Environmental contamination, product contamination and workers exposure using a robotic system for antineoplastic drug preparation.

Science.gov (United States)

Sessink, Paul J M; Leclercq, Gisèle M; Wouters, Dominique-Marie; Halbardier, Loïc; Hammad, Chaïma; Kassoul, Nassima

2015-04-01

Environmental contamination, product contamination and technicians exposure were measured following preparation of iv bags with cyclophosphamide using the robotic system CytoCare. Wipe samples were taken inside CytoCare, in the clean room environment, from vials, and prepared iv bags including ports and analysed for contamination with cyclophosphamide. Contamination with cyclophosphamide was also measured in environmental air and on the technicians hands and gloves used for handling the drugs. Exposure of the technicians to cyclophosphamide was measured by analysis of cyclophosphamide in urine. Contamination with cyclophosphamide was mainly observed inside CytoCare, before preparation, after preparation and after daily routine cleaning. Contamination outside CytoCare was incidentally found. All vials with reconstituted cyclophosphamide entering CytoCare were contaminated on the outside but vials with powdered cyclophosphamide were not contaminated on the outside. Contaminated bags entering CytoCare were also contaminated after preparation but non-contaminated bags were not contaminated after preparation. Cyclophosphamide was detected on the ports of all prepared bags. Almost all outer pairs of gloves used for preparation and daily routine cleaning were contaminated with cyclophosphamide. Cyclophosphamide was not found on the inner pairs of gloves and on the hands of the technicians. Cyclophosphamide was not detected in the stationary and personal air samples and in the urine samples of the technicians. CytoCare enables the preparation of cyclophosphamide with low levels of environmental contamination and product contamination and no measurable exposure of the technicians. © The Author(s) 2014 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

Light contamination

International Nuclear Information System (INIS)

Cepeda Pena, William Enrique

1998-01-01

The article tries on the wrong use of the artificial light, of the main problems of the light contamination, dispersion of the light, noxious effects of the light contamination, ecological effects, effects on the man's biological rhythm, economic effects and effects about the civic and vial security, among other topics

Bacterial Hand Contamination and Transfer after Use of Contaminated Bulk-Soap-Refillable Dispensers▿†

OpenAIRE

Zapka, Carrie A.; Campbell, Esther J.; Maxwell, Sheri L.; Gerba, Charles P.; Dolan, Michael J.; Arbogast, James W.; Macinga, David R.

2011-01-01

Bulk-soap-refillable dispensers are prone to extrinsic bacterial contamination, and recent studies demonstrated that approximately one in four dispensers in public restrooms are contaminated. The purpose of this study was to quantify bacterial hand contamination and transfer after use of contaminated soap under controlled laboratory and in-use conditions in a community setting. Under laboratory conditions using liquid soap experimentally contaminated with 7.51 log10 CFU/ml of Serratia marcesc...

Nuclear explosion and internal contamination; Explosion nucleaire et contamination interne

Energy Technology Data Exchange (ETDEWEB)

Aeberhardt, A [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires

1956-07-01

By the study of the conditions of internal contamination due to the radioactive mixture produced by a nuclear explosion, the parts played by the relative weights of the different elements and the mode of expression of the doses are considered. Only the knowledge of the weight composition of the contamination mixture and of its evolution as a function of time can provide the required basis for the study of its metabolism in the organism. The curves which give the composition of the fission product mixture - in number of nuclei - - as a function of time - have been established. These curves are applied to some practical examples, particularly relative to the nature of contamination, radiotoxicity of some elements and assessment of hazards. (author) [French] Etudiant les modalites de la contamination interne par les elements radioactifs apparus lors d'une explosion nucleaire, le role de la 'masse' et le mode d'expression des doses sont envisages. La connaissance de la composition en 'masse' du melange contaminant et de son evolution en fonction du temps peut seule apporter les bases necessaires a l'etude de son comportement dans l'organisme. Les courbes donnant la composition du melange de produits de fission - en nombre de noyaux - - en fonction du temps - ont ete etablies. Quelques applications pratiques, relatives en particulier a la nature de la contamination, a la radiotoxicite de certains elements et a l'evaluation de risque, sont envisagees a titre d'exemple. (auteur)

Containing and discarding method for radiation contaminated materials and radiation contaminated material containing composite member

International Nuclear Information System (INIS)

Akagawa, Katsuhiko.

1995-01-01

A container for high level radiation contaminated materials is loaded in an outer container in a state of forming a gap between the outer container and a container wall, low level radiation contaminated materials are filled to the gap between the container of the radiation contaminated materials and the container wall, and then the outer container is sealed. In addition, the thickness of the layer of the low level radiation contaminated materials is made substantially uniform. Then, since radiation rays from the container of the radiation contaminated materials are decayed by the layer of the low level radiation contaminated materials at the periphery of the container and the level of the radiation rays emitted from the outer container is extremely reduced than in a case where the entire amount of high level radiation contaminated materials are filled, the level is suppressed to an extent somewhat higher than the level in the case where the entire amount of the low level radiation contaminated materials are filled. Accordingly, the management corresponds to that for the low level radiation contaminated materials, and the steps for the management and the entire volume thereof are reduced than in a case where the high level radiation contaminated materials and the low level radiation contaminated materials are sealed separately. (N.H.)

Contamination Control for Thermal Engineers

Science.gov (United States)

Rivera, Rachel B.

2015-01-01

The presentation will be given at the 26th Annual Thermal Fluids Analysis Workshop (TFAWS 2015) hosted by the Goddard Spaceflight Center (GSFC) Thermal Engineering Branch (Code 545). This course will cover the basics of Contamination Control, including contamination control related failures, the effects of contamination on Flight Hardware, what contamination requirements translate to, design methodology, and implementing contamination control into Integration, Testing and Launch.

JPL Contamination Control Engineering

Science.gov (United States)

Blakkolb, Brian

2013-01-01

JPL has extensive expertise fielding contamination sensitive missions-in house and with our NASA/industry/academic partners.t Development and implementation of performance-driven cleanliness requirements for a wide range missions and payloads - UV-Vis-IR: GALEX, Dawn, Juno, WFPC-II, AIRS, TES, et al - Propulsion, thermal control, robotic sample acquisition systems. Contamination control engineering across the mission life cycle: - System and payload requirements derivation, analysis, and contamination control implementation plans - Hardware Design, Risk trades, Requirements V-V - Assembly, Integration & Test planning and implementation - Launch site operations and launch vehicle/payload integration - Flight ops center dot Personnel on staff have expertise with space materials development and flight experiments. JPL has capabilities and expertise to successfully address contamination issues presented by space and habitable environments. JPL has extensive experience fielding and managing contamination sensitive missions. Excellent working relationship with the aerospace contamination control engineering community/.

Bioremediation of contaminated soil

International Nuclear Information System (INIS)

Balba, M.T.; Ying, A.C.; McNeice, T.G.

1992-01-01

Microorganisms, especially bacteria, yeast and fungi are capable of degrading many kinds of xenobiotic compounds and toxic chemicals such as petroleum hydrocarbon compounds. These microorganisms are ubiquitous in nature and, despite their enormous versatility, there are numerous cases in which long-term contamination of soil and groundwater has been observed. The persistence of the contamination is usually caused by the inability of microorganisms to metabolize these compounds under the prevailing environmental condition. This paper reports on biological remediation of contaminated sites which can be accomplished by using naturally-occurring microorganisms to treat the contaminants. The development of a bioremediation program for a specific contaminated soil system usually includes: A thorough site/soil/waste characterization; Treatability studies

Contamination control plan for prelaunch operations

Science.gov (United States)

Austin, J. D.

1983-01-01

A unified, systematic plan is presented for contamination control for space flight systems. Allowable contaminant quantities, or contamination budgets, are determined based on system performance margins and system-level allowable degradations. These contamination budgets are compared to contamination rates in ground environments to establish the controls required in each ground environment. The use of feedback from contamination monitoring and some contamination control procedures are discussed.

NCRP soil contamination task group

International Nuclear Information System (INIS)

Jacobs, D.G.

1987-01-01

The National Council of Radiation Protection and Measurements (NCRP) has recently established a Task Group on Soil Contamination to describe and evaluate the migration pathways and modes of radiation exposure that can potentially arise due to radioactive contamination of soil. The purpose of this paper is to describe the scientific principles for evaluation of soil contamination which can be used as a basis for derivation of soil contamination limits for specific situations. This paper describes scenarios that can lead to soil contamination, important characteristics of soil contamination, the subsequent migration pathways and exposure modes, and the application of principles in the report in deriving soil contamination limits. The migration pathways and exposure modes discussed in this paper include: direct radiation exposure; and exhalation of gases

Subsurface contaminants focus area

International Nuclear Information System (INIS)

1996-08-01

The US Department of Enregy (DOE) Subsurface Contaminants Focus Area is developing technologies to address environmental problems associated with hazardous and radioactive contaminants in soil and groundwater that exist throughout the DOE complex, including radionuclides, heavy metals; and dense non-aqueous phase liquids (DNAPLs). More than 5,700 known DOE groundwater plumes have contaminated over 600 billion gallons of water and 200 million cubic meters of soil. Migration of these plumes threatens local and regional water sources, and in some cases has already adversely impacted off-site rsources. In addition, the Subsurface Contaminants Focus Area is responsible for supplying technologies for the remediation of numerous landfills at DOE facilities. These landfills are estimated to contain over 3 million cubic meters of radioactive and hazardous buried Technology developed within this specialty area will provide efective methods to contain contaminant plumes and new or alternative technologies for development of in situ technologies to minimize waste disposal costs and potential worker exposure by treating plumes in place. While addressing contaminant plumes emanating from DOE landfills, the Subsurface Contaminants Focus Area is also working to develop new or alternative technologies for the in situ stabilization, and nonintrusive characterization of these disposal sites

Subsurface contaminants focus area

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-08-01

The US Department of Enregy (DOE) Subsurface Contaminants Focus Area is developing technologies to address environmental problems associated with hazardous and radioactive contaminants in soil and groundwater that exist throughout the DOE complex, including radionuclides, heavy metals; and dense non-aqueous phase liquids (DNAPLs). More than 5,700 known DOE groundwater plumes have contaminated over 600 billion gallons of water and 200 million cubic meters of soil. Migration of these plumes threatens local and regional water sources, and in some cases has already adversely impacted off-site rsources. In addition, the Subsurface Contaminants Focus Area is responsible for supplying technologies for the remediation of numerous landfills at DOE facilities. These landfills are estimated to contain over 3 million cubic meters of radioactive and hazardous buried Technology developed within this specialty area will provide efective methods to contain contaminant plumes and new or alternative technologies for development of in situ technologies to minimize waste disposal costs and potential worker exposure by treating plumes in place. While addressing contaminant plumes emanating from DOE landfills, the Subsurface Contaminants Focus Area is also working to develop new or alternative technologies for the in situ stabilization, and nonintrusive characterization of these disposal sites.

Fluorescence Imaging Reveals Surface Contamination

Science.gov (United States)

Schirato, Richard; Polichar, Raulf

1992-01-01

In technique to detect surface contamination, object inspected illuminated by ultraviolet light to make contaminants fluoresce; low-light-level video camera views fluorescence. Image-processing techniques quantify distribution of contaminants. If fluorescence of material expected to contaminate surface is not intense, tagged with low concentration of dye.

Understanding Mechanisms of Radiological Contamination

Energy Technology Data Exchange (ETDEWEB)

Rick Demmer; John Drake; Ryan James, PhD

2014-03-01

Over the last 50 years, the study of radiological contamination and decontamination has expanded significantly. This paper addresses the mechanisms of radiological contamination that have been reported and then discusses which methods have recently been used during performance testing of several different decontamination technologies. About twenty years ago the Idaho Nuclear Technology Engineering Center (INTEC) at the INL began a search for decontamination processes which could minimize secondary waste. In order to test the effectiveness of these decontamination technologies, a new simulated contamination, termed SIMCON, was developed. SIMCON was designed to replicate the types of contamination found on stainless steel, spent fuel processing equipment. Ten years later, the INL began research into methods for simulating urban contamination resulting from a radiological dispersal device (RDD). This work was sponsored by the Defense Advanced Research Projects Agency (DARPA) and included the initial development an aqueous application of contaminant to substrate. Since 2007, research sponsored by the US Environmental Protection Agency (EPA) has advanced that effort and led to the development of a contamination method that simulates particulate fallout from an Improvised Nuclear Device (IND). The IND method diverges from previous efforts to create tenacious contamination by simulating a reproducible “loose” contamination. Examining these different types of contamination (and subsequent decontamination processes), which have included several different radionuclides and substrates, sheds light on contamination processes that occur throughout the nuclear industry and in the urban environment.

Biological Remediation of Petroleum Contaminants

Science.gov (United States)

Kuhad, Ramesh Chander; Gupta, Rishi

Large volumes of hazardous wastes are generated in the form of oily sludges and contaminated soils during crude oil transportation and processing. Although many physical, chemical and biological treatment technologies are available for petroleum contaminants petroleum contaminants in soil, biological methods have been considered the most cost-effective. Practical biological remediation methods typically involve direct use of the microbes naturally occurring in the contaminated environment and/or cultured indigenous or modified microorganisms. Environmental and nutritional factors, including the properties of the soil, the chemical structure of the hydrocarbon(s), oxygen, water, nutrient availability, pH, temperature, and contaminant bioavailability, can significantly affect the rate and the extent of hydrocarbon biodegradation hydrocarbon biodegradation by microorganisms in contaminated soils. This chapter concisely discusses the major aspects of bioremediation of petroleum contaminants.

Modelling of contamination of surface atmosphere for deflation of Cesium-137 on contaminated territories

International Nuclear Information System (INIS)

Bogdanov, A.P.; Zhmura, G.M.

1994-01-01

Presence of Cesium 137 in near land air is caused at the contaminated territories by 'local' dusting and transport of the dust from the zone of strong contamination. For large distance is it caused by resuspension of radioactive dust from the surface in the given region. In accordance with the models of dusting round square sources based on Gauss statistical model of dissemination of admixtures in the atmosphere, the contaminated areas of european part of the former of USSR with the density of contamination over 1 Ci/km 2 with Cesium 137 were represented by 30 round square sources covering the main spots of contamination. The results of calculation of contamination of the atmosphere for several cities of Belarus, Russia and Ukraine, where there are the permanent points of observation for the content of radionuclides in the air, have shown that the proposed model of dusting sources describes the contamination of near land air with Cesium 137 reasonably well. 7 refs., 3 tabs

9 CFR 381.91 - Contamination.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 2 2010-01-01 2010-01-01 false Contamination. 381.91 Section 381.91... § 381.91 Contamination. (a) Carcasses of poultry contaminated by volatile oils, paints, poisons, gases... station away from the main processing line, by any method that will remove the contamination, such as...

Human Contamination in Public Genome Assemblies.

Science.gov (United States)

Kryukov, Kirill; Imanishi, Tadashi

2016-01-01

Contamination in genome assembly can lead to wrong or confusing results when using such genome as reference in sequence comparison. Although bacterial contamination is well known, the problem of human-originated contamination received little attention. In this study we surveyed 45,735 available genome assemblies for evidence of human contamination. We used lineage specificity to distinguish between contamination and conservation. We found that 154 genome assemblies contain fragments that with high confidence originate as contamination from human DNA. Majority of contaminating human sequences were present in the reference human genome assembly for over a decade. We recommend that existing contaminated genomes should be revised to remove contaminated sequence, and that new assemblies should be thoroughly checked for presence of human DNA before submitting them to public databases.

Reconditioning contaminated gravel

International Nuclear Information System (INIS)

Walsh, H.; Bowers, J.S.; Cadwell, K.

1995-02-01

Lawrence Livermore National Laboratory (LLNL) has developed a portable screening system that will recondition radioactively contaminated gravel in the field. The separation technique employed by this system removes dirt, contaminated debris, and other fine particles from gravel. At LLNL, gravel is used in conjunction with the experimental testing of explosives to reduce shock wave propagation. The gravel surrounds the experimental device and buffers the energy generated from the explosion. During an explosion, some of the gravel is broken down into small particles and mixed with contaminants. Contaminants in the used gravel originate from metal sheathing and other parts comprising, the experimental device. These contaminants may consist of radionuclides and metals that are considered hazardous by the State of California when disposed. This paper describes the process that conveys contaminated material into the screener system, sprays the material with recycled water or other mild cleaning chemicals, and separates particles based on size. Particles greater than a specified size are discharged out of the screener separator and recycled back into use, thereby reducing the amount of mixed waste generated and minimizing the need for new gravel. The fines or silt are flushed out of the separator with the water and are removed from the water and consolidated into a drum with the use of a hydrocyclone separator and drum decant system. Because the water in the spray system is recycled, minimal makeup water is needed. The system monitors pH and total dissolved solids

Restoration of contaminated soils

International Nuclear Information System (INIS)

Miranda J, Jose Eduardo

2009-01-01

A great variety of techniques are used for the restoration of contaminated soils. The contamination is present by both organic and inorganic pollutants. Environmental conditions and soil characteristics should take into account in order to implement a remedial technique. The bioremediation technologies are showed as help to remove a variety of soil contaminants. (author) [es

[Perceived risks of food contaminants].

Science.gov (United States)

Koch, Severine; Lohmann, Mark; Epp, Astrid; Böl, Gaby-Fleur

2017-07-01

Food contaminants can pose a serious health threat. In order to carry out adequate risk communication measures, the subjective risk perception of the public must be taken into account. In this context, the breadth of the topic and insufficient terminological delimitations from residues and food additives make an elaborate explanation of the topic to consumers indispensable. A representative population survey used language adequate for lay people and a clear definition of contaminants to measure risk perceptions with regard to food contaminants among the general public. The study aimed to assess public awareness of contaminants and the perceived health risks associated with them. In addition, people's current knowledge and need for additional information, their attitudes towards contaminants, views on stakeholder accountability, as well as compliance with precautionary measures, such as avoiding certain foods to reduce health risks originating from contaminants, were assessed. A representative sample of 1001 respondents was surveyed about food contaminants via computer-assisted telephone interviewing. The majority of respondents rated contaminants as a serious health threat, though few of them spontaneously mentioned examples of undesirable substances in foods that fit the scientific or legal definition of contaminants. Mercury and dioxin were the most well-known contaminants. Only a minority of respondents was familiar with pyrrolizidine alkaloids. The present findings highlight areas that require additional attention and provide implications for risk communication geared to specific target groups.

Body-surface contamination monitoring preparatory to monitoring for internal contamination

International Nuclear Information System (INIS)

Schlueter, W.; Klucke, H.

1980-01-01

Measurements in the whole-body counter of the SAAS are routinely preceded by a thorough inspection of the patients for body-surface contamination to protect the sensitive counting equipment against becoming contaminated and to avoid a falsified indication of incorporated radionuclides. The measuring system employed for these examinations is described. (author)

Contamination monitoring activities in Kanupp

Energy Technology Data Exchange (ETDEWEB)

Naqvi, S S [Karachi Nuclear Power Plant (Pakistan)

1997-06-01

The Karachi Nuclear Power Plant (Kanupp) is a 137 MWe pressurized heavy water reactor, designed and erected by the Canadian General Electric Company as a turn key project. The plant is in operation since it was commissioned in the year 1972. It is located at the Arabian Sea Coast about 15 miles to the west of Karachi. During its more than two decades of operation, the plant has generated about 8 billion units of electricity with an average life time availability factor of 60%. In Kanupp, radioactive contamination may exit due to the release of fission product, activation products etc., which may somehow escape from its confinement and may contaminate surface or other media such as air, water etc. In this paper, following items are described: main aspects of contamination, status of contamination monitoring, need of contamination monitoring, radiation protection activity, instruments, contamination, current status of contamination survey materials and their disposal, and environmental monitoring. (G.K.)

ICRP-26 and skin contamination

International Nuclear Information System (INIS)

Finnigan, T.; Huda, W.; Newbery, G.R.

1979-01-01

The experience of dealing with skin contamination incidents at The Radiochemical Centre over a 3-year period is presented. Data are given for the primary isotopes involved, the duration of skin contamination, and the skin doses that arise from these incidents. The methods employed in performing dosimetry for skin contamination are discussed and examples involving the isotopes carbon-14 and indium-111 are described. For skin contamination incidents, the mode of penetration of the activity into skin is normally not known and this can be of major significance for the final skin dose estimate. The operational health physics difficulties encountered in complying with both ICRP-26 and UK legislation for skin contamination are considered. In the event of multiple exposure (i.e. skin doses calculated from whole body film badges, extremity TLD dose meters and skin contamination) there is ambiguity in the precise meaning of the skin dose. The usefulness of Derived Working Levels is also discussed. Experience at The Radiochemical Centre has shown that good plant design, proper training and prompt action in dealing with contamination incidents ensures that overexposures to skin from accidental contamination are rare occurrences. (author)

ContaMiner and ContaBase: a webserver and database for early identification of unwantedly crystallized protein contaminants

KAUST Repository

Hungler, Arnaud; Momin, Afaque Ahmad Imtiyaz; Diederichs, Kay; Arold, Stefan T.

2016-01-01

Solving the phase problem in protein X-ray crystallography relies heavily on the identity of the crystallized protein, especially when molecular replacement (MR) methods are used. Yet, it is not uncommon that a contaminant crystallizes instead of the protein of interest. Such contaminants may be proteins from the expression host organism, protein fusion tags or proteins added during the purification steps. Many contaminants co-purify easily, crystallize and give good diffraction data. Identification of contaminant crystals may take time, since the presence of the contaminant is unexpected and its identity unknown. A webserver (ContaMiner) and a contaminant database (ContaBase) have been established, to allow fast MR-based screening of crystallographic data against currently 62 known contaminants. The web-based ContaMiner (available at http://strube.cbrc.kaust.edu.sa/contaminer/) currently produces results in 5 min to 4 h. The program is also available in a github repository and can be installed locally. ContaMiner enables screening of novel crystals at synchrotron beamlines, and it would be valuable as a routine safety check for 'crystallization and preliminary X-ray analysis' publications. Thus, in addition to potentially saving X-ray crystallographers much time and effort, ContaMiner might considerably lower the risk of publishing erroneous data. A web server, titled ContaMiner, has been established, which allows fast molecular-replacement-based screening of crystallographic data against a database (ContaBase) of currently 62 potential contaminants. ContaMiner enables systematic screening of novel crystals at synchrotron beamlines, and it would be valuable as a routine safety check for 'crystallization and preliminary X-ray analysis' publications. © Arnaud Hungler et al. 2016.

ContaMiner and ContaBase: a webserver and database for early identification of unwantedly crystallized protein contaminants

KAUST Repository

Hungler, Arnaud

2016-11-02

Solving the phase problem in protein X-ray crystallography relies heavily on the identity of the crystallized protein, especially when molecular replacement (MR) methods are used. Yet, it is not uncommon that a contaminant crystallizes instead of the protein of interest. Such contaminants may be proteins from the expression host organism, protein fusion tags or proteins added during the purification steps. Many contaminants co-purify easily, crystallize and give good diffraction data. Identification of contaminant crystals may take time, since the presence of the contaminant is unexpected and its identity unknown. A webserver (ContaMiner) and a contaminant database (ContaBase) have been established, to allow fast MR-based screening of crystallographic data against currently 62 known contaminants. The web-based ContaMiner (available at http://strube.cbrc.kaust.edu.sa/contaminer/) currently produces results in 5 min to 4 h. The program is also available in a github repository and can be installed locally. ContaMiner enables screening of novel crystals at synchrotron beamlines, and it would be valuable as a routine safety check for \\'crystallization and preliminary X-ray analysis\\' publications. Thus, in addition to potentially saving X-ray crystallographers much time and effort, ContaMiner might considerably lower the risk of publishing erroneous data. A web server, titled ContaMiner, has been established, which allows fast molecular-replacement-based screening of crystallographic data against a database (ContaBase) of currently 62 potential contaminants. ContaMiner enables systematic screening of novel crystals at synchrotron beamlines, and it would be valuable as a routine safety check for \\'crystallization and preliminary X-ray analysis\\' publications. © Arnaud Hungler et al. 2016.

ContaMiner and ContaBase: a webserver and database for early identification of unwantedly crystallized protein contaminants

Science.gov (United States)

Hungler, Arnaud; Momin, Afaque; Diederichs, Kay; Arold, Stefan, T.

2016-01-01

Solving the phase problem in protein X-ray crystallography relies heavily on the identity of the crystallized protein, especially when molecular replacement (MR) methods are used. Yet, it is not uncommon that a contaminant crystallizes instead of the protein of interest. Such contaminants may be proteins from the expression host organism, protein fusion tags or proteins added during the purification steps. Many contaminants co-purify easily, crystallize and give good diffraction data. Identification of contaminant crystals may take time, since the presence of the contaminant is unexpected and its identity unknown. A webserver (ContaMiner) and a contaminant database (ContaBase) have been established, to allow fast MR-based screening of crystallographic data against currently 62 known contaminants. The web-based ContaMiner (available at http://strube.cbrc.kaust.edu.sa/contaminer/) currently produces results in 5 min to 4 h. The program is also available in a github repository and can be installed locally. ContaMiner enables screening of novel crystals at synchrotron beamlines, and it would be valuable as a routine safety check for ‘crystallization and preliminary X-ray analysis’ publications. Thus, in addition to potentially saving X-ray crystallographers much time and effort, ContaMiner might considerably lower the risk of publishing erroneous data. PMID:27980519

Contamination trapped in a cage

International Nuclear Information System (INIS)

Sender, E.

2003-01-01

Some abandoned industrial sites are so strongly contaminated that they threaten to contaminate underground waters. Pollutants are driven through the soil by raining waters. The principle of the ''hydro-Faraday'' cage is to prevent raining waters from flowing through the contaminated part of the soil. The cage is in fact a structure of buried drain tubes that envelop the contaminated zone. Physics make waters flow through the tubes rather than the soil, so the contaminated zone receives no more water and as a consequence pollutants are stopped in their way towards the phreatic bed. (A.C.)

Thermal remediation of tar-contaminated soil and oil-contaminated gravel

International Nuclear Information System (INIS)

Anthony, E.J.; Wang, J.

2005-01-01

High temperature treatments are commonly considered for the decontamination of soil as they have the advantages of reliability, high capacity, and effective destruction of hazardous materials with reduced long-term liability. This paper examined the remediation of soil contaminated by coal tar as well as gravel contaminated by oil. Pilot plant studies were conducted using 2 representative incineration technologies: rotary kiln and fluidized bed. The coal tar contaminated soil had accumulated over a few decades at a calcination plant in western Canada. The soil was sticky and could not be handled by conventional feeding and combustion systems. Crushed lignite was mixed with the soil as an auxiliary fuel and to reduce stickiness. A pilot plant furnace was used to evaluate the potential of decontamination in a rotary calciner. An analysis of both a modelling study and the test results showed that complete decontamination could be achieved in the targeted calciner. The results suggested that energy recovery was also possible, which could in turn make the remediation process more cost-effective. Decontamination of oil-contaminated gravel was conducted with a pilot plant fluidized bed combustor to study the feasibility of using incineration technology in the remediation of gravel and debris contaminated by oil spills. Results indicated that the gravel was decontaminated with acceptable emission performance. It was concluded that the study will be valuable to the application of commercial incineration processes for the remediation of polluted soils. It was observed that the weathering of the oiled gravel lowered the rate of decontamination. A small amount of salt water resulted in lowered decontamination rates, which may be an important factor for situations involving the remediation of shoreline gravel contaminated by oil. 24 refs., 6 tabs., 7 figs

Adsorption and desorption of contaminants

International Nuclear Information System (INIS)

Palumbo, A.V.; Strong-Gunderson, J.M.; DeFlaun, M.; Ensley, B.

1994-01-01

The microbial remediation of sites Contaminated with organics is well documented, however, there are some significant problems that remain to be solved in the areas of contaminants sorbed to soils and non-aqueous phase liquid (NAPL) contamination. Methods of in situ bioremediation techniques employ either the stimulation of indigenous populations by nutrient addition, or the addition of prepared bacterial cultures to the subsurface environment. Problems of contaminant sorption and NAPL's are related in that both encompass reduced contaminant bioavailability. Non-aqueous phase liquids have been identified as a priority area for research in the In situ Program due to their presence at DOE sites and the lack of adequate technology to effectively treat this contamination. Bioremediation technologies developed as a result of this project are easily transferred to industry

[Biological treatments for contaminated soils: hydrocarbon contamination. Fungal applications in bioremediation treatment].

Science.gov (United States)

Martín Moreno, Carmen; González Becerra, Aldo; Blanco Santos, María José

2004-09-01

Bioremediation is a spontaneous or controlled process in which biological, mainly microbiological, methods are used to degrade or transform contaminants to non or less toxic products, reducing the environmental pollution. The most important parameters to define a contaminated site are: biodegradability, contaminant distribution, lixiviation grade, chemical reactivity of the contaminants, soil type and properties, oxygen availability and occurrence of inhibitory substances. Biological treatments of organic contaminations are based on the degradative abilities of the microorganisms. Therefore the knowledge on the physiology and ecology of the biological species or consortia involved as well as the characteristics of the polluted sites are decisive factors to select an adequate biorremediation protocol. Basidiomycetes which cause white rot decay of wood are able to degrade lignin and a variety of environmentally persistent pollutants. Thus, white rot fungi and their enzymes are thought to be useful not only in some industrial process like biopulping and biobleaching but also in bioremediation. This paper provides a review of different aspects of bioremediation technologies and recent advances on ligninolytic metabolism research.

Modeling for Airborne Contamination

International Nuclear Information System (INIS)

F.R. Faillace; Y. Yuan

2000-01-01

The objective of Modeling for Airborne Contamination (referred to from now on as ''this report'') is to provide a documented methodology, along with supporting information, for estimating the release, transport, and assessment of dose to workers from airborne radioactive contaminants within the Monitored Geologic Repository (MGR) subsurface during the pre-closure period. Specifically, this report provides engineers and scientists with methodologies for estimating how concentrations of contaminants might be distributed in the air and on the drift surfaces if released from waste packages inside the repository. This report also provides dose conversion factors for inhalation, air submersion, and ground exposure pathways used to derive doses to potentially exposed subsurface workers. The scope of this report is limited to radiological contaminants (particulate, volatile and gaseous) resulting from waste package leaks (if any) and surface contamination and their transport processes. Neutron activation of air, dust in the air and the rock walls of the drift during the preclosure time is not considered within the scope of this report. Any neutrons causing such activation are not themselves considered to be ''contaminants'' released from the waste package. This report: (1) Documents mathematical models and model parameters for evaluating airborne contaminant transport within the MGR subsurface; and (2) Provides tables of dose conversion factors for inhalation, air submersion, and ground exposure pathways for important radionuclides. The dose conversion factors for air submersion and ground exposure pathways are further limited to drift diameters of 7.62 m and 5.5 m, corresponding to the main and emplacement drifts, respectively. If the final repository design significantly deviates from these drift dimensions, the results in this report may require revision. The dose conversion factors are further derived by using concrete of sufficient thickness to simulate the drift

Environmental contaminants of emerging concern in seafood - European database on contaminant levels

DEFF Research Database (Denmark)

Vandermeersch, Griet; Lourenço, Helena Maria; Alvarez-Muñoz, Diana

2015-01-01

Marine pollution gives rise to concern not only about the environment itself but also about the impact on food safety and consequently on public health. European authorities and consumers have therefore become increasingly worried about the transfer of contaminants from the marine environment...... to seafood.So-called "contaminants of emerging concern" are chemical substances for which no maximum levels have been laid down in EU legislation, or substances for which maximum levels have been provided but which require revision. Adequate information on their presence in seafood is often lacking and thus...... potential risks cannot be excluded. Assessment of food safety issues related to these contaminants has thus become urgent and imperative. A database (www.ecsafeseafooddbase.eu), containing available information on the levels of contaminants of emerging concern in seafood and providing the most recent data...

Bacterial hand contamination and transfer after use of contaminated bulk-soap-refillable dispensers.

Science.gov (United States)

Zapka, Carrie A; Campbell, Esther J; Maxwell, Sheri L; Gerba, Charles P; Dolan, Michael J; Arbogast, James W; Macinga, David R

2011-05-01

Bulk-soap-refillable dispensers are prone to extrinsic bacterial contamination, and recent studies demonstrated that approximately one in four dispensers in public restrooms are contaminated. The purpose of this study was to quantify bacterial hand contamination and transfer after use of contaminated soap under controlled laboratory and in-use conditions in a community setting. Under laboratory conditions using liquid soap experimentally contaminated with 7.51 log(10) CFU/ml of Serratia marcescens, an average of 5.28 log(10) CFU remained on each hand after washing, and 2.23 log(10) CFU was transferred to an agar surface. In an elementary-school-based field study, Gram-negative bacteria on the hands of students and staff increased by 1.42 log(10) CFU per hand (26-fold) after washing with soap from contaminated bulk-soap-refillable dispensers. In contrast, washing with soap from dispensers with sealed refills significantly reduced bacteria on hands by 0.30 log(10) CFU per hand (2-fold). Additionally, the mean number of Gram-negative bacteria transferred to surfaces after washing with soap from dispensers with sealed-soap refills (0.06 log(10) CFU) was significantly lower than the mean number after washing with contaminated bulk-soap-refillable dispensers (0.74 log(10) CFU; P soap (P soap from bulk-soap-refillable dispensers can increase the number of opportunistic pathogens on the hands and may play a role in the transmission of bacteria in public settings.

Environmental contaminants of emerging concern in seafood – European database on contaminant levels

International Nuclear Information System (INIS)

Vandermeersch, Griet; Lourenço, Helena Maria; Alvarez-Muñoz, Diana; Cunha, Sara; Diogène, Jorge; Cano-Sancho, German; Sloth, Jens J.; Kwadijk, Christiaan; Barcelo, Damia; Allegaert, Wim; Bekaert, Karen; Fernandes, José Oliveira; Marques, Antonio

2015-01-01

Marine pollution gives rise to concern not only about the environment itself but also about the impact on food safety and consequently on public health. European authorities and consumers have therefore become increasingly worried about the transfer of contaminants from the marine environment to seafood. So-called “contaminants of emerging concern” are chemical substances for which no maximum levels have been laid down in EU legislation, or substances for which maximum levels have been provided but which require revision. Adequate information on their presence in seafood is often lacking and thus potential risks cannot be excluded. Assessment of food safety issues related to these contaminants has thus become urgent and imperative. A database ( (www.ecsafeseafooddbase.eu)), containing available information on the levels of contaminants of emerging concern in seafood and providing the most recent data to scientists and regulatory authorities, was developed. The present paper reviews a selection of contaminants of emerging concern in seafood including toxic elements, endocrine disruptors, brominated flame retardants, pharmaceuticals and personal care products, polycyclic aromatic hydrocarbons and derivatives, microplastics and marine toxins. Current status on the knowledge of human exposure, toxicity and legislation are briefly presented and the outcome from scientific publications reporting on the levels of these compounds in seafood is presented and discussed. - Highlights: • Development of a European database regarding contaminants of emerging concern. • Current status on knowledge of human exposure, toxicity and legislation. • Review on the occurrence of contaminants of emerging concern in seafood.

Environmental contaminants of emerging concern in seafood – European database on contaminant levels

Energy Technology Data Exchange (ETDEWEB)

Vandermeersch, Griet, E-mail: griet.vandermeersch@ilvo.vlaanderen.be [Institute for Agricultural and Fisheries Research (ILVO), Animal Sciences Unit – Fisheries, Ankerstraat 1, 8400 Oostende (Belgium); Lourenço, Helena Maria [Division of Aquaculture and Upgrading (DivAV), Portuguese Institute for the Sea and Atmosphere (IPMA), Lisboa (Portugal); Alvarez-Muñoz, Diana [Catalan Institute for Water Research (ICRA), Girona (Spain); Cunha, Sara [LAQV-REQUIMTE, Laboratory of Bromatology and Hydrology, Faculty of Pharmacy, University of Porto, Rua Jorge de Viterbo Ferreira 228, 4050-313 Porto (Portugal); Diogène, Jorge [Institute of Research and Technology in Food and Agriculture (IRTA), Sant Carles de la Ràpita (Spain); Cano-Sancho, German [Laboratory of Toxicology and Environmental Health, School of Medicine, Rovirai Virgili University (URV), Reus (Spain); Sloth, Jens J. [National Food Institute, Technical University of Denmark (DTU Food), Søborg (Denmark); Kwadijk, Christiaan [Institute for Marine Resources and Ecosystem Studies (IMARES), Wageningen University and Research Center, Ijmuiden (Netherlands); Barcelo, Damia [Catalan Institute for Water Research (ICRA), Girona (Spain); Water and Soil Quality Research Group, Department of Environmental Chemistry, IDAEA-CSIC, Barcelona (Spain); Allegaert, Wim; Bekaert, Karen [Institute for Agricultural and Fisheries Research (ILVO), Animal Sciences Unit – Fisheries, Ankerstraat 1, 8400 Oostende (Belgium); Fernandes, José Oliveira [LAQV-REQUIMTE, Laboratory of Bromatology and Hydrology, Faculty of Pharmacy, University of Porto, Rua Jorge de Viterbo Ferreira 228, 4050-313 Porto (Portugal); Marques, Antonio [Division of Aquaculture and Upgrading (DivAV), Portuguese Institute for the Sea and Atmosphere (IPMA), Lisboa (Portugal); and others

2015-11-15

Marine pollution gives rise to concern not only about the environment itself but also about the impact on food safety and consequently on public health. European authorities and consumers have therefore become increasingly worried about the transfer of contaminants from the marine environment to seafood. So-called “contaminants of emerging concern” are chemical substances for which no maximum levels have been laid down in EU legislation, or substances for which maximum levels have been provided but which require revision. Adequate information on their presence in seafood is often lacking and thus potential risks cannot be excluded. Assessment of food safety issues related to these contaminants has thus become urgent and imperative. A database ( (www.ecsafeseafooddbase.eu)), containing available information on the levels of contaminants of emerging concern in seafood and providing the most recent data to scientists and regulatory authorities, was developed. The present paper reviews a selection of contaminants of emerging concern in seafood including toxic elements, endocrine disruptors, brominated flame retardants, pharmaceuticals and personal care products, polycyclic aromatic hydrocarbons and derivatives, microplastics and marine toxins. Current status on the knowledge of human exposure, toxicity and legislation are briefly presented and the outcome from scientific publications reporting on the levels of these compounds in seafood is presented and discussed. - Highlights: • Development of a European database regarding contaminants of emerging concern. • Current status on knowledge of human exposure, toxicity and legislation. • Review on the occurrence of contaminants of emerging concern in seafood.

Contamination Control: a systems approach

NARCIS (Netherlands)

Donck, J.C.J. van der

2010-01-01

Contamination influences a wide variety of industrial processes. For complex systems, contamination control, the collective effort to control contamination to such a level that it guarantees or even improves process or product functionality, offers a way for finding workable solutions. Central in

Center for Contaminated Sediments

Data.gov (United States)

Federal Laboratory Consortium — The U.S. Army Corps of Engineers Center for Contaminated Sediments serves as a clearinghouse for technology and expertise concerned with contaminated sediments. The...

Mental contamination: The effects of religiosity.

Science.gov (United States)

Bilekli, Ilgun; Inozu, Mujgan

2018-03-01

Mental contamination, which occurs in the absence of contact with a contaminant, has a moral element. Previous studies evoked feelings of mental contamination via listening to a scenario, which described a non-consensual kiss. Since mental contamination has a moral element, we tested the effects of the level of religiosity on feelings of mental contamination and related variables in an experimental design. Female undergraduates of high religiosity (n = 48) and low religiosity (n = 44) were randomly assigned to listen to one of two audio recordings involving a consensual or non-consensual kiss from a man described as moral. Mental contamination feelings were evoked successfully in both groups. Effects of scenario condition and religiosity level were seen in mental contamination and related negative feelings. Participants who imagined a non-consensual kiss reported greatest feelings of mental contamination, and internal and external negative feelings. More importantly, high religiosity resulted in greater feelings of mental contamination, internal negative feelings, as well as urges to wash and actual washing behaviors. The current study was conducted on non-clinical Muslim females. This limits the generalization of the findings to the wider population. Mental contamination and related feelings can be seen in different forms at different levels of religiosity. Copyright © 2017 Elsevier Ltd. All rights reserved.

Resuspended contaminated sediments cause sublethal stress to oysters: A biomarker differentiates total suspended solids and contaminant effects.

Science.gov (United States)

Edge, Katelyn J; Dafforn, Katherine A; Simpson, Stuart L; Ringwood, Amy H; Johnston, Emma L

2015-06-01

Resuspended contaminated sediments represent an important route of contaminant exposure for aquatic organisms. During resuspension events, filter-feeding organisms are exposed to contaminants, in both the dissolved form (at the gills) and the particulate form (in the digestive system). In addition, these organisms must manage the physical stress associated with an increase in total suspended solids (TSS). To date, few studies have experimentally compared the contributions to biological stress of contaminated and clean suspended solids. The authors mixed field-collected sediments (cellular biomarkers (lysosomal membrane stability, lipid peroxidation, and glutathione) were measured to evaluate sublethal toxicity. Lysosomal membrane stability was the most sensitive biomarker for distinguishing effects from resuspended contaminated sediments, as increasing amounts of contaminated TSS increased lysosomal membrane destabilization. The authors' results illustrate the importance of considering contaminant exposures from resuspended sediments when assessing the toxicity of contaminants to aquatic organisms. © 2015 SETAC.

Cleanup of contaminated areas

International Nuclear Information System (INIS)

Beone, G.; Carbone, A.I.; Zagaroli, M.

1989-01-01

The paper deals with the problem of contaminated areas cleanup, in order to eliminate every possible damage for man safety and environment and to site recovery for some utilization, The first step of cleanup operation is site characterization, that is followed by a pianificazion activity for a better definition of staff qualification, technology to be used, protection and prevention instruments for the risks due to contaminants handling. The second section describes the different remedial technologies for contaminated sites. Remedial technologies may be divided into on-site/off-site and in-situ treatments, according to whether materials (waste, soil, water) are moved to another location or not, respectively. Finally, it is outlined that contaminated areas cleanup is a typical multidisciplinary activity because very different competences are required. (author)

NSF-RANN trace contaminants abstracts

International Nuclear Information System (INIS)

Copenhaver, E.D.; Harnden, D.S.

1976-10-01

Specific areas of interest of the Environmental Aspects of Trace Contaminants Program are organic chemicals of commerce, metals and organometallic compounds, air-borne contaminants, and environmental assay methodology. Fifty-three abstracts of literature on trace contaminants are presented. Author, keyword, and permuted title indexes are included

Molds contamination of raw milk and dairy products: Occurrence, diversity and contamination source

Directory of Open Access Journals (Sweden)

T Moshtaghi Maleki

2015-11-01

Full Text Available This study aimed to assess the occurrence and diversity of mold species in raw milk and its products along with the identification of potential contamination sources. For this reason, a total of 260 samples consisting of 80 raw milk, 100 dairy products (i.e., pasteurized milk, yoghurt, cheese and buttermilk and 80 environmental (i.e. ingredients, packaging materials, surface of processing equipments and air specimens were collected. Using culture assay and microscopic observation, the occurrence as well as the diversity of mold species was investigated. According to the results, 82.3% of the samples were identified as positive for mold contamination. The percentage of mold contamination for raw milk was estimated as 97.5%. In the case of pasteurized milk, yoghurt, buttermilk, cheese and environmental samples, it was determined as 52%, 76%, 52%, 56% and 96.25%, respectively. Mold diversity among various samples consisted of Aspergillus, Geotrichum, Penicillium, Mucor, Alternaria, Rhizopus, Stemphylium, Cladosporium, and Fusarium. Results revealed a significant (p < 0.01 correlation between kind of mold species isolated from raw milk and dairy products. Similarly, a correlation was observed between dairy products and environmental sources. Regarding the high occurrence of mold contamination in raw milk and environmental sources, it seems that in some instances heat treatment was not effective enough to inactivate all molds; whereas in some other cases, cross contamination may have resulted in mold contamination. Therefore, it is crucial to maintain hygienic conditions during raw milk handling as well as processing steps. These practices could efficiently reduce the occurrence of mold contaminations in dairy products.

Microbial contaminants in Pakistan: a review

Directory of Open Access Journals (Sweden)

Maida Kanwal

2016-04-01

Full Text Available Worldwide contamination of surface waters with microbial pathogens is of substantial health concern. These contaminants are usually transmitted by improper sanitation measures, unsafe waste disposal, excretions from patients, and physical contacts, i.e., sexual and nonsexual. Majority of these microbial pathogens have been categorized into three classes, i.e., bacteria, viruses and protozoa. Pakistan, being a developing country, is facing a noteworthy threat due to microbial contamination. In Pakistan, bacterial contaminants are reported extensively followed by viral and protozoa contaminants. The health issues associated with bacterial population includes dysentery, abdominal pain, headache, diarrhea etc.; and usually includes faecal and total coliforms, E. coli, Salmonella, Shigella and Campylobacter. The cases related to viral contamination are lesser but chronic and evidenced the presence of HCV, HAV, HEV viruses causing hepatitis, and other hepatic disorders. Lastly, the health impacts associated with protozoans are least reported; and a number of diseases such as giardia, cryptosporidium and toxoplasma have been linked with this class of contaminants. The current review compiles information of these biological contaminants along with their health issues in Pakistan. Moreover, potential sources and fate of microbial contaminants are also discussed.

Contamination Control Techniques

Energy Technology Data Exchange (ETDEWEB)

EBY, J.L.

2000-05-16

Welcome to a workshop on contamination Control techniques. This work shop is designed for about two hours. Attendee participation is encouraged during the workshop. We will address different topics within contamination control techniques; present processes, products and equipment used here at Hanford and then open the floor to you, the attendees for your input on the topics.

Contamination Control Techniques

International Nuclear Information System (INIS)

EBY, J.L.

2000-01-01

Welcome to a workshop on contamination Control techniques. This work shop is designed for about two hours. Attendee participation is encouraged during the workshop. We will address different topics within contamination control techniques; present processes, products and equipment used here at Hanford and then open the floor to you, the attendees for your input on the topics

Contaminated Sites in Iowa

Data.gov (United States)

Iowa State University GIS Support and Research Facility — Sites contaminated by hazardous materials or wastes. These sites are those administered by the Contaminated Sites Section of Iowa DNR. Many are sites which are...

Technologies for remediating radioactively contaminated land

International Nuclear Information System (INIS)

Pearl, M.

2000-01-01

This paper gives an overview of technologies that can be used for the remediation of radioactively contaminated ground. There are a wide variety of techniques available -most have established track records for contaminated ground, though in general many are only just being adapted to use for radioactively contaminated ground. 1) Remediation techniques for radioactively contaminated ground involve either removal of the contamination and transfer to a controlled/contained facility such as the national LLW repository at Drigg, or 2) immobilization, solidification and stabilization of the contamination where the physical nature of the soil is changed, or an 'agent' is added to the soil, to reduce the migration of the contaminants, or 3) isolation and containment of the contaminated ground to reduce contaminant migration and control potential detrimental effects to human health. Where contamination has to be removed, ex situ and in situ techniques are available which minimize the waste requiring disposal to an LLW repository. These techniques include: 1) detector-based segregation 2) soil washing by particle separations 3) oil washing with chemical leaching agents 4) electro remediation 5) phyto remediation. Although many technologies are potentially applicable, their application to the remediation of a specific contaminated site is dependent on a number of factors and related to detailed site characterization studies, results from development trials and BPEO (best practicable environmental option) studies. Those factors considered of particular importance are: 1) the clean-up target 2) technical feasibility relative to the particular site, soil and contaminant characteristics, and time frame 3) site infrastructure arrangements and needs, the working life of the site and the duration of institutional care 4) long-term monitoring arrangements for slow remedial techniques or for immobilization and containment techniques 5) validation of the remediation 6) health and

Chemical barriers for controlling groundwater contamination

International Nuclear Information System (INIS)

Morrison, S.J.; Spangler, R.R.

1993-01-01

Chemical barriers are being explored as a low-cost means of controlling groundwater contamination. The barrier can intercept a contaminant plume and prevent migration by transferring contaminants from the groundwater to immobile solids. A chemical barrier can be emplaced in a landfill liner or in an aquifer cutoff wall or can be injected into a contaminant plume. Chemical barriers can be classified as either precipitation barriers or sorption barriers depending upon the dominant mode of contaminant extraction. In a precipitation barrier, contaminants are bound in the structures of newly formed phases; whereas, in a sorption barrier, contaminants attach to the surfaces of preexisting solids by adsorption or some other surface mechanism. Sorption of contaminants is pH dependent. A precipitation barrier can control the pH of the system, but alkaline groundwater may dominate the pH in a sorption barrier. A comparison is made of the characteristics of precipitation and sorption barriers. Experimental data on the extraction of uranium and molybdenum from simulated groundwater are used to demonstrate these concepts. 10 refs., 9 figs., 1 tab

Status on contamination monitoring in China

Energy Technology Data Exchange (ETDEWEB)

Quanlu, Gou [China Institute for Radiation Protection, Taiyuan (China)

1997-06-01

The air contaminated by radioactive materials in nuclear enterprises and radioactive workplaces and forming radioactive aerosol and the leakage of radioactive materials in operation cause internal exposure damage in workers. It is necessary and important to monitor air and surface contaminations for the health of public and workers, and for protecting environment. At present, many institutes engage in the studies on surface contamination monitoring in China, and the government has formulated the control limits of surface contamination in the Regulations of Radiation Protection. The monitors for surface contamination monitoring are almost home-made. The methods being used often are smear test and placing surface sample test. Scintillation counters, semiconductor detectors and G-M counters have been used for detecting alpha surface contamination. Plastic scintillator meters and thin wall/window G-M counters are used for beta surface contamination. Special detectors have been designed for monitoring low energy nuclides. The status of airborne contamination monitoring in China is reported. As the studies for future, the development of the surface contamination monitor for low energy beta nuclides, especially H-3, the monitoring methods for the special shapes of surfaces, the technology of decontamination and the calibration method and device for on-line radioactive aerosol continuous monitors are taken up. (K.I.)

Bacterial Hand Contamination and Transfer after Use of Contaminated Bulk-Soap-Refillable Dispensers▿†

Science.gov (United States)

Zapka, Carrie A.; Campbell, Esther J.; Maxwell, Sheri L.; Gerba, Charles P.; Dolan, Michael J.; Arbogast, James W.; Macinga, David R.

2011-01-01

Bulk-soap-refillable dispensers are prone to extrinsic bacterial contamination, and recent studies demonstrated that approximately one in four dispensers in public restrooms are contaminated. The purpose of this study was to quantify bacterial hand contamination and transfer after use of contaminated soap under controlled laboratory and in-use conditions in a community setting. Under laboratory conditions using liquid soap experimentally contaminated with 7.51 log10 CFU/ml of Serratia marcescens, an average of 5.28 log10 CFU remained on each hand after washing, and 2.23 log10 CFU was transferred to an agar surface. In an elementary-school-based field study, Gram-negative bacteria on the hands of students and staff increased by 1.42 log10 CFU per hand (26-fold) after washing with soap from contaminated bulk-soap-refillable dispensers. In contrast, washing with soap from dispensers with sealed refills significantly reduced bacteria on hands by 0.30 log10 CFU per hand (2-fold). Additionally, the mean number of Gram-negative bacteria transferred to surfaces after washing with soap from dispensers with sealed-soap refills (0.06 log10 CFU) was significantly lower than the mean number after washing with contaminated bulk-soap-refillable dispensers (0.74 log10 CFU; P soap (P soap from bulk-soap-refillable dispensers can increase the number of opportunistic pathogens on the hands and may play a role in the transmission of bacteria in public settings. PMID:21421792

Auburn Steel Company radioactive contamination incident

International Nuclear Information System (INIS)

Bradley, F.J.; Cabasino, L.; Kelly, R.; Awai, A.; Kasyk, G.

1986-04-01

On February 21, 1983, workers at the Auburn Steel Company, Auburn, New York discovered that about 120 tons of steel poured that day had become contaminated with 60 Co. In addition to the steel, the air cleaning system and portions of the mill used in casting the steel were contaminated. Approximately 25 curies of 60 Co were involved. Decontamination and disposal of the contamination cost in excess of $2,200,000. This report details the discovery of the contamination, decontamination of the plant and disposal of the contamination

Contamination Effects Due to Space Environmental Interactions

Science.gov (United States)

Chen, Philip T.; Paquin, Krista C. (Technical Monitor)

2001-01-01

Molecular and particulate contaminants are commonly generated from the orbital spacecraft operations that are under the influence of the space environment. Once generated, these contaminants may attach to the surfaces of the spacecraft or may remain in the vicinity of the spacecraft. In the event these contaminants come to rest on the surfaces of the spacecraft or situated in the line-of-sight of the observation path, they will create various degrees of contamination effect which may cause undesirable effects for normal spacecraft operations, There will be circumstances in which the spacecraft may be subjected to special space environment due to operational conditions. Interactions between contaminants and special space environment may alter or greatly increase the contamination effect due to the synergistic effect. This paper will address the various types of contamination generation on orbit, the general effects of the contamination on spacecraft systems, and the typical impacts on the spacecraft operations due to the contamination effect. In addition, this paper will explain the contamination effect induced by the space environment and will discuss the intensified contamination effect resulting from the synergistic effect with the special space environment.

Direct probability mapping of contaminants

International Nuclear Information System (INIS)

Rautman, C.A.

1993-01-01

Exhaustive characterization of a contaminated site is a physical and practical impossibility. Descriptions of the nature, extent, and level of contamination, as well as decisions regarding proposed remediation activities, must be made in a state of uncertainty based upon limited physical sampling. Geostatistical simulation provides powerful tools for investigating contaminant levels, and in particular, for identifying and using the spatial interrelationships among a set of isolated sample values. This additional information can be used to assess the likelihood of encountering contamination at unsampled locations and to evaluate the risk associated with decisions to remediate or not to remediate specific regions within a site. Past operation of the DOE Feed Materials Production Center has contaminated a site near Fernald, Ohio, with natural uranium. Soil geochemical data have been collected as part of the Uranium-in-Soils Integrated Demonstration Project. These data have been used to construct a number of stochastic images of potential contamination for parcels approximately the size of a selective remediation unit. Each such image accurately reflects the actual measured sample values, and reproduces the univariate statistics and spatial character of the extant data. Post-processing of a large number of these equally likely, statistically similar images produces maps directly showing the probability of exceeding specified levels of contamination. Evaluation of the geostatistical simulations can yield maps representing the expected magnitude of the contamination for various regions and other information that may be important in determining a suitable remediation process or in sizing equipment to accomplish the restoration

Airborne radioactive contamination following aerosol ventilation studies

International Nuclear Information System (INIS)

Mackie, A.; Hart, G.C.; Ibbett, D.A.; Whitehead, R.J.S.

1994-01-01

Lung aerosol ventilation studies may be accompanied by airborne contamination, with subsequent surface contamination. Airborne contamination has been measured prior to, during and following 59 consecutive 99 Tc m -diethylenetriamine pentaacetate (DTPA) aerosol studies using a personal air sampler. Airborne contamination ranging between 0 and 20 330 kBq m -3 has been measured. Airborne contamination increases with degree of patient breathing difficulty. The effective dose equivalent (EDE) to staff from ingested activity has been calculated to be 0.3 μSv per study. This figure is supported by data from gamma camera images of a contaminated staff member. However, surface contamination measurements reveal that 60% of studies exceed maximum permissible contamination limits for the hands; 16% of studies exceed limits for controlled area surfaces. (author)

Safety against radioactive contamination

International Nuclear Information System (INIS)

Anon.

1983-01-01

The ALWIT anticontamination suit is briefly described, consisting of lasting antistatic ''NDMEX III''. It was specially developed for the fire brigade who are exposed to a particular kind of contamination while carrying out radiation measurements during fire fighting, rescue and clearing up work. The ALWIT suit reliably prevents radioactive contamination of the surface of the body while wearing a breathing apparatus, independent of the ambient air. Tightly fitting cuffs on the neck, arms and legs together with zippers placed behind prevent contamination even with extreme movement. (P.F.K.)

Groundwater contamination and community relations

International Nuclear Information System (INIS)

Hayes, K.

2004-01-01

Westinghouse Electric Company LLC ('Westinghouse') acquired a nuclear fuel processing plant at Hematite, Missouri ('Hematite', the 'Facility', or the 'Plant') in April 2000. The plant has subsequently been closed, and its operations have been relocated to a newer, larger facility. Westinghouse has announced plans to complete its clean-up, decommissioning, and License retirement in a safe, socially responsible, and environmentally sound manner as required by internal policies, as well as those of its parent company, British Nuclear Fuels plc. (BNFL). Preliminary investigations have revealed the presence of environmental contamination in various areas of the facility and grounds, including both radioactive contamination and various other substances related to the nuclear fuel processing operations. Most noteworthy among the areas of contamination are seven private drinking water wells up to 3 000 feet to the southeast, and one private drinking water well approximately 1 000 feet to the northeast, that have been found to contain tetra-chloro-ethylene ('PCE'), trichloroethylene ('TCE'), and other contaminants associated with their environmental degradation. Potential sources of this contamination include approximately 40 large unlined on-site burial pits and 2 evaporation ponds in which previous operators of the facility disposed of uranium contaminated wastes and a variety of other hazardous substances. This paper discusses Westinghouse's response to the discovery of drinking water contamination, and the significance of its community relations program within that response. (author)

Dispersion of Contaminants in Indoor Climate

DEFF Research Database (Denmark)

Heiselberg, Per

In rooms ventilated by mixing ventilation, in order to remove contaminants from the occupied zone, the goal of the air distribution system is to achieve a low and even concentration distribution in the room. The experiments showed that the contaminant distribution in a room always will depend...... on the location of the contamination source and in practice also on the supplied air flow rate and the contaminant density. The results showed that it is important for the removal of contaminants in a room that the ventilation system is working in the same direction as the existing buoyancy forces....

The Contaminant Cobweb

DEFF Research Database (Denmark)

Bech Albertsen, Anita Nell

2017-01-01

This article maps out character complexity in Penny Dreadful by focusing on the intertextuality of monstrous female characters. The aim of this study is twofold. First, it seeks to examine show how mashup characters gain complexity through textual contamination as they are woven into an intertext......This article maps out character complexity in Penny Dreadful by focusing on the intertextuality of monstrous female characters. The aim of this study is twofold. First, it seeks to examine show how mashup characters gain complexity through textual contamination as they are woven...... into an intertextual cobweb of signification. Secondly, it aims at examining how monstrous complex characters like Vanessa Ives can be conceived as mashups contaminated by different manifestations of the monstrous-feminine as coined by Barbara Creed. An overarching hypothesis of this study is that interfigural...

Drinking Water Contaminants -- Standards and Regulations

Science.gov (United States)

... and Research Centers Contact Us Share Drinking Water Contaminants – Standards and Regulations EPA identifies contaminants to regulate ... other partners to implement these SDWA provisions. Regulated Contaminants National Primary Drinking Water Regulations (NPDWRs) - table of ...

Balancing the risks of habitat alteration and environmental contamination in a contaminated forested wetland

International Nuclear Information System (INIS)

Bleiler, J.A.; Daukas, G.; Richardson, N.

1994-01-01

The North Lawrence Oil Dump Site (NLODS) is an inactive hazardous waste site located adjacent to an extensive palustrine forested wetland in upstate New York. Waste oil and oil sludge were disposed of in a lagoon adjacent to the wetland during the 1960s. During periods of high water, oils escaped from the lagoon and were transported into the wetlands. High concentrations of lead and PCBs were detected in NLODS wetland sediments, and contaminants from the site were present in wetland's plant and animal tissues. However, contaminated portions of the wetlands appear to be physically undisturbed and provide high quality wildlife habitat. The results of an ecological risk assessment indicated that lead and PCB contamination in NLODS sediment may be impacting some components of the wetlands community. The risk management process considered both the toxicological risks associated with lead and PCB contamination, as well as the significant habitat destruction risks associated with remediation. Six potential PCB target cleanup levels were evaluated. Following removal of sediments with PCB contamination greater than 0.5 mg/kg, 3.5 acres of sediment with lead contamination in excess of 250 mg/kg (the New York State ''Severe Effect Level'') would remain. More than 1.5 of these acres would contain lead concentrations in excess of 1,000 mg/kg. Reducing lead levels to background concentrations would require more than 50 acres of wetlands alteration. The Record of Decision at the NLODS recognized the high quality habitat provided by the site's wetlands, and attempted to balance the risks from habitat alteration with the risks of environmental contamination

Environmental contaminants of emerging concern in seafood--European database on contaminant levels.

Science.gov (United States)

Vandermeersch, Griet; Lourenço, Helena Maria; Alvarez-Muñoz, Diana; Cunha, Sara; Diogène, Jorge; Cano-Sancho, German; Sloth, Jens J; Kwadijk, Christiaan; Barcelo, Damia; Allegaert, Wim; Bekaert, Karen; Fernandes, José Oliveira; Marques, Antonio; Robbens, Johan

2015-11-01

Marine pollution gives rise to concern not only about the environment itself but also about the impact on food safety and consequently on public health. European authorities and consumers have therefore become increasingly worried about the transfer of contaminants from the marine environment to seafood. So-called "contaminants of emerging concern" are chemical substances for which no maximum levels have been laid down in EU legislation, or substances for which maximum levels have been provided but which require revision. Adequate information on their presence in seafood is often lacking and thus potential risks cannot be excluded. Assessment of food safety issues related to these contaminants has thus become urgent and imperative. A database (www.ecsafeseafooddbase.eu), containing available information on the levels of contaminants of emerging concern in seafood and providing the most recent data to scientists and regulatory authorities, was developed. The present paper reviews a selection of contaminants of emerging concern in seafood including toxic elements, endocrine disruptors, brominated flame retardants, pharmaceuticals and personal care products, polycyclic aromatic hydrocarbons and derivatives, microplastics and marine toxins. Current status on the knowledge of human exposure, toxicity and legislation are briefly presented and the outcome from scientific publications reporting on the levels of these compounds in seafood is presented and discussed. Copyright © 2015 Elsevier Inc. All rights reserved.

Rehabilitation of radioactive contaminated forests

International Nuclear Information System (INIS)

Panfilov, A.V.; Uspenskaya, E.Ju.

2002-01-01

As a result of radiation accidents and nuclear-weapon tests at the territory of the former USSR a part of the Forest Fund of 23 subjects of the Russian Federation has been contaminated by radionuclides. The contaminated forests, which are included in a structure of more than 130 forest management units (leskhozes) and more then 330 local forest management units, as a rule, are located in highly inhabited regions with traditionally intensive forestry management and high level of forest resources use. To provide radiologically safe forest management in the contaminated areas, the Federal Forest Service has developed and validated a special system of countermeasures. Use of this system makes it possible to diminish significantly the dose to personnel, to exclude the use of forest products with contamination exceeding radiological standards and to provide protection of the forest as a biogeochemical barrier to radionuclide migration from contaminated areas to human habitat. (author)

77 FR 27057 - Request for Nominations of Drinking Water Contaminants for the Fourth Contaminant Candidate List

Science.gov (United States)

2012-05-08

... captures emerging chemicals and pathogens. D. Why is EPA soliciting contaminant nominations? EPA is... providing an additional pathway for the public to identify new and emerging contaminants that may not be... new and emerging contaminants that might not otherwise be considered because new information has not...

Process for the separation of contaminant or mixture of contaminants from a Ch4-comprising gaseous feed streem

NARCIS (Netherlands)

2012-01-01

The invention provides a process for the separation of a contaminant or mixture of contaminants from a CH4-comprising gaseous feed streem, comprising the subsequent steps of: a) passing a CH4-comprising gaseous feed streem comprising the contaminant or the mixture of contaminants in to and through a

Contaminated soil concrete blocks

NARCIS (Netherlands)

de Korte, A.C.J.; Brouwers, Jos; Limbachiya, Mukesh C.; Kew, Hsein Y.

2009-01-01

According to Dutch law the contaminated soil needs to be remediated or immobilised. The main focus in this article is the design of concrete blocks, containing contaminated soil, that are suitable for large production, financial feasible and meets all technical and environmental requirements. In

Monitoring of surface and airborne contamination

Energy Technology Data Exchange (ETDEWEB)

Pradeep Kumar, K S [Bhabha Atomic Research Centre, Bombay (India)

1997-06-01

Indian nuclear energy programme aims at total safety in all activities involved in the entire fuel cycle for the occupational workers, members of the public and the environment as a whole. Routine radiation monitoring with clearly laid out procedures are followed for ensuring the safety of workers and public. Radiation monitoring carried out for the nuclear installations comprises of process monitoring, monitoring of effluent releases and also of the radiation protection monitoring of the individuals, work place and environment. Regulations like banning of smoking and consumption of food and drink etc. reduces the risk of direct ingestion even if inadvertent spread of contamination takes place. Though limit of transportable surface contamination is prescribed, the health physicists always follow a ``clean on swipe`` philosophy which compensates any error in the measurement of surface contamination. In this paper, the following items are contained: Necessity of contamination monitoring, accuracy required in the calibration of surface contamination monitors, methodology for contamination monitoring, air monitoring, guidelines for unrestricted release of scrap materials, and problems in contamination monitoring. (G.K.)

Radioactive contamination incidents involving protective clothing

International Nuclear Information System (INIS)

Reichelt, R.A.; Clay, M.E.; Eichorst, A.J.

1998-01-01

The study focuses on incidents at Department of Energy facilities involving the migration of radioactive contaminants through protective clothing. The authors analyzed 68 occurrence reports for the following factors: (1) type of work, (2) working conditions, (3) type of anti-contamination material; (4) area of body or clothing contaminated; and (5) nature of spread of contamination. A majority of reports identified strenuous work activities such as maintenance, construction, or decontamination and decommissioning projects. The reports also indicated adverse working conditions that included hot and humid or cramped work environments. The type of anti-contamination clothing most often identified was cotton or water-resistant disposable clothing. Most of the reports also indicated contaminants migrating through perspiration-soaked areas, typically in the knees and forearms. On the basis of their survey, the authors recommend the use of improved engineering controls and resilient, breathable, waterproof protective clothing for work in hot, humid, or damp areas where the possibility of prolonged contact with contamination cannot be easily avoided or controlled. 1 ref., 6 figs., 1 tab

Evaluation of Unfixed Tritium Surface Contamination

International Nuclear Information System (INIS)

Postolache, C.; Matei, Lidia

2005-01-01

Surface unfixed radioactive contamination represents the amount of surface total radioactive contamination which can be eliminated by pure mechanical processes. This unfixed contamination represents the main risk factor for contamination of the personnel which operates in tritium laboratories. Unfixed contamination was determined using sampling smears type FPCSN-PSE-AA. Those FPCSN-PSE-AA smears are disks of expanded polystyrene which contain acrylic acid fragments superficially grafted. Sampling factor was determinated by contaminated surface wiping with moisten smears in 50 μL butylic alcohol and activity measuring at liquid scintillation measuring device. Sampling factor was determined by the ratio between measured activity and initially real conventional activity. The sampling factor was determined for Tritium Laboratory existent surfaces: stainless steel, aluminum, glass, ceramics, linoleum, washable coats, epoxy resins type ALOREX LP-52.The sampling factors and the reproducibility were determined in function of surface nature

Evaluation of certain contaminants in food.

Science.gov (United States)

2017-01-01

This report represents the conclusions of a Joint FAO/WHO Expert Committee convened to evaluate the safety of various contaminants or groups of contaminants in food. The first part of the report contains a brief description of general considerations addressed at the meeting, including updates on matters of interest to the work of the Committee. A summary follows of the Committee’s evaluations of technical, toxicological and/or dietary exposure data for six contaminants or groups of contaminants (aflatoxins, 4,15-diacetoxyscirpenol, fumonisins, glycidyl esters, 3-MCPD esters and 3-MCPD, sterigmatocystin) as well as an evaluation of co-exposure of fumonisins with aflatoxins. Annexed to the report is a summary of the toxicological and dietary exposure information as well as the Committee’s recommendations on the contaminants and groups of contaminants considered at this meeting.

Separation of contaminated concrete

International Nuclear Information System (INIS)

Bakiewicz, J.L.; Reymer, A.P.S.

1990-01-01

Separating the contaminated parts from the non-contaminated parts from decommissioned nuclear facilities may strongly reduce the amount of contaminated concrete. The reduction in volume of the radioactive contaminated concrete is dependent on how much cementstone is in the concrete. This research program shows that the radioactive contamination is mostly in the cementstone. However the choice that the cementstone parts, (or better said the radioactive parts) are smaller than 1 mm may not always be true. Normally the cementstone takes about 30% of the total concrete volume. A separation procedure composed by a combination of milling and thermal shock has been assessed. Both the cold and hot thermal shock in combination with milling are not able to separate the cementstone from the larger aggregates completely. However, the cementstone from the concrete with a low nominal grain size seems to be almost completely removed by the combination cold thermal shock/milling, while the cementstone from the concrete with a high nominal grain size seems to be almost completely removed by the combination hot thermal shock/milling. After both methods a layer of cementstone was still visible on the aggregates. Washing followed by a nitric acid treatment removed each 2 wt% of cementstone

Chemical contaminants on DOE lands and selection of contaminant mixtures for subsurface science research

Energy Technology Data Exchange (ETDEWEB)

Riley, R.G.; Zachara, J.M. [Pacific Northwest Lab., Richland, WA (United States)

1992-04-01

This report identifies individual contaminants and contaminant mixtures that have been measured in the ground at 91 waste sites at 18 US Department of Energy (DOE) facilities within the weapons complex. The inventory of chemicals and mixtures was used to identify generic chemical mixtures to be used by DOE`s Subsurface Science Program in basic research on the subsurface geochemical and microbiological behavior of mixed contaminants (DOE 1990a and b). The generic mixtures contain specific radionuclides, metals, organic ligands, organic solvents, fuel hydrocarbons, and polychlorinated biphenyls (PCBs) in various binary and ternary combinations. The mixtures are representative of in-ground contaminant associations at DOE facilities that are likely to exhibit complex geochemical behavior as a result of intercontaminant reactions and/or microbiologic activity stimulated by organic substances. Use of the generic mixtures will focus research on important mixed contaminants that are likely to be long-term problems at DOE sites and that will require cleanup or remediation. The report provides information on the frequency of associations among different chemicals and compound classes at DOE waste sites that require remediation.

Modeling subsurface contamination at Fernald

International Nuclear Information System (INIS)

Jones, B.W.; Flinn, J.C.; Ruwe, P.R.

1994-01-01

The Department of Energy's Fernald site is located about 20 miles northwest of Cincinnati. Fernald produced refined uranium metal products from ores between 1953 and 1989. The pure uranium was sent to other DOE sites in South Carolina, Tennessee, Colorado,and Washington in support of the nation's strategic defense programs. Over the years of large-scale uranium production, contamination of the site's soil and groundwater occurred.The contamination is of particular concern because the Fernald site is located over the Great Miami Aquifer, a designated sole-source drinking water aquifer. Contamination of the aquifer with uranium was found beneath the site, and migration of the contamination had occurred well beyond the site's southern boundary. As a result, Fernald was placed on the National Priorities (CERCLA/Superfund) List in 1989. Uranium production at the site ended in 1989,and Fernald's mission has been changed to one of environmental restoration. This paper presents information about computerized modeling of subsurface contamination used for the environmental restoration project at Fernald

Forestry on the contamination territories

International Nuclear Information System (INIS)

Stavrov, A.I.; Kovalev, S.D.; Zhukovskaya, O.V.; Drobyshevskaya, N.M.

1995-01-01

The common characteristic of a contamination of the Belarus' forests by radionuclides after the Chernobyl accident is indicated. The recommendations for population about the picking up the mushrooms, berries, juices, medicinal herbs, preparation of forages, wood and other production in the contaminated forests are given. The information about the using of forests in depending on a level of the soil contamination is given. 5 refs., 1 tab., 4 figs

Skin contamination - prevention and decontaminating

International Nuclear Information System (INIS)

Henning, K.

2001-01-01

A detailed examination is made of the structure of human skin. Measures were drawn up to prevent skin contamination in nuclear installations as well as contaminated skin was decontaminated from the personnel. By systematically applying these measures a significant level of success was achieved in preventing contamination in nuclear installations. Cases where more far-reaching chemical methods had to be used were kept to a minimum. (R.P.)

Response of microbial activities and diversity to PAHs contamination at coal tar contaminated land

Science.gov (United States)

Zhao, Xiaohui; Sun, Yujiao; Ding, Aizhong; Zhang, Dan; Zhang, Dayi

2015-04-01

Coal tar is one of the most hazardous and concerned organic pollutants and the main hazards are polycyclic aromatic hydrocarbons (PAHs). The indigenous microorganisms in soils are capable to degrade PAHs, with essential roles in biochemical process for PAHs natural attenuation. This study investigated 48 soil samples (from 8 depths of 6 boreholes) in Beijing coking and chemistry plant (China) and revealed the correlation between PAHs contamination, soil enzyme activities and microbial community structure, by 16S rRNA denaturing gradient gel electrophoresis (DGGE). At the site, the key contaminants were identified as naphthalene, acenaphthylene, acenaphthene, fluorene, phenanthrene and anthracene, and the total PAHs concentration ranged from 0.1 to 923.9 mg/kg dry soil. The total PAHs contamination level was positively correlated (pcatalase activities (0.554-6.230 mL 0.02 M KMnO4/g•h) and dehydrogenase activities (1.9-30.4 TF μg/g•h soil), showing the significant response of microbial population and degrading functions to the organic contamination in soils. The PAHs contamination stimulated the PAHs degrading microbes and promoted their biochemical roles in situ. The positive relationship between bacteria count and dehydrogenase activities (p<0.05) suggested the dominancy of PAHs degrading bacteria in the microbial community. More interestingly, the microbial community deterioration was uncovered via the decline of microbial biodiversity (richness from 16S rRNA DGGE) against total PAHs concentration (p<0.05). Our research described the spatial profiles of PAHs contamination and soil microbial functions at the PAHs heavily contaminated sites, offering deeper understanding on the roles of indigenous microbial community in natural attenuation process.

Contaminated sediment transport during floods

International Nuclear Information System (INIS)

Fontaine, T.A.

1992-01-01

Over the past 48 years, operations and waste disposal activities at Oak Ridge National Laboratory have resulted in the contamination of parts of the White Oak Creek catchment. The contaminants presenting the highest risk to human health and the environment are particle reactive and are associated with the soils and sediments in the White Oak Creek drainage system. The erosion of these sediments during floods can result in the transport of contaminants both within the catchment and off-site into the Clinch River. A data collection program and a modeling investigation are being used to evaluate the probability of contaminated sediment transport during floods and to develop strategies for controlling off-site transport under present and future conditions

Development of remote operated floor contamination monitor

International Nuclear Information System (INIS)

Sreekumar, K.; Gangamohan, M.; Kannan, R.K.; Rajan, S.

2005-01-01

Contamination check of floors and walkways in and around Reactor building areas forms an integral part of Radiation Protection Program in Power Stations. Though random swipe check method is adopted for the detection of loose contamination, this method has the disadvantage of leaving the fixed contamination and hotspots undetected. Hence, scanning the area with a sensitive detector, held close to the surface provides positive means for the detection of contamination. Checking large areas and walkways by holding the detector close to the surface involves physical work. Also, areas which are unapproachable due to congestion of equipment, may go uncovered by contamination monitoring in order to eliminate the physical strain involved in such contamination monitoring and to cover unapproachable areas, a small size prototype device that can be operated remotely was fabricated. This device detects contamination instantaneously and accurately. This paper describes design and fabrication of the device used for floor contamination monitoring. (author)

Air contamination analysis during emergency medical treatment

International Nuclear Information System (INIS)

Yamada, Y.; Fukutsu, K.; Yuuki, M.; Akashi, M.

2009-01-01

After radiological emergencies, patients contaminated with radioactivity are taken to radiation emergency hospitals for treatment. Numerical simulations using the computer software 'Flow Designer R were made in order to evaluate indoor air contamination caused by the breathing out of contaminated air. The National Inst. of Radiological Sciences facility was used for the numerical evaluation. Results indicate that the dispersion of contaminated air depends on the characteristics of the contaminants, and that the dispersion range was limited and localised. Only medical staff standing in a special position near the patient was exposed to almost un-diluted contaminated air. Highly contaminated air was evacuated with a local exhaust pump system. Room air quality was monitored using a continuous air sampling system, but it was found that the sampling point was not representative for the purpose of radiation protection. From the air-flow analysis, some problems that affect radiological safety were revealed and valuable information and measures for preventing secondary contamination were determined. (authors)

Have we to harvest the contaminated wheats?

International Nuclear Information System (INIS)

Tannenberg, P. de

1997-01-01

The institute of nuclear protection and safety (IPSN) has just developed a calculation method allowing to evaluate the radioactive contamination of harvesting. This tool would allow, in case of nuclear accident, to determine if the contaminated lands under cultivation are eatable or not. Two radionuclides have been chosen: cesium 137 and strontium 90. The experiments are conclusive: the experimental releases of cesium and strontium were comparable to these ones of the Chernobyl forbidden zone (between 10 and 40 millions of becquerels/m 2 ): the foliar contamination is proportional to the plants development. Wheats ready to be harvested capture more than 80% of the radioactivity that contaminates them. Leaves of young plants keep only 20 to 40 %. Second result: cesium is more easily washable than strontium. Third results: more late is the contamination more the plant will be irradiated; then,the wheats contaminated when they are just out of ground are nine times less contaminated than cereals contaminated just before the harvest. (N.C.)

Contamination of broiler chickens with radiocaesium contaminated feed and its reduction

International Nuclear Information System (INIS)

Poeschl, M.

2004-01-01

The present study summarises information gleaned during investigations of the transfer of radiocaesium ( 137 Cs) and tests of countermeasures of a chemical character, i.e. feed additives limiting the transfer from the feed of broiler chicken. The regularities of the transport and distribution of radiocaesium in the organism (liver, kidneys, muscles, intestines) from feed were studied, including tests of the effect of the source of radiocaesium, date of administration and age of the chickens. The results confirmed that the retention of radiocaesium from feed into the body organs was very rapid (several hours) as was the release from the body (T 1/2b = 0.5-2 days) during the decontamination. Differences were discovered in the distribution and dynamics of the content of 137 Cs between breast and leg meat. The tests showed a very effective and relatively simple method of measuring the contaminated chickens in vivo. Special clay mineral or cellulose-based feed additives, and also modified hexacyanoferrates, especially when applied prior to contamination proper, considerably reduced the retention of radiocaesium into the breast and leg meat, and if the meat has already been contaminated, or if contamination was inevitable, the concentrations of 137 Cs in broiler chicken meat admissible for foodstuffs could be obtained much more quickly. (authors)

Bioremediation of PAH contaminated soil samples

International Nuclear Information System (INIS)

Joshi, M.M.; Lee, S.

1994-01-01

Soils contaminated with polynuclear aromatic hydrocarbons (PAHs) pose a hazard to life. The remediation of such sites can be done using physical, chemical, and biological treatment methods or a combination of them. It is of interest to study the decontamination of soil using bioremediation. The experiments were conducted using Acinetobacter (ATCC 31012) at room temperature without pH or temperature control. In the first series of experiments, contaminated soil samples obtained from Alberta Research Council were analyzed to determine the toxic contaminant and their composition in the soil. These samples were then treated using aerobic fermentation and removal efficiency for each contaminant was determined. In the second series of experiments, a single contaminant was used to prepare a synthetic soil sample. This sample of known composition was then treated using aerobic fermentation in continuously stirred flasks. In one set of flasks, contaminant was the only carbon source and in the other set, starch was an additional carbon source. In the third series of experiments, the synthetic contaminated soil sample was treated in continuously stirred flasks in the first set and in fixed bed in the second set and the removal efficiencies were compared. The removal efficiencies obtained indicated the extent of biodegradation for various contaminants, the effect of additional carbon source, and performance in fixed bed without external aeration

Subsurface Contamination Control

Energy Technology Data Exchange (ETDEWEB)

Y. Yuan

2001-12-12

There are two objectives of this report, ''Subsurface Contamination Control''. The first is to provide a technical basis for recommending limiting radioactive contamination levels (LRCL) on the external surfaces of waste packages (WP) for acceptance into the subsurface repository. The second is to provide an evaluation of the magnitude of potential releases from a defective WP and the detectability of the released contents. The technical basis for deriving LRCL has been established in ''Retrieval Equipment and Strategy for Wp on Pallet'' (CRWMS M and O 2000g, 6.3.1). This report updates the derivation by incorporating the latest design information of the subsurface repository for site recommendation. The derived LRCL on the external surface of WPs, therefore, supercede that described in CRWMS M and O 2000g. The derived LRCL represent the average concentrations of contamination on the external surfaces of each WP that must not be exceeded before the WP is to be transported to the subsurface facility for emplacement. The evaluation of potential releases is necessary to control the potential contamination of the subsurface repository and to detect prematurely failed WPs. The detection of failed WPs is required in order to provide reasonable assurance that the integrity of each WP is intact prior to MGR closure. An emplaced WP may become breached due to manufacturing defects or improper weld combined with failure to detect the defect, by corrosion, or by mechanical penetration due to accidents or rockfall conditions. The breached WP may release its gaseous and volatile radionuclide content to the subsurface environment and result in contaminating the subsurface facility. The scope of this analysis is limited to radioactive contaminants resulting from breached WPs during the preclosure period of the subsurface repository. This report: (1) documents a method for deriving LRCL on the external surfaces of WP for acceptance into the

A cleanroom contamination control system

OpenAIRE

Whyte, W.; Eaton, T.

2002-01-01

Analytical methods for hazard and risk analysis are being considered for controlling contamination\\ud in pharmaceutical cleanrooms. The most suitable method appears to be the HACCP system that has\\ud been developed for the food industry, but this requires some reinterpretation for use in\\ud pharmaceutical manufacturing. This paper suggests a possible system.\\ud To control contamination effectively, it is necessary to have a good appreciation of the routes and\\ud sources of contamination, and ...

49 CFR 175.705 - Radioactive contamination.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Radioactive contamination. 175.705 Section 175.705... Regulations Applicable According to Classification of Material § 175.705 Radioactive contamination. (a) A... (radioactive) materials that may have been released from their packagings. (b) When contamination is present or...

49 CFR 176.715 - Contamination control.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Contamination control. 176.715 Section 176.715... Requirements for Radioactive Materials § 176.715 Contamination control. Each hold, compartment, or deck area... the removable (non-fixed) radioactive surface contamination is not greater than the limits prescribed...

49 CFR 173.443 - Contamination control.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Contamination control. 173.443 Section 173.443... SHIPMENTS AND PACKAGINGS Class 7 (Radioactive) Materials § 173.443 Contamination control. (a) The level of non-fixed (removable) radioactive contamination on the external surfaces of each package offered for...

URINE CULTURE CONTAMINATION: A ONE-YEAR ...

African Journals Online (AJOL)

boaz

Background: Urine culture contamination is a significant cause of delay in treatment of patients being investigated for urinary tract infection. ... Lowest contamination rates were in Emergency Paediatric Unit (EPU) and intensive ... The female gender was found to be the most significant predictor of higher contamination rate.

A petroleum contaminated soil bioremediation facility

Energy Technology Data Exchange (ETDEWEB)

Lombard, K.; Hazen, T.

1994-06-01

The amount of petroleum contaminated soil (PCS) at the Savannah River site (SRS) that has been identified, excavated and is currently in storage has increased several fold during the last few years. Several factors have contributed to this problem: (1) South Carolina Department of Health ad Environmental control (SCDHEC) lowered the sanitary landfill maximum concentration for total petroleum hydrocarbons (TPH) in the soil from 500 to 100 parts per million (ppm), (2) removal and replacement of underground storage tanks at several sites, (3) most recently SCDHEC disallowed aeration for treatment of contaminated soil, and (4) discovery of several very large contaminated areas of soil associated with leaking underground storage tanks (LUST), leaking pipes, disposal areas, and spills. Thus, SRS has an urgent need to remediate large quantities of contaminated soil that are currently stockpiled and the anticipated contaminated soils to be generated from accidental spills. As long as we utilize petroleum based compounds at the site, we will continue to generate contaminated soil that will require remediation.

A petroleum contaminated soil bioremediation facility

International Nuclear Information System (INIS)

Lombard, K.; Hazen, T.

1994-01-01

The amount of petroleum contaminated soil (PCS) at the Savannah River site (SRS) that has been identified, excavated and is currently in storage has increased several fold during the last few years. Several factors have contributed to this problem: (1) South Carolina Department of Health ad Environmental control (SCDHEC) lowered the sanitary landfill maximum concentration for total petroleum hydrocarbons (TPH) in the soil from 500 to 100 parts per million (ppm), (2) removal and replacement of underground storage tanks at several sites, (3) most recently SCDHEC disallowed aeration for treatment of contaminated soil, and (4) discovery of several very large contaminated areas of soil associated with leaking underground storage tanks (LUST), leaking pipes, disposal areas, and spills. Thus, SRS has an urgent need to remediate large quantities of contaminated soil that are currently stockpiled and the anticipated contaminated soils to be generated from accidental spills. As long as we utilize petroleum based compounds at the site, we will continue to generate contaminated soil that will require remediation

Hand and foot contamination monitor

International Nuclear Information System (INIS)

Jakati, R.K.; Kaptral, R.S.; Ananthkrishnan, T.S.; Pansare, M.G.

1989-01-01

In order to make quick measurements of beta and gamma contaminations on hands and feet of personnel working in radioactive environments, hand and foot contamination monitors are widely used. This paper describes such a monitor system designed with Intel 8085 based microcomputer. The monitoring and warning system is designed to perform measurement of activity spread over surface of hands and soles of shoes or feet. Even though the system has many features to aid testing and maintainance operation, it is easy to use for unskilled persons. In order to check the contamination, the person stands on platform and inserts both his hands into detector assemblies thereby actuating the sensing switches. After a preset interval, annunciation of clean or contaminated status is declared by the system. (author)

Level of Campylobacter jejuni from naturally contaminated chicken liver and chicken legs in various task: a cross contamination study

Directory of Open Access Journals (Sweden)

New, C.Y.

2017-03-01

Full Text Available Cross contamination is one of the most important contributing factors in foodborne illness originating in household environments. The objective of this research was to determine the transfer between naturally contaminated chicken liver and leg to cutting board, hand glove, knife and cucumber, during slicing. The microorganism tested was Campylobacter jejuni and the results showed that the pathogen transferred to all utensils, at different transfer rate, despite the low level of the naturally contaminating pathogen. With unknown concentration bacteria in the naturally contaminated samples, a proportion of the utensils were still contaminated with C. jejuni and not surprisingly, when the sample were contaminated with higher concentrations of the pathogen, a higher proportion of the utensils had detectable C. jejuni cells present, though in many cases cross contamination seems to be a random event. Transfer of the naturally contaminating C. jejuni from the chicken liver and leg to the utensils were <3.0 to 9.2 MPN/g and <3.0 to 3.0 MPN/g, respectively. The results of this study highlighted the potential for cross contamination of food borne pathogens in the kitchen environment.

Unregulated Contaminant Monitoring Program Data

Data.gov (United States)

U.S. Environmental Protection Agency — EPA uses the Unregulated Contaminant Monitoring (UCM) program to collect data for contaminants suspected to be present in drinking water, but that do not have...

Phytoremediation of Soils Contaminated by Chlorinnated Hydrocarbons

Science.gov (United States)

Cho, C.; Sung, K.; Corapcioglu, M.

2001-12-01

In recent years, the possible use of deep rooted plants for phytoremediation of soil contaminants has been offered as a potential alternative for waste management, particularly for in situ remediation of large volumes of contaminated soils. Major objectives of this study are to evaluate the effectiveness of a warm season grass (Eastern Gamagrass) and a cool season prairie grass (Annual Ryegrass) in the phytoremediation of the soil contaminated with volatile organic compounds e.g., trichloroethylene (TCE), tetrachloroethylene (PCE), and 1,1,1-trichloroethane (TCA) and to determine the main mechanisms of target contaminant dissipation. The preliminary tests and laboratory scale tests were conducted to identify the main mechanisms for phytoremediation of the target contaminants, and to apply the technique in green house application under field conditions. The results of microcosm and bioreactor experiments showed that volatilization can be the dominant pathway of the target contaminant mass losses in soils. Toxicity tests, conducted in nutrient solution in the growth room, and in the greenhouse, showed that both Eastern gamagrass and Annual ryegrass could grow without harmful effects at up to 400 ppm each of all three contaminants together. Preliminary greenhouse experimentw were conducted with the 1.5 m long and 0.3 m diameter PVC columns. Soil gas concentrations monitored and microbial biomass in bulk and rhizosphere soil, root properties, and contaminant concentration in soil after 100 days were analyzed. The results showed that the soil gas concentration of contaminants has rapidly decreased especially in the upper soil and the contaminant concentraitons in soil were also significantly decreased to 0.024, 0.228, and 0.002 of C/Co for TCE, PCE and TCA, respectively. Significant plant effects were not found however showed contaminant loss through volatilization and plant contamination by air.

Defense Waste Management Plan for buried transuranic-contaminated waste, transuranic-contaminated soil, and difficult-to-certify transuranic waste

International Nuclear Information System (INIS)

1987-06-01

GAO recommended that DOE provide specific plans for permanent disposal of buried TRU-contaminated waste, TRU-contaminated soil, and difficult-to-certify TRU waste; cost estimates for permanent disposal of all TRU waste, including the options for the buried TRU-contaminated waste, TRU-contaminated soil, and difficult-to-certify TRU waste; and specific discussions of environmental and safety issues for the permanent disposal of TRU waste. Purpose of this document is to respond to the GAO recommendations by providing plans and cost estimates for the long-term isolation of the buried TRU-contaminated waste, TRU-contaminated soil, and difficult-to-certify TRU waste. This report also provides cost estimates for processing and certifying stored and newly generated TRU waste, decontaminating and decommissioning TRU waste processing facilities, and interim operations

Revelations of an overt water contamination.

Science.gov (United States)

Singh, Gurpreet; Kaushik, S K; Mukherji, S

2017-07-01

Contaminated water sources are major cause of water borne diseases of public health importance. Usually, contamination is suspected after an increase in patient load. Two health teams investigated the episode. First team conducted sanitary survey, and second team undertook water safety and morbidity survey. On-site testing was carried out from source till consumer end. Investigation was also undertaken to identify factors which masked the situation. Prevention and control measures included super chlorination, provision of alternate drinking water sources, awareness campaign, layout of new water pipeline bypassing place of contamination, repair of sewers, flushing and cleaning of water pipelines, and repeated water sampling and testing. Multiple sources of drinking water supply were detected. Water samples from consumer end showed 18 coliforms per 100 ml. Sewer cross connection with active leakage in water pipeline was found and this was confirmed by earth excavation. Water safety and morbidity survey found majority of households receiving contaminated water supply. This survey found no significant difference among households receiving contaminated water supply and those receiving clean water. Average proportion of household members with episode of loose motions, pain abdomen, vomiting, fever, and eye conditions was significantly more among households receiving contaminated water. The present study documents detailed methodology of investigation and control measures to be instituted on receipt of contaminated water samples. Effective surveillance mechanisms for drinking water supplies such as routine testing of water samples can identify water contamination at an early stage and prevent an impending outbreak.

Isotope hydrology: Investigating groundwater contamination

International Nuclear Information System (INIS)

Dubinchuk, V.; Froehlich, K.; Gonfiantini, R.

1989-01-01

Groundwater quality has worsened in many regions, with sometimes serious consequences. Decontaminating groundwater is an extremely slow process, and sometimes impossible, because of the generally long residence time of the water in most geological formations. Major causes of contamination are poor groundwater management (often dictated by immediate social needs) and the lack of regulations and control over the use and disposal of contaminants. These types of problems have prompted an increasing demand for investigations directed at gaining insight into the behaviour of contaminants in the hydrological cycle. Major objectives are to prevent pollution and degradation of groundwater resources, or, if contamination already has occurred, to identify its origin so that remedies can be proposed. Environmental isotopes have proved to be a powerful tool for groundwater pollution studies. The IAEA has had a co-ordinated research programme since 1987 on the application of nuclear techniques to determine the transport of contaminants in groundwater. An isotope hydrology project is being launched within the framework of the IAEA's regional co-operative programme in Latin America (known as ARCAL). Main objectives are the application of environmental isotopes to problems of groundwater assessment and contamination in Latin America. In 1989, another co-ordinated research programme is planned under which isotopic and other tracers will be used for the validation of mathematical models in groundwater transport studies

Contamination Analysis Tools

Science.gov (United States)

Brieda, Lubos

2015-01-01

This talk presents 3 different tools developed recently for contamination analysis:HTML QCM analyzer: runs in a web browser, and allows for data analysis of QCM log filesJava RGA extractor: can load in multiple SRS.ana files and extract pressure vs. time dataC++ Contamination Simulation code: 3D particle tracing code for modeling transport of dust particulates and molecules. Uses residence time to determine if molecules stick. Particulates can be sampled from IEST-STD-1246 and be accelerated by aerodynamic forces.

Redispersion of indoor surface contamination: a review

International Nuclear Information System (INIS)

Sansone, E.B.; Slein, M.W.

1978-01-01

The importance of surface contamination as a potential source of exposure to hazardous materials is discussed. Data from the literature concerning the resuspension of indoor surface contamination are presented. Reported procedures for quantitating surface contamination are compared. It is suggested that, despite its limitations, surface contamination monitoring may be useful in estimating potential risks from hazardous materials. (Auth.)

Surface contamination technology in decommissioning of nuclear fuel cycle

International Nuclear Information System (INIS)

Ishiguro, Hideharu

2012-01-01

Surface contamination measurement is the most basic technology in radiation control of the nuclear and radiation facilities. Loose surface contamination causes internal exposure through airborne contamination. Surface contamination measurement is recently more important in the waste management such as confirmation of decontamination factor, contamination survey of carried-out materials from radioactive control area, and application of clearance level. This report describes the base of surface contamination standards, meaning of contamination in decommissioning, relationship between clearance level and surface contamination, and current technology of surface contamination measurement. (author)

Geotechnical properties of crude oil contaminated sand

International Nuclear Information System (INIS)

Puri, V.K.; Das, B.M.; Cook, E.E.; Shin, E.C.

1994-01-01

Contamination of soil due to an oil spill influences its subsequent engineering behavior. An investigation was conducted to study the effect of crude oil contamination on compaction characteristics, shear strength, one-dimensional compression, and coefficient of permeability. Water permeability was also determined by using commercial grade motor oils as contaminants. The test results indicate that the compaction characteristics are influenced by oil contamination. The angle of internal friction of sand (based on total stress condition) decreases due to presence of oil within the pore spaces in sand. One dimensional compression characteristics of sand are significantly influenced by oil contamination resulting in a decrease in the value of constrained modulus with increase in the degree of oil contamination compared to the case of dry sand. Water permeability was observed to be a function of the initial viscosity and the degree of saturation due to the contaminating oil

Cadastral valuation of land contaminated with radionuclides

Science.gov (United States)

Ratnikov, A. N.; Sapozhnikov, P. M.; Sanzharova, N. I.; Sviridenko, D. G.; Zhigareva, T. L.; Popova, G. I.; Panov, A. V.; Kozlova, I. Yu.

2016-01-01

The methodology and procedure for cadastral valuation of land in the areas contaminated with radionuclides are presented. The efficiency of rehabilitation measures applied to decrease crop contamination to the levels satisfying sanitary-hygienic norms is discussed. The differentiation of cadastral value of radioactively contaminated agricultural lands for the particular farms and land plots is suggested. An example of cadastral valuation of agricultural land contaminated during the Chernobyl Nuclear Power Plant accident is given. It is shown that the use of sandy and loamy sandy soddy-podzolic soils with the 137Cs contamination of 37-185 and >185 kBq/m2 for crop growing is unfeasible. The growing of grain crops and potatoes on clay loamy soddy-podzolic soils with the 137Cs contamination of 555-740 kBq/m2 is unprofitable. The maximum cadastral value of radioactively contaminated lands is typical of leached chernozems.

Thorium-230 contamination

International Nuclear Information System (INIS)

Noey, K.C.; Liedle, S.D.; Hickey, C.R.; Doane, R.W.

1989-01-01

The authors are currently performing radiological surveys on approximately ninety properties in the St. Louis, Missouri area as part of the U.S. Department of Energy's Formerly Utilized Sites Remedial Action Program. The properties involved are the St. Louis Airport Site, Latty Avenue Properties, St. Louis Downtown Site, Coldwater Creek, and the associated roads and vicinity properties. The primary radioactive contaminant on these properties is thorium-230. Since field instrumentation is not available to detect the presence of alpha-emitting contamination in soil, soil samples are being collected and sent to an analytical laboratory for analysis. Thorium-230 analysis is costly and time-consuming, and as a result, soil sample analysis results are not available to help direct the field sampling program. This paper provides discussion of the manner in which the properties became radioactively contaminated, followed by a discussion of the difficulties associated with the detection of thorium-230. Finally, new methodologies for detecting alpha-emitting radionuclides in the field are described

Cesium contamination of mosses in county Vas, Hungary

International Nuclear Information System (INIS)

Golya, I.; Sebestyen, R.

1993-01-01

Two species of mosses were examined to assess radiocesium contamination of Vas county, and to analyse some aspects of mosses for use as indicator of radioactive contamination. Experimental results demonstrated that the distribution of contamination in a given region could be characterized by the cesium contamination of mosses. Sampling sites should be selected with special attention paid to spots with high contamination. Regression analysis proved that the contamination of mosses originated from Chernobyl fallout. (author) 4 refs.; 2 figs

Method of and apparatus for cleaning garments and soft goods contaminated with nuclear, chemical and/or biological contaminants

International Nuclear Information System (INIS)

Fowler, D.E.

1989-01-01

A method is described for decontaminating garments, soft good or mixtures thereof contaminated with radioactive particulates, toxin, chemical, and biological contaminants comprising the steps of: (a) depositing contaminated garments, soft goods or mixtures thereof in a cleaning drum; (b) charging the drum with a cleaning solvent in which the chemical contaminants are soluble; (c) agitating the drum during a wash cycle to separate radioactive, toxin, biological particulate matter of mixtures thereof from the garments; (d) draining the drum of the dry cleaning solvent which contains suspended particulate contaminants and dissolved chemical contaminants; (e) contacting the drained solvent with both a neutralizing agent and an oxidizing agent, the neutralizing agent being selected from the group consisting of sodium hydroxide, potassium hydroxide and mixtures thereof and having a concentration greater than one (1.0) normal; (f) rinsing the garments, soft goods or mixtures thereof by circulating clean solvent from a solvent tank through the drum thereby effecting additional removal and flushing of particulate and chemical contaminants; (g) filtering the circulated solvent to remove the particulate material suspended in the solvent prior to addition to the drum; and (h) preferentially adsorbing the chemical contaminants dissolved in the circulated solvent prior to addition to the drum

Delineation of contaminant plume for an inorganic contaminated site using electrical resistivity tomography: comparison with direct-push technique.

Science.gov (United States)

Liao, Qing; Deng, Yaping; Shi, Xiaoqing; Sun, Yuanyuan; Duan, Weidong; Wu, Jichun

2018-03-03

Precise delineation of contaminant plume distribution is essential for effective remediation of contaminated sites. Traditional in situ investigation methods like direct-push (DP) sampling are accurate, but are usually intrusive and costly. Electrical resistivity tomography (ERT) method, as a non-invasive geophysical technique to map spatiotemporal changes in resistivity of the subsurface, is becoming increasingly popular in environmental science. However, the resolution of ERT for delineation of contaminant plumes still remains controversial. In this study, ERT and DP technique were both conducted at a real inorganic contaminated site. The reliability of the ERT method was validated by the direct comparisons of their investigation results that the resistivity acquired by ERT method is in accordance with the total dissolved solid concentration in groundwater and the overall variation of the total iron content in soil obtained by DP technique. After testifying the applicability of ERT method for contaminant identification, the extension of contaminant plume at the study site was revealed by supplementary ERT surveys conducted subsequently in the surrounding area of the contaminant source zone.

Radioactive contamination incidents involving protective clothing

Energy Technology Data Exchange (ETDEWEB)

Reichelt, R.; Clay, M.; Eichorst, J.

1996-10-01

The study focuses on incidents at Department of Energy (DOE) facilities involving the migration of radioactive contaminants through protective clothing. The authors analyzed 68 occurrence reports for the following factors: (1) type of work; (2) working conditions; (3) type of anti-contamination (anti-C) material; (4) area of body or clothing contaminated; and (5) nature of spread of contamination. A majority of reports identified strenuous work activities such as maintenance, construction, or decontamination and decommissioning (D&D) projects. The reports also indicated adverse working conditions that included hot and humid or cramped work environments. The type of anti-C clothing most often identified was cotton or water-resistant, disposable clothing. Most of the reports also indicated contaminants migrating through perspiration-soaked areas, typically in the knees and forearms. On the basis of their survey, the authors recommend the use of improved engineering controls and resilient, breathable, waterproof protective clothing for work in hot, humid, or damp areas where the possibility of prolonged contact with contamination cannot be easily avoided or controlled.

Development of radioactive surface contamination monitor

International Nuclear Information System (INIS)

Hashimoto, Tadao; Hasegawa, Toru; Fukumoto, Keisuke; Ooki, Yasushi

2008-01-01

In the radiation facilities such as nuclear power plants, surface contamination of the people accessing or articles conveyed in and out of the radiation controlled areas is detected and monitored by installing contamination monitors at the boundary of controlled areas and uncontrolled areas against the expansion of the radioactive materials to out of the facilities. It is required for the surface contamination of articles to be tightened of control criteria as 'Guidelines for discrimination ways of nonradioactive waste (not classified as radioactive waste) generated from nuclear power plants' (hereinafter referred to as 'the Guideline') was established by the Nuclear and Industrial Safety Agency of the Ministry of Economy, Trade and Industry in August, 2005. It predicts that the control criteria of monitors other than article monitors are also tightened in the future. Fuji electric has been fabricating and delivering surface contamination detecting monitors. Now we are developing the new contamination monitor corresponding to the tightening of the control criteria. 'Large article transfer monitor', 'Clothing monitor' and 'Body surface contamination monitor' are introduced in this article. (author)

Radioactive contamination incidents involving protective clothing

International Nuclear Information System (INIS)

Reichelt, R.; Clay, M.; Eichorst, J.

1996-10-01

The study focuses on incidents at Department of Energy (DOE) facilities involving the migration of radioactive contaminants through protective clothing. The authors analyzed 68 occurrence reports for the following factors: (1) type of work; (2) working conditions; (3) type of anti-contamination (anti-C) material; (4) area of body or clothing contaminated; and (5) nature of spread of contamination. A majority of reports identified strenuous work activities such as maintenance, construction, or decontamination and decommissioning (D ampersand D) projects. The reports also indicated adverse working conditions that included hot and humid or cramped work environments. The type of anti-C clothing most often identified was cotton or water-resistant, disposable clothing. Most of the reports also indicated contaminants migrating through perspiration-soaked areas, typically in the knees and forearms. On the basis of their survey, the authors recommend the use of improved engineering controls and resilient, breathable, waterproof protective clothing for work in hot, humid, or damp areas where the possibility of prolonged contact with contamination cannot be easily avoided or controlled

Prevalence of Parasitic Contamination

Science.gov (United States)

Ismail, Yazan

2016-01-01

One of the main ways in transmitting parasites to humans is through consuming contaminated raw vegetables. The aim of this study was to evaluate the prevalence of parasitological contamination (helminthes eggs, Giardia and Entamoeba histolytica cysts) of salad vegetables sold at supermarkets and street vendors in Amman and Baqa’a – Jordan. A total of 133 samples of salad vegetables were collected and examined for the prevalence of parasites. It was found that 29% of the samples were contaminated with different parasites. Of the 30 lettuce, 33 tomato, 42 parsley and 28 cucumber samples examined the prevalence of Ascaris spp. eggs was 43%, 15%, 21% and 4%; Toxocara spp. eggs was 30%, 0%, 0% and 4%; Giardia spp. cysts was 23%, 6%, 0% and 0%; Taenia/Echinococcus eggs was 20%, 0%, 5% and 0%; Fasciola hepatica eggs was 13%, 3%, 2% and 0%; and E. histolytica cysts was 10%, 6%, 0% and 0%, respectively. There was no significant difference in the prevalence of parasite in salad vegetables either between supermarkets and street vendors, or between Amman and Baqa’a, Ascaris spp. was found to be the highest prevalent parasite in salad vegetables from supermarkets and street vendors and from Amman and Baqa’a. Our results pointed out that, the parasitic contamination of salad vegetables found in our study might be caused by irrigating crops with faecal contaminated water. We concluded that salad vegetables sold in Amman and Baqa’a may cause a health risk to consumers.

Costs of groundwater contamination

International Nuclear Information System (INIS)

O'Neil, W.B.; Raucher, R.S.

1990-01-01

Two factors determine the cost of groundwater contamination: (1) the ways in which water was being used or was expected to be used in the future and (2) the physical characteristics of the setting that constrain the responses available to regain lost uses or to prevent related damages to human health and the environment. Most contamination incidents can be managed at a low enough cost that uses will not be foreclosed. It is important to take into account the following when considering costs: (1) natural cleansing through recharge and dilution can take many years; (2) it is difficult and costly to identify the exact area and expected path of a contamination plume; and (3) treatment or replacement of contaminated water often may represent the cost-effective strategy for managing the event. The costs of contamination include adverse health effects, containment and remediation, treatment and replacement costs. In comparing the costs and benefits of prevention programs with those of remediation, replacement or treatment, it is essential to adjust the cost/benefit numbers by the probability of their actual occurrence. Better forecasts of water demand are needed to predict more accurately the scarcity of new supply and the associated cost of replacement. This research should include estimates of the price elasticity of water demand and the possible effect on demand of more rational cost-based pricing structures. Research and development of techniques for in situ remediation should be encouraged

Oral chlorhexidine and microbial contamination during endoscopy

DEFF Research Database (Denmark)

Donatsky, Anders Meller; Holzknecht, Barbara Juliane; Arpi, Magnus

2013-01-01

BACKGROUND: One of the biggest concerns associated with transgastric surgery is contamination and risk of intra-abdominal infection with microbes introduced from the access route. The purpose of this study was to evaluate the effect of oral decontamination with chlorhexidine on microbial contamin......BACKGROUND: One of the biggest concerns associated with transgastric surgery is contamination and risk of intra-abdominal infection with microbes introduced from the access route. The purpose of this study was to evaluate the effect of oral decontamination with chlorhexidine on microbial...... contamination of the endoscope. METHODS: In a prospective, randomized, single-blinded, clinical trial the effect of chlorhexidine mouth rinse was evaluated. As a surrogate for the risk of intra-abdominal contamination during transgastric surgery, microbial contamination of the endoscope during upper endoscopy...... microbial contamination of the endoscope, but micro-organisms with abscess forming capabilities were still present. PPI treatment significantly increased CFU and should be discontinued before transgastric surgery....

Prevention of airborne contamination and cross-contamination in germ-free mice by laminar flow

NARCIS (Netherlands)

Waaij, D. van der; Andres, A.H.

1971-01-01

The efficacy of horizontal and vertical laminar flow units (equipped with high-efficiency air filters) in the prevention of cross-contamination between cages and of contamination from outside has been demonstrated. With germ-free mice and using germ-free standard techniques for sterilization and for

Residual radioactive contamination from decommissioning: Technical basis for translating contamination levels to annual dose

International Nuclear Information System (INIS)

Kennedy, W.E. Jr.; Peloquin, R.A.

1990-01-01

This document describes the generic modeling of the total effective dose equivalent (TEDE) to an individual in a population from a unit concentration of residual radioactive contamination. Radioactive contamination inside buildings and soil contamination are considered. Unit concentration TEDE factors by radionuclide, exposure pathway, and exposure scenario are calculated. Reference radiation exposure scenarios are used to derive unit concentration TEDE factors for about 200 individual radionuclides and parent-daughter mixtures. For buildings, these unit concentration factors list the annual TEDE for volume and surface contamination situations. For soil, annual TEDE factors are presented for unit concentrations of radionuclides in soil during residential use of contaminated land and the TEDE per unit total inventory for potential use of drinking water from a ground-water source. Because of the generic treatment of potentially complex ground-water systems, the annual TEDE factors for drinking water for a given inventory may only indicate when additional site data or modeling sophistication are warranted. Descriptions are provided of the models, exposure pathways, exposure scenarios, parameter values, and assumptions used. An analysis of the potential annual TEDE resulting from reference mixtures of residual radionuclides is provided to demonstrate application of the TEDE factors. 62 refs., 5 figs., 66 tabs

Sustainable treatment of hydrocarbon-contaminated industrial land

OpenAIRE

Cunningham, Colin John

2012-01-01

Land contamination by petroleum hydrocarbons is a widespread and global environmental pollution issue from recovery and refining of crude oil and the ubiquitous use of hydrocarbons in industrial processes and applications. Sustainable treatment of hydrocarbon-contaminated industrial land was considered with reference to seven published works on contaminated railway land including the track ballast, crude oil wastes and contaminated refinery soils. A methodology was developed...

Contaminated environments in the subsurface and bioremediation: organic contaminants.

Science.gov (United States)

Holliger, C; Gaspard, S; Glod, G; Heijman, C; Schumacher, W; Schwarzenbach, R P; Vazquez, F

1997-07-01

Due to leakages, spills, improper disposal and accidents during transport, organic compounds have become subsurface contaminants that threaten important drinking water resources. One strategy to remediate such polluted subsurface environments is to make use of the degradative capacity of bacteria. It is often sufficient to supply the subsurface with nutrients such as nitrogen and phosphorus, and aerobic treatments are still dominating. However, anaerobic processes have advantages such as low biomass production and good electron acceptor availability, and they are sometimes the only possible solution. This review will focus on three important groups of environmental organic contaminants: hydrocarbons, chlorinated and nitroaromatic compounds. Whereas hydrocarbons are oxidized and completely mineralized under anaerobic conditions in the presence of electron acceptors such as nitrate, iron, sulfate and carbon dioxide, chlorinated and nitroaromatic compounds are reductively transformed. For the aerobic often persistent polychlorinated compounds, reductive dechlorination leads to harmless products or to compounds that are aerobically degradable. The nitroaromatic compounds are first reductively transformed to the corresponding amines and can subsequently be bound to the humic fraction in an aerobic process. Such new findings and developments give hope that in the near future contaminated aquifers can efficiently be remediated, a prerequisite for a sustainable use of the precious-subsurface drinking water resources.

Surface soil contamination standards

International Nuclear Information System (INIS)

Boothe, G.F.

1979-01-01

The purpose of this document is to define surface soil contamination limits for radioactive materials below which posting, restrictions and environmental controls are not necessary in order to protect personnel and the environment. The standards can also be used to determine if solid waste or other material is contaminated relative to disposal requirements. The derivation of the standards is given

Toxicity of lead-contaminated sediment to mallards

Science.gov (United States)

Heinz, G.H.; Hoffman, D.J.; Sileo, L.; Audet, D.J.; LeCaptain, L.J.

1999-01-01

Because consumption of lead-contaminated sediment has been suspected as the cause of waterfowl mortality in the Coeur d?Alene River basin in Idaho, we studied the bioavailability and toxicity of this sediment to mallards (Anas platyrhynchos). In experiment 1, one of 10 adult male mallards died when fed a pelleted commercial duck diet that contained 24% lead-contaminated sediment (with 3,400 μg/g lead in the sediment). Protoporphyrin levels in the blood increased as the percentage of lead-contaminated sediment in the diet increased. Birds fed 24% lead-contaminated sediment exhibited atrophy of the breast muscles, green staining of the feathers around the vent, viscous bile, green staining of the gizzard lining, and renal tubular intranuclear inclusion bodies. Mallards fed 24% lead-contaminated sediment had means of 6.1 μg/g of lead in the blood and 28 μg/g in the liver (wet-weight basis) and 1,660 μg/g in the feces (dry-weight basis). In experiment 2, we raised the dietary concentration of the lead-contaminated sediment to 48%, but only about 20% sediment was actually ingested due to food washing by the birds. Protoporphyrin levels were elevated in the lead-exposed birds, and all of the mallards fed 48% lead-contaminated sediment had renal tubular intranuclear inclusion bodies. The concentrations of lead in the liver were 9.1 μg/g for mallards fed 24% lead-contaminated sediment and 16 μg/g for mallards fed 48% lead-contaminated sediment. In experiment 3, four of five mallards died when fed a ground corn diet containing 24% lead-contaminated sediment (with 4,000 μg/g lead in this sample of sediment), but none died when the 24% lead-contaminated sediment was mixed into a nutritionally balanced commercial duck diet; estimated actual ingestion rates for sediment were 14% and 17% for the corn and commercial diets. Lead exposure caused elevations in protoporphyrin, and four of the five mallards fed 24% lead-contaminated sediment in a commercial diet and all five

Contaminant exposure in terrestrial vertebrates

International Nuclear Information System (INIS)

Smith, Philip N.; Cobb, George P.; Godard-Codding, Celine; Hoff, Dale; McMurry, Scott T.; Rainwater, Thomas R.; Reynolds, Kevin D.

2007-01-01

Here we review mechanisms and factors influencing contaminant exposure among terrestrial vertebrate wildlife. There exists a complex mixture of biotic and abiotic factors that dictate potential for contaminant exposure among terrestrial and semi-terrestrial vertebrates. Chemical fate and transport in the environment determine contaminant bioaccessibility. Species-specific natural history characteristics and behavioral traits then play significant roles in the likelihood that exposure pathways, from source to receptor, are complete. Detailed knowledge of natural history traits of receptors considered in conjunction with the knowledge of contaminant behavior and distribution on a site are critical when assessing and quantifying exposure. We review limitations in our understanding of elements of exposure and the unique aspects of exposure associated with terrestrial and semi-terrestrial taxa. We provide insight on taxa-specific traits that contribute, or limit exposure to, transport phenomenon that influence exposure throughout terrestrial systems, novel contaminants, bioavailability, exposure data analysis, and uncertainty associated with exposure in wildlife risk assessments. Lastly, we identify areas related to exposure among terrestrial and semi-terrestrial organisms that warrant additional research. - Both biotic and abiotic factors determine chemical exposure for terrestrial vertebrates

Remediation of lead-contaminated soils

International Nuclear Information System (INIS)

Peters, R.W.; Shem, L.

1992-01-01

Excavation and transport of soil contaminated with heavy metals has generally been the standard remediation technique for treatment of heavy-metal-contaminated soils. This approach is not a permanent solution; moreover, off-site shipment and disposal of contaminated soil involves high expense, liability, and appropriate regulatory approval. Recently, a number of other techniques have been investigated for treating such contaminated sites, including flotation, solidification/stabilization, vitrification, and chemical extraction. This paper reports the results of a laboratory investigation determining the efficiency of using chelating agents to extract lead from contaminated soils. Lead concentrations in the soils ranged from 500 to 10,000 mg/kg. Ethylenediaminetetraacetic acid (EDTA) and nitrilotriacetic acid (NTA) were examined for their potential extractive capabilities. Concentrations of the chelating agents ranged from 0.01 to 0.10 M. The pH of the suspensions in which the extractions were performed ranged from 4 to 12. Results showed that the removal of lead using NTA and water was ph-dependent, whereas the removal of lead using EDTA was ph-insensitive. Maximum removals of lead were 68.7%,19.1%, and 7.3% using EDTA, NTA, and water, respectively (as compared with initial lead concentrations)

Radioactive contamination in imported foods

International Nuclear Information System (INIS)

Kan, Kimiko; Maki, Toshio; Nagayama, Toshihiro; Hashimoto, Hideki; Kawai, Yuka; Kobayashi, Maki; Shioda, Hiroko; Nishima, Taichiro

1990-01-01

On April 26, 1986, explosion occurred in Chernobyl nuclear power station in USSR, and radioactivity contamination was brought about in almost all countries in the world. In European countries, crops were contaminated directly with radioactive fallout to high concentration. Also in Japan, after one week the radioactivity higher than usual was detected in environment, and also in vegetables, milk, tea leaves and others. Thereafter, in order to cope with the import of contaminated foods, inspection and watch system was strengthened by deciding the interim limit of radioactive concentration. However the cases of exceeding the interim limit were often reported. In order to remove the harmful foods due to radioactive contamination and to meet the fear of consumers, the authors measured the radioactive concentration in foods distributed in Tokyo and investigated the actual state of contamination. The samples were 920 imported foods. The experimental method, the preparation of samples, the method of analysis and the results are reported. The samples in which the radioactive concentration exceeding 50 Bq/kg was detected were 25 cases. The food having the high frequency of detection was flavors. (K.I.)

Contamination versus preservation of cosmetics

DEFF Research Database (Denmark)

Lundov, Michael Dyrgaard; Moesby, Lise; Zachariae, Claus

2009-01-01

Cosmetics with high water content are at a risk of being contaminated by micro-organisms that can alter the composition of the product or pose a health risk to the consumer. Pathogenic micro-organisms such as Staphylococcus aureus and Pseudomonas aeruginosa are frequently found in contaminated...... cosmetics. In order to avoid contamination of cosmetics, the manufacturers add preservatives to their products. In the EU and the USA, cosmetics are under legislation and all preservatives must be safety evaluated by committees. There are several different preservatives available but the cosmetic market...

Environmental contamination with Toxocara eggs

NARCIS (Netherlands)

Nijsse, Rolf; Mughini-Gras, Lapo; Wagenaar, J.A.; Franssen, Frits; Ploeger, Harm W.

2015-01-01

Background: Environmental contamination with Toxocara eggs is considered the main source of human toxocariasis. The contribution of different groups of hosts to this contamination is largely unknown. Current deworming advices focus mainly on dogs. However, controversy exists about blind deworming

Noninvasive characterization of the Trecate (Italy) crude-oil contaminated site: links between contamination and geophysical signals.

Science.gov (United States)

Cassiani, Giorgio; Binley, Andrew; Kemna, Andreas; Wehrer, Markus; Orozco, Adrian Flores; Deiana, Rita; Boaga, Jacopo; Rossi, Matteo; Dietrich, Peter; Werban, Ulrike; Zschornack, Ludwig; Godio, Alberto; JafarGandomi, Arash; Deidda, Gian Piero

2014-01-01

The characterization of contaminated sites can benefit from the supplementation of direct investigations with a set of less invasive and more extensive measurements. A combination of geophysical methods and direct push techniques for contaminated land characterization has been proposed within the EU FP7 project ModelPROBE and the affiliated project SoilCAM. In this paper, we present results of the investigations conducted at the Trecate field site (NW Italy), which was affected in 1994 by crude oil contamination. The less invasive investigations include ground-penetrating radar (GPR), electrical resistivity tomography (ERT), and electromagnetic induction (EMI) surveys, together with direct push sampling and soil electrical conductivity (EC) logs. Many of the geophysical measurements were conducted in time-lapse mode in order to separate static and dynamic signals, the latter being linked to strong seasonal changes in water table elevations. The main challenge was to extract significant geophysical signals linked to contamination from the mix of geological and hydrological signals present at the site. The most significant aspects of this characterization are: (a) the geometrical link between the distribution of contamination and the site's heterogeneity, with particular regard to the presence of less permeable layers, as evidenced by the extensive surface geophysical measurements; and (b) the link between contamination and specific geophysical signals, particularly evident from cross-hole measurements. The extensive work conducted at the Trecate site shows how a combination of direct (e.g., chemical) and indirect (e.g., geophysical) investigations can lead to a comprehensive and solid understanding of a contaminated site's mechanisms.

Radioactive contamination in imported foods (II)

International Nuclear Information System (INIS)

Kan, Kimiko; Maki, Toshio; Hashimoto, Hideki; Kawai, Yuka; Nagayama, Toshihiro; Kobayashi, Maki; Shioda, Hiroko; Nishima, Taichiro

1991-01-01

Five years have elapsed since the Chernobyl accident, but the effect of radioactivity contamination to foods has continued. Also in Japan, the imported foods which were ordered by the Ministry of Health and Welfare to be sent back due to radioactivity contamination do not cease. In fiscal year 1990, three cases occurred: tea from Albania, mushrooms from Yugoslavia and spices from france. If those are not checked at quarantines, it is feared that such foods are distributed in Japan. Among the foods which were ordered to be sent back in the past, there were those from Brazil and Hong Kong where the effect of the Chernobyl accident is little, and the foods contaminated with radioactivity spread worldwide through import and export. Therefore, attention must be paid to the foods from the countries where radioactivity contamination is little. Also it is feared that Japanese foods may be contaminated by being cultivated with imported feed, soil and fertilizer, for which there is no regulation. In this report, the radioactivity contamination of imported foods in fiscal year 1990 is described, and the experimental method and the results are reported. (K.I.)

Oil contamination in Ogoniland, Niger Delta.

Science.gov (United States)

Lindén, Olof; Pålsson, Jonas

2013-10-01

The study shows extensive oil contamination of rivers, creeks, and ground waters in Ogoniland, Nigeria. The levels found in the more contaminated sites are high enough to cause severe impacts on the ecosystem and human health: extractable petroleum hydrocarbons (EPHs) (>10-C40) in surface waters up to 7420 μg L(-1), drinking water wells show up to 42 200 μg L(-1), and benzene up to 9000 μg L(-1), more than 900 times the WHO guidelines. EPH concentrations in sediments were up to 17 900 mg kg(-1). Polycyclic aromatic hydrocarbons concentrations reached 8.0 mg kg(-1), in the most contaminated sites. The contamination has killed large areas of mangroves. Although the natural conditions for degradation of petroleum hydrocarbons are favorable with high temperatures and relatively high rainfall, the recovery of contaminated areas is prevented due to the chronic character of the contamination. Oil spills of varying magnitude originates from facilities and pipelines; leaks from aging, dilapidated, and abandoned infrastructure; and from spills during transport and artisanal refining of stolen oil under very primitive conditions.

A proximity effect in adults' contamination intuitions

Directory of Open Access Journals (Sweden)

Laura R. Kim

2011-04-01

Full Text Available Magical beliefs about contagion via contact (Rozin, Nemeroff, Wane, and Sherrod, 1989 may emerge when people overgeneralize real-world mechanisms of contamination beyond their appropriate boundaries (Lindeman and Aarnio, 2007. Do people similarly overextend knowledge of airborne contamination mechanisms? Previous work has shown that very young children believe merely being close to a contamination source can contaminate an item (Springer and Belk 1994; we asked whether this same hyper-avoidant intuition is also reflected in adults' judgments. In two studies, we measured adults' ratings of the desirability of an object that had made contact with a source of contamination, an object nearby that had made no contact with the contaminant, and an object far away that had also made no contact. Adults showed a clear proximity effect, wherein objects near the contamination source were perceived to be less desirable than those far away, even though a separate group of adults unanimously acknowledged that contaminants could not possibly have made contact with either the nearby or far-away object (Study 1. The proximity effect also remained robust when a third group of adults was explicitly told that no contaminating particles had made contact with the objects at any time (Study 2. We discuss implications of our findings for extending the scope of magical contagion effects beyond the contact principle, for understanding the persistence of intuitive theories despite broad acceptance of science-based theories, and for constraining interpretations of the developmental work on proximity beliefs.

Biological monitoring of environmental contaminants (plants). Executive summary

Energy Technology Data Exchange (ETDEWEB)

Burton, M.A.S.

1986-01-01

Knowledge of contaminant concentrations does not necessarily indicate their significance to plant populations and communities within ecosystems. Accumulation within plants facilitates analysis of contaminants which may be present at very low levels in the environment and may show the spatial distribution and changes in the level of contamination with time. Effects on species distribution within plant communities and visible injury to foliage may also be related to contamination. Species can be selected appropriate to the area and the contaminant to be monitored. Species used to investigate the input of contaminants from atmospheric deposition, for example, may differ from those used to assess transfer through food webs. Mosses and lichens have been particularly widely used in many countries to show distribution of metals and radionuclides on local and regional scales and of pesticide contamination. Visible injury to foliage of higher plant species may reflect atmospheric concentrations of gaseous pollutants and monitoring networks of transplanted sensitive species can provide information on contaminant levels on a regional scale. Changes in species composition, especially of lichens, have also been related to the degree of contamination.

Inexact Socio-Dynamic Modeling of Groundwater Contamination Management

Science.gov (United States)

Vesselinov, V. V.; Zhang, X.

2015-12-01

Groundwater contamination may alter the behaviors of the public such as adaptation to such a contamination event. On the other hand, social behaviors may affect groundwater contamination and associated risk levels such as through changing ingestion amount of groundwater due to the contamination. Decisions should consider not only the contamination itself, but also social attitudes on such contamination events. Such decisions are inherently associated with uncertainty, such as subjective judgement from decision makers and their implicit knowledge on selection of whether to supply water or reduce the amount of supplied water under the scenario of the contamination. A socio-dynamic model based on the theories of information-gap and fuzzy sets is being developed to address the social behaviors facing the groundwater contamination and applied to a synthetic problem designed based on typical groundwater remediation sites where the effects of social behaviors on decisions are investigated and analyzed. Different uncertainties including deep uncertainty and vague/ambiguous uncertainty are effectively and integrally addressed. The results can provide scientifically-defensible decision supports for groundwater management in face of the contamination.

Probability mapping of contaminants

International Nuclear Information System (INIS)

Rautman, C.A.; Kaplan, P.G.; McGraw, M.A.; Istok, J.D.; Sigda, J.M.

1994-01-01

Exhaustive characterization of a contaminated site is a physical and practical impossibility. Descriptions of the nature, extent, and level of contamination, as well as decisions regarding proposed remediation activities, must be made in a state of uncertainty based upon limited physical sampling. The probability mapping approach illustrated in this paper appears to offer site operators a reasonable, quantitative methodology for many environmental remediation decisions and allows evaluation of the risk associated with those decisions. For example, output from this approach can be used in quantitative, cost-based decision models for evaluating possible site characterization and/or remediation plans, resulting in selection of the risk-adjusted, least-cost alternative. The methodology is completely general, and the techniques are applicable to a wide variety of environmental restoration projects. The probability-mapping approach is illustrated by application to a contaminated site at the former DOE Feed Materials Production Center near Fernald, Ohio. Soil geochemical data, collected as part of the Uranium-in-Soils Integrated Demonstration Project, have been used to construct a number of geostatistical simulations of potential contamination for parcels approximately the size of a selective remediation unit (the 3-m width of a bulldozer blade). Each such simulation accurately reflects the actual measured sample values, and reproduces the univariate statistics and spatial character of the extant data. Post-processing of a large number of these equally likely statistically similar images produces maps directly showing the probability of exceeding specified levels of contamination (potential clean-up or personnel-hazard thresholds)

Probability mapping of contaminants

Energy Technology Data Exchange (ETDEWEB)

Rautman, C.A.; Kaplan, P.G. [Sandia National Labs., Albuquerque, NM (United States); McGraw, M.A. [Univ. of California, Berkeley, CA (United States); Istok, J.D. [Oregon State Univ., Corvallis, OR (United States); Sigda, J.M. [New Mexico Inst. of Mining and Technology, Socorro, NM (United States)

1994-04-01

Exhaustive characterization of a contaminated site is a physical and practical impossibility. Descriptions of the nature, extent, and level of contamination, as well as decisions regarding proposed remediation activities, must be made in a state of uncertainty based upon limited physical sampling. The probability mapping approach illustrated in this paper appears to offer site operators a reasonable, quantitative methodology for many environmental remediation decisions and allows evaluation of the risk associated with those decisions. For example, output from this approach can be used in quantitative, cost-based decision models for evaluating possible site characterization and/or remediation plans, resulting in selection of the risk-adjusted, least-cost alternative. The methodology is completely general, and the techniques are applicable to a wide variety of environmental restoration projects. The probability-mapping approach is illustrated by application to a contaminated site at the former DOE Feed Materials Production Center near Fernald, Ohio. Soil geochemical data, collected as part of the Uranium-in-Soils Integrated Demonstration Project, have been used to construct a number of geostatistical simulations of potential contamination for parcels approximately the size of a selective remediation unit (the 3-m width of a bulldozer blade). Each such simulation accurately reflects the actual measured sample values, and reproduces the univariate statistics and spatial character of the extant data. Post-processing of a large number of these equally likely statistically similar images produces maps directly showing the probability of exceeding specified levels of contamination (potential clean-up or personnel-hazard thresholds).

Nanomaterial-enabled Rapid Detection of Water Contaminants.

Science.gov (United States)

Mao, Shun; Chang, Jingbo; Zhou, Guihua; Chen, Junhong

2015-10-28

Water contaminants, e.g., inorganic chemicals and microorganisms, are critical metrics for water quality monitoring and have significant impacts on human health and plants/organisms living in water. The scope and focus of this review is nanomaterial-based optical, electronic, and electrochemical sensors for rapid detection of water contaminants, e.g., heavy metals, anions, and bacteria. These contaminants are commonly found in different water systems. The importance of water quality monitoring and control demands significant advancement in the detection of contaminants in water because current sensing technologies for water contaminants have limitations. The advantages of nanomaterial-based sensing technologies are highlighted and recent progress on nanomaterial-based sensors for rapid water contaminant detection is discussed. An outlook for future research into this rapidly growing field is also provided. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Subsurface Contaminants Focus Area annual report 1997

International Nuclear Information System (INIS)

1997-01-01

In support of its vision for technological excellence, the Subsurface Contaminants Focus Area (SCFA) has identified three strategic goals. The three goals of the SCFA are: Contain and/or stabilize contamination sources that pose an imminent threat to surface and ground waters; Delineate DNAPL contamination in the subsurface and remediate DNAPL-contaminated soils and ground water; and Remove a full range of metal and radionuclide contamination in soils and ground water. To meet the challenges of remediating subsurface contaminants in soils and ground water, SCFA funded more than 40 technologies in fiscal year 1997. These technologies are grouped according to the following product lines: Dense Nonaqueous-Phase Liquids; Metals and Radionuclides; Source Term Containment; and Source Term Remediation. This report briefly describes the SCFA 1997 technologies and showcases a few key technologies in each product line

CONTAMINANTS AND REMEDIAL OPTIONS AT PESTICIDE SITES

Science.gov (United States)

Many types of soils, sediments, and sludges are contaminated with a wide variety of pesticides. ite-specific characteristics such as volume to be treated, extent of contamination, and applicable cleanup goals differ greatly, and contaminant toxicity, migration pathways, persisten...

Assessing the bioavailability and risk from metal-contaminated ...

Science.gov (United States)

Exposure to contaminated soil and dust is an important pathway in human health risk assessment. Physical and chemical characteristics, as well as biological factors, determine the bioaccessibility/bioavailability of soil and dust contaminants. Within a single sample, contamination may arise from multiple sources of toxic elements that may exist as different forms (species) which impact bioavailability. In turn, the bioaccessibility/bioavailability of soil and dust contaminants has a direct impact on human health risk assessment and risk management practices. Novel research efforts focusing on development and application of in vitro and in vivo methods to measure the bioaccessibility/bioavailability of metal contaminated soils have advanced in the past few years. The objective of this workshop was to focus on recent developments in assessing the bioaccessibility/bioavailability of arsenic contaminated soils, metal contamination in urban residences in Canada and potential children’s exposures to toxic elements in house dust, a community-based study known as the West Oakland Residential Lead Assessment , studies of the bioavailability of soil cadmium, chromium, nickel and mercury and human exposures to contaminated Brownfield soils. These presentations covered issues related to human health and bioavailability along with the most recent studies on community participation in assessing metal contamination, studies of exposures to residential contamination, and

Inorganic and organic contaminants in Alaskan shorebird eggs.

Science.gov (United States)

Saalfeld, David T; Matz, Angela C; McCaffery, Brian J; Johnson, Oscar W; Bruner, Phil; Lanctot, Richard B

2016-05-01

Many shorebird populations throughout North America are thought to be declining, with potential causes attributed to habitat loss and fragmentation, reduced prey availability, increased predation, human disturbance, and increased exposure to environmental pollutants. Shorebirds may be particularly vulnerable to contaminant exposure throughout their life cycle, as they forage primarily on invertebrates in wetlands, where many contaminants accumulate disproportionately in the sediments. Therefore, it is important to document and monitor shorebird populations thought to be at risk and assess the role that environmental contaminants may have on population declines. To investigate potential threats and provide baseline data on shorebird contaminant levels in Alaskan shorebirds, contaminant concentrations were evaluated in shorebird eggs from 16 species residing in seven geographic distinct regions of Alaska. Similar to previous studies, low levels of most inorganic and organic contaminants were found, although concentrations of several inorganic and organic contaminants were higher than those of previous studies. For example, elevated strontium levels were observed in several species, especially black oystercatcher (Haematopus bachmani) sampled in Prince William Sound, Alaska. Additionally, contaminant concentrations varied among species, with significantly higher concentrations of inorganic contaminants found in eggs of pectoral sandpiper (Calidris melanotos), semipalmated sandpiper (Calidris pusilla), black oystercatcher, and bar-tailed godwit (Limosa lapponica). Similarly, significantly higher concentrations of some organic contaminants were found in the eggs of American golden plover (Pluvialis dominica), black-bellied plover (Pluvialis squatarola), pacific golden plover (Pluvialis fulva), bar-tailed godwit, and semipalmated sandpiper. Despite these elevated levels, current concentrations of contaminants in shorebird eggs suggest that breeding environments are

Microbial Contamination of Pastry Cream: Evidence from Iran

Directory of Open Access Journals (Sweden)

Mohamadreza Pajohi-alamoti

2016-07-01

Full Text Available Background & Aims of the Study: Given the importance of microbial contamination in creating food-borne diseases, this study was conducted to assess level of microbial contamination of pastry creams in Hamedan, Iran. Materials and Methods: Totally, 80 samples were randomly collected from the confectioneries and analyzed for microbial contamination according to Iranian national standard microbial tests. Results: Data indicated that 49 (61.2% samples were contaminated, mostly comprised of Coliforms (92.5%. Moreover, the infection was seen to be higher in jelly roll compared to puff pastry. Yeast contamination was about 82.5 percent, which could accelerate the decay of such products. However, yeast contamination of puff pastries was higher than jelly roll. The microbial contamination with Staphylococcus aureus, total viable count and molds were 57.5%, 35% and 37.5%; respectively. Conclusion: Nevertheless, Salmonella, Escherichia coli and Listeria monocytogenes were not found in any of the samples. Abundance of microbial contamination in the puff pastry samples might put consumer’s health at risk.

Field based plastic contamination sensing

Science.gov (United States)

The United States has a long-held reputation of being a dependable source of high quality, contaminant-free cotton. Recently, increased incidence of plastic contamination from sources such as shopping bags, vegetable mulch, surface irrigation tubing, and module covers has threatened the reputation o...

Air contamination for predicting wound contamination in clean surgery: A large multicenter study.

Science.gov (United States)

Birgand, Gabriel; Toupet, Gaëlle; Rukly, Stephane; Antoniotti, Gilles; Deschamps, Marie-Noelle; Lepelletier, Didier; Pornet, Carole; Stern, Jean Baptiste; Vandamme, Yves-Marie; van der Mee-Marquet, Nathalie; Timsit, Jean-François; Lucet, Jean-Christophe

2015-05-01

The best method to quantify air contamination in the operating room (OR) is debated, and studies in the field are controversial. We assessed the correlation between 2 types of air sampling and wound contaminations before closing and the factors affecting air contamination. This multicenter observational study included 13 ORs of cardiac and orthopedic surgery in 10 health care facilities. For each surgical procedure, 3 microbiologic air counts, 3 particles counts of 0.3, 0.5, and 5 μm particles, and 1 bacteriologic sample of the wound before skin closure were performed. We collected data on surgical procedures and environmental characteristics. Of 180 particle counts during 60 procedures, the median log10 of 0.3, 0.5, and 5 μm particles was 7 (interquartile range [IQR], 6.2-7.9), 6.1 (IQR, 5.4-7), and 4.6 (IQR, 0-5.2), respectively. Of 180 air samples, 50 (28%) were sterile, 90 (50%) had 1-10 colony forming units (CFU)/m(3) and 40 (22%) >10 CFU/m(3). In orthopedic and cardiac surgery, wound cultures at closure were sterile for 24 and 9 patients, 10 and 11 had 1-10 CFU/100 cm(2), and 0 and 6 had >10 CFU/100 cm(2), respectively (P air microbial counts (P contamination (P = .22). This study suggests that particle counting is a good surrogate of airborne microbiologic contamination in the OR. Copyright © 2015 Association for Professionals in Infection Control and Epidemiology, Inc. Published by Elsevier Inc. All rights reserved.

NERIS workshop. Lasting contaminations and land development. After Fukushima: the possibility of a lasting radioactive contamination

International Nuclear Information System (INIS)

2011-11-01

The document contains the contributions proposed during a workshop and the content of discussions after these contributions. For the first day, case studies are thus reported and commented: land contamination in Japan after the Fukushima accident, the CENTRACO plant accident, medium and long term stakes within the context of a lasting contamination by pesticides (the case of chlordecone pollution in the French West Indies), the complex and multiple actor challenges in the case of long duration radiological contamination for land agriculture, a lasting contamination in urban environment (the case of Metaleurop). The second session addressed the conditions and means for preparedness of local actors to a lasting radioactive contamination: the Norwegian approach, how to take the post-accidental perspective into account in the local safeguard plans, the PRIME project (research project on radio-ecological sensitivity indices and multi-criteria methods applied to the environment of an industrial territory), the pilot radiation protection project of the Montbeliard district, the OPAL project (to provide the local information commissions with post-accidental zoning information on the different French nuclear sites)

Photocatalytic remediation of contaminated solids

Energy Technology Data Exchange (ETDEWEB)

Chiarenzelli, J R; Scrudato, R J [State Univ. of New York, Oswego, NY (United States). Research Center

1996-12-31

Results of various experiments to utilize photocatalysis to photodegrade polychlorinated biphenyls (PCBs) and pesticide-contaminated sediments and soils in slurry suspensions, were discussed. The mechanism of the reaction, i. e. simultaneously bringing together the catalyst, contaminant and light through mixing or overturn of the material, was explained. Potential advantages of the method (on-site treatment, simultaneous degradation of multiple contaminants, low energy requirements, no emission of toxic effluents, reusable inert catalyst, no landfilling or future liability, etc.,) were reviewed. A pilot-scale test is planned for the near future to provide performance data needed for eventual commercialization. 8 refs.

Toothbrush Contamination: A Review of the Literature

Directory of Open Access Journals (Sweden)

Michelle R. Frazelle

2012-01-01

Full Text Available Toothbrushes are commonly used in hospital settings and may harbor potentially harmful microorganisms. A peer-reviewed literature review was conducted to evaluate the cumulative state of knowledge related to toothbrush contamination and its possible role in disease transmission. A systematic review was conducted on adult human subjects through three distinct searches. The review resulted in seven experimental and three descriptive studies which identified multiple concepts related to toothbrush contamination to include contamination, methods for decontamination, storage, design, and environmental factors. The selected studies found that toothbrushes of healthy and oral diseased adults become contaminated with pathogenic bacteria from the dental plaque, design, environment, or a combination of factors. There are no studies that specifically examine toothbrush contamination and the role of environmental factors, toothbrush contamination, and vulnerable populations in the hospital setting (e.g., critically ill adults and toothbrush use in nursing clinical practice.

Dosimetry and therapy of skin contaminations

International Nuclear Information System (INIS)

Piechowski, J.; Menoux, B.; Chaptinel, Y.; Durand, F.

1988-10-01

This study has been developed to provide guidance to physicians on the handling of skin contaminations in some accidental circumstances. The first stage of diagnosis and consequently of the possible therapy in order to avoid or mitigate radiodermatitis is to appreciate the importance of the contaminations and to foresee their local consequences. Two theoretical cases have been considered: a) strictly superficial contamination; b) deep contamination with homogeneous penetration of the contaminant into the epidermis. The superficial and deep theoretical distributions correspond respectively to the lower and upper absorbed doses in the basal layer. Tables of dose equivalent rates and committed dose equivalents to the skin are supplied for a large number of radionuclides likely to be met in the nuclear industry as well as in various fields of research, medicine and pharmacology using radioactive techniques. Besides these theoretical dose factors, the practitioner will find monitoring procedures, dose calculations and practical data concerning decontamination [fr

Sensitivity to contamination of optical coatings

International Nuclear Information System (INIS)

Macleod, A.

1999-01-01

A simple theory is presented of the sensitivity to contamination of optical coatings, which permits prediction of performance degradation in the presence of small deposit s of absorbing material. Although a major objective is the ability to compare the sensitivities of different coating types, absolute values can be made possible by adopting a standard contamination layer consisting of a 1 Angstrom thickness of carbon. Results are quoted for a number of common thin-film coatings and filters and are sometimes surprising. The common high-reflectance coating is the quarterwave stack and, at its reference wavelength, it has very low sensitivity to contamination. Although minor constructional errors have little effect on the reflectance, they can seriously affect the contamination sensitivity. Further, the level of contamination determines the maximum reflectance it is possible to achieve, regardless of the number of layers in the coating. The admittance diagram helps in understanding the reasons for the very large variations in sensitivity between coatings with quite similar reflectance

Real significance of skin contamination is

International Nuclear Information System (INIS)

Sudmann, R.H.

1983-01-01

For five decades, health physicists have discussed the thickness, area, significance of radioactive contamination and the exposures to various portions of the skin. Concern about instances of skin contamination extend beyond the resultant organ dose simply because it is a recognizable and quantifiable event. As such, there is a tendency for management and regulatory agencies to use it as a trend indicator. The final result is a score card similar to the list of OSHA reportable accidents. In fact, the skin contamination incidence rate has a somewhat different meaning to the health physicist, to the manager, and to the regulator. The question must then be asked, What is the true significance of skin contamination, Is it the resultant skin dose, Is it an indicator of loss of control, Is it both or neither. In order to answer these questions, Rockwell Hanford Operations began analysis of the previous five years records of skin contamination cases. Since by policy each incidence of skin contamination is documented, a large percentage of the 425 records analyzed were of low level activity (less than 100 dpm/cm 2 ) on the extremeties, primarily hands and fingers. Most of these cases were readily decontaminated with soap and water. Individual elements studied included: detection/monitoring methods and limits; impact of type of operation on the incidence rate; causes of and methods for reduction of the incidence rate; reporting and documentation; and dose assessment. Results of the study indicate that skin contamination rarely presents a beta dose problem because it is normally highly localized on the extremeties. Only in unusual cases does it represent a potential for internal deposition. Thus, the real importance of skin contamination incidence is as an indicator of deteriorating conditions and should be reviewed by health physicists, managers and regulators as such

Directional phytoscreening: contaminant gradients in trees for plume delineation.

Science.gov (United States)

Limmer, Matt A; Shetty, Mikhil K; Markus, Samantha; Kroeker, Ryan; Parker, Beth L; Martinez, Camilo; Burken, Joel G

2013-08-20

Tree sampling methods have been used in phytoscreening applications to delineate contaminated soil and groundwater, augmenting traditional investigative methods that are time-consuming, resource-intensive, invasive, and costly. In the past decade, contaminant concentrations in tree tissues have been shown to reflect the extent and intensity of subsurface contamination. This paper investigates a new phytoscreening tool: directional tree coring, a concept originating from field data that indicated azimuthal concentrations in tree trunks reflected the concentration gradients in the groundwater around the tree. To experimentally test this hypothesis, large diameter trees were subjected to subsurface contaminant concentration gradients in a greenhouse study. These trees were then analyzed for azimuthal concentration gradients in aboveground tree tissues, revealing contaminant centroids located on the side of the tree nearest the most contaminated groundwater. Tree coring at three field sites revealed sufficiently steep contaminant gradients in trees reflected nearby groundwater contaminant gradients. In practice, trees possessing steep contaminant gradients are indicators of steep subsurface contaminant gradients, providing compass-like information about the contaminant gradient, pointing investigators toward higher concentration regions of the plume.

Using Tracer Technology to Characterize Contaminated Pipelines

Energy Technology Data Exchange (ETDEWEB)

Maresca, Joseph, W., Jr., Ph.D.; Bratton, Wesley, L., Ph.D., P.E.; Dickerson, Wilhelmina; Hales, Rochelle

2005-12-30

The Pipeline Characterization Using Tracers (PCUT) technique uses conservative and partitioning, reactive or other interactive tracers to remotely determine the amount of contaminant within a run of piping or ductwork. The PCUT system was motivated by a method that has been successfully used to characterize subsurface soil contaminants and is similar in operation to that of a gas chromatography column. By injecting a ?slug? of both conservative and partitioning tracers at one end (or section) of the piping and measuring the time history of the concentration of the tracers at the other end (or another section) of the pipe, the presence, location, and amount of contaminant within the pipe or duct can be determined. The tracers are transported along the pipe or duct by a gas flow field, typically air or nitrogen, which has a velocity that is slow enough so that the partitioning tracer has time to interact with the contaminant before the tracer slug completely passes over the contaminate region. PCUT not only identifies the presence of contamination, it also can locate the contamination along the pipeline and quantify the amount of residual. PCUT can be used in support of deactivation and decommissioning (D&D) of piping and ducts that may have been contaminated with hazardous chemicals such as chlorinated solvents, petroleum products, radioactive materials, or heavy metals, such as mercury.

Water Contamination

Science.gov (United States)

... Statistics Training & Education Policy & Recommendations Fast Facts Healthy Water Sites Healthy Water Drinking Water Healthy Swimming Global ... type=”submit” value=”Submit” /> Healthy Water Home Water Contamination Recommend on Facebook Tweet Share Compartir On ...

Dismantling an alpha-contaminated facility

International Nuclear Information System (INIS)

Caldwell, R.D.; Harper, R.M.

1975-01-01

The difficult task of removing large pieces of highly contaminated equipment from an obsolete plutonium-239 facility was completed in a seven-month operation that included structural alteration of the process building. Detailed job planning, job execution and contamination control were major factors in accomplishing the task

Prohibited Contaminants in Dietary Supplements.

Science.gov (United States)

Mathews, Neilson M

With the increasing use of unregulated dietary supplements, athletes are at continued risk from adverse medical events and inadvertent doping. A review of Clinical Key, MEDLINE, and PubMed databases from 2012 to 2017 was performed using search terms, including dietary supplement, contamination, doping in athletes, inadvertent doping, and prohibited substances. The references of pertinent articles were reviewed for other relevant sources. Clinical review. Level 3. Poor manufacturing processes and intentional contamination with many banned substances continue to occur in dietary supplements sold in the United States. Certain sectors, such as weight loss and muscle-building supplements, pose a greater threat because they are more likely to be contaminated. Athletes will continue to be at risk for adverse events and failed doping tests due to contaminated dietary supplements until legislation changes how they are regulated. In the interim, there are several steps that can be taken to mitigate this risk, including improved education of medical staff and athletes and use of third party-certified products.

Meaning and Mental Contamination: Focus on Appraisals

Science.gov (United States)

Elliott, Corinna M.; Radomsky, Adam S.

2013-01-01

Background: The recent expansion of interest in contamination-related obsessive-compulsive disorder (OCD) has fostered the description of mental contamination and a series of experiments designed to understand associated factors. This supports a cognitive approach to the understanding and treatment of contamination-related OCD--especially when the…

The Induction of Mental and Contact Contamination

Science.gov (United States)

Lee, Michelle; Shafran, Roz; Burgess, Charlotte; Carpenter, Jodi; Millard, Emma; Thorpe, Susan

2013-01-01

Background: Extreme fear of contamination within obsessive compulsive disorder (OCD) is traditionally conceptualised as a physical phenomenon. More recent research has supported the notion of "mental" contamination (MC) in which people feel contaminated in the absence of physical contact. The current research sought to determine whether…

10 CFR 39.69 - Radioactive contamination control.

Science.gov (United States)

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Radioactive contamination control. 39.69 Section 39.69... Radiation Safety Requirements § 39.69 Radioactive contamination control. (a) If the licensee detects evidence that a sealed source has ruptured or licensed materials have caused contamination, the licensee...

Automatic personnel contamination monitor

International Nuclear Information System (INIS)

Lattin, Kenneth R.

1978-01-01

United Nuclear Industries, Inc. (UNI) has developed an automatic personnel contamination monitor (APCM), which uniquely combines the design features of both portal and hand and shoe monitors. In addition, this prototype system also has a number of new features, including: micro computer control and readout, nineteen large area gas flow detectors, real-time background compensation, self-checking for system failures, and card reader identification and control. UNI's experience in operating the Hanford N Reactor, located in Richland, Washington, has shown the necessity of automatically monitoring plant personnel for contamination after they have passed through the procedurally controlled radiation zones. This final check ensures that each radiation zone worker has been properly checked before leaving company controlled boundaries. Investigation of the commercially available portal and hand and shoe monitors indicated that they did not have the sensitivity or sophistication required for UNI's application, therefore, a development program was initiated, resulting in the subject monitor. Field testing shows good sensitivity to personnel contamination with the majority of alarms showing contaminants on clothing, face and head areas. In general, the APCM has sensitivity comparable to portal survey instrumentation. The inherit stand-in, walk-on feature of the APCM not only makes it easy to use, but makes it difficult to bypass. (author)

Contamination of water resources by pathogenic bacteria

Science.gov (United States)

2014-01-01

Water-borne pathogen contamination in water resources and related diseases are a major water quality concern throughout the world. Increasing interest in controlling water-borne pathogens in water resources evidenced by a large number of recent publications clearly attests to the need for studies that synthesize knowledge from multiple fields covering comparative aspects of pathogen contamination, and unify them in a single place in order to present and address the problem as a whole. Providing a broader perceptive of pathogen contamination in freshwater (rivers, lakes, reservoirs, groundwater) and saline water (estuaries and coastal waters) resources, this review paper attempts to develop the first comprehensive single source of existing information on pathogen contamination in multiple types of water resources. In addition, a comprehensive discussion describes the challenges associated with using indicator organisms. Potential impacts of water resources development on pathogen contamination as well as challenges that lie ahead for addressing pathogen contamination are also discussed. PMID:25006540

Desorption and bioremediation of hydrocarbon contaminated soils

International Nuclear Information System (INIS)

Gray, M.R.

1998-01-01

A study was conducted in which the extent and pattern of contaminant biodegradation during bioremediation of four industrially-contaminated soils were examined to determine which factors control the ultimate extent of biodegradation and which limit the success of biological treatment. It was noted that although bioremediation is inexpensive and has low environmental impact, it often fails to completely remove the hydrocarbons in soils because of the complex interactions between contaminants, the soil environment, and the active microorganisms. In this study, the competency of the microorganisms in the soil to degrade the contaminants was examined. The equilibrium partitioning of the contaminants between the soil and the aqueous phase was also examined along with the transport of contaminants out of soil particles. The role of diffusion of compounds in the soil and the importance of direct contact between microorganisms and the hydrocarbons was determined. Methods for selecting suitable sites for biological treatment were also described

Waste management of actinide contaminated soil

International Nuclear Information System (INIS)

Navratil, J.D.; Thompson, G.H.; Kochen, R.L.

1978-01-01

Waste management processes have been developed to reduce the volume of Rocky Flats soil contaminated with plutonium and americium and to prepare the contaminated fraction for terminal storage. The primary process consists of wet-screening. The secondary process uses attrition scrubbing and wet screening with additives. The tertiary process involves volume reduction of the contaminated fraction by calcination, or fixation by conversion to glass. The results of laboratory scale testing of the processes are described

Abnormal ''Contamination' Levels On Garden Appliances

International Nuclear Information System (INIS)

German, U.; Levinson, S.; Elmelech, V.; Pelled, O.; Tshuva, A.; Laichter, Y.

1999-01-01

During routine contamination checks we encountered an abnormal high level of Alpha and Beta emitting radioisotopes on working gloves of employees of the gardening department. It came out that the source was due to ''contamination'' levels on steering wheels of some gardening machines. In order to ensure that no real contamination of these workers was involved , a series of checks was started to identity the source of the abnormal levels found during monitoring

Radiation surveys in contaminated communities

International Nuclear Information System (INIS)

Knight, G.B.

1977-01-01

Radiation surveys of uranium contamination in Uranium City and Port Hope, Canada, are described. Samples of soil, water, and crops grown in contaminated soil and air in homes were analyzed for radon content. Following decontamination, measurements were made of γ exposure rates both inside and outside of buildings

Contaminated land in Colombia: A critical review of current status and future approach for the management of contaminated sites.

Science.gov (United States)

Arias Espana, Victor Andres; Rodriguez Pinilla, Alfonso R; Bardos, Paul; Naidu, Ravi

2018-03-15

Environmental contaminants can have negative effects on human health and land, air and water resources. Consequently, there have been significant advances in regulation for protecting the environment in developed countries including the development of remediation frameworks and guidelines. On the other hand, fewer studies have been reported on the risks and health effects of contaminants in developing regions and there is scarce information regarding contaminated land assessment and environmental remediation. Colombia is an important emerging economy and has started to take the first steps towards the development of a framework for the management of contaminated sites and there are opportunities for the country to learn from countries with well-established frameworks such as the United States (US) and the United Kingdom (UK) and for international collaboration with organisations such as CRC for Contamination Assessment and Remediation of the Environment (CARE). We review main pollution issues, current status of contaminated land management in Colombia to identify the gaps in policy and regulation. We also review the UK and US contaminated land policies and regulations to identify the elements of those experiences that could support progress in the country. Finally, we propose recommendations (e.g. risk based approach, soil screening criteria, clean-up funding, liability) for Colombia that could support further development and implementation of a more effective contaminated land management framework. Copyright © 2017 Elsevier B.V. All rights reserved.

Catalyst Substrates Remove Contaminants, Produce Fuel

Science.gov (United States)

2012-01-01

A spacecraft is the ultimate tight building. We don t want any leaks, and there is very little fresh air coming in, says Jay Perry, an aerospace engineer at Marshall Space Flight Center. As a result, there is a huge potential for a buildup of contaminants from a host of sources. Inside a spacecraft, contaminants can be introduced from the materials that make spacecraft components, electronics boxes, or activities by the crew such as food preparation or cleaning. Humans also generate contaminants by breathing and through the body s natural metabolic processes. As part of the sophisticated Environmental Control and Life Support System on the International Space Station (ISS), a trace contaminant control system removes carbon dioxide and other impurities from the cabin atmosphere. To maintain healthy levels, the system uses adsorbent media to filter chemical contaminant molecules and a high-temperature catalytic oxidizer to change the chemical structure of the contaminants to something more benign, usually carbon dioxide and water. In the 1990s, while researching air quality control technology for extended spaceflight travel, Perry and others at Marshall were looking for a regenerable process for the continuous removal of carbon dioxide and trace chemical contaminants on long-duration manned space flights. At the time, the existing technology used on U.S. spacecraft could only be used once, which meant that a spacecraft had to carry additional spare parts for use in case the first one was depleted, or the spacecraft would have to return to Earth to exchange the components.

Assessment of molecular contamination in mask pod

Science.gov (United States)

Foray, Jean Marie; Dejaune, Patrice; Sergent, Pierre; Gough, Stuart; Cheung, D.; Davenet, Magali; Favre, Arnaud; Rude, C.; Trautmann, T.; Tissier, Michel; Fontaine, H.; Veillerot, M.; Avary, K.; Hollein, I.; Lerit, R.

2008-04-01

Context/ study Motivation: Contamination and especially Airbone Molecular Contamination (AMC) is a critical issue for mask material flow with a severe and fairly unpredictable risk of induced contamination and damages especially for 193 nm lithography. It is therefore essential to measure, to understand and then try to reduce AMC in mask environment. Mask material flow was studied in a global approach by a pool of European partners, especially within the frame of European MEDEA+ project, so called "MUSCLE". This paper deals with results and assessment of mask pod environment in term of molecular contamination in a first step, then in a second step preliminary studies to reduce mask pod influence and contamination due to material out gassing. Approach and techniques: A specific assessment of environmental / molecular contamination along the supply chain was performed by all partners. After previous work presented at EMLC 07, further studies were performed on real time contamination measurement pod at different sites locations (including Mask manufacturing site, blank manufacturing sites, IC fab). Studies were linked to the main critical issues: cleaning, storage, handling, materials and processes. Contamination measurement campaigns were carried out along the mask supply chain using specific Adixen analyzer in order to monitor in real time organic contaminants (ppb level) in mask pods. Key results would be presented: VOC, AMC and humidity level on different kinds of mask carriers, impact of basic cleaning on pod outgassing measurement (VOC, NH3), and process influence on pod contamination... In a second step, preliminary specific pod conditioning studies for better pod environment were performed based on Adixen vacuum process. Process influence had been experimentally measured in term of molecular outgassing from mask pods. Different AMC experimental characterization methods had been carried out leading to results on a wide range of organic and inorganic

10 CFR 20.1406 - Minimization of contamination.

Science.gov (United States)

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Minimization of contamination. 20.1406 Section 20.1406... License Termination § 20.1406 Minimization of contamination. (a) Applicants for licenses, other than early... procedures for operation will minimize, to the extent practicable, contamination of the facility and the...

Monitoring of transport contamination

International Nuclear Information System (INIS)

Turkin, N.F.

1980-01-01

Organization of monitoring of transport contamination is considered. A particularly thorough monitoring is recommended to be carried out in loading-unloading operations. The monitoring is performed when leaving loading-unloading site and zone under control and prior to preventive examination, technical service or repair. The method of monitoring of auto transport contamination with high-energy β-emitters by means of a special stand permitting the automation of the monitoring process is described [ru

Analysis and characterization of contamination in EUV reticles

Science.gov (United States)

Okoroanyanwu, Uzodinma; Dittmar, Kornelia; Fahr, Torsten; Wallow, Tom; La Fontaine, Bruno; Wood, Obert; Holfeld, Christian; Bubke, Karsten; Peters, Jan-Hendrik

2010-04-01

A host of complementary imaging techniques (Scanning Electron Microscopy), surface analytical technique (Auger Electron Spectroscopy, AES), chemical analytical and speciation techniques (Grazing Incidence Reflectance Fourier-Transform Infrared Spectroscopy, GIR-FTIR; and Raman spectroscopy) have been assessed for their sensitivity and effectiveness in analyzing contamination on three EUV reticles that were contaminated to varying degrees. The first reticle was contaminated as a result of its exposure experience on the SEMATECH EUV Micro Exposure Tool (MET) at Lawrence Berkeley National Laboratories, where it was exposed to up to 80 hours of EUV radiation. The second reticle was a full-field reticle, specifically designed to monitor molecular contamination, and exposed to greater than 1600J/cm2 of EUV radiation on the ASML Alpha Demo Tool (ADT) in Albany Nanotech in New York. The third reticle was intentionally contaminated with hydrocarbons in the Microscope for Mask Imaging and Contamination Studies (MIMICS) tool at the College of Nanoscale Sciences of State University of New York at Albany. The EUV reflectivities of some of these reticles were measured on the Advanced Light Source EUV Reflectomer at Lawrence Berkeley National Laboratories and PTB Bessy in Berlin, respectively. Analysis and characterization of thin film contaminants on the two EUV reticles exposed to varying degrees of EUV radiation in both MET and ADT confirm that the two most common contamination types are carbonization and surface oxidation, mostly on the exposed areas of the reticle, and with the MET being significantly more susceptible to carbon contamination than the ADT. While AES in both surface scanning and sputter mode is sensitive and efficient in analyzing thin contaminant films (of a few nanometers), GIRFTIR is sensitive to thick films (of order of a 100 nm or more on non-infra-red reflecting substrates), Raman spectroscopy is not compatible with analyzing such contaminants because of

Phytoextraction of low level U-contaminated soil

International Nuclear Information System (INIS)

Vandenhove, H.A.; Hees, M. van

2002-01-01

The nuclear fuel cycle may be a source of environmental contamination. Uranium exploitation produces large quantities of wastes but also accidental spills at nuclear fuel production, reprocessing or waste treatment plants have led to soil contamination with uranium. U-contaminated soil is generally excavated, packaged and removed which is a costly enterprise. Soil washing has also shown promising in removing U from contaminated soil, but results in the generation of liquid wastes and the deterioration of soil properties. In contrast, phytoextraction, the use of plants to remove contaminants from polluted soil, allows for in situ treatment and does not generate liquid wastes. Furthermore, the contaminated site is covered by plants during phytoextraction and wind and water erosion will be reduced. The phytoextraction potential depends on the amount of radionuclides extracted and the biomass produced. Hyper-accumulating plants often have a low biomass production. Moreover, uranium soil-to-plant transfer factors (TF: ratio of U concentration in dry plant tissue to concentration in soil) rarely exceed a value of 0.1 gg -1 . With a TF of 0.1 gg -1 and a biomass yield of 15t dry weigh ha -1 only 0.1% of the soil uranium will be annually immobilised in the plant biomass. These figures clearly show that the phytoextraction option is not a feasible remediation option, unless the uranium bioavailability could be drastically increased. It was shown that citric acid addition to highly contaminated U contaminated soil increased the U-accumulation of Brassica juncea 1000-fold. The objective of the present paper is to find out if low level U contaminated soil can be phytoextracted in order to achieve proposed release limits

Management of internal contamination accidents

International Nuclear Information System (INIS)

Lipsztein, J.L.; Melo, D.R.

1997-01-01

This paper concerns with the techniques for intakes assessment which depend on the mode and level of intake, the type of energy of the radiation emitted, the biokinetic of the contaminant, and the sensitivity and availability of measurement facilities. In vivo and in vitro techniques are used to quantify internal contaminations

Experimental increase in availability of a PAH complex organic contamination from an aged contaminated soil: Consequences on biodegradation

International Nuclear Information System (INIS)

Cébron, Aurélie; Faure, Pierre; Lorgeoux, Catherine; Ouvrard, Stéphanie; Leyval, Corinne

2013-01-01

Although high PAH content and detection of PAH-degraders, the PAH biodegradation is limited in aged-contaminated soils due to low PAH availability (i.e., 1%). Here, we tried to experimentally increase the soil PAH availability by keeping both soil properties and contamination composition. Organic extract was first removed and then re-incorporated in the raw soil as fresh contaminants. Though drastic, this procedure only allowed a 6-time increase in the PAH availability suggesting that the organic constituents more than ageing were responsible for low availability. In the re-contaminated soil, the mineralization rate was twice more important, the proportion of 5–6 cycles PAH was higher indicating a preferential degradation of lower molecular weight PAH. The extraction treatment induced bacterial and fungal community structures modifications, Pseudomonas and Fusarium solani species were favoured, and the relative quantity of fungi increased. In re-contaminated soil the percentage of PAH-dioxygenase gene increased, with 10 times more Gram negative representatives. -- Highlights: ► Re-incorporation of soil organic extract increased 6-times the PAH availability. ► Complexity of organic contamination is the main driver of PAH availability. ► Biodegradation of PAH with less than 5-cycles increased with increasing PAH availability. ► Pseudomonas and Fusarium species are favoured when PAH availability increased. -- More than ageing, the complexity of organic contamination is the main driver of PAH availability

Contamination effects on fixed-bias Langmuir probes

Energy Technology Data Exchange (ETDEWEB)

Steigies, C. T. [Institut fuer Experimentelle und Angewandte Physik, Christian-Albrechts-Universitaet zu Kiel, 24098 Kiel (Germany); Barjatya, A. [Department of Physical Sciences, Embry-Riddle Aeronautical University, Daytona Beach, Florida 32114 (United States)

2012-11-15

Langmuir probes are standard instruments for plasma density measurements on many sounding rockets. These probes can be operated in swept-bias as well as in fixed-bias modes. In swept-bias Langmuir probes, contamination effects are frequently visible as a hysteresis between consecutive up and down voltage ramps. This hysteresis, if not corrected, leads to poorly determined plasma densities and temperatures. With a properly chosen sweep function, the contamination parameters can be determined from the measurements and correct plasma parameters can then be determined. In this paper, we study the contamination effects on fixed-bias Langmuir probes, where no hysteresis type effect is seen in the data. Even though the contamination is not evident from the measurements, it does affect the plasma density fluctuation spectrum as measured by the fixed-bias Langmuir probe. We model the contamination as a simple resistor-capacitor circuit between the probe surface and the plasma. We find that measurements of small scale plasma fluctuations (meter to sub-meter scale) along a rocket trajectory are not affected, but the measured amplitude of large scale plasma density variation (tens of meters or larger) is attenuated. From the model calculations, we determine amplitude and cross-over frequency of the contamination effect on fixed-bias probes for different contamination parameters. The model results also show that a fixed bias probe operating in the ion-saturation region is affected less by contamination as compared to a fixed bias probe operating in the electron saturation region.

Groundwater recharge and agricultural contamination

Science.gov (United States)

Böhlke, J.K.

2002-01-01

Agriculture has had direct and indirect effects on the rates and compositions of groundwater recharge and aquifer biogeochemistry. Direct effects include dissolution and transport of excess quantities of fertilizers and associated materials and hydrologic alterations related to irrigation and drainage. Some indirect effects include changes in water–rock reactions in soils and aquifers caused by increased concentrations of dissolved oxidants, protons, and major ions. Agricultural activities have directly or indirectly affected the concentrations of a large number of inorganic chemicals in groundwater, for example NO3–, N2, Cl, SO42–, H+, P, C, K, Mg, Ca, Sr, Ba, Ra, and As, as well as a wide variety of pesticides and other organic compounds. For reactive contaminants like NO3–, a combination of chemical, isotopic, and environmental-tracer analytical approaches might be required to resolve changing inputs from subsequent alterations as causes of concentration gradients in groundwater. Groundwater records derived from multi-component hydrostratigraphic data can be used to quantify recharge rates and residence times of water and dissolved contaminants, document past variations in recharging contaminant loads, and identify natural contaminant-remediation processes. These data indicate that many of the world's surficial aquifers contain transient records of changing agricultural contamination from the last half of the 20th century. The transient agricultural groundwater signal has important implications for long-term trends and spatial heterogeneity in discharge.

Radiocesium contamination and the reindeer

International Nuclear Information System (INIS)

Eriksson, O.; Raunistola, T.; Jones, B.E.V.

1991-01-01

The high transfer factors calculated for radiocesium in this study are partly due to the feeding habits of the reindeer with a substantial intake of lichens, especially in the wintertime. Seasonal changes in grazing plant selection caused a considerable cyclic, seasonal variation in radiocesium content of soft tissues. The effective half-life of radiocesium in reindeer during winter feeding conditions was determined to about 30 days in an experiment where a herd of reindeer was moved from a high (> 20 kBq/m 2 Cs-137) to a low (> 3 kBq/m 2 Cs-137) contamination area. During natural grazing conditions the fractional transfer of Cs-137 was determined to about 0.65 d/kg during wintertime in the low-contamination area and about 0.30 d/kg in summertime after grazing on highly contaminated pastures. The effective half-life of Cs-137 in reindeer lichens was seven to ten years both before and after the Chernobyl accident. In areas with initially high contamination the half-life was shorter, 6.2±0.9 years, than in areas with lower contamination, 15.0 ± 5.1 years. In heather, bilberry and crowberry negative effective half-lives, increasing concentrations, were observed. Precipitation during the growth period could change the Cs-137 activity of some plant species. (au) (32 refs.)

Process for affixing radioactive contamination on contaminated materials or wastes. Its application

International Nuclear Information System (INIS)

Aubouin, Guy; Aude, Georges; Tassigny, Christian de.

1982-01-01

The invention concerns a process for affixing radioactive contamination on materials or waste matter in order to ensure that the materials are transferred in complete safety or to package them when their activity is low. Under this process at least one coat of a resin polymerizable at ambient temperature, for example an epoxy resin, a polyester resin, a vinyl resin or a mixture of thermohardening resin and thermoplastic resin, is sprayed on to the contaminated material part by means of an electrostatic gun [fr

Monitoring of overalls and personnel skin contamination

International Nuclear Information System (INIS)

Turkin, N.F.

1980-01-01

Organization of monitoring of overalls and personnel skin contamination wastes is considered. The devices used for this purpose are enumerated. In sanitary sluices through which the personnel leaving the repair zone it is recommended to particularly thoroughly control hand skin contamination and most contaminated parts of overalls (sleeves, breeches lower parts, pockets, stomack region). In sanitary check points during personnel leaving the operator zone monitoring of overalls and skin contamination is performed. The overalls and other individual protective clothing are subjected to control in a special loundry before and after washing (decontamination) [ru

49 CFR 177.843 - Contamination of vehicles.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Contamination of vehicles. 177.843 Section 177.843... and Unloading § 177.843 Contamination of vehicles. (a) Each motor vehicle used for transporting Class... surface contamination is not greater than the level prescribed in § 173.443(a) of this subchapter. (b...

Contamination Sensitivity in Young Children.

Science.gov (United States)

Siegal, Michael; Share, David L.

1990-01-01

Revealed that children were able to indicate that an apparently safe substance such as juice may be contaminated by contact with a foreign body such as a cockroach. Supported the hypothesis that early sensitivity to substances that contain invisible contaminates may be guided by knowledge of a distinction between appearance and reality. (RH)

Integrating Individual-Based Indices of Contaminant Effects

Directory of Open Access Journals (Sweden)

Christopher L. Rowe

2001-01-01

Full Text Available Habitat contamination can alter numerous biological processes in individual organisms. Examining multiple individual-level responses in an integrative fashion is necessary to understand how individual health or fitness reflects environmental contamination. Here we provide an example of such an integrated perspective based upon recent studies of an amphibian (the bullfrog, Rana catesbeiana that experiences several, disparate changes when larval development occurs in a trace element�contaminated habitat. First, we present an overview of studies focused on specific responses of individuals collected from, or transplanted into, a habitat contaminated by coal combustion residues (CCR. These studies have reported morphological, behavioral, and physiological modifications to individuals chronically interacting with sediments in the CCR-contaminated site. Morphological abnormalities in the oral and tail regions in contaminant-exposed individuals influenced other properties such as grazing, growth, and swimming performance. Behavioral changes in swimming activities and responses to stimuli appear to influence predation risk in the contaminant-exposed population. Significant changes in bioenergetics in the contaminated habitat, evident as abnormally high energetic expenditures for survival (maintenance costs, may ultimately influence production pathways (growth, energy storage in individuals. We then present a conceptual model to examine how interactions among the affected systems (morphological, behavioral, physiological may ultimately bring about more severe effects than would be predicted if the responses were considered in isolation. A complex interplay among simultaneously occurring biological changes emerges in which multiple, sublethal effects ultimately can translate into reductions in larval or juvenile survival, and thus reduced recruitment of juveniles into the population. In systems where individuals are exposed to low concentrations of

Remediation of contaminated areas. An overview of international guidance

DEFF Research Database (Denmark)

Jensen, Per Hedemann

1999-01-01

techniques as a function of contamination and site characteristics. The project includes analyses of existing remediation methodologies and contaminated sites, and is structured in the following steps:-characterisation of relevant contaminated sites -identification and characterisation of relevant...... contaminated with radioactive materials as a result of the operation of these installations. The areasconsidered for remedial measures include contaminated land areas, rivers and sediments in rivers, lakes, and sea areas. Criteria for clean-up of contaminated land and criteria for protection of the public...

Th biodistribution in internal contamination of animals

International Nuclear Information System (INIS)

Ciubotariu, M.; Danis, A.; Dumitrescu, G.; Cucu, M.

1999-01-01

Fissionable elements (U,Th) internal contamination have been studied using the fission track method as analysis method of the U and/or Th contaminant elements and Wistar-London breed rats as experiment animals. Different ways to obtain internal contaminations have been investigated: ingestion, inhalation, absorption by skin and through wounds. After the U internal contamination study was carried out, in this stage the Th internal contamination by ingestion is in progress. Using the identical aliquot parts of a solution calibrated in Th, corresponding to an Annual Limit Intake, three Wistar-London breed rats were contaminated. They were kept in normal life conditions and under permanent medical surveillance up to their sacrification. The animals were sacrificed at different time intervals after their contamination: 2 days, 7 days and 14 days, respectively. After the sacrification, their vital organs were sampled, weighed, calcined, re-weighed and finally analysed by track detection using the fission track micro-mappings technique. Also, their evacuations were sampled every 24 hours weighed, calcined and analysed in the same way as the vital organs. The Th fission track micro-mappings technique was used in the following conditions: - mica-muscovite as track detector pre-etched for fossil tracks 18 h in HF-40 per cent at room temperature; - the neutron irradiations were performed in the nuclear reactor VVR-S Bucharest at the neutron fluences of 3.10 15 - 2.10 16 fast neutrons/c m 2 ; - the visualization of the Th induced fission tracks were obtained by chemical etching in HF-40 per cent, 3 h at room temperature; - the Th track micro-mappings obtained in track detectors were studied by optical microscopy using a stereo microscope WILD M7S for ensemble study (X6-X31) and a binocular ZEISS JENA microscope for qualitative and quantitative studies (X150). The biological reference materials calibrated in Th were prepared in our laboratory using the calcined organs and the

Uranium-contaminated soil pilot treatment study

International Nuclear Information System (INIS)

Turney, W.R.J.R.; Mason, C.F.V.; Michelotti, R.A.

1996-01-01

A pilot treatment study is proving to be effective for the remediation of uranium-contaminated soil from a site at the Los Alamos National Laboratory by use of a two-step, zero-discharge, 100% recycle system. Candidate uranium-contaminated soils were characterized for uranium content, uranium speciation, organic content, size fractionization, and pH. Geochemical computer codes were used to forecast possible uranium leach scenarios. Uranium contamination was not homogenous throughout the soil. In the first step, following excavation, the soil was sorted by use of the ThemoNuclean Services segmented gate system. Following the sorting, uranium-contaminated soil was remediated in a containerized vat leach process by use of sodium-bicarbonate leach solution. Leach solution containing uranium-carbonate complexes is to be treated by use of ion-exchange media and then recycled. Following the treatment process the ion exchange media will be disposed of in an approved low-level radioactive landfill. It is anticipated that treated soils will meet Department of Energy site closure guidelines, and will be given open-quotes no further actionclose quotes status. Treated soils are to be returned to the excavation site. A volume reduction of contaminated soils will successfully be achieved by the treatment process. Cost of the treatment (per cubic meter) is comparable or less than other current popular methods of uranium-contamination remediation

Decontamination method and device for radiation contaminated product

International Nuclear Information System (INIS)

Morikawa, Kenji; Ohinata, Hiroshi; Omata, Kazuo; Sato, Toshihiko; Nakajima, Yoshihiko; Ichikawa, Seigo.

1996-01-01

In the present invention, radiation contaminated products generated during shot peening are decontaminated by a chelating agent, and the chelating agent is removed from the radiation contaminated products. Then the temperature of the radiation contaminated products is elevated by hot blowing at a temperature higher than a boiling point of the solvent. Then, a solvent is added to the radiation contaminated products and the solvent is evaporated abruptly. The solution of the chelating agent remained while being deposited thereto is removed by evaporation to remove it from the radiation contaminated products together with the solvent. With such procedures, all of the decontamination steps can be completed in one device without requiring a large space or not moving the radiation contaminated products on every step. (T.M.)

Chemical fingerprinting of hydrocarbon-contamination in soil

DEFF Research Database (Denmark)

Boll, Esther Sørensen; Nejrup, Jens; Jensen, Julie K.

2015-01-01

Chemical fingerprinting analyses of 29 hydrocarbon-contaminated soils were performed to assess the soil quality and determine the main contaminant sources. The results were compared to an assessment based on concentrations of the 16 priority polycyclic aromatic hydrocarbons pointed out by the U...... and in assessing weathering trends of hydrocarbon contamination in the soils. Multivariate data analysis of sum-normalized concentrations could as a stand-alone tool distinguish between hydrocarbon sources of petrogenic and pyrogenic origin, differentiate within petrogenic sources, and detect weathering trends....... Diagnostic ratios of PACs were not successful for source identification of the heavily weathered hydrocarbon sources in the soils. The fingerprinting of contaminated soils revealed an underestimation of PACs in petrogenic contaminated soils when the assessment was based solely on EPAPAH16. As alkyl...

Radiation protection of radioactively contaminated large areas by phytoremediation and subsequent utilization of the contaminated plant residues (PHYTOREST)

International Nuclear Information System (INIS)

Mirgorodsky, Daniel; Ollivier, Delphine; Merten, Dirk; Bergmann, Hans; Buechel, Georg; Willscher, Sabine; Wittig, Juliane; Jablonski, Lukasz; Werner, Peter

2010-01-01

Much progress has been achieved over the past 20 years in remediating sites contaminated by heavy metal. However, very large contaminated areas have presented major problems to this day because of remediation costs. Phytoremediation is a new, emerging, sustainable technique of remediating areas with low heavy-metal contamination. One advantage of phytoremediation is the comparatively low cost of the process, which may make it usable also on large areas with low levels of contamination. Besides extracting and immobilizing metals, respectively, phytoremediation among other things also contributes to improving soil quality in terms of physics, chemistry, and ecology. Consequently, phytoremediation offers a great potential for the future. Research into phytoremediation of an area contaminated by heavy metals and radionuclides is carried out on a site in a former uranium mining district in Eastern Thuringia jointly by the Friedrich Schiller University, Jena, and the Technical University of Dresden in a project funded by the German Federal Ministry for Education and Research. The project serves to promote the introduction of soft, biocompatible methods of long-term remediation and to develop conceptual solutions to the subsequent utilization of contaminated plant residues. Optimizing area management is in the focus of phytoremediation studies. (orig.)

Substantiation of the permissible radioactive contamination of working clothes

International Nuclear Information System (INIS)

Shcherbakov, V.L.; Korostin, A.S.

1977-01-01

A permissible level of working clothes contamination was determined on the base of the main migration routes of radioactive contaminants: permeation directly through the clothes into subclothes space on skin surface, emission into the air with amount of contaminants subsequently got by the organism of a working person through inhalation as well as transfer in the process of contacting of contaminated working clothes and surfaces of premises equipment, working person hands with amount of contaminants posteriorly got by the organism by alimentary or inhalation ways. Using the experimental and literature data available the permissible levels of working clothes contamination for the mentioned migration routes of radioactive materials have been calculated. According to the data obtained the permissible levels of working clothes contamination must not exceed 4 alpha-part/(cm 2 xmin) for contamination with high-tonic isotopes, 20 alpha-part./(cm 2 xmin) with other alpha-detine isotopes, 1000 beta-part./(cm 2 xmin) with beta-active ones. The permissible level of contamination of additional materials of the individual protection in the case of their contamination with high-tonic alpha-actine isotopes must not exceed 50 alpha-part./(cm 2 xmin), 200 alpha-part./(cm 2 xmin) for contamination th other alpha-active isotopes and 400 beta-part./(cm 2 xmin) with beta-active isotopes

Cotton contamination

CSIR Research Space (South Africa)

Van der Sluijs, MHJ

2018-05-01

Full Text Available This review focusses on physical forms of contaminant including the presence, prevention and/or removal of foreign bodies, stickiness and seed-coat fragments rather than the type and quantity of chemical residues that might be present in cotton...

Characterisation of contamination migration in the workplace

International Nuclear Information System (INIS)

Boulaud, D.; Laborde, J.C.; Pourprix, M.

1994-01-01

The Institute for Nuclear Safety and Protection (IPSN) has developed a procedure for characterising airborne contamination between processes and the workplace in nuclear facilities. It was initially intended to use this process to validate operator choices concerning the monitoring of indoor air contamination (personnel monitoring, and environmental detection at fixed locations), but also to optimise the fundamental parameters which have a more or less direct influence on potential exposure of staff in the workplace (at the same time optimising the contamination source, close confinement, process ventilation and general ventilation). In practice, the methods used to obtain these expert appraisals were usually based on experiments carried out in situ: (i) characterisation of aerosol contamination by accurate measurement of the nature, concentration and particle size distribution at various locations; (ii) characterisation of the migration of contamination by precise measurement involving gas and/or particle tracing techniques. In parallel with these experiments, a considerable effort was made to develop and qualify computer codes capable of predicting or estimating the migration of contamination through complex ventilated areas, by means of both fluid mechanics and aerosol science. (Author)

Radiation. Basics, influences, contamination situation, and countermeasures

International Nuclear Information System (INIS)

Baba, Mamoru; Nomura, Kiyoshi

2012-01-01

Fukushima Daiichi Nuclear Accident resulted in the contamination of a large area, and by now the situation of contamination and exposure has gradually clarified, and a lot of information has been being accumulated. Toward reconstruction of Fukushima prefecture from the current circumstance that the residents still live under continuing fear, this article discusses how to clarify the current situation and deal with the contamination, which the residents are concerned about. First, radiation, basic properties of radiation, and so on are introduced. Regarding the influence on human bodies, the mechanism and the degree of influence by radiation, especially on children, women, and pregnant women are explained. Next, regarding the measurements of radiation and radioactivity, the properties of measurement methods and the detectors are explained. Regarding the current situation of contamination and exposure, mainly addressing the area around Koriyama city, various topics are covered including: (1) situation of contamination and radiation monitoring, (2) countermeasures for radioactivity contamination, (3) internal exposure dose, (4) exposed dose from water and food, as well as (5) safety standards. (S.K.)

Materials contamination control in the microelectronic industry; Controle de la contamination des materiaux dans l`industrie de la micro-electronique

Energy Technology Data Exchange (ETDEWEB)

Tardif, F

1994-12-31

This paper deals with many aspects of the contamination of materials in the microelectronic industry. The contamination`s control of chemicals, process gases, silicon and the survey of the ions free water`s purity are treated. (TEC). 29 figs., 7 tabs.

Space station contamination control study: Internal combustion, phase 1

Science.gov (United States)

Ruggeri, Robert T.

1987-01-01

Contamination inside Space Station modules was studied to determine the best methods of controlling contamination. The work was conducted in five tasks that identified existing contamination control requirements, analyzed contamination levels, developed outgassing specification for materials, wrote a contamination control plan, and evaluated current materials of offgassing tests used by NASA. It is concluded that current contamination control methods can be made to function on the Space Station for up to 1000 days, but that current methods are deficient for periods longer than about 1000 days.

Surfactant screening of diesel-contaminated soil

International Nuclear Information System (INIS)

Peters, R.W.; Shem, L.; Montemagno, C.D.; Lewis, B.

1991-01-01

At one installation, approximately 60,000 gal of No. 2 diesel fuel leaked into the subsurface environment, with contamination at depths of 6 to 34 m below the surface. Argonne National Laboratory was contracted to perform treatability studies for site remediation. The treatability studies focused on four separate phases: (1) leachability studies on the various contaminated soil borings, (2) air stripping studies, (3) bioremediation studies, and (4) surfactant screening/surfactant flooding studies. This paper summarizes the fourth phase of the research program in which 21 surfactants were screened for possible use to mobilize the organics from the contaminated soil prior to bioremediation. Anionic surfactants resulted in the greatest degree of diesel mobilization. The most promising surfactants will be employed on actual contaminated soil samples obtained from the site

Modeling Groundwater-Surface Water Interaction and Contaminant Transport of Chlorinated Solvent Contaminated Site

Science.gov (United States)

Yimer Ebrahim, Girma; Jonoski, Andreja; van Griensven, Ann; Dujardin, Juliette; Baetelaan, Okke; Bronders, Jan

2010-05-01

Chlorinated-solvent form one of the largest groups of environmental chemicals. Their use and misuse in industry have lead to a large entry of these chemicals into the environment, resulting in widespread dissemination and oftentimes environmental contamination. Chlorinated solvent contamination of groundwater resources has been widely reported. For instance, there has been much interest in the assessment of these contaminant levels and their evolutions with time in the groundwater body below the Vilvoorde-Machelen industrial area (Belgium). The long industrial history of the area has lead to complex patterns of pollution from multiple sources and the site has been polluted to the extent that individual plumes are not definable any more. Understanding of groundwater/surface water interaction is a critical component for determining the fate of contaminant both in streams and ground water due to the fact that groundwater and surface water are in continuous dynamic interaction in the hydrologic cycle. The interaction has practical consequences in the quantity and quality of water in either system in the sense that depletion and/or contamination of one of the system will eventually affect the other one. The transition zone between a stream and its adjacent aquifer referred to as the hyporheic zone plays a critical role in governing contaminant exchange and transformation during water exchange between the two water bodies. The hyporheic zone of Zenne River ( the main receptor ) is further complicated due to the fact that the river banks are artificially trained with sheet piles along its reach extending some 12 m below the surface. This study demonstrates the use of MODFLOW, a widely used modular three-dimensional block-centred finite difference, saturated flow model for simulating the flow and direction of movement of groundwater through aquifer and stream-aquifer interaction and the use of transport model RT3D, a three-dimensional multi-species reactive transport model

Some problems in calibrating surface contamination meters

International Nuclear Information System (INIS)

Chen Zigen; LI Xingyuan; Shuai Xiaoping.

1984-01-01

It is necessary that instruments are calibrated accurately in order to obtain reliable survey data of surface contamination. Some problems in calibrating surface contamination meters are expounded in this paper. Measurement comparison for beta surface contamination meters is organized within limited scope, thus survey quality is understood, questions are discovered, significance of calibration is expounded further. (Author)

Bonding of radioactive contamination. III. Auger electron spectroscopic investigation

International Nuclear Information System (INIS)

Rankin, W.N.; Whitkop, P.G.

1983-01-01

The mechanisms by which radioactive contamination would be bonded to a DWPF canister surface are being investigated. Tests with low pressure water and air-injected water decontamination of radioactive specimens showed that bonding of contamination increases rapidly with postoxidation temperature. Even with the least severe temperature conditions expected on the waste glass canister, bonding is so great that decontamination cannot be affected by water-only techniques. A preoxidation film increased rather than decreased bonding. This memorandum describes detailed surface analyses of coupons simulating DWPF canister surfaces. Based on this examination we conclude: contamination will be dispersed throughout the oxide film on DWPF canisters. Contamination is concentrated at the surface, decreasing farther into the oxide film; some samples contain sludge contamination at the steel/oxide interface. This was not the case for semi-volatile (Cs 2 O) contamination; in samples with contamination at the steel/oxide interface, at least 80% of the contamination is usually in the oxide layer; no difference in contamination dispersion between preoxidized and non-preoxidized samples was found; and postoxidation atmosphere had no effect on the contamination dispersion within the oxide layer. 6 references, 9 figures

Test installation for separation of contaminated/activated concrete

International Nuclear Information System (INIS)

Klok, H.; Peeze Binkhorst, I.A.G.M.

1993-01-01

Large amounts of contaminated concrete are released when dismantling nuclear power plants. Volume reduction of contaminated concrete has economic and environmental advantages. A test facility has been built by which contaminated concrete can be separated in clean aggregate and contaminated cement. During the tests a considerable amount of dust accumulated in the valve construction of the test installation. This could result in an unacceptable accumulation of contaminated dust, blocking of the handle and emission of dust and grit during the operation of the test facility. The design of the valve construction was adjusted by using and testing flexible materials

Association of leukemia with radium groundwater contamination

International Nuclear Information System (INIS)

Lyman, G.H.; Lyman, C.G.; Johnson, W.

1985-01-01

Radiation exposure, including the ingestion of radium, has been causally associated with leukemia in man. Groundwater samples from 27 counties on or near Florida phosphate lands were found to exceed 5 pCi/L total radium in 12.4% of measurements. The incidence of leukemia was greater in those counties with high levels of radium contamination (greater than 10% of the samples contaminated) than in those with low levels of contamination. Rank correlation coefficients of .56 and .45 were observed between the radium contamination level and the incidence of total leukemia and acute myeloid leukemia, respectively. The standardized incidence density ratio for those in high-contamination counties was 1.5 for total leukemia and 2.0 for acute myeloid leukemia. Further investigation is necessary, however, before a causal relationship between groundwater radium content and human leukemia can be established

Methodology for performing surveys for fixed contamination

International Nuclear Information System (INIS)

Durham, J.S.; Gardner, D.L.

1994-10-01

This report describes a methodology for performing instrument surveys for fixed contamination that can be used to support the release of material from radiological areas, including release to controlled areas and release from radiological control. The methodology, which is based on a fast scan survey and a series of statistical, fixed measurements, meets the requirements of the U.S. Department of Energy Radiological Control Manual (RadCon Manual) (DOE 1994) and DOE Order 5400.5 (DOE 1990) for surveys for fixed contamination and requires less time than a conventional scan survey. The confidence interval associated with the new methodology conforms to the draft national standard for surveys. The methodology that is presented applies only to surveys for fixed contamination. Surveys for removable contamination are not discussed, and the new methodology does not affect surveys for removable contamination

Proposed derivation of skin contamination and skin decontamination limits

International Nuclear Information System (INIS)

Schieferdecker, H.; Koelzer, W.; Henrichs, K.

1986-01-01

From the primary dose limits for the skin, secondary dose limits were derived for skin contamination which can be used in practical radiation protection work. Analogous to the secondary dose limit for the maximum permissible body burden in the case of incorporation, dose limits for the 'maximum permissible skin burden' were calculated, with the help of dose factors, for application in the case of skin contamination. They can be derived from the skin dose limit values. For conditions in which the skin is exposed to temporary contamination, a limit of skin contamination was derived for immediately removable contamination and for one day of exposure. For non-removable contamination a dose limit of annual skin contamination was defined, taking into account the renewal of the skin. An investigation level for skin contamination was assumed, as a threshold, above which certain measures must be taken; these to include appropriate washing not more than three times, with the subsequent procedure determined by the level of residual contamination. The dose limits are indicated for selected radionuclides. (author)

Phytovolatilization of Organic Contaminants.

Science.gov (United States)

Limmer, Matt; Burken, Joel

2016-07-05

Plants can interact with a variety of organic compounds, and thereby affect the fate and transport of many environmental contaminants. Volatile organic compounds may be volatilized from stems or leaves (direct phytovolatilization) or from soil due to plant root activities (indirect phytovolatilization). Fluxes of contaminants volatilizing from plants are important across scales ranging from local contaminant spills to global fluxes of methane emanating from ecosystems biochemically reducing organic carbon. In this article past studies are reviewed to clearly differentiate between direct- and indirect-phytovolatilization and we discuss the plant physiology driving phytovolatilization in different ecosystems. Current measurement techniques are also described, including common difficulties in experimental design. We also discuss reports of phytovolatilization in the literature, finding that compounds with low octanol-air partitioning coefficients are more likely to be phytovolatilized (log KOA < 5). Reports of direct phytovolatilization at field sites compare favorably to model predictions. Finally, future research needs are presented that could better quantify phytovolatilization fluxes at field scale.

Indexing contamination surveys

International Nuclear Information System (INIS)

Brown, R.L.

1998-01-01

The responsibility for safely managing the Tank Farms at Hanford belongs to Lockheed Martin Hanford Corporation which is part of the six company Project Hanford Management Team led by Fluor Daniel Hanford, Inc.. These Tank Farm Facilities contain numerous outdoor contamination areas which are surveyed at a periodicity consistent with the potential radiological conditions, occupancy, and risk of changes in radiological conditions. This document describes the survey documentation and data tracking method devised to track the results of contamination surveys this process is referred to as indexing. The indexing process takes a representative data set as an indicator for the contamination status of the facility. The data are further manipulated into a single value that can be tracked and trended using standard statistical methodology. To report meaningful data, the routine contamination surveys must be performed in a manner that allows the survey method and the data collection process to be recreated. Three key criteria are necessary to accomplish this goal: Accurate maps, consistent documentation, and consistent consolidation of data meeting these criteria provides data of sufficient quality to be tracked. Tracking of survey data is accomplished by converting the individual survey results into a weighted value, corrected for the actual number of survey points. This information can be compared over time using standard statistical analysis to identify trends. At the Tank Farms, the need to track and trend the facility's radiological status presents unique challenges. Many of these Tank Farm facilities date back to the second world war. The Tank Farm Facilities are exposed to weather extremes, plant and animal intrusion, as well as all of the normal challenges associated with handling radiological waste streams. Routine radiological surveys did not provide a radiological status adequate for continuing comparisons

Geophysical Signitures From Hydrocarbon Contaminated Aquifers

Science.gov (United States)

Abbas, M.; Jardani, A.

2015-12-01

The task of delineating the contamination plumes as well as studying their impact on the soil and groundwater biogeochemical properties is needed to support the remediation efforts and plans. Geophysical methods including electrical resistivity tomography (ERT), induced polarization (IP), ground penetrating radar (GPR), and self-potential (SP) have been previously used to characterize contaminant plumes and investigate their impact on soil and groundwater properties (Atekwana et al., 2002, 2004; Benson et al., 1997; Campbell et al., 1996; Cassidy et al., 2001; Revil et al., 2003; Werkema et al., 2000). Our objective was to: estimate the hydrocarbon contamination extent in a contaminated site in northern France, and to adverse the effects of the oil spill on the groundwater properties. We aim to find a good combination of non-intrusive and low cost methods which we can use to follow the bio-remediation process, which is planned to proceed next year. We used four geophysical methods including electrical resistivity tomography, IP, GPR, and SP. The geophysical data was compared to geochemical ones obtained from 30 boreholes installed in the site during the geophysical surveys. Our results have shown: low electrical resistivity values; high chargeability values; negative SP anomalies; and attenuated GPR reflections coincident with groundwater contamination. Laboratory and field geochemical measurements have demonstrated increased groundwater electrical conductivity and increased microbial activity associated with hydrocarbon contamination of groundwater. Our study results support the conductive model suggested by studies such as Sauck (2000) and Atekwana et al., (2004), who suggest that biological alterations of hydrocarbon contamination can substantially modify the chemical and physical properties of the subsurface, producing a dramatic shift in the geo-electrical signature from resistive to conductive. The next stage of the research will include time lapse borehole

RCT: 2.05 Contamination Control, Course #8770

Energy Technology Data Exchange (ETDEWEB)

Hillmer, Kurt T. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-05-23

This report focuses on the detection and control of radioactive contamination, which are an integral part of an aggressive ALARA program and provide an indication of the effectiveness of engineering controls and proper work practices in preventing the release of radioactive material. Radioactive contamination, if undetected or not properly controlled, can be spread and contaminate areas, equipment, personnel, and the environment.

Evaluation of contaminated groundwater cleanup objectives

International Nuclear Information System (INIS)

Arquiett, C.; Gerke, M.; Datskou, I.

1996-01-01

The US Department of Energy's (DOE's) Environmental Restoration Program will be responsible for remediating the approximately 230 contaminated groundwater sites across the DOE Complex. A major concern for remediation is choosing the appropriate cleanup objective. The cleanup objective chosen will influence the risk to the nearby public during and after remediation; risk to remedial and non-involved workers during remediation; and the cost of remediation. This paper discusses the trends shown in analyses currently being performed at Oak Ridge National Laboratories' (ORNL's) Center for Risk Management (CRM). To evaluate these trends, CRM is developing a database of contaminated sites. This paper examines several contaminated groundwater sites selected for assessment from CRM's data base. The sites in this sample represent potential types of contaminated groundwater sites commonly found at an installation within DOE. The baseline risk from these sites to various receptors is presented. Residual risk and risk during remediation is reported for different cleanup objectives. The cost associated with remediating to each of these objectives is also estimated for each of the representative sites. Finally, the general trends of impacts as a function of cleanup objective will be summarized. The sites examined include the Savannah River site, where there was substantial ground pollution from radionuclides, oil, coal stockpiles, and other forms of groundwater contamination. The effects of various types of groundwater contamination on various types of future user is described. 4 refs., 3 figs., 2 tabs

Basic radiological studies contamination control experiments

International Nuclear Information System (INIS)

Duce, S.W.; Winberg, M.R.; Freeman, A.L.

1989-09-01

This report describes the results of experiments relating to contamination control performed in support of the Environmental Restoration Programs Retrieval Project. During the years 1950 to 1970 waste contaminated with plutonium and other transuranic radionuclides was disposed of in shallow land-filled pits and trenches at the Idaho National Engineering Laboratory. Due to potential for migration of radionuclides to an existing aquifer the feasibility of retrieving and repackaging the waste for placement in a final repository is being examined as part of a retrieval project. Contamination control experiments were conducted to determine expected respirable and nonrespirable plutonium contaminated dust fractions and the effectiveness of various dust suppression techniques. Three soil types were tested to determine respirable fractions: Rocky Flats Plant generic soil, Radioactive Waste Management Complex generic soil, and a 1:1 blend of the two soil types. Overall, the average respirable fraction of airborne dust was 5.4% by weight. Three contamination control techniques were studied: soil fixative sprays, misting agents, and dust suppression agents. All of the tested agents proved to be effective in reducing dust in the air. Details of product performance and recommended usage are discussed

DOE's plan for buried transuranic (TRU) contaminated waste

International Nuclear Information System (INIS)

Mathur, J.; D'Ambrosia, J.; Sease, J.

1987-01-01

Prior to 1970, TRU-contaminated waste was buried as low-level radioactive waste. In the Defense Waste Management Plan issued in 1983, the plan for this buried TRU-contaminated waste was to monitor the buried waste, take remedial actions, and to periodically evaluate the safety of the waste. In March 1986, the General Accounting Office (GAO) recommended that the Department of Energy (DOE) provide specific plans and cost estimates related to buried TRU-contaminated waste. This plan is in direct response to the GAO request. Buried TRU-contaminated waste and TRU-contaminated soil are located in numerous inactive disposal units at five DOE sites. The total volume of this material is estimated to be about 300,000 to 500,000 m 3 . The DOE plan for TRU-contaminated buried waste and TRU-contaminated soil is to characterize the disposal units; assess the potential impacts from the waste on workers, the surrounding population, and the environment; evaluate the need for remedial actions; assess the remedial action alternatives; and implement and verify the remedial actions as appropriate. Cost estimates for remedial actions for the buried TRU-contaminated waste are highly uncertain, but they range from several hundred million to the order of $10 billion

Contaminated metallic melt volume reduction testing

International Nuclear Information System (INIS)

Deichman, J.L.

1981-01-01

Laboratory scale metallic melts (stainless steel) were accomplished in support of Decontamination and Decommissioning's (D and D) contaminated equipment volume reduction and Low-Level Lead Site Waste programs. Six laboratory scale melts made with contaminated stainless steel provided data that radionuclide distribution can be predicted when proper temperature rates and ranges are employed, and that major decontamination occurs with the use of designed slagging materials. Stainless steel bars were contaminated with plutonium, cobalt, cesium and europium. This study was limited to stainless steel, however, further study is desirable to establish data for other metals and alloys. This study represents a positive beginning in defining the feasibility of economical volume reduction or conversion from TRU waste forms to LLW forms for a large portion of approximately 50 thousand tons of contaminated metal waste now being stored at Hanford underground or in deactivated facilities

Nickel contaminated titanium weld wire study

International Nuclear Information System (INIS)

Coffin, G.R.; Sumstine, R.L.

1979-01-01

Attachment of thermocouples to fuel rod welding problems at Exxon Nuclear Company and INEL prompted an investigation study of the titanium filler wire material. It was found that the titanium filler wire was contaminated with nickel which was jacketed on the wire prior to the drawing process at the manufacturers. A method was developed to 100% inspect all filler wire for future welding application. This method not only indicates the presence of nickel contamination but indicates quantity of contamination. The process is capable of high speed inspection necessary for various high speed manufacturing processes

Sequential extraction of uranium metal contamination

International Nuclear Information System (INIS)

Murry, M.M.; Spitz, H.B.; Connick, W.B.

2016-01-01

Samples of uranium contaminated dirt collected from the dirt floor of an abandoned metal rolling mill were analyzed for uranium using a sequential extraction protocol involving a series of five increasingly aggressive solvents. The quantity of uranium extracted from the contaminated dirt by each reagent can aid in predicting the fate and transport of the uranium contamination in the environment. Uranium was separated from each fraction using anion exchange, electrodeposition and analyzed by alpha spectroscopy analysis. Results demonstrate that approximately 77 % of the uranium was extracted using NH 4 Ac in 25 % acetic acid. (author)

Geohelminth contamination of fruits and vegetables cultivated on ...

African Journals Online (AJOL)

) was the most contaminated 65 (41.1%) and the least was Solanum macrocarpon (garden egg) 4 (2.5%). The samples were to some extent contaminated with either helminth ova, larvae or both, with the vegetables being more contaminated ...

Processing Contaminants in Food Production

DEFF Research Database (Denmark)

Granby, Kit; Duedahl-Olesen, Lene; Fromberg, Arvid

Contaminants like acrylamide, furan or PAHs (polyaromatic hydrocarbons) as e.g. Benz(a)pyrene may be formed during food processing. All of the substances are genotoxic carcinogens, and for that reason mitigation strategies to reduce the levels are needed. Examples of the formation of the processing...... contaminants and factors that influence the occurrence are given as well as suggestions for mitigation....

Processing Contaminants in Food Production

OpenAIRE

Granby, Kit; Duedahl-Olesen, Lene; Fromberg, Arvid; Pedreschi, Franco

2011-01-01

Contaminants like acrylamide, furan or PAHs (polyaromatic hydrocarbons) as e.g. Benz(a)pyrene may be formed during food processing. All of the substances are genotoxic carcinogens, and for that reason mitigation strategies to reduce the levels are needed. Examples of the formation of the processing contaminants and factors that influence the occurrence are given as well as suggestions for mitigation.

Investigating hydrocarbon contamination using ground penetrating radar

International Nuclear Information System (INIS)

Roest, P.B. van der; Brasser, D.J.S.; Wagebaert, A.P.J.; Stam, P.H.

1996-01-01

The increasing costs of remediating contaminated sites has stimulated research for cost reducing techniques in soil investigation and clean-up techniques. Under the traditional approach soil borings and groundwater wells are used to investigate contaminated soil. These are useful tools to determine the amount and characteristics of the contamination, but they are inefficient and costly in providing information on the location and extent of contamination as they only give information on one point. This often leads to uncertainty in estimating clean-up costs or, even worse, to unsuccessful clean-ups. MAP Environmental Research has developed a technology using Ground Penetrating Radar (GPR) in combination with in-house developed software to locate and define the extent of hydrocarbon contamination. With this technology, the quality of site investigation is increased while costs are reduced. Since 1994 MAP has been improving its technology and has applied it to over 100 projects, which all have been checked afterwards by conventional drilling. This paper gives some general characteristics of the method and presents a case study. The emphasis of this paper lies on the practical application of GPR to hydrocarbon contamination detection

Quebec's new contaminated sites policy : special report

International Nuclear Information System (INIS)

Anon.

1998-01-01

Quebec's new contaminated site policy sets out a broad new set of requirements with which industry will have to comply. The new policy entitled 'Politique de protection des sols et de rehabilitation des terrains contamines' is much more comprehensive and detailed than its 1988 predecessor and contains many new elements. The policy seeks to maintain soil and groundwater quality criteria and focuses on the protection of clean commercial and industrial sites through pollution prevention actions. It also takes into account progress which has been made since the inventory of contaminated sites across Quebec. It considers the characteristics of each site and the problems posed by ongoing disposal of contaminated soils in landfills and advances in treatment technologies. The issue of who is responsible for contaminated sites is addressed and the requirements for responsible parties are described in detail. Risk assessment was also introduced as a tool for remediation planning in some cases. The new policy stresses prevention, and attempts to clearly outline site characterization and remediation duties for new and existing industries that pose potential risk of soil and groundwater contamination. 2 tabs., 2 figs

Monitoring and evaluation techniques for airborne contamination

Energy Technology Data Exchange (ETDEWEB)

Yihua, Xia [China Inst. of Atomic Energy, Beijing (China)

1997-06-01

Monitoring and evaluation of airborne contamination are of great importance for the purpose of protection of health and safety of workers in nuclear installations. Because airborne contamination is one of the key sources to cause exposure to individuals by inhalation and digestion, and to cause diffusion of contaminants in the environment. The main objectives of monitoring and evaluation of airborne contamination are: to detect promptly a loss of control of airborne material, to help identify those individuals and predict exposure levels, to assess the intake and dose commitment to the individuals, and to provide sufficient documentation of airborne radioactivity. From the viewpoint of radiation protection, the radioactive contaminants in air can be classified into the following types: airborne aerosol, gas and noble gas, and volatile gas. In this paper, the following items are described: sampling methods and techniques, measurement and evaluation, and particle size analysis. (G.K.)

Monitoring and evaluation techniques for airborne contamination

International Nuclear Information System (INIS)

Xia Yihua

1997-01-01

Monitoring and evaluation of airborne contamination are of great importance for the purpose of protection of health and safety of workers in nuclear installations. Because airborne contamination is one of the key sources to cause exposure to individuals by inhalation and digestion, and to cause diffusion of contaminants in the environment. The main objectives of monitoring and evaluation of airborne contamination are: to detect promptly a loss of control of airborne material, to help identify those individuals and predict exposure levels, to assess the intake and dose commitment to the individuals, and to provide sufficient documentation of airborne radioactivity. From the viewpoint of radiation protection, the radioactive contaminants in air can be classified into the following types: airborne aerosol, gas and noble gas, and volatile gas. In this paper, the following items are described: sampling methods and techniques, measurement and evaluation, and particle size analysis. (G.K.)

Phyto-remediation of contaminated soils

International Nuclear Information System (INIS)

Chagvardieff, P.

2014-01-01

Some plants can be selected for their capacity to extract radionuclides from the soil, on the contrary other plants can be chosen for being able to produce food grade products in a contaminated environment. Modern genetic methods can be used to enhance these abilities and turn some plants into an efficient means in the managing of contaminated areas. The DEMETERRES project that gathers different research organisations like CEA, IRSN and INRA and industrial partners like AREVA and VEOLIA aims at developing innovative bio-technologies like phyto-extraction and environment friendly physico-chemical technologies for the remediation of contaminated soils. This project was launched in 2013 on a 5-year scheme and is expected to lead to industrial applications. (A.C.)

Nuclear explosion and internal contamination

International Nuclear Information System (INIS)

Aeberhardt, A.

1956-01-01

By the study of the conditions of internal contamination due to the radioactive mixture produced by a nuclear explosion, the parts played by the relative weights of the different elements and the mode of expression of the doses are considered. Only the knowledge of the weight composition of the contamination mixture and of its evolution as a function of time can provide the required basis for the study of its metabolism in the organism. The curves which give the composition of the fission product mixture - in number of nuclei - - as a function of time - have been established. These curves are applied to some practical examples, particularly relative to the nature of contamination, radiotoxicity of some elements and assessment of hazards. (author) [fr

Shuttle on-orbit contamination and environmental effects

Science.gov (United States)

Leger, L. J.; Jacobs, S.; Ehlers, H. K. F.; Miller, E.

1985-01-01

Ensuring the compatibility of the space shuttle system with payloads and payload measurements is discussed. An extensive set of quantitative requirements and goals was developed and implemented by the space shuttle program management. The performance of the Shuttle system as measured by these requirements and goals was assessed partly through the use of the induced environment contamination monitor on Shuttle flights 2, 3, and 4. Contamination levels are low and generally within the requirements and goals established. Additional data from near-term payloads and already planned contamination measurements will complete the environment definition and allow for the development of contamination avoidance procedures as necessary for any payload.

Optimization of monitoring sewage with radionuclide contaminants

International Nuclear Information System (INIS)

Egorov, V.N.

1991-01-01

Recommendations on optimization of monitoring contaminated sewage aimed at enviromental protection agxinst radioactive contamination at minimum cost are presented. The way of selecting water sampling technique depends on water composition stability and flow rate. Depending on the type of radionuclide distribution in the sewage one can estimate minimum frequency of sampling or number of samples sufficient for assuring reliability of the conclusion on the excess or non-excess of permissible radioactive contamination levels, as well as analysis assigned accuracy. By irregular contaminated sewage-discharge and possibility of short-term releases of different form and duration, sampling should be accomplished through automatic devices of continuons or periodic operation

Contaminant classification using cosine distances based on multiple conventional sensors.

Science.gov (United States)

Liu, Shuming; Che, Han; Smith, Kate; Chang, Tian

2015-02-01

Emergent contamination events have a significant impact on water systems. After contamination detection, it is important to classify the type of contaminant quickly to provide support for remediation attempts. Conventional methods generally either rely on laboratory-based analysis, which requires a long analysis time, or on multivariable-based geometry analysis and sequence analysis, which is prone to being affected by the contaminant concentration. This paper proposes a new contaminant classification method, which discriminates contaminants in a real time manner independent of the contaminant concentration. The proposed method quantifies the similarities or dissimilarities between sensors' responses to different types of contaminants. The performance of the proposed method was evaluated using data from contaminant injection experiments in a laboratory and compared with a Euclidean distance-based method. The robustness of the proposed method was evaluated using an uncertainty analysis. The results show that the proposed method performed better in identifying the type of contaminant than the Euclidean distance based method and that it could classify the type of contaminant in minutes without significantly compromising the correct classification rate (CCR).

Contaminated Mexican steel incident

International Nuclear Information System (INIS)

1985-01-01

This report documents the circumstances contributing to the inadvertent melting of cobalt 60 (Co-60) contaminated scrap metal in two Mexican steel foundries and the subsequent distribution of contaminated steel products into the United States. The report addresses mainly those actions taken by US Federal and state agencies to protect the US population from radiation risks associated with the incident. Mexico had much more serious radiation exposure and contamination problems to manage. The United States Government maintained a standing offer to provide technical and medical assistance to the Mexican Government. The report covers the tracing of the source to its origin, response actions to recover radioactive steel in the United States, and return of the contaminated materials to Mexico. The incident resulted in significant radiation exposures within Mexico, but no known significant exposure within the United States. Response to the incident required the combined efforts of the Nuclear Regulatory Commission (NRC), Department of Energy, Department of Transportation, Department of State, and US Customs Service (Department of Treasury) personnel at the Federal level and representatives of all 50 State Radiation Control Programs and, in some instances, local and county government personnel. The response also required a diplomatic interface with the Mexican Government and cooperation of numerous commercial establishments and members of the general public. The report describes the factual information associated with the event and may serve as information for subsequent recommendations and actions by the NRC. 8 figures

Chemical oxidation of cable insulating oil contaminated soil

NARCIS (Netherlands)

Jinlan Xu,; Pancras, T.; Grotenhuis, J.T.C.

2011-01-01

Leaking cable insulating oil is a common source of soil contamination of high-voltage underground electricity cables in many European countries. In situ remediation of these contaminations is very difficult, due to the nature of the contamination and the high concentrations present. Chemical

Technical options for the remediation of contaminated groundwater

Energy Technology Data Exchange (ETDEWEB)

1999-06-01

This report provides a description of the nature and extent of problems related to radioactive groundwater contamination by outlining the environmental impacts, the sources of contamination and the contaminants of concern radionuclides and their associated contaminants - the main exposure pathways and transport processes and the assessment of risks associated with contaminated groundwater. The main emphasis of this report is on methodologies used in groundwater remediation and available technologies. The methodology section outlines the importance of an initial scoping analysis including the evaluation of uncertainties of the available data and the necessity for defining clear objectives for data collection. This is then followed by comprehensive site characterization, setting of goals and developing alternatives which will be analysed in detail. Available technologies are grouped generally into in situ methods aiming at a containment of the contaminants in place and engineered treatment methods involving an alteration of groundwater flow, quantity and/or quality to achieve compliance with set goals. Groundwater remediation by natural flushing allows the natural groundwater movement and geochemical processes to decrease the contaminant concentrations to acceptable levels over a specified period of time. This method is increasingly accepted in areas where the use of groundwater can be temporarily restricted or engineered cleanup methods do not offer particular advantage over the natural processes. The application of technological methods for remediating contaminated groundwaters has to be considered in conjunction with management options such as diversion and development of alternative water sources. The experience with groundwater contamination accrued in IAEA Member States is concentrated in those countries with active uranium mining and milling facilities and nuclear energy programmes. This experience is reported in the Annexes, which include case studies. It

Technical options for the remediation of contaminated groundwater

International Nuclear Information System (INIS)

1999-06-01

This report provides a description of the nature and extent of problems related to radioactive groundwater contamination by outlining the environmental impacts, the sources of contamination and the contaminants of concern radionuclides and their associated contaminants - the main exposure pathways and transport processes and the assessment of risks associated with contaminated groundwater. The main emphasis of this report is on methodologies used in groundwater remediation and available technologies. The methodology section outlines the importance of an initial scoping analysis including the evaluation of uncertainties of the available data and the necessity for defining clear objectives for data collection. This is then followed by comprehensive site characterization, setting of goals and developing alternatives which will be analysed in detail. Available technologies are grouped generally into in situ methods aiming at a containment of the contaminants in place and engineered treatment methods involving an alteration of groundwater flow, quantity and/or quality to achieve compliance with set goals. Groundwater remediation by natural flushing allows the natural groundwater movement and geochemical processes to decrease the contaminant concentrations to acceptable levels over a specified period of time. This method is increasingly accepted in areas where the use of groundwater can be temporarily restricted or engineered cleanup methods do not offer particular advantage over the natural processes. The application of technological methods for remediating contaminated groundwaters has to be considered in conjunction with management options such as diversion and development of alternative water sources. The experience with groundwater contamination accrued in IAEA Member States is concentrated in those countries with active uranium mining and milling facilities and nuclear energy programmes. This experience is reported in the Annexes, which include case studies. It

The contamination on farm products from 125I

International Nuclear Information System (INIS)

Zhao Wenhu; Xu Shiming; Hou Lanxin

1990-02-01

The 125 I contamination on 15 farm products have been investigated. The effects of 12 farm crops (wheat, bean, eggplants and other vegetables) contaminated by 125 I during the growing stage on their fruits and seeds have been studied. The results show that the 125 I radioactive substance is mainly concentrated on the fruit surface, and the radioactivity rapidly decreased towards its kernel. The fruits and seeds would not be contaminated when plants were contaminated in the seedling stage

Contaminant resorption during soil washing

International Nuclear Information System (INIS)

Gombert, D.

1993-01-01

To evaluate the applicability of soil washing to a specific site requires some basic research in how contaminants are bound. Much can be learned from sequential extraction methodology based on micronutrient bioavailability studies wherein the soil matrix is chemically dissected to selectively remove particular fixation mechanisms independently. This procedure uses a series of progressively more aggressive solvents to dissolve the principle phases that make up a soil, however, the published studies do not appear to consider the potential for a contaminant released from one type of site to resorb on another site during an extraction. This physical model assumes no ion exchange or adsorption at sites either previously occupied by other ions, or exposed by the dissolution. Therefore, to make engineering use of the sequential extraction data, the release of contamination must be evaluated relative to the effects of resorption. Time release studies were conducted to determine the optimum duration for extraction to maximize complete destruction of the target matrix fraction while minimizing contaminant resorption. Tests with and without a potassium brine present to inhibit cesium resorption indicated extraction efficiency could be enhanced by as much as a factor of ten using the brine

Melting of contaminated metallic waste

International Nuclear Information System (INIS)

Lee, Y.-S.; Cheng, S.-Y.; Kung, H.-T.; Lin, L.-F.

2004-01-01

Approximately 100 tons of contaminated metallic wastes were produced each year due to maintenance for each TPC's nuclear power reactor and it was roughly estimated that there will be 10,000 tons of metallic scraps resulted from decommissioning of each reactor in the future. One means of handling the contaminated metal is to melt it. Melting process owns not only volume reduction which saves the high cost of final disposal but also resource conservation and recycling benefits. Melting contaminated copper and aluminum scraps in the laboratory scale have been conducted at INER. A total of 546 kg copper condenser tubes with a specific activity of about 2.7 Bq/g was melted in a vacuum induction melting facility. Three types of products, ingot, slag and dust were derived from the melting process, with average activities of 0.10 Bq/g, 2.33 Bq/g and 84.3 Bq/g respectively. After the laboratory melting stage, a pilot plant with a 500 kg induction furnace is being designed to melt the increasingly produced contaminated metallic scraps from nuclear facilities and to investigate the behavior of different radionuclides during melting. (author)

Analysis of East Tank Farms Contamination Survey Frequency

International Nuclear Information System (INIS)

ELDER, R.E.

2000-01-01

This document provides the justification for the change in survey frequency in East Tank Farms occupied contamination areas from weekly to monthly. The Tank Farms Radiological Control Organization has performed radiological surveys of its Contamination Area (CA) Double Shell Tank (DST) farms in 200 East Area on a weekly basis for several years. The task package (DST-W012) controlling these routines designates specific components, at a minimum, that must be surveyed whenever the task is performed. This document documents the evaluation of these survey requirements and provides the recommendation and basis for moving DST tank farms in the 200 East Area from a weekly to monthly contamination survey. The contamination surveys for occupied contamination areas in West Tank Farms (WTF) were changed from a weekly frequency to a monthly frequency in 1997. Review of contamination survey data in WTF indicates a monthly interval remains satisfactory

On the intrinsic gettering in Cu-contaminated Cz-Si

International Nuclear Information System (INIS)

Schmalz, K.; Kirscht, F.G.; Babanskaja, I.; Kittler, M.; Richter, H.; Seifert, W.

1985-01-01

NAA, TEM, DLTS, and EBIC investigations of Cu-contaminated Cz-Si with an intrinsic-gettering procedure realized by a multistep heat treatment demonstrate the efficiency of intrinsic gettering concerning redistribution to volume defects for Cu-contamination up to 10 16 cm -3 . The Cu-precipitation at the surface can still be suppressed for such contamination due to volume defects. However, in this case the concentration of contamination induced deep level centers at the surface is independent of the volume defect density. Only for Cu-contamination of about 10 15 cm -3 the gettering effect is strong enough to prevent the introduction of contamination induced deep levels at the surface. (author)

Economics and risks of recycling radioactively contaminated concrete

International Nuclear Information System (INIS)

Parker, F.L.; Ayers, K.W.

1997-01-01

As Decontamination and Decommissioning activities proceed within the DOE complex, tremendous volumes of both radioactively contaminated and non-contaminated concrete will be processed for disposal. Current practice is to decontaminate the concrete, dispose of the contamination at LLW facilities and ship the concrete rubble to C ampersand D landfills for disposal. This study evaluates the economic, health and safety, legal, and social aspects of recycling radioactively contaminated concrete. Probabilistic models were used to estimate costs and risks. The model indicates that the radioactively contaminated concrete can be recycled at the same or lower cost than current or alternative practices. The risks associated with recycling were consistently less than or equal to the other alternatives considered

The supposed radioactive contamination of the Puelche aquifer

International Nuclear Information System (INIS)

Martini, Leopoldo E.

2005-01-01

The paper attempts to clarify the supposed radioactive contamination of the Puelche Aquifer in the Ezeiza Atomic Center Area, Ezeiza, province of Buenos Aires (Argentina). Reports are listed that show categorically that no anthropogenic uranium contamination is present. As far as the nitrates contamination is concerned, it is not generated by the Ezeiza Atomic Center, because the Center is downward from the contaminated zone. It is possible that the contamination is produced by houses in the area without suitable sewage. In the present case the best contribution to the environmental right, besides the adaptation and the systematization of the different legal instruments, is to found the analysis of the facts on the scientific and technical knowledge. (author) [es

Proposal for derivation of limit values for skin contamination

International Nuclear Information System (INIS)

Schieferdecker, H.; Koelzer, W.; Henrichs, K.

1985-04-01

From the primary limit value for the skin dose secondary limit values are derived for skin contamination which can be used in practical radiation protection work. In analogy to the secondary limit value for the maximum permissible body burden in case of incorporation, limit values for the 'maximum permissible skin burden' are calculated with the help of dose factors for application in case of skin contamination. They can be derived from the skin dose limit values. Considering that the skin is exposed to contamination but temporarily, in analogy to the annual limit on intake in case of incorporation a 'limit value of skin contamination' is derived for immediately removable contaminations and for one day of exposure, whereas with respect to non-removable contamination and taking into account the renewal of the skin, a limit value of annual skin contamination is defined for non-removable skin contaminations. An investigation level for skin contamination is assumed as a threshold above which defined measures must be taken. Regarding these measures not more than three times appropriate washing is recommended with the subsequent procedure determined by the level of residual contamination. The respective limit values are indicated for some radionuclides selected as examples (C-14, Co-60, Sr-90, Y-90, I-131, Cs-137, Ce-141, Pu-239). (orig./HP) [de

Analysis of bacterial strains from contaminated and non ...

African Journals Online (AJOL)

Administrator

2007-05-02

May 2, 2007 ... A total 18 strains were collected from non-contaminated and contaminated environments, and were purified. All purified strains were characterized for Gram reaction and biochemical analysis. Screening for bioplastic production was done by Sudan black staining. Strains isolated from non-contaminated.

Associated microbial contaminants in in-vitro micropropagation of ...

African Journals Online (AJOL)

Studies were carried out to determine the microbial contaminants associated with in-vitro micropropagation of Ipomea batatas (sweet potato). The contaminants were found to be mostly fungal organisms, Aspergillus Spp (62%), Penicillum Spp. (31%), Fusarium Spp. (5%) and Alternaria Spp. (2%). Bacterial contamination ...

ARSENIC CONTAMINATION IN GROUNDWATER: A STATISTICAL MODELING

Directory of Open Access Journals (Sweden)

Palas Roy

2013-01-01

Full Text Available High arsenic in natural groundwater in most of the tubewells of the Purbasthali- Block II area of Burdwan district (W.B, India has recently been focused as a serious environmental concern. This paper is intending to illustrate the statistical modeling of the arsenic contaminated groundwater to identify the interrelation of that arsenic contain with other participating groundwater parameters so that the arsenic contamination level can easily be predicted by analyzing only such parameters. Multivariate data analysis was done with the collected groundwater samples from the 132 tubewells of this contaminated region shows that three variable parameters are significantly related with the arsenic. Based on these relationships, a multiple linear regression model has been developed that estimated the arsenic contamination by measuring such three predictor parameters of the groundwater variables in the contaminated aquifer. This model could also be a suggestive tool while designing the arsenic removal scheme for any affected groundwater.

Modeling contaminant plumes in fractured limestone aquifers

DEFF Research Database (Denmark)

Mosthaf, Klaus; Brauns, Bentje; Fjordbøge, Annika Sidelmann

Determining the fate and transport of contaminant plumes from contaminated sites in limestone aquifers is important because they are a major drinking water resource. This is challenging because they are often heavily fractured and contain chert layers and nodules, resulting in a complex transport...... model. The paper concludes with recommendations on how to identify and employ suitable models to advance the conceptual understanding and as decision support tools for risk assessment and the planning of remedial actions....... behavior. Improved conceptual models are needed for this type of site. Here conceptual models are developed by combining numerical models with field data. Several types of fracture flow and transport models are available for the modeling of contaminant transport in fractured media. These include...... the established approaches of the equivalent porous medium, discrete fracture and dual continuum models. However, these modeling concepts are not well tested for contaminant plume migration in limestone geologies. Our goal was to develop and evaluate approaches for modeling the transport of dissolved contaminant...

Human Forward Contamination Strategic Plan

Science.gov (United States)

Rucker, Michelle

2015-01-01

When we send humans to search for life on Mars, we'll need to know what we brought with us versus what may already be there. Unlike the Mars rovers that we cleaned once and sent on their way, humans will provide a constantly regenerating contaminant source. Are we prepared to certify that we can meet forward contamination protocols as we search for life at new destinations?

Measurement of contamination by 241Am

International Nuclear Information System (INIS)

Hemmingsen, L.B.S.

1991-08-01

In relation to the fact that four employees at the Danish Isotope Center who had regularly cleaned the smoke detectors used for control measurements were found to be contaminated with 241 Am, the aim was to investigate the suitability of the Phoswich detector system for measurement of contamination of humans by 241 Am. It was also wished to compare this measuring method with other selected ones. The measurement results are presented in detail. It was found that measurements taken on the cranium with the Phoswich detectors were more suitable for measurement of contamination by 241 Am than the use of a Ge detector on the liver, - because of the first-named method's greater degree of measuring efficiency, (0.013 cps/Bq compared with 0.0001 cps/Bq in the case of Ge detector measurement) and lower minimum detectable activity in relation to that activity that was measured on A1 (one of the employees). It was found that Phoswich-detector measurement and measuring of urine samples supplemented each other in a satisfactory way. The Phoswich detector enables a quick measurement of the degree of seriousness of the contamination of a person and a relatively accurate determination of the calculated intake of contamination which has a size of at least twice the annual limit of intake size. Measurements of urine samples enable smaller amounts of contamination to be revealed, but this takes ca. 32 weeks and is less accurate than Phoswich measurement especially if a long time has elapsed after the intake. (AB) (34 refs.)

Microbial contamination level profiles attributed to contamination of beef carcasses, personnel, and equipment: case of small and medium enterprise slaughterhouses

DEFF Research Database (Denmark)

Wambui, Joseph; Lamuka, Peter; Karuri, Edward

2018-01-01

The microbial contamination level profiles (MCLPs) attributed to contamination of beef carcasses, personnel, and equipment in five Kenyan small and medium enterprise slaughterhouses were determined. Aerobic plate counts, Enterobacteriaceae, Staphylococcus, and Salmonella were used to determine...... contamination at four different slaughter stages, namely, dehiding, evisceration, splitting, and dispatch. Microbiological criteria of the four microorganisms were used to score contamination levels (CLs) as poor (0), poor to average (1), average (2), or good (3). MCLPs were further assigned to carcasses......, personnel, and equipment at each stage by summing up the CL scores. The CL score attributed to aerobic plate count contamination was 2 or 3 for carcasses but 0 for personnel and equipment in almost all slaughterhouses. A score of 0 on carcasses was mostly attributed to Enterobacteriaceae at evisceration...

The use of sparge curtains for contaminant plume control

International Nuclear Information System (INIS)

Molnaa, B.; Dablow, J.

1994-01-01

Contamination by petroleum hydrocarbons and organic solvents represents a major impact to soil and groundwater. Following recent research and development, several technologies have evolved to treat saturated zone adsorbed- and dissolved-phase contaminants in situ. These technologies include bioremediation and air sparging. Funnel and gate approaches have been developed at the Waterloo Center for Groundwater Research to control contaminant plume migration and treat dissolved-phase contaminants before allowing migration downgradient and off site. The process consists of using low hydraulic conductivity cutoff walls to funnel groundwater flow through gates that contain in situ bioreactors. These systems can maintain hydraulic control and treat dissolved-phase contaminants at the downgradient margins of plumes, while minimizing, or in some cases eliminating, the need for groundwater pumping. Sparge curtains can be applied to treat dissolved-phase contaminants and prevent downgradient, off-site migration of contaminated groundwater

Self-restoration of contaminated territories

International Nuclear Information System (INIS)

Arapis, G.; Sobotovich, E.; Bondarenko, G.; Sadolko, I.; Petrayev, E.; Sokolik, G.

1996-01-01

This paper illustrates the experience gained in the field of natural restoration of contaminated vast ecosystems. Prior to recommending a large-scale application of any rehabilitation technique, it is important to know the medium-and long- term intensity of self-restoration for most of the affected territories. Three main ways express the process of self-restoration: the natural radioactive decay, the transfer of radionuclides out of natural ecosystems and the ability of some pedological components to fixate the contaminants. The first way is a real decontamination process resulting in the removal from the biosphere of significant quantities of radionuclides. Indeed, during the last years the total activity of short-life-isotopes was decreased by a factor of some thousand and actually, the main contaminants are 137 Cs and 90 Sr which are decreasing according to their half-life. The two other ways of self-restoration are closely connected with radionuclides migration (vertical or/and horizontal) in soils. The vertical migration velocities of 137 Cs and 90 St in typical soils of contaminated regions in Ukraine and Belarus were evaluated annually during 9 years since the accident. In most of these soils the migration rate of 90 Sr seems higher than this of 137 Cs and ranges from 0.71 to 1.54 cm/year and 0.10 to 1.16 cm/year respectively. At present time the main part of radionuclides is located in the upper 10 cm layer of soils. The ability of soils components to immobilize the radionuclides was also investigated. From 1989 to 1994 approximately 57% of 137 Cs was converted in fixed forms and for the year 2000 it is expected that this percentage will be 80%. Finally, for total contaminated regions, the obtained results on vertical migration velocity of radionuclides as a function of the soil type, are presented under the form of a map in order to help decision makers to determine the feasibility and the methodology for restoration of areas contaminated by 137 Cs and 90

An overview of the bioremediation of inorganic contaminants

International Nuclear Information System (INIS)

Bolton, H. Jr.; Gorby, Y.A.

1995-01-01

Bioremediation, or the biological treatment of wastes, usually is associated with the remediation of organic contaminants. Similarly, there is an increasing body of literature and expertise in applying biological systems to assist in the bioremediation of soils, sediments, and water contaminated with inorganic compounds including metals, radionuclides, nitrates, and cyanides. Inorganic compounds can be toxic both to humans and to organisms used to remediate these contaminants. However, in contrast to organic contaminants, most inorganic contaminants cannot be degraded, but must be remediated by altering their transport properties. Immobilization, mobilization, or transformation of inorganic contaminants via bioaccumulation, biosorption, oxidation, reduction, methylation, demethylation, metal-organic complexation, ligand degradation, and phytoremediation are the various processes applied in the bioremediation of inorganic compounds. This paper briefly describes these processes, referring to other contributors in this book as examples when possible, and summarize the factors that must be considered when choosing bioremediation as a cleanup technology for inorganics. Understanding the current state of knowledge as well as the limitations for bioremediation of inorganic compounds will assist in identifying and implementing successful remediation strategies at sites containing inorganic contaminants. 79 refs

Criteria for the designation of radioactively contaminated land

International Nuclear Information System (INIS)

Titley, J.; Mobbs, S.; Burgess, P.; Hitchins, G.; Sinclair, P.

1999-01-01

This report examines the criteria for the designation of radioactively contaminated land. It should be read in conjunction with reference to another output from the project i.e. Environment Agency report, Technical Support Material for the Regulation of Radioactively Contaminated Land 1999. This report deals with the intervention on radioactively contaminated sites i.e. where no change of land use is anticipated and where the land has become contaminated as a result of previous land use and not current practices. (author)

Surfactant screening of diesel-contaminated soil

International Nuclear Information System (INIS)

Peters, R.W.; Montemagno, C.D.; Shem, L.; Lewis, B.-A.

1992-01-01

At one installation in California, approximately 60,000 gal of No. 2 diesel fuel leaked into the subsurface environment, resulting in contamination at depths from 6 to 34 m below the surface. Argonne National Laboratory was contracted to perform treatability studies for site remediation. This paper summarizes a surfactant screening/surfactant flooding research program in which 22 surfactants were screened for their effectiveness in mobilizing the organics from the contaminated soil prior to bioremediation. Anionic surfactants resulted in the greatest degree of diesel mobilization. The most promising surfactants will be employed on contaminated soil samples obtained from the site

Mycoplasma contamination of Chlamydia pneumoniae isolates

DEFF Research Database (Denmark)

Huniche, BS; Jensen, Lise Torp; Birkelund, Svend

1998-01-01

media, immunoblotting, polymerase chain reaction and pulsed field gel electrophoresis. Two of the 6 ATCC isolates [ATCC VR1355 (TWAR strain 2043) and ATCC VR1356 (TWAR strain 2023)] were infected with Mycoplasma hominis and 1 isolate [ATCC VR2282 (TWAR strain TW183)] was contaminated with both...... Mycoplasma hominis and Mycoplasma orale, whereas 3 of the ATCC isolates [ATCC VR1310, ATCC VR1360 (TWAR strain CM-1) and ATCC 53592 (TWAR strain AR39)] were not contaminated. The Finnish C. pneumoniae isolates Kajaani 6 and Parola were found to be contaminated with M. hominis and M. orale, respectively...

Efficient reconstruction of contaminant release history

Energy Technology Data Exchange (ETDEWEB)

Alezander, Francis [Los Alamos National Laboratory; Anghel, Marian [Los Alamos National Laboratory; Gulbahce, Natali [NON LANL; Tartakovsky, Daniel [NON LANL

2009-01-01

We present a generalized hybrid Monte Carlo (GHMC) method for fast, statistically optimal reconstruction of release histories of reactive contaminants. The approach is applicable to large-scale, strongly nonlinear systems with parametric uncertainties and data corrupted by measurement errors. The use of discrete adjoint equations facilitates numerical implementation of GHMC, without putting any restrictions on the degree of nonlinearity of advection-dispersion-reaction equations that are used to described contaminant transport in the subsurface. To demonstrate the salient features of the proposed algorithm, we identify the spatial extent of a distributed source of contamination from concentration measurements of a reactive solute.

Occurrence of Surface Water Contaminations: An Overview

Science.gov (United States)

Shahabudin, M. M.; Musa, S.

2018-04-01

Water is a part of our life and needed by all organisms. As time goes by, the needs by human increased transforming water quality into bad conditions. Surface water contaminated in various ways which is pointed sources and non-pointed sources. Pointed sources means the source are distinguished from the source such from drains or factory but the non-pointed always occurred in mixed of elements of pollutants. This paper is reviewing the occurrence of the contaminations with effects that occurred around us. Pollutant factors from natural or anthropology factors such nutrients, pathogens, and chemical elements contributed to contaminations. Most of the effects from contaminated surface water contributed to the public health effects also to the environments.

9 CFR 113.28 - Detection of mycoplasma contamination.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Detection of mycoplasma contamination... REQUIREMENTS Standard Procedures § 113.28 Detection of mycoplasma contamination. The heart infusion test, using... for mycoplasma contamination is prescribed in an applicable Standard Requirement or in the filed...

Method for electrolytic decontamination of radioactive contaminated metals

International Nuclear Information System (INIS)

Tanaka, Akio; Horita, Masami; Onuma, Tsutomu; Kato, Koji

1991-01-01

The invention relates to an electrolytic decontamination method for radioactive contaminated metals. The contaminated sections are eluted by electrolysis after the surface of a piece of equipment used with radioactive substances has been immersed in an electrolyte. Metal contaminated by radioactive substances acts as the anode

The influence of hydrology on lacustrine sediment contaminant records

Science.gov (United States)

Rosen, Michael R.

2015-01-01

The way water flows to a lake, through streams, as runoff, or as groundwater, can control the distribution and mass of sediment and contaminants deposited. Whether a lake is large or small, deep or shallow, open or closed, the movement of water to a lake and the circulation patterns of water within a lake control how and where sediment and contaminants are deposited. Particle-associated contaminants may stay close to the input source of contamination or be transported by currents to bathymetric lows. A complex morphology of the lake bottom or shoreline can also affect how contaminants will be distributed. Dissolved contaminants may be widely dispersed in smaller lakes, but may be diluted in large lakes away from the source. Although dissolved contaminants may not be deposited in lake sediments, the impact of dissolved contaminants (such as nitrogen) may be reflected by the ecosystem. For instance, increased phosphorus and nitrogen may increase organic content or algal biomass, and contribute to eutrophication of the lake over time. Changes in oxidation-reduction potential at the sediment-water interface may either release some contaminants to the water column or conversely deposit other contaminants to the sediment depending on the compound’s chemical characteristics. Changes in land use generally affect the hydrology of the watershed surrounding a lake, providing more runoff if soil binding vegetation is removed or if more impervious cover (roads and buildings) is increased. Groundwater inputs may change if pumping of the aquifer connected to the lake occurs. Even if groundwater is only a small portion of the volume of water entering a lake, if contaminant concentrations in the aquifer are high compared to surface water inputs, the mass of contaminants from groundwater may be as, or more, important than surface water contributions.

Water contamination, land prices, and the statute of repose

Science.gov (United States)

John F. Chamblee; Carolyn A. Dehring; Craig A. Depken; Joseph R. Nicholson

2015-01-01

We examine how water contamination risk from an inactive hazardous waste site is capitalized into surrounding vacant land prices. After public knowledge of the first instance of off-site contamination, we find that shallow groundwater contamination potential is negatively capitalized into land prices, as is proximity to a known contaminated well. Public knowledge of...

Decrease of radioactive contamination by official wine-making procedures

International Nuclear Information System (INIS)

Foerstel, H.; Steffens, W.

1993-01-01

A contamination with strontium may be lowered by precipitation as tartaric acid complex, a contamination with cesium or cobalt by precipitation of hexacyanoferrates, both accepted wine-making techniques. Contaminated must was obtained both by addition of nuclides to products from the wine harvest or better by growing wine plants on contaminated soils. (orig.) [de

Groundwater arsenic contamination throughout China.

Science.gov (United States)

Rodríguez-Lado, Luis; Sun, Guifan; Berg, Michael; Zhang, Qiang; Xue, Hanbin; Zheng, Quanmei; Johnson, C Annette

2013-08-23

Arsenic-contaminated groundwater used for drinking in China is a health threat that was first recognized in the 1960s. However, because of the sheer size of the country, millions of groundwater wells remain to be tested in order to determine the magnitude of the problem. We developed a statistical risk model that classifies safe and unsafe areas with respect to geogenic arsenic contamination in China, using the threshold of 10 micrograms per liter, the World Health Organization guideline and current Chinese standard for drinking water. We estimate that 19.6 million people are at risk of being affected by the consumption of arsenic-contaminated groundwater. Although the results must be confirmed with additional field measurements, our risk model identifies numerous arsenic-affected areas and highlights the potential magnitude of this health threat in China.

Determination of the external contamination and cross-contamination by cytotoxic drugs on the surfaces of vials available on the Swiss market.

Science.gov (United States)

Fleury-Souverain, Sandrine; Nussbaumer, Susanne; Mattiuzzo, Marc; Bonnabry, Pascal

2014-04-01

The external contamination and cross-contamination by cytotoxic drugs on the surface (outside and septum) of 133 vials from various manufacturers and available on the Swiss market were evaluated. All of the tested vials contained one of the following active ingredients: cyclophosphamide, cytarabine, doxorubicin, epirubicin, etoposide phosphate, gemcitabine, ifosfamide, irinotecan, methotrexate or vincristine. The validated wiping liquid chromatography-mass spectrometry method used in this study allowed for the simultaneous determination of these 10 cytotoxic drugs in less than 30 min. External contamination by cytotoxic drugs was detected on 63% of tested vials (outside and septum). The highest contamination level was observed on etoposide phosphate vials with 1896.66 ng of active ingredient on the outside of the vial. Approximately 20% of the contaminated vials had greater than 10 ng of cytotoxic drugs. Chemical contamination on the septum was detected on 38% of the vials. No contamination or very low levels of cytotoxic drugs, less than 1 ng per vial, were detected on the vials protected by plastic shrink-wrap. Traces of cytotoxic drugs different from the active ingredient were detected on 35% of the tested vials. Handling cytotoxic vials with gloves and having a procedure for the decontamination of vials are of the utmost importance for reducing exposure to cytotoxic drugs. Moreover, manufacturers must improve their procedures to provide products free from any contamination.

Factors Affecting Microbial Contamination of Market Eggs: A Review

Directory of Open Access Journals (Sweden)

Svobodová J.

2015-01-01

Full Text Available The aim of the review was to analyze the ways of microbial contamination, the protective mechanism of egg, and factors that affect the quantity of contamination and microbial penetration. Eggs can be contaminated during their formation in the infected reproductive organs of hens or after laying, when eggs are exposed to contaminated environment. The eggs are equipped against microbial contamination by several protective mechanisms comprising the presence of cuticle, eggshell, eggshell membranes, occurrence of some antibacterial proteins, and high pH value of albumen. There are several factors that affect the quantity of microbial contamination and penetration such as species of bacteria, the amount of microorganisms, storage conditions, quality of eggshell or number of pores.

Solar Development on Contaminated and Disturbed Lands

Energy Technology Data Exchange (ETDEWEB)

Macknick, Jordan [National Renewable Energy Lab. (NREL), Golden, CO (United States); Lee, Courtney [National Renewable Energy Lab. (NREL), Golden, CO (United States); Mosey, Gail [National Renewable Energy Lab. (NREL), Golden, CO (United States); Melius, Jenny [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2013-12-01

Land classified as contaminated and disturbed across the United States has the potential to host developments of utility-scale solar power. This report examines the prospect of developing utility- and commercial-scale concentrated solar power (CSP) and solar photovoltaics (PV) technologies on degraded and environmentally contaminated lands. The potential for solar development on contaminated anddisturbed lands was assessed, and for the largest and highest solar resource sites, the economic impacts and feasibility were evaluated. Developing solar power on contaminated and disturbed lands can help create jobs and revitalize local and state economies, and selecting these sites over greenfield sites can potentially have permitting and environmental mitigation advantages. The U.S.Department of Energy (DOE) SunShot goals call for 632 GW of PV and 83 GW of CSP to be deployed by 2050. Conservative land-use estimates of this study (10 acres per megawatt) show that there are disturbed and environmentally contaminated lands throughout the country that could be suitable for utility-scale solar power, and, that there is sufficient land area to meet SunShot solar deployment goals. The purpose of this assessment is to improve the understanding of these sites and facilitate solar developers' selection of contaminated and disturbed sites for development.

9 CFR 113.30 - Detection of Salmonella contamination.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Detection of Salmonella contamination... REQUIREMENTS Standard Procedures § 113.30 Detection of Salmonella contamination. The test for detection of Salmonella contamination provided in this section shall be conducted when such a test is prescribed in an...

9 CFR 113.32 - Detection of Brucella contamination.

Science.gov (United States)

2010-01-01

... 9 Animals and Animal Products 1 2010-01-01 2010-01-01 false Detection of Brucella contamination... REQUIREMENTS Standard Procedures § 113.32 Detection of Brucella contamination. The test for detection of Brucella contamination provided in this section shall be conducted when such a test is prescribed in an...

Current university and USDA lab cotton contamination research

Science.gov (United States)

U.S. cotton is considered to have some of the lowest levels of contamination in the world. However, that reputation is in jeopardy as complaints of contamination from domestic and foreign mills are on the rise. Cotton contamination can be classified under four major categorizes: fabrics and strings ...

The tolerance efficiency of Panicum maximum and Helianthus annuus in TNT-contaminated soil and nZVI-contaminated soil.

Science.gov (United States)

Jiamjitrpanich, Waraporn; Parkpian, Preeda; Polprasert, Chongrak; Laurent, François; Kosanlavit, Rachain

2012-01-01

This study was designed to compare the initial method for phytoremediation involving germination and transplantation. The study was also to determine the tolerance efficiency of Panicum maximum (Purple guinea grass) and Helianthus annuus (Sunflower) in TNT-contaminated soil and nZVI-contaminated soil. It was found that the transplantation of Panicum maximum and Helianthus annuus was more suitable than germination as the initiate method of nano-phytoremediation potting test. The study also showed that Panicum maximum was more tolerance than Helianthus annuus in TNT and nZVI-contaminated soil. Therefore, Panicum maximum in the transplantation method should be selected as a hyperaccumulated plant for nano-phytoremediation potting tests. Maximum tolerance dosage of Panicum maximum to TNT-concentration soil was 320 mg/kg and nZVI-contaminated soil was 1000 mg/kg in the transplantation method.

Active airborne contamination control using electrophoresis

International Nuclear Information System (INIS)

Veatch, B.D.

1994-01-01

In spite of our best efforts, radioactive airborne contamination continues to be a formidable problem at many of the Department of Energy (DOE) weapons complex sites. For workers that must enter areas with high levels of airborne contamination, personnel protective equipment (PPE) can become highly restrictive, greatly diminishing productivity. Rather than require even more restrictive PPE for personnel in some situations, the Rocky Flats Plant (RFP) is actively researching and developing methods to aggressively combat airborne contamination hazards using electrophoretic technology. With appropriate equipment, airborne particulates can be effectively removed and collected for disposal in one simple process. The equipment needed to implement electrophoresis is relatively inexpensive, highly reliable, and very compact. Once airborne contamination levels are reduced, less PPE is required and a significant cost savings may be realized through decreased waste and maximized productivity. Preliminary ''cold,'' or non-radioactive, testing results at the RFP have shown the technology to be effective on a reasonable scale, with several potential benefits and an abundance of applications

Honey bees as indicators of radionuclide contamination: exploring colony variability and temporal contaminant accumulation

International Nuclear Information System (INIS)

Haarmann, T.K.

1997-01-01

Two aspects of using honey bees, Apis mellifera, as indicators of environmental radionuclide contamination were investigated: colony variability and temporal contaminant accumulation. Two separate field experiments were conducted in areas with bioavailable radionuclide contamination. Bees were collected from colonies, analysed for concentrations of radionuclides, and the results were compared using graphical and statistical methods. The first experiment indicates that generally a low variability exists between samples collected within the same colony. A higher variability exists between samples collected from adjacent colonies. Levels of tritium and sodium-22 found in samples taken from similar colonies were inconsistent, while levels of cobalt-57, cobalt-60 and manganese-54 were consistent. A second experiment investigated the accumulation of radionuclides over time by comparing colonies that had been in the study area for different periods of time. This experiment demonstrated that there is indeed a significant accumulation of radionuclides within colonies

Radiological assessment of radioactive contamination on private clothing

International Nuclear Information System (INIS)

Schartmann, F.; Thierfeldt, S.

2003-01-01

In the very rare, cases where private clothing of persons working in a nuclear installation are inadvertently contaminated and this contamination is not detected when leaving the facility, there may be radiological consequences for this person as well as for members of his or her family. The VGB (Technische Vereinigung der Grosskraftwerksbetreiber) in Germany has investigated in detail the spread of contamination in nuclear power plants. Part of this evaluation programme was a radiological analysis which has been carried out by Brenk Systemplanung GmbH (Aachen/Germany). The radiological analysis started with the definition of the source term. It is highly unlikely that activities of more than 5 kBq 60 Co could leave a plant undetected on the body or the clothes. Nevertheless activities up to 50 kBq and different nuclide vectors were regarded. It has been found that 60 Co is the most important contaminant. The radiological analysis focusses on two types of contamination: particles and surface contamination. The pathways by which such a contamination can lead to an exposure by external irradiation or by ingestion depend on the type of contamination and are analysed in detail. For example, a particle could be retained in pockets or other parts of clothing and may lead to prolonged external irradiation until the piece of clothing is washed. The analysis is performed on the basis of conservative to realistic assumptions. In conclusion, the analysis has shown that especially particle contamination needs to be focussed on. However, by the advanced detection equipment in German plants doses which may pose a health hazard can safely be excluded. (authors)

Does modifying personal responsibility moderate the mental contamination effect?

Science.gov (United States)

Kennedy, Tinisha S; Simonds, Laura M

2017-12-01

Mental contamination is the psychological sense of internal dirtiness that arises in the absence of physical contact with a perceived contaminant. Mental contamination can be evoked through imagining perpetrating a moral transgression. This study experimentally evoked mental contamination by asking men to imagine perpetrating a non-consensual kiss. It explored whether reducing sense of personal responsibility for the kiss moderated the mental contamination effect. Male students (N = 60) imagined giving either a consensual or non-consensual kiss. Personal responsibility for the kiss was manipulated in one of two non-consensual kiss conditions by way of the inclusion of social influence information. Feelings of mental contamination were assessed by self-report and through a behavioural index. Mental contamination was successfully induced in the two non-consensual kiss conditions. There was evidence to support the hypothesis that reducing personal responsibility might moderate specific components of mental contamination (shame, dirtiness and urge to cleanse). The effect of responsibility modification was evident in the self-report measures, but not in the behavioural index. The sample comprised male university students which limits generalizability of the findings. The behavioural assessment of mental contamination was limited to a proxy measure. Imagined moral violations are associated with increases in indices of mental contamination. Further research should investigate whether feelings of shame, dirtiness and urge to cleanse are particularly responsive to responsibility modifications. Copyright © 2017 Elsevier Ltd. All rights reserved.

Dispersion, deposition and resuspension of atmospheric contaminants

International Nuclear Information System (INIS)

Anon.

1985-01-01

The following topics are discussed: dry deposition, oil shale fugitive air emissions, particle resuspension and translocation, theoretical studies and applications, and processing of emissions by clouds and precipitation. The concentration of contaminant species in air is governed by the rate of input from sources, the rate of dilution or dispersion as a result of air turbulence, and the rate of removal to the surface by wet and dry deposition processes. Once on the surface, contaminants also may be resuspended, depending on meteorological and surface conditions. An understanding of these processes is necessary for accurate prediction of exposures of hazardous or harmful contaminants to humans, animals, and crops. In the field, plume dispersion and plume depletion by dry deposition were studied by the use of tracers. Dry deposition was investigated for particles of both respiration and inhalation interest. Complementary dry deposition studies of particles to rock canopies were conducted under controlled conditions in a wind tunnel. Because of increasing concern about hazardous, organic gases in the atmosphere some limited investigations of the dry deposition of nitrobenzene to a lichen mat were conducted in a stirred chamber. Resuspension was also studied using tracers and contaminated surfaces and in the wind tunnel. The objective of the resuspension studies was to develop and verify models for predicting the airborne concentrations of contaminants over areas with surface contamination, develop resuspension rate predictors for downwind transport, and develop predictors for resuspension input to the food chain. These models will be of particular relevance to the evaluation of deposition and resuspension of both radionuclides and chemical contaminants

Particle contamination in vacuum systems

International Nuclear Information System (INIS)

Martignac, J.; Bonin, B.; Henriot, C.; Poupeau, J.P.; Koltchakian, I.; Kocic, D.; Herbeaux, Ch.; Marx, J.P.

1996-01-01

Many vacuum devices, like RF cavities, are sensitive to particle contamination. This fact has motivated a considerable effort of cleanliness from the SRF community. The present paper reports the first results of a general study trying to identify the most contaminating steps during assembly and vacuum operation of the cavity. The steps investigated here are gasket assembly, evacuation and venting of the vacuum system, and operation of sputter ion pumps. (author)

Particle contamination in vacuum systems

International Nuclear Information System (INIS)

Martignac, J.; Bonin, B.; Henriot, C.; Poupeau, J.P.; Koltchakian, I.; Kocic, D.; Herbeaux, Ch.; Marx, J.P.

1996-01-01

Many vacuum devices, like RF cavities, are sensitive to particle contamination. This fact has motivated a considerable effort of cleanliness from the SRF community. The first results of a general study trying to identify the most contaminating steps during assembly and vacuum operation of the cavity is reported. The steps investigated here are gasket assembly, evacuation and venting of the vacuum system, and operation of sputter ion pumps. (author)

Assessment of Surface Water Contamination from Coalbed Methane Fracturing-Derived Volatile Contaminants in Sullivan County, Indiana, USA.

Science.gov (United States)

Meszaros, Nicholas; Subedi, Bikram; Stamets, Tristan; Shifa, Naima

2017-09-01

There is a growing concern over the contamination of surface water and the associated environmental and public health consequences from the recent proliferation of hydraulic fracturing in the USA. Petroleum hydrocarbon-derived contaminants of concern [benzene, toluene, ethylbenzene, and xylenes (BTEX)] and various dissolved cations and anions were spatially determined in surface waters around 15 coalbed methane fracking wells in Sullivan County, IN, USA. At least one BTEX compound was detected in 69% of sampling sites (n = 13) and 23% of sampling sites were found to be contaminated with all of the BTEX compounds. Toluene was the most common BTEX compound detected across all sampling sites, both upstream and downstream from coalbed methane fracking wells. The average concentration of toluene at a reservoir and its outlet nearby the fracking wells was ~2× higher than other downstream sites. However, one of the upstream sites was found to be contaminated with BTEX at similar concentrations as in a reservoir site nearby the fracking well. Calcium (~60 ppm) and sulfates (~175 ppm) were the dominant cations and anions, respectively, in surface water around the fracking sites. This study represents the first report of BTEX contamination in surface water from coalbed methane hydraulic fracturing wells.

Superfund and Toxic Release Inventory Sites - MDC_ContaminatedSite

Data.gov (United States)

NSGIC Local Govt | GIS Inventory — A point feature class of open DERM Contaminated sites - see phase code for status of site. Contaminated sites identifies properties where environmental contamination...

Statistical sampling strategies for survey of soil contamination

NARCIS (Netherlands)

Brus, D.J.

2011-01-01

This chapter reviews methods for selecting sampling locations in contaminated soils for three situations. In the first situation a global estimate of the soil contamination in an area is required. The result of the surey is a number or a series of numbers per contaminant, e.g. the estimated mean

X-231B technology demonstration for in situ treatment of contaminated soil: Contaminant characterization and three dimensional spatial modeling

International Nuclear Information System (INIS)

West, O.R.; Siegrist, R.L.; Mitchell, T.J.; Pickering, D.A.; Muhr, C.A.; Greene, D.W.; Jenkins, R.A.

1993-11-01

Fine-textured soils and sediments contaminated by trichloroethylene (TCE) and other chlorinated organics present a serious environmental restoration challenge at US Department of Energy (DOE) sites. DOE and Martin Marietta Energy Systems, Inc. initiated a research and demonstration project at Oak Ridge National Laboratory. The goal of the project was to demonstrate a process for closure and environmental restoration of the X-231B Solid Waste Management Unit at the DOE Portsmouth Gaseous Diffusion Plant. The X-231B Unit was used from 1976 to 1983 as a land disposal site for waste oils and solvents. Silt and clay deposits beneath the unit were contaminated with volatile organic compounds and low levels of radioactive substances. The shallow groundwater was also contaminated, and some contaminants were at levels well above drinking water standards. This document begins with a summary of the subsurface physical and contaminant characteristics obtained from investigative studies conducted at the X-231B Unit prior to January 1992 (Sect. 2). This is then followed by a description of the sample collection and analysis methods used during the baseline sampling conducted in January 1992 (Sect. 3). The results of this sampling event were used to develop spatial models for VOC contaminant distribution within the X-231B Unit

Influence of radioactive contaminants on absorbed dose estimates for radiopharmaceuticals

International Nuclear Information System (INIS)

Watson, E.E.; Stabin, M.G.

1986-01-01

Several popular radiopharmaceutical products contain low levels of radioactive contaminants. These contaminants increase the radiation absorbed dose to the patient without any increased benefit and, in some cases, with a decrease in image quality. The importance of a contaminant to the radiation dosimetry picture is a function of 1) the contaminant level, 2) the physical half-life of the contaminant, 3) the organ uptake and the biological half-time of the contaminant in the various body systems, and 4) the decay mode, energy, etc. of the contaminant. The general influence of these parameters is discussed in this paper; families of curves are included that reflect the changing importance of contaminant dosimetry with respect to the primary radionuclide as a function of these variables. Several specific examples are also given of currently used radiopharmaceutical products which can contain radioactive contaminants (I-123, In-111, Tl-201, Ir-191m, Rb-82, Au-195m). 7 references, 8 figures, 4 tables

Eliminating PCR contamination

International Nuclear Information System (INIS)

Fox, J.C.; Ait-Khaled, Mounir; Webster, Alison; Emery, V.C.

1991-01-01

The sensitivity of polymerase chain reaction (PCR) can mean that even very low levels of contamination with the target DNA will result in a positive signal. At present this aspect is a major limitation in the use of PCR as a routine diagnostic method. By exposing PCR reagents to UV light, contaminating DNA can be inactivated, thus providing an opportunity to eradicate false positive reactions. UV irradiation was applied to PCR systems used for detection of human cytomegalovirus CMV and human immunodeficiency virus (HIV) and shown to be effective in eradicating both laboratory encountered contamination and plasmid DNA (below 100 pg) added to PCR systems prior to UV exposure. Sensitivity of a PCR system to amplify the long terminal repeat (LTR) sequence of HIV-1 was not affected by the irradiation procedure; however, ultimate sensitivity of a PCR system for the amplification of an early gene pro-motor sequence of the CMV genome was reduced 1000-fold. UV irradiation did not affect the size of the PCR product as determined by strand separating polyacrylamide gel electrophoresis of a 32 P-labelled amplimer. Thus, a simple pre-exposure to UV light would seem a worth-wile step to incorporate into PCR protocols provided that the effects on sensitivity have been determined empirically for each PCR system. (author). 11 refs.; 3 figs

Alternative method for determination of contaminated heparin using chiral recognition.

Science.gov (United States)

Szekely, J; Collins, M; Currie, C A

2014-05-15

Since 2008 a significant amount of work has focused on the development of methods to analyze contaminated heparin. This work focuses on utilizing heparin's ability to serve as a chiral selector as a means for determining contamination. Specifically, the effect of contamination on the separation of pheniramine and chloroquine enantiomers was explored. Separations were conducted using heparin contaminated with chondroitin sulfate at varying levels. For each pair of enantiomers, electrophoretic mobility and resolution were calculated. For pheniramine enantiomers, an increase in contamination leads to a decrease in the electrophoretic mobility and resolution. A linear relationship between contamination level and electrophoretic mobility of the pheniramine enantiomers was observed for the entire contamination range. A linear relationship was also found between contamination level and resolution of the enantiomers between 0 and 70 percent contamination. For the separation of chloroquine enantiomers, it was found that at low levels of contamination, the resolution of enantiomers was increased due to the secondary interaction between the chloroquine enantiomers and the chondroitin sulfate. Results of this study illustrate the potential of using chiral recognition as a means to determine heparin contamination as well as the improvement of the chiral resolution of chloroquine with the additional of low levels of chondroitin sulfate A. Copyright © 2014 Elsevier B.V. All rights reserved.

Factors influencing the contamination rate of human organ-cultured corneas.

Science.gov (United States)

Röck, Daniel; Wude, Johanna; Bartz-Schmidt, Karl U; Yoeruek, Efdal; Thaler, Sebastian; Röck, Tobias

2017-12-01

To assess the influence of donor, environment and storage factors on the contamination rate of organ-cultured corneas, to consider the microbiological species causing corneal contamination and to investigate the corresponding sensitivities. Data from 1340 consecutive donor corneas were analysed retrospectively. Logistic regression analysis was used to assess the influence of different factors on the contamination rate of organ-cultured corneas for transplantation. The mean annual contamination rate was 1.8 ± 0.4% (range: 1.3-2.1%); 50% contaminations were of fungal origin with exclusively Candida species, and 50% contaminations were of bacterial origin with Staphylococcus species being predominant. The cause of donor death including infection and multiple organ dysfunction syndrome increased the risk of bacterial or fungal contamination during organ culture (p = 0.007 and p = 0.014, respectively). Differentiating between septic and aseptic donors showed an increased risk of contamination for septic donors (p = 0.0020). Mean monthly temperature including warmer months increased the risk of contamination significantly (p = 0.0031). Sex, donor age, death to enucleation, death to corneoscleral disc excision and storage time did not increase the risk of contamination significantly. The genesis of microbial contamination in organ-cultured donor corneas seems to be multifactorial. The main source of fungal or bacterial contamination could be resident species from the skin flora. The rate of microbial contamination in organ-cultured donor corneas seems to be dependent on the cause of donor death and mean monthly temperature. © 2017 Acta Ophthalmologica Scandinavica Foundation. Published by John Wiley & Sons Ltd.

Optimal Aquifer Pumping Policy to Reduce Contaminant Concentration

Directory of Open Access Journals (Sweden)

Ali Abaei

2012-01-01

Full Text Available Different sources of ground water contamination lead to non-uniform distribution of contaminant concentration in the aquifer. If elimination or containment of pollution sources was not possible, the distribution of contaminant concentrations could be modified in order to eliminate peak concentrations using optimal water pumping discharge plan. In the present investigation Visual MODFLOW model was used to simulate the flow and transport in a hypothetic aquifer. Genetic Algorithm (GA also was applied to optimize the location and pumping flow rate of wells in order to reduce contaminants peak concentrations in aquifer.

Radioactive contamination mapping system detailed design report

International Nuclear Information System (INIS)

Bauer, R.G.; O'Callaghan, P.B.

1996-08-01

The Hanford Site's 100 Area production reactors released radioactively and chemically contaminated liquids into the soil column. The primary source of the contaminated liquids was reactor coolant and various waste waters released from planned liquid discharges, as well as pipelines, pipe junctions, and retention basins leaking into the disposal sites. Site remediation involves excavating the contaminated soils using conventional earthmoving techniques and equipment, treating as appropriate, transporting the soils, and disposing the soils at ERDF. To support remediation excavation, disposal, and documentation requirements, an automated radiological monitoring system was deemed necessary. The RCMS (Radioactive Contamination Mapping System) was designed to fulfill this need. This Detailed Design Report provides design information for the RCMS in accordance with Bechtel Hanford, Inc. Engineering Design Project Instructions

Radioactive contamination in monitors received for calibration

International Nuclear Information System (INIS)

Dias, Paulo S.; Santos, Gilvan C. dos; Brunelo, Maria Antonieta G.; Paula, Tiago C. de; Pires, Marina A.; Borges, Jose C.

2013-01-01

The Calibration Laboratory - LABCAL, from the Research Center for Metrology and Testing - METROBRAS, MRA Comercio de Instrumentos Eletronicos Ltda., began activities in October 2008 and, in August 2009, decided to establish a procedure for monitoring tests, external and internal, of all packages received from customers, containing instruments for calibration. The aim was to investigate possible contamination radioactive on these instruments. On July 2011, this procedure was extended to packagings of personal thermoluminescent dosemeters - TLD, received by the newly created Laboratory Laboratorio de Dosimetria Pessoal - LDP . In the monitoring procedure were used monitors with external probe, type pancake, MRA brand, models GP - 500 and MIR 7028. During the 37 months in which this investigation was conducted, were detected 42 cases of radioactive contamination, with the following characteristics: 1) just one case was personal dosimeter, TLD type; 2) just one case was not from a packing from nuclear medicine service - was from a mining company; 3) contamination occurred on packs and instruments, located and/or widespread; 4) contamination values ranged from slightly above the level of background radiation to about a thousand fold. Although METROBRAS has facilities for decontamination, in most cases, especially those of higher contamination, the procedure followed was to store the contaminated material in a room used for storage of radioactive sources. Periodically, each package and/or instrument was monitored, being released when the radiation level matched the background radiation. Every contamination detected, the client and/or owner of the instrument was informed. The Brazilian National Energy Commission - CNEN, was informed, during your public consultation for reviewing the standard for nuclear medicine services, held in mid-2012, having received from METROBRAS the statistical data available at the time. The high frequency of contamination detected and the high

Biological Treatment of Petroleum in Radiologically Contaminated Soil

Energy Technology Data Exchange (ETDEWEB)

BERRY, CHRISTOPHER

2005-11-14

This chapter describes ex situ bioremediation of the petroleum portion of radiologically co-contaminated soils using microorganisms isolated from a waste site and innovative bioreactor technology. Microorganisms first isolated and screened in the laboratory for bioremediation of petroleum were eventually used to treat soils in a bioreactor. The bioreactor treated soils contaminated with over 20,000 mg/kg total petroleum hydrocarbon and reduced the levels to less than 100 mg/kg in 22 months. After treatment, the soils were permanently disposed as low-level radiological waste. The petroleum and radiologically contaminated soil (PRCS) bioreactor operated using bioventing to control the supply of oxygen (air) to the soil being treated. The system treated 3.67 tons of PCRS amended with weathered compost, ammonium nitrate, fertilizer, and water. In addition, a consortium of microbes (patent pending) isolated at the Savannah River National Laboratory from a petroleum-contaminated site was added to the PRCS system. During operation, degradation of petroleum waste was accounted for through monitoring of carbon dioxide levels in the system effluent. The project demonstrated that co-contaminated soils could be successfully treated through bioventing and bioaugmentation to remove petroleum contamination to levels below 100 mg/kg while protecting workers and the environment from radiological contamination.

Rehabilitation of the contaminated territories

International Nuclear Information System (INIS)

Ageets, V.Yu.; Kenigsberg, Ya.Eh.; Skurat, V.V.; Tikhonova, L.E.; Shevchuk, V.E.; Ipat'ev, V.A.; Klimova, T.A.

1998-01-01

The purpose of the activity is development of the scientific reasonable projects of socio-economic and social-psychological rehabilitation of specific areas and populated localities on the contaminated territories of the both Gomel and Mogilev Regions. The results of economic researches allow to decrease expenses for realization of protective measures, to increase feedback of counter-measures, to speed up process of development of the plans and their realization, to decrease the labour input of planning of the rehabilitation measures, to increase quantity of considered alternative variants of strategy of the contaminated regions rehabilitation. On the basis of the sociological and psychological researches the recommendations for the most effective formation of adaptation strategies of behaviour of the people on the contaminated territories, formation of post accidental culture and active life image at teenagers, ways of fastening of youth in these areas, more address specialized social support and protection of the irradiated persons, perfection of social demographic policy on rehabilitated territories are offered. In the report are described following directions: scientific ground and development of the complex programmes of rehabilitation of administrative regions on the contaminated territories; development of administration system of the social economical development of the territories having suffered after the Chernobyl accident; social support and socio-psychological rehabilitation of the population of Belarus

Contaminant transport modeling studies of Russian sites

International Nuclear Information System (INIS)

Tsang, Chin-Fu

1993-01-01

Lawrence Berkeley Laboratory (LBL) established mechanisms that promoted cooperation between U.S. and Russian scientists in scientific research as well as environmental technology transfer. Using Russian experience and U.S technology, LBL developed approaches for field investigations, site evaluation, waste disposal, and remediation at Russian contaminated sites. LBL assessed a comprehensive database as well as an actual, large-scale contaminated site to evaluate existing knowledge of and test mathematical models used for the assessment of U.S. contaminated sites

Pharmaceutical product cross-contamination: industrial and clinical ...

African Journals Online (AJOL)

problems. Pharmaceutical product cross-contamination is a serious problem which has been detected as an obstacle ... In the pharmaceutical care of patients in developed countries, cross-contamination ..... neonatal intensive care units.

Contaminant Hydrogeology, 2nd Edition

Science.gov (United States)

Smith, James E.

Groundwater is a valuable resource that has received much attention over the last couple of decades. Extremely large sums of money have been and will be spent on groundwater contamination problems and the public has become increasingly sensitive to groundwater issues. Groundwater contamination has even become the subject of a major Hollywood movie with the recent release of A Civil Action starring John Travolta. The high profile of groundwater contaminant problems, the associated relatively strong job market over the last 20 years, and the general shift toward an environmental emphasis in science and engineering have resulted in a sustained high demand for senior undergraduate courses and graduate programs in hydrogeology Many voice the opinion that we have seen the peak demand for hydrogeologists pass, but the placement of graduates from hydrogeology programs into career-oriented positions has remained very high.

Environmental contaminants, ecosystems and human health

Energy Technology Data Exchange (ETDEWEB)

Majumdar, S.K.; Miller, E.W.; Brenner, F.J. [eds.] [Lafayette College, Easton, PA (United States). Dept. of Biology

1995-12-31

The authors cover a variety of concerns regarding the adverse impacts of contaminants on ecosystems and human health. The twelve chapters in the first section of the text address the impact of contaminants on ecosystem function, and ten of the remaining twenty-two chapters are devoted to the effects of contaminants on human health. Part three presents eight case studies in humans, while the final four chapters provide the reader with an assessment of environmental problems and analyses. Two chapters, on the health effects of power plant generated air pollution and on black lung disease, have been abstracted separately for the IEA Coal Research CD-ROM.

Nuclear, biological and chemical contamination survivability of Army material

International Nuclear Information System (INIS)

Feeney, J.J.

1987-01-01

Army Regulation (AR) 70-71, Nuclear, Biological and Chemical (NBC) Contamination Survivability of Army Material, published during 1984, establishes Army policy and procedures for the development and acquisition of material to ensure its survivablility and sustainability on the NBC-contaminated battlefield. This regulation defines NBC contamination as a term that includes both the individual and collective effects of residual radiological, biological, and chemical contamination. AR 70-71 applies to all mission-essential equipment within the Army. NBC contamination survivability is the capability of a system and its crew to withstand an NBC-contaminated environment, including decontamination, without losing the ability to accomplish the assigned mission. Characteristics of NBC contamination survivability are decontaminability, hardness, and compatability. These characteristics are engineering design criteria which are intended for use only in a developmental setting. To comply with AR 70-71, each mission-essential item must address all three criteria. The Department of Defense (DOD) has published a draft instruction addressing acquisition of NBC contamination survivable systems. This instruction will apply throughout DOD to those programs, systems and subsystems designated by the Secretary of Defense as major systems acquisition programs and to those non-major systems that have potential impact on critical functions

Skin dose rate conversion factors after contamination with radiopharmaceuticals: influence of contamination area, epidermal thickness and percutaneous absorption

International Nuclear Information System (INIS)

Covens, P; Berus, D; Caveliers, V; Struelens, L; Vanhavere, F; Verellen, D

2013-01-01

Skin contamination with radiopharmaceuticals can occur during biomedical research and daily nuclear medicine practice as a result of accidental spills, after contact with bodily fluids of patients or by inattentively touching contaminated materials. Skin dose assessment should be carried out by repeated quantification to map the course of the contamination together with the use of appropriate skin dose rate conversion factors. Contamination is generally characterised by local spots on the palmar surface of the hand and complete decontamination is difficult as a result of percutaneous absorption. This specific issue requires special consideration as to the skin dose rate conversion factors as a measure for the absorbed dose rate to the basal layer of the epidermis. In this work we used Monte Carlo simulations to study the influence of the contamination area, the epidermal thickness and the percutaneous absorption on the absorbed skin dose rate conversion factors for a set of 39 medical radionuclides. The results show that the absorbed dose to the basal layer of the epidermis can differ by up to two orders of magnitude from the operational quantity H p (0.07) when using an appropriate epidermal thickness in combination with the effect of percutaneous absorption. (paper)

Owls as biomonitors of environmental contamination

Science.gov (United States)

Steven R. Sheffield

1997-01-01

Much like the caged canary used by miners, a plethora of wildlife species have been promoted as biomonitors of environmental contamination. These species provide an "early warning system" for toxic contaminants in the environment. Species promoted as useful biomonitors share many common life history characters, such as wide distribution, territorial, non-...

Plutonium contamination in the Maralinga Tjarutja lands

International Nuclear Information System (INIS)

Johnston, P.N.; Lokan, K.H.; Richardson, C.K.; Williams, G.A.

1989-08-01

Nuclear weapons trials conducted at Maralinga from 1960 to 1963 resulted in contamination of large areas of land with low levels of plutonium. Ground and aerial surveys and soil sampling conducted between 1984 and 1987 showed that this contamination extended beyond the boundaries of the area still controlled by the Commonwealth Government into the Maralinga Tjarutja lands. Levels of contamination beyond the boundaries of the former test range were found to be low, and were generally undetectable for all but the most sensitive measurement techniques. Soil sampling combined with long laboratory counting was initially used to define the trace levels but the contamination was found to be particulate with a surface density of particles too low for this to be a generally useful technique. The results are presented of in-situ gamma-ray spectrometry using a portable germanium (Ge) detector to measure contamination levels of plutonium to well below 1 kBq m -2 in the Maralinga Tjarutja lands to the north and north-west of the Maralinga test site. 8 refs., 10 figs., 10 tabs

Organic contaminants in onsite wastewater treatment systems

Science.gov (United States)

Conn, K.E.; Siegrist, R.L.; Barber, L.B.; Brown, G.K.

2007-01-01

Wastewater from thirty onsite wastewater treatment systems was sampled during a reconnaissance field study to quantify bulk parameters and the occurrence of organic wastewater contaminants including endocrine disrupting compounds in treatment systems representing a variety of wastewater sources and treatment processes and their receiving environments. Bulk parameters ranged in concentrations representative of the wide variety of wastewater sources (residential vs. non-residential). Organic contaminants such as sterols, surfactant metabolites, antimicrobial agents, stimulants, metal-chelating agents, and other consumer product chemicals, measured by gas chromatography/mass spectrometry were detected frequently in onsite system wastewater. Wastewater composition was unique between source type likely due to differences in source water and chemical usage. Removal efficiencies varied by engineered treatment type and physicochemical properties of the contaminant, resulting in discharge to the soil treatment unit at ecotoxicologically-relevant concentrations. Organic wastewater contaminants were detected less frequently and at lower concentrations in onsite system receiving environments. Understanding the occurrence and fate of organic wastewater contaminants in onsite wastewater treatment systems will aid in minimizing risk to ecological and human health.

Microbial Contamination Level Profiles Attributed to Contamination of Beef Carcasses, Personnel, and Equipment: Case of Small and Medium Enterprise Slaughterhouses.

Science.gov (United States)

Wambui, Joseph; Lamuka, Peter; Karuri, Edward; Matofari, Joseph; Njage, Patrick Murigu Kamau

2018-04-01

The microbial contamination level profiles (MCLPs) attributed to contamination of beef carcasses, personnel, and equipment in five Kenyan small and medium enterprise slaughterhouses were determined. Aerobic plate counts, Enterobacteriaceae, Staphylococcus, and Salmonella were used to determine contamination at four different slaughter stages, namely, dehiding, evisceration, splitting, and dispatch. Microbiological criteria of the four microorganisms were used to score contamination levels (CLs) as poor (0), poor to average (1), average (2), or good (3). MCLPs were further assigned to carcasses, personnel, and equipment at each stage by summing up the CL scores. The CL score attributed to aerobic plate count contamination was 2 or 3 for carcasses but 0 for personnel and equipment in almost all slaughterhouses. A score of 0 on carcasses was mostly attributed to Enterobacteriaceae at evisceration and to Salmonella at dehiding and evisceration. In addition, a score of 0 was mostly attributed to Staphylococcus contamination of personnel at dehiding. A score of 3 was attributed mostly to Enterobacteriaceae on hands at splitting, whereas a score of 2 was mostly attributed to the clothes at dehiding and evisceration. A CL score of 3 was mostly attributed to Enterobacteriaceae and Salmonella contamination of equipment at dehiding and splitting, respectively. Although CLs attributed to contamination of carcasses, personnel, and equipment ranged from 0 to 3, the maximum MCLP score of 9 was only attained in carcasses from two slaughterhouses at dehiding and from one slaughterhouse at dispatch. There is, therefore, a lot of room for small and medium enterprise slaughterhouses to improve their food safety objectives by improving food safety management systems at the points characterized by low CL scores.

Control of everyday contamination problems in a hot cell laboratory

International Nuclear Information System (INIS)

Buch, R.

1983-01-01

For handling unsealed radioactive materials, contamination monitoring and the application of appropriate methods for the prevention of contamination are essential measures to achieve radiation protection safety at the working place and during operation. It is essential to know which are the contamination sources and which circumstances may lead to contamination release and diffusion. Depending on the kind of contamination and the extent of the resulting radiation exposure, suitable easy-to-use measuring equipment is necessary. The lecture shows how contamination release can be limited or prevented, and detected in due time by the use of appropriate measuring instruments, so that contaminations and the ways of decontaminating do not necessarily cause increased dose rates. (orig.) [de

The contamination factory

International Nuclear Information System (INIS)

Anon.

1991-01-01

In 1989 the Senate Committee on Armed Services asked the Congressional Office of Technology Assessment (OTA) to investigate the environmental and public health impacts of contamination at the nation's nuclear weapons complex and to review the Department of Energy's (DOE) program to clean up past contamination and manage huge quantities of radioactive and hazardous wastes. The DOE Environmental Restoration/Waste Management Program is a massive, multibillion-dollar effort engaging state governments and several federal agencies, and including some of the most technically challenging environmental characterization and remediation projects ever attempted. Congress recognized the enormity of DOE's environmental and legal problems and is interested in insuring that the cleanup program is both adequate and efficient. This summary of the OTA report has been adapted for publication in the Bulletin

The organic contamination level based on the total soil mass is not a proper index of the soil contamination intensity

Science.gov (United States)

Hung, H.-W.; Daniel, Sheng G.; Lin, T.-F.; Su, Y.; Chiou, C.T.

2009-01-01

Concentrations of organic contaminants in common productive soils based on the total soil mass give a misleading account of actual contamination effects. This is attributed to the fact that productive soils are essentially water-saturated, with the result that the soil uptake of organic compounds occurs principally by partition into the soil organic matter (SOM). This report illustrates that the soil contamination intensity of a compound is governed by the concentration in the SOM (Com) rather than by the concentration in whole soil (Cs). Supporting data consist of the measured levels and toxicities of many pesticides in soils of widely differing SOM contents and the related levels in in-situ crops that defy explanation by the Cs values. This SOM-based index is timely needed for evaluating the contamination effects of food crops grown in different soils and for establishing a dependable priority ranking for intended remediation of numerous contamination sites.

[Decorporation agents for internal radioactive contamination].

Science.gov (United States)

Ohmachi, Yasushi

2015-01-01

When radionuclides are accidentally ingested or inhaled, blood circulation or tissue/organ deposition of the radionuclides causes systemic or local radiation effects. In such cases, decorporation therapy is used to reduce the health risks due to their intake. Decorporation therapy includes reduction and/or inhibition of absorption from the gastrointestinal tract, isotopic dilution, and the use of diuretics, adsorbents, and chelating agents. For example, penicillamine is recommended as a chelating agent for copper contamination, and diethylene triamine pentaacetic acid is approved for the treatment of internal contamination with plutonium. During chelation therapy, the removal effect of the drugs should be monitored using a whole-body counter and/or bioassay. Some authorities, such as the National Council on Radiation Protection and Measurements and International Atomic Energy Agency, have reported recommended decorporation agents for each radionuclide. However, few drugs are approved by the US Food and Drug Administration, and many are off-label-use agents. Because many decontamination agents are drugs that have been available for a long time and have limited efficacy, the development of new, higher-efficacy drugs has been carried out mainly in the USA and France. In this article, in addition to an outline of decorporation agents for internal radioactive contamination, an outline of our research on decorporation agents for actinide (uranium and plutonium) contamination and for radio-cesium contamination is also presented.

Treatment of HMX and RDX contamination

International Nuclear Information System (INIS)

Card, R.E. Jr.; Autenrieth, R.

1998-03-01

HMX and RDX are often found in the soil, groundwater, and surface waters at facilities where they are manufactured as the result of negligent disposal methods. The toxicity of these compounds and their degradation products has led to concern about their fate in the environment and the potential for human exposure. HMX and RDX are recalcitrant in the environment with low rates of biodegradation and photolysis. Several methods of treating contaminated soils and waters have been developed and studied. Many of these technologies (i.e., carbon adsorption, oxidation, and chemical treatment) have been developed to treat munition plant wastewaters that are contaminated with explosives. These methods need to be adapted to remediate contaminated water. Other technologies such as bioremediation and composting are being developed as methods of remediating HMX and RDX contamination in a solid matrix. This report describes and evaluates each of these technologies. This report also describes the processes which affect HMX and RDX in the environment. The major transformation processes of RDX and HMX in the environment are biodegradation and photolysis. A major factor affecting the transport and treatment of RDX and HMX in soil-water environments is their sorption and desorption to soil particles. Finally, this report draws conclusions as to which treatment methods are currently most suitable for the remediation of contaminated soils and waters

Contamination awareness at the Dresden Nuclear Power Station

International Nuclear Information System (INIS)

Pagel, D.J.; Rath, W.C.

1986-01-01

Dresden Nuclear Power Station, which is located ∼ 60 miles southwest of Chicago near Morris, Illinois, has been generating electricity since 1960. Owned by Commonwealth Edison, Dresden was the nation's first privately financed nuclear station. On its site are three boiling water reactors (BWRs). Due to the contamination potential inherent with a reactor, a contamination trending program was created at the station. Studies had indicated a rise in contamination events during refueling outages. Further increases were due to specific work projects such as hydrolyzing operations. The investigations suggested that contract personnel also increased the number of events. In 1983, a contamination awareness program was created. The 1984 contamination awareness program was comprised of the following: (1) a statistical review in which trended contamination events were discussed. (2) A demonstration of protective clothing removal by an individual making various mistakes. (3) Scenarios were developed for use in mock work areas. (4) Upper management involvement. Because of the 1984 program, favorable attention has been focused on Dresden from the US Nuclear Regulatory Commission and the Institute of Nuclear Power Operations

Risk assessment and management of an oil contaminated aquifer

International Nuclear Information System (INIS)

Braxein, A.; Daniels, H.; Rouve, G.; Rubin, H.

1991-01-01

This paper concerns the provision of the basic information needed for the decision making process regarding the remedial measures leading to reutilization of an oil contaminated aquifer. The study refers to the case history of jet fuel contamination of an aquifer comprising part of the coastal aquifer of Israel. Due to that contamination two major water supply wells were abandoned. This study examines the use of numerical simulations in order to restore the contamination history of the aquifer. Such simulations also provide quantitative information needed for the decision making process regarding the future management of the contaminated aquifer

Contamination shield

International Nuclear Information System (INIS)

Bayer, W.; Pecornik, D.

1982-01-01

An acrylate resin is presented as contamination protection coating for components and instruments in nuclear facilities and for spent fuel transport containers. The resin is evaporated or sublimated at 130 0 C and can thus be removed easily from the protected component. The radioactive particles entrained during evaporation are retained by suitable filters. (TK) [de

Remediation of sites with dispersed radioactive contamination

International Nuclear Information System (INIS)

2004-01-01

To respond to the needs of Member States, the IAEA launched an environmental remediation project to deal with the problems of radioactive contamination worldwide. The IAEA environmental remediation project includes an IAEA Coordinated Research Project, as well as the participation of IAEA experts in concrete remediation projects when requested by individual Member States. The IAEA has prepared several documents dedicated to particular technical or conceptual areas, including documents on the characterization of contaminated sites, technical and non-technical factors relevant to the selection of a preferred remediation strategy and technique, overview of applicable techniques for environmental remediation,, options for the cleanup of contaminated groundwater and planning and management issues. In addition, a number of other IAEA publications dealing with related aspects have been compiled under different IAEA projects; these include TECDOCs on the remediation of uranium mill tailings, the decontamination of buildings and roads and the characterization of decommissioned sites. Detailed procedures for the planning and implementation of remedial measures have been developed over the past decade or so. A critical element is the characterization of the contamination and of the various environmental compartments in which it is found, in order to be able to evaluate the applicability of remediation techniques. The chemical or mineralogical form of the contaminant will critically influence the efficiency of the remediation technique chosen. Careful delineation of the contamination will ensure that only those areas or volumes of material that are actually contaminated are treated. This, in turn, reduces the amount of any secondary waste generated. The application of a remediation technique requires holistic studies examining the technical feasibility of the proposed measures, including analyses of their impact. Consequently, input from various scientific and engineering

CDC Study Finds Fecal Contamination in Pools

Science.gov (United States)

... Communication (404) 639-3286 CDC study finds fecal contamination in pools A study of public pools done ... The E. coli is a marker for fecal contamination. Finding a high percentage of E. coli-positive ...

Estimating exposure of terrestrial wildlife to contaminants

Energy Technology Data Exchange (ETDEWEB)

Sample, B.E.; Suter, G.W. II

1994-09-01

This report describes generalized models for the estimation of contaminant exposure experienced by wildlife on the Oak Ridge Reservation. The primary exposure pathway considered is oral ingestion, e.g. the consumption of contaminated food, water, or soil. Exposure through dermal absorption and inhalation are special cases and are not considered hereIN. Because wildlife mobile and generally consume diverse diets and because environmental contamination is not spatial homogeneous, factors to account for variation in diet, movement, and contaminant distribution have been incorporated into the models. To facilitate the use and application of the models, life history parameters necessary to estimate exposure are summarized for 15 common wildlife species. Finally, to display the application of the models, exposure estimates were calculated for four species using data from a source operable unit on the Oak Ridge Reservation.

Estimating exposure of terrestrial wildlife to contaminants

International Nuclear Information System (INIS)

Sample, B.E.; Suter, G.W. II.

1994-09-01

This report describes generalized models for the estimation of contaminant exposure experienced by wildlife on the Oak Ridge Reservation. The primary exposure pathway considered is oral ingestion, e.g. the consumption of contaminated food, water, or soil. Exposure through dermal absorption and inhalation are special cases and are not considered hereIN. Because wildlife mobile and generally consume diverse diets and because environmental contamination is not spatial homogeneous, factors to account for variation in diet, movement, and contaminant distribution have been incorporated into the models. To facilitate the use and application of the models, life history parameters necessary to estimate exposure are summarized for 15 common wildlife species. Finally, to display the application of the models, exposure estimates were calculated for four species using data from a source operable unit on the Oak Ridge Reservation

Radiation exposure to skin following radioactive contamination

International Nuclear Information System (INIS)

Baumann, H.; Beyermann, M.; Kraus, W.

1989-01-01

In the case of skin contamination intensive decontamination measures should not be carried out until the potential radiation exposure to the basal cell layer of the epidermis was assessed. Dose equivalent rates from alpha-, beta- or photon-emitting contaminants were calculated with reference to the surface activity for different skin regions as a function of radiation energy on the condition that the skin was healthy and uninjured and the penetration of contaminants through the epidermis negligible. The results have been presented in the form of figures and tables. In the assessment of potential skin doses, both radioactive decay and practical experience as to the decrease in the level of surface contamination by natural desquamation of the stratum corneum were taken into account. 9 figs., 5 tabs., 46 refs. (author)

Technology for reuse of contaminated concrete constituents

International Nuclear Information System (INIS)

Binkhorst, I.P.; Cornelissen, H.A.W.

1998-01-01

During decommissioning activities of nuclear installations, large amounts of contaminated concrete will have to be processed. All this concrete has to be treated and stored as radioactive waste, which implies major economical and environmental consequences. It was shown that the contamination is mainly concentrated in the porous cement stone. By separating this cement stone from the clean dense aggregate particles, a considerable volume reduction can be reached. KEMA has developed, designed and constructed a pilot plant scale test installation for separation of aggregate from contaminated concrete. The separation is based on a thermal treatment followed by milling and sieving. The clean aggregate can be re-used in concrete, whereas the (slightly) contaminated cement stone could be upgraded to a binder for concrete used in the nuclear industry. (author)

Natural revegetation of hydrocarbon-contaminated soil in semi-arid grasslands

International Nuclear Information System (INIS)

Bizecki Robson, D.; Knight, J. D.; Farrell, R. E.; Germida, J. J.

2004-01-01

Phytoremediation, or the use of plants to degrade and contain soil contaminants is considered a cost-effective decontaminant for sites contaminated by spills in the oil and gas producing areas of Western Canada. The objective of this study was to determine if contamination by hydrocarbons changes soil properties, species composition, and species abundance when compared with uncontaminated plots, and to identify species and functional groups unique to contaminated sites that may be further screened for their hydrocarbon-degrading ability. In pursuit of these objectives the effect of contamination on coverage, litter and bare ground was examined, differences in species composition between contaminated and uncontaminated sites were assessed, and the ability to fix nitrogen, and form mycorrhiza, life form, pollination mode, seed dispersal and reproduction mode of each species was determined. Results showed less vegetation and litter cover in contaminated plots, and significantly higher soil carbon to nitrogen ratios. Species diversity was also lower on contaminated sites, although species richness was not significantly different. Self-pollinated species were significantly more common on contaminated sites. Five grasses and three forbs were identified as tolerant of hydrocarbon-contaminated soils, with two grasses -- Agropyron smithii, and Agropyron trachycaulum -- being the most promising for reclamation. The low vegetation cover on contaminated plots is attributed to high pH and carbon to nitrogen ratios, and low nitrogen and phosphorus that results from soil disturbance. High electrical conductivity is also considered to adversely affect vegetation and litter cover on contaminated sites. 54 refs., 3 tabs., 1 fig

Natural revegetation of hydrocarbon-contaminated soil in semi-arid grasslands

Energy Technology Data Exchange (ETDEWEB)

Bizecki Robson, D.; Knight, J. D.; Farrell, R. E.; Germida, J. J. [University of Saskatchewan, Dept. of Soil Science, Saskatoon, SK (Canada)

2004-01-01

Phytoremediation, or the use of plants to degrade and contain soil contaminants is considered a cost-effective decontaminant for sites contaminated by spills in the oil and gas producing areas of Western Canada. The objective of this study was to determine if contamination by hydrocarbons changes soil properties, species composition, and species abundance when compared with uncontaminated plots, and to identify species and functional groups unique to contaminated sites that may be further screened for their hydrocarbon-degrading ability. In pursuit of these objectives the effect of contamination on coverage, litter and bare ground was examined, differences in species composition between contaminated and uncontaminated sites were assessed, and the ability to fix nitrogen, and form mycorrhiza, life form, pollination mode, seed dispersal and reproduction mode of each species was determined. Results showed less vegetation and litter cover in contaminated plots, and significantly higher soil carbon to nitrogen ratios. Species diversity was also lower on contaminated sites, although species richness was not significantly different. Self-pollinated species were significantly more common on contaminated sites. Five grasses and three forbs were identified as tolerant of hydrocarbon-contaminated soils, with two grasses -- Agropyron smithii, and Agropyron trachycaulum -- being the most promising for reclamation. The low vegetation cover on contaminated plots is attributed to high pH and carbon to nitrogen ratios, and low nitrogen and phosphorus that results from soil disturbance. High electrical conductivity is also considered to adversely affect vegetation and litter cover on contaminated sites. 54 refs., 3 tabs., 1 fig.

Survey of radioactive contamination for foodstuffs

International Nuclear Information System (INIS)

Lee, Wan No; Lee, Chang Wu; Choi, Geun Sik; Cho, Yeong Hyeon; Kang, Mun Ja; Cheong, Geun Ho; Kim, Hui Ryeong; Park, Du Won; Park, Hyo Guk; Kwak, Ji Yeon

2006-11-01

After the Chernobyl nuclear accident in 1986, a lot of countries including EU, Japan, USA are to strengthen survey of radioactive contamination for foodstuffs. Our country has also surveyed radioactive contamination of the imported foodstuffs and started to check continuously the radioactivity contamination of the open market foodstuffs since 2003. In this year, imported foodstuffs(130 samples) and domestic foodstuffs(10 samples) are analyzed to investigate the radioactive contamination. Sampled foodstuffs items are collected from the open markets; one group is the imported foodstuffs and the other group is the domestic foodstuffs producted around nuclear facilities and northeast of Sokcho city concerning recent situations. Samples are usually bought from traditional markets, mart, department store or the Internet. After pretreatments such as drying, ashing, and homogenization, all samples were analyzed by gamma spectrometer system for survey and assessment of radioactive contamination. The 131 I radionuclide isn't detected among all foodstuffs(imported and domestic). The 137 Cs radionuclide among the regulation radionuclides( 137 Cs, 13 4 C s, 131 I) of food code is only detected at the imported foodstuffs but its level is far below the maximum permitted level. For the improvement of measurement confidence, the developed analysis method is tested by the participation of the national and international intercomparison. The developed method based on test results and international standard would be used at radioactive analysis as well as an education of relative workers. It could be applied as the basis data for amending the analysis method of food code. It is technically supported for radioactive analysis of commercial company and the government including KFDA. Finally these results would be used to solve an ambiguous anxiety of a people for radiation exposure by foodstuffs intake and help the KFDA to manage systematically the radioactive contamination and to give

Air cleaning issues with contaminated sites

Energy Technology Data Exchange (ETDEWEB)

Bellamy, R.R. [Nuclear Regulatory Commission, King of Prussia, PA (United States)

1997-08-01

The US Nuclear Regulatory Commission has developed a list of contaminated sites that warrant special USNRC attention because they pose unique or complex decommissioning issues. This list of radiologically contaminated sites is termed the Site Decommissioning Management Plan (SDMP), and was first issued in 1990. A site is placed on the SDMP list if it has; (1) Problems with the viability of the responsible organization (e.g., the licensee for the site is unable or unwilling to pay for the decommissioning); (2) Large amounts of soil contamination or unused settling ponds or burial grounds that may make the waste difficult to dispose of; (3) The long-term presence of contaminated, unused buildings; (4) A previously terminated license; or (5) Contaminated or potential contamination of the ground water from on-site wastes. In deciding whether to add a site to the SDMP list, the NRC also considers the projected length of time for decommissioning and the willingness of the responsible organization to complete the decommissioning in a timely manner. Since the list was established, 9 sites have been removed from the list, and the current SDMP list contains 47 sites in 11 states. The USNRC annually publishes NUREG-1444, {open_quotes}Site Decommissioning Management Plan{close_quotes}, which updates the status of each site. This paper will discuss the philosophical goals of the SDMP, then will concentrate on the regulatory requirements associated with air cleaning issues at the SDMP sites during characterization and remediation. Both effluent and worker protection issues will be discussed. For effluents, the source terms at sites will be characterized, and measurement techniques will be presented. Off-site dose impacts will be included. For worker protection issues, air sampling analyses will be presented in order to show how the workers are adequately protected and their doses measured to satisfy regulatory criteria during decontamination operations. 1 tab.

Bioremediation of Petroleum Hydrocarbon Contaminated Sites

Energy Technology Data Exchange (ETDEWEB)

Fallgren, Paul

2009-03-30

Bioremediation has been widely applied in the restoration of petroleum hydrocarbon-contaminated. Parameters that may affect the rate and efficiency of biodegradation include temperature, moisture, salinity, nutrient availability, microbial species, and type and concentration of contaminants. Other factors can also affect the success of the bioremediation treatment of contaminants, such as climatic conditions, soil type, soil permeability, contaminant distribution and concentration, and drainage. Western Research Institute in conjunction with TechLink Environmental, Inc. and the U.S. Department of Energy conducted laboratory studies to evaluate major parameters that contribute to the bioremediation of petroleum-contaminated drill cuttings using land farming and to develop a biotreatment cell to expedite biodegradation of hydrocarbons. Physical characteristics such as soil texture, hydraulic conductivity, and water retention were determined for the petroleum hydrocarbon contaminated soil. Soil texture was determined to be loamy sand to sand, and high hydraulic conductivity and low water retention was observed. Temperature appeared to have the greatest influence on biodegradation rates where high temperatures (>50 C) favored biodegradation. High nitrogen content in the form of ammonium enhanced biodegradation as well did the presence of water near field water holding capacity. Urea was not a good source of nitrogen and has detrimental effects for bioremediation for this site soil. Artificial sea water had little effect on biodegradation rates, but biodegradation rates decreased after increasing the concentrations of salts. Biotreatment cell (biocell) tests demonstrated hydrocarbon biodegradation can be enhanced substantially when utilizing a leachate recirculation design where a 72% reduction of hydrocarbon concentration was observed with a 72-h period at a treatment temperature of 50 C. Overall, this study demonstrates the investigation of the effects of

Evaluation of decontamination during dismantling of plutonium-contaminated glove boxes

International Nuclear Information System (INIS)

Kinugasa, Manabu; Taguchi, Seigi; Ohzeki, Satoru; Inoue, Yoshiaki; Kashima, Sadamitsu

1981-01-01

The dismantling work of plutonium-contaminated glove boxes was carried out. These glove boxes had been used for the R and D of plutonium-uranium mixed oxide fuel for 15 years. The work was carried out in a pressure-controlled greenhouse, and the contamination of air in the greenhouse was monitored continuously. In order to reduce the contamination of air during dismantling, the decontamination and fixation of loose contaminants on the surfaces of glove boxes were very important. The correlation between decontamination and the contamination of air regarding dismantling is reported in this paper. The surface contamination density of the glove boxes was measured utilizing the smear method before and after the decontamination, and the decontamination effects were estimated. The contamination of air during dismantling was continuously measured with a plutonium dust monitor. It was found that loose contamination exponentially decreased by the decontamination process. When the so-called wet glove boxes, which contained wet recovery and waste disposal apparatus, were dismantled, the contamination of air did not exceed 500 (MPC) a. However, the contamination of air exceeded 500 (MPC) a several times in the present work of dismantling the so-called dry glove boxes which had been used for the fabrication of plutonium-uranium mixed oxide pellets. (Kato, T.)

Response of Soil Microbial Communities to Elevated Antimony and Arsenic Contamination Indicates the Relationship between the Innate Microbiota and Contaminant Fractions.

Science.gov (United States)

Sun, Weimin; Xiao, Enzong; Xiao, Tangfu; Krumins, Valdis; Wang, Qi; Häggblom, Max; Dong, Yiran; Tang, Song; Hu, Min; Li, Baoqin; Xia, Bingqing; Liu, Wei

2017-08-15

Mining of sulfide ore deposits containing metalloids, such as antimony and arsenic, has introduced serious soil contamination around the world, posing severe threats to food safety and human health. Hence, it is important to understand the behavior and composition of the microbial communities that control the mobilization or sequestration of these metal(loid)s. Here, we selected two sites in Southwest China with different levels of Sb and As contamination to study interactions among various Sb and As fractions and the soil microbiota, with a focus on the microbial response to metalloid contamination. Comprehensive geochemical analyses and 16S rRNA gene amplicon sequencing demonstrated distinct soil taxonomic inventories depending on Sb and As contamination levels. Stochastic gradient boosting indicated that citric acid extractable Sb(V) and As(V) contributed 5% and 15%, respectively, to influencing the community diversity. Random forest predicted that low concentrations of Sb(V) and As(V) could enhance the community diversity but generally, the Sb and As contamination impairs microbial diversity. Co-occurrence network analysis indicated a strong correlation between the indigenous microbial communities and various Sb and As fractions. A number of taxa were identified as core genera due to their elevated abundances and positive correlation with contaminant fractions (total Sb and As concentrations, bioavailable Sb and As extractable fractions, and Sb and As redox species). Shotgun metagenomics indicated that Sb and As biogeochemical redox reactions may exist in contaminated soils. All these observations suggest the potential for bioremediation of Sb- and As-contaminated soils.

Status of contamination monitoring in Bangladesh

Energy Technology Data Exchange (ETDEWEB)

Begum, Aleya [Institute of Nuclear Science and Technology, Savar, Dacca (Bangladesh)

1997-06-01

The applications of radioisotopes and radiation sources to the research and development in medicine, food agriculture, industries and others are rapidly increasing in Bangladesh. The existing major nuclear facilites and allied laboratories of the country include 3 MW TRIGA Mark-2 research reactor for training, research and radioisotope production, 14 MeV neutron generator for nuclear data measurement and elemental analysis via neutron activation, 3 MeV Van de Graaff accelerator for the research and application of nuclear physics, and 50,000 Ci and 5,000 Ci Co-60 irradiators. About 10 Co-60 and Cs-137 teletherapy units are in operation in hospitals. The radioactive contamination of working areas, equipment, protective clothing and skin may result from normal operation and accidents, and contamination monitoring and decontamination are the essential part of radiation protection program. Surface contamination is monitored with Berthold survey meters. Hand and foot monitors have been used. Routine systematic search, continuous air monitoring, the examination of silt movement in Chittagong harbor using Sc-46 tracer and the measurement of tritium contamination for the neutron generator are reported. (K.I.)

Bag-like contaminant control work module

International Nuclear Information System (INIS)

Buchanan, H.; Jacobson, E.B.

1982-01-01

A bag-like contaminant control work module is formed from a flexible impervious membrane which is inflated inside of an enclosed workspace to protect workers in the module from contaminants. The workspace, such as in a nuclear power steam generator, has a portal or manway opening into the workspace into which the module is secured by a module passageway. The module includes one or more glove boxes, in which the workers perform their assigned tasks after passing through the passageway and portal. The module includes one or more absolute filters allowing passage of air flow through the module passageway and into the workspace only through the filters. The module may include an auxiliary passageway secured to the outside of the module passageway and also secured in the portal opening and through which items can be passed back and forth to the worker in the glove box from outside the portal. The module is invertible so that it can be pulled out of the workspace trapping all the contaminants therein and disposed of without handling the contaminants

Risk assessment of soil contamination criteria

International Nuclear Information System (INIS)

King, C.M.; Marter, W.L.; Montaque, D.F.; Holton, G.A.

1987-06-01

Criteria have been developed to select radioactive and nonradioactive contaminants at waste sites detailed analysis and risk assessment. These criteria were based on soil and water quality guidelines developed by various government agencies to determine if the criteria were appropriate. We performed a risk assessment of a hypothetical site which contained radioactive and nonradioactive contaminants at levels equal to the criteria values. Risks to the public from atmospheric, surface water, and groundwater exposure pathways were examined. Health risks to the public from atmospheric releases of radioactive and nonradioactive materials from a waste at soil criteria contamination levels are low. Health risks to the maximally exposed individual to chemical carcinogens are considerably below traditional EPA action levels. And health risks to the maximally exposed individual to atmospherically released radioactive contaminants is 1.88 x 10 -7 , more than a factor of 5 less than 10 -6 . Based on our atmospheric exposure pathways analysis and risk assessment, the applied soil criteria are appropriate for screening out unimportant risk contributors to human health from atmospheric exposure pathways. 13 refs., 3 figs., 7 tabs

Radioactive contamination of recycled metals

International Nuclear Information System (INIS)

Lubenau, J.O.; Cool, D.A.; Yusko, J.G.

1996-01-01

Radioactive sources commingled with metal scrap have become a major problem for the metals recycling industry worldwide. Worldwide there have been 38 confirmed reports of radioactive sources accidentally smelted with recycled metal. In some instances, contaminated metal products were subsequently distributed. The metal mills, their products and byproducts from the metal making process such as slags, crosses and dusts from furnaces can become contaminated. In the U.S., imported ferrous metal products such as reinforcement bars, pipe flanges, table legs and fencing components have been found contaminated with taco. U.S. steel mills have unintentionally smelted radioactive sources on 16 occasions. The resulting cost for decontamination waste disposal and temporary closure of the steel mill is typically USD 10,000,000 and has been as much as USD 23,000,000. Other metal recycling industries that have been affected by this problem include aluminum, copper, zinc, gold, lead and vanadium. (author)

UNDERWATER COATINGS FOR CONTAMINATION CONTROL

International Nuclear Information System (INIS)

Julia L. Tripp; Kip Archibald; Ann Marie Phillips; Joseph Campbell

2004-01-01

The Idaho National Laboratory (INL) deactivated several aging nuclear fuel storage basins. Planners for this effort were greatly concerned that radioactive contamination present on the basin walls could become airborne as the sides of the basins became exposed during deactivation and allowed to dry after water removal. One way to control this airborne contamination was to fix the contamination in place while the pool walls were still submerged. There are many underwater coatings available on the market for marine, naval and other applications. A series of tests were run to determine whether the candidate underwater fixatives were easily applied and adhered well to the substrates (pool wall materials) found in INL fuel pools. Lab-scale experiments were conducted by applying fourteen different commercial underwater coatings to four substrate materials representative of the storage basin construction materials, and evaluating their performance. The coupons included bare concrete, epoxy painted concrete, epoxy painted carbon steel, and stainless steel. The evaluation criteria included ease of application, adherence to the four surfaces of interest, no change on water clarity or chemistry, non-hazardous in final applied form and be proven in underwater applications. A proprietary two-part, underwater epoxy owned by S. G. Pinney and Associates was selected from the underwater coatings tested for application to all four pools. Divers scrubbed loose contamination off the basin walls and floors using a ship hull scrubber and vacuumed up the sludge. The divers then applied the coating using a special powered roller with two separate heated hoses that allowed the epoxy to mix at the roller surface was used to eliminate pot time concerns. The walls were successfully coated and water was removed from the pools with no detectable airborne contamination releases

Radioactive contamination of aquatic media and organisms; La contamination radioactive des milieux et des organismes aquatiques

Energy Technology Data Exchange (ETDEWEB)

Fontaine, Y [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

1960-07-01

After a brief account of the radioactive wastes produced by peaceful or military uses of Atomic Industry, the author first describes a series of observations carried out 'in the field' on the extent of contamination in aquatic organisms with respect to that of the medium. The experimental studies are then analysed, with reference both to the radioisotope metabolism and to the factors and types of contamination of aquatic organisms by wastes from atomic industry. A precise experimental project is presented at the end of the paper, including almost 300 references. (author) [French] Apres une courte etude des dechets radioactifs produits par les utilisations pacifiques ou militaires de l'Industrie Atomique, l'auteur fait etat d'abord des observations effectuees 'sur le terrain' concernant l'extension de la contamination des organismes aquatiques en rapport avec celle du milieu. L'auteur analyse ensuite les etudes experimentales se rapportant aussi bien au metabolisme des radioisotopes qu'aux facteurs et aux modalites de la contamination des organismes aquatiques par les dechets de l'industrie atomique. Un projet de travail experimental precis est presente a la fin de cette revue qui comporte pres de 300 references bibliographiques. (auteur)

Assessment of sediment contamination in Casco Bay, Maine, USA

Energy Technology Data Exchange (ETDEWEB)

Wade, Terry L. [Geochemical and Environmental Research Group, Texas A and M University, 833 Graham Road, College Station, TX 77845 (United States); Sweet, Stephen T. [Geochemical and Environmental Research Group, Texas A and M University, 833 Graham Road, College Station, TX 77845 (United States)], E-mail: sweet@gerg.tamu.edu; Klein, Andrew G. [Geography Department, Texas A and M University, 814B Eller O and M Building, College Station, TX 77843 (United States)

2008-04-15

The current status of contaminant concentrations in Casco Bay, decadal trends of these contaminants and changes in their geographical distribution are assessed using sediment samples collected approximately 10 years apart. In general, regulated contaminants appeared to be decreasing in concentration. Total PAH and dioxins/furans concentrations did not significantly change over this period. Total organochlorine pesticides, 4,4-DDE, 4,4-DDD, total DDT, PCB, tributyltin and total butyltin decreased in concentration. Trace element concentrations in sediments decreased at the majority of the sampling sites for chromium, nickel, and selenium while arsenic, cadmium, copper, lead, mercury, silver, and zinc remained relatively constant. None of the contaminants measured has increased by more than a factor of 2. Selected sites located in the Inner Bay, where concentrations are higher and new inputs were more likely, showed increased concentrations of contaminants. Most contaminants were not found at concentrations expected to adversely affect sediment biota based on ERL/ERM guidelines. - Sediment studies indicate decadal decreases for many chemical contaminants in Casco Bay.

Assessment of sediment contamination in Casco Bay, Maine, USA

International Nuclear Information System (INIS)

Wade, Terry L.; Sweet, Stephen T.; Klein, Andrew G.

2008-01-01

The current status of contaminant concentrations in Casco Bay, decadal trends of these contaminants and changes in their geographical distribution are assessed using sediment samples collected approximately 10 years apart. In general, regulated contaminants appeared to be decreasing in concentration. Total PAH and dioxins/furans concentrations did not significantly change over this period. Total organochlorine pesticides, 4,4-DDE, 4,4-DDD, total DDT, PCB, tributyltin and total butyltin decreased in concentration. Trace element concentrations in sediments decreased at the majority of the sampling sites for chromium, nickel, and selenium while arsenic, cadmium, copper, lead, mercury, silver, and zinc remained relatively constant. None of the contaminants measured has increased by more than a factor of 2. Selected sites located in the Inner Bay, where concentrations are higher and new inputs were more likely, showed increased concentrations of contaminants. Most contaminants were not found at concentrations expected to adversely affect sediment biota based on ERL/ERM guidelines. - Sediment studies indicate decadal decreases for many chemical contaminants in Casco Bay

Biogeochemical and engineered barriers for preventing spread of contaminants.

Science.gov (United States)

Baltrėnaitė, Edita; Lietuvninkas, Arvydas; Baltrėnas, Pranas

2018-02-01

The intensive industrial development and urbanization, as well as the negligible return of hazardous components to the deeper layers of the Earth, increases the contamination load on the noosphere (i.e., the new status of the biosphere, the development of which is mainly controlled by the conscious activity of a human being). The need for reducing the spread and mobility of contaminants is growing. The insights into the role of the tree in the reduction of contaminant mobility through its life cycle are presented to show an important function performed by the living matter and its products in reducing contamination. For maintaining the sustainable development, natural materials are often used as the media in the environmental protection technologies. However, due to increasing contamination intensity, the capacity of natural materials is not sufficiently high. Therefore, the popularity of engineered materials, such as biochar which is the thermochemically modified lignocellulosic product, is growing. The new approaches, based on using the contaminant footprint, as well as natural (biogeochemical) and engineered barriers for reducing contaminant migration and their application, are described in the paper.

Analysis of soils contaminated with petroleum constituents

International Nuclear Information System (INIS)

O'Shay, T.A.; Hoddinott, K.

1994-01-01

This symposium was held in Atlanta, Georgia on June 24, 1993. The purpose of the symposium was to provide a forum for exchange of information on petroleum contaminated soils. When spilled on the ground, petroleum products can cause massive problems in the environment. In this Special Technical Publication (STP), papers were selected in two categories; the analytical procedures for soil contaminated with petroleum hydrocarbons and the behavior of hydrocarbon contaminated soils. Individual papers have been processed separately for inclusion in the appropriate data bases

30 CFR 57.5005 - Control of exposure to airborne contaminants.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Control of exposure to airborne contaminants... Underground § 57.5005 Control of exposure to airborne contaminants. Control of employee exposure to harmful airborne contaminants shall be, insofar as feasible, by prevention of contamination, removal by exhaust...

Removal of residual contaminants in petroleum-contaminated soil by Fenton-like oxidation

Energy Technology Data Exchange (ETDEWEB)

Lu Mang [School of Material Science and Engineering, Jingdezhen Ceramic Institute, Jingdezhen, 333001, Jiangxi Province (China); State Key Laboratory of Heavy Oil Processing, China University of Petroleum, Beijing 102249 (China); Zhang Zhongzhi, E-mail: zzzhang1955@hotmail.com [State Key Laboratory of Heavy Oil Processing, China University of Petroleum, Beijing 102249 (China); Qiao Wei; Guan Yueming; Xiao Meng; Peng Chong [State Key Laboratory of Heavy Oil Processing, China University of Petroleum, Beijing 102249 (China)

2010-07-15

The degradation of bioremediation residues by hydrogen peroxide in petroleum-contaminated soil was investigated at circumneutral pH using a Fenton-like reagent (ferric ion chelated with EDTA). Batch tests were done on 20 g soil suspended in 60 mL aqueous solution containing hydrogen peroxide and Fe{sup 3+}-EDTA complex under constant stirring. A slurry reactor was used to treat the soil based on the optimal reactant conditions. Contaminants were characterized by Fourier transform infrared spectroscopy and Fourier transform ion cyclotron resonance mass spectrometry. The results showed that the optimal treatment condition was: the molar ratio of hydrogen peroxide to iron = 200:1, and pH 7.0. Under the optimum condition, total dichloromethane-extractable organics were reduced from 14,800 to 2300 mg kg{sup -1} soil when the accumulative H{sub 2}O{sub 2} dosage was 2.45 mol kg{sup -1} soil during the reactor treatment. Abundance of viable cells was lower in incubated Fenton-like treated soil than in untreated soil. Oxidation of contaminants produced remarkable compositional and structural modifications. A fused ring compound, identified as C{sub 34}H{sub 38}N{sub 1}, was found to exhibit the greatest resistance to oxidation.

Contaminant bioavailability in soils, sediments, and aquatic environments

OpenAIRE

Traina, Samuel J.; Laperche, Valérie

1999-01-01

The aqueous concentrations of heavy metals in soils, sediments, and aquatic environments frequently are controlled by the dissolution and precipitation of discrete mineral phases. Contaminant uptake by organisms as well as contaminant transport in natural systems typically occurs through the solution phase. Thus, the thermodynamic solubility of contaminant-containing minerals in these environments can directly influence the chemical reactivity, transport, and ecotoxici...

Cleanup procedures at the Nevada Test Site and at other radioactively contaminated sites including representative costs of cleanup and treatment of contaminated areas

International Nuclear Information System (INIS)

Talmage, S.S.; Chilton, B.D.

1987-09-01

This review summarizes available information on cleanup procedures at the Nevada Test Site and at other radioactively contaminated sites. Radionuclide distribution and inventory, size of the contaminated areas, equipment, and cleanup procedures and results are included. Information about the cost of cleanup and treatment for contaminated land is presented. Selected measures that could be useful in estimating the costs of cleaning up radioactively contaminated areas are described. 76 refs., 16 tabs

Payload/orbiter contamination control requirement study: Preliminary contamination mission support plan. [a management analysis of project planning of spacecraft sterilization

Science.gov (United States)

Bareiss, L. E.; Hooper, V. W.; Ress, E. B.

1976-01-01

Progress is reported on the mission support plan and those support activities envisioned to be applicable and necessary during premission and postmission phases of the Spacelab program. The purpose, role, and requirements of the contamination control operations for the first two missions of the Spacelab equipped Space Transportation System are discussed. The organization of the contamination control operation and its relationship to and interfaces with other mission support functions is also discussed. Some specific areas of contamination to be investigated are treated. They are: (1) windows and viewports, (2) experiment equipment, (3) thermal control surfaces, (4) the contaminant induced atmosphere (as differentiated from the normal ambient atmosphere at the orbit altitude), and (5) optical navigation instruments.

Bioremediation of Polycyclic Aromatic Hydrocarbon contaminated ...

African Journals Online (AJOL)

This study investigates the effect of lead and chromium on the rate of bioremediation of polycyclic aromatic hydrocarbon (PAH) contaminated clay soil. Naphthalene was used as a target PAH. The soil was sterilized by heating at 120oC for one hour. 100g of the soil was contaminated with lead, chromium, nickel and mercury ...

Impact of inorganic contaminants on microalgae productivity and bioremediation potential.

Science.gov (United States)

Torres, Eric M; Hess, Derek; McNeil, Brian T; Guy, Tessa; Quinn, Jason C

2017-05-01

As underdeveloped nations continue to industrialize and world population continues to increase, the need for energy, natural resources, and goods will lead to ever increasing inorganic contaminants, such as heavy metals, in various waste streams that can have damaging effects on plant life, wildlife, and human health. This work is focused on the evaluation of the potential of Nannochloropsis salina to be integrated with contaminated water sources for the concurrent production of a biofuel feedstock while providing an environmental service through bioremediation. Individual contaminants (As, Cd, Cr, Co, Cu, Pb, Ni, Hg, Se, and Zn) at various concentrations ranging from a low concentration (1X) to higher concentrations (10X, and 40X) found in contaminated systems (mine tailings, wastewater treatment plants, produced water) were introduced into growth media. Biological growth experimentation was performed in triplicate at the various contaminant concentrations and at 3 different light intensities. Results show that baseline concentrations of each contaminant slightly decreased biomass growth to between 89% and 99% of the control with the exception of Ni which dramatically reduced growth. Increased contaminant concentrations resulted in progressively lower growth rates for all contaminants tested. Lipid analysis shows most baseline contaminant concentrations slightly decrease or have minimal effects on lipid content at all light levels. Trace contaminant analysis on the biomass showed Cd, Co, Cu, Pb, and Zn were sorbed by the microalgae with minimal contaminants remaining in the growth media illustrating the effectiveness of microalgae to bioremediate these contaminants when levels are sufficiently low to not detrimentally impact productivity. The microalgae biomass was less efficient at sorption of As, Cr, Ni, and Se. Copyright © 2017 Elsevier Inc. All rights reserved.

Developing an integration tool for soil contamination assessment

Science.gov (United States)

Anaya-Romero, Maria; Zingg, Felix; Pérez-Álvarez, José Miguel; Madejón, Paula; Kotb Abd-Elmabod, Sameh

2015-04-01

In the last decades, huge soil areas have been negatively influenced or altered in multiples forms. Soils and, consequently, underground water, have been contaminated by accumulation of contaminants from agricultural activities (fertilizers and pesticides) industrial activities (harmful material dumping, sludge, flying ashes) and urban activities (hydrocarbon, metals from vehicle traffic, urban waste dumping). In the framework of the RECARE project, local partners across Europe are focusing on a wide range of soil threats, as soil contamination, and aiming to develop effective prevention, remediation and restoration measures by designing and applying targeted land management strategies (van Lynden et al., 2013). In this context, the Guadiamar Green Corridor (Southern Spain) was used as a case study, aiming to obtain soil data and new information in order to assess soil contamination. The main threat in the Guadiamar valley is soil contamination after a mine spill occurred on April 1998. About four hm3 of acid waters and two hm3 of mud, rich in heavy metals, were released into the Agrio and Guadiamar rivers affecting more than 4,600 ha of agricultural and pasture land. Main trace elements contaminating soil and water were As, Cd, Cu, Pb, Tl and Zn. The objective of the present research is to develop informatics tools that integrate soil database, models and interactive platforms for soil contamination assessment. Preliminary results were obtained related to the compilation of harmonized databases including geographical, hydro-meteorological, soil and socio-economic variables based on spatial analysis and stakeholder's consultation. Further research will be modellization and upscaling at the European level, in order to obtain a scientifically-technical predictive tool for the assessment of soil contamination.

Mercury contamination of the Belgian avifauna 1970-1981

Energy Technology Data Exchange (ETDEWEB)

Delbeke, K.; Joiris, C.; Decadt, G.

1984-01-01

Two hundred birds found dead in Belgium between 1970 and 1981, and belonging to 30 species, were analyzed for total mercury contamination. The contamination of aquatic birds ranged between 0.11 and 35 ..mu..g g/sup -1/ wet weight. For terrestrial birds, the extreme values were not detectable and 14 ..mu..g g/sup -1/. In both cases, differences in diet can explain the differences in contamination. The order of diets associated with increasing mercury contamination for aquatic birds was invertebrates, zooplankton and garbage, and fish; and for terrestrial birds this consisted of plants, invertebrates, mammals and birds. For raptors and owls, this effect of diet includes geographical variations within species. A higher mercury contamination level in the winter and early spring was noted for two species of owls. For aquatic birds, the contamination of liver was higher than that of kidney, with ratios varying between 1.2 and 2.5. For terrestrial birds, the ratio was closer to 1. A few determinations were also made for muscle and heart, giving respectively 0.25 and 0.6 of the liver contamination. Among the birds analyzed for their liver contamination, 15% showed levels higher than 3 ..mu..g g/sup -1/ and could have been affected in their reproduction; 3% had levels higher than 10 ..mu..g g/sup -1/, and could have died from mercury poisoning; and 6% showed an abnormally high liver:kidney ratio, which could reflect an acute intoxication. There exists a striking parallelism between the levels of mercury and of organochlorine residues (DDT) in birds of prey, suggesting the existence of common ecotoxicological mechanisms.

Spacecraft contamination programs within the Air Force Systems Command Laboratories

Science.gov (United States)

Murad, Edmond

1990-01-01

Spacecraft contamination programs exist in five independent AFSC organizations: Geophysics Laboratory (GL), Arnold Engineering and Development Center (AEDC), Rome Air Development Center (RADC/OSCE), Wright Research and Development Center (MLBT), Armament Laboratory (ATL/SAI), and Space Systems Division (SSD/OL-AW). In addition, a sizable program exists at Aerospace Corp. These programs are complementary, each effort addressing a specific area of expertise: GL's effort is aimed at addressing the effects of on-orbit contamination; AEDC's effort is aimed at ground simulation and measurement of optical contamination; RADC's effort addresses the accumulation, measurement, and removal of contamination on large optics; MLBT's effort is aimed at understanding the effect of contamination on materials; ATL's effort is aimed at understanding the effect of plume contamination on systems; SSD's effort is confined to the integration of some contamination experiments sponsored by SSD/CLT; and Aerospace Corp.'s effort is aimed at supporting the needs of the using System Program Offices (SPO) in specific areas, such as contamination during ground handling, ascent phase, laboratory measurements aimed at understanding on-orbit contamination, and mass loss and mass gain in on-orbit operations. These programs are described in some detail, with emphasis on GL's program.

Woody biomass phytoremediation of contaminated brownfield land

Energy Technology Data Exchange (ETDEWEB)

French, Christopher J. [School of Biological and Earth Sciences, Liverpool John Moores University, Byrom Street, Liverpool L3 3AF (United Kingdom); Dickinson, Nicholas M. [School of Biological and Earth Sciences, Liverpool John Moores University, Byrom Street, Liverpool L3 3AF (United Kingdom)]. E-mail: n.m.dickinson@livjm.ac.uk; Putwain, Philip D. [Ecological Restoration Consultants (ERC), Ness Botanic Gardens, University of Liverpool, Ness, Cheshire CH64 (United Kingdom)

2006-06-15

Economic and environmental regeneration of post-industrial landscapes frequently involves some element of re-afforestation or tree planting. We report field trials that evaluate whether woody biomass production is compatible with managing residual trace element contamination in brownfield soils. Large-scale mapping of contamination showed a heterogenous dispersion of metals and arsenic, and highly localised within-site hotspots. Yields of Salix, Populus and Alnus were economically viable, showing that short-rotation coppice has a potentially valuable role in community forestry. Mass balance modelling demonstrated that phytoextraction potentially could reduce contamination hotspots of more mobile elements (Cd and Zn) within a 25-30-year life cycle of the crops. Cd and Zn in stems and foliage of Salix were 4-13 times higher than EDTA-extractable soil concentrations. Lability of other trace elements (As, Pb, Cu, Ni) was not increased 3 years after planting the coppice; woody biomass may provide an effective reduction of exposure (phytostabilisation) to these less mobile contaminants. - Field trials show short-rotation coppice provides effective risk management and remediation solutions to hotspots of residual metal and As contamination of brownfield land.

Woody biomass phytoremediation of contaminated brownfield land

International Nuclear Information System (INIS)

French, Christopher J.; Dickinson, Nicholas M.; Putwain, Philip D.

2006-01-01

Economic and environmental regeneration of post-industrial landscapes frequently involves some element of re-afforestation or tree planting. We report field trials that evaluate whether woody biomass production is compatible with managing residual trace element contamination in brownfield soils. Large-scale mapping of contamination showed a heterogenous dispersion of metals and arsenic, and highly localised within-site hotspots. Yields of Salix, Populus and Alnus were economically viable, showing that short-rotation coppice has a potentially valuable role in community forestry. Mass balance modelling demonstrated that phytoextraction potentially could reduce contamination hotspots of more mobile elements (Cd and Zn) within a 25-30-year life cycle of the crops. Cd and Zn in stems and foliage of Salix were 4-13 times higher than EDTA-extractable soil concentrations. Lability of other trace elements (As, Pb, Cu, Ni) was not increased 3 years after planting the coppice; woody biomass may provide an effective reduction of exposure (phytostabilisation) to these less mobile contaminants. - Field trials show short-rotation coppice provides effective risk management and remediation solutions to hotspots of residual metal and As contamination of brownfield land

Remedial action of radium contaminated residential properties

International Nuclear Information System (INIS)

White, D.; Eng, J.

1986-01-01

Since November 1983, the New Jersey Department of Environmental Protection (NJDEP) and the US Environmental Protection Agency (USEPA) have been in the process of identifying properties in Montclair, Glen Ridge and West Orange, New Jersey, which were built over radium contaminated soil landfilled areas. Elevated indoor radon concentrations prompted the Centers for Disease Control (CDC) to issue a health advisory which included permanent remediation of radon progeny levels in excess of 0.02 Working Levels within two years of discovery. In order to expedite remedial action, NJDEP undertook a ten million dollar cleanup program. Remedial Action at the 12 residential properties encountered some unanticipated problems despite the efforts of numerous government agencies and their contractors to characterize the contamination as much as possible prior to remediation. Some of the unanticipated issues include contamination from other radionuclides, underestimation of removal volumes, and controversy over the transportation and disposal of the radium contaminated soil at a commercial facility in Nevada. This paper will review the approach taken by NJDEP to the remedial action for radium contaminated soil, discuss some of the issues encountered during the remedial action, and provide post remedial action data

Contamination of the Arctic by exotic air toxics

International Nuclear Information System (INIS)

Ford, J.; Landers, D.

1991-01-01

Various kinds of atmospheric pollutants are commonly known to occur in arctic environments. These include organic contaminants, pollutants associated with fossil fuel combustion, smelting, industrial development, and radionuclides. Recently, additional concern has arisen from studies suggesting that at least some atmospheric contaminants may be susceptible to poleward redistribution as a result of their physical and chemical properties. Thus, contamination of the arctic may be exacerbated by the tendency of selected contaminants produced at lower latitudes to be transported to polar regions and incorporated into high latitude food chains. Although awareness of exotic contaminants in high latitude food chains is not new, regional baseline data are needed to document the spatial extent and magnitude of this potentially serious problem. The US Arctic is little studied in this regard relative to several other circumpolar nations (e.g., Canada, Sweden); over the next year the authors will be designing a regional survey to begin remedying this information gap. A major focus of this activity will be to ensure compatibility with both ongoing international studies of arctic contamination, and the USEPA Environmental Monitoring and Assessment Program. Issues related to sampling design will be outlined and discussed

Detection of microbial contamination in platelets

Science.gov (United States)

Berg, Tracy L.; Leparc, German; Huffman, Debra E.; Gennaccaro, Angela L.; Garcia-Lopez, Alicia; Klungness, Greta; Stephans, Christie; Garcia-Rubio, Luis H.

2005-03-01

In the United States, approximately 100 patients develop fatal sepsis associated with platelet transfusions every year. Current culture methods take 24-48 hours to acquire results, which in turn decrease the shelf life of platelets. Many of the microorganisms that contaminate platelets can replicate easily at room temperature, which is the necessary storage temperature to keep platelets functional. Therefore, there is a need for in-situ quality control assessment of the platelet quality. For this purpose, a real time spectrophotometric technique has been developed. The Spectral Acquisition Processing Detection (SAPD) method, comprised of a UV-vis spectrophotometer and modeling algorithms, is a rapid method that can be performed prior to platelet transfusion to decrease the risk of bacterial infection to patients. The SAPD method has been used to determine changes in cell suspensions, based on size, shape, chemical composition and internal structure. Changes in these cell characteristics can in turn be used to determine microbial contamination, platelet aging and other physiologic changes. Detection limits of this method for platelet suspensions seeded with bacterial contaminants were identified to be less than 100 cfu/ml of sample. Bacterial counts below 1000 cfu/ml are not considered clinically significant. The SAPD method can provide real-time identification of bacterial contamination of platelets affording patients an increased level of safety without causing undue strain on laboratory budgets or personnel while increasing the time frame that platelets can be used by dramatically shortening contaminant detection time.

Hydrogen peroxide treatment of TCE contaminated soil

International Nuclear Information System (INIS)

Hurst, D.H.; Robinson, K.G.; Siegrist, R.L.

1993-01-01

Solvent contaminated soils are ubiquitous in the industrial world and represent a significant environmental hazard due to their persistence and potentially negative impacts on human health and the environment. Environmental regulations favor treatment of soils with options which reduce the volume and toxicity of contaminants in place. One such treatment option is the in-situ application of hydrogen peroxide to soils contaminated with chlorinated solvents such as trichloroethylene (TCE). This study investigated hydrogen peroxide mass loading rates on removal of TCE from soils of varying organic matter content. Batch experiments conducted on contaminated loam samples using GC headspace analysis showed up to 80% TCE removal upon peroxide treatment. Column experiments conducted on sandy loam soils with high organic matter content showed only 25% TCE removal, even at hydrogen peroxide additions of 25 g peroxide per kg soil

Contamination monitoring: an overview and its objectives

International Nuclear Information System (INIS)

Mangena, S.

2013-04-01

The study presents and objectively summarises the aspect of contamination monitoring. This envisages reviewing sources of contamination and evaluating the scientific basis for practice specific courses of action for rehabilitation in a bid to restore pristine conditions wherever possible. The practices considered include nuclear medicine, reprocessing plants, fuel production plants, uranium and thorium mining and milling together with near surface disposal facilities (for radioactive waste). It also deals with monitoring sites contaminated as a consequence of past practices. General issues related to the design and operation of monitoring systems during and in the aftermath of a nuclear or radiological accident are also discussed including monitoring for long lived radionuclides widely dispersed in the environment following an accidental release. Thus the above discourse provides a framework for both quantitative and qualitative measures undertaken to enable effective response in the event of radioactive contamination. (au)

Variable pattern contamination control under positive pressure

International Nuclear Information System (INIS)

Philippi, H.M.

1997-01-01

Airborne contamination control in nuclear and biological laboratories is traditionally achieved by directing the space ventilation air at subatmospheric pressures in one fixed flow pattern. However, biological and nuclear contamination flow control in the new Biological Research Facility, to be commissioned at the Chalk River Laboratories in 1996, will have the flexibility to institute a number of contamination control patterns, all achieved at positive (above atmospheric) pressures. This flexibility feature, made possible by means of a digitally controlled ventilation system, changes the facility ventilation system from being a relatively rigid building service operated by plant personnel into a flexible building service which can be operated by the facility research personnel. This paper focuses on and describes the application of these unique contamination control features in the design of the new Biological Research Facility. 3 refs., 7 figs

Variable pattern contamination control under positive pressure

Energy Technology Data Exchange (ETDEWEB)

Philippi, H.M. [Chalk River Labs., Ontario (Canada)

1997-08-01

Airborne contamination control in nuclear and biological laboratories is traditionally achieved by directing the space ventilation air at subatmospheric pressures in one fixed flow pattern. However, biological and nuclear contamination flow control in the new Biological Research Facility, to be commissioned at the Chalk River Laboratories in 1996, will have the flexibility to institute a number of contamination control patterns, all achieved at positive (above atmospheric) pressures. This flexibility feature, made possible by means of a digitally controlled ventilation system, changes the facility ventilation system from being a relatively rigid building service operated by plant personnel into a flexible building service which can be operated by the facility research personnel. This paper focuses on and describes the application of these unique contamination control features in the design of the new Biological Research Facility. 3 refs., 7 figs.

Materials SIG quantification and characterization of surface contaminants

Science.gov (United States)

Crutcher, E. Russ

1992-01-01

When LDEF entered orbit its cleanliness was approximately a MIL-STD-1246B Level 2000C. Its burden of contaminants included particles from every part of its history including a relatively small contribution from the shuttle bay itself. Although this satellite was far from what is normally considered clean in the aerospace industry, contaminating events in orbit and from processing after recovery were easily detected. The molecular contaminants carried into orbit were dwarfed by the heavy deposition of UV polymerized films from outgassing urethane paints and silicone based materials. Impacts by relatively small objects in orbit could create particulate contaminants that easily dominated the particle counts within a centimeter of the impact site. During the recovery activities LDEF was 'sprayed' with a liquid high in organics and water soluble salts. With reentry turbulence, vibration, and gravitational loading particulate contaminants were redistributed about LDEF and the shuttle bay.

Optimization of the control of contamination at nuclear power plants

International Nuclear Information System (INIS)

Khan, T.A.; Baum, J.W.

1988-05-01

A methodology is described for the optimization of the actions taken to control contamination. It deals with many aspects of contamination, such as the monetary value assigned to a unit of radiation dose, the treatment of skin and extremity dose, and the inefficiencies introduced from working in a contaminated environemnt. The optimization method is illustrated with two case studies based on cleanup projects at nuclear power plants. Guidelines for the use of protective apparel, and for monitoring radiation and contamination at various levels of contamination are presented. The report concludes that additional research is required to quantify the effect of a contaminated environment on work efficiencies

Tracking the origin and dispersion of contaminated sediments transported by rivers draining the Fukushima radioactive contaminant plume

Directory of Open Access Journals (Sweden)

H. Lepage

2015-03-01

Full Text Available This study was conducted in several catchments draining the main Fukushima Dai-ichi Power Plant contaminant plume in Fukushima prefecture, Japan. We collected soils and sediment drape deposits (n = 128 and investigated the variation in 137Cs enrichment during five sampling campaigns, conducted every six months, which typically occurred after intense erosive events such as typhoons and snowmelt. We show that upstream contaminated soils are eroded during summer typhoons (June–October before being exported during the spring snowmelt (March–April. However, this seasonal cycle of sediment dispersion is further complicated by the occurrence of dam releases that may discharge large amounts of contaminants to the coastal plains during the coming years.

Spectral imaging for contamination detection in food

DEFF Research Database (Denmark)

Carstensen, Jens Michael

application of the technique is finding anomalies I supposedly homogeneous matter or homogeneous mixtures. This application occurs frequently in the food industry when different types of contamination are to be detected. Contaminants could be e.g. foreign matter, process-induced toxins, and microbiological...... spoilage. Many of these contaminants may be detected in the wavelength range visible to normal silicium-based camera sensors i.e. 350-1050 nm with proper care during sample preparation, sample presentation, image acquisition and analysis. This presentation will give an introduction to the techniques behind...

Ex-situ bioremediation of petroleum contaminated soil

International Nuclear Information System (INIS)

Minier, M.R.

1994-01-01

The use of stress acclimated bacteria and nutrient supplements to enhance the biodegradation of petroleum contaminated soil can be a cost effective and reliable treatment technology to reduce organic contaminant levels to below established by local, state, and federal regulatory clean-up criteria. This paper will summarize the results of a field study in which 12,000 yds 3 of petroleum contaminated soil was successfully treated via ex-situ bioremediation and through management of macro and micronutrient concentrations, as well as, other site specific environmental factors that are essential for optimizing microbial growth

40 CFR 141.13 - Maximum contaminant levels for turbidity.

Science.gov (United States)

2010-07-01

... turbidity. 141.13 Section 141.13 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) WATER... Maximum contaminant levels for turbidity. The maximum contaminant levels for turbidity are applicable to... part. The maximum contaminant levels for turbidity in drinking water, measured at a representative...

Materials contamination control in the microelectronic industry

International Nuclear Information System (INIS)

Tardif, F.

1993-01-01

This paper deals with many aspects of the contamination of materials in the microelectronic industry. The contamination's control of chemicals, process gases, silicon and the survey of the ions free water's purity are treated. (TEC). 29 figs., 7 tabs

Plutonium-contaminated fragments at the Taranaki site at Maralinga

International Nuclear Information System (INIS)

Burns, P.A.; Cooper, M.B.; Duggleby, J.C.; Mika, J.F.; Williams, G.A.

1986-07-01

A detailed assessment is presented of the distribution of plutonium-contaminated fragments and sub-millimetre particles in the vicinity of the Taranaki site at the former U.K. Atomic Weapons Test Range at Maralinga in South Australia. The area which is contaminated with fragments has been divided into three general regions with the designations 'heavily contaminated', 'moderately contaminated' and 'plumes'. The average surface density, activity and estimated total number of fragments are presented for each region. Average surface densities of all fragments with americium-241 activities greater than 2 kBq are estimated to be 33, 7 and 2 m -2 for the 'heavily contaminated', 'moderately contaminated' and 'plumes' regions respectively. The total number of such fragments is estimated to be in excess of three million which accounts for a total plutonium activity of approximately 0.8 TBq. The implications of these results for a rehabilitation program are discussed

Recommendations for determining the surface contamination of the skin and estimating radiation exposure of the skin after contamination

International Nuclear Information System (INIS)

1989-01-01

The recommendations are applicable to the determination of surface contaminations of the skin and to the estimation of the expected radiation exposure of the skin of contaminated persons. According to the present recommendations, the radiation exposure can only be estimated for the intact and healthy skin

Evaluation of Contamination Inspection and Analysis Methods through Modeling System Performance

Science.gov (United States)

Seasly, Elaine; Dever, Jason; Stuban, Steven M. F.

2016-01-01

Contamination is usually identified as a risk on the risk register for sensitive space systems hardware. Despite detailed, time-consuming, and costly contamination control efforts during assembly, integration, and test of space systems, contaminants are still found during visual inspections of hardware. Improved methods are needed to gather information during systems integration to catch potential contamination issues earlier and manage contamination risks better. This research explores evaluation of contamination inspection and analysis methods to determine optical system sensitivity to minimum detectable molecular contamination levels based on IEST-STD-CC1246E non-volatile residue (NVR) cleanliness levels. Potential future degradation of the system is modeled given chosen modules representative of optical elements in an optical system, minimum detectable molecular contamination levels for a chosen inspection and analysis method, and determining the effect of contamination on the system. By modeling system performance based on when molecular contamination is detected during systems integration and at what cleanliness level, the decision maker can perform trades amongst different inspection and analysis methods and determine if a planned method is adequate to meet system requirements and manage contamination risk.

Predictors of Heavy Stethoscope Contamination Following a Physical Examination.

Science.gov (United States)

Tschopp, Clément; Schneider, Alexis; Longtin, Yves; Renzi, Gesuele; Schrenzel, Jacques; Pittet, Didier

2016-06-01

BACKGROUND The degree of bacterial contamination of stethoscopes can vary significantly following a physical examination. OBJECTIVE To conduct a prospective study to investigate the impact of various environmental and patient characteristics on stethoscope contamination. METHODS Following a standardized examination, the levels of bacterial contamination of 4 regions of the physicians' hands and 2 sections of the stethoscopes, and the presence of different pathogenic bacteria, were assessed. Predictors of heavy stethoscope contamination were identified through multivariate logistic regression. RESULTS In total, 392 surfaces were sampled following examination of 56 patients. The microorganisms most frequently recovered from hands and stethoscopes were Enterococcus spp. (29% and 20%, respectively) and Enterobacteriaceae (16% and 7%, respectively). Staphylococcus aureus (either methicillin susceptible or resistant), extended-spectrum β-lactamase-producing Enterobacteriaceae, and Acinetobacter baumannii were recovered from 4%-9% of the samples from either hands or stethoscopes. There was a correlation between the likelihood of recovering these pathogens from the stethoscopes vs from the physicians' hands (ρ=0.79; P=.04). The level of patient's skin contamination was an independent predictor of contamination of the stethoscope diaphragm (adjusted odds ratio [aOR], 1.001; P=.007) and tube (aOR, 1.001; P=.003). Male sex (aOR, 28.24; P=.01) and reception of a bed bath (aOR, 7.52; P=.048) were also independently associated with heavy tube contamination. CONCLUSIONS Stethoscope contamination following a single physical examination is not negligible and is associated with the level of contamination of the patient's skin. Prevention of pathogen dissemination is needed. Infect Control Hosp Epidemiol 2016;37:673-679.

Radioactive contamination in environment and food in Poland in 1992

International Nuclear Information System (INIS)

Grabowski, D.; Muszynski, W.; Petrykowska, M.; Rubel, B.; Smagala, G.; Wilgos, J.

1993-01-01

The level analysis of the level of radioactive contamination in environment and food samples was carried out in Poland in 1992. The results were compared to the data from 1985-1991 period. Since the Chernobyl accident gradual decrease of contamination level has been stated. The gamma dose rate and the contamination of air, fallout, tap and surface water were at the level of 1985. Still higher contamination level of cesium isotopes in soil has been reported and as a consequence food contamination was higher particularly the animal food. Actually, the source of additional dose is ingestion of artificial isotopes with food as a result of food contamination. The average effective dose equivalent, due to the contaminated food consumption, was estimated at the level 15 μSv for a Pole in 1992. (author). 13 refs, 6 figs, 20 tabs

Contamination control research activities for space optics in JAXA RANDD

Science.gov (United States)

Kimoto, Y.

2017-11-01

Contamination control research activities for space optics projects in JAXA R&D are described. More accurate contamination control techniques are requested because of intensified recent science mission requirements. One approach to control the contamination effects is analysis by software. JAXA has been developing a contamination analytical tool "J-SPICE" (Japanese Spacecraft Induced Contamination analysis software) as well as experiment facilities to improve the J-SPICE. A reflection model in J-SPICE has been experimentally verified and outgassing model data has been acquired by a facility. JAXA has developed a facility which could determine the influence of the contamination at a specific wavelength by combining a vacuum chamber with an I-R spectrometer and performed an experiment to inspect the effect of baking. Space material exposure experiment results reveal the actual thickness of the contamination layer in ISS orbit.

Fall 1998 200 East area biological vector contamination report

International Nuclear Information System (INIS)

CONNELL, D.J.

1999-01-01

The purpose of this report is to document the investigation into the cause of the spread of radioactive contamination in September and October 1998 at the Hanford Site's 200 East Area and its subsequent spread to the City of Richland Landfill; identify the source of the contamination; and present corrective actions. The focus and thrust of managing the incident was based on the need to accomplish the following, listed in order of importance: (1) protect the health and safety of the Site workers and the public; (2) contain and control the spread of contamination; (3) identify the source of contamination and the pathways for its spread; and (4) identify the causal factors enabling the contamination

Regenerable Air Purification System for Gas-Phase Contaminant Control

Science.gov (United States)

Constantinescu, Ileana C.; Finn, John E.; LeVan, M. Douglas; Lung, Bernadette (Technical Monitor)

2000-01-01

Tests of a pre-prototype regenerable air purification system (RAPS) that uses water vapor to displace adsorbed contaminants from an adsorbent column have been performed at NASA Ames Research Center. A unit based on this design can be used for removing trace gas-phase contaminants from spacecraft cabin air or from polluted process streams including incinerator exhaust. During the normal operation mode, contaminants are removed from the air on the column. Regeneration of the column is performed on-line. During regeneration, contaminants are displaced and destroyed inside the closed oxidation loop. In this presentation we discuss initial experimental results for the performance of RAPS in the removal and treatment of several important spacecraft contaminant species from air.

Fall 1998 200 East area biological vector contamination report

Energy Technology Data Exchange (ETDEWEB)

CONNELL, D.J.

1999-03-17

The purpose of this report is to document the investigation into the cause of the spread of radioactive contamination in September and October 1998 at the Hanford Site's 200 East Area and its subsequent spread to the City of Richland Landfill; identify the source of the contamination; and present corrective actions. The focus and thrust of managing the incident was based on the need to accomplish the following, listed in order of importance: (1) protect the health and safety of the Site workers and the public; (2) contain and control the spread of contamination; (3) identify the source of contamination and the pathways for its spread; and (4) identify the causal factors enabling the contamination.

Psychological aspects of personnel contamination

International Nuclear Information System (INIS)

Wilson, R.L.

1985-04-01

This paper discusses some of the major emotional considerations involved in the treatment of people who have been contaminated with potentially hazardous materials. Although the principal focus is the treatment of people trained to work with these materials, an attempt is also made to extend these methods to people having little or no knowledge of such matters. Accidents always result in emotional trauma. When the accident involves radioactive or other potentially toxic, carcinogenic, or mutagenic materials, there is a possibility of enhanced emotional stress due to the mystique surrounding these substances. Several psychological principles that have emerged from the treatment of radioactively-contaminated workers are: (1) provide pre-accident training for all radiation workers; (2) avoid secrets; (3) as rapidly as possible following a contamination accident, bring the worker into contact with others; (4) recognize the emotions of the family and the family's fears and trauma; and (5) do not desert the worker after decontamination has been completed. 1 ref

Geoelectrical mapping and groundwater contamination

Science.gov (United States)

Blum, Rainer

Specific electrical resistivity of near-surface materials is mainly controlled by the groundwater content and thus reacts extremely sensitive to any change in the ion content. Geoelectric mapping is a well-established, simple, and inexpensive technique for observing areal distributions of apparent specific electrical resistivities. These are a composite result of the true resistivities in the underground, and with some additional information the mapping of apparent resistivities can help to delineate low-resistivity groundwater contaminations, typically observed downstream from sanitary landfills and other waste sites. The presence of other good conductors close to the surface, mainly clays, is a serious noise source and has to be sorted out by supporting observations of conductivities in wells and geoelectric depth soundings. The method may be used to monitor the extent of groundwater contamination at a specific time as well as the change of a contamination plume with time, by carrying out repeated measurements. Examples for both are presented.

Bioremediation of petroleum contaminated soil

International Nuclear Information System (INIS)

Autry, A.R.; Ellis, G.M.

1992-01-01

This paper reports on bioremediation, which offers a cost-competitive, effective remediation alternative for soil contaminated with petroleum products. These technologies involve using microorganisms to biologically degrade organic constituents in contaminated soil. All bioremediation applications must mitigate various environmental rate limiting factors so that the biodegradation rates for petroleum hydrocarbons are optimized in field-relevant situations. Traditional bioremediation applications include landfarming, bioreactors, and composting. A more recent bioremediation application that has proven successful involves excavation of contaminated soil. The process involves the placement of the soils into a powerscreen, where it is screened to remove rocks and larger debris. The screened soil is then conveyed to a ribbon blender, where it is mixed in batch with nutrient solution containing nitrogen, phosphorus, water, and surfactants. Each mixed soil batch is then placed in a curing pile, where it remains undisturbed for the remainder of the treatment process, during which time biodegradation by naturally occurring microorganisms, utilizing biochemical pathways mediated by enzymes, will occur

Hybrid electrokinetic method applied to mix contaminated soil

Energy Technology Data Exchange (ETDEWEB)

Mansour, H.; Maria, E. [Dept. of Building Civil and Environmental Engineering, Concordia Univ., Montreal (Canada)

2001-07-01

Several industrials and municipal areas in North America are contaminated with heavy metals and petroleum products. This mix contamination presents a particularly difficult task for remediation when is exposed in clayey soil. The objective of this research was to find a method to cleanup mix contaminated clayey soils. Finally, a multifunctional hybrid electrokinetic method was investigated. Clayey soil was contaminated with lead and nickel (heavy metals) at the level of 1000 ppm and phenanthrene (PAH) of 600 ppm. Electrokinetic surfactant supply system was applied to mobilize, transport and removal of phenanthrene. A chelation agent (EDTA) was also electrokinetically supplied to mobilize heavy metals. The studies were performed on 8 lab scale electrokinetic cells. The mix contaminated clayey soil was subjected to DC total voltage gradient of 0.3 V/cm. Supplied liquids (surfactant and EDTA) were introduced in different periods of time (22 days, 42 days) in order to optimize the most excessive removal of contaminants. The ph, electrical parameters, volume supplied, and volume discharged was monitored continuously during each experiment. At the end of these tests soil and cathalyte were subjected to physico-chemical analysis. The paper discusses results of experiments including the optimal energy use, removal efficiency of phenanthrene, as well, transport and removal of heavy metals. The results of this study can be applied for in-situ hybrid electrokinetic technology to remediate clayey sites contaminated with petroleum product mixed with heavy metals (e.g. manufacture Gas Plant Sites). (orig.)

Bioremediation of contaminated soil: Strategy and case histories

International Nuclear Information System (INIS)

Balba, M.T.; Ying, A.C.; McNeice, T.G.

1991-01-01

Microorganisms are capable of degrading many kinds of xenobiotic compounds and toxic chemicals. These microorganisms are ubiquitous in nature and there are numerous cases in which long-term contamination of soil and groundwater has been observed. The persistence of the contamination is usually caused by the inability of micro-organisms to metabolize these compounds under the prevailing environmental conditions. Two general reasons account for the failure of microbes to degrade pollutants in any environment: (1) inherent molecular recalcitrance of the contaminants and (2) environmental factors. The inherent molecular recalcitrance is usually associated with xenobiotic compounds where the chemical structure of the molecule is such that microbes and enzymes required for its catabolism have not evolved yet in nature. The environmental factors include a range of physicochemical conditions which influence microbial growth and activity. Biological remediation of contaminated sites can be accomplished using naturally-occurring microorganisms to treat the contaminants. Only particular groups of microorganisms are capable of decomposing specific compounds. The development of a bioremediation program for a specific contaminated soil system usually includes: thorough site/soil/waste characterization; treatability studies; and design and implementation of the bioremediation plan. The results of in situ and ex situ treatment programs involving the cleanup of petroleum hydrocarbon-contaminated soil will be discussed in detail. The paper will address key issues affecting the success of the bioremediation process such as nutrient transport, metal precipitation and potential soil clogging, microbial inoculation, etc

Lifting the veil: Impact of contaminants on coastal phytoplankton

NARCIS (Netherlands)

Sjollema, S.B.

2014-01-01

Coastal waters are among the most productive ecosystems on the planet. Yet, they also suffer from a high contaminant load, resulting in a ‘grey veil’ of contaminants. Exposure of microalgal communities to these contaminants potentially results in shifts in microalgal community composition. As

Bioremediation of soil contaminated with spent and fresh cutting ...

African Journals Online (AJOL)

Contamination of soil with industrial cutting fluids containing heavy metals and petroleum hydrocarbons has detrimental effects on ecosystems. As such contaminants constitute risk to human health; they can enter the food chain through agricultural products or contaminated drinking water. This growing concern about ...

Delineating Landfill Leachate Discharge To An Arsenic Contaminated Waterway

Science.gov (United States)

Discharge of contaminated ground water may serve as a primary and on-going source of contamination to surface water. A field investigation was conducted at a Superfund site in Massachusetts, USA to define the locus of contaminant flux and support source identification for arseni...

IN SITU REMEDIATION OF CONTAMINATED SEDIMENTS - ACTIVE CAPPING TECHNOLOGY

Energy Technology Data Exchange (ETDEWEB)

Knox, A.; Roberts, J.; Paller, M.; Reible, D.

2010-09-02

Active capping is a relatively new approach for treating contaminated sediments. It involves applying chemically reactive amendments to the sediment surface. The main role of active caps is to stabilize contaminants in contaminated sediments, lower the bioavailable pool of contaminants, and reduce the release of contaminants to the water column. Metals are common contaminants in many marine and fresh water environments as a result of industrial and military activities. The mobile, soluble forms of metals are generally considered toxic. Induced chemical precipitation of these metals can shift toxic metals from the aqueous phase to a solid, precipitated phase which is often less bioavailable. This approach can be achieved through application of sequestering agents such as rock phosphates, organoclays, zeolites, clay minerals, and biopolymers (e.g., chitosan) in active capping technology. Active capping holds great potential for a more permanent solution that avoids residual risks resulting from contaminant migration through the cap or breaching of the cap. In addition to identifying superior active capping agents, research is needed to optimize application techniques, application rates, and amendment combinations that maximize sequestration of contaminants. A selected set of active capping treatment technologies has been demonstrated at a few sites, including a field demonstration at the Savannah River Site, Aiken, SC. This demonstration has provided useful information on the effects of sequestering agents on metal immobilization, bioavailability, toxicity, and resistance to mechanical disturbance.

Contamination of Detained Sediment in Sustainable Urban Drainage Systems

Directory of Open Access Journals (Sweden)

Deonie Allen

2017-05-01

Full Text Available Adsorption is a key water pollution remediation measure used to achieve stormwater quality improvement in Sustainable urban Drainage Systems (SuDS. The level of contamination of detained sediment within SuDS assets is not well documented, with published investigations limited to specific contaminant occurrence in ponds, wetlands or infiltration devices (bioretention cells and generally focused on solute or suspended sediment. Guidance on contamination threshold levels and potential deposited sediment contamination information is not included in current UK SuDS design or maintenance guidance, primarily due to a lack of evidence and understanding. There is a need to understand possible deposited sediment contamination levels in SuDS, specifically in relation to sediment removal maintenance activities and potential impact on receiving waterways of conveyed sediment. Thus, the objective of the research presented herein was to identify what major elements and trace metals were observable in (the investigated SuDS assets detained sediment, the concentration of these major elements and trace metals and whether they met/surpassed ecotoxicity or contaminated land thresholds. The research presented here provides evidence of investigated SuDS sediment major element and trace metal levels to help inform guidance and maintenance needs, and presents a new methodology to identify the general cause (anthropocentric land use and extent of detained SuDS fine urban sediment contamination through use of a contamination matrix.

In Situ Remediation Of Contaminated Sediments - Active Capping Technology

International Nuclear Information System (INIS)

Knox, A.; Roberts, J.; Paller, M.; Reible, D.

2010-01-01

Active capping is a relatively new approach for treating contaminated sediments. It involves applying chemically reactive amendments to the sediment surface. The main role of active caps is to stabilize contaminants in contaminated sediments, lower the bioavailable pool of contaminants, and reduce the release of contaminants to the water column. Metals are common contaminants in many marine and fresh water environments as a result of industrial and military activities. The mobile, soluble forms of metals are generally considered toxic. Induced chemical precipitation of these metals can shift toxic metals from the aqueous phase to a solid, precipitated phase which is often less bioavailable. This approach can be achieved through application of sequestering agents such as rock phosphates, organoclays, zeolites, clay minerals, and biopolymers (e.g., chitosan) in active capping technology. Active capping holds great potential for a more permanent solution that avoids residual risks resulting from contaminant migration through the cap or breaching of the cap. In addition to identifying superior active capping agents, research is needed to optimize application techniques, application rates, and amendment combinations that maximize sequestration of contaminants. A selected set of active capping treatment technologies has been demonstrated at a few sites, including a field demonstration at the Savannah River Site, Aiken, SC. This demonstration has provided useful information on the effects of sequestering agents on metal immobilization, bioavailability, toxicity, and resistance to mechanical disturbance.

Contaminant Gradients in Trees: Directional Tree Coring Reveals Boundaries of Soil and Soil-Gas Contamination with Potential Applications in Vapor Intrusion Assessment.

Science.gov (United States)

Wilson, Jordan L; Samaranayake, V A; Limmer, Matthew A; Schumacher, John G; Burken, Joel G

2017-12-19

Contaminated sites pose ecological and human-health risks through exposure to contaminated soil and groundwater. Whereas we can readily locate, monitor, and track contaminants in groundwater, it is harder to perform these tasks in the vadose zone. In this study, tree-core samples were collected at a Superfund site to determine if the sample-collection location around a particular tree could reveal the subsurface location, or direction, of soil and soil-gas contaminant plumes. Contaminant-centroid vectors were calculated from tree-core data to reveal contaminant distributions in directional tree samples at a higher resolution, and vectors were correlated with soil-gas characterization collected using conventional methods. Results clearly demonstrated that directional tree coring around tree trunks can indicate gradients in soil and soil-gas contaminant plumes, and the strength of the correlations were directly proportionate to the magnitude of tree-core concentration gradients (spearman's coefficient of -0.61 and -0.55 in soil and tree-core gradients, respectively). Linear regression indicates agreement between the concentration-centroid vectors is significantly affected by in planta and soil concentration gradients and when concentration centroids in soil are closer to trees. Given the existing link between soil-gas and vapor intrusion, this study also indicates that directional tree coring might be applicable in vapor intrusion assessment.

Decrease DNA contamination in the laboratories

DEFF Research Database (Denmark)

Kampmann, Marie-Louise; Børsting, Claus; Morling, Niels

2017-01-01

In this study, we tested various approaches to remove DNA from hard laboratory surfaces. We contaminated clean surfaces with four different concentrations of massively parallel sequencing libraries. The DNA was dried and left for 45 min and for 24 h, respectively, before any treatment. The surfaces.......9–1.8% hypochlorite in order to eliminate laboratory contamination and simultaneously minimise any poisonous gases....

Uptake of inorganic contaminants by pteridophytes

International Nuclear Information System (INIS)

Zheng Jiemin; Chen Ziyuan; Tang Shirong; Guangzhou Univ., Guangzhou; Ding Bingyang

2005-01-01

The review covers results at home and abroad in terms of uptake of inorganic contaminants by pteridophytes, and suggests pteridophytes' significance in phytoremediation; the mechanisms related to uptake of inorganic contaminants by pteridophytes and some methods and means used for research on the mechanism are also introduced; the authors' viewpoints on future development trends are presented in this paper. (authors)

Groundwater pumping effects on contaminant loading management in agricultural regions.

Science.gov (United States)

Park, Dong Kyu; Bae, Gwang-Ok; Kim, Seong-Kyun; Lee, Kang-Kun

2014-06-15

Groundwater pumping changes the behavior of subsurface water, including the location of the water table and characteristics of the flow system, and eventually affects the fate of contaminants, such as nitrate from agricultural fertilizers. The objectives of this study were to demonstrate the importance of considering the existing pumping conditions for contaminant loading management and to develop a management model to obtain a contaminant loading design more appropriate and practical for agricultural regions where groundwater pumping is common. Results from this study found that optimal designs for contaminant loading could be determined differently when the existing pumping conditions were considered. This study also showed that prediction of contamination and contaminant loading management without considering pumping activities might be unrealistic. Motivated by these results, a management model optimizing the permissible on-ground contaminant loading mass together with pumping rates was developed and applied to field investigation and monitoring data from Icheon, Korea. The analytical solution for 1-D unsaturated solute transport was integrated with the 3-D saturated solute transport model in order to approximate the fate of contaminants loaded periodically from on-ground sources. This model was further expanded to manage agricultural contaminant loading in regions where groundwater extraction tends to be concentrated in a specific period of time, such as during the rice-growing season, using a method that approximates contaminant leaching to a fluctuating water table. The results illustrated that the simultaneous management of groundwater quantity and quality was effective and appropriate to the agricultural contaminant loading management and the model developed in this study, which can consider time-variant pumping, could be used to accurately estimate and to reasonably manage contaminant loading in agricultural areas. Copyright © 2014 Elsevier Ltd. All

Phytoremediation of soils contaminated with radionuclides

International Nuclear Information System (INIS)

Yamaguchi, Isamu

2004-01-01

Aiming at efficient phytoremediation of soils contaminated with radionuclides, we examined the effect of soil microbes on the uptake ability of plants using the multitracer technique to find that tomato rhizofungi in Fusarium spp. can stimulate the uptake of 85 Sr and 137 Cs by the plants. The synergic effect of a nonpathogenic strain of F. oxysporum on the uptake of radionuclides by plants proved to be enhanced by introducing a phytochelatin synthase gene into the fungus. Since soil contamination by radionuclides is still an unsolved problem in many parts of the world. Studies on phytoremediation of polluted soil environment will be important for developing effective strategies and devising adequate techniques to reduce human risks caused by food contamination of radionuclides. (author)

Phytoforensics—Using trees to find contamination

Science.gov (United States)

Wilson, Jordan L.

2017-09-28

The water we drink, air we breathe, and soil we come into contact with have the potential to adversely affect our health because of contaminants in the environment. Environmental samples can characterize the extent of potential contamination, but traditional methods for collecting water, air, and soil samples below the ground (for example, well drilling or direct-push soil sampling) are expensive and time consuming. Trees are closely connected to the subsurface and sampling tree trunks can indicate subsurface pollutants, a process called phytoforensics. Scientists at the Missouri Water Science Center were among the first to use phytoforensics to screen sites for contamination before using traditional sampling methods, to guide additional sampling, and to show the large cost savings associated with tree sampling compared to traditional methods. 

Combating radiocesium contamination in farm animals

International Nuclear Information System (INIS)

Hove, K.; Ekern, A.

1988-01-01

Considerable amounts of radioactive fallout from the Chernobyl accident swept central parts of Norway, where especially native mountain areas but also some agricultural land were heavily contaminated. Parts of the heavily polluted areas are important in Norwegian animal production, being grazed by reindeer all year, and by sheep, goats and cattle in the summer. Cs-137 and Cs-134 appeared in feeds shortly after the accident and the levels increased throughout the summer. In this paper some of the results obtained in experiments with contaminated animals in Norway are reviewed. Experiments in connection with the use of uncontaminated feeds for decontamination of farm animals, the transfer of radioactivity to milk, and the use of cesiumbinders to reduce cesium contamination are described

Decontamination method for radiation contaminated metal

International Nuclear Information System (INIS)

Enda, Masami; Hosaka, Katsumi; Sakai, Hitoshi.

1997-01-01

An organic acid solution is used as a decontamination liquid, and base materials of radiation contaminated metals are dissolved in the solution. The concentration of the organic acid is measured, and the organic acid is supplied by an amount corresponding to the lowering of the concentration. The decontamination liquid wastes generated during the decontamination step are decomposed, and metals leached in the organic acid solution are separated. With such procedures, contamination intruded into the inside of the mother materials of the metals can be removed, and radioactivity of the contaminated metals such as stainless steels and carbon steels can be eliminated, or the radiation level thereof can be reduced. In addition, the amount of secondary wastes generated along with the decontamination can be suppressed. (T.M.)

Analysis of food contaminants

National Research Council Canada - National Science Library

Gilbert, John

1984-01-01

... quantification methods used in the analysis of mycotoxins in foods - Confirmation and quantification of trace organic food contaminants by mass spectrometry-selected ion monitoring - Chemiluminescence...

The Sources of Chemical Contaminants in Food and Their Health Implications

Directory of Open Access Journals (Sweden)

Irfan A. Rather

2017-11-01

Full Text Available Food contamination is a matter of serious concern, as the high concentration of chemicals present in the edibles poses serious health risks. Protecting the public from the degrees of the harmfulness of contaminated foods has become a daunting task. This article highlights the causes, types, and health implications of chemical contamination in food. The food contamination could be due to naturally occurring contaminants in the environment or artificially introduced by the human. The phases of food processing, packaging, transportation, and storage are also significant contributors to food contamination. The implications of these chemical contaminants on human health are grave, ranging from mild gastroenteritis to fatal cases of hepatic, renal, and neurological syndromes. Although, the government regulates such chemicals in the eatables by prescribing minimum limits that are safe for human consumption yet measures still need to be taken to curb food contamination entirely. Therefore, a variety of food needs to be inspected and measured for the presence of chemical contaminants. The preventative measures pertaining about the food contaminants problems are pointed out and discussed.

The Sources of Chemical Contaminants in Food and Their Health Implications

Science.gov (United States)

Rather, Irfan A.; Koh, Wee Yin; Paek, Woon K.; Lim, Jeongheui

2017-01-01

Food contamination is a matter of serious concern, as the high concentration of chemicals present in the edibles poses serious health risks. Protecting the public from the degrees of the harmfulness of contaminated foods has become a daunting task. This article highlights the causes, types, and health implications of chemical contamination in food. The food contamination could be due to naturally occurring contaminants in the environment or artificially introduced by the human. The phases of food processing, packaging, transportation, and storage are also significant contributors to food contamination. The implications of these chemical contaminants on human health are grave, ranging from mild gastroenteritis to fatal cases of hepatic, renal, and neurological syndromes. Although, the government regulates such chemicals in the eatables by prescribing minimum limits that are safe for human consumption yet measures still need to be taken to curb food contamination entirely. Therefore, a variety of food needs to be inspected and measured for the presence of chemical contaminants. The preventative measures pertaining about the food contaminants problems are pointed out and discussed. PMID:29204118

Tritium contamination of hematopoietic stem cells alters long-term hematopoietic reconstitution

International Nuclear Information System (INIS)

Di Giacomo, F.; Barroca, V.; Laurent, D.; Lewandowski, D.; Saintigny, Y.; Romeo, P.H.; Granotier, Ch.; Boussin, F.D.

2011-01-01

Purpose: In vivo effects of tritium contamination are poorly documented. Here, we study the effects of tritiated Thymidine ([ 3 H] Thymidine) or tritiated water (HTO) contamination on the biological properties of hematopoietic stem cells (HSC). Materials and methods: Mouse HSC were contaminated with concentrations of [ 3 H] Thymidine ranging from 0.37-37.03 kBq/ml or of HTO ranging from 5-50 kBq/ml. The biological properties of contaminated HSC were studied in vitro after HTO contamination and in vitro and in vivo after [ 3 H] Thymidine contamination. Results: Proliferation, viability and double-strand breaks were dependent on [ 3 H] Thymidine or HTO concentrations used for contamination but in vitro myeloid differentiation of HSC was not affected by [ 3 H] Thymidine contamination. [ 3 H] Thymidine contaminated HSC showed a compromised long-term capacity of hematopoietic reconstitution and competition experiments showed an up to two-fold decreased capacity of contaminated HSC to reconstitute hematopoiesis. These defects were not due to impaired homing in bone marrow but to an initial decreased proliferation rate of HSC. Conclusion: These results indicate that contaminations of HSC with doses of tritium that do not result in cell death, induce short-term effects on proliferation and cell cycle and long-term effects on hematopoietic reconstitution capacity of contaminated HSC. (authors)

Uptake by Plants of Radiostrontium from Contaminated Soils

DEFF Research Database (Denmark)

Andersen, A. J.

1965-01-01

In a recent report from this department it was shown that the extractability of radiostrontium from contaminated soil samples was effectively reduced by heat treatment and by the addition of phosphate to the soil. It was pointed out that, under emergency conditions, heat-treatment of the contamin......In a recent report from this department it was shown that the extractability of radiostrontium from contaminated soil samples was effectively reduced by heat treatment and by the addition of phosphate to the soil. It was pointed out that, under emergency conditions, heat......-treatment of the contaminated soil surface and heavy phosphate application might thus reduce the uptake by plants of radiostrontium more efficiently than liming, which is only effective in soils of low calcium status. In the investigation reviewed here the influence of heat treatment and superphosphate application on the plant...... uptake of radiostrontium was examined in pot experiments. For comparison the effect of applying calcium carbonate to the contaminated soil surface was also determined....

Remediation of Contaminated Soils by Solvent Flushing

NARCIS (Netherlands)

Augustijn, Dionysius C.M.; Jessup, Ron E.; Rao, P. Suresh C.; Wood, A. Lynn

1994-01-01

Solvent flushing is a potential technique for remediating a waste disposal/spill site contaminated with organic chemicals. This technique involves the injection of a solvent mixture (e.g., water plus alcohols) that enhances contaminant solubility, reduces the retardation factor, and increases the

Minimizing electrode contamination in an electrochemical cell

Science.gov (United States)

Kim, Yu Seung; Zelenay, Piotr; Johnston, Christina

2014-12-09

An electrochemical cell assembly that is expected to prevent or at least minimize electrode contamination includes one or more getters that trap a component or components leached from a first electrode and prevents or at least minimizes them from contaminating a second electrode.

Water in the March river radioactively contaminated

International Nuclear Information System (INIS)

Englander, A.G.

1990-01-01

A curve of the tritium contamination of the March river measured in Austria from 1976 to 1989 is shown. The conjecture is put forward that this contamination is caused by the Dukovani power plant in the neighbouring CSFR. Further measurements are called for

Organic contaminants in soil : desorption kinetics and microbial degradation

NARCIS (Netherlands)

Schlebaum, W.

1999-01-01

The availability of organic contaminants in soils or sediments for microbial degradation or removal by physical means (e.g.) soil washing or soil venting) depends on the desorption kinetics of these contaminants from the soil matrix. When the organic contaminants desorb very slow from the

40 CFR 159.179 - Metabolites, degradates, contaminants, and impurities.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 23 2010-07-01 2010-07-01 false Metabolites, degradates, contaminants.../Benefit Information § 159.179 Metabolites, degradates, contaminants, and impurities. (a) Metabolites and... degradation of less than 10 percent in a 30-day period. (b) Contaminants and impurities. The presence in any...

Monitoring of atmospheric contamination by plutonium in laboratories

International Nuclear Information System (INIS)

Pomarola, J.; Risselin, A.; Feliers, P.

1965-02-01

Immediate detection of atmospheric contamination by plutonium is necessary for warning of operators. A precise estimate of the level of this contamination is also necessary in order to give the Medical Section proper information. Experiments have been carried out at CEN-FAR using atmospheric contamination by plutonium monitors. This paper deals successively with: important problems of monitoring, the carrying out of the experiments and the results yielded. (authors) [fr

Quantifying Diffuse Contamination: Method and Application to Pb in Soil.

Science.gov (United States)

Fabian, Karl; Reimann, Clemens; de Caritat, Patrice

2017-06-20

A new method for detecting and quantifying diffuse contamination at the continental to regional scale is based on the analysis of cumulative distribution functions (CDFs). It uses cumulative probability (CP) plots for spatially representative data sets, preferably containing >1000 determinations. Simulations demonstrate how different types of contamination influence elemental CDFs of different sample media. It is found that diffuse contamination is characterized by a distinctive shift of the low-concentration end of the distribution of the studied element in its CP plot. Diffuse contamination can be detected and quantified via either (1) comparing the distribution of the contaminating element to that of an element with a geochemically comparable behavior but no contamination source (e.g., Pb vs Rb), or (2) comparing the top soil distribution of an element to the distribution of the same element in subsoil samples from the same area, taking soil forming processes into consideration. Both procedures are demonstrated for geochemical soil data sets from Europe, Australia, and the U.S.A. Several different data sets from Europe deliver comparable results at different scales. Diffuse Pb contamination in surface soil is estimated to be contamination sources and can be used to efficiently monitor diffuse contamination at the continental to regional scale.

Radioactive standards and calibration methods for contamination monitoring instruments

Energy Technology Data Exchange (ETDEWEB)

Yoshida, Makoto [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

1997-06-01

Contamination monitoring in the facilities for handling unsealed radioactive materials is one of the most important procedures for radiation protection as well as radiation dose monitoring. For implementation of the proper contamination monitoring, radiation measuring instruments should not only be suitable to the purpose of monitoring, but also be well calibrated for the objective qualities of measurement. In the calibration of contamination monitoring instruments, quality reference activities need to be used. They are supplied in different such as extended sources, radioactive solutions or radioactive gases. These reference activities must be traceable to the national standards or equivalent standards. On the other hand, the appropriate calibration methods must be applied for each type of contamination monitoring instruments. In this paper, the concepts of calibration for contamination monitoring instruments, reference sources, determination methods of reference quantities and practical calibration methods of contamination monitoring instruments, including the procedures carried out in Japan Atomic Energy Research Institute and some relevant experimental data. (G.K.)

Estimating contaminant discharge rates from stabilized uranium tailings embankments

International Nuclear Information System (INIS)

Weber, M.F.

1986-01-01

Estimates of contaminant discharge rates from stabilized uranium tailings embankments are essential in evaluating long-term impacts of tailings disposal on groundwater resources. Contaminant discharge rates are a function of water flux through tailings covers, the mass and distribution of tailings, and the concentrations of contaminants in percolating pore fluids. Simple calculations, laboratory and field testing, and analytical and numerical modeling may be used to estimate water flux through variably-saturated tailings under steady-state conditions, which develop after consolidation and dewatering have essentially ceased. Contaminant concentrations in water discharging from the tailings depend on tailings composition, leachability and solubility of contaminants, geochemical conditions within the embankment, tailings-water interactions, and flux of water through the embankment. These concentrations may be estimated based on maximum reported concentrations, pore water concentrations, extrapolations of column leaching data, or geochemical equilibria and reaction pathway modeling. Attempts to estimate contaminant discharge rates should begin with simple, conservative calculations and progress to more-complicated approaches, as necessary

Contaminant Boundary at the Faultless Underground Nuclear Test

International Nuclear Information System (INIS)

Greg Pohll; Karl Pohlmann; Jeff Daniels; Ahmed Hassan; Jenny Chapman

2003-01-01

The U.S. Department of Energy (DOE) and the Nevada Division of Environmental Protection (NDEP) have reached agreement on a corrective action strategy applicable to address the extent and potential impact of radionuclide contamination of groundwater at underground nuclear test locations. This strategy is described in detail in the Federal Facility Agreement and Consent Order (FFACO, 2000). As part of the corrective action strategy, the nuclear detonations that occurred underground were identified as geographically distinct corrective action units (CAUs). The strategic objective for each CAU is to estimate over a 1,000-yr time period, with uncertainty quantified, the three-dimensional extent of groundwater contamination that would be considered unsafe for domestic and municipal use. Two types of boundaries (contaminant and compliance) are discussed in the FFACO that will map the three-dimensional extent of radionuclide contamination. The contaminant boundary will identify the region wi th 95 percent certainty that contaminants do not exist above a threshold value. It will be prepared by the DOE and presented to NDEP. The compliance boundary will be produced as a result of negotiation between the DOE and NDEP, and can be coincident with, or differ from, the contaminant boundary. Two different thresholds are considered for the contaminant boundary. One is based on the enforceable National Primary Drinking Water Regulations for radionuclides, which were developed as a requirement of the Safe Drinking Water Act. The other is a risk-based threshold considering applicable lifetime excess cancer-risk-based criteria The contaminant boundary for the Faultless underground nuclear test at the Central Nevada Test Area (CNTA) is calculated using a newly developed groundwater flow and radionuclide transport model that incorporates aspects of both the original three-dimensional model (Pohlmann et al., 1999) and the two-dimensional model developed for the Faultless data decision

Viral Contamination Source in Clinical Microbiology Laboratory.

Science.gov (United States)

Wang, Xin Ling; Song, Juan; Song, Qin Qin; Yu, Jie; Luo, Xiao Nuan; Wu, Gui Zhen; Han, Jun

2016-08-01

To understand the potential causes of laboratory-acquired infections and to provide possible solutions that would protect laboratory personnel, samples from a viral laboratory were screened to determine the main sources of contamination with six subtypes of Rhinovirus. Rhinovirus contamination was found in the gloves, cuffs of protective wear, inner surface of biological safety cabinet (BSC) windows, and trash handles. Remarkably, high contamination was found on the inner walls of the centrifuge and the inner surface of centrifuge tube casing in the rotor. Spilling infectious medium on the surface of centrifuge tubes was found to contribute to contamination of centrifuge surfaces. Exposure to sodium hypochlorite containing no less than 0.2 g/L available chlorine decontaminated the surface of the centrifuge tubes from Rhinovirus after 2 min. Copyright © 2016 The Editorial Board of Biomedical and Environmental Sciences. Published by China CDC. All rights reserved.

Guide to treatment technology for contaminated soils

International Nuclear Information System (INIS)

Tran, H.; Aylward, R.

1992-01-01

This document is a guide for the screening of alternative treatment technologies for contaminated soils. The contents of this guide are organized into: 1. Introduction, II. Utilizing the table, III. Tables: Contamination Versus Technology, TV. Contaminant Waste Groups, and V. References. The four Contaminations Versus Technology tables are designed to identify the effectiveness and/or potential applicability of technologies to some or all compounds within specific waste groups. The tables also present limitations and special use considerations for the particular treatment technology. The phase of development of the technology is also included in the table. The phases are: Available, Innovative, and Emerging technologies. The technologies presented in this guide are organized according to the method of treatment. The four (4) treatment methods are Biological, Solidification/Stabilization, Thermal, and Chemical/Physical Treatment. There are several processing methods; some are well developed and proven, and others are in the development stage

Kinetic model for the dosimetry of radiopharmaceuticals contaminated by Mo-99

International Nuclear Information System (INIS)

Shearer, D.R.; Pezzullo, J.C.

1986-01-01

Radiopharmaceuticals tagged with Tc-99m may become contaminated with breakthrough products from the Mo-99/Tc-99m generator. If a fraction of the contaminant becomes bound to the radiopharmaceutical, the dose to the radiopharmaceutical target organ from the contaminant must be considered. The dose to the contaminant target organ may then be calculated as the sum of the doses from a) the initially unbound contaminant, and b) the contaminant later released by degradation of the radiopharmaceutical. This paper presents a model which takes the above processes into account. The model is illustrated with clinical data derived from Mo-99 contaminated radiopharmaceuticals. 5 references, 2 figures, 6 tables

Bioremediation of Uranium-Contaminated Groundwater using Engineered Injection and Extraction

Science.gov (United States)

Greene, J. A.; Neupauer, R.; Ye, M.; Kasprzyk, J. R.; Mays, D. C.; Curtis, G. P.

2017-12-01

During in-situ remediation of contaminated groundwater, a treatment chemical is injected into the contaminated groundwater to react with and degrade the contaminant, with reactions occurring where the treatment chemical contacts the contaminant. Traditional in-situ groundwater remediation relies on background groundwater flow for spreading of treatment chemicals into contaminant plumes. Engineered Injection and Extraction (EIE), in which time-varying induced flow fields are used to actively spread the treatment chemical into the contaminant plume, has been developed to increase contact between the contaminant and treatment chemical, thereby enhancing contaminant degradation. EIE has been investigated for contaminants that degrade through irreversible bimolecular reaction with a treatment chemical, but has not been investigated for a contaminant governed by reversible reactions. Uranium primarily occurs in its aqueous, mobile form, U(VI), in the environment but can be bioreduced to its sparingly soluble, immobile form, U(IV), by iron reducing bacteria stimulated by an acetate amendment. In this study, we investigate the ability of EIE to facilitate and sustain favorable conditions to immobilize uranium during remediation, and to prevent re-mobilization of uranium into the aqueous phase after active remediation has ended. Simulations in this investigation are conducted using a semi-synthetic model based on physical and chemical conditions at the Naturita Uranium Mill Tailings Remedial Action (UMTRA) site in southwestern Colorado and the Old Rifle UMTRA site in western Colorado. The EIE design is optimized for the synthetic model using the Borg multi-objective evolutionary algorithm.

On the Th internal contamination of animals

International Nuclear Information System (INIS)

Ciubotariu, M.; Danis, A.; Dumitrescu, G.

2000-01-01

Fissionable elements (U,Th) internal contamination have been studied using the fission track method as analysis method of the U and/or Th contaminant elements and Wistar-London breed rats as experiment animals. In our previous studies on the Th internal contamination, we investigated the Th biodistribution and retention in all the vital organs of the contaminated rats. In this stage, we continued this study with the Th elimination investigation through urine and excrements. The identical aliquot parts of a solution calibrated in Th, corresponding to an Annual Limit Intake, three Wistar-London breed rats were contaminated. They were kept in normal life conditions and under permanent medical surveillance up to their sacrifice. The animals were sacrificed at different time intervals after their contamination: RAT 1 = 2 days, RAT 2 = 7 days and RAT 3 = 14 days, respectively. After the sacrifice, their vital organs were sampled, weighed, calcined, re-weighed and finally analysed by track detection using the fission track micro-mappings technique. The evacuations were sampled every 24 hours: urine, on the filter paper, and all excrements balls. The samples were weighed before and after calcination and analysed in the same way as the vital organs. The Th fission track micro-mappings technique was used in the following conditions: - mica-muscovite as track detector pre-etched for fossil tracks 18 h in HF-40 per cent at room temperature; - the neutron irradiations were performed in the nuclear reactor WWR-S Bucharest at the neutron fluences of 3·10 15 - 2·10 16 fast neutrons/cm 2 ; - the visualization of the Th induced fission tracks was obtained by chemical etching in HF-40 %, 3 h at room temperature; - the Th track micromappings obtained in track detectors were studied by optical microscopy using a stereo microscope WILD M7S for ensemble study (X6-X31) and a binocular Zeiss JENA microscope for qualitative and quantitative studies (X150). The investigation of the Th

Radioactive contamination of aquatic media and organisms; La contamination radioactive des milieux et des organismes aquatiques

Energy Technology Data Exchange (ETDEWEB)

Fontaine, Y. [Commissariat a l' Energie Atomique, Saclay (France).Centre d' Etudes Nucleaires

1960-07-01

After a brief account of the radioactive wastes produced by peaceful or military uses of Atomic Industry, the author first describes a series of observations carried out 'in the field' on the extent of contamination in aquatic organisms with respect to that of the medium. The experimental studies are then analysed, with reference both to the radioisotope metabolism and to the factors and types of contamination of aquatic organisms by wastes from atomic industry. A precise experimental project is presented at the end of the paper, including almost 300 references. (author) [French] Apres une courte etude des dechets radioactifs produits par les utilisations pacifiques ou militaires de l'Industrie Atomique, l'auteur fait etat d'abord des observations effectuees 'sur le terrain' concernant l'extension de la contamination des organismes aquatiques en rapport avec celle du milieu. L'auteur analyse ensuite les etudes experimentales se rapportant aussi bien au metabolisme des radioisotopes qu'aux facteurs et aux modalites de la contamination des organismes aquatiques par les dechets de l'industrie atomique. Un projet de travail experimental precis est presente a la fin de cette revue qui comporte pres de 300 references bibliographiques. (auteur)

Detection and reduction of tungsten contamination in ion implantation processes

International Nuclear Information System (INIS)

Polignano, M.L.; Galbiati, A.; Grasso, S.; Mica, I.; Barbarossa, F.; Magni, D.

2016-01-01

In this paper, we review the results of some studies addressing the problem of tungsten contamination in implantation processes. For some tests, the implanter was contaminated by implantation of wafers with an exposed tungsten layer, resulting in critical contamination conditions. First, DLTS (deep level transient spectroscopy) measurements were calibrated to measure tungsten contamination in ion-implanted samples. DLTS measurements of tungsten-implanted samples showed that the tungsten concentration increases linearly with the dose up to a rather low dose (5 x 10 10 cm -2 ). Tungsten deactivation was observed when the dose was further increased. Under these conditions, ToF-SIMS revealed tungsten at the wafer surface, showing that deactivation was due to surface segregation. DLTS calibration could therefore be obtained in the linear dose regime only. This calibration was used to evaluate the tungsten contamination in arsenic implantations. Ordinary operating conditions and critical contamination conditions of the equipment were compared. A moderate tungsten contamination was observed in samples implanted under ordinary operating conditions. This contamination was easily suppressed by a thin screen oxide. On the contrary, implantations in critical conditions of the equipment resulted in a relevant tungsten contamination, which could be reduced but not suppressed even by a relatively thick screen oxide (up to 150 Aa). A decontamination process consisting of high dose implantations of dummy wafers was tested for its efficiency to remove tungsten and titanium contamination. This process was found to be much more effective for titanium than for tungsten. Finally, DLTS proved to be much more sensitive that TXRF (total reflection X-ray fluorescence) in detecting tungsten contamination. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Detection and reduction of tungsten contamination in ion implantation processes

Energy Technology Data Exchange (ETDEWEB)

Polignano, M.L.; Galbiati, A.; Grasso, S.; Mica, I.; Barbarossa, F.; Magni, D. [STMicroelectronics, Agrate Brianza (Italy)

2016-12-15

In this paper, we review the results of some studies addressing the problem of tungsten contamination in implantation processes. For some tests, the implanter was contaminated by implantation of wafers with an exposed tungsten layer, resulting in critical contamination conditions. First, DLTS (deep level transient spectroscopy) measurements were calibrated to measure tungsten contamination in ion-implanted samples. DLTS measurements of tungsten-implanted samples showed that the tungsten concentration increases linearly with the dose up to a rather low dose (5 x 10{sup 10} cm{sup -2}). Tungsten deactivation was observed when the dose was further increased. Under these conditions, ToF-SIMS revealed tungsten at the wafer surface, showing that deactivation was due to surface segregation. DLTS calibration could therefore be obtained in the linear dose regime only. This calibration was used to evaluate the tungsten contamination in arsenic implantations. Ordinary operating conditions and critical contamination conditions of the equipment were compared. A moderate tungsten contamination was observed in samples implanted under ordinary operating conditions. This contamination was easily suppressed by a thin screen oxide. On the contrary, implantations in critical conditions of the equipment resulted in a relevant tungsten contamination, which could be reduced but not suppressed even by a relatively thick screen oxide (up to 150 Aa). A decontamination process consisting of high dose implantations of dummy wafers was tested for its efficiency to remove tungsten and titanium contamination. This process was found to be much more effective for titanium than for tungsten. Finally, DLTS proved to be much more sensitive that TXRF (total reflection X-ray fluorescence) in detecting tungsten contamination. (copyright 2016 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Bonding of radioactive contamination. IV. Effect of surface finish

International Nuclear Information System (INIS)

Rankin, W.N.

1983-01-01

The mechanisms by which radioactive contamination would be bonded to a DWPF canister are being investigated. Previous investigations in this series have examined the effects of temperature, oxidation before contamination, and atmosphere composition control on the bonding of contamination. This memorandum describes the results of tests to determine the effect of special surface finishes on the bonding of contamination to waste glass canisters. Surface pretreatments which produce smoother canister surfaces actually cause radioactive contamination to be more tightly bonded to the metal surface than on an untreated surface. Based on the results of these tests it is recommended that the canister surface finish be specified as having a bright cold rolled mill finish equivalent to ASTM No. 2B. 7 references, 3 figures, 3 tables

Protection against radioactive contamination of food and agricultural products

International Nuclear Information System (INIS)

Szabo, A.; Kovacs, Z.

1977-01-01

Due to contaminating effects from nuclear explosions and nuclear power plants, the systematic investigation of environmental radioactive contamination is absolutely necessary. In order to reduce the artificial radiation dose to which the human body is exposed, isotope content of foods and agricultural products should be known. The authors evaluate the decontamination possibilities of food produced from vegetable and animal products, starting from the contamination of some products. For vegetable product decontamination the use of suitable fertilizers, thorough scrubbing in excess water and, for cereals, milling is proposed. As the most effective preventive measure of radiation contamination of food products of animal origin, appropriate packing is proposed. The storage and preservation problems are emphasized for short half-life radiation contamination. (P.J.)

Solidification treatment of thiophene and BTEX contaminated soils

International Nuclear Information System (INIS)

Zarlinski, S.J.; Kingham, N.W.; Blevins, J.

1995-01-01

Contamination at the McColl Superfund Site, located in Fullerton, California, is due to the disposal, in pits, of spent sulfuric acid sludge from the production of aviation fuel. A treatability study was performed to evaluate the electiveness of in situ solidification treatment of materials contaminated with high concentrations of benzene, toluene, ethylbenzene, and xylenes (BTEX), as well as thiophene and other organic compounds. The contaminated materials were extremely acidic (pH<1) and had high organic and sulfur contents of greater than 70 percent and 10 percent, respectively. A total of 150 mixtures were screened to evaluate the effectiveness of 15 reagents. Based on the preliminary screening results, six mixtures were selected as being the most effective at treating the contaminated materials. Comprehensive evaluations of the candidate mixtures included (1) quantitative glovebag volatilization studies, (2) chemical characterization of the treated materials, (3) strength characterizations at multiple cure times of up to 60 days, (4) emissions monitoring of the treated materials at cure times of 7 and 14 days, and (5) the evaluation of oxidation reagents for treatment of the thiophene contamination. The treatability study demonstrated that solidification treatment is an effective alternative for remediation of the thiophene and BTEX contaminated materials

Legionella contamination in hot water of Italian hotels.

Science.gov (United States)

Borella, Paola; Montagna, Maria Teresa; Stampi, Serena; Stancanelli, Giovanna; Romano-Spica, Vincenzo; Triassi, Maria; Marchesi, Isabella; Bargellini, Annalisa; Tatò, Daniela; Napoli, Christian; Zanetti, Franca; Leoni, Erica; Moro, Matteo; Scaltriti, Stefania; Ribera D'Alcalà, Gabriella; Santarpia, Rosalba; Boccia, Stefania

2005-10-01

A cross-sectional multicenter survey of Italian hotels was conducted to investigate Legionella spp. contamination of hot water. Chemical parameters (hardness, free chlorine concentration, and trace element concentrations), water systems, and building characteristics were evaluated to study risk factors for colonization. The hot water systems of Italian hotels were strongly colonized by Legionella; 75% of the buildings examined and 60% of the water samples were contaminated, mainly at levels of > or =10(3) CFU liter(-1), and Legionella pneumophila was the most frequently isolated species (87%). L. pneumophila serogroup 1 was isolated from 45.8% of the contaminated sites and from 32.5% of the hotels examined. When a multivariate logistic model was used, only hotel age was associated with contamination, but the risk factors differed depending on the contaminating species and serogroup. Soft water with higher chlorine levels and higher temperatures were associated with L. pneumophila serogroup 1 colonization, whereas the opposite was observed for serogroups 2 to 14. In conclusion, Italian hotels, particularly those located in old buildings, represent a major source of risk for Legionnaires' disease due to the high frequency of Legionella contamination, high germ concentration, and major L. pneumophila serogroup 1 colonization. The possible role of chlorine in favoring the survival of Legionella species is discussed.

Listeria monocytogenes contamination in dairy plants: evaluation of Listeria monocytogenes environmental contamination in two cheese-making plants using sheeps milk

Directory of Open Access Journals (Sweden)

Michela Ibba

2013-09-01

Full Text Available Listeria monocytogenes harbouring niches established in the processing plant support post-process contamination of dairy products made from pasteurised or thermised milk. The present study investigated L. monocytogenes environmental contamination in two sheep’s milk cheese-making plants. Persistence of contamination in the area at higher risk was also investigated. During a one-year survey 7 samplings were carried out in each dairy plant, along the production lines of Pecorino Romano and ricotta salata cheese. A total of 613 environmental samples collected from food contact and non-food contact surfaces were analysed according to ISO 11290-1:2005 standard method. Identification of the isolated strains was carried out by polymerase chain reaction. L. monocytogenes prevalence was 23.2% in dairy A and 13.1% in dairy B, respectively. The higher prevalence rate was found in the following areas: salting, products washing, packaging, ricotta salata storage and Pecorino Romano ripening rooms. L. monocytogenes was never found in the cheese-making area. The probability of observing samples positive for the presence of L. monocytogenes was asso- ciated with dairy plant, sampling area and the period of cheese-making (P<0.001. The greater persistence of contamination over time was observed in the washing, salting, and Pecorino Romano ripening areas. The control of persistent environmental contamination relies on the identification of L. monocytogenes niches within the processing environment and the prevention of harborage sites formation. The importance of strict cleaning and sanitising procedure in controlling L. monocytogenes environmental contamination is confirmed by the lower level of contamination observed after these procedures were correctly implemented.

Remediation of contaminated soil by cement treatment

International Nuclear Information System (INIS)

Dimovic, S.

2004-01-01

This manuscript presents the most applicable remedial technologies for contaminated soil with focus on cement stabilisation/solidification treatment. These technologies are examined in the light of soil contamination with depleted uranium in the large area of south Serbia,after Nato bombing 1999. (author) [sr

Biological processes influencing contaminant release from sediments

International Nuclear Information System (INIS)

Reible, D.D.

1996-01-01

The influence of biological processes, including bioturbation, on the mobility of contaminants in freshwater sediments is described. Effective mass coefficients are estimated for tubificid oligochaetes as a function of worm behavior and biomass density. The mass transfer coefficients were observed to be inversely proportional to water oxygen content and proportional to the square root of biomass density. The sediment reworking and contaminant release are contrasted with those of freshwater amphipods. The implications of these and other biological processes for contaminant release and i n-situ remediation of soils and sediments are summarized. 4 figs., 1 tab

Role of raptors in contaminant research

Science.gov (United States)

Henny, Charles J.

2017-01-01

This chapter reviews the history of and approaches used in studies focused on the effects of contaminants on raptors and raptor populations at the Patuxent Wildlife Research Center (Patuxent) in Laurel, MD. Worldwide raptor declines following World War II were unprecedented and resulted in a sequence of major efforts at Patuxent to understand their cause(s). The peregrine falcon (Falco peregrinus), bald eagle (Haliaeetus leucocephalus), and osprey (Pandion haliaetus) were the species of most concern in North America. Laboratory and field studies at Patuxent complemented each other and yielded timely results of national and international importance, including some findings published in the journals “Science” and “Nature.” Concern about contaminant effects on wildlife populations came to the forefront during the years immediately following World War II. This concern was worldwide and not limited to one taxonomic group or to personnel and investigations at Patuxent. Contaminant studies of raptors were only part of the story, but this review, with minor exceptions, is limited to raptor studies and the role Patuxent played in this research. Indeed, many important nonraptor contaminant studies done at Patuxent, as well as raptor studies conducted elsewhere, are not mentioned here. For other reviews of contaminant-wildlife issues in the 1950s and 1960s, the reader is referred to “Silent Spring” by Rachel Carson (1962), “Pesticides and the Living Landscape” by Robert Rudd (1964), and “Return of the Peregrine: A North American Saga of Tenacity and Teamwork” by Tom Cade and Bill Burnham (Cade and Burnham, 2003).

Quantitative risk assessment of drinking water contaminants

International Nuclear Information System (INIS)

Cothern, C.R.; Coniglio, W.A.; Marcus, W.L.

1986-01-01

The development of criteria and standards for the regulation of drinking water contaminants involves a variety of processes, one of which is risk estimation. This estimation process, called quantitative risk assessment, involves combining data on the occurrence of the contaminant in drinking water and its toxicity. The human exposure to a contaminant can be estimated from occurrence data. Usually the toxicity or number of health effects per concentration level is estimated from animal bioassay studies using the multistage model. For comparison, other models will be used including the Weibull, probit, logit and quadratic ones. Because exposure and toxicity data are generally incomplete, assumptions need to be made and this generally results in a wide range of certainty in the estimates. This range can be as wide as four to six orders of magnitude in the case of the volatile organic compounds in drinking water and a factor of four to five for estimation of risk due to radionuclides in drinking water. As examples of the differences encountered in risk assessment of drinking water contaminants, discussions are presented on benzene, lead, radon and alachlor. The lifetime population risk estimates for these contaminants are, respectively, in the ranges of: <1 - 3000, <1 - 8000, 2000-40,000 and <1 - 80. 11 references, 1 figure, 1 table

Background compensation methodologies for contamination monitoring systems

International Nuclear Information System (INIS)

Raman, Anand; Chaudhury, Probal; Pradeepkumar, K.S.

2014-01-01

Radiation surveillance program in the various nuclear facilities incorporate contamination monitoring as an important component. Contamination monitoring programs constitute monitoring for alpha and beta contamination of the physical entities associated with the working personnel that include his hands, feet, clothing, shoes as well as the general surface areas in the working environment like floors. All these measurements are fraught with the contribution of the ambient gamma background radiation fields. These inhibit a proper and precise estimation of the contamination concentration being monitored. This paper investigates the efficacy of two methodologies that have been incorporated in two of the contamination monitoring systems developed in the Division. In the first system discussed, a high degree of gamma compensation has been achieved for an uniform exposure of the order of 50 nSv/hr to 100 mSv/hr. In the second system discussed, the degree of gamma compensation achieved is equal to those dictated by the statistical nature of the uncertainties associated with the subtraction of background from the source data. These two methods can be very effectively employed depending on the application requirement. A minimum detection level equivalent to 0.37 Bq/cdm 2 has been achieved in both these cases

Treatment of contaminated waste plastics material

International Nuclear Information System (INIS)

Sims, J.; Hitchcock, J.W.

1984-01-01

Radioactive contaminated plastics material is treated by reducing it to uniform-sized debris and extruding it from a heated extruder into a sealed container in monolithic block form or as an in-fill matrix for other contaminated waste articles to create a substantially void-free sealed mass for disposal. Density adjusting fillers may be included. Extrusion may alternatively take place into a clean sealable plastics tube. (author)

30 CFR 56.5001 - Exposure limits for airborne contaminants.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Exposure limits for airborne contaminants. 56... Quality and Physical Agents Air Quality § 56.5001 Exposure limits for airborne contaminants. Except as... contaminants shall not exceed, on the basis of a time weighted average, the threshold limit values adopted by...

Bioremediation of crude oil contaminated tea plantation soil using ...

African Journals Online (AJOL)

Crude oil contamination of soil is a major concern for tea industry in Assam, India. Crude oil is a persistent organic contaminant which alters soil physical and biochemical characteristics and makes tea plants more susceptible against crude oil contamination. Therefore, two native bacterial strains designated as AS 03 and ...

CONTAMINATED SOIL VOLUME ESTIMATE TRACKING METHODOLOGY

International Nuclear Information System (INIS)

Durham, L.A.; Johnson, R.L.; Rieman, C.; Kenna, T.; Pilon, R.

2003-01-01

The U.S. Army Corps of Engineers (USACE) is conducting a cleanup of radiologically contaminated properties under the Formerly Utilized Sites Remedial Action Program (FUSRAP). The largest cost element for most of the FUSRAP sites is the transportation and disposal of contaminated soil. Project managers and engineers need an estimate of the volume of contaminated soil to determine project costs and schedule. Once excavation activities begin and additional remedial action data are collected, the actual quantity of contaminated soil often deviates from the original estimate, resulting in cost and schedule impacts to the project. The project costs and schedule need to be frequently updated by tracking the actual quantities of excavated soil and contaminated soil remaining during the life of a remedial action project. A soil volume estimate tracking methodology was developed to provide a mechanism for project managers and engineers to create better project controls of costs and schedule. For the FUSRAP Linde site, an estimate of the initial volume of in situ soil above the specified cleanup guidelines was calculated on the basis of discrete soil sample data and other relevant data using indicator geostatistical techniques combined with Bayesian analysis. During the remedial action, updated volume estimates of remaining in situ soils requiring excavation were calculated on a periodic basis. In addition to taking into account the volume of soil that had been excavated, the updated volume estimates incorporated both new gamma walkover surveys and discrete sample data collected as part of the remedial action. A civil survey company provided periodic estimates of actual in situ excavated soil volumes. By using the results from the civil survey of actual in situ volumes excavated and the updated estimate of the remaining volume of contaminated soil requiring excavation, the USACE Buffalo District was able to forecast and update project costs and schedule. The soil volume

Passive sampling methods for contaminated sediments: State of the science for organic contaminants

Science.gov (United States)

Lydy, Michael J; Landrum, Peter F; Oen, Amy MP; Allinson, Mayumi; Smedes, Foppe; Harwood, Amanda D; Li, Huizhen; Maruya, Keith A; Liu, Jingfu

2014-01-01

This manuscript surveys the literature on passive sampler methods (PSMs) used in contaminated sediments to assess the chemical activity of organic contaminants. The chemical activity in turn dictates the reactivity and bioavailability of contaminants in sediment. Approaches to measure specific binding of compounds to sediment components, for example, amorphous carbon or specific types of reduced carbon, and the associated partition coefficients are difficult to determine, particularly for native sediment. Thus, the development of PSMs that represent the chemical activity of complex compound–sediment interactions, expressed as the freely dissolved contaminant concentration in porewater (Cfree), offer a better proxy for endpoints of concern, such as reactivity, bioaccumulation, and toxicity. Passive sampling methods have estimated Cfree using both kinetic and equilibrium operating modes and used various polymers as the sorbing phase, for example, polydimethylsiloxane, polyethylene, and polyoxymethylene in various configurations, such as sheets, coated fibers, or vials containing thin films. These PSMs have been applied in laboratory exposures and field deployments covering a variety of spatial and temporal scales. A wide range of calibration conditions exist in the literature to estimate Cfree, but consensus values have not been established. The most critical criteria are the partition coefficient between water and the polymer phase and the equilibrium status of the sampler. In addition, the PSM must not appreciably deplete Cfree in the porewater. Some of the future challenges include establishing a standard approach for PSM measurements, correcting for nonequilibrium conditions, establishing guidance for selection and implementation of PSMs, and translating and applying data collected by PSMs. Integr Environ Assess Manag 2014;10:167–178. © 2014 The Authors. Integrated Environmental Assessment and Management published by Wiley Periodicals, Inc. on behalf of

Plutonium contaminated materials research programme

International Nuclear Information System (INIS)

Higson, S.G.

1986-01-01

The paper is a progress report for 1985 from the Plutonium Contaminated Materials Working Party (PCMWP). The PCMWP co-ordinates research and development on a national basis in the areas of management, treatment and immobilisation of plutonium contaminated materials, for the purpose of waste management. The progress report contains a review of the development work carried out in eight areas, including: reduction of arisings, plutonium measurement, sorting and packaging, washing of shredded combustible PCM, decommissioning and non-combustible PCM treatment, PCM immobilisation, treatment of alpha bearing liquid wastes, and engineering objectives. (UK)

Analysis of surface contaminants on beryllium and aluminum windows

International Nuclear Information System (INIS)

Gmur, N.F.

1987-06-01

An effort has been made to document the types of contamination which form on beryllium window surfaces due to interaction with a synchrotron radiation beam. Beryllium windows contaminated in a variety of ways (exposure to water and air) exhibited surface powders, gels, crystals and liquid droplets. These contaminants were analyzed by electron diffraction, electron energy loss spectroscopy, energy dispersive x-ray spectroscopy and wet chemical methods. Materials found on window surfaces include beryllium oxide, amorphous carbon, cuprous oxide, metallic copper and nitric acid. Aluminum window surface contaminants were also examined

Environmental restoration and biological contamination: ecological and legal aspects

Directory of Open Access Journals (Sweden)

Ademir Reis

2005-05-01

Full Text Available Environmental restoration is a pressing current need. However, protected areas have been exposed to biological contamination risks because the traditional techniques of restoration frequently use exotic species. This causes some concern, since biological contamination is the second major cause of species extinction in the world. It is important to use only native species in restoration projects in order to promote an effective environmental restoration without the risk of contamination. This paper discusses some issues concerning environmental restoration, biological contamination and the need for clearer laws.

Relationship between rainfall and microbiological contamination of ...

African Journals Online (AJOL)

Outbreaks of contamination events in many developing countries occur during periods of peak rainfall. This study presents evidence of direct pulse response of shallow groundwater contamination events to rainfall in Northern Mozambique. The objective of the paper is to establish both a statistical relationship between ...

Total aflatoxin, fumonisin and deoxynivalenol contamination of ...

African Journals Online (AJOL)

Mycotoxin contamination is a common problem in developing countries, particularly in cereals, and this poses a serious health risk to its consumers. Busaa is a Kenyan traditional brew whose cereal ingredients are prone to mycotoxin contamination. This study aimed at detecting the presence and subsequently quantifying ...

Microbial Functional Gene Diversity Predicts Groundwater Contamination and Ecosystem Functioning

Science.gov (United States)

Zhang, Ping; Wu, Linwei; Rocha, Andrea M.; Shi, Zhou; Wu, Bo; Qin, Yujia; Wang, Jianjun; Yan, Qingyun; Curtis, Daniel; Ning, Daliang; Van Nostrand, Joy D.; Wu, Liyou; Watson, David B.; Adams, Michael W. W.; Alm, Eric J.; Adams, Paul D.; Arkin, Adam P.

2018-01-01

ABSTRACT Contamination from anthropogenic activities has significantly impacted Earth’s biosphere. However, knowledge about how environmental contamination affects the biodiversity of groundwater microbiomes and ecosystem functioning remains very limited. Here, we used a comprehensive functional gene array to analyze groundwater microbiomes from 69 wells at the Oak Ridge Field Research Center (Oak Ridge, TN), representing a wide pH range and uranium, nitrate, and other contaminants. We hypothesized that the functional diversity of groundwater microbiomes would decrease as environmental contamination (e.g., uranium or nitrate) increased or at low or high pH, while some specific populations capable of utilizing or resistant to those contaminants would increase, and thus, such key microbial functional genes and/or populations could be used to predict groundwater contamination and ecosystem functioning. Our results indicated that functional richness/diversity decreased as uranium (but not nitrate) increased in groundwater. In addition, about 5.9% of specific key functional populations targeted by a comprehensive functional gene array (GeoChip 5) increased significantly (P contamination and ecosystem functioning. This study indicates great potential for using microbial functional genes to predict environmental contamination and ecosystem functioning. PMID:29463661

Geotechnical properties of oil-contaminated Kuwaiti sand

Energy Technology Data Exchange (ETDEWEB)

Al-Sanad, H.A.; Eid, W.K.; Ismael, N.F. [Kuwait Univ., Safat (Kuwait). Dept. of Civil Engineering

1995-05-01

Large quantities of oil-contaminated sands resulted from exploded oil wells, burning oil fires, the destruction of oil storage tanks, and the formation of oil lakes in Kuwait at the end of the Gulf War. An extensive laboratory testing program was carried out to determine the geotechnical characteristics of this material. Testing included basic properties, compaction and permeability tests, and triaxial and consolidation tests on clean and contaminated sand at the same relative density. Contaminated specimens were prepared by mixing the sand with oil in the amount of 6% by weight or less to match field conditions. The influence of the type of oil, and relative density was also investigated by direct shear tests. The results indicated a small reduction in strength and permeability and an increase in compressibility due to contamination. The preferred method of disposal of this material is to use it as a stabilizing material for other projects such as road construction.

Geotechnical properties of oil-contaminated Kuwaiti sand

International Nuclear Information System (INIS)

Al-Sanad, H.A.; Eid, W.K.; Ismael, N.F.

1995-01-01

Large quantities of oil-contaminated sands resulted from exploded oil wells, burning oil fires, the destruction of oil storage tanks, and the formation of oil lakes in Kuwait at the end of the Gulf War. An extensive laboratory testing program was carried out to determine the geotechnical characteristics of this material. Testing included basic properties, compaction and permeability tests, and triaxial and consolidation tests on clean and contaminated sand at the same relative density. Contaminated specimens were prepared by mixing the sand with oil in the amount of 6% by weight or less to match field conditions. The influence of the type of oil, and relative density was also investigated by direct shear tests. The results indicated a small reduction in strength and permeability and an increase in compressibility due to contamination. The preferred method of disposal of this material is to use it as a stabilizing material for other projects such as road construction

Screening of plants for phytoremediation of oil-contaminated soil.

Science.gov (United States)

Ikeura, Hiromi; Kawasaki, Yu; Kaimi, Etsuko; Nishiwaki, Junko; Noborio, Kosuke; Tamaki, Masahiko

2016-01-01

Several species of ornamental flowering plants were evaluated regarding their phytoremediation ability for the cleanup of oil-contaminated soil in Japanese environmental conditions. Thirty-three species of plants were grown in oil-contaminated soil, and Mimosa, Zinnia, Gazania, and cypress vine were selected for further assessment on the basis of their favorable initial growth. No significant difference was observed in the above-ground and under-ground dry matter weight of Gazania 180 days after sowing between contaminated and non-contaminated plots. However, the other 3 species of plants died by the 180th day, indicating that Gazania has an especially strong tolerance for oil-contaminated soil. The total petroleum hydrocarbon concentration of the soils in which the 4 species of plants were grown decreased by 45-49% by the 180th day. Compared to an irrigated plot, the dehydrogenase activity of the contaminated soil also increased significantly, indicating a phytoremediation effect by the 4 tested plants. Mimosa, Zinnia, and cypress vine all died by the 180th day after seeding, but the roots themselves became a source of nutrients for the soil microorganisms, which led to a phytoremediation effect by increase in the oil degradation activity. It has been indicated that Gazania is most appropriate for phytoremediation of oil-contaminated soil.

30 CFR 57.5001 - Exposure limits for airborne contaminants.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Exposure limits for airborne contaminants. 57... Underground § 57.5001 Exposure limits for airborne contaminants. Except as permitted by § 57.5005— (a) Except as provided in paragraph (b), the exposure to airborne contaminants shall not exceed, on the basis of...

Electrical Tracking Formation on Silane Epoxy Resin under Various Contaminants

Directory of Open Access Journals (Sweden)

NFN Rochmadi

2013-03-01

Full Text Available Contamination at the surface of the insulator becomes a serious problem in power system operation, especially for the tropical area. Humidity and rainfall play an important role in wetness by the water at the surface of the insulator, which result in the presence of contaminant and leakage current flowing at the surface of the insulator. This leakage current will generate heat which occurs at the surface of an insulator, so that dry band area will be formed. This ultimately leads to flashover. This paper presents the influence of contaminants to leakage current and formation of electrical tracking at the surface of epoxy resin compound wit silicon rubber. The test was based on Inclined-Planed Tracking method with NH4Cl as contaminants. The industrial and coastal contaminants are used to explain the effect of contaminant at surface tracking process. The flow rate of contaminant was 0.3 ml/min. The 3.5 kV AC high voltage 50 Hz was applied to the top electrodes. It is found that industrial contamination resulting in the smallest surface leakage current is 327.6 mA. Also it is found that coastal contaminant (1420 mS/cm showed the severest damage at surface of test sample. Therefore, special treatment of the sample are needed under these conditions so that the material performance can be improved, especially against the electrical tracking.

Life Support Systems: Trace Contaminant and Particulate Control

Data.gov (United States)

National Aeronautics and Space Administration — Advanced Exploration Systems (AES) Life Support Systems project Trace Contaminant and Particulate Control task: Work in the area of trace contamination and...

Hydrodebridement of wounds: effectiveness in reducing wound bacterial contamination and potential for air bacterial contamination.

Science.gov (United States)

Bowling, Frank L; Stickings, Daryl S; Edwards-Jones, Valerie; Armstrong, David G; Boulton, Andrew Jm

2009-05-08

The purpose of this study was to assess the level of air contamination with bacteria after surgical hydrodebridement and to determine the effectiveness of hydro surgery on bacterial reduction of a simulated infected wound. Four porcine samples were scored then infected with a broth culture containing a variety of organisms and incubated at 37 degrees C for 24 hours. The infected samples were then debrided with the hydro surgery tool (Versajet, Smith and Nephew, Largo, Florida, USA). Samples were taken for microbiology, histology and scanning electron microscopy pre-infection, post infection and post debridement. Air bacterial contamination was evaluated before, during and after debridement by using active and passive methods; for active sampling the SAS-Super 90 air sampler was used, for passive sampling settle plates were located at set distances around the clinic room. There was no statistically significant reduction in bacterial contamination of the porcine samples post hydrodebridement. Analysis of the passive sampling showed a significant (p air whilst using hydro surgery equipment compared with a basal count of 582 CFUs/m3. During removal of the wound dressing, a significant increase was observed relative to basal counts (p air samples was still significantly raised 1 hour post-therapy. The results suggest a significant increase in bacterial air contamination both by active sampling and passive sampling. We believe that action might be taken to mitigate fallout in the settings in which this technique is used.

Method of producing hydrogen, and rendering a contaminated biomass inert

Science.gov (United States)

Bingham, Dennis N [Idaho Falls, ID; Klingler, Kerry M [Idaho Falls, ID; Wilding, Bruce M [Idaho Falls, ID

2010-02-23

A method for rendering a contaminated biomass inert includes providing a first composition, providing a second composition, reacting the first and second compositions together to form an alkaline hydroxide, providing a contaminated biomass feedstock and reacting the alkaline hydroxide with the contaminated biomass feedstock to render the contaminated biomass feedstock inert and further producing hydrogen gas, and a byproduct that includes the first composition.

Contamination measurements on persons after a nuclear accident

International Nuclear Information System (INIS)

Maushart, R.

1992-01-01

The purpose of contamination measurements after accidents is threefold: to detect and localize contaminations; to determine the level of contamination as a base for medical decisions; and to check the scope and efficiency of the decontamination measures. Persons involved in accidents should never measure their contamination themselves. The radiation protection personnel, whether it belongs to the medical team or to the disaster control squads, must be familiar with the measuring instruments and experienced in handling these instruments. A high priority has to be placed on training and constant practice. The monitors used must meet the special requirements of an emergency situation. This includes resistance against environmental factors - temperature, humidity, vibrations - as well as the simplicity of handling the instrument, and the clear presentation of the results. (author)

Temporal sealing material of tritium-contaminated stainless steel

International Nuclear Information System (INIS)

Wen Wei; Dan Guiping; Zhang Dong; Qiu Yongmei; Zhang Li

2010-01-01

Tritium can be released from the exterior of tritium-contaminated stainless steel by slight stirring while decontaminating and disassembling. In order to avoid secondary tritium contamination to environment and operators, it is necessary to cover with an effective coating to tritium on the exterior of tritium-contaminated stainless steel and fill an effective substance to tritium inside. The results of tritium sealed experiments show that sealing efficiency of neutral silicone rubber is more than 85% for condition of static state and more than 99% for foam concrete condition of dynamic state. Neutral silicone rubber and foam concrete which have finer sealing efficiency can be used as temporal sealed material for the decontamination and disassembly of tritium-contaminated stainless steel. (authors)

Toxicity of lead-contaminated sediment to mute swans

Science.gov (United States)

Day, D.D.; Beyer, W.N.; Hoffman, D.J.; Morton, Alexandra; Sileo, L.; Audet, D.J.; Ottinger, M.A.

2003-01-01

Most ecotoxicological risk assessments of wildlife emphasize contaminant exposure through ingestion of food and water. However, the role of incidental ingestion of sediment-bound contaminants has not been adequately appreciated in these assessments. This study evaluates the toxicological consequences of contamination of sediments with metals from hard-rock mining and smelting activities. Lead-contaminated sediments collected from the Coeur d'Alene River Basin in Idaho were combined with either a commercial avian maintenance diet or ground rice and fed to captive mute swans (Cygnus olor) for 6 weeks. Experimental treatments consisted of maintenance or rice diets containing 0, 12 (no rice group), or 24% highly contaminated (3,950 ug/g lead) sediment or 24% reference (9.7 ug/g lead) sediment. Although none of the swans died, the group fed a rice diet containing 24% lead-contaminated sediment were the most severely affected, experiencing a 24% decrease in mean body weight, including three birds that became emaciated. All birds in this treatment group had nephrosis; abnormally dark, viscous bile; and significant (p < 0.05) reductions in hematocrit and hemoglobin concentrations compared to their pretreatment levels. This group also had the greatest mean concentrations of lead in blood (3.2 ug/g), brain (2.2 ug/g), and liver (8.5 ug/g). These birds had significant (alpha = 0.05) increases in mean plasma alanine aminotransferase activity, cholesterol, and uric acid concentrations and decreased plasma triglyceride concentrations compared to all other treatment groups. After 14 days of exposure, mean protoporphyrin concentrations increased substantially, and mean delta-aminolevulinic acid dehydratase activity decreased by more than 95% in all groups fed diets containing highly contaminated sediments. All swans fed diets that contained 24% lead-contaminated sediment had renal acid-fast intranuclear inclusion bodies, which are diagnostic of lead poisoning in waterfowl. Body

Implementation and planning of preventive and multi-layered contaminated water treatment

International Nuclear Information System (INIS)

Takahashi, Takeshi; Arai, Tomoyuki

2014-01-01

In Fukushima Daiichi D and D activities, one of the most challenging issues is contaminated water management. In order to control ground water inflow into the buildings so that amount of contaminated water does not increase and prevent contaminated water spread out to the environment including into the ocean, TEPCO are taking various measures: In order to remove contamination sources, the removal of the highly contaminated water in the seaside trenches are being implemented. And also, the acceleration of water purification is planned by contaminated water clean-up facility. For the purpose of Isolating water from contaminated sources, construction of the frozen-soil land-side wall started in order to prevent the groundwater from flowing in the area and contaminated water from flowing out from the area. In order to prevent leakage of contaminated water into the ocean, soil improvement with sodium silicate (liquid glass) and Installation of the sea-side impermeable walls are implemented. Furthermore, replacement of the flange-type tanks with welded-joint tanks to mitigate leakage risks is underway. (author)

Environmental radioactive contamination and its control for nuclear power plants

International Nuclear Information System (INIS)

Shi Zhongqi; Qu Jingyuan; Cui Yongli

1998-01-01

The environmental radioactive releases and exposure to human being due to operation of nuclear power plants in the world and in China, environmental contamination and consequences caused by severe nuclear power plant accidents in the history, control of the radioactive contamination in China, and some nuclear laws on the radioactive contamination control established by international organizations and USA etc. are described according to literature investigation and research. Some problems and comments in radioactive contamination control for nuclear power plants in China are presented. Therefore, perfecting laws and regulations and enhancing surveillances on the contamination control are recommended

The design of hands and feet contamination monitor

International Nuclear Information System (INIS)

Song Jiangxue; Shen Yang; Deng Changming; Zhang Jia; Hou Lei; Meng Dan

2011-01-01

In order to protect the hands and feet of personnel engaged in nuclear, draw on advanced hands and feet contamination monitor, we design a new radiation protection instrumentation. It describes the composition of the hands and feet contamination monitor, and software program design. It describes the hardware monitor software, firmware and computer programming techniques. If device found your hand and foot surface is contamination, it will prompt you to decontamination, to protect your hands and feet of safety. (authors)

Detection of contamination of municipal water distribution systems

Science.gov (United States)

Cooper, John F [Oakland, CA

2012-01-17

A system for the detection of contaminates of a fluid in a conduit. The conduit is part of a fluid distribution system. A chemical or biological sensor array is connected to the conduit. The sensor array produces an acoustic signal burst in the fluid upon detection of contaminates in the fluid. A supervisory control system connected to the fluid and operatively connected to the fluid distribution system signals the fluid distribution system upon detection of contaminates in the fluid.

Assessment and Remediation of Lead Contamination in Senegal

OpenAIRE

Donald E. Jones, MS; Assane Diop, BS; Meredith Block, MPA; Alexander Smith-Jones, BS; Andrea Smith-Jones, MS

2011-01-01

Background. This paper describes the impact of improper used lead-acid battery (ULAB) handling and disposal. A specific case study is presented describing the field assessment and remediation of lead contamination in a community in Senegal where at least 18 children died from lead poisoning. Objectives. The assessment and remediation process utilized to address the Senegal lead contamination has been used as a model approach to solving used lead-acid battery (ULAB) contamination in other e...

Electro kinetic remediation of contaminated habitats | Shenbagavalli ...

African Journals Online (AJOL)

Electrokinetics (EK) is a process that separates and extracts heavy metals, radionuclides and organic contaminants from saturated or unsaturated soils, sludge, and sediments. A low intensity direct current is applied across electrode pairs that have been implanted in the ground on each side of the contaminated soil mass.

Remediation of soil contaminated with polycyclic aromatic ...

African Journals Online (AJOL)

user

2011-02-14

Feb 14, 2011 ... The aim of this study was to determine ways of remediating soils contaminated with polycyclic aromatic hydrocarbons (PAHs) associated with crude oil. The study involves the use of planted cowpeas, mushrooms, algae, dead vegetable and live earthworm, and fire-heating of the contaminated garden soil ...

Spectral characterization of soil and coal contamination on snow

Indian Academy of Sciences (India)

Snow is a highly reflecting object found naturally on the Earth and its albedo is highly influenced by the amount and type of contamination. In the present study, two major types of contaminants (soil and coal) have been used to understand their effects on snow reflectance in the Himalayan region. These contaminants were ...

Evaluation of the internal contamination risk for isotope laboratory workers

International Nuclear Information System (INIS)

Adamiak-Ziemba, J.; Doniec, J.; Kocznow, W.; Hawrynski, M.

1985-01-01

The investigation covered 484 workers. Altogether 1787 determinations have been made, in this - 1648 internal contaminations and 139 contaminations of air, hand skin and working surfaces. The internal contaminations (22% of results) resulted mainly from deviation from radiological protection rules and were reduced by certain changes. Those were tritium contaminations (application of tritium radioluminescence dyes) and 125, 131 J. The highest levels of which were 20 mSv and 0.25% ALI respectively. The results of 238 Pu air contamination measurements indicates that the dust arising during the production of smoke detectors (with 238 PuO 2 sources) probably has no respirable fraction properties, what confines its absorption in lower parts of the respiratory tract. It has been demonstrated that in Poland is no need of a central system of permanent internal contamination control. (author)

Total effective dose equivalent associated with fixed uranium surface contamination

International Nuclear Information System (INIS)

Bogard, J.S.; Hamm, R.N.; Ashley, J.C.; Turner, J.E.; England, C.A.; Swenson, D.E.; Brown, K.S.

1997-04-01

This report provides the technical basis for establishing a uranium fixed-contamination action level, a fixed uranium surface contamination level exceeding the total radioactivity values of Appendix D of Title 10, Code of Federal Regulations, part 835 (10CFR835), but below which the monitoring, posting, and control requirements for Radiological Areas are not required for the area of the contamination. An area of fixed uranium contamination between 1,000 dpm/100 cm 2 and that level corresponding to an annual total effective dose equivalent (TEDE) of 100 mrem requires only routine monitoring, posting to alert personnel of the contamination, and administrative control. The more extensive requirements for monitoring, posting, and control designated by 10CFR835 for Radiological Areas do not have to be applied for these intermediate fixed-contamination levels

Radioactive contamination: atlas France and Europe. French soils contamination by Chernobyl accident fallouts - The lie evidences

International Nuclear Information System (INIS)

Paris, Andre; Castanier, Corinne

2002-01-01

This document deals with the Chernobyl nuclear accident impacts and the authorities transparency. The first part is a reference document constituted by the CRIIRAD and showing how the authorities strove for minimizing the real contamination of French soils by the Chernobyl fallouts. In the second part, an atlas provides the detailed maps of the radioactive contamination of soils based on more than 3000 measurements carried out by a geologist, Andre Paris, assisted by the CRIIRAD laboratory

Centrifuge modelling of contaminant transport processes

OpenAIRE

Culligan, P. J.; Savvidou, C.; Barry, D. A.

1996-01-01

Over the past decade, research workers have started to investigate problems of subsurface contaminant transport through physical modelling on a geotechnical centrifuge. A major advantage of this apparatus is its ability to model complex natural systems in a controlled laboratory environment In this paper, we discusses the principles and scaling laws related to the centrifugal modelling of contaminant transport, and presents four examples of recent work that has bee...