78 FR 70211 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2013-11-25

... Replacement figures of Boeing Special Attention Service Bulletin 757- 57-0071, dated September 12, 2012. The... information identified in this AD, contact Boeing Commercial Airplanes, Attention: Data & Services Management... Operations, M-30, West Building [[Page 70212

77 FR 61548 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2012-10-10

...-indicating and crew-alerting system (EICAS) messages ALT DISAGREE and IAS DISAGREE displayed. The flightcrew... Special Attention Service Bulletin 727-34-0245, dated June 4, 2008 (for Model airplanes); [[Page 61549... -200C series airplanes); and Boeing Special Attention Service Bulletin 747-34-2925, dated June 4, 2008...

78 FR 49978 - Airworthiness Directives; the Boeing Company Airplanes

Science.gov (United States)

2013-08-16

... Pohl, Aerospace Engineer, Airframe Branch, ANM-120S, FAA, Seattle Aircraft Certification Office, 1601... Engineering Representative. Differences Between the Proposed AD and the Service Information Boeing Alert... structure not covered by the repair instructions in Boeing Alert Service Bulletin 737-53A1075, Revision 3...

78 FR 11972 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2013-02-21

... corresponding figures of Boeing Special Attention Service Bulletin 737-53-1287, Revision 1, dated November 15... service information identified in this AD, contact Boeing Commercial Airplanes, Attention: Data & Services... Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE...

77 FR 54798 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2012-09-06

... that Figures 18 and 23 of Boeing Special Attention Service Bulletin 747-25-3586, dated November 12.... ADDRESSES: For service information identified in this AD, contact Boeing Commercial Airplanes, Attention.... Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New...

78 FR 9 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2013-01-02

..., Revision 1, dated March 31, 2005. (ii) At the times specified in Figure 8 of Boeing Special Attention... information identified in this AD, contact Boeing Commercial Airplanes, Attention: Data & Services Management... Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE...

78 FR 79289 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2013-12-30

... service information identified in this AD, contact Boeing Commercial Airplanes, Attention: Data & Services... Management Facility, U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor... that Figure 4, Sheets 2 and 3 of Boeing Alert Service Bulletin 747-25A3613, dated June 22, 2012, show...

78 FR 25372 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2013-05-01

... this AD, contact Boeing Commercial Airplanes, Attention: Data & Services Management, P. O. Box 3707, MC... Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE., Washington, DC 20590... Part 5 of the Accomplishment Instructions and corresponding figures of Boeing Service Bulletin 737-53...

78 FR 25369 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2013-05-01

..., contact Boeing Commercial Airplanes, Attention: Data & Services Management, P.O. Box 3707, MC 2H-65... Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE., Washington, DC 20590... and corresponding figures of Boeing Service Bulletin 737-53-1310, dated October 20, 2011, are not...

77 FR 16147 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2012-03-20

... identified in this AD, contact Boeing Commercial Airplanes, Attention: Data & Services Management, P.O. Box... Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE... that note (f) of Figures 10 and 24 of Boeing Alert Service Bulletin 767-56A0010, Revision 1, dated...

77 FR 41041 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2012-07-12

... Clarify Note (d) of Figures 1 and 2 UAL noted that STEP 2, Note (d), of Boeing Special Attention Service... in this AD, contact Boeing Commercial Airplanes, Attention: Data & Services Management, P.O. Box 3707... Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE...

78 FR 65166 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2013-10-31

..., contact Boeing Commercial Airplanes, Attention: Data & Services Management, P.O. Box 3707, MC 2H-65... Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE., Washington, DC 20590. FOR FURTHER...'' inspections, done in accordance with Part 4 and Figure 8 of Boeing Alert Service Bulletin 747-53A2371...

77 FR 41931 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2012-07-17

... changes shown in Figures 2 and 7 of Boeing Special Attention Service Bulletin 737-30- 1058, Revision 3... Information Reference American stated that, in Figures 4 and 9 of Boeing Special Attention Service Bulletin... Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE...

78 FR 17285 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2013-03-21

..., contact Boeing Commercial Airplanes, Attention: Data & Services Management, P.O. Box 3707, MC 2H-65... Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE., Washington, DC 20590... performing Figures 7 through 10 of Boeing Service Bulletin 767-27A0224, Revision 1, dated December 16, 2011...

77 FR 2669 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2012-01-19

...'' column of Table 1 of Figure 1 of Boeing Special Attention Service Bulletin 737-53-1234, Revision 1, dated... times specified in Figure 8 of Boeing Special Attention Service Bulletin 737-53-1234, Revision 1, dated... Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE...

76 FR 22828 - Airworthiness Directives; The Boeing Company Model 737-700 Series Airplanes

Science.gov (United States)

2011-04-25

... January 20, 2010. Those special attention service bulletins describe procedures for doing a general visual... General Visual Inspection of Seat Tracks (i) For airplanes identified in Boeing Special Attention Service... results from reports that the aft seat leg fittings span the station (STA) 521.45 stay-out zone. We are...

75 FR 9760 - Airworthiness Directives; The Boeing Company Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747...

Science.gov (United States)

2010-03-04

.... ADDRESSES: For service information identified in this AD, contact Boeing Commercial Airplanes, Attention... Management Facility, U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor.... Figure 31, Sheet 7, of the Accomplishment Instructions of Boeing Alert Service Bulletin 747- 51A2060...

75 FR 22514 - Airworthiness Directives; The Boeing Company Model 747-200B Series Airplanes

Science.gov (United States)

2010-04-29

... Administration (FAA), DOT. ACTION: Final rule; request for comments. SUMMARY: We are adopting a new airworthiness... cracking of the fuselage skin lap joints at stringer 6 on the left and right sides from station (STA) 340... repetitive inspections for the modified area. This AD results from reviews done by Boeing, which show that...

Final Technical Report. Project Boeing SGS

Energy Technology Data Exchange (ETDEWEB)

Bell, Thomas E. [The Boeing Company, Seattle, WA (United States)

2014-12-31

Boeing and its partner, PJM Interconnection, teamed to bring advanced “defense-grade” technologies for cyber security to the US regional power grid through demonstration in PJM’s energy management environment. Under this cooperative project with the Department of Energy, Boeing and PJM have developed and demonstrated a host of technologies specifically tailored to the needs of PJM and the electric sector as a whole. The team has demonstrated to the energy industry a combination of processes, techniques and technologies that have been successfully implemented in the commercial, defense, and intelligence communities to identify, mitigate and continuously monitor the cyber security of critical systems. Guided by the results of a Cyber Security Risk-Based Assessment completed in Phase I, the Boeing-PJM team has completed multiple iterations through the Phase II Development and Phase III Deployment phases. Multiple cyber security solutions have been completed across a variety of controls including: Application Security, Enhanced Malware Detection, Security Incident and Event Management (SIEM) Optimization, Continuous Vulnerability Monitoring, SCADA Monitoring/Intrusion Detection, Operational Resiliency, Cyber Range simulations and hands on cyber security personnel training. All of the developed and demonstrated solutions are suitable for replication across the electric sector and/or the energy sector as a whole. Benefits identified include; Improved malware and intrusion detection capability on critical SCADA networks including behavioral-based alerts resulting in improved zero-day threat protection; Improved Security Incident and Event Management system resulting in better threat visibility, thus increasing the likelihood of detecting a serious event; Improved malware detection and zero-day threat response capability; Improved ability to systematically evaluate and secure in house and vendor sourced software applications; Improved ability to continuously monitor

Data Mining of NASA Boeing 737 Flight Data: Frequency Analysis of In-Flight Recorded Data

Science.gov (United States)

Butterfield, Ansel J.

2001-01-01

Data recorded during flights of the NASA Trailblazer Boeing 737 have been analyzed to ascertain the presence of aircraft structural responses from various excitations such as the engine, aerodynamic effects, wind gusts, and control system operations. The NASA Trailblazer Boeing 737 was chosen as a focus of the study because of a large quantity of its flight data records. The goal of this study was to determine if any aircraft structural characteristics could be identified from flight data collected for measuring non-structural phenomena. A number of such data were examined for spatial and frequency correlation as a means of discovering hidden knowledge of the dynamic behavior of the aircraft. Data recorded from on-board dynamic sensors over a range of flight conditions showed consistently appearing frequencies. Those frequencies were attributed to aircraft structural vibrations.

ATM Technology Demonstration-1 Phase II Boeing Configurable Graphical Display (CGD) Software Design Description

Science.gov (United States)

Wilber, George F.

2017-01-01

This Software Description Document (SDD) captures the design for developing the Flight Interval Management (FIM) system Configurable Graphics Display (CGD) software. Specifically this SDD describes aspects of the Boeing CGD software and the surrounding context and interfaces. It does not describe the Honeywell components of the CGD system. The SDD provides the system overview, architectural design, and detailed design with all the necessary information to implement the Boeing components of the CGD software and integrate them into the CGD subsystem within the larger FIM system. Overall system and CGD system-level requirements are derived from the CGD SRS (in turn derived from the Boeing System Requirements Design Document (SRDD)). Display and look-and-feel requirements are derived from Human Machine Interface (HMI) design documents and working group recommendations. This Boeing CGD SDD is required to support the upcoming Critical Design Review (CDR).

76 FR 24354 - Airworthiness Directives; The Boeing Company Model 777-200 and -300 Series Airplanes Equipped...

Science.gov (United States)

2011-05-02

... this AD, contact Boeing Commercial Airplanes, Attention: Data & Services Management, P.O. Box 3707, MC.... Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New.... Required parts cost about $122,617 per product. Based on these figures, we estimate the cost of this AD to...

76 FR 42607 - Airworthiness Directives; The Boeing Company Model 767-200, -300, and -400ER Series Airplanes

Science.gov (United States)

2011-07-19

... CONTACT: Stephen Styskal, Aerospace Engineer, Cabin Safety and Environmental Systems Branch, ANM-150S, FAA...) 917-6439; fax: (425) 917-6590; e- mail: stephen[email protected] . SUPPLEMENTARY INFORMATION: Comments... Information (h) Actions done before the effective date of this AD in accordance with Boeing Special Attention...

75 FR 9137 - Airworthiness Directives; The Boeing Company Model 737-100, -200, -200C, -300, -400, and -500...

Science.gov (United States)

2010-03-01

... AD, contact Boeing Commercial Airplanes, P.O. Box 3707, Seattle, Washington 98124-2207. Examining the... repetitive detailed and magnetic particle inspections to detect discrepancies (including corrosion, pitting... detailed inspection for corrosion, pitting, and cracking of the carriage spindle, the magnetic particle...

75 FR 5677 - Airworthiness Directives; The Boeing Company Model 767-200, -300, and -300F Series Airplanes

Science.gov (United States)

2010-02-04

... AD, contact Boeing Commercial Airplanes, Attention: Data & Services Management, P.O. Box 3707, MC 2H... a magnetic particle inspection (MPI) in accordance with Part 4, ``Magnetic Particle Inspection of... November 5, 2009, or MPI in accordance with Part 4, ``Magnetic Particle Inspection of the Midspar Fuse Pin...

ANALYSIS FOR AERODYNAMICS OF THE SIMPLIFIED MODEL OF A COMMERCIAL AIRPLANE CRUISING AT TRANSONIC SPEED

OpenAIRE

KIM YANGKYUN; KIM SUNGCHO

2010-01-01

This paper describes the computational analysis and visualization of flow around the model of a commercial airplane, Boeing 747-400. The geometry was realized through reverse engineering technique based on the photo scanning measurement. The steady three-dimensional viscous compressible governing equations were solved in the unstructured grid system. The basic conditions for computation were chosen as the same to those of Boeing 747-400’s cruising state. The high Reynolds turbulence models ar...

76 FR 60710 - Airworthiness Directives; The Boeing Company Model 737-600, -700, -700C, -800, and -900 Series...

Science.gov (United States)

2011-09-30

... universal fault interrupters (UFIs) using a certain supplemental type certificate. This new AD continues to... interrupter (GFI) feature, or installation and maintenance of universal fault interrupters (UFIs) using a... section of this AD to include this contact information. Request To Revise a Word Boeing requested a change...

78 FR 52107 - Special Conditions: Boeing Model 777-200, -300, and -300ER Series Airplanes; Rechargeable Lithium...

Science.gov (United States)

2013-08-22

... passengers. The Model 777-200, -300, and -300ER series airplanes have fly-by-wire controls, fully software... lead acid batteries and nickel cadmium batteries. These special conditions provide an equivalent level... characteristics that differ significantly from those of the nickel cadmium and lead acid rechargeable batteries...

75 FR 81508 - Airworthiness Directives; The Boeing Company Model 777-200, -200LR, -300, and -300ER Series...

Science.gov (United States)

2010-12-28

... require installing new panels in the main equipment center, making certain wiring changes, installing new..., Boeing found indications of wiring deterioration that could cause electrical faults in the main tank... center; making certain wiring changes; installing new GFI relays in the P301 and P302 panels; and...

BOES: Building Occupancy Estimation System using sparse ambient vibration monitoring

Science.gov (United States)

Pan, Shijia; Bonde, Amelie; Jing, Jie; Zhang, Lin; Zhang, Pei; Noh, Hae Young

2014-04-01

In this paper, we present a room-level building occupancy estimation system (BOES) utilizing low-resolution vibration sensors that are sparsely distributed. Many ubiquitous computing and building maintenance systems require fine-grained occupancy knowledge to enable occupant centric services and optimize space and energy utilization. The sensing infrastructure support for current occupancy estimation systems often requires multiple intrusive sensors per room, resulting in systems that are both costly to deploy and difficult to maintain. To address these shortcomings, we developed BOES. BOES utilizes sparse vibration sensors to track occupancy levels and activities. Our system has three major components. 1) It extracts features that distinguish occupant activities from noise prone ambient vibrations and detects human footsteps. 2) Using a sequence of footsteps, the system localizes and tracks individuals by observing changes in the sequences. It uses this tracking information to identify when an occupant leaves or enters a room. 3) The entering and leaving room information are combined with detected individual location information to update the room-level occupancy state of the building. Through validation experiments in two different buildings, our system was able to achieve 99.55% accuracy for event detection, less than three feet average error for localization, and 85% accuracy in occupancy counting.

75 FR 8554 - Airworthiness Directives; The Boeing Company Model 747-100, -200B, and -200F Series Airplanes

Science.gov (United States)

2010-02-25

...-0132; Directorate Identifier 2009-NM-096-AD] RIN 2120-AA64 Airworthiness Directives; The Boeing Company... approaching or have exceeded their design life goal. We issued that AD to prevent separation of fuselage skin...,000 flight cycles to 1,000 flight cycles. Differences Between the Proposed AD and Service Bulletin...

ANALYSIS FOR AERODYNAMICS OF THE SIMPLIFIED MODEL OF A COMMERCIAL AIRPLANE CRUISING AT TRANSONIC SPEED

Directory of Open Access Journals (Sweden)

KIM YANGKYUN

2010-12-01

Full Text Available This paper describes the computational analysis and visualization of flow around the model of a commercial airplane, Boeing 747-400. The geometry was realized through reverse engineering technique based on the photo scanning measurement. The steady three-dimensional viscous compressible governing equations were solved in the unstructured grid system. The basic conditions for computation were chosen as the same to those of Boeing 747-400’s cruising state. The high Reynolds turbulence models are tried. The angle of attack is varied to investigate the effect of the flight conditions to the aerodynamic performance. And flow and aerodynamic characteristics due to the existence of winglet were compared.

78 FR 43839 - Airworthiness Directives; the Boeing Company

Science.gov (United States)

2013-07-22

.... Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New... AD, contact Boeing Commercial Airplanes, Attention: Data & Services Management, P. O. Box 3707, MC 2H..., performed in accordance with Part 4 and Figure 8 of this service bulletin. This service information is being...

78 FR 14644 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2013-03-07

... support clamps installed within the left environmental control systems (ECS) bay, which could allow wiring... the installation of winglets per Supplemental Type Certificate (STC) ST00830SE ( http://rgl.faa.gov... Change the ``Parts Installation Prohibition'' Section Boeing requested the ``Parts Installation...

77 FR 38547 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2012-06-28

... (including cracking, misdrilled fastener holes, elongated fastener holes, corrosion, oil-cans, and existing..., corrosion, oil-cans, and existing repairs), or for certain discrepancies, contacting Boeing for repair... Designated Engineering Representative (DER). We have revised the date of the document specified in paragraph...

77 FR 5195 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2012-02-02

...). Support for Proposed Actions United Parcel Service Co. (UPS) supports mandating the Stage 2 inspections...., Washington, DC 20590, between 9 a.m. and 5 p.m., Monday through Friday, except Federal holidays. For service information identified in this proposed AD, contact Boeing Commercial Airplanes, Attention: Data & Services...

77 FR 49708 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2012-08-17

.... ADDRESSES: For service information identified in this AD, contact Boeing Commercial Airplanes, Attention.... Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New... Figure 24 as an accepted procedure'' for the HFEC inspection, this AD requires that the inspection be...

77 FR 47267 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2012-08-08

... contained within those paragraphs. Request To Clarify Undefined Requirement UPS stated that the actions... modification, which is currently undefined in Boeing Service Bulletin 747 53A2559, Revision 1, dated August 4... believe it will be affected; however, UPS is concerned with the precedent of mandating undefined...

78 FR 26286 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2013-05-06

... the first post-modification high frequency eddy current (HFEC) repetitive inspection may be extended... Boeing (the original equipment manufacturer) had time to build up an adequate stock of kits and/or frames.... We have also revised paragraph (g) in this supplemental NPRM to correspond to the manufacturer's...

78 FR 31389 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2013-05-24

... ``New Inspections and Corrective Actions to Ensure Cross Beam Reinforcement,'' and suggested language... door. Boeing added that the current language in the NPRM and this service information leave open the...) of this AD. (i) For airplanes with line numbers 1 through 1231 inclusive: Install a cross beam repair...

78 FR 68693 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2013-11-15

... Special Attention Service Bulletin 737-53-1296, dated January 11, 2011, in Step 1, ``Move,'' of Figure 10.... ADDRESSES: For service information identified in this AD, contact Boeing Commercial Airplanes, Attention... Facility, U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12...

77 FR 60285 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2012-10-03

... the MLG for chicken- wire cracks, corrosion, and chrome plate distress; repetitive magnetic particle..., contact Boeing Commercial Airplanes, Attention: Data & Services Management, P.O. Box 3707, MC 2H-65... magnetic particle inspections of the outer diameter chrome on the center axles of the MLG for cracks; and...

75 FR 12657 - Airworthiness Directives; The Boeing Company Model 777-200, -200LR, -300, -300ER, and 777F Series...

Science.gov (United States)

2010-03-17

..., Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC 20590. Hand Delivery: U.S. Department of... Boeing Company has also discovered during flight simulations that the climb gradient is less than optimal... bulletin describes procedures for installing new operational program software for the left, center, and...

76 FR 24349 - Airworthiness Directives; The Boeing Company Model 747-200B, -300, -400, -400D, and -400F Series...

Science.gov (United States)

2011-05-02

... this AD, contact Boeing Commercial Airplanes, Attention: Data & Services Management, P.O. Box 3707, MC.... Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New... to this issue. Request To Clarify Figures in Service Information UPS requested that we clarify the...

77 FR 63714 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2012-10-17

.... ACTION: Final rule. SUMMARY: We are adopting a new airworthiness directive (AD) for certain The Boeing... instructions and doing the work specified in those instructions. We are issuing this AD to detect and correct..., Room W12-140, 1200 New Jersey Avenue SE., Washington, DC 20590. FOR FURTHER INFORMATION CONTACT: Kelly...

78 FR 57053 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2013-09-17

... Boeing Commercial Airplanes, Attention: Data & Services Management, P.O. Box 3707, MC 2H-65, Seattle, WA... Management Facility, U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor... frame from stringers 23 through 31 per Figure 5 or Figure 6 of the service bulletins specified in...

77 FR 52212 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2012-08-29

... request to revise this AD. The inspections specified in Figure 1 in both Boeing Special Attention Service... Commercial Airplanes, Attention: Data & Services Management, P. O. Box 3707, MC 2H-65, Seattle, Washington... Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE., Washington, DC 20590. FOR FURTHER...

78 FR 14469 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2013-03-06

...-2251. Mail: U.S. Department of Transportation, Docket Operations, M-30, West Building Ground Floor... identified in this proposed AD, contact Boeing Commercial Airplanes, Attention: Data & Services Management, P... through 31 per Figure 5 or Figure 6 of the service bulletins specified in paragraph (g) or (h) of this AD...

77 FR 54854 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2012-09-06

.... Department of Transportation, Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New... 5 p.m., Monday through Friday, except Federal holidays. Boeing Commercial Airplanes, Attention: Data... airplanes), except as specified in paragraphs (h)(1) and (h)(2) of this AD. (1) Steps 1 through 5 of Figure...

77 FR 16188 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2012-03-20

..., M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE., Washington, DC 20590... Airplanes, Attention: Data & Services Management, P. O. Box 3707, MC 2H-65, Seattle, Washington 98124-2207... AD would require repair using a method approved in accordance with paragraph (l). Figure 1 of Boeing...

78 FR 60660 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2013-10-02

... compound (CIC) Boeing Material Specification (BMS) 3-23 to the surfaces of the repaired area. As an option... fracture and failure of the skin panels of the fuselage, and consequent rapid decompression of the airplane... availability of this material at the FAA, call 425-227-1221. Examining the AD Docket You may examine the AD...

78 FR 61161 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2013-10-03

... bolts being fabricated from bar stock with a machined head instead of from a forged blank with an upset... are issuing this AD to prevent damage to the MLG and consequent damage to airplane structure, which...'' fabrication. Boeing stated that it approved the fabrication of the bolts from bar stock with a machined head...

78 FR 66254 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2013-11-05

... AD. Costs of Compliance We estimate that this AD affects 84 airplanes of U.S. registry. We estimate... inspection cycle. We have received no definitive data that would enable us to provide a cost estimate for the... 2 of paragraph 1.E., ``Compliance,'' of Boeing Service Bulletin 747-53A2688, Revision 1, dated...

75 FR 52907 - Airworthiness Directives; The Boeing Company Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747...

Science.gov (United States)

2010-08-30

... CONTACT: Nicholas Han, Aerospace Engineer, Airframe Branch, ANM-120S, FAA, Seattle Aircraft Certification... Airlines (JAL) reports that certain structures prevented the accomplishment of the inspection specified in... time for certain inspection locations. Boeing reports that recent engineering analysis has revealed...

78 FR 73744 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2013-12-09

... paragraph (g) of this second SNPRM. Costs of Compliance We estimate that this proposed AD affects 1,147... 2,975 3,412,325 = $1,445. We have received no definitive data that would enable us to provide a cost... to be a rotable part, we note that Boeing Document D042A525, ``Compliance Document and Repair...

77 FR 64711 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2012-10-23

... Service Bulletin 737-22A1224, dated May 18, 2012, requires installation of FCC software P/N 2274-COL-AC1..., 2010, because that service bulletin only specifies to install FCC OPS software P/N 2276-COL-AC1-05 or P...) Install software identified in table 2 of the Accomplishment Instructions of Boeing Alert Service Bulletin...

75 FR 10669 - Airworthiness Directives; The Boeing Company Model 747-100, 747-200B, 747-300, and 747SR Series...

Science.gov (United States)

2010-03-09

... base assembly to the moisture shroud as given in Figure 10 in Boeing Alert Service Bulletin 747- 25A3368, Revision 2, dated June 12, 2008, and to fill any unused pilot holes in the mounting base assembly... 25, 2007, and to fill any unused pilot holes in the mounting base assembly in accordance with the...

78 FR 22439 - Airworthiness Directives; The Boeing Company Airplanes

Science.gov (United States)

2013-04-16

..., West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue SE., Washington, DC 20590. Hand..., Attention: Data & Services Management, P. O. Box 3707, MC 2H-65, Seattle, WA 98124-2207; phone: 206-544-5000... SRM 53-30-1, Figures 20, 21, 31, or 32; and Boeing 737-300/-400/-500 SRM 53-10-01, Repair 5, 6, or 8...

75 FR 61337 - Airworthiness Directives; The Boeing Company Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747...

Science.gov (United States)

2010-10-05

..., contact Boeing Commercial Airplanes, Attention: Data & Services Management, P.O. Box 3707, MC 2H-65..., Docket Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE...-60-15, Figure 201, Repair 5, do the inspection, including the threshold and intervals in accordance...

75 FR 27424 - Airworthiness Directives; The Boeing Company Model 747-100, 747-100B, 747-100B SUD, 747-200B, 747...

Science.gov (United States)

2010-05-17

... Boeing Commercial Airplanes, Attention: Data & Services Management, P.O. Box 3707, MC 2H-65, Seattle... Operations, M-30, West Building Ground Floor, Room W12-140, 1200 New Jersey Avenue, SE., Washington, DC 20590... reviewed the figures we have used over the past several years to calculate AD costs to operators. To...

Aeroacoustic Study of a 26%-Scale Semispan Model of a Boeing 777 Wing in the NASA Ames 40- by 80-Foot Wind Tunnel

Science.gov (United States)

Horne, W. Clifton; Burnside, Nathan J.; Soderman, Paul T.; Jaeger, Stephen M.; Reinero, Bryan R.; James, Kevin D.; Arledge, Thomas K.

2004-01-01

An acoustic and aerodynamic study was made of a 26%-scale unpowered Boeing 777 aircraft semispan model in the NASA Ames 40- by 80-Foot Wind Tunnel for the purpose of identifying and attenuating airframe noise sources. Simulated approach and landing configurations were evaluated at Mach numbers between 0.12 and 0.24. Cruise configurations were evaluated at Mach numbers between 0.24 and 0.33. The research team used two Ames phased-microphone arrays, a large fixed array and a small traversing array, mounted under the wing to locate and compare various noise sources in the wing high-lift system and landing gear. Numerous model modifications and noise alleviation devices were evaluated. Simultaneous with acoustic measurements, aerodynamic forces were recorded to document aircraft conditions and any performance changes caused by the geometric modifications. Numerous airframe noise sources were identified that might be important factors in the approach and landing noise of the full-scale aircraft. Several noise-control devices were applied to each noise source. The devices were chosen to manipulate and control, if possible, the flow around the various tips and through the various gaps of the high-lift system so as to minimize the noise generation. Fences, fairings, tip extensions, cove fillers, vortex generators, hole coverings, and boundary-layer trips were tested. In many cases, the noise-control devices eliminated noise from some sources at specific frequencies. When scaled to full-scale third-octave bands, typical noise reductions ranged from 1 to 10 dB without significant aerodynamic performance loss.

Boeing's STAR-FODB test results

Science.gov (United States)

Fritz, Martin E.; de la Chapelle, Michael; Van Ausdal, Arthur W.

1995-05-01

Boeing has successfully concluded a 2 1/2 year, two phase developmental contract for the STAR-Fiber Optic Data Bus (FODB) that is intended for future space-based applications. The first phase included system analysis, trade studies, behavior modeling, and architecture and protocal selection. During this phase we selected AS4074 Linear Token Passing Bus (LTPB) protocol operating at 200 Mbps, along with the passive, star-coupled fiber media. The second phase involved design, build, integration, and performance and environmental test of brassboard hardware. The resulting brassboard hardware successfully passed performance testing, providing 200 Mbps operation with a 32 X 32 star-coupled medium. This hardware is suitable for a spaceflight experiment to validate ground testing and analysis and to demonstrate performace in the intended environment. The fiber bus interface unit (FBIU) is a multichip module containing transceiver, protocol, and data formatting chips, buffer memory, and a station management controller. The FBIU has been designed for low power, high reliability, and radiation tolerance. Nine FBIUs were built and integrated with the fiber optic physical layer consisting of the fiber cable plant (FCP) and star coupler assembly (SCA). Performance and environmental testing, including radiation exposure, was performed on selected FBIUs and the physical layer. The integrated system was demonstrated with a full motion color video image transfer across the bus while simultaneously performing utility functions with a fiber bus control module (FBCM) over a telemetry and control (T&C) bus, in this case AS1773.

77 FR 1618 - Special Conditions: The Boeing Company, Model 767-300; Seats With Inflatable Lapbelts

Science.gov (United States)

2012-01-11

... energy absorption throughout that range of occupants. In addition, the following situations must be... these special conditions effective upon issuance. Comments Invited We invite interested people to take...

Salapärane Boeing tõi Eestisse konteinereid / Ester Vilgats

Index Scriptorium Estoniae

Vilgats, Ester

2005-01-01

Ilmunud ka: Pärnu Postimees 8. nov., lk. 3, Postimees : na russkom jazõke 10. nov. lk. 10. Pärnu lennujaama juhataja Erki Teemägi ja Kaitsepolitsei Pärnu osakonna politseidirektor Kalev Kont kinnitasid, et Pärnu lennuväljal 12. jaanuaril 2003. aastal maandunud Boeing 737 vedas kaubakonteinereid, mitte terroristidest sõjavange, nagu väitis ajaleht Washington Post. Vt. samas: Neeme Raud. Inimõiguslased ootavad euroliidu sekkumist

Advanced composite elevator for Boeing 727 aircraft

Science.gov (United States)

1979-01-01

Detail design activities are reported for a program to develop an advanced composites elevator for the Boeing 727 commercial transport. Design activities include discussion of the full scale ground test and flight test activities, the ancillary test programs, sustaining efforts, weight status, and the production status. Prior to flight testing of the advanced composites elevator, ground, flight flutter, and stability and control test plans were reviewed and approved by the FAA. Both the ground test and the flight test were conducted according to the approved plan, and were witnessed by the FAA. Three and one half shipsets have now been fabricated without any significant difficulty being encountered. Two elevator system shipsets were weighed, and results validated the 26% predicted weight reduction. The program is on schedule.

76 FR 63818 - Special Conditions: Boeing Model 767-400ER Series Airplanes; Seats With Inflatable Lapbelts

Science.gov (United States)

2011-10-14

... inflatable lapbelt must provide a consistent approach to energy absorption throughout that range of occupants... special conditions effective upon issuance. Comments Invited We invite interested people to take part in...

Advanced composite elevator for Boeing 727 aircraft. Volume 1: Technical summary

Science.gov (United States)

Chovil, D. V.; Harvey, S. T.; Mccarty, J. E.; Desper, O. E.; Jamison, E. S.; Syder, H.

1981-01-01

The design, development, analysis, and testing activities and results that were required to produce five and one-half shipsets of advanced composite elevators for Boeing 727 aircraft are summarized. During the preliminary design period, alternative concepts were developed. After selection of the best design, detail design and basic configuration improvements were evaluated. Five and one-half shipsets were manufactured. All program goals (except competitive cost demonstration) were accomplished when our design met or exceeded all requirements, criteria, and objectives.

77 FR 16910 - Special Conditions: Boeing Model 787 Series Airplanes; Single-place Side-facing Seats With...

Science.gov (United States)

2012-03-23

... structure such as an interior wall or furnishing that will support the pelvis, upper arm, chest, and head of... stiffness must be included in the tests. 3. Thoracic Trauma: Under the load condition defined in Sec. 25.562(b)(2), Thoracic Trauma Index (TTI) injury criterion must be substantiated by dynamic test or by...

STS-65 crewmembers participate in bench review at Boeing Building

Science.gov (United States)

1994-01-01

Attired in clean suits, STS-65 Payload Commander (PLC) Richard J. Hieb (left) and Payload Specialist Chiaki Mukai examine the contents of a stowage locker during a bench review at Boeing's Flight Equipment Processing Facility (FEPF) near the Johnson Space Center (JSC). In the background, Commander Robert D. Cabana inspects additional equipment to be carried aboard the Space Shuttle Columbia, Orbiter Vehicle (OV) 102, for the scheduled July flight of the second International Microgravity Laboratory (IML-2) mission. Mukai represents Japan's National Space Development Agency (NASDA). Photo taken by NASA JSC contract photographer Scott A. Wickes.

Full-scale testing, production and cost analysis data for the advanced composite stabilizer for Boeing 737 aircraft, volume 2

Science.gov (United States)

Aniversario, R. B.; Harvey, S. T.; Mccarty, J. E.; Parson, J. T.; Peterson, D. C.; Pritchett, L. D.; Wilson, D. R.; Wogulis, E. R.

1982-01-01

The development, testing, production activities, and associated costs that were required to produce five-and-one-half advanced-composite stabilizer shipsets for Boeing 737 aircraft are defined and discussed.

Site Environmental Report for Calendar Year 1999. DOE Operations at The Boeing Company, Rocketdyne

Energy Technology Data Exchange (ETDEWEB)

None

2000-09-01

OAK A271 Site Environmental Report for Calendar Year 1999. DOE Operations at The Boeing Company, Rocketdyne. This Annual Site Environmental Report (ASER) for 1999 describes the environmental conditions related to work performed for the Department of Energy (DOE) at Area IV of the Rocketdyne Santa Susana Field Laboratory (SSFL). In the past, these operations included development, fabrication, and disassembly of nuclear reactors, reactor fuel, and other radioactive materials under the former Atomics International Division. Other activities included the operation of large-scale liquid metal facilities for testing of liquid metal fast breeder components at the Energy Technology Engineering Center (ETEC), a government-owned, company-operated test facility within Area IV. All nuclear work was terminated in 1988, and subsequently, all radiological work has been directed toward decontamination and decommissioning (D&D) of the previously used nuclear facilities and associated site areas. Large-scale D&D activities of the sodium test facilities began in 1996. This Annual Site Environmental Report provides information showing that there are no indications of any potential impact on public health and safety due to the operations conducted at the SSFL. All measures and calculations of off-site conditions demonstrate compliance with applicable regulations, which provide for protection of human health and the environment.

Site Environmental Report for Calendar Year 1999. DOE Operations at The Boeing Company, Rocketdyne

International Nuclear Information System (INIS)

None

2000-01-01

OAK A271 Site Environmental Report for Calendar Year 1999. DOE Operations at The Boeing Company, Rocketdyne. This Annual Site Environmental Report (ASER) for 1999 describes the environmental conditions related to work performed for the Department of Energy (DOE) at Area IV of the Rocketdyne Santa Susana Field Laboratory (SSFL). In the past, these operations included development, fabrication, and disassembly of nuclear reactors, reactor fuel, and other radioactive materials under the former Atomics International Division. Other activities included the operation of large-scale liquid metal facilities for testing of liquid metal fast breeder components at the Energy Technology Engineering Center (ETEC), a government-owned, company-operated test facility within Area IV. All nuclear work was terminated in 1988, and subsequently, all radiological work has been directed toward decontamination and decommissioning (D and D) of the previously used nuclear facilities and associated site areas. Large-scale D and D activities of the sodium test facilities began in 1996. This Annual Site Environmental Report provides information showing that there are no indications of any potential impact on public health and safety due to the operations conducted at the SSFL. All measures and calculations of off-site conditions demonstrate compliance with applicable regulations, which provide for protection of human health and the environment

75 FR 2434 - Special Conditions: Boeing Model 747-8/-8F Series Airplanes; Design Roll Maneuver Requirement

Science.gov (United States)

2010-01-15

... result from defined movements of the cockpit roll control as opposed to defined aileron deflections. Also... limited to the roll axis only, whereas previous special conditions also included pitch and yaw axes. A... movement of the cockpit roll control up to the limit is assumed. The position of the cockpit roll control...

Modelling classroom conditions with different boundary conditions

DEFF Research Database (Denmark)

Marbjerg, Gerd Høy; Jeong, Cheol-Ho; Brunskog, Jonas

2014-01-01

A model that combines image source modelling and acoustical radiosity with complex boundary condition, thus including phase shifts on reflection has been developed. The model is called PARISM (Phased Acoustical Radiosity and Image Source Model). It has been developed in order to be able to model...

The DoD C-17 Versus the Boeing 777. A Comparison of Acquisition and Development

Science.gov (United States)

1999-10-01

Standard Encyclopedia (New York: Unicorn Publishers, 1955), 102-103. 9. The World Book Encyclopedia (Kansas City, MO: Field Enterprises Educational...costs about $25.25 per mile to operate--including insurance, administration, and financing . The amount is similar for the MD-11 and Airbus A340-300X, 9...resources that include investments, income from operations (airplane sales), or outside financing . Although Boeing customarily receives a deposit

Relative efficiency of joint-model and full-conditional-specification multiple imputation when conditional models are compatible: The general location model.

Science.gov (United States)

Seaman, Shaun R; Hughes, Rachael A

2018-06-01

Estimating the parameters of a regression model of interest is complicated by missing data on the variables in that model. Multiple imputation is commonly used to handle these missing data. Joint model multiple imputation and full-conditional specification multiple imputation are known to yield imputed data with the same asymptotic distribution when the conditional models of full-conditional specification are compatible with that joint model. We show that this asymptotic equivalence of imputation distributions does not imply that joint model multiple imputation and full-conditional specification multiple imputation will also yield asymptotically equally efficient inference about the parameters of the model of interest, nor that they will be equally robust to misspecification of the joint model. When the conditional models used by full-conditional specification multiple imputation are linear, logistic and multinomial regressions, these are compatible with a restricted general location joint model. We show that multiple imputation using the restricted general location joint model can be substantially more asymptotically efficient than full-conditional specification multiple imputation, but this typically requires very strong associations between variables. When associations are weaker, the efficiency gain is small. Moreover, full-conditional specification multiple imputation is shown to be potentially much more robust than joint model multiple imputation using the restricted general location model to mispecification of that model when there is substantial missingness in the outcome variable.

Modelling Multivariate Autoregressive Conditional Heteroskedasticity with the Double Smooth Transition Conditional Correlation GARCH Model

DEFF Research Database (Denmark)

Silvennoinen, Annastiina; Teräsvirta, Timo

In this paper we propose a multivariate GARCH model with a time-varying conditional correlation structure. The new Double Smooth Transition Conditional Correlation GARCH model extends the Smooth Transition Conditional Correlation GARCH model of Silvennoinen and Ter¨asvirta (2005) by including...... another variable according to which the correlations change smoothly between states of constant correlations. A Lagrange multiplier test is derived to test the constancy of correlations against the DSTCC-GARCH model, and another one to test for another transition in the STCC-GARCH framework. In addition......, other specification tests, with the aim of aiding the model building procedure, are considered. Analytical expressions for the test statistics and the required derivatives are provided. The model is applied to a selection of world stock indices, and it is found that time is an important factor affecting...

Static and wind tunnel near-field/far-field jet noise measurements from model scale single-flow base line and suppressor nozzles. Summary report. [conducted in the Boeing large anechoic test chamber and the NASA-Ames 40by 80-foot wind tunnel

Science.gov (United States)

Jaeck, C. L.

1977-01-01

A test program was conducted in the Boeing large anechoic test chamber and the NASA-Ames 40- by 80-foot wind tunnel to study the near- and far-field jet noise characteristics of six baseline and suppressor nozzles. Static and wind-on noise source locations were determined. A technique for extrapolating near field jet noise measurements into the far field was established. It was determined if flight effects measured in the near field are the same as those in the far field. The flight effects on the jet noise levels of the baseline and suppressor nozzles were determined. Test models included a 15.24-cm round convergent nozzle, an annular nozzle with and without ejector, a 20-lobe nozzle with and without ejector, and a 57-tube nozzle with lined ejector. The static free-field test in the anechoic chamber covered nozzle pressure ratios from 1.44 to 2.25 and jet velocities from 412 to 594 m/s at a total temperature of 844 K. The wind tunnel flight effects test repeated these nozzle test conditions with ambient velocities of 0 to 92 m/s.

Influence of Machine-Derived Smoke Yields on Biomarker of Exposure (BOE Levels in Cigarette Smokers*

Directory of Open Access Journals (Sweden)

Scherer Gerhard

2015-01-01

Full Text Available Individual uptake of tobacco smoke constituents by smoking is highly variable in cigarette smokers and cannot be predicted by smoking behaviour variables and machine-derived smoke yields. It is well established that uptake of smoke constituents is best described by a series of bio-markers of exposure (BOEs such as metabolites of nico-tine, tobacco-specific nitrosamines (TSNAs, polycyclic aromatic hydrocarbons (PAHs, aromatic amines, benzene, 1,3-butadiene, acrolein, hydrogen cyanide, 2,5-dimethyl-furan and other smoke constituents.

STS-65 crewmembers and backup participate in bench review at Boeing Building

Science.gov (United States)

1994-01-01

STS-65 crewmembers, wearing clean suits, look over equipment to be carried aboard the Space Shuttle Columbia, Orbiter Vehicle (OV) 102, for the scheduled July flight of the second International Microgravity Laboratory (IML-2) mission. Surrounding a table full of equipment at Boeing's Flight Equipment Processing Facility near the Johnson Space Center (JSC), are (left to right) Mission Specialist (MS) Leroy Chiao, MS Donald A. Thomas, Commander Robert D. Cabana, Payload Specialist Chiaki Mukai, Payload Commander (PLC) Richard J. Hieb, and backup (alternate) payload specialist Jean-Jacques Favier. Mukai represents Japan's National Space Development Agency (NASDA) and Favier represents France's Centre National d'Etudes Spatiales. Photo taken by NASA JSC contract photographer Scott A. Wickes.

Conditional Poisson models: a flexible alternative to conditional logistic case cross-over analysis.

Science.gov (United States)

Armstrong, Ben G; Gasparrini, Antonio; Tobias, Aurelio

2014-11-24

The time stratified case cross-over approach is a popular alternative to conventional time series regression for analysing associations between time series of environmental exposures (air pollution, weather) and counts of health outcomes. These are almost always analyzed using conditional logistic regression on data expanded to case-control (case crossover) format, but this has some limitations. In particular adjusting for overdispersion and auto-correlation in the counts is not possible. It has been established that a Poisson model for counts with stratum indicators gives identical estimates to those from conditional logistic regression and does not have these limitations, but it is little used, probably because of the overheads in estimating many stratum parameters. The conditional Poisson model avoids estimating stratum parameters by conditioning on the total event count in each stratum, thus simplifying the computing and increasing the number of strata for which fitting is feasible compared with the standard unconditional Poisson model. Unlike the conditional logistic model, the conditional Poisson model does not require expanding the data, and can adjust for overdispersion and auto-correlation. It is available in Stata, R, and other packages. By applying to some real data and using simulations, we demonstrate that conditional Poisson models were simpler to code and shorter to run than are conditional logistic analyses and can be fitted to larger data sets than possible with standard Poisson models. Allowing for overdispersion or autocorrelation was possible with the conditional Poisson model but when not required this model gave identical estimates to those from conditional logistic regression. Conditional Poisson regression models provide an alternative to case crossover analysis of stratified time series data with some advantages. The conditional Poisson model can also be used in other contexts in which primary control for confounding is by fine

76 FR 57625 - Special Conditions: Boeing Model 737-600, -700, -700C, -800, -900, and -900ER Series Airplanes...

Science.gov (United States)

2011-09-16

... addition, the substance of these special conditions has been subject to the public-comment process in...-battery cells use flammable liquid electrolytes. The electrolyte can serve as a source of fuel for an.... 25.1353 that are applicable to lithium batteries. The flammable-fluid fire-protection requirements of...

Analysis of Limit Cycle Oscillation Data from the Aeroelastic Test of the SUGAR Truss-Braced Wing Model

Science.gov (United States)

Bartels, Robert E.; Funk, Christie; Scott, Robert C.

2015-01-01

Research focus in recent years has been given to the design of aircraft that provide significant reductions in emissions, noise and fuel usage. Increases in fuel efficiency have also generally been attended by overall increased wing flexibility. The truss-braced wing (TBW) configuration has been forwarded as one that increases fuel efficiency. The Boeing company recently tested the Subsonic Ultra Green Aircraft Research (SUGAR) Truss-Braced Wing (TBW) wind-tunnel model in the NASA Langley Research Center Transonic Dynamics Tunnel (TDT). This test resulted in a wealth of accelerometer data. Other publications have presented details of the construction of that model, the test itself, and a few of the results of the test. This paper aims to provide a much more detailed look at what the accelerometer data says about the onset of aeroelastic instability, usually known as flutter onset. Every flight vehicle has a location in the flight envelope of flutter onset, and the TBW vehicle is not different. For the TBW model test, the flutter onset generally occurred at the conditions that the Boeing company analysis said it should. What was not known until the test is that, over a large area of the Mach number dynamic pressure map, the model displayed wing/engine nacelle aeroelastic limit cycle oscillation (LCO). This paper dissects that LCO data in order to provide additional insights into the aeroelastic behavior of the model.

Evaluating stress analysis and failure criteria for offshore structures for Pechora Sea conditions

Science.gov (United States)

Nesic, S.; Donskoy, Y.; Zolotukhin, A.

2017-12-01

Development of Arctic hydrocarbon resources has faced many challenges due to sensitive environmental conditions including low temperatures, ice cover and terrestrial permafrost and extreme seasonal variation in sunlight. Russian offshore field development in Arctic region is usually associated with annual ice cover, which can cause serious damage on the offshore platforms. The Pechora Sea has claimed as one of the most perspective oil and gas region of the Russian Arctic with seven discovered oil and gas fields and several dozens of structures. Our rough assessment, based on in-place hydrocarbon volumes and recovery factor evaluation concept, indicates that Pechora Sea alone has in-place volumes amounting to ca. 20 billion barrel oil equivalent (BOE). This quantity is enough to secure produced volumes by 2040 exceeding 3 billion BOE [1] that indicates huge resource potential of the region. The environmental conditions are primarily function of water dynamics and ice cover. The sea is covered by the ice for greatest part of the year. In this article, the ice load simulations were performed using explicit dynamic analysis system in ANSYS software to determine best shape and size of an offshore platform for the Pechora Sea ice conditions. Different gravity based structures (GBS) were analyzed: artificial island, hollow cylindrical and conical concrete structures and four-leg GBS. Relationships between the stress, deformations and time were analyzed and important observations from the simulation results were a basis for selecting the most preferable structures.

Full-scale testing, production and cost analysis data for the advanced composite stabilizer for Boeing 737 aircraft. Volume 1: Technical summary

Science.gov (United States)

Aniversario, R. B.; Harvey, S. T.; Mccarty, J. E.; Parsons, J. T.; Peterson, D. C.; Pritchett, L. D.; Wilson, D. R.; Wogulis, E. R.

1983-01-01

The full scale ground test, ground vibration test, and flight tests conducted to demonstrate a composite structure stabilizer for the Boeing 737 aircraft and obtain FAA certification are described. Detail tools, assembly tools, and overall production are discussed. Cost analyses aspects covered include production costs, composite material usage factors, and cost comparisons.

Conditional Correlation Models of Autoregressive Conditional Heteroskedasticity with Nonstationary GARCH Equations

DEFF Research Database (Denmark)

Amado, Cristina; Teräsvirta, Timo

-run and the short-run dynamic behaviour of the volatilities. The structure of the conditional correlation matrix is assumed to be either time independent or to vary over time. We apply our model to pairs of seven daily stock returns belonging to the S&P 500 composite index and traded at the New York Stock Exchange......In this paper we investigate the effects of careful modelling the long-run dynamics of the volatilities of stock market returns on the conditional correlation structure. To this end we allow the individual unconditional variances in Conditional Correlation GARCH models to change smoothly over time...... by incorporating a nonstationary component in the variance equations. The modelling technique to determine the parametric structure of this time-varying component is based on a sequence of specification Lagrange multiplier-type tests derived in Amado and Teräsvirta (2011). The variance equations combine the long...

Extreme Conditions Modeling Workshop Report

Energy Technology Data Exchange (ETDEWEB)

Coe, R. G.; Neary, V. S.; Lawson, M. J.; Yu, Y.; Weber, J.

2014-07-01

Sandia National Laboratories (SNL) and the National Renewable Energy Laboratory (NREL) hosted the Wave Energy Converter (WEC) Extreme Conditions Modeling (ECM) Workshop in Albuquerque, NM on May 13th-14th, 2014. The objective of the workshop was to review the current state of knowledge on how to model WECs in extreme conditions (e.g. hurricanes and other large storms) and to suggest how U.S. Department of Energy (DOE) and national laboratory resources could be used to improve ECM methods for the benefit of the wave energy industry.

Comment paper: Workshop on Engineering Turbulence Modeling

Science.gov (United States)

Spalart, P. R.

1992-01-01

The speaker for this paper describes and evaluates a k-epsilon model for calculating Samuel-Joubert flow. He proceeds to present both Boeing's and his positions on the state-of-the-art in this area and future goals. Finally, presented is a one equation mathematical model for calculating Samuel-Joubert flow. All results are presented in viewgraph format.

Nonlinear models for autoregressive conditional heteroskedasticity

DEFF Research Database (Denmark)

Teräsvirta, Timo

This paper contains a brief survey of nonlinear models of autore- gressive conditional heteroskedasticity. The models in question are parametric nonlinear extensions of the original model by Engle (1982). After presenting the individual models, linearity testing and parameter estimation are discu...

Development of plant condition measurement - The Jimah Model

Science.gov (United States)

Evans, Roy F.; Syuhaimi, Mohd; Mazli, Mohammad; Kamarudin, Nurliyana; Maniza Othman, Faiz

2012-05-01

The Jimah Model is an information management model. The model has been designed to facilitate analysis of machine condition by integrating diagnostic data with quantitative and qualitative information. The model treats data as a single strand of information - metaphorically a 'genome' of data. The 'Genome' is structured to be representative of plant function and identifies the condition of selected components (or genes) in each machine. To date in industry, computer aided work processes used with traditional industrial practices, have been unable to consistently deliver a standard of information suitable for holistic evaluation of machine condition and change. Significantly the reengineered site strategies necessary for implementation of this "data genome concept" have resulted in enhanced knowledge and management of plant condition. In large plant with high initial equipment cost and subsequent high maintenance costs, accurate measurement of major component condition becomes central to whole of life management and replacement decisions. A case study following implementation of the model at a major power station site in Malaysia (Jimah) shows that modeling of plant condition and wear (in real time) can be made a practical reality.

Development of plant condition measurement - The Jimah Model

International Nuclear Information System (INIS)

Evans, Roy F; Syuhaimi, Mohd; Mazli, Mohammad; Kamarudin, Nurliyana; Othman, Faiz Maniza

2012-01-01

The Jimah Model is an information management model. The model has been designed to facilitate analysis of machine condition by integrating diagnostic data with quantitative and qualitative information. The model treats data as a single strand of information - metaphorically a 'genome' of data. The 'Genome' is structured to be representative of plant function and identifies the condition of selected components (or genes) in each machine. To date in industry, computer aided work processes used with traditional industrial practices, have been unable to consistently deliver a standard of information suitable for holistic evaluation of machine condition and change. Significantly the reengineered site strategies necessary for implementation of this 'data genome concept' have resulted in enhanced knowledge and management of plant condition. In large plant with high initial equipment cost and subsequent high maintenance costs, accurate measurement of major component condition becomes central to whole of life management and replacement decisions. A case study following implementation of the model at a major power station site in Malaysia (Jimah) shows that modeling of plant condition and wear (in real time) can be made a practical reality.

Modeling conditional correlations of asset returns

DEFF Research Database (Denmark)

Silvennoinen, Annastiina; Teräsvirta, Timo

2015-01-01

In this paper we propose a new multivariate GARCH model with time-varying conditional correlation structure. The time-varying conditional correlations change smoothly between two extreme states of constant correlations according to a predetermined or exogenous transition variable. An LM-test is d......In this paper we propose a new multivariate GARCH model with time-varying conditional correlation structure. The time-varying conditional correlations change smoothly between two extreme states of constant correlations according to a predetermined or exogenous transition variable. An LM......-test is derived to test the constancy of correlations and LM- and Wald tests to test the hypothesis of partially constant correlations. Analytical expressions for the test statistics and the required derivatives are provided to make computations feasible. An empirical example based on daily return series of five...

Testing the Conditional Mean Function of Autoregressive Conditional Duration Models

DEFF Research Database (Denmark)

Hautsch, Nikolaus

be subject to censoring structures. In an empirical study based on financial transaction data we present an application of the model to estimate conditional asset price change probabilities. Evaluating the forecasting properties of the model, it is shown that the proposed approach is a promising competitor......This paper proposes a dynamic proportional hazard (PH) model with non-specified baseline hazard for the modelling of autoregressive duration processes. A categorization of the durations allows us to reformulate the PH model as an ordered response model based on extreme value distributed errors...

Extreme Conditions Modeling Workshop Report

Energy Technology Data Exchange (ETDEWEB)

Coe, Ryan Geoffrey [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Neary, Vincent Sinclair [Sandia National Laboratories (SNL-NM), Albuquerque, NM (United States); Lawon, Michael J. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Yu, Yi-Hsiang [National Renewable Energy Lab. (NREL), Golden, CO (United States); Weber, Jochem [National Renewable Energy Lab. (NREL), Golden, CO (United States)

2014-07-01

Sandia National Laboratories (SNL) and the National Renewable Energy Laboratory (NREL) hosted the Wave Energy Converter (WEC) Extreme Conditions Modeling (ECM) Workshop in Albuquerque, New Mexico on May 13–14, 2014. The objective of the workshop was to review the current state of knowledge on how to numerically and experimentally model WECs in extreme conditions (e.g. large ocean storms) and to suggest how national laboratory resources could be used to improve ECM methods for the benefit of the wave energy industry. More than 30 U.S. and European WEC experts from industry, academia, and national research institutes attended the workshop, which consisted of presentations from W EC developers, invited keynote presentations from subject matter experts, breakout sessions, and a final plenary session .

An aircraft noise pollution model for trajectory optimization

Science.gov (United States)

Barkana, A.; Cook, G.

1976-01-01

A mathematical model describing the generation of aircraft noise is developed with the ultimate purpose of reducing noise (noise-optimizing landing trajectories) in terminal areas. While the model is for a specific aircraft (Boeing 737), the methodology would be applicable to a wide variety of aircraft. The model is used to obtain a footprint on the ground inside of which the noise level is at or above 70 dB.

RADIONUCLIDE TRANSPORT MODELS UNDER AMBIENT CONDITIONS

Energy Technology Data Exchange (ETDEWEB)

S. Magnuson

2004-11-01

The purpose of this model report is to document the unsaturated zone (UZ) radionuclide transport model, which evaluates, by means of three-dimensional numerical models, the transport of radioactive solutes and colloids in the UZ, under ambient conditions, from the repository horizon to the water table at Yucca Mountain, Nevada.

Modeling of fracture and durability of paste-bonded composite joints subjected to hygro-thermal-mechanical loading

Science.gov (United States)

Harris, David Lee

The objective of the research is to characterize the behavior of composite/composite joints with paste adhesive using both experimental testing and analytical modeling. In comparison with the conventional tape adhesive, joining composites using paste adhesive provides several advantages. The carbon fiber laminate material systems employed in this study included IM7 carbon fibers and 977-3 epoxy matrix assembled in prepreg tape, and AS4 carbon fibers and 977-3 epoxy matrix as a five-harness satin weave. The adhesive employed was EA 9394 epoxy. All laminates and test specimens were fabricated and inspected by Boeing using their standard propriety procedures. Three types of test specimens were used in the program. They were bonded double-lap shear (DLS), bonded double cantilever beam (DCB) and bonded interlaminar tension (ILT) specimens. A group of specimens were conditioned at elevated temperature and humidity in an environmental chamber at Boeing's facility and their moisture absorption recorded with time. Specimens were tested at room temperature dry and elevated temperatures. DCB and DLS specimens were tested in fatigue as well as static conditions. Two-dimensional finite element models of the three configurations were developed for determining stresses and strains using the ABAQUS finite element package code. Due to symmetry, only the one-half of the specimen needed to be considered thus reducing computational time. The effect of the test fixture is not taken into account instead equivalent distributed stresses are applied directly on the composite laminates. For each of the specimen, the distribution of Mises stress and the first strain invariant J1 are obtained to identify potential failure locations within a specimen.

Force Tests of the Boeing XB-47 Full-Scale Empennage in the Ames 40- by 80-Foot Wind Tunnel

Science.gov (United States)

Hunton, Lynn W.

1947-01-01

A wind-tunnel investigation of the Boeing XB-47 full-scale empennage was conducted to provide, prior to flight tests, data required on the effectiveness of the elevator and rudder. The XB-47 airplane is a jet-propelled medium bomber having wing and tail surfaces swept back 35 degrees. The investigation included tests of the effectiveness of the elevator with normal straight sides, with a buldged trailing edge, and with a modified hinge-line gap and tests of the effectiveness of the rudder with a normal straight-sided tab and with a bulged tab.

Nuclear containment structure subjected to commercial and fighter aircraft crash

International Nuclear Information System (INIS)

Sadique, M.R.; Iqbal, M.A.; Bhargava, P.

2013-01-01

Highlights: • Nuclear containment response has been studied against aircraft crash. • Concrete damaged plasticity and Johnson–Cook elasto-viscoplastic models were employed. • Boeing 747-400 and Boeing 767-400 aircrafts caused global failure of containment. • Airbus A320 and Boeing 707-320 aircrafts caused local damage. • Tension damage of concrete was found more prominent compared to compression damage. -- Abstract: The response of a boiling water reactor (BWR) nuclear containment vessel has been studied against commercial and fighter aircraft crash using a nonlinear finite element code ABAQUS. The aircrafts employed were Boeing 747-400, Boeing 767-400, Airbus A-320, Boeing 707-320 and Phantom F4. The containment was modeled as a three-dimensional deformable reinforced concrete structure while the loading of aircraft was assigned using the respective reaction–time curve. The location of strike was considered near the junction of dome and cylinder, and the angle of incidence, normal to the containment surface. The material behavior of the concrete was incorporated using the damaged plasticity model while that of the reinforcement, the Johnson–Cook elasto-viscoplastic model. The containment could not sustain the impact of Boeing 747-400 and Boeing 767-400 aircrafts and suffered rupture of concrete around the impact region leading to global failure. On the other hand, the maximum local deformation at the point of impact was found to be 0.998 m, 0.099 m, 0.092 m, 0.089 m, and 0.074 m against Boeing 747-400, Phantom F4, Boeing 767, Boeing 707-320 and Airbus A-320 aircrafts respectively. The results of the present study were compared with those of the previous analytical and numerical investigations with respect to the maximum deformation and overall behavior of the containment

Nuclear containment structure subjected to commercial and fighter aircraft crash

Energy Technology Data Exchange (ETDEWEB)

Sadique, M.R., E-mail: rehan.sadique@gmail.com; Iqbal, M.A., E-mail: iqbalfce@iitr.ernet.in; Bhargava, P., E-mail: bhpdpfce@iitr.ernet.in

2013-07-15

Highlights: • Nuclear containment response has been studied against aircraft crash. • Concrete damaged plasticity and Johnson–Cook elasto-viscoplastic models were employed. • Boeing 747-400 and Boeing 767-400 aircrafts caused global failure of containment. • Airbus A320 and Boeing 707-320 aircrafts caused local damage. • Tension damage of concrete was found more prominent compared to compression damage. -- Abstract: The response of a boiling water reactor (BWR) nuclear containment vessel has been studied against commercial and fighter aircraft crash using a nonlinear finite element code ABAQUS. The aircrafts employed were Boeing 747-400, Boeing 767-400, Airbus A-320, Boeing 707-320 and Phantom F4. The containment was modeled as a three-dimensional deformable reinforced concrete structure while the loading of aircraft was assigned using the respective reaction–time curve. The location of strike was considered near the junction of dome and cylinder, and the angle of incidence, normal to the containment surface. The material behavior of the concrete was incorporated using the damaged plasticity model while that of the reinforcement, the Johnson–Cook elasto-viscoplastic model. The containment could not sustain the impact of Boeing 747-400 and Boeing 767-400 aircrafts and suffered rupture of concrete around the impact region leading to global failure. On the other hand, the maximum local deformation at the point of impact was found to be 0.998 m, 0.099 m, 0.092 m, 0.089 m, and 0.074 m against Boeing 747-400, Phantom F4, Boeing 767, Boeing 707-320 and Airbus A-320 aircrafts respectively. The results of the present study were compared with those of the previous analytical and numerical investigations with respect to the maximum deformation and overall behavior of the containment.

A generalized conditional heteroscedastic model for temperature downscaling

Science.gov (United States)

Modarres, R.; Ouarda, T. B. M. J.

2014-11-01

This study describes a method for deriving the time varying second order moment, or heteroscedasticity, of local daily temperature and its association to large Coupled Canadian General Circulation Models predictors. This is carried out by applying a multivariate generalized autoregressive conditional heteroscedasticity (MGARCH) approach to construct the conditional variance-covariance structure between General Circulation Models (GCMs) predictors and maximum and minimum temperature time series during 1980-2000. Two MGARCH specifications namely diagonal VECH and dynamic conditional correlation (DCC) are applied and 25 GCM predictors were selected for a bivariate temperature heteroscedastic modeling. It is observed that the conditional covariance between predictors and temperature is not very strong and mostly depends on the interaction between the random process governing temporal variation of predictors and predictants. The DCC model reveals a time varying conditional correlation between GCM predictors and temperature time series. No remarkable increasing or decreasing change is observed for correlation coefficients between GCM predictors and observed temperature during 1980-2000 while weak winter-summer seasonality is clear for both conditional covariance and correlation. Furthermore, the stationarity and nonlinearity Kwiatkowski-Phillips-Schmidt-Shin (KPSS) and Brock-Dechert-Scheinkman (BDS) tests showed that GCM predictors, temperature and their conditional correlation time series are nonlinear but stationary during 1980-2000 according to BDS and KPSS test results. However, the degree of nonlinearity of temperature time series is higher than most of the GCM predictors.

Radionuclide Transport Models Under Ambient Conditions

International Nuclear Information System (INIS)

Moridis, G.; Hu, Q.

2001-01-01

The purpose of Revision 00 of this Analysis/Model Report (AMR) is to evaluate (by means of 2-D semianalytical and 3-D numerical models) the transport of radioactive solutes and colloids in the unsaturated zone (UZ) under ambient conditions from the potential repository horizon to the water table at Yucca Mountain (YM), Nevada

Assessment of slip factor models at off-design condition

International Nuclear Information System (INIS)

Yoon, Sung Ho; Baek, Je Hyun

2000-01-01

Slip factor is defined as an empirical factor being multiplied to theoretical energy transfer for the estimation of real work input of a centrifugal compressor. Researchers have tried to develop a simple empirical model, for a century, to predict a slip factor. However most these models were developed on the condition of design point assuming inviscid flow. So these models often fail to predict a correct slip factor at off-design condition. In this study, we summarized various slip factor models and compared these models with experimental and numerical data at off-design condition. As a result of this study, Wiesner's and Paeng and Chung's models are applicable for radial impeller, but all the models are not suitable for backswept impeller. Finally, the essential avenues for future study is discussed

76 FR 10476 - Special Conditions: Boeing Model 787-8 Airplane; Overhead Crew-Rest Compartment

Science.gov (United States)

2011-02-25

... should be used in determining placement of required fire extinguishers and protective breathing equipment... blockage, which might result from fire, mechanical or structural failure, or persons standing below or... ventilation rate. The system must have sufficient extinguishing agent to provide an initial knockdown and...

75 FR 75 - Special Conditions: Boeing Model 787-8 Airplane; Overhead Crew Rest Compartment

Science.gov (United States)

2010-01-04

... should be used in determining placement of required fire extinguishers and protective breathing equipment... the possibility of blockage, which might result from fire, mechanical or structural failure, or... capacity to suppress a fire considering the fire threat, the volume of the compartment, and the ventilation...

76 FR 35324 - Special Conditions: Boeing Model 787 Series Airplanes; Seats With Inflatable Lapbelts

Science.gov (United States)

2011-06-17

... to energy absorption throughout that range of occupants. In addition, the following situations must... invite interested people to take part in this rulemaking by sending written comments, data, or views. The...

Asset Condition, Information Systems and Decision Models

CERN Document Server

Willett, Roger; Brown, Kerry; Mathew, Joseph

2012-01-01

Asset Condition, Information Systems and Decision Models, is the second volume of the Engineering Asset Management Review Series. The manuscripts provide examples of implementations of asset information systems as well as some practical applications of condition data for diagnostics and prognostics. The increasing trend is towards prognostics rather than diagnostics, hence the need for assessment and decision models that promote the conversion of condition data into prognostic information to improve life-cycle planning for engineered assets. The research papers included here serve to support the on-going development of Condition Monitoring standards. This volume comprises selected papers from the 1st, 2nd, and 3rd World Congresses on Engineering Asset Management, which were convened under the auspices of ISEAM in collaboration with a number of organisations, including CIEAM Australia, Asset Management Council Australia, BINDT UK, and Chinese Academy of Sciences, Beijing University of Chemical Technology, Chin...

Weak diffusion limits of dynamic conditional correlation models

DEFF Research Database (Denmark)

Hafner, Christian M.; Laurent, Sebastien; Violante, Francesco

The properties of dynamic conditional correlation (DCC) models are still not entirely understood. This paper fills one of the gaps by deriving weak diffusion limits of a modified version of the classical DCC model. The limiting system of stochastic differential equations is characterized...... by a diffusion matrix of reduced rank. The degeneracy is due to perfect collinearity between the innovations of the volatility and correlation dynamics. For the special case of constant conditional correlations, a non-degenerate diffusion limit can be obtained. Alternative sets of conditions are considered...

The Accuracy of RADIANCE Software in Modelling Overcast Sky Condition

OpenAIRE

Baharuddin

2013-01-01

A validation study of the sky models of RADIANCE simulation software against the overcast sky condition has been carried out in order to test the accuracy of sky model of RADIANCE for modeling the overcast sky condition in Hong Kong. Two sets of data have been analysed. Firstly, data collected from a set of experiments using a physical scale model. In this experiment, the illuminance of four points inside the model was measured under real sky conditions. Secondly, the RADIANCE simulation has ...

Site environmental report for calendar year 2002. DOE operations at the Boeing Company, Rocketdyne Propulsion and Power

Energy Technology Data Exchange (ETDEWEB)

None

2003-09-30

This Annual Site Environmental Report (ASER) for 2002 describes the environmental conditions related to work performed for the Department of Energy (DOE) at Area IV of Boeing' s Santa Susana Field Laboratory (SSFL)). In the past, the Energy Technology Engineering Center (ETEC), a government-owned, company-operated test facility, was located in Area IV. The operations at ETEC included development, fabrication, and disassembly of nuclear reactors, reactor fuel, and other radioactive materials. Other activities at ETEC involved the operation of large-scale liquid metal facilities that were used for testing liquid metal fast breeder components. All nuclear work was terminated in 1988, and, subsequently, all radiological work has been directed toward decontamination and decommissioning (D&D) of the former nuclear facilities and their associated sites. Closure of the liquid metal test facilities began in 1996. Results of the radiological monitoring program for the calendar year 2002 continue to indicate that there are no significant releases of radioactive material from Area IV of SSFL. All potential exposure pathways are sampled and/or monitored, including air, soil, surface water, groundwater, direct radiation, transfer of property ( land, structures, waste), and recycling. All radioactive w astes are processed for disposal at DOE disposal sites and/or other licensed sites approved by DOE for radioactive waste disposal. No liquid radioactive wastes are released into the environment, and no structural debris from buildings w as transferred to municipal landfills or recycled in 2002.

A decision dependent stochastic process model for repairable systems with applications

Directory of Open Access Journals (Sweden)

Paul F. Zantek

2015-12-01

This paper mathematically formalizes the notion of how management actions impact the functioning of a repairable system over time by developing a new stochastic process model for such systems. The proposed model is illustrated using both simulated and real data. The proposed model compares favorably to other models for well-known data on Boeing airplanes. The model is further illustrated and compared to other models on failure time and maintenance data stemming from the South Texas Project nuclear power plant.

Fault condition stress analysis of NET 16 TF coil model

International Nuclear Information System (INIS)

Jong, C.T.J.

1992-04-01

As part of the design process of the NET/ITER toroidal field coils (TFCs), the mechanical behaviour of the magnetic system under fault conditions has to be analysed in some detail. Under fault conditions, either electrical or mechanical, the magnetic loading of the coils becomes extreme and further mechanical failure of parts of the overall structure might occur (e.g. failure of the coil, gravitational support, intercoil structure). The mechanical behaviour of the magnetic system under fault conditions has been analysed with a finite element model of the complete TFC system. The analysed fault conditions consist of: a thermal fault, electrical faults and mechanical faults. The mechanical faults have been applied simultaneously with an electrical fault. This report described the work carried out to create the finite element model of 16 TFCs and contains an extensive presentation of the results, obtained with this model, of a normal operating condition analysis and 9 fault condition analyses. Chapter 2-5 contains a detailed description of the finite element model, boundary conditions and loading conditions of the analyses made. Chapters 2-4 can be skipped if the reader is only interested in results. To understand the results presented chapter 6 is recommended, which contains a detailed description of all analysed fault conditions. The dimensions and geometry of the model correspond to the status of the NET/ITER TFC design of May 1990. Compared with previous models of the complete magnetic system, the finite element model of 16 TFCs is 'detailed', and can be used for linear elastic analysis with faulted loads. (author). 8 refs.; 204 figs.; 134 tabs

Standard Model Vacuum Stability and Weyl Consistency Conditions

DEFF Research Database (Denmark)

Antipin, Oleg; Gillioz, Marc; Krog, Jens

2013-01-01

At high energy the standard model possesses conformal symmetry at the classical level. This is reflected at the quantum level by relations between the different beta functions of the model. These relations are known as the Weyl consistency conditions. We show that it is possible to satisfy them...... order by order in perturbation theory, provided that a suitable coupling constant counting scheme is used. As a direct phenomenological application, we study the stability of the standard model vacuum at high energies and compare with previous computations violating the Weyl consistency conditions....

Modelling sulfamethoxazole degradation under different redox conditions

Science.gov (United States)

Sanchez-Vila, X.; Rodriguez-Escales, P.

2015-12-01

Sulfamethoxazole (SMX) is a low adsorptive, polar, sulfonamide antibiotic, widely present in aquatic environments. Degradation of SMX in subsurface porous media is spatially and temporally variable, depending on various environmental factors such as in situ redox potential, availability of nutrients, local soil characteristics, and temperature. It has been reported that SMX is better degraded under anoxic conditions and by co-metabolism processes. In this work, we first develop a conceptual model of degradation of SMX under different redox conditions (denitrification and iron reducing conditions), and second, we construct a mathematical model that allows reproducing different experiments of SMX degradation reported in the literature. The conceptual model focuses on the molecular behavior and contemplates the formation of different metabolites. The model was validated using the experimental data from Barbieri et al. (2012) and Mohatt et al. (2011). It adequately reproduces the reversible degradation of SMX under the presence of nitrite as an intermediate product of denitrification. In those experiments degradation was mediated by the transient formation of a diazonium cation, which was considered responsible of the substitution of the amine radical by a nitro radical, forming the 4-nitro-SMX. The formation of this metabolite is a reversible process, so that once the concentration of nitrite was back to zero due to further advancement of denitrification, the concentration of SMX was fully recovered. The forward reaction, formation of 4-nitro SMX, was modeled considering a kinetic of second order, whereas the backward reaction, dissociation of 4-nitro-SMX back to the original compound, could be modeled with a first order degradation reaction. Regarding the iron conditions, SMX was degraded due to the oxidation of iron (Fe2+), which was previously oxidized from goethite due to the degradation of a pool of labile organic carbon. As the oxidation of iron occurred on the

SUPPLY CHAIN FEATURES OF THE AEROSPACE INDUSTRY PARTICULAR CASE AIRBUS AND BOEING

Directory of Open Access Journals (Sweden)

Daniela MOCENCO

2015-10-01

Full Text Available Aerospace sector is one of the most globalized industries in terms of market structure and production system. Through aircraft development programs aviation industry has introduced new solutions to develop its products. The role of the partners involved in the development programs for the new generation aircraft is becoming increasingly important. Supply chain management has become a key factor for major manufacturers in the industry. The new strategies introduced by the aircraft manufacturers have increased the complexity of the supply process, design and production from the aviation industry. This paper highlights a series of factors regarding the aircraft programs supply chain management. In the first part are described the problems encountered by the manufacturers and airlines during the development of the most recent aircraft launched A350XWB and B787 Dreamliner; the second part focuses on the organizational structure of the supply chain, suppliers role within supply chain and also there are described the effects of the new strategies adopted by Airbus and Boeing in the aircraft development; the last part focuses on the risks and challenges that aviation industry is facing.

Sensitivity of a Simulated Derecho Event to Model Initial Conditions

Science.gov (United States)

Wang, Wei

2014-05-01

Since 2003, the MMM division at NCAR has been experimenting cloud-permitting scale weather forecasting using Weather Research and Forecasting (WRF) model. Over the years, we've tested different model physics, and tried different initial and boundary conditions. Not surprisingly, we found that the model's forecasts are more sensitive to the initial conditions than model physics. In 2012 real-time experiment, WRF-DART (Data Assimilation Research Testbed) at 15 km was employed to produce initial conditions for twice-a-day forecast at 3 km. On June 29, this forecast system captured one of the most destructive derecho event on record. In this presentation, we will examine forecast sensitivity to different model initial conditions, and try to understand the important features that may contribute to the success of the forecast.

Conditional shape models for cardiac motion estimation

DEFF Research Database (Denmark)

Metz, Coert; Baka, Nora; Kirisli, Hortense

2010-01-01

We propose a conditional statistical shape model to predict patient specific cardiac motion from the 3D end-diastolic CTA scan. The model is built from 4D CTA sequences by combining atlas based segmentation and 4D registration. Cardiac motion estimation is, for example, relevant in the dynamic...

Conditional dissipation of scalars in homogeneous turbulence: Closure for MMC modelling

Science.gov (United States)

Wandel, Andrew P.

2013-08-01

While the mean and unconditional variance are to be predicted well by any reasonable turbulent combustion model, these are generally not sufficient for the accurate modelling of complex phenomena such as extinction/reignition. An additional criterion has been recently introduced: accurate modelling of the dissipation timescales associated with fluctuations of scalars about their conditional mean (conditional dissipation timescales). Analysis of Direct Numerical Simulation (DNS) results for a passive scalar shows that the conditional dissipation timescale is of the order of the integral timescale and smaller than the unconditional dissipation timescale. A model is proposed: the conditional dissipation timescale is proportional to the integral timescale. This model is used in Multiple Mapping Conditioning (MMC) modelling for a passive scalar case and a reactive scalar case, comparing to DNS results for both. The results show that this model improves the accuracy of MMC predictions so as to match the DNS results more closely using a relatively-coarse spatial resolution compared to other turbulent combustion models.

VERIFICATION OF GEAR DYNAMIC MODEL IN DIFFERENT OPERATING CONDITIONS

Directory of Open Access Journals (Sweden)

Grzegorz PERUŃ

2014-09-01

Full Text Available The article presents the results of verification of the drive system dynamic model with gear. Tests were carried out on the real object in different operating conditions. For the same assumed conditions were also carried out simulation studies. Comparison of the results obtained from those two series of tests helped determine the suitability of the model and verify the possibility of replacing experimental research by simulations with use of dynamic model.

Modelling speech intelligibility in adverse conditions

DEFF Research Database (Denmark)

Jørgensen, Søren; Dau, Torsten

2013-01-01

Jørgensen and Dau (J Acoust Soc Am 130:1475-1487, 2011) proposed the speech-based envelope power spectrum model (sEPSM) in an attempt to overcome the limitations of the classical speech transmission index (STI) and speech intelligibility index (SII) in conditions with nonlinearly processed speech...... subjected to phase jitter, a condition in which the spectral structure of the intelligibility of speech signal is strongly affected, while the broadband temporal envelope is kept largely intact. In contrast, the effects of this distortion can be predicted -successfully by the spectro-temporal modulation...... suggest that the SNRenv might reflect a powerful decision metric, while some explicit across-frequency analysis seems crucial in some conditions. How such across-frequency analysis is "realized" in the auditory system remains unresolved....

FIDIC Conditions of Subcontract as a Model for General Conditions of Subcontract in Pakistan

Directory of Open Access Journals (Sweden)

Muhammad Umer Zubair

2016-12-01

Full Text Available Fair allocation of risks in conditions of contract is pivotal for coordination, unhindered execution, dispute resolution and maintenance of positive relationship among the parties executing the contract. Pakistani construction industry despite subcontracting a large percentage of construction projects lacks standard conditions of subcontract and they are primarily based on the will of the prime contractor that is onerous for the subcontractor. Therefore in order to develop a model for the general conditions of subcontract in Pakistan the conditions proposed by Associated General Contractors of California, FIDIC in 1994 and 2011, Construction Industry Development Board Malaysia, American Institute of Architects and by the Government of Hong Kong were compared to determine the similarities and differences among them. Afterwards a questionnaire based on the significant provisions of these subcontracts was conducted in the construction industry of Pakistan to determine the appropriate conditions for model subcontract. The results of the survey were further subjected to discussions with the legal experts. Out of 35 suggestions made for the general conditions of subcontract 23 originated from FIDIC in which 20 are recommended by its 2011’s version. It can therefore be implemented in Pakistan with certain amendments and additions as proposed in light of conditions of other subcontracts and the results of the survey and discussions with legal experts.

Status and test report on the LANL-Boeing APLE/HPO flying-wire beam-profile monitor. Status report

Energy Technology Data Exchange (ETDEWEB)

Wilke, M.; Barlow, D.; Fortgang, C.; Gilpatrick, J.; Meyer, R.; Rendon, A.; Warren, D. [Los Alamos National Lab., NM (United States); Greegor, R. [Boeing Co., Seattle, WA (United States)

1994-07-01

The High-Power Oscillator (HPO) demonstration of the Average Power Laser Experiment (APLE) is a collaboration by Los Alamos National Laboratory and Boeing to demonstrate a 10 kW average power, 10 {mu}m free electron laser (FEL). As part of the collaboration, Los Alamos National Laboratory (LANL) is responsible for many of the electron beam diagnostics in the linac, transport, and laser sections. Because of the high duty factor and power of the electron beam, special diagnostics are required. This report describes the flying wire diagnostic required to monitor the beam profile during high-power, high-duty operation. The authors describe the diagnostic and prototype tests on the Los Alamos APLE Prototype Experiment (APEX) FEL. They also describe the current status of the flying wires being built for APLE.

Modelling conditional heteroscedasticity in nonstationary series

NARCIS (Netherlands)

Cizek, P.; Cizek, P.; Härdle, W.K.; Weron, R.

2011-01-01

A vast amount of econometrical and statistical research deals with modeling financial time series and their volatility, which measures the dispersion of a series at a point in time (i.e., conditional variance). Although financial markets have been experiencing many shorter and longer periods of

Classically integrable boundary conditions for symmetric-space sigma models

International Nuclear Information System (INIS)

MacKay, N.J.; Young, C.A.S.

2004-01-01

We investigate boundary conditions for the non-linear sigma model on the compact symmetric space G/H. The Poisson brackets and the classical local conserved charges necessary for integrability are preserved by boundary conditions which correspond to involutions which commute with the involution defining H. Applied to SO(3)/SO(2), the non-linear sigma model on S 2 , these yield the great circles as boundary submanifolds. Applied to GxG/G, they reproduce known results for the principal chiral model

Adapting AIC to conditional model selection

NARCIS (Netherlands)

T. van Ommen (Thijs)

2012-01-01

textabstractIn statistical settings such as regression and time series, we can condition on observed information when predicting the data of interest. For example, a regression model explains the dependent variables $y_1, \\ldots, y_n$ in terms of the independent variables $x_1, \\ldots, x_n$.

Model checking conditional CSL for continuous-time Markov chains

DEFF Research Database (Denmark)

Gao, Yang; Xu, Ming; Zhan, Naijun

2013-01-01

In this paper, we consider the model-checking problem of continuous-time Markov chains (CTMCs) with respect to conditional logic. To the end, we extend Continuous Stochastic Logic introduced in Aziz et al. (2000) [1] to Conditional Continuous Stochastic Logic (CCSL) by introducing a conditional...

OPAL Netlogo Land Condition Model

Science.gov (United States)

2014-08-15

ER D C/ CE RL T R- 14 -1 2 Optimal Allocation of Land for Training and Non-training Uses ( OPAL ) OPAL Netlogo Land Condition Model...Fulton, Natalie Myers, Scott Tweddale, Dick Gebhart, Ryan Busby, Anne Dain-Owens, and Heidi Howard August 2014 OPAL team measuring above and...online library at http://acwc.sdp.sirsi.net/client/default. Optimal Allocation of Land for Training and Non-training Uses ( OPAL ) ERDC/CERL TR-14-12

76 FR 35336 - Airworthiness Directives; The Boeing Company Model 767 Airplanes

Science.gov (United States)

2011-06-17

... assembly rework 4 322 $662 48 $31,776. (required by AD 2001-14-19). Drain tube replacement (new Between 7.... configuration. We estimate the following costs to rework the drain tube assembly that might be required based on... might need this rework. On-Condition Costs Cost per Action Labor cost Parts cost product Drain tube...

Groundwater flow modelling under ice sheet conditions in Greenland (phase II)

International Nuclear Information System (INIS)

Jaquet, Olivier; Namar, Rabah; Siegel, Pascal; Jansson, Peter

2012-11-01

Within the framework of the GAP project, this second phase of geosphere modelling has enabled the development of an improved regional model that has led to a better representation of groundwater flow conditions likely to occur under ice sheet conditions. New data in relation to talik geometry and elevation, as well as to deformation zones were integrated in the geosphere model. In addition, more realistic hydraulic properties were considered for geosphere modelling; they were taken from the Laxemar site in Sweden. The geological medium with conductive deformation zones was modelled as a 3D continuum with stochastically hydraulic properties. Surface and basal glacial meltwater rates provided by a dynamic ice sheet model were assimilated into the groundwater flow model using mixed boundary conditions. The groundwater flow system is considered to be governed by infiltration of glacial meltwater in heterogeneous faulted crystalline rocks in the presence of permafrost and taliks. The characterisation of the permafrost-depth distribution was achieved using a coupled description of flow and heat transfer under steady state conditions. Using glaciological concepts and satellite data, an improved stochastic model was developed for the description at regional scale for the subglacial permafrost distribution in correlation with ice velocity and bed elevation data. Finally, the production of glacial meltwater by the ice sheet was traced for the determination of its depth and lateral extent. The major improvements are related to the type and handling of the subglacial boundary conditions. The use of meltwater rates provided by an ice sheet model applied as input to a mixed boundary condition enables to produce a more plausible flow field in the Eastern part of the domain, in comparison to previous modelling results (Jaquet et al. 2010). In addition, the integration of all potential taliks within the modelled domain provides a better characterisation of the likely groundwater

Groundwater flow modelling under ice sheet conditions in Greenland (phase II)

Energy Technology Data Exchange (ETDEWEB)

Jaquet, Olivier; Namar, Rabah; Siegel, Pascal [In2Earth Modelling Ltd, Lausanne (Switzerland); Jansson, Peter [Dept. of Physical Geography and Quaternary Geology, Stockholm Univ., Stockholm (Sweden)

2012-11-15

Within the framework of the GAP project, this second phase of geosphere modelling has enabled the development of an improved regional model that has led to a better representation of groundwater flow conditions likely to occur under ice sheet conditions. New data in relation to talik geometry and elevation, as well as to deformation zones were integrated in the geosphere model. In addition, more realistic hydraulic properties were considered for geosphere modelling; they were taken from the Laxemar site in Sweden. The geological medium with conductive deformation zones was modelled as a 3D continuum with stochastically hydraulic properties. Surface and basal glacial meltwater rates provided by a dynamic ice sheet model were assimilated into the groundwater flow model using mixed boundary conditions. The groundwater flow system is considered to be governed by infiltration of glacial meltwater in heterogeneous faulted crystalline rocks in the presence of permafrost and taliks. The characterisation of the permafrost-depth distribution was achieved using a coupled description of flow and heat transfer under steady state conditions. Using glaciological concepts and satellite data, an improved stochastic model was developed for the description at regional scale for the subglacial permafrost distribution in correlation with ice velocity and bed elevation data. Finally, the production of glacial meltwater by the ice sheet was traced for the determination of its depth and lateral extent. The major improvements are related to the type and handling of the subglacial boundary conditions. The use of meltwater rates provided by an ice sheet model applied as input to a mixed boundary condition enables to produce a more plausible flow field in the Eastern part of the domain, in comparison to previous modelling results (Jaquet et al. 2010). In addition, the integration of all potential taliks within the modelled domain provides a better characterisation of the likely groundwater

Modeling intelligent adversaries for terrorism risk assessment: some necessary conditions for adversary models.

Science.gov (United States)

Guikema, Seth

2012-07-01

Intelligent adversary modeling has become increasingly important for risk analysis, and a number of different approaches have been proposed for incorporating intelligent adversaries in risk analysis models. However, these approaches are based on a range of often-implicit assumptions about the desirable properties of intelligent adversary models. This "Perspective" paper aims to further risk analysis for situations involving intelligent adversaries by fostering a discussion of the desirable properties for these models. A set of four basic necessary conditions for intelligent adversary models is proposed and discussed. These are: (1) behavioral accuracy to the degree possible, (2) computational tractability to support decision making, (3) explicit consideration of uncertainty, and (4) ability to gain confidence in the model. It is hoped that these suggested necessary conditions foster discussion about the goals and assumptions underlying intelligent adversary modeling in risk analysis. © 2011 Society for Risk Analysis.

75 FR 81 - Special Conditions: Boeing Model 787-8 Airplane; Overhead Flightcrew Rest Compartment Occupiable...

Science.gov (United States)

2010-01-04

... and protective breathing equipment (PBE). This analysis should consider the possibility of fire in any..., mechanical or structural failure, or persons standing below or against the crew rest compartment outlets. One..., volume of the compartment, and the ventilation rate. The system must have sufficient extinguishing agent...

76 FR 10482 - Special Conditions: Boeing Model 787-8 Airplane; Overhead Flightcrew-Rest Compartment Occupiable...

Science.gov (United States)

2011-02-25

... out. (b) For a manual, hand-held extinguishing system (designed as the sole means to fight a fire or..., except that Sec. 25.1309 remains at Amendment 25- 117 for cargo-fire protection systems. If the... to two flight crewmembers trained in the evacuation, fire fighting, and depressurization procedures...

Testing and modelling autoregressive conditional heteroskedasticity of streamflow processes

Directory of Open Access Journals (Sweden)

W. Wang

2005-01-01

Full Text Available Conventional streamflow models operate under the assumption of constant variance or season-dependent variances (e.g. ARMA (AutoRegressive Moving Average models for deseasonalized streamflow series and PARMA (Periodic AutoRegressive Moving Average models for seasonal streamflow series. However, with McLeod-Li test and Engle's Lagrange Multiplier test, clear evidences are found for the existence of autoregressive conditional heteroskedasticity (i.e. the ARCH (AutoRegressive Conditional Heteroskedasticity effect, a nonlinear phenomenon of the variance behaviour, in the residual series from linear models fitted to daily and monthly streamflow processes of the upper Yellow River, China. It is shown that the major cause of the ARCH effect is the seasonal variation in variance of the residual series. However, while the seasonal variation in variance can fully explain the ARCH effect for monthly streamflow, it is only a partial explanation for daily flow. It is also shown that while the periodic autoregressive moving average model is adequate in modelling monthly flows, no model is adequate in modelling daily streamflow processes because none of the conventional time series models takes the seasonal variation in variance, as well as the ARCH effect in the residuals, into account. Therefore, an ARMA-GARCH (Generalized AutoRegressive Conditional Heteroskedasticity error model is proposed to capture the ARCH effect present in daily streamflow series, as well as to preserve seasonal variation in variance in the residuals. The ARMA-GARCH error model combines an ARMA model for modelling the mean behaviour and a GARCH model for modelling the variance behaviour of the residuals from the ARMA model. Since the GARCH model is not followed widely in statistical hydrology, the work can be a useful addition in terms of statistical modelling of daily streamflow processes for the hydrological community.

Modeling air concentration over macro roughness conditions by Artificial Intelligence techniques

Science.gov (United States)

Roshni, T.; Pagliara, S.

2018-05-01

Aeration is improved in rivers by the turbulence created in the flow over macro and intermediate roughness conditions. Macro and intermediate roughness flow conditions are generated by flows over block ramps or rock chutes. The measurements are taken in uniform flow region. Efficacy of soft computing methods in modeling hydraulic parameters are not common so far. In this study, modeling efficiencies of MPMR model and FFNN model are found for estimating the air concentration over block ramps under macro roughness conditions. The experimental data are used for training and testing phases. Potential capability of MPMR and FFNN model in estimating air concentration are proved through this study.

Modelling the Thermomechanical Conditions in Friction Stir Welding

DEFF Research Database (Denmark)

Schmidt, Henrik Nikolaj Blich

Friction Stir Welding is a solid-state welding process invented by TWI in 1991. The FSW process is unique in the sense that joining of un-weldable alloys readily can be made. The thermomechanical conditions present in the workpiece during the welding process are of great interest since...... these control the properties of the weld. In the present work, a set of experimental, analytical and numerical analyses are carried out in order to evaluate the thermomechanical conditions descriptive for welding of aluminium, in this case AA2024-T3, under a specific set of welding parameters. Despite...... these specific data, the developed models can be applied for other alloys and welding parameters as well. A detailed experiment is carried out which constitutes the basis for the development and validation of the numerical and analytical models presented in this work. The contact condition at the tool...

Fitting and Testing Conditional Multinormal Partial Credit Models

Science.gov (United States)

Hessen, David J.

2012-01-01

A multinormal partial credit model for factor analysis of polytomously scored items with ordered response categories is derived using an extension of the Dutch Identity (Holland in "Psychometrika" 55:5-18, 1990). In the model, latent variables are assumed to have a multivariate normal distribution conditional on unweighted sums of item…

On the Conditioning of Machine-Learning-Assisted Turbulence Modeling

Science.gov (United States)

Wu, Jinlong; Sun, Rui; Wang, Qiqi; Xiao, Heng

2017-11-01

Recently, several researchers have demonstrated that machine learning techniques can be used to improve the RANS modeled Reynolds stress by training on available database of high fidelity simulations. However, obtaining improved mean velocity field remains an unsolved challenge, restricting the predictive capability of current machine-learning-assisted turbulence modeling approaches. In this work we define a condition number to evaluate the model conditioning of data-driven turbulence modeling approaches, and propose a stability-oriented machine learning framework to model Reynolds stress. Two canonical flows, the flow in a square duct and the flow over periodic hills, are investigated to demonstrate the predictive capability of the proposed framework. The satisfactory prediction performance of mean velocity field for both flows demonstrates the predictive capability of the proposed framework for machine-learning-assisted turbulence modeling. With showing the capability of improving the prediction of mean flow field, the proposed stability-oriented machine learning framework bridges the gap between the existing machine-learning-assisted turbulence modeling approaches and the demand of predictive capability of turbulence models in real applications.

On specification of initial conditions in turbulence models

Energy Technology Data Exchange (ETDEWEB)

Rollin, Bertrand [Los Alamos National Laboratory; Andrews, Malcolm J [Los Alamos National Laboratory

2010-12-01

Recent research has shown that initial conditions have a significant influence on the evolution of a flow towards turbulence. This important finding offers a unique opportunity for turbulence control, but also raises the question of how to properly specify initial conditions in turbulence models. We study this problem in the context of the Rayleigh-Taylor instability. The Rayleigh-Taylor instability is an interfacial fluid instability that leads to turbulence and turbulent mixing. It occurs when a light fluid is accelerated in to a heavy fluid because of misalignment between density and pressure gradients. The Rayleigh-Taylor instability plays a key role in a wide variety of natural and man-made flows ranging from supernovae to the implosion phase of Inertial Confinement Fusion (ICF). Our approach consists of providing the turbulence models with a predicted profile of its key variables at the appropriate time in accordance to the initial conditions of the problem.

Verification of the karst flow model under laboratory controlled conditions

Science.gov (United States)

Gotovac, Hrvoje; Andric, Ivo; Malenica, Luka; Srzic, Veljko

2016-04-01

Karst aquifers are very important groundwater resources around the world as well as in coastal part of Croatia. They consist of extremely complex structure defining by slow and laminar porous medium and small fissures and usually fast turbulent conduits/karst channels. Except simple lumped hydrological models that ignore high karst heterogeneity, full hydraulic (distributive) models have been developed exclusively by conventional finite element and finite volume elements considering complete karst heterogeneity structure that improves our understanding of complex processes in karst. Groundwater flow modeling in complex karst aquifers are faced by many difficulties such as a lack of heterogeneity knowledge (especially conduits), resolution of different spatial/temporal scales, connectivity between matrix and conduits, setting of appropriate boundary conditions and many others. Particular problem of karst flow modeling is verification of distributive models under real aquifer conditions due to lack of above-mentioned information. Therefore, we will show here possibility to verify karst flow models under the laboratory controlled conditions. Special 3-D karst flow model (5.6*2.6*2 m) consists of concrete construction, rainfall platform, 74 piezometers, 2 reservoirs and other supply equipment. Model is filled by fine sand (3-D porous matrix) and drainage plastic pipes (1-D conduits). This model enables knowledge of full heterogeneity structure including position of different sand layers as well as conduits location and geometry. Moreover, we know geometry of conduits perforation that enable analysis of interaction between matrix and conduits. In addition, pressure and precipitation distribution and discharge flow rates from both phases can be measured very accurately. These possibilities are not present in real sites what this model makes much more useful for karst flow modeling. Many experiments were performed under different controlled conditions such as different

MENENTUKAN PORTOFOLIO OPTIMAL MENGGUNAKAN MODEL CONDITIONAL MEAN VARIANCE

Directory of Open Access Journals (Sweden)

I GEDE ERY NISCAHYANA

2016-08-01

Full Text Available When the returns of stock prices show the existence of autocorrelation and heteroscedasticity, then conditional mean variance models are suitable method to model the behavior of the stocks. In this thesis, the implementation of the conditional mean variance model to the autocorrelated and heteroscedastic return was discussed. The aim of this thesis was to assess the effect of the autocorrelated and heteroscedastic returns to the optimal solution of a portfolio. The margin of four stocks, Fortune Mate Indonesia Tbk (FMII.JK, Bank Permata Tbk (BNLI.JK, Suryamas Dutamakmur Tbk (SMDM.JK dan Semen Gresik Indonesia Tbk (SMGR.JK were estimated by GARCH(1,1 model with standard innovations following the standard normal distribution and the t-distribution.  The estimations were used to construct a portfolio. The portfolio optimal was found when the standard innovation used was t-distribution with the standard deviation of 1.4532 and the mean of 0.8023 consisting of 0.9429 (94% of FMII stock, 0.0473 (5% of  BNLI stock, 0% of SMDM stock, 1% of  SMGR stock.

Modelling and Control of Ionic Electroactive Polymer Actuators under Varying Humidity Conditions

Directory of Open Access Journals (Sweden)

S. Sunjai Nakshatharan

2018-02-01

Full Text Available In this work, we address the problem of position control of ionic electroactive polymer soft actuators under varying relative humidity conditions. The impact of humidity on the actuation performance of ionic actuators is studied through frequency response and impedance spectroscopy analysis. Considering the uncertain performance of the actuator under varying humidity conditions, an adaptable model using the neural network method is developed. The model uses relative humidity magnitude as one of the model parameters, making it robust to different environmental conditions. Utilizing the model, a closed-loop controller based on the model predictive controller is developed for position control of the actuator. The developed model and controller are experimentally verified and found to be capable of predicting and controlling the actuators with excellent tracking accuracy under relative humidity conditions varying in the range of 10–90%.

Groundwater flow modelling under ice sheet conditions. Scoping calculations

International Nuclear Information System (INIS)

Jaquet, O.; Namar, R.; Jansson, P.

2010-10-01

The potential impact of long-term climate changes has to be evaluated with respect to repository performance and safety. In particular, glacial periods of advancing and retreating ice sheet and prolonged permafrost conditions are likely to occur over the repository site. The growth and decay of ice sheets and the associated distribution of permafrost will affect the groundwater flow field and its composition. As large changes may take place, the understanding of groundwater flow patterns in connection to glaciations is an important issue for the geological disposal at long term. During a glacial period, the performance of the repository could be weakened by some of the following conditions and associated processes: - Maximum pressure at repository depth (canister failure). - Maximum permafrost depth (canister failure, buffer function). - Concentration of groundwater oxygen (canister corrosion). - Groundwater salinity (buffer stability). - Glacially induced earthquakes (canister failure). Therefore, the GAP project aims at understanding key hydrogeological issues as well as answering specific questions: - Regional groundwater flow system under ice sheet conditions. - Flow and infiltration conditions at the ice sheet bed. - Penetration depth of glacial meltwater into the bedrock. - Water chemical composition at repository depth in presence of glacial effects. - Role of the taliks, located in front of the ice sheet, likely to act as potential discharge zones of deep groundwater flow. - Influence of permafrost distribution on the groundwater flow system in relation to build-up and thawing periods. - Consequences of glacially induced earthquakes on the groundwater flow system. Some answers will be provided by the field data and investigations; the integration of the information and the dynamic characterisation of the key processes will be obtained using numerical modelling. Since most of the data are not yet available, some scoping calculations are performed using the

Groundwater flow modelling under ice sheet conditions. Scoping calculations

Energy Technology Data Exchange (ETDEWEB)

Jaquet, O.; Namar, R. (In2Earth Modelling Ltd (Switzerland)); Jansson, P. (Dept. of Physical Geography and Quaternary Geology, Stockholm Univ., Stockholm (Sweden))

2010-10-15

The potential impact of long-term climate changes has to be evaluated with respect to repository performance and safety. In particular, glacial periods of advancing and retreating ice sheet and prolonged permafrost conditions are likely to occur over the repository site. The growth and decay of ice sheets and the associated distribution of permafrost will affect the groundwater flow field and its composition. As large changes may take place, the understanding of groundwater flow patterns in connection to glaciations is an important issue for the geological disposal at long term. During a glacial period, the performance of the repository could be weakened by some of the following conditions and associated processes: - Maximum pressure at repository depth (canister failure). - Maximum permafrost depth (canister failure, buffer function). - Concentration of groundwater oxygen (canister corrosion). - Groundwater salinity (buffer stability). - Glacially induced earthquakes (canister failure). Therefore, the GAP project aims at understanding key hydrogeological issues as well as answering specific questions: - Regional groundwater flow system under ice sheet conditions. - Flow and infiltration conditions at the ice sheet bed. - Penetration depth of glacial meltwater into the bedrock. - Water chemical composition at repository depth in presence of glacial effects. - Role of the taliks, located in front of the ice sheet, likely to act as potential discharge zones of deep groundwater flow. - Influence of permafrost distribution on the groundwater flow system in relation to build-up and thawing periods. - Consequences of glacially induced earthquakes on the groundwater flow system. Some answers will be provided by the field data and investigations; the integration of the information and the dynamic characterisation of the key processes will be obtained using numerical modelling. Since most of the data are not yet available, some scoping calculations are performed using the

A new model for friction under shock conditions

Directory of Open Access Journals (Sweden)

Dambakizi F.

2011-01-01

Full Text Available This article is aimed at the developpement of a new model for friction under shock conditions. Thanks to a subgrid model and a specific Coulomb friction law, it takes into account the interface temperature and deformation but also the influence of asperities when the contact pressure is relatively low (≤ 3 GPa.

Model development for air conditioning system in heavy duty trucks

NARCIS (Netherlands)

Kessels, J.T.B.A.; van den Bosch, P.P.J.; Zhang, Quansheng; Li, Shengbo Eben; Deng, Kun

2016-01-01

This chapter presents a modelling approach for the air conditioning (AC) system in heavy duty trucks. The presented model entails two major elements: a mechanical compressor model and a thermal AC model. The compressor model describes the massflow of the refrigerant as well as the mechanical power

A model to predict moisture conditions in concrete reactor containments

International Nuclear Information System (INIS)

Ahs, M.; Nilsson, L.O.; Poyet, S.; L'Hostis, V.

2015-01-01

Moisture has an impact in many of the degradation mechanisms that appear in the structures of a nuclear power plant. Moisture conditions in a reactor containment wall have been simulated by using a hygro-thermal model of drying concrete. Methods to estimate the temperature dependency of the sorption isotherms and moisture transport properties is suggested and applied in the model. This temperature dependency is included as there is a temperature gradient present through the containment wall. The hygro-thermal model was applied on a full scale 3D model of a real reactor containment building and the concrete relative humidity has been computed at 4 different moments: 1, 10, 20 and 30 years. The results show that the major part of the concrete is not dried at all even after 30 years of operation. It is also clear that the temperature distribution inside the whole concrete volume is affected by the variable boundary conditions. It was concluded that the suggested hygro-thermal model was appropriate to use as a method to estimate the existing conditions in a PWR reactor containment wall

Cosmological viability conditions for f(T) dark energy models

Energy Technology Data Exchange (ETDEWEB)

Setare, M.R.; Mohammadipour, N., E-mail: rezakord@ipm.ir, E-mail: N.Mohammadipour@uok.ac.ir [Department of Science, University of Kurdistan, Sanandaj (Iran, Islamic Republic of)

2012-11-01

Recently f(T) modified teleparallel gravity where T is the torsion scalar has been proposed as the natural gravitational alternative for dark energy. We perform a detailed dynamical analysis of these models and find conditions for the cosmological viability of f(T) dark energy models as geometrical constraints on the derivatives of these models. We show that in the phase space exists two cosmologically viable trajectory which (i) The universe would start from an unstable radiation point, then pass a saddle standard matter point which is followed by accelerated expansion de sitter point. (ii) The universe starts from a saddle radiation epoch, then falls onto the stable matter era and the system can not evolve to the dark energy dominated epoch. Finally, for a number of f(T) dark energy models were proposed in the more literature, the viability conditions are investigated.

Nested Bethe Ansatz for Spin Ladder Model with Open Boundary Conditions

International Nuclear Information System (INIS)

Wu Junfang; Zhang Chunmin; Yue Ruihong; Li Runling

2005-01-01

The nested Bethe ansatz (BA) method is applied to find the eigenvalues and the eigenvectors of the transfer matrix for spin-ladder model with open boundary conditions. Based on the reflection equation, we find the general diagonal solution, which determines the general boundary interaction in the Hamiltonian. We introduce the spin-ladder model with open boundary conditions. By finding the solution K ± of the reflection equation which determines the nontrivial boundary terms in the Hamiltonian, we diagonalize the transfer matrix of the spin-ladder model with open boundary conditions in the framework of nested BA.

APPLICABILITY OF SIMILARITY CONDITIONS TO ANALOGUE MODELLING OF TECTONIC STRUCTURES

Directory of Open Access Journals (Sweden)

Mikhail A. Goncharov

2010-01-01

Full Text Available The publication is aimed at comparing concepts of V.V. Belousov and M.V. Gzovsky, outstanding researchers who established fundamentals of tectonophysics in Russia, specifically similarity conditions in application to tectonophysical modeling. Quotations from their publications illustrate differences in their views. In this respect, we can reckon V.V. Belousov as a «realist» as he supported «the liberal point of view» [Methods of modelling…, 1988, p. 21–22], whereas M.V. Gzovsky can be regarded as an «idealist» as he believed that similarity conditions should be mandatorily applied to ensure correctness of physical modeling of tectonic deformations and structures [Gzovsky, 1975, pp. 88 and 94].Objectives of the present publication are (1 to be another reminder about desirability of compliance with similarity conditions in experimental tectonics; (2 to point out difficulties in ensuring such compliance; (3 to give examples which bring out the fact that similarity conditions are often met per se, i.e. automatically observed; (4 to show that modeling can be simplified in some cases without compromising quantitative estimations of parameters of structure formation.(1 Physical modelling of tectonic deformations and structures should be conducted, if possible, in compliance with conditions of geometric and physical similarity between experimental models and corresponding natural objects. In any case, a researcher should have a clear vision of conditions applicable to each particular experiment.(2 Application of similarity conditions is often challenging due to unavoidable difficulties caused by the following: a Imperfection of experimental equipment and technologies (Fig. 1 to 3; b uncertainties in estimating parameters of formation of natural structures, including main ones: structure size (Fig. 4, time of formation (Fig. 5, deformation properties of the medium wherein such structures are formed, including, first of all, viscosity (Fig. 6

'Duality twisted'boundary conditions in n-state Potts Models

International Nuclear Information System (INIS)

Schuetz, G.

1992-11-01

We discuss a new class of toroidal boundary conditions for one-dimensional quantum Hamiltonian with S n symmetry which are related to two-dimensional n-state Potts models in the extreme anisotropic Hamiltonian limit. At their self-dual point (a point were a second-order phase transition occurs for n=2,3,4) the duality transformation is shown to be an additional symmetry giving rise to a new class of 'duality twisted' toroidal boundary conditions. This corresponding Hamiltonians are given in terms of generators of the periodic Temprely-Lieb algebra with an odd number of generators. We discuss as an example the critical Ising model. Here the complete spectrum for the new boundary conditions can be obtained from a projection mechanism in the spin-1/2 XXZ Heisenberg chain. (author)

78 FR 28128 - Airworthiness Directives; the Boeing Company Airplanes

Science.gov (United States)

2013-05-14

...) of America Code 2800, Aircraft Fuel System. (e) Unsafe Condition This AD was prompted by reports of... occurrences on Model 737-400 airplanes of total loss of boost pump pressure of the fuel feed system, followed by loss of fuel system suction feed capability on one engine, and in-flight shutdown of the engine...

Advanced Modeling and Uncertainty Quantification for Flight Dynamics; Interim Results and Challenges

Science.gov (United States)

Hyde, David C.; Shweyk, Kamal M.; Brown, Frank; Shah, Gautam

2014-01-01

As part of the NASA Vehicle Systems Safety Technologies (VSST), Assuring Safe and Effective Aircraft Control Under Hazardous Conditions (Technical Challenge #3), an effort is underway within Boeing Research and Technology (BR&T) to address Advanced Modeling and Uncertainty Quantification for Flight Dynamics (VSST1-7). The scope of the effort is to develop and evaluate advanced multidisciplinary flight dynamics modeling techniques, including integrated uncertainties, to facilitate higher fidelity response characterization of current and future aircraft configurations approaching and during loss-of-control conditions. This approach is to incorporate multiple flight dynamics modeling methods for aerodynamics, structures, and propulsion, including experimental, computational, and analytical. Also to be included are techniques for data integration and uncertainty characterization and quantification. This research shall introduce new and updated multidisciplinary modeling and simulation technologies designed to improve the ability to characterize airplane response in off-nominal flight conditions. The research shall also introduce new techniques for uncertainty modeling that will provide a unified database model comprised of multiple sources, as well as an uncertainty bounds database for each data source such that a full vehicle uncertainty analysis is possible even when approaching or beyond Loss of Control boundaries. Methodologies developed as part of this research shall be instrumental in predicting and mitigating loss of control precursors and events directly linked to causal and contributing factors, such as stall, failures, damage, or icing. The tasks will include utilizing the BR&T Water Tunnel to collect static and dynamic data to be compared to the GTM extended WT database, characterizing flight dynamics in off-nominal conditions, developing tools for structural load estimation under dynamic conditions, devising methods for integrating various modeling elements

Modelling the meteorological forest fire niche in heterogeneous pyrologic conditions.

Science.gov (United States)

De Angelis, Antonella; Ricotta, Carlo; Conedera, Marco; Pezzatti, Gianni Boris

2015-01-01

Fire regimes are strongly related to weather conditions that directly and indirectly influence fire ignition and propagation. Identifying the most important meteorological fire drivers is thus fundamental for daily fire risk forecasting. In this context, several fire weather indices have been developed focussing mainly on fire-related local weather conditions and fuel characteristics. The specificity of the conditions for which fire danger indices are developed makes its direct transfer and applicability problematic in different areas or with other fuel types. In this paper we used the low-to-intermediate fire-prone region of Canton Ticino as a case study to develop a new daily fire danger index by implementing a niche modelling approach (Maxent). In order to identify the most suitable weather conditions for fires, different combinations of input variables were tested (meteorological variables, existing fire danger indices or a combination of both). Our findings demonstrate that such combinations of input variables increase the predictive power of the resulting index and surprisingly even using meteorological variables only allows similar or better performances than using the complex Canadian Fire Weather Index (FWI). Furthermore, the niche modelling approach based on Maxent resulted in slightly improved model performance and in a reduced number of selected variables with respect to the classical logistic approach. Factors influencing final model robustness were the number of fire events considered and the specificity of the meteorological conditions leading to fire ignition.

Response moderation models for conditional dependence between response time and response accuracy.

Science.gov (United States)

Bolsinova, Maria; Tijmstra, Jesper; Molenaar, Dylan

2017-05-01

It is becoming more feasible and common to register response times in the application of psychometric tests. Researchers thus have the opportunity to jointly model response accuracy and response time, which provides users with more relevant information. The most common choice is to use the hierarchical model (van der Linden, 2007, Psychometrika, 72, 287), which assumes conditional independence between response time and accuracy, given a person's speed and ability. However, this assumption may be violated in practice if, for example, persons vary their speed or differ in their response strategies, leading to conditional dependence between response time and accuracy and confounding measurement. We propose six nested hierarchical models for response time and accuracy that allow for conditional dependence, and discuss their relationship to existing models. Unlike existing approaches, the proposed hierarchical models allow for various forms of conditional dependence in the model and allow the effect of continuous residual response time on response accuracy to be item-specific, person-specific, or both. Estimation procedures for the models are proposed, as well as two information criteria that can be used for model selection. Parameter recovery and usefulness of the information criteria are investigated using simulation, indicating that the procedure works well and is likely to select the appropriate model. Two empirical applications are discussed to illustrate the different types of conditional dependence that may occur in practice and how these can be captured using the proposed hierarchical models. © 2016 The British Psychological Society.

Conditioning 3D object-based models to dense well data

Science.gov (United States)

Wang, Yimin C.; Pyrcz, Michael J.; Catuneanu, Octavian; Boisvert, Jeff B.

2018-06-01

Object-based stochastic simulation models are used to generate categorical variable models with a realistic representation of complicated reservoir heterogeneity. A limitation of object-based modeling is the difficulty of conditioning to dense data. One method to achieve data conditioning is to apply optimization techniques. Optimization algorithms can utilize an objective function measuring the conditioning level of each object while also considering the geological realism of the object. Here, an objective function is optimized with implicit filtering which considers constraints on object parameters. Thousands of objects conditioned to data are generated and stored in a database. A set of objects are selected with linear integer programming to generate the final realization and honor all well data, proportions and other desirable geological features. Although any parameterizable object can be considered, objects from fluvial reservoirs are used to illustrate the ability to simultaneously condition multiple types of geologic features. Channels, levees, crevasse splays and oxbow lakes are parameterized based on location, path, orientation and profile shapes. Functions mimicking natural river sinuosity are used for the centerline model. Channel stacking pattern constraints are also included to enhance the geological realism of object interactions. Spatial layout correlations between different types of objects are modeled. Three case studies demonstrate the flexibility of the proposed optimization-simulation method. These examples include multiple channels with high sinuosity, as well as fragmented channels affected by limited preservation. In all cases the proposed method reproduces input parameters for the object geometries and matches the dense well constraints. The proposed methodology expands the applicability of object-based simulation to complex and heterogeneous geological environments with dense sampling.

Modelling conditional correlations of asset returns: A smooth transition approach

DEFF Research Database (Denmark)

Silvennoinen, Annastiina; Teräsvirta, Timo

In this paper we propose a new multivariate GARCH model with time-varying conditional correlation structure. The time-varying conditional correlations change smoothly between two extreme states of constant correlations according to a predetermined or exogenous transition variable. An LM-test is d......In this paper we propose a new multivariate GARCH model with time-varying conditional correlation structure. The time-varying conditional correlations change smoothly between two extreme states of constant correlations according to a predetermined or exogenous transition variable. An LM......-test is derived to test the constancy of correlations and LM- and Wald tests to test the hypothesis of partially constant correlations. Analytical expressions for the test statistics and the required derivatives are provided to make computations feasible. An empirical example based on daily return series of ve...

Modeling the Conditional Covariance between Stock and Bond Returns

NARCIS (Netherlands)

P. de Goeij (Peter); W.A. Marquering (Wessel)

2002-01-01

textabstractTo analyze the intertemporal interaction between the stock and bond market returns, we allow the conditional covariance matrix to vary over time according to a multivariate GARCH model similar to Bollerslev, Engle and Wooldridge (1988). We extend the model such that it allows for

URGAP: A gap conductance model for transient conditions

International Nuclear Information System (INIS)

Lassmann, K.; Pazdera, F.

1983-01-01

A gap conductance model, URGAP, has been developed with contributions from solid, fluid and radiation heat transfer components. Model parameters are easily available, independent of different combinations of material surfaces. The model parameters were fitted to 388 data points under reactor conditions. For model verification, another 274 data points of steel-steel and aluminium-aluminium interfaces, respectively, were used. For minor surface roughnesses normally prevailing in reactor fuel elements the model asymptotically yields Ross' and Stoute's model for the open gap, which is thus confirmed. Materials data were carefully checked over a wide range of temperatures. Special attention was paid to the contact term for high temperatures. Thus, the model can be applied to transients. The URGAP model is being used successfully in several codes (e.g. URANUS, SSYST). (author)

Modelling Conditional and Unconditional Heteroskedasticity with Smoothly Time-Varying Structure

DEFF Research Database (Denmark)

Amado, Christina; Teräsvirta, Timo

multiplier type misspecification tests. Finite-sample properties of these procedures and tests are examined by simulation. An empirical application to daily stock returns and another one to daily exchange rate returns illustrate the functioning and properties of our modelling strategy in practice......In this paper, we propose two parametric alternatives to the standard GARCH model. They allow the conditional variance to have a smooth time-varying structure of either ad- ditive or multiplicative type. The suggested parameterizations describe both nonlinearity and structural change...... in the conditional and unconditional variances where the transition between regimes over time is smooth. A modelling strategy for these new time-varying parameter GARCH models is developed. It relies on a sequence of Lagrange multiplier tests, and the adequacy of the estimated models is investigated by Lagrange...

Radionuclide Transport Models Under Ambient Conditions

International Nuclear Information System (INIS)

Moridis, G.; Hu, Q.

2000-01-01

The purpose of this Analysis/Model Report (AMR) is to evaluate (by means of 2-D semianalytical and 3-D numerical models) the transport of radioactive solutes and colloids in the unsaturated zone (UZ) under ambient conditions from the potential repository horizon to the water table at Yucca Mountain (YM), Nevada. This is in accordance with the ''AMR Development Plan U0060, Radionuclide Transport Models Under Ambient Conditions'' (CRWMS M and O 1999a). This AMR supports the UZ Flow and Transport Process Model Report (PMR). This AMR documents the UZ Radionuclide Transport Model (RTM). This model considers: the transport of radionuclides through fractured tuffs; the effects of changes in the intensity and configuration of fracturing from hydrogeologic unit to unit; colloid transport; physical and retardation processes and the effects of perched water. In this AMR they document the capabilities of the UZ RTM, which can describe flow (saturated and/or unsaturated) and transport, and accounts for (a) advection, (b) molecular diffusion, (c) hydrodynamic dispersion (with full 3-D tensorial representation), (d) kinetic or equilibrium physical and/or chemical sorption (linear, Langmuir, Freundlich or combined), (e) first-order linear chemical reaction, (f) radioactive decay and tracking of daughters, (g) colloid filtration (equilibrium, kinetic or combined), and (h) colloid-assisted solute transport. Simulations of transport of radioactive solutes and colloids (incorporating the processes described above) from the repository horizon to the water table are performed to support model development and support studies for Performance Assessment (PA). The input files for these simulations include transport parameters obtained from other AMRs (i.e., CRWMS M and O 1999d, e, f, g, h; 2000a, b, c, d). When not available, the parameter values used are obtained from the literature. The results of the simulations are used to evaluate the transport of radioactive solutes and colloids, and

A Multivariate Asymmetric Long Memory Conditional Volatility Model with X, Regularity and Asymptotics

NARCIS (Netherlands)

M. Asai (Manabu); M.J. McAleer (Michael)

2016-01-01

textabstractThe paper derives a Multivariate Asymmetric Long Memory conditional volatility model with Exogenous Variables (X), or the MALMX model, with dynamic conditional correlations, appropriate regularity conditions, and associated asymptotic theory. This enables checking of internal consistency

Predicting birth weight with conditionally linear transformation models.

Science.gov (United States)

Möst, Lisa; Schmid, Matthias; Faschingbauer, Florian; Hothorn, Torsten

2016-12-01

Low and high birth weight (BW) are important risk factors for neonatal morbidity and mortality. Gynecologists must therefore accurately predict BW before delivery. Most prediction formulas for BW are based on prenatal ultrasound measurements carried out within one week prior to birth. Although successfully used in clinical practice, these formulas focus on point predictions of BW but do not systematically quantify uncertainty of the predictions, i.e. they result in estimates of the conditional mean of BW but do not deliver prediction intervals. To overcome this problem, we introduce conditionally linear transformation models (CLTMs) to predict BW. Instead of focusing only on the conditional mean, CLTMs model the whole conditional distribution function of BW given prenatal ultrasound parameters. Consequently, the CLTM approach delivers both point predictions of BW and fetus-specific prediction intervals. Prediction intervals constitute an easy-to-interpret measure of prediction accuracy and allow identification of fetuses subject to high prediction uncertainty. Using a data set of 8712 deliveries at the Perinatal Centre at the University Clinic Erlangen (Germany), we analyzed variants of CLTMs and compared them to standard linear regression estimation techniques used in the past and to quantile regression approaches. The best-performing CLTM variant was competitive with quantile regression and linear regression approaches in terms of conditional coverage and average length of the prediction intervals. We propose that CLTMs be used because they are able to account for possible heteroscedasticity, kurtosis, and skewness of the distribution of BWs. © The Author(s) 2014.

76 FR 5061 - Special Conditions: TTF Aerospace, LLC, Modification to Boeing Model 767-300 Series Airplanes...

Science.gov (United States)

2011-01-28

..., at least one means must be provided to cover anticipated turbulence (e.g., sufficient handholds... without an intervening cargo compartment wall, the following applies: (a) Any wall of the module...

76 FR 17334 - Special Conditions: Boeing Model 747-2G4B Airplane; Certification of Cooktops

Science.gov (United States)

2011-03-29

... into the passenger cabin environment. These potential hazards to the airplane and its occupants must be... airplane and its occupants from these potential hazards. Accordingly, this system is considered to be a novel or unusual design feature. Discussion Currently, ovens are the prevailing means of heating food on...

77 FR 67251 - Special Conditions: Boeing Model 757 Series Airplanes; Seats with Non-Traditional, Large, Non...

Science.gov (United States)

2012-11-09

... metal, the contribution to a fire in the cabin had been minimized and was not considered a threat. For...-metallic panels that would affect survivability during a post-crash fire event. The applicable... designed with a metal frame covered by fabric, not with large, non-metallic panels. Seats also met the then...

76 FR 26949 - Special Conditions: Boeing Model 747-8 Series Airplanes; Overhead Flight Attendant Rest Compartment

Science.gov (United States)

2011-05-10

.... A means to fight a fire must be provided. This can be either a built-in extinguishing system or... entering the OFAR compartment through the vestibule to fight a fire will examine the vestibule and the... occupant's first action should be to leave the confined space, unless the occupant(s) is fighting the fire...

76 FR 44246 - Special Conditions: Boeing Model 747-8 Series Airplanes; Overhead Flight Attendant Rest Compartment

Science.gov (United States)

2011-07-25

... sole means to fight a fire or to supplement a built-in extinguishing system of limited suppression... the vestibule to fight a fire will examine the vestibule and the lavatory areas for the source of the... occupant's first action should be to leave the confined space, unless the occupant(s) is fighting the fire...

78 FR 36084 - Special Conditions: The Boeing Company, Model 717-200 Series Airplanes; Seats With Inflatable...

Science.gov (United States)

2013-06-17

... percentile male. The inflatable lapbelt must provide a consistent approach to energy absorption throughout... interested people to take part in this rulemaking by sending written comments, data, or views. The most...

Acoustic results of the Boeing model 360 whirl tower test

Science.gov (United States)

Watts, Michael E.; Jordan, David

1990-09-01

An evaluation is presented for whirl tower test results of the Model 360 helicopter's advanced, high-performance four-bladed composite rotor system intended to facilitate over-200-knot flight. During these performance measurements, acoustic data were acquired by seven microphones. A comparison of whirl-tower tests with theory indicate that theoretical prediction accuracies vary with both microphone position and the inclusion of ground reflection. Prediction errors varied from 0 to 40 percent of the measured signal-to-peak amplitude.

Computer Modeling of the Effects of Atmospheric Conditions on Sound Signatures

Science.gov (United States)

2016-02-01

simulation. 11 5. References 1. Attenborough K. Sound propagation in the atmosphere. In: Rossing TD, editor. Springer handbook of...ARL-TR-7602 ● FEB 2016 US Army Research Laboratory Computer Modeling of the Effects of Atmospheric Conditions on Sound ...Laboratory Computer Modeling of the Effects of Atmospheric Conditions on Sound Signatures by Sarah Wagner Science and Engineering Apprentice

Selection Criteria in Regime Switching Conditional Volatility Models

Directory of Open Access Journals (Sweden)

Thomas Chuffart

2015-05-01

Full Text Available A large number of nonlinear conditional heteroskedastic models have been proposed in the literature. Model selection is crucial to any statistical data analysis. In this article, we investigate whether the most commonly used selection criteria lead to choice of the right specification in a regime switching framework. We focus on two types of models: the Logistic Smooth Transition GARCH and the Markov-Switching GARCH models. Simulation experiments reveal that information criteria and loss functions can lead to misspecification ; BIC sometimes indicates the wrong regime switching framework. Depending on the Data Generating Process used in the experiments, great care is needed when choosing a criterion.

Exact simulation of conditioned Wright-Fisher models.

Science.gov (United States)

Zhao, Lei; Lascoux, Martin; Waxman, David

2014-12-21

Forward and backward simulations play an increasing role in population genetics, in particular when inferring the relative importance of evolutionary forces. It is therefore important to develop fast and accurate simulation methods for general population genetics models. Here we present an exact simulation method that generates trajectories of an allele׳s frequency in a finite population, as described by a general Wright-Fisher model. The method generates conditioned trajectories that start from a known frequency at a known time, and which achieve a specific final frequency at a known final time. The simulation method applies irrespective of the smallness of the probability of the transition between the initial and final states, because it is not based on rejection of trajectories. We illustrate the method on several different populations where a Wright-Fisher model (or related) applies, namely (i) a locus with 2 alleles, that is subject to selection and mutation; (ii) a locus with 3 alleles, that is subject to selection; (iii) a locus in a metapopulation consisting of two subpopulations of finite size, that are subject to selection and migration. The simulation method allows the generation of conditioned trajectories that can be used for the purposes of visualisation, the estimation of summary statistics, and the development/testing of new inferential methods. The simulated trajectories provide a very simple approach to estimating quantities that cannot easily be expressed in terms of the transition matrix, and can be applied to finite Markov chains other than the Wright-Fisher model. Copyright © 2014 Elsevier Ltd. All rights reserved.

An Analysis of 20 Years of Space Weathering Effects on the Boeing 376 Spacecraft

Science.gov (United States)

Frith, James; Anz-Meador, Phillip; Cowardin, Heather; Buckalew, Brent; Lederer, Susan

2015-01-01

The Boeing HS-376 spin stabilized spacecraft was a popular design that was launched continuously into geosynchronous orbit starting in 1980, with the last launch occurring in 2003. Over 50 of the HS-376 buses were produced to fulfill a variety of different communication missions for countries all over the world. The design of the bus is easily approximated as a telescoping cylinder that is covered with solar cells and an Earth-facing antenna that is despun at the top of the cylinder. The similarity in design and the number of spacecraft launched over a long period of time make the HS-376 a prime target for studying the effects of solar weathering on solar panels as a function of time. A selection of primarily non-operational HS-376 spacecraft launched over a 20-year time period were observed using the United Kingdom Infrared Telescope on Mauna Kea and multi-band, near-infrared photometry produced. Each spacecraft was observed for an entire night cycling through ZYJHK filters and time-varying colors produced to compare near-infrared color as a function of launch date. The resulting analysis shown here may help in the future to set launch date constraints on the parent object of unidentified debris objects or other unknown spacecraft.

Modelling crop yield in Iberia under drought conditions

Science.gov (United States)

Ribeiro, Andreia; Páscoa, Patrícia; Russo, Ana; Gouveia, Célia

2017-04-01

The improved assessment of the cereal yield and crop loss under drought conditions are essential to meet the increasing economy demands. The growing frequency and severity of the extreme drought conditions in the Iberian Peninsula (IP) has been likely responsible for negative impacts on agriculture, namely on crop yield losses. Therefore, a continuous monitoring of vegetation activity and a reliable estimation of drought impacts is crucial to contribute for the agricultural drought management and development of suitable information tools. This works aims to assess the influence of drought conditions in agricultural yields over the IP, considering cereal yields from mainly rainfed agriculture for the provinces with higher productivity. The main target is to develop a strategy to model drought risk on agriculture for wheat yield at a province level. In order to achieve this goal a combined assessment was made using a drought indicator (Standardized Precipitation Evapotranspiration Index, SPEI) to evaluate drought conditions together with a widely used vegetation index (Normalized Difference Vegetation Index, NDVI) to monitor vegetation activity. A correlation analysis between detrended wheat yield and SPEI was performed in order to assess the vegetation response to each time scale of drought occurrence and also identify the moment of the vegetative cycle when the crop yields are more vulnerable to drought conditions. The time scales and months of SPEI, together with the months of NDVI, better related with wheat yield were chosen to perform a multivariate regression analysis to simulate crop yield. Model results are satisfactory and highlighted the usefulness of such analysis in the framework of developing a drought risk model for crop yields. In terms of an operational point of view, the results aim to contribute to an improved understanding of crop yield management under dry conditions, particularly adding substantial information on the advantages of combining

Physically-consistent wall boundary conditions for the k-ω turbulence model

DEFF Research Database (Denmark)

Fuhrman, David R.; Dixen, Martin; Jacobsen, Niels Gjøl

2010-01-01

A model solving Reynolds-averaged Navier–Stokes equations, coupled with k-v turbulence closure, is used to simulate steady channel flow on both hydraulically smooth and rough beds. Novel experimental data are used as model validation, with k measured directly from all three components of the fluc......A model solving Reynolds-averaged Navier–Stokes equations, coupled with k-v turbulence closure, is used to simulate steady channel flow on both hydraulically smooth and rough beds. Novel experimental data are used as model validation, with k measured directly from all three components...... of the fluctuating velocity signal. Both conventional k = 0 and dk/dy = 0 wall boundary conditions are considered. Results indicate that either condition can provide accurate solutions, for the bulk of the flow, over both smooth and rough beds. It is argued that the zero-gradient condition is more consistent...... with the near wall physics, however, as it allows direct integration through a viscous sublayer near smooth walls, while avoiding a viscous sublayer near rough walls. This is in contrast to the conventional k = 0 wall boundary condition, which forces resolution of a viscous sublayer in all circumstances...

New normative standards of conditional reasoning and the dual-source model.

Science.gov (United States)

Singmann, Henrik; Klauer, Karl Christoph; Over, David

2014-01-01

There has been a major shift in research on human reasoning toward Bayesian and probabilistic approaches, which has been called a new paradigm. The new paradigm sees most everyday and scientific reasoning as taking place in a context of uncertainty, and inference is from uncertain beliefs and not from arbitrary assumptions. In this manuscript we present an empirical test of normative standards in the new paradigm using a novel probabilized conditional reasoning task. Our results indicated that for everyday conditional with at least a weak causal connection between antecedent and consequent only the conditional probability of the consequent given antecedent contributes unique variance to predicting the probability of conditional, but not the probability of the conjunction, nor the probability of the material conditional. Regarding normative accounts of reasoning, we found significant evidence that participants' responses were confidence preserving (i.e., p-valid in the sense of Adams, 1998) for MP inferences, but not for MT inferences. Additionally, only for MP inferences and to a lesser degree for DA inferences did the rate of responses inside the coherence intervals defined by mental probability logic (Pfeifer and Kleiter, 2005, 2010) exceed chance levels. In contrast to the normative accounts, the dual-source model (Klauer et al., 2010) is a descriptive model. It posits that participants integrate their background knowledge (i.e., the type of information primary to the normative approaches) and their subjective probability that a conclusion is seen as warranted based on its logical form. Model fits showed that the dual-source model, which employed participants' responses to a deductive task with abstract contents to estimate the form-based component, provided as good an account of the data as a model that solely used data from the probabilized conditional reasoning task.

New Normative Standards of Conditional Reasoning and the Dual-Source Model

Directory of Open Access Journals (Sweden)

Henrik eSingmann

2014-04-01

Full Text Available There has been a major shift in research on human reasoning towards Bayesian and probabilistic approaches, which has been called a new paradigm. The new paradigm sees most everyday and scientific reasoning as taking place in a context of uncertainty, and inference is from uncertain beliefs and not from arbitrary assumptions. In this manuscript we present an empirical test of normative standards in the new paradigm using a novel probabilized conditional reasoning task. Our results indicated that for everyday conditional with at least a weak causal connection between antecedent and consequent only the conditional probability of the consequent given antecedent contributes unique variance to predicting the probability of conditional, but not the probability of the conjunction, nor the probability of the material conditional. Regarding normative accounts of reasoning, we found significant evidence that participants' responses were confidence preserving (i.e., p-valid in the sense of Adams, 1998 for MP inferences, but not for MT inferences. Additionally, only for MP inferences and to a lesser degree for DA inferences did the rate of responses inside the coherence intervals defined by mental probability logic (Pfeifer & Kleiter, 2005, 2010 exceed chance levels. In contrast to the normative accounts, the dual-source model (Klauer, Beller, & Hütter, 2010 is a descriptive model. It posits that participants integrate their background knowledge (i.e., the type of information primary to the normative approaches and their subjective probability that a conclusion is seen as warranted based on its logical form. Model fits showed that the dual-source model, which employed participants' responses to a deductive task with abstract contents to estimate the form-based component, provided as good an account of the data as a model that solely used data from the probabilized conditional reasoning task.

Electric machines modeling, condition monitoring, and fault diagnosis

CERN Document Server

Toliyat, Hamid A; Choi, Seungdeog; Meshgin-Kelk, Homayoun

2012-01-01

With countless electric motors being used in daily life, in everything from transportation and medical treatment to military operation and communication, unexpected failures can lead to the loss of valuable human life or a costly standstill in industry. To prevent this, it is important to precisely detect or continuously monitor the working condition of a motor. Electric Machines: Modeling, Condition Monitoring, and Fault Diagnosis reviews diagnosis technologies and provides an application guide for readers who want to research, develop, and implement a more effective fault diagnosis and condi

Modelling of the Contact Condition at the Tool/Matrix Interface in Friction Stir Welding

DEFF Research Database (Denmark)

Schmidt, Henrik Nikolaj Blich; Hattel, Jesper; Wert, John

2003-01-01

a known contact condition at the contact interface, e.g. either as pure sliding or sticking. The present model uses Coulomb’s law of friction for the sliding condition and the material yield shear stress for the sticking condition to model the contact forces. The model includes heat generation...

Modeling long period swell in Southern California: Practical boundary conditions from buoy observations and global wave model predictions

Science.gov (United States)

Crosby, S. C.; O'Reilly, W. C.; Guza, R. T.

2016-02-01

Accurate, unbiased, high-resolution (in space and time) nearshore wave predictions are needed to drive models of beach erosion, coastal flooding, and alongshore transport of sediment, biota and pollutants. On highly sheltered shorelines, wave predictions are sensitive to the directions of onshore propagating waves, and nearshore model prediction error is often dominated by uncertainty in offshore boundary conditions. Offshore islands and shoals, and coastline curvature, create complex sheltering patterns over the 250km span of southern California (SC) shoreline. Here, regional wave model skill in SC was compared for different offshore boundary conditions created using offshore buoy observations and global wave model hindcasts (National Oceanographic and Atmospheric Administration Wave Watch 3, WW3). Spectral ray-tracing methods were used to transform incident offshore swell (0.04-0.09Hz) energy at high directional resolution (1-deg). Model skill is assessed for predictions (wave height, direction, and alongshore radiation stress) at 16 nearshore buoy sites between 2000 and 2009. Model skill using buoy-derived boundary conditions is higher than with WW3-derived boundary conditions. Buoy-driven nearshore model results are similar with various assumptions about the true offshore directional distribution (maximum entropy, Bayesian direct, and 2nd derivative smoothness). Two methods combining offshore buoy observations with WW3 predictions in the offshore boundary condition did not improve nearshore skill above buoy-only methods. A case example at Oceanside harbor shows strong sensitivity of alongshore sediment transport predictions to different offshore boundary conditions. Despite this uncertainty in alongshore transport magnitude, alongshore gradients in transport (e.g. the location of model accretion and erosion zones) are determined by the local bathymetry, and are similar for all predictions.

Estimation of antecedent wetness conditions for flood modelling in northern Morocco

Directory of Open Access Journals (Sweden)

Y. Tramblay

2012-11-01

Full Text Available In northern Morocco are located most of the dams and reservoirs of the country, while this region is affected by severe rainfall events causing floods. To improve the management of the water regulation structures, there is a need to develop rainfall–runoff models to both maximize the storage capacity and reduce the risks caused by floods. In this study, a model is developed to reproduce the flood events for a 655 km² catchment located upstream of the 6th largest dam in Morocco. Constrained by data availability, a standard event-based model combining a SCS-CN (Soil Conservation Service Curve Number loss model and a Clark unit hydrograph was developed for hourly discharge simulation using 16 flood events that occurred between 1984 and 2008. The model was found satisfactory to reproduce the runoff and the temporal evolution of floods, even with limited rainfall data. Several antecedent wetness conditions estimators for the catchment were compared with the initial condition of the model. Theses estimators include an antecedent discharge index, an antecedent precipitation index and a continuous daily soil moisture accounting model (SMA, based on precipitation and evapotranspiration. The SMA model performed the best to estimate the initial conditions of the event-based hydrological model (R² = 0.9. Its daily output has been compared with ASCAT and AMSR-E remote sensing data products, which were both able to reproduce with accuracy the daily simulated soil moisture dynamics at the catchment scale. This same approach could be implemented in other catchments of this region for operational purposes. The results of this study suggest that remote sensing data are potentially useful to estimate the soil moisture conditions in the case of ungauged catchments in Northern Africa.

Modeling variations in the cedi/dollar exchange rate in Ghana: an autoregressive conditional heteroscedastic (ARCH) models.

Science.gov (United States)

Techie Quaicoe, Michael; Twenefour, Frank B K; Baah, Emmanuel M; Nortey, Ezekiel N N

2015-01-01

This research article aimed at modeling the variations in the dollar/cedi exchange rate. It examines the applicability of a range of ARCH/GARCH specifications for modeling volatility of the series. The variants considered include the ARMA, GARCH, IGARCH, EGARCH and M-GARCH specifications. The results show that the series was non stationary which resulted from the presence of a unit root in it. The ARMA (1, 1) was found to be the most suitable model for the conditional mean. From the Box-Ljung test statistics x-squared of 1476.338 with p value 0.00217 for squared returns and 16.918 with 0.0153 p values for squared residuals, the null hypothesis of no ARCH effect was rejected at 5% significance level indicating the presence of an ARCH effect in the series. ARMA (1, 1) + GARCH (1, 1) which has all parameters significant was found to be the most suitable model for the conditional mean with conditional variance, thus showing adequacy in describing the conditional mean with variance of the return series at 5% significant level. A 24 months forecast for the mean actual exchange rates and mean returns from January, 2013 to December, 2014 made also showed that the fitted model is appropriate for the data and a depreciating trend of the cedi against the dollar for forecasted period respectively.

Diffusion modeling of fission product release during depressurized core conduction cooldown conditions

International Nuclear Information System (INIS)

Martin, R.C.

1991-01-01

A simple model for diffusion through the silicon carbide layer of TRISO particles is applied to the data for accident condition testing of fuel spheres for the High-Temperature Reactor program of the Federal Republic of Germany (FRG). Categorization of sphere release of 137 Cs based on fast neutron fluence permits predictions of release with an accuracy comparable to that of the US/FRG accident condition fuel performance model. Calculations are also performed for 85 Kr, 90 Sr, and 110m Ag. Diffusion of cesium through SiC suggests that models of fuel failure should consider fuel performance during repeated accident condition thermal cycling. Microstructural considerations in models of fission product release are discussed. The neutron-induced segregation of silicon within the SiC structure is postulated as a mechanism for enhanced fission product release during accident conditions. As oxygen-enhanced SiC decomposition mechanism is also discussed. (author). 12 refs, 11 figs, 2 tabs

Modeling the Process of Event Sequence Data Generated for Working Condition Diagnosis

Directory of Open Access Journals (Sweden)

Jianwei Ding

2015-01-01

Full Text Available Condition monitoring systems are widely used to monitor the working condition of equipment, generating a vast amount and variety of telemetry data in the process. The main task of surveillance focuses on analyzing these routinely collected telemetry data to help analyze the working condition in the equipment. However, with the rapid increase in the volume of telemetry data, it is a nontrivial task to analyze all the telemetry data to understand the working condition of the equipment without any a priori knowledge. In this paper, we proposed a probabilistic generative model called working condition model (WCM, which is capable of simulating the process of event sequence data generated and depicting the working condition of equipment at runtime. With the help of WCM, we are able to analyze how the event sequence data behave in different working modes and meanwhile to detect the working mode of an event sequence (working condition diagnosis. Furthermore, we have applied WCM to illustrative applications like automated detection of an anomalous event sequence for the runtime of equipment. Our experimental results on the real data sets demonstrate the effectiveness of the model.

Circular Conditional Autoregressive Modeling of Vector Fields.

Science.gov (United States)

Modlin, Danny; Fuentes, Montse; Reich, Brian

2012-02-01

As hurricanes approach landfall, there are several hazards for which coastal populations must be prepared. Damaging winds, torrential rains, and tornadoes play havoc with both the coast and inland areas; but, the biggest seaside menace to life and property is the storm surge. Wind fields are used as the primary forcing for the numerical forecasts of the coastal ocean response to hurricane force winds, such as the height of the storm surge and the degree of coastal flooding. Unfortunately, developments in deterministic modeling of these forcings have been hindered by computational expenses. In this paper, we present a multivariate spatial model for vector fields, that we apply to hurricane winds. We parameterize the wind vector at each site in polar coordinates and specify a circular conditional autoregressive (CCAR) model for the vector direction, and a spatial CAR model for speed. We apply our framework for vector fields to hurricane surface wind fields for Hurricane Floyd of 1999 and compare our CCAR model to prior methods that decompose wind speed and direction into its N-S and W-E cardinal components.

Partitioning uncertainty in streamflow projections under nonstationary model conditions

Science.gov (United States)

Chawla, Ila; Mujumdar, P. P.

2018-02-01

Assessing the impacts of Land Use (LU) and climate change on future streamflow projections is necessary for efficient management of water resources. However, model projections are burdened with significant uncertainty arising from various sources. Most of the previous studies have considered climate models and scenarios as major sources of uncertainty, but uncertainties introduced by land use change and hydrologic model assumptions are rarely investigated. In this paper an attempt is made to segregate the contribution from (i) general circulation models (GCMs), (ii) emission scenarios, (iii) land use scenarios, (iv) stationarity assumption of the hydrologic model, and (v) internal variability of the processes, to overall uncertainty in streamflow projections using analysis of variance (ANOVA) approach. Generally, most of the impact assessment studies are carried out with unchanging hydrologic model parameters in future. It is, however, necessary to address the nonstationarity in model parameters with changing land use and climate. In this paper, a regression based methodology is presented to obtain the hydrologic model parameters with changing land use and climate scenarios in future. The Upper Ganga Basin (UGB) in India is used as a case study to demonstrate the methodology. The semi-distributed Variable Infiltration Capacity (VIC) model is set-up over the basin, under nonstationary conditions. Results indicate that model parameters vary with time, thereby invalidating the often-used assumption of model stationarity. The streamflow in UGB under the nonstationary model condition is found to reduce in future. The flows are also found to be sensitive to changes in land use. Segregation results suggest that model stationarity assumption and GCMs along with their interactions with emission scenarios, act as dominant sources of uncertainty. This paper provides a generalized framework for hydrologists to examine stationarity assumption of models before considering them

The use of vestibular models for design and evaluation of flight simulator motion

Science.gov (United States)

Bussolari, Steven R.; Young, Laurence R.; Lee, Alfred T.

1989-01-01

Quantitative models for the dynamics of the human vestibular system are applied to the design and evaluation of flight simulator platform motion. An optimal simulator motion control algorithm is generated to minimize the vector difference between perceived spatial orientation estimated in flight and in simulation. The motion controller has been implemented on the Vertical Motion Simulator at NASA Ames Research Center and evaluated experimentally through measurement of pilot performance and subjective rating during VTOL aircraft simulation. In general, pilot performance in a longitudinal tracking task (formation flight) did not appear to be sensitive to variations in platform motion condition as long as motion was present. However, pilot assessment of motion fidelity by means of a rating scale designed for this purpose, were sensitive to motion controller design. Platform motion generated with the optimal motion controller was found to be generally equivalent to that generated by conventional linear crossfeed washout. The vestibular models are used to evaluate the motion fidelity of transport category aircraft (Boeing 727) simulation in a pilot performance and simulator acceptability study at the Man-Vehicle Systems Research Facility at NASA Ames Research Center. Eighteen airline pilots, currently flying B-727, were given a series of flight scenarios in the simulator under various conditions of simulator motion. The scenarios were chosen to reflect the flight maneuvers that these pilots might expect to be given during a routine pilot proficiency check. Pilot performance and subjective rating of simulator fidelity was relatively insensitive to the motion condition, despite large differences in the amplitude of motion provided. This lack of sensitivity may be explained by means of the vestibular models, which predict little difference in the modeled motion sensations of the pilots when different motion conditions are imposed.

Conformal Extensions of the Standard Model with Veltman Conditions

DEFF Research Database (Denmark)

Antipin, Oleg; Mojaza, Matin; Sannino, Francesco

2014-01-01

Using the renormalisation group framework we classify different extensions of the standard model according to their degree of naturality. A new relevant class of perturbative models involving elementary scalars is the one in which the theory simultaneously satisfies the Veltman conditions...... and is conformal at the classical level. We term these extensions perturbative natural conformal (PNC) theories. We show that PNC models are very constrained and thus highly predictive. Among the several PNC examples that we exhibit, we discover a remarkably simple PNC extension of the standard model in which...

Marine Vessel Models in Changing Operational Conditions - A Tutorial

DEFF Research Database (Denmark)

Perez, Tristan; Sørensen, Asgeir; Blanke, Mogens

2006-01-01

conditions (VOC). However, since marine systems operate in changing VOCs, there is a need to adapt the models. To date, there is no theory available to describe a general model valid across different VOCs due to the complexity of the hydrodynamic involved. It is believed that system identification could......This tutorial paper provides an introduction, from a systems perspective, to the topic of ship motion dynamics of surface ships. It presents a classification of parametric models currently used for monitoring and control of marine vessels. These models are valid for certain vessel operational...

Modelling cladding response to changing conditions

Energy Technology Data Exchange (ETDEWEB)

Tulkki, Ville; Ikonen, Timo [VTT Technical Research Centre of Finland ltd (Finland)

2016-11-15

The cladding of the nuclear fuel is subjected to varying conditions during fuel reactor life. Load drops and reversals can be modelled by taking cladding viscoelastic behaviour into account. Viscoelastic contribution to the deformation of metals is usually considered small enough to be ignored, and in many applications it merely contributes to the primary part of the creep curve. With nuclear fuel cladding the high temperature and irradiation as well as the need to analyse the variable load all emphasise the need to also inspect the viscoelasticity of the cladding.

Oblique radiation lateral open boundary conditions for a regional climate atmospheric model

Science.gov (United States)

Cabos Narvaez, William; De Frutos Redondo, Jose Antonio; Perez Sanz, Juan Ignacio; Sein, Dmitry

2013-04-01

The prescription of lateral boundary conditions in regional atmospheric models represent a very important issue for limited area models. The ill-posed nature of the open boundary conditions makes it necessary to devise schemes in order to filter spurious wave reflections at boundaries, being desirable to have one boundary condition per variable. On the other side, due to the essentially hyperbolic nature of the equations solved in state of the art atmospheric models, external data is required only for inward boundary fluxes. These circumstances make radiation lateral boundary conditions a good choice for the filtering of spurious wave reflections. Here we apply the adaptive oblique radiation modification proposed by Mikoyada and Roseti to each of the prognostic variables of the REMO regional atmospheric model and compare it to the more common normal radiation condition used in REMO. In the proposed scheme, special attention is paid to the estimation of the radiation phase speed, essential to detecting the direction of boundary fluxes. One of the differences with the classical scheme is that in case of outward propagation, the adaptive nudging imposed in the boundaries allows to minimize under and over specifications problems, adequately incorporating the external information.

Slarti: A boundary condition editor for a coupled climate model

Science.gov (United States)

Mickelson, S. A.; Jacob, R. L.; Pierrehumbert, R.

2006-12-01

One of the largest barriers to making climate models more flexible is the difficulty in creating new boundary conditions, especially for "deep time" paleoclimate cases where continents are in different positions. Climate models consist of several mutually-interacting component models and the boundary conditions must be consistent between them. We have developed a program called Slarti which uses a Graphical User Interface and a set of consistency rules to aid researchers in creating new, consistent, boundary condition files for the Fast Ocean Atmosphere Model (FOAM). Users can start from existing mask, topography, or bathymetry data or can build a "world" entirely from scratch (e.g. a single island continent). Once a case has been started, users can modify mask, vegetation, bathymetry, topography, and river flow fields by drawing new data through a "paint" interface. Users activate a synchronization button which goes through the fields to eliminate inconsistencies. When the changes are complete and save is selected, Slarti creates all the necessary files for an initial run of FOAM. The data is edited at the highest resolution (the ocean-land surface in FOAM) and then interpolated to the atmosphere resolution. Slarti was implemented in Java to maintain portability across platforms. We also relied heavily on Java Swing components to create the interface. This allowed us to create an object-oriented interface that could be used on many different systems. Since Slarti allows users to visualize their changes, they are able to see areas that may cause problems when the model is ran. Some examples would be lakes from the river flow field and narrow trenches within the bathymetry. Through different checks and options available through its interface, Slarti makes the process of creating new boundary conditions for FOAM easier and faster while reducing the chance for user errors.

A hybrid prognostic model for multistep ahead prediction of machine condition

Science.gov (United States)

Roulias, D.; Loutas, T. H.; Kostopoulos, V.

2012-05-01

Prognostics are the future trend in condition based maintenance. In the current framework a data driven prognostic model is developed. The typical procedure of developing such a model comprises a) the selection of features which correlate well with the gradual degradation of the machine and b) the training of a mathematical tool. In this work the data are taken from a laboratory scale single stage gearbox under multi-sensor monitoring. Tests monitoring the condition of the gear pair from healthy state until total brake down following several days of continuous operation were conducted. After basic pre-processing of the derived data, an indicator that correlated well with the gearbox condition was obtained. Consecutively the time series is split in few distinguishable time regions via an intelligent data clustering scheme. Each operating region is modelled with a feed-forward artificial neural network (FFANN) scheme. The performance of the proposed model is tested by applying the system to predict the machine degradation level on unseen data. The results show the plausibility and effectiveness of the model in following the trend of the timeseries even in the case that a sudden change occurs. Moreover the model shows ability to generalise for application in similar mechanical assets.

Statistical models based on conditional probability distributions

International Nuclear Information System (INIS)

Narayanan, R.S.

1991-10-01

We present a formulation of statistical mechanics models based on conditional probability distribution rather than a Hamiltonian. We show that it is possible to realize critical phenomena through this procedure. Closely linked with this formulation is a Monte Carlo algorithm, in which a configuration generated is guaranteed to be statistically independent from any other configuration for all values of the parameters, in particular near the critical point. (orig.)

Modelling of air-conditioned and heated spaces

Energy Technology Data Exchange (ETDEWEB)

Moehl, U

1987-01-01

A space represents a complex system involving numerous components, manipulated variables and disturbances which need to be described if dynamic behaviour of space air is to be determined. A justifiable amount of simulation input is determined by the application of adjusted modelling of the individual components. The determination of natural air exchange in heated spaces and of space-air flow in air-conditioned space are a primary source of uncertainties. (orig.).

An Improved Matlab-Simulink Model of PV Module considering Ambient Conditions

Directory of Open Access Journals (Sweden)

R. Ayaz

2014-01-01

Full Text Available A photovoltaic (PV model is proposed on Matlab/Simulink environment considering the real atmospheric conditions and this PV model is tested with different PV panels technologies (monocrystalline silicon, polycrystalline silicon, and thin film. The meteorological data of Istanbul—the location of the study—such as irradiance, cell temperature, and wind speed are taken into account in the proposed model for each technology. Eventually, the power outputs of the PV module under real atmospheric conditions are measured for resistive loading and these powers are compared with the results of proposed PV model. As a result of the comparison, it is shown that the proposed model is more compatible for monocrystal silicon and thin-film modules; however, it does not show a good correlation with polycrystalline silicon PV module.

Modeling of hydrologic conditions and solute movement in processed oil shale waste embankments under simulated climatic conditions

International Nuclear Information System (INIS)

Reeves, T.L.; Turner, J.P.; Hasfurther, V.R.; Skinner, Q.D.

1992-06-01

The scope of this program is to study interacting hydrologic, geotechnical, and chemical factors affecting the behavior and disposal of combusted processed oil shale. The research combines bench-scale testing with large scale research sufficient to describe commercial scale embankment behavior. The large scale approach was accomplished by establishing five lysimeters, each 7.3 x 3.0 x 3.0 m deep, filled with processed oil shale that has been retorted and combusted by the Lurgi-Ruhrgas (Lurgi) process. Approximately 400 tons of Lurgi processed oil shale waste was provided by RBOSC to carry out this study. Research objectives were designed to evaluate hydrologic, geotechnical, and chemical properties and conditions which would affect the design and performance of large-scale embankments. The objectives of this research are: assess the unsaturated movement and redistribution of water and the development of potential saturated zones and drainage in disposed processed oil shale under natural and simulated climatic conditions; assess the unsaturated movement of solubles and major chemical constituents in disposed processed oil shale under natural and simulated climatic conditions; assess the physical and constitutive properties of the processed oil shale and determine potential changes in these properties caused by disposal and weathering by natural and simulated climatic conditions; assess the use of previously developed computer model(s) to describe the infiltration, unsaturated movement, redistribution, and drainage of water in disposed processed oil shale; evaluate the stability of field scale processed oil shale solid waste embankments using computer models

Significance of settling model structures and parameter subsets in modelling WWTPs under wet-weather flow and filamentous bulking conditions.

Science.gov (United States)

Ramin, Elham; Sin, Gürkan; Mikkelsen, Peter Steen; Plósz, Benedek Gy

2014-10-15

Current research focuses on predicting and mitigating the impacts of high hydraulic loadings on centralized wastewater treatment plants (WWTPs) under wet-weather conditions. The maximum permissible inflow to WWTPs depends not only on the settleability of activated sludge in secondary settling tanks (SSTs) but also on the hydraulic behaviour of SSTs. The present study investigates the impacts of ideal and non-ideal flow (dry and wet weather) and settling (good settling and bulking) boundary conditions on the sensitivity of WWTP model outputs to uncertainties intrinsic to the one-dimensional (1-D) SST model structures and parameters. We identify the critical sources of uncertainty in WWTP models through global sensitivity analysis (GSA) using the Benchmark simulation model No. 1 in combination with first- and second-order 1-D SST models. The results obtained illustrate that the contribution of settling parameters to the total variance of the key WWTP process outputs significantly depends on the influent flow and settling conditions. The magnitude of the impact is found to vary, depending on which type of 1-D SST model is used. Therefore, we identify and recommend potential parameter subsets for WWTP model calibration, and propose optimal choice of 1-D SST models under different flow and settling boundary conditions. Additionally, the hydraulic parameters in the second-order SST model are found significant under dynamic wet-weather flow conditions. These results highlight the importance of developing a more mechanistic based flow-dependent hydraulic sub-model in second-order 1-D SST models in the future. Copyright © 2014 Elsevier Ltd. All rights reserved.

A note on intrinsic conditional autoregressive models for disconnected graphs

KAUST Repository

Freni-Sterrantino, Anna

2018-05-23

In this note we discuss (Gaussian) intrinsic conditional autoregressive (CAR) models for disconnected graphs, with the aim of providing practical guidelines for how these models should be defined, scaled and implemented. We show how these suggestions can be implemented in two examples, on disease mapping.

A note on intrinsic conditional autoregressive models for disconnected graphs

KAUST Repository

Freni-Sterrantino, Anna; Ventrucci, Massimo; Rue, Haavard

2018-01-01

In this note we discuss (Gaussian) intrinsic conditional autoregressive (CAR) models for disconnected graphs, with the aim of providing practical guidelines for how these models should be defined, scaled and implemented. We show how these suggestions can be implemented in two examples, on disease mapping.

Water loss in table grapes: model development and validation under dynamic storage conditions

Directory of Open Access Journals (Sweden)

Ericsem PEREIRA

2017-09-01

Full Text Available Abstract Water loss is a critical problem affecting the quality of table grapes. Temperature and relative humidity (RH are essential in this process. Although mathematical modelling can be applied to measure constant temperature and RH impacts, it is proved that variations in storage conditions are normally encountered in the cold chain. This study proposed a methodology to develop a weight loss model for table grapes and validate its predictions in non-constant conditions of a domestic refrigerator. Grapes were maintained under controlled conditions and the weight loss was measured to calibrate the model. The model described the water loss process adequately and the validation tests confirmed its predictive ability. Delayed cooling tests showed that estimated transpiration rates in subsequent continuous temperature treatment was not significantly influenced by prior exposure conditions, suggesting that this model may be useful to estimate the weight loss consequences of interruptions in the cold chain.

Compositional models and conditional independence in evidence theory

Czech Academy of Sciences Publication Activity Database

Jiroušek, Radim; Vejnarová, Jiřina

2011-01-01

Roč. 52, č. 3 (2011), s. 316-334 ISSN 0888-613X Institutional research plan: CEZ:AV0Z10750506 Keywords : Evidence theory * Conditional independence * multidimensional models Subject RIV: BA - General Mathematics Impact factor: 1.948, year: 2011 http://library.utia.cas.cz/separaty/2012/MTR/jirousek-0370515.pdf

Illusory inferences from a disjunction of conditionals: a new mental models account.

Science.gov (United States)

Barrouillet, P; Lecas, J F

2000-08-14

(Johnson-Laird, P.N., & Savary, F. (1999, Illusory inferences: a novel class of erroneous deductions. Cognition, 71, 191-229.) have recently presented a mental models account, based on the so-called principle of truth, for the occurrence of inferences that are compelling but invalid. This article presents an alternative account of the illusory inferences resulting from a disjunction of conditionals. In accordance with our modified theory of mental models of the conditional, we show that the way individuals represent conditionals leads them to misinterpret the locus of the disjunction and prevents them from drawing conclusions from a false conditional, thus accounting for the compelling character of the illusory inference.

Condition Parameter Modeling for Anomaly Detection in Wind Turbines

Directory of Open Access Journals (Sweden)

Yonglong Yan

2014-05-01

Full Text Available Data collected from the supervisory control and data acquisition (SCADA system, used widely in wind farms to obtain operational and condition information about wind turbines (WTs, is of important significance for anomaly detection in wind turbines. The paper presents a novel model for wind turbine anomaly detection mainly based on SCADA data and a back-propagation neural network (BPNN for automatic selection of the condition parameters. The SCADA data sets are determined through analysis of the cumulative probability distribution of wind speed and the relationship between output power and wind speed. The automatic BPNN-based parameter selection is for reduction of redundant parameters for anomaly detection in wind turbines. Through investigation of cases of WT faults, the validity of the automatic parameter selection-based model for WT anomaly detection is verified.

Discounted cost model for condition-based maintenance optimization

International Nuclear Information System (INIS)

Weide, J.A.M. van der; Pandey, M.D.; Noortwijk, J.M. van

2010-01-01

This paper presents methods to evaluate the reliability and optimize the maintenance of engineering systems that are damaged by shocks or transients arriving randomly in time and overall degradation is modeled as a cumulative stochastic point process. The paper presents a conceptually clear and comprehensive derivation of formulas for computing the discounted cost associated with a maintenance policy combining both condition-based and age-based criteria for preventive maintenance. The proposed discounted cost model provides a more realistic basis for optimizing the maintenance policies than those based on the asymptotic, non-discounted cost rate criterion.

Conditioning a segmented stem profile model for two diameter measurements

Science.gov (United States)

Raymond L. Czaplewski; Joe P. Mcclure

1988-01-01

The stem profile model of Max and Burkhart (1976) is conditioned for dbh and a second upper stem measurement. This model was applied to a loblolly pine data set using diameter outside bark at 5.3m (i.e., height of 17.3 foot Girard form class) as the second upper stem measurement, and then compared to the original, unconditioned model. Variance of residuals was reduced...

On the role of model depth and hydraulic properties for groundwater flow modelling during glacial climate conditions

International Nuclear Information System (INIS)

Vidstrand, Patrik; Rhen, Ingvar

2011-03-01

A common assumption in regional groundwater flow simulations of periods with glacial climate conditions is that the salinity at the bottom boundary of the model domain is stable (constant over time). This assumption is partly based on the general fact that water density increases with increasing salinity, but also supported by measurements, e.g. the mobile (fracture water) and immobile (porewater) salinity typically increase with depth, whereas the conductive fracture frequency and fracture transmissivity often decrease with depth. Plausibly, the depth to stable hydrogeological conditions varies between sites, and the question studied here is whether hydrogeological disturbances could occur at 2-4 km depth during glacial climate conditions. With regard to the results of SDM-Site and SR-Site, the hydrogeological conditions at repository depth indicate less groundwater flow during glacial climate conditions at Forsmark than at Laxemar. For this reason, this study uses the Laxemar site as a hypothetical site of potentially more permeable conditions, hence more readily affected during glacial climate conditions. A series of flow simulations conducted with DarcyTools in an approximately 5 km deep, super-regional model domain centred on the Laxemar site are reported. The studied cases (model variants) represent a variety of different property specifications along with variations in initial conditions concerning salinity. The model domain is subjected to a transient top boundary representing an advancing ice sheet margin. The behaviour of the grid cell pressure, Darcy flux and mobile salinity is monitored at four different elevations along a vertical scan line through the centre of the suggested location for a KBS-3 repository at Laxemar. The studied monitoring points are located at -0.5 km, -2.5 km, -3.0 km, and -3.5 km. These elevations are chosen with the objective to study the range of hydrogeological disturbance that could occur at 2-4 km depth. The flow model is run

On the role of model depth and hydraulic properties for groundwater flow modelling during glacial climate conditions

Energy Technology Data Exchange (ETDEWEB)

Vidstrand, Patrik (TerraSolve AB (Sweden)); Rhen, Ingvar (SWECO Environment AB (Sweden))

2011-03-15

A common assumption in regional groundwater flow simulations of periods with glacial climate conditions is that the salinity at the bottom boundary of the model domain is stable (constant over time). This assumption is partly based on the general fact that water density increases with increasing salinity, but also supported by measurements, e.g. the mobile (fracture water) and immobile (porewater) salinity typically increase with depth, whereas the conductive fracture frequency and fracture transmissivity often decrease with depth. Plausibly, the depth to stable hydrogeological conditions varies between sites, and the question studied here is whether hydrogeological disturbances could occur at 2-4 km depth during glacial climate conditions. With regard to the results of SDM-Site and SR-Site, the hydrogeological conditions at repository depth indicate less groundwater flow during glacial climate conditions at Forsmark than at Laxemar. For this reason, this study uses the Laxemar site as a hypothetical site of potentially more permeable conditions, hence more readily affected during glacial climate conditions. A series of flow simulations conducted with DarcyTools in an approximately 5 km deep, super-regional model domain centred on the Laxemar site are reported. The studied cases (model variants) represent a variety of different property specifications along with variations in initial conditions concerning salinity. The model domain is subjected to a transient top boundary representing an advancing ice sheet margin. The behaviour of the grid cell pressure, Darcy flux and mobile salinity is monitored at four different elevations along a vertical scan line through the centre of the suggested location for a KBS-3 repository at Laxemar. The studied monitoring points are located at -0.5 km, -2.5 km, -3.0 km, and -3.5 km. These elevations are chosen with the objective to study the range of hydrogeological disturbance that could occur at 2-4 km depth. The flow model is run

Development of a butterfly check valve model under natural circulation conditions

International Nuclear Information System (INIS)

Rao, Yuxian; Yu, Lei; Fu, Shengwei; Zhang, Fan

2015-01-01

Highlights: • Bases on Lim’s swing check valve model, a butterfly check valve model was developed. • The method to quantify the friction torque T F in Li’s model was corrected. • The developed model was implemented into the RELAP5 code and verified. - Abstract: A butterfly check valve is widely used to prevent a reverse flow in the pipe lines of a marine nuclear power plant. Under some conditions, the natural circulation conditions in particular, the fluid velocity through the butterfly check valve might become too low to hold the valve disk fully open, thereby the flow resistance of the butterfly check valve varies with the location of the valve disk and as a result the fluid flow is significantly affected by the dynamic motion of the valve disk. Simulation of a pipe line that includes some butterfly check valves, especially under natural circulation conditions, is thus complicated. This paper focuses on the development of a butterfly check valve model to enhance the capability of the thermal–hydraulic system code and the developed model is implemented into the RELAP5 code. Both steady-state calculations and transient calculations were carried out for the primary loop system of a marine nuclear power plant and the calculation results are compared with the experimental data for verification purpose. The simulation results show an agreement with the experimental data

Three-party quantum teleportation using thermal states in Heisenberg XX model with open boundary condition

International Nuclear Information System (INIS)

Bhan, Jaemi; Kwon, Younghun

2007-01-01

Recently Yeo showed that thermal states in Heisenberg XX model with periodic boundary condition could be used for three-party quantum teleportation. However it is hard to implement the periodic boundary condition in spin chain. So instead of imposing the periodic boundary condition, we consider open boundary condition in Heisenberg XX model and investigate the possibility of using thermal states in Heisenberg XX model with open boundary condition. Using this way, we find the best fidelity conditions to three known protocols in three-party quantum teleportation. It turns out that the best fidelity in every protocol would be 23

A review on condition-based maintenance optimization models for stochastically deteriorating system

International Nuclear Information System (INIS)

Alaswad, Suzan; Xiang, Yisha

2017-01-01

Condition-based maintenance (CBM) is a maintenance strategy that collects and assesses real-time information, and recommends maintenance decisions based on the current condition of the system. In recent decades, research on CBM has been rapidly growing due to the rapid development of computer-based monitoring technologies. Research studies have proven that CBM, if planned properly, can be effective in improving equipment reliability at reduced costs. This paper presents a review of CBM literature with emphasis on mathematical modeling and optimization approaches. We focus this review on important aspects of the CBM, such as optimization criteria, inspection frequency, maintenance degree, solution methodology, etc. Since the modeling choice for the stochastic deterioration process greatly influences CBM strategy decisions, this review classifies the literature on CBM models based on the underlying deterioration processes, namely discrete- and continuous-state deterioration, and proportional hazard model. CBM models for multi-unit systems are also reviewed in this paper. This paper provides useful references for CBM management professionals and researchers working on CBM modeling and optimization. - Highlights: • A review on Condition-based maintenance (CBM) optimization models is presented. • The CBM models are classified based on the underlying deterioration processes. • Existing CBM models for both single- and multi-unit systems are reviewed. • Future essential research directions on CBM are identified.

Modeling Conditional Volatility of Indian Banking Sector’s Stock Market Returns

Directory of Open Access Journals (Sweden)

Singh Amanjot

2017-10-01

Full Text Available The study attempts to capture conditional variance of Indian banking sector’s stock market returns across the years 2005 to 2015 by employing different GARCH based symmetric and asymmetric models. The results report existence of persistency as well as leverage effects in the banking sector return volatility. On an expected note, the global financial crisis increased conditional volatility in the Indian banking sector during the years 2007 to 2009; further evidenced from Markov regime switches. The exponential GARCH (EGARCH model is found to be the best fit model capturing time-varying variance in the banking sector. The results support strong implications for the market participants at the time of devising portfolio management strategies.

76 FR 71865 - Special Conditions: Gulfstream Aerospace Corporation, Model GVI Airplane; Windshield Coating in...

Science.gov (United States)

2011-11-21

...; Special Conditions No. 25-452-SC] Special Conditions: Gulfstream Aerospace Corporation, Model GVI Airplane... Aerospace Corporation Model GVI airplane. This airplane will have a novel or unusual design feature(s..., Gulfstream Aerospace Corporation (GAC) applied for an FAA type certificate for its new Model GVI passenger...

CFD Modeling of Non-Neutral Atmospheric Boundary Layer Conditions

DEFF Research Database (Denmark)

Koblitz, Tilman

model results. A method is developed how to simulate the time-dependant non-neutral ABL flow over complex terrain: a precursor simulation is used to specify unsteady inlet boundary conditions on complex terrain domains. The advantage of the developed RANS model framework is its general applicability...... characteristics of neutral and non-neutral ABL flow. The developed ABL model significantly improves the predicted flow fields over both flat and complex terrain, when compared against neutral models and measurements....... cost than e.g. using large-eddy simulations. The developed ABL model is successfully validated using a range of different test cases with increasing complexity. Data from several large scale field campaigns, wind tunnel experiments, and previous numerical simulations is presented and compared against...

Why trace and delay conditioning are sometimes (but not always) hippocampal dependent: A computational model

Science.gov (United States)

Moustafa, Ahmed A.; Wufong, Ella; Servatius, Richard J.; Pang, Kevin C. H.; Gluck, Mark A.; Myers, Catherine E.

2013-01-01

A recurrent-network model provides a unified account of the hippocampal region in mediating the representation of temporal information in classical eyeblink conditioning. Much empirical research is consistent with a general conclusion that delay conditioning (in which the conditioned stimulus CS and unconditioned stimulus US overlap and co-terminate) is independent of the hippocampal system, while trace conditioning (in which the CS terminates before US onset) depends on the hippocampus. However, recent studies show that, under some circumstances, delay conditioning can be hippocampal-dependent and trace conditioning can be spared following hippocampal lesion. Here, we present an extension of our prior trial-level models of hippocampal function and stimulus representation that can explain these findings within a unified framework. Specifically, the current model includes adaptive recurrent collateral connections that aid in the representation of intra-trial temporal information. With this model, as in our prior models, we argue that the hippocampus is not specialized for conditioned response timing, but rather is a general-purpose system that learns to predict the next state of all stimuli given the current state of variables encoded by activity in recurrent collaterals. As such, the model correctly predicts that hippocampal involvement in classical conditioning should be critical not only when there is an intervening trace interval, but also when there is a long delay between CS onset and US onset. Our model simulates empirical data from many variants of classical conditioning, including delay and trace paradigms in which the length of the CS, the inter-stimulus interval, or the trace interval is varied. Finally, we discuss model limitations, future directions, and several novel empirical predictions of this temporal processing model of hippocampal function and learning. PMID:23178699

77 FR 32006 - Special Conditions: Gulfstream Model GVI Airplane; High Incidence Protection

Science.gov (United States)

2012-05-31

... Special Conditions No. 25-423-SC] Special Conditions: Gulfstream Model GVI Airplane; High Incidence... pertaining to a high incidence protection system that replaces the stall warning system during normal... the condition existing in the test or performance standard in which V SR is being used. (3) The weight...

77 FR 40255 - Special Conditions: Boeing, Model 737-800; Large Non-Structural Glass in the Passenger Compartment

Science.gov (United States)

2012-07-09

...: Glass partitions. Glass attached to the ceiling. Wall/door mounted mirrors/glass panels. Discussion The... monitor screens such as liquid crystal display (LCD) or plasma displays. These glass items may be...

77 FR 28533 - Special Conditions: Boeing, Model 737-800; Large Non-Structural Glass in the Passenger Compartment

Science.gov (United States)

2012-05-15

... following items: Glass partitions. Glass attached to the ceiling. Wall/door mounted mirrors/glass panels... indicator protective transparencies, or monitor screens such as liquid crystal display (LCD) or plasma...

78 FR 76731 - Special Conditions: Boeing Model 777-200, -300, and -300ER Series Airplanes; Rechargeable Lithium...

Science.gov (United States)

2013-12-19

... series airplanes have fly-by-wire controls, fully software-configurable avionics, and fiber-optic... Regulations (14 CFR) 25.1353, the FAA provided an airworthiness standard for lead acid batteries and nickel... maintenance characteristics that differ significantly from those of the nickel cadmium and lead acid...

78 FR 70848 - Special Conditions: Boeing Model 777-200, -300, and -300ER Series Airplanes; Aircraft Electronic...

Science.gov (United States)

2013-11-27

... Aerospace Company applied for a change to Type Certificate No. T00001SE Rev. 30 dated June 6, 2012 for... unintentional corruption of data and systems critical to the safety and maintenance of the airplane. The existing regulations and guidance material did not anticipate this type of system architecture or...

78 FR 70849 - Special Conditions: Boeing Model 777-200, -300, and -300ER Series Airplanes; Aircraft Electronic...

Science.gov (United States)

2013-11-27

... Aerospace Company applied for a change to Type Certificate No. T00001SE Rev. 30 dated June 6, 2012 for... unintentional corruption of data and systems critical to the safety and maintenance of the airplane. The existing regulations and guidance material did not anticipate this type of system architecture or...

76 FR 30523 - Special Conditions: Boeing Model 747-8/-8F Airplanes, Interaction of Systems and Structures

Science.gov (United States)

2011-05-26

... comments were received from one commenter. Concerns With the Philosophy of Controlling Aeroelastic... reservations with the philosophy of controlling an aeroelastic instability (flutter) with an active control... throughout the service life of the airplane by: (i) Analysis to the nominal aeroelastic stability envelope...

76 FR 14794 - Special Conditions: Boeing Model 747-8 Airplanes, Systems and Data Networks Security-Isolation or...

Science.gov (United States)

2011-03-18

... Networks Security--Isolation or Protection From Unauthorized Passenger Domain Systems Access AGENCY... systems and data networks. The applicable airworthiness regulations do not contain adequate or appropriate... connected networks. The network architecture would be used for a diverse set of functions, including: 1...

75 FR 71346 - Special Conditions: Boeing Model 787-8 Airplane; Lightning Protection of Fuel Tank Structure To...

Science.gov (United States)

2010-11-23

... this requirement would typically require a structured, quantitative safety analysis. Design areas that... objective is met by the proposed design using a structured system safety assessment similar to that... or are defined in Advisory Circular 25.1309- 1A, System Design and Analysis, dated June 21, 1988. The...

75 FR 76647 - Special Conditions: Boeing Model 747-8 Airplanes, Systems and Data Networks Security-Isolation or...

Science.gov (United States)

2010-12-09

...: Digital systems architecture composed of several connected networks. The proposed network architecture..., communication, and navigation systems (Aircraft Control Domain), 2. Airline business and administrative support... system architectures. Furthermore, 14 CFR regulations and current system safety assessment policy and...

Modeling of Cr(VI) Bioreduction Under Fermentative and Denitrifying Conditions

Science.gov (United States)

Molins, S.; Steefel, C.; Yang, L.; Beller, H. R.

2011-12-01

The mechanisms of bioreductive immobilization of Cr(VI) were investigated by reactive transport modeling of a set of flow-through column experiments performed using natural Hanford 100H aquifer sediment. The columns were continuously eluted with 5 μM Cr(VI), 5 mM lactate as the electron donor, and selected electron acceptors (tested individually). Here we focus on the two separate experimental conditions that showed the most removal of Cr(VI) from solution: fermentation and denitrification. In each case, a network of enzymatic and abiotic reaction pathways was considered to interpret the rate of chromate reduction. The model included biomass growth and decay, and thermodynamic limitations on reaction rates, and was constrained by effluent concentrations measured by IC and ICP-MS and additional information from bacterial isolates from column effluent. Under denitrifying conditions, Cr(VI) reduction was modeled as co-metabolic with nitrate reduction based on experimental observations and previous studies on a denitrifying bacterium derived from the Hanford 100H aquifer. The reactive transport model results supported this interpretation of the reaction mechanism and were used to quantify the efficiency of the process. The models results also suggest that biomass growth likely relied on a nitrogen source other than ammonium (e.g. nitrate). Under fermentative conditions and based on cell suspension studies performed on a bacterial isolate from the columns, the model assumes that Cr(VI) reduction is carried out directly by fermentative bacteria that convert lactate into acetate and propionate. The evolution to complete lactate fermentation and Cr(VI) reduction took place over a week's time and simulations were used to determine an estimate for a lower limit of the rate of chromate reduction by calibration with the flow-through column experimental results. In spite of sulfate being added to these columns, sulfate reduction proceeded at a slow rate and was not well

Modeling Macrosegregation in Directionally Solidified Aluminum Alloys under Gravitational and Microgravitational Conditions.

Energy Technology Data Exchange (ETDEWEB)

Lauer, Mark A.; Poirier, David R.; Erdmann, Robert G.; Tewari, Surendra N.; Madison, Jonathan D

2014-09-01

This report covers the modeling of seven directionally solidified samples, five under normal gravitational conditions and two in microgravity. A model is presented to predict macrosegregation during the melting phases of samples solidified under microgravitational conditions. The results of this model are compared against two samples processed in microgravity and good agreement is found. A second model is presented that captures thermosolutal convection during directional solidification. Results for this model are compared across several experiments and quantitative comparisons are made between the model and the experimentally obtained radial macrosegregation profiles with good agreement being found. Changes in cross section were present in some samples and micrographs of these are qualitatively compared with the results of the simulations. It is found that macrosegregation patterns can be affected by changing the mold material.

Asymmetries in conditional mean variance: modelling stock returns by asMA-asQGARCH

NARCIS (Netherlands)

de Gooijer, J.G.; Brännäs, K.

2004-01-01

We propose a nonlinear time series model where both the conditional mean and the conditional variance are asymmetric functions of past information. The model is particularly useful for analysing financial time series where it has been noted that there is an asymmetric impact of good news and bad

Numerical investigations of rib fracture failure models in different dynamic loading conditions.

Science.gov (United States)

Wang, Fang; Yang, Jikuang; Miller, Karol; Li, Guibing; Joldes, Grand R; Doyle, Barry; Wittek, Adam

2016-01-01

Rib fracture is one of the most common thoracic injuries in vehicle traffic accidents that can result in fatalities associated with seriously injured internal organs. A failure model is critical when modelling rib fracture to predict such injuries. Different rib failure models have been proposed in prediction of thorax injuries. However, the biofidelity of the fracture failure models when varying the loading conditions and the effects of a rib fracture failure model on prediction of thoracic injuries have been studied only to a limited extent. Therefore, this study aimed to investigate the effects of three rib failure models on prediction of thoracic injuries using a previously validated finite element model of the human thorax. The performance and biofidelity of each rib failure model were first evaluated by modelling rib responses to different loading conditions in two experimental configurations: (1) the three-point bending on the specimen taken from rib and (2) the anterior-posterior dynamic loading to an entire bony part of the rib. Furthermore, the simulation of the rib failure behaviour in the frontal impact to an entire thorax was conducted at varying velocities and the effects of the failure models were analysed with respect to the severity of rib cage damages. Simulation results demonstrated that the responses of the thorax model are similar to the general trends of the rib fracture responses reported in the experimental literature. However, they also indicated that the accuracy of the rib fracture prediction using a given failure model varies for different loading conditions.

Should tsunami models use a nonzero initial condition for horizontal velocity?

Science.gov (United States)

Nava, G.; Lotto, G. C.; Dunham, E. M.

2017-12-01

Tsunami propagation in the open ocean is most commonly modeled by solving the shallow water wave equations. These equations require two initial conditions: one on sea surface height and another on depth-averaged horizontal particle velocity or, equivalently, horizontal momentum. While most modelers assume that initial velocity is zero, Y.T. Song and collaborators have argued for nonzero initial velocity, claiming that horizontal displacement of a sloping seafloor imparts significant horizontal momentum to the ocean. They show examples in which this effect increases the resulting tsunami height by a factor of two or more relative to models in which initial velocity is zero. We test this claim with a "full-physics" integrated dynamic rupture and tsunami model that couples the elastic response of the Earth to the linearized acoustic-gravitational response of a compressible ocean with gravity; the model self-consistently accounts for seismic waves in the solid Earth, acoustic waves in the ocean, and tsunamis (with dispersion at short wavelengths). We run several full-physics simulations of subduction zone megathrust ruptures and tsunamis in geometries with a sloping seafloor, using both idealized structures and a more realistic Tohoku structure. Substantial horizontal momentum is imparted to the ocean, but almost all momentum is carried away in the form of ocean acoustic waves. We compare tsunami propagation in each full-physics simulation to that predicted by an equivalent shallow water wave simulation with varying assumptions regarding initial conditions. We find that the initial horizontal velocity conditions proposed by Song and collaborators consistently overestimate the tsunami amplitude and predict an inconsistent wave profile. Finally, we determine tsunami initial conditions that are rigorously consistent with our full-physics simulations by isolating the tsunami waves (from ocean acoustic and seismic waves) at some final time, and backpropagating the tsunami

On the identification of fractionally cointegrated VAR models with the F(d) condition

DEFF Research Database (Denmark)

Santucci de Magistris, Paolo; Carlini, Federico

for any choice of the lag-length when the true cointegration rank is known. The properties of these multiple non-identified models are studied and a necessary and sufficient condition for the identification of the fractional parameters of the system is provided. The condition is named F(d......). This is a generalization of the well-known I(1) condition to the fractional case. Imposing a proper restriction on the fractional integration parameter, d, is sufficient to guarantee identification of all model parameters and the validity of the F(d) condition. The paper also illustrates the indeterminacy between...

Boundary Conditions, Data Assimilation, and Predictability in Coastal Ocean Models

National Research Council Canada - National Science Library

Samelson, Roger M; Allen, John S; Egbert, Gary D; Kindle, John C; Snyder, Chris

2007-01-01

...: The specific objectives of this research are to determine the impact on coastal ocean circulation models of open ocean boundary conditions from Global Ocean Data Assimilation Experiment (GODAE...

Model of personal consumption under conditions of modern economy

Science.gov (United States)

Rakhmatullina, D. K.; Akhmetshina, E. R.; Ignatjeva, O. A.

2017-12-01

In the conditions of the modern economy, in connection with the development of production, the expansion of the market for goods and services, its differentiation, active use of marketing tools in the sphere of sales, changes occur in the system of values and consumer needs. Motives that drive the consumer are transformed, stimulating it to activity. The article presents a model of personal consumption that takes into account modern trends in consumer behavior. The consumer, making a choice, seeks to maximize the overall utility from consumption, physiological and socio-psychological satisfaction, in accordance with his expectations, preferences and conditions of consumption. The system of his preferences is formed under the influence of factors of a different nature. It is also shown that the structure of consumer spending allows us to characterize and predict its further behavior in the market. Based on the proposed model and analysis of current trends in consumer behavior, conclusions and recommendations have been made that can be used by legislative and executive government bodies, business organizations, research centres and other structures to form a methodological and analytical tool for preparing a forecast model of consumption.

Photovoltaic Array Condition Monitoring Based on Online Regression of Performance Model

DEFF Research Database (Denmark)

Spataru, Sergiu; Sera, Dezso; Kerekes, Tamas

2013-01-01

regression modeling, from PV array production, plane-of-array irradiance, and module temperature measurements, acquired during an initial learning phase of the system. After the model has been parameterized automatically, the condition monitoring system enters the normal operation phase, where...

Wall conditioning for ITER: Current experimental and modeling activities

Energy Technology Data Exchange (ETDEWEB)

Douai, D., E-mail: david.douai@cea.fr [CEA, IRFM, Association Euratom-CEA, 13108 St. Paul lez Durance (France); Kogut, D. [CEA, IRFM, Association Euratom-CEA, 13108 St. Paul lez Durance (France); Wauters, T. [LPP-ERM/KMS, Association Belgian State, 1000 Brussels (Belgium); Brezinsek, S. [FZJ, Institut für Energie- und Klimaforschung Plasmaphysik, 52441 Jülich (Germany); Hagelaar, G.J.M. [Laboratoire Plasma et Conversion d’Energie, UMR5213, Toulouse (France); Hong, S.H. [National Fusion Research Institute, Daejeon 305-806 (Korea, Republic of); Lomas, P.J. [CCFE, Culham Science Centre, OX14 3DB Abingdon (United Kingdom); Lyssoivan, A. [LPP-ERM/KMS, Association Belgian State, 1000 Brussels (Belgium); Nunes, I. [Associação EURATOM-IST, Instituto de Plasmas e Fusão Nuclear, 1049-001 Lisboa (Portugal); Pitts, R.A. [ITER International Organization, F-13067 St. Paul lez Durance (France); Rohde, V. [Max-Planck-Institut für Plasmaphysik, 85748 Garching (Germany); Vries, P.C. de [ITER International Organization, F-13067 St. Paul lez Durance (France)

2015-08-15

Wall conditioning will be required in ITER to control fuel and impurity recycling, as well as tritium (T) inventory. Analysis of conditioning cycle on the JET, with its ITER-Like Wall is presented, evidencing reduced need for wall cleaning in ITER compared to JET–CFC. Using a novel 2D multi-fluid model, current density during Glow Discharge Conditioning (GDC) on the in-vessel plasma-facing components (PFC) of ITER is predicted to approach the simple expectation of total anode current divided by wall surface area. Baking of the divertor to 350 °C should desorb the majority of the co-deposited T. ITER foresees the use of low temperature plasma based techniques compatible with the permanent toroidal magnetic field, such as Ion (ICWC) or Electron Cyclotron Wall Conditioning (ECWC), for tritium removal between ITER plasma pulses. Extrapolation of JET ICWC results to ITER indicates removal comparable to estimated T-retention in nominal ITER D:T shots, whereas GDC may be unattractive for that purpose.

Theoretical Background for the Decision-Making Process Modelling under Controlled Intervention Conditions

Directory of Open Access Journals (Sweden)

Bakanauskienė Irena

2017-12-01

Full Text Available This article is intended to theoretically justify the decision-making process model for the cases, when active participation of investing entities in controlling the activities of an organisation and their results is noticeable. Based on scientific literature analysis, a concept of controlled conditions is formulated, and using a rational approach to the decision-making process, a model of the 11-steps decision-making process under controlled intervention is presented. Also, there have been unified conditions, describing the case of controlled interventions thus providing preconditions to ensure the adequacy of the proposed decision-making process model.

Reductions in biomarkers of exposure (BoE) to harmful or potentially harmful constituents (HPHCs) following partial or complete substitution of cigarettes with electronic cigarettes in adult smokers.

Science.gov (United States)

O'Connell, Grant; Graff, Donald W; D'Ruiz, Carl D

2016-07-01

Changes in fifteen urine, blood and exhaled breath BoEs of HPHCs representing classes of compounds reported by FDA to be significant contributors to smoking-associated disease risks were measured in 105 clinical-confined subjects following randomization and a five-day forced-switch from usual brand conventional combustible cigarettes to: (i) exclusive commercial e-cigarette use; (ii) dual-use of commercial e-cigarettes and the subject's usual cigarette brand; or (iii) discontinued use of all tobacco or nicotine products. Levels of urinary biomarkers in subjects that completely substituted their usual cigarette with e-cigarettes were significantly lower (29-95%) after 5 days. Percent reductions in eight of nine urinary BoEs were indistinguishable to smokers who had quit smoking, except for nicotine equivalents, which declined by 25-40%. Dual users who halved self-reported daily cigarette consumption with e-cigarettes exhibited reductions (7-38%) in eight of nine urinary biomarkers, but had increase (1-20%) in nicotine equivalents. Reductions were broadly proportional to the reduced numbers of cigarettes smoked. Dual user urinary nicotine equivalents were slightly higher, but not statistically significant. After 5 days, blood nicotine biomarker levels were lower in the cessation (75-96%) and exclusive use groups (11-83%); with dual users experiencing no significant reductions. All subjects experienced significant decreases in exhaled CO. Decreases in the cessation and exclusive groups ranged from 88-89% and 27-32% in dual users. Exhaled NO increased in the cessation and exclusive groups (46-63% respectively), whereas the dual users experienced minimal changes. Overall, smokers who completely or partially substituted conventional cigarettes with e-cigarettes over five days, experienced reductions in HPHCs.

Using fuzzy rule-based knowledge model for optimum plating conditions search

Science.gov (United States)

Solovjev, D. S.; Solovjeva, I. A.; Litovka, Yu V.; Arzamastsev, A. A.; Glazkov, V. P.; L’vov, A. A.

2018-03-01

The paper discusses existing approaches to plating process modeling in order to decrease the distribution thickness of plating surface cover. However, these approaches do not take into account the experience, knowledge, and intuition of the decision-makers when searching the optimal conditions of electroplating technological process. The original approach to optimal conditions search for applying the electroplating coatings, which uses the rule-based model of knowledge and allows one to reduce the uneven product thickness distribution, is proposed. The block diagrams of a conventional control system of a galvanic process as well as the system based on the production model of knowledge are considered. It is shown that the fuzzy production model of knowledge in the control system makes it possible to obtain galvanic coatings of a given thickness unevenness with a high degree of adequacy to the experimental data. The described experimental results confirm the theoretical conclusions.

Conditional Monte Carlo randomization tests for regression models.

Science.gov (United States)

Parhat, Parwen; Rosenberger, William F; Diao, Guoqing

2014-08-15

We discuss the computation of randomization tests for clinical trials of two treatments when the primary outcome is based on a regression model. We begin by revisiting the seminal paper of Gail, Tan, and Piantadosi (1988), and then describe a method based on Monte Carlo generation of randomization sequences. The tests based on this Monte Carlo procedure are design based, in that they incorporate the particular randomization procedure used. We discuss permuted block designs, complete randomization, and biased coin designs. We also use a new technique by Plamadeala and Rosenberger (2012) for simple computation of conditional randomization tests. Like Gail, Tan, and Piantadosi, we focus on residuals from generalized linear models and martingale residuals from survival models. Such techniques do not apply to longitudinal data analysis, and we introduce a method for computation of randomization tests based on the predicted rate of change from a generalized linear mixed model when outcomes are longitudinal. We show, by simulation, that these randomization tests preserve the size and power well under model misspecification. Copyright © 2014 John Wiley & Sons, Ltd.

Groundwater flow modelling of periods with periglacial and glacial climate conditions - Laxemar

Energy Technology Data Exchange (ETDEWEB)

Vidstrand, Patrik (TerraSolve AB, Floda (Sweden)); Rhen, Ingvar (SWECO Environment AB, Falun (Sweden)); Zugec, Nada (Bergab, Goeteborg (Sweden))

2010-12-15

As a part of the license application for a final repository for spent nuclear fuel at Forsmark, the Swedish Nuclear Fuel and Waste Management Company (SKB) has undertaken a series of groundwater flow modelling studies. These represent time periods with different hydraulic conditions and the simulations carried out contribute to the overall evaluation of the repository design and long-term radiological safety. This report is concerned with the modelling of a repository at the Laxemar-Simpevarp site during periglacial and glacial climate conditions as a comparison to corresponding modelling carried out for Forsmark /Vidstrand et al. 2010/. The groundwater flow modelling study reported here comprises a coupled thermal-hydraulic-chemical (T-H-C) analysis of periods with periglacial and glacial climate conditions. The objective of the report is to provide bounding hydrogeological estimates at different stages during glaciation and deglaciation of a glacial cycle at Laxemar. Three cases with different climate conditions are analysed here: (i) Temperate case, (ii) Glacial case without permafrost, and (iii) Glacial case with permafrost. The glacial periods are transient and encompass approximately 13,000 years. The simulation results comprise pressures, Darcy fluxes, and water salinities, as well as advective transport performance measures obtained by particle tracking such as flow path lengths, travel times and flow-related transport resistances. The modelling is accompanied by a sensitivity study that addresses the impact of the following matters: the direction of the ice sheet advance and the bedrock hydraulic and transport properties

New boundary conditions for 3D RF modelling

International Nuclear Information System (INIS)

Ko, K.; Nelson, E.; Fitze, H.

1990-01-01

The new capabilities are being implemented into the 3D particle-in-cell code, ARGUS, which will reduce substantially both problem size and computing time when modeling realistic geometries with high accuracies. In the time domain, a cylindrical radiative boundary condition will enable traveling wave propagation to be simulated in accelerator structures. An application of interest is the input coupler in the SLAC x-band high-gradient structure where local field gradients and impedance matching are important issues. In the frequency domain, a quasi-periodic boundary condition will facilitate the cold-test analysis of 3D periodic structures where many calculations are required to generate an ω β diagram. Present applications include the crossed-field amplifier cavity and the cluster klystron cavity

On the identification of fractionally cointegrated VAR models with the F(d) condition

DEFF Research Database (Denmark)

Carlini, Federico; Santucci de Magistris, Paolo

for any choice of the lag length, also when the true cointegration rank is known. The properties of these multiple non-identified models are studied and a necessary and sufficient condition for the identification of the fractional parameters of the system is provided. The condition is named F(d......) and it is a generalization to the fractional case of the I(1) condition in the VECM model. The assessment of the F(d) condition in the empirical analysis is relevant for the determination of the fractional parameters as well as the number of lags. The paper also illustrates the indeterminacy between the cointegration rank...

Extension of the PMV model to non-air-conditioned building in warm climates

DEFF Research Database (Denmark)

Fanger, Povl Ole; Toftum, Jørn

2002-01-01

The PMV model agrees well with high-quality field studies in buildings with HVAC systems, situated in cold, temperate and warm climates, studied during both summer and winter. In non-air-conditioned buildings in warm climates, occupants may sense the warmth as being less severe than the PMV...... predicts. The main reason is low expectations, but a metabolic rate that is estimated too high can also contribute to explaining the difference. An extension of the PMV model that includes an expectancy factor is introduced for use in non-air-conditioned buildings in warm climates. The extended PMV model...... agrees well with quality field studies in non-air-conditioned buildings of three continents....

Economic value added model upon conditions of banking company

Directory of Open Access Journals (Sweden)

Vlasta Kašparovská

2008-01-01

Full Text Available The content of this article is the application of the economic value added model (EVA upon the conditions of a banking company. Due to the character of banking business, which is in a different structure of financial sheet, it is not possible to use the standard model EVA for this banking company. The base of this article is the outlined of basic principles of the EVA mode in a non-banking company. Basic specified banking activity dissimilarities are analysed and a directed methodology adjustment of a model such as this, so that it is possible to use it for a banking company.

Unmanned Bomber: The Effects It Will Bring to the Nuclear Triad

Science.gov (United States)

2014-06-01

New York, NY: Avery Trade, 2011), 41. 16 Boeing, History of B-2 Spirit , http://www.boeing.com/boeing/history/boeing/ b2 .page retrieved on January...factsheets/start1 retrieved on February 23, 2014 Boeing, History of B-2 Spirit , http://www.boeing.com/boeing/history/boeing/ b2 .page retrieved on

A thermal model for photovoltaic panels under varying atmospheric conditions

International Nuclear Information System (INIS)

Armstrong, S.; Hurley, W.G.

2010-01-01

The response of the photovoltaic (PV) panel temperature is dynamic with respect to the changes in the incoming solar radiation. During periods of rapidly changing conditions, a steady state model of the operating temperature cannot be justified because the response time of the PV panel temperature becomes significant due to its large thermal mass. Therefore, it is of interest to determine the thermal response time of the PV panel. Previous attempts to determine the thermal response time have used indoor measurements, controlling the wind flow over the surface of the panel with fans or conducting the experiments in darkness to avoid radiative heat loss effects. In real operating conditions, the effective PV panel temperature is subjected to randomly varying ambient temperature and fluctuating wind speeds and directions; parameters that are not replicated in controlled, indoor experiments. A new thermal model is proposed that incorporates atmospheric conditions; effects of PV panel material composition and mounting structure. Experimental results are presented which verify the thermal behaviour of a photovoltaic panel for low to strong winds.

Rate Theory Modeling and Simulations of Silicide Fuel at LWR Conditions

Energy Technology Data Exchange (ETDEWEB)

Miao, Yinbin [Argonne National Lab. (ANL), Argonne, IL (United States); Ye, Bei [Argonne National Lab. (ANL), Argonne, IL (United States); Mei, Zhigang [Argonne National Lab. (ANL), Argonne, IL (United States); Hofman, Gerard [Argonne National Lab. (ANL), Argonne, IL (United States); Yacout, Abdellatif [Argonne National Lab. (ANL), Argonne, IL (United States)

2015-12-10

Uranium silicide (U₃Si₂) fuel has higher thermal conductivity and higher uranium density, making it a promising candidate for the accident-tolerant fuel (ATF) used in light water reactors (LWRs). However, previous studies on the fuel performance of U₃Si₂, including both experimental and computational approaches, have been focusing on the irradiation conditions in research reactors, which usually involve low operation temperatures and high fuel burnups. Thus, it is important to examine the fuel performance of U₃Si₂ at typical LWR conditions so as to evaluate the feasibility of replacing conventional uranium dioxide fuel with this silicide fuel material. As in-reactor irradiation experiments involve significant time and financial cost, it is appropriate to utilize modeling tools to estimate the behavior of U₃Si₂ in LWRs based on all those available research reactor experimental references and state-of-the-art density functional theory (DFT) calculation capabilities at the early development stage. Hence, in this report, a comprehensive investigation of the fission gas swelling behavior of U₃Si₂ at LWR conditions is introduced. The modeling efforts mentioned in this report was based on the rate theory (RT) model of fission gas bubble evolution that has been successfully applied for a variety of fuel materials at devious reactor conditions. Both existing experimental data and DFT-calculated results were used for the optimization of the parameters adopted by the RT model. Meanwhile, the fuel-cladding interaction was captured by the coupling of the RT model with simplified mechanical correlations. Therefore, the swelling behavior of U₃Si₂ fuel and its consequent interaction with cladding in LWRs was predicted by the rate theory modeling, providing valuable information for the development of U₃Si₂ fuel as an accident

Assessing uncertainties in global cropland futures using a conditional probabilistic modelling framework

NARCIS (Netherlands)

Engström, Kerstin; Olin, Stefan; Rounsevell, Mark D A; Brogaard, Sara; Van Vuuren, Detlef P.; Alexander, Peter; Murray-Rust, Dave; Arneth, Almut

2016-01-01

We present a modelling framework to simulate probabilistic futures of global cropland areas that are conditional on the SSP (shared socio-economic pathway) scenarios. Simulations are based on the Parsimonious Land Use Model (PLUM) linked with the global dynamic vegetation model LPJ-GUESS

A model of amygdala-hippocampal-prefrontal interaction in fear conditioning and extinction in animals

Science.gov (United States)

Moustafa, Ahmed A.; Gilbertson, Mark W.; Orr, Scott P.; Herzallah, Mohammad M.; Servatius, Richard. J.; Myers, Catherine E.

2012-01-01

Empirical research has shown that the amygdala, hippocampus, and ventromedial prefrontal cortex (vmPFC) are involved in fear conditioning. However, the functional contribution of each brain area and the nature of their interactions are not clearly understood. Here, we extend existing neural network models of the functional roles of the hippocampus in classical conditioning to include interactions with the amygdala and prefrontal cortex. We apply the model to fear conditioning, in which animals learn physiological (e.g. heart rate) and behavioral (e.g. freezing) responses to stimuli that have been paired with a highly aversive event (e.g. electrical shock). The key feature of our model is that learning of these conditioned responses in the central nucleus of the amygdala is modulated by two separate processes, one from basolateral amygdala and signaling a positive prediction error, and one from the vmPFC, via the intercalated cells of the amygdala, and signaling a negative prediction error. In addition, we propose that hippocampal input to both vmPFC and basolateral amygdala is essential for contextual modulation of fear acquisition and extinction. The model is sufficient to account for a body of data from various animal fear conditioning paradigms, including acquisition, extinction, reacquisition, and context specificity effects. Consistent with studies on lesioned animals, our model shows that damage to the vmPFC impairs extinction, while damage to the hippocampus impairs extinction in a different context (e.g., a different conditioning chamber from that used in initial training in animal experiments). We also discuss model limitations and predictions, including the effects of number of training trials on fear conditioning. PMID:23164732

Evaluation of two transport aircraft and several ground test vehicle friction measurements obtained for various runway surface types and conditions. A summary of test results from joint FAA/NASA Runway Friction Program

Science.gov (United States)

Yager, Thomas J.; Vogler, William A.; Baldasare, Paul

1990-01-01

Tests with specially instrumented NASA Boeing 737 and 727 aircraft together with several different ground friction measuring devices were conducted for a variety of runway surface types and conditions. These tests are part of joint FAA/NASA Aircraft/Ground Vehicle Runway Friction Program aimed at obtaining a better understanding of aircraft ground handling performance under adverse weather conditions and defining relationships between aircraft and ground vehicle tire friction measurements. Aircraft braking performance on dry, wet, snow and ice-covered runway conditions is discussed as well as ground vehicle friction data obtained under similar runway conditions. For a given contaminated runway surface condition, the correlation between ground vehicles and aircraft friction data is identified. The influence of major test parameters on friction measurements such as speed, test tire characteristics, type and amount of surface contaminant, and ambient temperature are discussed. The effect of surface type on wet friction levels is also evaluated from comparative data collected on grooved and ungrooved concrete and asphalt surfaces.

Markov-switching model for nonstationary runoff conditioned on El Nino information

DEFF Research Database (Denmark)

Gelati, Emiliano; Madsen, H.; Rosbjerg, Dan

2010-01-01

We define a Markov-modulated autoregressive model with exogenous input (MARX) to generate runoff scenarios using climatic information. Runoff parameterization is assumed to be conditioned on a hidden climate state following a Markov chain, where state transition probabilities are functions...... of the climatic input. MARX allows stochastic modeling of nonstationary runoff, as runoff anomalies are described by a mixture of autoregressive models with exogenous input, each one corresponding to a climate state. We apply MARX to inflow time series of the Daule Peripa reservoir (Ecuador). El Nino Southern...... Oscillation (ENSO) information is used to condition runoff parameterization. Among the investigated ENSO indexes, the NINO 1+2 sea surface temperature anomalies and the trans-Nino index perform best as predictors. In the perspective of reservoir optimization at various time scales, MARX produces realistic...

Physical plausibility of cold star models satisfying Karmarkar conditions

Energy Technology Data Exchange (ETDEWEB)

Fuloria, Pratibha [Kumaun University, Physics Dept., Almora (India); Pant, Neeraj [N.D.A., Maths Dept., Khadakwasla, Pune (India)

2017-11-15

In the present article, we have obtained a new well behaved solution to Einstein's field equations in the background of Karmarkar spacetime. The solution has been used for stellar modelling within the demand of current observational evidences. All the physical parameters are well behaved inside the stellar interior and our model satisfies all the required conditions to be physically realizable. The obtained compactness parameter is within the Buchdahl limit, i.e. 2M/R ≤ 8/9. The TOV equation is well maintained inside the fluid spheres. The stability of the models has been further confirmed by using Herrera's cracking method. The models proposed in the present work are compatible with observational data of compact objects 4U1608-52 and PSRJ1903+327. The necessary graphs have been shown to authenticate the physical viability of our models. (orig.)

Physical plausibility of cold star models satisfying Karmarkar conditions

International Nuclear Information System (INIS)

Fuloria, Pratibha; Pant, Neeraj

2017-01-01

In the present article, we have obtained a new well behaved solution to Einstein's field equations in the background of Karmarkar spacetime. The solution has been used for stellar modelling within the demand of current observational evidences. All the physical parameters are well behaved inside the stellar interior and our model satisfies all the required conditions to be physically realizable. The obtained compactness parameter is within the Buchdahl limit, i.e. 2M/R ≤ 8/9. The TOV equation is well maintained inside the fluid spheres. The stability of the models has been further confirmed by using Herrera's cracking method. The models proposed in the present work are compatible with observational data of compact objects 4U1608-52 and PSRJ1903+327. The necessary graphs have been shown to authenticate the physical viability of our models. (orig.)

Physical plausibility of cold star models satisfying Karmarkar conditions

Science.gov (United States)

Fuloria, Pratibha; Pant, Neeraj

2017-11-01

In the present article, we have obtained a new well behaved solution to Einstein's field equations in the background of Karmarkar spacetime. The solution has been used for stellar modelling within the demand of current observational evidences. All the physical parameters are well behaved inside the stellar interior and our model satisfies all the required conditions to be physically realizable. The obtained compactness parameter is within the Buchdahl limit, i.e. 2M/R ≤ 8/9 . The TOV equation is well maintained inside the fluid spheres. The stability of the models has been further confirmed by using Herrera's cracking method. The models proposed in the present work are compatible with observational data of compact objects 4U1608-52 and PSRJ1903+327. The necessary graphs have been shown to authenticate the physical viability of our models.

Model development to evaluate evolution of redox conditions in the near field

International Nuclear Information System (INIS)

Chiba, Tamotsu; Miki, Takahito; Inagaki, Manabu; Sasamoto, Hiroshi; Yui, Mikazu

1999-02-01

Deep underground is thought to be a potential place for high level radioactive waste repository. It is believed that the chemical condition of deep groundwater is generally anoxic and reducing. However, during construction and operation phase of repository, oxygen will diffuse some distance into the surrounding rock mass, and diffused oxygen may remain in the surrounding rock mass even after repository closure. In such a case, the transitional redox condition around the drift is not preferable in view point of safety assessment for HLW disposal. Hence, it is very important to evaluate evolution of redox conditions in the near field. This report describes the status of model development to evaluate evolution of redox conditions in the near field. We use the commercial solver to equate the mathematical equations which mean evolution of redox condition in the near field. The target area modeled in this report are near field rock mass and engineered barrier (buffer). In case of near field rock mass, we consider the following two geological media: (1) porous media for sedimentary rock, (2) fractured media for crystalline rock. In case of the engineered barrier, we regard the buffer as porous media. We simulate the behavior of dissolved oxygen and Fe 2+ in groundwater during evolution of redox condition in the near field rock mass and the buffer. In case of the porous media, we consider diffusion of chemical species as dominant transport mechanism. On the other hand, in case of the fractured media, we consider diffusion of chemical species in rock matrix and advection of that (only dissolved oxygen considered in this model) in fracture as transport mechanism. We also use the rate law of iron oxidation reaction and dissolution of Fe-bearing minerals in this model besides. (author)

Lumped-parameter modeling of PWR downcomer and pressurizer for LOCA conditions

International Nuclear Information System (INIS)

Rohatgi, U.S.; Saha, P.; Dubow, A.A.

1978-01-01

Two lumped-parameter models, one for a PWR downcomer and the other for a pressurizer, are presented. The models are based on the transient, nonhomogeneous, drift-flux description of two-phase flow, and are suitable for simulating a hypothetical LOCA condition. Effects of thermal nonequilibrium are incorporated in the downcomer model, whereas the pressurizer model can track the interfaces among various flow regimes. Semiimplicit numerical schemes are used for solution. Encouraging results have been obtained for both the models. (author)

Determination of modeling parameters for power IGBTs under pulsed power conditions

Energy Technology Data Exchange (ETDEWEB)

Dale, Gregory E [Los Alamos National Laboratory; Van Gordon, Jim A [U. OF MISSOURI; Kovaleski, Scott D [U. OF MISSOURI

2010-01-01

While the power insulated gate bipolar transistor (IGRT) is used in many applications, it is not well characterized under pulsed power conditions. This makes the IGBT difficult to model for solid state pulsed power applications. The Oziemkiewicz implementation of the Hefner model is utilized to simulate IGBTs in some circuit simulation software packages. However, the seventeen parameters necessary for the Oziemkiewicz implementation must be known for the conditions under which the device will be operating. Using both experimental and simulated data with a least squares curve fitting technique, the parameters necessary to model a given IGBT can be determined. This paper presents two sets of these seventeen parameters that correspond to two different models of power IGBTs. Specifically, these parameters correspond to voltages up to 3.5 kV, currents up to 750 A, and pulse widths up to 10 {micro}s. Additionally, comparisons of the experimental and simulated data will be presented.

Sliding mode fault tolerant control dealing with modeling uncertainties and actuator faults.

Science.gov (United States)

Wang, Tao; Xie, Wenfang; Zhang, Youmin

2012-05-01

In this paper, two sliding mode control algorithms are developed for nonlinear systems with both modeling uncertainties and actuator faults. The first algorithm is developed under an assumption that the uncertainty bounds are known. Different design parameters are utilized to deal with modeling uncertainties and actuator faults, respectively. The second algorithm is an adaptive version of the first one, which is developed to accommodate uncertainties and faults without utilizing exact bounds information. The stability of the overall control systems is proved by using a Lyapunov function. The effectiveness of the developed algorithms have been verified on a nonlinear longitudinal model of Boeing 747-100/200. Copyright © 2012 ISA. Published by Elsevier Ltd. All rights reserved.

Aerothermal Ground Testing of Flexible Thermal Protection Systems for Hypersonic Inflatable Aerodynamic Decelerators

Science.gov (United States)

Bruce, Walter E., III; Mesick, Nathaniel J.; Ferlemann, Paul G.; Siemers, Paul M., III; DelCorso, Joseph A.; Hughes, Stephen J.; Tobin, Steven A.; Kardell, Matthew P.

2012-01-01

Flexible TPS development involves ground testing and analysis necessary to characterize performance of the FTPS candidates prior to flight testing. This paper provides an overview of the analysis and ground testing efforts performed over the last year at the NASA Langley Research Center and in the Boeing Large-Core Arc Tunnel (LCAT). In the LCAT test series, material layups were subjected to aerothermal loads commensurate with peak re-entry conditions enveloping a range of HIAD mission trajectories. The FTPS layups were tested over a heat flux range from 20 to 50 W/cm with associated surface pressures of 3 to 8 kPa. To support the testing effort a significant redesign of the existing shear (wedge) model holder from previous testing efforts was undertaken to develop a new test technique for supporting and evaluating the FTPS in the high-temperature, arc jet flow. Since the FTPS test samples typically experience a geometry change during testing, computational fluid dynamic (CFD) models of the arc jet flow field and test model were developed to support the testing effort. The CFD results were used to help determine the test conditions experienced by the test samples as the surface geometry changes. This paper includes an overview of the Boeing LCAT facility, the general approach for testing FTPS, CFD analysis methodology and results, model holder design and test methodology, and selected thermal results of several FTPS layups.

Explicit treatment for Dirichlet, Neumann and Cauchy boundary conditions in POD-based reduction of groundwater models

Science.gov (United States)

Gosses, Moritz; Nowak, Wolfgang; Wöhling, Thomas

2018-05-01

In recent years, proper orthogonal decomposition (POD) has become a popular model reduction method in the field of groundwater modeling. It is used to mitigate the problem of long run times that are often associated with physically-based modeling of natural systems, especially for parameter estimation and uncertainty analysis. POD-based techniques reproduce groundwater head fields sufficiently accurate for a variety of applications. However, no study has investigated how POD techniques affect the accuracy of different boundary conditions found in groundwater models. We show that the current treatment of boundary conditions in POD causes inaccuracies for these boundaries in the reduced models. We provide an improved method that splits the POD projection space into a subspace orthogonal to the boundary conditions and a separate subspace that enforces the boundary conditions. To test the method for Dirichlet, Neumann and Cauchy boundary conditions, four simple transient 1D-groundwater models, as well as a more complex 3D model, are set up and reduced both by standard POD and POD with the new extension. We show that, in contrast to standard POD, the new method satisfies both Dirichlet and Neumann boundary conditions. It can also be applied to Cauchy boundaries, where the flux error of standard POD is reduced by its head-independent contribution. The extension essentially shifts the focus of the projection towards the boundary conditions. Therefore, we see a slight trade-off between errors at model boundaries and overall accuracy of the reduced model. The proposed POD extension is recommended where exact treatment of boundary conditions is required.

Developed Hybrid Model for Propylene Polymerisation at Optimum Reaction Conditions

Directory of Open Access Journals (Sweden)

Mohammad Jakir Hossain Khan

2016-02-01

Full Text Available A statistical model combined with CFD (computational fluid dynamic method was used to explain the detailed phenomena of the process parameters, and a series of experiments were carried out for propylene polymerisation by varying the feed gas composition, reaction initiation temperature, and system pressure, in a fluidised bed catalytic reactor. The propylene polymerisation rate per pass was considered the response to the analysis. Response surface methodology (RSM, with a full factorial central composite experimental design, was applied to develop the model. In this study, analysis of variance (ANOVA indicated an acceptable value for the coefficient of determination and a suitable estimation of a second-order regression model. For better justification, results were also described through a three-dimensional (3D response surface and a related two-dimensional (2D contour plot. These 3D and 2D response analyses provided significant and easy to understand findings on the effect of all the considered process variables on expected findings. To diagnose the model adequacy, the mathematical relationship between the process variables and the extent of polymer conversion was established through the combination of CFD with statistical tools. All the tests showed that the model is an excellent fit with the experimental validation. The maximum extent of polymer conversion per pass was 5.98% at the set time period and with consistent catalyst and co-catalyst feed rates. The optimum conditions for maximum polymerisation was found at reaction temperature (RT 75 °C, system pressure (SP 25 bar, and 75% monomer concentration (MC. The hydrogen percentage was kept fixed at all times. The coefficient of correlation for reaction temperature, system pressure, and monomer concentration ratio, was found to be 0.932. Thus, the experimental results and model predicted values were a reliable fit at optimum process conditions. Detailed and adaptable CFD results were capable

Mathematical modelling of unglazed solar collectors under extreme operating conditions

DEFF Research Database (Denmark)

Bunea, M.; Perers, Bengt; Eicher, S.

2015-01-01

average temperature levels at the evaporator. Simulation of these systems requires a collector model that can take into account operation at very low temperatures (below freezing) and under various weather conditions, particularly operation without solar irradiation.A solar collector mathematical model......Combined heat pumps and solar collectors got a renewed interest on the heating system market worldwide. Connected to the heat pump evaporator, unglazed solar collectors can considerably increase their efficiency, but they also raise the coefficient of performance of the heat pump with higher...... was found due to the condensation phenomenon and up to 40% due to frost under no solar irradiation. This work also points out the influence of the operating conditions on the collector's characteristics.Based on experiments carried out at a test facility, every heat flux on the absorber was separately...

Modeling real conditions of 'Ukrytie' object in 3D measurement

International Nuclear Information System (INIS)

Podbereznyj, S.S.

2001-01-01

The article covers a technology of creation on soft products basis for designing: AutoCad, and computer graphics and animation 3D Studio, 3DS MAX, of 3D model of geometrical parameters of current conditions of building structures, technological equipment, fuel-containing materials, concrete, water of ruined Unit 4, 'Ukryttia' object, of Chernobyl NPP. The model built using the above technology will be applied in the future as a basis when automating the design and computer modeling of processes at the 'Ukryttia' object

76 FR 41041 - Special Conditions: Gulfstream Aerospace LP (GALP) Model G250 Airplane, Interaction of Systems...

Science.gov (United States)

2011-07-13

... Conditions No. 25-439-SC] Special Conditions: Gulfstream Aerospace LP (GALP) Model G250 Airplane, Interaction... special conditions are issued for the Gulfstream Aerospace LP (GALP) Model G250 airplane. This airplane...

Modeling current climate conditions for forest pest risk assessment

Science.gov (United States)

Frank H. Koch; John W. Coulston

2010-01-01

Current information on broad-scale climatic conditions is essential for assessing potential distribution of forest pests. At present, sophisticated spatial interpolation approaches such as the Parameter-elevation Regressions on Independent Slopes Model (PRISM) are used to create high-resolution climatic data sets. Unfortunately, these data sets are based on 30-year...

Model predictions and control of conditions in a CA-reefer container

NARCIS (Netherlands)

Sman, van der R.G.M.; Verdijck, G.J.C.

2003-01-01

In this paper a concept for energy saving for refrigerated container transport is presented. The concept is based on model-predictive control of the set points of the cooling unit. These models predict energy consumption of the cooling unit, climatic conditions inside the cargo space, and the change

Creation of integrated information model of 'Ukryttia' object premises condition to support the works

International Nuclear Information System (INIS)

Postil, S.D.; Ermolenko, A.I.; Ivanov, V.V.; Kotlyarov, V.T.

2002-01-01

A technology for creation of integrated information model of 'Ukryttia' Object premises conditions was developed on the basis of geoinformation system AutoCad. DB Access and instrumental utility 3D MAX. Information models and database for conditions of 'Ukryttia' object's premises located between 0.000 and 67.000 marks in axes 41-52, row G-T, were created. Using integrated information model of 'Ukryttia' object premises conditions, 3D surface distribution of radiation field in the object premises on level 0.000 has been received. It is revealed that maximum values of radiation field are concentrated over the clusters of fuel-containing materials

Kinetic modeling of growth and lipid body induction in Chlorella pyrenoidosa under heterotrophic conditions.

Science.gov (United States)

Sachdeva, Neha; Kumar, G Dinesh; Gupta, Ravi Prakash; Mathur, Anshu Shankar; Manikandan, B; Basu, Biswajit; Tuli, Deepak Kumar

2016-10-01

The aim of the present work was to develop a mathematical model to describe the biomass and (total) lipid productivity of Chlorella pyrenoidosa NCIM 2738 under heterotrophic conditions. Biomass growth rate was predicted by Droop's cell quota model, while changes observed in cell quota (utilization) under carbon excess conditions were used for the modeling and predicting the lipid accumulation rate. The model was simulated under non-limiting (excess) carbon and limiting nitrate concentration and validated with experimental data for the culture grown in batch (flask) mode under different nitrate concentrations. The present model incorporated two modes (growth and stressed) for the prediction of endogenous lipid synthesis/induction and aimed to predict the effect and response of the microalgae under nutrient starvation (stressed) conditions. MATLAB and Genetic Algorithm were employed for the prediction and validation of the model parameters. Copyright © 2016 Elsevier Ltd. All rights reserved.

MODELING THE AMBIENT CONDITION EFFECTS OF AN AIR-COOLED NATURAL CIRCULATION SYSTEM

Energy Technology Data Exchange (ETDEWEB)

Hu, Rui; Lisowski, Darius D.; Bucknor, Matthew; Kraus, Adam R.; Lv, Qiuping

2017-07-02

The Reactor Cavity Cooling System (RCCS) is a passive safety concept under consideration for the overall safety strategy of advanced reactors such as the High Temperature Gas-Cooled Reactor (HTGR). One such variant, air-cooled RCCS, uses natural convection to drive the flow of air from outside the reactor building to remove decay heat during normal operation and accident scenarios. The Natural convection Shutdown heat removal Test Facility (NSTF) at Argonne National Laboratory (“Argonne”) is a half-scale model of the primary features of one conceptual air-cooled RCCS design. The facility was constructed to carry out highly instrumented experiments to study the performance of the RCCS concept for reactor decay heat removal that relies on natural convection cooling. Parallel modeling and simulation efforts were performed to support the design, operation, and analysis of the natural convection system. Throughout the testing program, strong influences of ambient conditions were observed in the experimental data when baseline tests were repeated under the same test procedures. Thus, significant analysis efforts were devoted to gaining a better understanding of these influences and the subsequent response of the NSTF to ambient conditions. It was determined that air humidity had negligible impacts on NSTF system performance and therefore did not warrant consideration in the models. However, temperature differences between the building exterior and interior air, along with the outside wind speed, were shown to be dominant factors. Combining the stack and wind effects together, an empirical model was developed based on theoretical considerations and using experimental data to correlate zero-power system flow rates with ambient meteorological conditions. Some coefficients in the model were obtained based on best fitting the experimental data. The predictive capability of the empirical model was demonstrated by applying it to the new set of experimental data. The

Simulating reservoir lithologies by an actively conditioned Markov chain model

Science.gov (United States)

Feng, Runhai; Luthi, Stefan M.; Gisolf, Dries

2018-06-01

The coupled Markov chain model can be used to simulate reservoir lithologies between wells, by conditioning them on the observed data in the cored wells. However, with this method, only the state at the same depth as the current cell is going to be used for conditioning, which may be a problem if the geological layers are dipping. This will cause the simulated lithological layers to be broken or to become discontinuous across the reservoir. In order to address this problem, an actively conditioned process is proposed here, in which a tolerance angle is predefined. The states contained in the region constrained by the tolerance angle will be employed for conditioning in the horizontal chain first, after which a coupling concept with the vertical chain is implemented. In order to use the same horizontal transition matrix for different future states, the tolerance angle has to be small. This allows the method to work in reservoirs without complex structures caused by depositional processes or tectonic deformations. Directional artefacts in the modeling process are avoided through a careful choice of the simulation path. The tolerance angle and dipping direction of the strata can be obtained from a correlation between wells, or from seismic data, which are available in most hydrocarbon reservoirs, either by interpretation or by inversion that can also assist the construction of a horizontal probability matrix.

Urban search mobile platform modeling in hindered access conditions

Science.gov (United States)

Barankova, I. I.; Mikhailova, U. V.; Kalugina, O. B.; Barankov, V. V.

2018-05-01

The article explores the control system simulation and the design of the experimental model of the rescue robot mobile platform. The functional interface, a structural functional diagram of the mobile platform control unit, and a functional control scheme for the mobile platform of secure robot were modeled. The task of design a mobile platform for urban searching in hindered access conditions is realized through the use of a mechanical basis with a chassis and crawler drive, a warning device, human heat sensors and a microcontroller based on Arduino platforms.

Repairable-conditionally repairable damage model based on dual Poisson processes.

Science.gov (United States)

Lind, B K; Persson, L M; Edgren, M R; Hedlöf, I; Brahme, A

2003-09-01

The advent of intensity-modulated radiation therapy makes it increasingly important to model the response accurately when large volumes of normal tissues are irradiated by controlled graded dose distributions aimed at maximizing tumor cure and minimizing normal tissue toxicity. The cell survival model proposed here is very useful and flexible for accurate description of the response of healthy tissues as well as tumors in classical and truly radiobiologically optimized radiation therapy. The repairable-conditionally repairable (RCR) model distinguishes between two different types of damage, namely the potentially repairable, which may also be lethal, i.e. if unrepaired or misrepaired, and the conditionally repairable, which may be repaired or may lead to apoptosis if it has not been repaired correctly. When potentially repairable damage is being repaired, for example by nonhomologous end joining, conditionally repairable damage may require in addition a high-fidelity correction by homologous repair. The induction of both types of damage is assumed to be described by Poisson statistics. The resultant cell survival expression has the unique ability to fit most experimental data well at low doses (the initial hypersensitive range), intermediate doses (on the shoulder of the survival curve), and high doses (on the quasi-exponential region of the survival curve). The complete Poisson expression can be approximated well by a simple bi-exponential cell survival expression, S(D) = e(-aD) + bDe(-cD), where the first term describes the survival of undamaged cells and the last term represents survival after complete repair of sublethal damage. The bi-exponential expression makes it easy to derive D(0), D(q), n and alpha, beta values to facilitate comparison with classical cell survival models.

Acoustic Measurements of a Large Civil Transport Main Landing Gear Model

Science.gov (United States)

Ravetta, Patricio A.; Khorrami, Mehdi R.; Burdisso, Ricardo A.; Wisda, David M.

2016-01-01

Microphone phased array acoustic measurements of a 26 percent-scale, Boeing 777-200 main landing gear model with and without noise reduction fairings installed were obtained in the anechoic configuration of the Virginia Tech Stability Tunnel. Data were acquired at Mach numbers of 0.12, 0.15, and 0.17 with the latter speed used as the nominal test condition. The fully and partially dressed gear with the truck angle set at 13 degrees toe-up landing configuration were the two most extensively tested configurations, serving as the baselines for comparison purposes. Acoustic measurements were also acquired for the same two baseline configurations with the truck angle set at 0 degrees. In addition, a previously tested noise reducing, toboggan-shaped fairing was re-evaluated extensively to address some of the lingering questions regarding the extent of acoustic benefit achievable with this device. The integrated spectra generated from the acoustic source maps reconfirm, in general terms, the previously reported noise reduction performance of the toboggan fairing as installed on an isolated gear. With the recent improvements to the Virginia Tech tunnel acoustic quality and microphone array capabilities, the present measurements provide an additional, higher quality database to the acoustic information available for this gear model.

In Vitro Disease Model of Microgravity Conditioning on Human Energy Metabolism

Science.gov (United States)

Snyder, Jessica; Culbertson, C.; Zhang, Ye; Emami, K.; Wu, H.; Sun, Wei

2010-01-01

NASA and its partners are committed to introducing appropriate new technology to enable learning and living safely beyond the Earth for extended periods of time in a sustainable and possibly indefinite manner. In the responsible acquisition of that goal, life sciences is tasked to tune and advance current medical technology to prepare for human health and wellness in the space environment. The space environment affects the condition and function of biological systems from organ level function to shape of individual organelles. The objective of this paper is to study the effect of microgravity on kinetics of drug metabolism. This fundamental characterization is meaningful to (1) scientific understanding of the response of biology to microgravity and (2) clinical dosing requirements and pharmacological thresholds during long term manned space exploration. Metabolism kinetics of the anti-nausea drug promethazine (PMZ) were determined by an in vitro ground model of 3-dimensional aggregates of human hepatocytes conditioned to weightlessness using a rotating wall bioreactor. The authors observed up-regulated PMZ conversion in model microgravity conditions and attribute this to effect to model microgravity conditioning acting on metabolic mechanisms of the cells. Further work is necessary to determine which particular cellular mechanisms are governing the experimental observations, but the authors conclude kinetics of drug metabolism are responsive to gravitational fields and further study of this sensitivity would improve dosing of pharmaceuticals to persons exposed to a microgravity environment.

Influence of the Outer Boundary Condition on models of AGB stars

Science.gov (United States)

Wagstaff, G.; Weiss, A.

2018-04-01

Current implementations of the stellar atmosphere typically derive boundary conditions for the interior model from either grey plane-parallel atmospheres or scaled solar atmospheres, neither of which can be considered to have appropriate underlying assumptions for the Thermally Pulsing Asymptotic Giant Branch (TP-AGB). This paper discusses the treatment and influence of the outer boundary condition within stellar evolution codes, and the resulting effects on the AGB evolution. The complex interaction of processes, such as the third dredge up and mass loss, governing the TP-AGB can be affected by varying the treatment of this boundary condition. Presented here are the results from altering the geometry, opacities and the implementation of a grid of MARCS/COMARCS model atmospheres in order to improve this treatment. Although there are changes in the TP-AGB evolution, observable quantities, such as the final core mass, are not significantly altered as a result of the change of atmospheric treatment. During the course of the investigation, a previously unseen phenomena in the AGB models was observed and further investigated. This is believed to be physical, although arising from specific conditions which make its presence unlikely. If it were present in stars, this phenomenon would increase the carbon-star lifetime above 10Myr and increase the final core mass by ˜0.1M⊙ in the narrow initial-mass range where it was observed (˜2 - 2.3M⊙).

76 FR 17022 - Special Conditions: Gulfstream Model GVI Airplane; High Incidence Protection

Science.gov (United States)

2011-03-28

... Special Conditions No. 25-423-SC] Special Conditions: Gulfstream Model GVI Airplane; High Incidence... for transport category airplanes associated with the use of high incidence protection. The applicable... with an executive cabin interior. The maximum takeoff weight will be 99,600 pounds, with a maximum...

A simulation Model of the Reactor Hall Ventilation and air Conditioning Systems of ETRR-2

International Nuclear Information System (INIS)

Abd El-Rahman, M.F.

2004-01-01

Although the conceptual design for any system differs from one designer to another. each of them aims to achieve the function of the system required. the ventilation and air conditioning system of reactors hall is one of those systems that really differs but always dose its function for which it is designed. thus, ventilation and air conditioning in some reactor hall constitute only one system whereas in some other ones, they are separate systems. the Egypt Research Reactor-2 (ETRR-2)represents the second type. most studies conducted on ventilation and air conditioning simulation models either in traditional building or for research rectors show that those models were not designed similarly to the model of the hall of ETRR-2 in which ventilation and air conditioning constitute two separate systems.besides, those studies experimented on ventilation and air conditioning simulation models of reactor building predict the temperature and humidity inside these buildings at certain outside condition and it is difficult to predict when the outside conditions are changed . also those studies do not discuss the influences of reactor power changes. therefore, the present work deals with a computational study backed by infield experimental measurements of the performance of the ventilation and air conditioning systems of reactor hall during normal operation at different outside conditions as well as at different levels of reactor power

Preliminary Two-Phase Terry Turbine Nozzle Models for RCIC Off-Design Operation Conditions

Energy Technology Data Exchange (ETDEWEB)

Zhao, Haihua [Idaho National Lab. (INL), Idaho Falls, ID (United States); O' Brien, James [Idaho National Lab. (INL), Idaho Falls, ID (United States)

2017-06-12

This report presents the effort to extend the single-phase analytical Terry turbine model to cover two-phase off-design conditions. The work includes: (1) adding well-established two-phase choking models – the Isentropic Homogenous Equilibrium Model (IHEM) and Moody’s model, and (2) theoretical development and implementation of a two-phase nozzle expansion model. The two choking models provide bounding cases for the two-phase choking mass flow rate. The new two-phase Terry turbine model uses the choking models to calculate the mass flow rate, the critical pressure at the nozzle throat, and steam quality. In the divergent stage, we only consider the vapor phase with a similar model for the single-phase case by assuming that the liquid phase would slip along the wall with a much slower speed and will not contribute the impulse on the rotor. We also modify the stagnation conditions according to two-phase choking conditions at the throat and the cross-section areas for steam flow at the nozzle throat and at the nozzle exit. The new two-phase Terry turbine model was benchmarked with the same steam nozzle test as for the single-phase model. Better agreement with the experimental data is observed than from the single-phase model. We also repeated the Terry turbine nozzle benchmark work against the Sandia CFD simulation results with the two-phase model for the pure steam inlet nozzle case. The RCIC start-up tests were simulated and compared with the single-phase model. Similar results are obtained. Finally, we designed a new RCIC system test case to simulate the self-regulated Terry turbine behavior observed in Fukushima accidents. In this test, a period inlet condition for the steam quality varying from 1 to 0 is applied. For the high quality inlet period, the RCIC system behaves just like the normal operation condition with a high pump injection flow rate and a nominal steam release rate through the turbine, with the net addition of water to the primary system; for

Modeling of composite synthesis in conditions of controlled thermal explosion

Science.gov (United States)

Kukta, Yaroslav; Knyazeva, Anna

2017-12-01

The paper proposes the model for the titanium-based composite synthesis from powders of titanium and carbon of non-stoichiometric composition. The model takes into account the mixture heating from chamber walls, the dependence of liquidus and solidus temperatures on the composition of reacting mixture and the formation of possible irreversible phases. The reaction retardation by the reaction product is taken into consideration in kinetic laws. As an example, the results of temperature and conversion level calculation are presented for the system Ti-C with the summary reaction for different temperatures of chamber walls heating. It was revealed that the reaction retardation being the reaction product can be the cause of incomplete conversion in the thermal explosion conditions. Non-stoichiometric composition leads to the conditions of degenerated mode when some additional heating is necessary to complete the reaction.

Bayesian informative dropout model for longitudinal binary data with random effects using conditional and joint modeling approaches.

Science.gov (United States)

Chan, Jennifer S K

2016-05-01

Dropouts are common in longitudinal study. If the dropout probability depends on the missing observations at or after dropout, this type of dropout is called informative (or nonignorable) dropout (ID). Failure to accommodate such dropout mechanism into the model will bias the parameter estimates. We propose a conditional autoregressive model for longitudinal binary data with an ID model such that the probabilities of positive outcomes as well as the drop-out indicator in each occasion are logit linear in some covariates and outcomes. This model adopting a marginal model for outcomes and a conditional model for dropouts is called a selection model. To allow for the heterogeneity and clustering effects, the outcome model is extended to incorporate mixture and random effects. Lastly, the model is further extended to a novel model that models the outcome and dropout jointly such that their dependency is formulated through an odds ratio function. Parameters are estimated by a Bayesian approach implemented using the user-friendly Bayesian software WinBUGS. A methadone clinic dataset is analyzed to illustrate the proposed models. Result shows that the treatment time effect is still significant but weaker after allowing for an ID process in the data. Finally the effect of drop-out on parameter estimates is evaluated through simulation studies. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

75 FR 80735 - Special Conditions: Gulfstream Model GVI Airplane; High Incidence Protection

Science.gov (United States)

2010-12-23

... Special Conditions No. 25-10-03-SC] Special Conditions: Gulfstream Model GVI Airplane; High Incidence... airworthiness standards for transport category airplanes associated with the use of high incidence protection... transport airplane with an executive cabin interior. The maximum takeoff weight will be 99,600 pounds, with...

Age-dependent reliability model considering effects of maintenance and working conditions

International Nuclear Information System (INIS)

Martorell, Sebastian; Sanchez, Ana; Serradell, Vicente

1999-01-01

Nowadays, there is some doubt about building new nuclear power plants (NPPs). Instead, there is a growing interest in analyzing the possibility to extend current NPP operation, where life management programs play an important role. The evolution of the NPP safety depends on the evolution of the reliability of its safety components, which, in turn, is a function of their age along the NPP operational life. In this paper, a new age-dependent reliability model is presented, which includes parameters related to surveillance and maintenance effectiveness and working conditions of the equipment, both environmental and operational. This model may be used to support NPP life management and life extension programs, by improving or optimizing surveillance and maintenance tasks using risk and cost models based on such an age-dependent reliability model. The results of the sensitivity study in the example application show that the selection of the most appropriate maintenance strategy would directly depend on the previous parameters. Then, very important differences are expected to appear under certain circumstances, particularly, in comparison with other models that do not consider maintenance effectiveness and working conditions simultaneously

Reductions in biomarkers of exposure (BoE) to harmful or potentially harmful constituents (HPHCs) following partial or complete substitution of cigarettes with electronic cigarettes in adult smokers

Science.gov (United States)

O’Connell, Grant; Graff, Donald W.; D’Ruiz, Carl D.

2016-01-01

Abstract Changes in fifteen urine, blood and exhaled breath BoEs of HPHCs representing classes of compounds reported by FDA to be significant contributors to smoking-associated disease risks were measured in 105 clinical-confined subjects following randomization and a five-day forced-switch from usual brand conventional combustible cigarettes to: (i) exclusive commercial e-cigarette use; (ii) dual-use of commercial e-cigarettes and the subject’s usual cigarette brand; or (iii) discontinued use of all tobacco or nicotine products. Levels of urinary biomarkers in subjects that completely substituted their usual cigarette with e-cigarettes were significantly lower (29–95%) after 5 days. Percent reductions in eight of nine urinary BoEs were indistinguishable to smokers who had quit smoking, except for nicotine equivalents, which declined by 25–40%. Dual users who halved self-reported daily cigarette consumption with e-cigarettes exhibited reductions (7–38%) in eight of nine urinary biomarkers, but had increase (1–20%) in nicotine equivalents. Reductions were broadly proportional to the reduced numbers of cigarettes smoked. Dual user urinary nicotine equivalents were slightly higher, but not statistically significant. After 5 days, blood nicotine biomarker levels were lower in the cessation (75–96%) and exclusive use groups (11–83%); with dual users experiencing no significant reductions. All subjects experienced significant decreases in exhaled CO. Decreases in the cessation and exclusive groups ranged from 88–89% and 27–32% in dual users. Exhaled NO increased in the cessation and exclusive groups (46–63% respectively), whereas the dual users experienced minimal changes. Overall, smokers who completely or partially substituted conventional cigarettes with e-cigarettes over five days, experienced reductions in HPHCs. PMID:27401591

Asymptotics for the conditional-sum-of-squares estimator in multivariate fractional time series models

DEFF Research Database (Denmark)

Ørregård Nielsen, Morten

This paper proves consistency and asymptotic normality for the conditional-sum-of-squares estimator, which is equivalent to the conditional maximum likelihood estimator, in multivariate fractional time series models. The model is parametric and quite general, and, in particular, encompasses...... the multivariate non-cointegrated fractional ARIMA model. The novelty of the consistency result, in particular, is that it applies to a multivariate model and to an arbitrarily large set of admissible parameter values, for which the objective function does not converge uniformly in probablity, thus making...

Applicability of common stomatal conductance models in maize under varying soil moisture conditions.

Science.gov (United States)

Wang, Qiuling; He, Qijin; Zhou, Guangsheng

2018-07-01

In the context of climate warming, the varying soil moisture caused by precipitation pattern change will affect the applicability of stomatal conductance models, thereby affecting the simulation accuracy of carbon-nitrogen-water cycles in ecosystems. We studied the applicability of four common stomatal conductance models including Jarvis, Ball-Woodrow-Berry (BWB), Ball-Berry-Leuning (BBL) and unified stomatal optimization (USO) models based on summer maize leaf gas exchange data from a soil moisture consecutive decrease manipulation experiment. The results showed that the USO model performed best, followed by the BBL model, BWB model, and the Jarvis model performed worst under varying soil moisture conditions. The effects of soil moisture made a difference in the relative performance among the models. By introducing a water response function, the performance of the Jarvis, BWB, and USO models improved, which decreased the normalized root mean square error (NRMSE) by 15.7%, 16.6% and 3.9%, respectively; however, the performance of the BBL model was negative, which increased the NRMSE by 5.3%. It was observed that the models of Jarvis, BWB, BBL and USO were applicable within different ranges of soil relative water content (i.e., 55%-65%, 56%-67%, 37%-79% and 37%-95%, respectively) based on the 95% confidence limits. Moreover, introducing a water response function, the applicability of the Jarvis and BWB models improved. The USO model performed best with or without introducing the water response function and was applicable under varying soil moisture conditions. Our results provide a basis for selecting appropriate stomatal conductance models under drought conditions. Copyright © 2018 Elsevier B.V. All rights reserved.

MODELS OF AIR TRAFFIC CONTROLLERS ERRORS PREVENTION IN TERMINAL CONTROL AREAS UNDER UNCERTAINTY CONDITIONS

Directory of Open Access Journals (Sweden)

Volodymyr Kharchenko

2017-03-01

Full Text Available Purpose: the aim of this study is to research applied models of air traffic controllers’ errors prevention in terminal control areas (TMA under uncertainty conditions. In this work the theoretical framework descripting safety events and errors of air traffic controllers connected with the operations in TMA is proposed. Methods: optimisation of terminal control area formal description based on the Threat and Error management model and the TMA network model of air traffic flows. Results: the human factors variables associated with safety events in work of air traffic controllers under uncertainty conditions were obtained. The Threat and Error management model application principles to air traffic controller operations and the TMA network model of air traffic flows were proposed. Discussion: Information processing context for preventing air traffic controller errors, examples of threats in work of air traffic controllers, which are relevant for TMA operations under uncertainty conditions.

Predictive Uncertainty Estimation in Water Demand Forecasting Using the Model Conditional Processor

Directory of Open Access Journals (Sweden)

Amos O. Anele

2018-04-01

Full Text Available In a previous paper, a number of potential models for short-term water demand (STWD prediction have been analysed to find the ones with the best fit. The results obtained in Anele et al. (2017 showed that hybrid models may be considered as the accurate and appropriate forecasting models for STWD prediction. However, such best single valued forecast does not guarantee reliable and robust decisions, which can be properly obtained via model uncertainty processors (MUPs. MUPs provide an estimate of the full predictive densities and not only the single valued expected prediction. Amongst other MUPs, the purpose of this paper is to use the multi-variate version of the model conditional processor (MCP, proposed by Todini (2008, to demonstrate how the estimation of the predictive probability conditional to a number of relatively good predictive models may improve our knowledge, thus reducing the predictive uncertainty (PU when forecasting into the unknown future. Through the MCP approach, the probability distribution of the future water demand can be assessed depending on the forecast provided by one or more deterministic forecasting models. Based on an average weekly data of 168 h, the probability density of the future demand is built conditional on three models’ predictions, namely the autoregressive-moving average (ARMA, feed-forward back propagation neural network (FFBP-NN and hybrid model (i.e., combined forecast from ARMA and FFBP-NN. The results obtained show that MCP may be effectively used for real-time STWD prediction since it brings out the PU connected to its forecast, and such information could help water utilities estimate the risk connected to a decision.

Numerical modelling of multi-vane expander operating conditions in ORC system

Science.gov (United States)

Rak, Józef; Błasiak, Przemysław; Kolasiński, Piotr

2017-11-01

Multi-vane expanders are positive displacement volumetric machines which are nowadays considered for application in micro-power domestic ORC systems as promising alternative to micro turbines and other volumetric expanders. The multi-vane expander features very simple design, low gas flow capacity, low expansion ratios, an advantageous ratio of the power output to the external dimensions and are insensitive to the negative influence of the gas-liquid mixture expansion. Moreover, the multi-vane expander can be easily hermetically sealed, which is one of the key issues in the ORC system design. A literature review indicates that issues concerning the application of multi-vane expanders in such systems, especially related to operating of multi-vane expander with different low-boiling working fluids, are innovative, not fully scientifically described and have the potential for practical implementation. In this paper the results of numerical investigations on multi-vane expander operating conditions are presented. The analyses were performed on three-dimensional numerical model of the expander in ANSYS CFX software. The numerical model of the expander was validated using the data obtained from the experiment carried out on a lab test-stand. Then a series of computational analysis were performed using expanders' numerical model in order to determine its operating conditions under various flow conditions of different working fluids.

Groundwater flow modelling of periods with temperate climate conditions - Laxemar

International Nuclear Information System (INIS)

Joyce, Steven; Simpson, Trevor; Hartley, Lee; Applegate, David; Hoek, Jaap; Jackson, Peter; Roberts, David; Swan, David; Gylling, Bjoern; Marsic, Niko; Rhen, Ingvar

2010-12-01

As a part of the license application for a final repository for spent nuclear fuel at Forsmark, the Swedish Nuclear Fuel and Waste Management Company (SKB) has undertaken a series of groundwater flow modelling studies. These represent time periods with different hydraulic conditions and the simulations carried out contribute to the overall evaluation of the repository design and long-term radiological safety. This report concerns the modelling of a repository at the Laxemar-Simpevarp site during temperate climate conditions as a comparison to corresponding modelling carried out for Forsmark /Joyce et al. 2010/. The collation and implementation of onsite hydrogeological and hydrogeochemical data from previous reports are used in the construction of a Hydrogeological base case (reference case conceptualisation) and then an examination of various areas of uncertainty within the current understanding by a series of model variants. The Hydrogeological base case models at three different scales, 'repository', 'site' and 'regional' make use of a discrete fracture network (DFN) and equivalent continuous porous medium (ECPM) models. The use of hydrogeological models allow for the investigation of the groundwater flow from a deep disposal facility to the biosphere and for the calculation of performance measures that will provide an input to the site performance assessment. The focus of the study described in this report has been to perform numerical simulations of the hydrogeological system from post-closure and throughout the temperate period up until the receding shoreline leaves the modelling domain at around 15,000 AD. Besides providing quantitative results for the immediate temperate period following post-closure, these results are also intended to give a qualitative indication of the evolution of the groundwater system during future temperate periods within an ongoing cycle of glacial/inter-glacial events

Groundwater flow modelling of periods with temperate climate conditions - Laxemar

Energy Technology Data Exchange (ETDEWEB)

Joyce, Steven; Simpson, Trevor; Hartley, Lee; Applegate, David; Hoek, Jaap; Jackson, Peter; Roberts, David; Swan, David (Serco Technical Consulting Services (United Kingdom)); Gylling, Bjoern; Marsic, Niko (Kemakta Konsult AB, Stockholm (Sweden)); Rhen, Ingvar (SWECO Environment AB, Falun (Sweden))

2010-12-15

As a part of the license application for a final repository for spent nuclear fuel at Forsmark, the Swedish Nuclear Fuel and Waste Management Company (SKB) has undertaken a series of groundwater flow modelling studies. These represent time periods with different hydraulic conditions and the simulations carried out contribute to the overall evaluation of the repository design and long-term radiological safety. This report concerns the modelling of a repository at the Laxemar-Simpevarp site during temperate climate conditions as a comparison to corresponding modelling carried out for Forsmark /Joyce et al. 2010/. The collation and implementation of onsite hydrogeological and hydrogeochemical data from previous reports are used in the construction of a Hydrogeological base case (reference case conceptualisation) and then an examination of various areas of uncertainty within the current understanding by a series of model variants. The Hydrogeological base case models at three different scales, 'repository', 'site' and 'regional' make use of a discrete fracture network (DFN) and equivalent continuous porous medium (ECPM) models. The use of hydrogeological models allow for the investigation of the groundwater flow from a deep disposal facility to the biosphere and for the calculation of performance measures that will provide an input to the site performance assessment. The focus of the study described in this report has been to perform numerical simulations of the hydrogeological system from post-closure and throughout the temperate period up until the receding shoreline leaves the modelling domain at around 15,000 AD. Besides providing quantitative results for the immediate temperate period following post-closure, these results are also intended to give a qualitative indication of the evolution of the groundwater system during future temperate periods within an ongoing cycle of glacial/inter-glacial events

Determination of particle-release conditions in microfiltration: A simple single-particle model tested on a model membrane

NARCIS (Netherlands)

Kuiper, S.; van Rijn, C.J.M.; Nijdam, W.; Krijnen, Gijsbertus J.M.; Elwenspoek, Michael Curt

2000-01-01

A simple single-particle model was developed for cross-flow microfiltration with microsieves. The model describes the cross-flow conditions required to release a trapped spherical particle from a circular pore. All equations are derived in a fully analytical way without any fitting parameters. For

Homologous Basal Ganglia Network Models in Physiological and Parkinsonian Conditions

Directory of Open Access Journals (Sweden)

Jyotika Bahuguna

2017-08-01

Full Text Available The classical model of basal ganglia has been refined in recent years with discoveries of subpopulations within a nucleus and previously unknown projections. One such discovery is the presence of subpopulations of arkypallidal and prototypical neurons in external globus pallidus, which was previously considered to be a primarily homogeneous nucleus. Developing a computational model of these multiple interconnected nuclei is challenging, because the strengths of the connections are largely unknown. We therefore use a genetic algorithm to search for the unknown connectivity parameters in a firing rate model. We apply a binary cost function derived from empirical firing rate and phase relationship data for the physiological and Parkinsonian conditions. Our approach generates ensembles of over 1,000 configurations, or homologies, for each condition, with broad distributions for many of the parameter values and overlap between the two conditions. However, the resulting effective weights of connections from or to prototypical and arkypallidal neurons are consistent with the experimental data. We investigate the significance of the weight variability by manipulating the parameters individually and cumulatively, and conclude that the correlation observed between the parameters is necessary for generating the dynamics of the two conditions. We then investigate the response of the networks to a transient cortical stimulus, and demonstrate that networks classified as physiological effectively suppress activity in the internal globus pallidus, and are not susceptible to oscillations, whereas parkinsonian networks show the opposite tendency. Thus, we conclude that the rates and phase relationships observed in the globus pallidus are predictive of experimentally observed higher level dynamical features of the physiological and parkinsonian basal ganglia, and that the multiplicity of solutions generated by our method may well be indicative of a natural

Local Stability Conditions for Two Types of Monetary Models with Recursive Utility

OpenAIRE

Miyazaki, Kenji; Utsunomiya, Hitoshi

2009-01-01

This paper explores local stability conditions for money-in-utility-function (MIUF) and transaction-costs (TC) models with recursive utility.A monetary variant of the Brock-Gale condition provides a theoretical justification of the comparative statics analysis. One of sufficient conditions for local stability is increasing marginal impatience (IMI) in consumption and money. However, this does not deny the possibility of decreasing marginal impatience (DMI). The local stability with DMI is mor...

Rate Theory Modeling and Simulation of Silicide Fuel at LWR Conditions

Energy Technology Data Exchange (ETDEWEB)

Miao, Yinbin [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Ye, Bei [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Hofman, Gerard [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Yacout, Abdellatif [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division; Gamble, Kyle [Idaho National Lab. (INL), Idaho Falls, ID (United States). Fuel Modeling and Simulation; Mei, Zhi-Gang [Argonne National Lab. (ANL), Argonne, IL (United States). Nuclear Engineering Division

2016-08-29

As a promising candidate for the accident tolerant fuel (ATF) used in light water reactors (LWRs), the fuel performance of uranium silicide (U₃Si₂) at LWR conditions needs to be well understood. In this report, rate theory model was developed based on existing experimental data and density functional theory (DFT) calculations so as to predict the fission gas behavior in U₃Si₂ at LWR conditions. The fission gas behavior of U₃Si₂ can be divided into three temperature regimes. During steady-state operation, the majority of the fission gas stays in intragranular bubbles, whereas the dominance of intergranular bubbles and fission gas release only occurs beyond 1000 K. The steady-state rate theory model was also used as reference to establish a gaseous swelling correlation of U₃Si₂ for the BISON code. Meanwhile, the overpressurized bubble model was also developed so that the fission gas behavior at LOCA can be simulated. LOCA simulation showed that intragranular bubbles are still dominant after a 70 second LOCA, resulting in a controllable gaseous swelling. The fission gas behavior of U₃Si₂ at LWR conditions is benign according to the rate theory prediction at both steady-state and LOCA conditions, which provides important references to the qualification of U₃Si₂ as a LWR fuel material with excellent fuel performance and enhanced accident tolerance.

Multistressor predictive models of invertebrate condition in the Corn Belt, USA

Science.gov (United States)

Waite, Ian R.; Van Metre, Peter C.

2017-01-01

Understanding the complex relations between multiple environmental stressors and ecological conditions in streams can help guide resource-management decisions. During 14 weeks in spring/summer 2013, personnel from the US Geological Survey and the US Environmental Protection Agency sampled 98 wadeable streams across the Midwest Corn Belt region of the USA for water and sediment quality, physical and habitat characteristics, and ecological communities. We used these data to develop independent predictive disturbance models for 3 macroinvertebrate metrics and a multimetric index. We developed the models based on boosted regression trees (BRT) for 3 stressor categories, land use/land cover (geographic information system [GIS]), all in-stream stressors combined (nutrients, habitat, and contaminants), and for GIS plus in-stream stressors. The GIS plus in-stream stressor models had the best overall performance with an average cross-validation R2 across all models of 0.41. The models were generally consistent in the explanatory variables selected within each stressor group across the 4 invertebrate metrics modeled. Variables related to riparian condition, substrate size or embeddedness, velocity and channel shape, nutrients (primarily NH3), and contaminants (pyrethroid degradates) were important descriptors of the invertebrate metrics. Models based on all measured in-stream stressors performed comparably to models based on GIS landscape variables, suggesting that the in-stream stressor characterization reasonably represents the dominant factors affecting invertebrate communities and that GIS variables are acting as surrogates for in-stream stressors that directly affect in-stream biota.

Evaluating the performance of ENVI-met model in diurnal cycles for different meteorological conditions

Science.gov (United States)

Acero, Juan A.; Arrizabalaga, Jon

2018-01-01

Urban areas are known to modify meteorological variables producing important differences in small spatial scales (i.e. microscale). These affect human thermal comfort conditions and the dispersion of pollutants, especially those emitted inside the urban area, which finally influence quality of life and the use of public open spaces. In this study, the diurnal evolution of meteorological variables measured in four urban spaces is compared with the results provided by ENVI-met (v 4.0). Measurements were carried out during 3 days with different meteorological conditions in Bilbao in the north of the Iberian Peninsula. The evaluation of the model accuracy (i.e. the degree to which modelled values approach measured values) was carried out with several quantitative difference metrics. The results for air temperature and humidity show a good agreement of measured and modelled values independently of the regional meteorological conditions. However, in the case of mean radiant temperature and wind speed, relevant differences are encountered highlighting the limitation of the model to estimate these meteorological variables precisely during diurnal cycles, in the considered evaluation conditions (sites and weather).

An application of probabilistic safety assessment methods to model aircraft systems and accidents

Energy Technology Data Exchange (ETDEWEB)

Martinez-Guridi, G.; Hall, R.E.; Fullwood, R.R.

1998-08-01

A case study modeling the thrust reverser system (TRS) in the context of the fatal accident of a Boeing 767 is presented to illustrate the application of Probabilistic Safety Assessment methods. A simplified risk model consisting of an event tree with supporting fault trees was developed to represent the progression of the accident, taking into account the interaction between the TRS and the operating crew during the accident, and the findings of the accident investigation. A feasible sequence of events leading to the fatal accident was identified. Several insights about the TRS and the accident were obtained by applying PSA methods. Changes proposed for the TRS also are discussed.

Do downscaled general circulation models reliably simulate historical climatic conditions?

Science.gov (United States)

Bock, Andrew R.; Hay, Lauren E.; McCabe, Gregory J.; Markstrom, Steven L.; Atkinson, R. Dwight

2018-01-01

The accuracy of statistically downscaled (SD) general circulation model (GCM) simulations of monthly surface climate for historical conditions (1950–2005) was assessed for the conterminous United States (CONUS). The SD monthly precipitation (PPT) and temperature (TAVE) from 95 GCMs from phases 3 and 5 of the Coupled Model Intercomparison Project (CMIP3 and CMIP5) were used as inputs to a monthly water balance model (MWBM). Distributions of MWBM input (PPT and TAVE) and output [runoff (RUN)] variables derived from gridded station data (GSD) and historical SD climate were compared using the Kolmogorov–Smirnov (KS) test For all three variables considered, the KS test results showed that variables simulated using CMIP5 generally are more reliable than those derived from CMIP3, likely due to improvements in PPT simulations. At most locations across the CONUS, the largest differences between GSD and SD PPT and RUN occurred in the lowest part of the distributions (i.e., low-flow RUN and low-magnitude PPT). Results indicate that for the majority of the CONUS, there are downscaled GCMs that can reliably simulate historical climatic conditions. But, in some geographic locations, none of the SD GCMs replicated historical conditions for two of the three variables (PPT and RUN) based on the KS test, with a significance level of 0.05. In these locations, improved GCM simulations of PPT are needed to more reliably estimate components of the hydrologic cycle. Simple metrics and statistical tests, such as those described here, can provide an initial set of criteria to help simplify GCM selection.

Equilibrium and kinetic models for colloid release under transient solution chemistry conditions

Science.gov (United States)

We present continuum models to describe colloid release in the subsurface during transient physicochemical conditions. Our modeling approach relates the amount of colloid release to changes in the fraction of the solid surface area that contributes to retention. Equilibrium, kinetic, equilibrium and...

Multiphase-field model of small strain elasto-plasticity according to the mechanical jump conditions

Science.gov (United States)

Herrmann, Christoph; Schoof, Ephraim; Schneider, Daniel; Schwab, Felix; Reiter, Andreas; Selzer, Michael; Nestler, Britta

2018-04-01

We introduce a small strain elasto-plastic multiphase-field model according to the mechanical jump conditions. A rate-independent J_2 -plasticity model with linear isotropic hardening and without kinematic hardening is applied exemplary. Generally, any physically nonlinear mechanical model is compatible with the subsequently presented procedure. In contrast to models with interpolated material parameters, the proposed model is able to apply different nonlinear mechanical constitutive equations for each phase separately. The Hadamard compatibility condition and the static force balance are employed as homogenization approaches to calculate the phase-inherent stresses and strains. Several verification cases are discussed. The applicability of the proposed model is demonstrated by simulations of the martensitic transformation and quantitative parameters.

Groundwater flow modelling of periods with periglacial and glacial climate conditions - Forsmark

International Nuclear Information System (INIS)

Vidstrand, Patrik; Follin, Sven; Zugec, Nada

2010-12-01

As a part of the license application for a final repository for spent nuclear fuel at Forsmark, the Swedish Nuclear Fuel and Waste Management Company (SKB) has undertaken a series of groundwater flow modelling studies. These represent time periods with different hydraulic conditions and the simulations carried out contribute to the overall evaluation of the repository design and long-term radiological safety. The groundwater flow modelling study reported here comprises a coupled thermal-hydraulic-chemical (T-H-C) analysis of periods with periglacial and glacial climate conditions. Hydraulic-mechanical (H-M) issues are also handled but no coupled flow modelling is done. The objective of the report is to provide bounding hydrogeological estimates at different stages during glaciation and deglaciation of a glacial cycle for subsequent use in safety assessment applications within SKB's project SR-Site. Three cases with different climate conditions are analysed here: (i) Temperate case, (ii) Glacial case without permafrost, and (iii) Glacial case with permafrost. The glacial periods are transient and encompass approximately 19,000 years. The simulation results comprise residual fluid pressures, Darcy fluxes, and water salinities, as well as advective transport performance measures obtained by particle tracking such as flow path lengths, travel times and flow-related transport resistances. The modelling is accompanied by a sensitivity study that addresses the impact of the following matters: the direction of the ice sheet advance, the speed of the ice sheet margin, the bedrock hydraulic and transport properties, the temperature at the ice-subsurface interface close to the ice sheet margin, and the initial hydrochemical conditions

Groundwater flow modelling of periods with periglacial and glacial climate conditions - Forsmark

Energy Technology Data Exchange (ETDEWEB)

Vidstrand, Patrik (TerraSolve AB, Floda (Sweden)); Follin, Sven (SF GeoLogic AB, Taeby (Sweden)); Zugec, Nada (Bergab, Stockholm (Sweden))

2010-12-15

As a part of the license application for a final repository for spent nuclear fuel at Forsmark, the Swedish Nuclear Fuel and Waste Management Company (SKB) has undertaken a series of groundwater flow modelling studies. These represent time periods with different hydraulic conditions and the simulations carried out contribute to the overall evaluation of the repository design and long-term radiological safety. The groundwater flow modelling study reported here comprises a coupled thermal-hydraulic-chemical (T-H-C) analysis of periods with periglacial and glacial climate conditions. Hydraulic-mechanical (H-M) issues are also handled but no coupled flow modelling is done. The objective of the report is to provide bounding hydrogeological estimates at different stages during glaciation and deglaciation of a glacial cycle for subsequent use in safety assessment applications within SKB's project SR-Site. Three cases with different climate conditions are analysed here: (i) Temperate case, (ii) Glacial case without permafrost, and (iii) Glacial case with permafrost. The glacial periods are transient and encompass approximately 19,000 years. The simulation results comprise residual fluid pressures, Darcy fluxes, and water salinities, as well as advective transport performance measures obtained by particle tracking such as flow path lengths, travel times and flow-related transport resistances. The modelling is accompanied by a sensitivity study that addresses the impact of the following matters: the direction of the ice sheet advance, the speed of the ice sheet margin, the bedrock hydraulic and transport properties, the temperature at the ice-subsurface interface close to the ice sheet margin, and the initial hydrochemical conditions.

Modeling the effect of deep impurity ionization on GaAs photoconductive switches

Energy Technology Data Exchange (ETDEWEB)

Yee, J.H.; Khanaka, G.H.; Druce, R.L.; Pocha, M.D.

1992-01-01

The ionization coefficient of deep traps in GaAs is determined from a gas breakdown model together with the recent experimental data obtained at LLNL (Lawrence Livermore National Laboratory) and Boeing. Using this coefficient in our nonlinear device transport code, we have investigated theoretically the nonlinear switching phenomena in GaAs devices. The results obtained from our investigations show that if we take into consideration the effect of the field ionization of the deep traps, we can show how the Lock-On'' phenomena could occur in the device.

Modeling the effect of deep impurity ionization on GaAs photoconductive switches

Energy Technology Data Exchange (ETDEWEB)

Yee, J.H.; Khanaka, G.H.; Druce, R.L.; Pocha, M.D.

1992-01-01

The ionization coefficient of deep traps in GaAs is determined from a gas breakdown model together with the recent experimental data obtained at LLNL (Lawrence Livermore National Laboratory) and Boeing. Using this coefficient in our nonlinear device transport code, we have investigated theoretically the nonlinear switching phenomena in GaAs devices. The results obtained from our investigations show that if we take into consideration the effect of the field ionization of the deep traps, we can show how the ``Lock-On`` phenomena could occur in the device.

Modelling Danish local CHP on market conditions

DEFF Research Database (Denmark)

Ravn, Hans V.; Riisom, Jannik; Schaumburg-Müller, Camilla

2004-01-01

with the liberalisation process of the energy sectors of the EU countries, it is however anticipated that Danish local CHP are to begin operating on market conditions within the year 2005. This means that the income that the local CHPs previously gained from selling electricity at the feed-in tariff is replaced in part...... the consequences of acting in a liberalised market for a given CHP plant, based on the abovementioned bottom-up model. The key assumption determining the bottom line is the electricity spot price. The formation of the spot price in the Nordic area depends heavily upon the state of the water reservoirs in Norway...

Modular Engine Noise Component Prediction System (MCP) Program Users' Guide

Science.gov (United States)

Golub, Robert A. (Technical Monitor); Herkes, William H.; Reed, David H.

2004-01-01

This is a user's manual for Modular Engine Noise Component Prediction System (MCP). This computer code allows the user to predict turbofan engine noise estimates. The program is based on an empirical procedure that has evolved over many years at The Boeing Company. The data used to develop the procedure include both full-scale engine data and small-scale model data, and include testing done by Boeing, by the engine manufacturers, and by NASA. In order to generate a noise estimate, the user specifies the appropriate engine properties (including both geometry and performance parameters), the microphone locations, the atmospheric conditions, and certain data processing options. The version of the program described here allows the user to predict three components: inlet-radiated fan noise, aft-radiated fan noise, and jet noise. MCP predicts one-third octave band noise levels over the frequency range of 50 to 10,000 Hertz. It also calculates overall sound pressure levels and certain subjective noise metrics (e.g., perceived noise levels).

COMPONENT SUPPLY MODEL FOR REPAIR ACTIVITIES NETWORK UNDER CONDITIONS OF PROBABILISTIC INDEFINITENESS.

Directory of Open Access Journals (Sweden)

Victor Yurievich Stroganov

2017-02-01

Full Text Available This article contains the systematization of the major production functions of repair activities network and the list of planning and control functions, which are described in the form of business processes (BP. Simulation model for analysis of the delivery effectiveness of components under conditions of probabilistic uncertainty was proposed. It has been shown that a significant portion of the total number of business processes is represented by the management and planning of the parts and components movement. Questions of construction of experimental design techniques on the simulation model in the conditions of non-stationarity were considered.

76 FR 72087 - Special Conditions: Diamond Aircraft Industries, Model DA-40NG; Electronic Engine Control (EEC...

Science.gov (United States)

2011-11-22

...; Special Conditions No. 23-253-SC] Special Conditions: Diamond Aircraft Industries, Model DA-40NG..., Model DA-40NG airplane. This airplane will have a novel or unusual design feature(s) associated with an... include the new model DA- 40NG with the Austro Engine GmbH model E4 Aircraft Diesel Engine (ADE). The...

Effects of Test Conditions on APA Rutting and Prediction Modeling for Asphalt Mixtures

Directory of Open Access Journals (Sweden)

Hui Wang

2017-01-01

Full Text Available APA rutting tests were conducted for six kinds of asphalt mixtures under air-dry and immersing conditions. The influences of test conditions, including load, temperature, air voids, and moisture, on APA rutting depth were analyzed by using grey correlation method, and the APA rutting depth prediction model was established. Results show that the modified asphalt mixtures have bigger rutting depth ratios of air-dry to immersing conditions, indicating that the modified asphalt mixtures have better antirutting properties and water stability than the matrix asphalt mixtures. The grey correlation degrees of temperature, load, air void, and immersing conditions on APA rutting depth decrease successively, which means that temperature is the most significant influencing factor. The proposed indoor APA rutting prediction model has good prediction accuracy, and the correlation coefficient between the predicted and the measured rutting depths is 96.3%.

Equilibrium and kinetic models for colloid release under transient solution chemistry conditions.

Science.gov (United States)

Bradford, Scott A; Torkzaban, Saeed; Leij, Feike; Simunek, Jiri

2015-10-01

We present continuum models to describe colloid release in the subsurface during transient physicochemical conditions. Our modeling approach relates the amount of colloid release to changes in the fraction of the solid surface area that contributes to retention. Equilibrium, kinetic, equilibrium and kinetic, and two-site kinetic models were developed to describe various rates of colloid release. These models were subsequently applied to experimental colloid release datasets to investigate the influence of variations in ionic strength (IS), pH, cation exchange, colloid size, and water velocity on release. Various combinations of equilibrium and/or kinetic release models were needed to describe the experimental data depending on the transient conditions and colloid type. Release of Escherichia coli D21g was promoted by a decrease in solution IS and an increase in pH, similar to expected trends for a reduction in the secondary minimum and nanoscale chemical heterogeneity. The retention and release of 20nm carboxyl modified latex nanoparticles (NPs) were demonstrated to be more sensitive to the presence of Ca(2+) than D21g. Specifically, retention of NPs was greater than D21g in the presence of 2mM CaCl2 solution, and release of NPs only occurred after exchange of Ca(2+) by Na(+) and then a reduction in the solution IS. These findings highlight the limitations of conventional interaction energy calculations to describe colloid retention and release, and point to the need to consider other interactions (e.g., Born, steric, and/or hydration forces) and/or nanoscale heterogeneity. Temporal changes in the water velocity did not have a large influence on the release of D21g for the examined conditions. This insensitivity was likely due to factors that reduce the applied hydrodynamic torque and/or increase the resisting adhesive torque; e.g., macroscopic roughness and grain-grain contacts. Our analysis and models improve our understanding and ability to describe the amounts

Groundwater flow modelling of periods with temperate climate conditions - Forsmark

Energy Technology Data Exchange (ETDEWEB)

Joyce, Steven; Simpson, Trevor; Hartley, Lee; Applegate, David; Hoek, Jaap; Jackson, Peter; Swan, David (Serco Technical Consulting Services (United Kingdom)); Marsic, Niko (Kemakta Konsult AB (Sweden)); Follin, Sven (SF GeoLogic AB (Sweden))

2010-11-15

As a part of the license application for a final repository for spent nuclear fuel at Forsmark, the Swedish Nuclear Fuel and Waste Management Company (SKB) has undertaken a series of groundwater flow modelling studies. These represent time periods with different climate conditions and the simulations carried out contribute to the overall evaluation of the repository design and long-term radiological safety. This report concerns the modelling of a repository at the Forsmark site during temperate conditions; i.e. from post-closure and throughout the temperate period up until the receding shoreline leaves the modelling domain at around 12,000 AD. The collation and implementation of onsite hydrogeological and hydrogeochemical data from previous reports are used in the construction of a hydrogeological base case (reference case conceptualisation) and then in an examination of various areas of uncertainty within the current understanding by a series of model variants. The hydrogeological base case models at three different scales, 'repository', 'site' and 'regional', make use of continuous porous medium (CPM), equivalent continuous porous medium (ECPM) and discrete fracture network (DFN) models. The use of hydrogeological models allow for the investigation of the groundwater flow from a deep disposal facility to the biosphere and for the calculation of performance measures that will provide an input to the site performance assessment. The focus of the study described in this report has been to perform numerical simulations of the hydrogeological system from post-closure and throughout the temperate period. Besides providing quantitative results for the immediate temperate period following post-closure, these results are also intended to give a qualitative indication of the evolution of the groundwater system during future temperate periods within an ongoing cycle of glacial/inter-glacial events

Elements of a pragmatic approach for dealing with bias and uncertainty in experiments through predictions : experiment design and data conditioning; %22real space%22 model validation and conditioning; hierarchical modeling and extrapolative prediction.

Energy Technology Data Exchange (ETDEWEB)

Romero, Vicente Jose

2011-11-01

This report explores some important considerations in devising a practical and consistent framework and methodology for utilizing experiments and experimental data to support modeling and prediction. A pragmatic and versatile 'Real Space' approach is outlined for confronting experimental and modeling bias and uncertainty to mitigate risk in modeling and prediction. The elements of experiment design and data analysis, data conditioning, model conditioning, model validation, hierarchical modeling, and extrapolative prediction under uncertainty are examined. An appreciation can be gained for the constraints and difficulties at play in devising a viable end-to-end methodology. Rationale is given for the various choices underlying the Real Space end-to-end approach. The approach adopts and refines some elements and constructs from the literature and adds pivotal new elements and constructs. Crucially, the approach reflects a pragmatism and versatility derived from working many industrial-scale problems involving complex physics and constitutive models, steady-state and time-varying nonlinear behavior and boundary conditions, and various types of uncertainty in experiments and models. The framework benefits from a broad exposure to integrated experimental and modeling activities in the areas of heat transfer, solid and structural mechanics, irradiated electronics, and combustion in fluids and solids.

Modelling and measurement of wear particle flow in a dual oil filter system for condition monitoring

DEFF Research Database (Denmark)

Henneberg, Morten; Eriksen, René Lynge; Fich, Jens

2016-01-01

. The quantity of wear particles in gear oil is analysed with respect to system running conditions. It is shown that the model fits the data in terms of startup “particle burst” phenomenon, quasi-stationary conditions during operation, and clean-up filtration when placed out of operation. In order to establish...... boundary condition for particle burst phenomenon, the release of wear particles from a pleated mesh filter is measured in a test rig and included in the model. The findings show that a dual filter model, with startup phenomenon included, can describe trends in the wear particle flow observed in the gear...... particle generation is made possible by model parameter estimation and identification of an unintended lack of filter change. The model may also be used to optimise system and filtration performance, and to enable continuous condition monitoring....

Spherically symmetric models with pressure: separating expansion from contraction and generalizing TOV condition

CERN Document Server

Mimoso, José Pedro; Mena, Filipe C

2010-01-01

We investigate spherically symmetric perfect fluid spacetimes and discuss the existence and stability of a dividing shell separating expanding and collapsing regions. We perform a 3+1 splitting and obtain gauge invariant conditions relating the intrinsic spatial curvature of the shells to the ADM mass and to a function of the pressure which we introduce and that generalises the Tolman-Oppenheimer-Volkoff equilibrium condition. We analyse the particular cases of the Lema\\^itre-Tolman-Bondi dust models with a cosmological constant as an example of a $\\Lambda$-CDM model and its generalization to contain a central perfect fluid core. These models provide simple, but physically interesting illustrations of our results.

Numerical modelling of multi-vane expander operating conditions in ORC system

Directory of Open Access Journals (Sweden)

Rak Józef

2017-01-01

Full Text Available Multi-vane expanders are positive displacement volumetric machines which are nowadays considered for application in micro-power domestic ORC systems as promising alternative to micro turbines and other volumetric expanders. The multi-vane expander features very simple design, low gas flow capacity, low expansion ratios, an advantageous ratio of the power output to the external dimensions and are insensitive to the negative influence of the gas-liquid mixture expansion. Moreover, the multi-vane expander can be easily hermetically sealed, which is one of the key issues in the ORC system design. A literature review indicates that issues concerning the application of multi-vane expanders in such systems, especially related to operating of multi-vane expander with different low-boiling working fluids, are innovative, not fully scientifically described and have the potential for practical implementation. In this paper the results of numerical investigations on multi-vane expander operating conditions are presented. The analyses were performed on three-dimensional numerical model of the expander in ANSYS CFX software. The numerical model of the expander was validated using the data obtained from the experiment carried out on a lab test-stand. Then a series of computational analysis were performed using expanders' numerical model in order to determine its operating conditions under various flow conditions of different working fluids.

Interface model conditions for a non-equilibrium heat transfer model for conjugate fluid/porous/solid domains

International Nuclear Information System (INIS)

Betchen, L.J.; Straatman, A.G.

2005-01-01

A mathematical and numerical model for the treatment of conjugate fluid flow and heat transfer problems in domains containing pure fluid, porous, and pure solid regions has been developed. The model is general and physically reasoned, and allows for local thermal non-equilibrium in the porous region. The model is developed for implementation on a simple collocated finite volume grid. Of particular novelty are the conditions implemented at the interfaces between porous regions, and those containing a pure solid or pure fluid. The model is validated by simulation of a three-dimensional porous plug problem for which experimental results are available. (author)

Modeling Bacteria-Water Interactions in Soil: EPS Dynamics Under Evaporative Conditions

Science.gov (United States)

Furrer, J.; Hinestroza, H. F.; Guo, Y. S.; Gage, D. J.; Cho, Y. K.; Shor, L. M.

2017-12-01

The soil habitat represents a major linkage between the water and carbon cycles: the ability of soils to sequester or release carbon is determined primarily by soil moisture. Water retention and distribution in soils controls the abundance and activity of soil microbes. Microbes in turn impact water retention by creating biofilms, composed of extracellular polymeric substances (EPS). We model the effects of bacterial EPS on water retention at the pore scale. We use the lattice Boltzmann method (LBM), a well-established fluid dynamics modeling platform, and modify it to include the effects of water uptake and release by the swelling/shrinking EPS phase. The LB model is implemented in 2-D, with a non-ideal gas equation of state that allows condensation and evaporation of fluid in pore spaces. Soil particles are modeled according to experimentally determined particle size distributions and include realistic pore geometries, in contrast to many soil models which use spherical soil particles for simplicity. Model results are compared with evaporation experiments in soil micromodels and other simpler experimental systems, and model parameters are tuned to match experimental results. Drying behavior and solid-gel contact angle of EPS produced by the soil bacteria Sinorhizobium meliloti has been characterized and compared to the behavior of deionized water under the same conditions. The difference in behavior between the fluids is used to parameterize the model. The model shows excellent qualitative agreement for soil micromodels with both aggregated and non-aggregated particle arrangements under no-EPS conditions, and reproduces realistic drying behavior for EPS. This work represents a multi-disciplinary approach to understanding microbe-soil interactions at the pore scale.

Empirical models of wind conditions on Upper Klamath Lake, Oregon

Science.gov (United States)

Buccola, Norman L.; Wood, Tamara M.

2010-01-01

Upper Klamath Lake is a large (230 square kilometers), shallow (mean depth 2.8 meters at full pool) lake in southern Oregon. Lake circulation patterns are driven largely by wind, and the resulting currents affect the water quality and ecology of the lake. To support hydrodynamic modeling of the lake and statistical investigations of the relation between wind and lake water-quality measurements, the U.S. Geological Survey has monitored wind conditions along the lakeshore and at floating raft sites in the middle of the lake since 2005. In order to make the existing wind archive more useful, this report summarizes the development of empirical wind models that serve two purposes: (1) to fill short (on the order of hours or days) wind data gaps at raft sites in the middle of the lake, and (2) to reconstruct, on a daily basis, over periods of months to years, historical wind conditions at U.S. Geological Survey sites prior to 2005. Empirical wind models based on Artificial Neural Network (ANN) and Multivariate-Adaptive Regressive Splines (MARS) algorithms were compared. ANNs were better suited to simulating the 10-minute wind data that are the dependent variables of the gap-filling models, but the simpler MARS algorithm may be adequate to accurately simulate the daily wind data that are the dependent variables of the historical wind models. To further test the accuracy of the gap-filling models, the resulting simulated winds were used to force the hydrodynamic model of the lake, and the resulting simulated currents were compared to measurements from an acoustic Doppler current profiler. The error statistics indicated that the simulation of currents was degraded as compared to when the model was forced with observed winds, but probably is adequate for short gaps in the data of a few days or less. Transport seems to be less affected by the use of the simulated winds in place of observed winds. The simulated tracer concentration was similar between model results when

An endogenous Taylor condition in an endogenous growth monetary policy model

OpenAIRE

Le, Mai Vo; Gillman, Max; Minford, Patrick

2007-01-01

The paper derives a Taylor condition as part of the agent's equilibrium behavior in an endogenous growth monetary economy. It shows the assumptions necessary to make it almost identical to the original Taylor rule, and that it can interchangably take a money supply growth rate form. From the money supply form, simple policy experiments are conducted. A full central bank policy model is derived that includes the Taylor condition along with equations comparable to the standard aggregate-demand/...

Exact sampling from conditional Boolean models with applications to maximum likelihood inference

NARCIS (Netherlands)

Lieshout, van M.N.M.; Zwet, van E.W.

2001-01-01

We are interested in estimating the intensity parameter of a Boolean model of discs (the bombing model) from a single realization. To do so, we derive the conditional distribution of the points (germs) of the underlying Poisson process. We demonstrate how to apply coupling from the past to generate

Conditional Random Fields versus Hidden Markov Models for activity recognition in temporal sensor data

NARCIS (Netherlands)

van Kasteren, T.L.M.; Noulas, A.K.; Kröse, B.J.A.; Smit, G.J.M.; Epema, D.H.J.; Lew, M.S.

2008-01-01

Conditional Random Fields are a discriminative probabilistic model which recently gained popularity in applications that require modeling nonindependent observation sequences. In this work, we present the basic advantages of this model over generative models and argue about its suitability in the

A Bayesian localized conditional autoregressive model for estimating the health effects of air pollution.

Science.gov (United States)

Lee, Duncan; Rushworth, Alastair; Sahu, Sujit K

2014-06-01

Estimation of the long-term health effects of air pollution is a challenging task, especially when modeling spatial small-area disease incidence data in an ecological study design. The challenge comes from the unobserved underlying spatial autocorrelation structure in these data, which is accounted for using random effects modeled by a globally smooth conditional autoregressive model. These smooth random effects confound the effects of air pollution, which are also globally smooth. To avoid this collinearity a Bayesian localized conditional autoregressive model is developed for the random effects. This localized model is flexible spatially, in the sense that it is not only able to model areas of spatial smoothness, but also it is able to capture step changes in the random effects surface. This methodological development allows us to improve the estimation performance of the covariate effects, compared to using traditional conditional auto-regressive models. These results are established using a simulation study, and are then illustrated with our motivating study on air pollution and respiratory ill health in Greater Glasgow, Scotland in 2011. The model shows substantial health effects of particulate matter air pollution and nitrogen dioxide, whose effects have been consistently attenuated by the currently available globally smooth models. © 2014, The Authors Biometrics published by Wiley Periodicals, Inc. on behalf of International Biometric Society.

A Methodological Demonstration of Set-theoretical Approach to Social Media Maturity Models Using Necessary Condition Analysis

DEFF Research Database (Denmark)

Lasrado, Lester Allan; Vatrapu, Ravi; Andersen, Kim Normann

2016-01-01

Despite being widely accepted and applied across research domains, maturity models have been criticized for lacking academic rigor, especially methodologically rigorous and empirically grounded or tested maturity models are quite rare. Attempting to close this gap, we adopt a set-theoretic approach...... and evaluate some of arguments presented by previous conceptual focused social media maturity models....... by applying the Necessary Condition Analysis (NCA) technique to derive maturity stages and stage boundaries conditions. The ontology is to view stages (boundaries) in maturity models as a collection of necessary condition. Using social media maturity data, we demonstrate the strength of our approach...

Consistent initial conditions for the Saint-Venant equations in river network modeling

Directory of Open Access Journals (Sweden)

C.-W. Yu

2017-09-01

Full Text Available Initial conditions for flows and depths (cross-sectional areas throughout a river network are required for any time-marching (unsteady solution of the one-dimensional (1-D hydrodynamic Saint-Venant equations. For a river network modeled with several Strahler orders of tributaries, comprehensive and consistent synoptic data are typically lacking and synthetic starting conditions are needed. Because of underlying nonlinearity, poorly defined or inconsistent initial conditions can lead to convergence problems and long spin-up times in an unsteady solver. Two new approaches are defined and demonstrated herein for computing flows and cross-sectional areas (or depths. These methods can produce an initial condition data set that is consistent with modeled landscape runoff and river geometry boundary conditions at the initial time. These new methods are (1 the pseudo time-marching method (PTM that iterates toward a steady-state initial condition using an unsteady Saint-Venant solver and (2 the steady-solution method (SSM that makes use of graph theory for initial flow rates and solution of a steady-state 1-D momentum equation for the channel cross-sectional areas. The PTM is shown to be adequate for short river reaches but is significantly slower and has occasional non-convergent behavior for large river networks. The SSM approach is shown to provide a rapid solution of consistent initial conditions for both small and large networks, albeit with the requirement that additional code must be written rather than applying an existing unsteady Saint-Venant solver.

A robust model predictive control strategy for improving the control performance of air-conditioning systems

International Nuclear Information System (INIS)

Huang Gongsheng; Wang Shengwei; Xu Xinhua

2009-01-01

This paper presents a robust model predictive control strategy for improving the supply air temperature control of air-handling units by dealing with the associated uncertainties and constraints directly. This strategy uses a first-order plus time-delay model with uncertain time-delay and system gain to describe air-conditioning process of an air-handling unit usually operating at various weather conditions. The uncertainties of the time-delay and system gain, which imply the nonlinearities and the variable dynamic characteristics, are formulated using an uncertainty polytope. Based on this uncertainty formulation, an offline LMI-based robust model predictive control algorithm is employed to design a robust controller for air-handling units which can guarantee a good robustness subject to uncertainties and constraints. The proposed robust strategy is evaluated in a dynamic simulation environment of a variable air volume air-conditioning system in various operation conditions by comparing with a conventional PI control strategy. The robustness analysis of both strategies under different weather conditions is also presented.

Modeling speech intelligibility in adverse conditions

DEFF Research Database (Denmark)

Dau, Torsten

2012-01-01

) in conditions with nonlinearly processed speech. Instead of considering the reduction of the temporal modulation energy as the intelligibility metric, as assumed in the STI, the sEPSM applies the signal-to-noise ratio in the envelope domain (SNRenv). This metric was shown to be the key for predicting...... understanding speech when more than one person is talking, even when reduced audibility has been fully compensated for by a hearing aid. The reasons for these difficulties are not well understood. This presentation highlights recent concepts of the monaural and binaural signal processing strategies employed...... by the normal as well as impaired auditory system. Jørgensen and Dau [(2011). J. Acoust. Soc. Am. 130, 1475-1487] proposed the speech-based envelope power spectrum model (sEPSM) in an attempt to overcome the limitations of the classical speech transmission index (STI) and speech intelligibility index (SII...

Information about the model's unconditioned stimulus and response in vicarious classical conditioning.

Science.gov (United States)

Hygge, S

1976-06-01

Four groups with 16 observers each participated in a differential, vicarious conditioning experiment with skin conductance responses as the dependent variable. The information available to the observer about the model's unconditioned stimulus and response was varied in a 2 X 2 factorial design. Results clearly showed that information about the model's unconditioned stimulus (a high or low dB level) was not necessary for vicarious instigation, but that information about the unconditioned response (a high or low emotional aversiveness) was necessary. Data for conditioning of responses showed almost identical patterns to those for vicarious instigation. To explain the results, a distinction between factors necessary for the development and elicitation of vicariously instigated responses was introduced, and the effectiveness of information about the model's response on the elicitation of vicariously instigated responses was considered in terms of an expansion of Bandura's social learning theory.

A Modelling Framework to Assess the Effect of Pressures on River Abiotic Habitat Conditions and Biota.

Directory of Open Access Journals (Sweden)

Jochem Kail

Full Text Available River biota are affected by global reach-scale pressures, but most approaches for predicting biota of rivers focus on river reach or segment scale processes and habitats. Moreover, these approaches do not consider long-term morphological changes that affect habitat conditions. In this study, a modelling framework was further developed and tested to assess the effect of pressures at different spatial scales on reach-scale habitat conditions and biota. Ecohydrological and 1D hydrodynamic models were used to predict discharge and water quality at the catchment scale and the resulting water level at the downstream end of a study reach. Long-term reach morphology was modelled using empirical regime equations, meander migration and 2D morphodynamic models. The respective flow and substrate conditions in the study reach were predicted using a 2D hydrodynamic model, and the suitability of these habitats was assessed with novel habitat models. In addition, dispersal models for fish and macroinvertebrates were developed to assess the re-colonization potential and to finally compare habitat suitability and the availability/ability of species to colonize these habitats. Applicability was tested and model performance was assessed by comparing observed and predicted conditions in the lowland Treene River in northern Germany. Technically, it was possible to link the different models, but future applications would benefit from the development of open source software for all modelling steps to enable fully automated model runs. Future research needs concern the physical modelling of long-term morphodynamics, feedback of biota (e.g., macrophytes on abiotic habitat conditions, species interactions, and empirical data on the hydraulic habitat suitability and dispersal abilities of macroinvertebrates. The modelling framework is flexible and allows for including additional models and investigating different research and management questions, e.g., in climate impact

Boundary conditions for plasma fluid models at the magnetic presheath entrance

International Nuclear Information System (INIS)

Loizu, J.; Ricci, P.; Halpern, F. D.; Jolliet, S.

2012-01-01

The proper boundary conditions at the magnetic presheath entrance for plasma fluid turbulence models based on the drift approximation are derived, focusing on a weakly collisional plasma sheath with T i ≪T e and a magnetic field oblique to a totally absorbing wall. First, the location of the magnetic presheath entrance is rigorously derived. Then boundary conditions at the magnetic presheath entrance are analytically deduced for v ||i , v ||e , n, φ, T e , and for the vorticity ω=∇ ⊥ 2 φ. The effects of E × B and diamagnetic drifts on the boundary conditions are also investigated. Kinetic simulations are performed that confirm the analytical results. Finally, the new set of boundary conditions is implemented in a three-dimensional global fluid code for the simulation of plasma turbulence and, as an example, the results of a tokamak scrape-off layer simulation are discussed. The framework presented can be generalized to obtain boundary conditions at the magnetic presheath entrance in more complex scenarios.

76 FR 62661 - Airworthiness Directives; The Boeing Company Model 767-200 and -300 Series Airplanes

Science.gov (United States)

2011-10-11

...-766-5680; e-mail: [email protected] ; Internet: https://www.myboeingfleet.com . You may review...- 3356; phone: 425-917-6596; fax: 425-917-6590; e-mail: [email protected] . SUPPLEMENTARY INFORMATION... Transport Association (ATA) of America Code 25: Equipment and Furnishings. Unsafe Condition (e) This AD was...

Modelling thermomechanical conditions at the tool/matrix interface in Friction Stir Welding

DEFF Research Database (Denmark)

Schmidt, Henrik Nikolaj Blich; Hattel, Jesper

2004-01-01

is obtained. A fully coupled thermo-mechanical 3D FE model has been developed in ABAQUS/Explicit using the ALE formulation and the Johnson-Cook material law. The contact forces are modelled by Coulomb’s law of friction making the contact condition highly solution dependent. The heat is generated by both...

ADAPTATION OF WOFOST MODEL FROM CGMS TO ROMANIAN CONDITIONS

Directory of Open Access Journals (Sweden)

LAZĂR CĂTĂLIN

2009-12-01

Full Text Available This preliminary study is an inventory of the main resources and difficulties in adaptation of the Crop Growth Monitoring System (CGMS used by Agri4cast unit of IPSC from Joint Research Centre (JRC - Ispra of European Commission to conditions of Romania.In contrast with the original model calibrated mainly with statistical average yields at national level, for local calibration of the model the statistical yields at lower administrative units (macroregion or county must be used. In addition, for winter crops, the start of simulation in the new system will be in the autumn of the previous year. The start of simulation (and emergence day in the genuine system is 1st of January of the current year and the existing calibration was meant to provide a compensation system for this technical physiological delay.Proposed approach provides a better initialisation of the water balance (emergence occurs after start of simulation, as well as a better account for impact of wintering conditions, but obviously a new calibration for all cultivar dependent parameters is necessary. For the preoperational run, the localized model will use the weather data available till the last day available and the missing data from the rest of the year will be replaced either by the daily values of the long term averages or by the values from a year considered similar with the current one.Proposed adaptations permit a better use of information available on local scale and the localized model may be the core of a regional system for crop monitoring and in the same degree as the original system it can be used as tool for specific researches, such as studying the impact of climate changes.

The conditional moment closure method for modeling lean premixed turbulent combustion

Science.gov (United States)

Martin, Scott Montgomery

Natural gas fired lean premixed gas turbines have become the method of choice for new power generation systems due to their high efficiency and low pollutant emissions. As emission regulations for these combustion systems become more stringent, the use of numerical modeling has become an important a priori tool in designing clean and efficient combustors. Here a new turbulent combustion model is developed in an attempt to improve the state of the art. The Conditional Moment Closure (CMC) method is a new theory that has been applied to non-premixed combustion with good success. The application of the CMC method to premixed systems has been proposed, but has not yet been done. The premixed CMC method replaces the species mass fractions as independent variables with the species mass fractions that are conditioned on a reaction progress variable (RPV). Conservation equations for these new variables are then derived and solved. The general idea behind the CMC method is that the behavior of the chemical species is closely coupled to the reaction progress variable. Thus, species conservation equations that are conditioned on the RPV will have terms involving the fluctuating quantities that are much more likely to be negligible. The CMC method accounts for the interaction between scalar dissipation (micromixing) and chemistry, while de-coupling the kinetics from the bulk flow (macromixing). Here the CMC method is combined with a commercial computational fluid dynamics program, which calculates the large-scale fluid motions. The CMC model is validated by comparison to 2-D reacting backward facing step data. Predicted species, temperature and velocity fields are compared to experimental data with good success. The CMC model is also validated against the University of Washington's 3-D jet stirred reactor (JSR) data, which is an idealized lean premixed combustor. The JSR results are encouraging, but not as good as the backward facing step. The largest source of error is from

Estimation of value at risk and conditional value at risk using normal mixture distributions model

Science.gov (United States)

Kamaruzzaman, Zetty Ain; Isa, Zaidi

2013-04-01

Normal mixture distributions model has been successfully applied in financial time series analysis. In this paper, we estimate the return distribution, value at risk (VaR) and conditional value at risk (CVaR) for monthly and weekly rates of returns for FTSE Bursa Malaysia Kuala Lumpur Composite Index (FBMKLCI) from July 1990 until July 2010 using the two component univariate normal mixture distributions model. First, we present the application of normal mixture distributions model in empirical finance where we fit our real data. Second, we present the application of normal mixture distributions model in risk analysis where we apply the normal mixture distributions model to evaluate the value at risk (VaR) and conditional value at risk (CVaR) with model validation for both risk measures. The empirical results provide evidence that using the two components normal mixture distributions model can fit the data well and can perform better in estimating value at risk (VaR) and conditional value at risk (CVaR) where it can capture the stylized facts of non-normality and leptokurtosis in returns distribution.

Lithium-ion battery dynamic model for wide range of operating conditions

DEFF Research Database (Denmark)

Stroe, Ana-Irina; Stroe, Daniel-Ioan; Swierczynski, Maciej Jozef

2017-01-01

In order to analyze the dynamic behavior of a Lithium-ion (Li-ion) battery and to determine their suitability for various applications, battery models are needed. An equivalent electrical circuit model is the most common way of representing the behavior of a Li-ion battery. There are different...... characterization tests performed for a wide range of operating conditions (temperature, load current and state-of-charge) on a commercial available 13Ah high-power lithium titanate oxide battery cell. The obtained results were used to parametrize the proposed dynamic model of the battery cell. To assess...

A model for determining condition-based maintenance policies for deteriorating multi-component systems

NARCIS (Netherlands)

Hontelez, J.A.M.; Wijnmalen, D.J.D.

1993-01-01

We discuss a method to determine strategies for preventive maintenance of systems consisting of gradually deteriorating components. A model has been developed to compute not only the range of conditions inducing a repair action, but also inspection moments based on the last known condition value so

Influence of model boundary conditions on blood flow patterns in a patient specific stenotic right coronary artery.

Science.gov (United States)

Liu, Biyue; Zheng, Jie; Bach, Richard; Tang, Dalin

2015-01-01

In literature, the effect of the inflow boundary condition was investigated by examining the impact of the waveform and the shape of the spatial profile of the inlet velocity on the cardiac hemodynamics. However, not much work has been reported on comparing the effect of the different combinations of the inlet/outlet boundary conditions on the quantification of the pressure field and flow distribution patterns in stenotic right coronary arteries. Non-Newtonian models were used to simulate blood flow in a patient-specific stenotic right coronary artery and investigate the influence of different boundary conditions on the phasic variation and the spatial distribution patterns of blood flow. The 3D geometry of a diseased artery segment was reconstructed from a series of IVUS slices. Five different combinations of the inlet and the outlet boundary conditions were tested and compared. The temporal distribution patterns and the magnitudes of the velocity, the wall shear stress (WSS), the pressure, the pressure drop (PD), and the spatial gradient of wall pressure (WPG) were different when boundary conditions were imposed using different pressure/velocity combinations at inlet/outlet. The maximum velocity magnitude in a cardiac cycle at the center of the inlet from models with imposed inlet pressure conditions was about 29% lower than that from models using fully developed inlet velocity data. Due to the fact that models with imposed pressure conditions led to blunt velocity profile, the maximum wall shear stress at inlet in a cardiac cycle from models with imposed inlet pressure conditions was about 29% higher than that from models with imposed inlet velocity boundary conditions. When the inlet boundary was imposed by a velocity waveform, the models with different outlet boundary conditions resulted in different temporal distribution patterns and magnitudes of the phasic variation of pressure. On the other hand, the type of different boundary conditions imposed at the

NIR Color vs Launch Date: A 20-Year Analysis of Space Weathering Effects on the Boeing 376 Spacecraft

Science.gov (United States)

Frith, James; Anz-Meador, Philip; Lederer, Sue; Cowardin, Heather; Buckalew, Brent

2015-01-01

The Boeing HS-376 spin stabilized spacecraft was a popular design that was launched continuously into geosynchronous orbit starting in 1980 with the last launch occurring in 2002. Over 50 of the HS-376 buses were produced to fulfill a variety of different communication missions for countries all over the world. The design of the bus is easily approximated as a telescoping cylinder that is covered with solar cells and an Earth facing antenna that is despun at the top of the cylinder. The similarity in design and the number of spacecraft launched over a long period of time make the HS-376 a prime target for studying the effects of solar weathering on solar panels as a function of time. A selection of primarily non-operational HS-376 spacecraft launched over a 20 year time period were observed using the United Kingdom Infrared Telescope on Mauna Kea and multi-band near-infrared photometry produced. Each spacecraft was observed for an entire night cycling through ZYJHK filters and time-varying colors produced to compare near-infrared color as a function of launch date. The resulting analysis shown here may help in the future to set launch date constraints on the parent object of unidentified debris objects or other unknown spacecraft.

Modeling activities in air traffic control systems: antecedents and consequences of a mid-air collision.

Science.gov (United States)

de Carvalho, Paulo Victor R; Ferreira, Bemildo

2012-01-01

In this article we present a model of some functions and activities of the Brazilian Air traffic Control System (ATS) in the period in which occurred a mid-air collision between flight GLO1907, a commercial aircraft Boeing 737-800, and flight N600XL, an executive jet EMBRAER E-145, to investigate key resilience characteristics of the ATM. Modeling in some detail activities during the collision and related them to overall behavior and antecedents that stress the organization uncover some drift into failure mechanisms that erode safety defenses provided by the Air Navigation Service Provider (ANSP), enabling a mid-air collision to be happen.

Model Development for Risk Assessment of Driving on Freeway under Rainy Weather Conditions.

Directory of Open Access Journals (Sweden)

Xiaonan Cai

Full Text Available Rainy weather conditions could result in significantly negative impacts on driving on freeways. However, due to lack of enough historical data and monitoring facilities, many regions are not able to establish reliable risk assessment models to identify such impacts. Given the situation, this paper provides an alternative solution where the procedure of risk assessment is developed based on drivers' subjective questionnaire and its performance is validated by using actual crash data. First, an ordered logit model was developed, based on questionnaire data collected from Freeway G15 in China, to estimate the relationship between drivers' perceived risk and factors, including vehicle type, rain intensity, traffic volume, and location. Then, weighted driving risk for different conditions was obtained by the model, and further divided into four levels of early warning (specified by colors using a rank order cluster analysis. After that, a risk matrix was established to determine which warning color should be disseminated to drivers, given a specific condition. Finally, to validate the proposed procedure, actual crash data from Freeway G15 were compared with the safety prediction based on the risk matrix. The results show that the risk matrix obtained in the study is able to predict driving risk consistent with actual safety implications, under rainy weather conditions.

Physical robustness of canopy temperature models for crop heat stress simulation across environments and production conditions

DEFF Research Database (Denmark)

Webber, Heidi; White, Jeffrey W; Kimball, Bruce

2018-01-01

to simulate Tc. Model performance in predicting Tc was evaluated for two experiments in continental North America with various water, nitrogen and CO2 treatments. An empirical model fit to one dataset had the best performance, followed by the EBSC models. Stability conditions explained much of the differences...... between modeling approaches. More accurate simulation of heat stress will likely require use of energy balance approaches that consider atmospheric stability conditions....

On the identification of fractionally cointegrated VAR models with the F(d) condition

DEFF Research Database (Denmark)

Carlini, Federico; Santucci de Magistris, Paolo

with different fractional integration and cointegration parameters. The properties of these multiple non-identified sub-models are studied and a necessary and sufficient condition for the identification of the fractional parameters of the system is provided. The condition is named F(d). The assessment of the F(d...

78 FR 76254 - Special Conditions: Airbus, Model A350-900 Series Airplane; Control Surface Awareness and Mode...

Science.gov (United States)

2013-12-17

...-0899; Notice No. 25-13-15-SC] Special Conditions: Airbus, Model A350-900 Series Airplane; Control... of proposed special conditions. SUMMARY: This action proposes special conditions for the Airbus Model..., data, or views. The most helpful comments reference a specific portion of the proposed special...

Exponential model normalization for electrical capacitance tomography with external electrodes under gap permittivity conditions

International Nuclear Information System (INIS)

Baidillah, Marlin R; Takei, Masahiro

2017-01-01

A nonlinear normalization model which is called exponential model for electrical capacitance tomography (ECT) with external electrodes under gap permittivity conditions has been developed. The exponential model normalization is proposed based on the inherently nonlinear relationship characteristic between the mixture permittivity and the measured capacitance due to the gap permittivity of inner wall. The parameters of exponential equation are derived by using an exponential fitting curve based on the simulation and a scaling function is added to adjust the experiment system condition. The exponential model normalization was applied to two dimensional low and high contrast dielectric distribution phantoms by using simulation and experimental studies. The proposed normalization model has been compared with other normalization models i.e. Parallel, Series, Maxwell and Böttcher models. Based on the comparison of image reconstruction results, the exponential model is reliable to predict the nonlinear normalization of measured capacitance in term of low and high contrast dielectric distribution. (paper)

Communication: modeling charge-sign asymmetric solvation free energies with nonlinear boundary conditions.

Science.gov (United States)

Bardhan, Jaydeep P; Knepley, Matthew G

2014-10-07

We show that charge-sign-dependent asymmetric hydration can be modeled accurately using linear Poisson theory after replacing the standard electric-displacement boundary condition with a simple nonlinear boundary condition. Using a single multiplicative scaling factor to determine atomic radii from molecular dynamics Lennard-Jones parameters, the new model accurately reproduces MD free-energy calculations of hydration asymmetries for: (i) monatomic ions, (ii) titratable amino acids in both their protonated and unprotonated states, and (iii) the Mobley "bracelet" and "rod" test problems [D. L. Mobley, A. E. Barber II, C. J. Fennell, and K. A. Dill, "Charge asymmetries in hydration of polar solutes," J. Phys. Chem. B 112, 2405-2414 (2008)]. Remarkably, the model also justifies the use of linear response expressions for charging free energies. Our boundary-element method implementation demonstrates the ease with which other continuum-electrostatic solvers can be extended to include asymmetry.

Communication: Modeling charge-sign asymmetric solvation free energies with nonlinear boundary conditions

International Nuclear Information System (INIS)

Bardhan, Jaydeep P.; Knepley, Matthew G.

2014-01-01

We show that charge-sign-dependent asymmetric hydration can be modeled accurately using linear Poisson theory after replacing the standard electric-displacement boundary condition with a simple nonlinear boundary condition. Using a single multiplicative scaling factor to determine atomic radii from molecular dynamics Lennard-Jones parameters, the new model accurately reproduces MD free-energy calculations of hydration asymmetries for: (i) monatomic ions, (ii) titratable amino acids in both their protonated and unprotonated states, and (iii) the Mobley “bracelet” and “rod” test problems [D. L. Mobley, A. E. Barber II, C. J. Fennell, and K. A. Dill, “Charge asymmetries in hydration of polar solutes,” J. Phys. Chem. B 112, 2405–2414 (2008)]. Remarkably, the model also justifies the use of linear response expressions for charging free energies. Our boundary-element method implementation demonstrates the ease with which other continuum-electrostatic solvers can be extended to include asymmetry

Communication: Modeling charge-sign asymmetric solvation free energies with nonlinear boundary conditions

Energy Technology Data Exchange (ETDEWEB)

Bardhan, Jaydeep P. [Department of Mechanical and Industrial Engineering, Northeastern University, Boston, Massachusetts 02115 (United States); Knepley, Matthew G. [Computation Institute, The University of Chicago, Chicago, Illinois 60637 (United States)

2014-10-07

We show that charge-sign-dependent asymmetric hydration can be modeled accurately using linear Poisson theory after replacing the standard electric-displacement boundary condition with a simple nonlinear boundary condition. Using a single multiplicative scaling factor to determine atomic radii from molecular dynamics Lennard-Jones parameters, the new model accurately reproduces MD free-energy calculations of hydration asymmetries for: (i) monatomic ions, (ii) titratable amino acids in both their protonated and unprotonated states, and (iii) the Mobley “bracelet” and “rod” test problems [D. L. Mobley, A. E. Barber II, C. J. Fennell, and K. A. Dill, “Charge asymmetries in hydration of polar solutes,” J. Phys. Chem. B 112, 2405–2414 (2008)]. Remarkably, the model also justifies the use of linear response expressions for charging free energies. Our boundary-element method implementation demonstrates the ease with which other continuum-electrostatic solvers can be extended to include asymmetry.

Crack propagation rate modelling for 316SS exposed to PWR-relevant conditions

International Nuclear Information System (INIS)

Vankeerberghen, M.; Weyns, G.; Gavrilov, S.; Martens, B.; Deconinck, J.

2009-01-01

The crack propagation rate of Type 316 stainless steel in boric acid-lithium hydroxide solutions under PWR-relevant conditions was modelled. A film rupture/dissolution/repassivation mechanism is assumed and extended to cold worked materials by including a stress-dependent bare metal dissolution current density. The chemical and electrochemical conditions within the crack are calculated by finite element calculations, an analytical expression is used for the crack-tip strain rate and the crack-tip stress is assumed equal to 2.5 times the yield stress (plane-strain). First the model was calibrated against a literature published data set. Afterwards, the influence of various variables - dissolved hydrogen, boric acid and lithium hydroxide content, stress intensity, crack length, temperature, flow rate - was studied. Finally, other published crack growth rate tests were modelled and the calculated crack growth rates were found to be in reasonable agreement with the reported ones

Ageing model considering effects of maintenance and working conditions

International Nuclear Information System (INIS)

Martorell, S.; Sanchez, A.; Serradell, V.

1998-01-01

Nowadays, there is some doubt about building new Nuclear Power Plants (NPPs). Instead, there is a growing interest in analyzing the possibility to extend current NPP operation where life management programs play an important role. The evolution of the NPP safety depends on the evolution of the reliability of its safety components as a function of their age along the NPP operational life. In this paper, a new age-dependent reliability model is presented, which includes parameters related to surveillance and maintenance effectiveness and working conditions, both environmental and operational, of the equipment. This model may be used to support NPP life management and life extension programs by improving or optimizing surveillance and maintenance tasks using risk and cost models based on such an age-dependent reliability model. The results of the sensitivity study in the application show that the selection of the most appropriate maintenance strategy would directly depend on the previous parameters and very important differences are expected to appear under certain circumstance. (Author) 7 refs

A Markov switching model of the conditional volatility of crude oil futures prices

International Nuclear Information System (INIS)

Fong, Wai Mun; See, Kim Hock

2002-01-01

This paper examines the temporal behaviour of volatility of daily returns on crude oil futures using a generalised regime switching model that allows for abrupt changes in mean and variance, GARCH dynamics, basis-driven time-varying transition probabilities and conditional leptokurtosis. This flexible model enables us to capture many complex features of conditional volatility within a relatively parsimonious set-up. We show that regime shifts are clearly present in the data and dominate GARCH effects. Within the high volatility state, a negative basis is more likely to increase regime persistence than a positive basis, a finding which is consistent with previous empirical research on the theory of storage. The volatility regimes identified by our model correlate well with major events affecting supply and demand for oil. Out-of-sample tests indicate that the regime switching model performs noticeably better than non-switching models regardless of evaluation criteria. We conclude that regime switching models provide a useful framework for the financial historian interested in studying factors behind the evolution of volatility and to oil futures traders interested short-term volatility forecasts

Model Based Optimal Sensor Network Design for Condition Monitoring in an IGCC Plant

Energy Technology Data Exchange (ETDEWEB)

Kumar, Rajeeva; Kumar, Aditya; Dai, Dan; Seenumani, Gayathri; Down, John; Lopez, Rodrigo

2012-12-31

This report summarizes the achievements and final results of this program. The objective of this program is to develop a general model-based sensor network design methodology and tools to address key issues in the design of an optimal sensor network configuration: the type, location and number of sensors used in a network, for online condition monitoring. In particular, the focus in this work is to develop software tools for optimal sensor placement (OSP) and use these tools to design optimal sensor network configuration for online condition monitoring of gasifier refractory wear and radiant syngas cooler (RSC) fouling. The methodology developed will be applicable to sensing system design for online condition monitoring for broad range of applications. The overall approach consists of (i) defining condition monitoring requirement in terms of OSP and mapping these requirements in mathematical terms for OSP algorithm, (ii) analyzing trade-off of alternate OSP algorithms, down selecting the most relevant ones and developing them for IGCC applications (iii) enhancing the gasifier and RSC models as required by OSP algorithms, (iv) applying the developed OSP algorithm to design the optimal sensor network required for the condition monitoring of an IGCC gasifier refractory and RSC fouling. Two key requirements for OSP for condition monitoring are desired precision for the monitoring variables (e.g. refractory wear) and reliability of the proposed sensor network in the presence of expected sensor failures. The OSP problem is naturally posed within a Kalman filtering approach as an integer programming problem where the key requirements of precision and reliability are imposed as constraints. The optimization is performed over the overall network cost. Based on extensive literature survey two formulations were identified as being relevant to OSP for condition monitoring; one based on LMI formulation and the other being standard INLP formulation. Various algorithms to solve

A mathematical model for localized corrosion in steam generator crevices under heat transfer conditions

International Nuclear Information System (INIS)

Engelhardt, G.; Urquidi-Macdonald, M.; Sikora, J.; Macdonald, D.D.

1995-01-01

A predictive and self-consistent mathematical model has been developed to describe the localized corrosion in steam generators. The model recognizes that the internal and external environment are coupled by the need to conserve charge in the system. Thus, solution of Laplace's equation for the external environment (outside the crevice) provides the boundary condition for the electric potential at the crevice mouth, which is needed for solving the system of mass transfer equations for the internal environment (inside the crevice). Mass transfer by diffusion, ion migration, and convection was considered. Heat and momentum transfer equations are solved simultaneously, with the mass balance equation for each species and the condition of electroneutrality inside the cavity being considered. The model takes into account the porosity and tortuosity in the corrosion product deposit in the crevice. The homogeneous chemical reactions (hydrolysis of the products of the anodic reaction and the autoprotolysis of water) are included in the model. The model, in this preliminary form predicts the solution chemistry, potential drop, and temperature distribution inside the crevice. An order of magnitude estimate of the crevice corrosion rate also obtained. At this point, the model predicts only the steady state solution, but it is recognized that a steady state may not exist under normal conditions

76 FR 65105 - Special Conditions: Gulfstream Aerospace Corporation, Model GIV-X Airplane; Isolation or Aircraft...

Science.gov (United States)

2011-10-20

...-1140; Special Conditions No. 25-450-SC] Special Conditions: Gulfstream Aerospace Corporation, Model GIV-X Airplane; Isolation or Aircraft Electronic System Security Protection From Unauthorized Internal Access AGENCY: Federal Aviation Administration (FAA), DOT. ACTION: Final special conditions; request for...

OUTSOURCING NEW PRODUCT DEVELOPMENT FOSTERED BY DISRUPTIVE TECHNOLOGICAL INNOVATION

DEFF Research Database (Denmark)

CANTONE, LUIGI; TESTA, PIERPAOLO; HOLLENSEN, SVEND

2018-01-01

is that of aircraft industry. Therefore, this article discusses the findings of an empirical research that explores an embedded and in-depth longitudinal case study, namely, the Boeing 787-8 programme (the first model of the B787 Dreamliner programme). This new aircraft is a disruptive technology product innovation...... outsourcing strategies related to the Boeing 787 Dreamliner programme. The research question that we aim to answer is: which strategic dimensions in a decision-making model are able to extensively and thoroughly address the outsourcing decisions relating to NPD activities given the hypothesis...

Soot Formation Modeling of n-dodecane and Diesel Sprays under Engine-Like Conditions

DEFF Research Database (Denmark)

Pang, Kar Mun; Poon, Hiew Mun; Ng, Hoon Kiat

2015-01-01

This work concerns the modelling of soot formation process in diesel spray combustion under engine-like conditions. The key aim is to investigate the soot formation characteristics at different ambient temperatures. Prior to simulating the diesel combustion, numerical models including a revised...

Comprehensive oral-health assessment of individuals with acquired brain-injury in neuro-rehabilitation setting.

Science.gov (United States)

Kothari, Mohit; Spin-Neto, Rubens; Nielsen, Jørgen Feldbæk

2016-01-01

To perform a detailed clinical oral health assessment and oral-health-related social and behavioural aspect assessment in individuals with acquired brain injury (ABI). Prospective observational study. Thirteen individuals with ABI were recruited. Individual's social and behavioural history, bed-side oral examination score (BOE), tooth condition and periodontal status (bleeding, plaque and clinical attachment loss) were thoroughly examined. The entire examination took up to 60 minutes, using proper dental armamentarium. All evaluated individuals were diagnosed with chronic generalized periodontitis. A relationship between active periodontal disease and severe BOE score was observed (p = 0.01). Significant interaction between severe BOE scores (≥ 15 or ≥ 14) and periodontal disease severity of ≥ 2 mm (p = 0.01) was observed. The same interaction was seen between severe BOE scores and the combination of 75% extent and 2 mm severity (p = 0.01). Severity and activity of periodontitis showed dependence on individual brushing frequency (p = 0.03 and p = 0.05, respectively). Individuals with ABI had a poor status across a range of oral-, dental- and periodontal-related parameters. Further structured studies are required to define evidence-based assessment approaches for such clinical reality.

Model Forecast Skill and Sensitivity to Initial Conditions in the Seasonal Sea Ice Outlook

Science.gov (United States)

Blanchard-Wrigglesworth, E.; Cullather, R. I.; Wang, W.; Zhang, J.; Bitz, C. M.

2015-01-01

We explore the skill of predictions of September Arctic sea ice extent from dynamical models participating in the Sea Ice Outlook (SIO). Forecasts submitted in August, at roughly 2 month lead times, are skillful. However, skill is lower in forecasts submitted to SIO, which began in 2008, than in hindcasts (retrospective forecasts) of the last few decades. The multimodel mean SIO predictions offer slightly higher skill than the single-model SIO predictions, but neither beats a damped persistence forecast at longer than 2 month lead times. The models are largely unsuccessful at predicting each other, indicating a large difference in model physics and/or initial conditions. Motivated by this, we perform an initial condition sensitivity experiment with four SIO models, applying a fixed -1 m perturbation to the initial sea ice thickness. The significant range of the response among the models suggests that different model physics make a significant contribution to forecast uncertainty.

Wind turbine condition monitoring based on SCADA data using normal behavior models

DEFF Research Database (Denmark)

Schlechtingen, Meik; Santos, Ilmar; Achiche, Sofiane

2013-01-01

This paper proposes a system for wind turbine condition monitoring using Adaptive Neuro-Fuzzy Interference Systems (ANFIS). For this purpose: (1) ANFIS normal behavior models for common Supervisory Control And Data Acquisition (SCADA) data are developed in order to detect abnormal behavior...... the applicability of ANFIS models for monitoring wind turbine SCADA signals. The computational time needed for model training is compared to Neural Network (NN) models showing the strength of ANFIS in training speed. (2) For automation of fault diagnosis Fuzzy Interference Systems (FIS) are used to analyze...

Implementation and Testing of Advanced Surface Boundary Conditions Over Complex Terrain in A Semi-idealized Model

Science.gov (United States)

Li, Y.; Epifanio, C.

2017-12-01

In numerical prediction models, the interaction between the Earth's surface and the atmosphere is typically accounted for in terms of surface layer parameterizations, whose main job is to specify turbulent fluxes of heat, moisture and momentum across the lower boundary of the model domain. In the case of a domain with complex geometry, implementing the flux conditions (particularly the tensor stress condition) at the boundary can be somewhat subtle, and there has been a notable history of confusion in the CFD community over how to formulate and impose such conditions generally. In the atmospheric case, modelers have largely been able to avoid these complications, at least until recently, by assuming that the terrain resolved at typical model resolutions is fairly gentle, in the sense of having relatively shallow slopes. This in turn allows the flux conditions to be imposed as if the lower boundary were essentially flat. Unfortunately, while this flat-boundary assumption is acceptable for coarse resolutions, as grids become more refined and the geometry of the resolved terrain becomes more complex, the appproach is less justified. With this in mind, the goal of our present study is to explore the implementation and usage of the full, unapproximated version of the turbulent flux/stress conditions in atmospheric models, thus taking full account of the complex geometry of the resolved terrain. We propose to implement the conditions using a semi-idealized model developed by Epifanio (2007), in which the discretized boundary conditions are reduced to a large, sparse-matrix problem. The emphasis will be on fluxes of momentum, as the tensor nature of this flux makes the associated stress condition more difficult to impose, although the flux conditions for heat and moisture will be considered as well. With the resulotion of 90 meters, some of the results show that the typical differences between flat-boundary cases and full/stress cases are on the order of 10%, with extreme

Global Aerospace Industries: Rapid Changes Ahead? (Abridged)

Science.gov (United States)

2012-04-30

Understanding the Situation: Contestable Markets • Central idea: the extent to which markets are “contestable” causes monopolists and oligopolists to behave...find useful explanatory models for Boeing?s success, discussed in Chapter II. In Chapter III, we consider the narrow-body airliner market , currently...families have provided resources for a number of wide-body developments some of which have become part of the defense marketplace. The narrow-body market

Modelling and simulation of concrete leaching under outdoor exposure conditions

International Nuclear Information System (INIS)

Schiopu, Nicoleta; Tiruta-Barna, Ligia; Jayr, Emmanuel; Mehu, Jacques; Moszkowicz, Pierre

2009-01-01

Recently, a demand regarding the assessment of release of dangerous substances from construction products was raised by European Commission which has issued the Mandate M/366 addressed to CEN. This action is in relation with the Essential Requirement No. 3 'Hygiene, Health and Environment' of the Construction Products Directive (89/106/EC). The potential hazard for environment and health may arise in different life cycle stages of a construction product. During the service life stage, the release of substances due to contact with the rain water is the main potential hazard source, as a consequence of the leaching phenomenon. The objective of this paper is to present the development of a coupled chemical-transport model for the case of a concrete based construction product, i.e. concrete paving slabs, exposed to rain water under outdoor exposure conditions. The development of the model is based on an iterative process of comparing the experimental results with the simulated results up to an acceptable fit. The experiments were conducted at laboratory scale (equilibrium and dynamic leaching tests) and field scale. The product was exposed for one year in two types of leaching scenarios under outdoor conditions, 'runoff' and 'stagnation', and the element release was monitored. The model was calibrated using the experimental data obtained at laboratory scale and validated against measured field data, by taking into account the specific rain water balance and the atmospheric CO 2 uptake as input parameters. The numerical tool used in order to model and simulate the leaching behaviour was PHREEQC, coupled with the Lawrence Livermore National Laboratory (LLNL) thermodynamic data base. The simulation results are satisfying and the paper demonstrates the feasibility of the modelling approach for the leaching behaviour assessment of concrete type construction materials

76 FR 36390 - Airworthiness Directives; The Boeing Company Model 747SP Series Airplanes

Science.gov (United States)

2011-06-22

... power control modules (PCM). This proposed AD was prompted by a report of a rudder hard-over event on a... rudder PCM manifold, which could result in a hard-over of the rudder surface leading to an increase in... of a Model 747-400 series airplane of a lower rudder hard-over event caused by a lower rudder PCM...

Analysis of the possibility of applying a condition-based maintenance model on an example of tank weapons

Directory of Open Access Journals (Sweden)

Igor J. Epler

2013-12-01

Full Text Available For any modern army it is very important to continuously maintain a high degree of operational (combat readiness (availability in order to maximize the effectiveness of the use of technical systems. Since determination and prediction of technical states and failures of technical systems in engineering, especially in armament, are difficult due to the impossibility of continuous condition monitoring with appropriate measuring equipment there is a need for a maintenance model that would be most helpful in taking timely action maintenance. In this paper, the subject of research is a model of maintenance of the M-84 tank  weapoons systems.   IntroductionThe M-84 tank is one of the most promising technical systems in the Serbian Army. Its use and modifications are foreseen in the next ten years. The  M-84 is characterized by good tactical and technical characteristics. It has a powerful 125 mm cannon, coupled 7.62 mm machine gun and 12.7 mm anti-aircraft machine gun. The M-84 tank has an automatic battery charger and a fire control system. The fire control system enables fast target tracking and stabilization of the cannon barrel, which is a prerequisite for timely and favorable effect on the target. There are certain ambiguities in the existing model of maintenance of tank weapons.   Technical diagnostics Technical diagnostics, as a part of the process of condition-based maintenance, should determine technical conditions of components or technical systems with certain accuracy at a point in time.   Maintenance strategy A maintenance strategy can be defined as a variant of a maintenance system determined by a concept, organization and character of maintenance procedures, as well as the relationship between the various levels at which maintenance is performed. It is defined for technical system parts, individual technical systems and for system maintenance as a whole. The basic maintenance strategies implemented today are: -      corrective

Communication: Modeling charge-sign asymmetric solvation free energies with nonlinear boundary conditions

Science.gov (United States)

Bardhan, Jaydeep P.; Knepley, Matthew G.

2014-01-01

We show that charge-sign-dependent asymmetric hydration can be modeled accurately using linear Poisson theory after replacing the standard electric-displacement boundary condition with a simple nonlinear boundary condition. Using a single multiplicative scaling factor to determine atomic radii from molecular dynamics Lennard-Jones parameters, the new model accurately reproduces MD free-energy calculations of hydration asymmetries for: (i) monatomic ions, (ii) titratable amino acids in both their protonated and unprotonated states, and (iii) the Mobley “bracelet” and “rod” test problems [D. L. Mobley, A. E. Barber II, C. J. Fennell, and K. A. Dill, “Charge asymmetries in hydration of polar solutes,” J. Phys. Chem. B 112, 2405–2414 (2008)]. Remarkably, the model also justifies the use of linear response expressions for charging free energies. Our boundary-element method implementation demonstrates the ease with which other continuum-electrostatic solvers can be extended to include asymmetry. PMID:25296776

Comparison of US/FRG accident condition models for HTGR fuel failure and radionuclide release

International Nuclear Information System (INIS)

Verfondern, K.

1991-03-01

The objective was to compare calculation models used in safety analyses in the US and FRG which describe fission product release behavior from TRISO coated fuel particles under core heatup accident conditions. The frist step performed is the qualitative comparison of both sides' fuel failure and release models in order to identify differences and similarities in modeling assumptions and inputs. Assumptions of possible particle failure mechanisms under accident conditions (SiC degradation, pressure vessel) are principally the same on both sides though they are used in different modeling approaches. The characterization of a standard (= intact) coated particle to be of non-releasing (GA) or possibly releasing (KFA/ISF) type is one of the major qualitative differences. Similar models are used regarding radionuclide release from exposed particle kernels. In a second step, a quantitative comparison of the calculation models was made by assessing a benchmark problem predicting particle failure and radionuclide release under MHTGR conduction cooldown accident conditions. Calculations with each side's reference method have come to almost the same failure fractions after 250 hours for the core region with maximum core heatup temperature despite the different modeling approaches of SORS and PANAMA-I. The comparison of the results of particle failure obtained with the Integrated Failure and Release Model for Standard Particles and its revision provides a 'verification' of these models in this sense that the codes (SORS and PANAMA-II, and -III, respectively) which were independently developed lead to very good agreement in the predictions. (orig./HP) [de

Inference and testing on the boundary in extended constant conditional correlation GARCH models

DEFF Research Database (Denmark)

Pedersen, Rasmus Søndergaard

2017-01-01

We consider inference and testing in extended constant conditional correlation GARCH models in the case where the true parameter vector is a boundary point of the parameter space. This is of particular importance when testing for volatility spillovers in the model. The large-sample properties...

Do simple models give a correct description of the wind condition in a coastal area ?

Energy Technology Data Exchange (ETDEWEB)

Kaellstrand, B. [Uppsala Univ. (Sweden). Dept. of Meteorology

1996-12-01

When the surface conditions changes at a coastline, an internal boundary layer evolves, with a wind speed and turbulence intensity influenced by these new conditions. Aircraft measurements across the coastline, performed during near neutral conditions, are compared with a model and thirteen more simple expressions for the growth of an internal boundary layer (IBL). The majority of the expressions overestimate the IBL height, while other underestimate it. Some of the expressions give reasonable result close to the coast. The model gives good agreement, even for larger distances. The vertical potential temperature gradient turned out to be an important parameter for the growth of the IBL, even with this near neutral conditions. 21 refs, 5 figs, 1 tab

A method for aggregating external operating conditions in multi-generation system optimization models

DEFF Research Database (Denmark)

Lythcke-Jørgensen, Christoffer Ernst; Münster, Marie; Ensinas, Adriano Viana

2016-01-01

This paper presents a novel, simple method for reducing external operating condition datasets to be used in multi-generation system optimization models. The method, called the Characteristic Operating Pattern (CHOP) method, is a visually-based aggregation method that clusters reference data based...... on parameter values rather than time of occurrence, thereby preserving important information on short-term relations between the relevant operating parameters. This is opposed to commonly used methods where data are averaged over chronological periods (months or years), and extreme conditions are hidden...... in the averaged values. The CHOP method is tested in a case study where the operation of a fictive Danish combined heat and power plant is optimized over a historical 5-year period. The optimization model is solved using the full external operating condition dataset, a reduced dataset obtained using the CHOP...

Eyeblink classical conditioning and post-traumatic stress disorder - a model systems approach.

Science.gov (United States)

Schreurs, Bernard G; Burhans, Lauren B

2015-01-01

Not everyone exposed to trauma suffers flashbacks, bad dreams, numbing, fear, anxiety, sleeplessness, hyper-vigilance, hyperarousal, or an inability to cope, but those who do may suffer from post-traumatic stress disorder (PTSD). PTSD is a major physical and mental health problem for military personnel and civilians exposed to trauma. There is still debate about the incidence and prevalence of PTSD especially among the military, but for those who are diagnosed, behavioral therapy and drug treatment strategies have proven to be less than effective. A number of these treatment strategies are based on rodent fear conditioning research and are capable of treating only some of the symptoms because the extinction of fear does not deal with the various forms of hyper-vigilance and hyperarousal experienced by people with PTSD. To help address this problem, we have developed a preclinical eyeblink classical conditioning model of PTSD in which conditioning and hyperarousal can both be extinguished. We review this model and discuss findings showing that unpaired stimulus presentations can be effective in reducing levels of conditioning and hyperarousal even when unconditioned stimulus intensity is reduced to the point where it is barely capable of eliciting a response. These procedures have direct implications for the treatment of PTSD and could be implemented in a virtual reality environment.

Response of Simple, Model Systems to Extreme Conditions

Energy Technology Data Exchange (ETDEWEB)

Ewing, Rodney C. [Univ. of Michigan, Ann Arbor, MI (United States); Lang, Maik [Univ. of Michigan, Ann Arbor, MI (United States)

2015-07-30

The focus of the research was on the application of high-pressure/high-temperature techniques, together with intense energetic ion beams, to the study of the behavior of simple oxide systems (e.g., SiO₂, GeO₂, CeO₂, TiO₂, HfO₂, SnO₂, ZnO and ZrO₂) under extreme conditions. These simple stoichiometries provide unique model systems for the analysis of structural responses to pressure up to and above 1 Mbar, temperatures of up to several thousands of kelvin, and the extreme energy density generated by energetic heavy ions (tens of keV/atom). The investigations included systematic studies of radiation- and pressure-induced amorphization of high P-T polymorphs. By studying the response of simple stoichiometries that have multiple structural “outcomes”, we have established the basic knowledge required for the prediction of the response of more complex structures to extreme conditions. We especially focused on the amorphous state and characterized the different non-crystalline structure-types that result from the interplay of radiation and pressure. For such experiments, we made use of recent technological developments, such as the perforated diamond-anvil cell and in situ investigation using synchrotron x-ray sources. We have been particularly interested in using extreme pressures to alter the electronic structure of a solid prior to irradiation. We expected that the effects of modified band structure would be evident in the track structure and morphology, information which is much needed to describe theoretically the fundamental physics of track-formation. Finally, we investigated the behavior of different simple-oxide, composite nanomaterials (e.g., uncoated nanoparticles vs. core/shell systems) under coupled, extreme conditions. This provided insight into surface and boundary effects on phase stability under extreme conditions.

76 FR 81360 - Special Conditions: Gulfstream Aerospace LP (GALP) Model G280 Airplane, Operation Without Normal...

Science.gov (United States)

2011-12-28

... DEPARTMENT OF TRANSPORTATION Federal Aviation Administration 14 CFR Part 25 [Docket No. FAA-2011-1172: Special Conditions No. 25-453-SC] Special Conditions: Gulfstream Aerospace LP (GALP) Model G280... Aerospace LP (GALP) Model G280 airplane. This airplane will have a novel or unusual design feature...

An Outflow Boundary Condition Model for Noninvasive Prediction of Fractional Flow Reserve in Diseased Coronary Arteries.

Science.gov (United States)

Fayssal, Iyad A; Moukalled, Fadl; Alam, Samir; Isma'eel, Hussain

2018-04-01

This paper reports on a new boundary condition formulation to model the total coronary myocardial flow and resistance characteristics of the myocardial vascular bed for any specific patient when considered for noninvasive diagnosis of ischemia. The developed boundary condition model gives an implicit representation of the downstream truncated coronary bed. Further, it is based on incorporating patient-specific physiological parameters that can be noninvasively extracted to account for blood flow demand to the myocardium at rest and hyperemic conditions. The model is coupled to a steady three-dimensional (3D) collocated pressure-based finite volume flow solver and used to characterize the "functional significance" of a patient diseased coronary artery segment without the need for predicting the hemodynamics of the entire arterial system. Predictions generated with this boundary condition provide a deep understanding of the inherent challenges behind noninvasive image-based diagnostic techniques when applied to human diseased coronary arteries. The overall numerical method and formulated boundary condition model are validated via two computational-based procedures and benchmarked with available measured data. The newly developed boundary condition is used via a designed computational methodology to (a) confirm the need for incorporating patient-specific physiological parameters when modeling the downstream coronary resistance, (b) explain the discrepancies presented in the literature between measured and computed fractional flow reserve (FFRCT), and (c) discuss the current limitations and future challenges in shifting to noninvasive assessment of ischemia.

Displacement Models for THUNDER Actuators having General Loads and Boundary Conditions

Science.gov (United States)

Wieman, Robert; Smith, Ralph C.; Kackley, Tyson; Ounaies, Zoubeida; Bernd, Jeff; Bushnell, Dennis M. (Technical Monitor)

2001-01-01

This paper summarizes techniques for quantifying the displacements generated in THUNDER actuators in response to applied voltages for a variety of boundary conditions and exogenous loads. The PDE (partial differential equations) models for the actuators are constructed in two steps. In the first, previously developed theory quantifying thermal and electrostatic strains is employed to model the actuator shapes which result from the manufacturing process and subsequent repoling. Newtonian principles are then employed to develop PDE models which quantify displacements in the actuator due to voltage inputs to the piezoceramic patch. For this analysis, drive levels are assumed to be moderate so that linear piezoelectric relations can be employed. Finite element methods for discretizing the models are developed and the performance of the discretized models are illustrated through comparison with experimental data.

Complex dynamics and chaos control of duopoly Bertrand model in Chinese air-conditioning market

International Nuclear Information System (INIS)

Yi, Qi Guo; Zeng, Xiang Jin

2015-01-01

Highlights: •A dynamic duopoly Bertrand model with bounded rationality and quadratic cost function. •In Chinese air-conditioning market the boundary equilibrium point is locally stable. •The Lyapunov dimension of the chaos attractor is 1.9585. •The adjustment speeds may cause a market structure to behave chaotically. •The chaotic behavior can be controlled by decreasing the degree of substitutability. -- Abstract: A dynamic duopoly Bertrand model with quadratic cost function which is closer to reality and different from previous researches is discussed. The model is applied into air-conditioning market where the boundary equilibrium point is locally stable. Numerical simulations illustrate that the stability of Nash equilibrium strongly depends on the speed of adjustment of bounded rational player. The adjustment speeds and the degree of substitutability may undermine the stability of the equilibrium and cause a market structure to behave chaotically. The Lyapunov dimension of the chaos attractor is 1.9585 under some conditions. The stabilization of the chaotic behavior can be obtained by reducing the degree of substitutability. The results have an important theoretical and practical significance to Chinese air-conditioning market

Model test study of evaporation mechanism of sand under constant atmospheric condition

OpenAIRE

CUI, Yu Jun; DING, Wenqi; SONG, Weikang

2014-01-01

The evaporation mechanism of Fontainebleau sand using a large-scale model chamber is studied. First, the evaporation test on a layer of water above sand surface is performed under various atmospheric conditions, validating the performance of the chamber and the calculation method of actual evaporation rate by comparing the calculated and measured cumulative evaporations. Second,the evaporation test on sand without water layer is conducted under constant atmospheric condition. Both the evoluti...

Climate change impact on shallow groundwater conditions in Hungary: Conclusions from a regional modelling study

Science.gov (United States)

Kovács, Attila; Marton, Annamária; Tóth, György; Szöcs, Teodóra

2016-04-01

A quantitative methodology has been developed for the calculation of groundwater table based on measured and simulated climate parameters. The aim of the study was to develop a toolset which can be used for the calculation of shallow groundwater conditions for various climate scenarios. This was done with the goal of facilitating the assessment of climate impact and vulnerability of shallow groundwater resources. The simulated groundwater table distributions are representative of groundwater conditions at the regional scale. The introduced methodology is valid for modelling purposes at various scales and thus represents a versatile tool for the assessment of climate vulnerability of shallow groundwater bodies. The calculation modules include the following: 1. A toolset to calculate climate zonation from climate parameter grids, 2. Delineation of recharge zones (Hydrological Response Units, HRUs) based on geology, landuse and slope conditions, 3. Calculation of percolation (recharge) rates using 1D analytical hydrological models, 4. Simulation of the groundwater table using numerical groundwater flow models. The applied methodology provides a quantitative link between climate conditions and shallow groundwater conditions, and thus can be used for assessing climate impacts. The climate data source applied in our calculation comprised interpolated daily climate data of the Central European CARPATCLIM database. Climate zones were determined making use of the Thorntwaite climate zonation scheme. Recharge zones (HRUs) were determined based on surface geology, landuse and slope conditions. The HELP hydrological model was used for the calculation of 1D water balance for hydrological response units. The MODFLOW numerical groundwater modelling code was used for the calculation of the water table. The developed methodology was demonstrated through the simulation of regional groundwater table using spatially averaged climate data and hydrogeological properties for various time

76 FR 25229 - Special Conditions: Gulfstream Aerospace LP (GALP) Model G250 Airplane, Dynamic Test Requirements...

Science.gov (United States)

2011-05-04

... Memorandum ``Side-Facing Seats on Transport Category Airplanes'' and draft Issue Paper ``Dynamic Test...; Special Conditions No. 25-425-SC] Special Conditions: Gulfstream Aerospace LP (GALP) Model G250 Airplane... are issued for the Gulfstream Aerospace LP (GALP) model G250 airplane. This airplane will have a novel...

Computational modeling for hexcan failure under core distruptive accidental conditions

Energy Technology Data Exchange (ETDEWEB)

Sawada, T.; Ninokata, H.; Shimizu, A. [Tokyo Institute of Technology (Japan)

1995-09-01

This paper describes the development of computational modeling for hexcan wall failures under core disruptive accident conditions of fast breeder reactors. A series of out-of-pile experiments named SIMBATH has been analyzed by using the SIMMER-II code. The SIMBATH experiments were performed at KfK in Germany. The experiments used a thermite mixture to simulate fuel. The test geometry of SIMBATH ranged from single pin to 37-pin bundles. In this study, phenomena of hexcan wall failure found in a SIMBATH test were analyzed by SIMMER-II. Although the original model of SIMMER-II did not calculate any hexcan failure, several simple modifications made it possible to reproduce the hexcan wall melt-through observed in the experiment. In this paper the modifications and their significance are discussed for further modeling improvements.

Smart City Research : Contextual Conditions, Governance Models, and Public Value Assessment

NARCIS (Netherlands)

Meijer, Albert J.; Gil-Garcia, J. Ramon; Bolívar, Manuel Pedro Rodríguez

2016-01-01

There are three issues that are crucial to advancing our academic understanding of smart cities: (1) contextual conditions, (2) governance models, and (3) the assessment of public value. A brief review of recent literature and the analysis of the included papers provide support for the assumption

Wave optics modeling of real-time holographic wavefront compensation systems using OSSim

Science.gov (United States)

Carbon, Margarita A.; Guthals, Dennis M.; Logan, Jerry D.

2005-08-01

OSSim (Optical System Simulation) is a wave-optics, time-domain simulation toolbox with both optical and data processing components developed for adaptive optics (AO) systems. Diffractive wavefront control elements have recently been added that accurately model optically and electrically addressed spatial light modulators as real time holographic (RTH) devices in diffractive wavefront control systems. The developed RTH toolbox has found multiple applications for a variety of Boeing programs in solving problems of AO system analysis and design. Several complex diffractive wavefront control systems have been modeled for compensation of static and dynamic aberrations such as imperfect segmented primary mirrors and atmospheric and boundary layer turbulence. The results of OSSim simulations of RTH wavefront compensation show very good agreement with available experimental data.

Significance of settling model structures and parameter subsets in modelling WWTPs under wet-weather flow and filamentous bulking conditions

DEFF Research Database (Denmark)

Ramin, Elham; Sin, Gürkan; Mikkelsen, Peter Steen

2014-01-01

Current research focuses on predicting and mitigating the impacts of high hydraulic loadings on centralized wastewater treatment plants (WWTPs) under wet-weather conditions. The maximum permissible inflow to WWTPs depends not only on the settleability of activated sludge in secondary settling tanks...... (SSTs) but also on the hydraulic behaviour of SSTs. The present study investigates the impacts of ideal and non-ideal flow (dry and wet weather) and settling (good settling and bulking) boundary conditions on the sensitivity of WWTP model outputs to uncertainties intrinsic to the one-dimensional (1-D...... of settling parameters to the total variance of the key WWTP process outputs significantly depends on the influent flow and settling conditions. The magnitude of the impact is found to vary, depending on which type of 1-D SST model is used. Therefore, we identify and recommend potential parameter subsets...

Annual view (1999) - aeronautic relation/space relation. Aeronautic relation - manufacturing technology; Nenkan tenbo (1999) koku kankei uchu kankei. Seisan gijutsu kanren

Energy Technology Data Exchange (ETDEWEB)

NONE

2000-03-05

The aircraft manufacturing is now under the severe environment affected by the decreased manufacturing of Boeing model types. Aircraft manufacturing companies are making efforts to strengthen the civilian demand field such as the entering into the business use airplane field. It is getting more and more important to take measures for the low cost manufacturing. The measures which are proceeded with are the introduction of TPM (total productive maintenance) method, reconstruction of the production management system, etc. During the March-April period, Mitsubishi Heavy Industries, Kawasaki Heavy Industries, and Fuji Heavy Industries shipped airframe panels, wing bodies, etc. for Boeing B767-400ER model. In July, Kawasaki Heavy Industries succeeded in the first flight of the first quantity production of observation helicopter OH-1. Japan Aircraft MFG. Co. delivered the final one of Boeing MD-11 to The Boeing Co., and the cumulative total was 108. At Fuji Heavy Industries, a plant for airplane large parts surface treatment line has been completed. This is a plant to meet the integration/size-increase of airplane parts, which makes surface treatment of large parts of 20m possible. In October, the first MH-2000 helicopter of quantity production was delivered at Mitsubishi Heavy Industries. (NEDO)

A Hybrid Generalized Hidden Markov Model-Based Condition Monitoring Approach for Rolling Bearings.

Science.gov (United States)

Liu, Jie; Hu, Youmin; Wu, Bo; Wang, Yan; Xie, Fengyun

2017-05-18

The operating condition of rolling bearings affects productivity and quality in the rotating machine process. Developing an effective rolling bearing condition monitoring approach is critical to accurately identify the operating condition. In this paper, a hybrid generalized hidden Markov model-based condition monitoring approach for rolling bearings is proposed, where interval valued features are used to efficiently recognize and classify machine states in the machine process. In the proposed method, vibration signals are decomposed into multiple modes with variational mode decomposition (VMD). Parameters of the VMD, in the form of generalized intervals, provide a concise representation for aleatory and epistemic uncertainty and improve the robustness of identification. The multi-scale permutation entropy method is applied to extract state features from the decomposed signals in different operating conditions. Traditional principal component analysis is adopted to reduce feature size and computational cost. With the extracted features' information, the generalized hidden Markov model, based on generalized interval probability, is used to recognize and classify the fault types and fault severity levels. Finally, the experiment results show that the proposed method is effective at recognizing and classifying the fault types and fault severity levels of rolling bearings. This monitoring method is also efficient enough to quantify the two uncertainty components.

A Hybrid Generalized Hidden Markov Model-Based Condition Monitoring Approach for Rolling Bearings

Directory of Open Access Journals (Sweden)

Jie Liu

2017-05-01

Full Text Available The operating condition of rolling bearings affects productivity and quality in the rotating machine process. Developing an effective rolling bearing condition monitoring approach is critical to accurately identify the operating condition. In this paper, a hybrid generalized hidden Markov model-based condition monitoring approach for rolling bearings is proposed, where interval valued features are used to efficiently recognize and classify machine states in the machine process. In the proposed method, vibration signals are decomposed into multiple modes with variational mode decomposition (VMD. Parameters of the VMD, in the form of generalized intervals, provide a concise representation for aleatory and epistemic uncertainty and improve the robustness of identification. The multi-scale permutation entropy method is applied to extract state features from the decomposed signals in different operating conditions. Traditional principal component analysis is adopted to reduce feature size and computational cost. With the extracted features’ information, the generalized hidden Markov model, based on generalized interval probability, is used to recognize and classify the fault types and fault severity levels. Finally, the experiment results show that the proposed method is effective at recognizing and classifying the fault types and fault severity levels of rolling bearings. This monitoring method is also efficient enough to quantify the two uncertainty components.

Initial conditions and ENSO prediction using a coupled ocean-atmosphere model

Science.gov (United States)

Larow, T. E.; Krishnamurti, T. N.

1998-01-01

A coupled ocean-atmosphere initialization scheme using Newtonian relaxation has been developed for the Florida State University coupled ocean-atmosphere global general circulation model. The initialization scheme is used to initialize the coupled model for seasonal forecasting the boreal summers of 1987 and 1988. The atmosphere model is a modified version of the Florida State University global spectral model, resolution T-42. The ocean general circulation model consists of a slightly modified version of the Hamburg's climate group model described in Latif (1987) and Latif et al. (1993). The coupling is synchronous with information exchanged every two model hours. Using ECMWF atmospheric daily analysis and observed monthly mean SSTs, two, 1-year, time-dependent, Newtonian relaxation were performed using the coupled model prior to conducting the seasonal forecasts. The coupled initializations were conducted from 1 June 1986 to 1 June 1987 and from 1 June 1987 to 1 June 1988. Newtonian relaxation was applied to the prognostic atmospheric vorticity, divergence, temperature and dew point depression equations. In the ocean model the relaxation was applied to the surface temperature. Two, 10-member ensemble integrations were conducted to examine the impact of the coupled initialization on the seasonal forecasts. The initial conditions used for the ensembles are the ocean's final state after the initialization and the atmospheric initial conditions are ECMWF analysis. Examination of the SST root mean square error and anomaly correlations between observed and forecasted SSTs in the Niño-3 and Niño-4 regions for the 2 seasonal forecasts, show closer agreement between the initialized forecast than two, 10-member non-initialized ensemble forecasts. The main conclusion here is that a single forecast with the coupled initialization outperforms, in SST anomaly prediction, against each of the control forecasts (members of the ensemble) which do not include such an initialization

Dynamics Modeling and Simulation of Large Transport Airplanes in Upset Conditions

Science.gov (United States)

Foster, John V.; Cunningham, Kevin; Fremaux, Charles M.; Shah, Gautam H.; Stewart, Eric C.; Rivers, Robert A.; Wilborn, James E.; Gato, William

2005-01-01

As part of NASA's Aviation Safety and Security Program, research has been in progress to develop aerodynamic modeling methods for simulations that accurately predict the flight dynamics characteristics of large transport airplanes in upset conditions. The motivation for this research stems from the recognition that simulation is a vital tool for addressing loss-of-control accidents, including applications to pilot training, accident reconstruction, and advanced control system analysis. The ultimate goal of this effort is to contribute to the reduction of the fatal accident rate due to loss-of-control. Research activities have involved accident analyses, wind tunnel testing, and piloted simulation. Results have shown that significant improvements in simulation fidelity for upset conditions, compared to current training simulations, can be achieved using state-of-the-art wind tunnel testing and aerodynamic modeling methods. This paper provides a summary of research completed to date and includes discussion on key technical results, lessons learned, and future research needs.

Modeling and Forecasting the Onset and Duration of Severe Radiation Fog under Frost Conditions

NARCIS (Netherlands)

Velde, van der I.R.; Steeneveld, G.J.; Wichers Schreur, B.G.J.; Holtslag, A.A.M.

2010-01-01

A case of a severe radiation fog during frost conditions is analyzed as a benchmark for the development of a very high resolution NWP model. Results by the Weather Research and Forecasting model (WRF) and the High resolution limited area model (HIRLAM) are evaluated against detailed observations to

Wave modelling to assess the storm conditions in the Black Sea

Science.gov (United States)

Rusu, Liliana; Raileanu, Alina

2014-05-01

The work proposed herewith presents the results of a ten-year wave hindcast performed in the Black Sea and focused on the storm conditions. A wave modelling system, SWAN based, was implemented in the basin of the Black Sea. Validations have been performed both against in situ and remotely sensed data for the entire ten-year period considered (1999-2008). The wind field provided by NCEP-CFSR (United States National Centers for Environmental Prediction, Climate Forecast System Reanalysis) with a spatial resolution of 0.312ºx0.312º and a temporal resolution of 3 hours was considered for forcing the wave model. In statistical terms, the results are in general in line with those provided by similar wave prediction systems implemented in enclosed or semi-enclosed seas, the most important factors in increasing the general system reliability being the accuracy and resolution of the wind fields considered. As regards the physical processes, the calibration tests performed show that whitecapping still represents the weak link in deep water wave modelling. The most relevant storm conditions encountered in this ten-year period considered were further analysed. This analysis was performed from the point of view of the intensity, location of occurrence, duration and propagation in the geographical space of the storms. Following the results of the work, the western side of the sea is more energetic and almost each year storms with significant wave heights of about eight meters are encountered in this part of the Black Sea, while in the case of the extreme storms significant wave heights even greater than eleven meters may occur. From this perspective, it can be concluded that the present work provides valuable information about the characteristics of the storm conditions and on their dynamics in the Black Sea. Moreover, this marine environment is currently subjected to high navigation traffic and to offshore operations and the strong storms that systematically occur may produce

Modelling and analysis of radionuclide dispersion from PWR on abnormal condition in Bojanegara Serang site

International Nuclear Information System (INIS)

Sri Kuntjoro

2010-01-01

Additional of electrical power especially Nuclear Power Plant will give radiological consequence sto population and environment due to radioactive release in normal and abnormal condition. In consequence the management of nuclear power plant must supply data and strong argumentation to clarify the safety of nuclear power plant to environment. For that purpose it needs to be carried out an analysis of abnormal condition in nuclear power plant and its radiological consequences to the environment. That analysis is done using abnormal condition simulation model postulated on 1000 MWe nuclear power plant.That simulation model is used also to evaluate environmental potential as site capability in supporting the radiological consequences. Radionuclide transport modeling from reactor core to containment uses EMERALD computer code. Other computer codes are Wind rose, PC-COSYMA and Arc View are used to simulate meteorology condition, radionuclide release to population distribution of food production and consumption and distribution of radiation dose received to population around nuclear power plant. Application of that simulation is carried out to NPP candidate site in Bojanegara-Kramatwatu, Serang Banten peninsula. Using source term data, meteorology data, dispersion data and pathways modeling are resulting radionuclide dispersion model and radiation pathway acceptance at the surrounding nuclear power plant site (Bojanegara-Serang peninsula). The result shows that maximum radiation dose received is lower than dose permitted in accordance with regulatory body (BAPETEN). (author)

A note on the conditional density estimate in single functional index model

OpenAIRE

2010-01-01

Abstract In this paper, we consider estimation of the conditional density of a scalar response variable Y given a Hilbertian random variable X when the observations are linked with a single-index structure. We establish the pointwise and the uniform almost complete convergence (with the rate) of the kernel estimate of this model. As an application, we show how our result can be applied in the prediction problem via the conditional mode estimate. Finally, the estimation of the funct...

Religiousness and hazardous alcohol use: a conditional indirect effects model.

Science.gov (United States)

Jankowski, Peter J; Hardy, Sam A; Zamboanga, Byron L; Ham, Lindsay S

2013-08-01

The current study examined a conditional indirect effects model of the association between religiousness and adolescents' hazardous alcohol use. In doing so, we responded to the need to include both mediators and moderators, and the need for theoretically informed models when examining religiousness and adolescents' alcohol use. The sample consisted of 383 adolescents, aged 15-18, who completed an online questionnaire. Results of structural equation modeling supported the proposed model. Religiousness was indirectly associated with hazardous alcohol use through both positive alcohol expectancy outcomes and negative alcohol expectancy valuations. Significant moderating effects for alcohol expectancy valuations on the association between alcohol expectancies and alcohol use were also found. The effects for alcohol expectancy valuations confirm valuations as a distinct construct to that of alcohol expectancy outcomes, and offer support for the protective role of internalized religiousness on adolescents' hazardous alcohol use as a function of expectancy valuations. Copyright © 2013 The Foundation for Professionals in Services for Adolescents. Published by Elsevier Ltd. All rights reserved.

Modelling of Influence of Hypersonic Conditions on Gyroscopic Inertial Navigation Sensor Suspension

Directory of Open Access Journals (Sweden)

Korobiichuk Igor

2017-06-01

Full Text Available The upcoming hypersonic technologies pose a difficult task for air navigation systems. The article presents a designed model of elastic interaction of penetrating acoustic radiation with flat isotropic suspension elements of an inertial navigation sensor in the operational conditions of hypersonic flight. It has been shown that the acoustic transparency effect in the form of a spatial-frequency resonance becomes possible with simultaneous manifestation of the wave coincidence condition in the acoustic field and equality of the natural oscillation frequency of a finite-size plate and a forced oscillation frequency of an infinite plate. The effect can lead to additional measurement errors of the navigation system. Using the model, the worst and best case suspension oscillation frequencies can be determined, which will help during the design of a navigation system.

MATHEMATICAL MODEL FOR ESTIMATION OF MECHANICAL SYSTEM CONDITION IN DYNAMICS

Directory of Open Access Journals (Sweden)

D. N. Mironov

2011-01-01

Full Text Available The paper considers an estimation of a complicated mechanical system condition in dynamics with due account of material degradation and accumulation of micro-damages. An element of continuous medium has been simulated and described with the help of a discrete element. The paper contains description of a model for determination of mechanical system longevity in accordance with number of cycles and operational period.

Condition monitoring with wind turbine SCADA data using Neuro-Fuzzy normal behavior models

DEFF Research Database (Denmark)

Schlechtingen, Meik; Santos, Ilmar

2012-01-01

System (ANFIS) models are employed to learn the normal behavior in a training phase, where the component condition can be considered healthy. In the application phase the trained models are applied to predict the target signals, e.g. temperatures, pressures, currents, power output, etc. The behavior......This paper presents the latest research results of a project that focuses on normal behavior models for condition monitoring of wind turbines and their components, via ordinary Supervisory Control And Data Acquisition (SCADA) data. In this machine learning approach Adaptive Neuro-Fuzzy Interference...... of the prediction error is used as an indicator for normal and abnormal behavior, with respect to the learned behavior. The advantage of this approach is that the prediction error is widely decoupled from the typical fluctuations of the SCADA data caused by the different turbine operational modes. To classify...

Bio boiler - Control conditions. Part 1: Model development and analysis of operating conditions; Biokedel - Reguleringsmaessige forhold. Del 1: Modeludvikling og analyse af dynamiske driftsforhold

Energy Technology Data Exchange (ETDEWEB)

Boecher Poulsen, K.; Christensen, Torkild; Mortensen, Jan; Runge Kristoffersen, J.; Kristmundsson, E. [Tech-wise A/S (Denmark); Moekbak, T.; Mortensen, Hans Peter [Elsam A/S (Denmark)

2002-12-15

This report focuses on the model-building part of the PSO project, 'Control Conditions Bio-boiler'. In the project, which treats dynamic simulation of biomass fired power plants via the MMS software, a certain number of straw/wood chip modules have been built, together with a combustion module which, when connected to the existing MMS modules, can be used for dynamic simulation. Furthermore, a certain number of continuous and discrete components have been built which, together with the remaining MMS modules will create a complete model of the active part of the control structure under the most common operation conditions. By means of the developed straw, combustion and control modules, a model of Enstedvaerket's bio-boiler is built (without wood chip super-heater), including practically all auxiliary control mechanisms. In the report the primary problems caused by the development of the model are discussed, typically numerical problems. First of all it is discussed how a steady state condition can be reached from a nonphysical condition at the start-up of the simulation. After reaching a steady state condition at full load, the boiler load is reduced by adjusting the desired live steam flow setpoint value and the load gradient (as it would be done from the control room). While reducing to part load, one straw line is closed down, as it would be done in 'real life'. From part load, the boiler load is once again in the same way increased to full. (BA) The simulation results are then compared to measurements made on the same boiler during load reduction and load increase.

A new HYSYS model for underground gasification of hydrocarbons under hydrothermal conditions

KAUST Repository

Alshammari, Y.M.; Hellgardt, K.

2014-01-01

A new subsurface process model was developed using the ASPEN HYSYS simulation environment to analyse the process energy and gasification efficiency at steady-state equilibrium conditions. Injection and production wells were simulated using the HYSYS

Modeling and Forecasting the Onset and Duration of Severe Radiation Fog under Frost Conditions

NARCIS (Netherlands)

van der Velde, I. R.; Steeneveld, G. J.; Schreur, B. G. J. Wichers; Holtslag, A. A. M.

2010-01-01

A case of a severe radiation fog during frost conditions is analyzed as a benchmark for the development of a very high-resolution NWP model Results by the Weather Research and Forecasting model (WRF) and the High Resolution Limited Area Model (H I RLAM) are evaluated against detailed observations to

Separating expansion from contraction: generalized TOV condition, LTB models with pressure and $\\Lambda$CDM

CERN Document Server

Delliou, Morgan Le; Mimoso, José Pedro

2010-01-01

We discuss the existence of a dividing shell separating expanding and collapsing regions in spherically symmetric solutions with pressure. We obtain gauge invariant conditions relating not only the intrinsic spatial curvature of the shells to the ADM mass, but also a function of the pressure which we introduce that generalises the Tolman-Oppenheimer-Volkoff equilibrium condition, in the framework of a 3+1 spacetime splitting. We consider the particular case of a Lema\\^itre-Tolman-Bondi dust models with a cosmological constant (a $\\Lambda$-CDM model) as an example of our results.

Precipitation model in microalloyed steels both isothermal and continuous cooling conditions

International Nuclear Information System (INIS)

Medina, S. F.; Quispe, A.; Gomez, M.

2015-01-01

Niobium and vanadium precipitates (nitrides and carbides) can inhibit the static recrystallization of austenite but this does not happen for Ti, which form nitrides at high temperatures. RPTT diagrams show the interaction between recrystallization and precipitation allowing study the strain induced precipitation kinetics and precipitate coarsening. Based on Dutta and Sellars expression for the start of strain-induced precipitation in microalloyed steels, a new model has been constructed which takes into account the influence of variables such as microalloying element percentages, strain, temperature, strain rate and grain size. Recrystallization- Precipitation-Time-Temperature (RPTT) diagrams have been plotted thanks to a new experimental study carried out by means of hot torsion tests on approximately twenty microalloyed steels with different Nb, V and Ti contents. Mathematical analysis of the results recommends the modification of some parameters such as the supersaturation ratio (ks) and constant B, which is no longer a constant but a function of ks. The expressions are now more consistent and predict the Precipitation-Time-Temperature (PTT) curves with remarkable accuracy. The model for strain-induced precipitation kinetics is completed by means of Avramis equation. Finally, the model constructed in isothermal testing conditions, it has been converted to continuous cooling conditions in order to apply it in hot rolling. (Author)

Thermodynamic model of a thermal storage air conditioning system with dynamic behavior

International Nuclear Information System (INIS)

Fleming, Evan; Wen, Shaoyi; Shi, Li; Silva, Alexandre K. da

2013-01-01

Highlights: • We developed an automotive thermal storage air conditioning system model. • The thermal storage unit utilizes phase change materials. • We use semi-analytic solution to the coupled phase change and forced convection. • We model the airside heat exchange using the NTU method. • The system model can incorporate dynamic inputs, e.g. variable inlet airflow. - Abstract: A thermodynamic model was developed to predict transient behavior of a thermal storage system, using phase change materials (PCMs), for a novel electric vehicle climate conditioning application. The main objectives of the paper are to consider the system’s dynamic behavior, such as a dynamic air flow rate into the vehicle’s cabin, and to characterize the transient heat transfer process between the thermal storage unit and the vehicle’s cabin, while still maintaining accurate solution to the complex phase change heat transfer. The system studied consists of a heat transfer fluid circulating between either of the on-board hot and cold thermal storage units, which we refer to as thermal batteries, and a liquid–air heat exchanger that provides heat exchange with the incoming air to the vehicle cabin. Each thermal battery is a shell-and-tube configuration where a heat transfer fluid flows through parallel tubes, which are surrounded by PCM within a larger shell. The system model incorporates computationally inexpensive semi-analytic solution to the conjugated laminar forced convection and phase change problem within the battery and accounts for airside heat exchange using the Number of Transfer Units (NTUs) method for the liquid–air heat exchanger. Using this approach, we are able to obtain an accurate solution to the complex heat transfer problem within the battery while also incorporating the impact of the airside heat transfer on the overall system performance. The implemented model was benchmarked against a numerical study for a melting process and against full system

Conditions for Model Matching of Switched Asynchronous Sequential Machines with Output Feedback

OpenAIRE

Jung–Min Yang

2016-01-01

Solvability of the model matching problem for input/output switched asynchronous sequential machines is discussed in this paper. The control objective is to determine the existence condition and design algorithm for a corrective controller that can match the stable-state behavior of the closed-loop system to that of a reference model. Switching operations and correction procedures are incorporated using output feedback so that the controlled switched machine can show the ...

New model for colour kinetics of plum under infrared vacuum condition and microwave drying.

Science.gov (United States)

Chayjan, Reza Amiri; Alaei, Behnam

2016-01-01

Quality of dried foods is affected by the drying method and physiochemical changes in tissue. The drying method affects properties such as colour. The colour of processed food is one of the most important quality indices and plays a determinant role in consumer acceptability of food materials and the processing method. The colour of food materials can be used as an indirect factor to determine changes in quality, since it is simpler and faster than chemical methods. The study focused on the kinetics of colour changes of plum slices, under infrared vacuum and microwave conditions. Drying the samples was implemented at the absolute pressures of 20 and 60 kPa, drying temperatures of 50 and 60°C and microwave power of 90, 270, 450 and 630 W. Colour changes were quantified by the tri-stimulus L* (whiteness/darkness), a* (redness/greenness) and b* (yellowness/blueness) model, which is an international standard for color measurement developed by the Commission Internationale d'Eclairage (CIE). These values were also used to calculate total colour change (∆E), chroma, hue angle, and browning index (BI). A new model was used for mathematical modelling of colour change kinetics. The drying process changed the colour parameters of L*, a*, and b*, causing a colour shift toward the darker region. The values of L* and hue angle decreased, whereas the values of a*, b*, ∆E, chroma and browning index increased during exposure to infrared vacuum conditions and microwave drying. Comparing the results obtained using the new model with two conventional models of zero-order and first-order kinetics indicated that the new model presented more compatibility with the data of colour kinetics for all colour parameters and drying conditions. All kinetic changes in colour parameters can be explained by the new model presented in this study. The hybrid drying system included infrared vacuum conditions and microwave power for initial slow drying of plum slices and provided the desired

Nonlinear modeling of magnetorheological energy absorbers under impact conditions

Science.gov (United States)

Mao, Min; Hu, Wei; Choi, Young-Tai; Wereley, Norman M.; Browne, Alan L.; Ulicny, John; Johnson, Nancy

2013-11-01

Magnetorheological energy absorbers (MREAs) provide adaptive vibration and shock mitigation capabilities to accommodate varying payloads, vibration spectra, and shock pulses, as well as other environmental factors. A key performance metric is the dynamic range, which is defined as the ratio of the force at maximum field to the force in the absence of field. The off-state force is typically assumed to increase linearly with speed, but at the higher shaft speeds occurring in impact events, the off-state damping exhibits nonlinear velocity squared damping effects. To improve understanding of MREA behavior under high-speed impact conditions, this study focuses on nonlinear MREA models that can more accurately predict MREA dynamic behavior for nominal impact speeds of up to 6 m s-1. Three models were examined in this study. First, a nonlinear Bingham-plastic (BP) model incorporating Darcy friction and fluid inertia (Unsteady-BP) was formulated where the force is proportional to the velocity. Second, a Bingham-plastic model incorporating minor loss factors and fluid inertia (Unsteady-BPM) to better account for high-speed behavior was formulated. Third, a hydromechanical (HM) analysis was developed to account for fluid compressibility and inertia as well as minor loss factors. These models were validated using drop test data obtained using the drop tower facility at GM R&D Center for nominal drop speeds of up to 6 m s-1.

Co-occurrence of medical conditions: Exposing patterns through probabilistic topic modeling of snomed codes.

Science.gov (United States)

Bhattacharya, Moumita; Jurkovitz, Claudine; Shatkay, Hagit

2018-04-12

Patients associated with multiple co-occurring health conditions often face aggravated complications and less favorable outcomes. Co-occurring conditions are especially prevalent among individuals suffering from kidney disease, an increasingly widespread condition affecting 13% of the general population in the US. This study aims to identify and characterize patterns of co-occurring medical conditions in patients employing a probabilistic framework. Specifically, we apply topic modeling in a non-traditional way to find associations across SNOMED-CT codes assigned and recorded in the EHRs of >13,000 patients diagnosed with kidney disease. Unlike most prior work on topic modeling, we apply the method to codes rather than to natural language. Moreover, we quantitatively evaluate the topics, assessing their tightness and distinctiveness, and also assess the medical validity of our results. Our experiments show that each topic is succinctly characterized by a few highly probable and unique disease codes, indicating that the topics are tight. Furthermore, inter-topic distance between each pair of topics is typically high, illustrating distinctiveness. Last, most coded conditions grouped together within a topic, are indeed reported to co-occur in the medical literature. Notably, our results uncover a few indirect associations among conditions that have hitherto not been reported as correlated in the medical literature. Copyright © 2018. Published by Elsevier Inc.

Monitoring growth condition of spring maize in Northeast China using a process-based model

Science.gov (United States)

Wang, Peijuan; Zhou, Yuyu; Huo, Zhiguo; Han, Lijuan; Qiu, Jianxiu; Tan, Yanjng; Liu, Dan

2018-04-01

Early and accurate assessment of the growth condition of spring maize, a major crop in China, is important for the national food security. This study used a process-based Remote-Sensing-Photosynthesis-Yield Estimation for Crops (RS-P-YEC) model, driven by satellite-derived leaf area index and ground-based meteorological observations, to simulate net primary productivity (NPP) of spring maize in Northeast China from the first ten-day (FTD) of May to the second ten-day (STD) of August during 2001-2014. The growth condition of spring maize in 2014 in Northeast China was monitored and evaluated spatially and temporally by comparison with 5- and 13-year averages, as well as 2009 and 2013. Results showed that NPP simulated by the RS-P-YEC model, with consideration of multi-scattered radiation inside the crop canopy, could reveal the growth condition of spring maize more reasonably than the Boreal Ecosystem Productivity Simulator. Moreover, NPP outperformed other commonly used vegetation indices (e.g., Normalized Difference Vegetation Index (NDVI) and Enhanced Vegetation Index (EVI)) for monitoring and evaluating the growth condition of spring maize. Compared with the 5- and 13-year averages, the growth condition of spring maize in 2014 was worse before the STD of June and after the FTD of August, and it was better from the third ten-day (TTD) of June to the TTD of July across Northeast China. Spatially, regions with slightly worse and worse growth conditions in the STD of August 2014 were concentrated mainly in central Northeast China, and they accounted for about half of the production area of spring maize in Northeast China. This study confirms that NPP is a good indicator for monitoring and evaluating growth condition because of its capacity to reflect the physiological characteristics of crops. Meanwhile, the RS-P-YEC model, driven by remote sensing and ground-based meteorological data, is effective for monitoring crop growth condition over large areas in a near real

Simplified model-based optimal control of VAV air-conditioning system

Energy Technology Data Exchange (ETDEWEB)

Nassif, N.; Kajl, S.; Sabourin, R. [Ecole de Technologie Superieure, Montreal, PQ (Canada). Dept. of Construction Engineering

2005-07-01

The improvement of Variable Air Volume (VAV) system performance is one of several attempts being made to minimize the high energy use associated with the operation of heating, ventilation and air conditioning (HVAC) systems. A Simplified Optimization Process (SOP) comprised of controller set point strategies and a simplified VAV model was presented in this paper. The aim of the SOP was to determine supply set points. The advantage of the SOP over previous methods was that it did not require a detailed VAV model and optimization program. In addition, the monitored data for representative local-loop control can be checked on-line, after which controller set points can be updated in order to ensure proper operation by opting for real situations with minimum energy use. The SOP was validated using existing monitoring data and a model of an existing VAV system. Energy use simulations were compared to that of the existing VAV system. At each simulation step, 3 controller set point values were proposed and studied using the VAV model in order to select a value for each point which corresponded to the best performance of the VAV system. Simplified VAV component models were presented. Strategies for controller set points were described, including zone air temperature, duct static pressure set points; chilled water supply set points and supply air temperature set points. Simplified optimization process calculations were presented. Results indicated that the SOP provided significant energy savings when applied to specific AHU systems. In a comparison with a Detailed Optimization Process (DOP), the SOP was capable of determining set points close to those obtained by the DOP. However, it was noted that the controller set points determined by the SOP need a certain amount of time to reach optimal values when outdoor conditions or thermal loads are significantly changed. It was suggested that this disadvantage could be overcome by the use of a dynamic incremental value, which

Asymmetries in conditional mean and variance: Modelling stock returns by asMA-asQGARCH

NARCIS (Netherlands)

Brännäs, K.; de Gooijer, J.G.

2000-01-01

The asymmetric moving average model (asMA) is extended to allow for asymmetric quadratic conditional heteroskedasticity (asQGARCH). The asymmetric parametrization of the condi- tional variance encompasses the quadratic GARCH model of Sentana (1995). We introduce a framework for testing asymmetries

Simulation of potato yield in temperate condition by the AquaCrop model

DEFF Research Database (Denmark)

Razzaghi, Fatemeh; Zhenjiang, Zhou; Andersen, Mathias Neumann

2017-01-01

Potato production ranks fourth in the world after rice, wheat, and maize and it is highly sensitive to water stress. It is thus very important to implement irrigation management strategies to minimize the effects of water stress under different climate conditions. The use of modelling tools...... to calculate the soil water balance on a daily basis has become widespread in the last decades. Therefore, this study was performed to simulate potato yield, dry matter and soil water content under different water stress condition using the AquaCrop model. Three levels of irrigation comprising full irrigated...... (If), deficit irrigated (Id) and not irrigated (I0) were investigated in three-years potato field experiment (2013–15) with four replicates in randomized complete block design. Tuber and total dry matter yield, canopy cover, dry matter production during the crop growth season, and soil water content...

Legendre condition and the stabilization problem for classical soliton solutions in generalized Skyrme models

International Nuclear Information System (INIS)

Kiknadze, N.A.; Khelashvili, A.A.

1990-01-01

The problem on stability of classical soliton solutions is studied from the unique point of view: the Legendre condition - necessary condition of existence of weak local minimum for energy functional (term soliton is used here in the wide sense) is used. Limits to parameters of the model Lagrangians are obtained; it is shown that there is no soliton stabilization in some of them despite the phenomenological achievements. The Jacoby sufficient condition is discussed

Modelling of domestic refrigerators' energy consumption under real life conditions in Europe

Energy Technology Data Exchange (ETDEWEB)

Geppert, Jasmin

2011-05-23

In recent decades, energy and resource savings have become increasingly important, not only in the industrial, but also the residential sector. As one of the largest energy users in private homes, domestic refrigerators and freezers were among the first appliances to be targeted for energy efficiency improvements. With the aim of encouraging manufacturers to develop and produce more efficient appliances, the European Energy Label was introduced in the mid-nineties. However, the energy use of refrigerators does not only depend on technical components and features. Especially the using conditions in private homes are of a decisive influence. Thus, the present study has been conducted to test the sensitivity of refrigerators' energy consumption to various usage conditions within realistic ranges, which have been determined by means of two empirical studies. Key information gathered from the experiments were used as a base for the development and validation of a simplified model that allows predicting the energy consumption of refrigerators in use. The practical experiments were performed under controlled laboratory conditions with four different refrigerators with an A{sup +} or A{sup ++} energy efficiency rating (two statically cooled built-in fridge-freezers, one dynamically cooled refrigerator and one statically cooled refrigerator). The investigations revealed that the ambient temperature has the greatest impact on a refrigerator's energy consumption, followed by thermostat setting and heat load by insertion of warm items. The refrigerators' load under static conditions as well as the number of door openings have almost no impact on energy consumption. The modelling methodology follows a first-principle approach adjusted by experimental data. When compared to experimental results, model predictions show a reasonable agreement for the whole range of investigated conditions. (orig.)

Analysis of metal forming processes by using physical modeling and new plastic similarity condition

International Nuclear Information System (INIS)

Gronostajski, Z.; Hawryluk, M.

2007-01-01

In recent years many advances have been made in numerical methods, for linear and non-linear problems. However the success of them depends very much on the correctness of the problem formulation and the availability of the input data. Validity of the theoretical results can be verified by an experiment using the real or soft materials. An essential reduction of time and costs of the experiment can be obtained by using soft materials, which behaves in a way analogous to that of real metal during deformation. The advantages of using of the soft materials are closely connected with flow stress 500 to 1000 times lower than real materials. The accuracy of physical modeling depend on the similarity conditions between physical model and real process. The most important similarity conditions are materials similarity in the range of plastic and elastic deformation, geometrical, frictional and thermal similarities. New original plastic similarity condition for physical modeling of metal forming processes is proposed in the paper. It bases on the mathematical description of similarity of the flow stress curves of soft materials and real ones

Modelling of Edge Insulation Depending on Boundary Conditions for the Ground Level

Science.gov (United States)

Stolarska, Agata; Strzałkowski, Jarosław

2017-10-01

The article presents results of CFD software aided simulations of a thermal bridge, existing at the wall-slab on ground connection. Calculations were made for different variants of the edge insulation location. Schemes without any edge insulation, with some vertical insulation, horizontal, diagonal, and diagonal combined with insulation used as formwork under the slab on ground were analysed. Each variant was differentiated with boundary conditions for the ground. Vertical borders of the model in the ground, as well as the lower border were described in the first solution as adiabatic, while in the second case, a variable temperature value, depending on the ground depth, was set. For comparison, additional calculations were conducted for non-stationary conditions, in which the initial temperature of the ground was set to the average annual temperature of air. The calculations were based on the location of Szczecin, for which the outside air temperature was set to -16.0°C. Results obtained from the simulation were then used to determine the thermal bridge parameters, in particular, thermal coupling coefficient and linear thermal transmittance. The effect of the set of boundary conditions is clearly seen. In general, for all the five variants, lower values of heat fluxes and linear thermal transmittances were obtained, when variable temperature in the ground was assumed. From the point of view of energy balance, it is more favourable to use the values of ψg obtained when the ground temperature is taken into account. The data breakdown shows that application of the actual temperature distribution in the ground to a model has a strong effect on distribution of the 0.0°C isotherm. The adiabatic model indicates that the ground under the slab freezes, while the model, which takes into account the temperature of the ground, shows that the ground under the floor has positive temperatures and the 0.0°C isotherm reaches only the edge of the outer wall. Moreover, the

Modeling Daily Rainfall Conditional on Atmospheric Predictors: An application to Western Greece

Science.gov (United States)

Langousis, Andreas; Kaleris, Vassilios

2013-04-01

Due to its intermittent and highly variable character, daily precipitation is the least well reproduced hydrologic variable by both General Circulation Models (GCMs) and Limited Area Models (LAMs). To that extent, several statistical procedures (usually referred to as downscaling schemes) have been suggested to generate synthetic rainfall time series conditional on predictor variables that are descriptive of the atmospheric circulation at the mesoscale. In addition to be more accurately simulated by GCMs and LAMs, large-scale atmospheric predictors are important indicators of the local weather. Currently used downscaling methods simulate rainfall series using either stable statistical relationships (usually referred to as transfer functions) between certain characteristics of the rainfall process and mesoscale atmospheric predictor variables, or simple stochastic schemes (e.g. properly transformed autoregressive models) with parameters that depend on the large-scale atmospheric conditions. The latter are determined by classifying large-scale circulation patterns into broad categories of weather states, using empirical or theoretically based classification schemes, and modeled by resampling from those categories; a process usually referred to as weather generation. In this work we propose a statistical framework to generate synthetic rainfall timeseries at a daily level, conditional on large scale atmospheric predictors. The latter include the mean sea level pressure (MSLP), the magnitude and direction of upper level geostrophic winds, and the 500 hPa geopotential height, relative vorticity and divergence. The suggested framework operates in continuous time, avoiding the use of transfer functions, and weather classification schemes. The suggested downscaling approach is validated using atmospheric data from the ERA-Interim archive (see http://www.ecmwf.int/research/era/do/get/index), and daily rainfall data from Western Greece, for the 14-year period from 01 October

Variable Width Riparian Model Enhances Landscape and Watershed Condition

Science.gov (United States)

Abood, S. A.; Spencer, L.

2017-12-01

Riparian areas are ecotones that represent about 1% of USFS administered landscape and contribute to numerous valuable ecosystem functions such as wildlife habitat, stream water quality and flows, bank stability and protection against erosion, and values related to diversity, aesthetics and recreation. Riparian zones capture the transitional area between terrestrial and aquatic ecosystems with specific vegetation and soil characteristics which provide critical values/functions and are very responsive to changes in land management activities and uses. Two staff areas at the US Forest Service have coordinated on a two phase project to support the National Forests in their planning revision efforts and to address rangeland riparian business needs at the Forest Plan and Allotment Management Plan levels. The first part of the project will include a national fine scale (USGS HUC-12 digits watersheds) inventory of riparian areas on National Forest Service lands in western United States with riparian land cover, utilizing GIS capabilities and open source geospatial data. The second part of the project will include the application of riparian land cover change and assessment based on selected indicators to assess and monitor riparian areas on annual/5-year cycle basis.This approach recognizes the dynamic and transitional nature of riparian areas by accounting for hydrologic, geomorphic and vegetation data as inputs into the delineation process. The results suggest that incorporating functional variable width riparian mapping within watershed management planning can improve riparian protection and restoration. The application of Riparian Buffer Delineation Model (RBDM) approach can provide the agency Watershed Condition Framework (WCF) with observed riparian area condition on an annual basis and on multiple scales. The use of this model to map moderate to low gradient systems of sufficient width in conjunction with an understanding of the influence of distinctive landscape

Implementation and verification of a coupled fire model as a thermal boundary condition within P3/THERMAL

International Nuclear Information System (INIS)

Hensinger, D.M.; Gritzo, L.A.; Koski, J.A.

1996-01-01

A user-defined boundary condition subroutine has been implemented within P3/THERMAL to represent the heat flux between a noncombusting object and an engulfing fire. The heat flux calculations includes a simple 2D fire model in which energy and radiative heat transport equations are solved to produce estimates of the heat fluxes at the fire-object interface. These estimates reflect radiative coupling between a cold object and the flow of hot combustion gases which has been observed in fire experiments. The model uses a database of experimental pool fire measurements for far field boundary conditions and volumetric heat release rates. Taking into account the coupling between a structure and the fire is an improvement over the σT 4 approximation frequently used as a boundary condition for engineered system response and is the preliminary step in the development of a fire model with a predictive capability. This paper describes the implementation of the fire model as a P3/THERMAL boundary condition and presents the results of a verification calculation carried out using the model

On conditions and parameters important to model sensitivity for unsaturated flow through layered, fractured tuff

International Nuclear Information System (INIS)

Prindle, R.W.; Hopkins, P.L.

1990-10-01

The Hydrologic Code Intercomparison Project (HYDROCOIN) was formed to evaluate hydrogeologic models and computer codes and their use in performance assessment for high-level radioactive-waste repositories. This report describes the results of a study for HYDROCOIN of model sensitivity for isothermal, unsaturated flow through layered, fractured tuffs. We investigated both the types of flow behavior that dominate the performance measures and the conditions and model parameters that control flow behavior. We also examined the effect of different conceptual models and modeling approaches on our understanding of system behavior. The analyses included single- and multiple-parameter variations about base cases in one-dimensional steady and transient flow and in two-dimensional steady flow. The flow behavior is complex even for the highly simplified and constrained system modeled here. The response of the performance measures is both nonlinear and nonmonotonic. System behavior is dominated by abrupt transitions from matrix to fracture flow and by lateral diversion of flow. The observed behaviors are strongly influenced by the imposed boundary conditions and model constraints. Applied flux plays a critical role in determining the flow type but interacts strongly with the composite-conductivity curves of individual hydrologic units and with the stratigraphy. One-dimensional modeling yields conservative estimates of distributions of groundwater travel time only under very limited conditions. This study demonstrates that it is wrong to equate the shortest possible water-travel path with the fastest path from the repository to the water table. 20 refs., 234 figs., 10 tabs

The modeling of fuel rod behaviour under RIA conditions in the code DYN3D

International Nuclear Information System (INIS)

Rohde, U.

1998-01-01

A description of the fuel rod behaviour and heat transfer model used in the code DYN3D for nuclear reactor core dynamic simulations is given. Besides the solution of heat conduction equations in fuel and cladding, the model comprises detailed description of heat transfer in the gas gap by conduction, radiation and fuel-cladding contact. The gas gap behaviour is modeled in a mechanistic way taking into account transient changes of the gas gap parameters based on given conditions for the initial state. Thermal, elastic and plastic deformations of fuel and cladding are taken into account within 1D approximation. Numerical studies concerning the fuel rod behaviour under RIA conditions in power reactors are reported. Fuel rod behaviour at high pressures and flow rates in power reactors is different from the behaviour under atmospheric pressure and stagnant flow conditions in the experiments. The mechanisms of fuel rod failure for fresh and burned fuel reported from the literature can be qualitatively reproduced by the DYN3D model. (author)

Recharge and Lateral Groundwater Flow Boundary Conditions for the Saturated Zone Site-Scale Flow and Transport Model

Energy Technology Data Exchange (ETDEWEB)

B. Arnold; T. Corbet

2001-12-18

The purpose of the flow boundary conditions analysis is to provide specified-flux boundary conditions for the saturated zone (SZ) site-scale flow and transport model. This analysis is designed to use existing modeling and analysis results as the basis for estimated groundwater flow rates into the SZ site-scale model domain, both as recharge at the upper (water table) boundary and as underflow at the lateral boundaries. The objective is to provide consistency at the boundaries between the SZ site-scale flow model and other groundwater flow models. The scope of this analysis includes extraction of the volumetric groundwater flow rates simulated by the SZ regional-scale flow model to occur at the lateral boundaries of the SZ site-scale flow model and the internal qualification of the regional-scale model for use in this analysis model report (AMR). In addition, the scope includes compilation of information on the recharge boundary condition taken from three sources: (1) distributed recharge as taken from the SZ regional-scale flow model, (2) recharge below the area of the unsaturated zone (UZ) site-scale flow model, and (3) focused recharge along the Fortymile Wash channel.