Container for radioactive materials

International Nuclear Information System (INIS)

Housholder, W.R.; Greer, N.L.

1976-01-01

The improvement of the construction of containers for the transport of nuclear fuels is proposed where above all, the insulating mass suggested is important as it acts as a safeguard in case of an accident. The container consists of a metal casing in which there is a pressure boiler and a gamma-shielding device, spacers between the metal casing and the shielding device as well as an insulation filling the space between them. The insulating material is a water-in-resin emulsion which is hardened or cross-linked by peroxide and which can furthermore contain up to 50 wt.% solid silicious material such as vermuculite or chopped glass fibre. The construction and variations of the insulating mass composition are described in great detail. (HR) [de

Materials for high-level waste containment

International Nuclear Information System (INIS)

Marsh, G.P.

1982-01-01

The function of the high-level radioactive waste container in storage and of a container/overpack combination in disposal is considered. The consequent properties required from potential fabrication materials are discussed. The strategy adopted in selecting containment materials and the experimental programme underway to evaluate them are described. (U.K.)

Standard Practice for Laboratory Screening of Metallic Containment Materials for Use With Liquids in Solar Heating and Cooling Systems

CERN Document Server

American Society for Testing and Materials. Philadelphia

1980-01-01

1.1 This practice covers several laboratory test procedures for evaluating corrosion performance of metallic containment materials under conditions similar to those that may occur in solar heating and cooling systems. All test results relate to the performance of the metallic containment material only as a part of a metal/fluid pair. Performance in these laboratory test procedures, taken by itself, does not necessarily constitute an adequate basis for acceptance or rejection of a particular metal/fluid pair in solar heating and cooling systems, either in general or in a particular design. This practice is not intended to preclude the use of other screening tests, particularly when those tests are designed to more closely simulate field service conditions. 1.2 This practice describes apparatus and procedures for several tests, any one or more of which may be used to evaluate the deterioration of the metallic containment material in a metal/fluid pair. The procedures are designed to permit simulation, heating...

Remote container monitoring and surveillance systems

International Nuclear Information System (INIS)

Resnik, W.M.; Kadner, S.P.

1995-01-01

Aquila Technologies Group is developing a monitoring and surveillance system to monitor containers of nuclear materials. The system will both visually and physically monitor the containers. The system is based on the combination of Aquila's Gemini All-Digital Surveillance System and on Aquila's AssetLAN trademark asset tracking technology. This paper discusses the Gemini Digital Surveillance system as well as AssetLAN technology. The Gemini architecture with emphasis on anti-tamper security features is also described. The importance of all-digital surveillance versus other surveillance methods is also discussed. AssetLAN trademark technology is described, emphasizing the ability to continually track containers (as assets) by location utilizing touch memory technology. Touch memory technology provides unique container identification, as well as the ability to store and retrieve digital information on the container. This information may relate to container maintenance, inspection schedules, and other information. Finally, this paper describes the combination of the Gemini system with AssetLAN technology, yielding a self contained, container monitoring and area/container surveillance system. Secure container fixture design considerations are discussed. Basic surveillance review functions are also discussed

Molten material-containing vessel

International Nuclear Information System (INIS)

Akagawa, Katsuhiko

1998-01-01

The molten material-containing vessel of the present invention comprises a vessel main body having an entrance opened at the upper end, a lid for closing the entrance, an outer tube having an upper end disposed at the lower surface of the lid, extended downwardly and having an closed lower end and an inner tube disposed coaxially with the outer tube. When a molten material is charged from the entrance to the inside of the vessel main body of the molten material-containing vessel and the entrance is closed by the lid, the outer tube and the inner tube are buried in the molten material in the vessel main body, accordingly, a fluid having its temperature elevated by absorption of the heat of the molten material rises along the inner circumferential surface of the outer tube, abuts against the lower surface of the lid and cooled by exchanging heat with the lid and forms a circulating flow. Since the heat in the molten material is continuously absorbed by the fluid, transferred to the lid and released from the lid to the atmospheric air, heat releasing efficiency can be improved compared with conventional cases. (N.H.)

Corrosion aspects of steel radioactive waste containers in cementitious materials

International Nuclear Information System (INIS)

Smart, Nick

2012-01-01

Nick Smart from Serco, UK, gave an overview of the effects of cementitious materials on the corrosion of steel during storage and disposal of various low- and intermediate-level radioactive wastes. Steel containers are often used as an overpack for the containment of radioactive wastes and are routinely stored in an open atmosphere. Since this is an aerobic and typically humid environment, the steel containers can start to corrode whilst in storage. Steel containers often come into contact with cementitious materials (e.g. grout encapsulants, backfill). An extensive account of different steel container designs and of steel corrosion mechanisms was provided. Steel corrosion rates under conditions buffered by cementitious materials have been evaluated experimentally. The main conclusion was that the cementitious environment generally facilitates the passivation of steel materials. Several general and localised corrosion mechanisms need to be considered when evaluating the performance of steel containers in cementitious environments, and environmental thresholds can be defined and used with this aim. In addition, the consequences of the generation of gaseous hydrogen by the corrosion of carbon steel under anoxic conditions must be taken into account. Discussion of the paper included: Is crevice corrosion really significant in cementitious systems? Crevice corrosion is unlikely in the cementitious backfill considered because it will tend to neutralise any acidic conditions in the crevice. What is the role of microbially-induced corrosion (MIC) in cementitious systems? Microbes are likely to be present in a disposal facility but their effect on corrosion is uncertain

Direct vitrification of plutonium-containing materials (PCM`s) with the glass material oxidation and dissolution system (GMODS)

Energy Technology Data Exchange (ETDEWEB)

Forsberg, C.W. Beahm, E.C.; Parker, G.W.; Rudolph, J.C.; Haas, P.A.; Malling, G.F.; Elam, K.; Ott, L.

1995-10-30

The end of the cold war has resulted in excess PCMs from nuclear weapons and associated production facilities. Consequently, the US government has undertaken studies to determine how best to manage and dispose of this excess material. The issues include (a) ensurance of domestic health, environment, and safety in handling, storage, and disposition, (b) international arms control agreements with Russia and other countries, and (c) economics. One major set of options is to convert the PCMs into glass for storage or disposal. The chemically inert characteristics of glasses make them a desirable chemical form for storage or disposal of radioactive materials. A glass may contain only plutonium, or it may contain plutonium along with other radioactive materials and nonradioactive materials. GMODS is a new process for the direct conversion of PCMs (i.e., plutonium metal, scrap, and residues) to glass. The plutonium content of these materials varies from a fraction of a percent to pure plutonium. GMODS has the capability to also convert other metals, ceramics, and amorphous solids to glass, destroy organics, and convert chloride-containing materials into a low-chloride glass and a secondary clean chloride salt strewn. This report is the initial study of GMODS for vitrification of PCMs as input to ongoing studies of plutonium management options. Several tasks were completed: initial analysis of process thermodynamics, initial flowsheet analysis, identification of equipment options, proof-of-principle experiments, and identification of uncertainties.

Preliminary Study of Applying Phase Change Materials (PCM) for Containment Passive Cooling

International Nuclear Information System (INIS)

Ko, A Reum; Lee, Jeong Ik; Yoon, Ho Joon

2016-01-01

Most of Pressurized Water Reactor (PWR) containments use fan cooler systems and containment spray systems. However, the importance of passive safety system has increased after the Fukushima accident. As the main passive safety system, Passive Containment Cooling System (PCCS), which utilizes natural phenomena to remove the heat released from the reactor, is suggested in the advanced pressurized water reactor (APWR). To increase the efficiency of passive cooling, additional passive containment cooling method using Phase Change Material (PCM) is suggested in this paper. For containment using PCMs, there are many advantages. Phase Change Material (PCM) is proposed as an additional passive containment cooling method to increase the efficiency of passive cooling in this paper. To apply proper PCMs to containment, commercially available PCMs were screened while reviewing thermophysical properties data and suggested selection criteria. A sensitivity study was also carried out to identify the effect of potential installation location of PCM using the CAP code. The pressure of containment in most cases showed slightly higher than that of the initial case. For the temperature of steam and water and humidity, similar results with the initial case were showed in most cases

Preliminary Study of Applying Phase Change Materials (PCM) for Containment Passive Cooling

Energy Technology Data Exchange (ETDEWEB)

Ko, A Reum; Lee, Jeong Ik [KAIST, Daejeon (Korea, Republic of); Yoon, Ho Joon [KUSTAR, Abu Dhabi (United Arab Emirates)

2016-05-15

Most of Pressurized Water Reactor (PWR) containments use fan cooler systems and containment spray systems. However, the importance of passive safety system has increased after the Fukushima accident. As the main passive safety system, Passive Containment Cooling System (PCCS), which utilizes natural phenomena to remove the heat released from the reactor, is suggested in the advanced pressurized water reactor (APWR). To increase the efficiency of passive cooling, additional passive containment cooling method using Phase Change Material (PCM) is suggested in this paper. For containment using PCMs, there are many advantages. Phase Change Material (PCM) is proposed as an additional passive containment cooling method to increase the efficiency of passive cooling in this paper. To apply proper PCMs to containment, commercially available PCMs were screened while reviewing thermophysical properties data and suggested selection criteria. A sensitivity study was also carried out to identify the effect of potential installation location of PCM using the CAP code. The pressure of containment in most cases showed slightly higher than that of the initial case. For the temperature of steam and water and humidity, similar results with the initial case were showed in most cases.

Container corporation: The financial, management, and operating implications of a universal beverage container recovery system: Executive summary

Energy Technology Data Exchange (ETDEWEB)

1991-01-01

This report contains an overview of the system. It discusses containers and container materials, elements of the system, and the container recovery cost structure. It includes a financial evaluation and addresses issues of implementation.

Storage chamber for container of radiation-contaminated material

International Nuclear Information System (INIS)

Takakura, Masahide.

1996-01-01

The present invention concerns a storage chamber for containing radiation-contaminated materials in containing tubes and having cooling fluids circulated at the outer side of the containing tubes. The storage chamber comprises a gas supply means connected to the inside of the container tube for supplying a highly heat-conductive gas and a gas exhaustion means for discharging the gas present in the container tube. When containing vessels for radiation-contaminated materials are contained in the container tube, the gases present inside of the container tube is exhausted by means of the gas exhaustion means, and highly heat conductive gases are filled from the gas supply means to the space between the container tube and the containing vessels for the radiation-contaminated materials. When the temperature of the highly heat conductive gas is elevated due to the heat generation of the radiation-contaminated materials, the container tube is heated, and then cooled by the cooling fluid at the outer side of the container tube. In this case, the heat of the radiation-contaminated material-containing vessels is removed by the heat conduction by the highly heat conductive gas to reduce temperature gradient between the containing vessels and the containing tube. This can enhance the cooling effect. (T.M.)

Radioactive Material Containment Bags

National Research Council Canada - National Science Library

2000-01-01

The audit was requested by Senator Joseph I. Lieberman based on allegations made by a contractor, Defense Apparel Services, about the Navy's actions on three contracts for radioactive material containment bags...

30 CFR 56.16004 - Containers for hazardous materials.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Containers for hazardous materials. 56.16004 Section 56.16004 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Storage and Handling § 56.16004 Containers for hazardous materials. Containers holding hazardous materials...

30 CFR 57.16004 - Containers for hazardous materials.

Science.gov (United States)

2010-07-01

... 30 Mineral Resources 1 2010-07-01 2010-07-01 false Containers for hazardous materials. 57.16004 Section 57.16004 Mineral Resources MINE SAFETY AND HEALTH ADMINISTRATION, DEPARTMENT OF LABOR METAL AND... Storage and Handling § 57.16004 Containers for hazardous materials. Containers holding hazardous materials...

Material containment enclosure

International Nuclear Information System (INIS)

Carlson, D.O.

1993-01-01

An isolation enclosure and a group of isolation enclosures are described which are useful when a relatively large containment area is required. The enclosure is in the form of a ring having a section removed so that a technician may enter the center area of the ring. In a preferred embodiment, an access zone is located in the transparent wall of the enclosure and extends around the inner perimeter of the ring so that a technician can insert his hands into the enclosure to reach any point within. The inventive enclosures provide more containment area per unit area of floor space than conventional material isolation enclosures. 3 figures

Fuel salt and container material studies for MOSART transforming system

Energy Technology Data Exchange (ETDEWEB)

Ignatiev, V.; Feynberg, O.; Merzlyakov, A.; Surenkov, A.; Zagnitko, A. [National Research Center, Kurchatov Institute, Moscow (Russian Federation); Afonichkin, V.; Bovet, A.; Khokhlov, V. [Institute of High Temperature Electrochemisty, Ekaterinburg (Russian Federation); Subbotin, V.; Gordeev, M.; Panov, A.; Toropov, A. [Institute of Technical Physics, Snezhinsk (Russian Federation)

2013-07-01

A study is under progress to examine the feasibility of single stream Molten Salt Actinide Recycling and Transmuting system without and with Th support (MOSART) fuelled with different compositions of actinide tri-fluorides (AnF{sub 3}) from used LWR fuel. New fast-spectrum design options with homogeneous core and fuel salts with high enough solubility for AnF{sub 3} are being examined because of new goals. The flexibility of single fluid MOSART concept with Th support is underlined, particularly, possibility of its operation in self-sustainable mode (Conversion Ratio: CR=1) using different loadings and make up. The paper summarizes the most current status of fuel salt and container material data for the MOSART concept received within ISTC-3749 and ROSATOM-MARS projects. Key physical and chemical properties of various fluoride fuel salts are reported. The issues like salt purification, the electroreduction of U(IV) to U(III) in LiF-ThF{sub 4} and the electroreduction of Yb(III) to Yb(II) in LiF-NaF are detailed.

Safety system for reactor container

International Nuclear Information System (INIS)

Shimizu, Miwako; Seki, Osamu; Mano, Takio.

1995-01-01

A slanted structure is formed below a reactor core where there is a possibility that molten reactor core materials are dropped, and above a water level of a pool which is formed by coolants flown from a reactor recycling system and accumulated on the inner bottom of the reactor container, to prevent molten fuels from dropping at once in the form of a large amount of lump. The molten materials are provisionally received on the structure, gradually formed into small pieces and then dropped. Further, the molten materials are dropped and received provisionally on a group of coolant-flowing pipelines below the structure, to lower the temperature of the molten materials, and then the reactor core molten materials are gradually formed into small pieces and dropped into the pool water. Since they are not dropped directly into the pool water but dropped gradually into the pool water as small droplets, occurrence of steam explosion can be reduced. The occurrence of steam explosion due to dropped molten reactor core material and pool water is suppressed, and the molten materials are kept in the pool water, thereby enabling to maintain the integrity of the reactor container more effectively. (N.H.)

Sulfur containing nanoporous materials, nanoparticles, methods and applications

Science.gov (United States)

Archer, Lynden A.; Navaneedhakrishnan, Jayaprakash

2018-01-30

Sulfur containing nanoparticles that may be used within cathode electrodes within lithium ion batteries include in a first instance porous carbon shape materials (i.e., either nanoparticle shapes or "bulk" shapes that are subsequently ground to nanoparticle shapes) that are infused with a sulfur material. A synthetic route to these carbon and sulfur containing nanoparticles may use a template nanoparticle to form a hollow carbon shape shell, and subsequent dissolution of the template nanoparticle prior to infusion of the hollow carbon shape shell with a sulfur material. Sulfur infusion into other porous carbon shapes that are not hollow is also contemplated. A second type of sulfur containing nanoparticle includes a metal oxide material core upon which is located a shell layer that includes a vulcanized polymultiene polymer material and ion conducting polymer material. The foregoing sulfur containing nanoparticle materials provide the electrodes and lithium ion batteries with enhanced performance.

A method of providing a barrier in a fracture-containing system

DEFF Research Database (Denmark)

2014-01-01

The present invention relates to a method of providing a barrier in a fracture-containing system, comprising: i) Providing a treatment fluid comprising: a) a base fluid; b) an elastomeric material, wherein said elastomeric material comprises at least one polymer capable of crosslinking into an el......The present invention relates to a method of providing a barrier in a fracture-containing system, comprising: i) Providing a treatment fluid comprising: a) a base fluid; b) an elastomeric material, wherein said elastomeric material comprises at least one polymer capable of crosslinking...... into an elastomer, and c) at least one crosslinking agent; ii) Placing the treatment fluid in a fracture-containing system; iii) Allowing the elastomeric material to crosslink with itself to form a barrier in said fracture-containing system; wherein the elastomeric material and/or the crosslinking agent...... are of neutral buoyancy with regard to the base fluid. The invention is contemplated to having utility not only in the oil-drilling industry but also in the plugging of fractures in sewer drains, pipelines etc....

FCA containment and surveillance (C/S) system

International Nuclear Information System (INIS)

Ogawa, Hironobu; Mukaiyama, Takehiko; Yokota, Yasuhiro.

1994-11-01

The Fast Critical Assembly (FCA) facility of the Japan Atomic Energy Research Inst. (JAERI) is internationally recognized as one of the most sensitive facility in the world from the viewpoint of international safeguards, because the facility possesses a large amount of metallic uranium and metallic plutonium, which are needed to perform various physical experiments. These material are subject to frequent verifications by the inspectorate, the International Atomic Energy Agency (IAEA) and the domestic authority (Science and Technology Agency of Japan, STA). Those verifications require inspectors to access to these materials for measurements and applications of seals. Human resources increase of irradiations and restrictions on the freedom of physical experiments, that are inevitably associated with these inspection activities, have been a serious problem that causes significant burdens for all relating parties. To decrease these burdens without any confliction with the inspection goals, an advanced comprehensive system of containment and surveillance has been developed. The FCA Containment and Surveillance (C/S) System consists of tow independent subsystems, i. e. Portal Monitor (P/M) and Penetration Monitor(PN/M). In this system the internal wall of the reactor building is used as a part of containment for the safeguards purpose, which enables the portal, that is installed at the internal wall of the reactor building, to be used as an area for monitoring of any removal of nuclear material. A metal detector of high sensitivity has been selected for the system since all nuclear materials possessed by the FCA has metallic forms. The internal wall has several penetrations for utility purposes, which should also be monitored for the purpose of detecting any removal of nuclear material from the reactor core area. A penetration monitor system has been developed for this purpose. This report describes functions of the system and their operation procedures. (author)

Container for shipping dangerous material

International Nuclear Information System (INIS)

Blum, P.T.

1987-01-01

This container for shipping dangerous material is made by a cylindrical casing of austenitic stainless steel with rounded ends and walls of uniform thickness with welded joins, a tubular metal shock absorber fixed over each end of the casing, removable lugs fixed to the casing, optionally retainers for the material within the casing [fr

Detecting nuclear materials smuggling: performance evaluation of container inspection policies.

Science.gov (United States)

Gaukler, Gary M; Li, Chenhua; Ding, Yu; Chirayath, Sunil S

2012-03-01

In recent years, the United States, along with many other countries, has significantly increased its detection and defense mechanisms against terrorist attacks. A potential attack with a nuclear weapon, using nuclear materials smuggled into the country, has been identified as a particularly grave threat. The system for detecting illicit nuclear materials that is currently in place at U.S. ports of entry relies heavily on passive radiation detectors and a risk-scoring approach using the automated targeting system (ATS). In this article we analyze this existing inspection system and demonstrate its performance for several smuggling scenarios. We provide evidence that the current inspection system is inherently incapable of reliably detecting sophisticated smuggling attempts that use small quantities of well-shielded nuclear material. To counter the weaknesses of the current ATS-based inspection system, we propose two new inspection systems: the hardness control system (HCS) and the hybrid inspection system (HYB). The HCS uses radiography information to classify incoming containers based on their cargo content into "hard" or "soft" containers, which then go through different inspection treatment. The HYB combines the radiography information with the intelligence information from the ATS. We compare and contrast the relative performance of these two new inspection systems with the existing ATS-based system. Our studies indicate that the HCS and HYB policies outperform the ATS-based policy for a wide range of realistic smuggling scenarios. We also examine the impact of changes in adversary behavior on the new inspection systems and find that they effectively preclude strategic gaming behavior of the adversary. © 2011 Society for Risk Analysis.

Sensor-based material tagging system

International Nuclear Information System (INIS)

Vercellotti, L.C.; Cox, R.W.; Ravas, R.J.; Schlotterer, J.C.

1991-01-01

Electronic identification tags are being developed for tracking material and personnel. In applying electronic identification tags to radioactive materials safeguards, it is important to measure attributes of the material to ensure that the tag remains with the material. The addition of a microcontroller with an on-board analog-to-digital converter to an electronic identification tag application-specific integrated-circuit has been demonstrated as means to provide the tag with sensor data. Each tag is assembled into a housing, which serves as a scale for measuring the weight of a paint-can-sized container and its contents. Temperature rise of the can above ambient is also measured, and a piezoelectric detector detects disturbances and immediately puts the tag into its alarm and beacon mode. Radiation measurement was also considered, but the background from nearby containers was found to be excessive. The sensor-based tagging system allows tracking of the material in cans as it is stored in vaults or is moved through the manufacturing process. The paper presents details of the sensor-based material tagging system and describes a demonstration system

Simulations and imaging algorithm development for a cosmic ray muon tomography system for the detection of special nuclear material in transport containers

International Nuclear Information System (INIS)

Jewett, C.; Anghel, V.N.P.; Armitage, J.; Boudjemline, K.; Botte, J.; Bryman, D.; Bueno, J.; Charles, E.; Cousins, T.; Didsbury, R.; Erhardt, L.; Erlandson, A.; Gallant, G.; Jason, A.; Jonkmans, G.; Liu, Z.; McCall, M.; Noel, S.; Oakham, F.G.; Ong, D.; Stocki, T.; Thompson, M.; Waller, D.

2011-01-01

The Cosmic Ray Inspection and Passive Tomography (CRIPT) collaboration is developing a cosmic ray muon tomography system to identify Special Nuclear Materials (SNM) in cargo containers. In order to gauge the viability of the technique, and to determine the best detector type, GEANT4 was used to simulate the passage of cosmic ray muons through a cargo container. The scattering density estimation (SDE) algorithm was developed and tested with data from these simulations to determine how well it could reconstruct the interior of a container. The simulation results revealed the ability of cosmic ray muon tomography techniques to image spheres of lead-shielded Special Nuclear Materials (SNM), such as uranium or plutonium, in a cargo container, containing a cargo of granite slabs. (author)

Simulations and imaging algorithm development for a cosmic ray muon tomography system for the detection of special nuclear material in transport containers

Energy Technology Data Exchange (ETDEWEB)

Jewett, C.; Anghel, V.N.P. [Atomic Energy of Canada Limited, Chalk River, Ontario (Canada); Armitage, J.; Boudjemline, K.; Botte, J. [Carleton Univ., Dept. of Physics, Ottawa, Ontario (Canada); Bryman, D. [Advanced Applied Physics Solutions, Vancouver, British Columbia (Canada); Univ. of British Columbia, Vancouver, British Columbia (Canada); Bueno, J. [Advanced Applied Physics Solutions, Vancouver, British Columbia (Canada); Charles, E. [Canada Border Services Agency, Ottawa, Ontario (Canada); Cousins, T. [International Safety Research, Ottawa, Ontario (Canada); Didsbury, R. [Atomic Energy of Canada Limited, Chalk River, Ontario (Canada); Erhardt, L. [Defence Research and Development Canada, Ottawa, Ontario (Canada); Erlandson, A. [Carleton Univ., Dept. of Physics, Ottawa, Ontario (Canada); Gallant, G. [Canada Border Services Agency, Ottawa, Ontario (Canada); Jason, A. [Los Alamos National Laboratory, Los Alamos (United States); Jonkmans, G. [Atomic Energy of Canada Limited, Chalk River, Ontario (Canada); Liu, Z. [Advanced Applied Physics Solutions, Vancouver, British Columbia (Canada); Univ. of British Columbia, Vancouver, British Columbia (Canada); McCall, M.; Noel, S. [International Safety Research, Ottawa, Ontario (Canada); Oakham, F.G. [Carleton Univ., Dept. of Physics, Ottawa, Ontario (Canada); TRIUMF, Vancouver, British Columbia, (Canada); Ong, D.; Stocki, T. [Health Canada, Ottawa, Ontario (Canada); Thompson, M. [Atomic Energy of Canada Limited, Chalk River, Ontario (Canada); Waller, D. [Defence Research and Development Canada, Ottawa, Ontario (Canada)

2011-07-01

The Cosmic Ray Inspection and Passive Tomography (CRIPT) collaboration is developing a cosmic ray muon tomography system to identify Special Nuclear Materials (SNM) in cargo containers. In order to gauge the viability of the technique, and to determine the best detector type, GEANT4 was used to simulate the passage of cosmic ray muons through a cargo container. The scattering density estimation (SDE) algorithm was developed and tested with data from these simulations to determine how well it could reconstruct the interior of a container. The simulation results revealed the ability of cosmic ray muon tomography techniques to image spheres of lead-shielded Special Nuclear Materials (SNM), such as uranium or plutonium, in a cargo container, containing a cargo of granite slabs. (author)

Fractionated-combustion analysis of carbonate-containing phases in composite materials of the hydroxyapatite-calcium carbonate system

Science.gov (United States)

Goldberg, M. A.; Shibaeva, T. V.; Smirnov, V. V.; Kutsev, S. V.; Barinov, S. M.; Grigorovich, K. V.

2012-12-01

Materials in the hydroxyapatite (HA)-calcium carbonate (CC) system were synthesized by a precipitation method from aqueous solutions. According to the data of X-ray phase analysis and IR spectroscopy, the powders consisted of CC and AB-type carbonate-substituted HA (CHA). In order to determine the content of carbonate-containing phases in materials, the temperature-temporal mode of fractionated-combustion analysis of carbon was developed. The quantitative phase ratios and the degree of substitution of carbonate groups in CHA were determined. It was shown that the degree of substitution of carbonate groups in CHA increased from 2.47 to 5.31 wt % as the CC content increased from 13.50 to 88.33 wt %.

Containment system of contamination in irradiated materials handling laboratories

International Nuclear Information System (INIS)

Lobao, A.S.T.; Araujo, J.A. de; Camilo, R.L.

1988-01-01

A study to prevent radiactivity release in lab scale is presented. As a basis for the design all the limits established by the IAEA for ventilation systems were observed. An evaluation of the different parameters involved in the design have been made, resulting in the specification of the working areas, ducts and filtering systems in order to get the best conditions for the safe handling of irradiated materials. (author) [pt

Complex-wide representation of material packaged in 3013 containers

Energy Technology Data Exchange (ETDEWEB)

Narlesky, Joshua E.; Peppers, Larry G.; Friday, Gary P.

2009-06-01

The DOE sites packaging plutonium oxide materials packaged according to Department of Energy 3013 Standard (DOE-STD-3013) are responsible for ensuring that the materials are represented by one or more samples in the Materials Identification and Surveillance (MIS) program. The sites categorized most of the materials into process groups, and the remaining materials were characterized, based on the prompt gamma analysis results. The sites issued documents to identify the relationships between the materials packaged in 3013 containers and representative materials in the MIS program. These “Represented” documents were then reviewed and concurred with by the MIS Working Group. However, these documents were developed uniquely at each site and were issued before completion of sample characterization, small-scale experiments, and prompt gamma analysis, which provided more detailed information about the chemical impurities and the behavior of the material in storage. Therefore, based on the most recent data, relationships between the materials packaged in 3013 containers and representative materials in the MIS program been revised. With the prompt gamma analysis completed for Hanford, Rocky Flats, and Savannah River Site 3013 containers, MIS items have been assigned to the 3013 containers for which representation is based on the prompt gamma analysis results. With the revised relationships and the prompt gamma analysis results, a Master “Represented” table has been compiled to document the linkages between each 3013 container packaged to date and its representative MIS items. This table provides an important link between the Integrated Surveillance Program database, which contains information about each 3013 container to the MIS items database, which contains the characterization, prompt gamma data, and storage behavior data from shelf-life experiments for the representative MIS items.

Complex-wide representation of material packaged in 3013 containers

International Nuclear Information System (INIS)

Narlesky, Joshua E.; Peppers, Larry G.; Friday, Gary P.

2009-01-01

The DOE sites packaging plutonium oxide materials packaged according to Department of Energy 3013 Standard (DOE-STD-3013) are responsible for ensuring that the materials are represented by one or more samples in the Materials Identification and Surveillance (MIS) program. The sites categorized most of the materials into process groups, and the remaining materials were characterized, based on the prompt gamma analysis results. The sites issued documents to identify the relationships between the materials packaged in 3013 containers and representative materials in the MIS program. These 'Represented' documents were then reviewed and concurred with by the MIS Working Group. However, these documents were developed uniquely at each site and were issued before completion of sample characterization, small-scale experiments, and prompt gamma analysis, which provided more detailed information about the chemical impurities and the behavior of the material in storage. Therefore, based on the most recent data, relationships between the materials packaged in 3013 containers and representative materials in the MIS program have been revised. With the prompt gamma analysis completed for Hanford, Rocky Flats, and Savannah River Site 3013 containers, MIS items have been assigned to the 3013 containers for which representation is based on the prompt gamma analysis results. With the revised relationships and the prompt gamma analysis results, a Master 'Represented' table has been compiled to document the linkages between each 3013 container packaged to date and its representative MIS items. This table provides an important link between the Integrated Surveillance Program database, which contains information about each 3013 container to the MIS items database, which contains the characterization, prompt gamma data, and storage behavior data from shelf-life experiments for the representative MIS items

System for inspection of stacked cargo containers

Science.gov (United States)

Derenzo, Stephen [Pinole, CA

2011-08-16

The present invention relates to a system for inspection of stacked cargo containers. One embodiment of the invention generally comprises a plurality of stacked cargo containers arranged in rows or tiers, each container having a top, a bottom a first side, a second side, a front end, and a back end; a plurality of spacers arranged in rows or tiers; one or more mobile inspection devices for inspecting the cargo containers, wherein the one or more inspection devices are removeably disposed within the spacers, the inspection means configured to move through the spacers to detect radiation within the containers. The invented system can also be configured to inspect the cargo containers for a variety of other potentially hazardous materials including but not limited to explosive and chemical threats.

Transport containers for radioactive material

International Nuclear Information System (INIS)

Doroszlai, P.; Ferroni, F.

1984-01-01

A cylindrical container for the transportation of radioactive reactor elements includes a top end, a bottom end and a pair of removable outwardly curved shock absorbers, each including a double-shelled construction having an internal shell with a convex intrados configuration and an external shell with a convex extrados configuration, the shock absorbers being filled with a low density energy-absorbing material and mounted at the top end and the bottom end of the container, respectively, and each of the shock absorbers having a toroidal configuration, and deformable tubes disposed within the shock absorbers and extending in the axial direction of the container

Corrosion-Resistant Container for Molten-Material Processing

Science.gov (United States)

Stern, Theodore G.; McNaul, Eric

2010-01-01

In a carbothermal process, gaseous methane is passed over molten regolith, which is heated past its melting point to a temperature in excess of 1,625 C. At this temperature, materials in contact with the molten regolith (or regolith simulant) corrode and lose their structural properties. As a result, fabricating a crucible to hold the molten material and providing a method of contact heating have been problematic. Alternative containment approaches use a large crucible and limit the heat zone of the material being processed, which is inefficient because of volume and mass constraints. Alternative heating approaches use non-contact heating, such as by laser or concentrated solar energy, which can be inefficient in transferring heat and thus require higher power heat sources to accomplish processing. The innovation is a combination of materials, with a substrate material having high structural strength and stiffness and high-temperature capability, and a coating material with a high corrosion resistance and high-temperature capability. The material developed is a molybdenum substrate with an iridium coating. Creating the containment crucible or heater jacket using this material combination requires only that the molybdenum, which is easily processed by conventional methods such as milling, electric discharge machining, or forming and brazing, be fabricated into an appropriate shape, and that the iridium coating be applied to any surfaces that may come in contact with the corrosive molten material. In one engineering application, the molybdenum was fashioned into a container for a heat pipe. Since only the end of the heat pipe is used to heat the regolith, the container has a narrowing end with a nipple in which the heat pipe is snugly fit, and the external area of this nipple, which contacts the regolith to transfer heat into it, is coated with iridium. At the time of this reporting, no single material has been found that can perform the functions of this combination

Development of a re-brazeable containment system for special nuclear material storage and transport

International Nuclear Information System (INIS)

Pierce, J.D.; Stephens, J.J.; Walker, C.A.; Hosking, F.M.; Curlee, R.M.

1995-01-01

This report describes a novel means of closing and sealing small type B radioactive material transport packages for surface or air transport as governed by 10CFR71 or NUREG-0360 has been developed at Sandia National Laboratories (SNL). This method is a controlled brazing process that may be used to attach and seal a closure lid to a containment vessel and then remove it at a later time. The process may be performed multiple times without the need for special preparations of the braze joint. A number of advantages for utilization of this technique have been determined. A brazed seal has integrity at high temperatures for better protection in accident or abnormal environments. A properly designed joint has essentially the same strength as the parent metal. A closure that is brazed, therefore, will no longer be the anticipated point of failure for a broad range of accident environments. This technique will allow the containment vessel design to be optimized with a lighter, more uniform wall thickness throughout. Finally, with a well defined process for sealing, mechanical inspection, leak testing, and then reopening at a later time, automation of the process is relatively straightforward and the overall system should be as easy to use as one that utilizes elastomeric seals for containment

Characterization of plutonium-containing materials and storage canisters

International Nuclear Information System (INIS)

Mason, R.E.

1997-01-01

Throughout the weapons complex, plutonium materials are stored in various containers. Some plutonium has been stored for 20 yr or more. The physical and chemical properties of the plutonium material and the containers that hold it are often not well characterized. The U.S. Department of Energy (DOE) 3013 standard sets criteria to which stored material must conform. The 3013 standard regulates materials that hold 50% or greater plutonium, and the other 50% is not specified and is usually unknown. The Materials Identification and Surveillance project is tasked to characterize representative materials and begin to characterize the other 50% and to show that materials can be brought into 3013 criteria conformance through thermal treatments

Transport of bundles and equipment which contain radioactive material

International Nuclear Information System (INIS)

1987-01-01

This norm settles down: 1) The requirements that should be completed in relation to safety precautions and protection against ionizing radiations during the transport radioactive material and/or equipment containing it, in order to avoid risks to the collective and the environment. 2) The basic information on procedures that will be completed in the event of happening accidents during the transport or the transit storage of radioactive material and/or equipment that contain it. 3) The measures of security and physical protection during the transport of radioactive material and/or equipment containing it. This norm is applied: 1) To all the ways of transport (by air, by ground and by ship, fluvial and marine) of radioactive material and/or equipment that contain it. 2) To all natural or legal, public or private person, devoted to install, produce, trade, market, import or export radioactive materials and/or equipment containing it, and that needs to transport them as main or secondary activity [es

Candidate container materials for Yucca Mountain waste package designs

International Nuclear Information System (INIS)

McCright, R.D.; Halsey, W.G.; Gdowski, G.E.; Clarke, W.L.

1991-09-01

Materials considered as candidates for fabricating nuclear waste containers are reviewed in the context of the Conceptual Design phase of a potential repository located at Yucca Mountain. A selection criteria has been written for evaluation of candidate materials for the next phase -- Advanced Conceptual Design. The selection criteria is based on the conceptual design of a thin-walled container fabricated from a single metal or alloy; the criteria consider the performance requirements on the container and the service environment in which the containers will be emplaced. A long list of candidate materials is evaluated against the criteria, and a short list of materials is proposed for advanced characterization in the next design phase

Risk ranking of LANL nuclear material storage containers for repackaging prioritization.

Science.gov (United States)

Smith, Paul H; Jordan, Hans; Hoffman, Jenifer A; Eller, P Gary; Balkey, Simon

2007-05-01

Safe handling and storage of nuclear material at U.S. Department of Energy facilities relies on the use of robust containers to prevent container breaches and subsequent worker contamination and uptake. The U.S. Department of Energy has no uniform requirements for packaging and storage of nuclear materials other than those declared excess and packaged to DOE-STD-3013-2000. This report describes a methodology for prioritizing a large inventory of nuclear material containers so that the highest risk containers are repackaged first. The methodology utilizes expert judgment to assign respirable fractions and reactivity factors to accountable levels of nuclear material at Los Alamos National Laboratory. A relative risk factor is assigned to each nuclear material container based on a calculated dose to a worker due to a failed container barrier and a calculated probability of container failure based on material reactivity and container age. This risk-based methodology is being applied at LANL to repackage the highest risk materials first and, thus, accelerate the reduction of risk to nuclear material handlers.

Kinetics and Efficiency of H2O2 Activation by Iron-Containing Minerals and Aquifer Materials

Science.gov (United States)

Pham, Anh Le-Tuan; Doyle, Fiona M.; Sedlak, David L.

2014-01-01

To gain insight into factors that control H2O2 persistence and ˙OH yield in H2O2-based in situ chemical oxidation systems, the decomposition of H2O2 and transformation of phenol were investigated in the presence of iron-containing minerals and aquifer materials. Under conditions expected during remediation of soil and groundwater, the stoichiometric efficiency, defined as the amount of phenol transformed per mole of H2O2 decomposed, varied from 0.005 to 0.28%. Among the iron-containing minerals, iron oxides were 2 to 10 times less efficient in transforming phenol than iron-containing clays and synthetic iron-containing catalysts. In both iron-containing mineral and aquifer materials systems, the stoichiometric efficiency was inversely correlated with the rate of H2O2 decomposition. In aquifer materials systems, the stoichiometric efficiency was also inversely correlated with the Mn content, consistent with the fact that the decomposition of H2O2 on manganese oxides does not produce ˙OH. Removal of iron and manganese oxide coatings from the surface of aquifer materials by extraction with citrate-bicarbonate-dithionite slowed the rate of H2O2 decomposition on aquifer materials and increased the stoichiometric efficiency. In addition, the presence of 2 mM of dissolved SiO2 slowed the rate of H2O2 decomposition on aquifer materials by over 80% without affecting the stoichiometric efficiency. PMID:23047055

Endurance test report of rubber sealing materials for the containment vessel

International Nuclear Information System (INIS)

Yamamoto, R.; Watanabe, K.; Hanashima, K.

2015-01-01

In the event of a nuclear power plant accident such as a core meltdown and a cooling system failure, the containment contains radioactive materials released from the reactor pressure vessel to reduce the activity of the radioactive materials and the effects of radiation in the vicinity of the plant. Since high sealing performance and high pressure resistance are required of the containment, a silicone or EPDM rubber gasket with high heat and radiation resistance is used for the sealing of the sealing boundary of the containment. In recent years, it has been shown that a large amount of steam is released into the containment in the case of a severe accident. Consequently, radiation resistance at high temperature as well as steam resistance is required of the rubber gasket placed at the sealing boundary. However, the steam resistance of silicone rubber is not necessarily as good as that of EPDM rubber. Therefore, it is necessary to evaluate the sealing characteristics of rubber gaskets in such a degrading environment in a severe accident. O. Kato et al. [1] conducted a study on the degradation status of rubber gaskets and their application limits at high temperature. However, few studies have evaluated rubber gaskets in high-temperature radiation and steam environments. In this study, we degraded silicone rubber and EPDM rubber used for the containment in the high-temperature radiation and steam environments expected to occur in a severe accident and evaluated the useful life of the rubber as a sealing material by estimating the change in its performance as a sealing material from the change in permanent compressive strain in the rubber. (author)

Storage and transport containers for radioactive medical materials

International Nuclear Information System (INIS)

Suthanthiran, K.

1989-01-01

This patent describes a storage and transport container for small-diameter ribbon-like lengths of material including radioactive substances for use in medical treatments, comprising: an exterior shell for radiation shielding metal having top and bottom members of radiation shielding metal integral therewith; radiation shielding metal extending downward from the top of the container and forming a central cavity, the central cavity being separate from the exterior shell material of the container and extending downwardly a distance less than the height of the container; a plurality of small diameter carrier tubes located within the interior of the container and having one end of each tube opening through one side of the container and the other end of such tube opening through the opposite lateral side of the container with the central portion of each tube passing under the central cavity; and a plug of radiation shielding metal removably located in the top the central cavity for shielding the radiation from radiation sources located within the container

Detecting special nuclear materials in suspect containers using high-energy gamma rays emitted by fission products

Science.gov (United States)

Norman, Eric B [Oakland, CA; Prussin, Stanley G [Kensington, CA

2009-01-27

A method and a system for detecting the presence of special nuclear materials in a suspect container. The system and its method include irradiating the suspect container with a beam of neutrons, so as to induce a thermal fission in a portion of the special nuclear materials, detecting the gamma rays that are emitted from the fission products formed by the thermal fission, to produce a detector signal, comparing the detector signal with a threshold value to form a comparison, and detecting the presence of the special nuclear materials using the comparison.

Assessment of materials for nuclear fuel immobilization containers

Energy Technology Data Exchange (ETDEWEB)

Nuttall, K; Urbanic, V F

1981-09-01

A wide range of engineering metals and alloys has been assessed for their suitability as container materials for irradiated nuclear fuel intended for permanent disposal in a deep, underground hard-rock vault. The expected range of service conditions in the disposal vault are discussed, as well as the material properties required for this application. An important requirement is that the container last at least 500 years without being breached. The assessment is treated in two parts. Part I concentrates on the physical and mechanical metallurgy, with special reference to strength, weldability, potential embrittlement mechanisms and some economic aspects. Part II discusses possible mechanisms of metallic corrosion for the various engineering alloys and the expected range of environmental conditions in the vault. Localized corrosion and delayed fracture processes are identified as being most likely to limit container lifetime. Hence an essential requirement is that such processes either be absent or proceed at an insignificant rate. Three groups of alloys are recommended for further consideration as possible container materials: AISI 300 series austenitic stainless steels, high nickel-base alloys and very dilute titanium-base alloys. Specific alloys from each group are indicated as having the optimum combination of required properties, including cost. For container designs where the outer container shell does not independently support the service loads, copper should also be considered. The final material selection will depend primarily on the enviromental conditions in the vault. 42 figures, 31 tables.

Asbestos-Containing Materials (ACM) and Demolition

Science.gov (United States)

There are specific federal regulatory requirements that require the identification of asbestos-containing materials (ACM) in many of the residential buildings that are being demolished or renovated by a municipality.

Dynamic material accountancy in an integrated safeguards system

International Nuclear Information System (INIS)

Murrell, J.S.

1979-01-01

The nuclear material safeguards system at the Portsmouth Gaseous Diffusion Plant is currently being improved. A new material control system will provide computerized monitoring and accountability, and a new physical protection system will provide upgraded perimeter and portal entry monitoring. The control system incorporates remote computer terminals at all processing, transfer and storage areas throughout the plant. Terminal equipment is interfaced to a computer through teletype equipment. A typical terminal transaction would require verification that the particular activity (material movement or process operation) is authorized, identifying the container involved, weighing the container, and then verifying the enrichment with non-destructive assay instrumentation. The system, when fully operational, will provide near real-time accountability for each eight-hour work shift for all items in process. (author)

Dynamic material accountancy in an integrated safeguards system

International Nuclear Information System (INIS)

Murrell, J.S.

1978-01-01

The nuclear material safeguards system at the Portsmouth Gaseous Diffusion Plant is currently being improved. A new material control system will provide computerized monitoring and accountability, and a new physical protection system will provide upgraded perimeter and portal entry monitoring. The control system incorporates remote computer terminals at all processing, transfer, and storage areas throughout the plant. Terminal equipment is interfaced to a computer through teletype equipment. A typical terminal transaction would require verification that the particular activity (material movement or process operation) is authorized, identifying the container involved, weighing the container, and then verifying the enrichment with non-destructive assay instrumentation. The system, when fully operational, will provide near real-time accountability for each eight-hour work shift for all items in process

Fluorine analysis of human enamel around fluoride-containing materials under different pH-cycling by {mu}-PIGE/PIXE system

Energy Technology Data Exchange (ETDEWEB)

Komatsu, H., E-mail: kom@den.hokudai.ac.jp [Graduate School of Dental Medicine, Hokkaido University, Kita-13, Nishi-7, Kita-ku, Sapporo 060-8586 (Japan); Yamamoto, H. [Graduate School of Dentistry, Osaka University, 1-8 Yamada-Oka, Suita 565-0871 (Japan); Matsuda, Y.; Kijimura, T.; Kinugawa, M.; Okuyama, K. [Graduate School of Dental Medicine, Hokkaido University, Kita-13, Nishi-7, Kita-ku, Sapporo 060-8586 (Japan); Nomachi, M. [Graduate School of Science, Osaka University, 1-1 Machikaneyama, Toyonaka 560-0043 (Japan); Yasuda, K. [Wakasa Wan Energy Research Center, 64-52-1 Hase, Tsuruga 914-0192 (Japan); Satoh, T. [Advanced Radiation Technology, TARRI, JAEA, 1233 Watanuki-Machi, Takasaki 370-1292 (Japan); Oikawa, S. [National Institute of Radiological Science, 4-9-1, Anagawa, Inage-ku, Chiba 263-8555 (Japan)

2011-10-15

The caries preventive effect of fluoride-containing materials (FCMs) might depend on the caries risk of the individuals. Two pairs of demineralizing and remineralizing solutions of pH-cycling were prepared for simulating low and high caries risk. The purpose of this study was to determine fluorine (F) uptake into human enamel around FCMs under different pH-cycling using the in-air {mu}-PIGE/PIXE system. Fluoride-containing glass ionomer cement (Fuji IX{sub GP} FAST CAPSULE (FN)), and composite resin (BEAUTIFIL II with FLUORO BOND SHAKE ONE (BS)) were used in this study. The pH-cycling (pH 6.8-4.5) was carried out for 5 weeks. After pH-cycling, the caries progression was analyzed using transverse micro-radiography (TMR). The fluorine and calcium distributions in the carious lesion in each specimen were evaluated using the PIGE/PIXE system. From TMR analysis, there was a difference in caries risk between the two kinds of pH-cycling. Although the caries preventive effect of BS and FN was confirmed at low risk, the effect at high risk was confirmed for FN only. From the analysis of the fluorine uptake in the outer 200 {mu}m of the lesion we concluded that there was no significant difference between the pH-cycling solutions. However, we found different fluorine concentrations in the enamel for the two FCMs. The decreased caries progression under high risk for FN indicated that an adequate amount of fluorine supplied from the material is required at higher caries risk. It was confirmed that the caries preventive effect of FCM depends on the caries risk. The fluorine analysis of teeth under various pH-cycling conditions gives information to evaluate the caries preventive effect of fluoride-containing materials according to the caries risk.

Fluorine analysis of human enamel around fluoride-containing materials under different pH-cycling by μ-PIGE/PIXE system

International Nuclear Information System (INIS)

Komatsu, H.; Yamamoto, H.; Matsuda, Y.; Kijimura, T.; Kinugawa, M.; Okuyama, K.; Nomachi, M.; Yasuda, K.; Satoh, T.; Oikawa, S.

2011-01-01

The caries preventive effect of fluoride-containing materials (FCMs) might depend on the caries risk of the individuals. Two pairs of demineralizing and remineralizing solutions of pH-cycling were prepared for simulating low and high caries risk. The purpose of this study was to determine fluorine (F) uptake into human enamel around FCMs under different pH-cycling using the in-air μ-PIGE/PIXE system. Fluoride-containing glass ionomer cement (Fuji IX GP FAST CAPSULE (FN)), and composite resin (BEAUTIFIL II with FLUORO BOND SHAKE ONE (BS)) were used in this study. The pH-cycling (pH 6.8-4.5) was carried out for 5 weeks. After pH-cycling, the caries progression was analyzed using transverse micro-radiography (TMR). The fluorine and calcium distributions in the carious lesion in each specimen were evaluated using the PIGE/PIXE system. From TMR analysis, there was a difference in caries risk between the two kinds of pH-cycling. Although the caries preventive effect of BS and FN was confirmed at low risk, the effect at high risk was confirmed for FN only. From the analysis of the fluorine uptake in the outer 200 μm of the lesion we concluded that there was no significant difference between the pH-cycling solutions. However, we found different fluorine concentrations in the enamel for the two FCMs. The decreased caries progression under high risk for FN indicated that an adequate amount of fluorine supplied from the material is required at higher caries risk. It was confirmed that the caries preventive effect of FCM depends on the caries risk. The fluorine analysis of teeth under various pH-cycling conditions gives information to evaluate the caries preventive effect of fluoride-containing materials according to the caries risk.

Explicit Finite Element Modeling of Multilayer Composite Fabric for Gas Turbine Engine Containment Systems, Phase II. Part 3; Material Model Development and Simulation of Experiments

Science.gov (United States)

Simmons, J.; Erlich, D.; Shockey, D.

2009-01-01

A team consisting of Arizona State University, Honeywell Engines, Systems & Services, the National Aeronautics and Space Administration Glenn Research Center, and SRI International collaborated to develop computational models and verification testing for designing and evaluating turbine engine fan blade fabric containment structures. This research was conducted under the Federal Aviation Administration Airworthiness Assurance Center of Excellence and was sponsored by the Aircraft Catastrophic Failure Prevention Program. The research was directed toward improving the modeling of a turbine engine fabric containment structure for an engine blade-out containment demonstration test required for certification of aircraft engines. The research conducted in Phase II began a new level of capability to design and develop fan blade containment systems for turbine engines. Significant progress was made in three areas: (1) further development of the ballistic fabric model to increase confidence and robustness in the material models for the Kevlar(TradeName) and Zylon(TradeName) material models developed in Phase I, (2) the capability was improved for finite element modeling of multiple layers of fabric using multiple layers of shell elements, and (3) large-scale simulations were performed. This report concentrates on the material model development and simulations of the impact tests.

Mineralogical conversion of asbestos containing materials

International Nuclear Information System (INIS)

Pulsford, S.K.; Foltz, A.D.; Ek, R.B.

1996-01-01

The principal objective of the Technical Task Plan (TTP) is to demonstrate a thermal-chemical mineralogical asbestos conversion unit at the Hanford Site, which converts non-radiological asbestos containing materials (ACMs) into an asbestos-free material. The permanent thermal-chemical mineralogical conversion of ACMs to a non-toxic, non-hazardous, potentially marketable end product should not only significantly reduce the waste stream volumes but terminate the open-quotes cradle to graveclose quotes ownership liabilities

Design compliance matrix waste sample container filling system for nested, fixed-depth sampling system

International Nuclear Information System (INIS)

BOGER, R.M.

1999-01-01

This design compliance matrix document provides specific design related functional characteristics, constraints, and requirements for the container filling system that is part of the nested, fixed-depth sampling system. This document addresses performance, external interfaces, ALARA, Authorization Basis, environmental and design code requirements for the container filling system. The container filling system will interface with the waste stream from the fluidic pumping channels of the nested, fixed-depth sampling system and will fill containers with waste that meet the Resource Conservation and Recovery Act (RCRA) criteria for waste that contains volatile and semi-volatile organic materials. The specifications for the nested, fixed-depth sampling system are described in a Level 2 Specification document (HNF-3483, Rev. 1). The basis for this design compliance matrix document is the Tank Waste Remediation System (TWRS) desk instructions for design Compliance matrix documents (PI-CP-008-00, Rev. 0)

Arsenic removal using steel manufacturing byproducts as permeable reactive materials in mine tailing containment systems.

Science.gov (United States)

Ahn, Joo Sung; Chon, Chul-Min; Moon, Hi-Soo; Kim, Kyoung-Woong

2003-05-01

Steel manufacturing byproducts were tested as a means of treating mine tailing leachate with a high As concentration. Byproduct materials can be placed in situ as permeable reactive barriers to control the subsurface release of leachate from tailing containment systems. The tested materials had various compositions of elemental Fe, Fe oxides, Ca-Fe oxides and Ca hydroxides typical of different steel manufacturing processes. Among these materials, evaporation cooler dust (ECD), oxygen gas sludge (OGS), basic oxygen furnace slag (BOFS) and to a lesser degree, electrostatic precipitator dust (EPD) effectively removed both As(V) and As(III) during batch experiments. ECD, OGS and BOFS reduced As concentrations to <0.5mg/l from 25mg/l As(V) or As(III) solution in 72 h, exhibiting higher removal capacities than zero-valent iron. High Ca concentrations and alkaline conditions (pH ca. 12) provided by the dissolution of Ca hydroxides may promote the formation of stable, sparingly soluble Ca-As compounds. When initial pH conditions were adjusted to 4, As reduction was enhanced, probably by adsorption onto iron oxides. The elution rate of retained As from OGS and ECD decreased with treatment time, and increasing the residence time in a permeable barrier strategy would be beneficial for the immobilization of As. When applied to real tailing leachate, ECD was found to be the most efficient barrier material to increase pH and to remove As and dissolved metals.

Radioactive material dry-storage facility and radioactive material containing method

International Nuclear Information System (INIS)

Kanai, Hidetoshi; Kumagaya, Naomi; Ganda, Takao.

1997-01-01

The present invention provides a radioactive material dry storage facility which can unify the cooling efficiency of a containing tube and lower the pressure loss in a storage chamber. Namely, a cylindrical body surrounds a first containing tube situated on the side of an air discharge portion among a plurality of containing tubes and forms an annular channel extending axially between the cylindrical body and the first containing tube. An air flow channel partitioning member is disposed below a second containing tube situated closer to an air charging portion than the first containing tube. A first air flow channel is formed below the air channel partitioning member extending from the air charging portion to the annular channel. The second air channel is formed above the air channel partitioning member and extends from the air charging portion to the air discharge portion by way of a portion between the second containing tubes and the portion between the cylindrical body and the first containing tube. Then, low temperature air can be led from the air charging portion to the periphery of the first containing tube. The effect of cooling the first containing tube can be enhanced. The difference between the cooling efficiency between the second containing tube and the first containing tube is decreased. (I.S.)

Treating agent for urea containing radioactive materials

International Nuclear Information System (INIS)

Ogawa, Hiroshi; Maki, Kentaro.

1973-01-01

Object: To add a coagulant into urea containing radioactive material to precipitate and remove the radioactive material in the urea. Structure: Iodosalt is added into urea and next, a mixed reagent in which silver ion or silver acetic ion and iron hydroxide precipitation or ferrite ion coexist is added therein. The urea is treated to have a sufficient alkaline, after which it is introduced into a basket type centrifuge formed with a filter layer in combination of an upper glass fiber layer and a lower active carbon layer. The treating agent can uniformly remove radioactive ion and radioactive chelate within urea containing inorganic salt and various metabolites. (Nakamura, S.)

Nondestructive Examination Of Plutonium-Bearing Material Containers

International Nuclear Information System (INIS)

Yerger, L.; Mcclard, J.; Traver, L.; Grim, T.

2010-01-01

The first nondestructive examination (NDE) of 3013-type containers as part of the Department of Energy's (DOE's) Integrated Surveillance Program (ISP) was performed in February, 2005. Since that date 280 NDE surveillances on 255 containers have been conducted. These containers were packaged with plutonium-bearing materials at multiple DOE sites. The NDE surveillances were conducted at Hanford, Lawrence Livermore National Laboratory (LLNL), and Savannah River Site (SRS). These NDEs consisted of visual inspection, mass verification, radiological surveys, prompt gamma analysis, and radiography. The primary purpose of performing NDE surveillances is to determine if there has been a significant pressure buildup inside the inner 3013 container. This is done by measuring the lid deflection of the inner 3013 container using radiography images. These lid deflection measurements are converted to pressure measurements to determine if a container has a pressure of a 100 psig or greater. Making this determination is required by Surveillance and Monitoring Plan (S and MP). All 3013 containers are designed to withstand at least 699 psig as specified by DOE-STD-3013. To date, all containers evaluated have pressures under 50 psig. In addition, the radiography is useful in evaluating the contents of the 3013 container as well as determining the condition of the walls of the inner 3013 container and the convenience containers. The radiography has shown no signs of degradation of any container, but has revealed two packaging anomalies. Quantitative pressure measurements based on lid deflections, which give more information than the 'less than or greater than 100 psig' (pass/fail) data are also available for many containers. Statistical analyses of the pass/fail data combined with analysis of the quantitative data show that it is extremely unlikely that any container in the population of 3013 containers considered in this study (e.g., containers packaged according to the DOE-STD-3013

Steam reforming as an alternative technique for treatment of oil sludge containing naturally occurring radioactive material

International Nuclear Information System (INIS)

Norasalwa Zakaria; Muhd Noor Muhd Yunus; Mohd Khairi Muhd Said; Mohamad Azman Che Mat Isa; Mohd Puad Abu

2004-01-01

Steam reforming treatment system is an innovative technology that holds a potential to treat mixed waste containing radioactive material. The system is utilizing the thermal heat of the superheated steam at 500 degree C to produce combustible gases and integrates it with ash melting at 1400 degree C for final destruction. In this system, liquids are evaporated, organics are converted into a hydrogen-rich gas, chlorinated compounds are converted in hydrochloric acid, and reactive chemicals in the waste containing radionuclide and heavy metals are converted into the stable product through ash melting dioxins and furans are not formed, but instead are destroyed in the reducing environment of the system. No secondary pollutants are produced from the system that requires subsequent treatment. The system is divided into three development stages, and currently the project is progressing at development stage 1. This project is an entailment of a concentrated effort to solve oil sludge containing radioactive material treatment issue. (Author)

Reuse of Material Containing Natural Radionuclides - 12444

Energy Technology Data Exchange (ETDEWEB)

Metlyaev, E.G.; Novikova, N.J. [Burnasyan Federal Medical Biophysical Centre, Moscow (Russian Federation)

2012-07-01

Disposal of and use of wastes containing natural radioactive material (NORM) or technologically enhanced natural radioactive material (TENORM) with excessive natural background as a building material is very important in the supervision body activity. At the present time, the residents of Octyabrsky village are under resettlement. This village is located just near the Priargunsky mining and chemical combine (Ltd. 'PPGHO'), one of the oldest uranium mines in our country. The vacated wooden houses in the village are demolished and partly used as a building material. To address the issue of potential radiation hazard of the wooden beams originating from demolition of houses in Octyabrsky village, the contents of the natural radionuclides (K-40, Th-232, Ra-226, U- 238) are being determined in samples of the wooden beams of houses. The NORM contents in the wooden house samples are higher, on average, than their content in the reference sample of the fresh wood shavings, but the range of values is rather large. According to the classification of waste containing the natural radionuclides, its evaluation is based on the effective specific activity. At the effective specific activity lower 1.5 kBq/kg and gamma dose rate lower 70 μR/h, the material is not considered as waste and can be used in building by 1 - 3 classes depending upon A{sub eff} value. At 1.5 kBq/kg < A{sub eff} ≤ 4 kBq/kg (4 class), the wooden beams might be used for the purpose of the industrial building, if sum of ratios between the radionuclide specific activity and its specific activity of minimum significance is lower than unit. The material classified as the waste containing the natural radionuclides has A{sub eff} higher 1.5 kBq /kg, and its usage for the purpose of house-building and road construction is forbidden. As for the ash classification and its future usage, such usage is unreasonable, because, according to the provided material, more than 50% of ash samples are considered as

Defense High Level Waste Disposal Container System Description Document

International Nuclear Information System (INIS)

2000-01-01

The Defense High Level Waste Disposal Container System supports the confinement and isolation of waste within the Engineered Barrier System of the Monitored Geologic Repository (MGR). Disposal containers are loaded and sealed in the surface waste handling facilities, transferred to the underground through the accesses using a rail mounted transporter, and emplaced in emplacement drifts. The defense high level waste (HLW) disposal container provides long-term confinement of the commercial HLW and defense HLW (including immobilized plutonium waste forms (IPWF)) placed within disposable canisters, and withstands the loading, transfer, emplacement, and retrieval loads and environments. U.S. Department of Energy (DOE)-owned spent nuclear fuel (SNF) in disposable canisters may also be placed in a defense HLW disposal container along with commercial HLW waste forms, which is known as 'co-disposal'. The Defense High Level Waste Disposal Container System provides containment of waste for a designated period of time, and limits radionuclide release. The disposal container/waste package maintains the waste in a designated configuration, withstands maximum handling and rockfall loads, limits the individual canister temperatures after emplacement, resists corrosion in the expected handling and repository environments, and provides containment of waste in the event of an accident. Defense HLW disposal containers for HLW disposal will hold up to five HLW canisters. Defense HLW disposal containers for co-disposal will hold up to five HLW canisters arranged in a ring and one DOE SNF canister in the ring. Defense HLW disposal containers also will hold two Multi-Canister Overpacks (MCOs) and two HLW canisters in one disposal container. The disposal container will include outer and inner cylinders, outer and inner cylinder lids, and may include a canister guide. An exterior label will provide a means by which to identify the disposal container and its contents. Different materials

Program to develop analytical tools for environmental and safety assessment of nuclear material shipping container systems

International Nuclear Information System (INIS)

Butler, T.A.

1978-11-01

This paper describes a program for developing analytical techniques to evaluate the response of nuclear material shipping containers to severe accidents. Both lumped-mass and finite element techniques are employed to predict shipping container and shipping container-carrier response to impact. The general impact problem is computationally expensive because of its nonlinear, three-dimensional nature. This expense is minimized by using approximate models to parametrically identify critical cases before more exact analyses are performed. The computer codes developed for solving the problem are being experimentally substantiated with test data from full-scale and scale-model container drop tests. 6 figures, 1 table

Storage vessel for containing radiation contaminated material

International Nuclear Information System (INIS)

Ogawa, Kazuya.

1995-01-01

A container pipe and an outer pipe are coaxially assembled integrally in a state where securing spacers are disposed between the container pipe and the outer pipe, and an annular flow channel is formed around the container pipe. Radiation contaminated material-containing body (glass solidified package) is contained in the container pipe. The container pipe and the outer pipe in an integrated state are suspended from a ceiling plug of a cell chamber of a storage vessel, and supporting devices are assembled between the pipes and a support structure. A shear/lug mechanism is used for the supporting devices. The combination of the shear/lug allows radial and vertical movement but restrict horizontal movement of the outer tube. The supporting devices are assembled while visually recognizing the state of the shear/lug mechanism between the outer pipe and the support mechanism. Accordingly, operationability upon assembling the container pipe and the outer pipe is improved. (I.N.)

Passive containment system

International Nuclear Information System (INIS)

Kleimola, F.W.

1977-01-01

Disclosed is a containment system that provides complete protection entirely by passive means for the loss of coolant accident in a nuclear power plant and wherein all stored energy released in the coolant blowdown is contained and absorbed while the nuclear fuel is prevented from over-heating by a high containment back-pressure and a reactor vessel refill system. The primary containment vessel is restored to a high sub-atmospheric pressure within a few minutes after accident initiation and the decay heat is safely transferred to the environment while radiolytic hydrogen is contained by passive means. 20 claims, 14 figures

Self-closing shielded container for use with radioactive materials

Science.gov (United States)

Smith, J.E.

A container for storage of radioactive material comprises a container body and a closure member. The closure member is coupled to the container body to enable the closure body to move automatically from a first position (e.g., closed) to a second position (open).

Guidelines for Assessment and Abatement of Asbestos-Containing Materials in Buildings.

Science.gov (United States)

Pielert, James H.; Mathey, Robert G.

This report presents guidelines, based on available information, for the assessment and abatement of asbestos-containing materials in buildings. Section 1 provides background information on the history and use of asbestos-containing products in buildings, the characteristics of asbestos fibers, products and materials containing asbestos, and…

An assessment of materials for nuclear fuel immobilization containers

International Nuclear Information System (INIS)

Nuttall, K.; Urbanic, V.F.

1981-09-01

A wide range of engineering metals and alloys was assessed for their suitability as container materials for irradiated nuclear fuel intended for permanent disposal in a deep, underground hard-rock vault. The container must last at least 500 years without being breached. Materials were assessed for their physical and mechanical metallurgy, weldability, potential embrittlement mechanisms, and economics. A study of the possible mechanisms of metallic corrosion for the various engineering alloys and the expected range of environmental conditons in the vault showed that localized corrosion and delayed fracture processes are the most likely to limit container lifetime. Thus such processes either must be absent or proceed at an insignificant rate. Three groups of alloys are recommended for further study: AISI 300 series austenitic stainless steels, high nickel-base alloys and very dilute titanium-base alloys. Specific alloys from each group are indicated as having the optimum combination of required properties, including cost. For container designs where the outer container shell does not independently support the service loads, copper should also be considered. The final material selection will depend primarily on the environmental conditions in the vault

LCA comparison of container systems in municipal solid waste management

International Nuclear Information System (INIS)

Rives, Jesus; Rieradevall, Joan; Gabarrell, Xavier

2010-01-01

The planning and design of integrated municipal solid waste management (MSWM) systems requires accurate environmental impact evaluation of the systems and their components. This research assessed, quantified and compared the environmental impact of the first stage of the most used MSW container systems. The comparison was based on factors such as the volume of the containers, from small bins of 60-80 l to containers of 2400 l, and on the manufactured materials, steel and high-density polyethylene (HDPE). Also, some parameters such as frequency of collections, waste generation, filling percentage and waste container contents, were established to obtain comparable systems. The methodological framework of the analysis was the life cycle assessment (LCA), and the impact assessment method was based on CML 2 baseline 2000. Results indicated that, for the same volume, the collection systems that use HDPE waste containers had more of an impact than those using steel waste containers, in terms of abiotic depletion, global warming, ozone layer depletion, acidification, eutrophication, photochemical oxidation, human toxicity and terrestrial ecotoxicity. Besides, the collection systems using small HDPE bins (60 l or 80 l) had most impact while systems using big steel containers (2400 l) had less impact. Subsequent sensitivity analysis about the parameters established demonstrated that they could change the ultimate environmental impact of each waste container collection system, but that the comparative relationship between systems was similar.

Hierarchy concepts: classification and preparation strategies for zeolite containing materials with hierarchical porosity.

Science.gov (United States)

Schwieger, Wilhelm; Machoke, Albert Gonche; Weissenberger, Tobias; Inayat, Amer; Selvam, Thangaraj; Klumpp, Michael; Inayat, Alexandra

2016-06-13

'Hierarchy' is a property which can be attributed to a manifold of different immaterial systems, such as ideas, items and organisations or material ones like biological systems within living organisms or artificial, man-made constructions. The property 'hierarchy' is mainly characterised by a certain ordering of individual elements relative to each other, often in combination with a certain degree of branching. Especially mass-flow related systems in the natural environment feature special hierarchically branched patterns. This review is a survey into the world of hierarchical systems with special focus on hierarchically porous zeolite materials. A classification of hierarchical porosity is proposed based on the flow distribution pattern within the respective pore systems. In addition, this review might serve as a toolbox providing several synthetic and post-synthetic strategies to prepare zeolitic or zeolite containing material with tailored hierarchical porosity. Very often, such strategies with their underlying principles were developed for improving the performance of the final materials in different technical applications like adsorptive or catalytic processes. In the present review, besides on the hierarchically porous all-zeolite material, special focus is laid on the preparation of zeolitic composite materials with hierarchical porosity capable to face the demands of industrial application.

Materials And Processes Technical Information System (MAPTIS) LDEF materials data base

Science.gov (United States)

Funk, Joan G.; Strickland, John W.; Davis, John M.

1993-01-01

A preliminary Long Duration Exposure Facility (LDEF) Materials Data Base was developed by the LDEF Materials Special Investigation Group (MSIG). The LDEF Materials Data Base is envisioned to eventually contain the wide variety and vast quantity of materials data generated from LDEF. The data is searchable by optical, thermal, and mechanical properties, exposure parameters (such as atomic oxygen flux) and author(s) or principal investigator(s). Tne LDEF Materials Data Base was incorporated into the Materials and Processes Technical Information System (MAPTIS). MAPTIS is a collection of materials data which has been computerized and is available to engineers, designers, and researchers in the aerospace community involved in the design and development of spacecraft and related hardware. The LDEF Materials Data Base is described and step-by-step example searches using the data base are included. Information on how to become an authorized user of the system is included.

Surveillance of sealed containers with plutonium oxide materials (ms163)

Science.gov (United States)

Worl, Laura; Berg, John; Ford, Doris; Martinez, Max; McFarlan, Jim; Morris, John; Padilla, Dennis; Rau, Karen; Smith, Coleman; Veirs, Kirk; Hill, Dallas; Prenger, Coyne

2000-07-01

DOE is embarking upon a program to store large quantities of plutonium-bearing materials for up to fifty years. Materials destined for long-term storage include metals and oxides that are stabilized and packaged according to the DOE storage standard, where the packaging consists of two nested, welded, stainless steel containers. We have designed instrumented storage containers that mimic the inner storage can specified in the 3013 standard at both full- and small-scale capacities (2.4 liter and 0.005 liter, respectively), Figures 1 and 2. The containers are designed to maintain the volume to material mass ratio while allowing the gas composition and pressure to be monitored over time.

SULPHUR DIOXIDE LEACHING OF URANIUM CONTAINING MATERIAL

Science.gov (United States)

Thunaes, A.; Rabbits, F.T.; Hester, K.D.; Smith, H.W.

1958-12-01

A process is described for extracting uranlum from uranium containing material, such as a low grade pitchblende ore, or mill taillngs, where at least part of the uraniunn is in the +4 oxidation state. After comminuting and magnetically removing any entrained lron particles the general material is made up as an aqueous slurry containing added ferric and manganese salts and treated with sulfur dioxide and aeration to an extent sufficient to form a proportion of oxysulfur acids to give a pH of about 1 to 2 but insufficient to cause excessive removal of the sulfur dioxide gas. After separating from the solids, the leach solution is adjusted to a pH of about 1.25, then treated with metallic iron in the presence of a precipitant such as a soluble phosphate, arsonate, or fluoride.

Contained scanning electron microscope facility for examining radioactive materials

International Nuclear Information System (INIS)

Hsu, C.W.

1986-03-01

At the Savannah River Laboratory (SRL) radioactive solids are characterized with a scanning electron microscope (SEM) contained in a glove box. The system includes a research-grade Cambridge S-250 SEM, a Tracor Northern TN-5500 x-ray and image analyzer, and a Microspec wavelength-dispersive x-ray analyzer. The containment facility has a glove box train for mounting and coating samples, and for housing the SEM column, x-ray detectors, and vacuum pumps. The control consoles of the instruments are located outside the glove boxes. This facility has been actively used since October 1983 for high alpha-activity materials such as plutonium metal and plutonium oxide powders. Radioactive defense waste glasses and contaminated equipment have also been examined. During this period the facility had no safety-related incidents, and personnel radiation exposures were maintained at less than 100 mrems

49 CFR 176.76 - Transport vehicles, freight containers, and portable tanks containing hazardous materials.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Transport vehicles, freight containers, and... TRANSPORTATION HAZARDOUS MATERIALS REGULATIONS CARRIAGE BY VESSEL General Handling and Stowage § 176.76 Transport... paragraphs (b) through (f) of this section, hazardous materials authorized to be transported by vessel may be...

Analysis of wallboard containing a phase change material

Science.gov (United States)

Tomlinson, J. J.; Heberle, D. P.

Phase change materials (PCMs) used on the interior of buildings hold the promise for improved thermal performance by reducing the energy requirements for space conditioning and by improving thermal comfort by reducing temperature swings inside the building. Efforts are underway to develop a gypsum wallboard containing a hydrocarbon PCM. With a phase change temperature in the room temperature range, the PCM wallboard adds substantially to the thermal mass of the building while serving the same architectural function as conventional wallboard. To determine the thermal and economic performance of this PCM wallboard, the Transient Systems Simulation Program (TRNSYS) was modified to accommodate walls that are covered with PCM plasterboard, and to apportion the direct beam solar radiation to interior surfaces of a building. The modified code was used to simulate the performance of conventional and direct-gain passive solar residential-sized buildings with and without PCM wallboard. Space heating energy savings were determined as a function of PCM wallboard characteristics. Thermal comfort improvements in buildings containing the PCM were qualified in terms of energy savings. The report concludes with a present worth economic analysis of these energy savings and arrives at system costs and economic payback based on current costs of PCMs under study for the wallboard application.

Wireless sensing system for non-invasive monitoring of attributes of contents in a container

Science.gov (United States)

Woodard, Stanley E. (Inventor)

2010-01-01

A wireless sensing system monitors the level, temperature, magnetic permeability and electrical dielectric constant of a non-gaseous material in a container. An open-circuit electrical conductor is shaped to form a two-dimensional geometric pattern that can store and transfer electrical and magnetic energy. The conductor resonates in the presence of a time-varying magnetic field to generate a harmonic response. The conductor is mounted in an environmentally-sealed housing. A magnetic field response recorder wirelessly transmits the time-varying magnetic field to power the conductor, and wirelessly detects the harmonic response that is an indication of at least one of level of the material in the container, temperature of the material in the container, magnetic permeability of the material in the container, and dielectric constant of the material in the container.

Tension in the tie-down chains of a shipping container for hazardous material

International Nuclear Information System (INIS)

Lo, T.Y.

1995-01-01

Chains are frequently used to tie the shipping containers of hazardous material to a truck bed. The tie-down system is nonlinear when the container is subjected to a triaxial force during transit. It is nonlinear because chains cannot carry compressive force, and the base of the container may partially lift off from the truck bed. A method was developed to calculate the amount of tension in the chains. This methodology includes three assumptions: (1) No friction exists between the container and the truck bed; (2) The container and the truck bed are rigid; and (3) All chains are properly tightened (i.e., no slacks) during preparation for shipment. The methodology employs an iterative process of a linear tie-down system. This linear system is derived from the nonlinear system with two additional assumptions: (a) All chains can carry compression as well as tension; and (b) There is a point contact between the container and the truck bed. This linear system has a closed-form solution. After the first solution of the linear system is obtained, the unreasonable, or physically impossible, rotational degree of freedom of the container and the chains with compressive force are eliminated in the follow-up iterative calculations using the same linear system. Unreasonable rotation is detected when the results indicate a rotation of the container into the truck bed. Zero rotational value is assigned to this degree of freedom in the follow-up iterations. For chains under compression, the chain length is replaced with a fictitiously large value because a long chain carries essentially no load. This process usually needs only two or three iterations and can easily be carried out in a spread sheet using such programs as Microsoft Excel or LOTUS 123

Heat storage system utilizing phase change materials government rights

Science.gov (United States)

Salyer, Ival O.

2000-09-12

A thermal energy transport and storage system is provided which includes an evaporator containing a mixture of a first phase change material and a silica powder, and a condenser containing a second phase change material. The silica powder/PCM mixture absorbs heat energy from a source such as a solar collector such that the phase change material forms a vapor which is transported from the evaporator to the condenser, where the second phase change material melts and stores the heat energy, then releases the energy to an environmental space via a heat exchanger. The vapor is condensed to a liquid which is transported back to the evaporator. The system allows the repeated transfer of thermal energy using the heat of vaporization and condensation of the phase change material.

Gamma motes for detection of radioactive materials in shipping containers

International Nuclear Information System (INIS)

Harold McHugh; William Quam; Stephan Weeks; Brendan Sever

2007-01-01

Shipping containers can be effectively monitored for radiological materials using gamma (and neutron) motes in distributed mesh networks. The mote platform is ideal for collecting data for integration into operational management systems required for efficiently and transparently monitoring international trade. Significant reductions in size and power requirements have been achieved for room-temperature cadmium zinc telluride (CZT) gamma detectors. Miniaturization of radio modules and microcontroller units are paving the way for low-power, deeply-embedded, wireless sensor distributed mesh networks

NucleDyne's passive containment system

International Nuclear Information System (INIS)

Falls, O.B. Jr.; Kleimola, F.W.

1987-01-01

A simple definition of the passive containment system is that it is a total safeguards system for light water reactors designed to prevent and contain any accidental release of radioactivity. Its passive features utilize the natural laws of physics and thermodynamics. The system encompasses three basic containments constructed as one integrated structure on the reactor building foundation. The primary containment encloses the reactor pressure vessel and coolant system and passive engineered safety systems and components. Auxiliary containment enclosures house auxiliary systems and components. Secondary containment (the reactor building), housing the primary and auxiliary containment structures, provides a second containment barrier as added defense-in-depth against leakage of radioactivity for all accidents assumed by the industry. The generic features of the passive containment system are applicable to both the boiling water reactors and the pressurized water reactors as standardized features for all power ranges. These features provide for a zero source term, the industry's ultimate safety goal. This paper relates to a four-loop pressurized water reactor

Development and implementation of automated radioactive materials handling systems

International Nuclear Information System (INIS)

Jacoboski, D.L.

1992-12-01

Material handling of radioactive and hazardous materials has forced the need to pursue remotely operated and robotic systems in light of operational safety concerns. Manual maneuvering, repackaging, overpacking and inspecting of containers which store radioactive and hazardous materials is the present mode of operation at the Department of Energy (DOE) Fernald Environmental Management Project (FEMP) in Fernald Ohio. The manual methods are unacceptable in the eyes of concerned site workers and influential community oversight committees. As an example to respond to the FEMP material handling needs, design efforts have been initiated to provide a remotely operated system to repackage thousands of degradated drums containing radioactive Thorium: Later, the repackaged Thorium will be shipped offsite to a predesignated repository again requiring remote operation

Development of instrumentation systems for severe accidents. 4. New accident tolerant in-containment pressure transducer for containment pressure monitoring system

International Nuclear Information System (INIS)

Oba, Masato; Teruya, Kuniyuki; Yoshitsugu, Makoto; Ikeuchi, Takeshi

2015-01-01

The accident at Tokyo Electric Power Company's Fukushima Dai-ichi Nuclear Power Plant (TF-1 accident) caused severe situations and resulted in a difficulty in measuring important parameters for monitoring plant conditions. Therefore, we have studied the TF-1 accident to select the important parameters that should be monitored at the severe accident and are developing the Severe Accident Instrumentations and Monitoring Systems that could measure the parameters in severe accident conditions. Mitsubishi Heavy Industries, LTD (MHI) developed a new accident tolerant containment pressure monitoring system and demonstrated that the monitoring system could endure extremely harsh environmental conditions that envelop severe accident environmental conditions inside a containment such as maximum operating temperature of up to 300degC and total integrated dose (TID) of 1 MGy gamma. The new containment pressure monitoring system comprises of a strain gage type pressure transducer and a mineral insulated (MI) cable with ceramic connectors, which are located in the containment, and a strain measuring amplifier located outside the containment. Less thermal and radiation degradation is achieved because of minimizing use of organic materials for in-containment equipment such as the transducer and connectors. Several tests were performed to demonstrate the performance and capability of the in-containment equipment under severe accident environmental conditions and the major steps in this testing were run in the following test sequences: (1) the baseline functional tests (e.g., repeatability, non-linearity, hysteresis, and so on) under normal conditions, (2) accident radiation testing, (3) seismic testing, and (4) steam/temperature test exposed to simulated severe accident environmental conditions. The test results demonstrate that the new pressure transducer can endure the simulated severe accident conditions. (author)

Anthropogenic materials and products containing natural radionuclides. Pt. 1a. Radiation properties of raw materials and waste materials. A literature study

International Nuclear Information System (INIS)

Reichelt, A.; Roehrer, J.; Lehmann, K.H.

1995-12-01

Cased on the literature study, the publication presents relevant data on raw materials and wastes containing natural radionuclides. The study is part 1a of the project on ''Anthropogenic materials and waste materials containing natural radionuclides''. Part 1 of the project gives data and information on about 100 different materials and wastes or products for household or industrial applications which contain significant amounts of natural radioactivity. In addition, part 1 presents for some of these materials information on their applications, consumption, radioactivity and resulting radiation doses. The raw materials and waste materials on the list in part 1 are characterised in this 1a report. Wherever appropriate, two or more materials are dealt with in one chapter, as e.g. felspar and felspar sands (pegmatite), talcum, and soapstone. The wastes are dealt with in the chapters discussing the relevant raw materials. The information given is as derived from the literature and does not include comments or evaluation by the authors of this report. Whenever the literature study did not yield information on radiological aspects of a material on the list, an appropriate notice is given. (Orig./DG) [de

Preparation and multi-properties determination of radium-containing rocklike material

Science.gov (United States)

Hong, Changshou; Li, Xiangyang; Zhao, Guoyan; Jiang, Fuliang; Li, Ming; Zhang, Shuai; Wang, Hong; Liu, Kaixuan

2018-02-01

The radium-containing rocklike material were fabricated using distilled water, ordinary Portland cement and additives mixed aggregates and admixtures according to certain proportion. The physico-mechanical properties as well as radioactive properties of the prepared rocklike material were measured. Moreover, the properties of typical granite sample were also investigated. It is found on one hand, similarities exist in physical and mechanical properties between the rocklike material and the granite sample, this confirms the validity of the proposed method; on the other hand, the rocklike material generally performs more remarkable radioactive properties compared with the granite sample, while radon diffusive properties in both materials are essentially matching. This study will provide a novel way to prepare reliable radium-containing samples for radon study of underground uranium mine.

Material control test and evaluation system at the ICPP

International Nuclear Information System (INIS)

Johnson, C.E.

1979-01-01

The US DOE is evaluating process monitoring as part of a total nuclear material safeguards system. A monitoring system is being installed at the Idaho Chemical Processing Plant to test and evaluate material control and surveillance concepts in an operating nuclear fuel reprocessing plant. Process monitoring for nuclear material control complements conventional safeguards accountability and physical protection to assure adherence to approved safeguards procedures and verify containment of nuclear materials within the processing plant

Container material and design considerations for storage of low-level radioactive waste

International Nuclear Information System (INIS)

Temus, C.J.

1987-01-01

With the threat of increased burial site restrictions and increased surcharges; the ease with which waste is sent to the burial site has been reduced. For many generators of waste the only alternative after maximizing volume reduction efforts is to store the waste. Even after working through the difficult decision of deciding what type of storage facility to have, the decision of what type of container to store the waste in has to still be made. This paper explores the many parameters that affect not only the material selection but also the design. The proper selection of materials affect the ability of the container to survive the storage period. The material selection also directly affects the design and utilization of the storage facility. The impacts to the facility include the functional aspects as well as its operational cost and liability as related to such things as fire insurance and active environmental control systems. The advantages and disadvantages of many of the common systems such as carbon steel, various coatings, polyethylene, stainless steel, composites and concrete will be discussed and evaluated. Recognizing that the waste is to be disposed of in the future differentiates it from waste that is shipped directly to the disposal site. The stored waste has to have the capability to be handled not only once like the disposal site waste but potentially several times before ultimate disposal. This handling may be by several different systems both at the storage facility and the burial site. Some of these systems due to ALARA considerations are usually remote requiring various interfaces, while not interfering with handling, transportation or disposal operations

Contained x-ray diffraction goniometer for examination of radioactive materials

International Nuclear Information System (INIS)

Smith, P.K.; Osgood, B.C.; Blaser, D.E.; Howell, R.E.; Stuhler, H.; Stauver, J.

1987-11-01

Radioactive materials are being characterized for chemical form and certain physical properties with an x-ray diffraction goniometer customized for containment in a shielded alpha glovebox. A Siemens D500 goniometer was customized by Siemens to locate the associated electronics and x-ray generator outside the glovebox to minimize corrosion and facilitate maintenance. A graphite monochromator is used with a shielded scintillation detector to separate diffracted x-radiation from nuclear radiation. The diffraction system is computer automated for data acquisition and reduction. The facility is designed to handle primarily alpha- and beta-emitting samples with moderate neutron and gamma radiation. Samples containing plutonium, enriched uranium, and other transuranic elements are analyzed in support of site nuclear operations and development programs on nuclear waste, chemical separations, reactor fuels, and product forms

On material and energy sources of formation of fuel-containing materials during Chernobyl NPP UNIT 4 accident

Directory of Open Access Journals (Sweden)

O. V. Mikhailov

2016-12-01

Full Text Available Results of detailed analysis of material substance of lava-like fuel-containing materials sources (FCM and clusters with high uranium concentration were presented. Material and energy balance are aggregated in a process model for optimal composition of sacrificial materials and FCM. Quantitative estimate is given for spent nuclear fuel’ afterheat in a number of other heat energy sources in reactor vault. Conclusion was made that upon condition of 50 % heat loss, remained amount of “useful” heat would be sufficient for proceeding of blast furnace version of fuel-containing materials.

Glucose from a cellulose-containing raw material

Energy Technology Data Exchange (ETDEWEB)

Feniksova, R V

1977-01-01

Glucose was produced by mixing the raw material with an enzyme and water, enzymic hydrolysis of raw material, and separation of the hydrolyzate. To increase the yield of glucose, the hydrolysis took place in 2 stages: at the 1st stage, the hydrolysis was continued until the mixture of glucose and oligosaccharides was obtained under the influence of an active enzyme (1 to 20 units/g of cellulose present in the raw material); at the 2nd stage, cellulase immobilized on an insoluble carrier (by covalent bonds) was used for the hydrolysis of oligosaccharides. The hydromodulus of the suspension of cellulose-containing raw material was maintained 5 to 30. A carrier nonhydrolyzable by cellulase, for instance a homogenious macroporous Aerosil gel, a porous glass, or porous ceramics, was used.

Researches of real observation geometry in monitoring fuel-containing materials' subcriticality

International Nuclear Information System (INIS)

Vysotskij, E.D.; Shevchenko, V.G.; Shevchenko, M.V.

2002-01-01

The effectiveness of fuel-containing materials monitoring is discussed in the part related to the feasibilities of researches and realization of optimal geometry (detectors - source) of survey of neutron activity dynamics in nuclearly hazardous areas with clusters of fuel-containing materials concentrated in the premises 305/2

Container for storage of environmental incompatible materials

International Nuclear Information System (INIS)

Ruggenthaler, P.T.

1984-01-01

The container consists of a cuboid chamber, closed to five sides, just as the cover made of concrete. Iron mountings for use with lifting gears are coupled with the armouring of the container. The cover is made in such a way that mountings are hidden by the recesses at its borders. Therefore it is possible to stick these boxes. Concrete employed for is enriched with sealing materials of synthetics, the box is painted too. Sensors on the outside ensure telemetering of closeness of the boxes. (J.K.) [de

Ensuring the 50 year life of a fissile material container

International Nuclear Information System (INIS)

Glass, R.E.; Towne, T.L.

1997-12-01

Sandia was presented with an opportunity in 1993 to design containers for the long term storage and transport of fissile material. This program was undertaken at the direction of the US Department of Energy and in cooperation with Lawrence Livermore National Laboratory and Los Alamos National Laboratory which were tasked with developing the internal fixturing for the contents. The hardware is being supplied by Allied Signal Federal Manufacturing and Technologies, and the packaging will occur at Mason and Hangar Corporation's Pantex Plant. The unique challenge was to design a container that could be sealed with the fissile material contents; and, anytime during the next 50 years, the container could be transported with only the need for the pre-shipment leak test. This required not only a rigorous design capable of meeting the long term storage and transportation requirements, but also resulted in development of a surveillance program to ensure that the container continues to perform as designed over the 50-year life. This paper addresses the design of the container, the testing that was undertaken to demonstrate compliance with US radioactive materials transport regulations, and the surveillance program that has been initiated to ensure the 50-year performance

Determination of Fire Enviroment in Stacked Cargo Containers with Radioactive Materials Packages

Energy Technology Data Exchange (ETDEWEB)

Arviso, M.; Bobbe, J.G.; Dukart, R.D.; Koski, J.A.

1999-05-01

Results from a Fire Test with a three-by-three stack of standard 6 m long International Standards Organization shipping containers containing combustible fuels and empty radioactive materials packages are reported and discussed. The stack is intended to simulate fire conditions that could occur during on-deck stowage on container cargo ships. The fire is initated by locating the container stack adjacent to a 9.8 x 6 m pool fire. Temperatures of both cargoes (empty and simulated radioactive materials packages) and containers are recorded and reported. Observations on the duration, intensity and spread of the fire are discussed. Based on the results, models for simulation of fire exposure of radioactive materials packages in such fires are suggested.

Immobilization of INEL low-level radioactive wastes in ceramic containment materials

International Nuclear Information System (INIS)

Seymour, W.C.; Kelsey, P.V.

1978-11-01

INEL low-level radioactive wastes have an overall chemical composition that lends itself to self-containment in a ceramic-based material. Fewer chemical additives would be needed to process the wastes than to process high-level wastes or use a mixture containment method. The resulting forms of waste material could include a basalt-type glass or glass ceramic and a ceramic-type brick. Expected leach resistance is discussed in relationshp to data found in the literature for these materials and appears encouraging. An overview of possible processing steps for the ceramic materials is presented

A Review of Removable Surface Contamination on Radioactive Materials Transportation Containers

Energy Technology Data Exchange (ETDEWEB)

Kennedy, Jr, W. E.; Watson, E. C.; Murphy, D. W.; Harrer, B. J.; Harty, R.; Aldrich, J. M.

1981-05-01

This report contains the results of a study sponsored by the U.S. Nuclear Regulatory Commission (NRC) of removable surface contamination on radioactive materials transportation containers. The purpose of the study is to provide information to the NRC during their review of existing regulations. Data was obtained from both industry and literature on three major topics: 1) radiation doses, 2) economic costs, and 3) contamination frequencies. Containers for four categories of radioactive materials are considered including radiopharmaceuticals, industrial sources, nuclear fuel cycle materials, and low-level radioactive waste. Assumptions made in this study use current information to obtain realistic yet conservative estimates of radiation dose and economic costs. Collective and individual radiation doses are presented for each container category on a per container basis. Total doses, to workers and the public, are also presented for spent fuel cask and low-level waste drum decontamination. Estimates of the additional economic costs incurred by lowering current limits by factors of 10 and 100 are presented. Current contamination levels for each category of container are estimated from the data collected. The information contained in this report is designed to be useful to the NRC in preparing their recommendations for new regulations.

19 CFR 10.540 - Packing materials and containers for shipment.

Science.gov (United States)

2010-04-01

...-Singapore Free Trade Agreement Rules of Origin § 10.540 Packing materials and containers for shipment. (a... the United States. Accordingly, in applying either the build-down or build-up method for determining... shipping container which it purchased from Company B in Singapore. The shipping container is originating...

Container materials for isolation of radioactive waste in salt

International Nuclear Information System (INIS)

Streicher, M.A.; Andrews, A.

1987-10-01

The workshop reviewed the extensive data on the corrosion resistance of low-carbon steel in simulated salt repository environments, determined whether these data were sufficient to recommend low-carbon steel for fabrication of the container, and assessed the suitability of other materials under consideration in the SRP. The panelists determined the need for testing and research programs, recommended experimental approaches, and recommended materials based on existing technology. On the first day of the workshop, presentations were made on waste package requirements; the expected corrosion environment; degradation processes, including a review of data from corrosion tests on carbon steel; and rationales for container design and materials, modeling studies, and planned future work. The second day was devoted to a panel caucus, presentation of workshop findings, and open discussion. 76 refs., 2 figs., 3 tabs

Development on design methodology of PWR passive containment system

International Nuclear Information System (INIS)

Lee, Seong Wook

1998-02-01

The containment is the most important barrier against the release of radioactive materials into the environment during accident conditions of nuclear power plants. Therefore the development of a reliable containment cooling system is one of key areas in advanced reactor development. To enhance the safety of the containment system, many new containment system designs have been proposed and developed in the world. Several passive containment cooling system (PCCS) concepts for both steel and concrete containment systems are overviewed and assessed comparatively. Major concepts considered are: (a) the spray of water on the outer surface of a steel containment from an elevated tank, (b) an external moat for a steel containment, (c) a suppression pool for a concrete containment, and (d) combination of the internal spray and internal or external condensers for a concrete containment. Emphasis is given to the heat removal principles, the required heat transfer area, system complexity and operational reliability. As one of conceptual design steps of containment, a methodology based on scaling principles is proposed to determine the containment size according to the power level. The AP600 containment system is selected as the reference containment to which the scaling laws are applied. Governing equations of containment pressure are set up in consideration of containment behavior in accident conditions. Then, the dimensionless numbers, which characterize the containment phenomena, are derived for the blowdown dominant and decay heat dominant stage, respectively. The important phenomena in blowdown stage are mass and energy sources and their absorption in containment atmosphere or containment structure, while heat transfer to the outer environment becomes important in decay heat stage. Based on their similarity between the prototype and the model, the containment sizes are determined for higher power levels and are compared with the SPWR containment design values available

Role of materials accounting in integrated safeguards systems for reprocessing plants

International Nuclear Information System (INIS)

Hakkila, E.A.; Gutmacher, R.G.; Markin, J.T.; Shipley, J.P.; Whitty, W.J.

1981-01-01

Integration of materials accounting and containment/surveillance techniques for international safeguards requires careful examination and definition of suitable inspector activities for verification of operator's materials accounting data. The inspector's verification procedures are designed to protect against data falsification and/or the use of measurement uncertainties to conceal missing material. Materials accounting activities are developed to provide an effective international safeguards system when combined with containment/surveillance activities described in a companion paper

Storage containers for radioactive material

International Nuclear Information System (INIS)

Cassidy, D.A.; Dates, L.R.; Groh, E.F.

1981-01-01

A radioactive material storage system is disclosed for use in the laboratory. This system is composed of the following: a flat base plate with a groove in one surface thereof and a hollow pedestal extending perpendicularly away from the other surface thereof; a sealing gasket in the groove, a cover having a filter therein and an outwardly extending flange which fits over the plate; the groove and the gasket, and a clamp for maintaining the cover and the plate are sealed together, whereby the plate and the cover and the clamp cooperate to provide a storage area for radioactive material readily accessible for use or inventory. Wall mounts are provided to prevent accidental formation of critical masses during storage

Comparison of solute-binding properties of plastic materials used as pharmaceutical product containers.

Science.gov (United States)

Jenke, Dennis; Couch, Tom; Gillum, Amy

2010-01-01

Material/water equilibrium binding constants (E(b)) were determined for 11 organic solutes and 2 plastic materials commonly used in pharmaceutical product containers (plasticized polyvinyl chloride and polyolefin). In general, solute binding by the plasticized polyvinyl chloride material was greater, by nearly an order of magnitude, than the binding by the polyolefin (on an equal weight basis). The utilization of the binding constants to facilitate container compatibility assessments (e.g., drug loss by container binding) for drug-containing products is discussed.

19 CFR 10.461 - Retail packaging materials and containers.

Science.gov (United States)

2010-04-01

... Free Trade Agreement Rules of Origin § 10.461 Retail packaging materials and containers. Packaging... classification set out in General Note 26(n), HTSUS. If the good is subject to a regional value content... non-originating materials, as the case may be, in calculating the regional value content of the good...

Heat-processing method and facility for helium-containing metal material

International Nuclear Information System (INIS)

Kato, Takahiko; Kodama, Hideyo; Matsumoto, Toshimi; Aono, Yasuhisa; Nagata, Tetsuya; Hattori, Shigeo; Kaneda, Jun-ya; Ono, Shigeki.

1996-01-01

Electric current is supplied to an objective portion of a He-containing metal material to be applied with heat processing without causing melting, to decrease the He content of the portion. Subsequently, the defect portion of the tissues of the He-containing metal is modified by heating the portion with melting. Since electric current can be supplied to the metal material in a state where the metal material is heated and the temperature thereof is elevated, an effect of further reducing the He content can be obtained. Further, if the current supply and/or the heating relative to the metal material is performed in a vacuum or inert gas atmosphere, an effect of reducing the degradation of the surface of the objective portion to be supplied with electric current can be obtained. (T.M.)

Impact of container material on the development of Aedes aegypti larvae at different temperatures.

Science.gov (United States)

Kumar, Gaurav; Singh, R K; Pande, Veena; Dhiman, R C

2016-01-01

Aedes aegypti, the primary vector of dengue generally breeds in intradomestic and peridomestic containers made up of different materials, i.e. plastic, iron, rubber, earthen material etc. The material of container is likely to affect the temperature of water in container with variation in environmental temperature. The present study was aimed to determine the effect of different container materials on larval development of Ae. aegypti at different temperatures. Newly hatched I instar larvae (2-4 h old) were used in the study and experiments were conducted using three different containers made up of plastic, iron and earthen material. Three replicates for each type of container at 22, 26, 30, 34, 38, 40, and 42°C were placed in environmental chamber for the development of larvae. At temperatures >22°C, 50% pupation was completed in earthen pot within 4.3±0.6 to 6.3±0.6 days followed by plastic containers (5±0 to 8±0 days) and iron containers (6±0 to 9±0 days). Developmental time for 50% pupation in the three containers differed significantly (p containers (p containers resulted in significant variations in the developmental period of larvae. More than 35°C temperature of water was found inimical for pupal development. The results revealed the variation in temperature of water in different types of containers depending on the material of container, affecting duration of larval development. As the larval development was faster in earthen pot as compared to plastic and iron containers, community should be discouraged for storing the water in earthen pots. However, in view of containers of different materials used by the community in different temperature zones in the country, further studies are required for devising area-specific preventive measures for Aedes breeding.

Survey of degradation modes of candidate materials for high-level radioactive-waste disposal containers

International Nuclear Information System (INIS)

Bullen, D.B.; Gdowski, G.E.

1988-08-01

Three copper-based alloys and three iron- to nickel-based austenitic alloys are being considered as possible materials for fabrication of high-level radioactive-waste disposal containers. The waste will include spent fuel assemblies from reactors as well as high-level waste in borosilicate glass and will be sent to the prospective site at Yucca Mountain, Nevada, for disposal. The copper-based alloy materials are CDA 102 (oxygen-free copper), CDA 613 (Cu-7Al), and CDA 715 (Cu-30Ni). The austenitic materials are Types 304L and 316L stainless steels and Alloy 825. The waste-package containers must maintain substantially complete containment for at least 300 yr and perhaps as long as 1000 yr, and they must be retrievable from the disposal site during the first 50 yr after emplacement. The containers will be exposed to high temperatures and high gamma radiation fields from the decay of high-level waste. This volume surveys the available data on the phase stability of both groups of candidate alloys. The austenitic alloys are reviewed in terms of the physical metallurgy of the iron-chromium-nickel system, martensite transformations, carbide formation, and intermetallic-phase precipitation. The copper-based alloys are reviewed in terms of their phase equilibria and the possibility of precipitation of the minor alloying constituents. For the austenitic materials, the ranking based on phase stability is: Alloy 825 (best), Type 316L stainless steel, and then Type 304L stainless steel (worst). For the copper-based materials, the ranking is: CDA 102 (oxygen-free copper) (best), and then both CDA 715 and CDA 613. 75 refs., 24 figs., 6 tabs

Manufacturing method for radioactive material containing vessel

International Nuclear Information System (INIS)

Kamino, Yoshikazu; Nishioka, Eiji; Toyota, Michinori.

1997-01-01

A containing vessel for radioactive materials (for example, spent fuels) comprises an inner cylinder made of stainless steel having a space for containing radioactive materials at the inside and an outer cylinder made of stainless steel disposed at the outer side of the inner cylinder. Lead homogenization is applied to a space between the inner and the outer cylinders to deposit a lead layer. Then, molten lead heated to a predetermined temperature is cast into the space between the inner and the outer cylinders. A valve is opened to discharge the molten lead in the space from a molten lead discharge pipe, and heated molten lead is injected from a molten lead supply pipe. Then, the discharge of the molten lead and the injection of the molten lead are stopped, and the lead in the space is coagulated. With such procedures, gaps are not formed between the lead of the homogenized portion and the lead of cast portion even when the thickness of the inner and the outer cylinders is great. (I.N.)

Advanced materials for space nuclear power systems

International Nuclear Information System (INIS)

Titran, R.H.; Grobstein, T.L.

1991-01-01

Research on monolithic refractory metal alloys and on metal matrix composites is being conducted at the NASA Lewis Research Center, Cleveland, Ohio, in support of advanced space power systems. The overall philosophy of the research is to develop and characterize new high-temperature power conversion and radiator materials and to provide spacecraft designers with material selection options and design information. Research on three candidate materials (carbide strengthened niobium alloy PWC-11 for fuel cladding, graphite fiber reinforced copper matrix composites (Gr/Cu) for heat rejection fins, and tungsten fiber reinforced niobium matrix composites (W/NB) for fuel containment and structural supports) considered for space power system applications is discussed. Each of these types of materials offers unique advantages for space power applications

FFTF-containment air-cleaning system

International Nuclear Information System (INIS)

Mahaffey, M.K.; Stepnewski, D.D.

1981-01-01

The FFTF Containment can accommodate all design basis events and the hypothetical core disruptive accident with adequate margin without a venting or purging system; however, in concert with the development objective, a system was designed and constructed to evaluate technology related to containment atmosphere venting and cleanup functions. The system can be used to purge high H 2 concentrations or to vent excessive containment pressure. In either case containment atmosphere is exhausted through an aqueous scrubber system consisting of a venturi scrubber and fibrous filter bank

Study of mechanoactivation of tungsten-molybdenum containing raw material in gas-jet mill

International Nuclear Information System (INIS)

Agnokov, T.Sh.; Gorobets, L.Zh.; Martynenko, V.P.; Fedorov, Yu.P.; Krakhmaleva, M.T.; Sokolova, L.A.

1988-01-01

Investigation is aimed at intensifying autoclave-soda leaching of tungsten-molybdenum-containing raw material. Connection of reactivity and physicochemical properties of crushed tungsten-molybdenum-containing products under different gas-jet crushing parameters is investigated. Optimal technological indices of hydrometallurgical reprocessing of tungsten-molybdenum-containing raw materials and products processed by gas-jet technique are given. The results obtained point out to perspectiveness of applying gas-jet technique of thermomechanical processing for intensifying and increasing the quality of tungsten- and molybdenum-containing raw materials and products of hydrometallurgical production

Use of the radiochemical method for identification of seized nuclear material - container

International Nuclear Information System (INIS)

Rosskopfova, O.; Matel, L.; Rajec, P.; Dobias, M.

2003-01-01

Analysis of the nuclear material of the seized illicit trafficking container was performed in the laboratory LARCHA. The container was professionally taken apart in the hot cell of HUMA-LAB APEKO. The compact core of container with mass of 36.00 kg was separated and analysed in the LARCHA laboratory. The results of alpha spectrometry proved that the core of container was made of depleted uranium. A suspicious container was seized, that was believed to be used for transportation of radioactive and nuclear materials. Container, according to Slovak Law, was transported to a Civil defence and police started with expertise analysis. On the basis of previous results, it was assumed that the core of the container was made of a nuclear material. The container was cut inside a hot cell to separate parts at HUMA-Lab Kosice and individual parts were prepared for analyses. From shape and type of the detained container it was assumed that the core of the container was made of depleted uranium and suspected cut pieces were sent to the accredited laboratory LARCHA Bratislava for isotope analysis. Samples from different parts of the container were analysed by using HPGe gamma. The results of gamma spectrometry proved the presence of Co-60, Cs-137 and U-235 with values 11.8 Bq, 5.6 Bq a 3.8 Bq respectively. On the basis of measured results it was calculated mass content (%) of uranium isotopes in samples. It was concluded that: - container is composed of different parts, which are made from steel, lead and uranium; - the wipe tests proved the presence of radionuclides of Cs-137 and Co-60; - the core of the container is made of depleted uranium; - chosen methods, which were used proved that are suitable for analysis and identification of nuclear materials. (authors)

Remote-Reading Safety and Safeguards Surveillance System for 3013 Containers

International Nuclear Information System (INIS)

Lechelt, W. M.; Skorpik, J. R.; Silvers, K. L.; Szempruch, R. W.; Douglas, D. G.; Fein, K. O.

2002-01-01

At Hanford's Plutonium Finishing Plant (PFP), plutonium oxide is being loaded into stainless steel containers for long-term storage on the Hanford Site. These containers consist of two weld-sealed stainless steel cylinders nested one within the other. A third container holds the plutonium within the inner cylinder. This design meets the U.S. Department of Energy (DOE) storage standard, DOE-STD- 3013-2000, which anticipates a 50-year storage lifetime. The 3013 standard also requires a container surveillance program to continuously monitor pressure and to assure safeguards are adequate. However, the configuration of the container system makes using conventional measurement and monitoring methods difficult. To better meet the 3013 monitoring requirements, a team from Fluor Hanford (who manages the PFP), Pacific Northwest National Laboratory (PNNL), and Vista Engineering Technologies, LLC, developed a safer, cost-efficient, remote PFP 3013 container surveillance system. This new surveillance system is a combination of two successfully deployed technologies: (1) a magnetically coupled pressure gauge developed by Vista Engineering and (2) a radio frequency (RF) tagging device developed by PNNL. This system provides continuous, 100% monitoring of critical parameters with the containers in place, as well as inventory controls. The 3013 container surveillance system consists of three main elements: (1) an internal magnetic pressure sensor package, (2) an instrument pod (external electronics package), and (3) a data acquisition storage and display computer. The surveillance system described in this paper has many benefits for PFP and DOE in terms of cost savings and reduced personnel exposure. In addition, continuous safety monitoring (i.e., internal container pressure and temperature) of every container is responsible nuclear material stewardship and fully meets and exceeds DOE's Integrated Surveillance Program requirements

New CSA guideline for the exemption or clearance from regulatory control of materials that contain, or potentially contain, nuclear substances

International Nuclear Information System (INIS)

Rhodes, M.; Kwong, A.

2011-01-01

The Canadian Standards Association (CSA) guideline N292.5, Guideline for the exemption or clearance from regulatory control of materials that contain, or potentially contain, nuclear substances, was recently developed to address a need for guidance on approaches for clearance of materials from facilities licensed by the Canadian Nuclear Safety Commission (CNSC) consistent with Canadian and international recommendations. This guideline is also applicable to determining if an activity associated with materials that contain nuclear substances is exempt from requiring a CNSC licence. The guideline summarizes the regulatory requirements associated with the exemption and clearance of materials and provides a graded approach to designing a survey based on the risk of residual contamination being present. (author)

Remote operation system for container

International Nuclear Information System (INIS)

Nakahara, Hirotaka; Hayata, Takashi; Kajiyama, Shigeru; Takahashi, Fuminobu

1998-01-01

The present invention provides a remote operation system for conducting operation with operation reaction for the inside of a container filled with water (liquid), such as of inner walls and inner structural materials of a BWR type reactor. Namely, a swimming robot comprises a swimming device swimming in the liquid and an attaching/detaching device for holding/releasing the handling robot. A control device remotely operate the swimming robot and the handling robot by way of a cable. A cable processing device takes up or dispenses the cable. In addition, when the swimming robot grasps the handling robot by the attaching/detaching device, the swimming robot transmits an operation instruction sent from the control device by way of the cable to the handling robot. After the attaching/detaching device of the swimming robot releases the handling robot, the handling robot operates based on the transmitted operation instruction. It is preferable that the handling robot has an adsorptive moving device for moving itself while being adsorbed on the wall surface of the container. (I.S.)

Preliminary selection criteria for the Yucca Mountain Project waste package container material

International Nuclear Information System (INIS)

Halsey, W.G.

1991-01-01

The Department of Energy's Yucca Mountain Project (YMP) is evaluating a site at Yucca Mountain in Nevada for construction of a geologic repository for the storage of high-level nuclear waste. Lawrence Livermore National Laboratory's (LLNL) Nuclear Waste Management Project (NWMP) has the responsibility for design, testing, and performance analysis of the waste packages. The design is performed in an iterative manner in three sequential phases (conceptual design, advanced conceptual design, and license application design). An important input to the start of the advanced conceptual design is the selection of the material for the waste containers. The container material is referred to as the 'metal barrier' portion of the waste package, and is the responsibility of the Metal Barrier Selection and Testing task at LLNL. The selection will consist of several steps. First, preliminary, material-independent selection criteria will be established based on the performance goals for the container. Second, a variety of engineering materials will be evaluated against these criteria in a screening process to identify candidate materials. Third, information will be obtained on the performance of the candidate materials, and final selection criteria and quantitative weighting factors will be established based on the waste package design requirements. Finally, the candidate materials will be ranked against these criteria to determine whether they meet the mandated performance requirements, and to provide a comparative score to choose the material for advanced conceptual design activities. This document sets forth the preliminary container material selection criteria to be used in screening candidate materials. 5 refs

Hearth furnace for distilling powdered materials containing hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

1937-06-21

The present invention has for its object a hearth furnace particularly intended for the distillation of powdered material containing hydrocarbons. It consists of a fixed circular hearth above which are placed the moving scrapers intended to displace the material from the center toward the periphery. The material is poured by a central vertical pipe at the base of which is arranged a rotating ring for distributing the material on the hearth; this ring, which is fastened on the vertical axis of the drive, carries the radial arms to which are attached the scrapers arranged obliquely by the support on the arms and intended to displace the material on the hearth. The hearth is heated from below by means of forced circulation of gases produced in a fire-box and maintained at a convenient temperature by mixing with a part of the cold gases.

Radiation Shielding Materials Containing Hydrogen, Boron, and Nitrogen: Systematic Computational and Experimental Study. Phase I

Science.gov (United States)

Thibeault, Sheila A.; Fay, Catharine C.; Lowther, Sharon E.; Earle, Kevin D.; Sauti, Godfrey; Kang, Jin Ho; Park, Cheol; McMullen, Amelia M.

2012-01-01

The key objectives of this study are to investigate, both computationally and experimentally, which forms, compositions, and layerings of hydrogen, boron, and nitrogen containing materials will offer the greatest shielding in the most structurally robust combination against galactic cosmic radiation (GCR), secondary neutrons, and solar energetic particles (SEP). The objectives and expected significance of this research are to develop a space radiation shielding materials system that has high efficacy for shielding radiation and that also has high strength for load bearing primary structures. Such a materials system does not yet exist. The boron nitride nanotube (BNNT) can theoretically be processed into structural BNNT and used for load bearing structures. Furthermore, the BNNT can be incorporated into high hydrogen polymers and the combination used as matrix reinforcement for structural composites. BNNT's molecular structure is attractive for hydrogen storage and hydrogenation. There are two methods or techniques for introducing hydrogen into BNNT: (1) hydrogen storage in BNNT, and (2) hydrogenation of BNNT (hydrogenated BNNT). In the hydrogen storage method, nanotubes are favored to store hydrogen over particles and sheets because they have much larger surface areas and higher hydrogen binding energy. The carbon nanotube (CNT) and BNNT have been studied as potentially outstanding hydrogen storage materials since 1997. Our study of hydrogen storage in BNNT - as a function of temperature, pressure, and hydrogen gas concentration - will be performed with a hydrogen storage chamber equipped with a hydrogen generator. The second method of introducing hydrogen into BNNT is hydrogenation of BNNT, where hydrogen is covalently bonded onto boron, nitrogen, or both. Hydrogenation of BN and BNNT has been studied theoretically. Hyper-hydrogenated BNNT has been theoretically predicted with hydrogen coverage up to 100% of the individual atoms. This is a higher hydrogen content

Accumulation of organic compounds leached from plastic materials used in biopharmaceutical process containers.

Science.gov (United States)

Jenke, Dennis R; Zietlow, David; Garber, Mary Jo; Sadain, Salma; Reiber, Duane; Terbush, William

2007-01-01

Plastic materials are widely used in medical items, such as solution containers, transfusion sets, transfer tubing, and devices. An emerging trend in the biotechnology industry is the utilization of plastic containers to prepare, transport, and store an assortment of solutions including buffers, media, and in-process and finished product. The direct contact of such containers with the product at one or more points in its lifetime raises the possibility that container leachables may accumulate in the finished product. The interaction between several commercially available container materials and numerous model test solutions (representative of buffers and media used in biopharmaceutical applications) was investigated. This paper summarizes the identification of leachables associated with the container materials and documents the levels to which targeted leachables accumulate in the test solutions under defined storage conditions.

An annotated history of container candidate material selection

International Nuclear Information System (INIS)

McCright, R.D.

1988-07-01

This paper documents events in the Nevada Nuclear Waste Storage Investigations (NNWSI) Project that have influenced the selection of metals and alloys proposed for fabrication of waste package containers for permanent disposal of high-level nuclear waste in a repository at Yucca Mountain, Nevada. The time period from 1981 to 1988 is covered in this annotated history. The history traces the candidate materials that have been considered at different stages of site characterization planning activities. At present, six candidate materials are considered and described in the 1988 Consultation Draft of the NNWSI Site Characterization Plan (SCP). The six materials are grouped into two alloy families, copper-base materials and iron to nickel-base materials with an austenitic structure. The three austenitic candidates resulted from a 1983 survey of a longer list of candidate materials; the other three candidates resulted from a special request from DOE in 1984 to evaluate copper and copper-base alloys. 24 refs., 2 tabs

Equilibrium leach tests with cobalt in the system cemented waste form/container material/aqueous solution

International Nuclear Information System (INIS)

Vejmelka, P.; Koester, R.; Lee, M. J.; Han, K. W.

1991-01-01

The equilibrium concentrations of Co in the system of cemented waste form/aqueous solutions were determined including the effect of the container material and its corrosion products under the respective conditions. The chemical conditions in the near field of the waste form were characterized by measurement of the pH and E h value. As disposal relevant solutions, saturated sodium chloride, Q-brine (main constituent MgCl 2 ) and a granitic type groundwater were used. For comparison, also experiments using deionized water were performed. In all systems investigated the cemented waste form itself has a strong influence on the chemical conditions in the near field. The pH and E h values are affected in all cases by the addition of the cemented waste form. There is no or only a slight difference between the E h values if iron powder or iron hydroxide is added to the cemented waste form/solution systems, but the E h is markedly decreased when iron powder is added to the solution free of cement. The Co concentration is decreased in all solutions by the addition of the cemented waste form, the largest effect is observed in Q-brine and this can be attributed either to the sorption of the Co-ions on the corrosion products of the cement or to the coprecipitation of Co-hydroxide and Mg-hydroxide. In the other solutions the Co concentration is decreased by precipitation of Co-hydroxide due to the high pH value of 12.5, and the concentrations are comparable for the different solutions

Properies of binder systems containing cement, fly ash, and limestone powder

Directory of Open Access Journals (Sweden)

Krittiya Kaewmanee

2014-10-01

Full Text Available Fly ash and limestone powder are two major widely available cement replacing materials in Thailand. However, the current utilization of these materials is still not optimized due to limited information on properties of multi-binder systems. This paper reports on the mechanical and durability properties of mixtures containing cement, fly ash, and limestone powder as single, binary, and ternary binder systems. The results showed that a single binder system consisting of only cement gave the best carbonation resistance. A binary binder system with fly ash exhibited superior performances in long-term compressive strength and many durability properties except carbonation and magnesium sulfate resistances, while early compressive strength of a binary binder system with limestone powder was excellent. The ternary binder system, taking the most benefit of selective cement replacing materials, yielded, though not the best, satisfactory performances in almost all properties. Thus, the optimization of binders can be achieved through a multi-binder system.

Direct containment heating experiments in Zion Nuclear Power Plant geometry using prototypic materials

International Nuclear Information System (INIS)

Binder, J.L.; McUmber, L.M.; Spencer, B.W.

1993-01-01

Direct Containment Heating (DCH) experiments have been completed which utilize prototypic core materials. The experiments reported on here are a continuation of the Integral Effects Testing (IET) DCH program. The experiments incorporated a 1/40 scale model of the Zion Nuclear Power Plant containment structures. The model included representations of the primary system volume, RPV lower head, cavity and instrument tunnel, and the lower containment structures. The experiments were steam driven. Iron-alumina thermite with chromium was used as a core melt stimulant in the earlier IET experiments. These earlier IET experiments at Argonne National Laboratory (ANL) and Sandia National Laboratories (SNL) provided useful data on the effect of scale on DCH phenomena; however, a significant question concerns the potential experiment distortions introduced by the use of non-prototypic iron/alumina thermite. Therefore, further testing with prototypic materials has been carried out at ANL. Three tests have been completed, DCH-U1A, U1B and U2. DCH-U1A and U1B employed an inerted containment atmosphere and are counterpart to the IET-1RR test with iron/alumina thermite. DCH-U2 employed nominally the same atmosphere composition of its counterpart iron/alumina test, IET-6. All tests, with prototypic material, have produced lower peak containment pressure rises; 45, 111 and 185 kPa in U1A, U1B and U2, compared to 150 and 250 kPa IET-1RR and 6. Hydrogen production, due to metal-steam reactions, was 33% larger in U1B and U2 compared to IET-1RR and IET-6. The pressurization efficiency was consistently lower for the corium tests compared to the IET tests

Modification of clay-based waste containment materials

International Nuclear Information System (INIS)

Adu-Wusu, K.; Whang, J.M.; McDevitt, M.F.

1997-01-01

Bentonite clays are used extensively for waste containment barriers to help impede the flow of water in the subsurface because of their low permeability characteristics. However, they do little to prevent diffusion of contaminants, which is the major transport mechanism at low water flows. A more effective way of minimizing contaminant migration in the subsurface is to modify the bentonite clay with highly sorptive materials. Batch sorption studies were conducted to evaluate the sorptive capabilities of organo-clays and humic- and iron-based materials. These materials proved to be effective sorbents for the organic contaminants 1,2,4-trichlorobenzene, nitrobenzene, and aniline in water, humic acid, and methanol solution media. The sorption capacities were several orders of magnitude greater than that of unmodified bentonite clay. Modeling results indicate that with small amounts of these materials used as additives in clay barriers, contaminant flux through walls could be kept very small for 100 years or more. The cost of such levels of additives can be small compared to overall construction costs

Detection of tiny amounts of fissile materials in large-sized containers with radioactive waste

Science.gov (United States)

Batyaev, V. F.; Skliarov, S. V.

2018-01-01

The paper is devoted to non-destructive control of tiny amounts of fissile materials in large-sized containers filled with radioactive waste (RAW). The aim of this work is to model an active neutron interrogation facility for detection of fissile ma-terials inside NZK type containers with RAW and determine the minimal detectable mass of U-235 as a function of various param-eters: matrix type, nonuniformity of container filling, neutron gen-erator parameters (flux, pulse frequency, pulse duration), meas-urement time. As a result the dependence of minimal detectable mass on fissile materials location inside container is shown. Nonu-niformity of the thermal neutron flux inside a container is the main reason of the space-heterogeneity of minimal detectable mass in-side a large-sized container. Our experiments with tiny amounts of uranium-235 (<1 g) confirm the detection of fissile materials in NZK containers by using active neutron interrogation technique.

Detection of tiny amounts of fissile materials in large-sized containers with radioactive waste

Directory of Open Access Journals (Sweden)

Batyaev V.F.

2018-01-01

Full Text Available The paper is devoted to non-destructive control of tiny amounts of fissile materials in large-sized containers filled with radioactive waste (RAW. The aim of this work is to model an active neutron interrogation facility for detection of fissile ma-terials inside NZK type containers with RAW and determine the minimal detectable mass of U-235 as a function of various param-eters: matrix type, nonuniformity of container filling, neutron gen-erator parameters (flux, pulse frequency, pulse duration, meas-urement time. As a result the dependence of minimal detectable mass on fissile materials location inside container is shown. Nonu-niformity of the thermal neutron flux inside a container is the main reason of the space-heterogeneity of minimal detectable mass in-side a large-sized container. Our experiments with tiny amounts of uranium-235 (<1 g confirm the detection of fissile materials in NZK containers by using active neutron interrogation technique.

Analysis on the effect of risk from containment failure by over-pressurization during the operation of containment filtered venting system

International Nuclear Information System (INIS)

Ham, Jaehyun; Kang, Hyun Gook; Chang, Soon Heung

2015-01-01

Passive safety systems which are operated without power source are suggested as a solution SBO. For containment protection system, Containment Filtered Venting System (CFVS) is suggested. CFVS controls the containment pressure by releasing the containment gas through filter passively without any power source. But because still small amount of radioactive material have no choice but to release to the environment, starting time and operation method of CFVS have to be determined carefully. Later starting time brings not only lower release but also higher risk from containment failure by over-pressurization, so it is a problem. In this research, the effect of risk from containment failure by over-pressurization during the operation of containment filtered venting system was analyzed. In this research, optimized values for variables of the CFVS operation method are found as 0.67 MPa, 9 cm, 0.1 MPa each for open pressure, pressure interval, and vent pipe diameter when DF as a function of time and risk from containment over-pressurization failure are considered. Generally in this research, release without risk get lower values in higher pressure, and lower vent pipe diameter. Release with risk get sharply high values when the containment pressure exceeds the design pressure because of the effect of risk from containment failure by over-pressurization. In conclusion, highest pressure, and lowest vent pipe diameter which are not influenced by risk is the optimized values for CFVS operation method because amount of risk is much larger than release through the CFVS

Authenticated Secure Container System (ASCS)

International Nuclear Information System (INIS)

1991-01-01

Sandia National Laboratories developed an Authenticated Secure Container System (ASCS) for the International Atomic Energy Agency (IAEA). Agency standard weights and safeguards samples can be stored in the ASCS to provide continuity of knowledge. The ASCS consists of an optically clear cover, a base containing the Authenticated Item Monitoring System (AIMS) transmitter, and the AIMS receiver unit for data collection. The ASCS will provide the Inspector with information concerning the status of the system, during a surveillance period, such as state of health, tampering attempts, and movement of the container system. The secure container is located inside a Glove Box with the receiver located remotely from the Glove Box. AIMS technology uses rf transmission from the secure container to the receiver to provide a record of state of health and tampering. The data is stored in the receiver for analysis by the Inspector during a future inspection visit. 2 refs

Containment vessel drain system

Science.gov (United States)

Harris, Scott G.

2018-01-30

A system for draining a containment vessel may include a drain inlet located in a lower portion of the containment vessel. The containment vessel may be at least partially filled with a liquid, and the drain inlet may be located below a surface of the liquid. The system may further comprise an inlet located in an upper portion of the containment vessel. The inlet may be configured to insert pressurized gas into the containment vessel to form a pressurized region above the surface of the liquid, and the pressurized region may operate to apply a surface pressure that forces the liquid into the drain inlet. Additionally, a fluid separation device may be operatively connected to the drain inlet. The fluid separation device may be configured to separate the liquid from the pressurized gas that enters the drain inlet after the surface of the liquid falls below the drain inlet.

19 CFR 10.602 - Packing materials and containers for shipment.

Science.gov (United States)

2010-04-01

...-Central America-United States Free Trade Agreement Rules of Origin § 10.602 Packing materials and... regional value content calculation. Packing materials and containers for shipment, as defined in § 10.593(m) of this subpart, are to be disregarded in determining the regional value content of a good imported...

Corrosion of candidate container materials by Yucca Mountain bacteria

International Nuclear Information System (INIS)

Horn, J; Jones, D; Lian, T; Martin, S; Rivera, A

1999-01-01

Several candidate container materials have been studied in modified Yucca Mountain (YM) ground water in the presence or absence of YM bacteria. YM bacteria increased corrosion rates by 5-6 fold in UNS G10200 carbon steel, and nearly 100-fold in UNS NO4400 Ni-Cu alloy. YM bacteria caused microbiologically influenced corrosion (MIC) through de-alloying or Ni-depletion of Ni-Cu alloy as evidenced by scanning electronic microscopy (SEM) and inductively coupled plasma spectroscopy (ICP) analysis. MIC rates of more corrosion-resistant alloys such as UNS NO6022 Ni-Cr- MO-W alloy, UN's NO6625 Ni-Cr-Mo alloy, and UNS S30400 stainless steel were measured below 0.05 umyr, however YM bacteria affected depletion of Cr and Fe relative to Ni in these materials. The chemical change on the metal surface caused by depletion was characterized in anodic polarization behavior. The anodic polarization behavior of depleted Ni-based alloys was similar to that of pure Ni. Key words: MIC, container materials, YM bacteria, de-alloying, Ni-depletion, Cr-depletion, polarization resistance, anodic polarization,

A filter system for steam-gas mixture ejections from under a nuclear reactor containment following a severe accident

International Nuclear Information System (INIS)

Dulepov, Ju. N.; Sharygin, L. M.; Tretjakov, S. Ja.; Shtin, A.P.; Glushko, V. V.; Babenko, E. A.; Kurakov, Ju. A.

1997-01-01

In this paper newly built NPPs obligatory incorporate a containment having a filter system for removing radioactive materials ejections under severe accidents including nuclear fuel melting is described. The system prevents a containment failure and provides ejected radioactive materials decontamination to permissible levels. The physical-chemical and chemical characteristics of Termoxid-58 sorbent (TiO 5 based sorbent) are presented

Fluorine uptake into the human enamel surface from fluoride-containing sealing materials during cariogenic pH cycling

Science.gov (United States)

Yasuhiro, Matsuda; Katsushi, Okuyama; Hiroko, Yamamoto; Hisanori, Komatsu; Masashi, Koka; Takahiro, Sato; Naoki, Hashimoto; Saiko, Oki; Chiharu, Kawamoto; Hidehiko, Sano

2015-04-01

To prevent the formation of caries and reduce dentin hypersensitivity, sealing materials, either with or without fluoride, are generally applied on the tooth in clinical practice. Application of fluoride-free sealing materials results in the formation of an acid-resistant layer on the tooth surface. On the other hand, fluoride-containing sealing materials might not only form an acid-resistant layer but could possibly further provide fluoride to enhance remineralization and reduce demineralization. In this study, the demineralization prevention ability and fluorine uptake rate in human enamel of fluoride-containing sealing materials ["MS coats F" (MSF)] and fluoride-free sealing materials ("hybrid coats 2" [HI]) were evaluated using an automatic pH cycling system. Each material was applied to the original tooth surface, the cut surfaces were covered with sticky wax, and the automatic pH-cycling system simulated daily acid changes (pH 6.8-4.5) occurring in the oral cavity for 4 weeks. Caries progression was analyzed using transverse microradiography (TMR) taken pre and post the 4 weeks of pH cycling. The fluorine and calcium distributions in the carious lesion in each specimen were evaluated using the proton-induced gamma emission (PIGE) and proton-induced X-ray (PIXE) techniques, respectively. TMR analysis showed that both MSF and HI had a caries-preventing effect after 4 weeks of pH cycling. PIGE/PIXE analysis demonstrated that only MSF resulted in fluoride uptake in the enamel surface. Therefore, MSF can help to form an acid-resistant layer and provide fluoride to the enamel surface. The presence of fluoride on the enamel surface suggested that MSF could prevent demineralization, even if the acid-resistant layer was removed, in clinical settings. The data obtained using the PIGE and PIXE techniques are useful for understanding the benefits of the use of a fluoride-containing sealing material for preventing caries.

Analysis of Depressurization Performance in Containment of Wolsong NPP Unit 1 through Containment Filtered Venting System

International Nuclear Information System (INIS)

Lee, Sunghan; Kim, Jinhyuck; Suh, Nam Duk; Cho, Songwon

2014-01-01

Containment filtered venting system (CFVS) is designed to open and to close isolation valves passively by an operator. CFVS is operated when the containment pressure exceeds the design pressure (225 kPa(a)) and is closed when the containment pressure decreases below 151 kPa(a). The aim of this study is to analyze the depressurization performance of Wolsong unit 1 through CFVS during SBO. The thermal-hydraulic behavior in containment of Wolsong unit 1 was evaluated using the MELCOR 1.8.6 code developed at Sandia National Laboratories (SNL) for the U.S. Nuclear Regulatory Commission (NRC). In addition, in order to evaluate the effects of the CFVS according to the venting area, a sensitivity study depending on different venting area of the CFVS was conducted. Finally, an analysis of the effects of filtering and scrubbing of radioactive material for CFVS is important but not treated in this paper. The SBO accident is chosen to analyze the thermal-hydraulic behavior of Wolsong unit 1. During SBO, the analysis of CFVS affecting on the depressurization of the containment was conducted using MELCOR 1.8.6 code. Also, a sensitivity study was carried out to evaluate the depressurization performance according to the venting area of CFVS. The results show that the containment pressure is considerably decreased and the integrity of the containment could be maintained in case of CFVS operating. Therefore, CFVS has the capacity to keep the containment pressure below the design pressure during SBO. In addition, there are large differences in the containment pressure depending on venting area. We found that the decreasing rate of the pressure in the containment and water level in CFVS depends on the venting area. In the future, a proper requirement for CFVS sizing criteria according to accident scenarios such as LBLOCA, SBLOCA and SGTR, etc. should be evaluated in order to review the licensing for CFVS. Finally, analyses of aerosols, fission product, and radioactive material

Modulation of active pharmaceutical material release from a novel 'tablet in capsule system' containing an effervescent blend.

Science.gov (United States)

Gohel, Mukesh C; Sumitra G, Manhapra

2002-02-19

The objective of the present study was to obtain programmed drug delivery from hard gelatin capsules containing a hydrophilic plug (HPMC or guar gum). The significance of factors such as type of plug (powder or tablet), plug thickness and the formulation of fill material on the release pattern of diltiazem HCl, a model drug, was investigated. The body portion of the hard gelatin capsules was cross-linked by the combined effect of formaldehyde and heat treatment. A linear relationship was observed between weight of HPMC K15M and log % drug released at 4 h from the capsules containing the plug in powder form. In order to accelerate the drug release after a lag time of 4 h, addition of an effervescent blend, NaHCO(3) and citric acid, in the capsules was found to be essential. The plugs of HPMC in tablet form, with or without a water soluble adjuvant (NaCl or lactose) were used for obtaining immediate drug release after the lag time. Sodium chloride did not cause significant influence on drug release whereas lactose favourably affected the drug release. The capsules containing HPMC K15M tablet plug (200 mg) and 35 mg effervescent blend in body portion of the capsule met the selection criteria of less than 10% drug release in 4 h and immediate drug release thereafter. It is further shown that the drug release was also dependant on the type of swellable hydrophilic agent (HPMC or guar gum) and molecular weight of HPMC (K15M or 20 cPs). The results reveal that programmed drug delivery can be obtained from hard gelatin capsules by systemic formulation approach.

Packaging material and flexible medical tubing containing thermally exfoliated graphite oxide

Science.gov (United States)

Prud'homme, Robert K. (Inventor); Aksay, Ilhan A. (Inventor)

2011-01-01

A packaging material or flexible medical tubing containing a modified graphite oxide material, which is a thermally exfoliated graphite oxide with a surface area of from about 300 m.sup.2/g to 2600 m.sup.2/g.

Methods of pretreating comminuted cellulosic material with carbonate-containing solutions

Energy Technology Data Exchange (ETDEWEB)

Francis, Raymond

2012-11-06

Methods of pretreating comminuted cellulosic material with an acidic solution and then a carbonate-containing solution to produce a pretreated cellulosic material are provided. The pretreated material may then be further treated in a pulping process, for example, a soda-anthraquinone pulping process, to produce a cellulose pulp. The pretreatment solutions may be extracted from the pretreated cellulose material and selectively re-used, for example, with acid or alkali addition, for the pretreatment solutions. The resulting cellulose pulp is characterized by having reduced lignin content and increased yield compared to prior art treatment processes.

Understanding aging in containment cooling systems

International Nuclear Information System (INIS)

Lofaro, R.J.

1993-01-01

A study has been performed to assess the effects of aging in nuclear power plant containment cooling systems. Failure records from national databases, as well as plant specific data were reviewed and analyzed to identify aging characteristics for this system. The predominant aging mechanisms were determined, along with the most frequently failed components and their associated failure modes. This paper discusses the aging mechanisms present in the containment spray system and the containment fan cooler system, which are two systems used to provide the containment cooling function. The failure modes, along with the relative frequency of each is also discussed

Development of Latent Heat Storage Phase Change Material Containing Plaster

Directory of Open Access Journals (Sweden)

Diana BAJARE

2016-05-01

Full Text Available This paper reviews the development of latent heat storage Phase Change Material (PCM containing plaster as in passive application. Due to the phase change, these materials can store higher amounts of thermal energy than traditional building materials and can be used to add thermal inertia to lightweight constructions. It was shown that the use of PCMs have advantages stabilizing the room temperature variations during summer days, provided sufficient night ventilation is allowed. Another advantage of PCM usage is stabilized indoor temperature on the heating season. The goal of this study is to develop cement and lime based plaster containing microencapsulated PCM. The plaster is expected to be used for passive indoor applications and enhance the thermal properties of building envelope. The plaster was investigated under Scanning Electron Microscope and the mechanical, physical and thermal properties of created plaster samples were determined.

Leaching assessment of road materials containing primary lead and zinc slags.

Science.gov (United States)

Barna, R; Moszkowicz, P; Gervais, C

2004-01-01

Characterisation of the leaching behaviour of waste-containing materials is a crucial step in the environmental assessment for reuse scenarios. In our research we applied the multi-step European methodology ENV 12-920 to the leaching assessment of road materials containing metallurgical slag. A Zn slag from an imperial smelting furnace (ISF) and a Pb slag from a lead blast furnace (LBF) are investigated. The two slags contain up to 11.2 wt% of lead and 3.5 wt% of zinc and were introduced as a partial substitute for sand in two road materials, namely sand-cement and sand-bitumen. At the laboratory scale, a leaching assessment was performed first through batch equilibrium leaching tests. Second, the release rate of the contaminants was evaluated using saturated leaching tests on monolithic material. Third, laboratory tests were conducted on monolithic samples under intermittent wetting conditions. Pilot-scale tests were conducted for field testing of intermittent wetting conditions. The results show that the release of Pb and Zn from the materials in a saturated scenario was controlled by the pH of the leachates. For the intermittent wetting conditions, an additional factor, blocking of the pores by precipitation during the drying phase is proposed. Pilot-scale leaching behaviour only partially matched with the laboratory-scale test results: new mass transfer mechanisms and adapted laboratory leaching tests are discussed.

Robotic Materials Handling in Space: Mechanical Design of the Robot Operated Materials Processing System HitchHiker Experiment

Science.gov (United States)

Voellmer, George

1997-01-01

The Goddard Space Flight Center has developed the Robot Operated Materials Processing System (ROMPS) that flew aboard STS-64 in September, 1994. The ROMPS robot transported pallets containing wafers of different materials from their storage racks to a furnace for thermal processing. A system of tapered guides and compliant springs was designed to deal with the potential misalignments. The robot and all the sample pallets were locked down for launch and landing. The design of the passive lockdown system, and the interplay between it and the alignment system are presented.

Photometric determination of yttrium in zirconium-containing materials

International Nuclear Information System (INIS)

Barbina, T.M.; Polezhaev, Yu.M.

1984-01-01

Comparative evaluation of the effect of different ways of eliminating the zirconium interfering effect on the results of yttrium photometric determination with arsenazo 2 in artificial mixtures of Y 2 O 3 and ZrO 2 , containing 5 and 10 mol.% Y 2 O 3 , has been carried out. The effect of Zr is eliminated by means of its precipitation by ammonium solution in the form of hydroxide and using camouflaging with 25% sulfosalicylic acid. Both ways do not provide a correct enough result. The use of non-reagent thermohydrolytic Zr precipitation during the analysis of zirconium-containing materials permits to obtain correct and well-reproducible results

Incorporation of an item/material attribute system into PAMTRAK

International Nuclear Information System (INIS)

Anspach, D.A.; Waddoups, I.G.; Fox, E.T.

1994-01-01

The Department of Energy (DOE) mission is changing due to the number of nuclear weapon reductions by the United States and the former Soviet Union with long-term storage requirements for DOE sites increasing. New technology to ensure the integrity of special nuclear material (SNM) in storage is available to sites to supplement manual physical inventories. This allows them to decrease operating costs while keeping radiation exposure at minimal levels. We have developed a generic, real time, personnel tracking and material monitoring system named PAMTRAK. Such a system can significantly reduce the number of required, manual physical inventories at DOE sites while increasing assurance that an insider has not diverted or stolen material. Until recently Pamtrak used only material monitoring devices that provided location/containment attributes. However, Westinghouse Electric Corp. and Metrox, Inc. have recently developed hard-wired item/material attribute systems that monitor both temperature and weight. We have incorporated both of these systems into PAMTRAK. If a site employed one of these item/material attribute systems, it could decrease its manual inventory frequency to three years. This paper describes how a site might implement such a system to meet the DOE's requirements

16 CFR 1145.2 - Paint (and other similar surface-coating materials) containing lead; toys, children's articles...

Science.gov (United States)

2010-01-01

... materials) containing lead; toys, children's articles, and articles of furniture bearing such paint (or... materials) containing lead; toys, children's articles, and articles of furniture bearing such paint (or...) Paint and other similar surface-coating materials containing lead and toys, children's articles, and...

Reduction of Noise from Disc Brake Systems Using Composite Friction Materials Containing Thermoplastic Elastomers (TPEs)

Science.gov (United States)

Masoomi, Mohsen; Katbab, Ali Asghar; Nazockdast, Hossein

2006-09-01

Attempts have been made for the first time to prepare a friction material with the characteristic of thermal sensitive modulus, by the inclusion of thermoplastic elastomers (TPE) as viscoelastic polymeric materials into the formulation in order to the increase the damping behavior of the cured friction material. Styrene butadiene styrene (SBS), styrene ethylene butylene styrene (SEBS) and nitrile rubber/polyvinyl chloride (NBR/PVC) blend system were used as TPE materials. In order to evaluate the viscoelastic parameters such as loss factor (tan δ) and storage modulus (E‧) for the friction material, dynamic mechanical analyzer (DMA) were used. Natural frequencies and mode shapes of friction material and brake disc were determined by modal analysis. However, NBR/PVC and SEBS were found to be much more effective in damping behavior. The results from this comparative study suggest that the damping characteristics of commercial friction materials can be strongly affected by the TPE ingredients. This investigation also confirmed that the specimens with high TPE content had low noise propensity.

Automated nuclear material recovery and decontamination of large steel dynamic experiment containers

International Nuclear Information System (INIS)

Dennison, D.K.; Gallant, D.A.; Nelson, D.C.; Stovall, L.A.; Wedman, D.E.

1999-01-01

A key mission of the Los Alamos National Laboratory (LANL) is to reduce the global nuclear danger through stockpile stewardship efforts that ensure the safety and reliability of nuclear weapons. In support of this mission LANL performs dynamic experiments on special nuclear materials (SNM) within large steel containers. Once these experiments are complete, these containers must be processed to recover residual SNM and to decontaminate the containers to below low level waste (LLW) disposal limits which are much less restrictive for disposal purposes than transuranic (TRU) waste limits. The purpose of this paper is to describe automation efforts being developed by LANL for improving the efficiency, increasing worker safety, and reducing worker exposure during the material cleanout and recovery activities performed on these containers

Container materials in environments of corroded spent nuclear fuel

Science.gov (United States)

Huang, F. H.

1996-07-01

Efforts to remove corroded uranium metal fuel from the K Basins wet storage to long-term dry storage are underway. The multi-canister overpack (MCO) is used to load spent nuclear fuel for vacuum drying, staging, and hot conditioning; it will be used for interim dry storage until final disposition options are developed. Drying and conditioning of the corroded fuel will minimize the possibility of gas pressurization and runaway oxidation. During all phases of operations the MCO is subjected to radiation, temperature and pressure excursions, hydrogen, potential pyrophoric hazard, and corrosive environments. Material selection for the MCO applications is clearly vital for safe and efficient long-term interim storage. Austenitic stainless steels (SS) such as 304L SS or 316L SS appear to be suitable for the MCO. Of the two, Type 304L SS is recommended because it possesses good resistance to chemical corrosion, hydrogen embrittlement, and radiation-induced corrosive species. In addition, the material has adequate strength and ductility to withstand pressure and impact loading so that the containment boundary of the container is maintained under accident conditions without releasing radioactive materials.

Los Alamos National Laboratory new generation standard nuclear material storage container - the SAVY4000 design

International Nuclear Information System (INIS)

Stone, Timothy Amos

2010-01-01

Incidents involving release of nuclear materials stored in containers of convenience such as food pack cans, slip lid taped cans, paint cans, etc. has resulted in defense board concerns over the lack of prescriptive performance requirements for interim storage of nuclear materials. Los Alamos National Laboratory (LANL) has shared in these incidents and in response proactively moved into developing a performance based standard involving storage of nuclear material (RD003). This RD003 requirements document has sense been updated to reflect requirements as identified with recently issued DOE M 441.1-1 'Nuclear Material Packaging Manual'. The new packaging manual was issued at the encouragement of the Defense Nuclear Facilities Safety Board with a clear directive for protecting the worker from exposure due to loss of containment of stored materials. The Manual specifies a detailed and all inclusive approach to achieve a high level of protection; from package design and performance requirements, design life determinations of limited life components, authorized contents evaluations, and surveillance/maintenance to ensure in use package integrity over time. Materials in scope involve those stored outside an approved engineered-contamination barrier that would result in a worker exposure of in excess of 5 rem Committed Effective Does Equivalent (CEDE). Key aspects of meeting the challenge as developed around the SAVY-3000 vented storage container design will be discussed. Design performance and acceptance criteria against the manual, bounding conditions as established that the user must ensure are met to authorize contents in the package (based upon the activity of heat-source plutonium (90% Pu-238) oxide, which bounds the requirements for weapons-grade plutonium oxide), interface as a safety class system within the facility under the LANL plutonium facility DSA, design life determinations for limited life components, and a sense of design specific surveillance program

Self-contained microfluidic systems: a review.

Science.gov (United States)

Boyd-Moss, Mitchell; Baratchi, Sara; Di Venere, Martina; Khoshmanesh, Khashayar

2016-08-16

Microfluidic systems enable rapid diagnosis, screening and monitoring of diseases and health conditions using small amounts of biological samples and reagents. Despite these remarkable features, conventional microfluidic systems rely on bulky expensive external equipment, which hinders their utility as powerful analysis tools outside of research laboratories. 'Self-contained' microfluidic systems, which contain all necessary components to facilitate a complete assay, have been developed to address this limitation. In this review, we provide an in-depth overview of self-contained microfluidic systems. We categorise these systems based on their operating mechanisms into three major groups: passive, hand-powered and active. Several examples are provided to discuss the structure, capabilities and shortcomings of each group. In particular, we discuss the self-contained microfluidic systems enabled by active mechanisms, due to their unique capability for running multi-step and highly controllable diagnostic assays. Integration of self-contained microfluidic systems with the image acquisition and processing capabilities of smartphones, especially those equipped with accessory optical components, enables highly sensitive and quantitative assays, which are discussed. Finally, the future trends and possible solutions to expand the versatility of self-contained, stand-alone microfluidic platforms are outlined.

Glovebox-contained forty-millimeter gun system for the study of one-dimensional shock waves in toxic materials

International Nuclear Information System (INIS)

Honodel, C.A.

1975-01-01

A new gun system is being constructed at the Lawrence Livermore Laboratory for studies of the behavior of toxic materials under shock-loaded conditions. Due to the extreme toxicity of some materials, such as plutonium, the entire gun system must be enclosed in gloveboxes. Some of the experimental requirements that affected the design of the system, various diagnostic techniques that will be employed with the system, and some details of the final design that is presently under assembly are presented

To the problem of structural materials serviceability in nitrogen-hydrogen-containing environments

International Nuclear Information System (INIS)

Bichuya, A.L.

1982-01-01

The analysis of the factors which affect high-temperature serviceability of structural materials in nitrogen-hydrogen-containing environments, in particular in ammonia, has been carried out on the basis of the published and own experimental data. It is shown that the observed reduction of serviceability of structural materials, under the effect of high temperatures and nitrogen-hydrogen-containing environments, can occur as a result of corrosion failure connected with nitriding, and also hydrogen embrittlement appearing as a result of the penetration of hydrogen formed during adsorbed gaseous phase dissociation on the metal being deformed. The suggested scheme of high-temperature metal fracture under the effect of nitrogen-hydrogen-containing environments, that in contrast to the previous ones includes the factor of hydrogen ebrittlement, allows to give a real estimation of structional materials serviceability under product service conditions

Simulated Leaching (Migration) Study for a Model Container-Closure System Applicable to Parenteral and Ophthalmic Drug Products.

Science.gov (United States)

Jenke, Dennis; Egert, Thomas; Hendricker, Alan; Castner, James; Feinberg, Tom; Houston, Christopher; Hunt, Desmond G; Lynch, Michael; Nicholas, Kumudini; Norwood, Daniel L; Paskiet, Diane; Ruberto, Michael; Smith, Edward J; Holcomb, Frank; Markovic, Ingrid

2017-01-01

A simulating leaching (migration) study was performed on a model container-closure system relevant to parenteral and ophthalmic drug products. This container-closure system consisted of a linear low-density polyethylene bottle (primary container), a polypropylene cap and an elastomeric cap liner (closure), an adhesive label (labeling), and a foil overpouch (secondary container). The bottles were filled with simulating solvents (aqueous salt/acid mixture at pH 2.5, aqueous buffer at pH 9.5, and 1/1 v/v isopropanol/water), a label was affixed to the filled and capped bottles, the filled bottles were placed into the foil overpouch, and the filled and pouched units were stored either upright or inverted for up to 6 months at 40 °C. After storage, the leaching solutions were tested for leached substances using multiple complementary analytical techniques to address volatile, semi-volatile, and non-volatile organic and inorganic extractables as potential leachables.The leaching data generated supported several conclusions, including that (1) the extractables (leachables) profile revealed by a simulating leaching study can qualitatively be correlated with compositional information for materials of construction, (2) the chemical nature of both the extracting medium and the individual extractables (leachables) can markedly affect the resulting profile, and (3) while direct contact between a drug product and a system's material of construction may exacerbate the leaching of substances from that material by the drug product, direct contact is not a prerequisite for migration and leaching to occur. LAY ABSTRACT: The migration of container-related extractables from a model pharmaceutical container-closure system and into simulated drug product solutions was studied, focusing on circumstances relevant to parenteral and ophthalmic drug products. The model system was constructed specifically to address the migration of extractables from labels applied to the outside of the

POLYMER COMPOSITES MODIFIED BY WASTE MATERIALS CONTAINING WOOD FIBRES

Directory of Open Access Journals (Sweden)

Bernardeta Dębska

2016-11-01

Full Text Available In recent years, the idea of sustainable development has become one of the most important require-ments of civilization. Development of sustainable construction involves the need for the introduction of innovative technologies and solutions that will combine beneficial economic effects with taking care of the health and comfort of users, reducing the negative impact of the materials on the environment. Composites obtained from the use of waste materials are part of these assumptions. These include modified epoxy mortar containing waste wood fibres, described in this article. The modification consists in the substitution of sand by crushed waste boards, previously used as underlays for panels, in quantities of 0%, 10%, 20%, 35% and 50% by weight, respectively. Composites containing up to 20% of the modifier which were characterized by low water absorption, and good mechanical properties, also retained them after the process of cyclic freezing and thawing.

Proposed development programme for a temporary containment system for alpha active decommissioning

International Nuclear Information System (INIS)

Pengelly, M.G.A.; Burnett, R.C.

1983-06-01

This report makes a proposal to design, develop and test a containment of modular construction under plutonium active conditions. While this proposal contemplates work with plutonium, the system, when fully developed, has obvious applications wherever a temporary containment of radioactive or toxic materials is required. The fundamental feature of the proposal is that strippable coatings are used to prevent the inner surfaces of the working area from becoming contaminated. It is envisaged that this method of protecting the surfaces will enable the modular containment structure to be disassembled and re-used. (author)

Effect of long-lived containers on the postclosure performance of a reference disposal system

International Nuclear Information System (INIS)

Goodwin, B.W.; Hajas, W.C.; LeNeveu, D.M.

1996-05-01

The concept for disposal of Canada's nuclear fuel waste involves isolating the waste in corrosion-resistant containers emplaced in a scaled vault at a depth of 500 to 1000 m in plutonic rock of the Canadian Shield. The concept permits a choice of methods, materials, site locations, and designs. The technical feasibility of this concept and its impact on the environment and human health are summarized in an Environmental Impact Statement (AECL 1994a,b), supported by nine detailed reference documents (Davis et al. 1993; Davison et al. 1994a,b; Goodwin et al. 1994; Greber et al. 1994; Grondin et al. 1994; Johnson et al. 1994a,b; Simmons and Baumgartner 1994). In the assessment of the reference disposal system, we assumed the containers encapsulating the nuclear fuel waste were constructed from Grade-2 titanium. In this report, we investigate the effect of a different choice, and assume the use of long-lived containers constructed from materials such as high-purity copper or Grades-12 or -16 titanium alloys. These alternative materials would provide much longer periods of protection, based on the expectation that the only container failure mechanism, for times up to 10 5 a, involves initial fabrication defects. We explore the effects of long-lived containers for the same vault layout and orientation that were assumed for the reference disposal vault. We also explore effects for two less favourable situations, in which the vault is closer to a nearby fracture zone and in which the vault is extended to have emplacement rooms on both sides of the fracture zone. Our analyses use the probabilistic assessment computer code, SYVAC3-CC3, an acronym for SYstems Variability Analysis Code, generation 3. with a system model describing the Canadian Concept, generation 3, for the disposal of nuclear fuel waste. The input data for the code have been adjusted to approximate the expected protection characteristics of alternative container materials. (author). 31 refs., 1 tab., 16 figs

Corrosion behaviour of container materials for geological disposal of high level radioactive waste

International Nuclear Information System (INIS)

Accary, A.

1985-01-01

The disposal of high level radioactive waste in geological formations, based on the multibarrier concept, may include the use of a container as one of the engineered barriers. In this report the requirements imposed on this container and the possible degradation processes are reviewed. Further on an overview is given of the research being carried out by various research centres in the European Community on the assessment of the corrosion behaviour of candidate container materials. The results obtained on a number of materials under various testing conditions are summarized and evaluated. As a result, three promising materials have been selected for a detailed joint testing programme. It concerns two highly corrosion resistant alloys, resp. Ti-Pd (0.2 Pd%) and Hastelloy C4 and one consumable material namely a low carbon steel. Finally the possibilities of modelling the corrosion phenomena are discussed

Radiation exposure by man-modified materials containing natural radionuclides

Energy Technology Data Exchange (ETDEWEB)

Becker, D.E. [Technical Inspection Agency of Bavaria, Munich (Germany); Eder, E. [Government of Bavaria, Ministry for State Development and Environmental Affairs Development, Munich (Germany); Reichelt, A. [Technical Inspection Agency of Bavaria, Munich (Germany)

1992-07-01

More than one hundred materials, containing natural radioactive nuclides, are being investigated due to radiation exposure to people. This paper deals with thoriated gas mantles and shows that the radiation exposure by inhalation of radionuclides released while burning and exchange is not negligible. (author)

The development and testing of a modular containment system under plutonium active conditions

International Nuclear Information System (INIS)

Sanders, M.J.; Pengelly, M.G.A.

1984-05-01

A Modular Containment System has been designed, constructed and tested under plutonium active conditions at AEE Winfrith. The unit consists of a portable self-contained pressurised suit area, complete with shower entry tunnel and ventilation plant which can be assembled to enclose active plant to enable active operations to be carried out safely by operators dressed in standard pressurised suits. A fundamental feature of the system is the use of strippable coatings which are used to treat the interior surfaces prior to active operations to prevent permanent contamination of the structure. Details of construction are given together with results of trials. Whilst this report describes work with plutonium, the system has clear applications wherever temporary containment of radioactive or toxic materials is needed. (U.K.)

Radioactive material transporting container

International Nuclear Information System (INIS)

Watabe, Yukio.

1990-01-01

As a supporting member of a sealing container for containing spent fuels, etc., a straight pipe or a cylinder has been used. However, upon dropping test, the supporting member is buckled toward the central axis of a transporting container and a shock absorber is crushed in the axial direction to prevent its pushing force to the outer side, which may possibly hinder normal shock moderating function. Then, at least more than one-half of the supporting member is protruded radially to the outer side of the sealing container beyond the fixed portion with the sealed container, so that the member has a portion extended in the radial outside of the transporting container with an angle greater than the angle formed between a line connecting the outer circumference at the bottom of an outer cylinder with the gravitational center of the transporting container and the central axis of the transporting container. As a result, buckling of the supporting member toward the central axis of the transporting container upon dropping test can be prevented and the deformation of the shock absorber is neither not prevented to exhibit normal shock absorbing effect. This can improve the reliability and reduce the amount of shock absorbers. (N.H.)

Containers for short-term storage of nuclear materials at the Los Alamos plutonium facility

International Nuclear Information System (INIS)

Hagan, R.; Gladson, J.

1997-01-01

The Los Alamos Plutonium Facility for the past 18 yr has stored nuclear samples for archiving and in support of nuclear materials research and processing programs. In the past several years, a small number of storage containers have been found in a deteriorated condition. A failed plutonium container can cause personnel contamination exposure and expensive physical area decontamination. Containers are stored in a physically secure radiation area vault, making close inspection costly in the form of personnel radiation exposure and work time. A moderate number of these containers are used in support of plutonium processing and must withstand daily handling abuse. A 2-yr evaluation of failed containers and those that have shown no deterioration has been conducted. Based on that study, a program was established to formalize our packing methods and materials and standardize the size and shape of containers that are used for short-term use. A standardized set of containers was designed, evaluated, tested, and procured for use in the facility. This paper reviews our vault storage problems, shows some failed containers, and presents our planned solutions to provide safe and secure containment of nuclear materials

MULCHES AND OTHER COVER MATERIALS TO REDUCE WEED GROWTH IN CONTAINER-GROWN NURSERY STOCK.

Science.gov (United States)

Rys, F; Van Wesemael, D; Van Haecke, D; Mechant, E; Gobin, B

2014-01-01

Due to the recent EU-wide implementation of Integrated Pest Management (IPM), alternative methods to reduce weed growth in container-grown nursery stock are needed to cut back the use of herbicides. Covering the upper layer of the substrate is known as a potential method to prevent or reduce weed growth in plant containers. As a high variety of mulches and other cover materials are on the market, however, it is no longer clear for growers which cover material is most efficient for use in containers. Therefore, we examined the effect on weed growth of different mulches and other cover materials, including Pinus maritima, P. sylvestris, Bio-Top Basic, Bio-Top Excellent, coco chips fine, hemp fibres, straw pellets, coco disk 180LD and jute disk. Cover materials were applied immediately after repotting of Ligustrum ovalifolium or planting of Fagus sylvatica. At regular times, both weed growth and side effects (e.g., plant growth, water status of the substrate, occurrence of mushrooms, foraging of birds, complete cover of the substrate and fixation) were assessed. All examined mulches or other cover materials were able to reduce weed growth on the containers during the whole growing season. Weed suppression was even better than that of a chemical treated control. Although all materials showed some side effects, the impact on plant growth is most important to the grower and depends not only on material characteristics (e.g., biodegradation, nutrient leaching and N-immobilisation) but also on container size and climatic conditions. In conclusion, mulches and other cover materials can be a valuable tool within IPM to lower herbicide use. To enable a deliberate choice of which cover material is best used in a specific situation more research is needed on lifespan and stability as well as on economic characteristics of the materials.

Enviro-geotechnical considerations in waste containment system design and analysis

International Nuclear Information System (INIS)

Fang, H.Y.; Daniels, J.L.; Inyang, H.I.

1997-01-01

The effectiveness of waste control facilities hinges on careful evaluation of the overall planning, analysis and design of the entire system prior to construction. At present, most work is focused on the waste controlling system itself, with little attention given to the local environmental factors surrounding the facility sites. Containment materials including geomembranes, geotextiles and clay amended soils have received intense scrutiny. This paper, however, focuses on three relatively important issues relating to the characterization of the surrounding geomedia. Leakage through naturally occurring low-permeability soil layers, shrinkages swelling, cracking and effects of dynamic loads on system components are often responsible for a waste containment breach. In this paper, these mechanisms and their synergistic effects are explained in terms of the particle energy field theory. It is hoped that this additional information may assist the designer to be aware or take precaution to design safer future waste control facilities

Material Systems

DEFF Research Database (Denmark)

Jensen, Mads Brath; Mortensen, Henrik Rubæk; Mullins, Michael

2009-01-01

This paper describes and reflects upon the results of an investigative project which explores the setting up of a material system - a parametric and generative assembly consisting of and taking into consideration material properties, manufacturing constraints and geometric behavior. The project...... approaches the subject through the construction of a logic-driven system aiming to explore the possibilities of a material system that fulfills spatial, structural and performative requirements concurrently and how these are negotiated in situations where they might be conflicting....

Membrane and Films Based on Novel Crown-Containing Dyes as Promising Chemosensoring Materials

Directory of Open Access Journals (Sweden)

Sergei Yu. Zaitsev

2010-12-01

Full Text Available This paper discusses several works on supramolecular systems such as monolayer and multilayer, polymer films of various crown-containing dyes, surface-active monomers and polymers. Design, production and investigation of the membrane nanostructures based on crown ethers is a rapidly developing field at the “junction” of materials sciences and nanotechnology. These nanostructures can serve as convenient models for studying the self-organization and molecular recognition processes at interfaces that are typical for biomembranes. Based on the results obtained for such structures by absorption and fluorescence spectroscopy, atomic force and Brewster-angle microscopy, surface pressure and surface potential isotherm measurements, the possibility of developing micro- and nanomaterials possessing a set of specified properties (including chemosensor, photochromic and photorefractive materials is demonstrated.

Fluorine uptake into the human enamel surface from fluoride-containing sealing materials during cariogenic pH cycling

Energy Technology Data Exchange (ETDEWEB)

Yasuhiro, Matsuda, E-mail: matsuda@den.hokudai.ac.jp [Department of Restorative Dentistry, Graduate School of Dental Medicine Hokkaido University (Japan); Katsushi, Okuyama [Department of Restorative Dentistry, Graduate School of Dental Medicine Hokkaido University (Japan); Hiroko, Yamamoto [Graduate School of Dentistry, Osaka University (Japan); Hisanori, Komatsu [Department of Restorative Dentistry, Graduate School of Dental Medicine Hokkaido University (Japan); Masashi, Koka; Takahiro, Sato [Takasaki Advanced Radiation Research Institute, JAEA (Japan); Naoki, Hashimoto; Saiko, Oki; Chiharu, Kawamoto; Hidehiko, Sano [Department of Restorative Dentistry, Graduate School of Dental Medicine Hokkaido University (Japan)

2015-04-01

To prevent the formation of caries and reduce dentin hypersensitivity, sealing materials, either with or without fluoride, are generally applied on the tooth in clinical practice. Application of fluoride-free sealing materials results in the formation of an acid-resistant layer on the tooth surface. On the other hand, fluoride-containing sealing materials might not only form an acid-resistant layer but could possibly further provide fluoride to enhance remineralization and reduce demineralization. In this study, the demineralization prevention ability and fluorine uptake rate in human enamel of fluoride-containing sealing materials [“MS coats F” (MSF)] and fluoride-free sealing materials (“hybrid coats 2” [HI]) were evaluated using an automatic pH cycling system. Each material was applied to the original tooth surface, the cut surfaces were covered with sticky wax, and the automatic pH-cycling system simulated daily acid changes (pH 6.8–4.5) occurring in the oral cavity for 4 weeks. Caries progression was analyzed using transverse microradiography (TMR) taken pre and post the 4 weeks of pH cycling. The fluorine and calcium distributions in the carious lesion in each specimen were evaluated using the proton-induced gamma emission (PIGE) and proton-induced X-ray (PIXE) techniques, respectively. TMR analysis showed that both MSF and HI had a caries-preventing effect after 4 weeks of pH cycling. PIGE/PIXE analysis demonstrated that only MSF resulted in fluoride uptake in the enamel surface. Therefore, MSF can help to form an acid-resistant layer and provide fluoride to the enamel surface. The presence of fluoride on the enamel surface suggested that MSF could prevent demineralization, even if the acid-resistant layer was removed, in clinical settings. The data obtained using the PIGE and PIXE techniques are useful for understanding the benefits of the use of a fluoride-containing sealing material for preventing caries.

Fluorine uptake into the human enamel surface from fluoride-containing sealing materials during cariogenic pH cycling

International Nuclear Information System (INIS)

Yasuhiro, Matsuda; Katsushi, Okuyama; Hiroko, Yamamoto; Hisanori, Komatsu; Masashi, Koka; Takahiro, Sato; Naoki, Hashimoto; Saiko, Oki; Chiharu, Kawamoto; Hidehiko, Sano

2015-01-01

To prevent the formation of caries and reduce dentin hypersensitivity, sealing materials, either with or without fluoride, are generally applied on the tooth in clinical practice. Application of fluoride-free sealing materials results in the formation of an acid-resistant layer on the tooth surface. On the other hand, fluoride-containing sealing materials might not only form an acid-resistant layer but could possibly further provide fluoride to enhance remineralization and reduce demineralization. In this study, the demineralization prevention ability and fluorine uptake rate in human enamel of fluoride-containing sealing materials [“MS coats F” (MSF)] and fluoride-free sealing materials (“hybrid coats 2” [HI]) were evaluated using an automatic pH cycling system. Each material was applied to the original tooth surface, the cut surfaces were covered with sticky wax, and the automatic pH-cycling system simulated daily acid changes (pH 6.8–4.5) occurring in the oral cavity for 4 weeks. Caries progression was analyzed using transverse microradiography (TMR) taken pre and post the 4 weeks of pH cycling. The fluorine and calcium distributions in the carious lesion in each specimen were evaluated using the proton-induced gamma emission (PIGE) and proton-induced X-ray (PIXE) techniques, respectively. TMR analysis showed that both MSF and HI had a caries-preventing effect after 4 weeks of pH cycling. PIGE/PIXE analysis demonstrated that only MSF resulted in fluoride uptake in the enamel surface. Therefore, MSF can help to form an acid-resistant layer and provide fluoride to the enamel surface. The presence of fluoride on the enamel surface suggested that MSF could prevent demineralization, even if the acid-resistant layer was removed, in clinical settings. The data obtained using the PIGE and PIXE techniques are useful for understanding the benefits of the use of a fluoride-containing sealing material for preventing caries

Materials handbook for fusion energy systems

International Nuclear Information System (INIS)

Davis, J.W.

1988-01-01

The objective of this work is to provide a consistent and authoritative source of material property data for use by the fusion community in concept evaluation, design, and performance/verification studies of the various fusion energy systems. A second objective is the early identification of areas in the materials data base where insufficient information or voids exist. The effort during this reporting period has focused on two areas: (1) publication of data pages, and (2) automation of the data pages. The data pages contained new engineering information on lithium and stainless steel along with additional Supporting Documentation pages on annealed and cold worked stainless steel. These pages were distributed in May. In the area of automation, work is proceeding on schedule toward the formation of an electronic materials data base for the MFE computer network

Radioactive material-containing vessel and method of manufacturing the same

International Nuclear Information System (INIS)

Kanazawa, Hiroshi; Wada, Katsuyoshi; Ota, Shigeo; Nishioka, Eiji; Okuno, Michinori.

1995-01-01

In a vessel for containing radioactive materials having an outer wall with a structure of interposing a lead layer, as a shielding material between inner and outer cylinders made of steel plates, the inner cylinder and the lead layer are in close contact by way of a thin layer of a lead/tin type soldering material and to such an extent that the boundary layer is not detected by supersonic inspection. In addition, flux is coated to the steel plate, which forms the inner cylinder, on the surface being in contact with the lead layer, then a thin layer of the soldering material such as lead or tin is formed, to cast the lead between the inner and the outer cylinders. Then, since the inner cylinder and the lead layer are thermally joined tightly, heat generated at the inside can effectively be released to the outside, so that it is effective as a high-performance cask for transporting a large amount of radioactive materials such as spent nuclear fuels having high temperature afterheat. In addition, a containing vessel with good contact between the inner cylinder and the lead can be manufactured at a low cost only applying a simple primer treatment on the surface of the inner cylinder in addition to an existent lead casting method. (N.H.)

Sodium montmorillonite/amine-containing drugs complexes: new insights on intercalated drugs arrangement into layered carrier material.

Directory of Open Access Journals (Sweden)

Murilo L Bello

Full Text Available Layered drug delivery carriers are current targets of nanotechnology studies since they are able to accommodate pharmacologically active substances and are effective at modulating drug release. Sodium montmorillonite (Na-MMT is a clay that has suitable properties for developing new pharmaceutical materials due to its high degree of surface area and high capacity for cation exchange. Therefore Na-MMT is a versatile material for the preparation of new drug delivery systems, especially for slow release of protonable drugs. Herein, we describe the intercalation of several amine-containing drugs with Na-MMT so we can derive a better understanding of how these drugs molecules interact with and distribute throughout the Na-MMT interlayer space. Therefore, for this purpose nine sodium montmorillonite/amine-containing drugs complexes (Na-MMT/drug were prepared and characterized. In addition, the physicochemical properties of the drugs molecules in combination with different experimental conditions were assessed to determine how these factors influenced experimental outcomes (e.g. increase of the interlayer spacing versus drugs arrangement and orientation. We also performed a molecular modeling study of these amine-containing drugs associated with different Na-MMT/drug complex models to analyze the orientation and arrangement of the drugs molecules in the complexes studied. Six amine-containing drugs (rivastigmine, doxazosin, 5-fluorouracil, chlorhexidine, dapsone, nystatin were found to successfully intercalate Na-MMT. These findings provide important insights on the interlayer aspect of the molecular systems formed and may contribute to produce more efficient drug delivery nanosystems.

Experiments on container materials for Swiss high-level waste disposal projects. Part 2

International Nuclear Information System (INIS)

Simpson, J.P.

1984-12-01

The present concept for final disposal of high-level waste in Switzerland consists of a repository at a depth of 1000 to 1500 m in the crystalline bedrock of northern Switzerland. The waste will be placed in a container which is required to function as a high integrity barrier for at least 1000 years. This report is the second of a set of two dealing with the evaluation of potential materials for such containers. Four materials were identified for further evaluation in the first of these reports; they were cast steel, nodular cast iron, copper and Ti-Code 12. It was concluded that some testing was needed, in particular with respect to corrosion, in order to confirm these materials as candidate container materials. The experimental programme included: 1) corrosion tests on copper under gamma radiation; 2) immersion corrosion tests on the four candidate materials including welded specimens; 3) corrosion testing of the four materials in saturated bentonite; 4) constant strain rate testing of Ti-Code 12 and copper at 80 degrees C; 5) the behaviour of copper, Ti-Code 12 and Zircaloy-2 when immersed in liquid lead; 6) corrosion potential and galvanic current measurements on several material pairs. The standard test medium was natural mineral water from the Bad Saeckingen source. This water has a total dissolved solids content of approx. 3200 mg/l, about 1600 mg/l as chloride. The oxygen level was defined as 0.1 μg/g. In certain cases this medium was modified in order to test under more severe conditions. The results of the corrosion tests confirm in general the evaluation in the first part of the report. All of the materials are suitable for high-level waste containers: cast steel, nodular cast iron and copper as single layer containers, and Ti-Code 12 as an outer corrosion resistant layer. Copper could also be used under an outer steel layer, where it could arrest local penetration

Demonstration personnel and material tracking system at ANL-W

International Nuclear Information System (INIS)

Roybal, J.A.; Ortiz, S.; Henslee, S.P.

1988-01-01

A Personnel and Material Tracking System (PMTS) was demonstrated in the Fuel Manufacturing Facility (FMF) at Argonne National Laboratories-West (ANL-W) in July, 1987. The PMTS is intended to aid in the transfer of inventory materials from area to area within a facility such as FMF. It is also intended to assure that only those personnel who are authorized to do so may conduct these transfer operations. The PMTS Personnel Movement (PM) subsystem uses portals installed between areas to alert the system to the movement of personnel between areas. The portals are composed to two sensors, one on either side of a proximity badge reader, to detect the presence of personnel entering the portal area. However, a restricted area can be assigned to any badge holder which will cause the system to issue an alert if the badge holder passes into his/her restricted area. The PM subsystem is intended to be transparent when in use. The PMTS Inventory Material Access (IMA) subsystem provides two functions: material control and material access. The material control is provided by the Wireless Alarm Transmission of Container Handling (WATCH) system which is a sensor rf transmitter system that detects item movements. Material access is provided by the Mobile Accountability Verification Inventory Station (MAVIS) system which is a self-powered smart barcode reader

Direct conversion of plutonium-containing materials to borosilicate glass for storage or disposal

International Nuclear Information System (INIS)

Forsberg, C.W.; Beahm, E.C.

1995-01-01

A new process, the Glass Material Oxidation and Dissolution System (GMODS), has been invented for the direct conversion of plutonium metal, scrap, and residue into borosilicate glass. The glass should be acceptable for either the long-term storage or disposition of plutonium. Conversion of plutonium from complex chemical mixtures and variable geometries into homogeneous glass (1) simplifies safeguards and security; (2) creates a stable chemical form that meets health, safety, and environmental concerns; (3) provides an easy storage form; (4) may lower storage costs; and (5) allows for future disposition options. In the GMODS process, mixtures of metals, ceramics, organics, and amorphous solids containing plutonium are fed directly into a glass melter where they are directly converted to glass. Conventional glass melters can accept materials only in oxide form; thus, it is its ability to accept materials in multiple chemical forms that makes GMODS a unique glass making process. Initial proof-of-principle experiments have converted cerium (plutonium surrogate), uranium, stainless steel, aluminum, and other materials to glass. Significant technical uncertainties remain because of the early nature of process development

Preliminary sensitivity analyses of corrosion models for BWIP [Basalt Waste Isolation Project] container materials

International Nuclear Information System (INIS)

Anantatmula, R.P.

1984-01-01

A preliminary sensitivity analysis was performed for the corrosion models developed for Basalt Waste Isolation Project container materials. The models describe corrosion behavior of the candidate container materials (low carbon steel and Fe9Cr1Mo), in various environments that are expected in the vicinity of the waste package, by separate equations. The present sensitivity analysis yields an uncertainty in total uniform corrosion on the basis of assumed uncertainties in the parameters comprising the corrosion equations. Based on the sample scenario and the preliminary corrosion models, the uncertainty in total uniform corrosion of low carbon steel and Fe9Cr1Mo for the 1000 yr containment period are 20% and 15%, respectively. For containment periods ≥ 1000 yr, the uncertainty in corrosion during the post-closure aqueous periods controls the uncertainty in total uniform corrosion for both low carbon steel and Fe9Cr1Mo. The key parameters controlling the corrosion behavior of candidate container materials are temperature, radiation, groundwater species, etc. Tests are planned in the Basalt Waste Isolation Project containment materials test program to determine in detail the sensitivity of corrosion to these parameters. We also plan to expand the sensitivity analysis to include sensitivity coefficients and other parameters in future studies. 6 refs., 3 figs., 9 tabs

19 CFR 10.539 - Retail packaging materials and containers.

Science.gov (United States)

2010-04-01

...-Singapore Free Trade Agreement Rules of Origin § 10.539 Retail packaging materials and containers. Packaging... requirement. The United States importer of good C decides to use the build-down method, RVC=((AV−VNM)/AV... content requirement. In applying this method, the non-originating blister packages are taken into account...

Stowing of packages containing radioactive materials on conveyances

International Nuclear Information System (INIS)

Draulans, J.; Lafontaine, I.; Chevalier, G.; Gilles, P.; Jolys, J.C.; Pouard, M.

1986-04-01

The Commission of the European Communities has financed some research work carried out jointly by the ''Commissariat a l'Energie Atomique'' and the belgian company ''TRANSNUBEL'', in the field of stowing containers for radioactive materials on trucks. 2 reference type accidents are selected: . a front-end collision against a rigid barrier at an impact speed of 50 km/h . a side-on collision of an impacting vehicle at a speed of 25-35 km/h against a truck loaded with a container. A mathematical model has been developed by means of the CEA Trico code to compute a frontal impact in which the container (1.3 t weight), is stowed by means of 4 tie-down members, each for a nominal load of 2 t. Results indicate the stowing being insufficient and the attachment points too weak to keep the container on the platform. Real tests have been performed to verify these results. Tie-down members and chocks have been defined on the basis of static- and dynamic tests for being used in 8 crash tests. Different containers (low- and high center of gravity) and different ways of stowing have been tried out. An attempt is made to work a code of good practice for stowing, by means of tie-down members and chocks, packages on a truck platform. 19 refs

Database management system for large container inspection system

International Nuclear Information System (INIS)

Gao Wenhuan; Li Zheng; Kang Kejun; Song Binshan; Liu Fang

1998-01-01

Large Container Inspection System (LCIS) based on radiation imaging technology is a powerful tool for the Customs to check the contents inside a large container without opening it. The author has discussed a database application system, as a part of Signal and Image System (SIS), for the LCIS. The basic requirements analysis was done first. Then the selections of computer hardware, operating system, and database management system were made according to the technology and market products circumstance. Based on the above considerations, a database application system with central management and distributed operation features has been implemented

The ''nuclear car wash'': a scanner to detect illicit special nuclear material in cargo containers

International Nuclear Information System (INIS)

Slaughter, D. R.; Accatino, M. R.; Bernstein, A.; Dougan, A. D.; Hall, J. M.; Loshak, A.; Manatt, D. R.; Pohl, B. A.; Prussin, S. G.; Walling, R. S.; Weirup, D. L.

2004-01-01

There is an urgent need to improve the reliability of screening cargo containers for illicit nuclear material that may be hidden there for terrorist purposes. A screening system is described for detection of fissionable material hidden in maritime cargo containers. The system makes use of a low intensity neutron beam for producing fission; and the detection of the abundant high-energy γ rays emitted in the β-decay of short-lived fission products and β-delayed neutrons. The abundance of the delayed γ rays is almost an order of magnitude larger than that of the delayed neutrons normally used to detect fission and they are emitted on about the same time scale as the delayed neutrons, i.e., ∼1 min. The energy and temporal distributions of the delayed γ rays provide a unique signature of fission. Because of their high energy, these delayed γ rays penetrate loW--Z cargoes much more readily than the delayed neutrons. Coupled with their higher abundance, the signal from the delayed γ rays escaping from the container is predicted to be as much as six decades more intense than the delayed neutron signal, depending upon the type and thickness of the intervening cargo. The γ rays are detected in a large array of scintillators located along the sides of the container as it is moved through them. Measurements have confirmed the signal strength in somewhat idealized experiments and have also identified one interference when 14.5 MeV neutrons from the D, T reaction are used for the interrogation. The interference can be removed easily by the appropriate choice of the neutron source

A PROBABILISTIC METHOD FOR ESTIMATING MONITORING POINT DENSITY FOR CONTAINMENT SYSTEM LEAK DETECTION

Science.gov (United States)

The use of physical and hydraulic containment systems for the isolation of contaminated ground water and aquifer materials ssociated with hazardous waste sites has increased during the last decade. The existing methodologies for monitoring and evaluating leakage from hazardous w...

An integrated system for identifying the hidden assassins in traditional medicines containing aristolochic acids

Science.gov (United States)

Wu, Lan; Sun, Wei; Wang, Bo; Zhao, Haiyu; Li, Yaoli; Cai, Shaoqing; Xiang, Li; Zhu, Yingjie; Yao, Hui; Song, Jingyuan; Cheng, Yung-Chi; Chen, Shilin

2015-08-01

Traditional herbal medicines adulterated and contaminated with plant materials from the Aristolochiaceae family, which contain aristolochic acids (AAs), cause aristolochic acid nephropathy. Approximately 256 traditional Chinese patent medicines, containing Aristolochiaceous materials, are still being sold in Chinese markets today. In order to protect consumers from health risks due to AAs, the hidden assassins, efficient methods to differentiate Aristolochiaceous herbs from their putative substitutes need to be established. In this study, 158 Aristolochiaceous samples representing 46 species and four genera as well as 131 non-Aristolochiaceous samples representing 33 species, 20 genera and 12 families were analyzed using DNA barcodes based on the ITS2 and psbA-trnH sequences. Aristolochiaceous materials and their non-Aristolochiaceous substitutes were successfully identified using BLAST1, the nearest distance method and the neighbor-joining (NJ) tree. In addition, based on sequence information of ITS2, we developed a Real-Time PCR assay which successfully identified herbal material from the Aristolochiaceae family. Using Ultra High Performance Liquid Chromatography-Mass Spectrometer (UHPLC-HR-MS), we demonstrated that most representatives from the Aristolochiaceae family contain toxic AAs. Therefore, integrated DNA barcodes, Real-Time PCR assays using TaqMan probes and UHPLC-HR-MS system provides an efficient and reliable authentication system to protect consumers from health risks due to the hidden assassins (AAs).

Phase equilibria for mixtures containing nonionic surfactant systems: Modeling and experiments

International Nuclear Information System (INIS)

Shin, Moon Sam; Kim, Hwayong

2008-01-01

Surfactants are important materials with numerous applications in the cosmetic, pharmaceutical, and food industries due to inter-associating and intra-associating bond. We present a lattice fluid equation-of-state that combines the quasi-chemical nonrandom lattice fluid model with Veytsman statistics for (intra + inter) molecular association to calculate phase behavior for mixtures containing nonionic surfactants. We also measured binary (vapor + liquid) equilibrium data for {2-butoxyethanol (C 4 E 1 ) + n-hexane} and {2-butoxyethanol (C 4 E 1 ) + n-heptane} systems at temperatures ranging from (303.15 to 323.15) K. A static apparatus was used in this study. The presented equation-of-state correlated well with the measured and published data for mixtures containing nonionic surfactant systems

Potential containment materials for liquid-lead and lead-bismuth eutectic spallation neutron source

International Nuclear Information System (INIS)

Park, J.J.; Butt, D.P.; Beard, C.A.

1997-11-01

Lead (Pb) and lead-bismuth eutectic (44Pb-56Bi) have been the two primary candidate liquid-metal target materials for the production of spallation neutrons. Selection of a container material for the liquid-metal target will greatly affect the lifetime and safety of the target subsystem. For the lead target, niobium-1 (wt%) zirconium (Nb-1Zr) is a candidate containment material for liquid lead, but its poor oxidation resistance has been a major concern. The oxidation rate of Nb-1Zr was studied based on the calculations of thickness loss due to oxidation. According to these calculations, it appeared that uncoated Nb-1Zr may be used for a one-year operation at 900 C at P O 2 = 1 x 10 -6 torr, but the same material may not be used in argon with 5-ppm oxygen. Coating technologies to reduce the oxidation of Nb-1Zr are reviewed, as are other candidate refractory metals such as molybdenum, tantalum, and tungsten. For the Pb-Bi target, three candidate containment materials are suggested based on a literature survey of the materials compatibility and proton irradiation tests: Croloy 2-1/4, modified 9Cr-1Mo, and 12Cr-1Mo (HT-9) steel. These materials seem to be used only if the lead-bismuth is thoroughly deoxidized and treated with zirconium and magnesium

Ultrasonic Fingerprinting of Structural Materials: Spent Nuclear Fuel Containers Case-Study

Science.gov (United States)

Sednev, D.; Lider, A.; Demyanuk, D.; Kroening, M.; Salchak, Y.

Nowadays, NDT is mainly focused on safety purposes, but it seems possible to apply those methods to provide national and IAEA safeguards. The containment of spent fuel in storage casks could be dramatically improved in case of development of so-called "smart" spent fuel storage and transfer casks. Such casks would have tamper indicating and monitoring/tracking features integrated directly into the cask design. The microstructure of the containers material as well as of the dedicated weld seam is applied to the lid and the cask body and provides a unique fingerprint of the full container, which can be reproducibly scanned by using an appropriate technique. The echo-sounder technique, which is the most commonly used method for material inspection, was chosen for this project. The main measuring parameter is acoustic noise, reflected from material's artefacts. The purpose is to obtain structural fingerprinting. Reference measurement and additional measurement results were compared. Obtained results have verified the appliance of structural fingerprint and the chosen control method. The successful authentication demonstrates the levels of the feature points' compliance exceeding the given threshold which differs considerably from the percentage of the concurrent points during authentication from other points. Since reproduction or doubling of the proposed unique identification characteristics is impossible at the current state science and technology, application of this technique is considered to identify the interference into the nuclear materials displacement with high accuracy.

Positron-containing systems and positron diagnostics

International Nuclear Information System (INIS)

1978-01-01

The results of the experimental and theoretical investigations are presented. Considered are quantum-mechanical calculations of wave functions describing the states of positron-containing atomic systems and of cross-sections of the processes characterizing different interactions, and also the calculations of the behaviour of positrons in gases in the presence of an electric field. The results of experimental tests are presented by the data describing the behaviour of positrons and positronium in liquids, polymers and elastomers, complex oxides and in different solids. New equipment and systems developed on the basis of current studies are described. Examined is a possibility of applying the methods of model and effective potentials for studying the bound states of positron systems and for calculating cross-sections of elementary processes of elastic and inelastic collisions with a positron involved. The experimental works described indicate new possibilities of the positron diagnosis method: investigation of thin layers and films of semiconductor materials, defining the nature of chemical bonds in semiconductors, determination of the dislocation density in deformed semiconductors, derivation of important quantitative information of the energy states of radiation defects in them

Materials for Concentrator Photovoltaic Systems: Optical Properties and Solar Radiation Durability

Science.gov (United States)

French, R. H.; Rodríguez-Parada, J. M.; Yang, M. K.; Lemon, M. F.; Romano, E. C.; Boydell, P.

2010-10-01

Concentrator photovoltaic (CPV) systems are designed to operate over a wide range of solar concentrations, from low concentrations of ˜1 to 12 Suns to medium concentrations in the range from 12 to 200 Suns, to high concentration CPV systems going up to 2000 Suns. Many transparent optical materials are used for a wide variety of functions ranging from refractive and reflective optics to homogenizers, encapsulants and even thermal management. The classes of materials used also span a wide spectrum from hydrocarbon polymers (HCP) and fluoropolymers (FP) to silicon containing polymers and polyimides (PI). The optical properties of these materials are essential to the optical behavior of the system. At the same time radiation durability of these materials under the extremely wide range of solar concentrations is a critical performance requirement for the required lifetime of a CPV system. As part of our research on materials for CPV we are evaluating the optical properties and solar radiation durability of various polymeric materials to define the optimum material combinations for various CPV systems.

Advanced Containment System

Science.gov (United States)

Kostelnik, Kevin M.; Kawamura, Hideki; Richardson, John G.; Noda, Masaru

2004-10-12

An advanced containment system for containing buried waste and associated leachate. A trench is dug on either side of the zone of interest containing the buried waste so as to accommodate a micro tunnel boring machine. A series of small diameter tunnels are serially excavated underneath the buried waste. The tunnels are excavated by the micro tunnel boring machine at a consistent depth and are substantially parallel to each other. As tunneling progresses, steel casing sections are connected end to end in the excavated portion of the tunnel so that a steel tube is formed. Each casing section has complementary interlocking structure running its length that interlocks with complementary interlocking structure on the adjacent casing section. Thus, once the first tube is emplaced, placement of subsequent tubes is facilitated by the complementary interlocking structure on the adjacent, previously placed, casing sections.

Containment and surveillance systems for international safeguards

International Nuclear Information System (INIS)

Ney, J.F.

1978-01-01

Important criteria in measuring the effectiveness of IAEA safeguards include timeliness of detection of diversion, timeliness of reporting such detections, and confidence in determining the amount of material diverted. Optimum use of IAEA inspectors, combined with adequate instrumentation, can provide a practical means for achieving these criteria. System studies are being carried out for different types of facilities that may come under IAEA safeguards to determine the proper balance between inspector's efforts and the use of safeguards instrumentation. A description of a typical study is presented. Based on the results of these studies, the program undertaken to develop those containment and surveillance subsystems for which the technical feasibility and operational acceptability need to be established is described

Mockup of an automated material transport system for remote handling

International Nuclear Information System (INIS)

Porter, M.L.

1992-01-01

An Automated Material Transport System (AMTS) was identified for transport of samples within a Material and Process Control Laboratory (MPCL). The MPCL was designed with a dry sample handling laboratory and a wet chemistry analysis laboratory. Each laboratory contained several processing gloveboxes. The function of the AMTS was to automate the handling of materials, multiple process samples, and bulky items between process stations with a minimum of operator intervention and with minimum o[ waiting periods and nonproductive activities. This paper discusses the system design features, capabilities and results of initial testing. The overall performance of the AMTS is very good. No major problems or concerns were identified. System commands are simple and logical making the system user friendly. Operating principle and design of individual components is simple. With the addition of various track modules, the system can be configured in most any configuration. The AMTS lends itself very well for integration with other automated systems or products. The AMTS is suited for applications involving light payloads which require multiple sample and material handling, lot tracking, and system integration with other products

Reliability analysis of containment isolation systems

International Nuclear Information System (INIS)

Pelto, P.J.; Counts, C.A.

1984-06-01

The Pacific Northwest Laboratory (PNL) is reviewing available information on containment systems design, operating experience, and related research as part of a project being conducted by the Division of Systems Integration, US Nuclear Regulatory Commission. The basic objective of this work is to collect and consolidate data relevant to assessing the functional performance of containment isolation systems and to use this data to the extent possible to characterize containment isolation system reliability for selected reference designs. This paper summarizes the results from initial efforts which focused on collection of data from available documents and briefly describes detailed review and analysis efforts which commenced recently. 5 references

The Soviet RBMK-1000 containment system

International Nuclear Information System (INIS)

Joosten, J.K.

1988-01-01

Following the accident in April, 1986, considerable attention was focused on the failure of the containment at the Chernobyl RBMK-1000 nuclear power plant. Conflicting statements arose regarding the nature of the plant's containment system primarily because of terminology differences, translation difficulties and lack of reliable information. This article, based on reports and briefings by the Soviet delegation, during the post-accident review meetings in Vienna and prior publications is intended to clarify perceptions of the Soviet RMBK-1000 nuclear power plant containment system design, and its relevance to containment management concepts. (author)

49 CFR 176.170 - Transport of Class 1 (explosive) materials in freight containers.

Science.gov (United States)

2010-10-01

... 49 Transportation 2 2010-10-01 2010-10-01 false Transport of Class 1 (explosive) materials in... REGULATIONS CARRIAGE BY VESSEL Detailed Requirements for Class 1 (Explosive) Materials Cargo Transport Units and Shipborne Barges § 176.170 Transport of Class 1 (explosive) materials in freight containers. (a...

Waste handling and REACH : Recycling of materials containing SVHCs: daily practice challenges

NARCIS (Netherlands)

Janssen MPM; van Broekhuizen FA; MSP; M&V

2017-01-01

To achieve a circular economy it is essential to recycle substances, materials and products created by that economy. Recycling, however, becomes more difficult when said materials and products contain substances that are so hazardous that their use is restricted. This is the case with any substance

Development of a container for the transportation and storage of plutonium bearing materials

International Nuclear Information System (INIS)

Ammerman, D.; Geinitz, R.; Thorp, D.; Rivera, M.

1998-03-01

There is a large backlog of plutonium contaminated materials at the Rocky Flats Environmental Technology Site near Denver, Colorado, USA. The clean-up of this site requires this material to be packaged in such a way as to allow for efficient transportation to other sites or to a permanent geologic repository. Prior to off-site shipment of the material, it may be stored on-site for a period of time. For this reason, it is desirable to have a container capable of meeting the requirements for storage as well as the requirements for transportation. Most of the off-site transportation is envisioned to take place using the TRUPACT-II Type B package, with the Waste Isolation Pilot Plant (WIPP) as the destination. Prior to the development of this new container, the TRUPACT-II had a limit of 325 FGE (fissile gram equivalents) of plutonium due to criticality control concerns. Because of the relatively high plutonium content in the material to be transported, transporting 325 FGE per TRUPACT-II is uneconomical. Thus, the purpose of the new containers is to provide criticality control to increase the allowed TRUPACT-II payload and to provide a safe method for on-site storage prior to transport. This paper will describe the analysis and testing used to demonstrate that the Pipe Overpack Container provides safe on-site storage of plutonium bearing materials in unhardened buildings and provides criticality control during transportation within the TRUPACT-II. Analyses included worst-case criticality analyses, analyses of fork-lift time impacts, and analyses of roof structure collapse onto the container. Testing included dynamic crush tests, bare pipe impact tests, a 30-minute totally engulfing pool-fire test, and multiple package impact tests in end-on and side-on orientations

Experiments on container materials for Swiss high-level waste disposal projects. Part IV

International Nuclear Information System (INIS)

Simpson, J.P.

1989-12-01

One concept for final disposal of high-level waste in switzerland consists of a repository at a depth of 1000 to 1500 m in the crystalline bedrock of Northern Switzerland. The waste will be placed in a container which will be required to function as a high integrity barrier for at least 100 years. This report is the fourth and last in the current series dealing with the evaluation of potential materials for such containers. Four materials were identified for further evaluation in the first of these reports: cast steel, nodular cast iron, copper and Ti-Code 12. This report deals with the problem of demonstrating that cast steel containers will not fail by stress corrosion cracking and with the problem of hydrogen produced by the reduction of water. The experimental results on pre-cracked specimens revealed no susceptibility of cast steel to stress corrosion cracking under model repository conditions. No crack growth was detected on compact DCB specimens exposed in aerobic and anaerobic groundwaters at 80 and 140 o C for 16-24 months. Cast steel remains a candidate material for high-level waste containers. As expected from thermodynamic considerations no hydrogen could be detected from copper immersed in model groundwaters at 50 o C. Hydrogen is evolved from corroding steel under anaerobic conditions. Hydrogen evolution due to corrosion of iron or steel in waste repositories has to be considered in any safety analysis; the amounts produced can be significant. Evidence todate suggests that both cast steel and copper are suitable container materials. Because the corrosion behaviour of both materials is sensitive to service conditions, in particular length of the aerobic phase, groundwater chemistry and temperature, further testing should be undertaken when a specific site has been identified. (author) 9 tabs., 11 figs., 25 refs

Survey of degradation modes of candidate materials for high-level radioactive-waste disposal containers

International Nuclear Information System (INIS)

Gdowski, G.E.; Bullen, D.B.

1988-08-01

Three copper-based alloys and three iron- to nickel-based austenitic alloys are being considered as possible materials for fabrication of containers for disposal of high-level radioactive waste. This waste will include spent fuel assemblies from reactors as well as high-level waste in borosilicate glass and will be sent to the prospective site at Yucca Mountain, Nevada, for disposal. The containers must maintain substantially complete containment for at least 300 yr and perhaps as long as 1000 yr. During the first 50 yr after emplacement, they must be retrievable from the disposal site. Shortly after the containers are emplaced in the repository, they will be exposed to high temperatures and high gamma radiation fields from the decay of the high-level waste. This volume surveys the available data on oxidation and corrosion of the iron- to nickel-based austenitic materials (Types 304L and 316L stainless steels and Alloy 825) and the copper-based alloy materials [CDA 102 (oxygen-free copper), CDA 613 (Cu-7Al), and CDA 715 (Cu-30Ni)], which are the present candidates for fabrication of the containers. Studies that provided a large amount of data are highlighted, and those areas in which little data exists are identified. Examples of successful applications of these materials are given. On the basis of resistance to oxidation and general corrosion, the austenitic materials are ranked as follows: Alloy 825 (best), Type 316L stainless steel, and then Type 304L stainless steel (worst). For the copper-based materials, the ranking is as follows: CDA 715 and CDA 613 (both best), and CDA 102 (worst). 110 refs., 30 figs., 13 tabs

Survey of degradation modes of candidate materials for high-level radioactive-waste disposal containers

Energy Technology Data Exchange (ETDEWEB)

Gdowski, G.E.; Bullen, D.B. (Science and Engineering Associates, Inc., Pleasanton, CA (USA))

1988-08-01

Three copper-based alloys and three iron- to nickel-based austenitic alloys are being considered as possible materials for fabrication of containers for disposal of high-level radioactive waste. This waste will include spent fuel assemblies from reactors as well as high-level waste in borosilicate glass and will be sent to the prospective site at Yucca Mountain, Nevada, for disposal. The containers must maintain substantially complete containment for at least 300 yr and perhaps as long as 1000 yr. During the first 50 yr after emplacement, they must be retrievable from the disposal site. Shortly after the containers are emplaced in the repository, they will be exposed to high temperatures and high gamma radiation fields from the decay of the high-level waste. This volume surveys the available data on oxidation and corrosion of the iron- to nickel-based austenitic materials (Types 304L and 316L stainless steels and Alloy 825) and the copper-based alloy materials (CDA 102 (oxygen-free copper), CDA 613 (Cu-7Al), and CDA 715 (Cu-30Ni)), which are the present candidates for fabrication of the containers. Studies that provided a large amount of data are highlighted, and those areas in which little data exists are identified. Examples of successful applications of these materials are given. On the basis of resistance to oxidation and general corrosion, the austenitic materials are ranked as follows: Alloy 825 (best), Type 316L stainless steel, and then Type 304L stainless steel (worst). For the copper-based materials, the ranking is as follows: CDA 715 and CDA 613 (both best), and CDA 102 (worst). 110 refs., 30 figs., 13 tabs.

Containers for the transport of radioactive materials

International Nuclear Information System (INIS)

Bochard, C.

1975-01-01

The container for heat evolving radioactive materials has a metallic outer casing formed with outwardly projecting heat dissipating or cooling members, such as pins or fins, while each of its ends is formed with a flat flange which extends radially beyond the outer ends of the cooling members. A perforated wall extends between the flanges to define with same and with the periphery of the outer casing an annular space within which the cooling members are enclosed. This perforated wall is adapted to support a flexible covering sleeve the ends of which are clamped by inflatable seals between the periphery of the flanges and outer rings removably secured to the latter. Spraying means are provided within the aforesaid space to permit of projecting an uncontaminated liquid on the cooling members to cool the container before and/or while the latter is immersed in a loading and unloading pond with the sleeve mounted in position. The lower flange is provided with liquid collecting and evacuating means and compressed air may be injected into the said space to force the collected liquid outwardly. (auth)

High-temperature thermal storage systems for advanced solar receivers materials selections

Science.gov (United States)

Wilson, D. F.; Devan, J. H.; Howell, M.

1990-01-01

Advanced space power systems that use solar energy and Brayton or Stirling heat engines require thermal energy storage (TES) systems to operate continuously through periods of shade. The receiver storage units, key elements in both Brayton and Stirling systems, are designed to use the latent heat of fusion of phase-change materials (PCMs). The power systems under current consideration for near-future National Aeronautics and Space Administration space missions require working fluid temperatures in the 1100 to 1400 K range. The PCMs under current investigation that gave liquid temperatures within this range are the fluoride family of salts. However, these salts have low thermal conductivity, which causes large temperature gradients in the storage systems. Improvements can be obtained, however, with the use of thermal conductivity enhancements or metallic PCMs. In fact, if suitable containment materials can be found, the use of metallic PCMs would virtually eliminate the orbit associated temperature variations in TES systems. The high thermal conductivity and generally low volume change on melting of germanium and alloys based on silicon make them attractive for storage of thermal energy in space power systems. An approach to solving the containment problem, involving both chemical and physical compatibility, preparation of NiSi/NiSi2, and initial results for containment of germanium and NiSi/NiSi2, are presented.

Evaluation of Nystatin Containing Chitosan Hydrogels as Potential Dual Action Bio-Active Restorative Materials: in Vitro Approach

Directory of Open Access Journals (Sweden)

V. Tamara Perchyonok

2014-11-01

Full Text Available Healing is a specific biological process related to the general phenomenon of growth and tissue regeneration and is a process generally affected by several systemic conditions or as detrimental side-effects of chemotherapy- and radiotherapy-induced inflammation of the oral mucosa. The objectives of this study is to evaluate the novel chitosan based functional drug delivery systems, which can be successfully incorporated into “dual action bioactive restorative materials”, capable of inducing in vitro improved wound healing prototype and containing an antibiotic, such as nystatin, krill oil as an antioxidant and hydroxyapatite as a molecular bone scaffold, which is naturally present in bone and is reported to be successfully used in promoting bone integration when implanted as well as promoting healing. The hydrogels were prepared using a protocol as previously reported by us. The physico-chemical features, including surface morphology (SEM, release behaviors, stability of the therapeutic agent-antioxidant-chitosan, were measured and compared to the earlier reported chitosan-antioxidant containing hydrogels. Structural investigations of the reactive surface of the hydrogel are reported. Release of nystatin was investigated for all newly prepared hydrogels. Bio-adhesive studies were performed in order to assess the suitability of these designer materials. Free radical defense capacity of the biomaterials was evaluated using established in vitro model. The bio-adhesive capacity of the materials in the in vitro system was tested and quantified. It was found that the favorable synergistic effect of free radical built-in defense mechanism of the new functional materials increased sustainable bio-adhesion and therefore acted as a functional multi-dimensional restorative material with potential application in wound healing in vitro.

Effluent Containment System for space thermal nuclear propulsion ground test facilities

International Nuclear Information System (INIS)

1995-08-01

This report presents the research and development study work performed for the Space Reactor Power System Division of the U.S. Department of Energy on an innovative ECS that would be used during ground testing of a space nuclear thermal rocket engine. A significant portion of the ground test facilities for a space nuclear thermal propulsion engine are the effluent treatment and containment systems. The proposed ECS configuration developed recycles all engine coolant media and does not impact the environment by venting radioactive material. All coolant media, hydrogen and water, are collected, treated for removal of radioactive particulates, and recycled for use in subsequent tests until the end of the facility life. Radioactive materials removed by the treatment systems are recovered, stored for decay of short-lived isotopes, or packaged for disposal as waste. At the end of the useful life, the facility will be decontaminated and dismantled for disposal

Calculations of radiation damage in target, container and window materials for spallation neutron sources

International Nuclear Information System (INIS)

Wechsler, M.S.; Mansur, L.K.

1996-01-01

Radiation damage in target, container, and window materials for spallation neutron sources is am important factor in the design of target stations for accelerator-driver transmutation technologies. Calculations are described that use the LAHET and SPECTER codes to obtain displacement and helium production rates in tungsten, 316 stainless steel, and Inconel 718, which are major target, container, and window materials, respectively. Results are compared for the three materials, based on neutron spectra for NSNS and ATW spallation neutron sources, where the neutron fluxes are normalized to give the same flux of neutrons of all energies

Container material for the disposal of highly radioactive wastes: corrosion chemistry aspects

International Nuclear Information System (INIS)

Grauer, R.

1984-08-01

Prior to disposal in crystalline formations it is planned to enclose vitrified highly radioactive waste from nuclear power plants in metallic containers ensuring their isolation from the groundwater for at least 1,000 years. Appropriate metals can be either thermodynamically stable in the repository environment (such as copper), passive materials with very low corrosion rates (titanium, nickel alloys), or metals such as cast iron or unalloyed cast steels which, although they corrode, can be used in sections thick enough to allow for this corrosion. The first part of the report presents the essentials of corrosion science in order to enable even a non-specialist to follow the considerations and arguments necessary to choose the material and design the container against corrosion. Following this, the principles of the long-term extrapolation of corrosion behaviour are discussed. The second part summarizes and comments upon the literature search carried out to identify published results relevant to corrosion in a repository environment. Results of archeaological studies are included wherever possible. Not only the general corrosion behaviour but also localized corrosion and stress corrosion cracking are considered, and the influence of hydrogen on the material behaviour is discussed. Taking the corrosion behaviour as criterion, the author suggests the use either of copper or of cast iron or steel as an appropriate container material. The report concludes with proposals for further studies. (Auth.)

Design of reactor containment systems for nuclear power plants. Safety guide

International Nuclear Information System (INIS)

2008-01-01

This Safety Guide was prepared under the IAEA programme for safety standards for nuclear power plants. It is a revision of the Safety Guide on Design of the Reactor Containment Systems in Nuclear Power Plants (Safety Series No. 50-Sg-D1) issued in 1985 and supplements the Safety Requirements publication on Safety of Nuclear Power Plants: Design. The present Safety Guide was prepared on the basis of a systematic review of the relevant publications, including the Safety of Nuclear Power Plants: Design, the Safety fundamentals publication on The Safety of Nuclear Installations, Safety Guides, INSAG Reports, a Technical Report and other publications covering the safety of nuclear power plants. 1.2. The confinement of radioactive material in a nuclear plant, including the control of discharges and the minimization of releases, is a fundamental safety function to be ensured in normal operational modes, for anticipated operational occurrences, in design basis accidents and, to the extent practicable, in selected beyond design basis accidents. In accordance with the concept of defence in depth, this fundamental safety function is achieved by means of several barriers and levels of defence. In most designs, the third and fourth levels of defence are achieved mainly by means of a strong structure enveloping the nuclear reactor. This structure is called the 'containment structure' or simply the 'containment'. This definition also applies to double wall containments. 1.3. The containment structure also protects the reactor against external events and provides radiation shielding in operational states and accident conditions. The containment structure and its associated systems with the functions of isolation, energy management, and control of radionuclides and combustible gases are referred to as the containment systems

Design of reactor containment systems for nuclear power plants. Safety guide

International Nuclear Information System (INIS)

2004-01-01

This Safety Guide was prepared under the IAEA programme for safety standards for nuclear power plants. It is a revision of the Safety Guide on Design of the Reactor Containment Systems in Nuclear Power Plants (Safety Series No. 50-Sg-D1) issued in 1985 and supplements the Safety Requirements publication on Safety of Nuclear Power Plants: Design. The present Safety Guide was prepared on the basis of a systematic review of the relevant publications, including the Safety of Nuclear Power Plants: Design, the Safety fundamentals publication on The Safety of Nuclear Installations, Safety Guides, INSAG Reports, a Technical Report and other publications covering the safety of nuclear power plants. 1.2. The confinement of radioactive material in a nuclear plant, including the control of discharges and the minimization of releases, is a fundamental safety function to be ensured in normal operational modes, for anticipated operational occurrences, in design basis accidents and, to the extent practicable, in selected beyond design basis accidents. In accordance with the concept of defence in depth, this fundamental safety function is achieved by means of several barriers and levels of defence. In most designs, the third and fourth levels of defence are achieved mainly by means of a strong structure enveloping the nuclear reactor. This structure is called the 'containment structure' or simply the 'containment'. This definition also applies to double wall containments. 1.3. The containment structure also protects the reactor against external events and provides radiation shielding in operational states and accident conditions. The containment structure and its associated systems with the functions of isolation, energy management, and control of radionuclides and combustible gases are referred to as the containment systems

Standard practice for sampling special nuclear materials in multi-container lots

CERN Document Server

American Society for Testing and Materials. Philadelphia

1987-01-01

1.1 This practice provides an aid in designing a sampling and analysis plan for the purpose of minimizing random error in the measurement of the amount of nuclear material in a lot consisting of several containers. The problem addressed is the selection of the number of containers to be sampled, the number of samples to be taken from each sampled container, and the number of aliquot analyses to be performed on each sample. 1.2 This practice provides examples for application as well as the necessary development for understanding the statistics involved. The uniqueness of most situations does not allow presentation of step-by-step procedures for designing sampling plans. It is recommended that a statistician experienced in materials sampling be consulted when developing such plans. 1.3 The values stated in SI units are to be regarded as the standard. 1.4 This standard does not purport to address all of the safety problems, if any, associated with its use. It is the responsibility of the user of this standar...

Nuclear Resonance Fluorescence and Isotopic Mapping of Containers

Science.gov (United States)

Johnson, Micah S.; McNabb, Dennis P.

2009-03-01

National security programs have expressed interest in developing systems to isotopically map shipping containers, fuel assemblies, and waste barrels for various materials including special nuclear material (SNM). Current radiographic systems offer little more than an ambiguous density silhouette of a container's contents. In this paper we will present a system being developed at LLNL to isotopically map containers using the nuclear resonance fluorescence (NRF) method. Recent experimental measurements on NRF strengths in SNM are discussed.

Basics of control system material in iron foundry

Directory of Open Access Journals (Sweden)

J. Sitko

2011-07-01

Full Text Available The article is taking into account problems of preparing the production of cast-iron casts with reference to correctnesses functioning of processes supplementing, containing elements the system of supply necessary materials and the tool used in order processing production. Methods and chosen models realization elements of production process and their influence on the efficiency process were characterized.

Dose and radon measurements inside houses containing ash as building material

International Nuclear Information System (INIS)

Bodnar, R.; Lendvai, Z.; Somlai, J.; Nemeth, C.

1996-01-01

Radon concentration and external dose have been measured in dwellings that contain by-products of coal burning for building materials. The concentrations of 40 K, 232 Th, 238 U and 226 Ra have been determined in the materials. The date are analyzed according to indices frequently used for decision of utilizing the by-products. The observed daily fluctuation of the radon concentration in dwellings might exceed a factor of 5. (author)

Tritium containment in fusion facilities

International Nuclear Information System (INIS)

Anderson, J.L.

1978-01-01

The key environmental control systems that have been identified and are being developed are listed. A brief description of each of the following systems is given: primary process materials, permeation barriers, secondary containment, tritium waste treatment, emergency tritium cleanup, maintenance procedures, and tertiary containment

Selection criteria for container materials at the proposed Yucca Mountain high level nuclear waste repository

International Nuclear Information System (INIS)

Halsey, W.G.

1989-11-01

A geological repository has been proposed for the permanent disposal of the nation's high level nuclear waste at Yucca Mountain in the Nevada desert. The containers for this waste must remain intact for the unprecedented service lifetime of 1000 years. A combination of engineering, regulatory, and licensing requirements complicate the container material selection. In parallel to gathering information regarding the Yucca Mountain service environment and material performance data, a set of selection criteria have been established which compare candidate materials to the performance requirements, and allow a quantitative comparison of candidates. These criteria assign relative weighting to varied topic areas such as mechanical properties, corrosion resistance, fabricability, and cost. Considering the long service life of the waste containers, it is not surprising that the corrosion behavior of the material is a dominant factor. 7 refs

19 CFR 10.462 - Packing materials and containers for shipment.

Science.gov (United States)

2010-04-01

... Free Trade Agreement Rules of Origin § 10.462 Packing materials and containers for shipment. (a... disregarded in determining the regional value content of a good imported into the United States. Accordingly, in applying either the build-down or build-up method for determining the regional value content of...

Performance of Cement Containing Laterite as Supplementary Cementing Material

Directory of Open Access Journals (Sweden)

Abbas Bukhari, Z. S.

2013-03-01

Full Text Available The utilization of different industrial waste, by-products or other materials such as ground granulated blast furnace slag, silica fume, fly ash, limestone, and kiln dust, etc. as supplemen- tary cementing materials has received considerable attention in recent years. A study has been conducted to look into the performance of laterite as Supplementary Cementing Materials (SCM. The study focuses on compressive strength performance of blended cement containing different percentage of laterite. The cement is replaced accordingly with percentage of 2 %, 5 %, 7 % and 10 % by weight. In addition, the effect of use of three chemically different laterites have been studied on physical performance of cement as in setting time, Le-Chatlier expansion, loss on ignition, insoluble residue, free lime and specifically compressive strength of cement cubes tested at the age of 3, 7, and 28 days. The results show that the strength of cement blended with laterite as SCM is enhanced. Key words: Portland cement, supplementary cementing materials (SCM, laterite, compressive strength KUI – 6/2013 Received January 4, 2012 Accepted February 11, 2013

Method for contamination control and barrier apparatus with filter for containing waste materials that include dangerous particulate matter

Science.gov (United States)

Pinson, Paul A.

1998-01-01

A container for hazardous waste materials that includes air or other gas carrying dangerous particulate matter has incorporated in barrier material, preferably in the form of a flexible sheet, one or more filters for the dangerous particulate matter sealably attached to such barrier material. The filter is preferably a HEPA type filter and is preferably chemically bonded to the barrier materials. The filter or filters are preferably flexibly bonded to the barrier material marginally and peripherally of the filter or marginally and peripherally of air or other gas outlet openings in the barrier material, which may be a plastic bag. The filter may be provided with a backing panel of barrier material having an opening or openings for the passage of air or other gas into the filter or filters. Such backing panel is bonded marginally and peripherally thereof to the barrier material or to both it and the filter or filters. A coupling or couplings for deflating and inflating the container may be incorporated. Confining a hazardous waste material in such a container, rapidly deflating the container and disposing of the container, constitutes one aspect of the method of the invention. The chemical bonding procedure for producing the container constitutes another aspect of the method of the invention.

Method for contamination control and barrier apparatus with filter for containing waste materials that include dangerous particulate matter

International Nuclear Information System (INIS)

Pinson, P.A.

1998-01-01

A container for hazardous waste materials that includes air or other gas carrying dangerous particulate matter has incorporated barrier material, preferably in the form of a flexible sheet, and one or more filters for the dangerous particulate matter sealably attached to such barrier material. The filter is preferably a HEPA type filter and is preferably chemically bonded to the barrier materials. The filter or filters are preferably flexibly bonded to the barrier material marginally and peripherally of the filter or marginally and peripherally of air or other gas outlet openings in the barrier material, which may be a plastic bag. The filter may be provided with a backing panel of barrier material having an opening or openings for the passage of air or other gas into the filter or filters. Such backing panel is bonded marginally and peripherally thereof to the barrier material or to both it and the filter or filters. A coupling or couplings for deflating and inflating the container may be incorporated. Confining a hazardous waste material in such a container, rapidly deflating the container and disposing of the container, constitutes one aspect of the method of the invention. The chemical bonding procedure for producing the container constitutes another aspect of the method of the invention. 3 figs

Containments for consolidated nuclear steam systems

International Nuclear Information System (INIS)

Jabsen, F.S.

1978-01-01

A containment system for a consolidated nuclear steam system incorporating a nuclear core, steam generator and reactor coolant pumps within a single pressure vessel is described which is designed to provide radiation shielding and pressure suppression. Design details, including those for the dry well and wet well of the containment, are given. (UK)

Corrosion of container materials for disposal of high-level radioactive wastes

Energy Technology Data Exchange (ETDEWEB)

Chun, K.S.; Park, H.S.; Yeon, J.W.; Ha, Y.K. [Korea Atomic Energy Research Institute, Taejon (Korea)

1999-01-01

In the corrosion aspect of container for the deep geological disposal of high-level radioactive waste, disposal concepts and the related container materials, which have been developed by advanced countries, have been reviewed. The disposal circumstances could be divided into the saturated and the unsaturated zones. The candidate materials in the countries, which consider the disposal in the unsaturated zone, are the corrosion resistant materials such as supper alloys and stainless steels, but those in the saturated zone is cupper, one of the corrosion allowable materials. By the results of the pitting corrosion test of sensitized stainless steels (such as 304, 304L, 316 and 316L), pitting potential is decreased with the degree of sensitization and the pitting corrosion resistance of 316L is higher than others. And so, the long-term corrosion experiment with 316L stainless steel specimens, sebsitized and non-sensitized, under the compacted bentonite and synthetic granitic groundwater has been being carried out. The results from the experiment for 12 months indicate that no evidence of pitting corrosion of the specimens has been observed but the crevice corrosion has occurred on the sensitized specimens even for 3 months. (author). 33 refs., 19 figs., 10 tabs.

Processing Uranium-Bearing Materials Containing Coal and Loam

Energy Technology Data Exchange (ETDEWEB)

Civin, V; Prochazka, J [Research and Development Laboratory No. 3 of the Uranium Industry, Prague, Czechoslovakia (Czech Republic)

1967-06-15

Among the ores which are classified as low-grade in the CSSR are mixtures of coal and bentonitic loam of tertiary origin, containing approximately 0.1% U and with a moisture content at times well above 20-30%. The uranium is held mainly by the carbonaceous component. Conventional processing of these materials presents various difficulties which are not easily overcome. During leaching the pulp thickens and frequently becomes pasty, due to the presence of montmorillonites. Further complications arise from the high sorption capacity of the materials (again primarily due to montmorillonites) and poor sedimentation of the viscous pulps. In addition, the materials are highly refractory to the leaching agents. The paper presents experience gained in solving the problems of processing these ores. The following basic routes were explored: (1) separation of the carbonaceous and loamy components: The organic component appears to be the main activity carrier. Processing the concentrated material upon separation of the inactive or less active loam may not only remove the thixotropic behaviour but also substantially reduce the cost of the ore treatment; (2) 'liquifying' the pulps or preventing the thickening of the pulp by addition of suitable agents; (3) joint acid or carbonate processing of the materials in question with current ore types; (4) removal or suppression of thixotropic behaviour by thermal pretreatment of the material; and (5) application of the 'acid cure' method. The first method appears to be the most effective, but it presents considerable difficulties due to the extreme dispersion of the carbonaceous phase and further research is being carried out. Methods 2 and 3 proved to be unacceptable. Method 4, which includes roasting at 300-400{sup o}C, is now being operated on an industrial scale. The final method has also shown definite advantages for particular deposits of high montmorillonite content material. (author)

Safety Standard for Oxygen and Oxygen Systems: Guidelines for Oxygen System Design, Materials Selection, Operations, Storage, and Transportation

Science.gov (United States)

1996-01-01

NASA's standard for oxygen system design, materials selection, operation, and transportation is presented. Minimum guidelines applicable to NASA Headquarters and all NASA Field Installations are contained.

Hybrid silica luminescent materials based on lanthanide-containing lyotropic liquid crystal with polarized emission

Energy Technology Data Exchange (ETDEWEB)

Selivanova, N.M., E-mail: natsel@mail.ru [Kazan National Research Technological University, 68 Karl Marx Str., Kazan 420015 (Russian Federation); Vandyukov, A.E.; Gubaidullin, A.T. [A.E. Arbuzov Institute of Organic and Physical Chemistry of the Kazan Scientific Center of the Russian Academy of Sciences, 8 Acad. Arbuzov Str., Kazan 420088 (Russian Federation); Galyametdinov, Y.G. [Kazan National Research Technological University, 68 Karl Marx Str., Kazan 420015 (Russian Federation)

2014-11-14

This paper represents the template method for synthesis of hybrid silica films based on Ln-containing lyotropic liquid crystal and characterized by efficient luminescence. Luminescence films were prepared in situ by the sol–gel processes. Lyotropic liquid crystal (LLC) mesophases C{sub 12}H{sub 25}O(CH{sub 2}CH{sub 2}O){sub 10}H/Ln(NO{sub 3}){sub 3}·6H{sub 2}O/H{sub 2}O containing Ln (III) ions (Dy, Tb, Eu) were used as template. Polarized optical microscopy, X-ray powder diffraction, and FT-IR-spectroscopy were used for characterization of liquid crystal mesophases and hybrid films. The morphology of composite films was studied by the atomic force microscopy method (AFM). The optical properties of the resulting materials were evaluated. It was found that hybrid silica films demonstrate significant increase of their lifetime in comparison with an LLC system. New effects of linearly polarized emission revealed for Ln-containing hybrid silica films. Polarization in lanthanide-containing hybrid composites indicates that silica precursor causes orientation of emitting ions. - Highlights: • We suggest a new simple approach for creating luminescence hybrid silica films. • Ln-containing hybrid silica films demonstrate yellow, green and red emissions. • Tb(III)-containing hybrid film have a high lifetime. • We report effects of linearly polarized emission in hybrid film.

12 CFR 503.2 - Exemptions of records containing investigatory material compiled for law enforcement purposes.

Science.gov (United States)

2010-01-01

... 12 Banks and Banking 5 2010-01-01 2010-01-01 false Exemptions of records containing investigatory material compiled for law enforcement purposes. 503.2 Section 503.2 Banks and Banking OFFICE OF THRIFT SUPERVISION, DEPARTMENT OF THE TREASURY PRIVACY ACT § 503.2 Exemptions of records containing investigatory material compiled for law enforcement...

Numerical Simulation on Dense Packing of Granular Materials by Container Oscillation

OpenAIRE

Jun Liu; Dongxu You

2013-01-01

The packing of granular materials is a basic and important problem in geomechanics. An approach, which generates dense packing of spheres confined in cylindrical and cuboidal containers in three steps, is introduced in this work. A loose packing structure is first generated by means of a reference lattice method. Then a dense packing structure is obtained in a container by simulating dropping of particles under gravitational forces. Furthermore, a scheme that makes the bottom boundary fluctua...

Shipping container for a bottle of radioactive material

International Nuclear Information System (INIS)

Soldan, D.W.

1975-01-01

A shipping container for a bottle of radioactive material comprises a can having a cavity therein for receiving the bottle, a screw cap for the can and the cavity, and an annular bottle retainer extending downwardly in the cavity from its upper end having an outwardly extending flange at its upper end clamped between the cap and the upper end of the cavity and an inwardly extending flange at its lower end receiving the neck of the bottle. The cap carries a sponge to absorb spillage from the bottle. (U.S.)

Alkaline degradation of organic materials contained in TRU wastes under repository conditions

International Nuclear Information System (INIS)

Otsuka, Yoshiki; Banba, Tsunetaka

2007-09-01

Alkaline degradation tests for 9 organic materials were conducted under the conditions of TRU waste disposal: anaerobic alkaline conditions. The tests were carried out at 90degC for 91 days. The sample materials for the tests were selected from the standpoint of constituent organic materials of TRU wastes. It has been found that cellulose and plastic solidified products are degraded relatively easily and that rubbers are difficult to degrade. It could be presumed that the alkaline degradation of organic materials occurs starting from the functional group in the material. Therefore, the degree of degradation difficulty is expected to be dependent on the kinds of functional group contained in the organic material. (author)

Fluorine uptake into human enamel around fluoride-containing dental materials during cariogenic pH cycling

Energy Technology Data Exchange (ETDEWEB)

Komatsu, H. [Graduate School of Dental Medicine, Hokkaido University, Kita-13, Nishi-7, Kita-ku, Sapporo 060-8586 (Japan)], E-mail: kom@den.hokudai.ac.jp; Yamamoto, H. [Graduate School of Dentistry, Osaka University, 1-8 Yamada-Oka, Suita 565-0871 (Japan); Nomachi, M. [Graduate School of Science, Osaka University, 1-1 Machikaneyama, Toyonaka 560-0043 (Japan); Yasuda, K. [The Wakasa wan Energy Research Center, 64-52-1 Hase, Tsuruga 914-0192 (Japan); Matsuda, Y.; Kinugawa, M.; Kijimura, T.; Sano, H. [Graduate School of Dental Medicine, Hokkaido University, Kita-13, Nishi-7, Kita-ku, Sapporo 060-8586 (Japan); Satou, T.; Oikawa, S.; Kamiya, T. [Advanced Radiation Technology, TARRI, JAEA, 1233 Watanuki-machi, Takasaki 370-1292 (Japan)

2009-06-15

Using PIGE (Proton Induced Gamma Emission) technique at TARRI (Takasaki Advanced Radiation Research Institute), Japan, we measured fluorine (F) uptake into the tooth enamel around two fluoride-containing materials during caries progression using pH cycling. Class V cavities in extracted human teeth were drilled and filled with fluoride-containing materials (i.e. 'Fuji IX' (FN) and 'UniFil flow with MEGA bond' (UF)) and a non-fluoride-containing material (i.e. 'SOLARE with MEGA bond' (SO)). Three 120 {mu}m longitudinal sections including the filling material were obtained from each tooth. In order to simulate daily acid attack occurring in the oral cavity, the pH cycling (pH 6.8-4.5) was carried out for 1, 3 and 5 weeks, separately. After pH cycling, the caries progression in all specimens was observed using transverse microradiography (TMR). The F and calcium distributions of the specimens were evaluated using PIGE and PIXE techniques. The F distribution of the specimens clearly showed the F uptake from FN into enamel adjacent to the filling material, while the F uptakes from UF and SO were not detected. For UF, the MEGA bond (non-fluoride-containing) between the tooth and UniFil flow interfered with the F absorption into the tooth. For FN, the amount of F uptake into the subsurface enamel increased during pH cycling. The amount of F uptake in 5-week pH cycling had significantly higher value compared to those in 1- and 3-week pH cycling. For UF and SO, there were no significant differences between the different durations of pH cycling. Among fluoride-containing materials, there were some differences in the F uptake with increased pH cycling, which could possibly lead to obtaining difference in clinical performance. The data obtained using PIGE and PIXE techniques were useful in understanding the benefit of fluorine by means of fluoride-containing material for preventing caries.

Fluorine uptake into human enamel around fluoride-containing dental materials during cariogenic pH cycling

International Nuclear Information System (INIS)

Komatsu, H.; Yamamoto, H.; Nomachi, M.; Yasuda, K.; Matsuda, Y.; Kinugawa, M.; Kijimura, T.; Sano, H.; Satou, T.; Oikawa, S.; Kamiya, T.

2009-01-01

Using PIGE (Proton Induced Gamma Emission) technique at TARRI (Takasaki Advanced Radiation Research Institute), Japan, we measured fluorine (F) uptake into the tooth enamel around two fluoride-containing materials during caries progression using pH cycling. Class V cavities in extracted human teeth were drilled and filled with fluoride-containing materials (i.e. 'Fuji IX' (FN) and 'UniFil flow with MEGA bond' (UF)) and a non-fluoride-containing material (i.e. 'SOLARE with MEGA bond' (SO)). Three 120 μm longitudinal sections including the filling material were obtained from each tooth. In order to simulate daily acid attack occurring in the oral cavity, the pH cycling (pH 6.8-4.5) was carried out for 1, 3 and 5 weeks, separately. After pH cycling, the caries progression in all specimens was observed using transverse microradiography (TMR). The F and calcium distributions of the specimens were evaluated using PIGE and PIXE techniques. The F distribution of the specimens clearly showed the F uptake from FN into enamel adjacent to the filling material, while the F uptakes from UF and SO were not detected. For UF, the MEGA bond (non-fluoride-containing) between the tooth and UniFil flow interfered with the F absorption into the tooth. For FN, the amount of F uptake into the subsurface enamel increased during pH cycling. The amount of F uptake in 5-week pH cycling had significantly higher value compared to those in 1- and 3-week pH cycling. For UF and SO, there were no significant differences between the different durations of pH cycling. Among fluoride-containing materials, there were some differences in the F uptake with increased pH cycling, which could possibly lead to obtaining difference in clinical performance. The data obtained using PIGE and PIXE techniques were useful in understanding the benefit of fluorine by means of fluoride-containing material for preventing caries.

A review of a radioactive material shipping container including design, testing, upgrading compliance program and shipping logistics

International Nuclear Information System (INIS)

Celovsky, A.; Lesco, R.; Gale, B.; Sypes, J.

2003-01-01

Ten years ago Atomic Energy of Canada developed a Type B(U)-85 shipping container for the global transport of highly radioactive materials. This paper reviews the development of the container, including a summary of the design requirements, a review of the selected materials and key design elements, and the results of the major qualification tests (drop testing, fire test, leak tightness testing, and shielding integrity tests). As a result of the testing, improvements to the structural, thermal and containment design were made. Such improvements, and reasons thereof, are noted. Also provided is a summary of the additional analysis work required to upgrade the package from a Type B(U) to a Type B(F), i.e. essentially upgrading the container to include fissile radioisotopes to the authorized radioactive contents list. Having a certified shipping container is only one aspect governing the global shipments of radioactive material. By necessity the shipment of radioactive material is a highly regulated environment. This paper also explores the experiences with other key aspects of radioactive shipments, including the service procedures used to maintain the container certification, the associated compliance program for radioactive material shipments, and the shipping logistics involved in the transport. (author)

Luminescent hybrid materials functionalized with lanthanide ethylenodiaminotetraacetate complexes containing β-diketonate as antenna ligands

Energy Technology Data Exchange (ETDEWEB)

Aguiar, Franklin P.; Costa, Israel F.; Espínola, José Geraldo P.; Faustino, Wagner M.; Moura, Jandeilson L. [Departamento de Química-Universidade Federal da Paraíba, 58051-970 João Pessoa, PB (Brazil); Brito, Hermi F.; Paolini, Tiago B. [Departamento de Química Fundamental-Instituto de Química da Universidade de São Paulo, 05508-900 São Paulo, SP (Brazil); Felinto, Maria Cláudia F.C. [Instituto de Pesquisas energéticas e Nucleares-IPEN, 05508-900 São Paulo, SP (Brazil); Teotonio, Ercules E.S., E-mail: teotonioees@quimica.ufpb.br [Departamento de Química-Universidade Federal da Paraíba, 58051-970 João Pessoa, PB (Brazil)

2016-02-15

Three organic–inorganic hybrid materials based on silica gel functionalized with (3-aminopropyl)trimethoxysilane (APTS), [3-(2-aminoetilamino)-propil]-trimetoxissilano (DAPTS) and 3-[2-(2-aminoetilamino)etilamino] propiltrimetoxysilane (TAPTS) and subsequently modified with EDTA derivative were prepared by nonhomogeneous route and were then characterized. The resulting materials named SilXN-EDTA (X=1 for APTS, 2 for DAPTS and 3 for TAPTS) were used to obtain new lanthanide Ln{sup 3+}-β-diketonate (Ln{sup 3+}=Eu{sup 3+}, Gd{sup 3+} and Tb{sup 3+}) complexes covalently linked to the functionalized silica gel surfaces (named SilXN-EDTALn-dik, dik=tta, dbm, bzac and acac). The photophysical properties of the new luminescent materials were investigated and compared with those with similar system presenting water molecules coordinated to the lanthanide ions, SilXN-EDTALn-H{sub 2}O. The SilXN-EDTAEu-dik and SilXN-EDTATb-dik systems displayed characteristic red and green luminescence when excited by UV radiation. Furthermore, the quantitative results showed that the emission quantum efficiency (η), experimental intensity parameters Ω{sub 2} and Ω{sub 4}, and Einstein's emission coefficient (A{sub 0J}) of the SilXN-EDTAEu-dik materials were largely dependent on the ligands. Based on the luminescence data, the most efficient intramolecular energy transfer processes were found to the SilXN-EDTAEu-dik (dik: tta and dbm) and SilXN-EDTATb-acac materials, which exhibited more pure emission colors. These materials are promising red and green phosphors, respectively. - Highlights: • New highly luminescent hybrid materials containing lanthanide-EDTA complexes. • The effect of three silylanting agent on the adsorption and luminescent properties has been studied. • The luminescence sensitizing by different β-diketonate ligands have been investigated.

A hyperspectral X-ray computed tomography system for enhanced material identification

Science.gov (United States)

Wu, Xiaomei; Wang, Qian; Ma, Jinlei; Zhang, Wei; Li, Po; Fang, Zheng

2017-08-01

X-ray computed tomography (CT) can distinguish different materials according to their absorption characteristics. The hyperspectral X-ray CT (HXCT) system proposed in the present work reconstructs each voxel according to its X-ray absorption spectral characteristics. In contrast to a dual-energy or multi-energy CT system, HXCT employs cadmium telluride (CdTe) as the x-ray detector, which provides higher spectral resolution and separate spectral lines according to the material's photon-counter working principle. In this paper, a specimen containing ten different polymer materials randomly arranged was adopted for material identification by HXCT. The filtered back-projection algorithm was applied for image and spectral reconstruction. The first step was to sort the individual material components of the specimen according to their cross-sectional image intensity. The second step was to classify materials with similar intensities according to their reconstructed spectral characteristics. The results demonstrated the feasibility of the proposed material identification process and indicated that the proposed HXCT system has good prospects for a wide range of biomedical and industrial nondestructive testing applications.

Stress corrosion cracking of steam generator tubing materials in lead containing solution

International Nuclear Information System (INIS)

Kim, H.P.; Hwang, S.S.; Kim, J.S.; Hong, J.H.

2007-01-01

Stress corrosion cracking (SCC) in lead (Pb) containing environments has been one of key issues in the nuclear power industry since Pb had been identified as a cause of the SCC of steam generator (SG) tubing materials in some power plants. To mitigate or prevent degradation of SG tubing materials, a mechanistic understanding of SCC in Pb containing environment is needed, along with an understanding of the source and transport behaviors of Pb species in the secondary circuit. In this work, SCC behaviors of Alloy 600 in Pb containing environments were studied. Influences of microstructures of Alloy 600 and the inhibitive additives were investigated using the C-ring and the slow strain rate tests in caustic solution and demineralized water at 315 o C. Microstructures of Alloy 600 were varied by heat treatment at different temperatures. The additives examined were nickel boride (NiB) and cerium boride (CeB 6 ). The surface films were analyzed using Auger Electron Spectroscopy (AES) and Energy Dispersive X-ray Spectroscopy (EDS). The SCC mode varied with microstructure. Effectiveness of the additives in Pb containing environments is discussed. (author)

TECHNICAL GUIDANCE DOCUMENT: CONSTRUCTION QUALITY MANAGEMENT FOR REMEDIAL ACTION AND REMEDIAL DESIGN WASTE CONTAINMENT SYSTEMS

Science.gov (United States)

This Technical Guidance Document is intended to augment the numerous construction quality control and construction quality assurance (CQC and CQA) documents that are available far materials associated with waste containment systems developed for Superfund site remediation. In ge...

Containment heat removal system

International Nuclear Information System (INIS)

Wade, G.E.; Barbanti, G.; Gou, P.F.; Rao, A.S.; Hsu, L.C.

1992-01-01

This patent describes a nuclear system of a type including a containment having a nuclear reactor therein, the nuclear reactor including a pressure vessel and a core in the pressure vessel, the system. It comprises a gravity pool of coolant disposed at an elevation sufficient to permit a flow of coolant into the nuclear reactor pressure vessel against a predetermined pressure within the nuclear reactor pressure vessel; means for reducing a pressure of steam in the nuclear reactor pressure vessel to a value less than the predetermined pressure in the event of a nuclear accident, the means including a depressurization valve connected to the pressure vessel, the means further including steam heat dissipating means such dissipating means including a suppression pool; a supply of water in the suppression pool, there being a headspace in the suppression pool above the water supply; a substantial amount of air in the head space; means for feeding pressurized steam from the nuclear reactor pressure vessel to a location under a surface of the supply of water, the supply of water being effective to absorb heat sufficient to reduce steam pressure below the predetermined pressure; and a check valve for communicating the headspace with the containment, the check valve being oriented to vent air in the headspace to the containment when a pressure in the headspace exceeds a pressure in the containment by a predetermined pressure differential

49 CFR 837.3 - Published reports, material contained in the public accident investigation dockets, and accident...

Science.gov (United States)

2010-10-01

... 49 Transportation 7 2010-10-01 2010-10-01 false Published reports, material contained in the... OF RECORDS IN LEGAL PROCEEDINGS § 837.3 Published reports, material contained in the public accident... submitted, in writing, to the Public Inquiries Branch. Demands for specific published reports and studies...

Process of preparing ethanol by continuous fermentation of polysaccharide-containing materials

Energy Technology Data Exchange (ETDEWEB)

Ehnstroem, L.K.J.

1981-04-16

The invention concerns a process of preparing ethanol by continuous fermentation of polysaccharide - containing raw materials. Fermentation, hereby, occurs in one or several fermentors while dividing one stream of the fermentation liquid into a yeast-concentrate stream and a yeast-free stream and, if neccessary, a sludge stream. The yeast-concentrate stream is re-fed into the fermentor and at least part of the yeast-free stream is directed into a simple evaporator corresponding to one or several distilling stages where it is separated partially in an ethanol-enriched initial vapour stream supplying a facility to produce the desired ethanol quality, and partially in a liquid initial bottom stream re-fed at least in part into the fermentor. The characteristic feature of this new process is that a raw-material stream is fed into a closed circuit containing the fermentor and the evaporator, and that, in the evaporator, the raw-material stream is hydrolysed to a fermentable state. This hydrolysis is carried out most favourably by enzymes - preferably a gluco-amylase - at a temperature ranging from 35/sup 0/C to 75/sup 0/C.

Lignases and aldo-keto reductases for conversion of lignin-containing materials to fermentable products

Science.gov (United States)

Scharf, Michael; Sethi, Amit

2016-09-13

Termites have specialized digestive systems that overcome the lignin barrier in wood to release fermentable simple sugars. Using the termite Reticulitermes flavipes and its gut symbionts, high-throughput titanium pyrosequencing and proteomics approaches experimentally compared the effects of lignin-containing diets on host-symbiont digestome composition. Proteomic investigations and functional digestive studies with recombinant lignocellulases conducted in parallel provided strong evidence of congruence at the transcription and translational levels and provide enzymatic strategies for overcoming recalcitrant lignin barriers in biofuel feedstocks. Briefly described, therefore, the disclosure provides a system for generating a fermentable product from a lignified plant material, the system comprising a cooperating series of at least two catalytically active polypeptides, where said catalytically active polypeptides are selected from the group consisting of: cellulase Cell-1, .beta.-glu cellulase, an aldo-keto-reductase, a catalase, a laccase, and an endo-xylanase.

Development of degradation D/B system for the containment building of NPP

International Nuclear Information System (INIS)

Cho, M. S.; Song, Y. C.; Yim, J. H.; Kim, D. K.; Lee, J. S.

2001-01-01

The Degradation D/B System is developed for digitalizing the history of the Containment building of nuclear power plant. It have 6 D/B which are consist of General, Design drawing, Material, Construction, ISI·SIT·ILRT D/B. For efficient operation of the system, utilities are also developed such as the aging and repair data management program for concrete and steel structures, the data search engine with various options helping users find what they want, and the data exchange program restoring and updating input data

Risk Identification in a Smart Monitoring System Used to Preserve Artefacts Based on Textile Materials

Science.gov (United States)

Diaconescu, V. D.; Scripcariu, L.; Mătăsaru, P. D.; Diaconescu, M. R.; Ignat, C. A.

2018-06-01

Exhibited textile-materials-based artefacts can be affected by the environmental conditions. A smart monitoring system that commands an adaptive automatic environment control system is proposed for indoor exhibition spaces containing various textile artefacts. All exhibited objects are monitored by many multi-sensor nodes containing temperature, relative humidity and light sensors. Data collected periodically from the entire sensor network is stored in a database and statistically processed in order to identify and classify the environment risk. Risk consequences are analyzed depending on the risk class and the smart system commands different control measures in order to stabilize the indoor environment conditions to the recommended values and prevent material degradation.

Piezoelectric ceramic material, containing PbNb2O6, K2Nb2O6

International Nuclear Information System (INIS)

Fesenko, E.G.; Filip'ev, V.S.; Razumovskaya, O.N.; Cherner, Ya.E.; Rudkovskaya, L.M.; Zav'yalov, V.P.; Molchanova, R.A.; Kryshtop, V.G.; Panich, A.E.; Servuli, V.A.

1984-01-01

A new piezoelectric ceramic material including PbNb 2 O 6 , K 2 Nb 2 O 6 is prepared. Above the new material contains Nb 2 O 5 . The invention relates to piezotechnique. The principal advantage of this material for acoustic converters is high anisotropy of piezoelectric properties as well as high Curie temperature (T C =539-553 deg C). The composition containing 93.96 mole% PbNb 2 O 6 ; 2.48 mole% K 2 Nb 2 O 6 and 3.56 mole% Nb 2 O 5 has optimum content of parameters

Storage vessel for radiation contaminated container

International Nuclear Information System (INIS)

Sakatani, Tadatsugu.

1996-01-01

In a storage vessel of the present invention, a plurality of radiation contaminated material containing bodies are vertically stacked in a cell chamber. Then, the storage vessel comprises a containing tube for containing a plurality of the containing bodies, cooling coils wound around the containing tube, a cooling medium circulating system connected to the cooling coils and circulating cooling medium, and a heat exchanger interposed to the cooling medium circulating system for removing heat of the cooling medium. Heat of the radioactive material containing bodies is transferred to cooling air and cooling coils by way of the container tube, thereby cooling the containing bodies. By the operation of circulating pumps in a cooling medium circulation system, the cooling medium circulates through a circulation channel comprising a cooling medium transfer pipes, cooling medium branching tubes, cooling coils and the heat exchanger, then heat of the cooling medium is transferred to a heat utilizing system by way of the heat exchanger to attain effective utilization of the heat. In this case, heat can be taken out stably even when the storage amount fluctuates and heat releasing amount is reduced, and improvement of heat transfer promotes the cooling of the containing bodies, which enables minimization of the size of the storage vessel. (T.M.)

Closure for casks containing radioactive materials

International Nuclear Information System (INIS)

Hall, G.V.B.; Mallory, C.W.

1990-01-01

This patent describes an improved closure for covering and sealing an opening in a single cask for containing radioactive material, wherein the opening is characterized by a ledge. It comprises: an inner lid receivable within the opening and having a gasket means that is seatable over the ledge; an outer lid which is likewise receivable into the opening and securable therearound when the outer lid is rotated relative to the opening. The inner lid remaining stationary relative to the cask opening when the outer lid is rotated and having no torque applied thereto by the outer lid when the outer lid is rotated, and bolt means threadedly mounted through the outer lid for applying a compressive force between the inner and outer lids after the outer lid has been secured to the opening in order to depress the gasket means of the inner lid into sealing engagement with the ledge while avoiding the application of torsion between the gasket means and the ledge

Simulation of the containment spray system test PACOS PX2.2 with the integral code ASTEC and the containment code system COCOSYS

International Nuclear Information System (INIS)

Risken, Tobias; Koch, Marco K.

2011-01-01

The reactor safety research contains the analysis of postulated accidents in nuclear power plants (npp). These accidents may involve a loss of coolant from the nuclear plant's reactor coolant system, during which heat and pressure within the containment are increased. To handle these atmospheric conditions, containment spray systems are installed in various light water reactors (LWR) worldwide as a part of the accident management system. For the improvement and the safety ensurance in npp operation and accident management, numeric simulations of postulated accident scenarios are performed. The presented calculations regard the predictability of the containment spray system's effect with the integral code ASTEC and the containment code system COCOSYS, performed at Ruhr-Universitaet Bochum. Therefore the test PACOS Px2.2 is simulated, in which water is sprayed in the stratified containment atmosphere of the BMC (Battelle Modell-Containment). (orig.)

Recommended welding criteria for use in the fabrication of shipping containers for radioactive materials

International Nuclear Information System (INIS)

Monroe, R.E.; Woo, H.H.; Sears, R.G.

1984-03-01

Welding and related operations are evaluated to assess the controls required to prevent weld-related failure of shipping containers used for transportation of radioactive materials. The report includes (1) recommended criteria for controlling welding as applied to shipping containers and (2) a discussion of modifications of the recommended industry Codes as applied to shipping containers. 13 references, 2 tables

A system of nuclear material accountancy in the JAERI

International Nuclear Information System (INIS)

Kase, Toshio; Nishizawa, Satoshi; Takahashi, Yoshindo

1983-05-01

Pursuant to the domestic law and regulations revised in 1978 as to be conformed to the requirements specified in the Safeguards Agreement under the Non-Proliferation Treaty (NPT), the JAERI's system of nuclear material accountancy has been effectively developed. The system of accountancy in the JAERI is based on the information treatment by the computer. The data of nuclear material are retained batchwisely together with their complicate history reflected the inventory changes and other transactions. The reports represented these data are prepared and submitted to the IAEA through the Government every month. The inspections are frequently conducted to the JAERI to verify the material appeared in the reports. Item counting, item identification and non-destructive assay technique are brought to the verification. In some cases, seals of the Government and the IAEA are applied to the nuclear material at the inspections, as their containment measures. The surveillance camera is also installed in the facility to look whole view of reactor room and spent fuel pond. In this paper, the general safeguards application and its corresponding accountancy system on JAERI's nuclear facility are described. (author)

Demonstration of an Emergency Containment System

International Nuclear Information System (INIS)

Flanagan, T.M.; Rogers, M.L.; Wilkes, W.R.

1978-01-01

A system called an Emergency Containment System (ECS) to be used for tertiary containment of tritium was reported at the 13th Air Cleaning Conference. This system was part of the Tritium Effluent Control Laboratory then under construction at Mound Facility. A series of experiments has recently been conducted to evaluate the performance of an ECS in capturing tritium accidentally released into an operating laboratory. The ECS is an automatically actuated laboratory air detritiation system utilizing a catalytic oxidation reactor and presaturated oxide adsorption/exchange columns. In the event of an accidental release of tritium into the laboratory, the ECS is automatically activated, and quick-acting pneumatic dampers divert the laboratory air supply and exhaust through the ECS until room concentrations are returned to safe operating levels. The results of the experiments have shown that a tertiary containment of tritium is feasible. In the event of a catastrophic accident, the ECS is capable of preventing the release of a large quantity of tritium to the environment

Optoelectronic inventory system for special nuclear material

International Nuclear Information System (INIS)

Sieradzki, F.H.

1994-01-01

In support of the Department of Energy's Dismantlement Program, the Optoelectronics Characterization and Sensor Development Department 2231 at Sandia National Laboratories/New Mexico has developed an in situ nonintrusive Optoelectronic Inventory System (OIS) that has the potential for application wherever periodic inventory of selected material is desired. Using a network of fiber-optic links, the OIS retrieves and stores inventory signatures from data storage devices (which are permanently attached to material storage containers) while inherently providing electromagnetic pulse immunity and electrical noise isolation. Photovoltaic cells (located within the storage facility) convert laser diode optic power from a laser driver to electrical energy. When powered and triggered, the data storage devices sequentially output their digital inventory signatures through light-emitting diode/photo diode data links for retrieval and storage in a mobile data acquisition system. An item's exact location is determined through fiber-optic network and software design. The OIS provides an on-demand method for obtaining acceptable inventory reports while eliminating the need for human presence inside the material storage facility. By using modularization and prefabricated construction with mature technologies and components, an OIS installation with virtually unlimited capacity can be tailored to the customer's requirements

Preparation and use of polymeric materials containing hydrophobic anions and plasticizers for separation of cesium and strontium

International Nuclear Information System (INIS)

Abney, K.D.; Kinkead, S.A.; Mason, C.F.V.; Rais, J.

1997-01-01

Preparation and use is described for polymeric materials containing hydrophobic anions and plasticizers for extraction of cesium and strontium. The use of polymeric materials containing plasticizers which are solvents for hydrophobic anions such as derivatives of cobalt dicarbollide or tetraphenylborate which are capable of extracting cesium and strontium ions from aqueous solutions in contact with the polymeric materials, is described. The polymeric material may also include a synergistic agent for a given ion like polyethylene glycol or a crown ether, for removal of radioactive isotopes of cesium and strontium from solutions of diverse composition and, in particular, for solutions containing large excess of sodium nitrate

Inherent N,O-containing carbon frameworks as electrode materials for high-performance supercapacitors.

Science.gov (United States)

Hu, Fangyuan; Wang, Jinyan; Hu, Shui; Li, Linfei; Wang, Gang; Qiu, Jieshan; Jian, Xigao

2016-09-15

N,O-Containing micropore-dominated materials have been developed successfully via temperature-dependent cross-linking of 4,4'-(dioxo-diphenyl-2,3,6,7-tetraazaanthracenediyl)dibenzonitrile (DPDN) monomers. By employing a molecular engineering strategy, we have designed and synthesized a series of porous heteroatom-containing carbon frameworks (PHCFs), in which nitrogen and oxygen heteroatoms are distributed homogeneously throughout the whole framework at the atomic level, which can ensure the stability of its electrical properties. The as-made PHCFs@550 exhibits a high specific capacitance of 378 F g -1 , with an excellent long cycling life, including excellent cycling stability (capacitance retention of ca. 120% over 20 000 cycles). Moreover, the successful preparation of PHCFs provides new insights for the fabrication of nitrogen and oxygen-containing electrode materials from readily available components via a facile route.

Comparative study of the more promising combinations of blanket materials, power conversion systems, and tritium recovery and containment systems for fusion reactors

International Nuclear Information System (INIS)

Fraas, A.P.

1975-11-01

The many possible combinations of blanket materials, tritium generation and recovery systems, and power conversion systems were surveyed first by reviewing the principal design studies that have been prepared and then by examining a comprehensive set of designs generated by using a common set of ground rules that included all of the boundary conditions that could be envisioned. The results indicate that, of the wide variety of systems that have been considered, by far the most promising employs lithium recirculated in a closed loop within a niobium blanket structure and cooled with boiling potassium or cesium. This approach gives the simplest and lowest cost tritium recovery system, the lowest pressure and thermal stresses, the simplest structure with the lowest probability of a leak, the greatest resistance to damage from a plasma energy dump, and the lowest rate of plasma contamination by either outgassing or sputtering. The only other blanket materials combination that appears fairly likely to give a satisfactory tritium generation and recovery system is an Li 2 BeF 4 -Incoloy blanket, and even this system involves major uncertainties in the effectiveness, size, and cost of the tritium recovery system. Further, the Li 2 BeF 4 blanket system has the disadvantage that the world reserves of beryllium are too limited to support a full-blown fusion reactor economy, its poor thermal conductivity leads to cooling difficulties and a requirement for a complex structure with intricate cooling passages, and this inherently leads to an expensive blanket with a relatively high probability of leaks. The other blanket materials combinations yield even less attractive systems

A new classification system for all-ceramic and ceramic-like restorative materials.

Science.gov (United States)

Gracis, Stefano; Thompson, Van P; Ferencz, Jonathan L; Silva, Nelson R F A; Bonfante, Estevam A

2015-01-01

Classification systems for all-ceramic materials are useful for communication and educational purposes and warrant continuous revisions and updates to incorporate new materials. This article proposes a classification system for ceramic and ceramic-like restorative materials in an attempt to systematize and include a new class of materials. This new classification system categorizes ceramic restorative materials into three families: (1) glass-matrix ceramics, (2) polycrystalline ceramics, and (3) resin-matrix ceramics. Subfamilies are described in each group along with their composition, allowing for newly developed materials to be placed into the already existing main families. The criteria used to differentiate ceramic materials are based on the phase or phases present in their chemical composition. Thus, an all-ceramic material is classified according to whether a glass-matrix phase is present (glass-matrix ceramics) or absent (polycrystalline ceramics) or whether the material contains an organic matrix highly filled with ceramic particles (resin-matrix ceramics). Also presented are the manufacturers' clinical indications for the different materials and an overview of the different fabrication methods and whether they are used as framework materials or monolithic solutions. Current developments in ceramic materials not yet available to the dental market are discussed.

Code for calculation of spreading of radioactivity in reactor containment systems

International Nuclear Information System (INIS)

Vertes, P.

1992-09-01

A detailed description of the new version of TIBSO code is given, with applications for accident analysis in a reactor containment system. The TIBSO code can follow the nuclear transition and the spatial migration of radioactive materials. The modelling of such processes is established in a very flexible way enabling the user to investigate a wide range of problems. The TIBSO code system is described in detail, taking into account the new developments since 1983. Most changes improve the capabilities of the code. The new version of TIBSO system is written in FORTRAN-77 and can be operated both under VAX VMS and PC DOS. (author) 5 refs.; 3 figs.; 21 tabs

Port Security: Container Cargo Control

Directory of Open Access Journals (Sweden)

Vladivoj Vlaković

2006-05-01

Full Text Available illicittrafficking of threat materials, especially explosives, chemicalsubstances and radioactive or nuclear material. The transportof the threat materials by using sea routes is an advantageto te"orists especially because of the possible use of ship containers.The container is the basis of world trade. It is assumed thatthe world total movement in containers is about 200 millionTEUs ("20-foot equivalent units" per year. The list of materialstransported by containers which should be subject to inspectionwith the aim of reducing the acts of te"orism includes explosives,narcotics, chemical weapons, hazardous chemicalsand radioactive materials.Of special interest is nuclear te"orism. The risk of nuclearte"orism carried out by sub-national groups should be considerednot only in the construction and/or use of nuclear device,but also in possible radioactive contamination of large urbanareas.The system of ship containers control is an essential componentof «smart border» concept. Modem personnel, parcel,vehicle and cargo inspection systems are non-invasive imagingtechniques based on the use of nuclear analytical techniques.The inspection systems use penetrating radiations: hard x-rays(300 keV or more or gamma-rays from radioactive sources(137Cs and 60Co with energies from 600 to 1300 keV that producea high resolution radiograph of the load. Unfortunately,this information is "non-specific" in that it gives no informationon the nature of objects that do not match_ the travel documentsand are not recognized by a visual analysis of the radiographicpicture. Moreover, there are regions of the containerwherex and gamma-ray systems are "blind" due to the high averageatomic number of the objects i"adiated that appear asblack spots in the radiographic image.The systems being developed are based on the use of fast, 14Me V, neutrons with detection of associated a-particle from nuclearreactionbywhichneutrons are produced (d+t>a+n.Jnsuch a way the possibility to

Advanced containment research for the Canadian Nuclear Fuel Waste Management Program

International Nuclear Information System (INIS)

Onofrei, M.; Mathew, P.M.; McKay, P.; Hosaluk, L.J.; Oscarson, D.W.

1986-09-01

This document outlines the program on the development of advanced containment systems for the disposal of used fuel in a vault deep in plutonic rock. Possible advanced containment concepts, the strategy adopted in selecting potential container materials, and experimental programs currently underway or planned are presented. Most effort is currently directed toward developing long-term containment systems based on non-metallic materials and massive metal containers. The use of additional independent barriers to extend the lifetime of simple containment systems is also being evaluated. 58 refs

VEDS-Automated system for inspection of vehicles and containers for explosives and other threats

International Nuclear Information System (INIS)

Gozani, T.; Liu, F.; Sivakumar, M.

2004-01-01

Many parts of national infrastructures around the world are very vulnerable to terrorist threats in the form of large vehicle bombs. The larger bomb, the larger is the damage and its extent. The number of containers and vehicles crossing land or sea ports of entry is huge. Tough the probability is low, any vehicle may contain a threat. Any system addressing these enormous security tasks should obviously be based on excellent human intelligence to focus the attention on a much smaller number of high-risk containers and vehicles. These containers must then be subjected to a thorough and reliable inspection for the threats.Viable security system must incorporate a credible and effective inspection to achieve its purposes. It should have high performance and be operationally acceptable. This means the system must possess high detection capabilities, low false positive rate, fast response and provide automatic decision eliminating the need for human interpretation. Ancore has developed a range of new inspection devices, which are highly suitable for the above tasks. All the systems are automatic, material specific, high performance for a wide range and type of threats. Some of them are also highly modular, and compact. Some of the systems are fixed, other are relocatable, or fully mobile. The presentation will discuss Ancore's VEDS (Vehicle Explosive Detection System) which detects bulk explosives (expandable also to radiological and nuclear threats)) in marine containers, trucks and cars. The compact and rugged nature of the VEDS sensor makes it suitable for many forms of conveyance: mobile (van mounted), portal, forklift mounted, or mounted on container unloading rig. The physics principles of the system and some recent applications and results will be presented

Hazardous-materials-management system: a guide for local emergency managers

International Nuclear Information System (INIS)

Lee, M.T.; Roe, P.G.

1981-07-01

An increase in the manufacture, storage, and transportation of hazardous materials is occurring across the nation. Local jurisdictions have realized that they have the responsibility to assure a reasonable level of safety to their community members and visitors alike. Such a responsibility can be met by developing methods of preventing hazardous materials incidents; enforcing laws related to transporting and storing hazardous materials; the initiating of an appropriate first response, and activating available resources of government agencies and commercial organizations that deal with containment and cleanup. This manual has been written to help in the development of a total Hazardous Material Management System. The manual describes one approach but allows for variations as may be appropriate for the specific jurisdiction

Fabricating Composite-Material Structures Containing SMA Ribbons

Science.gov (United States)

Turner, Travis L.; Cano, Roberto J.; Lach, Cynthia L.

2003-01-01

An improved method of designing and fabricating laminated composite-material (matrix/fiber) structures containing embedded shape-memory-alloy (SMA) actuators has been devised. Structures made by this method have repeatable, predictable properties, and fabrication processes can readily be automated. Such structures, denoted as shape-memory-alloy hybrid composite (SMAHC) structures, have been investigated for their potential to satisfy requirements to control the shapes or thermoelastic responses of themselves or of other structures into which they might be incorporated, or to control noise and vibrations. Much of the prior work on SMAHC structures has involved the use SMA wires embedded within matrices or within sleeves through parent structures. The disadvantages of using SMA wires as the embedded actuators include (1) complexity of fabrication procedures because of the relatively large numbers of actuators usually needed; (2) sensitivity to actuator/ matrix interface flaws because voids can be of significant size, relative to wires; (3) relatively high rates of breakage of actuators during curing of matrix materials because of sensitivity to stress concentrations at mechanical restraints; and (4) difficulty of achieving desirable overall volume fractions of SMA wires when trying to optimize the integration of the wires by placing them in selected layers only.

Liquid filter for liquids containing radioactive materials

International Nuclear Information System (INIS)

Rohleder, N.; Schwarz, F.

1986-01-01

A device for filtering radioactive liquids loaded with solids is described, which has a pressure-resistant housing with a lid and an incomer for the turbid liquid and a collecting space and drain for the filtrate at the bottom of the housing. A filter cartridge is present in this housing. Such a filtering device must be suitable for use in nuclear plants, must be easy to replace by remote control and must minimise the carrying over of radioactive particles. This problem should be solved by the filter cartridge consisting of a large number of horizontal filter plates stacked above one another, which carry a deep layer filter material acting in the sub-micron range. The turbid liquid runs into the centre of the stack of filter plates via a vertical central duct. The intermediate spaces between the filter places are connected to this central duct via the layer of filter material. The filter plates are sealed against one another on the outer circumference and have radial drain openings for the filtrate on the outside. The central duct is sealed at the lower end by a plate. When the filter cartridge is replaced, the radioactive waste in the filter cartridge remains safely enclosed and can be conditioned in suitable containers. (orig.) [de

Corrosion of container and infrastructure materials under clay repository conditions

International Nuclear Information System (INIS)

Debruyn, W.; Dresselaers, J.; Vermeiren, P.; Kelchtermans, J.; Tas, H.

1991-01-01

With regard to the disposal of high-level radioactive waste, it was recommended in a IAEA Technical Committee meeting to perform tests in realistic environments corresponding with normal and accidental conditions, to qualify and apply corrosion monitoring techniques for corrosion evaluation under real repository conditions and to develop corrosion and near-field evolution models. The actual Belgian experimental programme for the qualification of a container for long-term HLW storage in clay formations complies with these recommendations. The emphasis in the programme is indeed on in situ corrosion testing and monitoring and on in situ control of the near-field chemistry. Initial field experiments were performed in a near-surface clay quarry at Terhaegen. Based on a broad laboratory material screening programme and in agreement with the Commission of the European Communities, three reference materials were chosen for extensive in situ overpack testing. Ti/0.2 Pd and Hastelloy C-4 were chosen as reference corrosion resistant materials and a low-carbon steel as corrosion allowance reference material. This report summarizes progress made in the material qualification programme since the CEC contract of 1983-84. 57 Figs.; 15 Tabs.; 18 Refs

Establishment of ultra trace nuclear material analysis system

International Nuclear Information System (INIS)

Song, Kyuseok; Jee, Kwangyong; Lee, Changheon

2012-05-01

Highly accurate and precise analysis of ultra trace nuclear materials contained in swipe samples and environmental samples is required to improve the national nuclear transparency and the international nuclear security. The objectives of the first stage of this project are to develop the techniques for bulk analysis of environmental samples and the elemental techniques for particle analysis using FT-TIMS. To accomplish the objectives, state-of-the-art analytical instruments were set up followed by the development of the techniques for screening of nuclear materials, chemical treatement, particle handling, isotopic measurements using TIMS and ICP-MS, and fabrication of uranium microparticles. The verifications of the developed techniques were carried out by measurement of reference materials, and by participation to interlaboratory comparison programs. In additon, the establishement of a quality management system and the performance of the analysis of QC samples for IAEA-NWAL qualification were carried out to obtain the international accreditation for the related analytical system. In this report, the results of research and developments, and the achievements to obtain the international accreditation were summarized

THE NEED FOR A NEW JOINING TECHNOLOGY FOR THE CLOSURE WELDING OF RADIOACTIVE MATERIALS CONTAINERS

International Nuclear Information System (INIS)

CANNELL GR; HILL BE; GRANT GJ

2008-01-01

One of the activities associated with cleanup throughout the Department of Energy (DOE) complex is packaging radioactive materials into storage containers. Much of this work will be performed in high-radiation environments requiring fully remote operations, for which existing, proven systems do not currently exist. These conditions demand a process that is capable of producing acceptable (defect-free) welds on a consistent basis; the need to perform weld repair, under fully-remote operations, can be extremely costly and time consuming. Current closure welding technology (fusion welding) is not well suited for this application and will present risk to cleanup cost and schedule. To address this risk, Fluor and the Pacific Northwest National Laboratory (PNNL), are proposing that a new and emerging joining technology, Friction Stir Welding (FSW), be considered for this work. FSW technology has been demonstrated in other industries (aerospace and marine) to produce near flaw-free welds on a consistent basis. FSW is judged capable of providing the needed performance for fully-remote closure welding of containers for radioactive materials for the following reasons: FSW is a solid-state process; material is not melted. As such, FSW does not produce the type of defects associated with fusion welding, e.g., solidification-induced porosity, cracking, distortion due to weld shrinkage, and residual stress. In addition, because FSW is a low-heat input process, material properties (mechanical, corrosion and environmental) are preserved and not degraded as can occur with 'high-heat' fusion welding processes. When compared to fusion processes, FSW produces extremely high weld quality. FSW is performed using machine-tool technology. The equipment is simple and robust and well-suited for high radiation, fully-remote operations compared to the relatively complex equipment associated with the fusion-welding processes. Additionally, for standard wall thicknesses of radioactive materials

Structure, production and properties of high-melting compounds and systems (hard materials and hard metals)

International Nuclear Information System (INIS)

Holleck, H.; Thuemmler, F.

1979-07-01

The report contains contributions by various authors to the research project on the production, structure, and physical properties of high-melting compounds and systems (hard metals and hard materials), in particular WC-, TaC-, and MoC-base materials. (GSCH) [de

An assessment of Class-9 (core-melt) accidents for PWR dry-containment systems

International Nuclear Information System (INIS)

Theofanous, T.G.; Saito, M.

1981-01-01

The phenomenology of core-melt accidents in dry containments was examined for the purpose of identifying the margins of safety in such Class-9 situations. The scale (geometry) effects appear to crucially limit the extent (severity) of steam explosions. This together with the established reduced explosivity of the corium-A/water system, and the inherently high capability of dry containments (redinforced concrete, and shields in some cases, seismic design etc.) lead to the conclusion that failure due to steam explosions may be considered essentially incredible. These premixture scaling considerations also impact ultimate debris disposition and coolability and need additional development. A water-flooded reactor cavity would have beneficial effects in limiting (but not necessarily eliminating) melt-concrete interactions. Independently of the initial degree of quenching and/or scale of fragmentation, mechanisms exist that drive the system towards ultimate stability (coolability). Additional studies, with intermediate-scale prototypic materials are recommended to better explore these mechanisms. Containment heat removal systems must provide the crucial capability of mitigating such accidents. Passive systems should be explored and assessed against currently available and/or improved active systems taking into account the rather loose time constraints required for activation. It appears that containment margins for accommodating the hydrogen problem are limited. This problem appears to stand out not only in terms of potential consequences but also in terms of lack of any readily available and clear cut solutions at this time. (orig.)

Sharps container

Science.gov (United States)

Lee, Angelene M. (Inventor)

1992-01-01

This invention relates to a system for use in disposing of potentially hazardous items and more particularly a Sharps receptacle for used hypodermic needles and the like. A Sharps container is constructed from lightweight alodined nonmagnetic metal material with a cup member having an elongated tapered shape and length greater than its transverse dimensions. A magnet in the cup member provides for metal retention in the container. A nonmagnetic lid member has an opening and spring biased closure flap member. The flap member is constructed from stainless steel. A Velcro patch on the container permits selective attachment at desired locations.

Martensitic/ferritic steels as container materials for liquid mercury target of ESS

International Nuclear Information System (INIS)

Dai, Y.

1996-01-01

In the previous report, the suitability of steels as the ESS liquid mercury target container material was discussed on the basis of the existing database on conventional austenitic and martensitic/ferritic steels, especially on their representatives, solution annealed 316 stainless steel (SA 316) and Sandvik HT-9 martensitic steel (HT-9). Compared to solution annealed austenitic stainless steels, martensitic/ferritic steels have superior properties in terms of strength, thermal conductivity, thermal expansion, mercury corrosion resistance, void swelling and irradiation creep resistance. The main limitation for conventional martensitic/ferritic steels (CMFS) is embrittlement after low temperature (≤380 degrees C) irradiation. The ductile-brittle transition temperature (DBTT) can increase as much as 250 to 300 degrees C and the upper-shelf energy (USE), at the same time, reduce more than 50%. This makes the application temperature range of CMFS is likely between 300 degrees C to 500 degrees C. For the present target design concept, the temperature at the container will be likely controlled in a temperature range between 180 degrees C to 330 degrees C. Hence, CMFS seem to be difficult to apply. However, solution annealed austenitic stainless steels are also difficult to apply as the maximum stress level at the container will be higher than the design stress. The solution to the problem is very likely to use advanced low-activation martensitic/ferritic steels (LAMS) developed by the fusion materials community though the present database on the materials is still very limited

Thermodynamics of a natural draught-cooled container deposit for radioactive materials

International Nuclear Information System (INIS)

Schoenfeld, R.; Dorst, H.J.

1982-01-01

This article interprets a calculation model for the determination of heat dissipation and temperature distribution of cooling air within an intermediate container deposit cooled with air by natural draught for self-heating materials. The mathematical modelling of the physical processes in the flowing medium 'air' takes place stationarily and one-dimensionelly in flow direction. The calculation model is based on known procedures for the convective heat transmission, for the description of channel flow, and for the determination of pressure losses. It provides the thermodynamic characteristic data which are required for an engineering and safety design of a container deposit. (orig.) [de

CTL Industries simplifies mining processes : fill containment system a simple solution for backfilling stopes

Energy Technology Data Exchange (ETDEWEB)

Larmour, A.

2010-12-01

Several large mining companies are interested in a patent-pending fill containment system designed to replace shotcrete fences after a stope has been filled. The existing process is extremely labour and material intensive. This article discussed how the new system has made work easier, safer and increased the bottom line. The article described the design and specifications of the shotcrete containment system. The advantages of the system include no wait time for customers for shotcrete teams to build fences, and it is a quick, easy process that takes about 3 hours to set up, inflate and fill. The article also outlined a shaft guide electronic profiling mechanism that had been developed to complement the shaft guide laminating device. The product electronically measures shaft guides in mine shafts to determine how much wear has occurred on the timber. Last, the article described a refuge station door sealant kit with a cabinet that contains items required to seal the refuge station door should an emergency occur. This quick and easy system replaces the previous method in which clay slugs are soaked in a five-gallon pail of water and applied by hand. 1 ref., 1 fig.

10 CFR 32.74 - Manufacture and distribution of sources or devices containing byproduct material for medical use.

Science.gov (United States)

2010-01-01

... 10 Energy 1 2010-01-01 2010-01-01 false Manufacture and distribution of sources or devices... SPECIFIC DOMESTIC LICENSES TO MANUFACTURE OR TRANSFER CERTAIN ITEMS CONTAINING BYPRODUCT MATERIAL Generally Licensed Items § 32.74 Manufacture and distribution of sources or devices containing byproduct material for...

Mathematical structure of ocean container transport systems; Kaiyo container yuso system no suriteki kozo ni tsuite

Energy Technology Data Exchange (ETDEWEB)

Shinkai, A [Kyushu University, Fukuoka (Japan). Faculty of Engineering; Chikushi, Y [Nippon Telegraph and Telephone Corp., Tokyo (Japan)

1997-10-01

Mathematical structure of a vessel arrangement program was discussed in order to learn roles of container ships in ocean transport systems among China, NIES/ASEAN countries and Japan. Formulation is possible on a mathematical handling method for sailing route connection diagrams between ports, a transport network to indicate container movements, a service network to indicate sailing routes, and a network generalizing them. This paper describes an analysis made on the container transport system between Japan and China, taken as an example. Four ports were selected each from Japan and China, and the statistical database for fiscals 1996 and 1994 was utilized to set models for: (a) the liner network system with transshipment at the port of Shanghai and (b) the cruising route system going through the ports of Yokohama, Nagoya and Kobe. A hypothesis was set that a consortium (coordinated ship allocation) can be implemented ideally and completely. The transport network (a) is lower by 10% in total cost than the transport network (b), resulting in 1.6 times greater productivity. Actual service network is closer to the network (b), but the system can be utilized for discussing guidelines on vessel arrangement programs with which shipping companies pursue better management efficiency under a condition that the consortium can be formed. 10 refs., 6 figs., 2 tabs.

Container code recognition in information auto collection system of container inspection

International Nuclear Information System (INIS)

Su Jianping; Chen Zhiqiang; Zhang Li; Gao Wenhuan; Kang Kejun

2003-01-01

Now custom needs electrical application and automatic detection. Container inspection should not only give the image of the goods, but also auto-attain container's code and weight. Its function and track control, information transfer make up the Information Auto Collection system of Container Inspection. Code Recognition is the point. The article is based on model match, the close property of character, and uses it to recognize. Base on checkout rule, design the adjustment arithmetic, form the whole recognition strategy. This strategy can achieve high recognition ratio and robust property

Materials compatibility issues related to thermal energy storage for a space solar dynamic power system

Science.gov (United States)

Faget, N. M.

1986-01-01

Attention is given to results obtained to date in developmental investigations of a thermal energy storage (TES) system for the projected NASA Space Station's solar dynamic power system; these tests have concentrated on issues related to materials compatibility for phase change materials (PCMs) and their containment vessels' materials. The five PCMs tested have melting temperatures that correspond to the operating temperatures of either the Brayton or Rankine heat engines, which were independently chosen for their high energy densities.

Design of double containment canister cask storage system

International Nuclear Information System (INIS)

Asami, M.; Matsumoto, T.; Oohama, T.; Kuriyama, K.; Kawakami, K.

2004-01-01

Spent fuels discharged from Japanese LWR will be stored as recycled-fuel-resources in interim storage facilities. The concrete cask storage system is one of important forms for the spent fuel interim storage. In Japan, the interim storage facility will be located near the coast, therefore it is important to prevent SCC (Stress Corrosion Cracking) caused by sea salt particles and to assure the containment integrity of the canister which contains spent fuels. KEPCO, NFT and OCL have designed the double containment canister cask storage system that can assure the long-term containment integrity and monitor the containment performance without storage capacity decrease. Major features of the combined canister cask system are shown as follows: This system can survey containment integrity of dual canisters by monitoring the pressure of the gap between canisters. The primary canister has dual lids sealed by welding. The secondary canister has single lid tightened by bolts and sealed by metallic gaskets. The primary canister is contained in the transport cask during transportation, and the gap between the primary canister and the transport cask is filled with He gas. Under storage condition in the concrete cask, the primary canister is contained in the secondary canister, and the gap between these canisters is filled with helium gas. Hence this system can prevent the primary canister to contact sea salt particle in the air and from SCC. Decrease of cooling performance because of the double canister is compensated by fins fitted on the secondary canister surface. Then, this system can prevent the decrease of storage capacity determined by the fuel temperature limit. This system can assure that the primary canister will keep intact for long term storage. Therefore, in the case of pressure down of the gap between canisters, it can be considered that the secondary canister containment is damaged, and the primary canister will be transferred to another secondary canister at the

Application of the ASME code in designing containment vessels for packages used to transport radioactive materials

International Nuclear Information System (INIS)

Raske, D.T.; Wang, Z.

1992-01-01

The primary concern governing the design of shipping packages containing radioactive materials is public safety during transport. When these shipments are within the regulatory jurisdiction of the US Department of Energy, the recommended design criterion for the primary containment vessel is either Section III or Section VIII, Division 1, of the ASME Boiler and Pressure Vessel Code, depending on the activity of the contents. The objective of this paper is to discuss the design of a prototypic containment vessel representative of a packaging for the transport of high-level radioactive material

Possibilities of using new technology materials in constructing the radioactive waste containers The paper will consider using the latest technologies in material science for building

International Nuclear Information System (INIS)

Itu, Razvan Bogdan

2008-01-01

The paper will consider using the latest technologies in materials science for building the radioactive waste containers. A new amorphous steel has been discovered by the scientists from the University of Virginia, a material three times stronger then conventional steel and non-magnetic. Scientists shown that this steel, DARVA - Glass 101, has superior anticorrosive proprieties. The paper will also consider using Para-Aramides in protecting the radioactive waste containers. Chemical and physical properties of these materials shown a great tensile strength and the inter-chain bonds make these materials extremely strong. (author)

Evaluation of copper, aluminum bronze, and copper-nickel container material for the Yucca mountain project

International Nuclear Information System (INIS)

Kass, J.

1990-01-01

Copper, 70 percent aluminum bronze, and 70/30 copper-nickel were evaluated as potential waste-packaging materials as part of the Yucca Mountain Project. The proposed waste repository site is under a desert mountain in southern Nevada. The expected temperatures at the container surface are higher than at other sites, about 250C at the beginning of the containment period; they could fall below the boiling point of water during this period, but will be exposed to very little water, probably less than 5 l/a. Initial gamma flux will be 10 4 rad/h, and no significant hydrostatic or lithostatic pressure is expected. Packages will contain PWR or BWR fuel, or processed-glass waste. Three copper alloys are being considered for containers: oxygen-free copper (CDA 102); 7 percent aluminum bronze (CDA 613); and 70/30 copper-nickel (CDA 715). Phase separation due to prolonged thermal exposure could be a problem for the two alloys, causing embrittlement. The reduction of internal oxides present in pure copper by hydrogen could cause mechanical degradation. Corrosion and oxidation rates measured for the three materials in well water with and without gamma irradiation at flux rates about ten times higher than those expected were all quite small. The corrosion/oxidation rates for CDA715 show a marked increase under irradiation, but are still acceptable. In the presence of ammonia and other nitrogen-bearing species stress corrosion cracking (SCC) is a concern. Welded U-bend specimens of all three materials have been tested for up to 10000 h in highly irradiated environments, showing no SCC. There was some alloy segregation in the Al bronze specimens. The investigators believe that corrosion and mechanical properties will not present problems for these materials at this site. Further work is needed in the areas of weld inspection, welding techniques, embrittlement of weld metal, the effects of dropping the containers during emplacement, and stress corrosion cracking. Other materials

ERG review of waste package container materials selection and corrosion

International Nuclear Information System (INIS)

Moak, D.P.; Perrin, J.S.

1986-07-01

The Engineering Review Group (ERG) was established by the Office of Nuclear Waste Isolation (ONWI) to help evaluate engineering-related issues in the US Department of Energy's nuclear waste repository program. The October 1984 meeting of the ERG reviewed the waste package container materials selection and corrosion. This report documents the ERG's comments and recommendations on these subjects and the ONWI response to the specific points raised by the ERG

46 CFR 56.50-60 - Systems containing oil.

Science.gov (United States)

2010-10-01

... 46 Shipping 2 2010-10-01 2010-10-01 false Systems containing oil. 56.50-60 Section 56.50-60... APPURTENANCES Design Requirements Pertaining to Specific Systems § 56.50-60 Systems containing oil. (a)(1) Oil-piping systems for the transfer or discharge of cargo or fuel oil must be separate from other piping...

The first word in material control is material

International Nuclear Information System (INIS)

Martin, H.R.; Wilkey, D.D.

1989-01-01

Material control has tended to rely on containment and access control, augmented by physical inventories, to meet the material control and accounting (MC ampersand A) goals of detecting theft/diversion and providing assurance that all nuclear material (NM) is present. Such systems have significant deficiencies. Material containment strategies are generally based on protection provided at boundaries around the NM and rely on alarms at the boundary for detection of theft/diversion. Assurance that all NM is present requires a negative inference based on the absence of alarms. Additionally, design of effective boundary protection systems requires that the designer be able to anticipate and provide protection for all scenarios that the insider adversary might utilize in removing material from the facility. Access control is an administrative system that cannot protect against malevolent actions by insiders authorized to access the material. Inventories may not provide timely detection of theft/diversion, and the sensitivity of detection depends on the magnitude of the variance of the inventory difference. More effective material control is provided for both material in storage and in process by a material-oriented system designed to detect abnormal events involving NM. Abnormal events are defined as any unauthorized activity involving NM, whether accidental or deliberate, and are assessed to determine the cause of the discrepancy. The designs of material-oriented control systems vary greatly, depending on the operations involved; however, a model system would include the use of process monitoring data for material control and automated surveillance of material in storage

Process for surface treatment of zirconium-containing cladding materials for fuel element or other components for nuclear reactors

International Nuclear Information System (INIS)

Videm, K.G.; Lunde, L.R.; Kooyman, H.H.

1975-01-01

A process for the surface treatment of zirconium-base cladding materials for fuel elements or other components for nuclear reactors is described. The treatment includes pickling the cladding material in a fluoride-containing bath, and then applying a protective coating through oxidation to the pickled cladding material. The fluoride-containing contaminants which remain on the surface of the cladding material during pickling are removed or rendered harmless by anodic oxidation

Time, temperature, chemical and radiation exposure effects on the mechanical performance of polymeric materials used for the containment of radioactive waste. Abstract 56

International Nuclear Information System (INIS)

Brown, L.; Bui, V.T.; Bonin, H.W.

2004-01-01

'Full text:' The mechanical performance of materials used for the fabrication of materials used for the fabrication of a storage container for radioactive waste is dependent on the environment to which the container will be exposed over its lifetime. There exists a complex relationship between the many variables affecting the properties of the polymer and potentially decreasing the mechanical performance properties of the container. To further complicate the system, the degradation processes are often time dependant. Experimental results for Nylon 6,6, Semi-Aromatic Nylon, and Polycarbonate have been used as a basis for the development of a model, which represents the performance of a polymeric container used for the storage of radioactive waste over time. The experimental work aimed at providing information on the materials performance in a variety of environmental conditions, as well as a function of time. This included exposing the polymeric material samples to a mixed field of radiation in the SLOWPOKE-2 nuclear reactor. A series of dilution viscometry experiments have been used to relate the changes in mechanical performance to changes in the physical characteristics of the polymer molecules. This provided a valuable tool in the extrapolation of the model to other polymeric materials, and allowed for use of the model based on theoretical predictions of a polymer molecules reaction to various environmental conditions. (author)

Time, temperature, chemical and radiation exposure effects on the mechanical performance of polymeric materials used for the containment of radioactive waste. Abstract 56

Energy Technology Data Exchange (ETDEWEB)

Brown, L.; Bui, V.T.; Bonin, H.W. [Royal Military College of Canada, Dept. of Chemistry and Chemical Engineering, Kingston, Ontario (Canada)]. E-mail: Laura-lee.Brown@rmc.ca; bui-v@rmc.ca; bonin-h@rmc.ca

2004-07-01

'Full text:' The mechanical performance of materials used for the fabrication of materials used for the fabrication of a storage container for radioactive waste is dependent on the environment to which the container will be exposed over its lifetime. There exists a complex relationship between the many variables affecting the properties of the polymer and potentially decreasing the mechanical performance properties of the container. To further complicate the system, the degradation processes are often time dependant. Experimental results for Nylon 6,6, Semi-Aromatic Nylon, and Polycarbonate have been used as a basis for the development of a model, which represents the performance of a polymeric container used for the storage of radioactive waste over time. The experimental work aimed at providing information on the materials performance in a variety of environmental conditions, as well as a function of time. This included exposing the polymeric material samples to a mixed field of radiation in the SLOWPOKE-2 nuclear reactor. A series of dilution viscometry experiments have been used to relate the changes in mechanical performance to changes in the physical characteristics of the polymer molecules. This provided a valuable tool in the extrapolation of the model to other polymeric materials, and allowed for use of the model based on theoretical predictions of a polymer molecules reaction to various environmental conditions. (author)

Graphic-object information system {open_quotes}research base for reactor materials science{close_quotes}

Energy Technology Data Exchange (ETDEWEB)

Markina, N.V.; Lebedeva, E.E.; Arkhangel`skii, N.V.; Semenov, S.B.; Moiseev, A.L.

1994-11-01

An information system developed for reactor materials research is described. The information system incorporates an expert system, MATREKS, and a heirarchial data base. The data base contains information from 20 Russian research reactors. The information system structure, data base structure, search methods, system output modes, and technical facilities and software required are briefly discussed. 6 refs., 2 figs.

Improved process for producing a fermentation product from a lignocellulose-containing material

DEFF Research Database (Denmark)

2017-01-01

The present invention relates to the production of hydrolyzates from a lignocellulose-containing material, and to fermentation of the hydrolyzates. More specifically, the present invention relates to the detoxification of phenolic inhibitors and toxins formed during the processing of lignocellulose...

A process for producing a fermentation product from a lignocellulose-containing material

DEFF Research Database (Denmark)

2016-01-01

The present invention relates to the production of hydrolyzates from a lignocellulose-containing material, and to fermentation of the hydrolyzates. More specifically, the present invention relates to the detoxification of phenolic inhibitors and toxins formed during the processing of lignocellulose...

Safety analysis report: packages. Argonne National Laboratory SLSF test train shipping container, P-1 shipment. Fissile material. Final report

International Nuclear Information System (INIS)

Meyer, C.A.

1975-06-01

The package is used to ship an instrumented test fuel bundle (test train) containing fissile material. The package assembly is Argonne National Laboratory (ANL) Model R1010-0032. The shipment is fissile class III. The packaging consists of an outer carbon steel container into which an inner container is placed; the inner container is separated from the outer container by urethane foam cushioning material. The test train is supported in the inner container by a series of transverse supports spaced along the length of the test train. Both the inner and outer containers are closed with bolted covers. The covers do not seal the containers in a leaktight manner. The gross weight of the shipment is about 8350 lb. The unirradiated fissile material content is less than 3 kg of UO 2 of up to 93.2 percent enrichment. This is a Type A quantity (transport group III and less than 3 curies) of radioactive material which does not require shielding, cooling or heating, or neutron absorption or moderation functions in its packaging. The maximum exterior dimensions of the container are 37 ft 11 in. long, 24 1 / 2 in. wide, and 19 3 / 4 in. high

Interaction of tellurium and tellurium-containing semiconductor compounds with solutions of HI-HNO3-H2O system

International Nuclear Information System (INIS)

Tomashik, V.N.; Sava, A.A.; Tomashik, Z.F.

1994-01-01

As a result of experimental investigations and physical-chemical simulation are established regularities of solution of semiconducting tellurium-containing compounds in HI-HNO 3 -H 2 O systems. In HNO 3 -HI system solutions enriched by HNO 3 are not used for CdTe treatment but HI enriched solution are similar in composition with I 2 -HI solutions. Solution of the given tellurium-containing materials proceeds by a chemical mechanism and is determined by tellurium oxidation with iodine

Evaluation of Neutron Poison Materials for DOE SNF Disposal Systems

International Nuclear Information System (INIS)

Vinson, D.W.; Caskey, G.R. Jr.; Sindelar, R.L.

1998-09-01

Aluminum-based spent nuclear fuel (Al-SNF) from foreign and domestic research reactors is being consolidated at the Savannah River Site (SRS) for ultimate disposal in the Mined Geologic Disposal System (MGDS). Most of the aluminum-based fuel material contains highly enriched uranium (HEU) (more than 20 percent 235U), which challenges the preclusion of criticality events for disposal periods exceeding 10,000 years. Recent criticality analyses have shown that the addition of neutron absorbing materials (poisons) is needed in waste packages containing DOE SNF canisters fully loaded with Al-SNF under flooded and degraded configurations to demonstrate compliance with the requirement that Keff less than 0.95. Compatibility of poison matrix materials and the Al-SNF, including their relative degradation rate and solubility, are important to maintain criticality control. An assessment of the viability of poison and matrix materials has been conducted, and an experimental corrosion program has been initiated to provide data on degradation rates of poison and matrix materials and Al-SNF materials under repository relevant vapor and aqueous environments. Initial testing includes Al6061, Type 316L stainless steel, and A516Gr55 in synthesized J-13 water vapor at 50 degrees C, 100 degrees C, and 200 degrees C and in condensate water vapor at 100 degrees C. Preliminary results are presented herein

Proportioning equipment for vibration filling and compacting of grain materials in pipe containers, especially of fuel elements

International Nuclear Information System (INIS)

Pinkas, V.; Filip, Z.; Beranek, J.

1981-01-01

The equipment consists of a base plate to which are attached the fastening collar fo the pipe container and the guide column with the height-adjustable support. The filling pipe is fixed to the support. The proportioning equipment prevents particles of grain material from segregation, thus allowing to achieve homogeneity of the material in the whole volume to be compacted. It also allows determining the height of the column of material in the pipe container without destructive effects on the stacked material. The equipment is designed for the manufacture of shortened fuel elements. (J.B.)

Type I Collagen and Strontium-Containing Mesoporous Glass Particles as Hybrid Material for 3D Printing of Bone-Like Materials.

Science.gov (United States)

Montalbano, Giorgia; Fiorilli, Sonia; Caneschi, Andrea; Vitale-Brovarone, Chiara

2018-04-28

Bone tissue engineering offers an alternative promising solution to treat a large number of bone injuries with special focus on pathological conditions, such as osteoporosis. In this scenario, the bone tissue regeneration may be promoted using bioactive and biomimetic materials able to direct cell response, while the desired scaffold architecture can be tailored by means of 3D printing technologies. In this context, our study aimed to develop a hybrid bioactive material suitable for 3D printing of scaffolds mimicking the natural composition and structure of healthy bone. Type I collagen and strontium-containing mesoporous bioactive glasses were combined to obtain suspensions able to perform a sol-gel transition under physiological conditions. Field emission scanning electron microscopy (FESEM) analyses confirmed the formation of fibrous nanostructures homogeneously embedding inorganic particles, whereas bioactivity studies demonstrated the large calcium phosphate deposition. The high-water content promoted the strontium ion release from the embedded glass particles, potentially enhancing the osteogenic behaviour of the composite. Furthermore, the suspension printability was assessed by means of rheological studies and preliminary extrusion tests, showing shear thinning and fast material recovery upon deposition. In conclusion, the reported results suggest that promising hybrid systems suitable for 3D printing of bioactive scaffolds for bone tissue engineering have been developed.

Material characteristics and construction methods for a typical research reactor concrete containment in Iran

International Nuclear Information System (INIS)

Ebrahimia, Mahsa; Suha, Kune Y.; Eghbalic, Rahman; Jahan, Farzaneh Asadi malek

2012-01-01

Generally selecting an appropriate material and also construction style for a concrete containment due to its function and special geometry play an important role in applicability and also construction cost and duration decrease in a research reactor (RR) project. The reactor containment enclosing the reactor vessel comprises physical barriers reflecting the safety design and construction codes, regulations and standards so as to prevent the community and the environment from uncontrolled release of radioactive materials. It is the third and the last barrier against radioactivity release. It protects the reactor vessel from such external events as earthquake and aircraft crash as well. Thus, it should be designed and constructed in such a manner as to withstand dead and live loads, ground and seismic loads, missiles and aircraft loads, and thermal and shrinkage loads. This study aims to present a construction method for concrete containment of a typical RR in Iran. The work also presents an acceptable characteristic for concrete and reinforcing re bar of a typical concrete containment. The current study has evaluated the various types of the RR containments. The most proper type was selected in accordance with the current knowledge and technology of Iran

Material characteristics and construction methods for a typical research reactor concrete containment in Iran

Energy Technology Data Exchange (ETDEWEB)

Ebrahimia, Mahsa; Suha, Kune Y. [Seoul National Univ., Seoul (Korea, Republic of); Eghbalic, Rahman; Jahan, Farzaneh Asadi malek [School of Architecture and Urbanism, Qazvin (Iran, Islamic Republic of)

2012-10-15

Generally selecting an appropriate material and also construction style for a concrete containment due to its function and special geometry play an important role in applicability and also construction cost and duration decrease in a research reactor (RR) project. The reactor containment enclosing the reactor vessel comprises physical barriers reflecting the safety design and construction codes, regulations and standards so as to prevent the community and the environment from uncontrolled release of radioactive materials. It is the third and the last barrier against radioactivity release. It protects the reactor vessel from such external events as earthquake and aircraft crash as well. Thus, it should be designed and constructed in such a manner as to withstand dead and live loads, ground and seismic loads, missiles and aircraft loads, and thermal and shrinkage loads. This study aims to present a construction method for concrete containment of a typical RR in Iran. The work also presents an acceptable characteristic for concrete and reinforcing re bar of a typical concrete containment. The current study has evaluated the various types of the RR containments. The most proper type was selected in accordance with the current knowledge and technology of Iran.

Radiation levels on empty cylinders containing heel material

Energy Technology Data Exchange (ETDEWEB)

Shockley, C.W. [Martin Marietta Energy Systems, Inc., Paducah, KY (United States)

1991-12-31

Empty UF{sub 6} cylinders containing heel material were found to emit radiation levels in excess of 200 mr/hr, the maximum amount stated in ORO-651. The radiation levels were as high as 335 mr/hr for thick wall (48X and 48Y) cylinders and 1050 mr/hr for thin wall (48G and 48H) cylinders. The high readings were found only on the bottom of the cylinders. These radiation levels exceeded the maximum levels established in DOT 49 CFR, Part 173.441 for shipment of cylinders. Holding periods of four weeks for thick-wall cylinders and ten weeks for thin-wall cylinders were established to allow the radiation levels to decay prior to shipment.

Natural material-decorated mesoporous silica nanoparticle container for multifunctional membrane-controlled targeted drug delivery

Directory of Open Access Journals (Sweden)

Hu Y

2017-11-01

Full Text Available Yan Hu,1 Lei Ke,2 Hao Chen,1 Ma Zhuo,1 Xinzhou Yang,1 Dan Zhao,1 Suying Zeng,1 Xincai Xiao1 1Department of Pharmaceutics, School of Pharmaceutical Science, South-Central University for Nationalities, 2Department of Medicinal Chemistry, School of Pharmacy, Tongji Medical College, Huazhong University of Science and Technology, Wuhan, People’s Republic of China Abstract: To avoid the side effects caused by nonspecific targeting, premature release, weak selectivity, and poor therapeutic efficacy of current nanoparticle-based systems used for drug delivery, we fabricated natural material-decorated nanoparticles as a multifunctional, membrane-controlled targeted drug delivery system. The nanocomposite material coated with a membrane was biocompatible and integrated both specific tumor targeting and responsiveness to stimulation, which improved transmission efficacy and controlled drug release. Mesoporous silica nanoparticles (MSNs, which are known for their biocompatibility and high drug-loading capacity, were selected as a model drug container and carrier. The membrane was established by the polyelectrolyte composite method from chitosan (CS which was sensitive to the acidic tumor microenvironment, folic acid-modified CS which recognizes the folate receptor expressed on the tumor cell surface, and a CD44 receptor-targeted polysaccharide hyaluronic acid. We characterized the structure of the nanocomposite as well as the drug release behavior under the control of the pH-sensitive membrane switch and evaluated the antitumor efficacy of the system in vitro. Our results provide a basis for the design and fabrication of novel membrane-controlled nanoparticles with improved tumor-targeting therapy. Keywords: multifunctional, membrane-controlled, natural materials, mesoporous silica nanoparticles, targeted drug delivery

Effects of earthquake induced rock shear on containment system integrity. Laboratory testing plan development

International Nuclear Information System (INIS)

Read, Rodney S.

2011-07-01

This report describes a laboratory-scale testing program plan to address the issue of earthquake induced rock shear effects on containment system integrity. The document contains a review of relevant literature from SKB covering laboratory testing of bentonite clay buffer material, scaled analogue tests, and the development of related material models to simulate rock shear effects. The proposed testing program includes standard single component tests, new two-component constant volume tests, and new scaled analogue tests. Conceptual drawings of equipment required to undertake these tests are presented along with a schedule of tests. The information in this document is considered sufficient to engage qualified testing facilities, and to guide implementation of laboratory testing of rock shear effects. This document was completed as part of a collaborative agreement between SKB and Nuclear Waste Management Organization (NWMO) in Canada

Effects of earthquake induced rock shear on containment system integrity. Laboratory testing plan development

Energy Technology Data Exchange (ETDEWEB)

Read, Rodney S. (RSRead Consulting Inc. (Canada))

2011-07-15

This report describes a laboratory-scale testing program plan to address the issue of earthquake induced rock shear effects on containment system integrity. The document contains a review of relevant literature from SKB covering laboratory testing of bentonite clay buffer material, scaled analogue tests, and the development of related material models to simulate rock shear effects. The proposed testing program includes standard single component tests, new two-component constant volume tests, and new scaled analogue tests. Conceptual drawings of equipment required to undertake these tests are presented along with a schedule of tests. The information in this document is considered sufficient to engage qualified testing facilities, and to guide implementation of laboratory testing of rock shear effects. This document was completed as part of a collaborative agreement between SKB and Nuclear Waste Management Organization (NWMO) in Canada

Spectral studies on the interaction of acetylacetone with aluminum-containing MCM-41 mesoporous materials

International Nuclear Information System (INIS)

Zanjanchi, M.A.; Vaziri, M.

2008-01-01

Diffuse reflectance spectroscopy (DRS) was used to study the interaction of acetylacetone (acac) with the mesoporous aluminum-containing MCM-41 materials. A room temperature synthesis method was used for preparation of purely siliceous MCM-41 and for aluminum-containing MCM-41 materials. Samples with Si/Al ratios of 50, 20, 10 and 5 were synthesized. The synthesized mesoporous materials possess highly ordered structure and high surface area as evidenced from X-ray diffraction and nitrogen physisorption measurements, respectively. The treatment of the as-synthesized aluminum-containing MCM-41 samples with acac shows a distinct band at ∼290 nm. This band is assigned to six coordinated aluminum atoms in the structure which is produced by diffusion of acac molecules through surfactant micelles and their interaction with aluminum atoms. The 290-nm band disappears upon several successive washing of the sample with ethanol. The treatment of the calcined aluminum-containing MCM-41 sample with acac produces the same 290-nm band where its intensity increases with the aluminum content of the sample. The intensity of this band is reduced upon successive ethanol washing, but remains nearly constant after three times washing. This irremovable aluminum species can be assigned to framework aluminum. The measured acidity for our aluminum-containing MCM-41 samples correlates linearly with the intensity of 290-nm band for the ethanol treated samples. This supports the idea that the Bronsted acidity in aluminum-modified MCM-41 samples is a function of the amount of tetrahedral framework aluminum in the structure

Mass extraction container closure integrity physical testing method development for parenteral container closure systems.

Science.gov (United States)

Yoon, Seung-Yil; Sagi, Hemi; Goldhammer, Craig; Li, Lei

2012-01-01

Container closure integrity (CCI) is a critical factor to ensure that product sterility is maintained over its entire shelf life. Assuring the CCI during container closure (C/C) system qualification, routine manufacturing and stability is important. FDA guidance also encourages industry to develop a CCI physical testing method in lieu of sterility testing in a stability program. A mass extraction system has been developed to check CCI for a variety of container closure systems such as vials, syringes, and cartridges. Various types of defects (e.g., glass micropipette, laser drill, wire) were created and used to demonstrate a detection limit. Leakage, detected as mass flow in this study, changes as a function of defect length and diameter. Therefore, the morphology of defects has been examined in detail with fluid theories. This study demonstrated that a mass extraction system was able to distinguish between intact samples and samples with 2 μm defects reliably when the defect was exposed to air, water, placebo, or drug product (3 mg/mL concentration) solution. Also, it has been verified that the method was robust, and capable of determining the acceptance limit using 3σ for syringes and 6σ for vials. Sterile products must maintain their sterility over their entire shelf life. Container closure systems such as those found in syringes and vials provide a seal between rubber and glass containers. This seal must be ensured to maintain product sterility. A mass extraction system has been developed to check container closure integrity for a variety of container closure systems such as vials, syringes, and cartridges. In order to demonstrate the method's capability, various types of defects (e.g., glass micropipette, laser drill, wire) were created in syringes and vials and were tested. This study demonstrated that a mass extraction system was able to distinguish between intact samples and samples with 2 μm defects reliably when the defect was exposed to air, water

Igloo containment system for improvised explosive devices

International Nuclear Information System (INIS)

Dyckes, G.W.

1980-09-01

A method for containing or partially containing the blast and dispersal of radioactive particulate from improvised explosive devices is described. The containment system is restricted to devices located in fairly open areas at ground level, e.g., devices concealed in trucks, vans, transportainers, or small buildings which are accessible from all sides

Development of assessment methods for transport and storage containers with higher content of metallic recycling material

International Nuclear Information System (INIS)

Zencker, U.; Qiao Linan; Droste, B.

2004-01-01

The mechanical behaviour of transport and storage containers made of ductile cast iron melted with higher content of metallic recycling material from decommissioning and dismantling of nuclear installations is investigated. With drop tests of cubic container-like models, the influence of different real targets on the stresses in the cask body and the fracture behaviour is examined. A test stand foundation is suggested, which can be manufactured simply and improves the reproducibility of the test results strongly. The test objects are partially equipped with artificial cracklike defects. Dynamic fracture mechanics analyses of these defects were performed by means of finite element calculations to uncover safety margins. Numerous test results show depending on the requirements that containers for final disposal can be built by means of a ductile cast iron with fracture toughness more than half under the lower bound value for the licensed material qualities yet. The application limits of the material are determined also by the opportunities of the safety assessment methods. This project supports the application of brittle fracture safe transport and storage packages for radioactive materials as recommended in App. VI of the Advisory Material for the IAEA Regulations for the Safe Transport of Radioactive Material (IAEA No. TS-G-1.1)

Development of assessment methods for transport and storage containers with higher content of metallic recycling material

Energy Technology Data Exchange (ETDEWEB)

Zencker, U.; Qiao Linan; Droste, B. [Bundesanstalt fuer Materialforschung und -pruefung (BAM), Berlin (Germany)

2004-07-01

The mechanical behaviour of transport and storage containers made of ductile cast iron melted with higher content of metallic recycling material from decommissioning and dismantling of nuclear installations is investigated. With drop tests of cubic container-like models, the influence of different real targets on the stresses in the cask body and the fracture behaviour is examined. A test stand foundation is suggested, which can be manufactured simply and improves the reproducibility of the test results strongly. The test objects are partially equipped with artificial cracklike defects. Dynamic fracture mechanics analyses of these defects were performed by means of finite element calculations to uncover safety margins. Numerous test results show depending on the requirements that containers for final disposal can be built by means of a ductile cast iron with fracture toughness more than half under the lower bound value for the licensed material qualities yet. The application limits of the material are determined also by the opportunities of the safety assessment methods. This project supports the application of brittle fracture safe transport and storage packages for radioactive materials as recommended in App. VI of the Advisory Material for the IAEA Regulations for the Safe Transport of Radioactive Material (IAEA No. TS-G-1.1).

DEMONSTRATiON OF A SUBSURFACE CONTAINMENT SYSTEM FOR INSTALLATION AT DOE WASTE SITES

Energy Technology Data Exchange (ETDEWEB)

Thomas J. Crocker; Verna M. Carpenter

2003-05-21

Between 1952 and 1970, DOE buried mixed waste in pits and trenches that now have special cleanup needs. The disposal practices used decades ago left these landfills and other trenches, pits, and disposal sites filled with three million cubic meters of buried waste. This waste is becoming harmful to human safety and health. Today's cleanup and waste removal is time-consuming and expensive with some sites scheduled to complete cleanup by 2006 or later. An interim solution to the DOE buried waste problem is to encapsulate and hydraulically isolate the waste with a geomembrane barrier and monitor the performance of the barrier over its 50-yr lifetime. The installed containment barriers would isolate the buried waste and protect groundwater from pollutants until final remediations are completed. The DOE has awarded a contract to RAHCO International, Inc.; of Spokane, Washington; to design, develop, and test a novel subsurface barrier installation system, referred to as a Subsurface Containment System (SCS). The installed containment barrier consists of commercially available geomembrane materials that isolates the underground waste, similar to the way a swimming pools hold water, without disrupting hazardous material that was buried decades ago. The barrier protects soil and groundwater from contamination and effectively meets environmental cleanup standards while reducing risks, schedules, and costs. Constructing the subsurface containment barrier uses a combination of conventional and specialized equipment and a unique continuous construction process. This innovative equipment and construction method can construct a 1000-ft-long X 34-ft-wide X 30-ft-deep barrier at construction rates to 12 Wday (8 hr/day operation). Life cycle costs including RCRA cover and long-term monitoring range from approximately $380 to $590/cu yd of waste contained or $100 to $160/sq ft of placed barrier based upon the subsurface geology surrounding the waste. Project objectives for Phase

Micromechanical Analysis of Crack Closure Mechanism for Intelligent Material Containing TiNi Fibers

Science.gov (United States)

Araki, Shigetoshi; Ono, Hiroyuki; Saito, Kenji

In our previous study, the micromechanical modeling of an intelligent material containing TiNi fibers was performed and the stress intensity factor KI at the tip of the crack in the material was expressed in terms of the magnitude of the shape memory shrinkage of the fibers and the thermal expansion strain in the material. In this study, the value of KI at the tip of the crack in the TiNi/epoxy material is calculated numerically by using analytical expressions obtained in our first report. As a result, we find that the KI value decreases with increasing shrink strain of the fibers, and this tendency agrees with that of the experimental result obtained by Shimamoto etal.(Trans. Jpn. Soc. Mech. Eng., Vol. 65, No. 634 (1999), pp. 1282-1286). Moreover, there exists an optimal value of the shrink strain of the fibers to make the KI value zero. The change in KI with temperature during the heating process from the reference temperature to the inverse austenitic finishing temperature of TiNi fiber is also consistent with the experimental result. These results can be explained by the changes in the shrink strain, the thermal expansion strain, and the elastic moduli of TiNi fiber with temperature. These results may be useful in designing intelligent materials containing TiNi fibers from the viewpoint of crack closure.

DISPOSAL CONTAINER HANDLING SYSTEM DESCRIPTION DOCUMENT

Energy Technology Data Exchange (ETDEWEB)

E. F. Loros

2000-06-30

The Disposal Container Handling System receives and prepares new disposal containers (DCs) and transfers them to the Assembly Transfer System (ATS) or Canister Transfer System (CTS) for loading. The system receives the loaded DCs from ATS or CTS and welds the lids. When the welds are accepted the DCs are termed waste packages (WPs). The system may stage the WP for later transfer or transfer the WP directly to the Waste Emplacement/Retrieval System. The system can also transfer DCs/WPs to/from the Waste Package Remediation System. The Disposal Container Handling System begins with new DC preparation, which includes installing collars, tilting the DC upright, and outfitting the container for the specific fuel it is to receive. DCs and their lids are staged in the receipt area for transfer to the needed location. When called for, a DC is put on a cart and sent through an airlock into a hot cell. From this point on, all processes are done remotely. The DC transfer operation moves the DC to the ATS or CTS for loading and then receives the DC for welding. The DC welding operation receives loaded DCs directly from the waste handling lines or from interim lag storage for welding of the lids. The welding operation includes mounting the DC on a turntable, removing lid seals, and installing and welding the inner and outer lids. After the weld process and non-destructive examination are successfully completed, the WP is either staged or transferred to a tilting station. At the tilting station, the WP is tilted horizontally onto a cart and the collars removed. The cart is taken through an air lock where the WP is lifted, surveyed, decontaminated if required, and then moved into the Waste Emplacement/Retrieval System. DCs that do not meet the welding non-destructive examination criteria are transferred to the Waste Package Remediation System for weld preparation or removal of the lids. The Disposal Container Handling System is contained within the Waste Handling Building System

A formula for determination of swelling characteristics of buffer material containing bentonite and evaluation of self-sealing performance

International Nuclear Information System (INIS)

Komine, Hideo; Ogata, Nobuhide

1998-01-01

High level radioactive waste disposal facility is planned to construct in a rock board deeper than some hundreds meter at underground, it is necessary to develop a material to refill the gap between waste container and its circumferential rock board. For this material it is required to have high water sealing and swellability, and bentonite is expected to use such application. Production of soil buffer materials containing bentonite is difficult to obtain required dry density by solidifying due to in situ roll-pressing, so it is, at present, thought to be an effective method to carry a block produced in a factory to a pit for disposal to settle. When supposing to produce and settle such buffer material, a gap forming between the buffer material and circumferential rock board or waste container has a large possibility to make a water path when remaining without treating it. Therefore, the buffer material is required to have a function to fill gap portion by swelling deformation and to proof water. In this study, in order to evaluated self-sealing of bentonite, due to a theoretical examination and a laboratory experiment on swelling behavior of soil materials containing bentonite, a swelling evaluation equation of the buffer materials was proposed. And, an application example for outlined design of an actual high level radioactive waste disposal facility was introduced. (G.K.)

Reference material systems: a sourcebook for material assessment

Energy Technology Data Exchange (ETDEWEB)

Bhagat, N. (ed.)

1976-12-01

A reference set of data related to material systems and a framework for carrying out the material technologies assessment are presented. While the bulk of renewables have been considered in this report, the nonrenewable materials dealt with here include structural materials only, such as steel, aluminum, cement and concrete, and bricks. The complete data set is supposed to include material flows, energy requirements, capital and labor inputs, and environmental effects for each process that a resource must go through to become a useful material for an end use. Although effort has been made to obtain as much information as possible, considerable gaps in data, apparent throughout this report, could not be avoided. A new material technology can be evaluated by substituting that technology for appropriate elements of the reference materials system and calculating the net change in material resource, energy, capital and labor requirements, and environmental impacts. This combination of information thus serves as a means of evaluating the potential benefits to be gained by research in various material technologies.

Nupack, the new ASME code for radioactive material transportation packaging containments

International Nuclear Information System (INIS)

Turula, P.

1998-01-01

The American Society of Mechanical Engineers (ASME) has added a new division to the nuclear construction section of its Boiler and Pressure Vessel Code (B and PVC). This Division, commonly referred to as Nupack, has been written to provide a consistent set of technical requirements for containment vessels of transportation packagings for high-level radioactive materials. This paper provides an introduction to Nupack, discusses some of its technical provisions, and describes how it can be used for the design and construction of packaging components. Nupack's general provisions and design requirements are emphasized, while treatment of materials, fabrication and inspection is left for another paper

Loop containment (joint integrity) assessment Brayton Isotope Power System flight system

International Nuclear Information System (INIS)

1976-01-01

The Brayton Isotope Power System (BIPS) contains a large number of joints. Since the failure of a joint would result in loss of the working fluid and consequential failure of the BIPS, the integrity of the joints is of paramount importance. The reliability of the ERDA BIPS loop containment (joint integrity) is evaluated. The conceptual flight system as presently configured is depicted. A brief description of the flight system is given

Luminescent materials based on Tb, Eu-containing layered double hydroxides

International Nuclear Information System (INIS)

Zhuravleva, N.G.; Eliseev, A.A.; Lukashin, A.V.; Kinast, U.; Tret'yakov, Yu.D.

2004-01-01

Luminescent materials on the basis of magnesium-aluminium layered double hydroxides with intercalated anionic complexes of terbium and europium picolinates were synthesized. Relying on data of spectroscopy, elementary and X-ray phase analyses, the change in the rare earth complex structure and metal/ligand ratio, depending on the hydroxide layer charge, determined by Mg/Al ratio in the double hydroxide, were ascertained. The values of quantum yields of luminescence for terbium-containing samples amounted to 30-50% [ru

TEMPERATURE PREDICTION IN 3013 CONTAINERS IN K AREA MATERIAL STORAGE (KAMS) FACILITY USING REGRESSION METHODS

International Nuclear Information System (INIS)

Gupta, N

2008-01-01

3013 containers are designed in accordance with the DOE-STD-3013-2004. These containers are qualified to store plutonium (Pu) bearing materials such as PuO2 for 50 years. DOT shipping packages such as the 9975 are used to store the 3013 containers in the K-Area Material Storage (KAMS) facility at Savannah River Site (SRS). DOE-STD-3013-2004 requires that a comprehensive surveillance program be set up to ensure that the 3013 container design parameters are not violated during the long term storage. To ensure structural integrity of the 3013 containers, thermal analyses using finite element models were performed to predict the contents and component temperatures for different but well defined parameters such as storage ambient temperature, PuO 2 density, fill heights, weights, and thermal loading. Interpolation is normally used to calculate temperatures if the actual parameter values are different from the analyzed values. A statistical analysis technique using regression methods is proposed to develop simple polynomial relations to predict temperatures for the actual parameter values found in the containers. The analysis shows that regression analysis is a powerful tool to develop simple relations to assess component temperatures

Modeling property evolution of container materials used in nuclear waste storage

Science.gov (United States)

Li, Dongsheng; Garmestani, Hamid; Khaleel, Moe; Sun, Xin

2010-03-01

Container materials under irradiation for a long time will raise high energy in the structure to generate critical structural damage. This study investigated what kind of mesoscale microstructure will be more resistant to radiation damage. Mechanical properties evolution during irradiation was modeled using statistical continuum mechanics. Preliminary results also showed how to achieve the desired microstructure with higher resistance to radiation.

Polymers Containing Diphenylvinyl-Substituted Indole Rings as Charge-Transporting Materials for OLEDs

Science.gov (United States)

Grigalevicius, S.; Zostautiene, R.; Sipaviciute, D.; Stulpinaite, B.; Volyniuk, D.; Grazulevicius, J. V.; Liu, L.; Xie, Z.; Zhang, B.

2016-02-01

Monomers and polymers containing electronically isolated diphenylvinyl-substituted indole rings were synthesized and characterized by nuclear magnetic resonance (NMR) and mass spectroscopies as well as by gel permeation chromatography. The polymers represent amorphous materials with glass transition temperatures of 91-109°C and thermal decomposition starting above 307°C. Electron photoemission spectra of thin films of the synthesized polymers revealed ionization potentials of 5.54-5.58 eV. The synthesized polymers were tested as hole-transporting materials in simple electroluminescent organic light-emitting diode (OLED) devices with tris(quinolin-8-olato)aluminium (Alq3) as an emitter as well as an electron-transporting layer. A green OLED device containing a hole-transporting layer of poly[1-(2,3-epithiopropyl)-2-methyl-3-(2,2-diphenylvinyl)índole] exhibited the best overall performance with a driving voltage of 4.0 V, maximum photometric efficiency of 2.8 cd/A and maximum brightness of about 4200 cd/m2.

Active containment systems incorporating modified pillared clays

International Nuclear Information System (INIS)

Lundie, P.; McLeod, N.

1997-01-01

The application of treatment technologies in active containment systems provides a more advanced and effective method for the remediation of contaminated sites. These treatment technologies can be applied in permeable reactive walls and/or funnel and gate systems. The application of modified pillared clays in active containment systems provides a mechanism for producing permeable reactive walls with versatile properties. These pillared clays are suitably modified to incorporate reactive intercalatants capable of reacting with both a broad range of organic pollutants of varying molecular size, polarity and reactivity. Heavy metals can be removed from contaminated water by conventional ion-exchange and other reactive processes within the clay structure. Complex contamination problems can be addressed by the application of more than one modified clay on a site specific basis. This paper briefly describes the active containment system and the structure/chemistry of the modified pillared clay technology, illustrating potential applications of the in-situ treatment process for contaminated site remediation

Simplified safety and containment systems for the iris reactor

International Nuclear Information System (INIS)

Conway, L.E.; Lombardi, C.; Ricotti, M.; Oriani, L.

2001-01-01

The IRIS (International Reactor Innovative and Secure) is a 100 - 300 MW modular type pressurized water reactor supported by the U.S. DOE NERI Program. IRIS features a long-life core to provide proliferation resistance and to reduce the volume of spent fuel, as well as reduce maintenance requirements. IRIS utilizes an integral reactor vessel that contains all major primary system components. This integral reactor vessel makes it possible to reduce containment size; making the IRIS more cost competitive. IRIS is being designed to enhance reactor safety, and therefore a key aspect of the IRIS program is the development of the safety and containment systems. These systems are being designed to maximize containment integrity, prevent core uncover following postulated accidents, minimize the probability and consequences of severe accidents, and provide a significant simplification over current safety system designs. The design of the IRIS containment and safety systems has been identified and preliminary analyses have been completed. The IRIS safety concept employs some unique features that minimize the consequences of postulated design basis events. This paper will provide a description of the containment design and safety systems, and will summarize the analysis results. (author)

Materials, processes, and environmental engineering network

Science.gov (United States)

White, Margo M.

1993-01-01

The Materials, Processes, and Environmental Engineering Network (MPEEN) was developed as a central holding facility for materials testing information generated by the Materials and Processes Laboratory. It contains information from other NASA centers and outside agencies, and also includes the NASA Environmental Information System (NEIS) and Failure Analysis Information System (FAIS) data. Environmental replacement materials information is a newly developed focus of MPEEN. This database is the NASA Environmental Information System, NEIS, which is accessible through MPEEN. Environmental concerns are addressed regarding materials identified by the NASA Operational Environment Team, NOET, to be hazardous to the environment. An environmental replacement technology database is contained within NEIS. Environmental concerns about materials are identified by NOET, and control or replacement strategies are formed. This database also contains the usage and performance characteristics of these hazardous materials. In addition to addressing environmental concerns, MPEEN contains one of the largest materials databases in the world. Over 600 users access this network on a daily basis. There is information available on failure analysis, metals and nonmetals testing, materials properties, standard and commercial parts, foreign alloy cross-reference, Long Duration Exposure Facility (LDEF) data, and Materials and Processes Selection List data.

The inventory of interstellar materials available for the formation of the solar system

Science.gov (United States)

Sandford, Scott A.

1996-07-01

Tremendous progress has been made in the field of interstellar dust in recent years through the use of telescopic observations, theoretical studies, laboratory studies of analogs, and the study of actual interstellar samples found in meteorites. It is increasingly clear that the interstellar medium (ISM) contains an enormous diversity of materials created by a wide range of chemical and physical processes. This understanding is a far cry from the picture of interstellar materials held as recently as two decades ago, a picture which incorporated only a few generic types of grains and few molecules. In this paper, I attempt to review some of our current knowledge of the more abundant materials thought to exist in the ISM. The review concentrates on matter in interstellar dense molecular clouds since it is the materials in these environments from which new stars and planetary systems are formed. However, some discussion is reserved for materials in circumstellar environments and in the diffuse ISM. The paper also focuses largely on solid materials as opposed to gases since solids contain a major fraction of the heavier elements in clouds and because solids are most likely to survive incorporation into new planetary systems in identifiable form. The paper concludes with a discussion of some of the implications resulting from the recent growth of our knowledge about interstellar materials and also considers a number of areas in which future work might be expected to yield important results.

Mockup of an automated material transport system for remote handling

International Nuclear Information System (INIS)

Porter, M.L.

1992-01-01

The automated material transport system (AMTS) was conceived for the transport of samples within the material and process control laboratory (MPCL), located in the plutonium processing building of the special isotope separation (SIS) facility. The MPCL was designed with a dry sample handling laboratory and a wet chemistry analysis laboratory. Each laboratory contained several processing glove boxes. The function of the AMTS was to automate the handling of materials, multiple process samples, and bulky items between process stations with a minimum of operator intervention and with a minimum of waiting periods and nonproductive activities. The AMTS design requirements, design verification mockup plan, and AMTS mockup procurement specification were established prior to cancellation of the SIS project. Due to the AMTS's flexibility, the need for technology development, and applicability to other US Department of Energy facilities, mockup of the AMTS continued. This paper discusses the system design features, capabilities, and results of initial testing

MISSE in the Materials and Processes Technical Information System (MAPTIS )

Science.gov (United States)

Burns, DeWitt; Finckenor, Miria; Henrie, Ben

2013-01-01

Materials International Space Station Experiment (MISSE) data is now being collected and distributed through the Materials and Processes Technical Information System (MAPTIS) at Marshall Space Flight Center in Huntsville, Alabama. MISSE data has been instrumental in many programs and continues to be an important source of data for the space community. To facilitate great access to the MISSE data the International Space Station (ISS) program office and MAPTIS are working to gather this data into a central location. The MISSE database contains information about materials, samples, and flights along with pictures, pdfs, excel files, word documents, and other files types. Major capabilities of the system are: access control, browsing, searching, reports, and record comparison. The search capabilities will search within any searchable files so even if the desired meta-data has not been associated data can still be retrieved. Other functionality will continue to be added to the MISSE database as the Athena Platform is expanded

Uncanistered Spent Nuclear fuel Disposal Container System Description Document

International Nuclear Information System (INIS)

Pettit, N. E.

2001-01-01

The Uncanistered Spent Nuclear Fuel (SNF) Disposal Container System supports the confinement and isolation of waste within the Engineered Barrier System of the Monitored Geologic Repository (MGR). Disposal containers are loaded with intact uncanistered assemblies and/or individually canistered SNF assemblies and sealed in the surface waste handling facilities, transferred to the underground through the access drifts, and emplaced in emplacement drifts. The Uncanistered SNF Disposal Container provides long-term confinement of the commercial SNF placed inside, and withstands the loading, transfer, emplacement, and retrieval loads and environments. The Uncanistered SNF Disposal Container System provides containment of waste for a designated period of time, and limits radionuclide release. The disposal container maintains the waste in a designated configuration, withstands maximum handling and rockfall loads, limits the individual SNF assembly temperatures after emplacement, limits the introduction of moderator into the disposal container during the criticality control period, resists corrosion in the expected handling and repository environments, and provides containment of waste in the event of an accident

Waste container and method for containing waste

International Nuclear Information System (INIS)

Ono, Akira; Matsushita, Mitsuhiro; Doi, Makoto; Nakatani, Seiichi.

1990-01-01

In a waste container, water-proof membranes and rare earth element layers are formed on the inner surface of a steel plate concrete container in which steel plates are embedded. Further, rear earth element detectors are disposed each from the inner side of the steel plate concrete container by way of a pressure pipe to the outer side of the container. As a method for actually containing wastes, when a plurality of vessels in which wastes are fixed are collectively enhoused to the waste container, cussioning materials are attached to the inner surface of the container and wastes fixing containers are stacked successively in a plurality of rows in a bag made of elastic materials. Subsequently, fixing materials are filled and tightly sealed in the waste container. When the waste container thus constituted is buried underground, even if it should be deformed to cause intrusion of rain water to the inside of the container, the rare earth elements in the container dissolved in the rain water can be detected by the detectors, the containers are exchanged before the rain water intruding to the inner side is leached to the surrounding ground, to previously prevent the leakage of radioactive nuclides. (K.M.)

APPLICATION OF A GEOGRAPHIC INFORMATION SYSTEM FOR A CONTAINMENT SYSTEM LEAK DETECTION

Science.gov (United States)

The use of physical and hydraulic containment systems for the isolation of contaminated ground water associated with hazardous waste sites has increased during the last decade. Existing methodologies for monitoring and evaluating leakage from hazardous waste containment systems ...

Gross Containment Leakage Monitoring System (GCLM) applied to accidental impairment of containment integrity determination

International Nuclear Information System (INIS)

Dinu, Camelia; Talpalariu, A.; Constantinescu, G.

2007-01-01

The Prioritization of Generic Safety Issues (NUREG-0933 of October 2006), section 1 task II.E.4 item II.E.4.3 recommends that a method of periodic or continuous testing has to be available, in order to detect unknown gross openings in the nuclear power plants containment structure. The Palisades incident and three other incidents are exemplified, when the reactor was operated for about 1.5 years, while the containment isolation valves in a purge system bypass line were unknowingly locked in the open position. It was estimated that the presence of a GCLM system could identify an unknown breach and reduce the expected unavailability of containment due to containment integrity breach events, to a 1.6x10 -3 /year demand. (authors)

The status of the Bubbler Condenser Containment System for the Reactors of the VVER-440/213 Type

International Nuclear Information System (INIS)

Karwat, H.; Rosinger, H.E.

1998-01-01

VVER-440/213 Pressurized Water Reactors have a pressure-suppression containment structure called a 'Bubbler Condenser' tower which can reduce the design pressure of the entire containment following a design basis accident (DBA), such as a loss-of-coolant accident (LOCA). The bubbler condenser pressure suppression system provides reduction of the LOCA containment pressure by the condensation of released steam in a water pool. World-wide there are 14 nuclear power plants of the VVER-440/213 type in Eastern Europe and Russia. One of the safety concerns for the VVER-440/213 reactors relates to the ability of the bubbler condenser containment system to function satisfactorily and to maintain its integrity following certain postulated accidents and thus limit the release of radioactive material to the environment. The complicated geometry of the bubbler condenser unit, and the dependence on several moving devices and interlocks are the main doubts expressed by different specialists with regard to the design. General description of the bubbler condenser containment system, the physical processes, concerns and design assessment of the bubbler condenser containment system, presentation of the OECD's Unified Bubbler Condenser Research Project (UBCRP) and the European Commission PHARE/TACIS project. Recent utility investigations are also discussed

Tunable multichannel filter in photonic crystal heterostructure containing permeability-negative materials

International Nuclear Information System (INIS)

Hu Xiaoyong; Liu Zheng; Gong Qihuang

2008-01-01

A tunable multichannel filter is demonstrated theoretically based on a one-dimensional photonic crystal heterostructure containing permeability-negative material. The filtering properties of the photonic crystal filter, including the channel number and frequency, can be tuned by adjusting the structure parameters or by a pump laser. The angular response of the photonic crystal filter and the influences of the losses on the filtering properties are also analyzed

Tunable multichannel filter in photonic crystal heterostructure containing permeability-negative materials

Energy Technology Data Exchange (ETDEWEB)

Hu Xiaoyong [State Key Laboratory for Mesoscopic Physics, Department of Physics, Peking University, Beijing 100871 (China)], E-mail: xiaoyonghu@pku.edu.cn; Liu Zheng [State Key Laboratory for Mesoscopic Physics, Department of Physics, Peking University, Beijing 100871 (China); Gong Qihuang [State Key Laboratory for Mesoscopic Physics, Department of Physics, Peking University, Beijing 100871 (China)], E-mail: qhgong@pku.edu.cn

2008-01-14

A tunable multichannel filter is demonstrated theoretically based on a one-dimensional photonic crystal heterostructure containing permeability-negative material. The filtering properties of the photonic crystal filter, including the channel number and frequency, can be tuned by adjusting the structure parameters or by a pump laser. The angular response of the photonic crystal filter and the influences of the losses on the filtering properties are also analyzed.

Transportation of radioactive materials: the legislative and regulatory information system

International Nuclear Information System (INIS)

Fore, C.S.

1982-03-01

The US Department of Energy is carrying out a national program to assure the safe shipment of radioactive materials. As part of this overall effort, the Hazardous Materials Information Center of Oak Ridge National Laboratory has developed the comprehensive Legislative and Regulatory Information System, which contains information on federal-, state-, and local-level legislative and regulatory actions pertaining primarily to the shipment of radioactive materials. Specific subject areas chosen to highlight particular transportation restrictions include: (1) identification of state agency responsible for regulating transportation, (2) type of escorts required, (3) areas requiring prior notification, (4) areas requiring permits or licenses, and (5) areas totally banning transportation of all radioactive materials. Other legislative information being categorized and of immediate relevance to the transportation issues is covered under the areas of disposal, storage, and management of radioactive materials; establishment of additional regulations; emergency response regulations; moratoriums on power plant construction and siting; radiation safety and control studies; and remedial action studies. The collected information is abstracted, indexed, and input into one of the two data bases developed under this information system - Current Legislation Data Base and Historical Legislation Data Base. An appendix is included which provides a summary of the state and local laws affecting the transportation of radioactive materials throughout the United States. The Legislative and Regulatory Information System is supported by the Transportation Technology Center located at Sandia National Laboratories, Albuquerque, New Mexico

Transportation of radioactive materials: the legislative and regulatory information system

Energy Technology Data Exchange (ETDEWEB)

Fore, C.S.

1982-03-01

The US Department of Energy is carrying out a national program to assure the safe shipment of radioactive materials. As part of this overall effort, the Hazardous Materials Information Center of Oak Ridge National Laboratory has developed the comprehensive Legislative and Regulatory Information System, which contains information on federal-, state-, and local-level legislative and regulatory actions pertaining primarily to the shipment of radioactive materials. Specific subject areas chosen to highlight particular transportation restrictions include: (1) identification of state agency responsible for regulating transportation, (2) type of escorts required, (3) areas requiring prior notification, (4) areas requiring permits or licenses, and (5) areas totally banning transportation of all radioactive materials. Other legislative information being categorized and of immediate relevance to the transportation issues is covered under the areas of disposal, storage, and management of radioactive materials; establishment of additional regulations; emergency response regulations; moratoriums on power plant construction and siting; radiation safety and control studies; and remedial action studies. The collected information is abstracted, indexed, and input into one of the two data bases developed under this information system - Current Legislation Data Base and Historical Legislation Data Base. An appendix is included which provides a summary of the state and local laws affecting the transportation of radioactive materials throughout the United States. The Legislative and Regulatory Information System is supported by the Transportation Technology Center located at Sandia National Laboratories, Albuquerque, New Mexico.

Numerical Heat Transfer Studies of a Latent Heat Storage System Containing Nano-Enhanced Phase Change Material

Directory of Open Access Journals (Sweden)

S F Hosseinizadeh

2011-01-01

Full Text Available The heat transfer enhancement in the latent heat thermal energy storage system through dispersion of nanoparticle is reported. The resulting nanoparticle-enhanced phase change materials (NEPCM exhibit enhanced thermal conductivity in comparison to the base material. The effects of nanoparticle volume fraction and some other parameters such as natural convection are studied in terms of solid fraction and the shape of the solid-liquid phase front. It has been found that higher nanoparticle volume fraction result in a larger solid fraction. The present results illustrate that the suspended nanoparticles substantially increase the heat transfer rate and also the nanofluid heat transfer rate increases with an increase in the nanoparticles volume fraction. The increase of the heat release rate of the NEPCM shows its great potential for diverse thermal energy storage application.

40 CFR 1612.3 - Published reports and material contained in the public incident investigation dockets.

Science.gov (United States)

2010-07-01

... 40 Protection of Environment 32 2010-07-01 2010-07-01 false Published reports and material... Published reports and material contained in the public incident investigation dockets. (a) Demands for published investigation reports should be directed to the Office of Congressional and Public Affairs, U.S...

Materials considerations for molten salt accelerator-based plutonium conversion systems

International Nuclear Information System (INIS)

DiStefano, J.R.; DeVan, J.H.; Keiser, J.R.; Klueh, R.L.; Eatherly, W.P.

1995-03-01

Accelerator-driven transmutation technology (ADTT) refers to a concept for a system that uses a blanket assembly driven by a source of neutrons produced when high-energy protons from an accelerator strike a heavy metal target. One application for such a system is called Accelerator-Based Plutonium Conversion, or ABC. Currently, the version of this concept being proposed by the Los Alamos National Laboratory features a liquid lead target material and a blanket fuel of molten fluorides that contain plutonium. Thus, the materials to be used in such a system must have, in addition to adequate mechanical strength, corrosion resistance to molten lead, corrosion resistance to molten fluoride salts, and resistance to radiation damage. In this report the corrosion properties of liquid lead and the LiF-BeF 2 molten salt system are reviewed in the context of candidate materials for the above application. Background information has been drawn from extensive past studies. The system operating temperature, type of protective environment, and oxidation potential of the salt are shown to be critical design considerations. Factors such as the generation of fission products and transmutation of salt components also significantly affect corrosion behavior, and procedures for inhibiting their effects are discussed. In view of the potential for extreme conditions relative to neutron fluxes and energies that can occur in an ADTT, a knowledge of radiation effects is a most important factor. Present information for potential materials selections is summarized

Materials considerations for molten salt accelerator-based plutonium conversion systems

International Nuclear Information System (INIS)

DiStefano, J.R.; DeVan, J.H.; Keiser, J.R.; Klueh, R.L.; Eatherly, W.P.

1995-02-01

Accelerator-driven transmutation technology (ADTT) refers to a concept for a system that uses a blanket assembly driven by a source of neutrons produced when high-energy protons from an accelerator strike a heavy metal target. One application for such a system is called Accelerator-Based Plutonium Conversion, or ABC. Currently, the version of this concept being proposed by the Los Alamos National Laboratory features a liquid lead target material and a blanket fuel of molten fluorides that contain plutonium. Thus, the materials to be used in such a system must have, in addition to adequate mechanical strength, corrosion resistance to molten lead, corrosion resistance to molten fluoride salts, and resistance to radiation damage. In this report the corrosion properties of liquid lead and the LiF-BeF 2 molten salt system are reviewed in the context of candidate materials for the above application. Background information has been drawn from extensive past studies. The system operating temperature, type of protective environment, and oxidation potential of the salt are shown to be critical design considerations. Factors such as the generation of fission products and transmutation of salt components also significantly affect corrosion behavior, and procedures for inhibiting their effects are discussed. In view of the potential for extreme conditions relative to neutron fluxes and energies that can occur in an ADTT, a knowledge of radiation effects is a most important factor. Present information for potential materials selections is summarized

An examination of source material requirements contained in 10 CFR Part 40

International Nuclear Information System (INIS)

Nussbaumer, D.; Smith, D.A.; Wiblin, C.

1992-10-01

This report identifies issues for consideration for rule-making to update the requirements for source material in 10 CFR Part 40 and examines options for resolving these issues. The contemplated rulemaking is intended to update 10 CFR Part 40 to reflect current radiation protection principles and regulatory practices. It is expected that such an update would make requirements for the control of source material more comparable to those pertaining to byproduct material contained in 10 CFR Part 30. The newer biological data and dose calculation methodology reflected in revised 10 CFR Part 20 will be used in analyses of potential regulatory amendments. This report presents historical background information and discussion on the various issues identified and makes preliminary recommendations concerning needed regulatory changes and approaches to rulemaking

Passive containment system for a nuclear reactor

International Nuclear Information System (INIS)

Kleimola, F.W.

1976-01-01

A containment system is described that provides complete protection entirely by passive means for the loss of coolant accident in a nuclear power plant and wherein all stored energy released in the coolant blowdown is contained and absorbed while the nuclear fuel is continuously maintained submerged in liquid. The primary containment vessel is restored to a high subatmospheric pressure within a few minutes after accident initiation and the decay heat is safely transferred to the environment while radiolytic hydrogen is contained by passive means

A sensor-based automation system for handling nuclear materials

International Nuclear Information System (INIS)

Drotning, W.; Kimberly, H.; Wapman, W.; Darras, D.

1997-01-01

An automated system is being developed for handling large payloads of radioactive nuclear materials in an analytical laboratory. The automation system performs unpacking and repacking of payloads from shipping and storage containers, and delivery of the payloads to the stations in the laboratory. The system uses machine vision and force/torque sensing to provide sensor-based control of the automation system in order to enhance system safety, flexibility, and robustness, and achieve easy remote operation. The automation system also controls the operation of the laboratory measurement systems and the coordination of them with the robotic system. Particular attention has been given to system design features and analytical methods that provide an enhanced level of operational safety. Independent mechanical gripper interlock and tool release mechanisms were designed to prevent payload mishandling. An extensive Failure Modes and Effects Analysis of the automation system was developed as a safety design analysis tool

Nuclear Material Control and Accountability System Effectiveness Tool (MSET)

International Nuclear Information System (INIS)

Powell, Danny H.; Elwood, Robert H. Jr.; Roche, Charles T.; Campbell, Billy J.; Hammond, Glenn A.; Meppen, Bruce W.; Brown, Richard F.

2011-01-01

A nuclear material control and accountability (MC and A) system effectiveness tool (MSET) has been developed in the United States for use in evaluating material protection, control, and accountability (MPC and A) systems in nuclear facilities. The project was commissioned by the National Nuclear Security Administration's Office of International Material Protection and Cooperation. MSET was developed by personnel with experience spanning more than six decades in both the U.S. and international nuclear programs and with experience in probabilistic risk assessment (PRA) in the nuclear power industry. MSET offers significant potential benefits for improving nuclear safeguards and security in any nation with a nuclear program. MSET provides a design basis for developing an MC and A system at a nuclear facility that functions to protect against insider theft or diversion of nuclear materials. MSET analyzes the system and identifies several risk importance factors that show where sustainability is essential for optimal performance and where performance degradation has the greatest impact on total system risk. MSET contains five major components: (1) A functional model that shows how to design, build, implement, and operate a robust nuclear MC and A system (2) A fault tree of the operating MC and A system that adapts PRA methodology to analyze system effectiveness and give a relative risk of failure assessment of the system (3) A questionnaire used to document the facility's current MPC and A system (provides data to evaluate the quality of the system and the level of performance of each basic task performed throughout the material balance area (MBA)) (4) A formal process of applying expert judgment to convert the facility questionnaire data into numeric values representing the performance level of each basic event for use in the fault tree risk assessment calculations (5) PRA software that performs the fault tree risk assessment calculations and produces risk importance

Thermal hydraulic analysis of BWR containment venting system

International Nuclear Information System (INIS)

Baburajan, P.K.; Sharma, Prashant; Paul, U.K.; Gaikwad, Avinash

2015-01-01

Installation of additional containment filtered venting system (CFVS) is necessary to depressurize the containment to maintain its mechanical integrity due to over pressurization during severe accident condition. A typical venting system for BWR is modelled using RELAP5 and analysed to investigate the effect of various thermal hydraulic parameters on the operational parameters of the venting system. The venting system consists of piping from the containment to the scrubber tank and exit line from the scrubber tank. The scrubber tank is partially filled with water to enable the scrubbing action to remove the particulate radionuclides from the incoming containment air. The pipe line from the containment is connected to the venturi inlet and the throat of the venturi is open to the scrubber tank water inventory at designed submergence level. The exit of the venturi is open to scrubber tank water. Filters are used in the upper air space of the scrubber tank as mist separator before venting out the air into the atmosphere through the exit vent line. The effect of thermal hydraulic parameters such as inlet fluid temperature, inlet steam content and venturi submergence in the scrubber tank on the venting flow rate, exit steam content, scrubber tank inventory, overflow line and siphon breaker flow rate is analysed. Results show that inlet steam content and the venturi nozzle submergence influence the venting system parameters. (author)

A data communications systems for tamper-protected special nuclear materials (SNM) inventory management

International Nuclear Information System (INIS)

Hurkamp, A.C.

1995-01-01

The Department of Energy (D.O.E.) is responsible for the long term storage and protection of large quantities of Special Nuclear Material (SNM). This material is stored within individual containers located in vaults. Security measures are required to ensure that the SNM remains within the canisters where it is stored and that it is not disturbed in any manner. Conventional security and inventory techniques are manpower intensive and often require exposure to radiation hazards. The Purpose of this D.O.E sponsored project is to develop a cost effective system to monitor Special Nuclear Materials that, when fielded, would result in an extension of manual inventory cycles at a wide variety of SNM storage locations. The system consists of a computer, radio frequency interrogator, and individual miniaturized radio frequency transponders (tags) that are co-located with individual SNM containers. Each tag can perform SNM inventory, tamper alarm, and multiple sensor data transmission to the interrogator under the control of software designed by the user. SNM custodians can customize the system by their choice of packaging, software, and sensors. When implemented in accordance with current department of energy (D.O.E.) Policy on SNM inventory extension, the system has the potential to qualify for maximum extension times thus saving considerable resources through reduction of radiation exposure

Reliability analysis of containment isolation systems

International Nuclear Information System (INIS)

Pelto, P.J.; Ames, K.R.; Gallucci, R.H.

1985-06-01

This report summarizes the results of the Reliability Analysis of Containment Isolation System Project. Work was performed in five basic areas: design review, operating experience review, related research review, generic analysis and plant specific analysis. Licensee Event Reports (LERs) and Integrated Leak Rate Test (ILRT) reports provided the major sources of containment performance information used in this study. Data extracted from LERs were assembled into a computer data base. Qualitative and quantitative information developed for containment performance under normal operating conditions and design basis accidents indicate that there is room for improvement. A rough estimate of overall containment unavailability for relatively small leaks which violate plant technical specifications is 0.3. An estimate of containment unavailability due to large leakage events is in the range of 0.001 to 0.01. These estimates are dependent on several assumptions (particularly on event duration times) which are documented in the report

Transport containers for radioactive material

International Nuclear Information System (INIS)

Bibby, D.

1978-01-01

A transport container for transporting irradiated nuclear fuel is described comprising a steel flask with detachable cover and having external heat exchange fins. The flask contains a solid annular shield comprised of discrete bodies of Pb or Fe bonded together by a solid matrix, for attenuating gamma rays and neutron emission. This may comprise lead shot bonded together by concrete or polyethylene, or alternatively iron shot bonded by concrete. (UK)

Comparative analysis of non-destructive methods to control fissile materials in large-size containers

Directory of Open Access Journals (Sweden)

Batyaev V.F.

2017-01-01

Full Text Available The analysis of various non-destructive methods to control fissile materials (FM in large-size containers filled with radioactive waste (RAW has been carried out. The difficulty of applying passive gamma-neutron monitoring FM in large containers filled with concreted RAW is shown. Selection of an active non-destructive assay technique depends on the container contents; and in case of a concrete or iron matrix with very low activity and low activity RAW the neutron radiation method appears to be more preferable as compared with the photonuclear one.

ENGINEERING CONTROL PRACTICES FOR REDUCING EMISSIONS DURING DRILLING OF ASBESTOS-CONTAINING FLOORING MATERIALS

Science.gov (United States)

This report describes the implementation and testing of control measures to reduce airborne asbestos generated by the drilling of asbestos-containing flooring materials, an OSHA Class III asbestos maintenance activity. Bosch 11224 and 11222 rotary drills were fitted with shrouds ...

76 FR 41178 - Pesticides; Policies Concerning Products Containing Nanoscale Materials; Opportunity for Public...

Science.gov (United States)

2011-07-13

... Pesticides; Policies Concerning Products Containing Nanoscale Materials; Opportunity for Public Comment; Extension of Comment Period AGENCY: Environmental Protection Agency (EPA). ACTION: Proposed policy statement; extension of comment period. SUMMARY: EPA issued a proposed policy statement in the Federal Register of June...

Tracer verification and monitoring of containment systems

International Nuclear Information System (INIS)

Lowry, W.; Dunn, S.D.; Williams, C.

1996-01-01

In-situ barrier emplacement techniques and materials for the containment of high-risk contaminants in soils are currently being developed by the Department of Energy (DOE). Because of their relatively high cost, the barriers are intended to be used in cases where the risk is too great to remove the contaminants, the contaminants are too difficult to remove with current technologies, or the potential for movement of the contaminants to the water table is so high that immediate action needs to be taken to reduce health risks. Consequently, barriers are primarily intended for use in high-risk sites where few viable alternatives exist to stop the movement of contaminants in the near term. Assessing the integrity of the barrier once it is emplaced, and during its anticipated life, is a very difficult but necessary requirement. Existing surface-based and borehole geophysical techniques do not provide the degree of resolution required to assure the formation of an integral in-situ barrier. Science and Engineering Associates, Inc., (SEA) and Sandia National Laboratories (SNL) are developing a quantitative subsurface barrier assessment system using gaseous tracers. Called SEAtrace trademark, this system integrates an autonomous, multipoint soil vapor sampling and analysis system with a global optimization modeling methodology to pinpoint leak sources and sizes in real time. SEAtrace trademark is applicable to impermeable barrier emplacements above the water table, providing a conservative assessment of barrier integrity after emplacement, as well as a long term integrity monitoring function. The SEAtrace trademark system is being developed under funding by the DOE-EM Subsurface Contaminant Focus Area

Numerical Simulation on Dense Packing of Granular Materials by Container Oscillation

Directory of Open Access Journals (Sweden)

Jun Liu

2013-01-01

Full Text Available The packing of granular materials is a basic and important problem in geomechanics. An approach, which generates dense packing of spheres confined in cylindrical and cuboidal containers in three steps, is introduced in this work. A loose packing structure is first generated by means of a reference lattice method. Then a dense packing structure is obtained in a container by simulating dropping of particles under gravitational forces. Furthermore, a scheme that makes the bottom boundary fluctuate up and down was applied to obtain more denser packing. The discrete element method (DEM was employed to simulate the interactions between particle-particle and particle-boundary during the particles' motions. Finally, two cases were presented to indicate the validity of the method proposed in this work.

Material control system simulator user's manual

International Nuclear Information System (INIS)

Hollstien, R.B.

1978-01-01

This report describes the use of a Material Control System Simulator (MCSS) program for determination of material accounting uncertainty and system response to particular adversary action sequences that constitute plausible material diversion attempts. The program is intended for use in situations where randomness, uncertainty, or interaction of adversary actions and material control system components make it difficult to assess safeguards effectiveness against particular material diversion attempts

Adapting to Biology: Maintaining Container-Closure System Compatibility with the Therapeutic Biologic Revolution.

Science.gov (United States)

Degrazio, Dominick

Many pharmaceutical companies are transitioning their research and development drug product pipeline from traditional small-molecule injectables to the dimension of evolving therapeutic biologics. Important concerns associated with this changeover are becoming forefront, as challenges develop of varying complexity uncommon with the synthesis and production of traditional drugs. Therefore, alternative measures must be established that aim to preserve the efficacy and functionality of a biologic that might not be implemented for small molecules. Conserving protein stability is relative to perpetuating a net equilibrium of both intrinsic and extrinsic factors. Key to sustaining this balance is the ability of container-closure systems to maintain their compatibility with the ever-changing dynamics of therapeutic biologics. Failure to recognize and adjust the material properties of packaging components to support compatibility with therapeutic biologics can compromise patient safety, drug productivity, and biological stability. This review will examine the differences between small-molecule drugs and therapeutic biologics, lay a basic foundation for understanding the stability of therapeutic biologics, and demonstrate potential sources of container-closure systems' incompatibilities with therapeutic biologics at a mechanistic level. Many pharmaceutical companies are transitioning their research and development drug product pipeline from traditional small-molecule injectables to recombinantly derived therapeutic biologics. Concerns associated with this transformation are becoming prominent, as therapeutic biologics are uncharacteristic to small-molecule drugs. Maintaining the stability of a therapeutic biologic is a combination of balancing intrinsic factors and external elements within the biologic's microenvironment. An important aspect of this balance is relegated to the overall compatibility of primary, parenteral container-closure systems with therapeutic biologics

Permanent monitoring of containment integrity: the sexten system

International Nuclear Information System (INIS)

Germain, J.L.; Janneteau, E.

1993-01-01

Reactor containment integrity is of prime importance to the safety of PWR units. It is checked by means of tests performed at high pressure during the containment building pressure tests. These periodical tests are supplemented in France by permanent monitoring using the SEXTEN system. First feasibility tests for this system were carried out in 1980. The encouraging results obtained led to the development of a prototype, followed by an industrial system which has since been installed in all French PWR units. This system measures the containment leak rate, with corrections for the compressed air intakes used by the air-operated valves. Leaktightness is expressed in terms of the leak rate for a 60 mbar overpressure. If the leak rate exceeds a fixed limit value, leak detection operations are initiated, using SEXTEN. A new version of the system, known as SEXTEN 2 is being developed. (authors). 2 figs

AP600 containment purge radiological analysis

Energy Technology Data Exchange (ETDEWEB)

O`Connor, M.; Schulz, J.; Tan, C. [Bechtel Power Corporation (United States)] [and others

1995-02-01

The AP600 Project is a passive pressurized water reactor power plant which is part of the Design Certification and First-of-a-Kind Engineering effort under the Advanced Light Water Reactor program. Included in this process is the design of the containment air filtration system which will be the subject of this paper. We will compare the practice used by previous plants with the AP600 approach to meet the goals of industry standards in sizing the containment air filtration system. The radiological aspects of design are of primary significance and will be the focus of this paper. The AP600 Project optimized the design to combine the functions of the high volumetric flow rate, low volumetric flow rate, and containment cleanup and other filtration systems into one multi-functional system. This achieves a more simplified, standardized, and lower cost design. Studies were performed to determine the possible concentrations of radioactive material in the containment atmosphere and the effectiveness of the purge system to keep concentrations within 10CFR20 limits and within offsite dose objectives. The concentrations were determined for various reactor coolant system leakage rates and containment purge modes of operation. The resultant concentrations were used to determine the containment accessibility during various stages of normal plant operation including refueling. The results of the parametric studies indicate that a dual train purge system with a capacity of 4,000 cfm per train is more than adequate to control the airborne radioactivity levels inside containment during normal plant operation and refueling, and satisfies the goals of ANSI/ANS-56.6-1986 and limits the amount of radioactive material released to the environment per ANSI/ANS 59.2-1985 to provide a safe environment for plant personnel and offsite residents.

Reactor container

International Nuclear Information System (INIS)

Ichiki, Tadaharu; Saba, Kazuhisa.

1979-01-01

Purpose: To improve the earthquake resistance as well as reduce the size of a container for a nuclear reactor with no adverse effects on the decrease of impact shock to the container and shortening of construction step. Constitution: Reinforcing profile steel materials are welded longitudinally and transversely to the inner surface of a container, and inner steel plates are secured to the above profile steel materials while keeping a gap between the materials and the container. Reactor shielding wall planted to the base concrete of the container is mounted to the pressure vessel, and main steam pipeways secured by the transverse beams and led to the outside of container is connected. This can improve the rigidity earthquake strength and the safetiness against the increase in the inside pressure upon failures of the container. (Yoshino, Y.)

Evaluation of iron-base materials for waste package containers in a salt repository

International Nuclear Information System (INIS)

Westerman, R.E.; Nelson, J.L.; Kuhn, W.L.; Basham, S.G.; Moak, D.A.; Pitman, S.G.

1983-11-01

Design studies for high-level nuclear waste packages for salt repositories have identified low-carbon steel as a candidate material for containers. Among the requirements are strength, corrosion resistance, and fabricability. The studies of the corrosion resistance and structural stability of iron-base materials (particularly low-carbon steel) are treated in this paper. The materials have been exposed in brines that are characteristic of the potential sites for salt repositories. The effects of temperature, radiation level, oxygen level and other parameters are under investigation. The initial development of corrosion models for these environments is presented with discussion of the key mechanisms under consideration. 6 references, 5 figures

The management system for the safe transport of radioactive material. Safety guide

International Nuclear Information System (INIS)

2008-01-01

The purpose of this Safety Guide is to provide information to organizations that are developing, implementing or assessing a management system for activities relating to the transport of radioactive material. Such activities include, but are not limited to, design, fabrication, inspection and testing, maintenance, transport and disposal of radioactive material packaging. This publication is intended to assist those establishing or improving a management system to integrate safety, health, environmental, security, quality and economic elements to ensure that safety is properly taken into account in all activities of the organization. Contents: 1. Introduction; 2. Management system; 3. Management responsibility; 4. Resource management; 5. Process implementation; 6. Measurement, assessment and improvement; Appendix: Graded approach for management systems for the safe transport of radioactive materials; Annex I: Two examples of management systems; Annex II: Examples of management system standards; Annex III: Example of a documented management system (or quality assurance programme) for an infrequent consignor; Annex IV: Example of a documented management system (or quality assurance programme) description for an infrequent carrier; Annex V: Example of a procedure for control of records; Annex VI: Example of a procedure for handling packages containing radioactive materials, including receipt and dispatch; Annex VII: Example of a packaging maintenance procedure in a complex organization; Annex VIII: Example of an internal audit procedure in a small organization; Annex IX: Example of a corrective and preventive action procedure

Materials management information systems.

Science.gov (United States)

1996-01-01

The hospital materials management function--ensuring that goods and services get from a source to an end user--encompasses many areas of the hospital and can significantly affect hospital costs. Performing this function in a manner that will keep costs down and ensure adequate cash flow requires effective management of a large amount of information from a variety of sources. To effectively coordinate such information, most hospitals have implemented some form of materials management information system (MMIS). These systems can be used to automate or facilitate functions such as purchasing, accounting, inventory management, and patient supply charges. In this study, we evaluated seven MMISs from seven vendors, focusing on the functional capabilities of each system and the quality of the service and support provided by the vendor. This Evaluation is intended to (1) assist hospitals purchasing an MMIS by educating materials managers about the capabilities, benefits, and limitations of MMISs and (2) educate clinical engineers and information system managers about the scope of materials management within a healthcare facility. Because software products cannot be evaluated in the same manner as most devices typically included in Health Devices Evaluations, our standard Evaluation protocol was not applicable for this technology. Instead, we based our ratings on our observations (e.g., during site visits), interviews we conducted with current users of each system, and information provided by the vendor (e.g., in response to a request for information [RFI]). We divided the Evaluation into the following sections: Section 1. Responsibilities and Information Requirements of Materials Management: Provides an overview of typical materials management functions and describes the capabilities, benefits, and limitations of MMISs. Also includes the supplementary article, "Inventory Cost and Reimbursement Issues" and the glossary, "Materials Management Terminology." Section 2. The

Preliminary analysis of the creep behaviour of nuclear fuel-waste container materials

International Nuclear Information System (INIS)

Dutton, R.; Leitch, B.W.; Crosthwaite, J.L.; Kasprick, G.R.

1996-12-01

In the Canadian Nuclear Fuel Waste Management Program, it is proposed that nuclear fuel waste be placed in a durable container and disposed of in a deep underground vault. Consideration of various disposal-container designs has identified either titanium or copper as the material suitable for constructing the container shell. As part of the R and D program to examine the structural integrity of the container, creep tests are being conducted on commercially pure titanium and oxygen-free copper. This report presents the preliminary data obtained. It also describes the evaluation of various constitutive equations to represent the creep curves, thus providing the basis for extrapolation of the creep behaviour over the design lifetime of the container. In this regard, a specific focus is placed on equations derived from the 0-Projection Concept. Recognizing that the container lifetime will be determined by the onset of tertiary creep leading to creep rupture, we present the results of the metallographic examination of creep damage. This shows that the tertiary stage in titanium is associated with the formation of transgranular cavities within the region of localized necking of the creep specimens. In contrast, creep damage in copper is in the form of intergranular cavities uniformly distributed throughout the gauge length. These results are analyzed within the context of the extant literature, and their implications for future container design are discussed. (author)

41 CFR 101-42.1101 - Federal supply classification (FSC) groups and classes which contain hazardous materials.

Science.gov (United States)

2010-07-01

..., building paper, and thermal insulation materials Asbestos cloth which has loose fibers or particles that... shipment. 5965 Headsets, handsets, microphones, and speakers Items containing magnetic material. 5970... hazardous chemicals, solvents. 6625 Electrical and electronic properties measuring and testing instruments...

Life cycle assessment of façade coating systems containing manufactured nanomaterials

Energy Technology Data Exchange (ETDEWEB)

Hischier, Roland, E-mail: roland.hischier@empa.ch; Nowack, Bernd [Swiss Federal Laboratories for Materials Science and Technology (Empa), Technology and Society Lab (TSL) (Switzerland); Gottschalk, Fadri [ETSS (Switzerland); Hincapie, Ingrid [Swiss Federal Laboratories for Materials Science and Technology (Empa), Technology and Society Lab (TSL) (Switzerland); Steinfeldt, Michael [University of Bremen FB 4/FG 10 Technological Design and Development (Germany); Som, Claudia [Swiss Federal Laboratories for Materials Science and Technology (Empa), Technology and Society Lab (TSL) (Switzerland)

2015-02-15

Nanotechnologies are expected to hold considerable potential for the development of new materials in the construction sector. Up to now the environmental benefits and risks of products containing manufactured nanomaterials (MNM) have been quantified only to a limited extent. This study aims to assess the potential environmental, health and safety impacts of coatings containing MNM using Life-cycle assessment: Do paints containing MNM result in a better environmental performance than paints not containing MNM? The study shows that the results depend on a number of factors: (i) The MNM have to substitute an (active) ingredient of the initial paint composition and not simply be an additional ingredient. (ii) The new composition has to extend the lifetime of the paint for such a time period that the consumption of paint along the life cycle of a building is reduced. (iii) Releases of MNM have to be reduced to the lowest level possible (in particular by dumping unused paint together with the packaging). Only when all these boundary conditions are fulfilled, which is the case only for one of the three paint systems examined, is an improved environmental performance of the MNM-containing paint possible for the paint compositions examined in this study.

[Experimental study of percutaneous vertebroplasty with a novel bone void filling container system].

Science.gov (United States)

Wang, Tai-Ping; Zhang, Kui-bo; Zheng, Zhao-min; Liu, Hui; Yu, Bin-sheng

2011-04-19

To investigate vertebral augmentation with a novel reticulate bone filling container system by polymethyl methacrylate (PMMA) injection in cadaveric simulated vertebral compressive fracture and explore the effect of reticulate bone filling container on cement distribution controlling within vertebral body and the restoration of biomechanical properties after augmentation. A total of 28 freshly frozen human vertebrae specimens were randomly divided into 4 groups. After the measurements of bone mineral density (BMD) and vertebral height, each vertebra received an axle load by a MTS (material testing system) machine to test the initial strength and stiffness. Subsequently a simultaneous compressive fracture model was created to measure the stiffness and height of fractured vertebrae. Then the augmentation procedure was performed. Afterward the biomechanical properties and the vertebral height were similarly measured as pre-operatively. The expansion of bone filling container and the distribution of cement within vertebral body were morphologically observed by crossing the specimens in sagittal midline and also integrated with the radiographic results. Stiffness was significantly restored comparing with that of fractured level (P container groups while it was irregular in single-layer groups. After crossing, the double-layer version expanded well in vertebral body and could enwrap most of injected cement. There was only a little leakage near the vessel layer. But the single-layer version had a poor expansion and a large amount of cement leakage. This novel reticulate bone void filling container system with different layers may restore both the biomechanical properties and the height of fractured vertebrae. But, with the benefit of reducing cement leakage, a double-layer design can enwrap most of injected PMMA and has a brighter prospect of clinical application.

Smart container UWB sensor system for situational awareness of intrusion alarms

Science.gov (United States)

Romero, Carlos E.; Haugen, Peter C.; Zumstein, James M.; Leach, Jr., Richard R.; Vigars, Mark L.

2013-06-11

An in-container monitoring sensor system is based on an UWB radar intrusion detector positioned in a container and having a range gate set to the farthest wall of the container from the detector. Multipath reflections within the container make every point on or in the container appear to be at the range gate, allowing intrusion detection anywhere in the container. The system also includes other sensors to provide false alarm discrimination, and may include other sensors to monitor other parameters, e.g. radiation. The sensor system also includes a control subsystem for controlling system operation. Communications and information extraction capability may also be included. A method of detecting intrusion into a container uses UWB radar, and may also include false alarm discrimination. A secure container has an UWB based monitoring system

Evaluation of the nucledyne passive containment system

International Nuclear Information System (INIS)

1981-04-01

This reports contains: (1) an evaluation by Gilbert/Commonwealth (G/C) of the NucleDyne passive Containment System (PCS) as that conceptual design is applied to a Westinghouse, two loop, Pressurized Water Reactor; (2) an evaluation by Westinghouse of two questions about the impact of the PCS on the Nuclear Steam Supply System (NSSS), which were posed by G/C and best answered by an NSSS vendor; and (3) replies to both the Gilbert/Commonwealth report and the Westinghoue report by NucleDyne Engineering Corporation

Nupack, the new Asme code for radioactive material transportation packaging containments

International Nuclear Information System (INIS)

Turula, P.

1998-01-01

The American Society of Mechanical Engineers (ASME) has added a new division to the nuclear construction section of its Boiler and Pressure Vessel Code (B and PVC). This Division, commonly referred to as 'Nupack', has been written to provide a consistent set of technical requirements for containment vessels of transportation packagings for high-level radioactive materials. This paper provides an introduction to Nupack, discusses some of its technical provisions, and describes how it can be used the design and construction of packaging components. Nupack's general provisions and design requirements are emphasized, while treatment of materials, fabrication and inspection is left for another paper. Participation in the Nupack development work described in this paper was supported by the U.S. Department of Energy. (authors)

Verification of the burn-up of spent fuel assemblies by means of the Consulha containment/surveillance system

International Nuclear Information System (INIS)

Daniel, G.; Gourlez, P.

1991-01-01

CONSULHA is a containment/surveillance system which has been developed as part of the French Support Programme for the IAEA Safeguards in cooperation with EURATOM and was designed to meet the IAEA EURATOM requirements for the verification of nuclear materials. This system will make it possible to count movements and verify irradiation of spent fuel assemblies in industrial facilities such as reprocessing plants and nuclear reactors

Modernizing computerized nuclear material accounting systems

International Nuclear Information System (INIS)

Erkkila, B.H.; Claborn, J.

1995-01-01

DOE Orders and draft orders for nuclear material control and accountability address a complete material control and accountability (MC and A) program for all DOE contractors processing, using, or storing nuclear materials. A critical element of an MC and A program is the accounting system used to track and record all inventories of nuclear material and movements of materials in those inventories. Most DOE facilities use computerized accounting systems to facilitate the task of accounting for all their inventory of nuclear materials. Many facilities still use a mixture of a manual paper system with a computerized system. Also, facilities may use multiple systems to support information needed for MC and A. For real-time accounting it is desirable to implement a single integrated data base management system for a variety of users. In addition to accountability needs, waste management, material management, and production operations must be supported. Information in these systems can also support criticality safety and other safety issues. Modern networked microcomputers provide extensive processing and reporting capabilities that single mainframe computer systems struggle with. This paper describes an approach being developed at Los Alamos to address these problems

Experimental analysis of a low cost phase change material emulsion for its use as thermal storage system

International Nuclear Information System (INIS)

Delgado, Mónica; Lázaro, Ana; Mazo, Javier; Peñalosa, Conchita; Dolado, Pablo; Zalba, Belén

2015-01-01

Highlights: • A low cost PCM emulsion has been analyzed as thermal energy storage system. • Its thermophysical and rheological properties have been determined. • The system shows advantages in terms of energy density and heat transfer rate. • The PCM emulsion system has been compared to other thermal energy storage systems. - Abstract: A 46 l commercial tank with a helical coil heat exchanger and containing a low cost phase change material emulsion has been experimentally analyzed as a thermal energy storage system in terms of volumetric energy density and heat transfer rate, for its subsequent comparison with other thermal energy storage systems. This phase change material emulsion shows a phase change temperature range between 30 and 50 °C, its solids content is about 60% with an average particle size of 1 μm. The low cost phase change material emulsion shows a thermal storage capacity by mass 50% higher than water and an increase in viscosity up to 2–5 orders of magnitude. The results have shown that the global heat transfer coefficient of the phase change material emulsion tank is around 2–6 times higher than for conventional latent systems previously analyzed in literature, although 5 times lower than if it contains water. The phase change material emulsion tank presents an energy density 34% higher than the water tank, which makes it a promising solution. Measures to improve its performance are also studied in this work.

Evaluation of calculational and material models for concrete containment structures

International Nuclear Information System (INIS)

Dunham, R.S.; Rashid, Y.R.; Yuan, K.A.

1984-01-01

A computer code utilizing an appropriate finite element, material and constitutive model has been under development as a part of a comprehensive effort by the Electric Power Research Institute (EPRI) to develop and validate a realistic methodology for the ultimate load analysis of concrete containment structures. A preliminary evaluation of the reinforced and prestressed concrete modeling capabilities recently implemented in the ABAQUS-EPGEN code has been completed. This effort focuses on using a state-of-the-art calculational model to predict the behavior of large-scale reinforced concrete slabs tested under uniaxial and biaxial tension to simulate the wall of a typical concrete containment structure under internal pressure. This paper gives comparisons between calculations and experimental measurements for a uniaxially-loaded specimen. The calculated strains compare well with the measured strains in the reinforcing steel; however, the calculations gave diffused cracking patterns that do not agree with the discrete cracking observed in the experiments. Recommendations for improvement of the calculational models are given. (orig.)

Design of database management system for 60Co container inspection system

International Nuclear Information System (INIS)

Liu Jinhui; Wu Zhifang

2007-01-01

The function of the database management system has been designed according to the features of cobalt-60 container inspection system. And the software related to the function has been constructed. The database querying and searching are included in the software. The database operation program is constructed based on Microsoft SQL server and Visual C ++ under Windows 2000. The software realizes database querying, image and graph displaying, statistic, report form and its printing, interface designing, etc. The software is powerful and flexible for operation and information querying. And it has been successfully used in the real database management system of cobalt-60 container inspection system. (authors)

Material control system simulator program reference manual

Energy Technology Data Exchange (ETDEWEB)

Hollstien, R.B.

1978-01-24

A description is presented of a Material Control System Simulator (MCSS) program for determination of material accounting uncertainty and system response to particular adversary action sequences that constitute plausible material diversion attempts. The program is intended for use in situations where randomness, uncertainty, or interaction of adversary actions and material control system components make it difficult to assess safeguards effectiveness against particular material diversion attempts. Although MCSS may be used independently in the design or analysis of material handling and processing systems, it has been tailored toward the determination of material accountability and the response of material control systems to adversary action sequences.

Material control system simulator program reference manual

International Nuclear Information System (INIS)

Hollstien, R.B.

1978-01-01

A description is presented of a Material Control System Simulator (MCSS) program for determination of material accounting uncertainty and system response to particular adversary action sequences that constitute plausible material diversion attempts. The program is intended for use in situations where randomness, uncertainty, or interaction of adversary actions and material control system components make it difficult to assess safeguards effectiveness against particular material diversion attempts. Although MCSS may be used independently in the design or analysis of material handling and processing systems, it has been tailored toward the determination of material accountability and the response of material control systems to adversary action sequences

Comparative analysis of non-destructive methods to control fissile materials in large-size containers

Science.gov (United States)

Batyaev, V. F.; Sklyarov, S. V.

2017-09-01

The analysis of various non-destructive methods to control fissile materials (FM) in large-size containers filled with radioactive waste (RAW) has been carried out. The difficulty of applying passive gamma-neutron monitoring FM in large containers filled with concreted RAW is shown. Selection of an active non-destructive assay technique depends on the container contents; and in case of a concrete or iron matrix with very low activity and low activity RAW the neutron radiation method appears to be more preferable as compared with the photonuclear one. Note to the reader: the pdf file has been changed on September 22, 2017.

The Inventory of Interstellar Materials Available for the Formation of the Solar System

Science.gov (United States)

Sandford, Scott A.; Witteborn, Fred C. (Technical Monitor)

1996-01-01

Dr. Derek Sears, the editor of the journal Meteoritics and Planetary Science, has established a policy of having each issue of the journal contain an invited review of an area that he deems to be of special cur-rent importance. Typically 20 to 25 pages of the beginning of the journal are devoted to each review. He has asked me to prepare such a review summarizing what we know about the composition and structure of interstellar materials. The attached paper is the result. This is a good time for such a review since tremendous progress has been made in the field of interstellar dust in recent years through the use of telescopic observations, theoretical studies, laboratory studies of analogs, and the study of actual interstellar samples found in meteorites. It is increasing clear that the interstellar medium (ISM) contains an enormous diversity of materials created by a wide range of chemical and physical processes. This understanding is a far cry from the picture of interstellar materials held as recently as two decades ago, a picture which incorporated only a few generic types of grains and few molecules. In the paper I review our current knowledge of the more abundant materials thought to exist in the ISM. The review concentrates on matter in interstellar dense molecular clouds since it is the materials in these environments from which new stars and planetary systems are formed, although materials in circumstellar environments and in the diffuse ISM are also discussed. The paper focuses largely on solid materials since they contain a major fraction of the heavier elements in clouds and because solids are most likely to survive incorporation into new planetary systems in identifiable form. The paper concludes with discussion of some of the implications resulting from the identification of these interstellar materials. I also present some new thoughts, the most intriguing being that meteoritic 'microdiamonds' may be the same material that modelers of the