WorldWideScience

Sample records for concentrates ore

  1. Predicting the Concentration Characteristics of Itakpe Iron Ore for cut ...

    African Journals Online (AJOL)

    MICHAEL HORSFALL

    ABSTRACT: Concentration characteristics of an ore are very critical to the estimation of cut-off grade of a ... enormous financial cost of laboratory analysis and time required for such .... Arua A.I. (1997) Fundamentals of statistics, Publisher,.

  2. Acid curing and baking of bastnasite ore and concentrate

    International Nuclear Information System (INIS)

    Topkaya, Y.; Akkurt, S.

    1998-01-01

    Full text: In this study, the hydrometallurgical evaluation of a rare earth ore as well as a concentrate obtained from this was done at laboratory. For the mentioned study, a bastnasite type rare earth ore located in Beylikahir in Turkey was used. The total rare earth oxide (REO) content of the deposit was estimated to be 1 million tons with an average concentration of 3.42%REO. The rare earths were contained in bastnasite mineral. The other constituents of the ore were calcium fluoride (52.5%), barite (25.4%), calcite (2.8%) and minor amounts of thorium, iron, manganese, etc. The bastnasite mineral occurred either as cement material between fluoride and barite particles or as intimately associated with these minerals. The rare earth elements were enriched considerably in sub-sieve sizes. After extensive research about the physical concentration of this ore, two different metallurgical routes were followed for the extraction of REE from the ore itself or the preconcentrate obtained by attrition scrubbing and desliming by cyclones. In order to increase the grade of the concentrate, upgrading of the preconcentrate by multigravity was also tried. The two metallurgical routes tested were: Sulphuric acid curing and water leaching; Sulphuric acid baking and subsequent water leaching. The results of the leaching experiments were found to be quite promising. Leach recoveries up to 90% were easily obtainable. In the case of acid baking, hydrofluoric acid recover as a by-product was also possible

  3. Characterization and concentration of manganese ore waste

    International Nuclear Information System (INIS)

    Lima, Rosa Malena Fernandes; Pereira, Eder Esper; Reis, Erica Linhares; Silva, Glaucia Regina da

    2010-01-01

    In this work is presented the tests results of characterization and concentration by gravity and flotation methods carried out with a manganese sample waste. By optical microscopy, SEM/EDS and X-ray diffractometry were identified the Mn minerals spessartite (20%), tephroite (15%), rhodonite (5%), rhodochrosite and carbonates minerals (29%), opaque minerals and others (16%), micaceus minerals (6%) and quartz (4%). It was obtained Mn metallurgical recovery of 58% with Mn concentrate contents varying from 30 to 32.5%. The concentrates SiO_2 contents of flotation were until 1.5% smaller than those contents of gravity method concentrates. (author)

  4. Influence of the Moisture Content on the Flowability of Fine-Grained Iron Ore Concentrate

    OpenAIRE

    C. Lanzerstorfer; M. Hinterberger

    2017-01-01

    The iron content of the ore used is crucial for the productivity and coke consumption rate in blast furnace pig iron production. Therefore, most iron ore deposits are processed in beneficiation plants to increase the iron content and remove impurities. In several comminution stages, the particle size of the ore is reduced to ensure that the iron oxides are physically liberated from the gangue. Subsequently, physical separation processes are applied to concentrate the iron ore. The fine-graine...

  5. Standard practices for sampling uranium-Ore concentrate

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2010-01-01

    1.1 These practices are intended to provide the nuclear industry with procedures for obtaining representative bulk samples from uranium-ore concentrates (UOC) (see Specification C967). 1.2 These practices also provide for obtaining a series of representative secondary samples from the original bulk sample for the determination of moisture and other test purposes, and for the preparation of pulverized analytical samples (see Test Methods C1022). 1.3 These practices consist of a number of alternative procedures for sampling and sample preparation which have been shown to be satisfactory through long experience in the nuclear industry. These procedures are described in the following order. Stage Procedure Section Primary Sampling One-stage falling stream 4 Two-stage falling stream 5 Auger 6 Secondary Sampling Straight-path (reciprocating) 7 Rotating (Vezin) 8, 9 Sample Preparation 10 Concurrent-drying 11-13 Natural moisture 14-16 Calcination 17, 18 Sample Packaging 19 Wax s...

  6. The production and use of citric acid for the removal of potassium from the iron ore concentrate of the Sishen Iron Ore Mine, South Africa

    Directory of Open Access Journals (Sweden)

    Peter J. Williams

    2010-04-01

    Full Text Available The depletion of the richer iron ore worldwide has made it necessary to process lower quality iron ore. Certain substances, such as potassium, contained within the lower quality iron ore, have a detrimental effect on the smelting process during steel manufacturing. Therefore, international steel-making companies charge penalties when purchasing iron ore concentrates containing high concentrations of potassium. To date, lower quality iron ore has been blended with high quality iron ore in an attempt to alleviate the potassium concentrations in the export iron ore; however, the ratio of low quality iron ore to high quality iron ore is increasing, thereby becoming an escalating problem within the economic functioning of the Sishen Iron Ore Mine. It has, therefore, become necessary to develop an economically viable and environmentally friendly process to reduce the high potassium concentrations contained in the iron ore concentrate of the Sishen Iron Ore Mine. In this study, we compared solid substrate and submerged fermentation using Aspergillus niger for the production of citric acid, which is used for the chemical leaching of potassium from the iron ore concentrate. It was found that submerged fermentation proved to be more economical and efficient, producing a maximum citric acid concentration of 102.3 g/L in 96 h of fermentation. ‘Heap leaching’ simulation experiments were found to be uneconomical, due to the required addition of fungal growth medium every 5 days as a result of growth factor depletion within this time; however, this process removed 17.65% of the potassium from the iron ore concentrate. By contrast, chemical leaching of potassium from the iron ore concentrate proved to be most efficient when using a 1 mol citric acid leaching solution at 60 ºC, removing 23.53% of the potassium contained within the iron ore concentrate. Therefore, the most economical and efficient process for the removal of potassium from the iron

  7. Optimization of dissolution process parameters for uranium ore concentrate powders

    Energy Technology Data Exchange (ETDEWEB)

    Misra, M.; Reddy, D.M.; Reddy, A.L.V.; Tiwari, S.K.; Venkataswamy, J.; Setty, D.S.; Sheela, S.; Saibaba, N. [Nuclear Fuel Complex, Hyderabad (India)

    2013-07-01

    Nuclear fuel complex processes Uranium Ore Concentrate (UOC) for producing uranium dioxide powder required for the fabrication of fuel assemblies for Pressurized Heavy Water Reactor (PHWR)s in India. UOC is dissolved in nitric acid and further purified by solvent extraction process for producing nuclear grade UO{sub 2} powder. Dissolution of UOC in nitric acid involves complex nitric oxide based reactions, since it is in the form of Uranium octa oxide (U{sub 3}O{sub 8}) or Uranium Dioxide (UO{sub 2}). The process kinetics of UOC dissolution is largely influenced by parameters like concentration and flow rate of nitric acid, temperature and air flow rate and found to have effect on recovery of nitric oxide as nitric acid. The plant scale dissolution of 2 MT batch in a single reactor is studied and observed excellent recovery of oxides of nitrogen (NO{sub x}) as nitric acid. The dissolution process is automated by PLC based Supervisory Control and Data Acquisition (SCADA) system for accurate control of process parameters and successfully dissolved around 200 Metric Tons of UOC. The paper covers complex chemistry involved in UOC dissolution process and also SCADA system. The solid and liquid reactions were studied along with multiple stoichiometry of nitrous oxide generated. (author)

  8. INAA of Zn and impurity elements in Zn ores and concentrates

    International Nuclear Information System (INIS)

    Op de Beeck, J.; De Norre, L.; Hoste, J.

    1985-01-01

    The present work concerns the analysis of zinc ores and concentrates. In the first place a procedure for the routine determination of fluorine in Zinc sulfide ores has been developed, based on activation with the fast neutrons of the isotope source. In the second place a procedure for the routine determination of Cadmium in Zinc ores has been developed and finally the routine determination of Zinc itself is at present being completed

  9. Radioactive Ores and Concentrates (Packaging and Transport) Act 1980. No 26 of 1980

    International Nuclear Information System (INIS)

    1980-01-01

    This Act, which regulates the packaging, storage and transport of radioactive ores and concentrates lays down a detailed licensing system for such materials and prescribes the duties of the Chief Inspector responsible for implementation of the Act. (NEA) [fr

  10. Dense medium ore concentrates of Bois-Noirs; Minerais des bois noirs, concentres de milieu dense

    Energy Technology Data Exchange (ETDEWEB)

    Le Bris, J; Leduc, M

    1959-01-20

    The chemical treatment of uranium concentrates of Bois-Noirs ore obtained by heavy medium are discussed. The first part deals with sulfuric acid attack on the concentrate, and the second part with the separation of the solution from residues by filtration. A third part deals with this separation by decantation. The fourth part deals with the carbonation of the pickling solutions obtained. (author) [French] Le present rapport est relatif a l'etude du traitement chimique de concentres uraniferes de minerais des Bois-Noirs obtenus par milieu dense. Une premiere partie est consacree a l'attaque sulfurique des concentres, une deuxieme partie a Ia separation de Ia solution d'attaque des residus par decantation. Une quatrieme partie a la carbonatation des solutions d'attaque obtenues. (auteur)

  11. Determination of uranium concentration in an ore sample using laser-induced breakdown spectroscopy

    International Nuclear Information System (INIS)

    Kim, Y.-S.; Han, B.-Y.; Shin, H.S.; Kim, H.D.; Jung, E.C.; Jung, J.H.; Na, S.H.

    2012-01-01

    Laser-induced breakdown spectroscopy (LIBS) has been recognized as a promising technique for analyzing sensitive nuclear materials such as uranium, plutonium, and curium in a high-radiation environment, especially since the implementation of IAEA (International Atomic Energy Agency) safeguards. The uranium spectra of ore samples were quantitatively analyzed prior to analyzing sensitive materials in the nuclear industry. The purpose of this experiment is to extract quantitative information about the uranium in a uranium ore using a standard addition approach. The uranium ore samples containing different concentrations of U were prepared by mixing raw ore powder with natural uranium oxide powders. Calibration sets of 0.2, 0.4, 0.6, 0.8 and 1.0 wt.% uranium concentrations within the uranium ore sample were achieved. A pulsed and Q-switched Nd:YAG laser at a wavelength of 532 nm was used as a light source. An echelle spectrometer that covers a 190–420 nm wavelength range is used to generate a calibration curve and determine the detection limit of uranium in the ore matrix. The neutral atomic-emission peak at a wavelength of 356.659 nm indicated a detection limit of ∼ 158 ppm for uranium, and the uranium concentration was determined in a raw ore sample that has an unknown quantity of uranium. - Highlights: ► The feasibility of LIBS application to monitor uranium element was carried out. ► The detection limit of U in ore was determined by a standard additional approach. ► Quantitative analyses of U concentration in a natural uranium ore were performed.

  12. Magnetic concentration of iron-titanium ore with vanadium concentrate from campo Alegre de Lourdes - Bahia, Brazil

    International Nuclear Information System (INIS)

    Delgado, O.; Silva, F.T. da; Ogasawara, T.; Soares, G.F.

    1988-01-01

    The feasibility studies of magnetic concentration of the Campo Alegre de Lourdes ore were carried out, trying to obtain a maximum recovery of vanadium. As a consequence of the complex nature of the ore, mainly due to the presence of ilmenite as a exolutions in the interior of hematite/martite particles, it was not possible to separate the hematite-ilmenite eficiently, wich would be necessary for obtaining a high grade vanadium concentrate with low titanium content. (author) [pt

  13. 3.6. The kinetics of sulfuric acid decomposition of calcined concentrate of borosilicate ore

    International Nuclear Information System (INIS)

    Mirsaidov, U.M.; Kurbonov, A.S.; Mamatov, E.D.

    2015-01-01

    Present article is devoted to kinetics of sulfuric acid decomposition of calcined concentrate of borosilicate ore. The experimental data of kinetics of extraction of boron oxide from danburite at sulfuric acid decomposition were obtained at 20-90 deg C temperature range and process duration 15-90 minutes. The flowsheet of obtaining of boric acid from borosilicate ores of Ak-Arkhar Deposit by sulfuric acid method was proposed.

  14. Ore-concentrating structures with telescoped uranium mineralization

    International Nuclear Information System (INIS)

    Shchetochkin, V.N.; Dmitriyev, V.I.; Tkachenko, I.I.

    1986-01-01

    Deep faults are the main controlling elements in uranium ore fields, although the immediate geologic environments may be quite varied. Within the fault zones, the uranium fields are usually associated with areas where major transverse and diagonal faults intersect or link, and with points of splitting or change in strike in disjunctive zones. Another distinctive feature of the mineralized structure is their long history, with a combination of tectonic elements differing in age and type, usually associated with retrograde dislocation metamorphism. The specific features of these structures control the uranium mineralization, which is usually localized in foci with telescoped tectonic, magmatic, hydrothermal, metasomatic, and sometimes exogenous processes. The unnamed area (in the Ukraine?) furnishes a good example of how successive stages of a complex geologic history affect the occurrence of such a highly mobile element as uranium. 12 references, 4 figures

  15. Multistage dilute acid leaching of a medium grade iron ore to super-concentrate

    Directory of Open Access Journals (Sweden)

    Adeleke A.A.

    2014-01-01

    Full Text Available The phosphorous laden Koton Karfe iron ore is a medium grade iron ore deposit in Nigeria that can be upgraded as a super-concentrate for use at the Aladja Steel Midrex plant. The 75 μm size sample fraction of the ore was preconcentrated with shaking table and leached in the oven at atmospheric pressure with dilute hydrochloric acid in single and multistage leaching sequences of H2O-HCl-H2O and HCl-H2O-H2O. The as-received, as-tabled and asleached samples were then subjected to X-ray fluorescence and microscopic analyses. The results obtained showed that the H2O-HCl-H2O route produced a higher grade concentrate that assayed 68.54% Fe indicating about 58% upgrade in iron content; while the phosphorus and sulphur contents were reduced by about 77 and 99.6% respectively. In addition, the silicon, manganese, and titanium contents were drastically reduced, while potassium was completely eliminated. The upgrade of iron content in the ore to 68.54% and the drastic reduction in phosphorous and sulphur contents has thus rendered the Koton Karfe iron ore suitable for use as a super concentrate for the Aladja steel plant direct reduction iron making process.

  16. New route for uranium concentrate production from Caetite ore, Bahia State, Brazil; dynamic leaching - direct precipitation

    Energy Technology Data Exchange (ETDEWEB)

    Morais, Carlos A. [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)]. E-mail: cmorais@cdtn.br; Gomiero, Luiz A.; Scassiotti Filho, Walter [Industrias Nucleares do Brasil S.A. (INB), Caetite, BA (Brazil)]. E-mails: gomiero@inb.gov.br; scassiotti@inb.gov.br

    2007-07-01

    The common uranium concentrate production consists of ore leaching, uranium purification/concentration by solvent extraction and uranium precipitation as ammonium diuranate steps. In the present work, a new route of uranium concentrate production from Caetite, BA-Brazil ore was investigated. The following steps were investigated: dynamic leaching of the ground ore with sulfuric acid; sulfuric liquor pre-neutralization until pH 3.7; uranium peroxide precipitation. The study was carried out in bath and continuous circuits. In the dynamic leaching of ground ore in agitated tanks the uranium content in the leached ore may be as low as 100 {mu}g/g U{sub 3}O{sub 8}, depending on grinding size. In the pre-neutralization step, the iron content in the liquor is decreased in 99 wt.%, dropping from 3.62 g/L to 0.030 g/L. The sulfate content in the liquor reduces from 46 g/L to 22 g/L. A calcinated final product assaying 99.7 wt.% U{sub 3}O{sub 8} was obtained. The full process recovery was over 94%. (author)

  17. Morphological Comparison of U3O8 Ore Concentrates from Canada Key Lake and Namibia Sources

    Energy Technology Data Exchange (ETDEWEB)

    Schwartz, Daniel S. [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Tandon, Lav [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Martinez, Patrick Thomas [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

    2016-03-11

    Uranium ore concentrates from two different sources were examined using scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). The ore powders are referred to as Namibia (id. no. 90036, LIMS id. no. 18775) and Canada Key Lake (id. no. 90019, LIMS id. no. 18774). Earlier work identified the ores as the U₃O₈ phase of uranium oxide using x-ray diffraction. Both sets of powders were in the form of dark brown to black powder fines. However, the Canada Key Lake concentrates contained larger chunks of material on the millimeter scale that were easily visible to the unaided eye. The powders were mounted for SEM examination by hand dispersing a small amount onto conductive sticky tape. Two types of applicators were used and compared: a fine-tipped spatula and a foam-tipped applicator. The sticky tape was on a standard SEM “tee” mount, which was tapped to remove loose contamination before being inserted into the SEM.

  18. Concentration of rare earths ore from Pocos de Caldas - MG, Brazil

    International Nuclear Information System (INIS)

    Sampaio, J.A.; Lins, F.F.; Porphirio, N.H.

    1990-01-01

    The objective of this research was to concentrate, mainly by flotation, a rare-earth ore body. The valuable mineral is bastnaesite which occurs intimately associated with iron oxides and other gangue minerals, making difficult to get a concentrate of commercial grade. The use of oleic acid at a pulp temperature of -80 sup(0)C gave a concentrate of 23% rare-earth oxides at 72% overall recovery. The magnetic separation could enhance the grade of the flotation feed. (author)

  19. Removing ferric ions from concentrated acid leaching solution of an uranium ore by jarosite

    International Nuclear Information System (INIS)

    Song Huanbi; Hu Yezang

    1997-01-01

    The author expounds the fundamental rules of removing ferric ions by jarosite and presents results of removing ferric ions from concentrated acid curing-trickle leaching solution of an uranium ore. It turns out that the method can be applied to uranium hydrometallurgical process effectively

  20. Continuous tests of Phosphoric Acid - dihydrate process - from phosphatic concentrate of Itataia-CE ore

    International Nuclear Information System (INIS)

    Santos Benedetto, J. dos.

    1984-01-01

    A consolidation of principal studies and continuous tests done with phosphatic concentrated of Itataia ore intending phosphoric acid production by humid-route dihydrate way process is presented. The production of phosphoric acid is applied in uranium extraction process by solvents. (author) [pt

  1. Technical Report on the Behavior of Trace Elements, Stable Isotopes, and Radiogenic Isotopes During the Processing of Uranium Ore to Uranium Ore Concentrate

    Energy Technology Data Exchange (ETDEWEB)

    Marks, N. E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Borg, L. E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Eppich, G. R. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Gaffney, A. M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Genneti, V. G. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Hutcheon, I. D. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Kristo, M. J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Lindvall, R. E. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Ramon, C. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Robel, M. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Roberts, S. K. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Schorzman, K. C. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Sharp, M. A. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Singleton, M. J. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States); Williams, R. W. [Lawrence Livermore National Lab. (LLNL), Livermore, CA (United States)

    2015-07-09

    The goals of this SP-1 effort were to understand how isotopic and elemental signatures behave during mining, milling, and concentration and to identify analytes that might preserve geologic signatures of the protolith ores. The impurities that are preserved through the concentration process could provide useful forensic signatures and perhaps prove diagnostic of sample origin.

  2. Link between ore bodies and biosphere concentrations of uranium

    International Nuclear Information System (INIS)

    Gordon, S.

    1992-01-01

    A literature review of uranium exploration studies was carried out to determine the size and concentration of uranium anomalies in the biosphere. Fourteen sites were studied and uranium data were obtained for rocks, water-borne sediments, surface waters, groundwaters, soils and plants. Detailed descriptions of the study areas and of their uranium anomalies are provided. No statistical analyses of the data of anomaly sizes was undertaken because of the variation in the scale of the studies and in the threshold values used and the small number of samples for each medium. The threshold values and the size of the anomaly were found to be dependent on the scale of the study and of the sampling density. Sediments and surface waters were found to have the largest uranium dispersion. Although there was a wide range in the anomaly sizes it was possible to assign typical values for each medium. Based on a typical source of 1 km 2 in the rock it was found that anomalies of similar size as the source are expected in soils and plants, anomalies twice as large are typical for sediments and surface waters and anomalies of smaller areas than the source are possible for groundwater. Some limitations to providing typical groundwater anomaly sizes are outlined. Typical maximum concentrations for the sites studied were greater than 1300 ppm for rock, 10 to 110 ppm for sediment, and 5 ppb for surface waters. No typical values were observed for groundwater, soils and plants. Susceptibility of the host rock to leaching and the presence of discharge zones were assessed for their role in biosphere anomalies

  3. Management of wastes from the refining and conversion of uranium ore concentrate to uranium hexafluoride

    International Nuclear Information System (INIS)

    1981-01-01

    This report is the outcome of an IAEA Advisory Group Meeting on ''Waste Management Aspects in Relation to the Refining of Uranium Ore Concentrates and their Conversion to Uranium Hexafluoride'', which was held in Vienna from 17 to 21 December 1979. The report summarizes the main topics discussed at the meeting and gives an overview of uranium refining processes, being used in nuclear industry. The meeting was organized by the International Atomic Energy Agency, Radioactive Waste Management Section

  4. Characterization and classification of uranium ore concentrates (yellow cakes) using infrared spectrometry

    Energy Technology Data Exchange (ETDEWEB)

    Varga, Z.; Oeztuerk, B.; Mayer, K.; Wallenius, M.; Apostolidis, C. [Joint Research Centre, Karlsruhe (Germany). Inst. for Transuranium Elements; Meppen, M. [Carl Friedrich von Weizsaecker-Zentrum fuer Naturwissenschaft und Friedensforschung, Hamburg (Germany)

    2011-07-01

    In this work the applicability of Fourier-transform infrared spectrometry (FTIR) for nuclear forensic studies of uranium ore concentrates (UOC) are investigated. The technique was used for the identification of the type of uranium compound and various process-related impurities, which can give information on the production method of the material. The measured spectra were evaluated also by statistical means, using the soft independent modelling of class analogy (SIMCA) technique to reveal less apparent similarities between the measured UOC samples.

  5. Origin assessment of uranium ore concentrates based on their rare-earth elemental impurity pattern

    Energy Technology Data Exchange (ETDEWEB)

    Varga, Z.; Wallenius, M.; Mayer, K. [Commission of the European Communities, Karlsruhe (Germany). European Inst. for Transuranium Elements

    2010-07-01

    The rare-earth element pattern was used as an additional tool for the identification and origin assessment of uranium ore concentrates (yellow cakes) for nuclear forensic purposes. By this means, the source of an unknown material can be straightforwardly verified by comparing the pattern with that of a known or declared sample. In contrast to other indicators used for nuclear forensic studies, the provenance of the material can also be assessed in several cases even if no comparison sample is available due to the characteristic pattern. The milling process was found not to change the pattern and no significant elemental fractionation occurs between the rare-earth elements, thus the pattern in the yellow cakes corresponds to that found in the uranium ore. (orig.)

  6. Recovery of uranium mineral from Liaoning Fengcheng ludwigite ore by gravity concentration

    International Nuclear Information System (INIS)

    Zhang Tao; Liang Haijun; Xue Xiangxin

    2009-01-01

    A laboratory research was carried out to recover uranium mineral from Liaoning Fengcheng ludwigite ore. Gravity concentration methods including hydroclone, spiral chute and shaking table were applied in this study. The results show that a concentrate with uranium grade of 0.216% and recovery of 44.24% could be produced from the feed of uranium content 0.006 3%. This research is helpful to comprehensive utilization of the mineral resources. Increasing further uranium mineral liberation degree is the key to improve separation effects. (authors)

  7. The recovery of a concentrate of tin and tungsten from ore mined at Van Roois Vley

    International Nuclear Information System (INIS)

    Guest, R.N.

    1985-01-01

    Concentration tests using gravity separation, flotation, and magnetic separation showed that it is possible for the high-grade ore mined at Van Roois Vley to be upgraded to a concentrate containing 61 per cent Sn-Wo 3 at a recovery of about 80 per cent, and for the low-grade ore to be upgraded to 53 per cent Sn-WO 3 at the same recovery. However, it is suggested that, under normal mining conditions and with large-scale mining equipment, less fines would be produced and this should lead to an increase in grade and recovery. Mineralogical examinations showed that intermediate fractions produced by tabling contained very few locked particles, and that the grade of the final concentrate on a full-scale plant would probably be higher than that obtained with laboratory equipment. Molybdenite could be a valuable byproduct, but flotation tests of gravity concentrates for selective recovery of the mineral gave variable results. Flotation tests for the removal of fluorspar from the final concentrate were unsuccessful

  8. Prediction of ore fluid metal concentrations from solid solution concentrations in ore-stage calcite: Application to the Illinois-Kentucky and Central Tennessee Mississippi Valley-type districts

    Science.gov (United States)

    Smith-Schmitz, Sarah E.; Appold, Martin S.

    2018-03-01

    Knowledge of the concentrations of Zn and Pb in Mississippi Valley-type (MVT) ore fluids is fundamental to understanding MVT deposit origin. Most previous attempts to quantify the concentrations of Zn and Pb in MVT ore fluids have focused on the analysis of fluid inclusions. However, these attempts have yielded ambiguous results due to possible contamination from secondary fluid inclusions, interferences from Zn and Pb in the host mineral matrix, and uncertainties about whether the measured Zn and Pb signals represent aqueous solute or accidental solid inclusions entrained within the fluid inclusions. The purpose of the present study, therefore, was to try to determine Zn and Pb concentrations in MVT ore fluids using an alternate method that avoids these ambiguities by calculating Zn and Pb concentrations in MVT ore fluids theoretically based on their solid solution concentrations in calcite. This method was applied to the Illinois-Kentucky and Central Tennessee districts, which both contain ore-stage calcite. Experimental partition coefficient (D) values from Rimstidt et al. (1998) and Tsusue and Holland (1966), and theoretical thermodynamic distribution coefficient (KD) values were employed in the present study. Ore fluid concentrations of Zn were likely most accurately predicted by Rimstidt et al. (1998) D values, based on their success in predicting known fluid inclusion concentrations of Mg and Mn, and likely also most accurately predicted ore fluid concentrations of Fe. All four of these elements have a divalent ionic radius smaller than that of Ca2+ and form carbonate minerals with the calcite structure. For both the Illinois-Kentucky and the Central Tennessee district, predicted ore fluid Zn and Fe concentrations were on the order of up to 10's of ppm. Ore fluid concentrations of Pb could only be predicted using Rimstidt et al. (1998) D values. However, these concentrations are unlikely to be reliable, as predicted ore fluid concentrations of Sr and Ba

  9. Application of neutron activation analysis to control P2O5 content in ore and ore concentrates of ''Apatit'' works

    International Nuclear Information System (INIS)

    Belyakov, M.A.; Terent'eV, Eh.P.; Frolov, V.A.

    1982-01-01

    A technique for a neutron activation rapid analysis of fluorine is described. A mean-square error of the analysis makes up 0,g3 per cent F. The investigation has been carried out and a close correlation has been established for the Hibine massif exploited apatite deposits on the basis of the neutron activation analysis of fluorine and chemical analysis of P 2 O 5 . Possibilities are shown of using the neutron activation analysis of P 2 O 5 in ores and certain ore con-- centrates of ''Apatit'' works from the radioactivity induced in fluorine. A mean-square error of the analysis makes up 0,35 per cent P 2 O 5

  10. Simple, cost effective method for determination of phosphorus in uranium ore concentrate

    International Nuclear Information System (INIS)

    Misra, U.B.; Ramamurty, Vasantha; Dutta, M.; Balaji Rao, Y.; Subba Rao, Y.

    2015-01-01

    In this paper determination of phosphate as phosphorus in uranium ore concentrate has been described. The method used is spectrophotometric determination of phosphorus as phospho-molybdenum blue complex. As uranyl ion do not absorb in 600-900 nm range of visible region in the present medium, the phosphomolybdenum blue complex formation which is having maximum absorbance at 825 nm is exploited for determination of phosphorus. The molar absorptivity coefficient with and without the presence of uranium matrix are 2.6048 x 10 4 and 2.6730 x 10 4 lmol -1 cm -1 . The effect of matrix is not evident from the experiment carried out. (author)

  11. An Overview of Process Monitoring Related to the Production of Uranium Ore Concentrate

    Energy Technology Data Exchange (ETDEWEB)

    McGinnis, Brent [Innovative Solutions Unlimited, LLC

    2014-04-01

    Uranium ore concentrate (UOC) in various chemical forms, is a high-value commodity in the commercial nuclear market, is a potential target for illicit acquisition, by both State and non-State actors. With the global expansion of uranium production capacity, control of UOC is emerging as a potentially weak link in the nuclear supply chain. Its protection, control and management thus pose a key challenge for the international community, including States, regulatory authorities and industry. This report evaluates current process monitoring practice and makes recommendations for utilization of existing or new techniques for managing the inventory and tracking this material.

  12. A laboratory study to evaluate the possibility of sulphur and phosphorous removal from iron ore concentrate by leaching

    Directory of Open Access Journals (Sweden)

    Pour Hassan Rezvani

    2016-01-01

    Full Text Available Iron ore concentrates with high grade sulfur cause several problems in the steel making process, and hence affect the concentrate price. Environmental issues such as sulfur dioxide emission during the concentrate pelletizing process and effect on the steel quality are other issues. The current study was focused on removal of sulfur from the iron ore concentrate by using the chemical leaching technique. The magnetite iron ore concentrate was chosen for this purpose. The results obtained showed that more than 90% of the total sulfur content was removed from the iron ore concentrate by chemical leaching. Effects of several parameters such as temperature, particle size and use of organic solvent on sulfur removal were investigated by a series of experiments. After optimizing the experimental conditions, it was demonstrated that with addition of sulfur, phosphorus, another important impurity was also removed from the iron ore concentrate. In addition, one of the major advantages of our proposed method was transformation of mineral pyrites to useful by-products such as elemental sulfur.

  13. Measurements of CaF2 concentration in fluorite ore using thermoluminescence techniques

    International Nuclear Information System (INIS)

    Lembo, L.; Maestri, G.; Pimpinella, M.; Benzi, V.; Muntoni, C.

    1990-01-01

    Fluorite powder is produced by means of a flotation process on crude ore extracted by the mines. A full automation of the flotation plant would reduce the operating cost and improve the quality and recovery of fluorite production. However, taking into account that the efficiency of a flotation cycle is directly dependent on the CaF 2 content in the concentrate and tail products, this automation requires a quasi-real-time quantitative analysis of CaF 2 concentration in the floated pulp. The feasibility was studied of using a thermoluminescence technique as an on-line analysis method to measure the CaF 2 concentration during the flotation cycle. A first set of experimental conditions to determine CaF 2 content in acid-grade fluorspar has been already developed and the preliminary results so far obtained are presented. (author)

  14. Atomic-absorption determination of tantalum and niobium in ore concentrates

    International Nuclear Information System (INIS)

    Elinson, S.V.; Korovin, Yu.I.; Kuchumov, V.A.

    1975-01-01

    A flame atom-absorption method was developed for determining tantalum and niobium at their level greater than 5% in Ta-Nb ore concentrates. Flame was produced by a nitrous oxide-acetylene mixture. The optimal composition of a buffer (3 mg/ml) of iron was determined by the method of factorial planning of the experiment and steep ascention by gradient. The optimizing parameter in factorial planning was obtained from the difference of optical densities of Ta and Nb, by taking the average value for two solutions which had dissimilar total composition and which imitated the real composition of the ore concentrates, i.e., the value of (ΔD/Dsub(av))sub(Ta) or (ΔD/Dsub(av))sub(Nb). The optimization of analytical conditions corresponded to the condition (ΔD/Dsub(av))→ 0, which indicated that the chosen optimizing parameter also facilitated the attainment of maximum D values. The variation coefficient in the determination of Ta and Nb was respectively 0.8 and 1.4%. There was a good agreement between the results obtained in Ta analysis by the atom-absorption and the extraction-gravimetric methods, and in Nb analysis by the atom-absorption, differential spectrophotometric and x-ray fluorescence methods

  15. A discussion about maximum uranium concentration in digestion solution of U3O8 type uranium ore concentrate

    International Nuclear Information System (INIS)

    Xia Dechang; Liu Chao

    2012-01-01

    On the basis of discussing the influence of single factor on maximum uranium concentration in digestion solution,the influence degree of some factors such as U content, H 2 O content, mass ratio of P and U was compared and analyzed. The results indicate that the relationship between U content and maximum uranium concentration in digestion solution was direct ratio, while the U content increases by 1%, the maximum uranium concentration in digestion solution increases by 4.8%-5.7%. The relationship between H 2 O content and maximum uranium concentration in digestion solution was inverse ratio, the maximum uranium concentration in digestion solution decreases by 46.1-55.2 g/L while H 2 O content increases by 1%. The relationship between mass ratio of P and U and maximum uranium concentration in digestion solution was inverse ratio, the maximum uranium concentration in digestion solution decreases by 116.0-181.0 g/L while the mass ratio of P and U increase 0.1%. When U content equals 62.5% and the influence of mass ratio of P and U is no considered, the maximum uranium concentration in digestion solution equals 1 578 g/L; while mass ratio of P and U equals 0.35%, the maximum uranium concentration decreases to 716 g/L, the decreased rate is 54.6%, so the mass ratio of P and U in U 3 O 8 type uranium ore concentrate is the main controlling factor. (authors)

  16. Influence of a High-Pressure Comminution Technology on Concentrate Yields in Copper Ore Flotation Processes

    Directory of Open Access Journals (Sweden)

    Saramak D.

    2014-10-01

    Full Text Available The article concerns the issues of flotation process effectiveness in relationship to the operating conditions of a high-pressure comminution process course. Experimental programme covering a flotation laboratory batch tests was a verification technique of a high-pressure crushing operations course. The most favorable values of flotation concentrate weight recoveries were obtained for the pressing force 6 kN and 4% of the feed moisture. It was also determined the model of the concentrate weight recovery as a function of pressing force in the press and feed moisture content. This model was the basis for the optimization of effects of copper ore flotation processes preceded in high-pressure crushing operation in roller presses.

  17. Factors Affecting Ballability of Mixture Iron Ore Concentrates and Iron Oxide Bearing Wastes in Metallurgical Processing

    Directory of Open Access Journals (Sweden)

    Mfon Udo

    2018-05-01

    Full Text Available Iron oxide bearing wastes (IROBEWAS are produced at every segment of processing stage of sinter, molten iron and steel production. They are hard to handle and in many cases are stockpiled only to be a source of environmental pollution but can be balled into pellets. Pellet of good ballability values are transportable and recyclable as they can withstand stress they will encounter without disintegrating back to dust. But ballability is affected by some factors like the grain sizes of the materials, the moisture and binder contents of the ball mix, wettability of the balled materials and the processing perimeters of the granulator. The objective of this research work is to investigate the factors affecting ballability of mixture of iron ore concentrates and iron oxide bearing wastes (IROBEWAS in metallurgical processing. The parameters under consideration were grain size of materials, the moisture contents, the speed of balling disc, IROBEWAS and Bentonite (Binder contents of the balled mix. This was carried out by balling different volume fractions of mix containing iron oxide concentrate and IROBEWAS using a balling disc and testing the resulting balls for green compressive strength using universal testing machine. It was found that the ballability of the mixture of iron ore concentrate and IROBEWAS increases as grain sizes of the materials reduce but increases as the moisture contents and IROBEWAS content increase up to an optimum value of moisture content in the mix before it starts to reduce. The ballability also increases as the speed of the granulator (Balling disc increases within the limit of this work. It was also observed that there was an increase in ballability with slight increase in bentonite content in the mix.

  18. Enhancement of Cu, Ni and Mo recoveries in the bulk concentrate of Jaduguda uranium bearing ore

    International Nuclear Information System (INIS)

    Rao, G.V.; Besra, L.D.

    1998-01-01

    The uranium ore treatment plant at Jaduguda, India, recovers copper, nickel and molybdenum as byproducts before the bulk flotation tailings are subjected to leaching to recover uranium values. The recoveries of these sulfide metals in this 900 TPD plant are reported to be around 60 % Cu, 25% Ni and 55% Mo in the bulk concentrate. In this article, flotation studies carried out, at the instance of M/S UCIL, with various reagents and their combination to improve the over all recoveries are presented. It was observed that material coarser than 100 microns, from the flotation feed, could not be floated even in presence of excessive reagent unless it is ground further. It was established that around 95% Cu, 75% Ni and 74% Mo values could be recovered by using either amyl xanthate or mixture of amyl xanthate and Aero Promoter 194 in place of cresylic acid that is being currently used as collector in the plant. (author)

  19. Influence of radon-daughter exposure rate and uranium ore dust concentration on occurrence of lung tumors

    International Nuclear Information System (INIS)

    Cross, F.T.; Palmer, R.F.; Busch, R.H.

    1980-01-01

    Groups of male SPF Wistar rats were exposed concurrently to several levels of radon daughters and uranium ore dust to study the effect of these variables on pulmonary disease states. Clinical pathology data at 1 yr postexposure indicate no significant differences among exposed animals when compared with controls. Preliminary histopathologic data suggest a trend toward increasing lung tumor risk as the exposure rate is decreased (constant total dose), but the differences are not statistically significant at the 0.05 level. A similar trend occurs with decrease in ore dust concentration (except for the 2560-WLM exposure group), but these differences are also not significant at the 0.05 level. The tumor risk is significantly (0.05 level) increased as the exposure level increases from approximately 320 and 640 WLM to 2560 WLM at the high ore dust concentration

  20. Concentration and Separation of Scandium from Ni Laterite Ore Processing Streams

    Directory of Open Access Journals (Sweden)

    Şerif Kaya

    2017-12-01

    Full Text Available The presence of a considerable amount of scandium in lateritic nickel-cobalt ores necessitates the investigation of possible processing alternatives to recover scandium as a byproduct during nickel and cobalt production. Therefore, in this study, rather than interfering with the main nickel-cobalt production circuit, the precipitation-separation behavior of scandium during a pH-controlled precipitation process from a synthetically prepared solution was investigated to adopt the Sc recovery circuit into an already existing hydrometallurgical nickel-cobalt hydroxide processing plant. The composition of the synthetic solution was determined according to the hydrometallurgical nickel laterite ore processing streams obtained from a HPAL (high-pressure sulphuric acid leaching process. In order to selectively precipitate and concentrate scandium with minimum nickel and cobalt co-precipitation, the pH of the solution was adjusted by CaCO3, MgO, Na2CO3, and NaOH. It was found that precipitation with MgO or Na2CO3 is more advantageous to obtain a precipitate containing higher amounts of scandium with minimum mass when compared to the CaCO3 route, which makes further processing more viable. As a result of this study, it is proposed that by a simple pH-controlled precipitation process, scandium can be separated from the nickel and cobalt containing process solutions as a byproduct without affecting the conventional nickel-cobalt hydroxide production. By further processing this scandium-enriched residue by means of leaching, SX (solvent extraction, and precipitation, an intermediate (NH42NaScF6 product can be obtained.

  1. Radioactive Ores and Concentrates (Packaging and Transport) Regulations 1980 (Northern Territory) No. 30 of 21 July 1980

    International Nuclear Information System (INIS)

    1980-01-01

    These Regulations were issued pursuant to the provisions of the 1980 Radioactive Ores and Concentrates (Packaging and Transport) Act. The primary purpose of the Regulations is to lay down specific record-keeping practices for persons licensed to transport and store radioactive material. (NEA) [fr

  2. Measurement of Natural Radioactive Nuclide Concentrations and the Dose Estimation of Workers Originated from Radon in Manganese Ore Mine

    International Nuclear Information System (INIS)

    Mansour, N.A.; Hassan, N.M.; Blasy, M.R.

    2013-01-01

    Manganese ore is widely used in many industries. Such as ore contain natural radioactive nuclides at various concentrations. If this ore contain high concentrations of natural radioactive nuclides, workers handling them might be exposed to significant levels of radiation. Therefore it is important to determine the radioactive nuclides in this ore. Also the regulation of radon concentration at workplaces has gained an accentuated importance in all countries. Nevertheless, at this time there is no globally accepted workplace protocol that sets out safe radon concentration values. In this study the radon concentration measured by using an Alpha Guard radon monitor, the equilibrium factor which was greater than the value given in literature, effective radiation dose, which are necessary for the exact estimation of the radiation dose originating from radon. The regulation of radon concentration at workplaces has gained an accentuated importance in all countries. Approach: The natural radionuclides ( 238 U, 232 Th and 40 K) contents of manganese ore samples collected from Umm Bogma, southwest Sinai and from the mountain access Hamid South Eastern Desert, Egypt have been determined by low background spectroscopy using hyper-pure germanium (HPGe) detector. Results: The mean activities due to the three radionuclides ( 238 U, 232 Th and 40 K) were found to be 1500±65, 490±65 and 364±45 Bqkg -1 , respectively. The absorbed dose rate due to the natural radioactivity in samples under investigation ranged from 1522±45 → 1796±43 nGyh -1 . The radium equivalent activity varied from 3807±114→ 4446±133 Bqkg -1 .The representative external hazard index values for the corresponding samples are also estimated. Conclusion: The results of this assessment obtained by the gamma-ray spectroscopic analysis, have indicated that the levels of natural radioactivity were lower than the international recommended limits.

  3. Feasibility Studies for Production of Pellet Grade Concentrate from Sub Grade Iron Ore Using Multi Gravity Separator

    Science.gov (United States)

    Rao, Gottumukkala Venkateswara; Markandeya, R.; Kumar, Rajan

    2018-04-01

    An attempt has been made to utilise Sub Grade Iron Ore by producing pellet grade concentrate from Deposit 5, Bacheli Complex, Bailadila, Chhattisgarh, India. The `as received' Run of Mine (ROM) sample assayed 40.80% Fe, 40.90% SiO2. Mineralogical studies indicated that the main ore mineral is Hematite and lone gangue mineral is Quartz. Mineral liberation studies indicated that, the ore mineral Hematite and gangue mineral Quartz are getting liberated below 100 microns. The stage crushed and ground sample was subjected to concentration by using a Multi Gravity Separator (MGS). Rougher Multi Gravity Separation (MGS) experimental results were optimised to recover highest possible iron values. A concentrate of 55.80% Fe with a yield of 61.73% by weight with a recovery of 84.42% Iron values was obtained in rougher MGS concentrate. Further experiments were carried out with rougher MGS concentrate to produce a concentrate suitable for commercial grade pellet concentrate. It was proved that a concentrate assaying 66.67% Fe, 3.12% SiO2 with an yield of 45.08% by weight and with a recovery of 73.67% iron values in the concentrate.

  4. Investigation of spectral interference effects on determination of uranium concentration in phosphate ore by inductively coupled plasma optical emission spectroscopy

    Energy Technology Data Exchange (ETDEWEB)

    Bachari, Ayoob H.; Jalali, Fatemeh; Alahyarizadeh, Ghasem [Tehran Univ. (Iran, Islamic Republic of). Engineering Dept.

    2017-04-01

    Effects of spectral interferences on determination of the uranium concentration in phosphate ore were investigated by inductively coupled plasma optical emission spectroscopy (ICP-OES). Eleven high intensity emission lines including four lines recommended by ICP-OES apparatus were chosen to determine the uranium concentration. The ore samples were collected from phosphate acid producing industry in the south of Iran. Three different acid combinations [(HNO{sub 3}:HCl:HF-2:6:2), (H{sub 3}PO{sub 4}:H{sub 2}SO{sub 4}:HF-3:3:3), (HNO{sub 3}:H{sub 2}O{sub 2}:HF-4:2:2)] used in microwave digestion method to explore the spectral interference effects in different solvent environments. The results showed that the trusty uranium concentration, obtained in the 367.007 nm, 386.592 nm, 389.036 nm and 409.014 nm by second acid digestion method which were 0.665 ppm, 0.972 ppm, 0.670 ppm and 0.801 ppm, respectively. Although the line of 409.014 nm was reported as the best line for determining of the uranium concentration in several literatures, the results showed that this line has a significant spectral interference with vanadium in some ores which should be considered in determining of the uranium concentration. Spectral interference effects of some elements which have high concentrations in the phosphate ore including Ca, Fe, Mg, Pb, V, Mn, and Ti on the line intensities were also investigated. Results indicated that the chosen elements affect emission intensities of all of 11 lines. They also indicated that the line of 409.014 nm provides a trusty precision in the determination of the uranium concentration in the ore sample with low vanadium concentration (at least, U/V ratio of 1:5). Results show that the line of 409.014 nm provides acceptable precision with some corrections in comparison with other selected lines. For instance in high concentrations of other elements including Fe and Ti in the ore samples, strong influences on the line intensities of the 367.007 nm (by Fe

  5. Nuclear forensic analysis of an unknown uranium ore concentrate sample seized in a criminal investigation in Australia

    International Nuclear Information System (INIS)

    Keegan, Elizabeth; Kristo, Michael J.; Colella, Michael; Robel, Martin; Williams, Ross; Lindvall, Rachel; Eppich, Gary; Roberts, Sarah; Borg, Lars; Gaffney, Amy; Plaue, Jonathan; Wong, Henri; Davis, Joel; Loi, Elaine; Reinhard, Mark; Hutcheon, Ian

    2014-01-01

    In early 2009, a state policing agency raided a clandestine drug laboratory in a suburb of a major city in Australia. While searching the laboratory, they discovered a small glass jar labelled 'Gamma Source' and containing a green powder. The powder was radioactive. This paper documents the detailed nuclear forensic analysis undertaken to characterize and identify the material and determine its provenance. Isotopic and impurity content, phase composition, microstructure and other characteristics were measured on the seized sample, and the results were compared with similar material obtained from the suspected source (ore and ore concentrate material). While an extensive range of parameters were measured, the key 'nuclear forensic signatures' used to identify the material were the U isotopic composition, Pb and Sr isotope ratios, and the rare earth element pattern. These measurements, in combination with statistical analysis of the elemental and isotopic content of the material against a database of uranium ore concentrates sourced from mines located worldwide, led to the conclusion that the seized material (a uranium ore concentrate of natural isotopic abundance) most likely originated from Mary Kathleen, a former Australian uranium mine

  6. Optimization of copper ore concentration processing by means of radioactive tracers

    International Nuclear Information System (INIS)

    Petryka, L.; Przewlocki, K.

    1989-01-01

    Flotation of polymetallic ores in the Polish Lower Silesian Basin was taken as an example for the optimization of copper ore processing using radioactive tracers. An original stochastic mathematical model (stream model) was proposed to minimize copper losses in tailing. A detailed procedure of measurement is presented as well as the experimental data and their interpretation. On the basis of this research copper losses in tailing can be reduced to one third. (author)

  7. Replacement of lumpy chrome ore by agglomerated ore concentrates and lowering of specific power consumption and improvement of Cr-yield by means of improved slag composition in the production of H.C. Ferrochrome

    International Nuclear Information System (INIS)

    Retelsdorf, H.J.; Fichte, R.; Breuer, F.; Zimmermann, H.

    1982-06-01

    Work on this project is finished, but further work on the use of Cr-ore briquettes seems necessary. It was the aim of the project to develop improved slag compositions for the FeCr 4-6% C-process resulting in higher Cr-yield and lower specific power consumption. Furthermore, replacement of lumpy ore in the charge by agglomerated Cr-ore-fines or concentrates in the form of pellets and briquettes was to be tested. Experimentals were performed in a 70 kW and a 300 kW arc furnace. Two different slag compositions were tested. The high-MgO slag type proved suitable. The specific power consumption and the Cr-yield depend to a large extent on the type of Cr-ore and on the agglomeration process. Cr-ore pellets can be used up to 65% in the ore charge but briquettes can be used only up to 25% to replace lumpy ores without causing higher Cr-losses in the slag. (orig.) [de

  8. Critical evaluation of safety and radiological protection requirements adopted for the transport of uranium and thorium ores and concentrates

    International Nuclear Information System (INIS)

    Mezrahi, Arnaldo; Crispim, Verginia R.

    2009-01-01

    This work evaluates in a critical way the safety and radiological protection recommendations established by the International Atomic Energy Agency - IAEA and adopted national and internationally, for the transport of uranium and thorium ores and concentrates, known according the transport regulations, as being of the Low Specific Activity Material Type-I, LSA-I, basing on more realistic scenarios than the presently existent, aiming at the determination of maximum exposure levels of radiation as well as the maximal contents of those materials in packages and conveyance. A general overview taking into account the scenarios foreseen by the regulations of the IAEA pointed out for a need of a better justification of the requirements edited by the Agency or should be used to support a request of revision of those regulations, national and internationally adopted, in the pertinent aspects to the transport of uranium and thorium ores and concentrates. (author)

  9. Evaluation the effect of uranium ore concentrations on the cyc2 gene expression in the mutated Acidithiobacillus sp. FJ2

    Directory of Open Access Journals (Sweden)

    Faezeh Fatemi

    2018-06-01

    Full Text Available Introduction: The uranium bioleaching process is performed using Acidithiobacillus ferrooxidans. This bacterium is capable of iron oxidation by an electron transport chain. One of the most important components of this chain is the cyc2 gene product that involved in the oxidation process of iron. Materials and methods: Evaluation of UV mutated (60, 120 and 180s Acidithiobacillus sp. FJ2 cyc2gene in the presence of uranium ore concentrations, has been implemented in this project. For this purpose, the original and mutated bacteria were cultivated in the presence of uranium ore concentrations (5, 10, 15, 25 and 50%. Uranium extraction, variation of pH and Eh values were measured at 24 h intervals. Then, when the uranium extraction yield reached to 100%, gene expressions of cyc2 original and mutatedAcidithiobacillus sp. FJ2 were analyzed using Real-time PCR method. Results: The results of the experiments showed that, with increasing pulp density, the uranium extraction rate and oxidation activity of bacteria were reduced. In addition, the result of cyc2 gene expression showed that the target gene expression increases in the presence of uranium ore compared to sample with absence of uranium ore, andwith further increase of pulp density, due to the toxicity of uranium, shows a decreasing trend. Discussion and conclusion: The results of this study indicated that the mutation in the bacterium has a positive effect on the uranium bioleaching process, which can play an important role in the process of uranium bioleaching at high concentrations. In addition, with increasing pulp density due to uranium toxicity, there is a decreasing trend in the process of uranium extraction, which indicates the important role of this factor in the uranium bioleaching process.

  10. Uranium ores

    International Nuclear Information System (INIS)

    Poty, B.; Roux, J.

    1998-01-01

    The processing of uranium ores for uranium extraction and concentration is not much different than the processing of other metallic ores. However, thanks to its radioactive property, the prospecting of uranium ores can be performed using geophysical methods. Surface and sub-surface detection methods are a combination of radioactive measurement methods (radium, radon etc..) and classical mining and petroleum prospecting methods. Worldwide uranium prospecting has been more or less active during the last 50 years, but the rise of raw material and energy prices between 1970 and 1980 has incited several countries to develop their nuclear industry in order to diversify their resources and improve their energy independence. The result is a considerable increase of nuclear fuels demand between 1980 and 1990. This paper describes successively: the uranium prospecting methods (direct, indirect and methodology), the uranium deposits (economical definition, uranium ores, and deposits), the exploitation of uranium ores (use of radioactivity, radioprotection, effluents), the worldwide uranium resources (definition of the different categories and present day state of worldwide resources). (J.S.)

  11. Determination of rare earth elements in products of Chadormalu iron ore concentrator plant (Iran) from beneficiation point of view

    International Nuclear Information System (INIS)

    Jorjani, E.; Bagherieh, A. H.; Rezai, B.

    2007-01-01

    :Different samples have been prepared from different products in Chadormalu iron ore concentrator plant: Low intensity magnetite separators concentrate (magnetite concentrate), reverse flotation tail (final hematite concentrate), flotation concentrate (apatite concentrate), final tail (L.I. M.S. tail + reverse flotation concentrate + apatite flotation tail). The samples were used for rare earth elements (REEs) distribution and origin studies. The assay of REEs was determined by ICP-MS spectrometry. The amount of total (light and heavy) REEs were 9631, 291, 199, 2236 ppm and the distributions were 19.3, 3.6, 10.1, 67% in flotation concentrate (apatite concentrate), reverse flotation tail (hematite concentrate), magnetite concentrate and total tail respectively. About 19.3% of total REEs were distributed in apatite concentrate with an assay of 9631 ppm. Therefore, further studies have been conducted on this product. According to the Xray studies the minerals of fluoroapatite, ankerite and calcite are the main mineral phases in apatite concentrate which the apatite is dominant among them. The scanning electron microscopy studies were shown that the high amount of REEs distributed on fluoroapatite mineral. The results have clearly shown that the apatite concentrate that is a by product of iron dressing in Chadormalu plant, with a low economical value and left without any further treatment, can be used as a significant source of REEs. According to this characterization studies, the recovery of a mixed rare earth oxide from fluoroapatite is possible either with the treatment of liquors from the total dissolution of the ore in nitric acid or with the proposed treatment of the phosphogypsum by-product from the conventional sulphuric acid route and the recovery of rare earth oxides from phosphoric acid sludges that the detailed flowsheet needs further extraction work

  12. Method and apparatus for measuring the concentration of water, iron, and aluminum in iron ore by neutron radiation

    International Nuclear Information System (INIS)

    Holmes, R.J.; Wylie, A.W.; McCracken, K.G.

    1975-01-01

    Techniques and apparatus for measuring the concentration of water and specific components in materials are described. The techniques involve irradiating the material with neutrons and monitoring the neutron flux in the vicinity of the irradiated material and the gamma radiation from excited nuclei of the specific component. Examples of the use of the invention include on-stream monitoring of ores carried by conveyor belts and borehole logging using a probe which carries a neutron source, and neutron and gamma radiation detectors. (U.S.)

  13. Evaluation of bioleaching column test of sulphide copper ore and copper concentrate using preconditioned surface

    Directory of Open Access Journals (Sweden)

    Videla Leiva Alvaro

    2016-01-01

    Full Text Available Bacterial activity can be related to the presence of Fe+3 in the solution, which drives copper oxidation during the secondary copper low grade sulfide ore leaching process. The present work evaluates improvements in kinetics of leaching when ferroxidans are preconditioned in an inert surface helping to build a biofilm which improves metabolism of the colony. The present work shows evaluation using laboratory columns to perform bioleaching during a 30 days period under three conditions: a base column with no inert surface, a column with loofa available for bacterial growth and conditioning, and finally a column with the loofa surface ground and distributed in the column among the particles.

  14. The critical importance of pulp concentration on the flotation of galena from a low grade lead–zinc ore

    Directory of Open Access Journals (Sweden)

    Xianping Luo

    2016-04-01

    Full Text Available The Qixia orebody is a complex lead–zinc sulfide system with pyrite gangue and minor amounts of copper. In order to improve the flotation results, laboratory scale flotation testing of ore samples taken from this operation was performed. Flotation tests used a sequential recovery protocol for selective flotation of first the lead and thereafter the zinc. The key parameters that influence flotation performance of lead mineral were tested in this paper. The test data show that, for comparable collector, grinding time, flotation pH and solid-in-pulp concentration, the increase of solid-in-pulp concentration has the most significant effect on the recovery and selective separation of lead mineral. The increase of solid-in-pulp concentration from 27% to 55% makes the recovery of lead mineral increased from 60% to 80% and the lead grade increased from 27.5% to 29.1%.

  15. Development of the Facility for Transformation of Magnetic Characteristics of Weakly Magnetic Oxidized Iron Ores Related to Improvement of Technologies for Iron Ore Concentrate Production

    Directory of Open Access Journals (Sweden)

    Ponomarenko, O.M.

    2016-01-01

    Full Text Available New facility for continuous registration of iron ore magnetization depending on temperature by heating of iron ores upon reducing conditions was created. Facility allows to register the processes of transformation of weakly magnetic minerals into strongly magnetic ones under the influence of reducing agents and temperature, as well as to determine the Curie temperature of the minerals. Using created facility it was shown, that heating of goethite and hematite in the presence of 4 % of starch in the temperature range of 300—650 °С leads to significant increase of magnetization of the samples. X-Ray diffraction confirmed that under indicated conditions the structure of hematite and goethite is transformed into magnetite structure. Obtained results open up new possibilities for the development of effective technologies for oxidized iron ore beneficiation.

  16. Concentration of gold, sulphide minerals, and uranium oxide minerals by flotation from ores and metallurgical plant products

    International Nuclear Information System (INIS)

    Weston, D.

    1976-01-01

    A process is described for the concentration by flotation of gold, gold bearing minerals and uranium oxide minerals from ores and metallurgical plant products. A pulp of a ground ore is agitation conditioned in at least two agitation conditioning stages wherein in at least one stage the pH of the pulp is lowered with an acid agent to within the pH range of about 1.5 to 5.0, and wherein in at least one additional agitation conditioning stage the pH of the pulp is raised to within the pH range of about 6.0 to 11.0 and wherein in at least the last stage prior to flotation at least one collector selected from the group of sulfhydryl anionic collectors is present. Subsequently, the at least two stage agitation conditioned pulp is subjected to flotation to produce a flotation concentrate enriched in at least one of the mineral values from the group consisting of gold, gold bearing minerals and uranium minerals

  17. Fluorine concentrations of ore fluids in the Illinois-Kentucky district: Evidence from SEM-EDS analysis of fluid inclusion decrepitates

    Science.gov (United States)

    Kenderes, Stuart M.; Appold, Martin S.

    2017-08-01

    The Illinois-Kentucky district is an atypical occurrence of Mississippi Valley-type (MVT) mineralization that consists predominantly of fluorite rather than metal sulfide minerals. A long-standing assumption for the predominance of fluorite in the Illinois-Kentucky district is that the ore fluids there were anomalously rich in dissolved fluorine compared to typical sedimentary brines and other MVT ore fluids. This hypothesis is based on the unusual close temporal and spatial association of fluorine-rich ultramafic igneous rocks to MVT mineralization in the district, high K and Sr concentrations in the igneous rocks and in MVT ore-hosted fluid inclusions, a significant mantle 3He/4He component in ore-hosted fluid inclusions, and reaction path models that show titration of a HF-rich fluid into sedimentary brine is capable of producing a fluorite-dominated MVT ore mineral assemblage. The purpose of the present study was to test this hypothesis more directly by determining the fluorine concentration of the Illinois-Kentucky ore fluid through SEM-EDS analysis of evaporative solute mounds resulting from thermal decrepitation of fluid inclusions hosted in sphalerite. All 26 evaporative solute mounds from Illinois-Kentucky sphalerite samples analyzed contained detectable concentrations of fluorine of 1-4 weight percent. Based on calibration to standard solutions and previously published fluid inclusion major element concentrations, these solute mound fluorine concentrations correspond to fluid inclusion fluorine concentrations of about 680-4300 ppm, indicating that the Illinois-Kentucky ore fluids were quite rich in fluorine compared to typical sedimentary brines, which have fluorine concentrations mainly on the order of 1's to 10's of ppm. In contrast, solute mounds from sphalerite-hosted fluid inclusions from the Tri-State district did not contain fluorine in excess of the detection limit. The detection limit equates to an aqueous fluorine concentration between 87 and

  18. Investigation of ore processing to recover uranium concentrate from sandstone of Pa Lua area on scale of 2 tons of ore per batch

    International Nuclear Information System (INIS)

    Cao Hung Thai; Dinh Manh Thang; Tran Van Son; Le Quang Thai; Bui Dang Hanh; Hoang Bich Ngoc; Nguyen Hong Ha; Phung Vu Phong; Nguyen Khac Tuan

    2003-01-01

    Based on the laboratory results, a system for testing on scale of 2 tons uranium ore per batch including following parts was established: equipment for crushing and grinding, equipment for acid leaching, equipment for impurity precipitation and filtration and drying. the results of testing by 2 tons ore per batch scale shown that uranium recovery in the leach circuit were achieved of at least 90% under following conditions: The supplying rate of leach agent 50-701/m 2 .h, sandstone is mixed or incubated with acid before the percolation. About 23 kg filter cake per m 3 solution were disposed as tailings. Flocculants N101, A101 (TOAGOSEL, Japan) were used for improvement of filtration and washing capacity of impurity precipitation. Uranium peroxide was precipitated with addition of hydrogen peroxide. The underflow solids were filtered and calcined. The product contained min. 76% U 3 O 8 . The water recycle was successfully tested. That results in minimization of water addition to only 0.3m 3 /ton of ore. Experimental results on 2 tons scale showed that the proposed processing flow sheet using direct precipitation can meet all environmental and technical objectives. (CHT)

  19. Characterization and concentration of manganese ore waste; Caracterizacao e concentracao de rejeito de minerio de manganes

    Energy Technology Data Exchange (ETDEWEB)

    Lima, Rosa Malena Fernandes; Pereira, Eder Esper; Reis, Erica Linhares; Silva, Glaucia Regina da [Universidade Federal de Ouro Preto (UFOP), MG (Brazil)

    2010-07-01

    In this work is presented the tests results of characterization and concentration by gravity and flotation methods carried out with a manganese sample waste. By optical microscopy, SEM/EDS and X-ray diffractometry were identified the Mn minerals spessartite (20%), tephroite (15%), rhodonite (5%), rhodochrosite and carbonates minerals (29%), opaque minerals and others (16%), micaceus minerals (6%) and quartz (4%). It was obtained Mn metallurgical recovery of 58% with Mn concentrate contents varying from 30 to 32.5%. The concentrates SiO{sub 2} contents of flotation were until 1.5% smaller than those contents of gravity method concentrates. (author)

  20. Feasibility study of the dissolution rates of uranium ore dust, uranium concentrates and uranium compounds in simulated lung fluid

    International Nuclear Information System (INIS)

    Robertson, R.

    1986-01-01

    A flow-through apparatus has been devised to study the dissolution in simulated lung fluid of aerosol materials associated with the Canadian uranium industry. The apparatus has been experimentally applied over 16 day extraction periods to approximately 2g samples of < 38um and 53-75um particle-size fractions of both Elliot Lake and Mid-Western uranium ores. The extraction of uranium-238 was in the range 24-60% for these samples. The corresponding range for radium-226 was 8-26%. Thorium-230, lead-210, polonium-210, and thorium-232 were not significantly extracted. It was incidentally found that the elemental composition of the ores studied varies significantly with particle size, the radionuclide-containing minerals and several extractable stable elements being concentrated in the smaller size fraction. Samples of the refined compounds uranium dioxide and uranium trioxide were submitted to similar 16 day extraction experiments. Approximately 0.5% of the uranium was extracted from a 0.258g sample of unsintered (fluid bed) uranium dioxide of particle size < 38um. The corresponding figure for a 0.292g sample of uranium trioxide was 97%. Two aerosol samples on filters were also studied. Of the 88ug uranium initially measured on stage 2 of a cascade impactor sample collected from the yellow cake packing area of an Elliot Lake mill, essentially 100% was extracted over a 16 day period. The corresponding figure for an open face filter sample collected in a fuel fabrication plant and initially measured at 288ug uranium was approximately 3%. Recommendations are made with regard to further work of a research nature which would be useful in this area. Recommendations are also made on sampling methods, analytical methods and extraction conditions for various aerosols of interest which are to be studied in a work of broader scope designed to yield meaningful data in connection with lung dosimetry calculations

  1. Wet high-intensity magnetic separation for the concentration of Witwatersrand gold-uranium ores and residues

    International Nuclear Information System (INIS)

    Corrans, I.J.; Levin, J.

    1979-01-01

    Wet high-intensity magnetic separation (WHIMS) for the concentration of gold and uranium was tested on many Witwatersrand cyanidation residues, and on some ores and flotation tailings. The results varied, but many indicated recoveries of over 60 per cent of the gold and uranium. The main source of loss is the inefficiency of WHIMS for material of smaller particle size than 20μm. The recoveries in the continuous tests were lower than those in the batch tests. The continuous tests indicated an operational difficulty that could be experienced in practice, namely the tendency for wood chips and ferromagnetic particles to block the matrix of the separator. It was decided that a solution to the problem lies in the modification of the separator to allow continuous removal of the matrix for cleaning. A system has been developed for this purpose and is being demonstrated on a pilot-plant scale. Promising results were obtained in tests on a process that combines a coarse grind, gravity concentration, and WHIMS. In the gravity-concentration step, considerable recoveries, generally over 50 per cent, of high-grade pyrite were obtained, together with high recoveries of gold and moderate, but possibly important, recoveries of uranium. A simple model describing the operation of the WHIMS machine in terms of the operating parameters is described. This should reduce the amount of empirical testwork required for the optimization of operating conditions and should provide a basis for scale-up calculations. The economics of the WHIMS process is discussed [af

  2. Determination of soil, sand and ore primordial radionuclide concentrations by full-spectrum analyses of high-purity germanium detector spectra

    International Nuclear Information System (INIS)

    Newman, R.T.; Lindsay, R.; Maphoto, K.P.; Mlwilo, N.A.; Mohanty, A.K.; Roux, D.G.; Meijer, R.J. de; Hlatshwayo, I.N.

    2008-01-01

    The full-spectrum analysis (FSA) method was used to determine primordial activity concentrations (ACs) in soil, sand and ore samples, in conjunction with a HPGe detector. FSA involves the least-squares fitting of sample spectra by linear combinations of 238 U, 232 Th and 40 K standard spectra. The differences between the FSA results and those from traditional windows analyses (using regions-of-interest around selected photopeaks) are less than 10% for all samples except zircon ore, where FSA yielded an unphysical 40 K AC

  3. Carbothermic reduction behaviors of Ti-Nb-bearing Fe concentrate from Bayan Obo ore in China

    Science.gov (United States)

    Wang, Guang; Du, Ya-xing; Wang, Jing-song; Xue, Qing-guo

    2018-01-01

    To support the development of technology to utilize low-grade Ti-Nb-bearing Fe concentrate, the reduction of the concentrate by coal was systematically investigated in the present paper. A liquid phase formed when the Ti-Nb-bearing Fe concentrate/coal composite pellet was reduced at temperatures greater than 1100°C. The addition of CaCO3 improved the reduction rate when the slag basicity was less than 1.0 and inhibited the formation of the liquid phase. Mechanical milling obviously increased the metallization degree compared with that of the standard pellet when reduced under the same conditions. Evolution of the mineral phase composition and microstructure of the reduced Ti-Nb-bearing Fe concentrate/coal composite pellet at 1100°C were analyzed by X-ray diffraction and scanning electron microscopy-energy-dispersive spectroscopy. The volume shrinkage value of the reduced Ti-Nb-bearing Fe concentrate/coal composite pellet with a basicity of 1.0 was approximately 35.2% when the pellet was reduced at 1100°C for 20 min, which enhanced the external heat transfer to the lower layers when reduced in a practical rotary hearth furnace. The present work provides key parameters and mechanism understanding for the development of carbothermic reduction technology of a Ti-Nb-bearing Fe concentrate incorporated in a pyrometallurgical utilization flow sheet.

  4. Natural uranium concentrations of native plants over a low-grade ore body

    International Nuclear Information System (INIS)

    Sheppard, M.I.; Thibault, D.H.

    1984-01-01

    Plant uranium concentrations generally reflect soil or rock substrate concentrations in upland areas, but they may not in lowland areas where the rhizoids of Sphagnum spp. and rocks of Ledum groenlandicum may be in direct contact either continuously or on a seasonal basis with the groundwater. This study points out the importance of selecting plant species and collection sites where the true substrate can be well defined and sampled. Sphagnum spp. and Ledum groenlandicum best reflect the substrate uranium concentrations in lowland areas, Umbilicaria spp. and Cladonia spp. in rock outcrop, and Picea mariana and Betula papyrifera in upland locations. The study shows the best plant part to sample is the older tissue such as the stems, twigs, and wood. Since no systematic changes in plant tissue concentrations were found throughout the season, sampling can be carried out anytime. Expression of soil concentrations on an ash weight basis gave a considerably different result than those on a dry weight basis, particularly when comparisons were made between litter-enriched mineral soil and true organic soils. The amount of ash varied among plant organs, species, and taxonomic divisions, and a constant value cannot be used to convert plant ash concentrations on a dry weight basis

  5. Leaching kinetics of neodymium in sulfuric acid of rare earth elements (REE) slag concentrated by pyrometallurgy from magnetite ore

    International Nuclear Information System (INIS)

    Yoon, Ho-Sung; Kim, Chul-Joo; Chung, Kyung Woo; Lee, Jin-Young; Shin, Shun Myung; Lee, Su-Jeong; Joe, A-Ram; Lee, Se-Il; Yoo, Seung-Joon

    2014-01-01

    We studied the leaching kinetics of recovering neodymium in sulfuric acid from the rare earth elements (REE) slag concentrated by smelting reduction from a magnetite ore containing monazite. The leaching kinetics on neodymium was conducted at a reactant concentration of 1.5 g REE slag per L of 0.3M H 2 SO 4 , agitation of 750 rpm and temperature ranging from 30 to 80 .deg. C. Neodymium oxide included in the REE slag was completely converted into neodymium sulfate phase (Nd 2 (SO 4 ) 3 ) in H 2 SO 4 after the leaching of 5 h, 80 .deg. C. As a result, the leaching mechanism was determined in a two-stage model based on the shrinking core model with spherical particles. The first step was determined by chemical reaction, and the second step was determined by ash layer diffusion because the leaching of REEs by the first chemical reaction increases the formation of the ash layer affecting as a resistance against the leaching. By using the Arrhenius expression, the apparent activation energy of the first chemical reaction step was found to be 9 kJmol -1 . After the first chemical reaction, leaching reaction rate was determined by the ash layer diffusion. The apparent activation energy of ash layer diffusion was found to be 32 kJmol -1

  6. Leaching kinetics of neodymium in sulfuric acid of rare earth elements (REE) slag concentrated by pyrometallurgy from magnetite ore

    Energy Technology Data Exchange (ETDEWEB)

    Yoon, Ho-Sung; Kim, Chul-Joo; Chung, Kyung Woo; Lee, Jin-Young; Shin, Shun Myung [Korea Institute of Geoscience and Mineral Resources (KIGAM), Daejeon (Korea, Republic of); Lee, Su-Jeong; Joe, A-Ram; Lee, Se-Il; Yoo, Seung-Joon [Seonam University, Asan (Korea, Republic of)

    2014-10-15

    We studied the leaching kinetics of recovering neodymium in sulfuric acid from the rare earth elements (REE) slag concentrated by smelting reduction from a magnetite ore containing monazite. The leaching kinetics on neodymium was conducted at a reactant concentration of 1.5 g REE slag per L of 0.3M H{sub 2}SO{sub 4}, agitation of 750 rpm and temperature ranging from 30 to 80 .deg. C. Neodymium oxide included in the REE slag was completely converted into neodymium sulfate phase (Nd{sub 2}(SO{sub 4}){sub 3}) in H{sub 2}SO{sub 4} after the leaching of 5 h, 80 .deg. C. As a result, the leaching mechanism was determined in a two-stage model based on the shrinking core model with spherical particles. The first step was determined by chemical reaction, and the second step was determined by ash layer diffusion because the leaching of REEs by the first chemical reaction increases the formation of the ash layer affecting as a resistance against the leaching. By using the Arrhenius expression, the apparent activation energy of the first chemical reaction step was found to be 9 kJmol{sup -1}. After the first chemical reaction, leaching reaction rate was determined by the ash layer diffusion. The apparent activation energy of ash layer diffusion was found to be 32 kJmol{sup -1}.

  7. Research on the possibility of concentrating low-grade uranium ores by bacterial leaching. Part of a coordinated programme on the bacterial leaching of uranium ores

    International Nuclear Information System (INIS)

    Tataru, S.

    1978-12-01

    Effect of extraction reagents with solvents on the bacteria and the influence of eluants on the bacteria development was studied. To establish the effects of various solvents and eluants on the development of bacteria, on oxidizing capacity of Fe 2+ to Fe 3+ , and to study their influence on bacteria morphology, bacteria strains were contacted with Alamine 336, trioctylamine, LIX and nitric eluant. Bacteria development and the oxidizing ability of Fe 2+ to Fe 3+ were significantly inhibited and morphological changes of individuals in the bacteria population were found. The bacteria populations resulted from ores had a more decreased resistance as the bacteria culture was better selected by repeated inoculations and incubations. In case of the bacterial leaching in heap or in situ a periodical extraction with solvents is required in order to allow the bacteria population between successive extraction stage be remade

  8. Code of Practice on radiation protection in the mining and milling of radioactive ores (1980) - Guidelines for storage and packaging of uranium concentrates

    International Nuclear Information System (INIS)

    1986-01-01

    This Guideline is intended to provide assistance in the application of the 1980 Code of Practice on radiation protection in mining and milling of radioactive ores. Its purpose is to give advice relevant to the design, construction and operation of an uranium concentrate storage and packaging facility in which exposure to ionizing radiation from uranium-bearing concentrate will not only conform to the Code, but will also be as low as reasonably achievable. (NEA) [fr

  9. Carbothermal Reduction of Iron Ore in Its Concentrate-Agricultural Waste Pellets

    Directory of Open Access Journals (Sweden)

    Zhulin Liu

    2018-01-01

    Full Text Available Carbon-containing pellets were prepared with the carbonized product of agricultural wastes and iron concentrate, and an experimental study on the direct reduction was carried out. The experimental results demonstrated that carbon-containing pellets could be rapidly reduced at 1200 to 1300°C in 15 minutes, and the proper holding time at high temperature was 15 to 20 min. The degree of reduction gradually increased with temperature rising, and the appropriate temperature of reducing pellets was 1200°C. The weight loss rate and reduction degree of pellets increased with the rise of carbon proportion, and the relatively reasonable mole ratio of carbon to oxygen was 0.9. A higher content of carbon and an appropriate content of volatile matters in biomass char were beneficial to the reduction of pellets. The carbon-containing pellets could be reduced at high speeds in the air, but there was some reoxidization phenomenon.

  10. Development and functioning of microorganisms in concentration cycles of sulfide copper-nickel and non-sulfide apatite-nepheline ores

    Directory of Open Access Journals (Sweden)

    Fokina N. V.

    2017-03-01

    Full Text Available The number and trophic diversity of bacteria in flotation samples of apatite-nepheline and sulfide copper-nickel ores at the concentration plants of JSC "Apatite" and Kola Mining and Metallurgical Company have been determined. The study of the size and diversity of the microbiota has been conducted by culture on selective nutrient media. The total number and biomass of bacteria have been considered by fluorescence microscopy using Cyclopore polycarbonate membrane filters. Bacteria have been identified by molecular genetic methods. The least amount of both saprotrophic and other trophic groups of bacteria has been observed in the samples of ore and recycled water as at the concentrating factory of Apatit JSC, and also at the plant "Pechenganikel". It has been found out that the bacteria contained in the ore and recycling water flowing from the tailings increased their number during the flotation process due to coming of the nutrients with the flotation reagents, aeration and increased temperature. Strains which occurrence is more than 60 % have been extracted from recycled water and basic flotation products and classified as Pseudomonas. Two strains with occurrence of more than 60 % have been discovered at Apatit JSC and classified as Stenotrophomonas and Acinetobacter. The number of fungi in the cycle of apatite-nepheline ore enrichment at the factories is very low (1 to 24 CFU / 1 ml or 1 g of ore. Fungi of the genus Penicillium have been dominated, fungi of the genera Acremonium, Aureobasidium, Alternaria, Chaetomium have also been detected. At the plant "Pechenganikel" species Aspergillus fumigatus, Penicillium aurantiogriseum and P. glabrum have been extracted. It has been shown that the bacteria deteriorate the apatite flotation as a result of their interaction with active centers of calcium-containing minerals and intensive flocculation decreasing the floatation selectivity. Also some trend of copper and nickel recovery change has been

  11. Uranium Ore and Concentrate Sampling; Echantillonnage des Minerais et des Concentres d'Uranium; Otbor prob uranovoj rudy i kontsentratov; Muestreo de Minerales y Concentrados de Uranio

    Energy Technology Data Exchange (ETDEWEB)

    McGinley, F. E.; Brown, D. L.; Langridge, R. W. [United States Atomic Energy Commission, Grand Junction, CO (United States)

    1966-02-15

    The Grand Junction Office of the United States Atomic Energy Commission has been responsible for procuring large quantities of natural uranium in both ores and concentrates. The techniques used for sampling ores are necessarily different from those used for concentrates. Each step in the overall measurement and sampling systems for both ores and concentrates is discussed, giving particular attention to the accuracy and precision of that step. During the years 1948-1964, a total of 58 million tons of ore was sampled in about 40 different mechanical sampling plants in the western United States. All plants have been required to weigh, sample and analyse ore in accordance with practices satisfactory to the USAEC. The ordinary principles of ore sampling, as used for years in the mining industry, have been followed. However, sufficient check sampling and other tests were performed to ensure that the uranium content of the variety of ores sampled was as accurately determined as economically feasible. Concentrates containing about 129 000 t of U{sub 3}O{sub 8} were purchased from domestic producers during the last 17 years. This uranium was contained in approximately 10 000 lots, each of which was weighed, sampled, and analysed in accordance with carefully controlled procedures. These lots were received at USAEC-owned sampling facilities at Grand Junction or Weldon Spring, Missouri, both of which are contractor operated. The average lot consists of about 50 drums (55-gallon size) and weighs approximately 35 000 lb. Because concentrate varies so much in both physical and chemical characteristics, it is necessary to sample each drum. Through the years, various sampling systems were used, such as pipes, open auger, enclosed augers, and falling stream sampling. Falling stream sampling is the most accurate, provided precautions are taken to prevent changes in weight due to exposure to the atmosphere. Because of the tendency of concentrates to sorb or desorb moisture, depending

  12. Concentration of gold, sulphide minerals and uranium oxide minerals by flotation from ores and metallurgical plant products

    International Nuclear Information System (INIS)

    Weston, D.

    1974-01-01

    A process for the recovery by froth flotation of gold and mineral values selected from the group consisting of gold bearing minerals, platinum group minerals, silver group minerals, and uranium group minerals, from ores and metallurgical plant products containing at least gold and at least one of the other said minerals comprising: subjecting a suitably prepared pulp of the material to mechanical agitation in at least one agitation conditioning stage wherein the pH of the said pulp has been lowered with an acid agent to an optimum pH point within the pH range of about 1.5 to 5.0 and wherein the agitation conditioning is for a sufficient period of time to bring about heavy activation of at least one of the said mineral values in at least one subsequent mechanical agitation conditioning stage wherein the said pulp is further agitation conditioned for a sufficient period of time and at an optimum pH point in the pH range of about 6.0 to 11.0 in the presence of at least one collector selected from the group of sulfhydryl anionic collectors to produce the said heavy activation of at least gold and at least one of the other said mineral values; and subsequently in the presence of a frother subjecting and said agitation conditioned pulp to flotation to produce a concentrate enriched in gold and at least one of the othersaid mineral values, and a tailings product impoverished in at least gold and at least one of the other said mineral values

  13. Behaviour of the pH adjustment, Ion exchange and concentrate precipitation stages in the acid leaching of uranium phosphate ores

    International Nuclear Information System (INIS)

    Estrada Aguilar, J.; Uriarte Hueda, A.

    1962-01-01

    The uranium recovery from acid leach solutions of uranium-phosphate ores has been studied. Relations have been found between the solution characteristics and the results obtained at different stages of the process. The following data can thus be predicted: solids to remove and uranium recovery in the pH adjustment stage, uranium capacity of the resin, more suitable eluating agent, elution velocity and uranium concentration in the eluate in the ion exchange stage, and composition of the concentrate produced by direct precipitation of the eluate in the concentrate precipitation stage. (Author) 8 refs

  14. Investigating concentration distributions of arsenic, gold and antimony in grain-size fractions of gold ore using instrumental neutron activation analysis

    International Nuclear Information System (INIS)

    Nyarku, M.; Nyarko, B.J.B.; Serfor-Armah, Y.; Osae, S.

    2010-01-01

    Instrumental neutron activation analysis (INAA) has been used to quantify concentrations of arsenic (As), gold (Au) and antimony (Sb) in grain-size fractions of a gold ore. The ore, which was taken from the Ahafo project site of Newmont Ghana Gold Ltd., was fractionated into 14 grain-size fractions using state-of-the-art analytical sieve machine. The minimum sieve mesh size used was 36 μm and grains >2000 μm were not considered for analysis. Result of the sieving was analysed with easysieve (registered) software. The<36 μm subfraction was found to be the optimum, hosting bulk of all three elements. Arsenic was found to be highly concentrated in<36-100 μm size fractions and erratically distributed in from 150 μm fraction and above. For gold, with the exception of the subfraction <36 μm which had exceptionally high concentration, the element was found to be approximately equally distributed in all the size fractions but slightly 'played out' in 150-400 μm size fractions. Antimony occurrence in the sample was relatively high in <36 μm size fraction followed by 600, 800, 400 and 36 μm size fractions in that order. Gold content in the sample was comparatively far greater than arsenic and antimony; this is indicative of level of gold mineralization in the concession where the sample ore was taken. The concentration of gold in the composite sample was in the range 564-8420 ppm as compared to 14.33-186.92 ppm for arsenic and 1.09-9.48 ppm for antimony. Elemental concentrations were correlated with each other and with grain-size fractions and the relationships between these descriptive parameters were established.

  15. Inhalation of uranium ores

    International Nuclear Information System (INIS)

    Stuart, B.O.; Jackson, P.O.

    1975-01-01

    In previous studies the biological dispositions of individual long-lived alpha members of the uranium chain ( 238 U, 234 U and 230 Th) were determined during and following repeated inhalation exposures of rats to pitchblende (26 percent U 3 O 8 ) ore. Although finely dispersed ore in secular equilibrium was inhaled, 230 Th/ 234 U radioactivity ratios in the lungs rose from 1.0 to 2.5 during 8 weeks of exposures and increased to 9.2 by four months after cessation of exposures. Marked non-equilibrium levels were also found in the tracheobronchial lymph nodes, kidneys, liver, and femur. Daily exposures of beagle dogs to high levels of this ore for 8 days resulted in lung 230 Th/ 234 U ratios of >2.0. Daily exposures of dogs to lower levels (0.1 mg/1) for 6 months, with sacrifice 15 months later, resulted in lung and thoracic lymph node 230 Th/ 234 U ratios ranging from 3.6 to 9 and nearly 7, respectively. The lungs of hamsters exposed to carnotite (4 percent U 3 O 8 ) ore in current lifespan studies show 230 Th/ 234 U ratios as high as 2.0 during daily inhalation of this ore in secular equilibrium. Beagle dogs sacrificed after several years of daily inhalations of the same carnotite ore plus radon daughters also showed marked non-equilibrium ratios of 230 Th/ 234 U, ranging from 5.6 to 7.4 in lungs and 6.2 to 9.1 in thoracic lymph nodes. This pattern of higher retention of 230 Th than 234 U in lungs, thoracic lymph nodes, and other tissues is thus consistent for two types of uranium ore among several species and suggests a reevaluation of maximum permissible air concentrations of ore, currently based only on uranium content

  16. Ore sorting

    International Nuclear Information System (INIS)

    Hawkins, A.P.; Richards, A.W.

    1982-01-01

    In an ore sorting apparatus, ore particles are bombarded with neutrons in a chamber and sorted by detecting radiation emitted by isotopes of elements, such as gold, forming or contained in the particles, using detectors and selectively controlling fluid jets. The isotopes can be selectively recognised by their radiation characteristics. In an alternative embodiment, shorter life isotopes are formed by neutron bombardment and detection of radiation takes place immediately adjacent the region of bombardment

  17. Study on Yen Phu rare earth ore concentrate treatment technology and separation of major heavy rare earth elements by solvent extraction method

    International Nuclear Information System (INIS)

    Le Ba Thuan; Pham Quang Trung; Vu Lap Lai

    2003-01-01

    1. Yenphu rare earth ore concentrate treatment by alkali under pressure: On the base of studying mineral and chemical compositions of Yenphu rare earth ore concentrate containing 28% TREO and conditions for digestion of ore concentrate by alkali under pressure such as ore concentrate/ NaOH ratio, alkali concentration, pressure and temperature at bench scale (100 gram and 5 kg per batch), the optimal conditions for decomposition of REE ore concentrate have been determined. The yield of the decomposition stage is about 90%. The studies on alkali washing, REE leaching by HCl, pH for leaching process, and iron and radioactive impurities removing by Na 2 S + Na 2 PO 4 have been carried out. The obtained results show that mixture of Na 2 S 5% + Na2PO 4 1% is effective in iron and radioactive impurities removing. The obtained REE oxides get purity of > 99% and meet the need of solvent extraction (SX) individual separation of rare earth elements. The schema for recovery of REEs from Yenphu REE ore concentrate by alkali decomposition under high pressure has been proposed. 2. Fractionation of Yenphu rare earth mixture into subgroups by solvent extraction with PC88A: On the base of simulation program, the parameters for fractional process of rare earths mixture into subgroups by solvent extraction with PC88A have been proposed and determined by experimental verification on mixer-settler set. According to this process, rare earths mixture fractionated into yttrium and light subgroups. In their turn, the light subgroup was separated into light (La, Ce, Pr, Nd) and middle (Sm, Eu, Gd) subgroups. The average yield of the process reached value > 95%. The composition of light subgroup meets the needs for individual separation of Gd, Eu, and Sm. 3. Separation and purification of yttrium: The process for recovery of yttrium consists of two stages: upgrade to get high quality Y concentrate by PC88A and purification by Aliquat 336 in NH 4 SCN-NH 4 Cl medium. The process parameter for

  18. Determination of elemental impurities and U and O isotopic compositions with a view to identify the geographical and industrial origins of uranium ore concentrates

    Science.gov (United States)

    Salaun, A.; Hubert, A.; Pointurier, F.; Aupiais, J.; Pili, E.; Richon, P.; Fauré, A.; Diallo, S.

    2012-12-01

    First events of illicit trafficking of nuclear and radiological materials occurred 50 years ago. Nuclear forensics expertise are aiming at determining the use of seized material, its industrial history and provenance (geographical area, place of production or processing), at assisting in the identification and dismantling of illicit trafficking networks. This information is also valuable in the context of inspections of declared facilities to verify the consistency of operator's declaration. Several characteristics can be used to determine the origin of uranium ore concentrates such as trace elemental impurity patterns (Keegan et al., 2008 ; Varga et al., 2010a, 2010b) or uranium, oxygen and lead isotopic compositions (Tamborini et al., 2002a, 2002b ; Wallenius et al., 2006; Varga et al., 2009). We developed analytical procedures for measuring the isotopic compositions of uranium (234U/238U and 235U/238U) and oxygen (18O/16O) and levels of elemental impurities (e.g. REE, Th) from very small amounts of uranium ore concentrates (or yellow cakes). Micrometer particles and few milligrams of material are used for oxygen isotope measurements and REE determination, respectively. Reference materials were analyzed by mass spectrometry (TIMS, SF-ICP-MS and SIMS) to validate testing protocols. Finally, materials of unknown origin were analyzed to highlight significant differences and determine whether these differences allow identifying the origin of these ore concentrates. References: Keegan, E., et al. (2008). Applied Geochemistry 23, 765-777. Tamborini, G., et al. (2002a). Analytical Chemistry 74, 6098-6101. Tamborini, G., et al. (2002b). Microchimica Acta 139, 185-188. Varga, Z., et al. (2009). Analytical Chemistry 81, 8327-8334. Varga, Z., et al. (2010a). Talanta 80, 1744-1749. Varga, Z., et al. (2010b). Radiochimica Acta 98, 771-778 Wallenius, M., et al. (2006). Forensic Science International 156, 55-62.

  19. Extraction of vanadium from campo Alegre de Lourdes (BA, Brazil) Fe-Ti-V ore by partial reduction/magnetic concentration/salt roasting/hot water leaching

    International Nuclear Information System (INIS)

    Alcantara, E.M.; Ogasawara, T.; Silva, F.T. da; Fontes, E.F.

    1988-01-01

    A process under development at COPPE/UFRJ to rocover vanadium from a titaniferous magnetite type ore from Campo Alegre de Lourdes (Bahia, Brazil), throxgh magnetizing roasting/magnetic concentration/ salt roasting/hot water leaching, is described. The results of the experimental work carried cut up to present are in qualitative agrement with those of othar studies on salt roasting/water leaching of titaniferous magnetites. Is is discussed the existing relationship between the maximum percentags of vanadium extraction in the leaching and the salt roasting conditions. (author) [pt

  20. Determination of concentration levels of arsenic, gold and antimony in particle-size fractions of gold ore using Neutron Activation Analysis

    International Nuclear Information System (INIS)

    Nyarku, M.

    2009-02-01

    Instrumental Neutron Activation Analysis (INAA) has been used to quantify the concentrations of arsenic, gold and antimony in particle-size fractions of a gold ore. The ore, which was taken from the Ahafo project site of Newmont Ghana Gold Ltd, was first fractionated into fourteen (14) particle-size fractions using state-of-the-art analytical sieve machine. The minimum sieve mesh size used was 36 microns and grains >2000 microns were not considered for analysis. Results of the sieving were analysed with easysieve software. The < 36 microns sub fraction was found to be the optimum, hosting bulk of all three elements. For arsenic, the element was found to be highly concentrated in < 36 to +100 microns size fractions and erratically distributed from +150 microns fraction and above. For gold, in exception of the sub fraction <36 which had exceptionally high concentration, the element is distributed in all the size fractions but slightly 'plays out' in the +150 to +400 microns fractions. Antimony occurrence in the sample was relatively high in <36 microns size fraction followed by 600 - 800, 800 - 1000, 400 - 600 and 36 - 40 microns size fractions in that order. Gold content in the sample was far higher than that of arsenic and antimony. Gold concentration in the composite sample was in the range 564 - 8420 ppm. Arsenic levels were higher as compared to antimony. The range of arsenic concentration in the composite sample was 14.33 - 186.92 ppm. Antimony concentration was in the range 1.09 - 9.48 ppm. (au)

  1. Distribution of the ore elements in ore bodies of the Zapolyarnoe field (Kola Peninsula

    Directory of Open Access Journals (Sweden)

    D. V. Taymasov

    2017-12-01

    Full Text Available The author conducted studies of the chemical zonality of ore deposits of all types for the sulfide-copper-nickel deposit Zapolyarnoe. Within the deposit of sulfide-copper-nickel ores Zapolyarnoe are the following industrial types of ores: rich interspersed ores, which are interspersed mineralization in peridotites; brecciated ores formed by detrital material; poor interspersed ores characterized by vein-interspersed mineralization; solid ores in a form of massive sulphide emissions. This work is based on operational and detailed exploration data. The author sorted samples according to the types of ores. Using the results, the author derived regression lines and their formulas to rectilinear dependencies. Analysis of the graphs showed that for all types of ores the dependences of copper and cobalt content on nickel content are direct, but at that, in thick-interspersed and brecciated types they are similar, and in scattered-interspersed they differ significantly. It becomes clear that correlation of copper and nickel in ore body depends on the scattered-interspersed ores, whereas the correlation of cobalt and nickel is determined mainly by thick-interspersed and brecciated ores. Dependencies between nickel, copper and cobalt in ores change when concentration of nickel in the ore changes. The graphs also show that the ratio of Ni/Cu in breccias and scattered-interspersed ores, as well as in near-ore metaperidotites, is almost constant at different nickel concentrations, on average 2:1.5 and 1, respectively. Thick- interspersed ores show the tendency towards an increase in the ratio with an increase in nickel content. The Ni/Co ratio increases with an increase of Ni concentration in all types of ores. In rich ores, growth occurs along a stepped curve, and in breccias – rectilinearly. Thus, the analysis of distribution of ore elements in ore bodies indicates a complex heterogeneous composition of sulphide mineralizations in different types of ores

  2. Method of continuous pressure leaching of ores

    International Nuclear Information System (INIS)

    Fiala, P.; Baloun, S.; Polansky, M.

    1987-01-01

    Ore leaching, especially suspensions of ground ore or fine ore fractions from physical treatment was divided into two operations. The former, i.e., ore mixing with technical grade concentrated sulfuric acid proceeded in a separate mixer. The mixture was then transported into an autoclave where the actual leaching proceeded for 2 to 4 hours. The extracted mixture was discharged through the autoclave bottom. The leaching autoclave used can be without any inner structures. The separation of mixing from the actual leaching allows processing ores with high levels of clay components, increasing operating reliability of the facility, reducing consumption of special structural materials and energy, and increasing process efficiency. (E.S.)

  3. Microbial reduction of iron ore

    Science.gov (United States)

    Hoffmann, M.R.; Arnold, R.G.; Stephanopoulos, G.

    1989-11-14

    A process is provided for reducing iron ore by treatment with microorganisms which comprises forming an aqueous mixture of iron ore, microorganisms operable for reducing the ferric iron of the iron ore to ferrous iron, and a substrate operable as an energy source for the microbial reduction; and maintaining the aqueous mixture for a period of time and under conditions operable to effect the reduction of the ore. Preferably the microorganism is Pseudomonas sp. 200 and the reduction conducted anaerobically with a domestic wastewater as the substrate. An aqueous solution containing soluble ferrous iron can be separated from the reacted mixture, treated with a base to precipitate ferrous hydroxide which can then be recovered as a concentrated slurry. 11 figs.

  4. Effect of mining on heavy metal concentration in soils from the vicinity of Itakpe iron ore mine in kogi state, nigeria

    International Nuclear Information System (INIS)

    Amune, C.O.M.; Kakulu, S.

    2013-01-01

    The effects of mining oil from 1takpe iron ore mining area in Kogi State, Nigeria were studied through the determination of the heavy metals (Cd, Cu, Mg, Ni. Ph and Zn) using flame atomic absorption spectroscopy. Soil samples were collected during the dry and rainy seasons. Significant levels of heavy metals were found. Median topsoil concentrations (0-15 cm) for Ed, Cu, Mg, Ni, Pb and Zn were 0.16+0.02, 0.151-0.03, 0.041+0.03, 0.110.02, 0.07+0.(0 1, 0.04+0.04, micro/g, respectively. The heavy metal concentrations of control soil were relatively lower than those in the 1takpe mining environment soil and within levels of total metal contamination nation in the normal soil content intervals and maximum allowable limits of heavy metals in soils. Correlations analysis shows that heavy metals were closely correlated with each other except for Pb, indicating the studied metals are from the same pollutant resource. This shows, mining as contributing to the metallic levels in the 1takpe mining site. (author)

  5. The genesis of ores

    International Nuclear Information System (INIS)

    Brimhall, G.

    1991-01-01

    Human history and technology have been shaped by metals. How did they become concentrated in minable deposits located so conveniently near the earth's surface? The author explains the mechanisms of fluid transport-by magma, water and even air and wind-responsible for the chemical and physical interactions that created bodies of metallic ores throughout geologic history. From their formation to their modification at the surface of the earth, ore deposits are geologically transitory and reflect dynamic processes within the earth as well as atmospheric and climatic influences on hydrologic systems. As highly reactive supracrustal systems, they then serve as geochemical sensors providing a powerful record and set of tracer elements for deducing the history, transport paths and forces operative in the crust

  6. Uraniferous concentrations in the Francevillian of Gabon: their association with fossil hydrocarbon-bearing ore deposits of the lower Proterozoic

    International Nuclear Information System (INIS)

    Gauthier-Lafaye, Francois; Weber, Francis

    1981-01-01

    The Francevillian U deposits of Gabon are located in one of the oldest non metamorphic sedimentary series of the Lower Proterozoic 2150 M.Y. old. The uraniferous mineralization 2050 M.Y. old is strongly related to organic matter concentrated in oil-bearing structures after migration. No geological event remobilized the mineralizations since their settling [fr

  7. Optimisation Platform for copper ore processing at the Division of Concentrator of KGHM Polska Miedz S.A.

    Directory of Open Access Journals (Sweden)

    Kuzba Bogdan

    2016-01-01

    Full Text Available The idea of Optimisation Platform is to create an innovative system. It is dedicated to technology and cost efficiency improvement of process realized at the Division of Concentrators of KGHM Polska Miedz SA. This highly sophisticated tool is based on visual, acoustic and vibrating detection systems. The range of its functionality was described in this work. Three main utility modules were described: froth flotation image processing (FloVis, grinding and classification monitoring (MillVis and belt conveyors control unit (ConVis. The effects of implementation of the system under KGHM conditions were described. It is concluded that the Optimisation Platform is one of the most promising solution for improvement of technology and economy performance at the Division of Concentrators of KGHM Polska Miedz S.A.

  8. The determination, by x-ray-fluorescence spectrometry, of tin and tungsten in scheelite and cassiterite ores and concentrates

    International Nuclear Information System (INIS)

    Tolmay, R.T.; Jacobs, J.J.

    1980-01-01

    A method of analysis is presented that is applicable to sample mixtures of cassiterite and scheelite in concentrations of 0,2 to 70 per cent. Matrix variations are compensated for by dilution and fine grinding with coarse river sand, potassium chloride being used as a binder. Residual matrix effects are corrected for by the use of zinc and antimony as internal standards for tungsten and tin respectively. Calibration graphs are obtained by the use of chemically analysed scheelite and cassiterite standards. For tin, the relative standard deviation at a concentration of 60 per cent is 0,0063, and, at 10 per cent, 0,028; for tungsten, it is 0,013 at a concentration of 40 per cent. The lower levels of detection for tungsten and tin are 0,26 and 0,23 per cent respectively, and the time required for the analysis of 10 samples and 5 calibration standards by this method is 5 hours. A detailed laboratory method is given in the appendix [af

  9. Hydrothermal Alteration Mineral Mapping Using Sentinel-2A MSI and ASTER Data in the Duolong Ore Concentrating Area,Tibetau Plateau,China

    Science.gov (United States)

    Hu, B.; Wan, B.

    2017-12-01

    The porphyry copper deposits are characterized by alteration zones. Hydrothermal alteration minerals have diagnostic spectral absorption properties in the visible and near-infrared (VNIR) through the shortwave infrared (SWIR) regions. In order to identify the alteration zones in the study area, the Sentinel-2A Multi-Spectral Instrument(MSI) * Advanced Spaceborne Thermal Emission and Reflection Radiometer (ASTER) data and field inspection were combined. The Sentinel-2A MSI has ten bands in the visible and near-infrared (VNIR) regions, which has advantages of detecting ferric iron alteration minerals. Six ASTER bands in the shortwave infrared(SWIR) regions have been demonstrated to be effective in the mapping of Al-OH * Mg-OH group minerals. Integrating ASTER and Sentinel-2A MSI (AM) for mineral mapping can compensate each other's defect. The methods of minimum noise fraction(MNF) * band combination * matched filtering were applied to get Al-OH and Mg-OH group minerals information from AM data. The anomaly-overlaying selection method was used to process three temporal Sentinel-2A MSI data for extracting iron oxides minerals. The ground inspection has confirmed the validity of AM and Sentinel-2A MSI data in mineral mapping. The methodology proved effective in an arid area of Duolong ore concentrating area,Tibet and hereby suggested for application in similar geological settings.

  10. Leaching Kinetics of Praseodymium in Sulfuric Acid of Rare Earth Elements (REE) Slag Concentrated by Pyrometallurgy from Magnetite Ore

    International Nuclear Information System (INIS)

    Kim, Chul-Joo; Yoon, Ho-Sung; Chung, Kyung Woo; Lee, Jin-Young; Kim, Sung-Don; Shin, Shun Myung; Kim, Hyung-Seop; Cho, Jong-Tae; Kim, Ji-Hye; Lee, Eun-Ji; Lee, Se-Il; Yoo, Seung-Joon

    2015-01-01

    A leaching kinetics was conducted for the purpose of recovery of praseodymium in sulfuric acid (H 2 SO 4 ) from REE slag concentrated by the smelting reduction process in an arc furnace as a reactant. The concentration of H 2 SO 4 was fixed at an excess ratio under the condition of slurry density of 1.500 g slag/L, 0.3 mol H 2 SO 4 , and the effect of temperatures was investigated under the condition of 30 to 80 .deg. C. As a result, praseodymium oxide (Pr 6 O 1 1) existing in the slag was completely converted into praseodymium sulfate (Pr 2 (SO 4 ) 3 ·8H 2 O) after the leaching of 5 h. On the basis of the shrinking core model with a shape of sphere, the first leaching reaction was determined by chemical reaction mechanism. Generally, the solubility of pure REEs decreases with the increase of leaching temperatures in sulfuric acid, but REE slag was oppositely increased with increasing temperatures. It occurs because the ash layer included in the slag is affected as a resistance against the leaching. By using the Arrhenius expression, the apparent activation energy of the first chemical reaction was determined to be 9.195 kJmol -1 . In the second stage, the leaching rate is determined by the ash layer diffusion mechanism. The apparent activation energy of the second ash layer diffusion was determined to be 19.106 kJmol -1 . These relative low activation energy values were obtained by the existence of unreacted ash layer in the REE slag

  11. Leaching Kinetics of Praseodymium in Sulfuric Acid of Rare Earth Elements (REE) Slag Concentrated by Pyrometallurgy from Magnetite Ore

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Chul-Joo; Yoon, Ho-Sung; Chung, Kyung Woo; Lee, Jin-Young; Kim, Sung-Don; Shin, Shun Myung [Korea Institute of Geoscience and Mineral Resources, Daejeon (Korea, Republic of); Kim, Hyung-Seop; Cho, Jong-Tae; Kim, Ji-Hye; Lee, Eun-Ji; Lee, Se-Il; Yoo, Seung-Joon [Seonam University, Asan (Korea, Republic of)

    2015-02-15

    A leaching kinetics was conducted for the purpose of recovery of praseodymium in sulfuric acid (H{sub 2}SO{sub 4}) from REE slag concentrated by the smelting reduction process in an arc furnace as a reactant. The concentration of H{sub 2}SO{sub 4} was fixed at an excess ratio under the condition of slurry density of 1.500 g slag/L, 0.3 mol H{sub 2}SO{sub 4}, and the effect of temperatures was investigated under the condition of 30 to 80 .deg. C. As a result, praseodymium oxide (Pr{sub 6}O{sub 1}1) existing in the slag was completely converted into praseodymium sulfate (Pr{sub 2}(SO{sub 4}){sub 3}·8H{sub 2}O) after the leaching of 5 h. On the basis of the shrinking core model with a shape of sphere, the first leaching reaction was determined by chemical reaction mechanism. Generally, the solubility of pure REEs decreases with the increase of leaching temperatures in sulfuric acid, but REE slag was oppositely increased with increasing temperatures. It occurs because the ash layer included in the slag is affected as a resistance against the leaching. By using the Arrhenius expression, the apparent activation energy of the first chemical reaction was determined to be 9.195 kJmol{sup -1}. In the second stage, the leaching rate is determined by the ash layer diffusion mechanism. The apparent activation energy of the second ash layer diffusion was determined to be 19.106 kJmol{sup -1}. These relative low activation energy values were obtained by the existence of unreacted ash layer in the REE slag.

  12. Influence of acid/ore relation in the uranium-silicate ore treatment

    International Nuclear Information System (INIS)

    Antaki, C.; Cipriani, M.; Bruno, J.B.

    1985-01-01

    The estimation of acid addition effect (Kg of H 2 SO 4 /t of ore) in uranium extraction from an uranium-silicate ore, with a view to the control of silica concentration in leach under 0,6 g/l is presented. The analysis was effected based on bench-scale tests, with different quantities of sulfuric acid addition. (Author) [pt

  13. Uranium ore processing

    International Nuclear Information System (INIS)

    Ritcey, G.M.; Haque, K.E.; Lucas, B.H.; Skeaff, J.M.

    1983-01-01

    The authors have developed a complete method of recovering separately uranium, thorium and radium from impure solids such as ores, concentrates, calcines or tailings containing these metals. The technique involves leaching, in at least one stage. The impure solids in finely divided form with an aqueous leachant containing HCl and/or Cl 2 until acceptable amounts of uranium, thorium and radium are dissolved. Uranium is recovered from the solution by solvent extraction and precipitation. Thorium may also be recovered in the same manner. Radium may be recovered by at least one ion exchange, absorption and precipitation. This amount of iron in the solution must be controlled before the acid solution may be recycled for the leaching process. The calcine leached in the first step is prepared in a two stage roast in the presence of both Cl 2 and a metal sulfide. The first stage is at 350-450 0 and the second at 550-700 0

  14. A new approach for the high-precision determination of the elemental uranium concentration in uranium ore by gamma-ray spectrometry

    International Nuclear Information System (INIS)

    Nagel, W.; Quik, F.

    1993-01-01

    A new approach for the determination of elemental uranium in uranium bearing ore, using high resolution gamma-ray spectrometry, was applied. Using a variant of the enrichment meter technique an agreement of better than 1% has been obtained between gamma-ray measurement results and the certified value obtained by other analytical methods. For the calibration of the gamma-ray spectrometer uranium reference samples have been used which are made available jointly in Europe and the USA as Certified Reference Materials for Gamma-ray Spectrometry (EC NRM 171 and NBS SRM 969, respectively). The measured ore has been put in a special designed container which ensured in all directions seen from the radiation window a uniform degree of infinite thickness of about 95%. The measurement results can be taken as an example for the applicability of gamma-ray spectrometry when high accuracy is required and under conditions where homogeneous distributed elemental uranium is embedded in a larger amount of matrix material. (author). 8 refs., 10 figs., 2 tabs., 2 appendices

  15. Assessment of the effect of innovation on the costs of a uranium ore concentration plant by means of a technical and economic model. Examples of applications: direct precipitation of the peroxide UO4 xH2O high temperature and high concentration alkaline treatment

    International Nuclear Information System (INIS)

    Boutonnet, G.; Roullier, J.P.

    1983-01-01

    Uranium Pechiney Ugine Kuhlmann has developed an economic model for uranium ore treatment plants. In this model, the basic economic data for a given plant, such as capital expenditures, operating costs, etc. are derived from parameters based partly on the size of the plant and the production progamme considered, and partly on the cost and specifications of the ore to be treated. In addition to numerous macro-economic applications (not considered here), the model can be used for making coherent comparisons of the economy of a plant designed for an innovative production process with that of the same plant designed for a conventional process of acid treatment followed by solvent extraction. The model shows that two new processes are highly competitive with the conventional process. They are: 1. Direct precipitation of the peroxide UO 4 xH 2 O in the pregnant liquor without concentration or purification by solvents or exchangers, and 2. High temperature and high concentration alkaline treatment

  16. Separation of monazite from Rirang ore by floatation method

    International Nuclear Information System (INIS)

    Affandi, Kosim; Sjahminan, Mainar

    1995-01-01

    Separation of monazite from Rirang ore has been carried out by means of floatation using oleic acid and pine oil as promoter and frothier reagents, respectively. Several parameters affecting floatation process, i.e. grain size of the ore, pulp pH, and reagents concentration were examnined. The optimal conditions for the process include the use of -100 mesh feed ore, pulp pH 9.0 and 1 kilogram of each oleic acid and pine oil per tonne ore. Based on the conditions, monazite recovery of 90% was achieved with about 20% uranium remain in monazite concentrate. (author). 7 refs, 9tabs, 1 fig

  17. Testing of X-ray radiometric enrichnment of polymetallic ores

    International Nuclear Information System (INIS)

    Eliseev, N.I.; Panova, N.I.; Kirbitova, N.V.; Shramm, E.O.; Efremov, Yu.G.

    1987-01-01

    Testing of X-ray radiometric method of sorting of polymetallic ores using the developed X-ray radiometric device was conducted. It was shown that introduction of preliminary concentration at the factory made the method of fragment separation to be the perspective one, enabling to elevate the factory production with respect to commercial ore and reduce the cost of ore processing. In the case of preliminary concentration, conducted at the mine, it is advisable to perform ore sorting in the flow formed to monolayer

  18. Uranium recovery from phosphate rocks concentrated

    International Nuclear Information System (INIS)

    Azevedo, M.F. de.

    1986-01-01

    The reserves, geological data, chemical data and technical flowsheet from COPEBRAS and Goiasfertil ores are described, including the process of mining ore concentration. Samples of Goiasfertil ores are analysed by gravimetric analysis, for phosphate, and spectrofluorimetry for uranium. (author)

  19. Radon risk in ore miners

    International Nuclear Information System (INIS)

    Beno, M.

    1997-01-01

    Underground workers are exposed to various clastogenic agents. One of these agents, radon, attracts attention of recent research as it causes lung cancer in the population occupationally exposed to its various concentrations especially in mine air of uranium mines or ore mines. This paper is a pilot study in which the numbers of chromosomal aberrations (CA) in lymphocytes of ore mines (Nizna Slana-iron ore, Hnusta-talc ore) located in east central Slovakia were followed and related to the lifetime underground radon exposure and to lifetime smoking. Seventy miners volunteering after an informed consent served as donors of venous blood. Twenty healthy pro-bands, age matched with the miners, which never worked underground (mostly clerks) served as donors of control blood samples. The exposure to radon and smoking has been estimated according to working-records and personal anamnesis. The findings unequivocally showed a small but statistically significant clastogenic effect of the exposure to underground environment of the mines concerned. This study has shown also a small but significant influence of smoking, which in the subgroup of miners working underground less than 1500 shifts may have acted synergically with the underground exposure. It was concluded tat: (1) Significantly higher counts of chromosomal aberrations in lymphocytes of 70 miners than in an age matched control group of 20 white-collar workers were found; (2) The higher counts of chromosomal aberrations could be ascribed to underground exposure of miners and to smoking; (3) The positive dependence of the number of chromosomal aberrations from the exposure to smoking was loose and it was expressed by significantly higher chromosomal aberrations counts in the group of miners working less than 1500 shifts underground; (4) A dependence of chromosomal aberrations counts from the exposure to radon could not be assessed. At relatively low numbers of pro-bands in subgroups it was not ruled out the confounding

  20. Technology development for recovery of individual rare earth elements at high purity from Dong-Pao rare earth concentrated ore of Vietnam

    International Nuclear Information System (INIS)

    Hoang Nhuan; Le Ba Thuan; Luu Xuan Dinh; Tran Hoang Mai; Tran Thi Hong Thai; Yoshiuyki Aiba; Hiroaki Nishimura

    2015-01-01

    In this work, the research results on RE processing process at laboratory scale and pilot scale was reported and discussed. Experimental research on thermal decomposition and sulfate process of bastnaesite ore with sulfuric acid in electric furnace was carried out, the different roasting conditions, mass transfer rate, reactions and RE and/or non-RE behaviors during roasting and leaching were investigated. The roasting temperatures were 450"oC and 550"oC. With higher roasting temperature and longer roasting time, the RE recovery yield reduced. The RE recovery yield reached the highest (over 94%) at roasting temperature of 550"oC for 2 hrs. The different extracting conditions for separation of REEs were investigated in laboratory scale as well as pilot scale. At pilot scale, the separation of REEs was performed on 120-stage extraction system produced by Japan, using PC88A solvent dissolved in IP2028. The volume of each stage was 20 L. The results showed that REEs were separated from RE resource of Vietnam and individual RE elements such as La, Ce, Pr, and Nd were obtained at high purity. The parameters for each extraction stage were reported in this work. The results indicated that in order to obtain highly purified Nd (>99%), it needs to use an extraction system with higher stage number, about 200 stages. The extraction data at pilot scale of this investigation was used as basic data for calculating parameters for extraction system in industrial scale. (author)

  1. Hydrogen Reduction of Hematite Ore Fines to Magnetite Ore Fines at Low Temperatures

    Directory of Open Access Journals (Sweden)

    Wenguang Du

    2017-01-01

    Full Text Available Surplus coke oven gases (COGs and low grade hematite ores are abundant in Shanxi, China. Our group proposes a new process that could simultaneously enrich CH4 from COG and produce separated magnetite from low grade hematite. In this work, low-temperature hydrogen reduction of hematite ore fines was performed in a fixed-bed reactor with a stirring apparatus, and a laboratory Davis magnetic tube was used for the magnetic separation of the resulting magnetite ore fines. The properties of the raw hematite ore, reduced products, and magnetic concentrate were analyzed and characterized by a chemical analysis method, X-ray diffraction, optical microscopy, and scanning electron microscopy. The experimental results indicated that, at temperatures lower than 400°C, the rate of reduction of the hematite ore fines was controlled by the interfacial reaction on the core surface. However, at temperatures higher than 450°C, the reaction was controlled by product layer diffusion. With increasing reduction temperature, the average utilization of hydrogen initially increased and tended to a constant value thereafter. The conversion of Fe2O3 in the hematite ore played an important role in the total iron recovery and grade of the concentrate. The grade of the concentrate decreased, whereas the total iron recovery increased with the increasing Fe2O3 conversion.

  2. The geological characteristics and forming conditions of granite type uranium-rich ore deposits

    International Nuclear Information System (INIS)

    Li Tiangang; Tong Hangshou; Feng Mingyue; Li Yuexiang; Xu Zhan

    1993-03-01

    The forming conditions and concentration mechanism of rich ore, criteria of ore prospecting and selection of uranium-rich ore target area are introduced in the article that is based on the studying of geological characteristics and conditions of granite type uranium-rich ore deposits of No 201 and 361 and on the comparisons of rich and poor ore deposits in geological conditions. Some new view points are also presented as the separate deposition of uranium minerals and gangue minerals is the main mechanism to form rich ore, for rich ore formation the ore enrichment by superimposition is not a universal regularity and most uranium-rich ore deposits are formed within one mineralization stage or mainly in one mineralization stage

  3. The geological characteristics and forming conditions of granite type uranium-rich ore deposits

    Energy Technology Data Exchange (ETDEWEB)

    Tiangang, Li; Hangshou, Tong; Mingyue, Feng; Yuexiang, Li; Zhan, Xu [Beijing Research Inst. of Uranium Geology (China)

    1993-03-01

    The forming conditions and concentration mechanism of rich ore, criteria of ore prospecting and selection of uranium-rich ore target area are introduced in the article that is based on the studying of geological characteristics and conditions of granite type uranium-rich ore deposits of No 201 and 361 and on the comparisons of rich and poor ore deposits in geological conditions. Some new view points are also presented as the separate deposition of uranium minerals and gangue minerals is the main mechanism to form rich ore, for rich ore formation the ore enrichment by superimposition is not a universal regularity and most uranium-rich ore deposits are formed within one mineralization stage or mainly in one mineralization stage.

  4. Improvements on heap leaching process for a refractory uranium ore and yellow cake precipitation process

    International Nuclear Information System (INIS)

    Feng Jianke

    2013-01-01

    Some problems such as formed harden matrix, ore heap compaction, poor permeability, and agglomeration of absorption resin occur during extracting uranium from a refractory uranium ore by heap leaching process. After some measures were taken, i.e. spraying a new ore heap by low concentration acid, two or more ore heaps in series leaching, turning ores in ore heap, the permeability was improved, acid consumption was reduced. Through precipitate circulation and aging, the yellow cake slurry in amorphous or microlite form was transformed to crystal precipitate, thus uranium content in yellow cake was improved, and water content in yellow cake was lowered with good economic benefits. (author)

  5. Sampling of ore

    International Nuclear Information System (INIS)

    Boehme, R.C.; Nicholas, B.L.

    1987-01-01

    This invention relates to a method of an apparatus for ore sampling. The method includes the steps of periodically removing a sample of the output material of a sorting machine, weighing each sample so that each is of the same weight, measuring a characteristic such as the radioactivity, magnetivity or the like of each sample, subjecting at least an equal portion of each sample to chemical analysis to determine the mineral content of the sample and comparing the characteristic measurement with desired mineral content of the chemically analysed portion of the sample to determine the characteristic/mineral ratio of the sample. The apparatus includes an ore sample collector, a deflector for deflecting a sample of ore particles from the output of an ore sorter into the collector and means for moving the deflector from a first position in which it is clear of the particle path from the sorter to a second position in which it is in the particle path at predetermined time intervals and for predetermined time periods to deflect the sample particles into the collector. The apparatus conveniently includes an ore crusher for comminuting the sample particle, a sample hopper means for weighing the hopper, a detector in the hopper for measuring a characteristic such as radioactivity, magnetivity or the like of particles in the hopper, a discharge outlet from the hopper and means for feeding the particles from the collector to the crusher and then to the hopper

  6. Introduction to ore geology

    International Nuclear Information System (INIS)

    Evans, A.M.

    1987-01-01

    This textbook on ore geology is for second and third year undergraduates and closely parallels the undergraduate course given in this subject at England's University of Leicester. The volume covers three major areas: (1) principles of ore geology, (2) examples of the most important types of ore deposits, and (3) mineralization in space and time. Many chapters have been thoroughly revised for this edition and a chapter on diamonds has been added. Chapters on greisen and pegmatite have also been added, the former in response to the changing situation in tin mining following the recent tin crisis, and the latter in response to suggestions from geologists in a number of overseas countries. Some chapters have been considerably expanded and new sections added, including disseminated gold deposits and unconformity-associated uranium deposits. The author also expands on the importance of viewing mineral deposits from an economic standpoint

  7. Uranium abundance in some sudanese phosphate ores

    International Nuclear Information System (INIS)

    Adam, A.A.; Eltayeb, M.A.H.

    2009-01-01

    This work was carried out mainly to analysis of some Sudanese phosphate ores, for their uranium abundance and total phosphorus content measured as P 2 O 5 %. For this purpose, 30 samples of two types of phosphate ore from Eastern Nuba Mountains, in Sudan namely, Kurun and Uro areas were examined. In addition, the relationship between uranium and major, and trace elements were obtained, also, the natural radioactivity of the phosphate samples was measured, in order to characterize and differentiate between the two types of phosphate ores. The uranium abundance in Uro phosphate with 20.3% P 2 O 5 is five time higher than in Kurun phosphate with 26.7% P 2 O 5 . The average of uranium content was found to be 56.6 and 310 mg/kg for Kurun and Uro phosphate ore, respectively. The main elements in Kurun and Uro phosphate ore are silicon, aluminum, and phosphorus, while the most abundant trace elements in these two ores are titanium, strontium and barium. Pearson correlation coefficient revealed that uranium in Kurun phosphate shows strong positive correlation with P 2 O 5 , and its distribution is essentially controlled by the variations of P2O5 concentration, whereas uranium in Uro phosphate shows strong positive correlation with strontium, and its distribution is controlled by the variations of Sr concentration. Uranium behaves in different ways in Kurun phosphate and in Uro phosphate. Uro phosphate shows higher concentrations of all the estimated radionuclides than Kurun phosphate. According to the obtained results, it can be concluded that Uro phosphate is consider as secondary uranium source, and is more suitable for uranium recovery, because it has high uranium abundance and low P 2 O 5 %, than Kurun phosphate. (authors) [es

  8. Chapter 1. The characteristics of borosilicate ores of Ak-Arkhar Deposit of Tajikistan

    International Nuclear Information System (INIS)

    Mirsaidov, U.M.; Kurbonov, A.S.; Mamatov, E.D.

    2015-01-01

    Present article is devoted to characteristics of borosilicate ores of Ak-Arkhar Deposit of Tajikistan. The chemical composition of danburite ore of Ak-Arkhar Deposit was defined. The chemical composition of danburite ore concentrate of Ak-Arkhar Deposit was defined as well.

  9. Chemical treatment of uranium ores in France

    International Nuclear Information System (INIS)

    Mouret, P.; Sartorius, R.

    1958-01-01

    The various processes of chemical treatment of uranium ores, from the oldest to the more recent, are exposed, considering the following conditions: economics, geography, techniques and safety. The interest of obtaining a final concentrate as uranyl nitrate is discussed. (author) [fr

  10. Hydrometallurgical Processing Technology of Titanomagnetite Ores

    Directory of Open Access Journals (Sweden)

    Victor Ivanovich Sachkov

    2017-12-01

    Full Text Available In this paper, we study the possibility of obtaining iron and titanium-vanadium concentrates with highest contents of iron and titanium, respectively, through hydrometallurgical processing of the titanomagnetite ores of the Chineisk deposit. We varied two key parameters to determine the efficiency of the process: (a concentration of leaching solution (ammonium fluoride; and (b acidity of solution. Ammonium fluoride concentration was varied from 0.08 mol/L to 4.2 mol/L with the other fixed parameters. It was shown that optimum ammonium fluoride concentration for leaching the ore is 0.42 mol/L; at these concentrations iron and titanium contents are about 62.8 wt % and 3.5 wt % in solid phase, respectively. The acidity of solution was changed by adding of hydrofluoric acid with varied concentration (from 0.86 mol/L to 4.07 mol/L to ammonium fluoride solution with fixed concentration of 0.42 mol/L. The best results (degree of titanium extraction = 63.7% were obtained when using a solution of hydrofluoric acid with concentration 4.07 mol/L. In this case, the addition of acid makes it possible to increase the Fe/Ti ratio by 3.4 times in comparison with the original ore. Thus, we conclude that acidity and the concentration of ammonium fluoride solution significantly influences the selectivity of the hydrometallurgical process.

  11. Environmental nuclear-geophysical ore monitoring in mines of Corporation Kazakhmys PLC.

    Science.gov (United States)

    Yefimenko, Sergei; Yefimenko, Olga; Makarov, Dmitriy

    2014-01-01

    An environmental monitoring of ore composition in complex deposits of Kazakhstan (the Zhezkazgan, Kusmuryn, Artemjevsk, Kounrad, Taskura and Zhaman-Aibat deposits) is carried out using EDXRF spectrometers RPP-12, RLP-21 and RLP-21T. The monitoring of ore concentrates in Satpaev, Balkhashsk and Zhezkazgan processing plants and in Zhezkazgan copper smelter continues at present time. The monitoring suggests data on new promising elements and environmental pollutants in ores and new trends in distribution of bound elements in ores.

  12. Uranium accompanying recovery from copper ores

    International Nuclear Information System (INIS)

    Golynko, Z.Sh.; Laskorin, B.N.

    1981-01-01

    In the search for new raw material sources for nuclear power engineering a review of the technique of uranium accompaning recovery from copper ores reprocessing products in some countries is presented. In the USA a sorption method of uranium extraction by means of strongly basic ion exchange resins from solutions upon copper case- hardening with subsequent extraction from eluates by solutions of tertiary amines is realized. Elution is realized with sulphuric acid. In South Africa an extraction reprocessing of gravitational concentrate extracted from copper sulphide flotation tailings is organized. In India the uranium extraction from copper ores flotation enrichment tailings is organized on a commerical scale. Presented are data on the scale of uranium recovery, various conditions of its recovery as well as block diagrams of the processes. It is shown that copper ores become an additional source of uranium recovery [ru

  13. Fission track method for uranium ore exploration

    International Nuclear Information System (INIS)

    Guo Shilun; Deng Xinlu; Sun Shengfen; Meng Wu; Zhang Pengfa; Hao Xiuhong

    1986-01-01

    The uranium concentrations in natural water collected in the fields of uranium ore exploration with fission track method have been determined. It shows that the results of fission track method are consistent with that of fluoro-colorimetry and laser fluorometry for the same samples of water with uranium concentration in the region of 10 -4 to 10 -8 g/l. For water samples with lower uranium concentration (≤10 -8 g/l), the fission track method can still give accurate or referential results, but the other two methods failed. The reproducibility of fission track method was checked and discussed by using samples collected in the same fields of uranium ore exploration. The effects of the concentration of the impurities in natural water on determination of uranium concentration were analysed and discussed as well

  14. Water leaching of titanium from ore flotation residue.

    Science.gov (United States)

    Jaworska, Malgorzata M; Guibal, Eric

    2003-01-01

    Copper ore tailings were tested for the stability of titanium submitted to water leaching in three different reactor systems (agitated vessel, bioreactor and percolated fixed-bed column). For each of these systems, titanium extraction did not exceed 1% of the available metal. Biomass removed from ore residue adsorbed a small part of the titanium with sorption capacities below 20-30 mg g(-1), but most of this biomass was sequestered in the ore residue. Oxygen and carbon dioxide concentrations were monitored and changes in concentration correlated with bacteria development at the initial stage of the process and to fungal development in the latter stages.

  15. The determination, by X-ray-fluorescence spectrometry, of tin and tungsten in ores, concentrates, and residues of scheelite, wolframite, and cassiterite

    International Nuclear Information System (INIS)

    Balaes, A.M.E.; Jacobs, J.J.; Bray, A.R.; Kendrick, K.

    1983-01-01

    The method of analysis described is applicable to samples with tin and tungsten contents from 15p.p.m. to 75 per cent. For samples containing tin and tungsten in the range 2000p.p.m. to 75 per cent, the matrix variations are compensated for by the use of briquettes containing coarse river sand, the internal standard, and potassium chloride, the last of which acts as a binder, diluet, and grinding aid. For the samples containing tin and tungsten in the range 15p.p.m. to 2000p.p.m., the potassium chloride is omitted. Zinc and antimony are used as the internal standard for tungsten and tin respectively. Calibration graphs for tin and tungsten are obtained by the use of standard reference materials for cassiterite and scheelite. The precision of the analysis for tin ranges from a relative standard deviation of 0,039 at 50p.p.m. to 0,005 at 75 per cent. The values for tungsten are relatively constant at between 0,015 and 0,008 at concentrations between 50p.p.m. and 50 per cent. The lower limits of detection for tungsten and tin by the high-concentration technique of analysis are 202 and 155p.p.m. respectively, and by the low-concentration technique the corresponding limits are 4 and 2p.p.m. The overall time required for the analysis of ten samples by these techniques is approximately 3 hours. The laboratory method is detailed in an appendix

  16. The determination, by x-ray spectrometry, of trace amounts of tin in titanium-bearing ores and concentrates and in siliceous materials

    International Nuclear Information System (INIS)

    Jacobs, J.J.; Balaes, A.M.E.

    1980-01-01

    The method involves the preparation of briquettes, one of which consists of the sample material and an inert diluent, the other of the sample material and a standard reference material. After the briquettes have been analysed, a correction is made for the background of the matrix, which is based on the intensity function, (peak - background)/background. No calibration graph is required. The lower level of detection of the method is 10 p.p.m., and the relative standard deviation is 0,1 at a tin concentration of 100 p.p.m. A computer programme for the off-line processing of intensity data is listed in an appendix

  17. Geochemistry and ore prospecting

    International Nuclear Information System (INIS)

    Le Caignec, R.

    1954-01-01

    Applied geochemistry is a new technique which helps the geologist in detecting ore deposits. Some deposits, even when they are covered with rather thick surface structures, form around these zones where the infinitesimal content of some elements of soils or waters is notably different. These 'anomalies' may be contemporaneous to the deposit-structure (primary dispersion) or may have occurred later (secondary dispersion). Various factors rule these anomalies: ore-stability, soil homogeneity, water conditions, topography, vegetation, etc... Applied geochemistry is in fact the study of analysis techniques of metal traces in soils as well as the geological interpretation of observed anomalies. This report gives practical data on sampling methods, yields, costs and also on special problems of uranium geochemistry. (author) [fr

  18. Beneficiation studies of Bajaur manganese ore by different processing techniques

    International Nuclear Information System (INIS)

    Riaz, M.; Khan, F.U.; Yamin, A.; Bilquees, R.; Muhammad, N.

    2010-01-01

    The manganese ore of Bajaur Agency of Pakistan was subjected to flotation, heavy medium separation, gravity concentration and magnetic separation techniques for beneficiation. The original composition of the manganese ore was 45.56% Mn , 4% Fe/sub 2/O/sub 3/, 40% SiO/sub 2/. The Mn content was raised to a maximum 48.76 % in the concentrate with the recovery of 67.78 % through flotation technique. Other techniques rendered marginal increase in Mn concentration against the theoretical possibility of substantial enrichment by rejecting the 20 % gangue minerals. The separation of manganese minerals from associated gangue was difficult, due to mineralogical complexity of the ore, extreme fineness of the particle size, texture and minerals intergrowth. High Mn/Fe ratio, phosphorus, and silica contents were within tolerable limits for utilisation of the ore in ferro-manganese production. (author)

  19. Computer finds ore

    Science.gov (United States)

    Bell, Peter M.

    Artificial intelligence techniques are being used for the first time to evaluate geophysical, geochemical, and geologic data and theory in order to locate ore deposits. After several years of development, an intelligent computer code has been formulated and applied to the Mount Tolman area in Washington state. In a project funded by the United States Geological Survey and the National Science Foundation a set of computer programs, under the general title Prospector, was used successfully to locate a previously unknown ore-grade porphyry molybdenum deposit in the vicinity of Mount Tolman (Science, Sept. 3, 1982).The general area of the deposit had been known to contain exposures of porphyry mineralization. Between 1964 and 1978, exploration surveys had been run by the Bear Creek Mining Company, and later exploration was done in the area by the Amax Corporation. Some of the geophysical data and geochemical and other prospecting surveys were incorporated into the programs, and mine exploration specialists contributed to a set of rules for Prospector. The rules were encoded as ‘inference networks’ to form the ‘expert system’ on which the artificial intelligence codes were based. The molybdenum ore deposit discovered by the test is large, located subsurface, and has an areal extent of more than 18 km2.

  20. O-Ring sealing arrangements for ultra-high vacuum systems

    Science.gov (United States)

    Kim, Chang-Kyo; Flaherty, Robert

    1981-01-01

    An all metal reusable O-ring sealing arrangement for sealing two concentric tubes in an ultra-high vacuum system. An O-ring of a heat recoverable alloy such as Nitinol is concentrically positioned between protruding sealing rings of the concentric tubes. The O-ring is installed between the tubes while in a stressed martensitic state and is made to undergo a thermally induced transformation to an austenitic state. During the transformation the O-ring expands outwardly and contracts inwardly toward a previously sized austenitic configuration, thereby sealing against the protruding sealing rings of the concentric tubes.

  1. Fundamentals of fast reduction of ultrafine iron ore at low temperature

    Institute of Scientific and Technical Information of China (English)

    Pei Zhao; Peimin Guo

    2008-01-01

    Fundamentals on the fast reduction of ultrafine iron ore at low temperature, including characterization of ultrafine ore, de- oxidation thermodynamics of stored-energy ultrafine ore, kinetics of iron ore deoxidation, and deoxidation mechanism, etc., and a new ironmaking process are presented in this article. Ultrafine ore concentrate with a high amount of stored energy can be produced by mechanical milling, and can be dcoxidated fast below 700℃ by either the coal-based or gas-based process. This novel process has some advantages over others: high productivity, low energy consumption, and environmental friendliness.

  2. Studies on uranium ore processing

    International Nuclear Information System (INIS)

    Kim, C.H.; Park, S.W.; Lim, J.K.; Chung, M.K.

    1981-01-01

    Chemical and chemical engineering techniques of the uranium ore processing established by France COGEMA (Compagnie Generale des Matieres Nucleaires) have been comprehensively reviewed in preparation for successful test operation of the pilot plant to be completed by the end of 1981. It was found that the amount of sulfuric acid (75 Kg/t, ore) and sodium chlorate (2.5 Kg/t, ore) recommended by COGEMA should be increased up to 100 Kg/t, ore and 10 Kg/t, ore respectively to obtain satisfactory leach of uranium for some ore samples produced at the different pits of Goesan uranium mine. Conditions of the other processes such as solvent extraction, stripping, and precipitation of yellow cake were generally agreed with the results of intensive studies done by this laboratory

  3. Bacterial leaching of pyritic gold ores

    International Nuclear Information System (INIS)

    Gagliardi, F.M.; Cashion, J.D.; Brown, J.; Jay, W.H.

    1998-01-01

    Full text: Pyritic ores (pyrite and arsenopyrite) containing gold concentrations in excess of 50g Au/t can be processed to recover the gold by the removal of the sulphur from the ore. This may be achieved by roasting (producing sulphur dioxide emissions), pressure oxidation (expensive and suitable for large high grade deposits), pressure leaching (still currently being developed) or bacterial oxidation. The bacterial oxidation process is a well known process in nature but has only recently come under investigation as a economically viable and relatively clean method of gold recovery from deep low grade sulphidic ores. Samples were obtained from the Wiluna Gold Mine in Western Australia consisting of the original ore, six successive bacterial reactors and the final products. Moessbauer experiments have been performed at room temperature, liquid nitrogen and liquid helium temperatures, and in applied magnetic fields. The main components of the iron phases which were present during the bacterial treatment were pyrite and arsenopyrite which were readily oxidised by the bacteria. Ferric sulfates and ferric arsenates were identified as by-products of the process with a small amount of the oxyhydroxide goethite. These results are in contrast to the similar study of the Fairview Mine in South Africa where principally Fe(II) species were observed

  4. Complexing and hydrothermal ore deposition

    CERN Document Server

    Helgeson, Harold C

    1964-01-01

    Complexing and Hydrothermal Ore Deposition provides a synthesis of fact, theory, and interpretative speculation on hydrothermal ore-forming solutions. This book summarizes information and theory of the internal chemistry of aqueous electrolyte solutions accumulated in previous years. The scope of the discussion is limited to those aspects of particular interest to the geologist working on the problem of hydrothermal ore genesis. Wherever feasible, fundamental principles are reviewed. Portions of this text are devoted to calculations of specific hydrothermal equilibriums in multicompone

  5. Zeolitization at uranium ore manifestation

    International Nuclear Information System (INIS)

    Petrosyan, R.V.; Buntikova, A.F.

    1981-01-01

    The process of zeolitization at uranium ore manifestation is studied. A specific type of low-temperature wall endogenous alteration of rocks due to the effect of primary acid solution with low content of carbonic acid is established. Leaching of calcium from enclosing rocks and its deposition in ore-accompanying calcium zeolites is a characteristic feature of wall-metasomatosis. Formation of desmin- calcite-laumontite and quartz-fluoroapatite of vein associations, including ore minerals (uranophane and metaotenite), is genetically connected with calcium metasomatosis. On the basis of the connection of ore minerals with endogeneous process of zeolitization a conclusion can be made on endogenous origin of uranophane and metaotenite [ru

  6. Collective sulphide flotation of the polymetallic molybdenic ore

    International Nuclear Information System (INIS)

    Mazanek, C.; Maselko, J.; Rycerz, L.

    1980-01-01

    Results of investigations on polymetallic molybdenic ore are presented. The useful minerals of this ore are as follows: molybdenite, sphalerite, galena and chalcopyrite whereas quartz, feldspars, chlorite and sericite are barren rocks. The flotation process parameters are established i.e. the consumption of flotation reagents, the flotation time and the most advantageous grain composition of the ore submitted to flotation. Taking into consideration the established parameters, a collective sulphide flotation of ore and a control flotation of wastes were carried out. The obtained concentrate was submitted to a single cleaning flotation whereby a concentrate was obtained containing: 4,65% Mo, 2,51% Cu, 0,9% Zn, 0,69% Pb, and 1,4% Bi. (author)

  7. Beneficiation of the gold bearing ore by gravity and flotation

    Science.gov (United States)

    Gül, Alim; Kangal, Olgaç; Sirkeci, Ayhan A.; Önal, Güven

    2012-02-01

    Gold concentration usually consists of gravity separation, flotation, cyanidation, or the combination of these processes. The choice among these processes depends on the mineralogical characterization and gold content of the ore. Recently, the recovery of gold using gravity methods has gained attention because of low cost and environmentally friendly operations. In this study, gold pre-concentrates were produced by the stepwise gravity separation and flotation techniques. The Knelson concentrator and conventional flotation were employed for the recovery of gold. Gold bearing ore samples were taken from Gümüşhane Region, northern east part of Turkey. As a result of stepwise Knelson concentration experiments, a gold concentrate assaying around 620 g/t is produced with 41.4wt% recovery. On the other hand, a gold concentrate about 82 g/t is obtained with 89.9wt% recovery from a gold ore assaying 6 g/t Au by direct flotation.

  8. A comparison of portable XRF and ICP-OES analysis for lead on air filter samples from a lead ore concentrator mill and a lead-acid battery recycler.

    Science.gov (United States)

    Harper, Martin; Pacolay, Bruce; Hintz, Patrick; Andrew, Michael E

    2006-03-01

    Personal and area samples for airborne lead were taken at a lead mine concentrator mill, and at a lead-acid battery recycler. Lead is mined as its sulfidic ore, galena, which is often associated with zinc and silver. The ore typically is concentrated, and partially separated, on site by crushing and differential froth flotation of the ore minerals before being sent to a primary smelter. Besides lead, zinc and iron are also present in the airborne dusts, together with insignificant levels of copper and silver, and, in one area, manganese. The disposal of used lead-acid batteries presents environmental issues, and is also a waste of recoverable materials. Recycling operations allow for the recovery of lead, which can then be sold back to battery manufacturers to form a closed loop. At the recycling facility lead is the chief airborne metal, together with minor antimony and tin, but several other metals are generally present in much smaller quantities, including copper, chromium, manganese and cadmium. Samplers used in these studies included the closed-face 37 mm filter cassette (the current US standard method for lead sampling), the 37 mm GSP or "cone" sampler, the 25 mm Institute of Occupational Medicine (IOM) inhalable sampler, the 25 mm Button sampler, and the open-face 25 mm cassette. Mixed cellulose-ester filters were used in all samplers. The filters were analyzed after sampling for their content of the various metals, particularly lead, that could be analyzed by the specific portable X-ray fluorescence (XRF) analyzer under study, and then were extracted with acid and analyzed by inductively coupled plasma optical emission spectroscopy (ICP-OES). The 25 mm filters were analyzed using a single XRF reading, while three readings on different parts of the filter were taken from the 37 mm filters. For lead at the mine concentrate mill, all five samplers gave good correlations (r2 > 0.96) between the two analytical methods over the entire range of found lead mass

  9. Uranium ore deposits

    International Nuclear Information System (INIS)

    Angelelli, Victorio.

    1984-01-01

    The main uranium deposits and occurrences in the Argentine Republic are described, considering, in principle, their geologic setting, the kind of 'model' of the mineralization and its possible origin, and describing the ore species present in each case. The main uraniferous accumulations of the country include the models of 'sandstong type', veintype and impregnation type. There are also other kinds of accumulations, as in calcrete, etc. The main uranium production has been registered in the provinces of Mendoza, Salta, La Rioja, Chubut, Cordoba and San Luis. In each case, the minerals present are mentioned, having been recognized 37 different species all over the country (M.E.L.) [es

  10. Niobium ore OKA-1

    International Nuclear Information System (INIS)

    Steger, H.F.; Bowman, W.S.

    1981-01-01

    A 287-kg sample of a niobium ore, OKA-1, from Oka, Quebec, was prepared as a compositional reference material. OKA-1 was ground to minus 74 μm, blended in one lot, tested for homogeneity by X-ray fluorescence and chemical methods and bottled in 200-g units. In a 'free-choice' round-robin analytical program, 22 laboratories contributed results for niobium in each of two bottles of OKA-1. A statistical analysis of the data gave a recommended value of 0.37 +- 0.01% for niobium

  11. Extraction of lithium Carbonate from Petalite Ore (Momeik District, Myanmar)

    International Nuclear Information System (INIS)

    Tun Tun Moe

    2011-12-01

    The methods for preparing high purity lithium carbonate which can be used for pharmaceutical applications, electronic grade crystals of lithium or to prepare battery-grade lithium metal are disclosed. Lithium carbonate as commercially produced from mineral extraction, lithium containing brines or sea water. One method for the production of pure lithium carbonate from mineral source (petalite ore) obtained from Momeik District, Myanmar is disclosed. Method for mineral processing of ore concentrate is also disclosed.

  12. Uranium ore processing in Spain

    International Nuclear Information System (INIS)

    Josa, J.M.

    1976-01-01

    The paper presents a review of the Spanish needs of uranium concentrates and uranium ore processing technology and trends in Spain. Spain produces approximately 200t U 3 O 8 /a at two facilities. One plant in the south (Andujar, Jaen) can obtain 70t U 3 O 8 /a and uses a conventional acid leaching process with countercurrent solvent extraction. A second plant, situated in the west (Ciudad Rodrigo, Salamanca) has started in 1975 and has a capacity of 120-130t U 3 O 8 /a, using acid heap leaching and solvent extraction. There is another experimental facility (Don Benito, Badajoz) scheduled to start in 1976 and expected to produce about 25-35t U 3 O 8 /a as a by-product of the research work. For the near future (1978) it is hoped to increase the production with: (a) A new conventional acid leaching/solvent extraction plant in Ciudad Rodrigo; its tentative capacity is fixed at 550t U 3 O 8 /a. (b) A facility in the south, to recover about 130t U 3 O 8 /a from phosphoric acid. (c) Several small mobile plants (30t U 3 O 8 /a per plant); these will be placed near small and isolated mines. The next production increase (1979-1980) will come with the treatment of sandstones (Guadalajara and Cataluna) and lignites(Cataluna); this is being studied. There are also research programmes to study the recovery of uranium from low-grade ores (heap, in-situ and bacterial leaching) and from other industries. (author)

  13. Behaviour of the pH adjustment, Ion exchange and concentrate precipitation stages in the acid leaching of uranium phosphate ores; Tratamiento de disoluciones de lixiviacion de minerales de uranio en presencia de fosfatos. Comportamiento en las etapas de ajuste de PH, cambio de ion y precipitacion de concentrados

    Energy Technology Data Exchange (ETDEWEB)

    Estrada Aguilar, J; Uriarte Hueda, A

    1962-07-01

    The uranium recovery from acid leach solutions of uranium-phosphate ores has been studied. Relations have been found between the solution characteristics and the results obtained at different stages of the process. The following data can thus be predicted: solids to remove and uranium recovery in the pH adjustment stage, uranium capacity of the resin, more suitable eluating agent, elution velocity and uranium concentration in the eluate in the ion exchange stage, and composition of the concentrate produced by direct precipitation of the eluate in the concentrate precipitation stage. (Author) 8 refs.

  14. The treatment of uranium ores

    International Nuclear Information System (INIS)

    Michel, P.

    1979-01-01

    After having described the main steps in the treatment of uranium ores, the author describes the treament activities for these ores, as they are organized in France and in the African countries having made cooperation agreements with France in this field [fr

  15. Dose calculations for intakes of ore dust

    International Nuclear Information System (INIS)

    O'Brien, R.S.

    1998-08-01

    This report describes a methodology for calculating the committed effective dose for mixtures of radionuclides, such as those which occur in natural radioactive ores and dusts. The formulae are derived from first principles, with the use of reasonable assumptions concerning the nature and behaviour of the radionuclide mixtures. The calculations are complicated because these 'ores' contain a range of particle sizes, have different degrees of solubility in blood and other body fluids, and also have different biokinetic clearance characteristics from the organs and tissues in the body. The naturally occurring radionuclides also tend to occur in series, i.e. one is produced by the radioactive decay of another 'parent' radionuclide. The formulae derived here can be used, in conjunction with a model such as LUDEP, for calculating total dose resulting from inhalation and/or ingestion of a mixture of radionuclides, and also for deriving annual limits on intake and derived air concentrations for these mixtures

  16. Uranium and thorium recovery in thorianite ore-preliminary results

    Energy Technology Data Exchange (ETDEWEB)

    Gaiotte, Joao V.M. [Universidade Federal de Alfenas, Pocos de Caldas, MG (Brazil); Villegas, Raul A.S.; Fukuma, Henrique T., E-mail: rvillegas@cnen.gov.br, E-mail: htfukuma@cnen.gov.br [Comissao Nacional de Energia Nuclear (CNEN), Pocos de Caldas, MG (Brazil). Lab. de Pocos de Caldas

    2011-07-01

    This work presents the preliminary results of the studies aiming to develop a hydrometallurgical process to produce uranium and thorium concentrates from thorianite ore from Amapa State, Brazil. This process comprises two major parts: acid leaching and Th/U recovery using solvent extraction strategies. Thorianite ore has a typical composition of 60 - 70% of thorium, 8 - 10% lead and 7 - 10% uranium. Sulfuric acid leaching operational conditions were defined as follows: acid/ore ratio 7.5 t/t, ore size below 65 mesh (Tyler), 2 hours leaching time and temperature of 100 deg C. Leaching tests results showed that uranium and thorium recovery exceeded 95%, whereas 97% of lead ore content remained in the solid form. Uranium and thorium simultaneous solvent extraction is necessary due to high sulfate concentration in the liquor obtained from leaching, so the Primene JM-T primary anime was used for this extraction step. Aqueous raffinate from extraction containing sulfuric acid was recycled to the leaching step, reducing acid uptake around 60%, to achieve a net sulfuric acid consumption of 3 t/t of ore. Uranium and thorium simultaneous stripping was performed using sodium carbonate solution. In the aqueous stripped it was added sulfuric acid at pH 1.5, followed by a second solvent extraction step using the tertiary amine Alamine 336. The following stripping step was done with a solution of sodium chloride, resulting in a final solution of 23 g L-1 uranium. (author)

  17. NRC's limit on intake of uranium-ore dust

    International Nuclear Information System (INIS)

    McGuire, S.A.

    1983-04-01

    In 1960 the Atomic Energy Commission adopted an interim limit on the intake by inhalation of airborne uranium-ore dust. This report culminates two decades of research aimed at establishing the adequacy of that limit. The report concludes that the AEC underestimated the time that thorium-230, a constituent of uranium-ore dust, would remain in the human lung. The AEC assumed that thorium-230 in ore dust would behave like uranium with a 120-day biological half-life in the lung. This report concludes that the biological half-life is actually on the order of 1 year. Correcting the AEC's underestimate would cause a reduction in the permitted airborne concentration of uranium-ore dust. However, another factor that cancels the need for that reduction was found. The uranium ore dust in uranium mills was found to occur with very large particle sizes (10-micron activity median aerodynamic diameter). The particles are so large that relatively few of them are deposited in the pulmonary region of the lung, where they would be subject to long-term retention. Instead they are trapped in the upper regions of the respiratory tract, subsequently swallowed, and then rapidly excreted from the body through the gastrointestinal tract. The two effects are of about the same magnitude but in opposing directions. Thus the present uranium-ore dust intake limit in NRC regulations should provide a level of protection consistent with that provided for other airborne radioactive materials. The report recalculates the limit on intake of uranium-ore dust using the derived air concentrations (DAC) from the International Commission on Radiological Protection's recent Publication 30. The report concludes that the silica contained in uranium-ore dust is a greater hazard to workers than the radiological hazard

  18. Studies on uranium ore processing

    International Nuclear Information System (INIS)

    Suh, I.S.; Chun, J.K.; Park, S.W.; Choi, S.J.; Lee, C.H.; Chung, M.K.; Lim, J.K.

    1983-01-01

    For the exploitation of domestic uranium ore deposit, comprehensive studies on uranium ore processing of the Geum-San pit ore are carried out. Physical and chemical characteristics of the Geum-San ore are similar to those of Goe-San ore and the physical beneficiation could not be applicable. Optimum operating conditions such as uranium leaching, solid-liquid separation, solvent extraction and precipitation of yellow cake are found out and the results are confirmed by the continous operation of the micro-plant with the capacity of 50Kg, ore/day. In order to improve the process of ore milling pilot plant installed recently, the feasibility of raffinate-recycle and the precipitation methods of yellow cake are intensively examined. It was suggested that the raffinate-recycle in the leaching of filtering stage could be reduced the environmental contamination and the peroxide precipitation technique was applicable to improve the purity of yellow cake. The mechanism and conditions the third phase formation are thoroughly studied and confirmed by chemical analysis of the third phase actually formed during the operation of pilot plant. The major constituents of the third phase are polyanions such as PMosub(12)Osub(40)sup(3-) or SiMosub(12)Osub(40)sup(4-). And the formation of these polyanions could be reduced by the control of redox potential and the addition of modifier. (Author)

  19. Chapter 1. General information about uranium. 1.3. Uranium ores

    International Nuclear Information System (INIS)

    Khakimov, N.; Nazarov, Kh.M.; Mirsaidov, I.U.

    2012-01-01

    The uranium ores were described. It was found that uranium ores and natural mineral formations containing uranium and its compounds, can be found in concentrations that are technically possible for industrial utilization and which are economically profitable. It was defined that oxidation levels of uranium minerals have an impact on their reprocessing technology and behavior in hydrometallurgical re partition. It was found that the chemical composition of ores has a decisive importance during selection of their reprocessing method.

  20. Decomposition of silica-alumina ores of Afghanistan by sulfuric acid

    International Nuclear Information System (INIS)

    Khomidi, A.K.; Mamatov, E.D.

    2016-01-01

    Present article is devoted to decomposition of silica-alumina ores of Afghanistan by sulfuric acid. Physicochemical properties of initial silica-alumina ores were studied by means of X-ray phase, differential thermal and silicate analysis. The influence of temperature, process duration and acid concentration on extraction rate of valuable components was considered. The optimal conditions of decomposition of silica-alumina ores of Afghanistan by sulfuric acid were proposed.

  1. Filtration aids in uranium ore processing

    International Nuclear Information System (INIS)

    Ford, H.L.; Levine, N.M.; Risdon, A.R.

    1975-01-01

    A process of improving the filtration efficiency and separation of uranium ore pulps obtained by carbonate leaching of uranium ore which comprises treating said ore pulps with an aqueous solution of hydroxyalkyl guar selected from the group consisting of hydroxyethyl and hydroxypropyl guar in the amount of 0.1 and 2.0 pounds of hydroxyalkyl guar per ton of uranium ore

  2. Rare earth elements materials production from apatite ores

    International Nuclear Information System (INIS)

    Anufrieva, A V; Buynovskiy, A S; Makaseev, Y N; Mazov, I N; Nefedov, R A; Sachkov, V I; Valkov, A V; Andrienko, O S; Stepanova, O B

    2016-01-01

    The paper deals with the study of processing apatite ores with nitric acid and extraction of the rare earth elements. The rare earth elements can be successfully separated and recovered by extraction from the nitrate- phosphate solution, being an tributyl phosphate as extraction agent. The developed scheme of the processing apatite concentrate provides obtaining rare earth concentrates with high qualitative characteristics. (paper)

  3. Ore sorting using natural gamma radiation

    International Nuclear Information System (INIS)

    Clark, G.J.; Dickson, B.L.; Gray, F.E.

    1980-01-01

    A method of sorting an ore which emits natural gamma radiation is described, comprising the steps of: (a) mining the ore, (b) placing, substantially at the mining location, the sampled or mined ore on to a moving conveyor belt, (c) measuring the natural gamma emission, water content and mass of the ore while the ore is on the conveyor belt, (d) using the gamma, water content and mass measurements to determine the ore grade, and (e) directing the ore to a location characteristic of its grade when it leaves the conveyor belt

  4. Study of the dry processing of uranium ores

    International Nuclear Information System (INIS)

    Guillet, H.

    1959-02-01

    A description is given of direct fluorination of pre-concentrated uranium ores in order to obtain the hexafluoride. After normal sulfuric acid treatment of the ore to eliminate silica, the uranium is precipitated by a load of lime to obtain: either impure calcium uranate of medium grade, or containing around 10% of uranium. This concentrate is dried in an inert atmosphere and then treated with a current of elementary fluorine. The uranium hexafluoride formed is condensed at the outlet of the reaction vessel and may be used either for reduction to tetrafluoride and the subsequent manufacture of uranium metal or as the initial product in a diffusion plant. (author) [fr

  5. A Review on New Technological Progress for Beneficiation of Refractory Phosphate Ore in China

    Science.gov (United States)

    Dong, Xu; Siqing, Liu; Yanqing, Yao; Hailin, Liu; Yi, Pei

    2017-05-01

    The world is rich in phosphate resources, but the vast majority of the resources are of middle and low grade ores, and it is difficult to obtain high grade concentrate at a high recovery by using traditional separation methods. In this paper, the distribution and flotation processes of typical phosphate ores in China are introduced. Considering the current situation in phosphate ore beneficiation both home and abroad, the new trend of processing technology and reagents in China are summarized. Flotation is still regarded as the main processing method in phosphate ore beneficiation for a certain time in near future.

  6. X-ray fluorescence separation of pure lead-zinc ores

    International Nuclear Information System (INIS)

    Lapshin, S.A.; Filippov, O.K.; Khachatryan, L.S.; Rudnev, B.P.

    1987-01-01

    To evaluate the influence of the previous concentration of polymetallic ores by the radiometric separation method on indices of flotation and gravitation enrichments, investigations were carried out using ore sample (1.94%Pb, 1.13% Zn) from a lead-zink ore deposit. It is shown that the results obtained on the enrichment of the ore and products of X-ray radiometric separation are similar. However previous removal (up to 40%) of dead rock permits to reduce sharply grinding and transpot costs

  7. Direct Biohydrometallurgical Extraction of Iron from Ore

    Energy Technology Data Exchange (ETDEWEB)

    T.C. Eisele

    2005-10-01

    A completely novel approach to iron extraction was investigated, based on reductive leaching of iron by anaerobic bacteria. Microorganisms were collected from an anaerobic bog where natural seepage of dissolved iron was observed. This mixed culture was used to reduce insoluble iron in a magnetite ore to the soluble ferrous (Fe{sup +2}) state. While dissolution rates were slow, concentrations of dissolved iron as high as 3487 mg/l could be reached if sufficient time was allowed. A factorial study of the effects of trace nutrients and different forms of organic matter indicated that the best dissolution rates and highest dissolved iron concentrations were achieved using soluble carbohydrate (sucrose) as the bacterial food source, and that nutrients other than nitrogen, phosphorus, potassium, sodium, and acetate were not necessary. A key factor in reaching high levels of dissolved iron was maintaining a high level of carbon dioxide in solution, since the solubility of iron carbonates increases markedly as the quantity of dissolved carbon dioxide increases. Once the iron is dissolved, it has been demonstrated that the ferrous iron can then be electroplated from solution, provided that the concentration of iron is sufficiently high and the hydrogen ion concentration is sufficiently low. However, if the leaching solution is electrolyzed directly, organic matter precipitates at the cathode along with the metallic iron. To prevent this problem, the ferrous iron should be separated from the bulk solution in a more concentrated, purified form. One route to accomplishing this is to take advantage of the change in solubility of ferrous iron as a function of carbon dioxide concentration. By cycling the concentration of carbon dioxide in solution, it is possible to produce an iron-rich concentrate that should be suitable for electrolysis. This represents the first viable hydrometallurgical method for leaching iron directly from ore and producing metallic iron.

  8. Radiometric enrichment of nonradioactive ores

    International Nuclear Information System (INIS)

    Mokrousov, V.A.; Lileev, V.A.

    1979-01-01

    Considered are the methods of mineral enrichment based on the use of the radioation of various types. The physical essence of enrichment processes is presented, their classification is given. Described are the ore properties influencing the efficiency of radiometric enrichment, methods of the properties study and estimation of ore enrichment. New possibilities opened by radiometric enrichment in the technology of primary processing of mineral raw materials are elucidated. A considerable attention is paid to the main and auxiliary equipment for radiometric enrichment. The foundations of the safety engineering are presented in a brief form. Presented are also results of investigations and practical works in the field of enrichment of ores of non-ferrous, ferrous and non-metallic minerals with the help of radiometric methods

  9. Thermodynamic Analysis of the Selective Reduction of a Nickeliferous Limonitic Laterite Ore by Hydrogen

    Science.gov (United States)

    Elliott, R.; Pickles, C. A.

    2017-09-01

    Nickeliferous limonitic laterite ores are becoming increasingly attractive as a source of metallic nickel as the costs associated with recovering nickel from the sulphide ores increase. Unlike the sulphide ores, however, the laterite ores are not amenable to concentration by conventional mineral processing techniques such as froth flotation. One potential concentrating method would be the pyrometallurgical solid state reduction of the nickeliferous limonitic ores at relatively low temperatures, followed by beneficiation via magnetic separation. A number of reductants can be utilized in the reduction step, and in this research, a thermodynamic model has been developed to investigate the reduction of a nickeliferous limonitic laterite by hydrogen. The nickel recovery to the ferronickel phase was predicted to be greater than 95 % at temperatures of 673-873 K. Reductant additions above the stoichiometric requirement resulted in high recoveries over a wider temperature range, but the nickel grade of the ferronickel decreased.

  10. Mining, ore preparation and niobium alloys production at Araxa, Brazil

    International Nuclear Information System (INIS)

    Paraiso, O.S.; Fuccio Junior, R. de; Betz, E.W.

    1984-01-01

    A detailed description of the worlds major niobium producer is presented covering mining, concentration by froth flotation, leaching, and production of ferro-alloys. The present exploration of the Araxa deposit, its ore preparation and production of ferro-niobium is described. (E.G.) [pt

  11. Composition and method for solution mining of uranium ores

    International Nuclear Information System (INIS)

    Lawes, B.C.; Watts, J.C.

    1981-01-01

    It has been found that, in the solution mining of uranium ores using ammonium carbonate solutions containing hydrogen peroxide or ozone as an oxidant, the tendency of the formation being treated to become less permeable during the leaching process can be overcome by including in the leaching solution a very small concentration of sodium silicate

  12. Origin of ores of endogeneous uranium ore deposits

    International Nuclear Information System (INIS)

    Kasanskij, V.I.; Laverov, N.P.; Tugarinov, A.I.

    1976-01-01

    The consideration mainly includes those endogenous uranium ore deposits of which more exact data are available, such as precambrian ones in areas of proto-activated old platforms, deposits of palaeozoic fold areas, and mesozoic deposits in areas of tectonic-magnetic activation. Their genesis and typical characters are mentioned and conclusions on the general distribution of the deposits are drawn. (author)

  13. Can micro-PIXE measurements help to determine ore genesis ?

    International Nuclear Information System (INIS)

    Ahmed, M.; Al-Ohali, M.A.

    2002-01-01

    This study is an attempt to demonstrate how the nuclear micro-PIXE technique can be utilized to investigate ore genesis of geological deposits. Elemental concentrations and distribution profiles in single mineral grains and matrices in a present-day ore deposit on land were measured using the scanning proton microprobe on the 3 MV Tandetron accelerator at King Fahd University of Petroleum and Minerals. Comparing the distribution profiles of some of the trace elements detected it was possible to suggest an organic, sea origin of these deposits. (Author)

  14. Oxidizing attack process of uranium ore by a carbonated liquor

    International Nuclear Information System (INIS)

    Maurel, Pierre; Nicolas, Francois.

    1981-01-01

    A continuous process for digesting a uraniferous ore by oxidation with a recycling aqueous liquor containing alkaline carbonates and bicarbonates in solution as well as uranium in a concentration close to its solubility limit at digestion temperature, and of recuperation of the precipitated uranium within the solid phase remaining after digestion. The digestion is carried out by spraying oxygen into the hot reactional medium in order not only to permit oxidation of the uranium and its solubilization but also to ensure that the sulphides of impurities and organic substances present in the ore are oxidized [fr

  15. Manual on laboratory testing for uranium ore processing

    International Nuclear Information System (INIS)

    1990-01-01

    Laboratory testing of uranium ores is an essential step in the economic evaluation of uranium occurrences and in the development of a project for the production of uranium concentrates. Although these tests represent only a small proportion of the total cost of a project, their proper planning, execution and interpretation are of crucial importance. The main purposes of this manual are to discuss the objectives of metallurgical laboratory ore testing, to show the specific role of these tests in the development of a project, and to provide practical instructions for performing the tests and for interpreting their results. Guidelines on the design of a metallurgical laboratory, on the equipment required to perform the tests and on laboratory safety are also given. This manual is part of a series of Technical Reports on uranium ore processing being prepared by the IAEA's Division of Nuclear Fuel Cycle and Waste Management. A report on the Significance of Mineralogy in the Development of Flowsheets for Processing Uranium Ores (Technical Reports Series No. 196, 1980) and an instruction manual on Methods for the Estimation of Uranium Ore Reserves (No. 255, 1985) have already been published. 17 refs, 40 figs, 17 tabs

  16. Radon and Thoron emanation testwork on Nolans Rare Earths ores

    International Nuclear Information System (INIS)

    Sonter, Mark; Grose, Jeremy

    2016-01-01

    This paper reports on a series of experiments performed on two bulk ore samples for Arafura Resources' Nolans Rare Earths project, intended to derive information on radon (Rn222) and thoron (Rn220) emanation rates (fluxes) under various circumstances. This data is needed to enable development of predictions of Rn and Tn releases from exposed mine bench ore, ore stockpiles, and tailings, and thus assist in estimation of airborne concentrations within the areas of the future Mine and Processing plant. In turn these estimates will provide guidance on the quantitative risk and the necessity or otherwise of invoking specific control measures, either in design or in operating procedures. This testwork was carried out during the period 2nd to 15th July, at Arafura's Winnellie facility in Darwin. Conclusions are that for uncrushed ore, Rn flux numbers are around 1.0Bq/m"2/s, Tn numbers appear to cluster around 200-300 Bq/m"2/s. Crushing gave no change in Rn flux, Tn flux was doubled for calc-silicate material. Wetting gave significant reductions for both Rn and Tn for ores sampled, and clay capping reduced Rn flux marginally but Tn was reduced by a factor of 100.

  17. Sintering-alkaline processing of borosilicate ores of Tajikistan

    International Nuclear Information System (INIS)

    Nazarov, F.A.

    2018-01-01

    The aim of the work is to study the processes of decomposition of boron-containing ore by sintering with NaOH, finding the optimal parameters of the decomposition process, studying the kinetics of processes and developing the technological foundations for ore processing. The processes of borosilicate ore processing were studied by sintering with NaOH. Possible mechanisms of chemical reactions of the process of sintering-alkaline decomposition of boron-containing ore are established, the results of which are substantiated by physicochemical methods of analysis. A principal technological scheme for processing of borosilicate ores by a sintering-alkaline method has been developed. In the first chapter, data on alkaline and caking processes for processing boron-containing and aluminium comprising raw materials are available in the literature. Based on this, the directions of our own research are outlined. The second chapter is devoted to the study of the chemical and mineralogical compositions of borosilicate ores and their concentrates with the help of X-ray phase and chemical analysis methods, the stoichiometric calculation of the formation of aluminum, iron, and boron salts has been carried out, and a thermodynamic analysis of the processes of sintering borosilicate ores with alkali has been considered. The third chapter presents the results of a study of sintering-alkaline method of processing of initial borosilicate ore of the Ak-Arkhar Deposit and its concentrate without calcination and after calcination. The kinetics of sintering of borosilicate ores with sodium hydroxide was studied. The optimal conditions of borosilicate ore sintering before and after the preliminary calcination with alkali were determined. Optimal parameters of the sintering process have been found: sintering temperature 800-8500 deg C, duration of the process - 60 minutes, mass ratio of NaOH to raw materials 2: 1. The conditions for sintering of borosilicate concentrate with alkali have been

  18. Flotation study on scheelite ore of chitral khyber pakhtoonkhwa, pakistan

    International Nuclear Information System (INIS)

    Bhatti, M.A.; Kazmi, K.R.; Mehmood, R.; Akram, A.

    2014-01-01

    The beneficiation of a siliceous scheelite ore of Chitral, Khyber Pakhtoonkhwa, Pakistan, was investigated by flotation process to determine the optimum conditions for obtaining maximum grade and recovery of the scheelite concentrate. The variables studied were including pH and pulp density maintained during conditioning, type and quantity of reagents added, conditioning time and froth collecting time. The results achieved were plotted against the grade and recovery of the rougher concentrate. Several methods of cleaning rougher concentrate were attempted. An ore initially containing 0.34% WO/sub 3/ was upgraded into a final concentrate assaying 64.66% WO/sub 3/ with 70.36% recovery. The tungsten concentrate obtained meets the specifications required to produce ferrotungsten and tungsten chemicals. (author)

  19. Application of X-ray luminescence separation to preliminary enrichment of lean scheelite-containing ores

    International Nuclear Information System (INIS)

    Zhaboev, M.N.; Semochkin, G.A.; Blinov, Yu.I.; Dzhambaev, F.M.; Novikov, V.V.; Tereshchenko, S.V.

    1987-01-01

    Investigations of preliminary enrichment of lean ores of amphibole hornfels by the method of X-ray luminescence separation was conducted. Pile and enriched products with different WO 3 content were obtained from these ores; WO 3 content in pile products was 2-2.5 times lower as compared to factory tailing products. WO 3 content in separator concentrate corresponds in all cases to the requirements for the ore designated for flotation enrichment. Carbonate modulus decreases 2.5-4 times in separation concentrate, simplifying the conditions of flotation

  20. Thorium content of a mineral ore from Morro do Ferro by fission track technique

    International Nuclear Information System (INIS)

    Oliveira, C.A.N. de.

    1980-10-01

    The feasibility to determine thorium concentrations by fission track technique in samples of mineral ore has been demonstrated. The literature registers only the application of the fission track technique to mineral ore in the case where the fissionable element is uranium. The technique was applied to determine the thorium concentration of an ore sample from Morro do Ferro, taking advantage of the high thorium to uranium ratio in that mineral. The sample analysed presented a thorium concentration of 2467 +- 400 mg Th/Kg ore. The so called wet method was adopted by using the Bayer made Makrofol KG 10μm thick, as the detector foil, immersed in the thorium solution. The technique is also useful to determine thorium concentrations in environmental samples because of the following aspects: high sensitivity; fast chemical separation of interfering elements; low cost; and operational simplicity. (Author) [pt

  1. Moessbauer study of the chemical state of gold in gold ores

    International Nuclear Information System (INIS)

    Wagner, F.E.; Marion, P.H.; Regnard, J.-R.

    1986-01-01

    Information on the chemical state of gold in gold ores has been obtained by 197 Au Moessbauer spectroscopy in cases where the state of this element cannot be determined by such standard methods as optical or electron microscopy. Ore concentrates consisting mainly of pyrite or arsenopyrite and roasted ore and matte samples were studied. The results yielded directly the respective amounts of metallic and chemically bound gold. Unless the gold is metallic, its chemical state in the ores turns out to be different from that in the minerals studied so far as reference materials. The chemical processes taking place during various treatments of the ores, such as roasting or leaching, can also be followed by Moessbauer spectroscopy. It is hoped that Moessbauer spectroscopy will eventually facilitate the development of more efficient methods of gold extraction

  2. Leaching of U, 230Th and 226Ra from Saskatchewan uranium ore after removing clay

    International Nuclear Information System (INIS)

    Muthuswami, S.V.; Mohd Yunus, M.Z.; Mohamad Nor, M.I.; Kassim, Z.A.; Nirdosh, I.

    1993-01-01

    Distribution of U, 230 Th and 226 Ra in various size fractions in a typical Saskatchewan uranium ore and its resultant mill tailings indicated that less than 4% of these radionuclides were present in the fine ≤ 45 μm) size fraction in the ore whereas their concentration in the similar size fraction in the tailings was > 80%. Removal of clay minerals from the ore by flotation was unsuccessful whereas sedimentation gave nearly complete removal. Leaching of 230 Th from the ore before and after removing clay minerals indicated that dissolution of 230 Th was mproved at higher E h and acidity of the leaching medium and that it was independent of the presence of clay minerals in the ore. (orig.) [de

  3. Processing of low-grade uranium ores

    International Nuclear Information System (INIS)

    Michel, P.

    1975-01-01

    Four types of low grade ores are studied. Low grade ores which must be extracted because they are enclosed in a normal grade deposit. Heap leaching is the processing method which is largely used. It allows to obtain solutions or preconcentrates which may be delivered at the nearest plant. Normal grade ores contained in a low amplitude deposit which can be processed using leaching as far as the operation does not need any large expensive equipment. Medium grade ores in medium amplitude deposits to which a simplified conventional process can be applied using fast heap leaching. Low grade ores in large deposits. The processing possibilities leading to use in place leaching are explained. The operating conditions of the method are studied (leaching agent, preparation of the ore deposit to obtain a good tightness with regard to the hydrological system and to have a good contact between ore and reagent) [fr

  4. Flotation of uranium from uranium ores in Canada. Part 2

    International Nuclear Information System (INIS)

    Muthuswami, S.V.; Vijayan, S.; Woods, D.R.

    1985-01-01

    Measurements are reported for the equilibrium of cupferron from solutions by uranium oxide, quartz, illite, a mixture of these three, pitchblende, pyrite and brannerite ore. The cupferron concentration ranged from 1 to 6 g/L, and the pH was 7 and 8. Most isotherms followed the Langmuir model, although Freundlich behaviour was observed for illite and pitchblende. Most adsorption was pH independent except for illite and pitchblende. The adsorption isotherms for a mixture of uranium oxide, quartz and illite in the same proportions as in the naturally occurring ore agreed with the adsorption of the pyrite-free ore at pH 8 but not pH 7. We attribute the discrepancy to the use of illite as the model clay. The specific adsorption of cupferron on quartz and illite is lower by a factor of about 50 and 5, respectively, than the adsorption on uranium oxide. Specific adsorption less than 1 mg cupferron per gm of pyrite free ore does not float the mineral. The corresponding equilibrium concentration of cupferron is 0.5 g/L. A qualitative model is given, and the implications of this work for practical operations are presented

  5. Influence of attrition variables on iron ore flotation

    Directory of Open Access Journals (Sweden)

    Fabiana Fonseca Fortes

    Full Text Available Abstract The presence of slimes is harmful to the flotation process: the performance and consumption of reagents are negatively affected. Traditionally, the desliming stage has been responsible for removing slimes. However, depending on the porosity of the mineral particles, desliming may not be sufficient to maximize the concentration results. An attrition process before the desliming operation can improve the removal of slime, especially when slimes cover the surface and/or are confined to the cavities/pores of the mineral particles. Attrition is present in the flowcharts of the beneficiation process of phosphate and industrial sand (silica sand. Research has been undertaken for its application to produce pre-concentrates of zircon and iron ore. However, there is still little knowledge of the influence of the attrition variables on the beneficiation process of iron ore. This study presents a factorial design and analysis of the effects of these variables on the reverse flotation of iron ore. The standard of the experimental procedures for all tests included the attrition of pulp, under the conditions of dispersion, desliming and flotation. The parameter analysed (variable response was the metallurgical recovery in reverse flotation tests. The planning and analysis of the full factorial experiment indicated that with 95% reliability, the rotation speed of the attrition cell impeller was the main variable in the attrition process of the iron ore. The percentage of solid variables in the pulp and the time of the attrition, as well as their interactions, were not indicated to be significant.

  6. Studies of leaching of copper ores and flotation wastes

    International Nuclear Information System (INIS)

    Wawszczak, D.; Deptula, A.; Lada, W.; Smolinski, T.; Olczak, T.; Brykala, M.; Wojtowicz, P.; Rogowski, M.; Milkowska, M.; Chmielewski, A.G.

    2014-01-01

    In Poland, there are significant deposits of copper ores. During the copper extraction, large amounts of flotation wastes are produced. In the ores and flotation wastes many other important elements are present. The main goal of this work was analysis of uranium content and to elaborate procedures for recovery of U from these materials. Two types of ores and four types of waste were examined. It has been found that uranium content varies from 4.5 to 25 ppm. The other elements have also been determined in these materials: Cu (4-5 % in ores and 0.3-1.7 % in waste), Ag, Re, Mo, La, Ni, V, etc. For leaching, sulfuric acid and sodium carbonates of various concentrations (temperature, time) were used. The optimum conditions for leaching have been found. The concentration of uranium in the final solution was generally less than 25 μg/mL. The other elements are also present in the leaching solutions. Simultaneous liquid-liquid extraction of uranium with these elements from leaching solution is under study. In our opinion, only such combined procedure for the recovery of uranium together with the accompanying elements could be cost-effective. (author)

  7. Ore microscopy applied to beneficiation

    International Nuclear Information System (INIS)

    Hagni, R.D.

    1978-01-01

    Ore microscopy can be an important adjunct to beneficiation, because it can be used not only to predict mill problems of undeveloped ore deposits but to identify the causes for the loss of minerals in the products of operating mines and mills. Mineral distribution among various mill products can be determined by examining polished sections prepared from samples obtained from each step of the beneficiation process. The degree of liberation of each mineral can be quantitatively determined for each mill product by counting locked vs. free particles. For many beneficiation problems, the preparation of a few polished sections of carefully selected mill products can yield useful information, which the mill dressing engineer can effectively use to alleviate those problems

  8. Uranium extraction from ores with salicylic acid; I - uranium extraction from input phosphate ore of Abu Zaabal phosphate plant, Egypt

    International Nuclear Information System (INIS)

    Hussein, E.M.

    1997-01-01

    Salicylic acid has been tested (for environmental importance) to extract U from input phosphate ore of Abu-Zaabal phosphate plant, Egypt prior to its processing for production of phosphatic fertilizers. Uranyl ion forms with this acid three stable complexes; namely [UO 2 Sal] degree, [U O 2 SaL 2 ] 2- and UO 2 SaL-3] 4- depending on the total uranyl and salicylic acid concentrations and their ratios. Study of relevant extraction factors revealed however that, the extraction process is controlled by the amount of salicylic acid used, alcohol/aqueous ratio, solid/liquid ratio and time of agitation. The obtained results showed that uranium is selectively leached by the application of such a leaching reagent. In order to recover U from the obtained pregnant leach liquor, the latter is adjusted by ammonia to PH 5-6.5, where the crystalline pp t of N H 4 [UO 2 SaL 3 ] 4 H 2 O has formed. This precipitation has been carried out after concentrating the obtained pregnant leach liquor by its recycle for U extraction from new ore batches. The precipitated ammonium uranyl tri salicylate is calcined at 500 degree C for obtaining pure orange yellow trioxide (UO 3 ) powder. On the basis of one ton ore treatment, an economic flowsheet for U recover y from the study ore material has been suggested

  9. Radioactivity of phosphate ores from Karatas-Mazidag phosphate deposit of Turkey

    International Nuclear Information System (INIS)

    Akyuez, T.; Varinlioglu, A.; Kose, A.; Akyuez, S.

    2000-01-01

    The specific activities of 238 U, 226 Ra, 232 Th and 40 K in the composite samples of phosphate ores of type I (grey-coloured ore, with high P 2 O 5 (21-35%) and low calcite content) and of type II (grey coloured calcite ore, with low P 2 O 5 content (5-17%)) of Karatas-Mazidag phosphate deposit, Turkey, have been determined by gamma spectrometry together with phosphatic animal feed ingredients. The concentrations of 238 U, 226 Ra, 232 Th and 40 K were found to be up to 557, 625, 26 and 297 Bq x kg -1 , respectively. Radium equivalent activities of samples were calculated and compared with those given in the literature. Uranium concentration of the individual phosphate samples, from which composite samples of ores of type I and II have been prepared, were found to show and increasing trend with increasing P 2 O 5 and F concentrations. (author)

  10. Vat leaching of gold ores and utilization of the tailings; Kinkoseki no vat leaching to koshi no yuko riyo

    Energy Technology Data Exchange (ETDEWEB)

    Hosooka, T. [Nippon Clay Mining Co. Ltd., Tokyo (Japan); Miyagawa, H. [Mitsui Mining and Smelting Co. Ltd., Tokyo (Japan)

    1996-01-25

    Mitsui Kushikino Mine previously processed two gold ores from Kushikino and Iwato ore deposits by the all slime cyanidation method, where the ores were ground to fine size smaller than 75 {mu}m and leached with sodium, cyanide. A large amount of slimes were produced as waste and discarded in tailings ponds. To save the costs of grinding and waste treatment it is desirable to process coarse sized ores. The Iwato ore is gold and silver bearing silicified porous rock. As most gold and silver in the Iwato ore are concentrated in the pores, leaching of coarse sized ore is expected to be possible. Laboratory tests and pilot plant tests of vat leaching for the Iwato ore were carried out using 0.15-8.0 mm feed. These results showed that the gold dissolution rate was similar to that by the all slime cyanidation and the decrease in gold recovery was a few %. The properties of these tailings can be used in fine aggregate of concrete. Based on the results vat leaching of the Iwato ore was adopted in the plant. The tailings are sold and used as fine aggregate. Utilization of slime tailings from the other ores was also developed and they are used as flux in copper smelters. Now, there is no tailings pond at Mitsui Kushikino Mine. 9 refs., 10 figs., 5 tabs.

  11. The flotation of Roşia Poieni copper ore in column machine, with non-polar oils addition

    Directory of Open Access Journals (Sweden)

    Ciocani V.

    2005-11-01

    Full Text Available The most important natural resource of copper in Romania is the ore deposit of Roşia Poieni. At present, the utilization of Roşia Poieni poorphyry copper ore is possible by extraction in quarry of the mass ore and mineral processing into a technological flux with modest results for the value of metal recovery in concentrate 70-72 % and an average contents of 16,5 % Cu. Our researches were directed to studies regarding test and utilisation of special procedure of flotation – addition of the non-polar oil – applied to advanced grinding ore with column type machines.

  12. Microwave enhanced recovery of nickel-copper ore: communition and floatability aspects.

    Science.gov (United States)

    Henda, R; Hermas, A; Gedye, R; Islam, M R

    2005-01-01

    A study describing the effect of microwave radiation, at a frequency of 2450 MHz, on the processes of communication and flotation of a complex sulphide nickel-copper ore is presented. Ore communication has been investigated under standard radiation-free conditions and after ore treatment in a radiated environment as a function of ore size, exposure time to radiation, and microwave power. The findings show that communication is tremendously improved by microwave radiation with values of the relative work index as low as 23% at a microwave power of 1.406 kW and after 10 s of exposure time. Communication is affected by exposure time and microwave power in a nontrivial manner. In terms of ore floatability, the experimental tests have been carried out on a sample of 75 microm in size under different exposure times. The results show that both ore concentrate recoveries and grades of nickel and copper are significantly enhanced after microwave treatment of the ore with relative increases in recovered concentrate, grade of nickel, and grade of copper of 26 wt%, 15 wt%, and 27%, respectively, at a microwave power of 1330 kW and after 30 s of exposure time.

  13. Application of Concentration-Number and Concentration-Volume Fractal Models to Recognize Mineralized Zones in North Anomaly Iron Ore Deposit, Central Iran / Zastosowanie Modeli Fraktalnych Typu K-L (Koncentracja-Liczba), Oraz K-O (Koncentracja Objętość) Do Rozpoznawania Stref Występowania Surowców Mineralnych W Regionie Złóż Rud Żelaza North Anomaly, W Środkowym Iranie

    Science.gov (United States)

    Afzal, Peyman; Ghasempour, Reza; Mokhtari, Ahmad Reza; Haroni, Hooshang Asadi

    2015-09-01

    Identification of various mineralized zones in an ore deposit is essential for mine planning and design. This study aims to distinguish the different mineralized zones and the wall rock in the Central block of North Anomaly iron ore deposit situated in Bafq (Central Iran) utilizing the concentration-number (C-N) and concentration-volume (C-V) fractal models. The C-N model indicates four mineralized zones described by Fe thresholds of 8%, 21%, and 50%, with zones 50% Fe representing wall rocks and highly mineralized zone, respectively. The C-V model reveals geochemical zones defined by Fe thresholds of 12%, 21%, 43% and 57%, with zones 50% zawartości żelaza, co odpowiada pasmu skalnemu oraz strefie o wysokim stopniu zawartości rudy. Model koncentracja-objętość wskazuje na istnienie stref geochemicznych określonych poprzez progowe wartości zawartości żelaza: 12%, 21%, 43% i 57 % oraz strefy <12%, co odpowiada ścianie skalnej. Obydwa modele stwierdzają obecność stref o wysokim stopniu zawartości surowca w środkowej i zachodniej części złoża. Wyniki walidacji modeli fraktalnych przy użyciu modeli geologicznych wskazują, ze model fraktalny koncentracja-liczba lepiej odwzorowuje obecność stref o wysokiej zawartości rud niż model fraktalny typu koncentracja-objętość.

  14. Microbial leaching of low grade copper ores

    International Nuclear Information System (INIS)

    Rauf, A.; Ashfaq, M.

    1991-01-01

    Biotechnology is regarded as one of the most promising and revolutionary solution to various problems which are generally faced in the extraction of metals from their ores such as high energy, capital costs and environmental pollution. The paper deals with the study of low grade copper ores for their beneficiation and extraction of copper. The ores used were chalcopyrite and oxidized copper ores. Microorganisms play a vital role in the solubilization of valuable contents from ores such as copper and other metals. Studies have been conducted on the indigenous copper ores by using thiobacillus ferro oxidans and thiobacillus thio oxidans. For comparison purpose some experiments have also been conducted by chemical leaching. The results of bacterial leaching are encouraging. (author)

  15. Processing of low grade uranium ores

    International Nuclear Information System (INIS)

    Michel, P.

    1978-10-01

    Four types of low-grade ores are studied: (1) Low-grade ores that must be extracted because they are enclosed in a normal-grade deposit. Heap leaching is the processing method which is largely used. (2) Normal-grade ores contained in low-amplitude deposits. They can be processed using in-place leaching as far as the operation does not need any large and expensive equipment. (3) Medium-grade ores in medium-amplitude deposits. A simplified conventional process can be applied using fast heap leaching. (4) Low-grade ores in large deposits. The report explains processing possibilities leading in most cases to the use of in-place leaching. The operating conditions of this method are laid out, especially the selection of the leaching agents and the preparation of the ore deposit

  16. Technological pretreatment of the synchysite non-oxidized ore

    Science.gov (United States)

    Munkhtsetseg, B.; Burmaa, G.

    2013-06-01

    Mongolia has rich deposits of rare, precious, and poly-metallic ores. Nowadays, it is important to research separation of rare earth elements oxides concentrates from the ores, analyze their unique physical chemical characteristics, and purified it. Our investigation on raw materials focuses on rare earth non-oxidized ores. Main mineral in this rock sample is Synchysite (LnCa(CO3)2F. We did technological and thermal pretreatment: direct sulphurization (H2SO4), sulphurization with subsequent roasting (800°C+H2SO4), sulphurization prior to roasting (H2SO4+650°C). Sulphurization method based on dissolution of rare earth mineral into sulfuric acid (93%) according to the reaction. The amount of rare earth element oxides is almost 10 times greater (29.16%) after direct sulphurization process, almost 8 times greater (21.14%) after sulphurization with subsequent roasting, and almost 20 times greater (44.62%) after sulphurization prior to roasting process. After those technological pretreatment raw material's micro elements Thorium and Uranium contents are reduced as follows: H2SO4>800°C+H2SO4>H2SO4+650°C. These results show that cerium group rare earth elements have very good solubility in water at +2°C temperature and decreasing micro elements content uranium and thorium good pretreatment condition is prior to roasting (H2SO4+650°C) of synchysite non-oxidized ore.

  17. Hemimorphite Ores: A Review of Processing Technologies for Zinc Extraction

    Science.gov (United States)

    Chen, Ailiang; Li, Mengchun; Qian, Zhen; Ma, Yutian; Che, Jianyong; Ma, Yalin

    2016-10-01

    With the gradual depletion of zinc sulfide ores, exploration of zinc oxide ores is becoming more and more important. Hemimorphite is a major zinc oxide ore, attracting much attention in the field of zinc metallurgy although it is not the major zinc mineral. This paper presents a critical review of the treatment for extraction of zinc with emphasis on flotation, pyrometallurgical and hydrometallurgical methods based on the properties of hemimorphite. The three-dimensional framework structure of hemimorphite with complex linkage of its structural units lead to difficult desilicification before extracting zinc in the many metallurgical technologies. It is found that the flotation method is generally effective in enriching zinc minerals from hemimorphite ores into a high-grade concentrate for recovery of zinc. Pure zinc can be produced from hemimorphite or/and willemite with a reducing reagent, like methane or carbon. Leaching reagents, such as acid and alkali, can break the complex structure of hemimorphite to release zinc in the leached solution without generation of silica gel in the hydrometallurgical process. For optimal zinc extraction, combing flotation with pyrometallurgical or hydrometallurgical methods may be required.

  18. Applicability of attrition of iron ore in floating

    International Nuclear Information System (INIS)

    Fortes, Fabiana Fonseca

    2010-01-01

    The aim of this study is to investigate the possibility to increase metal recovery in the flotation of iron ore with the implementation of a stage of scrubbing followed by dispersion. The minerals in question stems from two mines located in the western portion of the Iron Quadrangle and differ mainly with respect to the percentage of hematite and porous and the presence of aggregated masses. These characteristics were compared to those of other minerals that have succeeded with the adoption of this technique. Tests were conducted at bench scale scrubbing, desliming and concentration by flotation with the blend of ore from both mines. Were varied stirring time and pH. The chemical results of desliming and flotation products in the different conditions were compared. The presence of porous hematite is relevant in a mine, mainly due to the occurrence of earthy goethite, alumina carrier of the contaminant. The step desliming is insufficient for the removal of harmful sludge flotation. Laboratory experiments showed that the scrubbing of the pulp of iron ore of Minas de Capitao do Mato and Tamandua, agitated for 10 minutes followed by desliming amid scattered, promotes increased metal recovery by about 17% and increases the selectivity of 40 % compared to the results of the scrubbing and without dispersion. The scrubbing of hematite ore followed by desliming amid scattered can bring gains in improving the quality of pellet feed fine if deployed industrially. (author)

  19. Natural Ores as Oxygen Carriers in Chemical Looping Combustion

    Energy Technology Data Exchange (ETDEWEB)

    Tian, Hanjing; Siriwardane, Ranjani; Simonyi, Thomas; Poston, James

    2013-08-01

    Chemical looping combustion (CLC) is a combustion technology that utilizes oxygen from oxygen carriers (OC), such as metal oxides, instead of air to combust fuels. The use of natural minerals as oxygen carriers has advantages, such as lower cost and availability. Eight materials, based on copper or iron oxides, were selected for screening tests of CLC processes using coal and methane as fuels. Thermogravimetric experiments and bench-scale fixed-bed reactor tests were conducted to investigate the oxygen transfer capacity, reaction kinetics, and stability during cyclic reduction/oxidation reaction. Most natural minerals showed lower combustion capacity than pure CuO/Fe{sub 2}O{sub 3} due to low-concentrations of active oxide species in minerals. In coal CLC, chryscolla (Cu-based), magnetite, and limonite (Fe-based) demonstrated better reaction performances than other materials. The addition of steam improved the coal CLC performance when using natural ores because of the steam gasification of coal and the subsequent reaction of gaseous fuels with active oxide species in the natural ores. In methane CLC, chryscolla, hematite, and limonite demonstrated excellent reactivity and stability in 50-cycle thermogravimetric analysis tests. Fe{sub 2}O{sub 3}-based ores possess greater oxygen utilization but require an activation period before achieving full performance in methane CLC. Particle agglomeration issues associated with the application of natural ores in CLC processes were also studied by scanning electron microscopy (SEM).

  20. Discussion on prospecting potential for rich uranium deposits in Xiazhuang uranium ore-field, northern Guangdong

    International Nuclear Information System (INIS)

    Wu Lieqin; Tan Zhengzhong

    2004-01-01

    Based on analyzing the prospecting potential for uranium deposits in Xiazhuang uranium ore field this paper discusses the prospecting for rich uranium deposits and prospecting potential in the region. Research achievements indicate: that the Xiazhuang ore-field is an ore-concentrated area where uranium has been highly enriched, and possesses good prospecting potential and perspective, becoming one of the most important prospecting areas for locating rich uranium deposits in northern Guangdong; that the 'intersection type', the alkaline metasomatic fractured rock type and the vein-group type uranium deposits are main targets and the prospecting direction for future uranium prospecting in this region

  1. X-ray radiometric separation of low-grade tin ores

    Energy Technology Data Exchange (ETDEWEB)

    Kotler, N.I.; Neverov, A.D.; Konovalov, V.M.; Mironov, I.I.; Zakharov, S.N.

    1984-10-01

    The investigations on evaluation of X-ray radiometric separation of off-grade tin ores of one of the deposits are carried out. The experiments have been performed at loboratory and pilot-commerical plants. /sup 241/Am has been used as a radiation source. In the course of facility commercial the ore has been separated by means of a device comprising a separator and gate separatin device. The results of X-ray radiometric separation have shown its high productive efficiency. Concentrates with higher tin content at high extraction from ores are obtained.

  2. X-ray radiometric separation of low-grade tin ores

    International Nuclear Information System (INIS)

    Kotler, N.I.; Neverov, A.D.; Konovalov, V.M.; Mironov, I.I.; Zakharov, S.N.

    1984-01-01

    The investigations on evaluation of X-ray radiometric separation of off-grade tin ores of one of the deposits are carried out. The experiments have been performed at loboratory and pilot-commerical plants. 241 Am has been used as a radiation source. In the course of facility commercial the ore has been separated by means of a device comprising a separator and gate separatin device. The results of X-ray radiometric separation have shown its high productive efficiency. Concentrates with higher tin content at high extraction from ores are obtained

  3. Natural galvaniv effect when bed-oxidation ore-bearing zone forming

    International Nuclear Information System (INIS)

    Shchetochkin, V.N.; Kislyakov, Ya.M.; Vasil'eva, Eh.G.

    1995-01-01

    Hypothesis of the essential role of natural galvanic process in exogenetic-epigene ore-formation the model of which was elaborated earlier, is grounded. Genetic conjuction of variations near geochemical barrier of redox and acidic-alkaline hydrogeochemical parameters is stated. These variations in total enable to understand the mechanism of formation of infiltration uranium mineralizatiuon, to explain a number of the observed peculiarities of oxidation ore-controlling zoning, and to explain, as well, slightly-expressed concentration of elements-hydrolyzates in uranium ores. 29 refs.; 6 figs.; 3 tabs

  4. The role of post-ore processes in the alteration of infiltrational uranium deposits

    International Nuclear Information System (INIS)

    Kondrat'eva, I.A.; Bobrova, L.L.; Nesterova, M.V.

    1992-01-01

    Ore-bearing rocks and ores of uranium deposits that are associated with gray alluvial deposits and formed through oxidation of sedimentary beds at the end of the Jurassic, have undergone intensive alterations. The impact of hot carbonic acid solutions on infiltrational uranium deposits, along with calcite and hematite, resulted in partial dissolution of and redeposition of uranium. Uranium concentrates with newly formed Fe-bisulfides and hydroxides in the reducing stage of epigenetic alterations within a hydrochemical sulfide-gley medium, leading to changes in ore morphology. 20 refs., 7 figs., 3 tabs

  5. Development of Technology for Enrichment of Silver Containing Ores

    Science.gov (United States)

    Shekiladze, Asmati; Kavtelashvili, Otari; Bagnashvili, Mamuka

    2016-10-01

    The progress of Georgian economics is substantially associated with a development of new deposits of mineral resources. Among them is the David-Gareji deposit where at present the intensive searching geological works are performed. The work goal involves the elaboration of the technology for processing of silver-containing quartz-barite ores. Without its development the mining of more valuable gold-polymetallic ores is impossible. Because of ore complexity silver and barite are considered in a common technological aspect. The investigations were carried out on the representative samples of quartz-barite ores containing 78-88 g/ton of silver and 27-29 % of silver is a nugget in the form of the simple sulphides and chlorides. The ore is characterized by fine coalescence of barite and ore-generating minerals. Non-ferrous metals haven't any industrial value because of their very low content. Therefore, for the processing of the ores under study the direct selective scheme of flotation enrichment was chosen and the formula of optimal reagent regime was elaborated. Potassium xanthogenate is used as a collector for flotation of silver minerals and pine oil- as a foaming agent. The effect of the pulp - pH and medium temperature on silver flotation was studied. It was established that the silver is actively floats in neutral medium. For barite flotation the various collectors were tested: sulfidezid cotton oil-soap stock, soaps of fatty acids and alkyl sulphates of C12 - C16 row, among the “Baritol” is the most efficient one. Depression of the barren rock was carried out by liquid glass in alkaline medium. The effect of pulp pH on barite flotation has been investigated. The best results were obtained at pH=8.5. The increase of the pulp alkalinity has no essential effect on the indexes of the barite enrichment. Conditional concentrate of the barite is obtained by two fold purification of the main flotation concentrate by the addition of the liquid glass to the re

  6. Radioactivity of Ore Sites of Lead, Zinc and Phosphate in Serbia

    International Nuclear Information System (INIS)

    Todorovic, D.; Jankovic, M.; Nikolic, J.; Kosutic, D.

    2011-01-01

    Natural resources such as ores contain radioactive nuclides at various concentrations. Therefore it is important to investigate the radioactivity in these resources as well as in the soil at the locations of ore deposits. For that reason we conducted preliminary measurements in the soil samples taken from the locations of lead and zinc ore deposits (Bosilegrad and Raska) and from the locations of phosphate ore deposits of phosphate (Bosilegrad). The activity concentrations of radionuclides in soil samples were determined by gamma spectrometry (HPGe detector, relative efficiency 23 %). Results showed the presence of natural radionuclides 226Ra, 232Th, 40K, 235U, 238U as well as the produced radionuclide 137Cs (from the Chernobyl accident). Ambient gamma radiation dose rate in ground level air was also measured. (author)

  7. 36Cl production in situ, and groundwater transport in a uranium ore deposit

    International Nuclear Information System (INIS)

    Cornett, R.J.; Andrews, H.R.; Brown, R.M.; Chant, L.A.; Cramer, J.; Davies, W.G.; Greiner, B.F.; Imahori, Y.; Koslowsky, V.T.; McKay, J.W.; Milton, G.M.; Milton, J.D.C.

    1992-01-01

    The authors have used AMS to measure 36 Cl concentrations produced in situ in ore and in groundwater within the 1.3 billion year old Cigar Lake uranium ore deposit. 36 Cl concentrations are up to 300 times higher in the ore zone than in the surrounding aquifer. Based on 36 Cl ingrowth, the authors calculate the residence time of water within the ore zone to be 100,000 to 300,000 years. Since the geologic setting of this deposit is a very close natural analogue to a proposed nuclear fuel waste repository, this analysis demonstrates that natural geological barriers can effectively isolate mobile radionuclides from an open, regional groundwater flow system over millennia

  8. Underground bioleaching: extracting from low-grade ore

    International Nuclear Information System (INIS)

    McCready, R.G.L.

    1986-01-01

    In 1984, Denison Mines began a research and demonstration project on the engineering aspects of bacterial leaching of low-grade uranium ore at Elliot Lake. The leaching solution was acidic mine water enriched in bacterial nutrients and innoculated with Thiobacillus ferrooxidans. Leaching of one stope was found to be impeded by fungi of the genus penicillium. Although fungal growth on leaching stopes must be prevented, research is proceeding on the potential use of the fungi to concentrate uranium from bioleaching solutions

  9. Bacteria heap leaching test of a uranium ore

    International Nuclear Information System (INIS)

    Liu Hui; Liu Jinhui; Wu Weirong; Han Wei

    2008-01-01

    Column bioleaching test of a uranium ore was carried out. The optimum acidity, spraying intensity, spray-pause time ratio were determined. The potential, Fe and U concentrations in the leaching process were investigated. The effect of bacteria column leaching was compared with that of acid column leaching. The results show that bacteria column leaching can shorten leaching cycle, and the leaching rate of uranium increases by 9.7%. (authors)

  10. A study of VMS ore deposits by the proton microprobe

    International Nuclear Information System (INIS)

    Huston, D.L.; Large, R.R.; Bottril, R.S.; Sie, S.H.; Ryan, C.G.

    1991-01-01

    As part of studies into the mineralogical distribution of gold in volcanogenic massive sulfide (VMS) ore deposits PIXE analysis by the proton microprobe has been used to determine the gold content of pyrite and arsenopyrite from the Rosebery, Mt. Chalmers and Mt. Lyell deposits. In addition, the concentrations of Co, Ni, Cu, Zn, As, Sr, Y, Zr, Mo, Ag, Sb, Te, Au, Tl, Pb and Bi were also determined. 4 refs., 1 tab

  11. THE SOLUBILITY OF MILAS BAUXITE ORE IN SULPHURIC ACI

    Directory of Open Access Journals (Sweden)

    Mustafa GULFEN

    2001-06-01

    Full Text Available The effects of calcination conditions,sulphuric acid concentrations and dissolvingtemperature and period as parameters to thesolubility of the bauxite ore from Gobekdagı reservesin Mugla-Milas region were investigated. The bauxitesamples were calcined in different periods at differenttemperatures. Then the solubility of the calcinedbauxite samples in sulphuric acid solution wasexamined. Dissolving activation energy (Ea wascalculated using the optimum kinetics equation andthe results obtained from the solubility studiesexamined dissolving temperatures and periods

  12. The separation and determination of trace elements in iron ore

    International Nuclear Information System (INIS)

    Jones, E.A.

    1977-01-01

    The separation, concentration, and determination of trace elements in iron ores are described. After the sample has been dissolved, the iron is separated by liquid-liquid extraction with a liquid cation-exchanger, di-(2-ethylhexyl) phosphoric acid. The trace elements aluminium, cadmium, calcium, chromium, cobalt, copper, lead, magnesium, manganese, mercury, potassium, sodium, vanadium, and zinc are determined in the aqueous phase by atomic-absorption spectrophotometry

  13. Infrared detection of ore variability that influences the environmental risks during perlite mining and processing

    OpenAIRE

    Guatame Garcia, L.A.; Buxton, M.W.N.

    2017-01-01

    In the mining of perlite deposits, controlling the generation of fine particles and the concentration of metals is of outstanding importance to meet the environmental and market requirements. Particle size and chemical purity are conventionally manipulated during the processing of the ore to achieve high product specifications. However, the current practices do not consider a proactive approach that focuses in the in-pit characterisation of the ore that would minimise the environmental impact...

  14. Uranium Rirang ore processing: extraction of uranium from Rirang ore digestion solution with tributyl phosphate

    International Nuclear Information System (INIS)

    Arief, E. R.; Zahardi; Susilaningtyas

    1998-01-01

    Uranium is extracted from Rirang ore acid digestion solution containing rare earths. A mixture of tributyl phosphate solvent and kerosene diluent is employed. Several parameters of solvent extraction have been studied included aqueous to organic phase ratio, H 2 O 2 reductor concentration and Tbp concentration in the solvent mixture, as well as the aqueous to organic phase ratio in the stripping process. The optimum conditions for the extraction step include the use of 25% H 2 O 2 (v/v), one to one aqueous to organic ratio, and 40% Tbp in kerosene. The extraction recovery for U, RE, Th, and PO 4 3 - are 99%, 4%, 70%, and 30%, respectively. The stripping step optimum conditions include the use of one to five organic to aqueous phase ratio 0.24 N HNO 3 . and the stripping recovery for U, RE, Th, and PO 4 3 - are 84%, 80%, 72%, and 83%, respectively

  15. Intensification of the Reverse Cationic Flotation of Hematite Ores with Optimization of Process and Hydrodynamic Parameters of Flotation Cell

    Science.gov (United States)

    Poperechnikova, O. Yu; Filippov, L. O.; Shumskaya, E. N.; Filippova, I. V.

    2017-07-01

    The demand of high grade iron ore concentrates is a major issue due to the depletion of rich iron-bearing ores and high competitiveness in the iron ore market. Iron ore production is forced out to upgrade flowsheets to decrease the silica content in the pelettes. Different types of ore have different mineral composition and texture-structural features which require different mineral processing methods and technologies. The paper presents a comparative study of the cationic and anionic flotation routes to process a fine-grain oxidized iron ore. The modified carboxymethyl cellulose was found as the most efficient depressant in reverse cationic flotation. The results of flotation optimization of hematite ores using matrix of second-order center rotatable uniform design allowed to define the collector concentration, impeller rotation speed and air flowrate as the main flotation parameters impacting on the iron ore concentrate quality and iron recovery in a laboratory flotation machine. These parameters have been selected as independent during the experiments.

  16. Management of wastes containing radioactivity from mining and milling of uranium ores in Northern Australia

    International Nuclear Information System (INIS)

    Costello, J.M.

    1977-01-01

    The procedures and controls to achieve safe management of wastes containing radioactivity during the mining and processing of uranium ores are mainly site specific depending on the nature, location and distribution of the ore and gangue material. Waste rock and below-ore-grade material containing low levels of radioactivity require disposal at the mine site. In open cut mining the material is generally stockpiled above ground, with revegetation and collection of run-off water. Some material may be used to backfill open cuts. Management of these wastes requires a thorough investigation of ground water hydrology and surface soil characteristics to control dissipation of radioactive material. Dust containing radon and radioactive particulate is produced during ore milling, and dusts of ore concentrate are generated during calcination and packaging of the yellowcake product. These dusts are managed by ventilation and filtration systems, working conditions, and discharges to atmosphere will be according to the Australian Code of Practice on Radiation Protection during Mining and Milling of Uranium Ores. The chemical waste stream from leaching and processing of the uranium ores contains the majority of the radioactivity resulting from radium and its decay products. Neutralised effluent is discharged into holding ponds for settling of solids. This paper describes the nature of wastes containing radioactivity resulting from the mining and milling of uranium, and illustrates modern engineering practices and monitoring procedures to manage the wastes, as described in the Environmental Impact statement produced by Ranger Uranium Mines Proprietary Limited for public hearings

  17. Lacustrine-humate model for primary uranium ore deposits, Grants Uranium Region, New Mexico

    International Nuclear Information System (INIS)

    Turner-Peterson, C.E.

    1985-01-01

    Two generations of uranium ore, primary and redistributed, occur in fluvial sandstones of the Upper Jurassic Morrison Formation in the San Juan basin; the two stages of ore formation can be related to the hydrologic history of the basin. Primary ore formed soon after Morrison deposition, in the Late Jurassic to Early Cretaceous, and a model, the lacustrine-humate model, is offered that views primary mineralization as a diagenetic event related to early pore fluid evolution. The basic premise is that the humate, a pore-filling organic material closely associated with primary ore, originated as humic acids dissolved in pore waters of greenish-gray lacustrine mudstones deposited in the mud-flat facies of the Brushy Basin Member and similar K shale beds in the Westwater Canyon Member. During compaction associated with early burial, formation water expelled from lacustrine mudstone units carried these humic acids into adjacent sandstone beds where the organics precipitated, forming the humate deposits that concentrated uranium. During the Tertiary, much later in the hydrologic history of the basin, when Jurassic sediments were largely compacted, oxygenated ground water flowed basinward from uplifted basin margins. This invasion of Morrison sandstone beds by oxidizing ground waters redistributed uranium from primary ores along redox boundaries, forming ore deposits that resemble roll-front-type uranium ores. 11 figures

  18. Management of wastes containing radioactivity from mining and milling uranium ores in Northern Australia

    International Nuclear Information System (INIS)

    Costello, J.M.

    1977-01-01

    The procedures and controls to achieve safe management of wastes containing radioactivity during the mining and processing of uranium ores are mainly site-specific depending on the nature, location and distribution of the ore and gangue material. Waste rock and below-ore-grade material containing low levels of radioactivity require disposal at the mine site. In open-cut mining the material is generally stockpiled above ground, with revegetation and collection of run-off water. Some material may be used to backfill open cuts. Management of these wastes requires a thorough investigation of groundwater hydrology and surface soil characteristics to control dissipation of radioactive material. Dust containing radon and radioactive particulate is produced during ore milling, and dusts of ore concentrate are generated during calcination and packaging of the yellowcake product. These dusts are managed by ventilation and filtration systems; working conditions and discharges to atmosphere will be according to the Australian Code of Practice on Radiation Protection during Mining and Milling of Uranium Ores. The chemical waste stream from leaching and processing of the uranium ores contains most of the radioactivity resulting from radium and its decay products. Neutralized effluent is discharged into holding ponds for settling solids. The paper describes the nature of wastes containing radioactivity resulting from the mining and milling of uranium, and illustrates modern engineering practices and monitoring procedures to manage the wastes, as described in the Environmental Impact Statement produced by Ranger Uranium Mines Pty Ltd (RUM) for public hearings. (author)

  19. Acid leaching of oxide-sulphide copper ore prior the flotation: A way for an increased metal recovery

    Directory of Open Access Journals (Sweden)

    Sokić Miroslav D.

    2015-01-01

    Full Text Available Copper mine "Cerovo"- East Serbia as well as the other ore bodies in its vicinity contain a significant amount of oxide copper minerals in their uper layers (>40%. Processing of such mixed ores by the existing concentration technologies leads to a substantial copper losses (<60%. Reduction of "oxide copper", by acid leaching prior the flotation concentration, can increase the overall copper efficiency up to more than 70% in the single-stage leaching, achieving an efficiency in the flotation concentration stage higher than 75%. Based on the performed experimental results the flow sheet for processing of the mixed oxide-sulphide copper ore is proposed.

  20. Investigation of the degree of equilibrium of the long-lived uranium-238 decay-chain members in airborne and bulk uranium-ore dusts

    International Nuclear Information System (INIS)

    Jackson, P.O.; Thomas, C.W.

    1982-08-01

    The degree of disequilibrium among 238 U decay chain members in some airborne dusts and typical ores has been established by precise radiochemical analyses. This information is necessary to evaluate the lung dose model currently used for estimating the effect of the inhalation of uranium ore dust. The particle size distributions of airborne decay chain components in dusts at one uranium mill have been investigated. Statistically significant disequilibria were observed for 230 Th, 226 Ra, and 210 Pb in both airborne dusts and composite ore samples. With the exception of ore from one mill in the United States, most of the daughter concentrations in powdered ore composites were within 10% of 238 U. In airborne dusts, the concentration of 226 Ra was typically below 238 U; the minimum 226 Ra concentration observed for airborne ore dusts was 56% of equilibrium. A statistically significant particle size dependence was observed for 226 Ra/ 238 U ratios in several airborne dusts collected at a uranium mill

  1. New interpretation of the dominant ore-controlling factor of the uranium ore field No. 322

    International Nuclear Information System (INIS)

    Liu Xiang; Yang Chongqiu

    1996-01-01

    The NE-trending fault structures in ore field NO. 322 are characterized by compress-shearing, left-Lateral left-slipping, having an obvious control over the Localisation of the ore field No. 322, and are the dominant ore-controlling factor of the ore field NO.322. Resulting from the sinistral displacement of the NE-trending fault, there is a pull-apart basin in the Feng Zhou area. The formation and evolution of the NE-trending fault zone and the Feng Zhou basin control the formation of uranium deposits of ore field No. 322

  2. Iron from Zealandic bog iron ore -

    DEFF Research Database (Denmark)

    Lyngstrøm, Henriette Syrach

    2011-01-01

    og geologiske materiale, metallurgiske analyser og eksperimentel arkæologiske forsøg - konturerne af en jernproduktion med udgangspunkt i den sjællandske myremalm. The frequent application by archaeologists of Werner Christensen’s distribution map for the occurrence of bog iron ore in Denmark (1966...... are sketched of iron production based on bog iron ore from Zealand....

  3. PGAA method for control of the technologically important elements at processing of sulfide ores

    International Nuclear Information System (INIS)

    Kurbanov, B.I.; Aripov, G.A.; Allamuratova, G.; Umaraliev, M.

    2006-01-01

    Full text: Many precious elements (Au, Re, Pt, Pd, Ag, Cu, Ni, Co, Mo) in ores mainly exist in the form of sulfide minerals and the flotation method is often used for processing of such kind of ores. To enhance the efficiency of the process it is very important to carry out the operative control of the elements of interest at various stages of ore processing. In this work the results of studies for developing methods for control of technologically important elements at processing and enrichment sulfide ores, which content the gold, copper, nickel, molybdenum in the ore-processing plants of Uzbekistan. The design of transportable experimental PGAA device on the basis of low-power radionuclide neutron source ( 252 Cf) with neutrons of 2x10 7 neutr/sec allowing to determine element content of the above named ores and their processing products is offered. It is shown that the use of the thermal neutron capture gamma-ray spectrometry in real samples and technological products allows prompt determination of such elements as S, Cu, Ti and others, which are important for flotation of sulfide ores. Efficiency control of the flotation processing of sulfide ores is based on quick determination of the content of sulfur and some other important elements at different stages of the process. It was found that to determine elements the following gamma lines are the most suitable - 840.3 keV for sulfur, 609 keV and 7307 keV for copper and 1381.5 keV, 1498.3 keV and 1585.3 keV for titanium. Based on the measurements of original ores, concentrates of various stages of flotation and flotation slime the possibility for prompt determination of S, Cu and Ti content and thus to get necessary information on the efficiency of the flotation process was shown. (author)

  4. Beneficiation and leaching study of a muti-Au carrier and low grade refractory gold ore

    Science.gov (United States)

    Li, W. J.; Song, Y. S.; Chen, Y.; Cai, L. L.; Zhou, G. Y.

    2017-09-01

    Detailed mineralogy and beneficiation and leaching study of a muti-Au carrier, low grade refractory gold ore from a beneficiation plant in Henan Province, China, was investigated. Mineral liberation analysis, scanning electron microscopy, element phase analysis and etc. by a mineral liberation analyser were used for mineralogical characterization study of this ore. The present work describes an experimental study on the effect of traditional parameters (such as grinding fineness and reagent regimes), middling processing method and flowsheet construction on the total recovery and the assay of the floatation concentrate. Two-step floatation and part of middling combined to the floatation tailing for gold leaching process resulted in high gold grade (g.t-1) and gold recovery (%) for this refractory gold ore. This process opens the possibilities of maximizing Au grade and recoveries in a muti-Au carrier and low grade refractory gold ore where low recoveries are common.

  5. Flotation-nitric acid leach procedure for increasing uranium recovery from a refractory ore

    International Nuclear Information System (INIS)

    Carnahan, T.G.; Lei, K.P.V.

    1979-01-01

    The Bureau of Mines investigated a flotation-nitric acid leach procedure as part of the goal to maximize minerals and metals recovered from primary and secondary domestic resources. Studies were conducted on an ore that contained carbon-bearing and sulfide mineralization that rendered a portion of the ore refractory (resistant) to conventional leaching technology. The procedure investigated for treating the ore consisted of the following: (1) separation by flotation of the carbonaceous and sulfidic components from the ore, (2) leaching the flotation concentrate with nitric acid at 100 0 to 110 0 C, (3) leaching the flotation tailings with sulfuric acid, and (4) processing the combined leached slurries in a conventional manner to recover yellow cake. In step 2, HNO 3 is converted to gaseous products from which it is regenerated by reacting these products with air and water for further leaching. An overall uranium extraction of 96% was achieved by this procedure

  6. Dolochar as a reductant in the reduction roasting of iron ore slimes

    Science.gov (United States)

    Rath, Swagat S.; Rao, Danda Srinivas

    2017-12-01

    The present investigation examines the viability of dolochar, a sponge iron industry waste material, as a reductant in the reduction roasting of iron ore slimes, which are another waste generated by iron ore beneficiation plants. Under statistically determined optimum conditions, which include a temperature of 900°C, a reductant-to-feed mass ratio of 0.35, and a reduction time of 30-45 min, the roasted mass, after being subjected to low-intensity magnetic separation, yielded an iron ore concentrate of approximately 64wt% Fe at a mass recovery of approximately 71% from the feed iron ore slime assaying 56.2wt% Fe. X-ray diffraction analyses indicated that the magnetic products contain magnetite and hematite as the major phases, whereas the nonmagnetic fractions contain quartz and hematite.

  7. [Biooxidation of gold-bearing sulfide ore and subsequent biological treatment of cyanidation residues].

    Science.gov (United States)

    Kanaev, A T; Bulaev, A G; Semenchenko, G V; Kanaeva, Z K; Shilmanova, A A

    2016-01-01

    The percolation biooxidation parameters of ore from the Bakyrchik deposit were studied. An investigation of the technological parameters (such as the concentration of leaching agents, irrigation intensity, and pauses at various stages of the leaching) revealed the optimal mode for precious metal extraction. The stages of the ore processing were biooxidation, gold extraction by cyanidation or thiosulfate leaching, and biological destruction of cyanide. The gold and silver recovery rates by cyanidation were 64.0 and 57.3%, respectively. The gold and silver recovery rates by thiosulfate leaching were 64.0 and 57.3%, respectively. Gold and silver recovery rates from unoxidized ore (control experiment) by cyanidation were 20.9 and 26.8%, respectively. Thiosulfate leaching of unoxidized ore allowed the extraction of 38.8 and 24.2% of the gold and silver, respectively. Cyanidation residues were treated with bacteria of the genus Alcaligenes in order to destruct cyanide.

  8. Treatment of waste water from uranium ore preparation

    International Nuclear Information System (INIS)

    Klicka, V.; Mitas, J.; Vacek, J.

    1976-01-01

    An improved closed-loop process is described for treating waste water resulting from chemical extraction of uranium from ore. The water is evaporated to form a concentrated solution and is then subjected to crystallization of the least soluble salt component thereof via further evaporation, or cooling or simultaneous cooling and a partial vacuum. The crystallized component is then separated from the mother liquor, whereupon the latter is fed back after removal of residual uranium therefrom to the extraction installation to replace the acids used therein. Additionally, the pure condensate produced during evaporation of the waste waters is employed as a replacement for the fresh water employed in processing of the ore. 6 claims, 2 figures

  9. Rirang Uranium Ore Processing System Design: Agitated Digester

    International Nuclear Information System (INIS)

    Erni, R.A.; Susilaningtyas

    1996-01-01

    A closed tank digester equipped with a pitched blades turbine agitator has been designed to facilities Rirang uranium ore dissolution using concentrated sulphuric acid at high temperature. The digester was designed to accommodate the digestion of 6 kg of-65 mesh ore at 200 o C, acid resistant material (SS-3 16). It has the dimension of 33 cm high, 22 cm diameter, and elliptical bottom and height of 4 cm. Moreover, the dimension of the 4 blades agitator is as follows: 8 cm long, 1,6 cm blades width. The distance between the blades and digester required 0, 007 Hp for a 500 rpm agitation speed and + 24. 103 kcal energy equipment for heating. Digestion experiment using the agitated digester yielded data that are in good agreement with laboratory scale experiment

  10. Nickel Ore Dispersion Evaluation and Consequences in Flotation Process

    Science.gov (United States)

    de São José, Fábio; Imbelloni, Alaine Moreira; Nogueira, Francielle Câmara; Pereira, Carlos Alberto

    2016-04-01

    Nickel ore dispersion before flotation using different reagents was investigated on a bench scale to improve metallurgical recovery and selectivity. The nickel ore had a content of 0.8 pct nickel and 14.5 pct MgO. A positive linear correlation between MgO and Ni was found. Carboxy methyl cellulose, both pure and combined with Na2CO3, was the best dispersant used. The most efficient collector was potassium amyl xanthate combined with mercaptobenzothiazole, and the addition of xanthate was decisive for this good result because it is normally more stable in the pH range used in the tests. A pH change from 7 to 9 resulted in a metal recovery increase of 49.3 pct, together with an increase of 6.25 pct of MgO in the concentrate.

  11. Direct Reduction of Iron Ore

    Science.gov (United States)

    Small, M.

    1981-04-01

    In the search for a pure, available iron source, steelmakers are focusing their attention on Directly Reduced Iron (DRI). This material is produced by the reaction of a low gangue iron ore with a hydrocarbonaceous substance. Commercially, DRI is generated in four different reactors: shaft (moving-bed), rotary kiln, fluidized bed, and retort (fixed-bed). Annual worldwide production capacity approaches 33 million metric tons. Detailed assessments have been made of the uses of DRI, especially as a substitute for scrap in electric furnace (EF) steelmaking. DRI is generally of a quality superior to current grades of scrap, with steels produced more efficiently in the EF and containing lower levels of impurities. However, present economics favor EF steel production with scrap. But this situation could change within this decade because of a developing scarcity of good quality scrap.

  12. Production of Schwarzmoeller briquets from weakly caking black coal and iron ore

    Energy Technology Data Exchange (ETDEWEB)

    Naundorf, W.

    1986-01-01

    Laboratory production is explained of coal and iron ore briquets suitable for metallurgy, using type 33 weakly caking black coal, iron ore concentrates from 3 Soviet mines and sulfite lye as binder. Coal and ore were finely ground to 0.3/0.0 mm grain size, briquetted at high pressure of 150 MPa and at 80 C temperature. The sulfite lye binder content ranged from 4 to 10% in the briquet mixture. Briquets were thermally treated up to 1000 C; the resulting coke lumps (Schwarzmoeller briquets) were analyzed for compression and abrasion strength. Detailed graphs of briquet and coke lump quality parameters are provided. The study shows that high quality metallurgical coke lumps are obtained by briquetting mixtures of black coal and iron ore in a mixture of about 70:30 with 4 to 9% addition of sulfite binder. Compression strength of coke lumps exceeded 35 MPa. The minimum black coal-iron ore mass relation for producing metallurgical coke lumps was 30:70 using 2 types of iron ore concentrates. The influence of adding limestone to the briquetting mixture and of coking conditions resembling the horizontal chamber oven process is also investigated. 5 references.

  13. Radioisotope devices at Novo-Krivorozhskij-ore-enrichment plant

    International Nuclear Information System (INIS)

    Levitskij, V.Ya.; Kucher, V.G.; Ministerstvo Chernoj Metallurgii Ukrainskoj SSR, Dnepropetrovsk, Bazovaya Opytno-Konstruktorskaya Izotopnaya lab.)

    1975-01-01

    Use of the ''Ferrite'' analyzers, AZhR and PAZh-1 and the GR-7 gamma relay in different engineering areas of the Novo-Krivorozh ore-enrichment plant is evaluated. The ''Ferrite'' radioisotopic analyzer was designed for rapid roentgeno-radiometric determination of the total iron and iron group element contents in powdered samples of ores and products of their treatment. From the density of the flux of the characteristic radiation it is possible to determine quantitatively the content of the element of interest in the analyzed material. The radioisotpic analyzer AZhR-1 is distinguished by its high efficiency in the analysis for total iron on products of processing of iron ore raw materials. The use of this apparatus allows complete replacement of the chemical method for rapid analysis of concentrates by the roentgeno-radiometric method, which decreases the total analytical work on determination of total iron and speeds up output of information on concentrate quality. The radioisotopic gamma analyzer PAZh-1 is designed for automatic and either continuous or discrete measurement of the total iron content in iron ore materials ground to 50 mm, carried on a conveyor, without selection or preparation of the samples for analysis. The analyzer operates on the principle of measuring the average frequency of impingement on a detector of gamma quanta back-scattered by the analyzed material. This frequency is determined by the percentage content of total iron in the material. The apparatus operates continuously. The mean square deviation of the apparatus values from chemical data is 0.93% Fesub(total). Use of the apparatus greatly increases the operativeness of the control and decreases the laboriousness of raw material sampling in an engineering stream. The radioisotopic data units GR-7 are designed for control of the level of materials in hoppers for recovery and burning of agglomerates. Use of this apparatus showed its great advantage over data units of other types

  14. Up-gradation of MoO{sub 3} and separation of copper, iron, zinc from roasted molybdenum ore by a leaching process

    Energy Technology Data Exchange (ETDEWEB)

    Jin-Young, Lee; Jyothi Rajesh, Kumar; Ho-Seok, Jeon; Joon-Soo, Kim, E-mail: rajeshkumarphd@rediffmail.com, E-mail: rkumarphd@kigam.re.kr [Extractive Metallurgy Department, Mineral Resources Research Division, Korea Institute of Geoscience and Mineral Resources (KIGAM) (Korea, Republic of)

    2013-04-15

    The present research paper deals with the oxidation process of molybdenum ore. The main target of the present study is the up-gradation of MoO{sub 3} from roasted molybdenum ore by a leaching process without waste generation. The most important application of hydrometallurgical processing is the leaching process of the ore and it is the primary process to make pure metal from ore. The present investigations optimize the following experimental parameters to improve the concentration of MoO{sub 3} as well as the separation of copper, iron and zinc in roasted molybdenum ore: effect of acid concentration, temperature, pulp density and leaching time were studied systematically. The temperature study was carried out at 550-595 Degree-Sign C for the oxidation process. The XRD result shows that oxidation process of molybdenum ore and SEM pictures were taken for particles before and after the oxidation process at 585 Degree-Sign C for 360 min. (author)

  15. Growth characteristics of a strain of iron-oxidizing bacterium and its application in bioleaching of uranium ores

    International Nuclear Information System (INIS)

    Zhang Rui; Liu Yajie; Gao Feng; Xu Lingling

    2008-01-01

    05B is a strain of iron-oxidizing bacterium which separated from a uranium ore. The effect of temperature, initial pH, inoculation amount and initial total iron concentration on the strain's growth and activities in bioleaching of uranium ores are studied. The results show that the optimum growth temperature is 40-45 degree C, the optimum inoculation pH value being 1.5-1.7, the optimum initial inoculation amount being 10%-20%, and the initial total iron concentration being not more than 5 g/L. 05B is fit for leaching of low grade uranium ores. (authors)

  16. Floatability study of graphite ore from southeast Sulawesi (Indonesia)

    Science.gov (United States)

    Florena, Fenfen Fenda; Syarifuddin, Fahmi; Hanam, Eko Sulistio; Trisko, Nici; Kustiyanto, Eko; Enilisiana, Rianto, Anton; Arinton, Ghenadi

    2016-02-01

    Graphite ore obtained from Kolaka Regency, South East Sulawesi, Indonesia have been succesfully investigated for beneficiation by froth flotation technique. Preliminary study have been done to determine the minerals types, fixed carbon content and liberation size of the graphite. Graphite is naturally floatable due to its hydrophobic property. Some suitable reagents are usually added to increase effectiveness of recovery. In this article, enrichment of graphite by froth flotation was studied by investigating the effect of reagents concentrations, rotation speed and particle size on the carbon grade and recovery of the concentrate. The carbon grade increased from 3.00% to 60.00% at the optimum flotation conditions.

  17. Vanadium-bearing titaniferous iron ores from the Rooiwater, Usushwana, Mambula, Kaffirskraal, and the Trompsburg igneous complexes

    International Nuclear Information System (INIS)

    Reynolds, A.M.

    1979-01-01

    The mineralogy and chemistry of some vanadium-bearing titaniferous iron ores from a number of smaller South African basic intrusions are reported, and an assessment is given of the potential of these ores for use as raw materials in the production of iron, high-titania slag, and vanadium pentoxide. The ores from each complex can be distinguised readily on the basis of their chemical composition and textural relations. The Rooiwater Complex represents the most promising area. It contains two layers of titaniferous magnetite, each approximately 8 m thick, in the eastern part, the lowest seam being chemically similar to the economically important main layer of titaniferous magnetite in the Bushveld Complex. The ores are silicate-poor and consist largely of multi-phase titaniferous-magnetite grains containing modified ilmenite and pleonaste micro-intergrowths. The coarse grain size of these ores favours beneficiation, and they can be partially treated to yield ilmenite concentrates and low-titania magnetite fractions in which the content of vanadium pentoxide is higher than that in the original ores. The Mambula ores are silicate-rich and would require extensive beneficiation. The Kaffirskraal ores consist of multi-phase grains of titaniferous magnetite containing crystallographically oriented ilmenite, ulvospinel, and pleonaste micro-intergrowths. Minor coarser-grained ilmenite is also present. The Usushwana ores are texturaly similar but contain abundant lamellar ilmenite in place of the ulvospinel. The ores from these two complexes cannot be beneficiated by conventional ore-dressing techniques, and would require direct metallurgical treatment for the recovery of iron, titania, and vanadium pentoxide [af

  18. Modelling a uranium ore bioleaching process

    International Nuclear Information System (INIS)

    Chien, D.C.H.; Douglas, P.L.; Herman, D.H.; Marchbank, A.

    1990-01-01

    A dynamic simulation model for the bioleaching of uranium ore in a stope leaching process has been developed. The model incorporates design and operating conditions, reaction kinetics enhanced by Thiobacillus ferroxidans present in the leaching solution and transport properties. Model predictions agree well with experimental data with an average deviation of about ± 3%. The model is sensitive to small errors in the estimates of fragment size and ore grade. Because accurate estimates are difficult to obtain a parameter estimation approach was developed to update the value of fragment size and ore grade using on-line plant information

  19. Improved leaching process for metal ores

    International Nuclear Information System (INIS)

    Kar-Kwan Yung, K.; Barlow, C.B.; Glass, J.R.

    1980-01-01

    The general overall sequence of process steps in the technique of the invention in set forth. In sequence, the ore is crushed, and solubilizing reagents and moisture are added to the crushed ore in preselected controlled portions. The mixture of ore, reagent, and moisture is then cured followed in the preferred process by conditioning for filtration. The slurry that is produced from conditioning is then subjected to multiple stage washing on a belt filter. The filtrate is further processed for metal value recovery and the solids are transported to tailings disposal

  20. Direct Flotation of Niobium Oxide Minerals from Carbonatite Niobium Ores

    Science.gov (United States)

    Ni, Xiao

    Currently the recovery of niobium oxide minerals from carbonatite niobium ores relies on the use of non-selective cationic collectors. This leads to complicated process flowsheets involving multiple desliming and multiple reverse flotation stages, and low niobium recovery. In this research, anionic collectors that are capable of strong chemisorption on the niobium minerals were studied with the objective of directly floating the niobium oxide minerals from the carbonatite ores. In the flotation of both high purity minerals and Niobec ores, it was shown that the combination of hydroxamic acid and sodium metaphosphate was an effective reagent scheme for the direct flotation of niobium oxide from its ores. Batch flotation on the Niobec Mill Feed showed that over 95% of niobium oxide was recovered into a rougher concentrate that was less than 47% of the original feed mass. Preliminary cleaning tests showed that the reagent scheme could also be used to upgrade the rougher concentrate, although the depression of iron oxide minerals required further study. X-ray photoelectron spectroscopic (XPS) measurement results confirm that OHA (octyl hydroxamic acid) could chemisorb on pyrochlore surface while only physically adsorb on calcite, judging by the chemical shifts of electron binding energies in the elements in both OHA and the mineral surfaces. When hydroxamic acid was adsorbed on calcite surface, the binding energies of the N 1s electrons, at 400.3 eV, did not shift. However, after adsorption on pyrochlore, the N 1s binding energy peak split into two peaks, one at a binding energy of around 399 eV, representing chemically adsorbed OHA, the other at between 400 and 401 eV. The experimental data suggested a strong chemisorption of the OHA on pyrochlore surface in the form of a vertical head-on orientation of the OHA molecules so that the pyrochlore was strongly hydrophobized even at low OHA concentrations, followed by possibly randomly oriented physisorbed OHA molecules

  1. Uranium and Molybdenum extraction from a Cerro Solo deposit ore

    International Nuclear Information System (INIS)

    Becquart, Elena T.; Arias, Maria J.; Fuente, Juan C. de la; Misischia, Yamila A.; Santa Cruz, Daniel E.; Tomellini, Guido C.

    2009-01-01

    Cerro Solo, located in Chubut, Argentina, is a sandstone type uranium-molybdenum deposit. Good recovery of both elements can be achieved by acid leaching of the ore but the presence of molybdenum in pregnant liquors is an inconvenient to uranium separation and purification. A two steps process is developed. A selective alkaline leaching of the ore with sodium hydroxide allows separating and recovering of molybdenum and after solid-liquid separation, the ore is acid leached to recover uranium. Several samples averaging 0,2% uranium and 0,1% molybdenum with variable U/Mo ratio have been used and in both steps, leaching and oxidant reagents concentration, temperature and residence time in a stirred tank leaching have been studied. In alkaline leaching molybdenum recoveries greater than 96% are achieved, with 1% uranium extraction. In acid leaching up to 93% of the uranium is extracted and Mo/U ratio in solvent extraction feed is between 0,013 and 0,025. (author)

  2. Uranium ore mill at Dolni Rozinka: 40 years of operation

    International Nuclear Information System (INIS)

    Toman, F.; Jezova, V.

    2007-01-01

    Uranium ore mined in the Rozna deposit is treated at a chemical treatment plant (a mill) situated in the close vicinity of the Rozna mine. In the mill, uranium is extracted from the crushed and ground-up ore by alkaline leaching. Uranium is then recovered from the solution by sorption on ion exchange resin; the next steps are precipitation and drying. Alkaline leaching is applied at the atmospheric pressure and the temperature of 80 deg C; the recovery factor is moving around 93%. The final product of the milling is uranium concentrate, ammonium diuranate (NH 4 ) 2 U 2 O 7 ), a so-called 'yellow cake' which is treated into a fuel for nuclear power plants in conversion facilities abroad. The milling is carried on under the condition of the closed cycle of technology water. Due to the positive annual precipitation balance, the over balance of technology water in tailings pond has to be purified before discharging into a river. Evaporation and membrane processes (electrodialysis and reverse osmosis) are used to purify the water. The mill at Dolni Rozinka has been in operation since 1968. It has processed 13.2 million tons of uranium ore which is about 14000 tons of uranium and purified more than 6 million m 3 of the over balanced technology water during 40 years. From the organizational point of view, the mine and the chemical treatment plant form the branch plant GEAM, which is a part of the state enterprise DIAMO. (author)

  3. Automation of the second iron ore slurry pipeline from Samarco

    Energy Technology Data Exchange (ETDEWEB)

    Aguilar, Juliana M.; Fonseca, Mario L.; Drumond, Pablo P.; Barbosa, Sylvio [IHM Engenharia, Belo Horizonte, MG (Brazil)

    2009-07-01

    The second iron ore slurry pipeline from Samarco was build to attend the Third Pellet Plant Project, which includes a new Concentration Plant at Germano-MG and a third Pellet Plant at Ubu-ES. It has 396km of extension and links the two plants by pulping the iron ore slurry prepared at Germano Unit. This works aims to present the iron ore slurry pipeline with emphasis on the automation architecture for the supervision and control system, interconnect throughout the pipe extension by fiber optics. The control system is composed of ControlLogix CLP's at the pulping and valve station and Micrologix CLP's at the pressure and cathodic protection monitoring points, totalizing 19 PLC's. The supervisory system was developed using the Wonderware IAS 3.0 suite, including the supervisory software InTouch 9.5 and the integrated ArchestrA IDE, and is composed of two data servers in redundancy and nine operation stations. The control and supervision system is interconnect through and Ethernet network using fiber optics and multiplexer modules (GE JungleMux) for voice, data and video. Among the expected results, it can be highlighted the sequence automation, greater process data availability (real and historical) and greater facility for the operation and detection of failures. (author)

  4. Uranium R and D directed to low-grade ores

    International Nuclear Information System (INIS)

    Anon.

    1976-01-01

    The treatment of depleted uranium ores by in-situ leaching and by counterflow ion exchange in the USA is described. In-situ leaching is mainly suitable for sandstone deposits. The research was originally focused on leaching with an acid and with carbonates. Phosphoric acid appears to be a promising leaching agent. The equipment for continuous ion exchange may be used for sludge processing but the application depends on the type of equipment and mineralogy of processed ores. The method is advantageous for lower capital costs and for smooth operation. Ion exchange is also used for uranium extraction from mine waters in the USA as well as in Canada. For example, in Grants, New Mexico, a yield exceeding 90% was reached in mine waters only containing 5 to 7 ppm U 3 O 8 . In the future, the treatment of ores with a low uranium content will require more selective extraction methods in view of the more stringent technical conditions of uranium concentrate processing. (J.P.)

  5. Radioisotopes investigations of copper ore dressing processes

    International Nuclear Information System (INIS)

    Petryka, L.; Furman, L.; Przewlocki, K.; Stegowski, Z.

    1992-01-01

    This paper describes radioisotope applications in the copper industry, mainly for the examination of comminution, classification, and flotation processes for selected physical parameters. Measurements were performed by a mobile laboratory containing the electronics for experiment control and data recording and processing using special computer software. This system makes it possible to determine measurements in an industrial environment. The data acquisition system provides 24 spectrometric channels, consisting of scintillation probes, high-voltage (HV) power supplies, and pulse-height analyzers, as well as an analog-to-digital (A/D) converter interfaced to the IBM personal computer. The sampling time is fully programmable and interrupt based and can vary from 1 ms to hours and may be set separately for each channel. The milli-second sampling time technique has been applied to high-resolution flow velocity measurements. On the other hand, longer sampling time enables the system to be left unattended for days to monitor, for example, copper ore concentration or efficiency of the flotation process

  6. Uranium ore deposits: geology and processing implications

    International Nuclear Information System (INIS)

    Belyk, C.L.

    2010-01-01

    There are fifteen accepted types of uranium ore deposits and at least forty subtypes readily identified around the world. Each deposit type has a unique set of geological characteristics which may also result in unique processing implications. Primary uranium production in the past decade has predominantly come from only a few of these deposit types including: unconformity, sandstone, calcrete, intrusive, breccia complex and volcanic ones. Processing implications can vary widely between and within the different geological models. Some key characteristics of uranium deposits that may have processing implications include: ore grade, uranium and gangue mineralogy, ore hardness, porosity, uranium mineral morphology and carbon content. Processing difficulties may occur as a result of one or more of these characteristics. In order to meet future uranium demand, it is imperative that innovative processing approaches and new technological advances be developed in order that many of the marginally economic traditional and uneconomic non-traditional uranium ore deposits can be exploited. (author)

  7. Filtration aids in uranium ore processing

    International Nuclear Information System (INIS)

    Ford, H.L.; Levine, N.M.; Risdon, A.L.

    1975-01-01

    The patent describes a process whereby improved flocculation efficiency and filtration of carbonate leached uranium ore pulps are obtained by treating the filter feed slurry with an aqueous solution of hydroxyalkyl guar. (J.R.)

  8. Fe extraction from çayeli copper ores by bioleaching with eco freiendly acidithiobacillus ferrooxidans

    International Nuclear Information System (INIS)

    Kocadagistan, M.E.; Bayhan, Y.K.

    2017-01-01

    Recently, biological treatment; an important recovery process, has became important from the environmental and economical respects in recovery of metallic values from low-grade sulfur-bearing ores or concentrates. Bacterial ore leaching can be applied to extract heavy metals from low grade ores, industrial wastes and other materials on an industrial scale by different procedures. The main objective of this work was to investigate the dissolution of Fe from Çayeli copper ores, via a bioleaching process using Acidithiobacillus ferrooxidans. Experiments performed with batch operation in jar test equipment were conducted at different pH values, pulp densities, inoculum volumes, particle sizes, stirring conditions and operation times. The optimal parameters were found as follows; at pH 2, the pulp density; 4% (w/v), inoculum volume; 4% (v/v), stirring rate; 120 rpm and particle size; -0.053 mm for 192nd and 288th hours, at pH 2, the pulp density; 4% (w/v), inoculum volume; 5% (v/v), stirring speed; 200 rpm and particle size; -0.053 mm for 384th and 480th hours. By performing the bioleaching process under these conditions, almost 99% of the iron extent in the ore was transfer from ore into solution, however the experiments in which distilled water was used instead of modified 9K*, only 18.5% Fe efficiency was obtained. (author)

  9. A New Direction for Biomining: Extraction of Metals by Reductive Dissolution of Oxidized Ores

    Directory of Open Access Journals (Sweden)

    Kevin B. Hallberg

    2013-01-01

    Full Text Available Biomining, the biotechnology that uses microorganisms to extract metals from ores and concentrates, is currently used exclusively for processing reduced ores and mine wastes. Metals of economic value also occur extensively in oxidized ores, such as nickel laterites. While these are not amenable to oxidative dissolution, the ferric iron minerals they contain can, in theory, be disrupted by iron reduction, causing associated metals to be released. We have harnessed the ability of the facultatively anaerobic, acidophilic bacterium Acidithiobacillus ferroooxidans to couple the oxidation of elemental sulphur to the reduction of ferric iron in the goethite fraction of a limonitic nickel ore at 30 °C. Nickel and other metals (Co, Cr and Mn were effectively solubilised and maintained in solution due to the low pH (1.8 of the leach liquor. The results highlight the potential for the bioprocessing of oxidized, iron-rich ores using an approach that is energy-saving and environmentally-benign compared with metallurgical processes currently applied to the extraction of Ni from lateritic ores.

  10. Species of organic matter and their role in the formation of statiform uranium ores

    International Nuclear Information System (INIS)

    Goleva, P.K.; Uspenskij, V.A.

    1983-01-01

    Results of investigation of organic mather (OM) from stratiform uranium ore manifestation in sedimentary Upper Proterozoic rocks of large trough with caledonian folded base are given. Role of OM in concentration of uranium-ore formations of two ore-bearing horizons, presented by rocks of facies of large lakes (''lacustrine'') and continental deltas (''alluvial'') was clarified. Characteristics of OM of rocks of ''lacustrine'' and ''alliivial'' facies, OM types, chemical composition of OM of ''alluvial'' horizon rocks, om spectrograms and diffractograms are presented. It was established that OM of ''lacustrine'' and ''alluvial'' ore-bearing horizons are presented by different morphological and genetic types, which played different roles in t.he process of uranium ore-formation. Faneiy dispersed OM, related to the category of oxidized lower kerites is present in ''lacustrine'' horizon. Ore uranium-arsenide nuneral association substitutes OM of early generation. The latest OM generation is related to epigenetic thread veinlet of dolomite and barite. In ''alluvial'' horizon OM is present in the form of carbonized vegetative residues+ ciosely assocaating with sulfides of different metals, and is presented by high-moiecular carbocyctnc hydroxy compouds. Uranium of carbonized vegetative residues is in finely dispersed state; the form of its fixation was not established. It is proposed that the major part of uranium was sorbed by OM during sedimentogenesis

  11. Thirty years of uranium ore processing in Spain

    International Nuclear Information System (INIS)

    Josa, J.M.

    1982-01-01

    Spanish background in the uranium ore processing includes ores from pegmatitic type deposits, vein deposits, sandstone, enrichments in metamorphic rocks, radioactive coals and non-conventional sources of uranium, such as wet phosphoric acid or copper liquors. Some tests have also done in order to recover uranium from very low grade paleozoic quartzites. We have also been involved in by-products recovery (copper) from uranium ores. The technologies that have been used are: physical concentration, combustion and roasting, conventional alkaline or acid methods, pressure, heap and bacteria leaching. Special attention was paid to recover uranium from the pregnant liquors and to develop suited equipment for it; solvent extraction and continuous ion exchange equipment was carefully studied. We have been involved in commercial size (500-3000 t/d) mills, but we have also developed transportable and reussable modular plants specially designed and suited to recover uranium from small and isolated deposits. In both cases the reduction of the environmental impact was taken in account. Spanish experience also includes nuclear purification aspects in order to get uranium nuclear compounds (ADU, UO 2 , UF 4 and UF 6 ). Wet (nitric-TBP) and dry (Fluid-bed) methods have been used. The best of these 30 years of experience in studies and in industrial practice, together with our new developments towards the future, could become in a good contribution for the medium size countries which are going to develop its own uranium industry. The way for these countries could be easier if they know what is valuable and what must be avoid in the uranium ore processing development. In this aim the whole paper was thought and written. (author)

  12. Mineralogical-Geochemical Peculiarities of Ores in Pyritaceous Fields of Filizchai Type in the Greater Caucasus

    Directory of Open Access Journals (Sweden)

    NOVRUZ A. NOVRUZOV

    2010-12-01

    Full Text Available Pyritaceous fields of the south slope of the Greater Caucasus confined to the Lower-Middle Jurassic sandy clayey deposits are: polygenic polychrone formations which were formed by a complex of hydrothermal sedimentary, hydrothermal metasomatic and hydrothermal metamorphogenic processes of ore formation. Filizchai pyritaceous polymetallic field is the largest in the region and can be characterized by diversity of texture-mineralogical types of ores, rich mineral composition and with geochemical spectrum. Some of the admixture components (Cd, In, Tl, Ga, Ge, Se, Hg are only in isomorphic forms in ores, others (Te, Bi, Au, Ag, Co, Sn, As along with it characterize in their own minerals. The Co is mainly concentrated in pyrite, pyrrhotine; Ag, Bi and also Te – in galenite and chalcopyrite; Se – in pyrite, pyrrhotine and galenite; in sphalerite (mainly in marmatite and chalcopyrite; Cd, Ga, Ge – in sphalerite, mainly in cleiophane; Au – in pyrite and chalcopyrite; Tl – in galenite and colloform pyrite. In all sulphides selenium prevails over tellurium (excepting the late chalcopyrite and cobalt over nickel. Maximum amount of cobalt is confined to pyrite from pyritaceous polymetallic ores and late generation of pyrrhotine. The nature of the connection between chemical elements in ores coordinates with determined stages of minerals formation. The main productive stage of ore formation bringing the main mass of gold, silver, rare and other precious components of ores are sulphosalt polymetallic stage of sulphur ploymetallic stage. Comparative analysis of absolute content of gold, silver and values of gold-silver relation in pyrite fields ores of region with appropriate values in meteorite standard indirectly indicates the relationship between gold-silver mineralization and assimilation crust source.

  13. Uranium extraction from gold-uranium ores

    Energy Technology Data Exchange (ETDEWEB)

    Laskorin, B.N.; Golynko, Z.Sh.

    1981-01-01

    The process of uranium extraction from gold-uranium ores in the South Africa is considered. Flowsheets of reprocessing gold-uranium conglomerates, pile processing and uranium extraction from the ores are presented. Continuous counter flow ion-exchange process of uranium extraction using strong-active or weak-active resins is noted to be the most perspective and economical one. The ion-exchange uranium separation with the succeeding extraction is also the perspective one.

  14. Natural resources sustainability: iron ore mining

    International Nuclear Information System (INIS)

    De La Torre de Palacios, Luis

    2011-01-01

    In the present article, a new tool to determine environmental sustainability, the energy impact index (EII) was developed to classify different iron mine projects according to two main parameters including energy consumption and CO 2 emissions. The EII considers the characteristics of the mineral (such as the quality, size, hardness, iron ore grade, reducibility, mineral/waste rate, and type of deposit), mining processes (type of exploitation, ore processing, available technology), and transportation (distance to cover).

  15. Determination of gold in gold ores

    International Nuclear Information System (INIS)

    Keedy, C.R.; Parson, L.; Shen, J.

    1989-01-01

    The gold content of placer gold flakes and gold bearing ores was determined by instrumental and radiochemical neutron activation analysis, respectively. It was discovered that significant errors result in the instrumental method for gold flakes as small as 10 mg due to sample self-absorption of neutrons during irradiation. Reliable results were obtained for both ore samples and gold flakes by dissolving the samples in aqua regia prior to irradiation. (author) 7 refs.; 3 tabs

  16. Uranium ore processing minimizing reagent losses

    International Nuclear Information System (INIS)

    Shaogiang, Chen; Moret, J.; Lyaudet, G.

    1989-01-01

    The uranium ore is treated by sodium carbonates and the solution is divided in two parts: a production solution which is decarbonated by an acid before uranium precipitation with sodium hydroxide and a recycling solution directly treated by sodium hydroxide for precipitation of about 85% of uranium and total transformation of sodium bicarbonate into sodium carbonate, the quantity of sodium hydroxide used on the recycling solution brings sodium ions required for attack of the ore [fr

  17. Decomposition of aluminosilicate ores of Afghanistan by hydrochloric acid

    International Nuclear Information System (INIS)

    Mamatov, E.D.; Khomidi, A.K.

    2015-01-01

    Present article is devoted to decomposition of aluminosilicate ores of Afghanistan by hydrochloric acid. The physicochemical properties of initial aluminosilicate ores were studied by means of X-ray phase, differential-thermal analysis methods. The chemical and mineral composition of aluminosilicate ores was considered. The kinetics of acid decomposition of aluminosilicate ores composed of two stages was studied as well. The flowsheets of complex processing of aluminium comprising ores by means of chloric and acid methods were proposed.

  18. Analytical fingerprint for tantalum ores from African deposits

    Science.gov (United States)

    Melcher, F.; Graupner, T.; Sitnikova, M.; Oberthür, T.; Henjes-Kunst, F.; Gäbler, E.; Rantitsch, G.

    2009-04-01

    Illegal mining of gold, diamonds, copper, cobalt and, in the last decade, "coltan" has fuelled ongoing armed conflicts and civil war in a number of African countries. Following the United Nations initiative to fingerprint the origin of conflict materials and to develop a traceability system, our working group is investigating "coltan" (i.e. columbite-tantalite) mineralization especially in Africa, also within the wider framework of establishing certified trading chains (CTC). Special attention is directed towards samples from the main Ta-Nb-Sn provinces in Africa: DR Congo, Rwanda, Mozambique, Ethiopia, Egypt and Namibia. The following factors are taken into consideration in a methodological approach capable of distinguishing the origin of tantalum ores and concentrates with the utmost probability: (1) Quality and composition of coltan concentrates vary considerably. (2) Mineralogical and chemical compositions of Ta-Nb ores are extremely complex due to the wide range of the columbite-tantalite solid solution series and its ability to incorporate many additional elements. (3) Coltan concentrates may contain a number of other tantalum-bearing minerals besides columbite-tantalite. In our approach, coltan concentrates are analyzed in a step-by-step mode. State-of-the-art analytical tools employed are automated scanning electron microscopy (Mineral Liberation Analysis; MLA), electron microprobe analysis (major and trace elements), laser ablation-ICP-MS (trace elements, isotopes), and TIMS (U-Pb dating). Mineral assemblages in the ore concentrates, major and trace element concentration patterns, and zoning characteristics in the different pegmatites from Africa distinctly differ from each other. Chondrite-normalized REE distribution patterns vary significantly between columbite, tantalite, and microlite, and also relative to major element compositions of columbites. Some locations are characterized by low REE concentrations, others are highly enriched. Samples with

  19. Chapter 3. Classical method of uranium leaching from ores and reasons for incomplete recovery at dumps of State Enterprise 'VOSTOKREDMET'. 3.3. Basic regularities of uranium ores leaching

    International Nuclear Information System (INIS)

    Khakimov, N.; Nazarov, Kh.M.; Mirsaidov, I.U.

    2012-01-01

    Present article is devoted to basic regularities of uranium ores leaching. It was found that the basic method of uranium ores enrichment and producing of reasonably rich and pure uranium concentrates (usually technical uranium oxide) is a chemical concentration concluded in selective uranium leaching from ore raw materials with further, uranium compounds - so called uranium chemical concentrates. Such reprocessing of uranium ores with the purpose of uranium chemical concentrates production, currently, are produced everywhere by hydrometallurgical methods. This method in comparison with enrichment and thermal reprocessing is a universal one. Hydrometallurgy - the part of chemical technology covering so called moist methods of metals and their compounds (in the current case, uranium) extraction from raw materials, where they are contained. It can be ores or ore concentrates produced by radiometric, gravitational, floatation enrichment, sometimes passed through high-temperature reprocessing or even industry wastes. The basic operation in hydrometallurgy is its important industrial element - metal or metals leaching as one or another compound. Leaching is conversion of one or several components to solution under impact of relevant technical solvents: water, water solutions, acids, alkali or base, solution of some salts and etc. The basic purpose of leaching in uranium technology is to obtain the most full and selective solution of uranium.

  20. Iron-ore resources of the United States including Alaska and Puerto Rico, 1955

    Science.gov (United States)

    Carr, Martha S.; Dutton, Carl E.

    1959-01-01

    ; and potential ore, material likely to become usable under more favorable conditions. The tonnage and grade of material of combined reserves and potential ore in each of the deposits known or believed to contain at least 200,000 long tons of iron-ore resources are tabulated in this report, and numerous sources of additional information are given in a selected bibliography. The total domestic iron-ore resources are estimated at approximately 75,000 million long tons of crude ore. About 10,000 million tons of the resources is reserves of crude ore that will probably yield 5,500 million tons of concentrates and direct-shipping ore. About 65,000 million tons is potential ore and may yield 25,000 million tons of concentrates and some direct-shipping ore.

  1. Ores and Climate Change - Primary Shareholders

    Science.gov (United States)

    Stein, Holly J.; Hannah, Judith L.

    2015-04-01

    Many in the economic geology community concern themselves with details of ore formation at the deposit scale, whether tallying fluid inclusion data to get at changes in ore-forming fluids or defining structures that aid and abet mineralization. These compilations are generally aimed at interpretation of events at the site of ore formation, with the goal being assignment of the deposit to a sanctioned ore deposit model. While providing useful data, this approach is incomplete and does not, by itself, serve present-day requirements for true interdisciplinary science. The ore-forming environment is one of chaos and disequilibrium at nearly all scales (Stein, 2014). Chaos and complexity are documented by variably altered rocks, veins or disseminated mineralization with multi-generational fluid histories, erratic and unusual textures in host rocks, and the bitumen or other hydrocarbon products entwined within many ore deposits. This should give pause to our drive for more data as a means to find "the answer". The answer lies in the kind of data collected and more importantly, in the way we interpret those data. Rather than constructing an ever-increasing catalog of descriptive mutations on sanctioned ore deposit models (e.g., IOGC or Iron-Oxide Copper Gold deposits), the way forward is to link source and transport of metals, sulfur, and organic material with regional and ultimately whole Earth chemical evolution. Important experimental work provides chemical constraints in controlled and behaved environments. To these data, we add imagination and interpretation, always tying back to field observations. In this paper, several key points are made by way of ore deposit examples: (1) many IOCG deposits are outcomes of profound changes in the chemistry of the Earth's surface, in the interplay of the atmosphere, hydrosphere, biosphere, and lithosphere; (2) the redox history of Fe in deep earth may be ultimately expressed in the ore-forming sequence; and (3) the formation of

  2. Spectrometric gamma investigations concerning zinc-lead ores and the products of their processing

    International Nuclear Information System (INIS)

    Girczys, J.; Skowronek, J.; Zrodlowski, B.

    1983-01-01

    Zinc-lead ore and products of its enrichment were investigated using gamma spectrometry for the content of uranium, thorium and potassium 40. It was stated that the mean content of these elements in a deposit does not diverge from their mean concentration in the lithosphere. They also accompany the surrounding rocks. As a result of mechanical processing of this ore radionuclides pass discards in which they do not form concentrations dangerous for life, either. In the exploitation areas and in the surroundings there is no state of ecological hazard. (author)

  3. Surface modification and column flotation of a massive ilmenite ore

    International Nuclear Information System (INIS)

    Fan, X.; Rowson, N.A.

    2002-01-01

    The main problems with ilmenite flotation in impeller-type flotation machines are the poor flotation behaviour of ilmenite and the negative effect of slimes. These cause high ilmenite losses in tailings even when a large dosage of fatty acid and fuel oil is consumed. In this study, microwave radiation pre-treatment and ilmenite surface activation were used to modify the surface properties of a massive ilmenite ore sample from Norway to improve ilmenite flotability. A column cell was used to minimize the negative effect of slimes on ilmenite separation efficiency. When ilmenite flotation was performed in a 1 litre Denver cell, the flotation recovery of titanium dioxide from the ilmenite ore sample was only 68.5% (31.1% TiO 2 ) under conventional flotation conditions. After microwave radiation pre-treatment for three minutes at 2600 W and 2.45 GHz, the ferrous ions on ilmenite particle surfaces were converted into ferric ions; hence, the recovery increased from 68.5% to 86.8%. The concentrate grade increased from 31.1% TiO 2 to 32.1% TiO 2 . In ilmenite activation flotation, Pb 2+ ions can be selectively adsorbed on to ilmenite particle surfaces as active sites and therefore enhance the adsorption of oleate ions on ilmenite surfaces. With the addition of 60 g/ton Pb(NO 3 ) 2 , ilmenite flotation recovery increased from 68.5% to 85.1%. However, the quality of ilmenite concentrates was not improved due to the negative effect of slimes. After a two stage cleaning, the grade of ilmenite concentrates was only about 31% TiO 2 . The combination of microwave radiation pre-treatment and the application of a column cell overcame both problems of poor flotability and the negative effect of slimes. When the Denver cell was replaced by a column cell and the massive ilmenite ore sample was pre-treated using microwave radiation for three minutes, the ilmenite concentrate grade increased from 31.1% TiO 2 to 42.9% TiO 2 and the titanium dioxide recovery increased from 68.5% to 90

  4. Effects of barium chloride treatment of uranium mill tailings and ore on radon emanation and 226Ra levels. Progress report

    International Nuclear Information System (INIS)

    Ibrahim, S.A.; Flot, S.L.

    1983-01-01

    The purpose of this study was to investigate the effect of barium chloride treatments on: reduction of 222 Rn emanation from mill wastes; reduction of 226 Ra levels in wastewater; and decreased leachability of 226 Ra from mill wastes. Baseline 226 Ra concentrations were determined for ore and tailings as well as radon emanation fractions. Uranium ore was treated with soluble barium at concentrations of 10, 25, 50, and 100 mg per litre of slurry. The leach-liquor declined in 226 Ra concentration by as much as 50%. When soluble potassium as well as barium was used in the treatment process at equal concentrations of 10, 25, 50, and 100 mg per litre of slurry, a similar reduction was observed. No significant difference was noted between the two treatment regimes. An accelerated leaching experiment was performed on the ore treated with barium chloride. All treatment groups except that treated with 10 mg of soluble barium per litre of slurry showed significant decreases in leachability. Available 222 Rn (corresponds with radon emanation fraction) was measured in treated and untreated ore. Ore treated with concentrations of Ba ++ up to 1.00 mg per gram of ore did not show a statistically significant reduction in available 222 Rn, however when potassium sulfate was also added, a significant decline was noted. This study suggests that barium chloride treatments reduce radon emanation from mill wastes and reduce 226 Ra levels in wastewater. Leachability of 226 Ra from treated samples decreased markedly. 19 references, 8 figures, 7 tables

  5. Thallium-rich pyrite ores from the Apuan Alps, Tuscany, Italy:constraints for their origin and environmental concerns

    Science.gov (United States)

    D'Orazio, Massimo; Biagioni, Cristian; Dini, Andrea; Vezzoni, Simone

    2017-06-01

    The southern sector of the Apuan Alps (AA) massif, Tuscany, Italy, is characterized by the occurrence of a series of baryte-pyrite-iron oxide orebodies whose Tl-rich nature was recognized only recently. The geochemistry of the pyrite ore was investigated through inductively coupled plasma mass spectrometry. In addition, lead isotope data for selected pyrite ores from AA were collected. Pyrite ores are characterized by a complex geochemistry, with high concentrations of Tl (up to 1100 μg/g) coupled with high As and Sb contents; the Co/Ni ratio is always <1. Geochemical data of pyrite and marcasite ore samples from other mining districts of Tuscany have been collected in order to compare them with those from the AA. These samples usually have very low Tl content (less than 2 μg/g) and high to very high Co/Ni and As/Sb ratios. Only some samples from the Sb-Hg ore deposits showed very high Tl concentrations (up to 3900 μg/g). Another difference is related to the lead isotope composition, with pyrite ores from AA markedly less radiogenic than those from the other deposits from Tuscany. Geochemical data of pyrite ores from AA give new insights on the genesis of the baryte-pyrite-iron oxide orebodies, relating their formation to low-temperature hydrothermal systems active during early Paleozoic; in addition, these data play a fundamental role in assessing the environmental impact of these deposits.

  6. Bioleaching of low-grade uranium ore using Acidithiobacillus ferrooxidans

    International Nuclear Information System (INIS)

    Pal, S.; Das, T.; Sukla, L.B.; Roy Chaudhury, G.; Pradhan, D.

    2010-01-01

    Bioleaching of uranium was carried out with Turamdih ore sample procured from Uranium Corporation of India Limited, Jaduguda. The bacterial strain that was used in the leaching experiments was isolated from the Jaduguda mine water sample. Efficiency of bioleaching was studied by varying parameters like pulp density and initial ferrous concentration as source of energy. It is observed that the efficiency of bioleaching was 49% at 10% pulp density (w/v) and initial pH 2.0. Addition of external has no effect on efficiency of bioleaching showing domination of direct leaching mechanism over indirect. (author)

  7. CHAIN EXTENDER AND EMULSIFIER APPLICATION IN IRON ORE FLOTATION

    Directory of Open Access Journals (Sweden)

    José Pedro da Silva

    2013-06-01

    Full Text Available The present study aims to evaluate the reverse flotation performance of iron ore, using collector (amine, in the presence and absence of chain extender (diesel oil and emulsifier (sodium lauryl sulfate.Six tests were realized with duplicate. Tests using amine, diesel oil and sodium lauryl sulphate show the better results, with metallurgical recovery of 91.82% and the concentrate silica equal 1.68%. Thus, it is found that the use of emulsifier and chain extender together with the amine, shows better results in the flotation, in terms of metal recovery and selectivity, when compared to using only amine or amine and diesel oil.

  8. Study on epigenetic alterations of ore-enclosing sedimentary rocks

    International Nuclear Information System (INIS)

    Kondrat'eva, I.A.; Komarova, G.V.

    1985-01-01

    Epigenetic alterations of sedimentary rocks under effect of exogenous undeground waters of various types: near-surface, ground, stratum, and deep circulation waters, are considered. Association to postsedimentary tectonic structures, confinement of neogenesis to areas of high permeability (porous or crack one), geochemical contradictions between mineral neogenis and facial outlook of deposits, noncoincidence of variability gradient of authigenous mineral associations with variability of primary facial signs of deposits, regular position of mineral formations and ore concentrations in epigenetic mineralogo-geochemical zonation are referred to epigenetic criteria. The complex of epigenetic alterations accompanying mineralization is frequently used as a search sign of uranium deposit of a certain type

  9. Direct Biohydrometallurgical Extraction of Iron from Ore. Final Technical Report

    International Nuclear Information System (INIS)

    T.C. Eisele

    2005-01-01

    A completely novel approach to iron extraction was investigated, based on reductive leaching of iron by anaerobic bacteria. Microorganisms were collected from an anaerobic bog where natural seepage of dissolved iron was observed. This mixed culture was used to reduce insoluble iron in a magnetite ore to the soluble ferrous (Fe +2 ) state. While dissolution rates were slow, concentrations of dissolved iron as high as 3487 mg/l could be reached if sufficient time was allowed. A factorial study of the effects of trace nutrients and different forms of organic matter indicated that the best dissolution rates and highest dissolved iron concentrations were achieved using soluble carbohydrate (sucrose) as the bacterial food source, and that nutrients other than nitrogen, phosphorus, potassium, sodium, and acetate were not necessary. A key factor in reaching high levels of dissolved iron was maintaining a high level of carbon dioxide in solution, since the solubility of iron carbonates increases markedly as the quantity of dissolved carbon dioxide increases. Once the iron is dissolved, it has been demonstrated that the ferrous iron can then be electroplated from solution, provided that the concentration of iron is sufficiently high and the hydrogen ion concentration is sufficiently low. However, if the leaching solution is electrolyzed directly, organic matter precipitates at the cathode along with the metallic iron. To prevent this problem, the ferrous iron should be separated from the bulk solution in a more concentrated, purified form. One route to accomplishing this is to take advantage of the change in solubility of ferrous iron as a function of carbon dioxide concentration. By cycling the concentration of carbon dioxide in solution, it is possible to produce an iron-rich concentrate that should be suitable for electrolysis. This represents the first viable hydrometallurgical method for leaching iron directly from ore and producing metallic iron

  10. Direct Biohydrometallurgical Extraction of Iron from Ore. Final technical report

    International Nuclear Information System (INIS)

    T.C. Eisele

    2005-01-01

    A completely novel approach to iron extraction was investigated, based on reductive leaching of iron by anaerobic bacteria. Microorganisms were collected from an anaerobic bog where natural seepage of dissolved iron was observed. This mixed culture was used to reduce insoluble iron in a magnetite ore to the soluble ferrous (Fe +2 ) state. While dissolution rates were slow, concentrations of dissolved iron as high as 3487 mg/l could be reached if sufficient time was allowed. A factorial study of the effects of trace nutrients and different forms of organic matter indicated that the best dissolution rates and highest dissolved iron concentrations were achieved using soluble carbohydrate (sucrose) as the bacterial food source, and that nutrients other than nitrogen, phosphorus, potassium, sodium, and acetate were not necessary. A key factor in reaching high levels of dissolved iron was maintaining a high level of carbon dioxide in solution, since the solubility of iron carbonates increases markedly as the quantity of dissolved carbon dioxide increases. Once the iron is dissolved, it has been demonstrated that the ferrous iron can then be electroplated from solution, provided that the concentration of iron is sufficiently high and the hydrogen ion concentration is sufficiently low. However, if the leaching solution is electrolyzed directly, organic matter precipitates at the cathode along with the metallic iron. To prevent this problem, the ferrous iron should be separated from the bulk solution in a more concentrated, purified form. One route to accomplishing this is to take advantage of the change in solubility of ferrous iron as a function of carbon dioxide concentration. By cycling the concentration of carbon dioxide in solution, it is possible to produce an iron-rich concentrate that should be suitable for electrolysis. This represents the first viable hydrometallurgical method for leaching iron directly from ore and producing metallic iron

  11. Bottle roll leach test for Temrezli uranium ore

    International Nuclear Information System (INIS)

    Çetin, K.; Bayrak, M.; Turan, A. İsbir; Üçgül, E.

    2014-01-01

    The bottle roll leach test is one of the dynamic leaching procedure which can meet in-situ mining needs for determining suitable working conditions and helps to simulate one of the important parameter; injection well design. In this test, the most important parameters are pulp density, acidic or basic concentration of leach solution, time and temperature. In recent years, bottle roll test is used not only for uranium but also gold, silver, copper and nickel metals where in situ leach (ISL) mining is going to be applied. For this purpose for gold and silver metal cyanide bottle roll tests and for uranium metal; acidic and basic bottle roll tests could be applied. The new leach test procedure which is held in General Directorate of Mineral Research and Exploration (MTA) of Turkey is mostly suitable for determining metal extraction conditions and recovery values in uranium containing ore bodies. The tests were conducted with samples taken from Temrezli Uranium Ore located in approximately 200 km east of Turkey’s capital, Ankara. Mining rights of Temrezli Ore is controlled 100% by Anatolia Energy Ltd. The resource estimate includes an indicated mineral resource of 10.827 Mlbs U_3O_8 [~4160 t U] at an average grade of 1426 ppm [~1210 ppm U] and an additional inferred resource of 6.587 Mlbs of U_3O_8 [~2530 t U] at an average grade of 904 ppm [~767 ppm U]. In accordance with the demand from Anatolia Energy bottle roll leach tests have been initiated in MTA laboratories to investigate the recovery values of low-grade uranium ore under in-situ leach conditions. Bottle roll leaching tests are performed on pulverized samples with representative lixiviant solution at ambient pressure and provide an initial evaluation of ore leachability with a rough estimate of recovery value. At the end of the tests by using 2 g/L NaHCO_3 and 0.2 g/L H_2O_2 more than 90% of uranium can pass into leach solution in 12 days. (author)

  12. Research of geological technologic condition in laboratory about the ore of 501 deposits

    International Nuclear Information System (INIS)

    Ma Guoxiang; Yu Baoli; Gao Yuyou; Li Changhua

    2009-01-01

    501 deposits of uranium ore grade is 0.052%. The radio of U +6 /U 4+ is 1.7-4.6. there is less content of sarbonate, such as sulfide and organic matter which disservice baptist uranium geological process, and the uranium and oxygen with a high level in the water of seam. The content of [HCO 3 ] - is lower. By conducting the static leaching test, the important technical parameters of uranium ore extraction are determined: with 7.91 g/L H 2 SO 4 , to soak uranium ore which the grade is between 0.007% and 0.216% for 48 hours, the uranium extraction rate of 64.69-99.17%, and extract uranium concentration 9.51-427.6 mg/L; the formula of infusion solution is obtained by using percolation leaching test: 6-8 g/L H 2 SO 4 , the rate of uranium extraction is 95.71%-96.33%, an average of leaching solution uranium concentration of 88.33-111.32 mg/L, leaching liquid-solid ratio of 4.46-5.66, ore tons of sulfuric acid consumption to 27.58-29.83 kg/t, extraction of uranium 1 kg of sulfuric acid consumption to 55.17-60.06 kg. That indicate the geological technologic conditions which the leaching of uranium ore deposits is better. (authors)

  13. Ore potential of basic rocks in Finland

    International Nuclear Information System (INIS)

    Reino, J.; Ekberg, M.; Heinonen, P.; Karppanen, T.; Hakapaeae, A.; Sandberg, E.

    1993-02-01

    The report is associated with a study programme on basic rocks, which has the aim to complement the preliminary site investigations on repository for TVO's (Teollisuuden Voima Oy) spent nuclear fuel. The report comprises a mining enterprise's view of the ore potential of basic plutonic rocks in Finland. The ores associated with basic plutonic rocks are globally known and constitute a significant share of the global mining industry. The ores comprise chromium, vanadium-titanium-iron, nickel-copper and platinum group element ores. The resources of the metals in question and their mining industry are examined globally. A review of the use of these metals in the industry is presented as well. General factors affecting the mining industry, such as metal prices, political conjunctures, transport facilities, environmental requirements and raw material sources for the Finnish smelters have been observed from the point of view of their future effect on exploration activity and industrial development in Finland. Information on ores and mineralizations associated with Finnish basic rocks have been compiled in the report. The file comprises 4 chromium occurrences, 8 vanadium-titanium-iron occurrences, 13 PGE occurrences and 38 nickel-copper occurrences

  14. Mortality among sulfide ore miners

    International Nuclear Information System (INIS)

    Ahlman, K.; Koskela, R.S.; Kuikka, P.; Koponen, M.; Annanmaeki, M.

    1991-01-01

    Lung cancer mortality was studied during 1965-1985 in Outokumpu township in North Karelia, where an old copper mine was located. Age-specific lung cancer death rates (1968-1985) were higher among the male population of Outokumpu than among the North Karelian male population of the same age excluding the Outokumpu district (p less than .01). Of all 106 persons who died from lung cancer during 1965-1985 in Outokumpu township, 47 were miners of the old mine, 39 of whom had worked there for at least three years and been heavily exposed to radon daughters and silica dust. The study cohort consisted of 597 miners first employed between 1954 and 1973 by a new copper mine and a zinc mine, and employed there for at least 3 years. The period of follow-up was 1954-1986. The number of person-years was 14,782. The total number of deaths was 102; the expected number was 72.8 based on the general male population and 97.8 based on the mortality of the male population of North Karelia. The excess mortality among miners was due mainly to ischemic heart disease (IHD); 44 were observed, the expected number was 22.1, based on the general male population, and the North Karelian expected number was 31.2 (p less than .05). Of the 44 miners who died from IHD, 20 were drillers or chargers exposed to nitroglycerin in dynamite charges, but also to several simultaneous stress factors including PAHs, noise, vibration, heavy work, accident risk, and working alone. Altogether 16 tumors were observed in the cohort. Ten of these were lung cancers, the expected number being 4.3. Miners who had died from lung cancer were 35-64 years old, and had entered mining work between 1954 and 1960. Five of the ten lung cancer cases came from the zinc mine (1.7 expected). Three of them were conductors of diesel-powered ore trains

  15. Uranium extraction from Uro area phosphate ore, Nuba mountains, Sudan

    International Nuclear Information System (INIS)

    Mohammed, A. A.; Eltayeb, M. A. H.

    2003-01-01

    This study was carried out mainly to extract uranium from Uro area phosphate ore in the eastern part of Nuba mountains near Abu Gibiha town in southern Kurdufan state. For this purpose first, the phosphate ore samples were decomposed with sulphuric acid. the resulting phosphoric acid was filtered off, and pretreated with pyrite and activated charcoal. the chemical analysis of the obtained grain phosphoric acid showed that about 98% of uranium content of the phosphate ore was rendered soluble in the phosphoric acid. The clear green phosphoric acid was introduced to uranium extraction by 25% tributylphosphate (Tbp) in kerosene. The effect of several factors on the extraction and stripping processes namely, interference's effect, the suitable strip solution, the required number of extraction and stripping stages, the optimum phase ratio have been studied in details. A three stage extraction at a phase ratio (aqueous/organic) of 1:2, followed by two stages stripping using 0.5 M sodium carbonate solution at a phase ratio (A/O) of 1:4 were found to be the optimum conditions to report more than 98% of uranium content in green phosphoric acid to the aqueous phase as uranyl tricarbonate complex (UO 2 (CO 3 ) 3 ) 4- . By applying sodica decomposition upon the stripping carbonate solution using 50% sodium hydroxide, about 98% of uranium content was precipitated as sodium diuranate concentrate (Na 2 U 2 O 7 ). The chemical analysis using atomic absorption spectrometry (Aas) showed a good agreement between the specification of the obtained uranium concentrate with the standard commercial specification of sodium diuranate concentrate. Further purification was achieved for the yellow cake by selective precipitation of uranium from the solution as uranium peroxide (UO 4 .2H 2 O) using 30% hydrogen peroxide. Finally the uranium peroxide precipitated was calcined at 450 degree C to obtain the orange powder uranium trioxide (UO 3 ). The chemical analysis of the final uranium trioxide

  16. REM-containing silicate concentrates

    International Nuclear Information System (INIS)

    Pavlov, V F; Shabanova, O V; Pavlov, I V; Pavlov, M V; Shabanov, A V

    2016-01-01

    A new method of advanced complex processing of ores containing rare-earth elements (REE) is proposed to obtain porous X-ray amorphous aluminosilicate material with a stable chemical composition which concentrates oxides of rare-earth metals (REM). The ferromanganese oxide ores of Chuktukon deposit (Krasnoyarsk Region, RF) were used for the experiment. The obtained aluminosilicate material is appropriate for treatment with 5 - 15% solutions of mineral acids to leach REM. (paper)

  17. REM-containing silicate concentrates

    Science.gov (United States)

    Pavlov, V. F.; Shabanova, O. V.; Pavlov, I. V.; Pavlov, M. V.; Shabanov, A. V.

    2016-01-01

    A new method of advanced complex processing of ores containing rare-earth elements (REE) is proposed to obtain porous X-ray amorphous aluminosilicate material with a stable chemical composition which concentrates oxides of rare-earth metals (REM). The ferromanganese oxide ores of Chuktukon deposit (Krasnoyarsk Region, RF) were used for the experiment. The obtained aluminosilicate material is appropriate for treatment with 5 - 15% solutions of mineral acids to leach REM.

  18. Economic evaluation of preconcentration of uranium ores

    International Nuclear Information System (INIS)

    1981-04-01

    The economics of two options for the preconcentration of low-grade uranium ores prior to hydrochloric acid leaching were studied. The first option uses flotation followed by wet high-intensity magnetic separation. The second option omits the flotation step. In each case it was assumed that most of the pyrite in the ore would be recovered by froth flotation, dewatered, and roasted to produce sulphuric acid and a calcine suitable for acid leaching. Savings in operating costs from preconcentration are offset by the value of uranium losses. However, a capital saving of approximately 6 million dollars is indicated for each preconcentration option. As a result of the capital saving, preconcentration appears to be economically attractive when combined with hydrochloric acid leaching. There appears to be no economic advantage to preconcentration in combination with sulphuric acid leaching of the ore

  19. Radiometric sorting of Rio Algom uranium ore

    International Nuclear Information System (INIS)

    Cristovici, M.A.

    1983-11-01

    An ore sample of about 0.2 percent uranium from Quirke Mine was subjected to radiometric sorting by Ore Sorters Limited. Approximately 60 percent of the sample weight fell within the sortable size range: -150 + 25 mm. Rejects of low uranium content ( 2 (2 counts/in 2 ) but only 7.6 percent of the ore, by weight, was discarded. At 0.8-0.9 counts/cm 2 (5-6 counts/in 2 ) a significant amount of rejects was removed (> 25 percent) but the uranium loss was unacceptably high (7.7 percent). Continuation of the testwork to improve the results is proposed by trying to extend the sortable size range and to reduce the amount of fines during crushing

  20. Mining of sedimentary-type ore deposits

    International Nuclear Information System (INIS)

    Bruha, J.; Slovacek, T.; Berka, J.; Sadilek, P.

    1992-01-01

    A procedure is proposed for mining sedimentary-type ore deposits, particularly uranium deposits, using the stope-pillar technique. The stope having been mined out, the free room is filled with hydro-setting gob from the surface. A precondition for the application of this technique is horizontal ore mineralization in sediments where the total thickness of the mineralized ore layer is at least 3 to 5 m. Mining losses do not exceed 5%. For thicknesses greater than 5 m, the roof is reinforced and the walls are secured with netting. The assets of the technique include higher labor productivity of the driving, lower material demands in reinforcing and filling, lower power consumption, and reduced use of explosives. (Z.S.). 3 figs

  1. Manganese Ores from South Sulawesi: Their Potential Uses as Raw Materials for Metallurgical Industry

    Directory of Open Access Journals (Sweden)

    Sufriadin Sufriadin

    2017-03-01

    Full Text Available Characterization of manganese ores from Barru and Bone regencies of South Sulawesi has been conducted with the aim at clarification of their mineralogical and chemical composition for their potential uses as the raw materials for metallurgical industry. Mineralogical properties of the ores analyzed by means of optical microscopy and X-ray diffractometry (XRD show that samples from Barru consist mainly of rhodochrosite (MnCO3 with less cryptomelane, groutite, bixbyite, and todorokite. Goethite, calcite and small amount of quartz present as impurities. Manganese ore samples from Bone are predominantly composed of pyrolusite (MnO2 with subordinate ramsdellite and hollandite. Barite, quartz, hematite and clay are present as gangue minerals. Chemical compositions determined by using XRF method revealed that Barru samples contain higher in MnO (average is 40.07 wt% than the Bone samples (average is 34.36 wt%. Similarly, Fe2O3 and CaO are also higher in Barru than those of the Bone samples. In contrast, concentrations of SiO2 and total alkali (K2O + Na2O are lower in the Barru samples. The average P2O5 content of samples in both areas is low (<0.2 wt%. Relatively higher grade of Fe2O3 in the Barru ore implies that it has potential application for ferromanganese production; whereas the elevated SiO2 content of the Bone ore is a good indication for silicomanganese manufacture. However, both ores may not favorable to be directly used as raw materials in metallurgical uses. Prior to be used, the ores should be treated by applying physical beneficiation in order to reduce deleterious elements.

  2. The determination of trace quantities of thorium and uranium in thick ore samples by proton-induced x-ray emission

    International Nuclear Information System (INIS)

    Cohen, D.D.; Duerden, P.; Clayton, E.

    1979-07-01

    Proton-induced X-ray emission (PIXE) techniques have been used to estimate the concentrations of trace quantities of thorium and uranium in powdered rock and ore samples. Standards of known concentrations were prepared in a carbon matrix and the yields from these used to determine simultaneously the concentrations of thorium and uranium in the ore samples. The experimental detection limit of the technique was found to be 3 to 4 μg g -1 for a 100 μC irradiation. The appropriate matrix corrections for a carbon and ore matrix have been calculated for thick targets and taken into consideration

  3. Geochemical features of the ore-bearing medium in uranium deposits in the Khiagda ore field

    Science.gov (United States)

    Kochkin, B. T.; Solodov, I. N.; Ganina, N. I.; Rekun, M. L.; Tarasov, N. N.; Shugina, G. A.; Shulik, L. S.

    2017-09-01

    The Neogene uranium deposits of the Khiagda ore field (KOF) belong to the paleovalley variety of the hydrogene type and differ from other deposits of this genetic type in the geological and geochemical localization conditions. The contemporary hydrogeochemical setting and microbiological composition of ore-bearing medium are discussed. The redox potential of the medium (Eh is as low as-400 mV) is much lower than those established at other hydrogenic deposits, both ancient Late Mesozoic and young Late Alpine, studied with the same methods in Russia, Uzbekistan, and southern Kazakhstan. The pH of subsurface water (6.86-8.13) differs in significant fluctuations both between neighboring deposits and within individual ore lodes. Hydrogen-forming and denitrifying bacteria are predominant in microbiological populations, whereas sulfate-reducing bacteria are low-active. The consideration of these factors allowed us to describe the mechanism of uranium ore conservation as resulting from the development of the cryolithic zone, which isolates ore lodes from the effect of the external medium. Carbonated water supplied from the basement along fault zones also participates in the formation of the present-day hydrogeochemical setting. Based on the features of the ore-bearing medium, we propose a method of borehole in situ acid leaching to increase the efficiency of mining in the Khiagda ore field.

  4. Study on the determination of ore-formation age of primary gold ore

    International Nuclear Information System (INIS)

    Ying Junlong; Zhao Puyun; Guo Hong

    1997-01-01

    The accurate determination of gold ore-formation age and ore-source isotope composition are of important significance in the research on gold geology and prospecting. According to the summary of three year indoor and field work, the ore-formation ages and isotope compositions of some typical gold deposits were obtained: The age of gold ore of the Wuhuaaobao deposit in geo-syncline region north to the north margin of North-China paleo-land is 130-120 Ma corresponding to the Late-orogenic stage. The ore-formation age of the Saiwusu gold deposit in the southern platform region is 211 +- 15 Ma, recycling reworking of the old-land. The Hougou-Huangtuliang gold deposit located in the middle of the platform region is 243 +- 7 Ma old attributed to the regeneration ore-formation on the old-land. the age of Jiaojia-Rushan gold deposit in Eastern Shandong is 122.7 +- 3.4 Ma and 128 +- 23 Ma belonging to Yanshanian stage. The Babaoshan gold-silver deposit in Cathaysian old-land is 140 +- 5 Ma old originated from volcanic hydrothermal ore-formation

  5. Genesis of iron-apatite ores in Posht-e-Badam Block (Central Iran) using REE geochemistry

    Science.gov (United States)

    Mokhtari, Mir Ali Asghar; Zadeh, Ghader Hossein; Emami, Mohamad Hashem

    2013-06-01

    Rare earth elements in apatites of different ore types show characteristic patterns which are related to different modes of formation of the ores. Most of the apatite-bearing iron ores are associated with alkaline magmas with LREE/HREE fractionation varying from moderate to steep. Iron-apatite deposits in Posht-e-Badam Block (Central Iran) have a high concentration of REE (more than 1000 ppm up to 2.5%), and show a strong LREE/HREE ratio with a pronounced negative Eu anomaly. This REE pattern is typical of magmatic apatite and quiet distinct from sedimentary apatites (phosphorites) which have a low REE contents and Ce negative anomalies. On the other hand, they are comparable to the REE patterns of apatites in Kiruna-type iron ores in different parts of the world. The REE patterns of apatites, iron-apatite ores and iron ores are similar and only have different REE contents. This similarity indicates a genetic relation for these rocks. Most of the iron-apatite deposits in Central Iran have similar REE patterns too, which in turn show a genetic relation for all of these deposits. This similarity indicates a similar origin and processes in their genesis. There are some small intrusions around some of the iron-apatite deposits that are petrographically identified as syenite and gabbro. These intrusions also have REE patterns similar to that of iron-apatite ores. This demonstrates a genetic relation between these intrusions and iron-apatite ores. The REE patterns of apatites in different deposits of Posht-e-Badam Block iron-apatite ores show an affinity to alkaline to sub-alkaline magmas and rifting environment. The alkaline host rocks of Central Iran iron-apatite ores are clearly related to an extensional setting where rifting was important (SSE-NNW fault lines). A probable source for this large scale ore forming processes is relatively low partial melting of mantle rocks. The ores have originated by magmatic differentiation as a late phase in the volcanic cycle

  6. The physical hydrogeology of ore deposits

    Science.gov (United States)

    Ingebritsen, Steven E.; Appold, M.S.

    2012-01-01

    Hydrothermal ore deposits represent a convergence of fluid flow, thermal energy, and solute flux that is hydrogeologically unusual. From the hydrogeologic perspective, hydrothermal ore deposition represents a complex coupled-flow problem—sufficiently complex that physically rigorous description of the coupled thermal (T), hydraulic (H), mechanical (M), and chemical (C) processes (THMC modeling) continues to challenge our computational ability. Though research into these coupled behaviors has found only a limited subset to be quantitatively tractable, it has yielded valuable insights into the workings of hydrothermal systems in a wide range of geologic environments including sedimentary, metamorphic, and magmatic. Examples of these insights include the quantification of likely driving mechanisms, rates and paths of fluid flow, ore-mineral precipitation mechanisms, longevity of hydrothermal systems, mechanisms by which hydrothermal fluids acquire their temperature and composition, and the controlling influence of permeability and other rock properties on hydrothermal fluid behavior. In this communication we review some of the fundamental theory needed to characterize the physical hydrogeology of hydrothermal systems and discuss how this theory has been applied in studies of Mississippi Valley-type, tabular uranium, porphyry, epithermal, and mid-ocean ridge ore-forming systems. A key limitation in the computational state-of-the-art is the inability to describe fluid flow and transport fully in the many ore systems that show evidence of repeated shear or tensional failure with associated dynamic variations in permeability. However, we discuss global-scale compilations that suggest some numerical constraints on both mean and dynamically enhanced crustal permeability. Principles of physical hydrogeology can be powerful tools for investigating hydrothermal ore formation and are becoming increasingly accessible with ongoing advances in modeling software.

  7. Effective Processing of the Iron Ores

    Science.gov (United States)

    Kuskov, Vadim; Kuskova, Yana; Udovitsky, Vladimir

    2017-11-01

    Effective technology for a complex wasteless processing of the iron ores has been designed and includes three main components (plats): comminution plant, briquette plant, pigment plant. The comminution is done per energy effective technology. Using of briquetting for ores clotting enables the costs cut and brings to a higher level of environmental safety of the process. Briquette formation can be done as a regular pressing, as an extrusion. Developed technology allows to produce high quality competitively products for metallurgy industry and red iron oxide pigments. The whole production line impacts the environment in a minimal manner.

  8. Effective Processing of the Iron Ores

    Directory of Open Access Journals (Sweden)

    Kuskov Vadim

    2017-01-01

    Full Text Available Effective technology for a complex wasteless processing of the iron ores has been designed and includes three main components (plats: comminution plant, briquette plant, pigment plant. The comminution is done per energy effective technology. Using of briquetting for ores clotting enables the costs cut and brings to a higher level of environmental safety of the process. Briquette formation can be done as a regular pressing, as an extrusion. Developed technology allows to produce high quality competitively products for metallurgy industry and red iron oxide pigments. The whole production line impacts the environment in a minimal manner.

  9. Application of biohydrometallurgy to uranium ore processing

    International Nuclear Information System (INIS)

    Zhang Jiantang

    1989-01-01

    The development on application of biohydrometallargy to uranium ore processing is briefly introduced. The device designed for oxidizing ferrous ions in solution by using biomembrane, several bacterial leaching methods and the experimental results are given in this paper. The presented biohydrometallurgical process for recovering uranium includes bacterial leaching following by adsorption using tertiary amine resin 351 and oxidation of ferrous ions in the device with biomembranes. This process brings more economical benefits for treating silicate type original ores. The prospects on application of biogydrometallyurgy to solution mining is also discussed

  10. Infrared detection of ore variability that influences the environmental risks during perlite mining and processing

    NARCIS (Netherlands)

    Guatame Garcia, L.A.; Buxton, M.W.N.

    2017-01-01

    In the mining of perlite deposits, controlling the generation of fine particles and the concentration of metals is of outstanding importance to meet the environmental and market requirements. Particle size and chemical purity are conventionally manipulated during the processing of the ore to achieve

  11. Influence of some ions on the apatite flotation of Itataia ore

    International Nuclear Information System (INIS)

    Aquino, J.A. de.

    1987-01-01

    The production process by flotation for uranium phosphor ore in Itataia-Ce, Brazil is shown. A flotation scheme with mass balance and characterization on the samples is analyzed. The analysis methods with some results of concentration effect of Ca 2+ , Mg 2+ , Cl - e Na + in the direct flotation are demonstrated. (M.J.C.) [pt

  12. Preconcentration of low-grade uranium ores with environmentally acceptable tailings, part I

    International Nuclear Information System (INIS)

    Raicevic, D.; Raicevic, M.; McCarthy, D.R.

    1979-08-01

    The low-grade ore sample used for this investigation originated from Agnew Lake Mines Limited, Espanola, Ontario. It contained about 1% pyrite and 0.057% uranium, mainly as uranothorite with a small amount of brannerite. Both of these minerals occur in the quartz-sericite matrix of a conglomerate. A preconcentration process has been developed to give a high uranium recovery, reject pyrite, radium and thorium from the ore and produce environmentally acceptable tailings. This process applies flotation in combination with high intensity magnetic separation and gravity concentration

  13. The determination of radium-226 in uranium ores and mill products by alpha energy spectrometry

    International Nuclear Information System (INIS)

    Zimmerman, J.B.; Armstrong, V.C.

    1975-12-01

    A reliable routine procedure for determining 226 Ra by alpha energy spectrometry is described. Radium is isolated as sulphate from the sample matrix by co-precipitation with a small mass of barium and analysed using a ruggedized silicon surface barrier detector. The method is capable of providing high accuracy over a large 226 Ra concentration range and is applicable to materials such as uranium ores, uranium mill products and effluent streams. Samples resulting from nitric acid leach experiments with Elliot Lake ores were examined using the procedure. The distribution of 223 Ra, 224 Ra and 226 Ra between the leach products, (residue and leach liquor), is discussed. (author)

  14. Modifier free supercritical fluid extraction of uranium from sintered UO2, soil and ore samples

    International Nuclear Information System (INIS)

    Kanekar, A.S.; Pathak, P.N.; Acharya, R.; Mohapatra, P.K.; Manchanda, V.K.

    2011-01-01

    Direct extraction of uranium from different samples viz. sintered UO 2 , soil and ores was carried out by modifier free supercritical fluid using tri-n-butyl phosphate-nitric acid (TBP-HNO 3 ) adduct as extractant. These studies showed that pre-equilibration with more concentrated nitric acid helps in better dissolution and extraction of uranium from sintered UO 2 samples. Modifier free supercritical fluid extraction appears attractive with respect to minimization of secondary wastes. This method resulted 80-100% extraction of uranium from different soil/ore samples. The results were confirmed by performing neutron activation analysis of original (before extraction) and residue (after extraction) samples. (author)

  15. The role of magmas in the formation of hydrothermal ore deposits

    Science.gov (United States)

    Hedenquist, Jeffrey W.; Lowenstern, Jacob B.

    1994-01-01

    Magmatic fluids, both vapour and hypersaline liquid, are a primary source of many components in hydrothermal ore deposits formed in volcanic arcs. These components, including metals and their ligands, become concentrated in magmas in various ways from various sources, including subducted oceanic crust. Leaching of rocks also contributes components to the hydrothermal fluid—a process enhanced where acid magmatic vapours are absorbed by deeply circulating meteoric waters. Advances in understanding the hydrothermal systems that formed these ore deposits have come from the study of their active equivalents, represented at the surface by hot springs and volcanic fumaroles.

  16. Practice and prospect on bioleaching of uranium ore in China

    International Nuclear Information System (INIS)

    Liu Jian; Fan Baotuan; Meng Yunsheng; Zheng Ying; Liu Chao; Zhou Lei

    2008-01-01

    Developing situation on bioleaching of uranium ore in China is introduced. The selection and domestication of bacteria, development and application of biocntact oxidation tank, and practice on bioleaching of uranium ore in China are retrospeted and prospected. (authors)

  17. Measurement and Modelling of Blast Movement to Reduce Ore ...

    African Journals Online (AJOL)

    user

    geologists at Newmont Ahafo Mine have realised the impact of blast movement on ore losses and dilution and have ... Movement to Reduce Ore Losses and Dilution at Ahafo Gold Mine in Ghana”, Ghana Mining Journal, pp. .... classification.

  18. Flocculation of chromite ore fines suspension using polysaccharide ...

    Indian Academy of Sciences (India)

    Unknown

    liquid separation. Keywords. Flocculation; graft copolymer; mineral industry effluent; chromite ore fines; ... work well as flocculating agent on coal washery effluent, copper and iron ore fines etc (Karmakar et al 1998, 1999;. Tripathy et al 2001).

  19. Beneficiation strategy for some low grade ores of strategic metals in India

    International Nuclear Information System (INIS)

    Krishna Rao, N.

    1997-01-01

    In developing indigenous resources of strategic metals, beneficiation strategy has a major role to play, particularly where the ores are of low tenor. Presently India imports most of its requirements of metals like tin, tungsten, molybdenum, nickel and cobalt. In all these cases important low grade resources occur in the country. Beneficiation strategy necessary for exploitation of these deposits are discussed based mainly on vast batch and semi plant scale data generated in the Ore Dressing Section of Bhabha Atomic Research Centre. Also discussed is the case of strategic metal uranium where, in certain cases pre-concentration by beneficiation has the potential to make it feasible the exploitation of otherwise difficult to process ore resources. (author)

  20. Modelling Of Monazite Ore Break-Down By Alkali Process Spectrometry

    International Nuclear Information System (INIS)

    Visetpotjanakit, Suputtra; Changkrueng, Kalaya; Pichestapong, Pipat

    2005-10-01

    A computer modelling has been developed for the calculation of mass balance of monazite ore break-down by alkali process at Rare Earth Research and Development Center. The process includes the following units : ore digestion by concentrate NaOH, dissolution of digested ore by HCl, uranium and thorium precipitation and crystallization of Na3PO4 which is by-product from this process. The model named RRDCMBP was prepared in Visual Basic language. The modelling program can be run on personal computer and it is interactive and easy to use. User is able to choose any equipment in each unit process and input data to get output of mass balance results. The model could be helpful in the process analysis for the further process adjustment and development

  1. Alkaline sulfide pretreatment of an antimonial refractory Au-Ag ore for improved cyanidation

    Science.gov (United States)

    Alp, Ibrahim; Celep, Oktay; Deveci, Haci

    2010-11-01

    This paper presents the alkaline sulfide pretreatment of an antimonial refractory gold and silver ore. In the ore, gold occurs mainly as gold-silver alloys and as associated with quartz and framboidal pyrite grains, and, to a small extent, as the inclusions within antimonial sulfides. Silver is present extensively as antimonial sulfides such as andorite. Alkaline sulfide pretreatment was shown to allow the decomposition of the antimonial sulfide minerals (up to 98% Sb removal) and to remarkably improve the amenability of gold (e.g., from leaching. An increase in reagent concentration (1-4 mol/L Na2S or NaOH) and temperature (20-80°C), and a decrease in particle size seem to produce an enhancing effect on metal extraction. These findings suggest that alkaline sulfide leaching can be suitably used as a chemical pretreatment method prior to the conventional cyanidation for antimonial refractory gold and silver ores.

  2. Beneficiation and agglomeration of manganese ore fines (an area so important and yet so ignored)

    Science.gov (United States)

    Sane, R.

    2018-01-01

    Unpredictable changes in demand and prices varying from very attractive to depressing levels have thrown all Manganese ore mines out of normal operating gear. The supply has to be in time-bound fashion, of dependable quality and continuous. With setting-up of numerous small units and with existing ferro-alloy units, ore supply has become extremely sensitive issue. Due to unpredictable swing in price of Mn ore lumps, furnace operators found it economic and convenient to use fines, even at great risks to furnace equipment and operating persons and therefore risks & damages were conveniently & comfortably ignored. Beneficiation Cost(Operating) approx. - (ferruginous ore) - Roast reduction followed by magnetic separation route-particulars - Water 20/-, Power 490/-, Coal fines-675/-, OH-250/-totaling to Rs.1435/T. (Figures are based on actual data from investigations on Orissa & Karnataka sector ores). Feed Grade Mn- 28 to 32 %, Fe - 14 to 25 %, Concentrate (Beneficiated ore fines)- - Mn- 45 to 48 %, Fe - 6 to 8 %., Recovery - 35 %, Price of 28-30 % Mn ore fines = Rs. 2400/T, Cost of Concentrated fines (45/48% Mn grade) = Rs. 8300/T, Price of 47-48 % Mn Lumpy ore = Rs.11,000/T. Sintering Cost (Operating) - Approx-Rs.1195=00/T Sinter. Therefore cost of Sinter produced from beneficiated concentrate is 9130+1195 = Rs. 10325. The difference in cost of 48%Mn ore Lumps & 48%Mn sintered concentrate = 11000-10325 = Rs.675/T. The main purpose of this paper is to show that establishment of beneficiation unit & Sintering unit is economically feasible. There are many misconcepts, still prevailing, about use of Mn ore sinters. Few of the main misconcepts are- 1)Sinters bring no benefit - technical or economical.2) Sinters are very friable and disintegrate easily into high fines during handling/transportation. 3) Fines below 100 mesh cannot be sintered. 4) Silica increases to high level during sintering, resulting in to high slag volume thereby higher power consumption. All are false

  3. Porphyry-Copper Ore Shells Form at Stable Pressure-Temperature Fronts Within Dynamic Fluid Plumes

    Science.gov (United States)

    Weis, P.; Driesner, T.; Heinrich, C. A.

    2012-12-01

    Porphyry-type ore deposits are major resources of copper and gold, precipitated from fluids expelled by crustal magma chambers. The metals are typically concentrated in confined ore shells within vertically extensive vein networks, formed through hydraulic fracturing of rock by ascending fluids. Numerical modeling shows that dynamic permeability responses to magmatic fluid expulsion can stabilize a front of metal precipitation at the boundary between lithostatically pressured up-flow of hot magmatic fluids and hydrostatically pressured convection of cooler meteoric fluids. The balance between focused heat advection and lateral cooling controls the most important economic characteristics, including size, shape, and ore grade. This self-sustaining process may extend to epithermal gold deposits, venting at active volcanoes, and regions with the potential for geothermal energy production.

  4. Heap leaching of clay ish uranium ores

    International Nuclear Information System (INIS)

    Gonzalez, E.; Sedano, A.

    1973-01-01

    This paper describes an experimental facility, built near El Lobo mine. In it we study the beneficiation of low-grade uranium ore. The mineral has a great amount of clay and fines. The flow-sheet used has four steps: head leaching, ph-ajustement, ion-exchange and participation. We show, also, the most interesting results. (Author)

  5. PROCESS OF RECOVERING URANIUM FROM ITS ORES

    Science.gov (United States)

    Galvanek, P. Jr.

    1959-02-24

    A process is presented for recovering uranium from its ores. The crushed ore is mixed with 5 to 10% of sulfuric acid and added water to about 5 to 30% of the weight of the ore. This pugged material is cured for 2 to 3 hours at 100 to 110 deg C and then cooled. The cooled mass is nitrate-conditioned by mixing with a solution equivalent to 35 pounds of ammunium nitrate and 300 pounds of water per ton of ore. The resulting pulp containing 70% or more solids is treated by upflow percolation with a 5% solution of tributyl phosphate in kerosene at a rate equivalent to a residence time of about one hour to extract the solubilized uranium. The uranium is recovered from the pregnant organic liquid by counter-current washing with water. The organic extractant may be recycled. The uranium is removed from the water solution by treating with ammonia to precipitate ammonium diuranate. The filtrate from the last step may be recycled for the nitrate-conditioning treatment.

  6. Cationic flotation of some lithium ores

    International Nuclear Information System (INIS)

    Valadao, G.E.S.; Peres, A.E.C.; Silva, H.C. da

    1984-01-01

    The cationic flotation of some lithium ores (spodumene, amblygonite, petalite, lepidolite) is studied by the measure of zeta potential and micro-flotation tests in Hallimond tube. The effect of some modifier agents (corn starch, meta sodium silicate) on the lithium flotation is studied. (M.A.C.) [pt

  7. Flotation of uraniferous phosphorus ore from Itataia

    International Nuclear Information System (INIS)

    Aquino, J.A. de

    1984-01-01

    Flotation conditions, in laboratory and pilot scale, were established in a sample of Itataia uraniferous phosphorus ore which was basically constitute of apatite and calcite. The system of reagents-tall oil, collamil and sodium silicate-was studied in rougher, scavenger and cleaner stage. (M.A.C.) [pt

  8. Ferrite grade iron oxides from ore rejects

    Indian Academy of Sciences (India)

    Iron oxyhydroxides and hydroxides were synthesized from chemically beneficiated high SiO2/Al2O3 low-grade iron ore (57.49% Fe2O3) rejects and heated to get iron oxides of 96–99.73% purity. The infrared band positions, isothermal weight loss and thermogravimetric and chemical analysis established the chemical ...

  9. Production of thorium nitrate from uranothorianite ores

    International Nuclear Information System (INIS)

    Brodsky, M.; Sartorius, R.; Sousseuer, Y.

    1959-01-01

    The separation of thorium and uranium from uranothorianite ores, either by precipitation or solvent-extraction methods, are discussed, and an industrial process for the manufacture of thorium nitrate is described. Reprint of a paper published in 'Progress in Nuclear Energy' Series III, Vol. 2 - Process Chemistry, 1959, p. 68-76 [fr

  10. Price, technology, and ore reserves, ch. 2

    International Nuclear Information System (INIS)

    McAllister, A.L.

    1976-01-01

    Factors determining ore reserves in view of future uses are investigated: existing mining technologies, new techniques, price-technology relationship, effects of the use of different energy sources, exploration techniques, and price change are discussed. The effect of price and technology on reserves of specific commodities is dealth with. A section is also devoted to uranium

  11. Molybdenum extraction from copper-molybdenum ores

    International Nuclear Information System (INIS)

    Nevaeva, L.M.

    1982-01-01

    Molybdenum extraction from copper-molybdenum ores as practised in different countries is reviewed. In world practice the production process including depression of copper and iron sulfides and flotation of molybdenite is widely spread. At two USA factories the process of a selective flotation with molybdenite depression by dextrin is used

  12. Understanding Lateritic Ore Agglomeration Behaviour as a ...

    African Journals Online (AJOL)

    Processing such ores through cost-competitive heap (4-10 m high) leaching as an alternative, requires successful agglomeration of the feed into robust and porous granules. To date, produc-ing of granules with desirable attributes poses a major geotechnical challenge to industry. In the present work, we investigate ...

  13. Obtainment of tantalum oxide from national ores

    International Nuclear Information System (INIS)

    Pinatti, D.G.; Ribeiro, S.; Martins, A.H.

    1988-01-01

    The experimental results of tantalum oxides (Ta 2 O 5 ) obtainment from Brazilian ores of tantalite and columbite are described. This study is a part of the technologic and scientific research design of refractory metals (Ti, Zr, Hf, V, Nb, Ta, Cr, Mo and W) and correlate ceramics. (C.G.C.) [pt

  14. Economic outlook for radiometric selection of ores

    International Nuclear Information System (INIS)

    Formery, P.; Ziegler, V.

    1958-01-01

    The value of an ore can be increased by cutting off it's poor fractions. This selection may be realized at two stages: - part of the ore in situ is unable to cover it's extraction and treatment costs, this defines the 'underground cut-off grade'; - another portion of already extracted ore is unable to cover it's transport and treatment costs; this defines the 'surface cut off grade'. These selections are easily feasible owing to the property of uranium ores of emitting gamma radiations. A diagram makes possible a fast forecast on the effect of this selection upon the weight and metal yields. An attempt is made as well in order to provide the expected effect of the composition of underground cut off and surface cut off. This cut off however, being realized through an appreciation of the radiations, involves an alteration of the weight and metal yields which calls for a correction. A survey of the economic interest of the cut-off is done and an example of valorisation in a given deposit of a section at the limit of operability is proposed. (author) [fr

  15. A procedure for acid leaching of ores of the sandstone type, particularly of uranium ores

    International Nuclear Information System (INIS)

    Fiala, P.; Baloun, S.; Hinterholzinger, O.

    1990-01-01

    Ore mixed with the enriched fraction of the leached ore is leached with sulfuric acid at 5 to 220 degC. Bulky particles are sorted out from the mixture and reduced in size, and particles with a higher proportion of the useful component are separated from them. The latter particles constitute the enriched fraction of the leached ore, which is partially or completely returned to the mixture with the entering ore. The sorting should preferably be performed in an aqueous system. The assets of this procedure include a better homogenization of the mixture with the acid, a better stability of the reaction mixture which brings about reduced adhesion and solidification, and the possibility of extending the reaction time and increasing the temperature. The reduction in size makes for a better access of the leaching agent to the useful minerals, and the returning of the leachate to the reaction system spares sulfuric acid. (M.D.)

  16. A procedure for oxidation during the acid leaching of non-ferrous ores, particularly uranium ores

    International Nuclear Information System (INIS)

    Zubcek, L.; Baloun, S.; Martinek, K.; Vebr, Z.; Krepelka, J.; Lasica, S.

    1989-01-01

    It is suggested that dust from the production of ferroalloys of manganese, particularly ferrosilicomanganese and ferromanganese, can be conveniently used for oxidation during the acid leaching of non-ferrous ores, particularly uranium ores. This dust contains 30 to 40% oxides of manganese, about one-half of this is MnO 2 . Iron in the dust is present in the trivalent form, and the dust is pefectly dry. The conventional grinding of oxidants for the ore processing is eliminated, the dust being available in particle size below 0.2 mm. The dust is added in amounts of 5 to 100 kg per ton of the ore, and the suspension is typically heated at 115 degC for 3.5 hr. (P.A.)

  17. Geochemical Peculiarities of Galena and Sphalerite from Polymetallic Deposits of the Dal'negorskii Ore Region (Primorsky Krai, Russia)

    Science.gov (United States)

    Rogulina, L. I.; Moiseenko, V. G.; Ponomarchuk, V. A.

    2018-04-01

    New data on the composition of the major minerals from the skarn and vein polymetallic deposits of the Dal'negorskii ore region are reported. Analysis of galena and sphalerite was carried out by the X-ray fluorescent energy-dispersive method of synchrotron radiation for the first time. It is shown that the minor elements in major minerals of different deposits are typomorphic. Among these elements are Fe, Cu, Ni, Cd, Ag, Sn, and Sb, as well as In in sphalerite and Te in galena. The high concentrations of Ag, Cu, Te, Cd, and In in the extracted minerals indicate the complex character of mineralization. The compositional patterns of ore minerals characterize the sequence of mineral formation from the skarn to vein ores, and the sequence of deposits from the mesothermal to epithermal conditions. This provides geochemical evidence for the stage model of the formation of mineralization in the Dal'negorskii ore region.

  18. The impact of bacteria of circulating water on apatite-nepheline ore flotation.

    Science.gov (United States)

    Evdokimova, G A; Gershenkop, A Sh; Fokina, N V

    2012-01-01

    A new phenomenon has been identified and studied-the impact of bacteria on the benefication process of non-sulphide ores using circulating water supply-a case study of apatite-nepheline ore. It is shown that bacteria deteriorate the floatability of apatite due to their interaction with active centres of calcium-containing minerals and intense flocculation, resulting in a decrease of the flotation process selectivity thus deteriorating the quality of concentrate. Based on the comparative analysis of primary sequences of 16S rRNA genes, there have been identified dominating bacteria species, recovered from the circulating water used at apatite-nepheline concentrating mills, and their phylogenetic position has been determined. All the bacteria were related to γ-Proteobacteria, including the Acinetobacter species, Pseudomonas alcaliphila, Ps. plecoglossicida, Stenotrophomonas rhizophila. A method of non-sulphide ores flotation has been developed with consideration of the bacterial factor. It consists in use of small concentrations of sodium hypochlorite, which inhibits the development of bacteria in the flotation of apatite-nepheline ores.

  19. Hydrometallurgical Process and Kinetics of Leaching Manganese from Semi-Oxidized Manganese Ores with Sucrose

    Directory of Open Access Journals (Sweden)

    Yuhong Wang

    2017-02-01

    Full Text Available The extraction of manganese from a semi-oxidized manganese ore was investigated with sucrose as the reducing agent in dilute sulfuric acid medium. The kinetics of leaching manganese from the complex ore containing MnCO3 and MnO2 was also investigated. The effects of sucrose and sulfuric acid concentrations, leaching temperature and reaction time on the total Mn (TMn, MnO2 and MnCO3 leaching were investigated. Results showed that MnCO3 could more easily react with hydrogen ions than MnO2 in ores, and MnO2 decomposition could be advantageous for MnCO3 leaching. The leaching efficiencies of 91.8% for total Mn, 91.4% for MnO2 and 96.9% for MnCO3 were obtained under the following optimized conditions: 0.035 mol/L sucrose concentration, 5 mol/L sulfuric acid concentration, 60 min of reaction time and 363.2 K of leaching temperature. In addition, it was found that the leaching process of semi-oxidized manganese ore follows the shrinking core model and the leaching rate was controlled by chemical reaction and diffusion. The apparent activation energy of the total manganese, MnO2, and MnCO3 leaching were 40.83, 40.59, and 53.33 kJ·mol−1, respectively.

  20. Residues leaching from 'Factory of barren ores'

    International Nuclear Information System (INIS)

    Rakhmatov, N.; Khakimov, N.; Nazarov, Kh.M.; Barotov, A.M.

    2012-01-01

    The objective of the present work is safe management of residues from Factory of Barren Ores, their reprocessing, expenditures reduction for remediation of Istiklol city former uranium tailings. For this purpose, some experiences were adopted - Factory of Barren Ores tailing use for filling up the open pit where water with uranium content 3-5 mg/l is located. Factory of Barren Ores waste are passed through heap leaching and have some amount of uranium salts dissolved in water. Thus, we propose to dissolve uranium from Factory of Barren Ores wastes with uranium bearing water flowing out from gallery and filling up the open-pit by radioactive wastes. In so doing, uranium content flowing out from gallery will increase twice, and further, passing them through apricot's shell, as a sorbent, we will clean the water against radionuclides. Residue samples with uranium content 0,015% from Factory of Barren Ores and uranium bearing waters from gallery 1 with uranium content 0,0025 g/l were used for laboratory tests. After which, a slurry was prepared by means of residue mixing with water in ratio of solid and liquid phases (S:L) - 1:2 and 9,7 ml of sulfuric acid (Ρ=1,82) was added which corresponds consumption by H 2 SO 4 176,54 kg/t. For the first test, leaching was carried out during 4 hours at ph=1,6 at room temperature. For the second test, leaching was carried out at 60 d eg C a nd ph=1,6 during 4 hours. Slurry heating and mixing was carried out by means of magnetic mixer. The basic residue leaching indicators are provided in this article.

  1. Hydrogen Plasma Processing of Iron Ore

    Science.gov (United States)

    Sabat, Kali Charan; Murphy, Anthony B.

    2017-06-01

    Iron is currently produced by carbothermic reduction of oxide ores. This is a multiple-stage process that requires large-scale equipment and high capital investment, and produces large amounts of CO2. An alternative to carbothermic reduction is reduction using a hydrogen plasma, which comprises vibrationally excited molecular, atomic, and ionic states of hydrogen, all of which can reduce iron oxides, even at low temperatures. Besides the thermodynamic and kinetic advantages of a hydrogen plasma, the byproduct of the reaction is water, which does not pose any environmental problems. A review of the theory and practice of iron ore reduction using a hydrogen plasma is presented. The thermodynamic and kinetic aspects are considered, with molecular, atomic and ionic hydrogen considered separately. The importance of vibrationally excited hydrogen molecules in overcoming the activation energy barriers, and in transferring energy to the iron oxide, is emphasized. Both thermal and nonthermal plasmas are considered. The thermophysical properties of hydrogen and argon-hydrogen plasmas are discussed, and their influence on the constriction and flow in the of arc plasmas is considered. The published R&D on hydrogen plasma reduction of iron oxide is reviewed, with both the reduction of molten iron ore and in-flight reduction of iron ore particles being considered. Finally, the technical and economic feasibility of the process are discussed. It is shown that hydrogen plasma processing requires less energy than carbothermic reduction, mainly because pelletization, sintering, and cokemaking are not required. Moreover, the formation of the greenhouse gas CO2 as a byproduct is avoided. In-flight reduction has the potential for a throughput at least equivalent to the blast furnace process. It is concluded that hydrogen plasma reduction of iron ore is a potentially attractive alternative to standard methods.

  2. Monitoring shale in iron ore

    International Nuclear Information System (INIS)

    Aylmer, J.A.; Holmes, R.J.; Miles, J.G.

    1981-01-01

    Apparatus for determining the concentration of a radioactive constituent in a sample of material is claimed. It comprises: a radiation detector; a weightometer; and an electronic means to calculate the ratio of the intensity of the radiation monitored by the detector to the mass of the sample. Apparatus for sorting samples of a material on a conveyor in accordance with the concentration of a radioactive constituent is also claimed. It comprises: a low energy souce of gamma radiation positioned above the conveyor; a gamma detector positioned below the conveyor which can receive gamma radiation from the source and the constituent; an electronic calculator adapted to receive the output signals from the detector and to produce a signal representative of the ratio of the intensity of received characteristic radiation from a sample to the mass of a sample; and sorting means responsive to the output signal for controlling the destination of a sample on leaving the conveyor

  3. Uranium reduction by carbon oxide during ore formation

    International Nuclear Information System (INIS)

    Matyash, I.V.; Gavrusevich, I.B.; Pasal'skaya, L.F.; Shcherba, D.I.

    1981-01-01

    Using the method of gas chromatography the gas content in Pre-Cambrian granitoils of various types and in natrometasomatites associted with them is studied. It is established that granites associated with ore-bearing albitites have sharply elevated amounts of CO as compared with granites, which do not include mineralization. Simultaneously in ore samples the absence or sharply low amounts of CO as compared with ore-free samples is observed, that is reverse dependence of CO and ore components. Carbon oxide is the reducing agent of uranium mineralization and alongside with other reducing agents can be a geochemical barrier in the process of ore formation [ru

  4. Sinterization of manganese ore tailings under natural air

    Energy Technology Data Exchange (ETDEWEB)

    Lima, M.M.F.; Souza, L.G.P.R.M.F. [Universidade Federal de Ouro Preto (UFOP), MG (Brazil)

    2014-07-01

    The manganese ore has wide application in metallurgy. However, from each of three hundred concentrations found, only one can be seen as a deposit. The aim of this study was to obtain and characterize a sinter from manganese ore tailing. The tailing was milled, classified (<400 ⧣) and calcinated (800°C - 3600s). The mixture had 12% moisture, 7 and 9% of activated charcoal. After homogenization, the sintering were carried out at 1140, 1145 and 1150°C during 1800, 7200 and 14400s at natural air. The sintered products were characterized by EDS analysis, BET surface area, apparent density, X-rays diffraction and SEM/EDS. The mass loss was approximately 14% and 16% in the calcination and sintering, respectively, due to the elimination of volatile products and water. The main phases characterized: SiO2, silicate with high content of manganese in the matrix and other silicates with different proportions of Ti, Na, Mn, Mg and Ca. (author)

  5. Mining and milling of uranium ore: Indian scenario

    International Nuclear Information System (INIS)

    Bhasin, J.L.

    2001-01-01

    The occurrence of uranium minerals in Singhbhum Thrust belt of Eastern India has been known since 1937. In 1950, a team of geologists of the Atomic Minerals Division was assigned to closely examine this 160 km long belt. Since then, several occurrences of uranium have been found and a few of them have sufficient grade and tonnage for commercial exploitation. In 1967, the Government of India formed Uranium Corporation of India Ltd., under the administrative control of the Department of Atomic Energy, with the specific objective of mining and processing of uranium ore and produce uranium concentrates. At present the Corporation operates three underground uranium mines, one ore processing plant with expanded capacity, and two uranium recovery plants. Continuing investigations by the Atomic Mineral Division has discovered several new deposits and favourable areas. The most notable is the large Domiasiat deposit of the sandstone type found in the State of Meghalaya. This deposit is now being considered for commercial exploitation using the in-situ leaching technology. (author)

  6. Low grade uranium ores as potential sources of raw material

    International Nuclear Information System (INIS)

    Venzlaff, H.

    1976-01-01

    Reports on the uranium requirement and the uranium reserves show that, even if the demand were to be stretched out slightly, the rate of new discoveries of uranium would have to be doubled or even tripled within a few years in order to ensure supply. Despite some spectacular discoveries of large scale deposits in Australia it must be said that only very few truly new uranium provinces have been discovered over the past twenty years. In this situation more attention is now being devoted to low grade uranium depositis, to findings whose concentration does not exceed 1,000 ppm. These deposits contain quantities of uranium many times larger than the deposits that can now be mined at prices up to 30/lb of U 3 O 8 . Even now low grade uranium ore is being mined as a byproduct, with the actual valuable mineral producing most of the income from mining activities. However, if one strikes a balance in this situation, one finds that only part of the requirement can be met in this way. Hence, all possibilities must be exhausted to mine uranium as a byproduct, new techniques of uranium production from low grade ores must be developed, and also conventional prospection must be intensified, if the continuity of supply of the nuclear power stations in the eighties and nineties is to be guaranteed. (orig.) [de

  7. Geochemical prospecting techniques for ore deposits in periglacial regions

    International Nuclear Information System (INIS)

    Pitul'ko, V.M.

    1977-01-01

    Necessity and prospects of the implementation of geochemical methods of search in periglacial regions are discussed. The behaviour of chemical elements under the conditions of oxide and sulphate cryogenic topographies whose development has common regularities is analyzed. According to the specificity of migration the observed elements have been divided into four groups: active, mobile, low-mobile and inert migrants. Uranium which is present in ores in the form of pitchblende in oxide zones of the oxidation is actively redistributed. In zones of the oxidation of rare metal metasomatites connected with alkalic ultrabasic rocks only that part of U is mobile which being released from pyrochlore forms the regenerated uranium black and the partial enrichment of the iron gossan. Th like other elements of the 4-th group in all oxidation zones is observed to accumulate in minerals - concentrators: thorite, pyrochlore and so on. A diagram is plotted which characterizes the migration of elements whithin aureole landscapes as well as in automonous and dependent topographies of ore-free areas. The complex nature of secondary aureoles displays the most complete anomalous spectrum of elements - indicators of mineralization. The table of the most typical elements - indicators of the secondary scattering of some endogenic deposits of the cryolitic zone is given

  8. X-Ray Fluorescence Spectrometry. I. Determination of thorium in ores

    International Nuclear Information System (INIS)

    Bermudez Polonio, J.; Crus Castillo, F. de la; Fernandez Cellini, R.

    1961-01-01

    A X-ray spectrometric method has been developed for analysis of thorium in ores in the range of concentration from 0.01 to 0.5 percent ThO 2 , using selenium as a internal standard. The concentration of thorium is determined in a working curve prepared by plotting the percentage of ThO 2 against the ratio intensity of the Th Lα 1 line to Sek β 1 line. (Author) 17 refs

  9. High-rate behaviour of iron ore pellet

    Science.gov (United States)

    Gustafsson, Gustaf; Häggblad, Hans-Åke; Jonsén, Pär; Nishida, Masahiro

    2015-09-01

    Iron ore pellets are sintered, centimetre-sized spheres of ore with high iron content. Together with carbonized coal, iron ore pellets are used in the production of steel. In the transportation from the pelletizing plants to the customers, the iron ore pellets are exposed to different loading situations, resulting in degradation of strength and in some cases fragmentation. For future reliable numerical simulations of the handling and transportation of iron ore pellets, knowledge about their mechanical properties is needed. This paper describes the experimental work to investigate the dynamic mechanical properties of blast furnace iron ore pellets. To study the dynamic fracture of iron ore pellets a number of split Hopkinson pressure bar tests are carried out and analysed.

  10. Mineralogical and paragenetical problems of the Mecsek uranium ore

    International Nuclear Information System (INIS)

    Vincze, J.; Fazekas, V.

    1979-01-01

    The latest results of the ore-mineralogical examination of the uranium ore of a deposit included in Permian sandstones in the Mecsek Mountains, southern Hungary, are presented. The phases of the minerals belonging to the uranium oxide series and their types of development, the post-coffinite nasturan pseudomorphs and the relationship between nasturan and coffinite are dealt with. Of the sulphide ore minerals associated with uranium ore mineralization the type determinant mineral is pyrite, i.e. the mineral forming their bulk and partly represented by characteristically finely aggregated ''bacteriopyrite'' and/or spherical pyrite and ''framboidal pyrite. The textural pattern of the ore mineralization is of typically matrix type. The matrix of sandstone is constituted by carbonate minerals, ''hydromicas'' and ore minerals. The matrix and, consequently, the ore minerals will corrode and consume the allothigenic detrital rockforming minerals, the feldspar, quartz-porphyry and quartz. (A.L.)

  11. Cupriferous peat: embryonic copper ore

    Energy Technology Data Exchange (ETDEWEB)

    Fraser, D C

    1961-07-01

    A Canadian peat was found to contain up to 10% (dry weight) Cu, and a mechanism for Cu accumulation in peat was discussed. Wet chemical techniques and x-ray diffraction were utilized to identify Cu compounds. Copper was organically bound in peat as a chelate complex and did not occur as an oxide, sulfide, or as elemental Cu. Because of the low S content of peat the Cu was assumed to be bound to nitrogen or oxygen-containing components. Copper, having a greater affinity for N, tended to form the more stable Cu-N chelate. The element was concentrated as circulating cupriferous ground waters filtered through the peat.

  12. The applications of microwave energy to improve grindability and extraction of gold ores

    Energy Technology Data Exchange (ETDEWEB)

    Huang, J.H

    2000-10-01

    gold ore, in which gold was finely disseminated in pyrite and marcasite, was an extremely refractory gold ore. Without pretreatment, only 37{approx}39% of the gold could be extracted with sodium cyanide. However, this was improved after the head ores or floatation concentrates were pretreated by microwave radiation. 74.5{approx}81.2% of the gold was extracted from the microwave treated head ore. The hydrometallurgical pretreatment of pyrite and marcasite in a microwave field and a conventional heating environment was also investigated. In a nitric acid solution, pyrite and marcasite can be rapidly leached. Reaction temperature and the concentration of HNO{sub 3} had a significant influence on decomposition rate. Marcasite had a substantially higher decomposition rate than pyrite. Microwave heating could promote the dissociation of marcasite and pyrite, compared with conventional heating. This was caused by special volumetric heating during microwave exposure that may induce local overheating or improve the interactions between the high dielectric loss minerals and the leaching solution. Kinetic investigations show that the decomposition of both the minerals in a nitric acid medium is controlled by chemical reactions on the surfaces of particles. The decomposition is a second order reaction with respect to nitric acid concentration. Less than 5 {approx} 7% of the decomposed sulphur was transformed into elemental sulphur during the leaching of both the minerals. (author)

  13. The applications of microwave energy to improve grindability and extraction of gold ores

    International Nuclear Information System (INIS)

    Huang, J.H.

    2000-10-01

    gold was finely disseminated in pyrite and marcasite, was an extremely refractory gold ore. Without pretreatment, only 37∼39% of the gold could be extracted with sodium cyanide. However, this was improved after the head ores or floatation concentrates were pretreated by microwave radiation. 74.5∼81.2% of the gold was extracted from the microwave treated head ore. The hydrometallurgical pretreatment of pyrite and marcasite in a microwave field and a conventional heating environment was also investigated. In a nitric acid solution, pyrite and marcasite can be rapidly leached. Reaction temperature and the concentration of HNO 3 had a significant influence on decomposition rate. Marcasite had a substantially higher decomposition rate than pyrite. Microwave heating could promote the dissociation of marcasite and pyrite, compared with conventional heating. This was caused by special volumetric heating during microwave exposure that may induce local overheating or improve the interactions between the high dielectric loss minerals and the leaching solution. Kinetic investigations show that the decomposition of both the minerals in a nitric acid medium is controlled by chemical reactions on the surfaces of particles. The decomposition is a second order reaction with respect to nitric acid concentration. Less than 5 ∼ 7% of the decomposed sulphur was transformed into elemental sulphur during the leaching of both the minerals. (author)

  14. Neutron shielding properties of boron-containing ore and epoxy composites

    International Nuclear Information System (INIS)

    Li Zhifu; Xue Xiangxin

    2011-01-01

    Using the boron-containing iron ore concentrate and boron-rich slag as studying object, the starting materials were got after the specific green ore containing boron dressing in China and blast furnace separation respectively. Monte-Carlo method was used to study the effect of the boron-containing iron ore concentrate and boron-rich slag and their composites with epoxy on the neutron shielding abilities. The reasons that affecting the shielding materials properties was discussed and the suitable proportioning of boron-containing ore to epoxy composites was confirmed; the 14.1 MeV fast neutron removal cross section and the total thermal neutron attenuation coefficient were obtained and compared with that of the common used concrete. The results show that the shielding property of 14.1 MeV fast neutron is mainly concerned with the low-Z elements in the shielding materials, the thermal neutron shielding ability is mainly concerned with boron concentrate in the composite, the attenuation of the accompany γ-ray photon is mainly concerned with the high atom number elements content in the ore and the density of the shielding material. The optimum Janume fractions of composites are in the range of 0.4-0.6 and the fast neutron shielding properties are similar to concrete while the thermal neutron shielding properties are higher than concrete. The composites are expected to be used as biological concrete shields crack injection and filling of the anomalous holes through the concrete shields around the radiation fields or directly to be prepared as shielding materials.(authors)

  15. Bioleaching of a manganese and silver Ore

    International Nuclear Information System (INIS)

    Porro, S.; Tedesco, P.H.; La Plata

    1990-01-01

    The bioleaching with a strain of Thiobacillus thiooxidans of the ore of Farallon Negro (Catamarca, Argentina) was studied in order to estimate its application to the solution and recovery of the manganese, and to improve the silver extraction. The State company which works the mine has not yet found an economical process to extract the manganese and has only reached a 30% efficiency in the recovery of silver by cianuration. The effects of pulp density variations and the addition of different quantities of FeS were analysed looking for the best working conditions. 74 μm (mesh Tyler 200) of ore particles were used because that is the size used in this plant for the cianuration process. (Author)

  16. Introduction - Acid decomposition of borosilicate ores

    International Nuclear Information System (INIS)

    Mirsaidov, U.M.; Kurbonov, A.S.; Mamatov, E.D.

    2015-01-01

    The complex processing of mineral raw materials is an effective way for the extraction of valuable components. One of these raw materials are borosilicate ores from which the boric acid, aluminium and iron salts and building materials can be obtained. In the Institute of Chemistry of the Academy of Sciences of the Republic of Tajikistan the flowsheets of the processing of borosilicate raw materials by acid and chloric methods were elaborated. The acid methods of decomposition of borosilicate ores of Ak-Arkhar Deposit were considered in present monograph. The carried out researches on elaboration of physicochemical aspects and technological acid methods allowed to define the optimal ways of extraction of valuable products from borosilicate raw materials of Tajikistan.

  17. RL-1: a certified uranium reference ore

    International Nuclear Information System (INIS)

    Steger, H.F.; Bowman, W.S.

    1985-06-01

    A 145-kg sample of a uranium ore from Rabbit Lake, Saskatchewan, has been prepared as a compositional reference material. RL-1 was ground to minus 74 μm and mixed in one lot. Approximately one half of this ore was bottled in 100-g units, the remainder being stored in bulk. The homogeneity of RL-1 with respect to uranium and nickel was confirmed by neutron activation and X-ray fluorescence analytical techniques. In a 'free choice' analytical program, 13 laboratories contributed results for one or more of uranium, nickel and arsenic in one bottle of RL-1. Based on a statistical analysis of the data, the following recommended values were assigned: U, 0.201%; Ni, 185 μg/g; and As, 19.6 μg/g

  18. Modeling drying of iron ore pellets

    OpenAIRE

    Ljung, Anna-Lena

    2010-01-01

    Iron ore pellets are a highly refined product supplied to the steel making industry for use in blast furnaces or direct reduction processes. The use of pellets offers many advantages such as customer adopted products, transportability and mechanical strength yet the production is time and energy consuming. Being such, there is a natural driving force to enhance the pelletization in order to optimize production and improve quality. The aim with this thesis is to develop numerical models with w...

  19. A study on the upgrading by physical means of low grade uranium ore from Phu Wiang District

    International Nuclear Information System (INIS)

    Wihokratna, W.

    1980-01-01

    The purpose of this thesis is to upgrade the uranium ore at Phu Wiang district. Because of the fine grains and high degree of dissemination of uranium in ores, resulting practically complete envelopment of the uranium minerals by the gangue minerals, the ore must first undergo digestion in order to reveal the uranium minerals. After digestion, sodium hydroxide of 0.05 normal was added to the ore and the mixture was fed into the agitator provided with baffles and two specially designed propellers. Due to the 'Push - Pull' motion of the propellers a zone of specially high turbulence was created between them. Also in this region higher concentration of uranium is revealed and the high concentrated uranium ore was regularly stripped off for further analysis. It was found that by using mineral of grain size of 100 mesh and 0.0187% of uranium content a concentration up to 0.063% uranium content (an upgrading better than by a factor of three times) was achieved with the above method. The uranium content was analyzed with 3'' x 3'' NaI (Tl) detector and 1024 channels MCA

  20. Technological studies on the Manisa-Koprubasi uranium ores of Turkey

    International Nuclear Information System (INIS)

    Sagdik, U.

    1980-01-01

    At the end of the laboratory and pilot plant scale technological experiments, three main types of ore have been classified: (i) Kasar type: The ores consist of secondary uranium mineralization (autunite, meta-autunite and torbenite) in loosely consolidated sands, gravels and clays of Neogene Age. Heap leaching has been carried out on 100 and 1000 t ore samples (0.05% U 3 O 8 ) under economical conditions, such as 20 to 40 kg of H 2 SO 4 per tonne of ore at ambient temperature; original size -20 cm, solid/liquid ratio of 10, 20 days, and 90% recovery of uranium has been reached. The uraniferous solutions (1 to 2 g of U 3 O 8 per litre) obtained from the heap leaching operations were purified in a solvent extraction unit with a capacity of 100 ltr/h by using an Alamine 336-kerosene-decanol solution. The uranium in the purified and concentrated solutions (15 g of U 3 O 8 per litre) was then precipitated as a yellow cake with 65 to 75% U 3 O 8 content by means of magnesia milk. (ii) Tasharman type: No specific uranium mineral has been detected in the mineralogical determination, although uranium is disseminated in phosphate minerals as dahllite and apatite. Uranium in the ore has been leached under rather uneconomical conditions; 100 kg of H 2 SO 4 per tonne of ore, particle size -1 cm, 25 0 C, 30 days. In the SX-treatment of pregnant solutions phosphate ions, higher acidity than pH 1, and compounds formed as a chemical precipitation, hindered the SX-recoveries. In such cases, the addition of acid, dilution of pregnant solutions, membrane filtration, or 40 0 C temperature have been applied to decrease the uranium loss in the raffinate. (iii) Carbonate type: Even if alkaline leaching at 65 0 C, or leaching with 400 kg of H 2 SO 4 per tonne of ore, was carried out on -200 mesh ore samples, no acceptable uranium recoveries were obtained

  1. Remediation of Canada's historic haul route for radium and uranium ores - the northern transportation route - 59303

    International Nuclear Information System (INIS)

    Geddes, Brian; Wenzel, Chris; Owen, Michael; Gardiner, Mark; Brown, Julie

    2012-01-01

    Established in the 1930's, the Northern Transportation Route (NTR) served to transport pitchblende ore 2,200 km from the Port Radium Mine in Canada's Northwest Territories to Fort McMurray in Alberta. From there, the ore was shipped 3,000 km by rail to the Town of Port Hope, Ontario, where it was refined for its radium content and used for medical purposes. Later, transport and refinement focussed on uranium. The corridor of lakes, rivers, portages and roads that made up the NTR included a number of transfer points, where ore was unloaded and transferred to other barges or trucks. Ore was occasionally spilled during these transfer operations and, in some cases, subsequently distributed over larger areas as properties were re-developed or modified. In addition, relatively small volumes of ore were sometimes transported by air to the south. Since 1991, the Low-Level Radioactive Waste Management Office (LLRWMO), working with communities and its consulting contractors, has conducted surveys to identify and characterize spill sites along the NTR where soils exhibit elevated concentrations of uranium, radium and/or arsenic. In addition to significant areas of impact in Fort McMurray, contamination along the NTR was centered in the Sahtu region near Great Bear Lake and along the southern part of the Slave River. Early radiological investigations found contaminated buildings and soil and occasionally discrete pieces of pitchblende ore at many transfer points and storage areas along the NTR. Where possible, survey work was undertaken in conjunction with property redevelopment activity requiring the relocation of impacted soils (e.g., at Tulita, Fort Smith, Hay River, and Fort McMurray). When feasible to consolidate contaminated material locally, it was placed into Long Term Management Facilities developed to manage and monitor the materials over extended timelines. Radiological activity generated by these engineered facilities are generally below thresholds established by

  2. The redox reaction kinetics of Sinai ore for chemical looping combustion applications

    International Nuclear Information System (INIS)

    Ksepko, Ewelina; Babiński, Piotr; Nalbandian, Lori

    2017-01-01

    Highlights: • Redox reaction kinetics of Fe-Mn-rich Sinai ore was determined by TGA. • The most suitable model for reduction was D3, while R3 for oxidation. • Activation energies 35.3 and 16.70 kJ/mole were determined for reduction and oxidation. • Repetitive redox reactions favor the formation of spinel phases in Sinai ore. • Multiple redox cycles induce formation of extensive porosity of the particles. - Abstract: The objective of this work was to study the use of Sinai ore, a Fe–Mn-based ore from Egypt, as a low-cost oxygen carrier (OC) in Chemical Looping Combustion (CLC). The Sinai ore was selected because it possesses relatively high amounts of iron and manganese oxides. Furthermore, those oxides have low cost, very favorable environmental and thermodynamic properties for the CLC process. The performance of the Sinai ore as an OC in CLC was compared to that of ilmenite (Norway Tellnes mine), the most extensively studied naturally occurring Fe-based mineral. The kinetics of the reduction and oxidation reactions with the two minerals were studied using a thermogravimetric analyzer (TGA). Experiments were conducted under isothermal conditions, with multiple redox cycles, at temperatures between 750 and 950 °C. For the reduction and oxidation reactions, different concentrations of CH_4 (10–25 vol.%) and O_2 (5–20 vol.%) were applied, respectively. The kinetic parameters, such as the activation energy (E_a), pre-exponential factor (A_0), and reaction order (n), were determined for the redox reactions. Furthermore, models of the redox reactions were selected by means of a model-fitting method. For the Sinai ore, the D3 model (3-dimensional diffusion) was suitable for modeling reduction reaction kinetics. The calculated E_a was 35.3 kJ/mole, and the reaction order was determined to be approximately 0.76. The best fit for the oxidation reaction was obtained for the R3 model (shrinking core). The oxidation (regeneration) reaction E_a was equal to 16

  3. Geology of eastern Smith Lake ore trend, Grants mineral belt

    International Nuclear Information System (INIS)

    Ristorcelli, S.J.

    1980-01-01

    The sandstones in the Brushy Basin Member of the Morrison Formation (Jurassic) are the ore-bearing horizons of the eastern Smith Lake area. The Brushy Basin Member in this district consists of three sandstones with interbedded mudstones. Only the lower two sandstones contain ore. The sandstones are fine to coarse grained, well rounded, and arkosic, representing continental stream sediments. The lower sandstone contains rollfront ore. The redox interface is laterally extensive and well defined, extending at least 7 mi (11 km) west of the Bluewater fault zone. The ore generally occurs at the redox boundary but occasionally will be up to 1500 ft (450 m) updip. Limonitic alteration, where present, is downdip from the hematitic zone and is 100-1,500 ft (30 to 450 m) wide. The middle sandstone contains both trend ore and roll-front ore. The trend ore occurs downdip from the redox front in unoxidized ground. The redox front in the middle sand is also laterally extensive but displays a wedge shape, rather than a C shape. The clay assemblages of the two types of ore are different: the trend ore occurs in sands with the pore spaces filled with kaolinite; the roll-front ore is associated with altered illite-montmorillonite as grain coatings. Hematitic alteration is asociated with the latter. A second stage of kaolinite coats the illite-montmorillonite. Two periods of mineralization are suggested, but no absolute dates are known. The trend ore is the oldest (Jurassic) and is similar to the ore found in unoxidized ground elsewhere in the Grants region. The rollfront ore could be Laramide or post-Laramide because of its association with local Laramide structures

  4. Real-time microradiology of disintegration of iron ore sinteres

    International Nuclear Information System (INIS)

    Kim, Jong Ryun; Kang, H.S.; Lee, Ho Jun; Je, Jung Ho; Jeong, S.K.; Tsai, W.-L.; Hsu, P.C.; Hwu, Y.

    2003-01-01

    We first present real-time microradiology of disintegration of self-fluxing iron ore sinters in low temperature reduction using highly collimated synchrotron source. The experiments were performed on the 5C1 beamline at PLS (Pohang Light Source, Pohang, Korea), operating at 2.5 GeV. We used unmonochromatized ('white') light with no optical elements except beryllium windows. The images of the crack superimpose, on the two-dimensional projection of a three-dimensional phenomenon, suggest that cracks are always initiated from pores in the sinters and propagate along neighboring pores. Interestingly, cracking occurs mostly on macropores (>800 μm), preferentially initiated from stress concentrated sites on pore surfaces. This dynamic study of the disintegration of sinters clearly shows that the crack initiation temperature is as low as 450 deg. C

  5. Steady-state optimization of ore-dressing plants

    International Nuclear Information System (INIS)

    Niemi, A.J.

    1989-01-01

    The ore-dressing plant consists of the steps of grinding and flotation. Its optimization is based on steady state simulation of the mass balances with a plant model. The model data are obtained by tracer tests and analysis. An evaluation of performance of the plant has to observe the recovery of the valuable mineral, the throughput of the system and the grade of the concentrate which are outputs of the flotation plant. Simulation with the flotation plant model yields that combination of values of controllable inputs to flotation which corresponds to an optimal operation of the conditioning an flotation system, for a specified feed and its fractional composition. Simulations for other feeds and compositions advise how they should be chosen, for a better overall performance. (author)

  6. Beneficiation studies of an uranium siliceous - phosphate ore

    International Nuclear Information System (INIS)

    Bruno, J.B.; Santos, A.T.; Santos Benedetto, J. dos

    1980-01-01

    The consolidation of the beneficiation studies of a low-grade uranium siliceous - phosphate ore (11% P 2 O 5 ) from Itataia region in the Northeast of Brazil, owned by Empresas Nucleares Brasileiras S.A. - NUCLEBRAS, are presented. Laboratory studies using froth flotation technique and applying statistical methods for data evaluation were made. Pilot plant tests in a 120 Kg/h scale were conducted as a consequence of the bench scale tests. The developed process using tall-oil as collector and starch as depressant gave a total yield of 80% for the P 2 O 5 and 71% the U 3 O 8 , for a 33% P 2 O 5 phosphate concentrate. (Author) [pt

  7. Advances and Opportunities in Ore Mineralogy

    Directory of Open Access Journals (Sweden)

    Nigel J. Cook

    2017-11-01

    Full Text Available The study of ore minerals is rapidly transforming due to an explosion of new micro- and nano-analytical technologies. These advanced microbeam techniques can expose the physical and chemical character of ore minerals at ever-better spatial resolution and analytical precision. The insights that can be obtained from ten of today’s most important, or emerging, techniques and methodologies are reviewed: laser-ablation inductively-coupled plasma mass spectrometry; focussed ion beam-scanning electron microscopy; high-angle annular dark field scanning transmission electron microscopy; electron back-scatter diffraction; synchrotron X-ray fluorescence mapping; automated mineral analysis (Quantitative Evaluation of Mineralogy via Scanning Electron Microscopy and Mineral Liberation Analysis; nanoscale secondary ion mass spectrometry; atom probe tomography; radioisotope geochronology using ore minerals; and, non-traditional stable isotopes. Many of these technical advances cut across conceptual boundaries between mineralogy and geochemistry and require an in-depth knowledge of the material that is being analysed. These technological advances are accompanied by changing approaches to ore mineralogy: the increased focus on trace element distributions; the challenges offered by nanoscale characterisation; and the recognition of the critical petrogenetic information in gangue minerals, and, thus the need to for a holistic approach to the characterization of mineral assemblages. Using original examples, with an emphasis on iron oxide-copper-gold deposits, we show how increased analytical capabilities, particularly imaging and chemical mapping at the nanoscale, offer the potential to resolve outstanding questions in ore mineralogy. Broad regional or deposit-scale genetic models can be validated or refuted by careful analysis at the smallest scales of observation. As the volume of information at different scales of observation expands, the level of complexity

  8. Acid pre-treatment method for in situ ore leaching

    International Nuclear Information System (INIS)

    Mallon, R.G.; Braun, R.L.

    1975-01-01

    An acid leaching method is described for the recovery of a desired element from a subterranean rubblized body of primary ore containing the element and also having associated therewith a carbonate mineral wherein the rubblized ore body is flooded with an aqueous acidic solution in order to release carbon dioxide from the associated carbonate mineral. After a substantial portion of the available carbon dioxide is released and removed from the ore body, as by venting to the atmosphere, an oxidizing gas is introduced into the flooded, rubblized ore to oxidize the ore and form an acid leach solution effective in the presence of the dissolved oxidizing gas to dissolve the ore and cause the desired element to go into solution. The leach solution is then circulated to the surface where the metal values are recovered therefrom

  9. EXPLANATORY MODEL OF SPOT PRICE OF IRON ORE

    Directory of Open Access Journals (Sweden)

    Juan Enrique Villalva A.

    2015-11-01

    Full Text Available The objective of this study was to construct an explanatory model of the spot price of iron ore in the international market. For this, the method of multiple linear regressions was used. As a dependent variable, the spot price of iron ore (62% Fe China Tianjin port was taken, between 2010 and 2013. As independents variables were taken seven variables of international iron ore market. The resulting model includes variables: Iron ore inventory in Chinese ports, Baltic Dry Index (BDI, Iron ore exports from Brazil & Australia and Chinese Rebar Steel Price, as explanatory variables of the behavior of the spot price of iron ore in the international market. The model has an adjusted coefficient of determination R2 of 0.90, and was validated by comparing its predictions vs. known values of 2014.

  10. Application of isotope techniques to groundwater pollution research for Xiangshan uranium ore field, China

    International Nuclear Information System (INIS)

    Liu Fulin; Liu Peilun; Zhu Chuande; Wu Xiaowei; Zeng Yinsheng

    1998-01-01

    The investigation of groundwater pollution due to uranium deposits focused on the most important uranium metallogenic area-Zhoujiashan district of Xiangshan uranium ore field, China. Groundwater collected from five completed exploration boreholes in the area is regarded as the pollution source and is traced and analysed by using isotope as well as radio-hydrochemical techniques. In addition, the pollution situation of a small uranium ore pile for heap-leaching and a big uranium ore open pit are monitored by the same techniques. It has been experimentally proven that the uranium concentration and the uranium isotope ratio 234 U/ 238 U in natural waters are two sensitive indicators of radioactive pollution in natural waters. It was concluded that under present conditions, exploration of uranium deposits may not cause serious groundwater pollution of radioactive elements (U, Ra, Rn and Th), however, it is difficult to avoid the serious surface water pollution coming from the exploitation of uranium ore by a big open pit. (author)

  11. Preparation of precipitated barium sulphate from Egyptian barytes ore and its application in paints

    International Nuclear Information System (INIS)

    El-Sawy, S.M.; Ahmed, N.M.; Abd El-Ghaffar, M.A.

    2005-01-01

    Precipitated barium sulphate (Blank fixe) was prepared and evaluated as an extender pigment, making use of the naturally occurring Egyptian barytes ore. X-ray diffraction patterns, transmission electron microscope, thermal gravimetric analysis, color measurements, specific gravity, oil absorption, bulking value, bleed resistance, hydrogen ion concentration, permanence for light and heat and chemical resistance were different methods used for characterization and evaluation of the prepared pigment. Medium oil alkyd resin, melamine-alkyd and epoxy resin were used as different binding media for the application and testing of the prepared pigments as an extender- in some paint formulations, this was done in comparison with a commercial imported blank fixe sample and the Egyptian barytes ore that it was prepared from. It was found that; a white bright fine powder of precipitated barium sulfate could be successfully prepared from the locally abundant Egyptian barytes ore. It has a suitable properties as an extender pigment. Paints pigmented with blank fixe offered favourable rheological and protective properties exceeding that of the imported commercial sample and the ore that was prepared from

  12. X-ray radiometric method of ore quality monitoring during mining

    International Nuclear Information System (INIS)

    Ivanyukovich, G.A.

    1979-01-01

    The method is basically applied for sampling ore deposits, mainly of nonferrous and rare metals. It can be used for determining one, two or three elements in the deposit. In the USSR, the method has so far been used in Far East tin deposits and in the North Caucasus tungsten-molybdenum deposit. It is used for the analysis of boreholes, shaft walls, mined ore and ore material intended for enriching. The instruments used include single-channel gamma spectrometers using scintillation or proportional counters as detectors. Logging instruments include dual-channel spectrometers featuring automatic gain control and data processing devices. The instruments are designed for separating elements with atomic numbers 19 to 88 from mine wall materials and with atomic numbers 26 to 88 in boreholes at concentrations exceeding 0.1% and 0.01% for tin and silver, respectively. The economic benefit is shown of the introduction of the method using the Sadon lead-zinc plant and Khrustalnensk ore treatment plant as examples. (H.S.)

  13. The effect of process water salinity on flotation of copper ore from Lubin mining region (SW Poland

    Directory of Open Access Journals (Sweden)

    Bakalarz Alicja

    2017-01-01

    Full Text Available The process water used for the flotation of sedimentary copper ore in ore concentration plants in KGHM Polska Miedz S.A. were characterized. The process water used in the flotation circuits is heavily saline. It contains between 25 and 45 g/dm3 of soluble components, and the main constituent, in about 75%, is NaCl. Process water used for flotation consists of reclaimed water from the tailing dam and mine water. The effect of process water salinity on the processes of copper flotation from the Lubin mine area was described. The results of laboratory flotation experiments conducted in tap water and in water of different salinity levels were compared. The effect of the salinity of water within specified concentration limits was generally found to be beneficial for upgrading of the examined ore.

  14. Behavior of uranium under conditions of interaction of rocks and ores with subsurface water

    Science.gov (United States)

    Omel'Yanenko, B. I.; Petrov, V. A.; Poluektov, V. V.

    2007-10-01

    The behavior of uranium during interaction of subsurface water with crystalline rocks and uranium ores is considered in connection with the problem of safe underground insulation of spent nuclear fuel (SNF). Since subsurface water interacts with crystalline rocks formed at a high temperature, the mineral composition of these rocks and uranium species therein are thermodynamically unstable. Therefore, reactions directed toward the establishment of equilibrium proceed in the water-rock system. At great depths that are characterized by hindered water exchange, where subsurface water acquires near-neutral and reducing properties, the interaction is extremely sluggish and is expressed in the formation of micro- and nanoparticles of secondary minerals. Under such conditions, the slow diffusion redistribution of uranium with enrichment in absorbed forms relative to all other uranium species is realized as well. The products of secondary alteration of Fe- and Ti-bearing minerals serve as the main sorbents of uranium. The rate of alteration of minerals and conversion of uranium species into absorbed forms is slow, and the results of these processes are insignificant, so that the rocks and uranium species therein may be regarded as unaltered. Under reducing conditions, subsurface water is always saturated with uranium. Whether water interacts with rock or uranium ore, the equilibrium uranium concentration in water is only ≤10-8 mol/l. Uraninite ore under such conditions always remains stable irrespective of its age. The stability conditions of uranium ore are quite suitable for safe insulation of SNF, which consists of 95% uraninite (UO2) and is a confinement matrix for all other radionuclides. The disposal of SNF in massifs of crystalline rocks at depths below 500 m, where reducing conditions are predominant, is a reliable guarantee of high SNF stability. Under oxidizing conditions of the upper hydrodynamic zone, the rate of interaction of rocks with subsurface water

  15. Physicochemical characteristics of aerosol particles generated during the milling of beryllium silicate ores: implications for risk assessment.

    Science.gov (United States)

    Stefaniak, Aleksandr B; Chipera, Steve J; Day, Gregory A; Sabey, Phil; Dickerson, Robert M; Sbarra, Deborah C; Duling, Mathew G; Lawrence, Robert B; Stanton, Marcia L; Scripsick, Ronald C

    2008-01-01

    Inhalation of beryllium dusts generated during milling of ores and cutting of beryl-containing gemstones is associated with development of beryllium sensitization and low prevalence of chronic beryllium disease (CBD). Inhalation of beryllium aerosols generated during primary beryllium production and machining of the metal, alloys, and ceramics are associated with sensitization and high rates of CBD, despite similar airborne beryllium mass concentrations among these industries. Understanding the physicochemical properties of exposure aerosols may help to understand the differential immunopathologic mechanisms of sensitization and CBD and lead to more biologically relevant exposure standards. Properties of aerosols generated during the industrial milling of bertrandite and beryl ores were evaluated. Airborne beryllium mass concentrations among work areas ranged from 0.001 microg/m(3) (beryl ore grinding) to 2.1 microg/m(3) (beryl ore crushing). Respirable mass fractions of airborne beryllium-containing particles were 80% in high-energy input areas (beryl melting, beryl grinding). Particle specific surface area decreased with processing from feedstock ores to drumming final product beryllium hydroxide. Among work areas, beryllium was identified in three crystalline forms: beryl, poorly crystalline beryllium oxide, and beryllium hydroxide. In comparison to aerosols generated by high-CBD risk primary production processes, aerosol particles encountered during milling had similar mass concentrations, generally lower number concentrations and surface area, and contained no identifiable highly crystalline beryllium oxide. One possible explanation for the apparent low prevalence of CBD among workers exposed to beryllium mineral dusts may be that characteristics of the exposure material do not contribute to the development of lung burdens sufficient for progression from sensitization to CBD. In comparison to high-CBD risk exposures where the chemical nature of aerosol

  16. IAEA sends out samples of uranium ore

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1966-06-15

    Full text: Governments and organizations interested in developing uranium resources will be assisted by a new service, now being inaugurated by the Agency's laboratories, for the distribution of reference samples of uranium ores. This is an addition to the service which began at Seibersdorf in January 1962 for the distribution of calibrated radionuclides, and which has met with a steadily increasing demand. * Uranium deposits consisting of ores with a uranium content in the range 0.5 - 0.05 per cent occur in a number of countries, including developing countries and can present considerable analytical difficulties. In 1962 the Agency asked Member States whether they would be interested in receiving reference samples of uranium ores to assist them in checking their methods of chemical analysis. The response encouraged the Agency to proceed. There is a multiplicity of types of uranium ores and, initially, three of the most commonly occurring have been selected - torbernite, uraninite and carnotite. Member States have provided the laboratory with supplies of these three types of ore. In order to determine the uranium content, samples are sent to leading laboratories throughout the world, so as to arrive at the most accurate values possible. This work has proved to be useful to the laboratories themselves ; in searching for reasons for discrepancies between the different collaborating laboratories, they enlarge their own knowledge and improve their methods. The reference samples are sent out in the form of fine powder, and are available to atomic energy commissions, research laboratories or mining companies. The requesting laboratory, having worked out the analytical process best suited to its needs, is then able to check its results by analysing an IAEA reference sample of known uranium content. By the end of 1966, reference samples will be available of the three ores mentioned, and later also of pure uranium oxide and of uranium oxide containing trace impurities, the

  17. Results of cytogenetic examinations of miners exposed to radon in ore mines

    International Nuclear Information System (INIS)

    Beno, M.; Vladar, M.; Nikodemova, D.; Vicanova, M.

    1998-01-01

    In this study the radon air concentrations and clastogenic effects at three ore mines located in central east Slovakia, the gold mine of Hodrusa-Hamre, talcum mine of Hnusta, and iron ore mine in Nizna Slana are compared with the chromosomal aberrations observed in a control group of healthy men which experienced underground work. A random sample of radon concentration measurements in houses was used for control. Significant differences in counts of aberrations of the chromosomal type in lymphocytes of smoker-miners of Nizna Slana as compared with counts of such aberrations in lymphocytes of a control group of similar age were found. A dependence of chromosomal aberration counts from the underground exposure to radon by multiple regression procedures could not be ascertained. The results indicated that confounding of such dependence by smoking might have taken place

  18. In situ production of 36CI in uranium ore: a hydrogeological assessment tool

    International Nuclear Information System (INIS)

    Cornett, R.J.; Cramer, J.; Andrews, H.R.; Chant, L.A.; Davies, W.; Greiner, B.F.; Imahori, Y.; Koslowsky, V.; McKay, J.; Milton, G.M.; Milton, J.C.D.

    1996-01-01

    In situ neutron activation of 35 Cl within the rock and groundwater of geologic deposits that have elevated concentrations of uranium provides a hydrogeological tracer. We determine the production rate and mobility of 36 Cl in the 1.3-billion-year-old Cigar Lake uranium ore deposit. Accelerator mass spectrometry was used to map the Concentrations of 36 Cl in the ore and in the groundwater that were up to 100 times greater than those encountered in unmineralized portions of the host sandstone aquifer. The residence time of this mobile anion in groundwater within the mineralized zone ranged from 14 to 280 kyr. These residence times are consistent with the hydraulic and geochemical data, suggesting significant control of Cl - and groundwater movement by the clay-rich matrix of the mineralized zone. (author)

  19. Prospecting For Magnetite Ore Deposits With A Innovative Sensor's of Unique Fundamentally New Magnetometer.

    Science.gov (United States)

    Emelianenko, T. I.; Tachaytdinov, R. S.; Sarichev, V. F.; Kotov, B. V.; Susoeva, G. N.

    examined the fundamental principles and the potential of all these types of magnetometres, we can see that they cannot solve the problem of local magnetic prospecting. In particular, they cannot determine the coordinates of the ore body prior to drilling. In devising a fundamentally new magnetometre we have used the experience and achievements of radio and magnetic prospecting and electronics. As already noted, the new magnetometre locator has a much higher sensitivity than most modern magnetometres, which approximates the sensitivity of proton-quantum devices. Thanks to its simple design, the new magnetometre has a sharp measurement directivity towards the centre of even quite small commercially processable ore bodies. Instead of the light pumping, magnetic pumping is used in the new magnetometres. The novelty of the approach consisted in concentrating and amplifying the signal from the ore body BOTH at the INPUT and OUTPUT of the sensor. A research team at the Magnitogorsk Iron and Steel Works, Russia (MMK), has developed and patented fundamentally novel magnetometers and methods of quantitative geochemical forecasting of magnetite ore deposits which allow to cut the costs (by as much as 50%) of locating iron ores at all stages of prospecting. The main advantages of the new magnetometers and the geochemical method over the existing ones are as follows: The possibility, before or even without expensive drilling, of determining the coordinates of principal ore bodies both in the horizontal plane and in depth by the new patented magnetometers with elevated sensitivity and sharp measurement directivity as well as of yielding an estimated forecast of the ore reserves; The possibility of an early quantitative estimate of the ore bodies and the ore deposit as a whole based on the results of a SINGLE BOREHOLE in the centre of the location previously determined by the novel magnetometre in contrast to the conventional quantitative evaluation method requiring dozens of boreholes

  20. Bioprocessing of ores: Application to space resources

    Science.gov (United States)

    Johansson, Karl R.

    1992-01-01

    The role of microorganisms in the oxidation and leaching of various ores (especially those of copper, iron, and uranium) is well known. This role is increasingly being applied by the mining, metallurgy, and sewage industries in the bioconcentration of metal ions from natural receiving waters and from waste waters. It is concluded that bioprocessing using bacteria in closed reactors may be a variable option for the recovery of metals from the lunar regolith. Obviously, considerable research must be done to define the process, specify the appropriate bacteria, determine the necessary conditions and limitations, and evaluate the overall feasibility.

  1. Upgrading of boron ores and colemanite flotation

    International Nuclear Information System (INIS)

    Yarar, B.; Mager, J.

    1979-01-01

    Processes applied for the processing and upgrading of sodium and calcium borates in Turkey are described. Details of froth flotation study where a low grade colemanite ore containing calcite and clays as a gangue minerals are given. It has been found that, at the natural pH of a colemanite-containing pulp (pH=9,2) it is possible to float colemanite selectively using dodecyl benzene sulphonate or its combinations with a non-polar reagent or naphthenic acids. (author)

  2. Bacterial leaching of uranium ores - a review

    International Nuclear Information System (INIS)

    Lowson, R.T.

    1975-11-01

    The bacterial leaching of uranium ores involves the bacterially catalysed oxidation of associated pyrite to sulphuric acid and Fe 3+ by autotrophic bacteria and the leaching of the uranium by the resulting acidic, oxidising solution. Industrial application has been limited to Thiobacillus thiooxidans and Thiobacillus ferrooxidans at pH 2 to 3, and examples of these are described. The bacterial catalysis can be improved with nutrients or prevented with poisons. The kinetics of leaching are controlled by the bed depth, particle size, percolation rate, mineralogy and temperature. Current work is aimed at quantitatively defining the parameters controlling the kinetics and extending the method to alkaline conditions with other autotrophic bacteria. (author)

  3. Chromosomal aberrations in ore miners of Slovakia

    International Nuclear Information System (INIS)

    Beno, M.; Vladar, M.; Nikodemova, D.; Vicanova, M.; Durcik, M.

    1998-01-01

    A pilot study was performed in which the incidence of chromosomal aberrations in lymphocytes of miners in ore mines located in Central Slovakia was monitored and related to lifetime underground radon exposure and to lifetime smoking. The conclusions drawn from the results of the study were as follows: the counts of chromosomal aberrations in lymphocytes of miners were significantly higher than in an age matched control group of white-collar staff; the higher counts of chromosomal aberrations could be ascribed to underground exposure of miners and to smoking; a dependence of chromosomal aberration counts on the exposure to radon could not be assessed. (A.K.)

  4. ores - Fauna e flora - Contributo.

    OpenAIRE

    Furtado, Duarte

    1986-01-01

    Situado a mais de 1500 kilómetros da Europa à latitude de Lisboa, o arquipélago dos Açores de origem vulcânica estende-se ao longo dum eixo (SSE-NNW) por 600 kilómetros com nove ilhas repartidas por três grupos distinctos. Povoado nos meados do século XV pelos portugueses, a população actual é de 270.000 habitantes, aproximadamente. Uma origem recente e um vulcanismo muito activo, fazem com que os relevos sejam muito jovens, existindo em cada ilha uma ou mais caldeiras centrais. O clima...

  5. A Multistage Sulphidisation Flotation Procedure for a Low Grade Malachite Copper Ore

    OpenAIRE

    Tebogo P. Phetla; Edison Muzenda

    2010-01-01

    This study was carried out to develop a flotation procedure for an oxide copper ore from a Region in Central Africa for producing an 18% copper concentrate for downstream processing at maximum recovery from a 4% copper feed grade. The copper recoveries achieved from the test work were less than 50% despite changes in reagent conditions (multistage sulphidisation, use of RCA emulsion and mixture, use of AM 2, etc). The poor recoveries were attributed to the mineralogy of t...

  6. Semi-continuous on-line uranium ore analyzer

    International Nuclear Information System (INIS)

    Campbell, P.; Gurdy, E.M.; Hatchowski, L.

    1984-01-01

    The efficient process control of a uranium mill and its associated mining operation requires a nearly continuous knowledge of the uranium concentration in the ore. Generally, the approach is to use laboratory assays of grab samples from the mill feed belt. In some cases, elaborate and expensive systems have been used to ensure random sampling, but even with these systems, mass-balance discrepancies still exist. There is a requirement for an on-line instrument that can give a prompt, accurate analysis of a large portion of the feed stock. The authors have recently evaluated a laboratory system that achieves these goals using neutron activation and delayed neutron counting. The development of the on-line uranium ore analyzer is a consequence of previous work done at the Whiteshell Nuclear Research Establishment (WNRE) (Campbell et al., 1978 and 1981), and is based on the emission of delayed neutrons after the neutron irradiation of fissionable materials. The mechanism of delayed neutron emission has been described (Keepin, 1965), but briefly is as follows. The fission fragments resulting from irradiation are in an excited state. Certain of these delayed fission products, precursors, decay to a more stable state by the emission of a delayed neutron. The delayed neutrons can be divided into six groups with effective half-lives ranging from 0.2-55 sec. It is important to note that more than 50% of the delayed neutrons are emitted within the first 6 sec after irradiation; this has an influence on the design of the analysis instrument

  7. The Application of Artificial Neural Networks to Ore Reserve Estimation at Choghart Iron Ore Deposit

    Directory of Open Access Journals (Sweden)

    Seyyed Ali Nezamolhosseini

    2017-01-01

    Full Text Available Geo-statistical methods for reserve estimation are difficult to use when stationary conditions are not satisfied. Artificial Neural Networks (ANNs provide an alternative to geo-statistical techniques while considerably reducing the processing time required for development and application. In this paper the ANNs was applied to the Choghart iron ore deposit in Yazd province of Iran. Initially, an optimum Multi Layer Perceptron (MLP was constructed to estimate the Fe grade within orebody using the whole ore data of the deposit. Sensitivity analysis was applied for a number of hidden layers and neurons, different types of activation functions and learning rules. Optimal architectures for iron grade estimation were 3-20-10-1. In order to improve the network performance, the deposit was divided into four homogenous zones. Subsequently, all sensitivity analyses were carried out on each zone.  Finally, a different optimum network was trained and Fe was estimated separately for each zone. Comparison of correlation coefficient (R and least mean squared error (MSE showed that the ANNs performed on four homogenous zones were far better than the nets applied to the overall ore body. Therefore, these optimized neural networks were used to estimate the distribution of iron grades and the iron resource in Choghart deposit. As a result of applying ANNs, the tonnage of ore for Choghart deposit is approximately estimated at 135.8 million tones with average grade of Fe at 56.14 percent. Results of reserve estimation using ANNs showed a good agreement with the geo-statistical methods applied to this ore body in another work.

  8. Geology and ore deposits of Johnny M mine, Ambrosia Lake District

    International Nuclear Information System (INIS)

    Falkowski, S.K.

    1980-01-01

    The Johnny M mine is one of very few mines in the Ambrosia Lake district with uranium ore in two members of the Morrison Formation (Jurassic); these members are the Westwater Canyon Sandstone and the Brushy Basin Shale. The Westwater Canyon ore is contained in the two upper sandstone units of the member, and the Brushy Basin ore is contained in the Poison Canyon sandstone (informal usage). The sedimentary features and structures in the Westwater Canyon sandstones indicate that the sediments were deposited by a system of aggrading braided streams, possibly at the distal end of coalescing alluvial fans. The Poison Canyon sandstone was probably the result of deposition in a complex environment of meandering and braided streams. Paleocurrent-direction indicators, such as fossilized-log orientation, foreset azimuths, and the axes of crossbeds and channel scours, suggest that the local palostream flow was to the east and southeast. The uranium mineralization is closely associated with 1) local accumulations of carbonaceous (humate) matter derived from the decay of organic material and 2) paleostream channels preserved in the rocks. The ore elements were derived from the leaching of volcanic air-fall tuffs and ash, which were introduced into the fluvial system during volcanic activity in the western United States. The mobile ore-element ions were reduce and concentrated by humic acids and bacteria present in the fluvial system and ultimately remobilized into the forms present today. The uranium is thus envisioned as forming either essentially on the surface as the sediments were being deposited or at very shallow depth

  9. Sedimentary exhalative nickel-molybdenum ores in south China

    Science.gov (United States)

    Lott, D.A.; Coveney, R.M.; Murowchick, J.B.; Grauch, R.I.

    1999-01-01

    Unique bedded Ni-Mo ores hosted by black shales were discovered in localized paleobasins along the Yangzte platform of southern China in 1971. Textural evidence and radiometric dates imply ore formation during sedimentation of black shales that grade into readily combustible beds, termed stone coals, which contain 10 to 15 percent organic carbon. Studies of 427 fluid inclusions indicate extreme variation in hydrothermal brine salinities that were contained by Proterozoic dolostones underlying the ore zone in Hunan and Guizhou. Variations of fluid inclusion salinities, which range from 0.1 to 21.6 wt percent NaCl equiv, are attributed to differences in the compositions of brines in strata underlying the ore bed, complicated by the presence of seawater and dilute fluids that represent condensates of vapors generated by boiling of mineralizing fluids or Cambrian meteoric water. The complex processes of ore deposition led to scattered homogenization temperatures ranging from 100??to 187??C within the Hunan ore zone and from 65??to 183??C within the Guizhou ore zone. While living organisms probably did not directly accumulate metals in situ in sufficient amounts to explain the unusually high grades of the deposits, sulfur isotope ratios indicate that bacteria, now preserved as abundant microfossils, provided sufficient sulfide for the ores by reduction of seawater sulfate. Such microbiota may have depended on vent fluids and transported organic matter for key nutrients and are consistent with a sedex origin for the ores. Vent fluids interacted with organic remains, including rounded fragments of microbial mats that were likely transported to the site of ore deposition by the action of waves and bottom currents prior to replacement by ore minerals.

  10. Inverse method for determining radon diffusion coefficient and free radon production rate of fragmented uranium ore

    International Nuclear Information System (INIS)

    Ye, Yong-jun; Wang, Li-heng; Ding, De-xin; Zhao, Ya-li; Fan, Nan-bin

    2014-01-01

    The radon diffusion coefficient and the free radon production rate are important parameters for describing radon migration in the fragmented uranium ore. In order to determine the two parameters, the pure diffusion migration equation for radon was firstly established and its analytic solution with the two parameters to be determined was derived. Then, a self manufactured experimental column was used to simulate the pure diffusion of the radon, the improved scintillation cell method was used to measure the pore radon concentrations at different depths of the column loaded with the fragmented uranium ore, and the nonlinear least square algorithm was used to inversely determine the radon diffusion coefficient and the free radon production rate. Finally, the solution with the two inversely determined parameters was used to predict the pore radon concentrations at some depths of the column, and the predicted results were compared with the measured results. The results show that the predicted results are in good agreement with the measured results and the numerical inverse method is applicable to the determination of the radon diffusion coefficient and the free radon production rate for the fragmented uranium ore. - Highlights: • Inverse method for determining two transport parameters of radon is proposed. • A self-made experimental apparatus is used to simulate radon diffusion process. • Sampling volume and position for measuring radon concentration are optimized. • The inverse results of an experimental sample are verified

  11. The fines recovery of the phosphoro-uraniferous ores from Itataia-CE

    International Nuclear Information System (INIS)

    Furtado, J.R.V.

    1985-01-01

    Cyclone desliming previous to flotation is one of the determining factors of the concentration performance of phosfate ores. The physical beneficiation of the phosphoro uraniferous ore of Itataia, carried out in the pilot plant, rejects approximately 10,5% P 2 O 5 and 14% U 3 O 8 contained as ''slimes''. The present investigation was to develop a process to recover the fines through the tecniques of flotation and Seletive Floculation. The low P 2 O 5 content and extremely small size of the ''slimes'', led to a low efficiency in the operation of either flotation. The introduction of a Second disliming step swhed promising results. It is work mentioning that the ore presents siliceous-carbonatic gangue and that the direct flotation of phosphates rejects only the silicate portion. Direct flotation followed by reverse flotation of carbonates led to phosphate concentrates containing 28% P 2 O 5 with recoveries of 60%. The results obtained indicate that the fines treatment may lead to increase of 4,5% in overall recovery without decreasing the grade of the final concentrate. (C.D.G.) [pt

  12. Some developments in the extraction of gold from Witwatersrand ores

    International Nuclear Information System (INIS)

    Laxen, P.A.

    1975-01-01

    The extraction of gold from most ores of the Witwatersrand has been consistently high - approximately 95 per cent - for many years. The present high price of gold has stimulated research and development into potential improvements of the standard procedures. The occurrence of the gold and its association with other minerals is described briefly. The Witwatersrand reefs also contain uranium and pyrite, and some of the improvements to the standard gold-extraction process are associated with the recovery or concentration of one or both of these valuable constituents. For instance, the 'reverse-leach' process, in which acid treatment for the extraction of uranium precedes cyanidation, results in improved gold extraction. Some concentration techniques used on the present residues from cyanidation offer promise in improving the overall gold recoveries. Thucholite is an important carrier of residual gold, and its recovery from some residues by flotation appears to be economically justifiable. Wet high-intensity magnetic separation has given promising results, in the laboratory and on the pilot plant, for the recovery of both uranium and gold from a number of cyanide tailings. The benefits of gravity concentration and of the application of empirical modelling to the gold-extraction process have been demonstrated by a mining group. Some developments in instrumentation for control during cyanidation are discussed briefly [af

  13. Determination of radioactivity levels in phosphate-containing fertilizers, copper and gold ores by direct gamma-ray spectroscopy. U-238, Th-232, K-40, and Ra-226 in fertilizers and ores

    International Nuclear Information System (INIS)

    Constantinescu, B.; Constantin, F.; Dusoiu, N.; Pascovoici, G.

    1996-01-01

    Two particular sources from the natural radiation background which may be encountered in Romanian industry are here presented: the phosphate containing fertilizers and the gold and copper ores, respectively. U-238, Th-232, K-40, and Ra-226 activity levels for several imported phosphorites, superphosphates and also for concentrated Cu and Au indigenous ores are reported. A simple and efficient radioactivity determination procedure based on a large volume NaI(Tl) detector, coupled to a Romanian design portable multichannel analyzer is described. Potential radiological impacts for the specialized workers are also discussed. (author) 1 fig., 4 tabs. 6 refs

  14. Bacterial leaching of pyritic gold ores

    Energy Technology Data Exchange (ETDEWEB)

    Gagliardi, F.M.; Cashion, J.D.; Brown, L.J. [Monash Univ., Clayton, VIC (Australia). Dept. of Physics; Jay, W.H. [Monash Univ., Clayton, VIC (Australia). Chemical Engineering Department

    1996-12-31

    The bacterial oxidation process is well known in nature but has only recently come under investigation as a viable and relatively clean method of gold recovery from ores. However there is currently little information about the process at an atomic scale. It is known that the bacterial attack progresses preferentially along grain boundaries which is precisely where the gold has been deposited from aqueous infiltration. Samples have been obtained from the Wiluna mine in Western Australia consisting of the original ore, 2 pre-treatments, and from six successive bacterial reactors. {sup 57}Fe Moessbauer spectra taken at room temperature show only two quadrupole split doublets which can be ascribed to pyrite, FeS{sub 2}, and arsenopyrite, FeAsS. However, the presence of any superparamagnetic oxide or oxyhydroxide species would be expected to give a spectrum very similar to that of pyrite and would be undetectable in small quantities. At a temperature of 5K, a broad magnetically split sextet is observable with a mean hyperfine field of approximately 50T. This field is characteristic of magnetically ordered ferric iron surrounded by an octahedron of oxygens. The intensity and characteristics of this subspectrum alters through the series and interpretations will be given on the oxidation products of the bacterial leaching

  15. Bacterial leaching of pyritic gold ores

    International Nuclear Information System (INIS)

    Gagliardi, F.M.; Cashion, J.D.; Brown, L.J.; Jay, W.H.

    1996-01-01

    The bacterial oxidation process is well known in nature but has only recently come under investigation as a viable and relatively clean method of gold recovery from ores. However there is currently little information about the process at an atomic scale. It is known that the bacterial attack progresses preferentially along grain boundaries which is precisely where the gold has been deposited from aqueous infiltration. Samples have been obtained from the Wiluna mine in Western Australia consisting of the original ore, 2 pre-treatments, and from six successive bacterial reactors. 57 Fe Moessbauer spectra taken at room temperature show only two quadrupole split doublets which can be ascribed to pyrite, FeS 2 , and arsenopyrite, FeAsS. However, the presence of any superparamagnetic oxide or oxyhydroxide species would be expected to give a spectrum very similar to that of pyrite and would be undetectable in small quantities. At a temperature of 5K, a broad magnetically split sextet is observable with a mean hyperfine field of approximately 50T. This field is characteristic of magnetically ordered ferric iron surrounded by an octahedron of oxygens. The intensity and characteristics of this subspectrum alters through the series and interpretations will be given on the oxidation products of the bacterial leaching

  16. Juuru Mihkli Kiriku Oreli Fond võttis endale uue ülesande / Tauno Kibur

    Index Scriptorium Estoniae

    Kibur, Tauno

    2009-01-01

    Oreli fond on võtnud ülesandeks restaureerida koguduse ajalooline pastoraat. Hoone eskiisi tegi Raivi Juks. Oreli restaureerimist ja tulemust jääb fikseerima Juuru oreli plaat, mille muusikapalad mängis sisse Kristel Aer

  17. 40 CFR 440.20 - Applicability; description of the aluminum ore subcategory.

    Science.gov (United States)

    2010-07-01

    ... subpart B are applicable to discharges from facilities engaged in the mining of bauxite as an aluminum ore. ... (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Aluminum Ore...

  18. Geochemistry and the origin of the Mamouniyeh iron ore-terra rossa deposit, Markazi Province - Iran

    Directory of Open Access Journals (Sweden)

    Marziyeh Mahboubiyan Fard

    2017-11-01

    chert and minor jasper. Some secondary dolomite and calcite, filling the fractures and open spaces are found. Clay minerals are also minor constituents of the ore. The remaining fossils of green-blue algae indicate the conditions of iron deposition and effective biological processes in oxidizing Fe+2 and creation of new oxide minerals in a sedimentary basin. XRD studies show that tetraferriannite, hisingerite, barite, dolomite and calcite are present in addition to dominant hematite and quartz minerals. Hisingerite is formed in sedimentary iron deposits during hydrothermal alteration (Whelan and Goldich., 1961. Tetraferriannite occurs in low grade iron formations (Miyano, 1982. Structurally, the mineralization is controlled by a tectonic zone in which abundant breccias and faults are well found. The amount of Fe2O3 ranges between 11.62% and 65.73%, with an average value of 31% Fe2O3. The amounts of Cr (3-95 ppm and Zr (<5-29 ppm are low; while, the deposit contains a moderate amount of V (26-189 ppm and high concentrations of Zn (28-218 ppm, Sr (66-1462 ppm and Ba (62-5511 ppm. The concentration of REEs shows that total amount of these elements is variable and it falls in the range of 2.34-12.74 ppm. The amount of LREEs falls in the range of 1.66-11.94 ppm and that of HREEs falls in 0.21-2.22 ppm. These values clearly indicate the enrichment of ore in LREEs relative to HREEs. The Eu anomaly (Eu/Eu* lies in the range of 1.32-10.2, indicating positive Eu anomalies. The Ce anomalies (Ce/Ce* fall in the range of 0.076-0.52, suggesting negative anomaly. Discussion The low concentration of Cr and Zr, and high values of V, Zn and Sr in the ore suggest that mineralization is related to submarine volcanic activities. Geochemical data, including chondrite-normalized REE patterns, indicate that seafloor hydrothermal fluids are the most probable source for mineralizing solutions. The ∑(Cu+Co+Ni vs. ∑REE diagram also indicates the role of deep sea hydrothermal fluids in the

  19. Influence of particle size and mineral phase in the analysis of iron ore slurries by Laser-Induced Breakdown Spectroscopy

    International Nuclear Information System (INIS)

    Michaud, Daniel; Leclerc, Remi; Proulx, Eric

    2007-01-01

    Laser-Induced Breakdown Spectroscopy (LIBS) was applied to the analysis of iron ore concentrates. The objective was to determine the influence of particle size and mineral phase on the LIBS signal. The LIBS spectra of hematite and magnetite ore concentrates were qualitatively indistinguishable from each other but magnetite yielded systematically less than hematite. This behavior could be set into an empirical equation to correct the iron peak intensities according to the level of magnetite in the analyzed sample. Similarly, an increase of the LIBS signal was observed as the particle size of the ore samples decreased. Again, an equation could be written down to correct the intensity of either iron or silicon in response to a variation of the average particle size of the ore concentrate. Using these corrections, proper response of the silicon signal against the concentration of silica in the samples was restored. The observed dependence of the strength of the iron signal upon the mineral phase is attributed to oxidation of magnetite into hematite

  20. Developments of uranium and gold ores heap leaching technologies

    International Nuclear Information System (INIS)

    Tian Yuan; Guan Zibin; Gao Renxi

    1998-01-01

    The author reviews developments in heap leaching of uranium and gold ores at home and abroad, summarises condition of application. The author also presents problems having to be studied and settled urgently in heap leaching of uranium and gold ores in China

  1. Waste monitoring of the uranium ore processing activities in Romania

    International Nuclear Information System (INIS)

    Nica, L.

    2002-01-01

    The uranium ore processing activities at the Feldioara site produce a range of liquid and solid waste that are monitored. Liquids are treated through decantation, pH correction and uranium precipitation before their release into the environment. The solid waste is gathered into ore specific area and are covered regularly with clay materials. (author)

  2. Arsenic bioleaching in medical realgar ore and arsenicbearing ...

    African Journals Online (AJOL)

    However, the maximum arsenic leaching ratio from realgar in the presence of mixed unadapted strains was only 12.4 %. Besides, maximum arsenic leaching ratios from arsenic-bearing refractory gold ore by mixed adapted strains or unadapted strains were 45.0 and 22.9 %, respectively. Oxidation of these two ores by ...

  3. Treatment of bastnaesite ore from Vietnamese Socialist Republic

    International Nuclear Information System (INIS)

    Formanek, J.; Jerabek, J.; Jancarek, J.

    1987-01-01

    From the Vietnamese deposit at Nam Nam Xe Czechoslovakia imported several hundred tons of ore. Several methods of ore dressing were used: gravitational, preconcentration in electromagnetic field, magnetic separation, high-intesity electromagnetic separation. Flotation evidently was the best dressing method tried. The results are presented of testing using different flotation agents. (E.S.)

  4. Some aspects of the processing development for uranium ores treatment

    International Nuclear Information System (INIS)

    Bruno, J.B.

    1982-01-01

    It is discussed the methodology adopted by NUCLEBRAS to the processing development for uranium ores treatment. The used methodology has the following steps: exploratories studies, preliminaries stiudies and optimization studies. The studies include physical and chemical contained in the solution. As examples are cited the uranium ores treatment in Lagoa Real and Itataia. (A.B.) [pt

  5. Ore reserve estimation of uranium deposit Zirovski vrh

    International Nuclear Information System (INIS)

    Lukacs, E.

    1979-01-01

    The uranium ore deposit Zirovski vrh is in the Permian sediments of Northwest Yugoslavia. Lenticular bodies occur at several stratiform levels in grey, medium-grained sandstone. The ore deposit will be mined entirely by underground methods. It is possible to define three stages of deposit evaluation requiring different densities of exploration effort: preliminary evaluation of in situ ore reserves; evaluation of mineable ore reserves; evaluation of production capability and mine planning. The drilling density increases markedly with each succeeding stage. The optimal drilling density for all three stages of evaluation should be determined, but there is some concern that too close spaced drilling would considerably increase the exploration costs without a corresponding increase in effectiveness. On the other hand, too sparsely spaced drilling may result in some difficulties in following the ore in mining. The paper treats the problem of the density of drilling for evaluation of mineable ore reserves compared to that required for mine planning and mine production capability. The purpose of investigation of mineral raw materials is to define economic deposits (ore bodies). To evaluate the deposit economically an accurate reserve estimate is required. If it is accordingly established that such an estimate is within the degree of admissible error, the purpose of the exploration is satisfied. However, the problem as to whether the drilling grid is sufficiently dense remains, because the majority of estimates of ore reserves do not provide a measure of the reliability of the estimate. (author)

  6. Overview of the long distance iron ore slurry pipeline from Anglo Ferrous Brazil

    Energy Technology Data Exchange (ETDEWEB)

    Silva, Adarlan M.; Passos, Aline C.; Santos, Daniel; Orban, Eduardo M.; Lisboa, Helder D.; Goncalves, Nilton; Guimaraes, Robson C. [Anglo Ferrous Brazil, Rio de Janeiro, RJ (Brazil)

    2009-07-01

    The objective of this paper is to present an overview of the long distance iron ore slurry pipeline from Anglo Ferrous Brazil. Anglo Ferrous Brazil is a company of Anglo American plc that is one of the world's largest mining and natural resource company. Minas-Rio is a world class iron ore project which has been developed in Brazil aiming to produce 26.6 million tons per year of concentrate. The mine, concentrator and pump station 1 will be located in Conceicao do Mato Dentro, Minas Gerais state, and the terminal station will be located at Acu Port in Sao Joao da Barra, Rio de Janeiro state. The long distance iron ore slurry pipeline will be one of major differentials of Minas-Rio Project and its useful life was initially estimated in 20 years. The slurry pipeline has a total length of 525 kilometers and will be constructed from predominately 26 inches external diameter API 5L X70 pipes. From kilometer 314 to kilometer 480, 24 inches pipe will be installed to prevent slack flow downstream pump station 2. The pump station 1 is designed to provide the hydraulic head necessary to transport the concentrate iron ore slurry with 8 positive displacement pumps to pump station 2. The pump station 2, located 240 kilometers downstream pump station 1, is designed to operate with 10 positive displacement pumps. The valve station will be located at kilometer 347 and will be used to break the static head between pump station 2 and the terminal station during a slurry pipeline shutdown. (author)

  7. Lung cancer and inhaled uranium ore dust in rats

    International Nuclear Information System (INIS)

    Mitchel, R.E.J.; Jackson, J.S.

    1997-01-01

    Using a nose only inhalation system, 187 nine week old male Sprague-Dawley rats were exposed to two different concentrations of natural uranium ore dust aerosol (44% U) without significant radon content. Inhalation exposures averaged about 4.2 h/day, 5 days/week for 65 weeks at which point lung uranium burdens in the two groups averaged 0.9 and 1.9 mg/g dry weight. Animals (63) exposed to the air stream without dust served as controls. After inhalation exposure ceased, the rats were allowed to live for their natural lifetime, a maximum of about 900 days after the start of dust inhalation. Lung uranium burdens were measured at the time of death of each animal. Lung burdens were found to decline exponentially after dust inhalation ceased, and the rate of decline was independent of the initial lung burden. All lungs were examined at necropsy and histologically for lung tumors. Lung tumors of lung origin were observed in both exposed groups and in the control group. The frequency of primary malignant lung tumors was 0.016, 0.175 and 0.328 and primary non-malignant lung tumors 0.016, 0.135 and 0.131 in the control low and high aerosol exposed groups respectively. Absorbed dose to the lung was calculated for each animal in the study. The average maximum doses for all the animals exposed to the low or high concentration of dust aerosol were 0.87 Gy and 1.64 Gy respectively. The average risk of malignant lung tumors from inhaled natural uranium ore dust was therefore about 0.20 tumors/animal/Gy. For animals with lung tumors, the average doses were 0.98 and 1.90 in the exposed groups. In both exposed groups, the frequency of primary malignant or non-malignant lung tumors was significantly greater than in the control group (p < 0.02) and the frequency of primary malignant lung tumors in the two exposed group were significantly different from each other (p = 0.05). The frequency of primary lung tumors (malignant and non-malignant) was calculated as a function of dose

  8. Long-Term Planning for Open Pits for Mining Sulphide-Oxide Ores in Order to Achieve Maximum Profit

    Science.gov (United States)

    Kržanović, Daniel; Conić, Vesna; Stevanović, Dejan; Kolonja, Božo; Vaduvesković, Jovan

    2017-12-01

    Profitable exploitation of mineralised material from the earth's crust is a complex and difficult task that depends on a comprehensive planning process. Answering the question of how to plan production depends on the geometry of the deposit, as well as the concentration, distribution, and type of minerals in it. The complex nature of mineral deposits largely determines the method of exploitation and profitability of mining operations. In addition to unit operating costs and metal prices, the optimal recovery of and achievement of maximum profit from deposits of sulphide-oxide ores also depend, to a significant extent, on the level of technological recovery achieved in the ore processing procedure. Therefore, in defining a long-term development strategy for open pits, special attention must be paid to the selection of an optimal procedure for ore processing in order to achieve the main objective: maximising the Net Present Value (NPV). The effect of using two different processes, flotation processing and hydrometallurgical methods (bioleaching acid leaching), on determining the ultimate pit is shown in the case of the Kraku Bugaresku-Cementacija sulphide-oxide ore deposit in eastern Serbia. Analysis shows that the application of hydrometallurgical methods of processing sulphide-oxide ore achieved an increase in NPV of 20.42%.

  9. Practice of the counter-current trickle leaching of uranium ore by refreshed liquor of bacterial oxidation

    International Nuclear Information System (INIS)

    Chen Shian; Huang Xiangfu; Fan Baotuan

    1995-01-01

    The uranium ore of the Mine No. 753 is a high-silicate type primary one, in which the tetravalent uranium accounts for 85%, and the uranium grade is in the range of 0.36% to 0.442%. To reduce the engineering investment and the operating cost a four-stage counter-current trickle leaching pilot-plant test was carried out with the leaching time 50 days and acid consumption 38 kg per ton of ore, and the recovery of more than 95% was obtained. Using the counter-current trickle leaching mode and controlling the limit concentration of the harmful matters in the bacterial leaching liquor, the latter can be effectively oxidized by the synchronical regeneration. A trickle leaching comparative test of 25 ton ore single heap also gave a good result of more than 95% in extraction rate, and 30% acid consumption was saved and the 2.0% pyrolusite (containing MnO 2 40%) was eliminated. This process is feasible in technology and worth-while in economy for treating the uranium ore of Mine No. 753, and provides a new method of uranium ore trickle leaching

  10. Geochemical study of the insoluble organic material (kerogen) in the Oklo uranium ore and the associated Francevillian schists

    International Nuclear Information System (INIS)

    Vandenbroucke, M.; Rouzaud, J.N.; Oberlin, A.

    1978-01-01

    The purpose of this study was to describe the organic material associated with uranium ore and ore transformations undergone by it, in terms of the following problems: (1) In the natural reactor zones, evolution of the organic material in the core and as a function of the distance away from it; (2) Comparison of organic materials from a rich and a poor ore; (3) Intercomparison of organic materials in the dispersed and concentrated state; (4) Comparison of organic materials in the uranium ore zones and in the adjacent non-mineralized Francevillian. The organic material from the reactor core could not be isolated by the normal techniques of treatment with acid. It is found in other cases that the organic material is oxidized in the uranium-bearing sediments and that the nearer to the reaction zone, the greater the oxidation, irrespective of the state of dispersion of the organic material in the rock. The uranium content does not affect this phenomenon, which is attributed to the action of the water raised to a high temperature in the vicinity of the reaction zones. On the basis of the present distribution of organic material and uranium the authors suggest a pattern for the formation of the deposit that would take into account localization of the ore in the sandstones and the part played by organic material in the accumulation process. (author)

  11. Study On Beneficiation Technology Of Dong Pao Rare-Earth-Barite-Fluorite With Two Product Plans About Content And Recovery Of Rare-Earth Fine Ores

    International Nuclear Information System (INIS)

    Duong Van Su; Truong Thi Ai; Bui Ba Duy; Bui Thi Bay; Nguyen Hong Ha; Le Thi Hong Ha; Doan Thi Mo; Doan Dac Ban; Nguyen Hoang Son

    2014-01-01

    The ore sample used in the research was taken from the F3 ore bodies and the sample of the F7, F9 and F16 ore bodies which contain the average of 5.98% TR 2 O 3 ; they are multi-metals ore which is difficult to enrich, highly weather with very complex ingredients. The process of the experiment is the ore is crushed, ground, screened and classified reasonably to -0.1 mm and divided into 3 particle size with the following technique: (1) -0.020 mm is primary sludge and the rare-earth fine ore; (2) 0.075-1 mm is gotten through the sludge concentrating table with the output is the 2 parts: the heavy part which is dried magnetic separator with high magnetism to get the rare-earth fine ore and the light one; (3) Light minerals, non-magnetic and ferromagnetic minerals group are ground together to 85% of them get size within -0.075 mm then mix it with 0.020-0.075 mm group. Using flotation separator, get barite-rare earth mixture and fluorite. After that, we separate this mixture by secondary flotation and get refined rare earth, barite and fluorite mineral. The result of the theme: (1) product plan A-rare-earth fine ore has TR 2 O 3 content archive 42.07% with recovery is 69.70%; (2) product plan B-rare-earth fine ore has TR 2 O 3 content archive 29.64% with recovery is 80.01%. (author)

  12. Radiation risk, medical surveillance programme and radiation protection in mining and milling of uranium ores

    International Nuclear Information System (INIS)

    Rakshit, A.K.

    1991-01-01

    Mining and milling of uranium ores comprise multiple operations such as developement, drilling, blasting, handling, crushing, grinding, leaching of the ore and concentration, drying, packaging and storing of the concentrate product. Apart from the hazards of any metal mining and milling operations due to dust, noise, chemicals, accidents etc there are radiation risks also resulting from exposure to airborne radioactivity and external radiation. The inhalation risk is of more concern in underground mines than in open pit mines. The objective of a Medical Surveillance Programme (an occupational Health Programme) is to ensure a healthy work force. It should ultimately lead to health maintenance and improvement, less absenteeism increased productivity and the achievement of worker and corporate goals. The programme includes prevention, acute care, counselling and rehabilitation. Radiological workers require special monitoring for their work-related radiation exposure effect by film monitoring service, whole body counting and bioassay. Radiation protection in the mining and milling of Uranium ores include the use of personal protective equipment, work station protection, personal hygiene and house keeping. (author). 15 refs

  13. Characterization and Separation Studies of a Fine Sedimentary Phosphate Ore Slime

    Directory of Open Access Journals (Sweden)

    Xin Liu

    2017-06-01

    Full Text Available Detailed characterization and recovery of apatite from a sedimentary phosphate ore slime of a gravity plant of Yichang, China, were investigated. The phosphate ore slime consisted mainly of apatite, quartz, dolomite, and clay. To start with, the ore slime was characterized in sufficient detail to reveal that it is extremely fine in distribution with a d50 of 65 μm. Other different characterizations, such as apatite grain size distribution, apatite liberation, particle density distribution, and theoretical grade recovery, were also analyzed by mineral liberation analyser (MLA. Based on the results, a new gravity-flotation process, which was comprised of spiral gravity and reverse flotation, was proposed to process the slime. In the new process, the apatite was firstly recovered by two-stage spiral gravity, avoiding direct flotation. The gravity concentrate was the feed for the reverse flotation. A phosphate concentrate of 30.51% P2O5 with a P2O5 recovery of 89.00% can be produced from the slime analyzing 24.25% P2O5. Compared to the conventional direct-reverse flotation process, it was found that the reagent cost of the new gravity-flotation process was lower a quarter than that of the direct-reverse flotation flowsheet.

  14. Ambient Temperature Flotation of Sedimentary Phosphate Ore Using Cottonseed Oil as a Collector

    Directory of Open Access Journals (Sweden)

    Yaoyang Ruan

    2017-04-01

    Full Text Available The mid-low grade sedimentary phosphate ore, abundant in silicate and carbonate gangue minerals, exhibits a poor processability. It is conventionally enriched using high temperature flotation to remove silicate gangues with fatty acid as a collector. Cottonseed oil has been proved to be an efficient collector for achieving ambient temperature flotation of the sedimentary phosphate ore used in this study. Flotation kinetics was investigated to ascertain the excellent collecting performance of cottonseed oil, as compared with oleic acid, and the phosphate flotation fitted well with the first-order flotation model. Based on the analysis of flotation reagent effect on the direct flotation process using the response surface methodology (RSM, a closed circuit of direct-reverse flotation for stepwise removing silicate and carbonate gangues from the sedimentary phosphate ore was established. Consequently, a required high quality of phosphate concentrate containing 30.16% P2O5 was obtained, with a recovery of 90.90%. Scanning electron microscopy (SEM and X-ray diffraction analysis (XRD of the flotation products confirmed that the majority of silicate and carbonate gangues were effectively removed from the concentrate products.

  15. A 197Au and 57Fe Moessbauer study of the roasting of refractory gold ores

    International Nuclear Information System (INIS)

    Wagner, F.E.; Marion, P.

    1989-01-01

    The transformation of chemically bound gold into metallic gold during industrial scale roasting of an arsenical gold ore concentrate from the Fairview Mine, Eastern Transvaal, has been studied quantitatively by 197 Au Moessbauer spectroscopy. The iron compounds in the concentrate, mainly FeAsS and FeS 2 , and their transformations during roasting have been studied by 57 Fe Moessbauer spectroscopy. The bound gold is found to convert into the metal in parallel to the decomposition of FeAsS and the increase in cyanide leachability. This shows that the refractory character of the ore is caused by the chemical bonding of the gold rather than by the physical inclusion of small, discrete metallic particles in the matrix of FeAsS or FeS 2 . The ratio of the f-factors of gold bound in the FeAsS component of a refractory ore and of metallic gold was determined to be f(Au:FeAsS)/f(Au)=1.48 ± 0.09. (orig.)

  16. Purification of trona ores by conditioning with an oil-in-water emulsion

    Science.gov (United States)

    Miller, J. D.; Wang, Xuming; Li, Minhua

    2009-04-14

    The present invention is a trona concentrate and a process for floating gangue material from trona ore that comprises forming an emulsion, conditioning the trona ore at a high solids content in a saturated trona suspension, and then floating and removing the gangue material. The process for separating trona from gangue materials in trona ore can include emulsifying an oil in an aqueous solution to form an oil-in-water emulsion. A saturated trona suspension having a high solids content can also be formed having trona of a desired particle size. The undissolved trona in the saturated suspension can be conditioned by mixing the saturated suspension and the oil-in-water emulsion to form a conditioning solid suspension of trona and gangue material. A gas can be injected through the conditioning solid suspension to float the gangue material. Thus, the floated gangue material can be readily separated from the trona to form a purified trona concentrate without requirements of additional heat or other expensive processing steps.

  17. Optimization of flotation variables for the recovery of hematite particles from BHQ ore

    Science.gov (United States)

    Rath, Swagat S.; Sahoo, Hrushikesh; Das, B.

    2013-07-01

    The technology for beneficiation of banded iron ores containing low iron value is a challenging task due to increasing demand of quality iron ore in India. A flotation process has been developed to treat one such ore, namely banded hematite quartzite (BHQ) containing 41.8wt% Fe and 41.5wt% SiO2, by using oleic acid, methyl isobutyl carbinol (MIBC), and sodium silicate as the collector, frother, and dispersant, respectively. The relative effects of these variables have been evaluated in half-normal plots and Pareto charts using central composite rotatable design. A quadratic response model has been developed for both Fe grade and recovery and optimized within the experimental range. The optimum reagent dosages are found to be as follows: collector concentration of 243.58 g/t, dispersant concentration of 195.67 g/t, pH 8.69, and conditioning time of 4.8 min to achieve the maximum Fe grade of 64.25% with 67.33% recovery. The predictions of the model with regard to iron grade and recovery are in good agreement with the experimental results.

  18. Radiation protection of workers in mining and processing of uranium ore

    International Nuclear Information System (INIS)

    Khan, A.H.; Sahoo, S.K; Puranik, V.D.

    2003-01-01

    Low grade of uranium ore mined from three underground mines is processed in a mill at Jaduguda in eastern India to recover uranium concentrate in the form of yellow cake. Radiation protection of workers is given due importance at all stages of these operations. Dedicated Health Physics Units and Environmental Survey Laboratories established at the site regularly carry out in-plant and environmental surveillance to keep radiation exposure of workers and the members of public within the limits prescribed by the regulatory body. The limits set by the national regulatory body based on the international standards recommended by the ICRP and the IAEA are followed. In the uranium mines, external gamma radiation, radon and airborne activity due to radioactive dust are monitored. Similarly, in the uranium ore processing mill, gamma radiation and airborne radioactivity due to long-lived α-emitters are monitored. Personal dosimeters are also issued to workers. The total radiation exposure of workers from external and internal sources is evaluated from the area and personal monitoring data. It has been observed that the average radiation dose to workers has been below 10 mSvy -1 and all exposures are well below 20 mSvy -1 at all stages of operations. Adequate ventilation is provided during mining and ore processing operations to keep the concentrations of airborne radioactivity well below the derived limits. Workers use personal protective appliances, where necessary, as a supplementary means of control. The monitoring methodologies, results and control measures are presented in the paper. (author)

  19. Migration of radium from the thorium ore deposit of Morro do Ferro, Pocos de Caldas, Brazil

    International Nuclear Information System (INIS)

    Campos, M.J.; Penna-Franca, E.; Lobao, N.; Trindade, H.; Sachett, I.

    1986-01-01

    A large thorium ore deposit is located in Morro de Ferro, a hill in the Pocos de Caldas Plateau, Minas Gerais, Brazil, which contains an estimated 30 000 t of Th and 100 t of U in a highly weathered matrix exposed to erosion and leaching. 228 Ra and 226 Ra were analyzed in surface waters collected at various points in the drainage basin and in groundwaters from wells drilled through and around the ore body. The concentrations in groundwater demonstrated that radium is markedly leached by rainwater percolating through the ore body. In its transit underground, radium is removed from groundwater by sorption on soil particles and this natural process greatly reduces the radium discharged to the environment. In dry weather, the concentration of dissolved 228 Ra in the main stream draining the Morro do Ferro is 7.0+-1.1 mBq litre -1 and in a control stream 1.6+-0.3 mBq litre -1 . The estimated 228 Ra mobilization rate by solubilization is of the order of 10 -7 y -1 . (author)

  20. Determination of Au, Pt, Pd in gold ore mineral raw materials by stripping voltammetry

    Directory of Open Access Journals (Sweden)

    Kolpakova N.A.

    2016-01-01

    Full Text Available The paper considers the possibilities of use of the method of stripping voltammetry for finding platinum metals in mineral gold and ore raw material. A review of new options of electro-concentration of platinum metals on the surface of graphite electrode with the following sediment electro-oxidation and receipt of an analytical signal is presented: platinum finding was carried out by picks of selective electro-oxidation of iridium from intermetallic compound with platinum; gold finding was carried out by picks of gold electro-oxidation on the surface of graphite electrode modified by bismuth; palladium finding was performed by picks of palladium electro-oxidation on the surface of graphite electrode. 1M HCL solution was selected as a supporting electrolyte. Gold and hydrogen elimination on the process of palladium electro-oxidation was performed by means of UV irradiation of solution in the process of electro-concentration of palladium sediment. Gold, platinum and palladium determination was carried out in mineral gold and ore raw material of Verkhneamylskiy gold and ore district.

  1. Discussion on uranium ore-formation age in Xiazhuang ore-field, northern Guangdong

    International Nuclear Information System (INIS)

    Wu Lieqin; Tan Zhengzhong; Liu Ruzhou; Huang Guolong

    2003-01-01

    There exist two genetic types of granite-type uranium deposits, i.e. the early-stage one, and the late-stage one. The early-stage uranium deposits are characterized by ore-formation ages of 122-138 Ma, and are high-grade uranium deposits of postmagmatic hydrothermal origin. The late-stage uranium deposits have ore-formation ages of 54-96 Ma. They mostly are low-grade uranium deposits, and of hydrothermal-regeneration origin with the uranium source derived from the mobilization of consolidated rocks. The early-stage uranium deposits should be the main target of further prospecting for high-grade uranium deposits in the region

  2. Summary of the mineralogy of the Colorado Plateau uranium ores

    Science.gov (United States)

    Weeks, Alice D.; Coleman, Robert Griffin; Thompson, Mary E.

    1956-01-01

    In the Colorado Plateau uranium has been produced chiefly from very shallow mines in carnotite ores (oxidized vanadiferous uranium ores) until recent deeper mining penetrated black unoxidized ores in water-saturated rocks and extensive exploration has discovered many deposits of low to nonvanadiferous ores. The uranium ores include a wide range from highly vanadiferous and from as much as one percent to a trace of copper, and contain a small amount of iron and traces of lead, zinc, molybdenum, cobalt, nickel, silver, manganese, and other metals. Recent investigation indicates that the carnotite ores have been derived by progressive oxidation of primary (unoxidized) black ores that contain low-valent uranium and vanadium oxides and silicates. The uranium minerals, uraninite and coffinite, are associated with coalified wood or other carbonaceous material. The vanadium minerals, chiefly montroseite, roscoelite, and other vanadium silicates, occur in the interstices of the sandstone and in siltstone and clay pellets as well as associated with fossil wood. Calcite, dolomite, barite and minor amounts of sulfides, arsenides, and selenides occur in the unoxidized ore. Partially oxidized vanadiferous ore is blue black, purplish brown, or greenish black in contrast to the black or dark gray unoxidized ore. Vanadium combines with uranium to form rauvite. The excess vanadium is present in corvusite, fernandinite, melanovanadite and many other quadrivalent and quinquevalent vanadium minerals as well as in vanadium silicates. Pyrite and part or all of the calcite are replaced by iron oxides and gypsum. In oxidized vanadiferous uranium ores the uranium is fixed in the relatively insoluble minerals carnotite and tyuyamunite, and the excess vanadium commonly combines with one or more of the following: calcium, sodium, potassium, magnesium, aluminum, iron, copper, manganese, or barium, or rarely it forms the hydrated pentoxide. The relatively stable vanadium silicates are little

  3. Study on the pre-treatment of oxidized zinc ore prior to flotation

    Science.gov (United States)

    He, Dong-sheng; Chen, Yun; Xiang, Ping; Yu, Zheng-jun; Potgieter, J. H.

    2018-02-01

    The pre-treatment of zinc oxide bearing ores with high slime content is important to ensure that resources are utilized optimally. This paper reports an improved process using hydrocyclone de-sliming, dispersion reagents, and magnetic removal of iron minerals for the pre-treatment of zinc oxide ore with a high slime and iron content, and the benefits compared to traditional technologies are shown. In addition, this paper investigates the damage related to fine slime and iron during zinc oxide flotation, the necessity of using hydrocyclone de-sliming together with dispersion reagents to alleviate the influence of slime, and interactions among hydrocyclone de-sliming, reagent dispersion, and magnetic iron removal. Results show that under optimized operating conditions the entire beneficiation technology results in a flotation concentrate with a Zn grade of 34.66% and a recovery of 73.41%.

  4. Flotation of zinc and lead oxide minerals from Olkusz region calamine ores

    Directory of Open Access Journals (Sweden)

    Cichy Krystian

    2016-01-01

    Full Text Available The paper presents chemical and mineralogical characteristics of calamine ore from the Pomorzany mine. A flowsheet for recovery of sulphide minerals of zinc and lead in the form of the Zn-Pb bulk concentrate was presented. In the following part, preparation of the feed for flotation of Zn-Pb oxide minerals and optimal conditions for separation from it iron sulphide minerals, represented by marcasite, were determined. In the final section the results of flotation of Zn-Pb oxide minerals with anionic collector AM2 belonging to the hydroxyamide group of collectors and a cationic collector in the form of a coconut amine, being a mixture of primary aliphatic amines, were presented. Basing on the obtained results, a technological flowsheet for the recovery of Zn-Pb sulphide and oxide minerals from the calamine ore of the Pomorzany mine was presented.

  5. Tantalum and niobium carbides obtention by carbothermic reduction of columbotantalite ores

    International Nuclear Information System (INIS)

    Gordo, E.; Garcia-Carcedo, F.; Torralba, J.M.

    1998-01-01

    Tantalum and niobium carbides are characterized by its high hardness and chemical corrosion resistance. Both carbides, but mainly TaC, are used in hard metals (sintered carbides), together with their carbides, to manufacture cutting tools and dies in special machining applications involving mechanical shock at high temperature. Its use as reinforcement of wear resistant materials through powder metallurgy techniques are being investigated. However, the use of TaC is usually limited because of its high cost. Therefore tantalum carbide with niobium content, which is cheaper, is used. In this work the obtention of complex tantalum and niobium carbides from a Spanish columbotantalite ore is studied through relatively cheap and simple process as it is carbothermic reduction. Concentration of the ore, its reduction and the characterization of products are described. (Author) 11 refs

  6. Soil Contamination at the Historical Zn-Pb Ore Mining Sites (Southern Poland

    Directory of Open Access Journals (Sweden)

    Aleksander-Kwaterczak U.

    2013-04-01

    Full Text Available Results of metals analyses in soil profiles sampled at two 18/19th century mine shafts of the Trzebinia lead-zinc ore mining region in southern Poland are presented. Waste dump sites located at these shafts exhibit initial pedogenesis with clear differences in zinc and cadmium content between soil horizons which changes in depth across each of the investigated dump. The highest metal concentrations occur in horizons containing excavated ore-bearing Triassic dolomites, soils buried beneath are less polluted whereas, initial A0 soil horizons are virtually unpolluted. Relatively low downward metal migration in profiles to the horizons underlying the dumps is related to alkaline pH of soils. Migration appear to be important in the more acidic soils of outer zones in the two dump sites overgrown either with coniferous and deciduous trees.

  7. TEXTURAL DESCRIPTORS FOR MULTIPHASIC ORE PARTICLES

    Directory of Open Access Journals (Sweden)

    Laura Pérez-Barnuevo

    2012-11-01

    Full Text Available Monitoring of mineral processing circuits by means of particle liberation analysis through quantitative image analysis has become a routine technique within the last decades. Usually, liberation indices are computed as weight proportions, which is not informative enough when complex texture ores are treated by flotation. In these cases, liberation has to be computed as phase surface exposed to reactants, and textural relationships between minerals have to be characterized to determine the possibility of increasing exposure. In this paper, some indices to achieve a complete texture characterization have been developed in terms of 2D phase contact and mineral surfaces exposure. Indices suggested by other authors are also compared. The response of this set of parameters against textural changes has been explored on simple synthetic textures ranging from single to multiple inclusions and single to multiple veins and their ability to discriminate between different textural features is analyzed over real mineral particles with known internal structure.

  8. Alternative leaching processes for uranium ores

    International Nuclear Information System (INIS)

    Ring, R.J.

    1979-01-01

    Laboratory studies have been carried out to compare the extraction of uranium from Australian ores by conventional leaching in sulphuric acid with that obtained using hydrochloric acid and acidified ferric sulphate solutions. Leaching with hydrochloric acid achieved higher extractions of radium-226 but the extraction of uranium was reduced considerably. The use of acidified ferric sulphate solution reduced acid consumption by 20-40% without any detrimental effect on uranium extraction. The ferric ion, which is reduced during leaching, can be reoxidized and recycled after the addition of acid makeup. Hydrogen peroxide was found to be an effective oxidant in conventional sulphuric acid leaching. It is more expensive than alternative oxidants, but it is non-polluting, lesser quantities are required and acid consumption is reduced

  9. Ore minerals textural characterization by hyperspectral imaging

    Science.gov (United States)

    Bonifazi, Giuseppe; Picone, Nicoletta; Serranti, Silvia

    2013-02-01

    The utilization of hyperspectral detection devices, for natural resources mapping/exploitation through remote sensing techniques, dates back to the early 1970s. From the first devices utilizing a one-dimensional profile spectrometer, HyperSpectral Imaging (HSI) devices have been developed. Thus, from specific-customized devices, originally developed by Governmental Agencies (e.g. NASA, specialized research labs, etc.), a lot of HSI based equipment are today available at commercial level. Parallel to this huge increase of hyperspectral systems development/manufacturing, addressed to airborne application, a strong increase also occurred in developing HSI based devices for "ground" utilization that is sensing units able to play inside a laboratory, a processing plant and/or in an open field. Thanks to this diffusion more and more applications have been developed and tested in this last years also in the materials sectors. Such an approach, when successful, is quite challenging being usually reliable, robust and characterised by lower costs if compared with those usually associated to commonly applied analytical off- and/or on-line analytical approaches. In this paper such an approach is presented with reference to ore minerals characterization. According to the different phases and stages of ore minerals and products characterization, and starting from the analyses of the detected hyperspectral firms, it is possible to derive useful information about mineral flow stream properties and their physical-chemical attributes. This last aspect can be utilized to define innovative process mineralogy strategies and to implement on-line procedures at processing level. The present study discusses the effects related to the adoption of different hardware configurations, the utilization of different logics to perform the analysis and the selection of different algorithms according to the different characterization, inspection and quality control actions to apply.

  10. Recent Developments in the Treatment of Uranium Ores from the Elliot Lake District

    Energy Technology Data Exchange (ETDEWEB)

    Downes, K W [Extraction Metallurgy Division, Department of Mines and Technical Surveys, Ottawa (Canada)

    1967-06-15

    A summary of the results obtained during investigations on the treatment of uranium ores from the Elliot Lake district in the laboratories of the Mines Branch, and of developments in operating procedures introduced in the uranium mills in the Elliot Lake district, is presented. Concentration of Elliot Lake ore on a pilot-plant scale by a combined gravity-flotation procedure yielded a 90% recovery of uranium at a ratio of concentration of 2.4 to 1.0. The mineralogical composition of the ore, the flow sheet used and the reagents employed are described. An approximate cost estimate indicates that, although the capacity of an existing uranium leaching plant would be doubled by introducing the procedure, the production cost per pound of U{sub 3}0{sub 8} would not be affected. Bacterial leaching of Elliot Lake ore on a laboratory scale yielded, under favourable conditions, extractions of 90 per cent in 5 weeks, and of 95 per cent in 15 weeks. The conditions that were found to influence the leaching results are outlined, and the effects of the leaching solutions are discussed. The purification of ion exchange eluates by liquid-liquid extraction, using tri-n-butyl phosphate, dibutyl butylphosphonate and tri-capryl amine in a continuous process, yielded solutions from which refined ammonium diuranate was precipitated using gaseous ammonia. The effectiveness of the three extractants is discussed, and the effects of the procedures employed on the production costs per pound of U{sub 3}O{sub 8} is estimated. Some improvements in operating procedures introduced in the Elliot Lake district uranium mills are briefly described, and their effects on the operations are indicated. Present methods of controlling radiological pollution of drainage waters by uranium mill tailings are outlined. (author)

  11. Chlorine/chloride based processes for uranium ores

    International Nuclear Information System (INIS)

    1980-11-01

    The CE Lummus Minerals Division was commissioned by The Department of Supply and Services to develop order-of-magnitude capital and operating cost estimates for chlorine/chloride-based processes for uranium ores. The processes are designed to remove substantially all radioactive consituents from the ores to render the waste products harmless. Two processes were selected, one for a typical low grade ore (2 lb. U 3 O 8 /ton ore) and one for a high grade ore (50 lbs U 3 O 8 /ton). For the low grade ore a hydrochloric acid leaching process was chosen. For high grade ore, a more complex process, including gaseous chlorination, was selected. Capital cost estimates were compiled from information obtained from vendors for the specified equipment. Building cost estimates and the piping, electrical and instrumentation costs were developed from the plant layout. Utility diagrams and mass balances were used for estimating utilities and consumables. Detailed descriptions of the bases for capital and operating cost estimates are given

  12. Aqueous-chlorine leaching of typical Canadian uranium ores

    International Nuclear Information System (INIS)

    Haque, K.E.

    1982-01-01

    Laboratory-scale aqueous-chlorine leaches were conducted on quartz-pebble conglomerates, pegmatite and vein-type ores. Optimum leach temperatures, pulp density and retention times were determined. Uranium extraction of 98 per cent was obtained from the Elliot Lake, Madawaska Mines of Bancroft and Rabbit Lake ores, 96 per cent from the Key Lake ore and 86 per cent from the Agnew Lake ore. However, tailings containing 15-20 pCi g -1 of radium-226 were obtained only from the Elliot Lake and Agnew lake quartz-pebble conglomerates and Bancroft pegmatite-type ores by second-stage leaches with HCl. The second-stage leach results indicate that multistage (3 or 4) acid-chloride or salt-chloride leaches might be effective to obtain tailings containing 15-20 pCi 226 Ra g -1 from the high-grade vein-type ores. Comparative reagent-cost estimates show that the sulphuric-acid leach process is far less expensive than aqueous chlorine leaching. Nevertheless, only the aqueous chlorine and acid-chloride leaches in stages are effective in producing tailings containing 15-20 pCi 226 Ra g -1 from the typical Canadian uranium ores. (Auth.)

  13. Beneficiation studies on low-grade complex polymetallic lead-zinc ore of duddar (lasbela) Balochistan, Pakistan

    International Nuclear Information System (INIS)

    Bhatti, M.R.; Kazim, K.R.; Mehmood, R.; Akram, A.

    2016-01-01

    A bench-scale beneficiation study was performed on low-grade complex lead-zinc ore of Duddar area, District Lasbela, Balochistan Province, Pakistan. The polymetallic ore under investigation contains galena and sphalerite as valuable minerals of lead and zinc. The low-grade ore was upgraded by selective sequential froth flotation technology to recover both minerals. An effort was made to investigate the effect of important variables on grade and recovery of concentrates and to design the process flow sheet. Different parameters of flotation process such as particle size of the feed, pH and % solids of the pulp, speed of impeller, type of reagents (collectors, frothers, regulators and modifiers) and their quantities, conditioning time and flotation time were optimized to attain maximum grade and recovery of respective concentrates. The rougher concentrates obtained were subjected to one regrinding and two cleaning operations to achieve higher-grade concentrates of both metals. Bench-scale flotation tests show that it is possible to obtain a lead concentrate assaying 65.24% Pb with recovery rate of 81.32% and a zinc concentrate containing 55.63% Zn content with recovery rate of 80.28%. Both the concentrates meet the specifications required for metallurgical and chemical grades. (author)

  14. Discussion on the impact of uranium ore heap leaching to environment

    International Nuclear Information System (INIS)

    Qin Guoxiu; Liu Qingcheng; Chen Xin; Deng Shengshui; Yang Qinghua

    2012-01-01

    In this paper, the impact of uranium ore heap leaching on the environment were studied with the case of two long production uranium mines. According to the basic requirements of the radiation environment assessment of the nuclear industry, the surface radon exhalation rate of the mine waste, the concentration of radionuclide of the waste water and the γ radiation level and concentration of radionuclide of the waste were investigated and compared to that of the early conventional hydrometallurgical production of the two uranium mines. The merits and disadvantage of the heap leaching was evaluated, and measures and suggestions were proposed for the improvement of heap leaching techniques. (authors)

  15. Experimental and theoretical investigations on diffusion process for rare earth ores

    Energy Technology Data Exchange (ETDEWEB)

    He, Ye; Li, Wenzhi Z. [Changchun Univ. (China)

    2013-06-01

    The diffusion reaction kinetics of weathered crust elution-deposited rare earth with mixed ammonium salts was studied. The influence of concentration of reagents and particle size of ore on diffusion rate was investigated. The results showed that the diffusion process and diffusion rate could be improved by increasing reagents concentration and decreasing diffusion flowing rate and particle size. The diffusion process could be explained with the shrinking core Model, which could be controlled by the diffusion rate of reacting reagents in porous solid layer.

  16. Determination of rhenium in ores of complex composition by the kinetic method

    Energy Technology Data Exchange (ETDEWEB)

    Pavlova, L G; Gurkina, T V [Kazakhskij Gosudarstvennyj Univ., Alma-Ata (USSR); Tsentral' naya Lab. Yuzhno-Kazakhstanskogo Geologicheskogo Upravleniya, Alma-Ata (USSR))

    1979-09-01

    The kinetic rhenium determination method is proposed based on rhenium catalytic effect in the reaction of malachite green with thiourea. The accompanying elements, excluding molybdenum, do not interfere with the rhenium determination at their concentration of up to 0.1 M. The interfering influence of molybdenum can be eliminated by addition of tartaric acid to the solution up to the concentration of 0.1 M. This enables to determine rhenium in presence of 1000-fold quantity of molybdenum. The method is applicable for the analysis of complex copper-zinc sulphide ores.

  17. Effect of desliming on the flotation of a complax copper ore from China

    OpenAIRE

    Chen Yong; Song Yong Sheng; Li Wen Juan; Zhou Gui Ying

    2016-01-01

    The complex copper oxide ore sample was taken from Deerni copper deposit, Qinghai Province of China. Batch flotation tests had been conducted to upgrade the copper concentrate by conventional amyl xanthate reagents under 73% -74 μm of the particle size; however, the unsatisfied results (Cu grade of 18.21% and recovery of 59.25%) were obtained. Also there are a large amount of slimes trapped in the concentrate and high-dosages consumption of reagents, for example, more than 2.5 kg/t sodium sul...

  18. Influence of ore processing activity on Hg, As and Sb contamination and fractionation in soils in a former mining site of Monte Amiata ore district (Italy).

    Science.gov (United States)

    Protano, Giuseppe; Nannoni, Francesco

    2018-05-01

    A geochemical study was carried out at the former Abbadia San Salvatore (ASS) mining site of the Monte Amiata ore district (Italy). Hg, As and Sb total contents and fractionation using a sequential extraction procedure were determined in soil and mining waste samples. Ore processing activities provided a different contribution to Hg contamination and concentration in soil fractions, influencing its behaviour as volatility and availability. Soils of roasting zone showed the highest Hg contamination levels mainly due to the deposition of Hg released as Hg 0 by furnaces during cinnabar roasting. High Hg contents were also measured in waste from the lower part of mining dump due to the presence of cinnabar. The fractionation pattern suggested that Hg was largely as volatile species in both uncontaminated and contaminated soils and mining waste, and concentrations of these Hg species increased as contamination increased. These findings were in agreement with the fact that the ASS mining site is characterized by high Hg concentrations in the air and the presence of Hg 0 liquid droplets in soil. Volatile Hg species were also prevalent in uncontaminated soils likely because the Monte Amiata region is an area characterized by anomalous fluxes of gaseous Hg from natural and anthropogenic inputs. At the ASS mining site soils were also contaminated by Sb, while As contents were comparable with its local background in soil. In all soil and waste samples Sb and As were preferentially in residual fraction. Copyright © 2018 Elsevier Ltd. All rights reserved.

  19. Multi-column bioleaching of a uranium ore

    International Nuclear Information System (INIS)

    Meng Yunsheng; Zheng Ying; Liu Hui; Cheng Hao

    2014-01-01

    The technology of bioleaching uranium ore can increase the uranium leaching rate and shorten the leaching uranium period, save consumption of acid and oxidant, lower production costs. An experiment on multi-column bioleaching of a uranium ore was done using mesophilic bacteria, the average uranium recovery of 90% was achieved in 39 days. Compared with traditional process, leaching period was shortened to 39 d from 59 d, acid consumption and liquid-solid ratio were also reduced. The results showed it is suitable to bioleach the uranium ore. (authors)

  20. Mining and processing of uranium ores in the USSR

    International Nuclear Information System (INIS)

    Laskorin, B.N.; Mamilov, V.A.; Korejsho, Yu.A.

    1983-01-01

    Experience gained in uranium ore mining by modern methods in combination with underground and heap leaching is summarized. More intensive processing of low-grade ores has been achieved through the use of autoclave leaching, sorptive treatment of thick pulps, extractive separation of pure uranium compounds, automated continuous sorption devices of high efficiency for processing the underground- and heap-leaching liquors, natural and mine water, and recovery of molybdenum, vanadium, scandium, rare earths and phosphate fertilizers from low-grade ores. Production of ion-exchangers and extractants has been developed and processes for concomitant recovery of copper, gold, ionium, tungsten, caesium, zirconium, tantalum, nickel and cobalt have been designed. (author)

  1. Influence of Stockpile Angle in Natural Drying of Laterite Ore

    Directory of Open Access Journals (Sweden)

    Yoalbys Retirado-Mediaceja

    2016-10-01

    Full Text Available Natural drying is performed at Cuban nickel plants by depositing bulk ore in the open. The ore is currently being stockpiled without much consideration for the impact of the drying surface angle on the process power behavior. Simulations were carried out in this investigation, which prove that an increased triangular stockpile angle considerably reduces natural drying efficiency. A 45 sexagesimal degree angle to the horizontal plane results in exposure of a large volume of ore to natural drying and guarantees adequate energy performance.

  2. Biosolubilization of uranyl ions in uranium ores by hydrophyte plants

    International Nuclear Information System (INIS)

    Cecal, Alexandru; Calmoi, Rodica; Melniciuc-Puica, Nicoleta

    2006-01-01

    This paper investigated the bioleaching of uranyl ions from uranium ores, in aqueous medium by hydrophyte plants: Lemna minor, Azolla caroliniana and Elodea canadensis under different experimental conditions. The oxidation of U(IV) to U(VI) species was done by the atomic oxygen generated in the photosynthesis process by the aquatic plants in the solution above uranium ores. Under identical experimental conditions, the capacity of bioleaching of uranium ores decreases according to the following series: Lemna minor > Elodea canadensis > Azolla caroliniana. The results of IR spectra suggest the possible use of Lemna minor and Elodea canadensis as a biological decontaminant of uranium containing wastewaters. (author)

  3. Determination of the oxidizing capacity of manganese ores.

    Science.gov (United States)

    Prasad, R

    1974-09-01

    An accurate method is described for determining the amount of active oxygen in manganese ores, based on the oxidation-reduction reaction between the ore and arsenic(III) in presence of ammonium molybdate, followed by the back-titration of excess of arsenic(III) with cerium(IV), using osmium tetroxide as catalyst and Disulphine Blue V as indicator. A survey has been made of the applicability of this method to various pyrolusite ores containing less than 0.2% phosphorus. Aluminium(III), copper(II), iron(III), manganese(II), and molybdenum(VI) do not interfere. Up to 30% phosphorus(V) causes no interference.

  4. Current methods and possibilities to determine the variability of Cu content in the copper ore on a conveyor belt in one of KGHM Polska Miedz S.A. mines

    Directory of Open Access Journals (Sweden)

    Jurdziak Leszek

    2016-01-01

    Full Text Available In this paper the methodology of ore sampling on a belt conveyor in one of KGHM Polska Miedz S.A. mines was presented together with the results of analysis of the variation of ore tonnage and quality. The ore was transferred from one mine to another one through the analysed transfer conveyor on the route from the mine Division of Mining to copper plants. The transported ore was sampled in person from Division of Concentrators on a regular basis for metal accounting purposes between both mines. The ore quality control became a significant problem since it is impossible to predict with satisfactory advance both Cu content in the feed as well as its lithology composition which is required to improve and optimise the enrichment efficiency.

  5. The effect of iron-ore particles on the metal content of the brown alga Padina gymnospora (Espirito Santo Bay, Brazil)

    International Nuclear Information System (INIS)

    Nassar, C.A.G.; Salgado, L.T.; Yoneshigue-Valentin, Y.; Amado Filho, G.M.

    2003-01-01

    Iron ore deposits mat be the source of metals found in the brown alga Padina gymnospora. - The iron-ore particles discharged by a pellet processing plant (Espirito Santo Bay, Brazil) cover the seabed of Camburi Beach and consequently, the epibenthic community. In order to determine the importance of the contribution of the iron-ore deposits to the metal concentration in macroalgae of Espirito Santo Bay, four methods of cleaning particulate material adhered to the surface of thalli were tested prior to metal tissue analysis (Al, Cd, Cr, Cu, Fe, Mn, Ni, Pb and Zn) of Padina gymnospora. In addition, heavy metal concentrations were determined in individuals of P. gymnospora from a site (Frade Island) not affected by the iron-ore particles. The most efficient cleaning treatment, a combination of scraping and washing with an ethanol-seawater solution (NA+SC+ET) removed a number of particles on the surface of thalli 10 times higher than that observed in the control (C). Using this treatment, the total-metal concentrations were reduced by 78% for Fe and 50% for Al respect to the control. However, Fe, Al and Cu concentrations after treatment NA+SC+ET were significantly higher than those found at Frade Island. It is suggested that the iron-ore deposit might be a source for metal availability to macroalgae exposed to the dumped material at Espirito Santo Bay

  6. Difference of ore-bearing and non-ore-bearing pegmatite in the Guangshigou area and its research significance

    International Nuclear Information System (INIS)

    Zuo Wenqian; Zhang Zhanshi; Sha Yazhou; Rao Chaojun

    2011-01-01

    Guangshigou uranium deposit is one of the typical granite-pegmatite uranium deposits in China, the ore-body are located in the density zone of the outside contact zone of granite pluton. To distinguish the ore-bearing and Non-ore-bearing pegmatite is one of the most practices and have great significance for the effect of mineral exploration. Based on the field investigation and former research results, contrast research on the characteristics of the pegmatite on petrology, geophysical, geochemistry and stable isotopes have been carried out. It is pointed out that the ore-bearing pegmatite differ from the non-ore-bearing one from macro-and-micro-view in Guangshigou Uranium deposits, the main characteristics are summarized; the macro-and-micro signs are established, the genetic difference between the ore-bearing and non-ore-bearing pegmatite are discussed primarily. The achievements would be helpful for prospecting and researching of this type uranium deposits in China. (authors)

  7. Ore-forming environment and ore-forming system of carbonaceous-siliceous-pelitic rock type uranium deposit in China

    International Nuclear Information System (INIS)

    Qi Fucheng; Zhang Zilong; Li Zhixing; He Zhongbo; Wang Wenquan

    2012-01-01

    It is proposed that there are four types of ore-forming systems about carbonaceous-siliceous-pelitic rock type uranium deposit in China based on systematic study on structural environment and distribution regularity of uraniferous construction of marine carbonaceous-siliceous-pelitic rock in China: continental margin rift valley ore-forming systems, continental margin rifting deep fracture zone ore-forming systems, landmass boundary borderland basin ore-forming systems and epicontinental mobile belt downfaulted aulacogen ore-forming systems. It is propounded definitely that it is controlled by margin rift valley ore-forming systems and continental margin rifting deep fracture zone ore-forming systems for large-scale uranium mineralization of carbonaceous-siliceous-pelitic rock type uranium deposit in China, which is also controlled by uraniferous marine carbonaceous-siliceous-pelitic rock construction made up of silicalite, siliceous phosphorite and carbonaceous-siliceous-pelitic rock, which settled down accompany with submarine backwash and sub marine volcanic eruption in margin rift valley and continental margin rifting mineralizing environment. Continental mar gin rift valley and continental margin rifting thermal sedimentation or exhalation sedimentation is the mechanism of forming large-scale uraniferous marine carbonaceous-siliceous-pelitic rock construction Early Palaeozoic Era in China or large-scale uranium-polymetallic mineralization. (authors)

  8. Thiosulphate leaching of gold-, silver-, copper flotation concentrates

    International Nuclear Information System (INIS)

    Samikhov, Sh.R.; Zinchenko, Z.A.

    2015-01-01

    Present article is devoted to thiosulphate leaching of gold-, silver-, copper flotation concentrates. For the purpose to improve the process of thiosulphate leaching the ore samples were calcined at temperature 600 ℃ during two hours. During the calcination process of gold-sulphide ores and concentrates the minerals pyrite and arsenopyrite oxidize which lead to opening of gold contains in them. It was defined that thiosulphate leaching can be recommended as an alternative to cyanic process.

  9. Functional activity of microorganisms in mining and processing of copper-nickel ores in the Murmansk Region

    Directory of Open Access Journals (Sweden)

    Fokina N. V.

    2018-03-01

    Full Text Available The quantitative indices and structure of the microbial community in flotation samples of sulfide copper-nickel ores at concentration plant of Kola Mining and Metallurgical Company have been determined. The smallest number of saprotrophic and oligotrophic bacteria has been observed in samples of ore and recycled water, which can be explained by the low temperature of samples and the lack of nutrients. It has been found out that the bacteria contained in the ore and recycling water flowing from the tailings increased their number during the flotation process due to coming of the organic compounds with the flotation reagents, aeration and increased temperature. Dominating strains have been isolated from recycled water and basic flotation products and classified as Pseudomonas. It has been shown that with an increase in the number of bacteria, the flotation time of copper-nickel ores increases. There is also a tendency to change the extraction of copper and nickel, which can be caused by both the increase in the flotation time for operations and the change in the number of bacteria in the circulating water. The thionic bacteria have been distinguished from the flow tailings of the Allarechensk deposit. The heap leaching experiments have proved the bacterial leaching to give good results on the ore samples passed through magnetic separation, having shown high content of the nickel and copper in filters. When leaching low-grade ore of the Nude Terrasa, the advantage of bacterial leaching use in comparison with the sulphuric-acid leaching only to copper has been revealed. The nickel content in the filtrates for bacterial leaching is 275 mg/l, and for sulfuric acid – 310 mg/l. The average copper content in the filtrates is 19 and 15 mg/l.

  10. Experiment on bio-leaching of associated molybdenum and uranium ore

    International Nuclear Information System (INIS)

    Zheng Ying; Fan Baotuan; Liu Jian; Meng Yunsheng; Liu Chao

    2007-01-01

    Column leaching experiment results on associated molybdenum uranium ore by bacteria (T. f) are introduced. The ore are leached for 210 days using bacteria domesticated to tolerate molybdenum, the leaching of uranium is of 98% and leaching of molybdenum is of 41%. Sulphuric acid produced by bio-oxidation of sulfides in ore can meet the demand of ore leaching. (authors)

  11. 40 CFR 440.40 - Applicability; description of the mercury ore subcategory.

    Science.gov (United States)

    2010-07-01

    ... mercury ore subcategory. 440.40 Section 440.40 Protection of Environment ENVIRONMENTAL PROTECTION AGENCY (CONTINUED) EFFLUENT GUIDELINES AND STANDARDS ORE MINING AND DRESSING POINT SOURCE CATEGORY Mercury Ore Subcategory § 440.40 Applicability; description of the mercury ore subcategory. The provisions of subpart D...

  12. Invisible and microscopic gold in pyrite: Methods and new data for massive sulfide ores of the Urals

    Science.gov (United States)

    Vikentyev, I. V.

    2015-07-01

    Au speciation in sulfides (including "invisible" Au), which mostly controls the loss of Au during ore dressing, is discussed. Modern methods of analysis of Au speciation, with discussion of limitations by locality and sensitivity, are reviewed. The results of sulfide investigation by the methods of scanning and transmission electron microscopy, mass spectrometric analysis with laser ablation (LA-ICP-MS), the thermochemical method (study of ionic Au speciation), and automated "quantitative mineralogy," are demonstrated for weakly metamorphosed VHMS deposits of the Urals (Galkinsk and Uchaly). Significant content of Au is scattered in sulfides, such as pyrite, chalcopyrite, and sphalerite, with quantitative predomination of pyrite. The portion of such "invisible" gold ranges from flakes) with a monocrystal diffraction pattern of some particles and a ring diffraction pattern of other particles was registered in the ores of these deposits by the methods of transmission electron microscopy. The low degree (or absence) of metamorphic recrystallization results in (1) predomination of thin intergrowths of sulfides, which is the main reason for the bad concentration of ores (especially for the Galkinsk deposit) and (2) the high portion of "invisible" gold in the massive sulfide ores, which explains the low yield of Au in copper and zinc concentrates, since it is lost in tailings with predominating pyrite.

  13. Lead isotope results of acid leaching experiments on acid volcanics and black shales in an ore environment

    International Nuclear Information System (INIS)

    Gulson, B.L.

    1977-01-01

    In the volcanogenic Woodlawn Cu-Pb-Zn deposit, where pyrite is the dominant sulphide phase in the ore and a ubiquitous mineral in the host volcanics and shales, leaching experiments using HNO 3 -HCl to overcome the ore/rock lead dominance, resulted in highly complex lead isotopic data, dependent mainly on the original lead concentration in the rock. For samples with higher (> 5 ppm) lead concentrations, the acid leaches are less radiogenic than the rocks or residues whereas for samples with 15 ppm lead, the data arrays are those expected for a dominance of ore/rock lead. In all except the very high lead samples (> 100 ppm), lead is derived from sources other than sulphides. Furthermore, in only the highest lead sample is the acid leach isotopic value compatible with that of the ore lead. As found in previous leaching investigations, the dominant component of lead and uranium is extracted in the acid leach. Acid-leaching experiments of this type may have possible applications in prospecting for basemetal sulphides. (auth.)

  14. Effects of barium chlorine treatment of uranium ore on 222Rn emanation and 226Ra leachability from mill tailings

    International Nuclear Information System (INIS)

    Ibrahim, S.A.; Church, S.L.; Whicker, F.W.

    1985-01-01

    The purpose of this laboratory study was to investigate the effectiveness of barium chloride treatment of uranium ore on 222 Rn emanation from mill tailings, 226 Ra level in waste-water, and the leachability of radium from tailings. It has been shown that barium sulfate is an excellent carrier for radium and that barium sulfate crystals have high retention capacity for radon gas produced by radium trapped within the lattice. Ground uranium ore from a mine in Wyoming was mixed with water to form a 1:1 ratio before barium and potassium chlorides were added at concentrations of 0, 10, 25, 50, and 100 mg per liter of slurry. The ore was then subjected to a simulated mill process using sulfuric acid leaching. The liquid representing tailings pond water was separated and analyzed for 226 Ra and the solid fraction, representing mill tailings, was tested for radon emanation and the leachability of radium by deionized water. This study suggests that barium treatment of uranium ore prior to sulfuric acid leaching could be effective in reducing radon emanation from tailings and also in reducing the 226 Ra concentration of waste-water. Leachability of radium from treated tailings was markedly reduced

  15. Ore loses and dilution of the ore vein no. 4 in the Zletovo mine, Republic of Macedonia

    Directory of Open Access Journals (Sweden)

    Bogatinovski Nikola L.

    2017-01-01

    Full Text Available Zletovo mines have a tradition of exploration and exploitation of vein lead-zinc ores for almost a century. Ore losses and dilutions have always been imperative in production since traditional old methods of mining and low-productivity mineralization are used. In conditions of classical and sub-level method excavations used, the calculated ore losses in ore vein No. 4 are 13.5%, while at the level of all excavations in the Zletovo mines dilution averages at 10%. Ore dilution is also an important technical parameter and several possible variants were calculated. When analyzing the dilution that occurs during the preparation of the sub-level corridor with parameters such: different drop angle (45-60o, constant thickness of 1.47 m as the average vein thickness in the calculated ore reserves, width of the sub-level corridor of 1.57 m or to the width of the ore vein No. 4 were added 10 cm (left and right to 5 cm as much as is taken in the calculation of the planned dilution and height of 2.5 m as suggested for this mining method, it can be noticed that the planned dilution during this method of mining ranges from 26.3% to 42.3%. In conditions of use of this underground method of excavation, parameters are selected that allow for the indicated lowering of the dilution. Namely, the thickness of the ore wire would be 1.47 m, the mining width would be 1.57 m, only 10 cm (left and right up to 5cm to the thickness of the ore vein will be added, the height difference between the consecutive levels would be 7.5 m, dip angle of 45 to 60°, and with the excavation the whole ore vein would be covered in height. On the basis of these parameters, models were prepared in which the ore vein would have a different dip angle, from which the values for the planned ore dilution ranged from 6.7 to 7.8%, which is significantly lower than the average dilution in the Zletovo Mine.

  16. Total Ore Processing Integration and Management

    Energy Technology Data Exchange (ETDEWEB)

    Leslie Gertsch

    2006-05-15

    This report outlines the technical progress achieved for project DE-FC26-03NT41785 (Total Ore Processing Integration and Management) during the period 01 January through 31 March of 2006. (1) Work in Progress: Minntac Mine--Graphical analysis of drill monitor data moved from two-dimensional horizontal patterns to vertical variations in measured and calculated parameters. The rock quality index and the two dimensionless ({pi}) indices developed by Kewen Yin of the University of Minnesota are used by Minntac Mine to design their blasts, but the drill monitor data from any given pattern is obviously not available for the design of that shot. Therefore, the blast results--which are difficult to quantify in a short time--must be back-analyzed for comparison with the drill monitor data to be useful for subsequent blast designs. {pi}{sub 1} indicates the performance of the drill, while {pi}{sub 2} is a measure of the rock resistance to drilling. As would be expected, since a drill tends to perform better in rock that offers little resistance, {pi}{sub 1} and {pi}{sub 2} are strongly inversely correlated; the relationship is a power function rather than simply linear. Low values of each Pi index tend to be quantized, indicating that these two parameters may be most useful above certain minimum magnitudes. (2) Work in Progress: Hibtac Mine--Statistical examination of a data set from Hibtac Mine (Table 1) shows that incorporating information on the size distribution of material feeding from the crusher to the autogenous mills improves the predictive capability of the model somewhat (43% vs. 44% correlation coefficient), but a more important component is production data from preceding days (26% vs. 44% correlation coefficient), determined using exponentially weighted moving average predictive variables. This lag effect likely reflects the long and varied residence times of the different size fragments in the grinding mills. The rock sizes are also correlated with the geologic

  17. Continued Multicolumns Bioleaching for Low Grade Uranium Ore at a Certain Uranium Deposit

    Directory of Open Access Journals (Sweden)

    Gongxin Chen

    2016-01-01

    Full Text Available Bioleaching has lots of advantages compared with traditional heap leaching. In industry, bioleaching of uranium is still facing many problems such as site space, high cost of production, and limited industrial facilities. In this paper, a continued column bioleaching system has been established for leaching a certain uranium ore which contains high fluoride. The analysis of chemical composition of ore shows that the grade of uranium is 0.208%, which is lower than that of other deposits. However, the fluoride content (1.8% of weight is greater than that of other deposits. This can be toxic for bacteria growth in bioleaching progress. In our continued multicolumns bioleaching experiment, the uranium recovery (89.5% of 4th column is greater than those of other columns in 120 days, as well as the acid consumption (33.6 g/kg. These results indicate that continued multicolumns bioleaching technology is suitable for leaching this type of ore. The uranium concentration of PLS can be effectively improved, where uranium recovery can be enhanced by the iron exchange system. Furthermore, this continued multicolumns bioleaching system can effectively utilize the remaining acid of PLS, which can reduce the sulfuric acid consumption. The cost of production of uranium can be reduced and this benefits the environment too.

  18. Quantitative Investigation of Roasting-magnetic Separation for Hematite Oolitic-ores: Mechanisms and Industrial Application

    Directory of Open Access Journals (Sweden)

    Peng Tiefeng

    2017-12-01

    Full Text Available Natural high-quality iron can be directly applied to pyro-metallurgy process, however, the availability of these ores has become less and less due to exploitation. This research reports a systematic approach using reduction roasting and magnetic separation for oolitic iron ores from west Hubei Province. Firstly, a mineralogical study was performed and it was shown that the oolitic particles were mainly composed of hematite, with some silicon-quartz inside the oolitic particle. Then, the roasting temperature was examined and shown to have significant influence on both Fe recovery and the Fe content of the concentrate. Also the Fe content gradually increased as the temperature increased from 700 to 850 °C. The most important aspects are the quantitative investigation of change of mineral phases, and reduction area (with ratio during the reduction roasting process. The results showed that Fe2O3 decreased with temperature, and Fe3O4 (magnetite increased considerably from 600 to 800 °C. The reductive reaction was found to occur from the outside in, the original oolitic structure and embedding relationship among the minerals did not change after roasting. Finally, 5% surrounding rock was added to mimic real industrial iron beneficiation. This study could provides useful insight and practical support for the utilization of such iron ores.

  19. A multidimensional analysis and modelling of flotation process for selected Polish lithological copper ore types

    Directory of Open Access Journals (Sweden)

    Niedoba Tomasz

    2017-01-01

    Full Text Available The flotation of copper ore is a complex technological process that depends on many parameters. Therefore, it is necessary to take into account the complexity of this phenomenon by choosing a multidimensional data analysis. The paper presents the results of modelling and analysis of beneficiation process of sandstone copper ore. Considering the implementation of multidimensional statistical methods it was necessary to carry out a multi-level experiment, which included 4 parameters (size fraction, collector type and dosage, flotation time. The main aim of the paper was the preparation of flotation process models for the recovery and the content of the metal in products. A MANOVA was implemented to explore the relationship between dependent (β, ϑ, ε, η and independent (d, t, cd, ct variables. The design of models was based on linear and nonlinear regression. The results of the variation analysis indicated the high significance of all parameters for the process. The average degree of matching of linear models to experimental data was set at 49% and 33% for copper content in the concentrate and tailings and 47% for the recovery of copper minerals in the both. The results confirms the complexity and stochasticity of the Polish copper ore flotation.

  20. Separation and recovery of uranium ore by chlorinating, chelate resin and molten salt treatment

    International Nuclear Information System (INIS)

    Taki, Tomohiro

    2000-12-01

    Three fundamental researches of separation and recovery of uranium from uranium ore are reported in this paper. Three methods used the chloride pyrometallurgy, sodium containing molten salts and chelate resin. When uranium ore is mixed with activated carbon and reacted for one hour under the mixed gas of chlorine and oxygen at 950 C, more than 90% uranium volatilized and vaporization of aluminum, silicone and phosphorus were controlled. The best activated carbon was brown coal because it was able to control the large range of oxygen concentration. By blowing oxygen into the molten sodium hydroxide, the elution rate of uranium attained to about 95% and a few percent of uranium was remained in the residue. On the uranium ore of unconformity-related uranium deposits, a separation method of uranium, molybdenum, nickel and phosphorus from the sulfuric acid elusion solution with U, Ni, As, Mo, Fe and Al was developed. Methylene phosphonic acid type chelate resin (RCSP) adsorbed Mo and U, and then 100 % Mo was eluted by sodium acetate solution and about 100% U by sodium carbonate solution. Ni and As in the passing solution were recovered by imino-diacetic acid type chelate resin and iron hydroxide, respectively. (S.Y.)

  1. Estimated water requirements for the conventional flotation of copper ores

    Science.gov (United States)

    Bleiwas, Donald I.

    2012-01-01

    This report provides a perspective on the amount of water used by a conventional copper flotation plant. Water is required for many activities at a mine-mill site, including ore production and beneficiation, dust and fire suppression, drinking and sanitation, and minesite reclamation. The water required to operate a flotation plant may outweigh all of the other uses of water at a mine site, [however,] and the need to maintain a water balance is critical for the plant to operate efficiently. Process water may be irretrievably lost or not immediately available for reuse in the beneficiation plant because it has been used in the production of backfill slurry from tailings to provide underground mine support; because it has been entrapped in the tailings stored in the TSF, evaporated from the TSF, or leaked from pipes and (or) the TSF; and because it has been retained as moisture in the concentrate. Water retained in the interstices of the tailings and the evaporation of water from the surface of the TSF are the two most significant contributors to water loss at a conventional flotation circuit facility.

  2. Radioanalysis of RE enrichment of ion adsorption type RE ores

    CERN Document Server

    Zhao Shu Quan; Hu He Ping; Li Fu Sheng; Chen Ying Min; LiuShiMing

    2002-01-01

    Objective: To analyze the radioactivity in Rare Earth (RE) enrichment of ion adsorption type RE ores. Methods: Using HPGe-gamma spectrometer to analyze the activity ratio of gamma radionuclides in kind of samples, using FJ-2603 low background alpha, beta measurement apparatus to measure their total alpha and total beta activities, and using X-ray fluorescence spectrometer to analyze contents of La sub 2 O sub 3 and Y sub 2 O sub 3 , respectively. Results: HPGe gamma spectroscopy and X-ray fluorescence spectroscopy are simple, convenient and non-destructive methods of analyzing radionuclides and La sub 2 O sub 3 , Y sub 2 O sub 3 in RE enrichment of ion adsorption type RE ores, respectively. Conclusion: The basic data were provided for radiation protection and treatment of gas, liquid and solid waste in RE production of ion adsorption type RE ores; method and experience were provided for studying ion adsorption type RE ores

  3. Arsenic bioleaching in medical realgar ore and arsenic- bearing ...

    African Journals Online (AJOL)

    Oxidation of these two ores by sulfuric acid was insignificant, as maximum arsenic leaching ratios ... Poor water solubility and weak gastrointestinal absorption of coarse ..... Wu XH, Sun DH, Zhuang ZX, Wang XR, Gong HF, Hong. JX, Lee FSC.

  4. chemical and mineralogical characterization of lateritic iron ore

    African Journals Online (AJOL)

    DJFLEX

    2010-04-22

    Apr 22, 2010 ... The laterite iron ore deposit at Auchi, Edo State, Nigeria was studied chemically and mineralogically. The results of the chemical ... SAMPLE PREPARATION. The samples .... 2µm) and were subjected to X-ray diffraction using.

  5. By lithology Zbruch deposits (Lower Sarmatian Nikopol manganese ore Basin

    Directory of Open Access Journals (Sweden)

    Bogdanovich V.V.

    2010-06-01

    Full Text Available Based on lithologic-paleogeographic study Zbruch layers of Nikopol manganese ore Basin sediments described lithological and genetic types of rocks and facies conditions of formation of deposits.

  6. Pulmonary function evaluations of dogs exposed to uranium ore dust

    International Nuclear Information System (INIS)

    Loscutoff, S.M.; Buschbom, R.L.; Palmer, R.F.; Cross, F.T.

    1980-01-01

    Pulmonary function evaluations were conducted on dogs exposed to carnotite uranium ore dust. Significant changes were detected in the slope of the single-breath N 2 washout curve, suggesting an uneven distribution of ventilation

  7. Comparison of oxidants in alkaline leaching of uranium ore

    International Nuclear Information System (INIS)

    Sreenivas, T.; Rajan, K.C.; Srinivas, K.; Anand Rao, K.; Manmadha Rao, M.; Venkatakrishnan, R.R.; Padmanabhan, N.P.H.

    2007-01-01

    The uranium minerals occurring in various ore deposits consists of predominantly uranous ion (U +4 ), necessitating use of an oxidant and other lixiviants for efficient dissolution during leaching. Unlike acid leaching route, where uranium minerals dissolution could be achieved efficiently with cheaper lixiviants, processing of ores by alkaline leaching route involve expensive lixiviants and drastic leaching conditions. Alkaline leaching of uranium ores becomes economical only upon using cheaper and efficient oxidants and conservation of other reagents by their recycle. The present paper gives efficacy of various oxidants - KMnO 4 , NaOCl, Cu - NH 3 , air and oxygen, in the leaching of uranium from a low-grade dolostone hosted uranium ore of India. A comparison based on technical merits and cost of the oxidant chemicals is discussed. (author)

  8. Mössbauer Spectral Data of Vermiculite Ore

    Data.gov (United States)

    Department of the Interior — Data are provide for four samples of unexpanded vermiculite ore from mines near Enoree, South Carolina; Libby, Montana; Louisa, Virginia; Palabora, and South Africa....

  9. Biomineral processing of high apatite containing low-grade indian uranium ore

    Energy Technology Data Exchange (ETDEWEB)

    Abhilash; Mehta, K.D.; Pandey, B.D., E-mail: biometnml@gmail.com [National Metallurgical Laboratory (CSIR), Jamshedpur (India); Ray, L. [Jadavpur Univ., FTBE Dept., Kolkata (India); Tamrakar, P.K. [Uranium Corp. of India Limited, CR& D Dept., Jaduguda (India)

    2010-07-01

    Microbial species isolated from source mine water, primarily an enriched culture of Acidithiobacillus ferrooxidans was employed for bio-leaching of uranium from a low-grade apatite rich uranium ore of Narwapahar Mines, India while varying pH, pulp density (PD), particle size, etc. The ore (0.047% U{sub 3}O{sub 8}), though of Singhbhum area (richest deposit of uranium ores in India), due to presence of some refractory minerals and high apatite (5%) causes a maximum 78% recovery through conventional processing. Bioleaching experiments were carried out by varying pH at 35{sup o}C using 20%(w/v) PD and <76μm size particles resulting in 83.5% and 78% uranium bio-recovery at 1.7 and 2.0 pH in 40 days as against maximum recovery of 46% and 41% metal in control experiments respectively. Finer size (<45μm) ore fractions exhibited higher uranium dissolution (96%) in 40 days at 10% (w/v) pulp density (PD), 1.7 pH and 35{sup o}C. On increasing the pulp density from 10% to 20% under the same conditions, the biorecovery of uranium fell down from 96% to 82%. The higher uranium dissolution during bioleaching at 1.7 pH with the fine size particles (<45μm) can be correlated with increase in redox potential from 598 mV to 708 mV and the corresponding variation of Fe(III) ion concentration in 40 days. (author)

  10. Application of solution-mineral equilibrium chemistry to solution mining of uranium ores

    International Nuclear Information System (INIS)

    Riese, A.C.; Propp, C.J.

    1980-01-01

    Modern methods of uranium solution mining are typically accompanied by gains and losses of mass through reagent consumption by rock-forming minerals, with subsequent formation of clay minerals, gypsum, carbonates, and iron oxyhydroxides. A systematic approach to alleviate such problems involves the application of leach solutions that are in equilibrium with the host-rock minerals but in disequilibrium with the ore-forming minerals. This partial equilibrium can be approximated by solution-composition adjustments within the systems K 2 O-Al 2 O 3 SiO 2 -H 2 O and Na 2 O 3 -Al 2 O 3 SiO 2 -H 2 O. Uranium ore containing 0.15 percent U 3 O 8 from the Gulf Mineral Resources Corporation's Mariano Lake mine, the Smith Lake district of the Grants mineral belt, was collected for investigation. Presented are a theoretical evaluation of leachate data and an experimental treatment of the ore, which contained mainly K-feldspar, plagioclase feldspar, and quartz (with lesser amounts of micas, clay minerals, and organic carbonaceous material). Small-scale (less than or equal to 1 kg) column-leaching experiments were conducted to model the results of conventional leaching operations and to provide leachate solutions that could be compared with solutions calculated to be in equilibrium with the matrix minerals. Leach solutions employed include: 1) sulfuric acid, 2) sodium bicarbonate, and 3) sulfuric acid with 1.0 molal potassium chloride. The uranium concentrations in the sodium-bicarbonate leach solution and the acid-leach solution were about a gram per liter at the termination of the tests. However, the permeability of the ore in the acid leach was greatly reduced, owing to the formation of clay minerals. Uranium solubility in the leach column stabilized with the potassium-chloride solution was calculated from leachate compositions to be limited by the solubility of carnotite

  11. Biomineral processing of high apatite containing low-grade indian uranium ore

    International Nuclear Information System (INIS)

    Abhilash; Mehta, K.D.; Pandey, B.D.; Ray, L.; Tamrakar, P.K.

    2010-01-01

    Microbial species isolated from source mine water, primarily an enriched culture of Acidithiobacillus ferrooxidans was employed for bio-leaching of uranium from a low-grade apatite rich uranium ore of Narwapahar Mines, India while varying pH, pulp density (PD), particle size, etc. The ore (0.047% U_3O_8), though of Singhbhum area (richest deposit of uranium ores in India), due to presence of some refractory minerals and high apatite (5%) causes a maximum 78% recovery through conventional processing. Bioleaching experiments were carried out by varying pH at 35"oC using 20%(w/v) PD and <76μm size particles resulting in 83.5% and 78% uranium bio-recovery at 1.7 and 2.0 pH in 40 days as against maximum recovery of 46% and 41% metal in control experiments respectively. Finer size (<45μm) ore fractions exhibited higher uranium dissolution (96%) in 40 days at 10% (w/v) pulp density (PD), 1.7 pH and 35"oC. On increasing the pulp density from 10% to 20% under the same conditions, the biorecovery of uranium fell down from 96% to 82%. The higher uranium dissolution during bioleaching at 1.7 pH with the fine size particles (<45μm) can be correlated with increase in redox potential from 598 mV to 708 mV and the corresponding variation of Fe(III) ion concentration in 40 days. (author)

  12. Results of the radiological survey at the former ore storage site, Palmerton, Pennsylvania (PP001)

    International Nuclear Information System (INIS)

    Cottrell, W.D.; Quillen, J.L.; Crutcher, J.W.

    1990-12-01

    As part of the Formerly Utilized Sites Remedial Action Program (FUSRAP), the US Department of Energy (DOE) is implementing a radiological survey program to determine the radiological conditions at sites that were used by the department's predecessor agencies. The radiological survey discussed in this report for the former ore storage site in Palmerton, Pennsylvania, is part of the FUSRAP effort and was conducted at the request of DOE by members of the Measurement Applications and Development group of Oak Ridge National Laboratory (ORNL) in 1988. In 1953 and 1954 the Atomic Energy Commission (AEC) established an ore stockpile on the property of the New Jersey Zinc Corporation in Palmerton, Pennsylvania. Approximately 57 truckloads of ore (about 360 tons) were stored at this site and remained there until 1973, when the AEC initiated a clean-up program. The 1988 ORNL radiological survey included a gamma scan at the ground surface, gamma measurements at discrete locations at the surface and at 1 m above the surface, gamma logging of 80 auger holes, and collection of 161 surface and subsurface soil samples. Of these 161 soil samples, 98% were below DOE guidelines for 226 Ra concentration in soil. Interpretation of the data suggests small, isolated spots of residual ore. The data indicate that it is highly unlikely that an individual living or working on this site could receive a radiation dose approaching the 100 mrem annual limit. However, it is suggested that DOE evaluate potential exposures at this site to ensure compliance with their policy that all exposures to radiation are reduced to levels that are as low as reasonably achievable. 4 refs., 88 figs., 4 tabs

  13. A mineralogical investigation of a refractory gold ore, and of a sulphide concentrate and calcined tailing from that ore

    International Nuclear Information System (INIS)

    Ollila, J.T.

    1983-01-01

    This report covers an investigation into the manner of occurrence of gold in an old mine dump of calcined tailings at the Fairview Mine. Previous investigations had not revealed the whereabouts of the gold still present in this dump, which amounts to between 10 and 12p.p.m. In the present investigation, in which heavy-liquid separation was combined with X-ray, microscope, and electron-microprobe investigations, it was found that a significant proportion of the gold is adsorbed on carbon, and that a smaller proportion is present in pyrite that escaped complete calcination. An enigma is the occurrence of ferrosilicon, some of which contains gold. Although this study produced new information, a more detailed quantitative investigation is required in which an image analyser should be used to provide reliable quantitative data

  14. Iron isotope fractionation during hydrothermal ore deposition and alteration

    Science.gov (United States)

    Markl, Gregor; von Blanckenburg, Friedhelm; Wagner, Thomas

    2006-06-01

    Iron isotopes fractionate during hydrothermal processes. Therefore, the Fe isotope composition of ore-forming minerals characterizes either iron sources or fluid histories. The former potentially serves to distinguish between sedimentary, magmatic or metamorphic iron sources, and the latter allows the reconstruction of precipitation and redox processes. These processes take place during ore formation or alteration. The aim of this contribution is to investigate the suitability of this new isotope method as a probe of ore-related processes. For this purpose 51 samples of iron ores and iron mineral separates from the Schwarzwald region, southwest Germany, were analyzed for their iron isotope composition using multicollector ICP-MS. Further, the ore-forming and ore-altering processes were quantitatively modeled using reaction path calculations. The Schwarzwald mining district hosts mineralizations that formed discontinuously over almost 300 Ma of hydrothermal activity. Primary hematite, siderite and sulfides formed from mixing of meteoric fluids with deeper crustal brines. Later, these minerals were partly dissolved and oxidized, and secondary hematite, goethite and iron arsenates were precipitated. Two types of alteration products formed: (1) primary and high-temperature secondary Fe minerals formed between 120 and 300 °C, and (2) low-temperature secondary Fe minerals formed under supergene conditions (illustrates the potential of the new technique in deciphering ore formation and alteration processes. Isotope ratios are strongly dependent on and highly characteristic of fluid and precipitation histories. Therefore, they are less suitable to provide information on Fe sources. However, it will be possible to unravel the physico-chemical processes leading to the formation, dissolution and redeposition of ores in great detail.

  15. A finite difference model of the iron ore sinter process

    OpenAIRE

    Muller, J.; de Vries, T.L.; Dippenaar, B.A.; Vreugdenburg, J.C.

    2015-01-01

    Iron ore fines are agglomerated to produce sinter, which is an important feed material for blast furnaces worldwide. A model of the iron ore sintering process has been developed with the objective of being representative of the sinter pot test, the standard laboratory process in which the behaviour of specific sinter feed mixtures is evaluated. The model aims to predict sinter quality, including chemical quality and physical strength, as well as key sinter process performance parameters such ...

  16. Uranium mobilization from low-grade ore by cyanobacteria

    International Nuclear Information System (INIS)

    Lorenz, M.G.; Krumbein, W.E.

    1985-01-01

    Three cyanobacterial isolates (two LPP-B forms and one Anabaena or Nostoc species) from different environments could mobilize uranium from low-grade ores. After 80 days, up to 18% uranium had been extracted from coal and 51% from a carbonate rock by the filamentous cyanobacterium OL3, a LPP-B form. Low growth requirements with regard to light and temperature optima make this strain a possible candidate for leaching neutral and alkaline low-grade uranium ores. (orig.)

  17. Uranium mobilization from low-grade ore by cyanobacteria

    Energy Technology Data Exchange (ETDEWEB)

    Lorenz, M.G.; Krumbein, W.E.

    1985-04-01

    Three cyanobacterial isolates (two LPP-B forms and one Anabaena or Nostoc species) from different environments could mobilize uranium from low-grade ores. After 80 days, up to 18% uranium had been extracted from coal and 51% from a carbonate rock by the filamentous cyanobacterium OL3, a LPP-B form. Low growth requirements with regard to light and temperature optima make this strain a possible candidate for leaching neutral and alkaline low-grade uranium ores.

  18. Methods for the estimation of uranium ore reserves

    International Nuclear Information System (INIS)

    1985-01-01

    The Manual is designed mainly to provide assistance in uranium ore reserve estimation methods to mining engineers and geologists with limited experience in estimating reserves, especially to those working in developing countries. This Manual deals with the general principles of evaluation of metalliferous deposits but also takes into account the radioactivity of uranium ores. The methods presented have been generally accepted in the international uranium industry

  19. Radiotracer investigations of the flotation process in copper ore processing

    International Nuclear Information System (INIS)

    Petryka, L.; Przewlocki, K.

    1983-01-01

    Optimization of copper ore processing requires in particular the investigation of the flotation process. 64 Cu induced in natural ore by activation was used as a tracer. Detailed measurements were performed in an industrial flotation plant consisting of 14 cells. As a result the mean residence time of different grain size fractions of natural copper sulphide was determined for all parts of the flotation plant together with the efficiency of the flotation process. (author)

  20. Assessment of the contrast of rare metal ores

    International Nuclear Information System (INIS)

    Kuznetsova, O.V.

    1987-01-01

    The method of rapid assessment of useful component content on the basis of X-ray radiometric method of analysis of non-crushed ore lumps is presented. Using as an example rare metal deposits, linear dependence between logarithms of Nb 2 O 6 contents and the value of fragment separation index during radiometric separation is established. The use of the dependence ensures sufficient accuracy for the characteristic of rare metal ore content

  1. Rare earth mobility in hydrothermal ore-forming systems

    International Nuclear Information System (INIS)

    Cornell, D.H.; Schade, J.; Scheepers, R.; Watkeys, M.K.

    1988-01-01

    Rocks and ores which form by magmatic processes display a range of chondrite-normalised rare earth profiles. One REE (rare earth elements) profile feature which seems unrelated to magmatic processes is the birdwing profile, in which both heavy and light rare earths are enriched relative to the middle rare earths. Birdwing rare earth profiles are an easily identified geochemical anomaly. It is proposed that rare earth geochemistry could be applied in geochemical prospecting for ore formed by hydrothermal processes. 5 figs

  2. Polonium-210 in the environment around a radioactive waste disposal area and phosphate ore processing plant

    Energy Technology Data Exchange (ETDEWEB)

    Arthur, III, W J; Markham, O D

    1984-04-01

    Polonium-210 concentrations were determined for soil, vegetation and small mammal tissues collected at a solid radioactive waste disposal area, near a phosphate ore processing plant and at two rural areas in southeastern Idaho. Polonium concentrations in media sampled near the radioactive waste disposal facility were equal to or less than values from rural area samples, indicating that disposal of solid radioactive waste at the Idaho National Engineering Laboratory Site has not resulted in increased environmental levels of polonium. Concentrations of /sup 210/Po in soils, deer mice hide and carcass samples collected near the phosphate processing plant were statistically greater than the other sampling locations; however, the mean /sup 210/Po concentration in soils and small mammal tissues from sampling areas near the phosphate plant were only four and three times greater, respectively, than control values. No statistical difference was observed for /sup 210/Po concentrations in vegetation among any of the sampling locations.

  3. Recent trends in research and development work on the processing of uranium ore in South Africa

    International Nuclear Information System (INIS)

    James, H.E.

    1976-07-01

    The rapid increases in the price of gold and uranium in recent years have coincided with an unprecedented increase in working costs at South African gold mines. A re-examination of the existing flowsheets for the recovery of uranium, gold, and pyrite from Witwatersrand ores, in the light of these economic trends, has resulted in the identification of a number of profitable areas for research and development. The main topics under investigation in South Africa in the processing of uranium ore are the use of physical methods of concentration such as flotation, gravity concentration, and wet high-intensity magnetic separation; the wider adoption of the 'reverse leach', in which prior acid leaching for uranium improves the subsequent extraction of gold; the use of higher leaching temperatures and higher concentrations of ferric ion in the leach to increase the percentage of uranium extracted, including the production of ferric ion from recycled solutions; the application of pressure leaching to the recovery of uranium from low-grade ores and concentrates; the development of a continuous ion-exchange contactor capable of handling dilute slurries, so that simpler and cheaper techniques of solid-liquid separation can be used instead of the expensive filtration and clarification steps, and the improvement of instrumentation for the control of additions of sulphuric acid and manganese dioxide to the leach. A brief description is given of the essential features of the new or improved processing techniques under development that hold promise of full-scale application at existing or future uranium plants [af

  4. Recent trends in research and development work on the processing of uranium ore in South Africa

    International Nuclear Information System (INIS)

    James, H.E.

    1976-01-01

    The rapid increases in the price of gold and uranium in recent years have coincided with an unprecedented increase in working costs at South African gold mines. A re-examination of the existing flowsheets for the recovery of uranium, gold and pyrite from Witwatersrand ores, in the light of these economic trends, has resulted in the identification of a number of profitable areas for research and development. The main topics under investigation in South Africa in the processing of uranium ore are the use of physical methods of concentration such as flotation, gravity concentration and wet high-intensity magnetic separation; the wider adoption of the 'reverse leach', in which prior acid leaching for uranium improves the subsequent extraction of gold; the use of higher leaching temperatures and higher concentrations of ferric ion in the leach to increase the percentage of uranium extracted, including the production of ferric ion from recycled solutions; the application of pressure leaching to the recovery of uranium from low-grade ores and concentrates; the development of a continuous ion-exchange contactor capable of handling dilute slurries, so that simpler and cheaper techniques of solid/liquid separation can be used instead of the expensive filtration and clarification steps, and the improvement of instrumentation for the control of additions of sulphuric acid and manganese dioxide to the leach. A brief description is given of the essential features of the new or improved processing techniques under development that hold promise of full-scale application at existing or future uranium plants

  5. Analysis of copper-nickel ores by gamma-gamma method in ore enrichment works

    International Nuclear Information System (INIS)

    Bol'shakov, A.Yu.; Tovstenko, Yu.G.; Chinskij, E.B.; Eliseev, G.I.

    1973-01-01

    The paper presents experimental data on continuous gamma-gamma assay of copper-nickel ores on conveyor belts and of dry discrete samples of classifier overflow at the enrichment plants of the Pechenganikel' group. The relative errors are given of the results of comparison of two-hour rapid analyses and shift and 24-hour chemical analyses of classifier overflow samples with the figures for gamma-gamma assay. The factors affecting the accuracy of the latter technique are elucidated. Practical recommendations are given on the use of this technique at the above enrichment plants. (author)

  6. Flotation of uranium from uranium ores in Canada. Part 1

    International Nuclear Information System (INIS)

    Muthuswami, S.V.; Vigayan, S.; Woods, D.R.; Banerjee, S.

    1983-01-01

    About 150 flotation tests were done on Elliot Lake ore with 15 reagents as collectors in order to screen and choose an attractive collector for uranium flotation. Several variables were studied including pH, conditioning time and mode of collector addition. The tests were done in a Denver or Agitair subaeration cell. The particle size of the ore was kept at 85% below -325 mesh. Three reagents (Kelex 00, TOPO, and cupferron) were identified as having the most promise. The best results were obtained with cupferron, where 93-95% of the uranium was recovered in 25-30% of the mass of original ore. Radium in the tails varied between 5 and 30 pCi/g depending on the mass of uranium floated. Radium was recovered in proportion to uranium in the tests done at neutral pH. The preconcentration results obtained by flotation alone were comparable to those obtained using pyrite flotation and wet high-intensity magnetic separation of uranium. The consumption of cupferron was 4 kg/Mg ore for each flotation stage. This was 10-15 times larger than the collector usage in conventional oxide flotation. This scheme did not require other reagents as depressants, activators or modifiers. Reproducibility was good and similar recoveries were obtained with fresh or old ores, and with distilled or mine water. The selectivity of cupferron for uranium in the ore studied was outstanding

  7. Breakaway frictions of dynamic O-rings in mechanical seals

    Science.gov (United States)

    Lai, Tom; Kay, Peter

    1993-05-01

    Breakaway friction of a dynamic O-ring affects the mechanical seal's response to large axial shaft movement and face wear. However, little data exist to help designers. Therefore, a test rig was developed to measure breakaway friction. The research quantitatively shows the effects of lubrication with silicone grease and a change of surface finish. By using the Taguchi statistical experimental design method, the significance of test parameters was evaluated with a minimum number of tests. It was found that fluid pressure, dwell time, and O-ring percentage squeeze affect O-ring breakaway friction more than the O-ring cross sectional diameter and axial sliding speed within the range of values tested. The authors showed that breakaway friction increased linearly with pressure. However, O-rings made of different materials had significantly different increase rates, even if they had nominally the same durometer hardness. Breakaway friction also increased with logarithm of dwell time. Again, the increase rate depended strongly on the specific O-ring material tested. These observations led the authors to believe that the typical approach of generalizing data based on generic polymer type and durometer was inappropriate.

  8. Potential for cobalt recovery from lateritic ores in Europe

    Science.gov (United States)

    Herrington, R.

    2012-04-01

    Cobalt is one of the 'critical metals' identified under the EU Raw Materials Initiative. Annually the global mine production of cobalt is around 55,000 tonnes,with Europe's industries consuming around 30% of that figure. Currently Europe produces around 27 tonnes of cobalt from mines in Finland although new capacity is planned. Co-bearing nickel laterite ores being mined in Greece, Macedonia and Kosovo where the cobalt is currently not being recovered (ores have typical analyses of 0.055% Co and >1% Ni,). These ores are currently treated directly in pyrometallurgical plants to recover the contained nickel and this process means there is no separate cobalt product produced. Hydrometallurgical treatment of mineralogically suitable laterite ores can recover the cobalt; for example Cuba recovers 3,500 tonnes of cobalt from its laterite mining operations, which are of a similar scale to the current European operations. Implementation of hydrometallurgical techniques is in its infancy in Europe with one deposit in Turkey planning to use atmospheric heap leaching to recover nickel and copper from oxide-dominated ores. More widespread implementation of these methods to mineralogically suitable ore types could unlock the highly significant undeveloped resources (with metal contents >0.04% Co and >1% Ni), which have been defined throughout the Balkans eastwards into Turkey. At a conservative estimate, this region has the potential to supply up to 30% of the EU cobalt requirements.

  9. Automated microscopic characterization of metallic ores with image analysis: a key to improve ore processing. I: test of the methodology

    International Nuclear Information System (INIS)

    Berrezueta, E.; Castroviejo, R.

    2007-01-01

    Ore microscopy has traditionally been an important support to control ore processing, but the volume of present day processes is beyond the reach of human operators. Automation is therefore compulsory, but its development through digital image analysis, DIA, is limited by various problems, such as the similarity in reflectance values of some important ores, their anisotropism, and the performance of instruments and methods. The results presented show that automated identification and quantification by DIA are possible through multiband (RGB) determinations with a research 3CCD video camera on reflected light microscope. These results were obtained by systematic measurement of selected ores accounting for most of the industrial applications. Polarized light is avoided, so the effects of anisotropism can be neglected. Quality control at various stages and statistical analysis are important, as is the application of complementary criteria (e.g. metallogenetic). The sequential methodology is described and shown through practical examples. (Author)

  10. Automated microscopic characterization of metallic ores with image analysis: a key to improve ore processing. II: metallogenetic discriminating criteria

    International Nuclear Information System (INIS)

    Castroviejo, R.; Berrezueta, E.

    2009-01-01

    ore microscopy may furnish very important information for geo metallurgists, but todays needs for automation are difficult to meet with the optical microscope unless and adequate methodology is developed. Some limitations of the routine procedure, related to risks of mis identification caused by the spectral similarity of some ores, ask for complementary criteria. Defining ore deposit typologies and the corresponding assemblages guides the choice of species and limits the number. Comparison of the reflectance values of the ores in each mineral association defined shows that their automated identification is possible in most of the common occurrence. The number of species to be actually considered being greatly limited, performance is increased. The system is not intended to substitute for a mineralogist, but to enhance enormously his performance, while offering the industry an economic procedure to procedure a wealth of information which would not be possible with traditional methods, as the point counter. (Author) 33 refs.

  11. Comprehensive recovery of gold and base-metal sulfide minerals from a low-grade refractory ore

    Science.gov (United States)

    Li, Wen-juan; Liu, Shuang; Song, Yong-sheng; Wen, Jian-kang; Zhou, Gui-ying; Chen, Yong

    2016-12-01

    The comprehensive recovery of small amounts of valuable minerals such as gold and base-metal sulfide minerals from a low-grade refractory ore was investigated. The following treatment strategy was applied to a sample of this ore: gold flotation-gold concentrate leaching-lead and zinc flotation from the gold concentrate leaching residue. Closed-circuit trials of gold flotation yielded a gold concentrate that assayed at 40.23 g·t-1 Au with a recovery of 86.25%. The gold concentrate leaching rate was 98.76%. Two variants of lead-zinc flotation from the residue—preferential flotation of lead and zinc and bulk flotation of lead and zinc—were tested using the middling processing method. Foam from the reflotation was returned to the lead rougher flotation or lead-zinc bulk flotation, whereas middlings from reflotation were discarded. Sulfur concentrate was a byproduct. The combined strategy of flotation, leaching, and flotation is recommended for the treatment of this kind of ore.

  12. The role of metasomatism in the balance of halogens in ore-forming process at porphyry Cu-Mo deposits

    Science.gov (United States)

    Berzina, A. N.

    2009-04-01

    -sericite alteration zones. No Cl-bearing minerals were revealed in ore-metasomatic assemblages with the exception of extremely low Cl contents in secondary biotite and very rare low-Cl apatite in the early potassic alteration zone. In contrast, fluorine concentrates in chlorites and white micas; however, the F content in them is commonly lower than in dark minerals, especially in biotite from altered rocks. The highest F contents are typical of biotites related to potassic alteration (K-feldspar + biotite + quartz assemblage). For example, the F content at the Sora deposit ranges from 2.5-2.7 wt.% in the metasomatic biotite to 0.44-1.63 wt.% in the rock-forming biotite of host granitoids. At this deposit, fluorite is a major mineral of the ore-metasomatic assemblage. The Mo-rich Sora deposit drastically differs from the Cu-rich Erdenetiin Ovoo and Aksug deposits by extremely low (0.02-0.08 wt.%) Cl contents in dark minerals from all of the host rocks. The considerable quantity of chlorine released as a result of large-scale propylitic and phyllic alteration from halogen-bearing dark minerals at Cu-rich deposits considerably affected the general Cl budget in the ore-metasomatic system. This could significantly promote the generation of Cl-rich (up to 50-70 wt.% NaCl-equiv.) ore-forming solutions at such deposits. At the Sora deposit characterized by less concentrated ore-bearing solutions (12-20 wt.% NaCl-equiv.), the metasomatic alteration of host rocks was not accompanied by an appreciable removal of Cl. At the studied deposits, huge volumes of enclosing rocks were involved in metasomatism. The large amounts of halogens released during the metasomatic alteration of host rocks might have significantly influenced the balance of volatiles in the ore forming system, including the increase in the salinity of hydrothermal solutions.

  13. Expansion of the ore treatment plant at Ranger Uranium Mines at Jabiru, NT Australia

    International Nuclear Information System (INIS)

    Nice, R.W.; Banaczkowski, M.

    2000-01-01

    The Ranger Uranium Mine commenced processing ore in 1980. The original plant designed by the joint venture between Davy and Wright Engineers had been designed to treat 1.3 Mtpa of ore to produce 3500 tpa of U 3 O 8 concentrates. The plant operated successfully through good and bad years until the 1995 when the owners of Energy Resources of Australia, North Ltd. (70%) decided that there was a market opening to allow expansion of the treatment plant such that it would produce 6000 tpa of concentrate.The desire to produce more concentrates was market driven but the change from the mine Ranger 1 to a new pit Ranger 3 also necessitated the inclusion of the ability to treat more ore. This involved the installation of more grinding and CCD washing capacity. There were some other changes that were to be included into the expansion to overcome operating deficiencies, reduce operating costs and to generally make the operation easier.The Australian engineering company, Kvaerner Davy, was commissioned to provide the EPCM services to the clients, North and the Ranger Operation Group. North Technical Services managed the Project with considerable input from the site operating and maintenance personnel. The site operating personnel commissioned the plant and are successfully operating it at the time of the preparation of this paper. The first part of this paper presents the basic process related activities required to provide the expanded facilities. This includes the flowsheet modifications, equipment changes and new equipment procured. Additionally, a discussion is given regarding the P and ID changes, the piping modifications and the means to install the expanded facilities with a minimum of interruption to the continuing plant operation. A second part of the paper details some of the experiences gained while constructing the expansion and commissioning and operating the expanded plant. (author)

  14. Applicability of attrition of iron ore in floating; Aplicabilidade da atricao do minerio de ferro na flotacao

    Energy Technology Data Exchange (ETDEWEB)

    Fortes, Fabiana Fonseca

    2010-07-01

    The aim of this study is to investigate the possibility to increase metal recovery in the flotation of iron ore with the implementation of a stage of scrubbing followed by dispersion. The minerals in question stems from two mines located in the western portion of the Iron Quadrangle and differ mainly with respect to the percentage of hematite and porous and the presence of aggregated masses. These characteristics were compared to those of other minerals that have succeeded with the adoption of this technique. Tests were conducted at bench scale scrubbing, desliming and concentration by flotation with the blend of ore from both mines. Were varied stirring time and pH. The chemical results of desliming and flotation products in the different conditions were compared. The presence of porous hematite is relevant in a mine, mainly due to the occurrence of earthy goethite, alumina carrier of the contaminant. The step desliming is insufficient for the removal of harmful sludge flotation. Laboratory experiments showed that the scrubbing of the pulp of iron ore of Minas de Capitao do Mato and Tamandua, agitated for 10 minutes followed by desliming amid scattered, promotes increased metal recovery by about 17% and increases the selectivity of 40 % compared to the results of the scrubbing and without dispersion. The scrubbing of hematite ore followed by desliming amid scattered can bring gains in improving the quality of pellet feed fine if deployed industrially. (author)

  15. A statistical approach to the experimental design of the sulfuric acid leaching of gold-copper ore

    Directory of Open Access Journals (Sweden)

    Mendes F.D.

    2003-01-01

    Full Text Available The high grade of copper in the Igarapé Bahia (Brazil gold-copper ore prevents the direct application of the classic cyanidation process. Copper oxides and sulfides react with cyanides in solution, causing a high consumption of leach reagent and thereby raising processing costs and decreasing recovery of gold. Studies have showm that a feasible route for this ore would be a pretreatment for copper minerals removal prior to the cyanidation stage. The goal of this experimental work was to study the experimental conditions required for copper removal from Igarapé Bahia gold-copper ore by sulfuric acid leaching by applying a statistical approach to the experimental design. By using the Plackett Burman method, it was possible to select the variables that had the largest influence on the percentage of copper extracted at the sulfuric acid leaching stage. These were temperature of leach solution, stirring speed, concentration of sulfuric acid in the leach solution and particle size of the ore. The influence of the individual effects of these variables and their interactions on the experimental response were analyzed by applying the replicated full factorial design method. Finally, the selected variables were optimized by the ascending path statistical method, which determined the best experimental conditions for leaching to achieve the highest percentage of copper extracted. Using the optimized conditions, the best leaching results showed a copper extraction of 75.5%.

  16. Optimization of gold ore Sumbawa separation using gravity method: Shaking table

    Science.gov (United States)

    Ferdana, Achmad Dhaefi; Petrus, Himawan Tri Bayu Murti; Bendiyasa, I. Made; Prijambada, Irfan Dwidya; Hamada, Fumio; Sachiko, Takahi

    2018-04-01

    Most of artisanal small gold mining in Indonesia has been using amalgamation method, which caused negative impact to the environment around ore processing area due to the usage of mercury. One of the more environmental-friendly method for gold processing is gravity method. Shaking table is one of separation equipment of gravity method used to increase concentrate based on difference of specific gravity. The optimum concentration result is influenced by several variables, such as rotational speed shaking, particle size and deck slope. In this research, the range of rotational speed shaking was between 100 rpm and 200 rpm, the particle size was between -100 + 200 mesh and -200 + 300 mesh and deck slope was between 3° and 7°. Gold concentration in concentrate was measured by EDX. The result shows that the optimum condition is obtained at a shaking speed of 200 rpm, with a slope of 7° and particle size of -100 + 200 mesh.

  17. Fast quantification of uranium ores by X-ray fluorescence analysis

    International Nuclear Information System (INIS)

    Morales, E.; De la Roca, W.

    1988-09-01

    A fast and reliable method for batch quantification of uranium in mineral ores is described. It is based on the verification of the homogeneity of the samples through measuring the ratio of coherent and incoherent dispersion. A few samples, 6 or more, are taken from the whole batch and analyzed by fundamental parameters method. A calibration curve using Lancance-Traill or Lucas-Tooth algorithms is constructed in order that the absorption and enhancement effects could be corrected. Simple interpolation of the intensities of the remaining samples gives their concentration. (author)

  18. Research on regimes of limonite ore hyrdotransport for the conditions of Perdo Soto Alba plant

    Directory of Open Access Journals (Sweden)

    Рауль Искьердо Пупо

    2017-04-01

    Full Text Available The paper examines regular flow patterns of high-concentrated limonite pulp with significant content of finest grains. Engineering procedures have been developed to calculate basic parameters of limonite ore hydrotransport in turbulent and structured regimes. Trustworthiness of scientific statements, conclusions and recommendations is justified by theoretical research, establishment of analytical dependences, results of laboratory and industrial experiments. Practical regularities of behavior have been identified for the coefficient of hydraulic resistance, depending on pulp density in the range 35-45 % in case of pulp flow in structured regime, as well as regularity of pressure losses in case of pulp flow in horizontal and inclined pipelines in turbulent regime.

  19. Investigation of an egyptian phosphate ore sample by neutron activation analysis technique

    International Nuclear Information System (INIS)

    Eissa, E.A.; Aly, R.A.; Rofail, N.B.; Hassan, A.M.

    1995-01-01

    A domestic phosphate ore sample has been analysed by means of prompt and delayed gamma-ray spectrometry following the activation by thermal neutron capture technique. The rabbit pneumatic transfer system (RPTS), long irradiation facility and two Pu/Be (2,5 Ci each) neutron sources set-Pu for prompt (n,gamma) were applied. The high purity germanium (HPGe) gamma-ray spectrometer with a personal computer analyzer (PCA) system were used for spectrum measurements. Programmes on the VAX computer were utilized for estimating the elemental concentrations of 22 out of 36 elements identified in this work. 2 tabs

  20. Determination of uranium content in phosphate ores using different measurement techniques

    Directory of Open Access Journals (Sweden)

    Mohammad A. Al-Eshaikh

    2016-01-01

    Full Text Available The most important unconventional source of uranium is found in phosphate deposits; unfortunately, nowadays its exploitation is limited by economic constraints. The uranium concentrations in phosphate ores in the world vary regionally and most countries with large phosphate deposits have either plant in operation to extract uranium or are at the stage of pilot extraction plants. The aim of this investigation is to evaluate uranium content in the Saudi phosphate ores for, at least, two reasons: firstly, upgrading the phosphate quality by removing the uranium content in order to reduce the radioactivity in the fertilizer products. Secondly, getting benefit from the extracted uranium for its domestic use as a fuel in nuclear power and desalination plants. The results of this study show that the uranium concentration in Saudi phosphate rocks is relatively low (less than 100 ppm, which is not economically encouraging for its direct extraction. However, its extraction as a byproduct from the phosphoric acid, which will have higher concentration could be quite promising and worth exploiting.

  1. Study in pilot plant of the Itataia phosphoro-uraniferous ore - CE (Brazil)

    International Nuclear Information System (INIS)

    Reis Junior, J.B.; Aquino, J.A. de; Oliveira Luz, I.L. de.

    1987-01-01

    Pilot plant data have been obtained for the physical treatment studies of the Itataia, phosphoro-uraniferous ore body located in the state of Ceara-Brazil. Due to the presence of the silic-carbonated gangue, which turns the ore complex, the pilot plant operation comprised 1200 hours. From the results obtained, it was possible to stablish a basic flowsheet for the concentration process. Such process includes a grinding step followed by a cyclone disliming (d 50 =10μm). The cyclone underflow feeds the flotation step. The conventional flotation process, which envolves the direct phosphate flotation followed by cleaning steps, was not efficient due to the presence of the carbonated gangue. In fact, the presence of silicates and carbonates in the gangue required that the flotation would be carried out in two steps. The silicated gangue is eliminated in the first flotation and a phosphate concentrate with significant amount of carbonates is obtained. This concentrate is fed to the second flotation step, termed reverse flotation, where the calcite is floated and the apatite is depressed. (Author) [pt

  2. Study in pilot plant of the Itataia phosphoro-uraniferous ore (CE,Brazil)

    International Nuclear Information System (INIS)

    Reis Junior, J.B.; Aquino, J.A. de; Oliveira Luz, I.L. de

    1985-01-01

    Pilot plant data have been obtained for the physical treatment studies of the Itataia, phosphoro-uraniferous ore body located in the state of Ceara-Brazil. Due to the presence of the silic-carbonated gangue, which turns the ore complex, the pilot plant operation comprised 1200 hours. From the results obtained, it was possible to establish a basic flowsheet for the concentration process. Such process includes a grinding step (-65) followed by a cyclone disliming (d50 = 10μ). The cyclone underflow feeds the flotation step. The conventional flotation process, which envolves the direct phosphate flotation followed by cleaning steps, was not efficient due to the presence of the carbonated gangue. In fact, the presence of silicates and carbonates in the gangue required that the flotation would be carried out in two steps. The silicated gangue is eliminated in the first flotation and a phosphate concentrate with significant amount of carbonates is obtained. This concentrate is fed to the second flotation step, termed reverse flotation, where the calcite is floated and the apatite is depressed. (Author) [pt

  3. Titrimetric determination of uranium in low-grade ores by the ferrous ion-phosphoric acid reduction method

    International Nuclear Information System (INIS)

    Hitchen, A.; Zechanowitsch, G.

    1980-01-01

    The modification and extension of the U.S.A.E.C. ferrous ion-phosphoric acid reduction method for the determination of uranium in high-grade or relatively pure material to a method for the determination of uranium with a high accuracy and precision, in ores containing 0.004 to 7% U is described. It is simple, rapid and requires no prior separations from elements that, in other methods, frequently interfere. For sample materials having very high concentrations of interfering elements, a prior concentration step using extraction with tri-n-octylphosphine oxide is described, but it is shown that, for most low-grade ores, this step is unnecessary. (author)

  4. Microbial Beneficiation of Salem Iron Ore Using Penicillium purpurogenum

    Science.gov (United States)

    Mishra, M.; Pradhan, M.; Sukla, L. B.; Mishra, B. K.

    2011-02-01

    High alumina and silica content in the iron ore affects coke rate, reducibility, and productivity in a blast furnace. Iron ore is being beneficiated all around the world to meet the quality requirement of iron and steel industries. Choosing a beneficiation treatment depends on the nature of the gangue present and its association with the ore structure. The advanced physicochemical methods used for the beneficiation of iron ore are generally unfriendly to the environment. Biobeneficiation is considered to be ecofriendly, promising, and revolutionary solutions to these problems. A characterization study of Salem iron ore indicates that the major iron-bearing minerals are hematite, magnetite, and goethite. Samples on average contains (pct) Fe2O3-84.40, Fe (total)-59.02, Al2O3-7.18, and SiO2-7.53. Penicillium purpurogenum (MTCC 7356) was used for the experiment . It removed 35.22 pct alumina and 39.41 pct silica in 30 days in a shake flask at 10 pct pulp density, 308 K (35 °C), and 150 rpm. In a bioreactor experiment at 2 kg scale using the same organism, it removed 23.33 pct alumina and 30.54 pct silica in 30 days at 300 rpm agitation and 2 to 3 l/min aeration. Alumina and silica dissolution follow the shrinking core model for both shake flask and bioreactor experiments.

  5. Utilisation of iron ore tailings as aggregates in concrete

    Directory of Open Access Journals (Sweden)

    Francis Atta Kuranchie

    2015-12-01

    Full Text Available Sustainable handling of iron ore tailings is of prime concern to all stakeholders who are into iron ore mining. This study seeks to add value to the tailings by utilising them as a replacement for aggregates in concrete. A concrete mix of grade 40 MPa was prepared in the laboratory with water–cement ratio of 0.5. The concrete were cured for 1, 2, 3, 7, 14 and 28 days. The properties of the concrete such as workability, durability, density, compressive strength and indirect tensile strength were tested. A controlled mix of concrete was also prepared in similar way using conventional materials and the results were compared with the tailings concrete. It was found that the iron ore tailings may be utilised for complete replacement for conventional aggregates in concrete. The iron ore tailings aggregates concrete exhibited a good mechanical strength and even in the case of compressive strength, there was an improvement of 11.56% over conventional aggregates concrete. The indirect tensile strength did not improve against the control mix due high content of fines in the tailings aggregates but showed 4.8% improvement compared with the previous study where the conventional fine aggregates was partially replaced by 20% with iron ore tailings.

  6. Novel Binders and Methods for Agglomeration of Ore

    Energy Technology Data Exchange (ETDEWEB)

    S. K. Kawatra; T. C. Eisele; J. A. Gurtler; K. Lewandowski

    2005-09-30

    Many metal extraction operations, such as leaching of copper, leaching of precious metals, and reduction of metal oxides to metal in high-temperature furnaces, require agglomeration of ore to ensure that reactive liquids or gases are evenly distributed throughout the ore being processed. Agglomeration of ore into coarse, porous masses achieves this even distribution of fluids by preventing fine particles from migrating and clogging the spaces and channels between the larger ore particles. Binders are critically necessary to produce agglomerates that will not break down during processing. However, for many important metal extraction processes there are no binders known that will work satisfactorily at a reasonable cost. A primary example of this is copper heap leaching, where there are no binders currently encountered in this acidic environment process. As a result, operators of many facilities see a large loss of process efficiency due to their inability to take advantage of agglomeration. The large quantities of ore that must be handled in metal extraction processes also means that the binder must be inexpensive and useful at low dosages to be economical. The acid-resistant binders and agglomeration procedures developed in this project will also be adapted for use in improving the energy efficiency and performance of a broad range of mineral agglomeration applications, particularly heap leaching. The active involvement of our industrial partners will help to ensure rapid commercialization of any agglomeration technologies developed by this project.

  7. Technique for in situ leach simulation of uranium ores

    International Nuclear Information System (INIS)

    Grant, D.C.; Seidel, D.C.; Nichols, I.L.

    1985-01-01

    In situ uranium mining offers the advantages of minimal environmental disturbance, low capital and operating costs, and reduced mining development time. It is becoming an increasingly attractive mining method for the recovery of uranium from secondary ore deposits. In order to better understand the process, a laboratory technique was developed and used to study and simulate both the chemical and physical phenomena occurring in ore bodies during in situ leaching. The laboratory simulation technique has been used to determine effects of leaching variables on permeability, uranium recovery, and post-leach aquifer restoration. This report describes the simulation system and testing procedure in sufficient detail to allow the construction of the system, and to perform the desired leaching tests. With construction of such a system, in situ leaching of a given ore using various leach conditions can be evaluated relatively rapidly in the laboratory. Not only could optimum leach conditions be selected for existing ore bodies, but also exploitation of new ore bodies could be accelerated. 8 references, 8 figures, 2 tables

  8. Novel Binders and Methods for Agglomeration of Ore

    Energy Technology Data Exchange (ETDEWEB)

    S. K. Kawatra; T. C. Eisele; K. A. Lewandowski; J. A. Gurtler

    2006-03-31

    Many metal extraction operations, such as leaching of copper, leaching of precious metals, and reduction of metal oxides to metal in high-temperature furnaces, require agglomeration of ore to ensure that reactive liquids or gases are evenly distributed throughout the ore being processed. Agglomeration of ore into coarse, porous masses achieves this even distribution of fluids by preventing fine particles from migrating and clogging the spaces and channels between the larger ore particles. Binders are critically necessary to produce agglomerates that will not break down during processing. However, for many important metal extraction processes there are no binders known that will work satisfactorily at a reasonable cost. A primary example of this is copper heap leaching, where there are no binders currently encountered in this acidic environment process. As a result, operators of many facilities see a large loss of process efficiency due to their inability to take advantage of agglomeration. The large quantities of ore that must be handled in metal extraction processes also means that the binder must be inexpensive and useful at low dosages to be economical. The acid-resistant binders and agglomeration procedures developed in this project will also be adapted for use in improving the energy efficiency and performance of a broad range of mineral agglomeration applications, particularly heap leaching. The active involvement of our industrial partners will help to ensure rapid commercialization of any agglomeration technologies developed by this project.

  9. NOVEL BINDERS AND METHODS FOR AGGLOMERATION OF ORE

    Energy Technology Data Exchange (ETDEWEB)

    S.K. Kawatra; T.C. Eisele; J.A. Gurtler; C.A. Hardison; K. Lewandowski

    2004-04-01

    Many metal extraction operations, such as leaching of copper, leaching of precious metals, and reduction of metal oxides to metal in high-temperature furnaces, require agglomeration of ore to ensure that reactive liquids or gases are evenly distributed throughout the ore being processed. Agglomeration of ore into coarse, porous masses achieves this even distribution of fluids by preventing fine particles from migrating and clogging the spaces and channels between the larger ore particles. Binders are critically necessary to produce agglomerates that will not break down during processing. However, for many important metal extraction processes there are no binders known that will work satisfactorily. Primary examples of this are copper heap leaching, where there are no binders that will work in the acidic environment encountered in this process, and advanced ironmaking processes, where binders must function satisfactorily over an extraordinarily large range of temperatures (from room temperature up to over 1200 C). As a result, operators of many facilities see a large loss of process efficiency due to their inability to take advantage of agglomeration. The large quantities of ore that must be handled in metal extraction processes also means that the binder must be inexpensive and useful at low dosages to be economical. The acid-resistant binders and agglomeration procedures developed in this project will also be adapted for use in improving the energy efficiency and performance of a broad range of mineral agglomeration applications, particularly heap leaching and advanced primary ironmaking.

  10. Evaluation of radon and their daughters concentration and estimative of effective dose in a waste deposits at the ore treatment unity of INB/Pocos de Caldas, Brazil; Avaliacao da concentracao de radonio e seus filhos e estimativa de dose efetiva em um deposito de rejeitos na unidade de tratamento de minerios da INB/Caldas

    Energy Technology Data Exchange (ETDEWEB)

    Dantas, Marcelino V.A.; Garcia Filho, Oswaldo; Antunes, Marcos M.; Junior, Joao V.S.; Py Junior, Delcy A., E-mail: marcelino@inb.gov.b, E-mail: wspereira@inb.gov.b, E-mail: ogarcia@inb.gov.b, E-mail: antunes@inb.gov.b, E-mail: Joao@inb.gov.b, E-mail: delcy@inb.gov.b [Industrias Nucleares do Brasil (UTM/INB), Caldas, MG (Brazil). Unidade de Tratamento de Minerios; Pereira, Wagner S. [Industrias Nucleares do Brasil (UTM/INB), Caldas, MG (Brazil). Unidade de Tratamento de Minerios; Universidade Federal Fluminense (IB/UFF), Niteroi, RJ (Brazil). Inst. de Biologia. Lab. de Radiobiologia e Radiometria Pedro Lopes dos Santos

    2011-10-26

    This paper conducts a surveillance of radon and their short half-life daughters gas concentration, inside the warehouse due to these gas inhalation. The results showed that the average concentration inside the warehouse ix approximately 700 Bq/m{sup 3} and the effective dose of an IOE, related to that concentration would be 5.0 mSv/year, therefore being 4 times lower than the established limit of 20 mSv/year

  11. Potential of heavy minerals in the Valenca-Itacare, Bahia (Brazil) region - Sampling characterization and ore processing

    International Nuclear Information System (INIS)

    Noguti, I.; Feitosa, J.A.

    1989-01-01

    Important heavy minerals deposits were discovered by CBPM in the townships of Nilo Pecanha and Marau, state of Bahia. Ore dressing tests were conducted at CETEC and the results indicate a good potential. Tests were carried out with the Humphreys spiral, with magnetic and electro-static separators were yielding concentrates of ilmenite with 56.0% TiO 2 and Zircon with 65.0% ZrO 2 . (author) [pt

  12. Gamma ray fluorescence for in situ evaluation of ore in Witwatersrand gold mines

    International Nuclear Information System (INIS)

    Rolle, R.

    1979-01-01

    A system for quantitative in situ evaluation of ore in Witwatersrand gold mines was researched and subsequently developed. The principle of measurement is based on the excitation of gold K X-rays in rock face samples by the 88 keV gamma radiation from a Cadmium-109 radioisotope source. The X-rays and scattered radiation from the rock matrix are detected by a hyperpure germanium detector cooled by liquid nitrogen in a portable probe. In the fluorescence spectrum the intensity ratio of the gold Kβ peaks to their immediate scattered background is evaluated and quantitatively converted in the portable analyser to area concentration units. All aspects of the physical and instrumental measurement had to be investigated to arrive at a system capable of quantitative evaluation of trace concentrations in stope face ore samples. The parameters of spectrum evaluation were investigated from fundamental principles to allow quantitative assessment of different methods of peak evaluation for optimization of the method as a whole. The basic concepts of random signal processing times were developed together with new concepts of pileup parameters to allow a quantitative description of the data acquisition rate of a complete analog pulse processing system. With this foundation a practical measuring geometry and optimum values for signal processing time parameters, for detector size and for discriminator positions for spectrum evaluation could be determined. Parallel with the derivation of optimum measurement parameters went the development of instruments, their field testing and appraisal of the method. The development of the gamma ray fluorescence method has shown the potential of the method to serve as an ore valuation tool and to assist in the geological identification of strata in Witwatersrand gold mines

  13. Dynamics of leaching a uniformly fissured ore body

    International Nuclear Information System (INIS)

    Ignatov, A.A.; Proskurin, S.A.

    1987-01-01

    Mathematical simulation was used to study the dynamics of mass transfer during the percolation of a reagent solution through a packing of coarse ore particles. The uniformly fissured ore body was represented by a cubic packing of spherical particles of constant radius, formed from a chemically inert silicate cement with a uniformly distributed soluble mineral component. The rate of percolation of the reagent through the packing was constant. The proposed model can be used to find the conditions for underground hydrodynamic leaching. The rate of non-catalytic solid-liquid reaction was deduced on the basis of both the kinetics of dissolution of the mineral component of the ore and the rate of diffusion of the dissolved substance

  14. Complex sulphide-barite ore leaching in ferric chloride solution

    Directory of Open Access Journals (Sweden)

    Miroslav Sokić

    2016-06-01

    Full Text Available The results of research on the leaching process of complex sulphide-barite ore were presented in this paper. The leaching process was carried out in a laboratory autoclave by ferric chloride solution. Considering that those minerals are represented in complex structural-textural relationships, it is not possible to extract lead, zinc and copper minerals from ore by flotation methods. The obtained results confirmed possibility of the ore processing directly, by chemical methods. The effect of temperature, time and oxygen partial pressure on the lead, zinc and copper dissolution was studied. The maximal leaching degree was achieved at 100 °C and amount of 91.5 % for Pb, 96.1 % for Zn and 60.7 % for Cu. Leaching at temperatures above 100 °C is impractical.

  15. Ore-processing technology and the uranium supply outlook

    International Nuclear Information System (INIS)

    James, H.E.; Simonsen, H.A.

    1978-01-01

    The subject is covered in sections, as follows: the resource base (uranium content of rocks, regional distribution of Western World uranium); ore types (distribution of Western World uranium, by ore types, response to ore-processing); constraints on expansion in traditional uranium areas (defined for this paper as the sandstone deposits of the U.S.A. and the quartz-pebble conglomerates of the Witwatersrand and Elliot Bay areas, all other deposits being referred to as new uranium areas). Sections then follow dealing in detail with the processing of deposits in U.S.A., South Africa, Canada, Niger, Australia, South West Africa, Greenland. More general sections follow on: shale, lignite and coal deposits, calcrete deposits. Finally, there are sections on: uranium as a by-product; uranium from very low-grade resources; constraints on expansion rate for production facilities. (U.K.)

  16. Aluminum chloride restoration of in situ leached uranium ores

    International Nuclear Information System (INIS)

    Grant, D.C.; Burgman, M.A.

    1982-01-01

    During in situ uranium mining using ammonium bicarbonate lixiviant, the ammonium exchanges with cations on the ore's clay. After mining is complete, the ammonium may desorb into post-leach ground water. For the particular ore studied, other chemicals (i.e., uranium and selenium) which are mobilized during the leach process, have also been found in the post-leach ground water. Laboratory column tests, used to simulate the leaching process, have shown that aluminum chloride can rapidly remove ammonium from the ore and thus greatly reduce the subsequent ammonium leakage level into ground water. The aluminum chloride has also been found to reduce the leakage levels of uranium and selenium. In addition, the aluminum chloride treatment produces a rapid improvement in permeability

  17. Chloride pyrometallurgy of uranium ore. 1. Chlorination of phosphate ore using solid or gas chlorinating agent and carbon

    International Nuclear Information System (INIS)

    Taki, Tomihiro; Komoto, Shigetoshi; Otomura, Keiichiro; Takenaka, Toshihide; Sato, Nobuaki; Fujino, Takeo.

    1995-01-01

    A thermodynamical and pyrometallurgical study to recover uranium from the phosphate ores was undertaken using the chloride volatilization method. Iron was chlorinated with solid chlorinating agents such as NaCl and CaCl 2 in combination with activated carbon, which will be used for removing this element from the ore, but uranium was not. On the other hand, the chlorination using Cl 2 gas and activated carbon gave a good result at 1,223 K. Not only uranium but also iron, phosphorus, aluminum and silicon were found to form volatile chlorides which vaporized out of the ore, while calcium remained in the ore as non-volatile CaCl 2 . The chlorination condition was studied as functions of temperature, reaction time and carbon content. The volatilization ratio of uranium around 95% was obtained by heating the mixture of the ore and activated carbon (35 wt%) in a mixed gas flow of Cl 2 (200 ml/min) and N 2 (200 ml/min) at 1,223 K for 120 min. (author)

  18. [Assessment of Soil Fluorine Pollution in Jinhua Fluorite Ore Areas].

    Science.gov (United States)

    Ye, Qun-feng; Zhou, Xiao-ling

    2015-07-01

    The contents of. soil total fluorine (TF) and water-soluble fluorine (WF) were measured in fluorite ore areas located in Jinhua City. The single factor index, geoaccumulation index and health risk assessment were used to evaluate fluorine pollution in soil in four fluorite ore areas and one non-ore area, respectively. The results showed that the TF contents in soils were 28. 36-56 052. 39 mg.kg-1 with an arithmetic mean value of 8 325.90 mg.kg-1, a geometric mean of 1 555. 94 mg.kg-1, and a median of 812. 98 mg.kg-1. The variation coefficient of TF was 172. 07% . The soil WF contents ranged from 0. 83 to 74. 63 mg.kg-1 with an arithmetic mean value of 16. 94 mg.kg-1, a geometric mean of 10. 59 mg.kg-1, and a median of 10. 17 mg.kg-1. The variation coefficient of WF was 100. 10%. The soil TF and WF contents were far higher than the national average level of the local fluorine epidemic occurrence area. The fluoride pollution in soil was significantly affected by human factors. Soil fluorine pollution in Yangjia, Lengshuikeng and Huajie fluorite ore areas was the most serious, followed by Daren fluorite ore area, and in non-ore area there was almost no fluorine pollution. Oral ingestion of soils was the main exposure route. Sensitivity analysis of model parameters showed that children's weight exerted the largest influence over hazard quotient. Furthermore, a significant positive correlation was found among the three kinds of evaluation methods.

  19. Challenges facing the North American iron ore industry

    Science.gov (United States)

    Jorgenson, J.D.

    2005-01-01

    During the 20th century, the iron ore mining industries of Canada and the United States passed through several periods of transformation. The beginning of the 21st century has seen yet another period of transformation, with the economic failure of a number of steel companies, the acquisition of their facilities by more viable steelmakers, and the consolidation of control within the North American iron ore industry. Changes in Canadian and United States iron ore production and the market control structure involved are analysed. The consolidation of ownership, formation of foreign joint ventures within Nordi America, planned divestitures of upstream activities by steelmakers, and industry changes made to ensure availability of feedstocks will be reviewed. The ttaditional isolation of the Canadian and United States iron ore operations and their strong linkage to downstream steel production will be discussed in the context of a changing global economy. Management-labour conflicts that have taken place and agreements made during 2000 through 2004 will be discussed in the context of the economic environment leading up to these agreements. Cooperative agreements between competing Canadian and United States companies to resolve client needs in processing and blending will be examined. A joint industry-government project designed to use new technology to produce direct reduced iron nuggets of 96 - 98 per cent iron content using non-coking coals will also be assessed. Changes in iron ore transportation methods, ownership and infrastructure will be reviewed for both rail and inland waterway transport between Canadian and United States companies. A brief analysis of social and environmental issues relating to sustainable development of the Canadian-United States iron ore industry will be included.

  20. Novel Binders and Methods for Agglomeration of Ore

    Energy Technology Data Exchange (ETDEWEB)

    S. K. Kawatra; T. C. Eisele; K. A. Lewandowski; J. A. Gurtler

    2006-12-31

    Many metal extraction operations, such as leaching of copper, leaching of precious metals, and reduction of metal oxides to metal in high-temperature furnaces, require agglomeration of ore to ensure that reactive liquids or gases are evenly distributed throughout the ore being processed. Agglomeration of ore into coarse, porous masses achieves this even distribution of fluids by preventing fine particles from migrating and clogging the spaces and channels between the larger ore particles. Binders are critically necessary to produce agglomerates that will not break down during processing. However, for many important metal extraction processes there are no binders known that will work satisfactorily. Primary examples of this are copper heap leaching, where there are no binders that will work in the acidic environment encountered in this process, and advanced ironmaking processes, where binders must function satisfactorily over an extraordinarily large range of temperatures (from room temperature up to over 1200 C). As a result, operators of many facilities see a large loss of process efficiency due to their inability to take advantage of agglomeration. The large quantities of ore that must be handled in metal extraction processes also means that the binder must be inexpensive and useful at low dosages to be economical. The acid-resistant binders and agglomeration procedures developed in this project will also be adapted for use in improving the energy efficiency and performance of a broad range of mineral agglomeration applications, particularly heap leaching and advanced primary ironmaking. This project has identified several acid-resistant binders and agglomeration procedures that can be used for improving the energy efficiency of heap leaching, by preventing the ''ponding'' and ''channeling'' effects that currently cause reduced recovery and extended leaching cycle times. Methods have also been developed for iron ore

  1. Control of Rock Mechanics in Underground Ore Mining

    Science.gov (United States)

    Golik, V. I.; Efremenkov, A. B.

    2017-07-01

    Performance indicators in underground mining of thick iron fields can be insufficient since geo-mechanic specifics of ore-hosting fields might be considered inadequately, as a consequence, critical deformations and even earth’s surface destruction are possible, lowering the indicators of full subsurface use, this way. The reason for it is the available approach to estimating the performance of mining according to ore excavation costs, without assessing losses of valuable components and damage to the environment. The experimental approach to the problem is based on a combination of methods to justify technical capability and performance of mining technology improvement with regard to geomechanical factors. The main idea of decisions to be taken is turning geo-materials into the condition of triaxial compression via developing the support constructions of blocked up structural rock block. The study was carried out according to an integrated approach based on the analysis of concepts, field observations, and simulation with the photo-elastic materials in conditions of North Caucasus deposits. A database containing information on the deposit can be developed with the help of industrial experiments and performance indicators of the field can be also improved using the ability of ore-hosting fields to develop support constructions, keeping the geo-mechanical stability of the system at lower cost, avoiding ore contamination at the processing stage. The proposed model is a specific one because an adjustment coefficient of natural and anthropogenic stresses is used and can be adopted for local conditions. The relation of natural to anthropogenic factors can make more precise the standards of developed, prepared and ready to excavation ore reserves relying on computational methods. It is possible to minimize critical stresses and corresponding deformations due to dividing the ore field into sectors safe from the standpoint of geo-mechanics, and using less cost

  2. Isolation and identification of iron ore-solubilising fungus

    Directory of Open Access Journals (Sweden)

    Damase Khasa

    2010-09-01

    Full Text Available Potential mineral-solubilising fungi were successfully isolated from the surfaces of iron ore minerals. Four isolates were obtained and identified by molecular and phylogenetic methods as close relatives of three different genera, namely Penicillium (for isolate FO, Alternaria (for isolates SFC2 and KFC1 and Epicoccum (for isolate SFC2B. The use of tricalcium phosphate (Ca3(PO42in phosphate-solubilising experiments confirmed isolate FO as the only phosphate solubiliser among the isolated fungi. The bioleaching capabilities of both the fungus and its spent liquid medium were tested and compared using two types of iron ore materials, conglomerate and shale, from the Sishen Iron Ore Mine as sources of potassium (K and phosphorus (P. The spent liquid medium removed more K (a maximum of 32.94% removal, from conglomerate, than the fungus (a maximum of 21.36% removal, from shale. However, the fungus removed more P (a maximum of 58.33% removal, from conglomerate than the spent liquid medium (a maximum of 29.25% removal, from conglomerate. The results also indicated a potential relationship between the removal of K or P and the production of organic acids by the fungus. A high production of gluconic acid could be related to the ability of the fungus to reduce K and P. Acetic, citric and maleic acids were also produced by the fungus, but in lower quantities. In addition, particle size and iron ore type were also shown to have significant effects on the removal of potassium and phosphorus from the iron ore minerals. We therefore conclude that the spent liquid medium from the fungal isolate FO can potentially be used for biobeneficiation of iron ore minerals.

  3. Multi-elemental characterization of volcanic and vulcano-sedimentary rocks from Pina petroleum ore, central Cuba

    International Nuclear Information System (INIS)

    Montero-Cabrera, M.E.; Herrera-Peraza, E.; Betancourt-Tanda, L.; Campa-Menendez, R.; Diaz-Rizo, O.; Rodriguez-Martinez, N.; Segura-Soto, R.; Hernandez-Lopez, B.; Valdes-Lopez, S.

    1994-01-01

    Concentrations of 32 elements in 22 clay, limestone, tuff and volcanic rock samples from the Pina ore have been obtained by neutron activation and X-ray fluorescence analyses. Several LILE (large ion lithofile elements) and REE (rare earth element) concentration diagrams showed the calc-alkaline character of the volcanic rocks corresponding to the Greater Antilles Island, Arc. The basaltic andesite behavior of the rocks studied was confirmed by comparing the average concentrations obtained from tuffs and volcanic rocks with proper mean values of rock elemental compositions of the earth's crust. (Author)

  4. Multi-elemental characterization of volcanic and vulcano-sedimentary rocks from Pina petroleum ore, central Cuba

    Energy Technology Data Exchange (ETDEWEB)

    Montero-Cabrera, M.E.; Herrera-Peraza, E.; Betancourt-Tanda, L.; Campa-Menendez, R.; Diaz-Rizo, O. (Instituto Superior de Ciencia y Tecnologia Nuclear (ISCTN), La Habana (Cuba)); Rodriguez-Martinez, N.; Segura-Soto, R.; Hernandez-Lopez, B.; Valdes-Lopez, S. (Centro de Investigaciones y Desarrollo del Petroleo, La Habana (Cuba))

    1994-08-01

    Concentrations of 32 elements in 22 clay, limestone, tuff and volcanic rock samples from the Pina ore have been obtained by neutron activation and X-ray fluorescence analyses. Several LILE (large ion lithofile elements) and REE (rare earth element) concentration diagrams showed the calc-alkaline character of the volcanic rocks corresponding to the Greater Antilles Island, Arc. The basaltic andesite behavior of the rocks studied was confirmed by comparing the average concentrations obtained from tuffs and volcanic rocks with proper mean values of rock elemental compositions of the earth's crust. (Author).

  5. Impact of shallowly deposited ore-bearing dolomites on local soil pollution aureoles of As, Cd, Pb, and Zn in an old mining area

    Energy Technology Data Exchange (ETDEWEB)

    Fabijanczyk, Piotr; Zawadzki, Jaroslaw [Warsaw Univ. of Technology (Poland). Environmental Engineering Faculty

    2012-10-15

    The study area, located in Upper Silesian Industrial Region, was rich in significant amounts of ores that were classified of Mississippi Valley type. Being these ores especially rich in Pb and Zn, an intense development of mining and ore extraction industry was verified in this area. The goal of this study was to investigate how local pollution aureoles of As, Cd, Pb, and Zn were influenced by the presence of shallowly deposited ore-bearing dolomites. Very extensive sampling campaign was carried out, and over 1,000 samples were collected in the area of about 150 km{sup 2}. Local aureoles of investigated metals were calculated for two soil layers. The first one covered the part of soil core from the soil surface to the depth of 20 cm and the second one from the depth of 40 cm to the depth of 60 cm. All spatial distributions of particular metals in soil were calculated by means of ordinary kriging using free softwares QGIS and SAGA. Maximum concentrations of Pb and Zn in soil in study area were very high, reaching over 24,000 and 77,000 mg/kg, respectively. Maximum concentrations of As and Cd were also very high, reaching about 1,000 mg/kg. Those maximum values were observed in the direct vicinity of the Boles?aw mine and its mine dumps. Almost all local aureoles were located within the range of ore-bearing dolomites. It was especially visible for Pb and Zn, minerals very common in ore deposits. Otherwise, local aureoles of As and Cd were more related with the vicinity of mines and other pollution sources, being more associated to the anthropogenic pollution than to the presence of ore-bearing dolomites. The aureoles of Pb and Zn, and in moderate degree of As, were associated with a mineral composition of ores. Differently, the location, the shape, and spatial pattern of Cd aureoles suggest that they were mostly influenced by anthropogenic pollution. Anthropogenic factors were dominating over the lithogenic ones and masking the influence of the shallowly deposited

  6. Utilisation of iron ore tailings as aggregates in concrete

    OpenAIRE

    Francis Atta Kuranchie; Sanjay Kumar Shukla; Daryoush Habibi; Alireza Mohyeddin

    2015-01-01

    Sustainable handling of iron ore tailings is of prime concern to all stakeholders who are into iron ore mining. This study seeks to add value to the tailings by utilising them as a replacement for aggregates in concrete. A concrete mix of grade 40 MPa was prepared in the laboratory with water–cement ratio of 0.5. The concrete were cured for 1, 2, 3, 7, 14 and 28 days. The properties of the concrete such as workability, durability, density, compressive strength and indirect tensile strength we...

  7. Bioleaching of copper oxide ore by Pseudomonas aeruginosa

    Science.gov (United States)

    Shabani, M. A.; Irannajad, M.; Azadmehr, A. R.; Meshkini, M.

    2013-12-01

    Bioleaching is an environmentally friendly method for extraction of metal from ores. In this study, bioleaching of copper oxide ore by Pseudomonas aeruginosa was investigated. Pseudomonas aeruginosa is a heterotrophic bacterium that can produce various organic acids in an appropriate culture medium, and these acids can operate as leaching agents. The parameters, such as particle size, glucose percentage in the culture medium, bioleaching time, and solid/liquid ratio were optimized. Optimum bioleaching conditions were found as follows: particle size of 150-177 μm, glucose percentage of 6%, bioleaching time of 8 d, and solid/liquid ratio of 1:80. Under these conditions, 53% of copper was extracted.

  8. Helium and deuterium permeability in O-rings

    International Nuclear Information System (INIS)

    Lakner, J.F.

    1976-01-01

    To obtain more information on gas permeation through elastomeric O-rings, studies were performed on Parker Seal Company O-rings, Nos. 2-113, 2-006, 3-904, and 3-906, all made of a nitrile rubber. Also included in the tests was a valve packing (Autoclave Engineers) encased in AE Valve 20A-2142. Permeation experiments were run usually in duplicate to 82.7 MPa (12,000 psi) with helium and deuterium at room temperature. The data are extrapolated to give values for tritium

  9. Underground Milling of High-Grade Uranium Ore

    Energy Technology Data Exchange (ETDEWEB)

    Edwards, C., E-mail: chuck.edwards@amec.com [AMEC Americas Limited, Saskatoon, Saskatchewan (Canada)

    2014-05-15

    There are many safety and technical issues involved in the mining and progressing of high grade uranium ores such as those exploited in Northern Canada at present. With more of this type of mine due to commence production in the near future, operators have been looking at ways to better manage the situation. The paper describes underground milling of high-grade uranium ore as a means of optimising production costs and managing safety issues. In addition the paper presents some examples of possible process flowsheets and plant layouts that could be applicable to such operations. Finally an assessment of potential benefits from underground milling from a variety of viewpoints is provided. (author)

  10. Ore reserve estimation: a summary of principles and methods

    International Nuclear Information System (INIS)

    Marques, J.P.M.

    1985-01-01

    The mining industry has experienced substantial improvements with the increasing utilization of computerized and electronic devices throughout the last few years. In the ore reserve estimation field the main methods have undergone recent advances in order to improve their overall efficiency. This paper presents the three main groups of ore reserve estimation methods presently used worldwide: Conventional, Statistical and Geostatistical, and elaborates a detaited description and comparative analysis of each. The Conventional Methods are the oldest, less complex and most employed ones. The Geostatistical Methods are the most recent precise and more complex ones. The Statistical Methods are intermediate to the others in complexity, diffusion and chronological order. (D.J.M.) [pt

  11. Chemical separation of Th-230 from uranium ore

    International Nuclear Information System (INIS)

    Kikunaga, H.; Nakanishi, T.; Mitsugashira, T.; Hara, M.

    2001-01-01

    We are studying the decay processes of low energy nuclear isomer of Th-229. Our approach to produce Th-229m is (γ, n) reaction on Th-230, hence, about 100 μg of Th-230 is necessary as a target. However, our stock of Th-230 has run out during several experiments, thus, we tried to separate Th-230 from uranium ore. In this paper, the detail of a chemical separation procedure for Th-230 from uranium ore and the results are reported. (author)

  12. Pilot plant studies on the treatment of El Atshan Uranium Ores, Eastern Desert, Egypt.

    Energy Technology Data Exchange (ETDEWEB)

    Abd Elghany, M S; Mahdy, M A [Nuclear materials authority, El-Maadi, Cairo, (Egypt); Abd El-Monem, A M; El-Hazek, A T [Faculty of engineering, Cairo university, Cairo, (Egypt)

    1995-10-01

    The present work deals with studying the different processes leading to the preparation of commercial uranium concentrate (yellow cake) from El Atshan granitic ore material (0.077%U) after acid leading of the latter, the two common extraction techniques of uranium from the obtained sulphate leach liquor; namely, anion exchange rein and solvent extraction have been studied. The studied leaching and extraction conditions-realized on the lab scale-were applied to inches pilot plant unit (capacity 150 kg ore). An average leaching leaching efficiency exceeding 88% has been achieved. Using anion exchange resin, it has been possible to prepare a uranium peroxide concentrate assaying a uranium content of about 67% U{sub 3} O{sub 8}. Only trace amount of Ca, Fe, Po{sub 4}, Cr and Pb have been detected. On the other hand, sodium uranate, as a uranium precipitate was prepared from the strip solution of the loaded solvent (di-2-ethyl) phosphoric acid concerned with the evaluation of a new optimized technique for the principle of chloramine-T method used for insulin iodination for the modified procedure can be carried out under normal condition of room temperature, employed longer reaction times and omitted the addition of inorganic reducing salts maintaining efficient iodination and avoiding denaturation to obtain labels of exceedingly high specific activity and small quantities of insulin for in vitro usage in the investigation of human erythrocytes 125 I-inulin binding capacity in normal and in some disease status. 9 figs., 2 tabs.

  13. Effects of High Pressure ORE Grinding on the Efficiency of Flotation Operations

    Science.gov (United States)

    Saramak, Daniel; Krawczykowska, Aldona; Młynarczykowska, Anna

    2014-10-01

    This article discusses issues related to the impact of the high pressure comminution process on the efficiency of the copper ore flotation operations. HPGR technology improves the efficiency of mineral resource enrichment through a better liberation of useful components from waste rock as well as more efficient comminution of the material. Research programme included the run of a laboratory flotation process for HPGR crushing products at different levels of operating pressures and moisture content. The test results showed that products of the high-pressure grinding rolls achieved better recoveries in flotation processes and showed a higher grade of useful components in the flotation concentrate, in comparison to the ball mill products. Upgrading curves have also been marked in the following arrangement: the content of useful component in concentrate the floatation recovery. All upgrading curves for HPGR products had a more favourable course in comparison to the curves of conventionally grinded ore. The results also indicate that various values of flotation recoveries have been obtained depending on the machine operating parameters (i.e. the operating pressure), and selected feed properties (moisture).

  14. Pilot plant studies on the treatment of El Atshan Uranium Ores, Eastern Desert, Egypt

    International Nuclear Information System (INIS)

    Abd Elghany, M.S.; Mahdy, M.A.; Abd El-Monem, A.M.; El-Hazek, A.T.

    1995-01-01

    The present work deals with studying the different processes leading to the preparation of commercial uranium concentrate (yellow cake) from El Atshan granitic ore material (0.077%U) after acid leading of the latter, the two common extraction techniques of uranium from the obtained sulphate leach liquor; namely, anion exchange rein and solvent extraction have been studied. The studied leaching and extraction conditions-realized on the lab scale-were applied to inches pilot plant unit (capacity 150 kg ore). An average leaching leaching efficiency exceeding 88% has been achieved. Using anion exchange resin, it has been possible to prepare a uranium peroxide concentrate assaying a uranium content of about 67% U 3 O 8 . Only trace amount of Ca, Fe, Po 4 , Cr and Pb have been detected. On the other hand, sodium uranate, as a uranium precipitate was prepared from the strip solution of the loaded solvent (di-2-ethyl phosphoric acid concerned with the evaluation of a new optimized technique for the principle of chloramine-T method used for insulin iodination for the modified procedure can be carried out under normal condition of room temperature, employed longer reaction times and omitted the addition of inorganic reducing salts maintaining efficient iodination and avoiding denaturation to obtain labels of exceedingly high specific activity and small quantities of insulin for in vitro usage in the investigation of human erythrocytes 125 I-inulin binding capacity in normal and in some disease status. 9 figs., 2 tabs

  15. Lixiviation of uranium ores by capillarity; Lixiviation par capillarite des minerais d'uranium (1962)

    Energy Technology Data Exchange (ETDEWEB)

    Mouret, P; Pottier, P [Commissariat a l' Energie Atomique, Fontenay-aux-Roses (France). Centre d' Etudes Nucleaires

    1962-07-01

    All chemical concentration plants use at the moment a process of lixiviation by agitation for the treatment of uranium ores. It has become necessary for various reasons to study the application of a more economical system which is that of the lixiviation by capillarity in heaps. After presenting the laboratory tests for recognizing the ability of an ore for this type of lixiviation, the authors give an outline of the two semi-industrial tests which are still in progress. The results are such that it has been possible to plan larger installations which are now under construction. (authors) [French] Les usines de concentration chimique utilisent toutes actuellement la lixiviation par agitation des minerais d'uranium. Il est devenu necessaire pour diverses raisons d'etudier l'application d'un procede plus economique, qui est celui de la lixiviation par capillarite en tas. Apres un expose des tests de laboratoire permettant de connaitre l'aptitude d'un minerai a ce type de lixiviation, est donne un apercu de deux essais semi-industriels non encore acheves a ce jour. Les resultats sont tels, qu'ils ont permis de projeter des installations plus importantes, qui sont actuellement en construction. (auteurs)

  16. Ore-controlling mechanism of carbonaceous-siliceous-pelitic rock type uranium deposits with down-faulted red basins in the southeast continental margin of Yangtze plate

    International Nuclear Information System (INIS)

    Zhang Zilong; Qi Fucheng; He Zhongbo; Li Zhixing; Wang Wenquan; Yu Jinshui

    2012-01-01

    One of the important ore-concentrated areas of carbonaceous-siliceous-pelitic rock type uranium deposits is the Southeast continental margin of Yangtze plate. Sedimentary-exogenously transformed type and sedimentary- hydrothermal superimposed transformed type uranium deposits are always distributed at or near the edge of down-faulted red ba sins. In this paper, the distributions of the deposits are analyzed with the relation to down-faulted red basins. The connective effect and ore-controlling mechanism are proposed of carbonaceous-siliceous-pelitic rock type uranium deposits with marginal fractures of red basins. (authors)

  17. Understanding Cu release into environment from Kure massive sulfide ore deposits, Kastamonu, NW Turkey

    Science.gov (United States)

    Demirel, Cansu; Sonmez, Seref; Balci, Nurgul

    2014-05-01

    Covering a wide range on the earth's crust, oxidation of metal sulfide minerals have vital environmental impacts on the aquatic environment, causing one of the major environmental problems known as acid mine drainage (AMD). Located in the Kastamonu province of the Western Black Sea region, Kure district is one of the major copper mining sites in Turkey. Mining activities in the area heads back to ancient times, such that operation is thought to be started with the Roman Empire. Currently, only the underground mining tunnels of Bakibaba and Asikoy are being operated. Thus, mining heaps and ores of those pyritic deposits have been exposed to the oxidative conditions for so long. As a result of weathering processes of past and recent heaps of the Kure volcanic massive sulfide deposits in addition to the main ore mineral (chalcopyrite), significant amount of metals, especially Cu, are being released into the environment creating undesirable environmental conditions. In order to elucidate Cu release mechanisms from Kure pyritic ore deposits and mining wastes, field and laboratory approaches were used. Surface water and sediment samples from the streams around the mining and waste sites were collected. Groundwater samples from the active underground mining site were also collected. Physical parameters (pH, Eh, T°C, and EC) of water samples were determined in situ and in the laboratory using probes (WTW pH 3110, WTW Multi 9310 and CRISON CM 35). Metal and ion concentrations of the water samples were analysed using ICP-MS and DR 2800 spectrophotometer, respectively. High Cu, Co, Zn and Fe concentrations were determined in the water samples with pH values ranging from 2.9- 4. Cu concentrions ranges from 345 ppm to 36 ppm in the water samples. Consistent with the water samples, high Cu, Fe, Zn and Co were also determined in the sediment samples. Laboratory chalcopyrite oxidation experiments under the conditions representing the field site were set up as biological and

  18. Studies on the recovery of uranium from low-grade ores in India

    International Nuclear Information System (INIS)

    Jayaram, K.M.V.; Dwivedy, K.K.; Deshpande, A.S.; Ramachar, T.M.

    1976-01-01

    Investigations were carried out to utilize the available para-marginal and low-grade ores - chlorite schists, amphibolites, carbonate ores, clays and quartzites - analysing between 0.027 and 0.08% U 3 O 8 . In addition, tests were undertaken on the technical and economic feasibility of recovering uranium as a byproduct from the copper flotation tailings and phosphorites. Heap and bacterial leaching tests were conducted on quartz-chlorite schists from the Singhbhum district, Bihar, analysing about 0.03% U 3 O 8 . Studies also showed that the ores harbour active Ferrobacillus ferrooxidans. Studies on 10-mesh samples of amphibolites from Inderwa, Bihar, (0.08% U 3 O 8 ) showed that only 32.8% recovery could be obtained by wet tabling and 85% by agitation leaching, while static leaching tests yielded 81% recovery in 24 hours of contact time. Similar tests on calcareous phyllites (0.05% U 3 O 8 ) with 30 kg/t Na 2 CO 3 and 8 kg/t NaHCO 3 yielded 86% uranium leachability at ambient temperature. Biogenic uraniferous clay from Udaisagar (0.029% U 3 O 8 ) yielded 43.3% uranium recovery using 1000 l/t of neutral water for 6 h. Percolation leaching tests were conducted with hard quartzites (0.06% U 3 O 8 ), and the results showed that 81% uranium could be recovered in 24 days. Although preliminary ore dressing studies on tailings obtained from the copper flotation (0.013% U 3 O 8 ) at Surda yielded a concentrate analysing 0.063% U 3 O 8 at 66% recovery, recent tests on the tailings from the copper concentrator indicated only 48% recovery at a grade of 0.112% owing to decrease in the feed grade. Studies on the utilization of large-capacity gravity machines and selective mining of uranium-rich copper lodes may render this source economic. Preliminary studies on a phosphorite sample containing 22.0% P 2 O 5 and 0.04% U 3 O 8 from the Mussorie area in Uttar Pradesh on calcination followed by scrubbing yielded a sand enriched in P 2 O 5 values (33.7% P 2 O 5 at 92.5% recovery) but

  19. A study of the distribution of rare-metals in kuroko-type ore

    Energy Technology Data Exchange (ETDEWEB)

    Murao, S. [Commonwealth Scientific and Industrial Research Organisation (CSIRO), North Ryde, NSW (Australia). Div. of Exploration Geoscience]|[Geological Survey of Japan, Tsukuba, Ibaraki (Japan); Sie, S.H.; Suter, G.F. [Commonwealth Scientific and Industrial Research Organisation (CSIRO), North Ryde, NSW (Australia). Div. of Exploration Geoscience

    1996-12-31

    We have performed PIXE analysis of kuroko-type ore from the JADE hydrothermal site of the Okinawa Trough, Japan using the proton microprobe (PIXEPROBE). We analysed five kinds of ores dredged from the sea floor: (I) barite ore with small sulfide dissemination; (2) sphalerite-pyrite chimney; (3) pyrite ore; (4) sulfide veinlets in strongly altered rock; and (5) pyrite megacrystals in strongly altered rock. The analyses revealed that the trace element distribution is regulated by the occurrence mode of the ore, and within each ore, by the crystal structure. The distribution suggests that the hydrothermal system for kuroko ore formation is quite heterogeneous and its chemistry is controlled by local factors such as difference in temperature, and that in-situ PIXE analyses are essential for effective beneficiation strategy for the rare-metals from kuroko-type ore. (authors). 10 refs., 1 tab.

  20. A study of the distribution of rare-metals in kuroko-type ore

    Energy Technology Data Exchange (ETDEWEB)

    Murao, S [Commonwealth Scientific and Industrial Research Organisation (CSIRO), North Ryde, NSW (Australia). Div. of Exploration Geoscience; [Geological Survey of Japan, Tsukuba, Ibaraki (Japan); Sie, S H; Suter, G F [Commonwealth Scientific and Industrial Research Organisation (CSIRO), North Ryde, NSW (Australia). Div. of Exploration Geoscience

    1997-12-31

    We have performed PIXE analysis of kuroko-type ore from the JADE hydrothermal site of the Okinawa Trough, Japan using the proton microprobe (PIXEPROBE). We analysed five kinds of ores dredged from the sea floor: (I) barite ore with small sulfide dissemination; (2) sphalerite-pyrite chimney; (3) pyrite ore; (4) sulfide veinlets in strongly altered rock; and (5) pyrite megacrystals in strongly altered rock. The analyses revealed that the trace element distribution is regulated by the occurrence mode of the ore, and within each ore, by the crystal structure. The distribution suggests that the hydrothermal system for kuroko ore formation is quite heterogeneous and its chemistry is controlled by local factors such as difference in temperature, and that in-situ PIXE analyses are essential for effective beneficiation strategy for the rare-metals from kuroko-type ore. (authors). 10 refs., 1 tab.