WorldWideScience

Sample records for constant barium strontium

  1. Investigation of thickness effects on the dielectric constant barium strontium titanate thin films

    CERN Document Server

    Grattan, L J

    2002-01-01

    The collapse in dielectric constant at small thickness commonly observed in ferroelectric thin films was measured and investigated in barium strontium titanate (Ba sub 0 sub . sub 5 Sr sub 0 sub . sub 5 TiO sub 3). The possible mechanisms responsible for this effect are reviewed. Functional measurements were performed on BST thin films, of 7.5 to 950 nm, by incorporating them into capacitor structures with bottom electrodes of strontium ruthenate (SRO) and thermally- evaporated Au top electrodes. A discussion on thin film growth considerations, optimal PLD conditions and the measurement techniques employed in the project is presented. The experimentally determined dielectric constant - thickness profile was fitted using the series capacitor model assuming low dielectric constant interfacial layers in series with the bulk. Consideration of the case where the combined 'dead layer' thickness was close to the total BST thickness revealed that, for this system, the total 'dead layer' thickness had to be less than ...

  2. Effect of Change in Ba Concentration on Crystallintiy and Dielectric Constant of the Sol-Gel Deposited Barium Strontium Titante (BST Films on n-Type Si Wafer

    Directory of Open Access Journals (Sweden)

    C.C. Tripathi

    2011-01-01

    Full Text Available Thin (Bax, Sr1 – xTiO3 (BST films of different chemical compositions (x = 0.3 0.5 & 0.7 were prepared by the sol-gel process using barium acetate, strontium acetate and titanium isopropoxide as metal alkoxides. The titanium isopropoxide was dissolved in acetyl acetone (chelating agent and mixing the resultant solution with barium and strontium acetate dissolved in acetic acid solution. The alkoxide group in titanium isopropoxide was replaced by acetate ligand and after hydrolysis and condensation process a complex solution was obtained. This solution was deposited on n-type (111 Si wafers by spin coating and after drying at 350 ºC the samples were annealed at 700 ºC in oxygen ambient. The precise control of composition of different species is important for producing good quality films having high crystallinity and dielectric constant. The crystallinity of the film was found to increase with the increase of Ba concentration as found from X-ray diffraction. The calculated value of dielectric constant from CV measurements revealed that the film of (Ba0.7, Sr0.3 TiO3 had the maximum dielectric constant as 463 and the surface was examined by SEM.

  3. Printed Barium Strontium Titanate capacitors on silicon

    Energy Technology Data Exchange (ETDEWEB)

    Sette, Daniele [Univ. Grenoble Alpes, F-38000 Grenoble (France); CEA, LETI, MINATEC Campus, F-38054 Grenoble (France); Luxembourg Institute of Science and Technology LIST, Materials Research and Technology Department, L-4422 Belvaux (Luxembourg); Kovacova, Veronika [Univ. Grenoble Alpes, F-38000 Grenoble (France); CEA, LETI, MINATEC Campus, F-38054 Grenoble (France); Defay, Emmanuel, E-mail: emmanuel.defay@list.lu [Univ. Grenoble Alpes, F-38000 Grenoble (France); CEA, LETI, MINATEC Campus, F-38054 Grenoble (France); Luxembourg Institute of Science and Technology LIST, Materials Research and Technology Department, L-4422 Belvaux (Luxembourg)

    2015-08-31

    In this paper, we show that Barium Strontium Titanate (BST) films can be prepared by inkjet printing of sol–gel precursors on platinized silicon substrate. Moreover, a functional variable capacitor working in the GHz range has been made without any lithography or etching steps. Finally, this technology requires 40 times less precursors than the standard sol–gel spin-coating technique. - Highlights: • Inkjet printing of Barium Strontium Titanate films • Deposition on silicon substrate • Inkjet printed silver top electrode • First ever BST films thinner than 1 μm RF functional variable capacitor that has required no lithography.

  4. 40 CFR 721.10011 - Barium calcium manganese strontium oxide.

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Barium calcium manganese strontium... Specific Chemical Substances § 721.10011 Barium calcium manganese strontium oxide. (a) Chemical substance... manganese strontium oxide (PMN P-00-1124; CAS No. 359427-90-0) is subject to reporting under this...

  5. Lanthanide doped strontium-barium cesium halide scintillators

    Science.gov (United States)

    Bizarri, Gregory; Bourret-Courchesne, Edith; Derenzo, Stephen E.; Borade, Ramesh B.; Gundiah, Gautam; Yan, Zewu; Hanrahan, Stephen M.; Chaudhry, Anurag; Canning, Andrew

    2015-06-09

    The present invention provides for a composition comprising an inorganic scintillator comprising an optionally lanthanide-doped strontium-barium, optionally cesium, halide, useful for detecting nuclear material.

  6. Thermal expansion behaviour of barium and strontium zirconium phosphates

    Indian Academy of Sciences (India)

    P Srikari Tantri; K Geetha; A M Umarji; Sheela K Ramasesha

    2000-12-01

    Ba1.5–SrZr4P5SiO24 compounds with = 0, 0.25, 0.5, 0.75, 1.0, 1.25 and 1.5, belonging to the low thermal expansion NZP family were synthesized by the solid state reaction method. The XRD pattern could be completely indexed with respect to R$\\bar{3}$ space group indicating the ordering of vacancy at the divalent cation octahedral sites. The microstructure and bulk thermal expansion coefficient from room temperature to 800°C of the sintered samples have been studied. All the samples show very low coefficient of thermal expansion (CTE), with = 0 samples showing negative expansion. A small substitution of strontium in the pure barium compound changes the sign of CTE. Similarly, = 1.5 sample (pure strontium) shows a positive CTE and a small substitution of barium changes its sign. = 1.0 and 1.25 samples have almost constant CTE over the entire temperature range. The low thermal expansion of these samples can be attributed to the ordering of the ions in the crystal structure of these materials.

  7. Heavy ion recoil spectrometry of barium strontium titanate films

    Science.gov (United States)

    Stannard, W. B.; Johnston, P. N.; Walker, S. R.; Bubb, I. F.; Scott, J. F.; Cohen, D. D.; Dytlewski, N.; Martin, J. W.

    1995-05-01

    Thin films of barium strontium titanate have been analysed using heavy ion recoil spectrometry with 77 and 98 MeV 127I ions at the new heavy ion recoil facility at ANSTO, Lucas Heights. New calibration procedures have been developed for quantitative analysis. Energy spectra for each of the elements present reveal interdiffusion that was not previously known.

  8. Complex Impedance Studies of Optically Excited Strontium Barium Niobate

    Science.gov (United States)

    2007-11-02

    has a tetragonal tungsten - bronze structure. The unit cell for this structure, illustrated below in Fig. 2.1, consists of ten oxygen octahedra joined...4 Kittel, pp. 373-374. 5 P. B. Jamieson, et al, “Ferroelectric Tungsten Bronze -Type Crystal Structures. I. Barium Strontium Niobate...Oxford, 1987). 2. C. Kittel, Introduction to Solid State Physics, (Wiley, New York, 1986). 3. P. B. Jamieson, et al, “Ferroelectric Tungsten

  9. Microwave-hydrothermal synthesis of barium strontium titanate nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Simoes, A.Z., E-mail: alezipo@yahoo.co [Universidade Federal de Itajuba- Unifei - Campus Itabira, Rua Sao Paulo, 377, Bairro, Amazonas, CEP 35900-37, Itabira, MG (Brazil); Universidade Estadual Paulista- Unesp - Faculdade de Engenharia de Guaratingueta, Av. Dr. Ariberto Pereira da Cunha, 333, Bairro Pedregulho, CEP 12516-410 Guaratingueta, SP (Brazil); Moura, F.; Onofre, T.B. [Universidade Federal de Itajuba- Unifei - Campus Itabira, Rua Sao Paulo, 377, Bairro, Amazonas, CEP 35900-37, Itabira, MG (Brazil); Ramirez, M.A.; Varela, J.A.; Longo, E. [Laboratorio Interdisciplinar em Ceramica (LIEC), Departamento de Fisico-Quimica, Instituto de Quimica, UNESP, CEP 14800-900, Araraquara, SP (Brazil)

    2010-10-22

    Research highlights: {yields} Barium strontium titanate nanoparticles were obtained by the Hydrothemal microwave technique (HTMW) {yields} This is a genuine technique to obtain nanoparticles at low temperature and short times {yields} Barium strontium titanate free of carbonates with tetragonal structure was grown at 130 {sup o}C. - Abstract: Hydrothermal-microwave method (HTMW) was used to synthesize crystalline barium strontium titanate (Ba{sub 0.8}Sr{sub 0.2}TiO{sub 3}) nanoparticles (BST) in the temperature range of 100-130 {sup o}C. The crystallization of BST with tetragonal structure was reached at all the synthesis temperatures along with the formation of BaCO{sub 3} as a minor impurity at lower syntheses temperatures. Typical FT-IR spectra for tetragonal (BST) nanoparticles presented well defined bands, indicating a substantial short-range order in the system. TG-DTA analyses confirmed the presence of lattice OH- groups, commonly found in materials obtained by HTMW process. FE/SEM revealed that lower syntheses temperatures led to a morphology that consisted of uniform grains while higher syntheses temperature consisted of big grains isolated and embedded in a matrix of small grains. TEM has shown BST nanoparticles with diameters between 40 and 80 nm. These results show that the HTMW synthesis route is rapid, cost effective, and could serve as an alternative to obtain BST nanoparticles.

  10. Synthesis and characterization of highly-ordered barium-strontium titanate nanotube arrays fabricated by sol-gel method

    Institute of Scientific and Technical Information of China (English)

    Chen Yu; Chen Wei; Guo Feng; Li Mei-Ya; Liu Wei; Zhao Xing-Zhong

    2009-01-01

    Highly uniformed barium-strontium titanate nanotube arrays were fabricated using a porous anodic aluminum oxide template from a barium-strontium titanate sol-gel solution. Electron microscope results showed that nanotubes with uniform length and diameter were obtained. The diameters and lengths of these nanotubes were dependent on the pore diameter and the thickness of the applied anodic aluminum oxide template. High resolution transmission electron microscopy and the selected-area electron diffraction pattern investigations demonstrated the perovskite structure and the polycrystaltine of the fabricated barium-strontium titanate nanotubes. The characterization of the electrical and dielectric properties had also been made. Compared to thin film material,the intrinsic leakage current density is almost the same. Besides,at 30 ℃,the dielectric constant and dielectric loss of the fabricated nanotube is 80 and 0.027 at 1 MHz respectively.

  11. Obtaining of Nanostructured Powders of Barium and Strontium Hexaferrite by the Polymer Precursor Method

    Directory of Open Access Journals (Sweden)

    V.G. Kostishyn

    2015-12-01

    Full Text Available Studied the possibility of obtaining by precursors in the polymer nanostructured powders of barium hexaferrite BaFe12O19 and strontium hexaferrite SrFe12O19. The reagents were used as starting barium nitrate, strontium nitrate and ferric nitrate nonahydrate (III, and polyethylene glycol-400 used this technology as a polymer.

  12. Calcium, Strontium and Barium Homogeneous Catalysts for Fine Chemicals Synthesis.

    Science.gov (United States)

    Sarazin, Yann; Carpentier, Jean-François

    2016-12-01

    The large alkaline earths (Ae), calcium, strontium and barium, have in the past 15 years yielded a brand new generation of heteroleptic molecular catalysts for the production of fine chemicals. However, the integrity of these complexes is often plagued by ligand redistribution equilibria in solution. This personal account retraces the paths followed in our research group towards the design of stable heteroleptic alkalino-earth complexes, including the use of intramolecular noncovalent Ae···H-Si and Ae···F-C interactions. Their implementation as homogenous precatalysts for reactions such as the intramolecular and intermolecular hydroamination and hydrophosphination of activated alkenes, the hydrophosphonylation of ketones, and the dehydrogenative coupling of amines and hydrosilanes that enable the efficient and controlled formations of CP, CN, or SiN σ-bonds, is presented in a synthetic perspective that highlights their overall outstanding catalytic performance.

  13. Ionoluminescence of trivalent rare-earth-doped strontium barium niobate

    Energy Technology Data Exchange (ETDEWEB)

    Calvo del Castillo, H. [Departamento de Geologia y Geoquimica, Universidad Autonoma de Madrid, Modulo C-VI, Campus de Cantoblanco, 28049 Cantoblanco, Madrid (Spain); Universidad Nacional Automoma de Mexico, Instituto de Fisica, 04510 Ciudad Universitaria, Mexico D.F. (Mexico); Ruvalcaba, J.L. [Universidad Nacional Automoma de Mexico, Instituto de Fisica, 04510 Ciudad Universitaria, Mexico D.F. (Mexico); Bettinelli, M.; Speghini, A. [Dipartimento Scientifico e Tecnologico, Universita di Verona and INSTM, UdR Verona, Ca Vignal, Strada Le Grazie 15, I-37134 Verona (Italy); Barboza Flores, M. [Centro de Investigacion en Fisica, Universidad de Sonora, Hermosillo, Sonora (Mexico); Calderon, T. [Departamento de Geologia y Geoquimica, Universidad Autonoma de Madrid, Modulo C-VI, Campus de Cantoblanco, 28049 Cantoblanco, Madrid (Spain)], E-mail: tomas.calderon@uam.es; Jaque, D.; Garcia Sole, J. [Departamento de Fisica de Materiales, Universidad Autonoma de Madrid, 28049 Cantoblanco, Madrid (Spain)

    2008-05-15

    Ionoluminescence spectra for different rare-earth ion (Pr{sup 3+} and Eu{sup 3+})-activated Sr{sub x}Ba{sub 1-x}Nb{sub 2}O{sub 6} strontium barium niobate crystals (x=0.33 and 0.60) have been induced with a 3 MeV proton beam for a variety of beam current intensities (45, 40 and 20 nA). The proton-beam induced luminescent spectra have shown features associated with the presence of the rare-earth ion and some spectral features mostly related to the host crystal, which appear only for high beam current intensities. We have compared the ionoluminescence results to those obtained under UV light excitation (photoluminescence technique) where a direct excitation of the band gap would occur.

  14. A new type of microphone using flexoelectric barium strontium titnate

    Science.gov (United States)

    Kwon, Seol ryung; Huang, Wenbin; Zhang, Shujun; Yuan, Fuh-Gwo; Jiang, Xiaoning

    2014-03-01

    A flexoelectric bridge-structured microphone using bulk barium strontium titanate (Ba0.65Sr0.35TiO3 or BST) ceramic was investigated in this study. The flexoelectric microphone was installed in an anechoic box and exposed to the sound pressure emitted from a loud speaker. Charge sensitivity of the flexoelectric microphone was measured and calibrated using a reference microphone. The 1.5 mm×768 μm×50 μm micro-machined bridge-structured flexoelectric microphone has a sensitivity of 0.92 pC/Pa, while its resonance frequency was calculated to be 98.67 kHz. The analytical and experimental results show that the flexoelectric microphone has both high sensitivity and broad bandwidth, indicating that flexoelectric microphones are potential candidates for many applications.

  15. Electronic structure of barium strontium titanate by soft-x-ray absorption spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Uehara, Y. [Mitsubishi Electric Co., Hyogo (Japan); Underwood, J.H.; Gullikson, E.M.; Perera, R.C.C. [Ernest Orlando Lawrence Berkeley National Lab., CA (United States)

    1997-04-01

    Perovskite-type titanates, such as Strontium Titanate (STO), Barium Titanate (BTO), and Lead Titanate (PTO) have been widely studied because they show good electric and optical properties. In recent years, thin films of Barium Strontium Titanate (BST) have been paid much attention as dielectrics of dynamic random access memory (DRAM) capacitors. BST is a better insulator with a higher dielectric constant than STO and can be controlled in a paraelectric phase with an appropriate ratio of Ba/Sr composition, however, few studies have been done on the electronic structure of the material. Studies of the electronic structure of such materials can be beneficial, both for fundamental physics research and for improving technological applications. BTO is a famous ferroelectric material with a tetragonal structure, in which Ti and Ba atoms are slightly displaced from the lattice points. On the other hand, BST keeps a paraelectric phase, which means that the atoms are still at the cubic lattice points. It should be of great interest to see how this difference of the local structure around Ti atoms between BTO and BST effects the electronic structure of these two materials. In this report, the authors present the Ti L{sub 2,3} absorption spectra of STO, BTO, and BST measured with very high accuracy in energy of the absorption features.

  16. NLTE Strontium and Barium in metal poor red giant stars

    CERN Document Server

    Short, C I

    2006-01-01

    We present atmospheric models of red giant stars of various metallicities, including extremely metal poor (XMP, [Fe/H]<-3.5) models, with many chemical species, including, significantly, the first two ionization stages of Strontium (Sr) and Barium (Ba), treated in Non-Local Thermodynamic Equilibrium (NLTE) with various degrees of realism. We conclude that 1) for all lines that are useful Sr and Ba abundance diagnostics the magnitude and sense of the computed NLTE effect on the predicted line strength is metallicity dependent, 2) the indirect NLTE effect of overlap between Ba and Sr transitions and transitions of other species that are also treated in NLTE non-negligibly enhances NLTE abundance corrections for some lines, 3) the indirect NLTE effect of NLTE opacity of other species on the equilibrium structure of the atmospheric model is not significant, 4) the computed NLTE line strengths differ negligibly if collisional b-b and b-f rates are an order of magnitude smaller or larger than those calculated wi...

  17. Fabrication of barium/strontium carbonate coated amorphous carbon nanotubes as an improved field emitter

    Science.gov (United States)

    Maity, S.; Jha, A.; Das, N. S.; Chattopadhyay, K. K.

    2013-02-01

    Amorphous carbon nanotubes (aCNTs) were synthesized by a chemical reaction between ferrocene and ammonium chloride at a temperature ˜250 ∘C in an air furnace. As-synthesized aCNTs were coated with the barium/strontium carbonate through a simple chemical process. The coating of barium/strontium carbonate was confirmed by a high resolution transmission electron microscopy, X-ray diffraction, and Fourier transformed infrared spectroscopy. Morphology of the as-prepared samples was studied by field emission scanning electron microscopy. Thermal gravimetric analysis showed that barium/strontium carbonate coated aCNTs are more stable than the pristine aCNTs. As-prepared barium/strontium carbonate coated aCNTs showed significantly improved field emission properties with a turn-on field as low as 2.5 V/μm. The variation of field emission characteristics of the barium/strontium carbonate coated aCNTs with interelectrode distances was also studied.

  18. Characterizations of strontium(II) and barium(II) adsorption from aqueous solutions using dolomite powder.

    Science.gov (United States)

    Ghaemi, Ahad; Torab-Mostaedi, Meisam; Ghannadi-Maragheh, Mohammad

    2011-06-15

    In this research, adsorption technique was applied for strontium and barium removal from aqueous solution using dolomite powder. The process has been investigated as a function of pH, contact time, temperature and adsorbate concentration. The experimental data was analyzed using equilibrium isotherm, kinetic and thermodynamic models. The isotherm data was well described by Langmuir isotherm model. The maximum adsorption capacity was found to be 1.172 and 3.958 mg/g for Sr(II) and Ba(II) from the Langmuir isotherm model at 293 K, respectively. The kinetic data was tested using first and pseudo-second order models. The results indicated that adsorption fitted well with the pseudo-second order kinetic model. The thermodynamic parameters (ΔG°, ΔH°, and ΔS°) were also determined using the equilibrium constant value obtained at different temperatures. The results showed that the adsorption for both ions was feasible and exothermic.

  19. Synthesis and characterization of nickel oxide doped barium strontium titanate ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Banerjee, M. [Dept. of Electrical Engineering, Bengal Institute of Technology Kolkata (India); Mukherjee, S. [Dept. of Metallurgical Engineering, Jadavpur University, Kolkata (India); Maitra, S. [Govt. College of Engg. and Ceramic Technology, Kolkata (India)

    2012-01-15

    Barium strontium titanate (BST) ceramics (Ba{sub 0.6}Sr{sub 0.4})TiO{sub 3} were synthesized by solid state sintering using barium carbonate, strontium carbonate and rutile as the precursor materials. The samples were doped with nickel oxide in different proportions. Different phases present in the sintered samples were determined from X-ray diffraction investigation and the distribution of different phases in the microstructure was assessed from scanning electron microscopy study. It was observed that the dielectric properties of BST were modified significantly with nickel oxide doping. These ceramics held promise for applications in tuned circuits. (author)

  20. Structural and luminescent studies on nanosized cerium doped strontium barium niobate

    Science.gov (United States)

    John, Nuja; Nandakumar, K.

    2017-06-01

    The nanosized cerium doped Strontium Barium Niobate ceramic powder system have been synthesized by sol-gel technique. The X-ray diffraction measurement confirmed the structure of cerium doped Strontium Barium Niobate ceramic powder system. The absorption peaks were analysed by FTIR spectroscopy. Particle morphology and size of the powder were examined using SEM and TEM. Crystal quality and structure were also examined by micro raman spectra. The transmission electron microscopy image of cerium doped Strontium Barium Niobate nano powder system consist of particles with average size of 20 nm. A band gap of the system was measured by optical absorption spectra. Photoluminescence data were recorded at room temperature. The emission peaks were detected under excitation at 305 nm wavelength. The peaks are assigned to the cerium electron transition from lowest 5d level to 2F5/2 and 2F7/2 of 4f, respectively. The decay time were also measured for cerium doped Strontium Barium Niobate powder system.

  1. Use of barium-strontium carbonatite for flux welding and surfacing of mining machines

    Science.gov (United States)

    Kryukov, R. E.; Kozyrev, N. A.; Usoltsev, A. A.

    2017-09-01

    The results of application of barium-strontium carbonatite for modifying and refining iron-carbon alloys, used for welding and surfacing in ore mining and smelting industry, are generalized. The technology of manufacturing a flux additive containing 70 % of barium-strontium carbonatite and 30 % of liquid glass is proposed. Several compositions of welding fluxes based on silicomanganese slag were tested. The flux additive was introduced in an amount of 1, 3, 5 %. Technological features of welding with the application of the examined fluxes are determined. X-ray spectral analysis of the chemical composition of examined fluxes, slag crusts and weld metal was carried out, as well as metallographic investigations of welded joints. The principal possibility of applying barium-strontium carbonatite as a refining and gas-protective additive for welding fluxes is shown. The use of barium-strontium carbonatite reduces the contamination of the weld seam with nonmetallic inclusions: non-deforming silicates, spot oxides and brittle silicates, and increases the desulfurizing capacity of welding fluxes.

  2. Electromagnetic wave absorbing characteristics of synthetized barium strontium titanate/polyaniline nanocomposites

    Science.gov (United States)

    Mulyani, O.; Hafizah, M. A. E.; Manaf, A.

    2017-07-01

    In this paper, electromagnetic wave absorbing characteristics of electrically conductive composites consisted of polyaniline (PANi) and nanoparticles of barium strontium titanate (BST) is described. The BST nanoparticles were synthesized by the mechanical alloying method and successive particle size reduction steps through high frequency ultrasonic irradiation treatments. Whereas polyaniline was produced by oxidative polymerization processes which allows efficient control of the dielectric properties. Mechanical alloying combined with ultrasonic irradiation treatments has resulted in BST powders with a mean particle size of a few nanometers (less than 100 nm). Such ultra-fine particles of BST were then used to synthesize the BST/PANi nanocomposites with 20:80, 50:50 and 80:20 compositions. The physical properties like particle sizes, dielectric constant, electromagnetic absorption characteristics are investigated by X-Ray Diffractometer, Fourier Transform Infrared, and Vector Network Analyzer. It was found that BST/polyaniline nanocomposite can enhance main properties of the electromagnetic absorber. The high dielectric constant of BST and conductivity of polyaniline support nanocomposite BST/polyaniline as electromagnetic absorber materials.

  3. Microstructural and Electrical Characterization of Barium Strontium Titanate-Based Solid Solution Thin Films Deposited on Ceramic Substrates by Pulsed Laser Deposition

    Science.gov (United States)

    2003-04-03

    Strontium Titanate-Based Solid Solution Thin Films Deposited on Ceramic Substrates by Pulsed Laser Deposition DISTRIBUTION: Approved for public...Society H2.4 Microstructural and Electrical Characterization of Barium Strontium Titanate- based Solid Solution Thin Films Deposited on Ceramic...investigated and report the microstructural and electrical characterization of selected barium strontium titanate-based solid solution thin films

  4. Synthesis and characterization of strontium and barium guanidinate; Synthese und Charakterisierung von Strontium- und Bariumguanidinat

    Energy Technology Data Exchange (ETDEWEB)

    Missong, Ronja

    2016-07-01

    After investigation of the mono-alkali-metal guanidinates in recent years and the structural properties of the various compounds by means of X-ray and neutron diffraction, the guanidinates of the alkaline earth metals seemed to be well investigated. The synthesis of the mono-alkali-metal guanidinates in liquid ammonia has been further developed for the alkaline earth metal guanidinates. Strontium guanidinate was used for the first time to synthesize a compound with a twofold deprotonated guanidinate anion and to study the structure of this compound by means of spectroscopic analysis and different diffraction methods. The structure model was generated from X-ray powder diffraction data, supplemented by density function theory with the help of hydrogen position and subsequently refined and validated with highly resolved neutron diffraction data. The anion has the predicted C3h symmetry and thus resembles the appearance of a Trinacria. The compound of the barium guanidinate with the desired composition Ba (CN3H4) 2 was also investigated by means of IR spectroscopy and different diffraction methods. Structural proposals were developed from X-ray and flight time neutron diffraction data. However, the results of the refinements of these proposals were not satisfactory. In some structure-chemical aspects, however, the individual structural proposals nevertheless produced a uniform picture. The close relationship between the various structural proposals suggests that a final structure could be in many respects consistent with the various structural proposals. [German] Nachdem die Monoalkaliguanidinate in den letzten Jahren untersucht wurden und die strukturellen Eigenschaften der verschiedenen Verbindungen mittels Roentgen- und Neutronenbeugung aufgeklaert werden konnten, schien es aussichtsreich auch die Guanidinate der Erdalkalimetalle zu untersuchen. Die Synthese der Monoalkaliguanidinate in fluessigem Ammoniak wurde fuer die Erdalkalimetallguanidinate weiter entwickelt

  5. Correlated Strontium and Barium Isotopic Compositions of Acid-Cleaned Single Silicon Carbides from Murchison

    CERN Document Server

    Liu, Nan; Gallino, Roberto; Davis, Andrew M; Bisterzo, Sara; Gyngard, Frank; Kaeppeler, Franz; Cristallo, Sergio; Dauphas, Nicolas; Pellin, Michael J; Dillmann, Iris

    2015-01-01

    We present strontium, barium, carbon, and silicon isotopic compositions of 61 acid-cleaned presolar SiC grains from Murchison. Comparison with previous data shows that acid washing is highly effective in removing both strontium and barium contamination. For the first time, by using correlated $^{88}Sr$/$^{86}Sr$ and $^{138}Ba$/$^{136}Ba$ ratios in mainstream SiC grains, we are able to resolve the effect of $^{13}C$ concentration from that of $^{13}C$-pocket mass on s-process nucleosynthesis, which points towards the existence of large $^{13}C$-pockets with low $^{13}C$ concentration in AGB stars. The presence of such large $^{13}$R-pockets with a variety of relatively low $^{13}C$ concentrations seems to require multiple mixing processes in parent AGB stars of mainstream SiC grains.

  6. CORRELATED STRONTIUM AND BARIUM ISOTOPIC COMPOSITIONS OF ACID-CLEANED SINGLE MAINSTREAM SILICON CARBIDES FROM MURCHISON

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Nan; Savina, Michael R.; Gallino, Roberto; Davis, Andrew M.; Bisterzo, Sara; Gyngard, Frank; Käppeler, Franz; Cristallo, Sergio; Dauphas, Nicolas; Pellin, Michael J.; Dillmann, Iris

    2015-04-08

    We present strontium, barium, carbon, and silicon isotopic compositions of 61 acid-cleaned presolar SiC grains from Murchison. Comparison with previous data shows that acid washing is highly effective in removing both strontium and barium contamination. For the first time, by using correlated Sr-88/Sr-86 and Ba-138/Ba-136 ratios in mainstream SiC grains, we are able to resolve the effect of C-13 concentration from that of C-13-pocket mass on s-process nucleosynthesis, which points toward the existence of large C-13 pockets with low C-13 concentrations in asymptotic giant branch stars. The presence of such large C-13 pockets with a variety of relatively low C-13 concentrations seems to require multiple mixing processes in parent asymptotic giant branch stars of mainstream SiC grains.

  7. CORRELATED STRONTIUM AND BARIUM ISOTOPIC COMPOSITIONS OF ACID-CLEANED SINGLE MAINSTREAM SILICON CARBIDES FROM MURCHISON

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Nan; Davis, Andrew M.; Dauphas, Nicolas; Pellin, Michael J. [Department of the Geophysical Sciences, The University of Chicago, Chicago, IL, 60637 (United States); Savina, Michael R. [Chicago Center for Cosmochemistry, Chicago, IL 60637 (United States); Gallino, Roberto; Bisterzo, Sara [Dipartimento di Fisica, Università di Torino, I-10125 Torino (Italy); Gyngard, Frank [Laboratory for Space Sciences, Washington University, St. Louis, MO 63130 (United States); Käppeler, Franz [Karlsruhe Institute of Technology, Institut für Kernphysik, Karlsruhe D-76021 (Germany); Cristallo, Sergio [INAF, Osservatorio Astronomico di Collurania, I-64100 Teramo (Italy); Dillmann, Iris, E-mail: lnsmile@uchicago.edu [TRIUMF, 4004 Wesbrook Mall, Vancouver BC V6T 2A3 (Canada)

    2015-04-10

    We present strontium, barium, carbon, and silicon isotopic compositions of 61 acid-cleaned presolar SiC grains from Murchison. Comparison with previous data shows that acid washing is highly effective in removing both strontium and barium contamination. For the first time, by using correlated {sup 88}Sr/{sup 86}Sr and {sup 138}Ba/{sup 136}Ba ratios in mainstream SiC grains, we are able to resolve the effect of {sup 13}C concentration from that of {sup 13}C-pocket mass on s-process nucleosynthesis, which points toward the existence of large {sup 13}C pockets with low {sup 13}C concentrations in asymptotic giant branch stars. The presence of such large {sup 13}C pockets with a variety of relatively low {sup 13}C concentrations seems to require multiple mixing processes in parent asymptotic giant branch stars of mainstream SiC grains.

  8. Photorefractive properties of ion-implanted waveguides in strontium barium niobate crystals

    Science.gov (United States)

    Kip, D.; Kemper, B.; Nee, I.; Pankrath, R.; Moretti, P.

    1997-10-01

    Planar optical waveguides were formed in cerium-doped strontium barium niobate single crystals (Sr0.61Ba0.39Nb2O6, SBN61), either by proton or helium ion implantation. Proton-implanted samples show a large increase of dark conductivity that reduces or even prevents the recording of refractive index gratings. For waveguides formed by helium implantation this effect is absent, and they can be used for efficient holographic recording. Photorefractive properties of the waveguides are investigated by two-beam coupling. After implantation with 2.0 MeV He+ and doses of (0.5-5)񺔗 cm-2, the samples have to be polarized again, because heating or charge effects at the crystals surface during the implantation process decreases or even reverses the effective electrooptic coefficients in the waveguiding layer. For repoled samples, we find logarithmic gain coefficients of up to 45 cm-1 with time constants for the build-up of the purely ?/2-shifted refractive index grating of the order of 1 ms for the blue lines of an Ar+ laser. Photoconductivity depends nonlinearly on light intensity with an exponent xƸ.55. With increasing implanted helium dose, both electronic and nuclear damage of the waveguiding layer grows, and the photorefractive properties of the waveguides are considerably degraded.

  9. Growth and characterization of barium strontium titanate thin films by metal-organic decomposition

    Science.gov (United States)

    Jana, Pradeep

    Barium Strontium Titanate (Basb1-xSrsbxTiOsb3) - BST, has been identified to be an important material for application in charge storage (capacitors and DRAM) because of its high dielectric constant and low leakage current. Metal Organic Decomposition (MOD) is a simple process for the growth of thin films with fast processing, ease of deposition and low investment. Individual organometallic precursors are first mixed together in required stoichiometric ratios to obtain a solution that is deposited on the substrate. It is then heated to pyrolyze the organic solvents. Multiple layers are deposited to achieve the required thickness and a final anneal is performed for crystallization. The present study involves the deposition of thin films of BST (x = 0.35) from acetate precursors on platinized silicon substrates by MOD spin-on process and characterization for their phase, composition, morphological and electrical properties with the aid of XRD, EDS, WDS, SEM, AFM and electronic instrumentation, as functions of thickness, temperature and frequency. The growth parameters are optimized and are correlated to the physical and electrical properties.

  10. A Study on Reactive Ion Etching of Barium Strontium Titanate Films Using Mixtures of Argon (Ar), Carbon Tetrafluoride (CF4), and Sulfur Hexafluoride (SF6)

    Science.gov (United States)

    2014-07-01

    A Study on Reactive Ion Etching of Barium Strontium Titanate Films Using Mixtures of Argon (Ar), Carbon Tetrafluoride (CF4), and Sulfur...Etching of Barium Strontium Titanate Films Using Mixtures of Argon (Ar), Carbon Tetrafluoride (CF4), and Sulfur Hexafluoride (SF6) Samuel G...Study on Reactive Ion Etching of Barium Strontium Titanate Films Using Mixtures of Argon (Ar), Carbon Tetrafluoride (CF4), and Sulfur Hexafluoride

  11. Modification of gray iron produced by induction melting with barium strontium

    Science.gov (United States)

    Modzelevskaya, G.; Feoktistov, A. V.; Selyanin, I. F.; Kutsenko, A. I.; Kutsenko, A. A.

    2016-09-01

    The article provides analysis of results of gray iron experimental melts in induction furnace and the following melt modification with barium-strontium carbonate (BSC-2). It is shown that modification positively affects mechanical and casting properties and as-cast iron structure. It was established that BSC-2 granulated immediately prior to use has greater impact on melt than BSC-2 of the same faction, supplied by the manufacturer.

  12. Anion and cation diffusion in barium titanate and strontium titanate; Anionen- und Kationendiffusion in Barium- und Strontiumtitanat

    Energy Technology Data Exchange (ETDEWEB)

    Kessel, Markus Franz

    2012-12-19

    Perovskite oxides show various interesting properties providing several technical applications. In many cases the defect chemistry is the key to understand and influence the material's properties. In this work the defect chemistry of barium titanate and strontium titanate is analysed by anion and cation diffusion experiments and subsequent time-of-flight secondary ion mass spectrometry (ToF-SIMS). The reoxidation equation for barium titanate used in multi-layer ceramic capacitors (MLCCs) is found out by a combination of different isotope exchange experiments and the analysis of the resulting tracer diffusion profiles. It is shown that the incorporation of oxygen from water vapour is faster by orders of magnitude than from molecular oxygen. Chemical analysis shows the samples contain various dopants leading to a complex defect chemistry. Dysprosium is the most important dopant, acting partially as a donor and partially as an acceptor in this effectively acceptor-doped material. TEM and EELS analysis show the inhomogeneous distribution of Dy in a core-shell microstructure. The oxygen partial pressure and temperature dependence of the oxygen tracer diffusion coefficients is analysed and explained by the complex defect chemistry of Dy-doped barium titanate. Additional fast diffusion profiles are attributed to fast diffusion along grain boundaries. In addition to the barium titanate ceramics from an important technical application, oxygen diffusion in cubic, nominally undoped BaTiO{sub 3} single crystals has been studied by means of {sup 18}O{sub 2}/{sup 16}O{sub 2} isotope exchange annealing and subsequent determination of the isotope profiles in the solid by ToF-SIMS. It is shown that a correct description of the diffusion profiles requires the analysis of the diffusion through the surface space-charge into the material's bulk. Surface exchange coefficients, space-charge potentials and bulk diffusion coefficients are analysed as a function of oxygen partial

  13. Structural, topographical and electrical properties of cerium doped strontium barium niobate (Ce:SBN60) ceramics

    Science.gov (United States)

    Raj, S. Gokul; Mathivanan, V.; Kumar, G. Ramesh; Yathavan, S.; Mohan, R.

    2016-05-01

    Tungsten bronze type cerium doped strontium barium niobate (Ce:SBN - Sr0.6B0.4Nb2O6) ceramics were synthesized by solid state process. Cerium was used as dopant to improve its electrical properties. Influence of Ce+ ions on the photoluminescence properties was investigated in detail. The grain size topographical behavior of SBN powders and their associated abnormal grain growth (AGG) were completely analyzed through SEM studies. Finally dielectric, measurement discusses about the broad phase transition observed due to cerium dopant The results were discussed in detail.

  14. Low temperature preparation of nanocrystalline solid solution of strontium barium niobate by chemical process

    Indian Academy of Sciences (India)

    Asit B Panda; Amita Pathak; Panchanan Pramanik

    2002-11-01

    SrBa1–Nb2O6 (with = 0.4, 0.5 and 0.6) powders have been prepared by thermolysis of aqueous precursor solutions consisting of triethanolamine (TEA), niobium tartarate and, EDTA complexes of strontium and barium ions. Complete evaporation of the precursor solution by heating at ∼ 200°C, yields in a fluffy, mesoporous carbon rich precursor material, which on calcination at 750°C/2 h has resulted in the pure SBN powders. The crystallite and average particle sizes are found to be around 15 nm and 20 nm, respectively.

  15. Direct writing of ferroelectric domains on strontium barium niobate crystals using focused ultraviolet laser light

    Energy Technology Data Exchange (ETDEWEB)

    Boes, Andreas; Crasto, Tristan; Steigerwald, Hendrik; Mitchell, Arnan [School of Electrical and Computer Engineering and ARC Center for Ultra-High Bandwidth Devices for Optical Systems (CUDOS), RMIT University, Melbourne, Victoria 3001 (Australia); Wade, Scott [Faculty of Engineering and Industrial Sciences, Swinburne University of Technology, Hawthorn, Victoria 3122 (Australia); Frohnhaus, Jakob; Soergel, Elisabeth [Institute of Physics, University of Bonn, Wegelerstr. 8, 53115 Bonn (Germany)

    2013-09-30

    We report ferroelectric domain inversion in strontium barium niobate (SBN) single crystals by irradiating the surface locally with a strongly focused ultraviolet (UV) laser beam. The generated domains are investigated using piezoresponse force microscopy. We propose a simple model that allows predicting the domain width as a function of the irradiation intensity, which indeed applies for both SBN and LiNbO{sub 3}. Evidently, though fundamentally different, the domain structure of both SBN and LiNbO{sub 3} can be engineered through similar UV irradiation.

  16. Structural, topographical and electrical properties of cerium doped strontium barium niobate (Ce:SBN60) ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Raj, S. Gokul [Department of Physics, C. Kandaswami Naidu College For Men (CKNC), Annanagar, Chennai-600102 (India); Mathivanan, V.; Mohan, R. [Department of Physics, Presidency College, Chennai – 600005 (India); Kumar, G. Ramesh, E-mail: rameshvandhai@gmail.com; Yathavan, S. [Department of Physics, University College of Engineering Arni, Anna University Chennai, Arni-632317 (India)

    2016-05-06

    Tungsten bronze type cerium doped strontium barium niobate (Ce:SBN - Sr{sub 0.6}B{sub 0.4}Nb{sub 2}O{sub 6}) ceramics were synthesized by solid state process. Cerium was used as dopant to improve its electrical properties. Influence of Ce{sup +} ions on the photoluminescence properties was investigated in detail. The grain size topographical behavior of SBN powders and their associated abnormal grain growth (AGG) were completely analyzed through SEM studies. Finally dielectric, measurement discusses about the broad phase transition observed due to cerium dopant The results were discussed in detail.

  17. Solid state (47,49)Ti, (87)Sr and (137)Ba NMR characterisation of mixed barium/strontium titanate perovskites.

    Science.gov (United States)

    Gervais, Christel; Veautier, Delphine; Smith, Mark E; Babonneau, Florence; Belleville, Philippe; Sanchez, Clément

    2004-01-01

    Solid state (47,49)Ti, (137)Ba, (87)Sr NMR spectra have been recorded on BaxSrl-xTiO3 (0 strontium) in the coordination second sphere of the probed titanium site: substitution of strontium by barium induces the broadening of the peaks, due to quadrupolar effects, while the isotropic chemical shift increases. (137)Ba NMR spectra exhibit a distribution of the quadrupolar interaction, that could be tentatively quantified, CQ increasing with the amount of strontium. Preliminary results were also obtained on (87)Sr NMR showing behaviour comparable to (137)Ba NMR, i.e. a broadening of the peaks due to an increasing quadrupolar interaction with the amount of barium distorting the environment of the strontium sites.

  18. Structural and thermal studies of modified silica-strontium-barium glass from CRT

    Science.gov (United States)

    Grelowska, I.; Kosmal, M.; Reben, M.; Pichniarczyk, P.; Sitarz, M.; Olejniczak, Z.

    2016-12-01

    Glasses were prepared by conventional melting method from 100 g batches. The influence of alumina and calcium oxide on the crystallization process of silica-strontium-barium glass from Cathode Ray Tube (CRT) were studied by means of 27Al MAS NMR and FTIR spectroscopy. This made possible to determine the influence of additives, e.g. blast furnace slag and cement dust on the structural changes of glasses (changes in the spectra shapes). The introduction of waste modifiers into the glass structure leads to the breaking of Al-O-Si and Si-O-Si bonds what causes the depolymerization of the glass network. From the FTIR spectra the narrowing of the bands at 1022 and 1027 cm-1 was observed, which may indicate on the ordering of glass network. Appearance of alumina in coordination 4 was confirmed by NMR investigations. The effects of compositional variation, thermal treatment on the nature, type and stability field of crystallizing phases and microstructure formed in CaO and/or Al2O3 silica-strontium-barium glasses were described using DTA/DSC method. Thermal characteristics of glasses like the transition temperature Tg, the temperature for the crystallization Tc, thermal stability parameter were determined. The crystalline phase was determined by the X-ray diffractometry. The microstructure of the samples was studied by SEM technique. Analysis of the local atomic interactions in the structure of glasses has been used to explain the course of the crystallization.

  19. Dielectric properties of barium strontium titanate / non ferroelectric oxide ceramic composites

    Energy Technology Data Exchange (ETDEWEB)

    Nenez, S. [THALES, Domaine de Corbeville, Orsay (France); Univ. de Bourgogne, Lab. de Recherche sur la Reactivite des Solides, Dijon (France); Morell, A.; Pate, M.; Ganne, J.P. [THALES, Domaine de Corbeville, Orsay (France); Maglione, M. [Inst. de Chimie de la Matiere Condensee de Bordeaux - CNRS, Pessac (France); Niepce, J.C. [Univ. de Bourgogne, Lab. de Recherche sur la Reactivite des Solides, Dijon (France)

    2002-07-01

    Barium strontium titanate ceramics present high dielectric permittivity and tunability. In order to reduce their permittivity and loss tangent while keeping tunability, various composites of barium strontium titanate oxide Ba{sub 0.6}Sr{sub 0.4}TiO{sub 3} combined with non-ferroelectric oxides such as magnesium titanate MgTiO{sub 3} or magnesia MgO were investigated. The Ba-Sr oxide powder was mixed with 20, 40 or 60 wt% of the non-ferroelectric oxide (NFO). The paper discusses the processing and the material characterisations by X-ray diffraction and SEM. A secondary phase BaMg{sub 6}Ti{sub 6}O{sub 19} was detected only in the composites synthesised with MgTiO{sub 3}. The microstructure and the dielectric characteristics are presented and discussed. A correlation between the microstructure of the composites, including secondary phase and the dielectric properties is proposed. (orig.)

  20. Removal efficiency of water purifier and adsorbent for iodine, cesium, strontium, barium and zirconium in drinking water.

    Science.gov (United States)

    Sato, Itaru; Kudo, Hiroaki; Tsuda, Shuji

    2011-01-01

    The severe incident of Fukushima Daiichi Nuclear Power Station has caused radioactive contamination of environment including drinking water. Radioactive iodine, cesium, strontium, barium and zirconium are hazardous fission products because of the high yield and/or relatively long half-life. In the present study, 4 pot-type water purifiers and several adsorbents were examined for the removal effects on these elements from drinking water. Iodide, iodate, cesium and barium were removed by all water purifiers with efficiencies about 85%, 40%, 75-90% and higher than 85%, respectively. These efficiencies lasted for 200 l, which is near the recommended limits for use of filter cartridges, without decay. Strontium was removed with initial efficiencies from 70% to 100%, but the efficiencies were slightly decreased by use. Zirconium was removed by two models, but hardly removed by the other models. Synthetic zeolite A4 efficiently removed cesium, strontium and barium, but had no effect on iodine and zirconium. Natural zeolite, mordenite, removed cesium with an efficiency as high as zeolite A4, but the removal efficiencies for strontium and barium were far less than those of zeolite A4. Activated carbon had little removal effects on these elements. In case of radioactive contamination of tap water, water purifiers may be available for convenient decontamination of drinking water in the home.

  1. Dielectric relaxation of barium strontium titanate and application to thin films for DRAM capacitors

    Science.gov (United States)

    Baniecki, John David

    This thesis examines the issues associated with incorporating the high dielectric constant material Barium Strontium Titanate (BSTO) in to the storage capacitor of a dynamic random access memory (DRAM). The research is focused on two areas: characterizing and understanding the factors that control charge retention in BSTO thin films and modifying the electrical properties using ion implantation. The dielectric relaxation of BSTO thin films deposited by metal-organic chemical vapor deposition (MOCVD) is investigated in the time and frequency domains. It is shown that the frequency dispersion of the complex capacitance of BSTO thin films can be understood in terms of a power-law frequency dependence from 1mHz to 20GHz. From the correspondence between the time and frequency domain measurements, it is concluded that the power-law relaxation currents extend back to the nano second regime of DRAM operation. The temperature, field, and annealing dependence of the dielectric relaxation currents are also investigated and mechanisms for the observed power law relaxation are explored. An equivalent circuit model of a high dielectric constant thin film capacitor is developed based on the electrical measurements and implemented in PSPICE. Excellent agreement is found between the experimental and simulated electrical characteristics showing the utility of the equivalent circuit model in simulating the electrical properties of high dielectric constant thin films. Using the equivalent circuit model, it is shown that the greatest charge loss due to dielectric relaxation occurs during the first read after a refresh time following a write to the opposite logic state for a capacitor that has been written to the same logic state for a long time (opposite state write charge loss). A theoretical closed form expression that is a function of three material parameters is developed which estimates the opposite state write charge loss due to dielectric relaxation. Using the closed form

  2. Verification of the flexoelectricity in barium strontium titanate through d33 meter

    Science.gov (United States)

    Shu, Longlong; Wang, Tong; Jiang, Xiaoning; Huang, Wenbin

    2016-12-01

    Flexoelectricity is a newly arising electromechanical property that couples strain gradient to polarization. This physical property widely exists in most of the solid dielectrics but has quite weak response that often overlooked. Recently, barium strontium titanate (BST), a well-known ferroelectrics, has been reported to be a promising flexoelectric material, and thus triggered the associated studies on flexoelectricity to a new height. However, part of the researchers argued the observed flexoelectricity in BST is either by residual piezoelectricity or centric symmetry breaking during the densification process. In this paper, we would verify the flexoelectricity in BST ceramics by many comparison experiments. Our experimental result suggested the observed polarization in BST material is likely to be induced by strain gradient through flexoelectricity.

  3. Effective removal of methyl blue by fine-structured strontium and barium phosphate nanorods

    Science.gov (United States)

    Zhang, Fan; Song, Weijie; Lan, Jing

    2015-01-01

    In this work, the composite of strontium phosphate and barium phosphate (called SBP) nanorods have been synthesized, characterized and studied for removal of methyl blue (MB). The effects of pH, temperature, contact time, initial dye concentration on removal of MB were studied in detail. Results suggest that pH and temperature were not critical limiting factors for the removal of MB. Reaching equilibrium was very rapid (within 10 min) and the high adsorption capacity of MB by SBP nanorods was 1691.8 mg/g at initial dye concentration of 2000 mg/L. The adsorption process obeyed the pseudo-second-order kinetics model and Langmuir isotherm model. Importantly, the mechanism contributed to the MB removal was proposed to be the ionic interaction and hydrogen bonds for low dye concentration, chemical precipitation for high dye concentration. It is predicted that the SBP nanorods being an effective adsorbent for elimination of MB from colored aqueous solutions.

  4. Barium Strontium Titanate Thin Film Growth with rotational speed variation as a satellite temperature sensor prototype

    Science.gov (United States)

    Mulyadi; Rika, W.; Sulidah; Irzaman; Hardhienata, Hendradi

    2017-01-01

    Barium Strontium Titanate(BST) is a promising material for sensor devices such as temperature and infrared sensor. BaxSr1-xTiO3 thin films with affordable Si substrate were prepared by chemical solution deposition method and spin coating technique for 30 seconds with variation in rotation speed (3000 rpm, 5500 rpm and 8000 rpm). A high baking temperature at 8500C has been used for 15 hours during the annealing process. The thickness of BST film was calculated via gravimetric calculation. USB 2000 VIS-NIR was used to characterize the optical properties of BST thin film. The obtained reflectance curve showed that the most reflected wavelengths were in the range of 408-452 nm respectively. The result of the optical film characterization is very important for further development as a sensor in satellite technology.

  5. Study of a Flexible Low Profile Tunable Dipole Antenna Using Barium Strontium Titanate Varactors

    Science.gov (United States)

    Cure, David; Weller, Thomas; Miranda, Felix A.

    2014-01-01

    In this paper a flexible low profile dipole antenna using a frequency selective surface (FSS) with interdigital barium strontium titanate (BST) varactor-tuned unit cells is presented. The varactor chips were placed only along one dimension of the FSS to avoid the use of vias and simplify the DC bias network. The antenna uses overlapping metallic plates that resemble fish scales as a ground plane to improve the flexibility of the multi-material stack structure. The measured data of the antenna demonstrate tunability from 2.42 GHz to 2.66 GHz and 1.3 dB gain drop when using overlapping metallic plates instead of continuous ground plane. The total antenna thickness is approximately lambda/24.

  6. Verification of the flexoelectricity in barium strontium titanate through d33 meter

    Directory of Open Access Journals (Sweden)

    Longlong Shu

    2016-12-01

    Full Text Available Flexoelectricity is a newly arising electromechanical property that couples strain gradient to polarization. This physical property widely exists in most of the solid dielectrics but has quite weak response that often overlooked. Recently, barium strontium titanate (BST, a well-known ferroelectrics, has been reported to be a promising flexoelectric material, and thus triggered the associated studies on flexoelectricity to a new height. However, part of the researchers argued the observed flexoelectricity in BST is either by residual piezoelectricity or centric symmetry breaking during the densification process. In this paper, we would verify the flexoelectricity in BST ceramics by many comparison experiments. Our experimental result suggested the observed polarization in BST material is likely to be induced by strain gradient through flexoelectricity.

  7. Studies on gas sensing performance of pure and modified barium strontium titanate thick film resistors

    Indian Academy of Sciences (India)

    G H Jain; L A Patil; P P Patil; U P Mulik; K R Patil

    2007-02-01

    Barium strontium titanate ((Ba0.87Sr0.13)TiO3–BST) ceramic powder was prepared by mechanochemical process. The thick films of different thicknesses of BST were prepared by screen-printing technique and gas-sensing performance of these films was tested for various gases. The films showed highest response and selectivity to ammonia gas. The effect of film thickness on gas response was also studied. As prepared BST thick films were surface modified by dipping them into an aqueous solution of titanium chloride (TiCl3) for different intervals of time. Surface modification shifted response to H2S gas suppressing the responses to ammonia and other gases. The surface modification, using dipping process, altered the adsorbate–adsorbent interactions, which gave the unusual sensitivity and selectivity effect. Sensitivity, selectivity, thermal stability, response and recovery time of the sensor were measured and presented.

  8. Multi-parameter sensing using high-k oxide of barium strontium titanate

    Energy Technology Data Exchange (ETDEWEB)

    Huck, Christina; Poghossian, Arshak; Baecker, Matthias; Schoening, Michael J. [Institute of Nano- and Biotechnologies (INB), FH Aachen, 52428, Juelich (Germany); Peter Gruenberg Institute (PGI-8), Forschungszentrum Juelich GmbH, 52525, Juelich (Germany); Reisert, Steffen; Kramer, Friederike [Institute of Nano- and Biotechnologies (INB), FH Aachen, 52428, Juelich (Germany); Begoyan, Vardges K.; Buniatyan, Vahe V. [Department of Microelectronics and Biomedical Devices, State Engineering University of Armenia, 0009, Yerevan (Armenia)

    2015-06-15

    High-k perovskite oxide of barium strontium titanate (BST) represents a very attractive multi-functional transducer material for the development of (bio-)chemical sensors. In this work, a Si-based sensor chip containing Pt interdigitated electrodes covered with a thin BST layer (485 nm) has been developed for multi-parameter chemical sensing. The chip has been applied for the contactless measurement of the electrolyte conductivity, the detection of adsorbed charged macromolecules (positively charged polyelectrolytes of polyethylenimine) and the concentration of hydrogen peroxide (H{sub 2}O{sub 2}) vapor. The experimental results of functional testing of individual sensors are presented. The mechanism of the BST sensitivity to charged polyelectrolytes and H{sub 2}O{sub 2} vapor has been proposed and discussed. (copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  9. Growth and characterization of barium tantalate-based microwave ceramics and barium and strontium titanate ferroelectrics

    Science.gov (United States)

    Liu, Shaojun

    In this thesis, we explore the growth and properties of electronic ceramics used in microwave resonator and energy storage. Their applications require high dielectric constants, which do not vary significantly with temperature and loss dissipation loss. Single-phase Ba(Cd1/3 Ta2/3)O3 powder is produced using conventional solid state reaction methods. Ab-initio electronic structure calculations show that the covalent nature of the directional d-electron bonding in these high-Z oxides plays an important role in producing a more rigid lattice with higher melting points and enhanced phonon energies and consequently resulting materials with a high dielectric constant and a low microwave loss for Ba(Cd1/3Ta2/3) O3 and Ba(Zn1/3 Ta2/3)O3 ceramics. Ba(Cd1/3Ta 2/3)O3 samples with high sintering density and excellent microwave properties are made with boron oxide as sintering aid at 1200--1350°C, corresponding to temperatures 300°C lower than samples prepared without a sintering aid. XRD combined with High Resolution Electron Microscopy (HREM) indicates that Ba( Cd1/3Ta2/3)O 3 ceramics prepared with boron oxide have a well-ordered hexagonal structure. Transmission Electron Microscope (TEM) results indicate that the improvement in densification contributes to the liquid sintering mechanism for boron concentrations exceeding 0.5wt%. Annealing treatment and high boron concentrations are also found to improve the microwave properties. For example, Ba( Cd1/3Ta2/3)O 3 doped with 0.5,vt%o B2O 3 ceramics annealed at 1250°C for 40 hours has a dielectric constant (epsilonr) and temperature coefficient of resonant frequency (tauf) of 32 and 80 +/- 15 ppm/°C respectively and a loss tangent (Q) of loss tangent (< 1.7 x 10-5) at 2 GHz was achieved using a high temperature 1680°C and 48h sintering process. Doping Sc into Ba0.7 Sr0.3TiO3 ceramics changes its crystal structure from tetragonal to rhombohedral structure and significantly reduces the dielectric constant, of Ba0.7 Sr0.3TiO3

  10. The effect of the host composition on the lifetime decay properties of barium/strontium aluminates compounds

    Energy Technology Data Exchange (ETDEWEB)

    Rezende, Marcos V. dos S., E-mail: mvsrezende@gmail.com [Departamento de Física, Universidade Federal de Sergipe, 49500-000 Itabaiana, SE (Brazil); Andrade, A. B.; Valerio, Mário E. G. [Departamento de Física, Universidade Federal de Sergipe, 49100-000 São Cristóvão, SE (Brazil); Montes, Paulo J. R [Instituto Federal de Sergipe, 49400-000 Lagarto, SE (Brazil)

    2014-03-14

    This paper reports the influence of the structural change on the luminescence of Eu-doped barium/strontium aluminates when excited with monochromatic X-rays (also known as X-ray excited optical luminescence—XEOL). Ba{sub 1−x}Sr{sub x}Al{sub 2}O{sub 4} samples, with 0 < x < 1, were produced via proteic sol-gel route and it was observed that the XEOL emission spectra are composed by the Eu{sup 2+} and Eu{sup 3+} transitions, although no Eu{sup 2+} was observed in the X-ray absorption spectra. The XEOL intensities while the sample is under irradiation decreased as a function of the irradiation time, indicating the buildup of radiation damage. The saturation level of the XEOL is directly correlated to the amount of damages induced by the irradiation and the sample composition. The Ba-rich samples are the ones with higher XEOL yield. X-ray induced long lasting phosphorescence (LLP) was also observed for all samples and it was found that the duration of the phosphorescence emission also depends on the sample composition. In Sr-rich samples, the LLP has a slower decay time constant than in Ba-rich samples. A model of the radiation induced luminescence is presented and all these features are discussed in terms of the energetic costs and the type of defects generated in the sample.

  11. Effect of Homogeniety on Microstructure, Dielectric, and FerroelectricProperties of Strontium Barium Niobate

    Directory of Open Access Journals (Sweden)

    P.K. Patro

    2007-01-01

    Full Text Available Strontium barium niobate (SBN is tetragonal tungsten bronze structured ferroelectric material.It is one of the few lead-free ferroelectrics in the fore-front of environment-friendly electroceramicresearch and development. The unusual sintering behaviour of SBN exhibits abnormal graingrowth, duplex microstructure, and low density that has plagued commercial exploitation of SBN.The formation of duplex microstructure becomes more prominent when synthesised byconventional solid-state approach. Compositional inhomogeneity is believed to be the key playerof such ambiguity. Will homogeneous mixing eliminate this problem? To answer this question,first SBN was synthesised by conventional solid-state technique, then coprecipitation technique,a wet chemical route, was employed for synthesis of SBN. In coprecipitate route, the precursorswere mixed at the molecular level. It is thought that the improved composition uniformity mighthelp in eliminating microstructure-related problems with improved dielectric properties. Thefindings in this connection on microstructure, dielectric, and ferroelectric properties of SBNwhen synthesised by conventional solid-state route as well as coprecipitation route have beendiscussed.

  12. The effect of milling time and sintering temperature on formation of nanoparticles barium strontium titanate

    Science.gov (United States)

    Yustanti, Erlina; Hafizah, Mas Ayu Elita; Manaf, Azwar

    2017-01-01

    Nanoparticles of barium strontium titanate (BST) or Ba0.3Sr0.7TiO3 were synthesized by mechanical alloying and successive ultrasonic irradiation treatment. This research attempted to reduce the particles obtained through mechanical milling of mechanically alloyed powders to the particles with sizes in nanometer scale. The effectiveness of milling time on the synthesis of BST nanoparticles was confirmed by mean particle size evaluation which showed that a milling duration up to 60 h was required to bring down gradually the mean particle from 5.7 into 2.4 µm. The broadening lines of XRD pattern of the ultrasonically treated samples were analyzed using a high score plus (HSP) and a whole powder pattern modeling (WPPM) software to obtain the crystallite size distribution. The mean crystallite size of the treated particles was found 49 nm which is about 60 times lower than its mean particle size. It is shown that mechanical alloying through the sintering process followed by ultrasonic destruction will promote the formation of nanoparticles.

  13. Effective removal of methyl blue by fine-structured strontium and barium phosphate nanorods

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Fan, E-mail: zhangfan0128@njau.edu.cn [College of Science, Nanjing Agricultural University, Nanjing 210095 (China); Song, Weijie [Ningbo Institute of Material Technology and Engineering, Chinese Academy of Sciences, Ningbo 315201 (China); Lan, Jing [College of Chemistry and Pharmaceutical Sciences, Qingdao Agricultural University, Qingdao 266109 (China)

    2015-01-30

    Graphical abstract: - Highlights: • SBP nanorods have been studied for removal of methyl blue from solutions. • The high adsorption capacity was calculated to be 1691.8 mg/g. • The equilibrium reached within 10 min and obeyed the pseudo-second-order kinetics. • The mechanism was the ionic interaction, hydrogen bonds and chemical precipitation. - Abstract: In this work, the composite of strontium phosphate and barium phosphate (called SBP) nanorods have been synthesized, characterized and studied for removal of methyl blue (MB). The effects of pH, temperature, contact time, initial dye concentration on removal of MB were studied in detail. Results suggest that pH and temperature were not critical limiting factors for the removal of MB. Reaching equilibrium was very rapid (within 10 min) and the high adsorption capacity of MB by SBP nanorods was 1691.8 mg/g at initial dye concentration of 2000 mg/L. The adsorption process obeyed the pseudo-second-order kinetics model and Langmuir isotherm model. Importantly, the mechanism contributed to the MB removal was proposed to be the ionic interaction and hydrogen bonds for low dye concentration, chemical precipitation for high dye concentration. It is predicted that the SBP nanorods being an effective adsorbent for elimination of MB from colored aqueous solutions.

  14. Synthesis of barium and strontium carbonate crystals with unusual morphologies using an organic additive

    Science.gov (United States)

    Chen, Long; Jiang, Jizhong; Bao, Zuben; Pan, Jian; Xu, Weibing; Zhou, Lili; Wu, Zhigang; Chen, Xu

    2013-12-01

    In this paper, strontium carbonate (SrCO3) and barium carbonate (BaCO3) crystals were synthesized in the presence of an organic additive-hexamethylenetetramine (HMT) using two CO2 sources. Scanning electron microscopy and X-ray powder diffractometry were used to characterize the products. The results showed that the morphologies of orthorhombic strontianite SrCO3 transformed from branch-like to flower-like, and to capsicum-like at last, while the morphologies of BaCO3 change from fiber-like to branchlike, and to rod-like finally with an increase of the molar ratio HMT/Sr2+ and HMT/Ba2+ from 0.2 to 10 using ammonium carbonate as CO2 source. When using diethyl carbonate instead of ammonium carbonate as CO2 source, SrCO3 flowers aggregated by rods and BaCO3 shuttles were formed. The possible formation mechanisms of SrCO3 and BaCO3 crystals obtained in different conditions were also discussed.

  15. Localized devitrifiation in Er{sup 3+}-doped strontium barium niobate glass by laser irradiation

    Energy Technology Data Exchange (ETDEWEB)

    Haro-Gonzalez, P.; Martin, I.R.; Lahoz, F.; Gonzalez-Perez, S. [Universidad de La Laguna, Departamento de Fisica Fundamental, Electronica y Sistemas, La Laguna, Tenerife (Spain); Capuj, N.E. [Universidad de La Laguna, Departamento de Fisica Basica, La Laguna, Tenerife (Spain); Jaque, D. [Universidad Autonoma de Madrid, Departamento de Fisica de Materiales, Madrid (Spain)

    2008-12-15

    Localized devitrifiation in strontium barium niobate glass doped with Er{sup 3+} under laser irradiation has been carried out. The samples of this study have been fabricated by the melt quenching method and doped with 5% mol of Er{sup 3+}. A 1.5-W cw Ar laser was focused on the sample to obtain devitrifiation of the glass. Evidence of the changes induced by the Ar laser has been observed through the analysis of the photoluminescence of the Er{sup 3+} ions. The transitions corresponding to {sup 2}H{sub 11/2}{yields}{sup 4}I{sub 15/2}, {sup 4}S{sub 3/2}{yields}{sup 4}I{sub 15/2} and {sup 4}F{sub 9/2}{yields}{sup 4}I{sub 15/2} have been studied to analyze structure changes. Microluminescence measurements have been carried out to spatially select positions inside and outside the irradiated area. We have observed changes in the emission bands corresponding to these transitions. The emission bands from Er{sup 3+} ions in the irradiated zone show a resolved structure while they are broadened outside that area. These changes in the optical properties of the Er{sup 3+} ions indicate that the Ar-laser irradiation has produced a change in the local structure of the material. These results show that a localized devitrifiation has been produced after the laser action and the transition from glass to glass ceramic has been completed. (orig.)

  16. Comparision of Uptake Models for Strontium (Sr) and Barium (Ba) in Vine (Vitis vinifera L.) in Castilla-La Mancha (spain).

    Science.gov (United States)

    Amorós, José Angel; Pérez-de-los-Reyes, Caridad; García-Navarro, Francisco J.; Bravo, Sandra; Higueras, Pablo; Moreno, Marta

    2015-04-01

    Castilla-La Mancha is the biggest vine-growing region in the world (about 500,000 ha) and one of the most important in terms of production of wine. The soils diversity should induce differences in the uptake of mineral elements by the vineyard. Of over the regional vine extension, 101 plots were selected and analyzed soil samples from each of them, following the description by FAO procedures. Samples of leaves were also taken from each soil plot. We analyzed the contents of mineral elements in both soil and leaf, using the FRX technique. This paper is focused on the elements strontium and barium because they are the trace elements having a higher concentration in the soils of the region, with values in soil range from 22.3 mg•kg-1-3602.7 mg•kg-1 in strontium and from 65.4 mg•kg-1 to 469.3 mg•kg-1 in barium. The contents of both elements in leaves have ranged from 23.3 mg•kg-1 y 1084.5 mg•kg-1 for strontium, and between 3.86 mg•kg-1 and 235.0 mg•kg-1 for barium. The aim of this work is state the behaviour in the soil-plant system for both elements. For this study, different statistical adjustment models have been tested (linear, multiplicative, exponential and logarithmic). The results show that the values of "R" for strontium are higher than barium in all models. Samples have also been studied by soil order (classified according to the FAO criteria). In this case, significant correlation from strontium have been found in all soil orders, except in calcisols. Significant correlations for barium appear only in entisols and luvisols. In conclusion it can be seen how these two elements differ in their behaviour in the soil-plant system. In general, the concentration of strontium in the soil is better correlated with leaf content than barium in the same soil. We can suggest a greater facility for the absorption of strontium by the grapevine. In calcisols, bearing in mind the interference of calcium, this uptake does not present such a high correlation

  17. Barium iodide and strontium iodide crystals andd scintillators implementing the same

    Science.gov (United States)

    Payne, Stephen A; Cherepy, Nerine J; Hull, Giulia E; Drobshoff, Alexander D; Burger, Arnold

    2013-11-12

    In one embodiment, a material comprises a crystal comprising strontium iodide providing at least 50,000 photons per MeV. A scintillator radiation detector according to another embodiment includes a scintillator optic comprising europium-doped strontium iodide providing at least 50,000 photons per MeV. A scintillator radiation detector in yet another embodiment includes a scintillator optic comprising SrI.sub.2 and BaI.sub.2, wherein a ratio of SrI.sub.2 to BaI.sub.2 is in a range of between 0:1 A method for manufacturing a crystal suitable for use in a scintillator includes mixing strontium iodide-containing crystals with a source of Eu.sup.2+, heating the mixture above a melting point of the strontium iodide-containing crystals, and cooling the heated mixture near the seed crystal for growing a crystal. Additional materials, systems, and methods are presented.

  18. Brillouin light scattering study of transverse mode coupling in confined yttrium iron garnet/barium strontium titanate multiferroic

    Energy Technology Data Exchange (ETDEWEB)

    Sadovnikov, A. V., E-mail: sadovnikovav@gmail.com; Nikitov, S. A. [Laboratory “Metamaterials,” Saratov State University, Saratov 410012 (Russian Federation); Kotel' nikov Institute of Radioengineering and Electronics, Russian Academy of Sciences, Moscow 125009 (Russian Federation); Beginin, E. N.; Bublikov, K. V.; Grishin, S. V.; Sheshukova, S. E.; Sharaevskii, Yu. P. [Laboratory “Metamaterials,” Saratov State University, Saratov 410012 (Russian Federation)

    2015-11-28

    Using the space-resolved Brillouin light scattering spectroscopy we study the transformation of dynamic magnetization patterns in a bilayer multiferroic structure. We show that in the comparison with a single yttrium iron garnet (YIG) film magnetization distribution is transformed in the bilayer structure due to the coupling of waves propagating both in an YIG film (magnetic layer) and in a barium strontium titanate slab (ferroelectric layer). We present a simple electrodynamic model using the numerical finite element method to show the transformation of eigenmode spectrum of confined multiferroic. In particular, we demonstrate that the control over the dynamic magnetization and the transformation of spatial profiles of transverse modes in magnetic film of the bilayer structure can be performed by the tuning of the wavevectors of transverse modes. The studied confined multiferroic stripe can be utilized for fabrication of integrated dual tunable functional devices for magnonic applications.

  19. Influence of sintering temperature on microstructures and energy-storage properties of barium strontium titanate glass-ceramics prepared by sol-gel process

    Energy Technology Data Exchange (ETDEWEB)

    Zhu, Jia; Zhang, Yong; Song, Xiaozhen; Zhang, Qian; Yang, Dongliang; Chen, Yongzhou [Beijing Key Laboratory of Fine Ceramics, State Key Laboratory of New Ceramics and Fine Processing, Institute of Nuclear and New Energy Technology, Tsinghua University, Beijing, 100084 (China)

    2015-12-15

    The sol-gel processing, microstructures, dielectric properties and energy-storage properties of barium strontium titanate glass-ceramics over the sintering temperature range of 1000-1150 C were studied. Through the X-ray diffraction result, it is revealed that the crystallinity increases as the sintering temperature increased from 1000 to 1080 C and has reached a steady-state regime above 1100 C. Scanning electron microscopy images showed that with the increase of sintering temperature, the crystal size increased. Dielectric measurements revealed that the increase in the sintering temperature resulted in a significant increase in the dielectric constant, a strong sharpness of the temperature-dependent dielectric response and a pronounced decrease of the temperature of the dielectric maximum. The correlation between charge spreading behavior and activation energies of crystal and glass was discussed by the employment of the impedance spectroscopy studies. As a result of polarization-electric field hysteresis loops, both the charged and discharged densities increased with increasing sintering temperature. And the maximum value of energy storage efficiency was found to occur at 1130 C. Finally, the dependence of released energy and power densities calculated from the discharged current-time (I-t) curves on the sintering temperature was studied. The relationship between the energy storage properties and microstructure was correlated. Polarization-electric field hysteresis loops for the BST glass-ceramics sintered at different temperatures. (copyright 2015 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  20. The Structure, Dielectric and Energy Storage Properties of Strontium Barium Niobate-Based Glass-Ceramics Doped with La2O3

    Science.gov (United States)

    Xiu, Shaomei; Xiao, Shi; Shen, Bo; Zhai, Jiwei

    2017-07-01

    In this work, the effect of La2O3 content on the phase evolution, microstructure, dielectric properties and energy storage properties of the strontium barium niobate (SBN)-based glass-ceramics were studied. The results show that the La3+ is easily incorporated into the tetragonal tungsten bronze structured phase, and La2O3 doped into the BSN-glass-ceramics, as a grain growth inhibitor, can have an evident effect on the grain size reduction and crystallization. The microstructure of the SBN-glass-ceramics becomes denser and more uniform with increasing La2O3 content. The remanent polarization of all samples is extremely low. The dielectric constant of the SBN-glass-ceramics obviously is decreased, while the breakdown strength is increased with the increment of La2O3 content. When La2O3 content in the SBN-glass-ceramics is 0.2 mol.%, the theoretical energy storage density is at the maximal level of 7.2 J/cm3. In addition, the energy discharging efficiency and discharging speed of the SBN-glass-ceramics with different La2O3 content were evaluated. With La2O3 content increasing, the energy discharging efficiency gradually increased.

  1. Structural Properties of Nonstoichiometric Barium and Strontium Peroxides: BaO 2- x (1.97≥2- x≥1.72) and SrO 2- x (1.98≥2- x≥1.90)

    Science.gov (United States)

    Königstein, Markus

    1999-11-01

    The crystal structures of eight single crystals of barium and strontium peroxide, prepared by high pressure-high temperature synthesis, were determined by X-ray diffraction. The crystallographic data were successfully refined in the calcium carbide structure (space group I4/mmm, Z=2). The results clearly indicate that the peroxides are nonstoichiometric compounds, MO2-x (M=Ba, Sr), with a peroxide deficiency and that oxide ions are present on interstitial lattice sites. The composition rage extends from near stoichiometry to compounds with a total oxygen content of 1.72 in the barium and 1.90 in the strontium peroxide. We find that the oxide ions, replacing the peroxide molecular ions, occupy an interstitial position that is in the middle of the replaced peroxide molecular ion. A decrease of the peroxide content in the crystals results in a decreased c-axis of the tetragonal unit cell of the structure, while the a-axis is almost constant. Furthermore, the peroxide bond length decreases, as was confirmed by Raman spectroscopy.

  2. Screening of plant species for phytoremediation of uranium, thorium, barium, nickel, strontium and lead contaminated soils from a uranium mill tailings repository in South China.

    Science.gov (United States)

    Li, Guang-yue; Hu, Nan; Ding, De-xin; Zheng, Ji-fang; Liu, Yu-long; Wang, Yong-dong; Nie, Xiao-qin

    2011-06-01

    The concentrations of uranium, thorium, barium, nickel, strontium and lead in the samples of the tailings and plant species collected from a uranium mill tailings repository in South China were analyzed. Then, the removal capability of a plant for a target element was assessed. It was found that Phragmites australis had the greatest removal capabilities for uranium (820 μg), thorium (103 μg) and lead (1,870 μg). Miscanthus floridulus had the greatest removal capabilities for barium (3,730 μg) and nickel (667 μg), and Parthenocissus quinquefolia had the greatest removal capability for strontium (3,920 μg). In this study, a novel coefficient, termed as phytoremediation factor (PF), was proposed, for the first time, to assess the potential of a plant to be used in phytoremediation of a target element contaminated soil. Phragmites australis has the highest PFs for uranium (16.6), thorium (8.68), barium (10.0) and lead (10.5). Miscanthus floridulus has the highest PF for Ni (25.0). Broussonetia papyrifera and Parthenocissus quinquefolia have the relatively high PFs for strontium (28.1 and 25.4, respectively). On the basis of the definition for a hyperaccumulator, only Cyperus iria and Parthenocissus quinquefolia satisfied the criteria for hyperaccumulator of uranium (36.4 μg/g) and strontium (190 μg/g), and could be the candidates for phytoremediation of uranium and strontium contaminated soils. The results show that the PF has advantage over the hyperaccumulator in reflecting the removal capabilities of a plant for a target element, and is more adequate for assessing the potential of a plant to be used in phytoremediation than conventional method.

  3. Barium iodide and strontium iodide crystals and scintillators implementing the same

    Energy Technology Data Exchange (ETDEWEB)

    Payne, Stephen A.; Cherepy, Nerine J.; Hull, Giulia E.; Drobshoff, Alexander D.; Burger, Arnold

    2016-11-29

    In one embodiment, a material comprises a crystal comprising strontium iodide providing at least 50,000 photons per MeV, where the strontium iodide material is characterized by a volume not less than 1 cm.sup.3. In another embodiment, a scintillator optic includes europium-doped strontium iodide providing at least 50,000 photons per MeV, where the europium in the crystal is primarily Eu.sup.2+, and the europium is present in an amount greater than about 1.6%. A scintillator radiation detector in yet another embodiment includes a scintillator optic comprising SrI.sub.2 and BaI.sub.2, where a ratio of SrI.sub.2 to BaI.sub.2 is in a range of between 0:1 and 1.0, the scintillator optic is a crystal that provides at least 50,000 scintillation photons per MeV and energy resolution of less than about 5% at 662 keV, and the crystal has a volume of 1 cm.sup.3 or more; the scintillator optic contains more than about 2% europium.

  4. Measurements of the time constant for steady ionization in shaped-charge barium releases

    Science.gov (United States)

    Hoch, Edward L.; Hallinan, Thomas J.

    1993-01-01

    Quantitative measurements of three solar illuminated shaped-charge barium releases injected at small angles to the magnetic field were made using a calibrated color television camera. Two of the releases were from 1989. The third release, a reanalysis of an event included in Hallinan's 1988 study of three 1986 releases, was included to provide continuity between the two studies. Time constants for ionization, measured during the first 25 s of each release, were found to vary considerably. The two 1989 time constants differed substantially, and both were significantly less than any of the 1986 time constants. On the basis of this variability, we conclude that the two 1989 releases showed evidence of continuous nonsolar ionization. One release showed nonsolar ionization which could not he attributed to Alfven's critical ionization velocity process, which requires a component of velocity perpendicular to the magnetic field providing a perpendicular energy greater than the ionization potential.

  5. Optical properties of Er{sup 3+}-doped strontium barium niobate nanocrystals obtained by thermal treatment in glass

    Energy Technology Data Exchange (ETDEWEB)

    Haro-Gonzalez, P. [Dep. of Fisica Fundamental Experimental, Electronica y Sistemas, Universidad de La Laguna Avda Astrofisico Franscisco Sanchez, 38206 La Laguna, S/C de Tenerife (Spain)], E-mail: patharo@ull.es; Lahoz, F. [Dep. of Fisica Fundamental Experimental, Electronica y Sistemas, Universidad de La Laguna Avda Astrofisico Franscisco Sanchez, 38206 La Laguna, S/C de Tenerife (Spain); Gonzalez-Platas, J. [Dep. of Fisica Fundamental II, Universidad de La Laguna, 38206 La Laguna, S/C de Tenerife (Spain); Caceres, J.M. [Dep. of Edafologia y Geologia, Universidad de La Laguna, 38206 La Laguna, S/C de Tenerife (Spain); Gonzalez-Perez, S. [Dep. of Fisica Fundamental Experimental, Electronica y Sistemas, Universidad de La Laguna Avda Astrofisico Franscisco Sanchez, 38206 La Laguna, S/C de Tenerife (Spain); Marrero-Lopez, D. [Dep. of Quimica Inorganica, Universidad de La Laguna, 38206 La Laguna, S/C de Tenerife (Spain); Capuj, N. [Dep. of Fisica Basica, Universidad de La Laguna, 38206 La Laguna, S/C de Tenerife (Spain); Martin, I.R. [Dep. of Fisica Fundamental Experimental, Electronica y Sistemas, Universidad de La Laguna Avda Astrofisico Franscisco Sanchez, 38206 La Laguna, S/C de Tenerife (Spain)

    2008-05-15

    Measurements of the optical properties of Er{sup 3+} ions in strontium barium niobate glass and glass ceramics have been carried out. The glasses have been fabricated using a melt-quenching method, and the glass ceramic samples have been obtained from the glass precursor by a thermal treatment. The ceramic samples formed by a glassy phase, and a crystalline phase contains nanocrystals of Sr{sub 1-x}Ba{sub x}Nb{sub 2}O{sub 6} (SBN) doped with Er{sup 3+} ions with a mean size of {approx}50 nm, as confirmed with XRD. Green up-conversion emission has been obtained under excitation at 800 nm, and the temporal evolution of this emission has been reported with the purpose of determining the involved up-conversion mechanism. These optical measures have confirmed that the Er{sup 3+} ions have been incorporated into the SBN matrix, after a thermal treatment, which produced an increment of the up-conversion efficiency.

  6. Experimental and theoretical study of molecular structure of beryllium, magnesium, calcium, strontium and barium 4-nitrobenzoates

    Science.gov (United States)

    Samsonowicz, M.; Regulska, E.; Świsłocka, R.; Lewandowski, W.

    2013-02-01

    The influence of alkaline earth metal ions on the electronic system of 4-nitrobenzoic acid was studied in this paper. The vibrational (FT-IR) and NMR (1H and 13C) spectra were recorded for 4-nitrobenzoic acid (4-nba) and its salts (4-nb). The assignment of vibrational spectra was done. Some shifts of band wavenumbers in alkaline earth metal 4-nitrobenzoates spectra were observed in the series from magnesium to barium salts. Good correlations between wavenumbers of the vibrational bands in the IR spectra of studied salts and ionic potential, electronegativity, inverse of atomic mass, ionic radius and ionization energy of studied metals were found. The regular changes in the chemical shifts of protons (1H NMR) and carbons (13C NMR) in the series of studied salts were also observed. Optimized geometrical structures of studied compounds were calculated by B3LYP method using 6-311++G** as well as LANL2DZ basis sets. Theoretical wavenumbers and intensities in IR and chemical shifts in NMR spectra were also obtained. The calculated parameters were compared with experimental data of studied compounds.

  7. Experimental and theoretical study of molecular structure of beryllium, magnesium, calcium, strontium and barium 4-nitrobenzoates.

    Science.gov (United States)

    Samsonowicz, M; Regulska, E; Świsłocka, R; Lewandowski, W

    2013-02-15

    The influence of alkaline earth metal ions on the electronic system of 4-nitrobenzoic acid was studied in this paper. The vibrational (FT-IR) and NMR ((1)H and (13)C) spectra were recorded for 4-nitrobenzoic acid (4-nba) and its salts (4-nb). The assignment of vibrational spectra was done. Some shifts of band wavenumbers in alkaline earth metal 4-nitrobenzoates spectra were observed in the series from magnesium to barium salts. Good correlations between wavenumbers of the vibrational bands in the IR spectra of studied salts and ionic potential, electronegativity, inverse of atomic mass, ionic radius and ionization energy of studied metals were found. The regular changes in the chemical shifts of protons ((1)H NMR) and carbons ((13)C NMR) in the series of studied salts were also observed. Optimized geometrical structures of studied compounds were calculated by B3LYP method using 6-311++G(**) as well as LANL2DZ basis sets. Theoretical wavenumbers and intensities in IR and chemical shifts in NMR spectra were also obtained. The calculated parameters were compared with experimental data of studied compounds.

  8. Concentrations of strontium, barium, cadmium, copper, zinc, manganese, chromium, antimony, selenium and lead in the equine liver and kidneys.

    Science.gov (United States)

    Paßlack, Nadine; Mainzer, Barbara; Lahrssen-Wiederholt, Monika; Schafft, Helmut; Palavinskas, Richard; Breithaupt, Angele; Neumann, Konrad; Zentek, Jürgen

    2014-01-01

    The concentrations of specific elements in the equine liver and kidneys are of practical relevance since horses are not only food-producing animals, but also partially serve as an indicator for the environmental pollution, as the basic feed includes plants like grass, grain and fruits. In this study, the concentrations of strontium (Sr), barium (Ba), cadmium (Cd), copper (Cu), zinc (Zn), manganese (Mn), chromium (Cr), antimony (Sb), selenium (Se) and lead (Pb) were measured in the liver, renal cortex and renal medulla of 21 horses (8 male; 13 female; aged between 5 months-28 years), using inductively coupled plasma mass spectrometry. Comparable Cu and Zn concentrations were detected in the liver and renal cortex, while approximately 50% lower concentrations were measured in the renal medulla. The lowest Sr, Cd and Se, but the highest Mn, Sb and Pb concentrations were measured in the liver. The Ba concentrations were comparable in the renal cortex and medulla, but lower in the liver of the horses. Gender-related differences were observed for Cd, Mn and Cr, with higher Cd concentrations in the liver, but lower Mn concentrations in the renal cortex and lower Cr concentrations in the renal medulla of female horses. Age-related differences were detected for most measured elements, however, the animal number per age-group was only low. In conclusion, the present study provides important reference data for the storage of Sr, Ba, Cd, Cu, Zn, Mn, Cr, Sb, Se and Pb in the liver and kidneys of horses, which are of practical relevance for an evaluation of the exposure of horses to these elements, either via feed or the environment.

  9. Experimental (FT-IR, FT-Raman, 1H NMR) and theoretical study of magnesium, calcium, strontium, and barium picolinates.

    Science.gov (United States)

    Swiderski, G; Kalinowska, M; Wojtulewski, S; Lewandowski, W

    2006-05-01

    The experimental IR, Raman, and 1H NMR spectra of picolinic acid, as well as magnesium, calcium, strontium, and barium picolinates were registered, assigned and studied. Characteristic changes in the spectra of metal picolinates in comparison with the spectrum of ligand were observed, which lead to the conclusion that perturbation of the aromatic system of picolinates increases along with the series Mg-->Ca-->Sr-->Ba. Theoretical structures of beryllium and magnesium picolinates, as well as theoretical IR spectrum of magnesium picolinate were calculated in B3PW91/6-311++G(d, p) level. On the basis of calculated bond lengths in pyridine ring geometric, aromaticity indexes HOMA were calculated. The idea of these indexes is based on the fact that the essential factor in aromatic stabilization is the pi delocalization manifested in: planar geometry, equalization of the bond lengths and angles, and symmetry. The decidedly lower value of HOMA for magnesium picolinate (i.e. 0.545; 0.539) than that for beryllium picolinate (i.e. 0.998; 0.998) indicate higher aromatic properties of Be picolinate than of Mg picolinate. The comparison of theoretical and literature experimental structures of magnesium picolinate was done. The experimental structure contains two water molecules, so the calculations for hydrated magnesium picolinate were carried on, and the influence of coordinated water molecule on the structure of picolinates was discussed. The HOMAs for hydrated experimental and calculated Mg picolinate amount to 0.870; 0.743, and 0.900; 0.890, respectively, whereas for anhydrous structure, it is as described above, i.e. 0.545; 0.539. Thus, the calculations clearly showed that water molecules coordinated to the central atom weakens the effect of metal on the electronic system of ligand.

  10. Influence of crystallization on the spectral features of nano-sized ferroelectric barium strontium titanate (Ba{sub 0.7}Sr{sub 0.3}Tio{sub 3}) thin films

    Energy Technology Data Exchange (ETDEWEB)

    Bobby Singh, S. [Department of Physics, Manipur University, Imphal 795003, Manipur (India)], E-mail: bsoram@rediffmail.com; Sharma, H.B.; Sarma, H.N.K.; Phanjoubam, Sumitra [Department of Physics, Manipur University, Imphal 795003, Manipur (India)

    2008-08-01

    Ferroelectric barium strontium titanate (Ba{sub 0.7}Sr{sub 0.3}TiO{sub 3})(BST) thin films have been prepared from barium 2-ethylhexanoate [Ba[CH{sub 3}(CH{sub 2}){sub 3}CH(C{sub 2}H{sub 5})CO{sub 2}]{sub 2}]{sub ,} strontium 2-ethylhexanoate [Sr[CH{sub 3}(CH{sub 2}){sub 3}CH(C{sub 2}H{sub 5})CO{sub 2}]{sub 2}] and titanium(IV) isopropoxide [TiOCH(CH{sub 3}){sub 2}]{sub 4} precursors using a modified sol-gel technique. The precursor except [TiOCH(CH{sub 3}){sub 2}]{sub 4} were synthesized in the laboratory. Transparent and crack-free films were fabricated on pre-cleaned quartz substrates by spin coating. The structural and optical properties of films annealed at different temperatures have been investigated. The as-fired films were found to be amorphous that crystallized to the tetragonal phase after annealing at 550 deg. C for 1 h in air. The lattice constants 'a' and 'c' were found to be 3.974 A and 3.990 A, respectively. The grain sizes of the films annealed at 450, 500 and 550 deg. C were found to be 30.8, 36.0 and 39.8 nm respectively. The amorphous film showed very high transparency ({approx}95%), which decreases slightly after crystallization ({approx}90%). The band gap and refractive index of the amorphous and crystalline films were estimated. The optical dispersion data are also analyzed in the light of the single oscillator model and are discussed.

  11. Fabrication of barium- and strontium-doped silica/titania hollow nanoparticles and their synergetic effects on promoting neuronal differentiation by activating ERK and p38 pathways.

    Science.gov (United States)

    Kim, Sojin; Jang, Yoonsun; Oh, Wan-Kyu; Kim, Chanhoi; Jang, Jyongsik

    2014-07-01

    Pristine, barium-doped, and strontium-doped hollow nanoparticles (p-HNPs, Ba-HNP, and Sr-HNP; HNPs) are prepared by sonication-mediated etching and redeposition (SMER) method and alkali-earth-metal hydroxide solution treatment. The HNPs are investigated to facilitate synergetic neuronal differentiation through alkali-earth-metal doping and in conjunction with nerve growth factor (NGF). PC12 cells are used as model cells for neuronal differentiation. The differentiation efficiency is improved in the presence of the HNPs+NGF, and the neurite length is in the order of Sr-HNP+NGF > Ba-HNP+NGF > p-HNP+NGF > NGF. Silica/titania have increasing effect on both differentiation efficiency and neurite length, and doped barium/strontium influences additional elongation of the average neurite length. Take advantage of hollow structure, NGF is encapsulated into HNPs, and they are further applied for directly inducing differentiation. The maximum differentiation efficiency is 67% in presence of the NGF-encapsulated Sr-HNP, which was 1.3 times higher than previous research. Furthermore, the neurite length is also 2.7 times higher than MnO2 decorated poly(3,4-ethylenedioxythiophene) nanoellipsoids. Ba- and Sr-HNP may offer a possibility for novel application of metal-hybrid nanomaterials for cell differentiation, and can be expanded to other cellular applications.

  12. Synthesis of nanoparticles of barium strontium titanate using hydrothermal microwave method; Sintese de nanoparticulas de titanato de bario estroncio utilizando o metodo hidrotermal assistido por microondas

    Energy Technology Data Exchange (ETDEWEB)

    Silva, R.A.; Souza, A.E.; Teixeira, S.R. [Universidade Estadual Paulista (DFQB/FCT/UNESP), Presidente Prudente, SP (Brazil). Fac. de Ciencia e Tecnologia. Dept. de Fisica, Quimica e Biologia; Moreira, M.L.; Volanti, D.P. [Universidade Federal de Sao Carlos (LiEC/UFSCAR), SP (Brazil). Lab. Interdisciplinar de Eletroquimica e Ceramica; Longo, E. [Universidade Estadual Paulista (UNESP/LiEC), Araraquara, SP (Brazil). Lab. Interdisciplinar de Eletroquimica e Ceramica

    2009-07-01

    Nanoparticles of barium strontium titanate Ba{sub x}Sr{sub 1}-{sub x}TiO{sub 3} (BST) had been prepared, with x = 0.5, using the hydrothermal method attended by microwaves (HTMW). A solution was prepared using deionized water, barium chloride (BaCl{sub 2}.2H{sub 2}O), strontium chloride (SrCl{sub 2}.6H{sub 2}O), titanium (IV) isopropoxide (C{sub 12}H28O{sub 4}Ti) and potassium hydroxide (KOH). Afterward the solution was heated to 140 deg C in a microwave oven, at a heating rate of 140 deg C/min, and maintained at this temperature for 40 min, under a pressure of 3 to 4 bar. X-ray diffraction (DRX) and field emission scanning electron microscopy (FE-SEM) had been used in the particles characterization. DRX was used to identify the crystallized phases and the images taken from (FE-SEM) show that the material has a wide particle-size distribution with most of them between 10 and 30 nm. (author)

  13. The influences of mole composition of strontium (x) on properties of barium strontium titanate (Ba{sub 1−x}Sr{sub x}TiO{sub 3}) prepared by solid state reaction method

    Energy Technology Data Exchange (ETDEWEB)

    Sandi, Dianisa Khoirum; Supriyanto, Agus; Iriani, Yofentina, E-mail: yopen-2005@yahoo.com [Physics Department, Faculty of Mathematics and Natural Science, Sebelas Maret University (Indonesia); Jamaluddin, Anif [Physics Department, Faculty of Teacher Training and Education, Sebelas Maret University (Indonesia)

    2016-02-08

    Barium Strontium Titanate (Ba{sub 1-x}Sr{sub x}TiO{sub 3}) or BST was prepared by solid state reaction method. Raw materials are BaCO{sub 3}, SrCO{sub 3}, and TiO{sub 2}. Those materials are mixed for 8 h, pressed, and sintered at temperature 1200°C for 2 h. Mole composition of Sr (x) was varied to study its influences on structural, morphological, and electrical properties of BST. Variation of (x) are x = 0; x = 0.1; and x = 0.5. XRD patterns showed a single phase of BST, which mean that mixture of raw materials was homogenous. Crystal structure was influenced by x. BaTiO{sub 3} and Ba{sub 0.9}Ti{sub 0.1}TiO{sub 3} have tetragonal crystal structure, while Ba{sub 0.5}Sr{sub 0.5}TiO{sub 3} is cubic. The diffraction angle shifted to right side (angle larger) as the increases of x. Crystalline size of BaTiO{sub 3}, Ba{sub 0.9}Sr{sub 0.1}TiO{sub 3}, and Ba{sub 0.5}Sr{sub 0.5}TiO{sub 3} are 38.13 nm; 38.62 nm; and 37.13 nm, respectively. SEM images showed that there are still of pores which were influenced by x. Ba{sub 0.9}Sr{sub 0.1}TiO{sub 3} has densest surface (pores are few and small in size). Sawyer Tower circuit showed that BaTiO{sub 3} and Ba{sub 0.9}Sr{sub 0.1} TiO{sub 3} is ferroelectric, while Ba{sub 0.5}Sr{sub 0.5}TiO{sub 3} is paraelectric. The dielectric constants of BaTiO{sub 3}, Ba{sub 0.9}Sr{sub 0.1}TiO{sub 3} and Ba{sub 0.5}Sr{sub 0.5}TiO{sub 3} at frequency of 1 KHz are 156; 196; and 83, respectively. Ba{sub 0.9}Sr{sub 0.1}TiO{sub 3} has relatively highest dielectric constant. It is considered that Ba{sub 0.9}Sr{sub 0.1}TiO{sub 3} has densest surface.

  14. Influence of strontium on the cubic to ordered hexagonal phase transformation in barium magnesium niobate

    Indian Academy of Sciences (India)

    M Thirumal; A K Ganguli

    2000-12-01

    Oxides of the type Ba3–SrMgNb2O9 were synthesized by the solid state route. The = 0 composition (Ba3MgNb2O9) was found to crystallize in a disordered (cubic) perovskite structure when sintered at 1000C. For higher Sr doping ( ≥ 0.5), there was clearly the presence of an ordered hexagonal phase indicated by the growth of superstructure reflections in the powder X-ray diffraction patterns. In all the compositions there was the presence of a minor amount of Ba5–SrNb4O15 phase which increased with Sr substitution up to = 1 and then it remained nearly constant at about 5%. Samples sintered at 1300C showed the hexagonally ordered phase for the entire range of composition (0 ≤ ≤ 3). The degree of ordering being considerably greater than in the 1000C heated samples as evidenced by several superstructure reflections.

  15. Adsorption of Pb(II) present in aqueous solution on calcium, strontium and barium hydroxy apatites; Adsorcion de Pb(II) presente en solucion acuosa sobre hidroxiapatitas de calcio, estroncio y bario

    Energy Technology Data Exchange (ETDEWEB)

    Vilchis G, J.

    2013-07-01

    Calcium, strontium and barium hydroxy apatites were successfully synthesized by chemical precipitation method, the obtained powders were characterized by the techniques of X-ray diffraction (XRD), scanning electron microscopy (Sem), semi-quantitative elemental analysis (EDS), infrared spectroscopy (IR), and N{sub 2} physisorption studies, complementary to these analytical techniques, was determined the surface fractal dimension (Df), and the amount of surface active sites of the materials, in order to know application as ceramic for water remediation. The ability of Pb(II) ion adsorption present in aqueous solution on the hydroxy apatites synthesized by batch type experiments was studied as a function of contact time, concentration of the adsorbate and temperature. The maximum lead adsorption efficiencies obtained were 0.31, 0.32 and 0.26 mg/g for calcium, strontium and barium hydroxy apatites respectively, achieved an equilibrium time of 20 minutes in the three solid-liquid systems studied. Experimental data were adequately adjusted at the adsorption kinetic model pseudo-second order, for the three cases. Moreover, experimental data of the strontium and calcium hydroxy apatites were adjusted to the Langmuir adsorption isotherm, indicating that the adsorption was through a monolayer, whereas barium hydroxyapatite was adjusted to the Freundlich adsorption isotherm, indicating a multilayer adsorption. The thermodynamic parameters obtained during adsorption studies as a function of temperature showed physisorption, exothermic and spontaneous processes respectively. The results showed that the calcium hydroxyapatite, strontium and barium are an alternative for the Pb(II) ion adsorption present in wastewaters. (Author)

  16. High temperature dielectric relaxation anomaly of Y³⁺ and Mn²⁺ doped barium strontium titanate ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Yan, Shiguang; Mao, Chaoliang, E-mail: maochaoliang@mail.sic.ac.cn, E-mail: xldong@mail.sic.ac.cn; Wang, Genshui; Yao, Chunhua; Cao, Fei; Dong, Xianlin, E-mail: maochaoliang@mail.sic.ac.cn, E-mail: xldong@mail.sic.ac.cn [Key Laboratory of Inorganic Functional Materials and Devices, Shanghai Institute of Ceramics, Chinese Academy of Sciences, 1295 Dingxi Road, Shanghai 200050 (China)

    2014-10-14

    Relaxation like dielectric anomaly is observed in Y³⁺ and Mn²⁺ doped barium strontium titanate ceramics when the temperature is over 450 K. Apart from the conventional dielectric relaxation analysis method with Debye or modified Debye equations, which is hard to give exact temperature dependence of the relaxation process, dielectric response in the form of complex impedance, assisted with Cole-Cole impedance model corrected equivalent circuits, is adopted to solve this problem and chase the polarization mechanism in this paper. Through this method, an excellent description to temperature dependence of the dielectric relaxation anomaly and its dominated factors are achieved. Further analysis reveals that the exponential decay of the Cole distribution parameter n with temperature is confirmed to be induced by the microscopic lattice distortion due to ions doping and the interaction between the defects. At last, a clear sight to polarization mechanism containing both the intrinsic dipolar polarization and extrinsic distributed oxygen vacancies hopping response under different temperature is obtained.

  17. Analysis of the optical properties of Er{sup 3+}-doped strontium barium niobate nanocrystals using time-resolved laser spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Kowalska, D.; Haro-Gonzalez, P. [Universidad de La Laguna, Departamento de Fisica Fundamental, Experimental, Electronica y Sistemas, La Laguna, Tenerife (Spain); Martin, I.R. [Universidad de La Laguna, Departamento de Fisica Fundamental, Experimental, Electronica y Sistemas, La Laguna, Tenerife (Spain); Malta Consolider Team, La Laguna, Tenerife (Spain); Caceres, J.M. [Universidad de La Laguna, Departamento de Edafologia y Geologia, La Laguna, Tenerife (Spain)

    2010-06-15

    This paper reports the results obtained in strontium barium niobate (SBN) nanocrystals in glasses doped with 1, 2.5 and 5 mol% of Er{sup 3+} ions. The melt-quenching method was applied to fabricate the glasses with composition SrO-BaO-Nb{sub 2}O{sub 5}-B{sub 2}O{sub 3} and further thermal treatment was used to obtain glass ceramic samples from the glass precursor. X-ray diffraction patterns confirmed the formation of SBN nanocrystals with an average size of about 50 nm in diameter. Time-resolved fluorescence spectra for the emission of Er{sup 3+} ions at 1550 nm have been analyzed in order to confirm the incorporation of the Er{sup 3+} ions into the nanocrystals. Green frequency upconversion emission under excitation at 975 nm coming from the ions in the nanocrystals has been obtained. This intense upconversion is about a factor of 500 higher than that obtained from the ions which reside in the glassy phase. Moreover, temporal evolution studies have been carried out with the purpose of determining the involved upconversion mechanism and the importance of these processes as a source of losses for the optical amplification at 1550 nm. (orig.)

  18. Structural characterization and ferroelectric properties of strontium barium niobate (Sr xBa1-xNb2O6 thin films

    Directory of Open Access Journals (Sweden)

    R.G. Mendes

    2001-01-01

    Full Text Available Strontium barium niobate (SBN thin films of good quality were deposited on Pt/Ti/SiO2/Si substrate using a polymeric resin containing metallic ions. Films were crystallized at different temperatures and for different duration of time. The structure of these films was studied using X-ray diffraction. The coexistence of SrNb2O6 (SN and SBN was observed in films crystallized at 700 °C. The amount of SN decreases when the crystallization time increases. Ferroelectric properties were determined for films crystallized at 700 °C for 1 and 5 h. For SBN film crystallized at 700 °C for 1 h, the remanent polarization (Pr and the coercive field (Ec were 2.6 muC/cm² and 71.9 kV/cm, respectively. For the film crystallized at 700 °C for 5 h these parameters were Pr = 1.1 muC/cm² and Ec = 50.5 kV/cm.

  19. Effect of working pressure and annealing temperature on microstructure and surface chemical composition of barium strontium titanate films grown by pulsed laser deposition

    Indian Academy of Sciences (India)

    Zahra Saroukhani; Nemat Tahmasebi; Seyed Mohammad Mahdavi; Ali Nemati

    2015-10-01

    Barium strontium titanate (BST, Ba1−SrTiO3) thin films have been extensively used in many dielectric devices such as dynamic random access memories (DRAMs). To optimize its characteristics, a microstructural control is essential. In this paper, Ba0.6Sr0.4TiO3 thin film has been deposited on the SiO2/Si substrate by the pulsed laser deposition (PLD) technique at three different oxygen working pressures of 100, 220 and 350 mTorr. Then the deposited thin films at 100 mTorr oxygen pressure were annealed for 50 min in oxygen ambient at three different temperatures: 650, 720 and 800°C. The effect of oxygen working pressure during laser ablation and thermal treatment on the films was investigated by using X-ray diffraction (XRD), atomic force microscopy (AFM) and scanning electron microscopy (SEM) analysis methods. X-ray photoelectron spectroscopy analysis was used to determine the surface chemical composition of the samples. The results indicate that the deposited BST film at low working pressure (100 mTorr) in PLD chamber shows a lower surface roughness than other working pressures (220 and 350 mTorr). The as-deposited films show an amorphous structure and would turn into polycrystalline structure at annealing temperature above 650°C. Increase of temperature would cause the formation of cubic and per-ovskite phases, improvement in crystalline peaks and also result in the decomposition of BST at high temperature (above 800°C). In addition, rising of temperature leads to the increase in size of grains and clusters. Therefore more roughness was found at higher temperatures as a result of a more heterogeneous growth and less tensions.

  20. Structure and properties of barium tin boro-phosphate glass systems with very low photoelastic constant

    Science.gov (United States)

    Itadani, M.; Tricot, G.; Doumert, B.; Takebe, H.; Saitoh, A.

    2017-08-01

    Glasses in the BaO-SnO-P2O5-B2O3 system were prepared and evaluated in order to formulate preform glasses suitable for the fabrication of fiber cores with a very low photoelastic constant. A first glass system (I: xBaO-(60-x)SnO-40P2O5) was designed with a constant P2O5 content and various BaO contents (0-40 mol. %). Introduction of 3 mol. % of B2O3 to enhance the glass stability leads to the second glass system (II: x'BaO-(57-x')SnO-40P2O5-3B2O3) with 33-38 mol. % BaO. The structure of both systems was investigated by 1D/2D magic-angle spinning nuclear magnetic resonance, Raman, and Fourier transform infrared spectroscopic techniques. 31P NMR showed the presence of Q2 and Q1 units in the first system and correlation 11B/31P NMR indicated that boron enters into the network as B(OP)4 structural units. The photoelastic constant was determined and the stability of the best formulations as well as their refractive index dispersion was established. The drawing temperature and isothermal heating time (without crystal precipitation) parameters were also accurately measured by using experimental time-temperature-transition. Considering that the refractive indices of the core and the cladding materials must match, detailed core and cladding compositions for a fiber enabling single-mode waveguide transmission were proposed.

  1. Elasticity study of textured barium strontium titanate thin films by X-ray diffraction and laser acoustic waves

    Science.gov (United States)

    Chaabani, Anouar; Njeh, Anouar; Donner, Wolfgang; Klein, Andreas; Hédi Ben Ghozlen, Mohamed

    2017-05-01

    Ba0.65Sr0.35TiO3 (BST) thin films of 300 nm were deposited on Pt(111)/TiO2/SiO2/Si(001) substrates by radio frequency magnetron sputtering. Two thin films with different (111) and (001) fiber textures were prepared. X-ray diffraction was applied to measure texture. The raw pole figure data were further processed using the MTEX quantitative texture analysis software for plotting pole figures and calculating elastic constants and Young’s modulus from the orientation distribution function (ODF) for each type of textured fiber. The calculated elastic constants were used in the theoretical studies of surface acoustics waves (SAW) propagating in two types of multilayered BST systems. Theoretical dispersion curves were plotted by the application of the ordinary differential equation (ODE) and the stiffness matrix methods (SMM). A laser acoustic waves (LAW) technique was applied to generate surface acoustic waves (SAW) propagating in the BST films, and from a recursive process, the effective Young’s modulus are determined for the two samples. These methods are used to extract and compare elastic properties of two types of BST films, and quantify the influence of texture on the direction-dependent Young’s modulus.

  2. Determination of Iron Calcium and Strontium in Barium Sulfate by Atomic Absorption Spectrometry%原子吸收光谱法测定硫酸钡中铁钙锶

    Institute of Scientific and Technical Information of China (English)

    闫希变

    2012-01-01

    以重晶石为原料煅烧法生产的硫酸钡中含有铁、钙、锶等无机离子,无机离子的存在会对下游产品的质量有重要影响.为了快速准确地测定硫酸钡中铁、钙、锶含量,通过大量实验确立了硫酸钡中铁、钙、锶含量的测定方法.用盐酸煮沸溶解样品,过滤后用原子吸收光谱法测定.此法准确快速,精密度高.实测样品中铁、钙和锶的回收率分别为98.7%~103.6%、101.27%~ 103.26%、98.55%~101.1%、相对标准偏差(n=6)分别为2.37%、2.29%、1.29%.%Barium sulfate produced with barite by calcinationcalcination contained iron, calcium, strontium and other inorganic ions which have important influence on the quality of the downstream products. In order to determine iron, calcium, strontium contents of barium sulfate rapidly and accurately, a method for the determination of iron, calcium and strontium contents in barium sulfate was confirmed through the massive experiments. The sample is dissolved with hydrochloric acid, which is assaied by atomic absorption spectrometry after filtered. This method is quick and accurate ,more precise . With this method, the standard sample recovery rate of iron, calcium, strontium were 98. 7% ~ 103. 6% , 101. 27% ~ 103. 26% , 98. 55% - 101. 1% , the relative standard deviation( n = 6) were 2.37% , 2.29% , 1.29%.

  3. Effect of rare earth substitution on properties of barium strontium titanate ceramic and its multiferroic composite with nickel cobalt ferrite

    Energy Technology Data Exchange (ETDEWEB)

    Pahuja, Poonam [Department of Physics and Astrophysics, University of Delhi, Delhi 110007 (India); Kotnala, R.K. [National Physical Laboratory, Delhi 110012 (India); Tandon, R.P., E-mail: rt241150@gmail.com [Department of Physics and Astrophysics, University of Delhi, Delhi 110007 (India)

    2014-12-25

    Highlights: • Rare earth ions Dy{sup 3+}, Gd{sup 3+} and Sm{sup 3+} have been substituted in Ba{sub 0.95}Sr{sub 0.05}TiO{sub 3} (BST). • Ni{sub 0.8}Co{sub 0.2}Fe{sub 2}O{sub 4} has been used as ferrimagnetic phase to obtain composites. • Substitution of these ions increases dielectric constant of BST and composites. • Magnetoelectric coefficient of composites increases on substitution of these ions. - Abstract: Effect of substitution of rare earth ions (Dy{sup 3+}, Gd{sup 3+} and Sm{sup 3+}) on various properties of Ba{sub 0.95}Sr{sub 0.05}TiO{sub 3} (BST) i.e. the composition Ba{sub 0.95−1.5x}Sr{sub 0.05}R{sub x}TiO{sub 3} (where x = 0.00, 0.01, 0.02, 0.03 and R are rare earths Dy, Gd, Sm) and that of their multiferroic composite with Ni{sub 0.8}Co{sub 0.2}Fe{sub 2}O{sub 4} (NCF) has been studied. Shifting of peaks corresponding to different compositions in the X-ray diffraction pattern confirmed the substitution of rare earth ions at both Ba{sup 2+} and Ti{sup 4+} sites in BST. It is clear from scanning electron microscopy (SEM) images that rare earth substitution in BST increases its grain size in both pure and composite samples. Substitution of rare earth ions results in increase in value of dielectric constant of pure and composite samples. Sm substitution in BST significantly decreases its Curie temperature. Dy substituted pure and composite samples possess superior ferroelectric properties as confirmed by polarization vs electric field (P–E) loops. Composite samples containing Dy, Gd and Sm substituted BST as ferroelectric phase possess lower values of remanent and saturation magnetizations in comparison to composite sample containing pure BST as ferroelectric phase (BSTC). Rare earth substituted composite samples possess higher value of magnetoelectric coefficient as compared to that for BSTC.

  4. Third-Order Electric-Field-Induced Dipolar Resonances from Patterned Barium-Strontium-Titanate Thin-Films

    Science.gov (United States)

    Toonen, Ryan; Will Cole, Melanie; Ivill, Mathew; Hirsch, S.; Integrated Electromagnetic Materials Team Team

    2013-03-01

    Using microwave reflection spectroscopy, the complex permittivities of etch-defined, 240 nm thick, [Ba(0.6)Sr(0.4)]TiO(3), thin films were measured over the frequency range of (1 to 4) GHz. The observed electro-acoustic resonances were characterized as a function of extrinsic electric field magnitude, ambient temperature, and sample diameter. The real and imaginary parts of the measured permittivities were fit to frequency-dependent functions derived from the Lorentz oscillator model. From these functions, extracted static dielectric constants were found to display excellent agreement with a closed-form expression derived by calculating third-order nonlinear susceptibility from the Landau-Devonshire-Ginzberg model [R. C. Toonen and M. W. Cole, Appl. Phys. Lett. 100, 222908 (2012)]. By investigating the behavior of these loss mechanisms in response to external stimuli, we have gained insight with respect to how such effects can be reduced or even eliminated. It is also possible that these loss mechanisms could be exploited for the purpose of engineering micro-/nano-electro-mechanical resonators and super-compact high-quality-factor frequency-selective filters. Funding for these efforts was provided by an award from the ARL Director's Research Initiative (FY10-WMR-27).

  5. Microstructure and relaxor ferroelectric properties of Bi{sub 2}O{sub 3}-doped strontium barium niobate ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Li, Jinglei, E-mail: lilei19871003@yahoo.com.cn; Pu, Yongping; Wang, Zhuo; Dong, Zijing; Dai, Jie

    2013-11-01

    Highlights: • Bi{sub 2}O{sub 3} addition could promote the grain growth in Sr{sub 0.4}Ba{sub 0.6}Nb{sub 2}O{sub 6} ceramics. • Doping Bi{sub 2}O{sub 3} could improve the dielectric constant and lower the dielectric loss. • The dielectric characteristics of doping Bi{sub 2}O{sub 3} samples showed relaxation behavior. • The P–E hysteresis loops for doping Bi{sub 2}O{sub 3} ceramics became slimmer. -- Abstract: (1 − x) Sr{sub 0.4}Ba{sub 0.6}Nb{sub 2}O{sub 6}–xBi{sub 2}O{sub 3} (0.00 ≤ x ≤ 0.20) ceramics were prepared by conventional solid-state reaction method. The microstructure, dielectric properties and P–E hysteresis loops of ceramics were investigated via X-ray diffraction, scanning electron microscope (SEM), Agilent E4980A and modified Sawyer–Tower circuit, respectively. XRD results showed the obtained ceramics were of tungsten bronze structure, and second phase Sr{sub 0.4}Ba{sub 0.6}Bi{sub 2}Nb{sub 2}O{sub 9} was detected at high doping concentration. SEM results showed suitable Bi{sub 2}O{sub 3} addition could reduce the sintering temperature and assist the grain growth. The dielectric characteristics exhibited diffuse phase transition phenomena, which were verified by linear fitting of the modified Curie–Weiss law. Besides, the relaxor ferroelectric properties of ceramics followed the Vogel–Fulcher relationship well. The P–E hysteresis loops became slimmer with increasing the Bi{sub 2}O{sub 3} addition, leading to a gradually decrease in both remnant polarization (P{sub r}) and coercive field (E{sub c})

  6. Concentrations of strontium, barium, cadmium, copper, zinc, manganese, chromium, antimony, selenium, and lead in the liver and kidneys of dogs according to age, gender, and the occurrence of chronic kidney disease.

    Science.gov (United States)

    Passlack, Nadine; Mainzer, Barbara; Lahrssen-Wiederholt, Monika; Schafft, Helmut; Palavinskas, Richard; Breithaupt, Angele; Zentek, Jürgen

    2015-01-01

    This study was conducted to measure the concentrations of strontium (Sr), barium (Ba), cadmium (Cd), copper (Cu), zinc (Zn), manganese (Mn), chromium (Cr), antimony (Sb), selenium (Se), and lead (Pb) in canine liver, renal cortex, and renal medulla, and the association of these concentrations with age, gender, and occurrence of chronic kidney disease (CKD). Tissues from 50 dogs were analyzed using inductively coupled plasma mass spectrometry. Cu, Zn, and Mn levels were highest in the liver followed by the renal cortex and renal medulla. The highest Sr, Cd, and Se concentrations were measured in the renal cortex while lower levels were found in the renal medulla and liver. Female dogs had higher tissue concentrations of Sr (liver and renal medulla), Cd (liver), Zn (liver and renal cortex), Cr (liver, renal cortex, and renal medulla), and Pb (liver) than male animals. Except for Mn and Sb, age-dependent variations were observed for all element concentrations in the canine tissues. Hepatic Cd and Cr concentrations were higher in dogs with CKD. In conclusion, the present results provide new knowledge about the storage of specific elements in canine liver and kidneys, and can be considered important reference data for diagnostic methods and further investigations.

  7. Efficient 1.54-μm emission through Eu{sup 2+} sensitization of Er{sup 3+} in thin films of Eu{sup 2+}/Er{sup 3+} codoped barium strontium silicate under broad ultraviolet light excitation

    Energy Technology Data Exchange (ETDEWEB)

    Li, Leliang; Zheng, Jun, E-mail: zhengjun@semi.ac.cn; Zuo, Yuhua; Cheng, Buwen; Wang, Qiming

    2015-01-15

    Thin films of Eu{sup 2+}/Er{sup 3+} codoped barium strontium silicate were deposited on a thermal oxide Si substrate by magnetron sputtering. Optical properties suggest that after a rapid annealing process, these films can lead to efficient Er{sup 3+} emission at 1.54 μm with a lifetime of about 7.9 ms. Intense 1.54-μm light emission was achieved under broad ultraviolet light excitation through efficient energy transfer from Eu{sup 2+} to Er{sup 3+}. These results indicate that the Eu{sup 2+}/Er{sup 3+} thin films have potential applications as low cost and compact erbium doped waveguide amplifiers pumped by LEDs. - Highlights: • The Er{sub 0.07}Eu{sub 0.14}Sr{sub 1.14}Ba{sub 0.79}SiO{sub 4} films are fabricated by magnetron sputtering. • Efficient energy transfer from Eu{sup 2+} to Er{sup 3+} ions by the dipole–dipole interaction. • Intense 1.54 μm emission is achieved under broad excitation spectrum. • The films have potential applications as low cost and compact EDWAs.

  8. Rb-Sr age and content of potassium, rubidium strontium, barium, and rare earths in surface material from the Sea of Fertility

    Science.gov (United States)

    Allegre, C. J.; Birck, J. L.; Loubet, M.; Provost, A.

    1974-01-01

    The Luna 16 automatic station returned from the Sea of Fertility a 35 cm long column of lunar surface material. 1 g of the Luna 16 lunar surface material, taken at a depth of 22 cm, consists of fine material: surface material and fine fragments of rocks from 1 to 4 mm in diameter. Analyses made on 17 mg of the fine lunar surface material are presented. The results obtained for the Luna 16 surface material are plotted on the diagram of the isotopic evolution of strontium and show that this surface material is most depleted of radiogenic Sr-87 of all the known lunar surface materials and that the point characterizing Lunar 16 lies somewhat to the right of the line corresponding to an age of 4.6 billion years.

  9. Structural characterization combined with the first principles simulations of barium/strontium cobaltite/ferrite as promising material for solid oxide fuel cells cathodes and high-temperature oxygen permeation membranes.

    Science.gov (United States)

    Gangopadhayay, Shruba; Inerbaev, Talgat; Masunov, Artëm E; Altilio, Deanna; Orlovskaya, Nina

    2009-07-01

    Mixed ionic-electronic conducting perovskite type oxides with a general formula ABO(3) (where A = Ba, Sr, Ca and B = Co, Fe, Mn) often have high mobility of the oxygen vacancies and exhibit strong ionic conductivity. They are key materials that find use in several energy related applications, including solid oxide fuel cell (SOFC), sensors, oxygen separation membranes, and catalysts. Barium/strontium cobaltite/ferrite (BSCF) Ba(0.5)Sr(0.5)Co(0.8)Fe(0.2)O(3-delta) was recently identified as a promising candidate for cathode material in intermediate temperature SOFCs. In this work, we perform experimental and theoretical study of the local atomic structure of BSFC. Micro-Raman spectroscopy was performed to characterize the vibrational properties of BSCF. The Jahn-Teller distortion of octahedral coordination around Co(4+) cations was observed experimentally and explained theoretically. Different cations and oxygen vacancies ordering are examined using plane wave pseudopotential density functional theory. We find that cations are completely disordered, whereas oxygen vacancies exhibit a strong trend for aggregation in L-shaped trimer and square tetramer structure. On the basis of our results, we suggest a new explanation for BSCF phase stability. Instead of linear vacancy ordering, which must take place before the phase transition into brownmillerite structure, the oxygen vacancies in BSCF prefer to form the finite clusters and preserve the disordered cubic structure. This structural feature could be found only in the first-principles simulations and can not be explained by the effect of the ionic radii alone.

  10. Synthesis and investigations of new strontium dicarboxylates

    Energy Technology Data Exchange (ETDEWEB)

    Grzesiak-Nowak, Marta [Polish Academy of Sciences, Krakow (Poland). Jerzy Haber Institute of Catalysis and Surface Chemistry; Nitek, Wojciech; Rafalska-Lasocha, Alicja [Jagiellonian Univ., Krakow (Poland). Faculty of Chemistry; Lasocha, Wieslaw [Polish Academy of Sciences, Krakow (Poland). Jerzy Haber Institute of Catalysis and Surface Chemistry; Jagiellonian Univ., Krakow (Poland). Faculty of Chemistry

    2013-07-01

    Using simple methods of synthesis without template agents, 6 new compounds of strontium and dicarboxylic acids have been obtained. The resulting salts are: {l_brace}1{r_brace} strontium glutarate pentahydrate, {l_brace}2{r_brace} strontium adipate, {l_brace}3{r_brace} strontium pimelate monohydrate, {l_brace}4{r_brace} strontium suberate, {l_brace}5{r_brace} strontium azelate and {l_brace}6{r_brace} strontium dodecanedioate hemihydrate. Similarly to the known barium compounds, starting from the salt of azelaic acid, strontium compounds with longer dicarboxylic acids form acidic salts. Metal centers have the coordination number C.N. = 8, and the coordination polyhedra are dodecahedra. Glutaric acid form layered material, whereas with use of longer acids 3D systems are formed. Acids such as dodecanedioic and azealic form systems in which Sr-O polyhedra do not share edges or vertices. Isolated SrO{sub 8} polyhedra are joined by carboxylic groups of dicarboxylic acids. Strontium salts {l_brace}2, 4, 5{r_brace} are anhydrous, but {l_brace}1{r_brace} is pentahydrate, {l_brace}3{r_brace} is monohydrate, and {l_brace}6{r_brace} is hemihydrate. During thermal decomposition strontium salts of dicarboxylic acids decompose through an unknown intermediate product to strontium carbonate. (orig.)

  11. Structural and Electrical Properties of Barium Strontium Titanate Thin Film on Conductive La1_xSrxMnO3 Bottom Layer

    Institute of Scientific and Technical Information of China (English)

    MIAO Jun; QIU Xiang-Gang; CAO Li-Xin; ZHAO Bai-Ru; CHEN Wei-Ran; CHEN Bin; YANG Hao; PENG Wei; ZHONG Jian-Pin; WU Hao; YUAN Jie; XU Bo

    2004-01-01

    @@ Ferroelectrics and colossal magnetoresistance heterostructure Bal-xSrx TiO3 (BST)/La1- xSrx MnO3 (LSMO) have been fabricated on a LaAlO3 substrate by the pulse laser deposition method. The dielectric measurements show that at room temperature and 100kHz, the dielectric constant and loss tangent are about 990 and 0.012, respectively; the highest tunability is about 45% near 200 K under the applied electric field of 200 k V/cm. Further study indicates that the leakage current for the BST/LSMO heterostructure obeys the Schottky emission mechanism in the electric field region higher than 100kV/cm at room temperature.

  12. Flexoelectricity in barium strontium titanate thin film

    Energy Technology Data Exchange (ETDEWEB)

    Kwon, Seol Ryung; Huang, Wenbin; Yuan, Fuh-Gwo; Jiang, Xiaoning, E-mail: xjiang5@ncsu.edu [Department of Mechanical and Aerospace Engineering, North Carolina State University, Raleigh, North Carolina 27695 (United States); Shu, Longlong [Department of Mechanical and Aerospace Engineering, North Carolina State University, Raleigh, North Carolina 27695 (United States); Electronic Materials Research Laboratory, International Center for Dielectric Research, Xi' an Jiao Tong University, Xi' an, Shaanxi 710049 (China); Maria, Jon-Paul [Department of Material Science and Engineering, North Carolina State University, Raleigh, North Carolina 27695 (United States)

    2014-10-06

    Flexoelectricity, the linear coupling between the strain gradient and the induced electric polarization, has been intensively studied as an alternative to piezoelectricity. Especially, it is of interest to develop flexoelectric devices on micro/nano scales due to the inherent scaling effect of flexoelectric effect. Ba{sub 0.7}Sr{sub 0.3}TiO{sub 3} thin film with a thickness of 130 nm was fabricated on a silicon wafer using a RF magnetron sputtering process. The flexoelectric coefficients of the prepared thin films were determined experimentally. It was revealed that the thin films possessed a transverse flexoelectric coefficient of 24.5 μC/m at Curie temperature (∼28 °C) and 17.44 μC/m at 41 °C. The measured flexoelectric coefficients are comparable to that of bulk BST ceramics, which are reported to be 10–100 μC/m. This result suggests that the flexoelectric thin film structures can be effectively used for micro/nano-sensing devices.

  13. Elevated silver, barium and strontium in antlers, vegetation and soils sourced from CWD cluster areas: do Ag/Ba/Sr piezoelectric crystals represent the transmissible pathogenic agent in TSEs?

    Science.gov (United States)

    Purdey, Mark

    2004-01-01

    High levels of Silver (Ag), Barium (Ba) and Strontium (Sr) and low levels of copper (Cu) have been measured in the antlers, soils and pastures of the deer that are thriving in the chronic wasting disease (CWD) cluster zones in North America in relation to the areas where CWD and other transmissible spongiform encephalopathies (TSEs) have not been reported. The elevations of Ag, Ba and Sr were thought to originate from both natural geochemical and artificial pollutant sources--stemming from the common practise of aerial spraying with 'cloud seeding' Ag or Ba crystal nuclei for rain making in these drought prone areas of North America, the atmospheric spraying with Ba based aerosols for enhancing/refracting radar and radio signal communications as well as the spreading of waste Ba drilling mud from the local oil/gas well industry across pastureland. These metals have subsequently bioconcentrated up the foodchain and into the mammals who are dependent upon the local Cu deficient ecosystems. A dual eco-prerequisite theory is proposed on the aetiology of TSEs which is based upon an Ag, Ba, Sr or Mn replacement binding at the vacant Cu/Zn domains on the cellular prion protein (PrP)/sulphated proteoglycan molecules which impairs the capacities of the brain to protect itself against incoming shockbursts of sound and light energy. Ag/Ba/Sr chelation of free sulphur within the biosystem inhibits the viable synthesis of the sulphur dependent proteoglycans, which results in the overall collapse of the Cu mediated conduction of electric signals along the PrP-proteoglycan signalling pathways; ultimately disrupting GABA type inhibitory currents at the synapses/end plates of the auditory/circadian regulated circuitry, as well as disrupting proteoglycan co-regulation of the growth factor signalling systems which maintain the structural integrity of the nervous system. The resulting Ag, Ba, Sr or Mn based compounds seed piezoelectric crystals which incorporate PrP and ferritin into

  14. Synthesis and characterization of nickel oxide doped barium strontium titanate ceramics Síntese e caracterização de cerâmicas de titanato de estrôncio e bário dopado com óxido de níquel

    Directory of Open Access Journals (Sweden)

    M. Banerjee

    2012-03-01

    Full Text Available Barium strontium titanate (BST ceramics (Ba0.6Sr0.4TiO3 were synthesized by solid state sintering using barium carbonate, strontium carbonate and rutile as the precursor materials. The samples were doped with nickel oxide in different proportions. Different phases present in the sintered samples were determined from X-ray diffraction investigation and the distribution of different phases in the microstructure was assessed from scanning electron microscopy study. It was observed that the dielectric properties of BST were modified significantly with nickel oxide doping. These ceramics held promise for applications in tuned circuits.Cerâmicas de titanato de bário e estrôncio (TBS (Ba0,6Sr0,4TiO3 foram sintetizadas por sinterização do estado sólido usando carbonato de bário, carbonato de estrôncio e rutilo como materiais precursores. As amostras foram dopadas com diferentes proporções de óxido de níquel. Diferentes fases presentes nas amostras sinterizadas foram determinadas por difração de raios X e a distribuição de diferentes fases na microestrutura foi avaliada por microscopia eletrônica de varredura. Foi observado que as propriedades dielétricas do TBS foram modificadas significativamente com a dopagem do óxido de níquel. Essas cerâmicas são promissoras para aplicação em dispositivos.

  15. Processing science of barium titanate

    Science.gov (United States)

    Aygun, Seymen Murat

    Barium titanate and barium strontium titanate thin films were deposited on base metal foils via chemical solution deposition and radio frequency magnetron sputtering. The films were processed at elevated temperatures for densification and crystallization. Two unifying research goals underpin all experiments: (1) To improve our fundamental understanding of complex oxide processing science, and (2) to translate those improvements into materials with superior structural and electrical properties. The relationships linking dielectric response, grain size, and thermal budget for sputtered barium strontium titanate were illustrated. (Ba 0.6Sr0.4)TiO3 films were sputtered on nickel foils at temperatures ranging between 100-400°C. After the top electrode deposition, the films were co-fired at 900°C for densification and crystallization. The dielectric properties were observed to improve with increasing sputter temperature reaching a permittivity of 1800, a tunability of 10:1, and a loss tangent of less than 0.015 for the sample sputtered at 400°C. The data can be understood using a brick wall model incorporating a high permittivity grain interior with low permittivity grain boundary. However, this high permittivity value was achieved at a grain size of 80 nm, which is typically associated with strong suppression of the dielectric response. These results clearly show that conventional models that parameterize permittivity with crystal diameter or film thickness alone are insufficiently sophisticated. Better models are needed that incorporate the influence of microstructure and crystal structure. This thesis next explores the ability to tune microstructure and properties of chemically solution deposited BaTiO3 thin films by modulation of heat treatment thermal profiles and firing atmosphere composition. Barium titanate films were deposited on copper foils using hybrid-chelate chemistries. An in-situ gas analysis process was developed to probe the organic removal and the

  16. Solid solution barium–strontium chlorides with tunable ammonia desorption properties and superior storage capacity

    DEFF Research Database (Denmark)

    Bialy, Agata; Jensen, Peter Bjerre; Blanchard, Didier

    2015-01-01

    with spray drying and in situ thermogravimetric and structural characterization, we synthesize a range of new, stable barium-strontium chloride solid solutions with superior ammonia storage densities. By tuning the barium/strontium ratio, different crystallographic phases and compositions can be obtained......Metal halide ammines are very attractive materials for ammonia absorption and storage—applications where the practically accessible or usable gravimetric and volumetric storage densities are of critical importance. Here we present, that by combining advanced computational materials prediction...... with different ammonia ab- and desorption properties. In particular it is shown, that in the molar range of 35–50% barium and 65–50% strontium, stable materials can be produced with a practically usable ammonia density (both volumetric and gravimetric) that is higher than any of the pure metal halides...

  17. Barium periostitis: an intraoral complication following barium swallow.

    Science.gov (United States)

    Stanton, David C; Seeger, Douglas; Robinson, Brian T

    2007-05-01

    Barium is used with great frequency for various gastrointestinal radiographic studies. Complications arising from the use of barium are uncommon and can range from peritonitis, pneumonitis, vascular intravasation, allergic reactions, and even "barium appendicitis." We report a case of an unusual complication, periostitis, from the use of barium in a 46-year-old male.

  18. Determination of forbidden and restricted elements lead, cadmium, arsenic, mercury, antimony, chromium, nickel, barium and strontium in cosmetic products by ICP-AES%ICP-AES法测定化妆品中铅、镉、砷、汞、锑、铬、镍、钡、锶等禁限用元素含量

    Institute of Scientific and Technical Information of China (English)

    戴骐; 林晓娜; 吴艳燕; 楼士铭; 陈俊晓

    2012-01-01

    建立了化妆品中铅(Pb)、镉(Cd)、砷(As)、汞(Hg)、锑(Sb)、铬(Cr)、镍(Ni)、钡(Ba)、锶(Sr)含量的电感耦合等离子体原子发射光谱法(ICP-AES)同步检测技术.采用微波消解,在较难消化的化妆品中加HF进行消化,铑(Rh)为内标元素消除基体干扰,以配备耐HF进样系统的ICP-AES进行测定.在0~1.0 mg/L 范围内呈现良好的线性关系(相关系数≥0.9999),Pb、Cd、As、Hg、Sb、Cr、Ni、Ba、Sr 检出限分别为0.0016,0.0007,0.0021,0.0013,0.0003,0.0009,0.0008,0.0009,0.0021 mg/L,方法回收率80.2%~111%,精密度1.7%~8.2%.结果表明,该方法适用于检测基体复杂的化妆品中Pb、Cd、As、Hg、Sb、Cr、Ni、Ba、Sr.%A method for the determination of the forbidden and restricted elements lead(Pb), cadmium (Cd), arsenic (As), mercur(Hg), antimony (Sb), Chroium(Cr), Nickel (Ni) , barium (Ba)and strontiume (Sr) in cosmetic products by inductively coupled plasma mass spectrometry( ICP-AES) was developed. The sample was microwave digested with HNO3 H2O2 and HF, then detected by ICP-AES. This method achieves practical quantitation limits for the 9 elements of 0.0016,0.0007,0.0021,0.0013,0.0003,0. 0009,0.0008,0.0009, 0. 0021 mg/L, respectively. The correlation coefficients of calibration curves in the range of 0 to 1.0 mg/L were more than 0. 9999. The recoveries and precision of the method were 80. 2% -111% and 1. 7% ~ 8. 2%. This level of measurement allows for the accurate assessment of 9 forbidden and restricted elements in cosmetic food.

  19. Both barium and calcium activate neuronal potassium currents

    Energy Technology Data Exchange (ETDEWEB)

    Ribera, A.B.; Spitzer, N.C.

    1987-09-01

    Amphibian spinal neurons in culture possess both rapidly inactivating and sustained calcium-dependent potassium current components, similar to those described for other cells. Divalent cation-dependent whole-cell outward currents were isolated by subtracting the voltage-dependent potassium currents recorded from Xenopus laevis neurons in the presence of impermeant cadmium from the currents produced without cadmium but in the presence of permeant divalent cations. These concentrations of permeant ions were low enough to avoid contamination by macroscopic inward currents through calcium channels. Calcium-dependent potassium currents were reduced by 1 ..mu..M tetraethylammonium. These currents can also be activated by barium or strontium. Barium as well as calcium activated outward currents in young neurons (6-8 hr) and in relatively mature neurons (19-26 hr in vitro). However, barium influx appeared to suppress the sustained voltage-dependent potassium current in most cells. Barium also activated at least one class of potassium channels observed in excised membrane patches, whole blocking others. The blocking action may have masked and hindered detection of the stimulatory action of barium in other systems.

  20. STRONTIUM AND BARIUM IN EARLY-TYPE GALAXIES

    Energy Technology Data Exchange (ETDEWEB)

    Conroy, Charlie [Department of Astronomy and Astrophysics, University of California, Santa Cruz, CA (United States); Van Dokkum, Pieter G. [Department of Astrophysical Sciences, Yale University, New Haven, CT (United States); Graves, Genevieve J. [Department of Astronomy, University of California, Berkeley, CA (United States)

    2013-02-01

    The detailed abundance patterns of the stars within galaxies provide a unique window into the history of star formation (SF) at early times. Two widely used 'chronometers' include the {alpha} and iron-peak elements, which are created on short and long timescales, respectively. These two clocks have been widely used to estimate SF timescales from moderate-resolution spectra of early-type galaxies. Elements formed via s-process neutron captures (e.g., Sr and Ba) comprise a third type of chronometer, as the site of the main s-process is believed to be intermediate and low-mass asymptotic giant branch stars. The [{alpha}/Ba] ratio in particular should provide a powerful new constraint on the SF histories of galaxies, in part because it is insensitive to the uncertain distribution of Type Ia supernovae detonation times and the overall Ia rate. Here we present new measurements of the abundance of Sr and Ba in nearby early-type galaxies by applying stellar population synthesis tools to high signal-to-noise optical spectra. We find a strong anti-correlation between [Mg/Fe] and [Ba/Fe], and a strong positive correlation between [Mg/Ba] and galaxy velocity dispersion. These trends are consistent with the idea that more massive galaxies formed their stars on shorter timescales compared to less massive galaxies, and rule out several other proposed explanations for the observed super-solar [Mg/Fe] values in massive galaxies. In contrast, [Sr/Fe] {approx}0, with no strong variation across the sample. It is difficult to interpret the Sr trends without detailed chemical evolution models owing to the multiplicity of proposed nucleosynthetic sites for Sr.

  1. Hot sputtering of barium strontium titanate on nickel foils

    Science.gov (United States)

    Aygün, Seymen M.; Daniels, Patrick; Borland, William; Maria, Jon-Paul

    2008-04-01

    The relationships linking temperature and voltage dependent dielectric response, grain size, and thermal budget during synthesis are illustrated. In doing so, it was found that maximizing thermal budgets within experimental bounds leads to electrical properties comparable to the best literature reports irrespective of the processing technique or microstructure. The optimal film properties include a bulk transition temperature, a room temperature permittivity of 1800, a voltage tuning ratio of 10:1 at 450 kV/cm, and a loss tangent less than 1.5% at 450 kV/cm. The sample set illustrates the well-known relationship between permittivity and crystal dimension, and the onset of a transition temperature shifts at very fine grain sizes. A brick wall model incorporating a high permittivity grain and a low permittivity grain boundary is used to interpret the dielectric data. However, the data show that high permittivity and tunability values can be achieved at grain sizes or film thicknesses that many reports associate with dramatic reductions in the dielectric response. These differences are discussed in terms of crystal quality and maximum processing temperature. The results collectively suggest that scaling effects in ferroelectric thin films are in many cases the result of low thermal budgets and the consequently high degree of structural imperfection and are not from the existence of low permittivity phases at the dielectric-electrode interface.

  2. Characterization Micro/Nanostructures of Barium Strontium Titanate

    OpenAIRE

    Abdelhalim Elbasset; Farid Abdi; Taj-Dine Lamcharfi; Nor-Said Echatoui

    2016-01-01

    Structural characteristics of Ba0.0975S0.025TiO3 (BS0.025T) ceramics calcined at different temperatures at 800, 850 and 900°C for 4 hours hove been investigated. Results DRX showed that the change in the cell parameter along a axis (a) is more important than that along c axis and is accompanied by spacing of these parameters. In addition they indicate that the diminuation of symmetry is caused by the increase of the calcination temperature This trend towards the tetragonale phase was confir...

  3. Strontium and Barium In Early-Type Galaxies

    CERN Document Server

    Conroy, Charlie; Graves, Genevieve J

    2013-01-01

    The detailed abundance patterns of the stars within galaxies provide a unique window into the history of star formation (SF) at early times. Two widely used `chronometers' include the alpha and iron-peak elements, which are created on short and long timescales, respectively. These two clocks have been widely used to estimate SF timescales from moderate-resolution spectra of early-type galaxies. Elements formed via s-process neutron captures (e.g., Sr and Ba) comprise a third type of chronometer, as the site of the main s-process is believed to be intermediate and low-mass asymptotic giant branch stars. The [alpha/Ba] ratio in particular should provide a powerful new constraint on the SF histories of galaxies, in part because it is insensitive to the uncertain distribution of type Ia SNe detonation times and the overall Ia rate. Here we present new measurements of the abundance of Sr and Ba in nearby early-type galaxies by applying stellar population synthesis tools to high S/N optical spectra. We find a stron...

  4. Abnormal grain growth in undoped strontium and barium titanate

    Energy Technology Data Exchange (ETDEWEB)

    Baeurer, M., E-mail: m.baeurer@ikm.uka.de [Institut fuer Keramik im Maschinenbau, Universitaet Karlsruhe, Karlsruhe (Germany); Shih, S.-J.; Bishop, C. [Department of Materials, University of Oxford, Oxford (United Kingdom); Harmer, M.P. [Center for Advanced Materials and Nanotechnology, Lehigh University, Bethlehem, PA (United States); Cockayne, D. [Department of Materials, University of Oxford, Oxford (United Kingdom); Hoffmann, M.J. [Institut fuer Keramik im Maschinenbau, Universitaet Karlsruhe, Karlsruhe (Germany)

    2010-01-15

    Abnormal grain growth is a commonly observed phenomenon in perovskite materials. In order to study this phenomenon, grain growth experiments were conducted over a temperature range from 1425 to 1600 deg. C for the model system SrTiO{sub 3} to analyse the nucleation of abnormal grains and to identify the growth mechanism involved for normal and abnormal grains. Grain boundaries of normal and abnormal grains were investigated in quenched samples by high-resolution transmission electron microscopy and by energy-dispersive spectroscopy in a scanning transmission electron microscope. No amorphous film was observed at the grain boundaries for either normal or abnormal grains. Non-stoichiometry at the grain boundaries was identified as a possible reason for the differences in growth speed. The results are compared to the nucleation and growth of abnormal grains in BaTiO{sub 3}.

  5. Multicolour second harmonic generation by strontium barium niobate nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez, E Martin; Jaque, D; Sole, J Garcia [Departamento de Fisica de Materiales, C-IV, Universidad Autonoma de Madrid, C/ Francisco Tomas y Valiente 7, 28049, Madrid (Spain); Speghini, A [DiSTeMeV, Universita di Verona and INSTM, UdR Verona, Via della Pieve 70, I-37029 San Floriano (Italy); Piccinelli, F; Nodari, L; Bettinelli, M [Dipartimento Scientifico e Tecnologico, Universita di Verona and INSTM, UdR Verona, Ca Vignal, Strada Le Grazie 15, I-37134 Verona (Italy)

    2009-05-21

    Infrared to visible second harmonic generation (SHG) has been demonstrated from 40 nm Sr{sub 0.6}Ba{sub 0.4}Nb{sub 2}O{sub 6} nanoparticles in a broad spectral range of infrared fundamental wave excitation (800-1200 nm). The efficiency for SHG is compared with that obtained from powdered samples of larger crystallite sizes so that the mechanism leading to optical frequency conversion is discussed. The obtained results point out the possibility of using nonlinear nanoparticles for multifrequency optical imaging. (fast track communication)

  6. Caracterização estrutural, propriedades dielétricas e ferroelétricas de filmes finos de Estrôncio-Bário-Nióbio (SBN Structural characterization, dielectric and ferroelectric properties of Strontium Barium Niobate (SBN thin films

    Directory of Open Access Journals (Sweden)

    R. G. Mendes

    2001-06-01

    Full Text Available Filmes finos de niobato de estrôncio e bário (SBN na composição 75/25 (Sr0,75Ba0,25Nb2O 6 foram depositados sobre substratos de Pt/Si usando-se um método químico baseado na obtenção de uma resina polimérica a partir de diferentes soluções de íons. Os filmes foram cristalizados em temperaturas entre 500 °C e 700 °C usando-se tratamentos térmicos convencionais de 1 hora e rápidos de 60 segundos. A presença da fase ferroelétrica do SBN foi confirmada somente em filmes cristalizados em temperaturas superiores a 600 °C, enquanto que para os filmes tratados termicamente a 500 °C verificou-se a presença de outras fases como o SrNb2O6 e BaNb2O6 que não são ferroelétricas. Os parâmetros de rede da estrutura tetragonal do SBN foram calculados com base nos difratogramas de raios X para diferentes condições de cristalização e os valores obtidos concordam bem com aqueles obtidos para filmes de SBN, reportados na literatura, preparados por outros métodos. Os parâmetros ferroelétricos foram obtidos usando-se um circuito Sawyer-Tower à temperatura ambiente na freqüência de 100 Hz. Para os filmes cristalizados a 700 °C os valores de polarização remanescente (Pr e campo coercitivo (Ec foram respectivamente 18 miC/cm² e 180 kV/cm para tratamentos térmicos convencionais e 17 miC/cm² e 235 kV/cm para tratamentos térmicos rápidos.Strontium Barium Niobate (SBN thin films in the composition 75/25 (Sr0.75Ba0.25Nb2O 6 were deposited on Pt/Si substrates by a chemical method based in a polymeric resin obtained from different ion solutions. The films were crystallized in temperatures between 500 °C and 700 °C using a conventional furnace for 1 hour and using rapid thermal annealing (RTA for 60 seconds. The ferroelectric phase SBN was confirmed for films crystallized in temperatures above 600 ºC, films thermal treated at 500 ºC we noted the presence of other phases such as SrNb2O6 and BaNb2O6, which are not ferroelectrics. The

  7. Temperature dependence dielectric properties of modified barium titanate-PVB composites

    Science.gov (United States)

    Joshi, N. J.; Rakshit, P. B.; Grewal, G. S.; Shrinet, V.; Pratap, A.

    2013-06-01

    In this work, attempts are made to prepare ceramic polymer-composite followed by characterization of dielectric properties. The Barium Titanate ceramic powders are synthesized using the hydrothermal process. Silane treatment is carried out on Barium Titanate powder to increase its compatibility with polymer, followed with preparation of ceramic-polymer composite. Polyvinyl Butyral (PVB) is used as matrix for preparation of the composites and the concentration of Barium Titanate is increased from 60 to 90 wt%. Dielectric properties such as volume resistivity, dielectric constant, dissipation factor are evaluated. Results indicate that the dielectric constant and dissipation factor vary between 52 to 120 and 0.01 to 0.07; respectively as the relative ratio of polymer and silane modified Barium Titanate is varied. Specifically, at 90 wt% of silane modified Barium Titanate, the highest dielectric constant of 123 along with dissipation factor of 0.07 is obtained.

  8. Controlling barium sulfate

    Energy Technology Data Exchange (ETDEWEB)

    Greenley, R.

    Even though for several years success has been realized in controlling barium sulfate scale deposition in relatively shallow, low pressure oil wells--by squeezing an organic phosphonate scale inhibitor into the producing zone--barium sulfate scale depositon in deep, high pressure/high temperature wells usually meant an expensive workover operation. A case history of a deep (16,000 ft) well in St. Mary Parish, Louisiana, and the scale inhibitor squeeze operation are described. Based on the successful results obtained in treating this well, a generalized treating procedure for combating downhole scale deposition in high pressure/high temperature gas wells is presented. Formation squeezing with such an inhibitor represents a significant breakthrough for the oil and gas industry.

  9. Electrorheological behavior of rare earth-doped barium titanate suspensions

    Institute of Scientific and Technical Information of China (English)

    2002-01-01

    Doping Y, La, Ce into barium titanate is found to be able to improve its electrorheological (ER) effect in DC electrical field. The yield stress of a typical doped barium titanate/silicone oil suspension is approximately 3.2 -*7〗kPa at 3.5 -*7〗kV/mm, which is 10 times larger than that of pure barium titanate/silicone oil suspensions. The ER effect increases with the decrease of ionic radius of rare earth (RE) dopant when RE concentration remains constant, and the suspensions exhibit a relatively high shear stress when Y, La, Ce mole fractions are 15%, 10%~15%, and 5%, respectively. Dielectric measurements show that the suitable doping with RE element increases dielectric loss of barium titanate and causes very marked dielectric relaxation at low frequency. By measuring X-ray diffraction patterns of doped barium titanate, it is considered that the occurrence of lattice distortion or defects may be responsible for the change of dielectric properties which results in the improvement of ER effect of barium titanate in DC electrical field.

  10. 氯化钡除杂制取高纯氢氧化钡%Preparation of high purity barium hydroxide by impurity - removed barium chloride

    Institute of Scientific and Technical Information of China (English)

    翁贤芬; 毛逢银; 何琳; 李莉

    2009-01-01

    Removal technology of strontium and iron from crude barium chloride raw material were studied.Optimization of process conditions of strontium and iron removal were discussed.When crude barium chloride stiring and dissolving the mixture at 60 ℃ for 40 min,impurities of stromtium and calcuim can be removed and mass fraction of strontium in the obatined solid barium chloride was below 1×10-4.Then add oxydol (H2O2) at proportion of 100 g raw materials per 8 mL H2O2,and add active carbon and small quantity of sodium hydroxide.Finally,iron could be get rid of when pH was controlled below 10.Mass fraction of iron in barium hydroxide product was less than 1×10-5 when using the iron - removed barium chaloride as raw material.Therefore,purified barium chloride by this method can be used to produce purity barium hydroxide.%研究了粗氯化钡原料中锶和铁杂质的脱除工艺,探讨了脱除锶和铁的优化工艺条件.在粗氯化钡原料中加入去离子水,液固质量比为0.25: 1,在60 ℃下搅拌溶解40 min,可除去锶和钙杂质,所得氯化钡固体中锶质量分数低于1×10-4.在氯化钡溶液中加入双氧水,每100 g原料中加入双氧水8 mL,加入活性炭和少量氢氧化钠,控制pH低于10时,可除去铁杂质,用除铁后的氯化钡制取氢氧化钡,产品中铁质量分数低于1×10-5.用除杂后的氯化钡可制得高纯氢氧化钡.

  11. Solid solution barium–strontium chlorides with tunable ammonia desorption properties and superior storage capacity

    Energy Technology Data Exchange (ETDEWEB)

    Bialy, Agata [Amminex Emissions Technology A/S, Gladsaxevej 363, 2860 Soeborg (Denmark); Jensen, Peter B. [Department of Energy Conversion and Storage, Technical University of Denmark, Frederiksborgvej 399, DK-4000 Roskilde (Denmark); Center for Atomic-scale Materials Design, Department of Physics, Technical University of Denmark, Fysikvej 311, DK-2800 Kgs. Lyngby (Denmark); Blanchard, Didier [Department of Energy Conversion and Storage, Technical University of Denmark, Frederiksborgvej 399, DK-4000 Roskilde (Denmark); Vegge, Tejs, E-mail: teve@dtu.dk [Department of Energy Conversion and Storage, Technical University of Denmark, Frederiksborgvej 399, DK-4000 Roskilde (Denmark); Quaade, Ulrich J., E-mail: ujq@amminex.com [Amminex Emissions Technology A/S, Gladsaxevej 363, 2860 Soeborg (Denmark)

    2015-01-15

    Metal halide ammines are very attractive materials for ammonia absorption and storage—applications where the practically accessible or usable gravimetric and volumetric storage densities are of critical importance. Here we present, that by combining advanced computational materials prediction with spray drying and in situ thermogravimetric and structural characterization, we synthesize a range of new, stable barium-strontium chloride solid solutions with superior ammonia storage densities. By tuning the barium/strontium ratio, different crystallographic phases and compositions can be obtained with different ammonia ab- and desorption properties. In particular it is shown, that in the molar range of 35–50% barium and 65–50% strontium, stable materials can be produced with a practically usable ammonia density (both volumetric and gravimetric) that is higher than any of the pure metal halides, and with a practically accessible volumetric ammonia densities in excess of 99% of liquid ammonia. - Graphical abstract: Thermal desorption curves of ammonia from Ba{sub x}Sr{sub (1−x)}Cl{sub 2} mixtures with x equal to 0.125, 0.25 and 0.5 and atomic structure of Sr(NH{sub 3}){sub 8}Cl{sub 2}. - Highlights: • Solid solutions of strontium and barium chloride were synthesized by spray drying. • Adjusting molar ratios led to different crystallographic phases and compositions. • Different molar ratios led to different ammonia ab-/desorption properties. • 35–50 mol% BaCl{sub 2} in SrCl{sub 2} yields higher ammonia density than any other metal halide. • DFT calculations can be used to predict properties of the mixtures.

  12. Comparison of Barium and Arsenic Concentrations in Well Drinking Water and in Human Body Samples and a Novel Remediation System for These Elements in Well Drinking Water.

    Directory of Open Access Journals (Sweden)

    Masashi Kato

    Full Text Available Health risk for well drinking water is a worldwide problem. Our recent studies showed increased toxicity by exposure to barium alone (≤700 µg/L and coexposure to barium (137 µg/L and arsenic (225 µg/L. The present edition of WHO health-based guidelines for drinking water revised in 2011 has maintained the values of arsenic (10 µg/L and barium (700 µg/L, but not elements such as manganese, iron and zinc. Nevertheless, there have been very few studies on barium in drinking water and human samples. This study showed significant correlations between levels of arsenic and barium, but not its homologous elements (magnesium, calcium and strontium, in urine, toenail and hair samples obtained from residents of Jessore, Bangladesh. Significant correlation between levels of arsenic and barium in well drinking water and levels in human urine, toenail and hair samples were also observed. Based on these results, a high-performance and low-cost adsorbent composed of a hydrotalcite-like compound for barium and arsenic was developed. The adsorbent reduced levels of barium and arsenic from well water in Bangladesh and Vietnam to <7 µg/L within 1 min. Thus, we have showed levels of arsenic and barium in humans and propose a novel remediation system.

  13. Comparison of Barium and Arsenic Concentrations in Well Drinking Water and in Human Body Samples and a Novel Remediation System for These Elements in Well Drinking Water.

    Science.gov (United States)

    Kato, Masashi; Kumasaka, Mayuko Y; Ohnuma, Shoko; Furuta, Akio; Kato, Yoko; Shekhar, Hossain U; Kojima, Michiyo; Koike, Yasuko; Dinh Thang, Nguyen; Ohgami, Nobutaka; Ly, Thuy Bich; Jia, Xiaofang; Yetti, Husna; Naito, Hisao; Ichihara, Gaku; Yajima, Ichiro

    2013-01-01

    Health risk for well drinking water is a worldwide problem. Our recent studies showed increased toxicity by exposure to barium alone (≤700 µg/L) and coexposure to barium (137 µg/L) and arsenic (225 µg/L). The present edition of WHO health-based guidelines for drinking water revised in 2011 has maintained the values of arsenic (10 µg/L) and barium (700 µg/L), but not elements such as manganese, iron and zinc. Nevertheless, there have been very few studies on barium in drinking water and human samples. This study showed significant correlations between levels of arsenic and barium, but not its homologous elements (magnesium, calcium and strontium), in urine, toenail and hair samples obtained from residents of Jessore, Bangladesh. Significant correlation between levels of arsenic and barium in well drinking water and levels in human urine, toenail and hair samples were also observed. Based on these results, a high-performance and low-cost adsorbent composed of a hydrotalcite-like compound for barium and arsenic was developed. The adsorbent reduced levels of barium and arsenic from well water in Bangladesh and Vietnam to <7 µg/L within 1 min. Thus, we have showed levels of arsenic and barium in humans and propose a novel remediation system.

  14. On barium oxide solubility in barium-containing chloride melts

    Energy Technology Data Exchange (ETDEWEB)

    Nikolaeva, Elena V.; Zakiryanova, Irina D.; Bovet, Andrey L.; Korzun, Iraida V. [Ural Federal Univ., Yekaterinburg (Russian Federation). Inst. of High Temperature Electrochemistry

    2016-11-01

    Oxide solubility in chloride melts depends on temperature and composition of molten solvent. The solubility of barium oxide in the solvents with barium chloride content is essentially higher than that in molten alkali chlorides. Spectral data demonstrate the existence of oxychloride ionic groupings in such melts. This work presents the results of the BaO solubility in two molten BaCl{sub 2}-NaCl systems with different barium chloride content. The received data together with earlier published results revealed the main regularities of BaO solubility in molten BaO-BaCl{sub 2}-MCl systems.

  15. 复相陶瓷铌酸锶钡/钛酸锶钡介电常数预测模型研究%Dielectric Constants Theory Model for (1-x)BaO·xSrO·0.5Nb2Os·0.5TiO2 Composite Ceramics

    Institute of Scientific and Technical Information of China (English)

    单连伟; 王继华; 马成国; 吴泽; 董丽敏; 韩志东; 张显友

    2011-01-01

    (1-x)BaO · x SrO · 0.5Nb2O5· 0.5TiO2 composite ceramics were prepared through powder-sol(P-S) process. X-ray diffraction(XRD) reveals that the tetragonal tungsten bronze phase and the perovskite phase coexist in the ceramics. Based on the Clausius-Mosotti equation, a dielectric constants theory model of barium strontium titanate(BST)/ strontium barium niobate (SBN) was established by the theoretical polarizability of BST and SBN. The results show that the experimental test value of dielectric constants is consistent with the calculation value via the theory model.%采用粉末-溶胶工艺制备了铌酸锶钡/钛酸锶钡(SBN/BST)复相陶瓷.X射线衍射研究表明钨青铜相和钙钛矿相共存于体系中.以Clausius(克劳修斯)-Mosotti(莫索缔)方程为基础,采用混合对数法则、铌酸锶钡和钛酸锶钡的理论极化率建立了SBN/BST的介电常数预测模型.结果表明:通过介电常数预测模型得到的数值与实验测试值相吻合.

  16. Doped barium titanate nanoparticles

    Indian Academy of Sciences (India)

    T K Kundu; A Jana; P Barik

    2008-06-01

    We have synthesized nickel (Ni) and iron (Fe) ion doped BaTiO3 nanoparticles through a chemical route using polyvinyl alcohol (PVA). The concentration of dopant varies from 0 to 2 mole% in the specimens. The results from X-ray diffractograms and transmission electron micrographs show that the particle diameters in the specimen lie in the range 24–40 nm. It is seen that the dielectric permittivity in doped specimens is enhanced by an order of magnitude compared to undoped barium titanate ceramics. The dielectric permittivity shows maxima at 0.3 mole% doping of Fe ion and 0.6 mole% of Ni ion. The unusual dielectric behaviour of the specimens is explained in terms of the change in crystalline structure of the specimens.

  17. Barium titanate thick films prepared by screen printing technique

    Directory of Open Access Journals (Sweden)

    Mirjana M. Vijatović

    2010-06-01

    Full Text Available The barium titanate (BaTiO3 thick films were prepared by screen printing technique using powders obtained by soft chemical route, modified Pechini process. Three different barium titanate powders were prepared: i pure, ii doped with lanthanum and iii doped with antimony. Pastes for screen printing were prepared using previously obtained powders. The thick films were deposited onto Al2O3 substrates and fired at 850°C together with electrode material (silver/palladium in the moving belt furnace in the air atmosphere. Measurements of thickness and roughness of barium titanate thick films were performed. The electrical properties of thick films such as dielectric constant, dielectric losses, Curie temperature, hysteresis loop were reported. The influence of different factors on electrical properties values was analyzed.

  18. Studies of Bone Metabolism with the Aid of Radioactive Strontium

    Energy Technology Data Exchange (ETDEWEB)

    Jones, D.C.; Copp, D.H., M.D.

    1948-04-01

    The kinetics of skeletal uptake and urinary excretion of radiostrontium were studied during the critieal first hour following intraperitoneal injection of a carrier-free dose. These experiments not only provided valuable data con.cerning the metabolism and fixation of this important fission product, but, because of the close similarity of strontium and calcium, also gave basic information on the process of calcification. Three groups of rats were compared: normal mature adults, young growing normal animals, and young rachitic rats. In all groups, the blood radioactive strontium rose to a maximum in 10-15 minutes, and then declined as the strontium continued to deposit in the skeleton or to be excreted in the urine. Muscle and skin strontium curves followed those of blood quite closely, suggesting a rapid equilibrium between their extracellular fluid and blood plasma. In all groups there was a continous uptake of strontium by the skeleton. In the adults, this was almost constant, suggesting uptek e by absorption and exchange with the calcium of the bone mineral. In the young rats, both normal and rachitic, the very rapid initial rate of uptake of radio-strontium tapered off sharply with time, indicating that some of this radio-element was coming back from the bone into the blood stream. This suggested a rapid labile combination of strontiunl in these animals, which, since it also occured in the rachitic group in which normal calcification is inhibited, probably associated with the protein osteoid matrix present in both. A hypothetical calcification mechanism was suggested by these findings. Urinary excretion and renal clearance of strontium was constant in all three groups, but the clearance was almost ten times as great in the rachitic as in the normal young and adult rats. This would seem to indicate a direct effect of rickets on the renal mechanism of radiostrontium (and calcium) excretion.

  19. 无水氯化锶的制备工艺研究%Preparation Technology of Anhydrous Strontium Chloride

    Institute of Scientific and Technical Information of China (English)

    邹兴武; 王树轩; 杨占寿; 王舒娅; 祁米香

    2012-01-01

    依托青海锶资源优势,以次等品碳酸锶和工业盐酸为原料,制备了无水氯化锶.并对除钡、除铁、除硫、脱水干燥等工艺进行了研究.产品能达到一般工业品的要求.氯化锶的制备不仅丰富我省锶产品的种类,而且增加了锶资源企业的抗风险能力.%Relying on the advantage of Qinghai strontium resources, the anhydrous strontium chloride was prepared by low-grade strontium carbonate and industrial hydrochloric acid. The process of removal of barium, sulfur and other impurities from low-grade strontium carbonate was studied,and evaporation,concentration , crystallization, filtering and drying processes were also investigated. The quality of products can reach the requirements of the general industrial. Preparation of strontium chloride, not only enrich the types of strontium products in Qinghai province,but also increase the ability of resiting risk of Strontium production enterprises.

  20. Spectrographic determination of strontium in yttrium-90 solutions; Determinacion espectrografica de estroncio en soluciones de itrio-90

    Energy Technology Data Exchange (ETDEWEB)

    Roca, M.; Capdevila, C.

    1970-07-01

    The copper spark method has been used for determining strontium in the concentration range 1-100 g/ml in yttrium-90 solutions containing 0,5 % or thereabouts of ammonium citrate. The influence of the citric acid as well as the ammonium citrate with regard to 2N HCL solutions has been studied: the citric acid enhances the line intensities of strontium. The employment of either barium or lanthanum as reference element compensates for this enhancement. Because of the increase in sensitivity mentioned above, the study of influence of the citric acid has been extended and several impurities usually determined in radioisotope solutions have been considered. (Author) 4 refs.

  1. Dielectric behaviour of strontium tartrate single crystals

    Indian Academy of Sciences (India)

    S K Arora; Vipul Patel; Brijesh Amin; Anjana Kothari

    2004-04-01

    Strontium tartrate trihydrate (STT) crystals have been grown in silica hydrogel. Various polarization mechanisms such as atomic polarization of lattice, orientational polarization of dipoles and space charge polarization in the grown crystals have been understood using results of the measurements of dielectric constant (') and dielectric loss (tan ) as functions of frequency and temperature. Ion core type polarization is seen in the temperature range 75–180°C, and above 180°C, there is interfacial polarization for relatively lower frequency range. One observes dielectric dispersion at lower frequency presumably due to domain wall relaxation.

  2. Interferometry with Strontium Ions

    Science.gov (United States)

    Jackson, Jarom; Lambert, Enoch; Otterstrom, Nils; Jones, Tyler; Durfee, Dallin

    2014-05-01

    We describe progress on a cold ion matter-wave interferometer. Cold Strontium atoms are extracted from an LVIS. The atoms will be photo-ionized with a two-photon transition to an auto-ionizing state in the continuum. The ions will be split and recombined using stimulated Raman transitions from a pair of diode lasers injection locked to two beams from a master laser which have been shifted up and down by half the hyperfine splitting. We are developing laser instrumentation for this project including a method to prevent mode-hopping by analyzing laser frequency noise, and an inexpensive, robust wavelength meter. Supported by NSF Award No. 1205736.

  3. 75 FR 33824 - Barium Chloride From China

    Science.gov (United States)

    2010-06-15

    ... COMMISSION Barium Chloride From China Determination On the basis of the record\\1\\ developed in the subject... order on barium chloride from China would be likely to lead to continuation or recurrence of material... Barium Chloride from China: Investigation No. 731-TA-149 (Third Review). By order of the...

  4. The crystal growth of barium flouride in aqueous solution

    Science.gov (United States)

    Barone, J. P.; Svrjcek, D.; Nancollas, G. H.

    1983-06-01

    The kinetics of growth of barium flouride seed crystals were investigated in aqueous solution at 25°C using a constant composition method, in which the supersaturation and ionic strength were maintained constant by the addition of titrants consisting of barium nitrate and potassium flouride solutions. The rates of reaction, studied over a range of supersaturation (σ ≈ 0.4 to 1.0), were interpreted in terms of crystal growth models. A spiral growth mechanism best describes the data, and scanning electron microscopy indicates a three-dimensional growth. In the presence of inorganic additives such as phosphate, however, induction periods precede a morphological two-dimensional crystallization. Coulter Counter results show little crystal agglomeration.

  5. MR Colonography with fecal tagging: Barium vs. barium ferumoxsil

    DEFF Research Database (Denmark)

    Achiam, M.P.; Chabanova, E.; Logager, V.B.

    2008-01-01

    qualitatively (with the standard method using contrast-to-wall ratio) and subjectively (using a visual analog scale [VAS]) by three different blinded observers. Results. Evaluated both qualitatively and subjectively, the tagging efficiency of barium sulfate/ferumoxsil was significantly better (P

  6. Rapid determination of strontium-90 by solid phase extraction using DGA Resin® for seawater monitoring

    Science.gov (United States)

    Tazoe, H.; Obata, H.; Yamagata, T.; Karube, Z.; Yamada, M.

    2015-12-01

    Strontium-90 concentrations in seawater exceeding the background level have been observed at the accidents of nuclear facilities, such as Chernobyl and Fukushima. However, analytical procedure for strontium-90 in seawater is still quite complicated and challenging. Here we show a simple and rapid analytical technique for the determination of strontium-90 in seawater samples without time-consuming separation of strontium from calcium. The separation with DGA Resin® is used to determine the abundance of strontium-90, which selectively collects yttrium-90, progeny of strontium-90. Naturally occurring radioactive nuclides (such as potassium, lead, bismuth, uranium, and thorium) and anthropogenic radionuclides (such as cesium, barium, lanthanum, and cerium) were separated from yttrium. Through a sample separation procedure, a high chemical yield of yttrium-90 was achieved at 93.9 % for seawater. The result of IAEA 443 certified seawater analysis was in good agreement with the certified value. At 20 hrs counting a lower detection limit of 1.5 mBq L-1 was obtained from 3 L of seawater. The proposed method can finish analyzing 8 samples per day, which is a reasonably fast throughput in actual seawater monitoring. Reproducibility was found to be 3.4 % according to 10 separate analyses of natural seawater samples from the vicinity of Fukushima Daiichi Nuclear Power Plant in September 2013.

  7. Carbon and Strontium Abundances of Metal-Poor Stars

    CERN Document Server

    Lai, David K; Bolte, Michael; Lucatello, Sara

    2007-01-01

    We present carbon and strontium abundances for 100 metal-poor stars measured from R$\\sim $7000 spectra obtained with the Echellette Spectrograph and Imager at the Keck Observatory. Using spectral synthesis of the G-band region, we have derived carbon abundances for stars ranging from [Fe/H]$=-1.3$ to [Fe/H]$=-3.8$. The formal errors are $\\sim 0.2$ dex in [C/Fe]. The strontium abundance in these stars was measured using spectral synthesis of the resonance line at 4215 {\\AA}. Using these two abundance measurments along with the barium abundances from our previous study of these stars, we show it is possible to identify neutron-capture-rich stars with our spectra. We find, as in other studies, a large scatter in [C/Fe] below [Fe/H]$ = -2$. Of the stars with [Fe/H]$<-2$, 9$\\pm$4% can be classified as carbon-rich metal-poor stars. The Sr and Ba abundances show that three of the carbon-rich stars are neutron-capture-rich, while two have normal Ba and Sr. This fraction of carbon enhanced stars is consistent with ...

  8. Sintered bentonite ceramics for the immobilization of cesium- and strontium-bearing radioactive waste

    Science.gov (United States)

    Ortega, Luis Humberto

    The Advanced Fuel Cycle Initiative (AFCI) is a Department of Energy (DOE) program, that has been investigating technologies to improve fuel cycle sustainability and proliferation resistance. One of the program's goals is to reduce the amount of radioactive waste requiring repository disposal. Cesium and strontium are two primary heat sources during the first 300 years of spent nuclear fuel's decay, specifically isotopes Cs-137 and Sr-90. Removal of these isotopes from spent nuclear fuel will reduce the activity of the bulk spent fuel, reducing the heat given off by the waste. Once the cesium and strontium are separated from the bulk of the spent nuclear fuel, the isotopes must be immobilized. This study is focused on a method to immobilize a cesium- and strontium-bearing radioactive liquid waste stream. While there are various schemes to remove these isotopes from spent fuel, this study has focused on a nitric acid based liquid waste. The waste liquid was mixed with the bentonite, dried then sintered. To be effective sintering temperatures from 1100 to 1200°C were required, and waste concentrations must be at least 25 wt%. The product is a leach resistant ceramic solid with the waste elements embedded within alumino-silicates and a silicon rich phase. The cesium is primarily incorporated into pollucite and the strontium into a monoclinic feldspar. The simulated waste was prepared from nitrate salts of stable ions. These ions were limited to cesium, strontium, barium and rubidium. Barium and rubidium will be co-extracted during separation due to similar chemical properties to cesium and strontium. The waste liquid was added to the bentonite clay incrementally with drying steps between each addition. The dry powder was pressed and then sintered at various temperatures. The maximum loading tested is 32 wt. percent waste, which refers to 13.9 wt. percent cesium, 12.2 wt. percent barium, 4.1 wt. percent strontium, and 2.0 wt. percent rubidium. Lower loadings of waste

  9. Barium titanate nanoparticles: promising multitasking vectors in nanomedicine

    Science.gov (United States)

    Graziana Genchi, Giada; Marino, Attilio; Rocca, Antonella; Mattoli, Virgilio; Ciofani, Gianni

    2016-06-01

    Ceramic materials based on perovskite-like oxides have traditionally been the object of intense interest for their applicability in electrical and electronic devices. Due to its high dielectric constant and piezoelectric features, barium titanate (BaTiO3) is probably one of the most studied compounds of this family. Recently, an increasing number of studies have been focused on the exploitation of barium titanate nanoparticles (BTNPs) in the biomedical field, owing to the high biocompatibility of BTNPs and their peculiar non-linear optical properties that have encouraged their use as nanocarriers for drug delivery and as label-free imaging probes. In this review, we summarize all the recent findings about these ‘smart’ nanoparticles, including the latest, most promising potential as nanotransducers for cell stimulation.

  10. Strontium Carbonate Industry Needs Urgent Upgrade

    Institute of Scientific and Technical Information of China (English)

    Jin Tianxin

    2007-01-01

    @@ Strontium carbonate is an important inorganic chemical product mainly used in the manufacture of magnetic materials such as glass shell for picture tubes,cathode-ray tubes (CRT) for color TVs,electromagnets and strontium ferrite.

  11. Physical states and properties of barium titanate films in a plane electric field

    Science.gov (United States)

    Shirokov, V. B.; Kalinchuk, V. V.; Shakhovoi, R. A.; Yuzyuk, Yu. I.

    2016-07-01

    The influence of a plane electric field on the phase states of barium titanate thin films under the conditions of forced deformation has been studied. The field dependence of a complete set of material constants has been taken in the region of the c-phase, where polarization losses are absent. The material constants are calculated using equations of the piezoelectric effect derived by linearizing the nonlinear equations of state from the phenomenological; theory for barium titanate. It has been shown that there is a critical value of the field at which the electromechanical coupling coefficient reaches a maximum.

  12. Strontium ranelate improved tooth anchorage and reduced root resorption in orthodontic treatment of rats.

    Science.gov (United States)

    Kirschneck, Christian; Wolf, Michael; Reicheneder, Claudia; Wahlmann, Ulrich; Proff, Peter; Roemer, Piero

    2014-12-05

    The anchorage mechanisms currently used in orthodontic treatment have various disadvantages. The objective of this study was to determine the applicability of the osteoporosis medication strontium ranelate in pharmacologically induced orthodontic tooth anchorage. In 48 male Wistar rats, a constant orthodontic force of 0.25 N was reciprocally applied to the upper first molar and the incisors by means of a Sentalloy(®) closed coil spring for two to four weeks. 50% of the animals received strontium ranelate at a daily oral dosage of 900 mg per kilogramme of body weight. Bioavailability was determined by blood analyses. The extent of tooth movement was measured both optometrically and cephalometrically (CBCT). Relative alveolar gene expression of osteoclastic markers and OPG-RANKL was assessed by qRT-PCR and root resorption area and osteoclastic activity were determined in TRAP-stained histologic sections of the alveolar process. Compared to controls, the animals treated with strontium ranelate showed up to 40% less tooth movement after four weeks of orthodontic treatment. Gene expression and histologic analyses showed significantly less osteoclastic activity and a significantly smaller root resorption area. Blood analyses confirmed sufficient bioavailability of strontium ranelate. Because of its pharmacologic effects on bone metabolism, strontium ranelate significantly reduced tooth movement and root resorption in orthodontic treatment of rats. Strontium ranelate may be a viable agent for inducing tooth anchorage and reducing undesired root resorption in orthodontic treatment. Patients under medication of strontium ranelate have to expect prolonged orthodontic treatment times.

  13. Photostriction of strontium ruthenate

    KAUST Repository

    Wei, Tzu-Chiao

    2017-04-24

    Transition metal oxides with a perovskite crystal structure exhibit a variety of physical properties associated with the lattice. Among these materials, strontium ruthenate (SrRuO3) displays unusually strong coupling of charge, spin and lattice degrees of freedom that can give rise to the photostriction, that is, changes in the dimensions of material due to the absorption of light. In this study, we observe a photon-induced strain as high as 1.12% in single domain SrRuO3, which we attribute to a nonequilibrium of phonons that are a result of the strong interaction between the crystalline lattice and electrons excited by light. In addition, these light-induced changes in the SrRuO3 lattice affect its electrical resistance. The observation of both photostriction and photoresistance in SrRuO3 suggests the possibility of utilizing the mechanical and optical functionalities of the material for next-generation optoelectronics, such as remote switches, light-controlled elastic micromotors, microactuators and other optomechanical systems.

  14. Polymeric strontium ranelate nonahydrate

    Directory of Open Access Journals (Sweden)

    Kenny Stahl

    2011-04-01

    Full Text Available The title compound, poly[[μ-aqua-tetraaqua{μ-5-[bis(carboxylatomethylamino]-3-carboxylatomethyl-4-cyanothiophene-2-carboxylato}distrontium(II] tetrahydrate], [Sr2(C12H6N2O8S(H2O5]·3.79H2O, crystallizes with nine- and eight-coordinated Sr2+ cations. They are bound to seven of the eight ranelate O atoms and five of the water molecules. The SrO8 and SrO9 polyhedra are interconnected by edge-sharing, forming hollow layers parallel to (011. The layers are, in turn, interconnected by ranelate anions, forming a metal–organic framework (MOF structure with channels along the a axis. The four water molecules not coordinated to strontium are located in these channels and hydrogen bonded to each other and to the ranelates. Part of the water H atoms are disordered. The compound dehydrates very easily and 0.210 (4 water molecules out of nine were lost during crystal mounting causing additional disorder in the water structure.

  15. Multiwavelength Strontium Vapor Lasers

    Science.gov (United States)

    Soldatov, A. N.; Yudin, N. A.

    2016-08-01

    Based on an analysis of experimental and theoretical works, modern notion on conditions of forming of population density inversion on self-terminating IR transitions of alkali-earth metals is given. It is demonstrated that there is a significant difference in the inversion formation in lasers on self-terminating transitions in the visible and near-IR ranges and lasers on self-terminating transitions of alkali-earth metals lasing IR lines in the mid-IR range. It is shown that in the discharge circuit of lasers on self-terminating metal atom transitions (LSMT) there are processes strengthening the influence of the known mechanism limiting the frequency and energy characteristics (FEC) of radiation caused by the presence of prepulse electron concentration. The mechanism of influence of these processes on FEC of the LSMT and technical methods of their neutralization are considered. The possibility of obtaining average lasing power of ~200 W from one liter volume of the active medium of the strontium vapor laser is demonstrated under conditions of neutralization of these processes.

  16. Surface complexation model for strontium sorption to amorphous silica and goethite

    Directory of Open Access Journals (Sweden)

    Criscenti Louise J

    2008-01-01

    Full Text Available Abstract Strontium sorption to amorphous silica and goethite was measured as a function of pH and dissolved strontium and carbonate concentrations at 25°C. Strontium sorption gradually increases from 0 to 100% from pH 6 to 10 for both phases and requires multiple outer-sphere surface complexes to fit the data. All data are modeled using the triple layer model and the site-occupancy standard state; unless stated otherwise all strontium complexes are mononuclear. Strontium sorption to amorphous silica in the presence and absence of dissolved carbonate can be fit with tetradentate Sr2+ and SrOH+ complexes on the β-plane and a monodentate Sr2+complex on the diffuse plane to account for strontium sorption at low ionic strength. Strontium sorption to goethite in the absence of dissolved carbonate can be fit with monodentate and tetradentate SrOH+ complexes and a tetradentate binuclear Sr2+ species on the β-plane. The binuclear complex is needed to account for enhanced sorption at hgh strontium surface loadings. In the presence of dissolved carbonate additional monodentate Sr2+ and SrOH+ carbonate surface complexes on the β-plane are needed to fit strontium sorption to goethite. Modeling strontium sorption as outer-sphere complexes is consistent with quantitative analysis of extended X-ray absorption fine structure (EXAFS on selected sorption samples that show a single first shell of oxygen atoms around strontium indicating hydrated surface complexes at the amorphous silica and goethite surfaces. Strontium surface complexation equilibrium constants determined in this study combined with other alkaline earth surface complexation constants are used to recalibrate a predictive model based on Born solvation and crystal-chemistry theory. The model is accurate to about 0.7 log K units. More studies are needed to determine the dependence of alkaline earth sorption on ionic strength and dissolved carbonate and sulfate concentrations for the development of

  17. Barium aspiration and alveolarisation of barium in an infant: A case report and review of management

    Directory of Open Access Journals (Sweden)

    Alan F. Isles

    2014-05-01

    Full Text Available We describe a case of bilateral inhalation and alveolarisation of barium in an infant following a barium swallow for investigation of dusky spells associated with feeds. A bronchoscopy subsequently revealed the presence of a mid-tracheal tracheo-oesophageal cleft. We review the literature on barium aspiration, its consequences and make recommendations for management.

  18. INFLUENCE OF BARIUM OXIDE ADDITIONS ON PORTLAND CLINKER

    National Research Council Canada - National Science Library

    Zezulova, Anezka

    2016-01-01

    ... that the radiation shielding capability of cement can be improved by incorporation of barium. This work deals with the influence of barium oxide, added in the form of barium carbonate and sulphate, on the formation and properties of Portland clinker...

  19. ONE CASE REPORT OF ACUTE POISONING BY BARIUM CARBONATE

    Institute of Scientific and Technical Information of China (English)

    GE Qin-min; BIAN Fan; WANG Shu-yun; SHEN Sheng-hui

    2009-01-01

    @@ Most barium poisoning cases were caused by oral intake by mistake. Recent years, barium carbonate poisoning has been rare to be reported. Here we reported a case of acute barium carbonate toxication taken orally on purpose.

  20. Optical planar waveguide in sodium-doped calcium barium niobate crystals by carbon ion implantation

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Jin-Hua, E-mail: zhaojinhuazjh@gmail.com [School of Science, Shandong Jianzhu University, Jinan 250101 (China); Qin, Xi-Feng; Wang, Feng-Xiang; Fu, Gang; Wang, Hui-Lin [School of Science, Shandong Jianzhu University, Jinan 250101 (China); Wang, Xue-Lin [School of Physics, Key Laboratory of Particle Physics and Particle Irradiation, Ministry of Education, and State Key Laboratory of Crystal Materials, Shandong University, Jinan 250100 (China)

    2013-07-15

    There is great interest in niobate crystals which belong to the tetragonal tungsten bronze (TTB) families owing to their intriguing properties. As one representative of such crystals, CBN (calcium barium niobate) has attracted rapidly growing attention. Because it has a higher Curie temperature than SBN (strontium barium niobate), possesses outstanding ferroelectric and it possesses optical properties. In addition, doped with sodium, CBN will show a higher Curie temperature than pure CBN. We report on the fabrication and characterization of optical planar waveguide in x-cut sodium-doped calcium barium niobate crystal by using C ion implantation. The guided-mode properties at the wavelength of 633 and 1539 nm are investigated through prism-coupling measurements, respectively. By applying direct end-face coupling arrangement, the near-field optical intensity distribution of waveguide modes is measured at 633 nm. For comparison, the modal profile of the same guided mode is also numerically calculated by the finite difference beam-propagation method via computer software BeamPROP. The transmission spectra of the waveguide before and after ion implantation treatments were investigated also. Our experiment results reveal that the waveguide could propagate light with transverse magnetic polarized direction only and it is assumed that the polarization selectivity of CBN crystal may responsible for this phenomenon.

  1. 75 FR 19657 - Barium Chloride From China

    Science.gov (United States)

    2010-04-15

    ... COMMISSION Barium Chloride From China AGENCY: United States International Trade Commission. ACTION: Notice of... chloride from China. SUMMARY: The Commission hereby gives notice that it will proceed with a full review... revocation of the antidumping duty order on barium chloride from China would be likely to lead...

  2. Laser cooling and trapping of barium

    NARCIS (Netherlands)

    De, Subhadeep

    2008-01-01

    Laser cooling and trapping of heavy alkaline-earth element barium have been demonstrated for the first time ever. For any possible cycling transition in barium that could provide strong cooling forces, the excited state has a very large branching probability to metastable states. Additional lasers

  3. Laser cooling and trapping of barium

    NARCIS (Netherlands)

    De, Subhadeep

    2008-01-01

    Laser cooling and trapping of heavy alkaline-earth element barium have been demonstrated for the first time ever. For any possible cycling transition in barium that could provide strong cooling forces, the excited state has a very large branching probability to metastable states. Additional lasers a

  4. Spectroscopic (multi-energy) CT distinguishes iodine and barium contrast material in MICE

    Energy Technology Data Exchange (ETDEWEB)

    Anderson, N.G. [University of Otago, Department of Radiology, Christchurch (New Zealand); Butler, A.P. [University of Otago, Department of Radiology, Christchurch (New Zealand); University of Canterbury, Physics and Astronomy, Christchurch (New Zealand); Scott, N.J.A. [University of Otago, Department of Medicine, Christchurch (New Zealand); Cook, N.J. [Christchurch Hospital, Medical Physics and Bioengineering, Christchurch (New Zealand); Butzer, J.S. [Karlsruhe Institute of Technology, Physics Department, Karlsruhe (Germany); Schleich, N. [University of Canterbury, Physics and Astronomy, Christchurch (New Zealand); Christchurch Hospital, Medical Physics and Bioengineering, Christchurch (New Zealand); Firsching, M. [Friedrich Alexander University, Physics Department, Erlangen (Germany); Grasset, R.; Ruiter, N. de [University of Canterbury, Hitlab NZ, Christchurch (New Zealand); Campbell, M. [European Organisation for Nuclear Research, Physics Section, Geneva (Switzerland); Butler, P.H. [University of Canterbury, Physics and Astronomy, Christchurch (New Zealand)

    2010-09-15

    Spectral CT differs from dual-energy CT by using a conventional X-ray tube and a photon-counting detector. We wished to produce 3D spectroscopic images of mice that distinguished calcium, iodine and barium. We developed a desktop spectral CT, dubbed MARS, based around the Medipix2 photon-counting energy-discriminating detector. The single conventional X-ray tube operated at constant voltage (75 kVp) and constant current (150 {mu}A). We anaesthetised with ketamine six black mice (C57BL/6). We introduced iodinated contrast material and barium sulphate into the vascular system, alimentary tract and respiratory tract as we euthanised them. The mice were preserved in resin and imaged at four detector energy levels from 12 keV to 42 keV to include the K-edges of iodine (33.0 keV) and barium (37.4 keV). Principal component analysis was applied to reconstructed images to identify components with independent energy response, then displayed in 2D and 3D. Iodinated and barium contrast material was spectrally distinct from soft tissue and bone in all six mice. Calcium, iodine and barium were displayed as separate channels on 3D colour images at <55 {mu}m isotropic voxels. Spectral CT distinguishes contrast agents with K-edges only 4 keV apart. Multi-contrast imaging and molecular CT are potential future applications. (orig.)

  5. Ion-pair formation in aqueous strontium chloride and strontium hydroxide solutions under hydrothermal conditions by AC conductivity measurements.

    Science.gov (United States)

    Arcis, H; Zimmerman, G H; Tremaine, P R

    2014-09-01

    Frequency-dependent electrical conductivities of solutions of aqueous strontium hydroxide and strontium chloride have been measured from T = 295 K to T = 625 K at p = 20 MPa, over a very wide range of ionic strength (3 × 10(-5) to 0.2 mol kg(-1)), using a high-precision flow AC conductivity instrument. Experimental values for the concentration-dependent equivalent conductivity, Λ, of the two electrolytes were fitted with the Turq-Blum-Bernard-Kunz ("TBBK") ionic conductivity model, to determine ionic association constants, K(A,m). The TBBK fits yielded statistically significant formation constants for the species SrOH(+) and SrCl(+) at all temperatures, and for Sr(OH)2(0) and SrCl2(0) at temperatures above 446 K. The first and second stepwise association constants for the ion pairs followed the order K(A1)(SrOH(+)) > K(A1)(SrCl(+)) > K(A2)[Sr(OH)2(0)] > K(A2)[SrCl2(0)], consistent with long-range solvent polarization effects associated with the lower static dielectric constant and high compressibility of water at elevated temperatures. The stepwise association constants to form SrCl(+) agree with previously reported values for CaCl(+) to within the combined experimental error at high temperatures and, at temperatures below ∼375 K, the values of log10 KA1 for strontium are lower than those for calcium by up to ∼0.3-0.4 units. The association constants for the species SrOH(+) and Sr(OH)2(0) are the first accurate values to be reported for hydroxide ion pairs with any divalent cation under these conditions.

  6. Performance evaluation of 24 ion exchange materials for removing cesium and strontium from actual and simulated N-Reactor storage basin water

    Energy Technology Data Exchange (ETDEWEB)

    Brown, G.N.; Carson, K.J.; DesChane, J.R.; Elovich, R.J.

    1997-09-01

    This report describes the evaluation of 24 organic and inorganic ion exchange materials for removing cesium and strontium from actual and simulated waters from the 100 Area 105 N-Reactor fuel storage basin. The data described in this report can be applied for developing and evaluating ion exchange pre-treatment process flowsheets. Cesium and strontium batch distribution ratios (K{sub d}`s), decontamination factors (DF), and material loadings (mmol g{sup -1}) are compared as a function of ion exchange material and initial cesium concentration. The actual and simulated N-Basin waters contain relatively low levels of aluminum, barium, calcium, potassium, and magnesium (ranging from 8.33E-04 to 6.40E-05 M), with slightly higher levels of boron (6.63E-03 M) and sodium (1.62E-03 M). The {sup 137}Cs level is 1.74E-06 Ci L-{sup 1} which corresponds to approximately 4.87E-10 M Cs. The initial Na/Cs ratio was 3.33E+06. The concentration of total strontium is 4.45E-06 M, while the {sup 90}Sr radioactive component was measured to be 6.13E-06 Ci L{sup -1}. Simulant tests were conducted by contacting 0.067 g or each ion exchange material with approximately 100 mL of either the actual or simulated N-Basin water. The simulants contained variable initial cesium concentrations ranging from 1.00E-04 to 2.57E- 10 M Cs while all other components were held constant. For all materials, the average cesium K{sub d} was independent of cesium concentration below approximately 1.0E-06 M. Above this level, the average cesium K{sub d} values decreased significantly. Cesium K{sub d} values exceeding 1.0E+07 mL g{sup -1} were measured in the simulated N-Basin water. However, when measured in the actual N-Basin water the values were several orders of magnitude lower, with a maximum of 1.24E+05 mL g{sup -1} observed.

  7. Study on the Structure and Dielectric Properties of ZnO and Nb 2 O 5 Co-doped Barium Strontium Titanate Ceramics%ZnO和Nb2O5共掺杂钛酸锶钡陶瓷的结构及其介电性能研究

    Institute of Scientific and Technical Information of China (English)

    王俊岭; 周恒为; 马晓娇; 丁捷; 徐凡华; 衡晓; 雷婷; 尹红梅

    2014-01-01

    ZnO and Nb2O5 co-doped Ba0.2Sr0.8TiO3 ceramics were prepared by the method of solid state reaction. Crystalline structures and complex dielectric constant were measured by X-ray diffraction and dielectric spectra, respectively. The results show that:1) Zinc ions (Zn2+) and Niobium ion (Nb5+) enter the crystal lattice of Ba0.2Sr0.8TiO3 perovskite, and the ceramics have pure structure; 2) with the increase of Nb2O5 contents, the typical dispersion phase transition turns into the relaxation phase transition at low temperature, and a new relaxation processes has been found in the range of 300K-360K; 3) when doped certain amount of ZnO, the dielectric constant decreases and the dielectric loss increases at room temperature with the increasing of Nb 2 O 5 content.%采用固相反应法制备了ZnO、Nb 2 O 5共掺杂Ba 0.2 Sr 0.8 TiO 3陶瓷材料,并用X射线衍射(XRD)和介电谱方法,分别对系列陶瓷样品的结构和复介电常数进行了测量.结果表明:1)Zn2+、Nb5+进入Ba 0.2 Sr 0.8 TiO 3晶格后仍然为钙钛矿型固溶体;2)Nb 2 O 5会使得材料的低温弥散相变过程转变为弛豫相变过程,并在300~360K区域内会出现新的弛豫过程;3)掺入一定量的ZnO后Nb2O5掺入降低了Ba 0.2 Sr 0.8 TiO 3陶瓷材料的介电常数,增大了其介电损耗.

  8. Dielectric properties of piezoelectric 3–0 composites of lithium ferrite/barium titanate

    Indian Academy of Sciences (India)

    P Sarah; S V Suryanarayana

    2003-12-01

    Piezoelectric 3–0 composite ceramics are prepared from a mixture of barium titanate and lithium ferrite phase constituents. Dielectric properties of composites are affected by a number of parameters that include electrical properties, size, shape and amount of constituent phases. The frequency dependent measurements can provide additional insight into mechanisms controlling electrical response. Frequency dependence of dielectric constant plots of lithium ferrite/barium titanate composites will be given and the relevance of trends seen in them will be discussed. Connectivity in composites developed is studied.

  9. Sorption of strontium on clinoptilolite and heulandite

    Energy Technology Data Exchange (ETDEWEB)

    Chernyavskaya, N.B.

    1986-05-01

    The author investigates the sorption of strontium on the isostructural zeolites clinoptilolite and heulandite. In the Sr/Na/zeolite/H/sub 2/O system, clinoptilolite manifests selectivity for strontium, and heulandite for sodium. The role of the nature of the exchange ions is discussed. Modification of the clinoptilolite with acid, subsequently obtaining the Na, NH/sub 4/, or N/sub 2/H/sub 4/ form, increases the capacity for strontium by a factor of 2-4.

  10. Radium/Barium Waste Project

    Energy Technology Data Exchange (ETDEWEB)

    McDowell, Allen K.; Ellefson, Mark D.; McDonald, Kent M.

    2015-06-25

    The treatment, shipping, and disposal of a highly radioactive radium/barium waste stream have presented a complex set of challenges requiring several years of effort. The project illustrates the difficulty and high cost of managing even small quantities of highly radioactive Resource Conservation and Recovery Act (RCRA)-regulated waste. Pacific Northwest National Laboratory (PNNL) research activities produced a Type B quantity of radium chloride low-level mixed waste (LLMW) in a number of small vials in a facility hot cell. The resulting waste management project involved a mock-up RCRA stabilization treatment, a failed in-cell treatment, a second, alternative RCRA treatment approach, coordinated regulatory variances and authorizations, alternative transportation authorizations, additional disposal facility approvals, and a final radiological stabilization process.

  11. Magneto optical trapping of Barium

    CERN Document Server

    De, S; Jungmann, K; Willmann, L

    2008-01-01

    First laser cooling and trapping of the heavy alkaline earth element barium has been achieved based on the strong 6s$^2$ $^1$S$_0$ - 6s6p $^1$P$_1$ transition for the main cooling. Due to the large branching into metastable D-states several additional laser driven transitions are required to provide a closed cooling cycle. A total efficiency of $0.4(1) \\cdot 10^{-2}$ for slowing a thermal atomic beam and capturing atoms into a magneto optical trap was obtained. Trapping lifetimes of more than 1.5 s were observed. This lifetime is shortened at high laser intensities by photo ionization losses. The developed techniques will allow to extend significantly the number of elements that can be optically cooled and trapped.

  12. Effects of barium on the nonlinear electrical characteristics and dielectric properties of SnO2-based varistors

    Institute of Scientific and Technical Information of China (English)

    Wang Chun-Ming; Wang Jin-Feng; Wang Chun-Lei; Chen Hong-Cun; Su Wen-Bin; Zang Guo-Zhong; Qi Peng; Zhao Ming-Lei; Ming Bao-Quan

    2004-01-01

    The effects of barium on electrical and dielectric properties of the SnO2·Co2Oa.Ta2O5 varistor system sintered at 1250℃ for 60min were investigated. It is found that barium significantly improves the nonlinear properties. The breakdown electrical field increases from 378.0 to 2834.5V/mm, relative dielectric constant (at 1kHz) falls from 1206 to 161 and the resistivity (at 1kHz) rises from 60.3 to 1146.5kΩ·cm with an increase of BaCO3 concentration from 0mol%to 1.00mol%. The sample with 1.00mol% barium has the best nonlinear electrical property and the highest nonlinear coefficient (α=29.2). A modified defect barrier model is introduced to illustrate the grain-boundary barrier formation of barium-doped SnO2-based varistors.

  13. The review of various synthesis methods of barium titanate with the enhanced dielectric properties

    Energy Technology Data Exchange (ETDEWEB)

    More, S. P., E-mail: smitalomte@gmail.com [MIT college of Engineering, Aurangabad (MS) India (India); Topare, R. J., E-mail: r-topare@yahoo.com [Yogeshwari Mahavidyalaya, Ambajogai (MS) India (India)

    2016-05-06

    The Barium Titanate is a very well known dielectric ceramic belongs to perovskite structure. It has very wide applications in the field of electronic, electro ceramic, electromechanical and electro-optical applications. Barium Titanate has very high dielectric constant as well as low dielectric loss. Substituted dielectrics are one of the most important technological compounds in modern electro ceramics. Its electrical properties can be tuned flexibly by a simple substitution technique. This has encouraged researchers to select a typical cation to be substituted at cationic sites. In the present paper, the review of various synthesis methods of Barium Titanate compound with the effect of different dopants, the grain size on the dielectric properties at various temperatures is discussed.

  14. Optimization of a Strontium Aluminate

    Energy Technology Data Exchange (ETDEWEB)

    Bone, Alexandria N. [Maryville College, TN (United States)

    2017-08-01

    Strontium aluminate with Eu2+ and Dy3+ has been at the forefront of emerging applications for storage phosphors since its discovery in 1996. In this study, the emission intensity and luminescence lifetime of SrAl2O4: Eu2+, Dy3+ were enhanced by partial substitution of Ca2+ into Sr2+ sites in the matrix.

  15. Infrared Spectroscopic, X-ray and Nanoscale Characterization of Strontium Titanate Thin Films

    Energy Technology Data Exchange (ETDEWEB)

    Webb, J. D.; Moutinho, H. R.; Kazmerski, L. L.; Mueller, C. H.; Rivkin, T. V.; Treece, R. E.; Dalberth, M.; Rogers, C. T.

    1997-01-01

    Attenuated total reflectance (ATR) measurements were performed using Fourier transform infrared (FTIR) spectroscopy in the ATR mode with a thallium iodobromide (KRS-5) crystal to measure the frequencies of the v{sub 3} and v{sub 4} phonon absorption bands in thin strontium titanate films deposited on single-crystal yttrium-barium copper oxide (YBCO), lanthanum aluminate, magnesium oxide, and strontium titanate substrates. The KRS-5 crystal enabled FTIR-ATR measurements to be made at frequencies above 400 cm-1. Atomic force microscopy (AFM) and X-ray diffraction (XRD) measurements were also made to further characterize the films. The measurements were repeated on single-crystal specimens of strontium titanate and the substrates for comparison. Softening in the frequency of the v{sub 4} transverse optical phonon in the lattice-mismatched films below the established value of 544 cm-1 is indicative of the highly textured, polycrystalline ceramic nature of the films and is consistent with the XRD and AFM results.

  16. Infrared spectroscopic, x-ray, and nanoscale characterization of strontium titanate thin films

    Energy Technology Data Exchange (ETDEWEB)

    Webb, J.D.; Moutinho, H.R.; Kazmerski, L.L. [National Renewable Energy Lab., Golden, CO (United States); Mueller, C.H.; Rivkin, T.V.; Treece, R.E. [Superconducting Core Technologies, Inc., Golden, CO (United States); Dalberth, M.; Rogers, C.T. [Colorado Univ., Boulder, CO (United States). Dept. of Physics

    1996-04-01

    Attenuated total reflectance (ATR) measurements were performed using Fourier transform infrared (FTIR) spectroscopy in the ATR mode with a thallium iodobromide (KRS-5) crystal to measure the frequencies of the {nu}{sub 3} and {nu}{sub 4} phonon absorption bands in thin strontium titanate films deposited on single-crystal yttrium-barium copper oxide (YBCO), lanthanum aluminate, magnesium oxide, and strontium titanate substrates. The KRS-5 crystal enabled FTIR-ATR measurements to be made at frequencies above 400 cm{sup {minus}1}. Atomic force microscopy (AFM) and X-ray diffraction (XRD) measurements were also made to further characterize the films. The measurements were repeated on single-crystal specimens of strontium titanate and the substrates for comparison. Softening in the frequency of the {nu}{sub 4} transverse optical phonon in the lattice- mismatched films below the established value of 544 cm{sup {minus}1} is indicative of the highly textured, polycrystalline ceramic nature of the films and is consistent with the XRD and AFM results.

  17. Dielectric Properties of Strontium Titanate Filled Mullite Composites in Microwave Region

    Science.gov (United States)

    See, Alex; Hassan, Jumiah; Hashim, Mansor; Yusoff, W. Mohd. Daud Wan

    2008-05-01

    This research was designed to form better dielectric composite material using one steady state dielectric with a good dielectric material. Distinct dielectric composite was successfully produced using locally sourced kaolinite clay. The samples were made using kaolinite as the base matrix and Strontium Titanate (ST) added in varying ratios. Strontium Titanate were synthesized via solid-state reaction using Strontium Carbonate and rutile Titanium (IV) Oxide with sintering at 1300 °C. Local white kaolinite was used to fuse the barium titanate material in varying weight ratios. The powders were dry-mixed and made into pellets for calcination at 1000 °C. The dielectric measurements were carried out using the HP 4291B Impedance Analyzer dielectric setup. Three samples were prepared, namely 10%ST, 20%ST and 30%ST. The dielectric measurements were carried out at room temperature. Microwave region measurements showed steady state and linear dielectric relaxation ranging from 7 in the control sample and dropping down to 5 in 30%ST. The responses indicate linear relation between ST addition and microwave region dielectric permittivity

  18. 75 FR 20625 - Barium Chloride From China

    Science.gov (United States)

    2010-04-20

    ... From the Federal Register Online via the Government Publishing Office INTERNATIONAL TRADE COMMISSION Barium Chloride From China AGENCY: United States International Trade Commission. ACTION: Revised schedule for the subject review. DATES: Effective Date: April 9, 2010. FOR FURTHER INFORMATION CONTACT:...

  19. Neutral Barium Cloud Evolution at Different Altitudes

    Institute of Scientific and Technical Information of China (English)

    李磊; 徐荣栏

    2002-01-01

    Considering the joint effects of diffusion, collision, oxidation and photoionization, we study the evolution of the barium cloud at different altitudes in the space plasma active experiment. The results present the variation of the loss rate, number density distribution and brightness of the barium cloud over the range from 120 to 260km.This can be divided into oxidation, oxidation plus photoionization and photoionization regions.

  20. Life history inhomogeneity in Baltic Sea whitefish populations revealed by otolith strontium signatures – identification of stocked fish

    Directory of Open Access Journals (Sweden)

    Henry Hägerstrand

    2015-11-01

    The strontium concentrations in the otolith cores of whitefish from River Tornionjoki were higher than that of the four otoliths with low core strontium from fishes caught at sea (Table 1. Supposing that this latter group represent stocked fish raised in freshwater ponds, the vast majority of River Tornionjoki whitefish is naturally reproduced fish. This is plausible because in River Tornionjoki, the major whitefish spawning river in Finland, no larger stocking have been made since 1990s (Jokikokko and Huhmarniemi 2014. In conclusion, the concentration of otolith core strontium differs in whitefish hatched in fresh-water and in whitefish hatched in river water or in brackish Baltic Sea water. This difference can be used to reveal stocked whitefish. Barium concentration may be an even better indicator in this respect than strontium, as previous results indicate (Hägerstrand et al., 2015. Stocked river spawning whitefish appear in large amount at the southern feeding grounds around the Åland Islands, as already indicated by e.g. Leskelä et al. (2009.

  1. Bacterial Reduction Of Barium Sulphate By Sulphate-Reducing Bacteria

    Directory of Open Access Journals (Sweden)

    Luptáková Alena

    2015-12-01

    Full Text Available Acid mine drainage (AMD is a worldwide problem leading to contamination of water sources. AMD are characterized by low pH and high content of heavy metals and sulphates. The barium salts application presents one of the methods for the sulphates removing from AMD. Barium chloride, barium hydroxide and barium sulphide are used for the sulphates precipitation in the form of barium sulphate. Because of high investment costs of barium salts, barium sulphide is recycled from barium sulphate precipitates. It can be recycled by thermic or bacterial reduction of barium sulphate. The aim of our study was to verify experimentally the possibility of the bacterial transformation of BaSO4 to BaS by sulphate-reducing bacteria. Applied BaSO4 came from experiments of sulphates removal from Smolnik AMD using BaCl2.

  2. Thermochemical hydrogen production via a cycle using barium and sulfur - Reaction between barium sulfide and water

    Science.gov (United States)

    Ota, K.; Conger, W. L.

    1977-01-01

    The reaction between barium sulfide and water, a reaction found in several sulfur based thermochemical cycles, was investigated kinetically at 653-866 C. Gaseous products were hydrogen and hydrogen sulfide. The rate determining step for hydrogen formation was a surface reaction between barium sulfide and water. An expression was derived for the rate of hydrogen formation.

  3. Sulphate removal from sodium sulphate-rich brine and recovery of barium as a barium salt mixture.

    Science.gov (United States)

    Vadapalli, Viswanath R K; Zvimba, John N; Mulopo, Jean; Motaung, Solly

    2013-01-01

    Sulphate removal from sodium sulphate-rich brine using barium hydroxide and recovery of the barium salts has been investigated. The sodium sulphate-rich brine treated with different dosages of barium hydroxide to precipitate barium sulphate showed sulphate removal from 13.5 g/L to less than 400 mg/L over 60 min using a barium to sulphate molar ratio of 1.1. The thermal conversion of precipitated barium sulphate to barium sulphide achieved a conversion yield of 85% using coal as both a reducing agent and an energy source. The recovery of a pure mixture of barium salts from barium sulphide, which involved dissolution of barium sulphide and reaction with ammonium hydroxide resulted in recovery of a mixture of barium carbonate (62%) and barium hydroxide (38%), which is a critical input raw material for barium salts based acid mine drainage (AMD) desalination technologies. Under alkaline conditions of this barium salt mixture recovery process, ammonia gas is given off, while hydrogen sulfide is retained in solution as bisulfide species, and this provides basis for ammonium hydroxide separation and recovery for reuse, with hydrogen sulfide also recoverable for further industrial applications such as sulfur production by subsequent stripping.

  4. Spectroscopic (multi-energy) CT distinguishes iodine and barium contrast material in MICE

    CERN Document Server

    Anderson, NG; Firsching, M; de Ruiter, N; Schleich, N; Butzer, J S; Cook, N J; Grasset, R; Campbell, M; Scott, N J A; Anderson, N G

    2010-01-01

    Spectral CT differs from dual-energy CT by using a conventional X-ray tube and a photon-counting detector. We wished to produce 3D spectroscopic images of mice that distinguished calcium, iodine and barium. We developed a desktop spectral CT, dubbed MARS, based around the Medipix2 photon-counting energy-discriminating detector. The single conventional X-ray tube operated at constant voltage (75 kVp) and constant current (150 A mu A). We anaesthetised with ketamine six black mice (C57BL/6). We introduced iodinated contrast material and barium sulphate into the vascular system, alimentary tract and respiratory tract as we euthanised them. The mice were preserved in resin and imaged at four detector energy levels from 12 keV to 42 keV to include the K-edges of iodine (33.0 keV) and barium (37.4 keV). Principal component analysis was applied to reconstructed images to identify components with independent energy response, then displayed in 2D and 3D. Iodinated and barium contrast material was spectrally distinct f...

  5. BARIUM SULPHATE ABSORPTION AND THE SERUM DIAGNOSIS OF SYPHILIS.

    Science.gov (United States)

    Noguchi, H; Bronfenbrenner, J

    1911-02-01

    for the fixing combination of syphilitic serum and antigen. Speaking quantitatively, one unit of the syphilitic antibodies plus antigen will fix 0.1 cubic centimeter of guinea pig complement, but this unit can also be saturated and blocked by nearly the same amount of the seemingly indifferent serum component of the serum to be tested. Moreover, the regular amount of inactivated serum used in the Wassermann system is 0.2 cubic centimeter, a quantity sufficient to saturate two units of the fixing combination. Fortunately, this self-saturation of the syphilitic antibody-antigen combination by the other serum components is not constant in occurrence, owing to the wide variations of the fixability of the serum components of man. Here the benefit of Wechselmann's procedure becomes obvious. By removing a surplus of the fixable indifferent serum components by means of barium sulphate, the serum is made to react positively, or more strongly than before the treatment with barium sulphate. This masking of the positive reaction through the self-saturation is liable to occur in any system in which inactivated serum is recommended. Another equally important factor in masking the positive reaction in a serum in which the antibodies are poor, is the presence in considerable amount of natural antisheep amboceptor in human serum. It is a plain and simple fact that an excess of hemolytic amboceptor renders a positive reaction feeble or completely negative. As we have shown in our present investigation, a hemolytic amboceptor can be removed from the serum by means of absorption with barium sulphate. Thus it is easy to understand why Wechselmann found that barium sulphate absorption improves the reaction in the original Wassermann system. The treatment of syphilitic serum with this salt can have a twofold benefit in the case of the original method of Wassermann; namely, the removal of certain interfering serum components and the removal or diminishing of the natural antisheep amboceptor

  6. Synthesis of barium mercaptides and application of antimony/barium mercaptides

    Institute of Scientific and Technical Information of China (English)

    瞿龙; 张露露; 舒万艮

    2001-01-01

    Mercaptoacetic acid, isooctyl thioglycolate and barium hydroxide used as start materials, barium bis (2-ethylhexyl thioglycolate) (Ba(2EHTG)2), barium thioglycolate (Ba(TG)) and barium bisthioglycolate (Ba(TG)2) were synthesized. Their optimum synthetic techniques were discussed, and some physicochemical data were reported. Infrared spectroscopy and elemental analysis methods were used to identify the structures. They were put into PVC plastic products together with antimony tris (2-ethylhexyl thioglycolate) (Sb(2EHTG)3) under the suitable compounding, and their heat stability to PVC was studied. It is shown that these barium mercaptides have remarkable synergisms with antimony mercaptides and the long-term stabilizing effect of organoantimony stabilizer can be effectively improved, reducing the amount of antimony compounds so as to avoid the decrease of its stabilizing effect.

  7. Investigation of resistive switching in barium strontium titanate thin films for memory applications

    Energy Technology Data Exchange (ETDEWEB)

    Shen, Wan

    2010-11-17

    Resistive random access memory (RRAM) has attracted much attention due to its low power consumption, high speed operation, non-readout disturbance and high density integration potential and is regarded as one of the most promising candidates for the next generation non-volatile memory. The resistive switching behavior of Mn-doped BaSrTiO{sub 3} (BST) thin films with different crystalline properties was investigated within this dissertation. The laser fluence dependence was checked in order to optimize the RRAM properties. Although the film epitaxial quality was improved by reducing the laser energy during deposition process, the yields fluctuated and only 3% RRAM devices with highest epitaxial quality of BST film shows resistive switching behavior instead of 67% for the samples with worse film quality. It gives a clue that the best thin film quality does not result in the best switching performance, and it is a clear evidence of the importance of the defects to obtain resistive switching phenomena. The bipolar resistive switching behavior was studied with epitaxial BST thin films on SRO/STO. Compared to Pt top electrode, the yield, endurance and reliability were strongly improved for the samples with W top electrode. Whereas the samples with Pt top electrode show a fast drop of the resistance for both high and low resistance states, the devices with W top electrode can be switched for 10{sup 4} times without any obvious degradation. The resistance degradation for devices with Pt top electrode may result from the diffusion of oxygen along the Pt grain boundaries during cycling whereas for W top electrode the reversible oxidation and reduction of a WO{sub x} layer, present at the interface between W top electrode and BST film, attributes to the improved switching property. The transition from bipolar to unipolar resistive switching in polycrystalline BST thin films was observed. A forming process which induces a metallic low resistance state is prerequisite for the observation of unipolar switching behavior. The absence of unipolar switching in single crystalline samples may relate to space charge depletion layers at grain boundaries and their impact on the electronic conduction properties as well as the different local heat transfer in thin films. By controlling the switching voltage, the bipolar and unipolar resistive switching can be alternated in polycrystalline BST thin films. The bipolar/unipolar alternation is dynamically repeatable and the alternation may relate to the local modification of broken filaments by breakdown or oxygen vacancy movement. (orig.)

  8. Barium iodide and strontium iodide crystals and scintillators implementing the same

    Energy Technology Data Exchange (ETDEWEB)

    Payne, Stephen A.; Cherepy, Nerine; Pedrini, Christian; Burger, Arnold

    2016-09-13

    In one embodiment, a crystal includes at least one metal halide; and an activator dopant comprising ytterbium. In another general embodiment, a scintillator optic includes: at least one metal halide doped with a plurality of activators, the plurality of activators comprising: a first activator comprising europium, and a second activator comprising ytterbium. In yet another general embodiment, a method for manufacturing a crystal suitable for use in a scintillator includes mixing one or more salts with a source of at least one dopant activator comprising ytterbium; heating the mixture above a melting point of the salt(s); and cooling the heated mixture to a temperature below the melting point of the salts. Additional materials, systems, and methods are presented.

  9. ARTICLES: Photoinduced light scattering in cerium-doped barium strontium niobate crystals

    Science.gov (United States)

    Voronov, Valerii V.; Dorosh, I. R.; Kuz'minov, Yu S.; Tkachenko, N. V.

    1980-11-01

    Photoinduced light scattering was observed in cerium-doped (SrxBa1-x)1-y(Nb2O6)y crystals having the composition x = 0.61, y = 0.4993. It was found that this effect is due to holographic amplification of light scattered by crystal defects. An analysis is made of static and dynamic characteristics of self-amplification of scattered light in the crystals. A theoretical model of the process is constructed assuming that the hologram recording process is of the diffusion type. Theoretical results are compared with the experiment.

  10. Photoinduced light scattering in cerium-doped barium strontium niobate crystals

    Science.gov (United States)

    Voronov, V. V.; Dorosh, I. R.; Kuz'minov, Yu. S.; Tkachenko, N. V.

    Photoinduced light scattering was observed in cerium-doped (Srx Ba1-x)1-y(Nb2O6)y crystals having the composition x = 0.61, y = 0.4993. It was found that this effect is due to holographic amplification of light scattered by crystal defects. An analysis is made of static and dynamic characteristics of self-amplification of scattered light in the crystals. A theoretical model of the process is constructed assuming that the hologram recording process is of the diffusion type. Theoretical results are compared with the experiment.

  11. Crystallization of Reduced Strontium and Barium Niobate Perovskites from Borate Fluxes.

    NARCIS (Netherlands)

    Hessen, B.; Sunshine, S.A.; Siegrist, T.; Jimenez, R.

    1991-01-01

    Single crystals of three AxNbO3 (A = Sr, Ba) reduced niobate cubic perovskites have been obtained by recrystallization of reduced ternary ceramic precursors from borate fluxes under high-vacuum. Product formation could be influenced by variation of the alkaline-earth metal oxide content of the flux,

  12. Crystallization Kinetics of Barium and Strontium Aluminosilicate Glasses of Feldspar Composition

    Science.gov (United States)

    Hyatt, Mark J.; Bansal, Narottam P.

    1994-01-01

    Crystallization kinetics of BaO.Al2O3.2SiO2 (BAS) and SrO.Al2O3.2SiO2 (SAS) glasses in bulk and powder forms have been studied by non-isothermal differential scanning calorimetry (DSC). The crystal growth activation energies were evaluated to be 473 and 451 kJ/mol for bulk samples and 560 and 534 kJ/mol for powder specimens in BAS and SAS glasses, respectively. Development of crystalline phases on thermal treatments of glasses at various temperatures has been followed by powder x-ray diffraction. Powder samples crystallized at lower temperatures than the bulk and the crystallization temperature was lower for SAS glass than BAS. Crystallization in both glasses appeared to be surface nucleated. The high temperature phase hexacelsian, MAl2Si2O8 (M = Ba or Sr), crystallized first by nucleating preferentially on the glass surface. Also, monoclinic celsian does not nucleate directly in the glass, but is formed at higher temperatures from the transformation of the metastable hexagonal phase. In SAS the transformation to monoclinic celsian occurred rapidly after 1 h at 1100 C. In contrast, in BAS this transformation is sluggish and difficult and did not go to completion even after 10 h heat treatment at 1400 C. The crystal growth morphologies in the glasses have been observed by optical microscopy. Some of the physical properties of the two glasses are also reported.

  13. Europium-activated barium/strontium silicates for near-UV light emitting diode applications

    Energy Technology Data Exchange (ETDEWEB)

    Han, J.K. [University of California, San Diego, Materials Science and Engineering Program, La Jolla, CA 92093 (United States); Hannah, M.E.; Piquette, A. [OSRAM SYLVANIA Central Research, 71 Cherry Hill Drive Beverly, MA 01915 (United States); Micone, J. [University of California, San Diego, Materials Science and Engineering Program, La Jolla, CA 92093 (United States); Hirata, G.A. [Centro de Nanociencias y Nanotecnolgia, Universidad Nacional Autonoma de Mexico, Km. 107 Carretera Tijuana-Ensenada Apdo, Ensenada, MX CP 22860 (Mexico); Talbot, J.B. [University of California, San Diego, Materials Science and Engineering Program, La Jolla, CA 92093 (United States); University of California, San Diego, Department of Nanoengineering, La Jolla, CA 92093 (United States); Mishra, K.C. [OSRAM SYLVANIA Central Research, 71 Cherry Hill Drive Beverly, MA 01915 (United States); McKittrick, J., E-mail: jmckittrick@UCSD.Edu [University of California, San Diego, Materials Science and Engineering Program, La Jolla, CA 92093 (United States); University of California, San Diego, Department of Mechanical and Aerospace Engineering, La Jolla, CA 92093 (United States)

    2013-01-15

    This paper reports on the luminescence properties of submicron-sized green-yellow emitting (Ba{sub 1-x}Sr{sub x}Eu{sub 0.03}){sub 2}SiO{sub 4} (0{<=}x{<=}1) phosphors. These phosphors were prepared by a modified sol-gel/Pechini method. The X-ray diffraction analysis shows that the single phase products are obtained. The particle size - ranges from 200 to 500 nm with a spherical or needlelike shape depending on x. These phosphors show strong absorption in the near UV range and the photoluminescence emission spectra consist of a strong broad green-yellow band centered between 512 and 570 nm, depending on x. Furthermore, the phosphors have high quantum efficiencies: 94% for x=0 and 85% for x=0.25. The emission lifetime at 400 K is 97% of that at 40 K, demonstrating good thermal stability. - Highlights: Black-Right-Pointing-Pointer (Ba{sub 1-x}Sr{sub x}Eu{sub 0.03}){sub 2}SiO{sub 4} (0{<=}x{<=}1) phosphors were prepared by a sol-gel/Pechini method. Black-Right-Pointing-Pointer Submicron-sized (200-500 nm) particle had a spherical or needlelike morphology. Black-Right-Pointing-Pointer Strong absorption and high quantum efficiencies (85-94%) in the near UV range. Black-Right-Pointing-Pointer Emission lifetime at 400 K is 97% of that at 40 K, showing good thermal stability.

  14. Measurement of Elastic Modulus of Alumina and Barium Strontium Titanate Wafers Produced by Tape Casting Method

    Science.gov (United States)

    2014-02-01

    measurements – Generally in the 230 to 250 GPa range * VTT manufacturing, 1996, ISBN 951-38-4987-2 Figure 7 Modulus measurements on 0.5-mm wafers of...Capacitors,”1998 Society of Automotive Engineers. 4. Barsoum, Michel, “Fundamentals of Ceramics,” cap.11, p. 401. 5. VTT Manufacturing, ISBN 951-38

  15. Thin film barium strontium titanate capacitors for tunable RF front-end applications

    NARCIS (Netherlands)

    Tiggelman, Markus Petrus Josephus

    2009-01-01

    In this thesis, the results of intensive electrical characterization, modeling and the design of hardware with thin film tunable capacitors, i.e., dielectric varactors, has been presented and discussed. Especially the quality factor Q and the tuning ratio of the tunable capacitors have been studied

  16. Abundance analysis of Barium stars

    Institute of Scientific and Technical Information of China (English)

    Guo-Qing Liu; Yan-Chun Liang; Li-Cai Deng

    2009-01-01

    We obtain the chemical abundances of six barium stars and two CH subgiant stars based on the high signal-to-noise ratio and high resolution Echelle spectra. The neu- tron capture process elements Y, Zr, Ba, La and Eu show obvious overabundances relative to the Sun, for example, their [Ba/Fe] values are from 0.45 to 1.27. Other elements, in- cluding Na, Mg, A1, Si, Ca, Sc, Ti, V, Cr, Mn and Ni, show comparable abundances to the Solar ones, and their [Fe/H] covers a range from -0.40 to 0.21, which means they belong to the Galactic disk. The predictions of the theoretical model of wind accretion for bi- nary systems can explain the observed abundance patterns of the neutron capture process elements in these stars, which means that their overabundant heavy-elements could be caused by accreting the ejecta of AGB stars, the progenitors of present-day white dwarf companions in binary systems.

  17. Individual-specific transgenerational marking of fish populations based on a barium dual-isotope procedure.

    Science.gov (United States)

    Huelga-Suarez, Gonzalo; Moldovan, Mariella; Garcia-Valiente, America; Garcia-Vazquez, Eva; Alonso, J Ignacio Garcia

    2012-01-01

    The present study focuses on the development and evaluation of an individual-specific transgenerational marking procedure using two enriched barium isotopes, (135)Ba and (137)Ba, mixed at a given and selectable molar ratio. The method is based on the deconvolution of the isotope patterns found in the sample into four molar contribution factors: natural xenon (Xe nat), natural barium (Ba nat), Ba135, and Ba137. The ratio of molar contributions between Ba137 and Ba135 is constant and independent of the contribution of natural barium in the sample. This procedure was tested in brown trout ( Salmo trutta ) kept in captivity. Trout were injected with three different Ba137/Ba135 isotopic signatures ca. 7 months and 7 days before spawning to compare the efficiency of the marking procedure at long and short term, respectively. The barium isotopic profiles were measured in the offspring by means of inductively coupled plasma mass spectrometry. Each of the three different isotopic signatures was unequivocally identified in the offspring in both whole eggs and larvae. For 9 month old offspring, the characteristic barium isotope signatures could also be detected in the otoliths even in the presence of a high and variable amount of barium of natural isotope abundance. In conclusion, it can be stated that the proposed dual-isotope marking is inheritable and can be detected after both long-term and short-term marking. Furthermore, the dual-isotope marking can be made individual-specific, so that it allows identification of offspring from a single individual or a group of individuals within a given fish group.

  18. Response of Ag Thick Film Microstripline due to Superstrate Strontium Substituted Bismuth Manganites

    Directory of Open Access Journals (Sweden)

    S.N. Mathad

    2014-06-01

    Full Text Available The purpose of this paper is to describe the use of strontium-substituted bismuth manganites bulk ceramic superstrate on Ag thick film microstripline, to modify its response and measure complex permittivity as a function of strontium. Bismuth strontium manganites (Bi1 − xSrxMnO3 have been synthesized by solid state sintering technique. The perturbation obtained in the transmittance and reflectance of thick film microstripline due to the Bi1 − xSrxMnO3 (0.20  x  0.50 overlay has been used to obtain the permittivity at microwave frequencies in X and Ku band range. Due to the overlay of Bismuth strontium manganites (BSM pellets a substantial increase in the effective dielectric constant was observed in X band more compared to Ku band. The in-touch overlay method provides ease loading and unloading. The perturbation obtained in the transmittance and reflectance of thick film microstripline due to the bismuth strontium manganites overlay has been used to obtain the permittivity.

  19. Varying Constants

    CERN Document Server

    Damour, Thibault Marie Alban Guillaume

    2003-01-01

    We review some string-inspired theoretical models which incorporate a correlated spacetime variation of coupling constants while remaining naturally compatible both with phenomenological constraints coming from geochemical data (Oklo; Rhenium decay) and with present equivalence principle tests. Barring unnatural fine-tunings of parameters, a variation of the fine-structure constant as large as that recently ``observed'' by Webb et al. in quasar absorption spectra appears to be incompatible with these phenomenological constraints. Independently of any model, it is emphasized that the best experimental probe of varying constants are high-precision tests of the universality of free fall, such as MICROSCOPE and STEP. Recent claims by Bekenstein that fine-structure-constant variability does not imply detectable violations of the equivalence principle are shown to be untenable.

  20. Solvothermal synthesis of strontium phosphate chloride nanowire

    Science.gov (United States)

    Lam, W. M.; Wong, C. T.; Li, Z. Y.; Luk, K. D. K.; Chan, W. K.; Yang, C.; Chiu, K. Y.; Xu, B.; Lu, W. W.

    2007-08-01

    Strontium phosphate chloride nanowire was synthesized via a solvothermal treatment of strontium tri-polyphosphate and Collin salt in 1,4-dioxane at 150 °C. The effects of 1,4-dioxane concentration on particle morphology, crystallinity and phase purity were investigated in this study. The specimen morphology was analyzed by transmission electron microscopy (TEM) and scanning electron microscopy (SEM). When the concentration of 1,4-dioxane was below 10%, micron-sized whisker was the dominant form. At 20-25% concentration of 1,4-dioxane, strontium phosphate chloride single-crystalline nanowire was 31±12 nm in diameter and 1.43±0.6 μm in length with an aspect ratio of 52.28±29.41. X-ray diffraction (XRD) pattern of this nanowire matched with that of strontium phosphate chloride (JCPDS #083-0973). When 1,4-dioxane concentration exceeded 25%, nanorod aggregate was the dominant form instead of nanowire. At 20-25% 1,4-dioxane concentration suitable strontium concentration combine with high chemical potential environment favors the formation of nanowires. By adding 1,4-dioxane impure phase such as β-strontium hydrogen phosphate, nanorod formation was suppressed. This method provides an efficient way to synthesize high aspect ratio strontium phosphate chloride nanowire. It has potential bioactive nanocomposite, high mechanical performance bioactive bone cement filler and fluorescent material applications.

  1. Coherent Dark Resonances in Atomic Barium

    CERN Document Server

    Dammalapati, U; Jungmann, K; Willmann, L

    2007-01-01

    The observation of dark-resonances in the two-electron atom barium and their influence on optical cooling is reported. In heavy alkali earth atoms, i.e. barium or radium, optical cooling can be achieved using n^1S_0-n^1P_1 transitions and optical repumping from the low lying n^1D_2 and n^3D_{1,2} states to which the atoms decay with a high branching ratio. The cooling and repumping transition have a common upper state. This leads to dark resonances and hence make optical cooling less inefficient. The experimental observations can be accurately modelled by the optical Bloch equations. Comparison with experimental results allows us to extract relevant parameters for effective laser cooling of barium.

  2. Improved spectrophotometric analysis of barium styphnate

    Energy Technology Data Exchange (ETDEWEB)

    Brown, N E; Blasi, J A

    1983-01-01

    A spectrophotometric procedure to determine the purity of barium styphnate monohydrate based upon the absorbance of the styphnate ion at 326 and 413.3 nm has been developed. The purity is determined by comparing the absorbance of the styphnate ion in barium styphnate and in styphnic acid. Our investigation has shown that the molar absorptivity and lambda maxima of the styphnate ion are quite pH dependent; therefore, the pH is buffered to 6.8 to 7.0 with ammonium acetate. Under these conditions the molar absorptivity is 1.6 x 10/sup 4/ L/mol-cm. Analyses following the procedure in the Navy specification WS13444A using water were found to give low molar absorptivities (1.3 x 10/sup 4/ L/mol-cm) for the styphnic acid calibration resulting in erroneous values for barium styphnate purity.

  3. Strontium Ions Substitution in Brushite Crystals: The Role of Strontium Chloride

    Directory of Open Access Journals (Sweden)

    Enrique López Cabarcos

    2011-05-01

    Full Text Available The incorporation of strontium chloride to brushite cement was successful to introduce strontium ions within the lattice of brushite crystals. The effect of strontium ions on brushite cement properties was concentration dependent; such that, the addition of 5% and 10% (w/w SrCl2 significantly increased the cement FST and the addition of 10% SrCl2 decreased the cement tensile strength. Further, cement weight loss was shown to be increased by cement modification with SrCl2. The combination of ionic substitution and the degradability of brushite cements would constitute a system for the local delivery of strontium ions in the treatment of osteoporosis.

  4. Strontium ions substitution in brushite crystals: the role of strontium chloride.

    Science.gov (United States)

    Alkhraisat, Mohammad H; Rueda, Carmen; López Cabarcos, Enrique

    2011-05-31

    The incorporation of strontium chloride to brushite cement was successful to introduce strontium ions within the lattice of brushite crystals. The effect of strontium ions on brushite cement properties was concentration dependent; such that, the addition of 5% and 10% (w/w) SrCl2 significantly increased the cement FST and the addition of 10% SrCl2 decreased the cement tensile strength. Further, cement weight loss was shown to be increased by cement modification with SrCl2. The combination of ionic substitution and the degradability of brushite cements would constitute a system for the local delivery of strontium ions in the treatment of osteoporosis.

  5. Electronic structure of nanograin barium titanate ceramics

    Institute of Scientific and Technical Information of China (English)

    DENG Xiangyun; WANG Xiaohui; LI Dejun; LI Longtu

    2007-01-01

    The density of states and band structure of 20 nm barium titanate(BaTiO3,BT)ceramics are investigated by first-principles calculation.The full potential linearized augmented plane wave(FLAPW)method is used and the exchange correlation effects are treated by the generalized gradient approximation(GGA).The results show that there is substantial hybridization between the Ti 3d and O 2p states in 20 nm BT ceramics and the interaction between barium and oxygen is typically ionic.

  6. Bentonite-Clay Waste Form for the Immobilization of Cesium and Strontium from Fuel Processing Waste Streams

    Energy Technology Data Exchange (ETDEWEB)

    Kaminski, Michael D. [Argonne National Lab. (ANL), Argonne, IL (United States); Mertz, Carol J. [Argonne National Lab. (ANL), Argonne, IL (United States)

    2016-01-01

    The physical properties of a surrogate waste form containing cesium, strontium, rubidium, and barium sintered into bentonite clay were evaluated for several simulant feed streams: chlorinated cobalt dicarbollide/polyethylene glycol (CCD-PEG) strip solution, nitrate salt, and chloride salt feeds. We sintered bentonite clay samples with a loading of 30 mass% of cesium, strontium, rubidium, and barium to a density of approximately 3 g/cm3. Sintering temperatures of up to 1000°C did not result in volatility of cesium. Instead, there was an increase in crystallinity of the waste form upon sintering to 1000ºC for chloride- and nitrate-salt loaded clays. The nitrate salt feed produced various cesium pollucite phases, while the chloride salt feed did not produce these familiar phases. In fact, many of the x-ray diffraction peaks could not be matched to known phases. Assemblages of silicates were formed that incorporated the Sr, Rb, and Ba ions. Gas evolution during sintering to 1000°C was significant (35% weight loss for the CCD-PEG waste-loaded clay), with significant water being evolved at approximately 600°C.

  7. Experimental investigation of the effect of titanium dioxide and barium titanate additives on DC transient currents in low density polyethylene

    DEFF Research Database (Denmark)

    Khalil, M.S; Henk, Peter O; Henriksen, Mogens

    1988-01-01

    The effect of titanium dioxide as a semiconductive additive and barium titanate as a highly polar additive on the DC transient currents in low-density polyethylene is investigated. Experiments were made using thick specimens under a high electric field (>25×106 V/m) and a constant temperature of 40...

  8. Study of structural, ferromagnetic and ferroelectric properties of nanostructured barium doped Bismuth Ferrite

    Energy Technology Data Exchange (ETDEWEB)

    Chaudhuri, A., E-mail: arkac123@gmail.com [Department of Applied Science, Haldia Institute of Technology, Dist.- Purba Medinipur, Haldia- 721657, West Bengal (India); Department of Condensed Matter Physics and Material Science, S.N. Bose National Center for Basic Sciences, Block JD, Salt Lake, Kolkata 700098 (India); Mandal, K. [Department of Applied Science, Haldia Institute of Technology, Dist.- Purba Medinipur, Haldia- 721657, West Bengal (India); Department of Condensed Matter Physics and Material Science, S.N. Bose National Center for Basic Sciences, Block JD, Salt Lake, Kolkata 700098 (India)

    2014-03-15

    Nanostructured multiferroic Bi{sub (1−x)}Ba{sub x}FeO{sub 3}x=0.0, 0.1, 0.2 were prepared by hydrothermal technique. All samples belonged to the rhombohedrally distorted perovskite structure. The morphology of the particles changed with the doping of barium. Effect of barium doping on the dielectric constant was studied over a wide frequency range of 1000 Hz–1 MHz. The activation energy due to relaxation and due to conduction was measured from the Cole Cole plot and the AC conductivity versus frequency plot respectively. The activation energy estimated from both the studies was close to each other. The activation energy also enhanced with the increase in the barium content. The magnetization at the highest available field (∼1.6 T) increased from 0.05 emu/g for the sample with x=0.0–12 emu/g for the sample with x=0.2. The magnetic measurements show a significant increase in magnetization around 400 °C. Remnant polarization for x=0.0 was negligible and it increased to 0.06 µC/cm{sup 2} for x=0.2. - Highlights: • Bismuth Ferrite nanostructures were synthesized by the hydrothermal technique. • Barium was doped in Bismuth site. • Morphology changed with doping. • Ferromagnetic, Ferroelectric and Dielectric properties enhanced with doping. • An unreported magnetic transition due to spin canting was observed near 550 °C.

  9. Strontium clusters: electronic and geometry shell effects

    DEFF Research Database (Denmark)

    Lyalin, Andrey G.; Solov'yov, Ilia; Greiner, Walter

    2008-01-01

    is governed by an interplay of the electronic and geometry shell closures. Influence of the electronic shell effects on structural rearrangements can lead to violation of the icosahedral growth motif of strontium clusters. It is shown that the excessive charge essentially affects the optimized geometry......The optimized structure and electronic properties of neutral, singly and doubly charged strontium clusters have been investigated using it ab initio theoretical methods based on density-functional theory. We have systematically calculated the optimized geometries of neutral, singly and doubly...... charged strontium clusters consisting of up to 14 atoms, average bonding distances, electronic shell closures, binding energies per atom, and spectra of the density of electronic states (DOS). It is demonstrated that the size-evolution of structural and electronic properties of strontium clusters...

  10. Surface adsorption in strontium chloride ammines

    DEFF Research Database (Denmark)

    Ammitzbøll, Andreas L.; Lysgaard, Steen; Klukowska, Agata

    2013-01-01

    An adsorbed state and its implications on the ab- and desorption kinetics of ammonia in strontium chloride ammine is identified using a combination of ammonia absorption measurements, thermogravimetric analysis, and density functional theory calculations. During thermogravimetric analysis, ammoni...

  11. Effects of Dysprosium Oxide Doping on Microstructure and Properties of Barium Titanate Ceramic

    Institute of Scientific and Technical Information of China (English)

    Pu Yongping; Ren Huijun; Chen Wei; Chen Shoutian

    2005-01-01

    Different amounts of dysprosium oxide were incorporated into barium titanate powders synthesized by hydrothermal method. Relations of substitution behaviors and lattice parameters with solid-solubility were studied. Furthermore, the influences of dysprosium oxide doping fraction on grain size and dielectric properties of barium titanate ceramic, including dielectric constant and breakdown electric field strength, were investigated via scanning electron microscope, X-ray diffraction and electric property tester. The results show that dysprosium oxide can restrain abnormal grain growth during sintering and that fine-grained and high density of barium titanate ceramic can result in excellent dielectric properties. As mass fraction of dysprosium oxide is 0.6%, the lattice parameters of grain increase to the maximum because of the lowest vacancy concentration. The electric property parameters are cited as following: dielectric constant (25 ℃) reaches 4100, the change in relative dielectric constant with temperature is -10% to 10% within the range of -15~100 ℃, breakdown electric field strength (alternating current) achieves 3.2 kV·mm-1, which can be used in manufacturing high voltage ceramic capacitors.

  12. Lattice dynamics of strontium tungstate

    Indian Academy of Sciences (India)

    Prabhatasree Goel; R Mittal; S L Chaplot; A K Tyagi

    2008-11-01

    We report here measurements of the phonon density of states and the lattice dynamics calculations of strontium tungstate (SrWO4). At ambient conditions this compound crystallizes to a body-centred tetragonal unit cell (space group I41/a) called scheelite structure. We have developed transferable interatomic potentials to study the lattice dynamics of this class of compounds. The model parameters have been fitted with respect to the experimentally available Raman and infra-red frequencies and the equilibrium unit cell parameters. Inelastic neutron scattering measurements have been carried out in the triple-axis spectrometer at Dhruva reactor. The measured phonon density of states is in good agreement with the theoretical calculations, thus validating the inter-atomic potential developed.

  13. Cesium and strontium ion specific exchangers

    Energy Technology Data Exchange (ETDEWEB)

    Yates, S.

    1996-10-01

    This work is one of two parallel projects that are part of an ESP task to develop high-capacity, selective, solid extractants for cesium, strontium, and technetium from nuclear wastes. In this subtask, Pacific Northwest National Laboratory (PNNL) is collaborating with AlliedSignal, Inc. (Des Plaines, Illinois) to develop inorganic ion exchangers that are selective for strontium and cesium from alkaline high-level waste and groundwater streams.

  14. Preparation of the Superconductor Substrate: Strontium Titanate

    Science.gov (United States)

    1988-09-01

    single crystals of strontium titanate is derived from the original method developed by Verneuil . 16 The general procedure for the growth of single... crystals growth are reported. The growth direction was determined to be 5 degrees away from the [2111 direction. ICP-emission spectroscopy irdicates... Growth of Strontium Titanate Crystals 5 2.4 Preparation of Substrates 8 3. RESULTS AND CONCLUSIONS 8 REFERENCES 13 Illustrations 1. Schematic Diagram

  15. Vitrification of strontium-90 fluoride

    Energy Technology Data Exchange (ETDEWEB)

    Strachan, D.M.; Schulz, W.W.

    1977-04-01

    At Hanford, strontium-90 is removed from high-level nuclear fuel reprocessing waste and converted to strontium-90 fluoride. This /sup 90/SrF/sub 2/ is doubly encapsulated in high-integrity containers which are placed under water in monitored storage pools. Conversion of /sup 90/SrF/sub 2/ to a more immobile compound may be necessary and/or desirable as part of the overall plan for the long-term management of Hanford Defense Wastes. Glasses containing up to 40 mass percent SrF/sub 2/ and having leach rates in the range 1 x 10/sup -8/ to 1 x 10/sup -5/ gram Sr/(m/sup 2/ . s) (1 x 10/sup -7/ to 1 x 10/sup -4/ g Sr/cm/sup 2/ . day)) have now been prepared. From 0.2 to 5 percent of the fluorine is volatilized during the melting of the glass batch at temperatures up to 1500/sup 0/K. At present, the heat generation limit for commercial glasses stored at a nuclear waste repository is 5 kW per canister. All glasses described here would exceed that limit by more than a factor of five. The stored /sup 90/SrF/sub 2/ may be treated separately from the bulk of Hanford waste, in which case it would be diluted to an acceptable power level with inert chemicals in the glass batch. Another option is to blend the /sup 90/SrF/sub 2/ with the bulk of the other Hanford wastes when those wastes are converted to some immobile form.

  16. Work Function Calculation For Hafnium- Barium System

    Directory of Open Access Journals (Sweden)

    K.A. Tursunmetov

    2015-08-01

    Full Text Available The adsorption process of barium atoms on hafnium is considered. A structural model of the system is presented and on the basis of calculation of interaction between ions dipole system the dependence of the work function on the coating.

  17. Thermal decomposition of barium valerate in argon

    DEFF Research Database (Denmark)

    Torres, P.; Norby, Poul; Grivel, Jean-Claude

    2015-01-01

    The thermal decomposition of barium valerate (Ba(C4H9CO2)(2)/Ba-pentanoate) was studied in argon by means of thermogravimetry, differential thermal analysis, IR-spectroscopy, X-ray diffraction and hot-stage optical microscopy. Melting takes place in two different steps, at 200 degrees C and 280...

  18. Scattering lengths of calcium and barium isotopes

    NARCIS (Netherlands)

    Dammalapati, U.; Willmann, L.; Knoop, S.

    2011-01-01

    We have calculated the s-wave scattering length of all the even isotopes of calcium (Ca) and barium (Ba) in order to investigate the prospect of Bose-Einstein condensation (BEC). For Ca we have used an accurate molecular potential based on detailed spectroscopic data. Our calculations show that Ca

  19. Barium Ferrite Films Grown by Laser Ablation

    NARCIS (Netherlands)

    Lisfi, A.; Lodder, J.C.; Haan, de P.; Smithers, M.A.; Roesthuis, F.J.G.

    1998-01-01

    Pulsed laser ablation (PLA) has been used to grow barium ferrite films on Al2O3 single crystal substrates. When deposition occurs in an oxidising atmosphere at high temperatures, the films are single BaFe12O19 phase, very well oriented with (001) texture, and exhibit a large perpendicular magnetic a

  20. Strontium ranelate for the management of osteoporosis.

    Science.gov (United States)

    Lam, Sum; Zouzias, Katerina

    2008-07-01

    To evaluate the role of strontium ranelate in the management of osteoporosis. A MEDLINE (January 1966 to May 2007) search using the terms osteoporosis, strontium ranelate, bonemineral density, and fractures. All English-language articles identified from the data sources were evaluated. Strontium ranelate stimulates bone formation and inhibits bone resorption. Its safety and efficacy for osteoporosis were evaluated in four prospective, randomized, double-blind, placebo-controlled trials. The PREVOS (Prevention of Early Postmenopausal Bone Loss by Strontium Ranelate) trial suggested that 1 g daily is the optimal dose for preventing postmenopausal bone loss and was associated with a 1.41% increase in lumbar bone-mineral density (BMD). However, the STRATOS (Strontium Administration for Treatment of Osteoporosis) study found that a 1 g daily regimen was associated with a higher incidence of new vertebral deformities, and a 2 g daily regimen reduced lumbar BMD by 3% in postmenopausal, osteoporotic women. The SOTI (Spinal Osteoporosis Therapeutic Intervention) and TROPOS (Treatment of Peripheral Osteoporosis) studies suggested that a 2 g daily regimen reduced vertebral fractures by 39% to 41%, nonvertebral fractures by 16%, in postmenopausal, osteoporotic women. Most common adverse events reported were nausea and diarrhea. Four clinical trials demonstrated the efficacy and safety of strontium ranelate for the management of postmenopausal osteoporosis; however, the Food and Drug Administration has not approved it for this indication.

  1. MATHEMATICAL CONSTANTS.

    Energy Technology Data Exchange (ETDEWEB)

    Robinson, H.P.; Potter, Elinor

    1971-03-01

    This collection of mathematical data consists of two tables of decimal constants arranged according to size rather than function, a third table of integers from 1 to 1000, giving some of their properties, and a fourth table listing some infinite series arranged according to increasing size of the coefficients of the terms. The decimal values of Tables I and II are given to 20 D.

  2. Hemaka's constant

    CERN Document Server

    Sparavigna, Amelia Carolina

    2012-01-01

    As proposed in a previous paper, the decorations of ancient objects can provide some information on the approximate evaluations of constant {\\pi}, the ratio of circumference to diameter. Here we discuss some disks found in the tomb of Hemaka, the chancellor of a king of the First Dynasty of Egypt, about 3000 BC. The discussion is based on measurements of the dimensionless ratio of lengths.

  3. Engineered Materials for Cesium and Strontium Storage Final Technical Report

    Energy Technology Data Exchange (ETDEWEB)

    Sean M. McDeavitt

    2010-04-14

    Closing the nuclear fuel cycle requires reprocessing spent fuel to recover the long-lived components that still have useful energy content while immobilizing the remnant waste fission products in stable forms. At the genesis of this project, next generation spent fuel reprocessing methods were being developed as part of the U.S. Department of Energy's Advanced Fuel Cycle Initiative. One of these processes was focused on solvent extraction schemes to isolate cesium (Cs) and strontium (Sr) from spent nuclear fuel. Isolating these isotopes for short-term decay storage eases the design requirements for long-term repository disposal; a significant amount of the radiation and decay heat in fission product waste comes from Cs-137 and Sr-90. For the purposes of this project, the Fission Product Extraction (FPEX) process is being considered to be the baseline extraction method. The objective of this project was to evaluate the nature and behavior of candidate materials for cesium and strontium immobilization; this will include assessments with minor additions of yttrium, barium, and rubidium in these materials. More specifically, the proposed research achieved the following objectives (as stated in the original proposal): (1) Synthesize simulated storage ceramics for Cs and Sr using an existing labscale steam reformer at Purdue University. The simulated storage materials will include aluminosilicates, zirconates and other stable ceramics with the potential for high Cs and Sr loading. (2) Characterize the immobilization performance, phase structure, thermal properties and stability of the simulated storage ceramics. The ceramic products will be stable oxide powders and will be characterized to quantify their leach resistance, phase structure, and thermophysical properties. The research progressed in two stages. First, a steam reforming process was used to generate candidate Cs/Sr storage materials for characterization. This portion of the research was carried out at

  4. Barium carbonate as an agent to improve the electrical properties of neodymium-barium-copper system at high temperature

    Energy Technology Data Exchange (ETDEWEB)

    Fernandes, J.P. [Post-Graduate Program in Chemical Engineering, Universidade Federal de Santa Catarina (UFSC), Florianópolis, SC, 88040-900 (Brazil); Duarte, G.W. [Post-Graduate Program in Chemical Engineering, Universidade Federal de Santa Catarina (UFSC), Florianópolis, SC, 88040-900 (Brazil); Research Group in Technology and Information, Centro Universitário Barriga Verde (UNIBAVE), Santa Catarina, SC (Brazil); Caldart, C. [Post-Graduate Program in Science and Materials Engineering, Universidade do Extremo Sul Catarinense (UNESC), Criciúma, SC, 88806-000 (Brazil); Kniess, C.T. [Post-Graduate Program in Professional Master in Management, Universidade Nove de Julho, São Paulo, SP (Brazil); Montedo, O.R.K.; Rocha, M.R. [Post-Graduate Program in Science and Materials Engineering, Universidade do Extremo Sul Catarinense (UNESC), Criciúma, SC, 88806-000 (Brazil); Riella, H.G. [Post-Graduate Program in Chemical Engineering, Universidade Federal de Santa Catarina (UFSC), Florianópolis, SC, 88040-900 (Brazil); Fiori, M.A., E-mail: fiori@unochapeco.edu.br [Post-Graduate Program in Environmental Science, Universidade Comunitária da Região de Chapecó (UNOCHAPECÓ), Chapecó, SC, 89809-000 (Brazil); Post-Graduate Program in Technology and Management of the Innovation, Universidade Comunitária da Região de Chapecó (UNOCHAPECÓ), Chapecó, SC, 89809-000 (Brazil)

    2015-11-15

    Specialized ceramics are manufactured under special conditions and contain specific elements. They possess unique electrical and thermal properties and are frequently used by the electronics industry. Ceramics containing neodymium-barium-copper (NBC) exhibit high conductivities at low temperatures. NBC-based ceramics are typically combined with oxides, i.e., NBCo produced from neodymium oxide, barium oxide and copper oxide. This study presents NBC ceramics that were produced with barium carbonate, copper oxide and neodymium oxide (NBCa) as starting materials. These ceramics have good electrical conductivities at room temperature. Their conductivities are temperature dependent and related to the starting amount of barium carbonate (w%). - Highlights: • The new crystalline structure were obtained due presence of the barium carbonate. • The NBCa compound has excellent electrical conductivity at room temperature. • The grain crystalline morphology was modified by presence of the barium carbonate. • New Phases α and β were introduced by carbonate barium in the NBC compound.

  5. Solubility of strontium-substituted apatite by solid titration

    OpenAIRE

    Pan, HB; Darvell, BW; Luk, KDK; Lu, WW; Li, ZY; Lam, WM; Wong, JC

    2009-01-01

    Solid titration was used to explore the solubility isotherms of partially (Srx-HAp, x = 1, 5, 10, 40, 60 mol.%) and fully substituted strontium hydroxyapatite (Sr-HAp). Solubility increased with increasing strontium content. No phase other than strontium-substituted HAp, corresponding to the original titrant, was detected in the solid present at equilibrium; in particular, dicalcium hydrogen phosphate was not detected at low pH. The increase in solubility with strontium content is interpreted...

  6. Physical barrier effect of geopolymeric waste form on diffusivity of cesium and strontium.

    Science.gov (United States)

    Jang, J G; Park, S M; Lee, H K

    2016-11-15

    The present study investigates the physical barrier effect of geopolymeric waste form on leaching behavior of cesium and strontium. Fly ash-based geopolymers and slag-blended geopolymers were used as solidification agents. The leaching behavior of cesium and strontium from geopolymers was evaluated in accordance with ANSI/ANS-16.1. The diffusivity of cesium and strontium in a fly ash-based geopolymer was lower than that in Portland cement by a factor of 10(3) and 10(4), respectively, showing significantly improved immobilization performance. The leaching resistance of fly ash-based geopolymer was relatively constant regardless of the type of fly ash. The diffusivity of water-soluble cesium and strontium ions were highly correlated with the critical pore diameter of the binder. The critical pore diameter of the fly ash-based geopolymer was remarkably smaller than those of Portland cement and slag-blended geopolymer; consequently, its ability physically to retard the diffusion of nuclides (physical barrier effect) was superior.

  7. Scaled-energy spectroscopy of a |M|=1 Rydberg barium atom in an electric field

    Institute of Scientific and Technical Information of China (English)

    Wang Lei; Quan Wei; Shen Li; Yang Hai-Feng; Shi Ting-Yun; Liu Xiao-Jun; Liu Hong-Ping; Zhan Ming-Sheng

    2009-01-01

    We observe strong energy-dependent quantum defects in the scaled-energy Stark spectra for |M|=1 Rydberg states of barium atoms at three scaled energies: ε= -2.000, ε= -2.500 and ε=-3.000. In an attempt to explain the observations, theoretical calculations of closed orbit theory based on a model potential including core effect are performed for non-hydrogenic atoms. While such a potential has been uniformly successful for alkali atoms with a single valence electron, it fails to match experimental results for barium atoms in the 6snp Rydberg states with two valence electrons. Our study points out that this discrepancy is due to the strong perturbation from the 5d8p state, which voids the simple approximation for constant quantum defects of principle quantum number n.

  8. Specific activity and isotope abundances of strontium in purified strontium-82

    Energy Technology Data Exchange (ETDEWEB)

    Fitzsimmons, J. M.; Medvedev, D. G.; Mausner, L. F.

    2015-11-12

    A linear accelerator was used to irradiate a rubidium chloride target with protons to produce strontium-82 (Sr-82), and the Sr-82 was purified by ion exchange chromatography. The amount of strontium associated with the purified Sr-82 was determined by either: ICP-OES or method B which consisted of a summation of strontium quantified by gamma spectroscopy and ICP-MS. The summation method agreed within 10% to the ICP-OES for the total mass of strontium and the subsequent specific activities were determined to be 0.25–0.52 TBq mg-1. Method B was used to determine the isotope abundances by weight% of the purified Sr-82, and the abundances were: Sr-82 (10–20.7%), Sr-83 (0–0.05%), Sr-84 (35–48.5%), Sr-85 (16–25%), Sr-86 (12.5–23%), Sr-87 (0%), and Sr-88 (0–10%). The purified strontium contained mass amounts of Sr-82, Sr-84, Sr-85, Sr-86, and Sr-88 in abundances not associated with natural abundance, and 90% of the strontium was produced by the proton irradiation. A comparison of ICP-OES and method B for the analysis of Sr-82 indicated analysis by ICP-OES would be easier to determine total mass of strontium and comply with regulatory requirements. An ICP-OES analytical method for Sr-82 analysis was established and validated according to regulatory guidelines.

  9. Production of translationally cold barium monohalide ions

    CERN Document Server

    DePalatis, M V

    2013-01-01

    We have produced sympathetically cooled barium monohalide ions BaX$^+$ (X = F, Cl, Br) by reacting trapped, laser cooled Ba$^+$ ions with room temperature gas phase neutral halogen-containing molecules. Reaction rates for two of these (SF$_6$ and CH$_3$Cl) have been measured and are in agreement with classical models. BaX$^+$ ions are promising candidates for cooling to the rovibrational ground state, and our method presents a straightforward way to produce these polar molecular ions.

  10. Analysis of 26 Barium Stars I. Abundances

    CERN Document Server

    Allen, D M; Allen, Dinah M.; Barbuy, Beatriz

    2006-01-01

    We present a detailed analysis of 26 barium stars, including dwarf barium stars, providing their atmospheric parameters (Teff, log g, [Fe/H], vt) and elemental abundances. We aim at deriving gravities and luminosity classes of the sample stars, in particular to confirm the existence of dwarf barium stars. Accurate abundances of chemical elements were derived. Abundance ratios between nucleosynthetic processes, by using Eu and Ba as representatives of the r- and s-processes are presented. High-resolution spectra with the FEROS spectrograph at the ESO-1.5m Telescope, and photometric data with Fotrap at the Zeiss telescope at the LNA were obtained. The atmospheric parameters were derived in an iterative way, with temperatures obtained from colour-temperature calibrations. The abundances were derived using spectrum synthesis for Li, Na, Al, alpha-, iron peak, s- and r-elements atomic lines, and C and N molecular lines. Atmospheric parameters in the range 4300 < Teff < 6500, -1.2 < [Fe/H] < 0.0 and 1.4...

  11. Chemical abundances and kinematics of barium stars

    CERN Document Server

    de Castro, D B; Roig, F; Jilinski, E; Drake, N A; Chavero, C; Silva, J V Sales

    2016-01-01

    In this paper we present an homogeneous analysis of photospheric abundances based on high-resolution spectroscopy of a sample of 182 barium stars and candidates. We determined atmospheric parameters, spectroscopic distances, stellar masses, ages, luminosities and scale height, radial velocities, abundances of the Na, Al, $alpha$-elements, iron-peak elements, and s-process elements Y, Zr, La, Ce, and Nd. We employed the local-thermodynamic-equilibrium model atmospheres of Kurucz and the spectral analysis code {\\sc moog}. We found that the metallicities, the temperatures and the surface gravities for barium stars can not be represented by a single gaussian distribution. The abundances of $alpha$-elements and iron peak elements are similar to those of field giants with the same metallicity. Sodium presents some degree of enrichment in more evolved stars that could be attributed to the NeNa cycle. As expected, the barium stars show overabundance of the elements created by the s-process. By measuring the mean heav...

  12. Strontium Ions Substitution in Brushite Crystals: The Role of Strontium Chloride

    OpenAIRE

    2011-01-01

    The incorporation of strontium chloride to brushite cement was successful to introduce strontium ions within the lattice of brushite crystals. The effect of strontium ions on brushite cement properties was concentration dependent; such that, the addition of 5% and 10% (w/w) SrCl2 significantly increased the cement FST and the addition of 10% SrCl2 decreased the cement tensile strength. Further, cement weight loss was shown to be increased by cement modification with SrCl2. The combination of ...

  13. Barium peritonitis following upper gastrointestinal series: A case report

    Energy Technology Data Exchange (ETDEWEB)

    Ko, Su Jin; Hwang, Ji Young; Kim, Yong Jin; Hong, Seong Sook [Soonchunhyang University College of Medicine, Seoul Hospital, Seoul (Korea, Republic of)

    2017-06-15

    We report a rare case of barium peritonitis following an upper gastrointestinal (GI) series and its imaging findings in a 74-year-old female. Barium peritonitis is a rare but life-threatening complication of GI contrast investigation. Therefore, clinical awareness of barium peritonitis as a complication of GI tract contrast investigation would help to prevent such a complication and manage the patients properly.

  14. Enhanced Magnetic Trap Loading for Atomic Strontium

    CERN Document Server

    Barker, D S; Pisenti, N C; Campbell, G K

    2015-01-01

    We report on a technique to improve the continuous loading of atomic strontium into a magnetic trap from a Magneto-Optical Trap (MOT). This is achieved by adding a depumping laser tuned to the 3P1 to 3S1 (688-nm) transition. The depumping laser increases atom number in the magnetic trap and subsequent cooling stages by up to 65 % for the bosonic isotopes and up to 30 % for the fermionic isotope of strontium. We optimize this trap loading strategy with respect to the 688-nm laser detuning, intensity, and beam size. To understand the results, we develop a one-dimensional rate equation model of the system, which is in good agreement with the data. We discuss the use of other transitions in strontium for accelerated trap loading and the application of the technique to other alkaline-earth-like atoms.

  15. Enhanced magnetic trap loading for atomic strontium

    Science.gov (United States)

    Barker, D. S.; Reschovsky, B. J.; Pisenti, N. C.; Campbell, G. K.

    2015-10-01

    We report on a technique to improve the continuous loading of atomic strontium into a magnetic trap from a magneto-optical trap. This is achieved by adding a depumping laser tuned to the P31→S31 (688-nm) transition. The depumping laser increases atom number in the magnetic trap and subsequent cooling stages by up to 65% for the bosonic isotopes and up to 30% for the fermionic isotope of strontium. We optimize this trap loading strategy with respect to the 688-nm laser detuning, intensity, and beam size. To understand the results, we develop a one-dimensional rate equation model of the system, which is in good agreement with the data. We discuss the use of other transitions in strontium for accelerated trap loading and the application of the technique to other alkaline-earth-like atoms.

  16. History and challenges of barium titanate: Part I

    Directory of Open Access Journals (Sweden)

    Vijatović M.M.

    2008-01-01

    Full Text Available Barium titanate is the first ferroelectric ceramics and a good candidate for a variety of applications due to its excellent dielectric, ferroelectric and piezoelectric properties. Barium titanate is a member of a large family of compounds with the general formula ABO3 called perovskites. Barium titanate can be prepared using different methods. The synthesis method depends on the desired characteristics for the end application. The used method has a significant influence on the structure and properties of barium titanate materials. In this review paper, Part I contains a study of the BaTiO3 structure and frequently used synthesis methods.

  17. Thermochemical hydrogen production via a cycle using barium and sulfur: reaction between barium sulfide and water

    Energy Technology Data Exchange (ETDEWEB)

    Ota, K.; Conger, W.L.

    1977-01-01

    The reaction between barium sulfide and water, a reaction found in several sulfur based thermochemical cycles, was investigated kinetically at 653 to 866/sup 0/C. Gaseous products were hydrogen and hydrogen sulfide. The rate determining step for hydrogen formation was a surface reaction between barium sulfide and water. The rate of formation of hydrogen can be expressed as: RH2 = 1.07 x 10/sup -2/ exp (-3180/RT) (mol H/sub 2//mol BaS s). Hydrogen sulfide was produced during the initial period of reaction and the quantity of hydrogen sulfide formed during this period decreased as the temperature of reaction was increased.

  18. Enhanced Magnetic Trap Loading for Atomic Strontium

    OpenAIRE

    Barker, D.S.; Reschovsky, B. J.; Pisenti, N. C.; Campbell, G. K.

    2015-01-01

    We report on a technique to improve the continuous loading of atomic strontium into a magnetic trap from a Magneto-Optical Trap (MOT). This is achieved by adding a depumping laser tuned to the 3P1 to 3S1 (688-nm) transition. The depumping laser increases atom number in the magnetic trap and subsequent cooling stages by up to 65 % for the bosonic isotopes and up to 30 % for the fermionic isotope of strontium. We optimize this trap loading strategy with respect to the 688-nm laser detuning, int...

  19. First principles investigation of substituted strontium hexaferrite

    Science.gov (United States)

    Dixit, Vivek

    This dissertation investigates how the magnetic properties of strontium hexaferrite change upon the substitution of foreign atoms at the Fe sites. Strontium hexaferrite, SrFe12O19, is a commonly used hard magnetic material and is produced in large quantities (around 500,000 tons per year). For different applications of strontium hexaferrite, its magnetic properties can be tuned by a proper substitution of the foreign atoms. Experimental screening for a proper substitution is a cost-intensive and time-consuming process, whereas computationally it can be done more efficiently. We used the 'density functional theory' a first principles based method to study substituted strontium hexaferrite. The site occupancies of the substituted atoms were estimated by calculating the substitution energies of different configurations. The formation probabilities of configurations were used to calculate the magnetic properties of substituted strontium hexaferrite. In the first study, Al-substituted strontium hexaferrite, SrFe12-x AlxO19 with x=0.5 and x=1.0 were investigated. It was found that at the annealing temperature the non-magnetic Al +3 ions preferentially replace Fe+3 ions from the 12 k and 2a sites. We found that the magnetization decreases and the magnetic anisotropy field increases as the fraction, x of the Al atoms increases. In the second study, SrFe12-xGaxO19 and SrFe12-xInxO19 with x=0.5 and x=1.0 were investigated. In the case of SrFe12-xGaxO19, the sites where Ga+3 ions prefer to enter are: 12 k, 2a, and 4f1. For SrFe12-xInxO19, In+3 ions most likely to occupy the 12k, 4f1 , and 4f2 sites. In both cases the magnetization was found to decrease slightly as the fraction of substituted atom increases. The magnetic anisotropy field increased for SrFe12-xGaxO 19, and decreased for SrFe12-xInxO19 as the concentration of substituted atoms increased. In the third study, 23 elements (M) were screened for their possible substitution in strontium hexaferrite, SrFe12-xMxO 19

  20. Calcium and Strontium in Swedish Waters and Fish, and Accumulation of Strontium-90

    Energy Technology Data Exchange (ETDEWEB)

    Agnedal, P.O.

    1966-04-15

    The purpose of this study has been to investigate the correlation between calcium and strontium in fish in relation to the concentration of these elements in the water. An investigation of the uptake of strontium-90 has also been made and permissible levels of strontium-90 in the water is calculated based upon the uptake in fish muscle tissues. Lakes with calcium concentrations between 2 - 63 mg/l have been studied and samples from the Baltic coastal water are also included. Three fish species are studied, viz. pike (Esox lucius (L.)), perch (Perca fluviatilis (L.)) and roach (Leuciscus rutilus (L.)). Bones, muscle tissues and skin + scales have been analysed. Strontium-90 measurements have been made showing an increase in both water and fish. Calculations show that in water with about 2 mg Ca/l a 10-fold increase of the existing strontium-90 level might give strontium-90 concentrations in fish muscle tissues close to what is permissible. In lakes with calcium concentrations 20 - 40 mg/l the permissible levels for drinking water will be exceeded before the fish consumption would have to be restricted.

  1. Three-dimensional labeling of newly formed bone using synchrotron radiation barium K-edge subtraction imaging

    Science.gov (United States)

    Panahifar, Arash; Swanston, Treena M.; Pushie, M. Jake; Belev, George; Chapman, Dean; Weber, Lynn; Cooper, David M. L.

    2016-07-01

    Bone is a dynamic tissue which exhibits complex patterns of growth as well as continuous internal turnover (i.e. remodeling). Tracking such changes can be challenging and thus a high resolution imaging-based tracer would provide a powerful new perspective on bone tissue dynamics. This is, particularly so if such a tracer can be detected in 3D. Previously, strontium has been demonstrated to be an effective tracer which can be detected by synchrotron-based dual energy K-edge subtraction (KES) imaging in either 2D or 3D. The use of strontium is, however, limited to very small sample thicknesses due to its low K-edge energy (16.105 keV) and thus is not suitable for in vivo application. Here we establish proof-of-principle for the use of barium as an alternative tracer with a higher K-edge energy (37.441 keV), albeit for ex vivo imaging at the moment, which enables application in larger specimens and has the potential to be developed for in vivo imaging of preclinical animal models. New bone formation within growing rats in 2D and 3D was demonstrated at the Biomedical Imaging and Therapy bending magnet (BMIT-BM) beamline of the Canadian Light Source synchrotron. Comparative x-ray fluorescence imaging confirmed those patterns of uptake detected by KES. This initial work provides a platform for the further development of this tracer and its exploration of applications for in vivo development.

  2. Fixation of Radioactive Strontium in Soil

    DEFF Research Database (Denmark)

    Gregers-Hansen, Birte

    1964-01-01

    The contamination of agricultural areas by fission products from nuclear events is a possibility, and would in turn lead to contamination of plants. Of special importance is the long-lived strontium-90, as it has been shown1 that this isotope is taken up by plants to a much greater extent than an...

  3. Cesium and Strontium Separation Technologies Literature Review

    Energy Technology Data Exchange (ETDEWEB)

    T. A. Todd; T. A. Todd; J. D. Law; R. S. Herbst

    2004-03-01

    Integral to the Advanced Fuel Cycle Initiative (AFCI) Program’s proposed closed nuclear fuel cycle, the fission products cesium and strontium in the dissolved spent nuclear fuel stream are to be separated and managed separately. A comprehensive literature survey is presented to identify cesium and strontium separation technologies that have the highest potential and to focus research and development efforts on these technologies. Removal of these high-heat-emitting fission products reduces the radiation fields in subsequent fuel cycle reprocessing streams and provides a significant short-term (100 yr) heat source reduction in the repository. This, along with separation of actinides, may provide a substantial future improvement in the amount of fuel that could be stored in a geologic repository. The survey and review of the candidate cesium and strontium separation technologies are presented herein. Because the AFCI program intends to manage cesium and strontium together, technologies that simultaneously separate both elements are of the greatest interest, relative to technologies that separate only one of the two elements.

  4. Dielectric and impedance behavior of neodymium substituted strontium hexaferrite

    Science.gov (United States)

    Bhat, Bilal Hamid; Samad, Rubiya; Want, Basharat

    2016-09-01

    In this study, dielectric behavior and complex impedance of neodymium (Nd) substituted strontium hexaferrite system: Sr1- x Nd x Fe12O19 ( x = 0.0, 0.05, 0.1, 0.15, 0. 20), synthesized by citrate precursor technique, have been evaluated as a function of applied frequency and temperature. Variation of dielectric constant and dielectric loss with frequency shows the identical behavior for all the compositions. The value of dielectric constant increases with Nd doping. Relaxation process is observed in the composition x = 0.20, and the peaks in this composition shift toward the higher-frequency region as the temperature increases. The dielectric constants show temperature-independent behavior at low temperature, whereas at higher temperatures it increases for all the frequencies. The AC conductivity follows Jonscher's power law, showing that conduction mechanism is due to polaron hopping. Complex impedance as a function of composition and temperature is used to examine the role of grain and grain boundary in the prepared material. Cole-cole plot shows only one semicircle up to x = 0.15, while as for x = 0.20 two semicircles are observed. The conduction mechanism is explained on the basis of both grain and grain boundary.

  5. Dielectric and impedance behavior of neodymium substituted strontium hexaferrite

    Energy Technology Data Exchange (ETDEWEB)

    Bhat, Bilal Hamid; Samad, Rubiya; Want, Basharat [University of Kashmir, Solid State Research Lab., Department of Physics, Srinagar (India)

    2016-09-15

    In this study, dielectric behavior and complex impedance of neodymium (Nd) substituted strontium hexaferrite system: Sr{sub 1-x}Nd{sub x}Fe{sub 12}O{sub 19} (x = 0.0, 0.05, 0.1, 0.15, 0.20), synthesized by citrate precursor technique, have been evaluated as a function of applied frequency and temperature. Variation of dielectric constant and dielectric loss with frequency shows the identical behavior for all the compositions. The value of dielectric constant increases with Nd doping. Relaxation process is observed in the composition x = 0.20, and the peaks in this composition shift toward the higher-frequency region as the temperature increases. The dielectric constants show temperature-independent behavior at low temperature, whereas at higher temperatures it increases for all the frequencies. The AC conductivity follows Jonscher's power law, showing that conduction mechanism is due to polaron hopping. Complex impedance as a function of composition and temperature is used to examine the role of grain and grain boundary in the prepared material. Cole-cole plot shows only one semicircle up to x = 0.15, while as for x = 0.20 two semicircles are observed. The conduction mechanism is explained on the basis of both grain and grain boundary. (orig.)

  6. INFLUENCE OF BARIUM OXIDE ADDITIONS ON PORTLAND CLINKER

    Directory of Open Access Journals (Sweden)

    Anezka Zezulova

    2016-12-01

    Full Text Available Nowadays, nuclear power plants are widespread around the world and research is of great interest. Together with nuclear research, shielding of different types of radiation is an important current topic of research aiming at their safety. Portland cement has been an elementary building material for centuries. Since barium is very efficient in shielding different types of radiation, it can be assumed that the radiation shielding capability of cement can be improved by incorporation of barium. This work deals with the influence of barium oxide, added in the form of barium carbonate and sulphate, on the formation and properties of Portland clinker. The structure of burnt clinkers and the ratio of clinker phases were studied by polarizing microscopy and by X-ray diffraction. With increasing barium content, the alite-belite ratio decreases and the content of free lime gradually increases. Moreover, sulphates induce the growth of alite crystals. The ability of barium to be a part of the clinker minerals was observed by scanning electron microscopy. Belite and clinker melt contain the highest amount of barium, but aggregates of barium oxide are formed in the clinker melt. Furthermore, the rate of alite crystallization was studied under isothermal conditions.

  7. Barium enema findings of milk allergy in infants

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Gyoung Ju; Kim, Mi Jeong; Lee, Hee Jung [Keimyung University School of Medicine, Daegu (Korea, Republic of)

    2006-09-15

    We wanted to evaluate the barium enema findings of milk allergy in infants. Retrospective evaluation of the plain abdominal radiography and barium enema findings was performed in fifteen young infants suffering with milk allergy. The presence of gaseous distension, rectal gas, paralytic ileus and mechanical obstruction was evaluated on the plain radiography. The presence of spasm, a transitional zone, a reversed rectosigmoid index and mucosal irregularity was analyzed on the barium enema; the presence of barium retention was also evaluated on 24-hour-delayed plain radiography. Paralytic ileus was the most common finding on the plain radiography (93%). On the barium enema, continuous spasm of the colon, ranging from the rectum to the descending colon, was revealed in ten infants (67%). A transitional zone was observed in one infant and a reversed rectosigmoid index was revealed in four. Mucosal irregularity was observed in two infants. Barium retention was demonstrated in 11 of fifteen cases: throughout the entire colon (n = 3), from the rectum to the descending colon (n = 7), and up to the transverse colon (n = 1). The most common barium enema finding of milk allergy in infants was spasm of the distal colon. The other findings were a transitional zone, a reversed rectosigmoid index, mucosal irregularity and barium retention.

  8. [Silica, aluminum, iron, sulfur, and barium in a urinary calculus].

    Science.gov (United States)

    Rodríguez-Miñón Cifuentes, J L; Salvador, E; Bellanato, J; Medina, J A

    1994-05-01

    Presentation of the analytical results by Sweep Microscopy of a small papillary calculus spontaneously eliminated after a nephritic colic. The main component is monohydrate calcium oxalate. When the stone core was analyzed with EDAX, silica, aluminium, iron, sulphur and barium were detected. The origin of these elements is discussed and the presence of barium emphasized as exceptional.

  9. Scattering lengths of calcium and barium isotopes

    Energy Technology Data Exchange (ETDEWEB)

    Dammalapati, U.; Willmann, L.; Knoop, S. [Kernfysisch Versneller Instituut (KVI), University of Groningen, Zernikelaan 25, 9747 AA Groningen (Netherlands); LaserLaB Vrije Universiteit, De Boelelaan 1081, 1081 HV Amsterdam (Netherlands)

    2011-11-15

    We have calculated the s-wave scattering length of all the even isotopes of calcium (Ca) and barium (Ba) in order to investigate the prospect of Bose-Einstein condensation (BEC). For Ca we have used an accurate molecular potential based on detailed spectroscopic data. Our calculations show that Ca does not provide other isotopes alternative to the recently Bose condensed {sup 40}Ca that suffers strong losses because of a very large scattering length. For Ba we show by using a model potential that the even isotopes cover a broad range of scattering lengths, opening the possibility of BEC for at least one of the isotopes.

  10. Europium-doped barium bromide iodide

    Energy Technology Data Exchange (ETDEWEB)

    Gundiah, Gautam; Hanrahan, Stephen M.; Hollander, Fredrick J.; Bourret-Courchesne, Edith D.

    2009-10-21

    Single crystals of Ba0.96Eu0.04BrI (barium europium bromide iodide) were grown by the Bridgman technique. The title compound adopts the ordered PbCl2 structure [Braekken (1932). Z. Kristallogr. 83, 222-282]. All atoms occupy the fourfold special positions (4c, site symmetry m) of the space group Pnma with a statistical distribution of Ba and Eu. They lie on the mirror planes, perpendicular to the b axis at y = +-0.25. Each cation is coordinated by nine anions in a tricapped trigonal prismatic arrangement.

  11. Barium appendicitis: A single institution review in Japan

    Science.gov (United States)

    Katagiri, Hideki; Lefor, Alan Kawarai; Kubota, Tadao; Mizokami, Ken

    2016-01-01

    AIM To review clinical experience with barium appendicitis at a single institution. METHODS A retrospective review of patients admitted with a diagnosis of acute appendicitis, from January 1, 2013 to December 31, 2015 was performed. Age, gender, computed tomography (CT) scan findings if available, past history of barium studies, pathology, and the presence of perforation or the development of complications were reviewed. If the CT scan revealed high density material in the appendix, the maximum CT scan radiodensity of the material is measured in Hounsfield units (HU). Barium appendicitis is defined as: (1) patients diagnosed with acute appendicitis; (2) the patient has a history of a prior barium study; and (3) the CT scan shows high density material in the appendix. Patients who meet all three criteria are considered to have barium appendicitis. RESULTS In total, 396 patients were admitted with the diagnosis of acute appendicitis in the study period. Of these, 12 patients (3.0%) met the definition of barium appendicitis. Of these 12 patients, the median CT scan radiodensity of material in the appendix was 10000.8 HU, ranging from 3066 to 23423 HU (± 6288.2). In contrast, the median CT scan radiodensity of fecaliths in the appendix, excluding patients with barium appendicitis, was 393.1 HU, ranging from 98 to 2151 HU (± 382.0). The CT scan radiodensity of material in the appendices of patients with barium appendicitis was significantly higher than in patients with nonbarium fecaliths (P < 0.01). CONCLUSION Barium appendicitis is not rare in Japan. Measurement of the CT scan radiodensity of material in the appendix may differentiate barium appendicitis from routine appendicitis.

  12. The Novel Formation of Barium Titanate Nanodendrites

    Directory of Open Access Journals (Sweden)

    Chien-Jung Huang

    2014-01-01

    Full Text Available The barium titanate (BaTiO3 nanoparticles with novel dendrite-like structures have been successfully fabricated via a simple coprecipitation method, the so-called BaTiO3 nanodendrites (BTNDs. This method was remarkable, fast, simple, and scalable. The growth solution is prepared by barium chloride (BaCl2, titanium tetrachloride (TiCl4, and oxalic acid. The shape and size of BaTiO3 depend on the amount of added BaCl2 solvent. To investigate the influence of amount of BaCl2 on BTNDs, the amount of BaCl2 was varied in the range from 3 to 6 mL. The role of BaCl2 is found to have remarkable influence on the morphology, crystallite size, and formation of dendrite-like structures. The thickness and length of the central stem of BTND were ~300 nm and ~20 μm, respectively. The branchings were found to occur at irregular intervals along the main stem. Besides, the formation mechanism of BTND is proposed and discussed.

  13. NANOSCALE BARIUM HYDROSILICATES: CHOOSING THE SYNTHESIS TECHNOLOGY

    Directory of Open Access Journals (Sweden)

    GRISHINA Anna Nikolaevna

    2013-08-01

    Full Text Available Cement concretes are the most used materials in modern civil engineering. Due to that such materials draw great attention both in the Russian Federation and abroad. The possibility to enhance the manufacturability and operational properties of concretes results in significant reduction of overall operating costs. Many enhancement methods have been elaborated. Among them there is one based on introduction of calcium hydrosilicates into construction composition. The authors set up a hypothesis that similarity between properties and structures of different hydrosilicates (for example, alkaline earth metals and metals of the second group will provide similar increased operational characteristics. The specialists of Research and Educational Center «Nanotechnology» are developing cement composites nanomodification methods which include introduction of nanodimensional barium hydrosilicates particles. The synthesis of barium hydrosilicates particles can be done with the use of many technologies, different by energy consumption or performing complexity. Taking into account both these factors, one can assume that low-temperature sol-gel synthesis from diluted water solutions is the proper technology. The present paper shows that this assumption is correct. The selection of certain technology is made by the means of multiobjective optimization, which is in turn is performed by the means of linear scalarization. This method, while not always giving the Pareto optimal solutions, can be easily implemented. The particle size distribution is taken into consideration during selection of objectives and weights. It is shown that selected technology allows manufacturing nanoparticles with median size about 30 nm.

  14. Dopant Behaviours of Sm2O3 on Microstructure and Properties of Barium Zirconium Titanate Ceramics

    Institute of Scientific and Technical Information of China (English)

    王永力; 李龙土; 齐建全; 桂治轮

    2001-01-01

    The effect of Sm2O3-dopant on the sintering characteristics and dielectric properties of barium zirconium titanate ceramics (BaZrxTi1-xO3) was investigated. It is shown that trace amount of Sm2O3 can greatly affect the grain growth and densification of barium zirconium titanate ceramics during sintering. At the same time, the dielectric peak at high temperature shifts to lower temperature and that at low temperature shifts to higher temperature. The two dielectric peaks overlap with each other when the Sm2O3-dopant content varies from 0.25% to 1%, and the maximum relative dielectric constant is greatly enhanced. These effects may be attributed to the substitution actions of the rare earth element in perovskite lattice. At the doping content of 0.75%, the dielectric constant maximum of 23570 can be obtained. By adopting some proper additives, an excellent Y5V dielective material is obtained, and the room temperature properties are as follows: relative dielectric constant εRT≥23,000, dielectric loss tgδ≤0.0075 and the breakdown strength under alternating field Eb≥5 kV·mm-1.

  15. A novel solvothermal route for obtaining strontium titanate nanoparticles

    Energy Technology Data Exchange (ETDEWEB)

    Marquez-Herrera, A., E-mail: alfredo.marquez@uaslp.mx [Universidad Autonoma de San Luis Potosi, Departamento de Ingenieria Mecanica Administrativa, Coordinacion Academica Region Altiplano (COARA) (Mexico); Ovando-Medina, Victor M.; Corona-Rivera, Miguel A. [Universidad Autonoma de San Luis Potosi, Departamento de Ingenieria Quimica, Coordinacion Academica Region Altiplano (COARA) (Mexico); Hernandez-Rodriguez, E.; Zapata-Torres, M. [Centro de Investigacion en Ciencia Aplicada y Tecnologia Avanzada, Unidad Legaria IPN (Mexico); Campos-Gonzalez, E.; Guillen-Cervantes, A.; Zelaya-Angel, O.; Melendez-Lira, M. [CINVESTAV-IPN, Departamento de Fisica (Mexico)

    2013-04-15

    Strontium titanate (SrTiO{sub 3}) has attracted a lot of attention because of its possible applications in new microelectronic devices. It is a material with a high dielectric constant, low leakage current, and some of its properties can be changed by adding or modifying the concentration of a dopant, which can be used for a wide range of functional purposes, from simple capacitors to complicated microwave devices. Therefore, in this work, we report the development of a new route to synthesize SrTiO{sub 3} nanoparticles based on the solvothermal method by employing two precursor solutions: strontium chloride and titanium(IV) butoxide. Our route allows the production of cubic SrTiO{sub 3} nanoparticles with a narrow size distribution. The particle sizes range between 8 and 24 nm, forming agglomerates of SrTiO{sub 3} in the range of 128-229 nm. It was demonstrated that the Ti/Sr molar ratio employed into the precursor solution has an important effect onto the chemical composition of the resulting SrTiO{sub 3} nanoparticles: when using Ti/Sr < 1, the formation and incorporation of the SrCO{sub 3} compound into the nanoparticles was observed while with Ti/Sr {>=} 1 nanoparticles are free of contaminants. The as-prepared nanoparticles were characterized by energy-dispersive X-ray spectroscopy, X-ray diffraction, transmission electron microscopy, high-resolution TEM, selected area electron diffraction, scanning electron microscopy, and dynamic light scattering.

  16. Growth and characterization of barium oxide nanoclusters on YSZ(111)

    Energy Technology Data Exchange (ETDEWEB)

    Nachimuthu, Ponnusamy; Kim, Yong Joo; Kuchibhatla, Satyanarayana V N T; Yu, Zhongqing; Jiang, Weilin; Engelhard, Mark H.; Shutthanandan, V.; Szanyi, Janos; Thevuthasan, Suntharampillai

    2009-08-13

    Barium oxide (BaO) was grown on YSZ(111) substrate by oxygen-plasma-assisted molecular beam epitaxy (OPA-MBE). In-situ reflection high-energy electron diffraction, ex-situ x-ray diffraction, atomic force microscopy and x-ray photoelectron spectroscopy have confirmed that the BaO grows as clusters on YSZ(111). During and following the growth under UHV conditions, BaO remains in single phase. When exposed to ambient conditions, the clusters transformed to BaCO3 and/or Ba(OH)2 H2O. However, in a few attempts of BaO growth, XRD results show a fairly single phase cubic BaO with a lattice constant of 0.5418(1) nm. XPS results show that exposing BaO clusters to ambient conditions results in the formation BaCO3 on the surface and partly Ba(OH)2 throughout in the bulk. Based on the observations, it is concluded that the BaO nanoclusters grown on YSZ(111) are highly reactive in ambient conditions. The variation in the reactivity of BaO between different attempts of the growth is attributed to the cluster size.

  17. Review on dielectric properties of rare earth doped barium titanate

    Science.gov (United States)

    Ismail, Fatin Adila; Osman, Rozana Aina Maulat; Idris, Mohd Sobri

    2016-07-01

    Rare earth doped Barium Titanate (BaTiO3) were studied due to high permittivity, excellent electrical properties and have wide usage in various applications. This paper reviewed on the electrical properties of RE doped BaTiO3 (RE: Lanthanum (La), Erbium (Er), Samarium (Sm), Neodymium (Nd), Cerium (Ce)), processing method, phase transition occurred and solid solution range for complete study. Most of the RE doped BaTiO3 downshifted the Curie temperature (TC). Transition temperature also known as Curie temperature, TC where the ceramics had a transition from ferroelectric to a paraelectric phase. In this review, the dielectric constant of La-doped BaTiO3, Er-doped BaTiO3, Sm-doped BaTiO3, Nd-doped BaTiO3 and Ce-doped BaTiO3 had been proved to increase and the transition temperature or also known as TC also lowered down to room temperature as for all the RE doped BaTiO3 except for Er-doped BaTiO3.

  18. Defect Chemistry and Microstructure of Complex Perovskite Barium Zinc Niobate

    Science.gov (United States)

    Peng, Ping

    1991-02-01

    This dissertation presents a systematic study of the characterization of the phase transitions, microstructures, defects and transport properties of undoped and doped complex perovskite barium zinc niobate (BZN). Complex perovskite BZN is a paraelectric material while its parent material barium titanate is ferroelectric. With codoping of (Zn + 2Nb) into Ti site, BaTiO_3 shows three distinguished features. First, the Curie temperature is lowered; second, the three phase transitions (cubic-tetragonal-orthorhombic-rhombohedral) coalesce; and lastly, the transition becomes diffuse showing a typical 2nd order phase transition compared with 1st order in undoped BaTiO_3. Complex microchemical ordering is another characteristic of BZN. Stoichiometric BZN shows a mixture of two types of ordering schemes. 1:1, 1:2 ordered microdomains and the disordered matrix co-exist. The 1:1 type ordering involves an internal charge imbalance which inhibits the growth of 1:1 type of ordered microdomains. The 1:2 type ordering is consistent with the chemical composition of BZN. These ordering patterns can be modified by either adjustment of the Zn/Nb ratio or by doping. The defect structure of the stoichiometric BZN is closely related to that of BaTiO_3. Stoichiometric BZN is an insulator with wide band gap (~ 3.70 eV). Undoped BZN has a high oxygen vacancy concentration which comes from three possible sources, such as unavoidable acceptor impurities, due to their natural abundance, Zn/Nb ratio uncertainty due to processing limitations, and high temperature ZnO loss due to sintering process. The oxygen vacancy concentration for undoped BZN lays in the neighborhood of 1500 ppm (atm.). The compensation defects for various dopants have also been identified. Both electrons and holes conduct by a small polaron mechanism. Various thermodynamic parameters, such as enthalpies of oxidation and reduction, mass action constants for intrinsic electronic disorder, oxidation and reduction have been

  19. Strengthening mechanism of steels treated by barium-bearing alloys

    Institute of Scientific and Technical Information of China (English)

    Zhouhua Jiang; Yang Liu

    2008-01-01

    The deoxidation, desulfurization, dephosphorization, microstructure, and mechanical properties of steels treated by barium-bearing alloys were investigated in laboratory and by industrial tests. The results show that barium takes part in the deoxidation reaction at the beginning of the experiments, generating oxide and sulfide compound inclusions, which easily float up from the molten steel, leading to the rapid reduction of total oxygen content to a very low level. The desulfurization and dephosphorization capabilities of calcium-bearing alloys increase with the addition of barium. The results of OM and SEM observations and mechanical property tests show that the structure of the steel treated by barium-bearing alloys is refined remarkably, the iamellar thickness of pearlitic structure decreases, and the pearlitic morphology shows clustering distribution. Less barium exists in steel substrate and the enrichment of barium-bearing precipitated phase mostly occurs in grain boundary and phase boundary, which can prevent the movement of grain boundary and dislocation during the heat treatment and the deformation processes. Therefore, the strength and toughness of barium-treated steels are improved by the effect of grain-boundary strengthening and nail-prick dislocation.

  20. Strontium isotope stratigraphy of the Pelotas Basin

    Energy Technology Data Exchange (ETDEWEB)

    Zerfass, Geise de Santana dos Anjos, E-mail: geise.zerfass@petrobras.com.br [Petroleo Brasileiro S.A. (PETROBRAS/CENPES/PDGEO/BPA), Rio de Janeiro, RJ (Brazil). Centro de Pesquisas e Desenvolvimento Leopoldo Americo Miguez de Mello; Chemale Junior, Farid, E-mail: fchemale@unb.br [Universidade de Brasilia (UnB), DF (Brazil). Instituto de Geociencias; Moura, Candido Augusto Veloso, E-mail: candido@ufpa.br [Universidade Federal do Para (UFPA), Belem, PA (Brazil). Centro de Geociencias. Dept. de Geoquimica e Petrologia; Costa, Karen Badaraco, E-mail: karen.costa@usp.br [Instituto Oceanografico, Sao Paulo, SP (Brazil); Kawashita, Koji, E-mail: koji@usp.br [Unversidade de Sao Paulo (USP), SP (Brazil). Centro de Pesquisas Geocronologicas

    2014-07-01

    Strontium isotope data were obtained from foraminifera shells of the Pelotas Basin Tertiary deposits to facilitate the refinement of the chronostratigraphic framework of this section. This represents the first approach to the acquisition of numerical ages for these strata. Strontium isotope stratigraphy allowed the identification of eight depositional hiatuses in the Eocene-Pliocene section, here classified as disconformities and a condensed section. The reconnaissance of depositional gaps based on confident age assignments represents an important advance considering the remarkably low chronostratigraphic resolution in the Cenozoic section of the Pelotas Basin. The recognition of hiatuses that match hiatuses is based on biostratigraphic data, as well as on global events. Furthermore, a substantial increase in the sedimentation rate of the upper Miocene section was identified. Paleotemperature and productivity trends were identified based on oxygen and carbon isotope data from the Oligocene-Miocene section, which are coherent with worldwide events, indicating the environmental conditions during sedimentation. (author)

  1. Phase Stability of the Lanthanum Strontium Manganites

    Science.gov (United States)

    Zheng, Feng; Pederson, Larry

    1996-03-01

    Phase diagram and thermodynamic data of the La-Sr-Mn-O system has been studied. The ABO3 -type perovskite of this system is presently the preferred cathode material for application in solid oxide fuel cells. And the phase stability of the lanthanum strontium manganites at elevated temperature is vital to fuel cell operation. Measuring the electromotive force through solid galvanic cell (-) Air,Pt|SrF_2,SrO||CaF_2||La_1-xSr_xMnO_3,SrF_2|Pt,Air (+) and the like enable us to derive the strontium oxide activity and other thermodynamic parameters such as Gibbs free energy of reaction, etc, which help us to understand the materials in using.

  2. Laser Stabilization with Laser Cooled Strontium

    DEFF Research Database (Denmark)

    Christensen, Bjarke Takashi Røjle

    the nonlinear effects from coupling of an optical cavity to laser cooled atoms having a narrow transition linewidth. Here, we have realized such a system where a thermal sample of laser cooled strontium-88 atoms are coupled to an optical cavity. The strontium-88 atoms were probed on the narrow 1S0-3P1 inter......The frequency stability of current state-of-the-art stabilized clock lasers are limited by thermal fluctuations of the ultra-stable optical reference cavities used for their frequency stabilization. In this work, we study the possibilities for surpassing this thermal limit by exploiting......-combination line at 689 nm in a strongly saturated regime. The dynamics of the atomic induced phase shift and absorption of the probe light were experimentally studied in details with the purpose of applications to laser stabilization. The atomic sample temperature was in the mK range which brought this system out...

  3. Growth and characterization of strontium tartrate pentahydrate crystals

    Energy Technology Data Exchange (ETDEWEB)

    Firdous, A.; Ahmad, M.M. [Department of Physics, National Institute of Technology, Kashmir (India); Quasim, I.; Kotru, P.N. [Crystal Growth and Materials Research Laboratory, Department of Physics and Electronics, University of Jammu (India)

    2008-10-15

    Silica gel impregnated with L-tartaric acid and using strontium nitrate as the second reactant leads to the growth of well faceted strontium tartrate pentahydrate single crystals.The morphological developmen and internal cell dimensions are observed to be different from the ones reported in the literature for strontium tartrate trihydrate crystals. The crystals are characterized using XRD, CH analysis, SEM, FTIR spectroscopy and thermoanalytical techniques. The crystals are observed to be thermally stable upto about 105 C but thereafter start decomposing and ejecting water of hydration at various stages, finally reducing to strontium oxide. (copyright 2008 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (orig.)

  4. Strontium ranelate in postmenopausal osteoporosis treatment: a critical appraisal

    Directory of Open Access Journals (Sweden)

    Roberto Cesareo

    2009-12-01

    Full Text Available Roberto Cesareo1, Clemente Napolitano1, Mario Iozzino21Department of Internal Medicine, 2Department of Radiology, S.M. Goretti Hospital, Latina, ItalyAbstract: Osteoporosis is a progressive and debilitating disease characterized by a massive bone loss with a deterioration of bone tissues, and a propensity for a fragility fracture. Strontium ranelate is the first antiosteoporotic treatment that has dual mode of action and simultaneously increases bone formation, while decreasing bone resorption, thus rebalancing bone turnover formation. Strontium ranelate rebalances bone turnover in favor of improved bone geometry, cortical thickness, trabecular bone morphology and intrinsic bone tissue quality, which translates into enhanced bone strength. This review describes the mechanism of the strontium ranelate action and its effects on bone mineral density, bone turnover, and osteoporotic fractures. The efficacy of strontium ranelate in postmenopausal osteoporosis treatment to reduce the risk of vertebral and hip fractures has been highlighted in several randomized, controlled trials. Treatment efficacy with strontium ranelate has been documented across a wide range of patient profiles: age, number of prevalent vertebral fractures, body mass index, and a family history of osteoporosis. Because strontium ranelate has a large spectrum of efficacy, it can be used to treat different subgroups of patients with postmenopausal osteoporosis. Strontium ranelate was shown to be relatively well tolerated and the safety aspects were good. Strontium ranelate should be considered as a first-line treatment for postmenopausal osteoporotic patients.Keywords: osteoporosis, strontium ranelate, therapy

  5. Synthesis of Strontium Carbonate by the Induction of Microbiology

    Institute of Scientific and Technical Information of China (English)

    HUO Ji-Chuan; LIU Shu-Xin; WANG Li-Na; LEI Hong

    2012-01-01

    Spherical strontium carbonate was synthesized by the induction of microbial bacillus pasteurii at ambient temperature with strontium chloride and urea as the raw materials. The phase composition, particle size and morphology of the product were studied by XRD and SEM. The results indicated that the strontium carbonate synthesized by the induction of microbial bacillus pasteurii was of good dispersion and uniform particle size. The spherical strontium carbonate particles obtained by adding different control agents were constructed by numerous flakes or olive-shaped nano-particles. The products were orthorhombic according to their XRD patterns.

  6. Ceria and strontium titanate based electrodes

    DEFF Research Database (Denmark)

    2010-01-01

    A ceramic anode structure obtainable by a process comprising the steps of: (a) providing a slurry by dispersing a powder of an electronically conductive phase and by adding a binder to the dispersion, in which said powder is selected from the group consisting of niobium-doped strontium titanate, ......) with the precursor solution of step (c),(e) subjecting the resulting structure of step (d) to calcination, and (f) conducting steps (d)-(e) at least once....

  7. Eu2+ luminescence in strontium aluminates

    NARCIS (Netherlands)

    Dutczak, D.; Juestel, T.; Ronda, C.; Meijerink, A.

    2015-01-01

    The luminescence properties of Eu2+ doped strontium aluminates are reported and reviewed for a variety of aluminates, viz. SrAl12O19, SrAl4O7, Sr4Al14O25, SrAl2O4 and Sr3Al2O6. The aim of the research is to investigate the role of local coordination and covalency of the aluminate host lattice,

  8. Eu2+ luminescence in strontium aluminates

    NARCIS (Netherlands)

    Dutczak, D.; Juestel, T.; Ronda, C.; Meijerink, A.

    2015-01-01

    The luminescence properties of Eu2+ doped strontium aluminates are reported and reviewed for a variety of aluminates, viz. SrAl12O19, SrAl4O7, Sr4Al14O25, SrAl2O4 and Sr3Al2O6. The aim of the research is to investigate the role of local coordination and covalency of the aluminate host lattice, relat

  9. First Principles Investigation of Fluorine Based Strontium Series of Perovskites

    Science.gov (United States)

    Erum, Nazia; Azhar Iqbal, Muhammad

    2016-11-01

    Density functional theory is used to explore structural, elastic, and mechanical properties of SrLiF3, SrNaF3, SrKF3 and SrRbF3 fluoroperovskite compounds by means of an ab-initio Full Potential-Linearized Augmented Plane Wave (FP-LAPW) method. Several lattice parameters are employed to obtain accurate equilibrium volume (Vo). The resultant quantities include ground state energy, elastic constants, shear modulus, bulk modulus, young's modulus, cauchy's pressure, poisson's ratio, shear constant, ratio of elastic anisotropy factor, kleinman's parameter, melting temperature, and lame's coefficient. The calculated structural parameters via DFT as well as analytical methods are found to be consistent with experimental findings. Chemical bonding is used to investigate corresponding chemical trends which authenticate combination of covalent-ionic behavior. Furthermore electron density plots as well as elastic and mechanical properties are reported for the first time which reveals that fluorine based strontium series of perovskites are mechanically stable and posses weak resistance towards shear deformation as compared to resistance towards unidirectional compression while brittleness and ionic behavior is dominated in them which decreases from SrLiF3 to SrRbF3. Calculated cauchy's pressure, poisson's ratio and B/G ratio also proves ionic nature in these compounds. The present methodology represents an effective and influential approach to calculate the whole set of elastic and mechanical parameters which would support to understand various physical phenomena and empower device engineers for implementing these materials in numerous applications.

  10. Laser-Excited Fluorescence Spectra of Strontium Monoiodide.

    Science.gov (United States)

    Bernard; Effantin; d'incan; Topouzkhanian; Wannous

    1999-05-01

    Fluorescence spectra of strontium monoiodide excited by Ar++ and Kr+ laser lines have been analyzed by Fourier transform spectrometry. Rotational levels have been populated either directly or after collisional relaxation: (i) in D2Sigma+ (v = 0, 1) by ultraviolet lines of Ar++, inducing numerous fluorescence transitions ending in the levels v = 0-3 of the strongly interacting A2Pi and B2Sigma+ states, (ii) in A2Pi3/2 (v = 0-4) by Kr+ line at 676.44 nm, de-exciting into transitions to X2Sigma+ (v = 0-6). Deperturbed constants for A2Pi and B2Sigma+ states and A approximately B interaction parameter are calculated from the numerical treatment of D2Sigma+ (v = 0, 1) --> A2Pi (v = 0-3) approximately B2Sigma+ (v = 0-3) transitions. Rotational constants for D2Sigma+ (v = 0, 1) are obtained for the first time. The wavenumbers of some 670 fluorescence lines are cataloged. Copyright 1999 Academic Press.

  11. Barium concentration in grain of Aegilops and Triticum species

    Directory of Open Access Journals (Sweden)

    Denčić Srbislav S.

    2015-01-01

    Full Text Available The aim of this study was to evaluate the concentration of barium in grain of various Aegilops and Triticum species with different genomes. The studied species differed significantly with respect to the concentration of barium. The grain of wild diploid Aegilops speltoides, the donor of B genome, contained significantly higher Ba concentration than all other analyzed genotypes. Wild and cultivated tetraploid wheats (Triticum diciccoides, Triticum dicoccon, Triticum turgidum and Triticum durum had the lowest Ba concentration in grain. The modern cultivated hexaploid varieties presented substantial variation in grain concentration of barium. The highest Ba concentration (3.42 mg/kg occurred in Serbian winter wheat variety Panonnia.

  12. Analysis of europium doped luminescent barium thioaluminate

    Institute of Scientific and Technical Information of China (English)

    张东璞; 喻志农; 薛唯; 章婷; 丁瞾; 王武育

    2010-01-01

    Europium-doped barium thioaluminate sputtering target was synthesized by powder sintering method and thin film was deposited by radio frequency(RF) sputtering.X-ray diffractometer(XRD) pattern indicated that the main compound of the target was BaAl4S7.Oxygen was the main impurity which led to the formation of BaAl2O4.It was shown that both BaAl4S7 and BaAl2S4 were contained in the as-grown thin films and a 471.7 nm emission peak in the PL spectra appeared due to a combination of BaAl4S7:Eu2+ and BaAl2S4:Eu2...

  13. Chemical abundance analysis of 19 barium stars

    CERN Document Server

    Yang, G C; Spite, M; Chen, Y Q; Zhao, G; Zhang, B; Liu, G Q; Liu, Y J; Liu, N; Deng, L C; Spite, F; Hill, V; Zhang, C X

    2016-01-01

    We aim at deriving accurate atmospheric parameters and chemical abundances of 19 barium (Ba) stars, including both strong and mild Ba stars, based on the high signal-to-noise ratio and high resolution Echelle spectra obtained from the 2.16 m telescope at Xinglong station of National Astronomical Observatories, Chinese Academy of Sciences. The chemical abundances of the sample stars were obtained from an LTE, plane-parallel and line-blanketed atmospheric model by inputting the atmospheric parameters (effective temperatures, surface gravities, metallicity and microturbulent velocity) and equivalent widths of stellar absorption lines. These samples of Ba stars are giants indicated by atmospheric parameters, metallicities and kinematic analysis about UVW velocity. Chemical abundances of 17 elements were obtained for these Ba stars. Their light elements (O, Na, Mg, Al, Si, Ca, Sc, Ti, V, Cr, Mn and Ni) are similar to the solar abundances. Our samples of Ba stars show obvious overabundances of neutron-capture (n-ca...

  14. Hydrolytic enzyme activity enhanced by Barium supplementation

    Directory of Open Access Journals (Sweden)

    Camilo Muñoz

    2016-10-01

    Full Text Available Hydrolysis of polymers is a first and often limiting step during the degradation of plant residues. Plant biomass is generally a major component of waste residues and a major renewable resource to obtain a variety of secondary products including biofuels. Improving the performance of enzymatic hydrolysis of plant material with minimum costs and limiting the use of additional microbial biomass or hydrolytic enzymes directly influences competitiveness of these green biotechnological processes. In this study, we cloned and expressed a cellulase and two esterases recovered from environmental thermophilic soil bacterial communities and characterize their optimum activity conditions including the effect of several metal ions. Results showed that supplementing these hydrolytic reactions with Barium increases the activity of these extracellular hydrolytic enzymes. This observation represents a simple but major improvement to enhance the efficiency and competitiveness of this process within an increasingly important biotechnological sector.

  15. Liquid phase sintering of BaTiO/sub 3/ by boric oxide (B/sub 2/O/sub 3/) and lead borate (PbB/sub 2/O/sub 4/) glasses and its effect on dielectric strength and dielectric constant

    Energy Technology Data Exchange (ETDEWEB)

    Sarkar, S.K.; Sharma, M.L. (National Physical Lab., New Delhi (India))

    1989-07-01

    A systematic study on liquid phase sintering of barium titanate ceramics with low melting glasses has been done. Liquid phase sintering of barium titanate with low melting glasses has the potential of reducing the sintering temperature of barium titanate and avoiding the use of expensive metals, (Pt, Pd etc) as electrodes in multilayer capacitors. As regards the effect of this technique on dielectric properties, dielectric strengths is found to increase from and dielectric constant is found to decrease.

  16. Dielectric and tunable behavior of lead strontium titanate ceramics and composites

    Science.gov (United States)

    Somiya, Yoshitaka

    The needs of materials for microwave applications have been increasing due to the demands of mobile communication systems and it is preferable for most applications to be manufactured inexpensively using the least amount of space possible. One of the ideas presented to achieve this goal is to reduce the number of components. By changing certain properties under a specific electric and/or magnetic field condition, a component is able to have more than one function, which decreases the number of components necessary. Although microelectromechanical systems (MEMS), semiconductors, and ferrite based devices are available for tuning applications, ferroelectrics in the paraelectric regions and incipient ferroelectric materials are the most promising for low cost and miniaturized products over a wide frequency range of 1-10 GHz and higher frequencies. Barium strontium titanate ((Ba, Sr)TiO3 (BST)) is a considerably studied field dependent ferroelectric material. However, BST requires special techniques to prepare samples which show good reproducibility because the conventional mixed oxide method is not expected to offer high homogeneity due to low reactivity among the raw oxide chemicals of BST. On the contrary, lead strontium titanate ((Sr, Pb)TiO3 (SPT)) permits much simpler processing due to the high reactivity of lead oxide, a raw oxide chemical, towards the other component oxides. Therefore, the SPT system has been selected as a potential candidate for the frequency agile ferroelectrics for electronics (FAME) applications. Selected compositions, for example, Sr-Pb (0.7:0.3 by mole and 0.8:0.2 by mole) in the pure SPT system show the following properties: i) high relative permittivity, epsilonr, ii) low tangent delta in the paraelectric states, iii) moderate DC bias dependence of epsilonr far above the transition temperatures, and iv) high DC bias dependence of epsilon r close to the transition temperatures. In addition, the SPT system does not show a significant

  17. A NOVEL HYDROTHERMAL SYNTHESIS METHOD FOR BARIUM FERRITE

    Institute of Scientific and Technical Information of China (English)

    Kang Li; Hongchen Gu; Qun Wei

    2004-01-01

    In the present work, fine barium ferrite powder has been synthesized through a one-step hydrothermal process in an autoclave at [OH-]/[Cl-] ratio of 2:1 in the temperature range from 180 to 260 ℃ using barium chloride (BaCl2), ferrous chloride (FeCl2) and potassium nitrate (KNO3) as the starting materials. Both particle size and saturation magnetization (Ms) increase with increasing hydrothermal reaction temperature, while the intrinsic coercivity (iHc) peaks at 685 Oe at 230 ℃. Morphology progress from the barium ferrite precursor particles to the barium hexaferrite particles has been monitored with increasing hydrothermal reaction time at 230 ℃ in the autoclave.

  18. Peritonite por bário Barium peritonitis

    Directory of Open Access Journals (Sweden)

    Gerson Alves Pereira Júnior

    1999-10-01

    Full Text Available We report a case of a 49 years-old man who underwent a barium meal examination for an epigastric pain. A perforated gastric ulcer with barium extravasation into peritoneal cavity was seen on X-rays. During an emergency laparotomy, a perforated pyloric ulcer was noted, along with barium contamination in the peritoneal cavity. The ulcer was closed with an omental patch and an extensive peritoneal lavage with saline was performed. During the postoperative period, the patient developed signs of peritonitis and underwent a new laparotomy was at the 9th day showing a subfrenic abscess with a large barium contamination. The patient presented septic shock and multiple organ failure. dying on the 21th day.

  19. Upper gastrointestinal barium evaluation of duodenal pathology: A pictorial review

    Institute of Scientific and Technical Information of China (English)

    Pankaj; Gupta; Uma; Debi; Saroj; Kant; Sinha; Kaushal; Kishor

    2014-01-01

    Like other parts of the gastrointestinal tract(GIT), duodenum is subject to a variety of lesions both congenital and acquired. However, unlike other parts of the GIT viz. esophagus, rest of the small intestine and large intestine, barium evaluation of duodenal lesions is technically more challenging and hence not frequently reported. With significant advances in computed tomography technology, a thorough evaluation including intraluminal, mural and extramural is feasible in a single non-invasive examination. Notwithstanding, barium evaluation still remains the initial and sometimes the only imaging study in several parts of the world. Hence,a thorough acquaintance with the morphology of various duodenal lesions on upper gastrointestinal barium examination is essential in guiding further evaluation. We reviewed our experience with various common and uncommon barium findings in duodenal abnormalities.

  20. Coastal barium cycling at the West Antarctic Peninsula

    Science.gov (United States)

    Pyle, K. M.; Hendry, K. R.; Sherrell, R. M.; Meredith, M. P.; Venables, H.; Lagerström, M.; Morte-Ródenas, A.

    2017-05-01

    Barium cycling in the ocean is associated with a number of processes, including the production and recycling of organic matter, freshwater fluxes, and phenomena that affect alkalinity. As a result, the biogeochemical cycle of barium offers insights into past and present oceanic conditions, with barium currently used in various forms as a palaeoproxy for components of organic and inorganic carbon storage, and as a quasi-conservative water mass tracer. However, the nature of the oceanic barium cycle is not fully understood, particularly in cases where multiple processes may be interacting simultaneously with the dissolved and particulate barium pools. This is particularly the case in coastal polar regions such as the West Antarctic Peninsula, where biological drawdown and remineralisation occur in tandem with sea ice formation and melting, glacial meltwater input, and potential fluxes from shelf sediments. Here, we use a high-precision dataset of dissolved barium (Bad) from a grid of stations adjacent to the West Antarctic Peninsula in conjunction with silicic acid (Si(OH)4), the oxygen isotope composition of water, and salinity measurements, to determine the relative control of various coastal processes on the barium cycle throughout the water column. There is a strong correlation between Bad and Si(OH)4 present in deeper samples, but nevertheless persists significantly in surface waters. This indicates that the link between biogenic opal and barium is not solely due to barite precipitation and dissolution at depth, but is supplemented by an association between Bad and diatom tests in surface waters, possibly due to barite formation within diatom-dominated phytodetritus present in the photic zone. Sea-ice meltwater appears to exert a significant secondary control on barium concentrations, likely due to non-conservative biotic or abiotic processes acting as a sink for Bad within the sea ice itself, or sea-ice meltwater stimulating non-siliceous productivity that acts

  1. Synthesis, photoluminescence and magnetic properties of barium vanadate nanoflowers

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Jing [Department of Applied Physics, Chongqing University, 174 Shapingba Street, Chongqing 400044 (China); Chongqing University of Science and Technology, Chongqing 401331 (China); Hu, Chenguo, E-mail: hucg@cqu.edu.cn [Department of Applied Physics, Chongqing University, 174 Shapingba Street, Chongqing 400044 (China); Xi, Yi [Department of Applied Physics, Chongqing University, 174 Shapingba Street, Chongqing 400044 (China); Peng, Chen [School of Physical Science and Technology, Southwest University, Chongqing 400715 (China); Wan, Buyong; He, Xiaoshan [Department of Applied Physics, Chongqing University, 174 Shapingba Street, Chongqing 400044 (China)

    2011-06-15

    Graphical abstract: The flower-shaped barium vanadate was obtained for the first time. The photoluminescence and magnetic properties of the barium vanadate nanoflowers were investigated at room temperature. Research highlights: {yields} In the paper, the flower-shaped barium vanadate were obtained for the first time. The CHM method used here is new and simple for preparation of barium vanadate. {yields} The photoluminescence and magnetic properties of the barium vanadate nanoflowers were investigated at room temperature. The strong bluish-green emission was observed. {yields} The ferromagnetic behavior of the barium vanadate nanoflowers was found with saturation magnetization of about 83.50 x 10{sup -3} emu/g, coercivity of 18.89 Oe and remnant magnetization of 4.63 x 10{sup -3} emu/g. {yields} The mechanisms of PL and magnetic property of barium vanadate nanoflowers have been discussed. -- Abstract: The flower-shaped barium vanadate has been obtained by the composite hydroxide mediated (CHM) method from V{sub 2}O{sub 5} and BaCl{sub 2} at 200 {sup o}C for 13 h. XRD and XPS spectrum of the as-synthesized sample indicate it is hexagonal Ba{sub 3}V{sub 2}O{sub 8} with small amount of Ba{sub 3}VO{sub 4.8} coexistence. Scan electron microscope and transmission electron microscope display that the flower-shaped crystals are composed of nanosheets with thickness of {approx}20 nm. The UV-visible spectrum shows that the barium vanadate sample has two optical gaps (3.85 eV and 3.12 eV). Photoluminescence spectrum of the barium vanadate flowers exhibits a visible light emission centered at 492 and 525 nm which might be attributed to VO{sub 4} tetrahedron with T{sub d} symmetry in Ba{sub 3}V{sub 2}O{sub 8}. The ferromagnetic behavior of the barium vanadate nanoflowers has been found with saturation magnetization of about 83.50 x 10{sup -3} emu/g, coercivity of 18.89 Oe and remnant magnetization of 4.63 x 10{sup -3} emu/g, which is mainly due to the presence of a non

  2. Solar eclipse sign of intussusception on barium enema.

    Science.gov (United States)

    Raveenthiran, V

    2002-01-01

    The colographic appearance of intussusception is variously described as a claw sign, pincer defect, shouldering effect, and coiled-spring pattern. This report adds a new radiographic sign to the list. An end-on view of an intussusception on barium enema shows a ring of contrast resembling a solar eclipse. Familiarity with this bizarre appearance is desirable, lest it may be mistaken for spillage of barium due to a colonic perforation.

  3. INFLUENCE OF BARIUM OXIDE ADDITIONS ON PORTLAND CLINKER

    OpenAIRE

    Anezka Zezulova; Theodor Stanek; Opravil Tomas

    2016-01-01

    Nowadays, nuclear power plants are widespread around the world and research is of great interest. Together with nuclear research, shielding of different types of radiation is an important current topic of research aiming at their safety. Portland cement has been an elementary building material for centuries. Since barium is very efficient in shielding different types of radiation, it can be assumed that the radiation shielding capability of cement can be improved by incorporation of barium. ...

  4. STRONTIUM AS AN EFFICIENT PROMOTER FOR SUPPORTED PALLADIUM HYDROGENATION CATALYSTS

    Science.gov (United States)

    The effect of strontium promotion is studied for a series of supported palladium catalysts such as Pd/zeolite-β, Pd/Al2O3, Pd/SiO2, Pd/hydrotalcite and Pd/MgO. Strontium is found to be an effective promoter for enhancing the metal area, perce...

  5. Age and gender specific biokinetic model for strontium in humans

    Energy Technology Data Exchange (ETDEWEB)

    Shagina, N. B.; Tolstykh, E. I.; Degteva, M. O.; Anspaugh, L. R.; Napier, Bruce A.

    2015-03-01

    A biokinetic model for strontium in humans is necessary for quantification of internal doses due to strontium radioisotopes. The ICRP-recommended biokinetic model for strontium has limitation for use in a population study, because it is not gender specific and does not cover all age ranges. The extensive Techa River data set on 90Sr in humans (tens of thousands of measurements) is a unique source of data on long-term strontium retention for men and women of all ages at intake. These, as well as published data, were used for evaluation of age- and gender-specific parameters for a new compartment biokinetic model for strontium (Sr-AGe model). The Sr-AGe model has similar structure as the ICRP model for the alkaline earth elements. The following parameters were mainly reevaluated: gastro-intestinal absorption and parameters related to the processes of bone formation and resorption defining calcium and strontium transfers in skeletal compartments. The Sr-AGe model satisfactorily describes available data sets on strontium retention for different kinds of intake (dietary and intravenous) at different ages (0–80 years old) and demonstrates good agreement with data sets for different ethnic groups. The Sr-AGe model can be used for dose assessment in epidemiological studies of general population exposed to ingested strontium radioisotopes.

  6. Process for the extraction of strontium from acidic solutions

    Energy Technology Data Exchange (ETDEWEB)

    Horwitz, E.P.; Dietz, M.L.

    1993-01-01

    The invention is a process for selectively extracting strontium values from aqueous nitric acid waste solutions containing these and other fission product values. The extractant solution is a macrocyclic polyether in an aliphatic hydrocarbon diluent containing a phase modifier. The process will selectively extract strontium values from nitric acid solutions which are up to 6 molar in nitric acid.

  7. Lifetime Measurement for 6snp Rydberg States of Barium

    Institute of Scientific and Technical Information of China (English)

    SHEN Li; WANG Lei; YANG Hai-Feng; LIU Xiao-Jun; LIU Hong-Ping

    2011-01-01

    @@ We present a simple and efficient method for measuring the atomic lifetimes in order of tens of microseconds and demonstrate it in the lifetime determination of barium Rydberg states.This method extracts the lifetime information from the time-of-flight spectrum directly, which is much more efficient than other methods such as the time-delayed field ionization and the traditional laser induced fluorescence.The lifetimes determined with our method for barium Rydberg 6snp(n=37-59)series are well coincident with the values deduced from the absolute oscillator strengths of barium which were given in the literature [J.Phys.B 14(1981)4489, 29(1996)655]on experiments.%We present a simple and efficient method for measuring the atomic lifetimes in order of tens of microseconds and demonstrate it in the lifetime determination of barium Rydberg states. This method extracts the lifetime information from the time-of-flight spectrum directly, which is much more efficient than other methods such as the time-delayed field ionization and the traditional laser induced fluorescence. The lifetimes determined with our method for barium Rydberg 6snp (n=37-59) series are well coincident with the values deduced from the absolute oscillator strengths of barium which were given in the literature [J. Phys. B 14 (1981) 4489, 29 (1996) 655] onexperiments.

  8. Strontium titanate - An index to the literature on properties and the growth of single crystals

    Science.gov (United States)

    Nassau, K.; Miller, A. E.

    1988-08-01

    This paper presents a list of references to the most important information concerning properties and the growth conditions of single-crystal SrTiO3. References to a wide variety of crystal growth techniques are presented, with special consideration given to those for the Verneuil technique. References to the properties of strontium titanate are grouped into five categories: (1) structural, thermal, and mechanical properties; (2) electric and magnetic properties; (3) optical and related properties; (4) phase diagrams, mixed systems, and chemical properties; and (5) the dopants used and their properties. Some of the more useful numerical constants are also included.

  9. Size effects of 109° domain walls in rhombohedral barium titanate single crystals—A molecular statics analysis

    Energy Technology Data Exchange (ETDEWEB)

    Endres, Florian, E-mail: florian.endres@ltm.uni-erlangen.de; Steinmann, Paul, E-mail: paul.steinmann@ltm.uni-erlangen.de [Department of Mechanical Engineering, University of Erlangen - Nuremberg, Paul-Gordan Str. 3, 91052 Erlangen (Germany)

    2016-01-14

    Ferroelectric functional materials are of great interest in science and technology due to their electromechanically coupled material properties. Therefore, ferroelectrics, such as barium titanate, are modeled and simulated at the continuum scale as well as at the atomistic scale. Due to recent advancements in related manufacturing technologies the modeling and simulation of smart materials at the nanometer length scale is getting more important not only to predict but also fundamentally understand the complex material behavior of such materials. In this study, we analyze the size effects of 109° nanodomain walls in ferroelectric barium titanate single crystals in the rhombohedral phase using a recently proposed extended molecular statics algorithm. We study the impact of domain thicknesses on the spontaneous polarization, the coercive field, and the lattice constants. Moreover, we discuss how the electromechanical coupling of an applied electric field and the introduced strain in the converse piezoelectric effect is affected by the thickness of nanodomains.

  10. Complex permittivity, permeability and microwave absorbing properties of Co–Ti substituted strontium hexaferrite

    Directory of Open Access Journals (Sweden)

    Bindra Narang Sukhleen

    2016-03-01

    Full Text Available M-type strontium ferrite with compositions SrFe(12-2xCoxTixO19 (x = 0.0, 0.3, 0.5, 0.7, 1.0, were prepared by two route ceramic method. The effects of Co–Ti substitution on their microstructure, electromagnetic properties, and microwave absorptive behavior were analyzed. The complex permittivity (∊′-j∊″ and complex permeability (μ′-jμ″ have been measured from 8.2 to 12.4 GHz using a network analyzer. Scanning electron microscope was used to analyze the grain size distribution and porosity of the ferrite. X-ray diffraction confirmed the M-type structure of the doped strontium ferrite. Vibrating sample magnetometer was used to study hysteresis loop of the ferrite. This study suggests that the control of grain size, decrease in coercivity and enhanced values of dielectric constant and loss are effective means to improve microwave absorption. The dielectric constant and loss were enhanced in comparison to the permeability constant and loss over the entire frequency range.

  11. Strontium Promotes Cementoblasts Differentiation through Inhibiting Sclerostin Expression In Vitro

    Directory of Open Access Journals (Sweden)

    Xingfu Bao

    2014-01-01

    Full Text Available Cementogenesis, performed by cementoblasts, is important for the repair of root resorption caused by orthodontic treatment. Based on recent studies, strontium has been applied for osteoporosis treatment due to its positive effect on osteoblasts. Although promising, the effect of strontium on cementoblasts is still unclear. So the aim of this research was to clarify and investigate the effect of strontium on cementogenesis via employing cementoblasts as model. A series of experiments including MTT, alkaline phosphatase activity, gene analysis, alizarin red staining, and western blot were carried out to evaluate the proliferation and differentiation of cementoblasts. In addition, expression of sclerostin was checked to analyze the possible mechanism. Our results show that strontium inhibits the proliferation of cementoblasts with a dose dependent manner; however, it can promote the differentiation of cementoblasts via downregulating sclerostin expression. Taking together, strontium may facilitate cementogenesis and benefit the treatment of root resorption at a low dose.

  12. Dielectric property of polyimide/barium titanate composites and its influence factors (Ⅱ)

    Institute of Scientific and Technical Information of China (English)

    Weidong LIU; Baoku ZHU; Shuhui XIE; Zhikang XU

    2008-01-01

    Using poly(amic acid) (PAA) as a precursor followed by thermal imidization, the polyimide/barium titanate composite films were successfully prepared by a direct mixing method and in situ process. The influence of processing factors, such as particle size, distribution mode and polymerization method on dielectric prop-erties was studied. Results revealed that the dielectric constant (ε) of the composite film increased by using bigger fillers or employing in situ polymerization and bimodal distribution. When the composite film contain-ing 50 Vol-% of BaTiO3 with size in 100 nm was pre-pared via in situ process, its dielectric constant reached 45 at 10 kHz.

  13. Exploring the Origin of Lithium, Carbon, Strontium and Barium with four new Ultra Metal-Poor Stars

    CERN Document Server

    Hansen, T; Christlieb, N; Yong, D; Bessell, M S; Pérez, A E García; Beers, T C; Placco, V M; Frebel, A; Norris, J E; Asplund, M

    2014-01-01

    We present an elemental abundance analysis for four newly discovered ultra metal-poor stars from the Hamburg/ESO survey, with $\\mathrm{[Fe/H]}\\leq-4$. Based on high-resolution, high signal-to-noise spectra, we derive abundances for 17 elements in the range from Li to Ba. Three of the four stars exhibit moderate to large over-abundances of carbon, but have no enhancements in their neutron-capture elements. The most metal-poor star in the sample, HE~0233$-$0343 ($\\mathrm{[Fe/H]} = -4.68$), is a subgiant with a carbon enhancement of $\\mathrm{[C/Fe]}= +3.5$, slightly above the carbon-enhancement plateau suggested by Spite et al. No carbon is detected in the spectrum of the fourth star, but the quality of its spectrum only allows for the determination of an upper limit on the carbon abundance ratio of $\\mathrm{[C/Fe]} < +1.7$. We detect lithium in the spectra of two of the carbon-enhanced stars, including HE~0233$-$0343. Both stars with Li detections are Li-depleted, with respect to the Li plateau for metal-poo...

  14. Propagation characteristics of a focused laser beam in a strontium barium niobate photorefractive crystal under reverse external electric field.

    Science.gov (United States)

    Guo, Q L; Liang, B L; Wang, Y; Deng, G Y; Jiang, Y H; Zhang, S H; Fu, G S; Simmonds, P J

    2014-10-01

    The propagation characteristics of a focused laser beam in a SBN:75 photorefractive crystal strongly depend on the signal-to-background intensity ratio (R=Is/Ib) under reverse external electric field. In the range 20>R>0.05, the laser beam shows enhanced self-defocusing behavior with increasing external electric field, while it shows self-focusing in the range 0.03>R>0.01. Spatial solitons are observed under a suitable reverse external electric field for R=0.025. A theoretical model is proposed to explain the experimental observations, which suggest a new type of soliton formation due to "enhancement" not "screening" of the external electrical field.

  15. Crystalline silicotitanates for cesium/strontium removal

    Energy Technology Data Exchange (ETDEWEB)

    Brown, N.; Miller, J.; Sherman, J.

    1996-10-01

    A new class of inorganic ion exchangers called crystalline silicotitanates (CST) has been developed that exhibits very high selectivity for cesium and strontium in the highly alkaline radioactive wastes at the Hanford Site and other DOE sites. Tests have also shown that CSTs have high selectivity for cesium in acidic and neutral solutions. The ESP is supporting an effort at Sandia National Laboratories and Texas A & M University to further develop and characterize the important chemical and physical properties that will determine the applicability of CST to radioactive waste treatment at Hanford and other DOE facilities.

  16. Nondestructive measurement of environmental radioactive strontium

    Science.gov (United States)

    Saiba, Shuntaro; Okamiya, Tomohiro; Tanaka, Saki; Tanuma, Ryosuke; Totsuka, Yumi; Murata, Jiro

    2014-03-01

    The Fukushima Daiichi nuclear power plant accident was triggered by the 2011 Great East Japan Earthquake. The main radioactivity concerns after the accident are I-131 (half-life: 8.0 days), Cs-134 (2.1 years), Cs-137 (30 years), Sr-89 (51 days), and Sr-90 (29 years). We are aiming to establish a new nondestructive measurement and detection technique that will enable us to realize a quantitative evaluation of strontium radioactivity without chemical separation processing. This technique is needed to detect radiation contained in foods, environmental water, and soil, to prevent us from undesired internal exposure to radiation.

  17. Nondestructive measurement of environmental radioactive strontium

    Directory of Open Access Journals (Sweden)

    Saiba Shuntaro

    2014-03-01

    Full Text Available The Fukushima Daiichi nuclear power plant accident was triggered by the 2011 Great East Japan Earthquake. The main radioactivity concerns after the accident are I-131 (half-life: 8.0 days, Cs-134 (2.1 years, Cs-137 (30 years, Sr-89 (51 days, and Sr-90 (29 years. We are aiming to establish a new nondestructive measurement and detection technique that will enable us to realize a quantitative evaluation of strontium radioactivity without chemical separation processing. This technique is needed to detect radiation contained in foods, environmental water, and soil, to prevent us from undesired internal exposure to radiation.

  18. Eu2+ luminescence in strontium aluminates

    OpenAIRE

    Dutczak, D.; Juestel, T.; Ronda, C.; Meijerink, A.|info:eu-repo/dai/nl/075044986

    2015-01-01

    The luminescence properties of Eu2+ doped strontium aluminates are reported and reviewed for a variety of aluminates, viz. SrAl12O19, SrAl4O7, Sr4Al14O25, SrAl2O4 and Sr3Al2O6. The aim of the research is to investigate the role of local coordination and covalency of the aluminate host lattice, related to the Sr/Al ratio, on the optical properties of the Eu2+ ion. The UV and VUV excited luminescence spectra as well as luminescence decay curves were recorded to characterize the luminescence pro...

  19. Efficient cooling and trapping of strontium atoms.

    Science.gov (United States)

    Courtillot, I; Quessada, A; Kovacich, R P; Zondy, J J; Landragin, A; Clairon, A; Lemonde, P

    2003-03-15

    We report the capture of cold strontium atoms in a magneto-optical trap (MOT) at a rate of 4 x 10(10) atoms/s. The MOT is loaded from an atomic beam decelerated by a Zeeman slower operating with a focused laser beam. The 461-nm laser, used for both cooling and trapping, was generated by sum-frequency mixing in a KTP crystal with diode lasers at 813 nm and a Nd:YAG laser at 1064 nm. As much as 115 mW of blue light was obtained.

  20. Increased strontium uptake in trabecular bone of ovariectomized calcium-deficient rats treated with strontium ranelate or strontium chloride.

    Science.gov (United States)

    Pemmer, Bernhard; Hofstaetter, Jochen G; Meirer, Florian; Smolek, Stephan; Wobrauschek, Peter; Simon, Rolf; Fuchs, Robyn K; Allen, Matthew R; Condon, Keith W; Reinwald, Susan; Phipps, Roger J; Burr, David B; Paschalis, Eleftherios P; Klaushofer, Klaus; Streli, Christina; Roschger, Paul

    2011-11-01

    Based on clinical trials showing the efficacy to reduce vertebral and non-vertebral fractures, strontium ranelate (SrR) has been approved in several countries for the treatment of postmenopausal osteoporosis. Hence, it is of special clinical interest to elucidate how the Sr uptake is influenced by dietary Ca deficiency as well as by the formula of Sr administration, SrR versus strontium chloride (SrCl(2)). Three-month-old ovariectomized rats were treated for 90 days with doses of 25 mg kg(-1) d(-1) and 150 mg kg(-1) d(-1) of SrR or SrCl(2) at low (0.1% Ca) or normal (1.19% Ca) Ca diet. Vertebral bone tissue was analysed by confocal synchrotron-radiation-induced micro X-ray fluorescence and by backscattered electron imaging. Principal component analysis and k-means clustering of the acquired elemental maps of Ca and Sr revealed that the newly formed bone exhibited the highest Sr fractions and that low Ca diet increased the Sr uptake by a factor of three to four. Furthermore, Sr uptake in bone of the SrCl(2)-treated animals was generally lower compared with SrR. The study clearly shows that inadequate nutritional calcium intake significantly increases uptake of Sr in serum as well as in trabecular bone matrix. This indicates that nutritional calcium intake as well as serum Ca levels are important regulators of any Sr treatment.

  1. The efficacy of steroids for postoperative persistent inflammatory reaction in a patient with barium peritonitis: A case report

    Directory of Open Access Journals (Sweden)

    Hirofumi Kojima

    2017-01-01

    Conclusion: Residual barium in the intraperitoneal cavity causes persistent inflammatory reaction in patients with barium peritonitis. The use of steroids is effective for postoperative persistent inflammation due to the residual barium.

  2. Investigation of strontium accumulation on ovariectomized Sprague–Dawley rat tibia by micro-PIXE

    Energy Technology Data Exchange (ETDEWEB)

    Li, X.; Li, Y. [Institute of Modern Physics, Fudan University, Shanghai 200433 (China); Jin, W. [Institute of Radiation Medicine, Fudan University, Shanghai 200032 (China); Zheng, Y.; Rong, C.; Lyu, H. [Institute of Modern Physics, Fudan University, Shanghai 200433 (China); Shen, H., E-mail: haoshen@fudan.edu.cn [Institute of Modern Physics, Fudan University, Shanghai 200433 (China)

    2014-08-01

    Strontium ranelate is a newly developed drug effective in osteoporosis treatment by depressing bone resorption and maintaining bone formation. Strontium accumulation and distribution are determined in bones of rat after strontium ranelate administration by using micro-PIXE. The investigated rats are divided into four groups: (A) control, (B) ovariectomized, (C) ovariectomized followed with strontium chloride, (D) ovariectomized followed with strontium ranelate. It was found that strontium ranelate would result in increasing trabecular volume and decreasing bone resorption to treat osteoporosis. There are similar contours of calcium and strontium in two-dimensional images, while the strontium is not evenly distributed in the bone. It supports the conclusion that strontium has an affinity for bone and it is capable of replacing calcium atoms as a part of the strontium mechanism in the osteoporosis treatment. The results related to biochemistry are also discussed.

  3. Investigation of strontium accumulation on ovariectomized Sprague-Dawley rat tibia by micro-PIXE

    Science.gov (United States)

    Li, X.; Li, Y.; Jin, W.; Zheng, Y.; Rong, C.; Lyu, H.; Shen, H.

    2014-08-01

    Strontium ranelate is a newly developed drug effective in osteoporosis treatment by depressing bone resorption and maintaining bone formation. Strontium accumulation and distribution are determined in bones of rat after strontium ranelate administration by using micro-PIXE. The investigated rats are divided into four groups: (A) control, (B) ovariectomized, (C) ovariectomized followed with strontium chloride, (D) ovariectomized followed with strontium ranelate. It was found that strontium ranelate would result in increasing trabecular volume and decreasing bone resorption to treat osteoporosis. There are similar contours of calcium and strontium in two-dimensional images, while the strontium is not evenly distributed in the bone. It supports the conclusion that strontium has an affinity for bone and it is capable of replacing calcium atoms as a part of the strontium mechanism in the osteoporosis treatment. The results related to biochemistry are also discussed.

  4. Curie temperature and magnetic properties of aluminum doped barium ferrite particles prepared by ball mill method

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Daming [Center for Magnetism and Magnetic Nanostructures, University of Colorado at Colorado Springs, 1420 Austin Bluffs Pkwy, Colorado Springs, Colorado 80918 (United States); College of Materials and Chemical Engineering, Hainan University, Haikou 570228, Hainan (China); Harward, Ian; Baptist, Joshua; Goldman, Sara; Celinski, Zbigniew [Center for Magnetism and Magnetic Nanostructures, University of Colorado at Colorado Springs, 1420 Austin Bluffs Pkwy, Colorado Springs, Colorado 80918 (United States)

    2015-12-01

    Barium ferrite has attracted considerable interest in the fields of permanent magnets and perpendicular magnetic recording due to its strong uniaxial anisotropy and high Curie temperature (T{sub c}). We prepared aluminum doped barium ferrite ceramics (BaAl{sub x}Fe{sub 12−x}O{sub 19}, 0≤x≤6) by the ball mill method. The powder was milled for 96 h, and after forming pellets, annealed for 48 h in air at 1000 °C. The X-ray diffraction (XRD) data show that there are only single hexagonal phases in the samples without any impurity phase. The crystal lattice constants, a and c, were calculated by Cohen's method. Both a and c decrease with increasing x, ranging from 0.588 nm and 2.318 nm to 0.573 nm and 2.294 nm, respectively. A Vibrating Sample Magnetometer (VSM) and Superconducting Quantum Interference Device (SQUID) were used to investigate T{sub c} and magnetic properties of BaFe{sub 12−x}Al{sub x}O{sub 19}. It is found that T{sub c} decreases with increasing x, from 425 °C to 298 °C. It is also found that the saturated magnetization (4πM{sub s}) decreases with increasing x, while the coercivity (H{sub c}) increases with the increase in x. The anisotropy field was also determined from the SQUID measurement. - Highlights: • The Curie temperature and magnetic properties of aluminum doped barium ferrite particles were studied systemically. • The relation between 4πM{sub s} and composition x at 50 K (both experimental value and theoretical calculation) was revealed. • Occupation number for spin up and spin down as a function of temperature was shown. • The relation between 4πM{sub s} and composition x from 50 K to room temperature was revealed.

  5. Chemical compositions of four barium stars

    CERN Document Server

    Liang, Y C; Chen, Y Q; Qiu, H M; Zhang, B

    2003-01-01

    Chemical compositions of four barium stars HD 26886, HD 27271, HD 50082 and HD 98839 are studied based on high resolution, high signal-to-noise Echelle spectra. Results show that all of them are disk stars. Their \\alpha and iron peak elements are similar to the solar abundances. The neutron-capture process elements are overabundant relative to the Solar. The heavy-element abundances of the strong Ba star HD 50082 are higher than those of other three mild Ba stars. Its mass is 1.32Msun (+0.28,-0.22Msun), and is consistent with the average mass of strong Ba stars (1.5Msun). For mild Ba star HD 27271 and HD 26886, the derived masses are 1.90Msun (+0.25,-0.20Msun) and 2.78Msun (+0.75,-0.78M_sun), respectively, which are consistent with the average mass of mild Ba stars. We also calculate the theoretical abundances of Ba stars by combining the AGB stars nucleosynthesis and wind accretion formation scenario of Ba binary systems. The comparisons between the observed abundance patterns of the sample stars with the th...

  6. High H- ionic conductivity in barium hydride

    Science.gov (United States)

    Verbraeken, Maarten C.; Cheung, Chaksum; Suard, Emmanuelle; Irvine, John T. S.

    2015-01-01

    With hydrogen being seen as a key renewable energy vector, the search for materials exhibiting fast hydrogen transport becomes ever more important. Not only do hydrogen storage materials require high mobility of hydrogen in the solid state, but the efficiency of electrochemical devices is also largely determined by fast ionic transport. Although the heavy alkaline-earth hydrides are of limited interest for their hydrogen storage potential, owing to low gravimetric densities, their ionic nature may prove useful in new electrochemical applications, especially as an ionically conducting electrolyte material. Here we show that barium hydride shows fast pure ionic transport of hydride ions (H-) in the high-temperature, high-symmetry phase. Although some conductivity studies have been reported on related materials previously, the nature of the charge carriers has not been determined. BaH2 gives rise to hydride ion conductivity of 0.2 S cm-1 at 630 °C. This is an order of magnitude larger than that of state-of-the-art proton-conducting perovskites or oxide ion conductors at this temperature. These results suggest that the alkaline-earth hydrides form an important new family of materials, with potential use in a number of applications, such as separation membranes, electrochemical reactors and so on.

  7. Elastic Scattering Properties of Ultracold Strontium Atoms

    Institute of Scientific and Technical Information of China (English)

    张计才; 朱遵略; 刘玉芳; 孙金锋

    2011-01-01

    We investigate the elastic scattering properties of strontium atoms at ultracold temperatures.The scattering parameters,such as s-wave scattering lengths,effective ranges and p-wave scattering lengths,are calculated for all stable isotope combinations of Sr atoms by the quantal method and semiclassical method,respectively.Good agreements are obtained.The scattering parameters are very sensitive to small changes of the reduced mass.Due to the repulsive interisotope and intraisotope s-wave scattering length and large elastic cross sections,84Sr-86Srmixture is a good candidate to realize Bose-Bose quantum degenerate atomic gases.%We investigate the elastic scattering properties of strontium atoms at ultracold temperatures. The scattering parameters, such as s-wave scattering lengths, effective ranges and p-wave scattering lengths, are calculated for all stable isotope combinations of Sr atoms by the quantal method and semiclassical method, respectively. Good agreements are obtained. The scattering parameters are very sensitive to small changes of the reduced mass. Due to the repulsive interisotope and intraisotope s-wave scattering length and large elastic cross sections, MSr-s(iSr mixture is a good candidate to realize Bose-Bose quantum degenerate atomic gases.

  8. Laser Stabilization with Laser Cooled Strontium

    DEFF Research Database (Denmark)

    Christensen, Bjarke Takashi Røjle

    The frequency stability of current state-of-the-art stabilized clock lasers are limited by thermal fluctuations of the ultra-stable optical reference cavities used for their frequency stabilization. In this work, we study the possibilities for surpassing this thermal limit by exploiting the nonli......The frequency stability of current state-of-the-art stabilized clock lasers are limited by thermal fluctuations of the ultra-stable optical reference cavities used for their frequency stabilization. In this work, we study the possibilities for surpassing this thermal limit by exploiting...... the nonlinear effects from coupling of an optical cavity to laser cooled atoms having a narrow transition linewidth. Here, we have realized such a system where a thermal sample of laser cooled strontium-88 atoms are coupled to an optical cavity. The strontium-88 atoms were probed on the narrow 1S0-3P1 inter......-combination line at 689 nm in a strongly saturated regime. The dynamics of the atomic induced phase shift and absorption of the probe light were experimentally studied in details with the purpose of applications to laser stabilization. The atomic sample temperature was in the mK range which brought this system out...

  9. The fluoroscopic barium enema in colonic polyp detection.

    Science.gov (United States)

    Teefey, S A; Carlson, H C

    1983-12-01

    The results of 1,500 barium enema studies done by vigorous manual palpation under fluoroscopy were reviewed to determine the adequacy of this technique in detecting polyps above the proctoscopic level. Of the 1,500 patients examined, 103 (7%) were diagnosed radiographically as having a total of 149 polyps. Polyps were found at proctoscopy in about 10% of the 1,500 patients. Colonoscopy or surgery was performed on 35 of the 103 patients. Of the 52 polyps discovered during these procedures, only three were missed at fluoroscopic barium enema study, a false-negative rate of 6%. Fourteen patients whose barium enemas initially were reported as negative for polyps or neoplasia had colonoscopy. Two of the 14 patients had positive findings, for a true-negative rate of 86%. If the detection rate of 7% found at barium enema, taking into account an overlap of 10%, is combined with the rate of 7.5% found at proctoscopy, a frequency of about 14% emerges in detecting polyps in the rectum and in the colon. Thus, the fluoroscopic barium enema when combined with proctoscopy is a sensitive method in the detection of colorectal polyps. In addition, it has the advantage of rapid execution and relatively low cost.

  10. TEM observation of sintered permanent magnetic strontium ferrite

    Institute of Scientific and Technical Information of China (English)

    YU Hongya; LIU Zhengyi; ZENG Dechang

    2006-01-01

    Sintered permanent magnetic strontium ferrites were studied using transmission electron microscopy to investigate the microstructure morphology and its correlation with the magnetic properties. The present study shows that the microstructure of sintered permanent magnetic strontium ferrites is an important parameter in determining their magnetic properties. The microstructure morphology in low-performance ferrite magnet is obviously different from high-performance one. Themagnetic properties of sintered permanent strontium ferrite depend strongly on the orientation degree of strong magnetic crystals. The presence of ferric oxidephase in ferrite magnet can deteriorate the magnetic properties. Moreover, proper quantities of crystal defects are beneficial to high coercive force due to the fixing of magnetic domain.

  11. Seaweed against strontium and preussian blue against cesium

    Directory of Open Access Journals (Sweden)

    G Michanek

    1988-06-01

    Full Text Available The fact that alginates bind strontium and cyanates bind cesium and are capable of removing these elements from living organisms is scientifically verified. Zeolites offer another possibility for exchange of these ions. Practical research should be initiated to find the right doses and procedure to decrease the body burden of radioactive isotopes in reindeer.Alger mot strontium och berlinerblått mot cesium.Abstract in Swedish / Sammanfattning: Mitt budskap år kort: Alger binder strontium, Berlinerblått binder cesium, Sätt fart på forskning och forsök!

  12. X-Ray Absorption Spectroscopy of Strontium(II) Coordination.

    Science.gov (United States)

    O'Day; Newville; Neuhoff; Sahai; Carroll

    2000-02-15

    Detailed analyses of crystalline, hydrated, and precipitated strontium compounds and an aqueous strontium solution by synchrotron extended X-ray absorption fine structure (EXAFS) were used to quantify local thermal and static disorder and to characterize strontium coordination in a variety of oxygen-ligated bonding environments. Analysis of anharmonic vibrational disorder (i.e., significant contribution from a third cumulant term (C(3)) in the EXAFS phase-shift function) in compounds with low and high static disorder around strontium showed that first-shell anharmonic contributions were generally not significant above experimental error in the EXAFS fits (R+/-0.02 Å with and without C(3)). The only case in which a significant apparent decrease in Sr-O distance was observed with increasing temperature, and for which a third cumulant term was significant, was for dilute strontium in aqueous solution. Empirical parameterization of Debye-Waller factor (sigma(2)) for strontium compounds as a function of backscatterer atomic number (Z), interatomic Sr-Z distance, and temperature of spectral data collection showed systematic increases in sigma(2) as a function of increasing temperature and Sr-Z bond length. At values of sigma(2) greater than approximately 0.025 Å(2) (for N3 Å), backscattering was generally not significant above noise levels in spectra of compounds of known crystal structure. Comparison of the EXAFS spectra of freshly precipitated SrCO(3) (spectra collected wet) to that of dry, powdered strontianite (SrCO(3)(s)) indicated no significant differences in the local atomic structure around strontium. Analysis of partially hydrated strontium in natural Ca-zeolite (heulandite) showed that strontium is substituted only in the calcium (Ca2) site. Backscattering from aluminum and silicon atoms in the zeolite framework were apparent in the EXAFS spectra at low and room temperature at distances from central strontium of strontium structural coordination determined

  13. Enhanced Sensitivity of Surface Plasmon Resonance Sensor Based on Bilayers of Silver-Barium Titanate

    Directory of Open Access Journals (Sweden)

    S. Fouad

    2016-12-01

    Full Text Available Surface plasmon resonance (SPR sensors have been widely adopted with various fields such as physics, chemistry, biology and biochemistry. SPR sensor has many advantages like the less number of sensing samples required, freedom of electromagnetic interference and higher sensitivity. This research investigates the phase interrogation technique of a surface plasmon resonance sensor based on silver and thin film dielectric material of Barium titanate layers. Barium titanate (BaTiO3 layer is adopted due to its excellent dielectric properties such as high dielectric constant and low dielectric loss. The numerical results demonstrate that the fusion of the proposed material BaTiO3 layer into surface plasmon resonance sensor yields a higher sensitivity of 280 degree/RIU in comparison with surface plasmon resonance sensor without BaTiO3 layer which shows only a sensitivity of 120 degree/RIU. As the thickness of this layer increases from 5 nm to 10 nm, the sensitivity is enhanced from 160 degree/RIU to 280 degree/RIU for a fixed metal layer of silver with a thickness of (70 nm.

  14. Curie temperature and magnetic properties of aluminum doped barium ferrite particles prepared by ball mill method

    Science.gov (United States)

    Chen, Daming; Harward, Ian; Baptist, Joshua; Goldman, Sara; Celinski, Zbigniew

    2015-12-01

    Barium ferrite has attracted considerable interest in the fields of permanent magnets and perpendicular magnetic recording due to its strong uniaxial anisotropy and high Curie temperature (Tc). We prepared aluminum doped barium ferrite ceramics (BaAlxFe12-xO19, 0≤x≤6) by the ball mill method. The powder was milled for 96 h, and after forming pellets, annealed for 48 h in air at 1000 °C. The X-ray diffraction (XRD) data show that there are only single hexagonal phases in the samples without any impurity phase. The crystal lattice constants, a and c, were calculated by Cohen's method. Both a and c decrease with increasing x, ranging from 0.588 nm and 2.318 nm to 0.573 nm and 2.294 nm, respectively. A Vibrating Sample Magnetometer (VSM) and Superconducting Quantum Interference Device (SQUID) were used to investigate Tc and magnetic properties of BaFe12-xAlxO19. It is found that Tc decreases with increasing x, from 425 °C to 298 °C. It is also found that the saturated magnetization (4πMs) decreases with increasing x, while the coercivity (Hc) increases with the increase in x. The anisotropy field was also determined from the SQUID measurement.

  15. Effect of long-term treatment with strontium ranelate on bone strontium content

    DEFF Research Database (Denmark)

    Bärenholdt, Olaf; Kolthoff, Niels; Nielsen, Stig Pors

    2009-01-01

    in a 3 years open study of the effect on bone Sr. The group was treated with 2 g SrR/day, 17 of the group had received active treatment for 4-5 years before the study. DXA BMD measurements and DPA measurements of the relative bone strontium hydroxy apatite termed %Sr (SrHA/(CaHA+SrHA)) were done...... at the end of treatment. No effect was demonstrated on distal radius relative bone Ca hydroxy apatite. Bone strontium uptake and retention data were compatible with a power function model. Withdrawal of SrR resulted in a decline in bone Sr, but 73 %Sr and 67 %Sr, respectively remained in UD-radius three...

  16. Improvement of Mechanical, Thermal and Optical Properties of Barium Mixed Cobalt Tartrate Hydrate Crystals Grown by Gel Method

    Directory of Open Access Journals (Sweden)

    S. Vanaja

    2015-10-01

    Full Text Available In this present work, CTH and BCTH crystals have been prepared by gel technique by using single diffusion method at room temperature. The as grown crystals were characterized by using XRD, FT-IR, UV, TG / DTA and Micro hardness studies. X-ray powder diffraction results analyzed by using suitable software suggest that a CTH and BCTH crystals belong to cubic crystal system. The unit cell volume is observed to increase with increase in the concentration of barium in cobalt tartrate due to the lattice distortion. The band gap and optical properties have analyzed by UV-Visible spectrum. The functional groups and compound formation of the crystals have been studied by FT-IR spectrum. The mechanical properties of the grown crystals were tested by using Vicker’s microhardness studies. The work hardening coefficient (n was determined to be 3.7 for CTH, 5.3 for BCTH (1 : 1 and 6.4 for BCTH (2 : 1 and the stiffness constants for different loads were calculated and reported. Thermal analysis suggests that pure cobalt tartrate starts decomposing at 73.2 °C whereas the barium mixed cobalt tartrate brings about better thermal stability which increases with an increase in barium concentration.

  17. Durability of Alite-calcium Barium Sulphoaluminate Cement

    Institute of Scientific and Technical Information of China (English)

    LU Lingchao; LU Zeye; LIU Shiquan; WANG Shoude; CHENG Xin

    2009-01-01

    The durability of the cement was mainly studied.Under 1.0 MPa of hydraulic pressure for 8 hours,water could penetrate completely through the sample made by portland cement,but could not penetrate through that by alite-barium sulphoaluminate cement.Under the condition of freezing and thawing cycle,the loss ratio of compressive strength of the cement was only about 17.3%at curing 28 d ages,but the loss of portland cement was as high as 29.5%.Alite-calcium bar-ium sulphoaluminate cement also has an excellent resistance to sulfate attack.The coefficients of resistance to sulfate attack of the cement exceeded 1.0.Meanwhile,the composition and microstructure of the hardened paste of alite-calcium barium sulphoaluminate cement were analyzed by XRD and SEM.

  18. Barium-borate-flyash glasses: As radiation shielding materials

    Science.gov (United States)

    Singh, Sukhpal; Kumar, Ashok; Singh, Devinder; Thind, Kulwant Singh; Mudahar, Gurmel S.

    2008-01-01

    The attenuation coefficients of barium-borate-flyash glasses have been measured for γ-ray photon energies of 356, 662, 1173 and 1332 keV using narrow beam transmission geometry. The photon beam was highly collimated and overall scatter acceptance angle was less than 3°. Our results have an uncertainty of less than 3%. These coefficients were then used to obtain the values of mean free path (mfp), effective atomic number and electron density. Good agreements have been observed between experimental and theoretical values of these parameters. From the studies of the obtained results it is reported here that from the shielding point of view the barium-borate-flyash glasses are better shields to γ-radiations in comparison to the standard radiation shielding concretes and also to the ordinary barium-borate glasses.

  19. Deoxidation Behavior of Alloys Bearing Barium in Molten Steel

    Institute of Scientific and Technical Information of China (English)

    LI Yang; JIANG Zhou-hua; JIANG Mao-fa; WANG Jun-wen; GU Wen-bing

    2003-01-01

    The deoxidation behaviors of alloys bearing barium in pipe steel were researched with MgO crucible under argon atmosphere in MoSi2 furnace at 1 873 K. The total oxygen contents of molten steel, the distribution, size and morphology of deoxidation products in the steel were surveyed. The metamorphic mechanism for deoxidation products of alloy bearing barium was also discussed. The results show that applying alloy bearing barium to the pipe steel, very low total oxygen contents can be obtained, and deoxidation products, which easily float up from molten steel, can be changed into globular shape and uniformly distributed in steel. The equilibrium time of total oxygen is about 25 min, and the terminal total oxygen contents range from 0.002 0 % to 0.002 2 % after treating with SiCa wire. The best deoxidizers are SiAlBaCa and SiAlBaCaSr.

  20. 75 FR 36629 - Barium Chloride From the People's Republic of China: Continuation of Antidumping Duty Order

    Science.gov (United States)

    2010-06-28

    ... International Trade Administration Barium Chloride From the People's Republic of China: Continuation of... China: Final Results of Expedited Third Sunset Review of Antidumping Duty Order, 74 FR 55814 (October 29... Barium Chloride From China, 75 FR 33824 (June 15, 2010), and Barium Chloride from China (Inv. No....

  1. 40 CFR 721.10010 - Barium manganese oxide (BaMnO3).

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Barium manganese oxide (BaMnO3). 721... Substances § 721.10010 Barium manganese oxide (BaMnO3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as barium manganese oxide (BaMnO3) (PMN...

  2. Modified strontium titanates: From defect chemistry to SOFC anodes

    DEFF Research Database (Denmark)

    Verbraeken, M.C.; Ramos, Tania; Agersted, Karsten

    2015-01-01

    Modified strontium titanates have received much attention recently for their potential as anode material in solid oxide fuel cells (SOFC). Their inherent redox stability and superior tolerance to sulphur poisoning and coking as compared to Ni based cermet anodes could improve durability of SOFC...... systems dramatically. Various substitution strategies can be deployed to optimise materials properties in these strontium titanates, such as electronic conductivity, electrocatalytic activity, chemical stability and sinterability, and thus mechanical strength. Substitution strategies not only cover choice...... of modified strontium titanates, this paper reviews three different A-site deficient donor (La, Y, Nb) substituted strontium titanates for their electrical behaviour and fuel cell performance. Promising performances in both electrolyte as well as anode supported cell designs have been obtained, when using...

  3. The strontium isotope distribution in water and fish within major ...

    African Journals Online (AJOL)

    2016-04-02

    Apr 2, 2016 ... INTRODUCTION. Strontium has 4 ... Penne and Pierce. (2006), in a ... larly add information about possible anthropogenic influences. e aim of this paper is ...... isotopes as tracers of ecosystem processes: theory and meth- ods.

  4. Strontium removal jar test dataset for all figures and tables.

    Data.gov (United States)

    U.S. Environmental Protection Agency — The datasets where used to generate data to demonstrate strontium removal under various water quality and treatment conditions. This dataset is associated with the...

  5. Production of high-n strontium Rydberg atoms

    Science.gov (United States)

    Ye, S.; Zhang, X.; Killian, T. C.; Dunning, F. B.; Hiller, M.; Yoshida, S.; Burgdörfer, J.

    2014-04-01

    The photoexcitation of strontium Rydberg atoms with n ~ 300 is being examined using a crossed laser-atom beam approach to enable study of quasi-stable two-electron excited states and of strongly-coupled Rydberg systems.

  6. Photoionization and Photoelectric Loading of Barium Ion Traps

    CERN Document Server

    Steele, A V; Churchill, L R; Griffin, P F

    2007-01-01

    Simple and effective techniques for loading barium ions into linear Paul traps are demonstrated. Two-step photoionization of neutral barium is achieved using a weak intercombination line (6s2 1S0 6s6p 3P1, 791 nm) followed by excitation above the ionization threshold using a nitrogen gas laser (337 nm). Isotopic selectivity is achieved by using a near Doppler-free geometry for excitation of the triplet 6s6p 3P1 state. Additionally, we report a particularly simple and efficient trap loading technique that employs an in-expensive UV epoxy curing lamp to generate photoelectrons.

  7. Esophageal intramural pseudodiverticulosis characterized by barium esophagography: a case report

    LENUS (Irish Health Repository)

    O'Connor, Owen J

    2010-05-21

    Abstract Introduction Esophageal intramural pseudodiverticulosis is a rare condition characterized by the dilatation of the submucosal glands. Case presentation We present a case of esophageal intramural pseudodiverticulosis in a 72-year-old Caucasian man who presented with dysphagia and with a background history of alcohol abuse. An upper gastrointestinal endoscopy of our patient showed an esophageal stricture with abnormal mucosal appearances, but no malignant cells were seen at biopsy. Appearances on a barium esophagram were pathognomonic for esophageal intramural pseudodiverticulosis. Conclusion We demonstrate the enduring usefulness of barium esophagography in the characterization of abnormal mucosal appearances at endoscopy.

  8. Progress Toward Intercombination Line Cooling in Strontium

    Science.gov (United States)

    Nagel, Sarah B.; Simien, Clayton; Vudayagiri, Ashok; Killian, Thomas C.

    2002-05-01

    An external-cavity, grating-tuned diode laser system is being developed for laser cooling on the 689 nm intercombination line of Strontium (^1S0 arrow ^2P_1, Γ= (2π)*7.5 kHz), using commercially availably laser diodes. We are making progress toward locking the external-cavity diode laser to a heat pipe to produce a few mW of tunable, stabilized, single-mode power at 689 nm. The output from this laser can be injected into a slave laser to produce up to 35 mW of stabilized polarized single-mode power. The completed laser system will be used for both high-resolution spectroscopy and laser cooling. The design of this laser system as well as preliminary results will be presented.

  9. Quantum Simulation and Quantum Sensing with Ultracold Strontium

    Science.gov (United States)

    2015-09-18

    tium. A diagram and photo of the experimental setup appears in Fig. 2. The strontium trap is loaded from an effusive oven which contains a multi...Arlington VA 22203 Approved for public release. We have built an ultra-high vacuum experimental apparatus for trapping and cooling of strontium, demonstrated...its operation, and used it to trap and cool all four stable isotopes of this alkaline earth metal. As part of the design and construction of this

  10. Porous allograft bone scaffolds: doping with strontium.

    Directory of Open Access Journals (Sweden)

    Yantao Zhao

    Full Text Available Strontium (Sr can promote the process of bone formation. To improve bioactivity, porous allograft bone scaffolds (ABS were doped with Sr and the mechanical strength and bioactivity of the scaffolds were evaluated. Sr-doped ABS were prepared using the ion exchange method. The density and distribution of Sr in bone scaffolds were investigated by inductively coupled plasma optical emission spectrometry (ICP-OES, X-ray photoelectron spectroscopy (XPS, and energy-dispersive X-ray spectroscopy (EDS. Controlled release of strontium ions was measured and mechanical strength was evaluated by a compressive strength test. The bioactivity of Sr-doped ABS was investigated by a simulated body fluid (SBF assay, cytotoxicity testing, and an in vivo implantation experiment. The Sr molar concentration [Sr/(Sr+Ca] in ABS surpassed 5% and Sr was distributed nearly evenly. XPS analyses suggest that Sr combined with oxygen and carbonate radicals. Released Sr ions were detected in the immersion solution at higher concentration than calcium ions until day 30. The compressive strength of the Sr-doped ABS did not change significantly. The bioactivity of Sr-doped material, as measured by the in vitro SBF immersion method, was superior to that of the Sr-free freeze-dried bone and the Sr-doped material did not show cytotoxicity compared with Sr-free culture medium. The rate of bone mineral deposition for Sr-doped ABS was faster than that of the control at 4 weeks (3.28 ± 0.23 µm/day vs. 2.60 ± 0.20 µm/day; p<0.05. Sr can be evenly doped into porous ABS at relevant concentrations to create highly active bone substitutes.

  11. High temperature annealing studies of strontium ion implanted glassy carbon

    Energy Technology Data Exchange (ETDEWEB)

    Odutemowo, O.S., E-mail: u12052613@tuks.co.za [Department of Physics, University of Pretoria, Pretoria 0002 (South Africa); Malherbe, J.B.; Prinsloo, L.; Langa, D.F. [Department of Physics, University of Pretoria, Pretoria 0002 (South Africa); Wendler, E. [Institut für Festkörperphysik, Friedrich-Schiller University, Jena (Germany)

    2016-03-15

    Glassy carbon samples were implanted with 200 keV strontium ions to a fluence of 2 × 10{sup 16} ions/cm{sup 2} at room temperature. Analysis with Raman spectroscopy showed that ion bombardment amorphises the glassy carbon structure. Partial recovery of the glassy carbon structure was achieved after the implanted sample was vacuum annealed at 900 °C for 1 h. Annealing the strontium ion bombarded sample at 2000 °C for 5 h resulted in recovery of the glassy carbon substrate with the intensity of the D peak becoming lower than that of the pristine glassy carbon. Rutherford backscattering spectroscopy (RBS) showed that the implanted strontium diffused towards the surface of the glassy carbon after annealing the sample at 900 °C. This diffusion was also accompanied by loss of the implanted strontium. Comparison between the as-implanted and 900 °C depth profiles showed that less than 30% of the strontium was retained in the glassy carbon after heat treatment at 900 °C. The RBS profile after annealing at 2000 °C indicated that no strontium ions were retained after heat treatment at this temperature.

  12. High temperature annealing studies of strontium ion implanted glassy carbon

    Science.gov (United States)

    Odutemowo, O. S.; Malherbe, J. B.; Prinsloo, L.; Langa, D. F.; Wendler, E.

    2016-03-01

    Glassy carbon samples were implanted with 200 keV strontium ions to a fluence of 2 × 1016 ions/cm2 at room temperature. Analysis with Raman spectroscopy showed that ion bombardment amorphises the glassy carbon structure. Partial recovery of the glassy carbon structure was achieved after the implanted sample was vacuum annealed at 900 °C for 1 h. Annealing the strontium ion bombarded sample at 2000 °C for 5 h resulted in recovery of the glassy carbon substrate with the intensity of the D peak becoming lower than that of the pristine glassy carbon. Rutherford backscattering spectroscopy (RBS) showed that the implanted strontium diffused towards the surface of the glassy carbon after annealing the sample at 900 °C. This diffusion was also accompanied by loss of the implanted strontium. Comparison between the as-implanted and 900 °C depth profiles showed that less than 30% of the strontium was retained in the glassy carbon after heat treatment at 900 °C. The RBS profile after annealing at 2000 °C indicated that no strontium ions were retained after heat treatment at this temperature.

  13. Growth, characterization and dielectric property studies of gel grown barium succinate single crystals

    Indian Academy of Sciences (India)

    M P Binitha; P P Pradyumnan

    2014-05-01

    Single crystals of barium succinate (BaC4H4O4) were grown in silica gel medium using controlled chemical reaction method. Plate-like single crystals of size up to 3 × 2 × 0.2 mm3 was obtained. Single crystal X-ray diffraction (XRD) studies confirmed that structure of the title compound is tetragonal. Powder X-ray diffraction (PXRD) pattern of the grown crystal and the Fourier transform infrared (FT–IR) spectrum in the range 400–4000 cm-1 are recorded. The vibrational bands corresponding to different functional groups are assigned. Thermal stability of the grown crystals is confirmed by differential scanning calorimetry (DSC). Dielectric constant and dielectric loss have been calculated and discussed as a function of frequency at different temperatures.

  14. Low-temperature anharmonicity of barium titanate: A path-integral molecular-dynamics study

    Science.gov (United States)

    Geneste, Grégory; Dammak, Hichem; Hayoun, Marc; Thiercelin, Mickael

    2013-01-01

    We investigate the influence of quantum effects on the dielectric and piezoelectric properties of barium titanate in its (low-temperature) rhombohedral phase, and show the strongly anharmonic character of this system even at low temperature. For this purpose, we perform path-integral molecular-dynamics simulations under fixed pressure and fixed temperature, using an efficient Langevin thermostat-barostat, and an effective Hamiltonian derived from first-principles calculations. The quantum fluctuations are shown to significantly enhance the static dielectric susceptibility (≈ by a factor of 2) and the piezoelectric constants, reflecting the strong anharmonicity of this ferroelectric system even at very low temperature. The slow temperature-evolution of the dielectric properties observed below ≈100 K is attributed (i) to zero-point energy contributions and (ii) to harmonic behavior if the quantum effects are turned off.

  15. Room temperature optical and dielectric properties of Ca and Ni doped barium ferrite

    Science.gov (United States)

    Agrawal, Shraddha; Parveen, Azra; Azam, Ameer

    2016-05-01

    The citrate sol gel combustion method has been used to synthesize (Ba0.9Ca0.1) (Fe0.8 Ni0.2)12O19 hexaferrites. Microstructural analyses were carried out by XRD and FTIR. Optical properties were studied by UV-visible technique in the range of 300-800 nm. The energy band gap was calculated with the help of Tauc relationship shows increases in band gap. Ca and Ni doped barium ferrite annealed at 850°C exhibit significant dispersion in complex permeability. The dispersion in complex dielectric constant can be explained on the basis of Koop's theory based on Maxwell-Wagner two layer models in studied nanoparticles.

  16. Batch kinetics, isotherm and thermodynamic studies of adsorption of strontium from aqueous solutions onto low cost rice-straw based carbons.

    Directory of Open Access Journals (Sweden)

    S. M. Yakout

    2010-09-01

    Full Text Available Present study explored the feasibility of using waste rice-straw based carbons as adsorbent for the removal of strontium under different experimental conditions. The batch sorption is studied with respect to solute concentration (2.8 - 110 mg/L, contact time, adsorbent dose (2.5 - 20 g/L and solution temperature (25 - 55oC. The Langmuir and Dubinin-Radushkevich adsorption models were applied to experimental equilibrium data and isotherm constants were calculated using linear regression analysis. A comparison of kinetic models applied to the adsorption of strontium on rice-straw carbon was evaluated for the pseudo-second-order, Elovich, intraparticle diffusion and Bangham’s kinetics models. The experimental data fitted very well the pseudosecond-order kinetic model and also followed by intra-particle diffusion model, whereas diffusion is not only the rate-controlling step. The results show that the sorption capacity increases with an increase in solution temperature from 25 to 55 oC. The thermodynamics parameters were evaluated. The positive value of ΔH (40.93 kJ indicated that the adsorption of strontium onto RS1 carbon was endothermic, which result was supported by the increasing adsorption of strontium with temperature. The positive value of ΔS (121.8 kJ/mol reflects good affinity of strontium ions towards the rice-straw based carbons. The results have establishedgood potentiality for the carbons particles to be used as a sorbent for the removal of strontium from wastewater.

  17. Ion exchange equilibrium constants

    CERN Document Server

    Marcus, Y

    2013-01-01

    Ion Exchange Equilibrium Constants focuses on the test-compilation of equilibrium constants for ion exchange reactions. The book first underscores the scope of the compilation, equilibrium constants, symbols used, and arrangement of the table. The manuscript then presents the table of equilibrium constants, including polystyrene sulfonate cation exchanger, polyacrylate cation exchanger, polymethacrylate cation exchanger, polysterene phosphate cation exchanger, and zirconium phosphate cation exchanger. The text highlights zirconium oxide anion exchanger, zeolite type 13Y cation exchanger, and

  18. Barium Ferrite Films Grown By Pulsed Laser Ablation

    NARCIS (Netherlands)

    Lisfi, A.; Lodder, J.C.; Haan, de P.; Roesthuis, F.J.G.

    1998-01-01

    Abstract available only. It is known that barium ferrite (BaFe12019) can grow with perpendicular anisotropy on A1203 a single crystal substrate,' but also on an amorphous substrate by using a ZnO buffer.2 Because of its large magnetic anisotropy which can easily overcome the shape anisotropy of the

  19. The Kerr nonlinearity of the beta-barium borate crystal

    DEFF Research Database (Denmark)

    Bache, Morten; Guo, Hairun; Zhou, Binbin

    2013-01-01

    A popular crystal for ultrafast cascading experiments is beta-barium-borate (β-BaB2O4, BBO). It has a decent quadratic nonlinear coefficient, and because the crystal is anisotropie it can be birefringence phase-matched for type I (oo → e) second-harmonic generation (SHG). For femtosecond...

  20. Magnetoelastic coupling in epitaxial cobalt ferrite/barium titanate heterostructures

    Energy Technology Data Exchange (ETDEWEB)

    Gräfe, Joachim; Welke, Martin [Wilhelm-Ostwald-Institut für Physikalische und Theoretische Chemie, Universität Leipzig, Linnéstraße 2, 04103 Leipzig (Germany); Bern, Francis; Ziese, Michael [Institut für Experimentelle Physik II, Universität Leipzig, Linnéstraße 5, 04103 Leipzig (Germany); Denecke, Reinhard, E-mail: denecke@uni-leipzig.de [Wilhelm-Ostwald-Institut für Physikalische und Theoretische Chemie, Universität Leipzig, Linnéstraße 2, 04103 Leipzig (Germany)

    2013-08-15

    Ultra-thin cobalt ferrite films have been synthesised on ferroelectric barium titanate crystals. The cobalt ferrite films exhibit a magnetic response to strain induced by structural changes in the barium titanate substrate, suggesting a pathway to multiferroic coupling. These structural changes are achieved by heating through the phase transition temperatures of barium titanate. In addition the ferromagnetic signal of the substrate itself is taken into account, addressing the influence of impurities or defects in the substrate. The cobalt ferrite/barium titanate heterostructure is a suitable oxidic platform for future magnetoelectric applications with an established ferroelectric substrate and widely tuneable magnetic properties by changing the transition metal in the ferrite film. - Highlights: ► Ultra-thin CoFe{sub 2}O{sub 4} films grown on ferroelectric BaTiO{sub 3} crystals by PLD. ► Magnetic response to structural changes of BaTiO{sub 3} at transition temperatures. ► Significant magneto-elastic coupling of in-plane magnetisation in SQUID experiments. ► Clear distinction between contribution by BaTiO{sub 3} substrate and by CoFe{sub 2}O{sub 4} film.

  1. Excitation energies of barium oxide bands measured in flames

    NARCIS (Netherlands)

    Hurk, J. van der; Hollander, Tj.; Alkemade, C.T.J.

    1975-01-01

    Experiments are described that yield additional information about the excitation energy of visible barium oxide bands appearing in flames. Excitation energy differences are derived directly from the ratios of thermal band intensities as a function of temperature and agree with the value calculated f

  2. CNO and F abundances in the barium star HD 123396

    CERN Document Server

    Alves-Brito, Alan; Yong, David; Meléndez, Jorge; Vásquez, Sergio

    2011-01-01

    [Abridged] Barium stars are moderately rare chemically peculiar objects which are believed to be the result of the pollution of an otherwise normal star by material from an evolved companion on the asymptotic giant branch (AGB). We aim to derive carbon, nitrogen, oxygen, and fluorine abundances for the first time from infrared spectra of the barium red giant star HD 123396 to quantitatively test AGB nucleosynthesis models for producing barium stars via mass accretion. High-resolution and high S/N infrared spectra were obtained using the Phoenix spectrograph mounted at the Gemini South telescope. The abundances were obtained through spectrum synthesis of individual atomic and molecular lines, using the MOOG stellar line analysis program together with Kurucz's stellar atmosphere models. The analysis was classical, using 1D stellar models and spectral synthesis under the assumption of local thermodynamic equilibrium. We confirm that HD 123396 is a metal-deficient barium star ([Fe/H] = -1.05), with A(C) = 7.88, A...

  3. Barium titanate inverted opals-synthesis, characterization, and optical properties

    Energy Technology Data Exchange (ETDEWEB)

    Soten, I.; Miguez, H.; Yang, S.M.; Petrov, S.; Coombs, N.; Tetreault, N.; Ozin, G.A. [Toronto Univ., ON (Canada). Dept. of Chemistry; Matsuura, N.; Ruda, H.E. [Toronto Univ., ON (Canada). Dept. of Metallurgy and Materials Science

    2002-01-01

    The engineering of cubic or tetragonal polymorphs of nanocrystalline barium titanate inverted opals has been achieved by thermally induced transformations. Optical characterization demonstrated photonic crystal behavior of the opals. The tuning of the ferroelectric-paraelectric transition around the Curie temperature is shown in this paper. (orig.)

  4. Synthesis of Nanocrystalline Barium Ferrite in Ethanol/Water Media

    Institute of Scientific and Technical Information of China (English)

    M.Montazeri-Pour; A.Ataie

    2009-01-01

    Nanocrystalline particles of barium ferrite magnetic material have been prepared by co-precipitation route using aqueous and non-aqueous solutions of iron and barium chlorides with a Fe/Ba molar ratio of 11 and subsequent drying-annealing treatment. Water and ethanol/water mixture with volume ratio of 3:1 were used as solvents in the process. Coprecipitated powders were annealed at various temperatures for 1 h. FTIR (Fourier transform infrared spectroscopy), XRD (X-ray diffraction), DTA/TGA (differential thermal analy-sis/thermogravimetric analysis) and SEM (scanning electron microscopy) techniques were used to evaluate powder particle characteristics. DTA/TGA results confirmed by those obtained from XRD indicated that the formation of barium ferrite occurs in sample synthesized in ethanol/water solution at a relatively low temperature of 631℃. Nano-size particles of barium ferrite with mean particle size of almost 75 and 100 nm were observed in the SEM micrographs of the samples synthesized in ethanol/water solution after annealing at 700 and 800℃ for 1 h, respectively.

  5. Strontium-90 at the Hanford Site and its ecological implications

    Energy Technology Data Exchange (ETDEWEB)

    RE Peterson; TM Poston

    2000-05-22

    Strontium-90, a radioactive contaminant from historical operations at the U.S. Department of Energy (DOE) Hanford Site, enters the Columbia River at several locations associated with former plutonium production reactors at the Site. Strontium-90 is of concern to humans and the environment because of its moderately long half-life (29.1 years), its potential for concentrating in bone tissue, and its relatively high energy of beta decay. Although strontium-90 in the environment is not a new issue for the Hanford Site, recent studies of near-river vegetation along the shoreline near the 100 Areas raised public concern about the possibility of strontium-90-contaminated groundwater reaching the riverbed and fall chinook salmon redds. To address these concerns, DOE asked Pacific Northwest National Laboratory (PNNL) to prepare this report on strontium-90, its distribution in groundwater, how and where it enters the river, and its potential ecological impacts, particularly with respect to fall chinook salmon. The purpose of the report is to characterize groundwater contaminants in the near-shore environment and to assess the potential for ecological impact using salmon embryos, one of the most sensitive ecological indicators for aquatic organisms. Section 2.0 of the report provides background information on strontium-90 at the Hanford Site related to historical operations. Public access to information on strontium-90 also is described. Section 3.0 focuses on key issues associated with strontium-90 contamination in groundwater that discharges in the Hanford Reach. The occurrence and distribution of fall chinook salmon redds in the Hanford Reach and characteristics of salmon spawning are described in Section 4.0. Section 5.0 describes the regulatory standards and criteria used to set action levels for strontium-90. Recommendations for initiating additional monitoring and remedial action associated with strontium-90 contamination at the Hanford Site are presented in Section 6

  6. Cosmological Constant, Fine Structure Constant and Beyond

    CERN Document Server

    Wei, Hao; Li, Hong-Yu; Xue, Dong-Ze

    2016-01-01

    In this work, we consider the cosmological constant model $\\Lambda\\propto\\alpha^{-6}$, which is well motivated from three independent approaches. As is well known, the evidence of varying fine structure constant $\\alpha$ was found in 1998. If $\\Lambda\\propto\\alpha^{-6}$ is right, it means that the cosmological constant $\\Lambda$ should be also varying. In this work, we try to develop a suitable framework to model this varying cosmological constant $\\Lambda\\propto\\alpha^{-6}$, in which we view it from an interacting vacuum energy perspective. We propose two types of models to describe the evolutions of $\\Lambda$ and $\\alpha$. Then, we consider the observational constraints on these models, by using the 293 $\\Delta\\alpha/\\alpha$ data from the absorption systems in the spectra of distant quasars, and the data of type Ia supernovae (SNIa), cosmic microwave background (CMB), baryon acoustic oscillation (BAO). We find that the model parameters can be tightly constrained to the narrow ranges of ${\\cal O}(10^{-5})$ t...

  7. Effects of strontium and boron interactions in Al-7Si alloys

    Directory of Open Access Journals (Sweden)

    Chen Xiang

    2010-11-01

    Full Text Available Effects of boron and strontium combined treatment on the microstructure of hypoeutectic Al-7Si alloy have been studied. Experimental results show that strontium has no significant effect on the grain refinement efficiency of boron and the eutectic silicon modification efficiency is not only related to the strontium content but also related to the boron content in the Al-7Si alloy melt. There is a negative interaction between boron and strontium that results in the formation of a strontium-boron-aluminum containing compound, which reduces the effective strontium level and decreases the eutectic silicon modification efficiency substantially. The refinement and modification mechanisms remain unchanged after the combined addition of strontium and boron. Based on the experimental results, a model for assessing the modification level in the Al-Si alloy melts after combined addition of boron and strontium was presented.

  8. Stable strontium isotopic ratios from archaeological organic remains from the Thorsberg peat bog

    DEFF Research Database (Denmark)

    Nosch, Marie-Louise Bech; von Carnap-Bornheim, Claus; Grupe, Gisela;

    2007-01-01

    Pilot study analysing stable strontium isotopic ratios from Iron Age textile and leather finds from the Thorsberg peat bog.......Pilot study analysing stable strontium isotopic ratios from Iron Age textile and leather finds from the Thorsberg peat bog....

  9. Eu(2+) luminescence in strontium aluminates.

    Science.gov (United States)

    Dutczak, D; Jüstel, T; Ronda, C; Meijerink, A

    2015-06-21

    The luminescence properties of Eu(2+) doped strontium aluminates are reported and reviewed for a variety of aluminates, viz. SrAl12O19, SrAl4O7, Sr4Al14O25, SrAl2O4 and Sr3Al2O6. The aim of the research is to investigate the role of local coordination and covalency of the aluminate host lattice, related to the Sr/Al ratio, on the optical properties of the Eu(2+) ion. The UV and VUV excited luminescence spectra as well as luminescence decay curves were recorded to characterize the luminescence properties of the investigated aluminates. The emission of Eu(2+) ions varies over a wide spectral range, from ultraviolet (UV) to red, for the series of aluminates. The variation in emission color can be related to the crystal-field splitting of the 5d levels and the covalent interaction with the surrounding oxygen anions. In the least covalent material, viz. SrAl12O19:Eu(2+), narrow line emission due to the (6)P7/2-(8)S7/2 transition occurs at 4 K, indicating that the 4f(6)5d excited state is situated above the (6)P7/2(4f(7)) excited state around 360 nm. The most alkaline material, viz. Sr3Al2O6:Eu(2+) is the most covalent host and exhibits several d-f emission bands in the yellow to red spectral range due to the Eu(2+) ions located on different crystallographic Sr(2+) sites. The Eu(2+) emission spectra in the other aluminates confirm the trend that with increasing Sr/Al ratio the Eu(2+) emission shifts to longer wavelengths. Interesting differences are observed for the Eu(2+) from different crystallographic sites which cannot always be related with apparent differences in the first oxygen coordination sphere. The discussion gives insight into how in a similar class of materials, strontium aluminates, the emission color of Eu(2+) can be tuned over a wide spectral region.

  10. Radiopaque strontium fluoroapatite glass-ceramics

    Directory of Open Access Journals (Sweden)

    Wolfram eHöland

    2015-10-01

    Full Text Available The controlled precipitation of strontium fluoroapatite crystals, was studied in four base glass compositions derived from the SiO2 – Al2O3 – Y2O3 – SrO – Na2O – K2O/Rb2O/Cs2O – P2O5 – F system. The crystal phase formation of these glasses and the main properties of the glass-ceramics, such as thermal and optical properties and radiopacity were compared with a fifth, a reference glass-ceramic. The reference glass-ceramic was characterized as Ca-fluoroapatite glass-ceramic. The four strontium fluoroapatite glass-ceramics showed the following crystal phases: a Sr5(PO43F – leucite, KAlSi2O6 , b Sr5(PO43F – leucite, KAlSi2O6, and nano-sized NaSrPO4 c Sr5(PO43F – pollucite, CsAlSiO4 , and nano-sized NaSrPO4, d Sr5(PO43F – Rb-leucite, RbAlSi2O6, and nano-sized NaSrPO4.The proof of crystal phase formation was possible by X-ray diffraction (XRD. The microstructures, which were studied using scanning electron microscopy (SEM demonstrated a uniform distribution of the crystals in the glass matrix. The Sr-fluoroapatites were precipitated based on an internal crystallization process, and the crystals demonstrated a needlelike morphology. The study of the crystal growth of needlelike Sr-fluoroapatites gave a clear evidence of an Ostwald ripening mechanism.The formation of leucite, pollucite and Rb-leucite was based on a surface crystallization mechanism. Therefore, a twofold crystallization mechanism was successfully applied to develop these types of glass-ceramics. The main focus of this study was the controlled development of glass-ceramics exhibiting high radiopacity in comparison to the reference glass-ceramic. This goal could be achieved with all four glass-ceramics with the preferred development of the Sr-fluoroapatite – pollucite-type glass-ceramic. In addition to this main development, it was possible to control the thermal properties. Especially the Rb-leucite containing glass-ceramic showed the highest coefficient of thermal

  11. Structural and dielectric characteristics of strontium tetraborate-bismuth vanadate glass-ceramics

    Energy Technology Data Exchange (ETDEWEB)

    Varma, K.B.R.; Shankar, M.V.; Subbanna, G.N. [Indian Inst. of Science (India). Materials Research Centre

    1996-05-01

    Glasses of strontium tetraborate, containing up to 50 mole-percent bismuth vanadate [(1{minus}x)SBO-xBiV (x = 0 to 0.50)], were prepared by splat quenching method. The glassy nature of these samples was confirmed by differential thermal analysis (DTA). The glass transition temperature (T{sub g}) and the crystallization temperature (T{sub cr}) of the glasses decrease with increase in bismuth vanadate, Bi{sub 2}VO{sub 5.5} (BiV) content. High resolution transmission electron microscopic studies reveal the presence of spherical particles of amorphous BiV (less than 10 nm in size) dispersed in the glassy matrix of strontium tetraborate, SrB{sub 4}O{sub 7} (SBO). The glasses of the compositions x = 0.25 to 0.50, on annealing at 500 C (T{sub g}) gave rise to crystalline BiV phase. Physical properties such as density, dielectric and optical transmission of these SBO:BiV glass-ceramics have been studied. The dielectric constant ({epsilon}{sub r}) of these glass-ceramics increases with increasing BiV content. The measured {epsilon}{sub r} values are found to be in good agreement with those predicted by the logarithmic mixture rule.

  12. [Cytotoxicity of the strontium-substituted hydroxyapatite evaluated by MTT colorimetry].

    Science.gov (United States)

    Fu, Y; Chen, D; Zhang, J

    2001-09-01

    This study was conducted to evaluate the cytotoxicity of strontium-substituted hydroxyapatite by methyl thiazolyl tetrazolium (MTT) colorimetry. We used the MTT method to assay the cytotoxicity of the strontium-substituted hydroxyapatite containing different strontium concentrations (1%, 5%, 10%, 100% Sr2+) and the pure hydroxyapatite. The results showed that the cytotoxicity scores of the different materials were grade 0 or grade 1. These led us to the conclusion that strontium-substituted hydroxyapatite has good biocompatibility.

  13. STRONTIUM-90 LIQUID CONCENTRATION SOLUBILITY CORRELATION IN THE HANFORD TANK WASTE OPERATIONS SIMULATOR

    Energy Technology Data Exchange (ETDEWEB)

    HOHL, T.; PLACE, D.; WITTMAN, R.

    2004-08-05

    A new correlation was developed to estimate the concentration of strontium-90 in a waste solution based on total organic carbon. This correlation replaces the strontium-90 wash factors, and when applied in the Hanford Tank Waste Operations Simulator, significantly reduced the estimated quantity of strontium-90 in the delivered low-activity waste feed. This is thought to be a more realistic estimate of strontium-90 than using the wash-factor method.

  14. [Mechanisms of neurotransmitter release facilitation in strontium solutions].

    Science.gov (United States)

    Mukhamed'iarov, M A; Kochunova, Iu O; Telina, E N; Zefirov, A L

    2008-02-01

    Mechanisms of neurotransmitter release facilitation were studied using electrophysiological recording of end-plate currents (EPC) and nerve ending (NE) responses after substitution of extracellular Ca ions with Sr ions at the frog neuromuscular junction. The solutions with 0.5 mM concentration of Ca ions (calcium solution) or 1 mM concentration of Sr ions (strontium solution) were used where baseline neurotransmitter release (at low-frequency stimulation) is equal. Decay of paired-pulse facilitation of EPC at calcium solutions with increase of interpulse interval from 5 to 500 ms was well described by three-exponential function consisting of early, first and second components. Facilitation at strontium solutions was significantly diminished due mainly to decrease of early and first components. At the same time, EPC facilitation with rhythmic stimulation (10 or 50 imp/s) at strontium solutions was significantly increased. Also more pronounced decrease of NE response 3rd phase, reflecting potassium currents was detected under rhythmic stimulation of 50 imp/s at strontium solutions comparing to calcium solutions. It was concluded that facilitation sites underlying first and early components had lower affinity to Sr ions than to Ca ions. The enhancement of frequency facilitation at strontium solutions is mediated by two mechanisms: more pronounced broadening of NE action potential and increase of bivalent cation influx due to feebly marked activation of Ca(2+)-dependent potassium current by Sr ions, and slower dynamics of Sr(2+) removal from NE axoplasm comparing to Ca(2+).

  15. Surface functionalization with strontium-containing nanocomposite coatings via EPD.

    Science.gov (United States)

    Ma, Kena; Huang, Dan; Cai, Jing; Cai, Xinjie; Gong, Lingling; Huang, Pin; Wang, Yining; Jiang, Tao

    2016-10-01

    Metal orthopedic implants still face challenges in some compromised conditions, partly due to bio-inertness. The present study aimed to functionalize metallic implants with organic-inorganic nanocomposite (strontium-containing chitosan/gelatin) coatings through a simple single-step electrophoretic deposition under mild conditions. The surface characterization and in vitro cellular response were studied and compared with chitosan/gelatin (CS/G) coatings. SEM images suggested the inorganic nanoparticles may be encapsulated within or mixed with organic polymers. The XRD patterns showed that strontium carbonate was generated in the coatings. The TEM images revealed strontium-containing nanoparticles were released from the coatings in PBS. The continuous release after the initial burst release ensured the enduring effects of the functionalized surface. The tensile bond strength of the coatings to the substrates increased after the addition of strontium. In vitro cellular study confirmed that strontium-containing coatings supported the proliferation of MC3T3-E1 cells and exhibited excellent ability to enhance the differentiation of such pre-osteoblasts. Therefore, such organic-inorganic nanocomposite coatings are a promising candidate to functionalize orthopedic implant surfaces.

  16. Spectroscopy and Laser-SNMS on stable and radioactive strontium

    Energy Technology Data Exchange (ETDEWEB)

    Bosco, Hauke; Walther, Clemens [Institut fuer Radiooekologie und Strahlenschutz, Leibniz Universitaet Hannover (Germany); Franzmann, Michael [Institut fuer Radiooekologie und Strahlenschutz, Leibniz Universitaet Hannover (Germany); Institut fuer Physik, Johannes Gutenberg Universitaet Mainz (Germany); Kron, Tobias; Wendt, Klaus [Institut fuer Physik, Johannes Gutenberg Universitaet Mainz (Germany)

    2016-07-01

    Nuclear accidents as experienced e.g. in Chernobyl or Fukushima and nuclear weapon tests released considerable activity levels and a variety of medium to long-lived radionuclides into the environment. Strontium-90 appears as a significant share of the fission products in spent nuclear fuel and correspondingly in any possible release. Due to its chemical properties it is subject to long range transport through the environment and can cause considerable dose to man when entering the food chain. Correspondingly, the investigation of speciation and migration channels is of major relevance. A radioanalytical approach is severely hampered by the low beta energy of the strontium-90 decay and the need to separate strontium-90 from the secular equilibrated daughter yttrium-90. Hence, application of a mass spectrometric method without chemical separation of the elements is a promising alternative for low-level investigation of strontium-90. Application of the new Laser-SNMS system at IRS Hannover could well suit those needs. It applies three Ti:Sa lasers for resonant ionization of neutral atoms produced by primary ion sputtering in a SIMS together with a time-of-flight mass analysis which provides high spatial resolution. The analytical measurements are preceded by spectroscopic studies on the level structure of strontium to develop a most efficient ionization scheme.

  17. Strontium-Containing Apatite/Poly Lactide Composites Favoring Osteogenic Differentiation and in Vivo Bone Formation

    NARCIS (Netherlands)

    Luo, Xiaoman; Barbieri, D.; Zhang, Yunfei; Yan, Yonggang; Bruijn, de Joost D.; Yuan, Huipin

    2015-01-01

    Strontium was shown to enhance bone growth; however, its oral administration may lead to severe side effects. The application of strontium in orthopedic biomaterials may therefore be an alternative to achieve targeted and sustained strontium treatment to the surgery site in aid of bone growth locall

  18. 40 CFR 721.10008 - Manganese strontium oxide (MnSrO3).

    Science.gov (United States)

    2010-07-01

    ... 40 Protection of Environment 30 2010-07-01 2010-07-01 false Manganese strontium oxide (MnSrO3... Specific Chemical Substances § 721.10008 Manganese strontium oxide (MnSrO3). (a) Chemical substance and significant new uses subject to reporting. (1) The chemical substance identified as manganese strontium...

  19. Regeneration of barium carbonate from barium sulphide in a pilot-scale bubbling column reactor and utilization for acid mine drainage

    CSIR Research Space (South Africa)

    Mulopo, J

    2012-01-01

    Full Text Available Batch regeneration of barium carbonate (BaCO3) from barium sulphide (BaS) slurries by passing CO2 gas into a pilot-scale bubbling column reactor under ambient conditions was used to assess the technical feasibility of BaCO3 recovery in the Alkali...

  20. Generalized Pickands constants

    NARCIS (Netherlands)

    Debicki, K.G.

    2001-01-01

    Pickands constants play an important role in the exact asymptotic of extreme values for Gaussian stochastic processes. By the {it generalized Pickands constant ${cal H_{eta$ we mean the limit begin{eqnarray* {cal H_{eta= lim_{T to inftyfrac{ {cal H_{eta(T){T, end{eqnarray* where ${cal H_{eta(T)= Exp

  1. Design, testing, fabrication and launch support of a liquid chemical barium release payload (utilizing the liquid fluorine-barium salt/hydrazine system)

    Science.gov (United States)

    Stokes, C. S.; Smith, E. W.; Murphy, W. J.

    1972-01-01

    A payload was designed which included a cryogenic oxidizer tank, a fuel tank, and burner section. Release of 30 lb of chemicals was planned to occur in 2 seconds at the optimum oxidizer to fuel ratio. The chemicals consisted of 17 lb of liquid fluorine oxidizer and 13 lb of hydrazine-barium salt fuel mixture. The fuel mixture was 17% barium chloride, 16% barium nitrate, and 67% hydrazine, and contained 2.6 lb of available barium. Two significant problem areas were resolved during the program: explosive valve development and burner operation. The release payload was flight tested, from Wallops Island, Virginia. The release took place at an altitude of approximately 260 km. The release produced a luminous cloud which expanded very rapidly, disappearing to the human eye in about 20 seconds. Barium ion concentration slowly increased over a wide area of sky until measurements were discontinued at sunrise (about 30 minutes).

  2. Microstructure of pre-sintered permanent magnetic strontium ferrite powder

    Institute of Scientific and Technical Information of China (English)

    YU Hongya; LIU Zhengyi; ZENG Dechang

    2006-01-01

    The microstructure and characteristics of pre-sintered strontium ferrite powderwere investigated by X-ray diffraction, scanning electron microscopy and transmission electron microscopy. The present study shows that the pre-sintered strontium ferrite powder is provided with a certain particle size distribution, which results in high-density magnets. The strontium ferrite particle has a laminar hexagonal structure with a size similar to ferrite single domain. Ferric oxidephase due to an incomplete solid phase reaction in the first sintering is discovered, which will deteriorate the magnetic properties of ferrite magnet. In addition, the waste ferrite magnets with needle shape arranging along C axis in good order into the powders are found, which have no negative effects on finished product quality.

  3. Energy dependence of radioluminescence spectra from strontium titanate

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Y., E-mail: wyfemail@gmail.com [School of Science, China University of Geosciences, Beijing 100083 (China); Zhao, Y.; Zhang, Z.; Zhao, C.; Wu, X. [School of Science, China University of Geosciences, Beijing 100083 (China); Finch, A.A. [Department of Earth & Environmental Sciences, University of St. Andrews, Fife KY16 9AL (United Kingdom); Townsend, P.D. [Physics Building, University of Sussex, Brighton BN1 9QH (United Kingdom)

    2015-10-15

    X-ray excited luminescence spectra of strontium titanate are reported over the temperature range from 20 to 300 K. The range includes several crystalline phases, each with different emission spectra. The signals are thermally quenched above ~220 K. There are spectral shifts and intensity changes around the temperatures associated with phase changes and overall there are nominally three spectral emission bands. A remarkable observation is that at fixed lower temperatures the spectra undergo major changes with the energy of the X-rays. A possible cause of the effect is discussed in terms of inner shell excitation from the K shell of the strontium. Comparisons with thermoluminescence spectra from the strontium titanate are reported. - Highlights: • Radioluminescence spectra of SrTiO{sub 3} are reported from 20 to 300 K. • X-ray luminescence spectra depend on crystal phase. • Direct evidence for inner shell excitation of Sr controlling emission spectra.

  4. Studies of Ultracold Strontium Atoms in an Optical Dipole Trap

    Science.gov (United States)

    Traverso, A. J.; Martinez de Escobar, Y. N.; Mickelson, P. G.; Killian, T. C.

    2008-05-01

    We survey recent experiments with ultracold strontium performed in our group. Trapping and cooling occurs in three stages: successive magneto-optical traps (MOTs) operating on 461 nm and 689 nm transitions of strontium, respectively, are loaded to cool atoms to a temperature of 1 μK. Finally, atoms are loaded into a far-off-resonance optical dipole trap (ODT). We examine the loading characteristics, thermalization, and lifetime of atoms held within the ODT. We also perform spectroscopy of atoms held within the ODT. During laser cooling, we are able to manipulate the energy levels of the atoms and shelve them into metastable states using 707 nm and 3 μm lasers. These experiments reveal interesting physics of ultracold strontium.

  5. Stark spectrum of barium in highly excited Rydberg states

    Institute of Scientific and Technical Information of China (English)

    Yang Hai-Feng; Gao Wei; Cheng Hong; Liu Xiao-Jun; Liu Hong-Ping

    2013-01-01

    We present observations of Stark spectra of barium in highly excited Rydberg states in the energy region around n =35.The one-photon excitation concerns the π transition.The observed Stark spectra at electric fields ranging from 0 to 60 V·cm-1 are well explained by the diagonalization of the Hamiltonian incorporating the core effects.From the Stark maps,the anti-crossings between energy levels are identified experimentally and theoretically.The time of flight spectra at the specified Stark states are recorded,where the deceleration and acceleration of barium atoms are observed.This is very consistent with the prediction derived from the Stark maps from the point of view of energy conservation.

  6. HYBRID AND CHARACTERISTIC OF POLYANILINE- BARIUM TITANATE NANOCOMPOSITE PARTICLES

    Institute of Scientific and Technical Information of China (English)

    2000-01-01

    Polyaniline-barium titanate (PAn-BaTiO3) ultrafine composite particles were prepared by the oxidative polymerization of aniline with H2O2 while barium titanate nanoparticles were synthesized with a sol-gel method. The infrared spectrogram shows that the polymerization of PAn in the hybrid process of PAn-BaTiO3 is similar with the polymeric process of pure aniline, and there is interaction of PAn and BaTiO3 in the PAn-BaTiO3. SEM and TEM results show that the average diameter of the composite particles is 1.50 μm and the diameters of BaTiO3 nanoparticles are 5-15 nm in the composite particle. The electrical conductivity of the ultrafine composite particles is transformable from 100 to 10-11S/cm by equilibrium doping or dedoping method using various concentration of HCl or NaOH solutions.

  7. Electromagnetic properties of carbon black and barium titanate composite materials

    Energy Technology Data Exchange (ETDEWEB)

    Wang Guiqin [School of Material Science and Engineering, Dalian University of Technology, Dalian 116023 (China)], E-mail: c2b2chen@163.com; Chen Xiaodong; Duan Yuping; Liu Shunhua [School of Material Science and Engineering, Dalian University of Technology, Dalian 116023 (China)

    2008-04-24

    Nanocrystalline carbon black/barium titanate compound particle (CP) was synthesized by sol-gel method. The phase structure and morphology of compound particle were investigated by X-ray diffraction (XRD), transmission electron microscope (TEM) and Raman spectrum measurements, the electroconductivity was test by trielectrode arrangement and the precursor powder was followed by differential scanning calorimetric measurements (DSC) and thermal gravimetric analysis (TGA). In addition, the complex relative permittivity and permeability of compound particle were investigated by reflection method. The compound particle/epoxide resin composite (CP/EP) with different contents of CP were measured. The results show barium titanate crystal is tetragonal phase and its grain is oval shape with 80-100 nm which was coated by carbon black film. As electromagnetic (EM) complex permittivity, permeability and reflection loss (RL) shown that the compound particle is mainly a kind of electric and dielectric lossy materials and exhibits excellent microwave absorption performance in the X- and Ku-bands.

  8. Particularities of Radiation Defect Formation in Ceramic Barium Cerate

    Science.gov (United States)

    Khromushin, I. V.; Aksenova, T. I.; Tuseev, T.; Munasbaeva, K. K.; Ermolaev, Yu V.; Ermolaev, V. N.; Seitov, A. S.

    2015-04-01

    The effects of irradiation with electrons, ions of noble gases (Ne, Ar, Kr) and oxygen on the structure and properties of neodymium-doped barium cerate have been studied using the methods of X-ray diffraction analysis, scanning electron and atomic force microscopy, thermal desorption spectroscopy. It was shown that irradiation by low-energy ions of noble gases stimulates the blistering processes on the sample surface, while the high-energy ions contribute to formation of the structures on the irradiated surface that resemble the various stages of spherulitegrowth. The similar structures were not observed in the case of irradiation with high-energy oxygen ions. According to the data on thermal desorption of water and oxygen molecules from the irradiated barium cerate it was supposed that irradiation by the noble gas ions promotes neodymium oxidation state change. It was noticed that the electron irradiation leads to the formation of the nano-sized acicular structures on the cerate surface.

  9. Acute barium intoxication following ingestion of soap water solution

    Directory of Open Access Journals (Sweden)

    Nandita Joshi

    2012-01-01

    Full Text Available We present a rare case in which a young girl ingested a solution of a hair-removing soap. The ingestion resulted in profound hypokalemia and severe acidosis leading to flaccid paralysis, respiratory arrest and ventricular arrhythmias. Ultimately the patient made complete recovery. The soapwas found to contain barium sulfide. The degree of paralysis and acidosis appeared to be directly related to serum potassium levels.

  10. Barium isotopes reveal role of ocean circulation on barium cycling in the Atlantic

    Science.gov (United States)

    Bates, Stephanie L.; Hendry, Katharine R.; Pryer, Helena V.; Kinsley, Christopher W.; Pyle, Kimberley M.; Woodward, E. Malcolm S.; Horner, Tristan J.

    2017-05-01

    We diagnose the relative influences of local-scale biogeochemical cycling and regional-scale ocean circulation on Atlantic barium cycling by analysing four new depth profiles of dissolved Ba concentrations and isotope compositions from the South and tropical North Atlantic. These new profiles exhibit systematic vertical, zonal and meridional variations that reflect the influence of both local-scale barite cycling and large-scale ocean circulation. Epipelagic decoupling of dissolved Ba and Si reported previously in the tropics is also found to be associated with significant Ba isotope heterogeneity. As such, we contend that this decoupling originates from the depth segregation of opal and barite formation but is exacerbated by weak vertical mixing. Zonal influence from isotopically-'heavy' water masses in the western North Atlantic evidence the advective inflow of Ba-depleted Upper Labrador Sea Water, which is not seen in the eastern basin or the South Atlantic. Meridional variations in Atlantic Ba isotope systematics below 2000 m appear entirely controlled by conservative mixing. Using an inverse isotopic mixing model, we calculate the Ba isotope composition of the Ba-poor northern end-member as +0.45 ‰ and the Ba-rich southern end-member +0.26 ‰, relative to NIST SRM 3104a. The near-conservative behaviour of Ba below 2000 m indicates that Ba isotopes can serve as an independent tracer of the provenance of northern- versus southern-sourced water masses in the deep Atlantic Ocean. This finding may prove useful in palaeoceanographic studies, should appropriate sedimentary archives be identified, and offers new insights into the processes that cycle Ba in seawater.

  11. Strontium and Magnesium in Water and in Crassostrea Calcite.

    Science.gov (United States)

    Lerman, A

    1965-11-05

    Distribution of magnesium and strontium was determined between waters and calcites secreted by the oyster species Crassostrea virginica and C. rhizophorae in natural habitats at eight localities, from Maine to Puerto Rico. The concentration of strontium in the calcite shells increases with increasing temperature in the range 13 degrees to 25 degrees C, and also with increasing Sr(++)/Ca(++) molal ratio in the water. The concentration of magnesium in the shells increases irregularly with temperature, and it is apparently independent of the Mg(++)/Ca(++) ratio in the water. The greater variation with temperature in the distribution factor for magnesium may be related to genetic differences between semi-isolated populations.

  12. Strontium cobaltite oxygen sponge catalyst and methods of use

    Energy Technology Data Exchange (ETDEWEB)

    Lee, Ho Nyung; Jeen, Hyoungjeen; Choi, Woo Seok; Biegalski, Michael; Folkman, Chad M.; Tung, I-Cheng; Fong, Dillon D.; Freeland, John W.; Shin, Dongwon; Ohta, Hiromichi; Chisholm, Matthew F.

    2017-01-24

    Rapid, reversible redox activity may be accomplished at significantly reduced temperatures, as low as about 200.degree. C., from epitaxially stabilized, oxygen vacancy ordered SrCoO.sub.2.5 and thermodynamically unfavorable perovskite SrCoO.sub.3-.delta.. The fast, low temperature redox activity in SrCoO.sub.3-.delta. may be attributed to a small Gibbs free energy difference between the two topotactic phases. Epitaxially stabilized thin films of strontium cobaltite provide a catalyst adapted to rapidly transition between oxidation states at substantially low temperatures. Methods of transitioning a strontium cobaltite catalyst from a first oxidation state to a second oxidation state are described.

  13. ADSORPTION OF STRONTIUM IONS FROM WATER ON MODIFIED ACTIVATED CARBONS

    Directory of Open Access Journals (Sweden)

    Mihai Ciobanu

    2016-12-01

    Full Text Available Adsorption of strontium ions from aqueous solutions on active carbons CAN-7 and oxidized CAN-8 has been studied. It has been found that allure of the adsorption isotherms for both studied active carbons are practically identical. Studies have shown that the adsorption isotherms for strontium ions from aqueous solutions are well described by the Langmuir and Dubinin-Radushkevich equations, respectively. The surface heterogeneity of activated carbons CAN-7 and oxidized CAN-8 has been assessed by using Freundlich equation.

  14. Radiopaque Strontium Fluoroapatite Glass-Ceramics

    Science.gov (United States)

    Höland, Wolfram; Schweiger, Marcel; Dittmer, Marc; Ritzberger, Christian

    2015-01-01

    The controlled precipitation of strontium fluoroapatite crystals was studied in four base glass compositions derived from the SiO2–Al2O3–Y2O3–SrO–Na2O–K2O/Rb2O/Cs2O–P2O5–F system. The crystal phase formation of these glasses and the main properties of the glass-ceramics, such as thermal and optical properties and radiopacity were compared with a fifth, a reference glass-ceramic. The reference glass-ceramic was characterized as Ca-fluoroapatite glass-ceramic. The four strontium fluoroapatite glass-ceramics showed the following crystal phases: (a) Sr5(PO4)3F – leucite, KAlSi2O6, (b) Sr5(PO4)3F – leucite, KAlSi2O6, and nano-sized NaSrPO4, (c) Sr5(PO4)3F – pollucite, CsAlSi2O6, and nano-sized NaSrPO4, and (d) Sr5(PO4)3F – Rb-leucite, RbAlSi2O6, and nano-sized NaSrPO4. The proof of crystal phase formation was possible by X-ray diffraction. The microstructures, which were studied using scanning electron microscopy, demonstrated a uniform distribution of the crystals in the glass matrix. The Sr-fluoroapatites were precipitated based on an internal crystallization process, and the crystals demonstrated a needle-like morphology. The study of the crystal growth of needle-like Sr-fluoroapatites gave a clear evidence of an Ostwald ripening mechanism. The formation of leucite, pollucite, and Rb-leucite was based on a surface crystallization mechanism. Therefore, a twofold crystallization mechanism was successfully applied to develop these types of glass-ceramics. The main focus of this study was the controlled development of glass-ceramics exhibiting high radiopacity in comparison to the reference glass-ceramic. This goal could be achieved with all four glass-ceramics with the preferred development of the Sr-fluoroapatite – pollucite-type glass-ceramic. In addition to this main development, it was possible to control the thermal properties. Especially the Rb-leucite containing glass-ceramic showed the highest coefficient of thermal

  15. Radiopaque Strontium Fluoroapatite Glass-Ceramics.

    Science.gov (United States)

    Höland, Wolfram; Schweiger, Marcel; Dittmer, Marc; Ritzberger, Christian

    2015-01-01

    The controlled precipitation of strontium fluoroapatite crystals was studied in four base glass compositions derived from the SiO2-Al2O3-Y2O3-SrO-Na2O-K2O/Rb2O/Cs2O-P2O5-F system. The crystal phase formation of these glasses and the main properties of the glass-ceramics, such as thermal and optical properties and radiopacity were compared with a fifth, a reference glass-ceramic. The reference glass-ceramic was characterized as Ca-fluoroapatite glass-ceramic. The four strontium fluoroapatite glass-ceramics showed the following crystal phases: (a) Sr5(PO4)3F - leucite, KAlSi2O6, (b) Sr5(PO4)3F - leucite, KAlSi2O6, and nano-sized NaSrPO4, (c) Sr5(PO4)3F - pollucite, CsAlSi2O6, and nano-sized NaSrPO4, and (d) Sr5(PO4)3F - Rb-leucite, RbAlSi2O6, and nano-sized NaSrPO4. The proof of crystal phase formation was possible by X-ray diffraction. The microstructures, which were studied using scanning electron microscopy, demonstrated a uniform distribution of the crystals in the glass matrix. The Sr-fluoroapatites were precipitated based on an internal crystallization process, and the crystals demonstrated a needle-like morphology. The study of the crystal growth of needle-like Sr-fluoroapatites gave a clear evidence of an Ostwald ripening mechanism. The formation of leucite, pollucite, and Rb-leucite was based on a surface crystallization mechanism. Therefore, a twofold crystallization mechanism was successfully applied to develop these types of glass-ceramics. The main focus of this study was the controlled development of glass-ceramics exhibiting high radiopacity in comparison to the reference glass-ceramic. This goal could be achieved with all four glass-ceramics with the preferred development of the Sr-fluoroapatite - pollucite-type glass-ceramic. In addition to this main development, it was possible to control the thermal properties. Especially the Rb-leucite containing glass-ceramic showed the highest coefficient of thermal expansion (CTE). These

  16. Effects of polyacrylic acid additive on barium sulfate particle morphology

    Energy Technology Data Exchange (ETDEWEB)

    Li, Jie; Liu, Dandan; Jiang, Hongkun; Wang, Jun; Jing, Xiaoyan; Chen, Rongrong [Key Laboratory of Superlight Material and Surface Technology of Ministry of Education, College of Material Science and Chemical Engineering, Harbin Engineering University, Harbin 150001 (China); Zhu, Wenting [Department of Gastroenterology, Harbin Medical University Cancer Hospital, Harbin 150081 (China); Han, Shihui [Key Laboratory of Superlight Material and Surface Technology of Ministry of Education, College of Material Science and Chemical Engineering, Harbin Engineering University, Harbin 150001 (China); Li, Wanyou [College of Power and Energy Engineering, Harbin Engineering University, Harbin 150001 (China); Wei, Hao, E-mail: weihao7512@126.com [Key Laboratory of Superlight Material and Surface Technology of Ministry of Education, College of Material Science and Chemical Engineering, Harbin Engineering University, Harbin 150001 (China); College of Power and Energy Engineering, Harbin Engineering University, Harbin 150001 (China)

    2016-06-01

    In this paper, polyacrylic acid (PAA) was used as a growth modifier to control micron-sized barium sulfate particles via a simple precipitation reaction between sodium sulfate and barium chloride at ambient temperature. The barium sulfate particles were exhibited various morphologies, such as monodisperse spheres, ellipsoids, rose-like aggregates, etc. To better understand the formation mechanisms of the various morphologies of these particles, scanning electron microscopy (SEM), transmission electron microscopy (TEM), X-ray diffraction (XRD) and thermo-gravimetric analysis (TGA) were employed. It was found that the PAA concentration, pH, and Ba{sup 2+} and SO{sub 4}{sup 2−} ions concentrations were the most important parameters controlling the morphology of the BaSO{sub 4} particles. These parameters affected the BaSO{sub 4} morphology by influencing the interactions between the PAA carboxyl groups and inorganic ions and the conformation change of the PAA molecular chains. Moreover, this work attempts to provide a preliminary understanding of the formation of the spherical BaSO{sub 4} particles with the randomly coiled conformation of the polymer. - Highlights: • Polyacrylic acid (PAA) was used as a growth modifier to control micron-sized BaSO{sub 4} particles. • The PAA/BaSO{sub 4} particles were exhibited various morphologies. • Provide a preliminary understanding of the formation mechanism of BaSO{sub 4} particles.

  17. Barium thiolates and selenolates: syntheses and structural principles.

    Science.gov (United States)

    Ruhlandt-Senge, K; Englich, U

    2000-11-17

    The synthesis and structural characterization of a family of barium thiolates and selenolates is described. The thiolates were synthesized by metallation of thiols, the selenolates by reductive insertion of the metal into the selenium-selenium bond of diorganodiselenides. Both reaction sequences were carried out by using barium metal dissolved in ammonia; this afforded barium thiolates and selenolates in good yield and purity. The structural principles displayed in the target compounds span a wide range of solid-state formulations, including monomeric and dimeric species, and separated ion triples, namely [Ba(thf)4(SMes*)2] (1; Mes* = 2,4,6-tBU3C6H2), [Ba(thf)4(SeMes*)2] (2), [Ba([18]crown-6)(hmpa)2][(SeMes*)2] (3), the dimeric [(Ba(py)3(thf)(SeTrip)2)2] (4; py = pyridine, Trip = 2,4.6-iPr3C6H2), and [Ba([18]crown-6)(SeTrip)2] (5). The full range of association modes is completed by [Ba([18]crown-6)(hmpa)SMes*][SMes*] (6) communicated earlier by this group. In the solid state, this compound displays an intermediate ion coordination mode: one anion is bound to the metal, while the second one is unassociated. Together these compounds provide structural information about all three different association modes for alkaline earth metal derivatives. This collection of structural data allows important conclusions about the influence of solvation and ligation on structural trends.

  18. Crystal structure of strontium dinickel iron orthophosphate

    Directory of Open Access Journals (Sweden)

    Said Ouaatta

    2015-10-01

    Full Text Available The title compound, SrNi2Fe(PO43, synthesized by solid-state reaction, crystallizes in an ordered variant of the α-CrPO4 structure. In the asymmetric unit, two O atoms are in general positions, whereas all others atoms are in special positions of the space group Imma: the Sr cation and one P atom occupy the Wyckoff position 4e (mm2, Fe is on 4b (2/m, Ni and the other P atom are on 8g (2, one O atom is on 8h (m and the other on 8i (m. The three-dimensional framework of the crystal structure is built up by [PO4] tetrahedra, [FeO6] octahedra and [Ni2O10] dimers of edge-sharing octahedra, linked through common corners or edges. This structure comprises two types of layers stacked alternately along the [100] direction. The first layer is formed by edge-sharing octahedra ([Ni2O10] dimer linked to [PO4] tetrahedra via common edges while the second layer is built up from a strontium row followed by infinite chains of alternating [PO4] tetrahedra and FeO6 octahedra sharing apices. The layers are held together through vertices of [PO4] tetrahedra and [FeO6] octahedra, leading to the appearance of two types of tunnels parallel to the a- and b-axis directions in which the Sr cations are located. Each Sr cation is surrounded by eight O atoms.

  19. Preparation of nanosized barium zirconate powder by precipitation in aqueous solution

    OpenAIRE

    Boschini, Frédéric; Guillaume, Bernard; Rulmont, André; Cloots, Rudi

    2004-01-01

    Several ways were explored to synthesize barium zirconate by soft chemistry methods in aqueous solution. In the first method the synthesis of barium zirconate was initiated by urea decomposition, through an homogeneous precipitation of barium and zirconium salts followed by a "low temperature" thermal treatment. The kinetic of the reaction and the optimum urea/cation ratio have been determined by means of X-ray diffraction and Inductive Coupled Plasma analyses. It has been demonstrated that a...

  20. Spectroscopy of Ba and Ba$^+$ deposits in solid xenon for barium tagging in nEXO

    OpenAIRE

    Mong, B.; Cook, S; Walton, T.; Chambers, C.; Craycraft, A.; Benitez-Medina, C.; Hall, K.; Fairbank Jr., W.; Albert, J. B.; Auty, D. J.; Barbeau, P. S.; Basque, V.; Beck, D.; Breidenbach, M.; Brunner, T.

    2014-01-01

    Progress on a method of barium tagging for the nEXO double beta decay experiment is reported. Absorption and emission spectra for deposits of barium atoms and ions in solid xenon matrices are presented. Excitation spectra for prominent emission lines, temperature dependence and bleaching of the fluorescence reveal the existence of different matrix sites. A regular series of sharp lines observed in Ba$^+$ deposits is identified with some type of barium hydride molecule. Lower limits for the fl...

  1. Simplified assessment of segmental gastrointestinal transit time with orally small amount of barium

    Energy Technology Data Exchange (ETDEWEB)

    Yuan, Weitang; Zhang, Zhiyong; Liu, Jinbo; Li, Zhen; Song, Junmin; Wu, Changcai [Department of Colorectal Surgery, The First Affiliated Hospital and Institute of Clinical Medicine, Zhengzhou University, 450052 Zhengzhou (China); Wang, Guixian, E-mail: guixianwang@hotmail.com [Department of Colorectal Surgery, The First Affiliated Hospital and Institute of Clinical Medicine, Zhengzhou University, 450052 Zhengzhou (China)

    2012-09-15

    Objective: To determine the effectiveness and advantage of small amount of barium in the measurement of gastrointestinal transmission function in comparison with radio-opaque pallets. Methods: Protocal 1: 8 healthy volunteers (male 6, female 2) with average age 40 ± 6.1 were subjected to the examination of radio-opaque pellets and small amount of barium with the interval of 1 week. Protocol 2: 30 healthy volunteers in group 1 (male 8, female 22) with average age 42.5 ± 8.1 and 50 patients with chronic functional constipation in group 2 (male 11, female 39) with average age 45.7 ± 7.8 were subjected to the small amount of barium examination. The small amount of barium was made by 30 g barium dissolved in 200 ml breakfast. After taking breakfast which contains barium, objectives were followed with abdominal X-ray at 4, 8, 12, 24, 48, 72, 96 h until the barium was evacuated totally. Results: Small amount of barium presented actual chyme or stool transit. The transit time of radio-opaque pallets through the whole gastrointestinal tract was significantly shorter than that of barium (37 ± 8 h vs. 47 ± 10 h, P < 0.05) in healthy people. The transit times of barium in constipation patients were markedly prolonged in colon (61.1 ± 22 vs. 37.3 ± 11, P < 0.01) and rectum (10.8 ± 3.7 vs. 2.3 ± 0.8 h, P < 0.01) compared with unconstipated volunteers. Transit times in individual gastrointestinal segments were also recorded by using small amount of barium, which allowed identifying the subtypes of constipation. Conclusion: The small amount barium examination is a convenient and low cost method to provide the most useful and reliable information on the transmission function of different gastrointestinal segments and able to classify the subtypes of slow transit constipation.

  2. Variation in strontium isotope ratios of archaeological fauna in the Midwestern United States: a preliminary study

    Science.gov (United States)

    Hedman, Kristin M.; Curry, B. Brandon; Johnson, Thomas M.; Fullagar, Paul D.; Emerson, Thomas E.

    2009-01-01

    Strontium isotope values (87Sr/86Sr) in bone and tooth enamel have been used increasingly to identify non-local individuals within prehistoric human populations worldwide. Archaeological research in the Midwestern United States has increasingly highlighted the role of population movement in affecting interregional cultural change. However, the comparatively low level of geologic variation in the Midwestern United States might suggest a corresponding low level of strontium variation, and calls into question the sensitivity of strontium isotopes to identify non-local individuals in this region. Using strontium isotopes of archaeological fauna, we explore the degree of variability in strontium ratios across this region. Our results demonstrate measurable variation in strontium ratios and indicate the potential of strontium analysis for addressing questions of origin and population movement in the Midwestern United States.

  3. The effects of strontium ranelate treatment on ovariectomized Sprague-Dawley rat tibia

    Energy Technology Data Exchange (ETDEWEB)

    Zheng, Y. [Institute of Modern Physics, Fudan University, Shanghai 200433 (China); Jin, W. [Institute of Radiation Medicine, Fudan University, Shanghai 200032 (China); Wang, C.; Yang, M. [Institute of Modern Physics, Fudan University, Shanghai 200433 (China); Shen, H. [Institute of Modern Physics, Fudan University, Shanghai 200433 (China)], E-mail: haoshen@fudan.edu.cn; Eisa, M.H. [Department of Physics, College of Science, Sudan University of Science and Technology, Box 407, Khartoum 111113 (Sudan); Mi, Y. [Institute of Modern Physics, Fudan University, Shanghai 200433 (China)

    2009-06-15

    Micro Proton Induced X-ray Emission (micro-PIXE) technique was used to study the effect of strontium ranelate on osteoporosis resulted from estrogen deficiency. The contents of calcium and strontium in tibia, as well as calcium distribution for structural determination were investigated. Three groups of tibia samples were respectively taken from three groups of female Sprague-Dawley (S.D.) rats, i.e. control, ovariectomized and ovariectomized followed strontium ranelate treatment. It was found that the strontium content was decreasing in the bone from ovariectomized rat compared with that in control, but significantly increasing in the bone from strontium ranelate treated ovariectomized rat. Our study showed that strontium content is a feasible parameter for the diagnosis of osteoporosis caused by estrogen deficiency. Strontium ranelate is an effective antiosteoporosis chemical to rebuild the bone structure and prevent deterioration of bone strength as well.

  4. The effects of strontium ranelate treatment on ovariectomized Sprague-Dawley rat tibia

    Science.gov (United States)

    Zheng, Y.; Jin, W.; Wang, C.; Yang, M.; Shen, H.; Eisa, M. H.; Mi, Y.

    2009-06-01

    Micro Proton Induced X-ray Emission (micro-PIXE) technique was used to study the effect of strontium ranelate on osteoporosis resulted from estrogen deficiency. The contents of calcium and strontium in tibia, as well as calcium distribution for structural determination were investigated. Three groups of tibia samples were respectively taken from three groups of female Sprague-Dawley (S.D.) rats, i.e. control, ovariectomized and ovariectomized followed strontium ranelate treatment. It was found that the strontium content was decreasing in the bone from ovariectomized rat compared with that in control, but significantly increasing in the bone from strontium ranelate treated ovariectomized rat. Our study showed that strontium content is a feasible parameter for the diagnosis of osteoporosis caused by estrogen deficiency. Strontium ranelate is an effective antiosteoporosis chemical to rebuild the bone structure and prevent deterioration of bone strength as well.

  5. Effects of powdered versus liquid barium on the viscosity of fluids used in modified swallow studies

    Energy Technology Data Exchange (ETDEWEB)

    Baron, J.; Alexander, T. [Univ. of Alberta, Dept. of Radiology, Edmonton, Alberta (Canada)

    2003-06-01

    To determine if the viscosity of thickened juice mixtures used in modified barium swallow studies significantly changes with the addition of powdered barium. We also describe a test formulation created using liquid barium, which has a negligible effect on juice viscosity. The viscosities of water and standardized honey- and nectar-consistency juices mixed with different amounts of powdered barium were measured by timing the laminar flow of a given initial hydrostatic head of fluid under gravity though an orifice of fixed diameter. Standardized juices were then mixed with a liquid formulation of barium and with measured quantities of water to produce viscosities that more closely equated with those of the standardized juices. With the addition of powdered barium, viscosity increased in all fluids, most markedly with the nectar-consistency juice. Liquid barium formulations maintained the viscosities of the original thickened juices. Rendering juices radio-opaque with barium powder results in dramatic increases in the viscosity of the resulting mixture and compromises diagnostic accuracy. Liquid barium preparations have the advantage that they can be rapidly and accurately dispensed by syringe, and their use does not significantly increase the viscosity of the preparation. (author)

  6. Sponge-associated bacteria mineralize arsenic and barium on intracellular vesicles

    Science.gov (United States)

    Keren, Ray; Mayzel, Boaz; Lavy, Adi; Polishchuk, Iryna; Levy, Davide; Fakra, Sirine C.; Pokroy, Boaz; Ilan, Micha

    2017-01-01

    Arsenic and barium are ubiquitous environmental toxins that accumulate in higher trophic-level organisms. Whereas metazoans have detoxifying organs to cope with toxic metals, sponges lack organs but harbour a symbiotic microbiome performing various functions. Here we examine the potential roles of microorganisms in arsenic and barium cycles in the sponge Theonella swinhoei, known to accumulate high levels of these metals. We show that a single sponge symbiotic bacterium, Entotheonella sp., constitutes the arsenic- and barium-accumulating entity within the host. These bacteria mineralize both arsenic and barium on intracellular vesicles. Our results indicate that Entotheonella sp. may act as a detoxifying organ for its host. PMID:28233852

  7. X-Band Microwave Reflection Properties of Samarium/Bismuth-Substituted Barium Lanthanum Titanate Ceramics

    Science.gov (United States)

    Bahel, Shalini; Pubby, Kunal; Narang, Sukhleen Bindra

    2017-01-01

    Samarium/bismuth-substituted barium lanthanum titanate ceramics with chemical composition Ba4 (La_{1 - y - z} Smy Biz )_{9.33} Ti_{18} O_{54} (y = 0.5, 0.7; z = 0.05, 0.10, 0.15), intended as microwave reflecting materials, have been investigated in microwave X-band (8.2 GHz to 12.4 GHz) and the effect of substitution on their dielectric properties, i.e., dielectric constant and dielectric loss tangent, has been studied by vector network analyzer. Dielectric analysis showed that the dielectric constant increased with increasing samarium as well as bismuth content. Dielectric relaxation was observed for all samples in the scanned frequency range. Microwave reflection and transmission analysis of ceramic pellets of thickness 4 mm was carried out using two methods, i.e., open- and short-circuit approach, both indicating very high values of reflected power and very low values of transmitted power for all the doped materials in comparison with the base composition. The doped compositions are therefore potential microwave shielding materials for use in anechoic chambers, microwave laboratories, and radar equipment. Double-layer reflectors are also proposed, having better reflection properties (˜99% reflection) compared with single-layer reflectors.

  8. X-Band Microwave Reflection Properties of Samarium/Bismuth-Substituted Barium Lanthanum Titanate Ceramics

    Science.gov (United States)

    Bahel, Shalini; Pubby, Kunal; Narang, Sukhleen Bindra

    2017-03-01

    Samarium/bismuth-substituted barium lanthanum titanate ceramics with chemical composition Ba4 (La_{1 - y - z} Smy Biz )_{9.33} Ti_{18} O_{54} ( y = 0.5, 0.7; z = 0.05, 0.10, 0.15), intended as microwave reflecting materials, have been investigated in microwave X-band (8.2 GHz to 12.4 GHz) and the effect of substitution on their dielectric properties, i.e., dielectric constant and dielectric loss tangent, has been studied by vector network analyzer. Dielectric analysis showed that the dielectric constant increased with increasing samarium as well as bismuth content. Dielectric relaxation was observed for all samples in the scanned frequency range. Microwave reflection and transmission analysis of ceramic pellets of thickness 4 mm was carried out using two methods, i.e., open- and short-circuit approach, both indicating very high values of reflected power and very low values of transmitted power for all the doped materials in comparison with the base composition. The doped compositions are therefore potential microwave shielding materials for use in anechoic chambers, microwave laboratories, and radar equipment. Double-layer reflectors are also proposed, having better reflection properties (˜99% reflection) compared with single-layer reflectors.

  9. 铝酸钡与氢氧化钡脱硫过程比较%Comparison of Barium Aluminate and Barium Hydroxide Desulfurization Process

    Institute of Scientific and Technical Information of China (English)

    张念炳; 黎志英; 丁彤

    2012-01-01

    The seed precipitation liquor was desulfurized with barium aluminate and barium hydroxide respectively. The desulfurization slag was characterized by XRD analysis, and the desulfurization process was compared. The results show that barium hydroxide exceeds barium aluminate with better desulfurization in terms of effect, speed and duration. In the desulfurization process with barium aluminate, 2BaO · Al2O3 · 5H2O is firstly produced in the reaction of barium aluminate with alkali, and then it reacts with sodium sulfate and sodium carbonate. To compare, Ba(OH)2 · 8H2O directly reacts with sodium sulfate and sodium carbonate in the desulfurization process with barium hydroxide. Both of desulfurization reaction processes can be described with "shrinking core model".%用铝酸钡和氢氧化钡对种分母液进行脱硫试验,对脱硫渣进行XRD分析,并比较脱硫过程.结果表明,氢氧化钡的脱硫效果更好,脱硫完成时间更短,速率更快;铝酸钡先与碱液反应生成2BaO·Al2O3·5H2O,再与硫碱和碳碱反应,而氢氧化钡直接与硫碱和碳碱反应,脱硫过程均可用未反应核模型描述.

  10. Membrane-based separation technologies for cesium, strontium, and technetium

    Energy Technology Data Exchange (ETDEWEB)

    Kafka, T.

    1996-10-01

    This work is one of two parallel projects that are part of an ESP task to develop high-capacity, selective, solid extractants for cesium, strontium, and technetium from nuclear wastes. In this subtask, Pacific Northwest National Laboratory (PNNL) is collaborating with 3M, St. Paul, Minnesota, working in cooperation with IBC Advanced Technologies, American Fork, Utah.

  11. Strontium hydrogeochemistry of thermal groundwaters from Baikal and Xinzhou

    Institute of Scientific and Technical Information of China (English)

    王焰新; 沈照理

    2001-01-01

    This paper reports our work on the strontium hydrogeochemistry of thermal groundwa-ters in the Baikal Rift System (BRS) in Russia and Mongolia and the Xinzhou basin of the Shanxi Rift System (SRS) in northern China. Though similar in geological background, groundwaters from the BRS and the Xinzhou basin have different strontium isotope compositions. Both the strontium contents and the 87Sr/86Sr ratios of thermal water samples from Xinzhou are higher than those of most samples from Baikal. The major reason is the difference in hostrock geochemistry. The hos-trocks of the Xinzhou waters are Archaean metamorphic rocks, while those of the Baikal waters except the Kejielikov spring are Proterozoic or younger rocks. In the study areas, cold groundwaters usually show lower 87Sr/86Sr ratio due to shorter water-rock interaction history and lower equilibration degree. Strontium hydrogeochemistry often provides important information about mixing processes. Ca/Sr ratio can be used as an important hydrogeochemical pa

  12. Laser-induced collisional autoionization in europium and strontium atoms.

    Science.gov (United States)

    Buffa, R

    1995-01-15

    An experiment that involves laser-induced collisional autoionization in europium and strontium atoms is proposed and the spectral line shape of the cross section is calculated on the basis of data available in the literature. The feasibility of the experiment both in oven cells and in a crossed-atomic-beam geometry is discussed.

  13. Laser sources for precision spectroscopy on atomic strontium.

    Science.gov (United States)

    Poli, N; Ferrari, G; Prevedelli, M; Sorrentino, F; Drullinger, R E; Tino, G M

    2006-04-01

    We present a new laser setup designed for high-precision spectroscopy on laser cooled atomic strontium. The system, which is entirely based on semiconductor laser sources, delivers 200 mW at 461 nm for cooling and trapping atomic strontium from a thermal source, 4 mW at 497 nm for optical pumping from the metastable P23 state, 12 mW at 689 nm on linewidth less than 1 kHz for second-stage cooling of the atomic sample down to the recoil limit, 1.2 W at 922 nm for optical trapping close to the "magic wavelength" for the 0-1 intercombination line at 689 nm. The 689 nm laser was already employed to perform a frequency measurement of the 0-1 intercombination line with a relative accuracy of 2.3 x 10(-11), and the ensemble of laser sources allowed the loading in a conservative dipole trap of multi-isotopes strontium mixtures. The simple and compact setup developed represents one of the first steps towards the realization of a transportable optical standards referenced to atomic strontium.

  14. Thermal behaviour of strontium tartrate single crystals grown in gel

    Indian Academy of Sciences (India)

    M H Rahimkutty; K Rajendra Babu; K Sreedharan Pillai; M R Sudarsana Kumar; C M K Nair

    2001-04-01

    Thermal behaviour of strontium tartrate crystals grown with the aid of sodium metasilicate gel is investigated using thermogravimetry (TG) and differential thermal analysis (DTA). Effect of magnetic field and dopant (Pb)2+ on the crystal stability is also studied using thermal analysis. This study reveals that water molecules are locked up in the lattice with different strengths in the grown crystals.

  15. Vibrational spectra of the two hydrates of strontium oxalate.

    Science.gov (United States)

    D'Antonio, Maria C; Torres, María M; Palacios, Daniel; González-Baró, Ana C; Baran, Enrique J

    2015-02-25

    The infrared and Raman spectra of the two hydrates of strontium oxalate, SrC2O4⋅H2O and SrC2O4⋅2H2O, were recorded and discussed on the basis of their structural peculiarities and in comparison with the spectra of the related calcium oxalates and other previously investigated metallic oxalates.

  16. Strontium adsorption and penetration in kaolinite at low Sr

    NARCIS (Netherlands)

    Ning, Zigong; Ishiguro, Munehide; Koopal, Luuk K.; Sato, Tsutomu; Kashiwagi, Junichi

    2017-01-01

    Behavior of radioactive strontium (Sr2+) in contaminated soils is an important issue in relation to nuclear power plant accidents. The Sr2+ adsorption on kaolinite and its migration in a kaolinite soil were investigated because toxic effects of radioactive Sr2+ have been found to be very severe for

  17. Electrical behaviour of strontium-doped lanthanum manganite interfaces

    DEFF Research Database (Denmark)

    Koch, Søren; Hendriksen, P.V.; Jacobsen, Torben

    2005-01-01

    The contact resistance of strontium-doped lanthanum manganite (LSM) contact pairs is investigated by polarisation analysis at different temperatures and atmospheres. The ceramic contacts have a high contact resistance, and strongly nonlinear current–voltage behaviour is observed at low temperatures...

  18. Variation of Fundamental Constants

    Science.gov (United States)

    Flambaum, V. V.

    2006-11-01

    Theories unifying gravity with other interactions suggest temporal and spatial variation of the fundamental ``constants'' in expanding Universe. The spatial variation can explain a fine tuning of the fundamental constants which allows humans (and any life) to appear. We appeared in the area of the Universe where the values of the fundamental constants are consistent with our existence. We present a review of recent works devoted to the variation of the fine structure constant α, strong interaction and fundamental masses. There are some hints for the variation in quasar absorption spectra. Big Bang nucleosynthesis, and Oklo natural nuclear reactor data. A very promising method to search for the variation of the fundamental constants consists in comparison of different atomic clocks. Huge enhancement of the variation effects happens in transition between accidentally degenerate atomic and molecular energy levels. A new idea is to build a ``nuclear'' clock based on the ultraviolet transition between very low excited state and ground state in Thorium nucleus. This may allow to improve sensitivity to the variation up to 10 orders of magnitude! Huge enhancement of the variation effects is also possible in cold atomic and molecular collisions near Feshbach resonance.

  19. Separation of lanthanum, hafnium, barium and radiotracers yttrium-88 and barium-133 using crystalline zirconium phosphate and phosphonate compounds as prospective materials for a Ra-223 radioisotope generator

    Energy Technology Data Exchange (ETDEWEB)

    Moeller, Teresia [Lynntech Inc., 7610 Eastmark Dr, College Station, TX 77840 (United States); Bestaoui, Naima, E-mail: Naima.Bestaoui@Lynntech.co [Lynntech Inc., 7610 Eastmark Dr, College Station, TX 77840 (United States); Wierzbicki, Melissa; Adams, Todd; Clearfield, Abraham [Lynntech Inc., 7610 Eastmark Dr, College Station, TX 77840 (United States)

    2011-07-15

    Crystalline hybrid organic/inorganic ion exchangers based on zirconium phosphate and phosphonate compounds were evaluated for application in radium-223 generator for radiopharmaceutical applications. Various compositions were synthesized and the selectivity of these materials was determined for inactive lanthanum, hafnium and barium, and radiotracers yttrium-88 and barium-133. The hybrid materials show very efficient lanthanum/barium separation; the response for zirconium phosphate was even better. A small-scale column loaded with pelletized zirconium phosphate compound demonstrated excellent retention of {sup 88}Y and release of {sup 133}Ba.

  20. Effect of temperature on polarization reversal of strontium-doped lead zirconate titanate (PSZT) ceramics

    Indian Academy of Sciences (India)

    N Nwathore; C M Lonkar; D K Kharat

    2011-02-01

    The effect of temperature on polarization reversal of strontium-doped lead zirconate titanate ceramics was studied. The piezoelectric properties viz. dielectric constant and piezoelectric coupling coefficient, were used for polarization reversal characteristic. These properties and apparent coercive field weremeasured during polarization reversal at different temperatures. Results indicated that at higher temperature apparent coercive field decreased. Polarization reversal and further polarization reversal was quite asymmetric. After polarization reversal, dielectric constant was found to increase at all temperatures while piezoelectric coupling coefficient increased above the temperature of polarization. The trend shown by dielectric constant indicates that at 25°C, 1.5 kV/mm field can be applied safely to this material without much compromising the properties. D.c. field of 3.0 kV/mm and 100°C temperature can be predicted as poling parameters from their effect on kp. Apparent coercive field has shown non-linear relationship with temperature. It was of exponential decay type.

  1. Elastic constants of calcite

    Science.gov (United States)

    Peselnick, L.; Robie, R.A.

    1962-01-01

    The recent measurements of the elastic constants of calcite by Reddy and Subrahmanyam (1960) disagree with the values obtained independently by Voigt (1910) and Bhimasenachar (1945). The present authors, using an ultrasonic pulse technique at 3 Mc and 25??C, determined the elastic constants of calcite using the exact equations governing the wave velocities in the single crystal. The results are C11=13.7, C33=8.11, C44=3.50, C12=4.82, C13=5.68, and C14=-2.00, in units of 1011 dyncm2. Independent checks of several of the elastic constants were made employing other directions and polarizations of the wave velocities. With the exception of C13, these values substantially agree with the data of Voigt and Bhimasenachar. ?? 1962 The American Institute of Physics.

  2. Algorithm for structure constants

    CERN Document Server

    Paiva, F M

    2011-01-01

    In a $n$-dimensional Lie algebra, random numerical values are assigned by computer to $n(n-1)$ especially selected structure constants. An algorithm is then created, which calculates without ambiguity the remaining constants, obeying the Jacobi conditions. Differently from others, this algorithm is suitable even for poor personal computer. ------------- En $n$-dimensia algebro de Lie, hazardaj numeraj valoroj estas asignitaj per komputilo al $n(n-1)$ speciale elektitaj konstantoj de strukturo. Tiam algoritmo estas kreita, kalkulante senambigue la ceterajn konstantojn, obeante kondicxojn de Jacobi. Malsimile al aliaj algoritmoj, tiu cxi tauxgas ecx por malpotenca komputilo.

  3. Radiographic constant exposure technique

    DEFF Research Database (Denmark)

    Domanus, Joseph Czeslaw

    1985-01-01

    The constant exposure technique has been applied to assess various industrial radiographic systems. Different X-ray films and radiographic papers of two producers were compared. Special attention was given to fast film and paper used with fluorometallic screens. Radiographic image quality...... was tested by the use of ISO wire IQI's and ASTM penetrameters used on Al and Fe test plates. Relative speed and reduction of kilovoltage obtained with the constant exposure technique were calculated. The advantages of fast radiographic systems are pointed out...

  4. The aliquot constant

    CERN Document Server

    Bosma, Wieb

    2009-01-01

    The average value of log s(n)/n taken over the first N even integers is shown to converge to a constant lambda when N tends to infinity; moreover, the value of this constant is approximated and proven to be less than 0. Here s(n) sums the divisors of n less than n. Thus the geometric mean of s(n)/n, the growth factor of the function s, in the long run tends to be less than 1. This could be interpreted as probabilistic evidence that aliquot sequences tend to remain bounded.

  5. Microwave-assisted fabrication of strontium doped apatite coating on Ti6Al4V

    Energy Technology Data Exchange (ETDEWEB)

    Zhou, Huan, E-mail: huanzhou@cczu.edu.cn [Institute of Biomedical Engineering and Health Sciences, Changzhou University, Changzhou, Jiangsu 213164 (China); Kong, Shiqin [Institute of Biomedical Engineering and Health Sciences, Changzhou University, Changzhou, Jiangsu 213164 (China); School of Materials Science and Engineering, Changzhou University, Changzhou, Jiangsu 213164 (China); Pan, Yan; Zhang, Zhiguo [Institute of Biomedical Engineering and Health Sciences, Changzhou University, Changzhou, Jiangsu 213164 (China); Deng, Linhong, E-mail: dlh@cczu.edu.cn [Institute of Biomedical Engineering and Health Sciences, Changzhou University, Changzhou, Jiangsu 213164 (China)

    2015-11-01

    Strontium has been shown to be a beneficial dopant to calcium phosphates when incorporated at nontoxic level. In the present work we studied the possibility of solution derived doping strontium into calcium phosphate coatings on titanium alloy Ti6Al4V based implants by a recently reported microwave-assisted method. By using this method strontium doped calcium phosphate nuclei were deposited to pretreated titanium alloy surface dot by dot to compose a crack-free coating layer. The presence of strontium in solution led to reduced roughness of the coating and finer nucleus size formed. In vitro study found that proliferation and differentiation of osteoblast cells seeded on the coating were influenced by strontium content in coatings, showing an increasing followed by a decreasing behavior with increasing substitution of calcium by strontium. It is suggested that this new microwave-assisted strontium doped calcium phosphate coatings may have great potential in implant modification. - Highlights: • Strontium doped calcium phosphate coating is deposited with microwave irradiation. • Increase of strontium reduces coating roughness and results in finer nucleus size. • Proliferation and differentiation of osteoblasts depend on doped strontium content.

  6. Physico-chemical and in vitro biological evaluation of strontium/calcium silicophosphate glass.

    Science.gov (United States)

    Hesaraki, Saeed; Alizadeh, Masoud; Nazarian, Hamid; Sharifi, Davood

    2010-02-01

    Strontium is known to reduce bone resorption and stimulate bone formation. Incorporation of strontium into calcium phosphate bioceramics has been widely reported. In this work, calcium and calcium/strontium silicophosphate glasses were synthesized from the sol-gel process and their rheological, thermal, and in vitro biological properties were studied and compared to each other. The results showed that the gel viscosity and thus the rate of gel formation increased by using strontium in glass composition and by increasing aging temperature. In strontium-containing glass, the crystallization temperature increased and the type of the crystallized phase was different to that of strontium-free glass. Both glasses favored precipitation of calcium phosphate layer when they were soaked in simulated body fluid; however strontium seemed to retard the rate of precipitation slightly. The in vitro biodegradation rate of the strontium/calcium silicophosphate glass was higher than that of strontium-free one. The cell culture experiments carried out using rat calvaria osteoblasts showed that the incorporation of strontium into the glass composition stimulated proliferation of the cells and enhanced their alkaline phosphatase activity, depending on cell culture period.

  7. Compassion is a constant.

    Science.gov (United States)

    Scott, Tricia

    2015-11-01

    Compassion is a powerful word that describes an intense feeling of commiseration and a desire to help those struck by misfortune. Most people know intuitively how and when to offer compassion to relieve another person's suffering. In health care, compassion is a constant; it cannot be rationed because emergency nurses have limited time or resources to manage increasing demands.

  8. Barium Swallow Findings in the Evaluation of Patients with Dysphagia

    Directory of Open Access Journals (Sweden)

    Amirhosein Hashemi Attar

    2011-05-01

    Full Text Available Background/Objective: Dysphagia is a subjective"nsensation of difficulty in swallowing that has a wide"nrange of etiologies from psychosomatic disorders"nto high grade neoplasms. In this study we evaluated"nbarium swallow findings of patients with dysphagia."nPatients and Methods: We evaluated 200 patients"n(117 men, 83 women; mean age, 49.6 years with"ncomplaint of dysphagia. Fluoroscopic barium"nswallow was done for all the patients and they were"nreviewed for primary peristalsis (presence or absence,"nAbstracts"nS62 Iran J Radiol 2011, 8 (Supp.1"nAbstracts"nimpaired lower esophageal sphincter, esophageal dilatation, delayed emptying of barium, nonperistaltic contractions, stricture and filling defects. Clinical and in some cases endoscopic or manometric follow up was done for all patients."nResults: We had 134 (67% normal barium swallow"nexams with uncomplicated clinical courses. Sixty"nsix patients (33% had abnormal imaging findings"nincluding stricture in 24 patients (12%, filling defect"nin 12 patients (6% and mucosal abnormality in 14"n(7% patients (six cases of mucosal irregularity, three"ncases of mucosal ulceration and five cases of mucosal"nherniation, Bird's beak sign in three patients (1.5%,"ntertiary spasm in six patients (3% and hiatal hernia in"nseven patients (3.5%."nConclusion: In the majority of patients with dysphagia,"nbarium swallow is the only paraclinical study needed"nto plan proper treatment. If radiographic findings are"nequivocal, endoscopy or manometry may be required"nfor more certain diagnosis.

  9. Novel Pharmaceutical Strontium Malonate Influence on Calcium and Strontium Adsorption by Dog Femur and by Dog Teeth in a Four-Week Toxicity Study

    DEFF Research Database (Denmark)

    Raffalt, Anders Christer; Christgau, Stephan; Andersen, Jens Enevold Thaulov

    Strontium is known to have a positive effect on bone by concomitantly increasing bone formation while decreasing bone resorption thereby providing a sustained skeletal benefit. Strontium malonate is being developed as a novel orally available pharmaceutical for the treatment and prevention of ost...

  10. Novel Pharmaceutical Strontium Malonate Influence on Calcium and Strontium Adsorption by Dog Femur and by Dog Teeth in a Four-Week Toxicity Study

    DEFF Research Database (Denmark)

    Raffalt, Anders Christer; Christgau, Stephan; Andersen, Jens Enevold Thaulov

    Strontium is known to have a positive effect on bone by concomitantly increasing bone formation while decreasing bone resorption thereby providing a sustained skeletal benefit. Strontium malonate is being developed as a novel orally available pharmaceutical for the treatment and prevention...

  11. Investigation on the effects of milling atmosphere on synthesis of barium ferrite/magnetite nanocomposite

    NARCIS (Netherlands)

    Molaei, M.J.; Ataie, A.; Raygan, S.; Picken,n S.J.

    2011-01-01

    In this research, barium ferrite /magnetite nanocomposites synthesized via a mechano-chemical route. Graphite was used in order to reduce hematite content of barium ferrite to magnetite to produce a magnetic nanocomposite. The effects of processing conditions on the powder characteristics were inves

  12. Complete sulphate removal from neutralised acidic mine drainage with barium carbonate

    CSIR Research Space (South Africa)

    Swanepoel, H

    2012-03-01

    Full Text Available -barium-calcium) Desalination process which uses barium salts to further reduce the sulphate concentration to acceptable levels with the added advantage that sulphate removal can be controlled due to the low solubility of BaSO4. This paper reports on the results...

  13. New efficient catalyst for ammonia synthesis: barium-promoted cobalt on carbon

    DEFF Research Database (Denmark)

    Hagen, Stefan; Barfod, Rasmus; Fehrmann, Rasmus

    2002-01-01

    Barium-promoted cobalt catalysts supported on carbon exhibit higher ammonia activities at synthesis temperatures than the commercial, multipromoted iron catalyst and also a lower ammonia......Barium-promoted cobalt catalysts supported on carbon exhibit higher ammonia activities at synthesis temperatures than the commercial, multipromoted iron catalyst and also a lower ammonia...

  14. Control on Crystal Forms of Ultrafine Barium Carbonate Particles and Study on its Mechanism

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    Barium carbonate particles were prepared by using homogeneous precipitation method and co-precipitation method respectively. Through adding different crystalline controlling modifiers, Barium carbonate particles in five different shapes including linear, needle-like, pillarlike, sphere-like and dumbbell-like were synthesized. These particles were characterized by SEM and XRD, and their synthetic mechanism was discussed in this paper.

  15. Spectroscopic properties of trivalent praseodymium in barium yttrium fluoride

    Energy Technology Data Exchange (ETDEWEB)

    Di Bartolo, B. E-mail: dibartob@bc.edurinodiba@attbi.com; Bowlby, B.E

    2003-05-01

    We have conducted a spectroscopic investigation of Pr{sup 3+} in barium yttrium fluoride (BaY{sub 2}O{sub 8}). Two doping concentrations were used: BaY{sub 2}F{sub 8}:Pr{sup 3+} (0.3%) and BaY{sub 2}F{sub 8}:Pr{sup 3+} (1%). The measurements included absorption, luminescence under continuous and pulsed excitations, and thermal effects on some sharp lines. The experimental results were used to characterize this system.

  16. A barium-rich binary central star in Abell 70

    CERN Document Server

    Boffin, Henri M J; Frew, D J; Acker, A; Köppen, J; Moffat, A F J; Parker, Q A

    2011-01-01

    We have found the central star of Abell 70 (PN G038.1-25.4, hereafter A 70) to be a binary consisting of a G8 IV-V secondary and a hot white dwarf. The secondary shows enhanced Ba II and Sr II features, firmly classifying it as a barium star. The nebula is found to have Type-I chemical abundances with helium and nitrogen enrichment, which combined with future abundance studies of the central star, will establish A 70 as a unique laboratory for studying s-process AGB nucleosynthesis.

  17. Dissolved strontium and calcium levels in the tropical Indian Ocean

    Science.gov (United States)

    Steiner, Zvi; Sarkar, Amit; Turchyn, Alexandra

    2017-04-01

    Measurements of seawater alkalinity and dissolved calcium concentrations along oceanic transects are often used to calculate calcium carbonate precipitation and dissolution rates. Given that the distribution coefficient of strontium in CaCO3 varies greatly between different groups of organisms, adding precise measurements of dissolved strontium concentrations provides opportunities to also track relative contributions of these different groups to the regional CaCO3 cycle. However, there are several obstacles to this approach. These obstacles include unresolved systematic discrepancies between seawater calcium and alkalinity data, very large analytical noise around the calcium concentration measurements and the unconstrained role of acantharia (radiolarian precipitating SrSO4 skeletons) in the marine strontium cycle. During the first cruise of the second International Indian Ocean Expedition (IIOE-2) water samples were collected along 67°E from 9°N to 5°S to explore the dissolution rate of calcium carbonate in the water. The dissolution rate can be calculated by combining measurements of water column potential alkalinity with calcium and strontium concentrations measured by ICP-OES and calcium concentration measurements using isotope dilution thermal ionization mass spectrometry (ID-TIMS). CaCO3 mineral saturation state calculated using pH and total alkalinity suggests that along 67°E, the aragonite saturation horizon lays at depth of 500 m on both sides of the equator. Across the cruise transect, dissolved strontium concentrations increase by 2-3% along the thermocline suggesting rapid recycling of strontium rich phases. This is particularly evident just below the thermocline at 8-9°N and below 1000 m water depth, south of the equator. The deep, southern enrichment in strontium does not involve a change in the Sr/Ca ratio, suggesting that this strontium enrichment is related to CaCO3 dissolution. In contrast, in the intermediate waters of the northern part of

  18. Determination of strontium and simultaneous determination of strontium oxide, magnesium oxide and calcium oxide content of Portland cement by derivative ratio spectrophotometry.

    Science.gov (United States)

    Idriss, K A; Sedaira, H; Ahmed, S S

    2009-04-15

    A derivative spectrophotometric method has been developed for the determination of strontium in Portland cement. The method is applied successfully for the simultaneous determination of SrO, MgO and CaO. It is based on the use of Alizarin Complexone (AC) as a complexing agent and measurement of the derivative ratio spectra of the analytes. Interferences of manganese(II) and zinc(II) were eliminated by precipitation. The validity of the method was examined by analyzing several Standard Reference Material (SRM) Portland cement samples. The strontium complex formed at pH 9.5 allows precise and accurate determination of strontium over the concentration range of 1.5-18 mg L(-1) of strontium. The MDL (at 95% confidence level) was found to be 25 ng mL(-1) for strontium in National Institute of Standards and Technology (NIST) cement samples using the proposed method.

  19. Preparation of nanosized barium zirconate powder by thermal decomposition of urea in an aqueous solution containing barium and zirconium, and by calcination of the precipitate

    OpenAIRE

    Boschini, Frédéric; Robertz, B.; Rulmont, André; Cloots, Rudi

    2003-01-01

    The synthesis of barium zirconate was initiated by urea induced homogeneous precipitation followed by a "low temperature" thermal treatment. The kinetic of the reaction and the optimum urea/cation ratio have been determined by means of X-ray diffraction and Inductive Coupled Plasma analyses. It has been demonstrated that an amorphous zirconium hydrated oxide starts to precipitate followed by the precipitation of barium carbonate. A calcination at 1200 degreesC during 2 h gives rise to the for...

  20. Barium Tagging in Liquid Xenon for the nEXO Experiment

    Science.gov (United States)

    Kravitz, Scott; nEXO Collaboration

    2016-09-01

    nEXO is a next-generation experiment designed to search for neutrinoless double beta decay of xenon-136 in a liquid xenon time projection chamber. Positive observation of this decay would determine the neutrino to be a MAJORANA particle, as well as measure the absolute neutrino mass scale. In order to greatly reduce background contributions to this search, the collaboration is developing several ``barium tagging'' techniques to recover and identify the decay daughter, barium-136. Barium tagging may be available for a second phase of nEXO operation, allowing for neutrino mass sensitivity beyond the inverted mass hierarchy. Tagging methods for this phase include barium-ion capture on a probe with identification by resonance ionization laser spectroscopy. Inclusion of an argon ion gun in this system allows for improved cleaning and preparation of the barium deposition substrate, with recent results reported in this presentation.

  1. Electrical characterization of doped strontium titanate thin films for semiconductor memories

    Science.gov (United States)

    Han, Jeong Hee

    2002-08-01

    Doped strontium titanate (ST) thin films were investigated for high-density memory applications. ST has become a promising candidate to replace conventional silicon oxide due to its high inherent dielectric constant, superior leakage characteristics, and good chemical stability. However, oxygen vacancies and the problems that arise as a result are one of the main drawbacks against this material. Resistance degradation is a serious reliability issue in perovskite titanate films and may be a result of oxygen vacancies. In this dissertation, an attempt to reduce the resistance degradation was made by doping the ST films with both niobium and lanthanum. Niobium is a B-site donor in the perovskite, whereas lanthanum is an A-site donor. Both have an extra valence charge than the atom which it replaces in the crystal structure. With a higher valence charge, the number of oxygen vacancies is hoped to be reduced and result in better electrical performance. Experimental results showed that the degradation rate is reduced by doping with either niobium or lanthanum. A bi-layer study was also performed to optimize the dielectric with the strengths of both doped and undoped strontium titanate and to distinguish the source of the oxygen vacancies. A study on the conduction mechanisms and dielectric dispersion was also performed. An additional study was made on the effect of iridium as a possible gate electrode for a MOS capacitor. Hafnium oxide was used as the high-permittivity oxide. The results observed showed that the capacitance was higher for iridium electrodes than those for platinum electrodes. However, both electrodes showed unacceptable frequency dispersion which may be caused by crude patterning techniques. A hysteresis review was also done for hafnium and zirconium oxides. It was observed that the hysteresis measured in the high-permittivity oxides are dependent on the accumulation sweep voltage due to the trapping and de-trapping of charge at the dielectric

  2. Application of spin flash dryer in barium carbonate drying%旋转闪蒸干燥器在碳酸钡干燥中的应用

    Institute of Scientific and Technical Information of China (English)

    张小钦; 张风缺

    2009-01-01

    介绍了河北诺达化工设备有限公司开发生产的旋转闪蒸干燥器代替回转圆筒干燥器在碳酸钡干燥过程中的应用.通过对投资、能耗、产品质量、环保效益的详细分析得出结论:用旋转闪蒸干燥器代替回转圆筒干燥器,具有节省投资,节约能耗,提高产品质量,减小环境污染等优势,为碳酸钡的干燥提供了一种新方法.该设备也适用于碳酸锶、硫酸钡、碳酸钙等滤饼类物料的干燥,同样对于冶金、化工、医药、食品等行业的滤饼类物料的干燥也具有极高的应用价值.%Application of spin flash dryer developed and produced by Hebei Nuoda Chemical Equipment Co.,Ltd.to replace rotary cylinder dryer in drying process of barium carbonate was introduced.Through detailed analysis on investment,energy consumption,product quality,and environmental benefits,the conclusion was obtained:comparing with rotary cylinder dryer,spin flash dryer has the advantages,such as less investment,energy saving,better product quality,and smaller pollution,which provide a new drying way for barium carbonate production.Meanwhile,this equipment is suitable for drying other cake - type materials,such as strontium carbonate,barium sulfate,and calcium carbonate.It also has high application value for cake - type materials in other industries,such as metallurgical,chemical,pharmaceutical,and food.

  3. Strontium isotope geochemistry of soil and playa deposits near Yucca Mountain, Nevada

    Energy Technology Data Exchange (ETDEWEB)

    Marshall, B.D.; Mahan, S.A. [Geological Survey, Denver, CO (United States)

    1994-12-31

    The isotopic composition of strontium contained in the carbonate fractions of soils provides an excellent tracer which can be used to test models for their origin. This paper reports data on surface coatings and cements, eolian sediments, playas and alluvial fan soils which help to constrain a model for formation of the extensive calcretes and fault infillings in the Yucca Mountain region. The playas contain carbonate with a wide range of strontium compositions; further work will be required to fully understand their possible contributions to the pedogenic carbonate system. Soils from an alluvial fan to the west of Yucca Mountain show that only small amounts of strontium are derived from a fan draining a carbonate terrane have strontium component. Although much evidence points to an eolian source for at least some of the strontium in the pedogenic carbonates near Yucca Mountain, an additional component or past variation of strontium composition in the eolian source is required to model the pedogenic carbonate system.

  4. Tungsten and Barium Transport in the Internal Plasma of Hollow Cathodes

    Science.gov (United States)

    Polk, James E.; Mikellides, Ioannis G.; Katz, Ira; Capece, Angela M.

    2008-01-01

    The effect of tungsten erosion, transport and redeposition on the operation of dispenser hollow cathodes was investigated in detailed examinations of the discharge cathode inserts from an 8200 hour and a 30,352 hour ion engine wear test. Erosion and subsequent re-deposition of tungsten in the electron emission zone at the downstream end of the insert reduces the porosity of the tungsten matrix, preventing the flow of barium from the interior. This inhibits the interfacial reactions of the barium-calcium-aluminate impregnant with the tungsten in the pores. A numerical model of barium transport in the internal xenon discharge plasma shows that the barium required to reduce the work function in the emission zone can be supplied from upstream through the gas phase. Barium that flows out of the pores of the tungsten insert is rapidly ionized in the xenon discharge and pushedback to the emitter surface by the electric field and drag from the xenon ion flow. Thisbarium ion flux is sufficient to maintain a barium surface coverage at the downstream endgreater than 0.6, even if local barium production at that point is inhibited by tungsten deposits. The model also shows that the neutral barium pressure exceeds the equilibrium vapor pressure of the impregnant decomposition reaction over much of the insert length,so the reactions are suppressed. Only a small region upstream of the zone blocked by tungsten deposits is active and supplies the required barium. These results indicate that hollowcathode failure models based on barium depletion rates in vacuum dispenser cathodes are very conservative.

  5. Enhanced effects of variation of the fundamental constants in laser interferometers and application to dark matter detection

    CERN Document Server

    Stadnik, Y V

    2015-01-01

    We outline new laser interferometer measurements to search for variation of the electromagnetic fine-structure constant $\\alpha$ and particle masses (including a non-zero photon mass). We propose a strontium optical lattice clock -- silicon single-crystal cavity interferometer as a novel small-scale platform for these new measurements. Multiple passages of a light beam inside an interferometer enhance the effects due to variation of the fundamental constants by the mean number of passages ($N_{\\textrm{eff}} \\sim 10^2$ for a large-scale gravitational-wave detector, such as LIGO, Virgo, GEO600 or TAMA300, while $N_{\\textrm{eff}} \\sim 10^5$ for a strontium clock -- silicon cavity interferometer). Our proposed laser interferometer measurements may be implemented as an extremely precise tool in the direct detection of scalar dark matter that forms an oscillating classical field or topological defects.

  6. Variation of fundamental constants

    CERN Document Server

    Flambaum, V V

    2006-01-01

    We present a review of recent works devoted to the variation of the fine structure constant alpha, strong interaction and fundamental masses. There are some hints for the variation in quasar absorption spectra, Big Bang nucleosynthesis, and Oklo natural nuclear reactor data. A very promising method to search for the variation of the fundamental constants consists in comparison of different atomic clocks. Huge enhancement of the variation effects happens in transition between accidentally degenerate atomic and molecular energy levels. A new idea is to build a ``nuclear'' clock based on the ultraviolet transition between very low excited state and ground state in Thorium nucleus. This may allow to improve sensitivity to the variation up to 10 orders of magnitude! Huge enhancement of the variation effects is also possible in cold atomic and molecular collisions near Feschbach resonance.

  7. Constant-pressure Blowers

    Science.gov (United States)

    Sorensen, E

    1940-01-01

    The conventional axial blowers operate on the high-pressure principle. One drawback of this type of blower is the relatively low pressure head, which one attempts to overcome with axial blowers producing very high pressure at a given circumferential speed. The Schicht constant-pressure blower affords pressure ratios considerably higher than those of axial blowers of conventional design with approximately the same efficiency.

  8. String Scale Cosmological Constant

    OpenAIRE

    Chalmers, Gordon

    2006-01-01

    The cosmological constant is an unexplained until now phenomena of nature that requires an explanation through string effects. The apparent discrepancy between theory and experiment is enourmous and has already been explained several times by the author including mechanisms. In this work the string theory theory of abolished string modes is documented and given perturbatively to all loop orders. The holographic underpinning is also exposed. The matching with the data of the LIGO and D0 experi...

  9. Optical lattice clock with Strontium atoms; Horloge a reseau optique a atomes de strontium

    Energy Technology Data Exchange (ETDEWEB)

    Baillard, X

    2008-01-15

    This thesis presents the latest achievements regarding the optical lattice clock with Strontium atoms developed at LNE-SYRTE. After a review of the different types of optical clocks that are currently under development, we stress on the concept of optical lattice clock which was first imagined for Sr{sup 87} using the {sup 1}S{sub 0} {yields} {sup 3}P{sub 0} transition. We exhibit the features of this atom, in particular the concept of magic wavelength for the trap, and the achievable performances for this kind of clock. The second part presents the experimental aspects, insisting particularly on the ultra-stable laser used for the interrogation of the atoms which is a central part of the experiment. Among the latest improvements, an optical pumping phase and an interrogation phase using a magnetic field have been added in order to refine the evaluation of the Zeeman effect. Finally, the last part presents the experimental results. The last evaluation of the clock using Sr{sup 87} atoms allowed us to reach a frequency accuracy of 2.6*10{sup -15} and a measurement in agreement with the one made at JILA (Tokyo university) at the 10{sup -15} level. On another hand, thanks to recent theoretical proposals, we made a measurement using the bosonic isotope Sr{sup 88} by adapting the experimental setup. This measurement represents the first evaluation for this type of clock, with a frequency accuracy of 7*10{sup -14}. (author)

  10. The Hubble Constant.

    Science.gov (United States)

    Jackson, Neal

    2015-01-01

    I review the current state of determinations of the Hubble constant, which gives the length scale of the Universe by relating the expansion velocity of objects to their distance. There are two broad categories of measurements. The first uses individual astrophysical objects which have some property that allows their intrinsic luminosity or size to be determined, or allows the determination of their distance by geometric means. The second category comprises the use of all-sky cosmic microwave background, or correlations between large samples of galaxies, to determine information about the geometry of the Universe and hence the Hubble constant, typically in a combination with other cosmological parameters. Many, but not all, object-based measurements give H0 values of around 72-74 km s(-1) Mpc(-1), with typical errors of 2-3 km s(-1) Mpc(-1). This is in mild discrepancy with CMB-based measurements, in particular those from the Planck satellite, which give values of 67-68 km s(-1) Mpc(-1) and typical errors of 1-2 km s(-1) Mpc(-1). The size of the remaining systematics indicate that accuracy rather than precision is the remaining problem in a good determination of the Hubble constant. Whether a discrepancy exists, and whether new physics is needed to resolve it, depends on details of the systematics of the object-based methods, and also on the assumptions about other cosmological parameters and which datasets are combined in the case of the all-sky methods.

  11. Universe of constant

    Science.gov (United States)

    Yongquan, Han

    2016-10-01

    The ideal gas state equation is not applicable to ordinary gas, it should be applied to the Electromagnetic ``gas'' that is applied to the radiation, the radiation should be the ultimate state of matter changes or initial state, the universe is filled with radiation. That is, the ideal gas equation of state is suitable for the Singular point and the universe. Maybe someone consider that, there is no vessel can accommodate radiation, it is because the Ordinary container is too small to accommodate, if the radius of your container is the distance that Light through an hour, would you still think it can't accommodates radiation? Modern scientific determinate that the radius of the universe now is about 1027 m, assuming that the universe is a sphere whose volume is approximately: V = 4.19 × 1081 cubic meters, the temperature radiation of the universe (cosmic microwave background radiation temperature of the universe, should be the closest the average temperature of the universe) T = 3.15k, radiation pressure P = 5 × 10-6 N / m 2, according to the law of ideal gas state equation, PV / T = constant = 6 × 1075, the value of this constant is the universe, The singular point should also equal to the constant Author: hanyongquan

  12. Study of barium bismuth titanate prepared by mechanochemical synthesis

    Directory of Open Access Journals (Sweden)

    Lazarević Z.Ž.

    2009-01-01

    Full Text Available Barium-bismuth titanate, BaBi4Ti4O15 (BBT, a member of Aurivillius bismuth-based layer-structure perovskites, was prepared from stoichiometric amounts of barium titanate and bismuth titanate obtained via mechanochemical synthesis. Mechanochemical synthesis was performed in air atmosphere in a planetary ball mill. The reaction mechanism of BaBi4Ti4O15 and the preparation and characteristics of BBT ceramic powders were studied using XRD, Raman spectroscopy, particle analysis and SEM. The Bi-layered perovskite structure of BaBi4Ti4O15 ceramic forms at 1100 °C for 4 h without a pre-calcination step. The microstructure of BaBi4Ti4O15 exhibits plate-like grains typical for the Bi-layered structured material and spherical and polygonal grains. The Ba2+ addition leads to changes in the microstructure development, particularly in the change of the average grain size.

  13. Structural, dielectric and magnetic properties of Cr-Zn doped strontium hexa-ferrites for high frequency applications

    Energy Technology Data Exchange (ETDEWEB)

    Asghar, G. [Applied Thermal Physics Laboratory, Department of Physics, COMSATS Institute of Information Technology, Islamabad 44000 (Pakistan); Anis-ur-Rehman, M., E-mail: rehmananis@hotmail.com [Applied Thermal Physics Laboratory, Department of Physics, COMSATS Institute of Information Technology, Islamabad 44000 (Pakistan)

    2012-06-15

    M-type strontium hexa-ferrite nano particles with composition SrFe{sub 12-2x}Cr{sub x}Zn{sub x}O{sub 19} (X = 0.0, 0.2, 0.4, 0.6, 0.8) were prepared by co-precipitation method and are reported for the first time. X-ray diffraction analysis confirmed the successful substitution of Cr and Zn ions in the strontium hexa-ferrite lattice. Structural morphology studied by scanning electron micrographs revealed that Cr-Zn doping inhabits the grain growth. Dielectric measurements were taken as a function of frequency in the range (10 kHz to 3 MHz). Both dielectric constants and dielectric losses were found to be decreasing with the increase in Cr-Zn concentration. As Cr-Zn doping favored the decrease in dielectric losses to a large extent (0.32-0.02) so the strontium hexa-ferrite with these dopants is very useful for high frequency applications. The frequency dependent ac conductivity increases sharply at higher frequencies due to increase in hopping frequency of electrons and decrease with the increase in doping concentration and this is due to decrease in Fe{sup 2+} ions. Temperature dependent dc electrical resistivity measurements showed a decreasing trend with the increase in Cr-Zn concentration. The M-H loop indicated that both coercivity and saturation magnetization were decreased with the increase in doping concentration. The former was decreased due to increase in grain size and later was decreased due to weak and non-magnetic cations distribution on interstitial sites.

  14. Liquid-Phase Processing of Barium Titanate Thin Films

    Science.gov (United States)

    Harris, David Thomas

    Processing of thin films introduces strict limits on the thermal budget due to substrate stability and thermal expansion mismatch stresses. Barium titanate serves as a model system for the difficulty in producing high quality thin films because of sensitivity to stress, scale, and crystal quality. Thermal budget restriction leads to reduced crystal quality, density, and grain growth, depressing ferroelectric and nonlinear dielectric properties. Processing of barium titanate is typically performed at temperatures hundreds of degrees above compatibility with metalized substrates. In particular integration with silicon and other low thermal expansion substrates is desirable for reductions in costs and wider availability of technologies. In bulk metal and ceramic systems, sintering behavior has been encouraged by the addition of a liquid forming second phase, improving kinetics and promoting densification and grain growth at lower temperatures. This approach is also widespread in the multilayer ceramic capacitor industry. However only limited exploration of flux processing with refractory thin films has been performed despite offering improved dielectric properties for barium titanate films at lower temperatures. This dissertation explores physical vapor deposition of barium titanate thin films with addition of liquid forming fluxes. Flux systems studied include BaO-B2O3, Bi2O3-BaB2O 4, BaO-V2O5, CuO-BaO-B2O3, and BaO-B2O3 modified by Al, Si, V, and Li. Additions of BaO-B2O3 leads to densification and an increase in average grain size from 50 nm to over 300 nm after annealing at 900 °C. The ability to tune permittivity of the material improved from 20% to 70%. Development of high quality films enables engineering of ferroelectric phase stability using residual thermal expansion mismatch in polycrystalline films. The observed shifts to TC match thermodynamic calculations, expected strain from the thermal expansion coefficients, as well as x-ray diffract measurements

  15. An overview on the progresses of high performance barium titanate/polymer composites%高性能钛酸钡/聚合物复合材料的研究进展

    Institute of Scientific and Technical Information of China (English)

    张亮; 肖定全

    2012-01-01

    具有高介电常数(k)的钛酸钡/聚合物复合材料,兼有钛酸钡陶瓷和聚合物的各自优势,是一种有广泛应用前景的电子材料,因而备受关注。综合给出了近5年来高性能钛酸钡/聚合物复合材料的研究进展,分析指出了原材料选择、制备工艺及其对复合材料介电性能的影响,概括介绍了这类复合材料的主要应用,预测展望了其未来的发展趋势。%Barium titanate/polymer composites with high dielectric constant (k) were very promising electronic materials because the composites combined the advantages of barium titanate ceramics and polymers individual- ly. In this paper, the research progresses of high performance barium titanate/polymer composites in recent five years are outlined, the choosing of raw materials and the preparation technologies and their influence on the die- lectric properties of the composites are pointed out, the major applications of the composites are introduced, and the development trend and the future prospect of barium titanate/polymer composites are reviewed.

  16. Studies of ferroelectric and dielectric properties of pure and doped barium titanate prepared by sol-gel method

    Energy Technology Data Exchange (ETDEWEB)

    Bisen, Supriya; Mishra, Ashutosh; Jarabana, Kanaka M. [School of Physics, Vigyan Bhawan, Devi Ahilya University, Khandwa Road Indore-452001 (India)

    2016-05-23

    In this work, Barium Titanate (BaTiO{sub 3}) powders were synthesized via Sol-Gel auto combustion method using citric acid as a chelating agent. We study the behavior of ferroelectric and dielectric properties of pure and doped BaTiO{sub 3} on different concentration. To understand the phase and structure of the powder calcined at 900°C were characterized by X-ray Diffraction shows that tetragonal phase is dominant for pure and doped BTO and data fitted by Rietveld Refinement. Electric and Dielectric properties were characterized by P-E Hysteresis and Dielectric measurement. In P-E measurement ferroelectric loop tracer applied for different voltage. The temperature dependant dielectric constant behavior was observed as a function of frequency recorded on hp-Hewlett Packard 4192A, LF impedance, 5Hz-13Hz analyzer.

  17. Biomimetic synthesis of calcium-strontium apatite hollow nanospheres

    Institute of Scientific and Technical Information of China (English)

    2010-01-01

    In this work,calcium-strontium apatite (Sr-HA) hollow nanospheres were synthesized by a facile biomimetic method.The structure and property of Sr-HA were characterized by FESEM,TEM,HRTEM,XRD and FT-IR spectroscopy.The influences of different ratios of calcium and strontium on the morphologies of the Sr-HA products were investigated.The experimental results revealed that the hollow spherical Sr-HA,with a size of 30-120 nm in diameter,could be synthesized when the molar ratio of Ca/Sr was 1:1.The possible formation mechanism of the hollow Sr-HA was proposed.The drug release experiments indicated that the hollow spherical Sr-HA had the property of sustained release.

  18. Growth of strontium oxalate crystals in agar–agar gel

    Indian Academy of Sciences (India)

    P V Dalal; K B Saraf

    2011-04-01

    Single crystals of strontium oxalate have been grown by using strontium chloride and oxalic acid in agar–agar gel media at ambient temperature. Different methods for growing crystals were adopted. The optimum conditions were employed in each method by varying concentration of gel and reactants, and gel setting time etc. Transparent prismatic bi-pyramidal platy-shaped and spherulite crystals were obtained in various methods. The grown crystals were characterized with the help of FT–IR studies and monoclinic system of crystals were supported with lattice parameters = 9.67628 Å, = 6.7175 Å, = 8.6812 Å, = 113.566°, and = 521.84 Å3 calculated from X-ray diffractogram.

  19. Migration Behaviour of Strontium in Czech Bentonite Clay

    Directory of Open Access Journals (Sweden)

    Lucie Baborova

    2016-09-01

    Full Text Available The study deals with sorption and diffusion behaviour of strontium in Czech bentonite B75. The study is a part of a research on reactive transport of radioactive contaminants in barrier materials of a deep geological repository of radioactive waste in the Czech Republic. Series of sorption and diffusion experiments with Sr and non-activated Ca bentonite B75 produced in the Czech Republic were performed in two background solutions (CaCl2 and NaCl. On the basis of sorption batch experiments the kinetics of strontium sorption on bentonite was assessed and the sorption isotherms for various experimental conditions were obtained. As a result of performed diffusion experiments the parameters of diffusion (i.e. effective diffusion coefficient De and apparent diffusion coefficient Da were determined. The observed discrepancies between sorption characteristics obtained from the sorption and diffusion experiments are discussed.

  20. Strontium isotopic identification of water-rock interaction and ground water mixing.

    Science.gov (United States)

    Frost, Carol D; Toner, Rachel N

    2004-01-01

    87Sr/86Sr ratios of ground waters in the Bighorn and Laramie basins' carbonate and carbonate-cemented aquifer systems, Wyoming, United States, reflect the distinctive strontium isotope signatures of the minerals in their respective aquifers. Well water samples from the Madison Aquifer (Bighorn Basin) have strontium isotopic ratios that match their carbonate host rocks. Casper Aquifer ground waters (Laramie Basin) have strontium isotopic ratios that differ from the bulk host rock; however, stepwise leaching of Casper Sandstone indicates that most of the strontium in Casper Aquifer ground waters is acquired from preferential dissolution of carbonate cement. Strontium isotope data from both Bighorn and Laramie basins, along with dye tracing experiments in the Bighorn Basin and tritium data from the Laramie Basin, suggest that waters in carbonate or carbonate-cemented aquifers acquire their strontium isotope composition very quickly--on the order of decades. Strontium isotopes were also used successfully to verify previously identified mixed Redbeds-Casper ground waters in the Laramie Basin. The strontium isotopic compositions of ground waters near Precambrian outcrops also suggest previously unrecognized mixing between Casper and Precambrian aquifers. These results demonstrate the utility of strontium isotopic ratio data in identifying ground water sources and aquifer interactions.

  1. Remarkable Strontium B-Site Occupancy in FerroelectricPb(Zr1-xTix)O3 Solid Solutions Doped with Cryolite-Type StrontiumNiobate

    Energy Technology Data Exchange (ETDEWEB)

    Feltz, A.; Schmidt-Winkel, P.; Schossman, M.; Booth, C.H.; Albering, J.

    2007-04-26

    New high-performance ferroelectric materials based on Pb(Zr{sub 1-x}Ti{sub x})O{sub 3} (PZT) that are doped with cryolite-type strontium niobate (SNO, Sr{sub 4}(Sr{sub 2-2y/3}Nb{sub 2+2y/3})O{sub 11+y}V{sub 0,1-y} with 0 {le} y {le} 1), hence denoted PZT:SNO, and their microscopic structure are described. The combination of exceptional piezoelectric properties, i.e. a piezoelectric strain constant of d{sub 33} {approx} 760 pm/V, with excellent stability and degradation resistance makes ferroelectric PZT:SNO solid solutions very attractive for use in novel and innovative piezoelectric actuator and transducer applications. Extended X-ray absorption fine-structure (EXAFS) analyses of PZT:SNO samples revealed that {approx}10 % of the Sr cations occupy the nominal B-sites of the perovskite-type PZT host lattice. This result was supported by EXAFS analyses of both a canonical SrTiO{sub 3} perovskite and two SNO model and reference compounds. Fit models that do not account for Sr cations on B-sites were ruled out. A clear Sr-Pb peak in Fourier transformed EXAFS data visually confirmed this structural model. The generation of temporary oxygen vacancies and the intricate defect chemistry induced by SNO-doping of PZT are crucial for the exceptional materials properties exhibited by PZT:SNO materials.

  2. Dieletric and magnetic properties of Zn-Ti substituted M-type barium hexaferrite

    Energy Technology Data Exchange (ETDEWEB)

    Dube, Charu Lata; Kashyap, Subhash C.; Pandya, D.K. [Department of Physics, Indian Institute of Technology Delhi, New Delhi 110016 (India); Dube, D.C. [Electronics and Communication Department, Institute of Technology and Management, Gurgaon-122017 (India)

    2009-11-15

    The Zn-Ti substituted barium hexaferrite polycrystalline samples have been synthesized by solid-state reaction method. The complex permittivity and permeability measurements are carried out on the BaFe{sub 12-2x}Zn{sub x}Ti{sub x}O{sub 19} (0.2 {<=} x {<=} 0.6) samples in the microwave frequency range of 8-13 GHz by cavity perturbation technique. The observed abnormal dielectric behavior, i.e., an increasing tendency of dielectric constant with frequency has been attributed to the mixed conduction. The effect of Zn-Ti substitution on the permittivity and dielectric loss has been investigated in the frequency range of 1 kHz-1 MHz as well. The increase in concentration of Zn-Ti dopants monotonically increases both the permittivity and the permeability in the investigated frequency ranges, which can be attributed to increased polarizability and unpinning of the domain walls, respectively. (Abstract Copyright [2009], Wiley Periodicals, Inc.)

  3. Effects of strontium ranelate on spinal osteoarthritis progression.

    Science.gov (United States)

    Bruyere, O; Delferriere, D; Roux, C; Wark, J D; Spector, T; Devogelaer, J-P; Brixen, K; Adami, S; Fechtenbaum, J; Kolta, S; Reginster, J-Y

    2008-03-01

    The aim of this study was to determine whether a 3-year treatment with strontium ranelate could delay the progression of spinal osteoarthritis (OA). This study was a post-hoc analysis of pooled data from the Spinal Osteoporosis Therapeutic Intervention (SOTI) and TReatment Of Peripheral OSteoporosis (TROPOS) trials performed on 1105 women with osteoporosis and concomitant radiological spinal OA at baseline, and for whom lumbar x-rays were available at baseline and over the 3-year treatment period. The presence and severity of osteophytes, disc space narrowing and sclerosis in the lumbar intervertebral spaces was graded according to a validated method, and an overall OA score was calculated for each intervertebral space. Back pain (measured on a five-point Likert scale only in SOTI) and health-related quality of life (SF-36 questionnaire) were assessed at baseline and after 3 years. Patients who suffered an incident or progressive vertebral fracture during the study were excluded from the analysis. The proportion of patients with worsening overall spinal OA score was reduced by 42% in the strontium ranelate group, compared with placebo (RR, 0.58; 95% CI, 0.42 to 0.79; p = 0.0005). Significantly more patients in the strontium ranelate group experienced an improvement in back pain after 3 years, compared with placebo (p = 0.03), while no significant difference was observed in terms of health-related quality of life between these patient groups. The results of this post-hoc analysis suggest that strontium ranelate could reduce the progression of the radiographic features of spinal OA and back pain in women with osteoporosis and prevalent spinal OA.

  4. Collision-induced shifts of Rydberg levels of strontium

    Energy Technology Data Exchange (ETDEWEB)

    Marafi, M; Bhatia, K S; Makdisi, Y Y; Philips, G [Department of Physics, Kuwait University, PO Box 5969, Safat, 13060 (Kuwait)

    2003-05-14

    Measurements of spectral line shifts induced by collisions with rare gas perturbers are reported. High Rydberg states were prepared by multiphoton excitation using an excimer pumped tunable dye laser. A thermionic detector inside a heat pipe was used to collect the ionization products resulting from excited states. Analysis of the data for the shifts of the absorption transition to 5snd {sup 1}D{sub 2} states in strontium is presented.

  5. Collision-induced shifts of Rydberg levels of strontium

    Science.gov (United States)

    Marafi, M.; Bhatia, K. S.; Makdisi, Y. Y.; Philips, G.

    2003-05-01

    Measurements of spectral line shifts induced by collisions with rare gas perturbers are reported. High Rydberg states were prepared by multiphoton excitation using an excimer pumped tunable dye laser. A thermionic detector inside a heat pipe was used to collect the ionization products resulting from excited states. Analysis of the data for the shifts of the absorption transition to 5snd 1D 2 states in strontium is presented.

  6. Treatment of metastatic bone pain with strontium-89.

    Science.gov (United States)

    Robinson, R G; Spicer, J A; Preston, D F; Wegst, A V; Martin, N L

    1987-01-01

    We have utilized 89Sr as palliative treatment for bone pain secondary to metastatic cancer in the skeleton of over 200 patients. The best results have been in patients with carcinoma of the prostate (80% response rate) and breast (89%). Results in a small number of patients with a variety of other cell types were not nearly as encouraging. Strontium-89 provides excellent palliation in the management of bone pain secondary to prostate and breast carcinoma.

  7. Effect of Strontium Nitrate on Extremely Slow Strobe Compositions

    Science.gov (United States)

    2017-01-01

    describes the evaluation of the slow strobe’s pulse rate , based on the mesh size of the metal powder and the effect of the variation of strontium...Increasing potassium vs pulse rate ...........................................................................8 TABLES 1. Orion’s Flashing...solution of nitrocellulose in acetone was used as a binder for all mixes. Batches were dried overnight in an oven at 150 °F. After drying, the mixes were

  8. Dielectric and thermal studies on gel grown strontium tartrate pentahydrate crystals

    Indian Academy of Sciences (India)

    A Firdous; I Quasim; M M Ahmad; P N Kotru

    2010-08-01

    Results of dielectric and thermal studies on strontium tartrate pentahydrate crystals are described. The value of dielectric constant is shown to be independent of temperature till 360 K at all the frequencies (110–700 kHz) of the applied a.c. field. It increases abruptly achieving a peak value of 25.5 at 100 kHz; the peak value being strongly dependent on frequency. In the temperature range, 87 < < 117°C, the value of ' falls suggesting a transition at around 100°C or so. The dielectric constant, ', of the material is shown to be frequency dependent but temperature independent in the pre- or post-c range 87 < < 117°C, suggesting that the contribution towards polarization may be due to ionic or space charge polarization which gets eliminated at higher frequencies. The ferroelectric transition is supported by the results of thermoanalytical studies. It is explained that crystallographic change due to polymorphic phase transition may be occurring in the material, besides the change due to loss of water molecules, which leads to the dielectric anomaly at around 100°C. Coats–Redfern approximation method is applied for obtaining non-isothermal kinetic parameters leading to calculation of activation energies corresponding to three decomposition stages of material in the temperature ranging from 379–1113 K.

  9. The Hubble Constant

    Directory of Open Access Journals (Sweden)

    Neal Jackson

    2015-09-01

    Full Text Available I review the current state of determinations of the Hubble constant, which gives the length scale of the Universe by relating the expansion velocity of objects to their distance. There are two broad categories of measurements. The first uses individual astrophysical objects which have some property that allows their intrinsic luminosity or size to be determined, or allows the determination of their distance by geometric means. The second category comprises the use of all-sky cosmic microwave background, or correlations between large samples of galaxies, to determine information about the geometry of the Universe and hence the Hubble constant, typically in a combination with other cosmological parameters. Many, but not all, object-based measurements give H_0 values of around 72–74 km s^–1 Mpc^–1, with typical errors of 2–3 km s^–1 Mpc^–1. This is in mild discrepancy with CMB-based measurements, in particular those from the Planck satellite, which give values of 67–68 km s^–1 Mpc^–1 and typical errors of 1–2 km s^–1 Mpc^–1. The size of the remaining systematics indicate that accuracy rather than precision is the remaining problem in a good determination of the Hubble constant. Whether a discrepancy exists, and whether new physics is needed to resolve it, depends on details of the systematics of the object-based methods, and also on the assumptions about other cosmological parameters and which datasets are combined in the case of the all-sky methods.

  10. Strontium isotope analysis of archaeological fauna at the Erlitou site

    Institute of Scientific and Technical Information of China (English)

    ZHAO ChunYan; YANG Jie; YUAN Jing; LI ZhiPeng; XU Hong; ZHAO HaiTao; CHEN GuoLiang

    2012-01-01

    The Erlitou site is located at Yanshi City,Henan Province.This site is a large settlement site of Erlitou culture,and it is dated to 3800-3500 a BP.Five kinds of domestic animals,i.e.,dogs,pigs,sheep,goats,and cattle were found from the site.In this paper,two problems have emerged in studies involving the estimation of local isotope levels and the distinction of migrants from locals.Tooth enamel samples fron 17 domestic animals individuals were analyzed for strontium isotope ratio (87Sr/86Sr),by the thermal ionization mass spectrometry,including 10 pigs,5 sheep and 2 cattle.The results show that the mean 87Sr/86Sr ratios of 10 pigs enamel samples were 0.712078,Based on the local strontium isotopes ratio range determined by the mean 87Sr/86Sr ratios ±2σrof 10 pig enamel samples (0.712256-.711900),we found that five sheep and one cattle from the Erlitou site fell well outside the local strontium isotopes ratio range and were considered to be non-local.

  11. Lifetimes of ultra-long-range strontium Rydberg molecules

    CERN Document Server

    Camargo, F; Ding, R; Sadeghpour, H R; Yoshida, S; Burgdörfer, J; Dunning, F B; Killian, T C

    2015-01-01

    The lifetimes of the lower-lying vibrational states of ultralong-range strontium Rydberg molecules comprising one ground-state 5s2 1S0 atom and one Rydberg atom in the 5s38s 3S1 state are reported. The molecules are created in an ultracold gas held in an optical dipole trap and their numbers determined using ?eld ionization, the product electrons being detected by a microchannel plate. The measurements show that, in marked contrast to earlier measurements involving rubidium Rydberg molecules, the lifetimes of the low-lying molecular vibrational states are very similar to those of the parent Rydberg atoms. This results because the strong p-wave resonance in low-energy electronrubidium scattering, which plays an important role in determining the molecular lifetimes, is not present for strontium. The absence of this resonance o?ers advantages for experiments involving strontium Rydberg atoms as impurities in quantum gases and for testing theories of molecular formation and decay.

  12. Production of very-high-n strontium Rydberg atoms

    Science.gov (United States)

    Ye, S.; Zhang, X.; Killian, T. C.; Dunning, F. B.; Hiller, M.; Yoshida, S.; Nagele, S.; Burgdörfer, J.

    2013-10-01

    The production of very-high-n (n˜300-500) strontium Rydberg atoms is explored using a crossed-laser-atom-beam geometry. n1S0 and n1D2 states are created by two-photon excitation via the 5s5p 1P1 intermediate state using radiation with wavelengths of ˜461 and ˜413 nm. Rydberg atom densities as high as ˜3×105 cm-3 have been achieved, sufficient that Rydberg-Rydberg interactions can become important. The isotope shifts in the Rydberg series limits are determined by tuning the 461-nm light to preferentially excite the different strontium isotopes. Photoexcitation in the presence of an applied electric field is examined. The initially quadratic Stark shift of the n1P1 and n1D2 states becomes near-linear at higher fields and the possible use of n1D2 states to create strongly polarized, quasi-one-dimensional electronic states in strontium is discussed. The data are analyzed with the aid of a two-active-electron (TAE) approximation. The two-electron Hamiltonian, within which the Sr2+ core is represented by a semi-empirical potential, is numerically diagonalized allowing the calculation of the energies of high-n Rydberg states and their photoexcitation probabilities.

  13. Production of very-high-$n$ strontium Rydberg atoms

    CERN Document Server

    Ye, Shuzhen; Killian, Thomas C; Dunning, F Barry; Hiller, Moritz; Yoshida, Shuhei; Nagele, Stefan; Burgdörfer, Joachim

    2013-01-01

    The production of very-high-$n$, $n\\sim300$-500, strontium Rydberg atoms is explored using a crossed laser-atom beam geometry. $n$$^{1}$S$_{0}$ and $n$$^{1}$D$_{2}$ states are created by two-photon excitation via the 5s5p $^{1}$P$_{1}$ intermediate state using radiation with wavelengths of $\\sim$~461 and $\\sim$ 413 nm. Rydberg atom densities as high as $\\sim 3 \\times 10^{5}$ cm$^{-3}$ have been achieved, sufficient that Rydberg-Rydberg interactions can become important. The isotope shifts in the Rydberg series limits are determined by tuning the 461 nm light to preferentially excite the different strontium isotopes. Photoexcitation in the presence of an applied electric field is examined. The initially quadratic Stark shift of the $n$$^{1}$P$_{1}$ and $n$$^{1}$D$_{2}$ states becomes near-linear at higher fields and the possible use of $n{}^{1}$D$_{2}$ states to create strongly-polarized, quasi-one-dimensional electronic states in strontium is discussed. The data are analyzed with the aid of a two-active-elect...

  14. Allyl strontium compounds: synthesis, molecular structure and properties.

    Science.gov (United States)

    Jochmann, Phillip; Davin, Julien P; Maslek, Stefanie; Spaniol, Thomas P; Sarazin, Yann; Carpentier, Jean-Francois; Okuda, Jun

    2012-08-14

    The synthesis and attempted isolation of neutral bis(allyl)strontium [Sr(C(3)H(5))(2)] (1) resulted in the isolation of potassium tris(allyl)strontiate K[Sr(C(3)H(5))(3)] (2). In situ generated 1 shows a pronounced Brønsted basicity, inducing polymerisation of THF. Ate complex 2 crystallises as [K(THF)(2){Sr(C(3)H(5))(3)}(THF)](∞) (2·(THF)(3)). The salt-like solid state structure of 2·(THF)(3) comprises a two-dimensional network of (μ(2)-η(3):η(3)-C(3)H(5))(-) bridged potassium and strontium centres. Synthesis of allyl complexes 1 and 2 utilised SrI(2), [Sr(TMDS)(2)] (3) (TMDS = tetramethyldisilazanide), and [Sr(HMDS)(2)] (HMDS = hexamethyldisilazanide) as strontium precursors. The solid state structure of previously reported [Sr(TMDS)(2)] (3) was established by X-ray single crystal analysis as a dissymmetric dimer of [Sr(2)(TMDS)(4)(THF)(3)] (3·(THF)(3)) with multiple Si-HSr agostic interactions. The presence of ether ligands (THF, 18-crown-6) influenced the Si-HSr resonances in the NMR spectra of the amido complex 3.

  15. Spaces of constant curvature

    CERN Document Server

    Wolf, Joseph A

    2010-01-01

    This book is the sixth edition of the classic Spaces of Constant Curvature, first published in 1967, with the previous (fifth) edition published in 1984. It illustrates the high degree of interplay between group theory and geometry. The reader will benefit from the very concise treatments of riemannian and pseudo-riemannian manifolds and their curvatures, of the representation theory of finite groups, and of indications of recent progress in discrete subgroups of Lie groups. Part I is a brief introduction to differentiable manifolds, covering spaces, and riemannian and pseudo-riemannian geomet

  16. Barium stable isotopes in the global ocean: Tracer of Ba inputs and utilization

    Science.gov (United States)

    Hsieh, Yu-Te; Henderson, Gideon M.

    2017-09-01

    Barium has been used as a biogeochemical tracer for alkalinity, productivity, and riverine inputs in the ocean, but its oceanic cycle remains poorly constrained. Barium stable isotope measurements may improve the use of Ba as a tracer and better constrain the cycling of Ba, but data are only available in limited regions of the oceans. In this study, we present dissolved seawater Ba isotopic compositions in a sample collection spanning the North Atlantic, South Atlantic, North Pacific and Southern Oceans. Compiled global upper-ocean [Ba] data show a relatively constant [Ba] (35-45 nM) in the near-surface waters throughout the global ocean, with the exception of areas near river inputs or strong upwelling. The relatively uniform distribution of [Ba] in the upper ocean seawater indicates that Ba removal is slow relative to supply and mixing, and implies that near-surface Ba isotope values are controlled by basin-scale balances rather than by regional or short-term processes. Seawater Ba isotopic compositions show a large variation of δ 138 / 134 Ba values ranging from 0.24 to 0.65‰, and a tight relationship with [Ba]. This global relationship can be simply modelled assuming a primary deep Southern Ocean source for Ba to yield a maximum isotope fractionation of α = 1.00058 ± 0.00010 (α =seawater 138/134Ba/particle 138/134Ba). This suggested isotope fractionation during Ba removal from seawater is larger than implied by laboratory measurement during barite formation, suggesting additional fractionating phases or a two-stage fractionation process. Riverine input from the Rio de la Plata to the South Atlantic has a signature of δ 138 / 134 Ba = - 0.06- 0.11 ‰, which is too light to explain the heavy values (>0.58‰) observed in the surface open ocean. Globally, the Ba isotope composition of the upper ocean waters is correlated with the fraction of Ba utilization at the basin scale (which varies from water (≈0.25‰) trace mixing and allow identification of non

  17. Preparation of Barium Titanate Nanopowder through Thermal Decomposition of Peroxide Precursor and Its Formation Mechanism

    Institute of Scientific and Technical Information of China (English)

    PENG, Yangxi; CHEN, Qiyuan; LIU, Shijun

    2009-01-01

    H_2TiO_3 was dissolved in the mixture of hydrogen formed peroxide and ammonia under the pH range of 8-10 with a transparent yellow solution formed. When an equivalent mole of Ba~(2+) solution was added into the yellow solution, the precipitate produced was the peroxide precursor of barium titanate. The cubic nanopowder of barium titanate was obtained when the precipitate was washed, stoved, and then calcined at 600 ℃ for 1 h. The peroxide precursor of barium titanate and barium titanate nanopowder prepared were characterized to be BaTi(H_2O_2)_2O_3 by TGA-DTA, XRD, TEM, SEM, and XREDS. The peroxide precursor of barium titanate was determined to be BaTi(H_2O_2)_2O_3. The particle size of the barium titanate nanopowder, the calcined product of BaTi(H_2O_2)_2O_3, was in the range of 20-40 nm. A formation mechanism of the barium titanate nanopowder through thermal decomposition of its peroxide precursor was proposed and then validated.

  18. Bio-based barium alginate film: Preparation, flame retardancy and thermal degradation behavior.

    Science.gov (United States)

    Liu, Yun; Zhang, Chuan-Jie; Zhao, Jin-Chao; Guo, Yi; Zhu, Ping; Wang, De-Yi

    2016-03-30

    A bio-based barium alginate film was prepared via a facile ionic exchange and casting approach. Its flammability, thermal degradation and pyrolysis behaviors, thermal degradation mechanism were studied systemically by limiting oxygen index (LOI), vertical burning (UL-94), microscale combustion calorimetry (MCC), thermogravimetric analysis (TGA) coupled with Fourier transform infrared analysis (FTIR) and pyrolysis-gas chromatography-mass spectrometry (Py-GC-MS). It showed that barium alginate film had much higher LOI value (52.0%) than that of sodium alginate film (24.5%). Moreover, barium alginate film passed the UL-94 V-0 rating, while the sodium alginate film showed no classification. Importantly, peak of heat release rate (PHRR) of barium alginate film in MCC test was much lower than that of sodium alginate film, suggested that introduction of barium ion into alginate film significantly decreased release of combustible gases. TG-FTIR and Py-GC-MS results indicated that barium alginate produced much less flammable products than that of sodium alginate in whole thermal degradation procedure. Finally, a possible degradation mechanism of barium alginate had been proposed.

  19. Strontium isoscapes in The Netherlands. Spatial variations in 87Sr/86Sr as a proxy for palaeomobility

    NARCIS (Netherlands)

    Kootker, Lisette M.; van Lanen, Rowin J.; Kars, Henk; Davies, Gareth R.

    2016-01-01

    Strontium isotope analysis has been successfully applied to archaeological questions of residential mobility and animal husbandry for over three decades. To obtain a full understanding of variations in archaeological samples, spatial variations in bioavailable strontium should be accurately mapped o

  20. Magnetic properties of Ni substituted Y-type barium ferrite

    Energy Technology Data Exchange (ETDEWEB)

    Won, Mi Hee; Kim, Chul Sung, E-mail: cskim@kookmin.ac.kr [Department of Physics, Kookmin University, Seoul 136-702 (Korea, Republic of)

    2014-05-07

    Y-type barium hexaferrite is attractive material for various applications, such as high frequency antennas and RF devices, because of its interesting magnetic properties. Especially, Ni substituted Y- type hexaferrites have higher magnetic ordering temperature than other Y-type. We have investigated macroscopic and microscopic properties of Y-type barium hexaferrite. Ba{sub 2}Co{sub 2−x}Ni{sub x}Fe{sub 12}O{sub 22} (x = 0, 0.5, 1.0, 1.5, and 2.0) samples are prepared by solid-state reaction method and studied by X-ray diffraction (XRD), vibrating sample magnetometer, and Mössbauer spectroscopy, as well as a network analyzer for high frequency characteristics. The XRD pattern is analyzed by Rietveld refinement method and confirms the hexagonal structure with R-3m. The hysteresis curve shows ferrimagnetic behavior. Saturation magnetization (M{sub s}) decreases with Ni contents. Ni{sup 2+}, which preferentially occupies the octahedral site with up-spin sub-lattice, has smaller spin value S of 1 than Co{sup 2+} having S = 3/2. The zero-field-cooled (ZFC) measurement of Ba{sub 2}Co{sub 1.5}Ni{sub 0.5}Fe{sub 12}O{sub 22} shows that Curie and spin transition temperatures are found to be 718 K and 209 K, respectively. The Curie temperature T{sub C} is increased with Ni contents, while T{sub S} is decreased with Ni. The Mössbauer spectra were measured at various temperatures and fitted by using a least-squares method with six sextet of six Lorentzian lines for Fe sites, corresponding to the 3b{sub VI}, 6c{sub IV}*, 6c{sub VI}, 18h{sub VI}, 6c{sub IV}, and 3a{sub IV} sites at below T{sub C}. From Mössbauer measurements, we confirmed the spin state of Fe ion to be Fe{sup 3+} and obtained the isomer shift (δ), magnetic hyperfine field (H{sub hf}), and the occupancy ratio of Fe ions at six sub-lattices. The complex permeability and permittivity are measured between 100 MHz and 4 GHz, suggesting that Y-type barium hexaferrite is promising for antenna

  1. Magnetic properties of Ni substituted Y-type barium ferrite

    Science.gov (United States)

    Won, Mi Hee; Kim, Chul Sung

    2014-05-01

    Y-type barium hexaferrite is attractive material for various applications, such as high frequency antennas and RF devices, because of its interesting magnetic properties. Especially, Ni substituted Y- type hexaferrites have higher magnetic ordering temperature than other Y-type. We have investigated macroscopic and microscopic properties of Y-type barium hexaferrite. Ba2Co2-xNixFe12O22 (x = 0, 0.5, 1.0, 1.5, and 2.0) samples are prepared by solid-state reaction method and studied by X-ray diffraction (XRD), vibrating sample magnetometer, and Mössbauer spectroscopy, as well as a network analyzer for high frequency characteristics. The XRD pattern is analyzed by Rietveld refinement method and confirms the hexagonal structure with R-3m. The hysteresis curve shows ferrimagnetic behavior. Saturation magnetization (Ms) decreases with Ni contents. Ni2+, which preferentially occupies the octahedral site with up-spin sub-lattice, has smaller spin value S of 1 than Co2+ having S = 3/2. The zero-field-cooled (ZFC) measurement of Ba2Co1.5Ni0.5Fe12O22 shows that Curie and spin transition temperatures are found to be 718 K and 209 K, respectively. The Curie temperature TC is increased with Ni contents, while TS is decreased with Ni. The Mössbauer spectra were measured at various temperatures and fitted by using a least-squares method with six sextet of six Lorentzian lines for Fe sites, corresponding to the 3bVI, 6cIV*, 6cVI, 18hVI, 6cIV, and 3aIV sites at below TC. From Mössbauer measurements, we confirmed the spin state of Fe ion to be Fe3+ and obtained the isomer shift (δ), magnetic hyperfine field (Hhf), and the occupancy ratio of Fe ions at six sub-lattices. The complex permeability and permittivity are measured between 100 MHz and 4 GHz, suggesting that Y-type barium hexaferrite is promising for antenna applications in UHF band.

  2. Dielectric characterization of low-loss calcium strontium titanate fibers produced by laser floating zone technique for wireless communication

    Energy Technology Data Exchange (ETDEWEB)

    Amaral, F. [Department of Physics and I3N, University of Aveiro, 3810-193, Aveiro (Portugal); Polytechnic Institute of Coimbra, 3000-271, Coimbra (Portugal); Valente, M.A.; Costa, L.C.; Costa, F.M. [Department of Physics and I3N, University of Aveiro, 3810-193, Aveiro (Portugal)

    2014-09-15

    Wireless communication technology assisted to a huge development during the last two decades, responding to the growing demand for small size and low weight devices such as cell phones and global positioning systems. The need for miniaturization and higher autonomy resulted in the development of new dielectric oxide ceramics with very specific properties, to be applied as dielectric resonators in filters, oscillators, and antennas. Some crucial properties as a high quality factor, high dielectric constant, and near zero temperature coefficient of resonant frequency must be considered during the selection of the appropriate materials. The present work deals with the preparation of calcium titanate (CaTiO{sub 3}), strontium titanate (SrTiO{sub 3}), and calcium strontium titanate (Ca{sub x}Sr{sub 1-x}TiO{sub 3}) fibers produced by laser floating zone (LFZ) technique. Our results show that fibers grown at lower pulling rates exhibit higher ε', for all the studied frequency range, including the microwave region. Moreover, the quality factor is always high envisaging the possibility to include these materials in future wireless device applications. (copyright 2014 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  3. Strontium incorporates at sites critical for bone mineralization in rats with renal failure

    Energy Technology Data Exchange (ETDEWEB)

    Oste, Line; Verberckmoes, Steven C.; Behets, Geert J.; Dams, Geert; Bervoets, An R.; De Broe, Marc E.; D' Haese, Patrick C. [Faculty of Medicine, Antwerp University (Belgium); Van Hoof, Viviane O. [Department of Biochemistry, Antwerp University Hospital (Belgium); Bohic, Sylvain [European Synchrotron Radiation Facility, Grenoble (France); Drakopoulos, Michael [Diamond Light Source, Oxfordshire (United Kingdom)

    2007-01-15

    We previously demonstrated the development of a mineralization defect during strontium administration and its reversibility after withdrawal in rats with chronic renal failure. Recently, strontium ranelate has been introduced as a therapeutic agent for osteoporosis. However, caution has to be taken, as this bone disorder mainly develops in elderly people who may present a moderately decreased renal function. In order to assess the ultra-structural localization of strontium in bone and thereby to get a better insight into the element's systemic effects on bone, synchrotron-based x-ray micro-fluorescence was applied, which showed that after 2 weeks of strontium loading (2 g l{sup -1} in drinking water) in rats with renal failure, concomitant with the development of impaired mineralization, the element was localized mainly at the outer edge of the mineralized bone, while after longer loading periods, a more homogeneous distribution was found. After washout, strontium was found at sites deeper within the trabeculae, while newly deposited low-strontium-containing mineral was found at the outer edges. Synchrotron x-ray micro-diffraction analysis showed that strontium is incorporated in the apatite crystal lattice through exchange with calcium. The results show that strontium is initially incorporated in bone at sites of active bone mineralization, close to the osteoid/mineralization front.Most likely, strontium binds to matrix proteins serving as crystal nucleation points and by hetero-ionic substitution with calcium within the hydroxyapatite crystals, thereby impairing further hydroxyapatite formation. After withdrawal, strontium is released from these sites, by which mineralization is restored and the previously formed strontium-containing hydroxyapatite is buried under a new layer of mineralized bone. (authors)

  4. Barium ferrite nanoparticles prepared by self-propagating low-temperature combustion method and its characterization

    Indian Academy of Sciences (India)

    P M Prithviraj Swamy; S Basavaraja; Vijayanand Havanoor; N V Srinivas Rao; R Nijagunappa; A Venkataraman

    2011-12-01

    The barium ferrite particles were prepared using a self-propagating low-temperature combustion method using polyethylene glycol (PEG) as a fuel. The process was investigated with simultaneous thermogravimetric-differential thermal analysis (TG–DTA). The crystalline structure, morphology and the magnetic properties of the barium ferrite particles were studied by means of X-ray diffraction (XRD), scanning electron microscopy (SEM), transmission electron microscopy (TEM) and SQUID susceptometer. The results show that the ignition temperature of PEG is lower compared with other combustion methods and gives nanocrystalline barium ferrite.

  5. A Comparative Study on Magnetostructural Properties of Barium Hexaferrite Powders Prepared by Polyethylene Glycol

    Directory of Open Access Journals (Sweden)

    Zehra Durmus

    2014-01-01

    Full Text Available Nanocrystalline particles of barium hexaferrite were synthesized by a sol-gel combustion route using nitrate-citrate gels prepared from metal nitrates and citric acid solutions with Fe/Ba molar ratio 12. The present paper aims to study the effect of addition of polyethylene glycol (PEG solutions with different molecular weights (MW: 400, 2000, and 10.000 g/mol on magnetostructural properties of barium hexaferrite. The formation of the barium hexaferrite was inspected using X-ray diffraction (XRD analysis, Fourier transform infrared (FT-IR analysis, thermogravimetric (TGA analysis, scanning electron microscopy (SEM analysis and vibrating sample magnetometer (VSM analysis for magnetic measurements.

  6. Addition of methyl cellulose enema to double-contrast barium imaging of sigmoid diverticulosis

    Energy Technology Data Exchange (ETDEWEB)

    Olsson, R. [Malmoe Univ. Hospital (Sweden). Dept. of Diagnostic Radiology; Adnerhill, I. [Malmoe Univ. Hospital (Sweden). Dept. of Diagnostic Radiology; Bjoerkdahl, P. [Malmoe Univ. Hospital (Sweden). Dept. of Diagnostic Radiology; Ekberg, O. [Malmoe Univ. Hospital (Sweden). Dept. of Diagnostic Radiology; Fork, F.T. [Malmoe Univ. Hospital (Sweden). Dept. of Diagnostic Radiology

    1997-01-01

    Double-contrast barium enema has a reduced sensitivity in patients with severe sigmoid diverticulosis. Therefore a carboxy methyl cellulose enema was employed after the conventional double-contrast examination in 15 patients with sigmoid diverticulosis. A significant increase in lumen diameter and a superior removal of barium residue from the diverticulas facilitated the interpretation of the sigmoid loops. Conclusion: The addition of methyl cellulose enema to double-contrast barium imaging improves diagnostic imaging in diverticulosis by expanding the lumen and emptying the diverticulas. (orig.).

  7. The Hubble Constant

    Directory of Open Access Journals (Sweden)

    Jackson Neal

    2007-09-01

    Full Text Available I review the current state of determinations of the Hubble constant, which gives the length scale of the Universe by relating the expansion velocity of objects to their distance. In the last 20 years, much progress has been made and estimates now range between 60 and 75 km s^-1 Mpc^-1, with most now between 70 and 75 km s^-1 Mpc^-1, a huge improvement over the factor-of-2 uncertainty which used to prevail. Further improvements which gave a generally agreed margin of error of a few percent rather than the current 10% would be vital input to much other interesting cosmology. There are several programmes which are likely to lead us to this point in the next 10 years.

  8. When constants are important

    Energy Technology Data Exchange (ETDEWEB)

    Beiu, V.

    1997-04-01

    In this paper the authors discuss several complexity aspects pertaining to neural networks, commonly known as the curse of dimensionality. The focus will be on: (1) size complexity and depth-size tradeoffs; (2) complexity of learning; and (3) precision and limited interconnectivity. Results have been obtained for each of these problems when dealt with separately, but few things are known as to the links among them. They start by presenting known results and try to establish connections between them. These show that they are facing very difficult problems--exponential growth in either space (i.e. precision and size) and/or time (i.e., learning and depth)--when resorting to neural networks for solving general problems. The paper will present a solution for lowering some constants, by playing on the depth-size tradeoff.

  9. Constant Proportion Portfolio Insurance

    DEFF Research Database (Denmark)

    Jessen, Cathrine

    2014-01-01

    Portfolio insurance, as practiced in 1987, consisted of trading between an underlying stock portfolio and cash, using option theory to place a floor on the value of the position, as if it included a protective put. Constant Proportion Portfolio Insurance (CPPI) is an option-free variation...... on the theme, originally proposed by Fischer Black. In CPPI, a financial institution guarantees a floor value for the “insured” portfolio and adjusts the stock/bond mix to produce a leveraged exposure to the risky assets, which depends on how far the portfolio value is above the floor. Plain-vanilla portfolio...... insurance largely died with the crash of 1987, but CPPI is still going strong. In the frictionless markets of finance theory, the issuer’s strategy to hedge its liability under the contract is clear, but in the real world with transactions costs and stochastic jump risk, the optimal strategy is less obvious...

  10. Decay constants in geochronology

    Institute of Scientific and Technical Information of China (English)

    IgorM.Villa; PaulR.Renne

    2005-01-01

    Geologic time is fundamental to the Earth Sciences, and progress in many disciplines depends critically on our ability to measure time with increasing accuracy and precision. Isotopic geochronology makes use of the decay of radioactive nuclides as a help to quantify the histories of rock, minerals, and other materials. Both accuracy and precision of radioisotopic ages are, at present, limited by those of radioactive decay constants. Modem mass spectrometers can measure isotope ratios with a precision of 10-4 or better. On the other hand, the uncertainties associated with direct half-life determinations are, in most cases, still at the percent level. The present short note briefly summarizes progress and problems that have been encountered during the Working Group's activity.

  11. Structural and functional characterization of barium zirconium titanate / epoxy composites

    Directory of Open Access Journals (Sweden)

    Filiberto González Garcia

    2011-12-01

    Full Text Available The dielectric behavior of composite materials (barium zirconium titanate / epoxy system was analyzed as a function of ceramic concentration. Structure and morphologic behavior of the composites was investigated by X-ray Diffraction (XRD, Fourier transformed infrared spectroscopy (FT-IR, Raman spectroscopy, field emission scanning electron microscopy (FE-SEM and transmission electron microscopy (TEM analyses. Composites were prepared by mixing the components and pouring them into suitable moulds. It was demonstrated that the amount of inorganic phase affects the morphology of the presented composites. XRD revealed the presence of a single phase while Raman scattering confirmed structural transitions as a function of ceramic concentration. Changes in the ceramic concentration affected Raman modes and the distribution of particles along into in epoxy matrix. Dielectric permittivity and dielectric losses were influenced by filler concentration.

  12. Effect of Nb on barium titanate prepared from citrate solutions

    Directory of Open Access Journals (Sweden)

    Stojanović Biljana D.

    2002-01-01

    Full Text Available The influence of the addition of dopants on the microstructure development and electrical properties of BaTiO3 doped with 0.2, 0.4, 0.6, 0.8 mol% of Nb and 0.01 mol% of Mn based compounds was studied. Doped barium titanate was prepared using the polymeric precursor method from citrate solutions. The powders calcined at 700°C for 4 hours were analysed by infrared (IR spectroscopy to verify the presence of carbonates, and by X-ray diffraction (XRD for phase formation. The phase composition, microstructure and dielectric properties show a strong dependence on the amount of added niobium.

  13. Analysis of barium hydroxide and calcium hydroxide slurry carbonation reactors

    Energy Technology Data Exchange (ETDEWEB)

    Patch, K.D.; Hart, R.P.; Schumacher, W.A.

    1980-05-01

    The removal of CO/sub 2/ from air was investigated by using a continuous-agitated-slurry carbonation reactor containing either barium hydroxide (Ba(OH)/sub 2/) or calcium hydroxide (Ca(OH)/sub 2/). Such a process would be applied to scrub /sup 14/CO/sub 2/ from stack gases at nuclear-fuel reprocessing plants. Decontamination factors were characterized for reactor conditions which could alter hydrodynamic behavior. An attempt was made to characterize reactor performance with models assuming both plug flow and various degrees of backmixing in the gas phase. The Ba(OH)/sub 2/ slurry enabled increased conversion, but apparently the process was controlled under some conditions by phenomena differing from those observed for carbonation by Ca(OH)/sub 2/. Overall reaction mechanisms are postulated.

  14. A buffer gas cooled beam of barium monohydride

    Science.gov (United States)

    Iwata, Geoffrey; Tarallo, Marco; Zelevinsky, Tanya

    2016-05-01

    Significant advances in direct laser cooling of diatomic molecules have opened up a wide array of molecular species to precision studies spanning many-body physics, quantum collisions and ultracold dissociation. We present a cryogenic beam source of barium monohydride (BaH), and study laser ablation of solid precursor targets as well as helium buffer gas cooling dynamics. Additionally, we cover progress towards a molecular magneto-optical trap, with spectroscopic studies of relevant cooling transitions in the B2 Σ molecules, including resolution of hyperfine structure and precision measurements of the vibrational Frank-Condon factors. Finally, we examine the feasibility of photo dissociation of trapped BaH molecules to yield optically accessible samples of ultracold hydrogen.

  15. Communication: Barium ions and helium nanodroplets: solvation and desolvation.

    Science.gov (United States)

    Zhang, Xiaohang; Drabbels, Marcel

    2012-08-07

    The solvation of Ba(+) ions created by the photoionization of barium atoms located on the surface of helium nanodroplets has been investigated. The excitation spectra corresponding to the 6p (2)P(1/2) ← 6s (2)S(1/2) and 6p (2)P(3/2) ← 6s (2)S(1/2) transitions of Ba(+) are found to be identical to those recorded in bulk He II [H. J. Reyher, H. Bauer, C. Huber, R. Mayer, A. Schafer, and A. Winnacker, Phys. Lett. A 115, 238 (1986)], indicating that the ions formed at the surface of the helium droplets become fully solvated by the helium. Time-of-flight mass spectra suggest that following the excitation of the solvated Ba(+) ions, these are being ejected from the helium droplets either as bare Ba(+) ions or as small Ba(+)He(n) (n < 20) complexes.

  16. Infrared Spectroscopic Characterization of Calcium and Barium Hydrazone Complexes

    Directory of Open Access Journals (Sweden)

    *A. Adeniyi

    2013-06-01

    Full Text Available Hydrazones have attracted considerable interest on account of their biological activities. Introduction of calcium and barium metal ions into m- and p-nitrobenzoic hydrazones is expected to modify these biological properties for enhanced activity and versatility. The ligands were synthesized from the parent acids. The complexes have been characterized using C, H and N microanalyses and IR spectrometry. The IR spectral data of the ligands and complexes revealed bonding via the C=O and C=N groups. The suggested metal to ligand stoichiometries are: [M (m-NBHx]Cl2.yH2O, x, y = 1 and 4 for M = Ca; x, y = 2 and 3 for M = Ba respectively. [M(p-NBHx]Cl2.yH2O, x, y = 1 and 12 for M = Ca; x, y = 1 and 3 for M = Ba respectively. The structural deductions are tentative pending future X-ray structural studies.

  17. Synthesis and optical study of barium magnesium aluminate blue phosphors

    Science.gov (United States)

    Jeet, Suninder; Sharma, Manoj; Pandey, O. P.

    2015-05-01

    Europium doped barium magnesium aluminate (BaMgAl10O17:Eu2+) phosphor was prepared via solution combustion method at 550°C using urea as a fuel. Morphological and optical properties of the prepared sample was studied by X-ray diffraction (XRD), Transmission electron microscopy (TEM) and Photoluminescence spectroscopy (PL). XRD result showed the formation of pure phase BaMgAl10O17(JCPDS 26-0163) along with an additional phase BaAl2O4(JCPDS 01-082-1350). TEM image indicated the formation of faceted particles with average particle size 40 nm. From PL spectra, a broad emission band obtained at about 450 nm attributes to 4f6 5d → 4f7 transition of Eu2+ which lies in the blue region of the visible spectrum.

  18. Synthesis and optical study of barium magnesium aluminate blue phosphors

    Energy Technology Data Exchange (ETDEWEB)

    Jeet, Suninder, E-mail: suninder.jeet@thapar.edu; Pandey, O. P., E-mail: oppandey@thapar.edu [School of Physics and Materials Science, Thapar University, Patiala (147003), Punjab (India); Sharma, Manoj, E-mail: manojnarad@sggswu.org [Department of Nanotechnology, Sri Guru Granth Sahib World University, Fatehgarh Sahib(146406), Punjab (India)

    2015-05-15

    Europium doped barium magnesium aluminate (BaMgAl{sub 10}O{sub 17}:Eu{sup 2+}) phosphor was prepared via solution combustion method at 550°C using urea as a fuel. Morphological and optical properties of the prepared sample was studied by X-ray diffraction (XRD), Transmission electron microscopy (TEM) and Photoluminescence spectroscopy (PL). XRD result showed the formation of pure phase BaMgAl{sub 10}O{sub 17}(JCPDS 26-0163) along with an additional phase BaAl{sub 2}O{sub 4}(JCPDS 01-082-1350). TEM image indicated the formation of faceted particles with average particle size 40 nm. From PL spectra, a broad emission band obtained at about 450 nm attributes to 4f{sup 6} 5d → 4f{sup 7} transition of Eu{sup 2+} which lies in the blue region of the visible spectrum.

  19. Influence of Barium Hexaferrite on Magnetic Properties of Hydroxyapatite Ceramics.

    Science.gov (United States)

    Jarupoom, P; Jaita, P

    2015-11-01

    Hydroxyapatite (HA) powders was derived from natural bovine bone by sequence of thermal processes. The barium hexaferrite (BF) find magnetic powders were added into HA powders in ratio of 1-3 vol.%. The HA-BF ceramics were prepared by a solid state reaction method and sintered at 1250 degrees C for 2 h. Effects of BF additive on structural, physical and magnetic properties of HA ceramics were investigated. X-ray diffraction revealed that all HA-BF samples showed a main phase of high purity hydroxyapatite [Ca10(PO4)6(OH)2] with calcium and phosphate molar ratio of 1.67. The addition of BF into HA inhibited grain growth and caused an improvement of mechanical properties. The M-H hysteresis loops also showed an improvement in magnetic behavior for higher content of BF. Moreover, in vitro bioactivity test indicated that the 2-3 vol.% sample may be suitable for biological applications.

  20. Barium titanate nanocomposite capacitor FY09 year end report.

    Energy Technology Data Exchange (ETDEWEB)

    Stevens, Tyler E.; DiAntonio, Christopher Brian; Yang, Pin; Chavez, Tom P.; Winter, Michael R.; Monson, Todd C.; Roesler, Alexander William; Fellows, Benjamin D.

    2009-11-01

    This late start RTBF project started the development of barium titanate (BTO)/glass nanocomposite capacitors for future and emerging energy storage applications. The long term goal of this work is to decrease the size, weight, and cost of ceramic capacitors while increasing their reliability. Ceramic-based nanocomposites have the potential to yield materials with enhanced permittivity, breakdown strength (BDS), and reduced strain, which can increase the energy density of capacitors and increase their shot life. Composites of BTO in glass will limit grain growth during device fabrication (preserving nanoparticle grain size and enhanced properties), resulting in devices with improved density, permittivity, BDS, and shot life. BTO will eliminate the issues associated with Pb toxicity and volatility as well as the variation in energy storage vs. temperature of PZT based devices. During the last six months of FY09 this work focused on developing syntheses for BTO nanoparticles and firing profiles for sintering BTO/glass composite capacitors.

  1. Physico-chemical study of barium (II) dipivaloylmethanate nature

    Energy Technology Data Exchange (ETDEWEB)

    Fedotova, N.E. [Rossijskaya Akademiya Nauk, Novosibirsk (Russian Federation). Inst. of Inorganic Chemistry; Igumenov, I.K. [Rossijskaya Akademiya Nauk, Novosibirsk (Russian Federation). Inst. of Inorganic Chemistry; Mamatyuk, V.I. [Rossijskaya Akademiya Nauk, Novosibirsk (Russian Federation). Inst. of Inorganic Chemistry; Sidorenko, G.V. [Rossijskaya Akademiya Nauk, Novosibirsk (Russian Federation). Inst. of Inorganic Chemistry

    1995-06-01

    A physico-chemical research of bis-(dipivaloylmethanato)barium(II) (Ba(thd){sub 2}) has been carried out from the point of its use in CVD processes as a precursor (thermal stability, immunity to external effects and etc.). The optimal conditions for synthesis, purification and storage have been found. It has been shown, that the sublimated product presents a mixture of several modifications with the main phase of a composition Ba{sub 4}(thd){sub 8}. At a lowered pressure the sublimated product is preserved without decomposition for a long time. In the air it is a monomer of a composition Ba(thd){sub 2}*2H{sub 2}O, decomposing in the course of time with forming a free ligand or a diketone (C{sub 8}H{sub 21}O{sub 2}) depending on the way of purification of the initial compound. (orig.).

  2. Barium depletion study on impregnated cathodes and lifetime prediction

    Energy Technology Data Exchange (ETDEWEB)

    Roquais, J.M.; Poret, F.; Doze, R. le; Ricaud, J.L.; Monterrin, A.; Steinbrunn, A

    2003-06-15

    In the thermionic cathodes used in cathode ray-tubes (CRTs), barium is the key element for the electronic emission. In the case of the dispenser cathodes made of a porous tungsten pellet impregnated with Ba, Ca aluminates, the evaporation of Ba determines the cathode lifetime with respect to emission performance in the CRT. The Ba evaporation results in progressive depletion of the impregnating material inside the pellet. In the present work, the Ba depletion with time has been extensively characterized over a large range of cathode temperature. Calculations using the depletion data allowed modeling of the depletion as a function of key parameters. The link between measured depletion and emission in tubes has been established, from which an end-of-life criterion was deduced. Taking modeling into account, predicting accelerated life-tests were performed using high-density maximum emission current (MIK)

  3. Dissociation behavior of protons incorporated in yttrium doped barium zirconate

    Science.gov (United States)

    Ishiyama, T.; Kishimoto, H.; Develos-Bagarinao, K.; Yamaji, K.; Yamaguchi, T.; Fujishiro, Y.

    2017-08-01

    The dissociation behavior of protons incorporated in yttrium-doped barium zirconate (BZY20) was investigated via combination of in-situ diffuse reflectance Fourier transform infrared spectroscopy (FT-IR) and evolved gas analysis. The vicinities of dopant or host ions were considered as sites of proton dissolution. The temperature dependence of the dissociation of protons from each site was evaluated. Protons which were considered to have dissolved in the vicinity of dopant ions were easily removed and dissociated as water. On the other hand, those which dissolved in the vicinity of host ions were dissociated as hydrogen at high temperatures. Such dissociation behavior was also detected after using D2O saturated gas for pre-treatment. These results suggest that some protons which dissolved in the perovskite oxide could dissociate as hydrogen without forming oxygen vacancies. (131words)

  4. Preparation and Characterization of Nano-particle Substituted Barium Hexaferrite

    CERN Document Server

    Atassi, Yomen; Tally, Mohammad

    2014-01-01

    High density magnetic recording requires high coercivity magnetic media and small particle size. Barium hexaferrite has been considered as a leading candidate material because of its chemical stability, fairly large crystal anisotropy and suitable magnetic characteristics. In this work, we present the preparation of the hexagonal ferrite BaFe12O19 and one of its derivative; the Zn-Sn substituted hexaferrite by the chemical co-precipitation method. The main advantage of this method on the conventional glass-ceramic one, resides in providing a small enough particle size for magnetic recording. We demonstrate using the X-ray diffraction patterns that the particle size decreases when substituting the hexaferrite by the Zn-Sn combination. This may improve the magnetic properties of the hexaferrite as a medium for HD magnetic recording

  5. Barium and carbon fluxes in the Canadian Arctic Archipelago

    Science.gov (United States)

    Thomas, Helmuth; Shadwick, Elizabeth; Dehairs, Frank; Lansard, Bruno; Mucci, Alfonso; Navez, Jacques; Gratton, Yves; Prowe, Friederike; Chierici, Melissa; Fransson, Agneta; Papakyriakou, Tim N.; Sternberg, Erika; Miller, Lisa A.; Tremblay, Jean-ÉRic; Monnin, Christophe

    2011-09-01

    The seasonal and spatial variability of dissolved Barium (Ba) in the Amundsen Gulf, southeastern Beaufort Sea, was monitored over a full year from September 2007 to September 2008. Dissolved Ba displays a nutrient-type behavior: the maximum water column concentration is located below the surface layer. The highest Ba concentrations are typically observed at river mouths, the lowest concentrations are found in water masses of Atlantic origin. Barium concentrations decrease eastward through the Canadian Arctic Archipelago. Barite (BaSO4) saturation is reached at the maximum dissolved Ba concentrations in the subsurface layer, whereas the rest of the water column is undersaturated. A three end-member mixing model comprising freshwater from sea-ice melt and rivers, as well as upper halocline water, is used to establish their relative contributions to the Ba concentrations in the upper water column of the Amundsen Gulf. Based on water column and riverine Ba contributions, we assess the depletion of dissolved Ba by formation and sinking of biologically bound Ba (bio-Ba), from which we derive an estimate of the carbon export production. In the upper 50 m of the water column of the Amundsen Gulf, riverine Ba accounts for up to 15% of the available dissolved Ba inventory, of which up to 20% is depleted by bio-Ba formation and export. Since riverine inputs and Ba export occur concurrently, the seasonal variability of dissolved Ba in the upper water column is moderate. Assuming a fixed organic carbon to bio-Ba flux ratio, carbon export out of the surface layer is estimated at 1.8 ± 0.45 mol C m-2 yr-1. Finally, we propose a climatological carbon budget for the Amundsen Gulf based on recent literature data and our findings, the latter bridging the surface and subsurface water carbon cycles.

  6. Study on Performance of Empore~(TM) Strontium Rad Disks-Ⅱ

    Institute of Scientific and Technical Information of China (English)

    2011-01-01

    EmporeTM Strontium Rad disks produced by 3M Company contain a strontium-selective crown ether extractant loaded on silica particles that are embedded in an inert PTFE matrix. The disks allow aqueous solutions to pass through in high flow rate. It makes

  7. Full-Scale and Bench-Scale Studies on the Removal of Strontium from Water (abstract)

    Science.gov (United States)

    Strontium (Sr) is a natural and commonly occurring alkaline earth metal which has an oxidation state of +2 under normal environmental conditions. Stable strontium is suspended in water and is dissolved after water runs through rocks and soil. It behaves very similar to calcium. G...

  8. Marking pike fry otoliths with alizarin complexone and strontium : an evaluation of methods

    DEFF Research Database (Denmark)

    Skov, Christian; Grønkjær, P.; Nielsen, C.

    2001-01-01

    Laboratory experiments demonstrated that both alizarin complexone and strontium are useful in mass marking of pike Esox lucius fry otoliths. Visual detection of alizarin complexone marks was considered more reliable than the quantitative analysis of strontium for differentiating marked and unmarked...

  9. On the similarity between the energy characteristics of strontium and europium

    Science.gov (United States)

    Belyaev, V. N.

    2016-11-01

    The spectra of Eu, Sr, Eu+, and Sr+ are used as examples to demonstrate the similarity between the energy characteristics of these elements. It is shown that europium is identical to strontium in the strong and inhomogeneous magnetic field whose source in lanthanides is their empty and compact 4 f n strontium with no magnetic fields.

  10. Strontium localization in bone tissue studied by X-ray absorption spectroscopy.

    Science.gov (United States)

    Frankær, Christian Grundahl; Raffalt, Anders Christer; Stahl, Kenny

    2014-02-01

    Strontium has recently been introduced as a pharmacological agent for the treatment and prevention of osteoporosis. We determined the localization of strontium incorporated into bone matrix from dogs treated with Sr malonate by X-ray absorption spectroscopy. A new approach for analyzing the X-ray absorption spectra resulted in a compositional model and allowed the relative distribution of strontium in the different bone components to be estimated. Approximately 35-45% of the strontium present is incorporated into calcium hydroxyapatite (CaHA) by substitution of some of the calcium ions occupying highly ordered sites, and at least 30% is located at less ordered sites where only the first solvation shell is resolved, suggesting that strontium is surrounded by only oxygen atoms similar to Sr(2+) in solution. Strontium was furthermore shown to be absorbed in collagen in which it obtains a higher structural order than when present in serum but less order than when it is incorporated into CaHA. The total amount of strontium in the samples was determined by inductively coupled plasma mass spectrometry, and the amount of Sr was found to increase with increasing dose levels and treatment periods, whereas the relative distribution of strontium among the different components appears to be independent of treatment period and dose level.

  11. Synthesis and characterization of strontium carboxylates at room temperature and at high temperature in autoclave vessels

    DEFF Research Database (Denmark)

    Christgau, Stephan; Ståhl, Kenny; Andersen, Jens Enevold Thaulov

    2006-01-01

    -ray crystallography. Optimum conditions were found at T = 120-1400C, a base-to-acid ratio of 1.2 and 15 min. of reaction-time in an autoclave vessel. Large crystals were readily obtained within a time period of hours. The crystal structures of strontium D-glutamate hexahydrate (I) and strontium di-(hydrogen L...

  12. Repumping of ultracold strontium atoms using the ^3P2 - ^3D2 transition

    Science.gov (United States)

    Mickelson, P. G.; Martinez de Escobar, Y. N.; Traverso, A. J.; Killian, T. C.

    2008-05-01

    We discuss recent experiments involving ultracold strontium. Using a commercially-available 3 micron laser, we repump atoms out of the ^3P2 level via the ^3D2 state and gain almost a factor of 10 in the number of atoms in our system. This increase in the signal-to-noise ratio enables improved spectroscopy of strontium in our optical trap.

  13. Origin of absorption peaks in reflection loss spectrum in Ku- frequency band of Co-Zr substituted strontium hexaferrites prepared using sucrose precursor

    Science.gov (United States)

    Narang, Sukhleen Bindra; Pubby, Kunal; Chawla, S. K.; Kaur, Prabhjyot

    2017-03-01

    This study presents the detailed explanation of the factors, contributing towards the absorption peaks in reflection loss spectrum of hexaferrites. Cobalt-Zirconium substituted strontium hexaferrites, synthesized using sucrose precursor sol-gel technique, were analyzed in 12.4-18 GHz frequency range. The concepts of impedance matching through quarter wavelength condition, complex thickness, dielectric phase angle and attenuation constant have been used to determine the location as well as intensity of absorption peaks. This study also demonstrates the potential application of three compositions of this series with doping content (x)==0.0, 0.6 and 0.8 as an effective microwave absorbers in Ku-frequency band.

  14. Effects of strontium-induced stress on marine microalgae Platymonas subcordiformis (Chlorophyta: Volvocales)

    Institute of Scientific and Technical Information of China (English)

    2006-01-01

    Strontium-induced stress in growth and chlorophyll contents ofPlatymonas subcordiformis was investigated under laboratory condition. The results showed that strontium exposure had little influences in general on growth and chlorophyll contents of the algae except for very high Sr concentrations.The maximum biosorption capacity of strontium ranged from 69.62 to 269.18 mg Sr2+/gdry weight. The algal biomass exhibited high uptake capacity of strontium. Total superoxide dismutase (SOD) activity and the content of lipid peroxidation products malondialdehyde (MDA) were significantly different in different treatments. SOD activity reached the highest level at 0.09 mmol/L that was about 55.8 % higher than that in the control. The MDA content increased significantly at 0.36 mmol/L, which was 2.15 times higher than that in the control, indicating a state of oxidative stress. With the increase of strontium concentration,the amount of fatty acids decreased.

  15. Characterization and growth dynamics of barium titanate crystallite on nanometer scale

    Institute of Scientific and Technical Information of China (English)

    Sen Wang; Yue Zhang; Zhen Ji; Yousong Gu; Yunhua Huang; Cheng Zhou

    2005-01-01

    Barium titanate powder on nanometer scale was synthesized by means of co-precipitation. The thermal mass loss, crystal grain growth and phase transition of the barium titanate nanometer powder were investigated by TG (Thermogravimetric)-DTA (Differential scanning calorimetric) and XRD (X-ray powder diffractometer) at different heat treatment temperatures. The results show that amorphous barium titanate powder can transfer into tetragonal symmetry structure after heat treatment. When the heat treatment temperature is below 900℃, the grains grow rapidly because the activation energy at low temperature is greatly less than that at high temperature. By controlling theheat treatment temperature, the optimization of the barium titanate crystallite size and formation of tetragonal phase can be realized.

  16. Severe acute cholangitis after endoscopic sphincterotomy induced by barium examination: A case report

    Institute of Scientific and Technical Information of China (English)

    Zhen-Hai Zhang; Ya-Guang Wu; Cheng-Kun Qin; Zhong-Xue Su; Jian Xu; Guo-Zhe Xian; Shuo-DongWu

    2012-01-01

    Endoscopic sphincterotomy (EST) is considered as a possible etiological factor for severe cholangitis.We herein report a case of severe cholangitis after endoscopic sphincterotomy induced by barium examination.An adult male patient presented with epigastric pain was diagnosed as having choledocholithiasis by ultrasonography.EST was performed and the stone was completely cleaned.Barium examination was done 3d after EST and severe cholangitis appeared 4 h later.The patient was recovered after treated with tienam for 4 d.Barium examination may induce severe cholangitis in patients after EST,although rare,barium examination should be chosen cautiously.Cautions should be also used when EST is performed in patients younger than 50 years to avoid the damage to the sphincter of Oddi.

  17. Progress In Materials Synthesis And Processing Of Barium Titanium Oxide (BaTiO3) and Barium Strontium Titanium Oxide (BaTiSrO3) Films For Uncooled Infrared (IR) Detector Applications

    Science.gov (United States)

    2011-12-01

    This wavelength is ideal for enhancing the near IR photoresponse of solar cells , and we are transitioning this technology to our quantum dot solar ...nanoparticles was also achieved using polyvinylpyrrolidone (PVP), which was found to facilitate the formation of stable colloids of BaTiO3 and thereby...processing parameters with the (pyro)electrical properties and IR responsiveness of the perovskite test structures. Based on the existing and preferred ARL

  18. Influence of granular strontium chloride as additives on some electrical and mechanical properties for pure polyvinyl alcohol

    Indian Academy of Sciences (India)

    A B Elaydy; M Hafez

    2010-04-01

    A matrix composed of polyvinyl-alcohol (PVA) mixed with different concentration ratios of the granular strontium chloride (SrCl2.6H2O) were prepared by casting technique method at room temperature (about 30°C). The electric and dielectric properties such as a.c. electrical conductivity by a conventional method, using Keithly 616 digital electrometer, dielectric constant, and dielectric loss were measured. Calculated equilibrium properties such as lattice constant, bulk modulus and elastic constants are in good agreement with experimental results. The calculated activation energy values agree well with experiment only when the SrCO2 molecules are allowed to displace under strain, indicating the importance of inner strain relaxation. From the elastic constants, theoretical values of the Young’s modulus, shear modulus, Poisson’s ratio, of SrCl2 are obtained. In addition mechanical properties such as Young’s modulus, creep relaxation, and energy stored properties for these samples were also determined at room temperature.

  19. Study of the immunoisolating effects of barium-alginate microencapsulation on rat islets allograft survival

    Institute of Scientific and Technical Information of China (English)

    Mei Zhang; Chao Liu; Cuiping Liu; Youwen Qin; Zhaosun Zhen

    2005-01-01

    Objective: To evaluate the immunoisolating effects of barium-alginate microencapsulation on islets allograft survival. Methods: The nonmicroencapsulated and microencapsulated islets were transplanted under the kidney capsule or intraperitoneally into Wistar rat with STZ-induced diabetes. The blood glucose and insulin secretion of grafts were observed. Graft function was tested by oral rats was associated with normal glucose and insulin profiles in response to OGTT. Conclusion: Microencapsulation with barium-alginate membrane can prolong islet survival and protect islets against allorejection.

  20. Study on Effectiveness of Barium Enema in the Diagnosis of Hirschsprung Disease

    Directory of Open Access Journals (Sweden)

    M. Karami Chanlah

    2005-08-01

    Full Text Available Introduction & Aims: The study aims to investigate barium enema accuracy in diagnosing Hischsprung's disease (HD. Patients & Methods: This study was performed on 58 patients diagnosed with Hischsprung's disease later confirmed by pathology; the patients had undergone surgical operation in the last 3 years. The radiographs were reached from their medical records and were later assessed by a skilled pediatric radiologist. Bar-ium enema findings were also evaluated. Rectosig-moid index with the sign of transitional zone (TZ, and barium evacuation of delayed radiographs were recorded by a radiologist. Results: We measured accuracy of rectosigmoid index in these patients to be 94.8%, the sign of TZ to be 70.7%, and the barium evacuation of delayed radio-graphs to be 100% for diagnosis of HD. Fifty percent of the cases were neonates, 42% infants, and 7% more than 2 years old. Of all the patients, 76% were male and 24% were female. The most common diseases accompanying HD were cardiac abnormalities. We did not find any total aganglionosis. Conclusion & Discussion: Half of the patients were newborn infants. The fact that the ratio is more than usual shows timely diagnosis of the condition by phy-sicians of this center. Barium enema findings in new-borns of our study contradicted significantly the re-searches done in other countries. In this study, it was found that with increasing age, barium enema find-ings would be defined in such a way that in in-fantsover 2 years, it can reach a diagnosis accuracy of up to 100%. Regarding the availability of barium en-ema and its lower costs than other diagnostic meth-ods, its accuracy seems very promising. Our study emphasizes that perhaps with barium enema, we may operate these infants in one stage so that they can get rid of multiphasic operation difficulties.

  1. [Constant scaled-energy spectroscopy of Rydberg atoms in a static electric field].

    Science.gov (United States)

    Cao, Jun-wen; Liu, Xiao-jun; Zhao, Zhi; Zhan, Ming-sheng

    2002-02-01

    In the past years, scaled energy spectroscopy is under active investigation because this method can simplify the analysis of atomic spectra in the external field based on classic mechanics. A fully computer-controlled experimental system to study the constant scaled-energy spectroscopy was established and described in this paper. The excitation energy E and the strength of the external electric field F were controlled synchronously to keep the scaled-energy epsilon = E/square root of F constant. With this system, constant scaled-energy spectra of Strontium Rydberg atoms at epsilon = -3.0 in a static electric field were successfully recorded for the first time, and the recurrence spectra were obtained by a Fourier transform.

  2. Variation in structural and dielectric properties of co-precipitated nanoparticles strontium ferrites due to value of pH

    Energy Technology Data Exchange (ETDEWEB)

    Anis-ur-Rehman, M., E-mail: marehman@comsats.edu.pk [Applied Thermal Physics Laboratory, Department of Physics, COMSATS Institute of Information Technology, Islamabad 44000 (Pakistan); Asghar, G. [Applied Thermal Physics Laboratory, Department of Physics, COMSATS Institute of Information Technology, Islamabad 44000 (Pakistan)

    2011-01-12

    Nanoparticles of strontium ferrites with nominal composition SrFe{sub 12}O{sub 19} were prepared by co-precipitation method, by decreasing pH from 13 to 8 with a regular step of 1. The secondary phase of {alpha}-Fe{sub 2}O{sub 3} was increased with the decrease in pH. The crystallite size estimated from X-rays diffraction data was in the range 52-70 nm, which is much smaller than that already reported. Most of the particles formed had hexagonal structure, as observed by the scanning electron microscopy. Particle size and dielectric loss were increased where as dc electrical resistivity and dielectric constant were decreased with decrease in pH. The results show that the material synthesized with higher pH is phase pure and is potentially more suitable for high frequency applications.

  3. The Interacting and Non-constant Cosmological Constant

    CERN Document Server

    Verma, Murli Manohar

    2009-01-01

    We propose a time-varying cosmological constant with a fixed equation of state, which evolves mainly through its interaction with the background during most of the long history of the universe. However, such interaction does not exist in the very early and the late-time universe and produces the acceleration during these eras when it becomes very nearly a constant. It is found that after the initial inflationary phase, the cosmological constant, that we call as lambda parameter, rolls down from a large constant value to another but very small constant value and further dominates the present epoch showing up in form of the dark energy driving the acceleration.

  4. Strontium iodide gamma ray spectrometers for planetary science (Conference Presentation)

    Science.gov (United States)

    Prettyman, Thomas H.; Rowe, Emmanuel; Butler, Jarrhett; Groza, Michael; Burger, Arnold; Yamashita, Naoyuki; Lambert, James L.; Stassun, Keivan G.; Beck, Patrick R.; Cherepy, Nerine J.; Payne, Stephen A.; Castillo-Rogez, Julie C.; Feldman, Sabrina M.; Raymond, Carol A.

    2016-09-01

    Gamma rays produced passively by cosmic ray interactions and by the decay of radioelements convey information about the elemental makeup of planetary surfaces and atmospheres. Orbital missions mapped the composition of the Moon, Mars, Mercury, Vesta, and now Ceres. Active neutron interrogation will enable and/or enhance in situ measurements (rovers, landers, and sondes). Elemental measurements support planetary science objectives as well as resource utilization and planetary defense initiatives. Strontium iodide, an ultra-bright scintillator with low nonproportionality, offers significantly better energy resolution than most previously flown scintillators, enabling improved accuracy for identification and quantification of key elements. Lanthanum bromide achieves similar resolution; however, radiolanthanum emissions obscure planetary gamma rays from radioelements K, Th, and U. The response of silicon-based optical sensors optimally overlaps the emission spectrum of strontium iodide, enabling the development of compact, low-power sensors required for space applications, including burgeoning microsatellite programs. While crystals of the size needed for planetary measurements (>100 cm3) are on the way, pulse-shape corrections to account for variations in absorption/re-emission of light are needed to achieve maximum resolution. Additional challenges for implementation of large-volume detectors include optimization of light collection using silicon-based sensors and assessment of radiation damage effects and energetic-particle induced backgrounds. Using laboratory experiments, archived planetary data, and modeling, we evaluate the performance of strontium iodide for future missions to small bodies (asteroids and comets) and surfaces of the Moon and Venus. We report progress on instrument design and preliminary assessment of radiation damage effects in comparison to technology with flight heritage.

  5. Quantum Theory without Planck's Constant

    CERN Document Server

    Ralston, John P

    2012-01-01

    Planck's constant was introduced as a fundamental scale in the early history of quantum mechanics. We find a modern approach where Planck's constant is absent: it is unobservable except as a constant of human convention. Despite long reference to experiment, review shows that Planck's constant cannot be obtained from the data of Ryberg, Davisson and Germer, Compton, or that used by Planck himself. In the new approach Planck's constant is tied to macroscopic conventions of Newtonian origin, which are dispensable. The precision of other fundamental constants is substantially improved by eliminating Planck's constant. The electron mass is determined about 67 times more precisely, and the unit of electric charge determined 139 times more precisely. Improvement in the experimental value of the fine structure constant allows new types of experiment to be compared towards finding "new physics." The long-standing goal of eliminating reliance on the artifact known as the International Prototype Kilogram can be accompl...

  6. Synthesis of nonstoichiometric M-type barium ferrite nanobelt by spark plasma sintering method

    Institute of Scientific and Technical Information of China (English)

    ZHAO Wenyu; ZHANG Qingjie; TANG Xinfeng; CHENG Haibin

    2005-01-01

    This study investigated the feasibility of ultrafast crystallization of M-type barium ferrite when the coprecipitation precursors in stoichiometric proportions as BaFe12O19, Fe(OH)3 and BaCO3 nanoparticles, had been heated by spark plasma sintering (SPS) process. The results show that SPS method may realize the ultrafast crystallization of M-type barium ferrite, absolutely prevent the crystallization of intermediate phase α-Fe2O3, and significantly decrease the crystallization temperature of M-type barium ferrite. The sintered samples obtained at 800℃ by sintering the precursors for 10 minutes are a kind of multiphase ferrites composed of major phase M-type barium ferrite and trace amount of BaFe0.24Fe0.76O2.88. It is discovered that M-type barium ferrites in the holes of the sintered samples are in nanobelt microstructure about 100-300 nm in width and several micrometers in length. These M-type barium ferrite nanobelts are non-stoichiometric and may be expressed as BaFe12+Xo19+1.5x (-4.77≤x≤6.50). Their composistions suggest completely random Fe-rich or Ba-rich domains.

  7. Barium swallow study in routine clinical practice: a prospective study in patients with chronic cough

    Directory of Open Access Journals (Sweden)

    Carlos Shuler Nin

    2013-12-01

    Full Text Available OBJECTIVE: To assess the routine use of barium swallow study in patients with chronic cough.METHODS: Between October of 2011 and March of 2012, 95 consecutive patients submitted to chest X-ray due to chronic cough (duration > 8 weeks were included in the study. For study purposes, additional images were obtained immediately after the oral administration of 5 mL of a 5% barium sulfate suspension. Two radiologists systematically evaluated all of the images in order to identify any pathological changes. Fisher's exact test and the chi-square test for categorical data were used in the comparisons.RESULTS: The images taken immediately after barium swallow revealed significant pathological conditions that were potentially related to chronic cough in 12 (12.6% of the 95 patients. These conditions, which included diaphragmatic hiatal hernia, esophageal neoplasm, achalasia, esophageal diverticulum, and abnormal esophageal dilatation, were not detected on the images taken without contrast. After appropriate treatment, the symptoms disappeared in 11 (91.6% of the patients, whereas the treatment was ineffective in 1 (8.4%. We observed no complications related to barium swallow, such as contrast aspiration.CONCLUSIONS: Barium swallow improved the detection of significant radiographic findings related to chronic cough in 11.5% of patients. These initial findings suggest that the routine use of barium swallow can significantly increase the sensitivity of chest X-rays in the detection of chronic cough-related etiologies.

  8. Experimental studies on 3D printing of barium titanate ceramics for medical applications

    Directory of Open Access Journals (Sweden)

    Schult Mark

    2016-09-01

    Full Text Available The present work deals with the 3D printing of porous barium titanate ceramics. Barium titanate is a biocompatible material with piezoelectric properties. Due to insufficient flowability of the starting material for 3D printing, the barium titanate raw material has been modified in three different ways. Firstly, barium titanate powder has been calcined. Secondly, flow additives have been added to the powder. And thirdly, flow additives have been added to the calcined powder. Finally, a polymer has been added to the three materials and specimens have been printed from these three material mixtures. The 3D printed parts were then sintered at 1320°C. The sintering leads to shrinkage which differs between 29.51–71.53% for the tested material mixtures. The porosity of the parts is beneficial for cell growth which is relevant for future medical applications. The results reported in this study demonstrate the possibility to fabricate porous piezoelectric barium titanate parts with a 3D printer that can be used for medical applications. 3D printed porous barium titanate ceramics can especially be used as scaffold for bone tissue engineering, where the bone formation can be promoted by electrical stimulation.

  9. Strontium titanate resistance modulation by ferroelectric field effect

    CERN Document Server

    Marré, D; Bellingeri, E; Pallecchi, I; Pellegrino, L; Siri, A S

    2003-01-01

    Among perovskite oxides strontium titanate (STO) SrTiO sub 3 undergoes a metal-insulator transition at very low carrier concentration and exhibits high mobility values at low temperature. We exploited such electrical properties and the structural compatibility of perovskite oxide materials in realizing ferroelectric field effect epitaxial heterostructures. By pulsed laser deposition, we grew patterned field effect devices, consisting of lanthanum doped STO and Pb(Zr,Ti)O sub 3. Such devices showed a resistance modulation up to 20%, consistent with geometrical parameters and carrier concentration of the semiconducting channel.

  10. Experimental study of strontium sorption on fissure filling material

    Energy Technology Data Exchange (ETDEWEB)

    Eriksen, T.E.; Cui, Daqing [Royal Institute of Technology, Stockholm (Sweden). Dept. of Chemistry

    1994-12-01

    We have carried out a comparative study of sorption and desorption of strontium in groundwater on separated magnetic and size fractions of fissure filling material taken from natural fissures in granitic rock. Complete reversibility of the sorption process was demonstrated by identical Freundlich isotherms, isotopic exchangeability and pH dependence of the distribution coefficients Rd. The sorption was found to be strongly pH dependent in the range 3-11. The pH effect can be accommodated in the sorption model by considering the surface areas and surface charges of the minerals in the fissure filling material. 20 refs, 9 figs, 3 tabs.

  11. Strontium modified biocements with zero order release kinetics.

    Science.gov (United States)

    Hamdan Alkhraisat, Mohammad; Moseke, Claus; Blanco, Luis; Barralet, Jake E; Lopez-Carbacos, Enrique; Gbureck, Uwe

    2008-12-01

    Strontium-substituted beta-TCP with the general formula Ca((3-x))Sr(x)(PO(4))(2) (0brushite (CaHPO(4).2H(2)O). Release experiments under dynamic conditions for up to 15 days revealed the release of Sr(2+) ions at dose ranges of 12-30 ppm with zero order release kinetic. Cement cytocompatibility was investigated by culturing human osteoblast cell line hFOB1.19 on cement surfaces whereas Sr-containing cements were as good as Sr-free cements in providing a template for cell growth and function.

  12. Designing Zeeman slower for strontium atoms - towards optical atomic clock

    CERN Document Server

    Bober, Marcin; Gawlik, Wojciech

    2010-01-01

    We report on design and construction of a Zeeman slower for strontium atoms which will be used in an optical atomic clock experiment. The paper describes briefly required specifications of the device, possible solutions, and concentrates on the chosen design. The magnetic field produced by the built Zeeman slower has been measured and compared with the simulations. The system consisting of an oven and Zeeman slower are designed to produce an atomic beam of 10-12 s-1 flux and final velocity of ~30 m/s.

  13. Spectroscopy of strontium Rydberg states using electromagnetically induced transparency

    OpenAIRE

    Mauger, Sarah; Millen, James; Jones, M. P. A.

    2007-01-01

    We report on the all-optical detection of Rydberg states in a effusive atomic beam of strontium atoms using electromagnetically induced transparency (EIT). Using narrow-linewidth CW lasers we obtain an EIT linewidth of 5 MHz. To illustrate the high spectroscopic resolution offered by this method, we have measured isotope shifts of the 5s18d ^1D_2 and 5s19s ^1S_0 Rydberg states. This technique could be applied to high-resolution, non-destructive measurements of ultra-cold Rydberg gases and pla...

  14. Designing Zeeman slower for strontium atoms - towards optical atomic clock

    OpenAIRE

    Bober, Marcin; Zachorowski, Jerzy; Gawlik, Wojciech

    2010-01-01

    We report on design and construction of a Zeeman slower for strontium atoms which will be used in an optical atomic clock experiment. The paper describes briefly required specifications of the device, possible solutions, and concentrates on the chosen design. The magnetic field produced by the built Zeeman slower has been measured and compared with the simulations. The system consisting of an oven and Zeeman slower are designed to produce an atomic beam of 10-12 s-1 flux and final velocity of...

  15. P-type conductivity in annealed strontium titanate

    Energy Technology Data Exchange (ETDEWEB)

    Poole, Violet M.; Corolewski, Caleb D.; McCluskey, Matthew D., E-mail: mattmcc@wsu.edu [Department of Physics and Astronomy, Washington State University, Pullman, WA 99164-2814 (United States)

    2015-12-15

    Hall-effect measurements indicate p-type conductivity in bulk, single-crystal strontium titanate (SrTiO{sub 3}, or STO) samples that were annealed at 1200°C. Room-temperature mobilities above 100 cm{sup 2}/V s were measured, an order of magnitude higher than those for electrons (5-10 cm{sup 2}/V s). Average hole densities were in the 10{sup 9}-10{sup 10} cm{sup −3} range, consistent with a deep acceptor.

  16. Sputtered (barium(x), strontium(1-x))titanate, BST, thin films on flexible copper foils for use as a non-linear dielectric

    Science.gov (United States)

    Laughlin, Brian James

    Ferroelectric thin film dielectrics have a non-linear DC bias dependent permittivity and can be used as the dielectric between metal electrodes to make tunable Metal-Insulator-Metal (MIM) capacitors. Varactors can be used to change the resonance frequency of a circuit allowing high speed frequency switching intra- and inter-band. 2-D geometric arrays of circuitry, where resonant frequency is independently controlled by tunable elements in each section of the array, allow electromagnetic radiation to be focused and the wave front spatial trajectory controlled. BST thin films varactors allow large DC fields to be applied with modest voltages providing large tunabilities. If ferroelectric thin film based devices are to complement or supplant semiconductor varactors as tunable elements then devices must be synthesized using a low cost processing techniques. The Film on Foil process methodology for depositing BST thin films on copper foil substrates was used to create BST/Cu specimens. Sputtering conditions were determined via BST deposition on platinized silicon. Sputtered BST thin films were synthesized on Cu foil substrates and densified using high T, controlled pO2 anneals. XRD showed the absence of Cu2O in as-deposited, post crystallization annealed, and post "re-ox" annealed state. Data showed a polycrystalline BST microstructure with a 55--80 nm grain size and no copper oxidation. HRTEM imaging qualitatively showed evidence of an abrupt BST/Cu interface free from oxide formation. Dielectric properties of Cu/BST/Pt MIM devices were measured as a function of DC bias, frequency, and temperature. A permittivity of 725 was observed with tunability >3:1 while zero bias tan delta of 0.02 saturating to tan delta 3:1 was maintained. These results provide a route for creating temperature stable capacitors using a BST/Cu embodiment. An effort to reduce surface roughness of copper foil substrates adversely impacted BST film integrity by impairing adhesion. XPS analysis of high surface roughness commercially obtained Cu foils revealed a surface treatment of Zn-Cu-O that was not present on smooth Cu, thus an investigation of surface chemistry was conducted. Sessile drop experiments were performed to characterize Cu-BST adhesion and the effects of metallic Zn and ZnO in this system. The study revealed the work of adhesion of Cu-BST, WCu-BSTa ≈ 0.60 J m-2, an intermediate value relative to noble metals commonly used as electrodes and substrates for electroceramics. Examination of metallic Zn-BST adhesion revealed a dramatic decrease of WZn-BSTa ≈ 0.13 J m-2, while increasing the content of Zn in metallic (Cux,Zn1-x) alloys monotonically reduced WCux,Zn1-x -BSTa . Conversely, a Cu-ZnO interface showed a large work of adhesion, WCu-ZnOa = 2.0 J m-2. These results indicate that a ZnO interlayer between the substrate Cu and the BST thin film provides adequate adhesion for robust films on flexible copper foil substrates. Additionally, this study provided characterization of adhesion for Zn-Al2O3 and Zn-BST; data that does not exist in the open literature. A process has been developed for preparing ultra-smooth copper foils by evaporation and subsequent peel-off of copper metal layers from glass slides. These 15 mum thick substrates exhibited roughness values between 1 and 2 nm RMS and 9 nm RMS over 25 mum2 and 100 mum2 analysis areas, respectively. The deposition and crystallization of BST layers on these ultra-smooth foils is demonstrated. The fully processed dielectric layers exhibited field tunability >5:1, and could withstand fields >750 kV cm-1. High field loss tangents below 0.007 were observed, making these materials excellent candidates for microwave devices. Finally, a process of lamination and contact lithography was used to demonstrate patterning of micron-scale features suitable for microwave circuit element designs.

  17. Effects of surrounding powder in sintering process on the properties of Sb and Mn- doped barium-strontium titanate PTCR ceramics

    Directory of Open Access Journals (Sweden)

    Pornsuda Bomlai

    2006-05-01

    Full Text Available In this research, the effects of surrounding powder used during sintering of Sb and Mn doped bariumstrontium titanate (BST ceramics were studied. The ceramic samples were prepared by a conventional mixed-oxide method and placed on different powders during sintering. Phase formation, microstructure and PTCR behavior of the samples were then observed. Microstructures and PTCR behavior varied with the type of surrounding powder, whereas the crystal structure did not change. The surrounding powder has more effects on the shape of the grain than on the size. The grain size of samples was in the range of 5-20 μm. The most uniform grain size and the highest increase of the ratio of ρmax/ρRT were found to be about 106 for samples which had been sintered on Sb-doped BST powder. This value was an order of magnitude greater than for samples sintered on a powder of the equivalent composition to that of the sample pellet.

  18. DFT studies of calcium(II), strontium(II) and barium(II) benzoates with N,N,N‧,N‧-Tetrakis(2-hydroxyethyl/propyl)ethylenediamine

    Science.gov (United States)

    Obrai, Sangeeta; Kumar, Rakesh; Goyal, Milli; Kaushal, Svati

    2016-06-01

    The computational study of some s-block metal nitrobenzoateate complexes: [Ca(THEEN)(H2O)]2+ (1), [Ca(THPEN)(H2O)2]2+ (2), [Sr(THPEN)(H2O)3]2+ (3), [Ba(THPEN)(H2O)2]22+(4), [Ba(THEEN)(H2O)2]22+ (5), (where THEEN (N,N,N‧,N'-Tetrakis(2-hydroxyethyl)ethylenediamine) and THPEN (N,N,N‧,N'- Tetrakis(2-hydroxypropyl)ethylenediamine) are tetrapodal ligands) is presented here using density functional theory (DFT) in its hybrid form B3LYP. The geometries of the title complexes are described by the quantum-chemical approach using input coordinates obtained from the previously synthesized and X-ray characterized diffraction data of [Ca(THEEN)(H2O)](DNB)2.H2O, [Ca(THPEN)(H2O)2](DNB)2.H2O [Sr(THPEN)(H2O)3](DNB)2, [Ba(THPEN)(H2O)2]2(DNB)4.2H2O and [Ba(THEEN)(H2O)2]2(ONB)4 (where DNB- is 3,5-dinitrobenzoate anion and ONB- is 2-nitrobenzoate). Only the primary coordination sphere of complexes (1) - (5) is optimized in the gaseous state. The calculation of energy gaps of frontier orbitals (HOMO-LUMO), 13C -NMR shifts and vibrational bands is carried out using B3LYP/6-31G**/LANL2DZ level of theory. The calculated geometric and spectral parameters reproduced the experimental data with well-agreement. HOMO-LUMO energy gap suggest that [Ca(THPEN)(H2O)2]2+ (2) is the most stable (HLG = 6.893 eV) among all the similar previously and presently reported complexes.

  19. Librational modes of the water molecules in barium and strontium halide monohydrates, MX 2 · 1H 2O (M = Ba, Sr; X = Cl, Br, I)

    Science.gov (United States)

    Lutz, H. D.; Christian, H.

    1983-09-01

    The IR and Raman spectra of the isotypic alkaline earth halide monohydrates, MX 2 · 1H 2O, with M = Sr, Ba and X = Cl, Br, I, and of deuterated samples are presented for the range 200-700 cm -1 and discussed in terms of normal modes, assignment, coupling, correlation with structure data, and temperature dependence of both the H 2O (D 2O) and the HDO librational modes. The normal modes of the out-of-plane librations of HDO molecules are of the wagging and twisting type rather than H and D out-of-plane vibrations [4], at least for water molecules with C2v or nearly C2v symmetry. Thus the observed H 2O/HDO isotopic shifts can be used as a criterion for assigning the H 2O librations. The librational modes of the halide monohydrates (with tetrahedrally coordinated water oxygen atoms) are found in the order ν Rγ ≫ ν Rt ≫ ν Rr. The intensities of the IR and Raman spectra are in the order Rγ ≫ Rr ≫ Rt (or ˜ Rt in the case of strongly distorted H 2O molecules) and Rt ≫ Rr ≫ Rγ, respectively. Correlations of the H 2O librational modes with structural or bonding data are restricted by frequency shifts due to vibrational coupling and by the fact that the oxygen and the hydrogen atoms of the water molecules are generally affected in a different manner by bond interactions. However, in the case of the twisting vibrations, there are clear correlations with both the size of the metal ions, i.e. increase of ν Rt with decreasing size, and the intermolecular bonding of the hydrogen atoms, as shown by the OH stretching frequencies, i.e. increase of ν Rt with decreasing ν OH.

  20. Effect of growth mechanisms on the deformation of a unit cell and polarization reversal in barium-strontium titanate heterostructures on magnesium oxide

    Science.gov (United States)

    Mukhortov, V. M.; Golovko, Yu. I.; Biryukov, S. V.; Anokhin, A.; Yuzyuk, Yu. I.

    2016-01-01

    The effect of a growth mechanism on the unit cell strain and the related change in the properties of single-crystal Ba0.8Sr0.2TiO3 films grown on MgO substrates according to the Frank-van der Merwe and Volmer-Weber growth mechanisms is studied. The unit cell strain is shown to depend substantially on the film thickness and the growth mechanism. It is found that the same film-substrate pair can be used to vary stresses in the film from two-dimensional tensile to compressive stresses due to a change in the growth mechanism and the film thickness.