WorldWideScience

Sample records for consolidated clayey materials

  1. An experimental study of electrical and dielectric properties of consolidated clayey materials

    International Nuclear Information System (INIS)

    Comparon, L.

    2005-06-01

    This study is devoted to the electrical and dielectric properties of consolidated clays. A better understanding of the conduction and polarization phenomena in clays is necessary to better interpret in situ measurements in terms of water saturation and texture. An experimental study was carried out on synthetic clay samples (kaolinite and smectite) compacted with various water contents, porosities and mineralogical compositions, on a large frequency range, using three laboratory setups. The electrical properties of natural argillites (from ANDRA) were then investigated. We found that the response of the synthetic samples is mainly controlled by water content on the whole frequency range; two polarization phenomena were observed, which were related to the Maxwell-Wagner polarization and the electrical double layer polarization around the clay particles. The electrical response of argillites is more complex; it is controlled by water content but also by the microstructure of the rock. In these rocks, the electrical and dielectric anisotropies are high; anisotropy was also measured for the synthetic clays. The existing models explain the high frequency limit of the dielectric permittivity of the clayey materials, but the low frequency part of the spectra (≤1 MHz) needs theoretical developments. (author)

  2. An experimental study of electrical and dielectric properties of consolidated clayey materials; Etude experimentale des proprietes electriques et dielectriques des materiaux argileux consolides

    Energy Technology Data Exchange (ETDEWEB)

    Comparon, L

    2005-06-15

    This study is devoted to the electrical and dielectric properties of consolidated clays. A better understanding of the conduction and polarization phenomena in clays is necessary to better interpret in situ measurements in terms of water saturation and texture. An experimental study was carried out on synthetic clay samples (kaolinite and smectite) compacted with various water contents, porosities and mineralogical compositions, on a large frequency range, using three laboratory setups. The electrical properties of natural argillites (from ANDRA) were then investigated. We found that the response of the synthetic samples is mainly controlled by water content on the whole frequency range; two polarization phenomena were observed, which were related to the Maxwell-Wagner polarization and the electrical double layer polarization around the clay particles. The electrical response of argillites is more complex; it is controlled by water content but also by the microstructure of the rock. In these rocks, the electrical and dielectric anisotropies are high; anisotropy was also measured for the synthetic clays. The existing models explain the high frequency limit of the dielectric permittivity of the clayey materials, but the low frequency part of the spectra ({<=}1 MHz) needs theoretical developments. (author)

  3. Improving geotechnical properties of clayey soil using polymer material

    Directory of Open Access Journals (Sweden)

    Karim Hussein

    2018-01-01

    Full Text Available This study illustrates the application of polymer material for clayey soil stabilization. The article will focus on studying the strength behavior of the clayey soils reinforced with homogenously polymer fiber. In the current research, “polypropylene” was selected as polymer material to reinforce the natural clay soil. This polymer fiber was added to the clayey soil with four different percentages of (0, 1.5, 3, and 5% by weight of soil. Various tests with different polymer contents were performed to study the effect of using such a polymer as a stabilizing agent on geotechnical properties of clay. As the fiber content increases, the optimum moisture content (OMC is increased while the specific gravity decreases. For Atterberg’s limits, the results indicated increasing liquid limit and plasticity index while decreasing plastic limit with increase in polymer content. The outcomes of the tests also reflected a considerable improvement in the unconfined compressive strength with noticeable improvement in the shear strength parameter (undrained shear strength, cu of the treated soils. The undrained shear strength obtained from treated soil with 5% polymer addition is more than three times that of the untreated soil. With an increase in polymer content, the consolidation parameters (Compression index Cc and recompression index Cr decreases. Finally, the benefit of the reinforcement is increased with increasing polymer fiber content.

  4. Improving geotechnical properties of clayey soil using polymer material

    OpenAIRE

    Karim Hussein; Al-Soudany Kawther

    2018-01-01

    This study illustrates the application of polymer material for clayey soil stabilization. The article will focus on studying the strength behavior of the clayey soils reinforced with homogenously polymer fiber. In the current research, “polypropylene” was selected as polymer material to reinforce the natural clay soil. This polymer fiber was added to the clayey soil with four different percentages of (0, 1.5, 3, and 5%) by weight of soil. Various tests with different polymer contents were per...

  5. FEM validation of a double porosity elastic model for consolidation of structurally complex clayey soils

    Science.gov (United States)

    Callari, C.; Federico, F.

    2000-04-01

    Laboratory consolidation of structured clayey soils is analysed in this paper. The research is carried out by two different methods. The first one treats the soil as an isotropic homogeneous equivalent Double Porosity (DP) medium. The second method rests on the extensive application of the Finite Element Method (FEM) to combinations of different soils, composing 2D or fully 3D ordered structured media that schematically discretize the complex material. Two reference problems, representing typical situations of 1D laboratory consolidation of structured soils, are considered. For each problem, solution is obtained through integration of the equations governing the consolidation of the DP medium as well as via FEM applied to the ordered schemes composed of different materials. The presence of conventional experimental devices to ensure the drainage of the sample is taken into account through appropriate boundary conditions. Comparison of FEM results with theoretical results clearly points out the ability of the DP model to represent consolidation processes of structurally complex soils. Limits of applicability of the DP model may arise when the rate of fluid exchange between the two porous systems is represented through oversimplified relations. Results of computations, obtained having assigned reasonable values to the meso-structural and to the experimental apparatus parameters, point out that a partially efficient drainage apparatus strongly influences the distribution along the sample and the time evolution of the interstitial water pressure acting in both systems of pores. Data of consolidation tests in a Rowe's cell on samples of artificially fissured clays reported in the literature are compared with the analytical and numerical results showing a significant agreement.

  6. Evolution of mechanical characteristics and permeability of clayey materials under the influence of thermal loadings

    International Nuclear Information System (INIS)

    Boucly-Norotte, V.

    1991-01-01

    This research thesis reports the study of the effects on a long term of temperature variations on the volume and texture of clayey soils, notably with respect to their initial petro-physical and petro-graphical characteristics, and to their consolidation state. From an experimental point of view, this research is based on the monitoring of the volume strain and of the permeability of samples placed in an oedometric cell and submitted to thermal loadings within the 20 C - 110 C range. A thorough texture investigation (mercury-based porosimetry, observation by scanning electronic microscopy, and so on) before and after testing allows the evolution of material texture to be assessed [fr

  7. Formation of gaseous hydrogen induced by the effect of gamma rays on clayey materials

    International Nuclear Information System (INIS)

    Fattahi, M.; Grambow, B.; Houee-Levin, Ch.

    1999-01-01

    The irradiation (mainly gamma) of compact clayey materials, like those that would be used as engineered safety barriers for vitrified waste packages, can lead to hydrogen formation because of their water content. The radiolytic formation of gaseous hydrogen has been studied and the radiolytic efficiency of H 2 production with respect to the total initial mass of water in the clay is about 0.45 x 10 -7 mol.J -1 . This production is comparable to the one obtained at the primary stage of pure water radiolysis. (J.S.)

  8. Mineralogy and geochemistry of clayey dump materials from Troyanovo-2 mine, East Maritza Basin (Bulgaria)

    International Nuclear Information System (INIS)

    Milakovska, Z.; Goettlicher, J.; Gasharova, B.; Pohlmann-Lortz, M.

    2005-01-01

    Eleven samples of macroscopic different types of surface dump materials (black, gray-green and ochreous clays and clay mixtures) which were heaped during different stages of open-pit coal mining were studied. Montmorillonite ((Na,Ca) 0.33 (Al,Mg) 2 Si 4 O 10 (OH) 2 ), illite (K(Al, Mg, Fe) 2 AlSi 3 O 10 (OH) 2 ), calcite (CaCO 3 ), halloysite (Al 2 Si 2 O 5 (OH) 4 ), and less frequently kaolinite (Si 4 Al 4 O 10 (OH) 8 ) and quartz (SiO 2 ) are the main primary minerals identified. Primary sulfide minerals determined are pyrite (FeS 2 ) (detected in three samples) and arsenopyrite (FeAsS) - in two samples. Gypsum (CaSO 4 x2H 2 O) is the most widespread secondary mineral followed by goethite (FeOOH) and hematite (Fe 2 O 3 ). Na-rich jarosite (ideal: NaFe 3 (SO 4 ) 2 (OH) 6 ) was identified in two samples, lepidocrocite (γ-FeOOH) - only in one. One sample is free of secondary minerals. The mineralogical study shows that oxidation processes of the surface dump materials are not finished yet and pyrite is still present in samples stored 20 years ago. Main factors contributing to the slow rate of oxidation process are clay minerals, low sulfide content (prerequisite for a low oxidation potential), and calcite that contributes to the acidity neutralising potential of the clayey materials. (authors)

  9. Analysis of unsaturated clayey materials hydration incorporating the effect of thermo-osmotic flow

    International Nuclear Information System (INIS)

    Sanchez, M.; Arson, C.

    2012-01-01

    past, for example Soler (2001) studied the impact of coupled phenomena on the long-term behavior of radioactive waste repositories in saturated argillaceous rock. Bing (2006) proposed an analytical solution in the half-space for the thermal consolidation of layered saturated soils, including the influences of thermo-osmosis and thermal filtration. Chen et al. (2009) recently proposed a coupled Thermo-Hydro-Mechanical (THM) formulation which accounts for the flow of water and air driven by temperature gradients. The aim of this work is to explore the impact of thermo-osmosis on the hydration of clayey soils and rocks generally used in the design of nuclear waste disposals. Both small scale experiments and large scale problems are analyzed. A coupled THM formulation has been extended to deal with thermal osmosis in porous media. Special emphasis is put on the study of thermo-osmotic flow in unsaturated low permeability clays. A simple model was implemented in Theta-Stock program to study thermo-osmotic effects in the performance of a nuclear waste repository. The thermo-osmotic conductivity K fT is assumed to be a scalar (k T ). The permeability of the liquid phase in the initial state is around 5*10-13 m.s -1 . The thermo-osmotic coefficient k T is taken 100 times higher than the typical permeability of the massif: k T = 5*10 -11 m.s -1 . Containers are assumed to be stored in a 100- meter depth horizontal gallery. The ground water is located at 500 meters depth. The initial saturation degree of the ground mass was 0.15. The response of the unsaturated tuff is studied over 1000 years. The material parameters, related to fluid and temperature effects, are taken from the data given by Pollock (1986). Up to 200 years of heating, the trends of the saturation degree are the same in both models. But the magnitudes are different around the heating source, between 80 meters and 140 meters deep. With the model accounting for thermo-osmotic effects, the saturation degree is

  10. Creep consolidation of nuclear depository backfill materials

    International Nuclear Information System (INIS)

    Butcher, B.M.

    1980-10-01

    Evaluation of the effects of backfilling nuclear waste repository rooms is an important aspect of waste repository design. Consolidation of the porous backfill takes place as the room closes with time, causing the supporting stress exerted by the backfill against the intact rock to increase. Estimation of the rate of backfill consolidation is required for closure rate predictions and should be possible if the creep law for the solid constituent is known. A simple theory describing consolidation with a spherical void model is derived to illustrate this relationship. Although the present form of the theory assumes a homogeneous isotropic incompressible material atypical of most rocks, it may be applicable to rock salt, which exhibits considerable plasticity under confined pressure. Application of the theory is illustrated assuming a simple steady-state creep law, to show that the consolidation rate depends on the externally applied stress, temperature, and porosity

  11. The Ndop plain clayey materials (Bamenda area – NW Cameroon: Mineralogical, geochemical, physical characteristics and properties of their fired products

    Directory of Open Access Journals (Sweden)

    Rose Yongue-Fouateu

    2016-09-01

    Full Text Available The physicochemical, mineralogical and technological properties of clayey materials from the Ndop plain (NW Cameroon have been investigated, for their ceramic applications. The clayey materials have mixed facies with colour ranging from brown, grey, mottled and yellowish brown. The thickness of the exploitable clay layer is more than 5 m. Their mineralogical constituents are quartz, kaolinite, illite and feldspars, with kaolinite as major clay mineral. Based on the geochemistry, their source rocks might be felsic, with a mafic rock inference. These materials display high percentage in fine particles and high Atterberg limits. For all the firing temperatures, flexural strength (1.2–11 MPa, water absorption (8.03–24.27%, linear shrinkage (2.10%, weight loss (4.88–16.54% and bulk density (1.57–2.03 g/cm3 indicate good ceramic properties for firing samples between 900 and 1100 °C. Most of the fired test bricks show a brick red colour with good to very good cohesion. The studied clays were thus, suitable as raw materials for roof tiles, light weight blocks and hollow bricks; however, mixing of high clayey and highly silty materials could improve the quality of the products.

  12. Coupled transport in clayey materials with emphasis on induced electrokinetic phenomena

    NARCIS (Netherlands)

    Heister, Katja

    2005-01-01

    Movement of water and solutes in clay is important in groundwater and waste management, e.g. in seawater intrusion in near costal areas, in clay liners at disposal sites, in emissions from contaminated clayey sediments and sludges and in radioactive waste storage in clay formations. Dense clays act

  13. Probing Fe (III)/Fe (II) redox potential in a clayey material

    International Nuclear Information System (INIS)

    Tournassat, Christophe; Chainet, Fabien; Betelu, Stephanie; Hadi, Jebril; Gaucher, Eric C.; Ignatiadis, Ioannis; Greneche, Jean-Marc; Charlet, Laurent

    2010-01-01

    Document available in extended abstract form only. Redox is one of the main factors affecting the migration of redox-sensitive radionuclides. As a consequence reducing conditions are considered of strategic importance for the confinement properties of a clayey formation towards nuclear waste. A representative redox potential of clay formation such as Callovian- Oxfordian (COx) can be derived from thermodynamic calculations considering equilibrium between observed redox phases such as pyrite and siderite. However, there is little information on the reactivity of the different reservoirs of redox constituents in this type of complex material. The present study aims at investigating the reactivity of the Fe(III)/Fe(II) redox couple in the structure of clay minerals using different investigation methods: electrochemistry and O 2 reduction kinetic experiments. Clay modified electrodes were specifically designed to probe Fe(III)/Fe(II) redox potential in the structure of clay minerals. The clay fraction of a Callovian-Oxfordian argillite sample originating from the same level than ANDRA underground research laboratory was used after pre-treatment to remove organic matter and accessory minerals such as pyrite that could influence redox potential measurements. These electrodes were used to verify the validity of the model of Favre et al. (2006) that links the redox potential (E clay ) to the the Fe(II)/Fe tot ratio in the structure (m rel ), the pH and the sodium concentration in solution: equation 1. The good agreement between direct potential measurements and model prediction provides a strong evidence of the relevance of this model in our experimental conditions although the clay composition and its too low Fe content do not a priori fulfil the conditions set by Drits and Manceau (2000) for the calculation of K 0 parameter. Following the verification of the model, we tried to apply it to the specific case of a Callovian-Oxfordian sample that had been very well preserved

  14. A contribution to the physical and chemical model of long-lived radioactive wastes by clayey materials

    International Nuclear Information System (INIS)

    Gorgeon, L.

    1994-01-01

    This work deals with the high-level and long-lived radioactive wastes confinement which come from the irradiated fuels reprocessing. These wastes are generally coated in a deep geological structure confinement matrix. The radiation protection of a such storage requires that the coating matrix, the technological barriers which separate the storage and the geological medium and the reception rock does not let the radioactive wastes pass. The materials used in this work for the confinement studies are clayey minerals and the retention mechanisms studies are realized on cesium 135, neptunium 237, americium 241 and uranium 233. The first part of this thesis concerns the clayey minerals retention properties towards ions in aqueous solutions. More particularly the relations between these properties and the chemical structure of these solids are investigated. In the second part are presented the experimental works which have allowed to specify the intrinsic characteristics of the studied minerals. Indeed the knowledge of these parameters is essential to quantitatively explain the results of the radionuclides retention. The adsorption mechanisms are described in a third part. (O.L.). 112 refs., 59 figs., 51 tabs

  15. New quantitative methods for mineral and porosity mapping in clayey materials: application to the compacted bentonites of engineered barriers

    International Nuclear Information System (INIS)

    Pret, D.

    2003-12-01

    Clayey materials are well known for their non permeable properties and their textural changes between the dry and hydrated states. Their porous network is classically investigated in the dry state using bulk measurements. However, the relationship between porosity and mineral spatial heterogeneities in the hydrated state is poorly understood. The textural analysis limits induce some difficulties to understand the migration of solute species into compacted bentonites (as for nuclear waste repository). The goal of this work is to improve the analysis techniques for hydrated clayey materials in order to provide a multi-scale quantitative petrography. The bentonite samples are impregnated using a resin whose properties are close to water ones. The classical petrographic study reveals strong heterogeneities of spatial and size distributions of porosity and minerals. SEM images analysis allows a quantification and a simple mapping of pores and minerals into unaltered bentonites. Nevertheless, as alterations are suspected to happen in the repository context, two methods for the analysis of all types of materials have been also developed. Two specific softwares permits the treatments of autoradiographs and chemical element maps obtained using electron microprobe. The results are quantitative maps highlighting the spatial porosity heterogeneities from the decimetric to the micrometric scales. All pore sizes are taken into account including clay interlayer spaces. Moreover, an accurate mineral mapping is also supplied on millimetric areas with a spatial resolution close to the micrometer. In a widely point of view, this work provides new complementary tools for the textural analysis of fine grained materials and the improvement of migration modelling of solute species. (author)

  16. An improved electrokinetic method to consolidate porous materials

    DEFF Research Database (Denmark)

    Feijoo, Jorge; Ottosen, Lisbeth M.; Nóvoa, X. R.

    2017-01-01

    the consolidation using commercial products have some limitations, such as: (1) low penetrability; (2) no chemical and mineralogical affinity with the material to treat and (3) release of toxic compounds (VOCs), during the solvent evaporation. In the last years, a new consolidation method based on electrokinetic...... the pH of the solutions in contact with the porous material, which can damage it and (2) it is difficult to determine in which area the consolidation takes place. In this study an electrokinetic consolidation method, which has two steps between which the current is reversed, is proposed to solve all...... techniques was developed. This method allows filling some pores by the precipitation of an inorganic compound. As a result the method allows increasing the penetration depth of current consolidation treatments. However, this method needs to be improved since: (1) no special care is taking in controlling...

  17. Moessbauer spectroscopy and X-ray diffraction analyses of clayey samples used as ceramic sourcing materials, in Peru

    Energy Technology Data Exchange (ETDEWEB)

    Quille, Ruben, E-mail: quilleruben@gmail.com; Bustamante, Angel [San Marcos National University, Laboratory of Ceramics and Nanomaterials, Faculty of Physical Sciences (Peru); Palomino, Ybar [National University of San Cristobal de Huamanga, Experimental Center of Ceramics (Peru)

    2011-11-15

    The ceramic industry is an important area of economic activity in the Ayacucho Region, in particular in the District of Quinua. As a consequence, there is a huge demand for clay to produce ceramic pastes in that region. This paper reports on results concerning the mineralogical characterization of four clayey samples, which were collected MAA and SPQA from the area Pampa de La Quinua with geographic coordinates 13 Degree-Sign 02 Prime 49 Double-Prime S 74 Degree-Sign 08 Prime 03 Double-Prime W, CE1M and CE2M from the Quinua locality 13 Degree-Sign 03 Prime 07 Double-Prime S 74 Degree-Sign 08 Prime 31 Double-Prime W, both in the District of Quinua, Province of Huamanga, Ayacucho, Peru. The chemical and mineralogical characterization of these samples was carried out with powder X-ray diffraction detecting quartz, albite, montmorillonite, kaolinite and glauconite mineral phases, Moessbauer spectroscopy detected iron in kaolinite, glauconite and montmorillonite minerals. Chemical analysis was performed through scanning electron microscopy and energy dispersive X-ray spectroscopy. Data obtained from the combination of these techniques provided relevant information about the morphology, chemical composition, and the mineralogy of samples.

  18. Mössbauer spectroscopy and X-ray diffraction analyses of clayey samples used as ceramic sourcing materials, in Peru

    Science.gov (United States)

    Quille, Rubén; Bustamante, Ángel; Palomino, Ybar

    2011-11-01

    The ceramic industry is an important area of economic activity in the Ayacucho Region, in particular in the District of Quinua. As a consequence, there is a huge demand for clay to produce ceramic pastes in that region. This paper reports on results concerning the mineralogical characterization of four clayey samples, which were collected MAA and SPQA from the area Pampa de La Quinua with geographic coordinates 13° 02' 49″ S 74° 08' 03″ W, CE1M and CE2M from the Quinua locality 13° 03' 07″ S 74° 08' 31″ W, both in the District of Quinua, Province of Huamanga, Ayacucho, Peru. The chemical and mineralogical characterization of these samples was carried out with powder X-ray diffraction detecting quartz, albite, montmorillonite, kaolinite and glauconite mineral phases, Mössbauer spectroscopy detected iron in kaolinite, glauconite and montmorillonite minerals. Chemical analysis was performed through scanning electron microscopy and energy dispersive X-ray spectroscopy. Data obtained from the combination of these techniques provided relevant information about the morphology, chemical composition, and the mineralogy of samples.

  19. Mössbauer spectroscopy and X-ray diffraction analyses of clayey samples used as ceramic sourcing materials, in Peru

    International Nuclear Information System (INIS)

    Quille, Rubén; Bustamante, Ángel; Palomino, Ybar

    2011-01-01

    The ceramic industry is an important area of economic activity in the Ayacucho Region, in particular in the District of Quinua. As a consequence, there is a huge demand for clay to produce ceramic pastes in that region. This paper reports on results concerning the mineralogical characterization of four clayey samples, which were collected MAA and SPQA from the area Pampa de La Quinua with geographic coordinates 13° 02′ 49″ S 74° 08′ 03″ W, CE1M and CE2M from the Quinua locality 13° 03′ 07″ S 74° 08′ 31″ W, both in the District of Quinua, Province of Huamanga, Ayacucho, Peru. The chemical and mineralogical characterization of these samples was carried out with powder X-ray diffraction detecting quartz, albite, montmorillonite, kaolinite and glauconite mineral phases, Mössbauer spectroscopy detected iron in kaolinite, glauconite and montmorillonite minerals. Chemical analysis was performed through scanning electron microscopy and energy dispersive X-ray spectroscopy. Data obtained from the combination of these techniques provided relevant information about the morphology, chemical composition, and the mineralogy of samples.

  20. Simulation of consolidation in partially saturated soil materials

    International Nuclear Information System (INIS)

    Narasimhan, T.N.

    1982-03-01

    Partially saturated soil materials undergo consolidation, heave, collapse and failure due to changes in pore fluid pressure. The precise nature of the mechanics of such deformations is only poorly understood at present. Experimental evidence has shown that the volume change behavior of unsaturated soils cannot be adequately explained through changes in effective stress, even when a saturation dependent parameter is incorporated into the definition of effective stress. Two independent stress-state variables, involving combinations of total stress, pore air pressure and pore water pressure, are required to characterize volume changes and saturation changes in the partially saturated state. In general, two coupled conservation equations, one for the water-phase and the other for the air-phase need to be solved in order to predict the deformation behavior of unsaturated soils. If directional displacements and changes in the stress-field are required, then the conservation equations are to be integrated with an additional set of multi-dimensional force balance equations. For lack of a sufficient understanding of elastic constants such as Poisson's Ratio and Lame's constants as applied to unsaturated soils, little has been achieved so far in integrating the conservation equations and the force balance equations. For the long-term modeling of consolidation with respect to uranium mill tailings, it may be acceptable and economical to solve a single conservation equation for water, assuming that the air-phase is continuous and is at atmospheric pressure everywhere in the soil. The greatest challenge to modeling consolidation in the unsaturated zone at the presnt time is to develop enough experimental data defining the variation of void ratio and saturation with reference to the two chosen stress-state variables

  1. Tests with ceramic waste form materials made by pressureless consolidation

    International Nuclear Information System (INIS)

    Lewis, M. A.; Hash, M. C.; Hebden, A. S.; Ebert, W. L.

    2002-01-01

    A multiphase waste form referred to as the ceramic waste form (CWF) will be used to immobilize radioactively contaminated salt wastes recovered after the electrometallurgical treatment of spent sodium-bonded nuclear fuel. The CWF is made by first occluding salt in zeolite and then encapsulating the zeolite in a borosilicate binder glass. A variety of surrogate CWF materials were made using pressureless consolidation (PC) methods for comparison with CWF consolidated using a hot isostatic press (HIP) method and to study the effects of glass/zeolite batching ratio and processing conditions on the physical and chemical properties of the resulting materials. The data summarized in this report will also be used to support qualification of the PC CWF for disposal in the proposed federal high-level radioactive waste repository at Yucca Mountain. The phase composition and microstructure of HIP CWF and PC CWF are essentially identical: both are composed of about 70% sodalite, 25% binder glass, and a 5% total of inclusion phases (halite, nepheline, and various oxides and silicates). The primary difference is that PC CWF materials have higher porosities than HIP CWFs. The product consistency test (PCT) that was initially developed to monitor homogeneous glass waste forms was used to measure the chemical durabilities of the CWF materials. Series of replicate tests with several PC CWF materials indicate that the PCT can be conducted with the same precision with CWF materials as with borosilicate glasses. Short-term (7-day) PCTs were used to evaluate the repeatability of making the PC CWF and the effects of the glass/zeolite mass ratio, process temperature, and processing time on the chemical durability. Long-term (up to 1 year) PCTs were used to compare the durabilities of HIP and PC CWFs and to estimate the apparent solubility limit for the PC CWF that is needed for modeling. The PC and HIP CWF materials had similar disabilities, based on the release of silicon in long

  2. Physicochemical characteristics of geophagic clayey soils from ...

    African Journals Online (AJOL)

    ONOS

    2010-09-06

    Sep 6, 2010 ... INTRODUCTION. The contamination of food with soil and clay materials .... These properties may dictate the inter-reactions between the ingested soil ... significant difference in the wt % of silt in geophagic .... Preference for these clayey ..... size on the flocculation behaviour of ultra-fine clays in salt solutions.

  3. Nanocomposite Thermolectric Materials by High Pressure Powder Consolidation Manufacturing, Phase I

    Data.gov (United States)

    National Aeronautics and Space Administration — In response to NASA's need to develop advanced nanostructured thermolectric materials, UTRON is proposing an innovative high pressure powder consolidation...

  4. Nanocomposite Thermolectric Materials by High Pressure Powder Consolidation Manufacturing, Phase II

    Data.gov (United States)

    National Aeronautics and Space Administration — In response to NASA's need to develop advanced nanostructured thermolectric materials, UTRON is proposing an innovative high pressure powder consolidation...

  5. Summary of the 1. Annual Workshop Topical Session on 'Diffusion and Retention in Compacted Clayey Materials'

    Energy Technology Data Exchange (ETDEWEB)

    Altmann, Scott [Andra - Agence Nationale pour la gestion des Dechets Radioac tifs, F-92298 Chatenary Malabry CEDEX (France)]. e-mail: Scott.altmann@andra.fr

    2007-06-15

    The main objective of this topical session was to provide an overview of the diversity of conceptual and experimental approaches which are being used to further our understanding of a key process for radwaste management: coupled 'diffusion - sorption' transport of radionuclides in compacted clay-rich materials (clayrock, bentonite). The introductory presentation by Eric Giffaut (Andra) entitled 'General conceptual framework for solute transport through compacted clays and frequent observations in diffusion studies' provided a framework for the other talks. The commonly used means for characterizing steady state diffusion (e.g. through diffusion for determining D{sub e}) and 'equilibrium' retention parameters (solid-solution partitioning in batch systems), as a function of key state parameters (aqueous phase composition, compaction density, sorbing element concentration), on relatively small rock volumes/masses were mentioned. It was pointed out that, despite the significant existing databases of results from such measurements, various uncertainties remain which need to be reduced in order to increase confidence in safety cases. The most direct approach to determining the transport parameters needed for performance assessment models (e.g. apparent diffusion coefficient, retardation factor, accessible porosity) is to carry out direct measurements via migration experiments, and then to extract the parameter values by interpreting data with an appropriate model. This approach is the foundation for much of the program carried out by SCK.CEN for characterizing the Boom clay. The talk by Norbert Maes (SCK-CEN) entitled 'Experimental research on diffusion in natural clay samples. An overview of the Belgian experience' illustrated how these type studies were carried out using different techniques applied to a variety of radionuclides in order both to understand migration mechanisms and to determine PA parameters representative of in

  6. Geomechanical properties of lime stabilized clayey sands

    International Nuclear Information System (INIS)

    Arabani, M.; Karami, M. Veis

    2007-01-01

    Clayey sands that have low plasticity, low compressibility and high strength under loads, are suitable as a base material for any engineering construction projects as well as for roads and building construction. Decrease of plasticity and compressibility as well as increase in strength of these materials can be obtained by many different methods. Of these methods, lime stabilization is a common, applicable, and easy to use approach that can improve geomechanical and geotechnical properties of clayey sand fills. In this study some important geomechanical properties and geotechnical properties of clayey sands including compressive strength, CBR and elastic plastic behavior are investigated. A range of gradations representative of those gradations found in situ in the north of Iran were selected for testing and samples were artificially rebuilt in the laboratory. The mixes were then stabilized with hydrated lime and cured. Different mechanical tests were performed on mature materials. The stress-strain behavior of lime-stabilized mixes was plotted and a parabolic function was used to estimate the trend of stress-strain behavior. The data show that there is a correlation among the results of uniaxial load test, tensile strength, and CBR of the tested specimens. Also, results of the unconfined compression test and the indirect tensile strength test show that an increase in clay content up to a certain percent, in the clay-sand fills, tends to increase the strength of the materials in compression as well as in tension. (author)

  7. Improvement of Characteristics of Clayey Soil Mixed with Randomly Distributed Natural Fibers

    Science.gov (United States)

    Maity, J.; Chattopadhyay, B. C.; Mukherjee, S. P.

    2017-11-01

    In subgrade construction for flexible road pavement, properties of clayey soils available locally can be improved by providing randomly distributed fibers in the soil. The fibers added in subgrade constructions are expected to provide better compact interlocking system between the fiber and the soil grain, greater resistance to deformation and quicker dissipation of pore water pressure, thus helping consolidation and strengthening. Many natural fibers like jute, coir, sabai grass etc. which are economical and eco-friendly, are grown in abundance in India. If suitable they can be used as additive material in the subgrade soil to result in increase in strength and decrease in deformability. Such application will also reduce the cost of construction of roads, by providing lesser thickness of pavement layer. In this paper, the efficacy of using natural jute, coir or sabai grass fibers with locally available clayey soil has been studied. A series of Standard Proctor test, Soaked and Unsoaked California Bearing Ratio (CBR) test, and Unconfined Compressive Strength test were done on locally available clayey soil mixed with different types of natural fiber for various length and proportion to study the improvement of strength properties of fiber-soil composites placed at optimum moisture content. From the test results, it was observed that there was a substantial increase in CBR value for the clayey soil when mixed with increasing percentage of all three types of randomly distributed natural fibers up to 2% of the dry weight of soil. The CBR attains maximum value when the length for all types of fibers mixed with the clay taken in this study, attains a value of 10 mm.

  8. Alkaline plume on clayey materials

    International Nuclear Information System (INIS)

    Marsal, Francois; Pellegrini, Delphine; De Windt, Laurent

    2012-01-01

    Francois Marsal from IRSN, France, gave an overview of the interactions between concrete and clays. His presentation focused on safety issues related to the concrete tunnel seals designed in France for the disposal of intermediate-level long-lived waste and related to the tunnel plugs for HLW disposal. In the study described, three main effects were identified that need to be addressed: - Changes in mineralogy and pore water chemistry. - The intensity and extent of the perturbations. - The consequences in terms of changes in the chemical and hydraulic containment capacities of the repository system. Addressing these questions requires a combination of laboratory experiments, engineered and natural analogue studies, and modelling of the long-term evolution of these systems. Several laboratory results were presented. Among the engineered analogues, results from Tournemire were described. Numerical modelling is the only available tool that can tackle the spatial and temporal perturbations at a repository scale. There are still quite a number of uncertainties concerning the modelling of the mineralogical evolution of the clay in contact with cement pore waters. Furthermore, the hydraulic properties are still difficult to assess, for example the extent of clogging and the influence of heterogeneities

  9. Experimental Studies on Earthen Architecture Sites Consolidated with BS Materials in Arid Regions

    Directory of Open Access Journals (Sweden)

    Dong Zhao

    2016-01-01

    Full Text Available This paper takes the preservation works on the archaeological sites of Gaochang Ruins, Xinjiang, as background. Based on the soil characteristics analysis on the archaeological sites, experimental studies were conducted on the consolidation effect of the BS-10 consolidation material on the archaeological sites of adobe and rammed earth. The results showed the following:, after consolidation, the wind erosion resistance of the soil on the archaeological sites was substantially increased, and the wind erosion modulus was reduced by 5~8 times; the soil exhibited fine grid structure and significantly reduced degree of permeability, while still maintaining the moisture exchange between inside and outside the soil; there is excellent ageing resistance; the resistance to freezing and thawing was closely related to the soil water content and had little influence in arid regions; the water resistance was improved and could satisfy the requirements for consolidating the sites in arid regions; the unconfined compressive strength was improved moderately, which was the key direction of improvement in the future, and the consolidated soil did not form duricrust on the surface and had good bonding strength with the internal parts. The BS-10 material can meet the consolidation requirements for the earthen archaeological sites in arid regions of northwest China.

  10. Leachability of Ra-226 from uranium mill tailings consolidated with naturally occuring materials and/or cement. Pt. 2

    International Nuclear Information System (INIS)

    Nathwani, J.S.; Phillips, C.R.

    1980-01-01

    The leaching of Ra-226 from U mill tailings consolidated with cement and cement plus clay and/or peat may be described by a plane source diffusion model or a simultaneous first order reaction and diffusion model. A useful quantitative measure of the effectiveness of the consolidation process is the magnitude of the effective diffusion coefficient relative to that of the unconsolidated tailings material. The lowest effective diffusion coefficient upon consolidation was for consolidation with cement and peat. (orig.)

  11. A contribution to the physical and chemical model of long-lived radioactive wastes by clayey materials; Contribution a la modelisation physico-chimique de la retention de radioelements a vie longue par des materiaux argileux

    Energy Technology Data Exchange (ETDEWEB)

    Gorgeon, L

    1994-11-25

    This work deals with the high-level and long-lived radioactive wastes confinement which come from the irradiated fuels reprocessing. These wastes are generally coated in a deep geological structure confinement matrix. The radiation protection of a such storage requires that the coating matrix, the technological barriers which separate the storage and the geological medium and the reception rock does not let the radioactive wastes pass. The materials used in this work for the confinement studies are clayey minerals and the retention mechanisms studies are realized on cesium 135, neptunium 237, americium 241 and uranium 233. The first part of this thesis concerns the clayey minerals retention properties towards ions in aqueous solutions. More particularly the relations between these properties and the chemical structure of these solids are investigated. In the second part are presented the experimental works which have allowed to specify the intrinsic characteristics of the studied minerals. Indeed the knowledge of these parameters is essential to quantitatively explain the results of the radionuclides retention. The adsorption mechanisms are described in a third part. (O.L.). 112 refs., 59 figs., 51 tabs.

  12. ELECTROKINETIC DEVICE AND METHOD FOR CONSOLIDATING POROUS MATERIALS

    DEFF Research Database (Denmark)

    2017-01-01

    The invention relates to a device and an associated electrokinetic method which allows the pores (superficial and deep) of a porous material to be filled, by forcing the precipitation therein of a product of low solubility in water by creating an electric field which will mobilise the cations...... and anions supplied by previously selected solutions. This method comprises two phases. In the first phase, the pores located at a specified distance from the surface of contact between the porous material and the anodic or cathodic compartment are plugged. In a second phase, the rest of the pores, mainly...... those which are on the surface level, are collapsed. As a result of the designed device and the plugging system contained therein, the porous material is not affected at any moment by chemical alteration processes caused by contact with extreme pH values. This device allows the treatment to be applied...

  13. Development of functionally graded materials by ultrasonic consolidation

    CSIR Research Space (South Africa)

    Kumar, S

    2010-08-01

    Full Text Available parameters for welding various combinations of materials have been found for making a sample of aminimumo f62 foils of width 2” and length 3”. Optical microscopy and mirohardness test have been performed thereupon for the characterization....

  14. Dematerialization of the Ruins : Glass as a Promising Restorative Material for the Consolidation of Historic Structures

    NARCIS (Netherlands)

    Barou, L.; Oikonomopoulou, F.; Bristogianni, T.; Veer, F.A.; Nijsse, R.; Louter, Christian; Bos, Freek; Belis, Jan; Veer, Fred; Nijsse, Rob

    This research investigates the potential of glass as a new design tool to highlight and safeguard our historic structures. Current restoration and conservation treatments with traditional materials bear the risk of conjecture between the original and new elements, whereas the high consolidation

  15. Feasibility study on consolidation of Fernald Environmental Management Project depleted uranium materials

    International Nuclear Information System (INIS)

    1995-01-01

    In 1991, the DOE made a decision to close the FMPC located in Fernald, Ohio, and end its production mission. The site was renamed FEMP to reflect Fernald's mission change from uranium production to environmental restoration. As a result of this change, the inventory of strategic uranium materials maintained at Fernald by DOE DP will need to be relocated to other DOE sites. Although considered a liability to the Fernald Plant due to its current D and D mission, the FEMP DU represents a potentially valuable DOE resource. Recognizing its value, it may be important for the DOE to consolidate the material at one site and place it in a safe long-term storage condition until a future DOE programmatic requirement materializes. In August 1995, the DOE Office of Nuclear Weapons Management requested, Lockheed Martin Energy Systems (LMES) to assess the feasibility of consolidating the FEMP DU materials at the Oak Ridge Reservation (ORR). This feasibility study examines various phases associated with the consolidation of the FEMP DU at the ORR. If useful short-term applications for the DU fail to materialize, then long-term storage (up to 50 years) would need to be provided. Phases examined in this report include DU material value; potential uses; sampling; packaging and transportation; material control and accountability; environmental, health and safety issues; storage; project management; noneconomic factors; schedule; and cost

  16. Colloid and materials science for the conservation of cultural heritage: cleaning, consolidation, and deacidification.

    Science.gov (United States)

    Baglioni, Piero; Chelazzi, David; Giorgi, Rodorico; Poggi, Giovanna

    2013-04-30

    Serendipity and experiment have been a frequent approach for the development of materials and methodologies used for a long time for either cleaning or consolidation of works of art. Recently, new perspectives have been opened by the application of materials science, colloid science, and interface science frameworks to conservation, generating a breakthrough in the development of innovative tools for the conservation and preservation of cultural heritage. This Article is an overview of the most recent contributions of colloid and materials science to the art conservation field, mainly focusing on the use of amphiphile-based fluids, gels, and alkaline earth metal hydroxide nanoparticles dispersions for the cleaning of pictorial surfaces, the consolidation of artistic substrates, and the deacidification of paper, canvas, and wood. Future possible directions for solving several conservation issues that still need to be faced are also highlighted.

  17. Electrochemical stabilization of clayey ground

    Science.gov (United States)

    Rzhanitzin, B.A.; Sokoloff, V.P.

    1947-01-01

    Recently developed new methods of stabilization of weak grounds (e.g. the silicate treatment) are based on injection of chemical solutions into the ground. Such methods are applicable accordingly only to the kinds of ground that have the coefficient of filtration higher than 2 meters per 24 hours and permit penetration of the chemical solutions under pressure. This limit, however, as it is shown by our experience in construction, excludes a numerous and an important class of grounds, stabilization of which is indispensable in many instances. For example, digging of trenches and pits in clayey, silty, or sandy ground shows that all these types act like typical "floaters" (sluds? -S) in the presence of the ground water pressure. There were several instances in the canalization of the city of Moskow where the laying of trenches below the ground water level has led to extreme difficulties with clayey and silty ground. Similar examples could be cited in mining, engineering hydrology, and railroad construction. For these reasons, the development of methods of stabilizing such difficult types of ground has become an urgent problem of our day. In 1936, the author began his investigations, at the ground Stabilization Laboratory of VODGEO Institute, with direct electrical current as the means of stabilization of grounds. Experiments had shown that a large number of clayey types, following passage of direct electrical current, undergoes a transformation of its physico-chemical properties. It was established that the (apparent -S) density of the ground is substantially increased in consequence of the application of direct electrical current. The ground loses also its capacity to swell and to soften in water. Later, after a more detailed study of the physico-chemical mechanism of the electrical stabilization, it became possible to develop the method so as to make it applicable to sandy and silty as well as to clayey ground. By this time (1941, S.), the method has already been

  18. Effect of various supplementary cementitious materials on rheological properties of self-consolidating concrete

    OpenAIRE

    Saleh Ahari, Reza; Erdem, Tahir Kemal; Ramyar, Kambiz

    2015-01-01

    In design of self-consolidating concrete (SCC) for a given application, the mixture's rheological parameters should be adjusted to achieve a given profile of yield stress and plastic viscosity. Supplementary cementitious materials (SCM) can be useful for this adjustment in addition to their other advantages. In this study, the rheological properties of 57 SCC mixtures with various SCM were investigated for a constant slump flow value. For this aim, various amounts of silica fume (SF), metakao...

  19. Influence of Fines Content on Consolidation and Compressibility Characteristics of Granular Materials

    Science.gov (United States)

    Lipiński, Mirosław J.; Wdowska, Małgorzata K.; Jaroń, Łukasz

    2017-10-01

    Various behaviour of soil under loading results to large extent from kind of soil considered. There is a lot of literature concerning pure sand or plastic clays, while little is known about materials, which are from classification point of view, between those soils. These materials can be considered as cohesionless soils with various fines content. The paper present results of tests carried out in large consolidometer on three kinds of soil, containing 10, 36 and 97% of fines content. Consolidation, permeability and compressibility characteristics were determined. Analysis of the test results allowed to formulate conclusion concerning change in soil behaviour resulting from fines content.

  20. Towards a more consolidated approach to material data management in life assessment of power plant components

    Energy Technology Data Exchange (ETDEWEB)

    Jovanovic, A.; Maile, K. [MPA Stuttgart (Germany)

    1998-12-31

    The presentation discusses the necessity of having a more consolidated (unified, possibly `European`) framework for all (not only pure experimental) material data needed for optimized life management and assessment of high-temperature and other components in power and process plants. After setting the main requirements for such a system, a description of efforts done in this direction at MPA Stuttgart in the area of high-temperature components in power plants is given. Furthermore, a reference to other relevant efforts elsewhere is made and an example of practical application of the proposed solution described (optimized material selection and life assessment of high-temperature piping). (orig.) 10 refs.

  1. Towards a more consolidated approach to material data management in life assessment of power plant components

    Energy Technology Data Exchange (ETDEWEB)

    Jovanovic, A; Maile, K [MPA Stuttgart (Germany)

    1999-12-31

    The presentation discusses the necessity of having a more consolidated (unified, possibly `European`) framework for all (not only pure experimental) material data needed for optimized life management and assessment of high-temperature and other components in power and process plants. After setting the main requirements for such a system, a description of efforts done in this direction at MPA Stuttgart in the area of high-temperature components in power plants is given. Furthermore, a reference to other relevant efforts elsewhere is made and an example of practical application of the proposed solution described (optimized material selection and life assessment of high-temperature piping). (orig.) 10 refs.

  2. Study of Material Consolidation at Higher Throughput Parameters in Selective Laser Melting of Inconel 718

    Science.gov (United States)

    Prater, Tracie

    2016-01-01

    Selective Laser Melting (SLM) is a powder bed fusion additive manufacturing process used increasingly in the aerospace industry to reduce the cost, weight, and fabrication time for complex propulsion components. SLM stands poised to revolutionize propulsion manufacturing, but there are a number of technical questions that must be addressed in order to achieve rapid, efficient fabrication and ensure adequate performance of parts manufactured using this process in safety-critical flight applications. Previous optimization studies for SLM using the Concept Laser M1 and M2 machines at NASA Marshall Space Flight Center have centered on machine default parameters. The objective of this work is to characterize the impact of higher throughput parameters (a previously unexplored region of the manufacturing operating envelope for this application) on material consolidation. In phase I of this work, density blocks were analyzed to explore the relationship between build parameters (laser power, scan speed, hatch spacing, and layer thickness) and material consolidation (assessed in terms of as-built density and porosity). Phase II additionally considers the impact of post-processing, specifically hot isostatic pressing and heat treatment, as well as deposition pattern on material consolidation in the same higher energy parameter regime considered in the phase I work. Density and microstructure represent the "first-gate" metrics for determining the adequacy of the SLM process in this parameter range and, as a critical initial indicator of material quality, will factor into a follow-on DOE that assesses the impact of these parameters on mechanical properties. This work will contribute to creating a knowledge base (understanding material behavior in all ranges of the AM equipment operating envelope) that is critical to transitioning AM from the custom low rate production sphere it currently occupies to the world of mass high rate production, where parts are fabricated at a rapid

  3. Radioactive materials and waste. Planning Act of 28 June 2006. Consolidated version established by Andra

    International Nuclear Information System (INIS)

    2013-07-01

    This document is the English translation of the Articles of the Planning Act No. 2006-739 of 28 June 2006 and of the articles L. 542-1 and following of the Environmental Code (as modified) concerning the Sustainable Management of Radioactive Materials and Waste. This translation is provided for convenience purposes only, the French version remaining the only valid and legally-binding version. In order to enhance readability, all articles relating to Andra's activities are consolidated in this self-supporting document

  4. Impacts on health and safety from transfer/consolidation of nuclear materials and hazardous chemicals

    International Nuclear Information System (INIS)

    Gallucci, R.H.V.

    1994-11-01

    Environmental restoration plans at the US Department of Energy (USDOE) Hanford Site calls for transfer/consolidation of ''targets/threats,'' namely nuclear materials and hazardous chemicals. Reductions in the health and safety hazards will depend on the plans implemented. Pacific Northwest Laboratory (PNL) estimated these potential impacts, assuming implementation of the current reference plan and employing ongoing risk and safety analyses. The results indicated the potential for ''significant'' reductions in health and safety hazards in the long term (> 25 years) and a potentially ''noteworthy'' reduction in health hazard in the short term (≤ 25 years)

  5. Consolidation of Hierarchy-Structured Nanopowder Agglomerates and Its Application to Net-Shaping Nanopowder Materials

    Science.gov (United States)

    Lee, Jai-Sung; Choi, Joon-Phil; Lee, Geon-Yong

    2013-01-01

    This paper provides an overview on our recent investigations on the consolidation of hierarchy-structured nanopowder agglomerates and related applications to net-shaping nanopowder materials. Understanding the nanopowder agglomerate sintering (NAS) process is essential to processing of net-shaped nanopowder materials and components with small and complex shape. The key concept of the NAS process is to enhance material transport through controlling the powder interface volume of nanopowder agglomerates. Based upon this concept, we have suggested a new idea of full density processing for fabricating micro-powder injection molded part using metal nanopowder agglomerates produced by hydrogen reduction of metal oxide powders. Studies on the full density sintering of die compacted- and powder injection molded iron base nano-agglomerate powders are introduced and discussed in terms of densification process and microstructure. PMID:28788317

  6. Consolidation of Hierarchy-Structured Nanopowder Agglomerates and Its Application to Net-Shaping Nanopowder Materials

    Directory of Open Access Journals (Sweden)

    Geon-Yong Lee

    2013-09-01

    Full Text Available This paper provides an overview on our recent investigations on the consolidation of hierarchy-structured nanopowder agglomerates and related applications to net-shaping nanopowder materials. Understanding the nanopowder agglomerate sintering (NAS process is essential to processing of net-shaped nanopowder materials and components with small and complex shape. The key concept of the NAS process is to enhance material transport through controlling the powder interface volume of nanopowder agglomerates. Based upon this concept, we have suggested a new idea of full density processing for fabricating micro-powder injection molded part using metal nanopowder agglomerates produced by hydrogen reduction of metal oxide powders. Studies on the full density sintering of die compacted- and powder injection molded iron base nano-agglomerate powders are introduced and discussed in terms of densification process and microstructure.

  7. Physicochemical characteristics of geophagic clayey soils from ...

    African Journals Online (AJOL)

    ONOS

    2010-09-06

    Sep 6, 2010 ... 3School of Health Technology, Central University of Technology, Bloemfontein, Free State, Private Bag X20539. Bloemfontein 9300 .... Table 1. The collected clayey soil samples were air-dried and their physicochemical ...

  8. Hydric transfer in swelling clayey soils: influence of confinement

    International Nuclear Information System (INIS)

    Rolland, S.

    2002-01-01

    Description of imbibition and swelling mechanisms in clayey soils represents an important stake in different scientific domains such as agronomy, geotechnics or petroleum industry. The aim of the present work is to show the effects of hydro-mechanical couplings during imbibition in a swelling clayey medium, under different confinement conditions. Our material is a bentonite-silt mixture, prepared with a known water content and compacted with a double-piston technique. This method allows us to produce uniform soil samples, in terms of humidity and bulk density. Experiments related to bottom imbibition are then carried out for three types of mechanical boundary conditions (free, oedometric, fixed volume). The non-intrusive dual-energy gamma-ray technique is used to assess the local variation of bulk density and humidity. Finally, the three imbibition kinetics are compared for each experiment in terms of hydraulic diffusivity, described in a Lagrangian way. (author)

  9. Contribution to the study of cementitious and clayey materials behaviour in the context of deep geological disposal: transport aspect, durability and thermo-hydro-mechanical behaviour

    International Nuclear Information System (INIS)

    Galle, C.

    2011-07-01

    Deep geological formation disposal is the reference solution in France for the management of medium and high activities radioactive waste. In this context, to demonstrate the feasibility of such a disposal, it is necessary to evaluate the long-term performances and the behaviour of the materials engaged in the elaboration of engineered barrier systems (EBS) and waste package elements. The studies mentioned and synthesized in this HDR thesis focused mainly on the convective transport of gas (under pressure gradient) in cementitious matrices, by coupling microstructure aspect (porosity/pores sizes distribution) and hydric environment (water saturation). Works on physico-chemical durability allowed the description of the chemical degradation of cement-based materials in extreme conditions using ammonium nitrate, to increase the materials damaging processes in order to identify functional margins. In relationship with the interim storage management phase, studies related to the behaviour and characterization of concrete submitted to high temperatures (up to 400 C) were also described. Finally, results concerning the gas (H 2 ) overpressure resistance of engineered barriers made of compacted clays were summarized. (author)

  10. Effect of Lime on characteristics of consolidation, strength, swelling and plasticity of fine grained soil

    Science.gov (United States)

    Estabragh, A. R.; Bordbar, A. T.; Parsaee, B.; Eskandari, Gh.

    2009-04-01

    Using Lime as an additive material to clayey soil is one of the best effective technique in building the soil structures to get some purposes such as soil stabilization, soil reinforcement and decreasing soil swelling. In this research the effect of Lime on geotechnical characteristics of a clayey soil was investigated. Soil specimen types used in this study were consisted of clayey soil as the control treatment and clay mixed with different weight fractions of lime, 4, 6, 8 & 10 percent. Some experiments such as CBR, atterburg limits, compaction, consolidation and swelling was conducted on specimens. Results revealed that adding lime to soil would change its physical and mechanical properties. Adding lime increase the compression strength and consolidation coefficient and decrease swelling potential and maximum dry density. According to the results, Atterburg experiments show that presence of lime in soil increase the liquid limit of low plasticity soil and decrease the liquid limit of high plasticity soil, but totally it decreases the plasticity index of soils. Key words: soil stabilization, lime, compression strength, swelling, atterburg limits, compaction

  11. Accumulation of Pesticides in Anaerobic Clayey Till-Controls and Implications for Groundwater

    DEFF Research Database (Denmark)

    Jorgensen, Peter R.; Spliid, Niels H.

    2016-01-01

    of the phenoxy acids and triazines was much closer in sand-filled fractures and thin sand layers/lamina in the clay, suggesting that the migration of the same compounds along these textural preferential flow paths into the underlying aquifer was less different. Despite that a greater mass had originally been......Pesticide residuals after point-source pesticide spills in clay-rich aquitards may potentially affect underlying groundwater for many decades due to slow release of accumulated pollution in the clayey matrix material of the aquitard. In this study, we evaluated factors behind different degrees...... by diffusion and flow for the phenoxy acids (R = 1 to 2) than for the triazines (R = 9 to 16) in the clayey matrix material of the aquitard. This indicated that more rapid and greater accumulation could occur for the phenoxy acids in the clayey matrix than for the triazines. In contrast, the relative mobility...

  12. Seqüência Latossolo Amarelo - Podzólico Amarelo - Areias Quartzosas sob material da formação barreiras na região de Tucuruí, estado do Pará Oxisol-Ultisol-Entisol sequence developed from clayey material near Tucuruí region, Pará state, Brazil

    Directory of Open Access Journals (Sweden)

    J.A.M. Demattê

    1994-08-01

    Full Text Available Estudou-se uma seqüência de Latossolo Amarelo-Podzólico Amarelo-Areia Quartzosa desenvolvida em sedimentos da Formação Barreiras. A área se localiza no sul do Pará, nas proximidades entre Tucuruí e o Rio Moju, distando 65km da Usina Hidroelétrica de Tucuruí. Foi escolhida uma encosta de aproximadamente 1500 metros formada por Latossolo na parte alta e Podzólico Amarelo na encosta, ambos argilosos, terminando em amplo vale de fundo arenoso, com forte hidromorfísmo. Os regimes de temperatura são isohipertérmico e hipertérmico e os de umidade ústico e áquico, nas partes elevadas e fundo do vale, respectivamente. Foram abertas quatro trincheiras ao longo da encosta e feitas oito tradagens para apoio. O material de origem é representado pela caolinita. Verificou-se que a diferenciação lateral dos solos: Latossolo Amarelo na parte alta, Podzólico Latossólico na encosta e Areia Quartzosa no fundo do vale, pode ser devida principalmente a processos de remoção e/ou destruição de finos (argila silicatada + óxidos. O encharcamento temporário e a gleização acentuada, exerceram papel preponderante na diferenciação da seqüência estudada.The objective of this work was to study the genesis of an Oxisol-Ultisol-Entisol sequence, developed from sediments of the Barreiras Formation in the Tucurui region. The area is located about 65 km from Tucurui. In this area a soil topo sequence was selected, represented by a clayey oxisol in the higher parts, a clayey ultisol in the middle part, ending in an ample valley of sandy botton, with strong hidromorphism. The temperature regimes are isohyperthermic and hyperthermic and the moisture regimes are udic and aquic, in the higher parts and valley botton, respectively. Four profiles were examined and auger samples were taken in eight representative sites. The parent material is represented by clayey sediments from the Barreiras Formation. Chemically, the soils are leached with high aluminum

  13. Pressurized Anneal of Consolidated Powders

    Science.gov (United States)

    Nemir, David Charles (Inventor); Rubio, Edward S. (Inventor); Beck, Jan Bastian (Inventor)

    2017-01-01

    Systems and methods for producing a dense, well bonded solid material from a powder may include consolidating the powder utilizing any suitable consolidation method, such as explosive shockwave consolidation. The systems and methods may also include a post-processing thermal treatment that exploits a mismatch between the coefficients of thermal expansion between the consolidated material and the container. Due to the mismatch in the coefficients, internal pressure on the consolidated material during the heat treatment may be increased.

  14. Enhanced affordable methods for assessment of material characteristics and consolidation effects on stone and mortar

    Science.gov (United States)

    Drdacky, M.; Slizkova, Z.

    2012-04-01

    In situ considerate testing of surface cohesion of historic stone and mortar materials suffers from a lack of suitable affordable non-destructive methods. The problem is mainly important for assessment of surface degradation characteristics and/or evaluation of effectiveness of consolidation treatment of degraded historic materials. The paper presents two innovations of simple testing methods which provide reliable data on material cohesion and water uptake. The so called "Scotch Tape Test" or peeling test has been introduced into the field of conservation for testing the cohesion qualities of historic materials mainly stone and renders in sixties without any standards or reliably verified recommendations for the above mentioned application in the conservation practice. Licentious use without adequate knowledge and sufficient understanding leads to non-comparable and non-reproducible as well as in many cases incorrect and severely biased results and assessments. Therefore, the authors after a research and comparative testing have established limits for its application, reliable procedures and a "standard" protocol for testing of cohesion characteristics of brittle and quasi brittle materials mainly mortars and stones. This article presents a detailed analysis of the peeling test procedures, and suggests recommendations for performing peeling tests and for evaluating the obtained results. Also in situ testing of material water uptake is a very basic and indispensable technique in conservation practice and it correlates significantly with some other material characteristics. The capillary properties of porous materials can be measured in situ using a Karsten tube and modified tools or methods which are quite cumbersome, and cannot be performed on inclined surfaces, e.g. vaults or ceilings. There are other difficulties with Karsten tube measurements, e.g. problems with fixing a heavy glass tube on vertical surfaces, a need for two operators, and soiling of the surface

  15. Enhanced affordable methods for assessing material characteristics and consolidation effects on stone and mortar

    International Nuclear Information System (INIS)

    Drdácký, Miloš; Slížková, Zuzana

    2013-01-01

    It is rather difficult to set up non-destructive or considerate in situ tests for assessing material characteristics and consolidation effects on historic stone and mortar. However, some simple methods have proved to be helpful when applied appropriately and this paper provides brief information about two such methods: peeling tests, also known as the ‘Scotch tape’ method, and surface water uptake measurements using a digitized microtube. Both methods have some history of development and use Mora and Torraca (1965 Bollettino Istituto Centrale del Restauro (Rome) pp 109–32), Giorgi et al (2000 Stud. Conserv. 45 154–61), Tiano et al (2006 J. Cult. Heritage 7 49–55), Lehmann (2004 Thesis, Hochschule für Bildende Künste, Dresden pp 33–34), Drdácký et al (2011 Proc. European Workshop on Cultural Heritage Preservation pp 126–30) and Zíma (2011 Proc. 49th Int. Scientific Conf. on Experimental Stress Analysis pp 441–8) without any standardized support. This lack of a validated procedure can lead to some deficiencies and misinterpretations for applying the peeling test. Also, in the case of the digitized micro-tube, there can be some difficulties when the device is applied, which could prevent its wider adoption or even lead to rejection of the micro-tube technique. The paper summarizes basic principles for the application of both methods and reports illustrative results for laboratory and historic building investigations. (paper)

  16. Electro-chemo-hydro-mechanical coupling in clayey media

    International Nuclear Information System (INIS)

    Lemaire, Th.

    2004-12-01

    The aim of this study is to understand coupled phenomena that occur in swelling porous materials like clays. Electro-chemo-hydro-mechanical contributions are taken into account to analyze transfers in such minerals. In a first part, a general discussion is proposed to introduce mineralogical and physico- chemical considerations of clayey media. An important objective of this chapter is to show the crucial role of the microstructure. In a second part is presented an imbibition test in a MX80 bentonite powder. The hydraulic diffusivity versus water content curve's decrease is explained thanks to a double porosity model that shows the progressive collapse of meso-pores due to swelling effects at the micro-scale. Thus a multi-scale analysis is necessary to well describe clayey media behaviour. The third chapter exposes such a multi-scale modelling (periodic homogenization). It is based on the double-layer theory and introduces an innovative concept of virtual electrolyte solution. First numerical results are given in a simple geometry (parallel platelets). In the next part are proposed numerical simulations of two kinds: response of the system to a chemical gradient and simulation of electro-osmosis. The end of this chapter puts into relief the necessity to integrate pH effects in the model. In the last part, chemical surface exchanges are incorporated in the modelling to understand pH and ionic force roles in electro-osmotic process. (author)

  17. Determination of Required Ion Exchange Solution for Stabilizing Clayey Soils with Various PI

    OpenAIRE

    R. Ziaie Moayed; F. Allahyari

    2012-01-01

    Soil stabilization has been widely used to improve soil strength and durability or to prevent erosion and dust generation. Generally to reduce problems of clayey soils in engineering work and to stabilize these soils additional materials are used. The most common materials are lime, fly ash and cement. Using this materials, although improve soil property , but in some cases due to financial problems and the need to use special equipment are limited .One of the best method...

  18. Finding of no significant impact. Consolidation and interim storage of special nuclear material at Rocky Flats Environmental Technology Site

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-06-01

    The Department of Energy (DOE) has prepared an environmental assessment (EA), DOE/EA -- 1060, for the consolidation, processing, and interim storage of Category I and II special nuclear material (SNM) in Building 371 at the Rocky Flats Environmental Technology Site (hereinafter referred to as Rocky Flats or Site), Golden, Colorado. The scope of the EA included alternatives for interim storage including the no action alternative, the construction of a new facility for interim storage at Rocky Flats, and shipment to other DOE facilities for interim storage.

  19. Materials and Security Consolidation Complex Facilities Radioactive Waste Management Basis and DOE Manual 435.1-1 Compliance Tables

    International Nuclear Information System (INIS)

    2011-01-01

    Department of Energy Order 435.1, 'Radioactive Waste Management,' along with its associated manual and guidance, requires development and maintenance of a radioactive waste management basis for each radioactive waste management facility, operation, and activity. This document presents a radioactive waste management basis for Idaho National Laboratory's Materials and Security Consolidation Center facilities that manage radioactive waste. The radioactive waste management basis for a facility comprises existing laboratory-wide and facility-specific documents. Department of Energy Manual 435.1-1, 'Radioactive Waste Management Manual,' facility compliance tables also are presented for the facilities. The tables serve as a tool for developing the radioactive waste management basis.

  20. Finding of no significant impact. Consolidation and interim storage of special nuclear material at Rocky Flats Environmental Technology Site

    International Nuclear Information System (INIS)

    1995-06-01

    The Department of Energy (DOE) has prepared an environmental assessment (EA), DOE/EA -- 1060, for the consolidation, processing, and interim storage of Category I and II special nuclear material (SNM) in Building 371 at the Rocky Flats Environmental Technology Site (hereinafter referred to as Rocky Flats or Site), Golden, Colorado. The scope of the EA included alternatives for interim storage including the no action alternative, the construction of a new facility for interim storage at Rocky Flats, and shipment to other DOE facilities for interim storage

  1. Microstructural analysis of clayey ceramic incorporated with fluorescent lamp glass

    International Nuclear Information System (INIS)

    Morais, A.S.C.; Caldas, T.C.C.; Pereira, P.S.; Monteiro, S.N.; Vieira, C.M.F.

    2011-01-01

    This study aims to evaluate the effect of the incorporation of glass powder fluorescent lamp, from a decontamination process, in the microstructure of clayey ceramic. Formulations were prepared with incorporation of the waste in amounts of up to 10 wt.% into the clayey body. Specimens were prepared by uniaxial mold-press at 20 MPa and then fired at 850 and 1050°C. After firing, the microstructure of the ceramics was evaluated by optical microscopy (OM), scanning electron microscopy (SEM) and X-ray diffraction (XRD). The results showed that the incorporation of glass powder into the clayey body changes the microstructure of the ceramics. (author)

  2. Effect of temperature on damage and permeability of clayey soils and rocks

    International Nuclear Information System (INIS)

    Monfared, M.

    2011-04-01

    Storage of exothermic radioactive waste in deep low permeability geological formations such as clayey rocks and plastic clays is a solution considered for long term repositories. However the excavation of underground galleries creates a damaged zone (EDZ). The effect of the damage zone on the transport properties of the geological barrier has been widely studied. Within the framework of the TIMODAZ European project, emphasis has been put on the effect of temperature. As a partner of this project, the current work is performed to investigate the coupling effect between temperature, damage and permeability on Boom clay and Opalinus clay through an experimental study. View to the experimental difficulties related to the low permeability materials, a new hollow cylinder triaxial cell with short drainage path specifically designed to study the thermo-hydro-mechanical behaviour of very low permeable materials is developed during this work. The tests and the numerical analysis show that the short sample drainage path reduces significantly the time needed to re-saturate an initially unsaturated sample and it also permits to achieve drained conditions (i.e. negligible excess pore pressure during testing) with a higher loading rate. For Boom clay, the effect of the pore water thermal pressurisation on a sample with a pre-existing shear band is investigated. The undrained heating under shear stress decreases the effective stress on the sample which leads to its failure. An existing failure plane in the sample behaves like a preferential weakness plane which can be reactivated by pore water thermal pressurisation. The estimated shearing resistance along the sheared plane is smaller than that of the intact material. For the Opalinus clay-stone, drained heating on a saturated sample shows that this clay-stone behaves like a slightly over consolidated material (thermo-elasto-plastic behaviour) with transition from expansion to contraction at 65 C. The decrease of the permeability

  3. Synthesis of Pure Ca(OH)2 Nanoparticles and Superhydrophobic Suspensions: Consolidation and Waterproofing of Architectural Heritage Materials

    Science.gov (United States)

    Madrid Mendoza, Juan Antonio

    El objetivo de esta tesis es investigar sobre la sintesis, propiedades y aplicaciones de las nanoparticulas de Ca(OH)2 para consolidar materiales patrimoniales arquitectonicos. Las nanoparticulas de Ca(OH)2 se han utilizado recientemente en la conservacion del patrimonio, aunque algunos aspectos de la sintesis no son completamente comprendidos. En el presente estudio, hemos desarrollado metodos optimizados para obtener nanoparticulas de alta pureza mediante sintesis de fase homogenea y heterogenea utilizando diferentes materiales de partida. Se han realizado del orden de cien sintesis en diferentes condiciones para comprobar la validez y fiabilidad del metodo sintetico. Los resultados confirman que la temperatura de reaccion tiene una gran influencia en el tamano y la morfologia de las nanoparticulas de Ca(OH)2. Ademas, se ha investigado la estabilidad de las nanoparticulas a lo largo del tiempo en mezclas de 2-propanol / agua, en las que se encontro que la ausencia de agua era critica para evitar la aglomeracion de Ca(OH)2. Una vez dispersas en 2-propanol, las nanoparticulas se han utilizado para consolidar sustratos reales (piedra, adobe y estuco) confirmando su alto rendimiento en terminos de consolidacion superficial y - cuando se mezcla con ciertos surfactantes - en reduccion de la absorcion de agua. Asimismo, se ha investigado el uso de nanoparticulas modificadas basadas en M(OH)2, donde M=Ca2+, Mg2+, con el objetivo de mejorar tanto la cohesion superficial como la durabilidad de los materiales patrimoniales (p. ej. piedra Tabaire). Finalmente, el tratamiento de consolidacion basado en nanoparticulas puras de Ca(OH)2 se utilizo en emplazamientos con valor patrimonial, como edificios historicos y yacimientos arqueologicos (Teatro Romano de Cartagena) obteniendo resultados satisfactorios. The aim of this thesis is to investigate on the synthesis, properties and applications of Ca(OH)2 nanoparticles to consolidate architectural heritage materials. Ca(OH)2

  4. Study of the water retention and the consolidation of partially saturated soils in a thermo-hydro-mechanical framework

    International Nuclear Information System (INIS)

    Salager, Simon

    2007-01-01

    This work is concerned with the study of water retention and consolidation of unsaturated soils in a thermo-hydro-mechanical framework. It is organized into two parts which deal respectively with deformation and temperature effects on hydric behaviour, and suction and temperature effects on mechanical behaviour. In the first part, we point out the relevance of the characteristic surface concept for soils as opposed to the retention curve, which has limited modelling power in the case of deformable media. The characteristic surface concept is experimentally illustrated for the example of a clayey silty sand. Its modelling is based on a large sample of experimental investigations with about 240 measurements of the triplet void ratio, water content, suction. In addition, a thermo-hydric behaviour model is proposed in order to determine the characteristic surface and the retention curve for a given temperature. This model is validated for the case of two materials: a ceramic and a clayey silty sand through direct testing, and for other materials on the basis of an analysis of the literature. Finally, we present an application to the determination of the permeability of unsaturated soils taking into account deformation and temperature. In the second part, temperature and suction effects on the mechanical behaviour are studied through consolidation tests on 'Sion' silt. These tests are performed for different temperatures and suctions. For each test, swelling and compression indexes, as well as the pre-consolidation pressure are measured. The influence of temperature and suction on these essential parameters of mechanical behaviour is determined. Finally, we propose a theoretical model which account for pre-consolidation pressure as a function of temperature and suction. (author)

  5. The consolidation of a powder material in conditions of combined influence of different technological factors

    Directory of Open Access Journals (Sweden)

    Dorofeyev V.Yu.

    2003-01-01

    Full Text Available In the present paper the problems, connected with the formation of a powder material and its surface layers in conditions of chemical thermal treatment and impregnation with melt, combined with the use of mechanical loads at different process stages are examined. The new results of liquid phase influence on compaction of powder preforms, subjected to impregnation, are obtained. The presence of a liquid phase in preform surface layers can also be connected with the change of the materials chemical composition as the result of boronizing, siliconizing or other kinds of chemical thermal treatment.

  6. Study of Wettability of Clayey Ceramic and Fluorescent Lamp Glass Waste Powders

    Science.gov (United States)

    Morais, Alline Sardinha Cordeiro; Monteiro, Sergio Neves; Ribeiro, Sebastião; Sardinha, Leonardo Carneiro; Vieira, Carlos Maurício Fontes

    The glass tube of spent fluorescent lamps is contaminated with mercury, which might be a serious hazard in the case of conventional recycling by melting with other glasses. A possible solution could be its incorporation into a clay body to fabricate common fired ceramics such as bricks and tiles. The objective of this work is to characterize a type of fluorescent lamp glass waste to be incorporated into a clayey ceramic. The characterization was performed in terms of wettability tests to evaluate the interaction between the surface of the clayey ceramic and glass waste as a function of the firing temperature. The results showed that the contact angle decreased with increasing temperature, reaching a value of 79°, at a temperature of 1100°C, but not sufficient to completely wet the ceramic. However, compatible chemical composition and reduction of porosity by the flow of soft glass waste between the clay particles favor the consolidation of the ceramics structure above 900°C.

  7. Investigation of Self Consolidating Concrete Containing High Volume of Supplementary Cementitious Materials and Recycled Asphalt Pavement Aggregates

    Science.gov (United States)

    Patibandla, Varun chowdary

    The use of sustainable technologies such as supplementary cementitiuous materials (SCMs), and/or recycled materials is expected to positively affect the performance of concrete mixtures. However, it is important to study and qualify such mixtures and check if the required specifications of their intended application are met before they can be implemented in practice. This study presents the results of a laboratory investigation of Self Consolidating concrete (SCC) containing sustainable technologies. A total of twelve concrete mixtures were prepared with various combinations of fly ash, slag, and recycled asphalt pavement (RAP). The mixtures were divided into three groups with constant water to cementitiuous materials ratio of 0.37, and based on the RAP content; 0, 25, and 50% of coarse aggregate replaced by RAP. All mixtures were prepared to achieve a target slump flow equal to or higher than 500 mm (24in). A control mixture for each group was prepared with 100% Portland cement whereas all other mixtures were designed to have up to 70% of portland cement replaced by a combination of supplementary cementitiuous materials (SCMs) such as class C fly ash and granulated blast furnace slag. The properties of fresh concrete investigated in this study include flowability, deformability; filling capacity, and resistance to segregation. In addition, the compressive strength at 3, 14, and 28 days, the tensile strength, and the unrestrained shrinkage up to 80 days was also investigated. As expected the inclusion of the sustainable technologies affected both fresh and hardened concrete properties. Analysis of the experimental data indicated that inclusion of RAP not only reduces the ultimate strength, but it also affected the compressive strength development rate. Moreover, several mixes satisfied compressive strength requirements for pavements and bridges; those mixes included relatively high percentages of SCMs and RAP. Based on the results obtained in this study, it is not

  8. Hydrate bearing clayey sediments: Formation and gas production concepts

    KAUST Repository

    Jang, Jaewon; Santamarina, Carlos

    2016-01-01

    Hydro-thermo-chemo and mechanically coupled processes determine hydrate morphology and control gas production from hydrate-bearing sediments. Force balance, together with mass and energy conservation analyses anchored in published data provide robust asymptotic solutions that reflect governing processes in hydrate systems. Results demonstrate that hydrate segregation in clayey sediments results in a two-material system whereby hydrate lenses are surrounded by hydrate-free water-saturated clay. Hydrate saturation can reach ≈2% by concentrating the excess dissolved gas in the pore water and ≈20% from metabolizable carbon. Higher hydrate saturations are often found in natural sediments and imply methane transport by advection or diffusion processes. Hydrate dissociation is a strongly endothermic event; the available latent heat in a reservoir can sustain significant hydrate dissociation without triggering ice formation during depressurization. The volume of hydrate expands 2-to-4 times upon dissociation or CO2single bondCH4 replacement. Volume expansion can be controlled to maintain lenses open and to create new open mode discontinuities that favor gas recovery. Pore size is the most critical sediment parameter for hydrate formation and gas recovery and is controlled by the smallest grains in a sediment. Therefore any characterization must carefully consider the amount of fines and their associated mineralogy.

  9. Factors impacting the electro conductivity variations of clayey soils

    International Nuclear Information System (INIS)

    Ouhadi, V. R.; Goodarzi, A. R.

    2007-01-01

    The variation of pore fluid properties in soil has a major effect on soil behaviour. This effect is a function of pore fluid properties and soil mineralogy. Such variation usually happens in the reservoirs of dams or in some geotechnical projects. The electro conductivity measurement is a simple method to monitor any variation in the pore fluid of soils. electro conductivity is the ability of a material to transmit (conduct) an electrical current. This paper focuses attention on the effect of soil-pore fluid interaction on the electro conductivity of clayey soils. A set of physico-chemical experiments are performed and the role of different factors including soil pH, soil mineralogy, soil: water ratio, cation and anion effects are investigated. The results of this study indicate that for soil that has a relatively low CEC, the anion type is an important factor, while the cation type does not noticeably affect the electro conductivity of the soil-solution. However, for such soil, an electrolyte property, i.e. its solubility, is much more effective than the CEC of the soil. In addition, it was observed that in the presence of neutral salts such as pore fluid, the pH of the soil-solution decreases causing an increase in the electro conductivity of the soil sample

  10. Hydrate bearing clayey sediments: Formation and gas production concepts

    KAUST Repository

    Jang, Jaewon

    2016-06-20

    Hydro-thermo-chemo and mechanically coupled processes determine hydrate morphology and control gas production from hydrate-bearing sediments. Force balance, together with mass and energy conservation analyses anchored in published data provide robust asymptotic solutions that reflect governing processes in hydrate systems. Results demonstrate that hydrate segregation in clayey sediments results in a two-material system whereby hydrate lenses are surrounded by hydrate-free water-saturated clay. Hydrate saturation can reach ≈2% by concentrating the excess dissolved gas in the pore water and ≈20% from metabolizable carbon. Higher hydrate saturations are often found in natural sediments and imply methane transport by advection or diffusion processes. Hydrate dissociation is a strongly endothermic event; the available latent heat in a reservoir can sustain significant hydrate dissociation without triggering ice formation during depressurization. The volume of hydrate expands 2-to-4 times upon dissociation or CO2single bondCH4 replacement. Volume expansion can be controlled to maintain lenses open and to create new open mode discontinuities that favor gas recovery. Pore size is the most critical sediment parameter for hydrate formation and gas recovery and is controlled by the smallest grains in a sediment. Therefore any characterization must carefully consider the amount of fines and their associated mineralogy.

  11. Mineralogical and particulate morphological characterization of geophagic clayey soils from Botswana

    Directory of Open Access Journals (Sweden)

    Georges-Ivo Ekosse

    2012-12-01

    Full Text Available This study focused on determining the minerals composition and particle morphology of geophagic clayey soils from Botswana in order to infer on how they could influence human health. Six representative geophagic clayey soils from Botswana were mineralogically characterized using X-ray powder diffractometry (XRPD, optical microscopy, and environmental scanning electron microscopy (ESEM. Results of identified mineral phases revealed quartz (SiO2 as the most dominant in all samples constituting close to 70 wt %; followed by goethite (FeO.OH having a mean concentration of 9 wt%, and kaolinite (Al2Si2O5(OH4 with a mean concentration of 8 wt%. Other minerals present were smectite ((Na,Ca(Al,Mg6(Si4O103(OH6-n(H2O, mica (AB2-3(Al,SiSi3O10(F,OH2, feldspar (Na/K(AlSi3O8 and hematite (Fe2O3. The quartz particles were generally coarse; and angular to very angular in morphology. Due to ions present in goethite, kaolinite, and smectite, these minerals impact positively on properties of geophagic clayey soils and could possibly influence human health when consumed. The quartz particles could negatively affect dental enamel as a result of mastication; and cause abrasion of the walls of the gastro-intestinal tract which may lead to rupturing. Although the studied clayey soils could have potential to provide medicinal benefits to the consumer, there is need for beneficiation exercise to be conducted to reduce the coarse angular particles contained in them. It is therefore necessary for constructive efforts to be directed at beneficiating geophagic materials which will render them safe for human consumption.DOI: http://dx.doi.org/10.4314/bcse.v26i3.6

  12. Environmental assessment for consolidation of certain materials and machines for nuclear criticality experiments and training

    International Nuclear Information System (INIS)

    1996-01-01

    In support of its assigned missions and because of the importance of avoiding nuclear criticality accidents, DOE has adopted a policy to reduce identifiable nuclear criticality safety risks and to protect the public, workers, government property and essential operations from the effects of a criticality accident. In support of this policy, the Los Alamos Critical Experiments Facility (LACEF) at the Los Alamos National Laboratory (LANL) Technical Area (TA) 18, provides a program of general purpose critical experiments. This program, the only remaining one of its kind in the United States, seeks to maintain a sound basis of information for criticality control in those physical situations that DOE will encounter in handling and storing fissionable material in the future, and ensuring the presence of a community of individuals competent in practicing this control

  13. Effects of biochars on hydraulic properties of clayey soil

    Science.gov (United States)

    Zhen, Jingbo; Palladino, Mario; Lazarovitch, Naftali; Bonanomi, Giuliano; Battista Chirico, Giovanni

    2017-04-01

    Biochar has gained popularity as an amendment to improve soil hydraulic properties. Since biochar properties depend on feedstocks and pyrolysis temperatures used for its production, proper selection of biochar type as soil amendment is of great importance for soil hydraulic properties improvement. This study investigated the effects of eight types of biochar on physical and hydraulic properties of clayey soil. Biochars were derived from four different feedstocks (Alfalfa hay, municipal organic waste, corn residues and wood chip) pyrolyzed at two different temperatures (300 and 550 °C). Clayey soil samples were taken from Leone farm (40° 26' 15.31" N, 14° 59' 45.54" E), Italy, and were oven-dried at 105 °C to determine dry bulk density. Biochars were mixed with the clayey soil at 5% by mass. Bulk densities of the mixtures were also determined. Saturated hydraulic conductivities (Ks) of the original clayey soil and corresponding mixtures were measured by means of falling-head method. Soil water retention measurements were conducted for clayey soil and mixtures using suction table apparatus and Richards' plate with the pressure head (h) up to 12000 cm. van Genuchten retention function was selected to evaluate the retention characteristics of clayey soil and mixtures. Available water content (AWC) was calculated by field capacity (h = - 500 cm) minus wilting pointing (h = -12000 cm). The results showed that biochar addition decreased the bulk density of clayey soil. The Ks of clayey soil increased due to the incorporation of biochars except for waste and corn biochars pyrolyzed at 550 °C. AWC of soils mixed with corn biochar pyrolyzed at 300 °C and wood biochar pyrolyzed at 550 °C, increased by 31% and 7%, respectively. Further analysis will be conducted in combination of biochar properties such as specific surface area and total pore volume. Better understanding of biochar impact on clayey soil will be helpful in biochar selection for soil amendment and

  14. Consolidated guidance about materials licenses: Program-specific guidance about portable gauge licenses. Final report; Volume 1

    Energy Technology Data Exchange (ETDEWEB)

    Vacca, P.C.; Whitten, J.E.; Pelchat, J.M.; Arredondo, S.A.; Matson, E.R.; Lewis, S.H.; Collins, D.J.; Santiago, P.A. [Nuclear Regulatory Commission, Washington, DC (United States). Div. of Industrial and Medical Nuclear Safety; Tingle, W. [Dept. of Environment, Health, and Natural Resources, Raleigh, NC (United States). Div. of Radiation Protection

    1997-05-01

    As part of its redesign of the materials licensing process, NRC is consolidating and updating numerous guidance documents into a single comprehensive repository as described in NUREG-1539 and draft NUREG-1541. NUREG-1556, Vol. 1, is the first program-specific guidance developed for the new process and will serve as a template for subsequent program-specific guidance. This document is intended for use by applicants, licensees, and NRC staff and will also be available to Agreement States. This document supersedes the guidance previously found in draft Regulatory Guide DG-0008, ``Applications for the Use of Sealed Sources in Portable Gauging Devices,`` and in NMSs Policy and guidance Directive 2-07, ``Standard Review Plan for Applications for Use of Sealed Sources in Portable Gauging Devices.`` This final report takes a more risk-informed, performance-based approach to licensing portable gauges, and reduces the information(amount and level of detail) needed to support an application to use these devices. It incorporates many suggests submitted during the comment period on draft NUREG-1556, Volume 1. When published, this final report should be used in preparing portable gauge license applications. NRC staff will use this final report in reviewing these applications.

  15. Consolidated guidance about materials licenses: Program-specific guidance about portable gauge licenses. Final report; Volume 1

    International Nuclear Information System (INIS)

    Vacca, P.C.; Whitten, J.E.; Pelchat, J.M.; Arredondo, S.A.; Matson, E.R.; Lewis, S.H.; Collins, D.J.; Santiago, P.A.; Tingle, W.

    1997-05-01

    As part of its redesign of the materials licensing process, NRC is consolidating and updating numerous guidance documents into a single comprehensive repository as described in NUREG-1539 and draft NUREG-1541. NUREG-1556, Vol. 1, is the first program-specific guidance developed for the new process and will serve as a template for subsequent program-specific guidance. This document is intended for use by applicants, licensees, and NRC staff and will also be available to Agreement States. This document supersedes the guidance previously found in draft Regulatory Guide DG-0008, ''Applications for the Use of Sealed Sources in Portable Gauging Devices,'' and in NMSs Policy and guidance Directive 2-07, ''Standard Review Plan for Applications for Use of Sealed Sources in Portable Gauging Devices.'' This final report takes a more risk-informed, performance-based approach to licensing portable gauges, and reduces the information(amount and level of detail) needed to support an application to use these devices. It incorporates many suggests submitted during the comment period on draft NUREG-1556, Volume 1. When published, this final report should be used in preparing portable gauge license applications. NRC staff will use this final report in reviewing these applications

  16. Outside Mainstream Electronic Databases: Review of Studies Conducted in the USSR and Post-Soviet Countries on Electric Current-Assisted Consolidation of Powder Materials

    Directory of Open Access Journals (Sweden)

    Eugene G. Grigoryev

    2013-09-01

    Full Text Available This paper reviews research articles published in the former USSR and post-soviet countries on the consolidation of powder materials using electric current that passes through the powder sample and/or a conductive die-punch set-up. Having been published in Russian, many of the reviewed papers are not included in the mainstream electronic databases of the scientific articles and thus are not known to the scientific community. The present review is aimed at filling this information gap. In the paper, the electric current-assisted sintering techniques based on high- and low-voltage approaches are presented. The main results of the theoretical modeling of the processes of electromagnetic field-assisted consolidation of powder materials are discussed. Sintering experiments and related equipment are described and the major experimental results are analyzed. Sintering conditions required to achieve the desired properties of the sintered materials are provided for selected material systems. Tooling materials used in the electric current-assisted consolidation set-ups are also described.

  17. Geotechnical properties of clayey soil stabilized with cement ...

    African Journals Online (AJOL)

    The study was conducted to investigate the different effects of cement-sawdust ash and cement on a clayey soil sampled from Mandate Lodge, Landmark University, Omu-Aran, Nigeria. The binder mix of cementsawdust ash (CSDA) was mixed in a ratio of 1:1. The CSDA and cement were added to the soil samples at ...

  18. Mechanical properties of clayey soils and thermal solicitations

    International Nuclear Information System (INIS)

    Boisson, J.Y.

    1992-01-01

    Changes in permeability and mechanical properties of three clayey soils with temperature have been studied by using a special oedometric cell. The action of a thermal solicitation on the fabric and the behavior of the samples is highlighted. 3 figs., 1 tab

  19. Multiple-scale hydraulic characterization of a surficial clayey aquitard overlying a regional aquifer in Louisiana

    Science.gov (United States)

    Chapman, Steven W.; Cherry, John A.; Parker, Beth L.

    2018-03-01

    The vertical hydraulic conductivity (Kv) of a 30-m thick surficial clayey aquitard overlying a regional aquifer at an industrial site in the Mississippi River Valley in Louisiana was investigated via intensive hydraulic characterization using high resolution vertical hydraulic head profiles with temporal monitoring and laboratory tests. A study area was instrumented with a semi-circular array of piezometers at many depths in the aquitard at equal distance from a large capacity pumping well including replicate piezometers. Profiles showed negligible head differential to 20 m bgs, below which there was an abrupt change in vertical gradients over the lower 8-10 m of the aquitard. Hydraulic characteristics are strongly associated with depositional environment; the upper zone of minimal head differentials with depth and minimal variation over time correlates with Paleo-Mississippi River backswamp deposits, while the lower zone with large head differentials and slow but moderate head changes correlates with lacustrine deposits. The lower zone restricts groundwater flow between the surface and underlying regional aquifer, which is hydraulically connected to the Mississippi River. Lab tests on lacustrine samples show low Kv (8 × 10-11-4 × 10-9 m/s) bracketing field estimates (6 × 10-10 m/s) from 1-D model fits to piezometric data in response to large aquifer head changes. The slow response indicates absence of through-going open fractures in the lacustrine unit, consistent with geotechnical properties (high plasticity, normal consolidation), suggesting high integrity that protects the underlying aquifer from surficial contamination. The lack of vertical gradients in the overlying backswamp unit indicates abundant secondary permeability features (e.g. fractures, rootholes) consistent with depositional and weathering conditions. 2-D stylized transient flow simulations including both units supports this interpretation. Other published reports on surficial aquitards in the

  20. Process for soil consolidation

    Energy Technology Data Exchange (ETDEWEB)

    Herrick, F W; Brandstrom, R I

    1967-01-09

    In this process for the formation of a consolidated aggregate, a mass of solid particles is combined with an aqueous alkaline consolidating compound which forms a gel. This gel consists principally of a mixture of the following: a vegetable polyphenolic material; one of the group of catechins; condensed tannins and extract of the bark of coniferous trees; with 1-10% by weight of formaldehyde; and a catalyst of the group of water-soluble salts of chromium, iron, and aluminum. This catalyst serves to catalyze the reaction of formation of the gel.

  1. Removal of PAHs from contaminated clayey soil by means of electro-osmosis

    KAUST Repository

    Lima, Ana T.

    2011-06-01

    The removal of polycyclic aromatic hydrocarbons (PAHs) from clayey soils is an intricate task. The low porosity of compacted clayey soil hinders bacterial activity and makes convective removal by hydraulic flow impossible. Electro-osmosis is a process that has been used for the mobilization and cleanup of contaminants in clayey soils with varying successes. The present study focuses on the remediation of a contaminated peaty clay soil, located in Olst - the Netherlands, by means of electro-osmosis. The soil was originally contaminated by an asphalt production plant, active from 1903 to 1983, and presents high levels of all 16 priority PAHs indicated by the US Environmental Protection Agency (EPA). Such a long contact times of PAH with the soil (≥100 years) presents a unique study material with well established solid/liquid contaminant partitioning equilibrium, preferable to artificially spiked soil. A batch of 6 electro-osmosis laboratory experiments was carried out to study the removal of 16 PAHs through electro-osmosis. In these experiments, water and a surfactant (Tween 80) were used to enhance the PAH desorption. The electro-osmotic conductivities ranged from 2.88 × 10-10 to a substantial 1.19 × 10-7 m2 V-1 s -1 when applying a current density of 0.005-0.127 A m-2. Electro-osmosis was expected to occur towards the cathode, because of natural soil characteristics (negative zeta potential), but presented scattered directions. The use of reference electrodes proved to be very effective to the prediction of the flow direction. Finally, the addition of Tween 80 as a surfactant enhanced PAH removal up to 30% of the total PAH content of the soil in 9 days. © 2011 Elsevier B.V.

  2. Sand consolidation

    Energy Technology Data Exchange (ETDEWEB)

    Spain, H H

    1965-01-21

    In a sand consolidation method in which there is injected a mixture of resin-forming liquids comprising an aryl-hydroxy low molecular weight compound, a water- soluble aldehyde, and a catalyst, an improvement is claimed which comprises diluting the resin-forming liquids with a diluent and with water so that the yield of the resin is sufficient to consolidate the sand particles with the minimum desirable pressure. The diluent may be mutually soluble in water and in the resin-forming liquids, and does not affect the setting time of the polymer. The aldehyde and the aryl-hydroxy compound may be in ratio of 5:1, and the diluent, methyl alcohol, is present in a ratio of 2:1 with reference to the water.

  3. Quick clay and landslides of clayey soils

    NARCIS (Netherlands)

    Khaldoun, A.; Moller, P.; Fall, A.; Wegdam, G.; de Leeuw, B.; Méheust, Y.; Fossum, J.O.; Bonn, D.

    2009-01-01

    We study the rheology of quick clay, an unstable soil responsible for many landslides. We show that above a critical stress the material starts flowing abruptly with a very large viscosity decrease caused by the flow. This leads to avalanche behavior that accounts for the instability of quick clay

  4. Clayey landslide initiation and acceleration strongly modulated by soil swelling

    Science.gov (United States)

    Schulz, William; Smith, Joel B.; Wang, Gonghui; Jiang, Yao; Roering, Joshua J.

    2018-01-01

    Largely unknown mechanisms restrain motion of clay-rich, slow-moving landslides that are widespread worldwide and rarely accelerate catastrophically. We studied a clayey, slow-moving landslide typical of thousands in northern California, USA, to decipher hydrologic-mechanical interactions that modulate landslide dynamics. Similar to some other studies, observed pore-water pressures correlated poorly with landslide reactivation and speed. In situ and laboratory measurements strongly suggested that variable pressure along the landslide's lateral shear boundaries resulting from seasonal soil expansion and contraction modulated its reactivation and speed. Slope-stability modeling suggested that the landslide's observed behavior could be predicted by including transient swell pressure as a resistance term, whereas modeling considering only transient hydrologic conditions predicted movement 5–6 months prior to when it was observed. All clayey soils swell to some degree; hence, our findings suggest that swell pressure likely modulates motion of many landslides and should be considered to improve forecasts of clayey landslide initiation and mobility.

  5. Quick clay and landslides of clayey soils.

    Science.gov (United States)

    Khaldoun, Asmae; Moller, Peder; Fall, Abdoulaye; Wegdam, Gerard; De Leeuw, Bert; Méheust, Yves; Otto Fossum, Jon; Bonn, Daniel

    2009-10-30

    We study the rheology of quick clay, an unstable soil responsible for many landslides. We show that above a critical stress the material starts flowing abruptly with a very large viscosity decrease caused by the flow. This leads to avalanche behavior that accounts for the instability of quick clay soils. Reproducing landslides on a small scale in the laboratory shows that an additional factor that determines the violence of the slides is the inhomogeneity of the flow. We propose a simple yield stress model capable of reproducing the laboratory landslide data, allowing us to relate landslides to the measured rheology.

  6. Hydric transfer in swelling clayey soils: influence of confinement; Transfert hydrique dans des sols argileux gonflants: influence du confinement

    Energy Technology Data Exchange (ETDEWEB)

    Rolland, S

    2002-01-01

    Description of imbibition and swelling mechanisms in clayey soils represents an important stake in different scientific domains such as agronomy, geotechnics or petroleum industry. The aim of the present work is to show the effects of hydro-mechanical couplings during imbibition in a swelling clayey medium, under different confinement conditions. Our material is a bentonite-silt mixture, prepared with a known water content and compacted with a double-piston technique. This method allows us to produce uniform soil samples, in terms of humidity and bulk density. Experiments related to bottom imbibition are then carried out for three types of mechanical boundary conditions (free, oedometric, fixed volume). The non-intrusive dual-energy gamma-ray technique is used to assess the local variation of bulk density and humidity. Finally, the three imbibition kinetics are compared for each experiment in terms of hydraulic diffusivity, described in a Lagrangian way. (author)

  7. Preliminary analysis in a clayey mass aimed at ceramic blocks production: physical and mineralogical characteristics

    International Nuclear Information System (INIS)

    Silva, L.J.M.D. da; Apolonio, T.G.; Salviano, A.F.; Taveira, S.K.A.; Garcia, T.G.C.; Silva, J; Luna, P.A.; Macedo, R.S.

    2016-01-01

    The physical, chemical and mineralogical characterization of the clayey mass are important in determining its properties, allowing a better knowledge of the raw material used in the manufacture of ceramic products. This work aims to characterize the raw material used in the manufacture of ceramic sealing blocks in a ceramic industry. Thus, it was evaluated by laboratory tests the raw material used in the production of ceramic blocks in a ceramics industry in the region of Carnauba dos Dantas, RN. The methodology used in the tests is the same as the IPT, which consists in carrying out the plasticity testing, particle size, chemical analysis and X-ray diffraction. Results indicate that the sample studied by the physical and mineralogical characteristics, has the potential to be applied in the manufacture of red ceramic products for use in construction. (author)

  8. Mechanical behaviour and rupture in clayey rocks studied by x-ray micro tomography

    International Nuclear Information System (INIS)

    Lenoir, N.

    2006-03-01

    Within the framework of feasibility studies of underground repositories for radioactive waste, the study of permeability evolution with damage of the host layer is crucial. The goals of this work were: (i) to characterize experimentally the damage of two clayey rocks (BEAUCAIRE MARL and EAST SHALE) with x-ray micro tomography, (ii) to develop a high pressure triaxial set-up adapted to permeability measurement on very low permeability rocks.A number of original triaxial devices have been realised to characterize damage of clayey rocks, under deviatoric loading, with x-ray micro tomography on a synchrotron beamline at the ESRF (Grenoble). Localized damage and its evolution have been characterized at a fine scale (of order of ten microns). Digital image correlation techniques, extended to 3d images, have been used to measure incremental strain fields from tomographic images. we demonstrated that these techniques are very useful in the study of the localized damage of geo-materials and especially for the initiation. A high pressure triaxial device has been realised to measure permeability evolution of the east shale as a function of applied stress (isotropic and deviatoric). The particularity of this set-up is the small size of the test specimen (cylinder of 10 mm in diameter and 20 mm in height) which allows significant reduction of test duration. (author)

  9. Consolidation of tailings

    International Nuclear Information System (INIS)

    Nelson, J.D.; Wardwell, R.E.; Abt, S.R.; Staub, W.P.

    1983-09-01

    The integrity of cover systems placed on tailings impoundments will be affected by the potential for differential settlement of the tailings surface. Settlement of the sand fraction will occur relatively rapidly. The slimes will take longer time for consolidation and will produce greater settlement. This report reviews the phenomenon of consolidation for saturated and unsaturated tailings. The effect of load application by cover placement and the extent to which dewatering of tailings will cause consolidation are considered. In addition, the feasibility of inducing consolidation by alternative means and the potential applicability of these methods to tailings impoundments reclamation are discussed. Differential settlement of the tailings will cause tensile strain to be developed in covers. This strain could be large enough to cause cracking within a relatively brittle compacted clay. Dewatering of tailings by drainage can cause settlement even greater than that by placement of a cover material. Dewatering of the tailings would also increase the stability of the tailings surface, thereby enhancing reclamation operations. Consequently, in view of the enhanced surface stability and the fact that a portion of the differential settlement can be accomplished prior to cover placement, dewatering of tailings impoundments during operations may have benefical effects

  10. EDZ and permeability in clayey rocks

    International Nuclear Information System (INIS)

    Levasseur, Severine; Collin, Frederic; Charlier, Robert; Besuelle, Pierre; Chambon, Rene; Viggiani, Cino

    2010-01-01

    Document available in extended abstract form only. Deep geological layers are being considered as potential host rocks for the high level radioactivity waste disposals. During drilling in host rocks, an excavated damaged zone - EDZ is created. The fluid transmissivity may be modified in this damaged zone. This paper deals with the permeability evolution in relation with diffuse and/or localized crack propagation in the material. We mainly focus on argillaceous rocks and on some underground laboratories: Mol URL in Boom clay, Bure URL in Callovo-Oxfordian clay and Mont-Terri URL in Opalinus clay. First, observations of damage around galleries are summarized. Structure of damage in localized zone or in fracture has been observed at underground gallery scale within the excavation damaged zone (EDZ). The first challenge for a correct understanding of all the processes occurring within the EDZ is the characterization at the laboratory scale of the damage and localization processes. The observation of the initiation and propagation of the localized zones needs for advanced techniques. X-ray tomography is a non-destructive imaging technique that allows quantification of internal features of an object in 3D. If mechanical loading of a specimen is applied inside a X-ray CT apparatus, successive 3D images at different loading steps show the evolution of the specimen. However, in general volumetric strain in a shear band is small compared to the shear strain and, unfortunately, in tomographic images grey level is mainly sensitive to the local mass density field. Such a limitation has been recently overcome by complementing X-ray tomography with 3D Volumetric Digital Image Correlation (V-DIC) which allows the determination of the full strain tensor field. Then it is possible to further explore the progression of localized deformation in the specimen. The second challenge is the robust modelling of the strain localized process. In fact, modelling the damage process with finite

  11. Studying of the combined salts effect on the engineering properties of clayey soil

    Directory of Open Access Journals (Sweden)

    Al-Obaidi Anwar

    2018-01-01

    Full Text Available In recent years, a number of studies had been performed to investigate the effect of pore water chemistry on the strength and compressibility characteristics of soil. Although the effect of chloride and sulfates salts separately in pore fluids on the geotechnical properties of soil seems to be well understood, but the influence of combined effect of sulfates and chlorides in pore water on the behavior of soil is still unclear mostly due to the limited numbers of studies as well as the complexity of processes that may occur in soil (with the presence of salts in pore water-soil interaction. Southern regions of Iraq, especially Basra suffers from low water levels in the summer season in addition to the lack of rain water, which causes a significant increase of salt in the Shatt al Arab. Water salinity continues to increase with time. To investigate the combined impacts of water salinity on the behavior of clayey soils, the basic characteristics of the soil brought from Al-Nahrawan site was studied. Chemical methods were done with three types of water (distilled, water of highly saline as Shatt Al-Arab water and water of Tarmiya as moderate saline water. The effect of water salinity on the geotechnical properties of fine grain soil was investigated. Different laboratory tests such as Atterberg limits, standard compaction, consolidation and shear strength of soil .Results showed that the presence of perceptible amounts of dissolved salts in water can lead to changes in the engineering properties of the soil.

  12. Analysis of the nano-scale structure of a natural clayey soil using the small angle neutron scattering method

    International Nuclear Information System (INIS)

    Itakura, T.; Bertram, W.K.; Hathaway, P.V.; Knott, R.B.

    2001-01-01

    The small angle neutron scattering method (SANS) was used to analyze the nano-structure of a natural clayey soil used for containment of industrial liquid wastes. A Tertiary clay deposit called the Londonderry clay was used to contain the wastes in a state-run landfill facility in NSW. A number of site assessments have been carried out at the site and continual efforts have been made to characterize interactions between soil materials and contaminants at the site. Hence, it is of research and practical interest to investigate the effects of deformation on the nano-scale structure of the soil. Experiments have been conducted to analyze the structure of reconstituted clayey soil samples that were subjected to uniaxial compression ranging from 200 kPa to 800 kPa. The small angle neutron scattering instrument was used to measure the scattering intensity of these samples at a scattering vector (q) range between 0.01 and 0.1 Angstroms -1 . The sector integration technique was used to analyse elliptical scattering patterns along the major and minor axes. A relation between stress, void ratio and nano-scale structure properties was then briefly discussed for use in assessing the performance of clayey soils as in situ barriers

  13. Consolidated financial statements

    OpenAIRE

    Blaha, Miroslav

    2010-01-01

    This work provides basic information about consolidation and consolidated financial statements. In the beginning there are definisions of the members of the group under discussion and their relationship. Hereafter concepts of consolidation, accounting methods and methods of consolidation are discussed. It also compares approach of different accounting systems to consolidation.

  14. Swelling/shrinkage of compacted and natural clayey soils

    International Nuclear Information System (INIS)

    Nowamooz, H.

    2007-12-01

    This thesis presents an experimental study performed on compacted loose and natural dense expansive soils using osmotic odometers. Several successive cycles were applied under three different low constant vertical net stresses. The loose soil presents a significant shrinkage accumulation while the dense one produces the swelling accumulation during the suction cycles. The suction cycles induced an equilibrium stage which indicates an elastic behaviour of the samples. At the end of suction cycles, a loading/unloading test was performed at the constant suctions for both materials. The mechanical parameters, i.e. the virgin compression index lambda(s), the apparent pre-consolidation stress p0(s) and the elastic compression index values lambda are completely dependent on the followed stress paths. The whole experimental results made it possible to define the yielding surfaces: suction limit between micro and macrostructure (Lm/M), loading collapse (LC) and saturation curve (SCS). The suction limit (Lm/M) depends completely to the soil fabrics and to the diameter separating the micro- and macrostructure. The pre-consolidation stress variation with suction is represented by the LC surface. The compression curves at different imposed suctions converge towards the saturated state for the high applied vertical stresses. We consider the saturation pressure (Psat) as the necessary pressure to reach the saturated state for an imposed suction. The higher the suction, the higher the saturation pressure. The yielding surface representing this pressure as a function of suction is called the saturation curve (SCS). Generally we can state that the suction cycles unified the LC and SC surfaces and increased the (Lm/M) up to a higher value. (author)

  15. Complex conductivity of oil-contaminated clayey soils

    Science.gov (United States)

    Deng, Y.; Revil, A.; Shi, X.

    2017-12-01

    Non-intrusive hydrogeophysical techniques have been wildly applied to detect organic contaminants because of the difference of electrical properties for contaminated soil. Among them, spectral induced polarization (SIP) has emerged as a promising tool for the identification of contamination due to its sensitivity to the chemistry of pore water, solid-fluid interfaces and fluid content. Previous works have investigated the influences of oil on the electrical signatures of porous media, which demonstrated the potentials of SIP in the detection of hydrocarbon contamination. However, few works have done on the SIP response of oil in clayey soils. In this study, we perform a set of SIP measurements on the clayey samples under different water saturations. These clayey soils are characterized by relatively high cation exchange capacity. The objective in this work is to test the empirical relationships between the three exponents, including the cementation exponent (m), the saturation exponent (n) and the quadrature conductivity exponent (p), which is expected to reduce the model parameters needed in geophysical and hydraulic properties predictions. Our results show that the complex conductivity are saturation dependent. The magnitude of both in-phase and quadrature conductivities generally decrease with decreasing water saturation. The shape of quadrature conductivity spectra slightly changes when water saturation decreases in some cases. The saturation exponent slightly increases with cation exchange capacity, specific surface area and clay content, with an average value around 2.05. Compared to saturation exponent, the quadrature conductivity exponent apparently increases with cation exchange capacity and specific surface area while has little to do with the clay content. Further, the results indicate that the quadrature conductivity exponent p does not strictly obey to p=n-1 as proposed by Vinegar and Waxman (1984). Instead, it mostly ranges between p=n-1.5 and p=n-0

  16. 76 FR 72005 - NUREG-1556, Volume 2, Revision 1, “Consolidated Guidance About Materials Licenses Program...

    Science.gov (United States)

    2011-11-21

    ... Herrera, Division of Materials Safety and State Agreements, Office of Federal and State Materials and Environmental Management Programs, telephone (301) 415-7138, email: Tomas.Herrera@nrc.gov . NRC's Public Web...

  17. Characterisation of weathered clayey soils responsible for shallow landslides

    Directory of Open Access Journals (Sweden)

    C. Meisina

    2006-01-01

    Full Text Available Shallow earth translational slides and earth flows, affecting colluvial soils derived by the weathering of the clayey bedrock, are a recurrent problem causing damage to buildings and roads in many areas of Apennines. The susceptibility assessment, e.g. slope stability models, requires the preliminary characterization of these superficial covers (lithology, geotechnical and hydraulic parameters. The aim of the work is to develop and test a methodology for the identification and mapping of weathered clayey soils responsible for shallow landslides. A test site in Northern Apennines (Province of Pavia was selected. Argillaceous and marly successions characterize the area. Shallow landslides occurred periodically due to high intensity rainfalls. Trench pits were used for the soil profile description (lithology, structure, grade of weathering, thickness and sampling. The main geological, topographic and geomorphologic parameters of shallow landslides were analysed. Field surveys were integrated with some geotechnical laboratory tests (index properties, suction and volumetric characteristic determination, methylene blue adsorption test, linear shrinkage, swell strain. Engineering geological zoning was carried out by grouping the superficial soils on the basis of the following attributes: topographic conditions (slope angle, landslide occurrence, lithology (grain size, geometry (thickness, lithology of the bedrock, hydrogeological and geotechnical characteristics. The resulting engineering-geological units (areas that may be regarded as homogeneous from the geomorphologic and engineering – geological point of view were analysed in terms of shallow slope instability.

  18. Stabilization of soft clayey soils with sawdust ashes

    Directory of Open Access Journals (Sweden)

    Karim Hussein

    2018-01-01

    Full Text Available The problems of soft clayey soils are taken in considerations by many Iraqi geologists and civil engineers, because about 35% of the Iraqi clay soils (especially southern Iraq are weak. Thus, it is necessary to improve the properties of such soils for road construction by means of using of various stabilizers such as sawdust ash. The main goal of the present study is to stabilize soft clay models with sawdust ash (SDA additive using different percentages (0, 2, 4, 6, 8 and 10% by dry weight of soil. The results revealed that the additive has adverse effects on the property of soil indices by increasing its liquid limit and plasticity index due to clay content. The mixture of sawdust ashes with soft clay soils improves most other physical and mechanical properties of the soil, as expressed by a general reduction in specific gravity and maximum dry density (MDD, as well as a reduction in the compression coefficients (Cc and Cr with an increase in SDA content. While increasing the optimum moisture content (OMC and the undrained shear strength (cu with the increase in SDA content. The stabilized soils (with 4 and 10% ash content resulted in low CBR values (1.6-1.2% which can be used as sub-base. The SDA can be considered as a cheap and acceptable stabilizing agent in road construction for improving most of the geotechnical properties of the soft clayey soil.

  19. Caoxite-hydroxyapatite composition as consolidating material for the chalk stone from Basarabi-Murfatlar churches ensemble

    Science.gov (United States)

    Ion, Rodica-Mariana; Turcanu-Caruţiu, Daniela; Fierăscu, Radu-Claudiu; Fierăscu, Irina; Bunghez, Ioana-Raluca; Ion, Mihaela-Lucia; Teodorescu, Sofia; Vasilievici, Gabriel; Rădiţoiu, Valentin

    2015-12-01

    The development of new composition for surface conservation of some architectural monuments represents now an important research topic. The Basarabi-Murfatlar Ensemble, recognized as the first religious monument from mediaeval Dobrogea (Romania) (from 9th to 11th century), is one of the most impressive archaeological sites of Europe. This ensemble is built from amorphous calcium carbonate, very sensitive to humidity, frost, salts, etc. The aim of this paper is to test on chalk stone samples a new consolidant - hydroxyapatite (HAp) mixed with calcium oxalate trihydrate (caoxite) (COT). Some specific techniques for evaluation its impact on chalk stone surface are used, as follows: petrographical and physical-chemical techniques: SEM, OM, ICP-AES, TGA, FTIR and Raman spectroscopy, chromatic parameters changes, the accelerated weathering tests: heating, freeze-thaw, and their effects on porosity and capillary water uptake by the chalk surface. All these have been evaluated before and after treatment with COT-HAp, putting into evidence the effect of the new composition on the chalk stone surface. HAp induces COT stabilization, and their joint composition can bind weathered stone blocks providing a substantial reinforcement of chalk surface.

  20. Shear-Rate-Dependent Behavior of Clayey Bimaterial Interfaces at Landslide Stress Levels

    Science.gov (United States)

    Scaringi, Gianvito; Hu, Wei; Xu, Qiang; Huang, Runqiu

    2018-01-01

    The behavior of reactivated and first-failure landslides after large displacements is controlled by the available shear resistance in a shear zone and/or along slip surfaces, such as a soil-bedrock interface. Among the factors influencing the resistance parameter, the dependence on the shear rate can trigger catastrophic evolution (rate-weakening) or exert a slow-down feedback (rate-strengthening) upon stress perturbation. We present ring-shear test results, performed under various normal stresses and shear rates, on clayey soils from a landslide shear zone, on its parent lithology and other lithologies, and on clay-rock interface samples. We find that depending on the materials in contact, the normal stress, and the stress history, the shear-rate-dependent behaviors differ. We discuss possible models and underlying mechanisms for the time-dependent behavior of landslides in clay soils.

  1. Assessing PAH removal from clayey soil by means of electro-osmosis and electrodialysis

    DEFF Research Database (Denmark)

    Lima, Ana T.; Ottosen, Lisbeth M.; Heister, Katja

    2012-01-01

    Polycyclic aromatic hydrocarbons (PAH) are persistent and toxic contaminants which are difficult to remove from fine porous material like clayey soils. The present work aims at studying two electroremediation techniques for the removal of PAHs from a spiked natural silt soil from Saudi Arabia...... and a silty loam soil from The Netherlands which has been exposed to tar contamination for over 100years. The two techniques at focus are electro-osmosis and electrodialysis. The latter is applied for the first time for the removal of PAH. The efficiency of the techniques is studied using these two soils......, having been subjected to different PAH contact times.Two surfactants were used: the non-ionic surfactant Tween 80 and anionic surfactant sodium dodecyl sulphate (SDS) to aid desorption of PAHs from the soil. Results show a large discrepancy in the removal rates between spiked soil and long-term field...

  2. Determination of Matrix Pore Size Distribution in Fractured Clayey Till and Assessment of Matrix Migration of Dechlorinationg Bacteria

    DEFF Research Database (Denmark)

    Cong, Lu; Broholm, Mette Martina; Fabricius, Ida Lykke

    2014-01-01

    The pore structure and pore size distribution (PSD) in the clayey till matrix from three Danish field sites were investigated by image analysis to assess the matrix migration of dechlorinating bacteria in clayey till. Clayey till samples had a wide range of pore sizes, with diameters of 0.1–100 μ...

  3. The Behavior and Durability of Self-Consolidating Concrete.

    Science.gov (United States)

    2015-05-01

    This report focuses on the production of self-consolidating concrete using local materials from Las Vegas, Nevada. Tests were conducted on eight self-consolidating concrete mixtures having two different percentages of fly-ash replacement (25% and 35%...

  4. Environmental assessment for renewal and consolidation of Materials License Nos. SNM-362, SMB-405, 08-00566-05, 08-00566-10, and 08-00566-12 (Docket No. 70-398)

    International Nuclear Information System (INIS)

    1985-03-01

    The proposed action for which this Environmental Assessment is prepared is the renewal and consolidation of five nuclear materials licenses for radiological activities at the National Bureau of Standards (NBS) site. These licenses cover most uses of radioactive material at NBS except that controlled by the license for operation of the NBS reactor. The reactor license is not associated with and will not be affected by the currently proposed licensing action

  5. Removal of PAHs from contaminated clayey soil by means of electro-osmosis

    KAUST Repository

    Lima, Ana T.; Kleingeld, Pieter J.; Heister, Katja; Loch, J.P. Gustav

    2011-01-01

    process that has been used for the mobilization and cleanup of contaminants in clayey soils with varying successes. The present study focuses on the remediation of a contaminated peaty clay soil, located in Olst - the Netherlands, by means of electro

  6. Prototypical Rod Consolidation Demonstration Project

    International Nuclear Information System (INIS)

    1993-05-01

    The objective of Phase III of the Prototypical Rod Consolidation Demonstration Project (PRCDP) was to procure, fabricate, assemble, and test the Prototypical Rod Consolidation System as described in the NUS Phase II Final Design Report. This effort required providing the materials, components, and fabricated parts which makes up all of the system equipment. In addition, it included the assembly, installation, and setup of this equipment at the Cold Test Facility. During the Phase III effort the system was tested on a component, subsystem, and system level. Volume IV provides the Operating and Maintenance Manual for the Prototypical Rod Consolidation System that was installed at the Cold Test Facility. This document, Book 1 of Volume IV, discusses: Process overview functional descriptions; Control system descriptions; Support system descriptions; Maintenance system descriptions; and Process equipment descriptions

  7. Prototypical Rod Consolidation Demonstration Project

    International Nuclear Information System (INIS)

    1993-05-01

    The objective of Phase III of the Prototypical Rod Consolidation Demonstration Project (PRCDP) was to procure, fabricate, assemble, and test the Prototypical Rod Consolidation System as described in the NUS Phase II Final Design Report. This effort required providing the materials, components, and fabricated parts which makes up all of the system equipment. In addition, it included the assembly, installation, and setup of this equipment at the Cold Test Facility. During the Phase III effort the system was tested on a component, subsystem, and system level. Volume IV provides the Operating and Maintenance Manual for the Prototypical Rod Consolidation System that was installed at the Cold Test Facility. This document, Book 4 of Volume IV, discusses: Off-normal operating and recovery procedures; Emergency response procedures; Troubleshooting procedures; and Preventive maintenance procedures

  8. Electro-chemo-hydro-mechanical coupling in clayey media; Couplage electro-chimio-hydro-mecaniques dans les milieux argileux

    Energy Technology Data Exchange (ETDEWEB)

    Lemaire, Th

    2004-12-15

    The aim of this study is to understand coupled phenomena that occur in swelling porous materials like clays. Electro-chemo-hydro-mechanical contributions are taken into account to analyze transfers in such minerals. In a first part, a general discussion is proposed to introduce mineralogical and physico- chemical considerations of clayey media. An important objective of this chapter is to show the crucial role of the microstructure. In a second part is presented an imbibition test in a MX80 bentonite powder. The hydraulic diffusivity versus water content curve's decrease is explained thanks to a double porosity model that shows the progressive collapse of meso-pores due to swelling effects at the micro-scale. Thus a multi-scale analysis is necessary to well describe clayey media behaviour. The third chapter exposes such a multi-scale modelling (periodic homogenization). It is based on the double-layer theory and introduces an innovative concept of virtual electrolyte solution. First numerical results are given in a simple geometry (parallel platelets). In the next part are proposed numerical simulations of two kinds: response of the system to a chemical gradient and simulation of electro-osmosis. The end of this chapter puts into relief the necessity to integrate pH effects in the model. In the last part, chemical surface exchanges are incorporated in the modelling to understand pH and ionic force roles in electro-osmotic process. (author)

  9. Large Strain Analysis of Electro-Osmosis Consolidation for Clays

    NARCIS (Netherlands)

    Yuan, J.

    2015-01-01

    Consolidation of soft clay creates a lot of problems in foundation engineering, because of the very low clay permeability and high compressibility. Primary consolidation takes a long time to complete if the material is left consolidating under atmospheric evaporation, and traditional dewatering

  10. Behaviour of the UO2/clayey water. A spectroscopic approach

    International Nuclear Information System (INIS)

    Guilbert, S.

    2000-05-01

    This work deals with the disposal of spent nuclear fuels in deep geological layers. After three years of irradiation, these fuels are constituted of 95 % UO 2 . It is then indispensable to know the leaching behaviour of this solid because ground waters are the main agents of dispersion to biosphere of the radioelements contained in these fuels. This work includes alteration tests carried out with a device allowing to synthesize a clayey water equilibrated with a partial pressure in CO 2 in oxidizing or reducing conditions. After the tests, the solid and the solution have been characterized in order to establish a balance of the alteration. The UO 2 matrix has been characterized by XPS. The uranium in solution has been titrated by ICP-MS. In oxidizing conditions, after some weeks, the dissolution velocity of UO 2 has stabilized around 3*10 11 mol/m 2 .s. This velocity is of 4*10 12 mol/m 2 .s in a reducing medium. The uranium concentrations in the oxidized water are of about 2*10 4 mol/l after two years of leaching. After 33 days of alteration in a reducing medium, the uranium amount is of 3*10 6 mol/l. The XPS technique has revealed a superficial and progressive oxidation of the uranium(IV) and the formation of U-OH bonds in the oxidizing medium. A U(VI)/U(IV) ratio has been determined by this technique. It has stabilized around 2 in some weeks. In reducing conditions, this ratio is stable and is of about 0.5. Modeling tools have allowed to propose a class of solids potentially able to control the uranium solubility. In oxidizing conditions, the uranyl hydrates (schoepite) evolve towards uranyl silicates which are thermodynamically more stable. In reducing conditions, a control of the uranium concentration in solution by U 4 O 9 is probable. (O.M.)

  11. Specific heat capacities of different clayey samples obtained by differential scanning calorimetry

    International Nuclear Information System (INIS)

    Fernandez, A.M.

    2012-01-01

    Document available in extended abstract form only. The thermo-physical properties allow to calculate heat flows and to determine the thermal behaviour of the materials. Temperature influences the rates of the physical, chemical and biological reactions and processes in the soil or a material. Variations in temperature and water content in thermal, hydraulic, mechanical and geochemical processes affect the thermal properties such as density, specific heat, thermal conductivity and thermal diffusivity. Therefore, mathematical models that describe the dependence of the thermal properties on temperature and concentration are of interest to be used in computational programs applied to the modelling of coupled thermo-mechanical-hydraulic and chemical (THMC) processes. In this work, the specific heat capacity of different clayey international reference materials was determined. Differential Scanning Calorimetry (DSC) was used for such purpose. DSC is the main tool for determining the specific heat capacities of materials as a function of temperature. The specific heat capacity, c p (J/Kg.K), is a measurement of the amount of heat required to raise the temperature of a unit mass of a substance by one unit of temperature. A change in temperature, caused by a gain or a loss of heat from a material, depends on the specific heat capacity of the material. Thus, the specific heat capacity is a key and characteristic property of a material and/or substance, which should be determine accurately. The specific heat capacity is an intensive property and, unlike the thermal conductivity and thermal diffusivity, is independent of the dry density of the material. C p of the solid samples was determined by using a SETSYS Evolution 16 thermal analyser coupled to a differential scanning calorimeter (TG-DSC-DTA) from SETARAM Instrumentation. The thermal analyser system can use a heating rate from 0.01 to 100 C/min under a dynamic argon atmosphere and temperatures ranging from ambient to

  12. THE POTENTIAL OF γ-RAY SPECTROSCOPY FOR SOIL PROXIMAL SURVEY IN CLAYEY SOILS

    Directory of Open Access Journals (Sweden)

    Simone Priori

    2014-01-01

    Full Text Available Gamma-ray spectroscopy surveys the intensity and distribution of γ-rays emitted from radionuclides of soils and bedrocks. The most important radionuclides of soils and rocks are: 40K, 232Th, 238U and 137Cs, the latter due to Chernobyl burst or radioactive pollution. Distribution and quantity of these radionuclides into the soil is strictly linked to parent material mineralogy and soil cation exchange capacity. The aim of this work is to show the makings of γ-ray spectroscopy proximal survey within experimental fields with clayey soils in western Sicily.The γ-ray spectrometer used for the fieldwork was “The Mole”, made by “The Soil Company”, “Medusa system” and the University of Groningen, from The Netherlands. During the survey of eight experimental fields, 55 soil samples were collected for laboratory analysis of particle size distribution, calcium carbonate, organic carbon and total nitrogen content. The results of the work showed the statistical correlations between soil features and γ-ray data. 

  13. Assessing PAH removal from clayey soil by means of electro-osmosis and electrodialysis

    KAUST Repository

    Lima, Ana T.

    2012-10-01

    Polycyclic aromatic hydrocarbons (PAH) are persistent and toxic contaminants which are difficult to remove from fine porous material like clayey soils. The present work aims at studying two electroremediation techniques for the removal of PAHs from a spiked natural silt soil from Saudi Arabia and a silty loam soil from The Netherlands which has been exposed to tar contamination for over 100. years. The two techniques at focus are electro-osmosis and electrodialysis. The latter is applied for the first time for the removal of PAH. The efficiency of the techniques is studied using these two soils, having been subjected to different PAH contact times. Two surfactants were used: the non-ionic surfactant Tween 80 and anionic surfactant sodium dodecyl sulphate (SDS) to aid desorption of PAHs from the soil. Results show a large discrepancy in the removal rates between spiked soil and long-term field contaminated soil, as expected. In spiked soil, electro-osmosis achieves up to 85% while electrodialysis accomplishes 68% PAH removal. In field contaminated soil, electro-osmosis results in 35% PAH removal whereas electrodialysis results in 79%. Short recommendations are derived for the up-scale of the two techniques. © 2012.

  14. Assessing PAH removal from clayey soil by means of electro-osmosis and electrodialysis

    KAUST Repository

    Lima, Ana T.; Ottosen, Lisbeth M.; Heister, Katja; Loch, J.P. Gustav

    2012-01-01

    Polycyclic aromatic hydrocarbons (PAH) are persistent and toxic contaminants which are difficult to remove from fine porous material like clayey soils. The present work aims at studying two electroremediation techniques for the removal of PAHs from a spiked natural silt soil from Saudi Arabia and a silty loam soil from The Netherlands which has been exposed to tar contamination for over 100. years. The two techniques at focus are electro-osmosis and electrodialysis. The latter is applied for the first time for the removal of PAH. The efficiency of the techniques is studied using these two soils, having been subjected to different PAH contact times. Two surfactants were used: the non-ionic surfactant Tween 80 and anionic surfactant sodium dodecyl sulphate (SDS) to aid desorption of PAHs from the soil. Results show a large discrepancy in the removal rates between spiked soil and long-term field contaminated soil, as expected. In spiked soil, electro-osmosis achieves up to 85% while electrodialysis accomplishes 68% PAH removal. In field contaminated soil, electro-osmosis results in 35% PAH removal whereas electrodialysis results in 79%. Short recommendations are derived for the up-scale of the two techniques. © 2012.

  15. Prediction of the Effect of Using Stone Column in Clayey Soil on the Behavior of Circular Footing by ANN Model

    Directory of Open Access Journals (Sweden)

    Omar Khaleel Ismael Al-Kubaisi

    2018-05-01

    Full Text Available Shallow foundations are usually used for structures with light to moderate loads where the soil underneath can carry them. In some cases, soil strength and/or other properties are not adequate and require improvement using one of the ground improvement techniques. Stone column is one of the common improvement techniques in which a column of stone is installed vertically in clayey soils. Stone columns are usually used to increase soil strength and to accelerate soil consolidation by acting as vertical drains. Many researches have been done to estimate the behavior of the improved soil. However, none of them considered the effect of stone column geometry on the behavior of the circular footing. In this research, finite element models have been conducted to evaluate the behavior of a circular footing with different stone column configurations. Moreover, an Artificial Neural Network (ANN model has been generated for predicting these effects. The results showed a reduction in the bending moment, the settlement, and the vertical stresses with the increment of the stone column length, while both the horizontal stress and the shear force were increased. ANN model showed a good relationship between the predicted and the calculated results.

  16. About the identification of behaviour law parameters of clayey rocks

    International Nuclear Information System (INIS)

    Lecampion, B.

    2002-09-01

    This work aims at developing identification methods for clayey rock parameters. These methods are necessary for the interpretation of the numerous data obtained at the ANDRA's Meuse/Haute-Marne underground laboratory. Two main rheological aspects have been considered: the poro-elastic behaviour and the elasto-visco-plastic behaviour. The first part of the study focusses on the poro-elastic parameters. Chapter 2 recalls the direct problem and discusses some important points of the identification inverse problem. Chapter 3 deals with the formulation of gradient calculation techniques for the linear poro-elastic case. The resolution using the finite-element method is discussed. The direct and associated state differentiation methods are validated for a 2D numerical example using the finite-element code Cast3M. The identification of poro-elastic coefficients of the Meuse/Haute-Marne argillaceous rocks is discussed in detail in chapter 4. The use of approximate semi-explicit solutions of the direct problems allows to obtain a fast identification method. The second part deals with the identification of elasto-visco-plastic parameters. The visco-plastic behaviour of Meuse/Haute-Marne rocks is discussed in chapter 5 and a visco-plastic model with nonlinear isotropic cold-drawing is proposed which allows to reproduce the tests. The parameters of this behaviour law are identified on a 1D creep test in drained conditions. Thus, the delayed deformations come from the poro-elastic and visco-plastic behaviour of the rock. It is shown that both phenomena can be separated. All poro-elasto-visco-plastic parameters are identified and a semi-explicit solution of the creep test is used. Chapter 6 presents an identification method of the elasto-visco-plastic parameters for the general case. The identification is equivalent to the minimization of a cost functional. The gradient of the functional is calculated by direct differentiation. The direct differentiation method is developed in

  17. Consolidation of renders and plasters

    Czech Academy of Sciences Publication Activity Database

    van Hees, R.; Veiga, R.; Slížková, Zuzana

    2017-01-01

    Roč. 50, č. 1 (2017), s. 50-65 ISSN 1359-5997 R&D Projects: GA MŠk(CZ) LO1219 Keywords : consolidants * plasters * requirements * selection * assessment Subject RIV: AL - Art, Architecture, Cultural Heritage OBOR OECD: Materials engineering Impact factor: 2.607, year: 2016 http://link.springer.com/article/10.1617/s11527-016-0894-5

  18. Characterization of waste products prepared from radioactive contaminated clayey soil cemented according to the GEODUR process

    International Nuclear Information System (INIS)

    Brodersen, K.; Vinther, A.

    1990-11-01

    Radioactive contaminated soil may arise due to accidents of various types or may be detected during decommisioning of nuclear installations. Ordinary surface soil cannot normally be conditioned using conventional cementation processes since the content of humic materials retards or prevents the solidification. An additive available from the Danish firm Geodur A/S makes it possible to circumvent this difficulty and to produce a monolithic, nondusting waste type using rather small amounts of cement. The report describes work on characterization of such a cemented waste product prepared on basis of clayey top soil from the Risoe area. The claimed advantages of the process was verified, and data for the compression strength (low), hydraulic conductivity (satisfactory) and other pore structure-related properties are given for the obtained products. Unfortunately the behaviour of cesium and strontium, representing two of the most relevant radionuclides, was not too promising. The retention of cesium is satisfactory, but less good than for the untreated soil. Greatly improved cesium retention after drying of the materials was noticed. Good retention of strontium is only obtained after reaction of the material with carbon dioxide from the atmosphere. The behaviour of the two isotopes in other types of cemented waste is somewhat similar, but the decrease in retention compared with untreated soil makes the process less interesting as a possibility for remedial actions after accidents, etc. Some further studies of the cemented soil waste are beeing made within the frame of the Nordic Nuclear Safety Studies. Elements forming low solublity components in the high pH environment in the cemented soil will probably be retained quite efficiently. This was demonstrated in case of Zn. (author) 11 tabs., 22 ills., 8 refs

  19. High-energy high-rate pulsed-power processing of materials by powder consolidation and by railgun deposition. Technical report (Final), 10 April 1985-10 February 1987

    Energy Technology Data Exchange (ETDEWEB)

    Persad, C.; Marcus, H.L.; Weldon, W.F.

    1987-03-31

    This exploratory research program was initiated to investigate the potential of using pulse power sources for powder consolidation, deposition and other high-energy high-rate processing. The characteristics of the high-energy-high-rate (1MJ/s) powder consolidation using megampere current pulses from a homopolar generator, were defined. Molybdenum Alloy TZM, a nickel-based metallic glass, copper/graphite composites, and P/M aluminum alloy X7091 were investigated. The powder-consolidation process produced high densification rates. Density values of 80% to 99% could be obtained with subsecond high-temperature exposure. Specific energy input and applied pressure were controlling process parameters. Time temperature transformation (TTT) concepts underpin a fundamental understanding of pulsed power processing. Inherent control of energy input, and time-to-peak processing temperature developed to be held to short times. Deposition experiments were conducted using an exploding-foil device (EFD) providing an armature feed to railgun mounted in a vacuum chamber. The material to be deposited - in plasma, gas, liquid, or solid state - was accelerated electromagnetically in the railgun and deposited on a substrate. Deposits of a wide variety of single- and multi-specie materials were produced on several types of substrates. In a series of ancillary experiments, pulsed-skin-effect heating and self quenching of metallic conductors was discovered to be a new means of surface modification by high-energy high-rate-processing.

  20. Distribution center consolidation games

    NARCIS (Netherlands)

    Klijn, F.; Slikker, M.

    2005-01-01

    We study a location-inventory model to analyze the impact of consolidation of distribution centers on facility and inventory costs. We introduce a cooperative game and show that when demand processes are i.i.d. the core is non-empty, i.e., consolidation allows for a stable division of the minimal

  1. Prototypical Rod Consolidation Demonstration Project

    International Nuclear Information System (INIS)

    1993-05-01

    The objective of Phase 3 of the Prototypical Rod consolidation Demonstration Project (PRCDP) was to procure, fabricate, assemble, and test the Prototypical Rod consolidation System as described in the NUS Phase 2 Final Design Report. This effort required providing the materials, components, and fabricated parts which makes up all of the system equipment. In addition, it included the assembly, installation, and setup of this equipment at the Cold Test Facility. During the Phase 3 effort the system was tested on a component, subsystem, and system level. This volume 1, discusses the PRCDP Phase 3 Test Program that was conducted by the HALLIBURTON NUS Environmental Corporation under contract AC07-86ID12651 with the United States Department of Energy. This document, Volume 1, Book 2 discusses the following topics: Fuel Rod Extraction System Test Results and Analysis Reports and Clamping Table Test Results and Analysis Reports

  2. Prototypical Rod Consolidation Demonstration Project

    International Nuclear Information System (INIS)

    1993-05-01

    The objective of Phase 3 of the Prototypical Rod consolidation Demonstration Project (PRCDP) was to procure, fabricate, assemble, and test the Prototypical Rod consolidation System as described in the NUS Phase 2 Final Design Report. This effort required providing the materials, components, and fabricated parts which makes up all of the system equipment. In addition, it included the assembly, installation, and setup of this equipment at the Cold Test Facility. During the Phase 3 effort the system was tested on a component, subsystem, and system level. This volume 1, discusses the PRCDP Phase 3 Test Program that was conducted by the HALLIBURTON NUS Environmental Corporation under contract AC07-86ID12651 with the United States Department of Energy. This document, Volume 1, Book 1 discusses the following topics: the background of the project; test program description; summary of tests and test results; problem evaluation; functional requirements confirmation; recommendations; and completed test documentation for tests performed in Phase 3

  3. Prototypical Rod Consolidation Demonstration Project

    International Nuclear Information System (INIS)

    1993-05-01

    The objective of Phase 3 of the Prototypical Rod consolidation Demonstration Project (PRCDP) was to procure, fabricate, assemble, and test the Prototypical Rod consolidation System as described in the NUS Phase 2 Final Design Report. This effort required providing the materials, components, and fabricated parts which makes up all of the system equipment. In addition, it included the assembly, installation, and setup of this equipment at the Cold Test Facility. During the Phase 3 effort the system was tested on a component, subsystem, and system level. This volume 1, discusses the PRCDP Phase 3 Test Program that was conducted by the HALLIBURTON NUS Environmental Corporation under contract AC07-86ID12651 with the United States Department of Energy. This document, Volume 1, Book 9 discusses the following topics: Integrated System Normal Operations Test Results and Analysis Report; Integrated System Off-Normal Operations Test Results and Analysis Report; and Integrated System Maintenance Operations Test Results and Analysis Report

  4. Prototypical Rod Consolidation Demonstration Project

    International Nuclear Information System (INIS)

    1993-05-01

    The objective of Phase 3 of the Prototypical Rod consolidation Demonstration Project (PRCDP) was to procure, fabricate, assemble, and test the Prototypical Rod consolidation System as described in the NUS Phase 2 Final Design Report. This effort required providing the materials, components, and fabricated parts which makes up all of the system equipment. In addition, it included the assembly, installation, and setup of this equipment at the Cold Test Facility. During the Phase 3 effort the system was tested on a component, subsystem, and system level. This volume 1, discusses the PRCDP Phase 3 Test Program that was conducted by the HALLIBURTON NUS Environmental Corporation under contract AC07-86ID12651 with the United States Department of Energy. This document, Volume 1, Book 8 discusses Control System SOT Tests Results and Analysis Report. This is a continuation of Book 7

  5. Dry Rod Consolidation Technology Project results

    International Nuclear Information System (INIS)

    Mullen, C.K.; Feldman, E.M; Vinjamuri, K.; Griebenow, B.L.; Lynch, R.J.; Arave, A.E.; Hill, R.C.

    1988-01-01

    The Dry Rod Consolidation Technology (DRCT) Project conducted at the Idaho National Engineering Laboratory (INEL), in 1987 demonstrated the technical feasibility of a dry horizontal fuel rod consolidation process. Fuel rods from Westinghouse 15 /times/ 15 pressurized water reactor (PWR) spent fuel assemblies were consolidated into canisters to achieve a 2:1 volume reduction ratio. The consolidation equipment was operated at an existing hot cell complex at the INEL. The equipment was specifically designed to interface with the existing facility fuel handling and operational capabilities and was instrumented to provide data collection for process technology research. During the operational phase, data were collected from observation of the consolidation process, fuel assembly handling, and fuel rod behavior and characteristics. Equipment performance was recorded and data measurements were compiled on crud and contamination generated and spread. Fuel assembly skeletons [non-fuel bearing components (NFBC)] were gamma scanned and analyzed for isotopic content and profile. The above data collection was enhanced by extensive photograph and video documentation. The loaded consolidation fuel canisters were utilized for a test of the Transnuclear, Inc. TN-24P dry storage cask with consolidated fuel. The NFBC material was stored for a future volume reduction demonstration project. 14 figs., 4 tabs

  6. Consolidating NASA's Arc Jets

    Science.gov (United States)

    Balboni, John A.; Gokcen, Tahir; Hui, Frank C. L.; Graube, Peter; Morrissey, Patricia; Lewis, Ronald

    2015-01-01

    The paper describes the consolidation of NASA's high powered arc-jet testing at a single location. The existing plasma arc-jet wind tunnels located at the Johnson Space Center were relocated to Ames Research Center while maintaining NASA's technical capability to ground-test thermal protection system materials under simulated atmospheric entry convective heating. The testing conditions at JSC were reproduced and successfully demonstrated at ARC through close collaboration between the two centers. New equipment was installed at Ames to provide test gases of pure nitrogen mixed with pure oxygen, and for future nitrogen-carbon dioxide mixtures. A new control system was custom designed, installed and tested. Tests demonstrated the capability of the 10 MW constricted-segmented arc heater at Ames meets the requirements of the major customer, NASA's Orion program. Solutions from an advanced computational fluid dynamics code were used to aid in characterizing the properties of the plasma stream and the surface environment on the calorimeters in the supersonic flow stream produced by the arc heater.

  7. Organic matter and hydrogen as electron donor for SRB and IRB activities in a clayey medium

    International Nuclear Information System (INIS)

    Chautard, C.; Mifsud, A.; Libert, M.; Marsal, F.

    2012-01-01

    Document available in extended abstract form only. According to the French concept for the disposal of High-Level radioactive Waste (HLW), waste will be emplaced in an environment with multiple metallic components into a geological clay formation. The presence of microorganisms has recently been evidenced in deep clayey environment. Therefore, neither the introduction of microbial species during the construction and operational phases nor the survival of bacteria after the disposal closure can be excluded. Indeed, microbial species may be able to tolerate specific environment with few nutrients to sustain life under high temperature, dry and highly radioactive conditions. Moreover, despite the low porosity of clays, cracks in the excavated disturbed zone and remaining void spaces between disposal components may be favorable for bacterial growth. Sulfate-Reducing Bacteria (SRB) and Iron-Reducing Bacteria (IRB) activities are notably expected to influence iron-clay reactivity, including corrosion processes. Their potential development must be investigated in order to better assess their metabolism, which may in turn influence the evolution of metallic and clayey materials involved in a HLW disposal cell. More specifically, deep geological environments containing low amounts of biodegradable Organic Matter (OM) are generally nutrient poor for microbial development. However, the radiolysis of pore water and the corrosion of metallic components of HLW disposal cell in anoxic conditions will lead to the production of hydrogen, which may also be used as an electron donor for microbial activity. Thus, the purpose of the present work is to quantify the potential of bacterial growth stimulation due either to the production of hydrogen or the presence of OM. In a first step, characterization of DOM leached from Tournemire clay powder has been performed in order to identify and estimate the concentration of soluble organic matter available for bacteria activity which will

  8. Consolidated Lunar Atlas

    Data.gov (United States)

    National Aeronautics and Space Administration — The Consolidated Lunar Atlas is a collection of the best photographic images of the moon, including low-oblique photography, full-moon photography, and tabular and...

  9. Laboratory investigation of steam transmission in unsaturated clayey soil under osmotic potential

    Directory of Open Access Journals (Sweden)

    Mehdi Jalili

    2017-01-01

    Full Text Available Liquids coming from different sources like wastewaters, agricultural and industrial activities and leakages of chemical substances often have high concentration of chemical compositions and the osmotic gradient generated around such sources causes a considerable transmission of the Contamination. The steam transmitted by non-polluted soils moves to polluted masses, causing an increase in the volume of pollution zone and movement of pollutants. Therefore, such physical and chemical processes should be taken into account in pollution transmission models. Using Crumb method, laboratory investigations were conducted on non-dispersive and dispersive clayey soil samples obtained from three areas in Zanjan Province of Iran. A simple experimental setup has been used and hereby introduced. The impact of osmotic force from salinities of 0.5, 1, and 1.5% on steam transmission in clayey soil was examined. Results indicate that for all samples between 5 to 15 days, the moisture content increased in the pollutant zone and decreased in the non-pollutant area. Also it was observed that for dispersive clayey soil, movement of steam among layers was observed to be orderly and its amount was higher than that of non-dispersive clayey soil.

  10. Sorption of chlorinated solvents and degradation products on natural clayey tills

    DEFF Research Database (Denmark)

    Cong, Lu; Bjerg, Poul Løgstrup; Zhang, Fengjun

    2011-01-01

    linear, but fitted by Freundlich isotherms slightly better over the entire concentration range. For chloroethylenes, tetrachloroethylene (PCE) was most strongly sorbed to the clayey till samples (Kd=0.84–2.45Lkg−1), followed by trichloroethylene (TCE, Kd=0.62–0.96Lkg−1), cis-dichloroethylene (cis-DCE, Kd...

  11. Assessment of geotechnical properties of uncemented/cemented clayey soil incorporated with waste crumb rubber

    Directory of Open Access Journals (Sweden)

    JITENDRA SINGH YADAV

    2017-03-01

    Full Text Available Discarded waste tires are becoming a serious threat to health, environment, and ecological systems worldwide if it is not disposed of properly. Every year 1000 million of waste tires are discarded. This number may grow up to 1200 million by the year 2030. On the other hand, construction of civil engineering structures such as buildings, dams, highways, etc. are at high risk of differential settlement, especially in the case of weak or soft clay, which is due to its low shear strength and high compressibility. The paper aims to assess geotechnical properties of uncemented/cemented clayey soil incorporated with waste crumb rubber. Compaction parameters, unconfined compressive strength, split tensile strength, toughness index, CBR values and swelling pressure of rubberized uncemented/cemented clayey soil (3%, and 6% cement and different percentage of crumb rubber have been obtained. After rigorous extensive study, it has been concluded that unconfined compressive strength and split tensile strength of rubberized cemented clayey soil decreases with the increase of the percentage of crumb rubber whereas the axial, and diametral strain are found to be increased with the addition of crumb rubber up to 5% after that it starts to decrease. The CBR values, swelling pressure, and toughness index of uncemented/cemented clayey soil was significantly affected by incorporation of crumb rubber. SEM studies have also been incorporated in this investigation.

  12. Improvement of clayey soil characteristics by using activated carbon

    Directory of Open Access Journals (Sweden)

    Al-Soudany Kawther

    2018-01-01

    Full Text Available The clay soil is weak and unable to carry the applied loads as a result of the weight of buildings or vehicles on the load performing on the soil. In this research, clay soil was grained and mixed with different percentages of activated carbon additives to investigate its performance. One type of clay soil from Al-Taji city was used. The percentages of activated carbon 3, 5, 7 and 9% were added to the soil and the influence of the admixture was observed by comparing the results with the untreated soil. The selected properties for this comparison were specific gravity, consistency limits, compaction, static compaction, CBR, consolidation, swelling and unconfined compressive strength. The results showed that the plasticity index, maximum dry weight and specific gravity decreased as the percentage of additives increased. The unconfined compressive strength increased as the percentage of additives and curing periods (1, 7, 14 and 28days increased. The amount of increase in soil strength was even more than 100% for the 9% activatedcarbon. The results showed that the addition of activated carbon has a positive effect to the geotechnical properties.

  13. Centralized consolidation/recycling center

    International Nuclear Information System (INIS)

    St. Georges, L.T.; Poor, A.D.

    1995-05-01

    There are approximately 175 separate locations on the Hanford Site where dangerous waste is accumulated in hundreds of containers according to compatibility. Materials that are designated as waste could be kept from entering the waste stream by establishing collection points for these materials and wastes and then transporting them to a centralized consolidation/recycling center (hereinafter referred to as the consolidation center). Once there the materials would be prepared for offsite recycling. This document discusses the removal of batteries, partially full aerosol cans, and DOP light ballasts from the traditional waste management approach, which eliminates 89 satellite accumulation areas from the Hanford Site (43 for batteries, 33 for aerosols, and 13 for DOP ballasts). Eliminating these 89 satellite accumulation areas would reduce by hundreds the total number of containers shipped offsite as hazardous waste (due to the increase in containers when the wastes that are accumulated are segregated according to compatibility for final shipment). This new approach is in line with the U.S. Environmental Protection Agency's (EPA) draft Universal Waste Rules for these open-quotes nuisanceclose quotes and common waste streams. Additionally, future reviews of other types of wastes that can be handled in this less restrictive and more cost-effective manner will occur as part of daily operations at the consolidation center. The Hanford Site has been identified as a laboratory for reinventing government by the Secretary of the U.S. Department of Energy (DOE), Hazel O'Leary, and as a demonstration zone where open-quotes innovative ideas, processes and technologies can be created, tested and demonstrated.close quotes Additionally, DOE, EPA, and the Washington State Department of Ecology (Ecology) have agreed to cut Hanford cleanup costs by $1 billion over a 5-year period

  14. Geotechnical Properties of Clayey Soil Stabilized with Cement ...

    African Journals Online (AJOL)

    ADOWIE PERE

    2017-12-31

    Dec 31, 2017 ... ... to investigate the different effects of cement-sawdust ash and cement on a ... Keywords: Cement, Saw dust, strength test subgrade material, highway construction ... characteristics of lateritic soil stabilized with sawdust ash.

  15. Effects of Consolidation Stress State on Normally Consolidated Clay

    DEFF Research Database (Denmark)

    Lade, Poul V.

    2000-01-01

    The effect of consolidation stress state on the stress-strain and strength characteristics has been studied from experiments on undisturbed block samples of a natural, normally consolidated clay known as San Francisco Bay Mud. The results of experiments on K0-consolidated, hollow cylinder specimens...... and on isotropically consolidated, cubical specimens, both tested in triaxial compression and extension, clearly showed the influence of the undisturbed fabric as well as the effect of the initial consolidation stress states. While the K0-consolidated specimens appeared to retain their original fabric and exhibit...

  16. Schemas and memory consolidation.

    Science.gov (United States)

    Tse, Dorothy; Langston, Rosamund F; Kakeyama, Masaki; Bethus, Ingrid; Spooner, Patrick A; Wood, Emma R; Witter, Menno P; Morris, Richard G M

    2007-04-06

    Memory encoding occurs rapidly, but the consolidation of memory in the neocortex has long been held to be a more gradual process. We now report, however, that systems consolidation can occur extremely quickly if an associative "schema" into which new information is incorporated has previously been created. In experiments using a hippocampal-dependent paired-associate task for rats, the memory of flavor-place associations became persistent over time as a putative neocortical schema gradually developed. New traces, trained for only one trial, then became assimilated and rapidly hippocampal-independent. Schemas also played a causal role in the creation of lasting associative memory representations during one-trial learning. The concept of neocortical schemas may unite psychological accounts of knowledge structures with neurobiological theories of systems memory consolidation.

  17. Stabilisation of clayey soils with high calcium fly ash and cement

    Energy Technology Data Exchange (ETDEWEB)

    S. Kolias; V. Kasselouri-Rigopoulou; A. Karahalios [National Technical University of Athens, Athens (Greece)

    2005-02-01

    The effectiveness of using high calcium fly ash and cement in stabilising fine-grained clayey soils (CL,CH) was investigated in the laboratory. Strength tests in uniaxial compression, in indirect (splitting) tension and flexure were carried out on samples to which various percentages of fly ash and cement had been added. Modulus of elasticity was determined at 90 days with different types of load application and 90-day soaked CBR values are also reported. Pavement structures incorporating subgrades improved by in situ stabilisation with fly ash and cement were analyzed for construction traffic and for operating traffic. These pavements are compared with conventional flexible pavements without improved subgrades and the results clearly show the technical benefits of stabilising clayey soils with fly ash and cement. In addition TG-SDTA and XRD tests were carried out on certain samples in order to study the hydraulic compounds, which were formed.

  18. IMPACT OF A USED STABILISER ON THE CALIFORNIA BEARING RATIO OF THE CLAYEY-SANDY SILT

    Directory of Open Access Journals (Sweden)

    Katarzyna Kamińska

    2017-01-01

    Full Text Available The paper aimed at the determination of the California Bearing Ratio of a stabilised and unstabilised fine-grained mineral soil. A clayey-sandy silt with the addition of 3, 6 and 10% of road stabilisers Solidex and Solidex A was used for the tests. The tests were carried out in the press Tritech 50 at the loading of 22 and 44 N. The stabilised samples were subjected to 7-days treatment, whereas unstabilised 4-days treatment. Stabilization with the applied road binders brought positive effects, there occurred a significant improvement in the mechanical properties of the clayey-sandy silt. The better binder, which significantly increased the value of the CBR ratio, was Solidex A. The use of hydraulic binders is of a great importance in road building, because their addition improves the mechanical properties of weaker mineral soils.

  19. Laboratory assessment of the influence of the proportion of waste foundry sand on the geotechnical engineering properties of clayey soils

    CSIR Research Space (South Africa)

    Mgangira, Martin B

    2006-01-01

    Full Text Available Soil improvement can be achieved through mechanical stabilisation using industrial byproducts. Clayey soils were blended with waste foundry sand to examine its influence on the geotechnical engineering properties of the soils. The waste foundry sand...

  20. An Investigation for Disposal of Drill Cuttings into Unconsolidated Sandstones and Clayey Sands

    Energy Technology Data Exchange (ETDEWEB)

    Mese, Ali; Dvorkin, Jack; Shillinglaw, John

    2000-09-11

    This project include experimental data and a set of models for relating elastic moduli/porosity/texture and static-to-dynamic moduli to strength and failure relationships for unconsolidated sands and clayey sands. The results of the project should provide the industry with a basis for wider use of oil base drilling fluids in water sensitive formations by implementing drill cutting injection into existing wells at abandoned formations and controlling fracture geometry to prevent ground water contamination.

  1. Flow dynamics at the origin of thin clayey sand lacustrine turbidites: Examples from Lake Hazar, Turkey

    KAUST Repository

    Hage, Sophie

    2017-04-18

    Turbidity currents and their deposits can be investigated using several methods, i.e. direct monitoring, physical and numerical modelling, sediment cores and outcrops. The present study focuses on thin clayey sand turbidites found in Lake Hazar (Turkey) occurring in eleven clusters of closely spaced thin beds. Depositional processes and sources for three of those eleven clusters are studied at three coring sites. Bathymetrical data and seismic reflection profiles are used to understand the specific geomorphology of each site. X-ray, thin sections and CT-scans imagery combined with grain-size, geochemical and mineralogical measurements on the cores allow characterisation of the turbidites. Turbidites included in each cluster were produced by remobilization of surficial slope sediment, a process identified in very few studies worldwide. Three types of turbidites are distinguished and compared with deposits obtained in flume studies published in the literature. Type 1 is made of an ungraded clayey silt layer issued from a cohesive flow. Type 2 is composed of a partially graded clayey sand layer overlain by a mud cap, attributed to a transitional flow. Type 3 corresponds to a graded clayey sand layer overlain by a mud cap issued from a turbulence-dominated flow. While the published experimental studies show that turbulence is damped by cohesion for low clay content, type 3 deposits of this study show evidence for a turbulence dominated mechanism despite their high clay content. This divergence may in part relate to input variables such as water chemistry and clay mineralogy that are not routinely considered in experimental studies. Furthermore, the large sedimentological variety observed in the turbidites from one coring site to another is related to the evolution of a sediment flow within a field scale basin made of a complex physiography that cannot be tackled by flume experiments.

  2. Consolidating Financial Statements.

    Science.gov (United States)

    Wood, Marcia R.

    This publication is designed to be a desktop reference and assist financial officers in both public and independent institutions of higher education in the preparation of consolidated financial statements. Chapter 1 covers generally accepted accounting principles and other accounting literature, and summarizes reporting rules of the Financial…

  3. Cyclic behavior of self-consolidated concrete.

    Science.gov (United States)

    2014-08-01

    This reports highlights on the production of Self-Consolidating concrete using local materials from Las Vegas, Nevada. 4 SCC : mixtures were worked on with 2 different levels of FA replacement and the inclusion of superplasticizers, ADVA 195 and V-MA...

  4. Consolidation modelling for thermoplastic composites forming simulation

    Science.gov (United States)

    Xiong, H.; Rusanov, A.; Hamila, N.; Boisse, P.

    2016-10-01

    Pre-impregnated thermoplastic composites are widely used in the aerospace industry for their excellent mechanical properties, Thermoforming thermoplastic prepregs is a fast manufacturing process, the automotive industry has shown increasing interest in this manufacturing processes, in which the reconsolidation is an essential stage. The model of intimate contact is investigated as the consolidation model, compression experiments have been launched to identify the material parameters, several numerical tests show the influents of the temperature and pressure applied during processing. Finally, a new solid-shell prismatic element has been presented for the simulation of consolidation step in the thermoplastic composites forming process.

  5. Contribution to the study of cementitious and clayey materials behaviour in the context of deep geological disposal: transport aspect, durability and thermo-hydro-mechanical behaviour; Contribution a l'etude du comportement des materiaux cimentaires et argileux en vue de leur utilisation dans le contexte du stockage geologique profond: aspect transport, durabilite et comportement thermo-hydro-mecanique

    Energy Technology Data Exchange (ETDEWEB)

    Galle, C.

    2011-07-15

    Deep geological formation disposal is the reference solution in France for the management of medium and high activities radioactive waste. In this context, to demonstrate the feasibility of such a disposal, it is necessary to evaluate the long-term performances and the behaviour of the materials engaged in the elaboration of engineered barrier systems (EBS) and waste package elements. The studies mentioned and synthesized in this HDR thesis focused mainly on the convective transport of gas (under pressure gradient) in cementitious matrices, by coupling microstructure aspect (porosity/pores sizes distribution) and hydric environment (water saturation). Works on physico-chemical durability allowed the description of the chemical degradation of cement-based materials in extreme conditions using ammonium nitrate, to increase the materials damaging processes in order to identify functional margins. In relationship with the interim storage management phase, studies related to the behaviour and characterization of concrete submitted to high temperatures (up to 400 C) were also described. Finally, results concerning the gas (H{sub 2}) overpressure resistance of engineered barriers made of compacted clays were summarized. (author)

  6. Effective elasticity coefficients of native rocks and consolidated granular matter

    International Nuclear Information System (INIS)

    Schulz, Beatrix M.; Schulz, Michael

    2008-01-01

    The elastic coefficients of binary heterogeneous materials, such as several native rock materials or consolidated granular matter will be determined in terms of a perturbation expansion. Furthermore, in order to check the validity of the obtained results, these are compared with numerical investigations using Boole's model of randomly distributed spheres. Finally, we apply the results on several classes of native rocks and consolidated granular materials

  7. Nonlinear Finite Strain Consolidation Analysis with Secondary Consolidation Behavior

    Directory of Open Access Journals (Sweden)

    Jieqing Huang

    2014-01-01

    Full Text Available This paper aims to analyze nonlinear finite strain consolidation with secondary consolidation behavior. On the basis of some assumptions about the secondary consolidation behavior, the continuity equation of pore water in Gibson’s consolidation theory is modified. Taking the nonlinear compressibility and nonlinear permeability of soils into consideration, the governing equation for finite strain consolidation analysis is derived. Based on the experimental data of Hangzhou soft clay samples, the new governing equation is solved with the finite element method. Afterwards, the calculation results of this new method and other two methods are compared. It can be found that Gibson’s method may underestimate the excess pore water pressure during primary consolidation. The new method which takes the secondary consolidation behavior, the nonlinear compressibility, and nonlinear permeability of soils into consideration can precisely estimate the settlement rate and the final settlement of Hangzhou soft clay sample.

  8. Prototypical Rod Consolidation Demonstration Project

    International Nuclear Information System (INIS)

    1993-05-01

    The objective of Phase 3 of the Prototypical Rod consolidation Demonstration Project (PRCDP) was to procure, fabricate, assemble, and test the Prototypical Rod consolidation System as described in the NUS Phase 2 Final Design Report. This effort required providing the materials, components, and fabricated parts which makes up all of the system equipment. In addition, it included the assembly, installation, and setup of this equipment at the Cold Test Facility. During the Phase 3 effort the system was tested on a component, subsystem, and system level. This volume 1, discusses the PRCDP Phase 3 Test Program that was conducted by the HALLIBURTON NUS Environmental Corporation under contract AC07-86ID12651 with the United States Department of Energy. This document, Volume 1, Book 4 discusses the following topics: Rod Compaction/Loading System Test Results and Analysis Report; Waste Collection System Test Results and Analysis Report; Waste Container Transfer Fixture Test Results and Analysis Report; Staging and Cutting Table Test Results and Analysis Report; and Upper Cutting System Test Results and Analysis Report

  9. Prototypical Rod Consolidation Demonstration Project

    International Nuclear Information System (INIS)

    1993-05-01

    The objective of Phase 3 of the Prototypical Rod consolidation Demonstration Project (PRCDP) was to procure, fabricate, assemble, and test the Prototypical Rod consolidation System as described in the NUS Phase 2 Final Design Report. This effort required providing the materials, components, and fabricated parts which makes up all of the system equipment. In addition, it included the assembly, installation, and setup of this equipment at the Cold Test Facility. During the Phase 3 effort the system was tested on a component, subsystem, and system level. This volume 1, discusses the PRCDP Phase 3 Test Program that was conducted by the HALLIBURTON NUS Environmental Corporation under contract AC07-86ID12651 with the United States Department of Energy. This document, Volume 1, Book 5 discusses the following topics: Lower Cutting System Test Results and Analysis Report; NFBC Loading System Test Results and Analysis Report; Robotic Bridge Transporter Test Results and Analysis Report; RM-10A Remotec Manipulator Test Results and Analysis Report; and Manipulator Transporter Test Results and Analysis Report

  10. Use of Waste Marble Dust for Stabilization of Clayey Soil

    Directory of Open Access Journals (Sweden)

    Altug SAYGILI

    2015-11-01

    Full Text Available The main objective of this research is to investigate the possibility of utilizing waste marble dust in stabilizing problematic soils (especially swelling clays. The research work was divided into two sections. The first section deals with the shear strength parameters and swelling characteristics, the second section deals with the microstructural investigation of the improved problematic soils. The marble dust addition ratios which have been studied were 0 %, 5 %, 10 %, 20 % and 30 % by weight. Physical, mechanical and chemical properties of soil and marble dust samples were investigated. In addition, SEM analyses were performed on the specimens. Test results indicate that marble dust addition improved the shear strength parameters and reduced the swell potential of the tested clay samples. Marble dust had a noticeable role in the hydration process because of high calcium content. Obtained results showed that marble dust addition to the clay samples will reduce the cost of constructing structures on problematic soils, and finding new utilization areas for waste marble dust will decrease environmental pollution. Utilizing waste marble dust materials in problematic soils will have great contribution to the economy and conservation of resources.DOI: http://dx.doi.org/10.5755/j01.ms.21.4.11966

  11. Status of rod consolidation

    International Nuclear Information System (INIS)

    Bailey, W.J.

    1985-04-01

    Two of the factors that need to be taken into account with rod consolidation are (1) the effects on rods from their removal from the fuel assembly and (2) the effects on rods as a result of the consolidation process. Potential components of both factors are described in the report. Discussed under (1) are scratches on the fuel rod surfaces, rod breakage, crud, extended burnup, and possible cladding embrittlement due to hydrogen injection at BWRs. Discussed under (2) are the increased water temperature (less than 10 0 C) because of closer packing of the rods, formation of crevices between rods in the close-packed mode, contact with dissimilar metals, and the potential for rapid heating of fuel rods following the loss of water from a spent fuel storage pool. Another factor that plays an important role in rod consolidation is the cost of disposal of the nonfuel-bearing components of the fuel assembly. Also, the dose rate from the components - especially Inconel spacer grids - can affect the handling procedures. Several licensing issues that exist are described. A list of recommendations is provided. 98 refs., 5 figs., 5 tabs

  12. Fate of corrosion products released from stainless steel in marine sediments and seawater. Part 2. Sequim Bay clayey silt

    International Nuclear Information System (INIS)

    Schmidt, R.L.

    1982-04-01

    This report describes laboratory experiments in which neutron-activated 347 stainless steel specimens were exposed to clayey silt from Sequim Bay, Washington. The properties and trace metal geochemistry of the sediment and the amounts of corrosion products that were released under oxic and reduced conditions and their distribution among different chemical fractions of the sediment are discussed. The distributions of Cr, Mn, Fe, Ni and Cu among different chemical forms in the Sequim Bay sediment show that DTPA removed <10% of extractable Cr, Fe and Mn, approx. 20% of extractable Ni and approx. 30% of extractable Cu. The inorganic fraction (material soluble in 2.5% acetic acid) accounted for approx. 30% of total extractable Mn and approx. 10% or less of Cr, Fe, Ni and Cu. Major portions of Cr and Cu, and a large amount of Fe were in the organic fraction. Extractable Mn, Fe and Ni were associated with hydrous oxides likely as coatings on the mineral substrate of the sediment. No Co was detectable in any of the extracts

  13. Investigation of fiber-reinforced self-consolidating concrete.

    Science.gov (United States)

    2010-05-01

    The rising cost of materials and labor, as well as the demand for faster construction, has prompted development of cheaper, faster alternatives to conventional building techniques. Self-consolidating concrete (SCC), a high performance concrete charac...

  14. Self-Consolidating Concrete for Prestressed Bridge Girders

    Science.gov (United States)

    2017-07-01

    This document reports the findings of a research project designed to better understand material and structural performance of prestressed bridge girders made with Self-Consolidating Concrete (SCC) from Wisconsin. SCC has high potential to be used for...

  15. Sand-RAPG combination simulating fertile clayey soil (Part I to IV)

    International Nuclear Information System (INIS)

    Azzam, R.; El-Hady, O.A.; Lotfy, A.A.; Hegela, M.

    1983-01-01

    I. Radiation Preparation of RAPG. Sites of co-ordination and reinforcement are dominated in reclaimer ameliorator polymeric gel (RAPG). It is a modified acrylonitrile base multifunction polymer grafted upon a binder of worthless cellulosic agricultural discard. It varies chemically from non-ionic through anionic and cationic to ampholite. The hydroproperty of the gel is similarly controlled. Thus, RAPG can be tailored for any soil texture under various climatic conditions. II. Structure Stability and Maintenance. Sinai dune sand is treated with non-ionic and anionic RAPGs at rates varying from 0.05 to 0.2 wt.%. The stability increased with RAPG anionicity and application rate. The structure formed maintained three cycles of complete destruction and re-formation without significant changes in erosion index. The resistance of sand-RAPG combination to breakdown by tillage, as well as to wind and water erosion, is practically proved. This is in addition to the beneficial changes in bulk density, void ratio and microporosity, which were also achieved. III. Water Preservation. Inshas sandy soil treated by RAPG is compared with fertile clayey soil. The water-holding capacity and retention at different suctions are increased. The available water to plants in treated sand has reached 15 times that of the control, and even exceeded clay by 11%. Water losses by evaporation and leaching as well as deep percolation are all reduced to a minimum. IV. Plantation and Nutritional Status. Pepper seed germination, growth and dry matter are increased in the sand-RAPG combination relative to fertile clayey soil. The optimum rate and anionicity of RAPG are determined. This increases water-use efficiency to twice that of the fertile clayey soil. Macro- and micro-nutrient uptake have also increased. Thus, fertilizer use efficiency is increased by almost three times over that of clay. These factors lead convincingly to the conclusion that RAPG furnishes adequate conditions for sandy soil

  16. Consolidated fuel reprocessing program

    Science.gov (United States)

    1985-04-01

    A survey of electrochemical methods applications in fuel reprocessing was completed. A dummy fuel assembly shroud was cut using the remotely operated laser disassembly equipment. Operations and engineering efforts have continued to correct equipment operating, software, and procedural problems experienced during the previous uranium compaigns. Fuel cycle options were examined for the liquid metal reactor fuel cycle. In high temperature gas cooled reactor spent fuel studies, preconceptual designs were completed for the concrete storage cask and open field drywell storage concept. These and other tasks operating under the consolidated fuel reprocessing program are examined.

  17. Consolidation of the formation sand by chemical methods

    Directory of Open Access Journals (Sweden)

    Mariana Mihočová

    2006-10-01

    Full Text Available The sand control by consolidation involves the process of injecting chemicals into the naturally unconsolidated formation to provide an in situ grain-to-grain cementation. The sand consolidation chemicals are available for some 30 years. Several types of consolidating material were tried. Presently available systems utilize solidified plastics to provide the cementation. These systems include phenol resin, phenol-formaldehyde, epoxy, furan and phenolic-furfuryl.The sand consolidation with the steam injection is a novel technique. This process provides a highly alkaline liquid phase and temperatures to 300 °C to geochemically create cements by interacting with the dirty sand.While the formation consolidation has widely applied, our experience has proved a high level of success.

  18. Consolidation and Disclosure of SPE

    OpenAIRE

    中野, 貴之

    2011-01-01

    The purpose of this study is to discuss what kinds of information are demanded by the users of financial statements and what kinds of problems plague the companies using SPE (special purpose equity), while considering the actual situations of the consolidation and disclosure of SPE in Japan. At present, there is the trend of consolidating a broad range of SPE in Japan, etc., but some users of financial statements point out that it became difficult to understand consolidated financial stat...

  19. Consolidated Copayment Processing Center (CCPC)

    Data.gov (United States)

    Department of Veterans Affairs — The Consolidated Copayment Processing Center (CCPC) database contains Veteran patient contact and billing information in order to support the printing and mailing of...

  20. On calculating the pressure on cylindrical timbers of vertical shafts in clayey soils

    Energy Technology Data Exchange (ETDEWEB)

    Mizyumskii, V A

    1979-11-01

    In order to calculate the pressure built up on timbers which have been constructed to hold back freely moving soil in a clay environment, a formula is recommended which characterizes the state of clayey soil. The formula incorporates the parameters for volume information, momentary and long displacement modulus, decay factor of deformations of the after effect, viscosity factor in the starting zone of reforming. Because the timber creates a reaction pressure on the contour of the working, the radial travel of the timber is calculated and then the pressure on the timber. Correlation of the calculated pressure with the results of measurements in workings showed that the pressure of clayey soil on the timber is the result of viscous flow deformations. Disregarding these deformations, the pressures on the shaft timbering in the Yuzhno-Belozerskii deposit were calculated at 0.004 and 0.006 tons/m/sup 2/ respectively at a depth of 90 and 142 meters. After reworking the soil and setting up timbering the pressure was calculated at 2/3 of that of the highest measurements. The formula suggested is suitable for determining pressure on timbers having a large creep. (12 refs.) (In Russian)

  1. Consistency based correlations for tailings consolidation

    Energy Technology Data Exchange (ETDEWEB)

    Azam, S.; Paul, A.C. [Regina Univ., Regina, SK (Canada). Environmental Systems Engineering

    2010-07-01

    The extraction of oil, uranium, metals and mineral resources from the earth generates significant amounts of tailings slurry. The tailings are contained in a disposal area with perimeter dykes constructed from the coarser fraction of the slurry. There are many unique challenges pertaining to the management of the containment facilities for several decades beyond mine closure that are a result of the slow settling rates of the fines and the high standing toxic waters. Many tailings dam failures in different parts of the world have been reported to result in significant contaminant releases causing public concern over the conventional practice of tailings disposal. Therefore, in order to reduce and minimize the environmental footprint, the fluid tailings need to undergo efficient consolidation. This paper presented an investigation into the consolidation behaviour of tailings in conjunction with soil consistency that captured physicochemical interactions. The paper discussed the large strain consolidation behaviour (volume compressibility and hydraulic conductivity) of six fine-grained soil slurries based on published data. The paper provided background information on the study and presented the research methodology. The geotechnical index properties of the selected materials were also presented. The large strain consolidation, volume compressibility correlations, and hydraulic conductivity correlations were provided. It was concluded that the normalized void ratio best described volume compressibility whereas liquidity index best explained the hydraulic conductivity. 17 refs., 3 tabs., 4 figs.

  2. Vertical hydraulic conductivity of a clayey-silt aquitard: accelerated fluid flow in a centrifuge permeameter compared with in situ conditions

    Science.gov (United States)

    Timms, W. A.; Crane, R.; Anderson, D. J.; Bouzalakos, S.; Whelan, M.; McGeeney, D.; Rahman, P. F.; Guinea, A.; Acworth, R. I.

    2014-03-01

    Evaluating the possibility of leakage through low permeability geological strata is critically important for sustainable water supplies, extraction of fuels from strata such as coal beds, and confinement of waste within the earth. Characterizing low or negligible flow rates and transport of solutes can require impractically long periods of field or laboratory testing, but is necessary for evaluations over regional areas and over multi-decadal timescales. The current work reports a custom designed centrifuge permeameter (CP) system, which can provide relatively rapid and reliable hydraulic conductivity (K) measurement compared to column permeameter tests at standard gravity (1g). Linear fluid velocity through a low K porous sample is linearly related to g-level during a CP flight unless consolidation or geochemical reactions occur. The CP module is designed to fit within a standard 2 m diameter, geotechnical centrifuge with a capacity for sample dimensions of 30 to 100 mm diameter and 30 to 200 mm in length. At maximum RPM the resultant centrifugal force is equivalent to 550g at base of sample or a total stress of ~2 MPa. K is calculated by measuring influent and effluent volumes. A custom designed mounting system allows minimal disturbance of drill core samples and a centrifugal force that represents realistic in situ stress conditions is applied. Formation fluids were used as influent to limit any shrink-swell phenomena which may alter the resultant K value. Vertical hydraulic conductivity (Kv) results from CP testing of core from the sites in the same clayey silt formation varied (10-7 to 10-9 m s-1, n = 14) but higher than 1g column permeameter tests of adjacent core using deionized water (10-9 to 10-11 m s-1, n = 7). Results at one site were similar to in situ Kv values (3 × 10-9 m s-1) from pore pressure responses within a 30 m clayey sequence in a homogenous area of the formation. Kv sensitivity to sample heterogeneity was observed, and anomalous flow via

  3. The Tosudite, a clayey mineral which marks the uranium-bearing mineralisation in the Arlit area (Niger)

    International Nuclear Information System (INIS)

    Billon, S.; Beaufort, D.; Sardini, P.; Wattinne, A.

    2009-01-01

    The authors report an investigation which aims at the identification of clayey minerals in the sedimentary series of the Tim Mersoi basin in Niger, and of their petrogenetic meaning. Based on spectrometry and on chemical micro-analysis, they identify the different components of the Tosudite present in the clayey phase: a sodoite-type chlorite and a montmorillonite-type smectite. The presence of Tosudite is interpreted as the result of a post-diagenetic episode related to infiltrations of magnesium-based and oxidative solutions. The way the uranium-bearing minerals precipitated suggests that the Tosudite is a marker of a mineralisation episode

  4. Consolidated fuel reprocessing program

    International Nuclear Information System (INIS)

    Kuban, D.P.; Noakes, M.W.; Bradley, E.C.

    1987-01-01

    The Advanced Servomanipulator (ASM) System consists of three major components: the ASM slave, the dual arm master controller or master, and the control system. The ASM is a remotely maintainable force-reflecting servomanipulator developed at the Oak Ridge National Laboratory (ORNL) as part of the Consolidated Fuel Reprocessing Program of (CFRP). This new manipulator addresses requirements of advanced nuclear fuel reprocessing with emphasis on force reflection, remote maintainability, and reliability. It uses an all-gear force transmission system. The master arms were designed as a kinematic replica of ASM and use cable force transmission. Special digital control algorithms were developed to improve the system performance. The system is presently operational and undergoing evaluation. Preliminary testing has been completed and is reported. The system is now undergoing commercialization by transferring the technology to the private sector

  5. Consolidating Social Media Strategies

    DEFF Research Database (Denmark)

    Gyimóthy, Szilvia; Munar, Ana Maria; Larson, Mia

    2014-01-01

    This study revisits and integrates the insights of recent studies on emergent social media strategies deployed by destination and event management organisations. In a comparative analysis Munar (2012) identified four generic approaches pursued by national tourism boards in the Nordic region, while...... Gyimóthy & Larson (2014) portrayed three digital value co-creation strategies deployed by festival social media. Both frameworks provided novel analytical typologies which identified a series of categories (mimetic, analytic, immersion, advertising and insourcing, crowdsourcing and community consolidation......). This paper discusses the complementary nature of these conceptual proposals and advances an integrated conceptual framework of social media strategies. Based on the empirical findings of a case study that revisits evolving digital and social media strategies of European DMOs this paper maps the dynamics...

  6. Consolidated clinical microbiology laboratories.

    Science.gov (United States)

    Sautter, Robert L; Thomson, Richard B

    2015-05-01

    The manner in which medical care is reimbursed in the United States has resulted in significant consolidation in the U.S. health care system. One of the consequences of this has been the development of centralized clinical microbiology laboratories that provide services to patients receiving care in multiple off-site, often remote, locations. Microbiology specimens are unique among clinical specimens in that optimal analysis may require the maintenance of viable organisms. Centralized laboratories may be located hours from patient care settings, and transport conditions need to be such that organism viability can be maintained under a variety of transport conditions. Further, since the provision of rapid results has been shown to enhance patient care, effective and timely means for generating and then reporting the results of clinical microbiology analyses must be in place. In addition, today, increasing numbers of patients are found to have infection caused by pathogens that were either very uncommon in the past or even completely unrecognized. As a result, infectious disease specialists, in particular, are more dependent than ever on access to high-quality diagnostic information from clinical microbiology laboratories. In this point-counterpoint discussion, Robert Sautter, who directs a Charlotte, NC, clinical microbiology laboratory that provides services for a 40-hospital system spread over 3 states in the southeastern United States explains how an integrated clinical microbiology laboratory service has been established in a multihospital system. Richard (Tom) Thomson of the NorthShore University HealthSystem in Evanston, IL, discusses some of the problems and pitfalls associated with large-scale laboratory consolidation. Copyright © 2015, American Society for Microbiology. All Rights Reserved.

  7. Dry rod consolidation technology development

    International Nuclear Information System (INIS)

    Rasmussen, T.L.; Schoonen, D.H.; Feldman, E.M.; Fisher, M.W.

    1987-01-01

    The Department of Energy's (DOE) Office of Civilian Radioactive Waste Management (OCRWM) is funding a program to consolidate commercial spent fuel for testing in dry storage casks and to develop technology that will be fed into other OCRWM programs, e.g., Prototypical Consolidation Demonstration Program (PCDP). The program is being conducted at the Idaho National Engineering Laboratory (INEL) by the INEL Operating Contractor EG and G Idaho, Inc. Hardware and software have been designed and fabricated for installation in a hot cell adjacent to the Test Area North (TAN) Hot Shop Facility. This equipment is used to perform dry consolidation of commercial spent fuel from the Virginia Power (VP) Cooperative Agreement Spent Fuel Storage Cask (SFSC) Demonstration Program and assemblies that had previously been stored at the Engine Maintenance and Disassembly (EMAD) facility in Nevada. Consolidation is accomplished by individual, horizontal rod pulling. A computerized semiautomatic control system with operator involvement is utilized to conduct consolidation operations. During consolidation operations, data is taken to characterize this technology. Still photo, video tape, and other documentation will be generated to make developed information available to interested parties. Cold checkout of the hardware and software was completed in September of 1986. Following installation in the hot cell, consolidation operations begins in May 1987. Resulting consolidated fuel will be utilized in the VP Cooperative Agreement SFSC Program

  8. Dry rod consolidation technology development

    International Nuclear Information System (INIS)

    Rasmussen, T.L.; Schoonen, D.H.; Fisher, M.W.

    1986-01-01

    The Department of Energy's (DOE) Office of Civilian Radioactive Waste Management (OCRWM) is funding a Program to consolidate commercial spent fuel for testing in dry storage casks and to develop technology that will be fed into other OCRWM Programs, e.g., Prototypical Consolidation Demonstration Program. The Program is being conducted at the Idaho National Engineering Laboratory (INEL) by the Operating Contractor, EGandG Idaho, Inc. Hardware and software have been designed and fabricated for installation in a hot cell adjacent to the Test Area North (TAN) Hot Shop Facility. This equipment will be used to perform dry consolidation of commercial spent fuel from the Virginia Power (VP) Cooperative Agreement Spent Fuel Storage Cask (SPSC) Demonstration Program and assemblies that had previously been stored at the Engine Maintenance and Disassembly (EMAD) facility in Nevada. Consolidation will be accomplished by individual, horizontal rod pulling. A computerized semi-automatic control system with operator involvement will be utilized to conduct consolidation operations. Special features have been incorporated in the design to allow crud collection and measurement of rod pulling forces. During consolidation operations, data will be taken to characterize this technology. Still photo, video tape, and other documentation will be generated to make developed information available to interested parties. Cold checkout of the hardware and software will complete in September of 1986. Following installation in the hot cell, consolidation operations will begin in January 1987. Resulting consolidated fuel will be utilized in the VP Cooperative Agreement SFSC Program

  9. The Financial Effects of Consolidation.

    Science.gov (United States)

    Streifel, James S.; And Others

    1991-01-01

    Examination of 19 school district consolidations in 10 states, 1980-84, revealed that, of 6 expenditure categories, only administration showed significant savings 3 years after consolidation, when compared to changes in state average costs during that period. Changes in other expenditure categories varied widely among districts. Contains 22…

  10. Guide to Direct Consolidation Loans.

    Science.gov (United States)

    Department of Education, Washington, DC.

    Intended for financial aid counselors, this document provides guidelines to the Federal Direct Consolidation Loan Program for borrowers who are in school, as well as those in repayment, or in default. An introductory section explains the basics of the consolidated loan program, loan categories, and interest rates. Next, standards for borrower…

  11. District Consolidation: Rivals Coming Together

    Science.gov (United States)

    Mart, Dan

    2011-01-01

    District consolidation is a highly emotional process. One key to success is sticking to the facts. In Iowa, school districts facing financial difficulties or enrollment concerns do not have to move directly to consolidation. In many cases, districts begin by developing sharing agreements. These sharing agreements may start with simple sharing of…

  12. SOME DISCLOSURE ASPECTS REGARDING CONSOLIDATED FINANCIAL STATEMENTS

    Directory of Open Access Journals (Sweden)

    Cirstea Andreea

    2013-07-01

    Full Text Available The purpose of this article is to analyze the current state of consolidated reporting practice harmonization concerning the choice of presenting the income statement, the changes in equity, the methods used for presenting the cash flow statement, the extant methods for evaluating and reporting goodwill, the extant methods in which jointly controlled entities are accounted in the consolidated financial statements, or the choice for recognizing investments in subsidiaries, jointly controlled entities and associates in the separate statements of the parent company. In order to achieve our goal we selected the first 10 groups, in order of their capitalization value, that were listed on each of the following capital markets: London Stock Exchange, NYSE Euronext (Paris Stock Exchange and Deutsche Börse (Frankfurt Stock Exchange and we analyzed, in a qualitative and in a quantitative manner, for a period of six years starting with 2007, their consolidated financial statements with the design to establish exactly which of the aspects stated in the International Financial Reporting Standards were being used for the items presented above. In order to complete the empirical research part of the paper that addresses from a comparative perspective the evaluation of the degree of material harmony between the reporting practices of groups listed on the three stock exchanges above-mentioned, we used statistical and mathematical methods represented by the I Index first described by Van der Tas. Taking into account the fact that since 2005 all listed companies on the European stock exchanges were required to adopt the international accounting standards for their consolidated financial disclosures, the degree of material harmony was studied only in reference to those requirements that presented two methods or possibilities of disclosure.Our findings suggest that the groups analyzed present a high degree of material harmonization with respect to the reporting

  13. Long-term monitoring of nitrate transport to drainage from three agricultural clayey till fields

    Science.gov (United States)

    Ernstsen, V.; Olsen, P.; Rosenbom, A. E.

    2015-08-01

    The application of nitrogen (N) fertilisers to crops grown on tile-drained fields is required to sustain most modern crop production, but it poses a risk to the aquatic environment since tile drains facilitate rapid transport pathways with no significant reduction in nitrate. To maintain the water quality of the aquatic environment and the provision of food from highly efficient agriculture in line with the EU's Water Framework Directive and Nitrates Directive, field-scale knowledge is essential for introducing water management actions on-field or off-field and producing an optimal differentiated N-regulation in future. This study strives to provide such knowledge by evaluating on 11 years of nitrate-N concentration measurements in drainage from three subsurface-drained clayey till fields (1.3-2.3 ha) representing approximately 71 % of the surface sediments in Denmark dominated by clay. The fields differ in their inherent hydrogeological field settings (e.g. soil-type, geology, climate, drainage and groundwater table) and the agricultural management of the fields (e.g. crop type, type of N fertilisers and agricultural practices). The evaluation revealed three types of clayey till fields characterised by: (i) low net precipitation, high concentration of nitrate-N, and short-term low intensity drainage at air temperatures often below 5 °C; (ii) medium net precipitation, medium concentration of nitrate-N, and short-term medium-intensity drainage at air temperatures often above 5 °C; and (iii) high net precipitation, low concentration of nitrate-N and long-term high intensity drainage at air temperatures above 5 °C. For each type, on-field water management actions, such as the selection of crop types and introduction of catch crops, appeared relevant, whereas off-field actions only seemed relevant for the latter two field types given the temperature-dependent reduction potential of nitrate off-field. This initial well-documented field-scale knowledge from fields

  14. Modifying the consolidation depth of nanolime on Maastricht limestone

    Czech Academy of Sciences Publication Activity Database

    Niedoba, Krzysztof; Slížková, Zuzana; Frankeová, Dita; Nunes, Cristiana Lara; Jandejsek, Ivan

    2017-01-01

    Roč. 133, February (2017), s. 51-56 ISSN 0950-0618 R&D Projects: GA MŠk(CZ) LO1219 Keywords : stone consolidation * calcium hydroxide nanoparticles * CaLoSiL * X-ray radiography * drilling resistance * consolidant distribution Subject RIV: AL - Art, Architecture, Cultural Heritage OBOR OECD: Materials engineering Impact factor: 3.169, year: 2016 http://www.sciencedirect.com/science/article/pii/S0950061816317664

  15. Study on extraction of uranium from clayey sandstone with floatation-leaching process

    International Nuclear Information System (INIS)

    Meng Guangshou; Zhao Manchang; Wu Peisheng; Song Wenlan; Li Wenxia.

    1985-01-01

    An improved floatation-leaching process is proposed to extract uranium from some clayey sandstone type of ore. By two-step flotation, the ground feed ore can be divided into three urani-ferous sections, i.e., the sulfidic concentrate carrying organic matter, the carbonate concentrate, and the tailings. The sulfidic concentrate is mixed with the tailings and then treated by acid-leaching with the result that 93% uranium extraction can be attained. The excess free acid of the leached slurry is further neutralized with the carbonate concentrate instead of lime commonly used. As a result, approximately 60% uranium extraction can be attained. As a whole, by the flotation-leaching process the acid consumption can be reduced from 200 kg/t down to < 80 kg/t and the uranium extraction can be raised from 85% to 90% as compared with the conventional acid-leaching process

  16. Instrumental neutron activation analysis (INAA) of some clayey rocks of Poland

    International Nuclear Information System (INIS)

    Janczyszyn, J.; Domanska, G.; Wyszomirski, P.

    1988-01-01

    The instrumental neutron activation analysis (INAA) was applied for determination of minor and trace element contents in some Polish clayey rocks. Lower Silesian kaolins from Wyszonowice near Strzelin and from Wadroze Wielkie near Legnica as well as allite from Kaplonosy (Lublin Coal Basin) were investigated. The contents of 26 elements were determined, including rare earth metals (Sc, La, Ce, Nd, Sm, Eu, Tb, Yb, Lu), actinides (U, Th), alkali metals (Na, K, Rb, Cs) and gold. INAA studies allowed to determine the variability of minor and trace element contents in the weathering profile in 2,5/K borehole in Wyszonowice and in size fractions separated from kaolin of Wadroze Wielkie. When using this method, the effectiveness of chemical and thermal extraction of these elements from allite of Kaplonosy was checked, too. (author)

  17. Removal of PAH using electrokinetic transport of biosurfactants in clayey soil

    Energy Technology Data Exchange (ETDEWEB)

    Maria, E.; Lin, J. [Dept. of Building Civil and Environmental Engineering, Concordia Univ., Montreal (Canada)

    2001-07-01

    The electrokinetic introduction of non-toxic, biodegradable surfactants (produced ex-situ) to remediate PAH-contaminated soil was investigated. The lab tests demonstrated the possibility of removal of organic contaminants from clayey soil without hazardous impact to the environment. The rhamnolipids (biosurfactants), produced by Pseudomonas aeruginosa to increase the solubility of PAHs into the aqueous phase, were used in the enhancement of electrokinetic remediation. This study determined the potential on-site production of biosurfactants that was directly introduced to soil by means of electrokinetics. The average removal of phenanthrene achieved 74% in the presence of biosurfactants above CMC. The remaining compounds are left for biodegradation. These results contribute to the development of a new remediation technology - bioelectrokinetics. (orig.)

  18. Halloysite Nanotubes for Cleaning, Consolidation and Protection.

    Science.gov (United States)

    Cavallaro, Giuseppe; Lazzara, Giuseppe; Milioto, Stefana; Parisi, Filippo

    2018-01-10

    Herein, we report our recent research concerning the development of halloysite based protocols for cleaning, consolidation and protection purposes. Surface modification of halloysite cavity by anionic surfactants was explored to fabricate inorganic micelles able to solubilize hydrophobic contaminants. Hybrid dispersions based on halloysite and ecocompatible polymers were tested as consolidants for paper and waterlogged archaeological woods. Encapsulation of deacidifying and flame retardant agents within the halloysite lumen was conducted with aim to obtain nanofiller with a long-term protection ability. The results prove the suitability and versatility of halloysite nanotubes, which are perspective inorganic nanoparticles within materials science, remedation and conservation of cultural heritage fields. © 2018 The Chemical Society of Japan & Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

  19. NMR study of nanophase Al/Al-oxide powder and consolidated composites

    International Nuclear Information System (INIS)

    Suits, B.H.; Apte, P.; Wilken, D.E.; Siegel, R.W.

    1994-10-01

    27 Al Nuclear Magnetic Resonance (NMR) measurements from aluminum powders and consolidated nanophase aluminum made from those powders are presented. The signals from the metal and surface oxidation are easily separated and are compared before and after consolidation. The results presented indicate that the oxide coating becomes the interface region within the nanophase composite material and that during consolidation the metal has undergone a deformation equivalent to that seen for bulk material under a compressive strain of between 4% and 8%

  20. Consolidated Financial Statements

    OpenAIRE

    Kolářová, Pavla

    2014-01-01

    Diplomová práce se zabývá problematikou konsolidace účetní závěrky. Práce je členěna na dvě části. První část je zaměřena na sestavení konsolidované účetní závěrky za českou část skupiny podniků. Druhá část se zabývá analýzou výkonnosti sestavené konsolidované účetní závěrky a jednotlivých společností finančními ukazateli. Práce rovněž obsahuje návrhy na zlepšení ekonomické situace holdingu či jednotlivých společností. Master's thesis deals with the consolidation of the financial statement...

  1. Effect of the Callovian-Oxfordian clayey fraction on borosilicate glass alteration

    International Nuclear Information System (INIS)

    Debure, M.; Frugier, P.; GIN, S.; De Windt, L.; Michau, N.

    2012-01-01

    Document available in extended abstract form only. In France, high-level nuclear waste (HLW) is confined in a glass matrix packaged into stainless steel canister and carbon steel overpack. The HLW should be buried in a geological clay formation like, potentially, the Callovian-Oxfordian (COx) clay-stone located in the north-eastern Parisian basin. The COx clay-stone contains minerals that can feed the near-field with soluble Mg. Such minerals are carbonates (ankerite, dolomite) as well as clay minerals (chlorite, illite, interstratified illite/smectite). Previous laboratory experiments have proved that aqueous solutions of Mg salts could significantly increase the alteration rate of nuclear glass (Jollivet et al., 2012). This motivated to go a step further by studying the alteration of nuclear glass put in contact with Mg minerals. A first set of experiments have revealed that the rate of glass dissolution was increased with hydro-magnesite (4MgCO 3 .Mg(OH) 2 .4H 2 O, a chemically simple model mineral) and dolomite. In both cases, Mg coming from carbonate dissolution reacts with Si, provided by the glass, in order to form Mg silicates (Debure et al., 2012). In that case, Si consumption sustains glass alteration. Mg silicate precipitation also consumes protons; therefore the interdiffusion of alkali within the glass alteration layer eventually becomes a driving force that sustains Mg silicate precipitation. The second set of experiments, presented here, aimed at better characterizing the role of the COx clayey fraction. The separation of the clayey phases of the COx clay-stone has been made in collaboration with the LEM lab (Nancy, France) by a sequence of sieving, acidic dissolution of carbonates, NaCl washing and sedimentation (Rivard, 2011). According to XRD and infrared analyses, the clayey fraction was mainly composed of kaolinite, illite, interstratified illite/smectite and chlorite (plus a little residual amount of quartz). This first step aimed to remove

  2. Self-consolidating concrete homogeneity

    Directory of Open Access Journals (Sweden)

    Jarque, J. C.

    2007-08-01

    Full Text Available Concrete instability may lead to the non-uniform distribution of its properties. The homogeneity of self-consolidating concrete in vertically cast members was therefore explored in this study, analyzing both resistance to segregation and pore structure uniformity. To this end, two series of concretes were prepared, self-consolidating and traditional vibrated materials, with different w/c ratios and types of cement. The results showed that selfconsolidating concretes exhibit high resistance to segregation, albeit slightly lower than found in the traditional mixtures. The pore structure in the former, however, tended to be slightly more uniform, probably as a result of less intense bleeding. Such concretes are also characterized by greater bulk density, lower porosity and smaller mean pore size, which translates into a higher resistance to pressurized water. For pore diameters of over about 0.5 μm, however, the pore size distribution was found to be similar to the distribution in traditional concretes, with similar absorption rates.En este trabajo se estudia la homogeneidad de los hormigones autocompactantes en piezas hormigonadas verticalmente, determinando su resistencia a la segregación y la uniformidad de su estructura porosa, dado que la pérdida de estabilidad de una mezcla puede conducir a una distribución no uniforme de sus propiedades. Para ello se han fabricado dos tipos de hormigones, uno autocompactante y otro tradicional vibrado, con diferentes relaciones a/c y distintos tipos de cemento. Los resultados ponen de manifiesto que los hormigones autocompactantes presentan una buena resistencia a la segregación, aunque algo menor que la registrada en los hormigones tradicionales. A pesar de ello, su estructura porosa tiende a ser ligeramente más uniforme, debido probablemente a un menor sangrado. Asimismo, presentan una mayor densidad aparente, una menor porosidad y un menor tamaño medio de poro, lo que les confiere mejores

  3. Definition and Classification of the Stakeholders in Land Consolidation Project

    Institute of Scientific and Technical Information of China (English)

    LIU Xiang-dong; GUO Bi-jun; GUO Mao-xuan

    2012-01-01

    Using the methods of questionnaire survey, statistical analysis and multidimensional rating, we define and classify the stakeholders in land consolidation project. 25 kinds of stakeholders are determined, divided into three categories: core stakeholders, including county-level government, county-level land departments, county-level land consolidation center, the rural collective economic organizations, farmers, township government, and the villagers’ committee; middle stakeholders, including central government, the Ministry of Land and Resources, the Ministry of Land and Resources Land Consolidation Center, the provincial land departments, the provincial land consolidation center, the county-level finance departments, the county-level water resources departments, the government supervisory departments, government audit departments, and the public; peripheral stakeholders, including the county-level environmental protection departments, the county-level agricultural departments, supervisory agencies, design agencies, project contractors, equipment suppliers, material suppliers, and the bidding agencies. The project managers should pay attention to the interest appeal of the stakeholders, and adopt different coping strategies.

  4. CONSOLIDATED FINANCIAL STATEMENTS UNDER IFRS

    OpenAIRE

    Tănase Alin-Eliodor; Calotă Traian-Ovidiu

    2013-01-01

    This article is focuses on accounting consolidation techniques and the preparation of consolidation worksheets for the components of financial statements (statement of comprehensive income, statement of changes in equity, and financial position). The presented group includes parent company, two subsidiaries (only one fully controlled by the parent company) and a jointly controlled entity. The financial statements are presented under the following standards IFRS 3 Business Combination, IAS 27 ...

  5. INEL integrated spent nuclear fuel consolidation task team report

    International Nuclear Information System (INIS)

    Henry, R.N.; Clark, J.H.; Chipman, N.A.

    1994-01-01

    This document describes a draft plan and schedule to consolidate spent nuclear fuel (SNF) and special nuclear material (SNW) from aging storage facilities throughout the Idaho National Engineering Laboratory (INEL) to the Idaho Chemical Processing Plant (ICPP) in a safe, cost-effective, and expedient manner. A fully integrated and resource-loaded schedule was developed to achieve consolidation as soon as possible. All of the INEL SNF and SNM management task, projects, and related activities from fiscal year 1994 to the end of the consolidation period are logic-tied and integrated with each other. The schedule and plan are presented to initiate discussion of their implementation, which is expected to generate alternate concepts that can be evaluated using the methodology described in this report. Three perturbations to consolidating SNF as soon as possible are also explored. If the schedule is executed as proposed, the new and on-going consolidation activities will require about 6 years to complete and about $25.3M of additional funding. Reduced annual operating costs are expected to recover the additional investment in about 6.4 years. The total consolidation program as proposed will cost about $66.8M and require about 6 years to recover via reduced operating costs from retired SNF/SNM storage facilities. Detailed schedules and cost estimates for the Test Reactor Area Materials Test Reactor canal transfers are included as an example of the level of detail that is typical of the entire schedule (see Appendix D). The remaining work packages for each of the INEL SNF consolidation transfers are summarized in this document. Detailed cost and resource information is available upon request for any of the SNF consolidation transfers

  6. Influence of prepreg characteristics on stamp consolidation

    Science.gov (United States)

    Slange, T. K.; Warnet, L. L.; Grouve, W. J. B.; Akkerman, R.

    2017-10-01

    Stamp forming is a rapid manufacturing technology used to shape flat blanks of thermoplastic composite material into three-dimensional components. The development of automated lay-up technologies further extends the applicability of stamp forming by allowing rapid lay-up of tailored blanks and partial preconsolidation. This partial preconsolidation makes the influence of prepreg more critical compared to conventional preconsolidation methods which provide full preconsolidation. This paper aims to highlight consolidation challenges that can appear when stamp forming blanks manufactured by automated lay-up. Important prepreg characteristics were identified based on an experimental study where a comparison was made between various prepreg in their as-received, deconsolidated and stamp consolidated state. It was found that adding up small thickness variations across the width of a prepreg when stacking plies into a blank by automated lay-up can cause non-uniform consolidation. Additionally, deconsolidation of the prepreg does not seem to obstruct interlaminar bonding, while intralaminar voids initially present in a prepreg cannot be removed during stamp forming. An additional preconsolidation step after automated lay-up seems necessary to remove blank thickness variations and intralaminar voids for the current prepregs. Eliminating this process step and the successful combination of rapid automated lay-up and stamp forming requires prepregs which are void-free and have less thickness variation.

  7. Tantalum powder consolidation, modeling and properties

    International Nuclear Information System (INIS)

    Bingert, S.R.; Vargas, V.D.; Sheinberg, H.C.

    1996-01-01

    A systematic approach was taken to investigate the consolidation of tantalum powders. The effects of sinter time, temperature and ramp rate; hot isostatic pressing (HIP) temperature and time; and powder oxygen content on consolidation density, kinetics, microstructure, crystallographic texture, and mechanical properties have been evaluated. In general, higher temperatures and longer hold times resulted in higher density compacts with larger grain sizes for both sintering and HIP'ing. HIP'ed compacts were consistently higher in density than sintered products. The higher oxygen content powders resulted in finer grained, higher density HIP'ed products than the low oxygen powders. Texture analysis showed that the isostatically processed powder products demonstrated a near random texture. This resulted in isotropic properties in the final product. Mechanical testing results showed that the HIP'ed powder products had consistently higher flow stresses than conventionally produced plates, and the sintered compacts were comparable to the plate material. A micromechanics model (Ashby HIP model) has been employed to predict the mechanisms active in the consolidation processes of cold isostatic pressing (CIP), HIP and sintering. This model also predicts the density of the end product and whether grain growth should be expected under the applied processing conditions

  8. Microstructural analysis of clayey ceramic incorporated with fluorescent lamp glass; Analise microestrutural de ceramica vermelha incorporada com vidro de lampada fluorescente

    Energy Technology Data Exchange (ETDEWEB)

    Morais, A.S.C.; Caldas, T.C.C.; Pereira, P.S.; Monteiro, S.N.; Vieira, C.M.F., E-mail: allinescmorais@yahoo.com.br [Universidade Estadual do Norte Fluminense Darcy Ribeiro (LAMAV/UENF), Campos dos Goytacazes, RJ (Brazil). Laboratorio de Materiais Avancados

    2011-07-01

    This study aims to evaluate the effect of the incorporation of glass powder fluorescent lamp, from a decontamination process, in the microstructure of clayey ceramic. Formulations were prepared with incorporation of the waste in amounts of up to 10 wt.% into the clayey body. Specimens were prepared by uniaxial mold-press at 20 MPa and then fired at 850 and 1050°C. After firing, the microstructure of the ceramics was evaluated by optical microscopy (OM), scanning electron microscopy (SEM) and X-ray diffraction (XRD). The results showed that the incorporation of glass powder into the clayey body changes the microstructure of the ceramics. (author)

  9. 75 FR 32555 - Consolidated Audit Trail

    Science.gov (United States)

    2010-06-08

    ... Part II Securities and Exchange Commission 17 CFR Part 242 Consolidated Audit Trail; Proposed Rule... 3235-AK51 Consolidated Audit Trail AGENCY: Securities and Exchange Commission. ACTION: Proposed rule... a consolidated order tracking system, or consolidated audit trail, with respect to the trading of...

  10. Simultaneous consolidation and creep

    DEFF Research Database (Denmark)

    Krogsbøll, Anette

    1997-01-01

    Materials that exhibit creep under constant effective stress typically also show rate dependent behavior. The creep deformations and the rate sensitive behavior is very important when engineering and geological problems with large time scales are considered. When stress induced compaction...

  11. Nonnuclear Consolidation Environmental Assessment

    International Nuclear Information System (INIS)

    1993-06-01

    The Department of Energy (DOE) is developing a proposal, known as Complex 21, to reconfigure the Nation's Nuclear Weapons Complex (Complex). The complex is a set of interrelated facilities that design, manufacture, test, and maintain this country's nuclear weapons. The Complex also produces and/or recycles the nuclear materials used in building weapons and stores nuclear materials for future use. DOE also dismantles the weapons retired from the stockpile. In addition, DOE conducts surveillance and maintenance activities to ensure the reliability and safety of the stockpiled weapons throughout their operational life

  12. A consolidated and standardized relational database for ER data

    International Nuclear Information System (INIS)

    Zygmunt, B.C.

    1995-01-01

    The three US Department of Energy (DOE) installations on the Oak Ridge Reservation (ORR) (Oak Ridge National Laboratory, Y-12, and K-25) were established during World War II as part of the Manhattan Project that ''built the bomb.'' That research, and work in more recent years, has resulted in the generation of radioactive materials and other toxic wastes. Lockheed Martin Energy Systems manages the three Oak Ridge installations (as well as the Environmental Restoration (ER) programs at the DOE plants in Portsmouth, Ohio, and Paducah, Kentucky). DOE Oak Ridge Operations has been mandated by federal and state agreements to provide a consolidated repository of environmental data and is tasked to support environmental data management activities at all five installations. The Oak Ridge Environmental Information System (OREIS) was initiated to fulfill these requirements. The primary use of OREIS data is to provide access to project results by regulators. A secondary use is to serve as background data for other projects. This paper discusses the benefits of a consolidated and standardized database; reasons for resistance to the consolidation of data; implementing a consolidated database, including attempts at standardization, deciding what to include in the consolidated database, establishing lists of valid values, and addressing quality control (QC) issues; and the evolution of a consolidated database, which includes developing and training a user community, dealing with configuration control issues, and incorporating historical data. OREIS is used to illustrate these topics

  13. Tomographic findings of lobar consolidation in primary pulmonary tuberculosis

    International Nuclear Information System (INIS)

    Pereira, Bruno Alberto Falcao; Macedo, Solange Goncalves David de; Penna, Claudia Renata Rezende

    2009-01-01

    Objective: To describe tomographic findings of lobar consolidation as early manifestation of primary pulmonary tuberculosis. Materials and methods: The present study was developed at Hospital Municipal Jesus, Rio de Janeiro, RJ, Brazil, in the period between 2002 and 2006, retrospectively evaluating tomographic findings in four children aged from 3 to 14 months with lobar consolidation as an early manifestation of primary pulmonary tuberculosis. Results: The most frequently found radiological pattern was lobar consolidation with calcifications, cavitation and intermingle necrotic areas, associated with bulging fissure. Signs of bronchogenic dissemination and lymph node enlargement were observed in all of the four children. Consolidation with a pseudotumor aspect and masslike effect was observed in one case. Conclusion: The cases included in the present study have demonstrated that primary pulmonary tuberculosis manifested as lobar consolidation presents typical tomographic images such as cavitation, hypodense areas and calcifications intermingled with consolidation. The association with lymph node enlargement with central necrosis and signs of bronchogenic dissemination reinforce the diagnosis of tuberculosis. (author)

  14. Status of rod consolidation, 1988

    International Nuclear Information System (INIS)

    Bailey, W.J.

    1989-01-01

    It is estimated that the spent fuel storage pools at some domestic light-water reactors will run out of space before 2003, the year that the US Department of Energy currently predicts it will have a repository available. Of the methods being studied to alleviate the problem, rod consolidation is one of the leading candidates for achieving more efficient use of existing space in spent fuel storage pools. Rod consolidation involves mechanically removing all the fuel rods from the fuel assembly hardware (i.e., the structural components) and placing the fuel rods in a close-packed array in a canister without space grids. A typical goal of rod consolidation systems is to insert the fuel rods from two fuel assemblies into a canister that has the same exterior dimensions as one standard fuel assembly (i.e., to achieve a consolidation or compaction ratio of 2:1) and to compact the nonfuel-bearing structural components from those two fuel assemblies by a factor of 10 to 20. This report provides an overview of the current status of rod consolidation in the United States and a small amount of information on related activities in other countries. 85 refs., 36 figs., 5 tabs

  15. Influence of the incorporation of grog and argillite in a clayey body for production of ceramic paver

    International Nuclear Information System (INIS)

    Scarpini, V.; Pinheiro, R.M.; Monteiro, S.N.; Vieira, C.M.F.

    2011-01-01

    This work has for objective to evaluate the influence argillite and grog addition, obtained from defective bricks fired al low temperatures, into a clayey body for production of ceramic paver. Cylindrical specimens were uniaxial mold-press and then fired at 850 deg C in a laboratory furnace. The evaluated properties were: water absorption, diametral shrinkage and uniaxial compressive strength. The microstructure of the fired ceramics was evaluated electron scanning microscopy. The results showed that the argillite significantly decreased the water absorption and the shrinkage of the clayey body. The grog also decreased the shrinkage, but also decreased the mechanical strength. With respect to the water absorption, the grog not change this property of the composition elaborated with clays and argillite. (author)

  16. Natural Frequencies of Wind Turbines on Monopile Foundations in Clayey Soils

    DEFF Research Database (Denmark)

    Andersen, Lars Vabbersgaard; Vahdatirad, Mohammadjavad; Sichani, Mahdi Teimouri

    2012-01-01

    A comprehensive study is performed on the stiffness of a monopile foundation supporting an offshore wind turbine in undrained, over-consolidated clay having a spatial variation of the soil properties. The undrained shear strength is considered as a stochastic field with increasing mean value over...

  17. Kinetic modelling of a diesel-polluted clayey soil bioremediation process

    Energy Technology Data Exchange (ETDEWEB)

    Fernández, Engracia Lacasa; Merlo, Elena Moliterni [Chemical Engineering Department, Research Institute for Chemical and Environmental Technology (ITQUIMA), University of Castilla La Mancha, 13071 Ciudad Real (Spain); Mayor, Lourdes Rodríguez [National Institute for Hydrogen Research, C/Fernando el Santo, 13500 Puertollano (Spain); Camacho, José Villaseñor, E-mail: jose.villasenor@uclm.es [Chemical Engineering Department, Research Institute for Chemical and Environmental Technology (ITQUIMA), University of Castilla La Mancha, 13071 Ciudad Real (Spain)

    2016-07-01

    A mathematical model is proposed to describe a diesel-polluted clayey soil bioremediation process. The reaction system under study was considered a completely mixed closed batch reactor, which initially contacted a soil matrix polluted with diesel hydrocarbons, an aqueous liquid-specific culture medium and a microbial inoculation. The model coupled the mass transfer phenomena and the distribution of hydrocarbons among four phases (solid, S; water, A; non-aqueous liquid, NAPL; and air, V) with Monod kinetics. In the first step, the model simulating abiotic conditions was used to estimate only the mass transfer coefficients. In the second step, the model including both mass transfer and biodegradation phenomena was used to estimate the biological kinetic and stoichiometric parameters. In both situations, the model predictions were validated with experimental data that corresponded to previous research by the same authors. A correct fit between the model predictions and the experimental data was observed because the modelling curves captured the major trends for the diesel distribution in each phase. The model parameters were compared to different previously reported values found in the literature. Pearson correlation coefficients were used to show the reproducibility level of the model. - Highlights: • A mathematical model is proposed to describe a soil bioremediation process. • The model couples mass transfer phenomena among phases with biodegradation. • Model predictions were validated with previous data reported by the authors. • A correct fit and correlation coefficients were observed.

  18. Surface water ponding on clayey soils managed by conventional and conservation tillage in boreal conditions

    Directory of Open Access Journals (Sweden)

    L. ALAKUKKU

    2008-12-01

    Full Text Available Surface water ponding and crop hampering due to soil wetness was monitored in order to evaluate the effects of conservation tillage practices and perennial grass cover on soil infiltrability for five years in situ in gently sloping clayey fields. Thirteen experimental areas, each having three experimental fields, were established in southern Finland. The fields belonged to: autumn mouldboard ploughing (AP, conservation tillage (CT and perennial grass in the crop rotation (PG. In the third year, direct drilled (DD fields were established in five areas. Excluding PG, mainly spring cereals were grown in the fields. Location and surface area of ponded water (in the spring and autumn as well as hampered crop growth (during June-July were determined in each field by using GPS devices and GIS programs. Surface water ponding or crop hampering occurred when the amount of rainfall was clearly greater than the long-term average. The mean of the relative area of the ponded surface water, indicating the risk of surface runoff, and hampered crop growth was larger in the CT fields than in the AP fields. The differences between means were, however, not statistically significant. Complementary soil physical measurements are required to investigate the reasons for the repeated surface water ponding.;

  19. A laboratory feasibility study on electrokinetic injection of nutrients on an organic, tropical, clayey soil.

    Science.gov (United States)

    Schmidt, Celina A B; Barbosa, Maria Claudia; de Almeida, Márcio de S S

    2007-05-17

    Based on the results of an environmental investigation program, carried out on an oil production field at Brazilian Northeast, a contamination diagnosis was made. The field was contaminated by crude oil and saline production water and the use of in situ electrokinetic bioremediation techniques in situ were suggested for the remediation of the contaminated site. The analyzed soil is a very humid clayey silt, with high plasticity, high electrical conductivity, low hydraulic conductivity, low density, large buffering capacity and high cation exchange capacity. The soil is rich in organic matter and poor in nitrogen. The removal of the contaminated soil for ex situ treatment is not advisable in contaminated studied area due to the restrictions imposed by local environmental authority, as well as operational impediments caused by the presence of vegetation and flooded conditions. After the diagnosis a program of laboratory tests was carried out on soil from the location in an electrical cell which was developed for this purpose. The study showed the feasibility of injecting nitrate and ammonium to this kind of soil, though the injection of phosphorous did not prove to be successful. It is recommended to control variations changes in pH, caused by the application of electrokinesis, in order not to harm the biodegradation process.

  20. Use of ash from the incineration of firewood and sawdust into clayey ceramic

    International Nuclear Information System (INIS)

    Rossi, D.P.; Monteiro, S.N.; Vieira, C.M.F.

    2011-01-01

    This work has as its objective to evaluate the effect of the incorporation of a type of waste, ash obtained from burning eucalyptus firewood and sawdust, in the physical and mechanical properties of red ceramic. The waste was characterized by DTA/TG and XRF. Formulations were prepared with incorporation of the waste in amounts up to 10 wt.%, into a kaolinitic clayey body. Rectangular specimens were prepared by uniaxial mold-press at 20 MPa and then fired at 650 and 950 deg C. The evaluated physical and mechanical properties were: linear shrinkage, water absorption and flexural rupture strength. The microstructure of the fired ceramics was evaluated by optical microscopy. The results showed that the ash has an high amount of weight loss during the firing, being predominantly composed of quartz and calcium compounds. The incorporation of the ash increased the water absorption and abruptly decreased the mechanical strength of the ceramic at the investigated temperatures for all amount of incorporated ash. (author)

  1. Distribution of petrophysical properties for sandy-clayey reservoirs by fractal interpolation

    Directory of Open Access Journals (Sweden)

    M. Lozada-Zumaeta

    2012-04-01

    Full Text Available The sandy-clayey hydrocarbon reservoirs of the Upper Paleocene and Lower Eocene located to the north of Veracruz State, Mexico, present highly complex geological and petrophysical characteristics. These reservoirs, which consist of sandstone and shale bodies within a depth interval ranging from 500 to 2000 m, were characterized statistically by means of fractal modeling and geostatistical tools. For 14 wells within an area of study of approximately 6 km2, various geophysical well logs were initially edited and further analyzed to establish a correlation between logs and core data. The fractal modeling based on the R/S (rescaled range methodology and the interpolation method by successive random additions were used to generate pseudo-well logs between observed wells. The application of geostatistical tools, sequential Gaussian simulation and exponential model variograms contributed to estimate the spatial distribution of petrophysical properties such as effective porosity (PHIE, permeability (K and shale volume (VSH. From the analysis and correlation of the information generated in the present study, it can be said, from a general point of view, that the results not only are correlated with already reported information but also provide significant characterization elements that would be hardly obtained by means of conventional techniques.

  2. Kinetic modelling of a diesel-polluted clayey soil bioremediation process

    International Nuclear Information System (INIS)

    Fernández, Engracia Lacasa; Merlo, Elena Moliterni; Mayor, Lourdes Rodríguez; Camacho, José Villaseñor

    2016-01-01

    A mathematical model is proposed to describe a diesel-polluted clayey soil bioremediation process. The reaction system under study was considered a completely mixed closed batch reactor, which initially contacted a soil matrix polluted with diesel hydrocarbons, an aqueous liquid-specific culture medium and a microbial inoculation. The model coupled the mass transfer phenomena and the distribution of hydrocarbons among four phases (solid, S; water, A; non-aqueous liquid, NAPL; and air, V) with Monod kinetics. In the first step, the model simulating abiotic conditions was used to estimate only the mass transfer coefficients. In the second step, the model including both mass transfer and biodegradation phenomena was used to estimate the biological kinetic and stoichiometric parameters. In both situations, the model predictions were validated with experimental data that corresponded to previous research by the same authors. A correct fit between the model predictions and the experimental data was observed because the modelling curves captured the major trends for the diesel distribution in each phase. The model parameters were compared to different previously reported values found in the literature. Pearson correlation coefficients were used to show the reproducibility level of the model. - Highlights: • A mathematical model is proposed to describe a soil bioremediation process. • The model couples mass transfer phenomena among phases with biodegradation. • Model predictions were validated with previous data reported by the authors. • A correct fit and correlation coefficients were observed.

  3. Geotechnical response of pipelines shallowly embedded in clayey and sandy soils

    Energy Technology Data Exchange (ETDEWEB)

    Oliveira, Jose Renato M.S. [Military Institute of Engineering (IME), Rio de Janeiro, RJ (Brazil); Borges, Ricardo G. [Centro de Pesquisa Leopoldo A. Miguez de Melo (CENPES/PETROBRAS), Rio de Janeiro, RJ (Brazil); Feitoza, Jaquelline; Almeida, Maria C.F.; Almeida, Marcio S.S. [Universidade Federal do Rio de Janeiro (COPPE/UFRJ), Rio de Janeiro, RJ (Brazil). Coordenacao dos Programas de Pos-graduacao de Engenharia

    2009-07-01

    Offshore and onshore pipelines used for oil and gas transportation are often buried to avoid eventual damages and also to provide movement constraint. The soil cover supply resistance against upward and lateral displacements of the pipe caused by thermally-induced axial loading, which can lead to structural buckling. The clear understanding of this behavior is critical for the development of new analysis tools and new design criteria which could minimize future accidents. In this way, research on pipe-soil interaction behavior has been undertaken using both clayey and sandy soils through physical and numerical simulations. This paper is part of a research effort to provide a pipe-soil interaction guideline suitable for application in pipeline design along the Brazilian coast. This work presents a comprehensive set of lateral buckling simulation tests using the COPPE-UFRJ geotechnical centrifuge. The chosen soils are typical of the Brazilian coast and therefore very representative of tropical regions. Physical and numerical results are compared and other research works are considered in order to assess the overall uplift resistance. In flight T-bar and cone penetration tests were undertaken to provide a soil resistance profile which was used to trace dimensionless curves that could be adopted in similar design situations. (author)

  4. Modelling Zn(II) sorption onto clayey sediments using a multi-site ion-exchange model

    International Nuclear Information System (INIS)

    Tertre, E.; Beaucaire, C.; Coreau, N.; Juery, A.

    2009-01-01

    In environmental studies, it is necessary to be able to predict the behaviour of contaminants in more or less complex physico-chemical contexts. The improvement of this prediction partly depends on establishing thermodynamic models that can describe the behaviour of these contaminants and, in particular, the sorption reactions on mineral surfaces. In this way, based on the mass action law, it is possible to use surface complexation models and ion exchange models. Therefore, the aim of this study is (i) to develop an ion-exchange model able to describe the sorption of transition metal onto pure clay minerals and (ii) to test the ability of this approach to predict the sorption of these elements onto natural materials containing clay minerals (i.e. soils/sediments) under various chemical conditions. This study is focused on the behaviour of Zn(II) in the presence of clayey sediments. Considering that clay minerals are cation exchangers containing multiple sorption sites, it is possible to interpret the sorption of Zn(II), as well as competitor cations, by ion-exchange equilibria with the clay minerals. This approach is applied with success to interpret the experimental data obtained previously in the Zn(II)-H + -Na + -montmorillonite system. The authors' research team has already studied the behaviour of Na + , K + , Ca 2+ and Mg 2+ versus pH in terms of ion exchange onto pure montmorillonite, leading to the development of a thermodynamic database including the exchange site concentrations associated with montmorillonite and the selectivity coefficients of Na + , K + , Ca 2+ , Mg 2+ , and Zn 2+ versus H + . In the present study, experimental isotherms of Zn(II) on two different sediments in batch reactors at different pH and ionic strengths, using NaCl and CaSO 4 as electrolytes are reported. Assuming clay minerals are the main ion-exchanging phases, it is possible to predict Zn(II) sorption onto sediments under different experimental conditions, using the previously

  5. Conceptual Design for Consolidation TCAP

    International Nuclear Information System (INIS)

    Klein, J.E.

    1999-01-01

    Two alternate Thermal Cycling Absorption Process (TCAP) designs have been developed for the Tritium Facility Modernization and Consolidation (TFM and C) Project. The alternate designs were developed to improve upon the existing Replacement Tritium Facility (RTF) TCAP design and to eliminate the use of building distributed hot and cold nitrogen system.A brief description of TCAP theory and modeling is presented, followed by an overview of the design criteria for the Isotope Separation System (ISS). Both designs are described in detail, along with a generic description of the complete TCAP system. A design is recommend for the Consolidation Project, and a development plan for both designs is proposed

  6. Theoretical Consolidation of Acoustic Dissipation

    Science.gov (United States)

    Casiano, M. J.; Zoladz, T. F.

    2012-01-01

    In many engineering problems, the effects of dissipation can be extremely important. Dissipation can be represented by several parameters depending on the context and the models that are used. Some examples of dissipation-related parameters are damping ratio, viscosity, resistance, absorption coefficients, pressure drop, or damping rate. This Technical Memorandum (TM) describes the theoretical consolidation of the classic absorption coefficients with several other dissipation parameters including linearized resistance. The primary goal of this TM is to theoretically consolidate the linearized resistance with the absorption coefficient. As a secondary goal, other dissipation relationships are presented.

  7. Dreaming and offline memory consolidation.

    Science.gov (United States)

    Wamsley, Erin J

    2014-03-01

    Converging evidence suggests that dreaming is influenced by the consolidation of memory during sleep. Following encoding, recently formed memory traces are gradually stabilized and reorganized into a more permanent form of long-term storage. Sleep provides an optimal neurophysiological state to facilitate this process, allowing memory networks to be repeatedly reactivated in the absence of new sensory input. The process of memory reactivation and consolidation in the sleeping brain appears to influence conscious experience during sleep, contributing to dream content recalled on awakening. This article outlines several lines of evidence in support of this hypothesis, and responds to some common objections.

  8. Preparation of an annual report for a consolidated radioisotope licence

    International Nuclear Information System (INIS)

    1985-01-01

    A consolidated radioisotope licence is a single license issued by the Atomic Energy Control Board (AECB) to an institution having many users of radioactive materials. The licence is issued when the institution has fulfilled the requirements set by the AECB and has implemented policies and procedures which will ensure the maintenance of an effective radiation safety program. The consolidated licence is retained only if the results of AECB inspections are satisfactory -- or remedial action is taken promptly -- and if the institution reports regularly about the status of its radiation safety program. One aspect of this reporting procedure is an annual report. This guide describes the information that the AECB requires in the annual report. The guide applies primarily to universities and research institutions where a wide variety of radioisotope uses take place. The guide does not affect most other institutions or facilities, either because the nature and extent of their operations with radioactive materials do not lend themselves to consolidated licensing or because they are not licensed by the Radioisotopes and Transportation Division. (For example, this guide does not apply to reactors, to accelerators, or to waste management or uranium mining or refining facilities.) The information in the annual report should be specific to the consolidated radioisotope licence. Incidents, staff exposures, and waste associated with accelerators, research reactors, and waste management facilities should be excluded from this report unless they affected activities under the consolidated licence

  9. Hydrostatic and shear consolidation tests with permeability measurements on Waste Isolation Pilot Plant crushed salt

    International Nuclear Information System (INIS)

    Brodsky, N.S.

    1994-03-01

    Crushed natural rock salt is a primary candidate for use as backfill and barrier material at the Waste Isolation Pilot Plant (WIPP) and therefore Sandia National Laboratories (SNL) has been pursuing a laboratory program designed to quantify its consolidation properties and permeability. Variables that influence consolidation rate that have been examined include stress state and moisture content. The experimental results presented in this report complement existing studies and work in progress conducted by SNL. The experiments described in this report were designed to (1) measure permeabilities of consolidated specimens of crushed salt, (2) determine the influence of brine saturation on consolidation under hydrostatic loads, and 3) measure the effects of small applied shear stresses on consolidation properties. The laboratory effort consisted of 18 individual tests: three permeability tests conducted on specimens that had been consolidated at Sandia, six hydrostatic consolidation and permeability tests conducted on specimens of brine-saturated crushed WIPP salt, and nine shear consolidation and permeability tests performed on crushed WIPP salt specimens containing 3 percent brine by weight. For hydrostatic consolidation tests, pressures ranged from 1.72 MPa to 6.90 MPa. For the shear consolidation tests, confining pressures were between 3.45 MPa and 6.90 MPa and applied axial stress differences were between 0.69 and 4.14 MPa. All tests were run under drained conditions at 25 degrees C

  10. Preliminary analysis in a clayey mass aimed at ceramic blocks production: physical and mineralogical characteristics; Analise preliminar em uma massa argilosa visando a producao de blocos ceramicos: caracteristicas fisicas e mineralogicas

    Energy Technology Data Exchange (ETDEWEB)

    Silva, L.J.M.D. da; Apolonio, T.G.; Salviano, A.F.; Taveira, S.K.A.; Garcia, T.G.C.; Silva, J; Luna, P.A.; Macedo, R.S., E-mail: reginaldo.severo@ufcg.edu.br [Universidade Federal de Campina Grande (UFCG), PB (Brazil)

    2016-07-01

    The physical, chemical and mineralogical characterization of the clayey mass are important in determining its properties, allowing a better knowledge of the raw material used in the manufacture of ceramic products. This work aims to characterize the raw material used in the manufacture of ceramic sealing blocks in a ceramic industry. Thus, it was evaluated by laboratory tests the raw material used in the production of ceramic blocks in a ceramics industry in the region of Carnauba dos Dantas, RN. The methodology used in the tests is the same as the IPT, which consists in carrying out the plasticity testing, particle size, chemical analysis and X-ray diffraction. Results indicate that the sample studied by the physical and mineralogical characteristics, has the potential to be applied in the manufacture of red ceramic products for use in construction. (author)

  11. Review on the explosive consolidation methods to fabricate tungsten based PFMs

    Energy Technology Data Exchange (ETDEWEB)

    Wang, Shuming, E-mail: wangshuming@ustb.edu.cn; Sun, Chongxiao; Guo, Wenhao; Yan, Qingzhi; Zhou, Zhangjian; Zhang, Yingchun; Shen, Weiping; Ge, Changchun

    2014-12-15

    Tungsten is one of the best candidates for plasma-facing materials in the fusion reactors, owing to its many unique properties. In the development of tungsten-based Plasma Facing Materials/Components (PFMs/PFCs), materials scientists have explored many different, innovative preparation and processing routes to meet the requirement of International Thermonuclear Experimental Reactor (ITER). Some explosive consolidation technology intrinsic characteristics, which make it suitable for powder metallurgy (powders consolidation) and PFMs production, are the high pressure processing, highly short heating time and can be considered as a highly competitive green technology. In this work, an overview of explosive consolidation techniques applied to fabricate tungsten-based PFMs is presented. Emphasis is given to describe the main characteristics and potentialities of the explosive sintering, explosive consolidation techniques. The aspects presented and discussed in this paper indicate the explosive consolidation processes as a promising and competitive technology for tungsten-based PFMs processing.

  12. Synaptic consolidation across multiple timescales

    Directory of Open Access Journals (Sweden)

    Lorric Ziegler

    2014-03-01

    Full Text Available The brain is bombarded with a continuous stream of sensory events, but retains only a small subset in memory. The selectivity of memory formation prevents our memory from being overloaded with irrelevant items that would rapidly bring the brain to its storage limit; moreover, selectivity also prevents overwriting previously formed memories with new ones. Memory formation in the hippocampus, as well as in other brain regions, is thought to be linked to changes in the synaptic connections between neurons. In this view, sensory events imprint traces at the level of synapses that reflect potential memory items. The question of memory selectivity can therefore be reformulated as follows: what are the reasons and conditions that some synaptic traces fade away whereas others are consolidated and persist? Experimentally, changes in synaptic strength induced by 'Hebbian' protocols fade away over a few hours (early long-term potentiation or e-LTP, unless these changes are consolidated. The experiments and conceptual theory of synaptic tagging and capture (STC provide a mechanistic explanation for the processes involved in consolidation. This theory suggests that the initial trace of synaptic plasticity sets a tag at the synapse, which then serves as a marker for potential consolidation of the changes in synaptic efficacy. The actual consolidation processes, transforming e-LTP into late LTP (l-LTP, require the capture of plasticity-related proteins (PRP. We translate the above conceptual model into a compact computational model that accounts for a wealth of in vitro data including experiments on cross-tagging, tag-resetting and depotentiation. A central ingredient is that synaptic traces are described with several variables that evolve on different time scales. Consolidation requires the transmission of information from a 'fast' synaptic trace to a 'slow' one through a 'write' process, including the formation of tags and the production of PRP for the

  13. Mechanical behaviour and rupture in clayey rocks studied by x-ray micro tomography; Comportement mecanique et rupture dans les roches argileuses etudies par micro tomographie a rayons X

    Energy Technology Data Exchange (ETDEWEB)

    Lenoir, N

    2006-03-15

    Within the framework of feasibility studies of underground repositories for radioactive waste, the study of permeability evolution with damage of the host layer is crucial. The goals of this work were: (i) to characterize experimentally the damage of two clayey rocks (BEAUCAIRE MARL and EAST SHALE) with x-ray micro tomography, (ii) to develop a high pressure triaxial set-up adapted to permeability measurement on very low permeability rocks.A number of original triaxial devices have been realised to characterize damage of clayey rocks, under deviatoric loading, with x-ray micro tomography on a synchrotron beamline at the ESRF (Grenoble). Localized damage and its evolution have been characterized at a fine scale (of order of ten microns). Digital image correlation techniques, extended to 3d images, have been used to measure incremental strain fields from tomographic images. we demonstrated that these techniques are very useful in the study of the localized damage of geo-materials and especially for the initiation. A high pressure triaxial device has been realised to measure permeability evolution of the east shale as a function of applied stress (isotropic and deviatoric). The particularity of this set-up is the small size of the test specimen (cylinder of 10 mm in diameter and 20 mm in height) which allows significant reduction of test duration. (author)

  14. 49 CFR 172.404 - Labels for mixed and consolidated packaging.

    Science.gov (United States)

    2010-10-01

    ... 49 Transportation 2 2010-10-01 2010-10-01 false Labels for mixed and consolidated packaging. 172..., TRAINING REQUIREMENTS, AND SECURITY PLANS Labeling § 172.404 Labels for mixed and consolidated packaging. (a) Mixed packaging. When hazardous materials having different hazard classes are packed within the...

  15. Fully coupled modeling of radionuclide migration in a clayey rock disturbed by alkaline plume

    International Nuclear Information System (INIS)

    Pellegrni, D.; Windt, L. de; Lee, J.V.D.

    2002-03-01

    The disposal of radioactive wastes in clayey formations may require the use of large amounts of concrete and cement as a barrier to minimize corrosion of steel containers and radionuclide migration and for supporting drifts and disposal vaults. In this context, reactive transport modeling of the interactions between cement or concrete and the argillaceous host rock aims at estimating the evolution in time of the containment properties of the multi-barriers system. The objectives of the paper are to demonstrate that integrating radionuclides migration in the modeling of strongly coupled geochemical processes of cement-clay stone interactions is feasible and that it represents an efficient way to assess the sensitivity and modification of the classical Kd and solubility parameters with respect to the chemical evolutions. Two types of modeling are considered in the paper: i): calculation of intrinsic solubility limits and Kd values backing up on the results of modeling of cement/clay stone interactions (radionuclides are assumed to be present over the whole domain at any time whatever the scenario), ii) full mechanistic modeling which explicitly introduces radionuclides in the calculation with ad hoc assumptions on radionuclide inventory, canister failure, migration pathway, etc. The reactive transport code HYTEC, based on the geochemical code CHESS, is used to simulate both the cement-clay stone interaction processes and the radionuclide migration in 1-D and 2-D configurations. Convective/dispersive and diffuse transport can be simulated for solutes and colloids. A wide range of processes such as aqueous chemistry, redox, dissolution/precipitation, surface complexation and ion exchange can be modeled at equilibrium or with kinetic control. In addition, HYTEC is strongly coupled, i.e. the hydrology (flow and diffusion) may change when mineral precipitation or dissolution changes the local porosity. (authors)

  16. Consolidated results 2000. Forecasts 2001; Resultats consolides 2000. Perspectives 2001

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    2001-07-01

    This document presents an economic analysis of the Group Gaz De France consolidated results for the year 2000. The main topics are the evolution of the energy market, the great economic growth for the five businesses of the Group (exploration-production, trade, transport, distribution and services), financial results affected by the supply costs increase, the position reinforcement among the gas leaders in Europe and the highlights of 2000. (A.L.B.)

  17. Common consolidated corporate tax base: grouping and consolidation

    Directory of Open Access Journals (Sweden)

    Danuše Nerudová

    2012-01-01

    Full Text Available After the ten years of work and discussion of the proposal the European Commission has published the proposal of CCCTB directive on 16th March, 2011. This proposal can be considered as unique, for the European Commission is suggesting totally new system of corporate taxation. The aim of the paper is to research the rules for consolidation and grouping suggested in the proposal of CCCTB directive, to identify the possible conflict situations and to suggest the possible solution. The focuses on the provisions regarding the conditions for consolidation and grouping, comprised in chapter IX, Art. 54–60. In that area has been identified, that even though the provisions seem to be clear, their practical application can in some situations lead to double interpretation, mainly with respect to the fact that individual member states are responsible for the implementation of the directive and also national tax administrators and national courts are going to interpret the provisions of the directive. Therefore even though the fact that suggested system is unique and addresses a lot of problems which are facing companies running business on the internal market, the provisions regarding the consolidation rules and rules for group formatting may still lead not to unified interpretation. In that respect, some of the rules should be more specific in order to ensure unified interpretation.

  18. Sandia solidification process: consolidation and characterization. Part I. Consolidation studies

    International Nuclear Information System (INIS)

    Johnstone, J.K.

    1978-05-01

    The consolidation behavior of a complex polycrystalline ceramic nuclear waste form composed of titanates, zeolite, and metallic silicon was studied. Initial solidification takes place by an ion exchange process. The resulting powder exhibits a large surface area, approximately 350 m 2 /g, and several decomposition, crystallization and phase change reactions from room temperature to 1100 0 C. In spite of the large surface area, consolidation by cold pressing and atmospheric sintering to 1100 0 C was not satisfactory. Vacuum hot pressing was found to produce fully dense pellets (less than 1% residual porosity) under very mild conditions, 6.9 MPa (1100 psi) and 1100 0 C. The dominant densification mechanism was viscous flow. Under less than optimum hot pressing conditions, three stages of densification were observed. Initial densification took place by particle rearrangement which was described with a viscous flow model. Second stage densification occurred by a solution-precipitation process controlled by a phase boundary dissolution reaction. In several cases, a third, final densification stage was observed. Detailed studies describe the effects of heating rate, processing temperature, pressure, residence time, atmosphere, composition, heat treatment, and the addition of consolidation aids on the densification behavior. In addition, fully radioactive high level mixed fission product titanate/waste pellets (1.27 cm diameter) were hot pressed at Oak Ridge National Laboratory to demonstrate the feasibility of such a process in a remotely operated hot cell. High density uniform pellets were obtained

  19. 77 FR 45721 - Consolidated Audit Trail

    Science.gov (United States)

    2012-08-01

    ... maintain a consolidated order tracking system, or consolidated audit trail, with respect to the trading of... With a Consolidated Audit Trail 3. Large Trader Reporting System Rule B. Summary of Proposed Rule 613 C... Authority (``FINRA'') and some of the exchanges currently maintain their own separate audit trail systems...

  20. A thermomechanical crystal plasticity constitutive model for ultrasonic consolidation

    KAUST Repository

    Siddiq, Amir

    2012-01-01

    We present a micromechanics-based thermomechanical constitutive model to simulate the ultrasonic consolidation process. Model parameters are calibrated using an inverse modeling approach. A comparison of the simulated response and experimental results for uniaxial tests validate and verify the appropriateness of the proposed model. Moreover, simulation results of polycrystalline aluminum using the identified crystal plasticity based material parameters are compared qualitatively with the electron back scattering diffraction (EBSD) results reported in the literature. The validated constitutive model is then used to simulate the ultrasonic consolidation process at sub-micron scale where an effort is exerted to quantify the underlying micromechanisms involved during the ultrasonic consolidation process. © 2011 Elsevier B.V. All rights reserved.

  1. Efforts to Consolidate Chalcogels with Adsorbed Iodine

    Energy Technology Data Exchange (ETDEWEB)

    Riley, Brian J.; Pierce, David A.; Chun, Jaehun

    2013-08-28

    This document discusses ongoing work with non-oxide aerogels, called chalcogels, that are under development at the Pacific Northwest National Laboratory as sorbents for gaseous iodine. Work was conducted in fiscal year 2012 to demonstrate the feasibility of converting Sn2S3 chalcogel without iodine into a glass. This current document summarizes the work conducted in fiscal year 2013 to assess the consolidation potential of non-oxide aerogels with adsorbed iodine. The Sn2S3 and Sb13.5Sn5S20 chalcogels were selected for study. The first step in the process for these experiments was to load them with iodine (I2). The I2 uptake was ~68 mass% for Sn2S3 and ~50 mass% for Sb13.5Sn5S20 chalcogels. X-ray diffraction (XRD) of both sets of sorbents showed that metal-iodide complexes were formed during adsorption, i.e., SnI4 for Sn2S3 and SbI3 for Sb13.5Sn5S20. Additionally, metal-sulfide-iodide complexes were formed, i.e., SnSI for Sn2S3 and SbSI for Sb13.5Sn5S20. No XRD evidence for unreacted iodine was found in any of these samples. Once the chalcogels had reached maximum adsorption, the consolidation potential was assessed. Here, the sorbents were heated for consolidation in vacuum-sealed quartz vessels. The Sb13.5Sn5S20 chalcogel was heated both (1) in a glassy carbon crucible within a fused quartz tube and (2) in a single-containment fused quartz tube. The Sn2S3 chalcogel was only heated in a single-containment fused quartz tube. In both cases with the single-containment fused quartz experiments, the material consolidated nicely. However, in both cases, there were small fractions of metal iodides not incorporated into the final product as well as fused quartz particles within the melt due to the sample attacking the quartz wall during the heat treatment. The Sb13.5Sn5S20 did not appear to attack the glassy carbon crucible so, for future experiments, it would be ideal to apply a coating, such as pyrolytic graphite, to the inner walls of the fused quartz vessel to prevent

  2. Consolidated PCBs [polychlorinated biphenyls] improves waste control

    International Nuclear Information System (INIS)

    Smith, E.

    1991-01-01

    Consolidation of polychlorinated biphenyl (PCB) wastes is recommended for improving ownership control of wastes, eliminating PCB storage sites, and increasing cost-effectiveness of waste management. In Ontario, sites receiving the waste must be owned by the waste generator and registered as a PCB site. All PCBs must be removed from a site with no contaminated materials or wastes left behind, which requires a thorough site assessment to identify wastes prior to removal, a sampling and analytical scheme if necessary, and an approved plan for site cleanup. If large volumes of PCB-contaminated oil are involved, it may be cost-effective to put oil from several sites into bulk tanks and thus avoid the need to handle and decontaminate a large number of drums. With low volumes of oil, it may be possible to move the waste to another site where mobile PCB destruction is taking place. It also may be possible to get approval to blend high-level PCB liquids with mineral oil to reduce the PCB concentration to a level where chemical decontamination is allowed. For large volumes of high-level PCB wastes, consolidation will be necessary simply because of the high costs of mobilizing an incinerator and the requirement for public hearings for each incineration project. To make such a project cost-effective, PCB wastes will have to be concentrated from a large geographic area. 1 fig

  3. Method for consolidating incompetent formations

    Energy Technology Data Exchange (ETDEWEB)

    Pavlich, J.P.; Calvert, D.G.

    1965-02-23

    An incompetent formation is consolidated and left permeable by first injecting a solidifiable liquid resin, and following this by an organic liquid to set the resin. The liquid resin used may be 3 (glycidyloxy) propyl trimethoxysilane in sufficient concentration to considerably increase the compressive strength of the consolidated zone. The silane may be used in a ratio of between 0.5 and 5% of the total volume of the liquid resin. The liquid resin used may be a phenol-formaldehyde condensation product dispersed in an aliphatic alcohol with from 1 to 4 carbon atoms. The liquid resin used may be an epoxy containing a hardener. The resin may be displaced into the formation by a liquid hydrocarbon. (5 claims)

  4. To Replay, Perchance to Consolidate.

    Directory of Open Access Journals (Sweden)

    Lisa Genzel

    2015-10-01

    Full Text Available After a memory is formed, it continues to be processed by the brain. These "off-line" processes consolidate the memory, leading to its enhancement and to changes in memory circuits. Potentially, these memory changes are driven by off-line replay of the pattern of neuronal activity present when the memory was being formed. A new study by Dhaksin Ramanathan and colleagues, published in PLOS Biology, demonstrates that replay occurs predominately after the acquisition of a new motor skill and that it is related to changes in memory performance and to the subsequent changes in memory circuits. Together, these observations reveal the importance of neuronal replay in the consolidation of novel motor skills.

  5. Consolidation of nanometer-sized aluminum single crystals: Microstructure and defects evolutions

    KAUST Repository

    Afify, N. D.

    2014-04-01

    Deriving bulk materials with ultra-high mechanical strength from nanometer-sized single metalic crystals depends on the consolidation procedure. We present an accurate molecular dynamics study to quantify microstructure responses to consolidation. Aluminum single crystals with an average size up to 10.7 nm were hydrostatically compressed at temperatures up to 900 K and pressures up to 5 GPa. The consolidated material developed an average grain size that grew exponentially with the consolidation temperature, with a growth rate dependent on the starting average grain size and the consolidation pressure. The evolution of the microstructure was accompanied by a significant reduction in the concentration of defects. The ratio of vacancies to dislocation cores decreased with the average grain size and then increased after reaching a critical average grain size. The deformation mechanisms of poly-crystalline metals can be better understood in the light of the current findings. © 2013 Elsevier B.V. All rights reserved.

  6. Consolidation of nanometer-sized aluminum single crystals: Microstructure and defects evolutions

    KAUST Repository

    Afify, N. D.; Salem, H. G.; Yavari, A.; El Sayed, Tamer S.

    2014-01-01

    Deriving bulk materials with ultra-high mechanical strength from nanometer-sized single metalic crystals depends on the consolidation procedure. We present an accurate molecular dynamics study to quantify microstructure responses to consolidation. Aluminum single crystals with an average size up to 10.7 nm were hydrostatically compressed at temperatures up to 900 K and pressures up to 5 GPa. The consolidated material developed an average grain size that grew exponentially with the consolidation temperature, with a growth rate dependent on the starting average grain size and the consolidation pressure. The evolution of the microstructure was accompanied by a significant reduction in the concentration of defects. The ratio of vacancies to dislocation cores decreased with the average grain size and then increased after reaching a critical average grain size. The deformation mechanisms of poly-crystalline metals can be better understood in the light of the current findings. © 2013 Elsevier B.V. All rights reserved.

  7. Consolidated results 2000. Forecasts 2001

    International Nuclear Information System (INIS)

    2001-01-01

    This document presents an economic analysis of the Group Gaz De France consolidated results for the year 2000. The main topics are the evolution of the energy market, the great economic growth for the five businesses of the Group (exploration-production, trade, transport, distribution and services), financial results affected by the supply costs increase, the position reinforcement among the gas leaders in Europe and the highlights of 2000. (A.L.B.)

  8. Pilot-scale bioremediation of a petroleum hydrocarbon-contaminated clayey soil from a sub-Arctic site

    Energy Technology Data Exchange (ETDEWEB)

    Akbari, Ali; Ghoshal, Subhasis, E-mail: subhasis.ghoshal@mcgill.ca

    2014-09-15

    Highlights: • Aeration and moisture addition alone caused extensive hydrocarbon biodegradation. • 30-day slurry reactor remediation endpoints attained in 385 days in biopiles. • High nitrogen concentrations inhibited hydrocarbon degradation. • Inhibition of biodegradation linked to lack of shifts in soil microbial community. - Abstract: Bioremediation is a potentially cost-effective solution for petroleum contamination in cold region sites. This study investigates the extent of biodegradation of petroleum hydrocarbons (C16–C34) in a pilot-scale biopile experiment conducted at 15 °C for periods up to 385 days, with a clayey soil, from a crude oil-impacted site in northern Canada. Although several studies on bioremediation of petroleum hydrocarbon-contaminated soils from cold region sites have been reported for coarse-textured, sandy soils, there are limited studies of bioremediation of petroleum contamination in fine-textured, clayey soils. Our results indicate that aeration and moisture addition was sufficient for achieving 47% biodegradation and an endpoint of 530 mg/kg for non-volatile (C16–C34) petroleum hydrocarbons. Nutrient amendment with 95 mg-N/kg showed no significant effect on biodegradation compared to a control system without nutrient but similar moisture content. In contrast, in a biopile amended with 1340 mg-N/kg, no statistically significant biodegradation of non-volatile fraction was detected. Terminal Restriction Fragment Length Polymorphism (T-RFLP) analyses of alkB and 16S rRNA genes revealed that inhibition of hydrocarbon biodegradation was associated with a lack of change in microbial community composition. Overall, our data suggests that biopiles are feasible for attaining the bioremediation endpoint in clayey soils. Despite the significantly lower biodegradation rate of 0.009 day{sup −1} in biopile tank compared to 0.11 day{sup −1} in slurry bioreactors for C16–C34 hydrocarbons, the biodegradation extents for this fraction

  9. Pilot-scale bioremediation of a petroleum hydrocarbon-contaminated clayey soil from a sub-Arctic site

    International Nuclear Information System (INIS)

    Akbari, Ali; Ghoshal, Subhasis

    2014-01-01

    Highlights: • Aeration and moisture addition alone caused extensive hydrocarbon biodegradation. • 30-day slurry reactor remediation endpoints attained in 385 days in biopiles. • High nitrogen concentrations inhibited hydrocarbon degradation. • Inhibition of biodegradation linked to lack of shifts in soil microbial community. - Abstract: Bioremediation is a potentially cost-effective solution for petroleum contamination in cold region sites. This study investigates the extent of biodegradation of petroleum hydrocarbons (C16–C34) in a pilot-scale biopile experiment conducted at 15 °C for periods up to 385 days, with a clayey soil, from a crude oil-impacted site in northern Canada. Although several studies on bioremediation of petroleum hydrocarbon-contaminated soils from cold region sites have been reported for coarse-textured, sandy soils, there are limited studies of bioremediation of petroleum contamination in fine-textured, clayey soils. Our results indicate that aeration and moisture addition was sufficient for achieving 47% biodegradation and an endpoint of 530 mg/kg for non-volatile (C16–C34) petroleum hydrocarbons. Nutrient amendment with 95 mg-N/kg showed no significant effect on biodegradation compared to a control system without nutrient but similar moisture content. In contrast, in a biopile amended with 1340 mg-N/kg, no statistically significant biodegradation of non-volatile fraction was detected. Terminal Restriction Fragment Length Polymorphism (T-RFLP) analyses of alkB and 16S rRNA genes revealed that inhibition of hydrocarbon biodegradation was associated with a lack of change in microbial community composition. Overall, our data suggests that biopiles are feasible for attaining the bioremediation endpoint in clayey soils. Despite the significantly lower biodegradation rate of 0.009 day −1 in biopile tank compared to 0.11 day −1 in slurry bioreactors for C16–C34 hydrocarbons, the biodegradation extents for this fraction were

  10. Pilot-scale bioremediation of a petroleum hydrocarbon-contaminated clayey soil from a sub-Arctic site.

    Science.gov (United States)

    Akbari, Ali; Ghoshal, Subhasis

    2014-09-15

    Bioremediation is a potentially cost-effective solution for petroleum contamination in cold region sites. This study investigates the extent of biodegradation of petroleum hydrocarbons (C16-C34) in a pilot-scale biopile experiment conducted at 15°C for periods up to 385 days, with a clayey soil, from a crude oil-impacted site in northern Canada. Although several studies on bioremediation of petroleum hydrocarbon-contaminated soils from cold region sites have been reported for coarse-textured, sandy soils, there are limited studies of bioremediation of petroleum contamination in fine-textured, clayey soils. Our results indicate that aeration and moisture addition was sufficient for achieving 47% biodegradation and an endpoint of 530 mg/kg for non-volatile (C16-C34) petroleum hydrocarbons. Nutrient amendment with 95 mg-N/kg showed no significant effect on biodegradation compared to a control system without nutrient but similar moisture content. In contrast, in a biopile amended with 1340 mg-N/kg, no statistically significant biodegradation of non-volatile fraction was detected. Terminal Restriction Fragment Length Polymorphism (T-RFLP) analyses of alkB and 16S rRNA genes revealed that inhibition of hydrocarbon biodegradation was associated with a lack of change in microbial community composition. Overall, our data suggests that biopiles are feasible for attaining the bioremediation endpoint in clayey soils. Despite the significantly lower biodegradation rate of 0.009 day(-1) in biopile tank compared to 0.11 day(-1) in slurry bioreactors for C16-C34 hydrocarbons, the biodegradation extents for this fraction were comparable in these two systems. Copyright © 2014 Elsevier B.V. All rights reserved.

  11. High-frequency HYDRO-geophysical observations for an advanced understanding of clayey landSLIDES: the HYDROSLIDE research project

    Science.gov (United States)

    Malet, Jean-Philippe; Supper, Robert; Flores-Orozco, Adrian; Gautier, Stéphanie; Bogaard, Thom

    2017-04-01

    As a consequence of change in hydrological cycles and the increase of exposed goods, the risk of landslides is globally growing all over the world. As a consequence, short-time landslide prediction is a fundamental tool for risk mitigation. To this aim, real-time monitoring and interpretation methods aiming at a full exploitation of the available landslide information are needed, including further development of sensor technology and use of advanced numerical modeling. The most commonly used warning parameters are direct measurements of slope displacement and pore-water pressures. However, recent research on landslide controlled by slope hydrology has shown that other parameters (e.g. soil moisture) can be used and other methods (e.g. electrical resistivity tomography, electrical spontaneous potential) are available, which might give indications on triggering even before an actual displacement is measureable and thus could possibly be used as physical precursors for short-term warning. The CNRS - Ecole et Observatoire des Sciences de la Terre (EOST) and the Geological Survey of Austria - Geophysical Division (GBA) started successfully to evaluate time-lapse resistivity measurements for monitoring changes in water content/flows in landslides at different monitoring sites. At the same period, CNRS also started to establish the French Observatory on Landslides (OMIV: omiv.unistra.fr), which task is the long term monitoring and data sharing of landslide parameters (geodesy, hydrology, seismic). Results from these projects proved that electrical resistivity monitoring can be successfully applied to detect changes in water storage and to understand water circulation in complex landslide bodies. However, especially for clayey landslides, this method is only applicable with limitation, since the resistivity of clays shows almost the same values as the resistivity of the saturated soil (15-20 O.m). Consequently, the change in water content expressed in the electrical

  12. Clays as tracers of diagenetic and hydrothermal paleo-conditions. Search for mineralogical and geochemical evidences of hydrothermal circulations in clayey, sandstone-like and carbonated diagenetic Triassic formations of the Paris Basin

    International Nuclear Information System (INIS)

    Ploquin, Florian

    2011-01-01

    Within the framework of the multi-organization TAPSS 2000 program - GNR-FORPRO, led on the Bure site (Meuse-France), the ANDRA Company realized a deep drilling (named EST 433) to investigate the local Trias because the grounds Triassic levels constituting the bed rock of Clayey level for the storage of the nuclear waste. The drilling cut the Trias rocks on a total thickness of 700 m, successively from the bottom up: (1) the Buntsandstein (120 m) is characterized by sandy-conglomerate facies; (2) the Muschelkalk (150 m) is essentially consisted of clayey-sandy-siltstone series headed by a dolomitic deposit system; (3) the Keuper part (450 m) is an alternation of sandy clay-stone or silty clay-stone deposits with insertions of saliferous levels; (4) finally the Rethian part of the drilling associated with Hettangian (80 m), are characterized by clayey-shale facies. This litho-stratigraphy can redraw the evolution of the sedimentary paleo-environments since fluviatile circles (Buntsandstein) then lagoon (upper Muschelkalk), to large floods plains systems occasionally invaded by sea (Keuper) and, finally, in an epi-continental sea context (Rhetian-Hettangian) announcing the generalized transgressive phase of which the progressive evolution coming from the border towards the center of the basin. The nearness of the continental areas is recorded in the detrital fraction of the Triassic sediments. The geochemistry of these materials signs their continental crust character and their associated isotopic Nd-Sm values gives a Hercynian meta-sediments and granites origin with from time to time a contribution of young forming rock. The mineralogy of the clayey fraction (< 0,2μm) shows that only the conglomerate on the base of the drilling consists of an assembly of dickite and illites strictly associated with regular illite / smectite mixed-layer of R=1 type illite-rich. These last ones are the main part of the clayey mineralogy of the draining facies of Buntsandstein and are

  13. FEATURES OF CONSOLIDATED FINANCIAL STATEMENTS: FOREIGN EXPERIENCE

    Directory of Open Access Journals (Sweden)

    S. V. KUCHER

    2016-12-01

    Full Text Available The article researches the features of preparation and submission of the consolidated financial statements of the world countries of different systems of accounting standardization in order to identify the areas of accounting improvement for the process of consolidation of financial reporting indicators. The main problems of consolidated financial statements preparation by business entities in Ukraine are determined. The author determines the theoretical and practical problems of consolidation of financial statements of organizational and methodical character. The comparative analysis of the features of standardization process of financial statements consolidation in the world countries is carried out. The main differences in the requirements for the formation of consolidated financial statements indicators of such countries as the French Republic, the Federal Republic of Germany, the Republic of Belarus and the People’s Republic of China are outlined. The main directions of scientific researches on the improvement of accounting and analytical support for the preparation of consolidated financial statements are formed.

  14. Expansion reduction of clayey soils through Surcharge application and Lime Treatment

    Directory of Open Access Journals (Sweden)

    T. López-Lara

    2017-12-01

    Full Text Available Expansive clayey soils produce heaving and cracking of floor slabs and walls. Expansive soils owe their characteristics to the presence of swelling clay minerals. This soil expands and contracts due to changes in the moisture content of the soil. In this study the surcharge required to counteract soil expansion was measured in natural expansive soils (untreated soils and lime treated soils starting at 19.61 kPa (2 Ton/m2 and continuing with increments of 19.61 kPa. Additionaly in lime treated soils the amount of lime was determined under different surcharges in order to reduce the expansion. The test results indicated that the surcharges applied to untreated soils were not proportional to the decrease of expansion which is probably due to the increase of soil density. In fact, only the initial surcharge of 19.61 kPa significantly decreased the expansion. According to the results, the soil expansion was considerably reduced (1.54% with the surcharge of 78.45 kPa, therefore this surcharge can be considered as the Swelling pressure. On the other hand the soil tested (high compressibility clay was stabilized with 6% of lime (without surcharges which was determined with the lowest value of liquid limit and plastic index as well as expansion test. After the application of surcharges and lime treatment to expansive soil, the surcharges of 39.22 kPa and 58.84 kPa decreased expansion and increased their resistance. This was concluded by similar low values of expansion (without settlements under both surcharges of each treated soil tested (2, 4 and 6% of lime. It can be concluded that the surcharge contributed to the decrease of soil expansion due to the decrease of the amount of lime required (6% without surcharge. So, 4% of lime was enough for the surcharge of 19.61 kPa and 2% of lime required the surcharge minimum of 39.22 kPa. This shows that the surcharge of a house on expansive soil reduces soil expansion and therefore reduces costs of any

  15. Biostimulation and rainfall infiltration: influence on retention of biodiesel in residual clayey soil.

    Science.gov (United States)

    Thomé, Antônio; Cecchin, Iziquiel; Reginatto, Cleomar; Colla, Luciane M; Reddy, Krishna R

    2017-04-01

    This study investigates the retention of biodiesel in residual clayey soil during biostimulation by nutrients (nitrogen, phosphorus, and potassium) under conditions of rainfall infiltration. Several column tests were conducted in a laboratory under different void ratios (1.14, 1.24, and 1.34), varying moisture contents (15, 25, and 35%), and in both the presence and absence of biostimulation. The volume of biodiesel (which was equivalent to the volume of voids in the soil) was placed atop the soil and allowed to percolate for a period of 15 days. The soil was subjected to different rainfall infiltration conditions (0.30 or 60 mm). The greatest reductions in residual contaminants occurred after 60 mm of rain simulation, at values of up to 74% less than in samples with the same conditions but no precipitation. However, the residual contamination decay rate was greater with 0-30 mm (0.29 g/mm) of precipitation than with 30-60 mm (0.075 g/mm). Statistical assessment revealed that increased moisture and the presence of nutrients were the factors with the most powerful effect on contaminant retention in the soil. The residual contaminant level was 21 g/kg at a moisture content of 15% and no precipitation, decreasing to 12 g/kg at 35% moisture and no precipitation. Accordingly, it is possible to conclude that biostimulation and rainfall infiltration conditions can decrease the retention of contaminants in soil and allow a greater leaching or spreading of the contamination. All of these phenomena are worthy of careful examination for the in situ bioremediation of organic contamination. • The higher moisture in the soil, due to a high initial moisture content and/or infiltration of rainfall, can reduce contaminant retention, • The use of biostimulation through the addition of nutrients to accelerate the biodegradation of toxic organic contaminants may induce inadvertent undesirable interactions between the soil and the contaminant. • When adopting

  16. Report E : self-consolidating concrete (SCC) for infrastructure elements - hardened mechanical properties and durability performance.

    Science.gov (United States)

    2012-08-01

    Concrete is one of the most produced and utilized materials in the world. Due to : the labor intensive and time consuming nature of concrete construction, new and : innovative concrete mixes are being explored. Self-consolidating concrete (SCC) is on...

  17. The Influence of SAND’s Gradation and Clay Content of Direct Sheart Test on Clayey Sand

    Science.gov (United States)

    Wibisono, Gunawan; Agus Nugroho, Soewignjo; Umam, Khairul

    2018-03-01

    The shear strength of clayey-sand can be affected by several factors, e.g. gradation, density, moisture content, and the percentage of clay and sand fraction. The same percentage of clay and sand fraction in clayey-sand mixtures may have different shear strengths due to those factors. This research aims to study the effect of clay content on sand that cause the change of its shear strength. Samples consisted of different clay and sand fractions were reconstituted at a certain moisture content. Sand fractions varied from well-graded to poorly-graded sand. Shear strength was measured in terms of the direct shear test. Prior to the test, surcharge loads were applied to represent overburden pressures. Shear strength results and their components (i.e. Cohesion and internal angle of friction) were correlated with physical properties of samples (i.e. grading coefficient of curvature, coefficient of uniformity, and density). Results showed that samples classified as well-graded and dense sand had higher shear strength. In the other hand, the shear strengths decreased when the mixtures became poorly-graded and less dense. The inclusion of the clay fraction increased cohesion component and decreased internal angle of friction.

  18. Long-term monitoring of nitrate transport to drainage from three agricultural clayey till fields

    DEFF Research Database (Denmark)

    Ernstsen, Vibeke; Olsen, Preben; Rosenbom, Annette E.

    2015-01-01

    -regulation in future. This study strives to provide such knowledge by evaluating on 11 years of nitrate-N con-centration measurements in drainage from three subsurface-drained clayey till fields (1.3–2.3 ha) representing approxi-mately 71 % of the surface sediments in Denmark dominated by clay. The fields differ...... in their inherent hydrogeological field settings (e.g. soil-type, geology, climate, drainage and groundwater table) and the agricultural management of the fields (e.g. crop type, type of N fertilisers and agricultural practices). The evaluation revealed three types of clayey till fields characterised by: (i) low net...... precipitation, high concen-tration of nitrate-N, and short-term low intensity drainage at air temperatures often below 5 ◦C; (ii) medium net precip-itation, medium concentration of nitrate-N, and short-term medium-intensity drainage at air temperatures often above 5 ◦C; and (iii) high net precipitation, low...

  19. In-situ monitoring of deformation of clayey and volcanic sequences in the lacustrine plain of Iztapalapa, Mexico City

    Science.gov (United States)

    Carreon-Freyre, D.; Cerca, M.; Barrientos, B.; Gutierrez, R.; Blancas, D.

    2012-12-01

    Major cities of Central Mexico with lowering of land elevation problems are located in inter-volcanic and fault bounded basins within the central Trans-Mexican Volcanic Belt (TMVB). The most representative and studied case of ground deformation is Mexico City, where the Iztapalapa Municipality presents the highest population density. This area is located over the geological contact between the "Sierra de Santa Catarina" volcanic range and a lacustrine plain. Filling of lacustrine basins includes silty and clayey sediments as well as pyroclastic deposits (coarse and fine grained) and volcanic rocks layers. We used Ground Penetrating Radar (GPR) and MASW prospection to evaluate contrasts in the physical properties of fine grained soils and identify geometry of the deformational features and implemented a mechanical system for in situ monitoring in fractured sites. Deformational features in this basin reflect an interplay between the geological history (depositional conditions), load history, seismic activity, and faulting. Plastic mechanical behaviour predominates in these clayey sediments and differential deformation locally triggers brittle fracturing and/or subsidence of the surface. In this work we present the results of monitoring and characterization of ground deformation and fracturing in different sequences, our results show a dynamic interplay between the mechanisms of ground fracturing and the stress history of sedimentary sequences. Relating the mechanical behaviour of the studied sequences with variations of physical and geological properties should be taken into account to estimate land level lowering and risk of fracturing for urban development planning.

  20. US downstream consolidation and bifurcation

    International Nuclear Information System (INIS)

    Adam, P.S.

    1997-01-01

    Several years of dismal performances finally prompted US petroleum marketers and refiners to consolidate in a big way, starting last year. This restructuring is already altering the configuration and dynamics of marketing and refining in North America. In the years ahead, returns seem set to improve industry-wide. But a rising tide of marketing and refining profitability will not lift all the boats, at least not all equally, particularly since there may be more to some of these recent alliances, partnerings, divestitures and mergers than first meets the eye. A more concentrated US refining and marketing sector might mean more fireworks rather than greater stability. (author)

  1. Influence of preconsolidation on consolidation quality after stamp forming of C/PEEK composites

    Science.gov (United States)

    Slange, T. K.; Warnet, L.; Grouve, W. J. B.; Akkerman, R.

    2016-10-01

    Stamp forming is a rapid manufacturing technology used to shape flat blanks of thermoplastic composite material into three-dimensional components. Currently, expensive autoclave and press consolidation are used to preconsolidate blanks. This study investigates the influence of preconsolidation on final consolidation quality after stamp forming and explores the potential of alternative blank manufacturing methods that could reduce part costs. Blanks were manufactured using various blank manufacturing methods and subsequently were stamp formed. The consolidation quality both before and after stamp forming was compared, where the focus was on void content as the main measure for consolidation quality. The void content was characterized through thickness and density measurements, as well as by microscopy analysis. Results indicate that preconsolidation quality does have an influence on the final consolidation quality. This is due to the severe deconsolidation and limited reconsolidation during stamp forming. Nevertheless, the potential of automated fiber placement and ultrasonic spot welding as alternative blank manufacturing methods was demonstrated.

  2. High-energy, high-rate consolidation of tungsten and tungsten-based composite powders

    Energy Technology Data Exchange (ETDEWEB)

    Raghunathan, S.K.; Persad, C.; Bourell, D.L.; Marcus, H.L. (Center for Materials Science and Engineering, Univ. of Texas, Austin (USA))

    1991-01-20

    Tungsten and tungsten-based heavy alloys are well known for their superior mechanical properties at elevated temperatures. However, unalloyed tungsten is difficult to consolidate owing to its very high melting temperature (3683 K). The additions of small amounts of low-melting elements such as iron, nickel, cobalt and copper, facilitate the powder processing of dense heavy alloys at moderate temperatures. Energetic high-current pulses have been used recently for powder consolidation. In this paper, the use of a homopolar generator as a power source to consolidate selected tungsten and tungsten-based alloys is examined. Various materials were consolidated including unalloyed tungsten, W-Nb, W-Ni, and tungsten heavy alloy with boron carbide. The effect of process parameters such as pressure and specific energy input on the consolidation of different alloy systems is described in terms of microstructure and property relationships. (orig.).

  3. Osmotic consolidation of suspensions and gels

    International Nuclear Information System (INIS)

    Miller, K.T.; Zukoski, C.F.

    1994-01-01

    An osmotic method for the consolidation of suspensions of ceramic particles is demonstrated. Concentrated solutions of poly(ethylene oxide) are separated from a suspension of ceramic particles by a semipermeable membrane, creating a gradient in solvent chemical potential. Solvent passes from the suspension into the polymer solution, lowering its free energy and consolidating the suspension. Dispersions of stable 8-nm hydrous zirconia particles were consolidated to over 47% by volume. Suspensions of α-alumina in three states of aggregation (dispersed, weakly flocculated, and strongly flocculated) were consolidated to densities greater than or equal to those produced in conventional pressure filtration. Moreover, the as-consolidated alumina bodies were partially drained of fluid during the osmotic consolidation process, producing cohesive partially dried bodies with improved handling characteristics

  4. Auto consolidated cohesive sediments erosion

    International Nuclear Information System (INIS)

    Ternat, F.

    2007-02-01

    Pollutants and suspended matters of a river can accumulate into the sedimentary column. Once deposited, they are submitted to self-weight consolidation processes, ageing and burying, leading to an increase of their erosion resistance. Pollutant fluxes can be related to sedimentary fluxes, determined by threshold laws. In this work, an erosion threshold model is suggested by introducing a cohesion force into the usual force balance. A model of cohesion is developed on the basis of interactions between argillaceous cohesive particles (clays), particularly the Van der Waals force, whose parameterization is ensured by means of granulometry and porosity. Artificial erosion experiments were performed in a recirculating erosion flume with natural cored sediments where critical shear stress measurements were performed. Other analyses provided granulometry and porosity. The results obtained constitute a good database for the literature. The model is then applied to the experimental conditions and gives good agreement with measurements. An example of the accounting for self-weight consolidation processes is finally suggested, before finishing on a Mohr like diagram dedicated to soft cohesive sediment erosion. (author)

  5. Neuromodulation: acetylcholine and memory consolidation.

    Science.gov (United States)

    Hasselmo

    1999-09-01

    Clinical and experimental evidence suggests that hippocampal damage causes more severe disruption of episodic memories if those memories were encoded in the recent rather than the more distant past. This decrease in sensitivity to damage over time might reflect the formation of multiple traces within the hippocampus itself, or the formation of additional associative links in entorhinal and association cortices. Physiological evidence also supports a two-stage model of the encoding process in which the initial encoding occurs during active waking and deeper consolidation occurs via the formation of additional memory traces during quiet waking or slow-wave sleep. In this article I will describe the changes in cholinergic tone within the hippocampus in different stages of the sleep-wake cycle and will propose that these changes modulate different stages of memory formation. In particular, I will suggest that the high levels of acetylcholine that are present during active waking might set the appropriate dynamics for encoding new information in the hippocampus, by partially suppressing excitatory feedback connections and so facilitating encoding without interference from previously stored information. By contrast, the lower levels of acetylcholine that are present during quiet waking and slow-wave sleep might release this suppression and thereby allow a stronger spread of activity within the hippocampus itself and from the hippocampus to the entorhinal cortex, thus facilitating the process of consolidation of separate memory traces.

  6. Genesis and Development of Consolidated Financial Statements

    OpenAIRE

    Kostyantyn Bezverkhiy

    2015-01-01

    In the context of economy globalization it is the mission of consolidated financial statements to meet demands of users for financial information about activities of a company group as one company. The article is devoted to study of genesis and development of consolidated financial statements of companies. Historical prerequisites of genesis of consolidated financial statements are shown as well as factors which conduced to their spreading. The approaches are elucidated to preparation of cons...

  7. Control of Bank Consolidated Financial Statements Quality

    OpenAIRE

    Margarita S. Ambarchyan

    2013-01-01

    The author presents the multiple linear regression model of bank consolidated financial statements quality. The article considers six characteristics that can be used to estimate the level of bank consolidated financial statements quality. The multiple linear regression model was developed, using the results of point-based system of consolidated financial statements of thirty European bank and financial groups on the basis of the developed characteristics. The author offers to use the charact...

  8. Alternate Energy Sources for Thermalplastic Binding Agent Consolidation

    Energy Technology Data Exchange (ETDEWEB)

    Frame, B.J.

    1999-01-01

    A study was conducted to investigate microwave and electron beam technologies as alternate energy sources to consolidate fiber coated with a thermoplastic binding agent into preforms for composite molding applications. Bench experiments showed that both microwave and electron beam energy can produce heat sufficient to melt and consolidate a thermoplastic binding agent applied to fiberglass mat, and several two- and three-dimensional fiberglass preforms were produced with each method. In both cases, it is postulated that the heating was accomplished by the effective interaction of the microwave or electron beam energy with the combination of the mat preform and the tooling used to shape the preform. Both methods contrast with conventional thermal energy applied via infrared heaters or from a heated tool in which the heat to melt the thermoplastic binding agent must diffuse over time from the outer surface of the preform toward its center under a thermal gradient. For these reasons, the microwave and electron beam energy techniques have the potential to rapidly consolidate thick fiber preforms more efficiently than the thermal process. With further development, both technologies have the potential to make preform production more cost effective by decreasing cycle time in the preform tool, reducing energy costs, and by enabling the use of less expensive tooling materials. Descriptions of the microwave and electron beam consolidation experiments and a summary of the results are presented in this report.

  9. 20 CFR 702.345 - Formal hearings; consolidated issues; consolidated cases.

    Science.gov (United States)

    2010-04-01

    ...; consolidated cases. (a) When one or more additional issues are raised by the administrative law judge pursuant... Administrative Law Judge may consolidate such cases for hearing. ...; consolidated cases. 702.345 Section 702.345 Employees' Benefits EMPLOYMENT STANDARDS ADMINISTRATION, DEPARTMENT...

  10. 26 CFR 1.1502-3 - Consolidated tax credits.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 12 2010-04-01 2010-04-01 false Consolidated tax credits. 1.1502-3 Section 1... (CONTINUED) INCOME TAXES Consolidated Tax Liability § 1.1502-3 Consolidated tax credits. (a) Determination of...) Consolidated limitation based on amount of tax. (i) Notwithstanding the amount of the consolidated credit...

  11. 7 CFR 283.16 - Consolidation of issues.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 4 2010-01-01 2010-01-01 false Consolidation of issues. 283.16 Section 283.16... Claims of $50,000 or More § 283.16 Consolidation of issues. Similar issues involved in appeals by two or...) Disposition of consolidated issues. If the ALJ orders consolidation, the issues consolidated will be...

  12. 24 CFR 92.608 - Consolidated plan.

    Science.gov (United States)

    2010-04-01

    ... 24 Housing and Urban Development 1 2010-04-01 2010-04-01 false Consolidated plan. 92.608 Section 92.608 Housing and Urban Development Office of the Secretary, Department of Housing and Urban Development HOME INVESTMENT PARTNERSHIPS PROGRAM American Dream Downpayment Initiative § 92.608 Consolidated...

  13. Changing the countryside by land consolidation

    NARCIS (Netherlands)

    Benthem, Roelof Jan

    Land consolidation is a system of technical and legal measures for the improvement of farming conditions and land productivity. In western and central Europe, the execution of these land consolidation schemes causes great changes in the appearance of the countryside: existing landscape elements such

  14. 20 CFR 410.646 - Consolidated issues.

    Science.gov (United States)

    2010-04-01

    ... 20 Employees' Benefits 2 2010-04-01 2010-04-01 false Consolidated issues. 410.646 Section 410.646..., Finality of Decisions, and Representation of Parties § 410.646 Consolidated issues. When one or more additional issues are raised by the Administrative Law Judge pursuant to § 410.637, such issues may, in the...

  15. Bonding prediction in friction stir consolidation of aluminum alloys: A preliminary study

    Science.gov (United States)

    Baffari, Dario; Reynolds, Anthony P.; Li, Xiao; Fratini, Livan

    2018-05-01

    Friction Stir Consolidation (FSC) is a solid-state process that results in consolidation of metal powders or chips producing solid billet through severe plastic deformation and the solid-state bonding phenomena. This process can be used both for primary production and for metal scrap recycling. During the FSC process, a rotating die is plunged into a hollow chamber containing the finely divided, unconsolidated material to be processed. In this paper, a FEM numerical model for the prediction of the quality of the consolidated billet is presented. In particular, a dedicated bonding criterion that takes into account the peculiar process mechanics of this innovative technology is proposed.

  16. Convergence in anisotropic conditions: gallery behaviour in the Callovo-Oxfordian clayey layer in North-Eastern France

    International Nuclear Information System (INIS)

    Blanco Martin, L.; Hadj-Hassen, F.; Philippe, J.C.; Boidy, E.; Colombet, G.; Armand, G.

    2010-01-01

    Document available in extended abstract form only. Coyne et Bellier (Tractebel Engineering) has been supplying geotechnical services to Andra since 1994 regarding the feasibility for developing a repository for radioactive waste in a 490 m deep clayey formation at the Meuse/Haute-Marne site. Armines/Mines-ParisTech (French engineering school) has been an Andra scientific partner for several years due to its expertise in rock creep behaviour as well as in mining technologies. Throughout the different works carried out for Andra (especially the studies concerning the enlargement of the underground research laboratory), the behaviour of the Callovo-Oxfordian clayey were computed. These studies are used mainly for predicting the long-term behaviour of this layer. Lemaitre's rheological law (or modified Norton's law) has been used for such purposes. This time-dependent law is able to model the isotropic hardening of an elastic-viscoplastic solid by taking into account a non linear viscosity (γ) which Coyne et Bellier has decided to represent by means of a cone-shaped dash-pot element (stiffness increases during creep, cf. Eric Boidy's PhD). This hypothesis, together with that standing for 'long-term incompressibility' (viscoplastic deformation occurs at constant volume), allows the law be expressed by means of the second invariants of the stress (q) and strain (ε vp ) tensors. The rheological model when the long term behaviour takes place beyond a stress threshold (σ S ) is shown. Modelling works that use this law reproduce well convergence measurements as long as radial stresses around the galleries are isotropic. When the stress field around the gallery is anisotropic, the classic Lemaitre's law no longer fits the convergence measurements. This is the case for the GMR gallery at the main level of the laboratory: the horizontal stress is 1.3 times greater than the vertical stress whilst the average vertical convergence is more than five

  17. Sealed source and device removal and consolidation feasibility study

    International Nuclear Information System (INIS)

    Ward, J.E.; Carter, J.G.; Meyers, R.L.

    1993-02-01

    The purpose of this study is to assess the feasibility of removing Greater-Than-Class C (GTCC) sealed sources from their containment device and consolidating them for transport to a storage or disposal facility. A sealed source is a sealed capsule containing a radioactive material that is placed in a device providing radioactive containment. It is used in the medical, industrial, research, and food-processing communities for calibrating, measuring, gauging, controlling processes, and testing. This feasibility study addresses the key operational, safety, regulatory, and financial requirements of the removal/consolidation process. This report discusses the process to receive, handle, repackage, and ship these sources to an interim or dedicated storage facility until a final disposal repository can be built and become operational (∼ c. 2010). The study identifies operational and facility requirements to perform this work. Hanford, other DOE facilities, and private hot-cell facilities were evaluated to determine which facilities could perform this work. The personnel needed, design and engineering, facility preparation, process waste disposal requirements, and regulatory compliance were evaluated to determine the cost to perform this work. Cost requirements for items that will have to meet future changing regulatory requirements for transportation, transportation container design and engineering, and disposal were not included in this study. The cost associated with in-process consolidation of the sealed sources reported in this study may have not been modified for inflation and were based on 1992 dollars. This study shows that sealed source consolidation is possible with minimal personnel exposure, and would reduce the risk of radioactive releases to the environment. An initial pilot-scale operation could evaluate the possible methods to reduce the cost and consolidate sources

  18. Clayey cap-rocks reactivity in presence of CO2 in deep geological storage conditions: experimentation/modeling integrated approach

    International Nuclear Information System (INIS)

    Credoz, A.

    2009-10-01

    CO 2 capture, transport and geological storage is one of the main solutions considered in the short and medium term to reduce CO 2 and others greenhouse gases emissions towards the atmosphere, by storing CO 2 in deeper geological reservoirs during 100 to 10 000 years. This Ph-D study offers a multi-scale vision of complex clayey cap-rocks reactivity and evolution. These formations are identified for the CO 2 containment and sealing into the reservoir. From the experimental scale on purified clay minerals to integrative modeling at high space and time scales, the strategy developed allowed identifying the main geochemical processes, to check the good agreement between experiment and modeling, and to lay emphasis the operational impacts on long-term cap-rocks integrity. Carbonated cements alteration is likely to open cap-rock porosity and to create preferential reactive pathway for reactive fluid flow. Besides, this could alter the cap-rock structure and the global geo-mechanic properties. Clay minerals alteration, including the illitization process, reduces the clay fraction volume but considerably limits the porosity increase. The illitization process in acidic conditions determined experimentally and by modeling at low and high scale, is coupled with silica precipitation. The final porosity increase control results of these two reactive processes balance. By a fundamental side, this study reveals new kinetic parameters of clay minerals and highlights new structural transformations. By an operational side, this study contributes to the acquisition of qualitative data (long-term reactive pathways of clayey cap-rocks, coupled reactivity carbonates/clays) and quantitative data (CO 2 penetration distance into the cap-rock) to partly answer to the performance and safety assessment CO 2 capture and geological storage. (author)

  19. Is autism partly a consolidation disorder?

    Science.gov (United States)

    Femia, Lisa A; Hasselmo, Michael E

    2002-12-01

    Computational modeling has been useful for understanding processes of encoding and consolidation in cortical structures. In particular, this work suggests a role of neuromodulators in setting dynamics for consolidation processes during different stages of waking and sleep. Because autistic individuals show symptoms of a cognitive nature coupled with a high prevalence of comorbid conditions such as epileptiform discharge during sleep and sleep disorders, it is possible that autism could involve a breakdown in consolidation processes, which are essential to build effective cognitive representations of the environment on the basis of individual experiences. In this article, theories of consolidation during different stages of waking and sleep and the role of different neuromodulators in these consolidation processes are reviewed in conjunction with different features of autism, which may be understood in the context of these theories.

  20. SOME APECTS REGARDING THE CONSOLIDATED FINANCIAL STATEMENTS

    Directory of Open Access Journals (Sweden)

    Szora Tamas Atila

    2012-12-01

    Full Text Available The study is divided into four parts: in the introduction are presented the theoretical aspects of the consolidated financial statements and the consolidation methods. During the second part are shown the structure rates calculated prior and after the consolidation, and in the third are calculated the financial rates of return and the effective tax rates of fixed assets. The conclusion of this study presents that although the consolidated entity is not a tax, it presents the group effort without the internal flows between entities within the group. In terms of the world scientific research typology used by the authors, it refers to descriptive research, explanatory research and applied research. In terms of the novelties, brought by this study, it is specifically determined, based on the actual database, the evolution of structure indicators, indicators of balance, the financial profitability indicators of corporate companies prior to and after consolidation.

  1. Control of Bank Consolidated Financial Statements Quality

    Directory of Open Access Journals (Sweden)

    Margarita S. Ambarchyan

    2013-01-01

    Full Text Available The author presents the multiple linear regression model of bank consolidated financial statements quality. The article considers six characteristics that can be used to estimate the level of bank consolidated financial statements quality. The multiple linear regression model was developed, using the results of point-based system of consolidated financial statements of thirty European bank and financial groups on the basis of the developed characteristics. The author offers to use the characteristic significance factor in the process of consolidated financial statements appraisal by points. The constructed regression model is checked on accuracy and statistical significance. The model can be used by internal auditors and financial analytics as an instrument for bank and non-bank consolidated financial statements quality control

  2. Initial Assessment of the Consolidation of Chalcogels into a Viable Waste Form

    Energy Technology Data Exchange (ETDEWEB)

    Riley, Brian J.; Lepry, William C.

    2012-08-31

    This report provides some preliminary data for the consolidation of chalcogen-based aerogels. The chalcogels tested to date at PNNL show great promise as iodine sorbents and preliminary consolidation research shows that they can be melted into a phase-pure glass at moderate temperatures. The preliminary consolidation experiments show that these materials might attack fused quartz so an alternative crucible material will likely need to be used to prevent this. The next steps will be to • Consider melting other chalcogel chemistries, e.g., Sn-Sb-S, Ge-Sn-S chalcogels • Consider melting chalcogels with adsorbed iodine to monitor iodine loss during melting • Optimize the consolidation temperatures to minimize the iodine loss and volatilization

  3. Water states and types of water in materials from different argillaceous formations

    International Nuclear Information System (INIS)

    Fernandez, A.M.; Melon, A.

    2010-01-01

    Document available in extended abstract form only. Depending of their structure and degree of compaction, clays can be hydrated by a variable amount of water molecules in the inter-lamellar space and on external surfaces. Due to the fact that the structure and nature of water molecules (properties of liquid water) is influenced by the clay surfaces; different types of waters are involved in clayey systems (internal/external water, adsorbed/free water) giving a double porosity structure. The water volume accessible to ions is a key parameter in order to determine the pore water chemistry affecting the radionuclide transport in clay-rocks. In the case of argillaceous formations, natural consolidation induces significant physical and structural changes to clays as a function of time, leading to a progressive compaction and agglomeration of particles, reduction of crystallinity and an increase of micro-strain, which affects both the tetrahedral and octahedral layers. Structure and dynamics of water are modified when water molecules are close to interfaces or confined in porous spaces. At high degrees of compaction, the diffusive transport of the solvated ions and the solvent molecules in clays is substantially retarded compared with the free electrolyte solution because of the surface complexation of ions and the strong ordering of solvent molecules at the solid-liquid interface. Besides, mud-rocks contain a variable amount of different types of clays, such as illite, kaolinite, chlorites, smectite and illite/smectite mixed layers; as well as other main and accessory minerals which influence also the amount of water adsorbed and types of waters in these systems. Structural and dynamic properties of water confined among basal planes of clays have been extensively studied by means of water adsorption isotherms, neutron scattering, molecular dynamics (MD) and Monte- Carlo simulations. However, most of the works are related to purified clays and dispersed systems. In real

  4. Consolidation and atmospheric drying of fine oil sand tailings : Comparison of blind simulations and field scale results

    NARCIS (Netherlands)

    Vardon, P.J.; Yao, Y.; van Paassen, L.A.; van Tol, A.F.; Sego, D.C.; Wilson, G.W.; Beier, N.A.

    2016-01-01

    This paper presents a comparison between blind predictions of field tests of atmospheric drying of mature fine tailings (MFT) presented in IOSTC 2014 and field results. The numerical simulation of the consolidation and atmospheric drying of selfweight consolidating fine material is challenging and

  5. Effect of nanostructured lime-based and silica-based products on the consolidation of historical renders

    NARCIS (Netherlands)

    Borsoi, G.; Veiga, R.; Santos Silva, A.

    2013-01-01

    An important operation for the conservation of historical renders is the cohesion restitution of the binderaggregate system, based on the use of materials with consolidating properties. Inorganic consolidants are usually preferred to organic ones due to better compatibility and durability. The aim

  6. Nuclear weapons complex. Weaknesses in DOE's nonnuclear consolidation plan

    International Nuclear Information System (INIS)

    Wells, James E. Jr.; Fenzel, William F.; Schulze, John R.; Gaffigan, Mark E.

    1992-11-01

    Nuclear weapons contain a wide variety of nonnuclear components - items that are not made from nuclear materials. These components comprise the majority of parts in nuclear weapons, including the ones needed to guide weapons to their targets, initiate the nuclear explosion, increase the weapons' explosive yield, and ensure the weapons' safety and security. DOE has three facilities, the Kansas City Plant in Missouri, the Mound Plant in Ohio, and the Pinellas Plant in Florida, that are dedicated primarily to nonnuclear activities and have unique manufacturing responsibilities. Some additional nonnuclear manufacturing activities are performed at the Rocky Flats Plant in Colorado, the Y-12 Plant in Tennessee, and the Pantex Plant in Texas. Descriptions of each plant and the activities they conduct are contained in appendix I of this report. In 1991, DOE began planning to reconfigure the nuclear weapons complex into one that is smaller, less diverse, and less expensive to operate. More specifically, DOE issued a reconfiguration study in January 1991 that set forth a detailed framework for making the complex smaller and more efficient. The study will lead to a complex-wide Programmatic Environmental Impact Statement (PEIS) on how best to reconfigure the complex. This statement is planned to be completed in late 1993. As part of the effort to analyze the reconfiguration, DOE's Assistant Secretary for Defense Programs directed the Albuquerque Operations Office in April 1991 to develop a nonnuclear consolidation plan to serve as input to the PEIS. There are a number of weaknesses in DOE's NCP. First, because the NCP's scope was limited to examining single-site consolidation alternatives, the decision to select Kansas City as the preferred option was made without analyzing other nonnuclear options. These options included down sizing and modernizing all facilities in place or maximizing consolidation by eliminating all nonnuclear sites and relocating their functions to a

  7. Solid state consolidation nanocrystalline copper-tungsten using cold spray

    Energy Technology Data Exchange (ETDEWEB)

    Hall, Aaron Christopher [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Sarobol, Pylin [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Argibay, Nicolas [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Clark, Blythe [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Diantonio, Christopher [Sandia National Lab. (SNL-CA), Livermore, CA (United States); Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-09-01

    It is well known that nanostructured metals can exhibit significantly improved properties compared to metals with conventional grain size. Unfortunately, nanocrystalline metals typically are not thermodynamically stable and exhibit rapid grain growth at moderate temperatures. This severely limits their processing and use, making them impractical for most engineering applications. Recent work has shown that a number of thermodynamically stable nanocrystalline metal alloys exist. These alloys have been prepared as powders using severe plastic deformation (e.g. ball milling) processes. Consolidation of these powders without compromise of their nanocrystalline microstructure is a critical step to enabling their use as engineering materials. We demonstrate solid-state consolidation of ball milled copper-tantalum nanocrystalline metal powder using cold spray. Unfortunately, the nanocrystalline copper-tantalum powder that was consolidated did not contain the thermodynamically stable copper-tantalum nanostructure. Nevertheless, this does this demonstrates a pathway to preparation of bulk thermodynamically stable nanocrystalline copper-tantalum. Furthermore, it demonstrates a pathway to additive manufacturing (3D printing) of nanocrystalline copper-tantalum. Additive manufacturing of thermodynamically stable nanocrystalline metals is attractive because it enables maximum flexibility and efficiency in the use of these unique materials.

  8. Inorganic treatments for the consolidation and protection of stone artefacts

    Directory of Open Access Journals (Sweden)

    Mauro Matteini

    2008-04-01

    Full Text Available Consolidation and protection are two of the principal kinds of treatments through which the decay of old statues, stone facades, plasters and mural paintings caused by both natural atmospheric agents and, above all in the last five decades, by atmospheric pollution, is faced. The most traditional approach has been and is mainly based on the use of organic polymeric materials. They offer the advantage of easy application procedures and the possibility to obtain, at short times, very satisfying results. Different is their behaviour at long times. Some drawbacks come out over time both under the esthetical point of view as well as to the durability, compatibility and efficacy. Particularly critical is the situation when porous materials and soluble salts - gypsum above all - are simultaneously present. In such a situation inorganic treatments demonstrate to be much more appropriate. They assure durable and compatible results. In the present paper two of the most efficient and appropriate inorganic methods are reviewed in detail: the barium hydroxide method, both as desulfating and consolidating agent, and the ammonium oxalate method as passivating agent, consolidant and as a treatment capable of improving the natural colour contrast of the stone, when it is lost due to decay processes.

  9. Synthesis and investigation of sorbing materials based on natural and synthetic dispersed oxide systems for sorbing active leaching products of lava-like fuel-containing materials

    International Nuclear Information System (INIS)

    Kryip, Yi.M.; Shimchuk, T.V.; Tokarchuk, M.V.; Tokarchuk, M.V.

    2004-01-01

    Laboratory sorbent samples were synthesized on the basis of modified natural clayey raw material and fumed silica. Using chemical methods, composition of synthesized sorbents was established. Oxide and hydroxide structures, plated on the fumed silica and natural montmorillonite clay surface were identified. A forecast about sorbing properties of synthesized materials is made

  10. The Role of Fine Sediment Content on Soil Consolidation and Debris Flows Development after Earthquake

    Science.gov (United States)

    Lyu, L.; Xu, M., III; Wang, Z.

    2017-12-01

    Fine sediment has been identified as an important factor determining the critical runoff that initiates debris flows because its contribution to shear strength through consolidation. Especially, owing to the 2008 Wenchuan earthquake in China enormous of loose sediment with different fractions of fine particles was eroded and supplied as materials for debris flows. The loose materials are gradually consolidated along with time, and therefore stronger rainfall is required to overcome the shear strength and to initiate debris flows. In this study, flume experiments were performed to explore soil consolidation and shear strength on mass failure and debris flow initiation under the conditions that different fractions of fine sediment were contained in the materials. Under the low content of fine sediment conditions (mass percentages: 0-10%), the debris flows formed with large pores and low shear strength and thus fine particles were too few to fill up the pores among the coarse particles. The consolidation rate was mostly influenced by the content of the fine particles. Consolidation of fine particles caused an increase of the shear strength and decrease of the rainfall infiltration, and therefore, debris flow initiation required stronger rainfall as the consolidation of the fine particles developed.

  11. Analytical study on the suitability of using bentonite coated gravel as a landfill liner material

    International Nuclear Information System (INIS)

    Roberts, Anel A.; Shimaoka, Takayuki

    2008-01-01

    This study investigates the feasibility of using bentonite coated gravel (BCG) as a liner material for waste landfills. BCG has proven to be a very effective capping material/method for the remediation of contaminated sediments in aquatic environments. The concept of BCG is similar to that of peanuts/almonds covered with chocolate; each aggregate particle has been covered with the clayey material. Laboratory tests were aimed at evaluating regulated and non-regulated factors for liner materials, i.e., permeability and strength. Tests included X-ray diffraction, methylene blue absorption, compaction, free swelling, permeability, 1D consolidation, triaxial compression and cone penetration. The compactive efforts used for this study were the reduced Proctor, standard Proctor, intermediate Proctor, modified Proctor and super modified Proctor. The compactive energy corresponding to each effort, respectively, is as follows: 355.5, 592.3, 1196.3, 2693.3, and 5386.4 kJ/m 3 . Results revealed that even though aggregate content represents 70% of the weight of the material, hydraulic conductivities as low as 6 x 10 -10 cm/s can be achieved when proper compactive efforts are used. Compressibility is very low for this material even at low (or no) compactive efforts. Results also demonstrated how higher compactive efforts can lower the permeability of BCG; however, over-compaction creates fractures in the aggregate core of BCG that could increase permeability. Moreover, higher compactive efforts create higher swelling pressures that could compromise the performance of a barrier constructed using BCG. As a result of this study, moderate compactive efforts, i.e., intermediate Proctor or modified Proctor, are recommended for constructing a BCG barrier. Using moderate compactive efforts, very low hydraulic conductivities, good workability and good trafficability are easily attainable

  12. Evaluation consolidated under Financial Group Banca Transilvania

    Directory of Open Access Journals (Sweden)

    Chebac Neculina

    2009-06-01

    Full Text Available One of the components of prudence measures adopted by the competentauthorities with the regulation and supervision of financial markets at national andEuropean level is mandatory consolidation of accounts. Romania as member of theEuropean Union it harmonized national regulations with the European consolidation ofaccounts of companies. For the banks have been issued by the appropriate rules by theregulators authority, concerned by National Bank of Romania. In accordance withnational regulations, companies are required to prepare annual consolidated financialstatements may make such situations according to the regulations or accounting inaccordance with Directive VII of the European Economic Community, underInternational Financial Reporting Standards.

  13. Apparatus for consolidation of earth formations

    Energy Technology Data Exchange (ETDEWEB)

    Brandt, H

    1968-02-08

    Earth formations are consolidated by injecting into the formation a fluid medium through vertically spaced perforations; a device lowered into the borehole permits creating chambers isolated from each other and communicating with only one, or a group of perforations. These chambers are connected through valved conduits to a reservoir of the consolidating medium. Each chamber or each group of chambers has its own supply conduit, and flow-measuring means are provided in each conduit. The valves may be magnetic valves, controlled electrically from the surface; the reservoirs for the consolidating medium may be equipped with hydraulically actuated pistons. (8 claims)

  14. Physical and chemical factors affecting sludge consolidation

    Energy Technology Data Exchange (ETDEWEB)

    Turner, C.W.; Blimkie, M.E.; Lavoie, P.A

    1997-09-01

    Chemical reactions between sludge components and precipitation reactions within the pores of the existing sludge are shown to contribute to the consolidation of sludge under steam generator operating conditions. Simulations of sludge representative of plants with a mixed iron/copper feedtrain suggest that as the conditions in the feedtrain become more oxidizing the sludge will become harder with a higher nickel ferrite content. The precipitation of feedwater impurities introduced by condenser leaks and of zinc silicate, which is produced in plants with brass condenser tubes and silica in the makeup water, contribute significantly to sludge consolidation. Sodium phosphate is also shown to be an agent of sludge consolidation. (author)

  15. Deconsolidation and combustion performance of thermally consolidated propellants deterred by multi-layers coating

    Directory of Open Access Journals (Sweden)

    Zheng-gang Xiao

    2014-06-01

    Full Text Available Both heating and solvent-spray methods are used to consolidate the standard grains of double-base oblate sphere propellants plasticized with triethyleneglycol dinitrate (TEGDN (TEGDN propellants to high density propellants. The obtained consolidated propellants are deterred and coated with the slow burning multi-layer coating. The maximum compaction density of deterred and coated consolidated propellants can reach up to 1.39 g/cm3. Their mechanic, deconsolidation and combustion performances are tested by the materials test machine, interrupted burning set-up and closed vessel, respectively. The static compression strength of consolidated propellants deterred by multi-layer coating increases significantly to 18 MPa, indicating that they can be applied in most circumstances of charge service. And the samples are easy to deconsolidate in the interrupted burning test. Furthermore, the closed bomb burning curves of the samples indicate a two-stage combustion phenomenon under the condition of certain thickness of coated multi-layers. After the outer deterred multi-layer coating of consolidated samples is finished burning, the inner consolidated propellants continue to burn and breakup into aggregates and grains. The high burning progressivity can be carefully obtained by the smart control of deconsolidation process and duration of consolidated propellants. The preliminary results of consolidated propellants show that a rapid deconsolidation process at higher deconsolidation pressure is presented in the dynamic vivacity curves of closed bomb test. Higher density and higher macro progressivity of consolidated propellants can be obtained by the techniques in this paper.

  16. Distributed learning enhances relational memory consolidation.

    Science.gov (United States)

    Litman, Leib; Davachi, Lila

    2008-09-01

    It has long been known that distributed learning (DL) provides a mnemonic advantage over massed learning (ML). However, the underlying mechanisms that drive this robust mnemonic effect remain largely unknown. In two experiments, we show that DL across a 24 hr interval does not enhance immediate memory performance but instead slows the rate of forgetting relative to ML. Furthermore, we demonstrate that this savings in forgetting is specific to relational, but not item, memory. In the context of extant theories and knowledge of memory consolidation, these results suggest that an important mechanism underlying the mnemonic benefit of DL is enhanced memory consolidation. We speculate that synaptic strengthening mechanisms supporting long-term memory consolidation may be differentially mediated by the spacing of memory reactivation. These findings have broad implications for the scientific study of episodic memory consolidation and, more generally, for educational curriculum development and policy.

  17. Rate type isotach compaction of consolidated sandstone

    NARCIS (Netherlands)

    Waal, J.A. de; Thienen-Visser, K. van; Pruiksma, J.P.

    2015-01-01

    Laboratory experiments on samples from a consolidated sandstone reservoir are presented that demonstrate rate type compaction behaviour similar to that observed on unconsolidated sands and soils. Such rate type behaviour can have large consequences for reservoir compaction, surface subsidence and

  18. Consolidated Audit And Compliance System (CACS)

    Data.gov (United States)

    US Agency for International Development — Consolidated Audit and Compliance System: is an audit findings management and reporting system. CACS is an implementation of the Agency Secure Image and Storage...

  19. Relation Between Filtration and Soil Consolidation Theories

    OpenAIRE

    Strzelecki Tomasz; Strzelecki Michał

    2015-01-01

    This paper presents a different, than commonly used, form of equations describing the filtration of a viscous compressible fluid through a porous medium in isothermal conditions. This mathematical model is compared with the liquid flow equations used in the theory of consolidation. It is shown that the current commonly used filtration model representation significantly differs from the filtration process representation in Biot’s and Terzaghi’s soil consolidation models, which has a bearing on...

  20. Healthcare mergers and acquisitions: strategies for consolidation.

    Science.gov (United States)

    Zuckerman, Alan M

    2011-01-01

    The passage of federal healthcare reform legislation, in combination with other factors, makes it likely that the next few years will be a major period of consolidation for healthcare organizations. This article examines the seven key forces reshaping healthcare delivery--from insurance industry consolidation to cost inflation to the increasing gap between financially strong and struggling providers--and provides advice for organizations on both sides of an acquisition.

  1. The new wave of hospital consolidation.

    Science.gov (United States)

    Goldstein, Lisa

    2012-04-01

    Reimbursement challenges, spiraling healthcare costs, and a slow economic recovery are driving the latest wave of hospital consolidation. Health insurance companies and provider systems are forming partnerships in the consolidation field with the goal of reducing healthcare costs and improving quality. The "cost" of the acquisition may include debt and other obligations of the acquired hospital, such as pension liabilities, along with a multiyear capital commitment.

  2. SOME DISCLOSURE ASPECTS REGARDING CONSOLIDATED FINANCIAL STATEMENTS

    OpenAIRE

    Cirstea Andreea; Baltariu Carmen-Alexandra

    2013-01-01

    The purpose of this article is to analyze the current state of consolidated reporting practice harmonization concerning the choice of presenting the income statement, the changes in equity, the methods used for presenting the cash flow statement, the extant methods for evaluating and reporting goodwill, the extant methods in which jointly controlled entities are accounted in the consolidated financial statements, or the choice for recognizing investments in subsidiaries, jointly controlled en...

  3. Saskatchewan Energy Holdings Ltd. consolidated financial statements

    Energy Technology Data Exchange (ETDEWEB)

    1991-01-01

    The consolidated financial statements of Saskatchewan Energy Holdings Ltd. (formerly Saskatchewan Energy Corporation) as of December 31, 1990, and the consolidated statements of earnings and retained earnings and changes in cash position for the year are presented. Data include an inventory of supplies, natural gas in storage, property, plant and equipment. Financial statements are also presented for the year ending December 31, 1989, with comparative figures for the seven months ending December 31, 1988.

  4. Saskatchewan Energy Holdings Ltd. consolidated financial statements

    International Nuclear Information System (INIS)

    1991-01-01

    The consolidated financial statements of Saskatchewan Energy Holdings Ltd. (formerly Saskatchewan Energy Corporation) as of December 31, 1990, and the consolidated statements of earnings and retained earnings and changes in cash position for the year are presented. Data include an inventory of supplies, natural gas in storage, property, plant and equipment. Financial statements are also presented for the year ending December 31, 1989, with comparative figures for the seven months ending December 31, 1988

  5. [The consolidation of memory, one century on].

    Science.gov (United States)

    Prado-Alcala, R A; Quirarte, G L

    The theory of memory consolidation, based on the work published by Georg Elias Muller and Alfons Pilzecker over a century ago, continues to guide research into the neurobiology of memory, either directly or indirectly. In their classic monographic work, they concluded that fixing memory requires the passage of time (consolidation) and that memory is vulnerable during this period of consolidation, as symptoms of amnesia appear when brain functioning is interfered with before the consolidation process is completed. Most of the experimental data concerning this phenomenon strongly support the theory. In this article we present a review of experiments that have made it possible to put forward a model that explains the amnesia produced in conventional learning conditions, as well as another model related to the protection of memory when the same instances of learning are submitted to a situation involving intensive training. Findings from relatively recent studies have shown that treatments that typically produce amnesia when they are administered immediately after a learning experience (during the period in which the memory would be consolidating itself) no longer have any effect when the instances of learning involve a relatively large number of trials or training sessions, or relatively high intensity aversive events. These results are not congruent with the prevailing theories about consolidation.

  6. [Impacts of farmland consolidation on farmland landscape].

    Science.gov (United States)

    Deng, Jinsong; Wang, Ke; Li, Jun; Xu, Junfeng; Shen, Zhangquan; Gao, Yurong

    2006-01-01

    Farmland consolidation is the act of regulating, improving, and comprehensively renovating the structure, quality, and layout of field, water, road, forestry, and village in the countryside in a certain area by means of administration, economy, law, and engineering techniques according to the goal and usage defined by land use planning, so as to improve farmland use rate and its output rate, to increase farmland area, and to achieve better productive, living, and ecological environment. Recently, farmland consolidation has been carried out all over the country, especially in its economy-developed regions. But, unscientific planning and unsuitable farmland consolidation engineering have negative effects on field ecological system. In this paper, based on the technology of GIS and RS, the basic theories and methods of landscape ecology and a compositive grading method were applied to analysis the dynamics of farmland landscape fragmentation in Tongxiang county. The results showed that the farmland landscape fragmentation in this county was strongly affected by consolidation. More attention should be paid to the protection of farmland landscape during consolidation, and to avoid or decrease the negative effects resulted from unscientific planning and unsuitable farmland consolidation engineering.

  7. Internal Controls and Compliance With Laws and Regulations for the Defense Business Operations Fund Consolidated Financial Statements for FY 1995

    National Research Council Canada - National Science Library

    Lane, Frederick

    1996-01-01

    ... No. 94-01, "Form and Content of Agency Financial Statements," November 16, 1993. In addition, we determined whether controls were adequate to ensure that the consolidated financial statements were free of material error...

  8. Teaching Consolidations Accounting: An Approach to Easing the Challenge

    Science.gov (United States)

    Murphy, Elizabeth A.; McCarthy, Mark A.

    2010-01-01

    Teaching and learning accounting for consolidations is a challenging endeavor. Students not only need to understand the conceptual underpinnings of the accounting requirements for consolidations, but also must master the complex accounting needed to prepare consolidated financial statements. To add to the challenge, the consolidation process is…

  9. Pathway Distiller - multisource biological pathway consolidation.

    Science.gov (United States)

    Doderer, Mark S; Anguiano, Zachry; Suresh, Uthra; Dashnamoorthy, Ravi; Bishop, Alexander J R; Chen, Yidong

    2012-01-01

    One method to understand and evaluate an experiment that produces a large set of genes, such as a gene expression microarray analysis, is to identify overrepresentation or enrichment for biological pathways. Because pathways are able to functionally describe the set of genes, much effort has been made to collect curated biological pathways into publicly accessible databases. When combining disparate databases, highly related or redundant pathways exist, making their consolidation into pathway concepts essential. This will facilitate unbiased, comprehensive yet streamlined analysis of experiments that result in large gene sets. After gene set enrichment finds representative pathways for large gene sets, pathways are consolidated into representative pathway concepts. Three complementary, but different methods of pathway consolidation are explored. Enrichment Consolidation combines the set of the pathways enriched for the signature gene list through iterative combining of enriched pathways with other pathways with similar signature gene sets; Weighted Consolidation utilizes a Protein-Protein Interaction network based gene-weighting approach that finds clusters of both enriched and non-enriched pathways limited to the experiments' resultant gene list; and finally the de novo Consolidation method uses several measurements of pathway similarity, that finds static pathway clusters independent of any given experiment. We demonstrate that the three consolidation methods provide unified yet different functional insights of a resultant gene set derived from a genome-wide profiling experiment. Results from the methods are presented, demonstrating their applications in biological studies and comparing with a pathway web-based framework that also combines several pathway databases. Additionally a web-based consolidation framework that encompasses all three methods discussed in this paper, Pathway Distiller (http://cbbiweb.uthscsa.edu/PathwayDistiller), is established to allow

  10. RTE - Consolidated financial statements 2016

    International Nuclear Information System (INIS)

    2017-01-01

    RTE's business model led to favourable borrowing conditions. In April 2016, RTE launched a 1 350 million euro bond issue in two tranches, one for 650 million euro at a rate of 1% over 10.5 years, the other for 700 million euro at a rate of 2% over 20 years. These historically low rates extend the average debt maturity and keep financial costs under control. This document comprises a Management report with RTE's Financial and legal information, Company information, Environmental and societal information, and a Consolidated financial statement with detailed financial data and comments

  11. Behavior of two phenyl urea herbicides in clayey soils and effect of alternating dry-wet conditions on their availability.

    Science.gov (United States)

    Haouari, Jamila; Dahchour, Abdelmalek; Peña-Heras, Arancha; Louchard, Xzavier; Lennartz, Berndt; Alaoui, Mohamed Elbelghiti; Satrallah, Ahmad

    2006-01-01

    Adsorption and mobility of linuron (3-(3,4-dichlorophenyl)-1-methoxy-1-methylurea) and diuron (3-(3,4-dichlorophenyl)-1, 1-dimethylurea) were studied in clayey soils from the Gharb area (Morocco). Soils A and B were planted with sun flower (Helianthus annuus) while soil C was planted with sugar cane (Saccharum offcinarum). Adsorption was studied for linuron in soils A and B, while mobility was studied only in soil B. Adsorption data were found to fit the Freundlich equation with correlation coefficients r2 > 0.9. Freundlich coefficients (Kf, nf) were in agreement with L and S isotherm types for soils A and B, respectively. Values of Koc (195 and 102) indicate moderate adsorption. Desorption isotherms for linuron showed hysteresis for both soils. The pesticide would be more bound to soil A (H = 8.44) than to soil B (H = 4.01). The effect of alternating wet and dry conditions was tested for soils A and B. Results showed that retention would increase in soil subject to an additional wet and dry cycle. In the case of diuron isotherm was of type L in soil C. Desorption was noticeable at high concentrations and tended to decrease when concentrations diminished. Mobility of linuron was tested in polyvinyle chloride (PVC) columns, which received different treatments before their percolation. The pesticide was more mobile in a previously saturated column. In columns subject to a drying step after saturation with water, linuron mobility was greatly reduced.

  12. Particles and solutes migration in porous medium : radionuclides and clayey particles simultaneous transport under the effect of a salinity gradient

    International Nuclear Information System (INIS)

    Faure, M.H.

    1994-01-01

    This work deals with the radiation protection of high-level and long-life radioactive waste storages. The colloids presence in ground waters can accelerate the radionuclides migration in natural geological deposits. The aim of this thesis is then to control particularly the particles motion in porous medium in order to anticipate quantitatively their migration. Liquid chromatography columns are filled with a clayey sand and fed with a decreasing concentration sodium chloride solution in order to study the particles outlet under a salinity gradient. When the porous medium undergoes a decrease of salinity it deteriorates. The adsorption of the cations : sodium 22, calcium 45, cesium 137 and neptunium 237 is then studied by the ions exchange method. The radionuclide solution is injected before the decrease of the feed solution salinity. The decrease of the sodium chloride concentration leads to the decrease of the radionuclides concentration because the adsorption competition between the sodium ion and the injected cation is lower. The particles transport, without fouling of the porous medium, is carried out in particular physical and chemical conditions which are described. (O.L.). 71 refs., 105 figs., 26 tabs

  13. Effect of clayey groundwater on the dissolution rate of SON68 simulated nuclear waste glass at 70 °C

    Science.gov (United States)

    De Echave, T.; Tribet, M.; Jollivet, P.; Marques, C.; Gin, S.; Jégou, C.

    2018-05-01

    To predict the long-term behavior of high-level radioactive waste glass, it is necessary to study aqueous dissolution of the glass matrix under geological repository conditions. The present article focuses on SON68 (an inactive surrogate of the R7T7 glass) glass alteration in synthetic clayey groundwater at 70 °C. Experiments in deionized water as reference were also performed in the same conditions. Results are in agreement with those of previous studies showing that magnesium present in the solution is responsible for higher glass alteration. This effect is transient and pH-dependent: Once all the magnesium is consumed, the glass alteration rate diminishes. Precipitation of magnesium silicate of the smectite group seems to be the main factor for the increased glass alteration. A pH threshold of 7.5-7.8 was found, above which precipitation of these magnesium silicates at 70 °C is possible. TEM observations reveal that magnesium silicates grow at the expense of the passivating gel, which partly dissolves, forming large pores which increase mass transfer between the reacting glass surface and the bulk solution.

  14. A laboratory feasibility study on a new electrokinetic nutrient injection pattern and bioremediation of phenanthrene in a clayey soil

    International Nuclear Information System (INIS)

    Xu Wei; Wang Cuiping; Liu Haibin; Zhang Zhiyuan; Sun Hongwen

    2010-01-01

    Electrokinetic (EK) injection has recently been proposed to supply nutrients and electron acceptors in bioremediation of low permeable soils. However, effective pH control and uniform injection of inorganic ions have yet to be developed. The present study investigated a new EK injection pattern, which combined electrolyte circulation and electrode polarity reversal on a clayey soil. Soil pH could be controlled ranging from 7.0 to 7.6 by circulating the mixed electrolyte at a suitable rate (800 mL/h in this study) without any buffer. Ammonium and nitrate ions were distributed more uniformly in soil by electrode polarity reversal. The developed electrokinetic injection technology was applied primarily in bioremediation of phenanthrene contaminated soil. Over 80% of the initial 200 mg/kg phenanthrene in soil could be removed in 20 d, and greater phenanthrene removal was achieved using electrode polarity reversal. Hence, the present study provides a promising electrokinetic injection technology for bioremediation of contaminated soils.

  15. Consolidation Processes: Raiders & Targets in Polish Financial Institutions

    OpenAIRE

    Poteraj, Jarosław

    2004-01-01

    The work consists of five chapters, an annex and an appendix. In the first chapter the author describes the point of consolidation processes, presents: the meaning of consolidation processes, active and institutional aspects of merger execution, gives a classification of the consolidation processes and considers conditions of execution of consolidations processes in the Polish law, The next chapter concerns reasons of consolidation processes. The author describes there in turn: motives of the...

  16. The consolidation of annual accounts in the Swiss Federal Government

    OpenAIRE

    Vollenweider, Petra

    2011-01-01

    Financial reporting in the public sector is influenced by the private sector accounting standards. The Swiss Federal Government has recently started to prepare consolidated financial statements. The purpose of this study is to describe how the Swiss Federal Government is doing its consolidated financial statements. Theoretically there are different consolidation theories and methods. The choice of consolidation method can explain which consolidation theory is used when the financial statement...

  17. Comparison of performance of concrete barriers in a clayey geological medium

    International Nuclear Information System (INIS)

    Trotignon, Laurent; Peycelon, Hugues; Bourbon, Xavier

    2006-01-01

    Cement based materials play an important role in the design and performance of future deep radioactive waste disposals. The type of materials selected for engineered barrier systems (EBS) is an important issue: protection of waste packages against corrosion and chemical degradation may be greatly enhanced by a proper choice and dimensioning. The long-term geochemical performance of two concrete types, CEM-I (pure Portland cement) and CEM-V (blended Portland, fly ash, blast furnace slag cement) was evaluated using reactive transport simulations of the interactions between the Callovo-Oxfordian mud-rock (argillite) and concrete EBS over periods up to 10 6 years at 25 deg. C. Simulations have been run with cylindrical geometry using the modeling tool Hytec 3.5 (ENSMP/CIG). Diffusion of solutes in the pore-water of the solid media was considered to be the dominant transport process. Different scenarios were studied, including the case of sulfate attack. Various assumptions on the transport properties of the EBS and the argillite medium have been considered and compared. The interactions between concrete, CEM-I or CEM-V, and mud-rock are in both cases predicted to lead to a significant clogging in the mud-rock, in the vicinity of the interface with the concrete EBS. However, the nature and extent of the EBS/mud-rock interface transformations greatly differ for the two materials considered. CEM-V, due to lower diffusion coefficients, keeps longer internal high pH conditions which are favorable to the waste packages from a chemical point of view. In addition, simulations predict that CEM-V material should have a better resistance to sulfate attack than CEM-I based barriers. In the case of CEM-I, the altered clay zone has a greater extent (up to 1.3 m in 400,000 y) and the drop of porosity is mainly due to zeolites and re-precipitated illite, quartz and calcite. For CEM-V, the altered clay zone is much smaller (less than 0.2 m in 400,000 y) and secondary smectite and

  18. Geotechnical properties of reinforced clayey soil using nylons carry’s bags by products

    Directory of Open Access Journals (Sweden)

    Salim Nahla

    2018-01-01

    Full Text Available All structures built on soft soil may experience uncontrollable settlement and critical bearing capacity. This may not meet the design requirements for the geotechnical engineer. Soil stabilization is the change of these undesirable properties in order to meet the requirements. Traditional methods of stabilizing or through in-situ ground improvement such as compaction or replacement technique is usually costly. Now a safe and economic disposal of industrial wastes and development of economically feasible ground improvement techniques are the important challenges being faced by the engineering community. This work focuses on improving the soft soil brought from Baghdad by utilizing the local waste material for stabilization of soil, such as by using “Nylon carry bag’s by product” with the different percentage and corresponding to 1 %, 3% and 5% (the portion of stabilizer matters to soil net weight of dried soil. The results indicated that as Nylon’s fiber content increases, the liquid limit decreases while the plastic limit increases, so the plasticity index decreases. Furthermore, the maximum dry density decreases while, the optimum moisture content increases as the Nylon’s fiber percentage increases. The compression index (decreases as the Nylon’s fiber increases and provides a maximum of 43% reduction by adding 5% nylon waste material. In addition, the results indicated that, the undrained shear strength increases as the nylon fiber increases.

  19. Dysfunctional overnight memory consolidation in ecstasy users.

    Science.gov (United States)

    Smithies, Vanessa; Broadbear, Jillian; Verdejo-Garcia, Antonio; Conduit, Russell

    2014-08-01

    Sleep plays an important role in the consolidation and integration of memory in a process called overnight memory consolidation. Previous studies indicate that ecstasy users have marked and persistent neurocognitive and sleep-related impairments. We extend past research by examining overnight memory consolidation among regular ecstasy users (n=12) and drug naïve healthy controls (n=26). Memory recall of word pairs was evaluated before and after a period of sleep, with and without interference prior to testing. In addition, we assessed neurocognitive performances across tasks of learning, memory and executive functioning. Ecstasy users demonstrated impaired overnight memory consolidation, a finding that was more pronounced following associative interference. Additionally, ecstasy users demonstrated impairments on tasks recruiting frontostriatal and hippocampal neural circuitry, in the domains of proactive interference memory, long-term memory, encoding, working memory and complex planning. We suggest that ecstasy-associated dysfunction in fronto-temporal circuitry may underlie overnight consolidation memory impairments in regular ecstasy users. © The Author(s) 2014.

  20. Effect of biodegradation on the consolidation properties of a dewatered municipal sewage sludge.

    Science.gov (United States)

    O'Kelly, Brendan C

    2008-01-01

    The effect of biodegradation on the consolidation characteristics of an anaerobically digested, dewatered municipal sewage sludge was studied. Maintained-load oedometer consolidation tests that included measurement of the pore fluid pressure response were conducted on moderately degraded sludge material and saturated bulk samples that had been stored under static conditions and allowed to anaerobically biodegrade further (simulating what would happen in an actual sewage sludge monofill or lagoon condition). Strongly degraded sludge material was produced after a storage period of 13 years at ambient temperatures of 5-15 degrees C, with the total volatile solids reducing from initially 70% to 55%. The sludge materials were highly compressible, although impermeable for practical purposes. Primary consolidation generally occurred very slowly, which was attributed to the microstructure of the solid phase, the composition and viscosity of the pore fluid, ongoing biodegradation and the high organic contents. The coefficient of primary consolidation values decreased from initially about 0.35m2/yr to 0.003-0.03m2/yr with increasing effective stress (sigmav'=3-100kPa). Initially, the strongly degraded sludge material was slightly more permeable, although both the moderately and strongly degraded materials became impermeable for practical purposes (k=10(-9)-10(-12)m/s) below about 650% and 450% water contents, respectively. Secondary compression became more dominant with increasing effective stress with a mean secondary compression index (Calphae) value of 0.9 measured for both the moderately and strongly degraded materials.

  1. Cooperation. An alternative to consolidation or bankruptcy.

    Science.gov (United States)

    Cady, G

    1994-04-01

    With all the recent consolidation and doomsaying within the EMS industry, the music from the movie "Jaws" is likely playing a constant refrain in the minds of many smaller EMS providers. The word from the consolidators--those large companies buying up small and midsized ambulance services--is that health maintenance organizations (HMOs) soon will be purchasing EMS and other "out-of-hospital" services and that since HMOs are for-profit institutions, they will be looking for the least expensive EMS delivery system. The consolidators and others with a stake in the new order assert that cost-effective services can only be produced by large national EMS companies; smaller companies will be left out in the cold. But will they?

  2. Consolidation equipment for irradiated nuclear fuel channels

    International Nuclear Information System (INIS)

    Taguchi, M.; Komatsu, Y.; Ose, T.

    1989-01-01

    The authors have developed and put into use a new type of mechanical consolidation equipment for irradiated nuclear fuel channels. This includes round-slice cutting of the top 100mm of the fuel channel with a guillotine cutter, and press cutting of the two corners of the remaining length of the fuel channel. Four guillotine blades work in combination with receiving blades arranged inside the fuel channel to cut the top 100mm, including the clips and spacers, of the fuel channel into a round slice. A press assembled in the consolidation equipment then presses the slice to achieve volume reduction. The press cutting operation uses two press cutting blades arranged inside the fuel channel and the receiving blades outside the fuel channel. The remaining length of fuel channel is cut off into L-shaped pieces by press cutting. This consolidation equipment is highly efficient because the round-slice cutting, pressing, and press cutting are all achieved by one unit

  3. Materialism.

    Science.gov (United States)

    Melnyk, Andrew

    2012-05-01

    Materialism is nearly universally assumed by cognitive scientists. Intuitively, materialism says that a person's mental states are nothing over and above his or her material states, while dualism denies this. Philosophers have introduced concepts (e.g., realization and supervenience) to assist in formulating the theses of materialism and dualism with more precision, and distinguished among importantly different versions of each view (e.g., eliminative materialism, substance dualism, and emergentism). They have also clarified the logic of arguments that use empirical findings to support materialism. Finally, they have devised various objections to materialism, objections that therefore serve also as arguments for dualism. These objections typically center around two features of mental states that materialism has had trouble in accommodating. The first feature is intentionality, the property of representing, or being about, objects, properties, and states of affairs external to the mental states. The second feature is phenomenal consciousness, the property possessed by many mental states of there being something it is like for the subject of the mental state to be in that mental state. WIREs Cogn Sci 2012, 3:281-292. doi: 10.1002/wcs.1174 For further resources related to this article, please visit the WIREs website. Copyright © 2012 John Wiley & Sons, Ltd.

  4. Consolidation and permeability of salt in brine

    International Nuclear Information System (INIS)

    Shor, A.J.; Baes, C.F. Jr.; Canonico, C.M.

    1981-07-01

    The consolidation and loss of permeability of salt crystal aggregates, important in assessing the effects of water in salt repositories, has been studied as a function of several variables. The kinetic behavior was similar to that often observed in sintering and suggested the following expression for the time dependence of the void fraction: phi(t) = phi(0) - (A/B)ln(1 + Bt/z(0) 3 ), where A and B are rate constants and z(0) is initial average particle size. With brine present, A and phi(0) varied linearly with stress. The initial void fraction was also dependent to some extent on the particle size distribution. The rate of consolidation was most rapid in brine and least rapid in the presence of only air as the fluid. A brine containing 5 m MgCl 2 showed an intermediate rate, presumably because of the greatly reduced solubility of NaCl. A substantial wall effect was indicated by an observed increase in the void fraction of consolidated columns with distance from the top where the stress was applied and by a dependence of consolidation rate on the column height and radius. The distance through which the stress fell by a factor of phi was estimated to change inversely as the fourth power of the column diameter. With increasing temperature (to 85 0 C), consolidation proceeded somewhat more rapidly and the wall effect was reduced. The permeability of the columns dropped rapidly with consolidation, decreasing with about the sixth power of the void fraction. In general, extrapolation of the results to repository conditions confirms the self-sealing properties of bedded salt as a storage medium for radioactive waste

  5. M-S-H precipitation in low-pH concretes in clayey environment

    International Nuclear Information System (INIS)

    Dauzeres, A.; Achiedo, G.; Nied, D.; L'Hopital, E.; Alahrache, S.; Lothenbach, B.

    2015-01-01

    In the framework of the CI-project (Cement Clay Interaction Experiment), two different low-pH cements were emplaced at Mont Terri rock laboratory to study their interactions with the surrounding Opalinus Clay (OPA): ESDRED (shotcrete mixture: 60% of CEM-I 42.5 N + 40% of silica fume + aluminium sulphate salt as accelerator) and LAC composed of CEM-III/B 42.5 L (60% of blast furnace slag + 10% nano silica). After 5 years of interactions in the Mont Terri rock laboratory, SEM-EDS analyses show a systematic Mg-perturbation associated with a high decalcification near the surface of both cementitious materials. TGA (Thermogravimetric Analysis) and XRD (X-ray diffraction) investigations associate this Mg-enrichment to the possible formation of M-S-H. This result is confirmed by 29 Si NMR analyses, showing a high polymerisation degree of the Si-network in the Mg-enriched zone typical of a sheet-like structure. Tem/EDS investigations of a FIB section carried out in the Mg zone of both LAC and ESDRED concretes indicate that the Mg phase exhibits a gel-like structure similar to C-S-H gel. This experimentally observed Mg-enrichment in the interaction zone is well reproduced by reactive transport modelling of the LAC/Opalinus clay with the HYTEC code. (authors)

  6. Strontium distribution and origins in a natural clayey formation (Callovian-Oxfordian, Paris Basin, France): a new sequential extraction procedure

    International Nuclear Information System (INIS)

    Lerouge, C.; Gaucher, E.C.; Tournassat, C.; Negrel, P.; Crouzet, C.; Guerrot, C.; Gautier, A.; Michel, P.; Vinsot, A.; Buschaert, S.

    2010-01-01

    Document available in extended abstract form only. Strontium is a minor element in the Callovian-Oxfordian clayey formation of Bure (ANDRA Underground Research laboratory, France) and may be interesting as a natural analogue of cationic radionuclides. The objective of our study was to better understand the chemical behaviour of this element since the sediment deposition. Previous mineralogical work showed that main strontium-bearing minerals in the clay-stones, in addition to clay minerals, are celestite, carbonates and accessory micas and K-feldspars. In order to establish the strontium distribution and determine its origins across the clayey formation and establish a strontium diffusion profile, a four step sequential extraction procedure combined with strontium isotopes was developed and adapted to the mineralogy of the Bure clay-stones. The four-steps sequential extraction developed and applied to sixteen samples of Callovian-Oxfordian clay-stones showed that the exchangeable fraction (27 to 48% of the total strontium) and the carbonate fraction (38-47% of the total strontium) are the two main fractions carrying the strontium, the detrital fraction being secondary (< 15%). Celestite is the major strontium-carrier mineral that can perturb the results of the sequential extraction but not significantly modify the distribution of strontium at the scale of the formation. The celestite was studied on micronic to centi-metric crystals, separated by hand-picking on core samples. The development of this sequential extraction procedure for the Callovian-Oxfordian formation shows the importance of the first cobalt hexamine trichloride step to extract the exchangeable strontium adsorbed on clay minerals and block the exchangeable sites with cobalt for the following steps, allowing a good separation of exchangeable fraction and carbonates. However the reagent/solid ratio of 20 seems to be less adapted to carbonate-rich samples. The good separation between exchangeable

  7. Fast high-temperature consolidation of Oxide-Dispersion Strengthened (ODS) steels: process, microstructure, precipitation, properties

    International Nuclear Information System (INIS)

    Boulnat, Xavier

    2014-01-01

    This work aims to lighten the understanding of the behavior of a class of metallic materials called Oxide-Dispersion Strengthened (ODS) ferritic steels. ODS steels are produced by powder metallurgy with various steps including atomization, mechanical alloying and high-temperature consolidation. The consolidation involves the formation of nanoparticles in the steel and various evolutions of the microstructure of the material that are not fully understood. In this thesis, a novel consolidation technique assisted by electric field called 'Spark Plasma Sintering' (SPS) or 'Field-Assisted Sintering Technique' (FAST) was assessed. Excellent mechanical properties were obtained by SPS, comparable to those of conventional hot isostatic pressed (HIP) materials but with much shorter processing time. Also, a broad range of microstructures and thus of tensile strength and ductility were obtained by performing SPS on either milled or atomized powder at different temperatures. However, SPS consolidation failed to avoid heterogeneous microstructure composed of ultrafine-grained regions surrounded by micron grains despite of the rapid consolidation kinetics. A multi-scale characterization allowed to understand and model the evolution of this complex microstructure. An analytical evaluation of the contributing mechanisms can explain the appearance of the complex grain structure and its thermal stability during further heat treatments. Inhomogeneous distribution of plastic deformation in the powder is argued to be the major cause of heterogeneous recrystallization and further grain growth during hot consolidation. Even if increasing the solute content of yttrium, titanium and oxygen does not impede abnormal growth, it permits to control the fraction and the size of the retained ultrafine grains, which is a key-factor to tailor the mechanical properties. Since precipitation through grain boundary pinning plays a significant role on grain growth, a careful

  8. Sleep-Dependent Consolidation of Statistical Learning

    Science.gov (United States)

    Durrant, Simon J.; Taylor, Charlotte; Cairney, Scott; Lewis, Penelope A.

    2011-01-01

    The importance of sleep for memory consolidation has been firmly established over the past decade. Recent work has extended this by suggesting that sleep is also critical for the integration of disparate fragments of information into a unified schema, and for the abstraction of underlying rules. The question of which aspects of sleep play a…

  9. The Demonstration of Short-Term Consolidation.

    Science.gov (United States)

    Jolicoeur, Pierre; Dell'Acqua, Roberto

    1998-01-01

    Results of seven experiments involving 112 college students or staff using a dual-task approach provide evidence that encoding information into short-term memory involves a distinct process termed short-term consolidation (STC). Results suggest that STC has limited capacity and that it requires central processing mechanisms. (SLD)

  10. Containments for consolidated nuclear steam systems

    International Nuclear Information System (INIS)

    Jabsen, F.S.

    1978-01-01

    A containment system for a consolidated nuclear steam system incorporating a nuclear core, steam generator and reactor coolant pumps within a single pressure vessel is described which is designed to provide radiation shielding and pressure suppression. Design details, including those for the dry well and wet well of the containment, are given. (UK)

  11. Budgeting For National Economic Consolidation And Progression ...

    African Journals Online (AJOL)

    The paper exemplifies genuine concern and empathy for the perceived unimpressive pace of growth and development of Nigeria\\'s national economy. The 2007 budget aptly directed at consolidation is crystallized as affording stakeholders the potent drive towards meaningful progression in national economic management ...

  12. Negative Reinforcement Impairs Overnight Memory Consolidation

    Science.gov (United States)

    Stamm, Andrew W.; Nguyen, Nam D.; Seicol, Benjamin J.; Fagan, Abigail; Oh, Angela; Drumm, Michael; Lundt, Maureen; Stickgold, Robert; Wamsley, Erin J.

    2014-01-01

    Post-learning sleep is beneficial for human memory. However, it may be that not all memories benefit equally from sleep. Here, we manipulated a spatial learning task using monetary reward and performance feedback, asking whether enhancing the salience of the task would augment overnight memory consolidation and alter its incorporation into…

  13. Consolidating African Research and Education Networking ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    Consolidating African Research and Education Networking (CORENA) - Phase I. African universities and research institutions possess significant human capacity, but their contribution to national human development as well as their intellectual property output is still very limited. A major cause of this is lack of easy and ...

  14. Tracelink: A model of consolidation and amnesia

    NARCIS (Netherlands)

    Meeter, M.; Murre, J.M.J.

    2005-01-01

    A connectionist model is presented, the TraceLink model, that implements an autonomous "off-line" consolidation process. The model consists of three subsystems: (1) a trace system(neocortex), (2) a link system (hippocampus and adjacent regions), and (3) a modulatory system (basal forebrain and other

  15. Uganda's 2006 multiparty elections: consolidating democracy and ...

    African Journals Online (AJOL)

    However, in conditions where such elections are shrouded in constitutional manipulation, political opaqueness, greed and consolidation of personal rule, they may instead, entrench an authoritarian regime. This article looks at the effects of the recent multiparty elections on the process of democratization and peace building ...

  16. Consolidated Afloat Networks and Enterprise Services (CANES)

    Science.gov (United States)

    2016-03-01

    Information Assurance IATO - Interim Authority to Operate ICD - Initial Capability Document IEA - Information Enterprise Architecture IOC - Initial...2016 Major Automated Information System Annual Report Consolidated Afloat Networks and Enterprise Services (CANES) Defense Acquisition Management...Executive DoD - Department of Defense DoDAF - DoD Architecture Framework FD - Full Deployment FDD - Full Deployment Decision FY - Fiscal Year IA

  17. Malawi's Traditional Leadership and Democracy Consolidation ...

    African Journals Online (AJOL)

    is that the tendency to brand traditional leadership as undemocratic masks debate on its great potential for the promotion of democracy. The article contends that efforts towards democracy consolidation require foregoing harmonious power relations and linkages between traditional leaders and elected local governments; ...

  18. Resting state EEG correlates of memory consolidation.

    Science.gov (United States)

    Brokaw, Kate; Tishler, Ward; Manceor, Stephanie; Hamilton, Kelly; Gaulden, Andrew; Parr, Elaine; Wamsley, Erin J

    2016-04-01

    Numerous studies demonstrate that post-training sleep benefits human memory. At the same time, emerging data suggest that other resting states may similarly facilitate consolidation. In order to identify the conditions under which non-sleep resting states benefit memory, we conducted an EEG (electroencephalographic) study of verbal memory retention across 15min of eyes-closed rest. Participants (n=26) listened to a short story and then either rested with their eyes closed, or else completed a distractor task for 15min. A delayed recall test was administered immediately following the rest period. We found, first, that quiet rest enhanced memory for the short story. Improved memory was associated with a particular EEG signature of increased slow oscillatory activity (rest can facilitate memory, and that this may occur via an active process of consolidation supported by slow oscillatory EEG activity and characterized by decreased attention to the external environment. Slow oscillatory EEG rhythms are proposed to facilitate memory consolidation during sleep by promoting hippocampal-cortical communication. Our findings suggest that EEG slow oscillations could play a significant role in memory consolidation during other resting states as well. Copyright © 2016 Elsevier Inc. All rights reserved.

  19. Evaluation of clayey masses compositions starting from the residue incorporation of the red ceramic industry to obtain tubular ceramic membranes; Avaliacao das composicoes de massas argilosas a partir da incorporacao de residuo da industria de ceramica vermelha na obtencao de membranas ceramicas tubulares

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Adriano Lima da; Chaves, Alexsandra Cristina; Luna, Carlos Bruno Barreto; Neves, Gelmires de Araujo; Lira, Helio de Lucena, E-mail: adrianolimadasilva@hotmail.com, E-mail: alexsandra.chaves@ifap.edu.br, E-mail: brunobarretodemaufcg@hotmail.com, E-mail: gelmires@ufcg.edu.br, E-mail: helio@ufcg.edu.br [Universidade Federal de Campina Grande (UAEMa/CCT/UFCG), PB (Brazil). Unidade Academica de Engenharia de Materiais

    2017-01-15

    The inappropriate residue disposal of red ceramic industry is very high. Nowadays, one of the major challenges is the investigation of processes to obtain alternative materials, enabling the use of these residues to manufacture new materials. This work's objective is to study clayey masses' compositions starting from the residue incorporation of the red ceramic industry to be used in tubular ceramic membranes. Two compositions of ceramic masses were established, composition A (50% of residue) and composition B (70% of residue). Granulometric analysis of the ceramic masses presented an average size of particles, what indicates membranes in the microfiltration scale. Another observed factor is related to the increase of residue amount, what favored a decrease in the ceramic mass' plasticity. A rise in the apparent porosity was also observed, probably because of a possible growing in the bigger pores numbers, due to the sintering high temperature and the elevation of residue quantity itself. (author)

  20. Sleep enhances memory consolidation in children.

    Science.gov (United States)

    Ashworth, Anna; Hill, Catherine M; Karmiloff-Smith, Annette; Dimitriou, Dagmara

    2014-06-01

    Sleep is an active state that plays an important role in the consolidation of memory. It has been found to enhance explicit memories in both adults and children. However, in contrast to adults, children do not always show a sleep-related improvement in implicit learning. The majority of research on sleep-dependent memory consolidation focuses on adults; hence, the current study examined sleep-related effects on two tasks in children. Thirty-three typically developing children aged 6-12 years took part in the study. Actigraphy was used to monitor sleep. Sleep-dependent memory consolidation was assessed using a novel non-word learning task and the Tower of Hanoi cognitive puzzle, which involves discovering an underlying rule to aid completion. Children were trained on the two tasks and retested following approximately equal retention intervals of both wake and sleep. After sleep, children showed significant improvements in performance of 14% on the non-word learning task and 25% on the Tower of Hanoi task, but no significant change in score following the wake retention interval. Improved performance on the Tower of Hanoi may have been due to children consolidating explicit aspects of the task, for example rule-learning or memory of previous sequences; thus, we propose that sleep is necessary for consolidation of explicit memory in children. Sleep quality and duration were not related to children's task performance. If such experimental sleep-related learning enhancement is generalizable to everyday life, then it is clear that sleep plays a vital role in children's educational attainment. © 2013 European Sleep Research Society.

  1. Nicotine facilitates memory consolidation in perceptual learning.

    Science.gov (United States)

    Beer, Anton L; Vartak, Devavrat; Greenlee, Mark W

    2013-01-01

    Perceptual learning is a special type of non-declarative learning that involves experience-dependent plasticity in sensory cortices. The cholinergic system is known to modulate declarative learning. In particular, reduced levels or efficacy of the neurotransmitter acetylcholine were found to facilitate declarative memory consolidation. However, little is known about the role of the cholinergic system in memory consolidation of non-declarative learning. Here we compared two groups of non-smoking men who learned a visual texture discrimination task (TDT). One group received chewing tobacco containing nicotine for 1 h directly following the TDT training. The other group received a similar tasting control substance without nicotine. Electroencephalographic recordings during substance consumption showed reduced alpha activity and P300 latencies in the nicotine group compared to the control group. When re-tested on the TDT the following day, both groups responded more accurately and more rapidly than during training. These improvements were specific to the retinal location and orientation of the texture elements of the TDT suggesting that learning involved early visual cortex. A group comparison showed that learning effects were more pronounced in the nicotine group than in the control group. These findings suggest that oral consumption of nicotine enhances the efficacy of nicotinic acetylcholine receptors. Our findings further suggest that enhanced efficacy of the cholinergic system facilitates memory consolidation in perceptual learning (and possibly other types of non-declarative learning). In that regard acetylcholine seems to affect consolidation processes in perceptual learning in a different manner than in declarative learning. Alternatively, our findings might reflect dose-dependent cholinergic modulation of memory consolidation. This article is part of a Special Issue entitled 'Cognitive Enhancers'. Copyright © 2012 Elsevier Ltd. All rights reserved.

  2. Materials

    CSIR Research Space (South Africa)

    Van Wyk, Llewellyn V

    2009-02-01

    Full Text Available . It is generally included as part of a structurally insulated panel (SIP) where the foam is sandwiched between external skins of steel, wood or cement. Cement composites Cement bonded composites are an important class of building materials. These products... for their stone buildings, including the Egyptians, Aztecs and Inca’s. As stone is a very dense material it requires intensive heating to become warm. Rocks were generally stacked dry but mud, and later cement, can be used as a mortar to hold the rocks...

  3. A COHERENT MATRIX MODEL FOR THE CONSOLIDATION AND COMPACTION OF AN EXCIPIENT WITH MAGNESIUM STEARATE

    NARCIS (Netherlands)

    RIEPMA, KA; VROMANS, H; LERK, CF

    1993-01-01

    This paper reports that magnesium stearate sensitivity of brittle materials is not directly related to the degree of fragmentation during compression. A coherent matrix of magnesium stearate, created by the process of dry blending, is highly sustained during consolidation and compaction of the

  4. Preliminary studies of consolidation of wall paintings: synthesis and characterisation of nanolime

    Directory of Open Access Journals (Sweden)

    Penka I. Girginova

    2016-01-01

    Full Text Available In this publication, we report the synthesis and characterization of calcium and magnesium hydroxides nanoparticles for consolidation of mural paintings. Some preliminary results are discussed. This research is the initial part of our ongoing project which aims to develop new synthetic strategies towards novel and innovative materials for preservation and restoration of old renders.

  5. 7 CFR 15.86 - Consolidated or joint hearings.

    Science.gov (United States)

    2010-01-01

    ... responsibility within the Department for the administration of all the laws extending the Federal financial... agreement order consolidation for hearing. The Secretary may order proceedings in the Department... such consolidation. Hearing Officer ...

  6. Evolution of iron crust and clayey Ferralsol in deeply weathered sandstones of Marília Formation (Western Minas Gerais State, Brazil)

    Science.gov (United States)

    Rosolen, Vania; Bueno, Guilherme Taitson; Melfi, Adolpho José; Montes, Célia Regina; de Sousa Coelho, Carla Vanessa; Ishida, Débora Ayumi; Govone, José Silvio

    2017-11-01

    Extensive flat plateaus are typical landforms in the cratonic compartment of tropical regions. Paleoclimate, pediplanation, laterization, and dissection have created complex and distinct geological, geomorphological, and pedological features in these landscapes. In the Brazilian territory, the flat plateau sculpted in sandstone of Marília Formation (Neocretaceous) belonging to the Sul-Americana surface presents a very clayey and pisolitic Ferralsol (Red and Yellow Latossolo in the Brazilian soil classification). The clayey texture of soil and the pisolites have been considered as weathering products of a Cenozoic detritical formation which is believed to overlay the Marília Formation sandstones. Using data of petrography (optical microscopy and SEM), mineralogy (RXD), and macroscopic structures (description in the field of the arrangement of horizons and layers), a complete profile of Ferralsol with ferricrete and pisolites was studied. The complex succession of facies is in conformity with a sedimentary structure of Serra da Galga member (uppermost member of Marília Formation). The hardening hematite concentration appears as layered accretions in the subparallel clayey lenses of sandstone saprolite, preserving its structure. Iron contents varied according to different soil fabrics. Higher concentrations of iron are found in the massive ferricrete or in pisolites in the mottled horizon. Kaolinite is a dominant clay mineral and shows two micro-organizations: (1) massive fabric intrinsic to the sedimentary rock, and (2) reworked in pisolites and illuviated features. The pisolites are relicts of ferricrete in the soft bioturbated topsoil. The continuous sequence of ferricrete from saprolite to the Ferralsol indicates that the regolith is autochthonous, developed directly from sandstones of Marília Formation, through a long and intense process of laterization.

  7. Consolidation of long-term memory: Evidence and alternatives.

    OpenAIRE

    Meeter, M.; Murre, J.M.J.

    2004-01-01

    Memory loss in retrograde amnesia has long been held to be larger for recent periods than for remote periods, a pattern usually referred to as the Ribot gradient. One explanation for this gradient is consolidation of long-term memories. Several computational models of such a process have shown how consolidation can explain characteristics of amnesia, but they have not elucidated how consolidation must be envisaged. Here findings are reviewed that shed light on how consolidation may be impleme...

  8. Operation and consolidation: lifetime of equipment and priorities TS

    CERN Document Server

    Béjar-Alonso, Isabel

    2008-01-01

    Since 1999 the TS department has benchmarked his services with the industry and other research laboratories and has prepared several consolidation plans. An evaluation of the results obtained from the different consolidation plans will be summarized. The difference between the projects achieved and those planned will be analyzed. The impact of the differed consolidation and of the maintenance backlog will be analyzed in order to present the future TS consolidation strategy

  9. Using Fast Hot Shock Wave Consolidation Technology to Produce Superconducting MgB2

    Directory of Open Access Journals (Sweden)

    T. Gegechkori

    2018-02-01

    Full Text Available The original hot shock wave assisted consolidation method combining high temperature was applied with the two-stage explosive process without any further sintering to produce superconducting materials with high density and integrity. The consolidation of MgB2 billets was performed at temperatures above the Mg melting point and up to 1000oC in partially liquid condition of Mg-2B blend powders. The influence of the type of boron (B isotope in the composition on critical temperature and superconductive properties was evaluated. An example of a hybrid Cu-MgB2–Cu superconducting tube is demonstrated and conclusions are discussed.

  10. Long-term observations programme on the geological environment of a radioactive waste repository in clayey or related formations, implications on the various phases of the project

    International Nuclear Information System (INIS)

    Manfroy, P.; Raynal, M.; Bonne, A.

    1993-01-01

    The process of emplacing radioactive waste in deep clayey or related formations involves numerous interdependent actions, the common objective of which is to guarantee optimum isolation of the waste for the durations required. Among these actions, observations on the geological environment will have to extend over a very long period of time, from site characterization to repository closure. All the far-field and near-field observations will constitute the basis and confirmation of the models intended to describe the phenomena which take place in the repository and its surrounding host formation and will have to be taken into account in the repository closure procedures. 6 refs

  11. Inventory of clayey and marly formations in France and update of knowledge on the Albian in Aube. Final report. Volume 1: Report. Volume 2: Appendices

    International Nuclear Information System (INIS)

    2008-01-01

    In the context of searching a site for a storage centre for low level and long life radioactive wastes, this voluminous document reports geological studies on soils presenting the most favourable geological and hydro-geological criteria to retain radionuclides. The locations, characteristics, variability, geology, hydro-geology, and environmental constraints of various and precisely identified clayey or marly formations of the Paris basin and of the Aquitaine basin are analysed and reported in detail. Some additional results of investigations of the Albian site in the Aube district are also reported. The appendices contain information, data and analysis concerning the different French regions

  12. Determination of diffusion and adsorption coefficients for some contaminants in clayey soil and rock: Laboratory determination and field evaluation

    Energy Technology Data Exchange (ETDEWEB)

    Barone, F S

    1990-01-01

    A laboratory diffusion test determination of diffusion coefficient (D) and adsorption coefficient (K{sub d}) for various inorganic and organic species in a saturated, undisturbed, clayey soil is presented. Diffusion tests conducted for inorganic species (Cl{sup {minus}} , Na{sup +}, K{sup +}, Mg{sup 2+}, and Ca{sup 2+}), involved placing domestic landfill leachate on top of a layer of clay and allowing the chemical constituents to diffuse into the soil. The mathematical model POLLUTE was then used to back-figure (D) and (K{sub d}) for each species. Diffusion tests conducted for organic species (acetone, 1,4-dioxane, aniline, chloroform, and toluene), involved diffusion of the species from a source solution placed on one side of a clay plug, into a distilled water collector solution on the opposite side. Using POLLUTE, D and K{sub d} were then determined by fitting the measured concentration variation with time in both the source and collector solution. In addition to the laboratory study, an investigation of inorganic contaminant diffusion below an existing industrial landfill site was conducted by analyzing soil and pore water specimens from the clay layer underlying the waste. Concentration profiles for Cl{sup {minus}}, So{sub 4}{sup 2{minus}}, Na+, Ca{sup 2+} and Mg{sup 2+}, showed above background levels to a depth of 1.4 m below the waste after 11 years of migration. K{sup +}, B, and NH{sub 3}-N profiles, penetrated to less than 0.5 m below the waste. Field profiles for Na{sup +}, K{sup +}, Cl{sup {minus}}, and SO{sub 4}{sup 2{minus}} were then compared with those predicted using POLLUTE with D and K{sub d} values obtained from diffusion tests using leachate and natural uncontaminated clay from the site. Finally, a laboratory diffusion test determination of Cl{sup {minus}} diffusion coefficient in samples of intact, saturated shale and mudstone is presented.

  13. Long-term monitoring of nitrate-N transport to drainage from three agricultural clayey till fields

    Science.gov (United States)

    Ernstsen, V.; Olsen, P.; Rosenbom, A. E.

    2015-01-01

    The application of nitrogen (N) fertilisers to crops grown on tile-drained fields is necessary to sustain most modern crop production, but poses a risk to the aquatic environment since tile drains facilitate rapid transport pathways with no significant reduction in nitrate. To maintain the water quality of the aquatic environment and the provision of food from highly efficient agriculture in line with the EU's Water Framework Directive and Nitrates Directive, field-scale knowledge is imperative if there is to be differentiated N-regulation in future. This study describes nitrate-N leaching to drainage based on coherent monitoring of nitrate-N concentrations, the climate, the groundwater table and crop-specific parameters obtained over eleven years (2001-2011) at three subsurface-drained clayey till fields (1.3-2.3 ha). The monitoring results showed significant field differences in nitrate-N transport to drainage. Not only were these caused by periods of bare soil after short-season crops and N-fixing crops (pea), which have been shown to generate high nitrate-N concentrations in drainage, but by the hydrogeological field conditions that were shown to be the controlling factor of nitrate-N transport to drainage. The fields had the following characteristics: (A) the lowest mass transport (13 kg N ha-1) and fertiliser input had short-term and low-intensity drainage with the highest nitrate-N concentrations detected, representing 40% of net precipitation (226 mm) combined with low air temperatures, (B) the medium mass transport (14 kg N ha-1) had medium-term and medium-intensity drainage, representing 42% of net precipitation (471 mm) combined with periods of both low and higher air temperatures, (C) the highest mass transport (19 kg N ha-1) had long-term drainage, representing 68% of net precipitation (617 mm), but had the highest potential for in-situ soil denitrification and post-treatment (e.g. constructed wetlands) due to long periods with both high water

  14. 10 CFR 1040.123 - Consolidated or joint hearings.

    Science.gov (United States)

    2010-01-01

    ... ACTIVITIES Enforcement Opportunity for Hearing § 1040.123 Consolidated or joint hearings. In cases in which... 10 Energy 4 2010-01-01 2010-01-01 false Consolidated or joint hearings. 1040.123 Section 1040.123... departments or agencies, where applicable, provide for the conduct of consolidated or joint hearings and for...

  15. 10 CFR 4.64 - Consolidated or joint hearings.

    Science.gov (United States)

    2010-01-01

    ... Consolidated or joint hearings. In cases in which the same or related facts are asserted to constitute... 10 Energy 1 2010-01-01 2010-01-01 false Consolidated or joint hearings. 4.64 Section 4.64 Energy... or agencies, where applicable, provide for the conduct of consolidated or joint hearings, and for the...

  16. 29 CFR 4011.6 - Mergers, consolidations, and spinoffs.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 9 2010-07-01 2010-07-01 false Mergers, consolidations, and spinoffs. 4011.6 Section 4011... REPORTING AND DISCLOSURE REQUIREMENTS DISCLOSURE TO PARTICIPANTS § 4011.6 Mergers, consolidations, and spinoffs. In the case of a plan involved in a merger, consolidation, or spinoff transaction that becomes...

  17. 77 FR 17091 - Trust Land Consolidation Draft Plan

    Science.gov (United States)

    2012-03-23

    ... DEPARTMENT OF THE INTERIOR Office of the Secretary Trust Land Consolidation Draft Plan AGENCY... reopening the period for commenting on the Cobell Land Consolidation Program Draft Plan (also known as the Trust Land Consolidation Draft Plan), which is the draft plan for accomplishing these goals. DATES...

  18. 7 CFR 1710.108 - Mergers and consolidations.

    Science.gov (United States)

    2010-01-01

    ... operating efficiency and financial soundness. (b) After a merger or consolidation, RUS will give priority... 7 Agriculture 11 2010-01-01 2010-01-01 false Mergers and consolidations. 1710.108 Section 1710.108... and Basic Policies § 1710.108 Mergers and consolidations. (a) RUS encourages its borrowers to consider...

  19. 24 CFR 401.401 - Consolidated Restructuring Plans.

    Science.gov (United States)

    2010-04-01

    ... PROGRAM (MARK-TO-MARKET) Restructuring Plan § 401.401 Consolidated Restructuring Plans. A PAE may request HUD to approve a Consolidated Restructuring Plan that presents an overall strategy for more than one... resources, HUD will not approve any Consolidated Restructuring Plans that have a detrimental effect on...

  20. 26 CFR 1.1502-4 - Consolidated foreign tax credit.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 12 2010-04-01 2010-04-01 false Consolidated foreign tax credit. 1.1502-4... TAX (CONTINUED) INCOME TAXES Consolidated Tax Liability § 1.1502-4 Consolidated foreign tax credit. (a) In general. The credit under section 901 for taxes paid or accrued to any foreign country or...

  1. Low-Cost Structural Thermoelectric Materials: Processing and Consolidation

    Science.gov (United States)

    2015-01-01

    milling media (440C stainless steel balls) with a ball-to-powder ratio of 10-to-1 by weight, and then sealed inside a glove box in an argon (Ar...elements with superior mechanical, tribological , and/or oxidation/corrosion properties (e.g., transition metals) but are less efficient at converting heat...the appropriate proportions, for alloys) and grinding media (typically steel balls) in the right proportion into a vial. This is then loaded into a

  2. Consolidation of materials by pulse-discharge processes

    Science.gov (United States)

    Strizhakov, E. L.; Nescoromniy, S. V.

    2017-07-01

    The article presents the research and the analysis of the pulse-discharge processes of capacitor discharge sintering: CD Stud Welding, capacitor discharge percussion welding (CDPW), high-voltage capacitor welding with an inductive-dynamic drive (HVCW with IDD), pulse electric current sintering (PECS) of powders. The comparative analysis of the impact parameter is presented.

  3. Money Enhances Memory Consolidation--But Only for Boring Material

    Science.gov (United States)

    Murayama, Kou; Kuhbandner, Christof

    2011-01-01

    Money's ability to enhance memory has received increased attention in recent research. However, previous studies have not directly addressed the time-dependent nature of monetary effects on memory, which are suggested to exist by research in cognitive neuroscience, and the possible detrimental effects of monetary rewards on learning interesting…

  4. Sleep and memory consolidation: motor performance and proactive interference effects in sequence learning.

    Science.gov (United States)

    Borragán, Guillermo; Urbain, Charline; Schmitz, Rémy; Mary, Alison; Peigneux, Philippe

    2015-04-01

    That post-training sleep supports the consolidation of sequential motor skills remains debated. Performance improvement and sensitivity to proactive interference are both putative measures of long-term memory consolidation. We tested sleep-dependent memory consolidation for visuo-motor sequence learning using a proactive interference paradigm. Thirty-three young adults were trained on sequence A on Day 1, then had Regular Sleep (RS) or were Sleep Deprived (SD) on the night after learning. After two recovery nights, they were tested on the same sequence A, then had to learn a novel, potentially competing sequence B. We hypothesized that proactive interference effects on sequence B due to the prior learning of sequence A would be higher in the RS condition, considering that proactive interference is an indirect marker of the robustness of sequence A, which should be better consolidated over post-training sleep. Results highlighted sleep-dependent improvement for sequence A, with faster RTs overnight for RS participants only. Moreover, the beneficial impact of sleep was specific to the consolidation of motor but not sequential skills. Proactive interference effects on learning a new material at Day 4 were similar between RS and SD participants. These results suggest that post-training sleep contributes to optimizing motor but not sequential components of performance in visuo-motor sequence learning. Copyright © 2015 Elsevier Inc. All rights reserved.

  5. The Impact of Approved Accounting Standard AASB 1024 “Consolidated Accounts” on the Information Included in Consolidated Financial Statements

    OpenAIRE

    Pramuka, Bambang Agus

    1995-01-01

    The intent of consolidated financial statements is to provide meaningful, relevant, useful, and reliable information about the operations of a group of companies. In compliance with AASB 1024 'Consolidated Accounts', and AAS 24 Consolidated Financial Reports', a parent entity now has to include in its consolidated financial statements all controlled entities, regardless of their legal form or the ownership interest held. The new Standard also pr...

  6. Modelling coupled sedimentation and consolidation of fine slurries

    Energy Technology Data Exchange (ETDEWEB)

    Masala, S. [Klohn Crippen Berger, Calgary, AB (Canada)

    2010-07-01

    This article presented a model to simulate and successfully predict the essential elements of sedimentation and consolidation as a coupled process, bringing together separately developed models from chemistry and geology/geotechnical engineering, respectively. The derived model is for a 1-dimensional simultaneous sedimentation and consolidation of a solid-liquid suspension that uses permeability as the unifying concept for the hydrodynamic interaction between solid and liquid in a suspension. The numerical solution relies on an explicit finite difference procedure in material coordinates, and an Euler forward-marching scheme was used for advancing the solution in time. The problem of internal discontinuities was solved by way of convenient numerical solutions and Lagrangian coordinates. Java-based SECO software with a user-friendly graphical user interface (GUI) was used to implement the model, allowing the solution process to be visualized and animated. The software functionality along with GUI and programming issues were discussed at length. A fine-grained suspension data set was used to validate the model. 10 refs., 12 figs.

  7. Acoustic slow waves and the consolidation transition

    International Nuclear Information System (INIS)

    Johnson, D.L.; Plona, T.J.

    1982-01-01

    We have investigated the ultrasonic properties of unconsolidated (loose) glass beads and of lightly fused (consolidated) glass beads when the pore space is saturated with water. At a frequency of 500 kHz we have observed a single compressional wave in the former whose speed is 1.79 km/s and two distinct compressional waves with speeds 2.81 km/s and 0.96 km/s in the latter. The Biot theory is shown to give an accurate description of this phenomenon. We also analyze the acoustics of low temperature He ii in packed powder superleaks; either the fast wave for unconsolidated systems or the slow wave in a highly consolidated (fused) frame may be considered to be the 4th sound mode. In all such systems, the acoustic properties can be very simply understood by considering the velocities of propagation as continuous functions of the elastic moduli of the solid skeletal frames

  8. Transvaal Consolidated Land and Exploration Company, Limited

    International Nuclear Information System (INIS)

    Lawrence, R.S.

    1983-01-01

    The difficult economic circumstances with which almost the whole world had to contend, brought serious financial crisis in many countries. South Africa also had its own share of serious problems. Despite this situation, Transvaal Consolidated Land and Exploration Company, Limited, showed on increase in earnings of 24 per cent per share. The reason for this lies mainly in two areas. Firstly the company acquired the mining related business of Rand Mines, Limited. Included in the acquisition was a partfolio of shares mainly in the company's associated gold and uranium mining companies and additional shares in its listed coal mining subsidiaries. Secondly, the average gold price realised by producers in rand terms, was considerably higher than in the previous year. Consolidated profit attributable to members increased by 52 per cent to R82,6 million

  9. Acute exercise and motor memory consolidation

    DEFF Research Database (Denmark)

    Thomas, Richard; Korsgaard Johnsen, Line; Geertsen, Svend Sparre

    2016-01-01

    where low to moderate intensities may be more suitable. The aim of this study was to investigate the role of intensity in mediating the effects of acute cardiovascular exercise on motor skill learning. We investigated the effects of different exercise intensities on the retention (performance score...... an important role in modulating the effects that a single bout of cardiovascular exercise has on the consolidation phase following motor skill learning. There appears to be a dose-response relationship in favour of higher intensity exercise in order to augment off-line effects and strengthen procedural memory.......A single bout of high intensity aerobic exercise (~90% VO2peak) was previously demonstrated to amplify off-line gains in skill level during the consolidation phase of procedural memory. High intensity exercise is not always a viable option for many patient groups or in a rehabilitation setting...

  10. Consolidated financial statements for fiscal year 1996

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-02-01

    The following overview and accompanying audited financial statements have been prepared for Fiscal Year (FY) 1996 to report the financial position and the results of operations of the Department of Energy. These statements include the consolidated Statement of Financial Position and the consolidated Statement of Operations and Changes in Net Position. The statements have been prepared in accordance with the Office of Management and Budget Bulletin No. 94-01, Form and Content for Agency Financial Statements, and were developed in accordance with the hierarchy of accounting standards described therein. The overview provides a narrative on the Department of Energy`s mission, activities, and accomplishments. Utilizing performance measures as the primary vehicle for communicating Departmental accomplishments and results, this overview discusses the most significant measures while others are discussed in the supplemental information to the financial statements.

  11. Risk Analysis for the Different Consolidation Proposals

    CERN Document Server

    Strait, J

    2009-01-01

    In parallel with the repairs in sector 34, improvements are planned to a number of systems, to allow safe detection of faults similar to the one which caused the incident of 19 September, and to limit the damage should a similar incident nonetheless occur. These include improved bus and quench detection systems, improved pressure relief for the insulating and beam vacuum systems, and improved anchoring of the SSS to the tunnel floor. Not all of the planned mitigations, however, may be fully implemented before the restart of the LHC in 2009. I will review the potential benefits of partial or complete implementation of each of the planned improvements, individually or together with others, and conversely the potential risks (consequences) of delayed implementation. I will also review the risks that remain even after the planned consolidation is complete. Considering all proposals and the different risks, I will comment on what would be the best strategy for consolidation, and on the strategy for operations unde...

  12. Local Identity in Times of Jurisdictional Consolidation

    DEFF Research Database (Denmark)

    Hansen, Sune Welling; Kjær, Ulrik

    of a dataset which consists of large scale citizen surveys conducted in 2001, 2009 and 2013, combined with register data on the Danish municipalities (the two surveys in 2001 and 2009 even have a panel structure). Our paper contributes to the existing literature on local identity by examining the influence......Reforming the public sector has become increasingly popular. Some of the reforms have been jurisdictional consolidations of subnational authorities such as regions and municipalities. One question which remains unanswered is whether such consolidations affect citizens’ local identity? We take...... a first step towards providing an answer by examining whether citizens’ affective attachment to their municipality – and other administrative and geographical areas – declined or flourished in connection with a large-scale municipal reform implemented in Denmark in 2007. Empirically, we make use...

  13. Relation Between Filtration and Soil Consolidation Theories

    Directory of Open Access Journals (Sweden)

    Strzelecki Tomasz

    2015-03-01

    Full Text Available This paper presents a different, than commonly used, form of equations describing the filtration of a viscous compressible fluid through a porous medium in isothermal conditions. This mathematical model is compared with the liquid flow equations used in the theory of consolidation. It is shown that the current commonly used filtration model representation significantly differs from the filtration process representation in Biot’s and Terzaghi’s soil consolidation models, which has a bearing on the use of the methods of determining the filtration coefficient on the basis of oedometer test results. The present analysis of the filtration theory equations should help interpret effective parameters of the non-steady filtration model. Moreover, equations for the flow of a gas through a porous medium and an interpretation of the filtration model effective parameters in this case are presented.

  14. Prototypical Consolidation Demonstration Project: Final report

    International Nuclear Information System (INIS)

    Gili, J.A.; Poston, V.K.

    1993-11-01

    This is the final report of the Prototypical Consolidation Demonstration Project, which was funded by the US Department of Energy's Office of Civilian Radioactive Waste Management. The project had two objectives: (a) to develop and demonstrate a prototype of production-scale equipment for the dry, horizontal consolidation and packaging of spent nuclear fuel rods from commercial boiling water reactor and pressurized water reactor fuel assemblies, and (b) to report the development and demonstration results to the US Department of Energy, Idaho Operations Office. This report summarizes the activities and conclusions of the project management contractor, EG ampersand G Idaho, Inc., and the fabrication and testing contractor, NUS Corporation (NUS). The report also presents EG ampersand G Idaho's assessments of the equipment and procedures developed by NUS

  15. The Synthesis of Nanostructured WC-Based Hardmetals Using Mechanical Alloying and Their Direct Consolidation

    Directory of Open Access Journals (Sweden)

    N. Al-Aqeeli

    2014-01-01

    Full Text Available Tungsten carbide- (WC- based hardmetals or cemented carbides represent an important class of materials used in a wide range of industrial applications which primarily include cutting/drilling tools and wear resistant components. The introduction and processing of nanostructured WC-based cemented carbides and their subsequent consolidation to produce dense components have been the subject of several investigations. One of the attractive means of producing this class of materials is by mechanical alloying technique. However, one of the challenging issues in obtaining the right end-product is the possible loss of the nanocrystallite sizes due to the undesirable grain growth during powder sintering step. Many research groups have engaged in multiple projects aiming at exploring the right path of consolidating the nanostructured WC-based powders without substantially loosing the attained nanostructure. The present paper highlights some key issues related to powder synthesis and sintering of WC-based nanostructured materials using mechanical alloying. The path of directly consolidating the powders using nonconventional consolidation techniques will be addressed and some light will be shed on the advantageous use of such techniques. Cobalt-bonded hardmetals will be principally covered in this work along with an additional exposure of the use of other binders in the WC-based hardmetals.

  16. WWER reactor pressure vessel embrittlement knowledge - a way forward for consolidation

    International Nuclear Information System (INIS)

    Von Estorff, U.; Brumovsky, M.

    2010-01-01

    Many stakeholders, such as Institutes, R and D Organisations, Regulators, Utilities, Governmental Organisations, have recognised the need for collecting, preserving, consolidating (validating), and disseminating nuclear knowledge (documents, competences and data), in order to make it easily accessible to future generations through modern informatics tools and training and education measures. A broad spectrum of components and technologies should be considered, i.e. reactor pressure vessel (RPV), piping, internals, steam generator, etc. regarding knowledge, material data and practices. In the long run, it will also support future decommissioning exercises of nuclear installations as a valuable knowledge source. In addition to the knowledge in each Member State, the IE produced a long standing record of results from its own institutional activities and even more through the participation to a large number of European Network partnership projects. It is important, besides preservation, to consolidate the enormous amount of scientific results produced since. Therefore, the IE has developed a method for consolidation of nuclear knowledge. The method relays on the mobilisation of all identified leading experts in the EU in re-evaluating old knowledge and consolidating what is necessary to create training materials for the new generations. This method was applied for a pilot study for consolidating and preserving WWER RPV safety related knowledge, which is scattered in many countries and in different languages, facing a serious issue in terms of getting lost. This initiative could be the start of a wider Nuclear Knowledge Preservation and Consolidation activity. Experience gained and lessons learnt from the first exercise will be presented in this paper. (authors)

  17. EDF - 2005 Consolidated Annual Results - Analysts' Presentation. Consolidated financial statements at December 31, 2005

    International Nuclear Information System (INIS)

    2006-01-01

    As the world's biggest electricity generator, the EDF Group covers every sector of expertise, from generation to trading and transmission grids. EDF builds on the expertise of its people, its R and D and engineering skills, its experience as a leading industry operator and the attentive support of its customers to deliver competitive solutions that successfully reconcile economic growth with climate protection. This document presents the 2005 annual results and Consolidated financial statements of the Group at 31 December 2005: Consolidated income statements, consolidated balance sheets, consolidated cash flow statements, variation in consolidated equity, notes (group accounting policies, impact of first-time application of IFRs, transition to standards IAS 32 and 39 concerning financial instruments, summary of accounting and valuation methods, public distribution concessions in France, significant events and transactions of 2005, impact of the law of august 9, 2004 on comparability, changes in the scope of consolidation, segment reporting, sales, fuel and energy purchases, other external expenses, contractual obligations and commitments entered into in the course of business, personnel expenses, other operating income and expenses, other income and expenses, financial result, income taxes, basic earnings per share and diluted earnings per share, goodwill, other intangible assets, property, plant and equipment, investments in companies accounted for under the equity method, financial assets, inventories, including work-in-process, trade receivables, other receivables, cash and cash equivalents, available-for-sale assets and liabilities, equity, provisions, special concession liabilities, current and non-current financial liabilities, derivatives, other liabilities, related parties, greenhouse gas emission quotas, environment, subsequent events, scope of consolidation

  18. Consolidated results 1999 outlook for 2000

    Energy Technology Data Exchange (ETDEWEB)

    Gadonneix, P. [Gaz de France (GDF), 75 - Paris (France)

    2000-07-01

    This document presents an economic analysis of the consolidated results 1999 for the Group Gaz De France for the year 1999, showing a radical change for the gas industry. The main topics discussed are: a growth market for natural gas, a highly de-compartmentalized market, a market in which the Gaz de France group is an European leader and a market marked in 1999 by a sharp rise in oil prices. (A.L.B.)

  19. Consolidated results 1999 outlook for 2000

    International Nuclear Information System (INIS)

    Gadonneix, P.

    2000-01-01

    This document presents an economic analysis of the consolidated results 1999 for the Group Gaz De France for the year 1999, showing a radical change for the gas industry. The main topics discussed are: a growth market for natural gas, a highly de-compartmentalized market, a market in which the Gaz de France group is an European leader and a market marked in 1999 by a sharp rise in oil prices. (A.L.B.)

  20. Interpretation of Consolidation Test on Søvind Marl

    DEFF Research Database (Denmark)

    Grønbech, Gitte Lyng; Ibsen, Lars Bo; Nielsen, Benjaminn Nordahl

    2012-01-01

    The article deals with the interpretation of consolidation test in order to determine the preconsolidation stress; this is done by reviewing different methods. A main point in the article is the interaction between the consolidation and the secondary consolidation strains, and the methods used...... to separate the two strain types. This is in Denmark traditionally done by a √(t)-log(t) description, where the secondary consolidation first starts when the consolidation process is over. This assumption gives an uncertain description of the strain process, since the two processes in reality run...

  1. Implementation of a consolidated, standardized database of environmental measurements data

    International Nuclear Information System (INIS)

    James, T.L.

    1996-10-01

    This report discusses the benefits of a consolidated and standardized database; reasons for resistance to the consolidation of data; implementing a consolidated database, including attempts at standardization, deciding what to include in the consolidated database, establishing lists of valid values, and addressing quality assurance/quality control (QA/QC) issues; and the evolution of a consolidated database, which includes developing and training a user community, resolving configuration control issues, incorporating historical data, identifying emerging standards, and developing pointers to other data. OREIS is used to illustrate these topics

  2. Local communities’ consolidation process: political factors

    Directory of Open Access Journals (Sweden)

    V. V. Fedorenko

    2017-04-01

    It has been underlined that the local communities’ consolidation process in the contemporary world is the problem which has both empirical and theoretical importance. Depending on the size of the local area, local polices are taking different forms. As usual, they provide an agreement and compromise solutions based on issues that are important to the local community. The experience of the developed democracies has shown that local assemblies ensure the establishment of coalitions based on short-termed procedures. The study has tested that an important aspect of the formation of local communities consolidated position is based on development issues and civil participation. It is especially visible in the United States and the EU countries. The municipality level determines the quality of local political bodies, which is formed on party basis. For contemporary Ukraine important tools for provision of political responsibility are forces, which take care about the local communities and determine their development for a long period. Overall, the consolidation of political forces in the local government system is an important task that determines the need for the adoption of regulatory instruments which would ensure the harmonious and constructive political cooperation regardless of their ideological positions.

  3. Autobiographical thinking interferes with episodic memory consolidation.

    Directory of Open Access Journals (Sweden)

    Michael Craig

    Full Text Available New episodic memories are retained better if learning is followed by a few minutes of wakeful rest than by the encoding of novel external information. Novel encoding is said to interfere with the consolidation of recently acquired episodic memories. Here we report four experiments in which we examined whether autobiographical thinking, i.e. an 'internal' memory activity, also interferes with episodic memory consolidation. Participants were presented with three wordlists consisting of common nouns; one list was followed by wakeful rest, one by novel picture encoding and one by autobiographical retrieval/future imagination, cued by concrete sounds. Both novel encoding and autobiographical retrieval/future imagination lowered wordlist retention significantly. Follow-up experiments demonstrated that the interference by our cued autobiographical retrieval/future imagination delay condition could not be accounted for by the sound cues alone or by executive retrieval processes. Moreover, our results demonstrated evidence of a temporal gradient of interference across experiments. Thus, we propose that rich autobiographical retrieval/future imagination hampers the consolidation of recently acquired episodic memories and that such interference is particularly likely in the presence of external concrete cues.

  4. Detection of cracks with low vertical offset in clayey formations from galleries by using seismic methods. Tournemire experimental station. First part: problem analysis and measurement sizing

    International Nuclear Information System (INIS)

    Bretaudeau, Francois; Gelis, Celine; Cabrera, Justo; Leparoux, Donatienne; Cote, Philippe

    2012-01-01

    Within the frame of the expertise of the ANDRA file on the project of storage of radioactive wastes in clayey formations, the detection of natural cracks which could locally alter the argillite containment properties is a crucial issue. As some previous studies showed that some cracks exhibiting a low vertical offset could not be detected in clayey formations from the surface, this document reports a study which aimed at assessing the possibility of detection of such a crack by means of seismic methods directly implemented from underground works. It reports a detailed analysis of the seismic imagery problem, the characterization of different areas of the investigated environment, the assessment and validation of various hypotheses by using experimental data obtained in an experimental station and numerical simulations. The potential of each envisaged method (migration, tomography, wave form inversion) is assessed, notably with respect to synthetic seismic data obtained by numerical modelling. Preliminary results are used to size a complete seismic measurement campaign aimed at the characterization of the crack area, and at the assessment of detection limitations of the different methods

  5. Commercial development of a new process of uraniferous ore sintering by pelletizing before dump leaching (wet process) application to a very clayey ore of Nord-Aquitaine

    International Nuclear Information System (INIS)

    Videau, G.; Roche, M.

    1990-01-01

    Much of the French uranium ore contains clay of sedimentary origin or derived from the alteration of rocks of the granite type. During a dump leaching operation by a wet process, these clays reduce the percolation rates and sometimes the percolation rates are so low that the very essence of the dump leaching operation can be called in question. This problem arises particularly for the treatment of the ore of Nord-Aquitaine. The results of tests, carried out at the SEPA in Bessines, have shown that after pelletizing clayey ores with sodium silicate in the presence of sulphuric acid for the polymerization of the silicate, the percolation rates were much increased. This new method was successfully applied, from a laboratory column to a pilot dump of 500 tonnes for the very clayey ore of Nord-Aquitaine. This ore of low grade (approx. 1000 ppm of U) seems to be difficult to upgrade by any other method of treatment in the present economic context [fr

  6. An experimental investigation of the consolidation behaviour of uncured prepregs under processing conditions

    OpenAIRE

    Nixon-Pearson, Ollie; Belnoue, Jonathan; Ivanov, Dmitry; Potter, Kevin; Hallett, Stephen

    2017-01-01

    This paper presents a methodology and research study that characterises toughened materials, as is needed for optimisation of composite manufacturing processes. The specific challenge is to cover all of the stages of advanced composite manufacturing: fibre deposition by automatic fibre placement machines, hot or room temperature debulking, and consolidation in an autoclave. In these processes the material experiences a wide range of processing parameters: pressure, load rate, temperatures, an...

  7. Uniaxial creep as a control on mercury intrusion capillary pressure in consolidating rock salt

    Energy Technology Data Exchange (ETDEWEB)

    Dewers, Thomas [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Heath, Jason E. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Leigh, Christi D. [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States)

    2015-09-01

    The nature of geologic disposal of nuclear waste in salt formations requires validated and verified two - phase flow models of transport of brine and gas through intact, damaged, and consolidating crushed salt. Such models exist in oth er realms of subsurface engineering for other lithologic classes (oil and gas, carbon sequestration etc. for clastics and carbonates) but have never been experimentally validated and parameterized for salt repository scenarios or performance assessment. Mo dels for waste release scenarios in salt back - fill require phenomenological expressions for capillary pressure and relative permeability that are expected to change with degree of consolidation, and require experimental measurement to parameterize and vali date. This report describes a preliminary assessment of the influence of consolidation (i.e. volume strain or porosity) on capillary entry pressure in two phase systems using mercury injection capillary pressure (MICP). This is to both determine the potent ial usefulness of the mercury intrusion porosimetry method, but also to enable a better experimental design for these tests. Salt consolidation experiments are performed using novel titanium oedometers, or uniaxial compression cells often used in soil mech anics, using sieved run - of - mine salt from the Waste Isolation Pilot Plant (WIPP) as starting material. Twelve tests are performed with various starting amounts of brine pore saturation, with axial stresses up to 6.2 MPa (%7E900 psi) and temperatures to 90 o C. This corresponds to UFD Work Package 15SN08180211 milestone "FY:15 Transport Properties of Run - of - Mine Salt Backfill - Unconsolidated to Consolidated". Samples exposed to uniaxial compression undergo time - dependent consolidation, or creep, to various deg rees. Creep volume strain - time relations obey simple log - time behavior through the range of porosities (%7E50 to 2% as measured); creep strain rate increases with temperature and applied stress as

  8. Consolidation of long-term memory: evidence and alternatives.

    Science.gov (United States)

    Meeter, Martijn; Murre, Jaap M J

    2004-11-01

    Memory loss in retrograde amnesia has long been held to be larger for recent periods than for remote periods, a pattern usually referred to as the Ribot gradient. One explanation for this gradient is consolidation of long-term memories. Several computational models of such a process have shown how consolidation can explain characteristics of amnesia, but they have not elucidated how consolidation must be envisaged. Here findings are reviewed that shed light on how consolidation may be implemented in the brain. Moreover, consolidation is contrasted with alternative theories of the Ribot gradient. Consolidation theory, multiple trace theory, and semantization can all handle some findings well but not others. Conclusive evidence for or against consolidation thus remains to be found.

  9. Consolidation treatments applied to ceramic tiles: are they homogeneous?

    International Nuclear Information System (INIS)

    Costa, D.; Leal, A.S.; Mimoso, J.M; Pereira, S.M.R.

    2017-01-01

    The mass consolidation treatment of azulejos is necessary when ceramic biscuits show signs of disaggregation. Such treatment is often used as a complementary conservation technique to the reestablishment of weakened glaze-ceramic bonds. In this research, two commonly used consolidants (ethyl silicate and acrylic resin) were tested on artisanal ceramic tiles via mass consolidation and the resulting impregnation profiles were evaluated. The results indicated that after consolidation, hard zones frequently formed due to localized consolidant concentration after the polymerization and curing processes. These inhomogeneous hard zones subsequently influenced the results obtained through conventional mechanical strength testing (i.e. flexural and compression), creating a false impression of success. This research demonstrated that by using the Drilling Resistance Measuring System, impregnation characteristics such as penetration depth and distribution of consolidant could be observed that otherwise could not be discerned through the more common testing methods. As such, a more extensive evaluation of consolidation effects was achieved. [es

  10. Consolidation treatments applied to ceramic tiles: are they homogeneous?

    Directory of Open Access Journals (Sweden)

    D. Costa

    2017-01-01

    Full Text Available The mass consolidation treatment of azulejos is necessary when ceramic biscuits show signs of disaggregation. Such treatment is often used as a complementary conservation technique to the reestablishment of weakened glaze-ceramic bonds. In this research, two commonly used consolidants (ethyl silicate and acrylic resin were tested on artisanal ceramic tiles via mass consolidation and the resulting impregnation profiles were evaluated. The results indicated that after consolidation, hard zones frequently formed due to localized consolidant concentration after the polymerization and curing processes. These inhomogeneous hard zones subsequently influenced the results obtained through conventional mechanical strength testing (i.e. flexural and compression, creating a false impression of success. This research demonstrated that by using the Drilling Resistance Measuring System, impregnation characteristics such as penetration depth and distribution of consolidant could be observed that otherwise could not be discerned through the more common testing methods. As such, a more extensive evaluation of consolidation effects was achieved.

  11. Consolidated Reprocessing Progam. Quarterly progress report ending February 28, 1979

    International Nuclear Information System (INIS)

    1979-03-01

    This publication continues the quarterly series presenting results of work performed under the Consolidated Reprocessing Program at General Atomic Company. Results of work on this program prior to June 1974 were included in a quarterly series on the HTGR Base Program. The work reported includes the development of unit processes and equipment for reprocessing of High-Temperature Gas-Cooled Reactor (HTGR) fuel, the design and development of an integrated pilot line to demonstrate the head end of HTGR reprocessing using unirradiated fuel materials, and design work in support of Hot Engineering Tests (HET). Work is also described on trade-off studies concerning the required design of facilities and equipment for the large-scale recycle of HTGR fuels in order to guide the development activities for HTGR fuel recycle

  12. Consolidity: Mystery of inner property of systems uncovered

    Directory of Open Access Journals (Sweden)

    Hassen T. Dorrah

    2012-10-01

    Full Text Available This paper uncovers the mystery of consolidity, an inner property of systems that was amazingly hidden. Consolidity also reveals the secrecy of why strong stable and highly controllable systems are not invulnerable of falling and collapsing. Consolidity is measured by its Consolidity Index, defined as the ratio of overall changes of output parameters over combined changes of input and system parameters, all operating in fully fuzzy environment. Under this notion, systems are classified into consolidated, quasi-consolidated, neutrally consolidated, unconsolidated, quasi-unconsolidated and mixed types. The strategy for the implementation of consolidity is elaborated for both natural and man-made existing systems as well as the new developed ones. An important critique arises that the by-product consolidity of natural or built-as-usual system could lead to trapping such systems into a completely undesired unconsolidity. This suggests that the ample number of conventional techniques that do not take system consolidity into account should gradually be changed, and adjusted with improved consolidity-based techniques. Four Golden Rules are highlighted for handling system consolidity, and applied to several illustrative case studies. These case studies cover the consolidity analysis of the Drug Concentration problem, Predator-Prey Population problem, Spread of Infectious Disease problem, AIDS Epidemic problem and Arm Race model. It is demonstrated that consolidity changes are contrary (opposite in sign to changes of both stability and controllability. This is a very significant result showing that our present practice of stressing on building strong stable and highly controllable systems could have already jeopardized the consolidity behavior of an ample family of existing real life systems. It is strongly recommended that the four Golden Rules of consolidity should be enforced as future strict regulations of systems modeling, analysis, design and

  13. Consolidation of titanium matrix composites to maximum density by different hot pressing techniques

    International Nuclear Information System (INIS)

    Montealegre Melendez, I.; Neubauer, E.; Danninger, H.

    2010-01-01

    In this present work, TiMMCs were manufactured through conventional and inductive hot pressing techniques. The starting materials were two titanium based powders as metal matrices, and two types of reinforcements, carbon nanofibres and nano-micro-boron particles. After several manufacturing runs with varying parameters, especially, optimized hot pressing parameters, the titanium compacts were characterized. Density and hardness measurements, chemical analyses and microstructural studies were conducted. The two objectives of this work were achieved. On one hand the influence, in the properties of TiMMCs, of the starting materials as matrix powder and reinforcements was determined. Higher content of impurities from the starting materials affected the hardness and the microstructure of the composites, independently of the manufacturing process. On another hand, the study of variations of the manufacturing process as temperature of consolidation and soaking time was reported. Higher densification was obtained at higher consolidation temperature; however, reaction between the matrix and the carbonaceous reinforcement was detected.

  14. Are distribution coefficients measured from batch experiments meaningful for quantifying retention in compacted material?

    Energy Technology Data Exchange (ETDEWEB)

    Goutelard, F.; Charles, Y.; Page, J. [CEA/DEN/DPC/SECR/L3MR batiment 450, 91191 Gif sur Yvette (France)

    2005-07-01

    Full text of publication follows: To quantify the ability of a clayey material to act as a barrier for radionuclides migration, reliable data on retention properties must be available. The most common method for determining the distribution coefficient, quantifying the radionuclide adsorption, is the batch technique applied to powdered solid. Are these data meaningful for highly compacted minerals? This question is still under debate in literature [1,2]. The aim of the present study is to compare distribution coefficient (KD) value for Cs and Ni onto compacted and dispersed for both Bentonite MX80 and Callovo-Oxfordian clayey material in a simulated site water. Firstly, classical batch sorption experiments are carried on dispersed materials pre-conditioned with the simulated site water at pH 7.3. Radiotracer {sup 137}Cs and {sup 58}Ni are used to investigate the constant-pH isotherm sorption. The bottleneck for measuring distribution coefficient onto highly compacted material lies in a careful monitoring of chemical conditions because they are driven by diffusion processes. For this study, we have chosen to use in-diffusion experiments [3]. Sample size is optimized to reach for high retention level (300 mL/g) the steady state in a reasonable time (3 to 6 month). In order to describe the response surface of compacted distribution coefficient on bentonite MX80, a 2 variables Doehlert matrix has been chosen. In this experimental design, the two variables are density and dispersed distribution coefficient. Bentonite is pre-conditioning before compaction to a density ranging from 1.2 to 1.85 kg/l. The pellet is confined in a cylindrical stainless steel filter (150 {mu}L) closed to both ends. The cell is placed in a tightly closed bottle containing the working solution. After a re-equilibration period (at least 3 weeks), {sup 133}Cs and {sup 59}Ni stable isotope are introduced for monitoring the KD level (between 150 mL/g to 330 mL/g). Radiotracer {sup 137}Cs and {sup 58

  15. Are distribution coefficients measured from batch experiments meaningful for quantifying retention in compacted material?

    International Nuclear Information System (INIS)

    Goutelard, F.; Charles, Y.; Page, J.

    2005-01-01

    Full text of publication follows: To quantify the ability of a clayey material to act as a barrier for radionuclides migration, reliable data on retention properties must be available. The most common method for determining the distribution coefficient, quantifying the radionuclide adsorption, is the batch technique applied to powdered solid. Are these data meaningful for highly compacted minerals? This question is still under debate in literature [1,2]. The aim of the present study is to compare distribution coefficient (KD) value for Cs and Ni onto compacted and dispersed for both Bentonite MX80 and Callovo-Oxfordian clayey material in a simulated site water. Firstly, classical batch sorption experiments are carried on dispersed materials pre-conditioned with the simulated site water at pH 7.3. Radiotracer 137 Cs and 58 Ni are used to investigate the constant-pH isotherm sorption. The bottleneck for measuring distribution coefficient onto highly compacted material lies in a careful monitoring of chemical conditions because they are driven by diffusion processes. For this study, we have chosen to use in-diffusion experiments [3]. Sample size is optimized to reach for high retention level (300 mL/g) the steady state in a reasonable time (3 to 6 month). In order to describe the response surface of compacted distribution coefficient on bentonite MX80, a 2 variables Doehlert matrix has been chosen. In this experimental design, the two variables are density and dispersed distribution coefficient. Bentonite is pre-conditioning before compaction to a density ranging from 1.2 to 1.85 kg/l. The pellet is confined in a cylindrical stainless steel filter (150 μL) closed to both ends. The cell is placed in a tightly closed bottle containing the working solution. After a re-equilibration period (at least 3 weeks), 133 Cs and 59 Ni stable isotope are introduced for monitoring the KD level (between 150 mL/g to 330 mL/g). Radiotracer 137 Cs and 58 Ni are used to quantify the

  16. Effective Stresses in Soil and Rock and Consolidation in Three Dimensions

    DEFF Research Database (Denmark)

    Andersen, Lars

    In the following, the continuum model for a fully saturated porous material is presented. The theory is mainly due to M.A. Biot [?, ?]. We shall only consider a twophase system consisting of a solid skeleton and a single pore fluid, e.g. water. The theory for three-dimensional consolidation...... is developed. Anisotropic permeability of the material is allowed, but for simplicity the analysis is restricted to isotropic linear elastic material behaviour. However, the theory is easily extended to elastoplasticity. Finally, it will be shown that the effective stresses in a porous material may in general...

  17. Statement on the Consolidated Fuel Reprocessing Program

    International Nuclear Information System (INIS)

    Trauger, D.B.

    1984-01-01

    Oak Ridge National Laboratory has chosen the following objectives for future reprocessing plant design: reduced radiation exposure to workers; minimal environmental impact; improved plant operation and maintenance; improved accountability; no plutonium diversion; and reduced overall capital and operating cost. These objectives lead to a plant with totally remote operation. The Breeder Reactor Engineering Test (BRET) has been designed to perform a key role in demonstrating advanced reprocessing technology. It has been scheduled to be available to reprocess spent fuel from the Fast Flux Test Facility. The principal features of the Consolidated Fuel Reprocessing Program and of the BRET facility are appropriate for all reactor types

  18. [Sleep-wake cycle and memory consolidation].

    Science.gov (United States)

    Baratti, Carlos M; Boccia, Mariano M; Blake, Mariano G; Acosta, Gabriela B

    2007-01-01

    Although several hypothesis and theories have been advanced as explanations for the functions of sleep, a unified theory of sleep function remains elusive. Sleep has been implicated in the plastic cerebral changes that underlie learning and memory, in particular those related to memory consolidation of recently acquired new information. Despite steady accumulations of positive findings over the last ten years, the precise role of sleep in memory and brain plasticity is unproven at all. This situation might be solved by more integrated approaches that combine behavioral and neurophysiological measurements in well described in vivo models of neuronal activity and brain plasticity.

  19. Log-inject-log in sand consolidation

    International Nuclear Information System (INIS)

    Murphy, R.P.; Spurlock, J.W.

    1977-01-01

    A method is described for gathering information for the determination of the adequacy of placement of sand consolidating plastic for sand control in oil and gas wells. The method uses a high neutron cross-section tracer which becomes part of the plastic and uses pulsed neutron logging before and after injection of the plastic. Preferably, the method uses lithium, boron, indium, and/or cadmium tracers. Boron oxide is especially useful and can be dissolved in alcohol and mixed with the plastic ingredients

  20. Cadernos Pagu: Consolidating a Field of Studies

    Directory of Open Access Journals (Sweden)

    Iara Beleli

    2003-01-01

    Full Text Available As scientific publications are influential indicators and constitute disciplinary fields, this article reflects on the importance of Cadernos Pagu, published twice a year by Unicamp’s Núcleo de Estudos de Gênero [Gender Studies Center], as it has contributed to the consolidation of that field of studies both through de stimulation and diffusion of knowledge in the area in Brazil. Here gender is no conceived of as a theme, but rather as a categorical distinction, as a distinction between characteristics taken as feminine and masculine, that run through society and, as such, can be felt within any thematic frame.

  1. Proportioning and performance evaluation of self-consolidating concrete

    Science.gov (United States)

    Wang, Xuhao

    A well-proportioned self-consolidating concrete (SCC) mixture can be achieved by controlling the aggregate system, paste quality, and paste quantity. The work presented in this dissertation involves an effort to study and improve particle packing of the concrete system and reduce the paste quantity while maintaining concrete quality and performance. This dissertation is composed of four papers resulting from the study: (1) Assessing Particle Packing Based Self-Consolidating Concrete Mix Design; (2) Using Paste-To-Voids Volume Ratio to Evaluate the Performance of Self-Consolidating Concrete Mixtures; (3) Image Analysis Applications on Assessing Static Stability and Flowability of Self-Consolidating Concrete, and (4) Using Ultrasonic Wave Propagation to Monitor Stiffening Process of Self-Consolidating Concrete. Tests were conducted on a large matrix of SCC mixtures that were designed for cast-in-place bridge construction. The mixtures were made with different aggregate types, sizes, and different cementitious materials. In Paper 1, a modified particle-packing based mix design method, originally proposed by Brouwers (2005), was applied to the design of self-consolidating concrete (SCC) mixs. Using this method, a large matrix of SCC mixes was designed to have a particle distribution modulus (q) ranging from 0.23 to 0.29. Fresh properties (such as flowability, passing ability, segregation resistance, yield stress, viscosity, set time and formwork pressure) and hardened properties (such as compressive strength, surface resistance, shrinkage, and air structure) of these concrete mixes were experimentally evaluated. In Paper 2, a concept that is based on paste-to-voids volume ratio (Vpaste/Vvoids) was employed to assess the performance of SCC mixtures. The relationship between excess paste theory and Vpaste/Vvoids was investigated. The workability, flow properties, compressive strength, shrinkage, and surface resistivity of SCC mixtures were determined at various ages

  2. Benchmarking multi-dimensional large strain consolidation analyses

    International Nuclear Information System (INIS)

    Priestley, D.; Fredlund, M.D.; Van Zyl, D.

    2010-01-01

    Analyzing the consolidation of tailings slurries and dredged fills requires a more extensive formulation than is used for common (small strain) consolidation problems. Large strain consolidation theories have traditionally been limited to 1-D formulations. SoilVision Systems has developed the capacity to analyze large strain consolidation problems in 2 and 3-D. The benchmarking of such formulations is not a trivial task. This paper presents several examples of modeling large strain consolidation in the beta versions of the new software. These examples were taken from the literature and were used to benchmark the large strain formulation used by the new software. The benchmarks reported here are: a comparison to the consolidation software application CONDES0, Townsend's Scenario B and a multi-dimensional analysis of long-term column tests performed on oil sands tailings. All three of these benchmarks were attained using the SVOffice suite. (author)

  3. The neurobiology of consolidations, or, how stable is the engram?

    Science.gov (United States)

    Dudai, Yadin

    2004-01-01

    Consolidation is the progressive postacquisition stabilization of long-term memory. The term is commonly used to refer to two types of processes: synaptic consolidation, which is accomplished within the first minutes to hours after learning and occurs in all memory systems studied so far; and system consolidation, which takes much longer, and in which memories that are initially dependent upon the hippocampus undergo reorganization and may become hippocampal-independent. The textbook account of consolidation is that for any item in memory, consolidation starts and ends just once. Recently, a heated debate has been revitalized on whether this is indeed the case, or, alternatively, whether memories become labile and must undergo some form of renewed consolidation every time they are activated. This debate focuses attention on fundamental issues concerning the nature of the memory trace, its maturation, persistence, retrievability, and modifiability.

  4. Intraperitoneal P-32 for adjuvant and consolidative therapy in ovarian carcinoma

    International Nuclear Information System (INIS)

    Condra, Kellie S.; Mendenhall, William M.; Morgan, Linda S.; Freeman, Debra E.; Marcus, Robert B.; Hagan, Michael P.

    1996-01-01

    Purpose/Objective: To determine the role of intraperitoneal radioactive chromic phosphate (P-32) in the treatment of patients with ovarian carcinoma. Survival results, patterns of recurrence, and treatment morbidity are reported for patients treated adjuvantly after primary surgery and for patients treated with the intent of consolidation after second-look laparotomy. Materials and Methods: Between 1976 and 1993, 25 patients with ovarian carcinoma were treated with 15 mCi P-32 as adjuvant therapy and 43 patients received P-32 as consolidation after second-look laparotomy. The majority of patients (13 of 19) treated adjuvantly had high-risk early-stage disease (IAG 3, IBG 2-3, IC) or more advanced stages (6 patients). Thirty-nine patients received consolidative P-32 after negative second-look laparotomy (35 Stage II-IV and 4 Stage I) and 4 Stage III patients were treated after positive second-look laparotomy. All patients had 2-year minimum follow-up (median, 7.9 years). Results: Ten-year abdominal control and cause-specific survival rates for adjuvant P-32 were 83% and 82%, respectively. For patients treated with consolidative P-32, 5-year abdominal control and cause-specific survival rates were 65% and 78%, respectively. The 5-year cause-specific survival rate for 35 patients with Stage II-IV disease treated with consolidative P-32 after negative second-look laparotomy was 81%. A component of peritoneal failure was the primary mode of recurrence (15 of 22 failures). Four patients required surgical intervention for small-bowel obstruction. No patients died of treatment-related complications. Conclusion: P-32 is well tolerated with acceptable toxicity. In comparing our results to the literature, adjuvant P-32 appears to offer improved cause-specific survival compared with observation alone and equivalent cause-specific survival compared with adjuvant chemotherapy. Consolidative P-32 after negative second-look laparotomy resulted in improved 5-year cause

  5. FY:15 Transport Properties of Run-of-Mine Salt Backfill ? Unconsolidated to Consolidated.

    Energy Technology Data Exchange (ETDEWEB)

    Dewers, Thomas [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Heath, Jason E. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States); Leigh, Christi D. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2015-09-28

    The nature of geologic disposal of nuclear waste in salt formations requires validated and verified two-phase flow models of transport of brine and gas through intact, damaged, and consolidating crushed salt. Such models exist in other realms of subsurface engineering for other lithologic classes (oil and gas, carbon sequestration etc. for clastics and carbonates) but have never been experimentally validated and parameterized for salt repository scenarios or performance assessment. Models for waste release scenarios in salt back-fill require phenomenological expressions for capillary pressure and relative permeability that are expected to change with degree of consolidation, and require experimental measurement to parameterize and validate. This report describes a preliminary assessment of the influence of consolidation (i.e. volume strain or porosity) on capillary entry pressure in two phase systems using mercury injection capillary pressure (MICP). This is to both determine the potential usefulness of the mercury intrusion porosimetry method, but also to enable a better experimental design for these tests. Salt consolidation experiments are performed using novel titanium oedometers, or uniaxial compression cells often used in soil mechanics, using sieved run-of-mine salt from the Waste Isolation Pilot Plant (WIPP) as starting material. Twelve tests are performed with various starting amounts of brine pore saturation, with axial stresses up to 6.2 MPa (~900 psi) and temperatures to 90°C. This corresponds to UFD Work Package 15SN08180211 milestone “FY:15 Transport Properties of Run-of-Mine Salt Backfill – Unconsolidated to Consolidated”. Samples exposed to uniaxial compression undergo time-dependent consolidation, or creep, to various degrees. Creep volume strain-time relations obey simple log-time behavior through the range of porosities (~50 to 2% as measured); creep strain rate increases with temperature and applied stress as expected. Mercury porosimetry

  6. Final Report: Improving the understanding of the coupled thermal-mechanical-hydrologic behavior of consolidating granular salt

    Energy Technology Data Exchange (ETDEWEB)

    Stormont, John [Univ. of New Mexico, Albuquerque, NM (United States); Lampe, Brandon [Univ. of New Mexico, Albuquerque, NM (United States); Mills, Melissa [Univ. of New Mexico, Albuquerque, NM (United States); Paneru, Laxmi [Univ. of New Mexico, Albuquerque, NM (United States); Lynn, Timothy [Univ. of New Mexico, Albuquerque, NM (United States); Piya, Aayush [Univ. of New Mexico, Albuquerque, NM (United States)

    2017-09-09

    The goal of this project is to improve the understanding of key aspects of the coupled thermal-mechanical-hydrologic response of granular (or crushed) salt used as a seal material for shafts, drifts, and boreholes in mined repositories in salt. The project is organized into three tasks to accomplish this goal: laboratory measurements of granular salt consolidation (Task 1), microstructural observations on consolidated samples (Task 2), and constitutive model development and evaluation (Task 3). Task 1 involves laboratory measurements of salt consolidation along with thermal properties and permeability measurements conducted under a range of temperatures and stresses expected for potential mined repositories in salt. Testing focused on the role of moisture, temperature and stress state on the hydrologic (permeability) and thermal properties of consolidating granular salt at high fractional densities. Task 2 consists of microstructural observations made on samples after they have been consolidated to interpret deformation mechanisms and evaluate the ability of the constitutive model to predict operative mechanisms under different conditions. Task 3 concerns the development of the coupled thermal-mechanical-hydrologic constitutive model for granular salt consolidation. The measurements and observations in Tasks 1 and 2 were used to develop a thermal-mechanical constitutive model. Accomplishments and status from each of these efforts is reported in subsequent sections of this report

  7. Tomographic findings of lobar consolidation in primary pulmonary tuberculosis; Aspectos tomograficos da consolidacao lobar na tuberculose pulmonar primaria

    Energy Technology Data Exchange (ETDEWEB)

    Pereira, Bruno Alberto Falcao [Hopital Europeen Georges Pompidou, Paris (France); Macedo, Solange Goncalves David de [Hospital Municipal Jesus, Rio de Janeiro, RJ (Brazil). Setor de Pneumologia; Nogueira, Renata do Amaral [Clinica de Diagnostico por Imagem (CDPI), Rio de Janeiro, RJ (Brazil). Setor de Pediatria; Castiel, Lola Celeste Pantoja [Clinica Radiologica Dr. Samuel Castiel, Porto Velho, RO (Brazil); Penna, Claudia Renata Rezende [Hospital Municipal Jesus, Rio de Janeiro, RJ (Brazil). Servico de Radiologia Pediatrica], e-mail: cr-penna@uol.com.br

    2009-03-15

    Objective: To describe tomographic findings of lobar consolidation as early manifestation of primary pulmonary tuberculosis. Materials and methods: The present study was developed at Hospital Municipal Jesus, Rio de Janeiro, RJ, Brazil, in the period between 2002 and 2006, retrospectively evaluating tomographic findings in four children aged from 3 to 14 months with lobar consolidation as an early manifestation of primary pulmonary tuberculosis. Results: The most frequently found radiological pattern was lobar consolidation with calcifications, cavitation and intermingle necrotic areas, associated with bulging fissure. Signs of bronchogenic dissemination and lymph node enlargement were observed in all of the four children. Consolidation with a pseudotumor aspect and masslike effect was observed in one case. Conclusion: The cases included in the present study have demonstrated that primary pulmonary tuberculosis manifested as lobar consolidation presents typical tomographic images such as cavitation, hypodense areas and calcifications intermingled with consolidation. The association with lymph node enlargement with central necrosis and signs of bronchogenic dissemination reinforce the diagnosis of tuberculosis. (author)

  8. Memory Consolidation and Neural Substrate of Reward

    Directory of Open Access Journals (Sweden)

    Redolar-Ripoll, Diego

    2012-08-01

    Full Text Available The aim of this report is to analyze the relationships between reward and learning and memory processes. Different studies have described how information about rewards influences behavior and how the brain uses this reward information to control learning and memory processes. Reward nature seems to be processed in different ways by neurons in different brain structures, ranging from the detection and perception of rewards to the use of information about predicted rewards for the control of goal-directed behavior. The neural substrate underling this processing of reward information is a reliable way of improving learning and memory processes. Evidence from several studies indicates that this neural system can facilitate memory consolidation in a wide variety of learning tasks. From a molecular perspective, certain cardinal features of reward have been described as forms of memory. Studies of human addicts and studies in animal models of addiction show that chronic drug exposure produces stable changes in the brain at the cellular and molecular levels that underlie the long-lasting behavioral plasticity associated with addiction. These molecular and cellular adaptations involved in addiction are also implicated in learning and memory processes. Dopamine seems to be a critical common signal to activate different genetic mechanisms that ultimately remodel synapses and circuits. Despite memory is an active and complex process mediated by different brain areas, the neural substrate of reward is able to improve memory consolidation in a several paradigms. We believe that there are many equivalent traits between reward and learning and memory processes.

  9. Commercial Consolidation Model Applied to Transport Infrastructure

    Energy Technology Data Exchange (ETDEWEB)

    Guilherme de Aragão, J.J.; Santos Fontes Pereira, L. dos; Yamashita, Y.

    2016-07-01

    Since the 1990s, transport concessions, including public-private partnerships (PPPs), have been increasingly adopted by governments as an alternative for financing and operations in public investments, especially in transport infrastructure. The advantage pointed out by proponents of these models lies in merging the expertise and capital of the private sector to the public interest. Several arrangements are possible and have been employed in different cases. After the duration of the first PPP contracts in transportation, many authors have analyzed the success and failure factors of partnerships. The occurrence of failures in some stages of the process can greatly encumber the public administration, incurring losses to the fiscal responsibility of the competent bodies. This article aims to propose a new commercial consolidation model applied to transport infrastructure to ensure fiscal sustainability and overcome the weaknesses of current models. Initially, a systematic review of the literature covering studies on transport concessions between 1990 and 2015 is offered, where the different approaches between various countries are compared and the critical success factors indicated in the studies are identified. In the subsequent part of the paper, an approach for the commercial consolidation of the infrastructure concessions is presented, where the concessionary is paid following a finalistic performance model, which includes the overall fiscal balance of regional growth. Finally, the papers analyses the usefulness of the model in coping with the critical success factors explained before. (Author)

  10. Interacting Brain Systems Modulate Memory Consolidation

    Science.gov (United States)

    McIntyre, Christa K.; McGaugh, James L.; Williams, Cedric L.

    2011-01-01

    Emotional arousal influences the consolidation of long-term memory. This review discusses experimental approaches and relevant findings that provide the foundation for current understanding of coordinated interactions between arousal activated peripheral hormones and the brain processes that modulate memory formation. Rewarding or aversive experiences release the stress hormones epinephrine (adrenalin) and glucocorticoids from the adrenal glands into the bloodstream. The effect of these hormones on memory consolidation depends upon binding of norepinephrine to beta-adrenergic receptors in the basolateral complex of the amygdala (BLA). Much evidence indicates that the stress hormones influence release of norepinephrine in the BLA through peripheral actions on the vagus nerve which stimulates, through polysynaptic connections, cells of the locus coeruleus to release norepinephrine. The BLA influences memory storage by actions on synapses, distributed throughout the brain, that are engaged in sensory and cognitive processing at the time of amygdala activation. The implications of the activation of these stress-activated memory processes are discussed in relation to stress-related memory disorders. PMID:22085800

  11. Factors affecting the consolidation of steam generator sludge

    Energy Technology Data Exchange (ETDEWEB)

    Turner, C. W.; Shamsuzzaman, K.; Tapping, R. L.

    1993-02-15

    It is hypothesized that sludge consolidation is promoted by chemical reactions involving the various sludge constituents, although the hardness of the final product will also depend on the total porosity. Oxidizing conditions and higher temperatures produce a harder sludge. The precipitation of Zn{sub 2}SiO{sub 4}, a potential binding agent, may also promote sludge consolidation. Several solutions to prevent sludge consolidation are suggested. (Author) 3 figs., 4 tabs., 3 refs.

  12. How useful is consolidation of public sector entities' financial statements ?

    OpenAIRE

    Soguel, N.; Bucher, R.

    2013-01-01

    Whether or not to consolidate financial statements is dealt with in IPSAS#6. This standard is by and large based on IAS#27. It deals with the criterion according to which an entity's financial statements should be considered and which consolidation technique should be used. However, it remains silent when it comes to exposing the reason why a public sector entity should consolidate its financial statements. The literature is almost as silent as IPSAS on this issue. Which means that there is a...

  13. Failure envelope approach for consolidated undrained capacity of shallow foundations

    OpenAIRE

    Vulpe, Cristina; Gourvenec, Susan; Leman, Billy; Fung, Kah Ngii

    2016-01-01

    A generalized framework is applied to predict consolidated undrained VHM failure envelopes for surface circular and strip foundations. The failure envelopes for consolidated undrained conditions are shown to be scaled from those for unconsolidated undrained conditions by the uniaxial consolidated undrained capacities, which are predicted through a theoretical framework based on fundamental critical state soil mechanics. The framework is applied to results from small-strain finite-element anal...

  14. Post-study caffeine administration enhances memory consolidation in humans.

    Science.gov (United States)

    Borota, Daniel; Murray, Elizabeth; Keceli, Gizem; Chang, Allen; Watabe, Joseph M; Ly, Maria; Toscano, John P; Yassa, Michael A

    2014-02-01

    It is currently not known whether caffeine has an enhancing effect on long-term memory in humans. We used post-study caffeine administration to test its effect on memory consolidation using a behavioral discrimination task. Caffeine enhanced performance 24 h after administration according to an inverted U-shaped dose-response curve; this effect was specific to consolidation and not retrieval. We conclude that caffeine enhanced consolidation of long-term memories in humans.

  15. Sleep-related declarative memory consolidation and verbal replay during sleep talking in patients with REM sleep behavior disorder.

    Directory of Open Access Journals (Sweden)

    Ginevra Uguccioni

    Full Text Available OBJECTIVE: To determine if sleep talkers with REM sleep behavior disorder (RBD would utter during REM sleep sentences learned before sleep, and to evaluate their verbal memory consolidation during sleep. METHODS: Eighteen patients with RBD and 10 controls performed two verbal memory tasks (16 words from the Free and Cued Selective Reminding Test and a 220-263 word long modified Story Recall Test in the evening, followed by nocturnal video-polysomnography and morning recall (night-time consolidation. In 9 patients with RBD, daytime consolidation (morning learning/recall, evening recall was also evaluated with the modified Story Recall Test in a cross-over order. Two RBD patients with dementia were studied separately. Sleep talking was recorded using video-polysomnography, and the utterances were compared to the studied texts by two external judges. RESULTS: Sleep-related verbal memory consolidation was maintained in patients with RBD (+24±36% words as in controls (+9±18%, p=0.3. The two demented patients with RBD also exhibited excellent nighttime consolidation. The post-sleep performance was unrelated to the sleep measures (including continuity, stages, fragmentation and apnea-hypopnea index. Daytime consolidation (-9±19% was worse than night-time consolidation (+29±45%, p=0.03 in the subgroup of 9 patients with RBD. Eleven patients with RBD spoke during REM sleep and pronounced a median of 20 words, which represented 0.0003% of sleep with spoken language. A single patient uttered a sentence that was judged to be semantically (but not literally related to the text learned before sleep. CONCLUSION: Verbal declarative memory normally consolidates during sleep in patients with RBD. The incorporation of learned material within REM sleep-associated sleep talking in one patient (unbeknownst to himself at the semantic level suggests a replay at a highly cognitive creative level.

  16. 100-N pilot project: Proposed consolidated groundwater monitoring program

    International Nuclear Information System (INIS)

    Borghese, J.V.; Hartman, M.J.; Lutrell, S.P.; Perkins, C.J.; Zoric, J.P.; Tindall, S.C.

    1996-11-01

    This report presents a proposed consolidated groundwater monitoring program for the 100-N Pilot Project. This program is the result of a cooperative effort between the Hanford Site contractors who monitor the groundwater beneath the 100-N Area. The consolidation of the groundwater monitoring programs is being proposed to minimize the cost, time, and effort necessary for groundwater monitoring in the 100-N Area, and to coordinate regulatory compliance activities. The integrity of the subprograms requirements remained intact during the consolidation effort. The purpose of this report is to present the proposed consolidated groundwater monitoring program and to summarize the process by which it was determined

  17. Fuel consolidation and compaction and storage of NFBC

    International Nuclear Information System (INIS)

    Fuierer, T.

    1992-01-01

    Rochester Gas and Electric Corporation (RG ampersand E) has been involved in two separate fuel consolidation demonstration programs. One of those programs resulted in identifying some problems that may be resolved in consolidation hardware compaction and storage in order for consolidation to be attractive. In conjunction with the Electric Power Research Institute (EPRI), a study was recently performed on hardware compaction and storage. Consolidation is probably not a commercial alternative at this point in time because there are still several problems that must be resolved. There are some potential advantages of fuel consolidation. Consolidation has attractive economics and can minimize the institutional impacts of expanding spent fuel storage by internalizing spent fuel storage operations. The licensing effort is fairly simple. Consolidation may be less likely to have public intervention since the storage expansion will occur inside the plant. Consolidation can be subcontracted and the equipment is temporary. It can be used in conjunction with other storage expansion technologies such as dry storage. Fewer dry storage casks would be needed to store consolidated fuel than would be necessary for intact spent fuel

  18. Effects of inorganic and organic amendment on soil chemical properties, enzyme activities, microbial community and soil quality in yellow clayey soil.

    Directory of Open Access Journals (Sweden)

    Zhanjun Liu

    Full Text Available Understanding the effects of external organic and inorganic components on soil fertility and quality is essential for improving low-yielding soils. We conducted a field study over two consecutive rice growing seasons to investigate the effect of applying chemical fertilizer (NPK, NPK plus green manure (NPKG, NPK plus pig manure (NPKM, and NPK plus straw (NPKS on the soil nutrient status, enzyme activities involved in C, N, P, and S cycling, microbial community and rice yields of yellow clayey soil. Results showed that the fertilized treatments significantly improved rice yields over the first three experimental seasons. Compared with the NPK treatment, organic amendments produced more favorable effects on soil productivity. Notably, the NPKM treatment exhibited the highest levels of nutrient availability, microbial biomass carbon (MBC, activities of most enzymes and the microbial community. This resulted in the highest soil quality index (SQI and rice yield, indicating better soil fertility and quality. Significant differences in enzyme activities and the microbial community were observed among the treatments, and redundancy analysis showed that MBC and available N were the key determinants affecting the soil enzyme activities and microbial community. The SQI score of the non-fertilized control (0.72 was comparable to that of the NPK (0.77, NPKG (0.81 and NPKS (0.79 treatments but significantly lower compared with NPKM (0.85. The significant correlation between rice yield and SQI suggests that SQI can be a useful to quantify soil quality changes caused by different agricultural management practices. The results indicate that application of NPK plus pig manure is the preferred option to enhance SOC accumulation, improve soil fertility and quality, and increase rice yield in yellow clayey soil.

  19. A novel hyper-viscoelastic model for consolidation of toughened prepregs under processing conditions

    OpenAIRE

    Belnoue, J.P.-H.; Nixon-Pearson, O.J.; Ivanov, D.; Hallett, S.R.

    2016-01-01

    The paper presents a new modelling concept for describing the compressibility of toughened uncured prepregs over a wide range of processing conditions (i.e. automatic fibre deposition, hot debulking and pre-curing consolidation). The primary challenge of the work is to simulate the material response due complex flow and deformation mechanisms. This generation of prepreg systems exhibits both percolation (bleeding) flow typical for conventional thermosets, where the pressure gradient causes re...

  20. Nanoparticles for cultural heritage conservation: calcium and barium hydroxide nanoparticles for wall painting consolidation.

    Science.gov (United States)

    Giorgi, Rodorico; Ambrosi, Moira; Toccafondi, Nicola; Baglioni, Piero

    2010-08-16

    Nanotechnology provides new concepts and materials for the consolidation and protection of wall paintings. In particular, humble calcium and barium hydroxide nanoparticles offer a versatile and highly efficient tool to combat the main degradation processes altering wall paintings. Clear example of the efficacy and potentiality of nanotechnology is represented by the conservation in situ of Maya wall paintings in the archaeological area in Calakmul (Mexico).

  1. Consolidation of cloud computing in ATLAS

    CERN Document Server

    AUTHOR|(INSPIRE)INSPIRE-00224309; The ATLAS collaboration; Cordeiro, Cristovao; Hover, John; Kouba, Tomas; Love, Peter; Mcnab, Andrew; Schovancova, Jaroslava; Sobie, Randall; Giordano, Domenico

    2017-01-01

    Throughout the first half of LHC Run 2, ATLAS cloud computing has undergone a period of consolidation, characterized by building upon previously established systems, with the aim of reducing operational effort, improving robustness, and reaching higher scale. This paper describes the current state of ATLAS cloud computing. Cloud activities are converging on a common contextualization approach for virtual machines, and cloud resources are sharing monitoring and service discovery components. We describe the integration of Vacuum resources, streamlined usage of the Simulation at Point 1 cloud for offline processing, extreme scaling on Amazon compute resources, and procurement of commercial cloud capacity in Europe. Finally, building on the previously established monitoring infrastructure, we have deployed a real-time monitoring and alerting platform which coalesces data from multiple sources, provides flexible visualization via customizable dashboards, and issues alerts and carries out corrective actions in resp...

  2. Consolidation of Cloud Computing in ATLAS

    CERN Document Server

    AUTHOR|(INSPIRE)INSPIRE-00224309; The ATLAS collaboration; Cordeiro, Cristovao; Di Girolamo, Alessandro; Hover, John; Kouba, Tomas; Love, Peter; Mcnab, Andrew; Schovancova, Jaroslava; Sobie, Randall

    2016-01-01

    Throughout the first year of LHC Run 2, ATLAS Cloud Computing has undergone a period of consolidation, characterized by building upon previously established systems, with the aim of reducing operational effort, improving robustness, and reaching higher scale. This paper describes the current state of ATLAS Cloud Computing. Cloud activities are converging on a common contextualization approach for virtual machines, and cloud resources are sharing monitoring and service discovery components. We describe the integration of Vac resources, streamlined usage of the High Level Trigger cloud for simulation and reconstruction, extreme scaling on Amazon EC2, and procurement of commercial cloud capacity in Europe. Building on the previously established monitoring infrastructure, we have deployed a real-time monitoring and alerting platform which coalesces data from multiple sources, provides flexible visualization via customizable dashboards, and issues alerts and carries out corrective actions in response to problems. ...

  3. Particle filtration in consolidated granular systems

    International Nuclear Information System (INIS)

    Schwartz, L.M.; Wilkinson, D.J.; Bolsterli, M.; Hammond, P.

    1993-01-01

    Grain-packing algorithms are used to model the mechanical trapping of dilute suspensions of particles by consolidated granular media. We study the distribution of filtrate particles, the formation of a damage zone (internal filter cake), and the transport properties of the host--filter-cake composite. At the early stages of filtration, our simulations suggest simple relationships between the structure of the internal filter cake and the characteristics of the underlying host matrix. These relationships are then used to describe the dynamics of the filtration process. Depending on the grain size and porosity of the host matrix, calculated filtration rates may either be greater than (spurt loss) or less than (due to internal clogging) those predicted by standard surface-filtration models

  4. LS1: electrical engineering upgrades and consolidation

    International Nuclear Information System (INIS)

    Duval, F.

    2012-01-01

    3 different types of activities are planned by the Engineering Department Electrical Engineering (EN-EL) Group for the first long shut down (LS1). First, the consolidation of EN-EL's ageing infrastructure elements. It is part of a 15- year programme aiming at increasing the reliability and availability of the power distribution network. Secondly, the maintenance of the accelerators infrastructure. In addition to the usual periodic operations and those delayed until LS1, the group will address more demanding activities like the replacement campaigns for irradiated cables and non-radiation resistant fibres as well as the removal of unused cables in particularly overcrowded areas. Thirdly, a vast amount of user copper and optical fibre cabling requests: EN-EL estimates that only 50% of LS1 requests are currently known. The main activities will be EN-EL's contributions to the R2E project, BE-BI upgrade projects, and the RF upgrade project in SPS BA3

  5. Consolidation of cloud computing in ATLAS

    Science.gov (United States)

    Taylor, Ryan P.; Domingues Cordeiro, Cristovao Jose; Giordano, Domenico; Hover, John; Kouba, Tomas; Love, Peter; McNab, Andrew; Schovancova, Jaroslava; Sobie, Randall; ATLAS Collaboration

    2017-10-01

    Throughout the first half of LHC Run 2, ATLAS cloud computing has undergone a period of consolidation, characterized by building upon previously established systems, with the aim of reducing operational effort, improving robustness, and reaching higher scale. This paper describes the current state of ATLAS cloud computing. Cloud activities are converging on a common contextualization approach for virtual machines, and cloud resources are sharing monitoring and service discovery components. We describe the integration of Vacuum resources, streamlined usage of the Simulation at Point 1 cloud for offline processing, extreme scaling on Amazon compute resources, and procurement of commercial cloud capacity in Europe. Finally, building on the previously established monitoring infrastructure, we have deployed a real-time monitoring and alerting platform which coalesces data from multiple sources, provides flexible visualization via customizable dashboards, and issues alerts and carries out corrective actions in response to problems.

  6. Gradual consolidation of synesthesia during adolescence

    DEFF Research Database (Denmark)

    Sørensen, Thomas Alrik; Nordfang, Maria; Ásgeirsson, Árni Gunnar

    2016-01-01

    ), visual priming (Mattingley, Rich, Yelland, & Bradshaw, 2001), and the Stroop task (Mills, Boteler, & Oliver, 1999). In a recent study Ásgeirsson, Nordfang, & Sørensen (2015) isolated specific components of attention that are modulated by synesthesia, and which seem to correspond to attentional changes......), and recently Simner & Bain (2013) has convincingly shown that consolidation of colour-grapheme synaesthesia develop during childhood and early adolescence. Together these studies seem to suggest that the attentional effects seen in adult observers who have colour-grapheme synaesthesia may in fact reflect......Synesthesia is a rare condition in the normal observer where an inducer quale is consistently followed by a second, concurrent quale (Grossenbacher & Lovelace, 2001). Several studies have demonstrated the effects of synesthesia through a number of objective measures; like visual search (Laeng, 2009...

  7. ER Consolidated Quarterly Report October 2014

    Energy Technology Data Exchange (ETDEWEB)

    Cochran, John R. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2014-10-01

    This Environmental Restoration Operations (ER) Consolidated Quarterly Report (ER Quarterly Report) provides the status of ongoing corrective actions and related Long- Term Stewardship (LTS) activities being implemented by Sandia National Laboratories, New Mexico (SNL/NM) ER for the April, May, and June 2014 quarterly reporting period. Section 2.0 provides the status of ER Operations activities including closure activities for the Mixed Waste Landfill (MWL), project management and site closure, and hydrogeologic characterizations. Section 3.0 provides the status of LTS activities that relate to the Chemical Waste Landfill (CWL) and the associated Corrective Action Management Unit (CAMU). Section 4.0 provides the references noted in Section I of this report.

  8. An analytical solution for two-dimensional vacuum preloading combined with electro-osmosis consolidation using EKG electrodes.

    Directory of Open Access Journals (Sweden)

    Yang Shen

    Full Text Available China is a country with vast territory, but economic development and population growth have reduced the usable land resources in recent years. Therefore, reclamation by pumping and filling is carried out in eastern coastal regions of China in order to meet the needs of urbanization. However, large areas of reclaimed land need rapid drainage consolidation treatment. Based on past researches on how to improve the treatment efficiency of soft clay using vacuum preloading combined with electro-osmosis, a two-dimensional drainage plane model was proposed according to the Terzaghi and Esrig consolidation theory. However, the analytical solution using two-dimensional plane model was never involved. Current analytical solutions can't have a thorough theoretical analysis of practical engineering and give relevant guidance. Considering the smearing effect and the rectangle arrangement pattern, an analytical solution is derived to describe the behavior of pore-water and the consolidation process by using EKG (electro-kinetic geo synthetics materials. The functions of EKG materials include drainage, electric conduction and corrosion resistance. Comparison with test results is carried out to verify the analytical solution. It is found that the measured value is larger than the applied vacuum degree because of the stacking effect of the vacuum preloading and electro-osmosis. The trends of the mean measured value and the mean analytical value processes are comparable. Therefore, the consolidation model can accurately assess the change in pore-water pressure and the consolidation process during vacuum preloading combined with electro-osmosis.

  9. An analytical solution for two-dimensional vacuum preloading combined with electro-osmosis consolidation using EKG electrodes

    Science.gov (United States)

    Qiu, Chenchen; Li, Yande

    2017-01-01

    China is a country with vast territory, but economic development and population growth have reduced the usable land resources in recent years. Therefore, reclamation by pumping and filling is carried out in eastern coastal regions of China in order to meet the needs of urbanization. However, large areas of reclaimed land need rapid drainage consolidation treatment. Based on past researches on how to improve the treatment efficiency of soft clay using vacuum preloading combined with electro-osmosis, a two-dimensional drainage plane model was proposed according to the Terzaghi and Esrig consolidation theory. However, the analytical solution using two-dimensional plane model was never involved. Current analytical solutions can’t have a thorough theoretical analysis of practical engineering and give relevant guidance. Considering the smearing effect and the rectangle arrangement pattern, an analytical solution is derived to describe the behavior of pore-water and the consolidation process by using EKG (electro-kinetic geo synthetics) materials. The functions of EKG materials include drainage, electric conduction and corrosion resistance. Comparison with test results is carried out to verify the analytical solution. It is found that the measured value is larger than the applied vacuum degree because of the stacking effect of the vacuum preloading and electro-osmosis. The trends of the mean measured value and the mean analytical value processes are comparable. Therefore, the consolidation model can accurately assess the change in pore-water pressure and the consolidation process during vacuum preloading combined with electro-osmosis. PMID:28771496

  10. Reward value determines memory consolidation in parasitic wasps.

    Science.gov (United States)

    Kruidhof, H Marjolein; Pashalidou, Foteini G; Fatouros, Nina E; Figueroa, Ilich A; Vet, Louise E M; Smid, Hans M; Huigens, Martinus E

    2012-01-01

    Animals can store learned information in their brains through a series of distinct memory forms. Short-lasting memory forms can be followed by longer-lasting, consolidated memory forms. However, the factors determining variation in memory consolidation encountered in nature have thus far not been fully elucidated. Here, we show that two parasitic wasp species belonging to different families, Cotesia glomerata (Hymenoptera: Braconidae) and Trichogramma evanescens (Hymenoptera; Trichogrammatidae), similarly adjust the memory form they consolidate to a fitness-determining reward: egg-laying into a host-insect that serves as food for their offspring. Protein synthesis-dependent long-term memory (LTM) was consolidated after single-trial conditioning with a high-value host. However, single-trial conditioning with a low-value host induced consolidation of a shorter-lasting memory form. For Cotesia glomerata, we subsequently identified this shorter-lasting memory form as anesthesia-resistant memory (ARM) because it was not sensitive to protein synthesis inhibitors or anesthesia. Associative conditioning using a single reward of different value thus induced a physiologically different mechanism of memory formation in this species. We conclude that the memory form that is consolidated does not only change in response to relatively large differences in conditioning, such as the number and type of conditioning trials, but is also sensitive to more subtle differences, such as reward value. Reward-dependent consolidation of exclusive ARM or LTM provides excellent opportunities for within-species comparison of mechanisms underlying memory consolidation.

  11. Reward Value Determines Memory Consolidation in Parasitic Wasps

    NARCIS (Netherlands)

    Kruidhof, H.M.; Pashalidou, F.G.; Fatouros, N.E.; Figueroa, I.A.; Vet, L.E.M.; Smid, H.M.; Huigens, M.E.

    2012-01-01

    Animals can store learned information in their brains through a series of distinct memory forms. Short-lasting memory forms can be followed by longer-lasting, consolidated memory forms. However, the factors determining variation in memory consolidation encountered in nature have thus far not been

  12. Memory Consolidation and Gene Expression in "Periplaneta Americana"

    Science.gov (United States)

    Strausfeld, Nicholas J.; Pinter, Marianna; Lent, David D.

    2005-01-01

    A unique behavioral paradigm has been developed for "Periplaneta americana" that assesses the timing and success of memory consolidation leading to long-term memory of visual-olfactory associations. The brains of trained and control animals, removed at the critical consolidation period, were screened by two-directional suppression subtractive…

  13. The role of the ventromedial prefrontal cortex in memory consolidation

    NARCIS (Netherlands)

    Nieuwenhuis, I.L.C.; Takashima, A.

    2011-01-01

    System-level memory consolidation theory posits that the hippocampus initially links the neocortical representations, followed by a shift to a hippocampus-independent neocortical network. With consolidation, an increase in activity in the human subgenual ventromedial prefrontal cortex (vmPFC) has

  14. Simulation and video software development for soil consolidation testing

    NARCIS (Netherlands)

    Karim, Usama F.A.

    2003-01-01

    The development techniques and file structures of CTM, a novel multi-media (computer simulation and video) package on consolidation and laboratory consolidation testing, are presented in this paper. A courseware tool called Authorware proved to be versatile for building the package and the paper

  15. 7 CFR 1717.615 - Consolidations and mergers.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 11 2010-01-01 2010-01-01 false Consolidations and mergers. 1717.615 Section 1717.615... Controls § 1717.615 Consolidations and mergers. A distribution or power supply borrower may without the..., merger, conveyance or transfer shall be on such terms as shall fully preserve the lien and security of...

  16. 7 CFR 1782.15 - Mergers and consolidations.

    Science.gov (United States)

    2010-01-01

    ... 7 Agriculture 12 2010-01-01 2010-01-01 false Mergers and consolidations. 1782.15 Section 1782.15... AGRICULTURE (CONTINUED) SERVICING OF WATER AND WASTE PROGRAMS § 1782.15 Mergers and consolidations. Mergers... transaction under consideration and the unique facts involved in each transaction. Mergers occur when two or...

  17. 12 CFR 931.5 - Liquidation, merger, or consolidation.

    Science.gov (United States)

    2010-01-01

    ... 12 Banks and Banking 7 2010-01-01 2010-01-01 false Liquidation, merger, or consolidation. 931.5 Section 931.5 Banks and Banking FEDERAL HOUSING FINANCE BOARD FEDERAL HOME LOAN BANK RISK MANAGEMENT AND CAPITAL STANDARDS FEDERAL HOME LOAN BANK CAPITAL STOCK § 931.5 Liquidation, merger, or consolidation. The...

  18. Bortezomib consolidation after autologous stem cell transplantation in multiple myeloma

    DEFF Research Database (Denmark)

    Mellqvist, Ulf-Henrik; Gimsing, Peter; Hjertner, Oyvind

    2013-01-01

    The Nordic Myeloma Study Group conducted an open randomized trial to compare bortezomib as consolidation therapy given after high-dose therapy and autologous stem cell transplantation (ASCT) with no consolidation in bortezomib-naive patients with newly diagnosed multiple myeloma. Overall, 370...

  19. Accounting Treatment for Separate and Consolidated Financial Statements

    Directory of Open Access Journals (Sweden)

    Iuliana Oana Mihai

    2015-09-01

    Full Text Available The rules governing the financial statements consolidation have been subject for debates for many years. The financial crisis in 2008 accelerated changes toward new improved standards. The main objective of this article is to explain the key parts of the IASB standards for consolidation of financial statements.

  20. Success Modulates Consolidation of a Visuomotor Adaptation Task

    Science.gov (United States)

    Trempe, Maxime; Sabourin, Maxime; Proteau, Luc

    2012-01-01

    Consolidation is a time-dependent process that is responsible for the storage of information in long-term memory. As such, it plays a crucial role in motor learning. Prior research suggests that some consolidation processes are triggered only when the learner experiences some success during practice. In the present study, we tested whether…

  1. Phase II Study of Consolidation Chemotherapy After Concurrent Chemoradiation in Cervical Cancer: Preliminary Results

    International Nuclear Information System (INIS)

    Choi, Chel Hun; Lee, Jeong-Won; Kim, Tae-Joong; Kim, Woo Young; Nam, Hee Rim; Kim, Byoung-Gie; Huh, Seung Jae; Lee, Je-Ho; Bae, Duk-Soo

    2007-01-01

    Purpose: Our aim was to determine the efficacy of consolidation chemotherapy after concurrent chemoradiation (CCRT) using high-dose-rate brachytherapy in patients with locally advanced cervical carcinoma. Methods and Materials: Patients with cervical carcinoma (FIGO stage IB2-IVA) were treated with external beam radiation therapy to the whole pelvis (50.4 Gy) and high-dose-rate brachytherapy (24 Gy to point A). Cisplatin 60 mg/m 2 (Day 1) and 5-fluorouracil 1000 mg/m 2 (Days 1-5) were given every 3 weeks starting concurrently with the radiation and followed by 3 more cycles of consolidation for a total of 6 cycles. Results: Thirty patients (94%) received 3 more cycles of post-CCRT consolidation chemotherapy and were evaluable for the toxicity and efficacy of consolidation. The most common toxicities of Grade 2 or higher were nausea or vomiting (47%) and anemia (33%). Late complications of the rectum and bladder occurred in 13% and 6% of the patients, respectively. The clinical complete response rate was 87% (95% CI, 75%-99%). During a median follow-up of 27 months (range, 6-58 months), 5 patients (17%) had recurrence; the sites of failure were 3 (10%) inside the radiation field and 2 (7%) outside the radiation field. The estimated 3-year progression-free survival rate was 83% (95% CI, 67%-99%) and overall survival rate was 91% (95% CI, 79%-100%). Conclusions: Consolidation chemotherapy after CCRT is well tolerated and effective in patients with locally advanced cervical carcinoma. A prospective randomized trial to compare this treatment strategy with standard CCRT seems to be worthwhile

  2. Memory processes during sleep: beyond the standard consolidation theory.

    Science.gov (United States)

    Axmacher, Nikolai; Draguhn, Andreas; Elger, Christian E; Fell, Juergen

    2009-07-01

    Two-step theories of memory formation suggest that an initial encoding stage, during which transient neural assemblies are formed in the hippocampus, is followed by a second step called consolidation, which involves re-processing of activity patterns and is associated with an increasing involvement of the neocortex. Several studies in human subjects as well as in animals suggest that memory consolidation occurs predominantly during sleep (standard consolidation model). Alternatively, it has been suggested that consolidation may occur during waking state as well and that the role of sleep is rather to restore encoding capabilities of synaptic connections (synaptic downscaling theory). Here, we review the experimental evidence favoring and challenging these two views and suggest an integrative model of memory consolidation.

  3. Familiarity speeds up visual short-term memory consolidation.

    Science.gov (United States)

    Xie, Weizhen; Zhang, Weiwei

    2017-06-01

    Existing long-term memory (LTM) can boost the number of retained representations over a short delay in visual short-term memory (VSTM). However, it is unclear whether and how prior LTM affects the initial process of transforming fragile sensory inputs into durable VSTM representations (i.e., VSTM consolidation). The consolidation speed hypothesis predicts faster consolidation for familiar relative to unfamiliar stimuli. Alternatively, the perceptual boost hypothesis predicts that the advantage in perceptual processing of familiar stimuli should add a constant boost for familiar stimuli during VSTM consolidation. To test these competing hypotheses, the present study examined how the large variance in participants' prior multimedia experience with Pokémon affected VSTM for Pokémon. In Experiment 1, the amount of time allowed for VSTM consolidation was manipulated by presenting consolidation masks at different intervals after the onset of to-be-remembered Pokémon characters. First-generation Pokémon characters that participants were more familiar with were consolidated faster into VSTM as compared with recent-generation Pokémon characters that participants were less familiar with. These effects were absent in participants who were unfamiliar with both generations of Pokémon. Although familiarity also increased the number of retained Pokémon characters when consolidation was uninterrupted but still incomplete due to insufficient encoding time in Experiment 1, this capacity effect was absent in Experiment 2 when consolidation was allowed to complete with sufficient encoding time. Together, these results support the consolidation speed hypothesis over the perceptual boost hypothesis and highlight the importance of assessing experimental effects on both processing and representation aspects of VSTM. (PsycINFO Database Record (c) 2017 APA, all rights reserved).

  4. Methods of synthesizing thermoelectric materials

    Science.gov (United States)

    Ren, Zhifeng; Chen, Shuo; Liu, Wei-Shu; Wang, Hengzhi; Wang, Hui; Yu, Bo; Chen, Gang

    2016-04-05

    Methods for synthesis of thermoelectric materials are disclosed. In some embodiments, a method of fabricating a thermoelectric material includes generating a plurality of nanoparticles from a starting material comprising one or more chalcogens and one or more transition metals; and consolidating the nanoparticles under elevated pressure and temperature, wherein the nanoparticles are heated and cooled at a controlled rate.

  5. Patterns of failure following bone marrow transplantation for metastatic breast cancer: the role of consolidative local therapy

    International Nuclear Information System (INIS)

    Shah, Amit B.; Hartsell, William F.; Ghalie, Richard; Kaizer, Herbert

    1995-01-01

    Purpose: The purpose of this analysis is to evaluate the patterns of failure and the role of local therapy in conjunction with bone marrow transplantation (BMT) for metastatic or recurrent breast cancer. Methods and Materials: Between June 1986 and November 1991, 46 patients with hormone unresponsive metastatic or recurrent breast cancer underwent high dose chemotherapy (HDC) with hematopoietic stem cell support. The most commonly used preparative regimen consisted of thiotepa (750 mg/m 2 ), cisplatin (150 mg/m 2 ), and cyclophosphamide (120 mg/kg) followed by autologous BMT. Consolidative surgery or irradiation was considered in patients whose cancer responded to BMT and had localized sites of disease. Results: Six patients (13%) died of BMT-related complications. Of the remaining 40 patients, 22 were candidates for consolidative therapy, and 18 of those patients received consolidative irradiation (17 patients) or surgery (1 patient) to one or more sites. At median follow-up of 27 months (range, 20-78), 12 of 18 (67%) patients have continuous local control at the 22 consolidated sites (1 of 4 controlled at chest wall sites, 7 of 8 at regional nodal sites, 7 of 7 at localized bone sites, and 1 of 3 at lung/mediastinal sites). Toxicity of consolidative irradiation was mainly limited to myelosuppression in 6 of 17 patients. Two patients did not complete the consolidative local therapy, one because of hematologic toxicity and one because of rapid systemic tumor progression during treatment. Conclusion: In patients with localized areas of extravisceral metastases, consolidative irradiation is feasible with acceptable hematologic toxicity. Consolidative irradiation can result in continuous local control, especially in isolated bone metastases and in regional nodal sites; however, the advantage is less clear in patients undergoing consolidative irradiation for chest wall failures. Because distant visceral metastases still remain a major site of failure after this HDC

  6. 26 CFR 1.1502-21A - Consolidated net operating loss deduction generally applicable for consolidated return years...

    Science.gov (United States)

    2010-04-01

    ... operating loss attributable to such member. (iii) Foreign expropriation losses. An election under section... expropriation loss) may be made for a consolidated return year only if the sum of the foreign expropriation... expropriation losses, or (b) the consolidated net operating loss. (3) Absorption rules. For purposes of...

  7. 20 September 2013 - Ambassador Z. Akram , Permanent Representative of the Islamic Republic of Pakistan to the United Nations Office and other international organisations in Geneva (3rd) with Mechanical and Materials Engineering Group Leader F. Bertinelli, Head of International Relations R. Voss, CMS Collaboration, Quaid-i-Azam University H. Hoorani, Permanent Mission First Secretary U. Iqbal Jadoon and LHC Consolidation, Industrial Services, Technology Department JP. Tock in front of the lift to the LHC tunnel at Point 1. Site Manager M. Décombaz on the back.

    CERN Multimedia

    Anna Pantelia

    2013-01-01

    20 September 2013 - Ambassador Z. Akram , Permanent Representative of the Islamic Republic of Pakistan to the United Nations Office and other international organisations in Geneva (3rd) with Mechanical and Materials Engineering Group Leader F. Bertinelli, Head of International Relations R. Voss, CMS Collaboration, Quaid-i-Azam University H. Hoorani, Permanent Mission First Secretary U. Iqbal Jadoon and LHC Consolidation, Industrial Services, Technology Department JP. Tock in front of the lift to the LHC tunnel at Point 1. Site Manager M. Décombaz on the back.

  8. Mathematical model of consolidation of fine concrete mixtures with different mobility, casted by vacuumizing and axial pressing in layers

    Directory of Open Access Journals (Sweden)

    Dedeneva Elena

    2017-01-01

    Full Text Available A mathematical model allowing establishing regularities in the consolidation processes of fine-grained concrete mixtures with different mobility and compaction methods has been worked out. This study is based on two-phase systems and nonlinear character of their consolidation. It resolves the question of the choice of vacuumizing optimal parameters and axial pressing in layers for molding of thin-walled products such as concrete roof tiles and concrete pipe products. Finally, we can get products without heat treatment by the materials and energy-saving technologies.

  9. Effects of consolidation process on microstructure and mechanical properties of commingled glass/polypropylene composites

    International Nuclear Information System (INIS)

    Tufail, M.; Long, A.C.; Rudd, C.D.

    2001-01-01

    The thermal history of a thermoplastic composite material during forming and consolidation is critical to the quality of the component. Attempts to process outside the normal melt region will result in incomplete consolidation and voidage. Clearly then, the preheat phase plays a key role in successful processing. Too low a preheat temperature results in insufficient matrix flow while, if the temperature is increased too much, degradation of the matrix occurs, again resulting in poor quality of the composite. In particular polypropylene has poor chemical (oxidative) resistance, and oxidative degradation reduces the average molecular weight of the materials. If excessive, this can result in a dramatic reduction in mechanical properties. Flat plaques of braided, commingled glass/polypropylene yarn were produced to examine these effects using both isothermal and non-isothermal consolidation. Woven plaques were also produced from commingled yarn in a similar fashion as control samples in order to identify any effects specific to the braiding process. This paper describes the effect of heating and stamping cycles on the properties of these composites, concentrating on the effects of temperature, heating time and compaction rate. (author)

  10. Consolidation through the looking-glass: sleep-dependent proactive interference on visuomotor adaptation in children.

    Science.gov (United States)

    Urbain, Charline; Houyoux, Emeline; Albouy, Geneviève; Peigneux, Philippe

    2014-02-01

    Although a beneficial role of post-training sleep for declarative memory has been consistently evidenced in children, as in adults, available data suggest that procedural memory consolidation does not benefit from sleep in children. However, besides the absence of performance gains in children, sleep-dependent plasticity processes involved in procedural memory consolidation might be expressed through differential interference effects on the learning of novel but related procedural material. To test this hypothesis, 32 10-12-year-old children were trained on a motor rotation adaptation task. After either a sleep or a wake period, they were first retested on the same rotation applied at learning, thus assessing offline sleep-dependent changes in performance, then on the opposite (unlearned) rotation to assess sleep-dependent modulations in proactive interference coming from the consolidated visuomotor memory trace. Results show that children gradually improve performance over the learning session, showing effective adaptation to the imposed rotation. In line with previous findings, no sleep-dependent changes in performance were observed for the learned rotation. However, presentation of the opposite, unlearned deviation elicited significantly higher interference effects after post-training sleep than wakefulness in children. Considering that a definite feature of procedural motor memory and skill acquisition is the implementation of highly automatized motor behaviour, thus lacking flexibility, our results suggest a better integration and/or automation or motor adaptation skills after post-training sleep, eventually resulting in higher proactive interference effects on untrained material. © 2013 European Sleep Research Society.

  11. Delayed working memory consolidation during the attentional blink.

    Science.gov (United States)

    Vogel, Edward K; Luck, Steven J

    2002-12-01

    After the detection of a target (T1) in a rapid stream of visual stimuli, there is a period of 400-600 msec during which a subsequent target (T2) is missed. This impairment in performance has been labeled the attentional blink. Recent theories propose that the attentional blink reflects a bottleneck in working memory consolidation such that T2 cannot be consolidated until after T1 is consolidated, and T2 is therefore masked by subsequent stimuli if it is presented while T1 is being consolidated. In support of this explanation, Giesbrecht & Di Lollo (1998) found that when T2 is the final item in the stimulus stream, no attentional blink is observed, because there are no subsequent stimuli that might mask T2. To provide a direct test of this explanation of the attentional blink, in the present study we used the P3 component of the event-related potential waveform to track the processing of T2. When T2 was followed by a masking item, we found that the P3 wave was completely suppressed during the attentional blink period, indicating that T2 was not consolidated in working memory. When T2 was the last item in the stimulus stream, however, we found that the P3 wave was delayed but not suppressed, indicating that T2 consolidation was not eliminated but simply delayed. These results are consistent with a fundamental limit on the consolidation of information in working memory.

  12. Cost targets for at-reactor spent fuel rod consolidation

    International Nuclear Information System (INIS)

    Macnabb, W.V.

    1985-01-01

    The high-level nuclear waste management system in the US currently envisions the disposal of spent fuel rods that have been removed from their assemblies and reconfigured into closely packed arrays. The process of fuel rod removal and packaging, referred to as rod consolidation, can occur either at reactors or at an integrated packaging facility, monitored retrievable storage (MRS). Rod consolidation at reactors results in cost savings down stream of reactors by reducing needs for additional storage, reducing the number of shipments, and reducing (eliminating, in the extreme) the amount of fuel handling and consolidation at the MRS. These savings accrue to the nuclear waste fund. Although private industry is expected to pay for at-reactor activities, including rod consolidation, it is of interest to estimate cost savings to the waste system if all fuel were consolidated at reactors. If there are savings, the US Department of Energy (DOE) may find it advantageous to pay for at-reactor rod consolidation from the nuclear waste fund. This paper assesses and compares the costs of rod consolidation at reactors and at the MRS in order to determine at what levels the former could be cost competitive with the latter

  13. Dynamic Consolidation and Investigation of Nanostructural W-Cu / W-Y Cylindrical Billets

    Science.gov (United States)

    Godibadze, B.; Dgebuadze, A.; Chagelishvili, E.; Mamniashvili, G.; Peikrishvili, A.

    2018-03-01

    The main purpose of presented work is to obtain W-Cu & W-Y cylindrical bulk nanostructured billets by explosive consolidation technology (ECT) in hot condition, with low porosity near to theoretical densities and improved physical / mechanical properties. Nanocomposites were subjected to densification into cylindrical steel tube containers using hot explosive consolidation (HEC) technology to fabricate high dense cylindrical billets. The first stage : Preliminary explosive densification of the precursor powder blend is carried out at room temperature with a loading intensity up to 10GPa to increase the initial density and to activate the particle surfaces in the blend. The second stage investigation were carried out for the same already predensified billets, but consolidation were conducted in hot conditions, after heating of samples in between 940-11000C, the intensity of loading was equal to 10GPa. Consolidated different type of W-Cu composition containing 10-40% of nanoscale W, during investigation showed that the combination of high temperatures (above 940°C) and two-stage shock wave compression was beneficial to the consolidation of the incompatible pair W-Cu composites, resulting in high densities, good integrity and good electronic properties. The structure and property of the samples obtained, depended on the sizes of tungsten particles. It was established that in comparison with W-Cu composites with coarse tungsten the application of nanoscale W precursors and depending of content of W gives different result. Tungsten is a prime material candidate for the first wall of a future fusion reactor. In this study, the microstructure and microhardness of tungsten-yttrium (W-Y) composites were investigated as a function of Y doping content (0.5÷2 wt. %). It was found that the crystallite sizes and the powder particle sizes were increased as a result of the increase of Y content. Nearly fully dense materials were obtained for W-Y alloys when the Y content was

  14. Consolidation of cladding hulls from the electrometallurgical treatment of spent fuel

    International Nuclear Information System (INIS)

    Keiser, D.D. Jr.

    1998-01-01

    To consolidate metallic waste that is residual from Argonne National Laboratory's electrometallurgical treatment of spent nuclear fuel, waste ingots are currently being cast using an induction furnace located in a hot cell. These ingots, which have been developed to serve as final waste forms destined for repository disposal, are stainless steel (SS)-Zr alloys (the Zr is very near 15 wt.%). The charge for the alloys consists of stainless steel cladding hulls, Zr from the fuel being treated, noble metal fission products, and minor amounts of actinides that are present with the cladding hulls. The actual in-dated cladding hulls have been characterized before they were melted into ingots, and the final as-cast ingots have been characterized to determine the degree of consolidation of the charge material. It has been found that ingots can be effectively cast from irradiated cladding hulls residual from the electrometallurgical treatment process by employing an induction furnace located in a hot cell

  15. Chemical and Radiochemical Analysis of Consolidated Sludge Samples from the K East Basin

    International Nuclear Information System (INIS)

    Elmore, M.R.; Schmidt, A.J.; Silvers, K.L.; Thornton, B.M.

    2000-01-01

    This report describes results from analyses performed to characterize the consolidated sludge samples collected from the Hanford K East Basin in March and April 1999. The consolidated sludge samples were collected to provide additional material needed for the evaluation and design of systems that will be used to manage the K Basin sludge (i.e., disposition the sludge to T Plant for interim storage). The analytical results given in this report add to the knowledge on the composition of the K Basin sludge and provide specific information on this sludge necessary to plan and understand subsequent process testing. The following analyses were performed: weight percent (wt%) solids determination; uranium analysis by kinetic phosphorescence; plutonium isotope analysis by extraction chromatographic separation followed by alpha energy analysis (AEA); gross beta analysis; gamma energy analysis (GEA); and metals analysis by inductively coupled plasma atomic emission spectroscopy (ICP-AES)

  16. Feasibility demonstration of consolidating porous beryllium/carbon structures. Final report

    International Nuclear Information System (INIS)

    Browning, M.J.; Hoover, G.E.; Mueller, J.J.; Hanes, H.D.

    1977-01-01

    A preliminary feasibility study was initiated to determine if porous beryllium structures could be fabricated by consolidating beryllium-coated microballoons into a rigid structure. The target specifications were to coat nominally 1-mm diameter microspheres with 0.5-mil beryllium coatings and then bond into a structure. Because of the very short time period, it was agreeable to use existing or quickly-available materials. The general approach was to apply coatings to carbon or quartz microspheres. Physical vapor deposition and ''snow-balling'' of fine beryllium powder were the two methods investigated. Once the particles were coated, HIP (pressure bonding) and pressureless sintering were to be investigated as methods for consolidating the microballoons. A low level of effort was to be spent to look at means of fabricating an all-carbon structure

  17. Penetration of the consolidant Paraloid® B-72 in Macuxi indigenous ceramic vessels investigated by neutron tomography

    Science.gov (United States)

    Stanojev Pereira, Marco A.; Pugliesi, Reynaldo

    2018-05-01

    The neutron tomography technique was applied in studying the penetration of the consolidant Paraloid® B-72 in contemporary indigenous ceramic vessels. The study was carried out for two distinct and controlled air humidity conditions, 40% and 90%, in which the vessels were exposed, before the consolidant application. The obtained images have proved that the penetration of Paraloid® B-72 in the ceramic does not depend on the humidity condition in which it was applied, moreover allowed a macro-visualization of the consolidant penetration in the ceramic vessel. As the vessels used in the present work were manufactured by an indigenous artisan, Macuxi, according to the same procedures and raw materials used by the ancient artisans, the results obtained can be used as a guide to assist experts, both in the study of archeological objects of Macuxi origin, as well as other objects that had been made by other tribes that lived in the same Amazon region, in Brazil.

  18. COST IMPACT OF ROD CONSOLIDATION ON THE VIABILITY ASSESSMENT DESIGN

    International Nuclear Information System (INIS)

    D. Lancaster

    1999-01-01

    The cost impact to the Civilian Radioactive Waste Management System of using rod consolidation is evaluated. Previous work has demonstrated that the fuel rods of two assemblies can be packed into a canister that can fit into the same size space as that used to store a single assembly. The remaining fuel assembly hardware can be compacted into the same size canisters with a ratio of 1 hardware canister per each 6 to 12 assemblies. Transportation casks of the same size as currently available can load twice the number of assemblies by placing the compacted assemblies in the slots currently designed for a single assembly. Waste packages similarly could contain twice the number of assemblies; however, thermal constraints would require considering either a low burnup or cooling. The analysis evaluates the impact of rod consolidation on CRWMS costs for consolidation at prior to transportation and for consolidation at the Monitored Geological Repository surface facility. For this study, no design changes were made to either the transport casks or waste packages. Waste package designs used for the Viability Assessment design were employed but derated to make the thermal limits. A logistics analysis of the waste was performed to determine the number of each waste package with each loading. A review of past rod consolidation experience found cost estimates which range from $10/kgU to $32/kgU. $30/kgU was assumed for rod consolidation costs prior to transportation. Transportation cost savings are about $17/kgU and waste package cost savings are about $21/kgU. The net saving to the system is approximately $500 million if the consolidation is performed prior to transportation. If consolidation were performed at the repository surface facilities, it would cost approximately $15/kgU. No transportation savings would be realized. The net savings for consolidation at the repository site would be about $400 million dollars

  19. 7 CFR 4290.470 - Prior approval of merger, consolidation, or reorganization of RBIC.

    Science.gov (United States)

    2010-01-01

    ... merge, consolidate, change form of organization (corporation, limited liability company, or limited partnership) or reorganize without the Secretary's prior written approval. Any such merger, consolidation, or...

  20. Consolidated Edison Company of New York, Inc

    International Nuclear Information System (INIS)

    Raebiger, R.F.; King, R.D.; Friess, R.A.

    1992-01-01

    This paper reports that in 1989 Consolidated Edison Company of New York which initiated a comprehensive tank cleaning and inspection program of their petroleum distillate storage facilities. The program was initiated by the issuance of new regulations of the New York State Department of Environmental Conservation. A total of 10 storage tanks were cleaned, inspected and detailed engineering reports prepared for each storage tank. A total of 28 distillate storage facilities will be inspected over a three year period of time. The tanks ranged in size from 18,000 to 2,701,00 gallons and contained either No. 2 Fuel Oil or Kerosene. The project included waste disposal, tank cleaning, inspection, engineering evaluations and the design of tank repairs. Of the 10 tanks inspected, three of the tanks required extensive repairs including the design and installation of a new bottom shell course and partial floor replacement for one of the tanks. The project was completed on schedule and within the budget allocated. The ten tank project was evaluated upon its completion and recommendations regarding tank operations and maintenance were provided to minimize maintenance problems for the future

  1. Acute exercise and motor memory consolidation

    DEFF Research Database (Denmark)

    Thomas, Richard; Beck, Mikkel Malling; Lind, Rune Rasmussen

    2016-01-01

    High intensity aerobic exercise amplifies offline gains in procedural memory acquired during motor practice. This effect seems to be evident when exercise is placed immediately after acquisition, during the first stages of memory consolidation, but the importance of temporal proximity...... of the exercise bout used to stimulate improvements in procedural memory is unknown. The effects of three different temporal placements of high intensity exercise were investigated following visuomotor skill acquisition on the retention of motor memory in 48 young (24.0 ± 2.5 yrs), healthy male subjects randomly...... assigned to one of four groups either performing a high intensity (90% Maximal Power Output) exercise bout at 20 min (EX90), 1 h (EX90+1), 2 h (EX90+2) after acquisition or rested (CON). Retention tests were performed at 1 d (R1) and 7 d (R7). At R1 changes in performance scores after acquisition were...

  2. Automation, consolidation, and integration in autoimmune diagnostics.

    Science.gov (United States)

    Tozzoli, Renato; D'Aurizio, Federica; Villalta, Danilo; Bizzaro, Nicola

    2015-08-01

    Over the past two decades, we have witnessed an extraordinary change in autoimmune diagnostics, characterized by the progressive evolution of analytical technologies, the availability of new tests, and the explosive growth of molecular biology and proteomics. Aside from these huge improvements, organizational changes have also occurred which brought about a more modern vision of the autoimmune laboratory. The introduction of automation (for harmonization of testing, reduction of human error, reduction of handling steps, increase of productivity, decrease of turnaround time, improvement of safety), consolidation (combining different analytical technologies or strategies on one instrument or on one group of connected instruments) and integration (linking analytical instruments or group of instruments with pre- and post-analytical devices) opened a new era in immunodiagnostics. In this article, we review the most important changes that have occurred in autoimmune diagnostics and present some models related to the introduction of automation in the autoimmunology laboratory, such as automated indirect immunofluorescence and changes in the two-step strategy for detection of autoantibodies; automated monoplex immunoassays and reduction of turnaround time; and automated multiplex immunoassays for autoantibody profiling.

  3. SOME ASPECTS REGARDING THE THEORIES OF CONSOLIDATED FINANCIAL STATEMENTS

    OpenAIRE

    Carmen NISTOR

    2015-01-01

    Although accounts consolidation was used in practice from the early 1900’s its theoretical basis were developed later in concordance with the rise of concepts like “entity” and “group”. The aim of this article is to examine the literature in the accounting field regarding the consolidation theories developed over the years. In order to discuss the different opinions regarding the consolidation theories we used the descriptive approach. As a result we tried to explain how these theories appear...

  4. A cold demonstration of fuel consolidation. Part 1

    International Nuclear Information System (INIS)

    Matheson, J.E.

    1989-01-01

    Spent fuel consolidation is an option for increasing spent fuel storage capacities being considered by many utilities. The process of consolidating fuel involves separating the fuel rods from the structural frame which holds them in a square array. The rods are then repackaged into a tightly packed bundle which occupies about half the cross-sectional area of fuel assembly. Thus approximately twice as much fuel can be stored in the underwater racks at a spent fuel storage pool. There have been several demonstrations of fuel consolidation to date. The focus of this paper is the development and subsequent demonstration program of a shear/compactor

  5. Higher-performance beryllium materials for aerospace and defense applications

    International Nuclear Information System (INIS)

    Parsonage, T.B.

    1991-01-01

    A new plant has been tooled for the production of near-net-shape blanks for Be structural components, using both HIP and cold isostatic pressing to consolidate Be powders. Attention is given to blanks for integrally honeycomb-reinforced lightweight mirrors. HIPed materials' ultimate tensile strength is superior to that of vacuum hot-pressed material, due to the finer grain sizes obtainable via P/M powder consolidation, lower consolidation temperatures, and shorter processing cycle. The use of spherical Be powders allows higher packing density than for impact-ground powders, resulting in reduced shrinkage upon consolidation

  6. Variation of properties of clayey minerals and associated phases about uranium deposits related to proterozoic discordances; Variation des proprietes des mineraux argileux et des phases associees autour des gisements d'uranium lies aux discordances Proterozoiques

    Energy Technology Data Exchange (ETDEWEB)

    Beaufort, D.; Patrier, P.; Laverret, E.; Gaboreau, St.; Billault, V. [HYDRASA, Universite de Poitiers-CNRS, 86 - Poitiers (France); Quirt, D. [AREVA Resources Canada AREVA Resources Canada Inc., Saskatoon, SK (Canada)

    2009-07-01

    The authors propose explanations for the clayey alteration which surrounds uranium deposits related to proterozoic discordances as it is noticed in Canada (Athabasca) and Australia (Kombolgie). The observed mineral sequences are interpreted as the product of an increasing interaction between infiltrated diagenetic acid and oxidising solutions on the one hand, and platform rocks on the other hand, at temperatures between 150 and 200 C. These interpretations are based on crystallographic and crystallochemical investigations

  7. Correlation of clayey gouge in a surface exposure of serpentinite in the San Andreas Fault with gouge from the San Andreas Fault Observatory at Depth (SAFOD)

    Science.gov (United States)

    Moore, Diane E.; Rymer, Michael J.

    2012-05-01

    Magnesium-rich clayey gouge similar to that comprising the two actively creeping strands of the San Andreas Fault in drill core from the San Andreas Fault Observatory at Depth (SAFOD) has been identified in a nearby outcrop of serpentinite within the fault zone at Nelson Creek. Each occurrence of the gouge consists of porphyroclasts of serpentinite and sedimentary rocks dispersed in a fine-grained, foliated matrix of Mg-rich smectitic clays. The clay minerals in all three gouges are interpreted to be the product of fluid-assisted, shear-enhanced reactions between quartzofeldspathic wall rocks and serpentinite that was tectonically entrained in the fault from a source in the Coast Range Ophiolite. We infer that the gouge at Nelson Creek connects to one or both of the gouge zones in the SAFOD core, and that similar gouge may occur at depths in between. The special significance of the outcrop is that it preserves the early stages of mineral reactions that are greatly advanced at depth, and it confirms the involvement of serpentinite and the Mg-rich phyllosilicate minerals that replace it in promoting creep along the central San Andreas Fault.

  8. Correlation of clayey gouge in a surface exposure of the San Andreas fault with gouge at depth from SAFOD: Implications for the role of serpentinite in fault mechanics

    Science.gov (United States)

    Moore, Diane E.; Rymer, Michael J.

    2012-01-01

    Magnesium-rich clayey gouge similar to that comprising the two actively creeping strands of the San Andreas Fault in drill core from the San Andreas Fault Observatory at Depth (SAFOD) has been identified in a nearby outcrop of serpentinite within the fault zone at Nelson Creek. Each occurrence of the gouge consists of porphyroclasts of serpentinite and sedimentary rocks dispersed in a fine-grained, foliated matrix of Mg-rich smectitic clays. The clay minerals in all three gouges are interpreted to be the product of fluid-assisted, shear-enhanced reactions between quartzofeldspathic wall rocks and serpentinite that was tectonically entrained in the fault from a source in the Coast Range Ophiolite. We infer that the gouge at Nelson Creek connects to one or both of the gouge zones in the SAFOD core, and that similar gouge may occur at depths in between. The special significance of the outcrop is that it preserves the early stages of mineral reactions that are greatly advanced at depth, and it confirms the involvement of serpentinite and the Mg-rich phyllosilicate minerals that replace it in promoting creep along the central San Andreas Fault.

  9. Adsorption of a textile dye "Indanthrene Blue RS (C.I. Vat Blue 4)" from aqueous solutions onto smectite-rich clayey rock.

    Science.gov (United States)

    Chaari, Islem; Feki, Mongi; Medhioub, Mounir; Bouzid, Jalel; Fakhfakh, Emna; Jamoussi, Fakher

    2009-12-30

    The adsorption of a textile dye, namely, Indanthrene Blue RS (C.I. Vat Blue 4) onto smectite-rich clayey rock (AYD) and its sulphuric acid-activated products (AYDS) in aqueous solution was studied in a batch system with respect to contact time, pH, and temperature. The adsorbents employed were characterized by X-ray diffraction, infrared spectroscopy and specific surface area, cation exchange capacity and point of zero charge were also estimated. The effect of contact time on dye adsorption showed that the equilibrium was reached after a contact time of 40 min for the both adsorbents. The optimum pH for dye retention was found 6.0 for AYDS and 7.3 for AYD. The equilibrium adsorption data were analysed using the Langmuir and Freundlich isotherms. The adsorption capacities (Q(m)) for AYD and AYDS were found 13.92 mg/g and 17.85 mg/g, respectively. The effect of temperature on the adsorption was also investigated; adsorption of Indanthrene Blue RS is an endothermic process. This study demonstrates that all the considered adsorbents can be used as an alternative emerging technology for water treatment.

  10. Consolidation of municipalities in the newest time

    Directory of Open Access Journals (Sweden)

    Yury Blagov

    2017-01-01

    of some RF constituent entities, there are urban districts that consist of the large not urbanized territories with a poorly developed transport, social, economic infrastructure and without any common development goals. The authors conclude that the bias towards municipalities' consolidation in many RF constituent entities is justified and caused by ignoring of the vertical command relations in former areas. At the same time, they point out the need to take into account the town-planning, economic and geographical, socio-demographic factors while transforming municipal areas into urban districts, otherwise, all these transformations are fictitious and turn into revising of powers by local elites.Conclusions. The municipal legal policy of consolidation of municipal entities is aimed at liquidating the settlement level of local self-government, which directly contradicts Part 1 of Art. 131 of the Constitution of the Russian Federation, which establishes the implementation of local self-government by the population, first of all, at the primary, settlement level. 

  11. UbuntuNet Alliance : Consolidating Research and Education ...

    International Development Research Centre (IDRC) Digital Library (Canada)

    UbuntuNet Alliance : Consolidating Research and Education Networking - Phase II ... North of Sahara, South of Sahara, United States ... social science, population and public health, and health systems research relevant to the emerging crisis.

  12. Thermal Consolidation of Dredge Sand for Artificial Reef Formations

    Science.gov (United States)

    Trevino, Alexandro

    Coral Reef ecosystems have degraded over years due to a variety of environmental issues such as ocean acidification. The continuous stress has detrimental effects on coral reef ecosystems that can possibly lead to the loss of the ecosystem. Our research aims to construct a prototype of an artificial reef by consolidating dredge sand from the ship channels of South Texas. Consolidation is achieved through an aluminum polytetrafluoroethylene self-propagating high temperature process that yields a solid formation to mimic the physical properties of coral reef structures. Using thermodynamic calculations, the variation of initial components was determined that reached an adiabatic temperature with a maximum peak of 2000 K. The self-sustaining reaction front was obtained to rigidly consolidate the dredge sand only at composition concentrations exceeding a critical value of 24 wt.% Al, and 3 wt.% PTFE. The combustion synthesis produced a consolidated formation with a hardened and porous structure.

  13. textural dependence of shear strength and consolidation of colliery

    African Journals Online (AJOL)

    eobe

    for their use were based on the properties of a wide range of .... Fig. 1 shows the grain size distribution curves of the mine wastes. Each ... wholly above the ground water level while sulphate .... consolidation curve assumes the usual shape.

  14. Strategic Framework for the Defense Acquisition System Understanding Defense Consolidation

    National Research Council Canada - National Science Library

    Potts, Anthony W

    2007-01-01

    The 1993 policy to promote the consolidation of the United States defense industry began a series of acquisitions and mergers that went beyond the intent of the policy and left the Department of Defense (DoD...

  15. Analysis of Defense Industry Consolidation Effects on Program Acquisition Costs

    National Research Council Canada - National Science Library

    Hoff, Russell V

    2007-01-01

    .... This thesis examines whether cost changes are evident following consolidation within the defense industry by conducting a regression analysis of Major Defense Acquisition Programs across 13 broad defense market sectors...

  16. Challenges of the banking consolidation in Nigeria | Oyefeso ...

    African Journals Online (AJOL)

    CBN) and the new mega banks may face as a consequence of the banking consolidation reforms in Nigeria. Surmounting these challenges will require CBN's commitment to implementing the Basel II directives and instituting adequate Act of ...

  17. #DDOD Use Case: Consolidated reporting of medical device recalls

    Data.gov (United States)

    U.S. Department of Health & Human Services — SUMMARY DDOD use case request for consolidated, consistent reporting of medical device recalls. WHAT IS A USE CASE? A “Use Case” is a request that was made by the...

  18. A thermomechanical crystal plasticity constitutive model for ultrasonic consolidation

    KAUST Repository

    Siddiq, Amir; El Sayed, Tamer S.

    2012-01-01

    We present a micromechanics-based thermomechanical constitutive model to simulate the ultrasonic consolidation process. Model parameters are calibrated using an inverse modeling approach. A comparison of the simulated response and experimental

  19. Better than sleep: theta neurofeedback training accelerates memory consolidation.

    Science.gov (United States)

    Reiner, Miriam; Rozengurt, Roman; Barnea, Anat

    2014-01-01

    Consistent empirical results showed that both night and day sleep enhanced memory consolidation. In this study we explore processes of consolidation of memory during awake hours. Since theta oscillations have been shown to play a central role in exchange of information, we hypothesized that elevated theta during awake hours will enhance memory consolidation. We used a neurofeedback protocol, to enhance the relative power of theta or beta oscillations. Participants trained on a tapping task, were divided into three groups: neurofeedback theta; neurofeedback beta; control. We found a significant improvement in performance in the theta group, relative to the beta and control groups, immediately after neurofeedback. Performance was further improved after night sleep in all groups, with a significant advantage favoring the theta group. Theta power during training was correlated with the level of improvement, indicating a clear relationship between memory consolidation, and theta neurofeedback. Copyright © 2013 Elsevier B.V. All rights reserved.

  20. 7 CFR 1735.19 - Mergers and consolidations.

    Science.gov (United States)

    2010-01-01

    ... Basic Policies § 1735.19 Mergers and consolidations. RUS does not make loans for the sole purpose of... making loans to the telephone system to finance the improvement or extension of telephone service in...

  1. The Military As A Hindrance In Mexico's Consolidation Of Democracy

    National Research Council Canada - National Science Library

    Villarreal, Sergio

    2001-01-01

    The argument in this thesis is that the Mexican military stands as a hindrance in Mexico's consolidation because of the lack of executive and legislative controls over the armed forces, and military prerogatives...

  2. Role of adult neurogenesis in hippocampal-cortical memory consolidation

    Science.gov (United States)

    2014-01-01

    Acquired memory is initially dependent on the hippocampus (HPC) for permanent memory formation. This hippocampal dependency of memory recall progressively decays with time, a process that is associated with a gradual increase in dependency upon cortical structures. This process is commonly referred to as systems consolidation theory. In this paper, we first review how memory becomes hippocampal dependent to cortical dependent with an emphasis on the interactions that occur between the HPC and cortex during systems consolidation. We also review the mechanisms underlying the gradual decay of HPC dependency during systems consolidation from the perspective of memory erasures by adult hippocampal neurogenesis. Finally, we discuss the relationship between systems consolidation and memory precision. PMID:24552281

  3. ER Consolidated Qtrly Rpt_April-June 2016_October 2016

    Energy Technology Data Exchange (ETDEWEB)

    Cochran, John R. [Sandia National Lab. (SNL-NM), Albuquerque, NM (United States)

    2016-10-01

    This Environmental Restoration Operations (ER) Consolidated Quarterly Report (ER Quarterly Report) provides the status of ongoing corrective action activities being implemented by Sandia National Laboratories, New Mexico (SNL/NM) for the April, May, and June 2016 quarterly reporting period.

  4. CONSOLIDATED FINANCIAL STATEMENTS IN UKRAINE: NORMATIVE AND LEGAL REGULATION STATE

    Directory of Open Access Journals (Sweden)

    S.V. Kucher

    2016-09-01

    Full Text Available The development of big business in Ukraine has led to the need to release a number of domestic companies and their groups and associations to the international financial market which was the prerequisite of the needs of users of financial statements to obtain reliable information about the activities of such companies. In accordance with the national legislation associations of enterprises and companies have to provide the consolidated financial statements which contain the pooled indices about the activities of these entities. The article analyzes the current state of normative and legal regulation of financial reporting consolidation process in Ukraine. In particular, the paper determines the basic legal acts of regulations of national and international governing process of preparation of consolidated financial statements; it also determines the circle of business entities required to draw up the consolidated financial statements solely in accordance with international financial reporting standards.

  5. Indigenous information as tool for consolidating and promoting ...

    African Journals Online (AJOL)

    Indigenous information as tool for consolidating and promoting natural ... Open Access DOWNLOAD FULL TEXT ... Specifically, local authority was the source of information rivers/streams (63.2%) and arable lands (56.0%) conservation.

  6. Strategic Framework for the Defense Acquisition System Understanding Defense Consolidation

    National Research Council Canada - National Science Library

    Potts, Anthony W

    2007-01-01

    ...% of defense product sales annually. Defense consolidation has diminished the flexibility required for surge capacity, diminished competitive innovations in products, and reduced competitive pricing based on multiple sources for products...

  7. Performance of self-consolidating concrete in prestressed girders.

    Science.gov (United States)

    2010-04-01

    A structural investigation of self-consolidating concrete (SCC) in AASHTO Type I precast, : prestressed girders was performed. Six test girders were subjected to transfer length and : flexural testing. Three separate concrete mixtures, two girders pe...

  8. Self-Consolidating Concrete for Prestressed Bridge Girders : Research Brief

    Science.gov (United States)

    2017-08-01

    Self-consolidating concrete (SCC) is commonly used as an alternative to conventional concrete (CC) in precast, prestressed concrete (PSC) bridge girders. The high strength, highly workable mixture can flow through dense reinforcement to fill formwork...

  9. Mesopontine median raphe regulates hippocampal ripple oscillation and memory consolidation.

    Science.gov (United States)

    Wang, Dong V; Yau, Hau-Jie; Broker, Carl J; Tsou, Jen-Hui; Bonci, Antonello; Ikemoto, Satoshi

    2015-05-01

    Sharp wave-associated field oscillations (∼200 Hz) of the hippocampus, referred to as ripples, are believed to be important for consolidation of explicit memory. Little is known about how ripples are regulated by other brain regions. We found that the median raphe region (MnR) is important for regulating hippocampal ripple activity and memory consolidation. We performed in vivo simultaneous recording in the MnR and hippocampus of mice and found that, when a group of MnR neurons was active, ripples were absent. Consistently, optogenetic stimulation of MnR neurons suppressed ripple activity and inhibition of these neurons increased ripple activity. Notably, using a fear conditioning procedure, we found that photostimulation of MnR neurons interfered with memory consolidation. Our results demonstrate a critical role of the MnR in regulating ripples and memory consolidation.

  10. The Savannah River Plant Consolidated Incineration Facility

    International Nuclear Information System (INIS)

    Weber, D.A.

    1987-01-01

    A full scale incinerator is proposed for construction at the Savannah River Plant (SRP) beginning in August 1989 for detoxifiction and volume reduction of liquid and solid low-level radioactive, mixed and RCRA hazardous waste. Wastes to be burned include drummed liquids, sludges and solids, liquid process wastes, and low-level boxed job control waste. The facility will consist of a rotary kiln primary combustion chamber followed by a tangentially fired cylindrical secondary combustion chamber (SCC) and be designed to process up to 12 tons per day of solid and liquid waste. Solid waste packaged in combustible containers will be fed to the rotary kiln incinerator using a ram feed system and liquid wastes will be introduced to the rotary kiln through a burner nozzle. Liquid waste will also be fed through a high intensity vortex burner in the SCC. Combustion gases will exit the SCC and be cooled to saturation in a spray quench. Particulate and acid gas are removed in a free jet scrubber. The off-gas will then pass through a cyclone separator, mist eliminator, reheater high efficiency particulate air (HEPA) filtration and induced draft blowers before release to the atmosphere. Incinerator ash and scrubber blowdown will be immobilized in a cement matrix and disposed of in an onsite RCRA permitted facility. The Consolidated Incineration Facility (CIF) will provide detoxification and volume reduction for up to 560,000 CUFT/yr of solid waste and up to 35,700 CUFT/yr of liquid waste. Up to 50,500 CUFT/yr of cement stabilized ash and blowdown will beproduced for an average overall volume reduction fator of 22:1. 3 figs., 2 tabs

  11. Preliminary Laser Cleaning Studies of a Consolidated Prehistoric Basketry Coming from the Pile Building of Fiave-Carera in the North-East of Italy

    International Nuclear Information System (INIS)

    Belli, R.; Miotello, A.; Mosaner, P.; Toniutti, L.; Bazzanella, M.

    2006-01-01

    In the archaeological field, some specific advantages are recognized to laser cleaning, like, for example, the absence of mechanical contacts with the sample. The cleaning procedures generally involve a multilayer structure (dust, dirty, organic deposits, and, in some cases, consolidant substances). In this work, prehistoric wood samples (found and consolidated in 1970s) have been laser irradiated (KrF excimer laser) in order to restore their original surface aspect. A certain amount of burned matter was also present. Samples came from a fragment of a prehistoric basketry found in the lake dwelling site of Fiave-Carera, Trento, Italy (1500-1400 BC). It was observed that the laser cleaning effects are strictly dependent on the irradiation parameters (power density and number of pulses). Efficient material removal was possible by using appropriate energy density. Moreover, for lower laser energy density, special structures appeared on the surface of the consolidating substance that we attributed to heating-induced stresses on the consolidant surface.

  12. A dynamic analysis of consolidation in the broadcast television industry

    OpenAIRE

    Jessica C. Stahl

    2009-01-01

    This paper estimates a dynamic oligopoly model in order to separately identify the demand-side and cost-side advantages of consolidation in the broadcast television industry. I exploit an exogenous change in regulation that led to significant industry consolidation. Using revenue and ownership data for broadcast stations over the past ten years, I estimate the effect of ownership changes on revenue. I recover costs by examining patterns in ownership changes that are left unexplained by revenu...

  13. Hospital consolidation outlook: surviving in a tough economy.

    Science.gov (United States)

    Myers, Chris; Lineen, Jason

    2009-11-01

    The rapid hospital consolidation activity of the late 1990s has tapered off, but it's expected to pick up again. The reasons for hospital consolidation have shifted from gaining leverage with payers to achieving cost savings and operating efficiencies to survive in the market. The hospital industry can expect to undergo more profound structural and organizational changes in the decade ahead than it did in the past decade.

  14. Consolidated techniques for groups of enterprises with complex structure

    Directory of Open Access Journals (Sweden)

    Cristina Ciuraru-Andrica

    2009-12-01

    Full Text Available The preparation and disclosure of the financial statements of a group of enterprises involves some consolidation techniques. The Literature presents many techniques, but in practice are used two of them. They will be described first of all in a particular manner and after that in a comparative one. The group of entities can choose one of these techniques, the final result (the consolidated financial statements being the same, whatever the option.

  15. Consolidation by Prefabricated Vertical Drains with a Threshold Gradient

    OpenAIRE

    Xiao Guo; Kang-He Xie; Yue-Bao Deng

    2014-01-01

    This paper shows the development of an approximate analytical solution of radial consolidation by prefabricated vertical drains with a threshold gradient. To understand the effect of the threshold gradient on consolidation, a parametric analysis was performed using the present solution. The applicability of the present solution was demonstrated in two cases, wherein the comparisons with Hansbo’s results and observed data were conducted. It was found that (1) the flow with the threshold gradie...

  16. Consolidation in World Steel Industry - Implications for Poland

    OpenAIRE

    Beata Ślusarczyk

    2009-01-01

    Consolidation of enterprises has intensified with the growth of global competition. In the nineties of the past century, these processes became a conventional way for market expansion, leading to establishment of huge international companies with biggest influence on world economy. In steel industry, processes of consolidation have also been the leading processes in management, particularly during a time of prosperity for steel products that have taken place in recent years. The global consol...

  17. Retrieval as a Fast Route to Memory Consolidation.

    Science.gov (United States)

    Antony, James W; Ferreira, Catarina S; Norman, Kenneth A; Wimber, Maria

    2017-08-01

    Retrieval-mediated learning is a powerful way to make memories last, but its neurocognitive mechanisms remain unclear. We propose that retrieval acts as a rapid consolidation event, supporting the creation of adaptive hippocampal-neocortical representations via the 'online' reactivation of associative information. We describe parallels between online retrieval and offline consolidation and offer testable predictions for future research. Copyright © 2017 Elsevier Ltd. All rights reserved.

  18. Consolidation and restoration of memory traces in working memory.

    Science.gov (United States)

    De Schrijver, Sébastien; Barrouillet, Pierre

    2017-10-01

    Consolidation is the process through which ephemeral sensory traces are transformed into more stable short-term memory traces. It has been shown that consolidation plays a crucial role in working memory (WM) performance, by strengthening memory traces that then better resist interference and decay. In a recent study, Bayliss, Bogdanovs, and Jarrold (Journal of Memory and Language, 81, 34-50, 2015) argued that this process is separate from the processes known to restore WM traces after degradation, such as attentional refreshing and verbal rehearsal. In the present study, we investigated the relationship between the two types of processes in the context of WM span tasks. Participants were presented with series of letters for serial recall, each letter being followed by four digits for parity judgment. Consolidation opportunity was manipulated by varying the delay between each letter and the first digit to be processed, while opportunities for restoration were manipulated by varying the pace at which the parity task had to be performed (i.e., its cognitive load, or CL). Increasing the time available for either consolidation or restoration resulted in higher WM spans, with some substitutability between the two processes. Accordingly, when consolidation time was added to restoration time in the calculation of CL, the new resulting index, called extended CL, proved a very good predictor of recall performance, a finding also observed when verbal rehearsal was prevented by articulatory suppression. This substitutability between consolidation and restoration suggests that both processes may rely on the same mechanisms.

  19. Land consolidation in mountain areas. Case study from southern Poland

    Science.gov (United States)

    Janus, Jarosław; Łopacka, Magdalena; John, Ewa

    2017-12-01

    Land consolidation procedures are an attempt to comprehensively change the existing spatial structure of land in rural areas. This treatment also brings many other social and economic benefi ts, contributing to the development of consolidated areas. Land consolidation in mountain areas differs in many respects from those implemented in areas with more favorable conditions for the functioning of agriculture. The unfavorable values of land fragmentation indices, terrain conditions and lower than the average soil quality affect both the dominant forms of agricultural activity and the limited opportunities to improve the distribution of plots in space, parameters of shape, and the area as a result of land consolidation. For this reason, the effectiveness of land consolidation in mountain areas can be achieved by improving the quality of transportation network and the accessibility of the plots, arranging ownership issues and improving the quality of cadastral documentation. This article presents the evaluation of the measures of effectiveness of land consolidation realized in mountain areas on the example of Łetownia Village in the Małopolska Province, located in the southern part of Poland. Selected village is an area with unfavorable conditions for the functioning of agriculture and high values of land fragmentation indices.

  20. Land consolidation in mountain areas. Case study from southern Poland

    Directory of Open Access Journals (Sweden)

    Janus Jarosław

    2017-12-01

    Full Text Available Land consolidation procedures are an attempt to comprehensively change the existing spatial structure of land in rural areas. This treatment also brings many other social and economic benefi ts, contributing to the development of consolidated areas. Land consolidation in mountain areas differs in many respects from those implemented in areas with more favorable conditions for the functioning of agriculture. The unfavorable values of land fragmentation indices, terrain conditions and lower than the average soil quality affect both the dominant forms of agricultural activity and the limited opportunities to improve the distribution of plots in space, parameters of shape, and the area as a result of land consolidation. For this reason, the effectiveness of land consolidation in mountain areas can be achieved by improving the quality of transportation network and the accessibility of the plots, arranging ownership issues and improving the quality of cadastral documentation. This article presents the evaluation of the measures of effectiveness of land consolidation realized in mountain areas on the example of Łetownia Village in the Małopolska Province, located in the southern part of Poland. Selected village is an area with unfavorable conditions for the functioning of agriculture and high values of land fragmentation indices.

  1. Does abnormal sleep impair memory consolidation in schizophrenia?

    Directory of Open Access Journals (Sweden)

    Dara S Manoach

    2009-09-01

    Full Text Available Although disturbed sleep is a prominent feature of schizophrenia, its relation to the pathophysiology, signs, and symptoms of schizophrenia remains poorly understood. Sleep disturbances are well known to impair cognition in healthy individuals. Yet, in spite of its ubiquity in schizophrenia, abnormal sleep has generally been overlooked as a potential contributor to cognitive deficits. Amelioration of cognitive deficits is a current priority of the schizophrenia research community, but most efforts to define, characterize, and quantify cognitive deficits focus on cross-sectional measures. While this approach provides a valid snapshot of function, there is now overwhelming evidence that critical aspects of learning and memory consolidation happen offline, both over time and with sleep. Initial memory encoding is followed by a prolonged period of consolidation, integration, and reorganization, that continues over days or even years. Much of this evolution of memories is mediated by sleep. This article briefly reviews (i abnormal sleep in schizophrenia, (ii sleep-dependent memory consolidation in healthy individuals, (iii recent findings of impaired sleep-dependent memory consolidation in schizophrenia, and (iv implications of impaired sleep-dependent memory consolidation in schizophrenia. This literature suggests that abnormal sleep in schizophrenia disrupts attention and impairs sleep-dependent memory consolidation and task automation. We conclude that these sleep-dependent impairments may contribute substantially to generalized cognitive deficits in schizophrenia. Understanding this contribution may open new avenues to ameliorating cognitive dysfunction and thereby improve outcome in schizophrenia.

  2. Sleep-related memory consolidation in primary insomnia.

    Science.gov (United States)

    Nissen, Christoph; Kloepfer, Corinna; Feige, Bernd; Piosczyk, Hannah; Spiegelhalder, Kai; Voderholzer, Ulrich; Riemann, Dieter

    2011-03-01

    It has been suggested that healthy sleep facilitates the consolidation of newly acquired memories and underlying brain plasticity. The authors tested the hypothesis that patients with primary insomnia (PI) would show deficits in sleep-related memory consolidation compared to good sleeper controls (GSC). The study used a four-group parallel design (n=86) to investigate the effects of 12 h of night-time, including polysomnographically monitored sleep ('sleep condition' in PI and GSC), versus 12 h of daytime wakefulness ('wake condition' in PI and GSC) on procedural (mirror tracing task) and declarative memory consolidation (visual and verbal learning task). Demographic characteristics and memory encoding did not differ between the groups at baseline. Polysomnography revealed a significantly disturbed sleep profile in PI compared to GSC in the sleep condition. Night-time periods including sleep in GSC were associated with (i) a significantly enhanced procedural and declarative verbal memory consolidation compared to equal periods of daytime wakefulness in GSC and (ii) a significantly enhanced procedural memory consolidation compared to equal periods of daytime wakefulness and night-time sleep in PI. Across retention intervals of daytime wakefulness, no differences between the experimental groups were observed. This pattern of results suggests that healthy sleep fosters the consolidation of new memories, and that this process is impaired for procedural memories in patients with PI. Future work is needed to investigate the impact of treatment on improving sleep and memory. © 2010 European Sleep Research Society.

  3. Usage of internal statements in making consolidated financial statement

    Directory of Open Access Journals (Sweden)

    V.N. Herman

    2016-12-01

    Full Text Available The emergence of the consolidated financial statements is the result of integration processes in the businesses that lead to pooling of different companies. As consolidated financial statements present an aggregated look at the financial position of a parent and its subsidiaries, they let you gauge the overall health of an entire group of companies as opposed to one company’s standalone position. Consolidation of financial statements requires from the participants of joining elaborating their individual statements. The article describes the general scheme of consolidation process and defines the key trends of consolidation adjustments, in particular, financial investments, internal operations, goodwill and exchange rate differences. It is found out that to get information about internal operations and financial investments such data have to be synthesized from internal statements. This approach allows using the same accounting methods to parent and subsidiary entities. The objects, the users and the subject domain of internal statements are determined in order to make consolidation of financial statements of joining.

  4. Sleep-dependent memory consolidation in patients with sleep disorders.

    Science.gov (United States)

    Cipolli, Carlo; Mazzetti, Michela; Plazzi, Giuseppe

    2013-04-01

    Sleep can improve the off-line memory consolidation of new items of declarative and non-declarative information in healthy subjects, whereas acute sleep loss, as well as sleep restriction and fragmentation, impair consolidation. This suggests that, by modifying the amount and/or architecture of sleep, chronic sleep disorders may also lead to a lower gain in off-line consolidation, which in turn may be responsible for the varying levels of impaired performance at memory tasks usually observed in sleep-disordered patients. The experimental studies conducted to date have shown specific impairments of sleep-dependent consolidation overall for verbal and visual declarative information in patients with primary insomnia, for verbal declarative information in patients with obstructive sleep apnoeas, and for visual procedural skills in patients with narcolepsy-cataplexy. These findings corroborate the hypothesis that impaired consolidation is a consequence of the chronically altered organization of sleep. Moreover, they raise several novel questions as to: a) the reversibility of consolidation impairment in the case of effective treatment, b) the possible negative influence of altered prior sleep also on the encoding of new information, and c) the relationships between altered sleep and memory impairment in patients with other (medical, psychiatric or neurological) diseases associated with quantitative and/or qualitative changes of sleep architecture. Copyright © 2012 Elsevier Ltd. All rights reserved.

  5. Experimental consolidation of granulated rock salt with application to sleeve buckling. Technical memorandum report RSI-0044

    International Nuclear Information System (INIS)

    Hansen, F.D.

    1976-01-01

    Quasi-static and creep consolidation tests have been performed in order to determine the compressibility of granulated rock salt when subjected to uniaxial deformations. The purpose of this analysis is to evaluate the force-displacement characteristics of rock salt that may be used as a backfill material around waste canister sleeves. The test set-up involved placing rock salt pellets in a thin-walled steel cylinder and applying a uniaxial load which compressed the salt while allowing no lateral movement. Tests were run at room temperature, 100 and 200 0 C and consolidated to uniaxial stress levels between 1000 and 4000 psi. Axial force, displacement and time were monitored during each test and the relationships have been evaluated. In particular, compressibility of the rock salt is not drastically effected by the temperature differences, nor is there an appreciable difference between the consolidation tests that were allowed to creep and those that were tested quasi-statically. On the basis of experimental data relating volume change to uniaxial stress, the pressure on the waste canister sleeve has been shown to be a nonlinear function of drillhole displacement. For a proposed in situ field test geometry, a 16 inch drillhole and a canister with a 12.75 inch O.D., the pressure necessary to buckle the canister sleeve will develop when the drillhole closes diametrically 0.5 to 0.6 inches. By the nature of this experimental effort, the results obtained are conservative

  6. The CCCTB Concept of Consolidation and the Rules on Entering a Group

    NARCIS (Netherlands)

    van de Streek, J.

    2012-01-01

    The consolidation element is at the heart of the proposed Directive on a harmonized Common Consolidated Corporate Tax Base (CCCTB). In this article, the author examines the scope of the consolidation concept. When a company enters a consolidated group, conflicts of interest arise between Member

  7. 17 CFR 210.3A-02 - Consolidated financial statements of the registrant and its subsidiaries.

    Science.gov (United States)

    2010-04-01

    ... 1975 Consolidated and Combined Financial Statements § 210.3A-02 Consolidated financial statements of... consolidated financial statements principles of inclusion or exclusion which will clearly exhibit the financial... 17 Commodity and Securities Exchanges 2 2010-04-01 2010-04-01 false Consolidated financial...

  8. 17 CFR 210.3A-03 - Statement as to principles of consolidation or combination followed.

    Science.gov (United States)

    2010-04-01

    ... Consolidated and Combined Financial Statements § 210.3A-03 Statement as to principles of consolidation or... of (1) subsidiaries in consolidated or combined financial statements and (2) companies in consolidated or combined financial statements, shall be stated in the notes to the respective financial...

  9. Impaired memory consolidation in children with obstructive sleep disordered breathing.

    Directory of Open Access Journals (Sweden)

    Kiran Maski

    Full Text Available Memory consolidation is stabilized and even enhanced by sleep (and particularly by 12-15 Hz sleep spindles in NREM stage 2 sleep in healthy children but it is unclear what happens to these processes when sleep is disturbed by obstructive sleep disordered breathing. This cross-sectional study investigates differences in declarative memory consolidation among children with primary snoring (PS and obstructive sleep apnea (OSA compared to controls. We further investigate whether memory consolidation group differences are associated with NREM stage 2 (N2 sigma (12-15 Hz or NREM slow oscillation (0.5-1 Hz spectral power bands. In this study, we trained and tested participants on a spatial declarative memory task with cued recall. Retest occurred after a period of daytime wake (Wake or a night of sleep (Sleep with in-lab polysomnography. 36 participants ages 5-9 years completed the protocol: 14 with OSA as defined by respiratory disturbance index (RDI > 1/hour, 12 with primary snoring (PS and 10 controls. OSA participants had poorer overall memory consolidation than controls across Wake and Sleep conditions [OSA: mean = -18.7% (5.8, controls: mean = 1.9% (7.2, t = -2.20, P = 0.04]. In contrast, PS participants and controls had comparable memory consolidation across conditions (t = 0.41; P = 0.38. We did not detect a main effect for condition (Sleep, Wake or group x condition interaction on memory consolidation. OSA participants had lower N2 sigma power than PS (P = 0.03 and controls (P = 0.004 and N2 sigma power inversely correlated with percentage of time snoring on the study night (r = -0.33, P<0.05. Across all participants, N2 sigma power modestly correlated with memory consolidation in both Sleep (r = 0.37, P = 0.03 and Wake conditions (r = 0.44, P = 0.009. Further observed variable path analysis showed that N2 sigma power mediated the relationship between group and mean memory consolidation across Sleep and Wake states [Bindirect = 6.76(3.5, z = 2

  10. Concurrent Chemoradiation Therapy Followed by Consolidation Chemotherapy for Localized Extranodal Natural Killer/T-Cell Lymphoma, Nasal Type

    Energy Technology Data Exchange (ETDEWEB)

    Oh, Dongryul [Department of Radiation Oncology, Samsung Medical Center, Sungkyunkwan University School of Medicine, Seoul (Korea, Republic of); Ahn, Yong Chan, E-mail: ycahn.ahn@samsung.com [Department of Radiation Oncology, Samsung Medical Center, Sungkyunkwan University School of Medicine, Seoul (Korea, Republic of); Kim, Seok Jin; Kim, Won Seog [Division of Hematology and Oncology, Department of Medicine, Samsung Medical Center, Sungkyunkwan University School of Medicine, Seoul (Korea, Republic of); Ko, Young Hyeh [Department of Pathology, Samsung Medical Center, Sungkyunkwan University School of Medicine, Seoul (Korea, Republic of)

    2015-11-01

    Purpose: To evaluate the effectiveness of concurrent chemoradiation therapy (CCRT) with 40 Gy followed by consolidation chemotherapy for localized extranodal natural killer (NK)/T-cell lymphoma (ENKTL), nasal type. Methods and Materials: From August 2004 to August 2012, 62 patients with newly diagnosed stage IE to IIE ENKTL underwent CCRT followed by consolidation chemotherapy. The median RT dose was 40 Gy. Cisplatin, 30 mg/m{sup 2}, was administered weekly during the RT course. Responders to CCRT were encouraged to undergo consolidation chemotherapy. Three different consolidation chemotherapy regimens were used consecutively: VIPD (etoposide, ifosfamide, cisplatin, and dexamethasone); VIDL (etoposide, ifosfamide, and dexamethasone followed by intramuscular injection of L-asparaginase); and MIDLE (methotrexate, etoposide, ifosfamide, mesna, and L-asparaginase). Results: The median follow-up period was 49 months (range 8-112). After completion of CCRT, 56 patients (90.3%) had a complete response, 4 (6.4%) had a partial response, 1 (1.6%) had stable disease, and 1 patient (1.6%) had progressive disease (PD). Consolidation chemotherapy was recommended to 61 patients, after excluding the patient with PD, but was actually delivered to 58. Of these 58 patients, 56 (96.5%) had a complete response and 2 (3.5%) had PD. During the follow-up period, 17 patients (including 3 with PD) experienced progression. The median interval to progression was 11 months (range 1-61). Local failure developed in 6 patients, of whom, 2 had developed progression outside the RT field. For all patients, the 3-year overall survival, progression-free survival, and local control rates were 83.1%, 77.1%, and 92.4%, respectively. Grade ≥3 nonhematologic toxicity developed in only 3 patients (4.8%). Conclusions: Excellent clinical outcomes were achieved using CCRT with 40 Gy followed by consolidation chemotherapy. Additional investigation, however, is warranted to confirm our findings.

  11. Lessons learned from the EG ampersand G consolidated hazardous waste subcontract and ESH ampersand Q liability assessment process

    International Nuclear Information System (INIS)

    Fix, N.J.

    1995-03-01

    Hazardous waste transportation, treatment, recycling, and disposal contracts were first consolidated at the Idaho National Engineering Laboratory in 1992 by EG and G Idaho, Inc. At that time, disposition of Resource, Conservation and Recovery Act hazardous waste, Toxic Substance Control Act waste, Comprehensive Environmental Response, Compensation, and Liability Act hazardous substances and contaminated media, and recyclable hazardous materials was consolidated under five subcontracts. The wastes were generated by five different INEL M and O contractors, under the direction of three different Department of Energy field offices. The consolidated contract reduced the number of facilities handling INEL waste from 27 to 8 qualified treatment, storage, and disposal facilities, with brokers specifically prohibited. This reduced associated transportation costs, amount and cost of contractual paperwork, and environmental liability exposure. EG and G reviewed this approach and proposed a consolidated hazardous waste subcontract be formed for the major EG and G managed DOE sites: INEL, Mound, Rocky Flats, Nevada Test Site, and 10 satellite facilities. After obtaining concurrence from DOE Headquarters, this effort began in March 1992 and was completed with the award of two master task subcontracts in October and November 1993. In addition, the effort included a team to evaluate the apparent awardee's facilities for environment, safety, health, and quality (ESH and Q) and financial liability status. This report documents the evaluation of the process used to prepare, bid, and award the EG and G consolidated hazardous waste transportation, treatment, recycling, and/or disposal subcontracts and associated ESH and Q and financial liability assessments; document the strengths and weaknesses of the process; and propose improvements that would expedite and enhance the process for other DOE installations that used the process and for the re-bid of the consolidated subcontract

  12. Lessons learned from the EG&G consolidated hazardous waste subcontract and ESH&Q liability assessment process

    Energy Technology Data Exchange (ETDEWEB)

    Fix, N.J.

    1995-03-01

    Hazardous waste transportation, treatment, recycling, and disposal contracts were first consolidated at the Idaho National Engineering Laboratory in 1992 by EG&G Idaho, Inc. At that time, disposition of Resource, Conservation and Recovery Act hazardous waste, Toxic Substance Control Act waste, Comprehensive Environmental Response, Compensation, and Liability Act hazardous substances and contaminated media, and recyclable hazardous materials was consolidated under five subcontracts. The wastes were generated by five different INEL M&O contractors, under the direction of three different Department of Energy field offices. The consolidated contract reduced the number of facilities handling INEL waste from 27 to 8 qualified treatment, storage, and disposal facilities, with brokers specifically prohibited. This reduced associated transportation costs, amount and cost of contractual paperwork, and environmental liability exposure. EG&G reviewed this approach and proposed a consolidated hazardous waste subcontract be formed for the major EG&G managed DOE sites: INEL, Mound, Rocky Flats, Nevada Test Site, and 10 satellite facilities. After obtaining concurrence from DOE Headquarters, this effort began in March 1992 and was completed with the award of two master task subcontracts in October and November 1993. In addition, the effort included a team to evaluate the apparent awardee`s facilities for environment, safety, health, and quality (ESH&Q) and financial liability status. This report documents the evaluation of the process used to prepare, bid, and award the EG&G consolidated hazardous waste transportation, treatment, recycling, and/or disposal subcontracts and associated ESH&Q and financial liability assessments; document the strengths and weaknesses of the process; and propose improvements that would expedite and enhance the process for other DOE installations that used the process and for the re-bid of the consolidated subcontract, scheduled for 1997.

  13. EVALUATIONS OF BIOTECHNICAL CONSOLIDATIONS OF SLOPES GULLIES IN OPOKA DUŻA (LUBLIN UPLAND

    Directory of Open Access Journals (Sweden)

    Andrzej Mazur

    2017-10-01

    Full Text Available The studies were carried out in consolidated gullies in Opoka Duża, an anti-erosion biotechnical structure created in 1962-1964. On the basis of the studies it can be stated that the applied gullies buildings appeared to be efficient. Gullies did not deepen and did not increase its dimensions, whereas the Sanna river bed did not require expensive dredging. Accumulation of soil material is mainly observed at the bottoms of the gullies. In 51 years, about 4000 m3 of material accumulated at the bottoms. Hydrotechnical structures efficiently strengthened the erosion thresholds and bottoms of gullies against linear erosion and contributed to the inhibition of the fertile soil material creating more favourable conditions for plants growth. However, application of this type of buildings in gullies should be reduced to a necessary minimum, due to the high cost of maintaining a m3 of soil material and the introduction of additional elements in the landscape.

  14. APPLICABILITY OF CONSOLIDATED TECHNIQUES IN THE VIEW OF ROMANIAN ACCOUNTING REGULATIONS

    Directory of Open Access Journals (Sweden)

    Cristina Rosu

    2016-06-01

    Full Text Available The accounting regulations are more and more interested in groups of companies. In some cases, these regulations require for preparing the consolidated financial statements. This is the task of the parent company who keeps the consolidated accounts. To accomplish its goals, the consolidated accounting uses a couple of, so-called, consolidation techniques. These are applied in the case of groups of companies with a complex structure. Their goal is to elaborate the consolidated financial statements using a set of methods and empirical skills. In this article we synthetize and apply the consolidation techniques in the view of Romanian accounting regulations. The Romanian practice has revealed, especially, two techniques: one based on direct consolidation and another one based on multiple levels (phased consolidation. Therefore, this work regards only the technical side of consolidated accounting, accounting records being evaded. Furthermore, we focus only on the preparation of the consolidated balance sheet in the case of some hypothetical groups of companies.

  15. A unified theory for systems and cellular memory consolidation.

    Science.gov (United States)

    Dash, Pramod K; Hebert, April E; Runyan, Jason D

    2004-04-01

    The time-limited role of the hippocampus for explicit memory storage has been referred to as systems consolidation where learning-related changes occur first in the hippocampus followed by the gradual development of a more distributed memory trace in the neocortex. Recent experiments are beginning to show that learning induces plasticity-related molecular changes in the neocortex as well as in the hippocampus and with a similar time course. Present memory consolidation theories do not account for these findings. In this report, we present a theory (the C theory) that incorporates these new findings, provides an explanation for the length of time for hippocampal dependency, and that can account for the apparent longer consolidation periods in species with larger brains. This theory proposes that a process of cellular consolidation occurs in the hippocampus and in areas of the neocortex during and shortly after learning resulting in long-term memory storage in both areas. For a limited time, the hippocampus is necessary for memory retrieval, a process involving the coordinated reactivation of these areas. This reactivation is later mediated by longer extrahippocampal connectivity between areas. The delay in hippocampal-independent memory retrieval is the time it takes for gene products in these longer extrahippocampal projections to be transported from the soma to tagged synapses by slow axonal transport. This cellular transport event defines the period of hippocampal dependency and, thus, the duration of memory consolidation. The theoretical description for memory consolidation presented in this review provides alternative explanations for several experimental observations and presents a unification of the concepts of systems and cellular memory consolidation.

  16. Rheometrical experiments with monitoring of resistivity: for a better understanding of the solid-fluid transition in clayey landslides

    Science.gov (United States)

    Carrière, Simon; Bièvre, Grégory; Chambon, Guillaume; Jongmans, Denis; Lebourg, Thomas; Larose, Eric

    2015-04-01

    Landslides are natural and complex phenomena which affect all types of geological formations and present a large variety of size, morphology and displacements rates. Among these phenomena, flow-like events in clay-rich formations are particularly complex due to the unpredictable acceleration and fluidization that characterize them. Because of their suddenness, such landslides constitute serious threat for population living in these areas. The forecast and the understanding of these events has then been an active topic of research in the scientific community during the past decades. In that respect, rheometrical experiments in the laboratory bring some insight into the processes occurring during the solid-fluid transition. In creep tests, the evolution of the shear strain rate is measured under constant levels of shear stress, allowing to follow changes in apparent viscosity with time and to observe fluidization. Rheometrical oscillatory tests have been designed to capture the evolution of the elastic shear modulus G (and hence the shear wave velocity Vs) during these creep phases. Previous results have shown that Vs exhibits a drop at the solid-fluid transition, with complex time-dependent effects which could lead, under transient loading, to the occurrence of Vs variations prior to the transition. A complementary way to understand the processes is to measure the electrical resistivity during these rheometrical tests. This parameter, which depends on the water content and salinity, as well as on the amount of clay particles, could also exhibit some changes before or during the solid-fluid transition. For that purpose, the metallic plates of the rotational rheometer have been replaced by new ones made in an electrically insulating material (PVC) with a configuration of four inserted circular electrodes. Rheometrical tests made with this new apparatus provide similar rheological results. For the electrical tests, the geometrical factor has been computed using Finite

  17. Effect of application of dairy manure, effluent and inorganic fertilizer on nitrogen leaching in clayey fluvo-aquic soil: A lysimeter study.

    Science.gov (United States)

    Fan, Jianling; Xiao, Jiao; Liu, Deyan; Ye, Guiping; Luo, Jiafa; Houlbrooke, David; Laurenson, Seth; Yan, Jing; Chen, Lvjun; Tian, Jinping; Ding, Weixin

    2017-08-15

    Dairy farm manure and effluent are applied to cropland in China to provide a source of plant nutrients, but there are concerns over its effect on nitrogen (N) leaching loss and groundwater quality. To investigate the effects of land application of dairy manure and effluent on potential N leaching loss, two lysimeter trials were set up in clayey fluvo-aquic soil in a winter wheat-summer maize rotation cropping system on the North China Plain. The solid dairy manure trial included control without N fertilization (CK), inorganic N fertilizer (SNPK), and fresh (RAW) and composted (COM) dairy manure. The liquid dairy effluent trial consisted of control without N fertilization (CF), inorganic N fertilizer (ENPK), and fresh (FDE) and stored (SDE) dairy effluent. The N application rate was 225kgNha -1 for inorganic N fertilizer, dairy manure, and effluent treatments in both seasons. Annual N leaching loss (ANLL) was highest in SNPK (53.02 and 16.21kgNha -1 in 2013/2014 and 2014/2015, respectively), which were 1.65- and 2.04-fold that of COM, and 1.59- and 1.26-fold that of RAW. In the effluent trial (2014/2015), ANLL for ENPK and SDE (16.22 and 16.86kgNha -1 , respectively) were significantly higher than CF and FDE (6.3 and 13.21kgNha -1 , respectively). NO 3 - contributed the most (34-92%) to total N leaching loss among all treatments, followed by dissolved organic N (14-57%). COM showed the lowest N leaching loss due to a reduction in NO 3 - loss. Yield-scaled N leaching in COM (0.35kgNMg -1 silage) was significantly (Pleaching loss while ensuring high crop yield in the North China Plain. Copyright © 2017 Elsevier B.V. All rights reserved.

  18. Investigation of the mechanical behaviour of gas-hydrate bearing clayey sediments from the Gulf of Guinea using in-situ geotechnical measurements

    Science.gov (United States)

    Taleb, F.; Garziglia, S.; Sultan, N.

    2017-12-01

    Expanding needs for energy resources and concerns about climate change have moved industrial and academic interests towards regions where specific thermobaric conditions allow the formation of gas hydrates (GH). While significant advances have been made to characterize the fabric and structure of these metastable geo-compounds, considerable uncertainty remains regarding the impact of their mechanical properties on the seafloor morphology and stability. This is particularly true for gas hydrates-bearing fine-grained sediments, which remain challenging to preserve or synthesise prior to laboratory testing. As a step towards understanding the mechanical consequences of the concentration and distribution of GH in this type of sediments, this work uses acoustic and geotechnical in situ measurements collected in a high gas flux system offshore Nigeria. Acoustic measurements of compressional wave velocity were shown to be convenient means of both detecting and quantifying gas hydrates in marine sediments. Geotechnical data derived from piezocone readings and their distribution in normalised soil classification charts allowed identifying distinct features of gas hydrates-bearing clayey sediments; such as a mechanical behaviour sharing similarities with that of cemented clays. Correlations between acoustic and piezocone data showed that the stiffness and strength tend to generally increase with increasing GH concentrations. However, several sediment intervals sharing the same hydrates concentration have revealed different features of mechanical behaviour. This was linked to the presence of various GH morphologies within the marine sediments such as groups of hydrate veins or massive hydrate nodules. This in-situ approach allowing both understanding the heterogeneous distribution of GH and characterising their host sediment seems key to assess the potential link between seafloor stability and GH dissociation/dissolution caused by human activities or by natural environmental

  19. Processing of porous zirconia ceramics by direct consolidation with starch

    International Nuclear Information System (INIS)

    Garrido, Liliana B; Albano, Maria P

    2008-01-01

    Porous ceramics are used especially for those environments with high temperatures, heavy wear and in a corrosive medium. Zirconium-based materials are useful for such applications as sensors, filters, support for catalytic reactions, porous components for sofc and in biomedical applications. A conventional method for producing porous ceramics consists of the addition and later decomposition by calcination (pyrolisis) of different organic materials that act as pore formers. Several wet processing possibilities have been developed. Among these is a technique of direct consolidation with starch. This process begins with the preparation of an aqueous suspension of the ceramic with the dispersants needed to stabilize it, to which the starch is added. After casting in a waterproof mold, the suspension thermally hardens into the desired shape. The dry compacts undergo the sintering cycle to obtain pieces almost in their final form. This study aims to optimize the processing of porous zirconium ceramics using starch as a pore and binder forming agent. Zirconium with 3% yttrium molar stabilized in tetragonal phase was used. The aqueous suspensions (52-55% vol) of the zirconium-starch mixtures with different compositions were stabilized with a commercial solution of ammonium polyacrylate as a dispersant and were hardened in plastic molds at 90 o C for 30 min. The influence of added volume of starch on the physical characteristics of the pieces in green state was established while maintaining the temperature, the gelling time and the conditions of constant drying. The sintering was carried out at 1000-1500 o C-2h. The characteristics of the sintered product were evaluated by measuring density, volumetric contraction, intrusion of Hg and the evolution of the crystalline phases by X-ray diffraction (XRD) and scanning electron microscopy (SEM). The microstructural properties of ceramic (pore volume, the relation between open and closed porosity, size distribution, morphology of

  20. Dissociation of explicit and implicit long-term memory consolidation in semantic dementia: a case study.

    Science.gov (United States)

    Tu, S; Mioshi, E; Savage, S; Hodges, J R; Hornberger, M

    2013-08-01

    We report a case study of a semantic dementia patient, whose episodic memory consolidation was tested over a 2-month period. The results reveal that despite early retention of information, the patient lost all explicit information of the newly learnt material after 2 weeks. By contrast, he retained implicit word information even after a 4-week delay. These findings highlight the critical time window of 2-4 weeks in which newly learnt information should be re-encoded in rehabilitations studies. The results also indicate that learnt information can be still accessed with implicit retrieval strategies when explicit retrieval fails.