Potential problems from shipment of high-curie content contact-handled transuranic (CH-TRU) waste to WIPP

International Nuclear Information System (INIS)

Neill, R.H.; Channell, J.K.

1983-08-01

There are about 1000 drums of contact-handled transuranic (CH-TRU) wastes containing more than 100 Ci/drum of Pu-238 that are stored at the Savannah River Plant and at the Los Alamos National Laboratory. Studies performed at DOE laboratories have shown that large quantities of gases are generated in stored drums containing 100 Ci of 238 Pu. Concentrations of hydrogen gas in the void space of the drums are often found to be high enough to be explosive. None of the analyses in the DOE WIPP Final Environmental Impact Statement, Safety Analysis Report, and Preliminary Transportation Analysis have considered the possibility that the generation of hydrogen gas by radiolysis may create an explosive or flammable hazard that could increase the frequency and severity of accidental releases of radionuclides during transportation or handling. These high 238 Pu concentration containers would also increase the estimated doses received by individuals and populations from transportation, WIPP site operations, and human intrusion scenarios even if the possibility of gas-enhanced releases is ignored. The WIPP Project Office has evaluated this effect on WIPP site operations and is suggesting a maximum limit of 140 239 Pu equivalent curies (P-Ci) per drum so that postulated accidental off-site doses will not be larger than those listed in the FEIS. The TRUPACT container, which is being designed for the transportation of CH-TRU wastes to WIPP, does not appear to meet the Nuclear Regulatory Commission regulations requiring double containment for the transportation of plutonium in quantities >20 Ci. A 20 alpha Ci/shipment limit would require about 200,000 shipments for the 4 million curies of alpha emitters slated for WIPP

Results from simulated contact-handled transuranic waste experiments at the Waste Isolation Pilot Plant

International Nuclear Information System (INIS)

Molecke, M.A.; Sorensen, N.R.; Krumhansl, J.L.

1993-01-01

We conducted in situ experiments with nonradioactive, contact-handled transuranic (CH TRU) waste drums at the Waste Isolation Pilot Plant (WIPP) facility for about four years. We performed these tests in two rooms in rock salt, at WIPP, with drums surrounded by crushed salt or 70 wt % salt/30 wt % bentonite clay backfills, or partially submerged in a NaCl brine pool. Air and brine temperatures were maintained at ∼40C. These full-scale (210-L drum) experiments provided in situ data on: backfill material moisture-sorption and physical properties in the presence of brine; waste container corrosion adequacy; and, migration of chemical tracers (nonradioactive actinide and fission product simulants) in the near-field vicinity, all as a function of time. Individual drums, backfill, and brine samples were removed periodically for laboratory evaluations. Waste container testing in the presence of brine and brine-moistened backfill materials served as a severe overtest of long-term conditions that could be anticipated in an actual salt waste repository. We also obtained relevant operational-test emplacement and retrieval experience. All test results are intended to support both the acceptance of actual TRU wastes at the WIPP and performance assessment data needs. We provide an overview and technical data summary focusing on the WIPP CH TRU envirorunental overtests involving 174 waste drums in the presence of backfill materials and the brine pool, with posttest laboratory materials analyses of backfill sorbed-moisture content, CH TRU drum corrosion, tracer migration, and associated test observations

Certification plan transuranic waste: Hazardous Waste Handling Facility

International Nuclear Information System (INIS)

1992-06-01

The purpose of this plan is to describe the organization and methodology for the certification of transuranic (TRU) waste handled in the Hazardous Waste Handling Facility at Lawrence Berkeley Laboratory (LBL). The plan incorporates the applicable elements of waste reduction, which include both up-front minimization and end-product treatment to reduce the volume and toxicity of the waste; segregation of the waste as it applies to certification; an executive summary of the Quality Assurance Implementing Management Plan (QAIMP) for the HWBF; and a list of the current and planned implementing procedures used in waste certification

Concentration of remote-handled, transuranic, sodium nitrate-based sludge using agitated thin-film evaporators

International Nuclear Information System (INIS)

Walker, J.F. Jr.; Youngblood, E.L.; Berry, J.B.; Pen, Ben-Li

1991-01-01

The Waste Handling and Packaging Plant (WHPP) is being designed at Oak Ridge National Laboratory (ORNL) to prepared transuranic waste for final disposal. Once operational, this facility will process, package, and certify remote-handled transuranic waste for ultimate shipment and disposal at the Waste Isolation Pilot Plant (WIPP) in Carlsbad, New Mexico. One of the wastes that will be handled at WHIPP is the transuranic sludge currently stored at ORNL in eight 50,000-gal underground tanks. The use of an Agitated Thin-Film Evaporator (ATFE) for concentration of this waste is being investigated. Tests have shown that the ATFE can be used to produce a thick slurry, a powder, or a fused salt. A computer model developed at the Savannah River Plant (SRP) to simulate the operation of ATFE's on their waste is being modified for use on the ORNL transuranic sludge. This paper summarizes the results of the test with the ATFEs to date, discusses the changes in the SRP model necessary to use this model with the ORNL waste, and compares the results of the model with the actual data taken from the operation of ATFEs at vendors' test facilities. 8 refs., 1 fig., 3 tabs

Unresolved issues for the disposal of remote-handled transuranic waste in the Waste Isolation Pilot Plant

International Nuclear Information System (INIS)

Silva, M.K.; Neill, R.H.

1994-09-01

The purpose of the Waste Isolation Pilot Plant (WIPP) is to dispose of 176,000 cubic meters of transuranic (TRU) waste generated by the defense activities of the US Government. The envisioned inventory contains approximately 6 million cubic feet of contact-handled transuranic (CH TRU) waste and 250,000 cubic feet of remote handled transuranic (RH TRU) waste. CH TRU emits less than 0.2 rem/hr at the container surface. Of the 250,000 cubic feet of RH TRU waste, 5% by volume can emit up to 1,000 rem/hr at the container surface. The remainder of RH TRU waste must emit less than 100 rem/hr. These are major unresolved problems with the intended disposal of RH TRU waste in the WIPP. (1) The WIPP design requires the canisters of RH TRU waste to be emplaced in the walls (ribs) of each repository room. Each room will then be filled with drums of CH TRU waste. However, the RH TRU waste will not be available for shipment and disposal until after several rooms have already been filled with drums of CH TRU waste. RH TRU disposal capacity will be loss for each room that is first filled with CH TRU waste. (2) Complete RH TRU waste characterization data will not be available for performance assessment because the facilities needed for waste handling, waste treatment, waste packaging, and waste characterization do not yet exist. (3) The DOE does not have a transportation cask for RH TRU waste certified by the US Nuclear Regulatory Commission (NRC). These issues are discussed along with possible solutions and consequences from these solutions. 46 refs

TRU [transuranic] waste certification compliance requirements for acceptance of newly generated contact-handled wastes to be shipped to the Waste Isolation Pilot Plant: Revision 2

International Nuclear Information System (INIS)

1989-01-01

Compliance requirements are presented for certifying that unclassified, newly generated (NG), contact-handled (CH) transuranic (TRU) solid wastes from defense programs meet the Waste Isolation Pilot Plant (WIPP) Waste Acceptance Criteria (WAC). Where appropriate, transportation and interim storage requirements are incorporated; however, interim storage sites may have additional requirements consistent with these requirements. All applicable Department of Energy (DOE) orders must continue to be met. The compliance requirements for stored or buried waste are not addressed in this document. The compliance requirements are divided into four sections, primarily determined by the general feature that the requirements address. These sections are General Requirements, Waste Container Requirements, Waste Form Requirements, and Waste Package Requirements. The waste package is the combination of waste container and waste. 10 refs., 1 fig

Management of remote-handled defense transuranic wastes

International Nuclear Information System (INIS)

Ebra, M.A.; Pierce, G.D.; Carson, P.H.

1988-01-01

Transuranic (TRU) wastes generated by defense-related activities are scheduled for emplacement at the Waste Isolation Pilot Plant (WIPP) in New Mexico beginning in October 1988. After five years of operation as a research and development facility, the WIPP may be designated as a permanent repository for these wastes, if it has been demonstrated that this deep, geologically stable formation is a safe disposal option. Defense TRU wastes are currently stored at various Department of Energy (DOE) sites across the nation. Approximately 2% by volume of currently stored TRU wastes are defined, on the basis of dose rates, as remote-handled (RH). RH wastes continue to be generated at various locations operated by DOE contractors. They require special handling and processing prior to and during emplacement in the WIPP. This paper describes the strategy for managing defense RH TRU wastes

Remote-Handled Transuranic Content Codes

Energy Technology Data Exchange (ETDEWEB)

Washington TRU Solutions

2006-12-01

The Remote-Handled Transuranic (RH-TRU) Content Codes (RH-TRUCON) document describes the inventory of RH-TRU waste within the transportation parameters specified by the Remote-Handled Transuranic Waste Authorized Methods for Payload Control (RH-TRAMPAC).1 The RH-TRAMPAC defines the allowable payload for the RH-TRU 72-B. This document is a catalog of RH-TRU 72-B authorized contents by site. A content code is defined by the following components: • A two-letter site abbreviation that designates the physical location of the generated/stored waste (e.g., ID for Idaho National Laboratory [INL]). The site-specific letter designations for each of the sites are provided in Table 1. • A three-digit code that designates the physical and chemical form of the waste (e.g., content code 317 denotes TRU Metal Waste). For RH-TRU waste to be transported in the RH-TRU 72-B, the first number of this three-digit code is “3.” The second and third numbers of the three-digit code describe the physical and chemical form of the waste. Table 2 provides a brief description of each generic code. Content codes are further defined as subcodes by an alpha trailer after the three-digit code to allow segregation of wastes that differ in one or more parameter(s). For example, the alpha trailers of the subcodes ID 322A and ID 322B may be used to differentiate between waste packaging configurations. As detailed in the RH-TRAMPAC, compliance with flammable gas limits may be demonstrated through the evaluation of compliance with either a decay heat limit or flammable gas generation rate (FGGR) limit per container specified in approved content codes. As applicable, if a container meets the watt*year criteria specified by the RH-TRAMPAC, the decay heat limits based on the dose-dependent G value may be used as specified in an approved content code. If a site implements the administrative controls outlined in the RH-TRAMPAC and Appendix 2.4 of the RH-TRU Payload Appendices, the decay heat or FGGR

Oak Ridge National Laboratory Transuranic Waste Certification Program

International Nuclear Information System (INIS)

Smith, J.H.; Bates, L.D.; Box, W.D.; Aaron, W.S.; Setaro, J.A.

1988-08-01

The US Department of Energy (DOE) has requested that all DOE facilities handling defense transuranic (TRU) waste develop and implement a program whereby all TRU waste will be contained, stored, and shipped to the Waste Isolation Pilot Plant (WIPP) in accordance with the requirements set forth in the DOE certification documents WIPP-DOE-069, 114, 120, 137, 157, and 158. The program described in this report describes how Oak Ridge National Laboratory (ORNL) intends to comply with these requirements and the techniques and procedures used to ensure that ORNL TRU wastes are certifiable for shipment to WIPP. This document describes the program for certification of newly generated (NG) contact-handled transuranic (CH-TRU) waste. Previsions have been made for addenda, which will extend the coverage of this document to include certification of stored CH-TRU and NG and stored remote-handled transuranic (RH-TRU) waste, as necessary. 24 refs., 11 figs., 4 tabs

Assessment of allowable transuranic activity levels for WIPP wastes

International Nuclear Information System (INIS)

1987-12-01

This study provides a technical evaluation for the establishment of an upper limit on the transuranic content of waste packages to be received. To accomplish this, the predicted radiological performance of WIPP is compared to the radiological performance requirements applicable to WIPP. These performance requirements include radiation protection standards for both routine facility operations and credible operational accidents. These requirements are discussed in Chapter 2.0. From the margin between predicted performance and the performance requirements, the maximum allowable transuranic content of waste packages can then be inferred. Within the resulting compliance envelope, a waste acceptance criterion can be established that delineates the allowable level of transuranic radioactivity content for contact handled (CH) and remote handled (RH) waste packages. 13 refs., 8 tabs

Hanford contact-handled transuranic drum retrieval project planning document

International Nuclear Information System (INIS)

DEMITER, J.A.

1998-01-01

The Hanford Site is one of several US Department of Energy (DOE) sites throughout the US that has generated and stored transuranic (TRU) wastes. The wastes were primarily placed in 55-gallon drums, stacked in trenches, and covered with soil. In 1970, the Nuclear Regulatory Commission ordered that TRU wastes be segregated from other radioactive wastes and placed in retrievable storage until such time that the waste could be sent to a geologic repository and permanently disposed. Retrievable storage also defined container storage life by specifying that a container must be retrievable as a contamination-free container for 20 years. Hanford stored approximately 37,400 TRU containers in 20-year retrievable storage from 1970 to 1988. The Hanford TRU wastes placed in 20-year retrievable storage are considered disposed under existing Resource Conservation and Recovery Act (RCRA) regulations since they were placed in storage prior to September 1988. The majority of containers were 55-gallon drums, but 20-year retrievable storage includes several TRU wastes covered with soil in different storage methods

A passive-active neutron device for assaying remote-handled transuranic waste

International Nuclear Information System (INIS)

Estep, R.J.; Coop, K.L.; Deane, T.M.; Lujan, J.E.

1990-01-01

A combined passive-active neutron assay device was constructed for assaying remote-handled transuranic waste. A study of matrix and source position effects in active assays showed that a knowledge of the source position alone is not sufficient to correct for position-related errors in highly moderating or absorbing matrices. An alternate function for the active assay of solid fuel pellets was derived, although the efficacy of this approach remains to be established

76 FR 33277 - Proposed Approval of the Central Characterization Project's Remote-Handled Transuranic Waste...

Science.gov (United States)

2011-06-08

... disposal of TRU radioactive waste. As defined by the WIPP Land Withdrawal Act (LWA) of 1992 (Pub. L. 102... certification of the WIPP's compliance with disposal regulations for TRU radioactive waste [63 Federal Register... radioactive remote-handled (RH) transuranic (TRU) waste characterization program implemented by the Central...

Defense Remote Handled Transuranic Waste Cost/Schedule Optimization Study

International Nuclear Information System (INIS)

Pierce, G.D.; Wolaver, R.W.; Carson, P.H.

1986-11-01

The purpose of this study is to provide the DOE information with which it can establish the most efficient program for the long management and disposal, in the Waste Isolation Pilot Plant (WIPP), of remote handled (RH) transuranic (TRU) waste. To fulfill this purpose, a comprehensive review of waste characteristics, existing and projected waste inventories, processing and transportation options, and WIPP requirements was made. Cost differences between waste management alternatives were analyzed and compared to an established baseline. The result of this study is an information package that DOE can use as the basis for policy decisions. As part of this study, a comprehensive list of alternatives for each element of the baseline was developed and reviewed with the sites. The principle conclusions of the study follow. A single processing facility for RH TRU waste is both necessary and sufficient. The RH TRU processing facility should be located at Oak Ridge National Laboratory (ORNL). Shielding of RH TRU to contact handled levels is not an economic alternative in general, but is an acceptable alternative for specific waste streams. Compaction is only cost effective at the ORNL processing facility, with a possible exception at Hanford for small compaction of paint cans of newly generated glovebox waste. It is more cost effective to ship certified waste to WIPP in 55-gal drums than in canisters, assuming a suitable drum cask becomes available. Some waste forms cannot be packaged in drums, a canister/shielded cask capability is also required. To achieve the desired disposal rate, the ORNL processing facility must be operational by 1996. Implementing the conclusions of this study can save approximately $110 million, compared to the baseline, in facility, transportation, and interim storage costs through the year 2013. 10 figs., 28 tabs

Structural analysis of the TRansUranic PACkage Transporter (TRUPACT)

International Nuclear Information System (INIS)

Lamoreaux, G.H.; Sutherland, S.H.; Duffey, T.A.

1981-07-01

The TRansUranic PACkage Transporter (TRUPACT) is a Type B container under development at the Transportation Technology Center, Sandia National Laboratory, for use in the transportation of contact-handled transuranic waste. This report describes the numerical analyses of the container's response to end-on, side-on, and center of gravity over corner impacts on an unyielding surface following a 9 m free fall. The results of the analyses are compared to available experimental data. In general, the analytical predictions and experimental comparisons confirm the validity of the TRUPACT design concept

Remote Handled Transuranic Sludge Retrieval Transfer And Storage System At Hanford

International Nuclear Information System (INIS)

Raymond, Rick E.; Frederickson, James R.; Criddle, James; Hamilton, Dennis; Johnson, Mike W.

2012-01-01

This paper describes the systems developed for processing and interim storage of the sludge managed as remote-handled transuranic (RH-TRU). An experienced, integrated CH2M HILL/AFS team was formed to design and build systems to retrieve, interim store, and treat for disposal the K West Basin sludge, namely the Sludge Treatment Project (STP). A system has been designed and is being constructed for retrieval and interim storage, namely the Engineered Container Retrieval, Transfer and Storage System (ECRTS)

Remote Handled Transuranic Sludge Retrieval Transfer And Storage System At Hanford

Energy Technology Data Exchange (ETDEWEB)

Raymond, Rick E. [CH2M HILL Plateau Remediation Company, Richland, WA (United States); Frederickson, James R. [AREVA, Avignon (France); Criddle, James [AREVA, Avignon (France); Hamilton, Dennis [CH2M HILL Plateau Remediation Company, Richland, WA (United States); Johnson, Mike W. [CH2M HILL Plateau Remediation Company, Richland, WA (United States)

2012-10-18

This paper describes the systems developed for processing and interim storage of the sludge managed as remote-handled transuranic (RH-TRU). An experienced, integrated CH2M HILL/AFS team was formed to design and build systems to retrieve, interim store, and treat for disposal the K West Basin sludge, namely the Sludge Treatment Project (STP). A system has been designed and is being constructed for retrieval and interim storage, namely the Engineered Container Retrieval, Transfer and Storage System (ECRTS).

Plans for Managing Hanford Remote Handled Transuranic (TRU) Waste

International Nuclear Information System (INIS)

MCKENNEY, D.E.

2001-01-01

The current Hanford Site baseline and life-cycle waste forecast predicts that approximately 1,000 cubic meters of remote-handled transuranic (RH-TRU) waste will be generated by waste management and environmental restoration activities at Hanford. These 1,000 cubic meters, comprised of both transuranic and mixed transuranic (TRUM) waste, represent a significant portion of the total estimated inventory of RH-TRU to be disposed of at the Waste Isolation Pilot Plant (WIPP). A systems engineering approach is being followed to develop a disposition plan for each RH-TRU/TRUM waste stream at Hanford. A number of significant decision-making efforts are underway to develop and finalize these disposition plans, including: development and approval of a RH-TRU/TRUM Waste Project Management Plan, revision of the Hanford Waste Management Strategic Plan, the Hanford Site Options Study (''Vision 2012''), the Canyon Disposal Initiative Record-of-Decision, and the Hanford Site Solid (Radioactive and Hazardous) Waste Program Environmental Impact Statement (SW-EIS). Disposition plans may include variations of several options, including (1) sending most RH-TRU/TRUM wastes to WIPP, (2) deferrals of waste disposal decisions in the interest of both efficiency and integration with other planned decision dates and (3) disposition of some materials in place consistent with Department of Energy Orders and the regulations in the interest of safety, risk minimization, and cost. Although finalization of disposition paths must await completion of the aforementioned decision documents, significant activities in support of RH-TRU/TRUM waste disposition are proceeding, including Hanford participation in development of the RH TRU WIPP waste acceptance criteria, preparation of T Plant for interim storage of spent nuclear fuel sludge, sharing of technology information and development activities in cooperation with the Mixed Waste Focus Area, RH-TRU technology demonstrations and deployments, and

Westinghouse Hanford Company plan for certifying newly generated contact -- handled transuranic waste. Revision 1

International Nuclear Information System (INIS)

Lipinski, R.M.; Backlund, E.G.

1995-09-01

All transuranic (TRU) waste generators are required by US Department of Energy (DOE) Order 5820.2A to package their TRU waste in order to comply wit the Waste Isolation Pilot Plant (WIPP) -- Waste Acceptance Criteria (WAC) or keep non-certifiable containers segregated. The Westinghouse Hanford Company (WHC) Transuranic Waste Certification Plan was developed to ensure that TRU newly generated waste at WHC meets the DOE Order 5820.2A and the WHC-WAC which includes the State of Washington Department of Ecology -- Washington Administrative Code (DOE-WAC). The metho used at WHC to package TRU waste are described in sufficient detail to meet the regulations. This document is organized to provide a brief overview of waste generation operations at WHC. The methods used to implement this plan are discussed briefly along with the responsibilities and authorities of applicable organizations. This plan describes how WHC complies with all applicable regulations and requirements set forth in the latest approved revision of WHC-EP-0063-4

Remote-Handled Transuranic Waste Content Codes (RH-Trucon)

International Nuclear Information System (INIS)

2006-01-01

The Remote-Handled Transuranic (RH-TRU) Content Codes (RH-TRUCON) document describes the inventory of RH-TRU waste within the transportation parameters specified by the Remote-Handled Transuranic Waste Authorized Methods for Payload Control (RH-TRAMPAC). The RH-TRAMPAC defines the allowable payload for the RH-TRU 72-B. This document is a catalog of RH-TRU 72-B authorized contents by site. A content code is defined by the following components: (1) A two-letter site abbreviation that designates the physical location of the generated/stored waste (e.g., ID for Idaho National Laboratory [INL]). The site-specific letter designations for each of the sites are provided in Table 1. (2) A three-digit code that designates the physical and chemical form of the waste (e.g., content code 317 denotes TRU Metal Waste). For RH-TRU waste to be transported in the RH-TRU 72-B, the first number of this three-digit code is ''3''. The second and third numbers of the three-digit code describe the physical and chemical form of the waste. Table 2 provides a brief description of each generic code. Content codes are further defined as subcodes by an alpha trailer after the three-digit code to allow segregation of wastes that differ in one or more parameter(s). For example, the alpha trailers of the subcodes ID 322A and ID 322B may be used to differentiate between waste packaging configurations. As detailed in the RH-TRAMPAC, compliance with flammable gas limits may be demonstrated through the evaluation of compliance with either a decay heat limit or flammable gas generation rate (FGGR) limit per container specified in approved content codes. As applicable, if a container meets the watt*year criteria specified by the RH-TRAMPAC, the decay heat limits based on the dose-dependent G value may be used as specified in an approved content code. If a site implements the administrative controls outlined in the RH-TRAMPAC and Appendix 2.4 of the RH-TRU Payload Appendices, the decay heat or FGGR

Process Description for the Retrieval of Earth Covered Transuranic (TRU) Waste Containers at the Hanford Site

International Nuclear Information System (INIS)

DEROSA, D.C.

2000-01-01

This document describes process and operational options for retrieval of the contact-handled suspect transuranic waste drums currently stored below grade in earth-covered trenches at the Hanford Site. Retrieval processes and options discussed include excavation, container retrieval, venting, non-destructive assay, criticality avoidance, incidental waste handling, site preparation, equipment, and shipping

Process Description for the Retrieval of Earth Covered Transuranic (TRU) Waste Containers at the Hanford Site

Energy Technology Data Exchange (ETDEWEB)

DEROSA, D.C.

2000-01-13

This document describes process and operational options for retrieval of the contact-handled suspect transuranic waste drums currently stored below grade in earth-covered trenches at the Hanford Site. Retrieval processes and options discussed include excavation, container retrieval, venting, non-destructive assay, criticality avoidance, incidental waste handling, site preparation, equipment, and shipping.

Report of the remote-handled transuranic waste mock retrieval demonstration

International Nuclear Information System (INIS)

1987-05-01

This report documents the results of the mock, onsite retrieval demonstration that was conducted on May 19 and 20, 1987, for representatives of the New Mexico Environmental Evaluation Group (EEG). Demonstration of the retrievability of remote-handled transuranic (RH TRU) waste is part of a milestone included in the Agreement for Consultation and Cooperation between the state of New Mexico and the United States Department of Energy. Retrieval equipment design documents and a retrievability demonstration plan for RH TRU waste were previously transmitted to the EEG. This report documents the results of the demonstration by evaluating the demonstration against the acceptance criteria that were established in the Demonstration Plan. 1 fig., 2 tabs

Status of microwave process development for RH-TRU [remote-handled transuranic] wastes at Oak Ridge National Laboratory

International Nuclear Information System (INIS)

White, T.L.; Youngblood, E.L.; Berry, J.B.; Mattus, A.J.

1990-01-01

The Oak Ridge National Laboratory (ORNL) Waste Handling and Packaging Plant is developing a microwave process to reduce and solidify remote-handled transuranic (RH-TRU) liquids and sludges presently stored in large tanks at ORNL. Testing has recently begun on an in-drum microwave process using nonradioactive RH-TRU surrogates. The microwave process development effort has focused on an in-drum process to dry the RH-TRU liquids and sludges in the final storage container and then melt the salt residues to form a solid monolith. A 1/3-scale proprietary microwave applicator was designed, fabricated, and tested to demonstrate the essential features of the microwave design and to provide input into the design of the full-scale applicator. The microwave fields are uniform in one dimension to reduce the formation of hot spots on the microwaved wasteform. The final wasteform meets the waste acceptance criteria for the Waste Isolation Pilot Plant, a federal repository for defense transuranic wastes near Carlsbad, New Mexico. 7 refs., 1 fig., 1 tab

Transport, handling, and interim storage of intermediate-level transuranic waste at the INEL

International Nuclear Information System (INIS)

Metzger, J.C.; Snyder, A.M.

1977-09-01

The Idaho National Engineering Laboratory stores transuranic (TRU)-contaminated waste emitting significant amounts of beta-gamma radiation. This material is referred to as intermediate-level TRU waste. The Energy Research and Development Administration requires that this waste be stored retrievably during the interim before a Federal repository becomes operational. Waste form and packaging criteria for the eventual storage of this waste at a Federal repository, i.e., the Waste Isolation Pilot Plant (WIPP), have been tentatively established. The packaging and storage techniques now in use at the Idaho National Engineering Laboratory are compatible with these criteria and also meet the requirement that the waste containers remain in a readily-retrievable, contamination-free condition during the interim storage period. The Intermediate Level Transuranic Storage Facility (ILTSF) provides below-grade storage in steel pipe vaults for intermediate-level TRU waste prior to shipment to the WIPP. Designated waste generating facilities, operated for the Energy Research and Development Administration, use a variety of packaging and transportation methods to deliver this waste to the ILTSF. Transfer of the waste containers to the ILTSF storage vaults is accomplished using handling methods compatible with these waste packaging and transport methods

Transuranic waste: long-term planning

International Nuclear Information System (INIS)

Young, K.C.

1985-07-01

Societal concerns for the safe handling and disposal of toxic waste are behind many of the regulations and the control measures in effect today. Transuranic waste, a specific category of toxic (radioactive) waste, serves as a good example of how regulations and controls impact changes in waste processing - and vice versa. As problems would arise with waste processing, changes would be instituted. These changes improved techniques for handling and disposal of transuranic waste, reduced the risk of breached containment, and were usually linked with regulatory changes. Today, however, we face a greater public awareness of and concern for toxic waste control; thus, we must anticipate potential problems and work on resolving them before they can become real problems. System safety analyses are valuable aids in long-term planning for operations involving transuranic as well as other toxic materials. Examples of specific system safety analytical methods demonstrate how problems can be anticipated and resolution initiated in a timely manner having minimal impacts upon allocation of resource and operational goals. 7 refs., 1 fig

Waste Isolation Pilot Plant contact-handled transuranic waste preoperational checkout: Final report

International Nuclear Information System (INIS)

1988-07-01

This report documents the results of the WIPP CH TRU Preoperational Checkout which was completed between June 8 and June 14, 1988 during which period, a total of 10 TRUPACT shipping containers were processed from site receipt through emplacement of the simulated waste packages in the underground storage area. Since the design of WIPP includes provisions to unload an internally contaminated TRUPACT, in the controlled environment of the Overpack and Repair Room, one TRUPACT was partially processed through this sequence of operations to verify this portion of the waste handling process as part of the checkout. The successful completion of the CH TRU Preoperational Checkout confirmed the acceptability of WIPP operating procedures, personnel, equipment, and techniques. Extrapolation of time-line data using a computer simulation model of the waste handling process has confirmed that WIPP operations can achieve the design throughput capability of 500,000 ft 3 /year, if required, using two waste handling shifts. The single shift throughput capability of 273,000 ft 3 /year exceeds the anticipated operating receival rate of about 230,000 ft 3 /year. At the 230,000 ft 3 /year rate, the combined CH TRU annual operator dose and the average individual dose (based on minimum crew size) is projected to be 13.7 rem and 0.7 rem, respectively. 6 refs., 27 figs., 3 tabs

Full scale tests on remote handled FFTF fuel assembly waste handling and packaging

International Nuclear Information System (INIS)

Allen, C.R.; Cash, R.J.; Dawson, S.A.; Strode, J.N.

1986-01-01

Handling and packaging of remote handled, high activity solid waste fuel assembly hardware components from spent FFTF reactor fuel assemblies have been evaluated using full scale components. The demonstration was performed using FFTF fuel assembly components and simulated components which were handled remotely using electromechanical manipulators, shielding walls, master slave manipulators, specially designed grapples, and remote TV viewing. The testing and evaluation included handling, packaging for current and conceptual shipping containers, and the effects of volume reduction on packing efficiency and shielding requirements. Effects of waste segregation into transuranic (TRU) and non-transuranic fractions also are discussed

Process to separate transuranic elements from nuclear waste

Science.gov (United States)

Johnson, T.R.; Ackerman, J.P.; Tomczuk, Z.; Fischer, D.F.

1989-03-21

A process is described for removing transuranic elements from a waste chloride electrolytic salt containing transuranic elements in addition to rare earth and other fission product elements so the salt waste may be disposed of more easily and the valuable transuranic elements may be recovered for reuse. The salt is contacted with a cadmium-uranium alloy which selectively extracts the transuranic elements from the salt. The waste salt is generated during the reprocessing of nuclear fuel associated with the Integral Fast Reactor (IFR). 2 figs.

Process to separate transuranic elements from nuclear waste

International Nuclear Information System (INIS)

Johnson, T.R.; Ackerman, J.P.; Tomczuk, Z.; Fischer, D.F.

1989-01-01

A process is described for removing transuranic elements from a waste chloride electrolytic salt containing transuranic elements in addition to rare earth and other fission product elements so the salt waste may be disposed of more easily and the valuable transuranic elements may be recovered for reuse. The salt is contacted with a cadmium-uranium alloy which selectively extracts the transuranic elements from the salt. The waste salt is generated during the reprocessing of nuclear fuel associated with the Integral Fast Reactor (IFR). 2 figs

Remote-Handled Transuranic Content Codes

International Nuclear Information System (INIS)

2001-01-01

The Remote-Handled Transuranic (RH-TRU) Content Codes (RH-TRUCON) document represents the development of a uniform content code system for RH-TRU waste to be transported in the 72-Bcask. It will be used to convert existing waste form numbers, content codes, and site-specific identification codes into a system that is uniform across the U.S. Department of Energy (DOE) sites.The existing waste codes at the sites can be grouped under uniform content codes without any lossof waste characterization information. The RH-TRUCON document provides an all-encompassing description for each content code and compiles this information for all DOE sites. Compliance with waste generation, processing, and certification procedures at the sites (outlined in this document foreach content code) ensures that prohibited waste forms are not present in the waste. The content code gives an overall description of the RH-TRU waste material in terms of processes and packaging, as well as the generation location. This helps to provide cradle-to-grave traceability of the waste material so that the various actions required to assess its qualification as payload for the 72-B cask can be performed. The content codes also impose restrictions and requirements on the manner in which a payload can be assembled. The RH-TRU Waste Authorized Methods for Payload Control (RH-TRAMPAC), Appendix 1.3.7 of the 72-B Cask Safety Analysis Report (SAR), describes the current governing procedures applicable for the qualification of waste as payload for the 72-B cask. The logic for this classification is presented in the 72-B Cask SAR. Together, these documents (RH-TRUCON, RH-TRAMPAC, and relevant sections of the 72-B Cask SAR) present the foundation and justification for classifying RH-TRU waste into content codes. Only content codes described in thisdocument can be considered for transport in the 72-B cask. Revisions to this document will be madeas additional waste qualifies for transport. Each content code uniquely

TRANSURANIC METAL HALIDES AND A PROCESS FOR THE PRODUCTION THEREOF

Science.gov (United States)

Fried, S.

1951-03-20

Halides of transuranic elements are prepared by contacting with aluminum and a halogen, or with an aluminum halide, a transuranic metal oxide, oxyhalide, halide, or mixture thereof at an elevated temperature.

Final Hanford Site Transuranic (TRU) Waste Characterization QA Project Plan

International Nuclear Information System (INIS)

GREAGER, T.M.

2000-01-01

The Quality Assurance Project Plan (QAPjP) has been prepared for waste characterization activities to be conducted by the Transuranic (TRU) Project at the Hanford Site to meet requirements set forth in the Waste Isolation Pilot Plan (WIPP) Hazardous Waste Facility Permit, 4890139088-TSDF, Attachment B, including Attachments B1 through B6 (WAP) (DOE, 1999a). The QAPjP describes the waste characterization requirements and includes test methods, details of planned waste sampling and analysis, and a description of the waste characterization and verification process. In addition, the QAPjP includes a description of the quality assurance/quality control (QA/QC) requirements for the waste characterization program. Before TRU waste is shipped to the WIPP site by the TRU Project, all applicable requirements of the QAPjP shall be implemented. Additional requirements necessary for transportation to waste disposal at WIPP can be found in the ''Quality Assurance Program Document'' (DOE 1999b) and HNF-2600, ''Hanford Site Transuranic Waste Certification Plan.'' TRU mixed waste contains both TRU radioactive and hazardous components, as defined in the WLPP-WAP. The waste is designated and separately packaged as either contact-handled (CH) or remote-handled (RH), based on the radiological dose rate at the surface of the waste container. RH TRU wastes are not currently shipped to the WIPP facility

User's manual for remote-handled transuranic waste container welding and inspection fixture

International Nuclear Information System (INIS)

Hauptmann, J.P.

1985-09-01

Rockwell Hanford Operations (Rockwell) has designed built, and tested a prototype remotely operated welding and inspection fixture to be used in making the closure weld on the remote-handled transuranic (RH-TRU) waste container. The RH-TRU waste container has an average TRU concentration in excess of 100 nCi/gm, and a surface radiation dose rate in excess of 200 mrem/h, but not exceeding 100 rem/h. The RH-TRU waste container is to be used by defense waste generator sites in the United States for final packaging of RH-TRU wastes and is compatible with the requirements of the Waste Isolation Pilot Plant (WIPP) and the WIPP handling system. Standard and stacked RH-TRU container designs are available. The standard container is 26 in. in dia. by 121 in. high; the stacked containers are 26 in. in dia. by 61.25 in. high. After loading, two stacked containers are fitted and welded together to form the identical measurements of the standard 121-in. container. The prototype RH-TRU waste container welding and inspection fixture was intended for test and evaluation only, and not for installation in an operating facility. The final RH-TRU waste container welding and inspection fixture drawings (see appendix) incorporate several changes made following operational testing of the original fixture. These modifications are identified in this manual. However, not all modifications have been functionally tested. The purpose of this manual is to aid waste generator sites in designing a remotely operated welding and inspection fixture that will conform to their own requirements. Modifications to the Rockwell design must be evaluated for structural and WIPP handling requirements. This manual also provides design philosophy, component vendor information, and cost estimates

Hanford Site Transuranic (TRU) Waste Certification Plan

Energy Technology Data Exchange (ETDEWEB)

GREAGER, T.M.

1999-09-09

The Hanford Site Transuranic Waste Certification Plan establishes the programmatic framework and criteria within which the Hanford Site ensures that contract-handled TRU wastes can be certified as compliant with the WIPP WAC and TRUPACT-II SARP.

Hanford Site Transuranic (TRU) Waste Certification Plan

International Nuclear Information System (INIS)

GREAGER, T.M.

1999-01-01

The Hanford Site Transuranic Waste Certification Plan establishes the programmatic framework and criteria with in which the Hanford Site ensures that contract-handled TRU wastes can be certified as compliant with the WIPP WAC and TRUPACT-II SARP

IMPROVEMENTS IN HANFORD TRANSURANIC (TRU) PROGRAM UTILIZING SYSTEMS MODELING AND ANALYSES

International Nuclear Information System (INIS)

UYTIOCO EM

2007-01-01

Hanford's Transuranic (TRU) Program is responsible for certifying contact-handled (CH) TRU waste and shipping the certified waste to the Waste Isolation Pilot Plant (WIPP). Hanford's CH TRU waste includes material that is in retrievable storage as well as above ground storage, and newly generated waste. Certifying a typical container entails retrieving and then characterizing it (Real-Time Radiography, Non-Destructive Assay, and Head Space Gas Sampling), validating records (data review and reconciliation), and designating the container for a payload. The certified payload is then shipped to WIPP. Systems modeling and analysis techniques were applied to Hanford's TRU Program to help streamline the certification process and increase shipping rates

Criticality safety of transuranic storage arrays at the Waste Isolation Pilot Plant

International Nuclear Information System (INIS)

Boyd, W.A.; Fecteau, M.W.

1993-01-01

The Waste Isolation Pilot Plant (WIPP) facility is designed to store transuranic waste that will consist mainly of surface contaminate articles and sludge. The fissile material in the waste is predominantly 239 Pu. The waste is grouped into two categories: contact-handled waste, which will be stored in 55-gal steel drums or in steel boxes, and remote-handled waste, which will be stored in specially designed cylindrical steel canisters. To show that criticality safety will be acceptable, criticality analyses were performed to demonstrate that a large number of containers with limiting loadings of fissile material could be stored at the site and meet a k eff limit of 0.95. Criticality analyses based on the classic worst-case moderated plutonium sphere approach would severely limit the capacity for storage of waste at the facility. Therefore, these analyses use realistic or credible worst-case assumptions to better represent the actual storage situation without compromising the margin of safety. Numerous sensitivity studies were performed to determine the importance of various parameters on the criticality of the configuration. It was determined that the plutonium loading has the dominant effect on the system reactivity. Nearly all other reactivity variations from the sensitivity studies were found to be relatively small. The analysis shows that criticality of the contact-handled waste storage drums and boxes and the remote-handled canisters is prevented by restrictions on maximum fissile loading per container and on the size of handling/storage areas

Transuranic contaminated waste functional definition and implementation

International Nuclear Information System (INIS)

Kniazewycz, B.G.

1980-03-01

The purpose of this report is to examine the problem(s) of TRU waste classification and to document the development of an easy-to-apply standard(s) to determine whether or not this waste package should be emplaced in a geologic repository for final disposition. Transuranic wastes are especially significant because they have long half-lives and some are rather radiotoxic. Transuranic radionuclides are primarily produced by single or multiple neutron capture by U-238 in fuel elements during the operation of a nuclear reactor. Reprocessing of spent fuel elements attempts to remove plutonium, but since the separation is not complete, the resulting high-activity liquids still contain some plutonium as well as other transuranics. Likewise, transuranic contamination of low-activity wastes also occurs when the transuranic materials are handled or processed, which is primarily at federal facilities involved in R and D and nuclear weapons production. Transuranics are persistent in the environment and, as a general rule, are strongly retained by soils. They are not easily transported through most food chains, although some reconcentration does take place in the aquatic food chain. They pose no special biological hazard to humans upon ingestion because they are weakly absorbed from the gastrointestional tract. A greater hazard results from inhalation since they behave like normal dust and fractionate accordingly

Transportation packagings for high-level wastes and unprocessed transuranic wastes

International Nuclear Information System (INIS)

Wilmot, E.L.; Romesberg, L.E.

1982-01-01

Packagings used for nuclear waste transport are varied in size, shape, and weight because they must accommodate a wide variety of waste forms and types. However, this paper will discuss the common characteristics among the packagings in order to provide a broad understanding of packaging designs. The paper then discusses, in some detail, a design that has been under development recently at Sandia National Laboratories (SNL) for handling unprocessed, contact-handled transuranic (CHTRU) wastes as well as a cask design for defense high-level wastes (HLW). As presently conceived, the design of the transuranic package transporter (TRUPACT) calls for inner and outer boxes that are separated by a rigid polyurethane foam. The inner box has a steel frame with stainless steel surfaces; the outer box is similarly constructed except that carbon steel is used for the outside surfaces. The access to each box is through hinged doors that are sealed after loading. To meet another waste management need, a cask is being developed to transport defense HLW. The cask, which is at the preliminary design stage, is being developed by General Atomic under the direction of the TTC. The cask design relies heavily on state-of-the-art spent-fuel cask designs though it can be much simpler due to the characteristics of the HLW. A primary purpose of this paper is to show that CHTRU waste and defense HLW currently are and will be transported in packagings designed to meet the hazards of transportation that are present in general commerce

Waste Generator Instructions: Key to Successful Implementation of the US DOE's 435.1 for Transuranic Waste Packaging Instructions (LA-UR-12-24155) - 13218

International Nuclear Information System (INIS)

French, David M.; Hayes, Timothy A.; Pope, Howard L.; Enriquez, Alejandro E.; Carson, Peter H.

2013-01-01

In times of continuing fiscal constraints, a management and operation tool that is straightforward to implement, works as advertised, and virtually ensures compliant waste packaging should be carefully considered and employed wherever practicable. In the near future, the Department of Energy (DOE) will issue the first major update to DOE Order 435.1, Radioactive Waste Management. This update will contain a requirement for sites that do not have a Waste Isolation Pilot Plant (WIPP) waste certification program to use two newly developed technical standards: Contact-Handled Defense Transuranic Waste Packaging Instructions and Remote-Handled Defense Transuranic Waste Packaging Instructions. The technical standards are being developed from the DOE O 435.1 Notice, Contact-Handled and Remote-Handled Transuranic Waste Packaging, approved August 2011. The packaging instructions will provide detailed information and instruction for packaging almost every conceivable type of transuranic (TRU) waste for disposal at WIPP. While providing specificity, the packaging instructions leave to each site's own discretion the actual mechanics of how those Instructions will be functionally implemented at the floor level. While the Technical Standards are designed to provide precise information for compliant packaging, the density of the information in the packaging instructions necessitates a type of Rosetta Stone that translates the requirements into concise, clear, easy to use and operationally practical recipes that are waste stream and facility specific for use by both first line management and hands-on operations personnel. The Waste Generator Instructions provide the operator with step-by-step instructions that will integrate the sites' various operational requirements (e.g., health and safety limits, radiological limits or dose limits) and result in a WIPP certifiable waste and package that can be transported to and emplaced at WIPP. These little known but widely productive Waste

Transuranic package transporter (TRUPACT) system design status and operational support equipment

International Nuclear Information System (INIS)

Johanson, N.W.; Meyer, R.J.; Romesberg, L.E.; Pope, R.B.

1983-01-01

A program was initiated in the late 1970's at Sandia National Laboratories to develop an efficient, safe, reliable, and cost-effective transportation packaging system for the carriage of contact-handled transuranic (CH-TRU) waste within the Department of Energy (DOE) complex. It is anticipated that eventually a family of TRUPACT (TRansUranic PACKage Transporter) systems having varied dimensions and weight/volume capacities will be needed by the DOE to transport different CH-TRU waste forms. Each TRUPACT system will be a Type B packaging. Large quantities of CH-TRU wastes having many different forms, isotopic contents, and contained in a variety of waste containers have been, are being, and will continue to be produced and stored for ultimate disposal. Packaging design is being closely coordinated with facility designs to ensure the rapid and economic integration of the TRUPACT system. The first packaging developed for transport by truck or rail (bimodal) is designated TRUPACT-I and will become operational in 1984. This paper provides an overview of progress on the TRUPACT-I design and details of equipment to be used for interfacing with users

Economic evaluation of volume reduction for Defense transuranic waste

International Nuclear Information System (INIS)

Brown, C.M.

1982-03-01

The economics of volume reduction of retrievably stored and newly generated DOE transuranic wastes are evaluated by comparing the costs of reduction of the wastes with the savings possible in transportation and disposal. A general approach to the comparison of TRU waste volume reduction costs and cost savings is developed, an initial set of cost data is established, conclusions to support selecting technologies and facilities for the disposal of DOE transuranic waste are developed. Section I outlines the analysis which considers seven types of volume reduction from incineration and compaction of combustibles to compaction, size reduction, shredding, melting, and decontamination of metals. The study considers the volume reduction of contact-handled, newly generated and retrievably stored DOE transuranic wastes. Section II of this report describes the analytical approach, assumptions, and flow of waste material through sites. Section III presents the waste inventories, disposal and transportation savings, and volume reduction techniques and costs. Section IV contains the results and conclusions of the study. The major conclusions drawn from the study are: For DOE sites with a small amount of waste requiring disposal ( 3 /year) the cost of volume reduction is greater than the transportation and disposal savings from volume reduction provided the waste requires little additional preparation to meet transportation and disposal criteria. Wastes that do not meet these criteria require site specific economic analysis outside the general evaluations of this study. For Idaho National Engineering Laboratory, incineration and metal shredding are cost-effective, provided a facility is to be constructed as a consequence of repackaging the fraction of stored waste which may require repackaging and immobilizing chemical process waste to meet disposal criteria

Long-term management USDOE transuranic waste

International Nuclear Information System (INIS)

Bennett, W.S.; Gilbert, K.V.; Lowrey, R.Y.

1982-01-01

Activities for permanent disposal of US DOE TRU waste are presently focused on newly generated and stored waste. The buried waste and contaminated soils pose no near term problem. Decisions on any possible actions for these wastes will be deferred until the newly generated and stored wastes are being placed into disposal on a routine basis. Several elements must be in place before such disposal can become routine. These elements consist of: a disposal facility; waste acceptance criteria; waste certification mechanisms; waste processing facilities; and a waste transportation system. Each of these elements has been the subject of considerable activity in the recent past. Progress and plans for each element are summarized. As of January 1981, DOE has 60,500 m 3 of waste classified as Transuranic waste (TRU) in retrievable storage, and projects that additional TRU waste will be generated at an average rate of 4500 m 3 per year for the next 10 years. Over 99% of this waste is contact handled, with the remainder being remote handled, i.e., surface radiation dose levels exceeding 200 mrem/h. An estimated 273,000 m 3 of TRU waste were placed in shallow land burial prior to establishment of the 1970 policy. In addition, large quantities of soil at DOE sites are contaminated with TRU elements due to disposal of liquid wastes and by contact of soil with solid, buried waste whose original containers are now badly degraded. Possibly as much as 10,000,000 m 3 of soil are contaminated above 10 nCi/gm. Less than 1,000,000 m 3 are estimated to be contaminated above 100 nCi/gm

Waste Generator Instructions: Key to Successful Implementation of the US DOE's 435.1 for Transuranic Waste Packaging Instructions (LA-UR-12-24155) - 13218

Energy Technology Data Exchange (ETDEWEB)

French, David M. [LANL EES-12, Carlsbad, NM, Los Alamos National Laboratory, P.O. Box 1663, Los Alamos, NM 87545 (United States); Hayes, Timothy A. [LANL EES-12, Carlsbad, NM, Los Alamos National Laboratory, P.O. Box 1663, Los Alamos, NM 87545 (United States); Pope, Howard L. [Aspen Resources Ltd., Inc., P.O. Box 3038, Boulder, CO 80307 (United States); Enriquez, Alejandro E. [LANL NCO-4, Los Alamos National Laboratory, P.O. Box 1663, Los Alamos, NM 87545 (United States); Carson, Peter H. [LANL NPI-7, Los Alamos National Laboratory, P.O. Box 1663, Los Alamos, NM 87545 (United States)

2013-07-01

In times of continuing fiscal constraints, a management and operation tool that is straightforward to implement, works as advertised, and virtually ensures compliant waste packaging should be carefully considered and employed wherever practicable. In the near future, the Department of Energy (DOE) will issue the first major update to DOE Order 435.1, Radioactive Waste Management. This update will contain a requirement for sites that do not have a Waste Isolation Pilot Plant (WIPP) waste certification program to use two newly developed technical standards: Contact-Handled Defense Transuranic Waste Packaging Instructions and Remote-Handled Defense Transuranic Waste Packaging Instructions. The technical standards are being developed from the DOE O 435.1 Notice, Contact-Handled and Remote-Handled Transuranic Waste Packaging, approved August 2011. The packaging instructions will provide detailed information and instruction for packaging almost every conceivable type of transuranic (TRU) waste for disposal at WIPP. While providing specificity, the packaging instructions leave to each site's own discretion the actual mechanics of how those Instructions will be functionally implemented at the floor level. While the Technical Standards are designed to provide precise information for compliant packaging, the density of the information in the packaging instructions necessitates a type of Rosetta Stone that translates the requirements into concise, clear, easy to use and operationally practical recipes that are waste stream and facility specific for use by both first line management and hands-on operations personnel. The Waste Generator Instructions provide the operator with step-by-step instructions that will integrate the sites' various operational requirements (e.g., health and safety limits, radiological limits or dose limits) and result in a WIPP certifiable waste and package that can be transported to and emplaced at WIPP. These little known but widely

Adsorption of transuranic elements from large volume sea water

International Nuclear Information System (INIS)

Holm, E.; Ballestra, S.

1976-01-01

Some years ago a sampler for concentrating radionuclides from large volumes of sea water was developed by Silker et al. of the Battelle Northwest Laboratories. They used pure A1 2 O 3 as the adsorbent. The device has been applied successfully to the determination of 238 Pu and 239 Pu in several sea water samples. Our experience on the application of an identical system for the determination of transuranics in Mediterranean sea water was not quite as satisfactory as we had hoped. The chemistry involved in leaching up to 1 kg Al 2 O 3 . with acid, followed by removal of dissolved aluminium from the transuranic fraction, is rather tedious and time-consuming for routine use. The adsorption efficiency of transuranics, checked by dual-bed adsorption did not give consistent results. However, since the principle of the device is attractive enough for handling large volume water samples, it was felt that it was worthwhile to test other types of adsorbents which are easier to handle than Al 2 O 3 . For this purpose, chitosan and manganese dioxide were chosen and series of experiments were conducted in order to examine the suitability of these materials as an adsorbent in the system

Thermal response modeling of a contact-handled transuranic waste shipping container system to a fire

International Nuclear Information System (INIS)

Suchsland, K.E.; Kwong, K.C.; Fretter, E.F.; Boyd, R.D.; Auerbach, I.; Yoshimura, H.R.

1980-01-01

A one-dimensional thermal model has been developed to predict the response of a transuranic (TRU) waste shipping container accidentally exposed to a fire environment. The basic wall structure of the container consists of polyurethane foam (64 kg/m 3 ) sandwiched between two steel plates. The foam thermal model, based on high temperature experimental data, is developed for the case in which the virgin foam is in a nonoxidizing environment. The experimental results indicate that foam decomposition is highly heat rate dependent. At low quasi-steady heating rates, the foam changes to a bubbling black viscous liquid. At very high heating rates, pyrolysis gases are formed as the foam decomposes and a 20% (by weight) residual char remains. This porous char acts as a radiation shield which can significantly reduce thermal transport. In the case of a TRU shipping container wall, this char will slow the thermal penetration rate and drastically reduce the heat load to the container contents. When the front surface of the wall was subjected to 1333 0 K, numerical computations predict that after approximately 1800 s the foam temperature rise at a depth of 10.2 cm was less than 200 K (uncharred). After approximately 3600 s the foam temperature rise at a depth of 20.4 cm was 23 0 K. Typical waste contents temperature rise was predicted to be less than 56 0 K after 3600 s of heating

Assessment of gas flammability in transuranic waste container

International Nuclear Information System (INIS)

Connolly, M.J.; Loehr, C.A.; Djordjevic, S.M.; Spangler, L.R.

1995-01-01

The Safety Analysis Report for the TRUPACT-II Shipping Package [Transuranic Package Transporter-II (TRUPACT-II) SARP] set limits for gas generation rates, wattage limits, and flammable volatile organic compound (VOC) concentrations in transuranic (TRU) waste containers that would be shipped to the Waste Isolation Pilot Plant (WIPP). Based on existing headspace gas data for drums stored at the Idaho National Engineering Laboratory (INEL) and the Rocky Flats Environmental Technology Site (RFETS), over 30 percent of the contact-handled TRU waste drums contain flammable VOC concentrations greater than the limit. Additional requirements may be imposed for emplacement of waste in the WIPP facility. The conditional no-migration determination (NMD) for the test phase of the facility required that flame tests be performed if significant levels of flammable VOCs were present in TRU waste containers. This paper describes an approach for investigating the potential flammability of TRU waste drums, which would increase the allowable concentrations of flammable VOCS. A flammability assessment methodology is presented that will allow more drums to be shipped to WIPP without treatment or repackaging and reduce the need for flame testing on drums. The approach includes experimental work to determine mixture lower explosive limits (MLEL) for the types of gas mixtures observed in TRU waste, a model for predicting the MLEL for mixtures of VOCS, hydrogen, and methane, and revised screening limits for total flammable VOCs concentrations and concentrations of hydrogen and methane using existing drum headspace gas data and the model predictions

Centralized processing of contact-handled TRU waste feasibility analysis

International Nuclear Information System (INIS)

1986-12-01

This report presents work for the feasibility study of central processing of contact-handled TRU waste. Discussion of scenarios, transportation options, summary of cost estimates, and institutional issues are a few of the subjects discussed

Waste Isolation Pilot Plant remote-handled transuranic waste disposal strategy

International Nuclear Information System (INIS)

1995-01-01

The remote-handled transuranic (RH-TRU) waste disposal strategy described in this report identifies the process for ensuring that cost-effective initial disposal of RH-TRU waste will begin in Fiscal Year 2002. The strategy also provides a long-term approach for ensuring the efficient and sustained disposal of RH-TRU waste during the operating life of WIPP. Because Oak Ridge National Laboratory stores about 85 percent of the current inventory, the strategy is to assess the effectiveness of modifying their facilities to package waste, rather than constructing new facilities. In addition, the strategy involves identification of ways to prepare waste at other sites to supplement waste from Oak Ridge National Laboratory. DOE will also evaluate alternative packagings, modes of transportation, and waste emplacement configurations, and will select preferred alternatives to ensure initial disposal as scheduled. The long-term strategy provides a systemwide planning approach that will allow sustained disposal of RH-TRU waste during the operating life of WIPP. The DOE's approach is to consider the three relevant systems -- the waste management system at the generator/storage sites, the transportation system, and the WIPP disposal system -- and to evaluate the system components individually and in aggregate against criteria for improving system performance. To ensure full implementation, in Fiscal Years 1996 and 1997 DOE will: (1) decide whether existing facilities at Oak Ridge National Laboratory or new facilities to package and certify waste are necessary; (2) select the optimal packaging and mode of transportation for initial disposal; and (3) select an optimal disposal configuration to ensure that the allowable limits of RH-TRU waste can be disposed. These decisions will be used to identify funding requirements for the three relevant systems and schedules for implementation to ensure that the goal of initial disposal is met

Transuranic waste examination quality assurance at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Bower, J.M.

1987-01-01

Since 1954, defense-generated transuranic (TRU) waste has been received at the Radioactive Waste Management Complex (RWMC) at the Idaho National Engineering Laboratory (INEL). A major objective of the Department of Energy (DOE) Nuclear Waste Management Programs is the proper management of the defense-generated TRU waste. The Stored Waste Examination Pilot Plant (SWEPP) is providing nondestructive examination and assay of retrievably stored contact handled TRU waste in order to certify it to the Waste Isolation Pilot Plant Waste Acceptance Crtieria (WIPP-WAC). SWEPP's capabilities for certifying contact handled waste containers include weighing, real-time radiographic examination, fissile material assay examination, container integrity examination, radiological surveys and labeling of waste containers. These processes involve not only instrument accuracy but also a wide range of technician interpretation from moderate on the assay to 100% on the radiograph. This, therefore, requires a variety of quality assurance techniques to ensure that the examinations and certifications are being performed correctly. The purpose of this paper is to discuss the methods utilized by SWEPP for checking on the examination process and to ensure that waste certifications are being properly performed. Included is the application of the quality assurance techniques to each examination system, the management of the data generated by the examination, and the verifications to ensure accurate certification. 1 ref

Status of determining transuranic nuclides speciation in aqueous solution with laser spectrometry

International Nuclear Information System (INIS)

Wang Bo; Liu Dejun; Yao Jun; Chen Xi; Long Haoqi; Zeng Jishu; Su Xiguang; Fan Xianhua

2007-01-01

The knowledge about speciation of transuranic nuclides in aqueous solution is a basis for understanding the chemical and migration behavior of transuranic nuclides in aqueous solution. The speciation of transuranic nuclides with trace concentration is complicated in near neutral aqueous solutions, including change of oxidation state, complexation and colloid generation, etc. The concentrations of transuranium in near neutral aqueous solution usually below the sensitivity range of method such as conventional absorption spectroscopy. The radioactive analysis method has a very low detection limits for radionuclides, however, it wouldn' t allow the direct measurement of the transuranic species. In contrast with these methods, laser spectroscopy is an ideal method with high sensitivity, and non-contact and non-destructive for determining the speciation of transuranic nuclides. This paper summarizes the status and application of LIPAS (Laser-induced Photoacoustic Spectrometry), LIBD (Laser-induced Breakdown Detection) and TRLFS (Time-resolved Laser Fluorescence Spectrometry) to determine the speciation of transuranic nuclides with trace concentration in aqueous solutions. (authors)

Gamma-ray spectrometry combined with acceptable knowledge (GSAK). A technique for characterization of certain remote-handled transuranic (RH-TRU) wastes. Part 1. Methodology and techniques

International Nuclear Information System (INIS)

Hartwell, J.K.; McIlwain, M.E.

2005-01-01

Gamma-ray spectrometry combined with acceptable knowledge (GSAK) is a technique for the characterization of certain remote-handled transuranic (RH-TRU) wastes. GSAK uses gamma-ray spectrometry to quantify a portion of the fission product inventory of RH-TRU wastes. These fission product results are then coupled with calculated inventories derived from acceptable process knowledge to characterize the radionuclide content of the assayed wastes. GSAK has been evaluated and tested through several test exercises. GSAK approach is described, while test results are presented in Part II. (author)

Los Alamos transuranic waste size reduction facility

International Nuclear Information System (INIS)

Briesmeister, A.; Harper, J.; Reich, B.; Warren, J.L.

1982-01-01

To facilitate disposal of transuranic (TRU) waste, Los Alamos National Laboratory designed and constructed the Size Reduction Facility (SRF) during the period 1977 to 1981. This report summarizes the engineering development, installation, and early test operations of the SRF. The facility incorporates a large stainless steel enclosure fitted with remote handling and cutting equipment to obtain an estimated 4:1 volume reduction of gloveboxes and other bulky metallic wastes

Los Alamos transuranic waste size reduction facility

International Nuclear Information System (INIS)

Briesmeister, A.; Harper, J.; Reich, B.; Warren, J.L.

1982-01-01

A transuranic (TRU) Waste Size Reduction Facility (SRF) was designed and constructed at the Los Alamos National Laboratory during the period of 1977 to 1981. This paper summarizes the engineering development, installation, and early test operations of the SRF. The facility incorporates a large stainless steel enclosure fitted with remote handling and cutting equipment to obtain an estimated 4:1 volume reduction of gloveboxes and other bulky metallic wastes

Los Alamos National Laboratory transuranic waste quality assurance project plan. Revision 1

International Nuclear Information System (INIS)

1997-01-01

This Transuranic (TRU) Waste Quality Assurance Project Plan (QAPjP) serves as the quality management plan for the characterization of transuranic waste in preparation for certification and transportation. The Transuranic Waste Characterization/Certification Program (TWCP) consists of personnel who sample and analyze waste, validate and report data; and provide project management, quality assurance, audit and assessment, and records management support, all in accordance with established requirements for disposal of TRU waste at the Waste Isolation Pilot Plant (WIPP) facility. This QAPjP addresses how the TWCP meets the quality requirements of the Carlsbad Area Office (CAO) Quality Assurance Program Description (QAPD) and the technical requirements of the Transuranic Waste Characterization Quality Assurance Program Plan (QAPP). The TWCP characterizes and certifies retrievably stored and newly generated TRU waste using the waste selection, testing, sampling, and analytical techniques and data quality objectives (DQOs) described in the QAPP, the Los Alamos National Laboratory Transuranic Waste Certification Plan (Certification Plan), and the CST Waste Management Facilities Waste Acceptance Criteria and Certification [Los Alamos National Laboratory (LANL) Waste Acceptance Criteria (WAC)]. At the present, the TWCP does not address remote-handled (RH) waste

Gamma-ray spectrometry combined with acceptable knowledge (GSAK). A technique for characterization of certain remote-handled transuranic (RH-TRU) wastes. Part 2. Testing and results

International Nuclear Information System (INIS)

Hartwell, J.K.; McIlwain, M.E.

2005-01-01

Gamma-ray spectrometry combined with acceptable knowledge (GSAK) is a technique for the characterization of certain remote-handled transuranic (RH-TRU) wastes. GSAK uses gamma-ray spectrometry to quantify a portion of the fission product inventory of RH-TRU wastes. These fission product results are then coupled with calculated inventories derived from acceptable process knowledge to characterize the radionuclide content of the assayed wastes. GSAK has been evaluated and tested through several test exercises. These tests and their results are described; while the former paper in this issue presents the methodology, equipment and techniques. (author)

RETRIEVING SUSPECT TRANSURANIC WASTE FROM THE HANFORD BURIAL GROUNDS PROGRESS PLANS AND CHALLENGES

International Nuclear Information System (INIS)

FRENCH, M.S.

2006-01-01

This paper describes the scope and status of the program for retrieval of suspect transuranic (TRU) waste stored in the Hanford Site low-level burial grounds. Beginning in 1970 and continuing until the late 1980's, waste suspected of containing significant quantities of transuranic isotopes was placed in ''retrievable'' storage in designated modules in the Hanford burial grounds, with the intent that the waste would be retrieved when a national repository for disposal of such waste became operational. Approximately 15,000 cubic meters of waste, suspected of being TRU, was placed in storage modules in four burial grounds. With the availability of the national repository (the Waste Isolation Pilot Plant), retrieval of the suspect TRU waste is now underway. Retrieval efforts, to date, have been conducted in storage modules that contain waste, which is in general, contact-handled, relatively new (1980's and later), is stacked in neat, engineered configurations, and has a relatively good record of waste characteristics. Even with these optimum conditions, retrieval personnel have had to deal with a large number of structurally degraded containers, radioactive contamination issues, and industrial hazards (including organic vapors). Future retrieval efforts in older, less engineered modules are expected to present additional hazards and difficult challenges

Mapping of transuranic elements in soil by nuclear track methodology

International Nuclear Information System (INIS)

Espinosa, G.

2001-01-01

An alternative method is presented to map the distribution of transuranic elements, which is characterized by its simplicity in both implementation and instrumentation. The method is based on the interaction of alpha particles in polymeric materials and the formation of tracks, which become visible after chemical etching. Nuclear track detectors are placed on the soil in order to evaluate the distribution of the radioactive material and its relative intensity for transuranic contaminants. CR-39 polycarbonate was used as a nuclear track detector in this study. Chemical etching was done with a 6.25M KOH solution in a closed system for 16 hours. The readings were performed in an automatic system using digital image analysis. The results show the distribution of the contaminants and their location, identifying the zones with large intensities. This method is attractive for use in areas contaminated with alpha particles, and specially transuranic elements, because it involves in situ measurements, generates very low amounts of radioactive waste, and the detectors are easily handled. (author)

Remote automated material handling of radioactive waste containers

International Nuclear Information System (INIS)

Greager, T.M.

1994-09-01

To enhance personnel safety, improve productivity, and reduce costs, the design team incorporated a remote, automated stacker/retriever, automatic inspection, and automated guidance vehicle for material handling at the Enhanced Radioactive and Mixed Waste Storage Facility - Phase V (Phase V Storage Facility) on the Hanford Site in south-central Washington State. The Phase V Storage Facility, scheduled to begin operation in mid-1997, is the first low-cost facility of its kind to use this technology for handling drums. Since 1970, the Hanford Site's suspect transuranic (TRU) wastes and, more recently, mixed wastes (both low-level and TRU) have been accumulating in storage awaiting treatment and disposal. Currently, the Hanford Site is only capable of onsite disposal of radioactive low-level waste (LLW). Nonradioactive hazardous wastes must be shipped off site for treatment. The Waste Receiving and Processing (WRAP) facilities will provide the primary treatment capability for solid-waste storage at the Hanford Site. The Phase V Storage Facility, which accommodates 27,000 drum equivalents of contact-handled waste, will provide the following critical functions for the efficient operation of the WRAP facilities: (1) Shipping/Receiving; (2) Head Space Gas Sampling; (3) Inventory Control; (4) Storage; (5) Automated/Manual Material Handling

Hanford Site Transuranic (TRU) Waste Certification Plan

International Nuclear Information System (INIS)

GREAGER, T.M.

2000-01-01

As a generator of transuranic (TRU) and TRU mixed waste destined for disposal at the Waste Isolation Pilot Plant (WIPP), the Hanford Site must ensure that its TRU waste meets the requirements of US. Department of Energy (DOE) 0 435.1, ''Radioactive Waste Management,'' and the Contact-Handled (CH) Transuranic Waste Acceptance Criteria for the Waste Isolation Pilot Plant (WIPP-WAC). WIPP-WAC requirements are derived from the WIPP Technical Safety Requirements, WIPP Safety Analysis Report, TRUPACT-II SARP, WIPP Land Withdrawal Act, WIPP Hazardous Waste Facility Permit, and Title 40 Code of Federal Regulations (CFR) 191/194 Compliance Certification Decision. The WIPP-WAC establishes the specific physical, chemical, radiological, and packaging criteria for acceptance of defense TRU waste shipments at WIPP. The WPP-WAC also requires that participating DOE TRU waste generator/treatment/storage sites produce site-specific documents, including a certification plan, that describe their program for managing TRU waste and TRU waste shipments before transferring waste to WIPP. Waste characterization activities provide much of the data upon which certification decisions are based. Waste characterization requirements for TRU waste and TRU mixed waste that contains constituents regulated under the Resource Conservation and Recovery Act (RCRA) are established in the WIPP Hazardous Waste Facility Permit Waste Analysis Plan (WAP). The Hanford Site Quality Assurance Project Plan (QAPjP) (HNF-2599) implements the applicable requirements in the WAP and includes the qualitative and quantitative criteria for making hazardous waste determinations. The Hanford Site must also ensure that its TRU waste destined for disposal at WPP meets requirements for transport in the Transuranic Package Transporter-11 (TRUPACT-11). The US. Nuclear Regulatory Commission (NRC) establishes the TRUPACT-11 requirements in the Safety Analysis Report for the TRUPACT-II Shipping Package (TRUPACT-11 SARP). In

Complications Associated with Long-Term Disposition of Newly-Generated Transuranic Waste: A National Laboratory Perspective

International Nuclear Information System (INIS)

Orchard, B.J.; Harvego, L.A.; Carlson, T.L.; Grant, R.P.

2009-01-01

The Idaho National Laboratory (INL) is a multipurpose national laboratory delivering specialized science and engineering solutions for the U.S. Department of Energy (DOE). Sponsorship of INL was formally transferred to the DOE Office of Nuclear Energy, Science and Technology (NE) by Secretary Spencer Abraham in July 2002. The move to NE, and designation as the DOE lead nuclear energy laboratory for reactor technology, supports the nation's expanding nuclear energy initiatives, placing INL at the center of work to develop advanced Generation IV nuclear energy systems; nuclear energy/hydrogen coproduction technology; advanced nuclear energy fuel cycle technologies; and providing national security answers to national infrastructure needs. As a result of the Laboratory's NE mission, INL generates both contact-handled and remote-handled transuranic (TRU) waste from ongoing operations. Generation rates are relatively small and fluctuate based on specific programs and project activities being conducted; however, the Laboratory will continue to generate TRU waste well into the future in association with the NE mission. Currently, plans and capabilities are being established to transfer INL's contact-handled TRU waste to the Advanced Mixed Waste Treatment Plant (AMWTP) for certification and disposal to the Waste Isolation Pilot Plant (WIPP). Remote-handled TRU waste is currently placed in storage at the Materials and Fuels Complex (MFC). In an effort to minimize future liabilities associated with the INL NE mission, INL is evaluating and assessing options for the management and disposition of all its TRU waste on a real-time basis at time of generation. This paper summarizes near-term activities to minimize future re handling of INL's TRU waste, as well as, potential complications associated with the long-term disposition of newly-generated TRU waste. Potential complications impacting the disposition of INL newly-generated TRU waste include, but are not limited to: (1

Analogs for transuranic elements

International Nuclear Information System (INIS)

Weimer, W.C.; Laul, J.C.; Kutt, J.C.

1981-01-01

A combined theoretical and experimental approach is being used to estimate the long-term environmental and biogeochemical behaviors of selected transuranic elements. The objective of this research is to estimate the effect that long-term (hundreds of years) environmental weathering has on the behavior of the transuranic elements americium and curium. This is achieved by investigating the actual behavior of naturally occurring rare earth elements, especially neodymium, that serve as transuranic analogs. Determination of the analog element behavior provides data that can be used to estimate the ultimate availability to man of transuranic materials released into the environment

Remote Handled TRU Waste Status and Activities and Challenges at the Hanford Site

International Nuclear Information System (INIS)

MCKENNEY, D.E.

2000-01-01

A significant portion of the Department of Energy's forecast volume of remote-handled (RH) transuranic (TRU) waste will originate from the Hanford Site. The forecasted Hanford RH-TRU waste volume of over 2000 cubic meters may constitute over one-third of the forecast inventory of RH-TRU destined for disposal at the Waste Isolation Pilot Plant (WIPP). To date, the Hanford TRU waste program has focused on the retrieval, treatment and certification of the contact-handled transuranic (CH-TRU) wastes. This near-term focus on CH-TRU is consistent with the National TRU Program plans and capabilities. The first shipment of CH-TRU waste from Hanford to the WIPP is scheduled early in Calendar Year 2000. Shipments of RH-TRU from Hanford to the WIPP are scheduled to begin in Fiscal Year 2006 per the National TRU Waste Management Plan. This schedule has been incorporated into milestones within the Hanford Federal Facility Agreement and Consent Order (Tri-Party Agreement). These Tri-Party milestones (designated the ''M-91'' series of milestones) relate to development of project management plans, completion of design efforts, construction and contracting schedules, and initiation of process operations. The milestone allows for modification of an existing facility, construction of a new facility, and/or commercial contracting to provide the capabilities for processing and certification of RH-TRU wastes for disposal at the WIPP. The development of a Project Management Plan (PMP) for TRU waste is the first significant step in the development of a program for disposal of Hanford's RH-TRU waste. This PMP will address the path forward for disposition of waste streams that cannot be prepared for disposal in the Hanford Waste Receiving and Processing facility (a contact-handled, small container facility) or other Site facilities. The PMP development effort has been initiated, and the PMP will be provided to the regulators for their approval by June 30, 2000. This plan will detail the

Evaluation of alternatives for a second-generation transportation system for Department of Energy transuranic waste

International Nuclear Information System (INIS)

1984-01-01

Department of Energy (DOE) waste storage sites will ship their contact-handled (CH) and remote-handled (RH) transuranic (TRU) waste to the Waste Isolation Pilot Plant (WIPP) beginning FY 1989. The CH-TRU waste will be shipped in the Transuranic Package Transported (TRUPACT-I), a new packaging being developed by Sandia National Laboratories, Albuquerque/Transportation Technology Center. Some of the DOE TRU waste, however, might be unsuitable for shipment in TRUPACT-I, and is designated special-shipped (SS) TRU waste. The purposes of this study were to: (1) identify the quantity and characteristics of SS-TRU waste stored and generated at DOE facilities; (2) identify alternatives for managing the SS-TRU waste; and (3) make overall recommendations for managing the SS-TRU waste. Data on quantity and characteristics were gathered through coordinating visits to the sites and extracting information from each site's records. Representatives of DOE organizations and contractors set objectives for managing the SS-TRU waste. Alternative shipping systems were then identified for CH SS-TRU waste and RH SS-TRU waste. Evaluations of these alternatives considered how well they would satisfy each objective, and associated potential problems. The study recommends delaying the decision on how best to transport the CH SS-TRU waste to WIPP until the amount of SS-TRU processed waste in heavy drums is known. These conditions and choices are presented: a relatively small number of processed, heavy drums could be shipped most economically via TRUPACT-I, mixed with lighter drums of unprocessed waste. If a large number of heavy drums is to be shipped, a shorter and narrower version of TRUPACT-I would be preferred alternative. The Defense High-Level Waste cask is the recommended alternative system for shipping RH SS-TRU waste. 12 references, 15 figures, 22 tables

Technology status report: Transuranic contamination control at INEL

International Nuclear Information System (INIS)

Loomis, G.G.

1991-09-01

This report summarizes proposed FY-92 work at the Idaho National Engineering Laboratory (INEL) in the field of contamination control during transuranic waste handling operations. The proposed work is both applied research and demonstration testing. The INEL needs for contamination control applied research and demonstration testing are listed along with a description of past accomplishments. The INEL proposal is compared to other proposals for contamination control work that are under consideration for funding by the Department of Energy. Benefits of this work and impacts of not sponsoring this work are also given. 21 refs

Transuranic solid waste management programs. Progress report, July--December 1975

International Nuclear Information System (INIS)

1976-09-01

Progress is reported for three transuranic solid waste management programs funded at the Los Alamos Scientific Laboratory (LASL) by the Energy Research and Development Administration (ERDA) Division of Fuel Cycle and Production (NFCP). Under the Transuranic Waste Research and Development Program, continued studies have shown the potential attractiveness of fiber drums as an acceptable substitute for the current mild steel storage containers. Various fire retardants have been evaluated, with one indicating significant ability to inhibit fire propagation. Continued radiolysis studies, under laboratory and field conditions, continue to reaffirm earlier LASL results indicating no significant hazard from radiolytic reactions, assuming no change in current allowable loadings. Care must be exercised to differentiate between radiolytic and chemical reactions. Other efforts have identified a modification of chemical processing to reduce the amounts of plutonium requiring retrievable storage. Studies are also in progress to enhance the sensitivity of the LASL MEGAS assay system. The Transuranic-Contaminated Solid Waste Treatment Development Facility building was 72 percent complete as of December 31, 1975, which is in accord with the existing schedule. Procurement of process components is also on schedule. Certain modifications to the facility have been made, and various pre-facility experiments on waste container handling and processing have been completed. The program for the Evaluation of Transuranic-Contaminated Radioactive Waste Disposal Areas continued development of various computer modules for simulation of radionuclide transport within the biosphere. In addition, program staff contributed to an ERDA document on radioactive waste management through the preparation of a report on burial of radioactive waste at ERDA-contractor and commercial sites

Transuranic solid waste management programs. Progress report, July--December 1975

Energy Technology Data Exchange (ETDEWEB)

1976-09-01

Progress is reported for three transuranic solid waste management programs funded at the Los Alamos Scientific Laboratory (LASL) by the Energy Research and Development Administration (ERDA) Division of Fuel Cycle and Production (NFCP). Under the Transuranic Waste Research and Development Program, continued studies have shown the potential attractiveness of fiber drums as an acceptable substitute for the current mild steel storage containers. Various fire retardants have been evaluated, with one indicating significant ability to inhibit fire propagation. Continued radiolysis studies, under laboratory and field conditions, continue to reaffirm earlier LASL results indicating no significant hazard from radiolytic reactions, assuming no change in current allowable loadings. Care must be exercised to differentiate between radiolytic and chemical reactions. Other efforts have identified a modification of chemical processing to reduce the amounts of plutonium requiring retrievable storage. Studies are also in progress to enhance the sensitivity of the LASL MEGAS assay system. The Transuranic-Contaminated Solid Waste Treatment Development Facility building was 72 percent complete as of December 31, 1975, which is in accord with the existing schedule. Procurement of process components is also on schedule. Certain modifications to the facility have been made, and various pre-facility experiments on waste container handling and processing have been completed. The program for the Evaluation of Transuranic-Contaminated Radioactive Waste Disposal Areas continued development of various computer modules for simulation of radionuclide transport within the biosphere. In addition, program staff contributed to an ERDA document on radioactive waste management through the preparation of a report on burial of radioactive waste at ERDA-contractor and commercial sites.

Design, construction, and operation of the contact size reduction facility at the West Valley Demonstration Project

International Nuclear Information System (INIS)

Frank, D.E.; Reeves, S.R.; Valenti, P.J.

1988-05-01

This paper describes the design, construction and initial operation of the Contact-Handled Size Reduction Facility (CSRF) at the West Valley Demonstration Project. The facility was constructed to size reduce contaminated tanks, piping, and other metallic scrap and package the scrap for disposal. In addition, the CSRF has the capability to decontaminate scrap prior to disposal. The anticipated result of decontaminating the scrap is to reduce waste classified as transuranic or low-level Class B and C to Class A or release for unrestricted use as nonradioactive equipment. 10 figs., 1 tab

Transuranic Computational Chemistry.

Science.gov (United States)

Kaltsoyannis, Nikolas

2018-02-26

Recent developments in the chemistry of the transuranic elements are surveyed, with particular emphasis on computational contributions. Examples are drawn from molecular coordination and organometallic chemistry, and from the study of extended solid systems. The role of the metal valence orbitals in covalent bonding is a particular focus, especially the consequences of the stabilization of the 5f orbitals as the actinide series is traversed. The fledgling chemistry of transuranic elements in the +II oxidation state is highlighted. Throughout, the symbiotic interplay of experimental and computational studies is emphasized; the extraordinary challenges of experimental transuranic chemistry afford computational chemistry a particularly valuable role at the frontier of the periodic table. © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Defense Transuranic Waste Program Strategy Document

International Nuclear Information System (INIS)

1984-01-01

The Defense Transuranic Waste Program (DTWP) Strategy Document presents the general strategy for managing transuranic (TRU) waste materials generated during defense and research activities regulated by the US Department of Energy. The Strategy Document includes discussion of objectives and activities relating to the entire Defense Transuranic Waste Program. However, the primary focus is on the specific management responsibilities of the Transuranic Waste Lead Organization (TLO). The document also includes an updated summary of progress on TLO-managed activities over the past year

Idaho National Engineering Laboratory code assessment of the Rocky Flats transuranic waste

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-07-01

This report is an assessment of the content codes associated with transuranic waste shipped from the Rocky Flats Plant in Golden, Colorado, to INEL. The primary objective of this document is to characterize and describe the transuranic wastes shipped to INEL from Rocky Flats by item description code (IDC). This information will aid INEL in determining if the waste meets the waste acceptance criteria (WAC) of the Waste Isolation Pilot Plant (WIPP). The waste covered by this content code assessment was shipped from Rocky Flats between 1985 and 1989. These years coincide with the dates for information available in the Rocky Flats Solid Waste Information Management System (SWIMS). The majority of waste shipped during this time was certified to the existing WIPP WAC. This waste is referred to as precertified waste. Reassessment of these precertified waste containers is necessary because of changes in the WIPP WAC. To accomplish this assessment, the analytical and process knowledge available on the various IDCs used at Rocky Flats were evaluated. Rocky Flats sources for this information include employee interviews, SWIMS, Transuranic Waste Certification Program, Transuranic Waste Inspection Procedure, Backlog Waste Baseline Books, WIPP Experimental Waste Characterization Program (headspace analysis), and other related documents, procedures, and programs. Summaries are provided of: (a) certification information, (b) waste description, (c) generation source, (d) recovery method, (e) waste packaging and handling information, (f) container preparation information, (g) assay information, (h) inspection information, (i) analytical data, and (j) RCRA characterization.

Impact of dynamic certification requirements on the Nuclear Materials Technology Division's transuranic waste management program

International Nuclear Information System (INIS)

Balkey, J.J.; Montoya, A.J.; Wieneke, Ronald E.

2002-01-01

The issuance of the Waste Isolation Pilot Plant's (WIPP) Hazardous Waste Facility Permit in August of 2000, specifically the attachment I3 Waste Analysis Plan (WAP),had a profound impact upon transuranic (TRU) waste certification at Los Alamos National Laboratory's (LANL) Plutonium Facility. Program certification was lost until Laboratory internal program documents could be amended to meet the new WAP requirements, waste management personnel could be retrained to incorporate the changes into waste operations and the entire program successfully pass subsequent Carlsbad Field Ofice (CBFO) audit. This action resulted in the suspension of transuranic waste shipments from LANL to WIPP. In addition the changes unnecessarily increased the complexity of TRU waste program activities in waste handling.

Supplement analysis of transuranic waste characterization and repackaging activities at the Idaho National Engineering Laboratory in support of the Waste Isolation Pilot Plant test program

International Nuclear Information System (INIS)

1991-03-01

This supplement analysis has been prepared to describe new information relevant to waste retrieval, handling, and characterization at the Idaho National Engineering Laboratory (INEL) and to evaluate the need for additional documentation to satisfy the National Environmental Policy Act (NEPA). The INEL proposes to characterize and repackage contact-handled transuranic waste to support the Waste Isolation Pilot Plant (WIPP) Test Phase. Waste retrieval, handling and processing activities in support of test phase activities at the WIPP were addressed in the Supplemental Environmental Impact Statement (SEIS) for the WIPP. To ensure that test-phase wastes are properly characterized and packaged, waste containers would be retrieved, nondestructively examined, and transported from the Radioactive Waste Management Complex (RWMC) to the Hot-Fuel Examination Facility for headspace gas analysis, visual inspections to verify content code, and waste acceptance criteria compliance, then repackaging into WIPP experimental test bins or returned to drums. Following repackaging the characterized wastes would be returned to the RWMC. Waste characterization would help DOE determine WIPP compliance with US Environmental Protection Agency regulations governing disposal of transuranic waste and hazardous waste. Additionally, this program supports onsite compliance with Resource Conservation and Recovery Act (RCRA) requirements, compliance with the terms of the No-Migration Variance at WIPP, and provides data to support future waste shipments to WIPP. This analysis will help DOE determine whether there have been substantial changes made to the proposed action at the INEL, or if preparation of a supplement to the WIPP Final Environmental Impact Statement (DOE, 1980) and SEIS (DOE, 1990a) is required. This analysis is based on current information and includes details not available to the SEIS

Transuranic biokinetic parameters for marine invertebrates--a review.

Science.gov (United States)

Ryan, T P

2002-04-01

A catalogue of biokinetic parameters for the transuranic elements plutonium, americium, curium, neptunium, and californium in marine invertebrates is presented. The parameters considered are: the seawater-animal concentration factor (CF); the sediment-animal concentration ratio (CR); transuranic assimilation efficiency; transuranic tissue distribution and transuranic elimination rates. With respect to the seawater-animal CF, authors differ considerably on how they define this parameter and a seven-point reporting system is suggested. Transuranic uptake from sediment by animals is characterised by low CRs. The assimilation efficiencies of transuranic elements in marine invertebrates are high compared to vertebrates and mammals in general and the distribution of transuranics within the body tissue of an animal is dependent on the uptake path. The elimination of transuranics from most species examined conformed to a standard biphasic exponential model though some examples with three elimination phases were identified.

Transuranic Behavior in Soils and Plants

International Nuclear Information System (INIS)

Wildung, R.E.; Garland, T.R.; Cataldo, D.A.; Rogers, J.E.; McFadden, K.M.; McNair, V.M.; Schreckhise, R.G.

1980-01-01

The principal objectives of these investigations are to determine (1) the potential for alteration of transuranic solubility through formation of transuranic complexes in soil and the role of the soil microflora in this process, (2) the extent of uptake nd translocation by plants and the sites of plant deposition of transuranics or their complexes, (3) the bond types and chemical forms of transuranics or their metabolites in microbes, plant tissues and soils, (4) the influence of soil properties, environmental conditions and cropping on these processes, and (5) the retention of airborne pollutants by plant foliage and their subsequent absorption by leaves and transport to seeds and roots

OXIDATION OF TRANSURANIC ELEMENTS

Science.gov (United States)

Moore, R.L.

1959-02-17

A method is reported for oxidizing neptunium or plutonium in the presence of cerous values without also oxidizing the cerous values. The method consists in treating an aqueous 1N nitric acid solution, containing such cerous values together with the trivalent transuranic elements, with a quantity of hydrogen peroxide stoichiometrically sufficient to oxidize the transuranic values to the hexavalent state, and digesting the solution at room temperature.

Transuranic elements and nuclear wastes

International Nuclear Information System (INIS)

Bowen, V.T.

1974-01-01

The contamination of oceans and marine life by transuranic elements (elements of atomic number greater than 92) is the main concern of this paper. Wastes of three different types, low-level, intermediate-level, and high-level, are considered. Fallout of Pu and other transuranics is discussed as it affects marine biogeochemistry and geochemistry. Different paths of absorption or uptake under various conditions of release are pointed out in some detail. The transfer of radioactivity to mammals from marine sources is considered in some detail. Waste disposal practices at Windscale are reviewed. It is concluded that the problems associated with transuranic wastes in oceans and marine life are very complex. Monitoring of waste release and uptake is concluded to not be enough. Each situation of release of transuranics to the environment should be treated as an experiment and milked for all the information that it can reveal. The tremendous expenditure of money and manpower necessary for such an undertaking is stressed

Transuranic element behavior in soils and plants

International Nuclear Information System (INIS)

Wildung, R.E.

1982-01-01

The principal objective of this study is to define soil, plant, and foliar interaction processes that influence the availability of transuranic elements to agricultural plants and animals as a basis for improved modeling and dose-assessment. Major areas of emphasis are: (1) soil and soil-microbial processes that influence the concentration and form of transuranic elements in soil solutions and availability to the plant root with time; (2) deposition and plant interception of airborne submicronic particles containing transuranic elements and their susceptibility to leaching; (3) plant processes that influence transport across plant root membrane and foliar surfaces, as well as the form and sites of deposition of transuranic elements in mature plants; and (4) the integrated effect of soil and plant processes on transuranic element availability to, and form in, animals that consume plants

Fixation of transuranics with different degrees of oxidation on clays

International Nuclear Information System (INIS)

Billon, A.

1982-01-01

Distribution coefficient (Ksub(d)) measurements available in the literature relate to plutonium, without reference to any particular valence state. It would be of interest to be able to ascertain the behaviour of this element (and the transuranics in general) from the nature of the chemical species taking part in the interaction with a natural or artificial medium (radioactive waste containment barriers). The author cites the results of measurements made for Np(IV), Np(V), Pu(IV), Pu(VI) and Am(III). Two types of clay have been tried out - bentonite and attapulgite. When the transuranic has been oxidized to a suitable degree, preferably by an electrochemical technique, it is brought into contact with a clay suspension. After stirring, decantation and filtration, the transuranic is analysed in the aqueous phase, by photospectrometry when the concentration makes it possible to do so (for NpO 2 + and PuO 2 2+ , which have high molar absorption coefficients epsilon), or else by counting techniques (liquid scintillation and gamma spectrometry). The results are given in the form of graphs (log Ksub(d) = f(pH)) or tables. Emphasis is given to the accuracy and reproducibility of the measurements. The effect of several mineral or organic anions (EDTA) on the retention of Np(V) is considered. An analysis is made of the behaviour of plutonium in accordance with its degree of oxidation. (author)

Overview of DOE's Transuranic Waste Program

International Nuclear Information System (INIS)

McFadden, M.H.; Detamore, J.A.

1987-01-01

The US Department of Energy has assigned to Albuquerque Operations the Defense Transuranic Waste Program responsibility for long-range planning and management of defense transuranic (TRU) waste. The Transuranic Waste Lead Organization (TLO) has divided the Program into seven elements which support it's primary goal of ending interim storage and achieving permanent disposal. These are: waste generation site activities, storage site activities, burial site activities, technology development, transportation, institutional activities, and permanent disposal. This paper will briefly discuss these seven elements and how they are integrated to provide for successful achievement of the primary goal

TRU waste transportation package development

International Nuclear Information System (INIS)

Eakes, R.G.; Lamoreaux, G.H.; Romesberg, L.E.; Sutherland, S.H.; Duffey, T.A.

1980-01-01

Inventories of the transuranic wastes buried or stored at various US DOE sites are tabulated. The leading conceptual design of Type-B packaging for contact-handled transuranic waste is the Transuranic Package Transporter (TRUPACT), a large metal container comprising inner and outer tubular steel frameworks which are separated by rigid polyurethane foam and sheathed with steel plate. Testing of TRUPACT is reported. The schedule for its development is given. 6 figures

Long-term management plan INEL transuranic waste

International Nuclear Information System (INIS)

McKinney, J.D.

1978-12-01

The Idaho National Engineering Laboratory stores large quantities of transuranic-contaminated waste at its Radioactive Waste Management Complex. This report presents a 10-year plan for management of this transuranic waste and includes descriptions of projects involving nuclear waste storage, retrieval, processing, systems analysis, and environmental science. Detailed project schedules and work breakdown charts are provided to give the reader a clear view of transuranic waste management objectives

Overview of DOE's transuranic waste program

International Nuclear Information System (INIS)

McFadden, M.H.; Detamore, J.A.

1988-01-01

The United States Department of Energy (DOE) has assigned to Albuquerque Operations the Defense Transuranic Waste Program (DTWP) responsibility for long-range planning and management for defense transuranic (TRU) waste. The Transuranic Waste Lead Organization (TLO) has divided the Program into seven elements that support its primary goal of ending interim storage and achieving permanent disposal. These elements include waste generation site activities, storage site activities, burial site activities, technology development, transportation, institutional activities and permanent disposal. This paper briefly discusses these seven elements and how they are integrated to provide for successful achievement of the primary goal

Some design aspects of transuranic field studies

International Nuclear Information System (INIS)

Gilbert, R.O.; Eberhardt, L.L.

1977-01-01

In this paper, we discuss some design aspects of transuranic field studies. Some of the principal steps in the design of such studies are given and illustrated using examples. This is followed by a review of sampling designs that have been used at nuclear detonation and safety-shot sites on the Nevada Test Site and elsewhere for estimating spatial pattern and total amounts in soil. Some design aspects of ecosystem-type transuranic studies for estimating total amounts as well as movement of transuranics between ecosystem components are also discussed. Acceptance sampling using either attributes or measurements is considered as a possible approach for deciding whether to clean up a contaminated site. Three general guidelines for the design of efficient transuranic studies are presented

Waste Isolation Pilot Plant (WIPP) conceptual design report. Part I: executive summary. Part II: facilities and system

International Nuclear Information System (INIS)

1977-06-01

The pilot plant is developed for ERDA low-level contact-handled transuranic waste, ERDA remote-handled intermediate-level transuranic waste, and for high-level waste experiments. All wastes placed in the WIPP arrive at the site processed and packaged; no waste processing is done at the WIPP. All wastes placed into the WIPP are retrievable. The proposed site for WIPP lies 26 miles east of Carlsbad, New Mexico. This document includes the executive summary and a detailed description of the facilities and systems

Porous membrane electrochemical cell for uranium and transuranic recovery from molten salt electrolyte

Science.gov (United States)

Willit, James L [Batavia, IL

2010-09-21

An improved process and device for the recovery of the minor actinides and the transuranic elements (TRU's) from a molten salt electrolyte. The process involves placing the device, an electrically non-conducting barrier between an anode salt and a cathode salt. The porous barrier allows uranium to diffuse between the anode and cathode, yet slows the diffusion of uranium ions so as to cause depletion of uranium ions in the catholyte. This allows for the eventual preferential deposition of transuranics present in spent nuclear fuel such as Np, Pu, Am, Cm. The device also comprises an uranium oxidation anode. The oxidation anode is solid uranium metal in the form of spent nuclear fuel. The spent fuel is placed in a ferric metal anode basket which serves as the electrical lead or contact between the molten electrolyte and the anodic uranium metal.

Porous membrane electrochemical cell for uranium and transuranic recovery from molten salt electrolyte

Science.gov (United States)

Willit, James L.

2007-09-11

An improved process and device for the recovery of the minor actinides and the transuranic elements (TRU's) from a molten salt electrolyte. The process involves placing the device, an electrically non-conducting barrier between an anode salt and a cathode salt. The porous barrier allows uranium to diffuse between the anode and cathode, yet slows the diffusion of uranium ions so as to cause depletion of uranium ions in the catholyte. This allows for the eventual preferential deposition of transuranics present in spent nuclear fuel such as Np, Pu, Am, Cm. The device also comprises an uranium oxidation anode. The oxidation anode is solid uranium metal in the form of spent nuclear fuel. The spent fuel is placed in a ferric metal anode basket which serves as the electrical lead or contact between the molten electrolyte and the anodic uranium metal.

PREPD O and VE remote handling system

International Nuclear Information System (INIS)

Theil, T.N.

1985-01-01

The Process Experimental Pilot Plant (PREPP) at the Idaho National Engineering Laboratory is designed for volume reduction and packaging of transuranic (TRU) waste. The PREPP opening and verification enclosure (O and VE) remote handling system, within that facility, is designed to provide examination of the contents of various TRU waste storage containers. This remote handling system will provide the means of performing a hazardous operation that is currently performed manually. The TeleRobot to be used in this system is a concept that will incorporate and develop man in the loop operation (manual mode), standardized automatic sequencing of end effector tools, increased payload and reach over currently available computer-controlled robots, and remote handling of a hazardous waste operation. The system is designed within limited space constraints and an operation that was originally planned, and is currently being manually performed at other plants. The PREPP O and VE remote handling system design incorporates advancing technology to improve the working environment in the nuclear field

Test phase plan for the Waste Isolation Pilot Plant

International Nuclear Information System (INIS)

1993-03-01

The US Department of Energy (DOE) has prepared this Test Phase Plan for the Waste Isolation Pilot Plant to satisfy the requirements of Public Law 102-579, the Waste Isolation Pilot Plant (WIPP) Land Withdrawal Act (LWA). The Act provides seven months after its enactment for the DOE to submit this Plan to the Environmental Protection Agency (EPA) for review. A potential geologic repository for transuranic wastes, including transuranic mixed wastes, generated in national-defense activities, the WIPP is being constructed in southeastern New Mexico. Because these wastes remain radioactive and chemically hazardous for a very long time, the WIPP must provide safe disposal for thousands of years. The DOE is developing the facility in phases. Surface facilities for receiving waste have been built and considerable underground excavations (2150 feet below the surface) that are appropriate for in-situ testing, have been completed. Additional excavations will be completed when they are required for waste disposal. The next step is to conduct a test phase. The purpose of the test phase is to develop pertinent information and assess whether the disposal of transuranic waste and transuranic mixed waste in the planned WIPP repository can be conducted in compliance with the environmental standards for disposal and with the Solid Waste Disposal Act (SWDA) (as amended by RCRA, 42 USC. 6901 et. seq.). The test phase includes laboratory experiments and underground tests using contact-handled transuranic waste. Waste-related tests at WIPP will be limited to contact-handled transuranic and simulated wastes since the LWA prohibits the transport to or emplacement of remote-handled transuranic waste at WIPP during the test phase

Implications of Fast Reactor Transuranic Conversion Ratio

International Nuclear Information System (INIS)

Piet, Steven J.; Hoffman, Edward A.; Bays, Samuel E.

2010-01-01

Theoretically, the transuranic conversion ratio (CR), i.e. the transuranic production divided by transuranic destruction, in a fast reactor can range from near zero to about 1.9, which is the average neutron yield from Pu239 minus 1. In practice, the possible range will be somewhat less. We have studied the implications of transuranic conversion ratio of 0.0 to 1.7 using the fresh and discharge fuel compositions calculated elsewhere. The corresponding fissile breeding ratio ranges from 0.2 to 1.6. The cases below CR=1 ('burners') do not have blankets; the cases above CR=1 ('breeders') have breeding blankets. The burnup was allowed to float while holding the maximum fluence to the cladding constant. We graph the fuel burnup and composition change. As a function of transuranic conversion ratio, we calculate and graph the heat, gamma, and neutron emission of fresh fuel; whether the material is 'attractive' for direct weapon use using published criteria; the uranium utilization and rate of consumption of natural uranium; and the long-term radiotoxicity after fuel discharge. For context, other cases and analyses are included, primarily once-through light water reactor (LWR) uranium oxide fuel at 51 MWth-day/kg-iHM burnup (UOX-51). For CR 1, heat, gamma, and neutron emission decrease with recycling. The uranium utilization exceeds 1%, especially as all the transuranic elements are recycled. exceeds 1%, especially as all the transuranic elements are recycled. At the system equilibrium, heat and gamma vary by somewhat over an order of magnitude as a function of CR. Isotopes that dominate heat and gamma emission are scattered throughout the actinide chain, so the modest impact of CR is unsurprising. Neutron emitters are preferentially found among the higher actinides, so the neutron emission varies much stronger with CR, about three orders of magnitude.

Hanford site transuranic waste sampling plan

International Nuclear Information System (INIS)

GREAGER, T.M.

1999-01-01

This sampling plan (SP) describes the selection of containers for sampling of homogeneous solids and soil/gravel and for visual examination of transuranic and mixed transuranic (collectively referred to as TRU) waste generated at the U.S. Department of Energy (DOE) Hanford Site. The activities described in this SP will be conducted under the Hanford Site TRU Waste Certification Program. This SP is designed to meet the requirements of the Transuranic Waste Characterization Quality Assurance Program Plan (CAO-94-1010) (DOE 1996a) (QAPP), site-specific implementation of which is described in the Hanford Site Transuranic Waste Characterization Program Quality Assurance Project Plan (HNF-2599) (Hanford 1998b) (QAPP). The QAPP defines the quality assurance (QA) requirements and protocols for TRU waste characterization activities at the Hanford Site. In addition, the QAPP identifies responsible organizations, describes required program activities, outlines sampling and analysis strategies, and identifies procedures for characterization activities. The QAPP identifies specific requirements for TRU waste sampling plans. Table 1-1 presents these requirements and indicates sections in this SP where these requirements are addressed

Transuranic behavior in soils and plants

International Nuclear Information System (INIS)

Wildung, R.E.; Garland, T.R.; Cataldo, D.A.; Rogers, J.E.; McFadden, K.M.; Jenne, E.A.; Schreckhise, R.G.

1981-01-01

The principal objective of this study is to gather information about soil, plant, and foliar interaction factors that influence the availability of transuranics to agricultural plants and animals. This paper discusses plant processes which influence transport across the plant root membrane and foliar surfaces, and the form and sites of deposition of transuranic elements in mature plants

Thermometry in dielectrophoresis chips for contact-free cell handling

International Nuclear Information System (INIS)

Jaeger, M S; Mueller, T; Schnelle, T

2007-01-01

Cell biology applications, protocols in immunology and stem cell research, require that individual cells are handled under strict control of their contacts to other cells or synthetic surfaces. Dielectrophoresis (DEP) in microfluidic chips is an established technique to investigate, group, wash, cultivate and sort cells contact-free under physiological conditions: microelectrode octode cages, versatile dielectrophoretic elements energized with radio frequency electric fields, stably trap single cells or cellular aggregates. For medical applications and cell cultivation, possible side effects of the dielectrophoretic manipulation, such as membrane polarization and Joule heating, have to be quantified. Therefore, we characterized the electric field-induced warming in dielectrophoretic cages using ohmic resistance measurements, fluorometry, liquid crystal beads, infra-red thermography and bubble size thermometry. We compare the results of these techniques with respect to the influences of voltage, electric conductivity of buffer, frequency, cage size and electrode surface. We conclude that in the culture medium thermal effects may be neglected if low voltages and an electric field-reducing phase pattern are used. Our experimental results provide explicit values for estimating the thermal effect on dielectrophoretically caged cells and show that Joule heating is best minimized by optimizing the cage geometry and reducing the buffer conductivity. The results may additionally serve to evaluate and improve theoretical predictions on field-induced effects. Based on present-day chip processing possibilities, DEP is well suited for the manipulation of cells

Project plans for transuranic waste at small quantity sites in the Department of Energy comples-10522

International Nuclear Information System (INIS)

Mctaggart, Jerri Lynne; Lott, Sheila; Gadbury, Casey

2009-01-01

Los Alamos National Laboratory, Carlsbad Office (LANL-CO), has been tasked to write Project Plans for all of the Small Quantity Sites (SQS) with defense related Transuranic (TRU) waste in the Department of Energy (DOE) complex. Transuranic Work-Off Plans were precursors to the Project Plans. LANL-CO prepared a Work-Off Plan for each small quantity site. The Work-Off Plan that identified issues, drivers, schedules, and inventory. Eight sites have been chosen to deinventory their legacy TRU waste; Bettis Atomic Power Laboratory, General Electric-Vallecitos Nuclear Center, Lawrence Berkeley National Laboratory, Lawrence Livermore National Laboratory-Area 300, Nevada Test Site, Nuclear Radiation Development, Sandia National Laboratory, and the Separations Process Research Unit. Each plan was written for contact and/or remote handled waste if present at the site. These project plans will assist the small quantity sites to ship legacy TRU waste offsite and de-inventory the site of legacy TRU waste. The DOE is working very diligently to reduce the nuclear foot print in the United States. Each of the eight SQSs will be de-inventoried of legacy TRU waste during a campaign that ends September 2011. The small quantity sites have a fraction of the waste that large quantity sites possess. During this campaign, the small quantity sites will package all of the legacy TRU waste and ship to Idaho or directly to the Waste Isolation Pilot Plant (WIPP) in Carlsbad, New Mexico. The sites will then be removed from the Transuranic Waste Inventory if they are de-inventoried of all waste. Each Project Plan includes the respective site inventory report, schedules, resources, drivers and any issues. These project plans have been written by the difficult waste team and will be approved by each site. Team members have been assigned to each site to write site specific project plans. Once the project plans have been written, the difficult team members will visit the sites to ensure nothing has

Metal and transuranic records in mussel shells, byssal threads and tissues

Science.gov (United States)

Koide, Minoru; Lee, Dong Soo; Goldberg, Edward D.

1982-12-01

Bivalve shells offer several advantages over tissues for the monitoring of heavy metal pollutants in the marine environment. They are easier to handle and to store. The problem of whether to depurate the animals before analyses is avoided. The shells appear to be more sensitive to environmental heavy metals levels over the long term than do the soft parts. Of the substances examined (Cd, Cu, Zn, Pb, Ag, Ni, 238Pu and 239 + 240Pu) only Pb and Pu displayed a strong covariance between soft tissue and shell concentrations. There were strong correlations between metals in the shell but not in the soft tissues in general. The byssal threads, because of their enrichment of transuranic elements and of their ease in handling, may be useful in monitoring these metals. A very weak discharge of 238Pu to marine waters adjacent to a nuclear reactor was detected in the byssal threads of mussels.

A transuranic aerosol measurement system: Preliminary results

International Nuclear Information System (INIS)

Prevo, C.T.; Kaifer, R.C.; Rueppel, D.W.; Delvasto, R.M.; Biermann, A.H.; Phelps, P.L.

1986-10-01

We have completed the design, fabrication, and assembly of a computer-based prototype system for the measurement of transuranic aerosols in the workplace and environment. This system (called WOTAMS for Workplace Transuranic Aerosol Measurement System) incorporates two detectors: (1) an in-line solid-state alpha detector that sends out an alarm the moment a transuranic release occurs, and (2) an in-vacuum detector that increases off-line-analysis sensitivity. The in-line sensitivity of the system is better than 5.0 MPC-h, and the in-vacuum sensitivity exceeds 0.5 MPC-h. 5 refs., 8 figs., 1 tab

Plutonium and other transuranics in small vertebrates: a review

International Nuclear Information System (INIS)

Bradley, W.G.; Moor, K.S.; Naegle, S.R.

1977-01-01

The published data relevant to transuranics in small vertebrates inhabiting terrestrial environments is reviewed. Experimental results indicate that atomic size and valence state affect rates of absorption, transportation, and excretion of transuranics in living systems. Whereas there is a marked tendency for transuranics to hydrolyze to insoluble colloidal products at physiological pH, complexing agents and chelation enhance solubility and transportability. The natural modes of uptake of transuranics by vertebrates include absorption from the gut, the intact or damaged skin, and inhalation. Absorption from the gut into the bloodstream is very low. Potential hazards may exist if complexing or chelating agents are present, if absorption is continuous, or if exposure involves young animals. The intact skin provides an effective barrier to absorption of transuranics. Relatively high levels of absorption may occur when transuranics are administered subcutaneously or intramuscularly, particularly with increased acidity and solubility of the compounds. Inhalation is probably the most hazardous natural route of uptake. Insoluble transuranic compounds are retained in the lung and soluble compounds are transported rapidly via the blood to bone, liver, and other organs. Deposition of plutonium in mammalian gonads resulting in a decrease in spermatogenesis, ovarian damage, and reduced fecundity is documented. The current knowledge of the behavior of transuranics in terrestrial environments is limited. Plutonium and americium uptake by small mammals has been documented. Plutonium body burdens were related to depressed leukocyte count on a statistical basis. Reduced rodent populations in areas of high plutonium concentrations illustrate the problems of evaluating uptake by mobile animals

Intercalibration of transuranic measurements

International Nuclear Information System (INIS)

Fukai, R.; Ballestra, S.; Thein, M.

1982-01-01

One of the major objectives of the coordinated research programme on Transuranic Cycling Behaviour in the Marine Environment has been to achieve the comparability of the measurement results among the laboratories from different countries participating in the programme. In order to fulfil this objective, the intercalibration exercises of transuranic measurements using sea water and sediment samples were organized by the Monaco Laboratory within the duration of the programme in 1979-1981. The sediment and sea water samples were collected respectively by the Bhabha Atomic Research Centre of India and the Hydrographic Institute of the Federal Republic of Germany. In the present report the results of these intercalibration exercises are surveyed

Nuclear-fuel-cycle risk assessment: descriptions of representative non-reactor facilities, Sections 15-19

Energy Technology Data Exchange (ETDEWEB)

Schneider, K.J.

1982-09-01

Information is presented under the following section headings: fuel reprocessing; spent fuel and high-level and transuranic waste storage; spent fuel and high-level and transuranic waste disposal; low-level and intermediate-level waste disposal; and, transportation of radioactive materials in the nuclear fuel cycle. In each of the first three sections a description is given on the mainline process, effluent processing and waste management systems, plant layout, and alternative process schemes. Safety information and a summary are also included in each. The section on transport of radioactive materials includes information on the transportation of uranium ore, uranium ore concentrate, UF/sub 6/, PuO/sub 2/ powder, unirradiated uranium and mixed-oxide fuel assemblies, spent fuel, solidified high-level waste, contact-handled transuranic waste, remote-handled transuranic waste, and low and intermediate level nontransuranic waste. A glossary is included. (JGB)

Nuclear-fuel-cycle risk assessment: descriptions of representative non-reactor facilities, Sections 15-19

International Nuclear Information System (INIS)

Schneider, K.J.

1982-09-01

Information is presented under the following section headings: fuel reprocessing; spent fuel and high-level and transuranic waste storage; spent fuel and high-level and transuranic waste disposal; low-level and intermediate-level waste disposal; and, transportation of radioactive materials in the nuclear fuel cycle. In each of the first three sections a description is given on the mainline process, effluent processing and waste management systems, plant layout, and alternative process schemes. Safety information and a summary are also included in each. The section on transport of radioactive materials includes information on the transportation of uranium ore, uranium ore concentrate, UF 6 , PuO 2 powder, unirradiated uranium and mixed-oxide fuel assemblies, spent fuel, solidified high-level waste, contact-handled transuranic waste, remote-handled transuranic waste, and low and intermediate level nontransuranic waste. A glossary is included

Recoverable immobilization of transuranic elements in sulfate ash

Science.gov (United States)

Greenhalgh, Wilbur O.

1985-01-01

Disclosed is a method of reversibly immobilizing sulfate ash at least about 20% of which is sulfates of transuranic elements. The ash is mixed with a metal which can be aluminum, cerium, samarium, europium, or a mixture thereof, in amounts sufficient to form an alloy with the transuranic elements, plus an additional amount to reduce the transuranic element sulfates to elemental form. Also added to the ash is a fluxing agent in an amount sufficient to lower the percentage of the transuranic element sulfates to about 1% to about 10%. The mixture of the ash, metal, and fluxing agent is heated to a temperature sufficient to melt the fluxing agent and the metal. The mixture is then cooled and the alloy is separated from the remainder of the mixture.

Modeling of a dissolution system for transuranic compounds

International Nuclear Information System (INIS)

Chiba, Z.; Dease, C.

1991-02-01

A system is currently being developed at Lawrence Livermore Laboratory to treat transuranic wastes by means of a mediated electrochemical oxidation process. The process involves generating Ag( ++ ) from a solution of silver nitrate and nitric acid in an electrochemical cell. Ag( ++ ) is highly reactive and is capable of attacking many organic and inorganic substances. In particular, if a mixture of particles containing transuranic and other scrap metal oxides is allowed to react with Ag( ++ ) in a nitric acid solution, the transuranic oxides will dissolve and can be removed with the solution leaving the other insoluble oxides behind. The dissolution of the transuranic oxides by reactions with Ag( ++ ) occurs due to further oxidation to higher valence states and the formation of soluble ions such as MO 2 + and MO 2 ++ . 7 refs., 5 figs., 1 tab

2. Transuranic elements

International Nuclear Information System (INIS)

Anon.

1975-01-01

Methods of sample collection, sample storage, sample procedures and radioanalytical procedures for transuranic elements in marine environment are reviewed and recommended. Alpha spectrometry and scintillation techniques are used for measurement of isotopic content. Separation processes for samples are described

Transuranic Storage Area (TSA)-3 container storage unit RCRA closure plan

International Nuclear Information System (INIS)

Barry, G.A.; Lodman, D.L.; Spry, M.J.; Poor, K.J.

1992-11-01

This document describes the proposed plan for closure of the Transuranic Storage Area (TSA)-3 container storage unit at the Idaho National Engineering Laboratory in accordance with the Resource Conservation and Recovery Act closure requirements. The location, size, capacity, history, and current status of the unit are described. The unit will be closed by decontaminating structures and equipment that may have contacted waste. Sufficient sampling and documentation of all activities will be performed to demonstrate clean closure. A tentative schedule is provided in the form of a milestone chart

Distribution of transuranic nuclides in Mediterranean ecosystems

International Nuclear Information System (INIS)

Ballestra, S.; Thein, M.; Fukai, R.

1982-01-01

For the comprehensive understanding of the behaviour of transuranic elements in the marine environment, the knowledge on the distribution of these elements in various components of marine ecosystems is essential. Since the Mediterranean Sea is considered a sufficiently self-contained system, our approach for studying the processes controlling the transuranic cycling in the sea has been to follow, step by step, the redistribution of plutonium and americium in different components of the marine environment, taking Mediterranean ecosystems as examples. While the studies in the past years have supplied quantitative information on the inputs of plutonium and americium into the Mediterranean from atmospheric fallout and rivers as well as on their behaviour in the Mediterranean water column, only scattered data have been made available so far on the occurrence of the transuranic nuclides in the Mediterranean marine biota or sediments. In order to fill up this information gap, biological and sediment samples were collected from the northwestern Mediterranean region during 1975-1978 for the transuranic measurements. The results of these determinations are given in the present report

Optimizing transuranic waste management-challenges and opportunities

International Nuclear Information System (INIS)

Triay, I.R.; Wu, C.F.; Moody, D.C.; Jennings, S.G.

2002-01-01

The opening of the Waste Isolation Pilot Plant (WIPP) for disposal of transuranic (TRU) waste in March of 1999, the granting of the Hazardous Waste Facility Permit in November 1999, and over two years of operational experience have demonstrated the Department of Energy's (DOE'S) capability in closing the nuclear energy cycle. While these achievements resolved several scientific, engineering, regulatory and political issues, the DOE has identified a new set of challenges that represent opportunities for improving programmatic efficiency, cost-effectiveness, and operational safety in managing the nation's TRU waste. The DOE has recognized that the complex administrative and regulatory requirements for characterization, transportation and disposal of TRU waste are costly (1). A review by the National Academy of Sciences (NAS) states that these requirements lead to inefficient waste characterization, handling and transportation operations that in turn can lead to unnecessary radiation exposure to workers without a commensurate decrease in risk to the public and the environment (2). This paper provides an overview of the status of the WJPP repository, explains the principles of the proposed commercial business approach, and describes some of the proposed major enhancements of the TRU waste transportation systems. The DOE is developing a remote-handled (RH) waste program to enable emplacement of RH waste at WPP. This program includes appropriate facility modifications and regulatory changes (3).

Treatment strategies for transuranic wastes

International Nuclear Information System (INIS)

Schneider, K.J.; Swanson, J.L.; Ross, W.A.; Allen, R.P.; Yasutake, K.M.

1986-01-01

This paper presents an analysis of treatment options or strategies for transuranic wastes expected to be generated at a commercial nuclear fuel reprocessing plant. Six potential options were analyzed, ranging from no treatment to maximum volume reduction and high quality waste forms. Economics for the total management of these (treatment, transportation, disposal) indicate life-cycle savings for extensive treatment are as high as $1.7 billion for 70,000 MTU. Evaluations of the waste processing and waste forms support the selection of a number of the extensive waste treatments. It is concluded that there are significant incentives for extensive treatment of transuranic wastes

A Little Here, A Little There, A Fairly Big Problem Everywhere: Small Quantity Site Transuranic Waste Disposition Alternatives

International Nuclear Information System (INIS)

Luke, Dale Elden; Parker, Douglas Wayne; Moss, J.; Monk, Thomas Hugh; Fritz, Lori Lee; Daugherty, B.; Hladek, K.; Kosiewicx, S.

2000-01-01

Small quantities of transuranic (TRU) waste represent a significant challenge to the waste disposition and facility closure plans of several sites in the Department of Energy (DOE) complex. This paper presents the results of a series of evaluations, using a systems engineering approach, to identify the preferred alternative for dispositioning TRU waste from small quantity sites (SQSs). The TRU waste disposition alternatives evaluation used semi-quantitative data provided by the SQSs, potential receiving sites, and the Waste Isolation Pilot Plant (WIPP) to select and recommend candidate sites for waste receipt, interim storage, processing, and preparation for final disposition of contact-handled (CH) and remote-handled (RH) TRU waste. The evaluations of only four of these SQSs resulted in potential savings to the taxpayer of $33 million to $81 million, depending on whether mobile systems could be used to characterize, package, and certify the waste or whether each site would be required to perform this work. Small quantity shipping sites included in the evaluation included the Battelle Columbus Laboratory (BCL), University of Missouri Research Reactor (MURR), Energy Technology Engineering Center (ETEC), and Mound. Candidate receiving sites included the Idaho National Engineering and Environmental Laboratory (INEEL), the Savannah River Site (SRS), Los Alamos National Laboratory (LANL), Oak Ridge (OR), and Hanford. At least 14 additional DOE sites having TRU waste may be able to save significant money if cost savings are similar to the four evaluated thus far

A little here, a little there, a fairly big problem everywhere: Small-quantity-site transuranic waste disposition alternatives

International Nuclear Information System (INIS)

D. Luke; D. Parker; J. Moss; T. Monk; L. Fritz; B. Daugherty; K. Hladek; S. Kosiewicx

2000-01-01

Small quantities of transuranic (TRU) waste represent a significant challenge to the waste disposition and facility closure plans of several sites in the Department of Energy (DOE) complex. This paper presents the results of a series of evaluations, using a systems engineering approach, to identify the preferred alternative for dispositioning TRU waste from small quantity sites (SQSs). The TRU waste disposition alternatives evaluation used semi-quantitative data provided by the SQSs, potential receiving sites, and the Waste Isolation Pilot Plant (WIPP) to select and recommend candidate sites for waste receipt, interim storage, processing, and preparation for final disposition of contact-handled (CH) and remote-handled (RH) TRU waste. The evaluations of only four of these SQSs resulted in potential savings to the taxpayer of $33 million to $81 million, depending on whether mobile systems could be used to characterize, package, and certify the waste or whether each site would be required to perform this work. Small quantity shipping sites included in the evaluation included the Battelle Columbus Laboratory (BCL), University of Missouri Research Reactor (MURR), Energy Technology Engineering Center (ETEC), and Mound Laboratory. Candidate receiving sites included the Idaho National Engineering and Environmental Laboratory (INEEL), the Savannah River Site (SRS), Los Alamos National Laboratory (LANL), Oak Ridge (OR), and Hanford. At least 14 additional DOE sites having TRU waste may be able to save significant money if cost savings are similar to the four evaluated thus far

Transuranic radionuclides dispersed into the aquatic environment, a bibliography

Energy Technology Data Exchange (ETDEWEB)

Noshkin, V.E.; Stoker, A.C.; Wong, Kai M. [and others

1994-04-01

The purpose of this project was to compile a bibliography of references containing environmental transuranic radionuclide data. Our intent was to identify those parameters affecting transuranic radionuclide transport that may be generic and those that may be dependent on chemical form and/or environmental conditions (i.e., site specific) in terrestrial, aquatic and atmospheric environments An understanding of the unique characteristics and similarities between source terms and environmental conditions relative to transuranic radionuclide transport and cycling will provide the ability to assess and predict the long term impact on man and the environment. An additional goal of our literature review, was to extract the ranges of environmental transuranic radionuclide data from the identified references for inclusion in a data base. Related to source term, these ranges of data can be used to calculate the dose to man from the radionuclides, and to perform uncertainty analyses on these dose assessments. On the basis of our reviews, we have arbitrarily outlined five general source terms. These are fallout, fuel cycle waste, accidents, disposal sites and resuspension. Resuspension of the transuranic radionuclides is a unique source term, in that the radionuclides can originate from any of the other source terms. If these transuranic radionuclides become resuspended into the air, they then become important as a source of inhaled radionuclides.

Management feature of transuranic for HTGR and LWR

International Nuclear Information System (INIS)

Wei Jinfeng; Li Fu; Sun Yuliang

2013-01-01

Long-lived actinides from spent fuels can cause potential long-term environ- mental hazards. The generation and incineration of transuranic in different closed fuel cycles were studied. U and Pu were recycled from spent fuel in the 250 MW high-temperature gas-cooled reactor-pebble-bed-module (HTR-PM) U-Pu fuelled core, and then PuO 2 and MOX fuel elements were designed based on this recycled U and Pu. These fuel elements were used to build up a new PuO 2 or MOX fuelled core with the same geometry of the original reactor. Characteristics of transuranic incineration with HTGR open and closed fuel cycles were studied with VSOP code, and the corresponding results from the light water reactor were compared and analyzed. The transuranic generation with HTGR open fuel cycle is almost half of the corresponding result of the light water reactor. Thus, HTGR closed fuel cycles can effectively burn transuranic. (authors)

Experimental Validation of a Differential Variational Inequality-Based Approach for Handling Friction and Contact in Vehicle

Science.gov (United States)

2015-11-20

terrain modeled using the discrete element method (DEM). Experimental Validation of a Differential Variational Inequality -Based Approach for Handling...COVERED 00-00-2015 to 00-00-2015 4. TITLE AND SUBTITLE Experimental Validation of a Differential Variational Inequality -Based Approach for...sinkage, and single wheel tests. 1.1. Modeling Frictional Contact Via Differential Variational Inequalities Consider a three dimensional (3D) system of

A Contact Pressure Analysis Comparing an All-Inside and Inside-Out Surgical Repair Technique for Bucket-Handle Medial Meniscus Tears.

Science.gov (United States)

Marchetti, Daniel Cole; Phelps, Brian M; Dahl, Kimi D; Slette, Erik L; Mikula, Jacob D; Dornan, Grant J; Bucci, Gabriella; Turnbull, Travis Lee; Singleton, Steven B

2017-10-01

To directly compare effectiveness of the inside-out and all-inside medial meniscal repair techniques in restoring native contact area and contact pressure across the medial tibial plateau at multiple knee flexion angles. Twelve male, nonpaired (n = 12), fresh-frozen human cadaveric knees underwent a series of 5 consecutive states: (1) intact medial meniscus, (2) MCL tear and repair, (3) simulated bucket-handle longitudinal tear of the medial meniscus, (4) inside-out meniscal repair, and (5) all-inside meniscal repair. Knees were loaded with a 1,000-N axial compressive force at 5 knee flexion angles (0°, 30°, 45°, 60°, 90°), and contact area, mean contact pressure, and peak contact pressure were calculated using thin film pressure sensors. No significant differences were observed between the inside-out and all-inside repair techniques at any flexion angle for contact area, mean contact pressure, and peak contact pressure (all P > .791). Compared with the torn meniscus state, inside-out and all-inside repair techniques resulted in increased contact area at all flexion angles (all P contact pressure at all flexion angles (all P contact pressure at all flexion angles (all P contact area and peak contact pressure between the intact state and inside-out technique at angles ≥45° (all P contact area at 60° and 90° and peak contact pressure at 90° (both P contact area, mean contact pressure, and peak contact pressure over the tested flexion angles ranged from 498 to 561 mm 2 , 786 to 997 N/mm 2 , and 1,990 to 2,215 N/mm 2 , respectively. Contact area, mean contact pressure, and peak contact pressure were not significantly different between the all-inside and inside-out repair techniques at any tested flexion angle. Both techniques adequately restored native meniscus biomechanics near an intact level. An all-inside repair technique provided similar, native-state-restoring contact mechanics compared with an inside-out repair technique for the treatment of

Treatment strategies for transuranic wastes

International Nuclear Information System (INIS)

Schneider, K.J.; Ross, W.A.; Swanson, J.L.; Allen, R.P.; Yasutake, K.M.

1986-01-01

This paper presents an analysis of treatment options or strategies for transuranic wastes expected to be generated at a commercial nuclear fuel reprocessing plant. Six potential options were analyzed, ranging from no treatment to maximum volume reduction and high quality waste forms. Economics for the total management of these wastes (treatment, transportation, disposal) indicate life-cycle savings for extensive treatment are as high as $1.7 billion for 70,000 MTU. Evaluations of the waste processing and waste forms support the selection of a number of the extensive waste treatments. It is concluded that there are significant incentives for extensive treatment of transuranic wastes

Demonstration of remotely operated TRU waste size reduction and material handling equipment

International Nuclear Information System (INIS)

Looper, M.G.; Charlesworth, D.L.

1988-01-01

The Savannah River Laboratory (SRL) is developing remote size reduction and material handling equipment to prepare 238 Pu contaminated waste for permanent disposal at the Waste Isolation Pilot Plant (WIPP) in New Mexico. The waste is generated at the Savannah River Plant (SRP) from normal operation and decommissioning activity and is retrievably stored onsite. A Transuranic Waste Facility for preparing, size-reducing, and packaging this waste for disposal is scheduled for completion in 1995. A cold test facility for demonstrating the size reduction and material handling equipment was built, and testing began in January 1987. 9 figs., 1 tab

Transuranic elements in terrestrial animals and the environment: an introduction

International Nuclear Information System (INIS)

Potter, G.D.

1977-01-01

This discussion provides background information to the session on the ''Transuranic Elements in Terrestrial Animals.'' Briefly outlined are some of the historical events leading to the introduction and dispersion of the transuranic elements into the biosphere, to the establishment of the Nevada Applied Ecology Group (NAEG), and to the studies conducted by the Environmental Monitoring and Support Laboratory (EMSL-LV) and the University of Nevada-Las Vegas involving the transuranics distributed by the ''safety shots'' and the nuclear weapons testing program at the Nevada Test Site and the Tonopah Test Range. These studies are described in relation to the overall objectives of the NAEG program. Other potential sources of the transuranic radionuclides are also discussed

Exploitation of a Breakthrough in Magnetic Confinement Fusion to Improve Transuranic Incineration

Energy Technology Data Exchange (ETDEWEB)

Schneider, Erich [Nuclear and Radiation Engineering Program, The University of Texas at Austin, Austin, TX 78712 (United States); Kotschenreuther, Mike; Mahajan, Swadesh; Valanju, Prashant [Institute for Fusion Studies, The University of Texas at Austin, Austin, TX 78712 (United States)

2009-06-15

A fusion-assisted transmutation system for the destruction of transuranic nuclear waste is developed by combining a subcritical fusion-fission hybrid assembly uniquely equipped to burn the worst thermal non-fissile transuranic isotopes with a new fuel cycle that uses cheaper light water reactors for most of the transmutation. The centerpiece of this fuel cycle, the high power density compact fusion neutron source (CFNS, 100 MW, outer radius <3 m), is made possible by a new divertor with a heat-handling capacity five times that of the standard alternative. The number of hybrids needed to destroy a given amount of waste is about an order of magnitude below the corresponding number of critical fast spectrum reactors (FR) as the latter cannot fully exploit the new fuel cycle. Also, the time needed for 99% transuranic waste destruction reduces from centuries (with FR) to decades. The generic Hybrid, combining neutron-rich fusion with energy-rich fission, was first conceptualized several decades ago. However, it is only now that accumulated advances in fusion science and technology allow designing a neutron source like CFNS that is simultaneously compact and high power density, offering a neutron source an order of magnitude stronger than that obtained from accelerator driven systems. The former is essential for efficient coupling to the fission blanket, and the latter is key to efficient neutron production necessary to yield high neutron fluxes needed for effective transmutation. The recent invention of the SuperX-Divertor (SXD)1, a new magnetic configuration that allows the system to safely exhaust large heat and particle fluxes peculiar to CFNS-like devices, is a crucial addition to the underlying knowledge base. The subcritical FFTS acquires a definite advantage over the critical FR approach because of its ability to support an innovative fuel cycle that makes the cheaper LWR do the bulk (75%) of the transuranic transmutation via deep burn in an inert matrix fuel

Engineering considerations for the Waste Isolation Pilot Plant

International Nuclear Information System (INIS)

Scully, L.W.

1978-01-01

The WIPP, located at Los Medanos in New Mexico, is to be used for DOE transuranic and high-level defense wastes. On the surface, there are contact-handled and remote-handled waste facilities. Package size, delivery rates, shipping, shielding and thermal considerations, underground transport and emplacement, retrievability, ventilation, and hoist conveyence safety are discussed

Biological effects of transuranic elements in the environment: human effects and risk estimates

International Nuclear Information System (INIS)

Thompson, R.C.; Wachholz, B.W.

1980-01-01

The potential for human effects from environmentally dispersed transuranic elements is briefly reviewed. Inhalation of transuranics suspended in air and ingestion of transuranics deposited on or incorporated in foodstuffs are the significant routes of entry. Inhalation is probably the more important of these routes because gastrointestinal absorption of ingested transuranics is so inefficient. Major uncertainties are those concerned with substantially enhanced absorption by the very young and the possibility of increased availability as transuranics become incorporated in biological food chains

Central waste complex interim safety basis

International Nuclear Information System (INIS)

Cain, F.G.

1995-01-01

This interim safety basis provides the necessary information to conclude that hazards at the Central Waste Complex are controlled and that current and planned activities at the CWC can be conducted safely. CWC is a multi-facility complex within the Solid Waste Management Complex that receives and stores most of the solid wastes generated and received at the Hanford Site. The solid wastes that will be handled at CWC include both currently stored and newly generated low-level waste, low-level mixed waste, contact-handled transuranic, and contact-handled TRU mixed waste

Transuranic elements in marine environments

International Nuclear Information System (INIS)

Bowen, V.T.

1975-04-01

Transuranic elements are present in marine environments as a result of worldwide fallout, close-in fallout, the SNAP-9A burnup, pipeline disposal of reprocessing wastes, neutron capture by uranium in one-pass cooling-water reactors and the B-52 crash in Thule, Greenland. Distributions and movements of 239 Pu, 240 Pu, 241 Am, and 137 Cs from these introductions in the Atlantic Ocean are being studied partly because the transuranic elements themselves are geochemically interesting, partly because they appear to serve as tracers for specific oceanographic processes, and partly because of concern that man is faced with the problem of disposal of rapidly increasing amounts of transuranics as radioactive waste, and that we must be able, soon, to predict the fates and the effects of those amounts that reach the coastal waters or the deep oceans. Plutonium and americium are widely distributed in the oceans as a result of man's activities. Both appear to be more mobile than expected, and Pu shows little behavior in these environments that had been predicted from laboratory studies. Although their associations with biological material seem to be most striking for rooted plants or Sargassum, it is too premature to dismiss the possibility of their being a real hazard to marine life

Alternative disposal options for transuranic waste

International Nuclear Information System (INIS)

Loomis, G.G.

1994-01-01

Three alternative concepts are proposed for the final disposal of stored and retrieved buried transuranic waste. These proposed options answer criticisms of the existing U.S. Department of Energy strategy of directly disposing of stored transuranic waste in deep, geological salt formations at the Waste Isolation Pilot Plant (WIPP) in Carlsbad, New Mexico. The first option involves enhanced stabilization of stored waste by thermal treatment followed by convoy transportation and internment in the existing WIPP facility. This concept could also be extended to retrieved buried waste with proper permitting. The second option involves in-state, in situ internment using an encapsulating lens around the waste. This concept applies only to previously buried transuranic waste. The third option involves sending stored and retrieved waste to the Nevada Test Site and configuring the waste around a thermonuclear device from the U.S. or Russian arsenal in a specially designed underground chamber. The thermonuclear explosion would transmute plutonium and disassociate hazardous materials while entombing the waste in a national sacrifice area

Brief summary of slag handling options reviewed for the slagging pyrolysis incinerator in the transuranic waste treatment facility (TWIF) at the INEL

International Nuclear Information System (INIS)

Darnell, G.R.

1980-06-01

This report summarizes the technical problems associated with molten transuranic waste slag as it flows from the incinerator shaft (gasifier) of the slagging pyrolysis incinerator. It addresses essential gasifier seals, slag casting and pouring technology, and transportation and packaging problems. Areas requiring further study and testing are identified

FY-1981 project status for the Transuranic Waste Treatment Facility

International Nuclear Information System (INIS)

Benedetti, R.L.; Tait, T.D.

1981-11-01

The primary objective of the Transuranic Waste Treatment Facility (TWTF) Project is to provide a facility to process low-level transuranic waste stored at the Idaho National Engineering Laboratory (INEL) into a form acceptable for disposal at the Waste Isolation Pilot Plant. This report provides brief summary descriptions of the project objectives and background, project status through FY-1981, planned activities for FY-1982, and the EG and G TWTF Project office position on processing INEL transuranic waste

Project B-589, 300 Area transuranic waste interim storage project engineering study

International Nuclear Information System (INIS)

Greenhalgh, W.O.

1985-08-01

The purpose of the study was to look at various alternatives of taking newly generated, remote-handled transuranic waste (caisson waste) in the 300 Area, performing necessary transloading operations and preparing the waste for storage. The prepared waste would then be retrieved when the Waste Isolation Pilot Plant becomes operational and transshipped to the repository in New Mexico with a minimum of inspection and packaging. The scope of this study consisted of evaluating options for the transloading of the TRU wastes for shipment to a 200 Area storage site. Preconceptual design information furnished as part of the engineering study is listed below: produce a design for a clean, sealed waste canister; hot cell loadout system for the waste; in-cell loading or handling equipment; determine transshipment cask options; determine assay system requirements (optional); design or specify transport equipment required; provide a SARP cost estimate; determine operator training requirements; determine waste compaction equipment needs if desirable; develop a cost estimate and approximate schedule for a workable system option; and update the results presented in WHC Document TC-2025

Chemical behaviour of transuranic elements in the natural environment

International Nuclear Information System (INIS)

Kim, J.I.

1991-01-01

The chemical behaviour of transuranic elements in natural aquifer systems is governed by a variety of geochemical reactions, such as dissolution reaction (solubility), hydrolysis, complexation with inorganics or organics, redox reaction, colloid formation, geochemical interaction with surfaces of various minerals, coprecipitation, mineralisation etc. This paper reviews the present state of knowledge on some of these particular reactions. The emphasis is placed on how the individual reactions can be appraised for the long-term prediction of the geochemical behaviour of transuranic elements in the natural environment. Of the various reactions, the primary thermodynamic processes of dissolution of transuranic compounds in aquatic solution, complexation with important anions present in groundwater and colloid generation are discussed with notable examples. Various laser spectroscopy in use for the chemical speciation are mentioned briefly as for their spectroscopic capability as well as applicability. The present review discussion is primarily directed to a better understanding of the migration behaviour of transuranic elements in natural aquifer systems. (author) 100 refs

Determination of Waste Isolation Pilot Plant (WIPP) management and institutional requirements documents for contact-handled (CH) critical systems

International Nuclear Information System (INIS)

1990-01-01

This document lists the critical requirements documents applicable to the receipt of contact-handled waste at the Waste Isolation Pilot Plant. It also describes the processes used to determine the applicability of each document. This analysis is based on the applicable documents that were in effect in the February 1988 time frame. 2 refs

Distribution of transuranic nuclides in soils: a review

International Nuclear Information System (INIS)

Essington, E.H.; Fowler, E.B.

1976-01-01

The literature is reviewed to ascertain the degree of movement and the distribution patterns for transuranic and uranium nuclides in soils. Typical plutonium and uranium profiles are presented and an attempt is made to identify unique characteristics causing deviation from an ideal distribution pattern. By far most of the distribution observations are with plutonium and little is reported for uranium and other transuranic nuclides

Pre-1970 transuranic solid waste at the Hanford Site

International Nuclear Information System (INIS)

Greenhalgh, W.O.

1995-01-01

The document is based on a search of pre-1970 Hanford Solid Waste Records. The available data indicates seven out of thirty-one solid waste burial sites used for pre-1970 waste appear to be Transuranic (TRU). A burial site defined to be TRU contains >100 nCi/gm Transuranic nuclides

Transuranic waste characterization sampling and analysis plan

International Nuclear Information System (INIS)

1994-01-01

Los Alamos National Laboratory (the Laboratory) is located approximately 25 miles northwest of Santa Fe, New Mexico, situated on the Pajarito Plateau. Technical Area 54 (TA-54), one of the Laboratory's many technical areas, is a radioactive and hazardous waste management and disposal area located within the Laboratory's boundaries. The purpose of this transuranic waste characterization, sampling, and analysis plan (CSAP) is to provide a methodology for identifying, characterizing, and sampling approximately 25,000 containers of transuranic waste stored at Pads 1, 2, and 4, Dome 48, and the Fiberglass Reinforced Plywood Box Dome at TA-54, Area G, of the Laboratory. Transuranic waste currently stored at Area G was generated primarily from research and development activities, processing and recovery operations, and decontamination and decommissioning projects. This document was created to facilitate compliance with several regulatory requirements and program drivers that are relevant to waste management at the Laboratory, including concerns of the New Mexico Environment Department

Environmental and other evaluations of alternatives for management of defense transuranic waste at the Idaho National Engineering Laboratory. Volume 1 of 2

International Nuclear Information System (INIS)

1982-04-01

The US Department of Energy (DOE) is responsible for developing and implementing methods for the safe and environmentally acceptable disposal of radioactive wastes. In connection with this responsibility, the DOE is formulating a program for the long-term management of transuranic (TRU) waste buried and stored at the Idaho National Engineering Laboratory (INEL). This report has been prepared to document the results of environmental and other evaluations for three decisions that the DOE is considering: (1) the selection of a general method for the long-term management of the buried TRU waste; (2) the selection of a method for processing the stored waste and for processing the buried waste, if it is retrieved; (3) the selection of a location for the waste-processing facility. This document pertains only to the contact-handled TRU waste buried in pits and trenches and the contact-handled TRU waste held in aboveground storage at the INEL. A decision has previously been made on a method for the long-term management of the stored waste; it will be retrieved and shipped to the Waste Isolation Pilot Plant (WIPP) near Carlsbad, New Mexico. The WIPP is also used in this report as a reference repository for evaluation purposes for the buried waste. This report is contained in two volumes. Volume I is arranged as follows: the summary is an overview of the analyses contained in this document. Section 1 is a statement of the underlying purpose and need to which the report is responding. Section 2 describes the alterntives. Section 3 describes the affected environment at the INEL and the WIPP sites. Section 4 analyzes the environmental effects of each alternative. The appendices in Volume II contain data and discussions supporting the material presented in Volume I

Solid Waste Processing Center Primary Opening Cells Systems, Equipment and Tools

Energy Technology Data Exchange (ETDEWEB)

Bailey, Sharon A.; Baker, Carl P.; Mullen, O Dennis; Valdez, Patrick LJ

2006-04-17

This document addresses the remote systems and design integration aspects of the development of the Solid Waste Processing Center (SWPC), a facility to remotely open, sort, size reduce, and repackage mixed low-level waste (MLLW) and transuranic (TRU)/TRU mixed waste that is either contact-handled (CH) waste in large containers or remote-handled (RH) waste in various-sized packages.

National transuranic program plan

International Nuclear Information System (INIS)

1994-01-01

As a result of various program initiatives, the U.S. generated and will continue to generate waste contaminated with radioactive materials. Because of increased awareness of the risks and special requirements to safely manage long-lived alpha-emitting radionuclides, a new category of radioactive waste, transuranic (TRU) waste, was adopted in 1970. Heads of Field Elements can determine that other alpha-contaminated wastes, peculiar to a specific site, must be managed as transuranic wasteclose quotes. TRU waste is generated and stored at various DOE sites around the country. In December 1993, the National Transuranic Program Office (NTPO) was established as part of the Carlsbad Area Office (CAO) to integrate and coordinate the diverse organizational elements that contribute to the complex-wide management of TRU waste. Numerous sites with small TRU waste inventories are also part of the national TRU waste system. The majority of TRU waste is also contaminated with hazardous materials and is thus considered mixed waste. Mixed waste must be managed in compliance with all federal, state, and local regulations that are applicable to the radioactive and/or hazardous component of the waste. Each generator site is responsible for the management of its respective waste. Sites must plan and implement programs to minimize, characterize, package, treat, store, ship, and dispose of all TRU waste; construct required waste management facilities and equipment; obtain permits; perform site-specific National Environmental Policy Act (NEPA) analyses; conduct environmental studies; perform laboratory analyses; and certify that waste meets appropriate disposal facility criteria. Due to the toxicity and long half-lives of TRU radionuclides, TRU waste must be disposed in a manner that offers greater confinement than shallow land burial

Transuranic contaminated waste form characterization and data base

International Nuclear Information System (INIS)

McArthur, W.C.; Kniazewycz, B.G.

1980-07-01

This report outlines the sources, quantities, characteristics and treatment of transuranic wastes in the United States. This document serves as part of the data base necessary to complete preparation and initiate implementation of transuranic wastes, waste forms, waste container and packaging standards and criteria suitable for inclusion in the present NRC waste management program. No attempt is made to evaluate or analyze the suitability of one technology over another. Indeed, by the nature of this report, there is little critical evaluation or analysis of technologies because such analysis is only appropriate when evaluating a particular application or transuranic waste streams. Due to fiscal restriction, the data base is developed from a myriad of technical sources and does not necessarily contain operating experience and the current status of all technologies. Such an effort was beyond the scope of this report

Transuranic contaminated waste form characterization and data base

Energy Technology Data Exchange (ETDEWEB)

McArthur, W.C.; Kniazewycz, B.G.

1980-07-01

This report outlines the sources, quantities, characteristics and treatment of transuranic wastes in the United States. This document serves as part of the data base necessary to complete preparation and initiate implementation of transuranic wastes, waste forms, waste container and packaging standards and criteria suitable for inclusion in the present NRC waste management program. No attempt is made to evaluate or analyze the suitability of one technology over another. Indeed, by the nature of this report, there is little critical evaluation or analysis of technologies because such analysis is only appropriate when evaluating a particular application or transuranic waste streams. Due to fiscal restriction, the data base is developed from a myriad of technical sources and does not necessarily contain operating experience and the current status of all technologies. Such an effort was beyond the scope of this report.

Storage of transuranic contaminated solid wastes at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Wehmann, George

1975-01-01

The storage method for low-level transuranic wastes employed at the Idaho National Engineering Laboratory is discussed in detail. The techniques used for wastes containing greater than ten nanocuries of transuranic material per gram of waste as well as the technique for lesser concentrations of transuranic wastes are described. The safety, efficiency and adequacy of these storage methods are presented

Defense transuranic waste program strategy document

International Nuclear Information System (INIS)

1982-07-01

This document summarizes the strategy for managing transuranic (TRU) wastes generated in defense and research activities regulated by the US Department of Energy. It supercedes a document issued in July 1980. In addition to showing how current strategies of the Defense Transuranic Waste Program (DTWP) are consistent with the national objective of isolating radioactive wastes from the biosphere, this document includes information about the activities of the Transuranic Lead Organization (TLO). To explain how the DTWP strategy is implemented, this document also discusses how the TLO coordinates and integrates the six separate elements of the DTWP: (1) Waste Generation Site Activities, (2) Storage Site Activities, (3) Burial Site Activities, (4) Technology Development, (5) Transportation Development, and (6) Permanent Disposal. Storage practices for TRU wastes do not pose short-term hazards to public health and safety or to the environment. Isolation of TRU wastes in a deep-mined geologic repository is considered the most promising of the waste disposal alternatives available. This assessment is supported by the DOE Record of Decision to proceed with research and development work at the Waste Isolation Pilot Plant (WIPP) in southeastern New Mexico - a deep-mined geologic research and development project. In support of the WIPP research project and the permanent disposal of TRU waste, the DTWP strategy for the near term will concentrate on completion of procedures and the design and construction of all facilities necessary to certify newly-generated (NG) and stored TRU wastes for emplacement in the WIPP. In addition, the strategy involves evaluating alternatives for disposing of some transuranic wastes by methods which may allow for on-site disposal of these wastes and yet preserve adequate margins of safety to protect public health and the environment

Incorporation of transuranic elements in titanate nuclear waste ceramics

International Nuclear Information System (INIS)

Matzke, H.J.; Ray, I.L.F.; Theile, H.; Trisoglio, C.; Walker, C.T.; White, T.J.

1990-01-01

The incorporation of actinide elements and their rare-earth element analogues in titanate nuclear waste forms in reviewed. New partitioning data are presented for three waste forms containing Purex waste simulant in combination with either NpO 2 , PuO 2 , or Am 2 O 3 . The greater proportion of transuranics partition between perovskite and zirconolite, while some americium may enter loveringite. Autoradiography revealed clusters of plutonium atoms which have been interpreted as unreacted dioxide or sesquioxide. It is concluded that the solid-state behavior of transuranic elements in titanate waste forms is poorly understood, certainly not well enough to tailor a ceramic for the incorporation of waste from reprocessing of fast breeder reactor fuel in which transuranic species are more abundant than in Purex waste

West Valley Demonstration Project low-level and transuranic waste assay and methodology

International Nuclear Information System (INIS)

McVay, C.W.

1987-03-01

In the decontamination and decommissioning of the West Valley Nuclear Facility, waste materials are being removed and packaged in a variety of waste containers which require classification in accordance with USNRC 10 CFR 61 and DOE 5820.2 criteria. Low-Level and Transuranic waste assay systems have been developed to efficiently assay and classify the waste packages. The waste is assayed by segmented gamma scanning, passive neutron techniques, dose rate conversion, and/or radiochemical laboratory analysis. The systems are capable of handling all the waste forms currently packaged as part of the Project. The above systems produce a list of nuclides present with their concentrations and determines the classification of the waste packages based on criteria outlined in DOE Order 5820.2 and USNRC 10 CFR 61.55. 9 refs., 12 figs., 8 tabs

Final Hanford Site Transuranic (TRU) Waste Characterization Quality Assurance Project Plan

International Nuclear Information System (INIS)

GREAGER, T.M.

1999-01-01

The Transuranic Waste Characterization Quality Assurance Program Plan required each US Department of Energy (DOE) site that characterizes transuranic waste to be sent the Waste Isolation Pilot Plan that addresses applicable requirements specified in the QAPP

Contamination control aspects of attaching waste drums to the WIPP Waste Characterization Chamber

International Nuclear Information System (INIS)

Rubick, L.M.; Burke, L.L.

1998-01-01

Argonne National Laboratory West (ANL-W) is verifying the characterization and repackaging of contact-handled transuranic (CH-TRU) mixed waste in support of the Waste Isolation Pilot Program (WIPP) project located in Carlsbad, New Mexico. The WIPP Waste Characterization Chamber (WCC) was designed to allow opening of transuranic waste drums for this process. The WCC became operational in March of 1994 and has characterized approximately 240 drums of transuranic waste. The waste drums are internally contaminated with high levels of transuranic radionuclides. Attaching and detaching drums to the glove box posed serious contamination control problems. Prior to characterizing waste, several drum attachment techniques and materials were evaluated. An inexpensive HEPA filter molded into the bagging material helps with venting during detachment. The current techniques and procedures used to attach and detach transuranic waste drums to the WCC are described

Behaviour of transuranic nuclides in coastal environment

International Nuclear Information System (INIS)

Pillai, K.C.; Mathew, E.; Matkar, V.M.; Dey, N.N.; Abani, M.C.; Chhapgar, B.F.; Mullay, C.D.

1982-01-01

In view of the nuclear technological developments, the potential for contamination of marine environment with transuranic nuclides has increased. In this context it is necessary to know not only the current levels of these artificial nuclides but there is also a need to understand the physico-chemical, biological and geochemical behaviour of transuranics to evaluate their significance in the marine environment. Studies on these aspects have been carried out in the coastal environment of the west coast of India, near Bombay. The results obtained and conclusions drawn from the various investigations carried out are given in this document

Implementation plans for buried transuranic waste and stored special-case waste at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Bullock, M.G.; Rodriguez, R.R.

1987-05-01

This document presents the current implementation plans for buried transuranic waste and stored special-case waste at the Idaho National Engineering Laboratory. Information contained in this report was also included in several Department of Energy (DOE) planning documents for the Defense Transuranic Waste Program. This information can be found in the following DOE documents: Comprehensive Implementation Plan for the DOE Defense Buried TRU Waste Program; Defense Waste Management Plan for Buried Transuranic-Contaminated Waste, Transuranic-Contaminated Waste, Transuranic-Contaminated Soil, and Difficult-to-Certify Transuranic Waste; and Defense Special-Case Transuranic Waste Implementation Plan. 11 refs

Transuranic radionuclides dispersed into the environment at accident sites, a bibliography

International Nuclear Information System (INIS)

Stoker, A.C.; Noshkin, V.E.; Wong, K.M.

1994-07-01

The purpose of this project was to compile a bibliography of references containing environmental transuranic radionuclide data. The authors intent was to identify those parameters affecting transuranic radionuclide transport that may be generic and those that may be dependent on chemical form and/or environmental conditions. An understanding of the unique characteristics and similarities between source terms and environmental conditions relative to transuranic radionuclide transport and cycling will provide the ability to assess and predict the long term impact on man and the environment. An additional goal of the literature review, was to extract the ranges of environmental transuranic radionuclide data from the identified references for inclusion in a data base. Related to source term, these ranges of data can be used to calculate the dose to man from the radionuclides, and to perform uncertainty analyses on these dose assessments

Characterization and handling solutions through development and adaptation of available technologies

International Nuclear Information System (INIS)

Michel, W.S.; Frazee, C.

1998-01-01

The Department of Energy (DOE) faces unique challenges in characterizing and handling its mixed wastes. Mixed waste is low-level or transuranic (TRU) contaminated wastes containing Resource Conservation and Recovery Act (RCRA) hazardous materials. Characterization and material handling technologies will be required to solve pretreatment and disposal needs, and to meet transportation requirements. The Mixed Waste Focus Area (MWFA) will fund the development and demonstration of characterization and material handling technologies to ensure the availability to support the DOE mixed waste needs. The MWFA will be evaluating commercially available and laboratory developed technologies for applicability in meeting these needs. Improved systems will be developed, on the commercial or laboratory side, as needed to address unmet needs. Studies/demonstrations are taking place this year to evaluate the capabilities of existing systems and identify technology gaps. Calls for proposals will be made to both industry and laboratory to identify work to address those gaps. Prioritization of applicable proposals will take place and activities funded appropriately to address characterization and material handling needs

Transuranic waste form characterization and data base. Executive summary

International Nuclear Information System (INIS)

1980-01-01

The Transuranic Waste Form Characterization and Data Base (Volume 1) provides a wide range of information from which a comprehensive data base can be established and from which standards and criteria can be developed for the present NRC waste management program. Supplementary information on each of the areas discussed in Volume 1 is presented in Appendices A through K (Volumes 2 and 3). The structure of the study (Volume 1) is outlined and appendices of Volumes 2 and 3 correlate with each main section of the report. The Executive Summary reviews the sources, quantities, characteristics and treatment of transuranic wastes in the United States. Due to the variety of potential treatment processes for transuranic wastes, the end products for long-term storage may have corresponding variations in quantities and characteristics

Final Hanford Site Transuranic (TRU) Waste Characterization Qualit Assurance Project Plan

International Nuclear Information System (INIS)

GREAGER, T.M.

1999-01-01

The Transuranic Waste Characterization Quality Assurance Program Plan required each U.S. Department of Energy (DOE) site that characterizes transuranic waste to be sent the Waste Isolation Pilot Plan that addresses applicable requirements specified in the quality assurance project plan (QAPP)

Ultratrace analysis of transuranic actinides by laser-induced fluorescence

Science.gov (United States)

Miller, S.M.

1983-10-31

Ultratrace quantities of transuranic actinides are detected indirectly by their effect on the fluorescent emissions of a preselected fluorescent species. Transuranic actinides in a sample are coprecipitated with a host lattice material containing at least one preselected fluorescent species. The actinide either quenches or enhances the laser-induced fluorescence of the preselected fluorescent species. The degree of enhancement or quenching is quantitatively related to the concentration of actinide in the sample.

The Transuranic Waste Program's integration and planning activities and the contributions of the TRU partnership

International Nuclear Information System (INIS)

Harms, T.C.; O'Neal, W.; Petersen, C.A.; McDonald, C.E.

1994-02-01

The Technical Support Division, EM-351 manages the integration and planning activities of the Transuranic Waste Program. The Transuranic Waste Program manager provides transuranic waste policy, guidance, and issue resolution to Headquarters and the Operations Offices. In addition, the program manager is responsible for developing and implementing an integrated, long-range waste management plan for the transuranic waste system. A steering committee, a core group of support contractors, and numerous interface working groups support the efforts of the program manager. This paper provides an overview of the US Department of Energy's transuranic waste integration activities and a long-range planning process that includes internal and external stakeholder participation. It discusses the contributions and benefits provided by the Transuranic Partnership, most significantly, the integration activities and the body of data collected and assembled by the Partnership

Expert system for transuranic waste assay

Energy Technology Data Exchange (ETDEWEB)

Zoolalian, M.L.; Gibbs, A.; Kuhns, J.D.

1989-01-01

Transuranic wastes are generated at the Savannah River Site (SRS) as a result of routine production of nuclear materials. These wastes contain Pu-238 and Pu-239 and are placed into lined 55-gallon waste drums. The drums are placed on monitored storage pads pending shipment to the Waste Isolation Pilot Plant in New Mexico. A passive-active neutron (PAN) assay system is used to determine the mass of the radioactive material within the waste drums. Assay results are used to classify the wastes as either low-level or transuranic (TRU). During assays, the PAN assay system communicates with an IBM-AT computer. A Fortran computer program, called NEUT, controls and performs all data analyses. Unassisted, the NEUT program cannot adequately interpret assay results. To eliminate this limitation, an expert system shell was used to write a new algorithm, called the Transuranic Expert System (TRUX), to drive the NEUT program and add decision making capabilities for analysis of the assay results. The TRUX knowledge base was formulated by consulting with human experts in the field of neutron assay, by direct experimentation on the PAN assay system, and by observing operations on a daily basis. TRUX, with its improved ability to interpret assay results, has eliminated the need for close supervision by a human expert, allowing skilled technicians to operate the PAN assay system. 4 refs., 1 fig., 4 tabs.

Expert system for transuranic waste assay

International Nuclear Information System (INIS)

Zoolalian, M.L.; Gibbs, A.; Kuhns, J.D.

1989-01-01

Transuranic wastes are generated at the Savannah River Site (SRS) as a result of routine production of nuclear materials. These wastes contain Pu-238 and Pu-239 and are placed into lined 55-gallon waste drums. The drums are placed on monitored storage pads pending shipment to the Waste Isolation Pilot Plant in New Mexico. A passive-active neutron (PAN) assay system is used to determine the mass of the radioactive material within the waste drums. Assay results are used to classify the wastes as either low-level or transuranic (TRU). During assays, the PAN assay system communicates with an IBM-AT computer. A Fortran computer program, called NEUT, controls and performs all data analyses. Unassisted, the NEUT program cannot adequately interpret assay results. To eliminate this limitation, an expert system shell was used to write a new algorithm, called the Transuranic Expert System (TRUX), to drive the NEUT program and add decision making capabilities for analysis of the assay results. The TRUX knowledge base was formulated by consulting with human experts in the field of neutron assay, by direct experimentation on the PAN assay system, and by observing operations on a daily basis. TRUX, with its improved ability to interpret assay results, has eliminated the need for close supervision by a human expert, allowing skilled technicians to operate the PAN assay system. 4 refs., 1 fig., 4 tabs

Radiological Characterization Methodology for INEEL-Stored Remote-Handled Transuranic (RH TRU) Waste from Argonne National Laboratory-East

International Nuclear Information System (INIS)

Kuan, P.; Bhatt, R.N.

2003-01-01

An Acceptable Knowledge (AK)-based radiological characterization methodology is being developed for RH TRU waste generated from ANL-E hot cell operations performed on fuel elements irradiated in the EBR-II reactor. The methodology relies on AK for composition of the fresh fuel elements, their irradiation history, and the waste generation and collection processes. Radiological characterization of the waste involves the estimates of the quantities of significant fission products and transuranic isotopes in the waste. Methods based on reactor and physics principles are used to achieve these estimates. Because of the availability of AK and the robustness of the calculation methods, the AK-based characterization methodology offers a superior alternative to traditional waste assay techniques. Using the methodology, it is shown that the radiological parameters of a test batch of ANL-E waste is well within the proposed WIPP Waste Acceptance Criteria limits

Intercomparison of transuranics in sediments

International Nuclear Information System (INIS)

Nilsson, K.

1981-01-01

This paper summarizes the results of a recent intercomparison of transuranic analyses in Nordic sediments undertaken by five laboratories. Five different samplers were tested to determine their consistency and utility. Plutonium and americium were determined in all the samples and the analysis of variance is discussed. (author)

Relationship of microbial processes to the fate of transuranic elements in soil

International Nuclear Information System (INIS)

Wildung, R.E.; Drucker, H.

1975-09-01

Any assessment of the long-term behavior of the transuranics in the terrestrial environment must be based on determination of the factors influencing solubility in soil. The influence of soil properties and abiotic and biotic processes on the long-term solubility of the transuranics entering soils is reviewed in detail. Principal emphasis is directed toward the role of soil microorganisms. Emphasis is given to plutonium, but, where possible, the available information is used to discuss long-term behavior of other transuranics

Root uptake of transuranic elements

International Nuclear Information System (INIS)

Schulz, R.K.

1977-01-01

The uptake of elements by plant roots is one of the important pathways of entry of many elements into the food chain of man. Data are cited showing plutonium concentration ratios, plant/soil, ranging from 10 -10 to 10 -3 . Concentration ratios for americium range from 10 -7 to 10 +1 . Limited experiments with curium and neptunium indicate that root uptake of curium is similar to that of americium and that plant uptake of neptunium is substantially larger than that of curium and americium. The extreme ranges of concentration ratios cited for plutonium and americium are due to a number of causes. Experimental conditions such as very intensive cropping will lead to abnormally high concentration ratios. In some experiments, addition of chelating agents markedly increased plant root uptake of transuranic elements. Particle size and composition of the source material influenced uptake of the transuranics by plants. Translocation within the plant, and soil factors such as pH and organic matter content, all affect concentration ratios

C-tank transfers: Transuranic sludge removal from the C-1, C-2, and W-23 waste storage tanks at Oak Ridge National Laboratory, Oak Ridge, Tennessee

International Nuclear Information System (INIS)

Dahl, T.L.; Lay, A.C.; Taylor, S.A.; Moore, J.W.

1999-01-01

Two fluidic pulse jet mixing systems were used to successfully mobilize remote-handled transuranic sludge for retrieval from three 50,000-gal horizontal waste storage tanks at Oak Ridge National Laboratory (ORNL). The results of this operation indicate that the pulse jet system should be considered for mixing and bulk retrieval of sludges in other vertical and horizontal waste tanks at ORNL and at other U.S. Department of Energy sites

Fusion option to dispose of spent nuclear fuel and transuranic elements

International Nuclear Information System (INIS)

Gohar, Y.

2000-01-01

The fusion option is examined to solve the disposition problems of the spent nuclear fuel and the transuranic elements. The analysis of this report shows that the top rated solution, the elimination of the transuranic elements and the long-lived fission products, can be achieved in a fusion reactor. A 167 MW of fusion power from a D-T plasma for sixty years with an availability factor of 0.75 can transmute all the transuranic elements and the long-lived fission products of the 70,000 tons of the US inventory of spent nuclear fuel generated up to the year 2015. The operating time can be reduced to thirty years with use of 334 MW of fusion power, a system study is needed to define the optimum time. In addition, the fusion solution eliminates the need for a geological repository site, which is a major advantage. Meanwhile, such utilization of the fusion power will provide an excellent opportunity to develop fusion energy for the future. Fusion blankets with a liquid carrier for the transuranic elements can achieve a transmutation rate for the transuranic elements up to 80 kg/MW.y of fusion power with k eff of 0.98. In addition, the liquid blankets have several advantages relative to the other blanket options. The energy from this transmutation is utilized to produce revenue for the system. Molten salt (Flibe) and lithium-lead eutectic are identified as the most promising liquids for this application, both materials are under development for future fusion blanket concepts. The Flibe molten salt with transuranic elements was developed and used successfully as nuclear fuel for the molten salt breeder reactor in the 1960's

National Transuranic Program Charter

International Nuclear Information System (INIS)

1994-10-01

The National Transuranic Program Plan and Charter describes the functional elements of the National TRU Program, organizational relationships, programmatic responsibilities, division of work scope among the various DOE organizations that comprise the program, and program baselines against which overall progress will be measured. The charter defines the authorities and responsibilities of various organizations involved in the management of TRU waste throughout the DOE complex

Measurements of transuranic elements in the Mediterranean

International Nuclear Information System (INIS)

Ballestra, S.; Holm, E.; Fukai, R.

1976-01-01

In order to supplement the baseline data on the distribution of transuranic elements in the Mediterranean, which have already been reported, further measurements were carried out on sea water samples collected during 1974-75 cruises. In 1974 profile collections were conducted at a station approximately 50 km south of Monaco in addition to surface sampling at a few stations, while surface waters were taken from several stations covering wider regions of the western Mediterranean during the 1975 cruises. The measurement of 238 Pu as well as 241 Am were for the first time successful on the 1975 samples. These data are considered valuable as the basis for understanding transuranic biogeochemistry in the Mediterranean environment

Analyses for some transuranic and natural radionuclides in the environmental samples

International Nuclear Information System (INIS)

Harley, J.H.

1978-01-01

There is considerable present and expected future interest in the contamination of the environment with transuranic elements, particularly plutonium and americium. In addition, the alpha-emitting natural radionuclides are the usual standard of comparison for such transuranic element contamination. The present paper reviews the quality of data available for evaluating the distribution of transuranic elements and some natural radioactive elements in the environment. The overall quality cannot be documented for most programs and the data that are available indicate that the quality is poor. The fact that a few programs maintain high quality analyses indicates that the cause is poor analytical work rather than poor methods of analysis. (author)

Handling Pyrophoric Reagents

Energy Technology Data Exchange (ETDEWEB)

Alnajjar, Mikhail S.; Haynie, Todd O.

2009-08-14

Pyrophoric reagents are extremely hazardous. Special handling techniques are required to prevent contact with air and the resulting fire. This document provides several methods for working with pyrophoric reagents outside of an inert atmosphere.

Transuranic Solid Waste Management Programs. Progress report, July--December 1974

International Nuclear Information System (INIS)

1975-10-01

Progress is reported for three transuranic solid waste management programs funded at the Los Alamos Scientific Laboratory by the Energy Research and Development Administration Division of Waste Management and Transportation. Under the Transuranic Waste Research and Development Program, a completed evaluation of stainless steel drums showed that although the material has superior corrosion-resistant properties, its higher cost makes a thorough investigation of other container systems mandatory. A program to investigate more economical, nonmetallic containers is proposed. Preliminary fire tests in mild steel drums have been completed with fire propagation not appearing to be a problem unless container integrity is lost. Investigation of the corrosion of mild steel drums and the evaluation of potential corrosion inhibitors, in a variety of humid environments, continues. Experimental results of both laboratory and field investigations on radiolysis of transuranic elements in hydrogenous waste are discussed. Progress in the development of instrumentation for monitoring and segregating low-level wastes is described. New plans and developments for the Transuranic-Contaminated Solid Waste Treatment Development Facility are presented. The current focus is on a comparison of all alternative waste reduction systems toward a relative Figure of Merit with universal application. Drawings, flowsheets, and building layouts are included, and the proposed incinerator device is detailed. The release mechanisms, inter- and intraregional transport mechanisms, and exhumation studies relevant to the Evaluation of Transuranic-Contaminated Radioactive Waste Disposal Areas Program are defined and analyzed. A detailed description is given of the formulation of the computer simulation scheme for the intraregional biological transport model

Development of the remote-handled transuranic waste radioassay data quality objectives. An evaluation of RH-TRU waste inventories, characteristics, radioassay methods and capabilities

Energy Technology Data Exchange (ETDEWEB)

Meeks, A.M.; Chapman, J.A.

1997-09-01

The Waste Isolation Pilot Plant will accept remote-handled transuranic waste as early as October of 2001. Several tasks must be accomplished to meet this schedule, one of which is the development of Data Quality Objectives (DQOs) and corresponding Quality Assurance Objectives (QAOs) for the assay of radioisotopes in RH-TRU waste. Oak Ridge National Laboratory (ORNL) was assigned the task of providing to the DOE QAO, information necessary to aide in the development of DQOs for the radioassay of RH-TRU waste. Consistent with the DQO process, information needed and presented in this report includes: identification of RH-TRU generator site radionuclide data that may have potential significance to the performance of the WIPP repository or transportation requirements; evaluation of existing methods to measure the identified isotopic and quantitative radionuclide data; evaluation of existing data as a function of site waste streams using documented site information on fuel burnup, radioisotope processing and reprocessing, special research and development activities, measurement collection efforts, and acceptable knowledge; and the current status of technologies and capabilities at site facilities for the identification and assay of radionuclides in RH-TRU waste streams. This report is intended to provide guidance in developing the RH-TRU waste radioassay DQOs, first by establishing a baseline from which to work, second, by identifying needs to fill in the gaps between what is known and achievable today and that which will be required before DQOs can be formulated, and third, by recommending measures that should be taken to assure that the DQOs in fact balance risk and cost with an achievable degree of certainty.

Development of the remote-handled transuranic waste radioassay data quality objectives. An evaluation of RH-TRU waste inventories, characteristics, radioassay methods and capabilities

International Nuclear Information System (INIS)

Meeks, A.M.; Chapman, J.A.

1997-09-01

The Waste Isolation Pilot Plant will accept remote-handled transuranic waste as early as October of 2001. Several tasks must be accomplished to meet this schedule, one of which is the development of Data Quality Objectives (DQOs) and corresponding Quality Assurance Objectives (QAOs) for the assay of radioisotopes in RH-TRU waste. Oak Ridge National Laboratory (ORNL) was assigned the task of providing to the DOE QAO, information necessary to aide in the development of DQOs for the radioassay of RH-TRU waste. Consistent with the DQO process, information needed and presented in this report includes: identification of RH-TRU generator site radionuclide data that may have potential significance to the performance of the WIPP repository or transportation requirements; evaluation of existing methods to measure the identified isotopic and quantitative radionuclide data; evaluation of existing data as a function of site waste streams using documented site information on fuel burnup, radioisotope processing and reprocessing, special research and development activities, measurement collection efforts, and acceptable knowledge; and the current status of technologies and capabilities at site facilities for the identification and assay of radionuclides in RH-TRU waste streams. This report is intended to provide guidance in developing the RH-TRU waste radioassay DQOs, first by establishing a baseline from which to work, second, by identifying needs to fill in the gaps between what is known and achievable today and that which will be required before DQOs can be formulated, and third, by recommending measures that should be taken to assure that the DQOs in fact balance risk and cost with an achievable degree of certainty

Management of transuranics using Integral Fast Reactor fuel cycle

International Nuclear Information System (INIS)

Wade, D.C.

1994-01-01

The 50 years of activities following the discovery of self-sustained fission chains have given rise to a buildup of roughly 900 tonnes of manmade transuranics. The formation of the transuranics is initiated by the parasitic neutron capture on the abundant isotope (U 238 ) of uranium ore to produce Pu 239 and the minor actinides are formed via the unavoidable parasitic neutron capture on the transuranic isotopes themselves. of the total, 260 tonnes of Pu 239 were generated for use in weapons while the remainder were generated as a byproduct of electrical power produced worldwide by the commercial thermal nuclear power industry. What to be done with these actinides? The options for disposition include interminable storage, burial, or recycle for use. The pros and cons of each option are being vigorously debated regarding the impact upon the issues of human and ecological risk both current and future; weapon proliferation potential both current and future; and total life cycle benefits and costs. (authors). 1 fig

Transportation considerations related to waste forms and canisters for Defense TRU wastes

International Nuclear Information System (INIS)

Schneider, K.J.; Andrews, W.B.; Schreiber, A.M.; Rosenthal, L.J.; Odle, C.J.

1981-09-01

This report identifies and discusses the considerations imposed by transportation on waste forms and canisters for contact-handled, solid transuranic wastes from the US Department of Energy (DOE) activities. The report reviews (1) the existing raw waste forms and potential immobilized waste forms, (2) the existing and potential future DOE waste canisters and shipping containers, (3) regulations and regulatory trends for transporting commercial transuranic wastes on the ISA, (4) truck and rail carrier requirements and preferences for transporting the wastes, and (5) current and proposed Type B external packagings for transporting wastes

Use of analog elements to predict the equilibrium and behavior of transuranic elements in the environment

International Nuclear Information System (INIS)

Weimer, W.C.; Laul, J.C.; Kutt, J.C.

1978-01-01

Several naturally-occurring elements with chemical properties similar to those of selected transuranic elements have been chosen and are being examined as potential predictors of transuranic geochemical behaviors. This approach may allow the estimation of the long-term behaviors of transuranic elements in the environment by analyses of the steady-state behaviors of their analog elements. The elements receiving principal attention are the transuranics Am and Cm and their proposed lanthanide element analog Nd

Certification Plan, Radioactive Mixed Waste Hazardous Waste Handling Facility

International Nuclear Information System (INIS)

Albert, R.

1992-01-01

The purpose of this plan is to describe the organization and methodology for the certification of radioactive mixed waste (RMW) handled in the Hazardous Waste Handling Facility at Lawrence Berkeley Laboratory (LBL). RMW is low-level radioactive waste (LLW) or transuranic (TRU) waste that is co-contaminated with dangerous waste as defined in the Westinghouse Hanford Company (WHC) Solid Waste Acceptance Criteria (WAC) and the Washington State Dangerous Waste Regulations, 173-303-040 (18). This waste is to be transferred to the Hanford Site Central Waste Complex and Burial Grounds in Hanford, Washington. This plan incorporates the applicable elements of waste reduction, which include both up-front minimization and end-product treatment to reduce the volume and toxicity of the waste; segregation of the waste as it applies to certification; an executive summary of the Waste Management Quality Assurance Implementing Management Plan (QAIMP) for the HWHF (Section 4); and a list of the current and planned implementing procedures used in waste certification

Developing an institutional strategy for transporting defense transuranic waste materials

International Nuclear Information System (INIS)

Guerrero, J.V.; Kresny, H.S.

1986-01-01

In late 1988, the US Department of Energy (DOE) expects to begin emplacing transuranic waste materials in the Waste Isolation Pilot Plant (WIPP), an R and D facility to demonstrate the safe disposal of radioactive wastes resulting from defense program activities. Transuranic wastes are production-related materials, e.g., clothes, rags, tools, and similar items. These materials are contaminated with alpha-emitting transuranium radionuclides with half-lives of > 20 yr and concentrations > 100 nCi/g. Much of the institutional groundwork has been done with local communities and the State of New Mexico on the siting and construction of the facility. A key to the success of the emplacement demonstration, however, will be a qualified transportation system together with institutional acceptance of the proposed shipments. The DOE's Defense Transuranic Waste Program, and its contractors, has lead responsibility for achieving this goal. The Joint Integration Office (JIO) of the DOE, located in Albuquerque, New Mexico, is taking the lead in implementing an integrated strategy for assessing nationwide institutional concerns over transportation of defense transuranic wastes and in developing ways to resolve or mitigate these concerns. Parallel prototype programs are under way to introduce both the new packaging systems and the institutional strategy to interested publics and organizations

Historical review of transuranic analytical methodology

International Nuclear Information System (INIS)

Wessman, R.A.; Leventhal, L.

1977-01-01

The methods used for the analysis of the transuranic elements neptunium, plutonium, americium, and curium are reviewed. Particular attention is given to those procedures suitable for low-level environmental and biological assessment. The preparation of such samples, derived from a variety of sources and incorporated in different masses and volumes of soils, water, vegetation, and biological matrices, is described. A comprehensive discussion of matrix dissolution and equilibration techniques indicates that complete dissolution employing tracer techniques is to be preferred. Leaching of large soil samples is satisfactory for worldwide fallout. Individual and sequential separation and purification procedures, including precipitation, extraction, and ion exchange methods, are described. Sample preparation techniques for radiometric assay, such as stippling, evaporation, and plating, are reviewed. For both tracer and nuclide assay, electroplating provides the thin samples suitable for alpha pulse height analysis. Past and current counting methods for the transuranic alpha, beta, and gamma emitters are reviewed

Physical and Liquid Chemical Simulant Formulations for Transuranic Waste in Hanford Single-Shell Tanks

International Nuclear Information System (INIS)

Rassat, Scot D.; Bagaasen, Larry M.; Mahoney, Lenna A.; Russell, Renee L.; Caldwell, Dustin D.; Mendoza, Donaldo P.

2003-01-01

CH2M HILL Hanford Group, Inc. (CH2M HILL) is in the process of identifying and developing supplemental process technologies to accelerate the tank waste cleanup mission. A range of technologies is being evaluated to allow disposal of Hanford waste types, including transuranic (TRU) process wastes. Ten Hanford single-shell tanks (SSTs) have been identified whose contents may meet the criteria for designation as TRU waste: the B-200 series (241-B-201, -B-202, -B 203, and B 204), the T-200 series (241-T-201, T 202, -T-203, and -T-204), and Tanks 241-T-110 and -T-111. CH2M HILL has requested vendor proposals to develop a system to transfer and package the contact-handled TRU (CH-TRU) waste retrieved from the SSTs for subsequent disposal at the Waste Isolation Pilot Plant (WIPP). Current plans call for a modified ''dry'' retrieval process in which a liquid stream is used to help mobilize the waste for retrieval and transfer through lines and vessels. This retrieval approach requires that a significant portion of the liquid be removed from the mobilized waste sludge in a ''dewatering'' process such as centrifugation prior to transferring to waste packages in a form suitable for acceptance at WIPP. In support of CH2M HILL's effort to procure a TRU waste handling and packaging process, Pacific Northwest National Laboratory (PNNL) developed waste simulant formulations to be used in evaluating the vendor's system. For the SST CH-TRU wastes, the suite of simulants includes (1) nonradioactive chemical simulants of the liquid fraction of the waste, (2) physical simulants that reproduce the important dewatering properties of the waste, and (3) physical simulants that can be used to mimic important rheological properties of the waste at different points in the TRU waste handling and packaging process. To validate the simulant formulations, their measured properties were compared with the limited data for actual TRU waste samples. PNNL developed the final simulant formulations

Dismantling of transuranic contaminated facilities

International Nuclear Information System (INIS)

Roux, P.

1985-01-01

The dismantling of transuranic contaminated facilities raises specific problems. A large part of these problems relates to the management of the waste resulting from dismantling. From the experience gained in the different centers CEA and COGEMA it appears that there are industrial solutions in the group CEA and that an engineering company such as SGN can export them [fr

Transuranic behaviour in marine environment

International Nuclear Information System (INIS)

Bowen, V.T.

1982-01-01

This document summarizes the following specific studies concerning the transuranic behaviour in marine environment: 1. Radionuclides in deep sea amphipods; 2. Actinides, 55 Fe and 137 Cs in N. pacific water columns; 3. Vertical profile of artificial radionuclide concentrations in the central Arctic Ocean; 4. Bioturbation and the distributions of fallout radionuclides in Pacific Ocean sediments

LMR design concepts for transuranic management in low sodium void worth cores

International Nuclear Information System (INIS)

Hill, R.N.

1991-01-01

The fuel cycle processing techniques and hard neuron spectrum of the Integral Fast Reactor (IFR) metal fuel cycle have favorable characteristics for the management of transuranics; and the wide range of breeding characteristics available in metal fuelled cores provides for flexibility in transuranic management strategy. Previous studies indicate that most design options which decrease the breeding ratio also show a decrease in sodium void worth; therefore, low void worths are achievable in transuranic burning (low breeding ratio) core designs. This paper describes numerous trade studies assessing various design options for a low void worth transuranic burner core. A flat annular core design appears to be a promising concept; the high leakage geometry yields a low breeding ratio and small sodium void worth. To allow flexibility in breeding characteristics, alternate design options which achieve fissile self-sufficiency are also evaluated. A self-sufficient core design which is interchangeable with the burner core and maintains a low sodium void worth is developed. 13 refs., 1 fig., 4 tabs

LMR design concepts for transuranic management in low sodium void worth cores

International Nuclear Information System (INIS)

Hill, R.N.

1991-01-01

The fuel cycle processing techniques and hard neutron spectrum of the integral Fast Reactor (IFR) metal fuel cycle have favorable characteristics for the management of transuranics; and the wide range of breeding characteristics available in metal fuelled cores provides for flexibility in transuranic management strategy. Previous studies indicate that most design options which decrease the breeding ratio also allow a decrease in sodium void worth; therefore, low void worths are achievable in transuranic burning (low breeding ratio) core designs. This paper describes numerous trade studies assessing various design options for a low void worth transuranic burner core. A flat annular core design appears to be a promising concept; the high leakage geometry yields a low breeding ratio and small sodium void worth. To allow flexibility in breeding characteristics, alternate design options which achieve fissile self-sufficiency are also evaluated. A self-sufficient core design which is interchangeable with the burner core and maintains a low sodium void worth is developed. (author)

EVALUATION OF ALTERNATIVE STRONIUM AND TRANSURANIC SEPARATION PROCESSES

Energy Technology Data Exchange (ETDEWEB)

SMALLEY CS

2011-04-25

In order to meet contract requirements on the concentrations of strontium-90 and transuranic isotopes in the immobilized low-activity waste, strontium-90 and transuranics must be removed from the supernate of tanks 241-AN-102 and 241-AN-107. The process currently proposed for this application is an in-tank precipitation process using strontium nitrate and sodium permanganate. Development work on the process has not proceeded since 2005. The purpose of the evaluation is to identify whether any promising alternative processes have been developed since this issue was last examined, evaluate the alternatives and the baseline process, and recommend which process should be carried forward.

Pyrometallurgical partitioning of uranium and transuranic elements from rare earth elements by electrorefining and reductive extraction

International Nuclear Information System (INIS)

Uozumi, Koichi; Kinoshita, Kensuke; Inoue, Tadashi; Storvick, T.S.; Krueger, C.L.; Nabelek, C.R.

2001-01-01

High-level liquid waste generated from PUREX reprocessing contains a small amount of transuranic elements, such as Np, Pu, Am, and Cm, with long-lived radioactivities. A pyrometallurgical partitioning process is being developed to recover transuranic elements from such waste. Small amounts of U contained in the high-level liquid waste are also recovered in the process. A key issue for developing the process is effective separation of U and the transuranic elements from the rare-earth elements, because the two elemental groups are chemically analogous. A series of process tests were carried out in the present study to demonstrate that a combination of electrorefining and reductive extraction is useful for separating U and transuranic elements from the rare-earth elements. The results indicate that 99% of U and each transuranic elements is recovered by the combination process as a product, and that the quantity of rare-earth elements contained in the product is smaller than the transuranic elements by weight. The overall mass balance of U and transuranic elements in the system ranged within the experimental errors assigned to sampling and analysis. (author)

Neutron measurement method for the detection of transuranic elements in the nuclear fuel cycle; Neutronenmessverfahren fuer den Nachweis von Transuranen im Kernbrennstoff-Kreislauf

Energy Technology Data Exchange (ETDEWEB)

Sokcic-Kostic, Marina; Schultheis, Roland [NUKEM Technologies GmbH, Alzenau (Germany)

2014-07-01

By handling and storing burned-down fuel elements operators are obliged to measure the existing nuclear fuel content. Due to high penetration of matter and its origin from decay or spontaneous fission of transuranic elements neutron verification methods are suited best for the proof of fission material as long as it has been burned-down beforehand. A highly improved measuring quality can be achieved by comparing measurement results with the results of computer-aided simulations such as e.g. burn-up programs or MCNP- calculations. (orig.)

US Department of Energy acceptance of commercial transuranic waste

International Nuclear Information System (INIS)

Taboas, A.L.; Bennett, W.S.; Brown, C.M.

1980-02-01

Contaminated transuranic wastes generated as a result of non-defense activities have been disposed of by shallow land burial at a commercially operated (NECO) facility located on the Hanford federal reservation, which is licensed by the State of Washington and by the NRC. About 15,000 ft 3 of commercial TRU waste have been generated each year, but generation for the next three years could triple due to decontamination and decommissioning scheduled to start in 1980. Disposal at other commercial burial sites has been precluded due to sites closing or prohibitions on acceptance of transuranic wastes. The State of Washington recently modified the NECO-Hanford operating license, effective February 29, 1980, to provide that radioactive wastes contaminated with transuranics in excess of 10 nCi/g will not be accepted for disposal. Consistent with the state policy, the NRC amended the NECO special nuclear material license so that Pu in excess of 10n Ci/g cannot be accepted after February 29, 1980. As a result, NRC requested DOE to examine the feasibility of accepting these wastes at a DOE operated site. TRU wastes accepted by the DOE would be placed in retrievable storage in accordance with DOE policy which requires retrievable storage of transuranic wastes pending final disposition in a geologic repository. DOE transuranic wastes are stored at six major DOE sites: INEL, Hanford, LASL, NTS, ORNL, and SRP. A specific site for receiving commercial TRU waste has not yet been selected. Shipments to DOE-Hanford would cause the least disruption to past practices. Commercial TRU wastes would be subject to waste form and packaging criteria established by the DOE. The waste generators would be expected to incur all applicable costs for DOE to take ownership of the waste, and provide storage, processing, and repository disposal. The 1980 charge to generators for DOE acceptance of commercial TRU waste is $147 per cubic foot

Characterization of transuranic elements at environmental levels

International Nuclear Information System (INIS)

Edgington, D.N.

1981-01-01

This paper summarizes current understanding of transuranic speciation in natural waters. Several predictive models describing the behaviour of these elements in both marine and fresh-water systems illustrate the importance of this information. (author)

Containment of transuranic contamination at the early waste retrieval project

International Nuclear Information System (INIS)

Harness, J.L.; McKinney, J.D.

1977-01-01

On July 26, 1976, while retrieving buried transuranic waste under the Early Waste Retrieval Program, a corroded 55-gallon 17H drum was retrieved. When uprighted, several liters of liquid escaped from the drum. This liquid was contaminated with transuranics, principally Pu-239, Am-241, and some Pu-238. As a result of the spread of this contamination in the Operating Area Confinement, six working days were required to decontaminate the area. At no time did the contamination escape the interior of the Operating Area Confinement building, and no contamination to personnel resulted from this occurrence, nor was a hazard presented to the general public. The facility was designed and constructed to contain the transuranic contamination resulting from such an occurrence. Proper prior planning and personnel training prevented the contamination occurrence from becoming a major event. This report details the occurrence, the recovery, and the information obtained from this event

Characterization of transuranic solid wastes from a plutonium processing facility

International Nuclear Information System (INIS)

Mulkin, R.

1975-06-01

Transuranic-contaminated wastes generated in the processing areas of the Plutonium Chemistry and Metallurgy Group at the Los Alamos Scientific Laboratory (LASL) were studied in detail to identify their chemical and physical composition. Nondestructive Assay (NDA) equipment was developed to measure transuranic activity at the 10-nCi/g level in low-density residues typically found in room-generated waste. This information will supply the Waste Management Program with a more positive means of identifying concerns in waste storage and the challenge of optimizing the system of waste form, packaging, and environment of the storage area for 20-yr retrievable waste. A positive method of measuring transuranic activity in waste at the 10-nCi/g level will eliminate the need for administrative control in a sensitive area, and will provide the economic advantage of minimizing the volume of waste stored as retrievable waste. (U.S.)

Transuranic Storage Area (TSA)-2 container storage unit RCRA closure plan

International Nuclear Information System (INIS)

Lodman, D.W.; Spry, M.J.; Nolte, E.P.; Barry, G.A.

1992-11-01

This document describes the proposed plans for closure of the Transuranic Storage Area (TSA)-2 container storage unit at the Idaho National Engineering Laboratory in accordance with the Resource Conservation and Recovery Act closure requirements. The location, size, capacity, history, and current status of the unit are described. Future plans for the unit include incorporating the earthen-covered portion of the TSA-2 pad into a TSA retrieval enclosure along with the TSA-1 and TSAR pads, and closure of the portion of the TSA-2 pad under the Air Support Weather Shield (ASWS-2). This plan addresses closure of the ASWS-2 by decontaminating structures and equipment that may have contacted the waste. Sufficient sampling and documentation of all closure activities will be performed to demonstrate clean closure. A tentative schedule is provided in the form of a milestone chart

Neutron measurement method for the detection of transuranic elements in the nuclear fuel cycle; Neutronenmessverfahren fuer den Nachweis von Transuranen im Kernbrennstoff-Kreislauf

Energy Technology Data Exchange (ETDEWEB)

Sokcic-Kostic, Marina; Schultheis, Roland [NUKEM Technologies GmbH, Alzenau (Germany)

2014-04-15

By handling and storing burned-down fuel elements it is duty to measure the existing nuclear fuel content. For the criticality analysis of the interim storage, for instance, it is imperative to know the nuclear fuel inventory in order to give a detailed description on the safety of storage to the supervisory authority. Among other things, it is necessary to consider that the possibility of mixing up stored fuel elements in the fuel pool was not able to be excluded. Due to high penetration of matter and its origin from decay or spontaneous fission of transuranic elements neutron verification methods are suited best for the proof of fission material as long as it has been burned-down beforehand. If fission chambers are additionally used as detectors, measurements can be even carried out in environments with high gamma levels. A highly improved measuring quality can be achieved, by comparing measurement results with the results of computer-aided simulations such as e.g. burn-up programs or MCNP- calculations. Hereby the impact on the measurement result by special marginal conditions of the measuring environment (e.g. addition of boric acid into the water of the fuel pool) can be estimated and thus revised. It is shown, that the passive neutron measurement is much easier to manage as an active measurement. As restriction it is to be considered, that measurements refer essentially to transuranic elements. Uranium such as U-235, however, is difficult to detect. For fuel elements applies, that the creation of transuranic elements is directly linked to the burn-up of U-235. Hence direct conclusions to the burn-up of U-235 can be drawn, by measuring transuranic content. (orig.)

Transuranic radionuclides in the environment surrounding radioactive waste diposal sites, a bibliography

International Nuclear Information System (INIS)

Stoker, A.C.; Noshkin, V.E.; Wong, K.M.; Brunk, J.L.; Conrado, C.L.; Jones, H.E.; Kehl, S.; Stuart, M.L.; Wasley, L.M.; Bradsher, R.V.

1994-08-01

The purpose of this project was to compile a bibliography of references containing environmental transuranic radionuclide data. Our intent was to identify those parameters affecting transuranic radionuclide transport that may be generic and those that may be dependent on chemical form and/or environmental conditions (i.e. site specific). An understanding of the unique characteristics and similarities between source terms and environmental conditions relative to transuranic radionuclide transport and cycling will provide the ability to assess and predict the long term impact on man and the environment. An additional goal of our literature review, was to extract the ranges of environmental transuranic radionuclide data from the identified references for inclusion in a data base. Related to source term, these ranges of data can be used to calculate the dose to man from the radionuclides, and to perform uncertainty analyses on these dose assessments. In an attempt to gather relevant information about the transuranic radionuclides in a variety of environments, we conducted an extensive literature search. In our literature search we identified over 5700 potential written sources of information for review. In addition, we have identified many references which were not found through the literature searches, but which were known to contain useful data. A total of approximately 2600 documents were determined to contain information which would be useful for an in depth study of radionuclides in different environments. The journal articles, books, reports and other documents were reviewed to obtain the source term of the radionuclides studied. Most references containing laboratory study data were not included in our databases. Although these may contain valuable data, we were trying to compile references with information on the behavior of the transuranics in the specific environment being studied

Economic comparison of centralizing or decentralizing processing facilities for defense transuranic waste

International Nuclear Information System (INIS)

Brown, C.M.

1980-07-01

This study is part of a set of analyses under direction of the Transuranic Waste Management Program designed to provide comprehensive, systematic methodology and support necessary to better understand options for national long-term management of transuranic (TRU) waste. The report summarizes activities to evaluate the economics of possible alternatives in locating facilities to process DOE-managed transuranic waste. The options considered are: (1) Facilities located at all major DOE TRU waste generating sites. (2) Two or three regional facilities. (3) Central processing facility at only one DOE site. The study concludes that processing at only one facility is the lowest cost option, followed, in order of cost, by regional then individual site processing

Leaching of transuranics observed in lysimeter experiments

International Nuclear Information System (INIS)

Erikson, A.; Fredriksson, L.

1994-01-01

A lysimeter installation, primarily designed for studies on plant uptake of transuranics from a number of Swedish soils, has been used also for studies on leaching of nuclides with drainage water from contaminated top soil layers in lysimeter vessels through 65 cm subsoil layers. Interception by ion exchanging resins simulated the nuclide transfer to a field drainage system. The study dealt with the contamination of agricultural land. The results obtained in the experiments have to be interpreted cautiously with regard to their bearing on field conditions. Also, the experimental period has been short when compared with the expected ecological half time of transuranic elements in the environment. However, the results indicate that over a first decade the leaching to drainage systems of transuranics in equilibrium with soil environments is of the same order as that of the crop uptake. The ranges assessed for leaching with an excess precipitation of 200 mm from a deposit in the plough layer to the drainage system during a decade are: for plutonium - 0.003-0.8%, for americium - 0.004-0.006% and for neptunium - 0.03-0.06%. The values for plutonium and americium are very similar except for the organic soil used which held the former nuclide very loosely bound. The leaching of neptunium seems to be ten times that for the other nuclides. It is higher on sandy soils than on organic and clay soils. (author)

Combined transuranic-strontium extraction process

Science.gov (United States)

Horwitz, E. Philip; Dietz, Mark L.

1992-01-01

The transuranic (TRU) elements neptunium, plutonium and americium can be separated together with strontium from nitric acid waste solutions in a single process. An extractant solution of a crown ether and an alkyl(phenyl)-N,N-dialkylcarbanylmethylphosphine oxide in an appropriate diluent will extract the TRU's together with strontium, uranium and technetium. The TRU's and the strontium can then be selectively stripped from the extractant for disposal.

Redefining NHS complaint handling--the real challenge.

Science.gov (United States)

Seelos, L; Adamson, C

1994-01-01

More and more organizations find that a constructive and open dialogue with their customers can be an effective strategy for building long-term customer relations. In this context, it has been recognized that effective complaint-contact handling can make a significant contribution to organizations' attempts to maximize customer satisfaction and loyalty. Within the NHS, an intellectual awareness exists that effective complaint/contact handling can contribute to making services more efficient and cost-effective by developing customer-oriented improvement initiatives. Recent efforts have focused on redefining NHS complaint-handling procedures to make them more user-friendly and effective for both NHS employees and customers. Discusses the challenges associated with opening up the NHS to customer feedback. Highlights potential weaknesses in the current approach and argues that the real challenge is for NHS managers to facilitate a culture change that moves the NHS away from a long-established defensive complaint handling practice.

In situ quantitative determination of transuranic elements in areas of high-level gamma radiation

International Nuclear Information System (INIS)

Brodzinski, R.L.; Wogman, N.A.

1978-01-01

A technique is described for passive neutron monitoring of transuranic elements. The method provides quantitative determinations of transuranic element concentrations in a variety of field situations where no other measurement method is possible. The technique can measure concentrations of transuranic oxides as low as 8 nCi/cm 3 and is capable of operating in gamma radiation fields up to megarads per hour. Information on chemical and isotopic composition can also be obtained from the data. Several successful applications of the technique are discussed

In situ quantitative determination of transuranic elements in areas of high-level gamma radiation

International Nuclear Information System (INIS)

Brodzinski, R.L.; Wogman, N.A.

1978-01-01

A technique is described for passive neutron monitoring of transuranic elements. The method provides quantitative determinations of transuranic element concentrations in a variety of field situations where no other measurement method is possible. The technique can measure concentrations of transuranic oxides as low as 8 nCi/cmsup 3 and is capable of operating in gamma radiation fields up to megarads per hour. Information on chemical and isotopic composition can also be obtained from the data. Several successful applications of the technique are discussed. 1 ref

Innovative technologies for the remediation of transuranic-contaminated landfills. Appendix 13: USA

International Nuclear Information System (INIS)

Kostelnik, K.

2001-01-01

The Transuranic-Contaminated Arid Landfill Stabilization Programme, formerly the Buried Waste Integrated Demonstration Programme, was organized by the Department of Energy, Office of Technology Development, to (a) manage the development of emerging technologies that could be successfully applied to remediation and (b) promote the use of these technologies to improve environmental restoration and waste management operations for transuranic-contaminated landfills in arid environments. Implementing the Transuranic-Contaminated Arid Landfill Stabilization Programme involved three key strategies: 1) A systems engineering approach was used to include an overall perspective of the entire remediation process; 2) State-of-the-art science and technology were sought for improving the remediation system; 3) Integrated product teams which were comprised of end users, regulators, stakeholders, as well as industry partners were formed

Analog elements for transuranic chemistries

International Nuclear Information System (INIS)

Weimer, W.C.

1982-01-01

The analytical technique for measuring trace concentrations of the analog rare earth elements has been refined for optimal detection. The technique has been used to determine the rare earth concentrations in a series of geological and biological materials, including samples harvested from controlled lysimeter investigations. These studies have demonstrated that any of the trivalent rare earth elements may be used as analog elements for the trivalent transuranics, americium and curium

Hanford site transuranic waste certification plan

International Nuclear Information System (INIS)

GREAGER, T.M.

1999-01-01

As a generator of transuranic (TRU) and TRU mixed waste destined for disposal at the Waste Isolation Pilot Plant (WIPP), the Hanford Site must ensure that its TRU waste meets the requirements of U.S. Department of Energy (DOE) Order 5820.2A, ''Radioactive Waste Management, and the Waste Acceptance Criteria for the Waste Isolation Pilot Plant' (DOE 1996d) (WIPP WAC). The WIPP WAC establishes the specific physical, chemical, radiological, and packaging criteria for acceptance of defense TRU waste shipments at WIPP. The WIPP WAC also requires that participating DOE TRU waste generator/treatment/storage sites produce site-specific documents, including a certification plan, that describe their management of TRU waste and TRU waste shipments before transferring waste to WIPP. The Hanford Site must also ensure that its TRU waste destined for disposal at WIPP meets requirements for transport in the Transuranic Package Transporter41 (TRUPACT-11). The U.S. Nuclear Regulatory Commission (NRC) establishes the TRUPACT-I1 requirements in the ''Safety Analysis Report for the TRUPACT-II Shipping Package'' (NRC 1997) (TRUPACT-I1 SARP)

Transuranic contaminated waste form characterization and data base

International Nuclear Information System (INIS)

Kniazewycz, B.G.; McArthur, W.C.

1980-07-01

This volume contains 5 appendices. Title listing are: technologies for recovery of transuranics; nondestructive assay of TRU contaminated wastes; miscellaneous waste characteristics; acceptance criteria for TRU waste; and TRU waste treatment technologies

Processing of transuranic waste at the Savannah River Plant

International Nuclear Information System (INIS)

Daugherty, B.A.; Gruber, L.M.; Mentrup, S.J.

1986-01-01

Transuranic wastes at the Savannah River Plant (SRP) have been retrievably stored on concrete pads since early 1972. This waste is stored primarily in 55-gallon drums and large carbon steel boxes. Higher activity drums are placed in concrete culverts. In support of a National Program to consolidate and permanently dispose of this waste, a major project is planned at SRP to retrieve and process this waste. This project, the TRU Waste Facility (TWF), will provide equipment and processes to retrieve TRU waste from 20-year retrievable storage and prepare it for permanent disposal at the Waste Isolation Pilot Plant (WIPP) geological repository in New Mexico. This project is an integral part of the SRP Long Range TRU Waste Management Program to reduce the amount of TRU waste stored at SRP. The TWF is designed to process 15,000 cubic feet of retrieved waste and 6200 cubic feet of newly generated waste each year of operation. This facility is designed to minimize direct personnel contact with the waste using state-of-the-art remotely operated equipment

Transuranic Waste Characterization Quality Assurance Program Plan

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-04-30

This quality assurance plan identifies the data necessary, and techniques designed to attain the required quality, to meet the specific data quality objectives associated with the DOE Waste Isolation Pilot Plant (WIPP). This report specifies sampling, waste testing, and analytical methods for transuranic wastes.

Transuranic Waste Characterization Quality Assurance Program Plan

International Nuclear Information System (INIS)

1995-01-01

This quality assurance plan identifies the data necessary, and techniques designed to attain the required quality, to meet the specific data quality objectives associated with the DOE Waste Isolation Pilot Plant (WIPP). This report specifies sampling, waste testing, and analytical methods for transuranic wastes

A methodology for characterization and categorization of solutions for micro handling

DEFF Research Database (Denmark)

Gegeckaite, Asta; Hansen, Hans Nørgaard

2005-01-01

is in the range of 0.1-10 micrometers. The importance of considering the entire micro handling scenario is imperative if operational solutions should be designed. The methodology takes into consideration component design (dimension, geometry, material, weight etc.), type of handling operation (characteristics......This paper presents a methodology whereby solutions for micro handling are characterized and classified. The purpose of defining such a methodology is to identify different possible integrated solutions with respect to a specific micro handling scenario in a development phase. The typical accuracy......, tolerances, speed, lot sizes etc.) and handling/gripping principles (contact, non-contact etc.). The methodology will be applied to a case study in order to demonstrate the feasibility of the method....

Resource Conservation and Recovery Act Part B permit application

International Nuclear Information System (INIS)

1991-01-01

The US Department of Energy is currently constructing the Waste Isolation Pilot near Carlsbad, New Mexico. The full-scale pilot plant will demonstrate the feasibility of the safe disposal of defense-related nuclear waste in a bedded salt formation at a depth of 2160 feet below the surface. WIPP will provide for the permanent storage of 25,000 cu ft of remote-handled (RH) transuranic waste and 6,000,000 cu ft of contact-handled (CH) transuranic waste. This paper covers the major mechanical/structural design considerations for the waste hoist and its hoist tower structure. The design of the hoist system and safety features incorporates state-of-the-art technology developed in the hoist and mining industry to ensure safe operation for transporting nuclear waste underground. Also included are design specifications for VOC-10 monitoring system

Resource Conservation and Recovery Act, Part B permit application [for the Waste Isolation Pilot Plant (WIPP)]. Volume 4, Revision 1.0

Energy Technology Data Exchange (ETDEWEB)

1991-12-31

The US Department of Energy is currently constructing the Waste Isolation Pilot near Carlsbad, New Mexico. The full-scale pilot plant will demonstrate the feasibility of the safe disposal of defense-related nuclear waste in a bedded salt formation at a depth of 2160 feet below the surface. WIPP will provide for the permanent storage of 25,000 cu ft of remote-handled (RH) transuranic waste and 6,000,000 cu ft of contact-handled (CH) transuranic waste. This paper covers the major mechanical/structural design considerations for the waste hoist and its hoist tower structure. The design of the hoist system and safety features incorporates state-of-the-art technology developed in the hoist and mining industry to ensure safe operation for transporting nuclear waste underground. Also included are design specifications for VOC-10 monitoring system.

Transuranic waste management program waste form development

International Nuclear Information System (INIS)

Bennett, W.S.; Crisler, L.R.

1981-01-01

To ensure that all technology necessary for long term management of transuranic (TRU) wastes is available, the Department of Energy has established the Transuranic Waste Management Program. A principal focus of the program is development of waste forms that can accommodate the very diverse TRU waste inventory and meet geologic isolation criteria. The TRU Program is following two approaches. First, decontamination processes are being developed to allow removal of sufficient surface contamination to permit management of some of the waste as low level waste. The other approach is to develop processes which will allow immobilization by encapsulation of the solids or incorporate head end processes which will make the solids compatible with more typical waste form processes. The assessment of available data indicates that dewatered concretes, synthetic basalts, and borosilicate glass waste forms appear to be viable candidates for immobilization of large fractions of the TRU waste inventory in a geologic repository

Patterns of transuranic uptake by aquatic organisms: consequences and implications

International Nuclear Information System (INIS)

Eyman, L.D.; Trabalka, J.R.

1980-01-01

Literature on the behavior of plutonium and transuranic elements in aquatic organisms is reviewed. The commonality of observed distribution coefficients over a wide array of aquatic environments (both freshwater and marine) and the lack of biomagnification in aquatic food chains from these environments are demonstrated. These findings lead to the conclusion that physical processes dominate in the transfer of transuranic elements from aquatic environments to man. The question of the nature of the association of plutonium with aquatic biota (surface sorption vs biological incorporation) is discussed as well as the importance of short food chains in the transfer of plutonium to man

Processing and certification of defense transuranic waste at the INEL

International Nuclear Information System (INIS)

Clements, T.L. Jr.; Cargo, C.H.; McKinley, K.B.; Smith, T.H.; Anderson, B.C.

1984-01-01

Since 1970, defense-generated transuranic waste has been placed into 20-year retrievable storage at the Radioactive Waste Management Complex at the Idaho National Engineering Laboratory (INEL). A major objective of the US Department of Energy (DOE) Nuclear Waste Management Program is to remove all retrievably stored transuranic waste form the INEL. To support this objective, the Stored Waste Examination Pilot Plant (SWEPP) and the Process Experimental Pilot Plant (PREPP) are currently being constructed. SWEPP will certify waste, using nondestructive examination techniques, for shipment to the Waste Isolation Pilot Plant (WIPP). PREPP will process uncertifiable waste into a certifiable waste form. 3 references

New transport and handling contract

CERN Multimedia

SC Department

2008-01-01

A new transport and handling contract entered into force on 1.10.2008. As with the previous contract, the user interface is the internal transport/handling request form on EDH: https://edh.cern.ch/Document/TransportRequest/ To ensure that you receive the best possible service, we invite you to complete the various fields as accurately as possible and to include a mobile telephone number on which we can reach you. You can follow the progress of your request (schedule, completion) in the EDH request routing information. We remind you that the following deadlines apply: 48 hours for the transport of heavy goods (up to 8 tonnes) or simple handling operations 5 working days for crane operations, transport of extra-heavy goods, complex handling operations and combined transport and handling operations in the tunnel. For all enquiries, the number to contact remains unchanged: 72202. Heavy Handling Section TS-HE-HH 72672 - 160319

Robot vision system R and D for ITER blanket remote-handling system

International Nuclear Information System (INIS)

Maruyama, Takahito; Aburadani, Atsushi; Takeda, Nobukazu; Kakudate, Satoshi; Nakahira, Masataka; Tesini, Alessandro

2014-01-01

For regular maintenance of the International Thermonuclear Experimental Reactor (ITER), a system called the ITER blanket remote-handling system is necessary to remotely handle the blanket modules because of the high levels of gamma radiation. Modules will be handled by robotic power manipulators and they must have a non-contact-sensing system for installing and grasping to avoid contact with other modules. A robot vision system that uses cameras was adopted for this non-contact-sensing system. Experiments for grasping modules were carried out in a dark room to simulate the environment inside the vacuum vessel and the robot vision system's measurement errors were studied. As a result, the accuracy of the manipulator's movements was within 2.01 mm and 0.31°, which satisfies the system requirements. Therefore, it was concluded that this robot vision system is suitable for the non-contact-sensing system of the ITER blanket remote-handling system

Robot vision system R and D for ITER blanket remote-handling system

Energy Technology Data Exchange (ETDEWEB)

Maruyama, Takahito, E-mail: maruyama.takahito@jaea.go.jp [Japan Atomic Energy Agency, Fusion Research and Development Directorate, Naka, Ibaraki-ken 311-0193 (Japan); Aburadani, Atsushi; Takeda, Nobukazu; Kakudate, Satoshi; Nakahira, Masataka [Japan Atomic Energy Agency, Fusion Research and Development Directorate, Naka, Ibaraki-ken 311-0193 (Japan); Tesini, Alessandro [ITER Organization, Route de Vinon sur Verdon, 13115 St Paul Lez Durance (France)

2014-10-15

For regular maintenance of the International Thermonuclear Experimental Reactor (ITER), a system called the ITER blanket remote-handling system is necessary to remotely handle the blanket modules because of the high levels of gamma radiation. Modules will be handled by robotic power manipulators and they must have a non-contact-sensing system for installing and grasping to avoid contact with other modules. A robot vision system that uses cameras was adopted for this non-contact-sensing system. Experiments for grasping modules were carried out in a dark room to simulate the environment inside the vacuum vessel and the robot vision system's measurement errors were studied. As a result, the accuracy of the manipulator's movements was within 2.01 mm and 0.31°, which satisfies the system requirements. Therefore, it was concluded that this robot vision system is suitable for the non-contact-sensing system of the ITER blanket remote-handling system.

224-T Transuranic Waste Storage and Assay Facility dangerous waste permit application

International Nuclear Information System (INIS)

1992-01-01

Westinghouse Hanford Company is a major contractor to the US Department of Energy Richland Field Office and serves as cooperator of the 224-T Transuranic Waste Storage and Assay Facility, the storage unit addressed in this permit application. At the time of submission of this portion of the Hanford Facility. Dangerous Waste Permit Application covering the 224-T Transuranic Waste Storage and Assay Facility, many issues identified in comments to the draft Hanford Facility Dangerous Waste Permit remain unresolved. This permit application reflects the positions taken by the US Department of Energy, Company on the draft Hanford Facility Dangerous Waste Permit and may not be read to conflict with those comments. The 224-T Transuranic Waste Storage and Assay Facility Dangerous Waste Permit Application (Revision 0) consists of both a Part A and Part B permit application. An explanation of the Part A revisions associated with this unit, including the Part A revision currently in effect, is provided at the beginning of the Part A section. The Part B consists of 15 chapters addressing the organization and content of the Part B Checklist prepared by the Washington State Department of Ecology (Ecology 1987). The 224-T Transuranic Waste Storage and Assay Facility Dangerous Waste Permit Application contains information current as of March 1, 1992

Project Execution Plan for the Remote Handled Low-Level Waste Disposal Project

Energy Technology Data Exchange (ETDEWEB)

Danny Anderson

2014-07-01

As part of ongoing cleanup activities at the Idaho National Laboratory (INL), closure of the Radioactive Waste Management Complex (RWMC) is proceeding under the Comprehensive Environmental Response, Compensation, and Liability Act (42 USC 9601 et seq. 1980). INL-generated radioactive waste has been disposed of at RWMC since 1952. The Subsurface Disposal Area (SDA) at RWMC accepted the bulk of INL’s contact and remote-handled low-level waste (LLW) for disposal. Disposal of contact-handled LLW and remote-handled LLW ion-exchange resins from the Advanced Test Reactor in the open pit of the SDA ceased September 30, 2008. Disposal of remote-handled LLW in concrete disposal vaults at RWMC will continue until the facility is full or until it must be closed in preparation for final remediation of the SDA (approximately at the end of fiscal year FY 2017). The continuing nuclear mission of INL, associated ongoing and planned operations, and Naval spent fuel activities at the Naval Reactors Facility (NRF) require continued capability to appropriately dispose of contact and remote handled LLW. A programmatic analysis of disposal alternatives for contact and remote-handled LLW generated at INL was conducted by the INL contractor in Fiscal Year 2006; subsequent evaluations were completed in Fiscal Year 2007. The result of these analyses was a recommendation to the Department of Energy (DOE) that all contact-handled LLW generated after September 30, 2008, be disposed offsite, and that DOE proceed with a capital project to establish replacement remote-handled LLW disposal capability. An analysis of the alternatives for providing replacement remote-handled LLW disposal capability has been performed to support Critical Decision-1. The highest ranked alternative to provide this required capability has been determined to be the development of a new onsite remote-handled LLW disposal facility to replace the existing remote-handled LLW disposal vaults at the SDA. Several offsite DOE

Colloid generation and solid-liquid distribution of transuranic elements in natural aquifier systems

International Nuclear Information System (INIS)

Rommel, H.; Kim, J.I.

1986-01-01

The sorption and desorption behaviour of transuranic elements in the presence of their pseudocolloids has been investigated in deep geological aquifer systems at Gorleben area. The generation of transuranic colloids and their influence on the determination of distribution coefficients in a laboratory experimental system are evaluated quantitatively. Discussion is made on the possible extrapolation of laboratory results to natural systems. (author)

Colloid generation and solid-liquid distribution of transuranic elements in natural aquifer systems

International Nuclear Information System (INIS)

Kim, J.I.; Rommel, H.

1986-01-01

The sorption and desorption behaviour of transuranic elements in the presence of their pseudocolloids has been investigated in deep geological aquifer systems at Gorleben area. The generation of transuranic colloids and their influence on the determination of distribution coefficients in a laboratory experimental system are evaluated quantitatively. Discussion is made on the possible extrapolation of laboratory results to natural systems. (orig.)

Waste Isolation Pilot Plant Title I operator dose calculations. Final report, LATA report No. 90

International Nuclear Information System (INIS)

Hughes, P.S.; Rigdon, L.D.

1980-02-01

The radiation exposure dose was estimated for the Waste Isolation Pilot Plant (WIPP) operating personnel who do the unloading and transporting of the transuranic contact-handled waste. Estimates of the radiation source terms for typical TRU contact-handled waste were based on known composition and properties of the waste. The operations sequence for waste movement and storage in the repository was based upon the WIPP Title I data package. Previous calculations had been based on Conceptual Design Report data. A time and motion sequence was developed for personnel performing the waste handling operations both above and below ground. Radiation exposure calculations were then performed in several fixed geometries and folded with the time and motion studies for individual workers in order to determine worker exposure on an annual basis

Unvented Drum Handling Plan

International Nuclear Information System (INIS)

MCDONALD, K.M.

2000-01-01

This drum-handling plan proposes a method to deal with unvented transuranic drums encountered during retrieval of drums. Finding unvented drums during retrieval activities was expected, as identified in the Transuranic (TRU) Phase I Retrieval Plan (HNF-4781). However, significant numbers of unvented drums were not expected until excavation of buried drums began. This plan represents accelerated planning for management of unvented drums. A plan is proposed that manages unvented drums differently based on three categories. The first category of drums is any that visually appear to be pressurized. These will be vented immediately, using either the Hanford Fire Department Hazardous Materials (Haz. Mat.) team, if such are encountered before the facilities' capabilities are established, or using internal capabilities, once established. To date, no drums have been retrieved that showed signs of pressurization. The second category consists of drums that contain a minimal amount of Pu isotopes. This minimal amount is typically less than 1 gram of Pu, but may be waste-stream dependent. Drums in this category are assayed to determine if they are low-level waste (LLW). LLW drums are typically disposed of without venting. Any unvented drums that assay as TRU will be staged for a future venting campaign, using appropriate safety precautions in their handling. The third category of drums is those for which records show larger amounts of Pu isotopes (typically greater than or equal to 1 gram of Pu). These are assumed to be TRU and are not assayed at this point, but are staged for a future venting campaign. Any of these drums that do not have a visible venting device will be staged awaiting venting, and will be managed under appropriate controls, including covering the drums to protect from direct solar exposure, minimizing of container movement, and placement of a barrier to restrict vehicle access. There are a number of equipment options available to perform the venting. The

Waste Isolation Pilot Plant transuranic wastes experimental characterization program: executive summary

International Nuclear Information System (INIS)

Molecke, M.A.

1978-11-01

A general overview of the Waste Isolation Pilot Plant transuranic wastes experimental characterization program is presented. Objectives and outstanding concerns of this program are discussed. Characteristics of transuranic wastes are also described. Concerns for the terminal isolation of such wastes in a deep bedded salt facility are divided into two phases, those during the short-term operational phase of the facility, and those potentially occurring in the long-term, after decommissioning of the repository. An inclusive summary covering individual studies, their importance to the Waste Isolation Pilot Plant, investigators, general milestones, and comments are presented

Resource Conservation and Recovery Act closure plan for the Intermediate-Level Transuranic Storage Facility mixed waste container storage units

International Nuclear Information System (INIS)

Nolte, E.P.; Spry, M.J.; Stanisich, S.N.

1992-11-01

This document describes the proposed plan for clean closure of the Intermediate-Level Transuranic Storage Facility mixed waste container storage units at the Idaho National Engineering Laboratory in accordance with the Resource Conservation and Recovery Act closure requirements. Descriptions of the location, size, capacity, history, and current status of the units are included. The units will be closed by removing waste containers in storage, and decontamination structures and equipment that may have contacted waste. Sufficient sampling and documentation of all activities will be performed to demonstrate clean closure. A tentative schedule is provided in the form of a milestone chart

Distribution of transuranic elements in bone.

Science.gov (United States)

Durbin, P W

1992-01-01

The transport, retention, and excretion of transuranic elements from the body have been widely studied for many years. A summary of the results is given with an emphasis on the distribution of these elements in bone. Implications of these studies for understanding the relationships between lead in blood and lead in bone are presented. The expected distribution of lead at various bone sites is also considered.

Reliability evaluation methodologies for ensuring container integrity of stored transuranic (TRU) waste

International Nuclear Information System (INIS)

Smith, K.L.

1995-06-01

This report provides methodologies for providing defensible estimates of expected transuranic waste storage container lifetimes at the Radioactive Waste Management Complex. These methodologies can be used to estimate transuranic waste container reliability (for integrity and degradation) and as an analytical tool to optimize waste container integrity. Container packaging and storage configurations, which directly affect waste container integrity, are also addressed. The methodologies presented provide a means for demonstrating Resource Conservation and Recovery Act waste storage requirements

Transuranic element uptake and cycling in a forest over an old burial ground

International Nuclear Information System (INIS)

Murphy, C.E.; Tuckfield, R.C.

1994-01-01

The consequences of returning the Savannah River Site (SRS) burial ground area to general public access at the time of completion of the SRS mission is being investigated. This study was established with the objective of determining the uptake of buried, low-level, transuranic waste from unlined earthen trenches by forest vegetation. From SRS startup in 1953 through 1974, solid waste contaminated with α-emitting transuranic nuclides was buried, unencapsulated, in earthen trenches. Burial records show that this material includes plutonium-238 ( 238 Pu), plutonium isotopes 239 and 240 ( 239,240 Pu), americium-241 ( 241 Am), and neptunium-237 ( 237 Np). In 1979, two tree plots were established, one over a trench in the burial ground and the other in an area without trenches. In the 2 years following establishment of the tree plots, 1979 and 1980, whole trees of each species were collected from each plot and analyzed for 239 Pu and 238 Pu. Beginning in 1986, needle samples were collected from selected pine trees in each of the plots. Because of poor growth and survival, the hardwood trees were not sampled after 1980. The results of data analysis support the conclusions that: (1) there is more 238 Pu uptake by pine tree seedlings than the other species, (2) there is greater transuranic radionuclide uptake in grown pine trees than in seedlings, and (3) there are greater concentrations of transuranic radionuclides in the grown pine trees on the trench plots than in the pine trees on the control plot. These data indicate that tree roots will extract transuranic isotopes from buried, low level waste. The amount of radioisotopes moved from the trenches to the surface is small and the level in the trees is low enough that dose from direct exposure will be very small. A model was developed to estimate the potential for the transfer from the SRS alpha trenches. The results suggest that even following 100 years of transport, the transuranic, alpha dose from consuming food crops

Ergonomic design and evaluation of the handle for an endoscopic dissector.

Science.gov (United States)

Shimomura, Yoshihiro; Minowa, Keita; Kawahira, Hiroshi; Katsuura, Tetsuo

2016-05-01

The purpose of this study was to design an endoscopic dissector handle and objectively assess its usability. The handles were designed with increased contact area between the fingers and thumb and the eye rings, and the eye rings were modified to have a more perpendicular insertion angle to the finger midline. Four different handle models were compared, including a conventional product. Subjects performed dissection, exclusion, grasping, precision manipulation and precision handling tasks. Electromyography and subjective evaluations were measured. Compared to conventional handles, the designated handle reduced the muscle load in the extensor and flexor muscles of the forearm and increased subjective stability. The activity of the first dorsal interosseous muscle was sometimes influenced by the shape of the other parts. The ergonomically designed endoscopic dissector handle used in this study achieved high usability. Medical instrument designs based on ergonomic concepts should be assessed with objective indices. Practitioner Summary: The endoscopic dissector handles were designed with increased contact area and more suitable insertion angle between the fingers and thumb and the eye rings. Compared to conventional handles, the designated handle reduced the muscle load in the extensor and flexor muscles of the forearm and increased subjective stability.

Utilization of borosilicate glass for transuranic waste immobilization

International Nuclear Information System (INIS)

Ledford, J.A.; Williams, P.M.

1979-01-01

Incinerated transuranic waste and other low-level residues have been successfully vitrified by mixing with boric acid and sodium carbonate and heating to 1050 0 C in a bench-scale continuous melter. The resulting borosilicate glass demonstrates excellent mechanical durability and chemical stability

An evaluation of the concept of transuranic burning using liquid metal reactors

International Nuclear Information System (INIS)

Rodwell, E.; Shaw, R.A.; Williams, R.F.

1991-03-01

The evaluation investigates the potential benefits to radioactive waste disposal of separating the transuranic elements from spent reactor fuel before the spent fuel is disposed of in geologic repositories. The evaluation addresses the question whether the benefits to radioactive waste disposal would justify processing the fuel to separate the transuranics, plus a liquid metal reactor (LMR) deployment program to transmute the separated transuranics. The evaluation concludes that adoption of a process-before-disposal policy for all the spent fuel from the light water reactors (LWRs) would accrue only modest benefits with respect to the accumulation of uranium mill tailings, the national inventory of transuranics and the licensing of a geologic repository. It is likely that this process-before-disposal policy would incur a large cost penalty, encounter major institutional difficulties, multiply licensing hurdles, and amplify political and public opposition to the overall nuclear power program. However, plutonium from spent LWR fuel is projected to be substantially more economic than enriched uranium, as fissile material for startup of LMRs when LMR deployment becomes economically justified. At that time, the LMR would fulfill its role as a reactor system that would protect the nation from diminishing energy resources. Development tasks towards defining and developing the most cost-effective LMR and associated fuel cycle remain very important. 29 refs., 3 figs., 18 tabs

Transuranics in bone of deceased former residents of Rongelap Atoll, Marshall Islands

International Nuclear Information System (INIS)

Franke, B.; Schupfner, R.; Schuettelkopf, H.; Spennemann, D.H.R.

1995-01-01

Rongelap Atoll received intensive fallout from the 1 March 1954 Bravo thermonuclear test 105 miles upwind at Bikini. Fearful of their continued exposure to radiation, the residences of Rongelap Atoll went into voluntary exile in 1985. Transuranic soil concentrations on Rongelap Island are about 2-3 orders of magnitude greater than the average for the Northern hemisphere; the three dominating transuranic are 239,240 Pu and 241 Am. Only conflicting information has been available about the extent of transuranic uptake by the Rongelap community. As part of the Rongelap Resettlement Project, the community endorsed the exhumation of bones of deceased former atoll residents to provide an independent estimate of plutonium intake. This approach has the advantage of reducing the uncertainties associated with pathway modeling and the interpretation of urine data. Six graves (4 adults, 2 children) were selected for exhumation. Femora and tibiae were selected as well as humeri from the children's graves. The rest of the remains were left undisturbed. The results of the analysis of 239,240 Pu and 241 Am are presented. Assuming that the data can be considered as representative for the Rongelap population as a whole, the contamination with transuranics on Rongelap Atoll appears to result in radiation exposures in the order of 1% of the compliance limit of 100 mrem (1 mSv) effective dose equivalent per year. (author)

Transuranics in bone of deceased former residents of Rongelap Atoll, Marshall Islands

Energy Technology Data Exchange (ETDEWEB)

Franke, B. [Institute for Energy and Environmental Research, Takoma Park, MD (United States)]|[Institut fuer Energie- und Umweltforschung e.V., Heidelberg (Germany); Schupfner, R.; Schuettelkopf, H. [Regensburg Univ. (Germany). Lab. for Environmental Radioactivity; Spennemann, D.H.R. [Charles Sturt Univ., Albury (Australia). School of Environmental and Information Sciences

1995-11-01

Rongelap Atoll received intensive fallout from the 1 March 1954 Bravo thermonuclear test 105 miles upwind at Bikini. Fearful of their continued exposure to radiation, the residences of Rongelap Atoll went into voluntary exile in 1985. Transuranic soil concentrations on Rongelap Island are about 2-3 orders of magnitude greater than the average for the Northern hemisphere; the three dominating transuranic are {sup 239,240}Pu and {sup 241}Am. Only conflicting information has been available about the extent of transuranic uptake by the Rongelap community. As part of the Rongelap Resettlement Project, the community endorsed the exhumation of bones of deceased former atoll residents to provide an independent estimate of plutonium intake. This approach has the advantage of reducing the uncertainties associated with pathway modeling and the interpretation of urine data. Six graves (4 adults, 2 children) were selected for exhumation. Femora and tibiae were selected as well as humeri from the children`s graves. The rest of the remains were left undisturbed. The results of the analysis of {sup 239,240}Pu and {sup 241}Am are presented. Assuming that the data can be considered as representative for the Rongelap population as a whole, the contamination with transuranics on Rongelap Atoll appears to result in radiation exposures in the order of 1% of the compliance limit of 100 mrem (1 mSv) effective dose equivalent per year. (author).

Transuranics in bone of deceased former residents of Rongelap Atoll, Marshall Islands.

Science.gov (United States)

Franke, B; Schupfner, R; Schüttelkopf, H; Spennemann, D H

1995-11-01

Rongelap Atoll received intensive fallout from the 1 March 1954 Bravo thermonuclear test 105 miles upwind at Bikini. Fearful of their continued exposure to radiation, the residents of Rongelap Atoll went into voluntary exile in 1985. Transuranic soil concentrations on Rongelap Island are about 2-3 orders of magnitude greater than the average for the Northern hemisphere; the three dominating transuranics are 239,240Pu and 241Am. Only conflicting information has been available about the extent of transuranic uptake by the Rongelap community. As part of the Rongelap Resettlement Project, the community endorsed the exhumation of bones of deceased former atoll residents to provide an independent estimate of plutonium intake. This approach has the advantage of reducing the uncertainties associated with pathway modeling and the interpretation of urine data. Six graves (4 adults, 2 children) were selected for exhumation. Femora and tibiae were selected as well as humeri from the children's graves. The rest of the remains was left undisturbed. The results of the analysis of 239,240Pu and 241Am are presented. Assuming that the data can be considered as representative for the Rongelap population as a whole, the contamination with transuranics on Rongelap Atoll appears to result in radiation exposures in the order of 1% of the compliance limit of 100 mrem (1 mSv) effective dose equivalent per year.

Geochemistry of transuranic elements at Bikini Atoll

International Nuclear Information System (INIS)

Schell, W.R.; Lowman, F.G.; Marshall, R.P.

1980-01-01

The distribution of transuranic and other radionuclides in the marine environment at Bikini Atoll was studied to better understand the geochemical cycling of radionuclides produced by nuclear testing between 1946 and 1958. The reef areas, which are washed continually by clean ocean water, have low levels of radionuclide concentrations. Radionuclides are contained in fallout particles of pulverized coral. In the water these particles may dissolve, be transported by currents within the Atoll, or enter the North Equatorial Current by tidal exchange of water in the lagoon. The transuranic elements are distributed widely in sediments over the northwest quadrant of the Atoll, which suggests that this area serves as a settling basin for particles. The distribution of plutonium in the water column indicates that plutonium in the sediments is released to the bottom waters and then is transported and diluted by the prevailing currents. Upon interaction with the lagoon environment, plutonium occurs in several physicochemical states. Laboratory tests and field studies at Bikini show that approximately 15% of the plutonium is associated with the colloidal fraction

Dosimetry of incorporated transuranic radionuclides

International Nuclear Information System (INIS)

Loessner, V.

1983-01-01

Modern in vivo and in vitro techniques for detecting transuranic radionuclides within the human body are described with special emphasis on multiparameter measuring methods developed at the National Board of Nuclear Safety and Radiation Protection. Furthermore, problems related to calibration and interpretation of measuring data are discussed and new methods presented for the calculation of committed dose equivalents on the basis of data from ICRP Publication 30. Also included is an introductory chapter on radiobiological fundamentals of intake, translocation and metabolism of these nuclides. (author)

Effects of transuranics on pulmonary lymph nodes of rodents

International Nuclear Information System (INIS)

Sanders, C.L.

1976-01-01

Pulmonary lymph nodes have been suggested as the ''critical'' tissue for insoluble, inhaled transuranic compounds owing to the high concentration of transuranics in these lymph nodes. About 800 rats were given from 0.2 to 3600 nCi of 238 PuO 2 or 239 PuO 2 by inhalation, intratracheal instillation, intrapleural injection, or intraperitoneal injection. From about 1 to 10 percent of deposited plutonium was translocated to pulmonary lymph nodes, the amount depending on the time after deposition and the route of administration; 238 PuO 2 was cleared from pulmonary lymph nodes faster than 239 PuO 2 owing to the greater in vivo solubility of 238 PuO 2 . No primary tumors of pulmonary lymph nodes were observed, indicating that this tissue was not the critical tissue for carcinogenic induction

Environmental aspects of the transuranics: a selected, annotated bibliography

Energy Technology Data Exchange (ETDEWEB)

Fore, C.S.; Martin, F.M.; Faust, R.A. (comp.)

1976-07-01

This bibliography of 500 references is compiled from the Data Base on the Environmental Aspects of the Transuranics built to provide information support to the Nevada Applied Ecology Group (NAEG) of ERDA`s Nevada Operations Office. The general scope is environmental aspects of uranium and the transuranic elements, with emphasis on plutonium. Laboratory and field studies dealing with the effects of plutonium-239 on animals are highlighted in this bibliography. Supporting information on ecology of the Nevada Test Site and reviews on the effects of other radionuclides upon man and his environment has been included at the request of the NAEG. The references are arranged by subject category with first authors appearing alphabetically in each category. Indexes are given for author, geographic location, keywords, taxons, permuted title and publication description.

Environmental aspects of the transuranics: a selected, annotated bibliography

International Nuclear Information System (INIS)

Fore, C.S.; Martin, F.M.; Faust, R.A.

1976-07-01

This bibliography of 500 references is compiled from the Data Base on the Environmental Aspects of the Transuranics built to provide information support to the Nevada Applied Ecology Group (NAEG) of ERDA's Nevada Operations Office. The general scope is environmental aspects of uranium and the transuranic elements, with emphasis on plutonium. Laboratory and field studies dealing with the effects of plutonium-239 on animals are highlighted in this bibliography. Supporting information on ecology of the Nevada Test Site and reviews on the effects of other radionuclides upon man and his environment has been included at the request of the NAEG. The references are arranged by subject category with first authors appearing alphabetically in each category. Indexes are given for author, geographic location, keywords, taxons, permuted title and publication description

Environmental aspects of the transuranics. A selected, annotated bibliography

International Nuclear Information System (INIS)

Martin, F.M.; Faust, R.A.; Sanders, C.T.

1975-07-01

This bibliography of 470 references is from the computer file built to provide information support to the Nevada Applied Ecology Group (NAEG) of ERDA's Nevada Operations Office. The general scope is environmental aspects of uranium and the transuranic elements, with emphasis on plutonium. Biological aspects of the transuranics is highlighted in this bibliography. In addition, supporting materials involving basic ecology studies, ecology of the Nevada Test Site, and reviews on other radionuclides are entered at the request of the NAEG. Significant numeric data is shown in tabular display or is noted for reference to the original document. The references are arranged by subject category with first authors arranged alphabetically within the category. Indexes are given for author, keywords, geographic location, permuted title, taxons, and publication description. (U.S.)

Transuranic waste baseline inventory report. Revision No. 3

International Nuclear Information System (INIS)

1996-06-01

The Transuranic Waste Baseline Inventory Report (TWBIR) establishes a methodology for grouping wastes of similar physical and chemical properties from across the U.S. Department of Energy (DOE) transuranic (TRU) waste system into a series of open-quotes waste profilesclose quotes that can be used as the basis for waste form discussions with regulatory agencies. The purpose of Revisions 0 and 1 of this report was to provide data to be included in the Sandia National Laboratories/New Mexico (SNL/NM) performance assessment (PA) processes for the Waste Isolation Pilot Plant (WIPP). Revision 2 of the document expanded the original purpose and was also intended to support the WIPP Land Withdrawal Act (LWA) requirement for providing the total DOE TRU waste inventory. The document included a chapter and an appendix that discussed the total DOE TRU waste inventory, including nondefense, commercial, polychlorinated biphenyls (PCB)-contaminated, and buried (predominately pre-1970) TRU wastes that are not planned to be disposed of at WIPP

Controlled-air incineration of transuranic-contaminated solid waste

International Nuclear Information System (INIS)

Borduin, L.C.; Draper, W.E.; Koenig, R.A.; Neuls, A.S.; Warner, C.L.

1976-01-01

A controlled-air incinerator and an associated high-energy aqueous off-gas cleaning system are being installed at the Los Alamos Scientific Laboratory (LASL) Transuranic Waste Treatment Development Facility (TDF) for evaluation as a low-level transuranic-contaminated (TRU) solid waste volume reduction process. Program objectives are: (1) assembly and operation of a production scale (45 kg/hr) operation of ''off-the-shelf'' components representative of current incineration and pollution control technology; (2) process development and modification to meet radioactive health and safety standards, and (3) evaluation of the process to define the advantages and limitations of conventional technology. The results of the program will be the design specifications and operating procedures necessary for successful incineration of TRU waste. Testing, with nonradioactive waste, will begin in October 1976. This discussion covers commercially available incinerator and off-gas cleaning components, the modifications required for radioactive service, process components performance expectations, and a description of the LASL experimental program

Sampling soils for transuranic nuclides: a review

International Nuclear Information System (INIS)

Fowler, E.B.; Essington, E.H.

1976-01-01

A review of the literature pertinent to the sampling of soils for radionuclides is presented; emphasis is placed on transuranic nuclides. Sampling of soils is discussed relative to systems of heterogeneous distributions and varied particle sizes encountered in certain environments. Sampling methods that have been used for two different sources of contamination, global fallout, and accidental or operational releases, are included

Preliminary analysis of treatment strategies for transuranic wastes from reprocessing plants

International Nuclear Information System (INIS)

Ross, W.A.; Schneider, K.J.; Swanson, J.L.; Yasutake, K.M.; Allen, R.P.

1985-07-01

This document provides a comparison of six treatment options for transuranic wastes (TRUW) resulting from the reprocessing of commercial spent fuel. Projected transuranic waste streams from the Barnwell Nuclear Fuel Plant (BNFP), the reference fuel reprocessing plant in this report, were grouped into the five categories of hulls and hardware, failed equipment, filters, fluorinator solids, and general process trash (GPT) and sample and analytical cell (SAC) wastes. Six potential treatment options were selected for the five categories of waste. These options represent six basic treatment objectives: (1) no treatment, (2) minimum treatment (compaction), (3) minimum number of processes and products (cementing or grouting), (4) maximum volume reduction without decontamination (melting, incinerating, hot pressing), (5) maximum volume reduction with decontamination (decontamination, treatment of residues), and (6) noncombustible waste forms (melting, incinerating, cementing). Schemes for treatment of each waste type were selected and developed for each treatment option and each type of waste. From these schemes, transuranic waste volumes were found to vary from 1 m 3 /MTU for no treatment to as low as 0.02 m 3 /MTU. Based on conceptual design requirements, life-cycle costs were estimated for treatment plus on-site storage, transportation, and disposal of both high-level and transuranic wastes (and incremental low-level wastes) from 70,000 MTU. The study concludes that extensive treatment is warranted from both cost and waste form characteristics considerations, and that the characteristics of most of the processing systems used are acceptable. The study recommends that additional combinations of treatment methods or strategies be evaluated and that in the interim, melting, incineration, and cementing be further developed for commercial TRUW. 45 refs., 9 figs., 32 tabs

Preliminary analysis of treatment strategies for transuranic wastes from reprocessing plants

Energy Technology Data Exchange (ETDEWEB)

Ross, W.A.; Schneider, K.J.; Swanson, J.L.; Yasutake, K.M.; Allen, R.P.

1985-07-01

This document provides a comparison of six treatment options for transuranic wastes (TRUW) resulting from the reprocessing of commercial spent fuel. Projected transuranic waste streams from the Barnwell Nuclear Fuel Plant (BNFP), the reference fuel reprocessing plant in this report, were grouped into the five categories of hulls and hardware, failed equipment, filters, fluorinator solids, and general process trash (GPT) and sample and analytical cell (SAC) wastes. Six potential treatment options were selected for the five categories of waste. These options represent six basic treatment objectives: (1) no treatment, (2) minimum treatment (compaction), (3) minimum number of processes and products (cementing or grouting), (4) maximum volume reduction without decontamination (melting, incinerating, hot pressing), (5) maximum volume reduction with decontamination (decontamination, treatment of residues), and (6) noncombustible waste forms (melting, incinerating, cementing). Schemes for treatment of each waste type were selected and developed for each treatment option and each type of waste. From these schemes, transuranic waste volumes were found to vary from 1 m/sup 3//MTU for no treatment to as low as 0.02 m/sup 3//MTU. Based on conceptual design requirements, life-cycle costs were estimated for treatment plus on-site storage, transportation, and disposal of both high-level and transuranic wastes (and incremental low-level wastes) from 70,000 MTU. The study concludes that extensive treatment is warranted from both cost and waste form characteristics considerations, and that the characteristics of most of the processing systems used are acceptable. The study recommends that additional combinations of treatment methods or strategies be evaluated and that in the interim, melting, incineration, and cementing be further developed for commercial TRUW. 45 refs., 9 figs., 32 tabs.

Environmental aspects of the transuranics: a selected, annotated bibliography

International Nuclear Information System (INIS)

Ensminger, J.T.; Martin, F.M.; Fore, C.S.

1977-03-01

This eighth published bibliography of 427 references is compiled from the Nevada Applied Ecology Information Center's Data Base on the Environmental Aspects of the Transuranics. The data base was built to provide information support to the Nevada Applied Ecology Group (NAEG) of ERDA's Nevada Operations Office. The general scope covers environmental aspects of uranium and the transuranic elements, with emphasis on plutonium. This bibliography highlights literature on plutonium 238 and 239 and americium in the critical organs of man and animals. Supporting information on ecology of the Nevada Test Site and reviews and summarizing literature on other radionuclides have been included at the request of the NAEG. The references are arranged by subject category with leading authors appearing alphabetically in each category. Indexes are provided for author(s), geographic location, keyword(s), taxon, title, and publication description

Review of biokinetic and biological transport of transuranic radionuclides in the marine environment

International Nuclear Information System (INIS)

Beasley, T.M.; Cross, F.A.

1980-01-01

Present understanding of the uptake, retention, and loss of transuranic radionuclides by marine biota is limited. Laboratory experiments have demonstrated that for certain species assimilation of plutonium and americium from labeled food is an efficient process and that direct uptake from seawater is important in the bioaccumulation of all transuranic radionuclides studied to date. Organisms appear to play an important role in the vertical transport of these radioelements from the surface layers of the ocean to greater depths

Hanford Site Hazardous waste determination report for transuranic debris waste streams NPFPDL2A

International Nuclear Information System (INIS)

WINTERHALDER, J.A.

1999-01-01

This hazardous waste determination report (Report) describes the process and information used on the Hanford Site to determine that waste stream number NPFPDLZA, consisting of 30 containers of contact-handled transuranic debris waste, is not hazardous waste regulated by the Resource Conservation and Recovery Act (RCRA) or the New Mexico Hazardous Waste Act. For a waste to be hazardous under these statutes, the waste either must be specifically listed as a hazardous waste, or exhibit one or more of the characteristics of a hazardous waste, Le., ignitability, corrosivity, reactivity, or toxicity. Waste stream NPFPDLZA was generated, packaged, and placed into storage between 1993 and 1997. Extensive knowledge of the waste generating process, facility operational history, and administrative controls and operating procedures in effect at the time of generation, supported the initial nonhazardous waste determination. Because of the extent and reliability of information pertaining to this waste type, and the total volume of waste in the debris matrix parameter category, the Hanford Site is focusing initial efforts on this and similar waste streams for the first shipment to the Waste Isolation Pilot Plant (WIPP). RCRA regulations authorize hazardous waste determinations to be made either by using approved sampling and analysis methods or by applying knowledge of the waste in light of the materials or the process(es) used. This latter approach typically is referred to as process knowledge. The Transuranic Waste Characterization Quality Assurance Program Plan (CAO-94-1010) for WIPP refers to acceptable knowledge in essentially the same terms; acceptable knowledge as used throughout this Report is synonymous with the term process knowledge. The 30 containers addressed in this Report were characterized by the following methods: Acceptable knowledge; Nondestructive examination using real-time radiography; Visual examination; and Headspace gas sampling and analysis. The initial

Hanford Site Hazardous waste determination report for transuranic debris waste streams NPFPDL2A

Energy Technology Data Exchange (ETDEWEB)

WINTERHALDER, J.A.

1999-09-29

This hazardous waste determination report (Report) describes the process and information used on the Hanford Site to determine that waste stream number NPFPDLZA, consisting of 30 containers of contact-handled transuranic debris waste, is not hazardous waste regulated by the Resource Conservation and Recovery Act (RCRA) or the New Mexico Hazardous Waste Act. For a waste to be hazardous under these statutes, the waste either must be specifically listed as a hazardous waste, or exhibit one or more of the characteristics of a hazardous waste, Le., ignitability, corrosivity, reactivity, or toxicity. Waste stream NPFPDLZA was generated, packaged, and placed into storage between 1993 and 1997. Extensive knowledge of the waste generating process, facility operational history, and administrative controls and operating procedures in effect at the time of generation, supported the initial nonhazardous waste determination. Because of the extent and reliability of information pertaining to this waste type, and the total volume of waste in the debris matrix parameter category, the Hanford Site is focusing initial efforts on this and similar waste streams for the first shipment to the Waste Isolation Pilot Plant (WIPP). RCRA regulations authorize hazardous waste determinations to be made either by using approved sampling and analysis methods or by applying knowledge of the waste in light of the materials or the process(es) used. This latter approach typically is referred to as process knowledge. The Transuranic Waste Characterization Quality Assurance Program Plan (CAO-94-1010) for WIPP refers to acceptable knowledge in essentially the same terms; acceptable knowledge as used throughout this Report is synonymous with the term process knowledge. The 30 containers addressed in this Report were characterized by the following methods: Acceptable knowledge; Nondestructive examination using real-time radiography; Visual examination; and Headspace gas sampling and analysis. The initial

Flibe blanket concept for transmuting transuranic elements and long lived fission products

International Nuclear Information System (INIS)

Gohar, Y.

2000-01-01

A Molten salt (Flibe) fusion blanket concept has been developed to solve the disposition problems of the spent nuclear fuel and the transuranic elements. This blanket concept can achieve the top rated solution, the complete elimination of the transuranic elements and the long-lived fission products. Small driven fusion devices with low neutron wall loading and low neutron fluence can perform this function. A 344-MW integrated fusion power from D-T plasmas for thirty years with an availability factor of 0.75 can dispose of 70,000 tons of the US inventory of spent nuclear fuel generated up to the year 2015. In addition, the utilization of this blanket concept eliminates the need for a geological repository site, which is a major advantage. This application provides an excellent opportunity to develop and to enhance the public acceptance of the fusion energy for the future. The energy from the transmutation process is utilized to produce revenue. Flibe, lithium-lead eutectic, and liquid lead are possible candidates. The liquid blankets have several features, which are suited for W application. It can operate at constant thermal power without interruption for refueling by adjusting the concentration of the transuranic elements and lithium-6. These liquids operate at low-pressure, which reduces the primary stresses in the structure material. Development and fabrication costs of solid transuranic materials are eliminated. Burnup limit of the transuranic elements due to radiation effects is eliminated. Heat is generated within the liquid, which simplifies the heat removal process without producing thermal stresses. These blanket concepts have large negative temperature coefficient with respect to the blanket reactivity, which enhances the safety performance. These liquids are chemically and thermally stable under irradiation conditions, which minimize the radioactive waste volume. The operational record of the Molten Salt Breeder Reactor with Flibe was very successful

Synthesis of neutron-rich transuranic nuclei in fissile spallation targets

Energy Technology Data Exchange (ETDEWEB)

Mishustin, Igor, E-mail: mishustin@fias.uni-frankfurt.de [Frankfurt Institute for Advanced Studies, J.-W. Goethe University, 60438 Frankfurt am Main (Germany); “Kurchatov Institute”, National Research Center, 123182 Moscow (Russian Federation); Malyshkin, Yury, E-mail: malyshkin@fias.uni-frankfurt.de [Frankfurt Institute for Advanced Studies, J.-W. Goethe University, 60438 Frankfurt am Main (Germany); Institute for Nuclear Research, Russian Academy of Sciences, 117312 Moscow (Russian Federation); Pshenichnov, Igor, E-mail: pshenich@fias.uni-frankfurt.de [Frankfurt Institute for Advanced Studies, J.-W. Goethe University, 60438 Frankfurt am Main (Germany); Institute for Nuclear Research, Russian Academy of Sciences, 117312 Moscow (Russian Federation); Greiner, Walter [Frankfurt Institute for Advanced Studies, J.-W. Goethe University, 60438 Frankfurt am Main (Germany)

2015-04-15

A possibility of synthesizing neutron-rich superheavy elements in spallation targets of Accelerator Driven Systems (ADS) is considered. A dedicated software called Nuclide Composition Dynamics (NuCoD) was developed to model the evolution of isotope composition in the targets during a long-time irradiation by intense proton and deuteron beams. Simulation results show that transuranic elements up to {sup 249}Bk can be produced in multiple neutron capture reactions in macroscopic quantities. However, the neutron flux achievable in a spallation target is still insufficient to overcome the so-called fermium gap. Further optimization of the target design, in particular, by including moderating material and covering it by a reflector could turn ADS into an alternative source of transuranic elements in addition to nuclear fission reactors.

TRUPACT-II 157 Examination Report

International Nuclear Information System (INIS)

Barry H. O'Brien; Jeffrey M. Lacy; Kip E. Archibald

2003-01-01

This report presents the results of examination and recovery activities performed on the TRUPACT-II 157 shipping container. The container was part of a contact-handled transuranic waste shipment being transported on a truck to the Waste Isolation Pilot Plant in New Mexico when an accident occurred. Although the transport vehicle sustained only minor damage, airborne transuranic contamination was detected in air samples extracted from inside TRUPACT-II 157 at the Waste Isolation Pilot Plant. Consequently, the shipping container was rejected, resealed, and returned to the Idaho National Engineering and Environmental Laboratory where the payload was disassembled, examined, and recovered for subsequent reshipment to the Waste Isolation Pilot Plant. This report documents the results of those activities

TRUPACT-II 157 Examination Report

Energy Technology Data Exchange (ETDEWEB)

Barry H. O& #39; Brien; Jeffrey M. Lacy; Kip E. Archibald

2003-12-01

This report presents the results of examination and recovery activities performed on the TRUPACT-II 157 shipping container. The container was part of a contact-handled transuranic waste shipment being transported on a truck to the Waste Isolation Pilot Plant in New Mexico when an accident occurred. Although the transport vehicle sustained only minor damage, airborne transuranic contamination was detected in air samples extracted from inside TRUPACT-II 157 at the Waste Isolation Pilot Plant. Consequently, the shipping container was rejected, resealed, and returned to the Idaho National Engineering and Environmental Laboratory where the payload was disassembled, examined, and recovered for subsequent reshipment to the Waste Isolation Pilot Plant. This report documents the results of those activities.

Systems Engineering in the Development and Implementation of the Savannah River Site Transuranic Waste Disposition Program

International Nuclear Information System (INIS)

Fayfich, R.R.

1999-01-01

The use of systems engineering facilitated the strategic planning and implementation of the Savannah River Site (SRS) transuranic waste disposal program. This application represented the first SRS use of systems engineering in the pre-program planning stages during the development of a comprehensive strategic plan for the disposal of transuranic waste at the Department of Energy Waste Isolation Pilot Plant (WIPP) in Carlsbad, New Mexico. The use of systems engineering focused the efforts of the technical experts to devise a three initiative plan for the disposal of transuranic waste where previous efforts failed. Continued application of systems engineering facilitated the further development and implementation of the first initiative outlined in the strategic plan, i.e., set-up the program and process to begin to characterize and ship waste to the WIPP.This application of systems engineering to the transuranic waste program represented the first opportunity at the SRS for a comprehensive usage of systems engineering at all program levels. The application was initiated at the earliest possible point in the program development, i.e., strategic planning, and successively was used in detailed development and implementation of the program. Systems engineering successfully focused efforts to produce a comprehensive plan for the disposal of SRS transuranic waste at the WIPP, and facilitated development of the SRS capability and infrastructure to characterize, certify, and ship waste

Radiological implications of contact maintenance: Impacts on facility design

International Nuclear Information System (INIS)

Brown, R.C.

1994-01-01

The purpose of this document is to provide an initial, rough order of magnitude, evaluation of the relationship between the concentrations of selected radionuclides in process streams of a chemical process plant and the required degree of protective features for plant operations personnel. The evaluation provided in this document specifies ''trigger level'' concentrations of 90 Sr, 137 Cs, and transuranics (TRU) for ''contact maintenance'' activities. Concentrations above the ''trigger levels'' can be accommodated provided offsetting design features are incorporated (e.g., improved shielding partial to total confinement, etc.). This information will assist in defining the degree of reduction of concentrations of radionuclides required for the feed used in a low-level liquid waste processing plant to utilize a contact maintenance design concept. Offsetting design features that influence maintenance personnel exposures in a contact maintenance situation are identified. All concentrations are expressed in terms of actual process fluids before any flushing and decontamination steps

Deposition, translocation and effects of transuranic particles inhaled by experimental animals

International Nuclear Information System (INIS)

Craig, D.K.; Ballou, J.E.; Dagle, G.E.; Mahlum, D.D.; Park, J.F.; Sanders, C.L.; Sikov, M.R.; Stuart, B.O.

1977-01-01

Inhalation exposure constitutes the most likely route of entrance for transuranics into the body. Cancer is the most likely consequence of exposure, but several thousand workers have been exposed during the last 30 yrs without, so far, evidence of exposure-related effects. Several soluble and insoluble transuranic compounds have been studied in rodents and dogs, either alone or combined with exposure to other materials (e.g., PuO/sub 2/--UO/sub 2/ fuel and Na). These studies have provided a wide variety of spatial and temporal dose distribution patterns in the lung. The distribution and total initial deposition in the respiratory tract is a function of the physical characteristics of the inhaled aerosols (size distribution, shape, hygroscopicity) and of the morphology and physiology of the animal. Translocation rates, organ and tissue distribution and excretion in urine and feces, are a function of the physicochemical characteristics of the deposited material (solubility, specific activity, chemical compound, etc.). Differences in rate of translocation of the solubilized material, primarily to the liver and bone, determines the radiation dose to the various tissues involved. Insoluble particles of plutonium dioxide are transferred to the thoracic lymph nodes, which may be functionally destroyed as a consequence. Radiation pneumonitis and pulmonary fibrosis are the main causes of death in animals with cumulative radiation doses to the lung of a few thousand rads. The most significant long-term effect of inhaled transuranic compounds in animals is the development of lung and bone tumors. The main type of lung tumor in both dog and rat is the bronchioloalveolar carcinoma (adenocarcinoma). However, tumor type is a function of radiation dose and dose-distribution at high doses. Bone ranks next to lung as the tissue developing the most tumors following inhalation of transuranics

Deposition, translocation, and effects of transuranic particles inhaled by experimental animals

International Nuclear Information System (INIS)

Craig, D.K.; Ballou, J.E.; Dagle, G.E.; Mahlum, D.D.; Park, J.F.; Sanders, C.L.; Sikov, M.R.; Stuart, B.O.

1977-01-01

Inhalation exposure constitutes the most likely route of entrance for transuranics into the body. Cancer is the most likely consequence of exposure, but several thousand workers have been exposed during the last 30 yrs without, so far, evidence of exposure-related effects. Several soluble and insoluble transuranic compounds have been studied in rodents and dogs, either alone or combined with exposure to other materials (e.g., PuO 2 --UO 2 fuel and Na). These studies have provided a wide variety of spatial and temporal dose distribution patterns in the lung. The distribution and total initial deposition in the respiratory tract is a function of the physical characteristics of the inhaled aerosols (size distribution, shape, hygroscopicity) and of the morphology and physiology of the animal. Translocation rates, organ and tissue distribution and excretion in urine and feces, are a function of the physicochemical characteristics of the deposited material (solubility, specific activity, chemical compound, etc.). Differences in rate of translocation of the solubilized material, primarily to the liver and bone, determines the radiation dose to the various tissues involved. Insoluble particles of plutonium dioxide are transferred to the thoracic lymph nodes, which may be functionally destroyed as a consequence. Radiation pneumonitis and pulmonary fibrosis are the main causes of death in animals with cumulative radiation doses to the lung of a few thousand rads. The most significant long-term effect of inhaled transuranic compounds in animals is the development of lung and bone tumors. The main type of lung tumor in both dog and rat is the bronchioloalveolar carcinoma (adenocarcinoma). However, tumor type is a function of radiation dose and dose-distribution at high doses. Bone ranks next to lung as the tissue developing the most tumors following inhalation of transuranics

Long-lived legacy: Managing high-level and transuranic waste at the DOE Nuclear Weapons Complex. Background paper

International Nuclear Information System (INIS)

1991-05-01

The document focuses on high-level and transuranic waste at the DOE nuclear weapons complex. Reviews some of the critical areas and aspects of the DOE waste problem in order to provide data and further analysis of important issues. Partial contents, High-Level Waste Management at the DOE Weapons Complex, are as follows: High-Level Waste Management: Present and Planned; Amount and Distribution; Current and Potential Problems; Vitrification; Calcination; Alternative Waste Forms for the Idaho National Engineering Laboratory; Technologies for Pretreatment of High-Level Waste; Waste Minimization; Regulatory Framework; Definition of High-Level Waste; Repository Delays and Contingency Planning; Urgency of High-Level Tank Waste Treatment; Technologies for High-Level Waste Treatment; Rethinking the Waste Form and Package; Waste Form for the Idaho National Engineering Laboratory; Releases to the Atmosphere; Future of the PUREX Plant at Hanford; Waste Minimization; Tritium Production; International Cooperation; Scenarios for Future HLW Production. Partial contents of Chapter 2, Managing Transuranic Waste at the DOE Nuclear Weapons Complex, are as follows: Transuranic Waste at Department of Energy Sites; Amount and Distribution; Waste Management: Present and Planned; Current and Potential Problems; Three Technologies for Treating Retrievably Stored Transuranic Waste; In Situ Vitrification; The Applied Research, Development, Demonstration, Testing, and Evaluation Plan (RDDT ampersand E); Actinide Conversion (Transmutation); Waste Minimization; The Regulatory Framework; Definition of, and Standards for, Disposal of Transuranic Waste; Repository Delays; Alternative Storage and Disposal Strategies; Remediation of Buried Waste; The Waste Isolation Pilot Plant; Waste Minimization; Scenarios for Future Transuranic Waste Production; Conditions of No-Migration Determination

Study of the association between exposure to transuranic radionuclides and cancer death

Science.gov (United States)

Fallahian, Naz Afarin

An exploratory epidemiological study has been conducted on 319 deceased nuclear workers, who had recorded intakes and histories of employment for at least one year during the time period from 1943 to 1995, at different facilities including the United States Department of Energy (DOE) sites, and thorium and uranium mining and milling plants. These workers voluntarily agreed to donate their organs or whole body to the United States Transuranium and Uranium Registries (USTUR) for scientific research purposes. The majority of this population was involved in documented radiological incidents during their careers. Many were exposed to transuranic radionuclides primarily via inhalation or puncture wounds. The purpose of this study was to find the level of dose that was received by the USTUR registrants following accidents and subsequent to mitigating actions, and to investigate whether or not there is any association between exposure to these transuranic radionuclides and cancer deaths. The external and internal dose assessments were performed using occupational radiation exposure histories and postmortem concentrations of transuranic radionuclides in critical organs, respectively. Statistical data analyses were performed to identify whether or not the USTUR registrants can be categorized as a 'low-dose' population and to investigate the potential correlation between exposure to transuranic radionuclides and causes of death within this population due to cancers of the lungs and liver as well as cancers of all sites, while controlling for the effects of other confounders. Based on the statistical tests performed, the USTUR registrants can be categorized as a low-dose population in terms of their occupational external exposures. However, when considering their total effective dose equivalents from both external penetrating radiation and internal exposure to transuranic radionuclides, they can not be categorized as a low-dose population with a 95% confidence level (alpha = 0

Characteristics of transuranic waste at Department of Energy sites

International Nuclear Information System (INIS)

Jensen, R.T.; Wilkinson, F.J. III.

1983-05-01

This document reports data and information on TRU waste from all DOE generating and storage sites. The geographical location of the sites is shown graphically. There are four major sections in this document. The first three cover the TRU waste groups known as Newly Generated, Stored, and Buried Wastes. Subsections are included under Newly Generated and Stored on contact-handled and remote-handled waste. These classifications of waste are defined, and the current or expected totals of each are given. Figure 1.3 shows the total amount of Buried and Stored TRU waste. Preparation of this document began in 1981, and most of the data are as of December 31, 1980. In a few cases data were reported to December 31, 1981, and these have been noted. The projections in the Newly Generated section were made, for the most part, at the end of 1981

Mobile loading transuranic waste at small quantity sites in the Department of Energy complex-10523

International Nuclear Information System (INIS)

Carter, Mitch; Howard, Bryan; Weyerman, Wade; Mctaggart, Jerri

2009-01-01

Los Alamos National Laboratory, Carlsbad Office (LANL-CO), operates mobile loading operations for all of the large and small quantity transuranic (TRU) waste sites in the Department of Energy (DOE) complex. The mobile loading team performs loading and unloading evolutions for both contact handled (CH) and remote handled (RH) waste. For small quantity sites, many of which have yet to remove their TRU waste, the mobile loading team will load shipments that will ship to Idaho National Laboratory, a centralization site, or ship directly to the Waste Isolation Pilot Plant (WIPP). For example, Argonne National Laboratory and General Electric Vallecitos Nuclear Center have certified programs for RH waste so they will ship their RH waste directly to WIPP. Many of the other sites will ship their waste to Idaho for characterization and certification. The Mobile Loading Units (MLU) contain all of the necessary equipment needed to load CH and RH waste into the appropriate shipping vessels. Sites are required to provide additional equipment, such as cranes, fork trucks, and office space. The sites are also required to provide personnel to assist in the shipping operations. Each site requires a site visit from the mobile loading team to ensure that all of the necessary site equipment, site requirements and space for shipping can be provided. The mobile loading team works diligently with site representatives to ensure that all safety and regulatory requirements are met. Once the waste is ready and shipping needs are met, the mobile loading team can be scheduled to ship the waste. The CH MLU is designed to support TRUPACT-II and HalfPACT loading activities wherever needed within the DOE complex. The team that performs the mobile loading operation has obtained national certification under DOE for TRUPACT-II and HalfPACT loading and shipment certification. The RH MLU is designed to support removable lid canister (RLC) and RH-72B cask loading activities wherever needed within the DOE

Transuranic Contamination in Sediment and Groundwater at the U.S. DOE Hanford Site

Energy Technology Data Exchange (ETDEWEB)

Cantrell, Kirk J.

2009-08-20

A review of transuranic radionuclide contamination in sediments and groundwater at the DOE’s Hanford Site was conducted. The review focused primarily on plutonium-239/240 and americium-241; however, other transuranic nuclides were discussed as well, including neptunium-237, plutonium-238, and plutonium-241. The scope of the review included liquid process wastes intentionally disposed to constructed waste disposal facilities such as trenches and cribs, burial grounds, and unplanned releases to the ground surface. The review did not include liquid wastes disposed to tanks or solid wastes disposed to burial grounds. It is estimated that over 11,800 Ci of plutonium-239, 28,700 Ci of americium-241, and 55 Ci of neptunium-237 have been disposed as liquid waste to the near surface environment at the Hanford Site. Despite the very large quantities of transuranic contaminants disposed to the vadose zone at Hanford, only minuscule amounts have entered the groundwater. Currently, no wells onsite exceed the DOE derived concentration guide for plutonium-239/240 (30 pCi/L) or any other transuranic contaminant in filtered samples. The DOE derived concentration guide was exceeded by a small fraction in unfiltered samples from one well (299-E28-23) in recent years (35.4 and 40.4 pCi/L in FY 2006). The primary reason that disposal of these large quantities of transuranic radionuclides directly to the vadose zone at the Hanford Site has not resulted in widespread groundwater contamination is that under the typical oxidizing and neutral to slightly alkaline pH conditions of the Hanford vadose zone, transuranic radionuclides (plutonium and americium in particular) have a very low solubility and high affinity for surface adsorption to mineral surfaces common within the Hanford vadose zone. Other important factors are the fact that the vadose zone is typically very thick (hundreds of feet) and the net infiltration rate is very low due to the desert climate. In some cases where

Transuranic waste assay instrumentation: new developments and directions at the Los Alamos Scientific Laboratory

Energy Technology Data Exchange (ETDEWEB)

Close, D.A.; Umbarger, C.J.; West, L.; Smith, W.J.; Cates, M.R.; Noel, B.W.; Honey, F.J.; Franks, L.A.; Pigg, J.L.; Trundle, A.S.

1978-01-01

The Los Alamos Scientific Laboratory is developing assay instrumentation for the quantitative analysis of transuranic materials found in bulk solid wastes generated by Department of Energy facilities and by the commercial nuclear power industry. This also includes wastes generated in the decontamination and decommissioning of facilities and wastes generated during burial ground exhumation. The assay instrumentation will have a detection capability for the transuranics of less than 10 nCi of activity per gram of waste whenever practicable.

Transuranic waste assay instrumentation: new developments and directions at the Los Alamos Scientific Laboratory

International Nuclear Information System (INIS)

Close, D.A.; Umbarger, C.J.; West, L.; Smith, W.J.; Cates, M.R.; Noel, B.W.; Honey, F.J.; Franks, L.A.; Pigg, J.L.; Trundle, A.S.

1978-01-01

The Los Alamos Scientific Laboratory is developing assay instrumentation for the quantitative analysis of transuranic materials found in bulk solid wastes generated by Department of Energy facilities and by the commercial nuclear power industry. This also includes wastes generated in the decontamination and decommissioning of facilities and wastes generated during burial ground exhumation. The assay instrumentation will have a detection capability for the transuranics of less than 10 nCi of activity per gram of waste whenever practicable

In situ grouting of buried transuranic waste with polyacrylamide

International Nuclear Information System (INIS)

Spalding, B.P.; Lee, S.Y.; Farmer, C.D.; Hyder, L.K.; Supaokit, P.

1987-01-01

This project is a demonstration and evaluation of the in situ hydrologic stabilization of buried transuranic waste at a humid site via grout injection. Two small trenches, containing buried transuranic waste, were filled with 34.000 L of polyacrylamide grout. Initial field results have indicated that voids within the trenches were totally filled by the grout and that the intratrench hydraulic conductivity was reduced to below field-measurable values. No evidence of grout constituents were observed in twelve perimeter groundwater monitoring wells indicating that grout was contained completely within the two trenches. Polyacrylamide grout was selected for field demonstration over the polyacrylate grout due to its superior performance in laboratory degradation studies. Also supporting the selection of polyacrylamide was the difficulty in controlling the set time of the acrylate polymerization. Based on preliminary degradation monitoring, the polyacrylamide was estimated to have a microbiological half-life of 362 years in the test soil. 15 refs., 9 figs., 12 tabs

Hanford site implementation plan for buried, transuranic-contaminated waste

International Nuclear Information System (INIS)

1987-05-01

The GAO review of DOE's Defense Waste Management Plan (DWMP) identified deficiencies and provided recommendations. This report responds to the GAO recommendations with regard to the Hanford Site. Since the issuance of the DWMP, an extensive planning base has been developed for all high-level and transuranic waste at the Hanford Site. Thirty-three buried sites have been identified as possibly containing waste that can be classified as transuranic waste. Inventory reports and process flowsheets were used to provide an estimate of the radionuclide and hazardous chemical content of these sites and approximately 370 additional sites that can be classified as low-level waste. A program undertaken to characterize select sites suspected of having TRU waste to refine the inventory estimates. Further development and evaluation are ongoing to determine the appropriate remedial actions, with the objectives of balancing long-term risks with costs and complying with regulations. 18 refs., 7 figs., 6 tabs

In situ grouting of buried transuranic waste with polyacrylamide

Energy Technology Data Exchange (ETDEWEB)

Spalding, B.P.; Lee, S.Y.; Farmer, C.D.; Hyder, L.K.; Supaokit, P.

1987-01-01

This project is a demonstration and evaluation of the in situ hydrologic stabilization of buried transuranic waste at a humid site via grout injection. Two small trenches, containing buried transuranic waste, were filled with 34.000 L of polyacrylamide grout. Initial field results have indicated that voids within the trenches were totally filled by the grout and that the intratrench hydraulic conductivity was reduced to below field-measurable values. No evidence of grout constituents were observed in twelve perimeter groundwater monitoring wells indicating that grout was contained completely within the two trenches. Polyacrylamide grout was selected for field demonstration over the polyacrylate grout due to its superior performance in laboratory degradation studies. Also supporting the selection of polyacrylamide was the difficulty in controlling the set time of the acrylate polymerization. Based on preliminary degradation monitoring, the polyacrylamide was estimated to have a microbiological half-life of 362 years in the test soil. 15 refs., 9 figs., 12 tabs.

Waste management facilities cost information: System cost model product description. Revision 2

International Nuclear Information System (INIS)

Lundeen, A.S.; Hsu, K.M.; Shropshire, D.E.

1996-02-01

In May of 1994, Lockheed Idaho Technologies Company (LITCO) in Idaho Falls, Idaho and subcontractors developed the System Cost Model (SCM) application. The SCM estimates life-cycle costs of the entire US Department of Energy (DOE) complex for designing; constructing; operating; and decommissioning treatment, storage, and disposal (TSD) facilities for mixed low-level, low-level, transuranic, and mixed transuranic waste. The SCM uses parametric cost functions to estimate life-cycle costs for various treatment, storage, and disposal modules which reflect planned and existing facilities at DOE installations. In addition, SCM can model new facilities based on capacity needs over the program life cycle. The SCM also provides transportation costs for DOE wastes. Transportation costs are provided for truck and rail and include transport of contact-handled, remote-handled, and alpha (transuranic) wastes. The user can provide input data (default data is included in the SCM) including the volume and nature of waste to be managed, the time period over which the waste is to be managed, and the configuration of the waste management complex (i.e., where each installation's generated waste will be treated, stored, and disposed). Then the SCM uses parametric cost equations to estimate the costs of pre-operations (designing), construction costs, operation management, and decommissioning these waste management facilities

In situ grouting of buried transuranic waste

International Nuclear Information System (INIS)

Spalding, B.P.; Lee, S.Y.

1987-01-01

This task is a demonstration and evaluation of the in situ hydrologic stabilization of buried transuranic waste at a humid site via grout injection. Two small trenches, containing buried transuranic waste, were filled with 34,000 liters of polyacrylamide grout. Initial field results have indicated that voids within the trenches were totally filled by the grout and that the intratrench hydraulic conductivity was reduced to below field-measurable values. The grout was also completely contained within the two trenches as no grout constituents were observed in the 12 perimeter ground water monitoring wells. Polyacrylamide grout was selected for field demonstration over polyacrylate grout because of its superior performance in laboratory degradation studies. Also supporting the selection of polyacrylamide was the difficulty of controlling the set time of the acrylate polymerization process in the presence of potassium ferricyanide. Based on preliminary degradation monitoring, polyacrylamide was estimated to have a microbiological half-life of 115 years in the test soil. However, this calculated value is likely to be conservatively low because microbial degradation of the grout set accelerator or residual monomer may be contributing most to the measured microbial respiration. Addition work, using 14 C-labeled acrylate and acrylamide grouts, is being carried out to more accurately estimate the grouts' microbiological half-life

Composition containing transuranic elements for use in the homeopathic treatment of aids

International Nuclear Information System (INIS)

Lustig, D.

1996-01-01

A homeopathic remedy consisting of a composition containing one or more transuranic elements, particularly plutonium, for preventing and treating acquired immunodeficiency syndrome (AIDS) in humans, as well as seropositivity for human immunodeficiency virus (HIV). Said composition is characterized in that it uses any chemical or isotopic form of one or more transuranic elements (neptunium, plutonium, americium, curium, berkelium, californium or einsteinium), particularly plutonium, said form being diluted and dynamized according to conventional homeopathic methods, particularly the so-called Hahnemann and Korsakov methods, and provided preferably but not exclusively in the form of lactose and/or saccharose globules or granules impregnated with the active principle of said composition. (author)

Filter testing and development for prolonged transuranic service and waste reduction

International Nuclear Information System (INIS)

Geer, J.A.; Buttedahl, O.I.; Skaats, C.D.; Terada, K.; Woodard, R.W.

1977-02-01

The life of High Efficiency Particulate Air (HEPA) filters used in transuranic service is influenced greatly by the gaseous and particulate matter to which the filters are exposed. The most severe conditions encountered at Rocky Flats are at the ventilation systems serving the plutonium recovery operations in Bldg. 771. A project of filter testing and development for prolonged transuranic service and waste reduction was formally initiated at Rocky Flats on July 1, 1975. The project is directed toward improving filtration methods which will prolong the life of HEPA filter systems without sacrificing effectiveness. Another important aspect of the project is to reduce the volume of HEPA filter waste shipped from the plant for long-term storage. Progress to September 30, 1976, is reported

Chemical form of transuranic elements in underground environment and its effect on adsorption

International Nuclear Information System (INIS)

Tanaka, Tomo

1990-01-01

Many of the transuranic elements such as Np, Pu and Am contained in high-level radioactive wastes are highly dangerous to humans and have extremely long lives. Therefore, safety evaluation of them is highly important after their disposal into the ground. Particularly important processes include the migration of these transuranic elements in near and far fields. The migration of a nuclide depends largely on its chemical form in the underground environment. The present report first describes various chemical forms of transuranic elements in underground environments and outlines their migration behaviors. Techniques that have recently become available for determining their chemical forms include photo-acoustic spectroscopy, thermal lensing spectroscopy, laser induced fluorescence, photo-acoustic detection of light scattering, auto-correlation photon spectroscopy, and laser-induced time-resolved spectrofluorometry. Chemical forms of these elements are then discussed focusing on underground environmental conditions, pH-Eh diagram, deposition/dissolution, formation of complex, formation of colloid, and organic complexes. Migration is discussed in relation to ions, insoluble matters, and colloids. (N.K.)

Operational and engineering developments in the management of low-level radioactive waste at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Kendall, E.W.; McKinney, J.D.; Wehmann, G.

1979-01-01

The Radioactive Waste Management Complex (RWMC) of the Idaho National Engineering Laboratory is a site for shallow land disposal and storage of solid radioactive waste. It is currently operated for ERDA by EG and G Idaho, Inc. The facility has accepted radioactive waste since July 1952. Both transuranic and non-transuranic wastes are handled at the complex. This document describes the operational and engineering developments in waste handling and storage practices that have been developed during the 25 years of waste handling operations. Emphasis is placed on above-ground transuranic waste storage, subsurface transuranic waste retrieval, and beta/gamma compaction disposal. The proposed future programs for the RWMC including a Molten Salt Combustion Facility and Production Scale Retrieval Project are described

Analysis of transuranic isotopes in irradiated U3Si2-Al fuel by alpha spectrometry

International Nuclear Information System (INIS)

Dian Anggraini; Aslina B Ginting; Arif Nugroho

2011-01-01

Separation and analysis of transuranic isotopes (uranium and plutonium) in irradiated U 3 Si 2 -Al plate has been done. The analysis experiment includes sample preparation (i.e. cutting, dissolving, filtering, dilution), fission products separation from heavy elements, and analysis of transuranic isotopes content with alpha spectrometer. The separation of transuranic isotopes (U, Pu) was done by two methods, i.e. direct method and ion exchanger method with zeolite. Measurement of standard transuranic isotope (AMR 43) and standard U 3 O 8 was done in advance in order to determine percentage of 235 U recovery and detector efficiency. Recovery of 235 U isotope was obtained as much as 92,58%, which fulfills validation requirement, and the detector efficiency was 0.314. Based on the measured recovery and detector efficiency, the separation was done by direct electrodeposition method of 250 µL irradiated U 3 Si 2 -Al solution. The deposited sample was subsequently analyzed with alpha spectrometer. The separation with ion exchanger was done by mixing and shaking of 300 µL irradiated U 3 Si 2 -Al solution and 0.5 gram zeolite to separate the liquid phase from the solid phase. The liquid phase was electrodeposited and analyzed with alpha spectrometer. The analysis of transuranic isotopes (U, Pu) by both methods shows different results. Heavy element ( 238 U, 236 U, 234 U, 239 Pu) content obtained by direct method was 0.0525 g/g and 235 U= 0.0076 g/g, while the separation using zeolite ion exchanger resulted in Heavy element = 0.0253 g/g and 235 U = 0.0092 g/g. (author)

Sampling of soils for transuranic nuclides: a review

International Nuclear Information System (INIS)

Fowler, E.B.; Essington, E.H.

1977-01-01

A review of the literature pertinent to the sampling of soils for radionuclides is presented; emphasis is placed on transuranic nuclides. Sampling of soils is discussed relative to systems of heterogeneous distributions and varied particle sizes encountered in certain environments. Sampling methods that have been used for two different sources of contamination, global fallout, and accidental or operational releases, are included

Development of a room air monitor system and workplace transuranic aerosol measurement system

International Nuclear Information System (INIS)

Tyree, W.H.; Balmer, D.K.

1987-01-01

A room air monitor under development at Rocky Flats will detect transuranic aerosols with improved sample collection and alpha particle counting efficiencies. The new instrument will be integrated into present building sampling systems replacing older commercial units now in service. The collection filter medium has been designed to simplify handling and identification procedures. Operating parameters for the system include a sampling rate of 50 liters per minute, with a counting geometry of at least twenty percent. Projected sensitivity is about 0.3 MPC-day. Estimated cost is $2,000.00 for a sampling head with a 1700mm 2 are ion-impacted detector, filter holder and package. This cost includes the electronics counting system with local alarms and battery backup. The sampling head will be produced in quantity as an aluminum casting. A front panel liquid crystal display scalar will indicate the net count obtained from long-lived emitters in the presence of radon interference. The unit includes the option of plug-in high-power audio and visual alarm outputs. A working prototype will be available for inspection and evaluation at the October Workshop. 6 figures, 1 table

Shipment and Disposal of Solidified Organic Waste (Waste Type IV) to the Waste Isolation Pilot Plant (WIPP)

International Nuclear Information System (INIS)

D'Amico, E. L; Edmiston, D. R.; O'Leary, G. A.; Rivera, M. A.; Steward, D. M.

2006-01-01

In April of 2005, the last shipment of transuranic (TRU) waste from the Rocky Flats Environmental Technology Site to the WIPP was completed. With the completion of this shipment, all transuranic waste generated and stored at Rocky Flats was successfully removed from the site and shipped to and disposed of at the WIPP. Some of the last waste to be shipped and disposed of at the WIPP was waste consisting of solidified organic liquids that is identified as Waste Type IV in the Contact-Handled Transuranic Waste Authorized Methods for Payload Control (CH-TRAMPAC) document. Waste Type IV waste typically has a composition, and associated characteristics, that make it significantly more difficult to ship and dispose of than other Waste Types, especially with respect to gas generation. This paper provides an overview of the experience gained at Rocky Flats for management, transportation and disposal of Type IV waste at WIPP, particularly with respect to gas generation testing. (authors)

Management of transuranics using the Integral Fast Reactor (IFR) fuel cycle

International Nuclear Information System (INIS)

Wade, D.C.

1994-01-01

The 50 years of activities following the discovery of self-sustaining fission chains have given rise to a buildup of roughly 900 tons of manmade transuranics. Of the total, about 260 tons of Pu 239 were generated for use in weapons while the remainder were generated as a byproduct of electrical power produced worldwide by the commercial thermal nuclear power industry. What is to be done with these actinides? The options for disposition include interminable storage, burial, or recycle for use. The pros and cons of each option are being vigorously debated regarding the impact upon the issues of human and ecological risk -- both current and future; weapons proliferation potential -- both current and future; and total life cycle benefits and costs. As to the options for utilization, commercial uses for actinides (uranium and transuranics) are of limited diversity. The actinides have in the past and will in the future find application in large scale mostly by virtue of their ability to release energy through fission, and here their utility is unmatched -- whether the application be in commercial electricity generation or in armaments. The integral Fast Reactor (IFR) fuel cycle offers a number of features for management of the current and future burden of manmade transuranic materials and for capturing the energy content of the U 238 . These features are discussed here

Long-range plan for buried transuranic waste studies at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Berreth, P.D.; Fischer, D.K.; Suckel, R.A.

1984-11-01

This document presents a plan to perform detailed studies of alternatives considered for the long-term management of buried transuranic waste at the INEL. The studies will provide the technical basis for DOE to make a decision on the future management of that waste. Although the waste is currently being handled in an acceptable manner, new solutions are continually being researched to improve handling techniques. Three alternatives are being considered: (a) leave the waste as is; (b) improve in situ confinement of the waste; (c) retrieve, process, and certify the waste for disposal at a federal repository. Fifteen studies are described in this plan for the latter two alternatives. The leave-as-is alternative involves continuing present procedures for managing the buried waste. An ongoing environmental surveillance program, a low-level-waste stabilization program, and enhanced subsurface migration studies begun in FY-1984 at the INEL will provide data for the decision-making process for INEL buried TRU waste. These ongoing studies for the leave-as-is alternative are summarized in this plan in limited detail. The improved-confinement alternative involves leaving the waste in place, but providing additional protection against wind water penetration, erosion, and plant and animal intrusion. Several studies proposed will examine special techniques to immobilize or encapsulate the buried waste. Studies of the third alternative will investigate improved retrieval, processing and certification techniques. New equipment, such as industrial manipulators and excavating machinery, will be tested in the retrieval studies. Processing and certification studies will examine rapidly changing or new technologies. 19 references, 8 figures, 4 tables

Decontamination of transuranic contaminated metals by melt refining

International Nuclear Information System (INIS)

Heshmatpour, B.; Copeland, G.L.; Heestand, R.L.

1983-01-01

Melt refining of transuranic contaminated metals is a possible decontamination process with the potential advantages of producing metal for reuse and of simplifying chemical analyses. By routinely achieving the 10 nCi/g( about0.1ppm) level by melt refining, scrap metal can be removed from the transuranic waste category. (To demonstrate the effectiveness of this melt refining process, mild steel, stainless steel, nickel, and copper were contaminated with 500 ppm (μg/g) PuO 2 and melted with various fluxes. The solidified slags and metals were analyzed for their plutonium contents, and corresponding partition ratios for plutonium were calculated. Some metals were double refined in order to study the effect of secondary slag treatment. The initial weight of the slags was also varied to investigate the effect of slag weight on the degree of plutonium removal. In general, all four metals could be decontaminated below 1 ppm (μg/g) Pu ( about100 nCi/g) by a single slag treatment. Doubling the slag weight did not improve decontamination significantly; however, double slag treatment using 5 wt.% slag did decontaminate the metals to below 0.1 ppm (μg/g) Pu (10 nCi/g).)

Establishment of a Cost-Effective and Robust Planning Basis for the Processing of M-91 Waste at the Hanford Site

International Nuclear Information System (INIS)

Johnson, Wayne L.; Parker, Brian M.

2004-01-01

This report identifies and evaluates viable alternatives for the accelerated processing of Hanford Site transuranic (TRU) and mixed low-level wastes (MLLW) that cannot be processed using existing site capabilities. Accelerated processing of these waste streams will lead to earlier reduction of risk and considerable life-cycle cost savings. The processing need is to handle both oversized MLLW and TRU containers as well as containers with surface contact dose rates greater than 200 mrem/hr. This capability is known as the ''M-91'' processing capability required by the Tri-Party Agreement milestone M-91--01. The new, phased approach proposed in this evaluation would use a combination of existing and planned processing capabilities to treat and more easily manage contact-handled waste streams first and would provide for earlier processing of these wastes

COMPLETION OF THE TRANSURANIC GREATER CONFINEMENT DISPOSAL BOREHOLE PERFORMANCE ASSESSMENT FOR THE NEVADA TEST SITE

International Nuclear Information System (INIS)

Colarusso, Angela; Crowe, Bruce; Cochran, John R.

2003-01-01

Classified transuranic material that cannot be shipped to the Waste Isolation Pilot Plant in New Mexico is stored in Greater Confinement Disposal boreholes in the Area 5 Radioactive Waste Management Site on the Nevada Test Site. A performance assessment was completed for the transuranic inventory in the boreholes and submitted to the Transuranic Waste Disposal Federal Review Group. The performance assessment was prepared by Sandia National Laboratories on behalf of the U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office using an iterative methodology that assessed radiological releases from the intermediate depth disposal configuration against the regulatory requirements of the 1985 version of 40 CFR 191 of the U.S. Environmental Protection Agency. The transuranic materials are stored at 21 to 37 m depth (70 to 120 ft) in large diameter boreholes constructed in the unsaturated alluvial deposits of Frenchman Flat. Hydrologic processes that affect long- term isolation of the radionuclides are dominated by extremely slow upward rates of liquid/vapor advection and diffusion; there is no downward pathway under current climatic conditions and there is no recharge to groundwater under future ''glacial'' climatic conditions. A Federal Review Team appointed by the Transuranic Waste Disposal Federal Review Group reviewed the Greater Confinement Disposal performance assessment and found that the site met the majority of the regulatory criteria of the 1985 and portions of the 1993 versions of 40 CFR 191. A number of technical and procedural issues required development of supplemental information that was incorporated into a final revision of the performance assessment. These issues include inclusion of radiological releases into the complementary cumulative distribution function for the containment requirements associated with drill cuttings from inadvertent human intrusion, verification of mathematical models used in the performance

Critical evaluation of the limit of transuranic contamination of low level waste

International Nuclear Information System (INIS)

Rodger, W.A.

1976-01-01

The suggested limit for transuranics of 10 nanocuries/gram as a break point at which wastes should go to a national repository is seriously questioned. It is shown that insofar as protection of water supplies is concerned, the key to the problem is $sup 90$Sr, not transuranics, and in any case, the limit should be based on a site-determined inventory, not on concentration. Concentration is only important as a protection for future stumblers who might dig into the waste. Calculations are presented to show that for this purpose the limit should be higher by several orders of magnitude. The 10 nanocurie/gram should be used as a definition of complete innocuousness. 4 refs

Relationship of microbial processes to the fate and behavior of transuranic elements in soils, plants, and animals

International Nuclear Information System (INIS)

Wildung, R.E.; Garland, T.R.

1980-01-01

Soil physicochemical and microbial processes influence the long-term solubility, form, and bioavailability of plutonium and other transuranic elements important in the nuclear fuel cycle. Consideration is given to the chemistry/microbiology of the transuranic elements in soil, emphasizing possible organic complexation reactions in soils and plants and the relationship of these phenomena to gastrointestinal absorption

Application of advanced handling techniques to transportation cask design

International Nuclear Information System (INIS)

Bennett, P.C.

1992-01-01

Sandia National Laboratories supports the US Department of Energy (DOE) Office of Civilian Radioactive Waste Management (OCRWM) applying technology to the safe transport of nuclear waste. Part of that development effort includes investigation of advanced handling technologies for automation of cask operations at nuclear waste receiving facilities. Although low radiation levels are expected near transport cask surfaces, cumulative occupational exposure at a receiving facility can be significant. Remote automated cask handling has the potential to reduce both the occupational exposure and the time necessary to process a cask. Thus, automated handling is consistent with DOE efforts to reduce the lifecycle costs of the waste disposal system and to maintain public and occupational radiological risks as low as reasonably achievable. This paper describes the development of advanced handling laboratory mock-ups and demonstrations for spent fuel casks. Utilizing the control enhancements described below, demonstrations have been carried out including cask location and identification, contact and non-contact surveys, impact limiter removal, tiedown release, uprighting, swing-free movement, gas sampling, and lid removal operations. Manually controlled movement around a cask under off-normal conditions has also been demonstrated

Integration of long-range planning for management of defense transuranic waste

International Nuclear Information System (INIS)

Gilbert, K.V.; McFadden, M.H.; Raudenbush, M.H.; Smith, L.J.

1984-01-01

As described in The Defense Waste Management Plan, the defense TRU program goal is to achieve permanent disposal and to end interim storage. TRU waste is currently stored at six Department of Energy (DOE) sites, and new waste is generated at several more sites. The Waste Isolation Pilot Plant (WIPP) project is well defined, and it has been necessary to integrate the activities of other parts of the TRU program in support of DOE Headquarters policy and the WIPP schedules and technical requirements. The strategy is described in the Defense Transuranic Waste Program Strategy Document. More detailed, quantitative plans have been developed through the use of several system models, with a Long-Range Master Plan for Defense Transuranic Waste Management as the focal point for coordination of proposed plans with all the parties involved

Waste management facilities cost information for transuranic waste

International Nuclear Information System (INIS)

Shropshire, D.; Sherick, M.; Biagi, C.

1995-06-01

This report contains preconceptual designs and planning level life-cycle cost estimates for managing transuranic waste. The report's information on treatment and storage modules can be integrated to develop total life-cycle costs for various waste management options. A procedure to guide the U.S. Department of Energy and its contractor personnel in the use of cost estimation data is also summarized in this report

In situ vitrification: application analysis for stabilization of transuranic waste

International Nuclear Information System (INIS)

Oma, K.H.; Farnsworth, R.K.; Rusin, J.M.

1982-09-01

The in situ vitrification process builds upon the electric melter technology previously developed for high-level waste immobilization. In situ vitrification converts buried wastes and contaminated soil to an extremely durable glass and crystalline waste form by melting the materials, in place, using joule heating. Once the waste materials have been solidified, the high integrity waste form should not cause future ground subsidence. Environmental transport of the waste due to water or wind erosion, and plant or animal intrusion, is minimized. Environmental studies are currently being conducted to determine whether additional stabilization is required for certain in-ground transuranic waste sites. An applications analysis has been performed to identify several in situ vitrification process limitations which may exist at transuranic waste sites. Based on the process limit analysis, in situ vitrification is well suited for solidification of most in-ground transuranic wastes. The process is best suited for liquid disposal sites. A site-specific performance analysis, based on safety, health, environmental, and economic assessments, will be required to determine for which sites in situ vitrification is an acceptable disposal technique. Process economics of in situ vitrification compare favorably with other in-situ solidification processes and are an order of magnitude less than the costs for exhumation and disposal in a repository. Leachability of the vitrified product compares closely with that of Pyrex glass and is significantly better than granite, marble, or bottle glass. Total release to the environment from a vitrified waste site is estimated to be less than 10 -5 parts per year. 32 figures, 30 tables

Dual germanium detector system for the routine assay of low level transuranics in soil

International Nuclear Information System (INIS)

Crowell, J.M.

1980-01-01

As an outgrowth of previous on soil radioassay, we have developed an automated assay system for determining the transuranic radionuclide content of soils, with particular interest in Pu. The system utilizes two commercial planar intrinsic germanium detectors in opposition. The large area of the detectors (2100 mm 2 ) and the thinness of the detector crystals (7 mm) permit sensitive analysis of the L x ray emission region of the transuranics (13 to 21 keV). With counting times of 5 hours, we obtain detection limits of 241 Am

Quantities of transuranic elements in the environment from operations relating to nuclear weapons

International Nuclear Information System (INIS)

Facer, G.

1980-01-01

Only nuclear explosions near or above the earth's surface or under water have contributed substantial amounts of transuranic materials to the world bioenvironment. The amounts of transuranics placed in the environment through underground test ventings, accidents involving US nuclear weapons, and releases during weapon production operations have been negligible in comparison with those from atmospheric testing of nuclear explosives. On the order of 10 5 Ci of plutonium has been dispersed within our environment from about 400 nuclear explosive tests, including those by the US, Great Britain, and Russia, between 1945 and 1963, plus more recent nuclear explosive tests in the atmosphere by China, India, and France

Projected transuranic waste loads requiring treatment, storage, and disposal

International Nuclear Information System (INIS)

Hong, K.; Kotek, T.

1996-01-01

This paper provides information on the volume of TRU waste loads requiring treatment, storage, and disposal at DOE facilities for three siting configurations. Input consisted of updated inventory and generation data from. Waste Isolation Pilot plant Transuranic Waste Baseline Inventory report. Results indicate that WIPP's design capacity is sufficient for the CH TRU waste found throughout the DOE Complex

Documentation of acceptable knowledge for LANL Plutonium Facility transuranic waste streams

International Nuclear Information System (INIS)

Montoya, A.J.; Gruetzmacher, K.; Foxx, C.; Rogers, P.S.Z.

1998-01-01

Characterization of transuranic waste from the LANL Plutonium Facility for certification and transportation to WIPP includes the use of acceptable knowledge as specified in the WIPP Quality Assurance Program Plan. In accordance with a site-specific procedure, documentation of acceptable knowledge for retrievably stored and currently generated transuranic waste streams is in progress at LANL. A summary overview of the transuranic waste inventory is complete and documented in the Sampling Plan. This document also includes projected waste generation, facility missions, waste generation processes, flow diagrams, times, and material inputs. The second part of acceptable knowledge documentation consists of assembling more detailed acceptable knowledge information into auditable records and is expected to require several years to complete. These records for each waste stream must support final assignment of waste matrix parameters, EPA hazardous waste numbers, and radionuclide characterization. They must also include a determination whether waste streams are defense waste streams for compliance with the WIPP Land Withdrawal Act. The LANL Plutonium Facility's mission is primarily plutonium processing in basic special nuclear material (SNM) research activities to support national defense and energy programs. It currently has about 100 processes ranging from SNM recovery from residues to development of plutonium 238 heat sources for space applications. Its challenge is to characterize and certify waste streams from such diverse and dynamic operations using acceptable knowledge. This paper reports the progress on the certification of the first of these waste streams to the WIPP WAC

Behaviour of transuranic radionuclides in soils, plants and soil-plant system

International Nuclear Information System (INIS)

Vyas, B.N.; Mistry, K.B.

1996-01-01

The present paper reviews the investigations undertaken to elucidate the physicochemical, edaphic and physiological aspects of the behaviour of long-lived transuranic radionuclides 239 Pu and 241 Am in typical Indian soils and soil-plant systems. 23 refs

Language Contact and Bilingualism

NARCIS (Netherlands)

Appel, René; Muysken, Pieter

2006-01-01

What happens - sociologically, linguistically, educationally, politically - when more than one language is in regular use in a community? How do speakers handle these languages simultaneously, and what influence does this language contact have on the languages involved? Although most people in the

Interactions of marine plankton with transuranic elements. II

International Nuclear Information System (INIS)

Fisher, N.S.; Bjerregaard, P.; Huynh-Ngoc, L.; Harvey, G.R.

1983-01-01

To assess the significance of naturally occurring dissolved organic matter (DOM) on complexation of transuranic elements in seawater, a series of bioassay experiments was conducted in which the effect of DOM on the accumulation of 241 Am, 237 Pu(III-IV), and 237 Pu(V-VI) by the marine diatom Thalassiosira pseudonana was measured. EDTA at 0.3 μM complexed both metals substantially, resulting in reduced radio-isotope uptake by the diatom; the greatest effect was on Pu(III-IV). In contrast, there was no apparent complexation of either element by equimolar concentrations of marine fulvic (MFA) or humic acids (MHA), naturally occurring photooxidizable DOM (uncharacterized), or diatom exudates, as none of these materials reduced isotope uptake; on the contrary, there were indications that some of this DOM enhanced transuranic bioaccumulation in the diatom slightly. Subsequent experiments showed this enhancement was probably due to complexation of transition metals by the DOM, leading to fewer ambient ions 'competing' for binding sites on the cells; 241 Am uptake rates were negatively correlated (r = -0.846, P<.01) with ΣASV-labile Cu + Zn + Cd + Pb. These experiments suggest that naturally occurring DOM may not appreciably complex Am or Pu or greatly affect their bioavailability in the sea. (Auth.)

Hydrothermal processing of transuranic contaminated combustible waste

International Nuclear Information System (INIS)

Buelow, S.J.; Worl, L.; Harradine, D.; Padilla, D.; McInroy, R.

2001-01-01

Experiments at Los Alamos National Laboratory have demonstrated the usefulness of hydrothermal processing for the disposal of a wide variety of transuranic contaminated combustible wastes. This paper provides an overview of the implementation and performance of hydrothermal treatment for concentrated salt solutions, explosives, propellants, organic solvents, halogenated solvents, and laboratory trash, such as paper and plastics. Reaction conditions vary from near ambient temperatures and pressure to over 1000degC and 100 MPa pressure. Studies involving both radioactive and non-radioactive waste simulants are discussed. (author)

Continued oversight of the Waste Isolation Pilot Plant

International Nuclear Information System (INIS)

Peake, R. Thomas

2014-01-01

safety considerations. Contact-handled (CH) waste is defined by a container surface dose rate of less than 2 mSv/hr (200 mrem/hr) while remote-handled waste has a surface dose rate of greater than 2 mSv/hr. The contact-handled waste is disposed of in containers placed on the floor of the repository. Figure 2 shows some emplaced contact-handled waste. The statute limits the total activity of remote-handled (RH) waste to ∼1.9 x 10 17 Bq (5 100 000 Ci). RH waste is currently placed in holes bored into the waste room walls, but EPA has approved DOE plans to allow the RH waste to be placed in shielded containers (drums) that will reduce the dose rate to less than 2 mSv/hr, allowing the waste to be managed as CH waste. Although shielded containers are significantly heavier than the standard containers, this strategy allows DOE the option of placing some of the RH waste on the floor, supplementing the more limited volume that can be emplaced in the walls. In summary, the initial certification of the WIPP required an extensive effort. The five-year re-certification process is similar but is less intense with fewer issues, and the site developer still has to develop high quality information. The site developer can focus on those areas that have changed, and there will be further changes during the operational period of the facility. One advantage of the re-certifications is that both the site developer and regulator can build upon the existing knowledge base instead of dealing with everything as a new issue; however, staff turnover brings challenges to maintaining the knowledge base. (authors)

Hand hygiene prior to contact lens handling is problematical.

Science.gov (United States)

McMonnies, Charles W

2012-04-01

To establish guidelines for contact lens wearers' hand hygiene practices which achieve a balance between minimising risk of infection and reasonable expectations on the ability of patients to follow them. Evidence has been obtained from publications via PubMed, Advanced Medline Search, Cochrane Reviews, Google Scholar and using the key words hand hygiene, washing and contact lens. Guidelines for effective hand washing and the bother involved vary according to the level of hygiene required. High levels of non-compliance with hand hygiene practices, even among healthcare workers, gives an indication of how important the level of bother involved when following guidelines can be in contributing to non-compliance. Better patient education to improve hand washing techniques as well as patient attitudes toward hand hygiene are needed to reduce high non-compliance levels. Better hand hygiene techniques and higher frequency of their application give the prospect of reduced risk of infection and of any discomfort that arises from increased lens and ocular bioburden. In order that adoption rates might be maximised, the guidelines which have been distilled from this review attempt to strike a balance between technique redundancy and the associated higher levels of hygiene achieved and the possibility that the perception of too much bother involved could reduce participation rates. The guidelines have been expanded by the inclusion of suggested explanatory information in the expectation that helping patients to understand why the recommendations are made will have the effect of increasing their adoption. Copyright © 2011 British Contact Lens Association. Published by Elsevier Ltd. All rights reserved.

Waste management facilities cost information for transportation of radioactive and hazardous materials

Energy Technology Data Exchange (ETDEWEB)

Feizollahi, F.; Shropshire, D.; Burton, D.

1995-06-01

This report contains cost information on the U.S. Department of Energy (DOE) Complex waste streams that will be addressed by DOE in the programmatic environmental impact statement (PEIS) project. It describes the results of the task commissioned by DOE to develop cost information for transportation of radioactive and hazardous waste. It contains transportation costs for most types of DOE waste streams: low-level waste (LLW), mixed low-level waste (MLLW), alpha LLW and alpha MLLW, Greater-Than-Class C (GTCC) LLW and DOE equivalent waste, transuranic (TRU) waste, spent nuclear fuel (SNF), and hazardous waste. Unit rates for transportation of contact-handled (<200 mrem/hr contact dose) and remote-handled (>200 mrem/hr contact dose) radioactive waste are estimated. Land transportation of radioactive and hazardous waste is subject to regulations promulgated by DOE, the U.S. Department of Transportation (DOT), the U.S. Nuclear Regulatory Commission (NRC), and state and local agencies. The cost estimates in this report assume compliance with applicable regulations.

Ecological effects of transuranics in the terrestrial environment

International Nuclear Information System (INIS)

Whicker, F.W.

1980-01-01

This chapter explores the ecological effects of transuranium radionuclides in terrestrial environments. No direct studies that relate the level of transuranic contamination to specific changes in structure or function of ecological systems have been carried out. The only alternative approach presently available is to infer such relationships from observations of biota in contaminated environments and models. Advantages and shortcomings of these observations as well as those of the direct experimental approach are discussed

Contact-free handling using actively controlled electrostatic levitating fields

NARCIS (Netherlands)

Woo, S.J.

2012-01-01

In general electric field forces have the distinctive property of being able to mediate forces to virtually any material in a fully non-invasive and contact-free fashion. Based on this property, electrostatic levitation holds great promise for the semiconductor, solar panel, and flat-panel display

In-Situ Assay Of Transuranic Radionuclides In The Vadose Zone Using High-Resolution Spectral Gamma Logging - A Hanford Case Study

International Nuclear Information System (INIS)

Rohay, V.J.; Henwood, P.; McCain, R.

2009-01-01

High-resolution spectral gamma logging in steel-cased boreholes is used to detect and quantify transuranic radionuclides in the subsurface. Pu-239, Pu-241, Am-241, and Np-237 are identified based on characteristic decay gammas. Typical minimum detectable levels are on the order of 20 to 40 nCi/g. In intervals of high transuranic concentrations, gamma rays from other sources may complicate analysis and interpretation. Gamma rays detected in the borehole may originate from three sources: decay of the parent transuranic radionuclide or a daughter; alpha interactions; and interactions with neutrons resulting from either spontaneous fission or alpha particle interactions.

Influence of non-radioactive payload parameters on radioactive shipping packages

International Nuclear Information System (INIS)

Drez, P.E.; Murthy, D.V.S.; Temus, C.J.; Quinn, G.J.; Ozaki, C.

1989-01-01

The transport of radioactive waste materials in radioactive material (RAM) packages involves two components: the packaging used for transportation, and the waste which forms the payload. The payload is usually comprised of non-radioactive materials contaminated with radionuclides. The non-radionuclide payload characteristics can often be a controlling factor in determining the restrictions imposed on the certification of the package. This paper describes these package/payload interactions and the limiting parameters for the Transuranic Package Transporter-II (TRUPACT-II), designed for the transportation of Contact Handled Transuranic (CH-TRU) waste. The parameters discussed include the physical and chemical form of the payload, the configuration of the waste, and resulting gas generation and gas release phenomena. Brief descriptions of the TRUPACT-II package and its payload are presented initially

Establishment of a Cost-Effective and Robust Planning Basis for the Processing of M-91 Waste at the Hanford Site

Energy Technology Data Exchange (ETDEWEB)

Johnson, Wayne L.; Parker, Brian M.

2004-07-30

This report identifies and evaluates viable alternatives for the accelerated processing of Hanford Site transuranic (TRU) and mixed low-level wastes (MLLW) that cannot be processed using existing site capabilities. Accelerated processing of these waste streams will lead to earlier reduction of risk and considerable life-cycle cost savings. The processing need is to handle both oversized MLLW and TRU containers as well as containers with surface contact dose rates greater than 200 mrem/hr. This capability is known as the ''M-91'' processing capability required by the Tri-Party Agreement milestone M-91--01. The new, phased approach proposed in this evaluation would use a combination of existing and planned processing capabilities to treat and more easily manage contact-handled waste streams first and would provide for earlier processing of these wastes.

Statistics and sampling in transuranic studies

International Nuclear Information System (INIS)

Eberhardt, L.L.; Gilbert, R.O.

1980-01-01

The existing data on transuranics in the environment exhibit a remarkably high variability from sample to sample (coefficients of variation of 100% or greater). This chapter stresses the necessity of adequate sample size and suggests various ways to increase sampling efficiency. Objectives in sampling are regarded as being of great importance in making decisions as to sampling methodology. Four different classes of sampling methods are described: (1) descriptive sampling, (2) sampling for spatial pattern, (3) analytical sampling, and (4) sampling for modeling. A number of research needs are identified in the various sampling categories along with several problems that appear to be common to two or more such areas

Making transuranic assay measurements using modern controllers

International Nuclear Information System (INIS)

Kuckertz, T.H.; Caldwell, J.T.; Medvick, P.A.; Kunz, W.E.; Hastings, R.D.

1987-01-01

This paper describes methodology and computer-controlled instrumentation developed at the Los Alamos National Laboratory that accurately performs nondestructive assays of large containers bearing transuranic wastes and nonradioactive matrix materials. These assay systems can measure fissile isotopes with 1-mg sensitivity and spontaneous neutron-emitting isotopes at a 10-mg sensitivity. The assays are performed by neutron interrogation, detection, and counting in a custom assay chamber. An International Business Machines Personal Computer (IBM-PC) is used to control the CAMAC-based instrumentation system that acquires the assay data. 6 refs., 7 figs

Rigid Bodies in Contact

DEFF Research Database (Denmark)

Niebe, Sarah Maria

. A contact point determination method, based on boolean surface maps, is developed to handle collisions between tetrahedral meshes. The novel nonsmooth nonlinear conjugate gradient (NNCG) method is presented. The NNCG method is comparable in terms of accuracy to the state-of-the-art method, projected Gauss...

Design considerations for incineration of transuranic-contaminated solid wastes

International Nuclear Information System (INIS)

Koenig, R.A.

1977-01-01

The Los Alamos Scientific Laboratory has established a development program to evaluate alternate production-level (100-200 lb/hr throughput) volume reduction processes for transuranic-contaminated solid waste. The first process selected for installation and study is based on controlled-air incineration. Design considerations leading to selection of feed preparation, incineration, residue removal, and off-gas cleanup components and their respective radioactive containment provisions will be presented

Environmental aspects of the transuranics. A selected, annotated bibliography. Volume 9

International Nuclear Information System (INIS)

Ensminger, J.T.; Fore, C.S.; Dailey, N.S.

1978-09-01

This ninth published bibliography of 589 references is compiled from the Nevada Applied Ecology Information Center's Data Base on the Environmental Aspects of the Transuranics. The data base was built to provide information support to the Nevada Applied Ecology Group (NAEG) of DOE's Nevada Operations Office. The general scope covers environmental aspects of uranium and the transuranic elements, with emphasis on plutonium. This annotated bibliography highlights literature on plutonium 238 and 239 and americium 241 in the critical organs of man and animals. Studies on the migration of plutonium and the transplutonics through the environment are also emphasized. Supporting information on ecology of the Nevada Test Site and reviews and summarizing literature on other radionuclides have been included at the request of the NAEG. The references are arranged by subject category with leading authors appearing alphabetically within each category. Indexes are provided for author(s), geographic location, keywords, taxonomic name, title, and publication description

Safety analysis report for the TRUPACT-II shipping package (condensed version). Volume 1, Rev. 14

International Nuclear Information System (INIS)

1994-10-01

The condensed version of the TRUPACT-II Contact Handled Transuranic Waste Safety Analysis Report for Packaging (SARP) contains essential material required by TRUPACT-II users, plus additional contents (payload) information previously submitted to the U.S. Nuclear Regulatory Commission. All or part of the following sections, which are not required by users of the TRUPACT-II, are deleted from the condensed version: (i) structural analysis, (ii) thermal analysis, (iii) containment analysis, (iv) criticality analysis, (v) shielding analysis, and (vi) hypothetical accident test results

Safety analysis report for the TRUPACT-II shipping package (condensed version). Volume 1, Rev. 14

Energy Technology Data Exchange (ETDEWEB)

NONE

1994-10-01

The condensed version of the TRUPACT-II Contact Handled Transuranic Waste Safety Analysis Report for Packaging (SARP) contains essential material required by TRUPACT-II users, plus additional contents (payload) information previously submitted to the U.S. Nuclear Regulatory Commission. All or part of the following sections, which are not required by users of the TRUPACT-II, are deleted from the condensed version: (i) structural analysis, (ii) thermal analysis, (iii) containment analysis, (iv) criticality analysis, (v) shielding analysis, and (vi) hypothetical accident test results.

Evaluation of diminished microbial contamination in handling of a novel daily disposable flat pack contact lens.

Science.gov (United States)

Nomachi, Miya; Sakanishi, Kotaro; Ichijima, Hideji; Cavanagh, H Dwight

2013-05-01

To evaluate the efficacy of a novel daily disposable (DD) flat package in regard to microbial contamination on the anterior and posterior surfaces of a contact lens (CL) during handling of the lens for insertion. Four kinds of commercially available general blister-packed daily disposable contact lenses (DD CLs) as controls and a novel Magic 1-day Menicon Flat Pack as a test lens were used for this in vitro study. Lenses were removed from their packages using fingers coated with fluorescein 3 to 5 μm beads or an approximately 7×10(2) to 2×10(3) colony-forming unit (CFU)/mL Staphylococcus aureus suspension. The transfer of fluorescein beads to the surface of the lenses was then observed by fluorescence microscopy. Microbial contamination on the lenses was observed by light microscopy after a 2-day incubation period; and, the number of colonies isolated from the contaminated lenses was determined after 4 days of incubation. The number of fluorescein beads on the Magic lens was significantly less (p<0.05) than that of the general blister-packed control lenses. Adherence of microbial colonies was observed on both inner and outer surfaces of general blister-packed lenses, whereas no colony formation was found on the inner surface of the Magic lens, and the lowest bacterial adherence was observed for the Magic lens. The data demonstrated that placement of the Magic DD lens onto the eye is accompanied by diminished microbial contamination compared with general blister-packed DD CLs. Eye care professionals; however, should instruct patients to comply with intended use of DD CLs to prevent CL-associated microbial keratitis. In all cases, hand washing is mandated prelens insertion.

Holding a handle for balance during continuous postural perturbations – immediate and transitionary effects on whole body posture

Directory of Open Access Journals (Sweden)

Jernej Camernik

2016-09-01

Full Text Available When balance is exposed to perturbations, hand contacts are often used to assist postural control. We investigated the immediate and the transitionary effects of supportive hand contacts during continuous anteroposterior perturbations of stance by automated waist-pulls. Ten young adults were perturbed for five minutes and required to maintain balance by holding to a stationary, shoulder-high handle and following its removal. Centre of pressure (COP displacement, hip, knee, and ankle angles, leg and trunk muscle activity and handle contact forces were acquired. The analysis of results show that COP excursions are significantly smaller when the subjects utilize supportive hand contact and that the displacement of COP is strongly correlated to the perturbation force and significantly larger in the anterior than posterior direction. Regression analysis of hand forces revealed that subjects utilized the hand support significantly more during the posterior than anterior perturbations. Moreover, kinematical analysis showed that utilization of supportive hand contacts alters posture of the whole body and that postural readjustments after the release of the handle occur at different time scales in the hip, knee, and ankle joints. Overall, our findings show that supportive hand contacts are efficiently used for balance control during continuous postural perturbations and that utilization of a handle has significant immediate and transitionary effects on whole body posture.

Online high sensitivity measurement system for transuranic aerosols

International Nuclear Information System (INIS)

Kordas, J.F.; Phelps, P.L.

1976-01-01

A measurement system for transuranic aerosols has been designed that will be able to withstand the corrosive nature of stack effluents and yet have extremely high sensitivity. It will be capable of measuring 1 maximum permissible concentration (MPC) of plutonium or americium in 30 minutes with a fractional standard deviation of less than 0.33. Background resulting from 218 Po is eliminated by alpha energy discrimination and a decay scheme analysis. A microprocessor controls all data acquisition, data reduction, and instrument calibration

Dry separation technology of transuranic elements

International Nuclear Information System (INIS)

Inoue, Tadashi

1999-01-01

The separation principle of transuranic elements (TRU) by a dry method, the separation technique of TRU from a high level waste solution and a dry recycle technology of LWR and FBR fuel cycle are explained. The dry method used molten salt and liquid metal. TRU and the rare earth elements in the molten salt (LiCl-KCl, LiCl-KCl/Cd and LiCl-KCl/Bi system) were separated by two methods such as the electrolytic refining and the reduction-extraction method. The former method separated 98% U, Np and Pu, but low Am. The latter method was able to separate more than 99.9% Np and Pu and 99.7% Am. (S.Y.)

Recovery of transuranics from process residues

International Nuclear Information System (INIS)

Gray, J.H.; Gray, L.W.

1987-01-01

Process residues are generated at both the Rocky Flats Plant (RFP) and the Savannah River Plant (SRP) during aqueous chemical and pyrochemical operations. Frequently, process operations will result in either impure products or produce residues sufficiently contaminated with transuranics to be nondiscardable as waste. Purification and recovery flowsheets for process residues have been developed to generate solutions compatible with subsequent Purex operations and either solid or liquid waste suitable for disposal. The ''scrub alloy'' and the ''anode heel alloy'' are examples of materials generated at RFP which have been processed at SRP using the developed recovery flowsheets. Examples of process residues being generated at SRP for which flowsheets are under development include LECO crucibles and alpha-contaminated hydraulic oil

Incorporation of transuranics into vegetable and field crops grown at the Nevada Test Site

International Nuclear Information System (INIS)

Au, F.H.F.; Leavitt, V.D.; Beckert, W.F.; McFarlane, J.C.

1977-01-01

Radish, lettuce, barley, and alfalfa plants were grown from seeds in undisturbed soil in Area 13 of the Nevada Test Site to determine the uptake of transuranics under field conditions. The plants were grown in small greenhouses erected over the soil to preclude aerial deposition of resuspended transuranics on the growing plants. The crops were irrigated during the growing season with either distilled water, diethylenetriaminepentaacetic acid (DTPA) in distilled water, fertilizer in distilled water, or a combination of DTPA and fertilizer in distilled water. The plutonium and americium contents of the harvested plants showed differences which are mostly attributable to the effects of the treatments and the resulting changes in soil pH during the experiment

Distribution of transuranic elements in a freshwater pond ecosystem

International Nuclear Information System (INIS)

Emery, R.M.; Klopfer, D.C.

1975-05-01

Preliminary results are reported from a study initiated on the Hanford Reservation concerning the ecological behavior of 238 Pu, 239 Pu, 240 Pu, and 241 Am in a freshwater environment. This study involves a waste pond which has been receiving Pu processing wastes for about 30 years. The pond has a sufficiently established ecosystem to provide an excellent location for limnological characterization. In addition, the ecological distribution of Pu and Am was investigated. The pond is also highly enriched with nutrients, thus supporting a high level of algal and macrophyte production. Seston (30 percent diatoms) appears to be the principal concentrators of Pu transuranics in the pond system. The major sink for Pu and Am in this system is the sediments. Organic floc, overlaying the pond sediments, is also a major concentrator of transuranics in this system []Aside from the seston and floc, no other ecological components of the pond appear to have concentrations significantly greater than those of the sediment. Dragonfly, larvae, watercress, and snails show concentrations which approximate those of the sediments but nearly all other food web components have levels of Pu and Am which are lower than those of the sediments, thus, Pu and Am seem to be relatively immobile in the aquatic ecosystem. (CH)

Measurements of fission and activation products for Oak Ridge National Laboratory transuranic waste characterization

International Nuclear Information System (INIS)

Nguyen, L.K.; Miller, L.F.; Downing, D.J.

1997-06-01

It is beyond the current nondestructive analysis (NDA) state-of-the-art to accurately measure important alpha- and beta-emitting radionuclides in the presence of typically-occurring background levels of neutron and photon radiation associated with remote handled (RH) transuranic (TRU) waste; in addition, it is not economically feasible to perform destructive analyses (DA) that employ radiochemical techniques on representative random samples from each waste container designated for disposal. Techniques that utilize gamma spectroscopy cannot measure purely alpha-emitting radionuclides, and they are difficult for measurements of photon-emitting radionuclides in large containers with energies below about one hundred keV. The methodology presented in this report combines gamma spectroscopy measurements of waste canisters with radiochemical analyses of smear samples and with statistical analyses to obtain estimates of alpha-emitting radionuclides in waste containers. This approach, with some additional research, is expected to provide an effective and practical technique for characterization of TRU radioactive waste to meet the Waste Isolation Pilot Plant (WIPP) waste acceptance criteria (WAC) and for segregating waste at the Radiochemical Engineering Development Center (REDC). The objectives of this report are to determine if a waste container generated from ORNL/REDC can be classified as TRU and to provide an appropriate method of estimating the initial TRU concentration in this container

Safety analysis and inventory control of transuranic and low-level waste in common storage

International Nuclear Information System (INIS)

Porten, D.R.; Bonner, A.L.; Joyce, J.P.

1993-01-01

This paper describes a methodology developed For the inventory control of low-level waste (LLW) and transuranic (TRU) waste, when both are stored in the same location, and both contribute to an inventory constrained by safety considerations. Development of the method arose from the necessity to make safety analysis calculations for the addition of LLW, in quantities greater than existing inventory limits would allow when stored with TRU waste, in the Hanford Central Waste Complex (CWC)-Ensuring that the dose consequences of credible releases are maintained at low-hazard limits or less, was used to allow greater than Type A quantities of LLW into the CWC. Basically, what happens is the original limited amount of TRU allowed is reduced by some equivalent amount of LLW introduced. The total quantity of TRU, and LLW in excess of Type A quantities, must be administratively maintained via curie equivalency Factors to ensure operation as a low-hazard Facility. The ''equivalency'' between TRU and LLW proposed here is specific only to the CWC, but the methodology can be used for other specific applications, such as TRU and LLW storage or handling facilities where inventory limits must be enforced or where a simplified inventory system is required

Methods for removing transuranic elements from waste solutions

International Nuclear Information System (INIS)

Slater, S.A.; Chamberlain, D.B.; Connor, C.; Sedlet, J.; Srinivasan, B.; Vandegrift, G.F.

1994-11-01

This report outlines a treatment scheme for separating and concentrating the transuranic (TRU) elements present in aqueous waste solutions stored at Argonne National Laboratory (ANL). The treatment method selected is carrier precipitation. Potential carriers will be evaluated in future laboratory work, beginning with ferric hydroxide and magnetite. The process will result in a supernatant with alpha activity low enough that it can be treated in the existing evaporator/concentrator at ANL. The separated TRU waste will be packaged for shipment to the Waste Isolation Pilot Plant

Transuranic-waste program at EG and G Idaho, Inc. Annual technical report

International Nuclear Information System (INIS)

McKinley, K.B.

1982-11-01

This report summarizes the objectives and accomplishments of Transuranic (TRU) Waste Program conducted at EG and G Idaho, Inc., during FY 1982. The TRU Waste Program included: (1) Preparation of a revised draft of the Recommendation of a Long-Term Strategy (RLTS) document; (2) Preparation of environmental documentation, including a technical report, Environmental and Other Evaluations of Alternatives for Management of Defense Transuranic Waste at the Idaho National Engineering Laboratory, IDO-10103, as well as two environmental evaluations; (3) Preparation of a certification plan and procedures; (4) A nondestructive examination (NDE) project, which includes development of real-time radiography for waste certification, and container integrity equipment for waste container certification; (5) Development of an assay system; (6) Completion of a conceptual design for the Stored Waste Examination Pilot Plant (SWEPP) and SWEPP Support; and (7) Gas-generation analyses and tests. These TRU waste projects were funded at $1640K

Role of animal toxicity studies in the evaluation of human health risks from internally deposited transuranics

International Nuclear Information System (INIS)

Thompson, R.C.

1977-02-01

The extrapolation of animal data to man has always been a problem for those concerned with human biology. Especially if one is interested in the effects of toxicants, opportunities for direct observation in man are usually limited, and approval of planned experiments employing human subjects is difficult to obtain. In no case are these limitations more restrictive than for transuranic elements, for which no life-threatening effects have yet been demonstrated in man. This lack of human experience is coupled with a massive public concern over possible future effects of transuranics, which contrasts sharply with the general public apathy toward a multitude of present environmental pollutants of clearly established toxicity. This concern for the transuranics, especially 239 Pu, and for other radionuclides has prompted the expenditure of many millions of dollars (and francs and marks and pounds and roubles) on studies to investigate their toxicity in animals. Results of these studies are extensive, and still accumulating, but in many quarters there is now a reluctance to accept these results as relevant to the prediction of human effects

Waste Isolation Pilot Plant Transuranic Waste Baseline inventory report. Volume 1. Revision 1

International Nuclear Information System (INIS)

1995-02-01

This document provides baseline inventories of transuranic wastes for the WIPP facility. Information on waste forms, forecasting of future inventories, and waste stream originators is also provided. A diskette is provided which contains the inventory database

Waste Isolation Pilot Plant Transuranic Waste Baseline inventory report. Volume 1. Revision 1

Energy Technology Data Exchange (ETDEWEB)

NONE

1995-02-01

This document provides baseline inventories of transuranic wastes for the WIPP facility. Information on waste forms, forecasting of future inventories, and waste stream originators is also provided. A diskette is provided which contains the inventory database.

Physical Properties of Hanford Transuranic Waste

Energy Technology Data Exchange (ETDEWEB)

Berg, John C.

2010-03-25

The research described herein was undertaken to provide needed physical property descriptions of the Hanford transuranic tank sludges under conditions that might exist during retrieval, treatment, packaging and transportation for disposal. The work addressed the development of a fundamental understanding of the types of systems represented by these sludge suspensions through correlation of the macroscopic rheological properties with particle interactions occurring at the colloidal scale in the various liquid media. The results of the work have advanced existing understanding of the sedimentation and aggregation properties of complex colloidal suspensions. Bench scale models were investigated with respect to their structural, colloidal and rheological properties that should be useful for the development and optimization of techniques to process the wastes at various DOE sites.

Strategic management of health risks posed by buried transuranic wastes

International Nuclear Information System (INIS)

Jump, R.A.

1994-01-01

A strategy is presented for reducing health risks at sites contaminated with buried transuranic (TRU) wastes by first taking measures to immobilize the contaminants until the second step, final action, becomes cost-effective and poses less risk to the remediation workers. The first step of this strategy does not preclude further action if it is warranted and is in harmony with environmental laws and regulations

Transuranic radionuclides in the Columbia River: sources, inventories, and geochemical behavior

International Nuclear Information System (INIS)

Beasley, T.M.

1987-01-01

The sources, inventories, and geochemical behavior of transuranic and other long-lived radionuclides in the lower Columbia River are summarized. Inventories have been estimated from the measured activities of the different radionuclides in 50 cores raised in 1977 and 1978, while annual export of transuranic radionuclides was determined from monthly water collections in the estuary. Continental shelf inventories of Pu and Am isotopes have been estimated using excess 210 Pb inventories and the mean 210 Pb//sup 239,240/Pu inventory ratio of 100 +/- 19 observed in representative cores raised from the shelf. Despite the substantial past addition of radioactivity to the river from operation of the plutonium production reactors at Hanford, the amounts of reactor-derived radionuclides in river sediments are small relative to fallout-derived nuclides. Erosional processes have mobilized both fallout-derived /sup 239,240/Pu and 137 Cs from the landscape to the river, but the quantities involved represent <1% of their fallout inventories within the river's drainage basin. 36 references, 6 figures, 2 tables

Shredder and incinerator technology for volume reduction of commercial transuranic wastes

International Nuclear Information System (INIS)

Oma, K.H.

1986-06-01

Pacific Northwest Laboratory (PNL) is evaluating alternatives and developing technology for treatment of radioactive wastes generated during commercial nuclear activities. Transuranic wastes that require volume reduction include spent HEPA filters, sample and analytical cell waste, and general process trash. A review of current technologies for volume reduction of these wastes led to the selection and testing of several low-speed shredder systems and three candidate incineration processes. The incinerators tested were the electrically heated control-led-air, gas-heated controlled-air, and rotary kiln. Equipment tests were conducted using simulated commercial transuranic wastes to provide a data base for the comparison of the various technologies. The electrically driven, low-speed shredder process was selected as the preferred method for size reduction of the wastes prior to incineration. All three incinerators effectively reduced the waste volume. Based on a technical and economic evaluation on the incineration processes, the recommended system for the commercial waste application is the gas-heated controlled-air incinerator with a single stage of shredding for feed pretreatment

US experience with acid digestion of combustible transuranic wastes

International Nuclear Information System (INIS)

Allen, C.R.; Lerch, R.E.

1982-09-01

Contaminated transuranic waste from a plutonium finishing plant has been processed in a waste treatment demonstration plant, the Radioactive Acid Digestion Test Unit (RADTU) located at Hanford, Washington, USA. Waste treatment experience, including process and equipment performance, the behavior of plutonium in the system, and chemical and nuclear safety are all discussed. The complementary relationship of this research and development to that at the ALONA pilot plant in Mol, Belgium is noted. 7 figures, 4 tables

Search for far transuranic elements in galactic comic rays

International Nuclear Information System (INIS)

Perelygin, V.P.; Lkhagvasuren, D.; Otgonsuren, O.; Stetsenko, S.G.; Yakupi, B.

1976-01-01

Experimental results on the search for the tracks of far transuranic elements of the galactic origin in olivine crystals from Marjalahti meteorite are presented. A total af 174 mm 3 of olivines taken from the surface layers of the meteorite and 60 mm 3 taken from its inner parts have been examined. The upper limit of the abundance of the Z >= 110 nuclei has been established to be -9 of the abundance of the Fe group nuclei. (orig.) [de

Environmental aspects of the transuranics: a selected, annotated bibliography. [Pu-238, Pu-239

Energy Technology Data Exchange (ETDEWEB)

Ensminger, J.T.; Martin, F.M.; Fore, C.S. (comps.)

1977-03-01

This eighth published bibliography of 427 references is compiled from the Nevada Applied Ecology Information Center's Data Base on the Environmental Aspects of the Transuranics. The data base was built to provide information support to the Nevada Applied Ecology Group (NAEG) of ERDA's Nevada Operations Office. The general scope covers environmental aspects of uranium and the transuranic elements, with emphasis on plutonium. This bibliography highlights literature on plutonium 238 and 239 and americium in the critical organs of man and animals. Supporting information on ecology of the Nevada Test Site and reviews and summarizing literature on other radionuclides have been included at the request of the NAEG. The references are arranged by subject category with leading authors appearing alphabetically in each category. Indexes are provided for author(s), geographic location, keyword(s), taxon, title, and publication description.

High Efficiency Particulate Air (HEPA) Filter Generation, Characterization, and Disposal Experiences at the Oak Ridge National Laboratory

International Nuclear Information System (INIS)

Coffey, D. E.

2002-01-01

High Efficiency Particulate Air filtration is an essential component of the containment and ventilation systems supporting the research and development activities at the Oak Ridge National Laboratory. High Efficiency Particulate Air filters range in size from 7.6cm (3 inch) by 10.2 cm (4 inch) cylindrical shape filters to filter array assemblies up to 2.1 m (7 feet) high by 1.5 m (5 feet) wide. Spent filters are grouped by contaminates trapped in the filter media and become one of the components in the respective waste stream. Waste minimization and pollution prevention efforts are applied for both radiological and non-radiological applications. Radiological applications include laboratory hoods, glove boxes, and hot cells. High Efficiency Particulate Air filters also are generated from intake or pre-filtering applications, decontamination activities, and asbestos abatement applications. The disposal avenues include sanitary/industrial waste, Resource Conservation and Recovery Act and Toxic Substance Control Act, regulated waste, solid low-level waste, contact handled transuranic, and remote handled transuranic waste. This paper discusses characterization and operational experiences associated with the disposal of the spent filters across multiple applications

Original Article Effect of Soft Contact Lens Materials on Tear Film ...

African Journals Online (AJOL)

problems, results in intolerance of contact lens wear and damage (Foulks, ... reported that contact lens-related dry eye may be ... eliminating or modifying the refractive error ..... risk of eye infection, easier handling due to ... Adv Exp Med Biol.

Combustion and fuel loading characteristics of Hanford Site transuranic solid waste

International Nuclear Information System (INIS)

Greenhalgh, W.O.

1994-01-01

The Waste Receiving and Processing (WRAP) Facility is being designed for construction in the north end of the Central Waste Complex. The WRAP Facility will receive, store, and process radioactive solid waste of both transuranic (TRU) and mixed waste (mixed radioactive-chemical waste) categories. Most of the waste is in 208-L (55-gal) steel drums. Other containers such as wood and steel boxes, and various sized drums will also be processed in the facility. The largest volume of waste and the type addressed in this report is TRU in 208-L (55-gal) drums that is scheduled to be processed in the Waste Receiving and Processing Facility Module 1 (WRAP 1). Half of the TRU waste processed by WRAP 1 is expected to be retrieved stored waste and the other half newly generated waste. Both the stored and new waste will be processed to certify it for permanent storage in the Waste Isolation Pilot Plant (WIPP) or disposal. The stored waste will go through a process of retrieval, examination, analysis, segregation, repackaging, relabeling, and documentation before certification and WIPP shipment. Newly generated waste should be much easier to process and certify. However, a substantial number of drums of both retrievable and newly generated waste will require temporary storage and handling in WRAP. Most of the TRU waste is combustible or has combustible components. Therefore, the presence of a substantial volume of drummed combustible waste raises concern about fire safety in WRAP and similar waste drum storage facilities. This report analyzes the fire related characteristics of the expected WRAP TRU waste stream

Medical Effects of a Transuranic "Dirty Bomb".

Science.gov (United States)

Durakovic, Asaf

2017-03-01

The modern military battlefields are characterized by the use of nonconventional weapons such as encountered in the conflicts of the Gulf War I and Gulf War II. Recent warfare in Iraq, Afghanistan, and the Balkans has introduced radioactive weapons to the modern war zone scenarios. This presents the military medicine with a new area of radioactive warfare with the potential large scale contamination of military and civilian targets with the variety of radioactive isotopes further enhanced by the clandestine use of radioactive materials in the terrorist radioactive warfare. Radioactive dispersal devices (RDDs), including the "dirty bomb," involve the use of organotropic radioisotopes such as iodine 131, cesium 137, strontium 90, and transuranic elements. Some of the current studies of RDDs involve large-scale medical effects, social and economic disruption of the society, logistics of casualty management, cleanup, and transportation preparedness, still insufficiently addressed by the environmental and mass casualty medicine. The consequences of a dirty bomb, particularly in the terrorist use in urban areas, are a subject of international studies of multiple agencies involved in the management of disaster medicine. The long-term somatic and genetic impact of some from among over 400 radioisotopes released in the nuclear fission include somatic and transgenerational genetic effects with the potential challenges of the genomic stability of the biosphere. The global contamination is additionally heightened by the presence of transuranic elements in the modern warzone, including depleted uranium recently found to contain plutonium 239, possibly the most dangerous substance known to man with one pound of plutonium capable of causing 8 billion cancers. The planning for the consequences of radioactive dirty bomb are being currently studied in reference to the alkaline earths, osteotropic, and stem cell hazards of internally deposited radioactive isotopes, in particular

Integrative study of the behavior of transuranic elements in the marine environment. Progress report, June 1, 1981-May 31, 1982

International Nuclear Information System (INIS)

Choppin, G.R.; Morse, J.W.

1981-12-01

The laboratory at Florida State University is conducting fundamental research under marine conditions of the speciation of actinide elements in sea water. At the Texas A and M University, the adsorption of actinides from such solutions upon various components of sediments is being studied. This approach should yield radiochemical data directly applicable to the understanding of the distribution and speciation of transuranic elements in the marine environment. A limited number of common sediment components are being studied to determine which factors determine the partitioning of transuranic elements among these components. The individual components then will be combined in synthetic sediments of increasing complexity and the distributions studied between these sediments and solutions. Hopefully, this will lead to studies agreeing with model predictions for the adsorption of transuranic elements in marine sediments

Development of a telerobotic system for handling contaminated process equipment

International Nuclear Information System (INIS)

Fisher, J.J.; Ward, C.R.; Schuler, T.F.

1987-01-01

E. I. du Pont de Nemours and Company is evaluating a unique eight-degree-of-freedom Telerobot manipulator to perform size-reduction and material handling operations on contaminated process equipment at the Savannah River Plant (SRP). The Telerobot will be installed in the proposed Transuranic (TRU) Waste Processing Facility, which is scheduled to be operational by 1990. A full-scale prototype Telerobot, manufactured by GCA Corporation, St. Paul, MN is being tested with other process equipment in the Components Test Facility at the Savannah River Laboratory (SRL). All telerobotic operations required in the TRU Waste Facility such as crate unpacking, equipment dismantling, material size-reduction, and selected maintenance operations are being tested. This paper discusses the major mechanical and control features of the Telerobot system. Several system enhancements were added by SRL, including a new quick-hand-change coupling and expanded software control functions. The new software enables a system operator to perform both teleoperated and automatic tasks through several operating modes. These enhancements, as well as future mechanical, control system, and software features, are reviewed

Transuranic waste characterization sampling and analysis methods manual. Revision 1

International Nuclear Information System (INIS)

Suermann, J.F.

1996-04-01

This Methods Manual provides a unified source of information on the sampling and analytical techniques that enable Department of Energy (DOE) facilities to comply with the requirements established in the current revision of the Transuranic Waste Characterization Quality Assurance Program Plan (QAPP) for the Waste Isolation Pilot Plant (WIPP) Transuranic (TRU) Waste Characterization Program (the Program) and the WIPP Waste Analysis Plan. This Methods Manual includes all of the testing, sampling, and analytical methodologies accepted by DOE for use in implementing the Program requirements specified in the QAPP and the WIPP Waste Analysis Plan. The procedures in this Methods Manual are comprehensive and detailed and are designed to provide the necessary guidance for the preparation of site-specific procedures. With some analytical methods, such as Gas Chromatography/Mass Spectrometry, the Methods Manual procedures may be used directly. With other methods, such as nondestructive characterization, the Methods Manual provides guidance rather than a step-by-step procedure. Sites must meet all of the specified quality control requirements of the applicable procedure. Each DOE site must document the details of the procedures it will use and demonstrate the efficacy of such procedures to the Manager, National TRU Program Waste Characterization, during Waste Characterization and Certification audits

Adaptive contact elements for three-dimensional fluid-structure interfaces

International Nuclear Information System (INIS)

Kulak, R.F.

1985-01-01

A finite element method is developed for treating the mechanics of contact between two deformable bodies which occurs, for example, at fluid-structure interfaces. The method uses a family of adaptive contact elements, which are based upon the penalty method, to handle all of the possible contact configurations that can occur between the discretized contacting bodies. The contact element's nodal connectivity is allowed to change during the computations in order to accommodate finite sliding. The infusion of these elements in the interface results in satisfying the force equilibrium condition during contact. The methodology has been implemented into the NEPTUNE code. Results are presented for an illustrative problem

Adaptive contact elements for three-dimensional fluid-structure interfaces

Energy Technology Data Exchange (ETDEWEB)

Kulak, R.F.

1985-01-01

A finite element method is developed for treating the mechanics of contact between two deformable bodies which occurs, for example, at fluid-structure interfaces. The method uses a family of adaptive contact elements, which are based upon the penalty method, to handle all of the possible contact configurations that can occur between the discretized contacting bodies. The contact element's nodal connectivity is allowed to change during the computations in order to accommodate finite sliding. The infusion of these elements in the interface results in satisfying the force equilibrium condition during contact. The methodology has been implemented into the NEPTUNE code. Results are presented for an illustrative problem.

Hanford transuranic storage corrosion review

International Nuclear Information System (INIS)

Nelson, J.L.; Divine, J.R.

1980-12-01

The rate of atmospheric corrosion of the transuranic (TRU) waste drums at the US Department of Energy's Hanford Project, near Richland, Washington, was evaluated by Pacific Northwest Laboratory (PNL). The rate of corrosion is principally contingent upon the effects of humidity, airborne pollutants, and temperature. Results of the study indicate that actual penetration of barrels due to atmospheric corrosion will probably not occur within the 20-year specified recovery period. Several other US burial sites were surveyed, and it appears that there is sufficient uncertainty in the available data to prevent a clearcut statement of the corrosion rate at a specific site. Laboratory and site tests are recommended before any definite conclusions can be made. The corrosion potential at the Hanford TRU waste site could be reduced by a combination of changes in drum materials (for example, using galvanized barrels instead of the currently used mild steel barrels), environmental exposure conditions (for example, covering the barrels in one of numerous possible ways), and storage conditions

Transuranics Laboratory, achievements and performance

International Nuclear Information System (INIS)

Gasco, C.; Anton, M. P.

2004-01-01

The Marine and Aquatic Radioecology Group (MARG) was established in 1985 with the main scope of analysing the consequences of the Palomares accident in the adjacent Mediterranean ecosystem. From then on and up to now , this Group has extended its investigations to other European marine environments, such as the Spanish Mediterranean margin, the Artic and the Atlantic. The main research of long-lived radionuclides (plutonium, americium and Cs-137) determining the orography influence, riverine inputs and their geo-chemical associations. This group is currently accomplishing new challenges on the radioecology field such as the development of techniques for transuranics speciation to determine their geo-chemical association to the main sediment compounds. Natural and anthropogenic radionuclides distribution on salt-marsh areas affected by dry-wet periods is being studied as well as the possibilities of fusing crossed techniques for dating recent sediments (pollen, anthropogenic, ''210 Pb, etc). The Laboratory performance description, the procedures used, calculations, challenges and gaps are described in this report. (Author) 22 refs

Determination of the distribution of uranium and the transuranic elements in the environment by thermal ionization mass spectrometry

International Nuclear Information System (INIS)

Chastagner, P.

1987-01-01

Protection of the world population from releases of uranium, plutonium, and other transuranic materials requires, among other things, a knowledge of the sources, transport, and distribution of these elements in the environment. Both isotopic and quantitative analytical data are required in the determination of these factors. Also, the analyses must be precise and accurate enough to distinguish newly released material from older material such as the worldwide deposits from atmospheric weapons testing. For this reason, uranium, neptunium, and plutonium and other transuranic elements in the environment are routinely determined by high-sensitivity thermal ionization mass spectrometric techniques. With current instrumentation and techniques, routine isotope dilution and isotopic analyses are made with purified elemental samples as small as 2 x 10 -14 g. The detection limit for uranium and most of the transuranic isotopes is ∼ 5 x 10 18 g (∼ 13,000 atoms), which is at least an order of magnitude better than the detection limits of the radiometric counting techniques normally employed. The mass spectral sensitivities are equal for all of the isotopes of a given element but vary from element to element. Thus, each elemental sample must be highly purified. Separation techniques recover ∼ 80% of the uranium and the transuranic material from soils and other materials. Interelement separation factors > 10 5 are achieved with advanced ion exchange methods. Results of recent application of these techniques at the Savannah River Lab. and other laboratories are include

Transuranic elements in nature - plutonium all around us

International Nuclear Information System (INIS)

Keller, C.; Baptista de Alleluia, I.

1979-01-01

At first the transuranic element plutonium was thought to be an artificial element which was formed during nuclear reactions. However, in the earth's crust traces of plutonium have also been found which has constantly been renewing itself ever since the birth of our solar system. But it is the quantities of artificially produced plutonium which make up the bulk of this element on our planet. Part of it has spread fairly equally over the whole of the earth. Plutonium can be proved to exist on every field an in every sample of air today. (orig.) [de

Transuranic depositional history in South Greenland firn layers

International Nuclear Information System (INIS)

Koide, M.; Goldberg, E.D.; Herron, M.M.; Langway, C.C. Jr.

1977-01-01

It is stated that the surface layers of the Greenland ice sheet have preserved a continuous and detailed record of atmospheric fallout of transuranic nuclides from weapons tests over the past 30 yr. It was found that fallout maxima occurred in the 1950s and 1960s for sup(239+240)Pu and in 1965-66 for 238 Pu. This work may be extended by using alpine glaciers in mid-latitudes for a reconstruction of fallout patterns over the past three decades for an evaluation of present day dispersions of these nuclides as a consequence of atmospheric fallout and other possible entries. (author)

Synthesis of neutron-rich transuranic nuclei in fissile spallation targets

OpenAIRE

Mishustin, Igor; Malyshkin, Yury; Pshenichnov, Igor; Greiner, Walter

2014-01-01

A possibility of synthesizing neutron-reach super-heavy elements in spallation targets of Accelerator Driven Systems (ADS) is considered. A dedicated software called Nuclide Composition Dynamics (NuCoD) was developed to model the evolution of isotope composition in the targets during a long-time irradiation by intense proton and deuteron beams. Simulation results show that transuranic elements up to Bk-249 can be produced in multiple neutron capture reactions in macroscopic quantities. Howeve...

Research and development plans for disposal of high-level and transuranic wastes

International Nuclear Information System (INIS)

Bartlett, J.W.; Platt, A.M.

1978-09-01

This plan recommends a 20-year, 206 million (1975 $'s) R and D program on geologic structures in the contiguous U.S. and on the midplate Pacific seabed with the objective of developing an acceptable method for disposal of commercial high-level and transuranic wastes by 1997. No differentiation between high-level and transuranic waste disposal is made in the first 5 years of the program. A unique application of probability theory to R and D planning establishes, at a 95% confidence level, that the program objective will be met if at least fifteen generic options and five specific disposal sites are explored in detail and at least two pilot plants are constructed and operated. A parallel effort on analysis and evaluation maximizes information available for decisions on the acceptability of the disposal techniques. Based on considerations of technical feasibility, timing and technical risk, the other disposal concepts, e.g., ice sheets, partitioning, transmutation and space disposal cited in BNWL-1900 are not recommended for near future R and D

Application to ship nonmixed transuranic waste to the Nevada Test Site for interim storage

International Nuclear Information System (INIS)

1993-12-01

This report documents various regulations on radioactive waste processing and discusses how the Waste Isolation Pilot Plant will comply with and meet these requirements. Specific procedures are discussed concerning transuranic, metal scrap, salt block, solid, and glove box wastes

Chemical speciation and bioavailability of transuranics for a freshwater snail (Lymnaea stagnalis L.)

International Nuclear Information System (INIS)

Thiels, G.M.; Murray, C.N.; Rade, J.

1981-01-01

It is now becoming clear that the determination of the physico-chemical forms of transuranic elements is an important step in assessing their behaviour at very low environmental levels. Data from both simulated environmental systems as well as in-situ investigations have shown the necessity of understanding the source term of contamination, which probably plays a major role in the long-term distribution of these elements. In the present paper an experimental procedure is outlined, which allows a more extensive investigation into some aspects of the biogeochemical behaviour of two transuranics: 237 Pu and 241 Am. Two chemical methods were applied to a study of the freshwater snail Lymnaea stagnalis L.. Data were obtained on the uptake and retention patterns of different oxidation states of 237 Pu and 241 Am at the organ and cellular levels of the pond snail. An attempt was made to relate the environmental chemistry of both radionuclides to the fixation in L. stagnalis. (author)

In situ vitrification of transuranic wastes: An updated systems evaluation and applications assessment

Energy Technology Data Exchange (ETDEWEB)

Buelt, J.L.; Timmerman, C.L.; Oma, K.H.; FitzPatrick, V.F.; Carter, J.G.

1987-03-01

In situ vitrification (ISV) is a process whereby joule heating immobilizes contaminated soil in place into a durable glass and crystalline waste form. Numerous technological advances made during the past three years in the design, fabrication, and testing of the ISV process are discussed. Performance analysis of ISV focuses on process equipment, element retention (in the vitrified soil during processing), melt geometry, depth monitors, and electrodes. The types of soil and waste processed by ISV are evaluated as process parameters. Economic data provide the production costs of the large-scale unit for radioactive and hazardous chemical wastes (wet and dry). The processing of transuranic-contaminated soils are discussed with respect to occupational and public safety. Alternative applications and operating sequences for various waste sites are identified. The technological data base warrants conducting a large-scale radioactive test at a contaminated soil site at Hanford to provide a representative waste form that can be evaluated to determine its suitability for in-place stabilization of transuranic-contaminated soils.

Data base of the environmental aspects of the transuranics

International Nuclear Information System (INIS)

Pfuderer, H.

1975-01-01

Indexed and abstracted references to the environmental aspects of the transuranium elements are entered into and are retrievable from a dynamic, computerized information file (or data base) that is easily modified to reflect changing research needs. The information is distilled from the documents with the specific needs of the researcher in mind, such as numeric results, new methods, or instrumentation. The major areas of evaluation are: biological and medical studies on the effects of the transuranics, particularly as these elements relate to health considerations in man; biological and ecological availability, turnover, and food chain dynamics; analysis of environmental materials; environmental transport mechanisms, including resuspension; waste disposal as related to environmental concerns; monitoring; and regulations and standards for environmental levels. Annotated references are indexed to allow easy access for retrieving references to documents of interest to the user. The goal is to furnish the users all the references related to their specific query and few that are unrelated. This is done by liberal use of subject categories and keyterms. The studies on man and animals are divided into the subject categories of medical and biological aspects. Those aspects that are considered important when the document is analyzed are tabulated. These data are sought for in the article, included in the abstracts, and indexed with keyterms. This checklist is one of the ways the Data Base on the Environmental Aspects of the Transuranics strives to give users a reference to every paper in their subject area

Multielement analysis of reagents used in chemical identification of transuranic elements

International Nuclear Information System (INIS)

Montalvan Estrada, A.; Brigido Flores, O.; Maslov, O.D.; Dmitriev, S.N.

2006-01-01

For more than 40 years, chemical identification of transuranic elements has been used at the Laboratory of Nuclear Reactions of the Join Institute for Nuclear Research, Dubna, Russia, as a secondary method of identification. Chlorination of transuranic elements obtained by nuclear reactions is an important step of the procedure in order to obtain volatile compounds able to pass through a thermo chromatographic process. To access the quality of the reagents TiCl 4 and SOCl 2 multielement analysis was carried out using both X-rays fluorescence and gamma activation. It was followed the simplest procedure for reagents samples pretreatment, so further interferences from other chemical products were avoided. X-rays fluorescence analysis was performed in a spectrometer with Si(Li) detector with a resolution for Fe (K?) of 190 eV. Both Cd-109 and Am-241 were used as isotopic sources of excitation. Gamma activation analysis was carried out using the compact electron accelerator MT-25, where gamma rays are produced in a stopping target. Among the parameters of the MT-25 are the following: energy range-10-25 MeV, gamma-ray flux-10 14 photon/s, power consumption-20 kw. Measurements of the induced activity were performed with the help of a HPGe detector, thin and coaxial Ge(Li) detectors. There were identified two elements in SOCl 2 -Nickel (3*10 -6 g/g) and Antimony (2*10 -7 g/g), while there were identified three elements in TiCl 4 - Zirconium (8*10 -7 g/g), Arsenic (9*10 -7 g/g) and Antimony (5*10 -7 g/g). Only five elements were detected in trace concentrations in the two analyzed reagents, that is for more than 57 elements capable of being detected using gamma activation analysis with the MT-25 only 5 had concentrations above the detection limits of the method. Not being chemical analogs of the synthesized transuranic elements (Z-104 and 106) and not being able to alpha or fission disintegrations there is not expected any interference from them in the chemical

Molten salt/metal extractions for recovery of transuranic elements

International Nuclear Information System (INIS)

Chow, L.S.; Basco, J.K.; Ackerman, J.P.; Johnson, T.R.

1992-01-01

The integral fast reactor (EFR) is an advanced reactor concept that incorporates metallic driver and blanket fuels, an inherently safe, liquid-sodium-cooled, pool-type, reactor design, and on-site pyrochemical reprocessing (including electrorefining) of spent fuels and wastes. This paper describes a pyrochemical method that is being developed at Argonne National Laboratory to recover transuranic elements from the EFR electrorefiner process salt. The method uses multistage extractions between molten chloride salts and cadmium metal at high temperatures. The chemical basis of the salt extraction method, the test equipment, and a test plan are discussed

Study of the land to sea transport of transuranic elements. Application to the Palomares Accident (Almeria 1966)

International Nuclear Information System (INIS)

Romero Gonzalez, L.

1991-01-01

The work presents a study on the land to sea transport of transuranic elements applied to a precise scenery at southern coast of Spain: the Palomares ecosystem, where in 1966 an accidental release of transuranics occurred (an USAF b-52 carrying four thermonuclear bombs). The study has been focused on the depositional history recorded in sediments from different sea depths. The experimental basis has been the measurement of Pu, Am, radiocaesium, and natural radionuclides in marine sediments from the referred zone, that involved the setting up of high sensitivity alpha and gamma spectrometry systems; the chronology of sediment was established by applying the CRS model to unsupported Pb-210 profiles. (author)

Neonates do not need to be handled for radiographs

International Nuclear Information System (INIS)

Slade, Dawn; Alfaham, Mazin; Davis, Peter; Tuthill, David; Harrison, Sara; Morris, Susan; Guildea, Zoe

2005-01-01

The handling of sick neonates may have detrimental effects such as hypoxia or bradycardia. Such handling is inevitable due to the frequent need for practical procedures; however, minimising handling reduces these adverse events and may improve outcome. Radiography is one of the commonest procedures performed on neonates. Usually the infant is lifted and placed onto the radiographic cassette; however, modern incubators often incorporate a tray beneath the mattress in which the radiographic cassette can be placed without the need to disturb the infant. To compare the quality of chest radiographs taken using the standard direct contact method, with those taken using the under-tray technique. A series of chest radiographs taken over a 21-month period were analysed independently by two consultant paediatric radiologists unaware of the radiographic details. The position of the radiograph, i.e. direct contact or under-tray, was determined by the radiographer. Radiographic quality was scored on the following features: exposure, blurring, rotation, cut-off or coning, and side markers. A subjective score was also included. The results from each radiologist were analysed separately. Seventy chest radiographs were analysed - 25 standard method, 45 under-tray. A statistically significant advantage for the under-tray method was seen on two analyses - radiologist 1 for exposure, and radiologist 2 for cut-off. No other significant differences were noted. There were no differences in the infants' weights or radiation exposure. The under-tray method for taking radiographs may produce films of at least equivalent quality to the standard method. Since the standard method involves handling with potential desaturation and bradycardia, this technique should cease. (orig.)

Concentrations of transuranic elements in critical organs and tissues of goats (CAPRA HIRCUS)

International Nuclear Information System (INIS)

Averin, V.S.; Vaskovtsova, V.A.; Kuhtsevich, A.B.; Tagai, S.A.; Tsarenok, A.A.; Buzdalkin, K.N.; Gvozdik, A.F.; Makarovets, I.V.; Nilova, E.K.

2012-01-01

Parameters of Am 241 and Pu 238, 239+240 transfer from the dietary soil-based component (mineral soil) to organs and tissues of goats during a grazing period of 80 and 160 days have been determined. The maximum specific activities of transuranic elements have been found in liver of goats. (authors)

Waste retrieval plan for the Waste Isolation Pilot Plant

International Nuclear Information System (INIS)

1993-03-01

The US DOE has prepared this plan to meet the requirements of Public Law 102579, the Waste Isolation Pilot Plant (WIPP) LWA, The purpose. is to demonstrate readiness to retrieve from the WIPP underground transuranic radioactive waste that will be used for testing should retrieval be needed. The WIPP, a potential geologic repository for transuranic wastes generated in national-defense activities, has been constructed in southeastern New Mexico. Because the transuranic wastes will remain radioactive for a very long time, the WIPP must reasonably ensure safe performance over thousands of years. The DOE therefore decided to develop the facility in phases, to preclude premature decisions and to conduct the performance assessments needed to demonstrate long-term safety. Surface facilities for receiving waste have been built, and considerable underground excavation, 2150 feet below the surface, has been completed. The next step is a test phase, including underground experiments called ''bin tests'' and ''alcove test(s)'' with contact-handled transuranic waste. The objective of these waste tests is to collect relevant data about the gas-generation potential and volatile organic compound (VOC) source term of the waste for developing a basis for demonstrating long term safety by compliance with the applicable disposal regulations (40 CFR 191, 264 and 268). The test phase will end when a decision is made to begin disposal in the WIPP or to terminate the project if regulatory compliance cannot be determined and demonstrated. Authorization to receive transuranic waste at the WIPP for the test phase is given by the WIPP LWA provided certain requirements are met

Project Strategy For The Remediation And Disposition Of Legacy Transuranic Waste At The Savannah River Site, South Carolina, USA

International Nuclear Information System (INIS)

Rodriguez, M.

2010-01-01

This paper discusses the Savannah River Site Accelerated Transuranic (TRU) Waste Project that was initiated in April of 2009 to accelerate the disposition of remaining legacy transuranic waste at the site. An overview of the project execution strategy that was implemented is discussed along with the lessons learned, challenges and improvements to date associated with waste characterization, facility modifications, startup planning, and remediation activities. The legacy waste was generated from approximately 1970 through 1990 and originated both on site as well as at multiple US Department of Energy sites. Approximately two thirds of the waste was previously dispositioned from 2006 to 2008, with the remaining one third being the more hazardous waste due to its activity (curie content) and the plutonium isotope Pu-238 quantities in the waste. The project strategy is a phased approach beginning with the lower activity waste in existing facilities while upgrades are made to support remediation of the higher activity waste. Five waste remediation process lines will be used to support the full remediation efforts which involve receipt of the legacy waste container, removal of prohibited items, venting of containers, and resizing of contents to fit into current approved waste shipping containers. Modifications have been minimized to the extent possible to meet the accelerated goals and involve limited upgrades to address life safety requirements, radiological containment needs, and handling equipment for the larger waste containers. Upgrades are also in progress for implementation of the TRUPACT III for the shipment of Standard Large Boxes to the Waste Isolation Pilot Plant, the US TRU waste repository. The use of this larger shipping container is necessary for approximately 20% of the waste by volume due to limited size reduction capability. To date, approximately 25% of the waste has been dispositioned, and several improvements have been made to the overall processing

Waste Receiving and Processing (WRAP) Facility Final Safety Analysis Report (FSAR)

Energy Technology Data Exchange (ETDEWEB)

TOMASZEWSKI, T.A.

2000-04-25

The Waste Receiving and Processing Facility (WRAP), 2336W Building, on the Hanford Site is designed to receive, confirm, repackage, certify, treat, store, and ship contact-handled transuranic and low-level radioactive waste from past and present U.S. Department of Energy activities. The WRAP facility is comprised of three buildings: 2336W, the main processing facility (also referred to generically as WRAP); 2740W, an administrative support building; and 2620W, a maintenance support building. The support buildings are subject to the normal hazards associated with industrial buildings (no radiological materials are handled) and are not part of this analysis except as they are impacted by operations in the processing building, 2336W. WRAP is designed to provide safer, more efficient methods of handling the waste than currently exist on the Hanford Site and contributes to the achievement of as low as reasonably achievable goals for Hanford Site waste management.

Waste Receiving and Processing (WRAP) Facility Final Safety Analysis Report (FSAR)

International Nuclear Information System (INIS)

TOMASZEWSKI, T.A.

2000-01-01

The Waste Receiving and Processing Facility (WRAP), 2336W Building, on the Hanford Site is designed to receive, confirm, repackage, certify, treat, store, and ship contact-handled transuranic and low-level radioactive waste from past and present U.S. Department of Energy activities. The WRAP facility is comprised of three buildings: 2336W, the main processing facility (also referred to generically as WRAP); 2740W, an administrative support building; and 2620W, a maintenance support building. The support buildings are subject to the normal hazards associated with industrial buildings (no radiological materials are handled) and are not part of this analysis except as they are impacted by operations in the processing building, 2336W. WRAP is designed to provide safer, more efficient methods of handling the waste than currently exist on the Hanford Site and contributes to the achievement of as low as reasonably achievable goals for Hanford Site waste management

Fuel burn-up distribution and transuranic nuclide contents produced at the first cycle operation of AP1000

International Nuclear Information System (INIS)

Jati Susilo; Jupiter Sitorus Pane

2016-01-01

AP1000 reactor core was designed with nominal power of 1154 MWe (3415 MWth), operated within life time of 60 years and cycle length of 18 months. For the first cycle, the AP1000 core uses three kinds of UO 2 enrichment, they are 2.35 w/o, 3.40 w/o and 4.45 w/o. Absorber materials such as ZrB 2 , Pyrex and Boron solution are used to compensate the excess reactivity at the beginning of cycle. In the core, U-235 fuels are burned by fission reaction and produce energy, fission products and new neutron. Because of the U-238 neutron absorption reaction, the high level radioactive waste of heavy nuclide transuranic such as Pu, Am, Cm and Np are also generated. They have a very long half life. The purpose of this study is to evaluate the result of fuel burn-up distribution and heavy nuclide transuranic contents produced by AP1000 at the end of first cycle operation (EOFC). Calculation of ¼ part of the AP1000 core in the 2 dimensional model has been done using SRAC2006 code with the module of COREBN/HIST. The input data called the table of macroscopic cross section, is calculated using module of PIJ. The result shows that the maximum fuel assembly (FA) burn-up is 27.04 GWD/MTU, that is still lower than allowed maximum burn-up of 62 GWD/MTU. Fuel loading position at the center/middle of the core will produce bigger burn-up and transuranic nuclide than one at the edges the of the core. The use of IFBA fuel just give a small effect to lessen the fuel burn-up and transuranic nuclide production. (author)

Experimental skin deposition of chromium on the hands following handling of samples of leather and metal

DEFF Research Database (Denmark)

Bregnbak, David; Thyssen, Jacob P.; Jellesen, Morten Stendahl

2016-01-01

Background: Chromium is an important skin sensitizer. Exposure to it has been regulated in cement, and recently in leather. Studies on the deposition of chromium ions on the skin as a result of handling different chromium-containing materials are sparse, but could improve the risk assessment...... of contact sensitization and allergic contact dermatitis caused by chromium. Objectives: To determine whether the handling of chromium-containing samples of leather and metal results in the deposition of chromium onto the skin. Methods: Five healthy volunteers participated. For 30 min, they handled samples...... of leather and metal known to contain and release chromium. Skin deposition of chromium was assessed with the acid wipe sampling technique. Results: Acid wipe sampling of the participants' fingers showed chromium deposition on the skin in all participants who had been exposed to leather (range 0.01–0.20 µg...

Distribution of transuranic elements in a freshwater pond ecosystem

International Nuclear Information System (INIS)

Emery, R.M.; Klopfer, D.C.

1976-01-01

During the past two years a unique study has been initiated on the Hanford Reservation concerning the ecological behavior of plutonium and americium in a freshwater environment. This study involves a waste pond which has been receiving occasional low-level plutonium processing wastes for about 30 years. The pond has a sufficiently established ecosystem to provide an excellent location for limnological characterization. In addition, the ecological distribution of plutonium and americium is being investigated. The purpose of this work is to explain plutonium and americium concentrations at specific ecological sites, important export routes out of the pond, and potential pathways to man. The pond is also highly enriched with nutrients, thus supporting a high level of algal and macrophyte production. Seston (30 percent diatoms) appears to be the principal concentrator of transuranics in the pond system. The major sink for plutonium and americium in this system is the sediments. Organic floc, overlaying the pond sediments, is also a major concentrator of transuranics in this system. Aside from the seston and floc, no other ecological components of the pond appear to have concentrations significantly greater than those of the sediment. Dragonfly larvae, watercress, and snails show concentrations which approximate those of the sediments but nearly all other food web components have levels of plutonium and americium which are lower than those of the sediments. Thus, plutonium and americium seem to be relatively immobile in the aquatic ecosystem. However, the role of algae as a potential mechanism for the long-range ecological transport of plutonium and americium will receive additional attention

Interstitial water studies on Irish Sea sediments and their relevance to the fate of transuranic nuclides in the marine environment

International Nuclear Information System (INIS)

Harvey, B.R.

1981-01-01

This paper describes the physico-chemical conditions existing in the interstitial waters of sediments in contaminated areas of the Irish Sea, which provide valuable information on the sedimentary environment into which radioactive waste products become incorporated. It is recommended that these measurements be made in areas where transuranic behaviour can be determined, which then would allow useful predictions to be made concerning the possible behaviour of transuranics in other, uncontaminated, environments, if these environments can be physico-chemically correlated in the same way. (author)

Compliance among soft contact lens wearers.

Science.gov (United States)

Kuzman, Tomislav; Kutija, Marija Barisić; Masnec, Sanja; Jandroković, Sonja; Mrazovac, Danijela; Jurisić, Darija; Skegro, Ivan; Kalauz, Miro; Kordić, Rajko

2014-12-01

Contact lens compliance is proven to be crucial for preventing lens wear-related complications because of the interdependence of the steps in lens care regime and their influence on lens system microbial contamination. Awareness of the patients' lens handling compliance as well as correct recognition of non-compliant behaviours is the basis for creating more targeted strategies for patient education. The aim of this study was to investigate compliance among soft contact lens (SCL) wearers in different aspects of lens care handling and wearing habits. In our research 50 asymptomatic lens wearers filled out a questionnaire containing demographic data, lens type, hygiene and wearing habits, lenses and lens care system replacement schedule and self-evaluation of contact lens handling hygiene. We established criteria of compliance according to available manufacturer's recommendations, prior literature and our clinical experience. Only 2 (4%) of patients were fully compliant SCL wearers. The most common non-compliant behaviours were insufficient lens solution soaking time (62%), followed by failure to daily exchange lens case solution and showering while wearing lenses. 44% of patients reported storing lenses in saline solution. Mean lens storage case replacement was 3.6 months, with up to 78% patients replacing lens case at least once in 3 months. Average grade in self evaluating level of compliance was very good (4 +/- 0.78) (from 1-poor level of hygiene to 5-great level of hygiene). Lens wearers who reported excessive daily lens wear and more than 10 years of lens wearing experience were also found to be less compliant with other lens system care procedures. (t = -2.99, df=47, p rate, self grading was relatively high. Therefore, these results indicate the need for patient education and encouragement of better lens wearing habits and all of the lens maintenance steps at each patient visit.

Nondestructive characterization of low-level transuranic waste

International Nuclear Information System (INIS)

Barna, B.A.; Reinhardt, W.W.

1981-10-01

The use of nondestructive evaluation (NDE) methods is proposed for characterization of transuranic (TRU) waste stored at the Radioactive Waste Management Complex. These NDE methods include real-time x-ray radiography, real-time neutron radiography, x-ray and neutron computed tomography, thermal imaging, container weighing, visual examination, and acoustic measurements. An integrated NDE system is proposed for characterization and certification of TRU waste destined for eventual shipment to the Waste Isolation Pilot Plant in New Mexico. Methods for automating both the classification waste and control of a complete nondestructive evaluation/nondestructive assay system are presented. Feasibility testing of the different NDE methods, including real-time x-ray radiography, and development of automated waste classification techniques are covered as part of a five year effort designed to yield a production waste characterization system

Puncture panel optimization

International Nuclear Information System (INIS)

Glass, R.E.; Longenbaugh, R.S.

1986-01-01

Sandia National Laboratories developed the TRansUranic PACkage Transporter (TRUPACT) to transport defense contact-handled transuranic wastes. The package has been designed to meet the normal and hypothetical accident conditions in 10CFR71 which includes the demonstrated ability to survive a 1-meter drop onto a mild steel pin. The puncture protection is provided by puncture resistant panels. In conjunction with the development of TRUPACT, a series of experiments has been conducted to reduce the weight of the puncture resistant panels. The initial scoping tests resulted in a preliminary design incorporating 30 layers of Kevlar. This design has been shown to meet the regulatory puncture test. To reduce the weight of this panel, subscale tests were conducted on panels utilizing Kevlar yarns with varying mass per unit length (denier) as well as different resins. This paper reviews the testing undertaken in the original panel development and discusses the results obtained from the recent subscale and full-scale optimization tests

Acid decomposition processing system for radioactive wastes

International Nuclear Information System (INIS)

Oomine, Toshimitsu.

1984-01-01

Purpose: To perform plutonium recovery at a low energy consumption irrespective of the plutonium density within the wastes. Method: In a decomposing and volume-reducing device for combustible or less combustible wastes containing transuranic elements using an acid, the wastes are in contact with nitric acid before feeding to a reactor. Then, the transuranic elements are transferred into the nitric acid, which is then in contact with ion exchange resins. After adsorbing the transuranic elements to the ion exchange resins, the nitric acid removed with the transuranic elements is caused to flow into a reaction vessel or heating vessel and used as a decomposing and oxidizing agent. (Seki, T.)

Safety evaluation report of the Waste Isolation Pilot Plant safety analysis report: Contact-handled transuranic waste disposal operations

International Nuclear Information System (INIS)

1997-02-01

DOE 5480.23, Nuclear Safety Analysis Reports, requires that the US Department of Energy conduct an independent, defensible, review in order to approve a Safety Analysis Report (SAR). That review and the SAR approval basis is documented in this formal Safety Evaluation Report (SER). This SER documents the DOE's review of the Waste Isolation Pilot Plant SAR and provides the Carlsbad Area Office Manager, the WIPP SAR approval authority, with the basis for approving the safety document. It concludes that the safety basis documented in the WIPP SAR is comprehensive, correct, and commensurate with hazards associated with planned waste disposal operations

RISK FACTORS FOR CONTACT LENS COMPLICATIONS

Directory of Open Access Journals (Sweden)

Mirna Štabuc Šilih

2016-04-01

Full Text Available Contact lenses are freely available without professional examination and fitting, as well as without adequate introduction and instructions on handling, disinfection and storage. Contact lenses may have physiological, metabolic and anatomic effect on the eyes, which is manifested both on the eyelids, lacrimal film, conjunctiva and in all layers of the cornea - the epithelium, stroma and the endothelium. We can see these complications too often at our everyday work. The purpose of this paper is to draw attention to the potential complications due to inappropriate use of contact lenses.Contact lenses are otherwise a safe and effective method of correcting visual acuity; they are also useful for therapeutic purposes. Complications related to contact lenses wear could be largely avoided with an appropriate professional approach and the compliance of contact lens wearers. It is important to discuss with patients their medical history, their desires and expectations, their working and living environment; followed by professional examination of patients and appropriate fitting of contact lenses. Patients should receive detailed oral and written instructions and be subscribed to regular checks. But unfortunately, all this is not enough, if patients do not comply every day with given instructions.

Treatment needs for greater-than-Class C low-level wastes

International Nuclear Information System (INIS)

Ross, W.A.; Brouns, R.A.; Burkholder, H.C.

1988-01-01

Greater-than-Class C (GTCC) radioactive wastes are those low-level wastes that exceed the 10CFR61 limits for shallow-land burial but are not within the historical definition of high-level wastes (i.e., spent fuel and first-cycle reprocessing wastes). The GTCC category can include all transuranic (TRU) wastes, although for the purposes of this paper, contact-handled defense TRU wastes are excluded because of the major efforts in the past decade to prepare them for disposal at the Waste Isolation Pilot Plant (WIPP). Thus, the GTCC category includes all high-activity and remote-handled TRU wastes regardless of origin. This paper defines the need for treatment of existing and projected GTCC low-level radioactive wastes in the United States. The sources, characteristics, treatment considerations, and methods for treatment are reviewed

Waste Management Facilities Cost Information for transportation of radioactive and hazardous materials. Revision 1

International Nuclear Information System (INIS)

Feizollahi, F.; Shropshire, D.; Burton, D.

1994-09-01

This report contains transportation costs for most types of DOE waste streams: low-level waste (LLW), mixed low-level waste (MLLW), alpha LLW and alpha MLLW, greater-than-Class C (GTCC) LLW and DOE equivalent waste, transuranic waste (TRU), spent nuclear fuel (SNF), and hazardous waste. Unit rates for transportation of contact-handled ( 200 mrem/hr contact dose) radioactive waste have been estimated previously, and a summary has been included in earlier WMFCI reports. In order to have a single source for obtaining transportation cost for all radioactive waste, the transportation costs for the contact- and remote-handled wastes are repeated in this report. Land transportation of radioactive and hazardous waste is subject to regulations promulgated by DOE, the US Department of Transportation (DOT), the US Nuclear Regulatory Commission (NRC), and state and local agencies. The cost estimates in this report assume compliance with applicable regulations. It should be noted that the trend is toward greater restrictions on transportation of radioactive waste (e.g., truck or rail car speed, shipping route, security escort, and personnel training requirements), which may have a significant impact on future costs

Input of transuranic elements through rivers into the Mediterranean Sea

International Nuclear Information System (INIS)

Fukai, R.; Ballestra, S.; Thein, M.

1981-01-01

Measurements of 137 Cs, 238 Pu, sup(239+240)Pu and 241 Am were carried out on river water as well as its suspended matter collected seasonally in 1977 from two Mediterranean rivers, the Var and the Rhone. The results show that although the concentrations of the soluble fractions of these radionuclides are higher in the Rhone than in the Var, even the elevated concentrations of soluble 137 Cs (approximately 40 fCi.ltr -1 ) and sup(239+240)Pu (approximately 0.1 fCi.ltr -1 ) in the Rhone are much lower than the average concentrations of these nuclides in Mediterranean surface waters. On the other hand, the concentrations of the nuclides measured in suspended matter are roughly an order of magnitude higher in the Rhone than in the Var. Based on the results of measurements on the two rivers, and assuming that the annual average concentrations of the radionuclides in the Var and the Rhone respectively represent those in radiologically uncontaminated and contaminated Mediterranean rivers, the total inputs of 137 Cs, 238 Pu, sup(239+240)Pu and 241 Am through rivers into the Mediterranean Sea have been estimated. Comparison of these estimated values with the inputs of fallout radionuclides by rain indicates that although local accumulation of transuranic nuclides may be observed on sediments taken from some limited estuarine areas, the geochemical behaviour of transuranic elements in the Mediterranean, as a whole, is exclusively governed today by the fallout input of these elements. (author)

Radiological, physical, and chemical characterization of transuranic wastes stored at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Apel, M.L.; Becker, G.K.; Ragan, Z.K.; Frasure, J.; Raivo, B.D.; Gale, L.G.; Pace, D.P.

1994-03-01

This document provides radiological, physical and chemical characterization data for transuranic radioactive wastes and transuranic radioactive and hazardous (i.e., mixed) wastes stored at the Idaho National Engineering Laboratory and considered for treatment under the Private Sector Participation Initiative Program (PSPI). Waste characterization data are provided in the form of INEL Waste Profile Sheets. These documents provide, for each content code, information on waste identification, waste description, waste storage configuration, physical/chemical waste composition, radionuclide and associated alpha activity waste characterization data, and hazardous constituents present in the waste. Information is provided for 139 waste streams which represent an estimated total volume of 39,380 3 corresponding to a total mass of approximately 19,000,000 kg. In addition, considerable information concerning alpha, beta, gamma, and neutron source term data specific to Rocky Flats Plant generated waste forms stored at the INEL are provided to assist in facility design specification

Low-level determination of transuranic elements in marine environment samples

International Nuclear Information System (INIS)

Ballestra, S.; Holm, E.; Fukai, R.

1978-01-01

The procedures developed and currently employed in the Monaco Laboratory for determining transuranic elements in seawater, marine sediments and organisms are described and discussed. While the standard anion-exchange procedure from the hydrochloric acid medium is used for the separation of plutonium isotopes from americium, purification of americium and curium is achieved by an ion-exchange sorption from the methanol-nitric acid medium, followed by an elution with the methanol-hydrochloric acid mixture. Satisfactory clean-up of plutonium as well as americium and curium can be achieved by applying the described procedures. (author)

Risk evaluations of transuranic waste at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Smith, T.H.; Keneshea, F.J.

1980-01-01

Approximately 75% of the defense low-level transuranic (TRU) waste stored in the United States and 25% of the buried TRU waste is located at the Idaho National Engineering Laboratory (INEL). Studies have been performed to identify and evaluate technical alternatives for the long-term management of this waste. (The alternatives range from leaving the waste in place as is to reviewing, processing, and shipping it to an offsite geological repository.) Among the evalations that have been performed were preliminary risk evaluations. The dose commitment and risk of hypothetical, near-term, accidental or uncontrolled releases of radionuclides have been evaluated for each alternative. The following potential causes of radionuclide release have been studied: process and handling accidents, shipping accidents, natural events (e.g., earthquakes), man-caused events (e.g., airplane crashes), and future intrusion by individuals or small populations after loss of societal control over the waste. The hypothetical releases have been evaluated, in terms of dose commitment and (if pertinent) probability and risk, for all operational steps making up each concept. The dominant scanerios in terms of near-term risk are (1) lava flow up through or over the waste, leading to airbone releases; (2) an explosion or a criticality accident in the waste-processing facility; and (3) a tornado strike or a fire during waste retrieval. The dominant long-term releases are (1) volcanic action; and (2) intrusion of people on the waste site.Although substantial dose commitments to individual members of the public were calculated for the lava flow and intrusion scenarios, no prompt health effects would be expected from the exposures. The effects would be in the form of a slightly increased likelihood of latent cancer induction

Pizza makers' contact dermatitis.

Science.gov (United States)

Lembo, Serena; Lembo, Claudio; Patruno, Cataldo; Balato, Anna; Balato, Nicola; Ayala, Fabio

2014-01-01

Contact eczema to foods, spices, and food additives can occur in occupational and nonoccupational settings in those who grow, handle, prepare, or cook food. Pizza is one of the most eaten foods in every continent, and pizza making is a common work in many countries. We aimed to evaluate the occurrence and the causes of contact dermatitis in pizza makers in Naples. We performed an observational study in 45 pizza makers: all the enrolled subjects had to answer a questionnaire designed to detect personal history of respiratory or cutaneous allergy, atopy; work characteristics and timing were also investigated. Every subject attended the dermatology clinic for a complete skin examination, and when needed, patients were patch tested using the Italian baseline series of haptens integrated with an arbitrary pizza makers series. Our results reported that 13.3% of the enrolled pizza makers (6/45) presented hand eczema, and that 8.9% (4/45) were affected by occupational allergic contact dermatitis. Diallyl disulfide and ammonium persulfate were the responsible substances. Performing patch tests in pizza makers and food handlers affected by hand contact dermatitis is useful. We propose a specific series of haptens for this wide working category.

Technologies for recovery of transuranics and immobilization of non-high-level wastes

International Nuclear Information System (INIS)

Richardson, G.L.

1976-06-01

This paper supplements the preceding Symposium paper on ''Treatment Technologies for Non-High-Level Wastes (U.S.A.)'' by C. R. Cooley and D. E. Clark (HEDL-SA-851), and covers the additional treatment technologies in use and under development for recovering transuranics and immobilizing non-high-level wastes for transportation and storage. Methods used for nondestructive assay (NDA) of TRU elements in non-high-level wastes are also discussed briefly

FY85 Program plan for the Defense Transuranic Waste Program (DTWP)

International Nuclear Information System (INIS)

1984-11-01

The Defense TRU Waste Program (DTWP) is the focal point for the Department of Energy in national planning, integration, and technical development for TRU waste management. The scope of this program extends from the point of TRU waste generation through delivery to a permanent repository. The TRU program maintains a close interface with repository development to ensure program compatibility and coordination. The defense TRU program does not directly address commercial activities that generate TRU waste. Instead, it is concerned with providing alternatives to manage existing and future defense TRU wastes. The FY85 Program Plan is consistent with the Defense TRU Waste Program goals and objectives stated in the Defense Transuranic Waste Program Strategy Document, January 1984. The roles of participants, the responsibilities and authorities for Research and Development (R and D), the organizational interfaces and communication channels for R and D and the establishment of procedures for planning, reporting, and budgeting of all R and D activities meet requirements stated in the Technical Management Plan for the Transuranic Waste Management Program. The Program Plan is revised as needed. The work breakdown structure is reflected graphically immediately following the Administration section and is described in the subsequent narrative. Detailed budget planning (i.e., programmatic funding and capital equipment) is presented for FY85; outyear budget projections are presented for future years

Transuranic element pathways to man

International Nuclear Information System (INIS)

Bennett, B.G.

1976-01-01

Transfer to man of transuranic element contamination may occur by the inhalation or ingestion pathways. The measurements of globally dispersed fall-out radioactivity have provided pertinent data on the environmental behaviour of plutonium. Additional data may eventually become available for americium. From the measured and inferred concentrations of fall-out plutonium, the inhalation intake has been determined and the ICRP Task Group lung model used to estimate deposition in the lung and transfer to other body organs. The computed body burden reached a maximum of 4pCi in 1964 and is currently about 2.5pCi. A complete diet sampling has been conducted to determine ingestion intake. Plutonium concentration in food ranged from 0.01pCi/kg in shellfish to undetected (less than 0.0003pCi/kg) in milk. Annual intake in total diet is estimated to have been 1.6pCi in 1972. Low uptake by the gastrointestinal tract makes contribution to organ burdens from ingestion negligible. Long-term pathway considerations include plant uptake from the cumulative deposit in soil and resuspension. Downward movement in soil may limit the significance of these long-term pathway components. (author)

Planning a transportation system for US Defense Transuranic waste

International Nuclear Information System (INIS)

Gilbert, K.V.; Hurley, J.D.; Smith, L.J.; McFadden, M.H.; Raudenbush, M.H.; Fedie, M.L.

1983-05-01

The development and planning of a transportation system for US Department of Energy (USDOE) Defense Transuranic (TRU) waste has required the talents and expertise of many people. Coordination activities, design activities, fabrication, research and development, operations, and transportation are but a few of the areas around which this system is built. Due to the large number of organizations, regulations and personalities the planning task becomes extremely complex. The intent of this paper is to discuss the steps taken in planning this system, to identify the various organizations around which this system is designed, and to discuss program progress to date, scheduling, and future plans. 9 figures, 1 table

Gas generation from transuranic waste degradation: an interim assessment

International Nuclear Information System (INIS)

Molecke, M.A.

1979-10-01

A review of all available, applicable data pertaining to gas generation from the degradation of transuranic waste matrix material and packaging is presented. Waste forms are representative of existing defense-related TRU wastes and include cellulosics, plastics, rubbers, concrete, process sludges, and mild steel. Degradation mechanisms studied were radiolysis, thermal, bacterial, and chemical corrosion. Gas generation rates are presented in terms of moles of gas produced per year per drum, and in G(gas) values for radiolytic degradation. Comparison of generation rates is made, as is a discussion of potential short- and long-term concerns. Techniques for reducing gas generation rates are discussed. 6 figures, 10 tables

Planning a transportation system for US defense transuranic waste

International Nuclear Information System (INIS)

Gilbert, K.V.; Hurley, J.D.; Smith, L.J.; McFadden, M.H.; Raudenbush, M.H.; Fedie, M.L.

1983-01-01

The development and planning of a transportation system for US Department of Energy (USDOE) Defense Transuranic (TRU) waste has required the talents and expertise of many people. Coordination activities, design activities, fabrication, research and development, operations, and transportation are but a few of the areas around which this system is built. Due to the large number of organizations, regulations and personalities the planning task becomes extremely complex. The intent of this paper is to discuss the steps taken in planning this system, to identify the various organizations around which this system is designed, and to discuss program progress to date, scheduling, and future plans

Physical Properties of Hanford Transuranic Waste. Final Report

International Nuclear Information System (INIS)

Berg, John C.

2010-01-01

The research described herein was undertaken to provide needed physical property descriptions of the Hanford transuranic tank sludges under conditions that might exist during retrieval, treatment, packaging and transportation for disposal. The work addressed the development of a fundamental understanding of the types of systems represented by these sludge suspensions through correlation of the macroscopic rheological properties with particle interactions occurring at the colloidal scale in the various liquid media. The results of the work have advanced existing understanding of the sedimentation and aggregation properties of complex colloidal suspensions. Bench scale models were investigated with respect to their structural, colloidal and rheological properties that should be useful for the development and optimization of techniques to process the wastes at various DOE sites.

Maria Goeppert Mayer's Theoretical Work on Rare-Earth and Transuranic Elements

OpenAIRE

Wang, Frank Y.

2008-01-01

After the discovery of element 93 neptunium by Edwin McMillan and Philip H. Abelson in 1941, Maria Goeppert Mayer applied the Thomas-Fermi model to calculate the electronic configuration of heavy elements and predicted the occurrence of a second rare-earth series in the vicinity of elements 91 or 92 extending to the transuranic elements. Mayer was motivated by Enrico Fermi, who was at the time contemplating military uses of nuclear energy. Historical development of nuclear science research le...

Measurement accuracy of a stressed contact lens during its relaxation period

Science.gov (United States)

Compertore, David C.; Ignatovich, Filipp V.

2018-02-01

We examine the dioptric power and transmitted wavefront of a contact lens as it releases its handling stresses. Handling stresses are introduced as part of the contact lens loading process and are common across all contact lens measurement procedures and systems. The latest advances in vision correction require tighter quality control during the manufacturing of the contact lenses. The optical power of contact lenses is one of the critical characteristics for users. Power measurements are conducted in the hydrated state, where the lens is resting inside a solution-filled glass cuvette. In a typical approach, the contact lens must be subject to long settling times prior to any measurements. Alternatively, multiple measurements must be averaged. Apart from potential operator dependency of such approach, it is extremely time-consuming, and therefore it precludes higher rates of testing. Comprehensive knowledge about the settling process can be obtained by monitoring multiple parameters of the lens simultaneously. We have developed a system that combines co-aligned a Shack-Hartmann transmitted wavefront sensor and a time-domain low coherence interferometer to measure several optical and physical parameters (power, cylinder power, aberrations, center thickness, sagittal depth, and diameter) simultaneously. We monitor these parameters during the stress relaxation period and show correlations that can be used by manufacturers to devise methods for improved quality control procedures.

Sources, Speciation and Mobility of Plutonium and Other Transuranics in the Groundwater at the Savannah River Site

International Nuclear Information System (INIS)

Buesseler, Ken O.

2005-01-01

This annual report summarizes work to date on our EMSP project: ?Sources, Speciation and Mobility of Plutonium and Other Transuranics in the Groundwater at the Savannah River Site (Sept. 2003-Sept. 2006). Our research focus is to further evaluate the sources and fate of Pu and other transuranics in groundwater at the Savannah River Site (SRS). Our overarching goal is to understand Pu speciation and mobility well enough to support safe remediation, containment and long term stewardship at any site with transuranic wastes and sources. Methods developed under prior funding for the determination Pu isotopes, oxidation state and size fractionation in groundwater are providing the best direct evidence for rejecting or not, hypotheses concerning whether colloids enhance the transport of Pu and other transuranics in groundwater. Survey samples collected in the fall of 2003 from F-area well FSB 78 had a 240/239 Pu atom ratio 7.087 +/-0.048 and reflects the continued presences of decayed 244Cm. In October 2004, we returned to the F-area and completed comprehensive field sampling of 7 wells. Field experiments included 6 different extraction rates at well 92D to test sensitivity to artifacts related to well pumping rates, and an aging experiment to evaluate Pu behavior by re-oxidation of reducing groundwater. Sampling of Pond B was included in the site visit to explore unique conditions of redox potential on Pu within the pond. To date, more than 70 Pu redox and whole water samples have been processed and are awaiting analysis at PNNL. Also, five samples from our 1998 visit are undergoing chemistry at PNNL to directly measure Cm with analysis of 2004 samples to follow. Work is continuing to evaluate particle affinity under controlled conditions and a site specific groundwater transport model which we will apply to our lab and field data to obtain a better understanding of the importance of these processes on Pu transport

Final Environmental Impact Statement for Treating Transuranic (TRU)/Alpha Low-level Waste at the Oak Ridge National Laboratory Oak Ridge, Tennessee

Energy Technology Data Exchange (ETDEWEB)

N/A

2000-06-30

The DOE proposes to construct, operate, and decontaminate/decommission a TRU Waste Treatment Facility in Oak Ridge, Tennessee. The four waste types that would be treated at the proposed facility would be remote-handled TRU mixed waste sludge, liquid low-level waste associated with the sludge, contact-handled TRU/alpha low-level waste solids, and remote-handled TRU/alpha low-level waste solids. The mixed waste sludge and some of the solid waste contain metals regulated under the Resource Conservation and Recovery Act and may be classified as mixed waste. This document analyzes the potential environmental impacts associated with five alternatives--No Action, the Low-Temperature Drying Alternative (Preferred Alternative), the Vitrification Alternative, the Cementation Alternative, and the Treatment and Waste Storage at Oak Ridge National Laboratory (ORNL) Alternative.

Results of HWVP transuranic process waste treatment laboratory and pilot-scale filtration tests using specially ground zeolite

International Nuclear Information System (INIS)

Eakin, D.E.

1996-03-01

Process waste streams from the Hanford Waste Vitrification Plant (HWVP) may require treatment for cesium, strontium, and transuranic (TRU) element removal in order to meet criteria for incorporation in grout. The approach planned for cesium and strontium removal is ion exchange using a zeolite exchanger followed by filtration. Filtration using a pneumatic hydropulse filter is planned to remove TRU elements which are associated with process solids and to also remove zeolite bearing the cesium and strontium. The solids removed during filtration are recycled to the melter feed system to be incorporated into the HWVP glass product. Fluor Daniel, Inc., the architect-engineering firm for HWVP, recommended a Pneumatic Hydropulse (PHP) filter manufactured by Mott Metallurgical Corporation for use in the HWVP. The primary waste streams considered for application of zeolite contact and filtration are melter off-gas condensate from the submerged bed scrubber (SBS), and equipment decontamination solutions from the Decontamination Waste Treatment Tank (DWTT). Other waste streams could be treated depending on TRU element and radionuclide content. Laboratory and pilot-scale filtration tests were conducted to provide a preliminary assessment of the adequacy of the recommended filter for application to HWVP waste treatment

WIPP Status and Plans - 2013 - 13379

Energy Technology Data Exchange (ETDEWEB)

Nelson, R.A.; Franco, J. [U.S. Department of Energy, PO Box 3090, Carlsbad, NM 88220 (United States)

2013-07-01

An up-to-date look at the many aspects of America's only deep geologic long-lived radioactive waste repository is presented in this paper. WIPP's mission includes coordination of all Department of Energy (DOE) sites to prepare, package and characterize defense transuranic waste for final shipment and emplacement in WIPP. The Waste Isolation Pilot Plant (WIPP) is completing its 14. year of operations. Five of the ten planned disposal panels have been filled and sealed from ventilation, with about half of the legislated volume capacity consumed. About 11,000 shipments have been made successfully, traveling more than 40 million kilometers across the nation's highways. A fleet of new Type B shipping packages, the TRUPACT-III, has been added to the transportation capability, with an ongoing campaign to de-inventory large waste items from the Savannah River Site, while minimizing size reduction and repackaging. A new shipping and emplacement method for remote handled waste in shielded containers has been approved for disposal, and will significantly improve operational efficiency. Remote handled waste packaged in these shielded containers will be shipped, handled and emplaced as contact handled waste. Also described is a new criticality control over-pack container, which will improve efficiency when shipping high fissile-content waste streams consisting of Special Nuclear Material declared as waste from nuclear weapons sites. The paper describes the importance of the infrastructure at WIPP to ensure disposal site availability for defense transuranic waste sites across the weapons complex. With the facility reaching its original design lifetime, there are many infrastructure maintenance and improvements being planned and performed. (authors)

Contact pressure measurement in hand tool evaluation studies

NARCIS (Netherlands)

Kuijt-Evers, L.F.M.; Bosch, T.

2006-01-01

In hand tool evaluation studies, several objective measurements are used. Grip force distribution and grip force are important as they give feedback about the force which has to be performed with the hand on the handle. A measurement technique -which is related to grip force measurement- is contact

Limits for the burial of the Department of Energy transuranic wastes

Energy Technology Data Exchange (ETDEWEB)

Healy, J.W.; Rodgers, J.C.

1979-01-15

Potential limits for the shallow earth burial of transuranic elements were examined by simplified models of the individual pathways to man. Pathways examined included transport to surface steams, transport to ground water, intrusion, and people living on the burial ground area after the wastes have surfaced. Limits are derived for each pathway and operational limits are suggested based upon a dose to the organ receiving the maximum dose rate of 0.5 rem/y after 70 years of exposure for the maximum exposed individual.

Limits for the burial of the Department of Energy transuranic wastes

International Nuclear Information System (INIS)

Healy, J.W.; Rodgers, J.C.

1979-01-01

Potential limits for the shallow earth burial of transuranic elements were examined by simplified models of the individual pathways to man. Pathways examined included transport to surface steams, transport to ground water, intrusion, and people living on the burial ground area after the wastes have surfaced. Limits are derived for each pathway and operational limits are suggested based upon a dose to the organ receiving the maximum dose rate of 0.5 rem/y after 70 years of exposure for the maximum exposed individual

Los Alamos Transuranic Waste Size Reduction Facility

International Nuclear Information System (INIS)

Harper, J.; Warren, J.

1987-06-01

The Los Alamos Transuranic (TRU) Waste Size Reduction Facility (SRF) is a production oriented prototype. The facility is operated to remotely cut and repackage TRU contaminated metallic wastes (e.g., glove boxes, ducting and pipes) for eventual disposal at the Waste Isolation Pilot Plant (WIPP) near Carlsbad, New Mexico. The resulting flat sections are packaged into a tested Department of Transportation Type 7A metal container. To date, the facility has successfully processed stainless steel glove boxes (with and without lead shielding construction) and retention tanks. We have found that used glove boxes generate more cutting fumes than do unused glove boxes or metal plates - possibly due to deeply embedded chemical residues from years of service. Water used as a secondary fluid with the plasma arc cutting system significantly reduces visible fume generation during the cutting of used glove boxes and lead-lined glove boxes. 2 figs., 1 tab

On contact modelling in isogeometric analysis

Science.gov (United States)

Cardoso, R. P. R.; Adetoro, O. B.

2017-11-01

IsoGeometric Analysis (IGA) has proved to be a reliable numerical tool for the simulation of structural behaviour and fluid mechanics. The main reasons for this popularity are essentially due to: (i) the possibility of using higher order polynomials for the basis functions; (ii) the high convergence rates possible to achieve; (iii) the possibility to operate directly on CAD geometry without the need to resort to a mesh of elements. The major drawback of IGA is the non-interpolatory characteristic of the basis functions, which adds a difficulty in handling essential boundary conditions and makes it particularly challenging for contact analysis. In this work, the IGA is expanded to include frictionless contact procedures for sheet metal forming analyses. Non-Uniform Rational B-Splines (NURBS) are going to be used for the modelling of rigid tools as well as for the modelling of the deformable blank sheet. The contact methods developed are based on a two-step contact search scheme, where during the first step a global search algorithm is used for the allocation of contact knots into potential contact faces and a second (local) contact search scheme where point inversion techniques are used for the calculation of the contact penetration gap. For completeness, elastoplastic procedures are also included for a proper description of the entire IGA of sheet metal forming processes.

Test plan for demonstration of Rapid Transuranic Monitoring Laboratory

International Nuclear Information System (INIS)

McIsaac, C.V.; Sill, C.W.; Gehrke, R.J.; Killian, E.W.; Watts, K.D.

1993-06-01

This plan describes tests to demonstrate the capability of the Rapid Transuranic Monitoring Laboratory (RTML) to monitor airborne alpha-emitting radionuclides and analyze soil, smear, and filter samples for alpha- and gamma-emitting radionuclides under field conditions. The RTML will be tested during June 1993 at a site adjacent to the Cold Test Pit at the Radioactive Waste Management Complex at the Idaho National Engineering Laboratory. Measurement systems installed in the RTML that will be demonstrated include two large-area ionization chamber alpha spectrometers, an x-ray/gamma-ray spectrometer, and four alpha continuous air monitors. Test objectives, requirements for data quality, experimental apparatus and procedures, and safety and logistics issues are described

Hydrogen explosion testing with a simulated transuranic drum

International Nuclear Information System (INIS)

Dykes, K.L.; Meyer, M.L.

1990-01-01

Transuranic (TRU) waste generated at the Savannah River Site (SRS) is currently stored onsite for future retrieval and permanent disposal at the Waste Isolation Pilot Plant (WIPP). Some of the TRU waste is stored in vented 210-liter (55-gallon) drums and consists of gloves, wipes, plastic valves, tools, etc. Gas generation caused by radiolysis and biodegradation of these organic waste materials may produce a flammable hydrogen-air mixture (>4% v/v) in the multi-layer plastic waste bags. Using a worst case scenario, a drum explosion test program was carried out to determine the hydrogen concentration necessary to cause removal of the drum lid. Test results indicate an explosive mixture up to 15% v/v of hydrogen can be contained in an SRS TRU drum without total integrity failure via lid removal

Contact dermatitis caused by tulips: identification of contact sensitizers in tulip workers of Kashmir Valley in North India.

Science.gov (United States)

Hassan, Iffat; Rasool, Farhan; Akhtar, Saniya; Kamili, Afifa; Rather, Parvaiz; Kanth, Raihana; Bhat, Yasmeen; Rather, Shagufta; Mubashir, Syed; Yaseen, Atiya; Bashir, Safia

2018-01-01

Tulip, belonging to the genus Tulipa and family Liliaceae, is a spring-blooming perennial that grows from bulbs. Owing to manual handling, contact dermatitis can occur in professionals at any stage of the growth cycle of the tulip plant. To determine the clinical pattern of contact dermatitis resulting from tulip plant cultivation, and to assess contact allergy in workers coming into contact with this plant. One hundred and sixty-four tulip workers were screened, and 48 patients with suspected contact dermatitis were patch tested with 39 allergens, including haptens from the Indian baseline series, a plant series, and extracts from different parts of the tulip plant. Thirty-nine positive patch test reactions were observed in 21 patients. Seventeen patients showed positive reactions to either α-methylene-γ-butyrolactone or to tulip plant extract. Clinical relevance was observed for 13 of 17 positive patch test reactions. Contact dermatitis is an important health hazard in workers dealing with tulip bulbs. Further studies to identify and isolate other possible tulip allergens, and to quantify the amounts of allergens in different parts of the tulip plant, are recommended. © 2017 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

Low temperature setting iron phosphate ceramics as a stabilization and solidification agent for incinerator ash contaminated with transuranic and RCRA metals

International Nuclear Information System (INIS)

Medvedev, P.G.; Hansen, M.; Wood, E.L.; Frank, S.M.; Sidwell, R.W.; Giglio, J.J.; Johnson, S.G.; Macheret, J.

1997-01-01

Incineration of combustible Mixed Transuranic Waste yields an ash residue that contains oxides of Resource Conservation and Recovery Act (RCRA) and transuranic metals. In order to dispose of this ash safely, it has to be solidified and stabilized to satisfy appropriate requirements for repository disposal. This paper describes a new method for solidification of incinerator ash, using room temperature setting iron phosphate ceramics, and includes fabrication procedures for these waste forms as well as results of the MCC-1 static leach test, XRD analysis, scanning electron microscopy studies and density measurements of the solidified waste form produced

Handling chemotherapy drugs-Do medical gloves really protect?

Science.gov (United States)

Landeck, Lilla; Gonzalez, Ernesto; Koch, Olaf Manfred

2015-10-15

Due to their potential mutagenic, carcinogenic and teratogenic effects occupational exposure to chemotherapy drugs should be kept to a minimum. Utilization of personnel protective devices, especially the use of protective medical gloves, is a mainstay to avoid skin contact. The choice of appropriate gloves is of outstanding importance. For optimal protection in the oncology setting it is essential to establish general guidelines evaluating appropriate materials and defining quality standards. Establishing these guidelines can facilitate better handling and avoid potential hazards and late sequelae. In Europe there are no specific requirements or test methodologies for medical gloves used in the oncology environment. The implementation of uniform standards for gloves used while handling chemotherapy drugs would be desirable. In contrast, in the US medical gloves used to handle chemotherapy drugs have to fulfill requirements according to the ASTM International (American Society of Testing and Materials) standard D 6978-05. Nitrile or natural rubber latex is a preferred basic glove material, while vinyl is considered inappropriate because of its generally increased permeability. For extended exposure to chemotherapy drugs, double gloving, the use of thicker gloves and the frequent change of gloves increases their protective power. © 2014 UICC.

Safety analysis report for packaging (onsite) transuranic performance demonstration program sample packaging

International Nuclear Information System (INIS)

Mccoy, J.C.

1997-01-01

The Transuranic Performance Demonstration Program (TPDP) sample packaging is used to transport highway route controlled quantities of weapons grade (WG) plutonium samples from the Plutonium Finishing Plant (PFP) to the Waste Receiving and Processing (WRAP) facility and back. The purpose of these shipments is to test the nondestructive assay equipment in the WRAP facility as part of the Nondestructive Waste Assay PDP. The PDP is part of the U. S. Department of Energy (DOE) National TRU Program managed by the U. S. Department of Energy, Carlsbad Area Office, Carlsbad, New Mexico. Details of this program are found in CAO-94-1045, Performance Demonstration Program Plan for Nondestructive Assay for the TRU Waste Characterization Program (CAO 1994); INEL-96/0129, Design of Benign Matrix Drums for the Non-Destructive Assay Performance Demonstration Program for the National TRU Program (INEL 1996a); and INEL-96/0245, Design of Phase 1 Radioactive Working Reference Materials for the Nondestructive Assay Performance Demonstration Program for the National TRU Program (INEL 1996b). Other program documentation is maintained by the national TRU program and each DOE site participating in the program. This safety analysis report for packaging (SARP) provides the analyses and evaluations necessary to demonstrate that the TRU PDP sample packaging meets the onsite transportation safety requirements of WHC-CM-2-14, Hazardous Material Packaging and Shipping, for an onsite Transportation Hazard Indicator (THI) 2 packaging. This SARP, however, does not include evaluation of any operations within the PFP or WRAP facilities, including handling, maintenance, storage, or operating requirements, except as they apply directly to transportation between the gate of PFP and the gate of the WRAP facility. All other activities are subject to the requirements of the facility safety analysis reports (FSAR) of the PFP or WRAP facility and requirements of the PDP

RELEASE OF DRIED RADIOACTIVE WASTE MATERIALS TECHNICAL BASIS DOCUMENT

International Nuclear Information System (INIS)

KOZLOWSKI, S.D.

2007-01-01

This technical basis document was developed to support RPP-23429, Preliminary Documented Safety Analysis for the Demonstration Bulk Vitrification System (PDSA) and RPP-23479, Preliminary Documented Safety Analysis for the Contact-Handled Transuranic Mixed (CH-TRUM) Waste Facility. The main document describes the risk binning process and the technical basis for assigning risk bins to the representative accidents involving the release of dried radioactive waste materials from the Demonstration Bulk Vitrification System (DBVS) and to the associated represented hazardous conditions. Appendices D through F provide the technical basis for assigning risk bins to the representative dried waste release accident and associated represented hazardous conditions for the Contact-Handled Transuranic Mixed (CH-TRUM) Waste Packaging Unit (WPU). The risk binning process uses an evaluation of the frequency and consequence of a given representative accident or represented hazardous condition to determine the need for safety structures, systems, and components (SSC) and technical safety requirement (TSR)-level controls. A representative accident or a represented hazardous condition is assigned to a risk bin based on the potential radiological and toxicological consequences to the public and the collocated worker. Note that the risk binning process is not applied to facility workers because credible hazardous conditions with the potential for significant facility worker consequences are considered for safety-significant SSCs and/or TSR-level controls regardless of their estimated frequency. The controls for protection of the facility workers are described in RPP-23429 and RPP-23479. Determination of the need for safety-class SSCs was performed in accordance with DOE-STD-3009-94, Preparation Guide for US. Department of Energy Nonreactor Nuclear Facility Documented Safety Analyses, as described below

Allowable residual contamination levels: transuranic advanced disposal systems for defense waste

International Nuclear Information System (INIS)

Kennedy, W.E. Jr.; Napier, B.A.

1982-01-01

An evaluation of advanced disposal systems for defense transuranic (TRU) wastes is being conducted using the Allowable Residual Contamination Level (ARCL) method. The ARCL method is based on compliance with a radiation dose rate limit through a site-specific analysis of the potential for radiation exposure to individuals. For defense TRU wastes at the Hanford Site near Richland, Washington, various advanced disposal techniques are being studied to determine their potential for application. This paper presents a discussion of the results of the first stage of the TRU advanced disposal systems project

Quantification of transuranic elements by time interval correlation spectroscopy of the detected neutrons

Science.gov (United States)

Baeten; Bruggeman; Paepen; Carchon

2000-03-01

The non-destructive quantification of transuranic elements in nuclear waste management or in safeguards verifications is commonly performed by passive neutron assay techniques. To minimise the number of unknown sample-dependent parameters, Neutron Multiplicity Counting (NMC) is applied. We developed a new NMC-technique, called Time Interval Correlation Spectroscopy (TICS), which is based on the measurement of Rossi-alpha time interval distributions. Compared to other NMC-techniques, TICS offers several advantages.

Flexible Electrostatic Technologies for Capture and Handling, Phase 1

Science.gov (United States)

Bryan, Thomas

2015-01-01

Fundamental to many of NASA's in-space transportation missions is the capture and handling of various objects and vehicles in various orbits for servicing, debris disposal, sample retrieval, and assembly without the benefit of sufficient grapple fixtures and docking ports. To perform similar material handling tasks on Earth, pincher grippers, suction grippers, or magnetic chucks are used, but are unable to reliably grip aluminum and composite spacecraft, insulation, radiators, solar arrays, or extra-terrestrial objects in the vacuum of outer space without dedicated handles in the right places. The electronic Flexible Electrostatic Technologies for space Capture and Handling (FETCH) will enable reliable and compliant gripping (soft dock) of practically any object in various orbits or surfaces without dedicated mechanical features, very low impact capture, and built-in proximity sensing without any conventional actuators. Originally developed to handle semiconductor and glass wafers during vacuum chamber processing without contamination, the normal rigid wafer handling chucks are replaced with thin metal foil segments laminated in flexible insulation driven by commercial off-the-shelf solid state, high-voltage power supplies. Preliminary testing in NASA Marshall Space Flight Center's (MSFC's) Flat Floor Robotics Lab demonstrated compliant alignment and gripping with a full-sized, 150-lb microsat mockup and translation before a clean release with a flip of a switch. The flexible electrostatic gripper pads can be adapted to various space applications with different sizes, shapes, and foil electrode layouts even with openings through the gripper pads for addition of guidance sensors or injection of permanent adhesives. With gripping forces estimated between 0.5 and 2.5 lb/in2 or 70-300 lb/ft2 of surface contact, the FETCH can turn on and off rapidly and repeatedly to enable sample handling, soft docking, in-space assembly, precision relocation, and surface translation

Using Downhole Probes to Locate and Characterize Buried Transuranic and Mixed Low Level Waste

Energy Technology Data Exchange (ETDEWEB)

Steinman, Donald K; Bramblett, Richard L; Hertzog, Russel C

2012-06-25

Borehole logging probes were developed and tested to locate and quantify transuranic elements in subsurface disposal areas and in contaminated sites at USDOE Weapons Complex sites. A new method of measuring very high levels of chlroine in the subsurface was developed using pulsed neutron technology from oilfield applications. The probes were demonstrated at the Hanford site in wells containing plutonium and other contaminants.

Density, movement, and transuranic tissue inventory of small mammals at a liquid-radioactive waste disposal area

International Nuclear Information System (INIS)

Halford, D.K.

1987-01-01

Linear movement, density, and transuranic radionuclide inventory were estimated for small mammals residing at a liquid radioactive waste disposal area in southeastern Idaho. Deer mice (Peromyscus maniculatus), kangaroo rats (Dipodomys ordii), western harvest mice (Reithrodontomys megalotis), and Great Basin pocket mice (Perognathus parvus) were the predominant species. The total small mammal population within the 3.0-ha waste area was estimated to be 93. The distance between consecutive captures for all species combined averaged 41 m and ranged from 7 to 201 m. About 30% of the rodents captured inside the waste area were also captured outside its boundaries. The total population inventory of 238 Pu, /sup 239,240/Pu, 241 Am, 242 Cm, and 244 Cm was 44 pCi, 30 pCi, 19 pCi, 21 pCi, and <1 pCi, respectively. One-third, or about 35 pCi of transuranics, could be removed from the waste area by small mammals during the summer of 1981. 16 references, 3 figures, 3 tables

Los Alamos Transuranic Waste Size Reduction Facility

International Nuclear Information System (INIS)

Harper, J.; Warren, J.

1987-01-01

The Los Alamos Transuranic (TRU) Waste Size Reduction Facility (SRF) is a production oriented prototype completed in 1981 and later modified during 1986 to enhance production. The facility is operated to remotely cut (with a plasma arc torch) and repackage TRU contaminated metallic wastes (e.g., glove boxes, ducting and pipes) for eventual disposal at the Waste Isolation Pilot Plant (WIPP) near Carlsbad, New Mexico. The resulting flat sections are packaged into a tested Department of Transportation Type 7A metal container. To date, the facility has successfully processed stainless steel glove boxes (with and without lead shielding construction) and retention tanks. It was found that used glove boxes generate more cutting fumes than do unused glove boxes or metal plates - possibly due to deeply embedded chemical residues from years of service. Water used as a secondary fluid with the plasma arc cutting system significantly reduces visible fume generation during the cutting of used glove boxes and lead-lined glove boxes

Quality assurance guidance for TRUPACT-II [Transuranic Package Transporter-II] payload control

International Nuclear Information System (INIS)

1989-10-01

The Transuranic Package Transporter-II (TRUPACT-II) Safety Analysis Report for Packaging (SARP) approved by the Nuclear Regulatory Commission (NRC), discusses authorized methods for payload control in Appendix 1.3.7 and the Quality Assurance (QA) requirements in Section 9.3. Subsection 9.3.2.1 covers maintenance and use of the TRUPACT-II and the specific QA requirements are given in DOE/WIPP 89-012. Subsection 9.3.2.2 covers payload compliance, for which this document was written. 6 refs

Transuranic waste program at EG and G Idaho, Inc. Annual technical report

International Nuclear Information System (INIS)

Smith, T.H.; Tolman, C.R.

1980-12-01

This document summarizes the objectives and technical achievements of the transuranic (TRU) waste research and development program conducted at EG and G Idaho, Inc., during fiscal year 1980. The TRU waste activities covered in this report include: INEL TRU Waste EIS (Environmental Impact Statement), including preparation of the EIS, Support Studies, and the Public Participation Program; INEL TRU Waste Projects, including System Analysis, Stored Waste projects, and Buried Waste projects; and Waste Management Materials Studies, including Process Control and Durability studies

The chemical behavior of the transuranic elements and the barrier function in natural aquifer systems

International Nuclear Information System (INIS)

Jewett, J.R.

1997-01-01

In a geological repository for long-lived radioactive wastes, such as actinides and certain fission products, most of the stored radionuclides remain immobile in the particular geological formation. If any of these could possibly become mobile, only trace concentrations of a few radionuclides would result. Nevertheless, with an inventory in the repository of many tonnes of transuranic elements, the amounts that could disperse cannot be neglected. A critical assessment of the chemical behavior of these nuclides, especially their migration properties in the aquifer system around the repository site, is mandatory for analysis of the long-term safety. The chemistry requited for this includes many geochemical multicomponent reactions that are so far only partially understood and hich therefore can be quantified only incompletely. A few of these reactions have been discussed in this paper based on present knowledge. If a comprehensive discussion of the subject is impossible because of this ack of information then an attempt to emphasize the importance of the predominant geochemical reactions of the transuranic elements in various aquifer systems should be made

Analysis and model testing of a Super Tiger Type B waste transport system in accident environments

International Nuclear Information System (INIS)

May, R.A.; Yoshimura, H.R.; Romesberg, L.E.; Joseph, B.J.

1980-01-01

Sandia National Laboratories is investigating the response of a Type B packaging containing drums of contact-handled transuranic waste (CH-TRU) as a part of a program to evaluate the adequacy of experimental and analytical methods for assessing the safety of waste transport systems in accident environments. A US NRC certified Type B package known as the Super Tiger was selected for the study. This overpack consists of inner and outer steel shells separated by rigid polyurethane foam and can be used for either highway or rail transportation. Tests using scale models of the vehicular system are being conducted in conjunction with computer analyses

Preliminary radiological analysis of the transportation of contact-handled transuranic waste within the state of New Mexico. Revision 1

International Nuclear Information System (INIS)

Tappen, J.; Fredrickson, C.; Daer, G.

1985-06-01

This analysis assesses the potential radiological impacts on the citizens of New Mexico from the transport of CH-TRU waste to WIPP by rail or by truck. Assuming exclusive use of the truck transport mode, the combined annual exposure to the public from accident-free shipment of waste is estimated to be 3.3 person-rem/year. It is estimated that a theoretical member of the public receiving maximum exposure to the combined truck shipments of CH-TRU waste to WIPP would receive an annual whole body dose equivalent of 0.000016 rem. Such an exposure is insignificant in comparison to the average annual whole body dose equivalent to an individual living in the Colorado Plateau area of between 0.075 and 0.140 rem from natural occurring radiation. The combined annual radiological risk to the public living along the new Mexico truck routes to WIPP from potential accidents is projected as 0.031 person-rem/year. Assuming exclusive use of the rail transport mode, the combined annual exposure to the public from accident-free shipment of waste is estimated to be 1.2 person-rem/year. A theoretical member of the public receiving combined maximum exposure to rail shipments of CH-TRU waste to WIPP would receive an annual whole body dose equivalent of 0.000012 rem. The combined annual radiological risk to the public living along the New Mexico rail routes to WIPP from potential accidents is projected as 0.0022 person-rem/year. An estimate of the radiological impacts in a year of maximum waste receipt can be made by multiplying the above results for rail or truck by 2. This estimate is based upon the WIPP design waste throughput rate of 500,000 ft 3 per year. An estimate of the radiological impacts of CH-TRU waste transport to WIPP over the facility life can be made by multiplying the above results by 25

Research and development program for transuranic-contaminated waste within the U.S. Energy Research and Development Administration

International Nuclear Information System (INIS)

Wolfe, R.A.

1976-01-01

This overview examines the research and development program that has been established within the U.S. Energy Research and Development Administration (ERDA) to develop the technology to treat transuranic-contaminated waste. Also considered is the waste expected within the total nuclear fuel cycle

Nevada Applied Ecology Group procedures handbook for environmental transuranics

International Nuclear Information System (INIS)

White, M.G.; Dunaway, P.B.

1976-10-01

The activities of the Nevada Applied Ecology Group (NAEG) integrated research studies of environmental plutonium and other transuranics at the Nevada Test Site have required many standardized field and laboratory procedures. These include sampling techniques, collection and preparation, radiochemical and wet chemistry analysis, data bank storage and reporting, and statistical considerations for environmental samples of soil, vegetation, resuspended particles, animals, and other biological material. This document, printed in two volumes, includes most of the Nevada Applied Ecology Group standard procedures, with explanations as to the specific applications involved in the environmental studies. Where there is more than one document concerning a procedure, it has been included to indicate special studies or applications more complex than the routine standard sampling procedures utilized

Nevada Applied Ecology Group procedures handbook for environmental transuranics

International Nuclear Information System (INIS)

White, M.G.; Dunaway, P.B.

1976-10-01

The activities of the Nevada Applied Ecology Group (NAEG) integrated research studies of environmental plutonium and other transuranics at the Nevada Test Site have required many standardized field and laboratory procedures. These include sampling techniques, collection and preparation, radiochemical and wet chemistry analysis, data bank storage and reporting, and statistical considerations for environmental samples of soil, vegetation, resuspended particles, animals, and others. This document, printed in two volumes, includes most of the Nevada Applied Ecology Group standard procedures, with explanations as to the specific applications involved in the environmental studies. Where there is more than one document concerning a procedure, it has been included to indicate special studies or applications perhaps more complex than the routine standard sampling procedures utilized

Effect of Burnable Absorbers on Inert Matrix Fuel Performance and Transuranic Burnup in a Low Power Density Light-Water Reactor

Directory of Open Access Journals (Sweden)

Geoff Recktenwald

2013-04-01

Full Text Available Zirconium dioxide has received particular attention as a fuel matrix because of its ability to form a solid solution with transuranic elements, natural radiation stability and desirable mechanical properties. However, zirconium dioxide has a lower coefficient of thermal conductivity than uranium dioxide and this presents an obstacle to the deployment of these fuels in commercial reactors. Here we show that axial doping of a zirconium dioxide based fuel with erbium reduces power peaking and fuel temperature. Full core simulations of a modified AP1000 core were done using MCNPX 2.7.0. The inert matrix fuel contained 15 w/o transuranics at its beginning of life and constituted 28% of the assemblies in the core. Axial doping reduced power peaking at startup by more than ~23% in the axial direction and reduced the peak to average power within the core from 1.80 to 1.44. The core was able to remain critical between refueling while running at a simulated 2000 MWth on an 18 month refueling cycle. The results show that the reactor would maintain negative core average reactivity and void coefficients during operation. This type of fuel cycle would reduce the overall production of transuranics in a pressurized water reactor by 86%.

Hazardous gas production by alpha particles in solid organic transuranic waste matrices. 1998 annual progress report

International Nuclear Information System (INIS)

LaVerne, J.A.

1998-01-01

'This project uses fundamental radiation chemical techniques to elucidate the basic processes occurring in the heavy-ion radiolysis of solid hydrocarbon matrices such as polymers and organic resins that are associated with many of the transuranic waste deposits or the transportation of these radionuclides. The environmental management of mixed waste containing transuranic radionuclides is difficult because these nuclides are alpha particle emitters and the energy deposited by the alpha particles causes chemical transformations in the matrices accompanying the waste. Most radiolysis programs focus on conventional radiation such as gamma rays, but the chemical changes induced by alpha particles and other heavy ions are typically very different and product yields can vary by more than an order of magnitude. The objective of this research is to measure the production of gases, especially molecular hydrogen, produced in the proton, helium ion, and carbon ion radiolysis of selected solid organic matrices in order to obtain fundamental mechanistic information on the radiolytic decomposition of these materials. This knowledge can also be used to directly give reasonable estimates of explosive or flammability hazards in the storage or transport of transuranic wastes in order to enhance the safety of DOE sites. This report summarizes the work after eight months of a three-year project on determining the production of hazardous gases in transuranic waste. The first stage of the project was to design and build an assembly to irradiate solid organic matrices using accelerated ion beams. It is necessary to measure absolute radiolytic yields, and simulate some of the conditions found in the field. A window assembly was constructed allowing the beam to pass consecutively through a collimator, a vacuum exit window and into the solid sample. The beam is stopped in the sample and the entire end of the assembly is a Faraday cup. Integration of the collected current, in conjunction

Evidence for the remobilisation of transuranic elements in the terrestrial environment.

Science.gov (United States)

Hursthouse, A S; Livens, F R

1993-09-01

The transuranium elements, Np, Pu and Am discharged from the BNFL fuel reprocessing plant at Sellafield have accumulated in the local environment. The processes responsible for their dispersal rely both on physical transportation and their chemical reactivity. The transuranics have a complex chemistry, with multiple oxidation states and a strongly polarising character. In the environment, the particle active III/IV and more mobile VNI oxidation state groups are important and govern their geochemical behaviour and subsequent dispersal.Studies of the behaviour of the transuranics, particularly Pu, in the Irish Sea, have shown that the majority of the radionuclides in the liquid effluent discharged from Sellafield, quickly becomes associated with the marine sediments. Their dispersal and distribution in the environment is then governed primarily by the movement of particulate material and for some sites it has been suggested that sediment profiles preserve the historical record of discharges from the plant.In tidally inundated soils, radionuclide levels are greatly enhanced. These soils are water-logged for long periods of the year, are strongly anoxic and accretion rate are very low. The distribution of Np, Pu and Am in the soil suggests that simple sedimentary accumulation mechanism cannot provide an adequate explanation for the profiles observed. From preliminary studies of soil pore water composition and detailed analysis of the variation of isotopic ratios in the soil cores, it is apparent that a small but significant component of the radionuclide inventory is mobile. In addition, it is clear that the mechanisms responsible for this mobility allows differentiation between the transuranium nuclides.

Leaching of transuranics observed in lysimeter experiments

International Nuclear Information System (INIS)

Eriksson, A.; Fredriksson, L.

1994-01-01

Transuranic elements in fallout are generally bound in oxide particles, size from submicron to several microns. During the fallout they can be intercepted on plant covers or reach the soil surface. The particles can be re-suspended to the air and reach other residence sites, be linked into the food chain or be redistributed in other ways (Cf Essington et al. 1976) before eventually being incorporated into the soil. The fate of such particles in the soil depends on the size and on the nature of the particulate matter and on environmental factors, the climate and the properties of the soil. In a dry climate the particles tend to be kept intact long time, (Schulz et al. 1976) and they are more easily redistributed than in a humid climate with plant covered moist and living soils. In the former the particles move more easily in the soil profile than in the latter, the particle matter is very slowly dissolved and the average availability of the deposited nuclides for plant uptake can be assumed to be comparatively low. The downward movements of the particles or nuclide compounds bound to small soil particles are enhanced by the swelling and shrinking of soil caused by absorption and depletion of water during the season. Cracks and fissures are created and closed several times a year in soils rich in colloidal material. Sandy soils with coarse material have less cracks, but in dry conditions the empty pore space may allow transport of fine particles. The coarser material also has less specific area and sorption capacity. The nuclide compounds leached with the drainage water in coarse soils should be less retarded than in clays (Cf. Rai and Serne, 1977; Nishita and Haug, 1979 and Rai et al., 1980). The lysimeter installation used for the study reported below was primarily designed to study the plant uptake of transuranics from a number of Swedish soils. However, as such an installation in many ways well simulate field conditions and at the same time is a closed system

Fuel handling machine and auxiliary systems for a fuel handling cell

International Nuclear Information System (INIS)

Suikki, M.

2013-10-01

This working report is an update for as well as a supplement to an earlier fuel handling machine design (Kukkola and Roennqvist 2006). A focus in the earlier design proposal was primarily on the selection of a mechanical structure and operating principle for the fuel handling machine. This report introduces not only a fuel handling machine design but also auxiliary fuel handling cell equipment and its operation. An objective of the design work was to verify the operating principles of and space allocations for fuel handling cell equipment. The fuel handling machine is a remote controlled apparatus capable of handling intensely radiating fuel assemblies in the fuel handling cell of an encapsulation plant. The fuel handling cell is air tight space radiation-shielded with massive concrete walls. The fuel handling machine is based on a bridge crane capable of traveling in the handling cell along wall tracks. The bridge crane has its carriage provided with a carousel type turntable having mounted thereon both fixed and telescopic masts. The fixed mast has a gripper movable on linear guides for the transfer of fuel assemblies. The telescopic mast has a manipulator arm capable of maneuvering equipment present in the fuel handling cell, as well as conducting necessary maintenance and cleaning operations or rectifying possible fault conditions. The auxiliary fuel handling cell systems consist of several subsystems. The subsystems include a service manipulator, a tool carrier for manipulators, a material hatch, assisting winches, a vacuum cleaner, as well as a hose reel. With the exception of the vacuum cleaner, the devices included in the fuel handling cell's auxiliary system are only used when the actual encapsulation process is not ongoing. The malfunctions of mechanisms or actuators responsible for the motion actions of a fuel handling machine preclude in a worst case scenario the bringing of the fuel handling cell and related systems to a condition appropriate for

Fuel handling machine and auxiliary systems for a fuel handling cell

Energy Technology Data Exchange (ETDEWEB)

Suikki, M. [Optimik Oy, Turku (Finland)

2013-10-15

This working report is an update for as well as a supplement to an earlier fuel handling machine design (Kukkola and Roennqvist 2006). A focus in the earlier design proposal was primarily on the selection of a mechanical structure and operating principle for the fuel handling machine. This report introduces not only a fuel handling machine design but also auxiliary fuel handling cell equipment and its operation. An objective of the design work was to verify the operating principles of and space allocations for fuel handling cell equipment. The fuel handling machine is a remote controlled apparatus capable of handling intensely radiating fuel assemblies in the fuel handling cell of an encapsulation plant. The fuel handling cell is air tight space radiation-shielded with massive concrete walls. The fuel handling machine is based on a bridge crane capable of traveling in the handling cell along wall tracks. The bridge crane has its carriage provided with a carousel type turntable having mounted thereon both fixed and telescopic masts. The fixed mast has a gripper movable on linear guides for the transfer of fuel assemblies. The telescopic mast has a manipulator arm capable of maneuvering equipment present in the fuel handling cell, as well as conducting necessary maintenance and cleaning operations or rectifying possible fault conditions. The auxiliary fuel handling cell systems consist of several subsystems. The subsystems include a service manipulator, a tool carrier for manipulators, a material hatch, assisting winches, a vacuum cleaner, as well as a hose reel. With the exception of the vacuum cleaner, the devices included in the fuel handling cell's auxiliary system are only used when the actual encapsulation process is not ongoing. The malfunctions of mechanisms or actuators responsible for the motion actions of a fuel handling machine preclude in a worst case scenario the bringing of the fuel handling cell and related systems to a condition appropriate for

Waste Management facilities cost information: System Cost Model Software Quality Assurance Plan. Revision 2

International Nuclear Information System (INIS)

Peterson, B.L.; Lundeen, A.S.

1996-02-01

In May of 1994, Lockheed Idaho Technologies Company (LITCO) in Idaho Falls, Idaho and subcontractors developed the System Cost Model (SCM) application. The SCM estimates life-cycle costs of the entire US Department of Energy (DOE) complex for designing; constructing; operating; and decommissioning treatment, storage, and disposal (TSD) facilities for mixed low-level, low-level, transuranic, and mixed transuranic waste. The SCM uses parametric cost functions to estimate life-cycle costs for various treatment, storage, and disposal modules which reflect planned and existing facilities at DOE installations. In addition, SCM can model new facilities based on capacity needs over the program life cycle. The SCM also provides transportation costs for truck and rail, which include transport of contact-handled, remote-handled, and alpha (transuranic) wastes. The user can provide input data (default data is included in the SCM) including the volume and nature of waste to be managed, the time period over which the waste is to be managed, and the configuration of the waste management complex (i.e., where each installation's generated waste will be treated, stored, and disposed). Then the SCM uses parametric cost equations to estimate the costs of pre-operations (designing), construction costs, operation management, and decommissioning these waste management facilities. For the product to be effective and useful the SCM users must have a high level of confidence in the data generated by the software model. The SCM Software Quality Assurance Plan is part of the overall SCM project management effort to ensure that the SCM is maintained as a quality product and can be relied on to produce viable planning data. This document defines tasks and deliverables to ensure continued product integrity, provide increased confidence in the accuracy of the data generated, and meet the LITCO's quality standards during the software maintenance phase. 8 refs., 1 tab

Waste Management facilities cost information: System Cost Model Software Quality Assurance Plan. Revision 2

Energy Technology Data Exchange (ETDEWEB)

Peterson, B.L.; Lundeen, A.S.

1996-02-01

In May of 1994, Lockheed Idaho Technologies Company (LITCO) in Idaho Falls, Idaho and subcontractors developed the System Cost Model (SCM) application. The SCM estimates life-cycle costs of the entire US Department of Energy (DOE) complex for designing; constructing; operating; and decommissioning treatment, storage, and disposal (TSD) facilities for mixed low-level, low-level, transuranic, and mixed transuranic waste. The SCM uses parametric cost functions to estimate life-cycle costs for various treatment, storage, and disposal modules which reflect planned and existing facilities at DOE installations. In addition, SCM can model new facilities based on capacity needs over the program life cycle. The SCM also provides transportation costs for truck and rail, which include transport of contact-handled, remote-handled, and alpha (transuranic) wastes. The user can provide input data (default data is included in the SCM) including the volume and nature of waste to be managed, the time period over which the waste is to be managed, and the configuration of the waste management complex (i.e., where each installation`s generated waste will be treated, stored, and disposed). Then the SCM uses parametric cost equations to estimate the costs of pre-operations (designing), construction costs, operation management, and decommissioning these waste management facilities. For the product to be effective and useful the SCM users must have a high level of confidence in the data generated by the software model. The SCM Software Quality Assurance Plan is part of the overall SCM project management effort to ensure that the SCM is maintained as a quality product and can be relied on to produce viable planning data. This document defines tasks and deliverables to ensure continued product integrity, provide increased confidence in the accuracy of the data generated, and meet the LITCO`s quality standards during the software maintenance phase. 8 refs., 1 tab.

Management of waste cladding hulls. Part II. An assessment of zirconium pyrophoricity and recommendations for handling waste hulls

International Nuclear Information System (INIS)

Kullen, B.J.; Levitz, N.M.; Steindler, M.J.

1977-11-01

This report reviews experience and research related to the pyrophoricity of zirconium and zirconium alloys. The results of recent investigations of the behavior of Zircaloy and some observations of industrial handling and treatment of Zircaloy tubing and scrap are also discussed. A model for the management of waste Zircaloy cladding hulls from light water reactor fuel reprocessing is offered, based on an evaluation of the reviewed information. It is concluded that waste Zircaloy cladding hulls do not constitute a pyrophoric hazard if, following the model flow sheet, finely divided metal is oxidized during the management procedure. Steps alternative to the model are described which yield zirconium in deactivated form and also accomplish varying degrees of transuranic decontamination. Information collected into appendixes is (1) a collation of zirconium pyrophoricity data from the literature, (2) calculated radioactivity contents in Zircaloy cladding hulls from spent LWR fuels, and (3) results of a laboratory study on volatilization of zirconium from Zircaloy using HCl or Cl 2

Handling sticky resin by stingless bees (Hymenoptera, Apidae

Directory of Open Access Journals (Sweden)

Markus Gastauer

2011-06-01

Full Text Available For their nest defense, stingless bees (Meliponini collect plant resins which they stick on intruders like ants or cleptobiotic robber bees causing their immobilization. The aim of this article is to identify all parts of stingless bee workers contacting these sticky resins. Of special interest are those body parts with anti-adhesive properties to resin, where it can be removed without residues. For that, extensive behavioral observations during foraging flight, handling and application of the resin have been carried out. When handling the resin, all tarsi touch the resin while walking above it. For transportation from plants to the nest during foraging flight, the resin is packed to the corbicula via tarsi and basitarsi of front and middle legs. Once stuck to the resin or after the corbicula had been unloaded, the bee's legs have to be cleaned thoroughly. Only the tips of the mandibles, that form, cut and apply the sticky resin, seem to have at least temporarily resin-rejecting properties.

Geomicrobiological redox cycling of the transuranic element neptunium.

Science.gov (United States)

Law, Gareth T W; Geissler, Andrea; Lloyd, Jonathan R; Livens, Francis R; Boothman, Christopher; Begg, James D C; Denecke, Melissa A; Rothe, Jörg; Dardenne, Kathy; Burke, Ian T; Charnock, John M; Morris, Katherine

2010-12-01

Microbial processes can affect the environmental behavior of redox sensitive radionuclides, and understanding these reactions is essential for the safe management of radioactive wastes. Neptunium, an alpha-emitting transuranic element, is of particular importance because of its long half-life, high radiotoxicity, and relatively high solubility as Np(V)O(2)(+) under oxic conditions. Here, we describe experiments to explore the biogeochemistry of Np where Np(V) was added to oxic sediment microcosms with indigenous microorganisms and anaerobically incubated. Enhanced Np removal to sediments occurred during microbially mediated metal reduction, and X-ray absorption spectroscopy showed this was due to reduction to poorly soluble Np(IV) on solids. In subsequent reoxidation experiments, sediment-associated Np(IV) was somewhat resistant to oxidative remobilization. These results demonstrate the influence of microbial processes on Np solubility and highlight the critical importance of radionuclide biogeochemistry in nuclear legacy management.

Immobilization of transuranic sludge in glass-ceramic materials

International Nuclear Information System (INIS)

Welch, J.M.; Schuman, R.P.; Flinn, J.E.

1982-03-01

Studies were performed to determine the effectiveness of glass-ceramic waste forms, particularly iron-enriched basalt, for immobilizing transuranic waste sludges from the Rocky Flats plant operations. Two sludges were used in the study - one was nonradioactive and the other contained approx. 2200 dps/mg of 241 Am. The glass-ceramic waste forms were produced from laboratory-scale melting operations with subsequent controlled cooling. The waste forms were examined to assess the microstructures which resulted from systematically varied compositions and controlled cooling sequences. Leach tests in deionized water were performed on small monolithic specimens of the various glass-ceramic materials. The test results showed a rather strong temperature dependence for leach rates. Also, for some of these materials, marked differences in the 241 Am leaching behavior were seen in measurements obtained on acidified versus neutral aliquots of the spent leachates. 8 figures, 12 tables

Physical Properties of Hanford Transuranic Waste Sludge

International Nuclear Information System (INIS)

Poloski, A. P.

2004-01-01

This project has two primary objectives. The first is to understand the physical properties and behavior of the Hanford transuranic (TRU) tank sludges under conditions that might exist during retrieval, treatment, packaging, and transportation for disposal at WIPP. The second primary objective is to develop a fundamental understanding of these sludge suspensions by correlating the macroscopic properties with particle interactions occurring at the colloidal scale in the various liquid media. The results of this research effort will enhance the existing understanding of agglomeration phenomena and the properties of complex colloidal suspensions. In addition, the knowledge gained and capabilities developed during this effort will aid in the development and optimization of techniques to process the wastes at various DOE sites. These objectives will be accomplished by: (1) characterizing the TRU sludges contained in the Hanford tanks that are intended for shipment to WIPP; (2) determining the physical behavior of the Hanford TRU tank sludges under conditions that might exist during treatment and packaging; (3) and modeling the retrieval, treatment, and packaging operations that will be performed at Hanford to dispose of TRU tank sludges

Safe handling of cytotoxic compounds in a biopharmaceutical environment.

Science.gov (United States)

Hensgen, Miriam I; Stump, Bernhard

2013-01-01

Handling cytotoxic drugs such as antibody-drug conjugates (ADCs) in a biopharmaceutical environment represents a challenge based on the potency of the compounds. These derivatives are dangerous to humans if they accidentally get in contact with the skin, are inhaled, or are ingested, either as pure compounds in their solid state or as a solution dissolved in a co-solvent. Any contamination of people involved in the manufacturing process has to be avoided. On the other hand, biopharmaceuticals need to be protected simultaneously against any contamination from the manufacturing personnel. Therefore, a tailor-made work environment is mandatory in order to manufacture ADCs. This asks for appropriate technical equipment to keep potential hazardous substances contained. In addition, clearly defined working procedures based on risk assessments as well as proper training for all personnel involved in the manufacturing process are needed to safely handle these highly potent pharmaceuticals.

Environmental Radiation Protection Standards for Management and Disposal of Spent Nuclear Fuel and Transuranic Radioactive Wastes (40 CFR Part 191)

Science.gov (United States)

This regulation sets environmental standards for public protection from the management and disposal of spent nuclear fuel, high-level wastes and wastes that contain elements with atomic numbers higher than uranium (transuranic wastes).

A Nurse Communication Manager reduces the number of non‑relevant contacts

DEFF Research Database (Denmark)

Wright, Nana Keir; Seested Nielsen, Nina; Lauersen, Jannie

2015-01-01

Objective The aim of this study was to reduce interruptions in nursing practice by exploring the effects on the number of nonrelevant contacts received by the nursing staff after implementation of a Nurse Communication Manager. Design The study was designed as a pre/post interventional study. All...... in the surgical department. Interventions During the daytime a Nurse Communication Manager handled all incoming contacts irrespective of whether they were in person or by telephone. When the Nurse Communication Manager was not available and during the evening, night and weekends, telephone contacts were managed...... by an electronic Call Centre guiding the call to the care teams. Main outcome measure(s) The main outcome measures were the number of non-relevant contacts aimed at the nursing staff. Results Results showed a significant reduction in non-relevant contacts to the nursing staff from a mean of 80 contacts per day (SD...

Contact allergy to epoxy resin

DEFF Research Database (Denmark)

Bangsgaard, Nannie; Thyssen, Jacob Pontoppidan; Menné, Torkil

2012-01-01

Background. Epoxy resin monomers are strong skin sensitizers that are widely used in industrial sectors. In Denmark, the law stipulates that workers must undergo a course on safe handling of epoxy resins prior to occupational exposure, but the effectiveness of this initiative is largely unknown...... in an educational programme. Conclusion. The 1% prevalence of epoxy resin contact allergy is equivalent to reports from other countries. The high occurrence of epoxy resin exposure at work, and the limited use of protective measures, indicate that reinforcement of the law is required....

A Title 40 Code of Federal Regulations Part 191 Evaluation of Buried Transuranic Waste at the Nevada Test Site - 8210

International Nuclear Information System (INIS)

G J Shott; V Yucel; L Desotell

2008-01-01

In 1986, 21 m 3 of transuranic (TRU) waste was inadvertently buried in a shallow land burial trench at the Area 5 Radioactive Waste Management Site on the Nevada Test Site (NTS). The U.S. Department of Energy, National Nuclear Security Administration Nevada Site Office is considered five options for management of the buried TRU waste. One option is to leave the waste in-place if the disposal can meet the requirements of Title 40 Code of Federal Regulations (CFR) Part 191, 'Environmental Radiation Protection Standard for Management and Disposal of Spent Nuclear Fuel, High-Level, and Transuranic Radioactive Wastes'. This paper describes analyses that assess the likelihood that TRU waste in shallow land burial can meet the 40 CFR 191 standards for a geologic repository. The simulated probability of the cumulative release exceeding 1 and 10 times the 40 CFR 191.13 containment requirements is estimated to be 0.009 and less than 0.0001, respectively. The cumulative release is most sensitive to the number of groundwater withdrawal wells drilled through the disposal trench. The mean total effective dose equivalent for a member of the public is estimated to reach a maximum of 0.014 milliSievert (mSv) at 10,000 years, or approximately 10 percent of the 0.15 mSv 40 CFR 191.15 individual protection requirement. The dose is predominantly from inhalation of short-lived Rn-222 progeny in air produced by low-level waste disposed in the same trench. The transuranic radionuclide released in greatest amounts, Pu-239, contributes only 0.4 percent of the dose. The member of public dose is most sensitive to the U-234 inventory and the radon emanation coefficient. Reasonable assurance of compliance with the Subpart C groundwater protection standard is provided by site characterization data and hydrologic processes modeling which support a conclusion of no groundwater pathway within 10,000 years. Limited quantities of transuranic waste in a shallow land burial trench at the NTS can meet

Radioactive waste management: a series of bibliographies. Transuranic wastes. Supplement 1

International Nuclear Information System (INIS)

McLaren, L.H.

1985-04-01

This bibliography contains information on transuranic waste included in the Department of Energy's Energy Data Base from August 1982 through December 1983. The abstracts are grouped by subject category as shown in the table of contents. Entries in the subject index also facilitate access by subject, e.g., Alpha-Bearing Wastes/Packaging. Within each category the arrangement is by report number for reports, followed by nonreports in reverse chronological order. These citations are to research reports, journal articles, books, patents, theses, and conference papers from worldwide sources. Five indexes, each preceded by a brief description, are provided: Corporate Author, Personal Author, Subject, Contract Number, and Report Number

Assessment of LANL transuranic mixed waste management documentation

International Nuclear Information System (INIS)

Davis, K.D.; Hoevemeyer, S.S.; McCance, C.H.; Jennrich, E.A.; Lund, D.M.

1991-04-01

The objective of this report is to present findings from the evaluation of the Los Alamos National Laboratory (LANL) TRU Mixed Waste Acceptance Criteria to determine its compliance with applicable DOE requirements. The driving requirements for s TRU Mixed Waste Acceptance Criteria are essentially those contained in the ''TRU Waste Acceptance Criteria for the Waste Isolation Pilot Plant'' or WIPP WAC (DOE Report WIPP-DOE-069), 40 CFR 261-270, and DOE Order 5820.2A (Radioactive Waste Management), specifically Chapter II which is entitled ''Management of Transuranic Waste''. The primary purpose of the LANL WAC is the establishment of those criteria that must be met by generators of TRU mixed waste before such waste can be accepted by the Waste Management Group. An annotated outline of a genetic TRU mixed waste acceptance criteria document was prepared from those requirements contained in the WIPP WAC, 40 CFR 261-270, and 5820.2A, and is based solely upon those requirements

Ceramics for Molten Materials Containment, Transfer and Handling on the Lunar Surface

Science.gov (United States)

Standish, Evan; Stefanescu, Doru M.; Curreri, Peter A.

2009-01-01

As part of a project on Molten Materials Transfer and Handling on the Lunar Surface, molten materials containment samples of various ceramics were tested to determine their performance in contact with a melt of lunar regolith simulant. The test temperature was 1600 C with contact times ranging from 0 to 12 hours. Regolith simulant was pressed into cylinders with the approximate dimensions of 1.25 dia x 1.25cm height and then melted on ceramic substrates. The regolith-ceramic interface was examined after processing to determine the melt/ceramic interaction. It was found that the molten regolith wetted all oxide ceramics tested extremely well which resulted in chemical reaction between the materials in each case. Alumina substrates were identified which withstood contact at the operating temperature of a molten regolith electrolysis cell (1600 C) for eight hours with little interaction or deformation. This represents an improvement over alumina grades currently in use and will provide a lifetime adequate for electrolysis experiments lasting 24 hours or more. Two types of non-oxide ceramics were also tested. It was found that they interacted to a limited degree with the melt resulting in little corrosion. These ceramics, Sic and BN, were not wetted as well as the oxides by the melt, and so remain possible materials for molten regolith handling. Tests wing longer holding periods and larger volumes of regolith are necessary to determine the ultimate performance of the tested ceramics.

Methodology of integrated land as containing transuranic; Metodologia de medida integrada de tierras con contenido de transuranidos

Energy Technology Data Exchange (ETDEWEB)

Correa Garces, E.; Saez Vergara, J. C.; Burgos Garcia, D.; Sancho Llerandi, C.

2011-07-01

The determination of the activity concentration of soil contaminated with transuranic on significant volumes is not trivial, is a technique that is necessary to evaluate the extent of large amounts of land (thousand m3) in restoration projects or to land contain americium or plutonium due to activities or incidents of the past.

Los Alamos National Laboratory Develops ''Quick to WIPP'' Strategy

International Nuclear Information System (INIS)

Jones, R.; Allen, G.; Kosiewicz, S.; Martin, B.; LANL; Nunz, J.; Biedscheid, J.; Sellmer, T.; Willis, J.; Orban, J.; Liekhus, K.; Djordjevic, S.

2003-01-01

The Cerro Grande forest fire in May of 2000 and the terrorist events of September 11, 2001 precipitated concerns of the vulnerability of legacy contact-handled (CH), high-wattage transuranic (TRU) waste stored at Los Alamos National Laboratory (LANL). An analysis of the 9,100 cubic meters of stored CH-TRU waste revealed that 400 cubic meters or 4.5% of the inventory represented 61% of the risk. The analysis further showed that this 400 cubic meters was contained in only 2,000 drums. These facts and the question ''How can the disposition of this waste to the Waste Isolation Pilot Plant (WIPP) be accelerated?'' formed the genesis of LANL's Quick to WIPP initiative

Repackaging of High Fissile TRU Waste at the Transuranic Waste Processing Center - 13240

Energy Technology Data Exchange (ETDEWEB)

Oakley, Brian; Heacker, Fred [WAI, TRU Waste Processing Center, 100 WIPP Road Lenoir City, TN 37771 (United States); McMillan, Bill [DOE, Oak Ridge Operations, Bldg. 2714, Oak Ridge, TN 37830 (United States)

2013-07-01

Twenty-six drums of high fissile transuranic (TRU) waste from Oak Ridge National Laboratory (ORNL) operations were declared waste in the mid-1980's and placed in storage with the legacy TRU waste inventory for future treatment and disposal at the Waste Isolation Pilot Plant (WIPP). Repackaging and treatment of the waste at the TRU Waste Packaging Center (TWPC) will require the installation of additional equipment and capabilities to address the hazards for handling and repackaging the waste compared to typical Contact Handled (CH) TRU waste that is processed at the TWPC, including potential hydrogen accumulation in legacy 6M/2R packaging configurations, potential presence of reactive plutonium hydrides, and significant low energy gamma radiation dose rates. All of the waste is anticipated to be repackaged at the TWPC and certified for disposal at WIPP. The waste is currently packaged in multiple layers of containers which presents additional challenges for repackaging activities due to the potential for the accumulation of hydrogen gas in the container headspace in quantities than could exceed the Lower Flammability Limit (LFL). The outer container for each waste package is a stainless steel 0.21 m{sup 3} (55-gal) drum which contains either a 0.04 m{sup 3} or 0.06 m{sup 3} (10-gal or 15-gal) 6M drum. The inner 2R container in each 6M drum is ∼12 cm (5 in) outside diameter x 30-36 cm (12-14 in) long and is considered to be a > 4 liter sealed container relative to TRU waste packaging criteria. Inside the 2R containers are multiple configurations of food pack cans, pipe nipples, and welded capsules. The waste contains significant quantities of high burn-up plutonium oxides and metals with a heavy weight percentage of higher atomic mass isotopes and the subsequent in-growth of significant quantities of americium. Significant low energy gamma radiation is expected to be present due to the americium in-growth. Radiation dose rates on inner containers are estimated

Evaluation of forms for the immobilization of high-level and transuranic wastes

International Nuclear Information System (INIS)

Schuman, R.P.; Cox, N.D.; Gibson, G.W.; Kelsey, P.V. Jr.

1982-08-01

A figure-of-merit (FOM) analysis has been made of a number of waste forms for solidifying both defense and commercial high-level reprocessing waste (HLW) and transuranic (TRU) wastes. The evaluation includes iron-enriched basalt (IEB), a fusion-produced glass-ceramic, which has not been included in other assessments. For HLW, concrete receives the highest FOM, but may not meet regulatory requirements; IEB and glass are the best choices of the materials that should easily meet regulatory requirements. Concrete waste forms are the best choice for TRU wastes, with IEB a close contender. 116 references, 3 figures, 112 tables

Predictions and implications of a poisson process model to describe corrosion of transuranic waste drums

International Nuclear Information System (INIS)

Lyon, B.F.; Holmes, J.A.; Wilbert, K.A.

1995-01-01

A risk assessment methodology is described in this paper to compare risks associated with immediate or near-term retrieval of transuranic (TRU) waste drums from bermed storage versus delayed retrieval. Assuming a Poisson process adequately describes corrosion, significant breaching of drums is expected to begin at - 15 and 24 yr for pitting and general corrosion, respectively. Because of this breaching, more risk will be incurred by delayed than by immediate retrieval

Long-range plan for buried transuranic waste studies at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Low, J.O.

1985-12-01

This document presents a plan to perform detailed studies of alternatives considered for the long-term management of buried transuranic waste at the Idaho National Engineering Laboratory (INEL). The studies will provide the technical basis for DOE to make a decision on the future management of that waste. Although the waste is currently being handled in an acceptable manner, new solutions are continually being researched to improve management techniques. Three alternatives are being considered: (a) leave the waste as is; (b) improve in situ confinement of the waste; and (c) retrieve, process, and certify the waste for disposal at a federal repository. Fourteen studies are described in this plan for Alternatives 2 and 3. The leave-as-is alternative involves continuing present procedures for managing the buried waste. An ongoing environmental surveillance program, a low-level-waste stabilization program, and enhanced subsurface migration studies begun in FY-1984 at the INEL will provide data for the decision-making process for the INEL buried TRU waste. These ongoing studies for the leave-as-is alternative are summarized in this plan in limited detail. The improved-confinement alternative involves leaving the waste in place, but providing additional protection against wind, water penetration, erosion, and plant and animal intrusion. Several studies proposed under this alternative will examine special techniques to immobilize or encapsulate the buried waste. An in situ grouting study was implemented at the INEL starting in FY-1985 and will be completed at the end of FY-1986 with the grouting of a simulated INEL buried TRU waste trench. Studies of the third alternative will investigate improved retrieval, processing, and certification techniques. New equipment, such as industrial manipulators and excavating machinery, will be tested in the retrieval studies. Processing and certification studies will examine rapidly changing or new technologies

Development of an Engineered Product Storage Concept for the UREX+1 Combined Transuranic/Lanthanide Product Streams

International Nuclear Information System (INIS)

McDeavitt, Sean M.; Downar, Thomas J.; Taiwo, Temitope A.; Williamson, Mark A.

2009-01-01

The U.S. Department of Energy is developing next generation processing methods to recycle uranium and transuranic (TRU) isotopes from spent nuclear fuel. The objective of the 3-year project described in this report was to develop near-term options for storing TRU oxides isolated through the uranium extraction (UREX+) process. More specifically, a Zircaloy matrix cermet was developed as a storage form for transuranics with the understanding that the cermet also has the ability to serve as a inert matrix fuel form for TRU burning after intermediate storage. The goals of this research projects were: (1) to develop the processing steps required to transform the effluent TRU nitrate solutions and the spent Xircaloy cladding into a zireonium matrix cermet storage form; and (2) to evaluate the impact of phenomena that govern durability of the storage form, material processing, and TRU utilization in fast reactor fuel. This report represents a compilation of the results generated under this program. The information is presented as a brief technical narrative in the following sections with appended papers, presentations and academic theses to provide a detailed review of the project's accomplishments

Levels, distribution and bioavailability of transuranic elements released in the Palomares accident (Spain).

Science.gov (United States)

Jiménez-Ramos, M C; Vioque, I; García-Tenorio, R; García León, M

2008-11-01

The current levels and distribution of the remaining transuranic contamination present in the terrestrial area affected by the nuclear Palomares accident have been evaluated through the determination of the Pu-isotopes and (241)Am concentrations in soils collected 35 years after the accident. In addition, after confirming that most of the contamination is present in particulate form, some bioavailability laboratory-based experiments, based on the use of single extractants, were performed as an essential step in order to study the behaviour of the Pu contamination in the soils from the affected areas.

Particle and solution phase depth distributions of transuranics and 55Fe in the North Pacific

International Nuclear Information System (INIS)

Livingston, H.D.; Mann, D.R.; Casso, S.A.; Schneider, D.L.; Surprenant, L.D.; Bowen, V.T.

1987-01-01

In situ large volume filtration and chemisorption techniques were used to collect samples from the North Pacific for radiochemical analyses of fallout transuranics and 55 Fe in filterable and filtered phases. The data cover several locations for surface collections and a detailed depth profile north of Hawaii at 30 0 N. The observed partition of these nuclides between suspended particulate and filtered phases is directly linked to the rates at which they are moved downward through the water column in association with sinking particles. Particulate phases in open ocean surface waters contain higher Pu than subsurface particulates. 241 Am was found to exhibit much stronger particle association in accord with its known greater particle reactivity. In the high Pu deep water layer, particle associated Pu dropped to close to 1% of total Pu concentration. Together with a correlated increase in the proportion of oxidized Pu in this layer close to the sediment-water interface, this is clear evidence of remobilization of Pu from particles at, or near to, the interface. 55 Fe distributions on filtered particulates indicate a much deeper depth distribution relative to the transuranics. This may reflect both a higher particle association reactivity in respect to scavenging and a longer exposure history to scavenging. (author)

Use of WIMS-E lattice code for prediction of the transuranic source term for spent fuel dose estimation

International Nuclear Information System (INIS)

Schwinkendorf, K.N.

1996-01-01

A recent source term analysis has shown a discrepancy between ORIGEN2 transuranic isotopic production estimates and those produced with the WIMS-E lattice physics code. Excellent agreement between relevant experimental measurements and WIMS-E was shown, thus exposing an error in the cross section library used by ORIGEN2

The effect of vibration on alpha radiolysis of transuranic (TRU) waste

International Nuclear Information System (INIS)

Zerwekh, A.; Kosiewicz, S.; Warren, J.

1993-01-01

This paper reports on previously unpublished scoping work related to the potential for vibration to redistribute radionuclides on transuranic (TRU) waste. If this were to happen, the amount of gases generated, including hydrogen, could be increased above the undisturbed levels. This could be an important consideration for transport of TRU wastes either at DOE sites or from them to a future repository, e.g., the Waste Isolation Pilot Plant (WIPP). These preliminary data on drums of real waste seem to suggest that radionuclide redistribution does not occur. However improvements in the experimental methodology are suggested to enhance safety of future experiments on real wastes as well as to provide more rigorous data

Handling of multiassembly sealed baskets between reactor storage and a remote handling facility

International Nuclear Information System (INIS)

Massey, J.V.; Kessler, J.H.; McSherry, A.J.

1989-06-01

The storage of multiple fuel assemblies in sealed (welded) dry storage baskets is gaining increasing use to augment at-reactor fuel storage capacity. Since this increasing use will place a significant number of such baskets on reactor sites, some initial downstream planning for their future handling scenarios for retrieving multi-assembly sealed baskets (MSBs) from onsite storage and transferring and shipping the fuel (and/or the baskets) to a federally operated remote handling facility (RHF). Numerous options or at-reactor and away-from-reactor handling were investigated. Materials handling flowsheets were developed along with conceptual designs for the equipment and tools required to handle and open the MSBs. The handling options were evaluated and compared to a reference case, fuel handling sequence (i.e., fuel assemblies are taken from the fuel pool, shipped to a receiving and handling facility and placed into interim storage). The main parameters analyzed are throughout, radiation dose burden and cost. In addition to evaluating the handling of MSBs, this work also evaluated handling consolidated fuel canisters (CFCs). In summary, the handling of MSBs and CFCs in the store, ship and bury fuel cycle was found to be feasible and, under some conditions, to offer significant benefits in terms of throughput, cost and safety. 14 refs., 20 figs., 24 tabs

Nuclear fuel handling apparatus

International Nuclear Information System (INIS)

Andrea, C.; Dupen, C.F.G.; Noyes, R.C.

1977-01-01

A fuel handling machine for a liquid metal cooled nuclear reactor in which a retractable handling tube and gripper are lowered into the reactor to withdraw a spent fuel assembly into the handling tube. The handling tube containing the fuel assembly immersed in liquid sodium is then withdrawn completely from the reactor into the outer barrel of the handling machine. The machine is then used to transport the spent fuel assembly directly to a remotely located decay tank. The fuel handling machine includes a decay heat removal system which continuously removes heat from the interior of the handling tube and which is capable of operating at its full cooling capacity at all times. The handling tube is supported in the machine from an articulated joint which enables it to readily align itself with the correct position in the core. An emergency sodium supply is carried directly by the machine to provide make up in the event of a loss of sodium from the handling tube during transport to the decay tank. 5 claims, 32 drawing figures

Vitrification of transuranic and beta-gamma contaminated solid wastes

International Nuclear Information System (INIS)

Dukes, M.D.

1980-06-01

Vitrification of solid transuranic contaminated (TRU) wastes alone and with high-level liquid wastes (HLLW) was studied. Homogeneous glasses containing 20 to 30 wt % ash were made by using glass frits previously developed at the Savannah River Plant and Pacific Northwest Laboratories. If the ash is vitrified along with the HLLW, 1.0 wt % as can be added to the waste forms without affecting their quality. This loading of ash is well above the loading required by the relative amounts of HLLW and TRU ash that will be processed at the Savannah River Plant. Vitrification of TRU-contaminated electropolishing sludges and high efficiency particular air filter materials along with HLLW would require an increase in the quantity of glass to be produced. However, if these TRU-contaminated solids were vitrified with the HLLW, the addition of low-level beta-gamma contaminated ash would require no further increase in glass production

W-026, transuranic waste (TRU) glovebox acceptance test report

International Nuclear Information System (INIS)

Leist, K.J.

1998-01-01

On July 18, 1997, the Transuranic (TRU) glovebox was tested using glovebox acceptance test procedure 13021A-86. The primary focus of the glovebox acceptance test was to examine control system interlocks, display menus, alarms, and operator messages. Limited mechanical testing involving the drum ports, hoists, drum lifter, compacted drum lifter, drum tipper, transfer car, conveyors, sorting table, lidder/delidder device and the TRU empty drum compactor were also conducted. As of February 25, 1998, 10 of the 102 test exceptions that affect the TRU glovebox remain open. These items will be tracked and closed via the WRAP Master Test Exception Database. As part of Test Exception resolution/closure the responsible individual closing the Test Exception performs a retest of the affected item(s) to ensure the identified deficiency is corrected, and, or to test items not previously available to support testing. Test exceptions are provided as appendices to this report

Some considerations in the handling of fluorine and the chlorine fluorides

International Nuclear Information System (INIS)

Farrar, R.L. Jr.; Barber, E.J.

1979-01-01

This paper reviews many considerations in the safe handling of fluorine and the chlorine fluorides. The physical, chemical, and toxicological properties of the materials are reviewed. Proper choice of materials of construction and materials in contact with the active gases are considered. The survey includes safe practices in design and operation of experiments and processes. Soda lime traps and caustic scrubbing are reviewed for fluorine disposal methods. Finally some explosive reactions and explosive situations are discussed

Overall strategy and program plan for management of radioactively contaminated liquid wastes and transuranic sludges at the Oak Ridge National Laboratory

International Nuclear Information System (INIS)

McNeese, L.E.; Berry, J.B.; Butterworth, G.E. III; Collins, E.D.; Monk, T.H.; Patton, B.D.; Snider, J.W.

1988-12-01

The use of hydrofracture was terminated after 1984, and LW concentrate has been accumulated and stored since that time. Currently, the volume of stored LW concentrate is near the safe fill limit for the 11 storage tanks in the active LW system, and significant operational constraints are being experienced. The tanks that provide the storage capacity of the active LW system contain significant volumes of TRU sludges that have been designated remote-handled transuranic (RH-TRU) wastes because of associated quantities of other radioisotopes, including 90 Sr and 137 Cs. Thirty-three additional tanks, which are inactive, also contain significant volumes of TRU waste and radioactive LW. A lack of adequate storage volume for LW jeopardizes ORNL's ability to ensure continued conduct of research and development (RandD) activities that generate LW because an unexpected operational incident could quickly deplete the remaining storage volume. Accordingly, a planning team comprised of staff members from the ORNL Nuclear and Chemical Waste Programs (NCWP) was created for developing recommended actions to be taken for management of LW. A program plan is presented which outlines work required for the development of a disposal method for each of the likely future waste streams associated with LW management and the disposal of the bulk of the resulting solid waste on the ORR. 8 refs., 20 figs., 12 tabs

Preliminary Safety Analysis Report for the Transuranic Storage Area Retrieval Enclosure at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

1993-03-01

This Transuranic Storage Area Retrieval Enclosure Preliminary Safety Analysis Report was completed as required by DOE Order 5480.23. The purpose of this document is to construct a safety basis that supports the design and permits construction of the facility. The facility has been designed to the requirements of a Radioactive Solid Waste Facility presented in DOE Order 6430.1A

Full-scale retrieval of simulated buried transuranic waste

International Nuclear Information System (INIS)

Valentich, D.J.

1993-09-01

This report describes the results of a field test conducted to determine the effectiveness of using conventional type construction equipment for the retrieval of buried transuranic (TRU) waste. A cold (nonhazardous and nonradioactive) test pit (1,100 yd 3 volume) was constructed with boxes and drums filled with simulated waste materials, such as metal, plastic, wood, concrete, and sludge. Large objects, including truck beds, tanks, vaults, pipes, and beams, were also placed in the pit. These materials were intended to simulate the type of wastes found in TRU buried waste pits and trenches. A series of commercially available equipment items, such as excavators and tracked loaders outfitted with different end effectors, were used to remove the simulated waste. Work was performed from both the abovegrade and belowgrade positions. During the demonstration, a number of observations, measurements, and analyses were performed to determine which equipment was the most effective in removing the waste. The retrieval rates for the various excavation techniques were recorded. The inherent dust control capabilities of the excavation methods used were observed. The feasibility of teleoperating reading equipment was also addressed

The transuranic waste management program at Savannah River

International Nuclear Information System (INIS)

D'Ambrosia, J.

1986-01-01

Defense transuranic waste at the Savannah River site results from the Department of Energy's national defense activities, including the operation of production reactors, fuel reprocessing plants, and research and development activities. TRU waste has been retrievably stored at the Savannah River Plant since 1974 awaiting disposal. The Waste Isolation Pilot Plant, now under construction in New Mexico, is a research and development facility for demonstrating the safe disposal of defense TRU waste, including that in storage at the Savannah River Plant. The major objective of the TRU Program at SR is to support the TRU National Program, which is dedicated to preparing waste for, and emplacing waste in, the WIPP. Thus, the SR Program also supports WIPP operations. The SR site specific goals are to phase out the indefinite storage of TRU waste, which has been the mode of waste management since 1974, and to dispose of the defense TRU waste. This paper describes the specific activities at SR which will provide for the disposal of this TRU waste

TRUPACT-II Content Codes (TRUCON), Revision 8 and list of chemicals and materials in TRUCON (chemical list), Revision 7

International Nuclear Information System (INIS)

1996-03-01

The Transuranic Package Transporter (TRUPACT-II) Content Codes document (TRUCON) represents the development of a new content code system for shipping contact handled transuranic (CH-TRU) waste in TRUPACT-II. It will be used to convert existing waste forms, content codes, and any other identification codes into a system that is uniform throughout for all the Department of Energy (DOE) sites. These various codes can be grouped under the newly formed shipping content codes without any loss of waste characterization information. The TRUCON document provides a parametric description for each content code for waste generated and compiles this information for all ten DOE sites. Compliance with waste generation, processing and certification procedures at the sites (outlined in the TRUCON document for each content code) ensures that prohibited waste forms are not present in the waste. The content code essentially gives a description of the CH-TRU waste material in terms of processes and packaging, and the generation location. This helps to provide cradle-to-grave traceability of the waste material so that the various actions required to assess its qualification as payload for the TRUPACT-II package can be performed

Position for determining gas-phase volatile organic compound concentrations in transuranic waste containers. Revision 2

Energy Technology Data Exchange (ETDEWEB)

Connolly, M.J.; Liekhus, K.J. [Lockheed Martin Idaho Technologies Co., Idaho Falls, ID (United States). Idaho National Engineering and Environmental Lab.; Djordjevic, S.M.; Loehr, C.A.; Spangler, L.R. [Benchmark Environmental Corp. (United States)

1998-06-01

In the conditional no-migration determination (NMD) for the test phase of the Waste Isolation Pilot Plant (WIPP), the US Environmental Protection Agency (EPA) imposed certain conditions on the US Department of Energy (DOE) regarding gas phase volatile organic compound (VOC) concentrations in the void space of transuranic (TRU) waste containers. Specifically, the EPA required the DOE to ensure that each waste container has no layer of confinement that contains flammable mixtures of gases or mixtures of gases that could become flammable when mixed with air. The EPA also required that sampling of the headspace of waste containers outside inner layers of confinement be representative of the entire void space of the container. The EPA stated that all layers of confinement in a container would have to be sampled until DOE can demonstrate to the EPA that sampling of all layers is either unnecessary or can be safely reduced. A test program was conducted at the Idaho National Engineering and Environmental Laboratory (INEEL) to demonstrate that the gas phase VOC concentration in the void space of each layer of confinement in vented drums can be estimated from measured drum headspace using a theoretical transport model and that sampling of each layer of confinement is unnecessary. This report summarizes the studies performed in the INEEL test program and extends them for the purpose of developing a methodology for determining gas phase VOC concentrations in both vented and unvented TRU waste containers. The methodology specifies conditions under which waste drum headspace gases can be said to be representative of drum gases as a whole and describes a method for predicting drum concentrations in situations where the headspace concentration is not representative. The methodology addresses the approach for determining the drum VOC gas content for two purposes: operational period drum handling and operational period no-migration calculations.

Position for determining gas phase volatile organic compound concentrations in transuranic waste containers. Revision 1

International Nuclear Information System (INIS)

Connolly, M.J.; Liekhus, K.J.; Djordjevic, S.M.; Loehr, C.A.; Spangler, L.R.

1995-08-01

In the conditional no-migration determination (NMD) for the test phase of the Waste Isolation Pilot Plant (WIPP), the US Environmental Protection Agency (EPA) imposed certain conditions on the US Department of Energy (DOE) regarding gas phase volatile organic compound (VOC) concentrations in the void space of transuranic (TRU) waste containers. Specifically, the EPA required the DOE to ensure that each waste container has no layer of confinement that contains flammable mixtures of gases or mixtures of gases that could become flammable when mixed with air. The EPA also required that sampling of the headspace of waste containers outside inner layers of confinement be representative of the entire void space of the container. The EPA stated that all layers of confinement in a container would have to be sampled until DOE can demonstrate to the EPA that sampling of all layers is either unnecessary or can be safely reduced. A test program was conducted at the Idaho National Engineering Laboratory (INEL) to demonstrate that the gas phase VOC concentration in the void space of each layer of confinement in vented drums can be estimated from measured drum headspace using a theoretical transport model and that sampling of each layer of confinement is unnecessary. This report summarizes the studies performed in the INEL test program and extends them for the purpose of developing a methodology for determining gas phase VOC concentrations in both vented and unvented TRU waste containers. The methodology specifies conditions under which waste drum headspace gases can be said to be representative of drum gases as a whole and describes a method for predicting drum concentrations in situations where the headspace concentration is not representative. The methodology addresses the approach for determining the drum VOC gas content for two purposes: operational period drum handling and operational period no-migration calculations

Position for determining gas-phase volatile organic compound concentrations in transuranic waste containers. Revision 2

International Nuclear Information System (INIS)

Connolly, M.J.; Liekhus, K.J.

1998-06-01

In the conditional no-migration determination (NMD) for the test phase of the Waste Isolation Pilot Plant (WIPP), the US Environmental Protection Agency (EPA) imposed certain conditions on the US Department of Energy (DOE) regarding gas phase volatile organic compound (VOC) concentrations in the void space of transuranic (TRU) waste containers. Specifically, the EPA required the DOE to ensure that each waste container has no layer of confinement that contains flammable mixtures of gases or mixtures of gases that could become flammable when mixed with air. The EPA also required that sampling of the headspace of waste containers outside inner layers of confinement be representative of the entire void space of the container. The EPA stated that all layers of confinement in a container would have to be sampled until DOE can demonstrate to the EPA that sampling of all layers is either unnecessary or can be safely reduced. A test program was conducted at the Idaho National Engineering and Environmental Laboratory (INEEL) to demonstrate that the gas phase VOC concentration in the void space of each layer of confinement in vented drums can be estimated from measured drum headspace using a theoretical transport model and that sampling of each layer of confinement is unnecessary. This report summarizes the studies performed in the INEEL test program and extends them for the purpose of developing a methodology for determining gas phase VOC concentrations in both vented and unvented TRU waste containers. The methodology specifies conditions under which waste drum headspace gases can be said to be representative of drum gases as a whole and describes a method for predicting drum concentrations in situations where the headspace concentration is not representative. The methodology addresses the approach for determining the drum VOC gas content for two purposes: operational period drum handling and operational period no-migration calculations

Remediation of ultra low level of transuranics from potable water using hybrid materials

International Nuclear Information System (INIS)

Singhal, R.K.; Basu, H.; Reddy, A.V.R.

2015-01-01

In case of nuclear accidents like Daiichi Nuclear Power Plant (NPP) Fukushima, Japan (11 March, 2011) and nuclear accidents like Chernobyl, USSR (March, 1986), where large amount of activity spread in public domain necessitate the need of development of new material which can efficiently remove transuranic from potable water without disturbing its water quality. Three different types of natural sorbents were developed using natural siliceous material, sodium alginate and impregnation of goethite in alginate matrix. Experiments were carried out for decontamination of americium and plutonium by using Calcium Alginate (Cal-Alg) and Goethite impregnated Cal-Alg (Geo-Cal-Alg) respectively

FFTF [Fast Flux Test Facility] fuel handling experience (1979--1986)

International Nuclear Information System (INIS)

Romrell, D.M.; Art, D.M.; Redekopp, R.D.; Waldo, J.B.

1987-05-01

The Fast Flux Test Facility (FFTF)is a 400 MW (th) sodium-cooled fast flux test reactor located on the Hanford Site in southeastern Washington State. The FFTF is operated by the Westinghouse Hanford Company for the United States Department of Energy. The FFTF is a three loop plant designed primarily for the purpose of testing full-scale core components in an environment prototypic of future liquid metal reactors. The plant design emphasizes features to enhance this test capability, especially in the area of the core, reactor vessel, and refueling system. Eight special test positions are provided in the vessel head to permit contact instrumented experiments to be installed and irradiated. These test positions effectively divide the core into three sectors. Each sector requires its own In-Vessel Handling Machine (IVHM) to access all the core positions. Since the core and the in-vessel refueling components are submerged under sodium, all handling operations must be performed blind. This puts severe requirements on the positioning ability are reliability of the refueling components. This report addresses the operating experience with the fuel handling system from initial core loading in November, 1979 through 1986. This includes 9 refueling cycles. 2 refs., 8 figs

Stored Transuranic Waste Management Program at the Idaho National Engineering Laboratory

International Nuclear Information System (INIS)

Clements, T.L.

1996-01-01

Since 1970, INEL has provided interim storage capacity for transuranic (TRU)-contaminated wastes generated by activities supporting US national defense needs. About 60% of the nation's current inventory of TRU-contaminated waste is stored at INEL, awaiting opening of the Waste Isolation Pilot Plant (WIPP), the designated federal repository. A number of activities are currently underway for enhancing current management capabilities, conducting projects that support local and national TRU management activities, and preparing for production-level waste retrieval, characterization, examination, certification, and shipment of untreated TRU waste to WIPP in April 1998. Implementation of treatment capability is planned in 2003 to achieve disposal of all stored TRU-contaminated waste by a target date of December 31, 2015, but no later than December 31, 2018

Multi-recycling of transuranic elements in a PWR assembly with reduced fuel rod diameter

International Nuclear Information System (INIS)

Chambers, Alex; Ragusa, Jean C.

2014-01-01

Highlights: • Study of multiple recycling passes of transuranic elements: (a) without exceeding 5 wt.% on U-235 enrichment; (b) using PWR fuel assemblies compatible with current reactor core internals. • Isotopic concentrations tend towards an equilibrium after 15 recycle passes, suggesting that thermal recycling may be continued beyond that point. • Radiotoxicity comparisons for once-through UOX, once-recycle MOX-Pu, and multiple recycle passes of MOX-PuNpAm and MOX-PuNpAmCm are presented. - Abstract: This paper examines the multi-recycling of transuranic (TRU) elements (Pu-Np-Am-Cm) in standard Pressurized Water Reactor (PWR) assemblies. The original feed of TRU comes from legacy spent UOX fuel. For all subsequent recycling passes, TRU elements from the previous generation are employed, supplemented by TRU from legacy UOX fuel, as needed. The design criteria include: 235 U enrichment requirements to remain below 5 w/o, TRU loading limits to avoid return to criticality under voided conditions, and assembly power peaking factors. In order to carry out multiple recycling passes within the design envelope, additional neutron moderation is required and achieved by reducing the fuel pellet diameter by about 13%, thus keeping the assembly design compatible with current PWR core internals. TRU transmutation rates and long-term ingestion radiotoxicity results are presented for 15 recycling passes and compared to standard UOX and MOX once-through cycles. The results also show that TRU fuel isotopics and radiotoxicity tend towards an equilibrium, enabling further additional recycling passes

The Los Alamos National Laboratory Transuranic Waste Retireval Project

International Nuclear Information System (INIS)

Montoya, G.M.; Christensen, D.V.; Stanford, A.R.

1997-01-01

This paper presents the status of the Los Alamos National Laboratory (LANL) project for remediation of transuranic (TRU) and TRU mixed waste from Pads 1, 2, and 4. Some of the TRU waste packages retrieved from Pad I are anticipated to be part of LANL's initial inventory to be shipped to the Waste Isolation Pilot Plant (WIPP) in April 1998. The TRU Waste Inspectable Storage Project (TWISP) was initiated in February 1993 in response to the New Mexico Environment Department's (NMED's) Consent Agreement for Compliance Order, ''New Mexico Hazardous Waste Agreement (NMHWA) 93-03.'' The TWISP involves the recovery of approximately 16,865 TRU and TRU-mixed waste containers currently under earthen cover on Pads 1, 2, and 4 at Technical Area 54, Area G, and placement of that waste into inspectable storage. All waste will be moved into inspectable storage by September 30, 2003. Waste recovery and storage operations emphasize protection of worker safety, public health, and the environment

Design and evaluation of a new ergonomic handle for instruments in minimally invasive surgery.

Science.gov (United States)

Sancibrian, Ramon; Gutierrez-Diez, María C; Torre-Ferrero, Carlos; Benito-Gonzalez, Maria A; Redondo-Figuero, Carlos; Manuel-Palazuelos, Jose C

2014-05-01

Laparoscopic surgery techniques have been demonstrated to provide massive benefits to patients. However, surgeons are subjected to hardworking conditions because of the poor ergonomic design of the instruments. In this article, a new ergonomic handle design is presented. This handle is designed using ergonomic principles, trying to provide both more intuitive manipulation of the instrument and a shape that reduces the high-pressure zones in the contact with the surgeon's hand. The ergonomic characteristics of the new handle were evaluated using objective and subjective studies. The experimental evaluation was performed using 28 volunteers by means of the comparison of the new handle with the ring-handle (RH) concept in an instrument available on the market. The volunteers' muscle activation and motions of the hand, wrist, and arm were studied while they performed different tasks. The data measured in the experiment include electromyography and goniometry values. The results obtained from the subjective analysis reveal that most volunteers (64%) preferred the new prototype to the RH, reporting less pain and less difficulty to complete the tasks. The results from the objective study reveal that the hyperflexion of the wrist required for the manipulation of the instrument is strongly reduced. The new ergonomic handle not only provides important ergonomic advantages but also improves the efficiency when completing the tasks. Compared with RH instruments, the new prototype reduced the high-pressure areas and the extreme motions of the wrist. Copyright © 2014 Elsevier Inc. All rights reserved.

TRU assay system and measurements

International Nuclear Information System (INIS)

Brodzinski, R.L.

1984-02-01

The measurement of the transuranic content of nuclear products or process residues has become increasingly important for the recovery of fissionable material from spent fuel elements, the identification of commercial fuel elements which have not yet reached full burnup, the measurement and recovery of transuranics from discarded or stored waste materials, the determination of the transuranic content in high gamma activity waste material scheduled for disposal, compliance with 10CFR61 by land burial operators/shippers, and the satisfaction of accountability requirements. Active neutron interrogation techniques measure either the prompt neutrons or the beta delayed neutrons from fission products following induced fission. These techniques normally only measure fissile transuranics ( 235 U, 239 Pu, and 241 Pu) and are commonly applied only to contact handleable waste. Passive neutron interrogation techniques, on the other hand, are capable of measuring all transuranics except 235 U with adequate sensitivity and will work on both contact handleable and high gamma activity wastes. Since the passive techniques are senstitive to a wider spectrum of transuranic isotopes than the active techniques, substantially less complex and less expensive than the active systems, and they have proven techniques for measuring small quantities of TRU in high gamma activity packages, the passive neutron TRU assay technology was chosen for development into the instruments discussed in this paper

Assessment of change in shallow land burial limits for defense transuranic waste

International Nuclear Information System (INIS)

Cohen, J.J.; Smith, C.F.; Spaeth, M.E.; Ciminesi, F.J.; Dickman, P.T.; O'Neal, D.A.

1983-03-01

There is an emerging consensus within the waste management technical community that the current concentration limit of 10 nCi/g for shallow land burial (SLB) of transuranic (TRU) waste is excessively restrictive. A concentration limit for SLB in the range of 100 to 1000 nCi/g is reasonable and justifiable based upon these reasons: Resultant increase in collective radiation dose (total population dose) would be very small, and the net detriment to public health would be negligible. Increasing the limit is cost-effective and could save hundreds of millions of dollars for the national economy over time. The hazard resulting from the increased SLB limit for TRU would be significantly less than that due to many naturally occurring mineral deposits and/or human activities. Expenditures directed toward health and safety conform to the economic law of diminishing returns: as the absolute expenditure increases, the marginal return decreases. Excessive restriction of the TRU concentration limit for SLB needlessly diverts limited resources (time, talent, and money) from other areas of health and safety where they might be more beneficially applied. Despite considerable effort, this study did not find any compelling technical argument to maintain the limit for TRU in SLB at 10 nCi/g. Subsequent to the initial preparation of this document, the US Department of Energy issued DOE Order 5820 which raises the administrative disposal limit for transuranic wastes from 10 nCi/g to 100 nCi/g. In addition, the US Nuclear Regulatory Commission has subsequently proposed and adopted a revised version of regulation 10 CFR 61 in which the disposal limit for shallow land burial of Category C (intruder protected) waste is set at 100 nCi/g

Waste management facilities cost information for transportation of radioactive and hazardous materials

International Nuclear Information System (INIS)

Feizollahi, F.; Shropshire, D.; Burton, D.

1995-06-01

This report contains cost information on the U.S. Department of Energy (DOE) Complex waste streams that will be addressed by DOE in the programmatic environmental impact statement (PEIS) project. It describes the results of the task commissioned by DOE to develop cost information for transportation of radioactive and hazardous waste. It contains transportation costs for most types of DOE waste streams: low-level waste (LLW), mixed low-level waste (MLLW), alpha LLW and alpha MLLW, Greater-Than-Class C (GTCC) LLW and DOE equivalent waste, transuranic (TRU) waste, spent nuclear fuel (SNF), and hazardous waste. Unit rates for transportation of contact-handled ( 200 mrem/hr contact dose) radioactive waste are estimated. Land transportation of radioactive and hazardous waste is subject to regulations promulgated by DOE, the U.S. Department of Transportation (DOT), the U.S. Nuclear Regulatory Commission (NRC), and state and local agencies. The cost estimates in this report assume compliance with applicable regulations

Evaluation of alternatives for high-level and transuranic radioactive- waste disposal standards

International Nuclear Information System (INIS)

Klett, R.D.; Gruebel, M.M.

1992-12-01

The remand of the US Environmental Protection Agency's long-term performance standards for radioactive-waste disposal provides an opportunity to suggest modifications that would make the regulation more defensible and remove inconsistencies yet retain the basic structure of the original rule. Proposed modifications are in three specific areas: release and dose limits, probabilistic containment requirements, and transuranic-waste disposal criteria. Examination of the modifications includes discussion of the alternatives, demonstration of methods of development and implementation, comparison of the characteristics, attributes, and deficiencies of possible options within each area, and analysis of the implications for performance assessments. An additional consideration is the impact on the entire regulation when developing or modifying the individual components of the radiological standards

Isolated contact urticaria caused by immunoglobulin E-mediated fish allergy.

Science.gov (United States)

Onesimo, Roberta; Giorgio, Valentina; Pill, Stefania; Monaco, Serena; Sopo, Stefano Miceli

2012-01-01

Fish is a common cause of food allergy. The reactions usually occur after its ingestion. In most immunoglobulin E-mediated reactions, the allergens are gastroresistant and heat-stable proteins of low molecularweight (parvalbumin). On the other hand, isolated contact urticaria following the handling of raw fish but without symptoms after its ingestion was found among cooks and professional fish handlers. In these cases, the fish allergens are gastrosensitive and thermolabile, as demonstrated by the decrease in the diameter of the wheal in the skin-prick test using cooked fish. To the best of our knowledge isolated fish contact urticaria in children has not been previously reported. We analyze the features of three pediatric cases of contact urticaria from cod (one of them was sensitized to parvalbumin), with tolerance after ingestion of this fish on oral food challenge.

Mock-up test on key components of ITER blanket remote handling system

International Nuclear Information System (INIS)

Takeda, Nobukazu; Kakudate, Satoshi; Nakahira, Masataka; Matsumoto, Yasuhiro; Taguchi, Koh; Kozaka, Hiroshi; Shibanuma, Kiyoshi; Tesini, Alessandro

2009-01-01

The maintenance operation of the ITER in-vessel component, such as a blanket and divertor, must be executed by the remote equipment because of the high gamma-ray environment. During the Engineering Design Activity (EDA), the Japan Atomic Energy Agency (then called as Japan Atomic Energy Research Institute) had been fabricated the prototype of the vehicle manipulator system for the blanket remote handling and confirmed feasibility of this system including automatic positioning of the blanket and rail deployment procedure of the articulated rail. The ITER agreement, which entered into force in the last year, formally decided that Japan will procure the blanket remote handling system and the JAEA, as the Japanese Domestic Agency, is continuing several R and Ds so that the system can be procured smoothly. The residual key issues after the EDA are rail connection and cable handling. The mock-ups of the rail connection mechanism and the cable handling system were fabricated from the last year and installed at the JAEA Naka Site in this March. The former was composed of the rail connecting mechanism, two rail segments and their handling systems. The latter one utilized a slip ring, which implemented 80 lines for power and 208 lines for signal, because there is an electrical contact between the rotating spool and the fixed base. The basic function of these systems was confirmed through the mock-up test. The rail connection mechanism, for example, could accept misalignment of 1.5-2 mm at least. The future test plan is also mentioned in the paper.

An HVAC [heating, ventilation, and air-conditioning] fault-tree analysis for WIPP [Waste Isolation Pilot Plant] integrated risk assessment

International Nuclear Information System (INIS)

Kirby, P.N.; Iacovino, J.M.

1990-01-01

In order to evaluate the public health risk of potential radioactive releases from operation of the Waste Isolation Pilot Plant (WIPP), a probabilistic risk assessment of waste-handling operations was conducted. One major aspect of this risk assessment involved fault-tree analysis of the plant heating, ventilation, and air-conditioning (HVAC) systems, which constitute the final barrier between waste-handling operations and the environment. The WIPP site is designed to receive and store two types of waste: contact-handled transuranic (CH TRU) wastes to be shipped in 208-ell drums and remote-handled (RH) TRU wastes to be shipped in shielded casks. The identification of accident sequences for CH waste operations revealed no identified accidents that could release significant radioactive particulates to the environment without a failure in the HVAC systems. When the HVAC fault-tree results were combined with other critical system fault trees and the analysis of waste-handling accident sequences, the approximation of the overall WIPP plant risk due to airborne releases was determined to be 2.6 x 10 -7 fatalities per year for the population within a 50-mile radius of the WIPP site. This risk was demonstrated to be well below the risk of fatality from other voluntary and involuntary activities for the population within the vicinity of the WIPP

Recommendations for cask features for robotic handling from the Advanced Handling Technology Project

International Nuclear Information System (INIS)

Drotning, W.

1991-02-01

This report describes the current status and recent progress in the Advanced Handling Technology Project (AHTP) initiated to explore the use of advanced robotic systems and handling technologies to perform automated cask handling operations at radioactive waste handling facilities, and to provide guidance to cask designers on the impact of robotic handling on cask design. Current AHTP tasks have developed system mock-ups to investigate robotic manipulation of impact limiters and cask tiedowns. In addition, cask uprighting and transport, using computer control of a bridge crane and robot, were performed to demonstrate the high speed cask transport operation possible under computer control. All of the current AHTP tasks involving manipulation of impact limiters and tiedowns require robotic operations using a torque wrench. To perform these operations, a pneumatic torque wrench and control system were integrated into the tool suite and control architecture of the gantry robot. The use of captured fasteners is briefly discussed as an area where alternative cask design preferences have resulted from the influence of guidance for robotic handling vs traditional operations experience. Specific robotic handling experiences with these system mock-ups highlight a number of continually recurring design principles: (1) robotic handling feasibility is improved by mechanical designs which emphasize operation with limited dexterity in constrained workspaces; (2) clearances, tolerances, and chamfers must allow for operations under actual conditions with consideration for misalignment and imprecise fixturing; (3) successful robotic handling is enhanced by including design detail in representations for model-based control; (4) robotic handling and overall quality assurance are improved by designs which eliminate the use of loose, disassembled parts. 8 refs., 15 figs

Soil Sampling Plan for the transuranic storage area soil overburden and final report: Soil overburden sampling at the RWMC transuranic storage area

International Nuclear Information System (INIS)

Stanisich, S.N.

1994-12-01

This Soil Sampling Plan (SSP) has been developed to provide detailed procedural guidance for field sampling and chemical and radionuclide analysis of selected areas of soil covering waste stored at the Transuranic Storage Area (TSA) at the Idaho National Engineering Laboratory's (INEL) Radioactive Waste Management Complex (RWMC). The format and content of this SSP represents a complimentary hybrid of INEL Waste Management--Environmental Restoration Program, and Comprehensive Environmental Response, Compensation and Liability Act (CERCLA) Remedial Investigation/Feasibility Study (RI/FS) sampling guidance documentation. This sampling plan also functions as a Quality Assurance Project Plan (QAPP). The QAPP as a controlling mechanism during sampling to ensure that all data collected are valid, reliabile, and defensible. This document outlines organization, objectives and quality assurance/quality control (QA/QC) activities to achieve the desired data quality goals. The QA/QC requirements for this project are outlined in the Data Collection Quality Assurance Plan (DCQAP) for the Buried Waste Program. The DCQAP is a program plan and does not outline the site specific requirements for the scope of work covered by this SSP

Case studies of corrosion of mixed waste and transuranic waste drums

International Nuclear Information System (INIS)

Kosiewicz, S.T.

1993-01-01

This paper presents three case studies of corrosion of waste drums at the Los Alamos National Laboratory (LANL). Corrosion was not anticipated by the waste generators, but occurred because of subtle chemical or physical mechanisms. In one case, drums of a cemented transuranic (TRU) sludge experienced general and pitting corrosion. In the second instance, a chemical from a commercial paint stripper migrated from its primary containment drums to chemically attack overpack drums made of mild carbon steel. In the third case, drums of mixed low level waste (MLLW) soil corroded drum packaging even though the waste appeared to be dry when it was placed in the drums. These case studies are jointly discussed as ''lessons learned'' to enhance awareness of subtle mechanisms that can contribute to the corrosion of radioactive waste drums during interim storage

Environmental Cleanup of the East Tennessee Technology Park Year One - Execution with Certainty SM - 13120

Energy Technology Data Exchange (ETDEWEB)

Schubert, A.L. [URS - CH2M Oak Ridge LLC, P.O. Box 4699, Oak Ridge, TN 37831-7294 (United States)

2013-07-01

On August 1, 2011, URS - CH2M Oak Ridge LLC (UCOR) began its five-year, $1.4 billion cleanup of the East Tennessee Technology Park (ETTP), located on the U.S. Department of Energy's (DOE) Oak Ridge Reservation in Tennessee. UCOR will close out cleanup operations that began in 1998 under a previous contract. When the Contract Base scope of work [1] is completed in 2016, the K-25 gaseous diffusion building will have been demolished and all waste dispositioned, demolition will have started on the K-27 gaseous diffusion building, all contact-handled and remote-handled transuranic waste in inventory (approximately 500 cubic meters) will have been transferred to the Transuranic Waste Processing Center, previously designated 'No-Path-To-Disposition Waste' will have been dispositioned to the extent possible, and UCOR will have managed DOE Office of Environmental Management (EM)- owned facilities at ETTP, Oak Ridge National Laboratory (ORNL), and the Y-12 National Security Complex in a safe and cost-effective manner. Since assuming its responsibilities as the ETTP cleanup contractor, UCOR has completed its life-cycle Performance Measurement Baseline; received its Earned Value Management System (EVMS) certification; advanced the deactivation and demolition (D and D) of the K-25 gaseous diffusion building; recovered and completed the Tank W-1A and K-1070-B Burial Ground remediation projects; characterized, packaged, and shipped contact-handled transuranic waste to the Transuranic Waste Processing Center; disposed of more than 90,000 cubic yards of cleanup waste while managing the Environmental Management Waste Management Facility (EMWMF); and provided operations, surveillance, and maintenance activities at DOE EM facilities at ETTP, ORNL, and the Y-12 National Security Complex. Project performance as of December 31, 2012 has been excellent: - Cost Performance Index - 1.06; - Schedule Performance Index - 1.02. At the same time, since safety is the foundation of

Converting Simulated Sodium-bearing Waste into a Single Solid Waste Form by Evaporation: Laboratory- and Pilot-Scale Test Results on Recycling Evaporator Overheads

Energy Technology Data Exchange (ETDEWEB)

Griffith, D.; D. L. Griffith; R. J. Kirkham; L. G. Olson; S. J. Losinski

2004-01-01

Conversion of Idaho National Engineering and Environmental Laboratory radioactive sodium-bearing waste into a single solid waste form by evaporation was demonstrated in both flask-scale and pilot-scale agitated thin film evaporator tests. A sodium-bearing waste simulant was adjusted to represent an evaporator feed in which the acid from the distillate is concentrated, neutralized, and recycled back through the evaporator. The advantage to this flowsheet is that a single remote-handled transuranic waste form is produced in the evaporator bottoms without the generation of any low-level mixed secondary waste. However, use of a recycle flowsheet in sodium-bearing waste evaporation results in a 50% increase in remote-handled transuranic volume in comparison to a non-recycle flowsheet.

Safety evaluation for packaging (onsite) for concrete-shielded RHTRU waste drum for the 327 postirradiation testing laboratory

Energy Technology Data Exchange (ETDEWEB)

Adkins, H.E.

1996-10-29

This safety evaluation for packaging authorizes onsite transport of Type B quantities of radioactive material in the Concrete- Shielded Remote-Handled Transuranic Waste (RH TRU) Drum per WHC-CM-2-14, Hazardous Material Packaging and Shipping. The drum will be used for transport of 327 Building legacy waste from the 300 Area to the Transuranic Waste Storage and Assay Facility in the 200 West Area and on to a Solid Waste Storage Facility, also in the 200 Area.

Consequences of occupational food-related hand dermatoses with a focus on protein contact dermatitis

DEFF Research Database (Denmark)

Vester, Lotte; Thyssen, Jacob P; Menné, Torkil

2012-01-01

Background. Protein contact dermatitis is a frequent disorder among hand eczema patients who have occupational food contact. Knowledge about the consequences of having protein contact dermatitis is lacking. Objectives. To investigate the consequences of having occupational skin disease on the hands...... resulting from food handling, with a focus on protein contact dermatitis. Material and methods. One hundred and seventy-eight patients who were identified as having skin disease related to occupational food exposure and who answered a questionnaire concerning the consequences of their skin disease were......%, respectively, of the patients with other occupational food-related hand dermatoses (p = 0.02). Sixty-two per cent and 43%, respectively, had to change job because of skin problems (p = 0.02). Atopic dermatitis was equally common in the two groups. Conclusion. We found that the patients with protein contact...

Multi-recycling of transuranic elements in a PWR assembly with reduced fuel rod diameter

Energy Technology Data Exchange (ETDEWEB)

Chambers, Alex, E-mail: acchamb@gmail.com; Ragusa, Jean C., E-mail: jean.ragusa@tamu.edu

2014-04-01

Highlights: • Study of multiple recycling passes of transuranic elements: (a) without exceeding 5 wt.% on U-235 enrichment; (b) using PWR fuel assemblies compatible with current reactor core internals. • Isotopic concentrations tend towards an equilibrium after 15 recycle passes, suggesting that thermal recycling may be continued beyond that point. • Radiotoxicity comparisons for once-through UOX, once-recycle MOX-Pu, and multiple recycle passes of MOX-PuNpAm and MOX-PuNpAmCm are presented. - Abstract: This paper examines the multi-recycling of transuranic (TRU) elements (Pu-Np-Am-Cm) in standard Pressurized Water Reactor (PWR) assemblies. The original feed of TRU comes from legacy spent UOX fuel. For all subsequent recycling passes, TRU elements from the previous generation are employed, supplemented by TRU from legacy UOX fuel, as needed. The design criteria include: {sup 235}U enrichment requirements to remain below 5 w/o, TRU loading limits to avoid return to criticality under voided conditions, and assembly power peaking factors. In order to carry out multiple recycling passes within the design envelope, additional neutron moderation is required and achieved by reducing the fuel pellet diameter by about 13%, thus keeping the assembly design compatible with current PWR core internals. TRU transmutation rates and long-term ingestion radiotoxicity results are presented for 15 recycling passes and compared to standard UOX and MOX once-through cycles. The results also show that TRU fuel isotopics and radiotoxicity tend towards an equilibrium, enabling further additional recycling passes.

Prey handling using whole-body fluid dynamics in batoids.

Science.gov (United States)

Wilga, Cheryl D; Maia, Anabela; Nauwelaerts, Sandra; Lauder, George V

2012-02-01

Fluid flow generated by body movements is a foraging tactic that has been exploited by many benthic species. In this study, the kinematics and hydrodynamics of prey handling behavior in little skates, Leucoraja erinacea, and round stingrays, Urobatis halleri, are compared using kinematics and particle image velocimetry. Both species use the body to form a tent to constrain the prey with the pectoral fin edges pressed against the substrate. Stingrays then elevate the head, which increases the volume between the body and the substrate to generate suction, while maintaining pectoral fin contact with the substrate. Meanwhile, the tip of the rostrum is curled upwards to create an opening where fluid is drawn under the body, functionally analogous to suction-feeding fishes. Skates also rotate the rostrum upwards although with the open rostral sides and the smaller fin area weaker fluid flow is generated. However, skates also use a rostral strike behavior in which the rostrum is rapidly rotated downwards pushing fluid towards the substrate to potentially stun or uncover prey. Thus, both species use the anterior portion of the body to direct fluid flow to handle prey albeit in different ways, which may be explained by differences in morphology. Rostral stiffness and pectoral fin insertion onto the rostrum differ between skates and rays and this corresponds to behavioral differences in prey handling resulting in distinct fluid flow patterns. The flexible muscular rostrum and greater fin area of stingrays allow more extensive use of suction to handle prey while the stiff cartilaginous rostrum of skates lacking extensive fin insertion is used as a paddle to strike prey as well as to clear away sand cover. Copyright © 2011 Elsevier GmbH. All rights reserved.

Handle with Care! Mid-Atlantic Marine Animals That Demand Your Respect. Educational Series No. 26. Third Printing.

Science.gov (United States)

Lucy, Jon

Generally speaking, marine organisms found along middle Atlantic shores are not considered threatening to people. However, some of these animals can cause problems, either upon simple contact with the skin, as in the case of some jellyfish, or through careless handling. In addition, larger inhabitants of coastal waters (such as sharks) must always…

Development of constrained motion control for robot handling of hazardous waste

International Nuclear Information System (INIS)

Starr, G.P.

1993-01-01

Handling and archiving of hazardous waste is an area where automation and robotics can be of significant benefit, by removing the human operator from the workplace and its associated hazards. For reasons of safety, throughput, and reduced setup time, force-controlled robots are well-suited for hazardous materials handling. The focus of this investigation is the development of advanced force control techniques for commercial industrial robots in the surface sampling of hazardous waste containers. Two particular control strategies are considered, (1) preview control, and (2) adaptive control. Preview control uses a sensor which can ''look ahead'' and thereby reduce the effect of surface irregularity on contact force control. Adaptive control allows the robot controller to compensate for changes in the robot characteristics as it changes position, and likewise improves performance. The resulting control algorithms will be applied to a two-dimensional contour-following task using a PUMA robot at the Robotics Research Laboratory at The University of New Mexico. (author) 9 figs., 13 refs

The impact of spent fuel reprocessing facilities deployment rate on transuranics inventory in alternative fuel cycle strategies

International Nuclear Information System (INIS)

Aquien, A.; Kazimi, M.; Hejzlar, P.

2007-01-01

The depletion rate of transuranic inventories from spent fuel depends on both the deployment of advanced reactors that can be loaded with recycled transuranics, and on the deployment of the facilities that separate and reprocess spent fuel. In addition to tracking the mass allocation of TRU in the system and calculating a system cost, the fuel cycle simulation tool CAFCA includes a flexible recycling plant deployment model. This study analyses the impact of different recycling deployment schemes for various fuel cycle strategies in the US over the next hundred years under the assumption of a demand for nuclear energy growing at a rate of 2,4%. Recycling strategies explored in this study fall under two categories: recycling in thermal light water reactors using combined non-fertile and UO 2 fuel (CONFU) and recycling in fast reactors (either fertile-free actinide burner reactors, or self-sustaining gas-cooled fast reactors). Preliminary results show that the earlier deployment of recycling in the thermal reactors will limit the stored levels of TRU below those of fast reactors. However, the avoided accumulation of spent fuel interim storage depends on the deployment rate of the recycling facilities. In addition, by the end of the mid century, the TRU in cooling storage will exceed that in interim storage. (authors)

Evaluation of a self-guided transport vehicle for remote transportation of transuranic and other hazardous waste

Energy Technology Data Exchange (ETDEWEB)

Rice, P.M.; Moody, S.J.; Peterson, R. [and others

1997-04-01

Between 1952 and 1970, over two million cubic ft of transuranic mixed waste was buried in shallow pits and trenches in the Subsurface Disposal Area at the Idaho National Engineering Laboratory`s Radioactive Waste Management Complex. Commingled with this two million cubic ft of waste is up to 10 million cubic ft of fill soil. The pits and trenches were constructed similarly to municipal landfills with both stacked and random dump waste forms such as barrels and boxes. The main contaminants are micron-sized particles of plutonium and americium oxides, chlorides, and hydroxides. Retrieval, treatment, and disposal is one of the options being considered for the waste. This report describes the results of a field demonstration conducted to evaluate a technology for transporting exhumed transuranic wastes at the Idaho National Engineering and Environmental Laboratory (INEEL) and at other hazardous or radioactive waste sites through the U.S. Department of Energy complex. The full-scale demonstration, conducted at the INEEL Robotics Center in the summer of 1995, evaluated equipment performance and techniques for remote transport of exhumed buried waste. The technology consisted of a Self-Guided Transport Vehicle designed to remotely convey retrieved waste from the retrieval digface and transport it to a receiving/processing area with minimal human intervention. Data were gathered and analyzed to evaluate performance parameters such as precision and accuracy of navigation and transportation rates.

Evaluation of a self-guided transport vehicle for remote transportation of transuranic and other hazardous waste

International Nuclear Information System (INIS)

Rice, P.M.; Moody, S.J.; Peterson, R.

1997-04-01

Between 1952 and 1970, over two million cubic ft of transuranic mixed waste was buried in shallow pits and trenches in the Subsurface Disposal Area at the Idaho National Engineering Laboratory's Radioactive Waste Management Complex. Commingled with this two million cubic ft of waste is up to 10 million cubic ft of fill soil. The pits and trenches were constructed similarly to municipal landfills with both stacked and random dump waste forms such as barrels and boxes. The main contaminants are micron-sized particles of plutonium and americium oxides, chlorides, and hydroxides. Retrieval, treatment, and disposal is one of the options being considered for the waste. This report describes the results of a field demonstration conducted to evaluate a technology for transporting exhumed transuranic wastes at the Idaho National Engineering and Environmental Laboratory (INEEL) and at other hazardous or radioactive waste sites through the U.S. Department of Energy complex. The full-scale demonstration, conducted at the INEEL Robotics Center in the summer of 1995, evaluated equipment performance and techniques for remote transport of exhumed buried waste. The technology consisted of a Self-Guided Transport Vehicle designed to remotely convey retrieved waste from the retrieval digface and transport it to a receiving/processing area with minimal human intervention. Data were gathered and analyzed to evaluate performance parameters such as precision and accuracy of navigation and transportation rates