Technology development of protein rich concentrates for nutrition in extreme conditions using soybean and meat by-products.

Science.gov (United States)

Kalenik, Tatiana K; Costa, Rui; Motkina, Elena V; Kosenko, Tamara A; Skripko, Olga V; Kadnikova, Irina A

2017-01-01

There is a need to develop new foods for participants of expeditions in extreme conditions, which must be self-sufficient. These foods should be light to carry, with a long shelf life, tasty and with  high nutrient density. Currently, protein sources are limited mainly to dried and canned meat. In this work, a protein-rich dried concentrate suitable for extreme expeditions was developed using soya, tomato, milk whey and meat by-products. Protein concentrates were developed using minced beef liver and heart, dehydrated and mixed with a soya protein-lycopene coagulate (SPLC) obtained from a solution prepared with germi- nated soybeans and mixed with tomato paste in milk whey, and finally dried. The technological parameters of pressing SPLC and of drying the protein concentrate were optimized using response surface methodology. The optimized technological parameters to prepare the protein concentrates were obtained, with 70:30 being the ideal ratio of minced meat to SPLC. The developed protein concentrates are characterized by a high calorific value of 376 kcal/100 g of dry product, with a water content of 98 g·kg-1, and 641-644 g·kg-1 of proteins. The essential amino acid indices are 100, with minimum essential amino acid content constitut- ing 100-128% of the FAO standard, depending on the raw meat used. These concentrates are also rich in micronutrients such as β-carotene and vitamin C. Analysis of the nutrient content showed that these non-perishable concentrates present a high nutritional value and complement other widely available vegetable concentrates to prepare a two-course meal. The soups and porridges prepared with these concentrates can be classified as functional foods, and comply with army requirements applicable to food products for extreme conditions.

Dual curvature acoustically damped concentrating collector. Final technical report

Energy Technology Data Exchange (ETDEWEB)

Smith, G.A.; Rausch, R.A.

1980-05-01

A development program was conducted to investigate the design and performance parameters of a novel, dual curvature, concentrating solar collector. The reflector of the solar collector is achieved with a stretched-film reflective surface that approximates a hyperbolic paraboloid and is capable of line-focusing at concentration ratios ranging from 10 to 20X. A prototype collector was designed based on analytical and experimental component trade-off activities as well as economic analyses of solar thermal heating and cooling systems incorporating this type of collector. A prototype collector incorporating six 0.66 x 1.22 m (2 x 4 ft) was fabricated and subjected to a limited thermal efficiency test program. A peak efficiency of 36% at 121/sup 0/C (250/sup 0/F) was achieved based upon the gross aperture area. Commercialization activities were conducted, including estimated production costs of $134.44/m/sup 2/ ($12.49/ft/sup 2/) for the collector assembly (including a local suntracker and controls) and $24.33/m/sup 2/ ($2.26/ft/sup 2/) for the reflector subassembly.

Development of free surface flow between concentric cylinders with vertical axes

International Nuclear Information System (INIS)

Watanabe, T; Toya, Y; Nakamura, I

2005-01-01

Numerical and experimental studies are conducted on flows developing between two concentric cylinders with vertical axes. The inner cylinder rotates and the outer and the lower end wall are fixed. The upper boundary is a free surface. The flow is at rest in an initial state, and the inner cylinder impulsively begins to rotate or its rotation speed linearly increases to a prescribed value. The acceleration rate of the inner cylinder changes the formation processes of flows and/or the final flow modes. Time-dependent flows appear at higher Reynolds numbers, and the numerical and experimental results of the power spectra show some agreements. It is suggested that critical Reynolds numbers appear, at which the fluctuations in the displacement of the free surface and the kinetic energy of a velocity component steeply increase

Performance, rumen development, and carcass traits of male calves fed starter concentrate with crude glycerin

Directory of Open Access Journals (Sweden)

Raylon Pereira Maciel

2016-06-01

Full Text Available ABSTRACT The objective of this study was to assess the effects of including crude glycerin in the diet on intake, performance, rumen development, and carcass traits of dairy crossbred veal calves fed starter concentrate containing 0, 80, 160, and 240 g kg−1 crude glycerin. Twenty-eight calves with an average weight of 38.03±6.7 kg and five days of age were distributed in a completely randomized design with four treatments with seven replications. Calves were individually housed in covered stalls equipped with feeders and drinkers for 56 days. The calf response to inclusion of crude glycerin in the concentrate changed over the weeks and the inclusion level of 240 g kg−1 resulted in greater dry matter intake and average daily gain. There was no effect on the final weight and total weight gain of the animals, with mean values of 73.60 and 35.16 kg, respectively. The weight of the rumen-reticulum adjusted for body weight, empty body weight, and total stomach weight increased linearly with the inclusion of crude glycerin. Blood total protein, globulin, urea, cholesterol, gamma glutamyl transferase, aspartate aminotransferase, and alkaline phosphatase concentrations did not differ among treatments. Carcass traits and meat color were not affected. Crude glycerin can be added to dairy calf starter concentrate up to 240 g kg−1 dry matter because it benefits concentrate intake, performance, and rumen development without affecting animal health.

Refining of fossil resin flotation concentrate from western coal. Final report

Energy Technology Data Exchange (ETDEWEB)

Jensen, G.F.; Miller, J.D.

1995-02-16

During the past several years, significant research efforts have been made to develop process technology for the selective flotation of fossil resin from western coals. As a result of these efforts, several new flotation technologies have been developed. Operation of a proof-of-concept continuous flotation circuit showed the selective flotation process to be sufficiently profitable to justify the development of a fossil resin industry. However, little attention has been given to the refining of the fossil resin flotation concentrate although solvent refining is a critical step for the fossil resin to become a marketable product. In view of this situation, DOE funded this two-year project to evaluate the following aspects of the fossil resin refining technology: 1) Characterization of the fossil resin flotation concentrate and its refined products; 2) Kinetics of fossil resin extraction; 3) Effects of operating variables on solvent extraction; 4) Extraction solvents; 5) Proof-of-concept continuous refining tests; and 6) Technical and economic analysis. The results from this research effort have led to the following conclusions: Hexane- or heptane-refined fossil resin has a light-yellow color, a melting point of 140 - 142{degrees}C, a density of 1.034 gram/cm, and good solubility in nonpolar solvents. Among the four solvents evaluated (hexane, heptane, toluene and ethyl acetate), hexane is the most appropriate solvent based on overall technical and economic considerations. Batch extraction tests and kinetic studies suggest that the main interaction between the resin and the solvent is expected to be the forces associated with solvation phenomena. Temperature has the most significant effect on extraction rate. With hexane as the solvent, a recovery of 90% cam be achieved at 50{degrees}C and 10% solids concentration with moderate agitation for 1 hour.

Development of high field superconductors for fusion energy applications. Final report

International Nuclear Information System (INIS)

1985-01-01

The purpose of this project was to develop a conductor design and a manufacturing procedure for a composite multifilamentary Nb 3 Sn conductor suitable for winding a magnet for use in a fusion energy power plant. Effort was concentrated on the design of a conductor with tubular niobium filaments in a copper matrix. Bronze in the bores of the filaments would react with the niobium to form Nb 3 Sn on the inside diameter of the niobium tubular filaments during a heat treatment at final size. Four filament geometries were evaluated. The addition of titanium to the bronze was found to increase the current density. The use of a hydrogen atmosphre did not appear to cause any increase in current density. Primary billets were assembled and extruded with five tubular filament designs and for comparison, five rod type filament designs. Billet designs are described

Bank concentration, country income and financial development in ...

African Journals Online (AJOL)

kirstam

between bank concentration and financial development in the SADC region. ... 5The study findings suggest that bank assets in SADC are concentrated in ... a country's cities/administrative regions, or across countries within a regional ... sector emphasises the importance of local embeddedness, networks, ...... The Case of.

Portable linear accelerator development. Final report

International Nuclear Information System (INIS)

Schonberg, R.G.

1983-01-01

The final report on Project RP 822-6 describes the MINAC 3 development from the recognition of need for a lightweight, portable high-energy device to the successful completion and field use of the MINAC. MINAC, which represents a substantial improvement in field radiographic capability and in technology, rapidly transitioned from proof-of-principle (1978 to 1980) to field-proven product (1980 to 1981). As a result, the decision has been made to develop this report as a users guide as well as a historic record of design, development, and testing program. The first section of this report has the following principal objectives: to describe the existing MINAC equipment capabilities and achievable modifications; to provide applications information for prospective users; and to provide technical information on high-energy radiography useful for familiarization and planning. The users guide section is followed by sections which describe the design basis, development, and application history of MINAC through the course of EPRI RP822 research projects 1 to 5, inclusively

Simulation and development of a multi-leg homogeniser concentrating assembly for concentrated photovoltaic (CPV) system with electrical rating analysis

International Nuclear Information System (INIS)

Burhan, Muhammad; Chua, Kian Jon Ernest; Ng, Kim Choon

2016-01-01

Highlights: • Novel multi-leg homogeniser concentrating assembly is developed for CPV system. • Single set of concentrator, concentrates sunlight on 4 MJCs with 1° acceptance angle. • The system performance is analyzed through experiment and ray tracing simulation. • Mini two axis solar tracker, with high tracking accuracy, is developed and tested. • Electrical rating analysis accurately estimates CPV system performance in any region. - Abstract: Concentrated photovoltaic (CPV) system utilizing multi-junction solar cells, is the main focus for current research, offering highest efficiency among all photovoltaic systems. The main aspect of CPV system is the design and performance of concentrating assembly, as it determines the performance of whole CPV system. However, the conventional design of CPV concentrating assembly dedicates one concentrator for each solar cell, in which single concentrator is capable to concentrate solar radiation onto single solar cell. This paper proposes a novel concentrating assembly for CPV system, which is designed to concentrate solar radiation onto four multi-junction solar cells with a single set of concentrators. The proposed design not only can reduce the number of concentrators and assembly efforts for CPV systems, but also achieved an acceptance angle of 1°. In this paper, the proposed multi-leg homogeniser CPV concentrating assembly is designed, developed, experimentally tested and verified through ray tracing simulation. The paper also discuss the development of mini, precise and accurate but cost effective two axis solar tracker for CPV system, which can be installed at any location even at rooftop of residential buildings, unlike conventional large scale CPV systems. Moreover, through the electrical rating analysis of the developed CPV system, its performance can be accurately estimated in any region.

Final storage of radioactive waste - how soon will we be able to catch up again with international developments?

International Nuclear Information System (INIS)

Kuehn, K.

2006-01-01

In Germany, the final storage of radioactive waste from the beginning has been a topic very much influenced by the political debate, especially by party politics. The development initiated after the 1998 change in government has greatly contributed to Germany clearly losing contact with cutting edge international developments in final storage. Here are some proposals for improving the present situation: - The political demand for a single-repository concept should be given up. - Preparatory work on the Konrad repository should be started. - Underground exploration of the Gorleben salt dome should be resumed without any strings attached. - A TSPA should be conducted for the Gorleben project. - After completion of the TSPA, an international peer review should be carried out of the Gorleben project. - An underground laboratory in salt should be established in Germany. - Repository activities should be transferred to a company organized and operating along industrial lines. - Competence for licensing radioactive waste repositories should be concentrated on a national level. (orig.)

Carbon dioxide concentrations are very high in developing oilseeds.

Science.gov (United States)

Goffman, Fernando D; Ruckle, Mike; Ohlrogge, John; Shachar-Hill, Yair

2004-09-01

A new method has been developed to rapidly determine the total inorganic carbon concentration (gaseous [CO2] + aqueous [CO(2)] + [HCO3-] + [CO3(2)-]) in developing seeds. Seeds are rapidly dissected and homogenized in 1 N HCl in gas-tight vials. The headspace gas is then analyzed by infrared gas analysis. Developing rapeseed (Brassica napus L.) and soybean [Glycine max (L.) Merr.] seeds were analyzed and found to have up to 40 and 12 mM total inorganic carbon, respectively. These concentrations are ca. 600-2000-fold higher than in ambient air or values reported for leaves. Carbon dioxide concentrations in rapeseed peaked during the stage of maximum oil synthesis and declined as seeds matured. The consequences for seed metabolism, physiology and carbon economy are discussed.

Silicon concentrator cells in a two-stage photovoltaic system with a concentration factor of 300x

Energy Technology Data Exchange (ETDEWEB)

Mohr, A.

2005-06-15

In this work a rear contacted silicon concentrator cell was developed for an application in a two stage concentrator photovoltaic system. This system was developed at Fraunhofer ISE some years ago. The innovation of this one-axis tracked system is that it enables a high geometrical concentration of 300x in combination with a high optical efficiency (around 78%) and a large acceptance angle of {+-}23.5 all year through. For this, the system uses a parabolic mirror (40.4x) and a three dimensional second stage consisting of compound parabolic concentrators (CPCs, 7.7x). For the concentrator concept and particularly for an easy cell integration, the rear line contacted concentrator (RLCC) cells with a maximum efficiency of 25% were developed and a hybrid mounting concept for the RLCC cells is presented. The optical performance of different CPC materials was tested and analysed in this work. Finally, small modules consisting of six series interconnected RLCC cells and six CPCs were integrated into the concentrator system and tested outdoor. A system efficiency of 16.2% was reached at around 800 W/m2 direct irradiance under realistic outdoor conditions. (orig.)

Dish concentrators for solar thermal energy - Status and technology development

Science.gov (United States)

Jaffe, L. D.

1981-01-01

Comparisons are presented of point-focusing, or 'dish' solar concentrator system features, development status, and performance levels demonstrated to date. In addition to the requirements of good optical efficiency and high geometric concentration ratios, the most important future consideration in solar thermal energy dish concentrator design will be the reduction of installed and lifetime costs, as well as the materials and labor costs of production. It is determined that technology development initiatives are needed in such areas as optical materials, design wind speeds and wind loads, structural configuration and materials resistance to prolonged exposure, and the maintenance of optical surfaces. The testing of complete concentrator systems, with energy-converting receivers and controls, is also necessary. Both reflector and Fresnel lens concentrator systems are considered.

Increase in serum albumin concentration is associated with prediabetes development and progression to overt diabetes independently of metabolic syndrome.

Science.gov (United States)

Jun, Ji Eun; Lee, Seung-Eun; Lee, You-Bin; Jee, Jae Hwan; Bae, Ji Cheol; Jin, Sang-Man; Hur, Kyu Yeon; Lee, Moon-Kyu; Kim, Jae Hyeon

2017-01-01

Serum albumin concentration is associated with both type 2 diabetes and metabolic syndrome (MetS). We sought to investigate whether baseline serum albumin and change in serum albumin could be independent risk factors for prediabetes in subjects without MetS. We further examined the effect of serum albumin on progression to overt diabetes in subjects who developed prediabetes. Among 10,792 participants without diabetes and MetS who consecutively underwent yearly health check-ups over six years, 9,807 subjects without incident MetS were enrolled in this longitudinal retrospective study. The risk of developing prediabetes (impared fasting glucose or hemoglobin A1c) was analyzed according to baseline and percent change in serum albumin concentration using Cox regression analysis. Serial changes in serum albumin concentration were measured from baseline to one year before prediabetes diagnosis, and then from the time of prediabetes diagnosis to progression to overt diabetes or final follow-up. A total of 4,398 incident cases of prediabetes developed during 35,807 person-years (median 3.8 years). The hazard ratio for incident prediabetes decreased as percent change in serum albumin concentration (quartiles and per 1%) increased in a crude and fully adjusted model. However, baseline serum albumin concentration itself was not associated with prediabetic risk. Serum albumin levels kept increasing until the end of follow-up in prediabetic subjects who returned to normal glycemic status, whereas these measures did not change in prediabetic subjects who developed type 2 diabetes. Serum albumin concentration measured at the end of follow-up was the highest in the regression group, compared to the stationary (p = 0.014) or progression groups (p = 0.009). Increase in serum albumin concentration might protect against early glycemic deterioration and progression to type 2 diabetes even in subjects without MetS.

Final report of advisory subcommittee on development of JENDL. Guideline for developing next JENDL

International Nuclear Information System (INIS)

Chiba, Go

2016-01-01

An advisory subcommittee on development of JENDL was established in 2013 to discuss future development of JENDL among experts on nuclear data experiments, evaluations and applications. This paper is a summary of a final report which was submitted to the JENDL committee on March in 2014. (author)

Simulation and development of a multi-leg homogeniser concentrating assembly for concentrated photovoltaic (CPV) system with electrical rating analysis

KAUST Repository

Burhan, Muhammad

2016-03-09

Concentrated photovoltaic (CPV) system utilizing multi-junction solar cells, is the main focus for current research, offering highest efficiency among all photovoltaic systems. The main aspect of CPV system is the design and performance of concentrating assembly, as it determines the performance of whole CPV system. However, the conventional design of CPV concentrating assembly dedicates one concentrator for each solar cell, in which single concentrator is capable to concentrate solar radiation onto single solar cell. This paper proposes a novel concentrating assembly for CPV system, which is designed to concentrate solar radiation onto four multi-junction solar cells with a single set of concentrators. The proposed design not only can reduce the number of concentrators and assembly efforts for CPV systems, but also achieved an acceptance angle of 1°. In this paper, the proposed multi-leg homogeniser CPV concentrating assembly is designed, developed, experimentally tested and verified through ray tracing simulation. The paper also discuss the development of mini, precise and accurate but cost effective two axis solar tracker for CPV system, which can be installed at any location even at rooftop of residential buildings, unlike conventional large scale CPV systems. Moreover, through the electrical rating analysis of the developed CPV system, its performance can be accurately estimated in any region. © 2016 Elsevier Ltd. All rights reserved.

Simulation and development of a multi-leg homogeniser concentrating assembly for concentrated photovoltaic (CPV) system with electrical rating analysis

KAUST Repository

Burhan, Muhammad; Chua, Kian Jon Ernest; Ng, Kim Choon

2016-01-01

Concentrated photovoltaic (CPV) system utilizing multi-junction solar cells, is the main focus for current research, offering highest efficiency among all photovoltaic systems. The main aspect of CPV system is the design and performance of concentrating assembly, as it determines the performance of whole CPV system. However, the conventional design of CPV concentrating assembly dedicates one concentrator for each solar cell, in which single concentrator is capable to concentrate solar radiation onto single solar cell. This paper proposes a novel concentrating assembly for CPV system, which is designed to concentrate solar radiation onto four multi-junction solar cells with a single set of concentrators. The proposed design not only can reduce the number of concentrators and assembly efforts for CPV systems, but also achieved an acceptance angle of 1°. In this paper, the proposed multi-leg homogeniser CPV concentrating assembly is designed, developed, experimentally tested and verified through ray tracing simulation. The paper also discuss the development of mini, precise and accurate but cost effective two axis solar tracker for CPV system, which can be installed at any location even at rooftop of residential buildings, unlike conventional large scale CPV systems. Moreover, through the electrical rating analysis of the developed CPV system, its performance can be accurately estimated in any region. © 2016 Elsevier Ltd. All rights reserved.

Development of an instrument to measure the concentration of noncondensable gases in geothermal discharges. Final report, October 1, 1978-September 30, 1979

Energy Technology Data Exchange (ETDEWEB)

Blair, C.K.; Harrison, R.F.

1980-01-01

Reported herein is a summary of a project to design, construct, and test a device which will continuously measure the vapor phase concentration of noncendensable gases in saturated steam/water geothermal discharges. Descriptions of the design, operating procedures, measurement accuracy, and limitations of the device are included. Also presented are results of laboratory testing and of field demonstration of the instrument. Recommendations for further refinement and development of the apparatus are discussed.

Final Report. Center for Scalable Application Development Software

Energy Technology Data Exchange (ETDEWEB)

Mellor-Crummey, John [Rice Univ., Houston, TX (United States)

2014-10-26

The Center for Scalable Application Development Software (CScADS) was established as a part- nership between Rice University, Argonne National Laboratory, University of California Berkeley, University of Tennessee – Knoxville, and University of Wisconsin – Madison. CScADS pursued an integrated set of activities with the aim of increasing the productivity of DOE computational scientists by catalyzing the development of systems software, libraries, compilers, and tools for leadership computing platforms. Principal Center activities were workshops to engage the research community in the challenges of leadership computing, research and development of open-source software, and work with computational scientists to help them develop codes for leadership computing platforms. This final report summarizes CScADS activities at Rice University in these areas.

Photovoltaic concentrator technology development project. Sixth project integration meeting

Energy Technology Data Exchange (ETDEWEB)

None

1980-10-01

Thirty-three abstracts and short papers are presented which describe the current status of research, development, and demonstration of concentrator solar cell technology. Solar concentrators discussed include the parabolic trough, linear focus Fresnel lens, point focus Fresnel lens, and the parabolic dish. Solar cells studied include silicon, GaAs, and AlGaAs. Research on multiple junction cells, combined photovoltaic/thermal collectors, back contact solar cells, and beam splitter modules is described. Concentrator solar cell demonstration programs are reported. Contractor status summaries are given for 33 US DOE concentrator solar cell contracts; a description of the project, project status, and key results to date is included. (WHK)

Thayer Lake Hydropower Development -- Final Report

Energy Technology Data Exchange (ETDEWEB)

Matousek, Mark [ORENCO Hydropower, Palo Alto, CA (United States)

2017-06-30

The Thayer Lake Hydropower Development (THLD) has been under study since the late 1970’s as Angoon explored opportunities to provide lower cost renewable power to the Community and avoid the high cost of diesel generation. Kootznoowoo Inc. (Kootznoowoo), the tribal corporation for Angoon’s current and past residents, was provided the rights by Congress to develop a hydropower project within the Admiralty Island National Monument. This grant (DE-EE0002504) by the Department of Energy’s (DOE’s) Office of Indian Energy and a matching grant from the Alaska Energy Authority (AEA) were provided to Kootznoowoo to enable the design, engineering and permitting of this hydropower project on Thayer Creek. Prior to the grant, the USFS had performed a final environmental impact statement (FEIS) and issued a Record of Decision (ROD) in 2009 for a 1.2 MW hydropower project on Thayer Creek that would Angoon’s needs with substantial excess capacity for growth. Kootznoowoo hired Alaska Power & Telephone (AP&T) in 2013 to manage this project and oversee its development. AP&T and its subcontractors under Kootznoowoo’s guidance performed several activities, aligned with the task plan defined in the grant.

Programmable SAW development :Sandia/NASA project final report.

Energy Technology Data Exchange (ETDEWEB)

Brocato, Robert Wesley

2004-10-01

This report describes a project to develop both fixed and programmable surface acoustic wave (SAW) correlators for use in a low power space communication network. This work was funded by NASA at Sandia National Laboratories for fiscal years 2004, 2003, and the final part of 2002. The role of Sandia was to develop the SAW correlator component, although additional work pertaining to use of the component in a system and system optimization was also done at Sandia. The potential of SAW correlator-based communication systems, the design and fabrication of SAW correlators, and general system utilization of those correlators are discussed here.

Freeze concentration of dairy products Phase 2. Final report

Energy Technology Data Exchange (ETDEWEB)

Best, D.E.; Vasavada, K.C.

1993-09-01

An efficient, electrically driven freeze concentration system offers potential for substantially increasing electricity demand while providing the mature dairy industry with new products for domestic and export markets together with enhanced production efficiencies. Consumer tests indicate that dairy products manufactured from freeze-concentrated ingredients are either preferred or considered equivalent in quality to fresh milk-based products. Economic analyses indicate that this technology should be competitive with thermal evaporation processes on a commercial basis.

The development of sectoral final and basic energy demand in the Federal Republic of Germany

International Nuclear Information System (INIS)

Reents, H.

1977-08-01

The detailed knowledge of the demand structures and their determining factors is an important precondition for estimating the possible developments of future energy demand. In this report the past developments of the final and basic energy demand in the different demand categories private households, commercial sector, industry and transportation will be analyzed. The demonstrated relations are the basis for a final energy demand model. With the help of this model a scenario of the future development of the final energy demand in the different sectors will be built. It is the aim of this scenario to show, how alternative actions (insulation, gas-heat pump) influence the future development of the final energy demand. (orig.) [de

77 FR 45944 - Final Priorities and Definitions; State Personnel Development Grants

Science.gov (United States)

2012-08-02

.... Discussion: OSEP agrees that the use of technology can improve the delivery of professional development in... distance education technology for providing professional development to remote areas. Discussion: OSEP... DEPARTMENT OF EDUCATION 34 CFR Chapter III Final Priorities and Definitions; State Personnel...

Dish concentrators for solar thermal energy: Status and technology development

Science.gov (United States)

Jaffe, L. D.

1982-01-01

Point-focusing concentrators under consideration for solar thermal energy use are reviewed. These concentrators differ in such characteristics as optical configuration, optical materials, structure for support of the optical elements and of the receiver, mount, foundation, drive, controls and enclosure. Concentrator performance and cost are considered. Technology development is outlined, including wind loads and aerodynamics; precipitation, sand, and seismic considerations; and maintenance and cleaning.

Final report: Compiled MPI. Cost-Effective Exascale Application Development

Energy Technology Data Exchange (ETDEWEB)

Gropp, William Douglas [Univ. of Illinois, Urbana-Champaign, IL (United States)

2015-12-21

This is the final report on Compiled MPI: Cost-Effective Exascale Application Development, and summarizes the results under this project. The project investigated runtime enviroments that improve the performance of MPI (Message-Passing Interface) programs; work at Illinois in the last period of this project looked at optimizing data access optimizations expressed with MPI datatypes.

Development of a wide-range tritium-concentration detector

International Nuclear Information System (INIS)

Jun, F.; Zhe, L.; Shicheng, L.; Jiangfeng, S.; Deli, L.

2015-01-01

According to the requirements of the tritium related systems of the TBM (Test Blanket Module) for monitoring the on-line tritium concentration, a wide-range tritium-concentration detector has been developed to measure the tritium concentration in the range of 10 4 Bq/ml - 5*10 8 Bq/ml. This detector is combined with a low-memory helium ionization chamber. The weak current signal collected in the ionization chamber is converted to the voltage signal by an I-V converter. The minimum weak current which the detector could be measured is 10 -14 A. The performance of the background current and the current response linearity of the prototype have been tested. The test result indicates that the linear response of the current signal of the prototype without connecting the ionization chamber is good. The linear correlation coefficient is R 2 = 0.998

The impact of bone development on final carcass weight

DEFF Research Database (Denmark)

Tatara, M.R.; Tygesen, Malin Plumhoff; Sawa-Wojtanowicz, B.

2006-01-01

Proper development and function of the skeleton is crucial for the optimal growth of an organism, with rapid growth rates often resulting in skeletal disorders in farm animals. Yet, despite clear benefits for breed selection and animal welfare (HARRISON et al., 2004), the impact of bone development...... was removed and its parameters correlated with carcass weight. Results suggest that both femur length and femur weight act as good predictors of final carcass weight in lambs. However, no effect of paternal genetics, on the femur to carcass correlations, was noted....

Development of a wide-range tritium-concentration detector

Energy Technology Data Exchange (ETDEWEB)

Jun, F.; Zhe, L.; Shicheng, L.; Jiangfeng, S.; Deli, L. [China Academy of Engineering Physics, Mianyang (China)

2015-03-15

According to the requirements of the tritium related systems of the TBM (Test Blanket Module) for monitoring the on-line tritium concentration, a wide-range tritium-concentration detector has been developed to measure the tritium concentration in the range of 10{sup 4} Bq/ml - 5*10{sup 8} Bq/ml. This detector is combined with a low-memory helium ionization chamber. The weak current signal collected in the ionization chamber is converted to the voltage signal by an I-V converter. The minimum weak current which the detector could be measured is 10{sup -14} A. The performance of the background current and the current response linearity of the prototype have been tested. The test result indicates that the linear response of the current signal of the prototype without connecting the ionization chamber is good. The linear correlation coefficient is R{sup 2} = 0.998.

Final Stage Development of Reactor Console Simulator

International Nuclear Information System (INIS)

Mohamad Idris Taib; Ridzuan Abdul Mutalib; Zareen Khan Abdul Jalil Khan; Mohd Khairulezwan Abdul Manan; Mohd Sabri Minhat; Nurfarhana Ayuni Joha

2013-01-01

The Reactor Console Simulator PUSPATI TRIGA Reactor was developed since end of 2011 and now in the final stage of development. It is will be an interactive tool for operator training and teaching of PUSPATI TRIGA Reactor. Behavior and characteristic for reactor console and reactor itself can be evaluated and understand. This Simulator will be used as complement for actual present reactor console. Implementation of human system interface (HSI) is using computer screens, keyboard and mouse. Multiple screens are used to match the physical of present reactor console. LabVIEW software are using for user interface and mathematical calculation. Polynomial equation based on control rods calibration data as well as operation parameters record was used to calculate and estimated reactor console parameters. The capabilities in user interface, reactor physics and thermal-hydraulics can be expanded and explored to simulation as well as modeling for New Reactor Console, Research Reactor and Nuclear Power Plant. (author)

Research and development on super heat pump energy accumulation system. Final report

Energy Technology Data Exchange (ETDEWEB)

NONE

1993-06-01

This is the final report on research and development of super heat pump energy accumulation system, which has been carried out from FY 1985 to 1992. It describes outline of the research and development program, R and D results, final evaluation methodology, evaluation of the R and D, proposals for the commercialization, and so on. The super high performance compression heat pumps are technically evaluated for highly efficient type (for heating, and cooling and heating), high temperature type (utilizing high temperature heat source, and low temperature heat source), working fluids (alcohol-based and nonalcohol-based), stainless steel plate fin type heat exchanger, EHD heat exchanger, and so on. The other techniques evaluated include those for chemical heat storage, combined systems, plant simulation, and systemization. The evaluation works are also directed to the economic and environmental aspects. Finally, the R and D themes are proposed to leap over various hurdles, e.g., reliability and economic viability, for the eventual commercialization of the energy accumulation system. (NEDO)

Molten Salt-Carbon Nanotube Thermal Energy Storage for Concentrating Solar Power Systems Final Report

Energy Technology Data Exchange (ETDEWEB)

Michael Schuller; Frank Little; Darren Malik; Matt Betts; Qian Shao; Jun Luo; Wan Zhong; Sandhya Shankar; Ashwin Padmanaban

2012-03-30

We demonstrated that adding nanoparticles to a molten salt would increase its utility as a thermal energy storage medium for a concentrating solar power system. Specifically, we demonstrated that we could increase the specific heat of nitrate and carbonate salts containing 1% or less of alumina nanoparticles. We fabricated the composite materials using both evaporative and air drying methods. We tested several thermophysical properties of the composite materials, including the specific heat, thermal conductivity, latent heat, and melting point. We also assessed the stability of the composite material with repeated thermal cycling and the effects of adding the nanoparticles on the corrosion of stainless steel by the composite salt. Our results indicate that stable, repeatable 25-50% improvements in specific heat are possible for these materials. We found that using these composite salts as the thermal energy storage material for a concentrating solar thermal power system can reduce the levelized cost of electricity by 10-20%. We conclude that these materials are worth further development and inclusion in future concentrating solar power systems.

Effect of Concentrated Language Encounter Method in Developing ...

African Journals Online (AJOL)

The paper examined the effect of concentrated language encounter method in developing sight word recognition skill in primary school pupils in cross river state. The purpose of the study was to find out the effect of Primary One pupils' reading level, English sight word recognition skill. It also examine the extent to which the ...

What Do Final Year Engineering Students Know about Sustainable Development?

Science.gov (United States)

Nicolaou, I.; Conlon, E.

2012-01-01

This paper presents data from a project that aims to determine the level of knowledge and understanding of engineering students about sustainable development (SD). The data derive from a survey completed by final year engineering students in three Irish Higher Education Institutions. This paper is part of a larger study that examines the…

Development of High-Performance Cast Crankshafts. Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Bauer, Mark E [General Motors, Detroit, MI (United States)

2017-03-31

The objective of this project was to develop technologies that would enable the production of cast crankshafts that can replace high performance forged steel crankshafts. To achieve this, the Ultimate Tensile Strength (UTS) of the new material needs to be 850 MPa with a desired minimum Yield Strength (YS; 0.2% offset) of 615 MPa and at least 10% elongation. Perhaps more challenging, the cast material needs to be able to achieve sufficient local fatigue properties to satisfy the durability requirements in today’s high performance gasoline and diesel engine applications. The project team focused on the development of cast steel alloys for application in crankshafts to take advantage of the higher stiffness over other potential material choices. The material and process developed should be able to produce high-performance crankshafts at no more than 110% of the cost of current production cast units, perhaps the most difficult objective to achieve. To minimize costs, the primary alloy design strategy was to design compositions that can achieve the required properties with minimal alloying and post-casting heat treatments. An Integrated Computational Materials Engineering (ICME) based approach was utilized, rather than relying only on traditional trial-and-error methods, which has been proven to accelerate alloy development time. Prototype melt chemistries designed using ICME were cast as test specimens and characterized iteratively to develop an alloy design within a stage-gate process. Standard characterization and material testing was done to validate the alloy performance against design targets and provide feedback to material design and manufacturing process models. Finally, the project called for Caterpillar and General Motors (GM) to develop optimized crankshaft designs using the final material and manufacturing processing path developed. A multi-disciplinary effort was to integrate finite element analyses by engine designers and geometry-specific casting

Development of system on predicting uranium concentration from pregnant solution

International Nuclear Information System (INIS)

Yi Weiping

2004-01-01

Uranium concentration from pregnant solution is primary index of process for in-situ leaching of uranium, and the suitable method with which to predicate this index and effective means to solve it with were continuously studied hard. SPUC-system on predicting uranium concentration based on GM model of gray system theory is developed, and the mathematical model, constitution, function and theory foundation of this system are introduced. (authors)

Development on the cryogenic hydrogen isotopes distillation process technology for tritium removal (Final report)

International Nuclear Information System (INIS)

Sung, Ki Woung; Kim, Yong Ik; Na, Jeong Won; Ku, Jae Hyu; Kim, Kwang Rak; Jeong, Yong Won; Lee, Han Soo; Cho, Young Hyun; Ahn, Do Hee; Baek, Seung Woo; Kang, Hee Seok; Kim, You Sun

1995-12-01

While tritium exposure to the site-workers in Wolsung NPP is up to about 40% of the total personnel exposure, Ministry of Science and Technology has asked tritium removal facility for requirement of post heavy-water reactor construction. For the purpose of essential removal of tritium from the Wolsung heavy-water reactor system, a preliminary study on the cryogenic Ar-N 2 and H 2 -D 2 distillation process for development of liquid-phase catalytic exchange cryogenic hydrogen distillation process technology. The Ar-N 2 distillation column showed good performance with approximately 97% of final Ar concentration, and a computer simulation code was modified using these data. A simulation code developed for cryogenic hydrogen isotopes (H 2 , HD, D 2 , HT, DT, T 2 ) distillation column showed good performance after comparison with the result of a JAERI code, and a H 2 -D 2 distillation column was made. Gas chromatography for hydrogen isotopes analysis was established using a vacuum sampling loop, and a schematic diagram of H 2 -D 2 distillation process was suggested. A feasibility on modification of H 2 -D 2 distillation process control system using Laser Raman Spectroscopy was studied, and the consideration points for tritium storage system for Wolsung tritium removal facility was suggested. 31 tabs., 79 figs., 68 refs. (Author)

Development status of the PDC-1 Parabolic Dish Concentrator

Science.gov (United States)

Thostesen, T.; Soczak, I. F.; Pons, R. L.

1982-01-01

The status of development of the 12 m diameter parabolic dish concentrator which is planned for use with the Small Community Solar Thermal Power System. The PDC-1 unit features the use of plastic reflector film bonded to structural plastic gores supported by front-bracing steel ribs. An elevation-over-azimuth mount arrangement is employed, with a conventional wheel-and-track arrangement; outboard trunnions permit the dish to be stored in the face down position, with the added advantage of easy access to the power conversion assembly. The control system is comprised of a central computer (LSI 1123), a manual control panel, a concentrator control unit, two motor controllers, a Sun sensor, and two angular position resolvers. The system is designed for the simultaneous control of several concentrators. The optical testing of reflective panels is described.

Influence of the size of facets on point focus solar concentrators

Energy Technology Data Exchange (ETDEWEB)

Riveros-Rosas, David [Instituto de Geofisica, Universidad Nacional Autonoma de Mexico, Ciudad Universitaria, Col. Copilco, Coyoacan, CP 04510 DF (Mexico); Sanchez-Gonzalez, Marcelino [Centro Nacional de Energias Renovables, c/Somera 7-9, CP 28026 Madrid (Spain); Arancibia-Bulnes, Camilo A.; Estrada, Claudio A. [Centro de Investigacion en Energia, Universidad Nacional Autonoma de Mexico, Priv. Xochicalco s/n, Morelos (Mexico)

2011-03-15

It is a common practice in the development of point focus solar concentrators to use multiple identical reflecting facets, as a practical and economic alternative for the design and construction of large systems. This kind of systems behaves in a different manner than continuous paraboloidal concentrators. A theoretical study is carried out to understand the effect of the size of facets and of their optical errors in multiple facet point focus solar concentrating systems. For this purpose, a ray tracing program was developed based on the convolution technique, in which the brightness distribution of the sun and the optical errors of the reflecting surfaces are considered. The study shows that both the peak of concentration and the optimal focal distance of the system strongly depend on the size of the facets, and on their optical errors. These results are useful to help concentrator developers to have a better understanding of the relationship between manufacturing design restrictions and final optical behavior. (author)

ADVANCED TURBINE SYSTEM CONCEPTUAL DESIGN AND PRODUCT DEVELOPMENT; FINAL

International Nuclear Information System (INIS)

Albrecht H. Mayer

2000-01-01

Asea Brown Boveri (ABB) has completed its technology based program. The results developed under Work Breakdown Structure (WBS) 8, concentrated on technology development and demonstration have been partially implemented in newer turbine designs. A significant improvement in heat rate and power output has been demonstrated. ABB will use the knowledge gained to further improve the efficiency of its Advanced Cycle System, which has been developed and introduced into the marked out side ABB's Advanced Turbine System (ATS) activities. The technology will lead to a power plant design that meets the ATS performance goals of over 60% plant efficiency, decreased electricity costs to consumers and lowest emissions

Engineering development of advanced froth flotation. Volume 2, Final report

Energy Technology Data Exchange (ETDEWEB)

Ferris, D.D.; Bencho, J.R.; Torak, E.R. [ICF Kaiser Engineers, Inc., Pittsburgh, PA (United States)

1995-03-01

This report is an account of findings related to the Engineering and Development of Advanced Froth Flotation project. The results from benchscale and proof-of-concept (POC) level testing are presented and the important results from this testing are used to refine a conceptual design and cost estimate for a 20 TPH Semi-Works Facility incorporating the final proposed technology.

NDE reliability and SAFT-UT final development

International Nuclear Information System (INIS)

Doctor, S.R.; Deffenbaugh, J.D.; Good, M.S.; Green, E.R.; Heasler, P.G.; Reid, L.D.; Simonen, F.A.; Spanner, J.C.; Taylor, T.T.; Vo, T.V.

1990-01-01

The Evaluation and Improvement of NDE Reliability for Inservice Inspection of Light Water Reactors (NDE Reliability) program at the Pacific Northwest Laboratory (PNL) was established by the US Nuclear Regulatory Commission (NRC) to determine the reliability of current inservice inspection (ISI) techniques and to develop recommendations that will ensure a suitably high inspection reliability. This is a progress report covering the programmatic work from October 1987 through September 1988. The program for Validation and Technology Transfer for SAFT-UT is designed to accomplish the final step of moving research results into beneficial application. Accomplishments for FY88 in Synthetic Aperture Focusing of Ultrasonic Test data (SAFT-UT) under this program are discussed in this paper. The information is treated under the copies of Code Activities, Field Validation, and Seminars. (orig.)

Lime, agent to uranium concentration; La chaux comme agent de concentration de l'uranium

Energy Technology Data Exchange (ETDEWEB)

Mouret, P; Le Bris, J; Kremer, M [Commissariat a l' Energie Atomique, Saclay (France). Centre d' Etudes Nucleaires; Gautier, R [Etablissement Kuhlmann, Service d' Etudes et de Pilotages Industriels (France)

1958-07-01

Choice of the process according to health requirements. Description of the process: dissolution of uranium by sulfuric leaching of ores, precipitation of uranium by lime, re-dissolution of the concentrate with nitric ions, purification by T.B.P. finally resulting in pure uranyl nitrate solution containing 400 g/litre. (author)Fren. [French] Les raisons du choix du procede en fonction des imperatifs d'hygiene, sont exposees ainsi que le procede qui consiste en une dissolution de l'uranium des minerais par lixiviation sulfurique, precipitation de l'uranium par la chaux et redissolution du concentre en presence d'ions nitriques, purification par le T.B.P. et obtention d'un concentre final de nitrate d'uranyle pur a 400 g/litre. (auteur)

Rock grouting. Current competence and development for the final repository

International Nuclear Information System (INIS)

Emmelin, Ann; Brantberger, Martin; Eriksson, Magnus; Gustafson, Gunnar; St ille, Haakan

2007-06-01

The report aims at presenting the overall state of grouting competence and development relating to the final repository and at motivating and giving detail to the grouting sections presented in the 2007 version of the overall SKB report 'Programme for research, development and demonstration of methods for the management and disposal of nuclear waste' that is presented to the government every three years. The report offers suggestions for principles for planning, design and execution of grouting and describes the further work thought to be necessary in order to meet the requirements of the final repository, that are currently given as working premises. This report does not aim to, and cannot, describe the grouting processes in detail. For details of current concepts, experience and development work, a list of references is provided. In Chapter 2, the task of sealing the underground repository is examined and an overall approach presented. Although the requirements related to this task are preliminary, it is made evident that they concern both the actual grouting results and the process leading to the achievement of these results. Chapter 3 is a conceptual description of grouting and the factors that govern the spreading of grout in the rock mass. It is intended as an introduction to Chapters 4-6, which describe the state of grouting competence and the tools available for the sealing of the final repository facility. Both common practice and cutting-edge research are dealt with in these chapters, mainly relying on references where available. Chapters 4 and 5 focus on the system consisting of the fundamental components the rock mass, the grout materials and the grouting technology, and how these system components interact whilst, in Chapter 6, the rock/grout technical system is viewed in a brief organizational context. Based on the requirements on results and the overall grouting process on the one hand and the current competence in grouting theory and practice on the

Rock grouting. Current competence and development for the final repository

Energy Technology Data Exchange (ETDEWEB)

Emmelin, Ann (Swedish Nuclear Fuel and Waste Management Co., Stockholm (SE)); Brantberger, Martin (Ramboell (SE)); Eriksson, Magnus (Vattenfall Power Consultant (SE)); Gustafson, Gunnar (Chalmers Univ. of Technology, Goeteborg (SE)); Stille, Haakan (Royal Inst. of Technology, Stockholm (SE))

2007-06-15

The report aims at presenting the overall state of grouting competence and development relating to the final repository and at motivating and giving detail to the grouting sections presented in the 2007 version of the overall SKB report 'Programme for research, development and demonstration of methods for the management and disposal of nuclear waste' that is presented to the government every three years. The report offers suggestions for principles for planning, design and execution of grouting and describes the further work thought to be necessary in order to meet the requirements of the final repository, that are currently given as working premises. This report does not aim to, and cannot, describe the grouting processes in detail. For details of current concepts, experience and development work, a list of references is provided. In Chapter 2, the task of sealing the underground repository is examined and an overall approach presented. Although the requirements related to this task are preliminary, it is made evident that they concern both the actual grouting results and the process leading to the achievement of these results. Chapter 3 is a conceptual description of grouting and the factors that govern the spreading of grout in the rock mass. It is intended as an introduction to Chapters 4-6, which describe the state of grouting competence and the tools available for the sealing of the final repository facility. Both common practice and cutting-edge research are dealt with in these chapters, mainly relying on references where available. Chapters 4 and 5 focus on the system consisting of the fundamental components the rock mass, the grout materials and the grouting technology, and how these system components interact whilst, in Chapter 6, the rock/grout technical system is viewed in a brief organizational context. Based on the requirements on results and the overall grouting process on the one hand and the current competence in grouting theory and

Early prenatal vitamin D concentrations and social-emotional development in infants.

Science.gov (United States)

Chawla, Devika; Fuemmeler, Bernard; Benjamin-Neelon, Sara E; Hoyo, Cathrine; Murphy, Susan; Daniels, Julie L

2017-12-04

Many pregnant women in the United States have suboptimal vitamin D, but the impact on infant development is unclear. Moreover, no pregnancy-specific vitamin D recommendations have been widely accepted. Given the ubiquitous expression of vitamin D receptors in the brain, we investigated the association between early prenatal plasma 25-hydroxyvitamin D (25(OH)D) concentrations and children's social and emotional development in the Newborn Epigenetic Study, a prospective study of pregnancies from 2009 to 2011 in Durham, North Carolina. We measured 25(OH)D concentrations in first or second trimester plasma samples and categorized 25(OH)D concentrations into quartiles. Covariates were derived from maternal questionnaires. Mothers completed the Infant Toddler Social-Emotional Development Assessment when children were 12-24 months of age. We used multivariable linear regression to evaluate associations between 25(OH)D and specific behavior scores, adjusted for season of blood draw, maternal age, education, parity, smoking, marital status, prepregnancy BMI, and infant gender. We investigated effect-measure modification by race/ethnicity. Of the 218 mother-infant pairs with complete data, Black mothers had much lower 25(OH)D concentrations as compared to White and Hispanic mothers. After adjustment, lower prenatal 25(OH)D was associated with slightly higher (less favorable) Internalizing scores among White children, but lower (more favorable) Internalizing scores among Black and Hispanic children. Lower prenatal 25(OH)D also appears to be associated with higher (less favorable) dysregulation scores, though only among White and Hispanic children. Though imprecise, preliminary results warrant further investigation regarding a role for prenatal vitamin D on children's early social and emotional development.

Development of cancer therapy facility of HANARO and medical research in BNCT; development of the technique for boron concentration analysis

Energy Technology Data Exchange (ETDEWEB)

Choi, Hee Dong; Byun, Soo Hyun; Sun, Gwang Min; Kim, Suk Kwon; Kim, In Jung; Park, Chang Su [Seoul National University, Seoul (Korea)

2002-03-01

Objective and Necessity of the Project- Development of a boron concentration analysis facility used for BNCT. - Development of the technique for boron concentration analysis. Contents and Scopes of the Project - Construction of the boron concentration analysis facility based on PGAA. Estimation of the neutron beam characteristics. -Establishment of the technique for the boron concentration analysis. - Estimation of the reliability for the boron analysis. Results of the Project -Installation of the boron concentration analysis facility at Hanaro. - Neutron beam characteristics are the sample position (neutron flux : 7.9 x 10{sup 7} n/cm{sup 2}s, Cd-ratio : 266) Technique for the boron concentration analysis. - Boron detection sensitivity and limit (detection sensitivity : 2, 131 cps/mg-B, detection limit : 67 ng for 10,000 sec). 63 refs., 37 figs., 13 tabs. (Author)

Development on the cryogenic hydrogen isotopes distillation process technology for tritium removal (Final report)

Energy Technology Data Exchange (ETDEWEB)

Sung, Ki Woung; Kim, Yong Ik; Na, Jeong Won; Ku, Jae Hyu; Kim, Kwang Rak; Jeong, Yong Won; Lee, Han Soo; Cho, Young Hyun; Ahn, Do Hee; Baek, Seung Woo; Kang, Hee Seok; Kim, You Sun [Korea Atomic Energy Research Institute, Taejon (Korea, Republic of)

1995-12-01

While tritium exposure to the site-workers in Wolsung NPP is up to about 40% of the total personnel exposure, Ministry of Science and Technology has asked tritium removal facility for requirement of post heavy-water reactor construction. For the purpose of essential removal of tritium from the Wolsung heavy-water reactor system, a preliminary study on the cryogenic Ar-N{sub 2} and H{sub 2}-D{sub 2} distillation process for development of liquid-phase catalytic exchange cryogenic hydrogen distillation process technology. The Ar-N{sub 2} distillation column showed good performance with approximately 97% of final Ar concentration, and a computer simulation code was modified using these data. A simulation code developed for cryogenic hydrogen isotopes (H{sub 2}, HD, D{sub 2}, HT, DT, T{sub 2}) distillation column showed good performance after comparison with the result of a JAERI code, and a H{sub 2}-D{sub 2} distillation column was made. Gas chromatography for hydrogen isotopes analysis was established using a vacuum sampling loop, and a schematic diagram of H{sub 2}-D{sub 2} distillation process was suggested. A feasibility on modification of H{sub 2}-D{sub 2} distillation process control system using Laser Raman Spectroscopy was studied, and the consideration points for tritium storage system for Wolsung tritium removal facility was suggested. 31 tabs., 79 figs., 68 refs. (Author).

Development and evaluation of SBLINE, a suite of models for the prediction of pollution concentrations from vehicles in urban areas

Energy Technology Data Exchange (ETDEWEB)

Namdeo, A.K.; Colls, J.J. [Environmental Science, University of Nottingham, Loughborough (United Kingdom)

1996-09-06

The assessment of air quality impacts from roadways is a major concern to urban planners, developers, health officials and engineers. This paper describes the development of a suite of models, called SBLINE, for prediction of pollution concentrations from vehicles in urban road networks. The first component of the suite is ROADFAC, an emission model for calculating emission rates for a road link with known vehicle fleet structure and operational details. ROADFAC can also calculate modal emission rates, caused by deceleration, idle, acceleration and cruise operational modes, by determining queue length and vehicle delay from traffic volume and signal phasing information. The other components of SBLINE are two dispersion models, called NOTLINE and CPB, for prediction of pollution concentrations contributed by different roadlinks in the network. These models use site geometry, meteorology, and traffic emissions calculated by ROADFAC to predict pollutant concentrations. The contribution from a given link is calculated by using NOTLINE if that link is situated in simple topography, or CPB is run if the link is inside a canyon or a cut-section. Finally, cumulative concentrations at any receptor location are calculated by adding the contributions from all roadlinks. SBLINE can be applied to any urban network of roads, with roadlinks located in either simple topography or street canyons. The program has been evaluated in one region of Leicester in the UK. The region represents a typical urban network of roads with some roads located in plain topography and some inside medium size canyons. Observed values of pollutant concentrations are compared with predictions made from detailed measurements of the vehicle population parameters, meteorology, and local street and building topography. Well-established statistical techniques have been used to show the potential of SBLINE for application to other road networks

Development of a 10 Hz measurement system for atmospheric aerosol concentration

International Nuclear Information System (INIS)

Bouarouri, Assia

2014-01-01

The goal is to develop an aerosol charger based on a corona discharge for atmospheric concentration measurements (10 3 -10 5 cm -3 ) within a response time of 100 ms. Two ion sources, point-to-hole and wire-to-slit have been characterized. The increase of the ion flow in the post-discharge by EHD ion confinement in both the discharge gap and the hole has been shown. At first, using an experimental survey driven in two mixing configurations, concentric and face-to-face, we have confirmed the aerosol diffusion charging law which depends on aerosol diameter and N i .t product, with N i , the ions concentration and t, the charging time. Thus, the originality of this charger relies on the very high heterogeneity of unipolar ion densities (N i 0 ≥10 9 cm -3 ) required to compensate the charging time of 50 ms. In these conditions, we have shown that aerosol diameter and the charging dynamic (which depends also on the diameter) control the aerosol trajectory. The chargers have, next, been compared in different operating conditions, mainly in terms of the maximal charging and the minimal losses. In the chosen charger (point-to-hole ion source and concentric mixing), the relations charge/mobility and losses according to diameter have been characterized. We have also shown the linearity of the charged particles current with the aerosol concentration which allows the current-concentration data inversion. The preliminary measurement system composed by the charger, the separator and the particle current measurements, satisfies the objectives of the study in terms of the concentration detection limit (10 3 cm -3 ) and the response time (100 ms). We have thus shown the feasibility of an atmospheric aerosol concentration measurement system at 10 Hz using a corona discharge charger provided that the separation power is improved. Furthermore, knowing that aerosol losses are negligible and the lower limit of the partial charging, the developed charger is adaptable with other

Staff Development Through the Implementation of Two Innovative Learning/Teaching Modes. Final Report.

Science.gov (United States)

Nabokov, Peter; And Others

The final report describes the generally successful development and use of two new instructional models for adult basic education (ABE): a peer instruction model and an instructional system for consumer decision making. Section 1 examines the two year application of the peer instruction model, first developed for the military, in various adult…

Development and Application of Watershed Regressions for Pesticides (WARP) for Estimating Atrazine Concentration Distributions in Streams

Science.gov (United States)

Larson, Steven J.; Crawford, Charles G.; Gilliom, Robert J.

2004-01-01

Regression models were developed for predicting atrazine concentration distributions in rivers and streams, using the Watershed Regressions for Pesticides (WARP) methodology. Separate regression equations were derived for each of nine percentiles of the annual distribution of atrazine concentrations and for the annual time-weighted mean atrazine concentration. In addition, seasonal models were developed for two specific periods of the year--the high season, when the highest atrazine concentrations are expected in streams, and the low season, when concentrations are expected to be low or undetectable. Various nationally available watershed parameters were used as explanatory variables, including atrazine use intensity, soil characteristics, hydrologic parameters, climate and weather variables, land use, and agricultural management practices. Concentration data from 112 river and stream stations sampled as part of the U.S. Geological Survey's National Water-Quality Assessment and National Stream Quality Accounting Network Programs were used for computing the concentration percentiles and mean concentrations used as the response variables in regression models. Tobit regression methods, using maximum likelihood estimation, were used for developing the models because some of the concentration values used for the response variables were censored (reported as less than a detection threshold). Data from 26 stations not used for model development were used for model validation. The annual models accounted for 62 to 77 percent of the variability in concentrations among the 112 model development stations. Atrazine use intensity (the amount of atrazine used in the watershed divided by watershed area) was the most important explanatory variable in all models, but additional watershed parameters significantly increased the amount of variability explained by the models. Predicted concentrations from all 10 models were within a factor of 10 of the observed concentrations at most

Iraqi nuclear weapons development program. Final report, October 1, 1992--September 30, 1993

International Nuclear Information System (INIS)

1993-01-01

This is an abstract of the final report focusing on the collection, collation, analysis, and recording of information pertaining to Iraqi nuclear weapons development and on the long term monitoring of Iraq

RTI photovoltaic concentrator applications experiment. Phase I. System design. Final report, 1 June 1978-28 February 1979

Energy Technology Data Exchange (ETDEWEB)

Burger, R M; Whisnant, R A; Drake, W C; Daluge, D R; Alberts, R D

1979-03-01

An experiment has been designed in which a 100 kW photovoltaic concentrator system serving the electrical load provided by an energy-efficient office-laboratory building will be built and operated in the Research Triangle Park of North Carolina. Since the purpose of the experiment is to provide the essential data for design and installation of future operational systems, the system is designed for operational flexibility. In its main operational mode, a defined primary load is diverted from the utility during all peak-demand periods. This requires the use of 1000 kWh of lead-acid batteries for energy storage. Other operational modes provide for obtaining data on peak demand reduction, on alternative battery use strategies, and on system performance with an isolated load. Operation of the system in parallel with utility-supplied power requires that the photovoltaic array outputs be inverted and that the power be controlled to achieve the operational objectives. Ten 2-axis tracking arrays consisting of 70X parabolic concentrators are used. The system will provide approximately 103 megawatt-hours of power annually to the load and the design is compatible with future retrofits including more efficient solar cells, higher concentration ratios, thermal energy collection, and other technological developments, ensuring its usefulness in research and development beyond the PRDA-35 experiment.

ADVANCED TURBINE SYSTEM CONCEPTUAL DESIGN AND PRODUCT DEVELOPMENT - Final Report

Energy Technology Data Exchange (ETDEWEB)

Albrecht H. Mayer

2000-07-15

Asea Brown Boveri (ABB) has completed its technology based program. The results developed under Work Breakdown Structure (WBS) 8, concentrated on technology development and demonstration have been partially implemented in newer turbine designs. A significant improvement in heat rate and power output has been demonstrated. ABB will use the knowledge gained to further improve the efficiency of its Advanced Cycle System, which has been developed and introduced into the marked out side ABB's Advanced Turbine System (ATS) activities. The technology will lead to a power plant design that meets the ATS performance goals of over 60% plant efficiency, decreased electricity costs to consumers and lowest emissions.

Quality control in the development of coagulation factor concentrates.

Science.gov (United States)

Snape, T J

1987-01-01

Limitation of process change is a major factor contributing to assurance of quality in pharmaceutical manufacturing. This is particularly true in the manufacture of coagulation factor concentrates, for which presumptive testing for poorly defined product characteristics is an integral feature of finished product quality control. The development of new or modified preparations requires that this comfortable position be abandoned, and that the effect on finished product characteristics of changes to individual process steps (and components) be assessed. The degree of confidence in the safety and efficacy of the new product will be determined by, amongst other things, the complexity of the process alteration and the extent to which the results of finished product tests can be considered predictive. The introduction of a heat-treatment step for inactivation of potential viral contaminants in coagulation factor concentrates presents a significant challenge in both respects, quite independent of any consideration of assessment of the effectiveness of the viral inactivation step. These interactions are illustrated by some of the problems encountered with terminal dry heat-treatment (72 h. at 80 degrees C) of factor VIII and prothrombin complex concentrates manufactured by the Blood Products Laboratory.

Development of solar concentrators for high-power solar-pumped lasers.

Science.gov (United States)

Dinh, T H; Ohkubo, T; Yabe, T

2014-04-20

We have developed unique solar concentrators for solar-pumped solid-state lasers to improve both efficiency and laser output power. Natural sunlight is collected by a primary concentrator which is a 2  m×2  m Fresnel lens, and confined by a cone-shaped hybrid concentrator. Such solar power is coupled to a laser rod by a cylinder with coolant surrounding it that is called a liquid light-guide lens (LLGL). Performance of the cylindrical LLGL has been characterized analytically and experimentally. Since a 14 mm diameter LLGL generates efficient and uniform pumping along a Nd:YAG rod that is 6 mm in diameter and 100 mm in length, 120 W cw laser output is achieved with beam quality factor M2 of 137 and overall slope efficiency of 4.3%. The collection efficiency is 30.0  W/m2, which is 1.5 times larger than the previous record. The overall conversion efficiency is more than 3.2%, which can be comparable to a commercial lamp-pumped solid-state laser. The concept of the light-guide lens can be applied for concentrator photovoltaics or other solar energy optics.

Continued Development of a Soft Gamma-Ray Concentrator

Science.gov (United States)

Bloser, Peter

We propose to continue our development of a concept for a soft gamma-ray (E > 100 keV) concentrator using thin-film multilayer structures. Alternating layers of low- and high-density materials will channel soft gamma-ray photons via total external reflection. A suitable arrangement of bent structures will then concentrate the incident radiation to a point. Gamma-ray optics made in this way offer the potential for soft gamma-ray telescopes with focal lengths of less than 10 m, removing the need for formation flying spacecraft and opening the field up to balloon-borne instruments. Under previous APRA funding we have been investigating methods for efficiently producing such multilayer structures and modeling their performance. We now propose to pursue magnetron sputtering (MS) techniques to quickly produce structures with the required smoothness and thickness, to measure their channeling efficiency and compare with calculations, and to design a "lens" with optimized bandpass and throughput and predict its scientific performance. If successful, this work will confirm that this innovative optics concept is suitable for a balloon-born soft gamma-ray telescope with unprecedented sensitivity.

Development of mixed microbial granular biofilms for denitrification of concentrated wastes

International Nuclear Information System (INIS)

Krishna Mohan, T.V.; Nancharaiah, Y.V.; Venugopalan, V.P.; Narasimhan, S.V.; Satyasai, P.M.

2010-01-01

Nitrate containing wastes are generated at various stages of the nuclear fuel cycle; fuel fabrication and reprocessing. A treatment process for removing nitrate from such concentrated nitrate bearing effluents is needed. Among other available options, biological denitrification is an economical and technically feasible method for nitrate removal. Granular biofilm based sequencing batch reactors (SBRs) may allow designing a compact and high rate processes suitable for the treatment of concentrated effluents. Hence, experiments were carried out in laboratory scale sequencing batch reactors (SBRs) to develop granular biofilms (composed of mixed microbes) for removing nitrate from the concentrated nitrate containing-media. Microbial granular biofilms, capable of consuming nitrate up to 2710 mg/l nitrate-N, were developed under anaerobic conditions in a 6-litre volume sequencing batch reactor (SBR). The SBR was inoculated with activated sludge flocs and operated with 24-h cycle and 50% volumetric exchange ratio. Synthetic media containing acetate as the energy source and electron donor, at carbon to nitrogen molar ratio of 2:1 and 3:1 was fed into the SBRs. Nitrate-N concentration in the SBR was increased in a step-wise manner starting from 677 to 2710 mg/l (1355 to 5420 mg/l in the feed). Complete removal of influent nitrate occurred within the first few hours of SBR cycle period. Effluent nitrate and nitrite levels (∼3 mg/l nitrate-N or nitrite-N) at the end of SBR cycle period (24 h) were found to be below the discharge limits. Under these conditions biomass predominantly consisted of granular biofilms. Results show the potential of granular biofilm based SBR for converting nitrate to nitrogen gas from concentrated nitrate bearing industrial effluents. (author)

Kinetic model for predicting the concentrations of active halogens species in chlorinated saline cooling waters. Final report

International Nuclear Information System (INIS)

Haag, W.R.; Lietzke, M.H.

1981-08-01

A kinetic model has been developed for describing the speciation of chlorine-produced oxidants in seawater as a function of time. The model is applicable under a broad variety of conditions, including all pH range, salinities, temperatures, ammonia concentrations, organic amine concentrations, and chlorine doses likely to be encountered during power plant cooling water chlorination. However, the effects of sunlight are not considered. The model can also be applied to freshwater and recirculating water systems with cooling towers. The results of the model agree with expectation, however, complete verification is not feasible at the present because analytical methods for some of the predicted species are lacking

Kinetic model for predicting the concentrations of active halogens species in chlorinated saline cooling waters. Final report

Energy Technology Data Exchange (ETDEWEB)

Haag, W.R.; Lietzke, M.H.

1981-08-01

A kinetic model has been developed for describing the speciation of chlorine-produced oxidants in seawater as a function of time. The model is applicable under a broad variety of conditions, including all pH range, salinities, temperatures, ammonia concentrations, organic amine concentrations, and chlorine doses likely to be encountered during power plant cooling water chlorination. However, the effects of sunlight are not considered. The model can also be applied to freshwater and recirculating water systems with cooling towers. The results of the model agree with expectation, however, complete verification is not feasible at the present because analytical methods for some of the predicted species are lacking.

INAA of Zn and impurity elements in Zn ores and concentrates

International Nuclear Information System (INIS)

Op de Beeck, J.; De Norre, L.; Hoste, J.

1985-01-01

The present work concerns the analysis of zinc ores and concentrates. In the first place a procedure for the routine determination of fluorine in Zinc sulfide ores has been developed, based on activation with the fast neutrons of the isotope source. In the second place a procedure for the routine determination of Cadmium in Zinc ores has been developed and finally the routine determination of Zinc itself is at present being completed

Microgrid Design, Development and Demonstration - Final Report for Phase I and Phase II

Energy Technology Data Exchange (ETDEWEB)

Bose, Sumit [GE Global Research Center, Niskayuna, NY (United States); Krok, Michael [GE Global Research Center, Niskayuna, NY (United States)

2011-02-08

This document constitutes GE’s final report for the Microgrid Design, Development and Demonstration program for DOE’s Office of Electricity Delivery and Energy Reliability, Award DE-FC02-05CH11349. It contains the final report for Phase I in Appendix I, and the results the work performed in Phase II. The program goal was to develop and demonstrate a Microgrid Energy Management (MEM) framework for a broad set of Microgrid applications that provides unified controls, protection, and energy management. This project contributed to the achievement of the U.S. Department of Energy’s Renewable and Distributed Systems Integration Program goals by developing a fully automated power delivery microgrid network that: - Reduces carbon emissions and emissions of other air pollutants through increased use of optimally dispatched renewable energy, - Increases asset use through integration of distributed systems, - Enhances reliability, security, and resiliency from microgrid applications in critical infrastructure protection, constrained areas of the electric grid, etc. - Improves system efficiency with on-site, distributed generation and improved economic efficiency through demand-side management.

Phosphorus Export Model Development in a Terminal Lake Basin using Concentration-Streamflow Relationship

Science.gov (United States)

Jeannotte, T.; Mahmood, T. H.; Matheney, R.; Hou, X.

2017-12-01

Nutrient export to streams and lakes by anthropogenic activities can lead to eutrophication and degradation of surface water quality. In Devils Lake, ND, the only terminal lake in the Northern Great Plains, the algae boom is of great concern due to the recent increase in streamflow and consequent rise in phosphorus (P) export from prairie agricultural fields. However, to date, very few studies explored the concentration (c) -streamflow (q) relationship in the headwater catchments of the Devils Lake basin. A robust watershed-scale quantitative framework would aid understanding of the c-q relationship, simulating P concentration and load. In this study, we utilize c-q relationships to develop a simple model to estimate phosphorus concentration and export from two headwater catchments of different size (Mauvais Coulee: 1032 km2 and Trib 3: 160 km2) draining to Devils Lake. Our goal is to link the phosphorus export model with a physically based hydrologic model to identify major drivers of phosphorus export. USGS provided the streamflow measurements, and we collected water samples (filtered and unfiltered) three times daily during the spring snowmelt season (March 31, 2017- April 12, 2017) at the outlets of both headwater catchments. Our results indicate that most P is dissolved and very little is particulate, suggesting little export of fine-grained sediment from agricultural fields. Our preliminary analyses in the Mauvais Coulee catchment show a chemostatic c-q relationship in the rising limb of the hydrograph, while the recession limb shows a linear and positive c-q relationship. The poor correlation in the rising limb of the hydrograph suggests intense flushing of P by spring snowmelt runoff. Flushing then continues in the recession limb of the hydrograph, but at a more constant rate. The estimated total P load for the Mauvais Coulee basin is 193 kg/km2, consistent with other catchments of similar size across the Red River of the North basin to the east. We expect

Elevated platelet-derived growth factor-BB concentrations in premature neonates who develop chronic lung disease

Directory of Open Access Journals (Sweden)

Adcock Kim G

2004-06-01

Full Text Available Abstract Background Chronic lung disease (CLD in the preterm newborn is associated with inflammation and fibrosis. Platelet-derived growth factor-BB (PDGF-BB, a potent chemotactic growth factor, may mediate the fibrotic component of CLD. The objectives of this study were to determine if tracheal aspirate (TA concentrations of PDGF-BB increase the first 2 weeks of life in premature neonates undergoing mechanical ventilation for respiratory distress syndrome (RDS, its relationship to the development of CLD, pulmonary hemorrhage (PH and its relationship to airway colonization with Ureaplasma urealyticum (Uu. Methods Infants with a birth weight less than 1500 grams who required mechanical ventilation for RDS were enrolled into this study with parental consent. Tracheal aspirates were collected daily during clinically indicated suctioning. Uu cultures were performed on TA collected in the first week of life. TA supernatants were assayed for PDGF-BB and secretory component of IgA concentrations using ELISA techniques. Results Fifty premature neonates were enrolled into the study. Twenty-eight infants were oxygen dependent at 28 days of life and 16 infants were oxygen dependent at 36 weeks postconceptual age. PDGF-BB concentrations peaked between 4 and 6 days of life. Maximum PDGF-BB concentrations were significantly higher in infants who developed CLD or died from respiratory failure. PH was associated with increased risk of CLD and was associated with higher PDGF-BB concentrations. There was no correlation between maximum PDGF-BB concentrations and Uu isolation from the airway. Conclusions PDGF-BB concentrations increase in TAs of infants who undergo mechanical ventilation for RDS during the first 2 weeks of life and maximal concentrations are greater in those infants who subsequently develop CLD. Elevation in lung PDGF-BB may play a role in the development of CLD.

Development of compound parabolic concentrators for solar energy

Energy Technology Data Exchange (ETDEWEB)

O' Gallagher, J.; Winston, R.

1983-10-01

The compound parabolic concentrator (CPC) is not a specific collector, but a family of collectors based on a general design principle for maximizing the geometric concentration, C, for radiation within a given acceptance half angle = thetac. This maximum limit exceeds by a factor of 2 to 4 that attainable by systems using focussing optics. The wide acceptance angles permitted using these techniques have several unique advantages for solar concentrators including the elimination of the diurnal tracking requirement at intermediate concentrations (up to about 10x), collection of circumsolar and some diffuse radiation and relaxed tolerances. Because of these advantages, CPC type concentrators have applications in solar energy wherever concentration is desired, e.g., for a wide variety of both thermal and photovoltaic uses. The basic principles of nonimaging optical design are reviewed. Selected configurations for both non-evacuated and evacuated thermal collector applications are discussed with particular emphasis on the most recent advances. The use of CPC type elements as secondary concentrators is illustrated in the context of higher concentration photovoltaic applications.

Development of Fresnel-based Concentrated Photovoltaic (CPV System with Uniform Irradiance

Directory of Open Access Journals (Sweden)

Irfan Ullah

2014-12-01

Full Text Available Different designs have been presented to achieve high concentration and uniformity for the concentrated photovoltaic (CPV system. Most of the designs have issues of low efficiency in terms of irradiance uniformity. To this end, we present a design methodology to increase irradiance uniformity over solar cell. The system consists of an eight-fold Fresnel lens as a primary optical element (POE and an optical lens, which consists of eight parts, as a secondary optical element (SOE. Sunlight is focused through the POE and then light is spread over cell through the SOE. In the design, maximum sunlight is passed over cell by minimizing losses. Results have shown that the proposed CPV design gives good irradiance uniformity. The concentration module based on this novel design is a promising option for the development of a cost-effective photovoltaic solar energy generation.

Development of Final Running Test System for Digital Systems

Energy Technology Data Exchange (ETDEWEB)

Lee, Kwang-Dae; Lee, Eui-Jong; Lim, Hee-Taek; Kim, Min-Seok [KHNP Central Research Institute, Daejeon (Korea, Republic of)

2016-10-15

In nuclear industry, the newly designed systems to upgrade are qualified to meet IEEE standards and the regulatory guidelines for their functions, performance and reliability requirements. Failure Mode and Effect Analysis, Fault Tree Analysis, and Hazard Analysis have been used to improve the reliability of the control system. To ensure the completeness of the software, the verification and validation processes are carried out during the development process. In spite of the many efforts depending on the analysis and procedures, there are limitations to improve the reliability. The lessons learned from the currently installed system failures show the incompleteness of the final integration test. The current point-to-point and logic-to-logic separate test procedures manually performed by the engineers can cause some procedures missed and have effects on the critical functions. The design processes of the digital systems are met in accordance with the international standards and regulatory guidelines. The lessons learned from the failures of the running digital systems showed the limitations of the current verification and validation efforts. The various improvements and attempts have been considered including the expert review processes and the completeness of the test. In this paper, the Final Running Test Method evaluating the completeness of the digital system using the control patterns and the Test System Architecture are proposed.

Development of Final Running Test System for Digital Systems

International Nuclear Information System (INIS)

Lee, Kwang-Dae; Lee, Eui-Jong; Lim, Hee-Taek; Kim, Min-Seok

2016-01-01

In nuclear industry, the newly designed systems to upgrade are qualified to meet IEEE standards and the regulatory guidelines for their functions, performance and reliability requirements. Failure Mode and Effect Analysis, Fault Tree Analysis, and Hazard Analysis have been used to improve the reliability of the control system. To ensure the completeness of the software, the verification and validation processes are carried out during the development process. In spite of the many efforts depending on the analysis and procedures, there are limitations to improve the reliability. The lessons learned from the currently installed system failures show the incompleteness of the final integration test. The current point-to-point and logic-to-logic separate test procedures manually performed by the engineers can cause some procedures missed and have effects on the critical functions. The design processes of the digital systems are met in accordance with the international standards and regulatory guidelines. The lessons learned from the failures of the running digital systems showed the limitations of the current verification and validation efforts. The various improvements and attempts have been considered including the expert review processes and the completeness of the test. In this paper, the Final Running Test Method evaluating the completeness of the digital system using the control patterns and the Test System Architecture are proposed

Formulation of the fundamental basis for the evaluation of the comparability of different measuring method for the determination of ground air radon concentration. Vol. 1. Final report; Erarbeitung fachlicher Grundlagen zur Beurteilung der Vergleichbarkeit unterschiedlicher Messmethoden zur Bestimmung der Radonbodenluftkonzentration. Bd. 1. Abschlussbericht

Energy Technology Data Exchange (ETDEWEB)

Kemski, J.; Klingel, R.; Siehl, A.; Neznal, M.; Matolin, M.

2012-03-15

The final report on report on ground air radon measurements includes the following chapters: Scope of the research program; Concept of the research project; Development of a passive method for ground air measurement; Sampling and measuring methods; Measured areas; Field measurements; results of geophysical investigations: Castle Lede, Messdorfer Field; Lounovice; Procedural method; Results of ground air radon concentration measurements, meteorological and geophysical parameters; Evaluation, discussion and conclusions.

Development and evaluation of a regression-based model to predict cesium-137 concentration ratios for saltwater fish

International Nuclear Information System (INIS)

Pinder, John E.; Rowan, David J.; Smith, Jim T.

2016-01-01

Data from published studies and World Wide Web sources were combined to develop a regression model to predict "1"3"7Cs concentration ratios for saltwater fish. Predictions were developed from 1) numeric trophic levels computed primarily from random resampling of known food items and 2) K concentrations in the saltwater for 65 samplings from 41 different species from both the Atlantic and Pacific Oceans. A number of different models were initially developed and evaluated for accuracy which was assessed as the ratios of independently measured concentration ratios to those predicted by the model. In contrast to freshwater systems, were K concentrations are highly variable and are an important factor in affecting fish concentration ratios, the less variable K concentrations in saltwater were relatively unimportant in affecting concentration ratios. As a result, the simplest model, which used only trophic level as a predictor, had comparable accuracies to more complex models that also included K concentrations. A test of model accuracy involving comparisons of 56 published concentration ratios from 51 species of marine fish to those predicted by the model indicated that 52 of the predicted concentration ratios were within a factor of 2 of the observed concentration ratios. - Highlights: • We developed a model to predict concentration ratios (C_r) for saltwater fish. • The model requires only a single input variable to predict C_r. • That variable is a mean numeric trophic level available at (fishbase.org). • The K concentrations in seawater were not an important predictor variable. • The median-to observed ratio for 56 independently measured C_r was 0.83.

User's Manual and Final Report for Hot-SMAC GUI Development

Science.gov (United States)

Yarrington, Phil

2001-01-01

A new software package called Higher Order Theory-Structural/Micro Analysis Code (HOT-SMAC) has been developed as an effective alternative to the finite element approach for Functionally Graded Material (FGM) modeling. HOT-SMAC is a self-contained package including pre- and post-processing through an intuitive graphical user interface, along with the well-established Higher Order Theory for Functionally Graded Materials (HOTFGM) thermomechanical analysis engine. This document represents a Getting Started/User's Manual for HOT-SMAC and a final report for its development. First, the features of the software are presented in a simple step-by-step example where a HOT-SMAC model representing a functionally graded material is created, mechanical and thermal boundary conditions are applied, the model is analyzed and results are reviewed. In a second step-by-step example, a HOT-SMAC model of an actively cooled metallic channel with ceramic thermal barrier coating is built and analyzed. HOT-SMAC results from this model are compared to recently published results (NASA/TM-2001-210702) for two grid densities. Finally, a prototype integration of HOTSMAC with the commercially available HyperSizer(R) structural analysis and sizing software is presented. In this integration, local strain results from HyperSizer's structural analysis are fed to a detailed HOT-SMAC model of the flange-to-facesheet bond region of a stiffened panel. HOT-SMAC is then used to determine the peak shear and peel (normal) stresses between the facesheet and bonded flange of the panel and determine the "free edge" effects.

OZONE CONCENTRATION ATTRIBUTABLE PREMATURE DEATH IN POLAND

Directory of Open Access Journals (Sweden)

Krzysztof Skotak

2010-03-01

Full Text Available Ozone in the lower part of the atmosphere (troposphere, strong photochemical oxidant, is not directly emitted to the atmosphere but formed through a series of complex reactions. Ozone concentrations depends on ozone precursors air contamination (mainly nitrogen dioxide and non-methane volatile organic compounds and meteorological conditions (temperature and solar radiation. The main sectors emitted ozone precursors are road transport, power and heat generation plants, household (heating, industry, and petrol storage and distribution. Ozone and some of its precursors are also transported long distances in the atmosphere and are therefore considered a transboundary problem. As a result, the ozone concentrations are often low in busy urban areas and higher in suburban and rural areas. Nowadays, instead of particulate matter, ozone is one of the most widespread global air pollution problems. In and around urban areas, relatively large gradients of ozone can be observed. Because of its high reactivity in elevated concentrations ozone causes serious health problems and damage to ecosystems, agricultural crops and materials. Main ill-health endpoints as a results of ozone concentrations can be characterised as an effect of pulmonary and cardiovascular system, time morbidity and mortality series, development of atherosclerosis and asthma and finally reduction in life expectancy. The associations with increased daily mortality due to ozone concentrations are confirmed by many researches and epidemiological studies. Estimation of the level selected ill-health endpoints (mortality in total and due to cardiovascular and respiratory causes as a result of the short-term ozone exposure in Poland was the main aim of the project. Final results have been done based on estimation method elaborated by WHO, ozone measurements from National Air Quality Monitoring System and statistical information such as mortality rate and populations. All analysis have been done in

Radiation Hardened Telerobotic Dismantling System Development Final Report CRADA No. TC-1340-96

Energy Technology Data Exchange (ETDEWEB)

Smith, C. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Lightman, A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

2017-09-27

This project was a collaborative effort between the University of California, LLNL and RedZone Robotics, Inc. for the development of radiation-hardened telerobotic dismantling systems for use in applications such as nuclear facility remediation, nuclear accident response, and Chemobyltype remediation. The project supported the design, development, fabrication and testing of a Ukrainian robotic systems. The project was completed on time and within budget. All deliverables were completed. The final project deliverables were consistent with the plans developed in the original project with the exception that the fabricated systems remained in Ukraine.

Development of a model for radon concentration in indoor air

International Nuclear Information System (INIS)

Jelle, Bjørn Petter

2012-01-01

A model is developed for calculation of the radon concentration in indoor air. The model takes into account various important parameters, e.g. radon concentration in ground, radon diffusion resistance of radon barrier, air permeance of ground, air pressure difference between outdoor ground and indoor at ground level, ventilation of the building ground and number of air changes per hour due to ventilation. Characteristic case studies are depicted in selected 2D and 3D graphical plots for easy visualization and interpretation. The radon transport into buildings might be dominated by diffusion, pressure driven flow or a mixture of both depending on the actual values of the various parameters. The results of our work indicate that with realistic or typical values of the parameters, most of the transport of radon from the building ground to the indoor air is due to air leakage driven by pressure differences through the construction. By incorporation of various and realistic values in the radon model, valuable information about the miscellaneous parameters influencing the indoor radon level is gained. Hence, the presented radon model may be utilized as a simple yet versatile and powerful tool for examining which preventive or remedial measures should be carried out to achieve an indoor radon level below the reference level as set by the authorities. - Highlights: ► Model development for calculation of radon concentration in indoor air. ► Radon model accounting for various important parameters. ► Characteristic case studies depicted in 2D and 3D graphical plots. ► May be utilized for examining radon preventive measures.

Commercialization of a high energy neutral beam ion source. Final report

International Nuclear Information System (INIS)

1979-01-01

This final report summarizes the effort and presents the results of a Phase II fabrication effort to build an industrial prototype of the LBL developed high energy neutral beam source. The effort was primarily concentrated on incorporating hard vacuum dielectric seals and a ceramic high voltage accelerator insulator. Several other design changes were incorporated for cost, reliability or life improvements to include: (1) accelerator grid locating dowel pins to aid final alignment, (2) plasma source to accelerator captive fasteners to aid filament replacement during source maintenance, (3) molybdenum cooling tubes on all accelerator grids, (4) additional fasteners in the plasma generator to facilitate hard seals, (5) modified suppressor grid rails and holders to simplify final grid alignment, (6) adjusting screws on exit grid rail holders to simplify final grid alignment, (7) addition of adjusting screws to the grid end pieces to simplify alignment, and (8) addition of accelerator hat shims to allow two different grid positioning locations

Commercialization of a high energy neutral beam ion source. Final report

Energy Technology Data Exchange (ETDEWEB)

1979-12-21

This final report summarizes the effort and presents the results of a Phase II fabrication effort to build an industrial prototype of the LBL developed high energy neutral beam source. The effort was primarily concentrated on incorporating hard vacuum dielectric seals and a ceramic high voltage accelerator insulator. Several other design changes were incorporated for cost, reliability or life improvements to include: (1) accelerator grid locating dowel pins to aid final alignment, (2) plasma source to accelerator captive fasteners to aid filament replacement during source maintenance, (3) molybdenum cooling tubes on all accelerator grids, (4) additional fasteners in the plasma generator to facilitate hard seals, (5) modified suppressor grid rails and holders to simplify final grid alignment, (6) adjusting screws on exit grid rail holders to simplify final grid alignment, (7) addition of adjusting screws to the grid end pieces to simplify alignment, and (8) addition of accelerator hat shims to allow two different grid positioning locations.

THE DEVELOPMENT OF PLANTS FOR THE PRODUCTION OF CONCENTRATED PASTES OF FRUIT AND VEGETABLE RAW MATERIALS

Directory of Open Access Journals (Sweden)

G. O. Magomedov

2015-01-01

Full Text Available Summary. Developed a new system for producing concentrated semi-finished products in the form of pastes for the food industry. Currently, an important task of the food industry is the creation of new products with the aim of improving the structure of the range, saving scarce raw materials, as well as reduce sugar intake; development of product functionality and products with extended shelf life. The use of local non-traditional types of plant materials can contribute to solving existing problems. Fruit and vegetable pastes are a valuable food products which can be used as a semifinished product in the confectionery, bakery, food concentrates industry. Fruit and vegetable purees have a distinct structurally viscous or pseudo-plastic properties and concentration form a very viscous mass. Already in the beginning of the process of concentration, i.e. at a relatively low degree of evaporation that leads to a rapid increase in the viscosity of the concentrate mass and reduce evaporation. With increasing temperature is the burning mass, and also change its color and flavor. Therefore, for the concentration of fruit and vegetable purees, you must use equipment whose design takes into account the possible rheological and thermal problems. The analysis of literary data structures evaporators and studies, we developed a system for producing concentrated pastes of fruit and vegetable raw materials. Developed installation can increase the quality of the finished product due to the intensification of the process of concentration, to reduce material and energy resources, increase productivity.

Development of fast measurements of concentration of NORM U-238 by HPGe

Science.gov (United States)

Cha, Seokki; Kim, Siu; Kim, Geehyun

2017-02-01

Naturally Occureed Radioactive Material (NORM) generated from the origin of earth can be found all around us and even people who are not engaged in the work related to radiation have been exposed to unnecessary radiation. This NORM has a potential risk provided that is concentrated or transformed by artificial activities. Likewise, a development of fast measruement method of NORM is emerging to prevent the radiation exposure of the general public and person engaged in the work related to the type of business related thereto who uses the material in which NORM is concentrated or transfromed. Based on such a background, many of countries have tried to manage NORM and carried out regulatory legislation. To effienctly manage NORM, there is need for developing new measurement to quickly and accurately analyze the nuclide and concentration. In this study, development of the fast and reliable measurement was carried out. In addition to confirming the reliability of the fast measurement, we have obtained results that can suggest the possibility of developing another fast measurement. Therefore, as a follow-up, it is possible to develop another fast analytical measurement afterwards. The results of this study will be very useful for the regulatory system to manage NORM. In this study, a review of two indirect measurement methods of NORM U-238 that has used HPGe on the basis of the equilibrium theory of relationships of mother and daughter nuclide at decay-chain of NORM U-238 has been carried out. For comparative study(in order to know reliabily), direct measurement that makes use of alpha spectrometer with complicated pre-processing process was implemented.

Carbon monoxide and COHb concentration in blood in various circumstances

Energy Technology Data Exchange (ETDEWEB)

Modic, J. [Faculty of Mechanical Engineering, University of Ljubljana, Ljubljana (Slovenia)

2003-07-01

On the basis of known medical experiments we find out the correlation between the concentration of carbon monoxide (CO) in inhaling air and the concentration of carboxihemoglobyne (COHb) in human blood. All internal combustion engines produce exhaust gases containing noxious compounds: carbon monoxide, nitrogen oxides (NO{sub x}), carbon oxides (CxHy) and smoke. In a living room is important the smoke of cigarettes, smoke of furnaces, improper ventilation. In tunnel is most dangerous the carbon monoxide if it exceeds an allowable level. In human blood the carbon monoxide causes increasing the concentration of carboxihemoglobyne and in this case the hypoxia of web. With help of mathematical model the concentrations of some dangerous substances at the end of tunnel were calculated. For this case a differential equation also was developed and it shows the correlation between concentration of carbon monoxide in the air and concentration of carboxihemoglobyne in the blood. The constructed mathematical model shows circumstances in the tunnel (velocity of air moving as effect of induction, concentration of noxious substances and criterial number). Also a corresponding computer program was developed, which makes possible a quick and simple calculation. All the results are proved by experiments. Finally the differential equation was done, which shows a temporal connection between both parameters as a function of tunnel characteristics. (author)

Prenatal concentrations of Perfluoroalkyl substances and early communication development in British girls.

Science.gov (United States)

Jeddy, Zuha; Hartman, Terryl J; Taylor, Ethel V; Poteete, Cayla; Kordas, Katarzyna

2017-06-01

Perfluoroalkyl substances (PFAS), found in many household products and classed as endocrine disrupting chemicals, can be transferred through the placenta and are associated with multiple developmental deficits in offspring. Using data from the Avon Longitudinal Study of Parents and Children (ALSPAC), we investigated the association between intrauterine exposure to PFAS and early communication development in 432 mother-daughter dyads at 15 and 38months of age. Concentrations of perfluorooctane sulfonate (PFOS), perfluorooctanoate (PFOA), perfluorohexane sulfonate (PFHxS), and perfluorononanoate (PFNA) were measured in maternal serum collected during pregnancy. Early communication development was measured with the ALSPAC-adapted MacArthur Communicative Development Inventories for Infants and Toddlers. The infant questionnaire measured verbal comprehension, vocabulary comprehension and production, nonverbal communication, and social development. The toddler questionnaire measured language, intelligibility, and communicative sub-scores. Multivariable linear regression was used to examine associations between each PFAS exposure and each communication sub-scale score. The association between maternal PFAS concentrations and early communication development at 15 and 38months of age varied by maternal age at delivery. In daughters of younger mothers (PFAS was positively and negatively associated with communication development among girls, with inconsistent pattern of association across all measured PFAS and endpoints. Copyright © 2017 Elsevier B.V. All rights reserved.

Cream concentrated latex for foam rubber products

Science.gov (United States)

Suksup, R.; Imkaew, C.; Smitthipong, W.

2017-12-01

Fresh natural latex (around 40% rubber and 60% water) can be transformed to concentrated natural latex (around 60% rubber and 40% water) in order to realise economical transportation and easier latex product’s preparation. The concentrated natural latex is an extremely valuable material. It can be applied for many types of products, for example, foam rubber as pillow and mattress, elastic band, etc. Industrially, the concentrated natural latex can be prepared by centrifugation which requires an enormous expensive machine. From the eco-friendly products point of view, most of rubber entrepreneurs in the world try to develop a green rubber product. So, the main objective of this study is to prepare the cream concentrated latex without any sophisticated machine. Thus, we work on a simple, cheap and green method that does not use any expensive machine but uses water-based chemical as sodium alginate to prepare the cream concentrated latex. The optimal amount of sodium alginate in the latex was studied. The main characteristics of the cream concentrated latex were tested by various technics, such as alkalinity, total solid content (TSC), dry rubber content (DRC), etc. We found that there are no significant differences of results between fresh natural latex and cream concentrated latex, except for the TSC and DRC. The TSC and DRC of cream latex are higher than those of fresh natural latex. Finally, we propose a model of natural rubber particle and sodium alginate to form the cream concentrated latex.

Determination of mercury concentration in biological materials by neutron activation analysis

International Nuclear Information System (INIS)

Munoz, L.; Gras, N.; Cortes, E.; Cassorla, V.

1983-01-01

The objective of this work was to obtain a confident analytical method for measuring the mercury concentration in biological materials. Destructive neutron activation analysis was used for this purpose and a radiochemical separation method was studied to isolate the mercury from its main interferences: sodium and phosphorus, because these elements in biological materials are in high concentrations. The method developed was based on the copper amalgamation under controlled conditions. Yield and reproductibility studies were performed using 203 Hg as radioactive tracer. Finally, food samples of regular consumption were analyzed and the results were compared with those recommended by FAO/WHO. (Author)

Telephone Flat Geothermal Development Project Environmental Impact Statement Environmental Impact Report. Final: Comments and Responses to Comments

Energy Technology Data Exchange (ETDEWEB)

None

1999-02-01

This document is the Comments and Responses to Comments volume of the Final Environmental Impact Statement and Environmental Impact Report prepared for the proposed Telephone Flat Geothermal Development Project (Final EIS/EIR). This volume of the Final EIS/EIR provides copies of the written comments received on the Draft EIS/EIR and the leady agency responses to those comments in conformance with the requirements of the National Environmental Policy Act (NEPA) and the California Environmental Quality Act (CEQA).

Fiber Optic Hydrogen Sensor Development: Cooperative Research and Development Final Report, CRADA number CRD-05-00158

International Nuclear Information System (INIS)

Ringer, M.

2010-01-01

NREL and Nuclear Filter Technology collaborated to develop a prototype product for a hydrogen threshold sensor that was used to monitor hydrogen production in the transport of nuclear waste transport containers. This application is a core business area for Nuclear Filter Technology and will provide a basis for creating sensor products that are used in other licensed fields of use. Activities included design and construction of prototype product, product testing and debugging, and finalizing a prototype for initial field tests.

Chromatographic decontamination of medium-activity waste concentrates

International Nuclear Information System (INIS)

Faubel, W.; Menzler, P.M.; Sameh, A.A.

1988-01-01

The chromatographic decontamination of a MAW concentrate was carried out in a laboratory plant in 1-l-batches in the following way: In order to purify the nitric MAW concentrate from its solid and organic contamination products, it is passed through a filter and an absorber (SM7) for organic species. Subsequently the purified solution runs on-line through all following columns. First the main activity carrier cesium ( 137 Cs, 134 Cs) is transferred to ammonium molybdate phosphate (AMP-1) by means of a newly developed fluidized bed process. In the further course, 125 Sb is separated on metal oxides (Sb 2 O 5 , MnO 2 ) and the three-valued actinides/lanthanides on an extraction-chromatographic CMPO column. Finally the remaining 106 Ru and 60 Co activities are separated on dimethylglyoximes (DMG) coated on active carbon. (orig./RB) [de

The optics of the Final Focus Test Beam

International Nuclear Information System (INIS)

Irwin, J.; Brown, K.; Bulos, F.; Burke, D.; Helm, R.; Roy, G.; Ruth, R.; Yamamoto, N.; Oide, K.

1991-05-01

The Final Focus Test Beam (FFTB), currently under construction at the end of the SLAC Linac, is being built by an international collaboration as a test bed for ideas and methods required in the design and construction of final focus systems for next generation e + e - linear colliders. The FFTB lattice is based on the previously developed principle of using sextupole pairs in a dispersive region to compensate chromaticity. The linear lattice was optimized for length, and implementation of diagnostic procedures. The transformations between sextupole pairs (CCX and CCY) are exactly -I, the matrix for the intermediate transformer (BX) is exactly diagonal, and the dispersion function has zero slope at the sextupoles and is thus zero at the minimum of the β x function in the intermediate transformer. The introduction of sextupoles in final focus systems leads to the presence of additional optical aberrations, and synchrotron radiation in the dipoles also enlarges the final spot size. The important fourth-order optical aberrations which determine the main features of the design have been identified. Additional lower order aberrations arise in the implementation of these designs, since the real system is not the ideal design. We concentrate on these aberrations and describe strategies for their diagnosis and correction

Development of the SEA Corporation Powergrid{trademark} photovoltaic concentrator

Energy Technology Data Exchange (ETDEWEB)

Kaminar, N.; Curchod, D.; Daroczi, S.; Walpert, M.; Sahagian, J.; Pepper, J. [Photovoltaics International, LLC, Sunnyvale, CA (United States)

1998-03-01

This report covers the three phase effort to bring the SEA Corporation`s Powergrid{trademark} from the concept stage to pilot production. The three phases of this contract covered component development, prototype module development, and pilot line production. The Powergrid is a photovoltaic concentrator that generates direct current electricity directly from sunlight using a linear Fresnel lens. Analysis has shown that the Powergrid has the potential to be very low cost in volume production. Before the start of the project, only proof of concept demonstrations of the components had been completed. During the project, SEA Corporation developed a low cost extruded Fresnel lens, a low cost receiver assembly using one sun type cells, a low cost plastic module housing, a single axis tracking system and frame structure, and pilot production equipment and techniques. In addition, an 800 kW/yr pilot production rate was demonstrated and two 40 kW systems were manufactured and installed.

Ripeness sensor development. Final report of a Phase 2 study

Energy Technology Data Exchange (ETDEWEB)

Stroshine, R.

1995-08-01

This is a final report for the Phase II study entitled ``Ripeness Sensor Development.`` The overall objective of the study was the development of a prototype device capable of testing whole fruits for sugar content. Although ripeness and sugar content are not synonymous, they are closely related. Furthermore, the consumer`s acceptance of or preference for fruits is strongly influenced by sugar content. Therefore, the device was called a ripeness sensor. The principle behind the measurement is proton magnetic resonance ({sup 1}H-MR). For several decades, chemists, pharmacists and other scientists have been using {sup 1}H-MR to investigate chemical structure and composition. More recently, the technique has been used in laboratories of the food industry for quality control. This effort represents one of the first attempts to adapt {sup 1}H-MR to use in a commercial facility. 28 refs., 36 figs., 7 tabs.

Developing Derrida’s Psychoanalytic Graphology: Diametric and Concentric Spatial Movements

OpenAIRE

Downes, Paul

2013-01-01

Derrida’s work encompasses dynamic spatial dimensions to understanding as a pervasive theme, including the search for a ‘new psychoanalytic graphology’ in Writing and Difference. This preoccupation with a spatial text for repression also occurs later in Archive Fever. Building on Derrida, this paper seeks to develop key aspects of a new dynamic psychoanalytic graphology through diametric and concentric interactive spatial relation. These spatial movements emerge from a radical reconstruction ...

Relationship Between Iodine Concentration in Maternal Colostrum and Neurobehavioral Development of Infants in Shanghai, China.

Science.gov (United States)

Wu, Meiqin; Wu, Deqing; Wu, Wei; Li, Hui; Cao, Lulu; Xu, Jian; Yu, Xiaodan; Bian, Xiaoyan; Yan, Chonghuai; Wang, Weiye

2016-08-01

It is well known that iodine plays an important role in the process of early growth and development of most organs, especially the brain. However, iodine concentration in the colostrum and its association with the neurobehavioral development of infants remains unclear. Colostrums from 150 women were collected, and their iodine concentrations were measured. The median colostrum iodine level was 187.8 μg/L. The Bayley Scales of Infant and Toddler Development-III test was performed when the infants were about 18 months. The mean cognitive, language, and motor composite scores were 105.3 ± 9.8, 105.2 ± 11.1, and 104.6 ± 6.7, respectively. And the mean scores of the 5 subtests were 11.1 ± 2.0, 9.3 ± 2.0, 12.4 ± 2.3, 11.1 ± 1.2, and 10.4 ± 1.2, respectively. No statistically significant difference was observed in the cognition, language, or motor development of infants across different levels of colostrum iodine. After adjusting for a range of confounding factors, colostrum iodine concentration was a predictor of motor development, specifically gross motor development. © The Author(s) 2016.

Mathematic model of regional economy development by the final result of labor resources

Science.gov (United States)

Zaitseva, Irina; Malafeev, Oleg; Strekopytov, Sergei; Bondarenko, Galina; Lovyannikov, Denis

2018-04-01

This article presents the mathematic model of regional economy development based on the result of labor resources. The solution of a region development-planning problem is considered for the period of long-lasting planning taking into account the beginning and the end of the planned period. The challenge is to find the distribution of investments in the main and additional branches of the regional economy, which will provide simultaneous transaction of all major sectors of the regional economy from the given condition to the predetermined final state.

Final Project Report for Award ER65581

Energy Technology Data Exchange (ETDEWEB)

Stoy, Paul C. [Montana State Univ., Bozeman, MT (United States)

2017-07-13

The attached final project report describes contributions of Montana State University (MSU) to the project "Bridging land-surface fluxes and aerosol concentrations to triggering convective rainfall" (PI: Fuentes).

Monitoring and modeling wetland chloride concentrations in relationship to oil and gas development

Science.gov (United States)

Post van der Burg, Max; Tangen, Brian A.

2015-01-01

Extraction of oil and gas via unconventional methods is becoming an important aspect of energy production worldwide. Studying the effects of this development in countries where these technologies are being widely used may provide other countries, where development may be proposed, with some insight in terms of concerns associated with development. A fairly recent expansion of unconventional oil and gas development in North America provides such an opportunity. Rapid increases in energy development in North America have caught the attention of managers and scientists as a potential stressor for wildlife and their habitats. Of particular concern in the Northern Great Plains of the U.S. is the potential for chloride-rich produced water associated with unconventional oil and gas development to alter the water chemistry of wetlands. We describe a landscape scale modeling approach designed to examine the relationship between potential chloride contamination in wetlands and patterns of oil and gas development. We used a spatial Bayesian hierarchical modeling approach to assess multiple models explaining chloride concentrations in wetlands. These models included effects related to oil and gas wells (e.g. age of wells, number of wells) and surficial geology (e.g. glacial till, outwash). We found that the model containing the number of wells and the surficial geology surrounding a wetland best explained variation in chloride concentrations. Our spatial predictions showed regions of localized high chloride concentrations. Given the spatiotemporal variability of regional wetland water chemistry, we do not regard our results as predictions of contamination, but rather as a way to identify locations that may require more intensive sampling or further investigation. We suggest that an approach like the one outlined here could easily be extended to more of an adaptive monitoring approach to answer questions about chloride contamination risk that are of interest to managers.

Development of safety-relevant components for the transport and handling of final storage casks for waste from decommissioning

International Nuclear Information System (INIS)

Bruening, D.; Geiser, H.; Kloeckner, F.; Rittscher, D.; Schlesinger, H.J.

1992-10-01

The aim of the study was the development, construction and testing of a transportation system that is able to transport cylindrical waste containers as well as containers from the deliverer to the 'KONRAD' final repository. A transport palette has been developed that can carry two cylindrical waste containers with type B requirement or classification II. An Open-All-Container for the transport of palettes and 'KONRAD' containers has been developed. A storage of cylindrical waste containers and containers in the final repository is possible with the newly developed transportation system. Safety specifications of the transportation system have been passed successfully. (orig.). 30 refs., 8 tabs., 74 figs [de

Automatic data acquisition and on-line analysis of trace element concentration in serum samples

International Nuclear Information System (INIS)

Lecomte, R.; Paradis, P.; Monaro, S.

1978-01-01

A completely automated system has been developed to determine the trace element concentration in biological samples by measuring charged particle induced X-rays. A CDC-3100 computer with ADC and CAMAC interface is employed to control the data collection apparatus, acquire data and perform simultaneously the analysis. The experimental set-up consists of a large square plexiglass chamber in which a commercially available 750H Kodak Carousel is suitably arranged as a computer controlled sample changer. A method of extracting trace element concentrations using reference spectra is presented and an on-line program has been developed to easily and conveniently obtain final results at the end of each run. (Auth.)

Mission related to regulation and development of the photovoltaic sector in France. Final report

International Nuclear Information System (INIS)

Charpin, J.M; Sine, A.; Helleisen, Ph.; Tlili, C.; Trink, C.; Stoffaes, Ch.

2010-01-01

This report first gives an overview of the development of the photovoltaic stock in France (high potential with a middle term development constrained by high costs, consequences of a very strong increase of demands at the end of 2009, perspective of development at a rather high rate). Then, it outlines and discusses the financial consequences of such a high rate development, and the inadequacy between industrial objectives and development rate. It presents a development plan for this sector, stresses the need to implement new purchase obligation measures before the summer 2010, and to define a global action plan to be implemented at the beginning of 2011 for the development of photovoltaic electricity. Elements of international comparison are finally proposed

Investigation of freeze concentration as a process for industrial energy conservation in black liquor, acetic acid, and citrus juice applications. Final report

Energy Technology Data Exchange (ETDEWEB)

None

1979-07-01

One of the largest consumers of energy in industrial processing is the equipment that concentrates weak aqueous solutions to stronger more sellable or reusable concentrations. The technical and economic feasibility of applying freeze concentration (that is, crystallization and removal from solution of pure solvent - water) as an alternative to heat evaporation (or distillation) to three industrial applications is established. For each of the applications - pulp mill black liquor concentration, acetic acid recovery and orange juice concentration - the economic analyses indicate that the energy savings achievable by freezing justify the respective capital investments with pay out periods of generally one to three years. Past freeze concentration operations have been in the 10,000 to 100,000 gallons per day range for sea water desalination. Research and development work will be required to adapt this work to the three industrial applications.

Development of mediator-type biosensor to wirelessly monitor whole cholesterol concentration in fish.

Science.gov (United States)

Takase, Mai; Murata, Masataka; Hibi, Kyoko; Huifeng, Ren; Endo, Hideaki

2014-04-01

We developed a wireless monitoring system to monitor fish condition by tracking the change in whole cholesterol concentration. The whole cholesterol concentration of fish is a source of steroid hormones or indicator of immunity level, which makes its detection important for tracking physiological condition of fish. Wireless monitoring system comprises of mediator-type biosensor and wireless transmission device. Biosensor is implantable to fish body, and transmission device is so light, in that fish is allowed to swim freely during monitoring. Cholesterol esterase and oxidase were fixated on to the detection site of biosensor and used to detect the whole cholesterol concentration. However, cholesterol oxidase incorporates oxidation-reduction reaction of oxygen for detection, which concentration fluctuates easily due to change in environmental condition. Meanwhile, mediator-type biosensor enables monitoring of whole cholesterol concentration by using mediator to substitute that oxidation-reduction reaction of oxygen. Characteristic of fabricated mediator-type biosensor was tested. The sensor output current of mediator-type biosensor remained stable compared to output current of non-mediator-type biosensor under fluctuating oxygen concentration of 0-8 ppm, which implied that this sensor is less affected by change in dissolved oxygen concentration. That biosensor was then implanted into fish for wireless monitoring. As a result, approximately 48 h of real-time monitoring was successful.

Final report of evaluation of dose and measurement of radon concentration

International Nuclear Information System (INIS)

1998-03-01

A mean annual exposure to radon daughters in indoor air was estimated on the basis of measurement of radon concentration in indoor air in Japan from fiscal 1992 to 1996. Doses were estimated by UNSCEAR method. The representative values in this report show the mean values in whole Japan. Each dose in the local area was different reflecting the different concentration of radon daughters. However, the same parameters were used in each area. When mean annual dose of radon daughters was estimated, we used 15.5 Bq m -3 mean annual exposure to radon daughters in indoor air, 5 Bq m -3 that in outdoor air, 0.4 the equilibrium factor indoor, 0.6 the equilibrium factor outdoor and 0.9 of P. The model of UNSCEAR based on these above values gave 0.46 mSv y -1 mean annual dose of radon daughters which were consisted of from 0.38 mSv y -1 in Kanto district to 0.52 mSv y -1 Kyushu, Okinawa district. (S.Y.)

Final report of evaluation of dose and measurement of radon concentration

Energy Technology Data Exchange (ETDEWEB)

NONE

1998-03-01

A mean annual exposure to radon daughters in indoor air was estimated on the basis of measurement of radon concentration in indoor air in Japan from fiscal 1992 to 1996. Doses were estimated by UNSCEAR method. The representative values in this report show the mean values in whole Japan. Each dose in the local area was different reflecting the different concentration of radon daughters. However, the same parameters were used in each area. When mean annual dose of radon daughters was estimated, we used 15.5 Bq m{sup -3} mean annual exposure to radon daughters in indoor air, 5 Bq m{sup -3} that in outdoor air, 0.4 the equilibrium factor indoor, 0.6 the equilibrium factor outdoor and 0.9 of P. The model of UNSCEAR based on these above values gave 0.46 mSv y{sup -1} mean annual dose of radon daughters which were consisted of from 0.38 mSv y{sup -1} in Kanto district to 0.52 mSv y{sup -1} Kyushu, Okinawa district. (S.Y.)

Characterization of a photovoltaic-thermal module for Fresnel linear concentrator

International Nuclear Information System (INIS)

Chemisana, D.; Ibanez, M.; Rosell, J.I.

2011-01-01

Highlights: → A combined domed Fresnel lens - CPC PVT system is designed and characterized. → Electrical and thermal experiments have been performed. → CFD analysis has been used to determine thermal characteristic dimensionless numbers. - Abstract: An advanced solar unit is designed to match the needs of building integration and concentrating photovoltaic/thermal generation. The unit proposed accurately combines three elements: a domed linear Fresnel lens as primary concentrator, a compound parabolic reflector as secondary concentrator and a photovoltaic-thermal module. In this work the photovoltaic-thermal generator is built, analysed and characterized. Models for the electrical and thermal behaviour of the module are developed and validated experimentally. Applying a thermal resistances approach the results from both models are combined. Finally, efficiency electrical and thermal curves are derived from theoretical analysis showing good agreement with experimental measurements.

Development of new waste form for treatment and disposal of concentrated liquid radioactive waste

International Nuclear Information System (INIS)

Kwak, Kyung Kil; Ji, Young Yong

2010-12-01

The radioactive waste form should be meet the waste acceptance criteria of national regulation and disposal site specification. We carried out a characterization of rad waste form, especially the characteristics of radioactivity, mechanical and physical-chemical properties in various rad waste forms. But asphalt products is not acceptable waste form at disposal site. Thus we are change the product materials. We select the development of the new process or new materials. The asphalt process is treatment of concentrated liquid and spent-resin and that we decide the Development of new waste form for treatment and disposal of concentrated liquid radioactive waste

Exergy, Energy, and Dynamic Parameter Analysis of Indigenously Developed Low-Concentration Photovoltaic System

OpenAIRE

Pankaj Yadav; Brijesh Tripathi; Manoj Kumar

2013-01-01

Piecewise linear parabolic trough collector (PLPTC) is designed and developed to concentrate solar radiation on monocrystalline silicon based photovoltaic module. A theoretical model is used to perform electrical energy and exergy analysis of low-concentration photovoltaic (LCPV) system working under actual test conditions (ATC). The exergy efficiency of LCPV system is in the range from 5.1% to 4.82% with increasing rate of input exergy rate from 30.81 W to 96.12 W, when conce...

Recent developments in luminescent solar concentrators

Science.gov (United States)

van Sark, W. G. J. H. M.

2014-10-01

High efficiency photovoltaic devices combine full solar spectrum absorption and effective generation and collection of charge carriers, while commercial success depends on cost effectiveness in manufacturing. Spectrum modification using down shifting has been demonstrated in luminescent solar concentrators (LSCs) since the 1970s, as a cheap alternative for standard c-Si technology. LSCs consist of a highly transparent plastic plate, in which luminescent species are dispersed, which absorb incident light and emit light at a red-shifted wavelength, with high quantum efficiency. Material issues have hampered efficiency improvements, in particular re-absorption of light emitted by luminescent species and stability of these species. In this contribution, approaches are reviewed on minimizing re-absorption, which should allow surpassing the 10% luminescent solar concentrator efficiency barrier.

DEVELOPMENT OF ATTENTION CONCENTRATION AND STABILITY OF RAILWAY STUDENTS IN THE PROCESS OF PSYCHOLOGICAL AND PSYCHOPHYSICAL TRAINING

Directory of Open Access Journals (Sweden)

V. V. Pichurin

2014-03-01

Full Text Available Purpose. Some railway professions impose exceptionally high demands on such characteristics of railway students as concentration and stability. One should find out the conditions for effective development of these characteristics in the process of physical training. Methodology. Pedagogical experiment is the main method of research. During this experiment the content of psychological and psychophysical training foundations developed by the author was an independent value. A dependent value was the dynamics performance of the level of development of concentration and stability of railway students’ attention. Findings. It was established, that realization of measure complex (included by the author to the content of foundations of psychological and psychophysical training of railway students during the lessons is the effective direction of the development of the attention concentration and stability. Originality. The effectiveness of using the psychological and psychophysical training of students for development of attention concentration and stability during the lessons was confirmed. Practical value. Realization of the proposed approach during the training of specialists for the railway branch will increase the productivity and safety of railway transportations.

Concentrating photovoltaics for the Tropics. Final Report, June 1, 1978-February 28, 1979

Energy Technology Data Exchange (ETDEWEB)

1979-06-30

The design and specification of a photovoltaic concentrator total energy system are presented. The design will provide nearly half the electrical energy needs and most of the thermal energy needs (absorption chillers) of the Center for Energy and Environment Research, University of Puerto Rico, and the hot water needs of the Oncologic Hospital and Children's Hospital, Puerto Rico Medical Center. The system will utilize 34,190 sq ft of 40X slat type concentrators with secondary CPC concentrators to provide 162 kWe. The combined photovoltaic/thermal collector system utilizes a 20,000 gal steel thermal storage tank, and two absorption refrigeration units which will produce a total of 149 tons of cooling. Detailed drawings and system fabrication and installation plans are included. Insolation data for the San Juan, Puerto Rico site are presented, and calculated system performance based on this data is presented. (WHK)

Concentrating photovoltaics for the Tropics. Final Report, June 1, 1978-February 28, 1979

Energy Technology Data Exchange (ETDEWEB)

1979-06-30

The design and specification of a photovoltaic concentrator total energy system are presented. The design will provide nearly half the electrical energy needs and most of the thermal energy needs (absorption chillers) of the Center for Energy and Environment Research, University of Puerto Rico, and the hot water needs of the Oncologic Hospital and Children's Hospital, Puerto Rico Medical Center. The system will utilize 34,190 sq ft of 40X slat type concentrators with secondary CPC concentrators to provide 162 kWe. The combined photovoltaic/thermal collector system utilizes a 20,000 gal steel thermal storage tank, and two absorption refrigeration units which will produce a total of 149 tons of cooling. Detailed drawings and system fabrication and installation plans are included. Insolation data for the San Juan, Puerto Rico site are presented, and calculated system performance based on this data is presented. (WHK)

Effects of export concentration on CO2 emissions in developed countries: an empirical analysis.

Science.gov (United States)

Apergis, Nicholas; Can, Muhlis; Gozgor, Giray; Lau, Chi Keung Marco

2018-03-08

This paper provides the evidence on the short- and the long-run effects of the export product concentration on the level of CO 2 emissions in 19 developed (high-income) economies, spanning the period 1962-2010. To this end, the paper makes use of the nonlinear panel unit root and cointegration tests with multiple endogenous structural breaks. It also considers the mean group estimations, the autoregressive distributed lag model, and the panel quantile regression estimations. The findings illustrate that the environmental Kuznets curve (EKC) hypothesis is valid in the panel dataset of 19 developed economies. In addition, it documents that a higher level of the product concentration of exports leads to lower CO 2 emissions. The results from the panel quantile regressions also indicate that the effect of the export product concentration upon the per capita CO 2 emissions is relatively high at the higher quantiles.

Luminescent solar concentrator

Directory of Open Access Journals (Sweden)

Tugce Tosun

2015-07-01

Full Text Available Luminescent solar concentrator (LSC is a device that has luminescent molecules embedding or topping polymeric or glass waveguide to generate electricity from sunlight with a photovoltaic cell attachment. LSCs can be employed both in small and large scale projects, independent on the direction or angle of the surface with respect to the sun, promising more freedom for integration in urban environments compared to the traditional PV systems. The aim of the SEB&C PDEng project is to investigate the applicability of this innovative technology in the built environment and to bridge the gap of knowledge linking societal, design and technological aspects. The final goal is to exhibit potential application concepts of LSC developed by co-creative methods at SPARK campus which is a hub for open innovation in built environment. Necessity of a paradigm shift towards sustainable and smart cities came into being due to the significant increase in energy demand of the buildings. The challenge is to increase renewable sources in the energy mix while designing aesthetic environments. Thus, building integrated renewable energy technologies represent a great opportunity to help overcome this current challenge. Smart energy, energy efficiency and use of renewable sources are key aspects to be considered nowadays and many innovative technologies need further exploitation to be commercially viable, such as luminescent solar concentrator.

Accurate determination of 41Ca concentrations in spent resins from the nuclear industry by Accelerator Mass Spectrometry

International Nuclear Information System (INIS)

Nottoli, Emmanuelle; Bourlès, Didier; Bienvenu, Philippe; Labet, Alexandre; Arnold, Maurice; Bertaux, Maité

2013-01-01

The radiological characterisation of nuclear waste is essential for managing storage sites. Determining the concentration of Long‐Lived RadioNuclides (LLRN) is fundamental for their long-term management. This paper focuses on the measurement of low 41 Ca concentrations in ions exchange resins used for primary fluid purification in Pressurised Water Reactors (PWR). 41 Ca concentrations were successfully measured by Accelerator Mass Spectrometry (AMS) after the acid digestion of resin samples, followed by radioactive decontamination and isobaric suppression through successive hydroxide, carbonate, nitrate and final CaF 2 precipitations. Measured 41 Ca concentrations ranged from 0.02 to 0.03 ng/g, i.e. from 0.06 to 0.09 Bq/g. The 41 Ca/ 60 Co activity ratios obtained were remarkably reproducible and in good agreement with the current ratio used for resins management. - Highlights: • In the context of radioactive waste management, this study aimed at measuring 41 Ca in spent resins using Accelerator Mass Spectrometry. • A chemical treatment procedure was developed to quantitatively recover calcium in solution and selectively extract it. • Developed firstly on synthetic matrices, the chemical treatment procedure was then successfully applied to real resin samples. • Accelerator mass spectrometry allowed measuring concentrations of 41 Ca in spent resins as low as 0.02 ng/g of dry resin. • Final results are in agreement with current data used for spent resins management

Development of concentration measurement system in a mini-channel using a local NMR sensor

International Nuclear Information System (INIS)

Ogawa, Kuniyasu; Haishi, Tomoyuki

2008-01-01

A local NMR sensor to measure methanol concentration of fluid flowing in a mini-channel was developed. The principle of the methanol sensor is based on the chemical shift of CH and OH species under high magnetic field. The sensor consists of a planar surface coil of 0.60 mm inside diameter. Using the sensors, local methanol concentration of water-methanol mixture in the mini-channel of 3.0 mm width and 1.5 mm depth was measured. The effects of flow velocity in the channel and the gravity direction on the methanol concentration distribution in the channel were investigated experimentally. (author)

Development of a package program for estimating ground level concentrations of radioactive gases

International Nuclear Information System (INIS)

Nilkamhang, W.

1986-01-01

A package program for estimating ground level concentration of radioactive gas from elevate release was develop for use on IBM P C microcomputer. The main program, GAMMA PLUME NT10, is based on the well known VALLEY MODEL which is a Fortran computer code intended for mainframe computers. Other two options were added, namely, calculation of radioactive gas ground level concentration in Ci/m 3 and dose equivalent rate in mren/hr. In addition, a menu program and editor program were developed to render the program easier to use since the option could be readily selected and the input data could be easily modified as required through the keyboard. The accuracy and reliability of the program is almost identical to the mainframe. Ground level concentration of radioactive radon gas due to ore program processing in the nuclear chemistry laboratory of the Department of Nuclear Technology was estimated. In processing radioactive ore at a rate of 2 kg/day, about 35 p Ci/s of radioactive gas was released from a 14 m stack. When meteorological data of Don Muang (average for 5 years 1978-1982) were used maximum ground level concentration and the dose equivalent rate were found to be 0.00094 p Ci/m 3 and 5.0 x 10 -10 mrem/hr respectively. The processing time required for the above problem was about 7 minutes for any case of source on IBM P C which was acceptable for a computer of this class

Particle analysis on concentrated particle suspensions by transmission fluctuation spectrometry with band-pass filters: part 2. Experimental results

International Nuclear Information System (INIS)

Xu, Yamin; Shen, Jianqi; Cai, Xiaoshu; Riebel, Ulrich

2010-01-01

Transmission fluctuation spectrometry (TFS), as a new method of online and real-time particle analysis developed in recent years, can measure the particle size distribution and particle concentration simultaneously. In the preceding paper, high concentration effects on the TFS using band-pass filters were investigated by numerical simulation, and empirical expressions to correct the effects were obtained. This paper presents a study on the TFS measurements in which the particle concentration varies in a very wide dynamic range. Finally, reasonable results on both the particle size distribution and particle concentration are obtained by introducing empirical corrections into the inversion algorithm

Experimental characterization of a concentrating photovoltaic system varying the light concentration

International Nuclear Information System (INIS)

Renno, C.; Petito, F.; Landi, G.; Neitzert, H.C.

2017-01-01

Highlights: • Experimental characterization of a concentrating photovoltaic system. • Analysis of the point-focus concentrating system performances. • Photovoltaic system parameters as function of the concentration factor. - Abstract: The concentrating photovoltaic system represents one of the most promising solar technologies because it allows a more efficient energy conversion. When a CPV system is designed, the main parameter which has to be considered is the concentration factor that affects both the system energy performances and its configuration. An experimental characterization of a CPV system previously realized at the University of Salerno, is presented in this paper considering several aspects related to the optical configuration, the concentration factor and the solar cell used. In particular, the parameters of an Indium Gallium Phosphide/Gallium Arsenide/Germanium triple-junction solar cell are investigated as function of the concentration factor determined by means of an experimental procedure that uses different optical configurations. The maximum concentration factor reached by the CPV system is 310 suns. The cell parameters dependence on the concentration is reported together with an electroluminescence analysis of the Indium Gallium Phosphide/Gallium Arsenide/Germanium cell. A monitoring of the electrical power provided by the system during its working is also presented corresponding to different direct irradiance values. A mean power of 2.95 W with an average efficiency of 32.8% is obtained referring to a mean irradiance of 930 W/m"2; lower values are obtained when the irradiance is highly fluctuating. The concentrating photovoltaic system electric energy output is estimated considering different concentration levels; the maximal obtained value is 23.5 W h on a sunny day at 310×. Finally, the temperature of the triple-junction solar cell is evaluated for different months in order to evaluate the potential annual thermal energy production

Development of a Hydrologic Characterization Technology for Fault Zones Final Report

Energy Technology Data Exchange (ETDEWEB)

Karasaki, Kenzi [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Onishi, Celia Tiemi [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Doughty, Christine [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Conrad, Mark [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Gasperikova, Erika [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Cook, Paul [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States); Ulrich, Craig [Lawrence Berkeley National Lab. (LBNL), Berkeley, CA (United States)

2012-03-31

This is the final report for the five-year program of the NUMO-LBNL collaborative project (hereafter called the Project): Development of Hydrologic Characterization Technology for Fault Zones, under a NUMO-DOE/LBNL collaboration agreement. Detailed results from the past four years of study can be found in the each year’s year-end report (Karasaki et al., 2008, 2009, 2010, and 2011; Kiho et al., 2008, 2009, 2010, and 2011). In this report, we discuss the results of the studies conducted in FY2011. We also give a summary of the overall results and findings, as well as the lessons learned during the course of the Project.

Further development of vertical-flow final sedimentation tanks; Weiterentwicklung vertikal durchstroemter Nachklaerbecken

Energy Technology Data Exchange (ETDEWEB)

John, K.; Purschke, A.; Schuessler, I. [Mannesmann Seiffert GmbH, Berlin (Germany)

1999-07-01

Because of scarcity of space, the last extension stage of the Berlin-Ruhleben sewage treatment plant was executed with vertical-flow final sedimentation tanks with a square surface. The sedimentation efficiency of these tanks in permanent operation is excellent. In the year past, the operation of such a tank at the limits of its capacity was tested under long-term conditions as a master thesis project with a view to further optimization. Subsequently, this Berlin-type tank was developed further into a multi-cell final sedimentation tank, whose effectiveness was verified by means of flow-technical simulation. (orig.) [German] Im KW Berlin-Ruhleben kamen in der letzten Ausbaustufe infolge sehr begrenzter Bauflaeche vertikal durchstroemte Nachklaerbecken mit quadratischer Oberflaeche zum Einsatz. Diese Becken zeigen im Dauerbetrieb eine hervorragende Klaerwirkung, und im vorigen Jahr wurde im Rahmen einer Diplomarbeit zwecks weiterer Optimierung langfristig unter Betriebsbedingungen die Fahrweise eines solchen Beckens an der Auslegungsgrenze getestet. Unter dem Gesichtspunkt der Kostenreduzierung wurde anschliessend der Typ Berliner Becken zum Mehrzellen-Nachklaerbecken weiterentwickelt und seine Wirksamkeit mittels stroemungstechnischer Simulation ueberprueft. (orig.)

An international database of radionuclide concentration ratios for wildlife: development and uses

International Nuclear Information System (INIS)

Copplestone, D.; Beresford, N.A.; Brown, J.E.; Yankovich, T.

2013-01-01

A key element of most systems for assessing the impact of radionuclides on the environment is a means to estimate the transfer of radionuclides to organisms. To facilitate this, an international wildlife transfer database has been developed to provide an online, searchable compilation of transfer parameters in the form of equilibrium-based whole-organism to media concentration ratios. This paper describes the derivation of the wildlife transfer database, the key data sources it contains and highlights the applications for the data. -- Highlights: • An online database containing wildlife radionuclide transfer parameters is described. • Database underpins recent ICRP and IAEA data wildlife transfer compilations. • Database contains equilibrium based whole organism to media concentration ratios

Development of an instantaneous local fuel-concentration measurement probe: an engine application

Science.gov (United States)

Guibert, P.; Boutar, Z.; Lemoyne, L.

2003-11-01

This work presents a new tool which can deliver instantaneous local measurements of fuel concentration in an engine cylinder with a high temporal resolution, particularly during compression strokes. Fuel concentration is represented by means of equivalence fuel-air ratio, i.e. the real engine mass ratio of fuel to air divided by the same ratio in ideal stoichiometry conditions. Controlling the mixture configuration for any strategy in a spark ignition engine and for auto-ignition combustion has a dominant effect on the subsequent processes of ignition, flame propagation and auto-ignition combustion progression, pollutant formation under lean or even stoichiometric operating conditions. It is extremely difficult, under a transient operation, to control the equivalence air/fuel ratio precisely at a required value and at the right time. This requires the development of a highly accurate equivalence air/fuel ratio control system and a tool to measure using crank angle (CA) resolution. Although non-intrusive laser techniques have considerable advantages, they are most of the time inappropriate due to their optical inaccessibility or the complex experimental set-up involved. Therefore, as a response to the demand for a relatively simple fuel-concentration measurement system a probe is presented that replaces a spark plug and allows the engine to run completely normally. The probe is based on hot-wire like apparatus, but involves catalytic oxidation at the wire surface. The development, characteristics and calibration of the probe are presented followed by applications to in-cylinder engine measurements.

Development of a selective surface vacuum collector. Final report

Energy Technology Data Exchange (ETDEWEB)

de Waal, H.; Simonis, F.

1980-01-01

To make solar energy useful for cooling applications a flat plate high performance collector, which can supply solar energy at 100 to 150/sup 0/C, has been developed. To achieve a reasonable efficiency at these temperatures the thermal heat loss must be very small. This has been obtained by (1) concentration of sunlight (c = 1.6); (2) evacuation of the collector housing to eliminate convection currents (pressure less than or equal to 4kPa); (3) spectral selective coating on the absorber; and (4) a low conductive gas in the collector housing (pressure approx. = 2kPa). The collector consists of a metal box with a glass cover hermetically sealed to it in the way double glazing units are manufactured. The sides of the V-trough concentrators support the glass cover. Measurements have been performed concerning heat loss factor and durability of the vacuum. The first prototype, fitted with a spectral selective coating of tin-oxide on enameled steel (epsilon = 0.25) showed a heat-loss of 2.0 W/m/sup 2/ /sup 0/C at 90/sup 0/C, being in reasonable agreement with calculations. Improvements with respect to the spectral selective coating and the use of a low conductive gas are necessary and will lead to a heat loss factor of about 1 W/m/sup 2/ /sup 0/C. Measurements have shown that in the chosen system the desired vacuum level can be maintained for at least 10 to 15 years.

Developing an interactive computational system to simulate radon concentration inside ancient egyptian tombs

Energy Technology Data Exchange (ETDEWEB)

Metwally, S M; Salama, E; El-Fikia, S A [Faculty of Science, Department of Physics, Ain Shams University, P. O. Box 11566, Cairo (Egypt); Abo-EImagd, M; Eissa, H M [National Institute for Standard, Radiation Measurements Department, P. O. Box 136Giza code no. 12211 RSSP (Egypt)

2007-06-15

RSSP (Radon Scale Software Package) is an interactive support system that simulates the radon concentration inside ancient Egyptian tombs and the consequences on the population in terms of internal and external exposure. RSSP consists of three interconnected modules: the first one simulates the radon concentration inside ancient Egyptian tombs using a developed mathematical model. This model introduces the possibility of controlling the rate of radon accumulation via additional artificial ventilation systems. The source of inputs is an editable database for the tombs includes the geometrical dimensions and some environmental parameters like temperature and outdoor radon concentration at the tombs locations. The second module simulates the absorbed dose due to internal exposure of radon and its progeny. The third module simulates the absorbed dose due to external exposure of Gamma rays emitted from the tomb wall rocks. RSSP introduces the facility of following the progress of radon concentration as well as Internal and external absorbed dose in a wide range of time (seconds, minutes, hours and days) via numerical data and the corresponding graphical interface.

Developing an interactive computational system to simulate radon concentration inside ancient egyptian tombs

International Nuclear Information System (INIS)

Metwally, S. M.; Salama, E.; El-Fikia, S. A.; Abo-EImagd, M.; Eissa, H. M.

2007-01-01

RSSP (Radon Scale Software Package) is an interactive support system that simulates the radon concentration inside ancient Egyptian tombs and the consequences on the population in terms of internal and external exposure. RSSP consists of three interconnected modules: the first one simulates the radon concentration inside ancient Egyptian tombs using a developed mathematical model. This model introduces the possibility of controlling the rate of radon accumulation via additional artificial ventilation systems. The source of inputs is an editable database for the tombs includes the geometrical dimensions and some environmental parameters like temperature and outdoor radon concentration at the tombs locations. The second module simulates the absorbed dose due to internal exposure of radon and its progeny. The third module simulates the absorbed dose due to external exposure of Gamma rays emitted from the tomb wall rocks. RSSP introduces the facility of following the progress of radon concentration as well as Internal and external absorbed dose in a wide range of time (seconds, minutes, hours and days) via numerical data and the corresponding graphical interface

Development of an advanced continuous mild gasification process for the production of coproducts. Final report

Energy Technology Data Exchange (ETDEWEB)

Merriam, N.W.; Jha, M.C.

1991-11-01

This report is a final brief summary of development of a mild-gasification and char conversion process. Morgantown Energy Technology Center developed a concept called mild gasification. In this concept, devolatilization of coal under nonoxidizing and relatively mild temperature and pressure conditions can yield three marketable products: (1) a high-heating-value gas, (2) a high-aromatic coal liquid, and (3) a high-carbon char. The objective of this program is to develop an advanced, continuous, mild-gasification process to produce products that will make the concept economically and environmentally viable. (VC)

Neonatal thyroid-stimulating hormone concentration and psychomotor development at preschool age.

Science.gov (United States)

Trumpff, Caroline; De Schepper, Jean; Vanderfaeillie, Johan; Vercruysse, Nathalie; Van Oyen, Herman; Moreno-Reyes, Rodrigo; Tafforeau, Jean; Vandevijvere, Stefanie

2016-12-01

Thyroid hormones are essential for normal brain development. The aim of this study is to assess if high concentration of thyroid stimulating hormone (TSH) that is below the clinical threshold (5-15 mIU/L) at neonatal screening is linked to psychomotor development impairments in the offspring at preschool age. A total of 284 Belgian preschool children 4-6 years old and their mothers were included in the study. The children were randomly selected from the total list of neonates screened in 2008, 2009 and 2010 by the Brussels newborn screening centre. The sampling was stratified by gender and TSH range (0.45-15 mIU/L). Infants with congenital hypothyroidism (>15 mIU/L), low birth weight and/or prematurity were excluded. Psychomotor development was assessed using the Charlop-Atwell scale of motor coordination. The iodine status of children was determined using median urinary iodine concentration. Socioeconomic, parental and child potential confounding factors were measured through a self-administered questionnaire. TSH level was not significantly associated with total motor score (average change in z-score per unit increase in TSH is 0.02 (-0.03, 0.07), p=0.351), objective motor score (p=0.794) and subjective motor score (p=0.124). No significant associations were found using multivariate regression model to control confounding factors. Mild thyroid dysfunction in the newborn-reflected by an elevation of TSH that is below the clinical threshold (5-15 mIU/L)-was not associated with impaired psychomotor development at preschool age. Published by the BMJ Publishing Group Limited. For permission to use (where not already granted under a licence) please go to http://www.bmj.com/company/products-services/rights-and-licensing/.

Legal problems inherent in the development of geopressured and geothermal resources in Louisiana. Final report

Energy Technology Data Exchange (ETDEWEB)

Harrell, T.A.; Pike, R.W.; Wilkins, B.; Hill, T.M.

1978-03-01

The legal framework within which the geopressured resource will have to be developed in Louisiana is discussed generally. Those problems which may be created by its development within that framework are identified. Where possible, solutions are offered to those problems or at least techniques or devices are indicated which might be considered in their resolution. Finally, a compendium is assembled of those statutory or regulatory provisions which may regulate or affect the resource to the end that it might serve as a handbook for the evaluation of the legal and institutional problems which will face a prospective developer, when and if the resource development is undertaken in Louisiana. (MHR)

Processing development for ceramic structural components: the influence of a presintering of silicon on the final properties of reaction bonded silicon nitride. Final technical report

Energy Technology Data Exchange (ETDEWEB)

1982-03-01

The influence of a presintering of silicon on the final properties of reaction bonded silicon nitride has been studied using scanning electron and optical microscopy, x-ray diffraction analysis, 4 pt. bend test, and mecury intrusion porosimetry. It has been shown that presintering at 1050/sup 0/C will not affect the final nitrided properties. At 1200/sup 0/C, the oxide layer is removed, promoting the formation of B-phase silicon nitride. Presintering at 1200/sup 0/C also results in compact weight loss due to the volatilization of silicon, and the formation of large pores which severely reduce nitrided strength. The development of the structure of sintered silicon compacts appears to involve a temperature gradient, with greater sintering observed near the surface.

Program Development Plan and Team up; FINAL

International Nuclear Information System (INIS)

Solar Electric Power Association

2001-01-01

The final summary report is a comprehensive view of TEAM-UP, with documented data, information, and experiences that SEPA has collected throughout the program, including lessons learned by participating ventures, and sections covering costs and other information on both large and small systems. This report also covers the barriers that TEAM-UP faced to PV commercialization at the beginning of the program, barriers the project was able to remove or reduce, and what barriers remain on the road ahead

Neutron activation analysis of final molasses from cuban sugar industry

International Nuclear Information System (INIS)

Griffith, J.; Gonzalez, E.; Rosenberg, R.J.; Diaz-Rizo, O.

1996-01-01

Thermal and epithermal non-destructive activation analyses have been performed on samples of final molasses from 14 different sugar factories , covering the most important regions in Cuba. From the first measurement after irradiation at the Triga Mark reactor (VTT), the concentration of more than 15 elements is reported. The almost constant elemental composition shows that they can be used equally for different purposes as animal foodstuff and for the manufacture of biotechnological products. This work is part of a research project developed in order to establish a complete characterization of Cuban sugar molasses. (author). 7 refs., 2 tabs

Final environmental impact statement, Beaufort Sea oil and gas development/Northstar Project. Appendix A: BP Exploration (Alaska) Inc. Final project description - Revision 1, March 27, 1997

International Nuclear Information System (INIS)

1999-02-01

BP Exploration (Alaska) Inc. (BPXA) submitted a permit application to the US Army Engineer District, Alaska to initiate the review process for BPXA's plans to develop and produce oil and gas from the Northstar Unit. This report contains Appendix A of an Environmental Impact Statement which was undertaken to identify and evaluate the potential effects the proposed project may have on the environment. This document is the Northstar Development Project, Final Project Description, Revision 1 for BPXA Northstar Project

Technical Report (Final): Development of Solid State Reagents for Preparing Radiolabeled Imaging Agents

Energy Technology Data Exchange (ETDEWEB)

Kabalka, George W

2011-05-20

The goal of this research was on the development of new, rapid, and efficient synthetic methods for incorporating short-lived radionuclides into agents of use in measuring dynamic processes. The initial project period (Year 1) was focused on the preparation of stable, solid state precursors that could be used to efficiently incorporate short-lived radioisotopes into small molecules of use in biological applications (environmental, plant, and animal). The investigation included development and evaluation of new methods for preparing carbon-carbon and carbon-halogen bonds for use in constructing the substrates to be radiolabeled. The second phase (Year 2) was focused on developing isotope incorporation techniques using the stable, boronated polymeric precursors. The final phase (Year 3), was focused on the preparation of specific radiolabeled agents and evaluation of their biodistribution using micro-PET and micro-SPECT. In addition, we began the development of a new series of polymeric borane reagents based on polyethylene glycol backbones.

Estradiol and endocrine disrupting compounds adversely affect development of sea urchin embryos at environmentally relevant concentrations

International Nuclear Information System (INIS)

Roepke, Troy A.; Snyder, Mark J.; Cherr, Gary N.

2005-01-01

Environmental endocrine disrupting compounds (EDCs) are a wide variety of chemicals that typically exert effects, either directly or indirectly, through receptor-mediated processes, thus mimicking endogenous hormones and/or inhibiting normal hormone activities and metabolism. Little is known about the effects of EDCs on echinoderm physiology, reproduction and development. We exposed developing sea urchin embryos (Strongylocentrotus purpuratus and Lytechinus anamesus) to two known EDCs (4-octylphenol (OCT), bisphenol A (BisA)) and to natural and synthetic reproductive hormones (17β-estradiol (E 2 ), estrone (E 1 ), estriol (E 3 ), progesterone (P 4 ) and 17α-ethynylestradiol (EE 2 )). In addition, we studied two non-estrogenic EDCs, tributyltin (TBT) and o,p-DDD. Successful development to the pluteus larval stage (96 h post-fertilization) was used to define EDC concentration-response relationships. The order of compound potency based on EC 50 values for a reduction in normal development was as follows: TBT L.anamesus > OCT > TBT S. p urpuratus >> E 2 > EE 2 > DDD >> BisA > P 4 > E 1 >> E 3 . The effect of TBT was pronounced even at concentrations substantially lower than those commonly reported in heavily contaminated areas, but the response was significantly different in the two model species. Sea urchin embryos were generally more sensitive to estrogenic EDCs and TBT than most other invertebrate larvae. Stage-specific exposure experiments were conducted to determine the most sensitive developmental periods using blastula, gastrula and post-gastrula (pluteus) stages. The stage most sensitive to E 2 , OCT and TBT was the blastula stage with less overall sensitivity in the gastrula stage, regardless of concentration. Selective estrogen receptor modulators (SERMs) were added to the experiments individually and in combination with estrogenic EDCs to interfere with potential receptor-mediated actions. Tamoxifen, a partial ER agonist, alone inhibited development at

High Concentration of Melatonin Regulates Leaf Development by Suppressing Cell Proliferation and Endoreduplication in Arabidopsis.

Science.gov (United States)

Wang, Qiannan; An, Bang; Shi, Haitao; Luo, Hongli; He, Chaozu

2017-05-05

N -acetyl-5-methoxytryptamine (Melatonin), as a crucial messenger in plants, functions in adjusting biological rhythms, stress tolerance, plant growth and development. Several studies have shown the retardation effect of exogenous melatonin treatment on plant growth and development. However, the in vivo role of melatonin in regulating plant leaf growth and the underlying mechanism are still unclear. In this study, we found that high concentration of melatonin suppressed leaf growth in Arabidopsis by reducing both cell size and cell number. Further kinetic analysis of the fifth leaves showed that melatonin remarkably inhibited cell division rate. Additionally, flow cytometic analysis indicated that melatonin negatively regulated endoreduplication during leaf development. Consistently, the expression analysis revealed that melatonin regulated the transcriptional levels of key genes of cell cycle and ribosome. Taken together, this study suggests that high concentration of melatonin negatively regulated the leaf growth and development in Arabidopsis , through modulation of endoreduplication and the transcripts of cell cycle and ribosomal key genes.

EPR measurements of phenolic concentration in developing red grapeseeds - a pilot study

International Nuclear Information System (INIS)

Troup, G.J.; Kennedy, J.A.; Hutton, D.R.; Hewitt, D.; Hunter, C.A.; Pilbrow, J.R.; Ristic, R.; Iland, P.; Jones, G.P. Anon

2000-01-01

Full text: Phenolics, in the liquid (wine, Troup et al., Free Radicals Research, 1994, 20, 63 - 68) and solid state, give stable free radical signals detectable by EPR. Observations of EPR signals (partly due to phenolics) in developing red grapeseeds, as a function of time, have been made. The increasing, then decreasing of this signal as a function of time correlates well with the theory of phenolic concentration in developing grapeseeds recently proposed by Kennedy et al. (in press). This is a very significant application of EPR Spectroscopy in the Wine Industry, so far unfamiliar with its use

Measuring concentrations of selected air pollutants inside California vehicles. Final report

International Nuclear Information System (INIS)

Rodes, C.; Sheldon, L.; Whitaker, D.; Clayton, A.; Fitzgerald, K.

1999-01-01

This project measured 2-hour integrated concentrations of PM10, PM2.5, metals and a number of organic chemicals including benzene and MTBE inside vehicles on California roadways. Using continuous samplers, particle counts, black carbon, and CO were also measured. In addition to measuring in-vehicle levels, the investigators measured pollutant levels just outside the vehicle, at roadside stations, and ambient air monitoring stations. Different driving scenarios were designed to assess the effects of a number of factors on in-vehicle pollutant levels. These factors included roadway type, carpool lanes, traffic conditions, geographical locations, vehicle type, and vehicle ventilation conditions. The statewide average in-vehicle concentrations of benzene, MTBE, and formaldehyde ranged from 3--22 microg/m 3 , 3--90 microg/m 3 , and 0---22 microg/m 3 , respectively. The ranges of mean PM10 and PM2.5 in-vehicle levels in Sacramento were 20--40 microg/m 3 and 6--22 microg/m 3 , respectively. In general, pollutant levels inside or just outside the vehicles were higher than those measured at the roadside stations or the ambient air stations. In-vehicle pollutant levels were consistently higher in Los Angeles than Sacramento. Pollutant levels measured inside vehicles traveling in a carpool lane were much lower than those in the right-hand, slower lanes. Under the study conditions, factors such as vehicle type and ventilation and little effect on in-vehicle pollutant levels. Other factors, such as roadway type, freeway congestion level, and time-of-day had some influence on in-vehicle pollution levels

Final Report on the Operation and Maintenance Improvement Program for Concentrating Solar Power Plants

International Nuclear Information System (INIS)

Cohen, Gilbert E.; Kearney, David W.; Kolb, Gregory J.

1999-01-01

This report describes the results of a six-year, $6.3 million project to reduce operation and maintenance (O ampersand M) costs at power plants employing concentrating solar power (CSP) technology. Sandia National Laboratories teamed with KJC Operating Company to implement the O ampersand M Improvement Program. O ampersand M technologies developed during the course of the program were demonstrated at the 150-MW Kramer Junction solar power park located in Boron, California. Improvements were made in the following areas: (a) efficiency of solar energy collection, (b) O ampersand M information management, (c) reliability of solar field flow loop hardware, (d) plant operating strategy, and (e) cost reduction associated with environmental issues. A 37% reduction in annual O ampersand M costs was achieved. Based on the lessons learned, an optimum solar- field O ampersand M plan for future CSP plants is presented. Parabolic trough solar technology is employed at Kramer Junction. However, many of the O ampersand M improvements described in the report are also applicable to CSP plants based on solar power tower or dish/engine concepts

Final Report on the Operation and Maintenance Improvement Program for Concentrating Solar Power Plants

Energy Technology Data Exchange (ETDEWEB)

Cohen Gilbert E.; Kearney, David W.; Kolb, Gregory J.

1999-06-01

This report describes the results of a six-year, $6.3 million project to reduce operation and maintenance (O&M) costs at power plants employing concentrating solar power (CSP) technology. Sandia National Laboratories teamed with KJC Operating Company to implement the O&M Improvement Program. O&M technologies developed during the course of the program were demonstrated at the 150-MW Kramer Junction solar power park located in Boron, California. Improvements were made in the following areas: (a) efficiency of solar energy collection, (b) O&M information management, (c) reliability of solar field flow loop hardware, (d) plant operating strategy, and (e) cost reduction associated with environmental issues. A 37% reduction in annual O&M costs was achieved. Based on the lessons learned, an optimum solar- field O&M plan for future CSP plants is presented. Parabolic trough solar technology is employed at Kramer Junction. However, many of the O&M improvements described in the report are also applicable to CSP plants based on solar power tower or dish/engine concepts.

Membrane/distillation hybrid process research and development. Final report, phase II

Energy Technology Data Exchange (ETDEWEB)

Mazanec, T.J.

1997-07-01

This report covers work conducted under the grant awarded to BP by DOE in late 1991 entitled {open_quotes}Membrane/Distillation Hybrid Process Research and Development.{close_quotes} The program was directed towards development and commercialization of the BP process for separation of vapor phase olefins from non-olefins via facilitated transport using an aqueous facilitator. The program has come to a very successful conclusion, with formation of a partnership between BP and Stone and Webster Engineering Corporation (SWEC) to market and commercialize the technology. The focus of this report is the final portion of the program, during which engineering re-design, facilitator optimization, economic analysis, and marketing have been the primary activities. At the end of Phase II BP was looking to partner with an engineering firm to advance the selective olefin recovery (SOR) technology from the lab/demo stage to full commercialization. In August 1995 BP and SWEC reached an agreement to advance the technology by completing additional Phase III work with DOE and beginning marketing activities.

Transuranic-contaminated solid waste Treatment Development Facility. Final safety analysis report

International Nuclear Information System (INIS)

Warner, C.L.

1979-07-01

The Final Safety Analysis Report (FSAR) for the Transuranic-Contaminated Solid-Waste Treatment Facility has been prepared in compliance with the Department of Energy (DOE) Manual Chapter 0531, Safety of Nonreactor Nuclear Facilities. The Treatment Development Facility (TDF) at the Los Alamos Scientific Laboratory is a research and development facility dedicated to the study of radioactive-waste-management processes. This analysis addresses site assessment, facility design and construction, and the design and operating characteristics of the first study process, controlled air incineration and aqueous scrub off-gas treatment with respect to both normal and accident conditions. The credible accidents having potentially serious consequences relative to the operation of the facility and the first process have been analyzed and the consequences of each postulated credible accident are presented. Descriptions of the control systems, engineered safeguards, and administrative and operational features designed to prevent or mitigate the consequences of such accidents are presented. The essential features of the operating and emergency procedures, environmental protection and monitoring programs, as well as the health and safety, quality assurance, and employee training programs are described

Transuranic-contaminated solid waste Treatment Development Facility. Final safety analysis report

Energy Technology Data Exchange (ETDEWEB)

Warner, C.L. (comp.)

1979-07-01

The Final Safety Analysis Report (FSAR) for the Transuranic-Contaminated Solid-Waste Treatment Facility has been prepared in compliance with the Department of Energy (DOE) Manual Chapter 0531, Safety of Nonreactor Nuclear Facilities. The Treatment Development Facility (TDF) at the Los Alamos Scientific Laboratory is a research and development facility dedicated to the study of radioactive-waste-management processes. This analysis addresses site assessment, facility design and construction, and the design and operating characteristics of the first study process, controlled air incineration and aqueous scrub off-gas treatment with respect to both normal and accident conditions. The credible accidents having potentially serious consequences relative to the operation of the facility and the first process have been analyzed and the consequences of each postulated credible accident are presented. Descriptions of the control systems, engineered safeguards, and administrative and operational features designed to prevent or mitigate the consequences of such accidents are presented. The essential features of the operating and emergency procedures, environmental protection and monitoring programs, as well as the health and safety, quality assurance, and employee training programs are described.

Development of a test set for adjustment of residential furnaces and boilers. Final report

Energy Technology Data Exchange (ETDEWEB)

1980-01-01

A program was undertaken to design and develop a portable test set for simplified field adjustment of residential furnaces and boilers to achieve peak operating efficiency. Advanced technology was applied to provide continuous analysis of flue gases and the display of temperature, oxygen concentrations, smoke value and furnace efficiency. Prototype models were constructed and delivered to Brookhaven National Laboratory for further testing. A survey of furnace dealers was conducted, and a commercialization plan was developed based on survey responses and the status of the equipment developed under the program. Goals for a marketable test set and development steps to achieve a projected energy savings were determined and recommended. Recommendations for specific areas of further development are included.

Development of an on-line analyzer for organic phase uranium concentration in extraction process

International Nuclear Information System (INIS)

Dong Yanwu; Song Yufen; Zhu Yaokun; Cong Peiyuan; Cui Songru

1998-10-01

The working principle, constitution, performance of an on-line analyzer and the development characteristic of immersion sonde, data processing system and examination standard are reported. The performance of this instrument is reliable. For identical sample, the signal fluctuation in continuous monitoring for four months is less than +-1%. According to required measurement range by choosing appropriate length of sample cell the precision of measurement is better than 1% at uranium concentration 100 g/L. The detection limit is (50 +- 10) mg/L. The uranium concentration in process stream can be automatically displayed and printed out in real time and 4∼20 mA current signal being proportional to the uranium concentration can be presented. So the continuous control and computer management for the extraction process can be achieved

Pathway to 50% Efficient Inverted Metamorphic Concentrator Solar Cells

Energy Technology Data Exchange (ETDEWEB)

Geisz, John F [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Steiner, Myles A [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Jain, Nikhil [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Schulte, Kevin L [National Renewable Energy Laboratory (NREL), Golden, CO (United States); France, Ryan M [National Renewable Energy Laboratory (NREL), Golden, CO (United States); McMahon, William E [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Perl, Emmett [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Horowitz, Kelsey A [National Renewable Energy Laboratory (NREL), Golden, CO (United States); Friedman, Daniel J [National Renewable Energy Laboratory (NREL), Golden, CO (United States)

2017-09-06

Series-connected five (5J) and six junction (6J) concentrator solar cell strategies have the realistic potential to exceed 50% efficiency to enable low-cost CPV systems. We propose three strategies for developing a practical 6J device. We have overcome many of the challenges required to build such concentrator solar cell devices: We have developed 2.1 eV AlGaInP, 1.7 eV AlGaAs, and 1.7 eV GaInAsP junctions with external radiative efficiency greater than 0.1%. We have developed a transparent tunnel junction that absorbs minimal light intended for the second junction yet resists degradation under thermal load. We have developed metamorphic grades from the GaAs to the InP lattice constant that are transparent to sub-GaAs bandgap light. We have grown and compared low bandgap junctions (0.7eV - 1.2 eV) using metamorphic GaInAs, metamorphic GaInAsP, and GaInAsP lattice-matched to InP. And finally, we have demonstrated excellent performance in a high voltage, low current 4 junction inverted metamorphic device using 2.1, 1.7, 1.4, and 1.1 eV junctions with over 8.7 mA/cm2 one-sun current density that operates up to 1000 suns without tunnel junction failure.

Estradiol and endocrine disrupting compounds adversely affect development of sea urchin embryos at environmentally relevant concentrations

Energy Technology Data Exchange (ETDEWEB)

Roepke, Troy A. [Bodega Marine Laboratory, University of California, Davis, POB 247, Bodega Bay, CA 94923 (United States); Snyder, Mark J. [Bodega Marine Laboratory, University of California, Davis, POB 247, Bodega Bay, CA 94923 (United States); Cherr, Gary N. [Bodega Marine Laboratory, University of California, Davis, POB 247, Bodega Bay, CA 94923 (United States) and Departments of Environmental Toxicology and Nutrition, One Shields Avenue, University of California, Davis, CA 95616 (United States)]. E-mail: gncherr@ucdavis.edu

2005-01-26

Environmental endocrine disrupting compounds (EDCs) are a wide variety of chemicals that typically exert effects, either directly or indirectly, through receptor-mediated processes, thus mimicking endogenous hormones and/or inhibiting normal hormone activities and metabolism. Little is known about the effects of EDCs on echinoderm physiology, reproduction and development. We exposed developing sea urchin embryos (Strongylocentrotus purpuratus and Lytechinus anamesus) to two known EDCs (4-octylphenol (OCT), bisphenol A (BisA)) and to natural and synthetic reproductive hormones (17{beta}-estradiol (E{sub 2}), estrone (E{sub 1}), estriol (E{sub 3}), progesterone (P{sub 4}) and 17{alpha}-ethynylestradiol (EE{sub 2})). In addition, we studied two non-estrogenic EDCs, tributyltin (TBT) and o,p-DDD. Successful development to the pluteus larval stage (96 h post-fertilization) was used to define EDC concentration-response relationships. The order of compound potency based on EC{sub 50} values for a reduction in normal development was as follows: TBT {sub L.anamesus} > OCT > TBT {sub S.{sub p}}{sub urpuratus} >> E{sub 2} > EE{sub 2} > DDD >> BisA > P{sub 4} > E{sub 1} >> E{sub 3}. The effect of TBT was pronounced even at concentrations substantially lower than those commonly reported in heavily contaminated areas, but the response was significantly different in the two model species. Sea urchin embryos were generally more sensitive to estrogenic EDCs and TBT than most other invertebrate larvae. Stage-specific exposure experiments were conducted to determine the most sensitive developmental periods using blastula, gastrula and post-gastrula (pluteus) stages. The stage most sensitive to E{sub 2}, OCT and TBT was the blastula stage with less overall sensitivity in the gastrula stage, regardless of concentration. Selective estrogen receptor modulators (SERMs) were added to the experiments individually and in combination with estrogenic EDCs to interfere with potential receptor

Development of a central final repository management for the coordination of the waste for Schacht Konrad from public authorities

International Nuclear Information System (INIS)

Graffunder, Iris; Dominke-Bendix, Carola; Waldek, Achim

2012-01-01

The central final repository management is supposed to fulfill the following tasks: active collaboration of Konrad contract draft, signing of internal contracts and agreements, cooperation contract with GNS, cooperation with coordination authorities, inventory taking of wastes (existing inventory and prognosis) and interim storage capacities of public authorities, development of planning and management software, optimization of the final repository documentation, container management, logistics concept, long-term disposal planning and prognosis, planning and coordination of the annual waste amount, management and documentation of disposed waste allocation, coordination of transport schedules, consulting service for waste obligations (final repository requirements, product control, documentation).

Indoor radon concentrations in Vushtrri, Kosovo

International Nuclear Information System (INIS)

Xhafa, B.; Jonuzaj, A.; ); Bekteshi, S.; Ahmetaj, S.; Kabashi, S.; )

2009-01-01

Indoor air radon concentration was measured by exposing trac ketch detectors in the two elementary schools, one high school, a kindergarten and the hospital in the city of Vushtrri. Measurements were performed with the radon monitor PRM-145, which uses alpha scintillation cells and serves to determine the current concentration of radon. The results we obtained are in the range between the average values of radon for the interior spaces, and values that pose a potential risk for lung cancer. Measuring the concentration of radon was done in total of 34 rooms and came up with values which are between 28Bqm -3 and 398Bqm -3 . In order to reduce the concentration of radon, we have built a ventilation pump, then we performed repeated measurements and finally came with results between 130-145Bqm -3 .

Influence of food concentration, temperature and salinity on the larval development of Balanus amphitrite

Digital Repository Service at National Institute of Oceanography (India)

Anil, A.C.; Kurian, J.

Influence of food concentration (0.5, 1 and 2 x 10 sup(5) cell ml sup(-1) of Skeletonema costatum), temperature (20 and 30 degrees C) and salinity (15, 25 and 35 ppt) on the larval development of Balanus amphitrite (Cirripedia: Thoracica...

Mutielemental concentration and physiological responses of Lavandula pedunculata growing in soils developed on different mine wastes.

Science.gov (United States)

Santos, Erika S; Abreu, Maria Manuela; Saraiva, Jorge A

2016-06-01

This study aimed to: i) evaluate the accumulation and translocation patterns of potentially hazardous elements into the Lavandula pedunculata and their influence in the concentrations of nutrients; and ii) compare some physiological responses associated with oxidative stress (concentration of chlorophylls (Chla, Chlb and total), carotenoids, and total protein) and several components involved in tolerance mechanisms (concentrations of proline and acid-soluble thiols and total/specific activity of catalase (CAT) and superoxide dismutase (SOD)), in plants growing in soils with a multielemental contamination and non-contaminated. Composite samples of soils, developed on mine wastes and/or host rocks, and L. pedunculata (roots and shoots) were collected in São Domingos mine (SE of Portugal) and in a reference area with non-contaminated soils, Corte do Pinto, with the same climatic conditions. São Domingos soils had high total concentrations of several hazardous elements (e.g. As and Pb) but their available fractions were small (mainly Lavandula pedunculata plants are able to survive in soils developed on different mine wastes with multielemental contamination and low fertility showing no symptoms (visible and physiological) of phytotoxicity or deficiency. Copyright © 2016 Elsevier Ltd. All rights reserved.

Methodology development to support NPR strategic planning. Final report

International Nuclear Information System (INIS)

1996-01-01

This report covers the work performed in support of the Office of New Production Reactors during the 9 month period from January through September 1990. Because of the rapid pace of program activities during this time period, the emphasis on work performed shifted from the strategic planning emphasis toward supporting initiatives requiring a more immediate consideration and response. Consequently, the work performed has concentrated on researching and helping identify and resolve those issues considered to be of most immediate concern. Even though they are strongly interrelated, they can be separated into two broad categories as follows: The first category encompasses program internal concerns. Included are issues associated with the current demand for accelerating staff growth, satisfying the immediate need for appropriate skill and experience levels, team building efforts necessary to assure the development of an effective operating organization, ability of people and organizations to satisfactorily understand and execute their assigned roles and responsibilities, and the general facilitation of inter/intra organization communications and working relationships. The second category encompasses program execution concerns. These include those efforts required in development of realistic execution plans and implementation of appropriate control mechanisms which provide for effective forecasting, planning, managing, and controlling of on-going (or soon to be) program substantive activities according to the master integrated schedule and budget

Inelastic X-ray Scattering Beamline Collaborative Development Team Final Report

International Nuclear Information System (INIS)

Burns, Clement

2008-01-01

This is the final report for the project to create a beam line for inelastic x-ray scattering at the Advanced Photon Source. The facility is complete and operating well, with spectrometers for both high resolution and medium resolution measurements. With the advent of third generation synchrotron sources, inelastic x-ray scattering (IXS) has become a valuable technique to probe the electronic and vibrational states of a wide variety of systems of interest in physics, chemistry, and biology. IXS is a weak probe, and experimental setups are complex and require well-optimized spectrometers which need a dedicated beamline to function efficiently. This project was the result of a proposal to provide a world-class, user friendly beamline for IXS at the Advanced Photon Source. The IXS Collaborative Development Team (IXS-CDT) was formed from groups at the national laboratories and a number of different universities. The beamline was designed from the front end to the experimental stations. Two different experimental stations were provided, one for medium resolution inelastic x-ray scattering (MERIX) and a spectrometer for high resolution inelastic x-ray scattering (HERIX). Funding for this project came from several sources as well as the DOE. The beamline is complete with both spectrometers operating well. The facility is now open to the general user community and there has been a tremendous demand to take advantage of the beamline's capabilities. A large number of different experiments have already been carried out on the beamline. A detailed description of the beamline has been given in the final design report (FDR) for the beamline from which much of the material in this report came. The first part of this report contains a general overview of the project with more technical details given later.

Sensor development for in situ detection of concentration polarization and fouling of reverse osmosis membranes

Science.gov (United States)

Detrich, Kahlil T.; Goulbourne, Nakhiah C.

2009-03-01

The purpose of this research is to evaluate three polymer electroding techniques in developing a novel in situ sensor for an RO system using the electrical response of a thin film composite sensor. Electrical impedance spectroscopy (EIS) was used to measure the sensor response when exposed to sodium chloride solutions with concentrations from 0.1 M to 0.8 M in both single and double bath configurations. An insulated carbon grease sensor was mechanically stable while a composite Direct Assembly Process (DAP) sensor was fragile upon hydration. Scanning electron microscopy results from an impregnation-reduction technique showed gold nanoparticles were deposited most effectively when presoaked in a potassium hydroxide solution and on an uncoated membrane; surface resistances remained too high for sensor implementation. Through thickness carbon grease sensors showed a transient response to changes in concentration, and no meaningful concentration sensitivity was noted for the time scales over which EIS measurements were taken. Surface carbon grease electrodes attached to the polyamide thin film were not sensitive to concentration. The impedance spectra indicated the carbon grease sensor was unable to detect changes in concentration in double bath experiments when implemented with the polyamide surface exposed to salt solutions. DAP sensors lacked a consistent response to changes in concentration too. A reverse double bath experiment with the polysulfone layer exposed to a constant concentration exhibited a transient impedance response similar to through thickness carbon grease sensors in a single bath at constant concentration. These results suggest that the microporous polysulfone layer is responsible for sensor response to concentration.

Development of telemetry for high-speed rotor instrumentation and monitoring: Final report

Energy Technology Data Exchange (ETDEWEB)

Mallick, G.T.; Nenno, P.N.; Parker, J.H.; Eckels, P.W.

1987-06-01

A modern data acquisition and telemetry system for rotating systems was developed as a part of a program, jointly funded by EPRI and Westinghouse, to develop a 300 MVA superconducting generator. While the overall program was terminated before completion, the telemetry development task was essentially complete at termination. It had been planned that the data acquisition and telemetry system was to be used in large scale models and the final 300 MVA rotor testing for transmitting sensor data from the rotating frame. An important part of this development was the qualification of a number of cryogenic sensors that were to be used in conjunction with the telemetry system for measuring temperature, strain and liquid helium level. The telemetry system that was developed handled the data transmission by digital frequency shift keying with a carrier of 200 kHz. The analog sensor signals were amplified and filtered ''on-board'' before being multiplexed and converted to a digital signal. All of this was under the control of a single chip microcomputer (Intel 8748) in the rotating frame. The overall sensor, data acquisition and telemetry system were operated and tested under rotation for a period of over one hundred hours. Overall, the system has proven itself to be reliable and effective. The present report covers all aspects of this development in detail, including the circuit and software design and performance. 27 refs., 58 figs.

SLC Final Performance and Lessons

International Nuclear Information System (INIS)

Phinney, Nan

2000-01-01

The Stanford Linear Collider (SLC) was the first prototype of a new type of accelerator, the electron-positron linear collider. Many years of dedicated effort were required to understand the physics of this new technology and to develop the techniques for maximizing performance. Key issues were emittance dilution, stability, final beam optimization and background control. Precision, non-invasive diagnostics were required to measure and monitor the beams throughout the machine. Beam-based feedback systems were needed to stabilize energy, trajectory, intensity and the final beam size at the interaction point. variety of new tuning techniques were developed to correct for residual optical or alignment errors. The final focus system underwent a series of refinements in order to deliver sub-micron size beams. It also took many iterations to understand the sources of backgrounds and develop the methods to control them. The benefit from this accumulated experience was seen in the performance of the SLC during its final run in 1997-98. The luminosity increased by a factor of three to 3*10 30 and the 350,000 Z data sample delivered was nearly double that from all previous runs combined

Chemical Utilization of Albizia lebbeck Leaves for Developing Protein Concentrates as a Dietary Supplement.

Science.gov (United States)

Khan, Lutful Haque; Varshney, V K

2017-08-17

In search of nonconventional sources of protein to combat widespread malnutrition, the possibility of developing a protein concentrate as an alternative dietary supplement from abundantly available yet poorly valorized leaves of Albizia lebbeck (siris) was examined. A process for recovery of leaf protein concentrate (LPC) from these leaves was optimized and applied for isolation of LPCs from lower, middle, and upper canopies of the tree. The optimized conditions (leaves to water 1:9, coagulation at pH 4.0 using 1 N citric acid at 90°C for 11 minutes) afforded LPCs containing protein 37.15%, 37.57%, and 37.76% in 5.99%, 5.97%, and 6.07% yield, respectively. The proximate nutritional composition, pigments, minerals, in vitro digestibility, and antinutritional factors of these LPCs were determined. Analysis of variance of these data revealed no significant difference with respect to canopy. Use of Albizia lebbeck leaves for development of LPC as a food/feed supplement was revealed.

The association between economic development, lifestyle differentiation, and C-reactive protein concentration within rural communities in Hainan Island, China.

Science.gov (United States)

Inoue, Yosuke; Stickley, Andrew; Yazawa, Aki; Li, Dandan; Du, Jianwei; Jin, Yuming; Chen, Yan; Watanabe, Chiho

2016-01-01

Earlier fieldwork in rural areas of Hainan Island, China, demonstrated that during the course of economic development increasing differences had emerged in lifestyles within communities. It is possible that these variations might have stratified residents into subpopulations with different health attributes. This study examined the association between C-reactive protein (CRP) concentration, a biomarker of future cardiovascular events, and personal lifestyle parameters and the degree of community-level economic development among rural communities. A cross-sectional field survey was undertaken in 19 rural communities in Hainan. Convenience sampling was used to recruit 1,744 participants. Dried blood spot samples were collected to measure high-sensitivity CRP concentration. Sex-stratified multilevel regression analyses were conducted to identify factors associated with CRP concentration among the participants. While CRP concentration was negatively associated with being married and (more) education among men, for women CRP concentration was associated with the frequency of poultry consumption (P = 0.014) and the experience of migratory work in the previous year (P = 0.009). In addition, for females, living in communities with a greater degree of inequality, as indexed by the Gini coefficient, was also associated with increased CRP concentration (P = 0.003). Given that CRP concentration is a marker of future CVD risk, this study suggests that within these previously homogenous rural communities, economic development might have stratified people into population subgroups with a different CVD risk. © 2015 Wiley Periodicals, Inc.

Design of the support structure, drive pedestal, and controls for a solar concentrator

Energy Technology Data Exchange (ETDEWEB)

Goldberg, V.R.; Ford, J.L.; Anderson, A.E. (WG Associates, Dallas, TX (United States))

1991-08-01

The glass/metal McDonnell-Douglas dish is the state-of-the-art of parabolic dish concentrators. Because of the perceived high production cost of this concentrator, the Department of Energy's Solar Thermal Program is developing stretch-membrane technology for large (75 kWt) solar concentrators for integration with receivers and engines in 25 kWe dish-Stirling systems. The objective of this development effort is to reduce the cost of the concentrator while maintaining the high levels of performance characteristic of glass-metal dishes. Under contract to Sandia National Laboratories, Science Applications International Corporation, Solar Kinetics Inc. and WG Associates are developing a faceted stretched-membrane heliostat technology. This design will result in a low-risk, near-term concentrator for dish-Stirling systems. WG Associates has designed the support structure, drives and tracking controls for this dish. The structure is configured to support 12 stretched-membrane, 3.5-meter diameter facets in a shaped dish configuration. The dish design is sized to power a dish-Stirling system capable of producing 25 kW (electric). In the design of the structure, trade-off studies were conducted to determine the best'' facet arrangement, dish contour, dish focal length, tracking control and walk-off protection. As part of the design, in-depth analyses were performed to evaluate pointing accuracy, compliance with AISC steel design codes, and the economics of fabrication and installation. Detailed fabrication and installation drawings were produced, and initial production cost estimates for the dish were developed. These issues, and the final dish design, are presented in this report. 7 refs., 33 figs., 18 tabs.

Development of models and online diagnostic monitors of the high-temperature corrosion of refractories in oxy/fuel glass furnaces : final project report.

Energy Technology Data Exchange (ETDEWEB)

Griffiths, Stewart K.; Gupta, Amul (Monofrax Inc., Falconer, NY); Walsh, Peter M.; Rice, Steven F.; Velez, Mariano (University of Missouri, Rolla, MO); Allendorf, Mark D.; Pecoraro, George A. (PPG Industries, Inc., Pittsburgh, PA); Nilson, Robert H.; Wolfe, H. Edward (ANH Refractories, Pittsburgh, PA); Yang, Nancy Y. C.; Bugeat, Benjamin () American Air Liquide, Countryside, IL); Spear, Karl E. (Pennsylvania State University, University Park, PA); Marin, Ovidiu () American Air Liquide, Countryside, IL); Ghani, M. Usman (American Air Liquide, Countryside, IL)

2005-02-01

This report summarizes the results of a five-year effort to understand the mechanisms and develop models that predict the corrosion of refractories in oxygen-fuel glass-melting furnaces. Thermodynamic data for the Si-O-(Na or K) and Al-O-(Na or K) systems are reported, allowing equilibrium calculations to be performed to evaluate corrosion of silica- and alumina-based refractories under typical furnace operating conditions. A detailed analysis of processes contributing to corrosion is also presented. Using this analysis, a model of the corrosion process was developed and used to predict corrosion rates in an actual industrial glass furnace. The rate-limiting process is most likely the transport of NaOH(gas) through the mass-transport boundary layer from the furnace atmosphere to the crown surface. Corrosion rates predicted on this basis are in better agreement with observation than those produced by any other mechanism, although the absolute values are highly sensitive to the crown temperature and the NaOH(gas) concentration at equilibrium and at the edge of the boundary layer. Finally, the project explored the development of excimer laser induced fragmentation (ELIF) fluorescence spectroscopy for the detection of gas-phase alkali hydroxides (e.g., NaOH) that are predicted to be the key species causing accelerated corrosion in these furnaces. The development of ELIF and the construction of field-portable instrumentation for glass furnace applications are reported and the method is shown to be effective in industrial settings.

Simulant Development for LAWPS Testing

Energy Technology Data Exchange (ETDEWEB)

Russell, Renee L. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Schonewill, Philip P. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States); Burns, Carolyn A. [Pacific Northwest National Lab. (PNNL), Richland, WA (United States)

2017-05-23

This report describes simulant development work that was conducted to support the technology maturation of the LAWPS facility. Desired simulant physical properties (density, viscosity, solids concentration, solid particle size), sodium concentrations, and general anion identifications were provided by WRPS. The simulant recipes, particularly a “nominal” 5.6M Na simulant, are intended to be tested at several scales, ranging from bench-scale (500 mL) to full-scale. Each simulant formulation was selected to be chemically representative of the waste streams anticipated to be fed to the LAWPS system, and used the current version of the LAWPS waste specification as a formulation basis. After simulant development iterations, four simulants of varying sodium concentration (5.6M, 6.0M, 4.0M, and 8.0M) were prepared and characterized. The formulation basis, development testing, and final simulant recipes and characterization data for these four simulants are presented in this report.

36 CFR 908.33 - Final determination.

Science.gov (United States)

2010-07-01

... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Final determination. 908.33... DEVELOPMENT AREA Review Procedure § 908.33 Final determination. (a) The Chairman or designee(s) shall make a final determination on the claim within 45 days of receipt of the file from the Director of Real Estate...

Airport Solar Photovoltaic Concentrator Project. Phase 1 - final report, June 1, 1978-February 28, 1979

Energy Technology Data Exchange (ETDEWEB)

1979-12-01

The system design, analysis, and specification, site preparation, and operation and evaluation plan for a 500 kWe photovoltaic power supply to be located at the Phoenix Sky Harbor International Airport in Phoenix, Arizona, are presented. The solar cell arrays are concentrator silicon solar cells with tracking 70X Cassegrain-type concentrators. The power conditioning system, tracking system, and control systems are described in detal. Environmental impact studies are described. Component specifications and drawings are included. (WHK)

Bayesian Estimation of the Active Concentration and Affinity Constants Using Surface Plasmon Resonance Technology.

Directory of Open Access Journals (Sweden)

Feng Feng

Full Text Available Surface plasmon resonance (SPR has previously been employed to measure the active concentration of analyte in addition to the kinetic rate constants in molecular binding reactions. Those approaches, however, have a few restrictions. In this work, a Bayesian approach is developed to determine both active concentration and affinity constants using SPR technology. With the appropriate prior probabilities on the parameters and a derived likelihood function, a Markov Chain Monte Carlo (MCMC algorithm is applied to compute the posterior probability densities of both the active concentration and kinetic rate constants based on the collected SPR data. Compared with previous approaches, ours exploits information from the duration of the process in its entirety, including both association and dissociation phases, under partial mass transport conditions; do not depend on calibration data; multiple injections of analyte at varying flow rates are not necessary. Finally the method is validated by analyzing both simulated and experimental datasets. A software package implementing our approach is developed with a user-friendly interface and made freely available.

Development of an international safeguards approach to the final disposal of spent fuel in geological repositories

International Nuclear Information System (INIS)

Murphey, W.M.; Moran, B.W.; Fattah, A.

1996-01-01

The International Atomic Energy Agency (IAEA) is currently pursuing development of an international safeguards approach for the final disposal of spent fuel in geological repositories through consultants meetings and through the Program for Development of Safeguards for Final Disposal of Spent Fuel in Geological Repositories (SAGOR). The consultants meetings provide policy guidance to IAEA; SAGOR recommends effective approaches that can be efficiently implemented by IAEA. The SAGOR program, which is a collaboration of eight Member State Support Programs (MSSPs), was initiated in July 1994 and has identified 15 activities in each of three areas (i.e. conditioning facilities, active repositories, and closed repositories) that must be performed to ensure an efficient, yet effective safeguards approach. Two consultants meetings have been held: the first in May 1991 and the last in November 1995. For nuclear materials emplaced in a geological repository, the safeguards objectives were defined to be (1) to detect the diversion of spent fuel, whether concealed or unconcealed, from the repository and (2) to detect undeclared activities of safeguards concern (e.g., tunneling, underground reprocessing, or substitution in containers)

Performance analysis of high-concentrated multi-junction solar cells in hot climate

Science.gov (United States)

Ghoneim, Adel A.; Kandil, Kandil M.; Alzanki, Talal H.; Alenezi, Mohammad R.

2018-03-01

Multi-junction concentrator solar cells are a promising technology as they can fulfill the increasing energy demand with renewable sources. Focusing sunlight upon the aperture of multi-junction photovoltaic (PV) cells can generate much greater power densities than conventional PV cells. So, concentrated PV multi-junction solar cells offer a promising way towards achieving minimum cost per kilowatt-hour. However, these cells have many aspects that must be fixed to be feasible for large-scale energy generation. In this work, a model is developed to analyze the impact of various atmospheric factors on concentrator PV performance. A single-diode equivalent circuit model is developed to examine multi-junction cells performance in hot weather conditions, considering the impacts of both temperature and concentration ratio. The impacts of spectral variations of irradiance on annual performance of various high-concentrated photovoltaic (HCPV) panels are examined, adapting spectra simulations using the SMARTS model. Also, the diode shunt resistance neglected in the existing models is considered in the present model. The present results are efficiently validated against measurements from published data to within 2% accuracy. Present predictions show that the single-diode model considering the shunt resistance gives accurate and reliable results. Also, aerosol optical depth (AOD) and air mass are most important atmospheric parameters having a significant impact on HCPV cell performance. In addition, the electrical efficiency (η) is noticed to increase with concentration to a certain concentration degree after which it decreases. Finally, based on the model predictions, let us conclude that the present model could be adapted properly to examine HCPV cells' performance over a broad range of operating conditions.

A point focusing double parabolic trough concentrator

Energy Technology Data Exchange (ETDEWEB)

Murphree, Quincy C. [Kentucky Mountain Bible College, Vancleve, KY (United States)

2001-07-01

This article shows that a point focusing solar concentrator can be made from two reflective parabolic troughs, a primary and a secondary, by orienting their longitudinal axes in perpendicular directions and separating them by the difference of their focal lengths along the optical axis. This offers a new alternative to the conventional 3-D paraboloidal concentrator permitting more flexibility in designs for applications requiring high concentrations. Both advantages and disadvantages are discussed. The intensity concentration ratio distribution is calculated in the focal plane and has elliptically shaped contours due to the inherent compensation of errant rays by the concave secondary. The ratio of the major to minor axes was 2.61 for the case considered, resulting in a concentration {approx}2.61 times that of a comparable concentrator without the compensation afforded by a concave secondary. Still, geometrical constraints limit the concentration to about 2000 suns for mirror quality errors of 5 mr. Optimisation of the compensation effect holds potential for improved performance for other concentrator designs. Finally, the functional dependence of the peak concentration and shading factor upon design parameters are presented. (Author)

Development of automatic high-concentration boron measurement technique; Konodo hoso jido sokutei gijutsu no kaihatsu

Energy Technology Data Exchange (ETDEWEB)

Maeda, T.; Honda, S.; Ito, A. [Kyushu Electric Power Co. Inc., Fukuoka (Japan)

1997-03-01

The technology that can automatically measure the boron concentration in boric acid water was developed. A high-concentration boric acid solution must be held at a high temperature to prevent the deposition. Skill and precision ({plus_minus}0.2 to 0.3% for 10 to 2500 ppm as boron concentration, and {plus_minus}2 to 3% for 2500 to 25,000 ppm) are required to analyze the boric acid solution manually. In theory, the boron concentration in a wide range can be measured, and boron has a constant-temperature function. A density hydrometer method that facilitates the treatment and calibration in high precision and at low cost was chosen. The vibration period generated when vibration is given to the solution specimen put in a U-tube is higher as the density is lower. On the basis of this theory, the density of a specimen can be obtained according to the relation with the same data of the known-concentration boric acid water. The high-concentration boric acid water that cannot be measured by the existing boron densitometer can be measured directly. It can also be measured in a low-concentration area. The technique can be used in a laboratory as the simplified method that is replaced by the current manual analysis. The reduction effect of analytical chemical`s waste liquid can also be expected. In the electric power industry, automated equipment is required for high efficiency and labor saving. 13 figs., 3 tabs.

Rennet-induced gelation of concentrated milk in the presence of sodium caseinate: differences between milk concentration using ultrafiltration and osmotic stressing.

Science.gov (United States)

Krishnankutty Nair, P; Corredig, M

2015-01-01

Concentrating milk is a common unit operation in the dairy industry. With the reduction of water, the particles interact more frequently with each other and the functionality of the casein micelles may depend on the interactions occurring during concentration. The objective of this research was to investigate the effect of concentration on the renneting properties of the casein micelles by comparing 2 concentration methods: ultrafiltration and osmotic stressing. Both methods selectively concentrate the protein fraction of milk, while the composition of the soluble phase is unaltered. To evaluate possible differences in the rearrangements of the casein micelles during concentration, renneting properties were evaluated with or without the addition of soluble caseins, added either before or after concentration. The results indicate that casein micelles undergo rearrangements during concentration and that shear during membrane filtration may play a role in affecting the final properties of the milk. Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

Melanin-concentrating hormone: from fish skin to skinny mammals.

Science.gov (United States)

Pissios, Pavlos; Maratos-Flier, Eleftheria

2003-07-01

In recent years, the key role of melanin-concentrating hormone (MCH) in regulating mammalian energy balance has been confirmed through several lines of evidence. When administered exogenously, MCH leads to a rapid and robust feeding response and chronic infusions result in the development of mild obesity. At the physiological level, it is known that MCH expression changes in states of altered energy balance, such as fasting and obesity. Genetic studies with mice have shown that ablation of either the gene for prepro-MCH or the gene encoding the MCH receptor leads to a lean phenotype. Finally, the administration of MCH antagonists appears to inhibit both feeding and the development of diet-induced obesity. The aim of this article is to review the recent data on MCH and MCH receptors in light of their emerging roles in energy homeostasis.

Developing the remote sensing-based early warning system for monitoring TSS concentrations in Lake Mead.

Science.gov (United States)

Imen, Sanaz; Chang, Ni-Bin; Yang, Y Jeffrey

2015-09-01

Adjustment of the water treatment process to changes in water quality is a focus area for engineers and managers of water treatment plants. The desired and preferred capability depends on timely and quantitative knowledge of water quality monitoring in terms of total suspended solids (TSS) concentrations. This paper presents the development of a suite of nowcasting and forecasting methods by using high-resolution remote-sensing-based monitoring techniques on a daily basis. First, the integrated data fusion and mining (IDFM) technique was applied to develop a near real-time monitoring system for daily nowcasting of the TSS concentrations. Then a nonlinear autoregressive neural network with external input (NARXNET) model was selected and applied for forecasting analysis of the changes in TSS concentrations over time on a rolling basis onward using the IDFM technique. The implementation of such an integrated forecasting and nowcasting approach was assessed by a case study at Lake Mead hosting the water intake for Las Vegas, Nevada, in the water-stressed western U.S. Long-term monthly averaged results showed no simultaneous impact from forest fire events on accelerating the rise of TSS concentration. However, the results showed a probable impact of a decade of drought on increasing TSS concentration in the Colorado River Arm and Overton Arm. Results of the forecasting model highlight the reservoir water level as a significant parameter in predicting TSS in Lake Mead. In addition, the R-squared value of 0.98 and the root mean square error of 0.5 between the observed and predicted TSS values demonstrates the reliability and application potential of this remote sensing-based early warning system in terms of TSS projections at a drinking water intake. Copyright © 2015 Elsevier Ltd. All rights reserved.

Degadation of semiconducting polymers by concentrated sunlight

DEFF Research Database (Denmark)

Tromholt, Thomas; Manceau, Matthieu; Petersen, Martin Helgesen

2011-01-01

infra-red spectra of MEH-PPV degraded at 1 sun intensity and at high solar concentration only showed minor deviations in degradation mechanisms. The acceleration factor was found to vary linearly with the solar concentration. Finally, a comparison of the degradation rates at 1 sun and 100 suns...... was carried out in a materials study employing five different conjugated polymers relevant to polymer solar cells for which acceleration factors in the range 19–55 were obtained.......A lens based sunlight concentration setup was used to accelerate the degradation of semiconducting polymers. Sunlight was collected outdoor and focused into an optical fiber bundle allowing for indoor experimental work. Photo-degradation of several polymers was studied by UV–vis absorbance...

Development of Zinc/Bromine Batteries for Load-Leveling Applications: Phase 2 Final Report

Energy Technology Data Exchange (ETDEWEB)

CLARK,NANCY H.; EIDLER,PHILLIP

1999-10-01

This report documents Phase 2 of a project to design, develop, and test a zinc/bromine battery technology for use in utility energy storage applications. The project was co-funded by the U.S. Department of Energy Office of Power Technologies through Sandia National Laboratories. The viability of the zinc/bromine technology was demonstrated in Phase 1. In Phase 2, the technology developed during Phase 1 was scaled up to a size appropriate for the application. Batteries were increased in size from 8-cell, 1170-cm{sup 2} cell stacks (Phase 1) to 8- and then 60-cell, 2500-cm{sup 2} cell stacks in this phase. The 2500-cm{sup 2} series battery stacks were developed as the building block for large utility battery systems. Core technology research on electrolyte and separator materials and on manufacturing techniques, which began in Phase 1, continued to be investigated during Phase 2. Finally, the end product of this project was a 100-kWh prototype battery system to be installed and tested at an electric utility.

Serum ferritin concentration in early pregnancy and risk of subsequent development of gestational diabetes: A prospective study

Directory of Open Access Journals (Sweden)

Sedigheh Soheilykhah

2017-08-01

Full Text Available Background: Elevated serum ferritin concentration is associated with insulin resistance and diabetes. Recently it has also been described in gestational diabetes mellitus (GDM. Objective: A prospective study was done to determine whether there was a relationship between serum ferritin concentration in early pregnancy and the risk of GDM. Materials and Methods: A study was performed on 1,384 pregnant women with gestational age of 12-16 weeks. A blood sample was obtained for measurement of ferritin in the first trimester. Diagnosis of GDM was done by 75 gr oral glucose tolerance test between 24-28 wk. Results: Women who developed GDM had a higher concentration of serum ferritin than women who did not develop GDM (p=0.01. A ferritin concentration of 45 ng/ml was calculated to be the 75th percentile for healthy pregnant women. Considering this level 32% in the GDM group and 25.2%of normal subjects exhibited high ferritin levels (p=0.01. The risk of GDM with these high levels of ferritin was 1.4-fold higher than that for subjects with lower concentrations. The Odds Ratio was 1.4 (95% CI= 1-1.87 (p=0.01. After adjusted for age Odds Ratio was 1.38 (95% CI=1.02-1.86 (p=0.03 and after adjustment for pre-pregnancy Body Mass index, the adjusted odds ratio was 1.31 (CI= 0.96-1.79 (p=0.08. After multivariable adjustment (age and body mass index, the adjusted odds ratio was 1.3 (0.95-1.8 (p=0.09. Conclusion: High serum ferritin can be regarded as a significant risk factor for the development of gestational diabetes.

Solution of non-steady-state substrate concentration in the action of biosensor response at mixed enzyme kinetics

Science.gov (United States)

Senthamarai, R.; Jana Ranjani, R.

2018-04-01

In this paper, a mathematical model of an amperometric biosensor at mixed enzyme kinetics and diffusion limitation in the case of substrate inhibition has been developed. The model is based on time dependent reaction diffusion equation containing a non -linear term related to non -Michaelis - Menten kinetics of the enzymatic reaction. Solution for the concentration of the substrate has been derived for all values of parameters using the homotopy perturbation method. All the approximate analytic expressions of substrate concentration are compared with simulation results using Scilab/Matlab program. Finally, we have given a satisfactory agreement between them.

Dental Age Estimation (DAE): Data management for tooth development stages including the third molar. Appropriate censoring of Stage H, the final stage of tooth development.

Science.gov (United States)

Roberts, Graham J; McDonald, Fraser; Andiappan, Manoharan; Lucas, Victoria S

2015-11-01

The final stage of dental development of third molars is usually helpful to indicate whether or not a subject is aged over 18 years. A complexity is that the final stage of development is unlimited in its upper border. Investigators usually select an inappropriate upper age limit or censor point for this tooth development stage. The literature was searched for appropriate data sets for dental age estimation and those that provided the count (n), the mean (x¯), and the standard deviation (sd) for each of the tooth development stages. The Demirjian G and Demirjian H were used for this study. Upper and lower limits of the Stage G and Stage H data were calculated limiting the data to plus or minus three standard deviations from the mean. The upper border of Stage H was limited by appropriate censoring at the maximum value for Stage G. The maximum age at attainment from published data, for Stage H, ranged from 22.60 years to 34.50 years. These data were explored to demonstrate how censoring provides an estimate for the correct maximum age for the final stage of Stage H as 21.64 years for UK Caucasians. This study shows that confining the data array of individual tooth developments stages to ± 3sd provides a reliable and logical way of censoring the data for tooth development stages with a Normal distribution of data. For Stage H this is inappropriate as it is unbounded in its upper limit. The use of a censored data array for Stage H using Percentile values is appropriate. This increases the reliability of using third molar Stage H alone to determine whether or not an individual is over 18 years old. For Stage H, individual ancestral groups should be censored using the same technique. Copyright © 2015 Elsevier Ltd and Faculty of Forensic and Legal Medicine. All rights reserved.

Flow line asymmetric nonimaging concentrating optics

Science.gov (United States)

Jiang, Lun; Winston, Roland

2016-09-01

Nonimaging Optics has shown that it achieves the theoretical limits by utilizing thermodynamic principles rather than conventional optics. Hence in this paper the condition of the "best" design are both defined and fulfilled in the framework of thermodynamic arguments, which we believe has profound consequences for the designs of thermal and even photovoltaic systems, even illumination and optical communication tasks. This new way of looking at the problem of efficient concentration depends on probabilities, geometric flux field and radiative heat transfer while "optics" in the conventional sense recedes into the background. Some of the new development of flow line designs will be introduced and the connection between the thermodynamics and flow line design will be officially formulated in the framework of geometric flux field. A new way of using geometric flux to design nonimaging optics will be introduced. And finally, we discuss the possibility of 3D ideal nonimaing optics.

The numerical benchmark CB2-S, final evaluation

International Nuclear Information System (INIS)

Chrapciak, V.

2002-01-01

In this paper are final results of numerical benchmark CB2-S compared (activity, gamma and neutron sources, concentration of important nuclides and decay heat). The participants are: Vladimir Chrapciak (SCALE), Ludmila Markova (SCALE), Svetlana Zabrodskaja (SCALA), Pavel Mikolas (WIMS). Eva Tinkova (HELIOS) and Maria Manolova (SCALE) (Authors)

Final Technical Progress Report: Development of Low-Cost Suspension Heliostat; December 7, 2011 - December 6, 2012

Energy Technology Data Exchange (ETDEWEB)

Bender, W.

2013-01-01

Final technical progress report of SunShot Incubator Solaflect Energy. The project succeeded in demonstrating that the Solaflect Suspension Heliostat design is viable for large-scale CSP installations. Canting accuracy is acceptable and is continually improving as Solaflect improves its understanding of this design. Cost reduction initiatives were successful, and there are still many opportunities for further development and further cost reduction.

Development status and operational features of the high temperature gas-cooled reactor. Final report

International Nuclear Information System (INIS)

Winkleblack, R.K.

1976-04-01

The objective of this study is to investigate the maturity of HTR-technology and to look out for possible technical problems, concerning introduction of large HTR power plants into the market. Further state and problems of introducing and closing the thorium fuel cycle is presented and judged. Finally, the state of development of advanced HTR-concepts for electricity production, the direct cycle HTR with helium turbine, and the gas-cooled fast breeder is discussed. In preparing the study, both HTR concepts with spherical and block-type fuel elements have been considered

Industrialisation et concentration urbaine

OpenAIRE

Kamal , Abdelhak

2010-01-01

The aim of this thesis is to analyze the determinants of the urban concentration and their effect at different levels of development. The empirical analysis focuses on the developing countries over the period 1950-2000 grouped by level of per capita income. The results confirm the existence of specific trajectories of urbanization rate and urban primacy which differs meaningfully according to the stage of development considered. Certain factors encourage urbanization and its concentration in ...

Effect of Roughage Source and Roughage to Concentrate Ratio on Animal Performance and Rumen Development in Veal Calves

NARCIS (Netherlands)

Suárez, B.J.; Reenen, van C.G.; Stockhofe, N.; Dijkstra, J.; Gerrits, W.J.J.

2007-01-01

Sixty-four male Holstein-Friesian x Dutch Friesian veal calves (46 ± 3.0 kg) were used to evaluate the effect of the inclusion of different levels and sources of dietary roughage on animal performance and rumen development. Treatments consisted of 1) C100 = concentrate only; 2) C70-S30 = concentrate

Development of a laundry waste treatment system

Energy Technology Data Exchange (ETDEWEB)

Kikuchi, M; Sugimoto, Y; Yusa, H; Ebara, K [Hitachi Ltd., Ibaraki (Japan). Hitachi Research Lab.; Takeshima, M [Hitachi Ltd., Ibaraki (Japan). Hitachi Works

1977-12-01

Fundamental and pilot plant experiments developed a laundry waste treatment system for nuclear power plants, consisting of a reverse osmosis unit for removal of radioactive materials and pre-concentration, and an evaporator for the final concentration. A sponge ball cleaning method was employed for the reverse osmosis unit and a heat-resistant antifoam reagent for the evaporator. The pilot plant test, using simulated wastes, showed a decontamination factor of above 10/sup 3/ and a volume reduction ratio of 10/sup -3/.

Entrainment at a sediment concentration interface in turbulent channel flow

Science.gov (United States)

Salinas, Jorge; Shringarpure, Mrugesh; Cantero, Mariano; Balachandar, S.

2016-11-01

In this work we address the role of turbulence on entrainment at a sediment concentration interface. This process can be conceived as the entrainment of sediment-free fluid into the bottom sediment-laden flow, or alternatively, as the entrainment of sediment into the top sediment-free flow. We have performed direct numerical simulations for fixed Reynolds and Schmidt numbers while varying the values of Richardson number and particle settling velocity. The analysis performed shows that the ability of the flow to pick up a given sediment size decreases with the distance from the bottom, and thus only fine enough sediment particles are entrained across the sediment concentration interface. For these cases, the concentration profiles evolve to a final steady state in good agreement with the well-known Rouse profile. The approach towards the Rouse profile happens through a transient self-similar state. Detailed analysis of the three dimensional structure of the sediment concentration interface shows the mechanisms by which sediment particles are lifted up by tongues of sediment-laden fluid with positive correlation between vertical velocity and sediment concentration. Finally, the mixing ability of the flow is addressed by monitoring the center of mass of the sediment-laden layer. With the support of ExxonMobil, NSF, ANPCyT, CONICET.

An international database of radionuclide concentration ratios for wildlife: development and uses.

Science.gov (United States)

Copplestone, D; Beresford, N A; Brown, J E; Yankovich, T

2013-12-01

A key element of most systems for assessing the impact of radionuclides on the environment is a means to estimate the transfer of radionuclides to organisms. To facilitate this, an international wildlife transfer database has been developed to provide an online, searchable compilation of transfer parameters in the form of equilibrium-based whole-organism to media concentration ratios. This paper describes the derivation of the wildlife transfer database, the key data sources it contains and highlights the applications for the data. Copyright © 2013 Elsevier Ltd. All rights reserved.

Mission related to regulation and development of the photovoltaic sector in France. Final report; Mission relative a la regulation et au developpement de la filiere photovoltaique en France. Rapport final

Energy Technology Data Exchange (ETDEWEB)

Charpin, J.M; Sine, A.; Helleisen, Ph.; Tlili, C. [Inspection Generale des Finances - IGF, 75 - Paris (France); Trink, C.; Stoffaes, Ch. [Conseil General de l' Industrie de l' Energie et des Technologies - CGIET, 75 - Paris (France)

2010-07-01

This report first gives an overview of the development of the photovoltaic stock in France (high potential with a middle term development constrained by high costs, consequences of a very strong increase of demands at the end of 2009, perspective of development at a rather high rate). Then, it outlines and discusses the financial consequences of such a high rate development, and the inadequacy between industrial objectives and development rate. It presents a development plan for this sector, stresses the need to implement new purchase obligation measures before the summer 2010, and to define a global action plan to be implemented at the beginning of 2011 for the development of photovoltaic electricity. Elements of international comparison are finally proposed

Development of Ultra-Efficient Electric Motors Final Technical Report Covering work from April 2002 through September 2007

International Nuclear Information System (INIS)

Rich Schiferl

2008-01-01

High temperature superconducting (HTS) motors offer the potential for dramatic volume and loss reduction compared to conventional, high horsepower, industrial motors. This report is the final report on the results of eight research tasks that address some of the issues related to HTS motor development that affect motor efficiency, cost, and reliability

Final processing vessel for radioactive waste

International Nuclear Information System (INIS)

Tejima, Takaya; Hiraki, Akimitsu.

1989-01-01

An inorganic inner layer comprising dense inorganic material such as organic polymer-impregnated concretes is formed to about 10 - 50 mm in average thickness at the inside of a metal vessel. Further, the surface of the vessel is formed as a flat surface with no or only small reinforcing protrusions. Thus, if the final processing vessel should be dropped during transportation or handling by mistake, since impact shocks do not concentrate to protrusions as usual, no local stress concentration occurs to the inorganic inner liner layer. Accordingly, the risk of rapture can be reduced greatly. Further, since impact shock resistance layer put between the metal vessel and the inorganic inner liner layer absorbs shocks, a further sufficient strength can be obtained against dropping accident. (T.M.)

Research to develop guidelines for cathodic protection of concentric neutral cables, volume 3

Science.gov (United States)

Hanck, J. A.; Nekoksa, G.

1982-08-01

Data associated with the corrosion of concentric neutral (CN) wires of direct buried primary cables were statistically analyzed, and guidelines for cathodic protection of CN wires for the electric utility industry were developed. The cathodic protection are reported. Field tests conducted at 36 bellholes excavated in California, Oklahoma, and North Carolina are described. Details of the electrochemical, chemical, bacteriological, and sieve analyses of native soil and imported backfill samples are also included.

Treatment and final storage of radioactive wastes from the nuclear fuel cycle

Energy Technology Data Exchange (ETDEWEB)

Krause, H [Kernforschungszentrum Karlsruhe (Germany, F.R.)

1977-05-01

Types, amounts and activity concentrations of the radioactive wastes arising from the different sections of the fuel cycle are described as well as the methods of their treatment and final disposal. By conversion to glass products, highly active fission product solutions can be transferred into a form well suited for final disposal. Low and medium level waste waters are purified so far that safe discharge or reuse is possible. The concentrates thus produced are incorporated into concrete or bitumen. Baling lends itself for treatment of non-combustible solid wastes. Combustible wastes can be incinerated, the residues are incorporated into concrete. For final storage of the conditioned wastes, salt formations in the deep underground are chosen in the Federal Republic of Germany. They offer a series of favourable preconditions for this purpose and guarantee the isolation of the radionuclides from the biocycle over secular periods of time.

Development of cost-effective surfactant flooding technology. Final report

Energy Technology Data Exchange (ETDEWEB)

Pope, G.A.; Sepehrnoori, K.

1996-11-01

Task 1 of this research was the development of a high-resolution, fully implicit, finite-difference, multiphase, multicomponent, compositional simulator for chemical flooding. The major physical phenomena modeled in this simulator are dispersion, heterogeneous permeability and porosity, adsorption, interfacial tension, relative permeability and capillary desaturation, compositional phase viscosity, compositional phase density and gravity effects, capillary pressure, and aqueous-oleic-microemulsion phase behavior. Polymer and its non-Newtonian rheology properties include shear-thinning viscosity, permeability reduction, inaccessible pore volume, and adsorption. Options of constant or variable space grids and time steps, constant-pressure or constant-rate well conditions, horizontal and vertical wells, and multiple slug injections are also available in the simulator. The solution scheme used in this simulator is fully implicit. The pressure equation and the mass-conservation equations are solved simultaneously for the aqueous-phase pressure and the total concentrations of each component. A third-order-in-space, second-order-in-time finite-difference method and a new total-variation-diminishing (TVD) third-order flux limiter are used that greatly reduce numerical dispersion effects. Task 2 was the optimization of surfactant flooding. The code UTCHEM was used to simulate surfactant polymer flooding.

Development of a criticality alarm system neutron detector: Final project report

International Nuclear Information System (INIS)

O'Dell, A.A.

1989-05-01

The primary objective of this project was to develop a prototype neutron detector for use in criticality alarm systems (CASs) at US Department of Energy (DOE) and contractor facilities wherever significant amounts of fissile material are processed or stored. Constraints placed on the design of the detector were that the overall size of the detector was to be as small as practical, the input voltage requirements were to be no more than 24 V, and that the gamma sensitivity would be as low as possible. Also, the detector should give dosimetric neutron response, and should have sufficient temporal capabilities to measure the entire range from fast (>1 ms) to slow (seconds to minutes) excursions, and sufficient dynamic range to measure from background to over 100 times background levels to insure proper activation of the Immediate Evacuation Alarm (IEA). Finally, the detector should insure rapid (<1 s) activation of the IEA in the event of a criticality excursion. 24 figs., 11 tabs

Comparison of the Force-, Velocity- and Power-Time Curves Between the Concentric-Only and Eccentric-Concentric Bench Press Exercises.

Science.gov (United States)

Pérez-Castilla, Alejandro; Comfort, Paul; McMahon, John J; Pestaña-Melero, Francisco Luis; García-Ramos, Amador

2018-01-17

The aim of this study was to compare the temporal and mechanical variables between the concentric-only and eccentric-concentric bench press (BP) variants. Twenty-one men (age: 22.0±4.2 years, body mass: 73.4±7.7 kg, height: 177.2±8.0 cm; one-repetition maximum [1RM]: 1.12±0.12 kg⋅kg) were evaluated during the concentric-only and eccentric-concentric BP variants using 80% 1RM. Temporal (concentric phase duration, propulsive phase duration, and time to reach the maximum values of force, velocity, and power) and mechanical variables (force, velocity, and power), determined using a linear velocity transducer, were compared between both BP variants. All temporal variables were significantly lower during the eccentric-concentric BP compared to the concentric-only BP (P velocity and power were significantly higher for the eccentric-concentric BP compared to the concentric-only BP (all P velocity (ES: 0.40) and power (ES: 0.41). The stretch-shortening cycle (i.e., eccentric-concentric BP) mainly enhanced force production at the early portion of the concentric phase, but this potentiation effect gradually reduced over the latter part of the movement. Finally, force was higher for the concentric-only BP during 49% of the concentric phase duration. These results suggest that both BP variants should be included during resistance training programs in order to optimize force output at different points of the concentric phase.

Final Technical Report: Development of an Abrasion-Resistant Antisoiling Coating for Front-Surface Reflectors

Energy Technology Data Exchange (ETDEWEB)

Gee, Randy C. [Sundog Solar Technology, Arvada, CO (United States)

2017-07-18

A high-performance reflective film has been successfully developed for Concentrating Solar Power (CSP) solar concentrators. Anti-soiling properties and abrasion resistance have been incorporated into the reflector to reduce reflector cleaning costs and to enhance durability. This approach has also resulted in higher reflectance and improved specularity. From the outset of this project we focused on the use of established high-volume roll-to-roll manufacturing techniques to achieve low manufacturing costs on a per ubit area basis. Roll-to-roll manufacturng equipment has a high capital cost so there is an entire industry devoted to roll-to-roll “toll” manufacturing, where the equipment is operated “around the clock” to produce a multitude of products for a large variety of uses. Using this approach, the reflective film can be manufactured by toll coaters/converters on an as-needed basis.

Development of a portable wireless system for bipolar concentric ECG recording

International Nuclear Information System (INIS)

Prats-Boluda, G; Ye-Lin, Y; Bueno Barrachina, J M; Senent, E; Rodriguez de Sanabria, R; Garcia-Casado, J

2015-01-01

Cardiovascular diseases (CVDs) remain the biggest cause of deaths worldwide. ECG monitoring is a key tool for early diagnosis of CVDs. Conventional monitors use monopolar electrodes resulting in poor spatial resolution surface recordings and requiring extensive wiring. High-spatial resolution surface electrocardiographic recordings provide valuable information for the diagnosis of a wide range of cardiac abnormalities, including infarction and arrhythmia. The aim of this work was to develop and test a wireless recording system for acquiring high spatial resolution ECG signals, based on a flexible tripolar concentric electrode (TCE) without cable wiring or external reference electrode which would make more comnfortable its use in clinical practice. For this, a portable, wireless sensor node for analogue conditioning, digitalization and transmission of a bipolar concentric ECG signal (BC-ECG) using a TCE and a Mason-likar Lead-I ECG (ML-Lead-I ECG) signal was developed. Experimental results from a total of 32 healthy volunteers showed that the ECG fiducial points in the BC-ECG signals, recorded with external and internal reference electrode, are consistent with those of simultaneous ML-Lead-I ECG. No statistically significant difference was found in either signal amplitude or morphology, regardless of the reference electrode used, being the signal-to-noise similar to that of ML-Lead-I ECG. Furthermore, it has been observed that BC-ECG signals contain information that could not available in conventional records, specially related to atria activity. The proposed wireless sensor node provides non-invasive high-local resolution ECG signals using only a TCE without additional wiring, which would have great potential in medical diagnosis of diseases such as atrial or ventricular fibrillations or arrhythmias that currently require invasive diagnostic procedures (catheterization). (paper)

Gastrointestinal development of dairy calves fed low- or high-starch concentrate at two milk allowances

DEFF Research Database (Denmark)

Kosiorowska, Anna Katarzyna; Puggaard, Liselotte; Hedemann, Mette Skou

2011-01-01

The objective was to study the effect of type of concentrate with varying starch and fibre content on growth and gastrointestinal development in preweaned dairy calves. Thirty-two newborn Danish Holstein male calves were allocated to four treatment groups in eight blocks of four calves. An experi...

Spacecraft fabrication and test MODIL. Final report

Energy Technology Data Exchange (ETDEWEB)

Saito, T.T.

1994-05-01

This report covers the period from October 1992 through the close of the project. FY 92 closed out with the successful briefing to industry and with many potential and important initiatives in the spacecraft arena. Due to the funding uncertainties, we were directed to proceed as if our funding would be approximately the same as FY 92 ($2M), but not to make any major new commitments. However, the MODIL`s FY 93 funding was reduced to $810K and we were directed to concentrate on the cryocooler area. The cryocooler effort completed its demonstration project. The final meetings with the cryocooler fabricators were very encouraging as we witnessed the enthusiastic reception of technology to help them reduce fabrication uncertainties. Support of the USAF Phillips Laboratory cryocooler program was continued including kick-off meetings for the Prototype Spacecraft Cryocooler (PSC). Under Phillips Laboratory support, Gill Cruz visited British Aerospace and Lucas Aerospace in the United Kingdom to assess their manufacturing capabilities. In the Automated Spacecraft & Assembly Project (ASAP), contracts were pursued for the analysis by four Brilliant Eyes prime contractors to provide a proprietary snap shot of their current status of Integrated Product Development. In the materials and structure thrust the final analysis was completed of the samples made under the contract (``Partial Automation of Matched Metal Net Shape Molding of Continuous Fiber Composites``) to SPARTA. The Precision Technologies thrust funded the Jet Propulsion Laboratory to prepare a plan to develop a Computer Aided Alignment capability to significantly reduce the time for alignment and even possibly provide real time and remote alignment capability of systems in flight.

Solar cell concentrating system

International Nuclear Information System (INIS)

Garg, H.P.; Sharma, V.K.; Agarwal, R.K.

1986-11-01

This study reviews fabrication techniques and testing facilities for different solar cells under concentration which have been developed and tested. It is also aimed to examine solar energy concentrators which are prospective candidates for photovoltaic concentrator systems. This may provide an impetus to the scientists working in the area of solar cell technology

Control of hydrogen concentration in reactor containment buildings by using passive catalytic recombiners

International Nuclear Information System (INIS)

Wolff, U.

1993-01-01

Severe accidents in nuclear power plants have the potential to generate hydrogen within the reactor containment building in concentrations likely to deflagrate or even detonate. This could endanger the containment integrity. Autocatalytic devices have been developed by the NIS company in Hanau, Germany, to control the hydrogen concentration within the containment. These devices have been tested by the Battelle Institute in Frankfurt, Germany, under conditions relevant to severe accidents. The catalytic device functions as required in a wide band of gas mixtures ranging from inerted conditions with low-hydrogen and/or low-oxygen concentrations up to detonable mixtures. The device starts up quickly, and has a high resistance against catalyst poisons including the effects of oil or cable fires. The device makes a strong contribution to gas mixing in the containment atmosphere. The paper summarizes the development work done and describes the final design of the device. Theoretical tools for analysis and prediction of catalyst performance in containment environments have been developed by the Battelle Institute and the Technical University of Munich. These tools have been verified and validated against experimental data. A phenomenological discussion of accident scenarios is used to explain the functional requirements for the autocatalytic devices in the control of hydrogen. Both the potential for and limitations of such devices for hydrogen control are discussed for large dry containments (PWRs) and for those which are originally inerted (BWRs)

Development of Soil Derived Concentration Guidance Levels for Decommissioning at Overseas Nuclear Power Plants

Energy Technology Data Exchange (ETDEWEB)

Sohn, Wook; Yoon, Suk Bon; Kim, Jeongju [KHNP CRI, Daejeon (Korea, Republic of)

2016-10-15

In Korea, the criteria are expected to be given in terms of dose as in US and Spain. However, since dose cannot be measured, corresponding measurable concentration limits, so-called Derived Concentration Guidance Levels (DCGLs), should be developed for each radionuclide which is expected to be present in the site. Also, as they serve as a goal of decommissioning and direct dismantling and decontamination methods applicable to the site, DCGLs should be developed in the early phase of decommissioning. This paper describes how each overseas nuclear power plant developed its site-specific Soil DCGLs: what kind of post closure use of the site (scenario) was assumed and how the site-specific Soil DCGLs were calculated based on the scenario assumed for each plant. Through this, it is intended to derive lessons learned which will be instructive for future decommissioning of domestic nuclear power plants including Kori Unit 1. It is very important to have as good under-standing as possible of characteristics of the site by collection of relevant information and data in order to apply a scenario which is most foreseeable and plausible for a site to be decommissioned and to provide site-specific inputs to the calculation of the Soil DCGLs. These efforts will help to have not-overly conservative values for the Soil DCGLs, thus thereby reducing the costs and time needed for performing the decommissioning.

Albendazole in environment: faecal concentrations in lambs and impact on lower development stages of helminths and seed germination.

Science.gov (United States)

Prchal, Lukáš; Podlipná, Radka; Lamka, Jiří; Dědková, Tereza; Skálová, Lenka; Vokřál, Ivan; Lecová, Lenka; Vaněk, Tomáš; Szotáková, Barbora

2016-07-01

Albendazole (ABZ), widely used benzimidazole anthelmintic, administered to animals enters via excrements into environment and may impact non-target organisms. Moreover, exposure of lower development stages of helminths to anthelmintics may also encourage the development of drug-resistant strains of helminths. In present project, the kinetics of ABZ (10 mg kg(-1) p.o.) and its metabolite (ABZ.SO, ABZSO2) elimination in faeces from treated Texel lambs were studied using UHPLC/MS/MS with the aim to find out their concentrations achievable in the environment. Consequently, the effect of these compounds on lower development stages of Barber's pole worm (Haemonchus contortus) and on germination of white mustard (Sinapis alba) seeds was evaluated. The results showed that ABZ concentrations in faeces excreted in 4-60 h after treatment were above the concentrations lethal for H. contortus eggs. Moreover, pre-incubation with sub-lethal doses of ABZ and ABZ.SO did not increase the resistance of H. contortus eggs and larvae to anthelmintics. On the other hand, concentrations of ABZ and ABZ.SO in faeces are so high that might have negative influence on non-target soil invertebrates. As neither ABZ nor its metabolites affect the germination of mustard seeds, phytoremediation could be considered as potential tool for detoxification of ABZ in the environment.

Data on final calcium concentration in native gel reagents determined accurately through inductively coupled plasma measurements

Directory of Open Access Journals (Sweden)

Jeffrey Viviano

2016-03-01

Full Text Available In this article we present data on the concentration of calcium as determined by Inductively Coupled Plasma (ICP measurements. Calcium was estimated in the reagents used for native gel electrophoresis of Neuronal Calcium Sensor (NCS proteins. NCS proteins exhibit calcium-dependent mobility shift in native gels. The sensitivity of this shift to calcium necessitated a precise determination of calcium concentrations in all reagents used. We determined the calcium concentrations in different components used along with the samples in the native gel experiments. These were: 20 mM Tris pH 7.5, loading dye and running buffer, with distilled water as reference. Calcium determinations were through ICP measurements. It was found that the running buffer contained calcium (244 nM over the blank. Keywords: Neuronal calcium sensor proteins, Electrophoresis, Mobility shift, Calcium, Magnesium

Concentration of solar radiation by white backed photovoltaic panels.

Science.gov (United States)

Smestad, G; Hamill, P

1984-12-01

In this paper, we present an analysis of the concentration achieved by white backed photovoltaic panels. Concentration is due to the trapping by light scattered in the refractive plate to which the solar cell is bonded. Using the reciprocity relation and assuming the ideal case of a Lambertian distribution, a detailed model is formulated that includes the effects of the thickness and walls of the concentrator. This model converges to the thermodynamic limit and is found to be consistent with experimental results for a wide range of cell sizes. Finally, the model is generalized to multiple-cell photovoltaic panels.

Concentrating Solar Power Central Receiver Panel Component Fabrication and Testing FINAL REPORT

Energy Technology Data Exchange (ETDEWEB)

McDowell, Michael W [Pratt & Whitney Rocketdyne; Miner, Kris [Pratt & Whitney Rocketdyne

2013-03-30

test scale prototype receiver, off sun but at temperature, at a molten salt loop at ground level adjacent to the tower also had to be abandoned. Thus, no test facility existed for a molten salt receiver test. As a result, PWR completed the prototype receiver design and then fabricated key components for testing instead of fabricating the complete prototype receiver. A number of innovative design ideas have been developed. Key features of the receiver panel have been identified. This evaluation includes input from Solar 2, personal experience of people working on these programs and meetings with Sandia. Key components of the receiver design and key processes used to fabricate a receiver have been selected for further evaluation. The Test Plan, Concentrated Solar Power Receiver In Cooperation with the Department of Energy and Sandia National Laboratory was written to define the scope of the testing to be completed as well as to provide details related to the hardware, instrumentation, and data acquisition. The document contains a list of test objectives, a test matrix, and an associated test box showing the operating points to be tested. Test Objectives: 1. Demonstrate low-cost manufacturability 2. Demonstrate robustness of two different tube base materials 3. Collect temperature data during on sun operation 4. Demonstrate long term repeated daily operation of heat shields 5. Complete pinhole tube weld repairs 6. Anchor thermal models This report discusses the tests performed, the results, and implications for design improvements and LCOE reduction.

Uncertainty budget for final assay of a pharmaceutical product based on RP-HPLC

DEFF Research Database (Denmark)

Heydorn, Kaj; Anglov, Thomas; Byrialsen, Kirsten

2003-01-01

). The reported example illustrates the estimation of uncertainty for the final determination of a protein concentration by HPLC using UV detection, using the approach described by EURACHEM/CITAC. The combined standard uncertainty for a protein concentration of 2400 mumol/L was estimated to be 14 mumol/L. All...

Tracking instrument and control for solar concentrators. Final technical report, October 1979-January 1981

Energy Technology Data Exchange (ETDEWEB)

Gray, J; Kuhlman, J

1981-01-31

The tracker uses a single photo sensor, and a rotating aperature to obtain tracking accuracies better than 1.5 mrads (0.1 degs). Peak signal detection is used to eliminate tracking of false sources, i.e., clouds, etc. A prism is employed to obtain an extended field of view (150 degs axially - 360 degs radially). The tracker digitally measures the Suns displacement angle relative to the concentrator axis, and repositions it incrementally. This arrangement permits the use of low cost non-servo motors. The local controller contains microprocessor based electronics, incorporating digital signal processing. A single controller may be time shared by a maximum of sixteen trackers, providing a high performance, cost effective solar tracking system, suitable for both line and point focus concentrators. An installation may have the local controller programmed as a standalone unit or slaved to a central controller. When used with a central controller, dynamic data monitoring and logging is available, together with the ability to change system modes and parameters, as desired.

Platelet concentrates: reducing the risk of transfusion-transmitted bacterial infections

Directory of Open Access Journals (Sweden)

de Korte D

2014-06-01

Full Text Available Dirk de Korte,1 Jan H Marcelis2 1Department of Product and Process Development, Sanquin Blood Bank, Amsterdam, 2Department of Microbiology, St Elisabeth Hospital, Tilburg, the Netherlands Abstract: The introduction of a combination of interventions during collection of whole-blood or platelet concentrates has been successful in lowering the degree of bacterial contamination in the final product, the platelet concentrate, by 50%–75%. These interventions were improved donor questionnaires, best-practice skin disinfection, and diversion of first blood volume. These interventions have reduced the number of bacteria present in the platelet concentrates. In combination with screening for bacterial contamination of platelet concentrates with a culture method, the degree of transfusion-transmitted bacterial infection has been reduced significantly. Due to the very low initial bacteria counts upon collection of the products, the need for improved sensitivity of early screenings tests or highly selective point-of-issue tests remains. The latter should be rapid and easy to perform. An alternative approach might be the implementation of pathogen-inactivation methods for cellular blood products to reduce the amount of pathogens. However, these methods are costly, and so far not proved to be cost-effective, especially in countries with an already-low incidence of transfusion-transmitted infections by viruses, parasites, or bacteria. Keywords: blood products, bacterial contamination, screening, point of issue, pathogen inactivation

Thermophotovoltaic (TPV) technology development. Final report, May 15, 1995--December 1, 1995

International Nuclear Information System (INIS)

1995-01-01

This program information release (PIR) summarizes work performed under Task Order Contract SF17787, Task Order 18: Thermophotovoltaic Technology Development, sponsored by the U.S. Department of Energy. The period of performance was 15 May 1995 to 1 December 1995. Under this task order, a system model for a thermophotovoltaic (MV) converter was implemented and used to compare a conceptual design for an advanced quaternary III-V cell with integral filter with results previously published for a binary GaSb cell with a freestanding filter. Model results were used to assess the merits of TPV conversion for meeting various levels of space power requirements, including low to medium power isotope applications and high-power reactor applications. A TPV cell development program was initiated to determine the feasibility of fabricating quaternary III-V cells by molecular beam epitaxy. Lastly, a conceptual design was completed for a low-cost demonstration system to test the performance of TPV converters at a multi-cell, sub-system level. The results of these efforts are reported briefly in an executive summary, then in somewhat more detail as a final briefing section in which charts have been reproduced. Additional technical detail is provided in the appendices

Leadership Development Program Final Project

Science.gov (United States)

Parrish, Teresa C.

2016-01-01

TOSC is NASA's prime contractor tasked to successfully assemble, test, and launch the EM1 spacecraft. TOSC success is highly dependent on design products from the other NASA Programs manufacturing and delivering the flight hardware; Space Launch System(SLS) and Multi-Purpose Crew Vehicle(MPCV). Design products directly feed into TOSC's: Procedures, Personnel training, Hardware assembly, Software development, Integrated vehicle test and checkout, Launch. TOSC senior management recognized a significant schedule risk as these products are still being developed by the other two (2) programs; SVE and ACE positions were created.

Telephone Flat Geothermal Development Project Environmental Impact Statement Environmental Impact Report. Final

Energy Technology Data Exchange (ETDEWEB)

None

1999-02-01

This Final Environmental Impact Statement and Environmental Impact Report (Final EIS/EIR) has been prepared to meet the requirements of the National Environmental Policy Act (NEPA) and the California Environmental Quality Act (CEQA). The Proposed Action includes the construction, operation, and decommissioning of a 48 megawatt (gross) geothermal power plant with ancillary facilities (10-12 production well pads and 3-5 injection well pads, production and injection pipelines), access roads, and a 230-kilovolt (kV) transmission line in the Modoc National Forest in Siskiyou County, California. Alternative locations for the power plant site within a reasonable distance of the middle of the wellfield were determined to be technically feasible. Three power plant site alternatives are evaluated in the Final EIS/EIR.

Development of a treatment process for the removal of heavy metals from raw water for drinking water supply using chelating ion exchange resins. Subproject 1. Final report; Entwicklung der Verfahrenstechnik zur Eliminierung von Schwermetallen aus Rohwaessern zur Trinkwassergewinnung mit chelatbildenden Kationenaustauscherharzen zur technischen Reife. Teilprojekt 1. Abschlussbericht

Energy Technology Data Exchange (ETDEWEB)

Overath, H.; Stetter, D.; Doerdelmann, O.

2002-07-01

Chelating cation exchange resins with iminodiacetic acid group (Lewatit TP 207 and Amberlite IRC 748) were tested for the removal of heavy metals in a drinking water treatment plant. The pilot scale filtration experiments were conducted by varying the operating conditions, such as flow rate and feed concentrations. Heavy metal concentrations (nickel, lead, cadmium, zinc) in the feed were adjusted between 20 and 200 {mu}g/L. Different methods for regeneration and conditioning of the resins were developed and investigated. Finally the ion exchange resins were tested according to German health regulations for ion exchangers in drinking water treatment. (orig.)

Effects of Supplementing Concentrates Differing in Carbohydrate Composition in Veal Calf Diets: II. Rumen Development

NARCIS (Netherlands)

Suárez, B.J.; Reenen, van C.G.; Gerrits, W.J.J.; Stockhofe, N.; Vuuren, van A.M.; Dijkstra, J.

2006-01-01

The objective of this experiment was to examine the effects of concentrates in feed, differing in carbohydrate source, on the rumen development of veal calves. For this purpose, 160 male Holstein Friesian x Dutch Friesian crossbred calves were used in a complete randomized block design with a 5 x 2

Development of a thermionic magnicon amplifier at 11.4 GHz. Final report for period May 16, 1995 - May 15, 2001

International Nuclear Information System (INIS)

Gold, Steven H.; Fliflet, Arne W.

2001-01-01

This is the final report on the research program ''Development of a Thermionic Magnicon Amplifier at 11.4 GHz,'' which was carried out by the Plasma Physics Division of the Naval Research Laboratory. Its goal was to develop a high-power, frequency-doubling X-band magnicon amplifier, an advanced scanning-beam amplifier, for use in future linear colliders. The final design parameters were 61 MW at 11.424 GHz, 59 dB gain, 59% efficiency, 1 microsecond pulselength and 10 Hz repetition rate. At the conclusion of this program, the magnicon was undergoing high-power conditioning, having already demonstrated high-power operation, phase stability, a linear drive curve, a small operational frequency bandwidth and a spectrally pure, single-mode output

Development and On-Field Testing of Low-Cost Portable System for Monitoring PM2.5 Concentrations.

Science.gov (United States)

N Genikomsakis, Konstantinos; Galatoulas, Nikolaos-Fivos; I Dallas, Panagiotis; Candanedo Ibarra, Luis Miguel; Margaritis, Dimitris; S Ioakimidis, Christos

2018-04-01

Recent developments in the field of low-cost sensors enable the design and implementation of compact, inexpensive and portable sensing units for air pollution monitoring with fine-detailed spatial and temporal resolution, in order to support applications of wider interest in the area of intelligent transportation systems (ITS). In this context, the present work advances the concept of developing a low-cost portable air pollution monitoring system (APMS) for measuring the concentrations of particulate matter (PM), in particular fine particles with a diameter of 2.5 μm or less (PM2.5). Specifically, this paper presents the on-field testing of the proposed low-cost APMS implementation using roadside measurements from a mobile laboratory equipped with a calibrated instrument as the basis of comparison and showcases its accuracy on characterizing the PM2.5 concentrations on 1 min resolution in an on-road trial. Moreover, it demonstrates the intended application of collecting fine-grained spatio-temporal PM2.5 profiles by mounting the developed APMS on an electric bike as a case study in the city of Mons, Belgium.

21 CFR 184.1979c - Whey protein concentrate.

Science.gov (United States)

2010-04-01

... the methods prescribed in section 16.057 (liquid sample), entitled “Gravimetric Method—Official Final... concentrate, on a dry product basis, based on analytical methods in the referenced sections of “Official Methods of Analysis of the Association of Official Analytical Chemists,” 13th ed. (1980), which is...

36 CFR 902.61 - Final determination.

Science.gov (United States)

2010-07-01

... 36 Parks, Forests, and Public Property 3 2010-07-01 2010-07-01 false Final determination. 902.61 Section 902.61 Parks, Forests, and Public Property PENNSYLVANIA AVENUE DEVELOPMENT CORPORATION FREEDOM OF INFORMATION ACT Time Limitations § 902.61 Final determination. A determination with respect to any appeal made...

Development of the SEAtrace{trademark} barrier verification and validation technology. Final report

Energy Technology Data Exchange (ETDEWEB)

Dunn, S.D.; Lowry, W.; Walsh, R.; Rao, D.V. [Science and Engineering Associates, Santa Fe, NM (United States); Williams, C. [Sandia National Labs., Albuquerque, NM (United States). Underground Storage Technology Dept.

1998-08-01

In-situ barrier emplacement techniques and materials for the containment of high-risk contaminants in soils are currently being developed by the Department of Energy (DOE). Because of their relatively high cost, the barriers are intended to be used in cases where the risk is too great to remove the contaminants, the contaminants are too difficult to remove with current technologies, or the potential movement of the contaminants to the water table is so high that immediate action needs to be taken to reduce health risks. Assessing the integrity of the barrier once it is emplaced, and during its anticipated life, is a very difficult but necessary requirement. Science and Engineering Associates, Inc., (SEA) and Sandia National Laboratories (SNL) have developed a quantitative subsurface barrier assessment system using gaseous tracers in support of the Subsurface Contaminants Focus Area barrier technology program. Called SEAtrace{trademark}, this system integrates an autonomous, multi-point soil vapor sampling and analysis system with a global optimization modeling methodology to locate and size barrier breaches in real time. The methodology for the global optimization code was completed and a prototype code written using simplifying assumptions. Preliminary modeling work to validate the code assumptions were performed using the T2VOC numerical code. A multi-point field sampling system was built to take soil gas samples and analyze for tracer gas concentration. The tracer concentration histories were used in the global optimization code to locate and size barrier breaches. SEAtrace{trademark} was consistently able to detect and locate leaks, even under very adverse conditions. The system was able to locate the leak to within 0.75 m of the actual value, and was able to determine the size of the leak to within 0.15 m.

Development of the SEAtrace trademark barrier verification and validation technology. Final report

International Nuclear Information System (INIS)

Dunn, S.D.; Lowry, W.; Walsh, R.; Rao, D.V.; Williams, C.

1998-08-01

In-situ barrier emplacement techniques and materials for the containment of high-risk contaminants in soils are currently being developed by the Department of Energy (DOE). Because of their relatively high cost, the barriers are intended to be used in cases where the risk is too great to remove the contaminants, the contaminants are too difficult to remove with current technologies, or the potential movement of the contaminants to the water table is so high that immediate action needs to be taken to reduce health risks. Assessing the integrity of the barrier once it is emplaced, and during its anticipated life, is a very difficult but necessary requirement. Science and Engineering Associates, Inc., (SEA) and Sandia National Laboratories (SNL) have developed a quantitative subsurface barrier assessment system using gaseous tracers in support of the Subsurface Contaminants Focus Area barrier technology program. Called SEAtrace trademark, this system integrates an autonomous, multi-point soil vapor sampling and analysis system with a global optimization modeling methodology to locate and size barrier breaches in real time. The methodology for the global optimization code was completed and a prototype code written using simplifying assumptions. Preliminary modeling work to validate the code assumptions were performed using the T2VOC numerical code. A multi-point field sampling system was built to take soil gas samples and analyze for tracer gas concentration. The tracer concentration histories were used in the global optimization code to locate and size barrier breaches. SEAtrace trademark was consistently able to detect and locate leaks, even under very adverse conditions. The system was able to locate the leak to within 0.75 m of the actual value, and was able to determine the size of the leak to within 0.15 m

Uranium development in the San Juan Basin region: a report on environmental issues. Final edition

International Nuclear Information System (INIS)

1980-01-01

The goal of this study is to provide a regional analysis of the effect of uranium development on the human and natural environment of northwest New Mexico from the present until the year 2000. This report contains comments on the published draft of this study from representatives of federal and state agencies, public interest groups, local governments, leading citizens, and the uranium industry. Many of the comments led to substantial changes in the text and were carefully considered in the final edition of the study

Develop generic equations to determine radon daughters concentrations in air

International Nuclear Information System (INIS)

Shweikani, R.; Jerby, B.

2011-06-01

Measurements of radon daughter concentrations in air are very important to determine the human dose from background radiation. Therefore, many studies tried to find measurements methods depending on many specific parameters such as measurement time, air pumping period and sample volume. In this study a general equations to determine radon daughter's concentrations in air was found using direct samples. The Equations results were closed to the results obtained from other well known methods. Many measurements with different places and various conditions were performed; the results showed that the new equations are able to be used with an error less than 10%, The relative error can be reduced by increasing the pumping rate or measuring high concentration cases.(author)

NTRCI Legacy Engine Research and Development Project Final Technical Report

Energy Technology Data Exchange (ETDEWEB)

Smith-Holbert, Connie [National Transportation Research Center, Inc., Knoxville, TN (United States); Petrolino, Joseph [National Transportation Research Center, Inc., Knoxville, TN (United States); Watkins, Bart [Power Source Technologies Inc., Corvallis, OR (United States); Irick, David [Power Source Technologies Inc., Corvallis, OR (United States)

2011-12-31

The Legacy engine is a completely new design, transitional diesel engine, replacing the reciprocating engine with a rotary engine. The Legacy engine offers significant advances over conventional internal combustion engines in 1) power to weight ratio; 2) multiple fuel acceptance; 3) fuel economy; and 4) environmental compliance. These advances are achieved through a combination of innovative design geometry, rotary motion, aspiration simplicity, and manufacturing/part simplicity. The key technical challenge to the Legacy engine's commercialization, and the focus of this project, was the development of a viable roton tip seal. The PST concept for the roton tip seal was developed into a manufacturable design. The design was evaluated using a custom designed and fabricated seal test fixture and further refined. This design was incorporated into the GEN2.5A prototype and tested for achievable compression pressure. The Decision Point at the end of Phase 1 of the project (described below) was to further optimize the existing tip seal design. Enhancements to the tip seal design were incorporated into the GEN2.5B prototype and tested and evaluated using the iterative research strategy described below. Compression pressures adequate for compression ignition of diesel fuel were achieved, although not consistently in all combustion volumes. The variation in compression pressures was characterized versus design features. As the roton tip seal performance was improved, results pointed toward inadequate performance of the housing side seals. Enhancement of the housing side seal system was accomplished using a custom designed side seal test fixture. The design enhancements developed with the test fixture were also incorporated into the GEN2.5B prototype and tested and evaluated using the iterative research strategy described below. Finally, to simplify the requirements for the roton tip seals and to enhance the introduction and combustion of fuel, a flush-mount fuel injector

Micro solar concentrators: Design and fabrication for microcells arrays

Science.gov (United States)

Jutteau, Sébastien; Paire, Myriam; Proise, Florian; Lombez, Laurent; Guillemoles, Jean-François

2015-09-01

In this work we look at a micro-concentrating system adapted to a new type of concentrator photovoltaic material, well known for flate-plate applications, Cu(In,Ga)Se2. Cu(In,Ga)Se2 solar cells are polycrystalline thin film devices that can be deposited by a variety of techniques. We proposed to use a microcell architecture [1], [2], with lateral dimensions varying from a few μm to hundreds of μm, to adapt the film cell to concentration conditions. A 5% absolute efficiency increase on Cu(In,Ga)Se2 microcells at 475 suns has been observed for a final efficiency of 21.3%[3]. We study micro-concentrating systems adapted to the low and middle concentration range, where thin film concentrator cells will lean to substrate fabrication simplification and cost savings. Our study includes optical design, fabrication and experimental tests of prototypes.

Separation, Concentration, and Immobilization of Technetium and Iodine from Alkaline Supernate Waste

Energy Technology Data Exchange (ETDEWEB)

James Harvey; Michael Gula

1998-12-07

Development of remediation technologies for the characterization, retrieval, treatment, concentration, and final disposal of radioactive and chemical tank waste stored within the Department of Energy (DOE) complex represents an enormous scientific and technological challenge. A combined total of over 90 million gallons of high-level waste (HLW) and low-level waste (LLW) are stored in 335 underground storage tanks at four different DOE sites. Roughly 98% of this waste is highly alkaline in nature and contains high concentrations of nitrate and nitrite salts along with lesser concentrations of other salts. The primary waste forms are sludge, saltcake, and liquid supernatant with the bulk of the radioactivity contained in the sludge, making it the largest source of HLW. The saltcake (liquid waste with most of the water removed) and liquid supernatant consist mainly of sodium nitrate and sodium hydroxide salts. The main radioactive constituent in the alkaline supernatant is cesium-137, but strontium-90, technetium-99, and transuranic nuclides are also present in varying concentrations. Reduction of the radioactivity below Nuclear Regulatory Commission (NRC) limits would allow the bulk of the waste to be disposed of as LLW. Because of the long half-life of technetium-99 (2.1 x 10 5 y) and the mobility of the pertechnetate ion (TcO 4 - ) in the environment, it is expected that technetium will have to be removed from the Hanford wastes prior to disposal as LLW. Also, for some of the wastes, some level of technetium removal will be required to meet LLW criteria for radioactive content. Therefore, DOE has identified a need to develop technologies for the separation and concentration of technetium-99 from LLW streams. Eichrom has responded to this DOE-identified need by demonstrating a complete flowsheet for the separation, concentration, and immobilization of technetium (and iodine) from alkaline supernatant waste.

Final Treatment Center Project for Liquid and Wet Radioactive Waste in Slovakia

International Nuclear Information System (INIS)

Kravarik, K.; Stubna, M.; Pekar, A.; Krajc, T.; Zatkulak, M.; Holicka, Z.; Slezak, M.

2006-01-01

The Final Treatment Center (FTC) for Mochovce nuclear power plant (NPP) is designed for treatment and final conditioning of radioactive liquid and wet waste produced from plant operation. Mochovce NNP uses a Russian VVER-440 type reactor. Treated wastes comprise radioactive concentrates, spent resin and sludge. VUJE Inc. as an experienced company in field of treatment of radioactive waste in Slovakia has been chosen as main contractor for technological part of FTC. This paper describes the capacity, flow chart, overall waste flow and parameters of the main components in the FTC. The initial project was submitted for approval to the Slovak Electric plc. in 2003. The design and manufacture of main components were performed in 2004 and 2005. FTC construction work started early in 2004. Initial non-radioactive testing of the system is planned for summer 2006 and then radioactive tests are to be followed. A one-year trial operation of facility is planned for completion in 2007. SE - VYZ will be operates the FTC during trial operation and after its completion. SE - VYZ is subsidiary company of Slovak Electric plc. and it is responsible for treatment with radioactive waste and spent fuel in the Slovak republic. SE - VYZ has, besides of other significant experience with operation of Jaslovske Bohunice Treatment Centre. The overall capacity of the FTC is 870 m 3 /year of concentrates and 40 m 3 /year of spent resin and sludge. Bituminization and cementation were provided as main technologies for treatment of these wastes. Treatment of concentrate is performed by bituminization. Concentrate and bitumen are metered into a thin film evaporator with rotating wiping blades. Surplus water is evaporated and concentrate salts are embedded in bitumen. Bitumen product is discharged into 200 l steel drums. Spent resin and sludge are decanted, dried and mixed with bitumen. These mixtures are also discharged into 200 l steel drums. Drums are moved along bituminization line on a roller

Thoracic and Cardiovascular Surgeons’ Perception of the Concentration of Cardiovascular Operations in Seoul Metropolitan Area’s Hospitals

Directory of Open Access Journals (Sweden)

Hyo Seon Jeong

2016-12-01

Full Text Available Background: The purpose of this study is to evaluate the concentration of cardiovascular surgical procedures in a metropolitan area and investigate the perception of specialists regarding governmental policies to resolve this imbalance. Methods: From March to May 2015, surveys were distributed to members of the Thoracic and Cardiovascular Surgery Association. The final pool of research subjects consisted of 75 respondents. Subjects were queried regarding the concentration of cardiovascular operations in metropolitan areas, alternatives to the imbalance, and governmental policies to resolve the inequalities. Results: Survey participants responded that South Korea needs governmental policies to alleviate the concentration of cardiovascular surgery patients in large metropolitan hospitals. Participants agreed that the freedom to choose medical institutions and improved accessibility to metropolitan hospitals due to advanced transportation systems were some of the causes for the concentration. A majority (98.7% of respondents thought establishing thoracic and cardiovascular surgery centers in provinces was an appropriate solution to alleviate the concentration. Thoracic and cardiovascular surgery specialists were ranked as the number one group on which to focus development. Conclusion: Developing and carrying out policies to establish thoracic and cardiovascular surgery centers in provinces will alleviate the regional imbalance in available heart surgery services and an overall improvement in cardiovascular disease treatment in South Korea.

PM2.5 mitigation in China: Socioeconomic determinants of concentrations and differential control policies.

Science.gov (United States)

Luo, Kui; Li, Guangdong; Fang, Chuanglin; Sun, Siao

2018-05-01

Elucidating the key impact factors on PM 2.5 concentrations is crucial to formulate effective mitigation policies. In this study, we employed an extended Stochastic Impacts by Regression on Population Affluence and Technology (STIRPAT) model to identify the socioeconomic determinants of PM 2.5 concentrations for 12 different regions and across China. The evaluation was based on a balanced panel dataset integrating long-term satellite-derived PM 2.5 concentrations and socio-economic data in China from 1999 to 2011. Empirical results indicate that the influencing factors can be ranked in descending order of importance as: proportion of secondary sector of the economy, GDP per capita, urbanization, population, energy intensity, and proportion of tertiary sector. Proportion of secondary sector is the greatest contribution to increasing PM 2.5 concentrations, especially for heavily polluted regions. GDP per capita is secondary in importance, and its impact is weakened by the existence of an EKC relationship between GDP per capita and PM 2.5 concentrations. Therefore, PM 2.5 pollution is an economic development mode problem, rather than a general economic development problem. The impact of urbanization varies across regions; while promoting urbanization will be conducive to decreased PM 2.5 concentrations in Northwest China and Northeast China, it will contribute to increased PM 2.5 concentrations in other regions. Population and energy intensity are significant in most regions, but neither are decisive factors because of the small absolute value of their coefficients. Finally, different combinations of mitigation policies are proposed for different regions in this study to meet the mitigation targets. Copyright © 2018 Elsevier Ltd. All rights reserved.

Development of a downhole tool measuring real-time concentration of ionic tracers and pH in geothermal reservoirs

Science.gov (United States)

Hess, Ryan F.; Boyle, Timothy J.; Limmer, Steven; Yelton, William G.; Bingham, Samuel; Stillman, Greg; Lindblom, Scott; Cieslewski, Grzegorz

2014-06-01

For enhanced or Engineered Geothermal Systems (EGS) geothermal brine is pumped to the surface via the production wells, the heat extracted to turn a turbine to generate electricity, and the spent brine re-injected via injection wells back underground. If designed properly, the subsurface rock formations will lead this water back to the extraction well as heated brine. Proper monitoring of these geothermal reservoirs is essential for developing and maintaining the necessary level of productivity of the field. Chemical tracers are commonly used to characterize the fracture network and determine the connectivity between the injection and production wells. Currently, most tracer experiments involve injecting the tracer at the injection well, manually collecting liquid samples at the wellhead of the production well, and sending the samples off for laboratory analysis. While this method provides accurate tracer concentration data at very low levels of detection, it does not provide information regarding the location of the fractures which were conducting the tracer between wellbores. Sandia is developing a high-temperature electrochemical sensor capable of measuring tracer concentrations and pH downhole on a wireline tool. The goal of this effort is to collect real-time pH and ionic tracer concentration data at temperatures up to 225 °C and pressures up to 3000 psi. In this paper, a prototype electrochemical sensor and the initial data obtained will be presented detailing the measurement of iodide tracer concentrations at high temperature and pressure in a newly developed laboratory scale autoclave.

Development of Indoor Air Pollution Concentration Prediction by Geospatial Analysis

Directory of Open Access Journals (Sweden)

Adyati Pradini Yudison

2015-07-01

Full Text Available People living near busy roads are potentially exposed to traffic-induced air pollutants. The pollutants may intrude into the indoor environment, causing health risks to the occupants. Prediction of pollutant exposure therefore is of great importance for impact assessment and policy making related to environmentally sustainable transport. This study involved the selection of spatial interpolation methods that can be used for prediction of indoor air quality based on outdoor pollutant mapping without indoor measurement data. The research was undertaken in the densely populated area of Karees, Bandung, Indonesia. The air pollutant NO2 was monitored in this area as a preliminary study. Nitrogen dioxide concentrations were measured by passive diffusion tube. Outdoor NO2 concentrations were measured at 94 locations, consisting of 30 roadside and 64 outdoor locations. Residential indoor NO2 concentrations were measured at 64 locations. To obtain a spatially continuous air quality map, the spatial interpolation methods of inverse distance weighting (IDW and Kriging were applied. Selection of interpolation method was done based on the smallest root mean square error (RMSE and standard deviation (SD. The most appropriate interpolation method for outdoor NO2 concentration mapping was Kriging with an SD value of 5.45 µg/m3 and an RMSE value of 5.45 µg/m3, while for indoor NO2 concentration mapping the IDW was best fitted with an RMSE value of 5.92 µg/m3 and an SD value of 5.92 µg/m3.

Alteration in peripheral blood concentration of certain pro-inflammatory cytokines in cows developing retention of fetal membranes.

Science.gov (United States)

Boro, Prasanta; Kumaresan, A; Pathak, Rupal; Patbandha, T K; Kumari, Susavi; Yadav, Asha; Manimaran, A; Baithalu, R K; Attupuram, Nitin M; Mohanty, T K

2015-06-01

Retention of fetal membranes (RFM) adversely affects the production and reproduction potential of the affected cows leading to huge economic loss. Physiological separation of fetal membranes is reported to be an inflammatory process. The present study compared the concentrations of certain pro inflammatory cytokines [Interleukin 1β (IL-1), Interleukin 6 (IL-6), Interleukin 8 (IL-8) and Tumor necrosis factor α (TNF-α) between the cows that developed RFM (n=10) and the cows that expelled fetal membranes normally (n=10) to find out if they could serve as a predictive tool for RFM. Blood samples were collected from the cows from 30 days before expected parturition through day -21, day -14, day -7, day -5, day -3, day -1, on the day of parturition (day 0), day 1 postpartum and the pro-inflammatory cytokines were estimated in blood plasma by ELISA method. The IL-1β concentration was significantly lower (Pmembranes normally from 3 days before calving till the day of calving. The plasma concentrations of IL-6 and IL-8 were also lower (Pmembranes normally. It may be inferred that the concentrations of IL-1, IL-6, IL-8 and TNF-α around parturition were altered in cows developing RFM compared to those expelled fetal membranes normally. Copyright © 2015. Published by Elsevier B.V.

Superconductive energy storage. Final report, January 1, 1976 - September 30, 1981

International Nuclear Information System (INIS)

Boom, R.W.

1982-01-01

Superconductive Magnetic Energy Storage (SMES) research and development for DOE from 1976-1981 has advanced the design of SMES from one deep tunnel to a 15 tunnel hour-glass design to the present low aspect ratio surface trench large diameter storage solenoid. This final report, which refers to all previous detailed reports and publications, concentrates on the last design of 1981, the low aspect ratio design. The SMES project is an ongoing project which includes the continuous development of designs and components. This report describes conceptual designs and the current state of development for the conductor, struts and cryogenics. Two companion efforts, rock mechanics and electrical systems, have been supported by the Wisconsin Utilities and are given less coverage here, although many references are listed in the 176-item bibliography. The present state of the project is that $15 million dollars is needed to take the next step. The work to be done is to improve the design, complete the component developments, design and test fabrication equipment and undertake credible cost estimates

Larval development and metamorphosis of Balanus albicostatus (Cirripedia: Thoracica); implications of temperature, food concentration and energetics

Digital Repository Service at National Institute of Oceanography (India)

Desai, D.V.; Khandeparker, L.; Shirayama, Y.

The influence of food concentrations (0.5, 1 and 2 x 105 cells ml sup(-1)) and temperatures (20 and 30 degrees C) on the survival, development, organic carbon and nitrogen content of Balanus albicostatus larvae was evaluated The effect of food...

Particle interactions in concentrated suspensions

International Nuclear Information System (INIS)

Mondy, L.A.; Graham, A.L.; Abbott, J.R.; Brenner, H.

1993-01-01

An overview is presented of research that focuses on slow flows of suspensions in which colloidal and inertial effects are negligibly small. The authors describe nuclear magnetic resonance imaging experiments to quantitatively measure particle migration occurring in concentrated suspensions undergoing a flow with a nonuniform shear rate. These experiments address the issue of how the flow field affects the microstructure of suspensions. In order to understand the local viscosity in a suspension with such a flow-induced, spatially varying concentration, one must know how the viscosity of a homogeneous suspension depends on such variables as solids concentration and particle orientation. The authors suggest the technique of falling ball viscometry, using small balls, as a method to determine the effective viscosity of a suspension without affecting the original microstructure significantly. They also describe data from experiments in which the detailed fluctuations of a falling ball's velocity indicate the noncontinuum nature of the suspension and may lead to more insights into the effects of suspension microstructure on macroscopic properties. Finally, they briefly describe other experiments that can be performed in quiescent suspensions (in contrast to the use of conventional shear rotational viscometers) in order to learn more about boundary effects in concentrated suspensions

Peripartum cardiomyopathy is associated with increased uric acid concentrations: A population based study.

Science.gov (United States)

Sagy, Iftach; Salman, Amjad Abu; Kezerle, Louise; Erez, Offer; Yoel, Idan; Barski, Leonid

Peri-partum cardiomyopathy (PPCM) is a clinical heart failure that usually develops during the final stage of pregnancy or the first months following delivery. High maternal serum uric acid concentrations have been previous associated with heart failure and preeclampsia. 1) To explored the clinical characteristics of PPCM patients; and 2) to determine the association between maternal serum uric acid concentrations and PPCM. This is a retrospective population based case control study. Cases and controls were matched 1:4 (for gestational age, medical history of cardiac conditions and creatinine); conditional logistic regression was used to identify clinical parameters that were associated with PPCM. The prevalence of peripartum cardiomyopathy at our institution was 1-3832 deliveries (42/160,964). In a matched multivariate analysis high maternal serum uric acid concentrations were associated with PPCM (O.R 1.336, 95% C.I 1.003-1.778). Uric acid concentrations were higher within the Non-Jewish patients and mothers of male infant with PPCM in compare to those without PPCM (p value 0.003 and 0.01 respectively). PPCM patients had increased maternal serum uric acid concentrations. This observation aligns with previous report regarding the increased uric acid concentration in women with preeclampsia and congestive heart failure, suggestive of a common underlying mechanism that mediates the myocardial damage. Copyright © 2017 Elsevier Inc. All rights reserved.

Photovoltaic Systems with and without Radiation Concentrators for Temperate and Tropical Regions

Directory of Open Access Journals (Sweden)

Vania Reis de Souza Sant’Anna

2015-11-01

Full Text Available The industrial development of solar photovoltaic technology has attracted investors and influenced governments to establish public policies for the sector. The present research consisted of studying, building and testing low concentration solar radiation systems for photovoltaic energy conversion. The study used optical nonimaging parameters for the V-trough type radiation concentrator constructed of anodized aluminum, to reflect and to cool. Designed to concentrate radiation by about two times and consisting of a set of photovoltaic modules connected in parallel, they were modeled in the Laboratory of Energy Area in the Department of Agricultural Engineering of the Federal University of Vicosa, Brazil, at the coordinates 20°45′14′′ S latitude, 42°52′53′′ W longitude and altitude 648.74 m. They were installed to the geographic North, with the same slope as the local latitude. For comparative analysis, it was determined the electrical characteristics for evaluation of the prototype’s performance with and without radiation concentration, the final productivity for cities in tropical and temperate regions and economic analysis for the system. It was concluded that the prototypes allowed for a gain of energy with concentration, about 31.3% more, and therefore a productivity gain for the analyzed cities in, kWh·kWp−1.

SP-100 coated-particle fuel development. Phase I. Final report

International Nuclear Information System (INIS)

1983-03-01

This document is the final report of Phase I of the SP-100 Coated-Particle Fuel Development Program conducted by GA Technologies Inc. for the US Department of Energy under contract DE-AT03-82SF11690. The general objective of the study conducted between September and December 1982 was to evaluate coated-particle type fuel as an alternate or backup fuel to the UO 2 tile-and-fin arrangement currently incorporated into the reference design of the SP-100 reactor core. This report presents and discusses the following topics in the order listed: the need for an alternative fuel for the SP-100 nuclear reactor; an abbreviated description of the reference and coated-particle fuel module concepts; the bases and results of the study and analysis leading to the preliminary design of a coated particle suitable for the SP-100 space power reactor; incorporation of the fuel particles into compacts and heat-pipe-cooled modules; initial efforts and plans to fabricate coated-particle fuel and fuel compacts; the design and performance of the proposed alternative core relative that of the reference fuel; and a summary of critical issues and conclusions consistent with the level of effort and duration of the study

CFD Modeling of Flow, Temperature, and Concentration Fields in a Pilot-Scale Rotary Hearth Furnace

Science.gov (United States)

Liu, Ying; Su, Fu-Yong; Wen, Zhi; Li, Zhi; Yong, Hai-Quan; Feng, Xiao-Hong

2014-01-01

A three-dimensional mathematical model for simulation of flow, temperature, and concentration fields in a pilot-scale rotary hearth furnace (RHF) has been developed using a commercial computational fluid dynamics software, FLUENT. The layer of composite pellets under the hearth is assumed to be a porous media layer with CO source and energy sink calculated by an independent mathematical model. User-defined functions are developed and linked to FLUENT to process the reduction process of the layer of composite pellets. The standard k-ɛ turbulence model in combination with standard wall functions is used for modeling of gas flow. Turbulence-chemistry interaction is taken into account through the eddy-dissipation model. The discrete ordinates model is used for modeling of radiative heat transfer. A comparison is made between the predictions of the present model and the data from a test of the pilot-scale RHF, and a reasonable agreement is found. Finally, flow field, temperature, and CO concentration fields in the furnace are investigated by the model.

Assessment of quantum dots concentrators for photovoltaic electricity production; Evaluation du potentiel de concentrateurs a quantum dots pour la production d'electricite photovoltaique. Rapport final

Energy Technology Data Exchange (ETDEWEB)

Schueler, A; Kostro, A; Huriet, B

2006-07-01

One of the most promising application of semiconductor nanostructures in the field of photovoltaics might be planar photoluminescent concentrators. Even for diffuse solar radiation, considerable concentration factors might be achieved. Such devices have originally been designed on the basis of organic dyes and might benefit from a considerably improved lifetime when replacing the organic fluorescent substances by inorganic semiconductor nanocrystals, so-called quantum dots. Quantum dot containing nanocomposite thin films are synthesized at EPFL-LESO by a low cost sol-gel process. In order to study the potential of the use of quantum dot solar concentrators in photovoltaic solar energy conversion, reliable computer simulations are needed. A tool for ray tracing simulations of quantum dot solar concentrators has been developed at EPFL-LESO on the basis of Monte-Carlo methods that are applied to polarization-dependent reflection/transmission at interfaces, photon absorption by the semiconductor nanocrystals and photoluminescent re-emission. Together with the knowledge on the optoelectronical properties of suitable photovoltaic cells, such simulations allow to predict the total efficiency of the envisaged concentrating PV systems, and to optimize pane dimensions, photoluminescent emission frequencies, and choice of PV cell types. (author)

Electro-oxidation of reverse osmosis concentrates generated in tertiary water treatment.

Science.gov (United States)

Pérez, G; Fernández-Alba, A R; Urtiaga, A M; Ortiz, I

2010-05-01

This work investigates the application of the electro-oxidation technology provided with boron doped diamond (BDD), an electrode material which has shown outstanding properties in oxidation of organic and inorganic compounds, for the treatment of reverse osmosis (RO) concentrates generated in tertiary wastewater treatment plants (WWTP). Chemical oxygen demand (COD), ammonium and several anions were measured during the electro-oxidation process, and the influence of the applied current density (20-200A/m(2)) was analysed on process kinetics. Analytical assessment showed that several emerging pollutants (pharmaceuticals, personal care products, stimulants, etc.) were presented both in the effluent of the secondary WWTP as well as in the RO concentrate. For this reason, a group of 10 emerging pollutants, those found with higher concentrations, was selected in order to test whether electro-oxidation can be also applied for their mitigation. In the removal of emerging pollutants the electrical current density in the range 20-100A/m(2) did not show influence likely due to the mass transfer resistance developed in the process when the oxidized solutes are present in such low concentrations. Their removal rates were fitted to first order expressions, and the apparent kinetic constants for the anodic oxidation of each compound were calculated. Finally, the formation of trihalomethanes (THMs) has been checked; concluding that after selecting the appropriate operational conditions the attained concentration is lower than the standards for drinking water established in European and EPA regulations. Copyright (c) 2010 Elsevier Ltd. All rights reserved.

Banking concentration and developments in FYROM: A country in transition

Directory of Open Access Journals (Sweden)

Nikolas Hourvouliades

2014-12-01

Full Text Available The Former Yugoslav Republic of Macedonia (FYROM belongs to the transition economies that have witnessed significant structural changes in their domestic markets during the 2000s. We examine the evolution of the banking competition from 2003 until 2011, covering the first period of economic growth followed by the acute financial crisis that still threatens European countries. We apply the Herfindahl–Hirschman index and the CR3 and CR5 indicators in order to estimate banking concentration on five industry variables. Our findings show that the market has been persistently operating under oligopolistic, if not monopolistic, conditions where the leading three or five institutions dominate the market. Foreign newcomers and legislative developments have not changed the situation during the past 10 years and bank customers seem to keep their preferences unaffected, staying loyal to their prior choices. We analyze the banking sector profitability since 2008 and during the economic crisis, as well as the operational performance and the future trends concerning this sector.

Transacsys PLC - Final Results

CERN Multimedia

2002-01-01

Final results from Transacsys PLC. A subsidary of this company was set up to develop the CERN EDH system into a commercial product but incurred too much financial loss so the project was cancelled (1/2 page).

PROGEOTHERM - National program for the development of geothermal energy in Switzerland - Final report; PROGEOTHERM - Programme national de developpement de la geothermie en Suisse - Rapport final

Energy Technology Data Exchange (ETDEWEB)

Vuataz, F.-D.

2007-07-01

This final report for the Swiss Federal Office of Energy (SFOE) reviews the current situation with respect to the use of geothermal energy in Switzerland and the problems faced. Action to be taken is examined. The report proposes that specialised further education, including the setting up of a Master of Advanced Studies course at the University of Neuchatel and support for courses at Universities of Applied Sciences. Research and development in the geothermal area and support for pilot and demonstration installations, new machinery and exploration methods are proposed. Also, political, organisational and financial aspects of the support programme are discussed.

Estimating Canopy Nitrogen Concentration in Sugarcane Using Field Imaging Spectroscopy

Directory of Open Access Journals (Sweden)

Marc Souris

2012-06-01

Full Text Available The retrieval of nutrient concentration in sugarcane through hyperspectral remote sensing is widely known to be affected by canopy architecture. The goal of this research was to develop an estimation model that could explain the nitrogen variations in sugarcane with combined cultivars. Reflectance spectra were measured over the sugarcane canopy using a field spectroradiometer. The models were calibrated by a vegetation index and multiple linear regression. The original reflectance was transformed into a First-Derivative Spectrum (FDS and two absorption features. The results indicated that the sensitive spectral wavelengths for quantifying nitrogen content existed mainly in the visible, red edge and far near-infrared regions of the electromagnetic spectrum. Normalized Differential Index (NDI based on FDS_(750/700 and Ratio Spectral Index (RVI based on FDS_(724/700 are best suited for characterizing the nitrogen concentration. The modified estimation model, generated by the Stepwise Multiple Linear Regression (SMLR technique from FDS centered at 410, 426, 720, 754, and 1,216 nm, yielded the highest correlation coefficient value of 0.86 and Root Mean Square Error of the Estimate (RMSE value of 0.033%N (n = 90 with nitrogen concentration in sugarcane. The results of this research demonstrated that the estimation model developed by SMLR yielded a higher correlation coefficient with nitrogen content than the model computed by narrow vegetation indices. The strong correlation between measured and estimated nitrogen concentration indicated that the methods proposed in this study could be used for the reliable diagnosis of nitrogen quantity in sugarcane. Finally, the success of the field spectroscopy used for estimating the nutrient quality of sugarcane allowed an additional experiment using the polar orbiting hyperspectral data for the timely determination of crop nutrient status in rangelands without any requirement of prior

Growth Interruption Effect on the Fabrication of GaAs Concentric Multiple Rings by Droplet Epitaxy

Directory of Open Access Journals (Sweden)

Fedorov A

2010-01-01

Full Text Available Abstract We present the molecular beam epitaxy fabrication and optical properties of complex GaAs nanostructures by droplet epitaxy: concentric triple quantum rings. A significant difference was found between the volumes of the original droplets and the final GaAs structures. By means of atomic force microscopy and photoluminescence spectroscopy, we found that a thin GaAs quantum well-like layer is developed all over the substrate during the growth interruption times, caused by the migration of Ga in a low As background.

Concentration and detection of hepatitis A virus and its indicator from artificial seawater using zeolite.

Science.gov (United States)

Cormier, Jiemin; Janes, Marlene

2016-09-01

Hepatitis A virus (HAV) infection is the leading worldwide cause of acute viral hepatitis, and outbreaks caused by this virus often occur in fecal polluted waters. Rapid concentration and detection of viral contamination in water environments can prevent economic loss and can identify the source of contamination within a short time. However, conventional methods for virus concentration are often laborious, time consuming, and subject to clogging. Furthermore, most methods require a secondary concentration step to reduce the final volume of samples. We developed a method to concentrate HAV from seawater using zeolite in aid of rapid detection. In this method,artificial seawater was inoculated with HAV (7-8 log TCID50) and filtered with zeolite. The viruses were then eluted from zeolite with sodium dodecyl sulfate and detected via real-time PCR (qPCR). Zeolite was able to concentrate HAV from artificial seawater with ∼99% efficiency in less than 5min and was more efficient in seawater than in fresh water. The entire concentration and detection can be done in approximately 2h. Compared to existing methods, this method eliminated the need for a secondary concentration step as well as the necessity to modify the pH or salinity of the seawater during concentration, and was simple and inexpensive. Copyright © 2016 Elsevier B.V. All rights reserved.

Recovery of protactinium-231 and thorium-230 from cotter concentrate: pilot plant operatins and process development

International Nuclear Information System (INIS)

Hertz, M.R.; Figgins, P.E.; Deal, W.R.

1983-01-01

The equipment and methods used to recover and purify 339 g of thorium-230 and 890 mg of protactinium-231 from 22 of the 1251 drums of Cotter Concentrate are described. The process developed was (1) dissolution at 100 0 C in concentrated nitric acid and dilution to 2 to 3 molar acid, (2) filtration to remove undissolved solids (mostly silica filter aid), (3) extraction of uranium with di-sec-butyl-phenyl phophonate (DSBPP) in carbon tetrachloride, (4) extraction of both thorium and protactinium with tri-n-octylphosphine oxide (TOPO) in carbon tetrachloride followed by selective stripping of the thorium with dilute of sulfuric acid, (5) thorium purification using oxalic acid, (6) stripping protactinium from the TOPO with oxalic acid, and (7) protactinium purification through a sequence of steps. The development of the separation procedures, the design of the pilot plant, and the operating procedures are described in detail. Analytical procedures are given in an appendix. 8 figures, 4 tables

Development of a Direct Spectrophotometric and Chemometric Method for Determining Food Dye Concentrations.

Science.gov (United States)

Arroz, Erin; Jordan, Michael; Dumancas, Gerard G

2017-07-01

An ultraviolet visible (UV-Vis) spectrophotometric and partial least squares (PLS) chemometric method was developed for the simultaneous determination of erythrosine B (red), Brilliant Blue, and tartrazine (yellow) dyes. A training set (n = 64) was generated using a full factorial design and its accuracy was tested in a test set (n = 13) using a Box-Behnken design. The test set garnered a root mean square error (RMSE) of 1.79 × 10 -7 for blue, 4.59 × 10 -7 for red, and 1.13 × 10 -6 for yellow dyes. The relatively small RMSE suggests only a small difference between predicted versus measured concentrations, demonstrating the accuracy of our model. The relative error of prediction (REP) for the test set were 11.73%, 19.52%, 19.38%, for blue, red, and yellow dyes, respectively. A comparable overlay between the actual candy samples and their replicated synthetic spectra were also obtained indicating the model as a potentially accurate method for determining concentrations of dyes in food samples.

Advanced wind turbine near-term product development. Final technical report

Energy Technology Data Exchange (ETDEWEB)

None

1996-01-01

In 1990 the US Department of Energy initiated the Advanced Wind Turbine (AWT) Program to assist the growth of a viable wind energy industry in the US. This program, which has been managed through the National Renewable Energy Laboratory (NREL) in Golden, Colorado, has been divided into three phases: (1) conceptual design studies, (2) near-term product development, and (3) next-generation product development. The goals of the second phase were to bring into production wind turbines which would meet the cost goal of $0.05 kWh at a site with a mean (Rayleigh) windspeed of 5.8 m/s (13 mph) and a vertical wind shear exponent of 0.14. These machines were to allow a US-based industry to compete domestically with other sources of energy and to provide internationally competitive products. Information is given in the report on design values of peak loads and of fatigue spectra and the results of the design process are summarized in a table. Measured response is compared with the results from mathematical modeling using the ADAMS code and is discussed. Detailed information is presented on the estimated costs of maintenance and on spare parts requirements. A failure modes and effects analysis was carried out and resulted in approximately 50 design changes including the identification of ten previously unidentified failure modes. The performance results of both prototypes are examined and adjusted for air density and for correlation between the anemometer site and the turbine location. The anticipated energy production at the reference site specified by NREL is used to calculate the final cost of energy using the formulas indicated in the Statement of Work. The value obtained is $0.0514/kWh in January 1994 dollars. 71 figs., 30 tabs.

Development of scan analysis techniques employing a small computer. Final report, February 1, 1963--July 31, 1976

International Nuclear Information System (INIS)

Kuhl, D.E.

1976-01-01

During the thirteen year duration of this contract the goal has been to develop and apply computer based analysis of radionuclide scan data so as to make available improved diagnostic information based on a knowledge of localized quantitative estimates of radionuclide concentration. Results are summarized

Concentration profiles near an activated enzyme.

Science.gov (United States)

Park, Soohyung; Agmon, Noam

2008-09-25

When a resting enzyme is activated, substrate concentration profile evolves in its vicinity, ultimately tending to steady state. We use modern theories for many-body effects on diffusion-influenced reactions to derive approximate analytical expressions for the steady-state profile and the Laplace transform of the transient concentration profiles. These show excellent agreement with accurate many-particle Brownian-dynamics simulations for the Michaelis-Menten kinetics. The steady-state profile has a hyperbolic dependence on the distance of the substrate from the enzyme, albeit with a prefactor containing the complexity of the many-body effects. These are most conspicuous for the substrate concentration at the surface of the enzyme. It shows an interesting transition as a function of the enzyme turnover rate. When it is high, the contact concentration decays monotonically to steady state. However, for slow turnover it is nonmonotonic, showing a minimum due to reversible substrate binding, then a maximum due to diffusion of new substrate toward the enzyme, and finally decay to steady state. Under certain conditions one can obtain a good estimate for the critical value of the turnover rate constant at the transition.

NMS Prototype development final report

International Nuclear Information System (INIS)

Lepetich, J.E.

1993-01-01

Program for development of NMS prototype for LAMPF consisted of 5 tasks: crystal procurement specification, inspection/evaluation of CsI crystals, design/fabrication of crystal housing, design/fabrication of PMT shields, and packaging of crystals in the housing

Predictive value of clinical risk indicators in child development: final results of a study based on psychoanalytic theory

Directory of Open Access Journals (Sweden)

Maria Cristina Machado Kupfer

2010-03-01

Full Text Available We present the final results of a study using the IRDI (Clinical Risk Indicators in Child Development. Based on a psychoanalytic approach, 31 risk signs for child development were constructed and applied to 726 children between the ages of 0 and 18 months. One sub-sample was evaluated at the age of three. The results showed a predictive capacity of IRDIs to indicate developmental problems; 15 indicators for the IRDI were also highlighted that predict psychic risk for the constitution of the subject.

Final Technical Report: Using Solid Particles as Heat Transfer Fluid for use in Concentrating Solar Power (CSP) Plants

Energy Technology Data Exchange (ETDEWEB)

Lattanzi, Aaron [Univ. of Colorado, Boulder, CO (United States); Hrenya, Christine [Univ. of Colorado, Boulder, CO (United States)

2016-03-31

In today’s industrial economy, energy consumption has never been higher. Over the last 15 years the US alone has consumed an average of nearly 100 quadrillion BTUs per year [21]. A need for clean and renewable energy sources has become quite apparent. The SunShot Initiative is an ambitious effort taken on by the United States Department of Energy that targets the development of solar energy that is cost-competitive with other methods for generating electricity. Specifically, this work is concerned with the development of concentrating solar power plants (CSPs) with granular media as the heat transfer fluid (HTF) from the solar receiver. Unfortunately, the prediction of heat transfer in multiphase flows is not well understood. For this reason, our aim is to fundamentally advance the understanding of multiphase heat transfer, particularly in gas-solid flows, while providing quantitative input for the design of a near black body receiver (NBB) that uses solid grains (like sand) as the HTF. Over the course of this three-year project, a wide variety of contributions have been made to advance the state-of-the art description for non-radiative heat transfer in dense, gas-solid systems. Comparisons between a state-of-the-art continuum heat transfer model and discrete element method (DEM) simulations have been drawn. The results of these comparisons brought to light the limitations of the continuum model due to inherent assumptions in its derivation. A new continuum model was then developed for heat transfer at a solid boundary by rigorously accounting for the most dominant non-radiative heat transfer mechanism (particle-fluid-wall conduction). The new model is shown to be in excellent agreement with DEM data and captures the dependence of heat transfer on particle size, a dependency that previous continuum models were not capable of. DEM and the new continuum model were then employed to model heat transfer in a variety of receiver geometries. The results provided crucial

Final Technical Report - In-line Uranium Immunosensor

International Nuclear Information System (INIS)

Blake, Diane A.

2006-01-01

In this project, personnel at Tulane University and Sapidyne Instruments Inc. developed an in-line uranium immunosensor that could be used to determine the efficacy of specific in situ biostimulation approaches. This sensor was designed to operate autonomously over relatively long periods of time (2-10 days) and was able to provide near real-time data about uranium immobilization in the absence of personnel at the site of the biostimulation experiments. An alpha prototype of the in-line immmunosensor was delivered from Sapidyne Instruments to Tulane University in December of 2002 and a beta prototype was delivered in November of 2003. The beta prototype of this instrument (now available commercially from Sapidyne Instruments) was programmed to autonomously dilute standard uranium to final concentrations of 2.5 to 100 nM (0.6 to 24 ppb) in buffer containing a fluorescently labeled anti-uranium antibody and the uranium chelator, 2,9-dicarboxyl-1,10-phenanthroline. The assay limit of detection for hexavalent uranium was 5.8 nM or 1.38 ppb. This limit of detection is well below the drinking water standard of 30 ppb recently promulgated by the EPA. The assay showed excellent precision; the coefficients of variation (CV's) in the linear range of the assay were less than 5% and CV?s never rose above 14%. Analytical recovery in the immunosensors-based assay was assessed by adding variable known quantities of uranium to purified water samples. A quantitative recovery (93.75% - 108.17%) was obtained for sample with concentrations from 7.5 to 20 nM (2-4.75 ppb). In August of 2005 the sensor was transported to Oak Ridge National Laboratory, for testing of water samples at the Criddle test site (see Wu et al., Environ. Sci. Technol. 40:3978-3985 2006 for a description of this site). In this first on-site test, the in-line sensor was able to accurately detect changes in the concentrations of uranium in effluent samples from this site. Although the absolute values for the uranium

Design and test of the final ALICE SDD CARLOS end ladder board

CERN Document Server

Antinori, S; Falchieri, D; Gabrielli, A; Gandolfi, E; Masetti, M; Tosellob, F

2007-01-01

The paper presents the design and test of the final prototype of the CARLOS (Compression And Run Length Encoding Subsystem) end ladder board that is going to be used in the ALICE experiment at CERN. This board is able to compress data coming from one Silicon Drift Detector (SDD) front-end electronics and to send them towards the data concentrator card CARLOSrx in counting room via a 800 Mb/s optical link. The board design faces several constraints, mainly size (54x49 mm) and radiation tolerance: for this reason the board contains several CERN developed ASICs. A test setup has been realized for selecting the good devices among the 500 cards already produced.

Development of real-time measurement of methanol-concentration in polymer electrolyte membrane using a local NMR sensor

International Nuclear Information System (INIS)

Ogawa, Kuniyasu; Ito, Kohei; Haishi, Tomoyuki

2007-01-01

A real-time sensor to measure methanol concentration in polymer electrolyte membrane (PEM) was developed for reducing methanol cross-over in Direct Methanol Fuel Cell (DMFC). The principle of the methanol sensor is based on the chemical shift of CH and OH species under high magnetic field. The sensor consists of a planar surface coil of 1.3 mm outside diameter. NMR signal from PEM being exposed to CH3OH solvent was measured using NMR sensor. Time-dependence changes of methanol concentration in PEM were obtained from analyzing spectrum of NMR signal. (author)

Review of concentrating solar thermal power industry in China: Status quo, problems, trend and countermeasures

Science.gov (United States)

Zou, Jiajun

2018-01-01

Concentrating solar thermal power (CSP) industry is a strategic emerging industry in China. Its further development is of great significance for promoting the energy revolution, achieving energy saving and emission reduction. In this paper, China’s CSP industry is systematically analysed. First of all, the status quo is elaborated from the perspectives of relevant policies and regulations, market and generation technology development. Secondly, the problems and the underlying reasons of China’s CSP industry are deeply studied. On this basis, the future trends of CSP are expounded on the three levels of policy, market and power generation technology. Finally, a series of feasible countermeasures are put forward, designed to promote the development of CSP industry and the transformation of energy structure.

Photodegradation in multiple-dye luminescent solar concentrators

International Nuclear Information System (INIS)

Mooney, Alex M.; Warner, Kathryn E.; Fontecchio, Paul J.; Zhang, Yu-Zhong; Wittmershaus, Bruce P.

2013-01-01

Combining multiple organic dyes to form a fluorescence resonance energy transfer (FRET) network is a useful strategy for extending the spectral range of sunlight absorbed by a luminescent solar concentrator (LSC). Excitation transfer out of the higher energy level dyes in the transfer series competes effectively with their photodegradation rates. Improvements in photostability up to a factor of 18 are observed for the first dye in the FRET series. FRET networks are shown to be a viable means of decreasing the rate of photodegradation of organic dyes used in LSCs. This comes at the expense of the final dye in the network; the depository of most of the excitations created by absorbing sunlight. The photostability and performance of an efficient FRET LSC rest heavily on the photostability and fluorescence quantum yield of the final dye. -- Highlights: • Photodegradation kinetics of multiple-dye FRET LSCs are reported. • The FRET network decreased the first dye's photodegradation rate by a factor of 18. • The final dye in the FRET LSC protects other dyes at its own expense. • The final dye must have excellent photostability and fluorescence quantum yield

Technology Enabling Ultra High Concentration Multi-Junction Cells. Final report

Energy Technology Data Exchange (ETDEWEB)

Bedair, S. M.; Colter, Peter

2016-03-30

The project goal is to enable multijunction cells to operate at greater than 2000× suns intensity with efficiency above forty percent. To achieve this goal the recipients have developed a robust high-bandgap tunnel junction, reduce series resistance, and integrated a practical heat dissipation scheme.

Research and development on procedures to stabilize acaricides in livestock dips. Proceedings of a final research co-ordination meeting

International Nuclear Information System (INIS)

1997-11-01

Ticks and mites are serious ectoparasites of livestock in many countries. As vectors of animal diseases they pose a threat to livestock production. Traditionally, different types of acaricides are used to control them. One of the most commonly used tick control techniques is to force animals to walk through an acaricide suspension in a trough or Cattle Dip. Dipping is quite effective as the entire body of the animal gets treated with the acaricide. However, with increased usage the concentration of the acaricide in the 'dip' declines due to removal by the animal and degradation by biological and chemicals processes. The dissipation of the acaricide results in loss of efficacy of the 'dip', and may also enhance the development of resistance by the ectoparasites to the acaricides. Maintenance of an effective concentration, by periodic recharge or stabilization of the acaricide, is essential to assure efficient and cost-effective control and to minimize chances of resistance to develop. In 1990, the FAO/IAEA Joint Division, recognizing the need for co-ordinated research on studying the dissipation of acaricides in cattle dips and developing procedures to stabilize them, established a 5-year Co-ordinated Research Programme on Development of Procedures to Stabilize Acaricides in Livestock Dips and of Simplified Methods to Measure Their Concentration, Using Nuclear Techniques. In initiating this programme, the Joint Division recognized that major gaps exist in the knowledge in this area which, if filled, would greatly aid developing countries in their effort to more effectively use acaricides to protect animal health. This TECDOC reports the accomplishments of this programme

Development of scan analysis techniques employing a small computer. Final report, February 1, 1963--July 31, 1976

Energy Technology Data Exchange (ETDEWEB)

Kuhl, D.E.

1976-08-05

During the thirteen year duration of this contract the goal has been to develop and apply computer based analysis of radionuclide scan data so as to make available improved diagnostic information based on a knowledge of localized quantitative estimates of radionuclide concentration. Results are summarized. (CH)

Interactions of CO{sub 2} with temperature and other climate variables: Response of vegetation. Final report, September 1, 1988--August 31, 1993

Energy Technology Data Exchange (ETDEWEB)

Acock, B.; Kimball, B.A.

1995-02-01

The current project was initiated in 1991, and full details of the scope of the project are contained in the original proposal. that original proposal was reviewed and approved for three years funding. Progress made in 1991-92 and 1992-93 was described in annual Progress Reports and Statements of Work. This document summarizes progress made over the duration of the project, but with an emphasis on the final year`s (1993-94) results. Several of the important experiments are ongoing, to the extent that alternative funding could be arranged, and analyses of data from several of the earlier completed experiments is continuing. Therefore, this Final Report is also intermediary in nature, and additional results from this project will be reported in the open literature in the future. The overall objectives of the project were: (1) to examine experimentally, for major crop species, the interacting effects of CO{sub 2} concentration, temperature, and water availability on plant growth and development, (2) to model these interactions, and (3) to continue developing physiologically-based mechanistic models for predicting crop response to increased CO{sub 2} concentration and future global climate change.

Electric Power Infrastructure Reliability And Security Research And Development Initiative. Final report

International Nuclear Information System (INIS)

Dale, S.; Meeker, R.; Steurer, M.; Li, H.; Pamidi, S.; Rodrigo, H.; Suryanarayanan, S.; Cartes, D.; Ordonez, J.; Domijan, A.; Liu, W.; Cox, D.; McLaren, P.; Hovsapian, R.; Edwards, D.; Simmons, S.; Wilde, N.; Woodruff, S.; Kopriva, D.; Hussaini, Y.; Mohammed, O.; Zheng, J.; Baldwin, T.L.

2008-01-01

This is the final scientific/technical report for the Electric Power Infrastructure Reliability and Security R and D Initiative sponsored by the U.S. Department of Energy, Office of Electricity Delivery and Energy Reliability, under award number DE-FG02-05CH11292. This report covers results from the FSU-led, multi-institution effort conducted over the period 8/15/05 to 10/14/2007. Building upon existing infrastructure for power systems research, modeling, and simulation, the Center for Advanced Power Systems (CAPS) at Florida State University (FSU) is developing world-class programs in electric power systems research and education to support future electric power system needs and challenges. With U.S. Department of Energy Support, FSU CAPS has engaged in a multi-faceted effort to conduct basic and applied research towards understanding, developing, and deploying technologies and approaches that can lead to improved reliability and security of the North American electric power generation and delivery infrastructure. This wide-reaching project, through a number of carefully selected thrusts cutting across several research disciplines, set out to address key terrestrial electric utility power system issues and challenges. The challenges and the thrusts to address them were arrived at through analysis of a number of national reports and recommendations combined with input from an experienced multi-disciplined team of power systems research staff and faculty at FSU CAPS. The resulting project effort can be grouped into four major areas: - Power Systems and New Technology Insertion - Controls, Protection, and Security - Simulation Development - High Temperature Superconductivity (HTS)

Development of Manufacturing Technology to Accelerate Cost Reduction of Low Concentration and

Energy Technology Data Exchange (ETDEWEB)

Detrick, Adam [The Solaria Corporation, Fremont, CA (United States)

2017-09-27

The purpose of this project was to accelerate deployment of cost-effective US-based manufacturing of Solaria’s unique c-Si module technology. This effort successfully resulted in the development of US-based manufacturing technology to support two highly-differentiated, market leading product platforms. The project was initially predicated on developing Solaria’s low-concentration PV (LCPV) module technology which at the time of the award was uniquely positioned to exceed the SunShot price goal of $0.50/Wp for standard c-Si modules. The Solaria LCPV module is a 2.5x concentrator that leverages proven, high-reliability PV module materials and low silicon cell usage into a technology package that already had the lowest direct material cost and leading Levelized Cost of Electricity (LCOE). With over 25 MW commercially deployed globally, the Solaria module was well positioned to continue to lead in PV module cost reduction. Throughout the term of the contract, market conditions changed dramatically and so to did Solaria’s product offerings to support this. However, the manufacturing technology developed for the LCPV module was successfully leveraged and optimized to support two new and different product platforms. BIPV “PowerVision” and High-efficiency “PowerXT” modules. The primary barrier to enabling high-volume PV module manufacturing in the US is the high manual labor component in certain unique aspects of our manufacturing process. The funding was used to develop unique manufacturing automation which makes the manual labor components of these key processes more efficient and increase throughput. At the core of Solaria’s product offerings are its unique and proprietary techniques for dicing and re-arranging solar cells into modules with highly-differentiated characteristics that address key gaps in the c-Si market. It is these techniques that were successfully evolved and deployed into US-based manufacturing site with SunShot funding. Today, Solaria

Mathematical modelling of immobilization of radioactive evaporator concentrate from nuclear power plants

International Nuclear Information System (INIS)

Plecas, I.B.

2005-01-01

Traditional methods of processing evaporator concentrates from NPP are evaporation and cementation.These methods allow to transform a liquid radioactive waste into the rather inert form, suitable for a final disposal. To assess the safety for disposal of radioactive mortar-waste composition, the leaching of 137 Cs from immobilized radioactive evaporator concentrate into a surrounding fluid has been studied. Leaching tests were carried out in accordance with a method recommended by IAEA. Determination of retardation factors, K F and coefficients of distribution, k d , using a simplified mathematical model for analyzing the migration of radionuclides, has been developed. In our experiment we have achieved the lowest leaching values after 60 days in samples. Results presented in this paper are examples of results obtained in a 20 year mortar and concrete testing project, which will influence the design of the engineered trenches system for a future central Serbian radioactive waste disposal center. (author)

How would a decline in sperm concentration over time influence the probability of pregnancy?

DEFF Research Database (Denmark)

Slama, R.; Jensen, Tina Kold; Scheike, T.

2004-01-01

BACKGROUND: Reports have suggested a decline in sperm concentration during the second half of the 20th century. The effect of this decline on fecundability (the monthly probability of pregnancy) could be detected in principle by a study of time to pregnancy. In practice, the amplitude of this exp......BACKGROUND: Reports have suggested a decline in sperm concentration during the second half of the 20th century. The effect of this decline on fecundability (the monthly probability of pregnancy) could be detected in principle by a study of time to pregnancy. In practice, the amplitude...... of this expected effect is not well known and the statistical power of time-to-pregnancy studies to detect it has not been explored. METHODS: We developed a nonparametric model to describe a temporal decline in sperm concentration using data on French semen donors. We then applied this model to 419 Danish couples...... planning a first pregnancy in 1992, to predict their time to pregnancy as if the pregnancy attempt had begun during earlier decades with higher sperm concentrations. Finally, we used bootstrap simulations to estimate the statistical power of prospective or retrospective studies that compared fecundability...

Compact high-sensitivity potentiometer for detection of low ion concentrations in liquids

Science.gov (United States)

Balevicius, Z.; Lescinskas, R.; Celiesiute, R.; Stirke, A.; Balevicius, S.; Kersulis, S.; Bleizgys, V.; Maciuleviciene, R.; Ramanavicius, A.; Zurauskiene, N.

2018-04-01

The compact potentiometer, based on an electronic circuit protected from electrostatic and electromagnetic interference, was developed for the measurement of low ion concentrations in liquids. The electronic circuit of the potentiometer, consisting of analogous and digital parts, enables the measurement of fA currents. This makes it possible to perform reliable measurements of ion concentrations in liquids that are as small as 10-8-10-7M. The instrument was tested using electrodes that were selective for tetraphenylphosphonium (TPP+) ions. It was demonstrated that the characteristic response time of the potentiometer electronic circuit to changes in the concentration of these ions in a liquid was in the order of 10 s. An investigation of TPP+ absorption by baker yeast has shown that this device can be successfully used for long term (several hours) measurements with zero signal drift, which was about 1 μV/s. Finally, due to the small dimensions of the electronic circuit (7.5 × 2 × 1.5 cm), this potentiometer can be easily installed at a large apparatus in the laboratory condition (≈25 °C), such as high pulsed electrical generators of magnetic fields that are used in electroporation studies of biological cells.

Biogas final digestive byproduct applied to croplands as fertilizer contains high levels of steroid hormones

DEFF Research Database (Denmark)

Rodriguez-Navas, Carlos; Björklund, Erland; Halling-Sørensen, Bent

2013-01-01

that utilize different anaerobic digestion technologies (mesophilic and thermophilic) from swine manure and other organic wastes. Individual hormone concentration levels were observed up to 1478 ng g(-1) dry weight or 22.5 mg kg(-1) N with estrone and progesterone reaching highest concentration levels....... Evaluation of the potential environmental burden through the application in agriculture was also assessed on the basis of predicted environmental concentrations. This study indicates that the biogas digestion process does not completely remove steroid hormones from livestock manure and use of final digestate......In this study we evaluate and demonstrate the occurrence of nine natural and one synthetic steroid hormone, including estrogens, androgens and progestagens in biogas final digestate byproduct (digestion liquid) commonly used as an agricultural fertilizer. We investigated two biogas sites...

Tritium concentrations in the atmospheric environment at Rokkasho, Japan before the final testing of the spent nuclear fuel reprocessing plant

Energy Technology Data Exchange (ETDEWEB)

Akata, Naofumi, E-mail: nao@ies.or.jp [Department of Radioecology, Institute for Environmental Sciences, 1-7 Ienomae, Obuchi, Rokkasho, Aomori 039-3212 (Japan); Kakiuchi, Hideki [Department of Radioecology, Institute for Environmental Sciences, 1-7 Ienomae, Obuchi, Rokkasho, Aomori 039-3212 (Japan); Shima, Nagayoshi [Entex Inc., 1-2-8 Asahi, Kashiwa, Chiba 277-0852 (Japan); Iyogi, Takashi [Department of Radioecology, Institute for Environmental Sciences, 1-7 Ienomae, Obuchi, Rokkasho, Aomori 039-3212 (Japan); Momoshima, Noriyuki [Radioisotope Center, Kyushu University, 6-10-1 Hakozaki, Higashi-ku, Fukuoka 812-8581 (Japan); Hisamatsu, Shun' ichi [Department of Radioecology, Institute for Environmental Sciences, 1-7 Ienomae, Obuchi, Rokkasho, Aomori 039-3212 (Japan)

2011-09-15

This study aimed at obtaining background tritium concentrations in precipitation and air at Rokkasho where the first commercial spent nuclear fuel reprocessing plant in Japan has been under construction. Tritium concentration in monthly precipitation during fiscal years 2001-2005 had a seasonal variation pattern which was high in spring and low in summer. The tritium concentration was higher than that observed at Chiba City as a whole. The seasonal peak concentration at Rokkasho was generally higher than that at Chiba City, while the baseline concentrations of both were similar. The reason for the difference may be the effect of air mass from the Asian continent which is considered to have high tritium concentration. Atmospheric tritium was operationally separated into HTO, HT and hydrocarbon (CH{sub 3}T) fractions, and the samples collected every 3 d-14 d during fiscal year 2005 were analyzed for these fractions. The HTO concentration as radioactivity in water correlated well with that in the precipitation samples. The HT concentration was the highest among the chemical forms analyzed, followed by the HTO and CH{sub 3}T concentrations. The HT and CH{sub 3}T concentrations did not have clear seasonal variation patterns. The HT concentration followed the decline previously reported by Mason and Ostlund with an apparent half-life of 4.8 y. The apparent and environmental half-lives of CH{sub 3}T were estimated as 9.2 y and 36.5 y, respectively, by combining the present data with literature data. The Intergovernmental Panel on Climate Change used the atmospheric lifetime of 12 y for CH{sub 4} to estimate global warming in its 2007 report. The longer environmental half-life of CH{sub 3}T suggested its supply from other sources than past nuclear weapon testing in the atmosphere. - Highlights: > We observed background tritium concentrations in atmospheric environment at Rokkasho, Japan. > Tritium concentration in precipitation was high in spring and low in summer. > The

Tritium concentrations in the atmospheric environment at Rokkasho, Japan before the final testing of the spent nuclear fuel reprocessing plant

International Nuclear Information System (INIS)

Akata, Naofumi; Kakiuchi, Hideki; Shima, Nagayoshi; Iyogi, Takashi; Momoshima, Noriyuki; Hisamatsu, Shun'ichi

2011-01-01

This study aimed at obtaining background tritium concentrations in precipitation and air at Rokkasho where the first commercial spent nuclear fuel reprocessing plant in Japan has been under construction. Tritium concentration in monthly precipitation during fiscal years 2001-2005 had a seasonal variation pattern which was high in spring and low in summer. The tritium concentration was higher than that observed at Chiba City as a whole. The seasonal peak concentration at Rokkasho was generally higher than that at Chiba City, while the baseline concentrations of both were similar. The reason for the difference may be the effect of air mass from the Asian continent which is considered to have high tritium concentration. Atmospheric tritium was operationally separated into HTO, HT and hydrocarbon (CH 3 T) fractions, and the samples collected every 3 d-14 d during fiscal year 2005 were analyzed for these fractions. The HTO concentration as radioactivity in water correlated well with that in the precipitation samples. The HT concentration was the highest among the chemical forms analyzed, followed by the HTO and CH 3 T concentrations. The HT and CH 3 T concentrations did not have clear seasonal variation patterns. The HT concentration followed the decline previously reported by Mason and Ostlund with an apparent half-life of 4.8 y. The apparent and environmental half-lives of CH 3 T were estimated as 9.2 y and 36.5 y, respectively, by combining the present data with literature data. The Intergovernmental Panel on Climate Change used the atmospheric lifetime of 12 y for CH 4 to estimate global warming in its 2007 report. The longer environmental half-life of CH 3 T suggested its supply from other sources than past nuclear weapon testing in the atmosphere. - Highlights: → We observed background tritium concentrations in atmospheric environment at Rokkasho, Japan. → Tritium concentration in precipitation was high in spring and low in summer. → The atmospheric HT

Concentration and speciation of heavy metals in six different sewage sludge-composts

International Nuclear Information System (INIS)

Cai Quanying; Mo Cehui; Wu Qitang; Zeng Qiaoyun; Katsoyiannis, Athanasios

2007-01-01

This study presents the concentrations and speciation of heavy metals (HMs) in six different composts of sewage sludges deriving from two wastewater treatment plants in China. After 56 days of sludge composting with rice straw at a low C/N ratio (13:1), cadmium (Cd), copper (Cu), lead (Pb) and zinc (Zn) were enriched in sludge composts, exhibiting concentrations that varied from 0.75 to 2.0, 416 to 458, 66 to 168 and 1356 to 1750 mg kg -1 dry weight (d.w.), respectively. The concentrations increased by 12-60% for Cd, 8-17% for Cu, 15-43% for Pb and 14-44% for Zn compared to those in sewage sludges. The total concentrations of individual or total elements in the final composts exceeded the maximum permissible limits proposed for compost or fertilizer. In all the final composts, more than 70% of total Cu was associated with organic matter-bound fraction, while Zn was mainly concentrated in exchangeable and Fe-Mn oxide-bound fractions which implied the high mobility and bioavailability. Continuously aerated composting treatment exhibited better compost quality and lower potential toxicity of HMs, whereas inoculant with microorganism and enzyme spiked during composting had no obvious advantage on humification of organic matter and on reducing HM mobility and bioavailability

Error exponents for entanglement concentration

International Nuclear Information System (INIS)

Hayashi, Masahito; Koashi, Masato; Matsumoto, Keiji; Morikoshi, Fumiaki; Winter, Andreas

2003-01-01

Consider entanglement concentration schemes that convert n identical copies of a pure state into a maximally entangled state of a desired size with success probability being close to one in the asymptotic limit. We give the distillable entanglement, the number of Bell pairs distilled per copy, as a function of an error exponent, which represents the rate of decrease in failure probability as n tends to infinity. The formula fills the gap between the least upper bound of distillable entanglement in probabilistic concentration, which is the well-known entropy of entanglement, and the maximum attained in deterministic concentration. The method of types in information theory enables the detailed analysis of the distillable entanglement in terms of the error rate. In addition to the probabilistic argument, we consider another type of entanglement concentration scheme, where the initial state is deterministically transformed into a (possibly mixed) final state whose fidelity to a maximally entangled state of a desired size converges to one in the asymptotic limit. We show that the same formula as in the probabilistic argument is valid for the argument on fidelity by replacing the success probability with the fidelity. Furthermore, we also discuss entanglement yield when optimal success probability or optimal fidelity converges to zero in the asymptotic limit (strong converse), and give the explicit formulae for those cases

Leading trends in environmental regulation that affect energy development. Final report

Energy Technology Data Exchange (ETDEWEB)

Steele, R V; Attaway, L D; Christerson, J A; Kikel, D A; Kuebler, J D; Lupatkin, B M; Liu, C S; Meyer, R; Peyton, T O; Sussin, M H

1980-01-01

Major environmental issues that are likely to affect the implementation of energy technologies between now and the year 2000 are identified and assessed. The energy technologies specifically addressed are: oil recovery and processing; gas recovery and processing; coal liquefaction; coal gasification (surface); in situ coal gasification; direct coal combustion; advanced power systems; magnetohydrodynamics; surface oil shale retorting; true and modified in situ oil shale retorting; geothermal energy; biomass energy conversion; and nuclear power (fission). Environmental analyses of these technologies included, in addition to the main processing steps, the complete fuel cycle from resource extraction to end use. A comprehensive survey of the environmental community (including environmental groups, researchers, and regulatory agencies) was carried out in parallel with an analysis of the technologies to identify important future environmental issues. Each of the final 20 issues selected by the project staff has the following common attributes: consensus of the environmental community that the issue is important; it is a likely candidate for future regulatory action; it deals with a major environmental aspect of energy development. The analyses of the 20 major issues address their environmental problem areas, current regulatory status, and the impact of future regulations. These analyses are followed by a quantitative assessment of the impact on energy costs and nationwide pollutant emissions of possible future regulations. This is accomplished by employing the Strategic Environmental Assessment System (SEAS) for a subset of the 20 major issues. The report concludes with a more general discussion of the impact of environmental regulatory action on energy development.

Phase 0: goal study for the technical and economic evaluation of the Compound Parabolic Concentrator (CPC) concept applied to solar thermal and photovoltaic collectors. Final report

Energy Technology Data Exchange (ETDEWEB)

None

1975-06-01

This report presents the results of a quick, six-week technical and economic evaluation of the compound parabolic concentrator (CPC) solar collector. The purpose of this effort was to provide an initial phase of a goals study that is directed toward recommending relative priorities for development of the compound parabolic concentrator concept. The findings of this study are of a very preliminary nature. Conclusions based on study findings at this depth should be considered preliminary and subject to revision and review in later phases.

C-Band Airport Surface Communications System Standards Development. Phase II Final Report. Volume 2: Test Bed Performance Evaluation and Final AeroMACS Recommendations

Science.gov (United States)

Hall, Edward; Magner, James

2011-01-01

This report is provided as part of ITT s NASA Glenn Research Center Aerospace Communication Systems Technical Support (ACSTS) contract NNC05CA85C, Task 7: New ATM Requirements-Future Communications, C-Band and L-Band Communications Standard Development and was based on direction provided by FAA project-level agreements for New ATM Requirements-Future Communications. Task 7 included two subtasks. Subtask 7-1 addressed C-band (5091- to 5150-MHz) airport surface data communications standards development, systems engineering, test bed and prototype development, and tests and demonstrations to establish operational capability for the Aeronautical Mobile Airport Communications System (AeroMACS). Subtask 7-2 focused on systems engineering and development support of the L-band digital aeronautical communications system (L-DACS). Subtask 7-1 consisted of two phases. Phase I included development of AeroMACS concepts of use, requirements, architecture, and initial high-level safety risk assessment. Phase II builds on Phase I results and is presented in two volumes. Volume I is devoted to concepts of use, system requirements, and architecture, including AeroMACS design considerations. Volume II (this document) describes an AeroMACS prototype evaluation and presents final AeroMACS recommendations. This report also describes airport categorization and channelization methodologies. The purposes of the airport categorization task were (1) to facilitate initial AeroMACS architecture designs and enable budgetary projections by creating a set of airport categories based on common airport characteristics and design objectives, and (2) to offer high-level guidance to potential AeroMACS technology and policy development sponsors and service providers. A channelization plan methodology was developed because a common global methodology is needed to assure seamless interoperability among diverse AeroMACS services potentially supplied by multiple service providers.

Stationary nonimaging lenses for solar concentration.

Science.gov (United States)

Kotsidas, Panagiotis; Chatzi, Eleni; Modi, Vijay

2010-09-20

A novel approach for the design of refractive lenses is presented, where the lens is mounted on a stationary aperture and the Sun is tracked by a moving solar cell. The purpose of this work is to design a quasi-stationary concentrator by replacing the two-axis tracking of the Sun with internal motion of the miniaturized solar cell inside the module. Families of lenses are designed with a variation of the simultaneous multiple surface technique in which the sawtooth genetic algorithm is implemented to optimize the geometric variables of the optic in order to produce high fluxes for a range of incidence angles. Finally, we show examples of the technique for lenses with 60° and 30° acceptance half-angles, with low to medium attainable concentrations.

Characterization of the radon source in North-Central Florida. Final report part 1 -- Final project report; Final report part 2 -- Technical report

International Nuclear Information System (INIS)

1997-01-01

This report contains two separate parts: Characterization of the Radon Source in North-Central Florida (final report part 1 -- final project report); and Characterization of the Radon Source in North-Central Florida (technical report). The objectives were to characterize the radon 222 source in a region having a demonstrated elevated indoor radon potential and having geology, lithology, and climate that are different from those in other regions of the U.S. where radon is being studied. Radon availability and transport in this region were described. Approaches for predicting the radon potential of lands in this region were developed

Final Focus Systems in Linear Colliders

International Nuclear Information System (INIS)

Raubenheimer, Tor

1998-01-01

In colliding beam facilities, the ''final focus system'' must demagnify the beams to attain the very small spot sizes required at the interaction points. The first final focus system with local chromatic correction was developed for the Stanford Linear Collider where very large demagnifications were desired. This same conceptual design has been adopted by all the future linear collider designs as well as the SuperConducting Supercollider, the Stanford and KEK B-Factories, and the proposed Muon Collider. In this paper, the over-all layout, physics constraints, and optimization techniques relevant to the design of final focus systems for high-energy electron-positron linear colliders are reviewed. Finally, advanced concepts to avoid some of the limitations of these systems are discussed

75 FR 81564 - Certain Non-Frozen Apple Juice Concentrate From the People's Republic of China: Final Results of...

Science.gov (United States)

2010-12-28

... DEPARTMENT OF COMMERCE International Trade Administration [A-570-855] Certain Non-Frozen Apple... order covering certain non-frozen apple juice concentrate from the People's Republic of China. See...: Certain Non-Frozen Apple Juice Concentrate From the People's Republic of China, 65 FR 35606 (June 5, 2000...

Ultrasonic Concentration in a Line-Driven Cylindrical Tube

Energy Technology Data Exchange (ETDEWEB)

Goddard, Gregory Russ [Portland State Univ., Portland, OR (United States)

2004-01-01

The fractionation of particles from their suspending fluid or noninvasive micromanipulation of particles in suspension has many applications ranging from the recovery of valuable reagents from process flows to the fabrication of microelectromechanical devices. Techniques based on size, density, solubility, or electromagnetic properties exist for fulfilling these needs, but many particles have traits that preclude their use such as small size, neutral buoyancy, or uniform electromagnetic characteristics. While separation by those techniques may not be possible, often compressibility differences exist between the particle and fluid that would allow fractionation by acoustic forces. The potential of acoustic separation is known, but due to inherent difficulties in achieving and maintaining accurate alignment of the transduction system, it is rarely utilized. The objective of this project is to investigate the use of structural excitation as a potentially efficient concentration/fractionation method for particles in suspension. It is demonstrated that structural excitation of a cylindrically symmetric cavity, such as a tube, allows non-invasive, fast, and low power concentration of particles suspended in a fluid. The inherent symmetry of the system eliminates the need for careful alignment inherent in current acoustic concentration devices. Structural excitation distributes the acoustic field throughout the volume of the cavity, which also significantly reduces temperature gradients and acoustic streaming in the fluid; cavitation is no longer an issue. The lowest-order coupled modes of a long cylindrical glass tube and fluid-filled cavity, driven by a line contact, are tuned, via material properties and aspect ratio, to achieve a coupled dipolar vibration of the system, shown to generate efficient concentration of particles to the central axis of the tube. A two dimensional elastodynamic model of the system was developed and subsequently utilized to optimize particle

Tritium concentrations in the atmospheric environment at Rokkasho, Japan before the final testing of the spent nuclear fuel reprocessing plant.

Science.gov (United States)

Akata, Naofumi; Kakiuchi, Hideki; Shima, Nagayoshi; Iyogi, Takashi; Momoshima, Noriyuki; Hisamatsu, Shun'ichi

2011-09-01

This study aimed at obtaining background tritium concentrations in precipitation and air at Rokkasho where the first commercial spent nuclear fuel reprocessing plant in Japan has been under construction. Tritium concentration in monthly precipitation during fiscal years 2001-2005 had a seasonal variation pattern which was high in spring and low in summer. The tritium concentration was higher than that observed at Chiba City as a whole. The seasonal peak concentration at Rokkasho was generally higher than that at Chiba City, while the baseline concentrations of both were similar. The reason for the difference may be the effect of air mass from the Asian continent which is considered to have high tritium concentration. Atmospheric tritium was operationally separated into HTO, HT and hydrocarbon (CH(3)T) fractions, and the samples collected every 3 d-14 d during fiscal year 2005 were analyzed for these fractions. The HTO concentration as radioactivity in water correlated well with that in the precipitation samples. The HT concentration was the highest among the chemical forms analyzed, followed by the HTO and CH(3)T concentrations. The HT and CH(3)T concentrations did not have clear seasonal variation patterns. The HT concentration followed the decline previously reported by Mason and Östlund with an apparent half-life of 4.8 y. The apparent and environmental half-lives of CH(3)T were estimated as 9.2 y and 36.5 y, respectively, by combining the present data with literature data. The Intergovernmental Panel on Climate Change used the atmospheric lifetime of 12 y for CH(4) to estimate global warming in its 2007 report. The longer environmental half-life of CH(3)T suggested its supply from other sources than past nuclear weapon testing in the atmosphere. Copyright © 2011 Elsevier Ltd. All rights reserved.

DEVELOPING SITE-SPECIFIC DERIVED CONCENTRATION GUIDELINE LEVELS FOR MULTIPLE MEDIA AT THE CONNECTICUT YANKEE HADDAM NECK PLANT

International Nuclear Information System (INIS)

Taylor, S.W.; Smith, L.C.; Carr, R.K.; Carson, A.; Darois, E.

2003-01-01

As part of the license termination process, site-specific Derived Concentration Guideline Levels for the Haddam Neck Plant site are developed for soil, groundwater, concrete left standing, and concrete demolished that satisfy the radiological criteria for unrestricted use as defined in 10 CFR 20.1402. Background information on the license termination process and characteristics of the Haddam Neck Plant site are presented. The dose models and associated resident farmer and building occupancy scenarios, applicable pathways, and critical groups developed to establish the Derived Concentration Guideline Levels are described. A parameter assignment process is introduced wherein general population values are used to establish behavioral and metabolic parameters representative of an average member of the critical group, while the uncertainty associated with important physical parameters is considered. A key element of the parameter assignment process is the use of sensitivity analysis to identify the dose sensitive physical parameters and to ensure that such parameters are assigned conservative values. Structuring the parameter assignment process, completing the formal sensitivity analyses, and assigning conservative values to the sensitive physical parameters in a consistent way establishes a calculation framework that lead to Derived Concentration Guideline Levels with a uniform level of conservatism across all media and all radionuclides

Optical analysis and performance evaluation of a solar parabolic dish concentrator

Directory of Open Access Journals (Sweden)

Pavlović Saša R.

2016-01-01

Full Text Available In this study, the optical design of a solar parabolic dish concentrator is presented. The parabolic dish concentrator consists from 11 curvilinear trapezoidal reflective petals made of polymethyl methacrylate with special reflective coating. The dish diameter is equal to 3.8 m and the theoretical focal point distance is 2.26 m. Numerical simulations are made with the commercial software TracePro from Lambda Research, USA, and the final optimum position between absorber and reflector was calculated to 2.075 m; lower than focus distance. This paper presents results for the optimum position and the optimum diameter of the receiver. The decision for selecting these parameters is based on the calculation of the total flux over the flat and corrugated pipe receiver surface; in its central region and in the peripheral region. The simulation results could be useful reference for designing and optimizing of solar parabolic dish concentrators as for as for CFD analysis, heat transfer and fluid flow analysis in corrugated spiral heat absorbers. [Projekat Ministarstva nauke Republike Srbije, br. III42006: Research and development of energy and environmentally highly effective polygeneration systems based on renewable energy resources i br. III45016: Fabrication and characterization of nanophotonic functional structures in biomedicine and informatics

Assessment of quantum dots concentrators for photovoltaic electricity production; Evaluation du potentiel de concentrateurs a quantum dots pour la production d'electricite photovoltaique. Rapport final

Energy Technology Data Exchange (ETDEWEB)

Schueler, A.; Kostro, A.; Huriet, B.

2006-07-01

One of the most promising application of semiconductor nanostructures in the field of photovoltaics might be planar photoluminescent concentrators. Even for diffuse solar radiation, considerable concentration factors might be achieved. Such devices have originally been designed on the basis of organic dyes and might benefit from a considerably improved lifetime when replacing the organic fluorescent substances by inorganic semiconductor nanocrystals, so-called quantum dots. Quantum dot containing nanocomposite thin films are synthesized at EPFL-LESO by a low cost sol-gel process. In order to study the potential of the use of quantum dot solar concentrators in photovoltaic solar energy conversion, reliable computer simulations are needed. A tool for ray tracing simulations of quantum dot solar concentrators has been developed at EPFL-LESO on the basis of Monte-Carlo methods that are applied to polarization-dependent reflection/transmission at interfaces, photon absorption by the semiconductor nanocrystals and photoluminescent re-emission. Together with the knowledge on the optoelectronical properties of suitable photovoltaic cells, such simulations allow to predict the total efficiency of the envisaged concentrating PV systems, and to optimize pane dimensions, photoluminescent emission frequencies, and choice of PV cell types. (author)

Pre-Concentration of Vanadium from Stone Coal by Gravity Using Fine Mineral Spiral

Directory of Open Access Journals (Sweden)

Xin Liu

2016-08-01

Full Text Available Due to the low grade of V2O5 in stone coal, the existing vanadium extraction technologies face challenges in terms of large handling capacity, high acid consumption and production cost. The pre-concentration of vanadium from stone coal before the extraction process is an effective method to reduce cost. In this study, detailed mineral characterization of stone coal was investigated. It has been confirmed that the vanadium mainly occurs in muscovite and illite. A significant demand for an effective pre-concentration process with simple manipulation for discarding quartz and other gangue minerals is expected. Based on the mineralogical study, a new vanadium pre-concentration process using a fine mineral spiral was investigated. The experimental results showed that the separation process, which was comprised of a rougher and scavenger, could efficiently discard quartz, pyrite and apatite. A final concentrate with V2O5 grade of 1.02% and recovery of 89.6% could be obtained, with 26.9% of the raw ore being discarded as final tailings.

Maternal hemoglobin concentration and hematocrit values may affect fetus development by influencing placental angiogenesis.

Science.gov (United States)

Stangret, Aleksandra; Wnuk, Anna; Szewczyk, Grzegorz; Pyzlak, Michał; Szukiewicz, Dariusz

2017-01-01

Vasculogenesis and angiogenesis are crucial for maintaining proper placental perfusion and optimal fetal development. Among other physical and chemical factors, hypoxia is known to stimulate angiogenic processes. Preplacental type of hypoxia is often associated with maternal anemia and is thought to enhance vascularization within the fetoplacental unit. The goal of this study was to establish the correlation between the local expression of vascular endothelial growth factor (VEGF) and placenta growth factor (PlGF) receptors (flt-1, flk-1) with maternal hemoglobin (Hb) concentration, hematocrit (Ht) values and the infant birthweight. In total, 43 specimens of term placentas obtained from normal course pregnancies delivered at term were included in the study. The expression of flt-1 and flk-1 receptors was analyzed by immunohistochemical staining. Vascular/extravascular tissular index (V/EVTI) was measured by assessing a total vascular area. Nonparametric Mann-Whitney U-test and Spearman's rank correlation were used to compare the various parameters and their differences between the groups. Among the patients with low Hb concentration, nearly 2-fold greater expression of the flt-1 receptor was positively correlated with infants birthweight (p = 0.028). Increased placental vascular density (increased flt-1 expression), during a physiological course of gestation, may be an adaptive response to lowered maternal Hb concentration and Ht values encountered during pregnancy.

Characterize and Model Final Waste Formulations and Offgas Solids from Thermal Treatment Processes - FY-98 Final Report for LDRD 2349

Energy Technology Data Exchange (ETDEWEB)

Kessinger, Glen Frank; Nelson, Lee Orville; Grandy, Jon Drue; Zuck, Larry Douglas; Kong, Peter Chuen Sun; Anderson, Gail

1999-08-01

The purpose of LDRD #2349, Characterize and Model Final Waste Formulations and Offgas Solids from Thermal Treatment Processes, was to develop a set of tools that would allow the user to, based on the chemical composition of a waste stream to be immobilized, predict the durability (leach behavior) of the final waste form and the phase assemblages present in the final waste form. The objectives of the project were: • investigation, testing and selection of thermochemical code • development of auxiliary thermochemical database • synthesis of materials for leach testing • collection of leach data • using leach data for leach model development • thermochemical modeling The progress toward completion of these objectives and a discussion of work that needs to be completed to arrive at a logical finishing point for this project will be presented.

Systems study 'Alternative Entsorgung'. Final report. Technical annex 10

International Nuclear Information System (INIS)

Hartje, B.; Kronschnabel, H.; Mueller, W.F.W.

1984-01-01

There is an investigation whether accessibility can be produced to fuel elements stored in a salt mine. All solutions of the problem were followed up until the technically best one was found. Two conditions must be fulfilled for access to the final storage barrel: - There must be a climate which is suitable for people. The Mining Order is the basis for this. - The pit building must be fixed, in the convergence in the salt mine should not lead to it becoming impossible to reach part of the mine. Due to heat-producing waste, rock temperatures are caused in the salt mine, in which mining is no longer possible. Building on the idea of cooling the whole final storage area using concentric sections, the amount of heat to be removal was first estimated. Cooling of the whole final storage area proved to be technically unjustifiable and uninteresting at present. (orig./HP) [de

Multi-Generation Concentrating Solar-Hydrogen Power System for Sustainable Rural Development

Energy Technology Data Exchange (ETDEWEB)

Krothapalli, A.; Greska, B.

2007-07-01

This paper describes an energy system that is designed to meet the demands of rural populations that currently have no access to grid-connected electricity. Besides electricity, it is well recognized that rural populations need at least a centralized refrigeration system for storage of medicines and other emergency supplies, as well as safe drinking water. Here we propose a district system that will employ a multi-generation concentrated solar power (CSP) system that will generate electricity and supply the heat needed for both absorption refrigeration and membrane distillation (MD) water purification. The electricity will be used to generate hydrogen through highly efficient water electrolysis and individual households can use the hydrogen for generating electricity, via affordable proton exchange membrane (PEM) fuel cells, and as a fuel for cooking. The multi-generation system is being developed such that its components will be easy to manufacture and maintain. As a result, these components will be less efficient than their typical counterparts but their low cost-to-efficiency ratio will allow for us to meet our installation cost goal of $1/Watt for the entire system. The objective of this paper is to introduce the system concept and discuss the system components that are currently under development. (auth)

Steel-SiC Metal Matrix Composite Development. Final report

International Nuclear Information System (INIS)

Smith, Don D.

2005-01-01

One of the key materials challenges for Generation IV reactor technology is to improve the strength and resistance to corrosion and radiation damage in the metal cladding of the fuel pins during high-temperature operation. Various candidate Gen IV designs call for increasing core temperature to improve efficiency and facilitate hydrogen production, operation with molten lead moderator to use fast neutrons. Fuel pin lifetime against swelling and fracture is a significant limit in both respects. The goal of this project is to develop a method for fabricating SiC-reinforced high-strength steel. We are developing a metal-matrix composite (MMC) in which SiC fibers are be embedded within a metal matrix of steel, with adequate interfacial bonding to deliver the full benefit of the tensile strength of the SiC fibers in the composite. In the context of the mission of the SBIR program, this Phase I grant has been successful. The development of a means to attain interfacial bonding between metal and ceramic has been a pacing challenge in materials science and technology for a century. It entails matching or grading of thermal expansion across the interface and attaining a graded chemical composition so that impurities do not concentrate at the boundary to create a slip layer. To date these challenges have been solved in only a modest number of pairings of compatible materials, e.g. Kovar and glass, titanium and ceramic, and aluminum and ceramic. The latter two cases have given rise to the only presently available MMC materials, developed for aerospace applications. Those materials have been possible because the matrix metal is highly reactive at elevated temperature so that graded composition and intimate bonding happens naturally at the fiber-matrix interface. For metals that are not highly reactive at processing temperature, however, successful bonding is much more difficult. Recent success has been made with copper MMCs for cooling channels in first-wall designs for fusion

Cost effective manufacturing of the SEA 10X concentrator array. Final subcontract report, 9 January 1991--April 1991

Energy Technology Data Exchange (ETDEWEB)

Kaminar, N.; McEntee, J.; Curchod, D. [Solar Engineering Applications Corp., San Jose, CA (US)

1991-11-01

This report describes a low-cost, mass-producible 10X concentrator system that has been claimed to produce electricity at $0.04/kWh. It details changes in manufacturing techniques that could produce a concentrator system at a selling price of $0.71/W. (A simple design and a minimum number of parts and manufacturing steps reduced production costs.) Present production techniques, changes to improve these techniques, impediments to changes, and solutions to the impediments are described. This 10X concentrator system uses available components and manufacturing processes and one-sun solar cells in conjunction with inexpensive plastic lenses to generate about eight times the amount of electricity normally produced by these cells.

A comprehensive program to develop correlations for physical properties of kraft black liquor. Final report

Energy Technology Data Exchange (ETDEWEB)

Fricke, A.L.; Zaman, A.A.; Stoy, M.O.; Schmidl, G.W.; Dong, D.J.; Speck, B.

1998-04-01

A wide variety of experimental techniques have been used in this work, and many of these have been developed completely or improved significantly in the course of the research done during this program. Therefore, it is appropriate to describe these techniques in detail as a reference for future workers so that the techniques can be used in future work with little additional effort or so that the results reported from this program can be compared better with future results from other work. In many cases, the techniques described are for specific analytical instruments. It is recognized that these may be superseded by future developments and improvements in instrumentation if a complete description of techniques used successfully in the past on other instrumentation is available. The total pulping and liquor preparation research work performed included chip and white liquor preparation, digestion, pulp washing, liquor and wash recovery, liquor sampling, weak liquor concentration in two steps to about 45--50% solids with an intermediate soap skimming at about 140F and 27--30% solids, determination of pulp yield and Kappa number, determination of total liquor solids, and a check on the total material balance for pulping. All other research was performed either on a sample of the weak black liquor (the combined black liquor and washes from the digester) or on the skimmed liquor that had been concentrated.

Post-embriononic development of Chrysomya putoria(Diptera: Calliphoridae on a diet containing ampicillin in different concentrations

Directory of Open Access Journals (Sweden)

ADRIANA C.P. FERRAZ

2016-03-01

Full Text Available Here we evaluate the effects of different concentrations of the antibiotic ampicillin on the growth and development of Chrysomya putoria. Third-generation, first instar larvae (L1 reared on 60 grams of homogenate+agar 65% were treated with ampicillin sodium. The experiment consisted of four replicates (40 larvae/replicate of each antibiotic concentration tested (T1: 466µg/mL ; T2: 81.33 mg/mL and T3: 166.66mg/mL and a T4: control. The body mass of the mature larvae, after they abandoned the diet, were recorded in batches of five. The variation between the mean body mass of larvae and the duration of larval and pupal stages, and overall duration of the development, viability and normal rates were analyzed by ANOVA. There were no significant differences between the four treatments in the following parameters: body mass of larvae that discontinued the diet as well as the duration of larval, pupal, and total development. The sex ratios found in the four treatments did not differ from those expected. Normality rates were 100% for all treatments. There were no significant differences between treatments for larval and overall viability, but pupal viability differed significantly between T1 and the control, T1 and T2, and between the control and T3. The antibiotic did not appear to significantly alter the development of C. putoria.

The recovery of a concentrate of tin and tungsten from ore mined at Van Roois Vley

International Nuclear Information System (INIS)

Guest, R.N.

1985-01-01

Concentration tests using gravity separation, flotation, and magnetic separation showed that it is possible for the high-grade ore mined at Van Roois Vley to be upgraded to a concentrate containing 61 per cent Sn-Wo 3 at a recovery of about 80 per cent, and for the low-grade ore to be upgraded to 53 per cent Sn-WO 3 at the same recovery. However, it is suggested that, under normal mining conditions and with large-scale mining equipment, less fines would be produced and this should lead to an increase in grade and recovery. Mineralogical examinations showed that intermediate fractions produced by tabling contained very few locked particles, and that the grade of the final concentrate on a full-scale plant would probably be higher than that obtained with laboratory equipment. Molybdenite could be a valuable byproduct, but flotation tests of gravity concentrates for selective recovery of the mineral gave variable results. Flotation tests for the removal of fluorspar from the final concentrate were unsuccessful

Measurements in Concentrated Sun using a Remote Controlled Robot

Directory of Open Access Journals (Sweden)

Dan Floroian

2013-04-01

Full Text Available Nowdays, using the concentrated sunlight is a big issue because the amount of energy is very high and the light is concentrated in a very small area. The main problem in this situation is the heating, and in order to make safe measurements a remote controlled robot is needed. After that, a remote controlled robot will assume the duty of protect the measured sample and to expose it for a precise time to the concentrated sun in order to reduce heating of the sample. For easy operating, and for automatize the process, all the duties, starting with initial conditions, continuing with triggering the measurements, and conditioning the signals and finalizing with data saving must be assured by the robot.

DEVELOPING FINAL COURSE MONOGRAPHS USING A TEAM-BASED LEARNING METHODOLOGY

Directory of Open Access Journals (Sweden)

Ani Mari Hartz

2016-04-01

Full Text Available This article describes an experience with the Team-Based Learning (TBL methodology in courses designed to support the planning and execution of final course monographs. It contains both professors’ and students’ perceptions, through observation and assessment. A qualitative approach using observation techniques and desk research was used in conjunction with a quantitative approach based on a questionnaire. The sample consisted of 49 students from a higher education institution, 27 of them in a Communication Course and the remaining 22 in a Business Administration course. Qualitative data analysis was performed through simple categorization with back-defined categories, while the quantitative data analysis employed descriptive statistics and cluster analysis using Minitab 17.1 software. The main findings include the identification of: three student profiles (designated as traditional, collaborative and practical; a preference for guidance and feedback from the professor rather than other students; and a need for a professor-led closing discussion when applying the TBL method. As regards the main benefits to students, they recognized that discussion in groups allowed them to realize how much they really know about the subject studied. Finally, most students seemed to like the TBL approach.

Effect of borate concentration on solidification of radioactive wastes by different cements

International Nuclear Information System (INIS)

Sun Qina; Li Junfeng; Wang Jianlong

2011-01-01

Highlights: → The effect of borate on cementation of radioactive borate evaporator concentrates by sulfoaluminate cement (SAC) and Portland cement (PC) was compared. → The X-ray diffraction (XRD) revealed that borate did not interfere with the formation of main hydration products of SAC and PC. → Borate, in the form of B(OH) 4- , incorporated in ettringite as solid solution phase. - Abstract: To investigate the effect of borate on the cementation of radioactive evaporator concentrates, and to provide more data for solidification formula optimization, the simulated borate evaporator concentrates with different borate concentrations (as B) and Na/B ratio (molar ratio) were solidified by sulfoaluminate cement (SAC) and Portland cement (PC), with addition of Ca(OH) 2 , zeolite and accelerator or water reducer. The hydration products of solidified matrices were characterized by X-ray diffraction (XRD). The experimental results showed that borate retarded the cement setting for both SAC and PC formulas, and the final setting time prolonged with decrease of Na/B ratio. Borate could enhance the fluidity of the cement mixture. The 28 d compressive strengths of the solidified matrices for both SAC and PC formulas decreased with increase of borate concentration. The XRD patterns suggested that, in the matrices maintained for 28 d, borate did not interfere with the formation of main hydration products of SAC and PC. Borate, in the form of B(OH) 4- , incorporated in ettringite (3CaO.Al 2 O 3 .3CaSO 4 .32H 2 O) as solid solution phase. The formula of SAC and PC developed in this study was effective for cementation of the simulated borate evaporator concentrates. However further optimization was required to reduce retarding effect of higher borate concentrations and to extend the practical feasibility for actual evaporator concentrates.

Complex concentrate pretreatment

International Nuclear Information System (INIS)

Lokken, R.O.; Scheele, R.D.; Strachan, D.M.; Toste, A.P.

1991-03-01

After removal of the transuranics (TRU) by the TRUEX process, complex concentrate waste will be grouted for final storage. The purpose of this project, conducted at the Pacific Northwest Laboratory, is to support a future decision to grout the complexant waste without destruction of the organic contents. It has been demonstrated that grouts with acceptable parameters for the Transportable Grout Facility can be made using actual waste. The acceptability of these grouts from a regulatory view seems to be less of a problem than previously. None of the organics found in the waste have been found on the EPA hazardous chemicals list. Two potential problems with the processing of the complex concentrate wastes were identified during the use of the TRUEX process on samples of several milliliters. One was the amount of foam that is generated during acid addition to the alkaline waste. Some of this foam appears to be of a waxy nature but does redissolve when the waste is strongly acid. The second potential problem is that noticeable amounts of NO x gases are generated. No quantitative measure of the NO x gas generation was made. The problem relates to processing the waste in B-plant where there are no facilities to handle NO x gases. 5 refs., 4 figs., 4 tabs

Novel Apparatus for the Real-Time Quantification of Dissolved Gas Concentrations and Isotope Ratios

Science.gov (United States)

Gupta, M.; Leen, J.; Baer, D. S.; Owano, T. G.; Liem, J.

2013-12-01

Measurements of dissolved gases and their isotopic composition are critical in studying a variety of phenomena, including underwater greenhouse gas generation, air-surface exchange, and pollution migration. These studies typically involve obtaining water samples from streams, lakes, or ocean water and transporting them to a laboratory, where they are degased. The gases obtained are then generally measured using gas chromatography and isotope ratio mass spectrometry for concentrations and isotope ratios, respectively. This conventional, off-line methodology is time consuming, significantly limits the number of the samples that can be measured and thus severely inhibits detailed spatial and temporal mapping of gas concentrations and isotope ratios. In this work, we describe the development of a new membrane-based degassing device that interfaces directly to Los Gatos Research (cavity enhanced laser absorption or Off-Axis ICOS) gas analyzers (cavity enhanced laser absorption or Off-Axis ICOS analyzers) to create an autonomous system that can continuously and quickly measure concentrations and isotope ratios of dissolved gases in real time in the field. By accurately controlling the water flow rate through the membrane degasser, gas pressure on the outside of the membrane, and water pressure on the inside of the membrane, the system is able to generate precise and highly reproducible results. Moreover, by accurately measuring the gas flow rates in and out of the degasser, the gas-phase concentrations (ppm) could be converted into dissolved gas concentrations (nM). We will present detailed laboratory test data that quantifies the linearity, precision, and dynamic range of the system for the concentrations and isotope ratios of dissolved methane, carbon dioxide, and nitrous oxide. By interfacing the degassing device to a novel cavity-enhanced spectrometer (developed by LGR), preliminary data will also be presented for dissolved volatile organics (VOC) and other

2006 Long Range Development Plan Final Environmental ImpactReport

Energy Technology Data Exchange (ETDEWEB)

Philliber, Jeff

2007-01-22

This environmental impact report (EIR) has been prepared pursuant to the applicable provisions of the California Environmental Quality Act (CEQA) and its implementing guidelines (CEQA Guidelines), and the Amended University of California Procedures for Implementation of the California Environmental Quality Act (UC CEQA Procedures). The University of California (UC or the University) is the lead agency for this EIR, which examines the overall effects of implementation of the proposed 2006 Long Range Development Plan (LRDP; also referred to herein as the 'project' for purposes of CEQA) for Lawrence Berkeley National Laboratory (LBNL; also referred to as 'Berkeley Lab,' 'the Laboratory,' or 'the Lab' in this document). An LRDP is a land use plan that guides overall development of a site. The Lab serves as a special research campus operated by the University employees, but it is owned and financed by the federal government and as such it is distinct from the UC-owned Berkeley Campus. As a campus operated by the University of California, the Laboratory is required to prepare an EIR for an LRDP when one is prepared or updated pursuant to Public Resources Code Section 21080.09. The adoption of an LRDP does not constitute a commitment to, or final decision to implement, any specific project, construction schedule, or funding priority. Rather, the proposed 2006 LRDP describes an entire development program of approximately 980,000 gross square feet of new research and support space construction and 320,000 gross square feet of demolition of existing facilities, for a total of approximately 660,000 gross square feet of net new occupiable space for the site through 2025. Specific projects will undergo CEQA review at the time proposed to determine what, if any, additional review is necessary prior to approval. As described in Section 1.4.2, below, and in Chapter 3 of this EIR (the Project Description), the size of the project has been

Innovative Technology Development Program. Final summary report

International Nuclear Information System (INIS)

Beller, J.

1995-08-01

Through the Office of Technology Development (OTD), the U.S. Department of Energy (DOE) has initiated a national applied research, development, demonstration, testing, and evaluation program, whose goal has been to resolve the major technical issues and rapidly advance technologies for environmental restoration and waste management. The Innovative Technology Development (ITD) Program was established as a part of the DOE, Research, Development, Demonstration, Testing, and Evaluation (RDDT ampersand E) Program. The plan is part of the DOE's program to restore sites impacted by weapons production and to upgrade future waste management operations. On July 10, 1990, DOE issued a Program Research and Development Announcement (PRDA) through the Idaho Operations Office to solicit private sector help in developing innovative technologies to support DOE's clean-up goals. This report presents summaries of each of the seven projects, which developed and tested the technologies proposed by the seven private contractors selected through the PRDA process

Final disposal of radioactive wastes

Energy Technology Data Exchange (ETDEWEB)

Kroebel, R [Kernforschungszentrum Karlsruhe G.m.b.H. (Germany, F.R.). Projekt Wiederaufarbeitung und Abfallbehandlung; Krause, H [Kernforschungszentrum Karlsruhe G.m.b.H. (Germany, F.R.). Abt. zur Behandlung Radioaktiver Abfaelle

1978-08-01

This paper discusses the final disposal possibilities for radioactive wastes in the Federal Republic of Germany and the related questions of waste conditioning, storage methods and safety. The programs in progress in neighbouring CEC countries and in the USA are also mentioned briefly. The autors conclude that the existing final disposal possibilities are sufficiently well known and safe, but that they could be improved still further by future development work. The residual hazard potential of radioactive wastes from fuel reprocessing after about 1000 years of storage is lower that of known inorganic core deposits.

Estimation of the residual bromine concentration after disinfection of cooling water by statistical evaluation.

Science.gov (United States)

Megalopoulos, Fivos A; Ochsenkuehn-Petropoulou, Maria T

2015-01-01

A statistical model based on multiple linear regression is developed, to estimate the bromine residual that can be expected after the bromination of cooling water. Make-up water sampled from a power plant in the Greek territory was used for the creation of the various cooling water matrices under investigation. The amount of bromine fed to the circuit, as well as other important operational parameters such as concentration at the cooling tower, temperature, organic load and contact time are taken as the independent variables. It is found that the highest contribution to the model's predictive ability comes from cooling water's organic load concentration, followed by the amount of bromine fed to the circuit, the water's mean temperature, the duration of the bromination period and finally its conductivity. Comparison of the model results with the experimental data confirms its ability to predict residual bromine given specific bromination conditions.

Separation, fractionation, concentration and drying of food products: Final report, March 4, 1987--March 31, 1988

Energy Technology Data Exchange (ETDEWEB)

Merlo, C.A.; Rose, W.W.; Pedersen, L.D.; Brewbaker, P.L.

1988-03-01

This project studied energy efficient processes for separation, fractionation, concentration, drying, and recombination of food products, in order to reduce energy requirements for processing, preservation, and transportation. The project had three phases. In the laboratory-scale phase, results of which are summarized in this report, tomato puree was separated by three methods: conventional vacuum filtration, centrifugation, and crossflow microfiltration to produce pulp and serum. Three methods of recombination were examined: homogenizing, stomacher blending, and static (in-line) mixing. Satisfactory recombined purees were obtained. In addition, after centrifugation, the pulp was rinsed producing rinsed-pulp, and the rinse water was added to the serum producing rinse/serum. The rinse/serum was concentrated by evaporation. This was recombined with the rinsed-pulp and water producing satisfactory puree. 11 refs., 18 figs., 18 tabs.

Concentrated loads on concrete

DEFF Research Database (Denmark)

Lorenzen, Karen Grøndahl; Nielsen, Mogens Peter

1997-01-01

This report deals with concentrated loads on concrete.A new upper bound solution in the axisymmetrical case of a point load in the center of the end face of a cylinder is developed.Based on previous work dealing with failure mechanisms and upper bound solutions, new approximate formulas are devel......This report deals with concentrated loads on concrete.A new upper bound solution in the axisymmetrical case of a point load in the center of the end face of a cylinder is developed.Based on previous work dealing with failure mechanisms and upper bound solutions, new approximate formulas...

The effect of minimal concentration of ethylene glycol (EG) combined with polyvinylpyrrolidone (PVP) on mouse oocyte survival and subsequent embryonic development following vitrification.

Science.gov (United States)

Wang, Yao; Okitsu, Osamu; Zhao, Xiao-Ming; Sun, Yun; Di, Wen; Chian, Ri-Cheng

2014-01-01

Vitrification techniques employ a relatively high concentration of cryoprotectant in vitrification solutions. Exposure of oocytes to high concentrations of cryoprotectant is known to damage the oocytes via both cytotoxic and osmotic effects. Therefore, the key to successful vitrification of oocytes is to strike a balance between the usage of minimal concentration of cryoprotectant without compromising their cryoprotective actions. The minimal concentration of ethylene glycol (EG) on mouse oocyte survival and subsequent embryonic development was evaluated following vitrification-warming and parthenogenetic activation. Polyvinylpyrrolidone (PVP) combined with EG on mouse oocyte survival and subsequent embryonic development as well as morphology of the spindle and chromosome alignment were also evaluated. Vitrification system was adapted with JY Straw and the cooling rate was approximately 442-500 °C/min. In contrast, the warming rate was approximately 2,210-2,652 °C/min. Survival rate of oocytes increased significantly when 15 % EG was combined with 2 % PVP in vitrification solution (VS). The effect of combination of EG and PVP was not significant when the concentration of EG was 20 % and higher. Although there were no significant differences in embryonic development, the percentage of abnormal spindle and chromosome alignment was significantly higher in the oocytes without 2 % PVP in VS. Our data provide a proof of principle for oocyte vitrification that may not require a high concentration of cryoprotectant. There are synergic effects of EG combined with PVP for oocyte vitrification, which may provide important information to the field in developing less cytotoxic VS.

Photovoltaic static concentrator analysis

Science.gov (United States)

Almonacid, G.; Luque, A.; Molledo, A. G.

1984-12-01

Ray tracing is the basis of the present analysis of truncated bifacial compound parabolic concentrators filled with a dielectric substance, which are of interest in photovoltaic applications where the bifacial cells allow higher static concentrations to be achieved. Among the figures of merit for this type of concentrator, the directional intercept factor plays a major role and is defined as the ratio of the power of the collector to that at the entry aperture, in a lossless concentrator illuminated by light arriving from a given direction. A procedure for measuring outdoor, full size panels has been developed, and a correction method for avoiding the effect of unwanted diffuse radiation during the measurements is presented.

Developing maintainability for fusion power systems. Final report

Energy Technology Data Exchange (ETDEWEB)

Zahn, H.S.; Mantz, H.C.; Curtis, C.T.; Buchheit, R.J.; Green, W.M.; Zuckerman, D.S.

1979-11-01

The overall purpose of the study is to identify design features of fusion power reactors which contribute to the achievement of high levels of maintainability. Previous phases evaluated several commercial tokamak reactor design concepts. This final phase compares the maintainability of a tandem mirror reactor (TMR) commercial conceptual design with the most maintainable tokamak concept selected from earlier work. A series of maintainability design guidelines and desirable TMR design features are defined. The effects of scheduled and unscheduled maintenance for most of the reactor subsystems are defined. The comparison of the TMR and tokamak reactor maintenance costs and availabilities show that both reactors have similar costs for scheduled maintenance at 19.4 and 20.8 million dollars annually and similar scheduled downtime availability impacts, achieving approximate availabilities of 79% at optimized maintenance intervals and cost of electricity.

Developing maintainability for fusion power systems. Final report

International Nuclear Information System (INIS)

Zahn, H.S.; Mantz, H.C.; Curtis, C.T.; Buchheit, R.J.; Green, W.M.; Zuckerman, D.S.

1979-11-01

The overall purpose of the study is to identify design features of fusion power reactors which contribute to the achievement of high levels of maintainability. Previous phases evaluated several commercial tokamak reactor design concepts. This final phase compares the maintainability of a tandem mirror reactor (TMR) commercial conceptual design with the most maintainable tokamak concept selected from earlier work. A series of maintainability design guidelines and desirable TMR design features are defined. The effects of scheduled and unscheduled maintenance for most of the reactor subsystems are defined. The comparison of the TMR and tokamak reactor maintenance costs and availabilities show that both reactors have similar costs for scheduled maintenance at 19.4 and 20.8 million dollars annually and similar scheduled downtime availability impacts, achieving approximate availabilities of 79% at optimized maintenance intervals and cost of electricity

Laboratory studies conducted for the development of a plant to concentrate the radioactive waste from tritiated water

International Nuclear Information System (INIS)

Bornea, Anisia; Zamfirache, Marius; Stefanescu, Ioan; Vasut, Felicia; Soare, Amalia

2010-01-01

The Cernavoda Nuclear Power Plant is the biggest operational source of tritium, in Europe and one of the most important in the world. The recovery of tritium from the moderator of operating Candu reactors and from the reactors to operate, represents a good opportunity for Romania to be involved in international collaboration programs in the field of nuclear fusion. Our interest is especially focussed on tritiated waste water with low activity resulted from the maintenance work performed on reactors with the purpose of reducing their volume and their reprocessing. The system presented in this work is based on the catalytic isotopic exchange and molecular dissociation CECE (Combined Electrolysis Catalytic Exchange). It has been noticed a growing interest regarding the electrolysers having polymer membranes as electrolyte SPM (solid polymer membrane). The advantage of using polymer membranes consists in the fact that membranes are actually the electrolyte and performs in the same time hydrogen and its isotopes separation. The present paper presents a conceptual design scheme for a tritium concentration system resulted from the tritiated waste water. This conceptual design represented the basis for the development of the installation for the tritiated waste water concentration, and the experiments to be performed will represent a support for promoting this technology. For designing the system and for analysing its functionality, a theoretical model for calculating tritium separation and concentration, has been developed.

Smart roadside initiative : final report.

Science.gov (United States)

2015-09-01

This is the Final Report for the Smart Roadside Initiative (SRI) prototype system deployment project. The SRI prototype was implemented at weigh stations in Grass Lake, Michigan and West Friendship, Maryland. The prototype was developed to integrate ...

Chronological development of element concentrations in grapes during growth and ripeness and during fermentation of must determined by instrumental neutron-activation analyses

Energy Technology Data Exchange (ETDEWEB)

Feige, Markus; Hampel, Gabriele; Kratz, Jens Volker; Wiehl, Norbert [Mainz Univ. (Germany). Inst. fuer Kernchemie; Koenig, Helmut [Mainz Univ. (Germany). Inst. fuer Mikrobiologie und Weinforschung; Wagner, Andreas [Weingut Wagner, Essenheim (Germany)

2014-07-01

The chronological development of element concentrations during growth and ripeness of grapes described in the literature has only been concerned with the macro elements Mg, K, and Ca. Concentrations of trace elements in must are only described as a snapshot at the end of the ripeness. Therefore, the motivation for the present work was to accompany the growth and the ripening process of grapes successively by systematically determining element concentrations in grapes of Riesling and Cabernet Sauvignon by neutron-activation analyses. While for a number of elements, the concentrations in the grapes increased as a function of grape development (e.g., Na, K, Rb, Al), other concentrations decreased (e.g., Mg, Ca, Mn). These decreases are not only to be attributed to a dilution by an increasing uptake of water during growth, but also by an active transport of the cations out of the berries. Furthermore, the interest focused on the influence of mineral substances on the process of fermentation and on the uptake of trace elements by the yeasts. (orig.)

Chronological development of element concentrations in grapes during growth and ripeness and during fermentation of must determined by instrumental neutron-activation analyses

International Nuclear Information System (INIS)

Feige, Markus; Hampel, Gabriele; Kratz, Jens Volker; Wiehl, Norbert

2014-01-01

The chronological development of element concentrations during growth and ripeness of grapes described in the literature has only been concerned with the macro elements Mg, K, and Ca. Concentrations of trace elements in must are only described as a snapshot at the end of the ripeness. Therefore, the motivation for the present work was to accompany the growth and the ripening process of grapes successively by systematically determining element concentrations in grapes of Riesling and Cabernet Sauvignon by neutron-activation analyses. While for a number of elements, the concentrations in the grapes increased as a function of grape development (e.g., Na, K, Rb, Al), other concentrations decreased (e.g., Mg, Ca, Mn). These decreases are not only to be attributed to a dilution by an increasing uptake of water during growth, but also by an active transport of the cations out of the berries. Furthermore, the interest focused on the influence of mineral substances on the process of fermentation and on the uptake of trace elements by the yeasts. (orig.)

[Serum calcium and phosphorus concentration and alkaline phosphatase activity in healthy children during growth and development].

Science.gov (United States)

Savić, Ljiljana; Savić, Dejan

2008-01-01

Many changes happen during growth and development in an organism as a result of important hormon changes, especially biohumoral ones. These changes make a problem when interpreting biochemical results in pediatric population. The most important changes are intensive calcium and phosphorus metabolic turnover in bone tissue with changes in alkaline phosphatase activity as a result of osteoblast activity. The aim of this study was to follow the serum calcium and phosphorus concentration and alkaline phosphatase activity in children 1-15 years old in different growth and development period and of different sexes and to fortify the influence of growth and development dynamics on biohumoral status in healthy male and female children. We evaluated 117 healthy children of both sexes from 1-15 years of age and divided them into three age groups: 1-5, 6-10 and 11-15 years. We followed the serum calcium and phosphorus concentration and alkaline phosphatase activity in different groups and in different sexes. Our investigation found significantly higher values of serum calcium in boys than in girls with no important changes between the age groups and significantly higher values of serum phosphorus in the youngest age group in all children and in different sexes with no important sex differences. Alkaline phosphatase activity followed the growth spurt and was the biggest in 6-10 years group in girls and in 11-15 years group in boys.

Zachary-Fort Lauderdale pipeline construction and conversion project: final supplement to final environmental impact statement. Docket No. CP74-192

Energy Technology Data Exchange (ETDEWEB)

None

1980-05-01

This Final Supplement to the Final Environmental Impact Statement (Final Supplement) evaluates the economic, engineering, and environmental aspects of newly developed alternatives to an abandonment/conversion project proposed by Florida Gas Transmission Company (Florida Gas). It also updates the staff's previous FEIS and studies revisions to the original proposal. Wherever possible, the staff has adopted portions of its previous FEIS in lieu of reprinting portions of that analysis which require no change. 60 references, 8 figures, 35 tables.

Final Scientific/Technical Report

Energy Technology Data Exchange (ETDEWEB)

Seinfeld, John H. [California Inst. of Technology (CalTech), Pasadena, CA (United States)

2015-08-06

This project addressed the following research need in the Atmospheric System Research (ASR) Science and Program Plan: "Measurements downwind of urban sources of aerosol particles and precursor gases have shown that the mass concentration of secondary organic aerosol (SOA) can be several-fold greater than can be explained on the basis of current model calculations using observed precursor concentrations. ASR will continue conducting laboratory experiments on both gas-phase and aqueous-phase SOA formation to characterize the particle formation and the organic gases that react to form new organic aerosol material on aerosol seeds. ASR will use these experiments to guide the development of comprehensive chemical mechanisms... to guide the development of parameterizations that are simple enough to be applied to aerosol life cycle models."

Report on research and development work 1982 of the Institut fuer Nukleare Entsorgungstechnik

International Nuclear Information System (INIS)

1983-02-01

The R and D work carried out at the Institute of Nuclear Waste Processing during 1982 under the four sections Chemistry, Processing Technology, Final Storage, and Infrastructure and Analysis is reported here. Areas of emphasis were: 1) Development and demonstration of a technical process for embedding highly radioactive solutions of fission products in borosilicate glass blocks, 2) Study of the properties of original glass moulds produced in this process, 3) Solidification of low and medium-active waste concentrates in cement, 4) Separation of actinides and fission products from medium-active waste solutions, 5) Solidification of alpha-containing concentrates in a ceramic matrix and characterization of the products, 6) Demonstration of wet chemical oxidation of combustible wastes containing higher levels of Pu together with the recovery of Pu, 7) Investigation of the release of radionuclides from medium-active waste products by leaching, corrosion, and mechanical or thermal stress, 8) Studies on the development of long-term stable containers suitable for final storage of highly radioactive glass products in salt, 9) Studies on the storage of heat-generating waste in salt, 10) Studies on analytical safety assurance for final storage in geological formations. (orig./RB) [de

Modeling groundwater nitrate concentrations in private wells in Iowa

Science.gov (United States)

Wheeler, David C.; Nolan, Bernard T.; Flory, Abigail R.; DellaValle, Curt T.; Ward, Mary H.

2015-01-01

Contamination of drinking water by nitrate is a growing problem in many agricultural areas of the country. Ingested nitrate can lead to the endogenous formation of N-nitroso compounds, potent carcinogens. We developed a predictive model for nitrate concentrations in private wells in Iowa. Using 34,084 measurements of nitrate in private wells, we trained and tested random forest models to predict log nitrate levels by systematically assessing the predictive performance of 179 variables in 36 thematic groups (well depth, distance to sinkholes, location, land use, soil characteristics, nitrogen inputs, meteorology, and other factors). The final model contained 66 variables in 17 groups. Some of the most important variables were well depth, slope length within 1 km of the well, year of sample, and distance to nearest animal feeding operation. The correlation between observed and estimated nitrate concentrations was excellent in the training set (r-square = 0.77) and was acceptable in the testing set (r-square = 0.38). The random forest model had substantially better predictive performance than a traditional linear regression model or a regression tree. Our model will be used to investigate the association between nitrate levels in drinking water and cancer risk in the Iowa participants of the Agricultural Health Study cohort.

Modeling groundwater nitrate concentrations in private wells in Iowa.

Science.gov (United States)

Wheeler, David C; Nolan, Bernard T; Flory, Abigail R; DellaValle, Curt T; Ward, Mary H

2015-12-01

Contamination of drinking water by nitrate is a growing problem in many agricultural areas of the country. Ingested nitrate can lead to the endogenous formation of N-nitroso compounds, potent carcinogens. We developed a predictive model for nitrate concentrations in private wells in Iowa. Using 34,084 measurements of nitrate in private wells, we trained and tested random forest models to predict log nitrate levels by systematically assessing the predictive performance of 179 variables in 36 thematic groups (well depth, distance to sinkholes, location, land use, soil characteristics, nitrogen inputs, meteorology, and other factors). The final model contained 66 variables in 17 groups. Some of the most important variables were well depth, slope length within 1 km of the well, year of sample, and distance to nearest animal feeding operation. The correlation between observed and estimated nitrate concentrations was excellent in the training set (r-square=0.77) and was acceptable in the testing set (r-square=0.38). The random forest model had substantially better predictive performance than a traditional linear regression model or a regression tree. Our model will be used to investigate the association between nitrate levels in drinking water and cancer risk in the Iowa participants of the Agricultural Health Study cohort. Copyright © 2015 Elsevier B.V. All rights reserved.

The Development of Teacher Perspectives: Final Report.

Science.gov (United States)

Tabachnick, B. Robert; Zeichner, Kenneth M.

This longitudinal study of the development of perspectives toward teaching consists of three major phases: (1) an examination of the impact of the student teaching experience on the development of teacher perspectives; (2) an examination of the continuing development of teacher perspectives during the first year of teaching; and (3) further…

Determination of the radioactive concentration of 137Cs in soil

International Nuclear Information System (INIS)

1987-01-01

According to the latest Hungarian standard valid from January 1987 the activity concentration of 137 Cs in soil is determined based on the measurement of beta disintegration rate following the radiochemical separation of cesium ion. Soil samples are destructed with strong acid. Dissolved cesium is retained selectively by ammonium-molybdo-phosphate in a batch process. The inorganic ion-exchanger is dissoled with concentrated sodium-hydroxide, and, finally, cesium ion is precipitated with hexa-chloro-platinate. In the course of beta detection self-absoprtion of the precipitate must be corrected. (V.N.)

Continued development of modeling tools and theory for rf heating. Final report

International Nuclear Information System (INIS)

Smithe, D.N.

1998-01-01

The work performed during the grant has been reported long before this date, specifically in: (1) the grant's annual performance report for 1991, MRC/WDC-R-277; (2) the published AIP Conference Proceedings number-sign 244, Radio Frequency Power in Plasmas, Charleston, SC 1991, ''Evaluation of Wave Dispersion, Mode-Conversion, and Damping for ECRH with Exact Relativistic Corrections,'' by D.N. Smithe and P.L. Colestock; and (3) an unpublished paper entitled ''Temperature Anisotropy and Rotation Upgrades to the ICRF Modules in SNAP and TRANSP'', presented at the 1992 ICRF Modeling and Theory Workshop, at the Princeton Plasma Physics Laboratory. This final report contains copies of number (1). The specifics of the grant's final months' activities, which to the authors recollection have never been reported to the DOE, are as follows. The original grant, which was to terminate August 15, 1991, was extended without additional funds to October 31, 1992. The primary reason for the extension was to permit attendance at the 1992 ICRF Modeling and Theory Workshop at the Princeton Plasma Physics Laboratory (PPPL), which was finally held August 17--18, 1992, after having been rescheduled several times during the summer of 1992. The body of this report contains copies of the 1991 annual report, which gives detailed discussion of the work accomplished

Individual analysis of creatine kinase concentration in Brazilian elite soccer players

Directory of Open Access Journals (Sweden)

Adriano Lima Alves

2015-04-01

Full Text Available OBJECTIVE: to determine the individual profile of blood concentration of creatine kinase CK in elite soccer players as well as to analyze the CK concentrations in different periods during the Professional Brazilian Championship. METHODS: resting CK of 17 soccer players was evaluated before the competition pre-season and after the matches 36 and 46 hours after the games CKGame for the individual blood CK. The Chi-square test was used to analyze the individual CK during the season. The competitive season was divided into three periods: initial, intermediate and final. The one-way ANOVA with repeated measurements followed by post hoc Student-Newman-Keuls test was used to compare the individual CK of each soccer player in each competitive period. The significance level was set at p<0.05. RESULTS: the highest frequency of individual CK was found in the second quartile 71 observations and the lowest frequency in the first 26 observations and the fourth quartile 40 observations compared to the expected number of 45.8 x2=22.21. CK concentrations were lower in the intermediate mean=66.99% and final mean=60.21% periods than in the initial period mean=89.33%. CONCLUSION: soccer players did not show elevated muscle damage and probably a muscle adaptation occurred in the competition, due to the reduction of CK concentrations observed.

Safeguards for final disposal of spent nuclear fuel. Methods and technologies for the Olkiluoto site

International Nuclear Information System (INIS)

Okko, O.

2003-05-01

The final disposal of the nuclear material shall introduce new safeguards concerns which have not been addressed previously in IAEA safeguards approaches for spent fuel. The encapsulation plant to be built at the site will be the final opportunity for verification of spent fuel assemblies prior to their transfer to the geological repository. Moreover, additional safety and safeguards measures are considered for the underground repository. Integrated safeguards verification systems will also concentrate on environmental monitoring to observe unannounced activities related to possible diversion schemes at the repository site. The final disposal of spent nuclear fuel in geological formation will begin in Finland within 10 years. After the geological site investigations and according to legal decision made in 2001, the final repository of the spent nuclear fuel shall be located at the Olkiluoto site in Eurajoki. The next phase of site investigations contains the construction of an underground facility, called ONKALO, for rock characterisation purposes. The excavation of the ONKALO is scheduled to start in 2004. Later on, the ONKALO may form a part of the final repository. The plans to construct the underground facility for nuclear material signify that the first safeguards measures, e.g. baseline mapping of the site area, need to take prior to the excavation phase. In order to support the development and implementation of the regulatory control of the final disposal programme, STUK established an independent expert group, LOSKA. The group should support the STUK in the development of the technical safeguards requirements, in the implementation of the safeguards and in the evaluation of the plans of the facility operator. This publication includes four background reports produced by this group. The first of these 'NDA verification of spent fuel, monitoring of disposal canisters, interaction of the safeguards and safety issues in the final disposal' describes the new

MHD seed recovery and regeneration, Phase II. Final report

Energy Technology Data Exchange (ETDEWEB)

1994-10-01

This final report summarizes the work performed by the Space and Technology Division of the TRW Space and Electronics Group for the U.S. Department of Energy, Pittsburgh Energy Technology Center for the Econoseed process. This process involves the economical recovery and regeneration of potassium seed used in the MHD channel. The contract period of performance extended from 1987 through 1994 and was divided into two phases. The Phase II test results are the subject of this Final Report. However, the Phase I test results are presented in summary form in Section 2.3 of this Final Report. The Econoseed process involves the treatment of the potassium sulfate in spent MHD seed with an aqueous calcium formate solution in a continuously stirred reactor system to solubilize, as potassium formate, the potassium content of the seed and to precipitate and recover the sulfate as calcium sulfate. The slurry product from this reaction is centrifuged to separate the calcium sulfate and insoluble seed constituents from the potassium formate solution. The dilute solids-free potassium formate solution is then concentrated in an evaporator. The concentrated potassium formate product is a liquid which can be recycled as a spray into the MHD channel. Calcium formate is the seed regenerant used in the Econoseed process. Since calcium formate is produced in the United States in relatively small quantities, a new route to the continuous production of large quantities of calcium formate needed to support an MHD power industry was investigated. This route involves the reaction of carbon monoxide gas with lime solids in an aqueous medium.

Radiometers for radon concentration in air

International Nuclear Information System (INIS)

Bartak, J.; Machaj, B.; Pienkos, J.P.

2002-01-01

Constant grow of science and technology stimulates development of new improved measuring tools. New measuring demand arise also in radon concentration measurements. Varying rock stress and rock cracks influencing radon emanation encouraged research aimed at use of this phenomenon to predict crumps of mine formation among others based on variation of radon emanation. A measuring set was developed in the Institute of Nuclear Chemistry and Technology enabling long term monitoring of radon concentration in mine bore-hole. The set consists probe and probe controller. Detection threshold of the probe is 230 Bq/m 3 . The set can operate in the environment with methane explosion hazard. A radiometer employing Lucas cell as radiation detector for radon concentration in air was also developed its detection threshold is approx. 10 Bq/m 3 . Replaceable Lucas cell of the radiometer allows for measurement of high as well as low radon concentration in short time interval. (author)

Study on calculation models and distribution rules of the radon concentration and its progenies concentration in blind roadway with forced-exhaust ventilation

International Nuclear Information System (INIS)

Ye Yongjun; Wang Liheng; Zhou Xinghuo; Li Xiangyang; Zhong Yongming; Wang Shuyun; Ding Dexin

2014-01-01

The forced-exhaust ventilation is an important way to control the concentration of radon and its progenies in long-distance blind driving roadway. It is of great significance for guiding the design of ventilation and radiation protection to study distribution characteristics of the concentration of radon and its progenies in the wind of roadway adopting the forced-exhaust ventilation. Therefore, according to the decay relationship of radon and its progenies, a simplified mathematical calculation model was built, which relates to the radon activity concentration and the potential alpha concentration of radon progenies. The paper also analyzed the sources of radon and its progenies in the limited space of the blind roadway. Then, based on the turbulence mass transfer theory of ventilation air flow, the paper established mathematical calculation models of distribution characteristics of the radon activity concentration and the potential alpha concentration of radon progenies in blind roadway with forced-exhaust ventilation, respectively. Finally, the paper applied the calculation models to a special blind roadway, and discussed the influence of the ventilation air inflow and the radon exhalation rate of rock wall on the distribution of radon concentration and the potential alpha concentration of radon progenies in the roadway. Meanwhile, some protective measurements were put forward to reduce the radiation dose of worker caused by radon and its progenies in the blind roadway. (authors)

Estimation of daily protein intake based on spot urine urea nitrogen concentration in chronic kidney disease patients.

Science.gov (United States)

Kanno, Hiroko; Kanda, Eiichiro; Sato, Asako; Sakamoto, Kaori; Kanno, Yoshihiko

2016-04-01

Determination of daily protein intake in the management of chronic kidney disease (CKD) requires precision. Inaccuracies in recording dietary intake occur, and estimation from total urea excretion presents hurdles owing to the difficulty of collecting whole urine for 24 h. Spot urine has been used for measuring daily sodium intake and urinary protein excretion. In this cross-sectional study, we investigated whether urea nitrogen (UN) concentration in spot urine can be used to predict daily protein intake instead of the 24-h urine collection in 193 Japanese CKD patients (Stages G1-G5). After patient randomization into 2 datasets for the development and validation of models, bootstrapping was used to develop protein intake estimation models. The parameters for the candidate multivariate regression models were male gender, age, body mass index (BMI), diabetes mellitus, dyslipidemia, proteinuria, estimated glomerular filtration rate, serum albumin level, spot urinary UN and creatinine level, and spot urinary UN/creatinine levels. The final model contained BMI and spot urinary UN level. The final model was selected because of the higher correlation between the predicted and measured protein intakes r = 0.558 (95 % confidence interval 0.400, 0.683), and the smaller distribution of the difference between the measured and predicted protein intakes than those of the other models. The results suggest that UN concentration in spot urine may be used to estimate daily protein intake and that a prediction formula would be useful for nutritional control in CKD patients.

APOLLON. Multi-APprOach for high efficiency integrated and inteLLigent cONcentrating PV modules (Systems). Deliverable 7.10. Publication of environmental LCI dataset

Energy Technology Data Exchange (ETDEWEB)

Olson, C.L. [ECN Solar Energy, Petten (Netherlands)

2013-10-15

This deliverable makes available the life-cycle inventory used to calculate the energy payback time and the carbon footprint of the Apollon final concentrating photovoltaics (CPV) design developed.. The data below relates to one Apollon module. The results are to be published in Environmental Science and Technology, in a paper, 'Sustainability of Materials and Costs of Materials in a Mirror-based Concentrating Photovoltaic System'. Reference is made to the results for the Spectrolab triple junction solar cell in the following two studies: (1) 'Life cycle assessment of high-concentration photovoltaic systems' (Prog. Photovolt: Res. Appl., vol. 21, pp. 379-388, 2013), and (2) 'Life Cycle Analysis of Two New Concentrator PV Systems', in 23rd European Photovoltaic Solar Energy Conference, Valencia, Spain, 2008.

Specified radioactive waste final disposal act

International Nuclear Information System (INIS)

Yasui, Masaya

2001-01-01

Radioactive wastes must be finally and safely disposed far from human activities. Disposal act is a long-range task and needs to be understood and accepted by public for site selection. This paper explains basic policy of Japanese Government for final disposal act of specified radioactive wastes, examination for site selection guidelines to promote residential understanding, general concept of multi-barrier system for isolating the specific radioactive wastes, and research and technical development for radioactive waste management. (S. Ohno)

ERYA (bulk)-finally available and ERYA profile-final adjustments

International Nuclear Information System (INIS)

Pedro de Jesus, A.

2014-01-01

Full text: It was announced and shown that the ERYA-bulk code for analysis of in-depth homogeneous samples is now available and may be downloaded from a web site, where a manual is available to explain how to use it. A tutorial on the code’s interface and capabilities was shown, namely the capability of calculating simultaneously the mass concentration of an arbitrary number of elements in a homogeneous sample (any thickness), with the additional capability of fitting the sample matrix composition. This may be done by using as an initial estimate either the results from another analytical technique such as PIXE (usually used as a complementary technique) or with prior knowledge of the main chemical composition. Regarding the development of a routine to perform depth profile measurements, the main aspects of what was already done were presented: 1. the routine was developed to be used interactively, as RUMP, or SigmaNRA, by comparing the calculated and experimental results for each concentration distribution given by the user; 2. the routine uses a division of the target into layers (as in the case of ERYA bulk) but within each layer the projectiles have an energy distribution and not a single energy value (as in the case of ERYA bulk); this implies that depth together with average energy must be calculated for every layer; 3. the energy distribution takes into account Beam Energy Resolution, Beam Energy Straggling and Doppler Broadening; 4. in order to implement energy straggling calculations, Landau, Vavilov and Gaussian distributions are used; 5. the resonant cross section function may be replaced by an ideal Breit-Wigner function; further efforts to implement the code to use resonance strengths are being developed; 6. the concentration may be given for any number of discrete layers or as a depth dependent continuous function. This profile routine is already working with a user-friendly interface, which was also presented. Further tests and improvements are

Atmospheric relative concentrations in building wakes

International Nuclear Information System (INIS)

Ramsdell, J.V. Jr.; Simonen, C.A.; Smyth, S.B.

1995-05-01

This report documents the ARCON95 computer code developed for the U.S. Nuclear Regulatory Commission Office of Nuclear Regulatory Research for use in control room habitability assessments. The document includes a user's guide to the code, a description of the technical basis for the code, and a programmer's guide to the code. The ARCON95 code uses hourly meteorological data and recently developed methods for estimating dispersion in the vicinity of buildings to calculate relative concentrations at control room air intakes that would be exceeded no more five percent of the time. These concentrations are calculated for averaging periods ranging from one hour to 30 days in duration. Relative concentrations calculated by ARCON95 are significantly lower than concentrations calculated using the currently accepted procedure when winds are less than two meters per second. For higher wind speeds, ARCON95 calculates about the same concentrations as the current procedure

Hydrothermal industrialization: direct heat development. Final report

Energy Technology Data Exchange (ETDEWEB)

1982-05-01

A description of hydrothermal resources suitable for direct applications, their associated temperatures, geographic distribution and developable capacity are given. An overview of the hydrothermal direct-heat development infrastructure is presented. Development activity is highlighted by examining known and planned geothermal direct-use applications. Underlying assumptions and results for three studies conducted to determine direct-use market penetration of geothermal energy are discussed.

Vacuum drying plant for evaporator concentrates

International Nuclear Information System (INIS)

Benavides, E.

2001-01-01

Volume reduction systems applied to evaporator concentrates in PWR and BWR save a significant amount of drums. The concentration to dry product is a technique that reaches the maximum volume reduction, compared to conventional techniques (cementation, polymerisation). Four Spanish N.P.P. (3 PWR and 1 BWR) have selected ENSA's process by means of fixed ''in drum vacuum drying system''. A 130-litre steel drum is used for drying without any additional requirement except vacuum resistance. This steel drum is introduced into a standard 200-litre drum. Five centimeters concrete shielding cylinder exists between both drums. Final package is classified as 19 GO according to ENRESA's acceptance code (dry waste with 5 cm concrete between 130-l and 200-l drum). The generation of cemented waste in five N.P.P. versus dried waste will be reduced 83%. This reduction will save a considerable amount in disposal costs. (authors)

An Integrated Instrumentation System for Velocity, Concentration and Mass Flow Rate Measurement of Solid Particles Based on Electrostatic and Capacitance Sensors

Directory of Open Access Journals (Sweden)

Jian Li

2015-12-01

Full Text Available The online and continuous measurement of velocity, concentration and mass flow rate of pneumatically conveyed solid particles for the high-efficiency utilization of energy and raw materials has become increasingly significant. In this paper, an integrated instrumentation system for the velocity, concentration and mass flow rate measurement of dense phase pneumatically conveyed solid particles based on electrostatic and capacitance sensorsis developed. The electrostatic sensors are used for particle mean velocity measurement in combination with the cross-correlation technique, while the capacitance sensor with helical surface-plate electrodes, which has relatively homogeneous sensitivity distribution, is employed for the measurement of particle concentration and its capacitance is measured by an electrostatic-immune AC-based circuit. The solid mass flow rate can be further calculated from the measured velocity and concentration. The developed instrumentation system for velocity and concentration measurement is verified and calibrated on a pulley rig and through static experiments, respectively. Finally the system is evaluated with glass beads on a gravity-fed rig. The experimental results demonstrate that the system is capable of the accurate solid mass flow rate measurement, and the relative error is within −3%–8% for glass bead mass flow rates ranging from 0.13 kg/s to 0.9 kg/s.

PV window - Development and demonstrations. Final report

Energy Technology Data Exchange (ETDEWEB)

Haugaard, P.

2011-05-15

Using the results from the EU project RenewTransnet, which focused on the development of a pane with integrated solar cells, the goal of this project is to develop these principles into a window solution. This window solution is targeted to Danish building tradition and architecture. It is expected that an elegant PV-window solution for both new and retrofit buildings is developed during this project, and which appearance can be customized to each building. Based on results from a related projects carried out by Gaia Solar, the window solution will have the potential of being approximately 30% cheaper than similar products on the market. In this project this price reduction is the objective of the development of a window solution. The project team has succeeded in developing a 2-layer PV-window with glass / glass lamination with EVA as foil, which is 35% cheaper than similar products on the market. Since the price for the frame-profile does not differ significantly at market level, the price comparison is made on the basis of the developed PV-pane. The objective of 30 % price reduction in relation to similar products on the market is met. A special production process to the making glass/glass lamination with EVA as foil has been developed, in which a frame is put around the module which intends both to remove the unwanted tension along the edges, and to prevent the significant spillage of EVA from the module under pressure and prevent the invasive bubbles along the edge of module. Since the developed production method for making glass/glass modules with EVA is simple, a further cost reduction will primarily be in a reduction of the price of the cell. The project process has resulted in the development of a product, which due to continuous restrictions in the building regulations, will be very attractive in future buildings. (LN)

Final report on implementation of energy conservation practices training in selected public housing developments

Energy Technology Data Exchange (ETDEWEB)

1991-10-01

This report on the implementation of energy conservation practices training in selected public housing developments represents an initiative of the Research and Education Division, Office of Minority Economic Impact, US Department of Energy. The Office of Minority Economic Impact (MI) was created by Congress in 1979, within the US Department of Energy, to afford the Secretary advice on the effect policies, regulations and other actions of DOE respecting minority participation in energy programs. The Director of MI is responsible for the conduct of ongoing research into the effects, including socio-economic and environmental, of national energy programs, policies, and regulations of the Department of minorities. Public housing in the United States is dominated by minorities, public housing is a large consumer of residential energy. Consequently, this project is a logical merging of these two factors and an attempt to somehow influence energy savings through improving public housing residents` energy-consumption practices. This final report attempts to capture the results of this current demonstration, and incorporate the historical basis for today`s results by renewing the efforts that preceded the implementation of energy conservation practices training in selected public housing developments.

Final report on implementation of energy conservation practices training in selected public housing developments

Energy Technology Data Exchange (ETDEWEB)

1991-10-01

This report on the implementation of energy conservation practices training in selected public housing developments represents an initiative of the Research and Education Division, Office of Minority Economic Impact, US Department of Energy. The Office of Minority Economic Impact (MI) was created by Congress in 1979, within the US Department of Energy, to afford the Secretary advice on the effect policies, regulations and other actions of DOE respecting minority participation in energy programs. The Director of MI is responsible for the conduct of ongoing research into the effects, including socio-economic and environmental, of national energy programs, policies, and regulations of the Department of minorities. Public housing in the United States is dominated by minorities, public housing is a large consumer of residential energy. Consequently, this project is a logical merging of these two factors and an attempt to somehow influence energy savings through improving public housing residents' energy-consumption practices. This final report attempts to capture the results of this current demonstration, and incorporate the historical basis for today's results by renewing the efforts that preceded the implementation of energy conservation practices training in selected public housing developments.

High-concentration sugars production from corn stover based on combined pretreatments and fed-batch process.

Science.gov (United States)

Yang, Maohua; Li, Wangliang; Liu, Binbin; Li, Qiang; Xing, Jianmin

2010-07-01

In this paper, high-concentration sugars were produced from pretreated corn stover. The raw corn stover was pretreated in a process combining steam explosion and alkaline hydrogen-peroxide. The hemicellulose and lignin were removed greatly. The cellulose content increased to 73.2%. Fed-batch enzymatic hydrolysis was initiated with 12% (w/v) solids loading and 20 FPU/g solids. Then, 6% solids were fed consecutively at 12, 36 and 60 h. After 144 h, the final concentrations of reducing sugar, glucose, cellobiose and xylose reached 220, 175, 22 and 20 g/L, respectively. The final total biomass conversion was 60% in fed-batch process. Copyright 2009 Elsevier Ltd. All rights reserved.

Effect of Tracking Error of Double-Axis Tracking Device on the Optical Performance of Solar Dish Concentrator

Directory of Open Access Journals (Sweden)

Jian Yan

2018-01-01

Full Text Available In this paper, a flux distribution model of the focal plane in dish concentrator system has been established based on ray tracking method. This model was adopted for researching the influence of the mirror slope error, solar direct normal irradiance, and tracking error of elevation-azimuth tracking device (EATD on the focal spot characteristics (i.e., flux distribution, geometrical shape, centroid position, and intercept factor. The tracking error transmission law of the EATD transferred to dish concentrator was also studied. The results show that the azimuth tracking error of the concentrator decreases with the increase of the concentrator elevation angle and it decreases to 0 mrad when the elevation angle is 90°. The centroid position of focal spot along x-axis and y-axis has linear relationship with azimuth and elevation tracking error of EATD, respectively, which could be used to evaluate and calibrate the tracking error of the dish concentrator. Finally, the transmission law of the EATD azimuth tracking error in solar heliostats is analyzed, and a dish concentrator using a spin-elevation tracking device is proposed, which can reduce the effect of spin tracking error on the dish concentrator. This work could provide fundamental for manufacturing precision allocation of tracking devices and developing a new type of tracking device.

Development of a vacuum crystallizer for the concentration of industrial waste water

NARCIS (Netherlands)

Roos, A.C.; Verschuur, R.-J.; Schreurs, B.; Scholz, R.; Jansens, P.J.

2002-01-01

Freeze concentration has proven to be a viable technology for the concentration of hazardous industrial waste waters before incineration. Owing to the relatively high investment cost of the technology, its applicability has been limited until now. This paper investigates the feasibility of a vacuum

Regulatory criteria for final disposal of radioactive wastes

International Nuclear Information System (INIS)

Petraitis, E.; Ciallella, N.; Siraky, G.

1998-01-01

This paper describes briefly the legislative and regulatory framework in which the final disposal of radioactive wastes is carried out in Argentina. It also presents the criteria developed by the Nuclear Regulatory Authority (ARN) to assess the long-term safety of final disposal systems for high level radioactive wastes. (author)

Urbanization and economic development: a bias toward large cities?

Science.gov (United States)

Moomaw, R L; Shatter, A M

1996-01-01

"We find that a nation's urban population percentage increases with GDP per capita; industrialization; export orientation; and possibly, foreign assistance. It decreases with the importance of agriculture. Industrialization and agricultural importance have the same implications for the concentration of urban population in cities with 100,000+ population as for the urban percentage. Greater export orientation reduces such concentration. Finally, GDP per capita, population, and export orientation reduce primacy. Political factors, such as whether a country's largest city is also its capital, affect primacy. Our results do not seem to imply that developing-country urbanization today differs fundamentally from urbanization in the past." excerpt

The conditions for uranium concentration in the phosphates of Tchivoula, Congo

International Nuclear Information System (INIS)

Giresse, P.; N'Landou, J. de Dieu; Wiber, M.

1986-01-01

The processes of deposition of marine phosphates in the Maastrichtian seas of the Congo do not appear capable alone of having produced the significant concentrations of uranium found. Diagenetic phenomena resulted in a mobilisation and a secondary concentration of uranium in the interior of recrystallized apatites. This secondary uranium may have been derived from the residual organic matrix in the deposit. Towards the top of the beds, hydrolysis of the apatites and authigenesis of crandallite, barrandite and ferruginous variscite led to uranium concentrations which are characteristic of alteration in a tropical climate. In contrast, wavellite, the final product of supergene alteration does not retain uranium. In the case of the Tchivoula deposits, the overlying Paleocene beds may have been the source of the uraniferous solutions' downslope movement which favored concentration in the underlying sediments. (orig.)

The active titration method for measuring local hydroxyl radical concentration

Science.gov (United States)

Sprengnether, Michele; Prinn, Ronald G.

1994-01-01

We are developing a method for measuring ambient OH by monitoring its rate of reaction with a chemical species. Our technique involves the local, instantaneous release of a mixture of saturated cyclic hydrocarbons (titrants) and perfluorocarbons (dispersants). These species must not normally be present in ambient air above the part per trillion concentration. We then track the mixture downwind using a real-time portable ECD tracer instrument. We collect air samples in canisters every few minutes for roughly one hour. We then return to the laboratory and analyze our air samples to determine the ratios of the titrant to dispersant concentrations. The trends in these ratios give us the ambient OH concentration from the relation: dlnR/dt = -k(OH). A successful measurement of OH requires that the trends in these ratios be measureable. We must not perturb ambient OH concentrations. The titrant to dispersant ratio must be spatially invariant. Finally, heterogeneous reactions of our titrant and dispersant species must be negligible relative to the titrant reaction with OH. We have conducted laboratory studies of our ability to measure the titrant to dispersant ratios as a function of concentration down to the few part per trillion concentration. We have subsequently used these results in a gaussian puff model to estimate our expected uncertainty in a field measurement of OH. Our results indicate that under a range of atmospheric conditions we expect to be able to measure OH with a sensitivity of 3x10(exp 5) cm(exp -3). In our most optimistic scenarios, we obtain a sensitivity of 1x10(exp 5) cm(exp -3). These sensitivity values reflect our anticipated ability to measure the ratio trends. However, because we are also using a rate constant to obtain our (OH) from this ratio trend, our accuracy cannot be better than that of the rate constant, which we expect to be about 20 percent.

Environmental Factors and Seasonality Affect the Concentration of Rotundone in Vitis vinifera L. cv. Shiraz Wine.

Directory of Open Access Journals (Sweden)

Pangzhen Zhang

Full Text Available Rotundone is a sesquiterpene that gives grapes and wine a desirable 'peppery' aroma. Previous research has reported that growing grapevines in a cool climate is an important factor that drives rotundone accumulation in grape berries and wine. This study used historical data sets to investigate which weather parameters are mostly influencing rotundone concentration in grape berries and wine. For this purpose, wines produced from 15 vintages from the same Shiraz vineyard (The Old Block, Mount Langi Ghiran, Victoria, Australia were analysed for rotundone concentration and compared to comprehensive weather data and minimal temperature information. Degree hours were obtained by interpolating available temperature information from the vineyard site using a simple piecewise cubic hermite interpolating polynomial method (PCHIP. Results showed that the highest concentrations of rotundone were consistently found in wines from cool and wet seasons. The Principal Component Analysis (PCA showed that the concentration of rotundone in wine was negatively correlated with daily solar exposure and grape bunch zone temperature, and positively correlated with vineyard water balance. Finally, models were constructed based on the Gompertz function to describe the dynamics of rotundone concentration in berries through the ripening process according to phenological and thermal times. This characterisation is an important step forward to potentially predict the final quality of the resultant wines based on the evolution of specific compounds in berries according to critical environmental and micrometeorological variables. The modelling techniques described in this paper were able to describe the behaviour of rotundone concentration based on seasonal weather conditions and grapevine phenological stages, and could be potentially used to predict the final rotundone concentration early in future growing seasons. This could enable the adoption of precision irrigation and

Environmental Factors and Seasonality Affect the Concentration of Rotundone in Vitis vinifera L. cv. Shiraz Wine

Science.gov (United States)

Zhang, Pangzhen; Howell, Kate; Krstic, Mark; Herderich, Markus; Barlow, Edward William R.; Fuentes, Sigfredo

2015-01-01

Rotundone is a sesquiterpene that gives grapes and wine a desirable ‘peppery’ aroma. Previous research has reported that growing grapevines in a cool climate is an important factor that drives rotundone accumulation in grape berries and wine. This study used historical data sets to investigate which weather parameters are mostly influencing rotundone concentration in grape berries and wine. For this purpose, wines produced from 15 vintages from the same Shiraz vineyard (The Old Block, Mount Langi Ghiran, Victoria, Australia) were analysed for rotundone concentration and compared to comprehensive weather data and minimal temperature information. Degree hours were obtained by interpolating available temperature information from the vineyard site using a simple piecewise cubic hermite interpolating polynomial method (PCHIP). Results showed that the highest concentrations of rotundone were consistently found in wines from cool and wet seasons. The Principal Component Analysis (PCA) showed that the concentration of rotundone in wine was negatively correlated with daily solar exposure and grape bunch zone temperature, and positively correlated with vineyard water balance. Finally, models were constructed based on the Gompertz function to describe the dynamics of rotundone concentration in berries through the ripening process according to phenological and thermal times. This characterisation is an important step forward to potentially predict the final quality of the resultant wines based on the evolution of specific compounds in berries according to critical environmental and micrometeorological variables. The modelling techniques described in this paper were able to describe the behaviour of rotundone concentration based on seasonal weather conditions and grapevine phenological stages, and could be potentially used to predict the final rotundone concentration early in future growing seasons. This could enable the adoption of precision irrigation and canopy

Geothermal Energy Development in the Eastern United States. Final Report

Energy Technology Data Exchange (ETDEWEB)

None

1981-10-01

This document represents the final report from the Applied Physics Laboratory (APL) of The Johns Hopkins University on its efforts on behalf of the Division of Geothermal Energy (DGE) of the Department of Energy (DOE). For the past four years, the Laboratory has been fostering development of geothermal energy in the Eastern United States. While the definition of ''Eastern'' has changed somewhat from time to time, basically it means the area of the continental United States east of the Rocky Mountains, plus Puerto Rico but excluding the geopressured regions of Texas and Louisiana. During these years, the Laboratory developed a background in geology, hydrology, and reservoir analysis to aid it in establishing the marketability of geothermal energy in the east. Contrary to the situation in the western states, the geothermal resource in the east was clearly understood to be inferior in accessible temperature. On the other hand, there were known to be copious quantities of water in various aquifers to carry the heat energy to the surface. More important still, the east possesses a relatively dense population and numerous commercial and industrial enterprises, so that thermal energy, almost wherever found, would have a market. Thus, very early on it was clear that the primary use for geothermal energy in the east would be for process heat and space conditioning--heating and cool electrical production was out of the question. The task then shifted to finding users colocated with resources. This task met with modest success on the Atlantic Coastal Plain. A great deal of economic and demographic analysis pinpointed the prospective beneficiaries, and an intensive ''outreach'' campaign was mounted to persuade the potential users to invest in geothermal energy. The major handicaps were: (1) The lack of demonstrated hydrothermal resources with known temperatures and expected longevity; and (2) The lack of a &apos

A survey of indoor radon and particular concentration

International Nuclear Information System (INIS)

Ohta, Yukiko

1993-01-01

Lung disease risk from inhalation of radon can be enhanced by the presence of particular pollutants in indoor air. The indoor concentration of radon and particulates were measured in homes, a department store, and offices in a high building in Tokyo metropolis, as well as in homes in both northern and western Japan. Passive radon monitors were located in living rooms and offices for more than three months at 99 sites during the winter of 1988 and 1989. Indoor radon concentration ranged from 11.1 Bq/m 3 to 148 Bq/m 3 (n=99) and averaged value S.D. was 36.5±14.2 Bq/m 3 . However, the average concentration in air conditional buildings was 21.8±9.51 Bq/m 3 (n=17). Simultaneously at 65 of the radon sites, indoor particulates were collected using personal dust samplers by impaction methods. Deposited particulate concentrations on the sampler were measured and calculated in a unit of μm/m 3 . Concentrations were determined for particle sizes above and below 2.5 μm, for both smoking or non smoking sites. Consequently, concentration of particle size below 2.5 μm was high in smoking rooms. Finally, it was considered that smoking was a complex indoor pollutant as adherence of radon daughter to aerosols. (author)

Development and evaluation of a regression-based model to predict cesium concentration ratios for freshwater fish

International Nuclear Information System (INIS)

Pinder, John E.; Rowan, David J.; Rasmussen, Joseph B.; Smith, Jim T.; Hinton, Thomas G.; Whicker, F.W.

2014-01-01

Data from published studies and World Wide Web sources were combined to produce and test a regression model to predict Cs concentration ratios for freshwater fish species. The accuracies of predicted concentration ratios, which were computed using 1) species trophic levels obtained from random resampling of known food items and 2) K concentrations in the water for 207 fish from 44 species and 43 locations, were tested against independent observations of ratios for 57 fish from 17 species from 25 locations. Accuracy was assessed as the percent of observed to predicted ratios within factors of 2 or 3. Conservatism, expressed as the lack of under prediction, was assessed as the percent of observed to predicted ratios that were less than 2 or less than 3. The model's median observed to predicted ratio was 1.26, which was not significantly different from 1, and 50% of the ratios were between 0.73 and 1.85. The percentages of ratios within factors of 2 or 3 were 67 and 82%, respectively. The percentages of ratios that were <2 or <3 were 79 and 88%, respectively. An example for Perca fluviatilis demonstrated that increased prediction accuracy could be obtained when more detailed knowledge of diet was available to estimate trophic level. - Highlights: • We developed a model to predict Cs concentration ratios for freshwater fish species. • The model uses only two variables to predict a species CR for any location. • One variable is the K concentration in the freshwater. • The other is a species mean trophic level measure easily obtained from (fishbase.org). • The median observed to predicted ratio for 57 independent test cases was 1.26

The Effect of Residential Concentration on Voter Turnout among Ethnic Minorities

DEFF Research Database (Denmark)

Bhatti, Yosef; Hansen, Kasper Møller

2016-01-01

Utilizing a large and unique dataset composed of government records, we study the widely contested effect of co-ethnic residential concentrations on voter turnout. Non-Western immigrants are moderately affected by the concentration of co-ethnic voters in their neighborhoods. As the local concentr......Utilizing a large and unique dataset composed of government records, we study the widely contested effect of co-ethnic residential concentrations on voter turnout. Non-Western immigrants are moderately affected by the concentration of co-ethnic voters in their neighborhoods. As the local...... concentration of same-ethnicity voters increases, so does the individual's propensity to turn out for the election. In general, the concentration of non-Western immigrants in the neighborhood has only a very limited impact on an immigrant's propensity to vote. Finally, we investigate the possible mobilizing...... effect of local candidates and, in particular, local co-ethnic candidates on voter turnout. We find that the presence of candidates in general and co-ethnic candidates running for office in a neighborhood has a moderate positive mobilization effect. However, taking this factor into account, the effect...

Implications of Industrial Processing Strategy on Cellulosic Ethanol Production at High Solids Concentrations

DEFF Research Database (Denmark)

Cannella, David

The production of cellulosic ethanol is a biochemical process of not edible biomasses which contain the cellulose. The process involves the use of enzymes to hydrolyze the cellulose in fermentable sugars to finally produce ethanol via fermentative microorganisms (i.e. yeasts). These biomasses...... are the leftover of agricultural productions (straws), not edible crops (giant reed) or wood, thus the ethanol so produced is also called second generation (or 2G ethanol), which differs from the first generation produced from starch (sugar beets mostly). In the industrial production of cellulosic ethanol high...... solids strategy resulted critical for its cost effectiveness: high concentration of initial biomass it will lead to high concentration of the final product (ethanol), thus more convenient to isolate. This thesis investigate the implementation of a high solids loading concept into cellulosic ethanol...

Project development for mining-metallurgical complexes for production of uranium concentrates - an analysis and a methodology

International Nuclear Information System (INIS)

Ajuria G, S.; Blanco P, B.; Pena A, J.; Manzanera Q, C.

1978-10-01

Activities comprising the development of a project for a mining-metallurgical complex for production of uranium concentrates, from sampling and evaluation of an orebody until plant start-up, are analyzed. The analysis of the orebody, characterization of the ore, bench scale and pilot plant metallurgical studies, environmental studies and economic analyses of the project are described. The mining project and mine preparation and engineering and construction of the plant are reviewed in less detail. The estimated time lapse for the development of a typical project under ideal conditions is 66 months. A bar diagram is included showing an approximate timetable for each activity. (author)

Atmospheric relative concentrations in building wakes

International Nuclear Information System (INIS)

Ramsdell, J.V. Jr.; Simonen, C.A.

1997-05-01

This report documents the ARCON96 computer code developed for the U.S. Nuclear Regulatory Commission Office of Nuclear Reactor Regulation for potential use in control room habitability assessments. It includes a user's guide to the code, a description of the technical basis for the code, and a programmer's guide to the code. The ARCON96 code uses hourly meteorological data and recently developed methods for estimating dispersion in the vicinity of buildings to calculate relative concentrations at control room air intakes that would be exceeded no more than five percent of the time. The concentrations are calculated for averaging periods ranging from one hour to 30 days in duration. ARCON96 is a revised version of ARCON95, which was developed for the NRC Office of Nuclear Regulatory Research. Changes in the code permit users to simulate releases from area sources as well as point sources. The method of averaging concentrations for periods longer than 2 hours has also been changed. The change in averaging procedures increases relative concentrations for these averaging periods. In general, the increase in concentrations is less than a factor of two. The increase is greatest for relatively short averaging periods, for example 0 to 8 hours and diminishes as the duration of the averaging period increases

Loggerhead sea turtle (Caretta caretta) egg yolk concentrations of persistent organic pollutants and lipid increase during the last stage of embryonic development

Energy Technology Data Exchange (ETDEWEB)

Alava, Juan Jose [School of the Environment, University of South Carolina, 702G Byrnes Building, Columbia, SC 29208 (United States) and Center for Coastal Environmental Health and Biomolecular Research, National Oceanic and Atmospheric Administration, 219 Ft. Johnson Road, Charleston, SC 29412 (United States)]. E-mail: jalavasa@sfu.ca; Keller, Jennifer M. [National Institute of Standards and Technology, Hollings Marine Laboratory, 331 Fort Johnson Road, Charleston, SC 29412 (United States)]. E-mail: Jennifer.Keller@noaa.gov; Kucklick, John R. [National Institute of Standards and Technology, Hollings Marine Laboratory, 331 Fort Johnson Road, Charleston, SC 29412 (United States); Wyneken, Jeanette [Florida Atlantic University, Department of Biological Sciences, 777 Glades Road, Boca Raton, FL 33431 (United States); Crowder, Larry [Duke University Marine Laboratory, 135 Duke Marine Lab Road, Beaufort, NC 28516 (United States); Scott, Geoffrey I. [Center for Coastal Environmental Health and Biomolecular Research, National Oceanic and Atmospheric Administration, 219 Ft. Johnson Road, Charleston, SC 29412 (United States)

2006-08-15

Data are scarce describing the concentrations of polychlorinated biphenyls (PCBs) and organochlorine pesticides in sea turtle eggs. The purpose of this study was to establish appropriate sample collection methodology to monitor these contaminants in sea turtle eggs. Contaminant concentrations were measured in yolk samples from eggs that failed to hatch from three loggerhead sea turtle (Caretta caretta) nests collected in southern Florida to determine if concentrations change through embryonic development. One to three egg yolk samples per nest were analyzed from early, middle, and late developmental stages (n = 22 eggs total). PCB and pesticide concentrations were determined by gas chromatography with electron capture detection (GC-ECD). Geometric mean concentrations of {sigma}PCBs (52 congeners), {sigma}DDTs, {sigma}chlordanes, and dieldrin in all eggs were 65.0 (range = 7.11 to 3930 ng/g lipid), 67.1 (range = 7.88 to 1340 ng/g lipid), 37.0 (range = 4.04 to 685 ng/g lipid), and 11.1 ng/g lipid (range = 1.69 to 44.0 ng/g lipid), respectively. Early and middle developmental stage samples had similar concentrations of PCBs and organochlorine pesticides on a wet-mass basis (ng/g tissue extracted), but the concentrations doubled by the late stage. This increase is most likely attributable to the 50% increase in lipid content observed in the late-stage yolk. These findings indicate that an early-stage sample cannot be directly compared to a late-stage sample, especially from different nests. These preliminary findings also allowed us to calculate the minimum number of eggs per nest required for analysis to obtain an acceptable mean concentration per nest. More research is required to investigate geographical trends of contaminant concentrations and potential health effects (i.e., abnormalities) caused by these contaminants on sea turtle development.

Loggerhead sea turtle (Caretta caretta) egg yolk concentrations of persistent organic pollutants and lipid increase during the last stage of embryonic development

International Nuclear Information System (INIS)

Alava, Juan Jose; Keller, Jennifer M.; Kucklick, John R.; Wyneken, Jeanette; Crowder, Larry; Scott, Geoffrey I.

2006-01-01

Data are scarce describing the concentrations of polychlorinated biphenyls (PCBs) and organochlorine pesticides in sea turtle eggs. The purpose of this study was to establish appropriate sample collection methodology to monitor these contaminants in sea turtle eggs. Contaminant concentrations were measured in yolk samples from eggs that failed to hatch from three loggerhead sea turtle (Caretta caretta) nests collected in southern Florida to determine if concentrations change through embryonic development. One to three egg yolk samples per nest were analyzed from early, middle, and late developmental stages (n = 22 eggs total). PCB and pesticide concentrations were determined by gas chromatography with electron capture detection (GC-ECD). Geometric mean concentrations of ΣPCBs (52 congeners), ΣDDTs, Σchlordanes, and dieldrin in all eggs were 65.0 (range = 7.11 to 3930 ng/g lipid), 67.1 (range = 7.88 to 1340 ng/g lipid), 37.0 (range = 4.04 to 685 ng/g lipid), and 11.1 ng/g lipid (range = 1.69 to 44.0 ng/g lipid), respectively. Early and middle developmental stage samples had similar concentrations of PCBs and organochlorine pesticides on a wet-mass basis (ng/g tissue extracted), but the concentrations doubled by the late stage. This increase is most likely attributable to the 50% increase in lipid content observed in the late-stage yolk. These findings indicate that an early-stage sample cannot be directly compared to a late-stage sample, especially from different nests. These preliminary findings also allowed us to calculate the minimum number of eggs per nest required for analysis to obtain an acceptable mean concentration per nest. More research is required to investigate geographical trends of contaminant concentrations and potential health effects (i.e., abnormalities) caused by these contaminants on sea turtle development

Development of a system of programs HAMMER - ORIGEN - 2 system

International Nuclear Information System (INIS)

Guimaraes, L.N.F.

1984-07-01

The development of a system of programs (Hamor-2) to calculate precision inventory of LWR reactors is presented. The Hamor-2 code generates with the Hammer-technion code the four (4) energy groupe effective cross section of the actinides: U-235, U-236, U-238, Pu-239, Pu-240, Pu-241, Pu-242. Hamor-2 collapses the four group energy effective cross section to one group energy effective cross section. Hamor-2 calculates with origen-2 the new concentrations for the actinides using the one group energy effective cross section. Two PWR reactors were analised. (HBR, KWO). The discrepancy between the final actinides conentration results calculated by Hamor-2 and the results of measures finded in the references were calculated. That discrepancies have been compared with the discrepancy between : the final actinide concentration results calculated by Origen-2 and some measured results finded in the references. (E.G.) [pt

Measurement of attitudes toward commercial development of geothermal energy in Federal Region IX. Final report

Energy Technology Data Exchange (ETDEWEB)

1981-06-01

A survey was conducted of ten target study groups and subgroups for Klamath Falls, Oregon, and Susanville, California: local government, current and potential industry at the site, relocators to the site, current and potential financial community, regulators, and current and potential promoters and developers. The results of benchmark attitudinal measurement is presented separately for each target group. A literature review was conducted and Macro-environmental attitudes of a sample of local government and industry personnel at the sites were assessed. An assessment of capabilities was made which involved two measurements. The first was a measurement of a sample of promoters, developers, and industrial service companies active at the site to determine infrastructure capabilities required by industry for geothermal plants. The second measurement involved analyzing a sample of industry management in the area and defining their requirements for plant retrofit and expansion. Finally, the processes used by the study group to analyze information to reach commitment and regulatory decisions that significantly impact on geothermal energy projects at the site were identified and defined.

Energetical optimization and parameters selection for a fixed faceted mirror concentrator

International Nuclear Information System (INIS)

Nicolas, R.O.; Duran, J.C.; Dawidowski, L.E.

1990-01-01

A method which allows to select the parameters of a cylindrical solar collector by means of an energetical optimization is presented. In particular, the energy collected by the operating fluid and the collection efficiency of a Fixed Faceted Mirror Concentrator (FFMC) are obtained and compared for different sets of parameters. To this end, the two-dimensional optical analysis for non-perfect cylindrical concentrators presented previously is used. Some graphs analyzing the variations of the yearly efficiency of the FFMC as a function of those parameters are given. Finally, the possibility of using a second concentrator in the receiver plane of the FFMC in order to improve the whole efficiency of the prototype is also analyzed. (Author)

SiC Schottky Diode Detectors for Measurement of Actinide Concentrations from Alpha Activities in Molten Salt Electrolyte

International Nuclear Information System (INIS)

Windl, Wolfgang; Blue, Thomas

2013-01-01

In this project, we have designed a 4H-SiC Schottky diode detector device in order to monitor actinide concentrations in extreme environments, such as present in pyroprocessing of spent fuel. For the first time, we have demonstrated high temperature operation of such a device up to 500 °C in successfully detecting alpha particles. We have used Am-241 as an alpha source for our laboratory experiments. Along with the experiments, we have developed a multiscale model to study the phenomena controlling the device behavior and to be able to predict the device performance. Our multiscale model consists of ab initio modeling to understand defect energetics and their effect on electronic structure and carrier mobility in the material. Further, we have developed the basis for a damage evolution model incorporating the outputs from ab initio model in order to predict respective defect concentrations in the device material. Finally, a fully equipped TCAD-based device model has been developed to study the phenomena controlling the device behavior. Using this model, we have proven our concept that the detector is capable of performing alpha detection in a salt bath with the mixtures of actinides present in a pyroprocessing environment.

SiC Schottky Diode Detectors for Measurement of Actinide Concentrations from Alpha Activities in Molten Salt Electrolyte

Energy Technology Data Exchange (ETDEWEB)

Windl, Wolfgang [The Ohio State Univ., Columbus, OH (United States); Blue, Thomas [The Ohio State Univ., Columbus, OH (United States)

2013-01-28

In this project, we have designed a 4H-SiC Schottky diode detector device in order to monitor actinide concentrations in extreme environments, such as present in pyroprocessing of spent fuel. For the first time, we have demonstrated high temperature operation of such a device up to 500 °C in successfully detecting alpha particles. We have used Am-241 as an alpha source for our laboratory experiments. Along with the experiments, we have developed a multiscale model to study the phenomena controlling the device behavior and to be able to predict the device performance. Our multiscale model consists of ab initio modeling to understand defect energetics and their effect on electronic structure and carrier mobility in the material. Further, we have developed the basis for a damage evolution model incorporating the outputs from ab initio model in order to predict respective defect concentrations in the device material. Finally, a fully equipped TCAD-based device model has been developed to study the phenomena controlling the device behavior. Using this model, we have proven our concept that the detector is capable of performing alpha detection in a salt bath with the mixtures of actinides present in a pyroprocessing environment.

Immigrant and Native Children's Cognitive Outcomes and the Effect of Ethnic Concentration in Danish Schools

DEFF Research Database (Denmark)

Jensen, Peter; Wurtz Rasmussen, Astrid

are still important factors in determining the child.s cognitive outcome. However, the negative effect of ethnic concentration in the school is only significant for the native Danish children. Finally, there is a strong positive effect on the children.s cognitive outcome of speaking Danish at home....... to the ethnic concentration in the schools they attend and their relatively low socioeconomic status. Instrumenting for ethnic concentration reveals that even after taking into consideration that individuals may sort across neighborhoods, ethnic concentration in the school and the child's own ethnicity...

Market concentration, corporate governance and innovation: Partial and combined effects in US-listed firms

Directory of Open Access Journals (Sweden)

Mehmet Ugur

2012-10-01

Full Text Available Existing research on the relationship between market concentration and innovation has produced conflicting findings. In addition, the emerging literature on the relationship between corporate governance and innovation tends to focus only on partial effects of corporate governance on innovation. We aim to contribute to the debate by investigating both partial and combined effects of corporate governance and market concentration on innovation. Utilising a dataset for 1,400 non-financial US-listed companies and two-way cluster-robust estimation methodology, we report several findings. First, the relationship between market concentration and innovation is non-linear. Secondly, the relationship has a U-shape in the case of input measure of innovation (research and development - R&D – expenditures; but it has an inverted-U shape when net book-value of brands and patents is used as output measure of innovation. Third, corporate governance indicators such as anti-takeover defences and insider control tend to have a negative partial effect on R&D expenditures but a positive partial effect on net book-value of brands and patents. Finally, when interacted with market concentration, anti-takeover defences and insider control act as complements to market concentration. Hence, firms with strong anti-take-over defences and under insider control tend to spend more on R&D but are less able to generate valuable brands and patents as market concentration increases. These results are based on two-way cluster-robust estimation, which takes account of both serial and cross-sectional dependence in the error terms.

Assessment of chimeric mice with humanized livers in new drug development: generation of pharmacokinetics, metabolism and toxicity data for selecting the final candidate compound.

Science.gov (United States)

Kamimura, Hidetaka; Ito, Satoshi

2016-01-01

1. Chimeric mice with humanized livers are expected to be a novel tool for new drug development. This review discusses four applications where these animals can be used efficiently to collect supportive data for selecting the best compound in the final stage of drug discovery. 2. The first application is selection of the final compound based on estimated pharmacokinetic parameters in humans. Since chimeric mouse livers are highly repopulated with human hepatocytes, hepatic clearance values in vivo could be used preferentially to estimate pharmacokinetic profiles for humans. 3. The second is prediction of human-specific or disproportionate metabolites. Chimeric mice reproduce human-specific metabolites of drugs under development to conform to ICH guidance M3(R2), except for compounds that were extensively eliminated by co-existing mouse hepatocytes. 4. The third is identifying metabolites with distinct pharmacokinetic profiles in humans. Slow metabolite elimination specifically in humans increases its exposure level, but if its elimination is faster in laboratory animals, the animal exposure level might not satisfy ICH guidance M3(R2). 5. Finally, two examples of reproducing acute liver toxicity in chimeric mice are introduced. Integrated pharmacokinetics, metabolism and toxicity information are expected to assist pharmaceutical scientists in selecting the best candidate compound in new drug development.

Electroproduction of associated two-body final states

International Nuclear Information System (INIS)

Harding, D.J.

1983-01-01

The Large Aperture Magnet Experiment at the Cornell Electron Synchrotron measured electron scattering in the region 2.98 2 and 0.5 2 2 . The 11.5 GeV extracted electron beam struck a liquid hydrogen target in an eight kilogauss magnetic field. The charged particles in the final state were tracked through the field by a multiwire proportional chamber system of 34 planes. A lead-scintillator shower counter triggered the experiment on detection of a scattered electron. Time-of-flight and water Cherenkov counters identified some of the final state hadrons. The data recorded on tape was then passed through computer programs which linked proportional chamber strikes into tracks, fit momenta to the tracks, applied particle identification algorithms, selected interesting events, and plotted histograms of invariant masses. All of this is described here in detail, with special attention to the front-end electronics and the track-finding program. Many specific final states were observed. The analysis presented here concentrates on the reaction γ/sub v/p→pπ + ππ 0 , with the final hadrons resulting from the decay of a two-body state. The states pω 0 and p eta 0 are measured. Limits are set for the production of Δ + + rho - , Δ + rho 0 , and Δp + . The conclusion the author draws is that hadron-like two-body processes are almost completely absent in virtual photon scattering in this kinematic region. Vector meson production, excitation of the nucleons, and the scattering of the photons directly from individual partons are the important processes

Performance investigation of low – Concentration photovoltaic systems under hot and arid conditions: Experimental and numerical results

International Nuclear Information System (INIS)

Yousef, Mohamed S.; Abdel Rahman, Ali K.; Ookawara, S.

2016-01-01

Highlights: • Influence of cooling on the performance of photovoltaic systems. • A comprehensive model (optical, thermal, and electrical) was developed. • Experimental measurements were conducted under hot climate conditions. • For conventional photovoltaic with cooling, about 11% more power was obtained. • For concentrated photovoltaic with cooling, about 15% more power was obtained. - Abstract: In this study, a comparative performance analysis was performed between a conventional photovoltaic system and a low-concentration photovoltaic system. Two typical photovoltaic modules and two compound parabolic concentrating photovoltaic systems were examined. A Cooling system was employed to lower the temperature of the solar cells in each of the two configurations. Experimental and numerical investigations of the performance of the two arrangements with and without cooling were presented. Experiments were conducted outdoors at the Egypt-Japan University of Science and Technology, subjected to the hot climate conditions of New Borg El-Arab City, Alexandria, Egypt (Longitude/Latitude: E 029°42′/N 30°55′). A comprehensive system model was established, which comprises an optical model, coupled with thermal and electrical models. The coupled model was developed analytically and solved numerically, using MATLAB software, to assess the overall performance of the two configurations, considering the concentration ratio of the concentrated photovoltaic system to be 2.4X. The results indicated that cooling the solar panels considerably improved the electrical power yield of the photovoltaic systems. By employing cooling, the temperatures of the conventional photovoltaic system and the concentrated photovoltaic system were effectively lowered by approximately 25% and 30%, respectively, resulting in a significant enhancement in the electrical power output of the photovoltaic system by 11% and that of the concentrated photovoltaic system by 15%. Furthermore, the

State of the art and review on the treatment technologies of water reverse osmosis concentrates.

Science.gov (United States)

Pérez-González, A; Urtiaga, A M; Ibáñez, R; Ortiz, I

2012-02-01

The growing demand for fresh water is partially satisfied by desalination plants that increasingly use membrane technologies and among them reverse osmosis to produce purified water. Operating with water recoveries from 35% to 85% RO plants generate huge volumes of concentrates containing all the retained compounds that are commonly discharged to water bodies and constitute a potentially serious threat to marine ecosystems; therefore there is an urgent need for environmentally friendly management options of RO brines. This paper gives an overview on the potential treatments to overcome the environmental problems associated to the direct discharge of RO concentrates. The treatment options have been classified according to the source of RO concentrates and the maturity of the technologies. For the sake of clarity three different sources of RO concentrates are differentiated i) desalination plants, ii) tertiary processes in WWTP, and iii) mining industries. Starting with traditional treatments such as evaporation and crystallization other technologies that have emerged in last years to reduce the volume of the concentrate before disposal and with the objective of achieving zero liquid discharge and recovery of valuable compounds from these effluents are also reviewed. Most of these emerging technologies have been developed at laboratory or pilot plant scale (see Table 1). With regard to RO concentrates from WWTP, the manuscript addresses recent studies that are mainly focused on reducing the organic pollutant load through the application of innovative advanced oxidation technologies. Finally, works that report the treatment of RO concentrates from industrial sources are analyzed as well. Copyright © 2011 Elsevier Ltd. All rights reserved.

Understanding particulate coating microstructure development

Science.gov (United States)

Roberts, Christine Cardinal

How a dispersion of particulates suspended in a solvent dries into a solid coating often is more important to the final coating quality than even its composition. Essential properties like porosity, strength, gloss, particulate order, and concentration gradients are all determined by the way the particles come together as the coating dries. Cryogenic scanning electron microscopy (cryoSEM) is one of the most effective methods to directly visualize a drying coating during film formation. Using this method, the coating is frozen, arresting particulate motion and solidifying the sample so that it be imaged in an SEM. In this thesis, the microstructure development of particulate coatings was explored with several case studies. First, the effect of drying conditions was determined on the collapse of hollow latex particles, which are inexpensive whiteners for paint. Using cryoSEM, it was found that collapse occurs during the last stages of drying and is most likely to occur at high drying temperatures, humidity, and with low binder concentration. From these results, a theoretical model was proposed for the collapse of a hollow latex particle. CryoSEM was also used to verify a theoretical model for the particulate concentration gradients that may develop in a coating during drying for various evaporation, sedimentation and particulate diffusion rates. This work created a simple drying map that will allow others to predict the character of a drying coating based on easily calculable parameters. Finally, the effect of temperature on the coalescence and cracking of latex coatings was explored. A new drying regime for latex coatings was identified, where partial coalescence of particles does not prevent cracking. Silica was shown to be an environmentally friendly additive for preventing crack formation in this regime.

Trans-Pecos Photovoltaic Concentration Experiment. Final report for Phase-I system design, 6 June 1978-28 February 1979

Energy Technology Data Exchange (ETDEWEB)

Marcy, W.M.; Dudek, R.A.

1979-03-30

The Trans-Pecos Photovoltaic Concentrating Experiment is the design of a 200 kWe peak photovoltaic concentrating system applied to deep well irrigation in the Trans-Pecos region of Texas. The site selected is typical of deep well irrigation in arid regions of Texas, New Mexico, and Arizona. The existing well utilizes a 200 horse power, three phase, 480 volt induction motor to lift water 540 feet to irrigate 380 acres. The Trans-Pecos Photovoltaic Concentration (PVC) system employs a two axis (azimuth-elevation) tracking parabolic concentrator module that focuses sunlight at 38X concentration on two strings of actively cooled silicon solar cells. The direct current from a field of 102 collector modules is converted by a maximum power point electric power conditioning system to three phase alternating current. The power from the power conditioning system is connected through appropriate switchgear in parallel with the utility grid to the well's induction motor. The operational philosophy of the experiment is to displace daytime utility power with solar generated electric power. The solar system is sized to provide approximately 50 percent of the 24 hour energy demand of the motor. This requires an energy exchange with the utility since peak solar power (200 kWe) generated exceeds the peak motor demand (149.2 kWe). The annual energy production is projected to be 511 Mwh using El Paso, Texas solar TMY data. System electrical power production efficiency is projected to be 7.4 percent at the design point, and 7.0 percent on an annual electrical energy production basis. The system is projected to provide 37.8 percent of the 24 hour energy demand of the motor at the design point of March 10, excluding energy delivered to the grid in excess of motor demand. The total energy produced is projected to be 39.0 percent of the 24 hour energy demand of the motor at the design point of March 10.

Ethical aspects of final disposal. Final report

International Nuclear Information System (INIS)

Baltes, B.; Leder, W.; Achenbach, G.B.; Spaemann, R.; Gerhardt, V.

2003-01-01

In fulfilment of this task the Federal Environmental Ministry has commissioned GRS to summarise the current national and international status of ethical aspects of the final disposal of radioactive wastes as part of the project titled ''Final disposal of radioactive wastes as seen from the viewpoint of ethical objectives''. The questions arising from the opinions, positions and publications presented in the report by GRS were to serve as a basis for an expert discussion or an interdisciplinary discussion forum for all concerned with the ethical aspects of an answerable approach to the final disposal of radioactive wastes. In April 2001 GRS held a one-day seminar at which leading ethicists and philosophers offered statements on the questions referred to above and joined in a discussion with experts on issues of final disposal. This report documents the questions that arose ahead of the workshop, the specialist lectures held there and a summary of the discussion results [de

Solidification of radioactive liquid wastes. A comparison of treatment options for spent resins and concentrates

International Nuclear Information System (INIS)

Roth, A.; Willmann, F.; Ebata, M.; Wendt, S.

2008-01-01

Ion exchange is one of the most common and effective treatment methods for liquid radioactive waste. However, spent ion exchange resins are considered to be problematic waste that in many cases require special approaches and pre-conditioning during its immobilization to meet the acceptance criteria for disposal. Because of the function that they fulfill, spent ion exchange resins often contain high concentrations of radioactivity and pose special handling and treatment problems. Another very common method of liquid radioactive waste treatment and water cleaning is the evaporation or diaphragm filtration. Both treatment options offer a high volume reduction of the total volume of liquids treated but generate concentrates which contain high concentrations of radioactivity. Both mentioned waste streams, spent resins as well as concentrates, resulting from first step liquid radioactive waste treatment systems have to be conditioned in a suitable manner to achieve stable waste products for final disposal. The most common method of treatment of such waste streams is the solidification in a solid matrix with additional inactive material like cement, polymer etc. In the past good results have been achieved and the high concentration of radioactivity can be reduced by adding the inactive material. On the other hand, under the environment of limited space for interim storage and the absence of a final repository site, the built-up of additional volume has to be considered as very critical. Moreover, corrosive effects on cemented drums during long-term interim storage at the surface have raised doubts about the long-term stability of such waste products. In order to avoid such disadvantages solidification methods have been improved in order to get a well-defined product with a better load factor of wastes in the matrix. In a complete different approach, other technologies solidify the liquid radioactive wastes without adding of any inactive material by means of drying

Determination of hexavalent chromium concentration in industrial waste incinerator stack gas by using a modified ion chromatography with post-column derivatization method.

Science.gov (United States)

Miyake, Yuichi; Tokumura, Masahiro; Iwazaki, Yuta; Wang, Qi; Amagai, Takashi; Horii, Yuichi; Otsuka, Hideyuki; Tanikawa, Noboru; Kobayashi, Takeshi; Oguchi, Masahiro

2017-06-16

An ion chromatography with post-column derivatization with 1,5-diphenylcarbazide (IC-DPC) analytical method was modified to enable measurement of trace-level hexavalent chromium (Cr(VI)) in air. One of the difficulties in determining trace levels of Cr(VI) in air with conventional IC-DPC methods is co-elution of the solvent and ion peaks due to high concentrations of ionic compounds in the extract. However, by using gradient elution rather than isocratic elution we were able to fully resolve the Cr(VI) ion peak from the solvent peak without the need for diluting the extract, which would have reduced the minimum quantifiable level of the method. With this method, we were able to detect Cr(VI) in air at concentrations of 5.3ng/m 3 (assuming a sampling volume of 1m 3 and a final solution volume of 10mL). Recovery tests at three different concentrations of Cr(VI) (50, 250, 1000ng) were performed with or without fly ash; recovery rates at all the concentrations of Cr(VI), with or without fly ash, ranged from 68% to 110% (mean±relative standard deviation, 96%±11%), and there were no differences in recovery rates with respect to the presence or absence of fly ash. Finally, we used the developed method to determine the concentration of Cr(VI) in stack gases collected from eight industrial waste incinerators located in Japan. The concentration of Cr(VI) in the stack gases ranged from below the method quantification limit to 3100ng/m 3 . The highest concentrations of Cr(VI) detected in the stack gases were two to three orders of magnitude higher than that in ambient air in Japan. Copyright © 2017 Elsevier B.V. All rights reserved.

Solidification of radioactive liquid wastes, Treatment options for spent resins and concentrates - 16405

International Nuclear Information System (INIS)

Roth, Andreas

2009-01-01

Ion exchange is one of the most common and effective treatment methods for liquid radioactive waste. However, spent ion exchange resins are considered to be problematic waste that in many cases require special approaches and pre-conditioning during its immobilization to meet the acceptance criteria for disposal. Because of the function that they fulfill, spent ion exchange resins often contain high concentrations of radioactivity and pose special handling and treatment problems. Another very common method of liquid radioactive waste treatment and water cleaning is the evaporation or diaphragm filtration. Both treatment options offer a high volume reduction of the total volume of liquids treated but generate concentrates which contain high concentrations of radioactivity. Both mentioned waste streams, spent resins as well as concentrates, resulting from first step liquid radioactive waste treatment systems have to be conditioned in a suitable manner to achieve stable waste products for final disposal. Spent resin and concentrate treatment often appear as a specific task in decommissioning projects, because in the past those waste streams typically had been stored in tanks for the lifetime of the plant and needs to be retrieved, conditioned and packed prior to dismantling activities. Additionally a large amount of contaminated liquids will be generated by utilizing decontamination processes and needs to be processed further on. Such treatment options need to achieve waste products acceptable for final disposal, because due to the closure of the site no interim storage can be envisaged. The most common method of treatment of such waste streams is the solidification in a solid matrix with additional inactive material like cement, polymer etc. In the past good results have been achieved and the high concentration of radioactivity can be reduced by adding the inactive material. On the other hand, under the environment of limited space for interim storage and the absence

Ownership concentration and bank profitability

Directory of Open Access Journals (Sweden)

Peterson Kitakogelu Ozili

2017-12-01

Full Text Available We investigate whether ownership concentration influences bank profitability in a developing country context. We focus on bank ownership concentration measured as the amount of direct equity held by a majority shareholder categorised into: high ownership concentration, moderate ownership concentration and disperse ownership. We find that banks with high ownership concentration have higher return on assets, higher net interest margin and higher recurring earning power while banks with dispersed ownership have lower return on assets but have higher return on equity. Also, higher cost efficiency improves the return on assets of widely-held banks and the return on equity of banks with moderate ownership. The findings have implications. JEL: Code: G3, G34, G31, Keywords: Corporate governance, Ownership structure, Agency theory, Profitability, Firm performance, Banks, Return on asset, Return on equity

Heavy mineral concentration from oil sand tailings

Energy Technology Data Exchange (ETDEWEB)

Chachula, F.; Erasmus, N. [Titanium Corp. Inc., Regina, SK (Canada)

2008-07-01

This presentation described a unique technique to recover heavy minerals contained in the froth treatment tailings produced by oil sand mining extraction operations in Fort McMurray, Alberta. In an effort to process waste material into valuable products, Titanium Corporation is developing technology to recover heavy minerals, primarily zircon, and a portion of bitumen contained in the final stage of bitumen processing. The process technology is being developed to apply to all mined oil sands operations in the Fort McMurray region. In 2004, Titanium Corporation commissioned a pilot research facility at the Saskatchewan Research Council to test dry oil sands tailings. In 2005, a bulk sampling pilot plant was connected to the fresh oil sands tailings pipeline on-site in Fort McMurray, where washed sands containing heavy minerals were processed at a pilot facility. The mineral content in both deposited tailings and fresh pipeline tailings was assessed. Analysis of fresh tailings on a daily basis identified a constant proportion of zircon and higher levels of associated bitumen compared with the material in the deposited tailings. The process flow sheet design was then modified to remove bitumen from the heavy minerals and concentrate the minerals. A newly modified flotation process was shown to be a viable processing route to recover the heavy minerals from froth treatment tailings. 8 refs., 9 tabs., 12 figs.

Development of Interior Permanent Magnet Motors with Concentrated Windings for Reducing Magnet Eddy Current Loss

Science.gov (United States)

Yamazaki, Katsumi; Kanou, Yuji; Fukushima, Yu; Ohki, Shunji; Nezu, Akira; Ikemi, Takeshi; Mizokami, Ryoichi

In this paper, we present the development of interior magnet motors with concentrated windings, which reduce the eddy current loss of the magnets. First, the mechanism of the magnet eddy current loss generation is investigated by a simple linear magnetic circuit. Due to the consideration, an automatic optimization method using an adaptive finite element method is carried out to determine the stator and rotor shapes, which decrease the eddy current loss of the magnet. The determined stator and rotor are manufactured in order to proof the effectiveness by the measurement.

Investigation of the areas of high radon concentration in Gyeongju

International Nuclear Information System (INIS)

Lee, Jung Min; Park, Chan Hee; Kim, Shin Jae; Moon, Joo Hyun

2013-01-01

The aim of this study was to survey the radon concentrations at 21 elementary schools in Gyeongju, Republic of Korea, to identify those schools with high radon concentrations. Considering their geological characteristics and the preliminary survey results, three schools were finally placed under close scrutiny. For these three schools, continuous measurements over 48 h were taken at the principal's and administration office. The radon concentrations at one school, Naenam, exceeded the action level (148 Bq/m 3 ) established by the U.S. EPA, while those at the other two schools were below that level. - Highlights: • Preliminary measurements of the indoor radon concentrations were performed at the auditoriums in 23 elementary schools in Gyeongju. • Considering the geological characteristics and preliminary survey results, three elementary schools were screened for closer scrutiny. • For the three schools, continuous measurements were made at their principal's and administration offices over 48-h period. • The scrutiny revealed one elementary school of high radon concentration much higher than the U.S. EPA action level

Moonshot Panel Moving Toward Final Report

Science.gov (United States)

An NCI Cancer Currents blog from acting NCI Director Dr. Doug Lowy providing an update on the activities of the National Cancer Moonshot Initiative’s Blue Ribbon Panel and its work to develop a final report.

Air concentration and ground deposition following radioactive airborne releases

International Nuclear Information System (INIS)

Brofferio, C.; Cagnetti, P.; Ferrara, V.

1985-01-01

The fundamental aim of this report is to provide the mathematical and physical operational basis for the evaluation of air concentration and ground deposition, following radioactive airborne releases from a nuclear power plant, both during normal operations and in accidental conditions. As far as accidental releases are concerned, the basical assumptions on meteorological and diffusive situation are considered from a safety point of view: namely those pessimistic but realistically representative situation are taken into account which lead to maximum air concentration and ground deposition values, even if characterized by low recurrence probability. Those elements are the inputs for many environmental transfer models of maximum consequence evaluations up to man. As far as routine releases are concerned, it is shown, together with the usual models based on long term averaged meteorological conditions, also models studied to estimate atmospheric diffusion and deposition in low wind situations and in fog conditions, being those latter very frequent in the Po valley. Finally, the main operations and modalities of collecting and elaborating meteorological data for for radioprotection evaluations are also shown. It is to be pointed out that the methods and the models developed and considered in this work are of a more general validity, and can be also used for applications concerning non-radioactive releases, as it is the case when dealing with conventional power plants

First trimester serum afamin concentrations are associated with the development of pre-eclampsia and gestational diabetes mellitus in pregnant women.

Science.gov (United States)

Tramontana, Allessandra; Dieplinger, Benjamin; Stangl, Gerhard; Hafner, Erich; Dieplinger, Hans

2018-01-01

Aim of this study was to assess the prognostic capability of afamin to predict pregnancy complications. First-trimester screening was consecutively performed in 4948 pregnant women, of whom 474 women developed pregnancy complications [gestational hypertension (n=84), pre-eclampsia (n=30), intrauterine growth restriction (n=107), preterm birth (n=44), and gestational diabetes mellitus (n=209)]. To each woman with pregnancy complications an uncomplicated pregnancy was matched for body mass index. Afamin serum concentrations were measured in 948 pregnant women at the first-trimester screening. Median afamin concentrations were significantly higher in women developing pre-eclampsia or gestational diabetes mellitus when compared to women with uncomplicated pregnancies (76mg/L vs. 65mg/L, p=0.001 and 80mg/L vs. 69mg/L, p65mg/L) was a strong and independent predictor for the development of pre-eclampsia (risk ratio, 24.58; 95%CI, 2.82-214.12; p=0.004) as well as gestational diabetes mellitus (risk ratio, 2.07; 95%CI, 1.33-3.22; p=0.001). In this large nested case-control study increased afamin concentrations were a strong and independent predictor for pre-eclampsia and gestational diabetes mellitus, suggesting a potential role of afamin as predictive marker for pregnancy-related metabolic disorders. Copyright © 2017. Published by Elsevier B.V.

Development of radioactive waste treatment technique

International Nuclear Information System (INIS)

Kikuchi, Makoto; Amamiya, Shigeru; Yusa, Hideo.

1984-01-01

The techniques of radioactive waste treatment are generally reviewed, placing emphasis on volume reduction and solidification techniques. After a brief description on the general process of radioactive waste treatment, some special technologies being developed by Hitachi Ltd. are explained. From the viewpoints of the volume reduction, long term management and final disposal of wastes, the pelletization of dried waste and the solidification with inorganic substances are considered. One of the features of the pelletization system is to treat various kinds of wastes such as concentrated liquid wastes and used resins by the same system. The flow diagram of the system and its special features are shown. The volume reduction achieved by this system as compared to the conventional method is about 1/7. The first commercial plant for the treatment of concentrated liquid waste is scheduled to begin operation in June, 1984. As for the solidification technique for waste disposal, the use of cement glass is considered. The solidification system being developed is shortly described. (Aoki, K.)

Workplace immersion in the final year of an undergraduate medicine course: the views of final year students and recent graduates.

Science.gov (United States)

Sen Gupta, Tarun; Hays, Richard; Woolley, Torres; Kelly, Gill; Jacobs, Harry

2014-06-01

Most medical schools require formal competence assessment of students immediately prior to graduation, but variation exists in the approach to endpoint assessments. This article reports perceptions of senior students and graduates from a school with a six-year program which has introduced final year workplace immersion placements following a barrier examination at the end of the penultimate Year 5. Final year students (22) and recent graduates (4) attended focus groups and in-depth interviews exploring their perceptions of the value of the curriculum experience during the final two years, the structure and timing of assessment, and their preparation for internship. Participants felt that the penultimate year was more pressured, and focused on passing "artificial" examinations. In contrast, the final year was more relaxed, building skills for postgraduate work and later career development. As a result, students felt well prepared for internship with some indication that the self-directed nature of the final year promoted a lifelong learning approach. The final year workplace immersion model was regarded positively by senior students of this medical school. This model may be a better way of preparing students to be junior doctors than a traditional final year heavy on theoretical learning and assessment.

Metabolite concentrations in the developing brain estimated with proton MR spectroscopy

DEFF Research Database (Denmark)

Toft, P B; Leth, H; Lou, H C

1995-01-01

(stimulated-echo acquisition mode) sequences with different TEs and TRs. Water was used as an internal standard. The T1 of choline-containing compounds (Cho) and the T1 of phosphocreatine plus creatine (PCr+Cr) decreased. The T2 of the N-acetyl-L-aspartate (NAA) resonance increased, probably because...... of a relatively larger signal overlap with glutamate in the most immature brains. The concentration of NAA almost doubled, whereas the Cho concentration showed only a nonsignificant tendency to decrease; therefore, the well-known increase in the ratio of NAA to Cho appears to be due mostly to an increase in NAA...

Risk factors of methane hydrate resource development in the concentrated zones distributed in the eastern Nankai Trough

Science.gov (United States)

Yamamoto, K.; Nagakubo, S.

2009-04-01

Some environmental and safety concerns on the offshore methane hydrate development have been raised, but the ground of such allegations are sometime not fully reasonable. The risks of methane hydrate resource development to environment and safety should be discussed upon methane hydrate occurrences condition, the production methods, and the designs of production system, under comprehensively scientific manners. In the Phase 1 of the Methane Hydrate Exploitation Program in Japan (FY2001-2008), the Research Consortium for Methane Hydrate Resources in Japan (MH21 Research Consortium) found methane hydrate concentrated zones in the eastern Nankai Trough that are potential prospects for resource development. The concentrated zones are consisted of turbidite-derived sandy sediments and hydrate crystals in pore spaces of sand grains (pore-filling type structure). The MH21 Research Consortium proposed the depressurization method as prime technique due to its efficiency of gas production in such concentrated zones, and has tried to develop conceptual designs of production systems based on the information of existing devices and facilities. Under the condition and circumstances described above, the authors tried to extract and evaluate some risk factors concerning methane hydrate development using depressurization in the area. Leakage of methane gas, that is less harmful substance to ecosystem than heavier hydrocarbons, from production system can be one possible risk. However, in the case of gas production through wellbore, even if catastrophic damages happen in the subsea production system during gas production, the leakages do not continue because the borehole could be filled by seawater and depressurization is stopped immediately. Another possible risk is a leakage of produced gas through seafloor. If methane hydrate production makes high pressure or temperature zones in sediments, the risk should be considered. However, depressurization method makes opposite condition

Development of concentric equipotential surfaces in bumpy torus plasma

International Nuclear Information System (INIS)

Takasugi, Keiichi; Iguchi, Harukazu; Fujiwara, Masami; Ikegami, Hideo

1983-01-01

Radial profiles of the plasma space potential are measured in Nagoya Bumpy Torus (NBT-1) by the use of a heavy ion beam probe. Asymmetric potential profiles owing to toroidal drift are observed in high pressure operation (C-mode). As the pressure is decreased, toroidal plasma is effectively heated (T-mode), poloidal precessional frequency overcomes the electron collision frequency and the equipotential surfaces becomes concentric inside the hot electron ring. (author)

Optimization of fed-batch enzymatic hydrolysis from alkali-pretreated sugarcane bagasse for high-concentration sugar production.

Science.gov (United States)

Gao, Yueshu; Xu, Jingliang; Yuan, Zhenhong; Zhang, Yu; Liu, Yunyun; Liang, Cuiyi

2014-09-01

Fed-batch enzymatic hydrolysis process from alkali-pretreated sugarcane bagasse was investigated to increase solids loading, produce high-concentration fermentable sugar and finally to reduce the cost of the production process. The optimal initial solids loading, feeding time and quantities were examined. The hydrolysis system was initiated with 12% (w/v) solids loading in flasks, where 7% fresh solids were fed consecutively at 6h, 12h, 24h to get a final solids loading of 33%. All the requested cellulase loading (10 FPU/g substrate) was added completely at the beginning of hydrolysis reaction. After 120 h of hydrolysis, the maximal concentrations of cellobiose, glucose and xylose obtained were 9.376 g/L, 129.50 g/L, 56.03 g/L, respectively. The final total glucan conversion rate attained to 60% from this fed-batch process. Copyright © 2014. Published by Elsevier Ltd.

Institut fuer Nukleare Entsorgungstechnik: Status report on research and development 1984

International Nuclear Information System (INIS)

1985-02-01

Some of the main points tackled by the Institute during 1984 included: Testing the glassification technique for radioactive waste and design and construction of a glassification plant; examination of the properties of glass products, testing of incineration of waste containing plutonium; solidification of concentrate containing alpha particles; separation of actinides and fission products from MAW; examination of the release procedures of radio-nuclides from waste solidified with cement; development of long-term containers for the final storage of HAW glass products in salt; model calculations for thermo-mechanical processes and for release mechanisms in final storage. (RB) [de

Development of Prosocial Skills. Final Report

Science.gov (United States)

Parrila, Rauno K.; Ma, Xin; Fleming, Darcy; Rinaldi, Christina

2002-01-01

In part, this focus is a result of substantial research demonstrating strong links between early social competence and later life adjustment and healthy development. The close connection between prosocial skills and a wide variety of future developmental outcomes provides a compelling rationale to examine what factors are associated with…

Modelling daily PM2.5 concentrations at high spatio-temporal resolution across Switzerland.

Science.gov (United States)

de Hoogh, Kees; Héritier, Harris; Stafoggia, Massimo; Künzli, Nino; Kloog, Itai

2018-02-01

Spatiotemporal resolved models were developed predicting daily fine particulate matter (PM 2.5 ) concentrations across Switzerland from 2003 to 2013. Relatively sparse PM 2.5 monitoring data was supplemented by imputing PM 2.5 concentrations at PM 10 sites, using PM 2.5 /PM 10 ratios at co-located sites. Daily PM 2.5 concentrations were first estimated at a 1 × 1km resolution across Switzerland, using Multiangle Implementation of Atmospheric Correction (MAIAC) spectral aerosol optical depth (AOD) data in combination with spatiotemporal predictor data in a four stage approach. Mixed effect models (1) were used to predict PM 2.5 in cells with AOD but without PM 2.5 measurements (2). A generalized additive mixed model with spatial smoothing was applied to generate grid cell predictions for those grid cells where AOD was missing (3). Finally, local PM 2.5 predictions were estimated at each monitoring site by regressing the residuals from the 1 × 1km estimate against local spatial and temporal variables using machine learning techniques (4) and adding them to the stage 3 global estimates. The global (1 km) and local (100 m) models explained on average 73% of the total,71% of the spatial and 75% of the temporal variation (all cross validated) globally and on average 89% (total) 95% (spatial) and 88% (temporal) of the variation locally in measured PM 2.5 concentrations. Copyright © 2017 Elsevier Ltd. All rights reserved.

Population PK modelling and simulation based on fluoxetine and norfluoxetine concentrations in milk: a milk concentration-based prediction model.

Science.gov (United States)

Tanoshima, Reo; Bournissen, Facundo Garcia; Tanigawara, Yusuke; Kristensen, Judith H; Taddio, Anna; Ilett, Kenneth F; Begg, Evan J; Wallach, Izhar; Ito, Shinya

2014-10-01

Population pharmacokinetic (pop PK) modelling can be used for PK assessment of drugs in breast milk. However, complex mechanistic modelling of a parent and an active metabolite using both blood and milk samples is challenging. We aimed to develop a simple predictive pop PK model for milk concentration-time profiles of a parent and a metabolite, using data on fluoxetine (FX) and its active metabolite, norfluoxetine (NFX), in milk. Using a previously published data set of drug concentrations in milk from 25 women treated with FX, a pop PK model predictive of milk concentration-time profiles of FX and NFX was developed. Simulation was performed with the model to generate FX and NFX concentration-time profiles in milk of 1000 mothers. This milk concentration-based pop PK model was compared with the previously validated plasma/milk concentration-based pop PK model of FX. Milk FX and NFX concentration-time profiles were described reasonably well by a one compartment model with a FX-to-NFX conversion coefficient. Median values of the simulated relative infant dose on a weight basis (sRID: weight-adjusted daily doses of FX and NFX through breastmilk to the infant, expressed as a fraction of therapeutic FX daily dose per body weight) were 0.028 for FX and 0.029 for NFX. The FX sRID estimates were consistent with those of the plasma/milk-based pop PK model. A predictive pop PK model based on only milk concentrations can be developed for simultaneous estimation of milk concentration-time profiles of a parent (FX) and an active metabolite (NFX). © 2014 The British Pharmacological Society.

Final disposal of radioactive waste

Directory of Open Access Journals (Sweden)

Freiesleben H.

2013-06-01

Full Text Available In this paper the origin and properties of radioactive waste as well as its classification scheme (low-level waste – LLW, intermediate-level waste – ILW, high-level waste – HLW are presented. The various options for conditioning of waste of different levels of radioactivity are reviewed. The composition, radiotoxicity and reprocessing of spent fuel and their effect on storage and options for final disposal are discussed. The current situation of final waste disposal in a selected number of countries is mentioned. Also, the role of the International Atomic Energy Agency with regard to the development and monitoring of international safety standards for both spent nuclear fuel and radioactive waste management is described.

Program of internal training of the ININ personnel participating in the PERE of the CLV (1998). II. Development and final evaluation

International Nuclear Information System (INIS)

Suarez, G.

1999-04-01

According to the results of the initial evaluation, he/she was carried out the program of the personnel's of the participant ININ internal training in the PERE of the CLV (1998). The purpose of this report is to describe the development of the one it programs and the results of the final evaluation. (Author)

Concentration of Nitrate in Bottled Drinking Water in Qom, Iran

Directory of Open Access Journals (Sweden)

Mohammad Saberi Bidgoli

2013-11-01

Full Text Available Background & Aims of the Study: The global consumption of bottled water is growing with substantial growth in sales volumes on every continent. The highest growth rates are occurring in Asia and South America. Biological and chemical monitoring of these waters is necessary. The aim of current study was determination of nitrate concentration in bottled drinking water in Qom, Iran in 2012. Materials & Methods: A cross-sectional study carried out in Qom, Iran. First of all, 18 most frequent brands of bottled drinking waters were purchased in June 2012 randomly. Then concentration of nitrate was measured according to the spectrophotometric method. In next step, experiment data were analyzed by Excel Software and P value was obtained by statistical calculations. Finally data were comprised with written nitrate concentration on labels and recommended permissible values . Results: The median nitrate concentration was 2.1 mg/L with the minimum 0.8 mg/L and maximum 8.1 mg/L. In 66.7 % of the samples, the measured nitrate concentrations were less than the written nitrate concentrations and in 33.3% of samples, the nitrate concentration was higher. The statistical calculation proved the significant difference between the median of written nitrate concentration on the label and investigated nitrate concentration (P value > 0.05. Conclusions: It be concluded that the measured nitrate concentration in all of the water samples is below the recommended permissible level.

ASBESTOS PIPE-INSULATION REMOVAL ROBOT SYSTEM; FINAL

International Nuclear Information System (INIS)

Unknown

2000-01-01

This final topical report details the development, experimentation and field-testing activities for a robotic asbestos pipe-insulation removal robot system developed for use within the DOE's weapon complex as part of their ER and WM program, as well as in industrial abatement. The engineering development, regulatory compliance, cost-benefit and field-trial experiences gathered through this program are summarized

Ideal flux field dielectric concentrators.

Science.gov (United States)

García-Botella, Angel

2011-10-01

The concept of the vector flux field was first introduced as a photometrical theory and later developed in the field of nonimaging optics; it has provided new perspectives in the design of concentrators, overcoming standard ray tracing techniques. The flux field method has shown that reflective concentrators with the geometry of the field lines achieve the theoretical limit of concentration. In this paper we study the role of surfaces orthogonal to the field vector J. For rotationally symmetric systems J is orthogonal to its curl, and then a family of surfaces orthogonal to the lines of J exists, which can be called the family of surfaces of constant pseudopotential. Using the concept of the flux tube, it is possible to demonstrate that refractive concentrators with the shape of these pseudopotential surfaces achieve the theoretical limit of concentration.

Development of Advanced Ceramic Manufacturing Technology; FINAL

International Nuclear Information System (INIS)

Pujari, V.K.

2001-01-01

Advanced structural ceramics are enabling materials for new transportation engine systems that have the potential for significantly reducing energy consumption and pollution in automobiles and heavy vehicles. Ceramic component reliability and performance have been demonstrated in previous U.S. DOE initiatives, but high manufacturing cost was recognized as a major barrier to commercialization. Norton Advanced Ceramics (NAC), a division of Saint-Gobain Industrial Ceramics, Inc. (SGIC), was selected to perform a major Advanced Ceramics Manufacturing Technology (ACMT) Program. The overall objectives of NAC's program were to design, develop, and demonstrate advanced manufacturing technology for the production of ceramic exhaust valves for diesel engines. The specific objectives were (1) to reduce the manufacturing cost by an order of magnitude, (2) to develop and demonstrate process capability and reproducibility, and (3) to validate ceramic valve performance, durability, and reliability. I n order to achieve these objectives, NAC, a leading U.S. advanced ceramics component manufacturer, assembled a multidisciplinary, vertically integrated team. This team included: a major diesel engine builder, Detroit Diesel Corporation (DDC); a corporate ceramics research division, SGIC's Northboro R and D Center; intelligent processing system developers, BDM Federal/MATSYS; a furnace equipment company, Centorr/Vacuum Industries; a sintering expert, Wittmer Consultants; a production OEM, Deco-Grand; a wheel manufacturer and grinding operation developer, Norton Company's Higgins Grinding Technology Center (HGTC); a ceramic machine shop, Chand Kare Technical Ceramics; and a manufacturing cost consultant, IBIS Associates. The program was divided into four major tasks: Component Design and Specification, Component Manufacturing Technology Development, Inspection and Testing, and Process Demonstration

Environmental effects of marine energy development around the world. Annex IV Final Report

Energy Technology Data Exchange (ETDEWEB)

Copping, Andrea; Hanna, Luke; Whiting, Johnathan; Geerlofs, Simon; Grear, Molly; Blake, Kara [Pacific Northwest National Laboratory, Richland, WA (United States); Coffey, Anna; Massaua, Meghan; Brown-Saracino, Jocelyn; Battey, Hoyt [US Dept. of Energy, Washington, DC (United States)

2013-01-15

Annex IV is an international collaborative project to examine the environmental effects of marine energy devices among countries through the International Energy Agency’s Ocean Energy Systems Initiative (OES). The U.S. Department of Energy (DOE) serves as the Operating Agent for the Annex, in partnership with the Bureau of Ocean Energy Management (BOEM; formerly the Minerals Management Service), the Federal Energy Regulatory Commission (FERC), and National Oceanographic and Atmospheric Administration (NOAA). Numerous ocean energy technologies and devices are being developed around the world, and the few data that exist about the environmental effects of these technologies are dispersed among countries and developers. The purpose of Annex IV is to facilitate efficient government oversight of the development of ocean energy systems by compiling and disseminating information about the potential environmental effects of marine energy technologies and to identify methods of monitoring for these effects. Beginning in 2010, this three-year effort produced a publicly available searchable online database of environmental effects information (Tethys). It houses scientific literature pertaining to the environmental effects of marine energy systems, as well as metadata on international ocean energy projects and research studies. Two experts’ workshops were held in Dublin, Ireland (September 2010 and October 2012) to engage with international researchers, developers, and regulators on the scope and outcomes of the Annex IV project. Metadata and information stored in the Tethys database and feedback obtained from the two experts’ workshops were used as resources in the development of this report. This Annex IV final report contains three case studies of specific interactions of marine energy devices with the marine environment that survey, compile, and analyze the best available information in one coherent location. These case studies address 1) the physical interactions

A near-peer teaching program designed, developed and delivered exclusively by recent medical graduates for final year medical students sitting the final objective structured clinical examination (OSCE

Directory of Open Access Journals (Sweden)

Sobowale Oluwaseun

2011-03-01

Full Text Available Abstract Background The General Medical Council states that teaching doctors and students is important for the care of patients. Our aim was to deliver a structured teaching program to final year medical students, evaluate the efficacy of teaching given by junior doctors and review the pertinent literature. Methods We developed a revision package for final year medical students sitting the Objective Structured Clinical Examination (OSCE. The package was created and delivered exclusively by recent medical graduates and consisted of lectures and small group seminars covering the core areas of medicine and surgery, with a focus on specific OSCE station examples. Students were asked to complete a feedback questionnaire during and immediately after the program. Results One hundred and eighteen completed feedback questionnaires were analysed. All participants stated that the content covered was relevant to their revision. 73.2% stated that junior doctors delivered teaching that is comparable to that of consultant - led teaching. 97.9% stated the revision course had a positive influence on their learning. Conclusions Our study showed that recent medical graduates are able to create and deliver a structured, formal revision program and provide a unique perspective to exam preparation that was very well received by our student cohort. The role of junior doctors teaching medical students in a formal structured environment is very valuable and should be encouraged.

Paracetamol (acetaminophen) protein adduct concentrations during therapeutic dosing.

Science.gov (United States)

Heard, Kennon; Green, Jody L; Anderson, Victoria; Bucher-Bartelson, Becki; Dart, Richard C

2016-03-01

Paracetamol protein adducts (PPA) are a biomarker of paracetamol exposure. PPA are quantified as paracetamol-cysteine (APAP-CYS), and concentrations above 1.1 μmol l(-1) have been suggested as a marker of paracetamol-induced hepatotoxicity. However, there is little information on the range of concentrations observed during prolonged therapeutic dosing. The aim of the present study was to describe the concentration of PPA in the serum of subjects taking therapeutic doses of paracetamol for at least 16 days. Preplanned secondary aim of a prospective randomized controlled (placebo vs. 4g day(-1) paracetamol) trial. We measured subjects' serum PPA concentrations every 3 days for a minimum of 16 days. We also measured concentrations on study days 1-3 and 16-25 in subsets of patients. PPA were quantified as APAP-CYS after gel filtration and protein digestion using liquid chromatography/mass spectrometry. Ninety per cent of subjects had detectable PPA after five doses. Median APAP-CYS concentrations in paracetamol-treated subjects increased to a plateau of 0.1 μmol l(-1) on day 7, where they remained. The highest concentration measured was 1.1 μmol l(-1) and two subjects never had detectable PPA levels. PPA were detected in the serum of 78% of subjects 9 days after their final dose. PPA are detectable in the vast majority of subjects taking therapeutic doses of paracetamol. While most have concentrations well below the threshold associated with hepatotoxicity, concentrations may approach 1.1 μmol l(-1) in rare cases. Adducts are detectable after a few doses and can persist for over a week after dosing is stopped. © 2015 The British Pharmacological Society.

Development of a software for INAA analysis automation

International Nuclear Information System (INIS)

Zahn, Guilherme S.; Genezini, Frederico A.; Figueiredo, Ana Maria G.; Ticianelli, Regina B.

2013-01-01

In this work, a software to automate the post-counting tasks in comparative INAA has been developed that aims to become more flexible than the available options, integrating itself with some of the routines currently in use in the IPEN Activation Analysis Laboratory and allowing the user to choose between a fully-automatic analysis or an Excel-oriented one. The software makes use of the Genie 2000 data importing and analysis routines and stores each 'energy-counts-uncertainty' table as a separate ASCII file that can be used later on if required by the analyst. Moreover, it generates an Excel-compatible CSV (comma separated values) file with only the relevant results from the analyses for each sample or comparator, as well as the results of the concentration calculations and the results obtained with four different statistical tools (unweighted average, weighted average, normalized residuals and Rajeval technique), allowing the analyst to double-check the results. Finally, a 'summary' CSV file is also produced, with the final concentration results obtained for each element in each sample. (author)

Different conformational forms of serum carnosinase detected by a newly developed sandwich ELISA for the measurements of carnosinase concentrations

NARCIS (Netherlands)

Adelmann, Katja; Frey, Dirk; Riedl, Eva; Koeppel, Hannes; Pfister, Frederick; Peters, Verena; Schmitt, Claus P.; Sternik, Paula; Hofmann, Stephanie; Zentgraf, Hans Walter; Navis, Gerjan; van den Born, Jacob; Bakker, Stephan J. L.; Kraemer, Bernhard K.; Yard, Benito A.; Hauske, Sibylle J.

Serum carnosinase (CN-1) measurements are at present mainly performed by assessing enzyme activity. This method is time-consuming, not well suited for large series of samples and can be discordant to measurements of CN-1 protein concentrations. To overcome these limitations, we developed sandwich

Structural concepts for very large (400-meter-diameter) solar concentrators

Science.gov (United States)

Mikulas, Martin M., Jr.; Hedgepeth, John M.

1989-01-01

A general discussion of various types of large space structures is presented. A brief overview of the history of space structures is presented to provide insight into the current state-of-the art. Finally, the results of a structural study to assess the viability of very large solar concentrators are presented. These results include weight, stiffness, part count, and in-space construction time.

Biogas final digestive byproduct applied to croplands as fertilizer contains high levels of steroid hormones

International Nuclear Information System (INIS)

Rodriguez-Navas, Carlos; Björklund, Erland; Halling-Sørensen, Bent; Hansen, Martin

2013-01-01

In this study we evaluate and demonstrate the occurrence of nine natural and one synthetic steroid hormone, including estrogens, androgens and progestagens in biogas final digestate byproduct (digestion liquid) commonly used as an agricultural fertilizer. We investigated two biogas sites that utilize different anaerobic digestion technologies (mesophilic and thermophilic) from swine manure and other organic wastes. Individual hormone concentration levels were observed up to 1478 ng g −1 dry weight or 22.5 mg kg −1 N with estrone and progesterone reaching highest concentration levels. Evaluation of the potential environmental burden through the application in agriculture was also assessed on the basis of predicted environmental concentrations. This study indicates that the biogas digestion process does not completely remove steroid hormones from livestock manure and use of final digestate byproduct on croplands contributes to the environmental emission of hormones. -- Eight steroid hormones were found in biogas digestate byproduct in the ng g −1 dm levels. Anaerobic digestion processes do not completely remove steroid hormones from organic waste residues

Developing on-site paper colorimetric monitoring technique for quick evaluating copper ion concentration in mineral wastewater

Science.gov (United States)

Liu, Guokun; Peng, Jingji; Zheng, Hong; Yuan, Dongxing

2018-05-01

With the reinforce of the copper mining, the on-site monitoring of the accompanied effluent discharge is highly demanded for the emergency response to minimize the negative effect of the effluent on the surrounding ecosystem. On the basis of the specific interaction between Cu2+ and L-Cysteine (L-Cys), which was modified on gold nanoparticles (Au NPs), and the aggregation dependent surface plasmon resonance (SPR) of Au NPs, we developed an easy-on-going paper colorimetric method for the quick evaluating the copper ion concentration in the waste water excreted from the copper mine. The color change of L-Cys modified Au NPs (L-Cys-Au NPs)immobilized on a filter paper was very sensitive to the Cu2+ concentration and free of interference from other metal ions typically in waste water. The proposed paper colorimetry has the LOD of 0.09 mg/L and the linear range of 0.1-10 mg/L, respectively, with the RSD (n = 5) was 6.6% for 1 mg/L Cu2+ and 3.5% for 5 mg/L Cu2+. The quantitative analysis results for the mineral wastewater is in good agreement the China National Environmental Protection Standards HJ485-2009, which indicates the current method could be developed to the on-site detection technique for the emergency response in monitoring Cu2+ in industrial wastewater or polluted water.

Achievement Motivation Development Project. Final Report.

Science.gov (United States)

McClelland, Dave C.; Alschuler, Alfred S.

Two efforts were made to develop achievement motivation in school children and to observe the effect of such training on their behavior in and out of school. These studies were undertaken because: (1) Achievement motivation might help children think more seriously about their work habits and career planning; (2) It might improve the grades of…

On the theory of direct reactions with many particle final states

International Nuclear Information System (INIS)

Trautmann, D.; Baur, G.

1977-01-01

We study the theory of direct reactions with many particle final states. First, we concentrate on the DWBA formulation of the break-up of deuterons on heavy nuclei below the Coulomb barrier. Because there are no free parameters, this permits a clean test of the theory by comparing it to the experimental data. The agreement is very good. The theory is applied to the break-up of antideuteronic atoms. Then the effect of virtual deuteron break-up on Rutherford scattering is studied. It is small, but it seems to be measurable. Also the deuteron break-up above the Coulomb barrier can be well explained theoretically. In this context, small effects are studied briefly. A semiclassical theory of the break-up process is given, which results in an intuitive picture and a fast computational method. Our theory lends itself in a natural way to the study of stripping reactions to unbound states. The relation of stripping into the continuum to elastic scattering of the transferred particle on the same target nucleus is explained. Then the connection of stripping to bound and unbound states is established. Finally various examples of stripping of uncharged and charged particles into the continuum are given to illustrate the theory. Resonance wave functions describing the transferred particle are discussed. In a conclusion an outlook for possible future developments of experiment and theory is given. (author)

Cystatin C and lactoferrin concentrations in biological fluids as possible prognostic factors in eye tumor development

Directory of Open Access Journals (Sweden)

Mariya A. Dikovskaya

2013-08-01

Full Text Available Objectives. To investigate the possible role of cystatin C in eye biological fluids locally and in serum and lactoferrin revealing anti-tumor activity in eye tumor development. Background. The increased number of eye tumors was registered recently not only in the countries with high insolation, but also in the northern countries including Russia (11 cases per million of population. Search for new biological markers is important for diagnosis and prognosis in eye tumors. Cystatin C, an endogenous inhibitor of cysteine proteases, plays an important protective role in several tumors. Lactoferrin was shown to express anti-tumor and antiviral activities. It was hypothesized that cystatin C and lactoferrin could serve as possible biomarkers in the diagnosis of malignant and benign eye tumors. Study design. A total of 54 patients with choroidal melanoma and benign eye tumors were examined (part of them undergoing surgical treatment. Serum, tear fluid and intraocular fluid samples obtained from the anterior chamber of eyes in patients with choroidal melanoma were studied. Methods. Cystatin C concentration in serum and eye biological fluids was measured by commercial ELISA kits for human (BioVendor, Czechia; lactoferrin concentration – by Lactoferrin-strip D 4106 ELISA test systems (Vector-BEST, Novosibirsk Region, Russia. Results. Cystatin C concentration in serum of healthy persons was significantly higher as compared to tear and intraocular fluids. In patients with choroidal melanoma, increased cystatin C concentration was similar in tear fluid of both the eyes. Lactoferrin level in tear fluid of healthy persons was significantly higher than its serum level. Significantly increased lactoferrin concentration in tear fluid was noted in patients with benign and malignant eye tumors. Conclusion. Increased level of cystatin C in tear fluid seems to be a possible diagnostic factor in the eye tumors studied. However, it does not allow us to differentiate

Separation and Concentration without Clogging Using a High-Throughput Tunable Filter

Science.gov (United States)

Mossige, E. J.; Jensen, A.; Mielnik, M. M.

2018-05-01

We present a detailed experimental study of a hydrodynamic filtration microchip and show how chip performance can be tuned and clogging avoided by adjusting the flow rates. We demonstrate concentration and separation of microspheres at throughputs as high as 29 ml /min and with 96% pureness. Results of streakline visualizations show that the thickness of a tunable filtration layer dictates the cutoff size and that two different concentration mechanisms exist. Particles larger than pores are concentrated by low-velocity rolling over the filtration pillars, while particles smaller than pores are concentrated by lateral drift across the filtration layer. Results of microscopic particle image velocimetry and particle-tracking velocimetry show that the degree of lateral migration can be quantified by the slip velocity between the particle and the surrounding fluid. Finally, by utilizing differences in inertia and separation mode, we demonstrate size-based separation of particles in a mixture.

Developed methodology for the geologic control of the secondary uranium concentrations in Osamu Utsumi, Pocos de Caldas (MG)

International Nuclear Information System (INIS)

Magno Junior, L.B.

1982-01-01

It was developed a methodology for the geologic control of the mining of the secondary uranium concentrations in the Osamu Utsumi mine, Pocos de Caldas. A sequential systematization with the definitions and objectives of the operational phases of the mining explotation is shown, in addition of a scheme and flow charts of them. (A.B.) [pt

Surface and subsurface cleanup protocol for radionuclides, Gunnison, Colorado, UMTRA project processing site: Final

International Nuclear Information System (INIS)

1994-01-01

Thorium 230 (Th-230) at the Gunnison, Colorado processing site will require remediation, however, a seasonally fluctuating groundwater table at the site significantly complicates conventional remedial action with respect to cleanup. Therefore, to effectively remediate the site with respect to Radium 226 (Ra-226) and Th-230, the following supplemental standard is proposed: In situ Ra-26 will be remediated to the EPA soil cleanup standards independent of groundwater considerations. In situ Th-230 concentrations will be remediated in the region above the encountered water table so the 1000-year projected Ra-226 concentration complies with the EPA soil cleanup concentration limits. If elevated Th-230 persists to the water table, an additional foot of excavation will be performed and the grid will be backfilled. Excavated grids will be backfilled to the final remedial action grade with clean cobbly soil. Final grid verification that is required below the water table will be performed by extracting and analyzing a single bulk soil sample with the bucket of a backhoe. Modeled surface radon flux values will be estimated and documented. A recommendation will be made that land records should be annotated to identify the presence of residual Th-230

The concentration and type of liquid smoke to suppress the development of Elsinoe fawcettii causing scab on citrus plant of Japansche citroen

Directory of Open Access Journals (Sweden)

Triwiratno A.

2018-04-01

Full Text Available Citrus is the main fruit commodity in Indonesia. Scab disease is a major disease in citrus plants. Scab disease control usually uses chemical fungicides that cause environmental pollution. Liquid smoke is a natural substance as a safer fungicide. The objective of this study was to analyze the ability of liquid smoke with the most effective concentration of three types of liquid smoke ie coconut shell, teak and falcata in suppressing the development of fungus Elsinoe fawcettii in citrus Japansche Citroen (JC. The identification and treatment carried out were analysis of phenol compounds contained in three types of liquid smoke (coconut shell, teak and falcata wood, testing of in vitro antifungal properties on growth of fungus E. fawcettii isolate in petri and in vivo sprouts against disease rate scab on JC citrus plant. The results showed that phenol content of coconut shell liquid smoke was 62.747 ml / L, 227.873 ml / L of teak wood and falcata wood was 115.587 ml / L. On observation of E. fawcettii fungal colony 14 days after inocculation (dai highest percentage inhibition was smoke falcata smoke 5% concentration, able to inhibit growth of E. fawcettii equal to 77,22% whereas the lowest concentration was coconut shell smoke concentration 2% with 10.14% inhibition rate. Observation of wet weight and dry weight of E. fawcetti result of falcata smoke smoke treatment of 5% and 1% concentration have the lowest wet weight and dry weight of 0.867 g and 0.030 g, while on observation of intensity and extent of disease attack in vivo treatment of liquid smoke shell coconut wood and falcata wood have almost the same level of effectiveness. The conclusions of this study indicate that three types of liquid smoke ie coconut shell, teak and falcata wood have the ability to suppress growth and development of E. fawcetti fungus both in vitro and in vivo, while the most effective type is falcata wood. The most effective concentration in suppressing growth and

Development of a Modular Laboratory Information Management System (LIMS) for NAA Laboratories Using Open-Source Developing Tools

International Nuclear Information System (INIS)

Bounakhla, Moussa; Amsil, Hamid; Embarch, K.; Bounouira, Hamid

2018-01-01

CNESTEN designed and developed a modular Laboratory Information Management System (LIMS) for the NAA Laboratory using open-source developing tools. This LIMS ensures a personalized management web space for sample acquisition and preparation, spectra processing and for final analysis of the sample. The system helps also dematerializing process for irradiation requests and for the acquisition of new equipments and samples. It allows managing circulating documents between different actors of the LIMS. Modules for concentration determination, facilities characterization are also included in this LIMS. New modules such as spectra fitting, true coincidence and attenuation corrections can be developed and integrated individually in this system. All data, including nuclear data libraries, are stored in a unique distant database via intranet network to allow instantaneous multi-user access. (author)

Continuous measurements of outdoor radon concentrations

International Nuclear Information System (INIS)

Iida, T.; Ikebe, Y.; Suzuki, K.; Ueno, K.; Komura, K.; Kato, I.; Jin Yihe

1993-01-01

The authors studied and developed an electrostatic 222 Rn monitor and have measured continuously outdoor radon ( 222 Rn) concentrations at Nagoya University since 1985. Four 222 Rn monitors were newly constructed to measure outdoor 222 Rn concentrations at other locations. The 222 Rn concentrations at Nagoya and Kasugai show a clear diurnal variation in autumn, and a seasonal pattern of a spring-summer minimum and a autumn-winter maximum. The results at Toki are the same pattern as that at Nagoya except spring. The concentrations at Kanazawa show a slight seasonal variation. A clear diurnal variation is observed in summer. (4 figs.)

Advertising and Concentration in the Brewing Industry

DEFF Research Database (Denmark)

Madsen, Erik Strøjer; Wu, Yanqing

2014-01-01

The paper tracks the development in industry concentrations from 2002 to 2012, discusses some of the main drivers behind this development and points to economies of scale in advertising as a main pay-off from mergers and acquisitions. Using firm-level data both from the American market and the wo......The paper tracks the development in industry concentrations from 2002 to 2012, discusses some of the main drivers behind this development and points to economies of scale in advertising as a main pay-off from mergers and acquisitions. Using firm-level data both from the American market...

New method of design of nonimaging concentrators.

Science.gov (United States)

Miñano, J C; González, J C

1992-06-01

A new method of designing nonimaging concentrators is presented and two new types of concentrators are developed. The first is an aspheric lens, and the second is a lens-mirror combination. A ray tracing of three-dimensional concentrators (with rotational symmetry) is also done, showing that the lens-mirror combination has a total transmission as high as that of the full compound parabolic concentrators, while their depth is much smaller than the classical parabolic mirror-nonimaging concentrator combinations. Another important feature of this concentrator is that the optically active surfaces are not in contact with the receiver, as occurs in other nonimaging concentrators in which the rim of the mirror coincides with the rim of the receiver.

Development of a high-density gas-jet target for nuclear astrophysics and reaction studies with rare isotope beams. Final Report

Energy Technology Data Exchange (ETDEWEB)

Uwe, Greife [Colorado School of Mines, Golden, CO (United States)

2014-08-12

The purpose of this project was to develop a high-density gas jet target that will enable a new program of transfer reaction studies with rare isotope beams and targets of hydrogen and helium that is not currently possible and will have an important impact on our understanding of stellar explosions and of the evolution of nuclear shell structure away from stability. This is the final closeout report for the project.

Development of a high-density gas-jet target for nuclear astrophysics and reaction studies with rare isotope beams. Final Report

International Nuclear Information System (INIS)

Uwe, Greife

2014-01-01

The purpose of this project was to develop a high-density gas jet target that will enable a new program of transfer reaction studies with rare isotope beams and targets of hydrogen and helium that is not currently possible and will have an important impact on our understanding of stellar explosions and of the evolution of nuclear shell structure away from stability. This is the final closeout report for the project.

Sedimentation Characteristics of Kaolin and Bentonite in Concentrated Solutions

Directory of Open Access Journals (Sweden)

Abdulah Obut

2005-11-01

Full Text Available The sedimentation characteristics of two clays, namely kaolinite and bentonite, were determinated at high clay (5 % wt/vol and electrolyte (1 N concentrations using various inorganic-organic compounds. It was observed that the settling behaviour of kaolinite (1:1 clay and montmorillonite (2:1 clay is quite different due to the structural differences between these minerals. Although, similar initial settling rates and final sediment volumes were obtained after 24 hours of settling time for kaolin suspensions, the corresponding rates and volumes for bentonite suspensions varied greatly with the used chemical compound. According to the experimental results, a further intensive theoretical and experimental investigation is needed to reveal the mechanism underlying the sedimentation characteristics of clay minerals at high clay and electrolyte concentrations.

Traceability and communication of requirements in digital I and C systems development. Final report

Energy Technology Data Exchange (ETDEWEB)

Sivertsen, T.; Fredriksen, Rune; Thunem, A.P.J. [Inst. for Energy Technology, Halden (Norway); Holmberg, J.E.; Valkonen, J.; Ventae, O. [VTT (Finland); Andersson, J.O. [Ringhals AB (Sweden)

2005-10-01

The overall objective of the TACO project has been to improve the knowledge on principles and best practices related to the traceability and communication of requirements in digital I and C systems development. On the basis of experiences in the Nordic countries, the project has aimed at identifying the best practices and most important criteria for ensuring effective communication in relation to requirements elicitation and analysis, understandability of requirements to all parties, and traceability of requirements through the different design phases. It is expected that the project will provide important input to the development of guidelines and establishment of recommended practices related to these activities. The report provides a summary of the project activities and deliverables, discusses possible application areas, and provides a link to its utilization in the project 'Management of Requirements in NPP Modernization Projects' (NKS-R-2005-47). In the preparation of the final report, a number of application areas have been identified where the TACO deliverables, first of all the TACO Shell and the TACO Traceability Model, can be utilized. The report aims at facilitating such utilization, by defining the context and main issues, explaining the main aspects of the deliverables, discussing the challenges experienced in the different application domains with respect requirements management, traceability and communication and how can the TACO results contribute to solving these challenges. (au)

Traceability and communication of requirements in digital I and C systems development. Final report

International Nuclear Information System (INIS)

Sivertsen, T.; Fredriksen, Rune; Thunem, A.P.J.; Holmberg, J.E.; Valkonen, J.; Ventae, O.; Andersson, J.O.

2005-10-01

The overall objective of the TACO project has been to improve the knowledge on principles and best practices related to the traceability and communication of requirements in digital I and C systems development. On the basis of experiences in the Nordic countries, the project has aimed at identifying the best practices and most important criteria for ensuring effective communication in relation to requirements elicitation and analysis, understandability of requirements to all parties, and traceability of requirements through the different design phases. It is expected that the project will provide important input to the development of guidelines and establishment of recommended practices related to these activities. The report provides a summary of the project activities and deliverables, discusses possible application areas, and provides a link to its utilization in the project 'Management of Requirements in NPP Modernization Projects' (NKS-R-2005-47). In the preparation of the final report, a number of application areas have been identified where the TACO deliverables, first of all the TACO Shell and the TACO Traceability Model, can be utilized. The report aims at facilitating such utilization, by defining the context and main issues, explaining the main aspects of the deliverables, discussing the challenges experienced in the different application domains with respect requirements management, traceability and communication and how can the TACO results contribute to solving these challenges. (au)

Development of a new osmium-191: Iridium-191m radionuclide generator: Final report

International Nuclear Information System (INIS)

Treves, S.; Packard, A.B.

1986-01-01

The use of iridium-191m (T/sub 1/2/ = 5s) for first-pass radionuclide angiography offers the potential advantages of lower patient radiation dose and the ability to obtain repeated studies without interference from the previously administered radioisotope. These potential advantages have been offset by the absence of satisfactory 191 Os-/sup 191m/Ir generators. The goal of this project was, therefore, the development of an 191 Os-/sup 191m/Ir generator that would be suitable for clinical use. This goal was first sought through modifications of an existing 191 Os-/sup 191m/Ir generator design (i.e., changes in the ion exchange material and eluent) but these changes did not lead to the required improvements. A new approach was then undertaken in which different chemical forms of the 191 Os parent were evaluated in prototype generators. The complex trans-dioxobisoxalatoosmate (VI) led to a generator with higher /sup 191m/Ir yield (25 to 30%/mL) and lower 191 Os breakthrough ( -4 %) with a more physiologically compatible eluent than had been previously achieved. Toxicity studies were conducted on the eluate and an IND subsequently obtained. While this is not a final solution to the problem of developing a clinically acceptable 191 Os-/sup 191m/Ir generator, the ''oxalate'' generator is the most significant improvement of the 191 Os-/sup 191m/Ir generator to date and will be used in an expanded program of clinical studies. 16 refs., 16 tabs

In-Situ Radiation Detection Demonstration Final Report

International Nuclear Information System (INIS)

Mohagheghi, Amir H.; Reese, Robert; Miller, David R.; Miller, Mark Laverne; Duce, Stephen

2000-01-01

The Department of Defense (DoD) has hundreds of facilities where radioactive materials have been used or are being used, including firing ranges, low-level radioactive waste disposal areas, and areas where past activities have resulted in environmental contamination. Affected sites range in size from a few acres to square miles. Impact to the DoD comes through military base closure and release to the public. It is important that radioactive contaminants are remediated to levels that result in acceptable risk to the public. Remediation requires characterization studies, e.g., sampling and surveys, to define the affected areas, removal actions, and final confirmatory sampling and surveys. Characterization of surface contamination concentrations has historically been performed using extensive soil sampling programs in conjunction with surface radiation surveys conducted with hand-held radiation monitoring equipment. Sampling is required within the suspect affected area and a large buffer area. Surface soil contaminant characterization using soil sampling and hand held monitoring are costly, time consuming, and result in long delays between submission of samples for analysis and obtaining of final results. This project took an existing, proven radiation survey technology that has had limited exposure and improved its capabilities by documenting correlation factors for various detector/radionuclide geometries that commonly occur in field surveys. With this tool, one can perform characterization and final release surveys much more quickly than is currently possible, and have detection limits that are as good as or better than current technology. This paper will discuss the capabilities of a large area plastic scintillation detector used in conjunction with a global positioning system (GPS) to improve site characterization, remediation, and final clearance surveys of the radioactively contaminated site. Survey results can rapidly identify areas that require remediation as

Development of a coal fired pulse combustor for residential space heating. Phase I, Final report

Energy Technology Data Exchange (ETDEWEB)

NONE

1988-04-01

This report presents the results of the first phase of a program for the development of a coal-fired residential combustion system. This phase consisted of the design, fabrication, testing, and evaluation of an advanced pulse combustor sized for residential space heating requirements. The objective was to develop an advanced pulse coal combustor at the {approximately} 100,000 Btu/hr scale that can be integrated into a packaged space heating system for small residential applications. The strategy for the development effort included the scale down of the feasibility unit from 1-2 MMBtu/hr to 100,000 Btu/hr to establish a baseline for isolating the effect of scale-down and new chamber configurations separately. Initial focus at the residential scale was concentrated on methods of fuel injection and atomization in a bare metal unit. This was followed by incorporating changes to the advanced chamber designs and testing of refractory-lined units. Multi-fuel capability for firing oil or gas as a secondary fuel was also established. Upon completion of the configuration and component testing, an optimum configuration would be selected for integrated testing of the pulse combustor unit. The strategy also defined the use of Dry Ultrafine Coal (DUC) for Phases 1 and 2 of the development program with CWM firing to be a product improvement activity for a later phase of the program.

Proximity sensor system development. CRADA final report

Energy Technology Data Exchange (ETDEWEB)

Haley, D.C. [Oak Ridge National Lab., TN (United States); Pigoski, T.M. [Merrit Systems, Inc. (United States)

1998-01-01

Lockheed Martin Energy Research Corporation (LMERC) and Merritt Systems, Inc. (MSI) entered into a Cooperative Research and Development Agreement (CRADA) for the development and demonstration of a compact, modular proximity sensing system suitable for application to a wide class of manipulator systems operated in support of environmental restoration and waste management activities. In teleoperated modes, proximity sensing provides the manipulator operator continuous information regarding the proximity of the manipulator to objects in the workspace. In teleoperated and robotic modes, proximity sensing provides added safety through the implementation of active whole arm collision avoidance capabilities. Oak Ridge National Laboratory (ORNL), managed by LMERC for the United States Department of Energy (DOE), has developed an application specific integrated circuit (ASIC) design for the electronics required to support a modular whole arm proximity sensing system based on the use of capacitive sensors developed at Sandia National Laboratories. The use of ASIC technology greatly reduces the size of the electronics required to support the selected sensor types allowing deployment of many small sensor nodes over a large area of the manipulator surface to provide maximum sensor coverage. The ASIC design also provides a communication interface to support sensor commands from and sensor data transmission to a distributed processing system which allows modular implementation and operation of the sensor system. MSI is a commercial small business specializing in proximity sensing systems based upon infrared and acoustic sensors.

Proximity sensor system development. CRADA final report

International Nuclear Information System (INIS)

Haley, D.C.; Pigoski, T.M.

1998-01-01

Lockheed Martin Energy Research Corporation (LMERC) and Merritt Systems, Inc. (MSI) entered into a Cooperative Research and Development Agreement (CRADA) for the development and demonstration of a compact, modular proximity sensing system suitable for application to a wide class of manipulator systems operated in support of environmental restoration and waste management activities. In teleoperated modes, proximity sensing provides the manipulator operator continuous information regarding the proximity of the manipulator to objects in the workspace. In teleoperated and robotic modes, proximity sensing provides added safety through the implementation of active whole arm collision avoidance capabilities. Oak Ridge National Laboratory (ORNL), managed by LMERC for the United States Department of Energy (DOE), has developed an application specific integrated circuit (ASIC) design for the electronics required to support a modular whole arm proximity sensing system based on the use of capacitive sensors developed at Sandia National Laboratories. The use of ASIC technology greatly reduces the size of the electronics required to support the selected sensor types allowing deployment of many small sensor nodes over a large area of the manipulator surface to provide maximum sensor coverage. The ASIC design also provides a communication interface to support sensor commands from and sensor data transmission to a distributed processing system which allows modular implementation and operation of the sensor system. MSI is a commercial small business specializing in proximity sensing systems based upon infrared and acoustic sensors

Thermodynamic efficiency of solar concentrators.

Science.gov (United States)

Shatz, Narkis; Bortz, John; Winston, Roland

2010-04-26

The optical thermodynamic efficiency is a comprehensive metric that takes into account all loss mechanisms associated with transferring flux from the source to the target phase space, which may include losses due to inadequate design, non-ideal materials, fabrication errors, and less than maximal concentration. We discuss consequences of Fermat's principle of geometrical optics and review étendue dilution and optical loss mechanisms associated with nonimaging concentrators. We develop an expression for the optical thermodynamic efficiency which combines the first and second laws of thermodynamics. As such, this metric is a gold standard for evaluating the performance of nonimaging concentrators. We provide examples illustrating the use of this new metric for concentrating photovoltaic systems for solar power applications, and in particular show how skewness mismatch limits the attainable optical thermodynamic efficiency.

Phytophthora quercina infections in elevated CO2 concentrations

Directory of Open Access Journals (Sweden)

Oszako Tomasz

2016-09-01

Full Text Available In the last decades, a new wave of oak decline has been observed in Poland. The most important pathogenic organisms involved in this phenomenon are probably soil-borne pathogens Phytophthoragenus, especially P. quercina. In this work, we sought to test the influence of elevated CO2 concentration on the susceptibility of oaks (Quercus robur L. to infection by P. quercina. In order to test the susceptibility of oak fine roots to infection, we applied phosphite-based fertiliser Actifos in 0.6% concentration. One-year-old oak seedlings were grown for one year in greenhouse with either an ambient atmosphere (400 ppm CO2 or an elevated (800 ppm concentration of CO2. Oaks grown at the elevated CO2 concentration developed longer shoots as proved by statistically significant differences. However, there was no difference in the development of root systems. The application of Actifos had a positive significant effect on the development of shoots and the surface area of fine roots under the elevated CO2 concentration.

Association between outcome and changes in plasma lactate concentration during presurgical treatment in dogs with gastric dilatation-volvulus: 64 cases (2002-2008).

Science.gov (United States)

Zacher, Laurie A; Berg, John; Shaw, Scott P; Kudej, Raymond K

2010-04-15

To determine whether changes in presurgical plasma lactate concentration (before and after initial fluid resuscitation and gastric decompression) were associated with short-term outcome for dogs with gastric dilatation-volvulus (GDV). Retrospective case series. 64 dogs. Medical records were reviewed, and signalment, history, resuscitative treatments, serial presurgical lactate concentrations, surgical findings, and short-term outcome were obtained for dogs with confirmed GDV. 36 of 40 (90%) dogs with an initial lactate concentration dogs with a high initial lactate (HIL) concentration (> 9.0 mmol/L). Within HIL dogs, there was no difference in mean +/- SD initial lactate concentration between survivors and nonsurvivors (10.6 +/- 2.3 mmol/L vs 11.2 +/- 2.3 mmol/L, respectively); however, there were significant differences in post-treatment lactate concentration, absolute change in lactate concentration, and percentage change in lactate concentration following resuscitative treatment. By use of optimal cutoff values within HIL dogs, survival rates for dogs with final lactate concentration > 6.4 mmol/L (23%), absolute change in lactate concentration dogs with a final lactate concentration 4 mmol/L (86%), or percentage change in lactate concentration > 42.5% (100%). Calculating changes in plasma lactate concentration following initial treatment in dogs with GDV may assist in determining prognosis and identifying patients that require more aggressive treatment.

Reflector Technology Development and System Design for Concentrating Solar Power Technologies

Energy Technology Data Exchange (ETDEWEB)

Adam Schaut

2011-12-30

Alcoa began this program in March of 2008 with the goal of developing and validating an advanced CSP trough design to lower the levelized cost of energy (LCOE) as compared to existing glass based, space-frame trough technology. In addition to showing a pathway to a significant LCOE reduction, Alcoa also desired to create US jobs to support the emerging CSP industry. Alcoa's objective during Phase I: Concept Feasibility was to provide the DOE with a design approach that demonstrates significant overall system cost savings without sacrificing performance. Phase I consisted of two major tasks; reflector surface development and system concept development. Two specific reflective surface technologies were investigated, silver metallized lamination, and thin film deposition both applied on an aluminum substrate. Alcoa prepared samples; performed test validation internally; and provided samples to the NREL for full-spectrum reflectivity measurements. The final objective was to report reflectivity at t = 0 and the latest durability results as of the completion of Phase 1. The target criteria for reflectance and durability were as follows: (1) initial (t = 0), hemispherical reflectance >93%, (2) initial spectral reflectance >90% for 25-mrad reading and >87% for 7-mrad reading, and (3) predicted 20 year durability of less than 5% optical performance drop. While the results of the reflective development activities were promising, Alcoa was unable to down-select on a reflective technology that met the target criteria. Given the progress and potential of both silver film and thin film technologies, Alcoa continued reflector surface development activities in Phase II. The Phase I concept development activities began with acquiring baseline CSP system information from both CSP Services and the DOE. This information was used as the basis to develop conceptual designs through ideation sessions. The concepts were evaluated based on estimated cost and high-level structural

Illumination uniformity issue explored via two-stage solar concentrator system based on Fresnel lens and compound flat concentrator

International Nuclear Information System (INIS)

Yeh, Naichia

2016-01-01

This paper illustrates details about the solar radiation distribution on the target of a two-stage solar concentrator that combines the Fresnel lens (FL) and the compound flat concentrator (CFC). The paper starts with a review of some FL development milestones such as the two-stage systems and the comparisons of flat vs. curved lenses in addition to the most noteworthy FL-based solar energy application, concentration photovoltaic (CPV). Through the review of the FL based CPV and two-stage concentrators, this study leads to the development of an algorithm to explore the spectrum distribution insight on the receiver of a two-stage (FL plus CFC) solar concentration system. It established the potential for using a correctly positioned 2nd stage reflector of right dimension to selectively redirect the desired spectrum on the target area so as to enhance the concentration flux intensity and uniformity at the same time. The study also helped to chart out the approximate locations of certain spectrum segments on the FL's target area, which is useful for exploring the spectrum control mechanism via the Fresnel lenses. - Highlights: • Map out the approximate locations of spectrum segments on FL's focal area. • Use the 2nd stage reflector to selectively reflect the desired spectrum on target. • Explore the spectrum distribution insight on FL solar concentrators' target area.

Developing a Reading Concentration Monitoring System by Applying an Artificial Bee Colony Algorithm to E-Books in an Intelligent Classroom

Directory of Open Access Journals (Sweden)

Yueh-Min Huang

2012-10-01

Full Text Available A growing number of educational studies apply sensors to improve student learning in real classroom settings. However, how can sensors be integrated into classrooms to help instructors find out students’ reading concentration rates and thus better increase learning effectiveness? The aim of the current study was to develop a reading concentration monitoring system for use with e-books in an intelligent classroom and to help instructors find out the students’ reading concentration rates. The proposed system uses three types of sensor technologies, namely a webcam, heartbeat sensor, and blood oxygen sensor to detect the learning behaviors of students by capturing various physiological signals. An artificial bee colony (ABC optimization approach is applied to the data gathered from these sensors to help instructors understand their students’ reading concentration rates in a classroom learning environment. The results show that the use of the ABC algorithm in the proposed system can effectively obtain near-optimal solutions. The system has a user-friendly graphical interface, making it easy for instructors to clearly understand the reading status of their students.