WorldWideScience

Sample records for configuration design energy

  1. Ocean Thermal Energy Conversion (OTEC) platform configuration and integration. Volume II. Conceptual design. Final report

    Energy Technology Data Exchange (ETDEWEB)

    None

    1978-06-01

    The purpose of this project is to evaluate six candidate hullforms as candidates for the OTEC commercial plant. This volume is a summary of the conceptual design including facility requirements, cost, schedule, and site sensitivity. Two OTEC commercial plant configurations are considered in this study: the ship and the semi-submersible. Engineering drawings are presented. (WHR)

  2. Dark energy stars: Stable configurations

    CERN Document Server

    Bhar, Piyali; Rahaman, Farook; Banerjee, Ayan

    2016-01-01

    In present paper a spherically symmetric stellar configuration has been analyzed by assuming the matter distribution of the stellar configuration is anisotropic in nature and compared with the realistic objects, namely, the low mass X-ray binaries (LMXBs) and X-ray pulsars. The analytic solution has been obtained by utilizing the dark energy equation of state for the interior solution corresponding to the Schwarzschild exterior vacuum solution at the junction interface. Several physical properties like energy conditions, stability, mass-radius ratio, and surface redshift are described through mathematical calculations as well as graphical plots. It is found that obtained mass-radius ration of the compact stars candidates like 4U 1820-30, PSR J 1614-2230, Vela X-1 and Cen X-3 are very much consistent with the observed data by Gangopadhyay et al. (Mon. Not. R. Astron. Soc. 431, 3216 (2013)). So our proposed model would be useful in the investigation of the possible clustering of dark energy.

  3. Combined method for parallel manipulator configuration design

    Institute of Scientific and Technical Information of China (English)

    2005-01-01

    Configuration design is an essential, creative and decision-making step in parallel manipulator design process, in which modeling and assembly are iterative and trivial. Combined approach with automatic parametric modeling and automatic assembly is proposed for parallel manipulator configuration design. The design process and key techniques, such as configuration design, configuration verification, poses calculation of all parts in parallel manipulator, virtual assembly and etc., are discussed and demonstrated by an example. A software package is developed for parallel manipulator configuration design based on the proposed method with Visual C+ + and UG/OPEN on Unigraphics.

  4. Initial DEMO tokamak design configuration studies

    Energy Technology Data Exchange (ETDEWEB)

    Bachmann, Christian, E-mail: christian.bachmann@efda.org [EFDA, Boltzmannstraße 2, 85748 Garching (Germany); Aiello, G. [CEA-Saclay, DEN, DM2S, SEMT, F-91191 Gif-Sur-Yvette (France); Albanese, R.; Ambrosino, R. [ENEA/CREATE, Universita di Napoli Federico II, Naples (Italy); Arbeiter, F. [Karlsruhe Institute of Technology (KIT), Karlsruhe (Germany); Aubert, J. [CEA-Saclay, DEN, DM2S, SEMT, F-91191 Gif-Sur-Yvette (France); Boccaccini, L.; Carloni, D. [Karlsruhe Institute of Technology (KIT), Karlsruhe (Germany); Federici, G. [EFDA, Boltzmannstraße 2, 85748 Garching (Germany); Fischer, U. [Karlsruhe Institute of Technology (KIT), Karlsruhe (Germany); Kovari, M. [CCFE, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom); Li Puma, A. [CEA-Saclay, DEN, DM2S, SEMT, F-91191 Gif-Sur-Yvette (France); Loving, A. [CCFE, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom); Maione, I. [Karlsruhe Institute of Technology (KIT), Karlsruhe (Germany); Mattei, M. [ENEA/CREATE, Universita di Napoli Federico II, Naples (Italy); Mazzone, G. [ENEA C.R. Frascati, via E. Fermi 45, 00044 Frascati, Roma (Italy); Meszaros, B. [EFDA, Boltzmannstraße 2, 85748 Garching (Germany); Palermo, I. [Centro de Investigaciones Energéticas, Medioambientales y Tecnológicas (CIEMAT), Madrid (Spain); Pereslavtsev, P. [Karlsruhe Institute of Technology (KIT), Karlsruhe (Germany); Riccardo, V. [CCFE, Culham Science Centre, Abingdon, Oxon OX14 3DB (United Kingdom); and others

    2015-10-15

    Highlights: • A definition of main DEMO requirements. • A description of the DEMO tokamak design configuration. • A description of issues yet to be solved. - Abstract: To prepare the DEMO conceptual design phase a number of physics and engineering assessments were carried out in recent years in the frame of EFDA concluding in an initial design configuration of a DEMO tokamak. This paper gives an insight into the identified engineering requirements and constraints and describes their impact on the selection of the technologies and design principles of the main tokamak components. The EU DEMO program aims at making best use of the technologies developed for ITER (e.g., magnets, vessel, cryostat, and to some degree also the divertor). However, other systems in particular the breeding blanket require design solutions and advanced technologies that will only partially be tested in ITER. The main differences from ITER include the requirement to breed, to extract, to process and to recycle the tritium needed for plasma operation, the two orders of magnitude larger lifetime neutron fluence, the consequent radiation dose levels, which limit remote maintenance options, and the requirement to use low-activation steel for in-vessel components that also must operate at high temperature for efficient energy conversion.

  5. Ecolifter Conceptual Configuration Design and Parameter Analysis

    Institute of Scientific and Technical Information of China (English)

    唐胜景

    2003-01-01

    In the phase of conceptually designing, the Ecolifter with three-lift-surface configuration, the influences of aircraft geometric parameters and configuration such as wing geometric parameters, canard parameters, aircraft center of gravity and engine positions and so on, on flight dynamic stability are discussed with the integrated analysis method. On the basis of the analysis of flight dynamic stability, the suitable wing geometric parameters are given and the improved aircraft configuration is proposed.

  6. Configurational space continuity and free energy calculations

    CERN Document Server

    Tian, Pu

    2016-01-01

    Free energy is arguably the most importance function(al) for understanding of molecular systems. A number of rigorous and approximate free energy calculation/estimation methods have been developed over many decades. One important issue, the continuity of an interested macrostate (or path) in configurational space, has not been well articulated, however. As a matter of fact, some important special cases have been intensively discussed. In this perspective, I discuss the relevance of configurational space continuity in development of more efficient and reliable next generation free energy methodologies.

  7. Electrochemical systems configured to harvest heat energy

    Science.gov (United States)

    Lee, Seok Woo; Yang, Yuan; Ghasemi, Hadi; Chen, Gang; Cui, Yi

    2017-01-31

    Electrochemical systems for harvesting heat energy, and associated electrochemical cells and methods, are generally described. The electrochemical cells can be configured, in certain cases, such that at least a portion of the regeneration of the first electrochemically active material is driven by a change in temperature of the electrochemical cell. The electrochemical cells can be configured to include a first electrochemically active material and a second electrochemically active material, and, in some cases, the absolute value of the difference between the first thermogalvanic coefficient of the first electrochemically active material and the second thermogalvanic coefficient of the second electrochemically active material is at least about 0.5 millivolts/Kelvin.

  8. Multi-Imagery Exploitation Configuration Design Study.

    Science.gov (United States)

    1982-11-01

    A124 88? MULTI-IMAGERY ENPLOITRTION CONFIGURATION DESIGN STUDY 1/2 (U) HARRIS CORP MEL8OURNE FL GOVERNMENT COMMUNICATION SYSTEMS DIV T E TIMOTHY ET...DESIGN STUDY 212 (U) HARRIS CORP MELBOURNE FL GOVERNMENT COMMUNICATION SYSTEMS DIV T E TIMOTHY ET AL. NOV 82 RRDC-TR-82-33 UNCLASSIFIED F31692-Si-C-8095 F

  9. Sectorization and Configuration Transition in Airspace Design

    Directory of Open Access Journals (Sweden)

    Xiang Zou

    2016-01-01

    Full Text Available Current airspace is sectorized according to some predefined rules that are not flexible. To facilitate utilizing the airspace more efficiently, methods to design sectors need to be promoted. In this paper, we propose an undirected graph cut-based approach that employs a memetic local search-embedded constrained evolution algorithm, NSGA-II, to generate nondominated airspace configurations. We also propose a new concave hull-based method to automatically depict sector boundaries. In addition, we also study the configuration transition problem. We define the similarity of the two different configurations and calculate their similarity with a bisection diagram and a minimum cost flow algorithm. We build a forward network to represent configuration transitions across several consecutive time periods and use multiobjective dynamic programming to determine a series of nondominated configuration links from the first period to the end. We test our approaches by simulation in high-altitude airspace controlled by Beijing Area Control Center. The results show that our sectorization method outperforms the current configuration in practice, providing a lower sector number, lower intersector flow, more balanced workload distribution among the different sectors, and no constraint violations, so that the proposed approach shows its significant potential as practical applications for dynamic airspace configuration.

  10. Sustainable supply chain design: a configurational approach.

    Science.gov (United States)

    Masoumik, S Maryam; Abdul-Rashid, Salwa Hanim; Olugu, Ezutah Udoncy; Raja Ghazilla, Raja Ariffin

    2014-01-01

    Designing the right supply chain that meets the requirements of sustainable development is a significant challenge. Although there are a considerable number of studies on issues relating to sustainable supply chain design (SSCD) in terms of designing the practices, processes, and structures, they have rarely demonstrated how these components can be aligned to form an effective sustainable supply chain (SSC). Considering this gap in the literature, this study adopts the configurational approach to develop a conceptual framework that could configure the components of a SSC. In this respect, a process-oriented approach is utilized to classify and harmonize the design components. A natural-resource-based view (NRBV) is adopted to determine the central theme to align the design components around. The proposed framework presents three types of SSC, namely, efficient SSC, innovative SSC, and reputed SSC. The study culminates with recommendations concerning the direction for future research.

  11. Sustainable Supply Chain Design: A Configurational Approach

    Science.gov (United States)

    Masoumik, S. Maryam; Raja Ghazilla, Raja Ariffin

    2014-01-01

    Designing the right supply chain that meets the requirements of sustainable development is a significant challenge. Although there are a considerable number of studies on issues relating to sustainable supply chain design (SSCD) in terms of designing the practices, processes, and structures, they have rarely demonstrated how these components can be aligned to form an effective sustainable supply chain (SSC). Considering this gap in the literature, this study adopts the configurational approach to develop a conceptual framework that could configure the components of a SSC. In this respect, a process-oriented approach is utilized to classify and harmonize the design components. A natural-resource-based view (NRBV) is adopted to determine the central theme to align the design components around. The proposed framework presents three types of SSC, namely, efficient SSC, innovative SSC, and reputed SSC. The study culminates with recommendations concerning the direction for future research. PMID:24523652

  12. Energy barrier for configurational transformation of graphene nanoribbon on nanotube

    Directory of Open Access Journals (Sweden)

    Qifang Yin

    2014-01-01

    Full Text Available A graphene nanoribbon (GNR has two basic configurations when winding on the outer surface of a carbon nanotube (CNT: helix and scroll. Here the transformation between the two configurations is studied utilizing molecular dynamics simulations. The energy barrier during the transformation as well as its relationship with the interfacial energy and the radius of CNT are investigated. Our work offers further insights into the formation of desirable helix/scroll of GNR winding on nanotubes or nanowires, and thus can enable novel design of potential graphene-based electronics.

  13. Automated firewall analytics design, configuration and optimization

    CERN Document Server

    Al-Shaer, Ehab

    2014-01-01

    This book provides a comprehensive and in-depth study of automated firewall policy analysis for designing, configuring and managing distributed firewalls in large-scale enterpriser networks. It presents methodologies, techniques and tools for researchers as well as professionals to understand the challenges and improve the state-of-the-art of managing firewalls systematically in both research and application domains. Chapters explore set-theory, managing firewall configuration globally and consistently, access control list with encryption, and authentication such as IPSec policies. The author

  14. Solar PV Energy Conversion System and its Configurations

    OpenAIRE

    Ahteshamul Haque

    2016-01-01

    Solar PV based energy conversion system is now used in commercial and residential buildings. Advancements in Power electronics leads the researchers to enhance the use of solar application in various configurations. These configurations may be used to utilize the energy optimally. The main objective of this paper is to present an overview of the various configurations of solar PV energy conversion system

  15. Spacecraft (Mobile Satellite) configuration design study

    Science.gov (United States)

    1985-01-01

    The relative costs to procure and operate a two-satellite mobile satellite system designed to operate either in the UHF band of the L Band, and with several antenna diameter options in each frequency band was investigated. As configured, the size of the spacecraft is limited to the current RCA Series 4000 Geosynchronous Communications Spacecraft bus, which spans the range from 4000 to 5800 pounds in the transfer orbit. The Series 4000 bus forms the basis around which the Mobile Satellite transponder and associated antennas were appended. Although the resultant configuration has little outward resemblance to the present Series 4000 microwave communications spacecraft, the structure, attitude control, thermal, power, and command and control subsystems of the Series 4000 spacecraft are all adapted to support the Mobile Satellite mission.

  16. Energy design for architects

    Energy Technology Data Exchange (ETDEWEB)

    Shaw, A. (American Architectual Foundation (US))

    1988-01-01

    This text examines the design considerations which need to be taken into account in meeting client requirements for building operating efficiency. Siting elements including orientation and configuration, underground design options, and sun and wind control are fully explored. The reader is taken step by step from siting and space planning through the construction process, covering building envelope, fenestration and other apertures, structure and mass, lighting, thermal systems, process and domestic hot water, and energy management and control systems. The final chapters present detailed energy use and performance analysis techniques as well as payback assessment procedures. An extensive glossary and index are also provided.

  17. Human Mars Ascent Configuration and Design Sensitivities

    Science.gov (United States)

    Polsgrove, Tara P.; Gernhardt, Mike; Collins, Tim; Martin, John

    2017-01-01

    Human missions to Mars may utilize several small cabins where crew members could live for days up to a couple of weeks. At the end of a Mars surface mission the Mars Ascent Vehicle (MAV) crew cabin would carry the crew to their destination in orbit in a matter of hours or days. Other small cabins in support of a Mars mission would include pressurized rovers that allow crew members to travel great distances from their primary habitat on Mars while unconstrained by time limits of typical EVAs. An orbital crew taxi could allow for exploration of the moons of Mars with minimum impact to the primary Earth-Mars transportation systems. A common crew cabin design that can perform in each of these applications is desired and could reduce the overall mission cost. However, for the MAV, the crew cabin size and mass can have a large impact on vehicle design and performance. The total ascent vehicle mass drives performance requirements for the Mars descent systems and the Earth to Mars transportation elements. Minimizing MAV mass is a priority and minimizing the crew cabin size and mass is one way to do that. This paper explores the benefits and impacts of using a common crew cabin design for the MAV. Results of a MAV configuration trade study will be presented along with mass and performance estimates for the selected design.

  18. MarFS-Requirements-Design-Configuration-Admin

    Energy Technology Data Exchange (ETDEWEB)

    Kettering, Brett Michael [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Grider, Gary Alan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2015-07-08

    This document will be organized into sections that are defined by the requirements for a file system that presents a near-POSIX (Portable Operating System Interface) interface to the user, but whose data is stored in whatever form is most efficient for the type of data being stored. After defining the requirement the design for meeting the requirement will be explained. Finally there will be sections on configuring and administering this file system. More and more, data dominates the computing world. There is a “sea” of data out there in many different formats that needs to be managed and used. “Mar” means “sea” in Spanish. Thus, this product is dubbed MarFS, a file system for a sea of data.

  19. Solar PV Energy Conversion System and its Configurations

    Directory of Open Access Journals (Sweden)

    Ahteshamul Haque

    2016-02-01

    Full Text Available Solar PV based energy conversion system is now used in commercial and residential buildings. Advancements in Power electronics leads the researchers to enhance the use of solar application in various configurations. These configurations may be used to utilize the energy optimally. The main objective of this paper is to present an overview of the various configurations of solar PV energy conversion system

  20. A Flexible Power Electronics Configuration for Coupling Renewable Energy Sources

    Directory of Open Access Journals (Sweden)

    Mattia Filippini

    2015-05-01

    Full Text Available A combination of series, parallel and multilevel power electronics has been investigated as a potential interface for two different types of renewable energy sources and in order to reach higher power levels. Renewable energy sources are typically dispersed in a territory, and sources, like wind and solar, allow small to medium-scale generation of electricity. The configuration investigated in this article aims at adapting the coupling solution to the specific generation characteristics of the renewable energy source to make it fit the electrical network. The configuration consists of a combination of three-phase multilevel converters and single-phase inverters, which are designed to provide flexibility, high power quality and high efficiency. A detailed analysis and simulation is performed to identify the properties in conjunction with the electrical grid requirements and the potential challenges encountered during operation. An optimized operation example of wind generation combined with solar PV generation is presented to exemplify the flexibility and benefits of the proposed configuration.

  1. Configuration Design of Product Service System for CNC Machine Tools

    OpenAIRE

    Zhongqi Sheng; Tao Xu; Junyou Song

    2015-01-01

    Product service system is a combination of product and services to meet the customer requirements. Configuration design is the key process of product service system development. This paper studies the configuration design of product service system for CNC machine tools. The research explores the configuration design process of product service system development, analyzes the retrieval method of product service system schemes, determines the configuration sequence of product modules and servic...

  2. Energy Configuration of the Buildings from Concept to Implementation

    Directory of Open Access Journals (Sweden)

    Gabriela CARACAS

    2013-07-01

    Full Text Available The paper presents the aim and objectives of modernizing the energy system of current buildings as well as of designing and executing new buildings with a high Energy and Environmental Performance. It is necessary to refer to the European Strategy (Europe 2020 and to the European Directives, transposed into the national legislation, while the technical and economic solutions to the objectives resulting from the above mentioned purpose complete the dimension of the logical structure of this procedure for reaching the objectives. The economic and especially social importance of comfortable and hygienic living conditions, without excessive costs and without affecting the climate also stems from the climate impact on the current living conditions and use of energy sources. The summer of 2003 had a tragic aftermath at the European and international level, consisting in over 40000 victims of the heat wave and of the buildings’ incapacity to adapt to extremes such as exceptionally intense climate hazards. This highlighted the vulnerability of the built environment compared to climate hazards characterized through an ascending evolution, Romania included. The system of quantitative assessment of the building’s Energy and Environmental Performance, part of the procedure for Energy and Environmental Configuration, entails separate expertise and diagnosis phases which allow elaborating scenarios and strategies for energy modernization. The modernization scenarios are elaborated based on the diagnosis of the building, scenarios differentiated through technical and economic indicators. Scenarios allow the modernization strategy to be elaborated. The energy modernization strategy / designing of new, energy performance buildings is based on the Energy Configuration of Buildings which is the detailed modelling of ownership transfer processes and the assessment of economic efficiency of design / exploitation solutions. The calculation methods are subject to

  3. Casimir energies of self-similar plate configurations

    Science.gov (United States)

    Shajesh, K. V.; Brevik, Iver; Cavero-Peláez, Inés; Parashar, Prachi

    2016-09-01

    We construct various self-similar configurations using parallel δ -function plates and show that it is possible to evaluate the Casimir interaction energy of these configurations using the idea of self-similarity alone. We restrict our analysis to interactions mediated by a scalar field, but the extension to the electromagnetic field is immediate. Our work unveils an easy and powerful method that can be easily employed to calculate the Casimir energies of a class of self-similar configurations. As a highlight, in an example, we determine the Casimir interaction energy of a stack of parallel plates constructed by positioning δ -function plates at the points constituting the Cantor set, a prototype of a fractal. This, to our knowledge, is the first time that the Casimir energy of a fractal configuration has been reported. Remarkably, the Casimir energy of some of the configurations we consider turn out to be positive, and a few even have zero Casimir energy. For the case of positive Casimir energy that is monotonically decreasing as the stacking parameter increases, the interpretation is that the pressure of vacuum tends to inflate the infinite stack of plates. We further support our results, derived using the idea of self-similarity alone, by rederiving them using the Green's function formalism. These expositions gives us insight into the connections between the regularization methods used in quantum field theories and regularized sums of divergent series in number theory.

  4. Configuration management of the EU DEMO conceptual design data

    Energy Technology Data Exchange (ETDEWEB)

    Meszaros, Botond; Shannon, Mark [EUROfusion Consortium, PPPT Department, Garching, Boltzmannstr. 2 (Germany); Marzullo, Domenico [CREATE, University of Naples Federico II, P.le Tecchio 80, 80125 Napoli (Italy); Woodley, Colin; Rowe, Steve [CCFE, Culham Science Centre, Oxfordshire OX14 3DB, Abingdon (United Kingdom); Di Gironimo, Giuseppe [CREATE, University of Naples Federico II, P.le Tecchio 80, 80125 Napoli (Italy)

    2016-11-01

    Highlights: • Description of the selection of the DEMO Product Data Management tool. • Introduction of the DEMO configuration management philosophy for the CAD design data. • Description of the enabling tools and systems of the configuration management. - Abstract: The EUROfusion Consortium is setting up – as part of the EU Fusion Roadmap – the framework for the implementation of the (pre)conceptual design phase of the DEMO reactor. Configuration management needs have been identified as one of the key elements of this framework and is the topic of this paper, in particular the configuration of the CAD design data. The desire is to keep the definition and layout of the corresponding systems “light weight” and relatively easy to manage, whilst simultaneously providing a level of detail in the definition of the design configuration that is fit for the purpose of a conceptual design. This paper aims to describe the steps followed during the definition of the configuration management system of the DEMO design data in terms of (i) the identification of the appropriate product data management system, (ii) the description of the philosophy of the configuration management of the design data, and (iii) the introduction of the most important enabling processes.

  5. Research Design – Composition, Configuration and Interdependencies

    DEFF Research Database (Denmark)

    Kastberg, Peter

    2016-01-01

    In this essay I will present an integrative view on research design. I will introduce what I take to be the skeleton components of any research design within the social sciences, i.e. the elements of research question, philosophy of science, methodology, method and data. With this as my point...... of departure I will go on to focus on a presentation, a discussion and an evaluation of a new appreciation of the interdependencies of the elements in the research design. An appreciation that favors a relational rather than an atomistic outlook and which gives rise to an ecological conceptualization...... of research design. A research design, in other words, which promotes plasticity and fluidity over adherence to static protocol. And which, at the same time, does not relinquish control over project-relevant, multifaceted decision-making processes – and their respective interdependencies – but which...

  6. Research Design – Composition, Configuration and Interdependencies

    DEFF Research Database (Denmark)

    Kastberg, Peter

    2017-01-01

    In this essay I will present an integrative view on research design. I will introduce what I take to be the skeleton components of any research design within the social sciences, i.e. the elements of research question, philosophy of science, methodology, method and data. With this as my point...... of departure I will go on to focus on a presentation, a discussion and an evaluation of a new appreciation of the interdependencies of the elements in the research design. An appreciation that favors a relational rather than an atomistic outlook and which gives rise to an ecological conceptualization...... of research design. A research design, in other words, which promotes plasticity and fluidity over adherence to static protocol. And which, at the same time, does not relinquish control over project-relevant, multifaceted decision-making processes – and their respective interdependencies – but which...

  7. An automated approach to magnetic divertor configuration design

    Science.gov (United States)

    Blommaert, M.; Dekeyser, W.; Baelmans, M.; Gauger, N. R.; Reiter, D.

    2015-01-01

    Automated methods based on optimization can greatly assist computational engineering design in many areas. In this paper an optimization approach to the magnetic design of a nuclear fusion reactor divertor is proposed and applied to a tokamak edge magnetic configuration in a first feasibility study. The approach is based on reduced models for magnetic field and plasma edge, which are integrated with a grid generator into one sensitivity code. The design objective chosen here for demonstrative purposes is to spread the divertor target heat load as much as possible over the entire target area. Constraints on the separatrix position are introduced to eliminate physically irrelevant magnetic field configurations during the optimization cycle. A gradient projection method is used to ensure stable cost function evaluations during optimization. The concept is applied to a configuration with typical Joint European Torus (JET) parameters and it automatically provides plausible configurations with reduced heat load.

  8. Importance of configurational contributions to the free energy of nanoclusters

    Directory of Open Access Journals (Sweden)

    M. Posselt

    2013-07-01

    Full Text Available An effective simulation method based on the Wang-Landau Monte Carlo algorithm is used in order to demonstrate the significance of the configurational contributions to the free energy of embedded nanoclusters. Starting from the most stable cluster configuration the simulation provides all geometrically different, but simply connected and sufficiently compact configurations of a nanocluster of a given size and the respective formation energies. The knowledge of these data allows the calculation of the free formation and free binding energy of the cluster at T ≠ 0. The method is applied to coherent Cu clusters in bcc-Fe. It is shown that even at moderate temperatures the configurational contributions to the free formation and binding energy must not be neglected. The dependence of the monomer free binding energy on clusters size is found to change significantly with increasing temperature which has a considerable effect on the pathway of cluster evolution. Therefore, present investigations provide an essential contribution to the improvement of the input parameters for object kinetic Monte Carlo simulations and rate theory used in multi-scale simulations of the nanostructure evolution. The calculation scheme developed in this work is rather general and applicable to many types of embedded nanoclusters. Compared to the method of overlapping distributions hitherto used in some cases to determine the configurational part of the free energy the new method has major advantages. Various tests are performed in order verify the presented approach and to compare with the results of the other calculation procedure. A roadmap is proposed to include the vibrational contributions to the free energy of the clusters within the framework of the method employed in this work.

  9. Energy design for architects

    Energy Technology Data Exchange (ETDEWEB)

    Shaw, A. (ed.)

    1989-01-01

    This book contains techniques for energy efficiency in architectural design. Many aspects are covered including: cost; comfort and health; energy use; the design process; and analytical techniques. 202 figs. (JF)

  10. Energy efficient building design

    Energy Technology Data Exchange (ETDEWEB)

    1992-03-01

    The fundamental concepts of the building design process, energy codes and standards, and energy budgets are introduced. These tools were combined into Energy Design Guidelines and design contract requirements. The Guidelines were repackaged for a national audience and a videotape for selling the concept to government executives. An effort to test transfer of the Guidelines to outside agencies is described.

  11. Configurable intelligent optimization algorithm design and practice in manufacturing

    CERN Document Server

    Tao, Fei; Laili, Yuanjun

    2014-01-01

    Presenting the concept and design and implementation of configurable intelligent optimization algorithms in manufacturing systems, this book provides a new configuration method to optimize manufacturing processes. It provides a comprehensive elaboration of basic intelligent optimization algorithms, and demonstrates how their improvement, hybridization and parallelization can be applied to manufacturing. Furthermore, various applications of these intelligent optimization algorithms are exemplified in detail, chapter by chapter. The intelligent optimization algorithm is not just a single algorit

  12. Design of a canard configured TransCruiser using CEASIOM

    Science.gov (United States)

    Rizzi, Arthur; Eliasson, Peter; Goetzendorf-Grabowski, Tomasz; Vos, Jan B.; Zhang, Mengmeng; Richardson, Thomas S.

    2011-11-01

    CEASIOM is a multidisciplinary software environment for aircraft design that has been developed as part of the European Framework 6 SimSAC project. It closely integrates discipline-specific tools such as those used for CAD, grid generation, CFD, stability analysis and control system design. The environment allows the user to take an initial design from geometry definition and aerodynamics generation through to full six degrees of freedom simulation and analysis. Key capabilities include variable fidelity aerodynamics tools and aeroelasticity modules. The purpose of this paper is to demonstrate the potential of CEASIOM by presenting the results of a Design, Simulate and Evaluate (DSE) exercise applied to a novel, project specific, transonic cruiser configuration called the TCR. The baseline TCR configuration is first defined using conventional methods, which is then refined and improved within the CEASIOM software environment. A wind tunnel model of this final configuration was then constructed, tested and used to verify the results generated using CEASIOM.

  13. A novel approach to magnetic divertor configuration design

    Science.gov (United States)

    Blommaert, M.; Baelmans, M.; Dekeyser, W.; Gauger, N. R.; Reiter, D.

    2015-08-01

    Divertor exhaust system design and analysis tools are crucial to evolve from experimental fusion reactors towards commercial power plants. In addition to material research and dedicated vessel geometry design, improved magnetic configurations can contribute to sustaining the diverted heat loads. Yet, computational design of the magnetic divertor is a challenging process involving a magnetic equilibrium solver, a plasma edge grid generator and a computationally demanding plasma edge simulation. In this paper, an integrated approach to efficient sensitivity calculations is discussed and applied to a set of slightly reduced divertor models. Sensitivities of target heat load performance to the shaping coil currents are directly evaluated. Using adjoint methods, the cost for a sensitivity evaluation is reduced to about two times the simulation cost of one specific configuration. Further, the use of these sensitivities in an optimal design framework is illustrated by a case with realistic Joint European Torus (JET) configurational parameters.

  14. A Design of Product Collaborative Online Configuration Model

    Science.gov (United States)

    Wang, Xiaoguo; Zheng, Jin; Zeng, Qian

    According to the actual needs of mass customization, the personalization of product and its collaborative design, the paper analyzes and studies the working mechanism of modular-based product configuration technology and puts forward an information model of modular product family. Combined with case-based reasoning techniques (CBR) and the constraint satisfaction problem solving techniques (CSP), we design and study the algorithm for product configuration, and analyze its time complexity. A car chassis is made as the application object, we provide a prototype system of online configuration. Taking advantage of this system, designers can make appropriate changes on the existing programs in accordance with the demand. This will accelerate all aspects of product development and shorten the product cycle. Also the system will provide a strong technical support for enterprises to improve their market competitiveness.

  15. High-Energy Electron Confinement in a Magnetic Cusp Configuration

    Science.gov (United States)

    Park, Jaeyoung; Krall, Nicholas A.; Sieck, Paul E.; Offermann, Dustin T.; Skillicorn, Michael; Sanchez, Andrew; Davis, Kevin; Alderson, Eric; Lapenta, Giovanni

    2015-04-01

    We report experimental results validating the concept that plasma confinement is enhanced in a magnetic cusp configuration when β (plasma pressure/magnetic field pressure) is of order unity. This enhancement is required for a fusion power reactor based on cusp confinement to be feasible. The magnetic cusp configuration possesses a critical advantage: the plasma is stable to large scale perturbations. However, early work indicated that plasma loss rates in a reactor based on a cusp configuration were too large for net power production. Grad and others theorized that at high β a sharp boundary would form between the plasma and the magnetic field, leading to substantially smaller loss rates. While not able to confirm the details of Grad's work, the current experiment does validate, for the first time, the conjecture that confinement is substantially improved at high β . This represents critical progress toward an understanding of the plasma dynamics in a high-β cusp system. We hope that these results will stimulate a renewed interest in the cusp configuration as a fusion confinement candidate. In addition, the enhanced high-energy electron confinement resolves a key impediment to progress of the Polywell fusion concept, which combines a high-β cusp configuration with electrostatic fusion for a compact, power-producing nuclear fusion reactor.

  16. High-Energy Electron Confinement in a Magnetic Cusp Configuration

    Directory of Open Access Journals (Sweden)

    Jaeyoung Park

    2015-06-01

    Full Text Available We report experimental results validating the concept that plasma confinement is enhanced in a magnetic cusp configuration when β (plasma pressure/magnetic field pressure is of order unity. This enhancement is required for a fusion power reactor based on cusp confinement to be feasible. The magnetic cusp configuration possesses a critical advantage: the plasma is stable to large scale perturbations. However, early work indicated that plasma loss rates in a reactor based on a cusp configuration were too large for net power production. Grad and others theorized that at high β a sharp boundary would form between the plasma and the magnetic field, leading to substantially smaller loss rates. While not able to confirm the details of Grad’s work, the current experiment does validate, for the first time, the conjecture that confinement is substantially improved at high β. This represents critical progress toward an understanding of the plasma dynamics in a high-β cusp system. We hope that these results will stimulate a renewed interest in the cusp configuration as a fusion confinement candidate. In addition, the enhanced high-energy electron confinement resolves a key impediment to progress of the Polywell fusion concept, which combines a high-β cusp configuration with electrostatic fusion for a compact, power-producing nuclear fusion reactor.

  17. District Heating Network Design and Configuration Optimization with Genetic Algorithm

    Directory of Open Access Journals (Sweden)

    Hongwei Li

    2013-12-01

    Full Text Available In this paper, the configuration of a district heating network which connects from the heating plant to the end users is optimized. Each end user in the network represents a building block. The connections between the heat generation plant and the end users are represented with mixed integer and the pipe friction and heat loss formulations are non-linear. In order to find the optimal district heating network configuration, genetic algorithm which handles the mixed integer nonlinear programming problem is chosen. The network configuration is represented with binary and integer encoding and is optimized in terms of the net present cost. The optimization results indicates that the optimal DH network configuration is determined by multiple factors such as the consumer heating load, the distance between the heating plant to the consumer, the design criteria regarding the pressure and temperature limitation, as well as the corresponding network heat loss.

  18. Design and optimisation of novel configurations of stormwater constructed wetlands

    Science.gov (United States)

    Kiiza, Christopher

    2017-04-01

    Constructed wetlands (CWs) are recognised as a cost-effective technology for wastewater treatment. CWs have been deployed and could be retrofitted into existing urban drainage systems to prevent surface water pollution, attenuate floods and act as sources for reusable water. However, there exist numerous criteria for design configuration and operation of CWs. The aim of the study was to examine effects of design and operational variables on performance of CWs. To achieve this, 8 novel designs of vertical flow CWs were continuously operated and monitored (weekly) for 2years. Pollutant removal efficiency in each CW unit was evaluated from physico-chemical analyses of influent and effluent water samples. Hybrid optimised multi-layer perceptron artificial neural networks (MLP ANNs) were applied to simulate treatment efficiency in the CWs. Subsequently, predictive and analytical models were developed for each design unit. Results show models have sound generalisation abilities; with various design configurations and operational variables influencing performance of CWs. Although some design configurations attained faster and higher removal efficiencies than others; all 8 CW designs produced effluents permissible for discharge into watercourses with strict regulatory standards.

  19. Combining configurational energies and forces for molecular force field optimization

    Science.gov (United States)

    Vlcek, Lukas; Sun, Weiwei; Kent, Paul R. C.

    2017-10-01

    While quantum chemical simulations have been increasingly used as an invaluable source of information for atomistic model development, the high computational expenses typically associated with these techniques often limit thorough sampling of the systems of interest. It is therefore of great practical importance to use all available information as efficiently as possible, and in a way that allows for consistent addition of constraints that may be provided by macroscopic experiments. Here we propose a simple approach that combines information from configurational energies and forces generated in a molecular dynamics simulation to increase the effective number of samples. Subsequently, this information is used to optimize a molecular force field by minimizing the statistical distance similarity metric. We illustrate the methodology on an example of a trajectory of configurations generated in equilibrium molecular dynamics simulations of argon and water and compare the results with those based on the force matching method.

  20. Virtual display design using waveguide hologram in conical mounting configuration

    Science.gov (United States)

    Yan, Zhanjun; Li, Wenqiang; Zhou, Yongjun; Kang, Mingwu; Zheng, Zhenrong

    2011-09-01

    An improved virtual display is proposed by using a waveguide holographic configuration with two total internal reflection holographic gratings in conical mounting and two volume hologram in classical mounting recorded on a single transparent planar waveguide. Using this compact configuration, efficiency can be dramatically improved and assembly is easy to be realized. The main principle and the method of intensity uniformity control are present in the paper. The analysis and simulation results are also explained. The virtual display system design shows good optical performance with 25 deg. field of view, a large pupil about 43 mm, little distortion less than 1%, and low aberration. The configuration can be used to a portable or wearable display.

  1. Configuration Design of Novel Manually Operated Dynamo Flashlights

    Science.gov (United States)

    Yan, Hong-Sen; Wang, Hsin-Te

    This paper synthesizes novel configurations of manually operated dynamo flashlights. Topology and motion characteristics of existing gear dynamos are modified and concluded. The structural sketches and corresponding graph representations for gear trains and dynamos with the defined induced magnetic circuits are defined. Through the concepts of generalization and specialization, the atlas of the structural sketches and graphs of the embedded gear dynamos is obtained subject to the defined design requirements and constraints. And, a systematic approach is proposed to synthesize the novel mechanisms of the embedded gear dynamos. As a result, the embedded three-link and four-link gear dynamos have 12 and 24 novel design configurations, respectively. One prototype of the embedded three-link and another of the embedded four-link gear dynamo are built.

  2. Blueprinting Crowdfunding - Designing a Crowdfunding Service Configuration Framework

    OpenAIRE

    Haas, Philipp; Blohm, Ivo

    2017-01-01

    Crowdfunding gained momentum over the last few years. In contrast to traditional forms of funding, the service provision of crowdfunding platforms is performed within service systems. These comprise a complex combination of IT and non-IT services, different stakeholders, and diverging contexts and purposes. The design and operation of such service systems represents a tough challenge. Therefore, we developed a crowdfunding service configuration framework in the form of a morphological box and...

  3. Integrated Energy Design

    DEFF Research Database (Denmark)

    Brunsgaard, Camilla; Dvořáková, Pavla; Wyckmans, Annemie

    2014-01-01

    In Europe, energy and climate policies started to take shape from the 1990s onwards culminating with the ambitious 20e20e20 climate goals and the Low-Carbon Europe roadmap 2050. The European Commission empower the importance of achieving the objective of the recast Directive on energy performance...... of buildings (EPBD) that new buildings built from 2021 onwards will have to be nearly zeroenergy buildings. The general belief is that the energy performance optimization of buildings requires an integrated design approach and cross-disciplinary teamwork to optimize the building’s energy use and quality...

  4. Energy-efficient photobioreactor configuration for algal biomass production.

    Science.gov (United States)

    Pegallapati, Ambica Koushik; Arudchelvam, Yalini; Nirmalakhandan, Nagamany

    2012-12-01

    An internally illuminated photobioreactor (IIPBR) design is proposed for energy-efficient biomass production. Theoretical rationale of the IIPBR design and its advantages over the traditional bubble column photobioreactors (PBRs) are presented, followed by experimental results from prototype scale cultivation of freshwater and marine algal strains in an 18L IIPBR. Based on theoretical considerations, the proposed IIPBR design has the potential to support 160% higher biomass density and higher biomass productivity per unit energy input, B/E, than a bubble column PBR of equal incident area per unit culture volume. Experimental B/E values recorded in this study with fresh water algae and marine algae (1.42 and 0.37 gW(-1)d(-1), respectively) are at least twice as those reported in the literature for comparable species cultivated in bubble column and airlift PBRs. Copyright © 2012 Elsevier Ltd. All rights reserved.

  5. Building a design community for sustainable homes through configuration and open innovation

    DEFF Research Database (Denmark)

    Thuesen, Christian Langhoff; Jespersen, Kristina Risom

    2009-01-01

    is a configurator where the users based on the produceres templates can design their own home at a selected address visualizing and estimating the energy consumption, total cost, CO2 emission etc. All the designs will be collected and rated in a design space creating transparency over the market and technologies....... Furthermore will an idea space collect and rate ideas from the users. Through a combination of technical and user driven innovation the design community will act as a learning tool for the users and producers and thereby facilitate the development of a market for sustainable homes....

  6. Study and Design of Spiral Bent Waveguide Configuration

    Institute of Scientific and Technical Information of China (English)

    ZENG Wen-hong; LIAO Yun; SHI Shuang-jin; QIU Qi; LI Wei

    2007-01-01

    A new version of the scalar transverse electric(TE) wave equation in the bent waveguide is introduced.Then,TE polarized field in curved single-mode waveguides is analyzed by using the finite-difference beam propagation method(FD-BPM).The bending loss in bent waveguides is gotten for the optical fields obtained from BPM and comparisons are made among losses of the waveguides with various curvature radiuses,refractive index differences and cross sections.Based on the results,the design of spiral bent waveguide configuration is proposed as follows:refractive index difference being of 0.007,both width and thickness of waveguides being of 6 μm,the curvature radius in the spiral centre being of 4 mm,and the bending loss coefficient of the designed spiral bent waveguide being of 0.302 3 dB/cm.

  7. A rotational compressible inverse design method for internal flow configurations

    Science.gov (United States)

    Dedoussis, V.; Chaviaropoulos, P.; Papailiou, K. D.

    The development of a rotational inviscid compressible inverse design method for two-dimensional internal flow configurations is described. Rotationality is due to an incoming entropy gradient, while total enthalpy is considered to be constant throughout the flowfield. The method is based on the potential function-streamfunction formulation. A novel procedure based on differential geometry arguments is employed to derive the governing equation for velocity by requiring the curvature of the two-dimensional Euclidean space to be zero. The velocity equation solved in conjunction with a transport equation for a thermal drift function provide the flowfield without any geometry feedback. An auxiliary orthogonal computational grid adapted to the solution is employed. Geometry is determined by integrating Frenet equations of the grid lines. Inverse calculation results are compared with results of direct reproduction calculations.

  8. The optimum design configurations of savonius wind turbines

    Science.gov (United States)

    Ushiyama, I.; Nagai, H.; Mino, M.

    The results of wind tunnel and water channel trials to optimize the Savonius rotor windmill are reported. The design simplicity, omnidirectional wind acceptance, self-starting characteristics, and lack of a need for overspeed control encouraged the tests. The rotor aspect ratio, blade overlap, blade separation gap, the blade cross-section profile, and the guide vane attachment were investigated, together with the flow pattern through the blades. Two-bladed semicircular and Bach type configurations were examined. Every factor was found to significantly affect performance, and the Bach blades with a 30-50% overlap and no blade separation were determined to be effective. Inclusion of separation gap degraded performance. High aspect ratios are favored for high wind velocity regions, while low aspect ratios are preferable in regions with low winds. Guide vanes augmented the power coefficient, which approached 0.35 at 4 m/s.

  9. Lessons Learned in Designing User-configurable Modular Robotics

    DEFF Research Database (Denmark)

    Lund, Henrik Hautop

    2013-01-01

    User-configurable robotics allows users to easily configure robotic systems to perform task-fulfilling behaviors as desired by the users. With a user configurable robotic system, the user can easily modify the physical and func-tional aspect in terms of hardware and software components of a robotic...... with the semi-autonomous com-ponents of the user-configurable robotic system in interaction with the given environment. Components constituting such a user-configurable robotic system can be characterized as modules in a modular robotic system. Several factors in the definition and implementation...

  10. Designing consultancy on energy

    Energy Technology Data Exchange (ETDEWEB)

    Nielsen, Lene [Danish Energy Authority, Copenhagen (Denmark)

    2005-07-01

    There is a wide tradition for using energy consultancy in all end-using sectors and in various models. A lot of aspects have to be taken into consideration when a consultant scheme is to be launched. This paper will contribute to the discussion of the role of the consultant in the different energy end-use sectors: Energy consultancy is defined. The process for energy consulting is related to the eight fundamental objectives for effective management consulting (Arthur N. Turner): responding to a client's request for information; providing solutions to specific problems; giving an in-depth, accurate diagnosis; presenting a program of recommended corrective actions; implementing changes; building consensus and commitment; facilitating client learning; and enhancing organizational effectiveness. The role of the consultant is divided into 4 categories (expert, diagnostician, sparring partner, process consultant) depending on the consultant's focus (process or cases) and methodology (analysis or dialogue). Designing energy consultancy should reflect the end-use sector (household, industry etc.)

  11. High Energy Electron Confinement in a Magnetic Cusp Configuration

    CERN Document Server

    Park, Jaeyoung; Sieck, Paul E; Offermann, Dustin T; Skillicorn, Michael; Sanchez, Andrew; Davis, Kevin; Alderson, Eric; Lapenta, Giovanni

    2014-01-01

    We report experimental results validating the concept that plasma confinement is enhanced in a magnetic cusp configuration when beta (plasma pressure/magnetic field pressure) is order of unity. This enhancement is required for a fusion power reactor based on cusp confinement to be feasible. The magnetic cusp configuration possesses a critical advantage: the plasma is stable to large scale perturbations. However, early work indicated that plasma loss rates in a reactor based on a cusp configuration were too large for net power production. Grad and others theorized that at high beta a sharp boundary would form between the plasma and the magnetic field, leading to substantially smaller loss rates. The current experiment validates this theoretical conjecture for the first time and represents critical progress toward the Polywell fusion concept which combines a high beta cusp configuration with an electrostatic fusion for a compact, economical, power-producing nuclear fusion reactor.

  12. High-energy terahertz wave parametric oscillator with a surface-emitted ring-cavity configuration.

    Science.gov (United States)

    Yang, Zhen; Wang, Yuye; Xu, Degang; Xu, Wentao; Duan, Pan; Yan, Chao; Tang, Longhuang; Yao, Jianquan

    2016-05-15

    A surface-emitted ring-cavity terahertz (THz) wave parametric oscillator has been demonstrated for high-energy THz output and fast frequency tuning in a wide frequency range. Through the special optical design with a galvano-optical scanner and four-mirror ring-cavity structure, the maximum THz wave output energy of 12.9 μJ/pulse is achieved at 1.359 THz under the pump energy of 172.8 mJ. The fast THz frequency tuning in the range of 0.7-2.8 THz can be accessed with the step response of 600 μs. Moreover, the maximum THz wave output energy from this configuration is 3.29 times as large as that obtained from the conventional surface-emitted THz wave parametric oscillator with the same experimental conditions.

  13. Energy-aware design of digital systems

    Energy Technology Data Exchange (ETDEWEB)

    Gruian, F.

    2000-02-01

    Power and energy consumption are important issues in many digital applications, for reasons such as packaging cost and battery life-span. With the development of portable computing and communication, an increasing number of research groups are addressing power and energy related issues at various stages during the design process. Most of the work done in this area focuses on lower abstraction levels, such as gate or transistor level. Ideally, a power and energy-efficient design flow should consider the power and energy issues at every stage in the design process. Therefore, power and energy aware methods, applicable early in the design process are required. In this trend, the thesis presents two high-level design methods addressing power and energy consumption minimization. The first of the two approaches we describe, targets power consumption minimization during behavioral synthesis. This is carried out by minimizing the switching activity, while taking the correlations between signals into account. The second approach performs energy consumption minimization during system-level design, by choosing the most energy-efficient schedule and configuration of resources. Both methods make use of the constraint programming paradigm to model the problems in an elegant manner. The experimental results presented in this thesis show the impact of addressing the power and energy related issues early in the design process.

  14. District Heating Network Design and Configuration Optimization with Genetic Algorithm

    DEFF Research Database (Denmark)

    Li, Hongwei; Svendsen, Svend

    2013-01-01

    and the pipe friction and heat loss formulations are non-linear. In order to find the optimal district heating network configuration, genetic algorithm which handles the mixed integer nonlinear programming problem is chosen. The network configuration is represented with binary and integer encoding...

  15. Optical fiber configurations for transmission of laser energy over great distances

    Science.gov (United States)

    Rinzler, Charles C; Zediker, Mark S

    2013-10-29

    There are provided optical fiber configurations that provide for the delivery of laser energy, and in particular, the transmission and delivery of high power laser energy over great distances. These configurations further are hardened to protect the optical fibers from the stresses and conditions of an intended application. The configurations provide means for determining the additional fiber length (AFL) need to obtain the benefits of such additional fiber, while avoiding bending losses.

  16. Optical fiber configurations for transmission of laser energy over great distances

    Energy Technology Data Exchange (ETDEWEB)

    Rinzler, Charles C; Zediker, Mark S

    2014-11-04

    There are provided optical fiber configurations that provide for the delivery of laser energy, and in particular, the transmission and delivery of high power laser energy over great distances. These configurations further are hardened to protect the optical fibers from the stresses and conditions of an intended application. The configurations provide means for determining the additional fiber length (AFL) need to obtain the benefits of such additional fiber, while avoiding bending losses.

  17. Energy of Long-Lifetime Configurations in Zero-Temperature Dynamics

    Institute of Scientific and Technical Information of China (English)

    RONG Yong-Hui; KONG Xiang-Mu

    2009-01-01

    Using Monte Carlo method with zero-temperature dynamics, we investigate energy evolution of Ising spin configuration on a square lattice.The energies of some configurations exhibit long duration before those configurations reach the final state -- ground state or frozen stripe state.For ground-state dynamical realization, the duration occurs when the energy per spin is 4/L, where L is the lattice size.For stripe-state dynamical realization, the energy is slightly higher than 2/ L when the duration appears in the last evolution stage.In addition, it is found that the average energy per spin in final state is approximately 2/3L.

  18. A divertor plasma configuration design method for tokamaks

    Science.gov (United States)

    Guo, Yong; Xiao, Bing-Jia; Liu, Lei; Yang, Fei; Wang, Yuehang; Qiu, Qinglai

    2016-11-01

    The efficient and safe operation of large fusion devices strongly relies on the plasma configuration inside the vacuum chamber. It is important to construct the proper plasma equilibrium with a desired plasma configuration. In order to construct the target configuration, a shape constraint module has been developed in the tokamak simulation code (TSC), which controls the poloidal flux and the magnetic field at several defined control points. It is used to construct the double null, lower single null, and quasi-snowflake configurations for the required target shape and calculate the required PF coils current. The flexibility and practicability of this method have been verified by the simulated results. Project supported by the National Magnetic Confinement Fusion Research Program of China (Grant Nos. 2014GB103000 and 2014GB110003), the National Natural Science Foundation of China (Grant Nos. 11305216, 11305209, and 11375191), and External Cooperation Program of BIC, Chinese Academy of Sciences (Grant No. GJHZ201303).

  19. Design and Optimisation of Fuel Tanks for BWB Configurations

    Directory of Open Access Journals (Sweden)

    Goraj Zdobyslaw

    2016-12-01

    Full Text Available This paper describes assumptions, goals, methods, results and conclusions related to fuel tank arrangement of a flying wing passenger airplane configuration. A short overview of various fuel tank systems in use today of different types of aircraft is treated as a starting point for designing a fuel tank system to be used on very large passenger airplanes. These systems may be used to move fuel around the aircraft to keep the centre of gravity within acceptable limits, to maintain pitch and lateral balance and stability. With increasing aircraft speed, the centre of lift moves aft, and for trimming the elevator or trimmer must be used thereby increasing aircraft drag. To avoid this, the centre of gravity can be shifted by pumping fuel from forward to aft tanks. The lesson learnt from this is applied to minimise trim drag by moving the fuel along the airplane. Such a task can be done within coming days if we know the minimum drag versus CG position and weight value. The main part of the paper is devoted to wing bending moment distribution. A number of arrangements of fuel in airplane tanks are investigated and a scenario of refuelling - minimising the root bending moments - is presented. These results were obtained under the assumption that aircraft is in long range flight (14 hours, CL is constant and equal to 0.279, Specific Fuel Consumption is also constant and that overall fuel consumption is equal to 20 tons per 1 hour. It was found that the average stress level in wing structure is lower if refuelling starts from fuel tanks located closer to longitudinal plane of symmetry. It can influence the rate of fatigue.

  20. Energy Optimized Configuration of Concrete Element with PCM

    DEFF Research Database (Denmark)

    Pomianowski, Michal Zbigniew

    The building sector accounts for approximately 40% of the world’s total use of primary energy, and the majority of this energy is used to maintain satisfactory indoor climate conditions by heating, cooling and ventilation. Further on, traditional energy sources are irretrievably decreasing...... and the price of energy and fuel is gradually increasing. On top of that, the gas emissions to the atmosphere cause long-term and hazardous changes to the global climate. As a response to that, countries started to enforce new, more demanding legislations and standards for the newly constructed and renovated...... buildings. For example, in Denmark the new energy frames assume a reduction of primary energy use for buildings of respectively 25% in 2010, 50% in 2015 and 75% in 2020 compared to year 2006 figures. As a consequence, the building sector has to be equipped with the new technologies that would enable...

  1. Supersonic Aerodynamic Design Improvements of an Arrow-Wing HSCT Configuration Using Nonlinear Point Design Methods

    Science.gov (United States)

    Unger, Eric R.; Hager, James O.; Agrawal, Shreekant

    1999-01-01

    This paper is a discussion of the supersonic nonlinear point design optimization efforts at McDonnell Douglas Aerospace under the High-Speed Research (HSR) program. The baseline for these optimization efforts has been the M2.4-7A configuration which represents an arrow-wing technology for the High-Speed Civil Transport (HSCT). Optimization work on this configuration began in early 1994 and continued into 1996. Initial work focused on optimization of the wing camber and twist on a wing/body configuration and reductions of 3.5 drag counts (Euler) were realized. The next phase of the optimization effort included fuselage camber along with the wing and a drag reduction of 5.0 counts was achieved. Including the effects of the nacelles and diverters into the optimization problem became the next focus where a reduction of 6.6 counts (Euler W/B/N/D) was eventually realized. The final two phases of the effort included a large set of constraints designed to make the final optimized configuration more realistic and they were successful albeit with a loss of performance.

  2. District Heating Network Design and Configuration Optimization with Genetic Algorithm

    DEFF Research Database (Denmark)

    Li, Hongwei; Svendsen, Svend

    2011-01-01

    the heating plant location is allowed to vary. The connection between the heat generation plant and the end users can be represented with mixed integer and the pipe friction and heat loss formulations are non-linear. In order to find the optimal DH distribution pipeline configuration, the genetic algorithm...

  3. District Heating Network Design and Configuration Optimization with Genetic Algorithm

    DEFF Research Database (Denmark)

    Li, Hongwei; Svendsen, Svend

    2011-01-01

    the heating plant location is allowed to vary. The connection between the heat generation plant and the end users can be represented with mixed integer and the pipe friction and heat loss formulations are non-linear. In order to find the optimal DH distribution pipeline configuration, the genetic algorithm...

  4. Electrode contact configuration and energy consumption in spinal cord stimulation

    NARCIS (Netherlands)

    Vos, de Cecile C.; Hilgerink, Marjolein P.; Buschman, Hendrik P.J.; Holsheimer, Jan

    2009-01-01

    Objective: To test the hypothesis that in spinal cord stimulation, in contrast to an increase of the number of anodes which reduces energy consumption per pulse, an increase of the number of cathodes raises the energy per pulse. Methods: Patients with an Itrel 3 pulse generator and a Pisces Quad qu

  5. Using a Configuration System to Design Toilets and Place Installation Shafts

    DEFF Research Database (Denmark)

    Kudsk, Anders; Hvam, Lars; Thuesen, Christian Langhoff

    2013-01-01

    The aim of this research is to discover how configuration systems can support a product's design process when a high degree of variation is required and a very open or endless space exists for possible configurations. The article is based on an industrial case involving a firm that wishes to offer...... a bathroom configurator to architects. The aim of the configurator is to help architects design a bathroom according to relevent requirements and norms. In offering the configurator, the firm aims to enable a design that can be coordinated with a prefabricated installation shaft sold by the firm, and also...... to create customer leads. Four scenarios are developed for how design can be supported by four different types of configuration technologies. The four scenarios are evaluated in relation to a number of functional and technical requirements. The scenarios indicate that a good and varied range...

  6. Energy Optimized Configuration of Concrete Element with PCM

    DEFF Research Database (Denmark)

    Pomianowski, Michal Zbigniew

    cases result in poorer heat storage and cooling power performances than initially expected. Results from the full-scale investigation of dynamic heat storage capacity of decks indicated that there is no substantial difference between decks with extended heat transfer surface and one with an ordinary......The building sector accounts for approximately 40% of the world’s total use of primary energy, and the majority of this energy is used to maintain satisfactory indoor climate conditions by heating, cooling and ventilation. Further on, traditional energy sources are irretrievably decreasing...... and the price of energy and fuel is gradually increasing. On top of that, the gas emissions to the atmosphere cause long-term and hazardous changes to the global climate. As a response to that, countries started to enforce new, more demanding legislations and standards for the newly constructed and renovated...

  7. Effect of Radial Density Configuration on Wave Field and Energy Flow in Axially Uniform Helicon Plasma

    Science.gov (United States)

    Chang, Lei; Li, Qingchong; Zhang, Huijie; Li, Yinghong; Wu, Yun; Zhang, Bailing; Zhuang, Zhong

    2016-08-01

    The effect of the radial density configuration in terms of width, edge gradient and volume gradient on the wave field and energy flow in an axially uniform helicon plasma is studied in detail. A three-parameter function is employed to describe the density, covering uniform, parabolic, linear and Gaussian profiles. It finds that the fraction of power deposition near the plasma edge increases with density width and edge gradient, and decays in exponential and “bump-on-tail” profiles, respectively, away from the surface. The existence of a positive second-order derivative in the volume density configuration promotes the power deposition near the plasma core, which to our best knowledge has not been pointed out before. The transverse structures of wave field and current density remain almost the same during the variation of density width and gradient, confirming the robustness of the m=1 mode observed previously. However, the structure of the electric wave field changes significantly from a uniform density configuration, for which the coupling between the Trivelpiece-Gould (TG) mode and the helicon mode is very strong, to non-uniform ones. The energy flow in the cross section of helicon plasma is presented for the first time, and behaves sensitive to the density width and edge gradient but insensitive to the volume gradient. Interestingly, the radial distribution of power deposition resembles the radial profile of the axial component of current density, suggesting the control of the power deposition profile in the experiment by particularly designing the antenna geometry to excite a required axial current distribution. supported by National Natural Science Foundation of China (No. 11405271)

  8. Weak Coupling Casimir Energies for Finite Plate Configurations

    CERN Document Server

    Wagner, Jef; Parashar, Prachi

    2008-01-01

    We derive and use an extremely simplified formula for the interaction Casimir energy for two separate bodies in the weak coupling regime for massless scalar fields. We derive closed form solutions for a general arrangement of two $\\delta$-function plates finite in one direction and infinite in another. We examine the situation of two parallel plates finite in both transverse directions.

  9. Excitation-energy influence at the scission configuration

    Directory of Open Access Journals (Sweden)

    Ramos D.

    2017-01-01

    Full Text Available Transfer- and fusion-induced fission in inverse kinematics was proven to be a powerful tool to investigate nuclear fission, widening the information of the fission fragments and the access to unstable fissioning systems with respect to other experimental approaches. An experimental campaign for fission investigation has being carried out at GANIL with this technique since 2008. In these experiments, a beam of 238U, accelerated to 6.1 MeV/u, impinges on a 12C target. Fissioning systems from U to Cf are populated through transfer and fusion reactions, with excitation energies that range from few MeV up to 46 MeV. The use of inverse kinematics, the SPIDER telescope, and the VAMOS spectrometer permitted the characterization of the fissioning system in terms of mass, nuclear charge, and excitation energy, and the isotopic identification of the full fragment distribution. The neutron excess, the total neutron multiplicity, and the even-odd staggering in the nuclear charge of fission fragments are presented as a function of the excitation energy of the fissioning system. Structure effects are observed at Z∼50 and Z∼55, where their impact evolves with the excitation energy.

  10. Systems design analysis applied to launch vehicle configuration

    Science.gov (United States)

    Ryan, R.; Verderaime, V.

    1993-01-01

    As emphasis shifts from optimum-performance aerospace systems to least lift-cycle costs, systems designs must seek, adapt, and innovate cost improvement techniques in design through operations. The systems design process of concept, definition, and design was assessed for the types and flow of total quality management techniques that may be applicable in a launch vehicle systems design analysis. Techniques discussed are task ordering, quality leverage, concurrent engineering, Pareto's principle, robustness, quality function deployment, criteria, and others. These cost oriented techniques are as applicable to aerospace systems design analysis as to any large commercial system.

  11. TECHNOLOGY AND APPLICATION OF PRODUCT EVOLUTIONARY DESIGN BASED ON CONFIGURATION IN MASS CUSTOMIZATION MODE

    Institute of Scientific and Technical Information of China (English)

    FENG Yixiong; CHENG Jin; TAN Jianrong; ZHENG Bing; WEI Zhe

    2007-01-01

    Product customization has been recognized as an effective means to implement mass customization (MC). A new theory and method for MC-oriented evolutionary design of configuration product is presented based on the study of developing law of evolutionary design in integrated environment, which focuses on the innovation and reuse properties of configuration product. The key technologies for general requirement modeling in quick response to customer requirement, multi-level stepwise configuration optimization driven by customer requirement and evolutionary deduction of product variable structure based on configuration association are thoroughly investigated. The successful application of the presented method in the development of real-life products demonstrates its utility, flexibility and robusticity.

  12. Recent Advances in the Design of Quasi-axisymmetric Stellarator Plasma Configurations

    Energy Technology Data Exchange (ETDEWEB)

    Reiman, A.; Ku, L.; Monticello, D.; Hirschman, S.; Hudson, S.; Kessel, C. [and others

    2001-01-30

    Strategies for the improvement of quasi-axisymmetric stellarator configurations are explored. Calculations of equilibrium flux surfaces for candidate configurations are also presented. One optimization strategy is found to generate configurations with improved neoclassical confinement, simpler coils with lower current density, and improved flux surface quality relative to previous designs. The flux surface calculations find significant differences in the extent of islands and stochastic regions between candidate configurations. (These calculations do not incorporate the predicted beneficial effects of perturbed bootstrap currents.) A method is demonstrated for removing low-order islands from candidate configurations by relatively small modifications of the configuration. One configuration is identified as having particularly desirable properties for a proposed experiment.

  13. Energy Optimized Configuration of Concrete Element with PCM

    DEFF Research Database (Denmark)

    Pomianowski, Michal Zbigniew

    and the price of energy and fuel is gradually increasing. On top of that, the gas emissions to the atmosphere cause long-term and hazardous changes to the global climate. As a response to that, countries started to enforce new, more demanding legislations and standards for the newly constructed and renovated...... investigates the potential of combining the microencapsulated phase change material (PCM) in the hollow core concrete deck element in order to increase the dynamic heat storage capacity of the internal envelope of the multi-storey buildings. Moreover, the study investigates the cooling capacity and performance...... to standard concrete deck element. These results, however, were unexpected since the material properties of mortar used to cast tiles were determined to be worse than those of concrete material used to cast standard decks....

  14. A Case Retrieval Projection Pursuit Model for Configuration Design of a Product Family%A Case Retrieval Projection Pursuit Model for Configuration Design of a Product Family

    Institute of Scientific and Technical Information of China (English)

    XU Zi-rong; ZHANG Yi-fei

    2011-01-01

    The paper studies on case-based reasoning of uncertain product attributes in configuration design of a product family. Interval numbers characterize uncertain product attributes. By interpolating a number of certain values randomly to replace interval numbers and making projection pursuit analysis on source cases and target cases of expanded numbers, we can get a projection value in the optimal projection direction. Based on projection value, we can construct a case retrieval model of projection pursuit that can handle coexisting certain and uncertain product attributes. The application examples of chainsaw configuration design show that case retrieval is highly sensitive to reliable results.

  15. Energy Optimized Configuration of Concrete Element with PCM

    DEFF Research Database (Denmark)

    Pomianowski, Michal Zbigniew

    with specially designed ventilation inlet slot diffuser. Firstly, it was observed that the assumptions regarding the theoretical thermal properties stand out from the experimentally determined thermal properties of the PCM concrete. Consequently, the results obtained from the initial (theoretical) and updated...... investigates the potential of combining the microencapsulated phase change material (PCM) in the hollow core concrete deck element in order to increase the dynamic heat storage capacity of the internal envelope of the multi-storey buildings. Moreover, the study investigates the cooling capacity and performance...... of the concrete deck with PCM and integrated TABS and highlights limitations and challenges of the new technology. The presented work utilizes numerical methods to study the dynamic performance of the new product developed. Consequently, the experimental set-ups and methodologies are developed firstly...

  16. Novel design configurations for permanent magnet wind generators

    Science.gov (United States)

    Chen, Yicheng

    2004-12-01

    The aim of this research is to search for optimal designs of permanent magnet (PM) wind generators of different topologies. The dissertation deals with the development of analytical design equations and formulas for PM wind generators of different topologies, including equivalent magnetic circuit model for magnets, calculation of leakage flux, influence of d-q axis armature reaction, flux waveform analysis, as well as performance verification. 3-D and simplified 2-D finite element analysis is used to enhance the design precision, by which analytical formulas are modified. A new and improved formula is proposed for lamination loss calculations, based on a large experimental data set provided by steel manufacturers. The temperature stability of NdFeB magnets is analyzed and some proposals for eliminating irreversible demagnetization are presented. Two existing experimental machines are used to validate the design equations. The genetic algorithms are used to investigate the multi-objective design optimization of PM wind generators for a high efficiency and light-weight design. The reasoning behind the selection of the objective functions, design variables and constraints are given as guidance for the PM wind generator optimum design. The implementation of the genetic algorithm is also given. A comparison of PM wind generators of different topologies is presented. Conclusions are drawn for topology selections of PM wind generators. The group of soft magnetic composites (SMC) has recently been expanded by the introduction of new materials with significantly improved frequency properties. This has made SMC a viable alternative to steel laminations for a range of new applications, especially axial-flux wind generators. The isotropic nature of the SMC combined with the unique shaping possibilities opens up new design solutions for axial-flux wind generators. Through careful design, an axial-flux PM wind generator with SMC core is built and tested, demonstrating the

  17. Design of a shock-induced combustion experiment in an axisymmetric configuration with hydrogen injection

    NARCIS (Netherlands)

    Verreault, J.; DeChamplain, A.; Mayer, A.E.H.J.; Veraar, R.G.; Stowe, R.A.; Farinaccio, R.; Harris, P.G.

    2007-01-01

    This work presents a design for a shock-induced combustion experiment using a two-angle cone configuration. Three injector geometries were considered: a cone surface, a dual stage configuration with rectangular gaps (DSRG) and a cylindrical ramp (CR). Four parameters were investigated: the

  18. Design of a shock-induced combustion experiment in an axisymmetric configuration with hydrogen injection

    NARCIS (Netherlands)

    Verreault, J.; DeChamplain, A.; Mayer, A.E.H.J.; Veraar, R.G.; Stowe, R.A.; Farinaccio, R.; Harris, P.G.

    2007-01-01

    This work presents a design for a shock-induced combustion experiment using a two-angle cone configuration. Three injector geometries were considered: a cone surface, a dual stage configuration with rectangular gaps (DSRG) and a cylindrical ramp (CR). Four parameters were investigated: the penetrati

  19. Configuration System for Simulation Based Design of Vibratory Bowl Feeders

    DEFF Research Database (Denmark)

    Hansson, Michael; Mathiesen, Simon; Ellekilde, Lars-Peter;

    2016-01-01

    Vibratory bowl feeders are still among the most commonly used production equipment for automated part feeding, where parts are correctly oriented for further manipulation by being conveyed through a set of orienting devices. Designing vibratory bowl feeders involves selecting and sequencing a num...

  20. Analysis of Energy Demand for Low-Energy Multi-Dwelling Buildings of Different Configuration

    Directory of Open Access Journals (Sweden)

    Giedrė Streckienė

    2014-10-01

    Full Text Available To meet the goals established by Directive 2010/31/EU of the European Parliament and of the Council on the energy performance of buildings, the topics of energy efficiency in new and old buildings must be solved. Research and development of new energy solutions and technology are necessary for increasing energy performance of buildings. Three low-energy multi-dwelling buildings have been modelled and analyzed in the presented study. All multi-dwelling houses are made of similar single-family house cells. However, multi-dwelling buildings are of different geometry, flat number and height. DesignBuilder software was used for simulating and determining heating, cooling and electricity demand for buildings. Three different materials (silicate, ceramic and clay concrete blocks as bearing constructions of external walls have been analyzed. To decrease cooling demand for buildings, the possibility of mounting internal or external louvers has been considered. Primary energy savings for multi-dwelling buildings using passive solar measures have been determined.

  1. MS S4.03.002 - Adjoint-Based Design for Configuration Shaping

    Science.gov (United States)

    Nemec, Marian; Aftosmis, Michael J.

    2009-01-01

    This slide presentation discusses a method of inverse design for low sonic boom using adjoint-based gradient computations. It outlines a method for shaping a configuration in order to match a prescribed near-field signature.

  2. Global Supply Chain Design : Exploring configurational and coordination factors

    OpenAIRE

    Abid, Muhammad

    2015-01-01

    This thesis addresses the topic of global supply chain design. One major challenge concerns how to manage the tension between separation and integration pertaining to the localization of business activities. In this regard Ferdows (2008) worked to create two new production network models (rooted production network and footloose production network). Earlier studies have highlighted the choices that are involved in the network of facilities but lack in providing a comprehensive picture in terms...

  3. Highly configurable low cost remote laboratory with integrated support for learning – Hardware design

    OpenAIRE

    Dag A. H. Samuelsen; Olaf H. Graven

    2013-01-01

    This paper presents a flexible and low cost design specification for a remote laboratory platform for electronics laboratories. The system utilises a motherboard design and this paper presents both the design of the motherboard, various designs for add on cards and shows how to configure the setup. The design is focused on providing the user with a combination of easy setup and a large freedom in reconfiguration all provided as a low cost solution. The solution is designed to facilitate a nat...

  4. Operational concepts and implementation strategies for the design configuration management process.

    Energy Technology Data Exchange (ETDEWEB)

    Trauth, Sharon Lee

    2007-05-01

    This report describes operational concepts and implementation strategies for the Design Configuration Management Process (DCMP). It presents a process-based systems engineering model for the successful configuration management of the products generated during the operation of the design organization as a business entity. The DCMP model focuses on Pro/E and associated activities and information. It can serve as the framework for interconnecting all essential aspects of the product design business. A design operation scenario offers a sense of how to do business at a time when DCMP is second nature within the design organization.

  5. Configuration Method Design for Reconfigurable Manufacturing System with the aid of Plant Simulation

    DEFF Research Database (Denmark)

    Li, Yang; Zhang, Shuai; Bilberg, Arne

    2014-01-01

    A new Reconfigurable Manufacturing System structure has been recently designed by a large consumer goods manufacturer in Europe, aiming to balance the performance of productivity and flexibility. This article shows an exploratory research on the (re)configuration procedure of the new RMS structure....... Following the procedure which is designed in this paper, the (re)configuration of RMS can be managed as part of the daily operation with the help of computer simulation. Keywords: Plant Simulation, Tecnomatix, Reconfigurable Manufacturing System, modular manufacturing....

  6. Designing with Space Syntax: A configurative approach to architectural layout, proposing a computational methodology

    NARCIS (Netherlands)

    Nourian, P.; Rezvani, S.; Sariyildiz, I.S.

    2013-01-01

    This paper introduces a design methodology and a toolkit developed as a parametric CAD program for configurative design of architectural plan layouts. Using this toolkit, designers can start plan layout process with sketching the way functional spaces need to connect to each other. A tool draws an i

  7. Mars Rover Sample Return aerocapture configuration design and packaging constraints

    Science.gov (United States)

    Lawson, Shelby J.

    1989-01-01

    This paper discusses the aerodynamics requirements, volume and mass constraints that lead to a biconic aeroshell vehicle design that protects the Mars Rover Sample Return (MRSR) mission elements from launch to Mars landing. The aerodynamic requirements for Mars aerocapture and entry and packaging constraints for the MRSR elements result in a symmetric biconic aeroshell that develops a L/D of 1.0 at 27.0 deg angle of attack. A significant problem in the study is obtaining a cg that provides adequate aerodynamic stability and performance within the mission imposed constraints. Packaging methods that relieve the cg problems include forward placement of aeroshell propellant tanks and incorporating aeroshell structure as lander structure. The MRSR missions developed during the pre-phase A study are discussed with dimensional and mass data included. Further study is needed for some missions to minimize MRSR element volume so that launch mass constraints can be met.

  8. Wavefunction and energy of the 1s22sns configuration in a beryllium atom

    Institute of Scientific and Technical Information of China (English)

    Huang Shi-Zhong; Ma Kun; Yu Jia-Ming; Liu Fen

    2008-01-01

    A new set of trial functions for 1s22sns configurations in a beryllium atom is suggested.A Mathematica program baaed on the variational method is developed to calculate the wavefunctions and energies of 1s22sns (n=3-6)configurations in a beryllium atom.Non-relativistic energy,polarization correction and relativistic correction which include mass correction,one- and two-body Darwin corrections,spin-spin contact interaction and orbit-orbit interaction,are calculated respectively.The results are in good agreement with experimental data.

  9. A general end point free energy calculation method based on microscopic configurational space coarse-graining

    CERN Document Server

    Tian, Pu

    2015-01-01

    Free energy is arguably the most important thermodynamic property for physical systems. Despite the fact that free energy is a state function, presently available rigorous methodologies, such as those based on thermodynamic integration (TI) or non-equilibrium work (NEW) analysis, involve energetic calculations on path(s) connecting the starting and the end macrostates. Meanwhile, presently widely utilized approximate end-point free energy methods lack rigorous treatment of conformational variation within end macrostates, and are consequently not sufficiently reliable. Here we present an alternative and rigorous end point free energy calculation formulation based on microscopic configurational space coarse graining, where the configurational space of a high dimensional system is divided into a large number of sufficiently fine and uniform elements, which were termed conformers. It was found that change of free energy is essentially decided by change of the number of conformers, with an error term that accounts...

  10. Ocean Thermal Energy Conversion (OTEC) platform configuration and integration. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Scott, R. J.

    1978-07-01

    Studies leading to the development of conceptual designs for two 400 MW Offshore Thermal Energy Conversion (OTEC) Commercial Plants are summarized. A detailed overview of the study Final Report which was completed in Jun 1978 is presented. The successful deployment of a Commercial OTEC Plant in the near term is dependent upon the optimization of the platform configuration and power plant output level. The optimization procedure is based on both technical and economic factors and is used to evaluate a relatively large number of alternatives; i.e., six hullforms, five plant outputs ranging from 50 to 500 megawatts (MW), and three deployment sites. The hullforms under consideration include the ship (barge), cylinder (disc), spar, submersible, semi-submersible, and sphere; while the deployment sites are Hawaii, New Orleans, and Key West. The second part of the Summary describes the development of the two platforms selected by DOE to be carried through the Conceptual Design level: a 400 MW ship and semi-submersible. These studies include platform and cold water pipe (CWP) optimization trade-offs, arrangements, structure, position control, seawater systems, and auxiliary systems. Deployment concepts are also discussed, followed by definition of costs and schedules for both alternatives. A development plan to bring both Commercial Plant alternatives to fruition via an intermediate 100 MW Demonstration Plant which will reduce technical risks to an acceptable level is presented.

  11. VLSI Architecture for Configurable and Low-Complexity Design of Hard-Decision Viterbi Decoding Algorithm

    Directory of Open Access Journals (Sweden)

    Rachmad Vidya Wicaksana Putra

    2016-06-01

    Full Text Available Convolutional encoding and data decoding are fundamental processes in convolutional error correction. One of the most popular error correction methods in decoding is the Viterbi algorithm. It is extensively implemented in many digital communication applications. Its VLSI design challenges are about area, speed, power, complexity and configurability. In this research, we specifically propose a VLSI architecture for a configurable and low-complexity design of a hard-decision Viterbi decoding algorithm. The configurable and low-complexity design is achieved by designing a generic VLSI architecture, optimizing each processing element (PE at the logical operation level and designing a conditional adapter. The proposed design can be configured for any predefined number of trace-backs, only by changing the trace-back parameter value. Its computational process only needs N + 2 clock cycles latency, with N is the number of trace-backs. Its configurability function has been proven for N = 8, N = 16, N = 32 and N = 64. Furthermore, the proposed design was synthesized and evaluated in Xilinx and Altera FPGA target boards for area consumption and speed performance.

  12. Preliminary verification of structure design for CN HCCB TBM with 1 × 4 configuration

    Energy Technology Data Exchange (ETDEWEB)

    Zhao, Zhou, E-mail: zhaozhou@swip.ac.cn; Zhou, Bing; Wang, Qijie; Cao, Qixiang; Feng, Kaiming; Wang, Xiaoyu; Zhang, Guoshu

    2016-02-15

    Highlights: • A new and simplification structural design scheme with 1 × 4 configuration is proposed for CN HCCB TBM. • The detail conceptual structural design for 1 × 4 TBM is completed. • The preliminary hydraulic analysis, thermo-hydraulic analysis and structural analysis for 1 × 4 TBM had been carried out. - Abstract: Based on the conceptual design of CN HCCB TBM with 1 × 4 configuration, the preliminary hydraulic analysis, thermo-hydraulic analysis and structural analysis had been carried out for it. Hydraulic and thermo-hydraulic analyses show that the coolant manifold system could meet the fluid design requirement preliminarily and the temperature of RAFMs structural parts, Be and Li{sub 4}SiO{sub 4} pebble beds are within the allowable range, and no zone shows a stress higher than the allowable limit in the preliminary structural analysis. These results indicate the design for CN HCCB TBM with 1 × 4 configuration is preliminary reasonable.

  13. A multi-perspective approach for the design of product configuration systems

    DEFF Research Database (Denmark)

    Hvam, Lars; Mortensen, Niels Henrik

    2007-01-01

    This article presents a procedure for building a product configuration system. The procedure includes, at the first phase, an analysis and redesign of the business processes, which are to be supported with product configuration systems. The next phase includes an analysis of the product assortmen......, and the set up of a so-called product variant master. Finally, the product configuration system is designed and implemented using object-oriented modeling. The procedure has been tested at a Danish company making electronic switchboards with positive results.......This article presents a procedure for building a product configuration system. The procedure includes, at the first phase, an analysis and redesign of the business processes, which are to be supported with product configuration systems. The next phase includes an analysis of the product assortment...

  14. Isomer Energy System Design Concepts

    Energy Technology Data Exchange (ETDEWEB)

    Vogt, D

    2003-09-01

    Isomer energy supplies offer the potential to increase the output power over time to accommodate varying power needs. Other materials with similar energy density (for example isotopic energy sources such as {sup 238}Pu) do not offer the potential to increase power with time. Often the design life of an energy source is significant when compared to the half-life of the isotope. As a result, the conventional isotopic energy supplies operate with significant excess power at start of life to meet the power needs at end-of-life. For example a {sup 238}Pu radioisotope energy supply with a 35-year design life must account for radioactive decay losses of about 25% of the plutonium present at the start of life. This decay loss is significant if the required output power from the device is constant with time. If the required power output from the device increases with time (such as some space applications), significant increases in power supply weight are required to meet design power requirements. Isomer energy supplies offer the potential to increase the output power over time to meet varying power needs, thereby offering a significant advantage over conventional systems. Isomer energy supplies also offer the possibility of being ''turned on'' based on need at a specific time. These characteristics offer distinct advantages to isomer energy supplies. This report examines the basic engineering characteristics of a hypothetical isomer energy supply in order to gain insight into properties of isomers that will make them potentially useful as energy sources in engineered systems. These isomer properties provide a basis for identification of candidate isomers and provide a basis for an isomer search.

  15. A comprehensive review of microbial electrolysis cells (MEC reactor designs and configurations for sustainable hydrogen gas production

    Directory of Open Access Journals (Sweden)

    Abudukeremu Kadier

    2016-03-01

    Full Text Available Hydrogen gas has tremendous potential as an environmentally acceptable energy carrier for vehicles. A cutting edge technology called a microbial electrolysis cell (MEC can achieve sustainable and clean hydrogen production from a wide range of renewable biomass and wastewaters. Enhancing the hydrogen production rate and lowering the energy input are the main challenges of MEC technology. MEC reactor design is one of the crucial factors which directly influence on hydrogen and current production rate in MECs. The rector design is also a key factor to up-scaling. Traditional MEC designs incorporated membranes, but it was recently shown that membrane-free designs can lead to both high hydrogen recoveries and production rates. Since then multiple studies have developed reactors that operate without membranes. This review provides a brief overview of recent advances in research on scalable MEC reactor design and configurations.

  16. Testing Circuit Models for the Energies of Coronal Magnetic Field Configurations

    CERN Document Server

    Wheatland, M S

    2003-01-01

    Circuit models involving bulk currents and inductances are often used to estimate the energies of coronal magnetic field configurations, in particular configurations associated with solar flares. The accuracy of circuit models is tested by comparing calculated energies of linear force-free fields with specified boundary conditions with corresponding circuit estimates. The circuit models are found to provide reasonable (order of magnitude) estimates for the energies of the non-potential components of the fields, and to reproduce observed functional dependences of the energies. However, substantial departure from the circuit estimates is observed for large values of the force-free parameter, and this is attributed to the influence of the non-potential component of the field on the path taken by the current.

  17. A multi-perspective approach for the design of product configuration systems

    DEFF Research Database (Denmark)

    Hvam, Lars; Mortensen, Niels Henrik

    2007-01-01

    This article presents a procedure for building a product configuration system. The procedure includes, at the first phase, an analysis and redesign of the business processes, which are to be supported with product configuration systems. The next phase includes an analysis of the product assortment......, and the set up of a so-called product variant master. Finally, the product configuration system is designed and implemented using object-oriented modeling. The procedure has been tested at a Danish company making electronic switchboards with positive results....

  18. Configraphics: Graph Theoretical Methods for Design and Analysis of Spatial Configurations

    Directory of Open Access Journals (Sweden)

    Pirouz Nourian

    2016-09-01

    Full Text Available This dissertation reports a PhD research on mathematical-computational models, methods, and techniques for analysis, synthesis, and evaluation of spatial configurations in architecture and urban design. Spatial configuration is a technical term that refers to the particular way in which a set of spaces are connected to one another as a network. Spatial configuration affects safety, security, and efficiency of functioning of complex buildings by facilitating certain patterns of movement and/or impeding other patterns. In cities and suburban built environments, spatial configuration affects accessibilities and influences travel behavioural patterns, e.g. choosing walking and cycling for short trips instead of travelling by cars. As such, spatial configuration effectively influences the social, economic, and environmental functioning of cities and complex buildings, by conducting human movement patterns.In this research, graph theory is used to mathematically model spatial configurations in order to provide intuitive ways of studying and designing spatial arrangements for architects and urban designers. The methods and tools presented in this dissertation are applicable in:arranging spatial layouts based on configuration graphs, e.g. by using bubble diagrams to ensure certain spatial requirements and qualities in complex buildings; andanalysing the potential effects of decisions on the likely spatial performance of buildings and on mobility patterns in built environments for systematic comparison of designs or plans, e.g. as to their aptitude for pedestrians and cyclists.The dissertation reports two parallel tracks of work on architectural and urban configurations. The core concept of the architectural configuration track is the ‘bubble diagram’ and the core concept of the urban configuration track is the ‘easiest paths’ for walking and cycling. Walking and cycling have been chosen as the foci of this theme as they involve active physical

  19. Design of a miniature electrolyte conductivity probe using ISFETs in a four point configuration

    NARCIS (Netherlands)

    Volanschi, A.; Olthuis, W.; Bergveld, P.

    1994-01-01

    In this work the design, fabrication and testing of a four point electrode configuration based on ISFETs for the measurement of electrolytic conductivity are presented. The final design uses a distance between the ISFET gates of only 100 ¿m allowing a chip area in contact with the electrolyte of 2.2

  20. Comparison of 2-D Magnetic Designs of Selected Coil Configurations for the Next European Dipole (NED)

    CERN Document Server

    Toral, F; Felice, H; Fessia, Paolo; Loveridge, P W; Regis, Federico; Rochford, J; Sanz, S; Schwerg, Nikolai; Védrine, P; Völlinger, Christine

    2007-01-01

    The Next European Dipole (NED) activity is developing a high-performance Nb3Sn wire (aiming at a non-copper critical current density of 1500 A/mm2 at 4.2 K and 15 T), within the framework of the Coordinated Accelerator Research in Europe (CARE) project. This activity is expected to lead to the fabrication of a large aperture, high field dipole magnet. In preparation for this phase, a Working Group on Magnet Design and Optimization (MDO) has been established to propose an optimal design. Other parallel Work Packages are concentrating on relevant topics, such as quench propagation simulation, innovative insulation techniques, and heat transfer measurements. In a first stage, the MDO Working Group has selected a number of coil configurations to be studied, together with salient parameters and features to be considered during the evaluation: the field quality, the superconductor efficiency, the conductor peak field, the stored magnetic energy, the Lorentz Forces and the fabrication difficulties. 2-D magnetic calc...

  1. Relativistic configuration interaction plus linearized-coupled-cluster calculations of U2 + energies, g factors, transition rates, and lifetimes

    Science.gov (United States)

    Savukov, I.; Safronova, U. I.; Safronova, M. S.

    2015-11-01

    Excitation energies, term designations, g factors, transition rates, and lifetimes of U2 + are determined using a relativistic configuration interaction (CI) + linearized-coupled-cluster (LCC) approach. The CI-LCC energies are compared with CI + many-body-perturbation-theory (MBPT) and available experimental energies. Close agreement has been found with experiment, within hundreds of cm-1. In addition, lifetimes of higher levels have been calculated for comparison with three experimentally measured lifetimes, and close agreement has been found within the experimental error. CI-LCC calculations constitute a benchmark test of the CI + all-order method in complex relativistic systems such as actinides and their ions with many valence electrons. The theory yields many energy levels, g factors, transition rates, and lifetimes of U2 + that are not available from experiment. The theory can be applied to other multivalence atoms and ions, which would be of interest to many applications.

  2. An optimal energy management development for various configuration of plug-in and hybrid electric vehicle

    Institute of Scientific and Technical Information of China (English)

    Morteza Montazeri-Gh; Mehdi Mahmoodi-K

    2015-01-01

    Due to soaring fuel prices and environmental concerns, hybrid electric vehicle (HEV) technology attracts more attentions in last decade. Energy management system, configuration of HEV and traffic conditions are the main factors which affect HEV's fuel consumption, emission and performance. Therefore, optimal management of the energy components is a key element for the success of a HEV. An optimal energy management system is developed for HEV based on genetic algorithm. Then, different powertrain system component combinations effects are investigated in various driving cycles. HEV simulation results are compared for default rule-based, fuzzy and GA-fuzzy controllers by using ADVISOR. The results indicate the effectiveness of proposed optimal controller over real world driving cycles. Also, an optimal powertrain configuration to improve fuel consumption and emission efficiency is proposed for each driving condition. Finally, the effects of batteries in initial state of charge and hybridization factor are investigated on HEV performance to evaluate fuel consumption and emissions. Fuel consumption average reduction of about 14% is obtained for optimal configuration data in contrast to default configuration. Also results indicate that proposed controller has reduced emission of about 10% in various traffic conditions.

  3. Disassemblability modeling technology of configurable product based on disassembly constraint relation weighted design structure matrix(DSM)

    Science.gov (United States)

    Qiu, Lemiao; Liu, Xiaojian; Zhang, Shuyou; Sun, Liangfeng

    2014-05-01

    The current research of configurable product disassemblability focuses on disassemblability evaluation and disassembly sequence planning. Little work has been done on quantitative analysis of configurable product disassemblability. The disassemblability modeling technology for configurable product based on disassembly constraint relation weighted design structure matrix (DSM) is proposed. Major factors affecting the disassemblability of configurable product are analyzed, and the disassembling degrees between components in configurable product are obtained by calculating disassembly entropies such as joint type, joint quantity, disassembly path, disassembly accessibility and material compatibility. The disassembly constraint relation weighted DSM of configurable product is constructed and configuration modules are formed by matrix decomposition and tearing operations. The disassembly constraint relation in configuration modules is strong coupling, and the disassembly constraint relation between modules is weak coupling, and the disassemblability configuration model is constructed based on configuration module. Finally, taking a hydraulic forging press as an example, the decomposed weak coupling components are used as configuration modules alone, components with a strong coupling are aggregated into configuration modules, and the disassembly sequence of components inside configuration modules is optimized by tearing operation. A disassemblability configuration model of the hydraulic forging press is constructed. By researching the disassemblability modeling technology of product configuration design based on disassembly constraint relation weighted DSM, the disassembly property in maintenance, recycling and reuse of configurable product are optimized.

  4. Applying CBR to machine tool product configuration design oriented to customer requirements

    Science.gov (United States)

    Wang, Pengjia; Gong, Yadong; Xie, Hualong; Liu, Yongxian; Nee, Andrew Yehching

    2017-01-01

    Product customization is a trend in the current market-oriented manufacturing environment. However, deduction from customer requirements to design results and evaluation of design alternatives are still heavily reliant on the designer's experience and knowledge. To solve the problem of fuzziness and uncertainty of customer requirements in product configuration, an analysis method based on the grey rough model is presented. The customer requirements can be converted into technical characteristics effectively. In addition, an optimization decision model for product planning is established to help the enterprises select the key technical characteristics under the constraints of cost and time to serve the customer to maximal satisfaction. A new case retrieval approach that combines the self-organizing map and fuzzy similarity priority ratio method is proposed in case-based design. The self-organizing map can reduce the retrieval range and increase the retrieval efficiency, and the fuzzy similarity priority ratio method can evaluate the similarity of cases comprehensively. To ensure that the final case has the best overall performance, an evaluation method of similar cases based on grey correlation analysis is proposed to evaluate similar cases to select the most suitable case. Furthermore, a computer-aided system is developed using MATLAB GUI to assist the product configuration design. The actual example and result on an ETC series machine tool product show that the proposed method is effective, rapid and accurate in the process of product configuration. The proposed methodology provides a detailed instruction for the product configuration design oriented to customer requirements.

  5. Applying CBR to machine tool product configuration design oriented to customer requirements

    Science.gov (United States)

    Wang, Pengjia; Gong, Yadong; Xie, Hualong; Liu, Yongxian; Nee, Andrew Yehching

    2016-03-01

    Product customization is a trend in the current market-oriented manufacturing environment. However, deduction from customer requirements to design results and evaluation of design alternatives are still heavily reliant on the designer's experience and knowledge. To solve the problem of fuzziness and uncertainty of customer requirements in product configuration, an analysis method based on the grey rough model is presented. The customer requirements can be converted into technical characteristics effectively. In addition, an optimization decision model for product planning is established to help the enterprises select the key technical characteristics under the constraints of cost and time to serve the customer to maximal satisfaction. A new case retrieval approach that combines the self-organizing map and fuzzy similarity priority ratio method is proposed in case-based design. The self-organizing map can reduce the retrieval range and increase the retrieval efficiency, and the fuzzy similarity priority ratio method can evaluate the similarity of cases comprehensively. To ensure that the final case has the best overall performance, an evaluation method of similar cases based on grey correlation analysis is proposed to evaluate similar cases to select the most suitable case. Furthermore, a computer-aided system is developed using MATLAB GUI to assist the product configuration design. The actual example and result on an ETC series machine tool product show that the proposed method is effective, rapid and accurate in the process of product configuration. The proposed methodology provides a detailed instruction for the product configuration design oriented to customer requirements.

  6. Optimal configuration of power generating systems in isolated island with renewable energy

    Energy Technology Data Exchange (ETDEWEB)

    Senjyu, Tomonobu; Hayashi, Daisuke; Yona, Atsushi; Urasaki, Naomitsu [Faculty of Engineering, University of the Ryukyus, 1 Senbaru, Nishihara-cho, Nakagami, Okinawa 903-0213 (Japan); Funabashi, Toshihisa [Meidensha Corporation, 36-2 Nihonbashi Hakozakicho, Chuo-ku, Tokyo 103-8515 (Japan)

    2007-09-15

    In isolated islands, usually diesel generators supply electric power. However, there are problems, e.g., a lack of fossil fuel, environmental pollution etc. So, isolated island, e.g. Miyako island, installs renewable energy power production plants. However, renewable energy power production plants are very costly. This paper presents an optimal configuration of power system in isolated island installing renewable energy power production plants. The generating system consists of diesel generators, wind turbine generators, PV system and batteries. Using the proposed method, operation cost can be reduced about 10% in comparison with diesel generators only from simulation results. (author)

  7. Concept of Accumulation System Configuration Enabling the Usage of Low-Potential Wind Energy

    Directory of Open Access Journals (Sweden)

    Kudelas, D.

    2006-01-01

    Full Text Available The construction concept will allow gaining the maximum value of aerodynamic effectiveness in a wide range of service conditions. In this way conceived wind aggregate will enable capturing the low-potential wind energy and its transformation and accumulation into electric energy usable as peak energy by the means of energetic converters with capacitance accumulation. Part of the solution is also a configuration concept of objective wind energetic unit with non-electric accumulation with trend to the possibility of a wide usage in the energetic network structures.

  8. Economic evaluation of flying-qualities design criteria for a transport configured with relaxed static stability

    Science.gov (United States)

    Sliwa, S. M.

    1980-01-01

    Direct constrained parameter optimization was used to optimally size a medium range transport for minimum direct operating cost. Several stability and control constraints were varied to study the sensitivity of the configuration to specifying the unaugmented flying qualities of transports designed to take maximum advantage of relaxed static stability augmentation systems. Additionally, a number of handling qualities related design constants were studied with respect to their impact on the design.

  9. Utilization of Minor Actinides as a Fuel Component for Ultra-Long Life Bhr Configurations: Designs, Advantages and Limitations

    Energy Technology Data Exchange (ETDEWEB)

    Dr. Pavel V. Tsvetkov

    2009-05-20

    This project assessed the advantages and limitations of using minor actinides as a fuel component to achieve ultra-long life Very High Temperature Reactor (VHTR) configurations. Researchers considered and compared the capabilities of pebble-bed and prismatic core designs with advanced actinide fuels to achieve ultra-long operation without refueling. Since both core designs permit flexibility in component configuration, fuel utilization, and fuel management, it is possible to improve fissile properties of minor actinides by neutron spectrum shifting through configuration adjustments. The project studied advanced actinide fuels, which could reduce the long-term radio-toxicity and heat load of high-level waste sent to a geologic repository and enable recovery of the energy contained in spent fuel. The ultra-long core life autonomous approach may reduce the technical need for additional repositories and is capable to improve marketability of the Generation IV VHTR by allowing worldwide deployment, including remote regions and regions with limited industrial resources. Utilization of minor actinides in nuclear reactors facilitates developments of new fuel cycles towards sustainable nuclear energy scenarios.

  10. A new sensor-based self-configurable bandstop filter for reducing the energy leakage in industrial microwave ovens

    Science.gov (United States)

    Clemente-Fernández, F. J.; Monzó-Cabrera, J.; Pedreño-Molina, J. L.; Lozano-Guerrero, A. J.; Fayos-Fernández, J.; Díaz-Morcillo, A.

    2012-06-01

    In this work a new sensor-based self-configurable waveguide bandstop filter that uses a combination of metallic irises and reconfigurable posts for reducing the energy leakage in industrial microwave ovens is presented and validated through a procedure fully based on measurements. Several optimization and reconfiguration alternatives of the moving posts such as genetic algorithms and parametric sweeps are assessed. Results show that good attenuation values can be obtained for all the analyzed scenarios. In particular, genetic algorithms are shown as the best search strategy. Design and optimization times are also reduced when using the proposed filter compared to computer simulations.

  11. Satellite Constellation Configuration Design with Rapid Performance Calculation and Ordinal Optimization

    Institute of Scientific and Technical Information of China (English)

    CUI Hongzheng; HAN Chao

    2011-01-01

    Satellite constellation configuration design is a complicated and time-consuming simulation optimization problem.In this paper,a new method called the rapid method for satellite constellation performance calculation is developed by the Hermite interpolation technique to reduce the computing complication and time.The constellation configuration optimization model is established on the basis of the rapid performance calculation.To reduce the search space and enhance the optimization efficiency,this paper presents a new constellation optimization strategy based on the ordinal optimization(00)theory and expands the algorithm realization for constellation optimization including precise and crude models,ordered performance curves,selection rules and selected subsets.Two experiments about navigation constellation and space based surveillance system(SBSS)are carried out and the analysis of simulation results indicates that the ordinal optimization for satellite constellation configuration design is effective.

  12. Analysis of optimal design configurations for a multiple disk centrifugal blood pump.

    Science.gov (United States)

    Miller, G E; Fink, R

    1999-06-01

    A multiple disk centrifugal pump was analyzed as a blood pump for use in cardiac assistance or as a bridge to transplant device. The original configuration consisted of 6 parallel disks with 0.016 inch spacing between disks. This pump suffered from a degradation of flow with increasing afterload. A study was conducted to analyze flow performance as a function of afterload, preload, and motor speed. Configurations were examined including 4, 5, and 6 disks each with spacings of 0.15, 0.20, and 0.25 inches. Flow rates were examined for variations in afterload from 60-130 mm Hg, in preload from 0-20 mm Hg and for motor speeds of 1,250, 1,500, and 1,750 rpm. Analyses of afterload effects were intended to determine those configurations that produced less flow degradation with increasing afterload. Analyses of motor speed effects were intended to determine any configurations that produced greater flow increases with increasing motor speed. A hemolysis study was also performed. Both plasma free hemoglobin and the index of hemolysis were compared to data reported for other centrifugal blood flow devices. Results indicated that a 5 disk configuration with a 0.15 inch spacing produced optimal flow results with minimal degradation at higher afterloads. No optimal configuration based upon motor speed was indicated. Preload effects on pump performance were minimal. Hemolysis results indicated minimal blood damage with levels below those of many other centrifugal blood pump designs.

  13. Relativistic configuration-interaction calculation of $K\\alpha$ transition energies in beryllium-like argon

    CERN Document Server

    Yerokhin, V A; Fritzsche, S

    2014-01-01

    Relativistic configuration-interaction calculations have been performed for the energy levels of the low-lying and core-excited states of beryllium-like argon, Ar$^{14+}$. These calculations include the one-loop QED effects as obtained by two different methods, the screening-potential approach as well as the model QED operator approach. The calculations are supplemented by a systematic estimation of uncertainties of theoretical predictions.

  14. 49 CFR 232.603 - Design, interoperability, and configuration management requirements.

    Science.gov (United States)

    2010-10-01

    ... (Continued) FEDERAL RAILROAD ADMINISTRATION, DEPARTMENT OF TRANSPORTATION BRAKE SYSTEM SAFETY STANDARDS FOR... Pneumatic (ECP) Braking Systems § 232.603 Design, interoperability, and configuration management requirements. (a) General. A freight car or freight train equipped with an ECP brake system shall, at a...

  15. Analysis of the characteristics of slot design affecting resistance to sliding during active archwire configurations

    OpenAIRE

    Nucera, Riccardo; Giudice, Antonino Lo; Matarese, Giovanni; Artemisia, Alessandro; Bramanti, Ennio; Crupi, Paolo; Cordasco, Giancarlo

    2013-01-01

    Background During orthodontic treatment, a low resistance to slide (RS) is desirable when sliding mechanics are used. Many studies showed that several variables affect the RS at the bracket-wire interface; among these, the design of the bracket slot has not been deeply investigated yet. This study aimed to clarify the effect of different slot designs on the RS expressed by five types of low-friction brackets in vertical and horizontal active configurations of the wire. Methods Five low-fricti...

  16. Wing Configuration Impact on Design Optimums for a Subsonic Passenger Transport

    Science.gov (United States)

    Wells, Douglas P.

    2014-01-01

    This study sought to compare four aircraft wing configurations at a conceptual level using a multi-disciplinary optimization (MDO) process. The MDO framework used was created by Georgia Institute of Technology and Virginia Polytechnic Institute and State University. They created a multi-disciplinary design and optimization environment that could capture the unique features of the truss-braced wing (TBW) configuration. The four wing configurations selected for the study were a low wing cantilever installation, a high wing cantilever, a strut-braced wing, and a single jury TBW. The mission that was used for this study was a 160 passenger transport aircraft with a design range of 2,875 nautical miles at the design payload, flown at a cruise Mach number of 0.78. This paper includes discussion and optimization results for multiple design objectives. Five design objectives were chosen to illustrate the impact of selected objective on the optimization result: minimum takeoff gross weight (TOGW), minimum operating empty weight, minimum block fuel weight, maximum start of cruise lift-to-drag ratio, and minimum start of cruise drag coefficient. The results show that the design objective selected will impact the characteristics of the optimized aircraft. Although minimum life cycle cost was not one of the objectives, TOGW is often used as a proxy for life cycle cost. The low wing cantilever had the lowest TOGW followed by the strut-braced wing.

  17. Design of 3-dimensional complex airplane configurations with specified pressure distribution via optimization

    Science.gov (United States)

    Kubrynski, Krzysztof

    1991-01-01

    A subcritical panel method applied to flow analysis and aerodynamic design of complex aircraft configurations is presented. The analysis method is based on linearized, compressible, subsonic flow equations and indirect Dirichlet boundary conditions. Quadratic dipol and linear source distribution on flat panels are applied. In the case of aerodynamic design, the geometry which minimizes differences between design and actual pressure distribution is found iteratively, using numerical optimization technique. Geometry modifications are modeled by surface transpiration concept. Constraints in respect to resulting geometry can be specified. A number of complex 3-dimensional design examples are presented. The software is adopted to personal computers, and as result an unexpected low cost of computations is obtained.

  18. The Modern Design of Experiments for Configuration Aerodynamics: A Case Study

    Science.gov (United States)

    DeLoach, Richard

    2006-01-01

    The effects of slowly varying and persisting covariate effects on the accuracy and precision of experimental result is reviewed, as is the rationale for run-order randomization as a quality assurance tactic employed in the Modern Design of Experiments (MDOE) to defend against such effects. Considerable analytical complexity is introduced by restrictions on randomization in configuration aerodynamics tests because they involve hard-to-change configuration variables that cannot be randomized conveniently. Tradeoffs are examined between quality and productivity associated with varying degrees of rigor in accounting for such randomization restrictions. Certain characteristics of a configuration aerodynamics test are considered that may justify a relaxed accounting for randomization restrictions to achieve a significant reduction in analytical complexity with a comparably negligible adverse impact on the validity of the experimental results.

  19. A multi perspective approach for the design of product configuration systems

    DEFF Research Database (Denmark)

    Hvam, Lars

    2004-01-01

    This article presents a procedure for building product configuration systems. The procedure includes, as the first phase, an analysis and redesign of the business processes, which are to be supported with product configuration systems. The next phase includes an analysis of the product assortment......, and the set up of a so-called product variant master. Finally the product configuration system is designed and implemented using object oriented modeling. The procedure has been tested in several companies. This article includes the experiences from the most recent project, which has been carried out at Demex...... Electric – a Danish company making electronic switchboards. The research has been carried out at the Centre for Product Modelling, Department of Manufacturing Engineering and Management at the Technical University of Denmark....

  20. A multi perspective approach for the design of product configuration systems

    DEFF Research Database (Denmark)

    Hvam, Lars

    2004-01-01

    , and the set up of a so-called product variant master. Finally the product configuration system is designed and implemented using object oriented modeling. The procedure has been tested in several companies. This article includes the experiences from the most recent project, which has been carried out at Demex......This article presents a procedure for building product configuration systems. The procedure includes, as the first phase, an analysis and redesign of the business processes, which are to be supported with product configuration systems. The next phase includes an analysis of the product assortment...... Electric – a Danish company making electronic switchboards. The research has been carried out at the Centre for Product Modelling, Department of Manufacturing Engineering and Management at the Technical University of Denmark....

  1. A configurable process for design of object-oriented software architectures

    DEFF Research Database (Denmark)

    lønvig, Birgitte

    combinations of problems and solutions in a number of different domains. The workflow of how to configure a process for a domain is although applicable for different domains. The software architecture design process is based on a general conceptual framework consisting of domain characteristics, requirements......When we design large complex software systems, such as systems in the telecommunications world, and we follow one of the standard object-oriented methods or processes, we end up with a system that fulfills the requirements of functionality. However, it is difficult to ensure that other requirements......, such as modifiability and reusability, are fulfilled. Furthermore the architecture is not explicitly described and is therefore difficult to comprehend. This Ph. D. dissertation defines a configurable process for design of object-oriented software architectures. The process can be regarded as an extension to standard...

  2. The Energy-Water Nexus: An Analysis and Comparison of Various Configurations Integrating Desalination with Renewable Power

    Directory of Open Access Journals (Sweden)

    Gary M. Gold

    2015-04-01

    Full Text Available This investigation studies desalination powered by wind and solar energy, including a study of a configuration using PVT solar panels. First, a water treatment was developed to estimate the power requirement for brackish groundwater reverse-osmosis (BWRO desalination. Next, an energy model was designed to (1 size a wind farm based on this power requirement and (2 size a solar farm to preheat water before reverse osmosis treatment. Finally, an integrated model was developed that combines results from the water treatment and energy models. The integrated model optimizes performances of the proposed facility to maximize daily operational profits. Results indicate that integrated facility can reduce grid-purchased electricity costs by 88% during summer months and 89% during winter when compared to a stand-alone desalination plant. Additionally, the model suggests that the integrated configuration can generate $574 during summer and $252 during winter from sales of wind- and solar-generated electricity to supplement revenue from water production. These results indicate that an integrated facility combining desalination, wind power, and solar power can potentially reduce reliance on grid-purchased electricity and advance the use of renewable power.

  3. Self-gravitating field configurations: The role of the energy-momentum trace

    CERN Document Server

    Hod, Shahar

    2014-01-01

    Static spherically-symmetric matter distributions whose energy-momentum tensor is characterized by a non-negative trace are studied analytically within the framework of general relativity. We prove that such field configurations are necessarily highly relativistic objects. In particular, for matter fields with $T\\geq\\alpha\\cdot\\rho\\geq0$ (here $T$ and $\\rho$ are respectively the trace of the energy-momentum tensor and the energy density of the fields, and $\\alpha$ is a non-negative constant), we obtain the lower bound $\\text{max}_r\\{2m(r)/r\\}>(2+2\\alpha)/(3+2\\alpha)$ on the compactness (mass-to-radius ratio) of regular field configurations. In addition, we prove that these compact objects necessarily possess (at least) {\\it two} photon-spheres, one of which exhibits {\\it stable} trapping of null geodesics. The presence of stable photon-spheres in the corresponding curved spacetimes indicates that these compact objects may be nonlinearly unstable. We therefore conjecture that a negative trace of the energy-mom...

  4. A generalized free energy perturbation theory accounting for end states with differing configuration space volume.

    Science.gov (United States)

    Ullmann, R Thomas; Ullmann, G Matthias

    2011-01-27

    We present a generalized free energy perturbation theory that is inspired by Monte Carlo techniques and based on a microstate description of a transformation between two states of a physical system. It is shown that the present free energy perturbation theory stated by the Zwanzig equation follows as a special case of our theory. Our method uses a stochastic mapping of the end states that associates a given microstate from one ensemble with a microstate from the adjacent ensemble according to a probability distribution. In contrast, previous free energy perturbation methods use a static, deterministic mapping that associates fixed pairs of microstates from the two ensembles. The advantages of our approach are that end states of differing configuration space volume can be treated easily also in the case of discrete configuration spaces and that the method does not require the potentially cumbersome search for an optimal deterministic mapping. The application of our theory is illustrated by some example problems. We discuss practical applications for which our findings could be relevant and point out perspectives for further development of the free energy perturbation theory.

  5. Utilization of design principles for hybrid learning configurations by interprofessional design teams

    NARCIS (Netherlands)

    Cremers, Petra H.M.; Wals, Arjen E.J.; Wesselink, Renate; Mulder, Martin

    2017-01-01

    Educational design research yields design knowledge, often in the form of design principles or guidelines that provide the rationale or ‘know-why’ for the design of educational interventions. As such, design principles can be utilized by designers in contexts other than the research context in which

  6. Utilization of Design Principles for Hybrid Learning Configurations by Interprofessional Design Teams

    Science.gov (United States)

    Cremers, Petra H. M.; Wals, Arjen E. J.; Wesselink, Renate; Mulder, Martin

    2017-01-01

    Educational design research yields design knowledge, often in the form of design principles or guidelines that provide the rationale or "know-why" for the design of educational interventions. As such, design principles can be utilized by designers in contexts other than the research context in which they were generated. Although research…

  7. Basic configuration of the mean energy line (LME) V2.0; Configuration de base de la ligne moyenne energie (LME) V2.0

    Energy Technology Data Exchange (ETDEWEB)

    Uriot, D. [CEA Saclay, 91 - Gif sur Yvette (France); Bertrand, P. [Grand Accelerateur National d' Ions Lourds (GANIL), 14 - Caen (France); Biarrotte, J.L. [Paris-11 Univ., 91 - Orsay (France). Inst. de Physique Nucleaire

    2007-06-15

    The main purpose of the mean energy line (LME) is to receive the beam accelerated by the RFQ (deuterons, ions with q/A = 1/3, protons) and dispatch it to the linac in optimized conditions. LME is about 8 m long and the vacuum required is 10{sup -6} Pa and is composed of 10 identical quadrupoles. This document describes the state of the design of the LME for the injection system of the linac within the SPIRAL-2 project.

  8. Reliability-based design optimization for nonlinear energy harvesters

    Science.gov (United States)

    Seong, Sumin; Lee, Soobum; Hu, Chao

    2015-03-01

    The power output of a vibration energy harvesting device is highly sensitive to uncertainties in materials, manufacturing, and operating conditions. Although the use of a nonlinear spring (e.g., snap-through mechanism) in energy harvesting device has been reported to reduce the sensitivity of power output with respect to the excitation frequency, the nonlinear spring characteristic remains significantly sensitive and it causes unreliable power generation. In this paper, we present a reliability-based design optimization (RBDO) study of vibration energy harvesters. For a nonlinear harvester, a purely mechanical nonlinear spring design implemented in the middle of cantilever beam harvester is considered in the study. This design has the curved section in the center of beam that causes bi-stable configuration. When vibrating, the inertia of the tip mass activates the curved shell to cause snap-through buckling and make the nature of vibration nonlinear. In this paper, deterministic optimization (DO) is performed to obtain deterministic optimum of linear and nonlinear energy harvester configuration. As a result of the deterministic optimization, an optimum bi-stable vibration configuration of nonlinear harvester can be obtained for reliable power generation despite uncertainty on input vibration condition. For the linear harvester, RBDO is additionally performed to find the optimum design that satisfies a target reliability on power generation, while accounting for uncertainty in material properties and geometric parameters.

  9. Submersible Unmanned Aerial Vehicle: Configuration Design and Analysis Based on Computational Fluid Dynamics

    Directory of Open Access Journals (Sweden)

    Wang Qinyang

    2017-01-01

    Full Text Available Submersible aerial vehicle is capable of both flying in the air and submerging in the water. Advanced Research Project Agency (DARPA outlined a challenging set of requirements for a submersible aircraft and solicited innovative research proposals on submersible aircraft since 2008. In this paper, a conceptual configuration design scheme of submersible unmanned aerial vehicle is proposed. This submersible UAV lands on the surface of water, then adjusts its own density to entry water. On the contrary, it emerges from water by adjusting its own density and then takes off from the surface of water. Wing of the UAV is whirling wing. It is set along aircraft’s fuselage while submerging for lift reduction. We analysis aerodynamic and hydrodynamic performance of this UAV by CFD method, especially compare the hydrodynamic performance of the whirling wing configuration and normal configuration. It turns out that whirling wing is beneficial for submerging. This result proves that the configuration design scheme proposed in this paper is feasible and suitable for a submersible unmanned aerial vehicle.

  10. Research on the configuration design method of heterogeneous constellation reconstruction under the multiple objective and multiple constraint

    Science.gov (United States)

    Zhao, Shuang; Xu, Yanli; Dai, Huayu

    2017-05-01

    Aiming at the problem of configuration design of heterogeneous constellation reconstruction, a design method of heterogeneous constellation reconstruction based on multi objective and multi constraints is proposed. At first, the concept of heterogeneous constellation is defined. Secondly, the heterogeneous constellation reconstruction methods were analyzed, and then the two typical existing design methods of reconstruction, phase position uniformity method and reconstruction configuration design method based on optimization algorithm are summarized. The advantages and shortcomings of different reconstruction configuration design methods are compared, finally the heterogeneous constellation reconstruction configuration design is currently facing problems are analyzed and put forward the thinking about the reconstruction index system of heterogeneous constellation and the selection of optimal variables and the establishment of constraints in the optimization design of the configuration.

  11. Ergodicity, configurational entropy and free energy in pigment solutions and plant photosystems: influence of excited state lifetime.

    Science.gov (United States)

    Jennings, Robert C; Zucchelli, Giuseppe

    2014-01-01

    We examine ergodicity and configurational entropy for a dilute pigment solution and for a suspension of plant photosystem particles in which both ground and excited state pigments are present. It is concluded that the pigment solution, due to the extreme brevity of the excited state lifetime, is non-ergodic and the configurational entropy approaches zero. Conversely, due to the rapid energy transfer among pigments, each photosystem is ergodic and the configurational entropy is positive. This decreases the free energy of the single photosystem pigment array by a small amount. On the other hand, the suspension of photosystems is non-ergodic and the configurational entropy approaches zero. The overall configurational entropy which, in principle, includes contributions from both the single excited photosystems and the suspension which contains excited photosystems, also approaches zero. Thus the configurational entropy upon photon absorption by either a pigment solution or a suspension of photosystem particles is approximately zero.

  12. ATM Technology Demonstration-1 Phase II Boeing Configurable Graphical Display (CGD) Software Design Description

    Science.gov (United States)

    Wilber, George F.

    2017-01-01

    This Software Description Document (SDD) captures the design for developing the Flight Interval Management (FIM) system Configurable Graphics Display (CGD) software. Specifically this SDD describes aspects of the Boeing CGD software and the surrounding context and interfaces. It does not describe the Honeywell components of the CGD system. The SDD provides the system overview, architectural design, and detailed design with all the necessary information to implement the Boeing components of the CGD software and integrate them into the CGD subsystem within the larger FIM system. Overall system and CGD system-level requirements are derived from the CGD SRS (in turn derived from the Boeing System Requirements Design Document (SRDD)). Display and look-and-feel requirements are derived from Human Machine Interface (HMI) design documents and working group recommendations. This Boeing CGD SDD is required to support the upcoming Critical Design Review (CDR).

  13. Analysis of electric energy consumption of automatic milking systems in different configurations and operative conditions.

    Science.gov (United States)

    Calcante, Aldo; Tangorra, Francesco M; Oberti, Roberto

    2016-05-01

    Automatic milking systems (AMS) have been a revolutionary innovation in dairy cow farming. Currently, more than 10,000 dairy cow farms worldwide use AMS to milk their cows. Electric consumption is one of the most relevant and uncontrollable operational cost of AMS, ranging between 35 and 40% of their total annual operational costs. The aim of the present study was to measure and analyze the electric energy consumption of 4 AMS with different configurations: single box, central unit featuring a central vacuum system for 1 cow unit and for 2 cow units. The electrical consumption (daily consumption, daily consumption per cow milked, consumption per milking, and consumption per 100L of milk) of each AMS (milking unit + air compressor) was measured using 2 energy analyzers. The measurement period lasted 24h with a sampling frequency of 0.2Hz. The daily total energy consumption (milking unit + air compressor) ranged between 45.4 and 81.3 kWh; the consumption per cow milked ranged between 0.59 and 0.99 kWh; the consumption per milking ranged between 0.21 and 0.33 kWh; and the consumption per 100L of milk ranged between 1.80 to 2.44 kWh according to the different configurations and operational contexts considered. Results showed that AMS electric consumption was mainly conditioned by farm management rather than machine characteristics/architectures. Copyright © 2016 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

  14. A multi-perspective approach for the design of Product Configuration Systems - an evaluation of industry applications

    DEFF Research Database (Denmark)

    Hvam, Lars

    2004-01-01

    This article presents a suggested procedure for modelling and implementation of product configuration systems. The procedure has been applied in several industrial companies. The procedure comprises: • Analysis of the business processes to be supported by a product configuration system. Furthermore......, a de-marcation and definition of the configuration system to be designed. • Analysis and modelling of the part of the company’s product assortment which is to be included in the con-figuration system. • Selection of configuration software and programming of the configuration system. • Implementation...... of the configuration system. • Operations, maintenance and further development of the configuration system. The procedure has been developed on the basis of the general methods for modelling IT-systems (UML) as well as on the theory for modelling technical systems and theory for the development of business processes...

  15. Monte Carlo configuration interaction applied to multipole moments, ionisation energies and electron affinities

    CERN Document Server

    Coe, J P; Paterson, M J

    2013-01-01

    The method of Monte Carlo configuration interaction (MCCI) [1,2] is applied to the calculation of multipole moments. We look at the ground and excited state dipole moments in carbon monoxide. We then consider the dipole of NO, the quadrupole of the nitrogen molecule and of BH. An octupole of methane is also calculated. We consider experimental geometries and also stretched bonds. We show that these non-variational quantities may be found to relatively good accuracy when compared with FCI results, yet using only a small fraction of the full configuration interaction space. MCCI results in the aug-cc-pVDZ basis are seen to generally have reasonably good agreement with experiment. We also investigate the performance of MCCI when applied to ionisation energies and electron affinities of atoms in an aug-cc-pVQZ basis. We compare the MCCI results with full configuration-interaction quantum Monte Carlo [3,4] and `exact' non-relativistic results [3,4]. We show that MCCI could be a useful alternative for the calculati...

  16. Applications of a direct/iterative design method to complex transonic configurations

    Science.gov (United States)

    Smith, Leigh Ann; Campbell, Richard L.

    1992-01-01

    The current study explores the use of an automated direct/iterative design method for the reduction of drag in transport configurations, including configurations with engine nacelles. The method requires the user to choose a proper target-pressure distribution and then develops a corresponding airfoil section. The method can be applied to two-dimensional airfoil sections or to three-dimensional wings. The three cases that are presented show successful application of the method for reducing drag from various sources. The first two cases demonstrate the use of the method to reduce induced drag by designing to an elliptic span-load distribution and to reduce wave drag by decreasing the shock strength for a given lift. In the second case, a body-mounted nacelle is added and the method is successfully used to eliminate increases in wing drag associated with the nacelle addition by designing to an arbitrary pressure distribution as a result of the redesigning of a wing in combination with a given underwing nacelle to clean-wing, target-pressure distributions. These cases illustrate several possible uses of the method for reducing different types of drag. The magnitude of the obtainable drag reduction varies with the constraints of the problem and the configuration to be modified.

  17. Microelectronic circuit design for energy harvesting systems

    CERN Document Server

    Di Paolo Emilio, Maurizio

    2017-01-01

    This book describes the design of microelectronic circuits for energy harvesting, broadband energy conversion, new methods and technologies for energy conversion. The author also discusses the design of power management circuits and the implementation of voltage regulators. Coverage includes advanced methods in low and high power electronics, as well as principles of micro-scale design based on piezoelectric, electromagnetic and thermoelectric technologies with control and conditioning circuit design. Provides a single-source reference to energy harvesting and its applications; Serves as a practical guide to microelectronics design for energy harvesting, with application to mobile power supplies; Enables readers to develop energy harvesting systems for wearable/mobile electronics.

  18. Formulation of thermodynamics for the glassy state : Configurational energy as a modest source of energy

    NARCIS (Netherlands)

    Nieuwenhuizen, T.M.

    2001-01-01

    Glass is an under-cooled liquid that very slowly relaxes towards the equilibrium crystalline state. Its energy balance is ill understood, since it is widely believed that the glassy state cannot be described thermodynamically. However, the classical paradoxes involving the Ehrenfest relations and Pr

  19. Biomechanical and performance implications of weapon design: comparison of bullpup and conventional configurations.

    Science.gov (United States)

    Stone, Richard T; Moeller, Brandon F; Mayer, Robert R; Rosenquist, Bryce; Van Ryswyk, Darin; Eichorn, Drew

    2014-06-01

    Shooter accuracy and stability were monitored while firing two bullpup and two conventional configuration rifles of the same caliber in order to determine if one style of weapon results in superior performance. Considerable debate exists among police and military professionals regarding the differences between conventional configuration weapons, where the magazine and action are located ahead of the trigger, and bullpup configuration, where they are located behind the trigger (closer to the user). To date, no published research has attempted to evaluate this question from a physical ergonomics standpoint, and the knowledge that one style might improve stability or result in superior performance is of interest to countless military, law enforcement, and industry experts. A live-fire evaluation of both weapon styles was performed using a total of 48 participants. Shooting accuracy and fluctuations in biomechanical stability (center of pressure) were monitored while subjects used the weapons to perform standard drills. The bullpup weapon designs were found to provide a significant advantage in accuracy and shooter stability, while subjects showed considerable preference toward the conventional weapons. Although many mechanical and maintenance issues must be considered before committing to a bullpup or conventional weapon system, it is clear in terms of basic human stability that the bullpup is the more advantageous configuration. Results can be used by competitive shooter, military, law enforcement, and industry experts while outfitting personnel with a weapon system that leads to superior performance.

  20. The Analysis and Design of Low Boom Configurations Using CFD and Numerical Optimization Techniques

    Science.gov (United States)

    Siclari, Michael J.

    1999-01-01

    The use of computational fluid dynamics (CFD) for the analysis of sonic booms generated by aircraft has been shown to increase the accuracy and reliability of predictions. CFD takes into account important three-dimensional and nonlinear effects that are generally neglected by modified linear theory (MLT) methods. Up to the present time, CFD methods have been primarily used for analysis or prediction. Some investigators have used CFD to impact the design of low boom configurations using trial and error methods. One investigator developed a hybrid design method using a combination of Modified Linear Theory (e.g. F-functions) and CFD to provide equivalent area due to lift driven by a numerical optimizer to redesign or modify an existing configuration to achieve a shaped sonic boom signature. A three-dimensional design methodology has not yet been developed that completely uses nonlinear methods or CFD. Constrained numerical optimization techniques have existed for some time. Many of these methods use gradients to search for the minimum of a specified objective function subject to a variety of design variable bounds, linear and nonlinear constraints. Gradient based design optimization methods require the determination of the objective function gradients with respect to each of the design variables. These optimization methods are efficient and work well if the gradients can be obtained analytically. If analytical gradients are not available, the objective gradients or derivatives with respect to the design variables must be obtained numerically. To obtain numerical gradients, say, for 10 design variables, might require anywhere from 10 to 20 objective function evaluations. Typically, 5-10 global iterations of the optimizer are required to minimize the objective function. In terms of using CFD as a design optimization tool, the numerical evaluation of gradients can require anywhere from 100 to 200 CFD computations per design for only 10 design variables. If one CFD

  1. 10 CFR 434.508 - Determination of the design energy consumption and design energy cost.

    Science.gov (United States)

    2010-01-01

    ... 10 Energy 3 2010-01-01 2010-01-01 false Determination of the design energy consumption and design... FEDERAL COMMERCIAL AND MULTI-FAMILY HIGH RISE RESIDENTIAL BUILDINGS Building Energy Cost Compliance Alternative § 434.508 Determination of the design energy consumption and design energy cost. 508.1The...

  2. Configuration mixing within the energy density functional formalism: pathologies and cures

    CERN Document Server

    Lacroix, Denis; Duguet, Thomas

    2008-01-01

    Configuration mixing calculations performed in terms of the Skyrme/Gogny Energy Density Functional (EDF) rely on extending the Single-Reference energy functional into non-diagonal EDF kernels. The standard way to do so, based on an analogy with the pure Hamiltonian case and the use of the generalized Wick theorem, is responsible for the recently observed divergences and steps in Multi-Reference calculations. We summarize here the minimal solution to this problem recently proposed [Lacroix et al, arXiv:0809.2041] and applied with success to particle number restoration[Bender et al, arXiv:0809.2045]. Such a regularization method provides suitable corrections of pathologies for EDF depending on integer powers of the density. The specific case of fractional powers of the density[Duguet et al, arXiv:0809.2049] is also discussed.

  3. Multi-Objective Configuration Optimization of a Hybrid Energy Storage System

    Directory of Open Access Journals (Sweden)

    Shan Cheng

    2017-02-01

    Full Text Available This study aims to investigate multi-objective configuration optimization of a hybrid energy storage system (HESS. In order to maximize the stability of the wind power output with minimized HESS investment, a multi-objective model for optimal HESS configuration has been established, which proposes decreasing the installation and operation & maintenance costs of an HESS and improving the compensation satisfaction rate of wind power fluctuation. Besides, fuzzy control has been used to allocate power in the HESS for lengthening battery lifetime and ensuring HESS with enough energy to compensate the fluctuation of the next time interval. Instead of converting multiple objectives into one, a multi-objective particle swarm optimization with integration of bacteria quorum sensing and circular elimination (BC-MOPSO has been applied to provide diverse alternative solutions. In order to illustrate the feasibility and effectiveness of the proposed model and the application of BC-MOPSO, simulations along with analysis and discussion are carried out. The results verified the feasibility and effectiveness of the proposed approach.

  4. SimArray: a user-friendly and user-configurable microarray design tool

    Directory of Open Access Journals (Sweden)

    Meadows Lisa A

    2006-03-01

    Full Text Available Abstract Background Microarrays were first developed to assess gene expression but are now also used to map protein-binding sites and to assess allelic variation between individuals. Regardless of the intended application, efficient production and appropriate array design are key determinants of experimental success. Inefficient production can make larger-scale studies prohibitively expensive, whereas poor array design makes normalisation and data analysis problematic. Results We have developed a user-friendly tool, SimArray, which generates a randomised spot layout, computes a maximum meta-grid area, and estimates the print time, in response to user-specified design decisions. Selected parameters include: the number of probes to be printed; the microtitre plate format; the printing pin configuration, and the achievable spot density. SimArray is compatible with all current robotic spotters that employ 96-, 384- or 1536-well microtitre plates, and can be configured to reflect most production environments. Print time and maximum meta-grid area estimates facilitate evaluation of each array design for its suitability. Randomisation of the spot layout facilitates correction of systematic biases by normalisation. Conclusion SimArray is intended to help both established researchers and those new to the microarray field to develop microarray designs with randomised spot layouts that are compatible with their specific production environment. SimArray is an open-source program and is available from http://www.flychip.org.uk/SimArray/.

  5. Quasi-monopolar stimulation: a novel electrode design configuration for performance optimization of a retinal neuroprosthesis.

    Directory of Open Access Journals (Sweden)

    Gita Khalili Moghadam

    Full Text Available In retinal neuroprostheses, spatial interaction between electric fields from various electrodes - electric crosstalk - may occur in multielectrode arrays during simultaneous stimulation of the retina. Depending on the electrode design and placement, this crosstalk can either enhance or degrade the functional characteristics of a visual prosthesis. To optimize the device performance, a balance must be satisfied between the constructive interference of crosstalk on dynamic range and power consumption and its negative effect on artificial visual acuity. In the present computational modeling study, we have examined the trade-off in these positive and negative effects using a range of currently available electrode array configurations, compared to a recently proposed stimulation strategy - the quasi monopolar (QMP configuration - in which the return current is shared between local bipolar guards and a distant monopolar electrode. We evaluate the performance of the QMP configuration with respect to the implantation site and electrode geometry parameters. Our simulation results demonstrate that the beneficial effects of QMP are only significant at electrode-to-cell distances greater than the electrode dimensions. Possessing a relatively lower activation threshold, QMP was found to be superior to the bipolar configuration in terms of providing a relatively higher visual acuity. However, the threshold for QMP was more sensitive to the topological location of the electrode in the array, which may need to be considered when programming the manner in which electrode are simultaneously activated. This drawback can be offset with a wider dynamic range and lower power consumption of QMP. Furthermore, the ratio of monopolar return current to total return can be used to adjust the functional performance of QMP for a given implantation site and electrode parameters. We conclude that the QMP configuration can be used to improve visual information

  6. Designing for social configurations: pattern languages to inform the design of ubiquitous computing

    NARCIS (Netherlands)

    Denef, S.; Opperman, R.; Keyson, D.V.

    2011-01-01

    In this paper we present our approach for informing the design of ubiquitous computing by using pattern languages of human practice. By linking ethnography and design, this approach makes it possible to tackle the social dimension of ubiquitous computing in the design processes. Adding to the existi

  7. Probabilistic Design of Wave Energy Devices

    DEFF Research Database (Denmark)

    Sørensen, John Dalsgaard; Kofoed, Jens Peter; Ferreira, C.B.

    2011-01-01

    Wave energy has a large potential for contributing significantly to production of renewable energy. However, the wave energy sector is still not able to deliver cost competitive and reliable solutions. But the sector has already demonstrated several proofs of concepts. The design of wave energy...... and advocate for a probabilistic design approach, as it is assumed (in other areas this has been demonstrated) that this leads to more economical designs compared to designs based on deterministic methods. In the present paper a general framework for probabilistic design and reliability analysis of wave energy...

  8. Proof of Concept Study of Trade Space Configuration Tool for Spacecraft Design

    Science.gov (United States)

    Glidden, Geoffrey L.

    2009-01-01

    Spacecraft design is a very difficult and time consuming process because requirements and criteria are often changed or modified as the design is refined. Accounting for these adjustments in the design constraints plays a significant role in furthering the overall progress. There are numerous aspects and variables that hold significant influence on various characteristics of the design. This can be especially frustrating when attempting to conduct rapid trade space analysis on system configurations. Currently, the data and designs considered for trade space evaluations can only be displayed by using the traditional interfaces of Excel spreadsheets or CAD (Computer Aided Design) models. While helpful, these methods of analyzing the data from a systems engineering approach can be rather complicated and overwhelming. As a result, a proof of concept was conducted on a dynamic data visualization software called Thinkmap SDK (Software Developer Kit) to allow for better organization and understanding of the relationships between the various aspects that make up an entire design. The Orion Crew Module Aft Bay Subsystem was used as the test case for this study because the design and layout of many of the subsystem components will be significant in ensuring the overall center of gravity of the capsule is correct. A simplified model of this subsystem was created and programmed using Thinkmap SDK to create a preliminary prototype application of a Trade Space Configuration Tool. The completed application ensures that the core requirements for the Tool can be met. Further development is strongly suggested to produce a full prototype application to allow final evaluations and recommendations of the software capabilities.

  9. High-Speed Research: 1994 Sonic Boom Workshop. Configuration, Design, Analysis and Testing

    Science.gov (United States)

    McCurdy, David A. (Editor)

    1999-01-01

    The third High-Speed Research Sonic Boom Workshop was held at NASA Langley Research Center on June 1-3, 1994. The purpose of this workshop was to provide a forum for Government, industry, and university participants to present and discuss progress in their research. The workshop was organized into sessions dealing with atmospheric propagation; acceptability studies; and configuration design, and testing. Attendance at the workshop was by invitation only. The workshop proceedings include papers on design, analysis, and testing of low-boom high-speed civil transport configurations and experimental techniques for measuring sonic booms. Significant progress is noted in these areas in the time since the previous workshop a year earlier. The papers include preliminary results of sonic boom wind tunnel tests conducted during 1993 and 1994 on several low-boom designs. Results of a mission performance analysis of all low-boom designs are also included. Two experimental methods for measuring near-field signatures of airplanes in flight are reported.

  10. Study of advanced composite structural design concepts for an arrow wing supersonic cruise configuration, task 3

    Science.gov (United States)

    1978-01-01

    A structural design study was conducted to assess the relative merits of structural concepts using advanced composite materials for an advanced supersonic aircraft cruising at Mach 2.7. The configuration and structural arrangement developed during Task I and II of the study, was used as the baseline configuration. Allowable stresses and strains were established for boron and advanced graphite fibers based on projected fiber properties available in the next decade. Structural concepts were designed and analyzed using graphite polyimide and boron polyimide, applied to stiffened panels and conventional sandwich panels. The conventional sandwich panels were selected as the structural concept to be used on the wing structure. The upper and lower surface panels of the Task I arrow wing were redesigned using high-strength graphite polyimide sandwich panels over the titanium spars and ribs. The ATLAS computer system was used as the basis for stress analysis and resizing the surface panels using the loads from the Task II study, without adjustment for change in aeroelastic deformation. The flutter analysis indicated a decrease in the flutter speed compared to the baseline titanium wing design. The flutter analysis indicated a decrease in the flutter speed compared to the baseline titanium wing design. The flutter speed was increased to that of the titanium wing, with a weight penalty less than that of the metallic airplane.

  11. High-order moments of spin-orbit energy in a multielectron configuration

    Science.gov (United States)

    Na, Xieyu; Poirier, M.

    2016-07-01

    In order to analyze the energy-level distribution in complex ions such as those found in warm dense plasmas, this paper provides values for high-order moments of the spin-orbit energy in a multielectron configuration. Using second-quantization results and standard angular algebra or fully analytical expressions, explicit values are given for moments up to 10th order for the spin-orbit energy. Two analytical methods are proposed, using the uncoupled or coupled orbital and spin angular momenta. The case of multiple open subshells is considered with the help of cumulants. The proposed expressions for spin-orbit energy moments are compared to numerical computations from Cowan's code and agree with them. The convergence of the Gram-Charlier expansion involving these spin-orbit moments is analyzed. While a spectrum with infinitely thin components cannot be adequately represented by such an expansion, a suitable convolution procedure ensures the convergence of the Gram-Charlier series provided high-order terms are accounted for. A corrected analytical formula for the third-order moment involving both spin-orbit and electron-electron interactions turns out to be in fair agreement with Cowan's numerical computations.

  12. Designing for usability of 3D configuration in E-commerce : Interactive design of 3D in web applications

    OpenAIRE

    Axelsson, Alfred

    2017-01-01

    Mass production of consumer products is both wasteful and limit the consumers' power to influence the design of what they are buying. When shopping for a product, the customer must choose between a range of specific products with limited variations. What if the customer could make all the design choices, creating and buying the product according to his or her own needs? A 3D product generator holding a configurable model of a product was created to replace static content in online stores and ...

  13. On-line Configuration of Network Emulator for Intelligent Energy System Testbed Applications

    DEFF Research Database (Denmark)

    Kemal, Mohammed Seifu; Iov, Florin; Olsen, Rasmus Løvenstein

    2015-01-01

    Intelligent energy networks (or Smart Grids) provide efficient solutions for a grid integrated with near-real-time communication technologies between various grid assets in power generation, transmission and distribution systems. The design of a communication network associated with intelligent......-operable and resilient Smart Grid networks and how the current state of the art communication technologies are employed for smart control of energy distribution grids....

  14. The space shuttle ascent vehicle aerodynamic challenges configuration design and data base development

    Science.gov (United States)

    Dill, C. C.; Young, J. C.; Roberts, B. B.; Craig, M. K.; Hamilton, J. T.; Boyle, W. W.

    1985-01-01

    The phase B Space Shuttle systems definition studies resulted in a generic configuration consisting of a delta wing orbiter, and two solid rocket boosters (SRB) attached to an external fuel tank (ET). The initial challenge facing the aerodynamic community was aerodynamically optimizing, within limits, this configuration. As the Shuttle program developed and the sensitivities of the vehicle to aerodynamics were better understood the requirements of the aerodynamic data base grew. Adequately characterizing the vehicle to support the various design studies exploded the size of the data base to proportions that created a data modeling/management challenge for the aerodynamicist. The ascent aerodynamic data base originated primarily from wind tunnel test results. The complexity of the configuration rendered conventional analytic methods of little use. Initial wind tunnel tests provided results which included undesirable effects from model support tructure, inadequate element proximity, and inadequate plume simulation. The challenge to improve the quality of test results by determining the extent of these undesirable effects and subsequently develop testing techniques to eliminate them was imposed on the aerodynamic community. The challenges to the ascent aerodynamics community documented are unique due to the aerodynamic complexity of the Shuttle launch. Never before was such a complex vehicle aerodynamically characterized. The challenges were met with innovative engineering analyses/methodology development and wind tunnel testing techniques.

  15. Global Machine Design and Double X-point Equilibrium Configurations for Ignitor*

    Science.gov (United States)

    Bianchi, A.; Parodi, B.; Coppi, B.

    2008-11-01

    The detailed design of the Ignitor machine has been carried out by considering extended limiter plasma configurations that are up-down symmetric and whose outer magnetic surfaces follow closely the cavity of the toroidal magnet over most of the vertical cross section. This provision minimizes the out-of- plane forces produced by the plasma current and acting on the toroidal magnet. When, instead, the adopted plasma equilibrium configuration is of the double X-point type the out-of-plane forces increase, and a complete structural analysis to take this increase into account becomes appropriate. The reference maximum plasma current Ip, in order to maintain an acceptable magnetic safety factor, is reduced from 11 MA in the extended limiter to 9 MA in the double X-point configuration while the magnetic field on axis (R01.32 m) is maintained at BT13 T. The reduced scenario involving Ip6 MA and BT9 T does not present a problem. Both 3D and 2D drawings of each individual machine component are produced using the Dassault Systems CATIA-V software. After their integration into a single 3D CATIA model of the Core (Load Assembly), the electro-fluidic and fluidic lines which supply electrical currents and helium cooling gas to the coils are included and mechanically connected to the main machine components.^*Sponsored in part by ENEA of Italy and by the U.S. D.O.E.

  16. Manipulability measure of dual-arm space robot and its application to design an optimal configuration

    Science.gov (United States)

    Zhang, Bo; Liang, Bin; Wang, Xueqian; Li, Gang; Chen, Zhang; Zhu, Xiaojun

    2016-11-01

    Coupling effect exists among different arms and the base in a multi-arm space robot. The manipulability measure of one arm can be affected by the base and the other arms, which has important effects on the configuration optimization, the singularity avoidance and the compliant control. The manipulability measure for a multi-arm space robot is more complex than that of a single-arm space robot. At present, the manipulability measure of a multi-arm space robot has not been studied. In the paper, a new concept of manipulability measure is applied to analyze the manipulability measure for a dual-arm space robot, especially for the manipulability measure of the mission arm subjecting to the influence from coupling effect of auxiliary arm and the base. Based on the manipulability measure of mission arm, a performance index is introduced and used to design and choose an optimization configuration for a dual-arm space robot. Finally, a plane dual-arm space robot is simulated, which is illustrated the influence of joint angles and the base attitude on mission arm's manipulability measure. Simulation results show that the proposed manipulability measure is useful for a multi-arm space robot and optimal configuration can be extended and applied to the coordinated soft rendezvous and docking and the target capture in the field of on-orbit servicing.

  17. Parametric Flutter Analysis of the TCA Configuration and Recommendation for FFM Design and Scaling

    Science.gov (United States)

    Baker, Myles; Lenkey, Peter

    1997-01-01

    The current HSR Aeroelasticity plan to design, build, and test a full span, free flying transonic flutter model in the TDT has many technical obstacles that must be overcome for a successful program. One technical obstacle is the determination of a suitable configuration and point in the sky to use in setting the scaling point for the ASE models program. Determining this configuration and point in the sky requires balancing several conflicting requirements, including model buildability, tunnel test safety, and the ability of the model to represent the flutter mechanisms of interest. As will be discussed in detail in subsequent sections, the current TCA design exhibits several flutter mechanisms of interest. It has been decided that the ASE models program will focus on the low frequency symmetric flutter mechanism, and will make no attempt to investigate high frequency flutter mechanisms. There are several reasons for this choice. First, it is believed that the high frequency flutter mechanisms are similar in nature to classical wing bending/torsion flutter, and therefore there is more confidence that this mechanism can be predicted using current techniques. The low frequency mode, on the other hand, is a highly coupled mechanism involving wing, body, tail, and engine motion which may be very difficult to predict. Second, the high frequency flutter modes result in very small weight penalties (several hundred pounds), while suppression of the low frequency mechanism inside the flight envelope causes thousands of pounds to be added to the structure. In order to successfully test the low frequency flutter mode of interest, a suitable starting configuration and point in the sky must be identified. The configuration and point in the sky must result in a wind tunnel model that (1) represents the low-frequency wing/body/engine/empennage flutter mechanisms that are unique to HSCT configurations, (2) flutters at an acceptably low frequency in the tunnel, (3) flutters at an

  18. Flow Past an Accumulator Unit of an Underwater Energy Storage System:Three Touching Balloons in a Floral Configuration

    Institute of Scientific and Technical Information of China (English)

    Ahmadreza Vasel-Be-Hagh; Rupp Carriveau; David S-K Ting

    2014-01-01

    An LES simulation of flow over an accumulator unit of an underwater compressed air energy storage facility was conducted. The accumulator unit consists of three touching underwater balloons arranged in a floral configuration. The structure of the flow was examined via three dimensional iso surfaces of the Q criterion. Vortical cores were observed on the leeward surface of the balloons. The swirling tube flows generated by these vortical cores were depicted through three dimensional path lines. The flow dynamics were visualized via time series snapshots of two dimensional vorticity contours perpendicular to the flow direction;revealing the turbulent swinging motions of the aforementioned shedding-swirling tube flows. The time history of the hydrodynamic loading was presented in terms of lift and drag coefficients. Drag coefficient of each individual balloon in the floral configuration was smaller than that of a single balloon. It was found that the total drag coefficient of the floral unit of three touching balloons, i.e. summation of the drag coefficients of the balloons, is not too much larger than that of a single balloon whereas it provides three times the storage capacity. In addition to its practical significance in designing appropriate foundation and supports, the instantaneous hydrodynamic loading was used to determine the frequency of the turbulent swirling-swinging motions of the shedding vortex tubes;the Strouhal number was found to be larger than that of a single sphere at the same Reynolds number.

  19. Performance analysis of different ORC configurations for thermal energy and LNG cold energy hybrid power generation system

    Science.gov (United States)

    Sun, Zhixin; Wang, Feng; Wang, Shujia; Xu, Fuquan; Lin, Kui

    2017-01-01

    This paper presents a thermal energy and Liquefied natural gas (LNG) cold energy hybrid power generation system. Performances of four different Organic Rankine cycle (ORC) configurations (the basic, the regenerative, the reheat and the regenerative-reheat ORCs) are studied based on the first and the second law of thermodynamics. Dry organic fluid R245fa is selected as the typical working fluid. Parameter analysis is also conducted in this paper. The results show that regeneration could not increase the thermal efficiency of the thermal and cold energy hybrid power generation system. ORC with the reheat process could produce more specific net power output but it may also reduce the system thermal efficiency. The basic and the regenerative ORCs produce higher thermal efficiency while the regenerative-reheat ORC performs best in the exergy efficiency. A preheater is necessary for the thermal and cold energy hybrid power generation system. And due to the presence of the preheater, there will be a step change of the system performance as the turbine inlet pressure rises.

  20. Shift to a low carbon society through energy systems design

    Institute of Scientific and Technical Information of China (English)

    Toshihiko; NAKATA; Mikhail; RODIONOV; Diego; SILVA; Joni; JUPESTA

    2010-01-01

    Concern about global warming calls for an advanced approach for designing an energy system to reduce carbon emissions as well as to secure energy security for each country.Conventional energy systems tend to introduce different technologies with high conversion efficiency,leading to a higher average efficiency.Advanced energy systems can be achieved not by an aggregate form of conversion technologies but by an innovative system design itself.The concept of LCS(low carbon society) is a unique approach having multi-dimensional considerations such as social,economic and environmental dimensions.The LCS aims at an extensive restructuring of worldwide energy supply/demand network system by not only replacing the conventional parts with the new ones,but also integrating all the necessary components and designing absolutely different energy networks.As a core tool for the LCS design,energy-economic models are applied to show feasible solutions in future with alternatives such as renewable resources,combined heat and power,and smart grid operations.Models can introduce changes in energy markets,technology learning in capacity,and penetration of innovative technologies,leading to an optimum system configuration under priority settings.The paper describes recent trials of energy models application related to waste-to-energy,clean coal,transportation and rural development.Although the modelling approach is still under investigation,the output clearly shows possible options having variety of technologies and linkages between supply and demand sides.Design of the LCS means an energy systems design with the modelling approach,which gives solution for complex systems,choices among technologies,technology feasibility,R&D targets,and what we need to start.

  1. Aerodynamic Shape Sensitivity Analysis and Design Optimization of Complex Configurations Using Unstructured Grids

    Science.gov (United States)

    Taylor, Arthur C., III; Newman, James C., III; Barnwell, Richard W.

    1997-01-01

    A three-dimensional unstructured grid approach to aerodynamic shape sensitivity analysis and design optimization has been developed and is extended to model geometrically complex configurations. The advantage of unstructured grids (when compared with a structured-grid approach) is their inherent ability to discretize irregularly shaped domains with greater efficiency and less effort. Hence, this approach is ideally suited for geometrically complex configurations of practical interest. In this work the nonlinear Euler equations are solved using an upwind, cell-centered, finite-volume scheme. The discrete, linearized systems which result from this scheme are solved iteratively by a preconditioned conjugate-gradient-like algorithm known as GMRES for the two-dimensional geometry and a Gauss-Seidel algorithm for the three-dimensional; similar procedures are used to solve the accompanying linear aerodynamic sensitivity equations in incremental iterative form. As shown, this particular form of the sensitivity equation makes large-scale gradient-based aerodynamic optimization possible by taking advantage of memory efficient methods to construct exact Jacobian matrix-vector products. Simple parameterization techniques are utilized for demonstrative purposes. Once the surface has been deformed, the unstructured grid is adapted by considering the mesh as a system of interconnected springs. Grid sensitivities are obtained by differentiating the surface parameterization and the grid adaptation algorithms with ADIFOR (which is an advanced automatic-differentiation software tool). To demonstrate the ability of this procedure to analyze and design complex configurations of practical interest, the sensitivity analysis and shape optimization has been performed for a two-dimensional high-lift multielement airfoil and for a three-dimensional Boeing 747-200 aircraft.

  2. High-efficiency solar energy conversion with spectrum splitting prismatic lens (and other configurations)

    Science.gov (United States)

    Apostoleris, Harry; Maragliano, Carlo; Chiesa, Matteo; Stefancich, Marco

    2016-09-01

    Optical spectrum splitting systems that divide light between independent solar cells of different band gaps have received increasing attention in recent years as an alternative to expensive multijunction cells for high-efficiency PV. Most research, however, has focused on dichroic filters and other photonic structures that are expensive to manufacture. This has the effect of transferring the cost of the system from the PV cells to the optics. As a low-cost spectrum splitting approach we designed a prismatic lens that simultaneously splits and concentrates light and can be fabricated by injection molding. We present experimental results of a two-cell demonstration system, and calculations for low-cost configurations of commercial solar cells, enabled by the removal of lattice-matching requirements.

  3. Business model design through a designer's lens: Translating, transferring and transforming cognitive configurations into action

    NARCIS (Netherlands)

    Simonse, W.L.; Badke-Schaub, P.G.

    2015-01-01

    Strategic managers are challenged to take advantage of digitalisation opportunities related to services of social media and web 2.0 technologies. Business innovations such as crowd sourcing platforms require a new way of integrating business to technology, articulated in a new business model designs

  4. A multi-perspective approach for the design of Product Configuration Systems - an evaluation of industry applications

    DEFF Research Database (Denmark)

    Hvam, Lars

    2004-01-01

    This article presents a suggested procedure for modelling and implementation of product configuration systems. The procedure has been applied in several industrial companies. The procedure comprises: • Analysis of the business processes to be supported by a product configuration system. Furthermore......, a de-marcation and definition of the configuration system to be designed. • Analysis and modelling of the part of the company’s product assortment which is to be included in the con-figuration system. • Selection of configuration software and programming of the configuration system. • Implementation....... The procedure or certain parts of the procedure have currently been tested and further developed in cooperation with a number of industrial companies including F.L.Smidth, American Power Conversion (APC), Aalborg industries, NEG-Micon, GEA-Niro and IBM-SMS. This paper presents the experiences gained from 4...

  5. Using Computational Fluid Dynamics and Experiments to Design Sweeping Jets for High Reynolds Number Cruise Configurations

    Science.gov (United States)

    Jones, Gregory S.; Milholen, William E., II; Fell, Jared S.; Webb, Sandy R.; Cagle, C. Mark

    2016-01-01

    The application of a sweeping jet actuator to a circulation control system was initiated by a risk reduction series of experiments to optimize the authority of a single sweeping jet actuator. The sweeping jet design was integrated into the existing Fundamental Aerodynamic Subsonic Transonic- Modular Active Control (FAST-MAC) model by replacing the steady blowing system with an array of thirty-nine sweeping jet cartridges. A constant slot height to wing chord ratio was similar to the steady blowing configuration resulting in each actuator having a unique in size for the sweeping jet configuration. While this paper will describe the scaling and optimization of the actuators for future high Reynolds number applications, the major focus of this effort was to target the transonic flight regime by increasing the amplitude authority of the actuator. This was accomplished by modifying the diffuser of the sweeping jet actuator, and this paper highlights twelve different diffuser designs. The experimental portion of this work was completed in the NASA Langley National Transonic Facility.

  6. DESIGNING THE OPTIMUM CONFIGURATIONS OF CIRCULAR AND SPHERICAL PRODUCT SPECIFICATIONS FOR MULTIPLE QUALITY CHARACTERISTICS

    Institute of Scientific and Technical Information of China (English)

    Byung Rae CHO; Michael D. PHILLIPS; Jami KOVACH

    2005-01-01

    As an integral part of tolerance design in the context of design for six sigma, determining optimal product specifications has become the focus of increased activity, as manufacturing industries strive to increase productivity and improve the quality of their products. Although a number of research papers have been reported in the research community, there is room for improvement. Most existing research papers consider determining optimal specification limits for a single quality characteristic. In this paper, we develop the modeling and optimization procedures for optimum circular and spherical configurations by considering multiple quality characteristics. The concepts of multivariate quality loss function and truncated distribution are incorporated. This has never been adequately addressed, nor has been appropriately applied in industry. A numerical example is shown and comparison studies are made.

  7. Fluorescence Resonance Energy Transfer Analysis of Recombination Signal Sequence Configuration in the RAG1/2 Synaptic Complex▿ †

    OpenAIRE

    Ciubotaru, Mihai; Kriatchko, Aleksei N.; Swanson, Patrick C.; Bright, Frank V.; Schatz, David G.

    2007-01-01

    A critical step in V(D)J recombination is the synapsis of complementary (12/23) recombination signal sequences (RSSs) by the RAG1 and RAG2 proteins to generate the paired complex (PC). Using a facilitated ligation assay and substrates that vary the helical phasing of the RSSs, we provide evidence that one particular geometric configuration of the RSSs is favored in the PC. To investigate this configuration further, we used fluorescent resonance energy transfer (FRET) to detect the synapsis of...

  8. Energy efficient wireless ATM design

    NARCIS (Netherlands)

    Havinga, Paul J.M.; Smit, Gerardus Johannes Maria; Bos, M.

    1999-01-01

    Energy efficiency is an important issue for mobile computers since they must rely on their batteries. We present an architecture for wireless ATM and a novel MAC protocol that achieves a good energy efficiency of the wireless interface of the mobile and provides QoS support for diverse traffic

  9. Energy efficient wireless ATM design

    NARCIS (Netherlands)

    Havinga, Paul J.M.; Smit, Gerardus Johannes Maria; Bos, M.

    2000-01-01

    Energy efficiency is an important issue for mobile computers since they must rely on their batteries. We present an energy-efficient highly adaptive architecture of a network interface and novel data link layer protocol for wireless networks that provides Quality of Service (QoS) support for diverse

  10. Energy management of electric and hybrid vehicles dependent on powertrain configuration

    Science.gov (United States)

    Varga, Bogdan

    2012-06-01

    Electric and hybrid vehicles are going to become the most reliable source of transport for future years. The CO2 and NOx targets in Euro 6 normative puts the producers of vehicles in a dilemma, whether to adapt the internal combustion engines further, or to develop hybrid or electric power trains that are going to reach the pollution limit of the future norms or to go below that. Before acting a well-developed strategy in determining the optimum power flow has to be developed by producers; CRUISE software is a tool with the unique and special characteristics to determine the optimum in this highly important area. Whether electric vehicle, electric vehicle with range extender or a hybrid with CVT or planetary gearbox, the complexity of the mathematical modules remains the same, giving the developer the possibility to create complex functions and distinctive characteristics for each component of the vehicle. With such a powerful tool it becomes extremely easy to evaluate the energy flow in all directions, from electric machine to the battery, from electric machine to the power generator, and from the electric machine to the internal combustion engine. Applying to the (Electric Vehicle, Electric Vehicle with Range Extender, Hybrid vehicle with CVT, Hybrid vehicle with planetary gear set) the ECE-15 in a virtual environment (urban driving cycle) the simulation results show a different usage, rate of storage and efficiency concerning the energy, this being dependent of the power train configuration in most part.

  11. Application of Optimization Techniques to Design of Unconventional Rocket Nozzle Configurations

    Science.gov (United States)

    Follett, W.; Ketchum, A.; Darian, A.; Hsu, Y.

    1996-01-01

    Several current rocket engine concepts such as the bell-annular tri-propellant engine, and the linear aerospike being proposed for the X-33 require unconventional three dimensional rocket nozzles which must conform to rectangular or sector shaped envelopes to meet integration constraints. These types of nozzles exist outside the current experience database, therefore, the application of efficient design methods for these propulsion concepts is critical to the success of launch vehicle programs. The objective of this work is to optimize several different nozzle configurations, including two- and three-dimensional geometries. Methodology includes coupling computational fluid dynamic (CFD) analysis to genetic algorithms and Taguchi methods as well as implementation of a streamline tracing technique. Results of applications are shown for several geometeries including: three dimensional thruster nozzles with round or super elliptic throats and rectangualar exits, two- and three-dimensional thrusters installed within a bell nozzle, and three dimensional thrusters with round throats and sector shaped exits. Due to the novel designs considered for this study, there is little experience which can be used to guide the effort and limit the design space. With a nearly infinite parameter space to explore, simple parametric design studies cannot possibly search the entire design space within the time frame required to impact the design cycle. For this reason, robust and efficient optimization methods are required to explore and exploit the design space to achieve high performance engine designs. Five case studies which examine the application of various techniques in the engineering environment are presented in this paper.

  12. Energy manager design for microgrids

    Energy Technology Data Exchange (ETDEWEB)

    Firestone, Ryan; Marnay, Chris

    2005-01-01

    On-site energy production, known as distributed energy resources (DER), offers consumers many benefits, such as bill savings and predictability, improved system efficiency, improved reliability, control over power quality, and in many cases, greener electricity. Additionally, DER systems can benefit electric utilities by reducing congestion on the grid, reducing the need for new generation and transmission capacity, and offering ancillary services such as voltage support and emergency demand response. Local aggregations of distributed energy resources (DER) that may include active control of on-site end-use energy devices can be called microgrids. Microgrids require control to ensure safe operation and to make dispatch decisions that achieve system objectives such as cost minimization, reliability, efficiency and emissions requirements, while abiding by system constraints and regulatory rules. This control is performed by an energy manager (EM). Preferably, an EM will achieve operation reasonably close to the attainable optimum, it will do this by means robust to deviations from expected conditions, and it will not itself incur insupportable capital or operation and maintenance costs. Also, microgrids can include supervision over end-uses, such as curtailing or rescheduling certain loads. By viewing a unified microgrid as a system of supply and demand, rather than simply a system of on-site generation devices, the benefits of integrated supply and demand control can be exploited, such as economic savings and improved system energy efficiency.

  13. Hypersonic Separated Flows About "Tick" Configurations With Sensitivity to Model Design

    Science.gov (United States)

    Moss, J. N.; O'Byrne, S.; Gai, S. L.

    2014-01-01

    This paper presents computational results obtained by applying the direct simulation Monte Carlo (DSMC) method for hypersonic nonequilibrium flow about "tick-shaped" model configurations. These test models produces a complex flow where the nonequilibrium and rarefied aspects of the flow are initially enhanced as the flow passes over an expansion surface, and then the flow encounters a compression surface that can induce flow separation. The resulting flow is such that meaningful numerical simulations must have the capability to account for a significant range of rarefaction effects; hence the application of the DSMC method in the current study as the flow spans several flow regimes, including transitional, slip, and continuum. The current focus is to examine the sensitivity of both the model surface response (heating, friction and pressure) and flowfield structure to assumptions regarding surface boundary conditions and more extensively the impact of model design as influenced by leading edge configuration as well as the geometrical features of the expansion and compression surfaces. Numerical results indicate a strong sensitivity to both the extent of the leading edge sharpness and the magnitude of the leading edge bevel angle. Also, the length of the expansion surface for a fixed compression surface has a significant impact on the extent of separated flow.

  14. Optimization of the core configuration design using a hybrid artificial intelligence algorithm for research reactors

    Energy Technology Data Exchange (ETDEWEB)

    Hedayat, Afshin, E-mail: ahedayat@aut.ac.i [Department of Nuclear Engineering and Physics, Amirkabir University of Technology (Tehran Polytechnic), 424 Hafez Avenue, P.O. Box 15875-4413, Tehran (Iran, Islamic Republic of); Reactor Research and Development School, Nuclear Science and Technology Research Institute (NSTRI), End of North Karegar Street, P.O. Box 14395-836, Tehran (Iran, Islamic Republic of); Davilu, Hadi [Department of Nuclear Engineering and Physics, Amirkabir University of Technology (Tehran Polytechnic), 424 Hafez Avenue, P.O. Box 15875-4413, Tehran (Iran, Islamic Republic of); Barfrosh, Ahmad Abdollahzadeh [Department of Computer Engineering, Amirkabir University of Technology (Tehran Polytechnic), 424 Hafez Avenue, P.O. Box 15875-4413, Tehran (Iran, Islamic Republic of); Sepanloo, Kamran [Reactor Research and Development School, Nuclear Science and Technology Research Institute (NSTRI), End of North Karegar Street, P.O. Box 14395-836, Tehran (Iran, Islamic Republic of)

    2009-12-15

    To successfully carry out material irradiation experiments and radioisotope productions, a high thermal neutron flux at irradiation box over a desired life time of a core configuration is needed. On the other hand, reactor safety and operational constraints must be preserved during core configuration selection. Two main objectives and two safety and operational constraints are suggested to optimize reactor core configuration design. Suggested parameters and conditions are considered as two separate fitness functions composed of two main objectives and two penalty functions. This is a constrained and combinatorial type of a multi-objective optimization problem. In this paper, a fast and effective hybrid artificial intelligence algorithm is introduced and developed to reach a Pareto optimal set. The hybrid algorithm is composed of a fast and elitist multi-objective genetic algorithm (GA) and a fast fitness function evaluating system based on the cascade feed forward artificial neural networks (ANNs). A specific GA representation of core configuration and also special GA operators are introduced and used to overcome the combinatorial constraints of this optimization problem. A software package (Core Pattern Calculator 1) is developed to prepare and reform required data for ANNs training and also to revise the optimization results. Some practical test parameters and conditions are suggested to adjust main parameters of the hybrid algorithm. Results show that introduced ANNs can be trained and estimate selected core parameters of a research reactor very quickly. It improves effectively optimization process. Final optimization results show that a uniform and dense diversity of Pareto fronts are gained over a wide range of fitness function values. To take a more careful selection of Pareto optimal solutions, a revision system is introduced and used. The revision of gained Pareto optimal set is performed by using developed software package. Also some secondary operational

  15. Development and benefit analysis of a sector design algorithm for terminal dynamic airspace configuration

    Science.gov (United States)

    Sciandra, Vincent

    performance of the algorithm generated sectors to the current sectors for a variety of configurations and scenarios, and comparing these results to those of the current sectors. The effect of dynamic airspace configurations will then be tested by observing the effects of update rate on the algorithm generated sector results. Finally, the algorithm will be used with simulated data, whose evaluation would show the ability of the sector design algorithm to meet the objectives of the NextGen system. Upon validation, the algorithm may be successfully incorporated into a larger Terminal Flow Algorithm, developed by our partners at Mosaic ATM, as the final step in the TDAC process.

  16. Design of energy management indicator.

    OpenAIRE

    Ernesto Tomás Dalmau García; Carlos Requejo Bravo; Roberto Fernández Collado

    2010-01-01

    This work has as a main goal to demostrate the viability of the energy management indicator, that will be a part of the Balanced Scorecard in the organization and the own process of calculation allows to obtain a Balanced Scorecard of energy management. It describes the executive order of the actions that have to be done to reach to the mentioned indicator, based on the selection of the selected period of time; the types of power carriers, the weight of each carrier in the structure of the c...

  17. Solar Energy: Solar System Design Fundamentals.

    Science.gov (United States)

    Knapp, Henry H., III

    This module on solar system design fundamentals is one of six in a series intended for use as supplements to currently available materials on solar energy and energy conservation. Together with the recommended texts and references (sources are identified), these modules provide an effective introduction to energy conservation and solar energy…

  18. Utilization of renewable energy in architectural design

    Institute of Scientific and Technical Information of China (English)

    TIAN Lei; QIN Youguo

    2007-01-01

    Renewable energy does not simply equal to using a photovoltaic (PV) board.In addition to heating,ventilation and air conditioning (HVAC) engineering considerations,the design approaches of architects are crucial to the utilization condition and methods of renewable energy.Through profound comprehension of the relationship between renewable energy utilization and design approaches,we can achieve a dual-standard of building environment performance and esthetics.

  19. 50% Advanced Energy Design Guides: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Bonnema, E.; Leach, M.; Pless, S.; Liu, B.; Wang, W.; Thornton, B.; Williams, J.

    2012-07-01

    This paper presents the process, methodology, and assumptions for the development of the 50% Energy Savings Advanced Energy Design Guides (AEDGs), a design guidance document that provides specific recommendations for achieving 50% energy savings above the requirements of ANSI/ASHRAE/IESNA Standard 90.1-2004 in four building types: (1) Small to medium office buildings, (2) K-12 school buildings, (3) Medium to big box retail buildings, (4) Large hospital buildings.

  20. A Zeeman slower design with permanent magnets in a Halbach configuration.

    Science.gov (United States)

    Cheiney, P; Carraz, O; Bartoszek-Bober, D; Faure, S; Vermersch, F; Fabre, C M; Gattobigio, G L; Lahaye, T; Guéry-Odelin, D; Mathevet, R

    2011-06-01

    We describe a simple Zeeman slower design using permanent magnets. Contrary to common wire-wound setups, no electric power and water cooling are required. In addition, the whole system can be assembled and disassembled at will. The magnetic field is however transverse to the atomic motion and an extra repumper laser is necessary. A Halbach configuration of the magnets produces a high quality magnetic field and no further adjustment is needed. After optimization of the laser parameters, the apparatus produces an intense beam of slow and cold (87)Rb atoms. With typical fluxes of (1-5) × 10(10) atoms/s at 30 m s(-1), our apparatus efficiently loads a large magneto-optical trap with more than 10(10) atoms in 1 s, which is an ideal starting point for degenerate quantum gas experiments.

  1. Design guidelines of triboelectric nanogenerator for water wave energy harvesters

    Science.gov (United States)

    Ahmed, Abdelsalam; Hassan, Islam; Jiang, Tao; Youssef, Khalid; Liu, Lian; Hedaya, Mohammad; Abu Yazid, Taher; Zu, Jean; Wang, Zhong Lin

    2017-05-01

    Ocean waves are one of the cleanest and most abundant energy sources on earth, and wave energy has the potential for future power generation. Triboelectric nanogenerator (TENG) technology has recently been proposed as a promising technology to harvest wave energy. In this paper, a theoretical study is performed on a duck-shaped TENG wave harvester recently introduced in our work. To enhance the design of the duck-shaped TENG wave harvester, the mechanical and electrical characteristics of the harvester’s overall structure, as well as its inner configuration, are analyzed, respectively, under different wave conditions, to optimize parameters such as duck radius and mass. Furthermore, a comprehensive hybrid 3D model is introduced to quantify the performance of the TENG wave harvester. Finally, the influence of different TENG parameters is validated by comparing the performance of several existing TENG wave harvesters. This study can be applied as a guideline for enhancing the performance of TENG wave energy harvesters.

  2. Design guidelines of triboelectric nanogenerator for water wave energy harvesters

    KAUST Repository

    Ahmed, Abdelsalam

    2017-04-11

    Ocean waves are one of the cleanest and most abundant energy sources on earth, and wave energy has the potential for future power generation. Triboelectric nanogenerator (TENG) technology has recently been proposed as a promising technology to harvest wave energy. In this paper, a theoretical study is performed on a duck-shaped TENG wave harvester recently introduced in our work. To enhance the design of the duck-shaped TENG wave harvester, the mechanical and electrical characteristics of the harvester\\'s overall structure, as well as its inner configuration, are analyzed, respectively, under different wave conditions, to optimize parameters such as duck radius and mass. Furthermore, a comprehensive hybrid 3D model is introduced to quantify the performance of the TENG wave harvester. Finally, the influence of different TENG parameters is validated by comparing the performance of several existing TENG wave harvesters. This study can be applied as a guideline for enhancing the performance of TENG wave energy harvesters.

  3. CFD Analysis and Design of Detailed Target Configurations for an Accelerator-Driven Subcritical System

    Energy Technology Data Exchange (ETDEWEB)

    Kraus, Adam; Merzari, Elia; Sofu, Tanju; Zhong, Zhaopeng; Gohar, Yousry

    2016-08-01

    High-fidelity analysis has been utilized in the design of beam target options for an accelerator driven subcritical system. Designs featuring stacks of plates with square cross section have been investigated for both tungsten and uranium target materials. The presented work includes the first thermal-hydraulic simulations of the full, detailed target geometry. The innovative target cooling manifold design features many regions with complex flow features, including 90 bends and merging jets, which necessitate three-dimensional fluid simulations. These were performed using the commercial computational fluid dynamics code STAR-CCM+. Conjugate heat transfer was modeled between the plates, cladding, manifold structure, and fluid. Steady-state simulations were performed but lacked good residual convergence. Unsteady simulations were then performed, which converged well and demonstrated that flow instability existed in the lower portion of the manifold. It was established that the flow instability had little effect on the peak plate temperatures, which were well below the melting point. The estimated plate surface temperatures and target region pressure were shown to provide sufficient margin to subcooled boiling for standard operating conditions. This demonstrated the safety of both potential target configurations during normal operation.

  4. A knowledge management methodology for the integrated assessment of WWTP configurations during conceptual design.

    Science.gov (United States)

    Garrido-Baserba, M; Reif, R; Rodriguez-Roda, I; Poch, M

    2012-01-01

    The current complexity involved in wastewater management projects is arising as the XXI century sets new challenges leading towards a more integrated plant design. In this context, the growing number of innovative technologies, stricter legislation and the development of new methodological approaches make it difficult to design appropriate flow schemes for new wastewater projects. Thus, new tools are needed for the wastewater treatment plant (WWTP) conceptual design using integrated assessment methods in order to include different types of objectives at the same time i.e. environmental, economical, technical, and legal. Previous experiences used the decision support system (DSS) methodology to handle the specific issues related to wastewater management, for example, the design of treatment facilities for small communities. However, tools developed for addressing the whole treatment process independently of the plant size, capable of integrating knowledge from many different areas, including both conventional and innovative technologies are not available. Therefore, the aim of this paper is to present and describe an innovative knowledge-based methodology that handles the conceptual design of WWTP process flow-diagrams (PFDs), satisfying a vast number of different criteria. This global approach is based on a hierarchy of decisions that uses the information contained in knowledge bases (KBs) with the aim of automating the generation of suitable WWTP configurations for a specific scenario. Expert interviews, legislation, specialized literature and engineering experience have been integrated within the different KBs, which indeed constitute one of the main highlights of this work. Therefore, the methodology is presented as a valuable tool which provides customized PFD for each specific case, taking into account process unit interactions and the user specified requirements and objectives.

  5. Optimized design of low energy buildings

    DEFF Research Database (Denmark)

    Rudbeck, Claus Christian; Esbensen, Peter Kjær; Svendsen, Sv Aa Højgaard

    1999-01-01

    by 33% compared to current level and that the CO2 emission should be halved. This calls for sustainable development in the building sector, but at the same time, it has to be economically efficient. People are conscious about savings in energy, but consideration to economic aspects are their primary...... concern which can be seen during the construction of new buildings. People want energy-friendly solutions, but they should be economical optimized. An exonomical optimized building design with respect to energy consumption is the design with the lowest total cost (investment plus operational cost over its...... life time). The design and construction of buildings should take into account both energy, environment and economical aspects. The design of a building is very complex and the work on optimizing the design raises several questions. Which criteria are the decisive when choosing a solution? How...

  6. Amine Solvent Regeneration for CO2 Capture Using Geothermal Energy with Advanced Stripper Configurations

    Directory of Open Access Journals (Sweden)

    Van Wagener D.H.

    2014-11-01

    Full Text Available Absorption/stripping using alkanolamine solvents for removing CO2 from the flue gas of coal-fired power plants requires a substantial amount of energy. Typical designs anticipate the use of steam extraction between the Intermediate Pressure (IP and Low Pressure (LP turbines to provide heat for the reboiler. Geothermal energy in the form of hot brine offers an alternative to this large parasitic load on the power generation cycle. We investigate the requirements (number and spacing of extraction/injection well pairs to provide heat at 150°C for a pilot scale (60 MWe and a full scale (900 MWe capture process for thirty years. The calculations are based on properties of a geopressured/geothermal aquifer near the Texas Gulf Coast. In the vicinity of a large coal-fired power plant in South Texas, this aquifer lies between 3 050 and 3 350 m (10 000 and 11 000 ft below the surface. We present a novel design of the stripper/regenerator process based on heat exchange with the brine, discharging the brine at 100°C. The results indicate that the overall process is feasible and that costs are of similar magnitude to standard designs.

  7. EnergyFacade - Operational energy optimisation for conceptual facade design

    NARCIS (Netherlands)

    Heidegger, V.; Coenders, J.L.; Rolvink, A.

    2014-01-01

    This paper presents the results of the investigation into the possibilities for the implementation of a Building Performance Simulation design toolbox during the early stages of façade design, based on the sustainability-open framework [2]. The background and development of the EnergyFacade toolbox

  8. EnergyFacade - Operational energy optimisation for conceptual facade design

    NARCIS (Netherlands)

    Heidegger, V.; Coenders, J.L.; Rolvink, A.

    2014-01-01

    This paper presents the results of the investigation into the possibilities for the implementation of a Building Performance Simulation design toolbox during the early stages of façade design, based on the sustainability-open framework [2]. The background and development of the EnergyFacade toolbox

  9. New Topological Configurations in the Continuous Heisenberg Spin Chain: Lower Bound for the Energy

    Directory of Open Access Journals (Sweden)

    Rossen Dandoloff

    2015-01-01

    Full Text Available In order to study the spin configurations of the classical one-dimensional Heisenberg model, we map the normalized unit vector, representing the spin, on a space curve. We show that the total chirality of the configuration is a conserved quantity. If, for example, one end of the space curve is rotated by an angle of 2π relative to the other, the Frenet frame traces out a noncontractible loop in SO(3 and this defines a new class of topological spin configurations for the Heisenberg model.

  10. Potential Energy Surface in Hartree-Fock Theory:Adiabatic or Configuration-Constrained?

    Institute of Scientific and Technical Information of China (English)

    GUO Lu; Sakata Fumihiko; ZHAO En-Guang

    2004-01-01

    Validity of adiabatic assumption is discussed within the constrained Hartree-Fock theory for self-conjugate nucleus 72Kr. It is shown that the adiabatic assumption does not provide a correct description for the nature of nucleus when a configuration change is involved. The excited Hartree-Fock states and the continuously-connected constrained Hartree-Fock states are given for the first time by applying the configuration dictated constrained Hartree-Fock theory with Gogny force. The importance of self-consistency between the mean-field and the single particle wave functions is emphasized even when a small number of nucleons are involved in the configuration change.

  11. Scaled Second Order Perturbation Corrections to Configuration Interaction Singles: Efficient and Reliable Excitation Energy Methods

    Energy Technology Data Exchange (ETDEWEB)

    Rhee, Young Min; Head-Gordon, Martin

    2007-02-01

    Two modifications of the perturbative doubles correction to configuration interaction with single substitutions (CIS(D)) are suggested, which are excited state analogs of ground state scaled second order Moeller-Plesset (MP2) methods. The first approach employs two parameters to scale the two spin components of the direct term of CIS(D), starting from the two-parameter spin-component scaled (SCS) MP2 ground state, and is termed SCS-CIS(D). An efficient resolution-of-the-identity (RI) implementation of this approach is described. The second approach employs a single parameter to scale only the opposite-spin direct term of CIS(D), starting from the one-parameter scaled opposite spin (SOS) MP2 ground state, and is called SOS-CIS(D). By utilizing auxiliary basis expansions and a Laplace transform, a fourth order algorithm for SOS-CIS(D) is described and implemented. The parameters describing SCS-CIS(D) and SOS-CIS(D) are optimized based on a training set including valence excitations of various organic molecules and Rydberg transitions of water and ammonia, and they significantly improve upon CIS(D) itself. The accuracy of the two methods is found to be comparable. This arises from a strong correlation between the same-spin and opposite-spin portions of the excitation energy terms. The methods are successfully applied to the zincbacteriochlorin-bacteriochlorin charge transfer transition, for which time-dependent density functional theory, with presently available exchange-correlation functionals, is known to fail. The methods are also successfully applied to describe various electronic transitions outside of the training set. The efficiency of SOS-CIS(D) and the auxiliary basis implementation of CIS(D) and SCS-CIS(D) are confirmed with a series of timing tests.

  12. Effect of rotor configuration on guyed tower and foundation designs and estimated costs for intermediate site horizontal axis wind turbines

    Science.gov (United States)

    Frederick, G. R.; Winemiller, J. R.; Savino, J. M.

    1982-01-01

    Three designs of a guyed cylindrical tower and its foundation for an intermediate size horizontal axis wind turbine generator are discussed. The primary difference in the three designs is the configuration of the rotor. Two configurations are two-blade rotors with teetering hubs - one with full span pitchable blades, the other with fixed pitch blades. The third configuration is a three-bladed rotor with a rigid hub and fixed pitch blades. In all configurations the diameter of the rotor is 38 meters and the axis of rotation is 30.4 meters above grade, and the power output is 200 kW and 400 kW. For each configuration the design is based upon for the most severe loading condition either operating wind or hurricane conditions. The diameter of the tower is selected to be 1.5 meters (since it was determined that this would provide sufficient space for access ladders within the tower) with guy rods attached at 10.7 meters above grade. Completing a design requires selecting the required thicknesses of the various cylindrical segments, the number and diameter of the guy rods, the number and size of soil anchors, and the size of the central foundation. The lower natural frequencies of vibration are determined for each design to ensure that operation near resonance does not occur. Finally, a cost estimate is prepared for each design. A preliminary design and cost estimate of a cantilever tower (cylindrical and not guyed) and its foundation is also presented for each of the three configurations.

  13. Technical Design of Flexible Sustainable Energy Systems

    DEFF Research Database (Denmark)

    Lund, Henrik

    2003-01-01

    The paper presents technical designs of potential future flexible energy systems in Denmark, which will be able both to balance production and demand and to secure voltage and frequency requirements on the grid.......The paper presents technical designs of potential future flexible energy systems in Denmark, which will be able both to balance production and demand and to secure voltage and frequency requirements on the grid....

  14. Configurational space discretization and free energy calculation in complex molecular systems.

    Science.gov (United States)

    Wang, Kai; Long, Shiyang; Tian, Pu

    2016-03-14

    We sought to design a free energy calculation scheme with the hope of saving cost for generating dynamical information that is inherent in trajectories. We demonstrated that snapshots in a converged trajectory set are associated with implicit conformers that have invariant statistical weight distribution (ISWD). Since infinite number of sets of implicit conformers with ISWD may be created through independent converged trajectory sets, we hypothesized that explicit conformers with ISWD may be constructed for complex molecular systems through systematic increase of conformer fineness, and tested the hypothesis in lipid molecule palmitoyloleoylphosphatidylcholine (POPC). Furthermore, when explicit conformers with ISWD were utilized as basic states to define conformational entropy, change of which between two given macrostates was found to be equivalent to change of free energy except a mere difference of a negative temperature factor, and change of enthalpy essentially cancels corresponding change of average intra-conformer entropy. By implicitly taking advantage of entropy enthalpy compensation and forgoing all dynamical information, constructing explicit conformers with ISWD and counting thermally accessible number of which for interested end macrostates is likely to be an efficient and reliable alternative end point free energy calculation strategy.

  15. Configurational Entropy,Diffusivity and Potential Energy Landscape in Liquid Argon

    Institute of Scientific and Technical Information of China (English)

    DUAN Yong-Ping; MA Cong-Xiao; LI Jia-Yun; LI Cong; WANG Dan; LI Mei-Li; SUN Min-Hua

    2009-01-01

    The configurational entropy, diffusion coefficient, dynamics and thermodynamics fragility indices of liquid argon are calculated using molecular dynamics simulations at two densities. The relationship between dynamics and thermodynamics properties is studied. The diffusion coefficient depends linearly on configurational entropy, which is consistent with the hypothesis of Adam-Gibbs. The consistence of dynamics and thermodynamics fragility indices demonstrates that dynamical behaviour is governed by thermodynamics behaviour in glass transition of liquid argon.

  16. Integrated Energy Design of the Building Envelope

    DEFF Research Database (Denmark)

    Nielsen, Martin Vraa

    project analysed how the implementation of technical knowledge early in the building design process can quantify the effect of a building’s façades on its energy efficiency and indoor climate and thereby facilitate a more qualified design development. The project was structured in the following way: 1......This thesis describes the outcome of the PhD project Integrated energy design of the building envelope carried out through a combination of scientific dissemination reported through peer-reviewed journals and a wide range of affiliated projects involved in at an architectural firm. The research...... layout, window geometry and transparency, design of the window aperture, etc. Through the wide range of affiliated project involved in at the architectural firm over the course of this project, this approach resulted in building designs with an energy demand at least 25% below the minimum requirements...

  17. Designing the Nuclear Energy Attitude Scale.

    Science.gov (United States)

    Calhoun, Lawrence; And Others

    1988-01-01

    Presents a refined method for designing a valid and reliable Likert-type scale to test attitudes toward the generation of electricity from nuclear energy. Discusses various tests of validity that were used on the nuclear energy scale. Reports results of administration and concludes that the test is both reliable and valid. (CW)

  18. Designing the Nuclear Energy Attitude Scale.

    Science.gov (United States)

    Calhoun, Lawrence; And Others

    1988-01-01

    Presents a refined method for designing a valid and reliable Likert-type scale to test attitudes toward the generation of electricity from nuclear energy. Discusses various tests of validity that were used on the nuclear energy scale. Reports results of administration and concludes that the test is both reliable and valid. (CW)

  19. Steps to design a household energy game

    NARCIS (Netherlands)

    Fijnheer, J.D.L.; van Oostendorp, H.

    2016-01-01

    Research where gamification is used to influence household energy consumption is an emerging field. This paper reviews the design and effectiveness of ten games that aim to influence household energy consumption and presents a novel gamification approach in which real world activities are

  20. Structural Earthquake Resistance Design Using Energy Method

    Institute of Scientific and Technical Information of China (English)

    Hu Rongrong

    2003-01-01

    A summary of status of researches in the field of structural earthquake resistance design on energy concept is presented in three parts: earthquake input, demands on the structure and supplied capacity of the structure. A new approach is proposed for analysis of the seismic response and damage criteria based on the momentary input energy.

  1. Design of low-energy building and energy consumption analyses

    Institute of Scientific and Technical Information of China (English)

    刘鸣; 陈滨; 范悦; 朱佳音; 索健

    2009-01-01

    In China,a new "Design standard for energy efficiency of residential buildings (for cold region)" was introduced in 2006. In this new standard,more high level insulation of the building envelope is required,yearly energy requirement for heating must be less than 55 kWh/(m2·a)(regarded as a low-energy house). The new attempt was carried out in the process of architecture design with an evaluation on energy consumption of the building. The design plan was brought forward and compared. PHPP software from German was applied to calculate energy consumption of the passive residential building. The optimum design planning was discussed and model of passive house suited to China’s national conditions were attempted. The compactness,solar air collector and the window-wall ratio have essential influence on the energy consumption of buildings. The annual heat demands for the buildings with the window-wall ratio 0.35 and 0.50 are 48 kWh/(m2·a) and 46 kWh/(m2·a),respectively. The yearly auxiliary heat of building with the wall-mounted solar air collectors and the window-wall ratio 0.35 is just 4.8 kWh/(m2·a).

  2. Integrated Energy Design in Master Planning

    DEFF Research Database (Denmark)

    Strømann-Andersen, Jakob Bjørn

    of opportunities and limitations with regard to light, shade, sun and wind. The aim is threefold: (1) to unfold the link between building energy use and urban density, typology and fabric; (2) to analyse how technical scientific knowledge can be integrated in early urban planning and design decisions (IED); and (3...... in character as daylight is taken into account. Furthermore the results suggest that there are limits to urban densification (200-300%) as an energy optimization strategy. The solar energy and daylight potential should be considered, and indeed protected, as a common resource in urban design. The most...

  3. An autonomic approach to configure HEP (High Energy Physics) experiments, applied to LHCb (Large Hadron Collider beauty)

    CERN Document Server

    Abadie, L; Charpentier, P

    2006-01-01

    Properly configuring an HEP (High Energy Phys ics) experiment becomes a more and more complex task as the number of electronics modules grows and technologies evolve quickly. Anticipating a fault in the software or in the hardware during the configuration or the data taking requires an adaptive and modular control system. The introduction of autonomic tools and data bases in the HEP world is quite recent and contributes to implement a more reliable system . The LHCb control system innovates as it has been built using autonomic tools. The main contribution of this PhD is the implementation of an autonomic 3-Tier architectur e to configure the LHCb experiment which is a huge network of devices of different types, and its integrat ion in the control system. This new type of autonomics architecture consists of: • A database layer. A relational Oracle databa se implemented using the Oracle technology contains the information...

  4. Designing Holistic Zero Energy Homes in Denmark

    DEFF Research Database (Denmark)

    Bejder, Anne Kirkegaard; Knudstrup, Mary-Ann

    2016-01-01

    , however, designing ZEBs is still challenging. In order to gain further currency, we need to collect new knowledge and communicate it in an easy applicable way for the building industry. This paper presents the development and objectives of a publication entitled “Zero Energy Buildings – Design Principles...... of zero energy houses, and identifies technical and architectural potentials and challenges related to the application of these. The publication argues that the key issue is to design the buildings through a cross-disciplinary approach to architecture and based on an integrated design process. The project...... and Built Examples for Detached Houses” with a long-term perspective heading towards 2035 building design and targeting practicing architects and engineers as well as developers. The publication introduces a number of design strategies and technologies which are particularly important for the development...

  5. Energy Efficient Design for Body Sensor Nodes

    Directory of Open Access Journals (Sweden)

    Yanqing Zhang

    2011-04-01

    Full Text Available This paper describes the hardware requirements and design constraints that derive from unique features of body sensor networks (BSNs. Based on the BSN requirements, we examine the tradeoff between custom hardware and commercial off the shelf (COTS designs for BSNs. The broad range of BSN applications includes situations where either custom chips or COTS design is optimal. For both types of nodes, we survey key techniques to improve energy efficiency in BSNs and identify general approaches to energy efficiency in this space.

  6. Optimized design of low energy buildings

    DEFF Research Database (Denmark)

    Rudbeck, Claus Christian; Esbensen, Peter Kjær; Svendsen, Sv Aa Højgaard

    1999-01-01

    concern which can be seen during the construction of new buildings. People want energy-friendly solutions, but they should be economical optimized. An exonomical optimized building design with respect to energy consumption is the design with the lowest total cost (investment plus operational cost over its...... to evaluate different separate solutions when they interact in the building.When trying to optimize several parameters there is a need for a method, which will show the correct price-performance of each part of a building under design. The problem with not having such a method will first be showed...

  7. Steps to Design a Household Energy Game

    Directory of Open Access Journals (Sweden)

    Jan Dirk Fijnheer

    2016-09-01

    Full Text Available Research where gamification is used to influence household energy consumption is an emerging field. This paper reviews the design and effectiveness of ten games that aim to influence household energy consumption and presents a novel gamification approach in which real world activities are implemented in a game design. From the review suggestions for the design of a new game have been identified, such as including real life missions in order to optimize the transfer between the game world and the real world, feedback from monitoring the electricity meter, the presence of a strong storyline, personalized game characters, social interaction, etc. Based on this comparative analysis, the new game 'Powersaver Game' focused on reducing energy consumption has been designed and its prototype is described. In the next stage of iterative design, end-users evaluated the match between in-game scenes and household energy saving activities. This considerate user-centered design process should allow us to build a serious game that is potentially effective in reducing household energy consumption. 

  8. Electronically configured battery pack

    Energy Technology Data Exchange (ETDEWEB)

    Kemper, D.

    1997-03-01

    Battery packs for portable equipment must sometimes accommodate conflicting requirements to meet application needs. An electronically configurable battery pack was developed to support two highly different operating modes, one requiring very low power consumption at a low voltage and the other requiring high power consumption at a higher voltage. The configurable battery pack optimizes the lifetime and performance of the system by making the best use of all available energy thus enabling the system to meet its goals of operation, volume, and lifetime. This paper describes the cell chemistry chosen, the battery pack electronics, and tradeoffs made during the evolution of its design.

  9. Signatures of distinct impurity configurations in atomic-resolution valence electron-energy-loss spectroscopy: Application to graphene

    Science.gov (United States)

    Kapetanakis, Myron D.; Oxley, Mark P.; Zhou, Wu; Pennycook, Stephen J.; Idrobo, Juan-Carlos; Pantelides, Sokrates T.

    2016-10-01

    The detection and identification of impurities and other point defects in materials is a challenging task. Signatures for point defects are typically obtained using spectroscopies without spatial resolution. Here we demonstrate the power of valence electron-energy-loss spectroscopy (VEELS) in an aberration-corrected scanning transmission-electron microscope (STEM) to provide energy-resolved and atomically resolved maps of electronic excitations of individual impurities which, combined with theoretical simulations, yield unique signatures of distinct bonding configurations of impurities. We report VEELS maps for isolated Si impurities in graphene, which are known to exist in two distinct configurations. We also report simulations of the maps, based on density functional theory and dynamical scattering theory, which agree with and provide direct interpretation of observed features. We show that theoretical VEELS maps exhibit distinct and unambiguous signatures for the threefold- and fourfold-coordinated configurations of Si impurities in different energy-loss windows, corresponding to impurity-induced bound states, resonances, and antiresonances. With the advent of new monochromators and detectors with high energy resolution and low signal-to-noise ratio, the present work ushers an atomically resolved STEM-based spectroscopy of individual impurities as an alternative to conventional spectroscopies for probing impurities and defects.

  10. The Influence of Energy Targets and Economic Concerns in Design Strategies for a Residential Nearly-Zero Energy Building

    Directory of Open Access Journals (Sweden)

    Verena Marie Barthelmes

    2014-11-01

    Full Text Available Finding cost-optimal solutions towards nearly-zero energy buildings in accordance with the Energy Performance of Buildings Directive (EPBD is a challenging task. In order to reach the 20-20-20 targets, EU energy policy has introduced new ambitious levels for the large-scale spread of nearly-zero energy buildings (nZEBs and the concept of the cost-optimal level, defined as the energy performance level, which leads to the lowest cost during the estimated economic lifecycle of the building. Consequently, building design has begun a challenge involving both energy targets and economic concerns. The aim of this research is to analyze an example building of a new single family house, using the cost-optimal methodology, in order to define how energy and economic aspects influence the preliminary design phase of the project and, in particular, the choice of the performance features of some components of the project itself, such as envelope elements and systems. The impact on energy performances of different configurations for the building envelope and heating, ventilation and air conditioning (HVAC systems was assessed with the dynamic simulation software EnergyPlus. Finally, the costs of the different design scenarios were estimated, according to the European Standard EN 15459:2007 to establish which of them had the lowest global cost and, consequently, represents the cost-optimal level for the design configurations analyzed. In order to test the stability of the results obtained, different sensitivity analyses were carried out.

  11. Environmental evaluation of the electric and cogenerative configurations for the energy recovery of the Turin municipal solid waste incineration plant.

    Science.gov (United States)

    Panepinto, Deborah; Genon, Giuseppe

    2014-07-01

    Given the desirability of reducing fossil fuel consumption, together with the increasing production of combustible solid wastes, there is clearly a need for waste treatment systems that achieve both volume reduction and energy recovery. Direct incineration method is one such system. The aim of this work was to analyze the municipal solid waste incineration plant currently under construction in the province of Turin (Piedmont, North Italy), especially the potential for energy recovery, and the consequent environmental effects. We analyzed two kinds of energy recovery: electric energy (electrical configuration) only, and both electric and thermal energy (cogenerative configuration), in this case with a different connection hypothesis to the district heating network. After we had evaluated the potential of the incinerator and considered local demographic, energy and urban planning effects, we assumed different possible connections to the district heating network. We computed the local and global environmental balances based on the characteristics of the flue gas emitted from the stack, taking into consideration the emissions avoided by the substituted sources. The global-scale results provided relevant information on the carbon dioxide emissions parameter. The results on the local scale were used as reference values for the implementation of a Gaussian model (Aermod) that allows evaluation of the actual concentration of the pollutants released into the atmosphere. The main results obtained highlight the high energy efficiency of the combined production of heat and electricity, and the opportunity to minimize the environmental impact by including cogeneration in a district heating scheme.

  12. Group divisible designs of four groups and block size five with configuration (1; 1; 1; 2

    Directory of Open Access Journals (Sweden)

    Ronald Mwesigwa

    2016-09-01

    Full Text Available We present constructions and results about GDDs with four groups and block size five in which each block has Configuration $(1, 1, 1, 2$, that is, each block has exactly one point from three of the four groups and two points from the fourth group. We provide the necessary conditions of the existence of a GDD$(n, 4, 5; \\lambda_1, \\lambda_2$ with Configuration $(1, 1, 1, 2$, and show that the necessary conditions are sufficient for a GDD$(n, 4, 5; \\lambda_1,$ $\\lambda_2$ with Configuration $(1, 1, 1, 2$ if $n \

  13. Accurate energy model for WSN node and its optimal design

    Institute of Scientific and Technical Information of China (English)

    Kan Baoqiang; Cai Li; Zhu Hongsong; Xu Yongjun

    2008-01-01

    With the development of CMOS and MEMS technologies, the implementation of a large number of wireless distributed micro-sensors that can be easily and rapidly deployed to form highly redundant, self-configuring, and ad hoc sensor networks. To facilitate ease of deployment, these sensors operate on battery for extended periods of time. A particular challenge in maintaining extended battery lifetime lies in achieving communications with low power. For better understanding of the design tradeoffs of wireless sensor network (WSN), a more accurate energy model for wireless sensor node is proposed, and an optimal design method of energy efficient wireless sensor node is described as well. Different from power models ever shown which assume the power cost of each component in WSN node is constant, the new one takes into account the energy dissipation of circuits in practical physical layer. It shows that there are some parameters, such as data rate, carrier frequency, bandwidth, Tsw, etc, which have a significant effect on the WSN node energy consumption per useful bit (EPUB). For a given quality specification, how energy consumption can be reduced by adjusting one or more of these parameters is shown.

  14. On the configuration of systems of interacting particle with minimum potential energy per particle

    NARCIS (Netherlands)

    Ventevogel, W.J.; Nijboer, B.R.A.

    1979-01-01

    In continuation of previous work we extend the class of two-body potentials, either repulsive or of generalized Lennard-Jones type, for which it can be proved that among all configurations of an infinite one-dimensional system of interacting particles (with fixed density in the case of repulsive int

  15. CONFIGURATION-INTERACTION IN NI METAL AND NI-ALLOYS AND HIGH-ENERGY SPECTROSCOPY

    NARCIS (Netherlands)

    TANAKA, A; JO, T; SAWATZKY, GA

    1992-01-01

    We discuss the electronic state of Ni atoms in Ni metal and of Ni impurity in Cu and Au metals from the viewpoint of 3d configuration interaction (CI) using the Anderson impurity model including atomic multiplets. On the basis of the discussion, we give an interpretation for the Ni 2p-core X-ray pho

  16. Designing A Re-Configurable Fractional Fourier Transform Architecture Using Systolic Array

    Directory of Open Access Journals (Sweden)

    Anal Acharya

    2010-11-01

    Full Text Available FRFT (Fractional Fourier Transforms algorithm, which has been derived from DFT, computes the angular domains within the time and frequency domains. This algorithm is increasingly used in the field of signal filtering, quantum mechanics and optical physics. In this paper we develop an efficient, systolic, re-configurable architecture for a particular type of FRFT called MA-CDFRFT (Multi Angle Centered Discrete FRFT. The benefit of this particular type of FRFT is that it computes all the signal components within equally spaced angles. Systolic architecture is used for this computation as it has certain advantages over the other forms like simplicity, regularity, concurrency and computation intensive The resultant product so developed should meet the challenges of today's market like marketable and cheap along with meeting customer demands. This calls for the architecture to be re-configurable. Re-configurable computer consist of a standard processor and an array of re-configurable hardware. The main processor would control the behavior of the re-configurable hardware. The re-configurable hardware would then be tailored to perform a specific task, such as image processing or pattern matching applications, as if it was built to perform this task exclusively.

  17. Low-energy neutrino factory design

    Directory of Open Access Journals (Sweden)

    C. Ankenbrandt

    2009-07-01

    Full Text Available The design of a low-energy (4 GeV neutrino factory (NF is described, along with its expected performance. The neutrino factory uses a high-energy proton beam to produce charged pions. The π^{±} decay to produce muons (μ^{±}, which are collected, accelerated, and stored in a ring with long straight sections. Muons decaying in the straight sections produce neutrino beams. The scheme is based on previous designs for higher energy neutrino factories, but has an improved bunching and phase rotation system, and new acceleration, storage ring, and detector schemes tailored to the needs of the lower energy facility. Our simulations suggest that the NF scheme we describe can produce neutrino beams generated by ∼1.4×10^{21} μ^{+} per year decaying in a long straight section of the storage ring, and a similar number of μ^{-} decays.

  18. Fluorescence Resonance Energy Transfer Analysis of Recombination Signal Sequence Configuration in the RAG1/2 Synaptic Complex▿ †

    Science.gov (United States)

    Ciubotaru, Mihai; Kriatchko, Aleksei N.; Swanson, Patrick C.; Bright, Frank V.; Schatz, David G.

    2007-01-01

    A critical step in V(D)J recombination is the synapsis of complementary (12/23) recombination signal sequences (RSSs) by the RAG1 and RAG2 proteins to generate the paired complex (PC). Using a facilitated ligation assay and substrates that vary the helical phasing of the RSSs, we provide evidence that one particular geometric configuration of the RSSs is favored in the PC. To investigate this configuration further, we used fluorescent resonance energy transfer (FRET) to detect the synapsis of fluorescently labeled RSS oligonucleotides. FRET requires an appropriate 12/23 RSS pair, a divalent metal ion, and high-mobility-group protein HMGB1 or HMGB2. Energy transfer between the RSSs was detected with all 12/23 RSS end positions of the fluorescent probes but was not detected when probes were placed on the two ends of the same RSS. Energy transfer was confirmed to originate from the PC by using an in-gel FRET assay. The results argue against a unique planar configuration of the RSSs in the PC and are most easily accommodated by models in which synapsed 12- and 23-RSSs are bent and cross one another, with implications for the organization of the RAG proteins and the DNA substrates at the time of cleavage. PMID:17470556

  19. Fluorescence resonance energy transfer analysis of recombination signal sequence configuration in the RAG1/2 synaptic complex.

    Science.gov (United States)

    Ciubotaru, Mihai; Kriatchko, Aleksei N; Swanson, Patrick C; Bright, Frank V; Schatz, David G

    2007-07-01

    A critical step in V(D)J recombination is the synapsis of complementary (12/23) recombination signal sequences (RSSs) by the RAG1 and RAG2 proteins to generate the paired complex (PC). Using a facilitated ligation assay and substrates that vary the helical phasing of the RSSs, we provide evidence that one particular geometric configuration of the RSSs is favored in the PC. To investigate this configuration further, we used fluorescent resonance energy transfer (FRET) to detect the synapsis of fluorescently labeled RSS oligonucleotides. FRET requires an appropriate 12/23 RSS pair, a divalent metal ion, and high-mobility-group protein HMGB1 or HMGB2. Energy transfer between the RSSs was detected with all 12/23 RSS end positions of the fluorescent probes but was not detected when probes were placed on the two ends of the same RSS. Energy transfer was confirmed to originate from the PC by using an in-gel FRET assay. The results argue against a unique planar configuration of the RSSs in the PC and are most easily accommodated by models in which synapsed 12- and 23-RSSs are bent and cross one another, with implications for the organization of the RAG proteins and the DNA substrates at the time of cleavage.

  20. The General Configuration of CEV1 Electric Vehicle's Electrical System and the Design of Its Control Sequence

    Institute of Scientific and Technical Information of China (English)

    2001-01-01

    The general configuration of CEV1 electric vehicle's electrical system and the design scheme of its control sequence are presented, which are modularized by using VMU as master control unit, PMU as power management unit, BMU as battery management unit. It is a rather advanced and practical general design scheme of electric vehicle, because the division of its module function is definite, which is advantage for research, manufacture and maintenance.

  1. On Euclidean designs and the potential energy

    CERN Document Server

    Miezaki, Tsuyoshi

    2011-01-01

    We study Euclidean designs from the viewpoint of the potential energy. For a finite set in Euclidean space, We formulate a linear programming bound for the potential energy by applying harmonic analysis on a sphere. We also introduce the concept of strong Euclidean designs from the viewpoint of the linear programming bound, and we give a Fisher type inequality for strong Euclidean designs. A finite set on Euclidean space is called a Euclidean a-code if any distinct two points in the set are separated at least by a. As a corollary of the linear programming bound, we give a method to determine an upper bound on the cardinalities of Euclidean a-codes on concentric spheres of given radii. Similarly we also give a method to determine a lower bound on the cardinalities of Euclidean t-designs as an analogue of the linear programming bound.

  2. Free energy based melting point prediction by NVT simulation with solid-liquid two-phase configuration

    Science.gov (United States)

    Inagaki, Taichi; Ishida, Toyokazu

    2016-10-01

    We propose a method for computing a melting point on the basis of the Gibbs free energy difference between the solid and liquid phases. The free energy difference is calculated from the average pressure obtained by performing a standard NVT simulation with a solid-liquid two-phase configuration. The method is validated by the melting point calculations of argon and benzene systems. In addition, the method is applied to a mannitol system, and the more reliable melting point than the previous estimate is successfully predicted. These results demonstrate that this method is very simple and useful to calculate melting points.

  3. Regimes of pulsed formation of a compact plasma configuration with a high energy input

    Energy Technology Data Exchange (ETDEWEB)

    Romadanov, I. V.; Ryzhkov, S. V., E-mail: svryzhkov@bmstu.ru [Bauman Moscow State Technical University (Russian Federation)

    2015-10-15

    Results of experiments on the formation of a compact toroidal magnetic configuration at the Compact Toroid Challenge setup are presented. The experiments were primarily aimed at studying particular formation stages. Two series of experiments, with and without an auxiliary capacitor bank, were conducted. The magnetic field was measured, its time evolution and spatial distribution over the chamber volume were determined, and its influence on the formation regimes was investigated.

  4. Nickel-hydrogen battery design for the Transporter Energy Storage Subsystem (TESS)

    Science.gov (United States)

    Lapinski, John R.; Bourland, Deborah S.

    1992-01-01

    Information is given in viewgraph form on nickel hydrogen battery design for the transporter energy storage subsystem (TESS). Information is given on use in the Space Station Freedom, the launch configuration, use in the Mobile Servicing Center, battery design requirements, TESS subassembley design, proof of principle testing of a 6-cell battery, possible downsizing of TESS to support the Mobile Rocket Servicer Base System (MBS) redesign, TESS output capacity, and cell testing.

  5. Sustainable design by embodied energy and demountability

    NARCIS (Netherlands)

    Bosch, M.

    2011-01-01

    This paper is written for the TIDO-course AR0532 Smart & Bioclimatic Design Theory. The construction industry uses vast quantities of materials, resulting in the consumption of energy resources and the release of pollutant emissions to the biosphere. Resource management becomes a key issue in the

  6. Sustainable design by embodied energy and demountability

    NARCIS (Netherlands)

    Bosch, M.

    2011-01-01

    This paper is written for the TIDO-course AR0532 Smart & Bioclimatic Design Theory. The construction industry uses vast quantities of materials, resulting in the consumption of energy resources and the release of pollutant emissions to the biosphere. Resource management becomes a key issue in the d

  7. A method for designing configurations of nested monitoring wells near landfills

    Science.gov (United States)

    Hudak, Paul F.

    A method was devised for designing configurations of monitoring wells, consisting of vertically nested intakes in boreholes. The network-design method involves analyzing a subset of potential contaminant plumes emerging from the downgradient margin of a landfill. Plume widths are evaluated along selected equipotential lines and compared to the lengths of those lines. The method was applied to a 32-ha solid-waste landfill in Tarrant County, Texas, USA. Sixtynine potential source nodes were considered. A 15-borehole network devised by the method registered 93 detections in total, detecting all 69 model-generated plumes by at least one borehole. Based on an enumeration procedure, a minimum of 10 boreholes was needed to detect all of the model-generated plumes. However, the less conservative 10-borehole network had little capability for backup detection. An existing monitoring network of seven downgradient wells detected only 38 model-generated plumes. Results of this study illustrate a practical need for structured approaches to designing detection-based groundwater-monitoring configurations. Résumé Une méthode a été développée pour fournir les caractéristiques de puits de surveillance, avec des points de prélèvements superposés en forage. La méthode de réalisation du réseau s'appuie sur l'analyse d'un ensemble de panaches de pollution potentiels provenant du bord en aval d'une décharge. Les largeurs de panache sont estimées le long d'isopièzes sélectionnées et sont comparées à leur longueur. Cette méthode a été appliquée à une décharge de déchets solides couvrant 32ha, dans le canton de Tarrant (Texas, Etats-Unis). 69 noeuds de source potentielle de pollution ont été pris en compte. Un réseau de 15 forages, défini par la méthode, a enregistré au total 93 alarmes, détectant les 69 panaches simulés dans au moins un forage. Une procédure de dénombrement précise qu'un minimum de 10 forages est nécessaire pour détecter tous les

  8. Aircraft conceptual design study of the canard and threesurface unconventional configurations for the purposes of reducing environmental impacts

    Science.gov (United States)

    Desharnais, Olivier

    With a constant increase in the demand for air transport and today's high fuel price, the aerospace industry is actively searching for new operation methods and technologies to improve efficiency and to reduce the impact it has on the environment. Aircraft manufacturers are exploring many different ways of designing and building better airplanes. One of the considered methods is the use of unconventional aircraft configurations. The objective of this research is to study two configurations, the canard and three-surface, by applying them into a typical high-speed jet aircraft using the conceptual design tools for conventional aircraft available at Bombardier Aerospace (some of them have been modified and validated for the two configurations of interest). This included a weight estimation of the foreplane, an extensive validation of the aerodynamic tool, AVL, and a modification of a physics-based tail-sizing tool. The last tool was found necessary for an accurate foreplane/tailplane sizing, aircraft balancing, establishing the CG envelope and for the assessment of all stability and control requirements. Then, a canard aircraft comparable to the Bombardier research platform aircraft was designed. Final solutions were not obtained from a complete optimization because of some limitations in the design process. The preliminary results show an increase of fuel burn of 10%, leading to an increase of the environmental impacts. The theoretical advantage of not generating any download lift is clearly overwhelmed by the poor effectiveness of the high-lift system. The incapacity to reach a level of high-lift performance close to the one of conventional high-speed aircrafts mostly explains why the canard configuration was found to have no true benefits in this application. Even if no final solution of a three-surface aircraft was obtained in this research, this configuration was identified as being better than the canard case according to the information found in the literature

  9. Power/Energy Estimator for Designing WSN Nodes with Ambient Energy Harvesting Feature

    Directory of Open Access Journals (Sweden)

    Jutel Dominique

    2011-01-01

    Full Text Available Abstract Wireless Sensor Networks (WSNs consist of spatially distributed autonomous sensors to cooperatively monitor physical conditions. Thus, the node battery autonomy is critical. To outperform it, most WSNs rely on the harvesting capability. As nodes can recharge whenever energy is available, the problem is to determine at design time the node autonomy. For our project, we solve it by creating a power/energy estimator that simulates business scenarios to predict node autonomy; the estimation concerns both power and energy features. Based on node architecture configuration, its Dynamic Power Management (DPM policy, and environmental conditions, we present a simulator that helps identify power consumption hot spots and make critical choices during the system design. It also helps to scale the energy storage system as well as the energy harvesters correctly. The hardware part is modelled using the FLPA methodology to develop different node component models with a variable accuracy. For the logical part, we developped a specific DPM by integrating meteorology and weather forecast behaviours. The novelty comes from the ability to simulate the WSN harvesting capability and to estimate at runtime the remaining duration of each service.

  10. Designing a Configurable Services Platform for Mobile Context-Aware Applications

    NARCIS (Netherlands)

    Dockhorn Costa, P.; Ferreira Pires, L.; Sinderen, van M.J.; Yang, L.; Merabti, M.; Ma, J.

    2005-01-01

    Context-aware services platforms aim at supporting the handling of contextual information in order to provide better user-tailored services. This paper proposes a novel services platform architecture to support mobile context-aware applications, giving emphasis to the configurability of the platform

  11. Performance monitoring of different module technologies and design configurations of PV system in South Africa

    CSIR Research Space (South Africa)

    Roro, Kittessa T

    2016-06-01

    Full Text Available Performance monitoring of different module technologies and system configurations of Photovoltaic (PV) systems in South Africa is rare, resulting in-few reports based on field results of PV systems installed and operated in South Africa. The goal...

  12. Design of modular coils for a quasi-axisymmetric stellarator with a flexible control of the magnetic field configuration

    Energy Technology Data Exchange (ETDEWEB)

    Shimizu, A.; Okamura, S.; Isobe, M.; Suzuki, C.; Nishimura, S.; Watari, T.; Matsuoka, K.

    2002-08-01

    A design of the modular coil system for CHS-qa has been made for the plasma configuration '2b32' with the aspect ratio 3.2. The magnetic field strength and the major radius are 1.5 T and 1.5 m, respectively. The normal component of magnetic field produced by the modular coils is minimized on the plasma boundary to obtain the optimum coil design. We put engineering constraint on the distance between adjacent modular coils and the radius of coil curvature. The dependence of the residual normal component of the field on these conditions is examined, and the realistic values for them are selected. Additional coils to control various properties of the magnetic field configuration (the rotational transform, the magnetic well depth, etc.) have been designed and a flexibility of the magnetic field configuration is realized. For the case that the rotational transform crosses the low-order rational value resulting in magnetic islands, the residues of islands are evaluated with which a further improvement of coil design can be made to eliminate magnetic islands. (author)

  13. Spatial Configuration of Energy Consumption and Carbon Emissions of Shanghai, and Our Policy Suggestions

    Directory of Open Access Journals (Sweden)

    Kexi Pan

    2017-01-01

    Full Text Available This research constructs a 1 km × 1 km Shanghai energy consumption and carbon emission spatial grid through a bottom-up approach. First, we locate all energy consumption locations in Shanghai via GIS. Second, we calculate energy consumption and associated CO2 emissions by energy type, by usage type, and by facilities. Finally, we use a spatial grid to represent the energy consumption and CO2 emissions. The grid shows CO2 emissions in Shanghai are highly spatially correlated with energy types and volumes of consumption. This research also finds out that high energy consumption and carbon emission locations in Shanghai display significant spatial aggregation. In 7209 spatial energy consumption cells, the top 10 grids of emissions account for 52.8% of total CO2 emissions in Shanghai; the top 20 grids account for 64.5% and the top 50 grids account for 76.5%. The most critical point emission sources are coal-fired power plants and iron and steel plants. The most important line emission sources are the Yan’an Road and Inner Ring viaducts. The area emission sources that account for the most future-projected growth are commercial and residential natural gas. After this spatial analysis, this paper makes policy suggestions and solutions to conserve energy consumption and mitigate carbon emissions in Shanghai.

  14. Reynolds stress flow shear and turbulent energy transfer in reversed field pinch configuration

    Science.gov (United States)

    Vianello, Nicola; Spolaore, Monica; Serianni, Gianluigi; Regnoli, Giorgio; Spada, Emanuele; Antoni, Vanni; Bergsåker, Henric; Drake, James R.

    2003-10-01

    The role of Reynolds Stress tensor on flow generation in turbulent fluids and plasmas is still an open question and the comprehension of its behavior may assist the understanding of improved confinement scenario. It is generally believed that shear flow generation may occur by an interaction of the turbulent Reynolds stress with the shear flow. It is also generally believed that this mechanism may influence the generation of zonal flow shears. The evaluation of the complete Reynolds Stress tensor requires contemporary measurements of its electrostatic and magnetic part: this requirement is more restrictive for Reversed Field Pinch configuration where magnetic fluctuations are larger than in tokamak . A new diagnostic system which combines electrostatic and magnetic probes has been installed in the edge region of Extrap-T2R reversed field pinch. With this new probe the Reynolds stress tensor has been deduced and its radial profile has been reconstructed on a shot to shot basis exploring differen plasma conditions. These profiles have been compared with the naturally occurring velocity flow profile, in particular during Pulsed Poloidal Current Drive experiment, where a strong variation of ExB flow radial profile has been registered. The study of the temporal evolution of Reynolds stress reveals the appearance of strong localized bursts: these are considered in relation with global MHD relaxation phenomena, which naturally occur in the core of an RFP plasma sustaining its configuration.

  15. Integrated energy design of the building envelope

    Energy Technology Data Exchange (ETDEWEB)

    Vraa Nielsen, M.

    2012-07-01

    This thesis describes the outcome of the PhD project Integrated energy design of the building envelope carried out through a combination of scientific dissemination reported through peer-reviewed journals and a wide range of affiliated projects involved in at an architectural firm. The research project analysed how the implementation of technical knowledge early in the building design process can quantify the effect of a building's facades on its energy efficiency and indoor climate and thereby facilitate a more qualified design development. The project was structured in the following way: 1) the importance of integrating knowledge in the early stages of design, and how it can be done; 2) understanding the facade's typology; and 3) the complex notion of comfort. The project touched not only on the technical capabilities and requirements governing facade design, but also the process by which it takes place. This was done by applying the methodology of Integrated Energy Design (IED) and analysing its applicability in the design of facades. A major part of the project was an actual engagement in the architectural process to test out incorporating a consciousness about energy and comfort as part of a more holistic performance evaluation. The research project illustrates the great potential in taking passive properties into account through a geometrical optimisation inherent in the development of the architectural concept. It demonstrates that integration of technical knowledge at the early stages of design not only can qualify the geometrical processing, but also facilitate the design development of the facade. Thereby a more holistic performance optimisation can be obtained through parameters such as overall facade geometry and orientation, functional organisation, room height and depth, facade layout, window geometry and transparency, design of the window aperture, etc. Through the wide range of affiliated project involved in at the architectural firm over

  16. Biomechanical Energy Harvester Design For Active Prostheses

    Directory of Open Access Journals (Sweden)

    Akın Oğuz Kaptı

    2012-06-01

    Full Text Available One of the factors restricting the functions of active prostheses is limited charge times and weights of the batteries. Therefore, some biomechanical energy harvesting studies are conducted for reducing the dependence on batteries and developing the systems that produce energy by utilizing one's own actions during daily living activities. In this study, as a new approach to meet energy needs of active-controlled lower limb prostheses, the design of a biomechanical energy harvester that produces electrical energy from the movements of the knee joint during gait were carried out. This harvester is composed of the generator, planetary gear system and one-way clutch that transmit just the knee extension. Low weight, low additional metabolic power consumption requirement and high electrical power generation are targeted in design process. The total reduction ratio of the transmission is 104, and the knee joint reaction torque applied by the system is 6 Nm. Average electrical powers that can be obtained are 17 W and 5,8 W for the swing extension phase and the entire cycle, respectively. These values seem to be sufficient for charging the battery units of many prostheses and similar medical systems, and portable electronic devices such as mobile phones, navigation devices and laptops.

  17. Implementation of a design and configuration management platform for fusion components on the Tore Supra WEST Project

    Energy Technology Data Exchange (ETDEWEB)

    Benoît, Fabrice, E-mail: fabrice-2.benoit@cea.fr [CEA, IRFM, F-13108 Saint-Paul-lez-Durance (France); Allegretti, Ludovic [CEA, IRFM, F-13108 Saint-Paul-lez-Durance (France); Aumeunier, Marie-Hélène [OPTIS, ZE de La Farlède, F-83078 Toulon Cedex 9 (France); Bucalossi, Jérôme; Doceul, Louis; Faïsse, Frederic; Firdaouss, Medhi; Geynet, Michel; Houtte, Didier van; Larroque, Sébastien; Magaud, Philippe; Maini, Patrick; Missirlian, Marc; Parrat, Hélène [CEA, IRFM, F-13108 Saint-Paul-lez-Durance (France); Robert, Julien [SOFYNE, F-69800 Saint Priest (France)

    2014-10-15

    Highlights: •A design and configuration management platform is under development for managing fusion components lifecycle at CEA. •Design platform ensures an efficient sharing of the data and provides connections between the different software and databases involved in fusion components design. •Design platform rollout on WEST project is ongoing as part of change control and configuration management implementation. -- Abstract: This paper presents the technical solutions and methodologies that are used and under development for managing the design lifecycle of the WEST project (W – for tungsten – Environment in Steady-state Tokamak, upgrade of Tore Supra's with actively cooled tungsten plasma facing components) fusion components and explains the interfaces that are implemented or in construction to connect together the different tools like documents management system, CAD modeler, or simulation codes around the data management backbone. It describes the methodologies used on the WEST project to optimize the design process by managing the engineering data workflow and ensuring the consistency between the different 3D representations for design or analysis as well as the specification or interfaces documents. Finally it explains how this platform contributes to reach the project targets in terms of performance, cost and schedule.

  18. Evaluation of piezoelectret foam in a multilayer stack configuration for low-level vibration energy harvesting applications

    Science.gov (United States)

    Ray, Chase A.; Anton, Steven R.

    2015-04-01

    Electronic devices are high demand commodities in today's world, and such devices will continue increasing in popularity. Currently, batteries are implemented to provide power to these devices; however, the need for battery replacement, their cost, and the waste associated with battery disposal present a need for advances in self-powered technology. Energy harvesting technology has great potential to alleviate the drawbacks of batteries. In this work, a novel piezoelectret foam material is investigated for low-level energy harvesting. Specifically, piezoelectret foam assembled in a multilayer stack configuration is explored. Modeling and experimentation of the stack behavior when excited in compression at low frequencies are performed to investigate piezoelectret foam as a multilayer energy harvester. An examination of modeling piezoelectret foam as a stack with an equivalent circuit is made following recently published work and is used in this study. A 20-layer prototype device is fabricated and experimentally tested via harmonic base excitation. Electromechanical testing is performed by compressing the foam stack to obtain output electrical energy; consequently, allowing the frequency response between input mechanical energy and output electrical energy to be developed. Modeling results are compared to the experimental measurements to assess the fidelity of the model. Lastly, energy harvesting experimentation in which the device is subject to harmonic base excitation at the natural frequency is conducted to determine the ability of the piezoelectret foam stack to successfully charge a capacitor.

  19. Profiling transition-state configurations on the Trypanosoma cruzi trans-sialidase free-energy reaction surfaces.

    Science.gov (United States)

    Rogers, Ian L; Naidoo, Kevin J

    2015-01-22

    Enzymatically catalyzed reactions pass from reactants to products via transition states that are short-lived and potentially characterized from free-energy reaction surfaces. We compute the reaction surface for Trypanosoma cruzi trans-sialidase using the Free Energy from Adaptive Reaction Coordinate Forces method. The reaction coordinates are the bonds between the sialic acid and the leaving group (TYR342) and the sialic acid and the nucpleophile (ASP59). We are able to track progress of the reaction trajectories up to (incomplete), about (recrossed), and across (crossed) the col that divides the reactant (covalent intermediate) and product (Michaelis complex) surfaces. More than 40 transition state configurations were isolated from these trajectories, and the sialic acid substrate conformations were analyzed as well as the substrate interactions with the nucleophile and catalytic acid/base. A successful barrier crossing requires that the substrate passes through a family of E5, (4)H5, and (6)H5 pucker conformations. These puckers interact slightly differently with the enzyme. The E5 and (4)H5 conformations have a high-frequency hydrogen bonding with Asp96, while (6)H5 puckers show increased hydrogen bonding between sialic acid O-8-Glu230. Our analysis of Trypanosoma cruzi trans-sialidase configurations that populate the col separating the reactant from product surfaces brings new evidence to the prevailing premise that there are several pathways from reactant to product passing through the saddle and successful product formation is not restricted to the minimum energy path and transition state.

  20. Design + energy: results of a national student design competition

    Energy Technology Data Exchange (ETDEWEB)

    1980-01-01

    A national competition for students in schools of architecture was conducted during the Spring of 1980. The competition was the first of a series of competitions that emphasized the integration of architectural design and energy considerations in medium-scale building projects, and specifically applying passive solar design strategies and the appropriate use of brick masonry materials. Some 300 faculty members and over 2200 students representing 80 of the 92 US architecture schools participated in the program. A summary is presented of the program and the range of submissions grouped by problem types and general climatic region.

  1. Wind energy systems control engineering design

    CERN Document Server

    Garcia-Sanz, Mario

    2012-01-01

    IntroductionBroad Context and MotivationConcurrent Engineering: A Road Map for EnergyQuantitative Robust ControlNovel CAD Toolbox for QFT Controller DesignOutline Part I: Advanced Robust Control Techniques: QFT and Nonlinear SwitchingIntroduction to QFTQuantitative Feedback TheoryWhy Feedback? QFT OverviewInsight into the QFT TechniqueBenefits of QFTMISO Analog QFT Control SystemIntroductionQFT Method (Single-Loop MISO System)Design Procedure OutlineMinimum-Phase System Performance SpecificationsJ LTI Plant ModelsPlant Templates of P?(s), P( j_i )Nominal PlantU-Contour (Stability Bound)Trackin

  2. Design of an Oximeter Based on LED-LED Configuration and FPGA Technology

    Directory of Open Access Journals (Sweden)

    Radovan Stojanovic

    2013-01-01

    Full Text Available A fully digital photoplethysmographic (PPG sensor and actuator has been developed. The sensing circuit uses one Light Emitting Diode (LED for emitting light into human tissue and one LED for detecting the reflectance light from human tissue. A Field Programmable Gate Array (FPGA is used to control the LEDs and determine the PPG and Blood Oxygen Saturation (SpO2. The configurations with two LEDs and four LEDs are developed for measuring PPG signal and Blood Oxygen Saturation (SpO2. N-LEDs configuration is proposed for multichannel SpO2 measurements. The approach resulted in better spectral sensitivity, increased and adjustable resolution, reduced noise, small size, low cost and low power consumption.

  3. Synthesis, design and operation optimization of a marine energy system

    Energy Technology Data Exchange (ETDEWEB)

    Dimopoulos, George G.; Kougioufas, Aristotelis V.; Frangopoulos, Christos A. [National Technical University of Athens, School of Naval Architecture and Marine Engineering, Heroon Polytechniou 9, 157 73 Zografou (Greece)

    2008-02-15

    Recent developments in the global fuel markets imposed the need of increased fuel economy and cost effectiveness of sea-going vessels. Optimization of the ship's total energy system, as a whole, is now a demand of the marine industry sector in order to address the significant increase of installation and operational costs. This study is focused on the synthesis, design and operation optimization of a marine energy system. A realistic example of a cruise liner energy system has been selected. Basic technology options have been identified and a generic energy system model has been constructed. Various configuration options, types of technologies and existence of components have been incorporated in the generic system. In addition, time varying operational requirements for this cruise liner ship have been considered, resulting in a time dependent operation optimization problem. The complete optimization problem has been solved using a novel algorithm, inspired by evolutionary and social behavior metaphors. A parametric analysis with respect to the fuel price demonstrated changes in the optimum synthesis of the system. (author)

  4. Low-stress mounting configuration design for large aperture laser transport mirror

    Science.gov (United States)

    Zhang, Zheng; Quan, Xusong; Yao, Chao; Wang, Hui

    2016-10-01

    TM1-6S1 large aperture laser transport mirror is a crucial optical unit of high power solid-state laser in the Inertial Confinement Fusion (ICF) facility. This article focuses on the low-stress and precise mounting method of large-aperture mirror. Based on the engineering practice of SG-III, the state-of-the-art and key problems of current mounting configuration are clarified firstly. Subsequently, a brand new low-stress mounting configuration with flexure supports is proposed. Opto-mechanical model of the mirror under mounting force is built up with elastic mechanics theory. Further, numerical methods and field tests are employed to verify the favorable load uniform capacity and load adjust capacity of flexure supports. With FEM, the relation between the mounting force from new configuration and the mirror surface distortion (wavefront error) is clarified. The novel mounting method of large aperture optics could be not only used on this laser transport mirror, but also on the other transmission optics and large crystals in ICF facilities.

  5. On Design for Electrochemical Energy Storage Materials

    OpenAIRE

    Sakaushi, Ken

    2014-01-01

    In this dissertation, diverse strategic designs of energy storage materials were explored. The main aims were: affordability and high-performances. I) on eco-efficient synthesis of 1D intercalation compounds was described; a low-temperature aqueous solution synthesis of nanostructured 1D (molybdenum trioxide) MoO3 was developed. Subsequent self-assembly of the fibers to form large-scale freestanding films in paper-like structure was achieved without any assistance of organic compounds. I...

  6. Direct acceleration of ions to low and medium energies by a crossed-laser-beam configuration

    Directory of Open Access Journals (Sweden)

    Yousef I. Salamin

    2011-07-01

    Full Text Available Calculations show that 10 keV helium and carbon ions, injected midway between two identical 1 TW-power crossed laser beams of radial polarization, can be accelerated in vacuum to energies of utility in ion lithography. As examples, identical laser beams, crossed at 10° and focused to waist radii of 7.42  μm, accelerate He^{2+} and C^{6+} ions to average kinetic energies near 75 and 165 keV over distances averaging less than 7 and 6 mm, respectively. The spread in kinetic energy in both cases is less than 1% and the particle average angular deflection is less than 7 mrad. More energy-demanding industrial applications require higher-power laser beams for their direct ion laser acceleration.

  7. Field Evaluation of Four Novel Roof Designs for Energy-Efficient Manufactured Homes

    Energy Technology Data Exchange (ETDEWEB)

    Levy, E. [Levy Partnership Inc., New York, NY (United States); Dentz, J. [Levy Partnership Inc., New York, NY (United States); Ansanelli, E. [Levy Partnership Inc., New York, NY (United States); Barker, G. [Levy Partnership Inc., New York, NY (United States); Rath, P. [Levy Partnership Inc., New York, NY (United States); Dadia, D. [Levy Partnership Inc., New York, NY (United States)

    2015-12-01

    A five-bay roof test structure was built, instrumented and monitored in an effort to determine through field testing and analysis the relative contributions of select technologies toward reducing energy use in new manufactured homes. The roof structure in Jamestown, California was designed to examine how differences in roof construction impact space conditioning loads, wood moisture content and attic humidity levels. Conclusions are drawn from the data on the relative energy and moisture performance of various configurations of vented and sealed attics.

  8. Nanoscale piezoelectric vibration energy harvester design

    Directory of Open Access Journals (Sweden)

    Hamid Reza Foruzande

    2017-09-01

    Full Text Available Development of new nanoscale devices has increased the demand for new types of small-scale energy resources such as ambient vibrations energy harvesters. Among the vibration energy harvesters, piezoelectric energy harvesters (PEHs can be easily miniaturized and fabricated in micro and nano scales. This change in the dimensions of a PEH leads to a change in its governing equations of motion, and consequently, the predicted harvested energy comparing to a macroscale PEH. In this research, effects of small scale dimensions on the nonlinear vibration and harvested voltage of a nanoscale PEH is studied. The PEH is modeled as a cantilever piezoelectric bimorph nanobeam with a tip mass, using the Euler-Bernoulli beam theory in conjunction with Hamilton’s principle. A harmonic base excitation is applied as a model of the ambient vibrations. The nonlocal elasticity theory is used to consider the size effects in the developed model. The derived equations of motion are discretized using the assumed-modes method and solved using the method of multiple scales. Sensitivity analysis for the effect of different parameters of the system in addition to size effects is conducted. The results show the significance of nonlocal elasticity theory in the prediction of system dynamic nonlinear behavior. It is also observed that neglecting the size effects results in lower estimates of the PEH vibration amplitudes. The results pave the way for designing new nanoscale sensors in addition to PEHs.

  9. Guide for Operational Configuration Management Program including the adjunct programs of design reconstitution and material condition and aging management. Part 2

    Energy Technology Data Exchange (ETDEWEB)

    1993-11-01

    This standard presents program criteria and implementation guidance for an operational configuration management program for DOE nuclear and non-nuclear facilities. This Part 2 includes chapters on implementation guidance for operational configuration management, implementation guidance for design reconstitution, and implementation guidance for material condition and aging management. Appendices are included on design control, examples of design information, conduct of walkdowns, and content of design information summaries.

  10. Research of configuration design for sewing machine%平缝机的组态设计方法研究

    Institute of Scientific and Technical Information of China (English)

    张莉

    2011-01-01

    To improve design efficiency and quality of sewing machine products, configuration product design method was proposed. Product development process based on configuration technology was presented, and componentization design method was analyzed. On the base of analytic hierarchy process and fuzzy comprehensive evaluation, component determination process was described. Then component was design by generation rules and modification rules. Finally, the application in the design of sewing machine shows the feasibility and validity of proposed method.%为了提高平缝机产品的设计效率和质量,提出了一种组态式产品设计方法,并给出了基于组态技术的产品开发流程,分析了组件化设计的方法.在应用层次分析法和模糊综合评判算法的基础上,对组件的确定过程进行了详细阐述,并通过生成性规则和修改性规则两种准则来完成组件的设计.最后,应用该组态设计方法对平缝机进行产品设计开发,验证了该方法的可行性和有效性.

  11. Out-of-equilibrium energy flow and steady state configurations in AdS/CFT

    CERN Document Server

    Megias, Eugenio

    2015-01-01

    We study out-of-equilibrium energy flow in a strongly coupled system by using the AdS/CFT correspondence. In particular, we describe the appearance of a steady state connecting two asymptotic equilibrium systems. We obtain results within the linear response regime.

  12. Optimization of PV-based energy production by dynamic PV-panel/inverter configuration

    DEFF Research Database (Denmark)

    Paasch, Kasper; Nymand, Morten; Haase, Frerk

    This paper investigates the possible increase in annual energy production of a PV system with more than one MPPT (maximum power point tracker) input channels under Nordic illumination conditions, in case a concept of dynamic switching of the PV panels is used at the inputs of the inverters....

  13. Evaluation of the environmental sustainability of different waste-to-energy plant configurations.

    Science.gov (United States)

    Lombardi, Lidia; Carnevale, Ennio A

    2017-07-17

    Residual municipal solid waste (MSW) has an average lower heating value higher than 10GJ/Mg in the EU, and can be recovered in modern Waste-to-Energy (WtE) plants, producing combined heat and power (CHP) and reaching high levels of energy recovery. CHP is pinpointed as the best technique for energy recovery from waste. However, in some cases, heat recovery is not technically feasible - due to the absence of a thermal user (industrial plant or district heating) in the vicinity of the WtE plant - and power production remains the sole possibility. In these cases, there are some challenges involved in increasing the energy performance as much as possible. High energy recovery efficiency values are very important for the environmental sustainability of WtE plants. The more electricity and heat is produced, the better the saving of natural resources that can be achieved. Within this frame, the aim of this work is to carry out an environmental assessment, through Life Cycle Assessment, of an MSW WtE plant, considering different sizes and operated in different ways, from power production only to full cogeneration. The main assumption is that the electric conversion efficiency increases as the plant size increases, introducing technical improvements thanks to the economies of scale. Impact assessment results were calculated using ReCiPe 2008 methods. The climate change indicator is positive when the WtE plant is operated in power production only mode, with values decreasing for the increasing size. Values for the climate change are negative when cogeneration is applied, requiring increasing cogeneration ratios for decreasing size. Similarly, the fossil fuel depletion indicator benefits from increase of both the plant size and the cogeneration rate, but it is always negative, meaning that the residual MSW burning with energy recovery always provides a saving of fossil primary energy. Other indicator values are in general negative and are also beneficially affected by

  14. Configuration Mixing within the Energy Density Functional Formalism: Removing Spurious Contributions from Non-Diagonal Energy Kernels

    CERN Document Server

    Lacroix, D; Bender, M

    2008-01-01

    Multi-reference calculations along the lines of the Generator Coordinate Method or the restoration of broken symmetries within the nuclear Energy Density Functional (EDF) framework are becoming a standard tool in nuclear structure physics. These calculations rely on the extension of a single-reference energy functional, of the Gogny or the Skyrme types, to non-diagonal energy kernels. There is no rigorous constructive framework for this extension so far. The commonly accepted way proceeds by formal analogy with the expressions obtained when applying the generalized Wick theorem to the non-diagonal matrix element of a Hamilton operator between two product states. It is pointed out that this procedure is ill-defined when extended to EDF calculations as the generalized Wick theorem is taken outside of its range of applicability. In particular, such a procedure is responsible for the appearance of spurious divergences and steps in multi-reference EDF energies, as was recently observed in calculations restoring pa...

  15. Design of a full-dynamic-range balanced detection heterodyne gyroscope with common-path configuration.

    Science.gov (United States)

    Lin, Chu-En; Yu, Chih-Jen; Chen, Chii-Chang

    2013-04-22

    In this article, we propose an optical heterodyne common-path gyroscope which has common-path configuration and full-dynamic range. Different from traditional non-common-path optical heterodyne technique such as Mach-Zehnder or Michelson interferometers, we use a two-frequency laser light source (TFLS) which can generate two orthogonally polarized light with a beat frequency has a common-path configuration. By use of phase measurement, this optical heterodyne gyroscope not only has the capability to overcome the drawback of the traditional interferometric fiber optic gyro: lack for full-dynamic range, but also eliminate the total polarization rotation caused by SMFs. Moreover, we also demonstrate the potential of miniaturizing this gyroscope as a chip device. Theoretically, if we assume that the wavelength of the laser light is 1550nm, the SMFs are 250m in length, and the radius of the fiber ring is 3.5cm, the bias stability is 0.872 deg/hr.

  16. Groundwater Energy Designer (GED); Groundwater Energy Designer (GED). Computergestuetztes Auslegungstool zur Waerme- und Kaeltenutzung von Grundwasser

    Energy Technology Data Exchange (ETDEWEB)

    Poppei, J.; Mayer, G.; Schwarz, R.

    2006-07-01

    This final report for the Swiss Federal Office of Energy (SFOE) takes a look at a computer-aided dimensioning tool (Groundwater Energy Designer, GED) for use in the calculation work involved in designing systems for the thermal use of groundwater. The interactive tool is designed to support those involved in the analysis of heating and cooling demands and the direct use of groundwater to help meet such needs. The program and its user interface in German and French are described in detail, as are the basic models and data used in the calculations. Simulation aspects and the verification of the software are also discussed. Results of tests made are presented and discussed.

  17. Energy and Exergy Analysis for Improving the Energy Performance of Air-Cooled Liquid Chillers by Different Condensing-Coil Configurations

    Directory of Open Access Journals (Sweden)

    Tzong-Shing Lee

    2012-03-01

    Full Text Available This study constructed a parameter analysis for improving the energy performance of air-cooled water chillers by altering the angle configuration of the condenser coils. The mathematical models for energy and exergy analyses of the individual components and overall system of air-cooled water chillers are presented. This study investigated the potential enhancement of performance efficiency in air-cooled chillers and the energy conversion efficiency of each component, in order to determine how the angle configuration of condenser coils influences chiller performance. This study found that the overall performance of an air-cooled chiller could be improved by approximately 3.4%, and the total irreversibility could be reduced by approximately 2.7%. With each 1% increase in average wind speed over the condenser coils, the overall performance of an air‑cooled chiller was found to be enhanced by approximately 0.43%, and its total irreversibility was reduced by approximately 0.35%. The results of this study can be effectively applied to air-cooled condenser units, and can provide an important basis of reference for developing and enhancing the energy efficiency of air-cooled chillers.

  18. The Resource Configuration Method with Lower Energy Consumption Based on Prediction in Cloud Data Center

    Directory of Open Access Journals (Sweden)

    Quan Liang

    2014-07-01

    Full Text Available The cloud computing data center have numerous hosts as well as application requests. In future, the short response time and user Qos are required, and the lower electricity power consumption to build the low-carbon green network is an irrevocable trend. The paper first puts forward a reconfiguration framework based on the request prediction of Double Exponential Smoothing, On the basis, work out in advance the allocation scheme which can improve the resource utilization ratio as well as lower energy consumption. The paper also present a concept of Utility Ratio Matrix (URM to represent allocations of hosts and Virtual Machines (VMs and a reconfiguration algorithm. The algorithm can separate the reconfiguration computing from the real allocation so that it can avoid a time delay, and can also reduce the energy consumption in data center. The corresponding analysis and experimental results show the feasibility of the reconfiguration algorithm in this paper.

  19. A Multi-objective Optimization of Broadband WMN: Energy-Capacity Tradeoff and Optimal System Configuration

    OpenAIRE

    Ouni, Anis; Rivano, Hervé; Valois, Fabrice

    2011-01-01

    This paper is focused on broadband wireless mesh networks based on OFDMA resource management. We develop an extensible linear programing model using column generation to compute power efficient schedules with high network capacity. We adopt a more realistic model for the physical layer using SINR model with a fine tuned power control at each node. Correlation between capacity and energy consumption is analyzed as well as the impact of physical layer parameters - SINR threshold and path-loss e...

  20. Structural Design Exploration of an Electric Powered Multi-Propulsor Wing Configuration

    Science.gov (United States)

    Moore, James B.; Cutright, Steve

    2017-01-01

    Advancements in aircraft electric propulsion may enable an expanded operational envelope for electrically powered vehicles compared to their internal combustion engine counterparts. High aspect ratio wings provide additional lift and drag reduction for a proposed multi-propulsor design, however, the challenge is to reduce the weight of wing structures while maintaining adequate structural and aeroelastic margins. Design exploration using a conventional design-and-build philosophy coupled with a finite element method (FEM)-based design of experiments (DOE) strategy are presented to examine high aspect ratio wing structures that have spanwise distributed electric motors. Multiple leading-edge-mounted engine masses presented a challenge to design a wing within acceptable limits for dynamic and aeroelastic stability. Because the first four primary bending eigenmodes of the proposed wing structure are very sensitive to outboard motor placement, safety-of-flight requirements drove the need for multiple spars, rib attachments, and outboard structural reinforcements in the design. Global aeroelasticity became an increasingly important design constraint during the on-going design process, with outboard motor pod flutter ultimately becoming a primary design constraint. Designers successively generated models to examine stress, dynamics, and aeroelasticity concurrently. This research specifically addressed satisfying multi-disciplinary design criteria to generate fluid-structure interaction solution sets, and produced high aspect ratio primary structure designs for the NASA Scalable Convergent Electric Propulsion Technology and Operations Research (SCEPTOR) project in the Aeronautic Research Mission Directorate at NASA. In this paper, a dynamics-driven, quasi-inverse design methodology is presented to address aerodynamic performance goals and structural challenges encountered for the SCEPTOR demonstrator vehicle. These results are compared with a traditional computer aided

  1. Photovoltaic energy systems: Design and installation

    Science.gov (United States)

    Buresch, M.

    The characteristics of solar radiation, the design of solar cells, and the installation of Si solar cell arrays for various applications are described. The discussion is limited to medium-scale photovoltaic systems, from 0.1-100 kW peak output, mounted in fixed flat plate modules, the simplest, most maintenance-free concept. Solar cell functioning principles are outlined, including the parasitic mechanisms which reduce cell efficiency. The magnitude, variations, and distribution of the global solar energy input are quantified. Consideration is given to series and parallel connected solar arrays, and to performance under a variable load. Array protection and failure detection are explored, as are integrated array power conditioning equipment comprising energy storage, voltage regulation, and ac to dc converters. Attention is also devoted to array mounting and matching solar cell systems to load.

  2. Energy Conscious Design: Educational Facilities. [Brief No.] 1.

    Science.gov (United States)

    American Inst. of Architects, Washington, DC.

    An energy task group of the American Institute of Architects discusses design features and options that educational facility designers can use to create an energy efficient school building. Design elements cover the building envelope, energy storage system, hydronic heating/cooling systems, solar energy collection, building orientation and shape,…

  3. Real-time debugger with bitstream configurator and C language design control for FPGAs

    Science.gov (United States)

    Casselman, Steve; Schewel, John; Wartel, Frank

    2001-07-01

    At the boundary between hardware and software, where FPGAs with 2,000,000 gates is just the beginning, we've found that the tools you have in your toolbox make all the difference. With larger and more feature rich programmable devices such as the VirtexTM Platform FPGA, even minors changes in the design can require hours of compile time. The combination of design complexity and component size is taxing current design entry and implementation tools, making the design cycle loner. The simulation-verification cycle doesn't mean the design will work in the final product. The engineer needs more than ever, to debug designs within the target hardware in real-time. We have built a series of integrated tools aimed at enhancing productivity at the last stages of product design, the final ten percent of the design that takes ninety percent of the time. The tools shown are not meant to replace current tools. These are advanced tools for the FPGA power user. Our goal is creating a set of tools specifically designed to provide better design control, dramatically reduce iteration times and enable real-time In-Circuit debugged in hardware. We have organized this series of tools as The Technology StackTM.

  4. Special ESP configurations designed to test and produce Yemen oil field. [Electric-Submersible Pump

    Energy Technology Data Exchange (ETDEWEB)

    Wilkie, D.I. (Canadian Occidental Petroleum Ltd., Calgary, Alberta (Canada))

    1993-09-27

    Innovative electric-submersible-pump (ESP) configurations were used in the exploration phase of a Yemen oil field discovered by Canadian Occidental Petroleum Ltd. Because of subnormal reservoir pressure, CanOxy developed the field with ESPs and had to install surface components that could operate at the high, 130 F., ambient temperatures common in Yemen. The field is in a remote area that has seen very little development. The reservoirs produce a medium-to-heavy crude with a low gas/oil ratio, typically less than 20 scf/bbl. Problems faced in evaluating the field included drilling through unconsolidated sands with high flow capacity and subnormal reservoir pressure. CanOxy had to develop the technology to test the wells during the exploration phase, and intends to use new, or at least uncommon technology, for producing the wells. The paper describes testing the wells, the electric generators and variable speed drives, and the use of these pumps on production wells.

  5. Configuring simulation models using CAD techniques : a new approach to warehouse design

    OpenAIRE

    Brito, António Ernesto da Silva Carvalho

    2013-01-01

    The research reported in this thesis is related to the development and use of software tools for supporting warehouse design and management. Computer Aided Design and Simulation techniques are used to develop a software system that forms the basis of a Decision Support System for warehouse design. The current position of simulation software is reviewed. It is investigated how appropriate current simulation software is for warehouse modelling. Special attention is given to Vi...

  6. RotCFD: A Viscous Design Tool for Advanced Configurations Project

    Data.gov (United States)

    National Aeronautics and Space Administration — During initial design studies, parametric variation of vehicle geometry is routine. In addition, rotorcraft engineers traditionally use the wind tunnel to evaluate...

  7. Rational Design of Molecular Hole-Transporting Materials for Perovskite Solar Cells: Direct versus Inverted Device Configurations.

    Science.gov (United States)

    Grisorio, Roberto; Iacobellis, Rosabianca; Listorti, Andrea; De Marco, Luisa; Cipolla, Maria Pia; Manca, Michele; Rizzo, Aurora; Abate, Antonio; Gigli, Giuseppe; Suranna, Gian Paolo

    2017-07-26

    Due to a still limited understanding of the reasons making 2,2',7,7'-tetrakis(N,N-di-p-methoxyphenylamine)-9,9'-spirobifluorene (Spiro-OMeTAD) the state-of-the-art hole-transporting material (HTM) for emerging photovoltaic applications, the molecular tailoring of organic components for perovskite solar cells (PSCs) lacks in solid design criteria. Charge delocalization in radical cationic states can undoubtedly be considered as one of the essential prerequisites for an HTM, but this aspect has been investigated to a relatively minor extent. In marked contrast with the 3-D structure of Spiro-OMeTAD, truxene-based HTMs Trux1 and Trux2 have been employed for the first time in PSCs fabricated with a direct (n-i-p) or inverted (p-i-n) architecture, exhibiting a peculiar behavior with respect to the referential HTM. Notwithstanding the efficient hole extraction from the perovskite layer exhibited by Trux1 and Trux2 in direct configuration devices, their photovoltaic performances were detrimentally affected by their poor hole transport. Conversely, an outstanding improvement of the photovoltaic performances in dopant-free inverted configuration devices compared to Spiro-OMeTAD was recorded, ascribable to the use of thinner HTM layers. The rationalization of the photovoltaic performances exhibited by different configuration devices discussed in this paper can provide new and unexpected prospects for engineering the interface between the active layer of perovskite-based solar cells and the hole transporters.

  8. 1995 NASA High-Speed Research Program Sonic Boom Workshop. Volume 2; Configuration Design, Analysis, and Testing

    Science.gov (United States)

    Baize, Daniel G. (Editor)

    1999-01-01

    The High-Speed Research Program and NASA Langley Research Center sponsored the NASA High-Speed Research Program Sonic Boom Workshop on September 12-13, 1995. The workshop was designed to bring together NASAs scientists and engineers and their counterparts in industry, other Government agencies, and academia working together in the sonic boom element of NASAs High-Speed Research Program. Specific objectives of this workshop were to: (1) report the progress and status of research in sonic boom propagation, acceptability, and design; (2) promote and disseminate this technology within the appropriate technical communities; (3) help promote synergy among the scientists working in the Program; and (4) identify technology pacing, the development C, of viable reduced-boom High-Speed Civil Transport concepts. The Workshop was organized in four sessions: Sessions 1 Sonic Boom Propagation (Theoretical); Session 2 Sonic Boom Propagation (Experimental); Session 3 Acceptability Studies-Human and Animal; and Session 4 - Configuration Design, Analysis, and Testing.

  9. The difference of energies of Si atoms with single-crystalline, amorphous, free and nanoparticle configurations

    Science.gov (United States)

    Wang, Y. L.; Deng, Z. C.; Chu, L. Z.; Fu, G. S.; Peng, Y. C.

    2009-04-01

    Nanocrystalline silicon (nc-Si) films were systematically prepared via three ways: a) laser anneal or b) thermal anneal of the amorphous silicon (α-Si) films deposited by pulsed-laser ablation (PLA) in base vacuum, c) direct PLA in high-purity Ar gas with pressure of 10 Pa. The anneal-laser fluence, thermal-anneal temperature and ablation-laser fluence thresholds corresponding to the beginning of nanoparticles formation were respectively determined by using scanning electron microscopy (SEM), Raman and X-ray diffraction (XRD) techniques. Incorporated with crystallization mechanism, energies compensated for the formation of one Si nanoparticle in the three ways were calculated approximately. The result shows that for different crystallization ways, the potential barriers during the formation of one ~16 nm nanoparticle are on the order of 10-9 mJ.

  10. Coronene molecules in helium clusters: Quantum and classical studies of energies and configurations

    Energy Technology Data Exchange (ETDEWEB)

    Rodríguez-Cantano, Rocío; Pérez de Tudela, Ricardo; Bartolomei, Massimiliano; Hernández, Marta I.; Campos-Martínez, José; González-Lezana, Tomás, E-mail: t.gonzalez.lezana@csic.es; Villarreal, Pablo [Instituto de Física Fundamental, IFF-CSIC, Serrano 123, 28006 Madrid (Spain); Hernández-Rojas, Javier; Bretón, José [Departamento de Física and IUdEA, Universidad de La Laguna, 38205 Tenerife (Spain)

    2015-12-14

    Coronene-doped helium clusters have been studied by means of classical and quantum mechanical (QM) methods using a recently developed He–C{sub 24}H{sub 12} global potential based on the use of optimized atom-bond improved Lennard-Jones functions. Equilibrium energies and geometries at global and local minima for systems with up to 69 He atoms were calculated by means of an evolutive algorithm and a basin-hopping approach and compared with results from path integral Monte Carlo (PIMC) calculations at 2 K. A detailed analysis performed for the smallest sizes shows that the precise localization of the He atoms forming the first solvation layer over the molecular substrate is affected by differences between relative potential minima. The comparison of the PIMC results with the predictions from the classical approaches and with diffusion Monte Carlo results allows to examine the importance of both the QM and thermal effects.

  11. The effect of the configuration and the interior design of a virtual weightless space station on human spatial orientation.

    Science.gov (United States)

    Aoki, Hirofumi; Ohno, Ryuzo; Yamaguchi, Takao

    2005-01-01

    In a virtual weightless environment, subjects' orientation skills were studied to examine what kind of cognitive errors people make when they moved through the interior space of virtual space stations and what kind of visual information effectively decreases those errors. Subjects wearing a head-mounted display moved from one end to the other end in space station-like routes constructed of rectangular and cubical modules, and did Pointing and Modeling tasks. In Experiment 1, configurations of the routes were changed with such variables as the number of bends, the number of embedding planes, and the number of planes with respect to the body posture. The results indicated that spatial orientation ability was relevant to the variables and that orientational errors were explained by two causes. One of these was that the place, the direction, and the sequence of turns were incorrect. The other was that subjects did not recognize the rotation of the frame of reference, especially when they turned in pitch direction rather than in yaw. In Experiment 2, the effect of the interior design was examined by testing three design settings. Wall colors that showed the allocentric frame of reference and the different interior design of vertical and horizontal modules were effective; however, there was a limit to the effectiveness in complicated configurations. c2005 Published by Elsevier Ltd.

  12. RotCFD: A Viscous Design Tool for Advanced Configurations Project

    Data.gov (United States)

    National Aeronautics and Space Administration — The incorporation of viscous analysis in design is vital for a complete understanding of aerodynamic problems. This proposal offers to develop and integrate with...

  13. Study of advanced composite structural design concepts for an arrow wing supersonic cruise configuration

    Science.gov (United States)

    Turner, M. J.; Grande, D. L.

    1978-01-01

    Based on estimated graphite and boron fiber properties, allowable stresses and strains were established for advanced composite materials. Stiffened panel and conventional sandwich panel concepts were designed and analyzed, using graphite/polyimide and boron/polyimide materials. The conventional sandwich panel was elected as the structural concept for the modified wing structure. Upper and lower surface panels of the arrow wing structure were then redesigned, using high strength graphite/polyimide sandwich panels, retaining the titanium spars and ribs from the prior study. The ATLAS integrated analysis and design system was used for stress analysis and automated resizing of surface panels. Flutter analysis of the hybrid structure showed a significant decrease in flutter speed relative to the titanium wing design. The flutter speed was increased to that of the titanium design by selective increase in laminate thickness and by using graphite fibers with properties intermediate between high strength and high modulus values.

  14. Design and Development of a Configurable Fault-Tolerant Processor (CFTP) for Space Applications

    Science.gov (United States)

    2003-06-01

    two central devices, while the remainder of the design was a tabula rasa . The legacy components were SRAM and an FPGA. SRAM provided the CPE’s prin...the most sig- nificant role in the failure of electronic equipment in orbit. There exists a wide range of these circuit-crippling events, including...such, the goals of the CFTP project are the most rigorous constraints applied on the design process, and are what will ensure its future role as an

  15. Design Of Digital Configurable Error Free Frequency Detector Using Strobe Signal.

    Directory of Open Access Journals (Sweden)

    Sayannika Banik,

    2014-04-01

    Full Text Available This paper presents a glitch free module using strobe signal which overcomes the limitation of delay mismatch in a wide range of applications. The proposed strobe signal logic can control the occurrence of glitch at both the rising edge and falling edge of the circuit. The theoretical demonstration of the glitch free operation of the proposed strobe signal module is also derived in the paper. The previously proposed digitally controlled delay lines (DCDL has been compared to this technology. Simulation results show the correctness of the module with no delay mismatch with respect to the previously proposed DCDL. As an example application, the strobe signal logic is used in configurable error free frequency detector (a frequency counter which can control the occurrence of glitch during the sudden modulation of the frequency. The employ of the proposed strobe signal can hold the operation of the gate for a specific time until the other gate completes its operation so that there is no delay mismatch.

  16. Multi-Objective Optimization Design for a Hybrid Energy System Using the Genetic Algorithm

    Directory of Open Access Journals (Sweden)

    Myeong Jin Ko

    2015-04-01

    Full Text Available To secure a stable energy supply and bring renewable energy to buildings within a reasonable cost range, a hybrid energy system (HES that integrates both fossil fuel energy systems (FFESs and new and renewable energy systems (NRESs needs to be designed and applied. This paper presents a methodology to optimize a HES consisting of three types of NRESs and six types of FFESs while simultaneously minimizing life cycle cost (LCC, maximizing penetration of renewable energy and minimizing annual greenhouse gas (GHG emissions. An elitist non-dominated sorting genetic algorithm is utilized for multi-objective optimization. As an example, we have designed the optimal configuration and sizing for a HES in an elementary school. The evolution of Pareto-optimal solutions according to the variation in the economic, technical and environmental objective functions through generations is discussed. The pair wise trade-offs among the three objectives are also examined.

  17. Experimental study of the lift and drag characteristics of a cascade of flat plates in a configuration of interest for tidal energy converters

    Science.gov (United States)

    Fedoul, Faical; Parras, Luis; Del Pino, Carlos; Fernandez-Feria, Ramon

    2012-11-01

    Wind tunnel experiments are conducted for the flow around both a single flat plate and a cascade of three parallel flat plates at different angles of incidence to compare their lift and drag coefficients in a range of Reynolds number about 105, and for two values of the aspect ratio of the flat plates. The selected cascade configuration is of interest for a particular type of tidal energy converter. The lift and drag characteristics of the central plate in the cascade are compared to those of the isolated plate, finding that there exist an angle of incidence, which depends on the Reynolds number and the aspect ratio, above which the effective lift of the plate in the cascade becomes larger than that of an isolated plate. These experimental results, which are also analyzed in the light of theoretical predictions, are used as a guide for the design of the optimum configuration of the cascade which extracts the maximum power from a tidal current for a given value of the Reynolds number. Supported by the Ministerio de Ciencia e Innovacion (Spain) Grant no. ENE2010-16851.

  18. Energy Design Guidelines for High Performance Schools: Tropical Island Climates

    Energy Technology Data Exchange (ETDEWEB)

    None

    2004-11-01

    Design guidelines outline high performance principles for the new or retrofit design of K-12 schools in tropical island climates. By incorporating energy improvements into construction or renovation plans, schools can reduce energy consumption and costs.

  19. Aerodynamic Design of Integrated Propulsion-Airframe Configuration of the Hybrid Wing-Body Aircraft

    Science.gov (United States)

    Liou, May-Fun; Kim, Hyoungjin; Lee, B. J.; Liou, Meng-Sing

    2017-01-01

    Hybrid Wing Body (HWB) aircraft is characterized by a flattened and airfoil-shaped body, which produces a substantial portion of the total lift. The body form is composed of distinct and separate wing structures, though the wings are smoothly blended into the body. This concept has been studied widely and results suggest remarkable performance improvements over the conventional tube and wing transport1,2. HWB incorporates design features from both a futuristic fuselage and flying wing design, which houses most of the crew, payload and equipment inside the main centerbody structure.

  20. Optimal design of divertor heat sink with different geometric configurations of sectorial extended surfaces

    Energy Technology Data Exchange (ETDEWEB)

    Rimza, Sandeep, E-mail: sandeepr@ipr.res.in [Divertor and First Wall Technology Development Division, Institute for Plasma Research (IPR), Bhat – 382428, Gandhinagar, Gujarat (India); Satpathy, Kamalakanta, E-mail: satpathy@ipr.res.in [Divertor and First Wall Technology Development Division, Institute for Plasma Research (IPR), Bhat – 382428, Gandhinagar, Gujarat (India); Khirwadkar, Samir, E-mail: sameer@ipr.res.in [Divertor and First Wall Technology Development Division, Institute for Plasma Research (IPR), Bhat – 382428, Gandhinagar, Gujarat (India); Velusamy, Karupanna, E-mail: kvelu@igcar.gov.in [Mechanics and Hydraulics Division, Indira Gandhi Centre for Atomic Research (IGCAR), Kalpakkam 603102 (India)

    2015-11-15

    Highlights: • Effect of design variables in enhancing heat removal potential with pumping power assessed. • The optimization objective is to minimize the thimble temperature. • Investigation of optimum design parameters for various Reynolds number. • Practicability of the optimum designs is verified through structural analysis. • Benchmark validation of divertor finger mock-up against in-house experiment and good agreement is achieved. - Abstract: Cooling of fusion reactor divertor by helium is widely accepted due to its chemical and neutronic inertness and superior safety aspect. However, its poor thermo physical characteristics need high pressure to remove large heat flux encountered in fusion power plant (DEMO). In the perspective of DEMO, it is desirable to explore efficient cooling technology for divertor that can handle high heat flux. Toward this, a novel sectorial extended surface (SES) was proposed by the authors Rimza et al. (2014) [2]. The present work focuses on design optimization of divertor finger mock-up with SES to enhance the thermal hydraulic performance. The maximum thimble temperature is considered as the vital design constraint. Various non-dimensional design variables, viz., relative pitch, thickness, jet diameter, the ratio of height of SES to jet diameter and circumferential position of the SES are considered for the present optimization study. The effects of design variables on thermal performance of the divertor are evaluated in the Reynolds number (Re) range of 7.5 × 10{sup 4}–1.2 × 10{sup 5}. The analysis reveals that, the heat transfer performance of divertor finger mock-up with SES is improved for two optimum designs having relative pitch and thickness of 0.30 and 0.56, respectively. Also, it is observed that finger mock-up heat sink with SES performs better, when the ratio of SES height to jet diameter, reduces to 0.75 at the cost of marginally higher pumping power. The effects of jet diameter and circumferential

  1. Energy efficient building design. A transfer guide for local governments

    Energy Technology Data Exchange (ETDEWEB)

    1992-03-01

    The fundamental concepts of the building design process, energy codes and standards, and energy budgets are introduced. These tools were combined into Energy Design Guidelines and design contract requirements. The Guidelines were repackaged for a national audience and a videotape for selling the concept to government executives. An effort to test transfer of the Guidelines to outside agencies is described.

  2. Design of high energy density thermoelectric energy conversion unit by using FGM compliant pads

    CERN Document Server

    Kambe, M

    1999-01-01

    In order to provide increasingly large amounts of electrical power to space and terrestrial systems with a sufficiently high level of reliability at a reasonable cost, thermoelectric (TE) energy conversion system by using $9 functionally graded material (FGM) compliant pads has been focused. To achieve high thermal energy density in TE power conversion systems, conductively coupling the TE units to the hot and cold heat exchangers is the most effective $9 configuration. This is accomplished by two sets of FGM compliant pads. This design strategy provides (1) a high flux, direct conduction path to heat source and heat sink, (2) the structural flexibility to protect the cell from high $9 stress due to thermal expansion, (3) an extended durability by a simple FGM structure, and (4) manufacturing cost reduction by spark plasma sintering. High thermal energy density of ten times as much as conventional radioisotope $9 thermoelectric generator is expected. Manufacturing of Cu/Al/sub 2/O/sub 3//Cu symmetrical FGM co...

  3. Rapidly Re-Configurable Flight Simulator Tools for Crew Vehicle Integration Research and Design

    Science.gov (United States)

    Pritchett, Amy R.

    2002-01-01

    While simulation is a valuable research and design tool, the time and difficulty required to create new simulations (or re-use existing simulations) often limits their application. This report describes the design of the software architecture for the Reconfigurable Flight Simulator (RFS), which provides a robust simulation framework that allows the simulator to fulfill multiple research and development goals. The core of the architecture provides the interface standards for simulation components, registers and initializes components, and handles the communication between simulation components. The simulation components are each a pre-compiled library 'plugin' module. This modularity allows independent development and sharing of individual simulation components. Additional interfaces can be provided through the use of Object Data/Method Extensions (OD/ME). RFS provides a programmable run-time environment for real-time access and manipulation, and has networking capabilities using the High Level Architecture (HLA).

  4. Strategic Lean Organizational Design: Towards Lean World-Small World Configurations through Discrete Dynamic Organizational Motifs

    Directory of Open Access Journals (Sweden)

    Javier Villalba-Diez

    2016-01-01

    Full Text Available Organizations face strong international competition in the global market arena in achieving strategic goals such as high quality of product or service at lower cost while increasing their ability to respond quickly to requirements of the market. These challenges concern strategically designing organizations that can meet global challenges and specialize locally to meet performance constraints. After introducing the concept of organizational functional and structural motifs as small organizational building block, our findings suggest the hypothesis that a strategic organizational design (SOD approach to meet these challenges involves maximizing the number and diversity of functional motifs, while minimizing the repertoire of structural motifs. By detecting characteristic structural motifs, we provide organizational leaders with specific Lean SOD solutions with which to meet local and global challenges simultaneously. As a matter of application, we show the implementation of such an SOD approach in nine US hospitals that form one large health care holding.

  5. Quasi-Monopolar Stimulation: A Novel Electrode Design Configuration for Performance Optimization of a Retinal Neuroprosthesis

    OpenAIRE

    2013-01-01

    In retinal neuroprostheses, spatial interaction between electric fields from various electrodes - electric crosstalk - may occur in multielectrode arrays during simultaneous stimulation of the retina. Depending on the electrode design and placement, this crosstalk can either enhance or degrade the functional characteristics of a visual prosthesis. To optimize the device performance, a balance must be satisfied between the constructive interference of crosstalk on dynamic range and power consu...

  6. Plasma grid design for optimized filter field configuration for the NBI test facility ELISE

    Energy Technology Data Exchange (ETDEWEB)

    Nocentini, R. [Max-Planck-Institut fuer Plasmaphysik, EURATOM Association, D-85740 Garching (Germany)], E-mail: riccardo.nocentini@ipp.mpg.de; Gutser, R.; Heinemann, B.; Froeschle, M.; Riedl, R. [Max-Planck-Institut fuer Plasmaphysik, EURATOM Association, D-85740 Garching (Germany)

    2009-12-15

    Maintenance-free RF sources for negative hydrogen ions with moderate extraction areas (100-200 cm{sup 2}) have been successfully developed in the last years at IPP Garching in the test facilities BATMAN and MANITU. A facility with larger extraction area (1000 cm{sup 2}), ELISE, is being designed with a 'half-size' ITER-like extraction system, pulsed ion acceleration up to 60 kV for 10 s and plasma generation up to 1 h. Due to the large size of the source, the magnetic filter field (FF) cannot be produced solely by permanent magnets. Therefore, an additional magnetic field produced by current flowing through the plasma grid (PG current) is required. The filter field homogeneity and the interaction with the electron suppression magnetic field have been studied in detail by finite element method (FEM) during the ELISE design phase. Significant improvements regarding the field homogeneity have been introduced compared to the ITER reference design. Also, for the same PG current a 50% higher field in front of the grid has been achieved by optimizing the plasma grid geometry. Hollow spaces have been introduced in the plasma grid for a more homogeneous PG current distribution. The introduction of hollow spaces also allows the insertion of permanent magnets in the plasma grid.

  7. A Novel and Generalized Lithium-Ion-Battery Configuration utilizing Al Foil as Both Anode and Current Collector for Enhanced Energy Density.

    Science.gov (United States)

    Ji, Bifa; Zhang, Fan; Sheng, Maohua; Tong, Xuefeng; Tang, Yongbing

    2017-02-01

    A novel battery configuration based on an aluminum foil anode and a conventional cathode is developed. The aluminum foil plays a dual role as both the active anode material and the current collector, which enhances the energy density of the packaged battery, and reduces the production cost. This generalized battery configuration has high potential for application in next-generation lithium-ion batteries. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  8. Technical and economic assessment of fluidized bed augmented compressed air energy storage system. Volume III. Preconceptual design

    Energy Technology Data Exchange (ETDEWEB)

    Giramonti, A.J.; Lessard, R.D.; Merrick, D.; Hobson, M.J.

    1981-09-01

    A technical and economic assessment of fluidized bed combustion augmented compressed air energy storage systems is presented. The results of this assessment effort are presented in three volumes. Volume III - Preconceptual Design contains the system analysis which led to the identification of a preferred component configuration for a fluidized bed combustion augmented compressed air energy storage system, the results of the effort which transformed the preferred configuration into preconceptual power plant design, and an introductory evaluation of the performance of the power plant system during part-load operation and while load following.

  9. Information configuration?

    OpenAIRE

    Lauro Cesar Araujo; Mamede Lima-Marques

    2016-01-01

    Introduction: The term "configuration information" has emerged in the works of Information Architecture; however, there isn’t a conceptualization of “configuration” within Information Architecture. Objective: The objective is propose a definition for "configuration" and "information configuration" within the Information Architecture discipline, and indicate a teleological corpus from configuration management that can be used as paxis in Information Architecture. Methodolo...

  10. Design and control strategy for a hybrid green energy system for mobile telecommunication sites

    Science.gov (United States)

    Okundamiya, Michael S.; Emagbetere, Joy O.; Ogujor, Emmanuel A.

    2014-07-01

    The rising energy costs and carbon footprint of operating mobile telecommunication sites in the emerging world have increased research interests in green technology. The intermittent nature of most green energy sources creates the problem of designing the optimum configuration for a given location. This study presents the design analysis and control strategy for a cost effective and reliable operation of the hybrid green energy system (HGES) for GSM base transceiver station (BTS) sites in isolated regions. The design constrains the generation and distribution of power to reliably satisfy the energy demand while ensuring safe operation of the system. The overall process control applies the genetic algorithm-based technique for optimal techno-economic sizing of system's components. The process simulation utilized meteorological data for 3 locations (Abuja, Benin City and Sokoto) with varying climatic conditions in Nigeria. Simulation results presented for green GSM BTS sites are discussed and compared with existing approaches.

  11. Energy efficient circuit design using nanoelectromechanical relays

    Science.gov (United States)

    Venkatasubramanian, Ramakrishnan

    Nano-electromechanical (NEM) relays are a promising class of emerging devices that offer zero off-state leakage and behave like an ideal switch. Recent advances in planar fabrication technology have demonstrated that microelectromechanical (MEMS) scale miniature relays could be manufactured reliably and could be used to build fully functional, complex integrated circuits. The zero leakage operation of relays has renewed the interest in relay based low power logic design. This dissertation explores circuit architectures using NEM relays and NEMS-CMOS heterogeneous integration. Novel circuit topologies for sequential logic, memory, and power management circuits have been proposed taking into consideration the NEM relay device properties and optimizing for energy efficiency and area. In nanoscale electromechanical devices, dispersion forces like Van der Waals' force (vdW) affect the pull-in stability of the relay devices significantly. Verilog-A electromechanical model of the suspended gate relay operating at 1V with a nominal air gap of 5 - 10nm has been developed taking into account all the electrical, mechanical and dispersion effects. This dissertation explores different relay based latch and flip-flop topologies. It has been shown that as few as 4 relay cells could be used to build flip-flops. An integrated voltage doubler based flip flop that improves the performance by 2X by overdriving Vgb has been proposed. Three NEM relay based parallel readout memory bitcell architectures have been proposed that have faster access time, and remove the reliability issues associated with previously reported serial readout architectures. A paradigm shift in design of power switches using NEM relays is proposed. An interesting property of the relay device is that the ON state resistance (Ron) of the NEM relay switch is constant and is insensitive to the gate slew rate. This coupled with infinite OFF state resistance (Roff ) offers significant area and power advantages over CMOS

  12. Energy Conservation of the Designated Government Buildings in Thailand

    Directory of Open Access Journals (Sweden)

    Wangskarn Prapat

    2016-01-01

    Full Text Available The designated government buildings have implemented and administered energy program under the energy development and promotion Act 2007 for many years continuously until 2015. Appointment person responsible for energy, performing energy management and implementing the energy conservation work plan and measures are legal requirements for the designated buildings. Therefore, the ministry of Energy has launched the project to support the implementation of energy management. The aim of the project was to create the energy management system in the designated government buildings, and to reduce energy consumption. In this paper, the evaluation of the project has been presented from the achievements of 839 designated government buildings. The energy saving is more than 440 ktoe/year. This is about 3% of energy consumptions of buildings.

  13. Crisis crowdsourcing framework: designing strategic configurations of crowdsourcing for the emergency management domain

    Science.gov (United States)

    Liu, Sophia B.

    2014-01-01

    Crowdsourcing is not a new practice but it is a concept that has gained significant attention during recent disasters. Drawing from previous work in the crisis informatics, disaster sociology, and computer-supported cooperative work (CSCW) literature, the paper first explains recent conceptualizations of crowdsourcing and how crowdsourcing is a way of leveraging disaster convergence. The CSCW concept of “articulation work” is introduced as an interpretive frame for extracting the salient dimensions of “crisis crowdsourcing.” Then, a series of vignettes are presented to illustrate the evolution of crisis crowdsourcing that spontaneously emerged after the 2010 Haiti earthquake and evolved to more established forms of public engagement during crises. The best practices extracted from the vignettes clarified the efforts to formalize crisis crowdsourcing through the development of innovative interfaces designed to support the articulation work needed to facilitate spontaneous volunteer efforts. Extracting these best practices led to the development of a conceptual framework that unpacks the key dimensions of crisis crowdsourcing. The Crisis Crowdsourcing Framework is a systematic, problem-driven approach to determining the why, who, what, when, where, and how aspects of a crowdsourcing system. The framework also draws attention to the social, technological, organizational, and policy (STOP) interfaces that need to be designed to manage the articulation work involved with reducing the complexity of coordinating across these key dimensions. An example of how to apply the framework to design a crowdsourcing system is offered with with a discussion on the implications for applying this framework as well as the limitations of this framework. Innovation is occurring at the social, technological, organizational, and policy interfaces enabling crowdsourcing to be operationalized and integrated into official products and services.

  14. Orientation of bluff body for designing efficient energy harvesters from vortex-induced vibrations

    Energy Technology Data Exchange (ETDEWEB)

    Dai, H. L. [Department of Mechanics, Huazhong University of Science and Technology, Wuhan 430074 (China); School of Civil and Environmental Engineering, Nanyang Technological University, Singapore 639798 (Singapore); Abdelkefi, A. [Department of Mechanical and Aerospace Engineering, New Mexico State University, Las Cruces, New Mexico 88003 (United States); Yang, Y., E-mail: cywyang@ntu.edu.sg [School of Civil and Environmental Engineering, Nanyang Technological University, Singapore 639798 (Singapore); Wang, L. [Department of Mechanics, Huazhong University of Science and Technology, Wuhan 430074 (China)

    2016-02-01

    The characteristics and performances of four distinct vortex-induced vibrations (VIVs) piezoelectric energy harvesters are experimentally investigated and compared. The difference between these VIV energy harvesters is the installation of the cylindrical bluff body at the tip of cantilever beam with different orientations (bottom, top, horizontal, and vertical). Experiments show that the synchronization regions of the bottom, top, and horizontal configurations are almost the same at low wind speeds (around 1.5 m/s). The vertical configuration has the highest wind speed for synchronization (around 3.5 m/s) with the largest harvested power, which is explained by its highest natural frequency and the smallest coupled damping. The results lead to the conclusion that to design efficient VIV energy harvesters, the bluff body should be aligned with the beam for low wind speeds (<2 m/s) and perpendicular to the beam at high wind speeds (>2 m/s)

  15. Energy efficient design for residential buildings in China

    Institute of Scientific and Technical Information of China (English)

    R.YAO; K.STEEMERS; B.LI

    2003-01-01

    This paper illustrates an integrated energy design model based on the energy balance of a single zone. The results of energy efficient residential building design for the different climate zones of China by implementing an integrated energy model have been presented. Optimum measures of building design for typical Chinese residential buildings are introduced, with the objective of minimizingannual energy consumption for those buildings and improving thermal comfort. One overriding conclusion is that significant energy savings and thermal comfort can be achieved though optimum design.

  16. Loop-driven graphical unitary group approach to the electron correlation problem, including configuration interaction energy gradients

    Energy Technology Data Exchange (ETDEWEB)

    Brooks, B.R.

    1979-09-01

    The Graphical Unitary Group Approach (GUGA) was cast into an extraordinarily powerful form by restructuring the Hamiltonian in terms of loop types. This restructuring allows the adoption of the loop-driven formulation which illuminates vast numbers of previously unappreciated relationships between otherwise distinct Hamiltonian matrix elements. The theoretical/methodological contributions made here include the development of the loop-driven formula generation algorithm, a solution of the upper walk problem used to develop a loop breakdown algorithm, the restriction of configuration space employed to the multireference interacting space, and the restructuring of the Hamiltonian in terms of loop types. Several other developments are presented and discussed. Among these developments are the use of new segment coefficients, improvements in the loop-driven algorithm, implicit generation of loops wholly within the external space adapted within the framework of the loop-driven methodology, and comparisons of the diagonalization tape method to the direct method. It is also shown how it is possible to implement the GUGA method without the time-consuming full (m/sup 5/) four-index transformation. A particularly promising new direction presented here involves the use of the GUGA methodology to obtain one-electron and two-electron density matrices. Once these are known, analytical gradients (first derivatives) of the CI potential energy are easily obtained. Several test calculations are examined in detail to illustrate the unique features of the method. Also included is a calculation on the asymmetric 2/sup 1/A' state of SO/sub 2/ with 23,613 configurations to demonstrate methods for the diagonalization of very large matrices on a minicomputer. 6 figures, 6 tables.

  17. Economics and energy conservation in the design of new single-family housing

    Science.gov (United States)

    Petersen, S. R.

    1981-08-01

    The extent to which certain energy conservation modifications to the envelope design of a new, single family house are economically justified for a wide range of climates and projected energy costs were investigated factors that give rise to space heating and cooling loads in buildings are provided thermal inter-dependencies within and among envelope components that can greatly affect heating and cooling loads are examined. Economic criteria for determining a minimum life cycle cost building envelope design are formulated and a priority ranking method is developed to assist in the calculation of these designs. An expanded version of the NBS load determination program is used to calculated the annual heating and cooling requirements and maximum heating and cooling loads for a 1200 square foot, wood frame house with a wide range of thermal improvements in 14 geographic locations. It is demonstrated that the optimal envelope design configuration varies over a wide rang depending on climate, energy costs, and modification costs.

  18. Design and testing of a uniformly solar energy TIR-R concentration lenses for HCPV systems.

    Science.gov (United States)

    Shen, S C; Chang, S J; Yeh, C Y; Teng, P C

    2013-11-04

    In this paper, total internal reflection-refraction (TIR-R) concentration (U-TIR-R-C) lens module were designed for uniformity using the energy configuration method to eliminate hot spots on the surface of solar cell and increase conversion efficiency. The design of most current solar concentrators emphasizes the high-power concentration of solar energy, however neglects the conversion inefficiency resulting from hot spots generated by uneven distributions of solar energy concentrated on solar cells. The energy configuration method proposed in this study employs the concept of ray tracing to uniformly distribute solar energy to solar cells through a U-TIR-R-C lens module. The U-TIR-R-C lens module adopted in this study possessed a 76-mm diameter, a 41-mm thickness, concentration ratio of 1134 Suns, 82.6% optical efficiency, and 94.7% uniformity. The experiments demonstrated that the U-TIR-R-C lens module reduced the core temperature of the solar cell from 108 °C to 69 °C and the overall temperature difference from 45 °C to 10 °C, and effectively relative increased the conversion efficiency by approximately 3.8%. Therefore, the U-TIR-R-C lens module designed can effectively concentrate a large area of sunlight onto a small solar cell, and the concentrated solar energy can be evenly distributed in the solar cell to achieve uniform irradiance and effectively eliminate hot spots.

  19. Reactor and process design in sustainable energy technology

    CERN Document Server

    Shi, Fan

    2014-01-01

    Reactor Process Design in Sustainable Energy Technology compiles and explains current developments in reactor and process design in sustainable energy technologies, including optimization and scale-up methodologies and numerical methods. Sustainable energy technologies that require more efficient means of converting and utilizing energy can help provide for burgeoning global energy demand while reducing anthropogenic carbon dioxide emissions associated with energy production. The book, contributed by an international team of academic and industry experts in the field, brings numerous reactor design cases to readers based on their valuable experience from lab R&D scale to industry levels. It is the first to emphasize reactor engineering in sustainable energy technology discussing design. It provides comprehensive tools and information to help engineers and energy professionals learn, design, and specify chemical reactors and processes confidently. Emphasis on reactor engineering in sustainable energy techn...

  20. Keyboard Design Producing its Own Energy

    OpenAIRE

    ŞENYUREK, Alper; Demetgul, Mustafa

    2015-01-01

    The development in production has posed circuit patterns operating in low energy and network techniques. Therefore the energy requirements for electronic devices have decreased. With decreased demand in energy systems, besides the probable use of devices alternative to batteries, new devices have been emerged. Piezoelectric materials have been used in power operated devices in order to capture the kinetic energy in the media and to convert it into usable electrical energy. In this work piezo ...

  1. HLT configuration management system

    CERN Document Server

    Daponte, Vincenzo

    2015-01-01

    The CMS High Level Trigger (HLT) is implemented running a streamlined version of the CMS offline reconstruction software running on thousands of CPUs. The CMS software is written mostly in C++, using Python as its configuration language through an embedded CPython interpreter. The configuration of each process is made up of hundreds of modules, organized in sequences and paths. As an example, the HLT configurations used for 2011 data taking comprised over 2200 different modules, organized in more than 400 independent trigger paths. The complexity of the HLT configurations and the large number of configuration produced require the design of a suitable data management system. The present work describes the designed solution to manage the considerable number of configurations developed and to assist the editing of new configurations. The system is required to be remotely accessible and OS-independent as well as easly maintainable easy to use. To meet these requirements a three-layers architecture has been choose...

  2. Quality by Design approach in the development of a magnetic transducer for biomedical measurements: preliminary results on Design Space configuration

    Science.gov (United States)

    Louzada, D. R.; Monteiro, E. C.; Rivero, A. M.; Fortaleza, L. G. S.; Barbosa, C. R. H.; Velázquez, D. R. T.; Silva, E. C.; Gusmão, L. A. P.

    2016-11-01

    The concept of Quality by Design (QbD) has been widely used by the pharmaceutical industry since 2004, changing the focus on inspections to embrace greater control in the manufacturing process. This new approach contributed to lower production costs and higher quality of medicines. This work discusses the first steps towards the implementation of a QbD approach aimed at ensuring the quality of a biomedical device under development. This device will be applied as a non-magnetic metallic foreign body localization system for surgical removal guidance. It should be highlighted that a new approach was used to define the Design Space, based on fuzzy logic rather than the typical statistical techniques.

  3. Multi-configuration Dirac-Hartree-Fock calculations of excitation energies, oscillator strengths and hyperfine structure constants for low-lying levels of Sm I

    CERN Document Server

    Zhou, Fuyang; Li, Jiguang; Wang, Jianguo

    2015-01-01

    The multi-configuration Dirac-Hartree-Fock method was employed to calculate the total and excitation energies, oscillator strengths and hyperfine structure constants for low-lying levels of Sm I. In the first-order perturbation approximation, we systematically analyzed correlation effects from each electrons and electron pairs. It was found that the core correlations are of importance for physical quantities concerned. Based on the analysis, the important configuration state wave functions were selected to constitute atomic state wave functions. By using this computational model, our excitation energies, oscillator strengths, and hyperfine structure constants are in better agreement with experimental values than earlier theoretical works.

  4. Innovative Breakwaters Design for Wave Energy Conversion

    DEFF Research Database (Denmark)

    Vicinanza, Diego; Stagonas, D.; Müller, G.

    2012-01-01

    This paper intends contributing to an economically and environmentally sustainable development of coastal infrastructures by investigating the possibility of combining together breakwaters and Wave Energy Converters (WEC). The latter change the wave energy to electricity, which may serve both the...

  5. Smart heat guide: designing efficiently with ambient thermal energy

    NARCIS (Netherlands)

    Fremouw, M.

    2012-01-01

    This "designers' manual" is made during the TIDO-course AR0531 Smart & Bioclimatic Design. There are a few issues in our current energy use. We do not know how long the finite primary sources will last. The process of energy conversion makes very inefficient use of the primary energy sources. There

  6. Ocean thermal energy conversion (OTEC) platform configuration and integration. Final report. Volume I. Systems requirements and evaluation

    Energy Technology Data Exchange (ETDEWEB)

    None

    1978-06-01

    Studies leading to the development of two 400 MW Offshore Thermal Energy Conversion Commercial Plants are presented. This volume includes a summary of three tasks: task IIA--systems evaluation and requirements; task IIB--evaluation plan; task III--technology review; and task IV--systems integration evaluation. Task IIA includes the definition of top level requirements and an assessment of factors critical to the selection of hull configuration and size, quantification of payload requirements and characteristics, and sensitivity of system characteristics to site selection. Task IIB includes development of a methodology for systematically evaluating the candidate hullforms, based on interrelationships and priorities developed during task IIA. Task III includes the assessment of current technology and identification of deficiencies in relation to OTEC requirements and the development of plans to correct such deficiencies. Task IV involves the formal evaluation of the six candidate hullforms in relation to sit and plant capacity to quantify cost/size/capability relationships, leading to selection of an optimum commercial plant. (WHK)

  7. Control mechanism for attenuation of thermal energy pulses using cold circulators in the cryogenic distribution system of fusion devices in tokamak configuration

    Science.gov (United States)

    Bhattacharya, R.; Sarkar, B.; Vaghela, H.; Shah, N.

    2014-01-01

    Operation and control of superconducting (SC) magnets in the fusion devices having tokamak configuration opens up the domain of varying peak thermal energy environment as a function of time, commensurate with the plasma pulses. The varied thermal energy environment, thus propagated to upstream of the cooling system, is responsible for the system level instability of the overall cryogenic system. The cryogenic distribution system, the regime of first impact point, therefore, has to be tuned so as to stay at the nearly stable zone of operation. The configuration of the cryogenic distribution system, considered in the present study, involves a liquid helium (LHe) bath as a thermal buffer, LHe submerged heat exchangers and cold circulator apart from the valves for implementations of the precise controls. The cold circulator supplies the forced flow supercritical helium, used for the cooling of SC magnets. The transients of the thermal energy pulses can be attenuated in the cryogenic distribution system by various methodologies. One of the adopted methodologies in the present study is with the precise speed control of the cold circulators. The adopted methodology is applied to various configurations of arrangements of internal components in the distribution system for obtaining system responses with superior attenuation of energy pulses. The process simulation approach, assumptions, considered inputs and constraints, process modeling with different configuration as well as results to accomplish the control scheme for the attenuation of the thermal energy pulses are described.

  8. Power and Energy Aware Design of an Autonomous Wireless Sensor Node

    Directory of Open Access Journals (Sweden)

    Nicolas Ferry

    2013-09-01

    Full Text Available The design of Wireless Sensor Networks is a challenge, requiring to correctly balancing between performance, time, cost and energy. But the main problem with rechargeable WSNs is to predict at design time which will be the total system autonomy. Moreover, it depends on the energy harvested from the environment, and we know that weather may be very unsettled. Thus, it is crucial to design and fine scale the entire power supply chain in order to produce a robust WSN. In this article, we propose an energy estimator able to handle environment like weather parameters to estimate the system autonomy. The key innovation comes from the capability to dynamically rebuild the models all along the project evolution with real measurements on the hardware and to include weather forecasts as dynamic parameters of the DPM policy. Finally, we have experiment various configurations and compared the hardware WSN against the simulator. The results have validated the relevance of the estimator for prospecting various energy problems. By experiment, the estimator has shown that most environmental energy was wasted due to the battery charging constraints. This will foresee the opportunities of energy gains, and the definition of newer extra power modes for the Dynamic Power Management. This work contributes to the domain for WSN design methodology, energy scavenging and energy management to optimize system autonomy.

  9. Polysoaps: Configurations and Elasticity

    Science.gov (United States)

    Halperin, A.

    1997-03-01

    Simple polymers are very long, flexible, linear molecules. Amphiphiles, soaps, are small molecules comprising of a part that prefers water over oil and a part that prefers oil over water. By combining the two we arrive at an interesting, little explored, class of materials: Polysoaps. These comprise of a water soluble backbone incorporating, at intervals, covalently bound amphiphilic monomers. In water, the polymerised amphiphiles aggregate into self assembled units known as micelles. This induces a dramatic modification of the spatial configurations of the polymers. What were featureless random coils now exhibit intramolecular, hierachial self organisation. Due to this self organisation it is necessary to modify the paradigms describing the large scale behaviour of these polymers: Their configurations, dimensions and elasticity. Understanding the behaviour of these polymers is of practical interest because of their wide range of industrial applications, ranging from cosmetics to paper coating. It is of fundamental interest because polysoaps are characterised by a rugged free energy landscape that is reminiscent of complex systems such as proteins and glasses. The talk concerns theoretical arguments regarding the following issues: (i) The design parameters that govern the spatial configurations of the polysoaps, (ii) The interaction between polysoaps and free amphiphiles, (iii) The effect of the intramolecular self organisation on the elasticity of the chains.

  10. DESIGN AND IMPLEMENTATION OF A SOLAR ENERGY EDUCATIONAL SET

    Directory of Open Access Journals (Sweden)

    İbrahim SEFA

    2007-03-01

    Full Text Available In this study, an educational tool which can be used to obtain electrical energy from solar energy has been designed and implemented. The obtained energy can be used both for direct current and alternating current. Moreover, the energy can be charged into an accumulator group on request. Several experiments related to obtaining electrical energy from solar energy, storing the energy and conversion systems are prepared on the developed educational set. The educational set presented in this paper can be used as an educational tool for increasing knowledge, skill and abilities of students about the converting solar energy to the electrical energy.

  11. Design guidelines for energy-efficient hotels in Nepal

    Directory of Open Access Journals (Sweden)

    Susanne Bodach

    2016-12-01

    Full Text Available It is predicted that the major increase in energy consumption and, thus, carbon emissions, will happen in the developing world. However, in most developing countries the knowledge about energy efficiency, particularly in the building sector, is quite low. Strategies developed for industrialised countries might not be suitable or must be adapted for the very different context of developing countries. This research aims to find energy-efficient and cost-effective building design options for the case of Nepal. Energy-efficient building design is a non-trivial issue involving a number of interdependent design criteria. Particularly, in composite climates, passive design strategies might conflict each other leading to an inefficient building design. This paper explores the energy conservation potential in hotel design for all bioclimatic zones of Nepal using building energy simulation with parametric analysis. Based on extensive field studies, reference models for typical hotel buildings ranging from small-scale resort hotels to large-scale multi-storey hotels were developed. These reference designs were optimised by varying design parameters such as window-to-wall ratio, glazing material, shading devices, glazing type and insulation levels. During the design optimisation, energy demand as well as cost effectiveness were evaluated. Finally, recommendations for energy-efficient and cost-effective hotel design solutions were suggested. In addition, the bioclimatic zoning for Nepal was consolidated leading to five elevation-based zones that can be used to introduce building energy regulations in the future.

  12. Field Evaluation of Four Novel Roof Designs for Energy-Efficient Manufactured Homes

    Energy Technology Data Exchange (ETDEWEB)

    Levy, E. [ARIES Collaborative, New York, NY (United States); Dentz, J. [ARIES Collaborative, New York, NY (United States); Ansanelli, E. [ARIES Collaborative, New York, NY (United States); Barker, G. [ARIES Collaborative, New York, NY (United States); Rath, P. [ARIES Collaborative, New York, NY (United States); Dadia, D. [ARIES Collaborative, New York, NY (United States)

    2015-12-03

    "9A five-bay roof test structure was built, instrumented and monitored in an effort to determine through field testing and analysis the relative contributions of select technologies toward reducing energy use in new manufactured homes. The roof structure in Jamestown, California was designed to examine how differences in roof construction impact space conditioning loads, wood moisture content and attic humidity levels. Conclusions are drawn from the data on the relative energy and moisture performance of various configurations of vented and sealed attics.

  13. Designing anthropological reflection within an energy company

    DEFF Research Database (Denmark)

    Løgstrup, Louise Buch; Gunn, Wendy; Said Mosleh, Wafa

    2013-01-01

    The move towards a more liberalized energy market and the emergent smart grid technology has forced a Scandinavian energy company to begin rethinking the relation between themselves and private energy end users. Originally a unidirectional relationship, the present and future have potential...... ethnographic methods to investigate the system effect of private households’ participation. Our paper questions why this kind of approach is reproducing the unidirectional relationship instead of creating a bidirectional relationship. We propose an extension of the ethnographic approach whereby anthropological...

  14. 高效气动优化设计方法%Efficient Aerodynamic Design Optimization of Complex Configuration

    Institute of Scientific and Technical Information of China (English)

    傅林; 左英桃

    2012-01-01

    基于CFD方法开展气动外形优化设计通常计算量较大,采用离散共轭方法计算目标函数梯度,建立了高效的飞机气动优化设计系统.采用NURBS方法对翼剖面几何外形的扰动量进行参数化,避免了对原始外形的拟合,建立了基于NURBS方法的机翼剖面参数化方法.在复杂外形的优化设计中,动网格方法是关键技术之一,采用无限插值方法生成变形后的网格,并提出采用无限插值方法处理部件之间相贯线发生变化的情况.最后开展了翼身组合体+吊舱+挂架等复杂外形的优化设计,成功地减小了阻力,证明了方法的有效性.%Large scales of computations are required in aerodynamic optimization based on CFD methodologies.Efficient aerodynamic design optimization system is built in this paper,and the gradients of object functions are calculated with discrete adjoint method.The geometric perturbations of wing sections are parameterized with NURBS method,furthermore parameterization methodology of wing based on NURBS are built.Moving grid is one of key technologies in aerodynamic optimization design of very complex configuration.Transfinite interpolation methodology is utilized to generate new grid, and a methodology based on transfinite interpolation technology is proposed to deal with the surface grid in the case of junction lines varying.Configurations including wing - body - nacelle - pylon are optimized with the design optimization system.The drag is reduced successfully, which illustrates the effectiveness of the methodology built in this paper.

  15. Conceptual design of the three-dimensional magnetic field configuration relevant to the magnetopause reconnection in the SPERF

    Science.gov (United States)

    Aohua, MAO; Yang, REN; Hantao, JI; Peng, E.; Ke, HAN; Zhibin, WANG; Qingmei, XIAO; Liyi, LI

    2017-03-01

    A new ground-based experimental device, the Space Plasma Environment Research Facility (SPERF), is being designed at Harbin Institute of Technology in China, with Asymmetric REconnection eXperiment-3 Dimensional (AREX-3D) as one of the experimental components to study the asymmetric reconnection dynamics relevant to the interaction between the interplanetary and magnetospheric plasmas. The asymmetry in the designed magnetic reconnection process not only refers to the distinct plasma parameters designed for the two upstream regions across the current sheet, but also refers to the inhomogeneity in the direction along the current sheet resulting from the designed 3D magnetic field geometry. These two asymmetries are fundamental features of the reconnection process at the Earth’s magnetopause. In experiment, the reconnection process is driven by a set of flux cores through coil-current-ramp-up from the ‘magnetosheath-side’ to interact with a dipole magnetic field generated by the Dipole Research EXperiment (DREX) coil on the ‘magnetosphere-side’. The AREX-3D will be able to investigate a range of important reconnection issues in 3D magnetic field geometry that is relevant to the Earth’s magnetopause. A wide range of plasma parameters can be achieved through inductive plasma generation with flux cores on the ‘magnetosheath-side’ and electron cyclotron resonance (ECR) with microwave sources on the ‘magnetosphere-side’, e.g. high (low) plasma density at experimental magnetosheath (dipole) side. Different reconnection regimes and geometries can be produced by adjusting plasma parameters and coil setups as well as coil current waveforms. The three-dimensional magnetic field configurations in the SPERF relevant to the dayside magnetopause reconnection are discussed in detail.

  16. Design of multi-energy Helds coupling testing system of vertical axis wind power system

    Science.gov (United States)

    Chen, Q.; Yang, Z. X.; Li, G. S.; Song, L.; Ma, C.

    2016-08-01

    The conversion efficiency of wind energy is the focus of researches and concerns as one of the renewable energy. The present methods of enhancing the conversion efficiency are mostly improving the wind rotor structure, optimizing the generator parameters and energy storage controller and so on. Because the conversion process involves in energy conversion of multi-energy fields such as wind energy, mechanical energy and electrical energy, the coupling effect between them will influence the overall conversion efficiency. In this paper, using system integration analysis technology, a testing system based on multi-energy field coupling (MEFC) of vertical axis wind power system is proposed. When the maximum efficiency of wind rotor is satisfied, it can match to the generator function parameters according to the output performance of wind rotor. The voltage controller can transform the unstable electric power to the battery on the basis of optimizing the parameters such as charging times, charging voltage. Through the communication connection and regulation of the upper computer system (UCS), it can make the coupling parameters configure to an optimal state, and it improves the overall conversion efficiency. This method can test the whole wind turbine (WT) performance systematically and evaluate the design parameters effectively. It not only provides a testing method for system structure design and parameter optimization of wind rotor, generator and voltage controller, but also provides a new testing method for the whole performance optimization of vertical axis wind energy conversion system (WECS).

  17. Sustainable energy landscapes : designing, planning, and development

    NARCIS (Netherlands)

    Stremke, S.; Dobbelsteen, van den A.

    2013-01-01

    In the near future the appearance and spatial organization of urban and rural landscapes will be strongly influenced by the generation of renewable energy. One of the critical tasks will be the re-integration of these sustainable energy landscapes into the existing environment—which people value and

  18. Sustainable energy landscapes : designing, planning, and development

    NARCIS (Netherlands)

    Stremke, S.; Dobbelsteen, van den A.

    2013-01-01

    In the near future the appearance and spatial organization of urban and rural landscapes will be strongly influenced by the generation of renewable energy. One of the critical tasks will be the re-integration of these sustainable energy landscapes into the existing environment—which people value and

  19. Energy-efficient adaptive wireless network design

    NARCIS (Netherlands)

    Havinga, Paul J.M.; Smit, Gerardus Johannes Maria; Bos, M.

    Energy efficiency is an important issue for mobile computers since they must rely on their batteries. We present an energy-efficient highly adaptive architecture of a network interface and novel data link layer protocol for wireless networks that provides quality of service (QoS) support for diverse

  20. The ionic states of difluoromethane: A reappraisal of the low energy photoelectron spectrum including ab initio configuration interaction computations

    Science.gov (United States)

    Palmer, Michael H.; Biczysko, Malgorzata; Baiardi, Alberto; Coreno, Marcello; de Simone, Monica; Grazioli, Cesare; Hoffmann, Søren Vrønning; Jones, Nykola C.; Peterson, Kirk A.

    2017-08-01

    A new synchrotron-based study of the photoelectron spectrum (PES) of difluoromethane is interpreted by an ab initio analysis of the ionic states, which includes Franck-Condon (FC) factors. Double differentiation of the spectrum leads to significant spectral sharpening; the vibrational structure observed is now measured with greater accuracy than in previous studies. Several electronic structure methods are used, including equation of motion coupled cluster calculations with single and double excitations (EOM-CCSD), its ionization potential variant EOM-IP-CCSD, 4th order Møller-Plesset perturbation theory (MP4SDQ) configuration interaction (CI), and complete active space self-consistent-field (CASSCF) methods. The adiabatic ionization energies (AIEs) confirm the assignments as band I, one state 12B1 (12.671 eV); band II, three states, 12B2 (14.259) overlap. The apparent lack of a vibrational structure attributable to both the 12A1 and 22A1 states in the PES arises from line broadening with the preceding states 12B2 and 22B2, respectively. Although these 2A1 states clearly overlap with their adjacent higher IE, some vibrational structure is observed on the higher IE. The effects of vibronic coupling are evident since the observed structure does not fit closely with the calculated Born-Oppenheimer FC profiles. Correlation of the lowest group of four AIEs in the PES of other members of the CH2X2 group, where X = F, Cl, Br, and I, clearly indicate these effects are more general.

  1. Design of a ferrite rod antenna for harvesting energy from medium wave broadcast signals

    Directory of Open Access Journals (Sweden)

    Vladimir Dyo

    2013-12-01

    Full Text Available Radio frequency (RF energy harvesting is an emerging technology that has the potential to eliminate the need for batteries and reduce maintenance costs of sensing applications. The antenna is one of the critical components that determines its performance and while antenna design has been well researched for the purpose of communication, the design for RF energy harvesting applications has not been widely addressed. The authors present an optimised design for such an antenna for harvesting energy from medium wave broadcast transmissions. They derive and use a model for computing the optimal antenna configuration given application requirements on output voltage and power, material costs and physical dimensions. Design requirements for powering autonomous smart meters have been considered. The proposed approach was used to obtain the antenna configuration that is able to deliver 1 mW of power to 1 kΩ load at a distance of up to 9 km, sufficient to replace batteries on low-power sensing applications. Measurements using a prototype device have been used to verify the authors simulations.

  2. Change in design targets for building energy towards smart cities

    DEFF Research Database (Denmark)

    Heller, Alfred; Gianniou, Panagiota; Katsigiannis, Emmanouil

    2014-01-01

    Designing cities from an overall energy optimization system point of view, demands changes in engineering procedures. Traditionally the design was driven independently between the involved domains and energy system components. By modelling the whole energy system in one, it is expected that there......Designing cities from an overall energy optimization system point of view, demands changes in engineering procedures. Traditionally the design was driven independently between the involved domains and energy system components. By modelling the whole energy system in one, it is expected...... so is, to move demands from high demand periods to low demand periods and hereby to avoid “peak” demands. This is called “flexibility” within the terminology of “smart grids”. In early solutions the search was for energy capacities within the domain of the electrical grid, hence car batteries where...

  3. Application of a Decomposition Strategy to the Optimal Synthesis/Design and Operation of a Fuel Cell Based Total Energy System

    OpenAIRE

    2002-01-01

    A decomposition methodology based on the concept of â thermoeconomic isolationâ applied to the synthesis/design and operational optimization of a stationary cogeneration proton exchange membrane fuel cell (PEMFC) based total energy system (TES) for residential/commercial applications is the focus of this work. A number of different configurations for the fuel cell based TES were considered. The most promising set based on an energy integration analysis of candidate configurations was devel...

  4. Defining The Energy Saving Potential of Architectural Design

    DEFF Research Database (Denmark)

    Naboni, Emanuele; Malcangi, Antonio; Zhang, Yi

    2015-01-01

    Designers, in response to codes or voluntary " green building " programs, are increasingly concerned with building energy demand reduction, but they are not fully aware of the energy saving potential of architectural design. According to literature, building form, construction and material choices...... on sustainable design: " Design With Climate " by Olgyay (1963), which discussed strategies for climate-adapted architecture, and Lechner´s " Heating, Cooling and Lighting " (1991), on how to reduce building energy needs by as much as 60 – 80 percent with proper architectural design decisions. Both books used...... behaviour. The research shows the best solution for each of the climates and compares them with Olgyay´s findings. Finally, for each climate the energy saving potential is defined and then compared to Lechner's conclusions. Defining The Energy Saving Potential of Architectural Design (PDF Download Available...

  5. Measurement of the energy spectrum of cosmic rays with the 26 station configuration of the IceTop detector

    Energy Technology Data Exchange (ETDEWEB)

    Kislat, Fabian

    2011-09-27

    IceTop is an instrument at the geographic South Pole designed to detect cosmic ray air showers, particle cascades in the atmosphere initiated by high-energy cosmic rays. It is the surface component of the IceCube neutrino telescope. Since its completion in December 2010, IceTop consists of 81 detector stations covering an area of one square kilometer on the ice surface above IceCube. Each IceTop station consists of two ice-filled tanks in which the Cherenkov light emitted by charged air shower particles is measured. In this dissertation, an analysis of data taken in 2007 with 26 IceTop stations operational at that time is presented. First, properties of air showers like core position, direction and shower size were reconstructed from the measured signals. The core position can be determined to an accuracy of up to 6m and a direction resolution of up to 0.3 is achieved. The shower size is a measure of the energy of the primary particle and a resolution of up to 10% is achieved at high energies. In the next step the relation between primary energy and shower size, as well as resolution and efficiency are determined from Monte Carlo simulations of air showers and the IceTop detector. Here, an assumption was made about the chemical composition of cosmic rays. The informations obtained in these simulations are then used to unfold the spectrum of measured shower sizes in order to obtain the all-particle cosmic ray energy spectrum. This is done independently for particles from three different zenith angle intervals. The result of the unfolding depends on the assumed primary composition. Due to the isotropy of cosmic rays, results obtained in different zenith angle intervals must agree. While with the chosen analysis technique a simultaneous determination of primary particle mass and energy is limited due to systematic uncertainties, it has already been shown that the requirement of isotropy can be used to constrain the range of possible assumptions on the chemical

  6. Designing anthropological reflection within an energy company

    DEFF Research Database (Denmark)

    Løgstrup, Louise Buch; Gunn, Wendy; Said Mosleh, Wafa

    2013-01-01

    for a more bidirectional relationship between the company and their customers. During this process the company has realized that they lack knowledge about private energy end users. The company has run a demonstration project simulating the face of the electricity smart grid in private households and has used...... reflection is generated in the company through a flexible tangible scenario model of the bidirectional connection between the energy company and the users....

  7. Accuracy-Energy Configurable Sensor Processor and IoT Device for Long-Term Activity Monitoring in Rare-Event Sensing Applications

    Directory of Open Access Journals (Sweden)

    Daejin Park

    2014-01-01

    Full Text Available A specially designed sensor processor used as a main processor in IoT (internet-of-thing device for the rare-event sensing applications is proposed. The IoT device including the proposed sensor processor performs the event-driven sensor data processing based on an accuracy-energy configurable event-quantization in architectural level. The received sensor signal is converted into a sequence of atomic events, which is extracted by the signal-to-atomic-event generator (AEG. Using an event signal processing unit (EPU as an accelerator, the extracted atomic events are analyzed to build the final event. Instead of the sampled raw data transmission via internet, the proposed method delays the communication with a host system until a semantic pattern of the signal is identified as a final event. The proposed processor is implemented on a single chip, which is tightly coupled in bus connection level with a microcontroller using a 0.18 μm CMOS embedded-flash process. For experimental results, we evaluated the proposed sensor processor by using an IR- (infrared radio- based signal reflection and sensor signal acquisition system. We successfully demonstrated that the expected power consumption is in the range of 20% to 50% compared to the result of the basement in case of allowing 10% accuracy error.

  8. Accuracy-energy configurable sensor processor and IoT device for long-term activity monitoring in rare-event sensing applications.

    Science.gov (United States)

    Park, Daejin; Cho, Jeonghun

    2014-01-01

    A specially designed sensor processor used as a main processor in IoT (internet-of-thing) device for the rare-event sensing applications is proposed. The IoT device including the proposed sensor processor performs the event-driven sensor data processing based on an accuracy-energy configurable event-quantization in architectural level. The received sensor signal is converted into a sequence of atomic events, which is extracted by the signal-to-atomic-event generator (AEG). Using an event signal processing unit (EPU) as an accelerator, the extracted atomic events are analyzed to build the final event. Instead of the sampled raw data transmission via internet, the proposed method delays the communication with a host system until a semantic pattern of the signal is identified as a final event. The proposed processor is implemented on a single chip, which is tightly coupled in bus connection level with a microcontroller using a 0.18 μm CMOS embedded-flash process. For experimental results, we evaluated the proposed sensor processor by using an IR- (infrared radio-) based signal reflection and sensor signal acquisition system. We successfully demonstrated that the expected power consumption is in the range of 20% to 50% compared to the result of the basement in case of allowing 10% accuracy error.

  9. Implications of building energy standard for sustainable energy efficient design in buildings

    Energy Technology Data Exchange (ETDEWEB)

    Iwaro, Joseph; Mwasha, Abraham [University of West Indies, W. Department of Civil and Environmental Engineering, St. Augustine Campus (Trinidad and Tobago)

    2010-07-01

    The rapid growth of energy use, worldwide, has raised concerns over problems of energy supply, energy sustainability and exhaustion of energy resources. While most of the developed countries are implementing building energy standard rapidly to reduce building energy consumption and moving aggressively to achieve sustainable energy efficient building; the position of developing countries respect to energy standard implementation for this purpose is either poorly documented or not documented at all. Presently, there exists a gap between existing building designs and the increasing demand for sustainable energy efficient building design in developing countries. In that respect, this paper investigates the implementation status of building energy standards in developing countries and its implications for sustainable energy efficient designs in building. The present implementation status of building energy standard in 60 developing countries around the world, were analyzed using online survey. Hence, this study revealed the present implementation status of building energy standards in developing countries, implications for sustainable energy efficient designs in building and how building energy standards can be used to fill the gap between existing building designs and increasing demand for sustainable energy efficient building.

  10. Design of Bidirectional Check Valve for Discrete Fluid Power Force System for Wave Energy Converters

    DEFF Research Database (Denmark)

    Hansen, Anders Hedegaard; Pedersen, Henrik C.; Andersen, Torben Ole

    2014-01-01

    Discrete fluid power force systems consisting of a multichamber cylinder, a witching manifold and common pressure lines have been proposed as a technology for increasing the efficiency of the power take off system in ocean wave energy converters. However the force shifting of these discrete systems...... enables passive force switching under minimal pressure difference, hence minimal energy loss. The bidirectional check valve is designed with a rated flow in the range of 1000L/min@5bar. The flow direction of the bidirectional check valve is set by the setting the pilot pressure. This paper presents...... a functionality test of a 125 L/min@5bar bidirectional check, leading to the design and modelling of a bidirectional check valve for ocean wave energy. It shows that a feasible bidirectional check valve may be configured by employing a multi-poppet topology for the main stage and utilising a 3/2 switching valve...

  11. Method for optimal design of pipes for low-energy district heating, with focus on heat losses

    DEFF Research Database (Denmark)

    Dalla Rosa, Alessandro; Li, Hongwei; Svendsen, Svend

    2011-01-01

    The synergy between highly energy-efficient buildings and low-energy district heating (DH) systems is a promising concept for the optimal integration of energy-saving policies and energy supply systems based on renewable energy (RE). Network transmission and distribution heat loss is one of the key...... factors in the optimal design of low-energy DH systems. Various pipe configurations are considered in this paper: flexible pre-insulated twin pipes with symmetrical or asymmetrical insulation, double pipes, and triple pipes. These technologies represent potential energy-efficient and cost...... showed the influence of the soil temperature throughout the year. Finally, the article describes proposals for the optimal design of pipes for low-energy applications and presents methods for decreasing heat losses....

  12. On the energy gain enhancement of DT+D3He fuel configuration in nuclear fusion reactor driven by heavy ion beams

    Directory of Open Access Journals (Sweden)

    S Khoshbinfar

    2016-09-01

    Full Text Available It is expected that advanced fuels be employed in the second generation of nuclear fusion reactors. Theoretical calculations show that in such a fuel, a high plasma temperature about 100 keV is a requisite for reaction rate improvement of nuclear fusion. However, creating such a temporal condition requires a more powerful driver than we have today. Here, introducing an optimal fuel configuration consisting of DT and D-3He layers, suitable for inertial fusion reactors and driven by heavy ion beams, the optimal energy gain conditions have been simulated and derived for 1.3 MJ system. It was found that, in this new fuel configuration, the ideal energy gain, is 22 percent more comparing with energy gain in corresponding single DT fuel layer. Moreover, the inner DT fuel layer contributed as an ignition trigger, while the outer D3He fuel acts as particle and radiation shielding as well as fuel layer.

  13. PoE交换机设计与配置管理%Design and Configuration of PoE Switch

    Institute of Scientific and Technical Information of China (English)

    刘嘉滨

    2012-01-01

    在WLAN业务和安防网络视频监控业务中需部署大量无线AP和IP Camera设备,为解决部署在特殊位置上设备取电问题,可通过PoE技术进行远程供电.结合成熟的网络交换机技术,PoE交换机随之出现.通过介绍PoE交换机设计与配置,进一步加深对PoE技术的认识.这种设计和配置的PoE交换机已在市场上成功应用.%Lots of wireless AP and IP camera devices have to be deployed in WLAN and monitors. In order to provide power supply for devices in special positions, the Power over Ethernet technology can be utilized. In combination with the ripe switch technology, PoE switches appear. By introducing the design and configuration of the PoE switch, the PoE technology can be further understood. And this type of PoE switch has appeared in the market.

  14. Computational materials design for energy applications

    Science.gov (United States)

    Ozolins, Vidvuds

    2013-03-01

    General adoption of sustainable energy technologies depends on the discovery and development of new high-performance materials. For instance, waste heat recovery and electricity generation via the solar thermal route require bulk thermoelectrics with a high figure of merit (ZT) and thermal stability at high-temperatures. Energy recovery applications (e.g., regenerative braking) call for the development of rapidly chargeable systems for electrical energy storage, such as electrochemical supercapacitors. Similarly, use of hydrogen as vehicular fuel depends on the ability to store hydrogen at high volumetric and gravimetric densities, as well as on the ability to extract it at ambient temperatures at sufficiently rapid rates. We will discuss how first-principles computational methods based on quantum mechanics and statistical physics can drive the understanding, improvement and prediction of new energy materials. We will cover prediction and experimental verification of new earth-abundant thermoelectrics, transition metal oxides for electrochemical supercapacitors, and kinetics of mass transport in complex metal hydrides. Research has been supported by the US Department of Energy under grant Nos. DE-SC0001342, DE-SC0001054, DE-FG02-07ER46433, and DE-FC36-08GO18136.

  15. Error Mitigation in Computational Design of Sustainable Energy Materials

    DEFF Research Database (Denmark)

    Christensen, Rune

    functional theory calculations contribute in research and development of these technologies. Systematic errors are present in calculations with general gradient approximation functionals for all three technologies. Such functionals will in many cases be the best compromise of computational cost and accuracy...... networks. The method can validate the use of a neural network for emulation of density functional theory calculations for given atomic configuration....... be present in the OOH* adsorbate. However, the systematic error will almost be canceled by inclusion of van der Waals energy. The energy difference between key adsorbates is thus similar to that previously found. Finally, a method is developed for error estimation in computationally inexpensive neural...

  16. Designing a Portable and Low Cost Home Energy Management Toolkit

    NARCIS (Netherlands)

    Keyson, D.V.; Al Mahmud, A.; De Hoogh, M.; Luxen, R.

    2013-01-01

    In this paper we describe the design of a home energy and comfort management system. The system has three components such as a smart plug with a wireless module, a residential gateway and a mobile app. The combined system is called a home energy management and comfort toolkit. The design is inspired

  17. Design Concepts for Optimum Energy Use in HVAC Systems.

    Science.gov (United States)

    Electric Energy Association, New York, NY.

    Much of the innovative work in the design and application of heating, ventilating, and air conditioning (HVAC) systems is concentrated on improving the cost effectiveness of such systems through optimizing energy use. One approach to the problem is to reduce a building's HVAC energy demands by designing it for lower heat gains and losses in the…

  18. The power of design product innovation in sustainable energy technologies

    CERN Document Server

    Reinders, Angele H; Brezet, Han

    2012-01-01

    The Power of Design offers an introduction and a practical guide to product innovation, integrating the key topics that are necessary for the design of sustainable and energy-efficient products using sustainable energy technologies. Product innovation in sustainable energy technologies is an interdisciplinary field. In response to its growing importance and the need for an integrated view on the development of solutions, this text addresses the functional principles of various energy technologies next to the latest design processes and innovation methods. From the perspec

  19. Design Considerations of a Solid State Thermal Energy Storage

    Science.gov (United States)

    Janbozorgi, Mohammad; Houssainy, Sammy; Thacker, Ariana; Ip, Peggy; Ismail, Walid; Kavehpour, Pirouz

    2016-11-01

    With the growing governmental restrictions on carbon emission, renewable energies are becoming more prevalent. A reliable use of a renewable source however requires a built-in storage to overcome the inherent intermittent nature of the available energy. Thermal design of a solid state energy storage has been investigated for optimal performance. The impact of flow regime, laminar vs. turbulent, on the design and sizing of the system is also studied. The implications of low thermal conductivity of the storage material are discussed and a design that maximizes the round trip efficiency is presented. This study was supported by Award No. EPC-14-027 Granted by California Energy Commission (CEC).

  20. Parameter uncertainties in the design and optimization of cantilever piezoelectric energy harvesters

    Science.gov (United States)

    Franco, V. R.; Varoto, P. S.

    2017-09-01

    A crucial issue in piezoelectric energy harvesting is the efficiency of the mechanical to electrical conversion process. Several techniques have been investigated in order to obtain a set of optimum design parameters that will lead to the best performance of the harvester in terms of electrical power generation. Once an optimum design is reached it is also important to consider uncertainties in the selected parameters that in turn can lead to loss of performance in the energy conversion process. The main goal of this paper is to perform a comprehensive discussion of the effects of multi-parameter aleatory uncertainties on the performance and design optimization of a given energy harvesting system. For that, a typical energy harvester consisting of a cantilever beam carrying a tip mass and partially covered by piezoelectric layers on top and bottom surfaces is considered. A distributed parameter electromechanical modal of the harvesting system is formulated and validated through experimental tests. First, the SQP (Sequential Quadratic Planning) optimization is employed to obtain an optimum set of parameters that will lead to best performance of the harvester. Second, once the optimum harvester configuration is found random perturbations are introduced in the key parameters and Monte Carlo simulations are performed to investigate how these uncertainties propagate and affect the performance of the device studied. Numerically simulated results indicate that small variations in some design parameters can cause a significant variation in the output electrical power, what strongly suggests that uncertainties must be accounted for in the design of beam energy harvesting systems.

  1. Satellite Formation Configuration Design Visible System%卫星编队构型设计可视化系统

    Institute of Scientific and Technical Information of China (English)

    王传魁; 董云峰; 邓武东; 苏建敏

    2012-01-01

    In order to design satellite formation through nature way, a 3D display configuration scenario was established by using OSG (Open Scene Graph) technology. The usage of virtual reality makes designation process visible, and realizes man-machine interface under virtual environment. Transfer platform based on HLA protocol ensures communication among applications. With the usage of speech recognition, data glove, image recognition and other human-computer interface, new system avoids to be as boring as common keyboard-mouse-interface does, and meets various requirements of them.%为实现更自然的卫星编队构型设计,采用OSG(Open Scene Graph)技术建立了卫星编队飞行轨道构型设计过程三维显示场景。虚拟现实技术使抽象的理论设计可视化,实现了虚拟环境下的人机对话。基于HLA(High Level Architecture)下的RTI(Run Time Infrastructure)通讯协议平台,确保了交互通讯的流畅性。采用语音识别、数据手套、图像识别等多种人机交互模式,解决了鼠标键盘操作的枯燥性,让使用者产生沉浸感,满足了不同使用者的操作要求,降低工作人员的疲倦感。

  2. Design configurations affecting flow pattern and solids accumulation in horizontal free water and subsurface flow constructed wetlands.

    Science.gov (United States)

    Pedescoll, A; Sidrach-Cardona, R; Sánchez, J C; Carretero, J; Garfi, M; Bécares, E

    2013-03-01

    The aim of this study was to evaluate the effect of different horizontal constructed wetland (CW) design parameters on solids distribution, loss of hydraulic conductivity over time and hydraulic behaviour, in order to assess clogging processes in wetlands. For this purpose, an experimental plant with eight CWs was built at mesocosm scale. Each CW presented a different design characteristic, and the most common CW configurations were all represented: free water surface flow (FWS) with different effluent pipe locations, FWS with floating macrophytes and subsurface flow (SSF), and the presence of plants and specific species (Typha angustifolia and Phragmites australis) was also considered. The loss of the hydraulic conductivity of gravel was greatly influenced by the presence of plants and organic load (representing a loss of 20% and c.a. 10% in planted wetlands and an overloaded system, respectively). Cattail seems to have a greater effect on the development of clogging since its below-ground biomass weighed twice as much as that of common reed. Hydraulic behaviour was greatly influenced by the presence of a gravel matrix and the outlet pipe position. In strict SSF CW, the water was forced to cross the gravel and tended to flow diagonally from the top inlet to the bottom outlet (where the inlet and outlet pipes were located). However, when FWS was considered, water preferentially flowed above the gravel, thus losing half the effective volume of the system. Only the presence of plants seemed to help the water flow partially within the gravel matrix. Copyright © 2012 Elsevier Ltd. All rights reserved.

  3. Design of Energy Efficient Hybrid Ventilation

    DEFF Research Database (Denmark)

    Heiselberg, Per

    The focus in the development has for both systems been to minimise energy consumption while maintaining a comfortable and healthy indoor environment. The natural next step in this development is to develop ventilation concepts that utilises and combines the best features from each system[Mechanic......The focus in the development has for both systems been to minimise energy consumption while maintaining a comfortable and healthy indoor environment. The natural next step in this development is to develop ventilation concepts that utilises and combines the best features from each system...

  4. Comparison between four dissimilar solar panel configurations

    Science.gov (United States)

    Suleiman, K.; Ali, U. A.; Yusuf, Ibrahim; Koko, A. D.; Bala, S. I.

    2017-03-01

    Several studies on photovoltaic systems focused on how it operates and energy required in operating it. Little attention is paid on its configurations, modeling of mean time to system failure, availability, cost benefit and comparisons of parallel and series-parallel designs. In this research work, four system configurations were studied. Configuration I consists of two sub-components arranged in parallel with 24 V each, configuration II consists of four sub-components arranged logically in parallel with 12 V each, configuration III consists of four sub-components arranged in series-parallel with 8 V each, and configuration IV has six sub-components with 6 V each arranged in series-parallel. Comparative analysis was made using Chapman Kolmogorov's method. The derivation for explicit expression of mean time to system failure, steady state availability and cost benefit analysis were performed, based on the comparison. Ranking method was used to determine the optimal configuration of the systems. The results of analytical and numerical solutions of system availability and mean time to system failure were determined and it was found that configuration I is the optimal configuration.

  5. Three Principles for the Design of Energy Feedback Visualizations

    DEFF Research Database (Denmark)

    Brewer, Robert S.; Xu, Yongwen; Lee, George E.

    2013-01-01

    To achieve the full benefits of the Smart Grid, end users must become active participants in the energy ecosystem. This paper presents the Kukui Cup challenge, a multifaceted serious game designed around the topic of energy conservation that incorporates a variety of energy feedback visualization...

  6. Minimum energy design using grassed spillways

    Energy Technology Data Exchange (ETDEWEB)

    Lewis, B. [FIE Aust, Melbourne (Australia)

    2004-09-01

    Small dams for rural communities in Australia often fail due to the Spillway or bywash, because it receives insufficient attention during the design, construction and maintenance processes. More thorough investigation and improved standards of design and construction are needed in order to resolve problems. This paper described some of the reasons for adopting grass spillways on farm dams. It compared grass and earth spillways and also discussed spillway design factors such as site conditions, peak flow estimation, and design spillway size. The factors affecting selection of spillway type and design include safety requirements, hydrological conditions, geological and site topographical conditions, and type of dam. Factors involved in grass selection in spillway design were also identified. These include climate, soils, land systems, and quality and duration of discharge, growth characteristics, hydraulic behaviour, and maintenance. It was concluded that additional research is needed regarding methods of establishing grass cover to inlets and outlet spillway. In particular, there is a need to evaluate the growth of grasses through plastic meshes and geotextiles, which could provide protection against erosion while the grass is becoming established. 10 refs., 4 tabs.

  7. Developing an energy design tool: Phase 1 report

    Energy Technology Data Exchange (ETDEWEB)

    Heidell, J.A.; Deringer, J.D.

    1987-02-01

    This report documents the planning phase of a proposed four-phase project for creating computer software to provide energy expertise in a manageable form to architects and engineers - thereby decreasing energy use in new buildings. The government sponsored software would be integrated with commercially developed software for use in the design of buildings. The result would be an integrated software package to aid the designer in the building design process and to provide expert insight into the energy related implications of a proposed design.

  8. Dynamic behavior of the intensified alternative configurations for quaternary distillation

    DEFF Research Database (Denmark)

    Ramirez-Marquez, Cesar; Cabrera-Ruiz, Julián; Juan Gabriel Segovia-Hernandez, Juan Gabriel;

    2016-01-01

    Process intensification emerges as an important tool in the synthesis of multicomponent distillation configurations aimed at the reduction of the energy use and capital costs. Operational and fixed costs savings coupled with simplicity and controllability design configurations appear as an essent...

  9. The design of Smart Energy Systems for 100% renewable energy and transport solutions

    DEFF Research Database (Denmark)

    Mathiesen, Brian Vad; Lund, Henrik; Connolly, David

    2013-01-01

    In this paper we launch the design of Smart Energy Systems through the 100% renewable energy system analyses and research behind the CEESA research project. The transition from fossil fuels towards the integration of more and more renewable energy requires rethinking and redesign of the energy...

  10. Conceptual design of cost-effective and environmentally-friendly configurations for fuel ethanol production from sugarcane by knowledge-based process synthesis.

    Science.gov (United States)

    Sánchez, Óscar J; Cardona, Carlos A

    2012-01-01

    In this work, the hierarchical decomposition methodology was used to conceptually design the production of fuel ethanol from sugarcane. The decomposition of the process into six levels of analysis was carried out. Several options of technological configurations were assessed in each level considering economic and environmental criteria. The most promising alternatives were chosen rejecting the ones with a least favorable performance. Aspen Plus was employed for simulation of each one of the technological configurations studied. Aspen Icarus was used for economic evaluation of each configuration, and WAR algorithm was utilized for calculation of the environmental criterion. The results obtained showed that the most suitable synthesized flowsheet involves the continuous cultivation of Zymomonas mobilis with cane juice as substrate and including cell recycling and the ethanol dehydration by molecular sieves. The proposed strategy demonstrated to be a powerful tool for conceptual design of biotechnological processes considering both techno-economic and environmental indicators.

  11. Business Model Process Configurations

    DEFF Research Database (Denmark)

    Taran, Yariv; Nielsen, Christian; Thomsen, Peter

    2015-01-01

    Purpose – The paper aims: 1) To develop systematically a structural list of various business model process configuration and to group (deductively) these selected configurations in a structured typological categorization list. 2) To facilitate companies in the process of BM innovation......, by developing (inductively) an ontological classification framework, in view of the BM process configurations typology developed. Design/methodology/approach – Given the inconsistencies found in the business model studies (e.g. definitions, configurations, classifications) we adopted the analytical induction...... method of data analysis. Findings - A comprehensive literature review and analysis resulted in a list of business model process configurations systematically organized under five classification groups, namely, revenue model; value proposition; value configuration; target customers, and strategic...

  12. Requirements of Integrated Design Teams While Evaluating Advanced Energy Retrofit Design Options in Immersive Virtual Environments

    Directory of Open Access Journals (Sweden)

    Xue Yang

    2015-12-01

    Full Text Available One of the significant ways to save energy use in buildings is to implement advanced energy retrofits in existing buildings. Improving energy performance of buildings through advanced energy retrofitting requires a clear understanding of the cost and energy implications of design alternatives from various engineering disciplines when different retrofit options are considered. The communication of retrofit design alternatives and their energy implications is essential in the decision-making process, as it affects the final retrofit selections and hence the energy efficiency of the retrofitted buildings. The objective of the research presented here was to identify a generic list of information requirements that are needed to be shared and collectively analyzed by integrated design teams during advanced energy retrofit design review meetings held in immersive settings. While identifying such requirements, the authors used an immersive environment based iterative requirements elicitation approach. The technology was used as a means to better identify the information requirements of integrated design teams to be analyzed as a group. This paper provides findings on information requirements of integrated design teams when evaluating retrofit options in immersive virtual environments. The information requirements were identified through interactions with sixteen experts in design and energy modeling domain, and validated with another group of participants consisting of six design experts who were experienced in integrated design processes. Industry practitioners can use the findings in deciding on what information to share with integrated design team members during design review meetings that utilize immersive virtual environments.

  13. Integrated design means energy economy for life

    Energy Technology Data Exchange (ETDEWEB)

    Bugden, J.

    1983-03-25

    The architecture, and the electrical and air conditioning services of the 13,000 m/sup 2/ seven story open plan office in Bristol, UK, have been completely integrated to give a highly energy-efficient building. The principle of the all-embracing environmental control system is that of redistribution of excess heat produced in the centre of a deep plan building. The excess comes from lighting, machines and personnel body heat and is transferred by air ducts to cooler areas, mostly at the perimeter. The central monitoring and control of the services is by a Visonek 4000 building automations system operating from the basement plant room. An energy flow diagram is provided.

  14. Design and management of energy-efficient hybrid electrical energy storage systems

    CERN Document Server

    Kim, Younghyun

    2014-01-01

    This book covers system-level design optimization and implementation of hybrid energy storage systems. The author introduces various techniques to improve the performance of hybrid energy storage systems, in the context of design optimization and automation. Various energy storage techniques are discussed, each with its own advantages and drawbacks, offering viable, hybrid approaches to building a high performance, low cost energy storage system. Novel design optimization techniques and energy-efficient operation schemes are introduced. The author also describes the technical details of an act

  15. Aircraft energy efficiency laminar flow control wing design study

    Science.gov (United States)

    Bonner, T. F., Jr.; Pride, J. D., Jr.; Fernald, W. W.

    1977-01-01

    An engineering design study was performed in which laminar flow control (LFC) was integrated into the wing of a commercial passenger transport aircraft. A baseline aircraft configuration was selected and the wing geometry was defined. The LFC system, with suction slots, ducting, and suction pumps was integrated with the wing structure. The use of standard aluminum technology and advanced superplastic formed diffusion bonded titanium technology was evaluated. The results of the design study show that the LFC system can be integrated with the wing structure to provide a structurally and aerodynamically efficient wing for a commercial transport aircraft.

  16. ZEUS-DO: A Design Oriented CFD-Based Unsteady Aerodynamic Capability for Flight Vehicle Multidisciplinary Configuration Shape Optimization Project

    Data.gov (United States)

    National Aeronautics and Space Administration — In practically all air-vehicle MDO studies to date involving configuration shape optimization, dynamic Aeroservoelastic constraints had to be left out. Flutter, gust...

  17. A New Method of Technical Analysis to Optimise the Design of Low Impact Energy Systems for Buildings

    Directory of Open Access Journals (Sweden)

    Roberto De Lieto Vollaro

    2013-10-01

    Full Text Available Energy consumption for civil constructions represents about 40% of total energy requirements, so it is necessary to achieve the goal of energy savings and the consequent reduction of greenhouse gases emissions. The study in content aims to provide a design methodology enables to identify the best plant configuration for buildings from a technical, economic and environmental point of view. To assess validity of the calculation model, an analysis of an historical building was carried out in combination with two softwares of proven reliability: TRNSYS, used to evaluate the thermal demand of users, and RETScreen, used to estimate the validity of the chosen energy model.

  18. Effect of nitrite, limited reactive settler and plant design configuration on the predicted performance of simultaneous C/N/P removal WWTPs

    DEFF Research Database (Denmark)

    Guerrero, Javier; Flores-Alsina, Xavier; Guisasola, Albert

    2013-01-01

    This paper describes a modelling study where five new benchmark plant design configurations for biological nutrient removal (A2/O, UCT, JHB, MUCT and BDP-5 stage) are simulated and evaluated under different model assumptions. The ASM2d including electron dependent decay rates is used as the refer...

  19. Design of a digital interactive configuration, flexible and inexpensive, for monitoring the movements of people in real time

    Directory of Open Access Journals (Sweden)

    Enrico Costa

    2014-12-01

    Full Text Available We aim to introduce here the idea and the first results of a still ongoing research regarding the setup of a flexible and inexpensive digital interactive configuration, which has the goal of tracking the position and routes of a certain amount of subjects inside a medium or large closed space. The configuration appears to be adequate especially for the monitoring of museums spaces, exhibitions and showrooms.

  20. The application of design criteria for locating a hub configured supply chain for a restaurant cluster in the Stellenbosch area

    Directory of Open Access Journals (Sweden)

    Claudia B. Struwig

    2013-05-01

    Full Text Available Restaurants, in general, utilise numerous suppliers. Normally they deliver on different days in the week and at different times during the day, logistically not an optimum approach. Not only does the current practice cause frequent interruptions, but by segregating the food supply chain unnecessary traffic is generated. This article investigated the need for developing a third party supplier hub, the best positioning of that hub and the most economical routes to the customers. With the aim of providing non-franchised restaurants with the necessary leverage to become market leaders, the hub is planned to only service the restaurants within the vicinity of the Stellenbosch area. In such a hub-configured supply chain, the suppliers would be delivering to the proposed hub, from where once-off deliveries to all the restaurants may be made on days and/or times determined by them. In order to investigate the benefits of providing such a hub structure, a systematic implementation approach was used. The first step was to do market research in order to establish the need for such a hub. That is, the viability of the hub from a restaurant’s perspective was established. The next step entailed the investigation of the design criteria needed in determining a favourable hub location. Four possible hub locations were identified. The Clark and Wright’s savings algorithm was then used to determine the optimal hub location and the feasibility of the results was verified with the aid of a global positioning system (GPS device. The last steps followed involved the determination of an effective hub floor plan that may be utilised, possible products that can be supplied to the restaurants and the necessary assets needed to provide the hub’s service. Finally, by incorporating all these facets, a cost analysis was done to determine the hub’s profitability.

  1. Design considerations for energy efficient, resilient, multi-layer networks

    DEFF Research Database (Denmark)

    Fagertun, Anna Manolova; Hansen, Line Pyndt; Ruepp, Sarah Renée

    2016-01-01

    This work investigates different network design considerations with respect to energy-efficiency, under green-field resilient multi-layer network deployment. The problem of energy efficient, reliable multi-layer network design is known to result in different trade-offs between key performance...... in multi-layer networks and performance measures such as network resource utilization, availability, agility to traffic fluctuations and energy consumption. A green-field network deployment scenario is considered, where different resiliency methods, design methodologies and grooming strategies are applied...

  2. Modelling, design, and optimization of net-zero energy buildings

    CERN Document Server

    Athienitis, Andreas

    2015-01-01

    Building energy design is currently going through a period of major changes. One key factor of this is the adoption of net-zero energy as a long term goal for new buildings in most developed countries. To achieve this goal a lot of research is needed to accumulate knowledge and to utilize it in practical applications. In this book, accomplished international experts present advanced modeling techniques as well as in-depth case studies in order to aid designers in optimally using simulation tools for net-zero energy building design. The strategies and technologies discussed in this book are, ho

  3. Conceptual design of the 3D magnetic field configuration relevant to the magnetopause reconnection in the SPERF

    Science.gov (United States)

    Mao, Aohua; Ji, Hantao; Ren, Yang; E, Peng; Wang, Zhibin; Xiao, Qingmei; Xiao, Chijie

    2016-10-01

    A new terrella device, the Space Plasma Environment Research Facility (SPERF), is designed and under construction in China, with Asymmetric Reconnection EXperiment (AREX) as one component to study the interaction between the magnetosheath and magnetosphere plasmas. AREX will provide a unique platform for studying asymmetric magnetic reconnection relevant to the magnetopause, via a set of coils for simulating ``solar-wind-side'' magnetosheath field and a dipole field on the ``magnetosphere-side''. Thus it could be able to investigate a range of important issues in the magnetosphere geometry, such as the electron and ion-scale dynamics in the current sheet, particle and energy transfer from magnetosheath to magnetosphere, particle energization/heating during magnetic reconnection, 3D and asymmetric effects in fast reconnection, and so on. The plasma is generated by two flux cores at the ``magnetosheath-side'' and one electron cyclotron resonance source at the ``magnetosphere-side''. Different kinds of coils with specific current driven functions, as well as advanced diagnostics are designed. Motivation, overview of the AREX design and reconnection scenarios will be discussed.

  4. Integrated Design for Marketing and Manufacturing team: An examination of LA-ICP-AES in a mobile configuration. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1994-05-01

    The Department of Energy (DOE) has identified the need for field-deployable elemental analysis devices that are safer, faster, and less expensive than the fixed laboratory procedures now used to screen hazardous waste sites. As a response to this need, the Technology Integration Program (TIP) created a mobile, field-deployable laser ablation-inductively coupled plasma-atomic emission spectrometry (LA-ICP-AES) sampling and analysis prototype. Although the elemental. screening prototype has been successfully field-tested, continued marketing and technical development efforts are required to transfer LA-ICP-AES technology to the commercial sector. TIP established and supported a student research and design group called the Integrated Design for Marketing and Manufacturing (IDMM) team to advance the technology transfer of mobile, field-deployable LA-ICP-AES. The IDMM team developed a conceptual design (which is detailed in this report) for a mobile, field-deployable LA-ICP-AES sampling and analysis system, and reports the following findings: Mobile, field-deployable LA-ICP-AES is commercially viable. Eventual regulatory acceptance of field-deployable LA-ICP-AES, while not a simple process, is likely. Further refinement of certain processes and components of LA-ICP-AES will enhance the device`s sensitivity and accuracy.

  5. Optimization under Uncertainty of Site-Specific Turbine Configurations: Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Quick, Julian; Dykes, Katherine; Graf, Peter; Zahle, Frederik

    2016-11-01

    Uncertainty affects many aspects of wind energy plant performance and cost. In this study, we explore opportunities for site-specific turbine configuration optimization that accounts for uncertainty in the wind resource. As a demonstration, a simple empirical model for wind plant cost of energy is used in an optimization under uncertainty to examine how different risk appetites affect the optimal selection of a turbine configuration for sites of different wind resource profiles. If there is unusually high uncertainty in the site wind resource, the optimal turbine configuration diverges from the deterministic case and a generally more conservative design is obtained with increasing risk aversion on the part of the designer.

  6. Integrated design by optimization of electrical energy systems

    CERN Document Server

    Roboam, Xavier

    2013-01-01

    This book proposes systemic design methodologies applied to electrical energy systems, in particular integrated optimal design with modeling and optimization methods and tools. It is made up of six chapters dedicated to integrated optimal design. First, the signal processing of mission profiles and system environment variables are discussed. Then, optimization-oriented analytical models, methods and tools (design frameworks) are proposed. A "multi-level optimization" smartly coupling several optimization processes is the subject of one chapter. Finally, a technico-economic optimizatio

  7. Design of Energy Storage Reactors for Dc-To-Dc Converters. Ph.D. Thesis

    Science.gov (United States)

    Chen, D. Y.

    1975-01-01

    Two methodical approaches to the design of energy-storage reactors for a group of widely used dc-to-dc converters are presented. One of these approaches is based on a steady-state time-domain analysis of piecewise-linearized circuit models of the converters, while the other approach is based on an analysis of the same circuit models, but from an energy point of view. The design procedure developed from the first approach includes a search through a stored data file of magnetic core characteristics and results in a list of usable reactor designs which meet a particular converter's requirements. Because of the complexity of this procedure, a digital computer usually is used to implement the design algorithm. The second approach, based on a study of the storage and transfer of energy in the magnetic reactors, leads to a straightforward design procedure which can be implemented with hand calculations. An equation to determine the lower-bound volume of workable cores for given converter design specifications is derived. Using this computer lower-bound volume, a comparative evaluation of various converter configurations is presented.

  8. Ocean Thermal Energy Conversion power system development. Phase I: preliminary design. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1978-12-04

    Westinghouse has completed the Preliminary Desigh Phase for the Power System Development of the Ocean Thermal Energy Conversion (OTEC) Demonstration Plant project. This study included the development of a preliminary design for a Modular Application scaled power system (10MWe) and Heat Exchanger Test Articles, both based on the concept developed in the Conceptual Design Phase. The results of this study were used to improve the baseline design of the 50MWe module for the Commercial Size Power System, which was recommended for the demonstration plant by the conceptual design study. The 50MWe module was selected since it has the lowest cost, and since its size convincingly demonstrates that future economically viable commercial plants, having reliable operation with credible anticipated costs, are possible. Additional optimization studies on the size of the power system plus hull continue to identify 50MWe as the preferred minimum cost configuration. This study was limited to a closed cycle ammonia power system module, using a seawater temperature difference of 40/sup 0/F, and a surface platform/ship reference hull. This volume presents the preliminary design configuration and system optimization. (WHK)

  9. Energy Analysis of a Student-Designed Solar House

    Directory of Open Access Journals (Sweden)

    Samantha Wermager

    2013-12-01

    Full Text Available This paper presents the findings from an undergraduate research project concerning the energy efficiency, consumption, and generation of a 1000 ft2 (92.9 m2 solar house. The results were compared to a home of similar size and layout, built using traditional construction methods. The solar house was modeled after the Chameleon House: Missouri University of Science and Technology’s 2013 entry in the U.S. Department of Energy Solar Decathlon. The efficiency of the design was analyzed using Energy-10 Version 1.8 software. For this comparison, a fictional American couple was created and a breakdown of their energy-use habits was recorded to accurately depict the magnitude of energy consumption. A 71% energy savings was forecasted using the Energy-10 software through the incorporation of various energy-conserving strategies in the home’s design. In addition, if a 9.1 kW photovoltaic array is also installed on a home of this size, it is possible to fully offset the energy consumption of the home. The forecasted energy usage and production detailed in this report shall be used for analyzing the integrity of the design of the Chameleon House as well as future solar houses constructed by the Missouri S&T Solar House Team.

  10. Energy Design Plugin: An EnergyPlus Plugin for SketchUp; Preprint

    Energy Technology Data Exchange (ETDEWEB)

    Ellis, P. G.; Torcellini, P. A.; Crawley, D. B.

    2008-08-01

    This paper describes the Energy Design Plugin, a new software plugin that aims to integrate simulation as a tool during the earliest phases of the design process. The plugin couples the EnergyPlus whole-building simulation engine to the Google SketchUp drawing program.

  11. Electric grid stability and the design of sustainable energy systems

    DEFF Research Database (Denmark)

    Lund, Henrik

    2005-01-01

    The article presents technical designs of potential future flexible energy systems, which will be able both to balance production and demand and to secure voltage and frequency requirements on the grid....

  12. Design of System Architecture and Thermal Management Components for an Underwater Energy Storage Facility

    Science.gov (United States)

    Cheung, Brian C.

    The electricity industry is currently experiencing a significant paradigm shift in managing electrical resources. With the onset of aging infrastructure and growing power demands, and the influx of intermittent renewable energy generation, grid system operators are looking towards energy storage as a solution for mitigating industry challenges. An emerging storage solution is underwater compressed air energy storage (UWCAES), where air compressors and turbo-expanders are used to convert electricity to and from compressed air stored in submerged accumulators. This work presents three papers that collectively focus on the design and optimization of an UWCAES system. In the first paper, the field performance of a distensible air accumulator is studied for application in UWCAES systems. It is followed by a paper that analyzed the energetic and exergetic performance of a theoretical UWCAES system. The final paper presents a multi-objective UWCAES optimization model utilizing a genetic algorithm to determine optimum system configurations.

  13. Total energy control system autopilot design with constrained parameter optimization

    Science.gov (United States)

    Ly, Uy-Loi; Voth, Christopher

    1990-01-01

    A description is given of the application of a multivariable control design method (SANDY) based on constrained parameter optimization to the design of a multiloop aircraft flight control system. Specifically, the design method is applied to the direct synthesis of a multiloop AFCS inner-loop feedback control system based on total energy control system (TECS) principles. The design procedure offers a structured approach for the determination of a set of stabilizing controller design gains that meet design specifications in closed-loop stability, command tracking performance, disturbance rejection, and limits on control activities. The approach can be extended to a broader class of multiloop flight control systems. Direct tradeoffs between many real design goals are rendered systematic by proper formulation of the design objectives and constraints. Satisfactory designs are usually obtained in few iterations. Performance characteristics of the optimized TECS design have been improved, particularly in the areas of closed-loop damping and control activity in the presence of turbulence.

  14. Ionic Liquids in Polymer Design: From Energy to Health

    Science.gov (United States)

    2016-10-19

    SECURITY CLASSIFICATION OF: ACS Symposium: Ionic Liquids in Polymer Design: From Energy to Health at Fall 2015 ACS Meeting in Boston, MA The...combination of ionic liquids and polymers has emerged as an active field of exploration in polymer science, where new materials have be realized for...2016 Final Report: Ionic Liquids in Polymer Design: From Energy to Health The views, opinions and/or findings contained in this report are those of

  15. A design guide for energy-efficient research laboratories

    Energy Technology Data Exchange (ETDEWEB)

    Wishner, N.; Chen, A.; Cook, L. [eds.; Bell, G.C.; Mills, E.; Sartor, D.; Avery, D.; Siminovitch, M.; Piette, M.A.

    1996-09-24

    This document--A Design Guide for Energy-Efficient Research Laboratories--provides a detailed and holistic framework to assist designers and energy managers in identifying and applying advanced energy-efficiency features in laboratory-type environments. The Guide fills an important void in the general literature and compliments existing in-depth technical manuals. Considerable information is available pertaining to overall laboratory design issues, but no single document focuses comprehensively on energy issues in these highly specialized environments. Furthermore, practitioners may utilize many antiquated rules of thumb, which often inadvertently cause energy inefficiency. The Guide helps its user to: introduce energy decision-making into the earliest phases of the design process, access the literature of pertinent issues, and become aware of debates and issues on related topics. The Guide does focus on individual technologies, as well as control systems, and important operational factors such as building commissioning. However, most importantly, the Guide is intended to foster a systems perspective (e.g. right sizing) and to present current leading-edge, energy-efficient design practices and principles.

  16. Building Design Guidelines for Solar Energy Technologies

    Science.gov (United States)

    Givoni, B.

    1989-01-01

    There are two main objectives to this publication. The first is to find out the communalities in the experience gained in previous studies and in actual applications of solar technologies in buildings, residential as well as nonresidential. The second objective is to review innovative concepts and products which may have an impact on future developments and applications of solar technologies in buildings. The available information and common lessons were collated and presented in a form which, hopefully, is useful for architects and solar engineers, as well as for teachers of "solar architecture" and students in Architectural Schools. The publication is based mainly on the collection and analysis of relevant information. The information included previous studies in which the performance of solar buildings was evaluated, as well as the personal experience of the Author and the research consultants. The state of the art, as indicated by these studies and personal experience, was summarized and has served as basis for the development of the Design Guidelines. In addition to the summary of the state of the art, as was already applied in solar buildings, an account was given of innovative concepts and products. Such innovations have occurred in the areas of thermal storage by Phase Change Materials (PCM) and in glazing with specialized or changeable properties. Interesting concepts were also developed for light transfer, which may enable to transfer sunlight to the core areas of large multi story nonresidential buildings. These innovations may have a significant impact on future developments of solar technologies and their applications in buildings.

  17. Implications of solar energy alternatives for community design

    Energy Technology Data Exchange (ETDEWEB)

    Santos, A.; Steinitz, C.

    1980-06-01

    A graduate-level studio at the Harvard School of Design explored how a policy of solar-based energy independence will influence the design of a new community of approximately 4500 housing units and other uses. Three large sites outside Tucson (a cooling problem), Atlanta (a humidity problem), and Boston (a heating problem) were selected. Each is typical of its region. A single program was assumed and designed for. Each site had two teams, one following a compact approach and one following a more dispersed approach. Each was free to choose the most appropriate mix of (solar) technology and scale, and was free to integrate energy and community in the design as it saw fit. These choice and integration issues are key areas where our experience may be of interest to those involved in community design and solar energy.

  18. An Integrated Refurbishment Design Process to Energy Efficiency

    NARCIS (Netherlands)

    Konstantinou, T.; Knaack, U.

    2013-01-01

    Given the very low renewal rate of the building stock, the efforts to reduce energy demand must focus on the existing residential buildings. Even though awareness has been raised, the effect on energy efficiency is often neglected during the design phase of refurbishment projects. This paper discuss

  19. Junction Temperature Aware Energy Efficient Router Design on FPGA

    DEFF Research Database (Denmark)

    Thind, Vandana; Sharma, Shivani; Minwer, M H

    2015-01-01

    Energy, Power and efficiency are very much related to each other. To make any system efficient, Power consumed by it must be minimized or we can say that power dissipation should be less. In our research we tried to make a energy efficient router design on FPGA by varying junction temperature...

  20. Modeling and design of energy efficient variable stiffness actuators

    NARCIS (Netherlands)

    Visser, L.C.; Carloni, Raffaella; Ünal, Ramazan; Stramigioli, Stefano

    In this paper, we provide a port-based mathematical framework for analyzing and modeling variable stiffness actuators. The framework provides important insights in the energy requirements and, therefore, it is an important tool for the design of energy efficient variable stiffness actuators. Based

  1. Design optimization of PVDF-based piezoelectric energy harvesters.

    Science.gov (United States)

    Song, Jundong; Zhao, Guanxing; Li, Bo; Wang, Jin

    2017-09-01

    Energy harvesting is a promising technology that powers the electronic devices via scavenging the ambient energy. Piezoelectric energy harvesters have attracted considerable interest for their high conversion efficiency and easy fabrication in minimized sensors and transducers. To improve the output capability of energy harvesters, properties of piezoelectric materials is an influential factor, but the potential of the material is less likely to be fully exploited without an optimized configuration. In this paper, an optimization strategy for PVDF-based cantilever-type energy harvesters is proposed to achieve the highest output power density with the given frequency and acceleration of the vibration source. It is shown that the maximum power output density only depends on the maximum allowable stress of the beam and the working frequency of the device, and these two factors can be obtained by adjusting the geometry of piezoelectric layers. The strategy is validated by coupled finite-element-circuit simulation and a practical device. The fabricated device within a volume of 13.1 mm(3) shows an output power of 112.8 μW which is comparable to that of the best-performing piezoceramic-based energy harvesters within the similar volume reported so far.

  2. Building design guidelines for solar energy technologies

    Energy Technology Data Exchange (ETDEWEB)

    Givoni, B.

    1989-01-01

    There are two main objectives to this publication. The first is to find out the communalities in the experience gained in previous studies and in actual applications of solar technologies in buildings, residential as well as nonresidential. The second objective is to review innovative concepts and products which may have an impact on future developments and applications of solar technologies in buildings. The available information and common lessons were collated and presented in a form which, hopefully, is useful for architects and solar engineers, as well as for teachers of solar architecture'' and students in Architectural Schools. The publication is based mainly on the collection and analysis of relevant information. The information included previous studies in which the performance of solar buildings was evaluated, as well as the personal experience of the Author and the research consultants. The state of the art, as indicated by these studies and personal experience, was summarized and has served as basis for the development of the Design Guidelines. In addition to the summary of the state of the art, as was already applied in solar buildings, an account was given of innovative concepts and products. Such innovations have occurred in the areas of thermal storage by Phase Change Materials (PCM) and in glazing with specialized or changeable properties. Interesting concepts were also developed for light transfer, which may enable to transfer sunlight to the core areas of large multi story nonresidential buildings. These innovations may have a significant impact on future developments of solar technologies and their applications in buildings. 15 refs., 19 figs., 3 tabs.

  3. Design Features of Regional Energy Reactor, REX-10

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Jong Won; Lee, Yeon Gun; Lim, Sung Won; Park, Goon Cherl [Seoul National Univ., Seoul (Korea, Republic of); Joo, Hyeong Min; Jang, Byeong Il [Hanyang Univ., Seoul (Korea, Republic of); Kim, Moo Hwan [POSTECH, Pohang (Korea, Republic of)

    2009-05-15

    Recently, today's global pattern of energy supply is not sustainable. The provision of affordable energy services is a fundamental prerequisite for economic growth and development. In addition, the environmental problems such as energy crisis, global warming and acid rain are issued and more demand for reliable electricity supply increases. As one of the realistic solutions, the extension of the peaceful uses of nuclear energy has been suggested. Small and medium nuclear reactors with non-electric applications arise as an alternative energy source. The main non-electric applications are defined as district heating, desalination (of sea, brackish and waste water), industrial heat supply, ship propulsion and the energy supply for spacecraft. RERI (Regional Energy Research Institute for the Next Generation) is to develop a small-scale electric power system by an environmentally-friendly and stable small nuclear reactor. The newly designed REX-10 (Regional Energy Reactor, 10MWth) has been developed to maintain system safety in order to be placed in a densely populated region, or island, etc. The REX-10 reactor system was designed based on SMART, however, the operation mode and the system pressure and capacity were determined properly for a regional energy reactor. In this study, the design characteristics of REX-10 and the related researches will be introduced.

  4. Solar array design based on shadow analysis for increasing net energy collection in a competition vehicle

    Science.gov (United States)

    Osorio-Gómez, Gilberto; Mejía-Gutiérrez, Ricardo; Suárez-Castañeda, Nicolás; Gil-Herrera, Ana; Barrera-Velásquez, Jorge

    2015-01-01

    Photovoltaic (PV) applications such as in the architectural, automotive, and aerospace industries face design contradictions because they are expected to produce a lot of energy but are constrained by available area, surface shape, incident irradiance, shadows, and other aspects that have a negative influence on the energy produced by the solar panel. Solar competition vehicles are some of these challenging PV applications. The design of such solar arrays needs to consider efficiency evaluation in order to optimize space; it is difficult not to install solar modules in areas impacted by shadows. A design procedure for a solar array configuration based on shadow analysis for competition vehicles is presented. The principle is that shadows in moving objects can be simulated, since the vehicle, the earth and the sun are are moving in semipredictable patterns, thus net energy collection can be forecast. The case study presented is the solar array design of a vehicle that participated in the World Solar Challenge 2013. The obtained results illustrate how the employment of the procedure gives insights on important aspects to consider and also delivers qualitative and quantitative information for decision making. In addition, the experience in competition highlights some issues to be considered, modified, or improved in further vehicle designs.

  5. Design and optimization of an RF energy harvesting system from multiple sources

    Science.gov (United States)

    Ali, Mai; Albasha, Lutfi; Qaddoumi, Nasser

    2013-05-01

    This paper presents the design and optimization of an RF energy harvesting system from multiple sources. The RF power is harvested from four frequency bands representing five wireless systems, namely GSM, UMTS, DTV, Wi-Fi, and road tolling system. A Schottky diode model was developed based on which an RF-DC rectifier joined with a voltage multiplier circuits were designed. The simulation results of the complete RF harvesting system showed superior performance to similar state of the art systems. To further optimize the design, and to eliminate use of a non-standard CMOS process associated with Schottky diodes, the Schottky diode based rectifier was replaced by diode connected transistor configuration based on self-threshold cancellation (SVC) technique.

  6. Energy system simulation in performance-based building design

    NARCIS (Netherlands)

    Wilde, P.J.C.J. de; Augenbroe, G.; Voorden, M. van der

    2002-01-01

    This paper discusses the requirements and possible solutions for the use of building simulation tools as instrument to support performance-based building design decisions. Use of an existing simulation tool to support a specific building design decision (the selection of energy saving building compo

  7. Principle design of an energy efficient transfemoral prosthesis

    NARCIS (Netherlands)

    Ünal, R.; Hekman, E.E.G.; Carloni, R.; Koopman, H.F.J.M.; Stramigioli, S.

    2009-01-01

    In the pursuit of realizing an energy efficient transfemoral prosthetic, in this paper we present a preliminary study on a principle design. In particular, the design is based on the idea that the efficiency of the system can be realized by energetically coupling the knee and the ankle joints. In or

  8. Architectural design and energy performance; Conception architecturale et performance energetique

    Energy Technology Data Exchange (ETDEWEB)

    Beaud, Ph. [Agence de l' Environnement et de la Maitrise de l' Energie, (ADEME), 06 - Valbonne (France); Pouget, A. [Bureau Etude Thermique, 75 - Paris (France); Sesolis, B. [TRIBU, 75 - Paris (France)] [and others

    2000-07-01

    This day was organized around the energy performance of the architecture in three parts. A first time dealt with the design of new buildings and private houses. Simulation tools for the energy optimization and practice of design are discussed. The second part was devoted to the new 2000 regulation with an open discussion on the regulatory costs. The last part forecasted the evolution until 2015 taking into account the french program of fight against the greenhouse effect, the limitation of the air conditioning consumption and the definition of a quality label concerning the energy performances. (A.L.B.)

  9. Achieving 50% Energy Savings in Office Buildings, Advanced Energy Design Guides: Office Buildings (Brochure)

    Energy Technology Data Exchange (ETDEWEB)

    2014-09-01

    This fact sheet summarizes recommendations for designing new office buildings that result in 50% less energy use than conventional designs meeting minimum code requirements. The recommendations are drawn from the Advanced Energy Design Guide for Small to Medium Office Buildings, an ASHRAE publication that provides comprehensive recommendations for designing low-energy-use office buildings with gross floor areas up to 100,000 ft2 (see sidebar). Designed as a stand-alone document, this fact sheet provides key principles and a set of prescriptive design recommendations appropriate for smaller office buildings with insufficient budgets to fully implement best practices for integrated design and optimized performance. The recommendations have undergone a thorough analysis and review process through ASHRAE, and have been deemed the best combination of measures to achieve 50% savings in the greatest number of office buildings.

  10. Zero Energy Buildings – Design Principles and Built Examples

    DEFF Research Database (Denmark)

    knowledge must be acquired, depending on the project in question. Through a cross-disciplinary approach to architecture and building design, and based on an integrated design process, this publication will: • introduce a number of design strategies and technologies which are particularly important....... The purpose of this booklet is to support the integrated design process and co-operation between different professions. The subject areas are therefore described at a general level, to provide the engineer with an insight into the techniques used by the architect, and vice versa. Additionally, specialist...... for the development of zero energy houses. These strategies and technologies are illustrated through simple design principles and built examples • identify technical and architectural potentials and challenges related to design strategies of crucial importance to the development of zero energy houses • identify...

  11. Design requirements for interfaces in solar energy conversion technologies

    Science.gov (United States)

    Butler, B. L.

    1982-04-01

    Candidate materials for improving the durability and economics of solar energy conversion systems (SECS) are reviewed. A 30-yr lifetime is regarded as necessary for solar collector and concentrator materials in order to offset the high initial costs of SECS in parabolic dish, heliostat, parabolic trough, flat plate collector, OTEC, solar cell, and wind turbine configurations. The materials are required to transfer a maximum amount of intercepted energy without degrading from exposure to UV radiation, wind, water, dust, and temperature cycling. Glass and mirrored surfaces for reflecting or refracting optical subsystems are currently made from soda-lime, boro- and aluminosilicate, and must resist chemicals, abrasion, and permeability, and have good strength, flexibility, coefficient of expansion, and Young's modulus. Additional concerns are present in photochemical, solar cell, and in substrata components and systems.

  12. The Design of the LED Display based on Solar Energy

    Directory of Open Access Journals (Sweden)

    Li Pei

    2015-01-01

    Full Text Available The development of solar energy and the LED display, the superiority of the combination of them and software design of the system are discussed in this paper. Hardware design and software design are the key elements of this paper. Solar control circuit, LED display control circuit, etc are described, charge and discharge of the battery and output of the battery is controlled by STC89C52 SCM. The design of software provides driver to the related hardware circuit. The result of the experiment have achieved anticipated effects and met the design requirements.

  13. Designing an Energy Drink: High School Students Learn Design and Marketing Skills in This Activity

    Science.gov (United States)

    Martin, Doug

    2008-01-01

    A decade ago, energy drinks were almost nonexistent in the United States, but in the past five years they've become wildly popular. In fact, the $3.4 billion energy-drink market is expected to double this year alone, and the younger generation is the market targeted by manufacturers. This article presents an energy-drink designing activity. This…

  14. Designing an Energy Drink: High School Students Learn Design and Marketing Skills in This Activity

    Science.gov (United States)

    Martin, Doug

    2008-01-01

    A decade ago, energy drinks were almost nonexistent in the United States, but in the past five years they've become wildly popular. In fact, the $3.4 billion energy-drink market is expected to double this year alone, and the younger generation is the market targeted by manufacturers. This article presents an energy-drink designing activity. This…

  15. Energy model development and heating energy investigation of the Nested Thermal Envelope Design (NTED(TM))

    Science.gov (United States)

    Dixon, Elizabeth Erin

    Space heating accounts for approximately 60% of residential energy use in Canada. Minimizing envelope heat losses is one approach to reducing this percentage. Preliminary research investigated the energy-saving potential of an innovative design, referred to as Nested Thermal Envelope Design (NTED(TM)). The concept involves one insulated building inside another with dual thermal zones. Conservative modeling results from this work showed heating energy reductions of 74%. This research developed a new NTED(TM) simulation model to provide increased accuracy and gain a more complete understanding of the potential heating energy savings. The working performance was also investigated by modeling occupied-building operation. The resulting model has shown that the NTED(TM) design yields savings of 85% relative to a benchmark R-2000 building. These results improve on the preliminary values and reinforce the merit of the design as a means of achieving significant reductions in residential energy use.

  16. A Design Outline for Floating Point Absorber Wave Energy Converters

    Directory of Open Access Journals (Sweden)

    Mohammed Faizal

    2014-04-01

    Full Text Available An overview of the most important development stages of floating point absorber wave energy converters is presented. At a given location, the wave energy resource has to be first assessed for varying seasons. The mechanisms used to convert wave energy to usable energy vary for different wave energy conversion systems. The power output of the generator will have variations due to varying incident waves. The wave structure-interaction leads to modifications in the incident waves; thus, the power output is also affected. The device has to be stable enough to prevent itself from capsizing. The point absorber will give optimum performance when the incident wave frequencies correspond to the natural frequency of the device. The methods for calculating natural frequencies for pitching and heaving systems are presented. Mooring systems maintain the point absorber at the desired location. Various mooring configurations as well as the most commonly used materials for mooring lines are discussed. An overview of scaled modelling is also presented.

  17. Design and Testing of CPAS Main Deployment Bag Energy Modulator

    Science.gov (United States)

    Mollmann, Catherine

    2017-01-01

    During the developmental testing program for CPAS (Capsule Parachute Assembly System), the parachute system for the NASA Orion Crew Module, simulation revealed that high loads may be experienced by the pilot risers during the most devere deployment conditions. As the role of the pilot parachutes is to deploy the main parachutes, these high loads introduced the possibility of main deployment failure. In order to mitigate these high loads, a set of energy modulators was incorporated between the pilot riser and the main deployment bag. An extensive developmental program was implemented to ensure the adequacy of these energy modulators. After initial design comparisons, the energy modulator design was validated through slow-speed joint tests as well as through high-speed bungee tests. This paper documents the design, development, and results of multiple tests completed on the final design.

  18. Energy policy design and China’s local climate governance

    DEFF Research Database (Denmark)

    Ting, Guan; Delman, Jørgen

    2017-01-01

    This study probes into climate policy design at city level in China, with Hangzhou’s energy efficiency and renewable energy policies between 2005 and 2014 as a case. The study applies a political action arena approach to accentuate the importance of different normative preferences behind climate...... energy efficiency is a more mature and comprehensive political action arena than renewable energy. The study also finds that there has been a significant shift away from preferences towards command-and-control to more marketbased instruments, while cooperative governance instruments are still...

  19. 一种翼艇式飞行器方案研究%Exploring Effective Configuration Design of a Winged Airship

    Institute of Scientific and Technical Information of China (English)

    王海峰; 宋笔锋; 钟小平

    2011-01-01

    Aim. The introduction of the full paper discusses existing problems and then proposes our exploration,which is explained in sections 1, 2 and 3. To solve two critical problems for the flight of a winged airship in near space at low speed, section 1 uses rarefied air to produce the lift of a winged airship and balance its weight and the limited solar energy to produce the power needed by the winged airship for long-time flight. Section 2 designs the configuration of the winged airship; its core consists of: ( 1 ) the lift and buoyancy integration mode and the daynight energy saving mode are used for the winged airship; (2) we use the iteration method to calculate the design parameters of the winged airship, the iteration flow chart being given in the block diagram shown in Fig. 3. Section 3 designs the optimal parameters of the winged airship; its core is that we use the NSGA( non-dominated sorting genetic algorithm) to perform the multi-objective optimization of the winged airship; the design results, given in Tables 2 and 3 and Fig. 4, and their analysis show preliminarily that: ( 1 ) the total weight of lithium batteries used at night is much smaller; (2) the volume of winged airship is much smaller; (3) its flight velocity is much greater than that of the airship in near space. Section 4 draws the preliminary conclusions that: ( 1 ) the winged airship is suitable for the payload of Doppler effect such as synthetic aperture radar (SAR); (2) the size of the airship in near space which is obtained by using our design method is close to that of the high-altitude airship published by Lockheed Martin Inc, indicating that our design method for the winged airship is effective.%文章提出了一种翼艇式飞行器方案,较好地解决了以低速在临近空间飞行的两个关键问题:①如何利用临近空间稀薄空气产生升力克服飞行器重量;②如何有效利用有限太阳能产生飞行器长时间飞行的动力.该飞行器采用了升浮一

  20. Sensitivity Analysis Applied in Design of Low Energy Office Building

    DEFF Research Database (Denmark)

    Heiselberg, Per; Brohus, Henrik

    2008-01-01

    Building performance can be expressed by different indicators as primary energy use, environmental load and/or the indoor environmental quality and a building performance simulation can provide the decision maker with a quantitative measure of the extent to which an integrated design solution...... satisfies the design requirements and objectives. In the design of sustainable Buildings it is beneficial to identify the most important design parameters in order to develop more efficiently alternative design solutions or reach optimized design solutions. A sensitivity analysis makes it possible...... to identify the most important parameters in relation to building performance and to focus design and optimization of sustainable buildings on these fewer, but most important parameters. The sensitivity analyses will typically be performed at a reasonably early stage of the building design process, where...

  1. Aiding Design of Wave Energy Converters via Computational Simulations

    Science.gov (United States)

    Jebeli Aqdam, Hejar; Ahmadi, Babak; Raessi, Mehdi; Tootkaboni, Mazdak

    2015-11-01

    With the increasing interest in renewable energy sources, wave energy converters will continue to gain attention as a viable alternative to current electricity production methods. It is therefore crucial to develop computational tools for the design and analysis of wave energy converters. A successful design requires balance between the design performance and cost. Here an analytical solution is used for the approximate analysis of interactions between a flap-type wave energy converter (WEC) and waves. The method is verified using other flow solvers and experimental test cases. Then the model is used in conjunction with a powerful heuristic optimization engine, Charged System Search (CSS) to explore the WEC design space. CSS is inspired by charged particles behavior. It searches the design space by considering candidate answers as charged particles and moving them based on the Coulomb's laws of electrostatics and Newton's laws of motion to find the global optimum. Finally the impacts of changes in different design parameters on the power takeout of the superior WEC designs are investigated. National Science Foundation, CBET-1236462.

  2. Configuration by Modularisation

    DEFF Research Database (Denmark)

    Riitahuhta, Asko; Andreasen, Mogens Myrup

    1998-01-01

    Globally operating companies have realized that locally customized products and services are today the prerequisite for the success. The capability or the paradigm to act locally in global markets is called Mass Customization [Victor 1997]. The prerequisite for Mass Customization is Configuration...... for the creation of a structured product family is presented and examples are given. The concepts of a novel Dynamic Modularisation method, Metrics for Modularisation and Design for Configurability are presented....

  3. Hypertext Configurations

    DEFF Research Database (Denmark)

    Finnemann, Niels Ole

    2016-01-01

    , links, interactive processes, and time scalings, and that the hypertext configuration is a major but not sole source of the messiness of big data. The notion of hypertext will be revalidated, placed at the center of the interpretation of networked digital media, and used in the analysis of the fast...

  4. Qualitative Analysis of the Helical Electronic Energy of Inherently Chiral Calix[4]arenes: An Approach to Effectively Assign Their Absolute Configuration

    Directory of Open Access Journals (Sweden)

    Shuang Zheng

    2014-06-01

    Full Text Available For all microhelices on aromatic rings of inherently chiral calix[4]arene, an expression was derived from one approximation and one hypothesis on the basis of the electron-on-a-helix model of Tinoco and Woody as follows: 1/E = μ (H − K Δα2 , where μ = 1 for the right-handed microhelix and μ = −1 for the left-handed microhelix; and H and K are constant and greater than zero. The expression correlates microhelical electronic energy (E with the atom polarizability difference (Δα on both microhelix ends, which intuitively and clearly shows the impact of helical substituent polarizability on helical electronic energy. The case analysis almost entirely proves that the qualitative analysis of the helical electronic energy of inherently chiral calix[4]arenes with the expression is scientific and can be used to effectively assign their absolute configuration

  5. Cosmic Ray Composition and Energy Spectrum from 1-30 PeV Using the 40-String Configuration of IceTop and IceCube

    CERN Document Server

    Abbasi, R; Ackermann, M; Adams, J; Aguilar, J A; Ahlers, M; Altmann, D; Andeen, K; Auffenberg, J; Bai, X; Baker, M; Barwick, S W; Baum, V; Bay, R; Beattie, K; Beatty, J J; Bechet, S; Tjus, J Becker; Becker, K -H; Bell, M; Benabderrahmane, M L; BenZvi, S; Berdermann, J; Berghaus, P; Berley, D; Bernardini, E; Bertrand, D; Besson, D Z; Bindig, D; Bissok, M; Blaufuss, E; Blumenthal, J; Boersma, D J; Bohm, C; Bose, D; Böser, S; Botner, O; Brayeur, L; Brown, A M; Bruijn, R; Brunner, J; Buitink, S; Caballero-Mora, K S; Carson, M; Casey, J; Casier, M; Chirkin, D; Christy, B; Clevermann, F; Cohen, S; Cowen, D F; Silva, A H Cruz; Danninger, M; Daughhetee, J; Davis, J C; De Clercq, C; Descamps, F; Desiati, P; de Vries-Uiterweerd, G; DeYoung, T; Díaz-Vélez, J C; Dreyer, J; Dumm, J P; Dunkman, M; Eagan, R; Eisch, J; Ellsworth, R W; Engdegård, O; Euler, S; Evenson, P A; Fadiran, O; Fazely, A R; Fedynitch, A; Feintzeig, J; Feusels, T; Filimonov, K; Finley, C; Fischer-Wasels, T; Flis, S; Franckowiak, A; Franke, R; Frantzen, K; Fuchs, T; Gaisser, T K; Gallagher, J; Gerhardt, L; Gladstone, L; Glüsenkamp, T; Goldschmidt, A; Goodman, J A; Góra, D; Grant, D; Groß, A; Grullon, S; Gurtner, M; Ha, C; Ismail, A Haj; Hallgren, A; Halzen, F; Hanson, K; Heereman, D; Heimann, P; Heinen, D; Helbing, K; Hellauer, R; Hickford, S; Hill, G C; Hoffman, K D; Hoffmann, R; Homeier, A; Hoshina, K; Huelsnitz, W; Hulth, P O; Hultqvist, K; Hussain, S; Ishihara, A; Jacobi, E; Jacobsen, J; Japaridze, G S; Jlelati, O; Johansson, H; Kappes, A; Karg, T; Karle, A; Kiryluk, J; Kislat, F; Kläs, J; Klein, S R; Köhne, J -H; Kohnen, G; Kolanoski, H; Köpke, L; Kopper, C; Kopper, S; Koskinen, D J; Kowalski, M; Krasberg, M; Kroll, G; Kunnen, J; Kurahashi, N; Kuwabara, T; Labare, M; Laihem, K; Landsman, H; Larson, M J; Lauer, R; Lesiak-Bzdak, M; Lünemann, J; Madsen, J; Maruyama, R; Mase, K; Matis, H S; McNally, F; Meagher, K; Merck, M; Mészáros, P; Meures, T; Miarecki, S; Middell, E; Milke, N; Miller, J; Mohrmann, L; Montaruli, T; Morse, R; Movit, S M; Nahnhauer, R; Naumann, U; Nowicki, S C; Nygren, D R; Obertacke, A; Odrowski, S; Olivas, A; Olivo, M; O'Murchadha, A; Panknin, S; Paul, L; Pepper, J A; Heros, C Pérez de los; Pieloth, D; Pirk, N; Posselt, J; Price, P B; Przybylski, G T; Rädel, L; Rawlins, K; Redl, P; Resconi, E; Rhode, W; Ribordy, M; Richman, M; Riedel, B; Rodrigues, J P; Rothmaier, F; Rott, C; Ruhe, T; Rutledge, D; Ruzybayev, B; Ryckbosch, D; Saba, S M; Salameh, T; Sander, H -G; Santander, M; Sarkar, S; Schatto, K; Scheel, M; Scheriau, F; Schmidt, T; Schmitz, M; Schoenen, S; Schöneberg, S; Schönherr, L; Schönwald, A; Schukraft, A; Schulte, L; Schulz, O; Seckel, D; Seo, S H; Sestayo, Y; Seunarine, S; Smith, M W E; Soiron, M; Soldin, D; Spiczak, G M; Spiering, C; Stamatikos, M; Stanev, T; Stasik, A; Stezelberger, T; Stokstad, R G; Stößl, A; Strahler, E A; Ström, R; Sullivan, G W; Taavola, H; Taboada, I; Tamburro, A; Ter-Antonyan, S; Tilav, S; Toale, P A; Toscano, S; Usner, M; van Eijndhoven, N; van der Drift, D; Van Overloop, A; van Santen, J; Vehring, M; Voge, M; Walck, C; Waldenmaier, T; Wallraff, M; Walter, M; Wasserman, R; Weaver, Ch; Wendt, C; Westerhoff, S; Whitehorn, N; Wiebe, K; Wiebusch, C H; Williams, D R; Wissing, H; Wolf, M; Wood, T R; Woschnagg, K; Xu, C; Xu, D L; Xu, X W; Yanez, J P; Yodh, G; Yoshida, S; Zarzhitsky, P; Ziemann, J; Zilles, A; Zoll, M

    2012-01-01

    The mass composition of high energy cosmic rays depends on their production, acceleration, and propagation. The study of cosmic ray composition can therefore reveal hints of the origin of these particles. At the South Pole, the IceCube Neutrino Observatory is capable of measuring two components of cosmic ray air showers in coincidence: the electromagnetic component at high altitude (2835 m) using the IceTop surface array, and the muonic component above ~1 TeV using the IceCube array. This unique detector arrangement provides an opportunity for precision measurements of the cosmic ray energy spectrum and composition in the region of the knee and beyond. We present the results of a neural network analysis technique to study the cosmic ray composition and the energy spectrum from 1 PeV to 30 PeV using data recorded using the 40-string/40-station configuration of the IceCube Neutrino Observatory.

  6. Cosmic ray composition and energy spectrum from 1-30 PeV using the 40-string configuration of IceTop and IceCube

    Science.gov (United States)

    IceCube Collaboration; Abbasi, R.; Abdou, Y.; Ackermann, M.; Adams, J.; Aguilar, J. A.; Ahlers, M.; Altmann, D.; Andeen, K.; Auffenberg, J.; Bai, X.; Baker, M.; Barwick, S. W.; Baum, V.; Bay, R.; Beattie, K.; Beatty, J. J.; Bechet, S.; Becker, J. K.; Becker, K.-H.; Bell, M.; Benabderrahmane, M. L.; BenZvi, S.; Berdermann, J.; Berghaus, P.; Berley, D.; Bernardini, E.; Bertrand, D.; Besson, D. Z.; Bindig, D.; Bissok, M.; Blaufuss, E.; Blumenthal, J.; Boersma, D. J.; Bohm, C.; Bose, D.; Böser, S.; Botner, O.; Brayeur, L.; Brown, A. M.; Bruijn, R.; Brunner, J.; Buitink, S.; Caballero-Mora, K. S.; Carson, M.; Casey, J.; Casier, M.; Chirkin, D.; Christy, B.; Clevermann, F.; Cohen, S.; Cowen, D. F.; Silva, A. H. Cruz; Danninger, M.; Daughhetee, J.; Davis, J. C.; De Clercq, C.; Descamps, F.; Desiati, P.; de Vries-Uiterweerd, G.; DeYoung, T.; Díaz-Vélez, J. C.; Dreyer, J.; Dumm, J. P.; Dunkman, M.; Eagan, R.; Eisch, J.; Ellsworth, R. W.; Engdegård, O.; Euler, S.; Evenson, P. A.; Fadiran, O.; Fazely, A. R.; Fedynitch, A.; Feintzeig, J.; Feusels, T.; Filimonov, K.; Finley, C.; Fischer-Wasels, T.; Flis, S.; Franckowiak, A.; Franke, R.; Frantzen, K.; Fuchs, T.; Gaisser, T. K.; Gallagher, J.; Gerhardt, L.; Gladstone, L.; Glüsenkamp, T.; Goldschmidt, A.; Goodman, J. A.; Góra, D.; Grant, D.; Groß, A.; Grullon, S.; Gurtner, M.; Ha, C.; Ismail, A. Haj; Hallgren, A.; Halzen, F.; Hanson, K.; Heereman, D.; Heimann, P.; Heinen, D.; Helbing, K.; Hellauer, R.; Hickford, S.; Hill, G. C.; Hoffman, K. D.; Hoffmann, R.; Homeier, A.; Hoshina, K.; Huelsnitz, W.; Hulth, P. O.; Hultqvist, K.; Hussain, S.; Ishihara, A.; Jacobi, E.; Jacobsen, J.; Japaridze, G. S.; Jlelati, O.; Johansson, H.; Kappes, A.; Karg, T.; Karle, A.; Kiryluk, J.; Kislat, F.; Kläs, J.; Klein, S. R.; Köhne, J.-H.; Kohnen, G.; Kolanoski, H.; Köpke, L.; Kopper, C.; Kopper, S.; Koskinen, D. J.; Kowalski, M.; Krasberg, M.; Kroll, G.; Kunnen, J.; Kurahashi, N.; Kuwabara, T.; Labare, M.; Laihem, K.; Landsman, H.; Larson, M. J.; Lauer, R.; Lesiak-Bzdak, M.; Lünemann, J.; Madsen, J.; Maruyama, R.; Mase, K.; Matis, H. S.; McNally, F.; Meagher, K.; Merck, M.; Mészáros, P.; Meures, T.; Miarecki, S.; Middell, E.; Milke, N.; Miller, J.; Mohrmann, L.; Montaruli, T.; Morse, R.; Movit, S. M.; Nahnhauer, R.; Naumann, U.; Nowicki, S. C.; Nygren, D. R.; Obertacke, A.; Odrowski, S.; Olivas, A.; Olivo, M.; O'Murchadha, A.; Panknin, S.; Paul, L.; Pepper, J. A.; de los Heros, C. Pérez; Pieloth, D.; Pirk, N.; Posselt, J.; Price, P. B.; Przybylski, G. T.; Rädel, L.; Rawlins, K.; Redl, P.; Resconi, E.; Rhode, W.; Ribordy, M.; Richman, M.; Riedel, B.; Rodrigues, J. P.; Rothmaier, F.; Rott, C.; Ruhe, T.; Rutledge, D.; Ruzybayev, B.; Ryckbosch, D.; Salameh, T.; Sander, H.-G.; Santander, M.; Sarkar, S.; Saba, S. M.; Schatto, K.; Scheel, M.; Scheriau, F.; Schmidt, T.; Schmitz, M.; Schoenen, S.; Schöneberg, S.; Schönherr, L.; Schönwald, A.; Schukraft, A.; Schulte, L.; Schulz, O.; Seckel, D.; Seo, S. H.; Sestayo, Y.; Seunarine, S.; Smith, M. W. E.; Soiron, M.; Soldin, D.; Spiczak, G. M.; Spiering, C.; Stamatikos, M.; Stanev, T.; Stasik, A.; Stezelberger, T.; Stokstad, R. G.; Stößl, A.; Strahler, E. A.; Ström, R.; Sullivan, G. W.; Taavola, H.; Taboada, I.; Tamburro, A.; Ter-Antonyan, S.; Tilav, S.; Toale, P. A.; Toscano, S.; Usner, M.; van Eijndhoven, N.; van der Drift, D.; Van Overloop, A.; van Santen, J.; Vehring, M.; Voge, M.; Walck, C.; Waldenmaier, T.; Wallraff, M.; Walter, M.; Wasserman, R.; Weaver, Ch.; Wendt, C.; Westerhoff, S.; Whitehorn, N.; Wiebe, K.; Wiebusch, C. H.; Williams, D. R.; Wissing, H.; Wolf, M.; Wood, T. R.; Woschnagg, K.; Xu, C.; Xu, D. L.; Xu, X. W.; Yanez, J. P.; Yodh, G.; Yoshida, S.; Zarzhitsky, P.; Ziemann, J.; Zilles, A.; Zoll, M.

    2013-02-01

    The mass composition of high energy cosmic rays depends on their production, acceleration, and propagation. The study of cosmic ray composition can therefore reveal hints of the origin of these particles. At the South Pole, the IceCube Neutrino Observatory is capable of measuring two components of cosmic ray air showers in coincidence: the electromagnetic component at high altitude (2835 m) using the IceTop surface array, and the muonic component above ˜1 TeV using the IceCube array. This unique detector arrangement provides an opportunity for precision measurements of the cosmic ray energy spectrum and composition in the region of the knee and beyond. We present the results of a neural network analysis technique to study the cosmic ray composition and the energy spectrum from 1 PeV to 30 PeV using data recorded using the 40-string/40-station configuration of the IceCube Neutrino Observatory.

  7. Achieving 50% Energy Savings in New Schools, Advanced Energy Design Guides: K-12 Schools (Brochure)

    Energy Technology Data Exchange (ETDEWEB)

    2014-09-01

    This fact sheet summarizes recommendations for designing elementary, middle, and high school buildings that will result in 50% less energy use than conventional new schools built to minimum code requirements. The recommendations are drawn from the Advanced Energy Design Guide for K-12 School Buildings, an ASHRAE publication that provides comprehensive recommendations for designing low-energy-use school buildings (see sidebar). Designed as a stand-alone document, this fact sheet provides key principles and a set of prescriptive design recommendations appropriate for smaller schools with insufficient budgets to fully implement best practices for integrated design and optimized performance. The recommendations have undergone a thorough analysis and review process through ASHRAE, and have been deemed the best combination of measures to achieve 50% savings in the greatest number of schools.

  8. Optimizing Existing Multistory Building Designs towards Net-Zero Energy

    Directory of Open Access Journals (Sweden)

    Mohammad Y. AbuGrain

    2017-03-01

    Full Text Available Recent global developments in awareness and concerns about environmental problems have led to reconsidering built environment approaches and construction techniques. One of the alternatives is the principle of low/zero-energy buildings. This study investigates the potentials of energy savings in an existing multi-story building in the Mediterranean region in order to achieve net-zero energy as a solution to increasing fossil fuel prices. The Colored building at the Faculty of Architecture, Eastern Mediterranean University, Cyprus was chosen as a target of this study to be investigated and analyzed in order to know how energy efficiency strategies could be applied to the building to reduce annual energy consumption. Since this research objective is to develop a strategy to achieve net-zero energy in existing buildings, case study and problem solving methodologies were applied in this research in order to evaluate the building design in a qualitative manner through observations, in addition to a quantitative method through an energy modeling simulation to achieve desirable results which address the problems. After optimizing the building energy performance, an alternative energy simulation was made of the building in order to make an energy comparison analysis, which leads to reliable conclusions. These methodologies and the strategies used in this research can be applied to similar buildings in order to achieve net-zero energy goals.

  9. Feasibility and Optimal Design of a Stand-Alone Photovoltaic Energy System for the Orphanage

    Directory of Open Access Journals (Sweden)

    Vincent Anayochukwu Ani

    2014-01-01

    Full Text Available Access to electricity can have a positive psychological impact through a lessening of the sense of exclusion, and vulnerability often felt by the orphanages. This paper presented the simulation and optimization study of a stand-alone photovoltaic power system that produced the desired power needs of an orphanage. Solar resources for the design of the system were obtained from the National Aeronautics and Space Administration (NASA Surface Meteorology and Solar Energy website at a location of 6°51′N latitude and 7°35′E longitude, with annual average solar radiation of 4.92 kWh/m2/d. This study is based on modeling, simulation, and optimization of energy system in the orphanage. The patterns of load consumption within the orphanage were studied and suitably modeled for optimization. Hybrid Optimization Model for Electric Renewables (HOMER software was used to analyze and design the proposed stand-alone photovoltaic power system model. The model was designed to provide an optimal system configuration based on an hour-by-hour data for energy availability and demands. A detailed design, description, and expected performance of the system were presented in this paper.

  10. Advanced Energy Design Guide for Small Hospitals and Healthcare Facilities

    Directory of Open Access Journals (Sweden)

    Eric Bonnema

    2010-01-01

    Full Text Available The Advanced Energy Design Guide for Small Hospitals and Healthcare Facilities (AEDG-SHC was recently completed. It is the sixth document in a series of guides designed to achieve 30% savings over the minimum code requirements of ANSI/ASHRAE/IESNA Standard 90.1-1999. The guide [1] is available for print purchase or as a free download from http://www.ashrae.org/aedg and provides user-friendly assistance and recommendations for the building design, construction, and owner communities to achieve energy savings. Included in the guide are prescriptive recommendations for quality assurance and commissioning; design of the building envelope; fenestration; lighting systems (including electric lighting and daylighting; heating, ventilation, and air-conditioning (HVAC systems; building automation and controls; outside air (OA treatment; and service water heating (SWH. The guide educates, provides practical recommendations for exceeding code minimums, and provides leadership to help design teams and owners produce higher efficiency commercial buildings.

  11. Design, Synthesis and Evaluation of Organic Non-linear Optical Chromophores with Configurationally and Conformationally Locked Polyene Bridges

    Science.gov (United States)

    2007-11-02

    A modular, synthetic scheme was developed for versatile variation of donors, acceptors and polyene bridge length of NLO-chromophores. Configurational...and conformational rigidity of the polyene bridges were realized by making each set of adjacent double and single bond pair part of a fused...cylohexene ring. Substituent effects on the reactions leading to the establishment of the donor, elongation of the fused polyene bridge and the final

  12. Tribological design constraints of marine renewable energy systems.

    Science.gov (United States)

    Wood, Robert J K; Bahaj, AbuBakr S; Turnock, Stephen R; Wang, Ling; Evans, Martin

    2010-10-28

    Against the backdrop of increasing energy demands, the threat of climate change and dwindling fuel reserves, finding reliable, diverse, sustainable/renewable, affordable energy resources has become a priority for many countries. Marine energy conversion systems are at the forefront of providing such a resource. Most marine renewable energy conversion systems require tribological components to convert wind or tidal streams to rotational motion for generating electricity while wave machines typically use oscillating hinge or piston within cylinder geometries to promote reciprocating linear motion. This paper looks at the tribology of three green marine energy systems, offshore wind, tidal and wave machines. Areas covered include lubrication and contamination, bearing and gearbox issues, biofouling, cavitation erosion, tribocorrosion, condition monitoring as well as design trends and loading conditions associated with tribological components. Current research thrusts are highlighted along with areas needing research as well as addressing present-day issues related to the tribology of offshore energy conversion technologies.

  13. About lamination upper and convexification lower bounds on the free energy of monoclinic shape memory alloys in the context of T 3-configurations and R-phase formation

    Science.gov (United States)

    Fechte-Heinen, R.; Schlömerkemper, A.

    2016-11-01

    This work is concerned with different estimates of the quasiconvexification of multi-well energy landscapes of NiTi shape memory alloys, which models the overall behavior of the material. Within the setting of the geometrically linear theory of elasticity, we consider a formula of the quasiconvexification which involves the so-called energy of mixing.We are interested in lower and upper bounds on the energy of mixing in order to get a better understanding of the quasiconvexification. The lower bound on the energy of mixing is obtained by convexification; it is also called Sachs or Reuß lower bound. The upper bound on the energy of mixing is based on second-order lamination. In particular, we are interested in the difference between the lower and upper bounds. Our numerical simulations show that the difference is in fact of the order of 1% and less in martensitic NiTi, even though both bounds on the energy of mixing were rather expected to differ more significantly. Hence, in various circumstances it may be justified to simply work with the convexification of the multi-well energy, which is relatively easy to deal with, or with the lamination upper bound, which always corresponds to a physically realistic microstructure, as an estimate of the quasiconvexification. In order to obtain a potentially large difference between upper and lower bound, we consider the bounds along paths in strain space which involve incompatible strains. In monoclinic shape memory alloys, three-tuples of pairwise incompatible strains play a special role since they form so-called T 3-configurations, originally discussed in a stress-free setting. In this work, we therefore consider in particular numerical simulations along paths in strain space which are related to these T 3-configurations. Interestingly, we observe that the second-order lamination upper bound along such paths is related to the geometry of the T 3-configurations. In addition to the purely martensitic regime, we also consider

  14. Innovative use of strategic energy design tools in building design in China

    Institute of Scientific and Technical Information of China (English)

    LIBaizhan; R.Yao; N.Baker; K.Steemers

    2003-01-01

    This paper expresses the importance of the use of strategic energy design tool in building design in China. The features of this kind of tool have been illustrated. The reliability, user friendliness, and usability are the most important characteristic of the early design software. This paper introduces an integrated energy design tool - LT Europe, which is widely used in the UK architectural practice and European. The climate data for Beijing has been produced from Meteonorm and integrated into LT Europe. A case study has been performed and the comparisons have been made by applying the Chinese old and new building energy regulations. It has been demonstrated that LT Europe software can be used for Chinese building energy design at the early stage by creating the local proper climate data.

  15. Modeling and design of energy concentrating laser weld joints

    Energy Technology Data Exchange (ETDEWEB)

    Milewski, J.O. [Los Alamos National Lab., NM (United States); Sklar, E. [OptiCad Corp., Santa Fe, NM (United States)

    1997-04-01

    The application of lasers for welding and joining has increased steadily over the past decade with the advent of high powered industrial laser systems. Attributes such as high energy density and precise focusing allow high speed processing of precision assemblies. Other characteristics of the process such as poor coupling of energy due to highly reflective materials and instabilities associated with deep penetration keyhole mode welding remain as process limitations and challenges to be overcome. Reflective loss of laser energy impinging on metal surfaces can in some cases exceed ninety five percent, thus making the process extremely inefficient. Enhanced coupling of the laser beam can occur when high energy densities approach the vaporization point of the materials and form a keyhole feature which can trap laser energy and enhance melting and process efficiency. The extreme temperature, pressure and fluid flow dynamics of the keyhole make control of the process difficult in this melting regime. The authors design and model weld joints which through reflective propagation and concentration of the laser beam energy significantly enhance the melting process and weld morphology. A three dimensional computer based geometric optical model is used to describe the key laser parameters and joint geometry. Ray tracing is used to compute the location and intensity of energy absorption within the weld joint. Comparison with experimentation shows good correlation of energy concentration within the model to actual weld profiles. The effect of energy concentration within various joint geometry is described. This method for extending the design of the laser system to include the weld joint allows the evaluation and selection of laser parameters such as lens and focal position for process optimization. The design of narrow gap joints which function as energy concentrators is described. The enhanced laser welding of aluminum without keyhole formation has been demonstrated.

  16. Enhancing Energy Efficiency of Wireless Sensor Network through the Design of Energy Efficient Routing Protocol

    Directory of Open Access Journals (Sweden)

    Noor Zaman

    2016-01-01

    Full Text Available Wireless Sensor Network (WSN is known to be a highly resource constrained class of network where energy consumption is one of the prime concerns. In this research, a cross layer design methodology was adopted to design an energy efficient routing protocol entitled “Position Responsive Routing Protocol” (PRRP. PRRP is designed to minimize energy consumed in each node by (1 reducing the amount of time in which a sensor node is in an idle listening state and (2 reducing the average communication distance over the network. The performance of the proposed PRRP was critically evaluated in the context of network lifetime, throughput, and energy consumption of the network per individual basis and per data packet basis. The research results were analyzed and benchmarked against the well-known LEACH and CELRP protocols. The outcomes show a significant improvement in the WSN in terms of energy efficiency and the overall performance of WSN.

  17. Minimum Energy Dwelling (MED) workbook: an investigation of techniques and materials for energy conscious design

    Energy Technology Data Exchange (ETDEWEB)

    1977-12-01

    This workbook is based upon information gathered during the design phase of the Minimum Energy Dwelling. The objective of the project, sponsored by the Southern California Gas Co., Department of Energy, and Mission Viejo is to substantially reduce energy use by the incorporation of energy conservation and solar techniques in a single-family detached dwelling. The Project will demonstrate to builders, as well as to the general public, a number of technological innovations that can, at reasonable cost, be included in a dwelling design. The problem facing Southern California Gas Co., along with most other gas utilities, is ever-decreasing amounts of gas at increasing prices. The dwelling designed has approximately 1,150 ft/sup 2/, consistent with current home-building trends. Through the optimum use of energy-conserving appliances, insulation, window and wall shading, exterior coloring, and thermal mass, the yearly energy usage has been reduced by over 50%. Of the remaining 50% of the energy required for heating, cooling, and domestic hot water, the majority is supplied by the solar-energy system. Three hundred twenty square feet (270 effective) of evacuated tube collector are incorporated into the building structure. The hot water provided by the collectors is used to run an absorption chiller for cooling, the domestic hot water, and the heating system. The remaining energy requirements are met by an auxiliary natural gas energy system and a cool-air-economizer cycle.

  18. Energy efficient neural stimulation: coupling circuit design and membrane biophysics.

    Directory of Open Access Journals (Sweden)

    Thomas J Foutz

    Full Text Available The delivery of therapeutic levels of electrical current to neural tissue is a well-established treatment for numerous indications such as Parkinson's disease and chronic pain. While the neuromodulation medical device industry has experienced steady clinical growth over the last two decades, much of the core technology underlying implanted pulse generators remain unchanged. In this study we propose some new methods for achieving increased energy-efficiency during neural stimulation. The first method exploits the biophysical features of excitable tissue through the use of a centered-triangular stimulation waveform. Neural activation with this waveform is achieved with a statistically significant reduction in energy compared to traditional rectangular waveforms. The second method demonstrates energy savings that could be achieved by advanced circuitry design. We show that the traditional practice of using a fixed compliance voltage for constant-current stimulation results in substantial energy loss. A portion of this energy can be recuperated by adjusting the compliance voltage to real-time requirements. Lastly, we demonstrate the potential impact of axon fiber diameter on defining the energy-optimal pulse-width for stimulation. When designing implantable pulse generators for energy efficiency, we propose that the future combination of a variable compliance system, a centered-triangular stimulus waveform, and an axon diameter specific stimulation pulse-width has great potential to reduce energy consumption and prolong battery life in neuromodulation devices.

  19. Technical Support Document: Development of the Advanced Energy Design Guide for Grocery Stores--50% Energy Savings

    Energy Technology Data Exchange (ETDEWEB)

    Hale, E. T.; Macumber, D. L.; Long, N. L.; Griffith, B. T.; Benne, K. S.; Pless, S. D.; Torcellini, P. A.

    2008-09-01

    This report provides recommendations that architects, designers, contractors, developers, owners, and lessees of grocery store buildings can use to achieve whole-building energy savings of at least 50% over ASHRAE Standard 90.1-2004.

  20. Laser Intertial Fusion Energy: Neutronic Design Aspects of a Hybrid Fusion-Fission Nuclear Energy System

    Energy Technology Data Exchange (ETDEWEB)

    Kramer, Kevin James [Univ. of California, Berkeley, CA (United States)

    2010-04-08

    This study investigates the neutronics design aspects of a hybrid fusion-fission energy system called the Laser Fusion-Fission Hybrid (LFFH). A LFFH combines current Laser Inertial Confinement fusion technology with that of advanced fission reactor technology to produce a system that eliminates many of the negative aspects of pure fusion or pure fission systems. When examining the LFFH energy mission, a significant portion of the United States and world energy production could be supplied by LFFH plants. The LFFH engine described utilizes a central fusion chamber surrounded by multiple layers of multiplying and moderating media. These layers, or blankets, include coolant plenums, a beryllium (Be) multiplier layer, a fertile fission blanket and a graphite-pebble reflector. Each layer is separated by perforated oxide dispersion strengthened (ODS) ferritic steel walls. The central fusion chamber is surrounded by an ODS ferritic steel first wall. The first wall is coated with 250-500 μm of tungsten to mitigate x-ray damage. The first wall is cooled by Li17Pb83 eutectic, chosen for its neutron multiplication and good heat transfer properties. The Li17Pb83 flows in a jacket around the first wall to an extraction plenum. The main coolant injection plenum is immediately behind the Li17Pb83, separated from the Li17Pb83 by a solid ODS wall. This main system coolant is the molten salt flibe (2LiF-BeF2), chosen for beneficial neutronics and heat transfer properties. The use of flibe enables both fusion fuel production (tritium) and neutron moderation and multiplication for the fission blanket. A Be pebble (1 cm diameter) multiplier layer surrounds the coolant injection plenum and the coolant flows radially through perforated walls across the bed. Outside the Be layer, a fission fuel layer comprised of depleted uranium contained in Tristructural-isotropic (TRISO) fuel particles

  1. Designing an energy-efficient quick service restaurant

    Energy Technology Data Exchange (ETDEWEB)

    Young, R.; Spata, A.J.; Turnbull, P.; Allen, T.E.

    1999-07-01

    Food service operators typically focus on controlling labor and food costs in order to increase profits. Energy, which typically represents 2% to 6% of the total cost to operate, is often a lower priority due to the complexity of food service operations and the lack of practical information. However, in an increasing competitive market, operators are actively seeking opportunities to further reduce overhead, and energy represents a good candidate. This paper presents an overview of the design and application of energy-efficient technologies to a quick service restaurant (QSR) and the resulting energy savings. Included in the discussion are the relevance of energy efficiency in a QSR, the criteria for choosing appropriate energy-efficient technologies, the replication of results to other restaurants, and the performance of the individual energy-saving technologies. Three different techniques were used to estimate energy savings of the energy-efficient technologies, with results in the range of 12% to 18% savings in overall annual restaurant energy costs.

  2. Commercial building design and energy conservation: a preliminary assessment

    Energy Technology Data Exchange (ETDEWEB)

    Nieves, A.; Rosoff, D.

    1982-02-01

    The purpose of the research was to determine the degree of change in commercial building design practice relating to energy conservation since the enactment of the Energy Conservation Standard for New Buildings Act of 1976. Data on current design practices consisted of information from 400 buildings advertised for bids or under construction in 1979 to 1980 on glass in windows and doors, exterior wall systems, roof system, heating plants, and lighting systems. In addition to these building design components, energy conservation measures used included: natural lighting; deadband thermostat; greenhouse-effect atrium collector, heat recovery from the top of the atrium, greenhouse passive heating panels; natural ventilation; insulating shutters, closable skylights, thermal shutters, Trombe wall, corridor trombe; attic ventilation; wind shielding, concrete wall; titlted windows; night flushing cycle; and cooling coils using cooling tower water. A brief explanation of these measures is given. (MCW)

  3. Integrated Circuit Design in US High-Energy Physics

    CERN Document Server

    De Geronimo, G; Bebek, C; Garcia-Sciveres, M; Von der Lippe, H; Haller, G; Grillo, A A; Newcomer, M

    2013-01-01

    This whitepaper summarizes the status, plans, and challenges in the area of integrated circuit design in the United States for future High Energy Physics (HEP) experiments. It has been submitted to CPAD (Coordinating Panel for Advanced Detectors) and the HEP Community Summer Study 2013(Snowmass on the Mississippi) held in Minnesota July 29 to August 6, 2013. A workshop titled: US Workshop on IC Design for High Energy Physics, HEPIC2013 was held May 30 to June 1, 2013 at Lawrence Berkeley National Laboratory (LBNL). A draft of the whitepaper was distributed to the attendees before the workshop, the content was discussed at the meeting, and this document is the resulting final product. The scope of the whitepaper includes the following topics: Needs for IC technologies to enable future experiments in the three HEP frontiers Energy, Cosmic and Intensity Frontiers; Challenges in the different technology and circuit design areas and the related R&D needs; Motivation for using different fabrication technologies...

  4. New Strategy of IPACS Design and Energy Management for Spacecrafts

    Institute of Scientific and Technical Information of China (English)

    ZHANG Jing-rui

    2006-01-01

    The design problem of an integrated power and attitude control system (IPACS) for spacecrafts is investigated. A Lyapunov-typed IPACS controller is designed for a spacecraft equipped with 4 flywheels (3 orthogonal + 1 skew). This controller keeps in the nonlinear properties of original systems, so the control result can be more precise. A control law of the flywheels is also proposed to accomplish the attitude control and energy storage simultaneously. Aiming at the limitations existing in the power conversion characteristic and the wheel's motor, a new strategy of energy management is proposed. The strategy can not only make the charged/discharged energy reaching balance in each orbital period, but also sufficiently utilize the power provided by the solar arrays. Therefore, the size and mass of solar arrays can be decreased, and the cost of spacecraft can be economized. A simulation example illustrates the validity of the designed IPACS.

  5. The effect of calculated explosive energy output on blast design

    Energy Technology Data Exchange (ETDEWEB)

    Katsabanis, P.D.; Workman, L.

    1996-12-31

    The energy output of an explosive is typically calculated using an equation of state and computer applications. Results are reported as weight and bulk strength, either in absolute terms or relative to ANFO. The effect of the equation of state selected and the assumptions regarding the energy calculation are considered and interpreted for the purpose of blast design. It appears that variations in the heat of detonation which result from the selection of the equation of state and parameters associated with it are not sufficient to significantly affect blast patterns, explosive consumption and costs. However variations stemming from the use of available energy associated with a cut-off pressure are significant, suggesting in many cases large pattern expansions. The validity of the various approaches is discussed and blast design results based on the energy calculated by the different approaches are presented and evaluated.

  6. Hypertext Configurations

    DEFF Research Database (Denmark)

    Finnemann, Niels Ole

    2016-01-01

    , links, interactive processes, and time scalings, and that the hypertext configuration is a major but not sole source of the messiness of big data. The notion of hypertext will be revalidated, placed at the center of the interpretation of networked digital media, and used in the analysis of the fast......The article presents a conceptual framework for distinguishing different sorts of heterogeneous digital materials. The hypothesis is that a wide range of heterogeneous data resources can be characterized and classified due to their particular configurations of hypertext features such as scripts......-growing amounts of heterogeneous digital collections, assemblages, and corpora. The introduction summarizes the wider background of a fast-changing data landscape....

  7. Options for passive energy conservation in site design

    Energy Technology Data Exchange (ETDEWEB)

    Robinette, Gary O.; Irons, Lynda; Roth, Ann; Felix, Carol; Reimann, Robert; Buechner, Stephan; Crandall, David B.; Paulo, Frances X.; Curry, George; Balsely, Douglas; Frecericks, Regina; Wilensky, Varda; Needham, Roberta

    1978-06-01

    At a time of concern for energy supplies and costs it is essential to examine the energy-conserving potential of once again using natural energy systems and patterns that exist on any site on which a building is to be or has been placed. This state-of-the-art study examines existing research and applications of land planning and design for energy-conservation purposes. It is organized around the basic principles of natural heating and cooling factors and the impact of site elements on human comfort, regional adaptation of these principles, steps in the site planning and design process, and energy-conservation options available in each of the steps. This is supplemented by an appendix and a bibliography of additional references. The principles of site planning and design for energy conservation deal with the impact of the sun and wind on natural elements and, conversely, ways in which landforms, water, and vegetation affect the impact of the sun and wind on limited sections of the earth. For instance, the sun is able to naturally warm certain slopes more than others, certain surface materials naturally accentuate the warmth of the sun, while certain naturally occurring elements, such as vegetation, block and control the sun. The wind moving over the earth's surface has certain natural directions, patterns, and characteristics. By recognizing these and by introducing or removing impediments it is possible to modify these patterns to provide natural ventilation and to conserve energy. Four commonly accepted regional divisions were utilized to illustrate the differing applications of these principles in the temperate, hot-humid, hot-arid, and cool regions of the continental U.S. The typical site planning or design process was superimposed over each region to illustrate the various energy conservation options possible, depending upon the precise decision made in each step in each region. 300 references.

  8. Economic and environmental analysis of four different configurations of anaerobic digestion for food waste to energy conversion using LCA for: a food service provider case study.

    Science.gov (United States)

    Franchetti, Matthew

    2013-07-15

    The US disposes of more than 34 million tons of food waste in landfills per year. As this food waste decomposes it generates methane gas and negatively contributes to global warming. Diverting theses organic food wastes from landfills and to emerging technologies will prevent these wastes and greenhouse gas emissions while at the same time generating a source renewable energy by collecting the emitted gases. From a waste prevention standpoint, instead of the food waste decomposing at local landfills, it is being converted into an energy source and the by-product may be used as a fertilizer (Fine and Hadas, 2012). The purpose of this study was to compare four different configurations of anaerobic digestion of organic waste to energy technologies from an economic, energy, and emissions standpoint using LCA via a case study at a large food services provider in Northwest Ohio, USA. The technologies studied included two-stage anaerobic digestion system using ultrasound pre-treating, two stage continuous combined thermophilic acidogenic hydrogenesis and mesophilic with recirculation of the digested sludge, long-term anaerobic digestion of food waste stabilized by trace elements, and single stage anaerobic digestion. Using LCA, these scenarios were compared to landfill disposal of the food waste. The findings from the case study indicated that implementing on-site waste to energy systems will result in lower operation costs and lower environmental impacts. In addition, a standardized environmental and economic comparison of competing food waste to energy technologies is provided. Copyright © 2013 Elsevier Ltd. All rights reserved.

  9. Energy-landscape Nexus: Advancing a conceptual framework for the design of sustainable energy landscapes

    NARCIS (Netherlands)

    Stremke, S.

    2013-01-01

    For some time now, the concept of “energy landscape” is discussed in academia while more and more practising landscape architects contribute to the siting, designing, and assessment of renewable energy technologies (see Stremke et al. 2012). Yet, there remains some ambiguity what exactly is meant wi

  10. Power inversion design for ocean wave energy harvesting

    Science.gov (United States)

    Talebani, Anwar N.

    The needs for energy sources are increasing day by day because of several factors, such as oil depletion, and global climate change due to the higher level of CO2, so the exploration of various renewable energy sources is very promising area of study. The available ocean waves can be utilized as free source of energy as the water covers 70% of the earth surface. This thesis presents the ocean wave energy as a source of renewable energy. By addressing the problem of designing efficient power electronics system to deliver 5 KW from the induction generator to the grid with less possible losses and harmonics as possible and to control current fed to the grid to successfully harvest ocean wave energy. We design an AC-DC full bridge rectifier converter, and a DC-DC boost converter to harvest wave energy from AC to regulated DC. In order to increase the design efficiency, we need to increase the power factor from (0.5-0.6) to 1. This is accomplished by designing the boost converter with power factor correction in continues mode with RC circuit as an input to the boost converter power factor correction. This design results in a phase shift between the input current and voltage of the full bridge rectifier to generate a small reactive power. The reactive power is injected to the induction generator to maintain its functionality by generating a magnetic field in its stator. Next, we design a single-phase pulse width modulator full bridge voltage source DC-AC grid-tied mode inverter to harvest regulated DC wave energy to AC. The designed inverter is modulated by inner current loop, to control current injected to the grid with minimal filter component to maintain power quality at the grid. The simulation results show that our design successfully control the current level fed to the grid. It is noteworthy that the simulated efficiency is higher than the calculated one since we used an ideal switch in the simulated circuit.

  11. Zero Energy Schools: Designing for the Future: Zero Energy Ready K-12 Schools

    Energy Technology Data Exchange (ETDEWEB)

    Torcellini, Paul A [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

    2017-09-29

    Designing, building, and operating zero energy ready K-12 schools provides benefits for districts, students, and teachers. Optimizing energy efficiency is important in any building, but it's particularly important in K-12 schools. Many U.S. school districts struggle for funding, and improving a school building's energy efficiency can free up operational funds that may then be available for educational and other purposes.

  12. Ocean Thermal Energy Conservation (OTEC) power system development (PDS) II. Preliminary design report

    Energy Technology Data Exchange (ETDEWEB)

    1979-08-10

    This report documents the results and conclusions of the PDS II, Phase I, preliminary design of a 10 MWe OTEC power system, using enhanced plate type heat exchangers, and of representative 0.2 MWe test articles. It further provides the documentation (specifications, drawings, trade studies, etc.) resulting from the design activities. The data and discussions of the technical concepts are organized to respond to the PDS II, Phase II proposal evaluation criteria. This volume, which specifically addresses the three evaluation categories (heat exchangers, rotating machinery, and power system configuration and performance) is an integral part of the Phase II plans (proposal) which describe the technical approach to delivering test articles to OTEC-1. In addition, there is a section which addresses power system cost and net energy analysis and another which discusses the results of stainless steel feasibility studies. Supporting documentation is contained in two appendix volumes.

  13. Energy savings solutions: passive solar design in Iranian cold climate

    Energy Technology Data Exchange (ETDEWEB)

    Nassehzadeh Tabriz, Shahram [Department of Architecture, Miyaneh Branch, Islamic Azad University (Iran, Islamic Republic of)], email: sh_nassehzadeh@m-iau.ac.ir; Mahdavi Tabatabaei Fard, Fariborz [SABAT TARH CO. (Iran, Islamic Republic of)], email: sabat_arc@yahoo.com; Aliyev, Fagan [International Eco-energy Academy (Azerbaijan)], email: ie_academy@yahoo.com

    2011-07-01

    In recent years, there has been a significant increase in the cost of fuel gas, fuel oil and electricity and much thought has been given to the use of solar energy. Living in a solar heated house gives peace of mind and body and it makes good sense in mountainous regions. Severe winters in such regions make more energy for standard living activities in buildings necessary. This paper discusses passive solar building design as an energy saving solution. In this type of design, windows, walls and floors act as storage and distribution devices for solar energy in winter and deflect solar heat in summer. Passive solar design techniques influence the choice of building site, design and materials within the general framework of enriching the quality of life of the inhabitants. As a result, natural resources are saved and the environment is conserved for future generations. In conclusion, it is seen that passive design keeps a home cool and comfortable in summer and warm and cozy in winter with minimal heating and cooling requirements.

  14. 一种可配置Schmitt trigger IO设计%Design of a configurable Schmitt trigger IO

    Institute of Scientific and Technical Information of China (English)

    张健; 胥志毅; 邬天凯; 刘文江; 刘斌; 季千惠

    2012-01-01

    The application of electromagnetic environment of electronic devices in national defense equipment is extremely complex because the temperature and the working voltage are always fluctuating. Schmitt trigger 10 performs very well on these anti-noise problems of 10. Noise intensity varies in different application environment. In some cases the noise of high level signal is larger; in other cases the noise of low level signal is larger. A configurable Schmitt trigger 10, whose VIH and VFL can be configured independently, can help a chip to adapt to different noise interference in different environment through configuring different VIH and VIL.%国防设备中使用的各种电子器件通常面临着极其复杂的电磁环境,其特点是温度变化比较大,工作电压波动大.噪声干扰会在很大程度上影响这些器件的工作.Schmitt trigger IO可以有效地解决这种复杂环境中IO的抗噪声问题.不同的应用环境中,相同的IO面临的噪声强度也不相同,有些环境中高电平的噪声大,有些环境中低电平噪声大.因此,一种可配置的、可单独调整VIH和VIL的Schmitt trigger IO可以满足单一芯片在不同应用环境中适应不同噪声干扰的要求.

  15. Design for energy efficiency: Energy efficient industrialized housing research program. Progress report

    Energy Technology Data Exchange (ETDEWEB)

    Kellett, R.; Berg, R.; Paz, A.; Brown, G.Z.

    1991-03-01

    Since 1989, the U.S. Department of Energy has sponsored the Energy Efficient Industrialized Housing research program (EEIH) to improve the energy efficiency of industrialized housing. Two research centers share responsibility for this program: The Center for Housing Innovation at the University of Oregon and the Florida Solar Energy Center, a research institute of the University of Central Florida. Additional funding is provided through the participation of private industry, state governments and utilities. The program is guided by a steering committee comprised of industry and government representatives. This report summarizes Fiscal Year (FY) 1990 activities and progress, and proposed activities for FY 1991 in Task 2.1 Design for Energy Efficiency. This task establishes a vision of energy conservation opportunities in critical regions, market segments, climate zones and manufacturing strategies significant to industrialized housing in the 21st Century. In early FY 1990, four problem statements were developed to define future housing demand scenarios inclusive of issues of energy efficiency, housing design and manufacturing. Literature surveys were completed to assess seven areas of influence for industrialized housing and energy conservation in the future. Fifty-five future trends were identified in computing and design process; manufacturing process; construction materials, components and systems; energy and environment; demographic context; economic context; and planning policy and regulatory context.

  16. The LHCb configuration database

    CERN Document Server

    Abadie, Lana; Gaspar, Clara; Jacobsson, Richard; Jost, Beat; Neufeld, Niko

    2005-01-01

    The Experiment Control System (ECS) will handle the monitoring, configuration and operation of all the LHCb experimental equipment. All parameters required to configure electronics equipment under the control of the ECS will reside in a configuration database. The database will contain two kinds of information: 1.\tConfiguration properties about devices such as hardware addresses, geographical location, and operational parameters associated with particular running modes (dynamic properties). 2.\tConnectivity between devices : this consists of describing the output and input connections of a device (static properties). The representation of these data using tables must be complete so that it can provide all the required information to the ECS and must cater for all the subsystems. The design should also guarantee a fast response time, even if a query results in a large volume of data being loaded from the database into the ECS. To fulfil these constraints, we apply the following methodology: Determine from the d...

  17. Fluid manifold design for a solar energy storage tank

    Science.gov (United States)

    Humphries, W. R.; Hewitt, H. C.; Griggs, E. I.

    1975-01-01

    A design technique for a fluid manifold for use in a solar energy storage tank is given. This analytical treatment generalizes the fluid equations pertinent to manifold design, giving manifold pressures, velocities, and orifice pressure differentials in terms of appropriate fluid and manifold geometry parameters. Experimental results used to corroborate analytical predictions are presented. These data indicate that variations in discharge coefficients due to variations in orifices can cause deviations between analytical predictions and actual performance values.

  18. Design tools for daylighting illumination and energy analysis

    Energy Technology Data Exchange (ETDEWEB)

    Selkowitz, S.

    1982-07-01

    The problems and potentials for using daylighting to provide illumination in building interiors are reviewed. It describes some of the design tools now or soon to be available for incorporating daylighting into the building design process. It also describes state-of-the-art methods for analyzing the impacts daylighting can have on selection of lighting controls, lighting energy consumption, heating and cooling loads, and peak power demand.

  19. Facade Refurbishment Toolbox. Supporting the Design of Residential Energy Upgrades

    Directory of Open Access Journals (Sweden)

    Thaleia Konstantinou

    2014-07-01

    Full Text Available The starting point of the research is the need to refurbish existing residential building stock, in order to reduce its energy demand, which accounts for over one fourth of the energy consumption in the European Union. Refurbishment is a necessary step to reach the ambitious energy and decarbonisation targets for 2020 and 2050 that require an eventual reduction up to 90% in CO2 emissions. In this context, the rate and depth of refurbishment need to grow. The number of building to be renovated every year should increase, while the energy savings in renovated buildings should be over 60% reduction to current energy demand. To achieve that, not only is it necessary to find politics and incentives, but also to enable the building industry to design and construct effective refurbishment strategies. This research focuses on refurbishment of the building envelope, as it is very influential with regard to energy reduction.The early design phases are particularly important, as decisions taken during this stage can determine the success or failure of the design. Even though the design decisions made earlier can have bigger impact with lower cost and effort, most existing tools focus on post-design evaluation. The integration of all aspects during the early design phases is complex, particularly as far as energy efficient design is concerned. At this stage, architects are in search for a design direction to make an informed decision. If the designer is provided with an indication of how efficient refurbishment options are, it is possible to apply them as part of an integrated strategy rather than trying to add measures at later stages, after the strategy has been developed.Therefore, taking into account the need to refurbish residential buildings and the importance of integrated design of façade refurbishment strategies, the thesis aims at answering the following question.How can the energy upgrade potential of residential façade refurbishment strategies

  20. Design of energy-based terrain following flight control system

    Science.gov (United States)

    Wang, Wei; Li, Aijun; Xie, Yanwu; Tan, Jian

    2006-11-01

    Historically, aircraft longitudinal control has been realized by means of two loops: flight path (the control variable is elevator displacement) and speed control (the control variable is propulsive thrust or engine power). Both the elevator and throttle control cause coupled altitude and speed response, which exerts negative effects on longitudinal flight performance of aircraft, especially for Terrain Following(TF) flight. Energy-based method can resolve coupled problem between flight speed and path by controlling total energy rate and energy distribution rate between elevator and throttle. In this paper, energy-based control method is applied to design a TF flight control system for controlling flight altitude directly. An error control method of airspeed and altitude is adopted to eliminate the stable error of the total energy control system when decoupling control. Pitch loop and pitch rate feedback loop are designed for the system to damp the oscillatory response produced by TF system. The TF flight control system structure diagram and an aircraft point-mass energy motion model including basic control loops are given and used to simulate decoupling performance of the TF fight control system. Simulation results show that the energy-based TF flight control system can decouple flight velocity and flight path angle, exactly follow planned flight path, and greatly reduce altitude error, which is between +10m and -8m.

  1. Buildings energy management program workshop design. Final report

    Energy Technology Data Exchange (ETDEWEB)

    None

    1978-12-01

    This document describes activities undertaken by Honeywell's Energy Resources Center for design and development of the format, content, and materials that were used in conducting 129 one-day energy management workshops for specific commercial business audiences. The Building Energy Management Workshop Program was part of a National Workshop Program that was intended to increase awareness of energy-related issues and to encourage energy-conservation actions on the part of commercial and industrial sectors. The total effort included executive conferences for chief executive officers and other senior management personnel; industrial energy-conservation workshops directed at plant management and engineering personnel; vanpooling workshops designed to inform and encourage business in implementing a vanpooling program for employees; and the building energy-management workshops specifically developed for managers, owners, and operators of office and retail facilities, restaurants, and supermarkets. The total program spanned nearly two years and reached approximately 2,500 participants from all parts of the U.S. A detailed followup evaluation is still being conducted to determine the impact of this program in terms of conservation action undertaken by workshop participants.

  2. Evolutionary algorithm based configuration interaction approach

    CERN Document Server

    Chakraborty, Rahul

    2016-01-01

    A stochastic configuration interaction method based on evolutionary algorithm is designed as an affordable approximation to full configuration interaction (FCI). The algorithm comprises of initiation, propagation and termination steps, where the propagation step is performed with cloning, mutation and cross-over, taking inspiration from genetic algorithm. We have tested its accuracy in 1D Hubbard problem and a molecular system (symmetric bond breaking of water molecule). We have tested two different fitness functions based on energy of the determinants and the CI coefficients of determinants. We find that the absolute value of CI coefficients is a more suitable fitness function when combined with a fixed selection scheme.

  3. Numerical and experimental design of coaxial shallow geothermal energy systems

    Science.gov (United States)

    Raghavan, Niranjan

    Geothermal Energy has emerged as one of the front runners in the energy race because of its performance efficiency, abundance and production competitiveness. Today, geothermal energy is used in many regions of the world as a sustainable solution for decreasing dependence on fossil fuels and reducing health hazards. However, projects related to geothermal energy have not received their deserved recognition due to lack of computational tools associated with them and economic misconceptions related to their installation and functioning. This research focuses on numerical and experimental system design analysis of vertical shallow geothermal energy systems. The driving force is the temperature difference between a finite depth beneath the earth and its surface stimulates continuous exchange of thermal energy from sub-surface to the surface (a geothermal gradient is set up). This heat gradient is captured by the circulating refrigerant and thus, tapping the geothermal energy from shallow depths. Traditionally, U-bend systems, which consist of two one-inch pipes with a U-bend connector at the bottom, have been widely used in geothermal applications. Alternative systems include coaxial pipes (pipe-in-pipe) that are the main focus of this research. It has been studied that coaxial pipes have significantly higher thermal performance characteristics than U-bend pipes, with comparative production and installation costs. This makes them a viable design upgrade to the traditional piping systems. Analytical and numerical heat transfer analysis of the coaxial system is carried out with the help of ABAQUS software. It is tested by varying independent parameters such as materials, soil conditions and effect of thermal contact conductance on heat transfer characteristics. With the above information, this research aims at formulating a preliminary theoretical design setup for an experimental study to quantify and compare the heat transfer characteristics of U-bend and coaxial

  4. Configuration of Green Spaces for Urban Heat Island Mitigation and Future Building Energy Conservation in Hanoi Master Plan 2030

    Directory of Open Access Journals (Sweden)

    Andhang Rakhmat Trihamdani

    2015-08-01

    Full Text Available The study aims to assess the urban heat island (UHI effects in the city under the present land use conditions as well as those conditions proposed by the Hanoi Master Plan 2030 through numerical simulation, using Weather Research and Forecasting (WRF. Furthermore, this paper assesses additional land use scenarios with different spatial and green space configurations. The results show that the implementation of the master plan does not significantly affect the peak air temperature in the built-up areas (approximately 1 °C higher at the maximum. However, high temperature areas, with temperature of 40–41 °C, would expand widely over the new built-up areas. On the other hand, the nocturnal air temperature would increase by up to 2–3 °C over the newly expanded built-up areas. The number of hotspots increased further when the strategic green spaces in the master plan were not taken into account. However, the cooling effect of the strategic green spaces did not reach the existing city center sufficiently because the green spaces are located far from the city center. The large and centralized green spaces proposed in the master plan were seen to be insufficient to mitigate UHIs compared to the equally distributed green spaces. Moreover, the greater reduction of hotspot areas by up to 56.5% was seen when the mixed forest is employed as the land cover in the green spaces.

  5. Solar Energy: Progress and Design Concerns of Nanostructured Solar Energy Harvesting Devices (Small 19/2016).

    Science.gov (United States)

    Leung, Siu-Fung; Zhang, Qianpeng; Tavakoli, Mohammad Mahdi; He, Jin; Mo, Xiaoliang; Fan, Zhiyong

    2016-05-01

    Nanoengineered materials and structures can harvest light efficiently for photovoltaic applications. Device structure design optimization and material property improvement are equally important for high performance. On page 2536, X. Mo, Z. Fan, and co-workers summarize the design guidelines of solar energy harvesting devices to assist with a better understanding of device physics.

  6. A Novel Method for Fast Configuration of Energy Storage Capacity in Stand-Alone and Grid-Connected Wind Energy Systems

    Directory of Open Access Journals (Sweden)

    Haixiang Zang

    2016-12-01

    Full Text Available In this paper, a novel method is proposed and applied to quickly calculate the capacity of energy storage for stand-alone and grid-connected wind energy systems, according to the discrete Fourier transform theory. Based on practical wind resource data and power data, which are derived from the American Wind Energy Technology Center and HOMER software separately, the energy storage capacity of a stand-alone wind energy system is investigated and calculated. Moreover, by applying the practical wind power data from a wind farm in Fujian Province, the energy storage capacity for a grid-connected wind system is discussed in this paper. This method can also be applied to determine the storage capacity of a stand-alone solar energy system with practical photovoltaic power data.

  7. Multi objective decision making in hybrid energy system design

    Science.gov (United States)

    Merino, Gabriel Guillermo

    The design of grid-connected photovoltaic wind generator system supplying a farmstead in Nebraska has been undertaken in this dissertation. The design process took into account competing criteria that motivate the use of different sources of energy for electric generation. The criteria considered were 'Financial', 'Environmental', and 'User/System compatibility'. A distance based multi-objective decision making methodology was developed to rank design alternatives. The method is based upon a precedence order imposed upon the design objectives and a distance metric describing the performance of each alternative. This methodology advances previous work by combining ambiguous information about the alternatives with a decision-maker imposed precedence order in the objectives. Design alternatives, defined by the photovoltaic array and wind generator installed capacities, were analyzed using the multi-objective decision making approach. The performance of the design alternatives was determined by simulating the system using hourly data for an electric load for a farmstead and hourly averages of solar irradiation, temperature and wind speed from eight wind-solar energy monitoring sites in Nebraska. The spatial variability of the solar energy resource within the region was assessed by determining semivariogram models to krige hourly and daily solar radiation data. No significant difference was found in the predicted performance of the system when using kriged solar radiation data, with the models generated vs. using actual data. The spatial variability of the combined wind and solar energy resources was included in the design analysis by using fuzzy numbers and arithmetic. The best alternative was dependent upon the precedence order assumed for the main criteria. Alternatives with no PV array or wind generator dominated when the 'Financial' criteria preceded the others. In contrast, alternatives with a nil component of PV array but a high wind generator component

  8. Designing and Testing Energy Harvesters Suitable for Renewable Power Sources

    Science.gov (United States)

    Synkiewicz, B.; Guzdek, P.; Piekarski, J.; Zaraska, K.

    2016-01-01

    Energy harvesters convert waste power (heat, light and vibration) directly to electric power . Fast progress in their technology, design and areas of application (e.g. “Internet of Things”) has been observed recently. Their effectiveness is steadily growing which makes their application to powering sensor networks with wireless data transfer reasonable. The main advantage is the independence from wired power sources, which is especially important for monitoring state of environmental parameters. In this paper we describe the design and realization of a gas sensor monitoring CO level (powered by TEG) and two, designed an constructed in ITE, autonomous power supply modules powered by modern photovoltaic cells.

  9. Design of an energy-efficient CNFET Full Adder Cell

    Directory of Open Access Journals (Sweden)

    Arezoo Taeb

    2012-05-01

    Full Text Available In this paper by using the carbon nanotube field effect transistor (CNFET, which is a promising alternative for the MOSFET transistor, two novel energy-efficient Full Adders are proposed. The proposed Full Adders show full swing logic and strong output drivability. The first design uses eight transistors and nine capacitors and the second design utilizes three capacitors less than the first design. Simulations, carried out using HSPICE based on the Stanford University CNFET model at 0.6V and 0.9V supply voltages, demonstrate the efficiency of type proposed circuit parameters such as delay, power and power-delay product.

  10. Early Design Energy Analysis Using Building Information Modeling Technology

    Science.gov (United States)

    2011-11-01

    the Community Emergency Services Station charrette clearly showed the design intent to the customer , but the spaces were not consistently...ARCHiPHISIK and RIUSKA). Custom parametric ob- jects are primarily defined using the GDL (Geometric Description Lan- guage) scripting language, which...US Department of Energy, Victoria University of Wellington, and DHL Consulting. Ninth International IBPSA Conference: Montreal. August 15-18

  11. Good habit of energy conscious design: Bournemouth hospital

    Energy Technology Data Exchange (ETDEWEB)

    Hutchison, D.

    1987-10-01

    An expanding architectural practice is described. The substantial proportion of their workload in the Health Service and current involvement in ten major Hospital projects is outlined, as well as numerous meaningful schemes in supporting spheres such as Geriatric, Extra Frail, Mentally Handicapped and Hospice Care.. Their approach to energy considerations in design is examined.

  12. Best Practices Guide for Energy-Efficient Data Center Design

    Energy Technology Data Exchange (ETDEWEB)

    O. VanGeet: NREL

    2010-02-24

    This guide provides an overview of best practices for energy-efficient data center design which spans the categories of Information Technology (IT) systems and their environmental conditions, data center air management, cooling and electrical systems, on-site generation, and heat recovery.

  13. Design tool for the thermal energy potential of asphalt pavements

    NARCIS (Netherlands)

    Loomans, M.G.L.C.; Oversloot, H.P.; Bondt, A. de; Jansen, R.; Rij, H. van

    2003-01-01

    This paper describes the development of a design tool for the calculation of the thermal energy potential of a so-called asphalt collector. Two types of numerical models have been developed and validated against experimental results from a full-scale test-site. The validation showed to be a tedious

  14. Optimal Design of RF Energy Harvesting Device Using Genetic Algorithm

    Science.gov (United States)

    Mori, T.; Sato, Y.; Adriano, R.; Igarashi, H.

    2015-11-01

    This paper presents optimal design of an RF energy harvesting device using genetic algorithm (GA). In the present RF harvester, a planar spiral antenna (PSA) is loaded with matching and rectifying circuits. On the first stage of the optimal design, the shape parameters of PSA are optimized using . Then, the equivalent circuit of the optimized PSA is derived for optimization of the circuits. Finally, the parameters of RF energy harvesting circuit are optimized to maximize the output power using GA. It is shown that the present optimization increases the output power by a factor of five. The manufactured energy harvester starts working when the input electric field is greater than 0.5 V/m.

  15. Enhanced energy density of a supercapacitor using 2D CoMoO4 ultrathin nanosheets and asymmetric configuration

    Science.gov (United States)

    Zhao, Yunxuan; Liu, Zailun; Gu, Wenhao; Zhai, Yifei; Teng, Yiran; Teng, Fei

    2016-12-01

    Developing a high energy density micro-supercapacitor still remains a big challenge. In this paper, a two-dimensional (2D) CoMoO4 ultrathin nanosheet (NS)-based asymmetric supercapacitor (ASC) is fabricated. It is found that the CoMoO4 NS electrode processes a high specific capacitance (153.2 F g-1) at a current density of 1 mA cm-2 and this ASC can deliver an energy density of 0.313 mWh cm-3 at a power density of 80 mW cm-3, which is higher than that reported in the literature. Moreover, the ASC can drive a light emitting diode (3 mm diameter, red) to work for 6 min after being charged for 10 s. After 5000 cycles, 77.37% of capacitance still remains. We maintain that the ultrathin thickness can significantly shorten the diffusion paths for both electrons and ions, thus leading to fast electron transport and ion diffusion rates. Our results demonstrate that 2D ultrathin NSs could be a new, promising candidate for energy conversion/storage devices, which could offer more accommodating sites for ion intercalation.

  16. A new (multi-reference configuration interaction) potential energy surface for H2CO and preliminary studies of roaming

    Science.gov (United States)

    Wang, Xiaohong; Houston, Paul L.; Bowman, Joel M.

    2017-03-01

    We report a new global potential energy surface (PES) for H2CO, based on precise fitting of roughly 67 000 MRCI/cc-pVTZ energies. This PES describes the global minimum, the cis- and trans-HCOH isomers, and barriers relevant to isomerization, formation of the molecular (H2+CO) and radical (H+HCO) products, and the loose so-called roaming transition-state saddle point. The key features of the PES are reviewed and compared with a previous PES, denoted by PES04, based on five local fits that are `stitched' together by switching functions (Zhang et al. 2004 J. Phys. Chem. A 108, 8980-8986 (doi:10.1021/jp048339l)). Preliminary quasi-classical trajectory calculations are performed at the total energy of 36 233 cm-1 (103 kcal mol-1), relative to the H2CO global minimum, using the new PES, with a particular focus on roaming dynamics. When compared with the results from PES04, the new PES findings show similar rotational distributions, somewhat more roaming and substantially higher H2 vibrational excitation. This article is part of the themed issue 'Theoretical and computational studies of non-equilibrium and non-statistical dynamics in the gas phase, in the condensed phase and at interfaces'.

  17. Design and Fabrication of 3D Electrostatic Energy Harvester

    Directory of Open Access Journals (Sweden)

    V. Janicek

    2012-04-01

    Full Text Available This paper discusses the design of an electrostatic generator, power supply component of the self-powered microsystem, which is able to provide enough energy to power smart sensor chains or if necessary also other electronic monitoring devices. One of the requirements for this analyzer is the mobility, so designing the power supply expects use of an alternative way of getting electricity to power the device, rather than rely on periodic supply of external energy in the form of charging batteries, etc. In this case the most suitable method to use is so-called energy harvesting – a way how to gather energy. This uses the principle of non-electric conversion of energy into electrical energy in the form of converters. The present study describes the topology design of such structures of electrostatic generator. Structure is designed and modeled as a three-dimensional silicon based MEMS. Innovative approach involving the achievement of very low resonant frequency of the structure, while the minimum area of the chip, the ability to work in all 3 axes of coordinate system and ability to be tuned to reach desired parameters proves promising directions of possible further development of this issue. The work includes simulation of electro-mechanical and electrical properties of the structure, description of its behavior in different operating modes and phases of activity. Simulation results were compared with measured values of the produced prototype chip. These results can suggest possible modifications to the proposed structure for further optimization and application environment adaptation.

  18. Designing effective incentives for energy conservation in the public sector

    Science.gov (United States)

    Drezner, Jeffrey Alan

    Understanding why government officials behave in certain ways under particular circumstances is an important theme in political science. This research explores the design of policies and incentives targeted at public sector officials, in particular the use of market based policy tools in a non-market environment, and the influence of that organizational environment on the effectiveness of the policy. The research examines the case of Department of Defense (DoD) facility energy management. DoD energy policy includes a provision for the retention of savings generated by conservation activities: two-thirds of the savings is retained at the installation generating the savings, half to used for further investment in energy conservation, and half to be used for general morale, welfare, and recreation activities. This policy creates a financial incentive for installation energy managers to establish higher quality and more active conservation programs. A formal written survey of installation energy managers within DoD was conducted, providing data to test hypotheses regarding policy effectiveness and factors affecting policy implementation. Additionally, two detailed implementation case studies were conducted in order to gain further insights. Results suggest that policy design needs to account for the environment within which the policy will be implemented, particularly organizational culture and standard operating procedures. The retention of savings policy failed to achieve its intended outcome---retention of savings for re-investment in energy conservation---because the role required of the financial management community was outside its normal mode of operation and interests and the budget process for allocating resources did not include a mechanism for retention of savings. The policy design did not adequately address these start-up barriers to implementation. This analysis has shown that in order for retention of savings, or similar policies based on market

  19. Zero Energy Buildings – Design Principles and Built Examples

    DEFF Research Database (Denmark)

    Bejder, Anne Kirkegaard; Knudstrup, Mary-Ann; Jensen, Rasmus Lund

    knowledge must be acquired, depending on the project in question. Through a cross-disciplinary approach to architecture and building design, and based on an integrated design process, this publication will: • introduce a number of design strategies and technologies which are particularly important......Designing a zero energy building is a complicated task, and in order to achieve good results it is necessary to include knowledge from a range of sources. Therefore, cooperation is required between different professions and between generalists and specialists from the very beginning of the process....... The purpose of this booklet is to support the integrated design process and co-operation between different professions. The subject areas are therefore described at a general level, to provide the engineer with an insight into the techniques used by the architect, and vice versa. Additionally, specialist...

  20. Materializing a responsive interior: designing minimum energy structures

    DEFF Research Database (Denmark)

    Mossé, Aurélie; Kofod, Guggi; Ramsgaard Thomsen, Mette

    2011-01-01

    -active structures based on dielectric-elastomer, where energy-minimization and self-organization principles become central processes for the realization of shape-changing architectural surfaces. In Reef, a concept for self-actuated ceiling surface, we examine the integration of these dynamic structures...... (Lendlein, Kelch 2002) or light (van Oosten, Bastiaansen et al. 2009). All in all, this approach could form a whole new design paradigm, in which efficient 2D-manufacturing can lead to highly flexible, low weight and adaptable 3D-structures. This is illustrated by the design and manufacture of electro......This paper discusses a series of design-led experiments investigating future possibilities for architectural materialization relying on minimum energy structures as an example of adaptive structure. The structures have been made as laminates of elastic membrane under high tension with flexible...

  1. The LHCb configuration database

    CERN Document Server

    Abadie, L; Van Herwijnen, Eric; Jacobsson, R; Jost, B; Neufeld, N

    2005-01-01

    The aim of the LHCb configuration database is to store information about all the controllable devices of the detector. The experiment's control system (that uses PVSS ) will configure, start up and monitor the detector from the information in the configuration database. The database will contain devices with their properties, connectivity and hierarchy. The ability to store and rapidly retrieve huge amounts of data, and the navigability between devices are important requirements. We have collected use cases to ensure the completeness of the design. Using the entity relationship modelling technique we describe the use cases as classes with attributes and links. We designed the schema for the tables using relational diagrams. This methodology has been applied to the TFC (switches) and DAQ system. Other parts of the detector will follow later. The database has been implemented using Oracle to benefit from central CERN database support. The project also foresees the creation of tools to populate, maintain, and co...

  2. Legislative and policy in energy efficient designing and renewable energy sources: Application in Serbia

    Directory of Open Access Journals (Sweden)

    Pucar Mila

    2007-01-01

    Full Text Available This paper analyses political and legislative frames in the field of energy efficient building and renewable energy sources in planning and implementation in Serbia. „Development strategy until 2015.“ is reviewed in concise portrait. This strategy maps a way for the application of energy services of much higher quality than ones offered at a present day. It reviews relevant laws concerning the subject, as well as institutions, programs and their implementation. Basic principles of energy policy in Serbia and their achievement are also given by that strategy. Serbia's energy policies are designed to allow new legislative, structural, organizational, institutional, and economic frames and visions of unification of Serbian energetics into regional and Pan-European integrations. One of the key factors is the inclusion of sustainable development and energy efficient design concerned policies. Application of these, almost completely neglected, energy sources, for which there is high potential in Serbia, would allow preservation of primary energy sources and local environment. This potential hasn't seen significant research, and therefore, neither the technical improvement. Apart from that, one of the goals of wider application of renewable energy sources is lowering the poverty level. This helps avoiding the already used “dirty development” method. .

  3. 室内设计构成要素与配置%The Constituent Elements and Configuration of Interior Design

    Institute of Scientific and Technical Information of China (English)

    陈玲

    2015-01-01

    Stanley Abercrombie, a member of the American Institute of Architect, an honorary member of the American Interior Designer Association and the editor of Interior Design, published writings on architectural design and interior design theory, whose theory and ideas has a profound impact on interior design industry. Starting from Stanley Abercrombie's distinctive opinion of interior design, this article does not focus on the popular design style and trends, but explain the system of the basic principles of interior design and trace its source to highlight the long-term value in design.%史坦利·亚伯克隆比(Stanley Abercrombie),一位美国建筑师协会会员、美国室内设计师协会荣誉会员及《室内设计》杂志主编,出版了建筑设计、室内设计理论等著述,他的理论和思想对室内设计行业有着深远的影响.文章从史坦利·亚伯克隆比对室内设计独特的见解出发,不提倡强调当今流行的设计风格与趋势,而阐释室内设计的基本原则体系,追本溯源,以突出设计中的长久价值所在.

  4. The role of energy consciousness in the configuration and achievement of energy policy concepts. Die Rolle des Energiebewusstseins bei der Gestaltung und Durchsetzung energiepolitischer Konzeptionen

    Energy Technology Data Exchange (ETDEWEB)

    Dell, G.; Egger, C. (Oberoesterreichischer Energiesparverband, Linz (Austria))

    1992-06-01

    It is clear that in energy saving, claims and reality, above all in questions of actual implementation have previously not been brought into line. The following hypotheses form the basis for further considerations: 1. There is an existing high potential for energy savings. 2. Based on years of discussion, there is a high awareness of energy saving in the population, and 3. This consciousness and awareness do not sufficiently lead to actual action, to concrete changes of behaviour. The article describes the causes of this, ie: why the positive attitude to energy saving of society and conrete actions have not been sufficiently brought into line. (orig./UA).

  5. Electromagnetic Vibration Energy Harvesting Devices Architectures, Design, Modeling and Optimization

    CERN Document Server

    Spreemann, Dirk

    2012-01-01

    Electromagnetic vibration transducers are seen as an effective way of harvesting ambient energy for the supply of sensor monitoring systems. Different electromagnetic coupling architectures have been employed but no comprehensive comparison with respect to their output performance has been carried out up to now. Electromagnetic Vibration Energy Harvesting Devices introduces an optimization approach which is applied to determine optimal dimensions of the components (magnet, coil and back iron). Eight different commonly applied coupling architectures are investigated. The results show that correct dimensions are of great significance for maximizing the efficiency of the energy conversion. A comparison yields the architectures with the best output performance capability which should be preferably employed in applications. A prototype development is used to demonstrate how the optimization calculations can be integrated into the design–flow. Electromagnetic Vibration Energy Harvesting Devices targets the design...

  6. 长网纸机网部的节能结构设计%Energy Saving Structure Design of the Wire Part of a Fourdrinier Machine

    Institute of Scientific and Technical Information of China (English)

    李长国

    2011-01-01

    介绍了某长网纸机网部的结构配置,对该纸机的网部采用简化设计后能耗非常低.%The configuration and structure of the wire part of a fourdiinier machine are introduced, the machine features very low energy consumption due to the adoption of simplified design.

  7. Development of the Advanced Energy Design Guide for K-12 Schools -- 50% Energy Savings

    Energy Technology Data Exchange (ETDEWEB)

    Bonnema, E.; Leach, M.; Pless, S.; Torcellini, P.

    2013-02-01

    This Technical Support Document (TSD) describes the process and methodology for the development of the Advanced Energy Design Guide for K-12 School Buildings: Achieving 50% Energy Savings Toward a Net Zero Energy Building (AEDG-K12) (ASHRAE et al. 2011a). The AEDG-K12 provides recommendations for achieving 50% whole-building energy savings in K-12 schools over levels achieved by following ANSI/ASHRAE/IESNA Standard 90.1-2004, Energy Standard for Buildings Except Low-Rise Residential Buildings (Standard 90.1-2004) (ASHRAE 2004b). The AEDG-K12 was developed in collaboration with the American Society of Heating, Refrigerating and Air-Conditioning Engineers (ASHRAE), the American Institute of Architects (AIA), the Illuminating Engineering Society of North America (IES), the U.S. Green Building Council (USGBC), and the U.S. Department of Energy (DOE).

  8. Ocean Thermal Energy Conversion (OTEC) platform configuration and integration. Volume III. Development plan for demonstration unit. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Scott, R. J.

    1978-06-01

    The overall purpose of this project is the conceptual design of two OTEC commercial plants. This report presents results of task VII: a plan for the development of an OTEC Demonstration Plant including funding, key milestones, fallbacks, etc. Studies include a risk assessment survey, OTEC Demonstration Plant ocean systems requirements, OTEC Demonstration plant power and transmission system requirements, electric utility survey, market assessment, and a demonstration plan. (WHK)

  9. Configuration design and accuracy analysis of a novel magneto rheological finishing machine tool for concave surfaces with small radius of curvature

    Energy Technology Data Exchange (ETDEWEB)

    Liu, Henan; Chen, Mingjun [Harbin Institute of Technology, Harbin (China); Yu, Bo; Zhen, Fang [China Electronics Technology Group Corporation No.26 Research Institute, Chongqing (China)

    2016-07-15

    Magnetorheological finishing (MRF) is a computer-controlled deterministic polishing technique that is widely used in the production of high-quality optics. In order to overcome the defects of existing MRF processes that are unable to achieve concave surfaces with small radius of curvature, a configuration method of a novel structured MRF machine tool using small ball-end permanent-magnet polishing head is proposed in this paper. The preliminary design focuses on the structural configuration of the machine, which includes the machine body, motion units and accessory equipment, and so on. Structural deformation and fabrication accuracy of the machine are analyzed theoretically, in which the reasonable structure sizes, manufacturing errors and assembly errors of main structural components are given for configuration optimization. Based on the theoretical analysis, a four-axes linkage MRF machine tool is developed. Preliminary experiments of spot polishing are carried out and the results indicate that the proposed MRF process can achieve stable polishing area which meets requirement of deterministic polishing. A typical small-bore complex component is polished on the developed device and fine surface quality is obtained with sphericity of the finished spherical surfaces 1.3 μm and surface roughness Ra less than 0.018 μm.

  10. A detailed analysis of the energy levels configuration existing in the band gap of supersaturated silicon with titanium for photovoltaic applications

    Science.gov (United States)

    Pérez, E.; Dueñas, S.; Castán, H.; García, H.; Bailón, L.; Montero, D.; García-Hernansanz, R.; García-Hemme, E.; Olea, J.; González-Díaz, G.

    2015-12-01

    The energy levels created in supersaturated n-type silicon substrates with titanium implantation in the attempt to create an intermediate band in their band-gap are studied in detail. Two titanium ion implantation doses (1013 cm-2 and 1014 cm-2) are studied in this work by conductance transient technique and admittance spectroscopy. Conductance transients have been measured at temperatures of around 100 K. The particular shape of these transients is due to the formation of energy barriers in the conduction band, as a consequence of the band-gap narrowing induced by the high titanium concentration. Moreover, stationary admittance spectroscopy results suggest the existence of different energy level configuration, depending on the local titanium concentration. A continuum energy level band is formed when titanium concentration is over the Mott limit. On the other hand, when titanium concentration is lower than the Mott limit, but much higher than the donor impurity density, a quasi-continuum energy level distribution appears. Finally, a single deep center appears for low titanium concentration. At the n-type substrate, the experimental results obtained by means of thermal admittance spectroscopy at high reverse bias reveal the presence of single levels located at around Ec-425 and Ec-275 meV for implantation doses of 1013 cm-2 and 1014 cm-2, respectively. At low reverse bias voltage, quasi-continuously distributed energy levels between the minimum of the conduction bands, Ec and Ec-450 meV, are obtained for both doses. Conductance transients detected at low temperatures reveal that the high impurity concentration induces a band gap narrowing which leads to the formation of a barrier in the conduction band. Besides, the relationship between the activation energy and the capture cross section values of all the energy levels fits very well to the Meyer-Neldel rule. As it is known, the Meyer-Neldel rule typically appears in processes involving multiple excitations, like

  11. A detailed analysis of the energy levels configuration existing in the band gap of supersaturated silicon with titanium for photovoltaic applications

    Energy Technology Data Exchange (ETDEWEB)

    Pérez, E.; Dueñas, S.; Castán, H.; García, H.; Bailón, L. [Dept. de Electricidad y Electrónica, Universidad de Valladolid, Paseo de Belén 15, 47011 Valladolid (Spain); Montero, D.; García-Hernansanz, R.; García-Hemme, E.; González-Díaz, G. [Dept. de Física Aplicada III (Electricidad y Electrónica), Univ. Complutense de Madrid, 28040 Madrid (Spain); CEI Campus Moncloa, UCM-UPM, 28040 Madrid (Spain); Olea, J. [CEI Campus Moncloa, UCM-UPM, 28040 Madrid (Spain); Instituto de Energía Solar, E.T.S.I. de Telecomunicación, Univ. Politécnica de Madrid, 28040 Madrid (Spain)

    2015-12-28

    The energy levels created in supersaturated n-type silicon substrates with titanium implantation in the attempt to create an intermediate band in their band-gap are studied in detail. Two titanium ion implantation doses (10{sup 13 }cm{sup -2} and 10{sup 14 }cm{sup -2}) are studied in this work by conductance transient technique and admittance spectroscopy. Conductance transients have been measured at temperatures of around 100 K. The particular shape of these transients is due to the formation of energy barriers in the conduction band, as a consequence of the band-gap narrowing induced by the high titanium concentration. Moreover, stationary admittance spectroscopy results suggest the existence of different energy level configuration, depending on the local titanium concentration. A continuum energy level band is formed when titanium concentration is over the Mott limit. On the other hand, when titanium concentration is lower than the Mott limit, but much higher than the donor impurity density, a quasi-continuum energy level distribution appears. Finally, a single deep center appears for low titanium concentration. At the n-type substrate, the experimental results obtained by means of thermal admittance spectroscopy at high reverse bias reveal the presence of single levels located at around E{sub c}-425 and E{sub c}-275 meV for implantation doses of 10{sup 13 }cm{sup −2} and 10{sup 14 }cm{sup −2}, respectively. At low reverse bias voltage, quasi-continuously distributed energy levels between the minimum of the conduction bands, E{sub c} and E{sub c}-450 meV, are obtained for both doses. Conductance transients detected at low temperatures reveal that the high impurity concentration induces a band gap narrowing which leads to the formation of a barrier in the conduction band. Besides, the relationship between the activation energy and the capture cross section values of all the energy levels fits very well to the Meyer-Neldel rule. As it is known

  12. DNS BIND Server Configuration

    Directory of Open Access Journals (Sweden)

    Radu MARSANU

    2011-01-01

    Full Text Available After a brief presentation of the DNS and BIND standard for Unix platforms, the paper presents an application which has a principal objective, the configuring of the DNS BIND 9 server. The general objectives of the application are presented, follow by the description of the details of designing the program.

  13. Distributed energy storage: Time-dependent tree flow design

    Science.gov (United States)

    Bejan, A.; Ziaei, S.; Lorente, S.

    2016-05-01

    This article proposes "distributed energy storage" as a basic design problem of distributing energy storage material on an area. The energy flows by fluid flow from a concentrated source to points (users) distributed equidistantly on the area. The flow is time-dependent. Several scenarios are analyzed: sensible-heat storage, latent-heat storage, exergy storage vs energy storage, and the distribution of a finite supply of heat transfer surface between the source fluid and the distributed storage material. The chief conclusion is that the finite amount of storage material should be distributed proportionally with the distribution of the flow rate of heating agent arriving on the area. The total time needed by the source stream to "invade" the area is cumulative (the sum of the storage times required at each storage site) and depends on the energy distribution paths and the sequence in which the users are served by the source stream. Directions for future designs of distributed storage and retrieval are outlined in the concluding section.

  14. Progress and Design Concerns of Nanostructured Solar Energy Harvesting Devices.

    Science.gov (United States)

    Leung, Siu-Fung; Zhang, Qianpeng; Tavakoli, Mohammad Mahdi; He, Jin; Mo, Xiaoliang; Fan, Zhiyong

    2016-05-01

    Integrating devices with nanostructures is considered a promising strategy to improve the performance of solar energy harvesting devices such as photovoltaic (PV) devices and photo-electrochemical (PEC) solar water splitting devices. Extensive efforts have been exerted to improve the power conversion efficiencies (PCE) of such devices by utilizing novel nanostructures to revolutionize device structural designs. The thicknesses of light absorber and material consumption can be substantially reduced because of light trapping with nanostructures. Meanwhile, the utilization of nanostructures can also result in more effective carrier collection by shortening the photogenerated carrier collection path length. Nevertheless, performance optimization of nanostructured solar energy harvesting devices requires a rational design of various aspects of the nanostructures, such as their shape, aspect ratio, periodicity, etc. Without this, the utilization of nanostructures can lead to compromised device performance as the incorporation of these structures can result in defects and additional carrier recombination. The design guidelines of solar energy harvesting devices are summarized, including thin film non-uniformity on nanostructures, surface recombination, parasitic absorption, and the importance of uniform distribution of photo-generated carriers. A systematic view of the design concerns will assist better understanding of device physics and benefit the fabrication of high performance devices in the future. © 2016 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  15. Energy and environment in an architectural design application

    Energy Technology Data Exchange (ETDEWEB)

    Schiller, Silvia de; Evans, John Martin [Universidad de Buenos Aires, Facultad de Arquitectura, Diseno y Urbanismo, Buenos Aires (Argentina)

    1998-09-01

    Office buildings with important administrative functions can produce high energy demands for lighting, cooling and heating. However, appropriate architectural design can achieve significant energy savings and improve environmental conditions, without sacrificing architectural quality. Intense solar radiation and high temperature swings in dry continental climates favour deep plan offices, though natural daylight requires limited depth. This paper presents a case study of a large administrative complex project for the Justice Palace, Neuquen Province, in the cold windy sem-desert climate in the Northern Patagonia Region of Argentina, demonstrating the relevance of specialised advisory services in the architectural field. (Author)

  16. Design of advanced photocatalytic materials for energy and environmental applications

    CERN Document Server

    Coronado, Juan M; Hernández-Alonso, María D; Portela, Raquel

    2013-01-01

    Research for the development of more efficient photocatalysts has experienced an almost exponential growth since its popularization in early 1970's. Despite the advantages of the widely used TiO2, the yield of the conversion of sun power into chemical energy that can be achieved with this material is limited prompting the research and development of  a number of structural, morphological and chemical modifications of TiO2 , as well as a number of novel photocatalysts with very different composition. Design of Advanced Photocatalytic Materials for Energy and Environmental Applications provides

  17. Energy efficient engine high-pressure turbine detailed design report

    Science.gov (United States)

    Thulin, R. D.; Howe, D. C.; Singer, I. D.

    1982-01-01

    The energy efficient engine high-pressure turbine is a single stage system based on technology advancements in the areas of aerodynamics, structures and materials to achieve high performance, low operating economics and durability commensurate with commercial service requirements. Low loss performance features combined with a low through-flow velocity approach results in a predicted efficiency of 88.8 for a flight propulsion system. Turbine airfoil durability goals are achieved through the use of advanced high-strength and high-temperature capability single crystal materials and effective cooling management. Overall, this design reflects a considerable extension in turbine technology that is applicable to future, energy efficient gas-turbine engines.

  18. Materializing a responsive interior: designing minimum energy structures

    DEFF Research Database (Denmark)

    Mossé, Aurélie; Kofod, Guggi; Ramsgaard Thomsen, Mette

    2011-01-01

    This paper discusses a series of design-led experiments investigating future possibilities for architectural materialization relying on minimum energy structures as an example of adaptive structure. The structures have been made as laminates of elastic membrane under high tension with flexible......-active structures based on dielectric-elastomer, where energy-minimization and self-organization principles become central processes for the realization of shape-changing architectural surfaces. In Reef, a concept for self-actuated ceiling surface, we examine the integration of these dynamic structures...

  19. ZEUS-DO: A Design Oriented CFD-Based Unsteady Aerodynamic Capability for Flight Vehicle Multidisciplinary Configuration Shape Optimization Project

    Data.gov (United States)

    National Aeronautics and Space Administration — CFD-based design-oriented (DO) steady/unsteady aerodynamic analysis tools for Aeroelastic / Aeroservoelastic (AE/ASE) evaluation lag significantly behind other...

  20. Designing Energy Conversion Systems for the Next Decade

    Directory of Open Access Journals (Sweden)

    Slobodan N. Vukosavić

    2012-12-01

    Full Text Available Sustainable growth in energy consumption requires transition to clean and green energy sources and energy systems. Environment friendly and renewable energy systems deal with electrical energy and rely on efficient electrical power converters. High power electronics is the key technology to deal with the next generation of electrical energy systems. The door to future breakthroughs in high power electronics is opened by major improvement in semiconductor power devices and their packaging technologies. New materials allow for much higher junction temperatures and higher operating voltages. Most importantly, advanced power semiconductor devices and novel converter topology open the possibility to increase the energy efficiency of power conversion and reduce the amount of heat. Although the waste heat created by high power converters can be put to use by adding on to heating systems, this option is not always available and the conversion losses are mostly wasted. At the same time, wasted heat is a form of pollution that threatens the environment. Another task for high power converters is efficient harvesting of renewable energy sources, such as the wind energy and the sun. Intermittent in nature, they pose a difficult task to power converter topology and controls. Eventually, high power converters are entering power distribution and transmission networks. With their quick reaction, with fast communication between the grid nodes and with advanced controllability of high power converters, a number of innovations can be introduced, facilitating the power system control and allowing for optimizations and loss reduction. Coined smart grid, this solution comprises two key elements, and these are intelligent controls and large static power converters. At virtually no cost, smart grids allow for a better utilization of available resources and it enlarges the stable operating range of the transmission systems. Therefore, it is of interest to review the

  1. Simultaneous analysis of matter radii, transition probabilities, and excitation energies of Mg isotopes by angular-momentum-projected configuration-mixing calculations

    CERN Document Server

    Shimada, Mitsuhiro; Tagami, Shingo; Matsumoto, Takuma; Shimizu, Yoshifumi R; Yahiro, Masanobu

    2016-01-01

    We perform simultaneous analysis of (1) matter radii, (2) $B(E2; 0^+ \\rightarrow 2^+ )$ transition probabilities, and (3) excitation energies, $E(2^+)$ and $E(4^+)$, for $^{24-40}$Mg by using the beyond mean-field (BMF) framework with angular-momentum-projected configuration mixing with respect to the axially symmetric $\\beta_2$ deformation with infinitesimal cranking. The BMF calculations successfully reproduce all of the data for $r_{\\rm m}$, $B(E2)$, and $E(2^+)$ and $E(4^+)$, indicating that it is quite useful for data analysis, particularly for low-lying states. We also discuss the absolute value of the deformation parameter $\\beta_2$ deduced from measured values of $B(E2)$ and $r_{\\rm m}$. This framework makes it possible to investigate the effects of $\\beta_2$ deformation, the change in $\\beta_2$ due to restoration of rotational symmetry, $\\beta_2$ configuration mixing, and the inclusion of time-odd components by infinitesimal cranking. Under the assumption of axial deformation and parity conservation,...

  2. Simultaneous analysis of matter radii, transition probabilities, and excitation energies of Mg isotopes by angular-momentum-projected configuration-mixing calculations

    Science.gov (United States)

    Shimada, Mitsuhiro; Watanabe, Shin; Tagami, Shingo; Matsumoto, Takuma; Shimizu, Yoshifumi R.; Yahiro, Masanobu

    2016-06-01

    We perform simultaneous analysis of (1) matter radii, (2) B (E 2 ;0+→2+) transition probabilities, and (3) excitation energies, E (2+) and E (4+) , for Mg-4024 by using the beyond-mean-field (BMF) framework with angular-momentum-projected configuration mixing with respect to the axially symmetric β2 deformation with infinitesimal cranking. The BMF calculations successfully reproduce all of the data for rm,B (E 2 ) , and E (2+) and E (4+) , indicating that it is quite useful for data analysis; particularly for low-lying states. We also discuss the absolute value of the deformation parameter β2 deduced from measured values of B (E 2 ) and rm. This framework makes it possible to investigate the effects of β2 deformation, the change in β2 due to restoration of rotational symmetry, β2 configuration mixing, and the inclusion of time-odd components by infinitesimal cranking. Under the assumption of axial deformation and parity conservation, we clarify which effect is important for each of the three measurements and propose the kinds of BMF calculations that are practical for each of the three kinds of observables.

  3. Design of HART Configuration Software Based on Windows%基于Windows的HART组态软件设计

    Institute of Scientific and Technical Information of China (English)

    张夏; 魏文雄; 余淼; 郭江伟

    2012-01-01

    针对PC在Windows操作系统下实时性差和状态机功能不易实现的问题,根据PC自带的性能计数器,构造一个高精度、低开销的定时器,其计数精度可以达到毫秒级以下.采用AES算法对HART控制命令进行加密保护,实验结果证明,HART组态软件具有较好的实时性和安全性,适用于工业控制的现场数据通信.%Under the circumstances of the Windows operating system of personal computer, the function of state machine is not easy to realize. Based on PC's own performance counters, this paper presents a method to make a high-precision and low-overhead timer, which satisfies the strict demands for real time of HART control software. Meanwhile, AES algorithm is applied to protect the HART control commands. Experimental result shows that the HART configuration software has a high degree of real-time and safety, which provides a solution to the data communication in industrial control field.

  4. Ocean Thermal Energy Conversion power system development. Phase I: preliminary design. Final report

    Energy Technology Data Exchange (ETDEWEB)

    1978-12-04

    Westinghouse has completed the Preliminary Design Phase for the Power System Development of the Ocean Thermal Energy Conversion (OTEC) Demonstration Plant project. This study included the development of a preliminary design for a Modular Application scaled power system (10MWe) and Heat Exchanger Test Articles, both based on the concept developed in the Conceptual Design Phase. The results of this study were used to improve the baseline design of the 50MWe module for the Commercial Size Power System, which was recommended for the demonstration plant by the conceptual design study. The 50MWe module was selected since it has the lowest cost, and since its size convincingly demonstrates that future economically viable commercial plants, having reliable operation with credible anticipated costs, are possible. Additional optimization studies on the size of the power system plus hull continue to identify 50MWe as the preferred minimum cost configuration. This study was limited to a closed cycle ammonia power system module, using a seawater temperature difference of 40/sup 0/F, and a surface platform/ship reference hull. This volume describes system operation, a complete test program to verify mechanical reliability and thermal performance, fabrication and installation operations, and a cost analysis. (WHK)

  5. Method for Predicting the Energy Characteristics of Li-Ion Cells Designed for High Specific Energy

    Science.gov (United States)

    Bennett, William, R.

    2012-01-01

    Novel electrode materials with increased specific capacity and voltage performance are critical to the NASA goals for developing Li-ion batteries with increased specific energy and energy density. Although performance metrics of the individual electrodes are critically important, a fundamental understanding of the interactions of electrodes in a full cell is essential to achieving the desired performance, and for establishing meaningful goals for electrode performance in the first place. This paper presents design considerations for matching positive and negative electrodes in a viable design. Methods for predicting cell-level performance, based on laboratory data for individual electrodes, are presented and discussed.

  6. Residential buildings: Energy conservation (energy savings design code). Il Patrimonio residenziale pubblico

    Energy Technology Data Exchange (ETDEWEB)

    Los, S.; Pulizer, N.; Agnoletto, L.; Buggin, A.

    1991-01-01

    The energy savings design code presented in this paper was based on the energy performance of the basic types of residential buildings commonly found in Italy and the numerous combinations of energy savings measures which were hypothesized for them. The calculation algorithm carries out two distinct operations: the quantification of seasonal fuel consumption and the cost of proposed interventions. The code takes into account parameters defining: climatic data; building geometry, surface area, orientation (insolation, etc.); thermal insulation, including the thermal/physical material properties of the other construction materials; thermal comfort conditions; and the type and performance of conventional heating equipment components, including active and passive architectural systems and their relative control systems.

  7. Chamber Design for the Laser Inertial Fusion Energy (LIFE) Engine

    Energy Technology Data Exchange (ETDEWEB)

    Latkowski, J F; Abbott, R P; Aceves, S; Anklam, T; Badders, D; Cook, A W; DeMuth, J; Divol, L; El-Dasher, B; Farmer, J C; Flowers, D; Fratoni, M; ONeil, R G; Heltemes, T; Kane, J; Kramer, K J; Kramer, R; Lafuente, A; Loosmore, G A; Morris, K R; Moses, G A; Olson, B; Pantano, C; Reyes, S; Rhodes, M; Roe, K; Sawicki, R; Scott, H; Spaeth, M; Tabak, M; Wilks, S

    2010-11-30

    The Laser Inertial Fusion Energy (LIFE) concept is being designed to operate as either a pure fusion or hybrid fusion-fission system. The present work focuses on the pure fusion option. A key component of a LIFE engine is the fusion chamber subsystem. It must absorb the fusion energy, produce fusion fuel to replace that burned in previous targets, and enable both target and laser beam transport to the ignition point. The chamber system also must mitigate target emissions, including ions, x-rays and neutrons and reset itself to enable operation at 10-15 Hz. Finally, the chamber must offer a high level of availability, which implies both a reasonable lifetime and the ability to rapidly replace damaged components. An integrated design that meets all of these requirements is described herein.

  8. Mathematical programming models for the economic design and assessment of wind energy conversion systems

    Science.gov (United States)

    Reinert, K. A.

    The use of linear decision rules (LDR) and chance constrained programming (CCP) to optimize the performance of wind energy conversion clusters coupled to storage systems is described. Storage is modelled by LDR and output by CCP. The linear allocation rule and linear release rule prescribe the size and optimize a storage facility with a bypass. Chance constraints are introduced to explicitly treat reliability in terms of an appropriate value from an inverse cumulative distribution function. Details of deterministic programming structure and a sample problem involving a 500 kW and a 1.5 MW WECS are provided, considering an installed cost of $1/kW. Four demand patterns and three levels of reliability are analyzed for optimizing the generator choice and the storage configuration for base load and peak operating conditions. Deficiencies in ability to predict reliability and to account for serial correlations are noted in the model, which is concluded useful for narrowing WECS design options.

  9. A Curtain Design on Optimizing Configuration of Savonius Rotor%阻力型垂直轴风力机导风帘的优化设计

    Institute of Scientific and Technical Information of China (English)

    谢晶; 王亚军; 罗秉东; 宋宁亮

    2012-01-01

    以输出功率100W的阻力型垂直轴型风力机为例,通过优化设计找寻最佳的叶片数目、高径比和折叠率等几何参量,然后加入导风帘装置,给出一个最佳结构方案。运用Fluent求解器中的有限体积法对无导风帘和三种不同长度导风帘设计的叶片周围的流场进行模拟。模拟与最佳优化方式的性能参数的计算结果表明,采用长导风帘设计的阻力型垂直轴风力机具有最好的动力学性能,可以提高运行效率。%This paper mainly studies the configuration of Savonius rotor on the basis of the output power P= 100 W, and the best parameters of the number of blade.aspect ratio and overlap ratio have been found. On this basis, a curtain arrangement has been designed, and the optimum configuration of Savonius rotor has been put forward in this study. Then, the multifarious blades of Savonius wind rotor without or with curtain have been placed in the wind tunnel and simulated by the fluid engineer simulation software Fluent with the finite volume method. And these conclusion combined with the calculation of the aerodynamic performance parameters of the optimum configuration of Savonius rotor verify the design on Savonius rotor with long curtain in the possession of the best dynamic performance. This optimum Savonius rotor in the present study has achieved the improve- ment of the operating efficiency.

  10. Cross Section Measurement of ^2H(n,np)n at 16 MeV in Symmetric Constant Relative Energy Configurations

    Science.gov (United States)

    Couture, A.; Clegg, T. B.; Howell, C. R.; Tajima, S.; Crowell, A.; Esterline, J.; Fallin, B.; Cumberbatch, L.; Crowe, B.; Markoff, D.; Pedroni, R.

    2010-11-01

    We have made cross-section measurements of neutron-deuteron breakup at an incident neutron energy of 16 MeV. The scattered proton was detected in coincidence with one of the neutrons and their energies were determined via time-of-flight techniques. Target-beam luminosity is obtained from n-d elastic scattering performed concurrently with the main experiment by detecting the scattered deuteron. Our current measurements are of two special cases of the Symmetric Constant Relative Energy Configuration: the space-star and the coplanar star. Data are compared with theoretical predictions [1] through Monte Carlo calculations which smear point geometry predictions over the finite beam, target, and detectors. Preliminary results for the space star are in agreement with previous experimental measurements [2] and are at least 20% larger than theoretical predictions. [4pt] [1] H Witala and W Glóckle. J. Phys. G: Nucl. Part. Phys. 37 064003 (2010). [0pt] [2] C.R. Howell, Nucl. Phys. A 689, 298c (2001).

  11. Multireference configuration interaction potential curve and analytical potential energy function of the ground and low-lying excited states of CdSe

    Institute of Scientific and Technical Information of China (English)

    Gao Feng; Yang Chuan-Lu; Hu Zhen-Yan; Wang Mei-Shan

    2007-01-01

    The potential energy curves (PECs) of the ground state (3Π) and three low-lying excited states (1∑, 3∑,1Π) of CdSe dimer have been studied by emploging quasirelativistic effective core potentials on the basis of the complete active space self-consistent field method followed by multireference configuration interaction calculation. The four PECs are fitted to analytical potential energy functions using the Murrel-Sorbie potential function. Based on the PECs,the vibrational levels of the four states are determined by solving the Schr(o)dinger equation of nuclear motion, and corresponding spectroscopic contants are accurately calculated. The equilibrium positions as well as the spectroscopic constants and the vibrational levels are reported. By our analysis, the 3Π state, of which the dissociation asymptote is Cd(1S) + Se(3p), is identified as a ground state of CdSe dimer, and the corresponding dissociation energy is estimated to be 0.39eV. However, the first excited state is only 1132.49cm-1 above the ground state and the 3∑ state is the highest in the four calculated states.

  12. Optimization of design parameters of low-energy buildings

    Science.gov (United States)

    Vala, Jiří; Jarošová, Petra

    2017-07-01

    Evaluation of temperature development and related consumption of energy required for heating, air-conditioning, etc. in low-energy buildings requires the proper physical analysis, covering heat conduction, convection and radiation, including beam and diffusive components of solar radiation, on all building parts and interfaces. The system approach and the Fourier multiplicative decomposition together with the finite element technique offers the possibility of inexpensive and robust numerical and computational analysis of corresponding direct problems, as well as of the optimization ones with several design variables, using the Nelder-Mead simplex method. The practical example demonstrates the correlation between such numerical simulations and the time series of measurements of energy consumption on a small family house in Ostrov u Macochy (35 km northern from Brno).

  13. Energy efficient cross layer design for spectrum sharing systems

    KAUST Repository

    Alabbasi, Abdulrahman

    2016-10-06

    We propose a cross layer design that optimizes the energy efficiency of spectrum sharing systems. The energy per good bit (EPG) is considered as an energy efficiency metric. We optimize the secondary user\\'s transmission power and media access frame length to minimize the EPG metric. We protect the primary user transmission via an outage probability constraint. The non-convex targeted problem is optimized by utilizing the generalized convexity theory and verifying the strictly pseudo-convex structure of the problem. Analytical results of the optimal power and frame length are derived. We also used these results in proposing an algorithm, which guarantees the existence of a global optimal solution. Selected numerical results show the improvement of the proposed system compared to other systems. © 2016 IEEE.

  14. Changing energy efficient houses into net zero energy houses : guidelines for a design exercise

    Energy Technology Data Exchange (ETDEWEB)

    Proskiw, G. [Proskiw Engineering Ltd., Winnipeg, MB (Canada); Hockman, J. [J.L. Hockman Consulting Inc., Winnipeg, MB (Canada)

    2006-03-31

    A net zero energy house (NZEH) generates surplus energy during certain portions of the year which can then be sold back to a utility through the existing power grid or pipeline. The surplus equals or exceeds the power which has to be purchased from the utility during the remaining parts of the year, which means that the house uses the power grid as a permanently connected energy storage system. This paper provided details of a conceptual design exercise to upgrade the design of an existing energy efficient Canadian house from its current performance level to that of a NZEH. The design objectives included the caveat that the occupants should maintain the standard of living enjoyed in the house before NZEH modifications. The simulation program HOT2000 was used to predict the energy performance of the house. Default values were selected for thermostat settings; appliance energy usage, domestic hot water (DHW) consumption; and metabolic gains. Both wood heating and on-site hydro generation were excluded from the design exercise because neither were judged as realistic options for the vast majority of Canadians. An assumption of no external shading from adjacent structures was selected to produce optimum solar advantage. It was decided that photovoltaics (PV) would provide the major source of on-site power generation despite their high initial cost. The monitoring and energy analysis program indicated that the house would exceed its energy target by 53 per cent. However, 78 per cent of the over-consumption was due to limitations of the computer software initially used to design the house in 1992. Mechanical systems were judged as too complex, too expensive and too unreliable. The mechanical ventilation system maintained good air quality, but was overly-complex. Overheating was a problem despite the use of exterior solar shade screens. Better design tools were needed to assess the probability of overheating. No major problems were encountered with the building envelope

  15. State Energy Efficiency Resource Standards: Design, Status, and Impacts

    Energy Technology Data Exchange (ETDEWEB)

    Steinberg, D.; Zinaman, O.

    2014-05-01

    An energy efficiency resource standard (EERS) is a policy that requires utilities or other entities to achieve a specified amount of energy savings through customer energy efficiency programs within a specified timeframe. EERSs may apply to electricity usage, natural gas usage, or both. This paper provides an overview of the key design features of EERSs for electricity, reviews the variation in design of EERSs across states, and provides an estimate of the amount of savings required by currently specified EERSs in each state. As of December, 2013, 23 states have active and binding EERSs for electricity. We estimate that state EERSs will require annual electricity savings of approximately 8-11% of total projected demand by 2020 in states with EERSs, however the level of savings targeted by the policies varies significantly across states. In addition to the variation in targeted savings, the design of EERSs varies significantly across states leading to differences in the suite of incentives created by the policy, the flexibility of compliance with the policy, the balance of benefits and costs of the policy between producers and consumers, and the certainty with which the policy will drive long-term savings.

  16. Energy and time determine scaling in biological and computer designs.

    Science.gov (United States)

    Moses, Melanie; Bezerra, George; Edwards, Benjamin; Brown, James; Forrest, Stephanie

    2016-08-19

    Metabolic rate in animals and power consumption in computers are analogous quantities that scale similarly with size. We analyse vascular systems of mammals and on-chip networks of microprocessors, where natural selection and human engineering, respectively, have produced systems that minimize both energy dissipation and delivery times. Using a simple network model that simultaneously minimizes energy and time, our analysis explains empirically observed trends in the scaling of metabolic rate in mammals and power consumption and performance in microprocessors across several orders of magnitude in size. Just as the evolutionary transitions from unicellular to multicellular animals in biology are associated with shifts in metabolic scaling, our model suggests that the scaling of power and performance will change as computer designs transition to decentralized multi-core and distributed cyber-physical systems. More generally, a single energy-time minimization principle may govern the design of many complex systems that process energy, materials and information.This article is part of the themed issue 'The major synthetic evolutionary transitions'.

  17. Euler Technology Assessment for Preliminary Aircraft Design-Unstructured/Structured Grid NASTD Application for Aerodynamic Analysis of an Advanced Fighter/Tailless Configuration

    Science.gov (United States)

    Michal, Todd R.

    1998-01-01

    This study supports the NASA Langley sponsored project aimed at determining the viability of using Euler technology for preliminary design use. The primary objective of this study was to assess the accuracy and efficiency of the Boeing, St. Louis unstructured grid flow field analysis system, consisting of the MACGS grid generation and NASTD flow solver codes. Euler solutions about the Aero Configuration/Weapons Fighter Technology (ACWFT) 1204 aircraft configuration were generated. Several variations of the geometry were investigated including a standard wing, cambered wing, deflected elevon, and deflected body flap. A wide range of flow conditions, most of which were in the non-linear regimes of the flight envelope, including variations in speed (subsonic, transonic, supersonic), angles of attack, and sideslip were investigated. Several flowfield non-linearities were present in these solutions including shock waves, vortical flows and the resulting interactions. The accuracy of this method was evaluated by comparing solutions with test data and Navier-Stokes solutions. The ability to accurately predict lateral-directional characteristics and control effectiveness was investigated by computing solutions with sideslip, and with deflected control surfaces. Problem set up times and computational resource requirements were documented and used to evaluate the efficiency of this approach for use in the fast paced preliminary design environment.

  18. Potential of shading devices and glazing configurations on cooling energy savings for high-rise office buildings in hot-humid climates: The case of Malaysia

    Directory of Open Access Journals (Sweden)

    Allen Khin Kiet Lau

    2016-12-01

    Full Text Available Rapid growing of energy use has raised critical concerns over energy supply difficulties and negative environmental impacts globally and among ASEAN countries. Malaysia is experiencing a high average annual energy demand growth rate of approximately 2.3% which large portion of that energy is used by office buildings. Under the hot-humid climatic conditions in Malaysia, high-rise office buildings with large or fully glazed façades are facing a major problem of overheating due to high solar radiation through the glazed façades. This has caused high cooling energy requirements. The aim of this study is to investigate the potential of three types of shading devices on cooling energy savings when applied at different façade orientations. The aim also extends to investigations on different cooling energy savings when shading devices are applied on façade glazing with different configurations and thermal performances. This was done through a case study of a high-rise office building in Kuala Lumpur, Malaysia using IES (VE building thermal simulation software. Twenty simulation building models were applied with different shading devices at different façade orientations and with high and low performance façade glazing. The simulation results indicate that high-rise office buildings in Malaysia use approximately 45.9% of total building energy for cooling purposes. The results also suggest that use of various shading devices on low-e double glazed façades will result between 1.0% and 3.4% annual cooling energy savings, depending on the types of shading devices and façade orientations. The estimated annual cooling energy savings increase to between 5.0% and 9.9% when the shading devices are applied to all orientations of low-e double glazed façades. The estimated annual cooling energy savings further increase to between 5.6% and 10.4% when the façade glazing is replaced by single clear glazing. This study recommends prioritizing shading devices on

  19. Compressed-air energy storage preliminary design and site development program in an aquifer. Volume 5, Part 1: Turbomachinery design

    Science.gov (United States)

    Berman, P. A.; Bonk, J. S.; Kobett, W. F.; Kosanovich, N. S.; Long, L. J.; Marinacci, D. J.

    1982-11-01

    The development of the design approach for a combustion turbine heat cycle and the major mechanical equipment for use by an electric utility at a selected aquifer air storage site is documented. A compressed air energy storage (CAES) system utilizes off peak electric power, available from base load power plants, to store compressed air underground in an aquifer. During subsequent periods, the stored air is extracted from the aquifer and used as an air supply for a generating combustion turbine expander. The aquifer has an initial discovery pressure of 840 psia. An initial air injection temperature of 1500 F was selected. The major mechanical equipment considered includes: the turbine motor/generator compressor train, intercooler and aftercooler system, and the exhaust gas regenerator. The cycle and machinery configuration and the specific mechanical equipment were selected for their Media site characteristics. These characteristics and the effect of component interdependency are considered when a conservative component design approach is established which satisfies the Media site CAES system requirements.

  20. Mechanical Design of a High Energy Beam Absorber for the Advanced Superconducting Test Accelerator (ASTA) at Fermilab

    Energy Technology Data Exchange (ETDEWEB)

    Baffes, C.; Church, M.; Leibfritz, J.; Oplt, S.; Rakhno, I.; /Fermilab

    2012-05-10

    A high energy beam absorber has been built for the Advanced Superconducting Test Accelerator (ASTA) at Fermilab. In the facility's initial configuration, an electron beam will be accelerated through 3 TTF-type or ILC-type SRF cryomodules to an energy of 750MeV. The electron beam will be directed to one of multiple downstream experimental and diagnostic beam lines and then deposited in one of two beam absorbers. The facility is designed to accommodate up to 6 cryomodules, which would produce a 75kW beam at 1.5GeV; this is the driving design condition for the beam absorbers. The beam absorbers consist of water-cooled graphite, aluminum and copper layers contained in a helium-filled enclosure. This paper describes the mechanical implementation of the beam absorbers, with a focus on thermal design and analysis. The potential for radiation-induced degradation of the graphite is discussed.