets are wrapped into the sheet main body free from touch to operator's hands or without scattering to the surrounding. This can prevent operator's external and internal exposure. (T.M.)

Evaluation of Antibiotic Resistance Patterns and Heavy Metals ...

African Journals Online (AJOL)

PROF HORSFALL

Bacteria Isolated from Contaminated Soils and Sediments from Warri, Delta ... Faculty of Life Sciences, University of Benin, P.M.B 1154, Benin City, Nigeria. ... atmosphere, soil and water bodies (Ali et al., 2013). ... Antimicrobial drug resistance in bacterial pathogens is ... to the laboratory and stored at 4°C prior to microbial.

Mechanisms of Candida biofilm drug resistance

Science.gov (United States)

Taff, Heather T; Mitchell, Kaitlin F; Edward, Jessica A; Andes, David R

2013-01-01

Candida commonly adheres to implanted medical devices, growing as a resilient biofilm capable of withstanding extraordinarily high antifungal concentrations. As currently available antifungals have minimal activity against biofilms, new drugs to treat these recalcitrant infections are urgently needed. Recent investigations have begun to shed light on the mechanisms behind the profound resistance associated with the biofilm mode of growth. This resistance appears to be multifactorial, involving both mechanisms similar to conventional, planktonic antifungal resistance, such as increased efflux pump activity, as well as mechanisms specific to the biofilm lifestyle. A unique biofilm property is the production of an extracellular matrix. Two components of this material, β-glucan and extracellular DNA, promote biofilm resistance to multiple antifungals. Biofilm formation also engages several stress response pathways that impair the activity of azole drugs. Resistance within a biofilm is often heterogeneous, with the development of a subpopulation of resistant persister cells. In this article we review the molecular mechanisms underlying Candida biofilm antifungal resistance and their relative contributions during various growth phases. PMID:24059922

Prevalence of antibiotic resistance in bacteria isolated from drinking well water available in Guinea-Bissau (West Africa).

Science.gov (United States)

Machado, A; Bordalo, A A

2014-08-01

The dissemination of antibiotic-resistant bacteria and the spread of antibiotic resistance genes are a major public health concern worldwide, being even proposed as emerging contaminants. The aquatic environment is a recognized reservoir of antibiotic resistant bacteria, and antibiotic resistance genes have been recently detected in drinking water. In this study, the water quality and the prevalence of antibiotic resistance of heterotrophic culturable bacteria were characterized seasonally in wells that serve the population of Guinea-Bissau (West Africa) as the sole source of water for drinking and other domestic proposes. The results revealed that well water was unfit for human consumption independently of the season, owing to high acidity and heavy fecal contamination. Moreover, potentially pathogenic bacteria, which showed resistance to the most prescribed antibiotics in Guinea-Bissau, were isolated from well water, posing an additional health risk. Our results suggest that well water not only fosters the transmission of potential pathogenic bacteria, but also represents an important reservoir for the proliferation of antibiotic resistant bacteria, that can aggravate the potential to cause disease in a very vulnerable population that has no other alternative but to consume such water. Copyright © 2014 Elsevier Inc. All rights reserved.

Susceptibility of Pediococcus isolates to antimicrobial compounds in relation to hop-resistance and beer-spoilage.

Science.gov (United States)

Haakensen, Monique; Vickers, David M; Ziola, Barry

2009-09-07

Though important in the context of food microbiology and as potential pathogens in immuno-compromised humans, bacterial isolates belonging to the genus Pediococcus are best known for their association with contamination of ethanol fermentation processes (beer, wine, or fuel ethanol). Use of antimicrobial compounds (e.g., hop-compounds, Penicillin) by some industries to combat Pediococcus contaminants is long-standing, yet knowledge about the resistance of pediococci to antimicrobial agents is minimal. Here we examined Pediococcus isolates to determine whether antibiotic resistance is associated with resistance to hops, presence of genes known to correlate with beer spoilage, or with ability to grow in beer. Lactic acid bacteria susceptibility test broth medium (LSM) used in combination with commercially available GPN3F antimicrobial susceptibility plates was an effective method for assessing antimicrobial susceptibility of Pediococcus isolates. We report the finding of Vancomycin-susceptible Pediococcus isolates from four species. Interestingly, we found that hop-resistant, beer-spoilage, and beer-spoilage gene-harbouring isolates had a tendency to be more susceptible, rather than more resistant, to antimicrobial compounds. Our findings indicate that the mechanisms involved in conferring hop-resistance or ability to spoil beer by Pediococcus isolates are not associated with resistance to antibiotics commonly used for treatment of human infections. Also, Vancomycin-resistance was found to be isolate-specific and not intrinsic to the genus as previously believed.

SoK: Making Sense of Censorship Resistance Systems

Directory of Open Access Journals (Sweden)

Khattak Sheharbano

2016-10-01

Full Text Available An increasing number of countries implement Internet censorship at different scales and for a variety of reasons. Several censorship resistance systems (CRSs have emerged to help bypass such blocks. The diversity of the censor’s attack landscape has led to an arms race, leading to a dramatic speed of evolution of CRSs. The inherent complexity of CRSs and the breadth of work in this area makes it hard to contextualize the censor’s capabilities and censorship resistance strategies. To address these challenges, we conducted a comprehensive survey of CRSs-deployed tools as well as those discussed in academic literature-to systematize censorship resistance systems by their threat model and corresponding defenses. To this end, we first sketch a comprehensive attack model to set out the censor’s capabilities, coupled with discussion on the scope of censorship, and the dynamics that influence the censor’s decision. Next, we present an evaluation framework to systematize censorship resistance systems by their security, privacy, performance and deployability properties, and show how these systems map to the attack model. We do this for each of the functional phases that we identify for censorship resistance systems: communication establishment, which involves distribution and retrieval of information necessary for a client to join the censorship resistance system; and conversation, where actual exchange of information takes place. Our evaluation leads us to identify gaps in the literature, question the assumptions at play, and explore possible mitigations.

Untreated urban waste contaminates Indian river sediments with resistance genes to last resort antibiotics.

Science.gov (United States)

Marathe, Nachiket P; Pal, Chandan; Gaikwad, Swapnil S; Jonsson, Viktor; Kristiansson, Erik; Larsson, D G Joakim

2017-11-01

Efficient sewage treatment is critical for limiting environmental transmission of antibiotic-resistant bacteria. In many low and middle income countries, however, large proportions of sewage are still released untreated into receiving water bodies. In-depth knowledge of how such discharges of untreated urban waste influences the environmental resistome is largely lacking. Here, we highlight the impact of uncontrolled discharge of partially treated and/or untreated wastewater on the structure of bacterial communities and resistome of sediments collected from Mutha river flowing through Pune city in India. Using shotgun metagenomics, we found a wide array (n = 175) of horizontally transferable antibiotic resistance genes (ARGs) including carbapenemases such as NDM, VIM, KPC, OXA-48 and IMP types. The relative abundance of total ARGs was 30-fold higher in river sediments within the city compared to upstream sites. Forty four ARGs, including the tet(X) gene conferring resistance to tigecycline, OXA-58 and GES type carbapenemases, were significantly more abundant in city sediments, while two ARGs were more common at upstream sites. The recently identified mobile colistin resistance gene mcr-1 was detected only in one of the upstream samples, but not in city samples. In addition to ARGs, higher abundances of various mobile genetic elements were found in city samples, including integron-associated integrases and ISCR transposases, as well as some biocide/metal resistance genes. Virulence toxin genes as well as bacterial genera comprising many pathogens were more abundant here; the genus Acinetobacter, which is often associated with multidrug resistance and nosocomial infections, comprised up to 29% of the 16S rRNA reads, which to our best knowledge is unmatched in any other deeply sequenced metagenome. There was a strong correlation between the abundance of Acinetobacter and the OXA-58 carbapenemase gene. Our study shows that uncontrolled discharge of untreated urban

Capability ethics

OpenAIRE

Robeyns, Ingrid

2012-01-01

textabstractThe capability approach is one of the most recent additions to the landscape of normative theories in ethics and political philosophy. Yet in its present stage of development, the capability approach is not a full-blown normative theory, in contrast to utilitarianism, deontological theories, virtue ethics, or pragmatism. As I will argue in this chapter, at present the core of the capability approach is an account of value, which together with some other (more minor) normative comm...

Performance of μ-RWELL detector vs resistivity of the resistive stage

Science.gov (United States)

Bencivenni, G.; De Oliveira, R.; Felici, G.; Gatta, M.; Morello, G.; Ochi, A.; Lener, M. Poli; Tskhadadze, E.

2018-04-01

The μ-RWELL is a compact spark-protected single amplification stage Micro-Pattern-Gaseous-Detector (MPGD). The detector amplification stage is realized with a polyimide structure, micro-patterned with a dense matrix of blind-holes, integrated into the readout structure. The anode is formed by a thin Diamond Like Carbon (DLC) resistive layer separated by an insulating glue layer from the readout strips. The introduction of the resistive layer strongly suppressing the transition from streamer to spark gives the possibility to achieve large gains (> 104), without significantly affecting the capability to be efficiently operated in high particle fluxes. In this work we present the results of a systematic study of the μ-RWELL performance as a function of the DLC resistivity. The tests have been performed either with collimated 5.9 keV X-rays or with pion and muon beams at the SPS Secondary Beamline H4 and H8 at CERN.

A multi-process phytoremediation system for removal of polycyclic aromatic hydrocarbons from contaminated soils

International Nuclear Information System (INIS)

Huang Xiaodong; El-Alawi, Yousef; Penrose, Donna M.; Glick, Bernard R.; Greenberg, Bruce M.

2004-01-01

To improve phytoremediation processes, multiple techniques that comprise different aspects of contaminant removal from soils have been combined. Using creosote as a test contaminant, a multi-process phytoremediation system composed of physical (volatilization), photochemical (photooxidation) and microbial remediation, and phytoremediation (plant-assisted remediation) processes was developed. The techniques applied to realize these processes were land-farming (aeration and light exposure), introduction of contaminant degrading bacteria, plant growth promoting rhizobacteria (PGPR), and plant growth of contaminant-tolerant tall fescue (Festuca arundinacea). Over a 4-month period, the average efficiency of removal of 16 priority PAHs by the multi-process remediation system was twice that of land-farming, 50% more than bioremediation alone, and 45% more than phytoremediation by itself. Importantly, the multi-process system was capable of removing most of the highly hydrophobic, soil-bound PAHs from soil. The key elements for successful phytoremediation were the use of plant species that have the ability to proliferate in the presence of high levels of contaminants and strains of PGPR that increase plant tolerance to contaminants and accelerate plant growth in heavily contaminated soils. The synergistic use of these approaches resulted in rapid and massive biomass accumulation of plant tissue in contaminated soil, putatively providing more active metabolic processes, leading to more rapid and more complete removal of PAHs. - Persistent PAH contaminants in soils can be removed more completely and rapidly by using multiple remediation processes

Protection of Steel Rebar in Salt-Contaminated Cement Mortar Using Epoxy Nanocomposite Coatings

Directory of Open Access Journals (Sweden)

The Huu Nguyen