Fabrication of steel matrix composites locally reinforced with different ratios of TiC/TiB2 particulates using SHS reactions of Ni-Ti-B4C and Ni-Ti-B4C-C systems during casting

International Nuclear Information System (INIS)

Yang Yafeng; Wang Huiyuan; Liang Yunhong; Zhao Ruyi; Jiang Qichuan

2007-01-01

Steel matrix composites locally reinforced with different molar ratios of in situ TiC/TiB 2 particulates (2:1, 1:1 and 1:2, respectively) have been fabricated successfully utilizing the self-propagating high-temperature synthesis (SHS) reactions of Ni-Ti-B 4 C and Ni-Ti-B 4 C-C systems during casting. Differential thermal analysis (DTA) and X-ray diffraction (XRD) results reveal that the exothermic reactions of the Ni-Ti-B 4 C and Ni-Ti-B 4 C-C systems proceed in such a way that Ni initially reacts with B 4 C and Ti to form Ni 2 B and Ti 2 Ni compounds, respectively, with heat evolution at 1037 deg. C; Subsequently, the external heat and the evolved heat from these exothermic reactions promote the reactions forming TiC and TiB 2 at 1133 deg. C. In the composites reinforced with 1:2 molar ratio of TiC/TiB 2 , almost all TiB 2 grains have clubbed structures, while TiC grains exhibit near-spherical morphologies. Furthermore, TiB 2 grain sizes decrease, with the increase of TiC content. In particular, in the composites reinforced with 2:1 molar ratio of TiC/TiB 2 , it is difficult to find the clubbed TiB 2 grains. Macro-pores and blowholes are absent in the local reinforcing region of the composites reinforced with 1:1 and 1:2 molar ratios of TiC/TiB 2 , while a few macro-pores can be observed in the composite reinforced with 2:1 molar ratio of TiC/TiB 2 . Moreover, the densities of the composites reinforced with 1:1 and 1:2 molar ratios of TiC/TiB 2 are higher than that of the composite reinforced with 2:1 molar ratio of TiC/TiB 2 . The composite reinforced with 1:2 molar ratio of TiC/TiB 2 has the highest hardness and the best wear resistance

High-frequency permeability of electroplated CoNiFe and CoNiFe-C alloys

International Nuclear Information System (INIS)

Rhen, Fernando M.F.; McCloskey, Paul; O'Donnell, Terence; Roy, Saibal

2008-01-01

We have investigated CoNiFe and CoNiFe-C electrodeposited by pulse reverse plating (PRP) and direct current (DC) techniques. CoNiFe(PRP) films with composition Co 59.4 Fe 27.7 Ni 12.8 show coercivity of 95 A m -1 (1.2 Oe) and magnetization saturation flux (μ 0 M s ) of 1.8 T. Resistivity of CoNiFe (PRP) is about 24 μΩ cm and permeability remains almost constant μ r ' ∼475 up to 30 MHz with a quality factor (Q) larger than 10. Additionally, the permeability spectra analysis shows that CoNiFe exhibits a classical eddy current loss at zero bias field and ferromagnetic resonance (FMR) when biased with 0.05 T. Furthermore, a crossover between eddy current and FMR loss is observed for CoNiFe-PRP when baised with 0.05 T. DC and PRP plated CoNiFe-C, which have resistivity and permeability of 85, 38 μΩ cm, μ r '=165 and 35 with Q>10 up to 320 MHz, respectively, showed only ferromagnetic resonance losses. The ferromagnetic resonance peaks in CoNiFe and CoNiFe-C are broad and resembles a Gaussian distribution of FMR frequencies. The incorporation of C to CoNiFe reduces eddy current loss, but also reduces the FMR frequency

Laser alloying of AI with mixed Ni, Ti and SiC powders

CSIR Research Space (South Africa)

Mabhali, Luyolo AB

2010-03-01

Full Text Available composite (MMC) is formed. The MMC layer has excellent hardness and wear resistance compared to the base alloy [9-13]. Man et al. [14] used a high power continuous wave Nd:YAG laser to alloy aluminium AA 6061 with preplaced NiTi (54 wt% Ni & 46 wt...Al, Ti3Al, SiC, Al and Si phases. The hardness increased from 75HV to 650HV due to the formation of the TiC particles and TiAl and Ti3Al intermetallics. Su and Lei [9] laser cladded Al-12wt%Si with a powder containing SiC and Al-12wt%Si in a 3...

Preparation of Ni-C Ultrafine Composite from Waste Material

Directory of Open Access Journals (Sweden)

Mahmoud A. Rabah

2017-06-01

Full Text Available This work depicts the preparation of Ni-C ultrafine composite from used engine oil. The used oil was emulsified with detergent loaded with Ni (OH2. The loaded emulsion was sprayed on electric plasma generated between two C electrodes to a DC main 28 V and 70-80 A. The purged Ni-doped carbon fume was trapped on a polymer film moistened with synthetic adhesive to fix the trapped smoke. Characterization of the deposit was made using SEM. XRD examined the crystal morphology. Carbon density in the cloud was calculated. The average size and thickness of the deposited composite is 120-160 nm. Aliphatic hydrocarbons readily decompose to gaseous products. Solid carbon smoke originates from aromatic compounds. Plasma heat blasts the oil in short time to decompose in one step.

Interfacial reaction of Ni{sub 3}Sn{sub 4} intermetallic compound in Ni/SnAg solder/Ni system under thermomigration

Energy Technology Data Exchange (ETDEWEB)

Yang, Yi-Shan; Yang, Chia-Jung; Ouyang, Fan-Yi, E-mail: fyouyang@ess.nthu.edu.tw

2016-07-25

The growth of Ni{sub 3}Sn{sub 4} intermetallic compound (IMC) between liquid–solid interface in micro-scale Ni/SnAg/Ni system was investigated under a temperature gradient of 160 °C/cm at 260 °C on a hot plate. In contrast to a symmetrical growth of Ni{sub 3}Sn{sub 4} on both interfaces under isothermally annealed at 260 °C, the interfacial Ni{sub 3}Sn{sub 4} IMC exhibited asymmetric growth under a temperature gradient; the growth of Ni{sub 3}Sn{sub 4} at cold interface was faster than that at hot side because of temperature gradient induced mass migration of Ni atoms from the hot end toward the cold end. It was found that two-stage growth behavior of Ni{sub 3}Sn{sub 4} IMC under a temperature gradient. A growth model was established and growth kinetic analysis suggested that the chemical potential gradient controlled the growth of Ni{sub 3}Sn{sub 4} at stage I (0–120 min) whereas the dynamic equilibrium between chemical potential gradient and temperature gradient forces was attained at the hot end at stage II (120–210 min). When dynamic equilibrium was achieved at 260 °C, the critical length-temperature gradient product at the hot end was experimentally estimated to be 489.18 μm × °C/cm and the moving velocity of Ni{sub 3}Sn{sub 4} interface due to Ni consumption was calculated to be 0.134 μm/h. The molar heat of transport (Q*) of Ni atoms in molten SnAg solder was calculated to be +0.76 kJ/mol. - Highlights: • Interfacial reaction in Ni/SnAg solder/Ni system under thermal gradient. • Growth rate of Ni{sub 3}Sn{sub 4} at cold end is faster than that at hot end. • Critical length-temperature gradient product at hot end is 489.2 μm°C/cm at 260 °C. • Velocity of Ni{sub 3}Sn{sub 4} moving interface is 0.134 μm/h during dynamic equilibrium. • Molar heat of transport (Q*) of Ni in molten SnAg was +0.76 kJ/mol.

Formation Mechanism of Spherical TiC in Ni-Ti-C System during Combustion Synthesis.

Science.gov (United States)

Zhu, Guoliang; Wang, Wei; Wang, Rui; Zhao, Chuanbao; Pan, Weitao; Huang, Haijun; Du, Dafan; Wang, Donghong; Shu, Da; Dong, Anping; Sun, Baode; Jiang, Sheng; Pu, Yilong

2017-08-29

The formation mechanism of TiC particles in a Ni-Ti-C system were revealed by using differential thermal analysis (DTA), XRD, and SEM to identify the reaction products in different temperature ranges. The results indicated that the synthesis mechanism of TiC in Ni-Ti-C system was complex; several reactions were involved in the combustion synthesis of TiC-Ni composite. The Ni-Ti intermediate phases play important roles during the formation of TiC. Moreover, the influence of heating rate on the size range of TiC was also discussed.

C-IOP/NiO/Ni7S6 composite with the inverse opal lattice as an electrode for supercapacitors

Science.gov (United States)

Sukhinina, Nadezhda S.; Masalov, Vladimir M.; Zhokhov, Andrey A.; Zverkova, Irina I.; Emelchenko, Gennadi A.

2015-06-01

In this work, we demonstrate the results of studies on the synthesis, the structure and properties of carbon inverted opal (C-IOP) nanostructures, the surface of which is modified by oxide and sulfide of nickel. It is shown that the modification of the matrix C-IOP by nickel compounds led to a decreasing the specific surface area more than three times and was 250 m2/g. The specific capacitance of the capacitor with the C-IOP/NiO/Ni7S6 composite as electrode has increased more than 4 times, from 130 F/g to 600 F/g, as compared with the sample C-IOP without the modification by nickel compounds. The significant contribution of the faradaic reactions in specific capacitance of the capacitor electrodes of the composites is marked.

One-step facile synthesis of Ni2P/C as cathode material for Ni/Zn aqueous secondary battery

Science.gov (United States)

Li, JiLan; Chen, ChangGuo

2018-01-01

Nickel phosphides/carbon(Ni2P/C) composites have been successfully synthesized via a simple one-pot hydrothermal method using glucose as carbon source for the first time. By contrast, the pure Ni2P was prepared under the same conditions without glucose. The results show that glucose not only provide the carbon source, but also prevent the aggregation of Ni2P particles. The as-obtained Ni2P/C composites and pure Ni2P were used as cathode material for alkaline Ni/Zn battery. Owing to unique Ni2P/C composites and loose, Ultra thin flower-like shape the synthesized Ni2P/C material delivers high capacity of 176 mAh g-1 at 1 A g-1 and 82 mAh g-1 at 5 A g-1 current density in Ni2P/C-Zn battery. Moreover, it shows a good cycling life that capacity fading only about 6.2% after 1500 cycles. All of these indicate that the prepared Ni2P/C composites may be a new promising cathode material for Ni-Zn rechargeable battery.

Hydrogenation and crystal structures of the Nd(Ni1-xCux)(In1-yAly) intermetallics and their hydrides

International Nuclear Information System (INIS)

Riabov, A.B.; Denys, R.V.; Sato, Masashi; Delaplane, R.G.; Yartys, V.A.

2005-01-01

The crystal structure of NdNiInD 1.2 contains D-D pairs with the shortest known D...D separation of 1.56-bar A. This work was aimed on studies of the factors influencing the formation and the length of such a pair. We have studied the NdNiIn-based alloys, in which Ni or In are partially substituted by the chemically related elements, Cu or Al, respectively. Three equiatomic intermetallics, NdNiIn, NdCuIn and NdNiAl, are isostructural and crystallise with the ZrNiAl type of structure. In the NdNi 1-x Cu x In (x=0; 0.02; 0.05; 0.25; 0.50; 0.75 and 1.00) quaternary system a complete solid solubility range has been found. In contrast, in the Al-containing NdNiIn 1-x Al x alloys the range of a solid solution is limited to the region NdNiIn-NdNiIn 0.75 Al 0.25 . The substitutions result in regular changes in V, a, c and c/a of the hexagonal unit cells. Small substitutions by Cu and Al (x,y-bar 0.05) do not lead to significant changes in H content and types of the crystal structures formed (PND data). However, a decrease in the stability of the hydrides is observed. In NdNi 1-x Cu x In, Cu has a strong preference for the occupation of the 1b CuIn 6 trigonal prisms. An increase of the Cu content is accompanied by a decrease of the D/Nd(Ni 1-x Cu x )In ratio and a distinct growth of the distance between Ni(Cu) and D (from 1.51 to 1.84-bar A). H...H pairing is very sensitive to the content of both Al and Cu. When the level of substitution exceeds Cu/Ni(Al/In)>1/9, H pairing becomes unstable and H atoms favour other types of ordering in the metal sublattice

Synthesis, characterization, and reactivity of nickel hydride complexes containing 2,6-C6H3(CH2PR2)2 (R = tBu, cHex, and iPr) pincer ligands.

Science.gov (United States)

Boro, Brian J; Duesler, Eileen N; Goldberg, Karen I; Kemp, Richard A

2009-06-15

The syntheses and full characterization of nickel hydrides containing the PCP "pincer"-type ligand, where PCP = 2,6-C(6)H(3)(CH(2)PR(2))(2) (R = tBu, cHex, and iPr), are reported. These Ni-H complexes are prepared by the conversion of ((R)PCP)NiCl precursors into the corresponding nickel hydrides by use of appropriate hydride donors. Surprisingly, although the ((R)PCP)NiCl precursors are quite similar chemically, the conversions to the hydrides were not straightforward and required different hydride reagents to provide analytically pure products. While NaBH(4) was effective in the preparation of pure ((tBu)PCP)NiH, Super-Hydride solution (LiEt(3)BH in THF) was required to prepare either ((cHex)PCP)NiH or ((iPr)PCP)NiH. Attempts to prepare a Ni-H from ((Ph)PCP)NiCl with a variety of hydride reagents yielded only the free ligand as an identifiable product. Two of the derivatives, tBu and cHex, have also been subjected to single crystal X-ray analysis. The solid-state structures each showed a classic, near-square planar arrangement for Ni in which the PCP ligand occupied three meridional ligand points with the Ni-H trans to the Ni-C bond. The resulting Ni-H bond lengths were 1.42(3) and 1.55(2) A for the tBu and cHex derivatives, respectively.

Swift heavy ion irradiation effects in Pt/C and Ni/C multilayers

Science.gov (United States)

Gupta, Ajay; Pandita, Suneel; Avasthi, D. K.; Lodha, G. S.; Nandedkar, R. V.

1998-12-01

Irradiation effects of 100 MeV Ag ion irradiation on Ni/C and Pt/C multilayers have been studied using X-ray reflectivity measurements. Modifications are observed in both the multilayers at (dE/dx)e values much below the threshold values for Ni and Pt. This effect is attributed to the discontinuous nature of the metal layers. In both the multilayers interfacial roughness increases with irradiation dose. While Ni/C multilayers exhibit large ion-beam induced intermixing, no observable intermixing is observed in the case of Pt/C multilayer. This difference in the behavior of the two systems suggests a significant role for chemically guided defect motion in the mixing process associated with swift heavy ion irradiation.

11C-radioisotope study of methanol co-reaction with ethanol over Ni-MCM-41 silica-alumina and Ni-alumina

International Nuclear Information System (INIS)

Sarkadi-Priboczki, E.; Kovacs, Z.; Tsoncheva, T.; Kumar, N.; Murzin, D.Yu.

2009-01-01

Complete text of publication follows. The Ni modifies the properties of acidic alumina and light acidic MCM-41 silica-alumina supports. The radioisotopic method is a suitable tool for distinction of the 11 Cradioisotopic methanol and its co-derivates from derivates of non-radioactive ethanol on these catalysts. Experimental. The Ni/A l 2O 3 (5 wt % Ni) is commercially available while H-MCMN-41 (Si/Al=20) and Ni-ion-exchanged MCM-41 silica-alumina (5 wt % Ni) were prepared and characterized in previous works. Before catalysis the Ni/Al 2 O 3 and Ni-MCM-41 were pre-reduced. The 11 C-methanol was formed by a radiochemical process from 11 C-carbon dioxide produced at cyclotron (T 1/2 = 20.4 min). The mixture of equivalent volume of radioactive methanol and non-radioactive ethanol was introduced into glass tube micro-flow reactor at ambient temperature. After adsorption, the valves were closed and the catalyst was heated up to the required temperatures. The desorption rate of the remaining 11 C-derivatives on catalysts were continuously followed by radiodetectors and the derivatives of methanol with ethanol were analyzed by Radio/FID-gas chromatography (FID is coupled on-line with a radiodetector). The ethanol and its derivates were identified by FID while the 11 C-methanol and its co-derivates (with ethanol) were detected by both of FID and radiodetector. Results The 11 C-dimethyl ether was the common product of the single 11 C-methanol transformation on H-MCM-41, Ni-MCM-41 and Ni- Al 2 O 3 at low temperature (200-280 degC) due to middle strong acid sites. At higher temperature (280-350 degC), the dimethyl ether and hydrocarbons were the dominant products on H-MCM-41 while dimethyl ether selectivity decreased on Ni-alumina and Ni-MCM-41 in favor of methane. The selectivities of methanol to formaldehyde and methane were the highest on Ni-MCM-41. During co-reaction of 11 C-methanol with non-radioactive ethanol, the 11 C-labeled coethers, namely 11 C-methyl ethyl ether

Effect of annealing temperature on the contact properties of Ni/V/4H-SiC structure

Directory of Open Access Journals (Sweden)

Chong-Chong Dai

2014-04-01

Full Text Available A sandwich structure of Ni/V/4H-SiC was prepared and annealed at different temperatures from 650 °C to 1050 °C. The electrical properties and microstructures were characterized by transmission line method, X-ray diffraction, Raman spectroscopy and transmission electron microscopy. A low specific contact resistance of 3.3 × 10-5 Ω·cm2 was obtained when the Ni/V contact was annealed at 1050 °C for 2 min. It was found that the silicide changed from Ni3Si to Ni2Si with increasing annealing temperature, while the vanadium compounds appeared at 950 °C and their concentration increased at higher annealing temperature. A schematic diagram was proposed to explain the ohmic contact mechanism of Ni/V/4H-SiC structure.

Magnetic, thermodynamic and transport properties of novel non-centrosymmetric RCoSi{sub 3} (R=Pr, Nd and Sm) compounds

Energy Technology Data Exchange (ETDEWEB)

Nallamuthu, S. [Department of Physics, National Institute of Technology, Tiruchirappalli 620015, Tamil Nadu (India); Chandrasekaran, S. Selva; Murugan, P. [CSIR-Central Electrochemical Research Institute, Karaikudi 630006, Tamil Nadu (India); Reiffers, Marian [Faculty of Humanities and Natural Sciences, Presov University, Presov (Slovakia); Nagalakshmi, R., E-mail: nagaphys@yahoo.com [Department of Physics, National Institute of Technology, Tiruchirappalli 620015, Tamil Nadu (India)

2016-10-15

Novel non-centrosymmetric RCoSi{sub 3} (R = Pr, Nd and Sm) compounds crystallize in tetragonal BaNiSn{sub 3} type structure with space group I4 mm. The bulk magnetic ordering of all the compounds were confirmed from heat capacity data. Magnetization measurements indicate that PrCoSi{sub 3} orders ferromagnetically at 5.9 K, while NdCoSi{sub 3} and SmCoSi{sub 3} order antiferromagnetically at 4 K and 8 K respectively. The magnetic transitions were also manifested by the slope change of temperature dependent resistivity at low temperatures. The energy level schemes created by crystal electric field splitting are determined from Schottky contribution to specific heat. The existence of magnon gap like features at low temperatures are consistent in both heat capacity and resistivity for NdCoSi{sub 3} and SmCoSi{sub 3}. Large magnetoresistance is observed in NdCoSi{sub 3} and SmCoSi{sub 3}. First principles electronic structure calculation based on density functional theory framework have been performed and compared with experimental data. - Highlights: • Magnetic, transport and thermodynamic studies are investigated extensively. • PrCoSi{sub 3} orders T{sub C} = 5.9 K, NdCoSi{sub 3} and SmCoSi{sub 3} order T{sub N}=4 K and 8 K. • Large magnetoresistance is observed in NdCoSi{sub 3} and SmCoSi{sub 3}. • Density of states calculated at the Fermi levels [N(E{sub F})].

Laser alloying of Al with mixed Ni, Ti and SiC powders

CSIR Research Space (South Africa)

Mabhali, Luyolo AB

2010-11-01

Full Text Available Laser alloying of aluminium AA1200 was performed with a 4.4kW Rofin Sinar Nd:YAG laser to improve the surface hardness. Alloying was carried out by depositing Ni, Ti and SiC powders of different weight ratios on the aluminium substrate. The aim...

Effect of Ni Core Structure on the Electrocatalytic Activity of Pt-Ni/C in Methanol Oxidation

Directory of Open Access Journals (Sweden)

Vladimir Linkov

2013-07-01

Full Text Available Methanol oxidation catalysts comprising an outer Pt-shell with an inner Ni-core supported on carbon, (Pt-Ni/C, were prepared with either crystalline or amorphous Ni core structures. Structural comparisons of the two forms of catalyst were made using transmission electron microscopy (TEM, X-ray diffraction (XRD and X-ray photoelectron spectroscopy (XPS, and methanol oxidation activity compared using CV and chronoamperometry (CA. While both the amorphous Ni core and crystalline Ni core structures were covered by similar Pt shell thickness and structure, the Pt-Ni(amorphous/C catalyst had higher methanol oxidation activity. The amorphous Ni core thus offers improved Pt usage efficiency in direct methanol fuel cells.

Microstructure and martensitic transformation of Ni-Ti-Pr alloys

Energy Technology Data Exchange (ETDEWEB)

Zhao, Chunwang [Inner Mongolia University of Technology, College of Science, Hohhot (China); Shanghai Maritime University, College of Arts and Sciences, Shanghai (China); Zhao, Shilei; Jin, Yongjun; Hou, Qingyu [Inner Mongolia University of Technology, College of Science, Hohhot (China); Guo, Shaoqiang [Beihang University, Key Laboratory of Micro-nano Measurement, Manipulation and Physics (Ministry of Education), Department of Physics, Beijing (China)

2017-09-15

The effect of Pr addition on the microstructure and martensitic transformation behavior of Ni{sub 50}Ti{sub 50-x}Pr{sub x} (x = 0, 0.1, 0.3, 0.5, 0.7, 0.9) alloys were investigated experimentally. Results show that the microstructures of Ni-Ti-Pr alloys consist of the NiTi matrix and the NiPr precipitate with the Ti solute. The martensitic transformation start temperature decreases gradually with the increase in Pr fraction. The stress around NiPr precipitates is responsible for the decrease in martensitic transformation temperature with the increase in Pr fraction in Ni-Ti-Pr alloys. (orig.)

(001) 3C SiC/Ni contact interface: In situ XPS observation of annealing induced Ni_2Si formation and the resulting barrier height changes

International Nuclear Information System (INIS)

Tengeler, Sven; Kaiser, Bernhard; Chaussende, Didier; Jaegermann, Wolfram

2017-01-01

Highlights: • Schottky behavior (Φ_B = 0.41 eV) and Fermi level pining were found pre annealing. • Ni_2Si formation was confirmed for 5 min at 850 °C. • 3C/Ni_2Si Fermi level alignment is responsible for ohmic contact behavior. • Wet chemical etching (Si–OH/C–H termination) does not impair Ni_2Si formation. - Abstract: The electronic states of the (001) 3C SiC/Ni interface prior and post annealing are investigated via an in situ XPS interface experiment, allowing direct observation of the induced band bending and the transformation from Schottky to ohmic behaviour for the first time. A single domain (001) 3C SiC sample was prepared via wet chemical etching. Nickel was deposited on the sample in multiple in situ deposition steps via RF sputtering, allowing observation of the 3C SiC/Ni interface formation. Over the course of the experiments, an upward band bending of 0.35 eV was observed, along with defect induced Fermi level pinning. This indicates a Schottky type contact behaviour with a barrier height of 0.41 eV. The subsequent annealing at 850 °C for 5 min resulted in the formation of a Ni_2Si layer and a reversal of the band bending to 0.06 eV downward. Thus explaining the ohmic contact behaviour frequently reported for annealed n-type 3C SiC/Ni contacts.

Phase equilibria in the ternary In-Ni-Sn system at 700 °C.

Science.gov (United States)

Schmetterer, C; Zemanova, A; Flandorfer, H; Kroupa, A; Ipser, H

2013-04-01

The phase equilibria of the ternary system In-Ni-Sn were investigated experimentally at 700 °C using X-ray diffraction (XRD) and scanning electron microscopy (SEM) including electron micro probe analysis (EMPA) and energy dispersive X-ray spectroscopy (EDX). A corresponding isothermal section was established based on these results. This particular temperature was chosen because it allowed obtaining reliable results within reasonable time. The existence of the ternary phase InNi 6 Sn 5 was confirmed whereas the ternary compound In 2 NiSn, reported earlier in literature, was found to be part of a large solid solution field based on binary InNi. The ternary solubility of the binary phases was established, and continuous solid solutions were found between the isostructural phases Ni 3 Sn LT and InNi 3 as well as between Ni 3 Sn 2 HT and InNi 2 . In addition, this isothermal section could be well reproduced by CALPHAD modelling. The resulting calculated isotherm at 700 °C is presented, too, and compared with the experimental results.

(001) 3C SiC/Ni contact interface: In situ XPS observation of annealing induced Ni{sub 2}Si formation and the resulting barrier height changes

Energy Technology Data Exchange (ETDEWEB)

Tengeler, Sven, E-mail: stengeler@surface.tu-darmstadt.de [Institute of Material Science, Technische Universität Darmstadt, 64287 Darmstadt (Germany); Univ. Grenoble Alpes, CNRS, LMGP, F-38000 Grenoble (France); Kaiser, Bernhard [Institute of Material Science, Technische Universität Darmstadt, 64287 Darmstadt (Germany); Chaussende, Didier [Univ. Grenoble Alpes, CNRS, LMGP, F-38000 Grenoble (France); Jaegermann, Wolfram [Institute of Material Science, Technische Universität Darmstadt, 64287 Darmstadt (Germany)

2017-04-01

Highlights: • Schottky behavior (Φ{sub B} = 0.41 eV) and Fermi level pining were found pre annealing. • Ni{sub 2}Si formation was confirmed for 5 min at 850 °C. • 3C/Ni{sub 2}Si Fermi level alignment is responsible for ohmic contact behavior. • Wet chemical etching (Si–OH/C–H termination) does not impair Ni{sub 2}Si formation. - Abstract: The electronic states of the (001) 3C SiC/Ni interface prior and post annealing are investigated via an in situ XPS interface experiment, allowing direct observation of the induced band bending and the transformation from Schottky to ohmic behaviour for the first time. A single domain (001) 3C SiC sample was prepared via wet chemical etching. Nickel was deposited on the sample in multiple in situ deposition steps via RF sputtering, allowing observation of the 3C SiC/Ni interface formation. Over the course of the experiments, an upward band bending of 0.35 eV was observed, along with defect induced Fermi level pinning. This indicates a Schottky type contact behaviour with a barrier height of 0.41 eV. The subsequent annealing at 850 °C for 5 min resulted in the formation of a Ni{sub 2}Si layer and a reversal of the band bending to 0.06 eV downward. Thus explaining the ohmic contact behaviour frequently reported for annealed n-type 3C SiC/Ni contacts.

Improvement of the magnetic moment of NiZn ferrites induced by substitution of Nd3+ ions for Fe3+ ions

Science.gov (United States)

Wu, Xuehang; Chen, Wen; Wu, Wenwei; Wu, Juan; Wang, Qing

2018-05-01

Four types of Ni-Zn based ferrites materials having the general formula Ni0.5Zn0.5NdxFe2-xO4 (0.0 ≤ x ≤ 0.12) have been successfully synthesized by calcining oxalates in air and the influence of Nd content on the structure and magnetic properties of Ni0.5Zn0.5NdxFe2-xO4 is studied. X-ray diffraction examination confirms that a high-crystallized Ni0.5Zn0.5NdxFe2-xO4 with cubic spinel structure is obtained when the precursor is calcined at 1000 °C in air for 2 h. The substitutions of Nd3+ ions for partial Fe3+ ions do not change the spinel crystalline structure of MFe2O4. The incorporation of Nd3+ ions in place of Fe3+ ions in Ni-Zn ferrites increases the average crystallite size. Specific saturation magnetization decreases with increase in Nd content. This is because Nd3+ ions with smaller magnetic moment preferentially fill the octahedral sites. In addition, antiferromagnetic FeNdO3 increases with increase in Nd content. In this study, Ni0.5Zn0.5Nd0.08Fe1.92O4, calcined at 1000 °C, exhibits the highest magnetic moment (4.2954 μB) and the lowest coercivity (28.82 Oe).

Observation of the structural, optical and magnetic properties during the transformation from hexagonal NiS nano-compounds to cubic NiO nanostructures due to thermal oxidation

Energy Technology Data Exchange (ETDEWEB)

Linganiso, E.C., E-mail: elinganiso@csir.co.za [National Centre for Nano-Structured Materials, Council for Scientific and Industrial Research, P.O. Box 395, Pretoria 0001 (South Africa); DST/NRF Centre of Excellence in Strong Materials, Molecular Sciences Institute, School of Chemistry, University of the Witwatersrand, Private Bag 3, Johannesburg, Wits 2050 (South Africa); Mwakikunga, B.W., E-mail: bmwakikunga@csir.co.za [National Centre for Nano-Structured Materials, Council for Scientific and Industrial Research, P.O. Box 395, Pretoria 0001 (South Africa); Coville, N.J. [DST/NRF Centre of Excellence in Strong Materials, Molecular Sciences Institute, School of Chemistry, University of the Witwatersrand, Private Bag 3, Johannesburg, Wits 2050 (South Africa); Mhlanga, S.D. [Department of Applied Chemistry, University of Johannesburg, PO Box 17011, Doornfontein, 2028 Johannesburg (South Africa)

2015-04-25

Graphical abstract: The transition temperature of 350 °C for the formation of c-NiO from h-NiS oxidation was obtained from structural and optical property studies and by calculating the number of spins obtained from the EPR data. Vibrating sample magnetometry (VSM) shows that this pure NiS has both ferromagnetic ordering and paramagnetic domains. Further, the transition temperature of −9 °C of the pure α-NiS nano-alloys was confirmed by performing electrical measurements on the as-synthesized material. - Highlights: • Single hexagonal phase NiS obtained by microwave assisted hydrothermal synthesis. • NiS nanoalloys show both ferromagnetic and paramagnetic domains by VSM. • Structural evolution of annealed NiS and temperature dependent NiS oxidation presented. • Phase transition from NiS to NiO studied and correlated to the EPR spin population data and crystallite size. • Ferromagnetic and paramagnetic ordering observed for the raw NiS nanostructures. - Abstract: Single phase α-NiS nano-compounds with uniformly distributed hierarchical networks were synthesized by a microwave-assisted hydrothermal technique. The materials were evaluated for thermal stability under an oxidative environment and at temperatures between 150 °C and 600 °C. NiS materials showed stability at 300 °C and NiO formation was observed from 350 °C to 600 °C. The annealing effect on the crystalline size and IR absorption of the annealed samples is reported by XRD and FTIR studied. The EPR properties of the annealed materials were studied and compared to the oxidized materials. The transition temperature of 350 °C for the formation of NiO from NiS oxidation was confirmed by calculating the number of spins obtained from the EPR data. Vibrating sample magnetometry (VSM) shows that this pure NiS has both ferromagnetic ordering and paramagnetic domains. Further, the transition temperature of −9 °C of the pure α-NiS nano-compounds was confirmed by performing electrical

Understanding micro-diffusion bonding from the fabrication of B4C/Ni composites

Science.gov (United States)

Wang, Miao; Wang, Wen-xian; Chen, Hong-sheng; Li, Yu-li

2018-03-01

A Ni-B4C macroscopic diffusion welding couple and a Ni-15wt%B4C composite fabricated by spark plasma sintering (SPS) were used to understand the micro-scale diffusion bonding between metals and ceramics. In the Ni-B4C macroscopic diffusion welding couple a perfect diffusion welding joint was achieved. In the Ni-15wt%B4C sample, microstructure analyses demonstrated that loose structures occurred around the B4C particles. Energy dispersive X-ray spectroscopy analyses revealed that during the SPS process, the process of diffusion bonding between Ni and B4C particles can be divided into three stages. By employing a nano-indentation test, the room-temperature fracture toughness of the Ni matrix was found to be higher than that of the interface. The micro-diffusion bonding between Ni and B4C particles is quite different from the Ni-B4C reaction couple.

Isothermal sections of the Co-Ni-Ti system at 950 and 1 000 C

Energy Technology Data Exchange (ETDEWEB)

Li, Han; Jin, Zhanpeng [Central South Univ., Changsha (China). School of Materials Science and Engineering; Zhou, Peng [Hunan Univ. of Science and Technology, Xiangtan (China). Hunan Provincial Key Defense Lab. of High Temperature Wear Resisting Materials and Preparation Technology; Du, Yong [Central South Univ., Changsha (China). State Key Lab. of Powder Metallurgy

2018-02-15

The isothermal sections of the Co-Ni-Ti system at 950 and 1000 C were investigated experimentally. Diffusion couples were measured by electron probe microanalysis to construct the phase relations at 950 C, whereas eleven key alloys annealed at 1000 C were investigated using X-ray diffraction and electron probe microanalysis. The ternary phase, τ-(Co,Ni){sub 3}Ti (hP24-VCo{sub 3}), was observed at both temperatures. At 950 C, continuous solid solutions are formed between CoTi{sub 2} and NiTi{sub 2} as well as between CoTi and NiTi. Eight 3-phase regions, i. e. Ni{sub 3}Ti + (Co,Ni)Ti + τ, Ni{sub 3}Ti + γ-(Co,Ni) + τ, τ + c-Co{sub 2}Ti + (Co,Ni)Ti, τ + c-Co{sub 2}Ti + Co{sub 3}Ti, τ + Co{sub 3}Ti + γ-(Co,Ni), c-Co{sub 2}Ti + h-Co{sub 2}Ti + Co{sub 3}Ti, L + β-(Ti) + (Co,Ni)Ti{sub 2} and L + (Co,Ni)Ti{sub 2} + (Co,Ni)Ti, were constructed at 1000 C. Considerable ternary solubilities in Ni{sub 3}Ti, Co{sub 3}Ti and c-Co{sub 2}Ti were determined.

Crystal structure of the binder phase in a model HfC-TiC-Ni material

International Nuclear Information System (INIS)

Heiligers, Christiane; Neethling, Johannes H.

2008-01-01

The crystal structure of the binder phase in a model HfC-TiC-Ni sample produced by hot pressing is investigated. The nature of the binder depends on the amount of Hf and Ti that remains in solution with Ni after cooling. Four different crystal structures are identified by analysis of electron diffraction patterns obtained using transmission electron microscopy techniques and the composition of the phases determined by energy dispersive X-ray spectrometry. Three of the phases are cubic; Ni, Ni 3 (Ti,Hf) and Ni 23 (Ti,Hf) 6 with lattice parameters of 3.52 ± 0.05, 3.52 ± 0.03 and 10.70 ± 0.40 A, respectively. The hexagonal phase is an intermetallic Ni 3 Ti phase, with lattice parameters of a = b = 5.00 ± 0.20 A and c = 8.16 ± 0.20 A. The crystal structures are confirmed by simulations of the electron diffraction patterns using JEMS software

Cavitation resistance of surface composition "Steel-Ni-TiNi-TiNiZr-cBNCo", formed by High-Velocity Oxygen-Fuel spraying

Science.gov (United States)

Blednova, Zh. M.; Dmitrenko, D. V.; Balaev, E. U. O.

2018-01-01

The object of the study is a multilayered surface composition "Steel - a Multicomponent material with Shape Memory Effect - a wear-resistant layer" under conditions of cavitation effects in sea water. Multicomponent TiNi-based coatings with addition of alloying elements such as Zr in an amount up to 10% mass, allow to create a composite material with a gradient of properties at the interface of layers, which gives new properties to coatings and improves their performance significantly. The use of materials with shape memory effect (SME) as surface layers or in the composition of surface layered compositions allows to provide an effective reaction of materials to the influence of external factors and adaptation to external influences. The surface composite layer cBN-10%Co has high hardness and strength, which ensures its resistance to shock cyclic influences of collapsing caverns. The increased roughness of the surface of a solid surface composite in the form of strong columnar structures ensures the crushing of vacuum voids, redistributing their effect on the entire surface, and not concentrating them in certain zones. In addition, the gradient structure of the multilayer composite coating TiNi-Ti33Ni49Zr18-cBN-10%Co Co makes it possible to create conditions for the relaxation of stresses created by the variable impact load of cavitation caverns and the manifestation of compensating internal forces due to thermo-elastic martensitic transformations of SME materials. The cavitation resistance of the coating TiNi-Ti33Ni49Zr18-cBN-10%Co according to the criterion of mass wear is 15-20 times higher than that of the base material without coating and 10-12 times higher than that of the TiNi-TiNiZr coating. The proposed architecture of the multifunctional gradient composition, "steel-Ni-TiNi- Ti33Ni49Zr18-cBN-10%Co", each layer of which has its functional purpose, allows to increase the service life of parts operating under conditions of cavitation-fatigue loading in

Preparation of TiC/Ni3Al Composites by Upward Melt Infiltration

Institute of Scientific and Technical Information of China (English)

无

2000-01-01

TiC/Ni3Al composites have been prepared using upward infiltration method. The densificstion was performed by both Ni3Al melt filling and TiC sintering during the infiltration. The dissolution of TiC in liquid Ni3Al has been evidenced by finding Ni3(Al,Ti)C after fast cooling in the TiC/Ni3Al composites. The dissolution may be responsible for the infiltration and sintering. Compared with downward infiltration, the upward infiltration brought about higher strength and fracture toughness and shorter infiltration time. TiC/20 vol. pct Ni3Al composite processed by upward infiltration had a flexural strength of 1476 Mpa with a statistic Weibull modulus of 20.2 and a fracture toughness of 20.4 Mpa(m). Better mechanical properties may be attributed to melt unidirectional movement in upward infiltration.

Crystal structure of the compounds R8Ga3Co (R=Ce, Pr, Nd, Sm, Tb, Dy, Ho, Er, Tm)

International Nuclear Information System (INIS)

Grin', Yu.N.; Sichevich, O.M.; Gladyshevskij, R.E.; Yarmolyuk, Ya.P.

1984-01-01

The crystal structure of Pr 8 Ga 3 Co compounds is studied by the method of monocrystal (autodiffractometer, MoKsub(α)): space group P6 3 mc, a=10.489, c=6.910 A, Z=2. Coordination numbers of atoms are 11-14 for Pr, 11 for Ga, 7 for Co. The shortest interatomic distances are 3.365 for Pr-Pr, 3.047 for Pr-Ga, 2.75 A for Pr-Co. Pr 3 Ga 3 Co structure is akin to structures of R 2 In compounds (Ni 2 In type) and R 2 Ga (Cl 2 Pb type). Isostructural compounds form in systems of other rare earth metals with gallium and cobalt

Luminescence and optical spectroscopy of charge transfer processes in solid solutions Ni{sub C}Mg{sub 1−C}O and Ni{sub x}Zn{sub 1−x}O

Energy Technology Data Exchange (ETDEWEB)

Sokolov, V.I., E-mail: visokolov@imp.uran.ru [Institute of Metal Physics, Russian Academy of Science, Ural Branch, S. Kovalevskaya Street 18, 620990 Yekaterinburg (Russian Federation); Pustovarov, V.A.; Churmanov, V.N. [Ural Federal University, Mira Street 19, 620002 Yekaterinburg (Russian Federation); Gruzdev, N.B.; Uimin, M.A.; Byzov, I.V.; Druzhinin, A.V. [Institute of Metal Physics, Russian Academy of Science, Ural Branch, S. Kovalevskaya Street 18, 620990 Yekaterinburg (Russian Federation); Mironova-Ulmane, N.A. [Institute of Solid State Physics, University of Latvia, Kengaraga Street 8, LV-1063 Riga (Latvia)

2016-01-15

In this work photoluminescence spectra for Ni{sub c}Mg{sub 1−c}O and Ni{sub x}Zn{sub 1−x}O solid solutions with the rock-salt crystal structure were obtained under synchrotron radiation excitation. Periodical peaks in the photoluminescence excitation spectrum of Ni{sub c}Mg{sub 1−c}O (c=0.008) have been discovered for a wide-gap oxide doped with 3d impurities for the first time. They can be considered as LO phonon repetitions of the narrow zero phonon line resulted from the optical transitions into the p–d charge transfer exciton [d{sup 9}h] state. A close coincidence in energy of different peculiarities in the optical absorption and photoluminescence excitation spectra for the Ni{sub c}Mg{sub 1−c}O and Ni{sub x}Zn{sub 1−x}O solid solutions is due to the practically equal interatomic distances Ni–O in the investigated materials. The bulk of new experimental results is the trustworthy evidence that only the p–d charge transfer transitions manifest themselves in the spectral region of 3.5–6.5 eV. - Highlights: • Emission of Ni{sub c}Mg{sub 1−c}O nanocystals excited by synchrotron radiation is obtained. • LO phonon repetitions have been observed in PLE spectra of Ni{sub c}Mg{sub 1−c}O firstly for wide gap oxide materials doped with 3d impurities. • The [d{sup 9}h] acceptor exciton state in Ni{sub c}Mg{sub 1−c}O (c=0.008) are indirectly revealed. • The begin of PLE spectra of Ni{sub x}Zn{sub 1−x}O are not virtually shifted with a change of composition x. • The near energy coincidence of absorption peaks for nanocrystals NiO and single crystal Ni{sub c}Mg{sub 1−c}O (c=0.0006) manifests itself.

(001) 3C SiC/Ni contact interface: In situ XPS observation of annealing induced Ni2Si formation and the resulting barrier height changes

Science.gov (United States)

Tengeler, Sven; Kaiser, Bernhard; Chaussende, Didier; Jaegermann, Wolfram

2017-04-01

The electronic states of the (001) 3C SiC/Ni interface prior and post annealing are investigated via an in situ XPS interface experiment, allowing direct observation of the induced band bending and the transformation from Schottky to ohmic behaviour for the first time. A single domain (001) 3C SiC sample was prepared via wet chemical etching. Nickel was deposited on the sample in multiple in situ deposition steps via RF sputtering, allowing observation of the 3C SiC/Ni interface formation. Over the course of the experiments, an upward band bending of 0.35 eV was observed, along with defect induced Fermi level pinning. This indicates a Schottky type contact behaviour with a barrier height of 0.41 eV. The subsequent annealing at 850 °C for 5 min resulted in the formation of a Ni2Si layer and a reversal of the band bending to 0.06 eV downward. Thus explaining the ohmic contact behaviour frequently reported for annealed n-type 3C SiC/Ni contacts.

Crystal structures of Er4Ni13C4 and UW4C4

International Nuclear Information System (INIS)

Khalili, M.M.; Bodak, O.I.; Marusin, E.P.; Pecharskaya, A.O.

1990-01-01

Crystal structures of Er 4 Ni 13 C 4 (1) (sp.gr. Cmmm, a=1.1975(4), b=1.1694(3), c=0.3856(1) nm, Z=2) and UW 4 C 4 (2) (sp.gr. P4/m, a=0.8328(8), c=0.31345(9) nm, Z=2), relating to new types are determined. Structural type (1) is a derivative of La 2 Ni 5 C 3 structure, structural type (2) is close to UCr 4 C 4 structure

Depresión en niños y niñas con cáncer

Directory of Open Access Journals (Sweden)

Yolanda del Refugio González-Hernández

2006-01-01

Full Text Available La depresión infantil existe y está presente en muchos niños y niñas hoy en día, principalmente porque se han incrementando los factores de riesgo para su aparición. Uno de estos grandes factores es la pérdida de la salud, la amenaza de daño a la propia estructura física, psicológica y social del niño o la niña. El cáncer infantil logra romper esta estructura. La presente revisión bibliográfica pretende exponer aquellos estudios que se han realizado sobre la depresión infantil, su relación con el cáncer, así como el análisis de los resultados de estudios longitudinales de sobrevivientes de cáncer infantil sobre la presencia o ausencia de secuelas psicosociales importantes que influyan en su funcionamiento actual.

Preliminary Microstructural and Microscratch Results of Ni-Cr-Fe and Cr3C2-NiCr Coatings on Magnesium Substrate

Science.gov (United States)

Istrate, B.; Munteanu, C.; Lupescu, S.; Benchea, M.; Vizureanu, P.

2017-06-01

Thermal coatings have a large scale application in aerospace and automotive field, as barriers improving wear mechanical characteristics and corrosion resistance. In present research, there have been used two types of coatings, Ni-Cr-Fe, respectively Cr3C2-NiCr which were deposited on magnesium based alloys (pure magnesium and Mg-30Y master alloy). There have been investigated the microstructural aspects through scanning electronic microscopy and XRD analysis and also a series of mechanical characteristics through microscratch and indentation determinations. The results revealed the formation of some adherent layers resistant to the penetration of the metallic indenter, the coatings did not suffer major damages. Microstructural analysis highlighted the formation of Cr3C2, Cr7C3, Cr3Ni2, Cr7Ni3, FeNi3, Cr-Ni phases. Also, the apparent coefficient of friction for Ni-Cr-Fe coatings presents superior values than Cr3C2-NiCr coatings.

Spherical NiO-C composite for anode material of lithium ion batteries

International Nuclear Information System (INIS)

Huang, X.H.; Tu, J.P.; Zhang, C.Q.; Chen, X.T.; Yuan, Y.F.; Wu, H.M.

2007-01-01

Spherical NiO-C composite was prepared by dispersing spherical NiO in glucose solution and subsequent carbonization under hydrothermal conditions at 180 o C. The microstructure and morphology of the NiO-C and NiO powders were characterized by means of X-ray diffraction (XRD) and scanning electron microscopy (SEM). The electrochemical properties of the electrodes were measured by galvanostatic charge-discharge tests, cyclic voltammetric analysis (CV), and electrochemical impedance spectroscopy (EIS). SEM images showed that the amorphous carbon not only coated on the surface but also filled the inner pores of the NiO spheres. Electrochemical tests showed that the NiO-C composite exhibited higher initial coulombic efficiency (66.6%) than NiO (56.4%), and better cycling performances. The improvement of these properties is attributed to the carbon, as it can reduce the specific surface area of porous sphere, and enhance the conductivity of porous NiO

Magnetic relaxation behaviour in Pr_2NiSi_3

International Nuclear Information System (INIS)

Pakhira, Santanu; Mazumdar, Chandan; Ranganathan, R.

2016-01-01

Time dependent isothemal remanent magnetizatin (IRM) behaviour for polycrystalline compound Pr_2NiSi_3 have been studied below its characteristic temperature. The compound undergoes slow magnetic relaxation with time. Along with competing interaction, non-magnetic atom disorder plays an important role in formation of non-equilibrium glassy like ground state for this compound.

Growth of polycrystalline Pr_2NiO_4_+_δ coating on alumina substrate by RF magnetron co-sputtering from composite targets

International Nuclear Information System (INIS)

Sediri, A.; Zaghrioui, M.; Barichard, A.; Autret, C.; Negulescu, B.; Del Campo, L.; Echegut, P.; Laffez, P.

2016-01-01

Polycrystalline Pr_2NiO_4_+_δ coatings have been deposited on alumina substrates at room temperature by RF magnetron co-sputtering from Pr and Ni metallic composite target. The mixed target's area and the sputtering conditions were optimized to reach an atomic ratio Pr/Ni of 2. A subsequent annealing, at 1050–1100 °C, allowed obtaining Pr_2NiO_4_+_δ phase after in situ high temperature x-ray diffraction study performed on as-deposited film. Microstructural analyses (SEM and AFM) revealed dense and rough microstructure. Normal spectral emittance measurements performed at 794 °C in the spectral range 400–5000 cm"-"1 showed an emissivity of ε ≈ 0.8. - Highlights: • Pr_2NiO_4_+_δ coatings deposited by RF magnetron co-sputtering • Crystallization kinetic studied by X-ray diffraction versus temperature • SEM and AFM observations showed dense and rough microstructure • Normal spectral emittance reaches to ε = 0.8 at 794 °C in the opaque zone.

Magnetic and transport properties of EuNi(Si1-xGex)3 compounds

International Nuclear Information System (INIS)

Uchima, K; Takaesu, Y; Akamine, H; Kakihana, M; Tomori, K; Uejo, T; Teruya, A; Nakamura, A; Hedo, M; Nakama, T; Yagasaki, K; Matsubayashi, K; Uwatoko, Y

2014-01-01

The magnetization M, electrical resistivity ρ, thermopower S and specific heat C of EuNi(Si 1-x Ge x ) 3 compounds have been measured at temperatures from 2 to 300 K. For the compounds of EuNi(Si 1-x Ge x ) 3 , we obtained an effective magnetic moment of μ eff ∼ 7.7 μ B , which is close to the divalent Eu value of μ eff =7.94 μ B . All compounds of EuNi(Si 1-x Ge x ) 3 order antiferromagnetically. The Néel temperature T N decreases monotonously with increasing the Ge concentration x from T N =49 K for EuNiSi 3 to T N =14 K for EuNiGe 3 . In the low temperature region below T N , anomalies corresponding to an additional magnetic phase transition into ferromagnetic state for compounds with x < 0.3, and into another antiferromagnetic for x > 0.3 were observed. The Curie temperature T C rapidly decreases with increasing x and vanishes at x ≈ 0.3. It is found that the magnetic phase transition temperatures of T N and T C in EuNi(Si 1-x Ge x ) 3 are strongly connected with the change of volume induced by the atomic substitution of Si by Ge

Energy and Rate Determinations to Activate the C-C σ-BOND of Acetone by Gaseous NI^+

Science.gov (United States)

Castleberry, Vanessa A.; Dee, S. Jason; Villarroel, Otsmar J.; Laboren, Ivanna E.; Frey, Sarah E.; Bellert, Darrin J.

2009-06-01

A unique application of a custom fabricated photodissociation spectrometer permits the determination of thermodynamic properties (activation energies), reaction rates, and mechanistic details of bare metal cation mediated C-C σ-bond activation in the gas phase. Specifically, the products and rates resulting from the unimolecular decomposition of the Ni^+Acetone (Ni^+Ac) adduct are monitored after absorption of a known amount of energy. The three dissociative products which are observed in high yield are Ni^+, Ni^+CO, and CH3CO^+. The latter two fragment ions result from the activation of a C-C σ-bond. It was found that minimally 14 000 cm^{-1} of energy must be deposited into the adduct ion to induce C-C bond breakage. Preliminary results for the Ni^+ activation of the C-C σ-bond of acetone indicate that there are (at least) two low energy reaction coordinates leading to C-C bond breakage. The lower energy pathway emerges from the doublet ground state with an upper limit to the activation energy of 14 000 cm^{-1} and reaction rate ≈0.14 molecules/μs. The higher energy path is assumed to be along the quartet reaction coordinate with a minimum activation energy of 18 800 cm^{-1} (relative to the ground state) and a slightly slower reaction rate.

Microstructure Development During Sintering of TiC-Ni3A1 Cermets

International Nuclear Information System (INIS)

Tiegs, T.N.

2001-01-01

TiC-Ni(sub 3)Al cermets are under development for application in diesel engines because of desirable physical properties and wear resistance. Powder compacts with binder contents from 30-50 vol.% were fabricated by pressureless sintering under vacuum followed by low gas pressure isostatic pressing. Increasing the Ni(sub 3)Al content improved densification when using prealloyed powders as expected. However, when the Ni(sub 3)Al was formed by in-situ reaction synthesis of Ni and NiAl, densification decreased with higher binder contents. The final microstructure consisted of a ''core-rim'' structure with TiC cores surrounded by (Ti,W)C rims. In some cases, Ni and Al were also observed in the peripheral region of the rim structure. Grain sizes of the TiC increased with binder content and temperature. Preferred orientation of the Ni(sub 3)Al binder phase was observed due to very large grain sizes on the order of millimeters

Pitting Corrosion of Ni3(Si,Ti Intermetallic Compound at Various Chloride Concentrations

Directory of Open Access Journals (Sweden)

Gadang Priyotomo

2013-10-01

Full Text Available The pitting corrosion of Ni3(Si,Ti intermetallic compound was investigated as function of chloride concentration by using electrochemical method and scanning electron microscope in sodium chloride solutions at 293 K.  In addition, the pitting corrosion of type C276 alloy was also studied under the same experimental condition for comparison.  The pitting potential obtained for the intermetallic compound decreased with increasing chloride concentration.  The specific pitting potential and pitting potential of Ni3(Si,Ti were lower than those of C276 alloy, which means that the pitting corrosion resistance of C276 alloy was higher than that of Ni3(Si,Ti.

Bimetallic Ag–Ni/C particles as cathode catalyst in AFCs (alkaline fuel cells)

International Nuclear Information System (INIS)

Song, Xingjuan; Zhang, Dongming

2014-01-01

AFCs (alkaline fuel cells) is one of the promising fuel cells, due to their low working temperature and less corrosive environment. However, decreasing the catalyst cost and improving its performance are still the challenges in its application. Transition metal as the catalyst for AFCs not only can reduce its cost, but also has great electro-catalytic efficiency. In this paper, Carbon supported Ag–Ni bimetallic catalysts with differential Ag/Ni atomic ratios were prepared by chemically reducing silver and nickel salts. Ag 3 Ni/C shows the relatively higher ORR (oxygen reduction reaction) activity among the differential Ag/Ni bimetallic particles. In order to improve the activity and stability, the catalysts were heat-treated at the temperature of 500 °C. The results indicate that the limiting current density has been improved greatly for Ag 3 Ni/C-500 °C, which is as high as 2.5× that of Ag/C. The microstructure investigation show that the non-equilibrium state of Ag–Ni alloy by heat treatment is confirmed by HRTEM (high-resolution transmission electron microscopy) images, and Ag(111) surfaces are decreased in XRD pattern, which results in the ORR activity improved and overpotential decreased. Heat treatment also has contributed to Ag–Ni/C electrochemistry stability in some degree. - Highlights: • Ag–Ni/C is applied as cathode catalyst for AFCs (alkaline fuel cells). • Ag 3 Ni/C-500 °C shows the best performance. • Non-equilibrium state of Ag–Ni alloy by heat treatment is observed. • The decreased Ag(111) surfaces are favor to improve the catalyst activity

C-Ni-Pd and CNT-Ni-Pd film's molecular and crystalline structure investigations by FTIR spectroscopy and XRD diffraction

Science.gov (United States)

Stepińska, Izabela; Czerwosz, ElŻbieta; Diduszko, Ryszard; Kozłowski, Mirosław; Wronka, Halina

2017-08-01

In this work molecular and crystalline structure of new type of nanocomposite films were investigated. These films compose of CNT decorated with palladium nanograins. They were prepared on a base of C-Ni films modified in CVD process. C-Ni nanocomposite films were obtained by PVD process and their modification by CVD leads to a growth of CNT film. CNTs-Ni or C-Ni films were treated with additional PVD process with palladium. Nickel and palladium acetate and fulleren C60 are precursors of films in PVD process. FTIR spectroscopy was used to studied the molecular structure of film in every stage of preparation . The crystalline structure of these films was studied by X-ray diffraction. SEM (scanning electron microscopy) was applied to investigate film's surface topography.

c-C5H5 on a Ni(1 1 1) surface: Theoretical study of the adsorption, electronic structure and bonding

International Nuclear Information System (INIS)

German, E.; Simonetti, S.; Pronsato, E.; Juan, A.; Brizuela, G.

2008-01-01

In the present work the ASED-MO method is applied to study the adsorption of cyclopentadienyl anion on a Ni(1 1 1) surface. The adsorption with the centre of the aromatic ring placed above the hollow position has been identified to be energetically the most favourable. The aromatic ring remains almost flat, the H atoms are tilted 17 deg. away from the metal surface. We modelled the metal surface by a two-dimensional slab of finite thickness, with an overlayer of c-C 5 H 5 - , one c-C 5 H 5 - per nine surface Ni atoms. The c-C 5 H 5 - molecule is attached to the surface with its five C atoms bonding mainly with three Ni atoms. The Ni-Ni bond in the underlying surface and the C-C bonds of c-C 5 H 5 - are weakened upon adsorption. We found that the band of Ni 5d z 2 orbitals plays an important role in the bonding between c-C 5 H 5 - and the surface, as do the Ni 6s and 6p z bands

Electronic structures of N- and C-doped NiO from first-principles calculations

International Nuclear Information System (INIS)

Long, Run; English, Niall J.; Mooney, Damian A.

2010-01-01

The large intrinsic band gap of NiO has hindered severely its potential application under visible-light irradiation. In this Letter, we have performed first-principles calculations on the electronic properties of N- and C-doped NiO to ascertain if its band gap may be narrowed theoretically. It was found that impurity bands driven by N 2p or C 2p states appear in the band gap of NiO and that some of these locate at the conduction band minimum, which leads to a significant band gap narrowing. Our results show that N-doped NiO may serve as a potential photocatalyst relative to C-doped NiO, due to the presence of some recombination centres in C-doped NiO.

Growth of polycrystalline Pr{sub 2}NiO{sub 4+δ} coating on alumina substrate by RF magnetron co-sputtering from composite targets

Energy Technology Data Exchange (ETDEWEB)

Sediri, A., E-mail: amal.sediri@univ-tours.fr [Université François-Rabelais de Tours, GREMAN UMR 7347 CNRS, IUT de Blois 15 rue de la chocolaterie CS 2903, 41029 Blois Cedex (France); Zaghrioui, M.; Barichard, A.; Autret, C.; Negulescu, B. [Université François-Rabelais de Tours, GREMAN UMR 7347 CNRS, IUT de Blois 15 rue de la chocolaterie CS 2903, 41029 Blois Cedex (France); Del Campo, L.; Echegut, P. [CNRS, UPR 3079 CEMHTI, 45071 Orléans Cedex 2 (France); Laffez, P. [Université François-Rabelais de Tours, GREMAN UMR 7347 CNRS, IUT de Blois 15 rue de la chocolaterie CS 2903, 41029 Blois Cedex (France)

2016-02-01

Polycrystalline Pr{sub 2}NiO{sub 4+δ} coatings have been deposited on alumina substrates at room temperature by RF magnetron co-sputtering from Pr and Ni metallic composite target. The mixed target's area and the sputtering conditions were optimized to reach an atomic ratio Pr/Ni of 2. A subsequent annealing, at 1050–1100 °C, allowed obtaining Pr{sub 2}NiO{sub 4+δ} phase after in situ high temperature x-ray diffraction study performed on as-deposited film. Microstructural analyses (SEM and AFM) revealed dense and rough microstructure. Normal spectral emittance measurements performed at 794 °C in the spectral range 400–5000 cm{sup -1} showed an emissivity of ε ≈ 0.8. - Highlights: • Pr{sub 2}NiO{sub 4+δ} coatings deposited by RF magnetron co-sputtering • Crystallization kinetic studied by X-ray diffraction versus temperature • SEM and AFM observations showed dense and rough microstructure • Normal spectral emittance reaches to ε = 0.8 at 794 °C in the opaque zone.

Determination of the enthalpy of formation of Ni-Al intermetallic compounds using differential scanning calorimetry technique

International Nuclear Information System (INIS)

Kubaski, Evaldo Toniolo; Capocchi, Jose Deodoro Trani; Cintho, Osvaldo Mitsuyuki

2010-01-01

The compositions Ni20Al80, Ni25Al75, Ni40Al60, Ni50Al50, Ni60Al40 and Ni75Al25 (at. %) were heated in a calibrated thermal analysis equipment. All runs were conducted at a heating rate of 10 deg C/min under a dynamic argon atmosphere. Each composition was heated until the completion of the corresponding exothermic reaction responsible for intermetallic compound formation, and, also heated to 1480 deg C. The products obtained were characterized using X ray diffraction in order to identify the intermetallic compounds that were synthesized. Moreover, the results were evaluated using variance analysis. As a result, enthalpies of formation of Ni 2 Al 3 and Ni 3 Al compounds were determined by means of this methodology. Experimental values were 167 kJ/mol and 93 kJ/mol for Ni 2 Al 3 and Ni 3 Al, respectively. The former is 18% lower than the value found on literature, while the latter is 6% greater. (author)

Effect of C particle size on the mechanism of self-propagation high-temperature synthesis in the Ni-Ti-C system

International Nuclear Information System (INIS)

Yang, Y.F.; Wang, H.Y.; Wang, J.G.; Jiang, Q.C.

2011-01-01

Highlights: → We investigated the effect of C particle size on the self-propagating high temperature reaction mechanism. → Coarse C particle size (>38 μm) resulted in the formation of prior TiC x layer between Ti and C. → Prior TiC x layer control the whole reaction of Ni-Ti-C and domain the reaction kinetics. → The selection of C particle size is the most important factor to fabricate TiC/Ni composite using Ti, C and Ni mixtures. - Abstract: Effect of C particle size on the mechanism of self-propagation high-temperature synthesis (SHS) in the Ni-Ti-C system was investigated. Fine C particle resulted in a traditional mechanism of dissolution-precipitation while coarse C particle made the reaction be controlled by a mechanism of the diffusion of C through the TiC x layer. The whole process can be described: C atoms diffusing through the TiC x layer dissolved into the Ni-Ti liquid and TiC were formed once the liquid became supersaturated. Simultaneously, the heat generated from the TiC formation made the unstable TiC x layer break up. However, with the spread of Ti-Ni liquid, a new TiC x layer was formed again at the interface between spreading liquid and C particle. This process cannot stop until all the C particles are consumed completely.

Magnetic order of Y{sub 3}NiSi{sub 3}-type R{sub 3}NiSi{sub 3} (R=Gd–DY) compounds

Energy Technology Data Exchange (ETDEWEB)

Morozkin, A.V., E-mail: morozkin@tech.chem.msu.ru [Department of Chemistry, Moscow State University, Leninskie Gory, House 1, Building 3, GSP-2, Moscow 119992 (Russian Federation); Yapaskurt, V.O. [Department of Petrology, Faculty of Geology, Moscow State University, Leninskie Gory, Moscow 119992 (Russian Federation); Nirmala, R. [Indian Institute of Technology Madras, Chennai 600036 (India); Malik, S.K.; Quezado, S. [Departamento de Física Teórica e Experimental, Universidade Federal do Rio Grande do Norte, Natal 59082-970 (Brazil); Yao, Jinlei; Mozharivskyj, Y. [Department of Chemistry and Chemical Biology, McMaster University, 1280 Main Street West, Hamilton, Ontario, Canada L8S 4M1 (Canada); Nigam, A.K. [Tata Institute of Fundamental Research, Mumbai 400005 (India); Isnard, O. [Université Grenoble Alpes, Inst NEEL, BP166, F-38042 Grenoble (France); CNRS, Institut NEEL, 25 rue des martyrs, F-38042 Grenoble (France)

2016-01-15

Magnetic measurements and neutron powder diffraction investigations on the Y{sub 3}NiSi{sub 3}-type R{sub 3}NiSi{sub 3} compounds (R=Gd, Tb, Dy) reveal their complex antiferromagnetic ordering. Magnetic measurements on Gd{sub 3}NiSi{sub 3}, Tb{sub 3}NiSi{sub 3} and Dy{sub 3}NiSi{sub 3} indicate antiferromagnetic-like transition at temperatures 260 K, 202 K and 140 K, respectively. Also, the Tb{sub 3}NiSi{sub 3} and Dy{sub 3}NiSi{sub 3} compounds show spin-reorientation transition at 132 K and 99 K, respectively. Below the spin-reorientation transition, the isothermal magnetization curves indicate the metamagnetic-like behavior of Tb{sub 3}NiSi{sub 3} and Dy{sub 3}NiSi{sub 3}. The magnetocaloric effect of Dy{sub 3}NiSi{sub 3} is calculated in terms of isothermal magnetic entropy change and it reaches a maximum value of −1.2 J/kg K and −1.1 J/kg K for a field change of 50 kOe near 146 K and 92 K, respectively. The neutron diffraction studies of Tb{sub 3}NiSi{sub 3} suggest the magnetic ordering of the Tb2 4j sublattice and no magnetic ordering of the Tb1 2a sublattice. Tb{sub 3}NiSi{sub 3} transforms from the high temperature paramagnetic state to the commensurate high-temperature a- and c-axis antiferromagnet of I′2/m magnetic space group below 250 K. Below 150 K, the high-temperature antiferromagnet transforms into the low-temperature a-, b- and c-axis antiferromagnet of I′i magnetic space group. At 1.5 K, the terbium magnetic moment in Tb2 sublattice and its a-, b- and c-axis components reach the values of M{sub Tb2}=8.2(1) μ{sub B}, M{sub aTb2}=5.9(1) μ{sub B}, M{sub bTb2}=4.3(2) μ{sub B} and M{sub cTb2}=3.7(2) μ{sub B}, respectively. - Highlights: • Gd{sub 3}NiSi{sub 3}, Tb{sub 3}NiSi{sub 3} and Dy{sub 3}NiSi{sub 3} have Neel points of 260. 202 and 140 K. • Tb{sub 3}NiSi{sub 3} and Dy{sub 3}NiSi{sub 3} show spin-reorientation transition at 132 and 99 K. • Tb{sub 3}NiSi{sub 3} exhibits the commensurate magnetic ordering of Tb2 4j sublattice

De interactie van SiC met Fe, Ni en hun legeringen

NARCIS (Netherlands)

Schiepers, R.C.J.

1991-01-01

De interactie tussen SiC en metalen gebaseerd op Fe en Ni is bestudeerd in het temperatuurtraject 700-1035°C door middel van vaste-stof-diffusiekoppels. In de koppels van SiC met Fe, Ni en hun legeringen treden hevige reakties op, die de vorming van een goede verbinding verhinderen. Door het grate

Electron microscopy characterization of Ni-Cr-B-Si-C laser deposited coatings.

Science.gov (United States)

Hemmati, I; Rao, J C; Ocelík, V; De Hosson, J Th M

2013-02-01

During laser deposition of Ni-Cr-B-Si-C alloys with high amounts of Cr and B, various microstructures and phases can be generated from the same chemical composition that results in heterogeneous properties in the clad layer. In this study, the microstructure and phase constitution of a high-alloy Ni-Cr-B-Si-C coating deposited by laser cladding were analyzed by a combination of several microscopy characterization techniques including scanning electron microscopy in secondary and backscatter imaging modes, energy dispersive spectroscopy (EDS), electron backscatter diffraction (EBSD), and transmission electron microscopy (TEM). The combination of EDS and EBSD allowed unequivocal identification of micron-sized precipitates as polycrystalline orthorhombic CrB, single crystal tetragonal Cr5B3, and single crystal hexagonal Cr7C3. In addition, TEM characterization showed various equilibrium and metastable Ni-B, Ni-Si, and Ni-Si-B eutectic products in the alloy matrix. The findings of this study can be used to explain the phase formation reactions and to tune the microstructure of Ni-Cr-B-Si-C coatings to obtain the desired properties.

DO22-(Cu,Ni)3Sn intermetallic compound nanolayer formed in Cu/Sn-nanolayer/Ni structures

International Nuclear Information System (INIS)

Liu Lilin; Huang, Haiyou; Fu Ran; Liu Deming; Zhang Tongyi

2009-01-01

The present work conducts crystal characterization by High Resolution Transmission Electron Microscopy (HRTEM) on Cu/Sn-nanolayer/Ni sandwich structures associated with the use of Energy Dispersive X-ray (EDX) analysis. The results show that DO 22 -(Cu,Ni) 3 Sn intermetallic compound (IMC) ordered structure is formed in the sandwich structures at the as-electrodeposited state. The formed DO 22 -(Cu,Ni) 3 Sn IMC is a homogeneous layer with a thickness about 10 nm. The DO 22 -(Cu,Ni) 3 Sn IMC nanolayer is stable during annealing at 250 deg. C for 810 min. The formation and stabilization of the metastable DO 22 -(Cu,Ni) 3 Sn IMC nanolayer are attributed to the less strain energy induced by lattice mismatch between the DO 22 IMC and fcc Cu crystals in comparison with that between the equilibrium DO 3 IMC and fcc Cu crystals.

Hydride Reactivity of Ni-II-X-Ni-II Entities : Mixed-Valent Hydrido Complexes and Reversible Metal Reduction

NARCIS (Netherlands)

Gehring, Henrike; Metzinger, Ramona; Herwig, Christian; Intemann, Julia; Harder, Sjoerd; Limberg, Christian

After the lithiation of PYR-H2 (PYR2-=[{NC(Me)C(H)C(Me)NC6H3(iPr)2}2(C5H3N)]2-), which is the precursor of an expanded beta-diketiminato ligand system with two binding pockets, its reaction with [NiBr2(dme)] led to a dinuclear nickel(II)bromide complex, [(PYR)Ni(mu-Br)NiBr] (1). The bridging bromide

Estimation of the Temperature-Dependent Nitrogen Solubility in Stainless Fe-Cr-Mn-Ni-Si-C Steel Melts During Processing

Science.gov (United States)

Wendler, Marco; Hauser, Michael; Sandig, Eckhard Frank; Volkova, Olena

2018-04-01

The influence of chemical composition, temperature, and pressure on the nitrogen solubility of various high alloy stainless steel grades, namely Fe-14Cr-(0.17-7.77)Mn-6Ni-0.5Si-0.03C [wt pct], Fe-15Cr-3Mn-4Ni-0.5Si-0.1C [wt pct], and Fe-19Cr-3Mn-4Ni-0.5Si-0.15C [wt pct], was studied in the melt. The temperature-dependent N-solubility was determined using an empirical approach proposed by Wada and Pehlke. The thus calculated N-concentrations overestimate the actual N-solubility of all the studied Fe-Cr-Mn-Ni-Si-C steel melts at a given temperature and pressure. Consequently, the calculation model has to be modified by Si and C because both elements are not recognized in the original equation. The addition of the 1st and 2nd order interaction parameters for Si and C to the model by Wada and Pehlke allows a precise estimation of the temperature-dependent nitrogen solubility in the liquid steel bath, and fits very well with the measured nitrogen concentrations during processing of the steels. Moreover, the N-solubility enhancing effect of Cr- and Mn-additions has been demonstrated.

Magnetic domain structure and domain-wall energy in UFe8Ni2Si2 and UFe6Ni4Si2 intermetallic compounds

International Nuclear Information System (INIS)

Wyslocki, J.J.; Suski, W.; Wochowski, K.

1994-01-01

Magnetic domain structures in the UFe 8 Ni 2 Si 2 and UFe 6 Ni 4 Si 2 compounds were studied using the powder pattern method. The domain structure observed is typical for uniaxial materials. The domain-wall energy density γ was determined from the average surface domain width D s observed on surfaces perpendicular to the easy axis as equal to 16 erg/cm 2 for UFe 8 Ni 2 Si 2 and 10 erg/cm 2 for UFe 6 Ni 4 Si 2 . Moreover, the critical diameter for single domain particle D c was calculated for the studied compounds

Effect of mechanical alloying on FeCrC reinforced Ni alloys

Energy Technology Data Exchange (ETDEWEB)

Yilmaz, S. Osman [Univ. of Namik Kemal, Tekirdag (Turkey); Teker, Tanju [Adiyaman Univ. (Turkey). Dept. of Metallurgical and Materials Engineering; Demir, Fatih [Batman Univ. (Turkey)

2016-05-01

Mechanical alloying (MA) is a powder metallurgy processing technique involving cold welding, fracturing and rewelding of powder particles in a high-energy ball mill. In the present study, the intermetallic matrix composites (IMCs) of Ni-Al reinforced by M{sub 7}C{sub 3} were produced by powder metallurgical routes via solid state reaction of Ni, Al and M{sub 7}C{sub 3} particulates by mechanical alloying processes. Ni, Al and M{sub 7}C{sub 3} powders having 100 μm were mixed, mechanical alloyed and the compacts were combusted in a furnace. The mechanically alloyed (MAed) powders were investigated by X-ray diffraction (XRD), microhardness measurement, optic microscopy (OM), scanning electron microscopy (SEM) and energy dispersive spectrometry (EDS). The presence of the carbides depressed the formation of unwanted NiAl intermetallic phases. The mechanical alloyed M{sub 7}C{sub 3} particles were unstable and decomposed partially within the matrix during alloying and sintering, and the morphology of the composites changed with the dissolution ratio of M{sub 7}C{sub 3} and sintering temperature.

Incommensurate magnetic modulations in the magnetic superconductor HoNi2B2C

International Nuclear Information System (INIS)

Schneider, M.; Zaharko, O.; Keller, L.; Allenspach, P.; Kreyssig, A.; Canfield, P.C.

2006-01-01

Full text: The borocarbide HoNi 2 B 2 C is an unconventional superconductor of particular interest, since long-range magnetism coexists and competes with superconductivity on a common energy range [1]. Our study is based on high quality single crystals of 11 B-substituted HoNi 2 B 2 C. The neutron diffraction investigations are devoted to two issues of specific relevance to HoNi 2 B 2 C. Firstly, the near re-entrant phase between 5K 2 B 2 C is more complicated than proposed so fare [2]. Furthermore we performed a spherical neutron polarimetry experiment to determine the two ICM magnetic structures of HoNi 2 B 2 C and neutron spectroscopy investigations to obtain the microscopic magnetic coupling parameters. All these studies resulted in quite a consistent and complete picture of magnetism in HoNi 2 B 2 C, however, we could not find clear evidence for a strong interaction between superconductivity and magnetism. (author)

Magnetism and superconductivity in ErNi2B2C

Indian Academy of Sciences (India)

in modulation vector and harmonic content. Studies of the vortex lattice show the presence of a 45. ◦ reorientation transition and a distorted hexagonal to square transition as a function of applied field. Further distortions of the vortex lattice occur at TN, but no changes are seen at TF. Keywords. (RE)Ni2B2C; ErNi2B2C; vortex ...

Cr Poisoning On Nd2Ni0.95Cu0.05O4+δ Cathode for Solid Oxide Fuel Cells

Directory of Open Access Journals (Sweden)

Choe Yeong-Ju

2016-06-01

Full Text Available In this study, Nd2Ni1-xCuxO4+δ (x=0, 0.05, 0.1, and 0.2 layered perovskite powders were synthesized by the glycine nitrate process (GNP and the chromium poisoning effect on the electrochemical performance of the Nd2Ni0.95Cu0.05O4+δ and La0.6Sr0.4Co0.2Fe0.8O3-δ cathodes were investigated. In the case of the LSCF cathode, the strontium chromite phase formed after the exposure of the gaseous chromium species, while there was no additional phase in the Nd2Ni0.95Cu0.05O4+δ cathode. The area specific resistance (ASR of the Nd2Ni0.95Cu0.05O4+δ cathode did not change significantly after the exposure of the gaseous chromium species at 800°C.

Tuning of superconductivity by Ni substitution into noncentrosymmetric ThC o1 -xN ixC2

Science.gov (United States)

Grant, T. W.; Cigarroa, O. V.; Rosa, P. F. S.; Machado, A. J. S.; Fisk, Z.

2017-07-01

The recently discovered noncentrosymmetric superconductor ThCoC2 was observed to show unusual superconducting behavior with a critical temperature of Tc=2.65 K . Here we investigate the effect of nickel substitution on the superconducting state in ThC o1 -xN ixC2 . Magnetization, resistivity, and heat capacity measurements demonstrate Ni substitution has a dramatic effect with critical temperature increased up to Tc=12.1 K for x =0.4 Ni concentration, which is a rather high transition temperature for a noncentrosymmetric superconductor. In addition, the unusual superconducting characteristics observed in pure ThCoC2 appear to be suppressed or tuned with Ni substitution towards a more conventional fully gapped superconductor.

One-pot synthesis of NiO/C composite nanoparticles as anode materials for lithium-ion batteries

Energy Technology Data Exchange (ETDEWEB)

Zhang, Lipeng, E-mail: lipeng.zhang@jcu.edu.au [School of Chemical Engineering, Shandong University of Technology, Zibo 255049 (China); College of Science, Technology and Engineering, James Cook University, Douglas, Queensland 4811 (Australia); Mu, Jiechen; Wang, Zhao; Li, Guomin; Zhang, Yanling [School of Chemical Engineering, Shandong University of Technology, Zibo 255049 (China); He, Yinghe, E-mail: yinghe.he@jcu.edu.au [College of Science, Technology and Engineering, James Cook University, Douglas, Queensland 4811 (Australia)

2016-06-25

Nanostructured NiO/C composite particles with controlled carbon content for lithium-ion battery anode were prepared via a one-pot hydrothermal approach and subsequent calcination in a high purity nitrogen atmosphere. The composites were composed of amorphous carbon and nanocrystalline NiO. The structure of the NiO crystals was determined with X-ray diffraction (XRD) analysis and the content of carbon was calculated from the energy dispersive spectroscopy (EDS) results. Scanning electron microscopy (SEM) images showed a relatively narrow distribution of particle size for both the neat NiO and NiO/C nanoparticles. Electrochemical performance measurements demonstrated that, after 50 cycles, NiO/C nanocomposites maintained a high reversible capacity of 585.9 mAh g{sup −1}, much higher than that of 356.1 mAh g{sup −1} of the neat NiO nanoparticles without carbon. The NiO/C nanoparticles also exhibited a remarkable discharge capacity, a high charge/discharge rate and an excellent cycle stability. The improvements can be attributed to the even carbon coating on the NiO particles, which significantly enhances the conductivity and improves the structural stability of the electrode. - Highlights: • NiO/C nanocomposite material is prepared via a one-pot hydrothermal approach. • Both NiO and NiO/C composite have a narrow particle size distribution. • Carbon in the NiO/C enhanced the conductivity and suppressed particle aggregation. • NiO/C composites maintained a reversible capacity of 585.9 mAh g{sup −1} after 50 cycles.

Hydrothermal synthesis and crystal structure of the Ni2(C4H4N2)(V4O12)(H2O)2 and Ni3(C4H4N2)3(V8O23) inorganic-organic hybrid compounds. Thermal, spectroscopic and magnetic studies of the hydrated phase

International Nuclear Information System (INIS)

Larrea, Edurne S.; Mesa, Jose L.; Pizarro, Jose L.; Arriortua, Maria I.; Rojo, Teofilo

2007-01-01

Ni 2 (C 4 H 4 N 2 )(V 4 O 12 )(H 2 O) 2 , 1, and Ni 3 (C 4 H 4 N 2 ) 3 (V 8 O 23 ), 2, have been synthesized using mild hydrothermal conditions at 170 deg. C under autogenous pressure. Both phases crystallize in the P-1 triclinic space group, with the unit-cell parameters, a=7.437(7), b=7.571(3), c=7.564(4) A, α=65.64(4), β=76.09(4), γ=86.25(3) o for 1 and a=8.566(2), b=9.117(2), c=12.619(3) A, α=71.05(2), β=83.48(4), γ=61.32(3) o for 2, being Z=2 for both compounds. The crystal structure of the three-dimensional 1 is constructed from layers linked between them through the pyrazine molecules. The sheets are formed by edge-shared [Ni 2 O 6 (H 2 O) 2 N 2 ] nickel(II) dimers octahedra and rings composed by four [V 4 O 12 ] vanadium(V) tetrahedra linked through vertices. The crystal structure of 2 is formed from vertex shared [VO 4 ] tetrahedra that give rise to twelve member rings. [NiO 4 (C 4 H 4 N 2 ) 2 ] ∞ chains, resulting from [NiO 4 N 2 ] octahedra and pyrazine molecules, give rise to a 3D skeleton when connecting to [VO 4 ] tetrahedra. Diffuse reflectance measurements of 1 indicate a slightly distorted octahedral geometry with values of Dq=880, B=980 and C=2700 cm -1 . Magnetic measurements of 1, carried out in the 5.0-300 K range, indicate the existence of antiferromagnetic couplings with a Neel temperature near to 38 K. - Graphical abstract: Crystal structure of a sheet of Ni 2 (C 4 H 4 N 2 )(V 4 O 12 )(H 2 O) 2

Facile synthesis and microwave absorbability of C@Ni–NiO core–shell hybrid solid sphere and multi-shelled NiO hollow sphere

International Nuclear Information System (INIS)

Wu, Hongjing; Wu, Guanglei; Wu, Qiaofeng; Wang, Liuding

2014-01-01

We reported the preparation of C@Ni–NiO core–shell hybrid solid spheres or multi-shelled NiO hollow spheres by combining a facile hydrothermal route with a calcination process in H 2 or air atmosphere, respectively. The synthesized C@Ni–NiO core–shell solid spheres with diameters of approximately 2–6 μm were in fact built from dense NiO nanoparticles coated by random two-dimensional metal Ni nanosheets without any visible pores. The multi-shelled NiO hollow spheres were built from particle-like ligaments and there are a lot of pores with size of several nanometers on the surface. Combined Raman spectra with X-ray photoelectron spectra (XPS), it suggested that the defects in the samples play a limited role in the dielectric loss. Compared with the other samples, the permeability of the samples calcined in H 2 and air was increased slightly and the natural resonance frequency shifted to higher frequency (7, 11 and 14 GHz, respectively), leading to an enhancement of microwave absorption property. For the sample calcined in H 2 , an optimal reflection loss less than − 10 was obtained at 7 GHz with a matching thickness of 5.0 mm. Our study demonstrated the potential application of C@Ni–NiO core–shell hybrid solid sphere or multi-shelled NiO hollow sphere as a more efficient electromagnetic (EM) wave absorber. - Highlights: • C@Ni–NiO core–shell hybrid solid sphere was synthesized by a facile method. • Multi-shelled NiO hollow sphere was synthesized by a facile method. • It suggested that the defects in the samples play a limited role in dielectric loss. • The permeability of the samples calcined in H 2 and air was increased. • Microwave absorbability of C@Ni–NiO core–shell hybrid solid sphere was investigated

Magnetic relaxation behaviour in Pr{sub 2}NiSi{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Pakhira, Santanu, E-mail: santanupakhira20006@gmail.com; Mazumdar, Chandan; Ranganathan, R. [Condensed Matter Physics Division, Saha Institute Of Nuclear Physics, 1/AF Bidhannagar, Kolkata-700064 (India)

2016-05-06

Time dependent isothemal remanent magnetizatin (IRM) behaviour for polycrystalline compound Pr{sub 2}NiSi{sub 3} have been studied below its characteristic temperature. The compound undergoes slow magnetic relaxation with time. Along with competing interaction, non-magnetic atom disorder plays an important role in formation of non-equilibrium glassy like ground state for this compound.

Effect of Carbon Content on the Microstructure and Mechanical Properties of NbC-Ni Based Cermets

Directory of Open Access Journals (Sweden)

Shuigen Huang

2018-03-01

Full Text Available The aim of this work was to correlate the overall carbon content in NbC-Ni, NbC-Ni-VC and NbC-Ni-Mo starting powders with the resulting microstructure, hardness, and fracture toughness of Ni-bonded NbC cermets. A series of NbC-Ni, NbC-Ni-VC and NbC-Ni-Mo cermets with different carbon content were prepared by conventional liquid phase sintering for 1 h at 1420 °C in vacuum. Microstructural analysis of the fully densified cermets was performed by electron probe microanalysis (EPMA to assess the effect of carbon and VC or Mo additions on the NbC grain growth and morphology. A decreased carbon content in the starting powder mixtures resulted in increased dissolution of Nb, V, and Mo in the Ni binder and a decreased C/Nb ratio in the NbC based carbide phase. The Vickers hardness (HV30 and Palmqvist indentation toughness were found to decrease significantly with an increasing carbon content in the Mo-free cermets, whereas an antagonistic correlation between hardness and toughness was obtained as a function of the Mo-content in Mo-modified NbC cermets. To obtain optimized mechanical properties, methods to control the total carbon content of NbC-Ni mixtures were proposed and the prepared cermets were investigated in detail.

Synthesis Of NiCrAlC alloys by mechanical alloying; Sintese de ligas NiCrAlC por moagem de alta energia

Energy Technology Data Exchange (ETDEWEB)

Silva, A.K.; Pereira, J.I.; Vurobi Junior, S.; Cintho, O.M., E-mail: alissonkws@gmail.co [Universidade Estadual de Ponta Grossa (UEPG), PR (Brazil)

2010-07-01

The purpose of the present paper is the synthesis of nickel alloys (NiCrAlC), which has been proposed like a economic alternative to the Stellite family Co alloys using mechanical alloying, followed by sintering heat treatment of milled material. The NiCrAlC alloys consist of a chromium carbides dispersion in a Ni{sub 3}Al intermetallic matrix, that is easily synthesized by mechanical alloying. The use of mechanical alloying enables higher carbides sizes and distribution control in the matrix during sintering. We are also investigated the compaction of the processed materials by compressibility curves. The milling products were characterized by X-ray diffraction, and the end product was featured by conventional metallography and scanning electronic microscopy (SEM), that enabled the identification of desired phases, beyond microhardness test, which has been shown comparable to alloys manufactured by fusion after heat treating. (author)

Synthesis and Characterization of Electrodeposited C-PANI-Pd-Ni Composite Electrocatalyst for Methanol Oxidation

Directory of Open Access Journals (Sweden)

S. S. Mahapatra

2014-01-01

Full Text Available Electropolymerization of aniline at the graphite electrodes was achieved by potentiodynamic method. Electrodeposition of Pd (C-PANI-Pd and Ni (C-PANI-Ni and codeposition of Pd-Ni (C-PANI-Pd-Ni microparticles into the polyaniline (PANI film coated graphite (C-PANI were carried out under galvanostatic control. The morphology and composition of the composite electrodes were obtained using scanning electron microscopy (SEM and energy dispersive X-ray analysis (EDX techniques. The electrochemical behavior and electrocatalytic activity of the electrode were characterized using cyclic voltammetry (CV, electrochemical impedance spectroscopy (EIS, and chronoamperometric (CA methods in acidic medium. The C-PANI-Pd-Ni electrode showed an improved catalytic performance towards methanol oxidation in terms of lower onset potential, higher anodic oxidation current, greater stability, lower activation energy, and lower charge transfer resistance. The enhanced electrocatalytic activity might be due to the greater permeability of C-PANI films for methanol molecules, better dispersion of Pd-Ni microparticles into the polymer matrixes, and the synergistic effects between the dispersed metal particles and their matrixes.

The complex transfer reaction (14C, 15O) on Ni, Zn and Ge targets: existence and mass of 69Ni

International Nuclear Information System (INIS)

Dessagne, P.; Bernas, M.; Langevin, M.; Pougheon, F.; Roussel, P.; Morrison, G.C.

1984-01-01

The ( 14 C, 15 O) complex transfer reaction has been studied at 72 MeV incident energy on 58 Ni, 60 Ni, 62 Ni, 64 Ni, 68 Zn, 70 Zn and 74 Ge, 76 Ge targets. Spectra and differential cross sections have been measured in a 5 0 angular range centred around a laboratory angle of 6 0 . The nucleus 69 Ni has been observed and its mass determined for the first time

How easy is CO2 fixation by M-C bond containing complexes (M = Cu, Ni, Co, Rh, Ir)?

KAUST Repository

Nolan, Steve; Cavallo, Luigi; Poater, Albert; Vummaleti, Sai V. C.; Talarico, Giovanni

2015-01-01

A comparison between different M–C bonds (M = Cu(I), Ni(II), Co(I), Rh(I) and Ir(I)) has been reported by using density functional theory (DFT) calculations to explore the role of the metal in the fixation or incorporation of CO2 into such complexes. The systems investigated are various metal based congeners of the Ir-complex 8 [(cod)(IiPr)Ir-CCPh], with a ligand scaffold based on cod and IiPr ligands (cod = 1,5-cyclooctadiene; IiPr = 1,3-bis(isopropyl)imidazol-2-ylidene). The results of this study show that the calculated CO2 insertion barriers follow the trend: Cu(I) (20.8 kcal mol−1) < Rh(I) (30.0 kcal mol−1) < Co(I) (31.3 kcal mol−1) < Ir(I) (37.5 kcal mol−1) < Ni(II) (45.4 kcal mol−1), indicating that the Cu(I) based analogue is the best CO2 fixer, while Ni(II) is the worst in the studied series.

How easy is CO2 fixation by M-C bond containing complexes (M = Cu, Ni, Co, Rh, Ir)?

KAUST Repository

Nolan, Steve

2015-11-27

A comparison between different M–C bonds (M = Cu(I), Ni(II), Co(I), Rh(I) and Ir(I)) has been reported by using density functional theory (DFT) calculations to explore the role of the metal in the fixation or incorporation of CO2 into such complexes. The systems investigated are various metal based congeners of the Ir-complex 8 [(cod)(IiPr)Ir-CCPh], with a ligand scaffold based on cod and IiPr ligands (cod = 1,5-cyclooctadiene; IiPr = 1,3-bis(isopropyl)imidazol-2-ylidene). The results of this study show that the calculated CO2 insertion barriers follow the trend: Cu(I) (20.8 kcal mol−1) < Rh(I) (30.0 kcal mol−1) < Co(I) (31.3 kcal mol−1) < Ir(I) (37.5 kcal mol−1) < Ni(II) (45.4 kcal mol−1), indicating that the Cu(I) based analogue is the best CO2 fixer, while Ni(II) is the worst in the studied series.

CALCUL DU SPECTRE DE REFLEXION DU MULTICOUCHE Ni/C DANS LE DOMAINE DES RAYONS X

Directory of Open Access Journals (Sweden)

A MEDDOUR

2000-12-01

Full Text Available Le pouvoir réflecteur d’un dioptre quelconque dans le domaine des rayons X est trop faible, mais il est toujours possible de choisir des systèmes pouvant présenter un pic de réflexion d’intensité importante autour d’une incidence caractéristique du matériau. Ce dernier est un multicouche, composé de deux couches déposées en sandwich.                 Nous avons élaboré un programme qui permet de calculer la réflexion d’un tel matériau en suivant la méthode d’Abelès dans laquelle une couche mince est représentée par une matrice carrée contenant toutes les informations nécessaires pour le calcul de la réflexion. Ce programme tient compte aussi des rugosités aux interfaces du multicouche, vue leur importante influence sur l’intensité du pic apparaissant sur le spectre de réflexion.                 L’application du programme au multicouche Ni/C a montré  l’existence d’un pic centré autour de 31.32°. Son intensité est sensible au nombre de périodes dans le multicouche, aux épaisseurs des couches minces de Ni et de C et à la taille des rugosités des interfaces Ni/C et C/Ni.

Transport properties of RCo_2B_2C with R = Dy, Ho, and Pr single

Science.gov (United States)

Duran, Alejandro; Escudero, Roberto

2002-03-01

Single crystals of (Dy, Ho, Pr)Co_2B_2C have been grown by a cold copper crucible method. Metallurgical and structural studies indicate that this borocarbide family melts incongruently and crystallizes as a derivative structure of the ThCr_2Si_2. The family accepts rare earth atoms depending on the type of transition metals used to form the compound. For instance with Ni atoms, all lanthanides ranging from the large lanthanum to lutetium ions are reported to form RNi_2B_2C single crystals, so far no single crystals have been obtained when changing Ni by Cobalt. A comparison of the structural parameters of the RCo_2B_2C with the RNiHo, Pr) compounds indicate that the atomic distance between transition metal atoms contracts with the insertion of the Co ion, resulting in an increasing of the c parameter and decreasing volume. Several recent reports published in the current literature related on the physical properties of RCo_2B_2C (R = rare earth metals and Y) have been only performed on polycrystalline samples, they commonly contain small amounts of second phases. High quality single crystals are necessaries in order to better understand the physical properties, such as anisotropy in the transport and in the magnetic properties. In this report we show magnetic susceptibility and resistivity measurements performed in single crystals in the ab-plane and c direction for 2 - 320 K temperature range for the three single crystals of (Dy, Ho, Pr)Co_2B_2C.

Isothermal Reaction of NiO Powder with Undiluted CH4 at 1000 K to 1300 K (727 °C to 1027 °C)

Science.gov (United States)

Altay, Melek Cumbul; Eroglu, Serafettin

2017-08-01

In this study, isothermal reaction behavior of loose NiO powder in a flowing undiluted CH4 atmosphere at the temperature range 1000 K to 1300 K (727 °C to 1027 °C) is investigated. Thermodynamic analyses at this temperature range revealed that single phase Ni forms at the input n_{CH}_{4}^{o} + n_{NiO}^{o}) (n_{CH}_{4}^{{o} + n_{NiO}^{o}) mole fractions ( X_{CH}_{4} ) between 0.2 and 0.5. It was also predicted that free C co-exists with Ni at X_{{{{CH}}_{ 4} }} values higher than 0.5. The experiments were carried out as a function of temperature, time, and CH4 flow rate. Mass measurement, XRD and SEM-EDX were used to characterize the products at various stages of the reaction. At 1200 K and 1300 K (927 °C and 1027 °C), the reaction of NiO with undiluted CH4 essentially consisted of two successive distinct stages: NiO reduction and pyrolytic C deposition on pre-reduced Ni particles. At 1200 K (927 °C), 1100 K (827 °C), and 1000 K (727 °C), complete oxide reduction was observed within 7.5, 17.5, and 45 minutes, respectively. It was suggested that NiO was essentially reduced to Ni by a CH4 decomposition product, H2. Possible reactions leading to NiO reduction were suggested. An attempt was made to describe the NiO reduction kinetics using nucleation-growth and geometrical contraction models. It was observed that the extent of NiO reduction and free C deposition increased with the square root of CH4 flow rate as predicted by a mass transport theory. A mixed controlling mechanism, partly chemical kinetics and partly external gaseous mass transfer, was responsible for the overall reaction rate. The present study demonstrated that the extent of the reduction can be determined quantitatively using the XRD patterns and also using a formula theoretically derived from the basic XRD data.

Glucose- and Cellulose-Derived Ni/C-SO3H Catalysts for Liquid Phase Phenol Hydrodeoxygenation

Energy Technology Data Exchange (ETDEWEB)

Kasakov, Stanislav; Zhao, Chen; Barath, Eszter; Chase, Zizwe A.; Fulton, John L.; Camaioni, Donald M.; Vjunov, Aleksei; Shi, Hui; Lercher, Johannes A.

2015-01-19

Sulfonated carbons were explored as functionalized supports for Ni nanoparticles to hydrodeoxygenate (HDO) phenol. Both hexadecane and water were used as solvents. The dual-functional Ni catalysts supported on sulfonated carbon (Ni/C-SO3H) showed high rates for phenol hydrodeoxygenation in liquid hexadecane, but not in water. Glucose and cellulose were precursors to the carbon supports. Changes in the carbons resulting from sulfonation of the carbons resulted in variations of carbon sheet structures, morphologies and the surface concentrations of acid sites. While the C-SO3H supports were active for cyclohexanol dehydration in hexadecane and water, Ni/C-SO3H only catalyzed the reduction of phenol to cyclohexanol in water. The state of 3 – 5 nm grafted Ni particles was analyzed by in situ X-ray absorption spectroscopy. The results show that the metallic Ni was rapidly formed in situ without detectable leaching to the aqueous phase, suggesting that just the acid functions on Ni/C-SO3H are inhibited in presence of water. Using in situ IR spectroscopy, it was shown that even in hexadecane, phenol HDO is limited by the dehydration step. Thus, phenol HDO catalysis was further improved by physically admixing C-SO3H with the Ni/C-SO3H catalyst to balance the two catalytic functions. The minimum addition of 7 wt.% C-SO3H to the most active of the Ni/C-SO3H catalysts enabled nearly quantitative conversion of phenol and the highest selectivity (90%) towards cyclohexane in 6 h, at temperatures as low as 473 K, suggesting that the proximity to Ni limits the acid properties of the support.

New quaternary indides RE{sub 7}Ni{sub 5-x}Ge{sub 3+x}In{sub 6} (RE = La, Nd, Sm)

Energy Technology Data Exchange (ETDEWEB)

Dominyuk, Nataliya [Lviv Univ. (Ukraine). Dept. of Inorganic Chemistry; Muenster Univ. (Germany). Inst. fuer Anorganische und Analytische Chemie; Zaremba, Vasyl I. [Lviv Univ. (Ukraine). Dept. of Inorganic Chemistry; Poettgen, Rainer [Muenster Univ. (Germany). Inst. fuer Anorganische und Analytische Chemie

2011-04-15

The quaternary indides RE{sub 7}Ni{sub 5-x}Ge{sub 3+x}In{sub 6} (RE = La,Nd, Sm) were synthesized from the elements by arc-melting. Single crystals were grown by slow cooling of the polycrystalline samples. The structures were characterized by powder and single-crystal X-ray diffraction: Ce{sub 7}Ni{sub 4.73}Ge{sub 3.27}In{sub 6} type, P6/m, Z = 1, a = 1147.05(9), c = 426.82(4) pm, wR2 = 0.0652, 528 F{sup 2} values for La{sub 7}Ni{sub 4.46}Ge{sub 3.54}In{sub 6}, a = 1134.5(7), c = 407.1(7) pm, wR2 = 0.0419, 441 F{sup 2} values for Nd{sub 7}Ni{sub 4.91}Ge{sub 3.09}In{sub 6}, and a = 1133.5(2), c = 404.3(1) pm, wR2 = 0.0619, 498 F{sup 2} values for Sm{sub 7}Ni{sub 4.31}Ge{sub 3.69}In{sub 6}, with 25 parameters per refinement. Characteristic features of the RE{sub 7}Ni{sub 5-x}Ge{sub 3+x}In{sub 6} structures are hexagonal, AlB{sub 2}-related prisms around the RE1 atoms and a tricapped, trigonalprismatic coordination of the nickel atoms. (orig.)

Superstructure formation in PrNi_2Al_3 and ErPd_2Al_3

International Nuclear Information System (INIS)

Eustermann, Fabian; Hoffmann, Rolf-Dieter; Janka, Oliver; Oldenburg Univ.

2017-01-01

The intermetallic phase ErPd_2Al_3 was obtained by arc-melting of the elements and subsequent annealing for crystal growth. The sample was studied by X-ray diffraction on powders and single crystals. The structure of ErPd_2Al_3 was refined from X-ray diffraction data and revealed a superstructure of PrNi_2Al_3 - a CaCu_5 derivative (P6/m, a=1414.3(1), c=418.87(3) pm wR=0.0820, 1060 F"2 values, 48 variables). The same superstructure was subsequently found for PrNi_2Al_3 (P6/m, a=1407.87(4), c=406.19(2) pm, wR=0.0499, 904 F"2 values, 47 variables). In the crystal structure, the aluminium and transition metal atoms form a polyanionic network according to [T_2Al_3]"δ"-, while rare earth atoms fill cavities within the networks. They are coordinated by six transition metal and twelve aluminum atoms. In contrast to the PrNi_2Al_3 type structure reported so far, two crystallographic independent rare-earth sites are found of which one (1b) is shifted by 1/2 z, causing a distortion in the structure along with a recoloring of the T and Al atoms in the network.

Anti-Invar properties and magnetic order in fcc Fe-Ni-C alloy

International Nuclear Information System (INIS)

Nadutov, V.M.; Kosintsev, S.G.; Svystunov, Ye.O.; Garamus, V.M.; Willumeit, R.; Eckerlebe, H.; Ericsson, T.; Annersten, H.

2011-01-01

Anti-Invar effect was revealed in the fcc Fe-25.3%Ni-0.73%C (wt%) alloy, which demonstrates high values of thermal expansion coefficient (TEC) (15-21)x10 -6 K -1 accompanied by almost temperature-insensitive behavior in temperature range of 122-525 K. Alloying with carbon considerably expanded the low temperature range of anti-Invar behavior in fcc Fe-Ni-based alloy. The Curie temperature of the alloy T C =195 K was determined on measurements of temperature dependences of magnetic susceptibility and saturation magnetization. The Moessbauer and small-angle neutron scattering (SANS) experiments on the fcc Fe-25.3%Ni-(0.73-0.78)%C alloys with the varying temperatures below and above the Curie point and in external magnetic field of 1.5-5 T were conducted. Low value of the Debye temperature Θ D =180 K was estimated using the temperature dependence of the integral intensity of Moessbauer spectra for specified temperature range. The inequality B eff =(0.7-0.9)B ext was obtained in external field Moessbauer measurement that points to antiferromagnetically coupled Fe atoms, which have a tendency to align their spins perpendicular to B ext . Nano length scale magnetic inhomogeneities nearby and far above T C were revealed, which assumed that it is caused by mixed antiferromagnetically and ferromagnetically coupled Fe atom spins. The anti-Invar behavior of Fe-Ni-C alloy is explained in terms of evolution of magnetic order with changing temperature resulting from thermally varied interspin interaction and decreasing stiffness of interatomic bond. - Highlights: → Anti-Invar effect was revealed in the fcc Fe-25.3%Ni-0.73%C (wt%) alloy. → Carbon expanded the temperature range of anti-Invar behavior in Fe-Ni-based alloy. → Moessbauer data point to mixed interspin interaction and low the Dedye temperature. → The SANS experiments reveal nano length scale magnetic inhomogeneities ≤6 nm. → Anti-Invar behavior of Fe-Ni-C alloy explained by thermally varied magnetic order.

Microstructure and morphology of powder particles TiC-NiCr, synthesized in plasma jet, at high-energy actions on components of initial composition Ti-C-NiCr

Science.gov (United States)

Solonenko, Oleg P.; Smirnov, Andrey V.; Chesnokov, Anton E.

2017-10-01

The results of experiments on in-situ synthesis of the microspherical, in particular hollow, cermet powder TiC- 30vol.%NiCr at processing of the Ti-C-NiCr agglomerates in argon-helium plasma jet flowing out into controlled atmosphere are presented. Preparation of the agglomerates consisted of the following stages: (i) high-energy treatment of the initial powders Ti and NiCr in planetary mill with their subsequent uniform mixing with glass black powder, (ii) preparation of dough from mechanically mixed powders and binder, and their granulation using the extrusion method, (iii) drying and classification of granules by the sizes.

Internal carbonitriding behavior of Ni-V, Ni-Cr, and Ni-3Nb alloys

International Nuclear Information System (INIS)

Allen, A.T.; Douglass, D.L.

1999-01-01

Ni-2V, Ni-5V, Ni-12V, Ni-10Cr, Ni-20Cr, and Ni-3Nb alloys were carbonitrided in C 3 H 6 and NH 3 gas mixtures (bal H 2 ) over the range 700--1,000 C. Carbonitridation of Ni-12V and Ni-20Cr in C 3 H 6 /NH 3 /H 2 (1.5/1.5/97 v/o) and (1.5/10/88.5 v/o) produced duplex subscales consisting of near-surface nitrides with underlying carbides. Growth of each zone obeyed the parabolic rate law under most conditions. The presence of carbon generally did not effect the depth of the nitride zones compared to nitriding the alloys in NH 3 /H 2 (10/90 v/o). However, at 700 C, the nitride zones were deeper in the carbonitrided Ni-V alloys and Ni-20Cr. The presence of nitrogen generally increased the depth of the carbide zones in Ni-12V and Ni-20Cr compared to carburizing these alloys in C 3 H 6 /H 2 (1.5/98.5 v/o). VN, CrN, and NbN formed in Ni-V, Ni-Cr, and Ni-Nb alloys, respectively, whereas the underlying carbide layers contained V 4 C 3 in Ni-12V, Cr 3 C 2 above a zone of Cr 7 C 3 in Ni-20Cr, and NbC in Ni-3Nb. The solubilities and diffusivities of nitrogen and carbon in nickel were determined. Nitrogen and carbon each exhibited retrograde solubility with temperature in pure Ni in both carbonitriding environments. Nitrogen diffusion in nickel was generally lower in each carbonitriding mixture compared to nitrogen diffusion in a nitriding environment, except at 700 C when nitrogen diffusion was higher. Carbon diffusion in nickel was generally higher in the carbonitriding environments compared to carbon diffusion in a carburizing environment

The analysis of adhesion failure between Ni-coating and sintered NdFeB substrate

Energy Technology Data Exchange (ETDEWEB)

Hengxiu, Y; Yong, D; Zhenlun, S, E-mail: yanghengxiu@nimte.ac.cn [Ningbo Institute of Materials Technology and Engineering, Chinese Academy of Sciences, 315201 (China)

2011-01-01

Ni-coating was widely used to protect the sintered NdFeB magnet from corrosion by Watt electro-deposition solution. However, the protection failure always occurs due to poor adhesion strength between Ni-coating and NdFeB substrate. In present work, the adhesion strength of the Ni-coating on NdFeB substrate was measured by vertical tensile method to strip Ni-coating from NdFeB substrate. The results revealed that the adhesion failure was occurred in the side of the NdFeB substrate due to a weak zone sometimes shown cracks located inside of NdFeB substrate, rather than in the interface between Ni-coating and NdFeB substrate. Comparing with cross section morphology of NdFeB magnet after pretreatment, it is concluded that the crack could be formed during the electro-deposition process. The effect of the pH value of bath on adhesion strength indicated that the crack could be induced due to electrochemical hydrogenation of NdFeB substrate during electro-deposition.

Glucose- and cellulose-derived Ni/C-SO3H catalysts for liquid phase phenol hydrodeoxygenation.

Science.gov (United States)

Kasakov, Stanislav; Zhao, Chen; Baráth, Eszter; Chase, Zizwe A; Fulton, John L; Camaioni, Donald M; Vjunov, Aleksei; Shi, Hui; Lercher, Johannes A

2015-01-19

Sulfonated carbons were explored as functionalized supports for Ni nanoparticles to hydrodeoxygenate (HDO) phenol. Both hexadecane and water were used as solvents. The dual-functional Ni catalysts supported on sulfonated carbon (Ni/C-SO3H) showed high rates for phenol hydrodeoxygenation in liquid hexadecane, but not in water. Glucose and cellulose were precursors to the carbon supports. Changes in the carbons resulting from sulfonation of the carbons resulted in variations of carbon sheet structures, morphologies and the surface concentrations of acid sites. While the C-SO3H supports were active for cyclohexanol dehydration in hexadecane and water, Ni/C-SO3H only catalysed the reduction of phenol to cyclohexanol in water. The state of 3-5 nm grafted Ni particles was analysed by in situ X-ray absorption spectroscopy. The results show that the metallic Ni was rapidly formed in situ without detectable leaching to the aqueous phase, suggesting that just the acid functions on Ni/C-SO3H are inhibited in the presence of water. Using in situ IR spectroscopy, it was shown that even in hexadecane, phenol HDO is limited by the dehydration step. Thus, phenol HDO catalysis was further improved by physically admixing C-SO3H with the Ni/C-SO3H catalyst to balance the two catalytic functions. The minimum addition of 7 wt % C-SO3H to the most active of the Ni/C-SO3H catalysts enabled nearly quantitative conversion of phenol and the highest selectivity (90%) towards cyclohexane in 6 h, at temperatures as low as 473 K, suggesting that the proximity to Ni limits the acid properties of the support. © 2015 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

Effect of Nano-TiC Dispersed Particles and Electro-Codeposition Parameters on Morphology and Structure of Hybrid Ni/TiC Nanocomposite Layers.

Science.gov (United States)

Benea, Lidia; Celis, Jean-Pierre

2016-04-06

This research work describes the effect of dispersed titanium carbide (TiC) nanoparticles into nickel plating bath on Ni/TiC nanostructured composite layers obtained by electro-codeposition. The surface morphology of Ni/TiC nanostructured composite layers was characterized by scanning electron microscopy (SEM). The composition of coatings and the incorporation percentage of TiC nanoparticles into Ni matrix were studied and estimated by using energy dispersive X-ray analysis (EDX). X-ray diffractometer (XRD) has been applied in order to investigate the phase structure as well as the corresponding relative texture coefficients of the composite layers. The results show that the concentration of nano-TiC particles added in the nickel electrolyte affects the inclusion percentage of TiC into Ni/TiC nano strucured layers, as well as the corresponding morphology, relative texture coefficients and thickness indicating an increasing tendency with the increasing concentration of nano-TiC concentration. By increasing the amount of TiC nanoparticles in the electrolyte, their incorporation into nickel matrix also increases. The hybrid Ni/nano-TiC composite layers obtained revealed a higher roughness and higher hardness; therefore, these layers are promising superhydrophobic surfaces for special application and could be more resistant to wear than the pure Ni layers.

Effect of Nano-TiC Dispersed Particles and Electro-Codeposition Parameters on Morphology and Structure of Hybrid Ni/TiC Nanocomposite Layers

Directory of Open Access Journals (Sweden)

Lidia Benea

2016-04-01

Full Text Available This research work describes the effect of dispersed titanium carbide (TiC nanoparticles into nickel plating bath on Ni/TiC nanostructured composite layers obtained by electro-codeposition. The surface morphology of Ni/TiC nanostructured composite layers was characterized by scanning electron microscopy (SEM. The composition of coatings and the incorporation percentage of TiC nanoparticles into Ni matrix were studied and estimated by using energy dispersive X-ray analysis (EDX. X-ray diffractometer (XRD has been applied in order to investigate the phase structure as well as the corresponding relative texture coefficients of the composite layers. The results show that the concentration of nano-TiC particles added in the nickel electrolyte affects the inclusion percentage of TiC into Ni/TiC nano strucured layers, as well as the corresponding morphology, relative texture coefficients and thickness indicating an increasing tendency with the increasing concentration of nano-TiC concentration. By increasing the amount of TiC nanoparticles in the electrolyte, their incorporation into nickel matrix also increases. The hybrid Ni/nano-TiC composite layers obtained revealed a higher roughness and higher hardness; therefore, these layers are promising superhydrophobic surfaces for special application and could be more resistant to wear than the pure Ni layers.

Cysteine 295 indirectly affects Ni coordination of carbon monoxide dehydrogenase-II C-cluster

Energy Technology Data Exchange (ETDEWEB)

Inoue, Takahiro; Takao, Kyosuke; Yoshida, Takashi [Division of Applied Biosciences, Graduate School of Agriculture, Kyoto University, Kyoto 606-8502 (Japan); Wada, Kei [Organization for Promotion of Tenure Track, University of Miyazaki, Miyazaki 889-1692 (Japan); Daifuku, Takashi; Yoneda, Yasuko [Division of Applied Biosciences, Graduate School of Agriculture, Kyoto University, Kyoto 606-8502 (Japan); Fukuyama, Keiichi [Department of Biological Sciences, Graduate School of Science, Osaka University, Toyonaka, Osaka 560-0043 (Japan); Sako, Yoshihiko, E-mail: sako@kais.kyoto-u.ac.jp [Division of Applied Biosciences, Graduate School of Agriculture, Kyoto University, Kyoto 606-8502 (Japan)

2013-11-08

Highlights: •CODH-II harbors a unique [Ni-Fe-S] cluster. •We substituted the ligand residues of Cys{sup 295} and His{sup 261}. •Dramatic decreases in Ni content upon substitutions were observed. •All substitutions did not affect Fe-S clusters assembly. •CO oxidation activity was decreased by the substitutions. -- Abstract: A unique [Ni–Fe–S] cluster (C-cluster) constitutes the active center of Ni-containing carbon monoxide dehydrogenases (CODHs). His{sup 261}, which coordinates one of the Fe atoms with Cys{sup 295}, is suggested to be the only residue required for Ni coordination in the C-cluster. To evaluate the role of Cys{sup 295}, we constructed CODH-II variants. Ala substitution for the Cys{sup 295} substitution resulted in the decrease of Ni content and didn’t result in major change of Fe content. In addition, the substitution had no effect on the ability to assemble a full complement of [Fe–S] clusters. This strongly suggests Cys{sup 295} indirectly and His{sup 261} together affect Ni-coordination in the C-cluster.

Cysteine 295 indirectly affects Ni coordination of carbon monoxide dehydrogenase-II C-cluster

International Nuclear Information System (INIS)

Inoue, Takahiro; Takao, Kyosuke; Yoshida, Takashi; Wada, Kei; Daifuku, Takashi; Yoneda, Yasuko; Fukuyama, Keiichi; Sako, Yoshihiko

2013-01-01

Highlights: •CODH-II harbors a unique [Ni-Fe-S] cluster. •We substituted the ligand residues of Cys 295 and His 261 . •Dramatic decreases in Ni content upon substitutions were observed. •All substitutions did not affect Fe-S clusters assembly. •CO oxidation activity was decreased by the substitutions. -- Abstract: A unique [Ni–Fe–S] cluster (C-cluster) constitutes the active center of Ni-containing carbon monoxide dehydrogenases (CODHs). His 261 , which coordinates one of the Fe atoms with Cys 295 , is suggested to be the only residue required for Ni coordination in the C-cluster. To evaluate the role of Cys 295 , we constructed CODH-II variants. Ala substitution for the Cys 295 substitution resulted in the decrease of Ni content and didn’t result in major change of Fe content. In addition, the substitution had no effect on the ability to assemble a full complement of [Fe–S] clusters. This strongly suggests Cys 295 indirectly and His 261 together affect Ni-coordination in the C-cluster

C@Fe 3 O 4 /NTA-Ni magnetic nanospheres purify histidine-tagged ...

African Journals Online (AJOL)

This study reports synthesis of Ni-nitrilotriacetic acid (Ni-NTA) modified carbon nanospheres containing magnetic Fe3O4 particles (C@Fe3O4), which can act as a general tool to separate and purify histidine-tagged fetidin. In this experiment, C nanospheres are prepared from glucose using the hydrothermal process, ...

Using DR52c/Ni2+ mimotope tetramers to detect Ni2+ reactive CD4+ T cells in patients with joint replacement failure.

Science.gov (United States)

Zhang, Yan; Wang, Yang; Anderson, Kirsten; Novikov, Andrey; Liu, Zikou; Pacheco, Karin; Dai, Shaodong

2017-09-15

T cell mediated hypersensitivity to nickel (Ni 2+ ) is one of the most common causes of allergic contact dermatitis. Ni 2+ sensitization may also contribute to the failure of Ni 2+ containing joint implants, and revision to non-Ni 2+ containing hardware can be costly and debilitating. Previously, we identified Ni 2+ mimotope peptides, which are reactive to a CD4 + T cell clone, ANi2.3 (Vα1, Vβ17), isolated from a Ni 2+ hypersensitive patient with contact dermatitis. This T cell is restricted to the major histocompatibility complex class II (MHCII) molecule, Human Leukocyte Antigen (HLA)-DR52c (DRA, DRB3*0301). However, it is not known if Ni 2+ induced T cell responses in sensitized joint replacement failure patients are similar to subjects with Ni 2+ induced contact dermatitis. Here, we generated DR52c/Ni 2+ mimotope tetramers, and used them to test if the same Ni 2+ T cell activation mechanism could be generalized to Ni 2+ sensitized patients with associated joint implant failure. We confirmed the specificity of these tetramers by staining of ANi2.3T cell transfectomas. The DR52c/Ni 2+ mimotope tetramer detected Ni 2+ reactive CD4 + T cells in the peripheral blood mononuclear cells (PBMC) of patients identified as Ni 2+ sensitized by patch testing and a positive Ni 2+ LPT. When HLA-typed by a DR52 specific antibody, three out of four patients were DR52 positive. In one patient, Ni 2+ stimulation induced the expansion of Vβ17 positive CD4 + T cells from 0.8% to 13.3%. We found that the percentage of DR52 positivity and Vβ17 usage in Ni 2+ sensitized joint failure patients are similar to Ni sensitized skin allergy patients. Ni 2+ independent mimotope tetramers may be a useful tool to identify the Ni 2+ reactive CD4 + T cells. Copyright © 2017 Elsevier Inc. All rights reserved.

Nanocrystalline electrodeposited Ni-Mo-C cathodes for hydrogen production

International Nuclear Information System (INIS)

Hashimoto, K.; Sasaki, T.; Meguro, S.; Asami, K.

2004-01-01

Tailoring active nickel alloy cathodes for hydrogen evolution in a hot concentrated hydroxide solution was attempted by electrodeposition. The carbon addition to Ni-Mo alloys decreased the nanocrystalline grain size and remarkably enhanced the activity for hydrogen evolution, changing the mechanism of hydrogen evolution. The Tafel slope of hydrogen evolution was about 35 mV per decade. This suggested that the rate-determining step is desorption of adsorbed hydrogen atoms by recombination. As was distinct from the binary Ni-Mo alloys, after open circuit immersion, the overpotential, that is, the activity of nanocrystalline Ni-Mo-C alloys for hydrogen evolution was not changed, indicating the sufficient durability in the practical electrolysis

Structural, magnetic and electric properties of Nd and Ni co-doped BiFeO3 materials

Directory of Open Access Journals (Sweden)

Dao Viet Thang

2017-09-01

Full Text Available Multiferroic Bi1−xNdxFe0.975Ni0.025O3 (x = 0.00, 0.05, 0.10, 0.125, and 0.15 (BNFNO and BiFeO3 (BFO materials were synthesized by a sol-gel method. Crystal structure, ferromagnetic and ferroelectric properties of the as-synthesized materials were investigated. Results showed that Nd3+ and Ni2+ co-doping affected to the electrical leakage, enhanced ferroelectric polarization and magnetization of BiFeO3. Co-doped sample with 12.5 mol% of Nd3+ and 2.5 mol% of Ni2+ exhibited an enhancement in both ferromagnetism and ferroelectric properties up to MS ~ 0.528 emu/g and PS ~ 18.35 μC/cm2 with applied electric field at 5 kV/cm, respectively. The origins of ferromagnetism and ferroelectricity enhancement were discussed in the paper.

Preparation and mechanical properties of in situ TiC{sub x}–Ni (Si, Ti) alloy composites

Energy Technology Data Exchange (ETDEWEB)

Wang, Wenjuan [Institute of Materials Science and Engineering, School of Mechanical, Electronic and Control Engineering, Beijing Jiaotong University, Beijing 100044 (China); Zhai, Hongxiang, E-mail: hxzhai@sina.com [Institute of Materials Science and Engineering, School of Mechanical, Electronic and Control Engineering, Beijing Jiaotong University, Beijing 100044 (China); Chen, Lin; Huang, Zhenying [Institute of Materials Science and Engineering, School of Mechanical, Electronic and Control Engineering, Beijing Jiaotong University, Beijing 100044 (China); Bei, Guoping; Baumgärtner, Christoph; Greil, Peter [Department of Materials Science (Glass and Ceramics), University of Erlangen-Nuernberg, Martensstr. 5, 91058 Erlangen (Germany)

2014-10-20

Novel in situ TiC{sub x} reinforced Ni (Si, Ti) alloy composites with superior mechanical properties were prepared at 1250 °C for 30 min by pressureless sintering Ti{sub 3}SiC{sub 2} (10 and 20 vol%) and Ni as precursors. The Ti{sub 3}SiC{sub 2} particles decomposed into substoichiometric TiC{sub x} phase, while the additional Si and partial Ti atoms derived from Ti{sub 3}SiC{sub 2} diffused into Ni matrix to form Ni (Si, Ti) alloy. The in situ formed TiC{sub x} phases are mainly dispersed on the grain boundaries of the Ni (Si, Ti) alloying, forming a strong skeleton and refining the microstructures of the metal matrix. The hardness, the yield stress σ{sub 0.2%} and ultimate compressive strength of 20.6 vol%TiC{sub x}–Ni(Si, Ti) composite can reach 2.15±0.04 GPa, 466.8±55.8 MPa and 733.3±78.4 MPa, respectively. The enhanced mechanical properties of TiC{sub x}–Ni(Si, Ti) composites are due to the in situ formation of TiC{sub x} skeleton, the refined microstructures of Ni (Si, Ti) alloys and solid solution effects as well as good wettability between TiC{sub x} and Ni (Si, Ti) matrix.

Microstructure and kinetics of a functionally graded NiTi-TiC x composite produced by combustion synthesis

International Nuclear Information System (INIS)

Burkes, Douglas E.; Moore, John J.

2007-01-01

Production of a NiTi-TiC x functionally graded material (FGM) composite is possible through use of a combustion synthesis (CS) reaction employing the propagating mode (SHS). The NiTi-TiC x FGM combines the well-known and understood superelastic and shape memory capabilities of NiTi with the high hardness, wear and corrosion resistance of TiC x . The material layers were observed as functionally graded both in composition and porosity with distinct interfaces, while still maintaining good material interaction and bonding. XRD of the FGM composite revealed the presence of TiC x with equi-atomic NiTi and minor NiTi 2 and NiTi 3 phases. The TiC x particle size decreased with increasing NiTi content. Microindentation performed across the length of the FGM revealed a decrease in hardness as the NiTi content increased

DO{sub 22}-(Cu,Ni){sub 3}Sn intermetallic compound nanolayer formed in Cu/Sn-nanolayer/Ni structures

Energy Technology Data Exchange (ETDEWEB)

Liu Lilin [School of Physics and Engineering, Sun Yat-Sen University, Guangzhou 510275 (China); Huang, Haiyou [Department of Mechanical Engineering, Hong Kong University of Science and Technology (HKUST) (Hong Kong); Hong Kong - Beijing Joint Research Center, HKUST Fok Ying Tung Graduate School, Nansha, Guangzhou (China); Fu Ran; Liu Deming [ASM Assembly Automation Ltd. (Hong Kong); Zhang Tongyi, E-mail: mezhangt@ust.h [Department of Mechanical Engineering, Hong Kong University of Science and Technology (HKUST) (Hong Kong); Hong Kong - Beijing Joint Research Center, HKUST Fok Ying Tung Graduate School, Nansha, Guangzhou (China)

2009-11-03

The present work conducts crystal characterization by High Resolution Transmission Electron Microscopy (HRTEM) on Cu/Sn-nanolayer/Ni sandwich structures associated with the use of Energy Dispersive X-ray (EDX) analysis. The results show that DO{sub 22}-(Cu,Ni){sub 3}Sn intermetallic compound (IMC) ordered structure is formed in the sandwich structures at the as-electrodeposited state. The formed DO{sub 22}-(Cu,Ni){sub 3}Sn IMC is a homogeneous layer with a thickness about 10 nm. The DO{sub 22}-(Cu,Ni){sub 3}Sn IMC nanolayer is stable during annealing at 250 deg. C for 810 min. The formation and stabilization of the metastable DO{sub 22}-(Cu,Ni){sub 3}Sn IMC nanolayer are attributed to the less strain energy induced by lattice mismatch between the DO{sub 22} IMC and fcc Cu crystals in comparison with that between the equilibrium DO{sub 3} IMC and fcc Cu crystals.

Neutron diffraction studies of magnetic ordering in superconducting ErNi2B2C and TmNi2B2C in an applied magnetic field

DEFF Research Database (Denmark)

Toft, Katrine Nørgaard

The field-induced magnetic structures of ErNi2B2C and TmNi2B2C in are especially interesting because the field suppresses the superconducting order parameter and therefore the magnetic properties can be studied while varying the strength ofsuperconductivity. ErNi2B2C: For magnetic fields along all.......483,0,0). The appearance of the QN phase wasinitially believed to be caused by the suppression of superconductivity. This suppression should make it favorable to create a magnetic order with a Q-vector determined by the maximum in the magnetic susceptibility at the Fermi surface nesting vector QN.The phase diagram...... three symmetry directions, the observed magnetic structures have a period corresponding to the Fermi surface nesting structure. The phase diagrams present all the observed magnetic structures.Two results remain unresolved: 1. When applying the magnetic field along [010], the minority domain (QNB = (0,Q...

Charge transfer effects in electrocatalytic Ni-C revealed by x-ray photoelectron spectroscopy

Energy Technology Data Exchange (ETDEWEB)

Haslam, G. E.; Chin, X.-Y.; Burstein, G. T. [Department of Materials Science and Metallurgy, University of Cambridge, Pembroke St., Cambridge CB2 3QZ (United Kingdom); Sato, K.; Mizokawa, T. [Department of Complexity Science and Engineering, University of Tokyo, 5-1-5 Kashiwanoha, Chiba 277-8651 (Japan)

2012-06-04

Binary Ni-C thin-film alloys, which have been shown to be passive against corrosion in hot sulphuric acid solution whilst also being electrocatalytically active, were investigated by XPS to determine the oxidation state of the metal and carbon components. The Ni component produces a Ni 2p spectrum similar to that of metallic nickel (i.e., no oxidation occurs) but with a 0.3 eV shift to higher binding energy (BE) due to electron donation to the carbon matrix. The C 1s peak shows a shift to lower BE by accepting electrons from the Ni nanocrystals. A cluster-model analysis of the observed Ni 2p spectrum is consistent with the electron transfer from the nickel to the carbon.

Crystal structure of the Ce2Ni2Zn15 compound

International Nuclear Information System (INIS)

Opainich, I.M.; Pavlyuk, V.V.; Bodak, O.I.; Cherny, R.; Yvon, K.

1996-01-01

A structure of a new ternary compound of the composition Ce2Ni2Zn15 (sp.gr.R3-barm,a=0.9080(3) nm, c=1.3294(3) nm) was determined on single-crystal and powder specimens. The study was performed on a Philips PW1100 automatic diffractometer and a DRON-4.07 powder diffractometer. The Ce2Ni2Zn15 compound is crystallized in the Ce2Al2Co15 structure type with the aluminum positions being occupied by nickel and cobalt positions being occupied by zinc

On the Functionality of Complex Intermetallics: Frustration, Chemical Pressure Relief, and Potential Rattling Atoms in Y11Ni60C6.

Science.gov (United States)

Guo, Yiming; Fredrickson, Daniel C

2016-10-17

Intermetallic carbides provide excellent model systems for exploring how frustration can shape the structures and properties of inorganic materials. Combinations of several metals with carbon can be designed in which the formation of tetrahedrally close-packed (TCP) intermetallics conflicts with the C atoms' requirement of trigonal prismatic or octahedral coordination environments, as offered by the simple close-packings (SCP) of equally sized spheres. In this Article, we explore the driving forces that lead to the coexistence of these incompatible arrangements in the Yb 11 Ni 60 C 6 -type compound Y 11 Ni 60 C 6 (cI154), as well as potential consequences of this intergrowth for the phase's physical properties. Our focus begins on the structure's SCP regions, which appear as C-stuffed versions of a AuCu 3 -type YNi 3 phase that is not observed on its own in the Y-Ni system. DFT-Chemical Pressure (DFT-CP) calculations on this hypothetical YNi 3 phase reveal large negative pressures within the Ni sublattice, as it is stretched to accommodate the size requirements of the Y atoms. In the Y 11 Ni 60 C 6 structure, two structural mechanisms for addressing these CP issues appear: the incorporation of interstitial C atoms, and the presence of interfaces with CaCu 5 -type domains. The relative roles of these two mechanisms are investigated with the CP analysis on a hypothetical YNi 3 C x series of C-stuffed AuCu 3 -type phases, the Y-Ni sublattice of Y 11 Ni 60 C 6 , and finally the full Y 11 Ni 60 C 6 structure. Through these calculations, the C atoms appear to play the roles of relieving positive Y CPs and supporting relaxation at the AuCu 3 -type/CaCu 5 -type interfaces, where the cancellation occurs between opposite CPs experienced by the Y atoms in the two parent structures (following the epitaxial stabilization mechanism). The CP analysis of Y 11 Ni 60 C 6 also highlights a sublattice of Y and Ni atoms with large negative CPs (and thus the potential for soft

Magnetic ordering of Hf{sub 3}Ni{sub 2}Si{sub 3}-type {Sm, Tb, Er}{sub 3}Co{sub 2}Ge{sub 3} and {Tb, Ho}{sub 3}Ni{sub 2}Ge{sub 3} compounds

Energy Technology Data Exchange (ETDEWEB)

Morozkin, A.V., E-mail: morozkin@tech.chem.msu.ru [Department of Chemistry, Moscow State University, Leninskie Gory, House 1, Building 3, Moscow, GSP-1, 119991 (Russian Federation); Yapaskurt, V.O. [Department of Petrology, Geological Faculty Moscow State University, Leninskie Gory, Moscow 119991 (Russian Federation); Nirmala, R. [Indian Institute of Technology Madras, Chennai 600036 (India); Quezado, S.; Malik, S.K. [Departamento de Física Teórica e Experimental, Universidade Federal do Rio Grande do Norte, Natal 59082-970 (Brazil); Mozharivskyj, Y. [Department of Chemistry and Chemical Biology, McMaster University, 1280 Main Street West, Hamilton, Ontario, Canada L8S 4M1 (Canada); Isnard, O. [CNRS, Institut. Néel, 25 rue des Martyrs BP166 x, F-38042 Grenoble (France); Université Grenoble Alpes, Inst. Néel, F-38042 Grenoble (France)

2017-02-15

The magnetic ordering of Hf{sub 3}Ni{sub 2}Si{sub 3}-type {Sm, Tb, Er}{sub 3}Co{sub 2}Ge{sub 3} and {Tb, Ho}{sub 3}Ni{sub 2}Ge{sub 3} compounds (space group Cmcm, oC32) was investigated via magnetization measurements and neutron diffraction study in a zero-applied field. {Sm, Tb, Er}{sub 3}Co{sub 2}Ge{sub 3} and Ho{sub 3}Ni{sub 2}Ge{sub 3} exhibit field sensitive complex antiferromagnetic orderings with T{sub N}=51 K, T{sub m}=10 K for Sm{sub 3}Co{sub 2}Ge{sub 3}, T{sub N}=34 K, T{sub m}=13 K for Tb{sub 3}Co{sub 2}Ge{sub 3}, T{sub N}=7 K for Er{sub 3}Co{sub 2}Ge{sub 3} and T{sub N}=11 K for Ho{sub 3}Ni{sub 2}Ge{sub 3}. At 2 K and above the critical field of ~5 kOe, 20 kOe, 4 kOe and 7 kOe for Sm{sub 3}Co{sub 2}Ge{sub 3}, Tb{sub 3}Co{sub 2}Ge{sub 3}, Er{sub 3}Co{sub 2}Ge{sub 3} and Ho{sub 3}Ni{sub 2}Ge{sub 3}, respectively, saturation magnetizations per rare-earth atom are 6.5 μ{sub B} for Tb{sub 3}Co{sub 2}Ge{sub 3}, 7.0 μ{sub B} for Er{sub 3}Co{sub 2}Ge{sub 3} and 8.0 μ{sub B} for Ho{sub 3}Ni{sub 2}Ge{sub 3} in the field of 140 kOe, whereas magnetization of Sm{sub 3}Co{sub 2}Ge{sub 3} has an antiferromagnetic behaviour. The isothermal magnetic entropy change, ΔS{sub m}, indicates a field-induced ferromagnetic ordering in Sm{sub 3}Co{sub 2}Ge{sub 3}, Tb{sub 3}Co{sub 2}Ge3, Er{sub 3}Co{sub 2}Ge{sub 3} and Ho{sub 3}Ni{sub 2}Ge{sub 3} with a maximal ΔS{sub m} value of −10.9 J/kg K for Ho{sub 3}Ni{sub 2}Ge{sub 3} at 11 K for a field change of 50 kOe. In a zero-applied magnetic field, below T{sub N}=33 K and down to T{sub m}{sup ND}=15 K Tb{sub 3}Ni{sub 2}Ge{sub 3} shows an ac-antiferromagnetic ordering with the C2′/c magnetic space group, a K{sub 0}=[0, 0, 0] propagation vector and a a{sub Tb3Ni2Ge3}×b{sub Tb3Ni2Ge3}×c{sub Tb3Ni2Ge3} magnetic unit cell. Below T{sub m}{sup ND}=15 K, its magnetic structure is a sum of the ac-antiferromagnetic component with the C2′/c magnetic space group of the K{sub 0} vector and a sine-modulated a

Investigation of the Influence of Ni Doping on the Structure and Hardness of Ti-Ni-C Coatings

Directory of Open Access Journals (Sweden)

J. Daniel

2017-01-01

Full Text Available Nanocomposite nc-TiC/a-C:H thin films exhibit unique combination of mechanical properties, high hardness, low friction, and wear. Selective doping by weak-carbide forming element can be used in order to specifically design the physical and chemical properties of nc-TiC/a-C:H coatings. In this paper we report on an effect of nickel addition on structure and hardness of the nc-TiC/a-C:H coatings. The effect of Ni alloying on the coating structure under conditions of DCMS and HiPIMS depositions was studied. The coating structure was correlated with the coating hardness. The grain size, the grain carbon vacancy concentration, and the mean grain separation were found to be the key parameters determining the coating hardness. Ni doping proved to have a significant effect on the coating microstructure which resulted in changes of the hardness of the deposited coatings.

Experimental Investigations on Pulsed Nd:YAG Laser Welding of C17300 Copper-Beryllium and 49Ni-Fe Soft Magnetic Alloys

International Nuclear Information System (INIS)

Mousavi, S. A. A. Akbari; Ebrahimzadeh, H.

2011-01-01

Copper-beryllium and soft magnetic alloys must be joined in electrical and electro-mechanical applications. There is a high difference in melting temperatures of these alloys which cause to make the joining process very difficult. In addition, copper-beryllium alloys are of age hardenable alloys and precipitations can brittle the weld. 49Ni-Fe alloy is very hot crack sensitive. Moreover, these alloys have different heat transfer coefficients and reflection of laser beam in laser welding process. Therefore, the control of welding parameters on the formation of adequate weld puddle composition is very difficult. Laser welding is an advanced technique for joining of dissimilar materials since it can precisely control and adjust the welding parameters. In this study, a 100W Nd:YAG pulsed laser machine was used for joining 49Ni-Fe soft magnetic to C17300 copper-beryllium alloys. Welding of samples was carried out autogenously by changing the pulse duration, diameter of beam, welding speed, voltage and frequency. The spacing between samples was set to almost zero. The ample were butt welded. It was required to apply high voltage in this study due to high reflection coefficient of copper alloys. Metallography, SEM analysis, XRD and microhardness measurement was used for survey of results. The results show that the weld strength depends upon the chemical composition of the joints. To change the wells composition and heat input of the welds, it was attempted to deviate the laser focus away from the weld centerline. The best strength was achieved by deviation of the laser beam away about 0.1mm from the weld centerline. The result shows no intermetallic compounds if the laser beam is deviated away from the joint.

A FeNiMnC alloy with strain glass transition

Directory of Open Access Journals (Sweden)

Hui Ma

2018-02-01

Full Text Available Recent experimental and theoretical investigations suggested that doping sufficient point defects into a normal ferroelastic/martensitic alloy systems could lead to a frozen disordered state of local lattice strains (nanomartensite domains, thereby suppressing the long-range strain-ordering martensitic transition. In this study, we attempt to explore the possibility of developing novel ferrous Elinvar alloys by replacing nickel with carbon and manganese as dopant species. A nominal Fe89Ni5Mn4.6C1.4 alloy was prepared by argon arc melting, and XRD, DSC, DMA and TEM techniques were employed to characterize the strain glass transition signatures, such as invariance in average structure, frequency dispersion in dynamic mechanical properties (storage modulus and internal friction and the formation of nanosized strain domains. It is indicated that doping of Ni, Mn and C suppresses γ→α long-range strain-ordering martensitic transformation in Fe89Ni5Mn4.6C1.4 alloy, generating randomly distributed nanosized domains by strain glass transition. Keywords: Strain glass transition, Elinvar alloys, Point defects, Nanosized domains

Laser surface alloying of aluminum (AA1200) with Ni and SiC Powders

CSIR Research Space (South Africa)

Mabhali, Luyolo AB

2010-12-01

Full Text Available . The dissociated C reacted with Al to form Al4C3. The addition of Ni resulted in the formation of the Al3Ni phase. A hardness increase of approximately four times that of aluminum AA1200 was achieved in the alloyed layer....

Hot Corrosion Behavior of Bare, Cr3C2-(NiCr) and Cr3C2-(NiCr) + 0.2wt.%Zr Coated SuperNi 718 at 900 °C

Science.gov (United States)

Mudgal, Deepa; Singh, Surendra; Prakash, Satya

2015-01-01

Corrosion in incinerators, power plants, and chemical industries are frequently encountered due to the presence of salts containing sodium, sulphur, and chlorine. To obviate this problem, bare and coated alloys were tested under environments simulating the conditions present inside incinerators and power plants. 0.2 wt.% zirconium powder was incorporated in the Cr3C2-(NiCr) coating powder. The original powder and Zr containing powder was sprayed on Superni 718 alloy by D-gun technique. The bare and coated alloys were tested under Na2SO4 + K2SO4 + NaCl + KCl and Na2SO4 + NaCl environment. The corrosion rate of specimens was monitored using weight change measurements. Characterization of the corrosion products has been done using FE-SEM/EDS and XRD techniques. Bare and coated alloys showed very good corrosion resistance under given molten salt environments. Addition of 0.2wt.%Zr in Cr3C2-25%(NiCr) coating further greatly reduced the oxidation rate as well as improved the adherence of oxide scale to the coating surface during the time of corrosion.

Cs2SO4-Pr2(SO4)3-H2O and NiSO4-Pr2(SO4)3-H2O systems at 75 deg C

International Nuclear Information System (INIS)

Onishchenko, M.K.; Skorikov, V.M.; Shevchuk, V.G.; AN SSSR, Moscow. Inst. Obshchej i Neorganicheskoj Khimii)

1979-01-01

To investigate physico-chemical properties of equilibrium saturated solutions and to elucidate the chemical changes under way, the aqueous systems of cesium, nickel and praseodymium (3) sulfates are studied. The method of isothermal saturation of salts at 75 deg C is used. It has been found that in the system Cs 2 SO 4 -Pr 2 (SO 4 ) 3 -H 2 O in a wide concentration range the soluble binary salt Cs 2 SO 4 xPr 2 (SO 4 ) 3 csytallizes in a congruent way. For the system NiSO 4 -Pr 2 (SO 4 ) 3 -H 2 O a solubility curve of the eutonic type is obtained, there being no chemical interaction between the components. The solubility isotherms for the system are given

The Ce-Ni-Si system as a representative of the rare earth-Ni-Si family: Isothermal section and new rare-earth nickel silicides

Energy Technology Data Exchange (ETDEWEB)

Morozkin, A.V., E-mail: morozkin@tech.chem.msu.ru [Department of Chemistry, Moscow State University, Leninskie Gory, House 1, Building 3, Moscow, GSP-1, 119991 (Russian Federation); Knotko, A.V.; Garshev, A.V. [Department of Chemistry, Moscow State University, Leninskie Gory, House 1, Building 3, Moscow, GSP-1, 119991 (Russian Federation); Faculty of Materials Science, Moscow State University, Leninskie Gory, House 1, Building 73, Moscow, GSP-1, 119991 (Russian Federation); Yapaskurt, V.O. [Department of Petrology, Geological Faculty Moscow State University, Leninskie Gory, Moscow 119991 (Russian Federation); Nirmala, R. [Indian Institute of Technology Madras, Chennai 600036 (India); Quezado, S.; Malik, S.K. [Departamento de Física Teórica e Experimental, Universidade Federal do Rio Grande do Norte, Natal, 59082-970 (Brazil)

2016-11-15

The Ce-Ni-Si system has been investigated at 870/1070 K by X-ray and microprobe analyses. The existence of the known compounds, i.e.: Ce{sub 2}Ni{sub 15.8}Si{sub 1.2} (Th{sub 2}Ni{sub 17}-type), Ce{sub 2}Ni{sub 15-14}Si{sub 2-3} (Th{sub 2}Zn{sub 17}-type), CeNi{sub 8.6}Si{sub 2.4} (BaCd{sub 11}-type), CeNi{sub 8.8}Si{sub 4.2} (LaCo{sub 9}Si{sub 4}-type), CeNi{sub 6}Si{sub 6} (CeNi{sub 6}Si{sub 6}-type), CeNi{sub 5}Si{sub 1-0.3} (TbCu{sub 7}-type), CeNi{sub 4}Si (YNi{sub 4}Si-type), CeNi{sub 2}Si{sub 2} (CeGa{sub 2}Al{sub 2}-type), Ce{sub 2}Ni{sub 3}Si{sub 5} (U{sub 2}Co{sub 3}Si{sub 5}-type), Ce{sub 3}Ni{sub 6}Si{sub 2} (Ce{sub 3}Ni{sub 6}Si{sub 2}-type), Ce{sub 3}Ni{sub 4}Si{sub 4} (U{sub 3}Ni{sub 4}Si{sub 4}-type), CeNiSi{sub 2} (CeNiSi{sub 2}-type), ~CeNi{sub 1.3}Si{sub 0.7} (unknown type structure), Ce{sub 6}Ni{sub 7}Si{sub 4} (Pr{sub 6}Ni{sub 7}Si{sub 4}-type), CeNiSi (LaPtSi-type), CeNi{sub 0.8-0.3}Si{sub 1.2-1.7} (AlB{sub 2}-type), ~Ce{sub 2}Ni{sub 2}Si (unknown type structure), ~Ce{sub 4.5}Ni{sub 3.5}Si{sub 2} (unknown type structure), Ce{sub 15}Ni{sub 7}Si{sub 10} (Pr{sub 15}Ni{sub 7}Si{sub 10}-type), Ce{sub 5}Ni{sub 1.85}Si{sub 3} (Ce{sub 5}Ni{sub 1.85}Si{sub 3}-type), Ce{sub 6}Ni{sub 1.4}Si{sub 3.4} (Ce{sub 6}Ni{sub 1.67}Si{sub 3}-type), Ce{sub 7}Ni{sub 2}Si{sub 5} (Ce{sub 7}Ni{sub 2}Si{sub 5}-type) and Ce{sub 3}NiSi{sub 3} (Y{sub 3}NiSi{sub 3}-type) has been confirmed in this section. Moreover, the type structure has been determined for ~Ce{sub 2}Ni{sub 2}Si (Mo{sub 2}NiB{sub 2}-type Ce{sub 2}Ni{sub 2.5}Si{sub 0.5}) and ~Ce{sub 4.5}Ni{sub 3.5}Si{sub 2} (W{sub 3}CoB{sub 3}-type Ce{sub 3}Ni{sub 3-2.7}Si{sub 1-1.3}) and new ternary phases Ce{sub 2}Ni{sub 6.25}Si{sub 0.75} (Gd{sub 2}Co{sub 7}-type), CeNi{sub 7-7.6}Si{sub 6-5.4} (GdNi{sub 7}Si{sub 6}-type) and ~Ce{sub 27}Ni{sub 42}Si{sub 31} (unknown type structure) have been identified in this system. Quasi-binary phases, solid solutions, were detected at 870/1070 K for CeNi{sub 5}, CeNi{sub 3} and Ce

α-NiPt(Al) and phase equilibria in the Ni-Al-Pt system at 1150 deg C

International Nuclear Information System (INIS)

Hayashi, S.; Ford, S.I.; Young, D.J.; Sordelet, D.J.; Besser, M.F.; Gleeson, B.

2005-01-01

The α-NiPt(Al) phase and its associated equilibria in the Ni-Al-Pt system at 1150 deg C were investigated by analyzing equilibrated bulk alloys and the interdiffusion zones of diffusion couples. Phase constitutions, tie-lines and microstructures were determined using a combination of techniques, including high-energy synchrotron X-ray diffraction, scanning electron microscopy and electron probe microanalysis. A large Pt solubility limit was found to exist in the β-NiAl, ∼42 at.%, and in γ'-Ni 3 Al, ∼32 at.%. The α-NiPt(Al) phase was found to have wide Pt solubility range of about 33-60 at.% and to skew along an almost constant Pt/Al ratio of 1.5. The α-NiPt(Al) has an ordered face-centered tetragonal L1 0 crystal structure, with the Al and Pt atoms found to be preferentially located in the corners and prismatic faces, respectively. The temperature dependence of the lattice parameters and unit cell volume of the α phase were also determined

Structural chemistry and magnetic properties of Pr3-xSr1+xCrNiO8

International Nuclear Information System (INIS)

Dutton, Sian E.; Bahout, Mona; Battle, Peter D.; Tonus, Florent; Demange, Valerie

2008-01-01

Polycrystalline samples of the n=1 Ruddlesden-Popper system Pr 3-x Sr 1+x CrNiO 8 have been synthesized over the composition range 0.0 0.1 adopt the tetragonal space group I4/mmm; Pr 2.9 Sr 1.1 CrNiO 8 adopts the orthorhombic space group Fmmm. There is no evidence of Cr/Ni cation ordering in any composition. A maximum in the zero-field cooled magnetic susceptibility is observed at a temperature T f that decreases with increasing Sr content; 52≤T f (K)≤13. The frequency dependence of T f observed in a.c. susceptibility measurements, together with the analysis of neutron diffraction data, suggests that the atomic magnetic moments in these compositions adopt a spin-glass-like state below T f . - Graphical abstract: The n=1 Ruddlesden-Popper system Pr 3-x Sr 1+x CrNiO 8 (0.0< x≤1.0) has been characterized by diffraction methods and magnetometry. There is no evidence of Cr/Ni cation ordering in any composition. The atomic magnetic moments adopt a spin-glass-like state below a transition temperature that decreases from 52 K (x=0.1) to 13 K (x=1.0)

Direct methanol fuel cells: Pt-Ni/C binary electrocatalysts; Celulas a combutivel de metanol direto: eletrocatalisadores binarios de Pt-Ni/C

Energy Technology Data Exchange (ETDEWEB)

Salgado, Jose Ricardo Cezar; Antolini, Ermete; Santos, Ana Maria dos; Gonzalez, Ernesto Rafael [Universidade de Sao Paulo (USP), Sao Carlos, SP (Brazil). Inst. de Quimica], e-mail: salgado@iqsc.usp.br

2004-07-01

Direct methanol fuel cells use platinum alloys as more efficient catalysts than platinum. In the case of binary alloys, the second metal affects several properties of platinum, like the interatomic distance, the electronic density and the capacity of forming oxygenated species at lower potentials. In this work, Pt-Ni catalysts supported on high surface area carbon (Pt-Ni/C) were prepared and characterized, and tested as catalysts in the anode and the cathode in direct methanol fuel cells. In both cases the performance of the material was better than that of Pt/C, and comparing the two situations it was better when the material was used in the cathode. The improved performance in the cathode was attributed to the nickel that forms a true alloy with platinum, while the better performance in the anode was attributed to the presence of nickel oxides. (author)

Studies on SiC(p) reinforced Al-Al sub 3 Ni eutectic matrix composites

International Nuclear Information System (INIS)

Masrom, A.K.; Foo, L.C.; Ismail, A.B.

1996-01-01

An investigation on processing of Al-5.69wt% Ni eutectic with SiC particulate composites is reported. The intermetallic composites are prepared by elemental powder metallurgy route and sintered at two different temperatures, i.e., 600 degree C and 620 degree C. Results show that the metal matrix was Al-Al sub 3 Ni eutectic. The phase analysis by XRD identified the presence of Al sub 3 Ni and Al as dominant phases together with silicon and Al sub 4 C sub 3 phase as minor phases. The Al sub 4 C sub 3 and Si phases are formed during sintering due to SiC-Al interface reaction. SEM micrographs also reveal the formation of microvoid surrounding the SiC particle

Synthesis Of NiCrAlC alloys by mechanical alloying

International Nuclear Information System (INIS)

Silva, A.K.; Pereira, J.I.; Vurobi Junior, S.; Cintho, O.M.

2010-01-01

The purpose of the present paper is the synthesis of nickel alloys (NiCrAlC), which has been proposed like a economic alternative to the Stellite family Co alloys using mechanical alloying, followed by sintering heat treatment of milled material. The NiCrAlC alloys consist of a chromium carbides dispersion in a Ni 3 Al intermetallic matrix, that is easily synthesized by mechanical alloying. The use of mechanical alloying enables higher carbides sizes and distribution control in the matrix during sintering. We are also investigated the compaction of the processed materials by compressibility curves. The milling products were characterized by X-ray diffraction, and the end product was featured by conventional metallography and scanning electronic microscopy (SEM), that enabled the identification of desired phases, beyond microhardness test, which has been shown comparable to alloys manufactured by fusion after heat treating. (author)

Thermal stability of Ni-Pt-Ta alloy silicides on epi-Si{sub 1-x}C{sub x}

Energy Technology Data Exchange (ETDEWEB)

Yoo, Jung-Ho; Chang, Hyun-Jin [Department of Ceramic Engineering, Yonsei University, Seoul 120-749 (Korea, Republic of); Min, Byoung-Gi [Department of Ceramic Engineering, Yonsei University, Seoul 120-749 (Korea, Republic of); Jusung Engineering Co., Ltd., 49, Neungpyeong-ri, Opo-eup, Gwangju-Si, Kyunggi-do 464-892 (Korea, Republic of); Ko, Dae-Hong [Department of Ceramic Engineering, Yonsei University, Seoul 120-749 (Korea, Republic of)], E-mail: dhko@yonsei.ac.kr; Cho, Mann-Ho [Institute of Physics and Applied Physics, Yonsei University, Seoul 120-749 (Korea, Republic of); Sohn, Hyunchul [Department of Ceramic Engineering, Yonsei University, Seoul 120-749 (Korea, Republic of); Lee, Tae-Wan [Jusung Engineering Co., Ltd., 49, Neungpyeong-ri, Opo-eup, Gwangju-Si, Kyunggi-do 464-892 (Korea, Republic of)

2008-12-05

We investigated the silicide formation in Ni/epi-Si{sub 1-x}C{sub x} systems. Ni-Pt and Ni-Pt-Ta films were deposited on epi-Si{sub 1-x}C{sub x}/Si substrates by DC magnetron sputtering and processed at various temperatures. The sheet resistance of the silicide from the Ni alloy/epi-Si{sub 1-x}C{sub x} systems was maintained at low values compared to that from Ni/Si systems. By TEM and EDS analyses, we confirmed the presence of a Pt alloy layer at the top of the Ni-silicide layer. The stability of the silicide layer in the Ni alloy/epi-Si{sub 1-x}C{sub x} system is explained by not only the Pt rich layer on the top of the Ni-silicide layer, but also by the presence of a small amount of Pt in the Ni-silicide layer or at the grain boundaries. And both the thermal stability and the morphology of silicide were greatly improved by the addition of Ta in Ni-Pt films.

Characterization of Al/Ni multilayers and their application in diffusion bonding of TiAl to TiC cermet

International Nuclear Information System (INIS)

Cao, J.; Song, X.G.; Wu, L.Z.; Qi, J.L.; Feng, J.C.

2012-01-01

The Al/Ni multilayers were characterized and diffusion bonding of TiAl intermetallics to TiC cermets was carried out using the multilayers. The microstructure of Al/Ni multilayers and TiAl/TiC cermet joint was investigated. The layered structures consisting of a Ni 3 (AlTi) layer, a Ni 2 AlTi layer, a (Ni,Al,Ti) layer and a Ni diffusion layer were observed from the interlayer to the TiAl substrate. Only one AlNi 3 layer formed at the multilayer/TiC cermet interface. The reaction behaviour of Al/Ni multilayers was characterized by means of differential scanning calorimeter (DSC) and X-ray diffraction. The initial exothermic peak of the DSC curve was formed due to the formation of Al 3 Ni and Al 3 Ni 2 phases. The reaction sequence of the Al/Ni multilayers was Al 3 Ni → Al 3 Ni 2 → AlNi → AlNi 3 and the final products were AlNi and AlNi 3 phases. The shear strength of the joint was tested and the experimental results suggested that the application of Al/Ni multilayers improved the joining quality. - Highlights: ► Diffusion bonding of TiAl to TiC cermet was realized using Al/Ni multilayer. ► The reaction sequence of the Al/Ni multilayers was Al 3 Ni → Al 3 Ni 2 → AlNi → AlNi 3 . ► The interfacial microstructure of the joint was clarified. ► The application of Al/Ni multilayers improved the joining quality.

All-electron ab initio investigations of the electronic states of the NiC molecule

DEFF Research Database (Denmark)

Shim, Irene; Gingerich, Karl. A.

1999-01-01

The low-lying electronic states of NiC are investigated by all-electron ab initio multi-configuration self-consistent-field (CASSCF) calculations including relativistic corrections. The electronic structure of NiC is interpreted as perturbed antiferromagnetic couplings of the localized angular...

Magnetic ordering of YPd{sub 2}Si-type HoNi{sub 2}Si and ErNi{sub 2}Si compounds

Energy Technology Data Exchange (ETDEWEB)

Morozkin, A.V., E-mail: morozkin@tech.chem.msu.ru [Department of Chemistry, Moscow State University, Leninskie Gory, House 1, Building 3, GSP-2, Moscow, 119992 (Russian Federation); Isnard, O. [CNRS, Insitut. Néel, 25 Rue Des Martyrs BP166 x, F-38042 Grenoble (France); Université Grenoble Alpes, Inst. Néel, F-38042 Grenoble (France); Nirmala, R. [Indian Institute of Technology Madras, Chennai 600 036 (India); Quezado, S.; Malik, S.K. [Departamento de Física Teórica e Experimental, Universidade Federal do Rio Grande do Norte, Natal 59082-970 (Brazil)

2016-12-01

Magnetic properties of YPd{sub 2}Si-type HoNi{sub 2}Si and ErNi{sub 2}Si were investigated via neutron diffraction and magnetisation measurements. HoNi{sub 2}Si and ErNi{sub 2}Si show ferromagnetic-like ordering at T{sub C} of 9 K and 7 K, respectively. The paramagnetic Weiss temperatures are 9 K and 11 K and the effective magnetic moments are 10.76 μ{sub B}/fu and 9.79 μ{sub B}/fu for HoNi{sub 2}Si and ErNi{sub 2}Si compounds, respectively. The HoNi{sub 2}Si and ErNi{sub 2}Si are soft ferromagnets with saturation magnetization of 8.1 μ{sub B}/fu and 7.5 μ{sub B}/fu, respectively at 2 K and in field of 140 kOe. The isothermal magnetic entropy change, ΔS{sub m}, has a maximum value of −15.6 J/kg·K at 10 K for HoNi{sub 2}Si and −13.9 J/kg·K at 6 K for ErNi{sub 2}Si for a field change of 50 kOe. Neutron diffraction study in zero applied field shows mixed ferromagnetic-antiferromagnetic ordering of HoNi{sub 2}Si at ~9 K and its magnetic structure is a sum of a-axis ferromagnetic F{sub a}, b-axis antiferromagnetic AF{sub b} and c-axis antiferrromagnetic AF{sub c} components of Pn′a2{sub 1}′={1, m_x′/[1/2, 1/2, 1/2], 2_y′/[0, 1/2, 0], m_z/[1/2, 0, 1/2]} magnetic space group and propagation vector K{sub 0}=[0, 0, 0]. The holmium magnetic moment reaches a value of 9.23(9) μ{sub B} at 1.5 K and the unit cell of HoNi{sub 2}Si undergoes isotropic contraction around the temperature of magnetic transition. - Graphical abstract: HoNi{sub 2}Si: mixed ferro-antiferromagnet (F{sub a}+AF{sub b}+AF{sub c}){sup K0} with Pn′a2{sub 1}′ magnetic space group and K{sub 0}=[0, 0, 0] propagation vector below 10 K. - Highlights: • Ferro-antiferromagnetic ordering is observed in HoNi{sub 2}Si at 9 K and in ErNi{sub 2}Si at 7 K. • HoNi{sub 2}Si is soft ferromagnet with ΔS{sub m} of −15.6 J/kg·K at 10 K in field of 0–50 kOe. • ErNi{sub 2}Si is soft ferromagnet with ΔS{sub m} of −13.9 J/kg·K at 6 K in field of 0–50 kOe. • HoNi{sub 2}Si shows mixed F�

Studies on Ta-Ni alloys as high-temperature braze for SiC-SiC joined products; Untersuchungen zu Ta-Ni-Legierungen als Hochtemperaturlot fuer SiC-SiC Verbunde

Energy Technology Data Exchange (ETDEWEB)

Triebert, Anke; Matthey, Bjoern; Martin, Hans-Peter [Fraunhofer Institut fuer Keramische Technologien und Systeme (IKTS), Dresden (Germany)

2011-07-01

Active metal brazes have been already established for a number of decades. The current progress of processing technologies and engineering require new and powerful materials also for high-temperature applications. Up to now there are little technically and industrially applicable brazing materials for operation temperatures above 800 C. The investigations described in this paper concerning the Ta-Ni system intend to be the start of a braze material development, which delivers ceramic-ceramic or ceramic-metal joined products. Besides principal considerations and experiments with regard to the investigated material system of Ta-Ni active metal brazing tests to join SIC-SIC components are presented. The joined ceramic component samples are characterized focusing on their materials structure within the joining zone, their crystalline phases of the braze and their mechanical strength at room temperature and high temperatures. The achieved properties demonstrate that Ta-Ni brazes have the potential for future high temperature brazes for ceramics materials. (orig.)

Mechanical properties and wear and corrosion resistance of electrodeposited Ni-Co/SiC nanocomposite coating

International Nuclear Information System (INIS)

Shi Lei; Sun Chufeng; Gao Ping; Zhou Feng; Liu Weimin

2006-01-01

Ni-Co/SiC nanocomposite coatings with various contents of SiC nano-particulates were prepared by electrodeposition in a Ni-Co plating bath containing SiC nano-particulates to be co-deposited. The influences of the nanoparticulates concentration, current density, stirring rate and temperature of the plating bath on the composition of the coatings were investigated. The shape and size of the SiC nano-particulates were observed and determined using a transmission electron microscope. The polarization behavior of the composite plating bath was examined on a PAR-273A potentiostat/galvanostat device. The wear behavior of the Ni-Co/SiC nanocomposite coatings was evaluated on a ball-on-disk UMT-2MT test rig. The worn surface morphologies of the Ni-Co/SiC nanocomposite coatings were observed using a scanning electron microscope. The corrosion behavior of the nanocomposite coatings was evaluated by charting the Tafel curves of the solution of 0.5 mol L -1 NaCl at room temperature. It was found that the cathodic polarization potential of the composite electrolyte increased with increasing SiC concentration in the plating bath. The microhardness and wear and corrosion resistance of the nanocomposite coatings also increased with increasing content of the nano-SiC in the plating bath, and the morphologies of the nanocomposite coatings varied with varying SiC concentration in the plating bath as well. Moreover, the co-deposited SiC nano-particulates were uniformly distributed in the Ni-Co matrix and contributed to greatly increase the microhardness and wear resistance of the Ni-Co alloy coating

Laser cladding Ni-base composite coating on titanium alloy with pre-placed B4C+NiCoCrAlY

International Nuclear Information System (INIS)

Qingwu Meng; Lin Geng; Zhenzhu Zheng

2005-01-01

Using a CO 2 laser, a process of cladding Ni-base composite coating on Ti6Al4V with pre-placed B 4 C and NiCoCrAlY was studied. A good metallurgical bonding coating without cracks and pores was obtained in reasonable ratio of components and low energy laser process. Morphology and microstructure of the coating were analyzed with OM, XRD, SEM and EDS. It is certain that there was a reaction between B 4 C and Ti during in-situ producing TiB 2 and TiC. The Ni-base composite coating is strengthened with TiB 2 and TiC reinforcement phases. Vickers hardness tester measured that the average microhardness of the coating is HV1200 and it is 3.5 times of the Ti6Al4V substrate. The high hard coating containing several reinforcement phases greatly enhances wear resistance of titanium alloy. (orig.)

Stress-induced martensitic transformations in NiTi and NiTi-TiC composites investigated by neutron diffraction

International Nuclear Information System (INIS)

Vaidyanathan, R.; Dunand, D.C.

1999-01-01

Superelastic NiTi (51.0 at.% Ni) specimens reinforced with 0, 10 and 20 vol.% TiC particles were deformed under uniaxial compression while neutron diffraction spectra were collected. The experiments yielded in-situ measurements of the thermoelastic stress-induced transformation. The evolution of austenite/martensite phase fractions and of elastic strains in the reinforcing TiC particles and the austenite matrix were obtained by Rietveld refinement during the loading cycle as the austenite transforms to martensite (and its subsequent back transformation during unloading). Phase fractions and strains are discussed in terms of load transfer in composites where the matrix undergoes a stress-induced phase transformation. (orig.)

Preparation and corrosion resistance of electroless Ni-P/SiC functionally gradient coatings on AZ91D magnesium alloy

Science.gov (United States)

Wang, Hui-Long; Liu, Ling-Yun; Dou, Yong; Zhang, Wen-Zhu; Jiang, Wen-Feng

2013-12-01

In this paper, the protective electroless Ni-P/SiC gradient coatings on AZ91D magnesium alloy substrate were successfully prepared. The prepared Ni-P/SiC gradient coatings were characterized for its microstructure, morphology, microhardness and adhesion to the substrate. The deposition reaction kinetics was investigated and an empirical rate equation for electroless Ni-P/SiC plating on AZ91D magnesium alloy was developed. The anticorrosion properties of the Ni-P/SiC gradient coatings in 3.5 wt.% NaCl solution were evaluated by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) studies. The potentiodynamic polarization measurements revealed that the SiC concentration in the bath and heat treatment can influence the corrosion protection performance of electroless deposited Ni-P/SiC gradient coatings. EIS studies indicated that higher charge transfer resistance and slightly lower capacitance values were obtained for Ni-P/SiC gradient coatings compared to Ni-P coatings. The corrosion resistance of the Ni-P/SiC gradient coatings increases initially and decreases afterwards with the sustained increasing of immersion time in the aggressive medium. The electroless Ni-P/SiC gradient coatings can afford better corrosion protection for magnesium alloy substrate compared with Ni-P coatings.

3d-metal doping (Fe,Co,Ni,Zn) of the high T/sub c/ perovskite YBa/sub 2/Cu/sub 3/O/sub 7-y/

International Nuclear Information System (INIS)

Tarascon, J.M.; Barboux, P.; Greene, L.H.; Hull, G.W.; Bagley, B.G.

1988-01-01

The structural, magnetic and superconducting properties of the mixed compounds YBa/sub 2/Cu/sub 3-x/M/sub x/O/sub 7-y/ (M = Ni, Zn, Fe and Co) are reported. Values of y, determined by titration, are found to be dependent on the nature and amount of the doping. The range of solubility is greater for the Fe and Co compounds (chi = 1) than for those with Ni or Zn (chi = 0.3). The undoped material is orthorhombic and remains orthorhombic after substitution for Cu by Ni or Zn, whereas a tetragonal phase is observed when Fe, Co are substituted for Cu. DC resistance and AC susceptibility measurements show that T/sub c/ is depressed from 90K (chi = 0) to 45K (chi = 0.2) for both the Ni and Zn doped compounds and T/sub c/ is destroyed in the Fe and Co doped compounds when chi reaches 0.4. The authors suggest that a valance of 2 be assigned to the Ni and Zn and 3 to the Fe and Co ions

Interfacial study of NiTi–Ti{sub 3}SiC{sub 2} solid state diffusion bonded joints

Energy Technology Data Exchange (ETDEWEB)

Kothalkar, A. [Department of Materials Science and Engineering, Texas A and M University, College Station, TX 77843 (United States); Cerit, A. [Department of Industrial Design Engineering, Erciyes University, Kayseri (Turkey); Proust, G. [School of Civil Engineering, University of Sydney, Sydney, NSW 2006 (Australia); Basu, S. [Agilent Technologies, Chandler, AZ (United States); Radovic, M., E-mail: mradovic@tamu.edu [Department of Materials Science and Engineering, Texas A and M University, College Station, TX 77843 (United States); Karaman, I., E-mail: ikaraman@tamu.edu [Department of Materials Science and Engineering, Texas A and M University, College Station, TX 77843 (United States)

2015-01-12

The interfaces between the stress-assisted diffusion bonded Ti{sub 3}SiC{sub 2} and equiatomic NiTi, two distinct material systems that show pseudoelasticity were studied. The interfaces were formed in the 800–1000 °C temperature range, for 1, 5 and 10 h under flowing argon. Bonding was observed in all the cases considered, except at 800 °C after 1 h. Morphology and reaction phases in the interface were characterized using scanning electron microscopy, elemental micro probe analysis and electron backscatter diffraction analysis. The interfacial structure formed between NiTi and Ti{sub 3}SiC{sub 2} layers consists of NiTi/Ti{sub 2}Ni/Ti{sub 5}Si{sub 3}/NiTiSi/Ti{sub 3}SiC{sub 2}. Diffusion of Si into NiTi from Ti{sub 3}SiC{sub 2}, and Ni from NiTi into reaction zone was found to be responsible for the formation of reaction layers in the interface and thus for bonding at these conditions. The overall reaction layer thickness grows following the parabolic kinetic law. Nano-indentation and Vickers micro hardness tests were carried out to investigate the mechanical properties of the interface. Nano-indentation showed that the elastic moduli of the phases in the interface are close to that of Ti{sub 3}SiC{sub 2} while their hardness is higher than that of both Ti{sub 3}SiC{sub 2} and NiTi. Artificially formed cracks through microindents were observed to be branched and propagated into Ti{sub 3}SiC{sub 2} phase indicating good resistance against delamination.

Stability of an amorphous alloy of the Mm-Al-Ni-Cu system

Directory of Open Access Journals (Sweden)

Carlos Triveño Rios

2012-10-01

Full Text Available An investigation was made of the stability of melt-spun ribbons of Mm55Al25Ni10Cu10 (Mm = Mischmetal amorphous alloy. The structural transformations that occurred during heating were studied using a combination of X-ray diffraction (XRD and differential scanning calorimetry (DSC. Crystallization took place through a multi-stage process. The first stage of transformation corresponded to the formation of a metastable phase followed by cfc-Al precipitation, while in the second stage, exothermic transformations led to the formation of complex and unidentified Mm(Cu, Ni and MmAl(Cu, Ni phases. The transformation curves recorded from isothermal treatments at 226 °C and 232 °C indicated that crystallization occurred through nucleation and growth, with diffusion-controlled growth occurring in the first crystallization stage. The supercooled liquid region, ∆Tx, at 40 K/min was ~80 K. This value was obtained by the substitution of Mm (=Ce + La + Nd + Pr for La or Ce, saving chemical element-related costs.

Research on microstructure properties of the TiC/Ni-Fe-Al coating prepared by laser cladding technology

Science.gov (United States)

Jiao, Junke; Xu, Zifa; Zan, Shaoping; Zhang, Wenwu; Sheng, Liyuan

2017-10-01

In this paper, the laser cladding method was used to preparation the TiC reinforced Ni-Fe-Al coating on the Ni base superalloy. The Ti/Ni-Fe-Al powder was preset on the Ni base superalloy and the powder layer thickness is 0.5mm. A fiber laser was used the melting Ti/Ni-Fe-Al powder in an inert gas environment. The shape of the cladding layer was tested using laser scanning confocal microscope (LSCM) under different cladding parameters such as the laser power, the melting velocity and the defocused amount. The microstructure, the micro-hardness was tested by LSCM, SEM, Vickers hardness tester. The test result showed that the TiC particles was distributed uniformly in the cladding layer and hardness of the cladding layer was improved from 180HV to 320HV compared with the Ni-Fe-Al cladding layer without TiC powder reinforced, and a metallurgical bonding was produced between the cladding layer and the base metal. The TiC powder could make the Ni-Fe-Al cladding layer grain refining, and the more TiC powder added in the Ni-Fe-Al powder, the smaller grain size was in the cladding layer.

Single-crystal study of the charge density wave metal LuNiC2

Science.gov (United States)

Steiner, S.; Michor, H.; Sologub, O.; Hinterleitner, B.; Höfenstock, F.; Waas, M.; Bauer, E.; Stöger, B.; Babizhetskyy, V.; Levytskyy, V.; Kotur, B.

2018-05-01

We report on single-crystal growth, single-crystal x-ray diffraction, physical properties, and density functional theory (DFT) electronic structure as well as Fermi surface calculations for two ternary carbides, LuCoC2 and LuNiC2. Electrical resistivity measurements reveal for LuNiC2 a charge density wave (CDW) transition at TCDW≃450 K and, for T >TCDW , a significant anisotropy of the electrical resistivity, which is lowest along the orthorhombic a axis. The analysis of x-ray superstructure reflections suggest a commensurate CDW state with a Peierls-type distortion of the Ni atom periodicity along the orthorhombic a axis. DFT calculations based on the CDW modulated monoclinic structure model of LuNiC2 as compared to results of the orthorhombic parent type reveal the formation of a partial CDW gap at the Fermi level which reduces the electronic density of states from N (EF)=1.03 states/eV f.u. without CDW to N (EF)=0.46 states/eV f.u. in the CDW state. The corresponding bare DFT Sommerfeld value of the latter, γDFTCDW=0.90 mJ/mol K2, reaches reasonable agreement with the experimental value γ =0.83 (5 ) mJ/mol K2 of LuNiC2. LuCoC2 displays a simple metallic behavior with neither CDW ordering nor superconductivity above 0.4 K. Its experimental Sommerfeld coefficient, γ =5.9 (1) mJ/mol K2, is in realistic correspondence with the calculated, bare Sommerfeld coefficient, γDFT=3.82 mJ/mol K2, of orthorhombic LuCoC2.

Nanocatalytic growth of Si nanowires from Ni silicate coated SiC nanoparticles on Si solar cell.

Science.gov (United States)

Parida, Bhaskar; Choi, Jaeho; Ji, Hyung Yong; Park, Seungil; Lim, Gyoungho; Kim, Keunjoo

2013-09-01

We investigated the nanocatalytic growth of Si nanowires on the microtextured surface of crystalline Si solar cell. 3C-SiC nanoparticles have been used as the base for formation of Ni silicate layer in a catalytic reaction with the Si melt under H2 atmosphere at an annealing temperature of 1100 degrees C. The 10-nm thick Ni film was deposited after the SiC nanoparticles were coated on the microtextured surface of the Si solar cell by electron-beam evaporation. SiC nanoparticles form a eutectic alloy surface of Ni silicate and provide the base for Si supersaturation as well as the Ni-Si alloy layer on Si substrate surface. This bottom reaction mode for the solid-liquid-solid growth mechanism using a SiC nanoparticle base provides more stable growth of nanowires than the top reaction mode growth mechanism in the absence of SiC nanoparticles. Thermally excited Ni nanoparticle forms the eutectic alloy and provides collectively excited electrons at the alloy surface, which reduces the activation energy of the nanocatalytic reaction for formation of nanowires.

Análisis mecánico y tribológico de los recubrimientos fe-cr-ni-c y ni-al-mo

Directory of Open Access Journals (Sweden)

JORGE E. MUÑOZ

2007-01-01

Full Text Available En este trabajo de investigación se evaluaron dos recubrimientos aplicados por medio de la técnica de rociado térmico por combustión, la aleación: Ni=89%, Al = 5,5%, Mo=5,5% y la aleación Fe=81,8%, Cr=16%, Ni=2%, C=0,2. La preparación superficial de las probetas se realizó usando chorro de arena. Se realizaron pruebas de resistencia al cortante, adherencia, desgaste abrasivo, desgaste por deslizamiento y flexión en cuatro puntos. El recubrimiento Fe-Cr-Ni-C presentó menor pérdida de masa, tanto para desgaste abrasivo como para el desgaste por deslizamiento. La multicapa presentó una mayor porosidad en el recubrimiento Ni-Al- Mo usado como capa base y la capa exterior de Fe-Cr-Ni-C presentó mayor cantidad de partículas no fundidas y óxidos. La falla ocurrida en el ensayo de adherencia para las probetas con recubrimiento multicapa fue de característica adhesiva y cohesiva. El esfuerzo en el que se presenta la fisura por flexión en el recubrimiento multicapa disminuyó con el aumento del espesor

Characterization of Al/Ni multilayers and their application in diffusion bonding of TiAl to TiC cermet

Energy Technology Data Exchange (ETDEWEB)

Cao, J., E-mail: cao_jian@hit.edu.cn [State Key Lab of Advanced Welding Production Technology, Harbin Institute of Technology, Harbin, 150001 (China); Center for Composite Materials and Structures, Harbin Institute of Technology, Harbin, 150001 (China); Song, X.G. [State Key Lab of Advanced Welding Production Technology, Harbin Institute of Technology, Harbin, 150001 (China); Wu, L.Z. [Center for Composite Materials and Structures, Harbin Institute of Technology, Harbin, 150001 (China); Qi, J.L.; Feng, J.C. [State Key Lab of Advanced Welding Production Technology, Harbin Institute of Technology, Harbin, 150001 (China)

2012-02-29

The Al/Ni multilayers were characterized and diffusion bonding of TiAl intermetallics to TiC cermets was carried out using the multilayers. The microstructure of Al/Ni multilayers and TiAl/TiC cermet joint was investigated. The layered structures consisting of a Ni{sub 3}(AlTi) layer, a Ni{sub 2}AlTi layer, a (Ni,Al,Ti) layer and a Ni diffusion layer were observed from the interlayer to the TiAl substrate. Only one AlNi{sub 3} layer formed at the multilayer/TiC cermet interface. The reaction behaviour of Al/Ni multilayers was characterized by means of differential scanning calorimeter (DSC) and X-ray diffraction. The initial exothermic peak of the DSC curve was formed due to the formation of Al{sub 3}Ni and Al{sub 3}Ni{sub 2} phases. The reaction sequence of the Al/Ni multilayers was Al{sub 3}Ni {yields} Al{sub 3}Ni{sub 2} {yields} AlNi {yields} AlNi{sub 3} and the final products were AlNi and AlNi{sub 3} phases. The shear strength of the joint was tested and the experimental results suggested that the application of Al/Ni multilayers improved the joining quality. - Highlights: Black-Right-Pointing-Pointer Diffusion bonding of TiAl to TiC cermet was realized using Al/Ni multilayer. Black-Right-Pointing-Pointer The reaction sequence of the Al/Ni multilayers was Al{sub 3}Ni {yields} Al{sub 3}Ni{sub 2} {yields} AlNi {yields} AlNi{sub 3}. Black-Right-Pointing-Pointer The interfacial microstructure of the joint was clarified. Black-Right-Pointing-Pointer The application of Al/Ni multilayers improved the joining quality.

Effects of C+ ion implantation on electrical properties of NiSiGe/SiGe contacts

International Nuclear Information System (INIS)

Zhang, B.; Yu, W.; Zhao, Q.T.; Buca, D.; Breuer, U.; Hartmann, J.-M.; Holländer, B.; Mantl, S.; Zhang, M.; Wang, X.

2013-01-01

We have investigated the morphology and electrical properties of NiSiGe/SiGe contact by C + ions pre-implanted into relaxed Si 0.8 Ge 0.2 layers. Cross-section transmission electron microscopy revealed that both the surface and interface of NiSiGe were improved by C + ions implantation. In addition, the effective hole Schottky barrier heights (Φ Bp ) of NiSiGe/SiGe were extracted. Φ Bp was observed to decrease substantially with an increase in C + ion implantation dose

Electrodeposition of amorphous Ni-P coatings onto Nd-Fe-B permanent magnet substrates

Energy Technology Data Exchange (ETDEWEB)

Ma, C.B [Department of Chemistry, Yuquan campus, Zhejiang University, Hangzhou 310027 (China); Cao, F.H [Department of Chemistry, Yuquan campus, Zhejiang University, Hangzhou 310027 (China); Zhang, Z. [Department of Chemistry, Yuquan campus, Zhejiang University, Hangzhou 310027 (China)]. E-mail: eaglezzy@zjuem.zju.edu.cn; Zhang, J.Q [Department of Chemistry, Yuquan campus, Zhejiang University, Hangzhou 310027 (China); State Key Laboratory for Corrosion and Protection of Metals, Institute of Metal Research, The Chinese Academy of Sciences, Shenyang 110016 (China)

2006-12-15

Decorative and protective Ni-P amorphous coatings were electroplated onto NdFeB permanent magnet from an ortho-phosphorous acid contained bath. The influences of the main electroplating technological parameters including current density, bath pH, bath temperature and H{sub 3}PO{sub 3} on the structure and chemical composition of Ni-P coatings were investigated by potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) techniques in conjunction with X-ray diffraction (XRD), scanning transmission electron microscopy (SEM) and X-ray energy-dispersive spectrometry (EDX). The optimized amorphous Ni-P coated NdFeB can stand for ca. 180 h against neutral 3.0 wt.% NaCl salt spray without any pitting corrosion. Meanwhile, the results also showed that large phosphorous content is the precondition for Ni-P coatings to possess the amorphous structure, but too much high phosphorous content can damage the amorphous structure due to the separation of superfluous P from Ni{sub 2}P/Ni{sub 3}P and the resultant formation of multi-phase coatings (such as Ni{sub 2}P-P)

The effect of pH on the corrosion behavior of intermetallic compounds Ni{sub 3}(Si,Ti) and Ni{sub 3}(Si,Ti) + 2Mo in sodium chloride solutions

Energy Technology Data Exchange (ETDEWEB)

Priyotomo, Gadang, E-mail: gada001@lipi.go.id; Nuraini, Lutviasari, E-mail: Lutviasari@gmail.com [Research Center for Metallurgy and Material, Indonesian Institute of Sciences, Kawasan PUSPIPTEK Gd.474, Setu, Tangerang Selatan, Banten 15314 (Indonesia); Kaneno, Yasuyuki, E-mail: kaneno@mtr.osakafu-u.ac.id [Department of Materials Science, Graduate School of Engineering, Osaka Prefecture University, 1-1 Gakuen-cho, Sakai, Osaka 599-8531 (Japan)

2015-12-29

The corrosion behavior of the intermetallic compounds, Ni{sub 3}(Si,Ti) (L1{sub 2}: single phase) and Ni{sub 3}(Si,Ti) + 2Mo (L1{sub 2} and (L12 + Ni{sub ss}) mixture region), has been investigated using an immersion test, electrochemical method and surface analytical method (SEM; scanning electron microscope and EDAX: Energy Dispersive X-ray) in 0.5 kmol/m{sup 3} NaCl solutions at various pH. The corrosion behavior of nickel alloy C-276 was studied under the same experimental conditions as a reference. It was found that the uniform attack was observed on Ni{sub 3}(Si,Ti) for the immersion test at lower pH, while the pitting attack was observed on this compound for this test at neutral solution. Furthermore, Ni{sub 3}(Si,Ti)+2Mo had the preferential dissolution of L1{sub 2} compared to (L1{sub 2} + Ni{sub ss}) mixture region at lower pH, while pitting attack occurred in (L1{sub 2} + Ni{sub ss}) mixture region at neutral solution. For both intermetallic compounds, the magnitude of pitting and uniform attack decrease with increasing pH of solutions. From the immersion test and polarization curves, the corrosion resistance of Ni{sub 3}(Si,Ti)+2Mo is lower than that of Ni{sub 3}(Si,Ti), while the nickel alloy C-276 is the highest one at various pH of solutions. On the other hand, in the lower pH of solutions, the corrosion resistance of tested materials decreased significantly compared to those in neutral and higher pH of solutions.

Characterization and thermal behavior of PrMO{sub 3} (M = Co or Ni) ceramic materials obtained from gelatin

Energy Technology Data Exchange (ETDEWEB)

Aquino, F.M., E-mail: flavyma@hotmail.com [Federal University of Rio Grande of Norte, Laboratory of Catalysis and Refining – NUPRAR, Av. Senador Salgado Filho, 3000, CEP 59078-970, Natal-RN (Brazil); Melo, D.M.A. [Federal University of Rio Grande of Norte, Laboratory of Catalysis and Refining – NUPRAR, Av. Senador Salgado Filho, 3000, CEP 59078-970, Natal-RN (Brazil); Pimentel, P.M. [Universidade Federal Rural do Semi-Árido, Campus Angicos, CEP 59515-000, Angicos-RN (Brazil); Braga, R.M.; Melo, M.A.F.; Martinelli, A.E.; Costa, A.F. [Federal University of Rio Grande of Norte, Laboratory of Catalysis and Refining – NUPRAR, Av. Senador Salgado Filho, 3000, CEP 59078-970, Natal-RN (Brazil)

2012-09-15

Graphical abstract: The micrograph in figure shows sample calcined at temperature 900 °C. The sample exhibits morphology with considerable porosity and the formation of agglomerated nanometric particles. Gelatin provides the system with a large amount of organic matter, which is then removed during calcinations, favoring the appearance of pores in the material. Highlights: ► Oxides with PrNiO{sub 3} and PrCoO{sub 3} were prepared by new method synthesis. ► The gelatin, through its carboxylate groups and amine, is an efficient director. ► The obtained materials have magnetic properties and application in catalysis. ► The decomposition kinetic study of bonding groups of gelatin with metallic ions that takes part in the synthesis of PrMO{sub 3}. -- Abstract: Metal oxides with perovskite-type structure have attracted considerable interest in recent years due to their magnetic and electrical properties, as well as their catalytic activity. In this study, oxides with PrNiO{sub 3} and PrCoO{sub 3} composition were prepared by using gelatin powder as a precursor agent for its use as a catalyst. The powders obtained were calcined at 700 °C and 900 °C and characterized using the X-ray diffraction, thermal analysis (thermogravimetry and differential thermal analysis), infrared spectroscopy, temperature programed reduction and scanning electron microscopy techniques. Thermogravimetric data using the non-isothermal kinetic models of Flynn and Wall and “Model-free Kinetics” were used to determine the activation energy to study the decomposition kinetics of the ligand groups with system's metallic ions that takes part in the synthesis of PrMO{sub 3} (M = Ni or Co).

Molecular dynamics simulation of graphene growth at initial stage on Ni(100) facet for low flux C energy by CVD

Energy Technology Data Exchange (ETDEWEB)

Syuhada, Ibnu, E-mail: ibnu-syuhada-p3@yahoo.com; Rosikhin, Ahmad, E-mail: aulia-fikri-h@yahoo.co.id; Fikri, Aulia, E-mail: a.rosikhin86@yahoo.co.id; Noor, Fatimah A., E-mail: fatimah@fi.itb.ac.id; Winata, Toto, E-mail: toto@fi.itb.ac.id [Departement of Physics, Institute of Technology Bandung, Tamansari 64 Street, East Java (Indonesia)

2016-02-08

In this study, atomic simulation for graphene growth on Ni (100) at initial stage via chemical vapor deposition method has been developed. The C-C atoms interaction was performed by Terasoff potential mean while Ni-Ni interaction was specified by EAM (Embedded Atom Modified). On the other hand, we used very simple interatomic potential to describe Ni-C interaction during deposition process. From this simulation, it shows that the formation of graphene is not occurs through a combined deposition mechanism on Ni substrate but via C segregation. It means, Ni-C amorphous is source for graphene growth when cooling down of Ni substrate. This result is appropriate with experiments, tight binding and quantum mechanics simulation.

Influence of Pr in the microstructure and electrical properties in LaPrMgAlMnCoNi based alloys for using for Ni-MH batteries

International Nuclear Information System (INIS)

Galdino, Gabriel Souza

2011-01-01

The La 0.7-x Pr x Mg 0.3 Al 0.3 Mn- 0.4 Co 0.5 Ni 3.8 (x= 0 a 0.7) as-cast alloys to apply in negative electrodes for nickel-metal hydride batteries (Ni-MH). The characterizations of the alloys were realized by: scanning electron microscope (SEM), energy dispersive spectrometry (EDS) and X-ray diffraction techniques. A study of hydrogen absorption capacity of the alloys realized. The hydrogenation of the material was performed in two processes: the low pressure (0.2 MPa of hydrogen and temperature of the 773 K) and high pressure (1 MPa of hydrogen and temperature of the 298 K). It was observed that with increasing Pr content occurred a decrease the hydrogen absorption capacity. The capacity of discharge of the batteries was determined utilizing an analyzer digital computerized composed of four channels. It was observed decreases of the discharge capacity of the batteries when increase praseodymium content in La 0.7- x Pr x Mg 0.3 Al 0.3 Mn 0.4 Co 0.5 Ni-3 .8 (x= 0 a 0.3) alloys. The highest discharge capacity (386 mAhg -1 ) and stability cyclic were obtained to La 0.2 Pr 0.5 Mg 0.3 Al 0.3 Mn 0.4 Co 0.5 Ni 3.8 alloy. This capacity can be related to the higher proportion of phase LaMg 2 Ni 9 in the alloy with the addition of 0.5 at.% Pr. (author)

Investigation into the MgF2-NiF2, CaF2-NiF2, SrF2-NiF2 systems

International Nuclear Information System (INIS)

Ikrami, D.D.; Petrov, S.V.; Fedorov, P.P.; Ol'khovaya, L.A.; Luginina, A.A.; AN SSSR, Moscow. Inst. Fizicheskikh Problem; AN SSSR, Moscow. Inst. Kristallografii)

1984-01-01

Using the methods of differential thermal and X-ray phase analyses the systems MgF 2 -NiF 2 , CaF 2 -NiF 2 , SrF 2 -NiF 2 have been studied. In the system SrF 2 -NiF 2 the only orthorhombic compounds SrNiF 4 (a=14.43; b=3.93; c=5.66 (+-0.01 A)) is formed. SrNiF 4 density constitutes: dsub(X-ray)=4.60+-0.01 g/cm 3 , dsub(exp.)=4.60+-0.03 g/cm 3 . Refraction indices are as follows SrNiF 4 :Ng=1.500; Nsub(m)=1.497; Nsub(p)=1.479. SrNiF 4 magnetic ordering temperature Tsub(N) approximately 100 K

Core-shell Ni0.5TiOPO4/C composites as anode materials in Li ion batteries

International Nuclear Information System (INIS)

Zhang, X.J.; Zhang, Y.; Zhou, Z.; Wei, J.P.; Essehli, R.; Bali, B. El

2011-01-01

Pristine Ni 0.5 TiOPO 4 was prepared via a traditional solid-state reaction, and then Ni 0.5 TiOPO 4 /C composites with core-shell nanostructures were synthesized by hydrothermally treating Ni 0.5 TiOPO 4 in glucose solution. X-ray diffraction patterns indicate that Ni 0.5 TiOPO 4 /C crystallizes in monoclinic P2 1 /c space group. Scanning electron microscopy and transmission electron microscopy show that the small particles with different sizes are coated with uniform carbon film of ∼3 nm in thickness. Raman spectroscopy also confirms the presence of carbon in the composites. Ni 0.5 TiOPO 4 /C composites presented a capacity of 276 mAh g -1 after 30 cycles at the current density of 42.7 mA g -1 , much higher than that of pristine Ni 0.5 TiOPO 4 (155 mAh g -1 ). The improved electrochemical performances can be attributed to the existence of carbon shell.

Microstructure of reactive synthesis TiC/Cr18Ni8 stainless steel bonded carbides

Institute of Scientific and Technical Information of China (English)

Jiang Junsheng; Liu Junbo; Wang Limei

2008-01-01

TiC/Cr18Ni8 steel bonded carbides were synthesized by vacuum sintering with mixed powders of iron, ferrotitanium, ferrochromium, colloidal graphite and nickel as raw materials. The microstructure and microhardness of the steel bonded carbides were analyzed by scanning electron microscope (SEM),X-ray diffraction (XRD) and Rockwell hardometer. Results show that the phases of steel bonded carbides mainly consist of TiC and Fe-Cr-Ni solid solution. The synthesized TiC particles are fine. Most of them are not more than 1 μm With the increase of sintering temperature, the porosity of TiC/Cr18Ni8 steel bonded carbides decreases and the density and hardness increase, but the size of TiC panicles slightly increases. Under the same sintering conditions, the density and hardness of steel bonded carbides with C/Ti atomic ratio 0.9 are higher than those with C/Ti atomic ratio 1.0.The TiC particles with C/Ti atomic ratio 0.9 are much finer and more homogeneous.

Magnetism and local environment model in (Ni/sub 1-c/Co/sub c/)078P014B008 amorphous alloys

International Nuclear Information System (INIS)

Amamou, A.

1976-06-01

The magnetic properties of amorphous alloys (Ni/sub 1-c/Co/sub c/) 0 . 78 P 0 . 14 B 0 . 08 were investigated. The samples were prepared by the splat-cooling method. The Curie temperatures were determined and the magnetization measurements, performed for 1.7 0 K less than or equal to T less than or equal to 270 0 K and fields up to kOe. Ni 0 . 78 P 0 . 14 B 0 . 08 is paramagnetic, whereas Co 0 . 78 P 0 . 14 B 0 . 08 is ferromagnetic until the crystallization temperature (678 0 K). The average moment per cobalt atom is 1.15 μ/sub B/. In (Ni/sub 1-c/Co/sub c/) 0 . 78 P 0 . 14 B 0 . 08 the critical concentration for the paramagnetic-ferromagnetic transition is c approximately equal to 0.15; this transition occurs in an inhomogeneous way. The saturation magnetization in the whole concentration range can be interpreted (as for some crystallized alloys and compounds) by a local environment model, when a reasonable short-range order is assumed. In such a model the magnetic moment per cobalt atom is related merely to the number of its Co first neighbors n/sub Co/. For n/sub Co/ = 0 and 1 the cobalt atom is not magnetic, for n/sub Co/ = 2 and 3 it carries a small moment μ 1 = 0.50μ/sub B/ and for n/sub Co/ greater than 3 it is magnetic with μ 2 = 1.15μ/sub B/ as in Co 0 . 78 P 0 . 14 B 0 . 08 ; the nickel atoms do not carry a substantial moment in the entire concentration range. These features are comparable to those obtained in some crystalline alloys. 3 figures

Microstructural evolution of Ni40Zr60 alloy during early stage of mechanical alloying of intermetallic compounds NiZr2 and Ni11Zr9

International Nuclear Information System (INIS)

Lee Peeyew; Koch, C.C.

1994-01-01

The microstructural change of Ni 40 Zr 60 alloy during mechanical alloying of mixtures of the intermetallic compounds NiZr 2 and Ni 11 Zr 9 has been studied by transmission electron microscopy. A specific ''cauliflower'' phase was formed during early stage of mechanical alloying process. It is suggested that the solid state reaction between intermetallic compounds NiZr 2 and Ni 11 Zr 9 is not the only origin for the formation of the ''cauliflower'' phase. ((orig.))

Thermal stability and electrical characteristics of NiSi films with electroplated Ni(W) alloy

International Nuclear Information System (INIS)

Xin Yuhang; Hu Anmin; Li Ming; Mao Dali

2011-01-01

In this study, an electroplating method to deposited Ni, crystalline NiW(c-NiW), amorphous NiW (a-NiW) films on P-type Si(1 0 0) were used to form Ni-silicide (NiSi) films. After annealed at various temperatures, sheet resistance of Ni/Cu, c-NiW/Cu and a-NiW/Cu was measured to observe the performance of those diffusion barrier layers. With W added in the barrier layer, the barrier performance was improved. The results of XRD and resistance measurement of the stacked Si/Ni(W)/Cu films reveal that Cu atom could diffuse through Ni barrier layer at 450 deg. C, could diffuse through c-NiW at 550 deg. C, but could hardly diffuse through a-NiW barrier layer. c-NiW layer has a better barrier performance than Ni layer, meanwhile the resistance is lower than a-NiW layer.

Electron spin resonance of Gd in the nuclear cooling agent: PrNi5 single crystals

International Nuclear Information System (INIS)

Levin, R.; Davidov, D.; Grayevsky, A.; Shaltiel, D.; Zevin, V.

1980-01-01

The ESR of Gd in single crystals of PrNi 5 is observed to exhibit significant angular dependence of the resonance position and linewidth at low temperatures. This is interpreted in terms of the axial spin Hamiltonian which takes the anisotropic susceptibility and the Gd-Pr exchange into consideration. From lineshape analysis the axial crystal field parameter and isotropic Gd-Pr exchange are derived. The Gd ESR linewidth increases with temperature; the thermal broadening is angularly dependent. This is similar to that observed for the Pr NMR in PrNi 5 single crystals. Both the NMR and ESR thermal broadenings are attributed to low-frequency fluctuations of the Pr ions induced by the Pr-Pr exchange coupling. A model for hexagonal Van-Vleck compounds is given and with the linewidth enables the Pr-Pr exchange coupling, under the assumption of a Gaussian or a Lorenzian distribution of the low-frequency fluctuation spectra, to be extracted. It is suggested that the angular dependence of the ESR thermal broadening is due to the Gd-Pr exchange coupling. (UK)

Thermochromic effect in NdNiO{sub 3-{delta}} thin films annealed in ambient air

Energy Technology Data Exchange (ETDEWEB)

Capon, F; Horwat, D; Pierson, J F [Institut Jean Lamour, Departement CP2S, (UMR CNRS 7198), Ecole des Mines, Parc de Saurupt, CS 14234, 54042 Nancy Cedex (France); Zaghrioui, M; Laffez, P, E-mail: fabien.capon@mines.inpl-nancy.f [Universite de Tours, IUT de Blois, Laboratoire d' Electrodynamique des Materiaux Avances, UMR CNRS CEA 6187, Place Jean Jaures, 41029 Blois cedex (France)

2009-09-21

The synthesis of NdNiO{sub 3} perovskite structure was achieved by soft post deposition annealing of initially amorphous thin films reactively sputter deposited on silicon substrates. The physical measurements were fully consistent with the properties expected for the thermochromic NdNiO{sub 3} phase. Upon heating, the optical transmission that was correlated with the electrical properties decreased in the infrared domain showing a thermochromic effect in this optical region. The metal-insulator transition temperature was found to be -68 {sup 0}C for the specimen tested and the jump in resistance at the transition was 1.4 orders of magnitude. The state-of-the-art methods that normally involve an annealing at a high oxygen pressure (200 x 10{sup 5} Pa) or epitaxial stabilization were considerably improved in this work by the use of dc sputtering and the optimization of the deposition conditions. Therefore, the novel soft process proposed here opens up numerous research possibilities. (fast track communication)

Magnetic Properties of Porous Metal-Organic Frameworks: Ni2(BODC)2(TED) and Ni2(BDC)2(TED)

Science.gov (United States)

Hamida, Youcef; Danilovic, Dusan; Lin, Chyan; Yuen, Tan; Li, Kunhao; Padmanabhan, Moothetty; Li, Jing

2010-03-01

Results of χ(T), M(H), and heat capacity C(T) measurements on two Ni dimer based porous materials Ni2(BODC)2(TED) and Ni2(BDC)2(TED) are reported. These materials form a tetragonal crystal structure of space group P4/ncc with a=b = 14.9 å and c = 19.4 å and Ni-Ni separation of 2.61å within the dimer. Magnetic data of Ni2(BODC)2(TED) revealed a ferromagnetic-like transition at about 17 K with θ = 8 K, and a coercivity field of 1700 G was observed in the hysteresis curve. Though isostructural to Ni2(BODC)2(TED), χ(T) and M(H) results of Ni2(BDC)2(TED) showed an antiferromagnetic transition at 10 K with θ = - 132 K, and no hysteresis was observed. Although specific heat data C(T) showed no clear transition in both compounds, nonlinear behavior is clearly seen in C/T vs. T plots, and a fit to the electron and phonon contributions to C(T) gives a large heavy-fermion-like γ in both cases. A model for the magnetic interactions is proposed and a comparison to the Cu and Co analogues is also made.

Ab-initio thermodynamic and elastic properties of AlNi and AlNi3 intermetallic compounds

Science.gov (United States)

Yalameha, Shahram; Vaez, Aminollah

2018-04-01

In this paper, thermodynamic and elastic properties of the AlNi and AlNi3 were investigated using density functional theory (DFT). The full-potential linearized augmented plane-wave (APW) in the framework of the generalized gradient approximation as used as implemented in the Wien2k package. The temperature dependence of thermal expansion coefficient, bulk modulus and heat capacity in a wide range of temperature (0-1600 K) were investigated. The calculated elastic properties of the compounds show that both intermetallic compounds of AlNi and AlNi3 have surprisingly negative Poisson’s ratio (NPR). The results were compared with other experimental and computational data.

Hydrodeoxygenation of lignin-derived phenolic compounds to hydrocarbons over Ni/SiO2-ZrO2 catalysts.

Science.gov (United States)

Zhang, Xinghua; Zhang, Qi; Wang, Tiejun; Ma, Longlong; Yu, Yuxiao; Chen, Lungang

2013-04-01

Inexpensive non-sulfided Ni-based catalysts were evaluated for hydrodeoxygenation (HDO) using guaiacol as model compound. SiO2-ZrO2 (SZ), a complex oxide synthesized by precipitation method with different ratio of Si/Zr, was impregnated with Ni(NO3)2·6H2O and calcined at 500°C. Conversion rates and product distribution for guaiacol HDO at 200-340°C were determined. Guaiacol conversion reached the maximum at 300°C in the presence of Ni/SZ-3. When HDO reaction was carried out with real lignin-derived phenolic compounds under the optimal conditions determined for guaiacol, the total yield of hydrocarbons was 62.81%. These hydrocarbons were comprised of cyclohexane, alkyl-substituted cyclohexane and alkyl-substituted benzene. They have high octane number, would be the most desirable components for fungible liquid transportation fuel. Copyright © 2013 Elsevier Ltd. All rights reserved.

Discovery of a thermally persistent h.c.p. solid-solution phase in the Ni-W system

International Nuclear Information System (INIS)

Kurz, S. J. B.; Leineweber, A.; Maisel, S. B.; Höfler, M.; Müller, S.; Mittemeijer, E. J.

2014-01-01

Although the accepted Ni-W phase diagram does not reveal the existence of h.c.p.-based phases, h.c.p.-like stacking sequences were observed in magnetron-co-sputtered Ni-W thin films at W contents of 20 to 25 at. %, by using transmission electron microscopy and X-ray diffraction. The occurrence of this h.c.p.-like solid-solution phase could be rationalized by first-principles calculations, showing that the vicinity of the system's ground-state line is populated with metastable h.c.p.-based superstructures in the intermediate concentration range from 20 to 50 at. % W. The h.c.p.-like stacking in Ni-W films was observed to be thermally persistent, up to temperatures as high as at least 850 K, as evidenced by extensive X-ray diffraction analyses on specimens before and after annealing treatments. The tendency of Ni-W for excessive planar faulting is discussed in the light of these new findings

Improvement of the tool life of a micro-end mill using nano-sized SiC/Ni electroplating method.

Science.gov (United States)

Park, Shinyoung; Kim, Kwang-Su; Roh, Ji Young; Jang, Gyu-Beom; Ahn, Sung-Hoon; Lee, Caroline Sunyong

2012-04-01

High mechanical properties of a tungsten carbide micro-end-mill tool was achieved by extending its tool life by electroplating nano-sized SiC particles (electroplating method on the surface of the micro-end-mill tool was applied using SiC particles and Ni particles. Organic additives (saccharin and ammonium chloride) were added in a Watts bath to improve the nickel matrix density in the electroplating bath and to smooth the surface of the co-electroplating. The morphology of the coated nano-sized SiC particles and the composition were measured using Scanning Electron Microscope and Energy Dispersive Spectrometer. As the Ni/SiC co-electroplating layer was applied, the hardness and friction coefficient improved by 50%. Nano-sized SiC particles with 7 wt% were deposited on the surface of the micro-end mill while the Ni matrix was smoothed by adding organic additives. The tool life of the Ni/SiC co-electroplating coating on the micro-end mill was at least 25% longer than that of the existing micro-end mills without Ni/SiC co-electroplating. Thus, nano-sized SiC/Ni coating by electroplating significantly improves the mechanical properties of tungsten carbide micro-end mills.

Experimental investigation of phase equilibria in the Co-Ni-Zr ternary system

Energy Technology Data Exchange (ETDEWEB)

Liu, Xingjun; Yang, Shuiyuan; Yu, Wenjie; Wang, Cuiping [Xiamen Univ. (China). Fujian Key Laboratory of Materials Genome; Xiong, Huaping; Cheng, Yaoyong; Wu, Xin [Beijing Institute of Aeronautical Materials (China). Div. of Welding and Forging

2016-10-15

The phase equilibria of the Co-Ni-Zr ternary system at 1 000 C, 1 100 C and 1 200 C were experimentally investigated by means of back-scattered electron imaging, electron probe microanalysis and X-ray diffraction on the equilibrated ternary alloys. In this study, no ternary compound is found. The (αCo, Ni) phase region extends from the Ni-rich corner to the Co-rich corner with small solubility of Zr at three sections. At 1 000 C and 1 100 C, Ni{sub 5}Zr, Co{sub 2}Zr and Ni{sub 10}Zr{sub 7} phases have large solid solution ranges, but Ni{sub 10}Zr{sub 7} phase disappears at 1 200 C. The Ni{sub 7}Zr{sub 2}, NiZr, Co{sub 11}Zr{sub 2}, Co{sub 23}Zr{sub 6} and CoZr phases exhibit nearly linear compounds in the studied sections, and have large composition ranges. Additionally, some differences in phase relationship exist among the above three isothermal sections.

Thermal stability of Ni/Ti/Al ohmic contacts to p-type 4H-SiC

Energy Technology Data Exchange (ETDEWEB)

Yu, Hailong; Shen, Huajun, E-mail: shenhuajun@ime.ac.cn; Tang, Yidan; Bai, Yun; Liu, Xinyu [Microwave Device and IC Department, Institute of Microelectronics of Chinese Academy of Sciences, Beijing 100029 (China); Zhang, Xufang [School of Physical Science and Technology, Lanzhou University, Lanzhou 730000 (China); Wu, Yudong; Liu, Kean [Zhuzhou CSR Times Electric Co., Ltd, ZhuZhou 412001 (China)

2015-01-14

Low resistivity Ni/Ti/Al ohmic contacts on p-type 4H-SiC epilayer were developed, and their thermal stabilities were also experimentally investigated through high temperature storage at 600 °C for 100 h. The contact resistance of the Al/Ti/Ni/SiC contacts degraded in different degrees, and the contact morphology deteriorated with the increases of the average surface roughness and interface voids. X-ray spectra showed that Ni{sub 2}Si and Ti{sub 3}SiC{sub 2}, which were formed during ohmic contact annealing and contributed to low contact resistivity, were stable under high temperature storage. The existence of the TiAl{sub 3} and NiAl{sub 3} intermetallic phases was helpful to prevent Al agglomeration on the interface and make the contacts thermally stable. Auger electron spectroscopy indicated that the incorporation of oxygen at the surface and interface led to the oxidation of Al or Ti resulting in increased contact resistance. Also, the formation of these oxides roughened the surface and interface. The temperature-dependence of the specific contact resistance indicated that a thermionic field emission mechanism dominates the current transport for contacts before and after the thermal treatment. It suggests that the Ni/Ti/Al composite ohmic contacts are promising for SiC devices to be used in high temperature applications.

Phase Equilibria of the Sn-Ni-Si Ternary System and Interfacial Reactions in Sn-(Cu)/Ni-Si Couples

Science.gov (United States)

Fang, Gu; Chen, Chih-chi

2015-07-01

Interfacial reactions in Sn/Ni-4.5 wt.%Si and Sn-Cu/Ni-4.5 wt.%Si couples at 250°C, and Sn-Ni-Si ternary phase equilibria at 250°C were investigated in this study. Ni-Si alloys, which are nonmagnetic, can be regarded as a diffusion barrier layer material in flip chip packaging. Solder/Ni-4.5 wt.%Si interfacial reactions are crucial to the reliability of soldered joints. Phase equilibria information is essential for development of solder/Ni-Si materials. No ternary compound is present in the Sn-Ni-Si ternary system at 250°C. Extended solubility of Si in the phases Ni3Sn2 and Ni3Sn is 3.8 and 6.1 at.%, respectively. As more Si dissolves in these phases their lattice constants decrease. No noticeable ternary solubility is observed for the other intermetallics. Interfacial reactions in solder/Ni-4.5 wt.%Si are similar to those for solder/Ni. Si does not alter the reaction phases. No Si solubility in the reaction phases was detected, although rates of growth of the reaction phases were reduced. Because the alloy Ni-4.5 wt.%Si reacts more slowly with solders than pure Ni, the Ni-4.5 wt.%Si alloy could be a potential new diffusion barrier layer material for flip chip packaging.

Structural and Mechanical Properties of the ZrC/Ni-Nanodiamond Coating Synthesized by the PVD and Electroplating Processes for the Cutting Knifes

Science.gov (United States)

Chayeuski, V.; Zhylinski, V.; Cernashejus, O.; Visniakov, N.; Mikalauskas, G.

2018-04-01

In this work, combined gradient ZrC/Ni-nanodiamond ultradispersed diamonds (UDD) coatings were synthesized on the surface of knife blades made of hard alloy WC-2 wt.% Co by electroplating and cathode arc evaporation PVD techniques to increase the durability period of a wood-cutting milling tool. The microstructure, phase and elemental composition, microhardness, and adhesion strength of the coatings were investigated. Ni-UDD layer is not mixed with the ZrC coating and hard alloy substrate. Cobalt is present in Ni-UDD layer after deposition of ZrC. The ZrC/Ni-nanodiamond coating consists of separate phases of zirconium carbide (ZrC), α-Ni, and Ni-UDD. The maximum value of microhardness of the Ni-nanodiamond coating is 5.9 GPa. The microhardness value of the ZrC/Ni-nanodiamond coatings is 25 ± 6 GPa, which corresponds to the microhardness of the hard alloy substrate and ZrC coating. The obtained high values of the critical loads on the scratch track of the ZrC/Ni-nanodiamond coating in 24 N prove a sufficiently high value of the adhesion strength of the bottom Ni-UDD layer with WC-Co substrate. Pilot testing of ZrC/Ni-nanodiamond-coated cutting tools proved their increasing durability period to be 1.5-1.6 times higher than that of bare tools, when milling laminated chipboard.

Characterization of the N-methoxyindole-3-carbinol (NI3C)–Induced Cell Cycle Arrest in Human Colon Cancer Cell Lines

DEFF Research Database (Denmark)

Neave, Antje S.; Sarup, Sussi; Seidelin, Michel

2005-01-01

Recent results have shown that indole-3-carbinol (I3C) inhibits the cellular growth of human cancer cell lines. In some cruciferous vegetables, another indole, N-methoxyindole-3-carbinol (NI3C), is found beside I3C. Knowledge about the biological effects of NI3C is limited. The aim of the present...... study was to show the effect of NI3C on cell growth of two human colon cancer cell lines, DLD-1 and HCT-116. For the first time it is shown that NI3C inhibits cellular growth of DLD-1 and HCT-116 and that NI3C is a more potent inhibitor of cell proliferation than I3C. In addition to the inhibition...... of cellular proliferation, NI3C caused an accumulation of HCT-116 cells in the G2/M phase, in contrast to I3C, which led to an accumulation of the colon cells in G0/G1 phase. Furthermore, NI3C delays the G1-S phase transition of synchronized HCT-116 cells. The indole-mediated cell-cycle arrest may be related...

Core/shell AgNi/PtAgNi nanoparticles as methanol-tolerant oxygen reduction electrocatalysts

International Nuclear Information System (INIS)

Wu, Dengfeng; Cheng, Daojian

2015-01-01

A core/shell AgNi/PtAgNi nanoparticle (NP) was synthesized via a new seed-mediated growth method in organic solvent medium. The as-synthesized AgNi/PtAgNiNP exhibits an AgNi core coated with PtAgNi shell, which was confirmed by transmission electron microscopy (TEM), ultraviolet–visible absorption spectroscopy and X-ray Photoelectron Spectroscopy (XPS). The AgNi/PtAgNiNPs/C catalyst possesses higher oxygen reduction reaction (ORR) activity and better durability compared with the commercial Pt/C catalyst. It is found that the ORR polarization curve of the AgNi/PtAgNiNPs/C catalyst shows an onset potential of 0.91 V vs. RHE, which is superior to the commercial Pt/C (0.88 V vs. RHE). In addition, the AgNi/PtAgNiNPs/C catalyst shows much better durability than the commercial Pt/C catalyst. More interestingly, the AgNi/PtAgNiNPs/C catalyst displays much higher methanol tolerance than the commercial Pt/C catalyst in 0.1 M KOH solution in the presence of 0.5 M methanol. Our results show that core/shell AgNi/PtAgNiNPs possess selective activity for ORR even in the presence of methanol, showing potential application as methanol-tolerant cathode catalysts in direct methanol fuel cells.

The Influence of Sintering Temperature of Reactive Sintered (Ti, MoC-Ni Cermets

Directory of Open Access Journals (Sweden)

Marek Jõeleht

2015-09-01

Full Text Available Titanium-molybdenum carbide nickel cermets ((Ti, MoC-Ni were produced using high energy milling and reactive sintering process. Compared to conventional TiC-NiMo cermet sintering the parameters for reactive sintered cermets vary since additional processes are present such as carbide synthesis. Therefore, it is essential to acquire information about the suitable sintering regime for reactive sintered cermets. One of the key parameters is the final sintering temperature when the liquid binder Ni forms the final matrix and vacancies inside the material are removed. The influence of the final sintering temperature is analyzed by scanning electron microscopy. Mechanical properties of the material are characterized by transverse rupture strength, hardness and fracture toughness.DOI: http://dx.doi.org/10.5755/j01.ms.21.3.7179

Oxidation between 1000 degrees C and 1600 degrees C and limiting criteria for the use of Zr-doped β-NiAl and β/γ alloys

International Nuclear Information System (INIS)

Doychak, J.; Barrett, C.A.; Smialek, J.L.

1989-01-01

This paper reports the isothermal and cyclic oxidation behavior of Zr-doped β-NiAl and β/γ' intermetallic alloys studied over the temperature range 1000 degrees C-1600 degrees C. Isothermal scale growth was governed by γ-Al 2 O 3 growth kinetics. The scale growth rates showed no monotonic trends with alloy aluminum content, although the stoichiometric β-NiAl alloy had the slowest kinetics. Cyclic oxidation at 1200 degrees C for 1000, 1-hr cycles of alloys having less than approximately 40 at %Al was poor due to the formation of martensite and less protective Ni-containing oxides. The cyclic oxidation behavior of Zr-doped stoichiometric β-NiAl was poor beyond 100, 1-hr cycles at 1425 degrees C. Computer modeling of the cyclic oxidation results was performed to arrive at limiting criteria for alloy service life. The limiting criteria were based on alloy aluminum depletion by oxidation that is necessary for less protective Ni-containing oxide formation. The modelling and lifetime criteria were applied to the cyclic oxidation of a Ni-50.2Al-0.04Zr (at%) alloy

C-type Nd2Se3

Directory of Open Access Journals (Sweden)

2009-03-01

Full Text Available The title compound, neodymium sesquiselenide, is isotypic with the other known rare-earth metal(III selenides M2Se3 (M = La–Pr and Sm–Lu with the cubic C-type structure. It adopts a cation-defective Th3P4-type arrangement with close to 8/9 of the unique neodymium-cation site occupied, leading to the composition Nd2.667Se4 (Z = 4 or Nd2Se3 (Z = 5.333, respectively. The Nd3+ cations are thus surrounded by eight selenide anions, forming trigonal [NdSe8]13− dodecahedra, whereas the Se2− anions exhibit a sixfold coordination, but due to the under-occupation of neodymium, each one is statistically surrounded by only 5.333 cations. The crystal studied was a merohedral twin with a 0.31 (6:0.69 (6 domain ratio.

Self-assembled nano- to micron-size fibers from molten R11Ni4In9 intermetallics

Energy Technology Data Exchange (ETDEWEB)

Provino, Alessia; Manfrinetti, Pietro; Gschneidner, Karl A; Dhar, Sudesh K; Schlagel, Deborah L; Lograsso, Thomas A; Miller, Gordon J; Thimmaiah, Srinivasa; Wang, Hui; Russell, Alan M; Becker, Andrew; Mudryk, Yaroslav

2014-07-01

A study of the formation of Gd11M4In9 (M = Ni, Pd, Pt) and R11Ni4In9 (R = rare earth) compounds revealed a unique and peculiar property, which is to naturally crystallize in a bundle of self-assembled fibers when cooled from the melt. The fibers, which are nano- to millimeters in cross-section and approximate to 11-40 mm long, grow unidirectionally along a temperature gradient. These compounds adopt the orthorhombic Nd11Pd4In9 structure type (oC48-Cmmm). This structure is layered, with slabs of R atoms alternating with slabs of Ni/In atoms along a short c-axis (much shorter than either the a- or b-axis). The growth direction of the fibers is along the crystallographic c-axis, orthogonal to the a-b plane. Two strong and short In In bonds lie in the a-b plane, which are even shorter than in In metal. Integrated crystal orbital Hamilton population calculations show that the In In bonds create isolated "R8Ni4In9" rods growing along the c-axis, with the In In bonds being part of the rods. This appears to be an important factor explaining the microfibrous nature of these phases. Some physical properties have been measured on the Gd11Ni4In9 homolog. The compound orders ferrimagnetically at T-c approximate to 88 K, and at lower temperatures (46 and 10 K), two other magnetic anomalies were observed, probably due to spin reorientations. As expected from the bonding features, the mechanical, magnetic and electrical properties are strongly anisotropic. (C) 2014 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

Role of atomic bonding for compound and glass formation in Ni-Si, Pd-Si, and Ni-B systems

Science.gov (United States)

Tanaka, K.; Saito, T.; Suzuki, K.; Hasegawa, R.

1985-11-01

Valence electronic structures of crystalline compounds and glassy alloys of Ni silicides, Pd silicides, and Ni borides are studied by soft-x-ray spectroscopy over wide ranges of Si and B concentrations. The samples prepared include bulk compounds, glassy ribbons, and amorphous sputtered films. Silicon Kβ emissions of Ni and Pd silicides generally consist of a prominent peak fixed at ~=4.5 and ~=5.8 eV below the Fermi level EF, respectively, with a shoulder near EF which grows and shifts toward lower energy with increasing Si concentration. The former is identified as due to Si p-like states forming Si 3p-Ni 3d or Si 3p-Pd 4d bonding states while the latter as due to the corresponding antibonding states. Ni L3 and Pd L3 emissions of these silicides indicate that Ni 3d and Pd 4d states lie between the above two states. These local electronic configurations are consistent with partial-density-of-states (PDOS) calculations performed by Bisi and Calandra. Similar electronic configurations are suggested for Ni borides from B Kα and Ni L3 emissions. Differences of emission spectra between compounds and glasses of similar compositions are rather small, but some enhancement of the contribution of antibonding states to the PDOS near EF is suggested for certain glasses over that of the corresponding compounds. These features are discussed in connection with the compound stability and glass formability.

Isothermal analysis of intermetallic MmNi5-xAlx in air decomposition processes

International Nuclear Information System (INIS)

Obregon, S.A.; Andrade Gamboa, J.J.; Esquivel, M.R.

2012-01-01

In this paper, it is analyzed the behavior of the degree of reaction as function of time α (t) of a sample of MmNi 4.3 Al 0.7 (Mm mischmetal = La 0.25 Ce 0.52 Nd 0.17 Pr 0.06 ) at different temperatures. The curves were obtained by isothermal calorimetric techniques. As a result of this study, it was observed that the kinetics of intermetallic can be separated into two main stages. At temperatures below 350 o C, the first stage is the oxidation of Mm and Al. At temperatures over 400 o C, the oxidation of Ni is also produced parallel to the above mentioned reactions. But the kinetics of the last one is at least three orders of magnitude slower. It was also observed that no thermal event occurs below 180 o C. It indicates that the intermetallic do not react at temperatures below this temperature value (author)

Superstructure formation in PrNi{sub 2}Al{sub 3} and ErPd{sub 2}Al{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Eustermann, Fabian; Hoffmann, Rolf-Dieter [Muenster Univ. (Germany). Inst. fuer Anorganische und Analytische Chemie; Janka, Oliver [Muenster Univ. (Germany). Inst. fuer Anorganische und Analytische Chemie; Oldenburg Univ. (Germany). Inst. fuer Chemie

2017-09-01

The intermetallic phase ErPd{sub 2}Al{sub 3} was obtained by arc-melting of the elements and subsequent annealing for crystal growth. The sample was studied by X-ray diffraction on powders and single crystals. The structure of ErPd{sub 2}Al{sub 3} was refined from X-ray diffraction data and revealed a superstructure of PrNi{sub 2}Al{sub 3} - a CaCu{sub 5} derivative (P6/m, a=1414.3(1), c=418.87(3) pm wR=0.0820, 1060 F{sup 2} values, 48 variables). The same superstructure was subsequently found for PrNi{sub 2}Al{sub 3} (P6/m, a=1407.87(4), c=406.19(2) pm, wR=0.0499, 904 F{sup 2} values, 47 variables). In the crystal structure, the aluminium and transition metal atoms form a polyanionic network according to [T{sub 2}Al{sub 3}]{sup δ-}, while rare earth atoms fill cavities within the networks. They are coordinated by six transition metal and twelve aluminum atoms. In contrast to the PrNi{sub 2}Al{sub 3} type structure reported so far, two crystallographic independent rare-earth sites are found of which one (1b) is shifted by 1/2 z, causing a distortion in the structure along with a recoloring of the T and Al atoms in the network.

Experimental investigation of phase equilibria in the Zr-Cu-Ni ternary system

International Nuclear Information System (INIS)

Yang, Mujin; Wang, Cuiping; Yang, Shuiyuan; Shi, Zhan; Han, Jiajia; Liu, Xingjun

2017-01-01

The phase equilibria in the Zr-Cu-Ni ternary system are investigated combined with X-ray diffraction, electron probe micro-analysis and differential scanning calorimetry. Two isothermal sections of the Zr-Cu-Ni ternary system at 1 000 C and 1 100 C are experimentally established. Most of the binary intermetallic compounds, e.g. Zr 7 Ni 10 , ZrNi, ZrNi 5 , Zr 14 Cu 51 , and Zr 2 Cu 9 , show a remarkable ternary solubility. A new ternary compound named τ 3 (Zr 31.1-30.7 . Cu 28.5-40.3 Ni 40.4-29.0 ) is detected at 1 000 C and dissolved at 1 020 C because the nearby large liquid phase field further expands. The newly determined phase equilibria will provide important information for both thermodynamic assessment and alloy design of Zr-based metallic glass.

Crystal structure and phase transition studies in perovskite-type oxides using powder-diffraction techniques and symmetry-mode analysis : SrLnMRuO6 (Ln=La,Pr,Nd; M=Zn,Co,Mg,Ni,Fe) and ALn2CuTi2O9 (A=Ca,Ba; Ln=La,Pr,Nd,Sm)

OpenAIRE

Iturbe Zabalo, Edurne

2013-01-01

La tesis se ha centrado en la síntesis y caracterización estructural de materiales tipo perovskita: SrLnMRuO6 (Ln=La,Pr,Nd; M=Zn,Co,Mg,Ni,Fe) y ALn2CuTi2O9 (A=Ca,Ba; Ln=La,Pr,Nd,Sm). El estudio de las estructuras de los materiales se ha realizado mediante el análisis de los patrones de difracción en polvo de rayos-X, sincrotrón y/o neutrones. En el refinamiento por el método de Rietveld de las estructuras se han sustituido las coordenadas atómicas (el método más común), por coordenadas colect...

Communication: Surface-to-bulk diffusion of isolated versus interacting C atoms in Ni(111) and Cu(111) substrates: A first principle investigation.

Science.gov (United States)

Harpale, Abhilash; Panesi, Marco; Chew, Huck Beng

2015-02-14

Using first principle calculations, we study the surface-to-bulk diffusion of C atoms in Ni(111) and Cu(111) substrates, and compare the barrier energies associated with the diffusion of an isolated C atom versus multiple interacting C atoms. We find that the preferential Ni-C bonding over C-C bonding induces a repulsive interaction between C atoms located at diagonal octahedral voids in Ni substrates. This C-C interaction accelerates C atom diffusion in Ni with a reduced barrier energy of ∼1 eV, compared to ∼1.4-1.6 eV for the diffusion of isolated C atoms. The diffusion barrier energy of isolated C atoms in Cu is lower than in Ni. However, bulk diffusion of interacting C atoms in Cu is not possible due to the preferential C-C bonding over C-Cu bonding, which results in C-C dimer pair formation near the surface. The dramatically different C-C interaction effects within the different substrates explain the contrasting growth mechanisms of graphene on Ni(111) and Cu(111) during chemical vapor deposition.

A novel fluffy nanostructured 3D network of Ni(C7H4O5) for supercapacitors

International Nuclear Information System (INIS)

Chen, Qiulin; Lei, Shuijin; Chen, Lianfu; Deng, Peiqin; Xiao, Yanhe; Cheng, Baochang

2017-01-01

Highlights: • The fluffy 3D network of Ni(C 7 H 4 O 5 ) complex is firstly prepared on Ni foam. • The fluffy 3D network shows high areal capacitance and excellent cycle stability. • The fluffy network has large superior pseudocapacitive performance than the powder. • An asymmetric supercapacitor with high capacitance and energy density is assembled. - Abstract: Supercapacitors have raised considerable research interest in recent years due to their extensive potential application in next-generation energy storage. It is always of great importance to develop new electrode materials for supercapacitors so far. In this research, nickel gallate complex (Ni(C 7 H 4 O 5 )) nanostructures are successfully grown on nickel foam by a facile hydrothermal route, which can be directly used as the electrodes for supercapacitors. X-ray diffraction patterns show that the sample is amorphous. The scanning electron microscopy images reveal that the products consist of novel fluffy 3D network with a mass of fibers. The electrochemical measurements demonstrate that the prepared Ni(C 7 H 4 O 5 ) electrode possesses the specific capacitance of 3.688 F cm −2 (1229.3 F g −1 ) at a current density of 9 mA cm −2 (3 A g −1 ). It presents an excellent cycling stability with a capacitance retention of 87.9% after 5000 cycles even at a very high current density of 40 mA cm −2 . An asymmetric supercapacitor device is assembled using the Ni(C 7 H 4 O 5 ) sample as positive electrode and activated carbon as negative one. A high gravimetric capacitance of 71.4 F g −1 at a current density of 0.5 A g −1 can be achieved. The fabricated device delivers the highest energy density of 23.8 W h kg −1 at a power density of 388.2 W kg −1 with a voltage window of 1.55 V. This strategy should be extended to other organometallic compounds for supercapacitors.

HREEL study of c(53x9)rect-N structure on Ni(111) surface

International Nuclear Information System (INIS)

Papagno, M.; Pacile, D.; Giallombardo, C.; Cupolillo, A.; Papagno, L.

2005-01-01

In this work we have prepared and characterized by low energy electron diffraction (LEED) and high-resolution electron energy loss spectroscopy (HREELS) the Ni(111)-c(53x9)rect-N surface structure formed by saturating the Ni(111) surface with nitrogen atoms. This structure was obtained by the ion-gauge assisted N 2 exposure method. The loss spectra show features at 50 and 25meV assigned to the N-Ni vibration and to a phonon of the reconstructed surface, respectively. We also investigated the case in which the Ni(111) surface was covered with a low coverage of N atoms

A new BODIPY/nanoparticle/Ni affinity system for binding of cytochrome c

Energy Technology Data Exchange (ETDEWEB)

Maltas, Esra, E-mail: maltasesra@gmail.com [Selcuk University, Faculty of Science, Department of Chemistry, 42075 Konya (Turkey); Selcuk University, Faculty of Science, Department of Biochemistry, 42075 Konya (Turkey); Kursunlu, Ahmed Nuri [Selcuk University, Faculty of Science, Department of Chemistry, 42075 Konya (Turkey); Arslan, Gulsin [Selcuk University, Faculty of Science, Department of Biochemistry, 42075 Konya (Turkey); Selcuk University, Advanced Research Technology and Application Center, 42075 Konya (Turkey); Ozmen, Mustafa [Selcuk University, Faculty of Science, Department of Chemistry, 42075 Konya (Turkey); Selcuk University, Advanced Research Technology and Application Center, 42075 Konya (Turkey)

2015-09-15

Highlights: • BODIPY was synthesized, and then attached to magnetic nanoparticles. • Ni(II) ions were chelated on prepared material. • The binding of cytochrome c to obtained material was studied. - Abstract: In this study, 3,5-{Bis[4,4-difluoro, 8-(2,6-diethyl, 1,3,5,7-tetramethyl-4-bora-3a,4a-diaza-s-indacene)]}benzoylchloride (BODIPY) was synthesized for the improving of a new immobilized metal affinity supporting material. Firstly, the synthesized BODIPY was immobilized on iron oxide superparamagnetic nanoparticles (SPIONs) and then, Ni(II) ions were chelated with the active terminals of BODIPY on nanoparticles surfaces to prepare an immobilized metal affinity (IMA) adsorbent for protein adsorption. The amount of BODIPY coated on SPIONs was about 29.7 μM at 10 mg nanoparticles. 738 μmol of Ni(II) ions were loaded to 10 mg of the SPIONs/BODIPY. The binding amount of cytochrome c was found to be 170 μg to the SPIONs/BODIPY/Ni at pH 7.4. The binding amount of the molecules on SPIONs was analyzed by using UV–vis, fluorescence and atomic absorption spectroscopy. The characterization of the prepared surfaces was performed by FT-IR, SEM and TEM.

Crystal structures and magnetic properties of iron (III)-based phosphates: Na4NiFe(PO4)3 and Na2Ni2Fe(PO4)3

International Nuclear Information System (INIS)

Essehli, Rachid; Bali, Brahim El; Benmokhtar, Said; Bouziane, Khalid; Manoun, Bouchaib; Abdalslam, Mouner Ahmed; Ehrenberg, Helmut

2011-01-01

Graphical abstract: A perspective view of the Na 2 Ni 2 Fe(PO 4 ) 3 structure along the [0 0 1] direction. Both compounds seem to exibit antiferromagnetic interactions between magnetic entities at low temperature. Display Omitted Research highlights: → Nasicon and Alluaudite compounds, Iron(III)-based phosphates, Crystal structures of Na 4 NiFe(PO 4 ) 3 and Na 2 Ni 2 Fe(PO 4 ) 3 . → Magnetism behaviours of Na 4 NiFe(PO 4 ) 3 and Na 2 Ni 2 Fe(PO 4 ) 3 . → Antiferromagnetism interactions. → Mossbauer spectroscopy. - Abstract: Crystal structures from two new phosphates Na 4 NiFe(PO 4 ) 3 (I) and Na 2 Ni 2 Fe(PO 4 ) 3 (II) have been determined by single crystal X-ray diffraction analysis. Compound (I) crystallizes in a rhombohedral system (S. G: R-3c, Z = 6, a = 8.7350(9) A, c = 21.643(4) A, R 1 = 0.041, wR 2 =0.120). Compound (II) crystallizes in a monoclinic system (S. G: C2/c, Z = 4, a = 11.729(7) A, b = 12.433(5) A, c = 6.431(2) A, β = 113.66(4) o , R 1 = 0.043, wR 2 =0.111). The three-dimensional structure of (I) is closely related to the Nasicon structural type, consisting of corner sharing [(Ni/Fe)O 6 ] octahedra and [PO 4 ] tetrahedra forming [NiFe(PO 4 ) 3 ] 4+ units which align in chains along the c-axis. The Na + cations fill up trigonal antiprismatic sites within these chains. The crystal structure of (II) belongs to the alluaudite type. Its open framework results from [Ni 2 O 10 ] units of edge-sharing [NiO 6 ] octahedra, which alternate with [FeO 6 ] octahedra that form infinite chains. Coordination of these chains yields two distinct tunnels in which site Na + . The magnetization data of compound (I) reveal antiferromagnetic (AFM) interactions by the onset of deviations from a Curie-Weiss behaviour at low temperature as confirmed by Moessbauer measurements performed at 4.2 K. The corresponding temperature dependence of the reciprocal susceptibility χ -1 follows a typical Curie-Weiss behaviour for T > 105 K. A canted AFM state is proposed for

Structural characterization of half-metallic Heusler compound NiMnSb

Energy Technology Data Exchange (ETDEWEB)

Nowicki, L. E-mail: lech.nowicki@fuw.edu.pl; Abdul-Kader, A.M.; Bach, P.; Schmidt, G.; Molenkamp, L.W.; Turos, A.; Karczewski, G

2004-06-01

High resolution X-ray diffraction (HRXRD) and Rutherford backscattering/channeling (RBS/c) techniques were used to characterize layers of NiMnSb grown by molecular beam epitaxy (MBE) on InP with a In{sub x}Ga{sub 1-x}As buffer. Angular scans in the channeling mode reveal that the crystal structure of NiMnSb is tetragonally deformed with c/a=1.010{+-}0.002, in agreement with HRXRD data. Although HRXRD demonstrates the good quality of the pseudomorphic NiMnSb layers the channeling studies show that about 20% of atoms in the layers do not occupy lattice sites in the [0 0 1] rows of NiMnSb. The possible mechanisms responsible for the observed disorder are discussed.

Participar como niña o niño en el mundo social

Directory of Open Access Journals (Sweden)

Silvia Paulina Díaz

2010-01-01

Full Text Available En este artículo presento la participación como resultado de un trabajo investigativo realizado durante el año 2007, con niños y niñas escolarizados habitantes de la ciudad de Medellín, Colombia, cuyo objetivo fue analizar las representaciones sociales que ellos y ellas comparten sobre el ejercicio ciudadano. El análisis de la información tiene como ejes fundamentales, la salud colectiva, la sociología de la infancia y la participación en la niñez, en una aproximación que se realiza desde un enfoque cualitativo y etnográfico. En los hallazgos, sobresale cómo las niñas y niños se muestran preparados para ejercer su derecho a la participación como aspecto de sus vidas que se haría posible dentro del marco normativo existente, pero que aún no es asumido en prácticas sociales que los incluyan.

Participar como niña o niño en el mundo social

Directory of Open Access Journals (Sweden)

Silvia Paulina Díaz

2010-10-01

Full Text Available En este artículo presento la participación como resultado de un trabajo investigativo realizado durante el año 2007, con niños y niñas escolarizados habitantes de la ciudad de Medellín, Colombia, cuyo objetivo fue analizar las representaciones sociales que ellos y ellas comparten sobre el ejercicio ciudadano. El análisis de la información tiene como ejes fundamentales, la salud colectiva, la sociología de la infancia y la participación en la niñez, en una aproximación que se realiza desde un enfoque cualitativo y etnográfico. En los hallazgos, sobresale cómo las niñas y niños se muestran preparados para ejercer su derecho a la participación como aspecto de sus vidas que se haría posible dentro del marco normativo existente, pero que aún no es asumido en prácticas sociales que los incluyan.

Superconducting properties of Zr1+xNi2-xGa and Zr1-xNi2+xGa Heusler compounds

Directory of Open Access Journals (Sweden)

Saad Alzahrani

2017-05-01

Full Text Available The superconducting properties of a series of Zr1+xNi2-xGa and Zr1-xNi2+xGa compounds have been investigated by x-ray diffraction, electrical resistivity, dc magnetization, and ac susceptibility measurements. While the parent compound, ZrNi2Ga, exhibited the cubic L21 Heusler structure, multiple non-cubic structures formed in the Zr and Ni rich doped materials. For x ≤ 0.3, all Zr1-xNi2+xGa compounds demonstrated superconducting behavior, but no superconductivity was observed in the Zr1+xNi2-xGa alloys for x > 0.2. The magnetization data revealed that all materials in both Zr1+xNi2-xGa and Zr1-xNi2+xGa series exhibited type-II superconductivity. With increasing doping concentration x, the paramagnetic ordering were enhanced in both systems while the superconducting properties were found to weaken. The observations are discussed considering the structural disorders in the systems.

Low-temperature synthesis of the infinite-layer compound LaNiO2 by soft-chemical techniques

International Nuclear Information System (INIS)

Takamatsu, Tomohisa; Kato, Masatsune; Noji, Takashi; Koike, Yoji

2010-01-01

Bulk samples of LaNiO 2 with the so-called infinite-layer structure have successfully been synthesized. First, polycrystalline samples of LaNiO 3 with the perovskite structure were prepared using molten KOH at a temperature of 400-450degC. Then, they were finely ground with a double stoichiometric excess of reductant CaH 2 and sealed in an evacuated Pyrex tube. The sealed ampoule was then heated at 300degC for 24 h. Powder X-ray diffraction analysis has revealed that the product obtained after removing the residual CaH 2 and the byproduct CaO is of almost single phase with tetragonal symmetry, indicating the formation of the infinite-layer compound LaNiO 2 . (author)

Communication: Surface-to-bulk diffusion of isolated versus interacting C atoms in Ni(111) and Cu(111) substrates: A first principle investigation

Energy Technology Data Exchange (ETDEWEB)

Harpale, Abhilash; Panesi, Marco; Chew, Huck Beng, E-mail: hbchew@illinois.edu [Department of Aerospace Engineering, University of Illinois at Urbana-Champaign, Urbana, Illinois 61801 (United States)

2015-02-14

Using first principle calculations, we study the surface-to-bulk diffusion of C atoms in Ni(111) and Cu(111) substrates, and compare the barrier energies associated with the diffusion of an isolated C atom versus multiple interacting C atoms. We find that the preferential Ni-C bonding over C–C bonding induces a repulsive interaction between C atoms located at diagonal octahedral voids in Ni substrates. This C–C interaction accelerates C atom diffusion in Ni with a reduced barrier energy of ∼1 eV, compared to ∼1.4-1.6 eV for the diffusion of isolated C atoms. The diffusion barrier energy of isolated C atoms in Cu is lower than in Ni. However, bulk diffusion of interacting C atoms in Cu is not possible due to the preferential C–C bonding over C–Cu bonding, which results in C–C dimer pair formation near the surface. The dramatically different C–C interaction effects within the different substrates explain the contrasting growth mechanisms of graphene on Ni(111) and Cu(111) during chemical vapor deposition.

Comparison of stability of WSiX/SiC and Ni/SiC Schottky rectifiers to high dose gamma-ray irradiation

International Nuclear Information System (INIS)

Kim, Jihyun; Ren, F.; Chung, G.Y.; MacMillan, M.F.; Baca, A.G.; Briggs, R.D.; Schoenfeld, D.; Pearton, S.J.

2004-01-01

SiC Schottky rectifiers with moderate breakdown voltages of ∼450 V and with either WSi X or Ni rectifying contacts were irradiated with Co-60 γ-rays to doses up to ∼315 Mrad. The Ni/SiC rectifiers show severe reaction of the contact after irradiation at the highest dose, badly degrading the forward current characteristics and increasing the on-state resistance by up to a factor of 6 after irradiation. By sharp contrast, the WSi X /SiC devices show little deterioration of the contact with the same conditions and changes in on-state resistance of X contacts appear promising for applications requiring improved contact stability

Las prácticas educativas familiares como facilitadoras del proceso de desarrollo en el niño y niña

OpenAIRE

Henao López, Gloria Cecilia; Ramírez Palacio, Carlota; Ramírez Nieto, Luz Angela

2007-01-01

Para facilitar una mejor comprensión sobre las prácticas educativas familiares como facilitadoras del proceso del desarrollo en la niñez, se aborda el siguiente artículo a partir de dos bloques temáticos, integrados en forma dinámica, siendo impulsadoras en el niño y la niña de nuevas zonas de desarrollo. En primer lugar, se aborda la teoría de Vigotsky sobre la ley de la doble formación, la zona de desarrollo próximo y la teoría de la participación guiada de Bárbara Rogoff, dos teorías inscr...

Study of hyperfine interactions in intermetallic compounds Gd(Ni,Pd,Cu)In, Tb(Ni,Pd)In, Dy(Ni,Pd)In and Ho(Ni,Pd)In

International Nuclear Information System (INIS)

Lapolli, Andre Luis

2006-01-01

Systematic behavior of magnetic hyperfine field (B hf ) in the intermetallic compounds Gd(Ni,Pd,Cu)In Tb(Ni,Pd)In, Dy(Ni,Pd)In and Ho(Ni,Pd)In was studied by Perturbed Gamma-Gamma Angular Correlation spectroscopy. The measurements of B hf were carried out at the rare earth atom and in sites using the nuclear probes 140 Ce and 11 '1Cd respectively. The variation of hyperfine field with temperature, in most cases, follows the Brillouin function predicted from the molecular field theory. The hyperfine field values at rare earth atom sites obtained from 140 Ce probe as well as at in sites obtained from 111 Cd probe for each series of compounds were extrapolated to zero Kelvin B hf (T=0) from these curves. These values were compared with the values of the literature for other compounds containing the same rare earth element and all of them show a linear relationship with the ordering temperature. This indicates that the main contribution to B hf comes from the conduction electron polarization (CEP) through Fermi contact interaction and the principal mechanism of magnetic interaction in these compounds can be described by the RKKY type interaction. The values of B hf (T=0) for each family of intermetallic compounds RNiIn and RPdIn when plotted as a function of 4f spin projection of rare earth element also shows a linear relationship. Exceptions are the results for the compounds RNiIn obtained with 111 Cd probe where a small deviation from linearity is observed. The results of the measurements carried out with the 111 Cd probe were also analyzed to obtain the hyperfine parameters of the quadrupole interaction as a function of temperature for RPdln and GdNiIn compounds. The results show that for the compound GdPdIn there might be some Gd-In disorder at high temperature. (author)

X-ray diffraction study of chalcopyrite CuFeS2, pentlandite (Fe,Ni)9S8 and Pyrrhotite Fe1-xS obtained from Cu-Ni orebodies

International Nuclear Information System (INIS)

Nkoma, J.S.; Ekosse, G.

1998-05-01

The X-ray Diffraction (XRD) technique is applied to study five samples of Cu-Ni orebodies, and it is shown that they contain chalcopyrite CuFeS 2 as the source of Cu, pentlandite (Fe,Ni) 9 S 8 as the source of Ni and pyrrhotite Fe 1-x S as a dominant compound. There are also other less dominant compounds such as bunsenite NiO, chalcocite Cu 2 S, penrosite (Ni, Cu)Se 2 and magnetite Fe 3 O 4 . Using the obtained XRD data, we obtain the lattice parameters for tetragonal chalcopyrite as a=b=5.3069A and c=10.3836A, cubic pentlandite as a=b=c=10.0487A, and hexagonal pyrrhotite as a=b=6.8820A and c=22.8037A. (author)

Catalytic reforming of toluene as tar model compound: effect of Ce and Ce-Mg promoter using Ni/olivine catalyst.

Science.gov (United States)

Zhang, Ruiqin; Wang, Huajian; Hou, Xiaoxue

2014-02-01

Tar produced by biomass gasification as a route of renewable energy must be removed before the gas can be used. This study was undertaken using toluene as a model tar compound for evaluating its steam reforming conversion with three Ni-based catalysts, Ni/olivine, Ni-Ce/olivine and Ni-Ce-Mg/olivine. Effects of Ce and Mg promoters on the reaction activity and coke deposition were studied. Overall the performance of Ce and Mg promoted Ni/olivine catalysts is better than that of only Ce promoter and Ni/olivine alone. The experimental results indicate that Ni-Ce-Mg/olivine catalysts could improve the resistance to carbon deposition, enhance energy gases yield and resist 10ppm H2S poison at 100mLmin(-1) for up to 400min. Furthermore, the activity of catalysts was related to the steam/carbon (S/C) ratios; at S/C ratio=5, T=790°C, space velocity=782h(-1) and t=2h, the Ni-Ce-Mg/olivine system yielded 89% toluene conversion, 5.6Lh(-1) product gas rate, 62.6mol% H2 content and 10% (mol useful gas mol(-1) toluene) energy yield. Moreover, at low S/C ratio, it had higher reaction activity and better ability to prevent coking. There is a small amount of carbon deposition in the form of amorphous carbon after 7h. Various characterization techniques such as XRD, FTIR and thermogravimetric were performed to investigate the coke deposition of Ni/olivine, Ni-Ce/olivine and Ni-Ce-Mg/olivine. It is suggested that 3% Ni-1% Ce-1% Mg/olivine was the most promising catalyst due to its minimum coke amount and the lower activation energy of coke burning. Copyright © 2014. Published by Elsevier Ltd.

Development of Cr3C2-25(Ni20Cr) nanostructured coatings

International Nuclear Information System (INIS)

Cunha, Cecilio Alvares da

2012-01-01

This study is divided in two parts. The first part is about the preparation of nanostructured Cr 3 C 2 -25(Ni20Cr) powders by high energy milling followed by characterization of the milled and the as received powder. Analyses of some of the data obtained were done using a theoretical approach. The second part of this study is about the preparation and characterization of coatings prepared with the nanostructured as well as the as received Cr 3 C 2 -25(Ni20Cr) powders. The high temperature erosion-oxidation (E-O) behavior of the coatings prepared with the two types of powders has been compared based on a technological approach. The average crystallite size of the Cr 3 C 2 -25(Ni20Cr) powder decreased rapidly from 145 nm to 50 nm in the initial stages of milling and thereafter decreased slowly to a steady state value of around 10 nm with further increase in milling time. This steady state corresponds to the beginning of a dynamic recovery process. The maximum lattice strain (ε = 1,17%) was observed in powders milled for 16 hours, and this powders critical crystallite size was 28 nm. In contrast, the lattice parameter attained a minimum for powders milled for 16 hours. Upon reaching the critical crystallite size, the dislocation density attained a steady state regime and all plastic deformation introduced in the material there after was in the form of events occurring at the grain boundaries, due mainly to grain boundary sliding. The deformation energy stored in the crystal lattice of the Cr 3 C 2 -25(Ni20Cr) powders milled for different times was determined from enthalpy variation measurements. These results indicated that the maximum enthalpy variation (δH = 722 mcal) also occurred for powders milled for 16 hours. In a similar manner, the maximum specific heat variation (δC p = 0,278 cal/gK) occurred for powders milled for 16 hours. The following mechanical properties of Cr 3 C 2 -25(Ni20Cr) coatings prepared using the HVOF thermal spray process were determined

Sintering behaviour and mechanical properties of Cr3C2–NiCr ...

Indian Academy of Sciences (India)

fracture toughness. Keywords. Cermet; Cr3C2–NiCr; sintering; mechanical properties. ... et al investigated the mechanical properties of VC, Cr3C2 and NbC doped ..... Huang S G, Li L, Van der Biest O and Vleugels J 2008 J. Alloys. Compds.

Magnetic properties of intermetallic compounds La(Ni,Co,Cu)3

Science.gov (United States)

Tazuke, Y.; Tanikawa, H.; Okano, A.; Miyaji, T.

2006-09-01

LaNi3 exhibited a metallic antiferromagnetic property with T N = 30 K. La(Ni1-x Cox )3 with x = 0.01, 0.03 and 0.05 exhibited ferromagnetic properties, T C increasing linearly with increasing x . La(Ni1-2z Coz Cuz )3 with z = 0.015 exhibited a ferromagnetic property with a small T C. A La(Ni1-y Cuy )3 sample with y = 0.01 exhibited a Pauli-paramagnetic property; those with y = 0.02, 0.03 and 0.04 exhibited gradual metamagnetic behavior and that with y = 0.05 exhibited a ferromagnetic property. The gradual metamagnetic M -H variations are numerically simulated by using Landau-type free energies. The results suggest that the gradual metamagnetic behavior occurs from an antiferromagnetic state to a ferromagnetic one.

Effect of Mo and C additions on magnetic properties of TiC–TiN–Ni cermets

International Nuclear Information System (INIS)

Zhang, Man; Yang, Qingqing; Xiong, Weihao; Zheng, Liyun; Huang, Bin; Chen, Shan; Yao, Zhenhua

2015-01-01

The effect of 2–8 mol.% Mo and 4 mol.% C additions on magnetic properties of TiC–10TiN–30Ni (mol.%) cermet was investigated. Saturation magnetization M_s, remanence M_r and Curie temperature T_c of as-sintered cermets (1420 °C, 1 h) decreased with increasing Mo. This was mainly attributed to that the total content of non-magnetic alloying elements Mo and Ti in Ni-based binder phase increased with increasing Mo in cermets, leading to the weakening of magnetic exchange interaction among Ni atoms in binder phase. The further addition of 4 mol.% C inversely increased M_s, M_r and T_c of cermets, which was mainly attributed to that it decreased the total content of Mo and Ti in binder phase, leading to the strengthening of magnetic exchange interaction among Ni atoms in binder phase. T_c of cermets without C addition was about 250 K at 6 mol.% Mo and 115 K at 8 mol.% Mo, respectively, and that of cermets with 4 mol.% C addition was about 194 K at 8 mol.% Mo. - Highlights: • M_s, M_r and T_c of TiC–10TiN–30Ni–xMo cermets decreased with the increase of Mo content, x. • Further addition of 4 mol.% C inversely increased M_s, M_r and T_c of cermets at the same Mo content. • T_c of cermets without C addition was about 250 K at x = 6 and 115 K at x = 8, respectively. • T_c of cermets with 4 mol.% C addition was about 194 K at x = 8.

Fabrication and thermoelectric properties of fine-grained TiNiSn compounds

International Nuclear Information System (INIS)

Zou Minmin; Li Jingfeng; Du Bing; Liu Dawei; Kita, Takuji

2009-01-01

Nearly single-phased TiNiSn half-Heusler compound thermoelectric materials were synthesized by combining mechanical alloying (MA) and spark plasma sintering (SPS) in order to reduce its thermal conductivity by refining the grain sizes. Although TiNiSn compound powders were not synthesized directly via MA, dense bulk samples of TiNiSn compound were obtained by the subsequent SPS treatment. It was found that an excessive Ti addition relative to the TiNiSn stoichiometry is effective in increasing the phase purity of TiNiSn half-Heusler phase in the bulk samples, by compensating for the Ti loss caused by the oxidation of Ti powders and MA processing. The maximum power factor value obtained in the Ti-compensated sample is 1720 μW m -1 K -2 at 685 K. A relatively high ZT value of 0.32 is achieved at 785 K for the present undoped TiNiSn compound polycrystals. - Graphical abstract: Nearly single-phased TiNiSn-based half-Heusler compound polycrystalline materials with fine grains were fabricated by combining mechanical alloying (MA) and spark plasma sintering (SPS). A high ZT value for undoped TiNiSn was obtained because of the reduced thermal conductivity.

Experimental investigation of phase equilibria in the Zr-Cu-Ni ternary system

Energy Technology Data Exchange (ETDEWEB)

Yang, Mujin; Wang, Cuiping; Yang, Shuiyuan; Shi, Zhan; Han, Jiajia; Liu, Xingjun [Xiamen Univ. (China). College of Materials and Fujian Provincial Key Lab. of Materials Genome

2017-08-15

The phase equilibria in the Zr-Cu-Ni ternary system are investigated combined with X-ray diffraction, electron probe micro-analysis and differential scanning calorimetry. Two isothermal sections of the Zr-Cu-Ni ternary system at 1 000 C and 1 100 C are experimentally established. Most of the binary intermetallic compounds, e.g. Zr{sub 7}Ni{sub 10}, ZrNi, ZrNi{sub 5}, Zr{sub 14}Cu{sub 51}, and Zr{sub 2}Cu{sub 9}, show a remarkable ternary solubility. A new ternary compound named τ{sub 3} (Zr{sub 31.1-30.7} . Cu{sub 28.5-40.3}Ni{sub 40.4-29.0}) is detected at 1 000 C and dissolved at 1 020 C because the nearby large liquid phase field further expands. The newly determined phase equilibria will provide important information for both thermodynamic assessment and alloy design of Zr-based metallic glass.

OXIDATIVE-REFORMING OF METHANE AND PARTIAL OXIDATION OF METHANE REACTIONS OVER NiO/PrO2/ZrO2 CATALYSTS: EFFECT OF NICKEL CONTENT

Directory of Open Access Journals (Sweden)

Y. J. O. Asencios

Full Text Available Abstract In this work the behavior of NiO-PrO2-ZrO2 catalysts containing various nickel loadings was evaluated in the partial oxidation of methane and oxidative-reforming reactions of methane. The catalysts were characterized by X-Ray Diffraction Analysis (in situ-XRD, Temperature Programmed Reduction (H2-TPR, Scanning Electron Microscopy (SEM/EDX and Adsorption-Desorption of nitrogen (BET area. The reactions were carried out at 750 °C and 1 atm for 5 hours. The catalysts were studied with different nickel content: 0, 5, 10 and 15% (related to total weight of catalyst, wt%. In both reactions, the catalyst containing the mixture of the three oxides (NiO/PrO2/ZrO2 with 15% nickel (15NiPrZr catalyst showed the best activity for the conversion of the reactants into Syngas and showed high selectivity for H2 and CO. The results suggest that the promoter PrO2 and the Niº centers are in a good proportion in the catalyst with 15% Ni. Our results showed that low nickel concentrations in the catalyst led to high metallic dispersion; however, very low nickel concentrations did not favor the methane transformation into Syngas. The catalyst containing only NiO/ZrO2 in the mixture was not sufficient for the catalysis. The presence of the promoter PrO2 was very important for the catalysis of the POM.

Development of a NiO target for the production of {sup 11}C at ISAC/TRIUMF

Energy Technology Data Exchange (ETDEWEB)

Bricault, Pierre G.; Ames, Friedhelm; Dombsky, Marik; Kunz, Peter; Lassen, Jens; Mjøs, Anders; Wong, John

2016-01-01

High intensity {sup 11}C beams are necessary for the investigation of the formation of {sup 12}C via the nuclear reaction {sup 11}C(p, γ){sup 12}N → {sup 12}C + e{sup +} + ν. The production of intense carbon beams on-line is quite challenging due to the thermodynamic properties and chemical reactivity of carbon at high temperatures. A previous attempt, using a medical isotope cyclotron production method in batch mode, was not conclusive. The intensity obtained was at least one order of magnitude too low for a direct proton capture experiment using the DRAGON facility at ISAC/TRIUMF. Producing a {sup 11}C beams using the ISOL method requires a target capable of efficiently releasing the carbon isotopes. NiO has been selected as a target material because most of the nickel carbides are not stable at high temperature. The development of carbon beams using a composite NiO/Ni target on-line is described.

Synthesis and hydrogen storage of La23Nd7.8Ti1.1Ni33.9Co32.9Al0.65 alloys

Directory of Open Access Journals (Sweden)

Priyanka Meena

2018-04-01

Full Text Available The present work investigates structural and hydrogen storage properties of first time synthesized La23Nd7.8Ti1.1Ni33.9Co32.9Al0.65 alloy by arc melting process and ball milled to get it in nano structure form. XRD analysis of as-prepared alloy showed single phased hexagonal LaNi5-type structure with 52 nm average particle size, which reduces to about 31 nm after hydrogenations. Morphological studies by SEM were undertaken to investigate the effect of hydrogenation of nanostructured alloy. EDX analysis confirmed elemental composition of the as-prepared alloy. Activation energy for hydrogen desorption was studied using TGA analysis and found to be −76.86 kJ/mol. Hydrogenation/dehydrogenation reactions and absorption kinetics were measured at temperature 100 °C. The equilibrium plateau pressure was determined to be 2 bar at 100 °C giving hydrogen storage capacity of about 2.1 wt%. Keywords: Hydrogen storage, La23Nd7.8Ti1.1Ni33.9Co32.9Al0.65 alloy, SEM, EDS, TGA, Hydrogenation/dehydrogenation

Facile Synthesis of A 3D Flower-Like Mesoporous Ni@C Composite Material for High-Energy Aqueous Asymmetric Supercapacitors.

Science.gov (United States)

Liu, Song; An, Cuihua; Zang, Lei; Chang, Xiaoya; Guo, Huinan; Jiao, Lifang; Wang, Yijing

2018-04-16

A 3D flower-like mesoporous Ni@C composite material has been synthesized by using a facile and economical one-pot hydrothermal method. This unique 3D flower-like Ni@C composite, which exhibited a high surface area (522.4 m 2  g -1 ), consisted of highly dispersed Ni nanoparticles on mesoporous carbon flakes. The effect of calcination temperature on the electrochemical performance of the Ni@C composite was systematically investigated. The optimized material (Ni@C 700) displayed high specific capacity (1306 F g -1 at 2 A g -1 ) and excellent cycling performance (96.7 % retention after 5000 cycles). Furthermore, an asymmetric supercapacitor (ASC) that contained Ni@C 700 as cathode and mesoporous carbon (MC) as anode demonstrated high energy density (60.4 W h kg -1 at a power density of 750 W kg -1 ). © 2018 Wiley-VCH Verlag GmbH & Co. KGaA, Weinheim.

Experimental investigation of phase equilibria in the Ni-Nb-V ternary system

Energy Technology Data Exchange (ETDEWEB)

Liu, Xingjun; Yang, Shuiyuan; Wang, Cuiping [Xiamen Univ. (China). Dept. of Materials Science and Engineering; Xiamen Univ. (China). Fujian Provincial Key Lab. of Materials Genome; Zhang, Xianjie; Jiang, Hengxing; Shi, Zhan [Xiamen Univ. (China). Dept. of Materials Science and Engineering

2017-09-15

The phase equilibria of the Ni-Nb-V ternary system at 1000 C and 1200 C were established using electron probe microanalysis, X-ray diffraction and differential scanning calorimetry. The results of the investigation revealed that: (1) The Nb solubility in (Ni) and σ{sup '} phases was less than 10 at.%; (2) A ternary compound τ (NiNbV) was confirmed, in which V had a large solubility; (3) A new liquid region was evident at 1200 C, but was absent at 1000 C; (4) The lattice constants of Ni{sub 3}Nb and Ni{sub 6}Nb{sub 7} phase decreased with increase in V content in the Ni{sub 3}Nb and Ni{sub 6}Nb{sub 7}. The phase equilibria of the Ni-Nb-V ternary system will contribute to its thermodynamic assessment.

Erosion-oxidation behavior of thermal sprayed Ni20Cr alloy and WC and Cr3C2 cermet coatings

Directory of Open Access Journals (Sweden)

Clarice Terui Kunioshi

2005-06-01

Full Text Available An apparatus to conduct high temperature erosion-oxidation studies up to 850 °C and with particle impact velocities up to 15 m.s-1 was designed and constructed in the Corrosion Laboratories of IPEN. The erosion-oxidation behavior of high velocity oxy fuel (HVOF sprayed alloy and cermet coatings of Ni20Cr, WC 20Cr7Ni and Cr3C2 Ni20Cr on a steel substrate has been studied. Details of this apparatus and the erosion-oxidation behavior of these coatings are presented and discussed. The erosion-oxidation behavior of HVOF coated Cr3C2 25(Ni20Cr was better than that of WC 20Cr7Ni, and the erosion-oxidation regimes have been identified for these coatings at particle impact velocity of 3.5 m.s-1, impact angle of 90° and temperatures in the range 500 to 850 °C.

Electronic structure of Ni-- and Ni2--ethylene cluster complexes

International Nuclear Information System (INIS)

Basch, H.; Newton, M.D.; Moskowitz, J.W.

1978-01-01

The electronic structure of metal cluster--ethylene complexes has been investigated by carrying out ab initio bonding pair-correlated, self-consistent field, and configuration interaction (CI) calculations on the NiC 2 H 4 and Ni 2 C 2 H 4 species. The π-NiC 2 H 4 and π-Ni 2 C 2 H 4 cluster complexes are found to be bound, the former only with CI, while disigma-Ni 2 C 2 H 4 has only a repulsive Ni 2 --C 2 H 4 ground state potential curve. The bonding in the π-type cluster complexes can be described as follows: The metal atom configuration is 3d 9 4s 1 with the 4s hybridized (by the metal 4p) away from the ethylene molecule, thereby allowing the π orbital to form a dative sigma bond with the metal atom. The bonding interaction is promoted by the presence of a second nickel atom behind the first one, leading to a 4s orbital electron deficiency of the bonded nickel atom and thus making this nickel atom a better electron acceptor. Back donation from the occupied metal 3d into the ethylene π* molecular orbital also takes place to some extent, and thus both features of the classical Dewar--Chatt--Duncanson model are observed. The π-Ni 2 C 2 H 4 species is analyzed in terms of the addition of a bare nickel atom to a π-NiC 2 H 4 cluster complex, with concomitant stabilization of the orbitals of the bonded nickel atom. A study of the excited electronic states of π-NiC 2 H 4 shows that low-lying 4s→π* and 3d→π* (M→L) charge transfer transitions are predicted. The former is not observed experimentally, probably due to the diffuse nature of the 4s orbital. The relationship between small cluster--ethylene complex systems and ethylene chemisorption on a nickel metal surface is discussed

STUDY OF COATINGS OBTAINED FROM ALLOY Fe-Mn-C-B-Si-Ni-Cr

Directory of Open Access Journals (Sweden)

Mychajło Paszeczko

2016-09-01

Full Text Available Tribological behaviour of coatings obtained from eutectic alloy Fe-Mn-C-B-Si-Ni-Cr was studied. The coatings were obtained by the method of gas metal arc welding (GMA with use of powder wire. GMA welding method is widely used for the regeneration of machine parts. Eutectic Fe-Mn-C-B-Si-Ni-Cr alloys can be used to obtain high quality coatings resistant to wear and corrosion. Pin-on-disk dry sliding wear tests at sliding speeds 0.4 m/s and under load 10 MPa were conducted for pin specimens. During friction a typical tribological behavior was observed. The mechanism of wear was mechanical-chemical.

Phase stability, crystal structure and magnetism in (U1-xNbx)2 Ni21B6 and (UyNb1-y)3Ni20B6

Science.gov (United States)

Provino, Alessia; Bhattacharya, Amitava; Dhar, Sudesh K.; Pani, Marcella; Gatti, Flavio; Paudyal, Durga; Manfrinetti, Pietro

Ternary phases with composition T2M21X6 and T3M20X6 (T = transition metal; M = 3 d metal; X = B, C, P) are reported to crystallize with the W2Cr21C6-type and Mg3Ni20B6-type, respectively (ternary ordered derivatives of the cubic Cr23C6-type, cF116). They attract interest due to their refractory, mechanical, and peculiar magnetic properties. Literature data on these compounds only concern apparently stoichiometric 2:21:6 and 3:20:6 phases. Often only nominal composition has been reported, with few structural refinements and no measurements of physical properties. Lack of detailed stoichiometry and crystallographic data does not allow sufficient understanding of the crystal chemistry and properties of these compounds. We studied stability, crystal structure and magnetism of (U1-xNbx)2 Ni21B6 and (UyNb1-y)3Ni20B6; stable phases are U2Ni21B6 and Nb3Ni20B6, as also confirmed by theoretical calculations. The two pristine compounds solubilize Nb and U, respectively, up to a given extent. The substitution of U by Nb leads to a structural change from the W2Cr21C6- to the Mg3Ni20B6-type. While U2Ni21B6 is a Pauli paramagnet (itinerant non-magnetic state of U-5 f electrons), in agreement with literature, magnetization data for (UyNb1-y)3 Ni20B6 show itinerant ferromagnetism with TC >300 K.

Effect of Mo and C additions on magnetic properties of TiC–TiN–Ni cermets

Energy Technology Data Exchange (ETDEWEB)

Zhang, Man [State Key Laboratory of Material Processing and Die & Mould Technology, Huazhong University of Science and Technology, Wuhan 430074 (China); Yang, Qingqing, E-mail: yqqah@sina.com [State Key Laboratory of Material Processing and Die & Mould Technology, Huazhong University of Science and Technology, Wuhan 430074 (China); Xiong, Weihao [State Key Laboratory of Material Processing and Die & Mould Technology, Huazhong University of Science and Technology, Wuhan 430074 (China); Zheng, Liyun [School of Equipment Manufacture, Hebei University of Engineering, Handan 056038 (China); Huang, Bin; Chen, Shan; Yao, Zhenhua [State Key Laboratory of Material Processing and Die & Mould Technology, Huazhong University of Science and Technology, Wuhan 430074 (China)

2015-11-25

The effect of 2–8 mol.% Mo and 4 mol.% C additions on magnetic properties of TiC–10TiN–30Ni (mol.%) cermet was investigated. Saturation magnetization M{sub s}, remanence M{sub r} and Curie temperature T{sub c} of as-sintered cermets (1420 °C, 1 h) decreased with increasing Mo. This was mainly attributed to that the total content of non-magnetic alloying elements Mo and Ti in Ni-based binder phase increased with increasing Mo in cermets, leading to the weakening of magnetic exchange interaction among Ni atoms in binder phase. The further addition of 4 mol.% C inversely increased M{sub s}, M{sub r} and T{sub c} of cermets, which was mainly attributed to that it decreased the total content of Mo and Ti in binder phase, leading to the strengthening of magnetic exchange interaction among Ni atoms in binder phase. T{sub c} of cermets without C addition was about 250 K at 6 mol.% Mo and 115 K at 8 mol.% Mo, respectively, and that of cermets with 4 mol.% C addition was about 194 K at 8 mol.% Mo. - Highlights: • M{sub s}, M{sub r} and T{sub c} of TiC–10TiN–30Ni–xMo cermets decreased with the increase of Mo content, x. • Further addition of 4 mol.% C inversely increased M{sub s}, M{sub r} and T{sub c} of cermets at the same Mo content. • T{sub c} of cermets without C addition was about 250 K at x = 6 and 115 K at x = 8, respectively. • T{sub c} of cermets with 4 mol.% C addition was about 194 K at x = 8.

Crystalline electric fields and magnetic properties of single-crystalline RNiC2 compounds R=Ho, Er and Tm

International Nuclear Information System (INIS)

Koshikawa, Y.; Onodera, H.; Kosaka, M.; Yamauchi, H.; Ohashi, M.; Yamaguchi, Y.

1997-01-01

Magnetometric investigations were performed on single-crystalline HoNiC 2 , ErNiC 2 and TmNiC 2 compounds. Susceptibility of HoNiC 2 shows no anomaly around T N , but a clear cusp appears at T t =2.9 K. Magnetization curves reveal that the anisotropy is relatively weak and that the Ho moments align not along any crystallographic axis. In addition to T N =8.5 K of ErNiC 2 , a new order-order transition at T t =3.6 K has been found. Although the Er moments align along the a-axis between T t and T N , it seems certain that the small moment-components along the b- and c-axes come into existence below T t . TmNiC 2 with T N =5.5 K has a strong uniaxial anisotropy along the a-axis. These results are discussed on the basis of competitions between the magnetic interactions and the crystal field effect which changes anomalously by the replacement of rare earth element. It has been found that the drastic change of crystal field occurs between HoNiC 2 and ErNiC 2 without any corresponding structural change. (orig.)

Effects of Ni{sub 3}Sn{sub 4} and (Cu,Ni){sub 6}Sn{sub 5} intermetallic layers on cross-interaction between Pd and Ni in solder joints

Energy Technology Data Exchange (ETDEWEB)

Baek, Yong-Ho [Department of Materials Science and Engineering, Korea University, Seoul 136-713 (Korea, Republic of); Division of Advanced Circuit Interconnect, Samsung Electro-Mechanics Co., Ltd., Suwon 443-743 (Korea, Republic of); Chung, Bo-Mook [Department of Materials Science and Engineering, Korea University, Seoul 136-713 (Korea, Republic of); Department of Research and Development, KPM TECH, Ansan 425-090 (Korea, Republic of); Choi, Young-Sik [Division of Advanced Circuit Interconnect, Samsung Electro-Mechanics Co., Ltd., Suwon 443-743 (Korea, Republic of); Choi, Jaeho [Department of Advanced Metal and Materials Engineering, Gangneung-Wonju National University, Gangneung 210-702 (Korea, Republic of); Huh, Joo-Youl, E-mail: jyhuh@korea.ac.kr [Department of Materials Science and Engineering, Korea University, Seoul 136-713 (Korea, Republic of)

2013-12-05

Highlights: •Ni{sub 3}Sn{sub 4} acts as a source of Ni atoms, leading to a strong cross-interaction with Pd. •(Cu,Ni){sub 6}Sn{sub 5} is an effective Ni diffusion barrier, inhibiting Pd resettlement. •Dissolution kinetics of (Pd,Ni)Sn{sub 4} was interpreted based on the Sn–Ni–Pd isotherm. •Cu addition to solder alleviates the (Pd,Ni)Sn{sub 4}-related risk of reliability deterioration. -- Abstract: We examined the effects of layers of intermetallic compound (IMC) Ni{sub 3}Sn{sub 4} and (Cu,Ni){sub 6}Sn{sub 5} formed at the solder/Ni interface, on the cross-interactions between Pd and Ni during solid-state aging and reflow soldering. Two types of diffusion couples, Pd/Sn/Ni and Pd/Sn–Cu/Ni, were aged at 150 °C to study the solid-state interactions. In contrast to the Pd/Sn/Ni couples in which a Ni{sub 3}Sn{sub 4} layer formed at the Ni interface, the Pd/Sn–Cu/Ni couple where a (Cu,Ni){sub 6}Sn{sub 5} layer formed at the Ni interface exhibited no significant interaction between Pd and Ni. The (Cu,Ni){sub 6}Sn{sub 5} layer acted as an effective barrier against Ni diffusion and thus inhibited the resettlement of (Pd,Ni)Sn{sub 4} onto the Ni interface. For the interaction during reflow, Sn–3.5Ag and Sn–3.0Ag–0.5Cu solder balls were isothermally reflowed on an electroless Ni(P)/electroless Pd/immersion Au (ENEPIG) surface finish at 250 °C, and the dissolution kinetics of the (Pd,Ni)Sn{sub 4} particles converted from the 0.2-μm-thick Pd-finish layer were examined. The spalled (Pd,Ni)Sn{sub 4} particles very quickly dissolved into the molten solder when the IMC layer formed on the Ni substrate was (Cu,Ni){sub 6}Sn{sub 5} rather than Ni{sub 3}Sn{sub 4}. The dependence of the dissolution kinetics of the spalled (Pd,Ni)Sn{sub 4} particles on the IMC layers was rationalized on the basis of a Sn–Ni–Pd isotherm at 250 °C. The present study suggests that the formation of a dense (Cu,Ni){sub 6}Sn{sub 5} layer at the solder/Ni interface can effectively

Physico-Chemical and Electrochemical Properties of Nanoparticulate NiO/C Composites for High Performance Lithium and Sodium Ion Battery Anodes

Directory of Open Access Journals (Sweden)

Amaia Iturrondobeitia

2017-12-01

Full Text Available Nanoparticulate NiO and NiO/C composites with different carbon proportions have been prepared for anode application in lithium and sodium ion batteries. Structural characterization demonstrated the presence of metallic Ni in the composites. Morphological study revealed that the NiO and Ni nanoparticles were well dispersed in the matrix of amorphous carbon. The electrochemical study showed that the lithium ion batteries (LIBs, containing composites with carbon, have promising electrochemical performances, delivering specific discharge capacities of 550 mAh/g after operating for 100 cycles at 1C. These excellent results could be explained by the homogeneity of particle size and structure, as well as the uniform distribution of NiO/Ni nanoparticles in the in situ generated amorphous carbon matrix. On the other hand, the sodium ion battery (NIB with the NiO/C composite revealed a poor cycling stability. Post-mortem analyses revealed that this fact could be ascribed to the absence of a stable Solid Electrolyte Interface (SEI or passivation layer upon cycling.

Synthesis of NiPS3 and CoPS and its hydrogen storage capacity

International Nuclear Information System (INIS)

Ismail, N.; Madian, M.; El-Meligi, A.A.

2014-01-01

Highlights: • Preparation of NiPS 3 and CoPS using solid state reaction. • Characterization of compounds using XRD, TEM, SEM and IR. • Measuring the compounds thermal stability. • Estimation of the hydrogen storage capacity. -- Abstract: Prepared CoPS and NiPS 3 are studied as new materials for hydrogen energy storage. Single phase of CoPS and NiPS 3 were grown separately in evacuated silicatube via solid state reaction at 650 °C with controlled heating rate 1 °C/min. X-ray diffraction patterns confirm the formation of the desired compounds. Both CoPS and NiPS 3 exhibited high thermal stability up to 700 °C and 630 °C, respectively. The morphology of the prepared samples was investigated using scanning electron microscopy and folded sheets appeared in the transmission electron microscopy. The samples were exposed to 20 bar applied hydrogen pressure at 80 K. Both compounds appear to have feasible hydrogen storage capacity. CoPS was capable to adsorb 1.7 wt% while NiPS 3 storage capacity reached 1.2 wt%

Microstructure of a Ni Matrix Composite Coating Reinforced by In-situ TiC Particles Using Plasma Cladding

Institute of Scientific and Technical Information of China (English)

WUYu-ping; WANGZe-hua; LINPing-hua

2004-01-01

Plasma cladding process was used to prepare the TiC/Ni composite coating on the mild steel substrates. The TiC particles were synthesized in-situ. Microstructure and properties of the coating were investigated by optical microscopy, X-Ray diffraction, SEM, TEM and microhardness tester. The results show that the interface between the coating and the substrate is metallurgically bonded. The coating was uniform and almost defect-free when [Ti+C] varied from 10% to 20% after ball milling. The microstructure of the coating is mainly composed of γ-Ni dendrite, interdendritic eutectic (γ-Ni austenite, M23C6 and CrB) and TiC particles. Most of the TiC particles are spherical and a small fraction is blocky in size of 1-2μm. The TiC particles are smaller at the bottom than near the top of the coating. The coating has a gradient microstructure and a highest hardness of 1000Hv0.1.

Anomalous magnetoresistance in antiferromagnetic polycrystalline materials R2Ni3Si5 (R=rare earth)

International Nuclear Information System (INIS)

Mazumdar, C.; Nigam, A.K.; Nagarajan, R.; Gupta, L.C.; Chandra, G.; Padalia, B.D.; Godart, C.; Vijayaraghaven, R.

1997-01-01

Magnetoresistance (MR) studies on polycrystalline R 2 Ni 3 Si 5 , (R=Y, rare earth) which order antiferromagnetically at low temperatures, are reported here. MR of the Nd, Sm, and Tb members of the series exhibit positive giant magnetoresistance, largest among polycrystalline materials (85%, 75%, and 58% for Tb 2 Ni 3 Si 5 , Sm 2 Ni 3 Si 5 , and Nd 2 Ni 3 Si 5 , respectively, at 4.4 K in a field of 45 kG). These materials have, to the best of our knowledge, the largest positive GMR reported ever for any bulk polycrystalline compounds. The magnitude of MR does not correlate with the rare earth magnetic moments. We believe that the structure of these materials, which can be considered as a naturally occurring multilayer of wavy planes of rare earth atoms separated by Ni endash Si network, plays a role. The isothermal MR of other members of this series (R=Pr,Dy,Ho) exhibits a maximum and a minimum, below their respective T N close-quote s. We interpret these in terms of a metamagnetic transition and short-range ferromagnetic correlations. The short-range ferromagnetic correlations seem to be dominant in the temperature region just above T N . copyright 1997 American Institute of Physics

Ni-CeO2/C Catalysts with Enhanced OSC for the WGS Reaction

Directory of Open Access Journals (Sweden)

Laura Pastor-Pérez

2015-03-01

Full Text Available In this work, the WGS performance of a conventional Ni/CeO2 bulk catalyst is compared to that of a carbon-supported Ni-CeO2 catalyst. The carbon-supported sample resulted to be much more active than the bulk one. The higher activity of the Ni-CeO2/C catalyst is associated to its oxygen storage capacity, a parameter that strongly influences the WGS behavior. The stability of the carbon-supported catalyst under realistic operation conditions is also a subject of this paper. In summary, our study represents an approach towards a new generation of Ni-ceria based catalyst for the pure hydrogen production via WGS. The dispersion of ceria nanoparticles on an activated carbon support drives to improved catalytic skills with a considerable reduction of the amount of ceria in the catalyst formulation.

Effects of Nd-addition on the structural, hydrogen storage, and electrochemical properties of C14 metal hydride alloys

Energy Technology Data Exchange (ETDEWEB)

Wong, D.F. [BASF/Battery Materials-Ovonic, 2983 Waterview Drive, Rochester Hills, MI 48309 (United States); Department of Chemical Engineering, Wayne State University, Detroit, MI 48202 (United States); Young, K., E-mail: kwo.young@basf.com [BASF/Battery Materials-Ovonic, 2983 Waterview Drive, Rochester Hills, MI 48309 (United States); Department of Chemical Engineering, Wayne State University, Detroit, MI 48202 (United States); Nei, J.; Wang, L. [BASF/Battery Materials-Ovonic, 2983 Waterview Drive, Rochester Hills, MI 48309 (United States); Ng, K.Y.S. [Department of Chemical Engineering, Wayne State University, Detroit, MI 48202 (United States)

2015-10-25

Nd-addition to the AB{sub 2}-based alloy Ti{sub 12}Zr{sub 22.8−x}V{sub 10}Cr{sub 7.5}Mn{sub 8.1}Co{sub 7.0}Ni{sub 32.2}Al{sub 0.4}Nd{sub x} is studied for its effects on the structure, gaseous-phase hydrogen storage, and electrochemical properties. This study follows a series of Cu, Mo, Fe, Y, Si, and La doping studies in similar AB{sub 2}-based alloys. Limited solubility of Nd in the main Laves phase promotes the formation of secondary phases (AB and Zr{sub 7}Ni{sub 10}) to provide catalytic effects and synergies for improved capacity and high-rate dischargeability (HRD) performance. The main C14 storage phase has smaller lattice constants and cell volumes, and these effects reduce the storage capacity at higher Nd levels. Different hydrogen absorption mechanisms can occur in these multi-component, multi-phase alloys depending on the interfaces of the phases, and they have effects on the alloy properties. Higher Nd-levels improve the HRD performance despite having lower bulk diffusion and surface exchange current. Magnetic susceptibility measurements indicate large percentage of larger metallic nickel clusters are present in the surface oxide of alloys with higher Nd-content, and AC impedance studies show very low charge-transfer resistance with high catalytic capability in the alloys. The −40 °C charge-transfer resistance of 8.9 Ω g in this Nd-series of alloys is the lowest measured out of the studies investigating doped AB{sub 2}-based MH alloys for improved low-temperature characteristics. The improvement in HRD and low-temperature performance appears to be related to the proportion of the highly catalytic NdNi-phase at the surface, which must offset the increased bulk diffusion resistance in the alloy. - Graphical abstract: Schematics of hydrogen flow and corresponding PCT isotherms in funneling mode. - Highlights: • Structural and hydrogen storage properties of Nd-substituted AB{sub 2} metal hydride are reported. • Nd contributes to the lowest

Neutron diffraction determination of atomic mean-square displacements in cubic compounds of Ni-Al and Ni-Al-Cu systems

International Nuclear Information System (INIS)

Khidirov, I.; Mukhtarova, N.N.

2002-01-01

The atomic mean-square displacements (AMSD) are some of important characteristics of the solid and can be the main information for determination of a number of other characteristics of substances. In the work AMSD is determined for a number of cubic compounds of Ni-Al, Ni-Al-Cu systems immediately from intensities of neutron diffraction maxima. It is shown by the offered method that in all NiAl x and NiAlCu x compounds with the CsCl - type structure AMSD are near each other and they are practically constant. Therefore it is possible to assume that within the homogeneity region of these compounds the interatomic bond forces are changed insignificantly

Synthesis of TiC/Ni cermets via mechanically activated self-propagating high-temperature synthesis

Energy Technology Data Exchange (ETDEWEB)

Dubois, S.; Heian, E.; Karnatak, N.; Beaufort, M.F. [Lab. de Metallurgie Physique, Futuroscope (France); Vrel, D. [Lab. d' Ingenierie des Materiaux et des Hautes Pressions, Villetaneuse (France)

2003-07-01

Stoichiometric mixtures of Ti and C were milled in a high-energy vibratory mill for varying times and the results carefully characterized via X-ray diffraction and TEM. Cermets of stoichiometric TiC and 20 w% Ni were combustion synthesized from non-milled and milled reactant powders, resulting in porous solids composed of roughly spherical TiC particles surrounded by a layer of Ni. Time resolved infrared analysis shows that the kinetics of the reaction performed with milled reactant powders are drastically enhanced over non-milled reactants. This result may be attributed to the microstructure and uniformity of the milled reactant mixtures. It is also demonstrated that mechanical milling of Ti and C powders strongly affects the TiC grain size in the products, most likely due to a reduction in TiC crystal growth as a consequence of the increase in the reaction kinetics. (orig.)

On the nature of Ni···Ni interaction in a model dimeric Ni complex.

Science.gov (United States)

Kamiński, Radosław; Herbaczyńska, Beata; Srebro, Monika; Pietrzykowski, Antoni; Michalak, Artur; Jerzykiewicz, Lucjan B; Woźniak, Krzysztof

2011-06-07

A new dinuclear complex (NiC(5)H(4)SiMe(2)CHCH(2))(2) (2) was prepared by reacting nickelocene derivative [(C(5)H(4)SiMe(2)CH=CH(2))(2)Ni] (1) with methyllithium (MeLi). Good quality crystals were subjected to a high-resolution X-ray measurement. Subsequent multipole refinement yielded accurate description of electron density distribution. Detailed inspection of experimental electron density in Ni···Ni contact revealed that the nickel atoms are bonded and significant deformation of the metal valence shell is related to different populations of the d-orbitals. The existence of the Ni···Ni bond path explains the lack of unpaired electrons in the complex due to a possible exchange channel.

Creep and Oxidation Behavior of Modified CF8C-Plus with W, Cu, Ni, and Cr

Science.gov (United States)

Unocic, Kinga A.; Dryepondt, Sebastien; Yamamoto, Yukinori; Maziasz, Philip J.

2016-04-01

The microstructures of modified CF8C-Plus (Fe-19Cr-12Ni-0.4W-3.8Mn-0.2Mo-0.6Nb-0.5Si-0.9C) with W and Cu (CF8CPWCu) and CF8CPWCu enhanced with 21Cr + 15Ni or 22Cr + 17.5Ni were characterized in the as-cast condition and after creep testing. When imaged at lower magnifications, the as-cast microstructure was similar among all three alloys as they all contained a Nb-rich interdendritic phase and Mn-based inclusions. Transmission electron microscopy (TEM) analysis showed the presence of nanoscale Cu-rich nanoprecipitates distributed uniformly throughout the matrix of CF8CPWCu, whereas in CF8CPWCu22/17, Cu precipitates were found primarily at the grain boundaries. The presence of these nanoscale Cu-rich particles, in addition to W-rich Cr23C6, nanoscale Nb carbides, and Z-phase (Nb2Cr2N2), improved the creep strength of the CF8CPWCu steel. Modification of CF8CPWCu with Cr and Ni contents slightly decreased the creep strength but significantly improved the oxidation behavior at 1073 K (800 °C). In particular, the addition of 22Cr and 17.5Ni strongly enhanced the oxidation resistance of the stainless steel resulting in a 100 degrees or greater temperature improvement, and this composition provided the best balance between improving both mechanical properties and oxidation resistance.

Ni-Doping Effects on Oxygen Removal from an Orthorhombic Mo ₂ C (001) Surface: A Density Functional Theory Study

Energy Technology Data Exchange (ETDEWEB)

Zhou, Mingxia [Department; Cheng, Lei [Materials; Choi, Jae-Soon [Oak Ridge National Laboratory, 1 Bethel Valley Road, Oak Ridge, TN 37831, Unites States; Liu, Bin [Department; Curtiss, Larry A. [Materials; Assary, Rajeev S. [Materials

2018-01-11

Density functional theory (DFT) calculations were used to investigate the effect of Ni dopants on the removal of chemisorbed oxygen (O*) from the Mo-terminated (T-Mo) and C-terminated (Tc) Mo2C(001) surfaces. The removal of adsorbed oxygen from the catalytic site is essential to maintain the long-term activity and selectivity of the carbide catalysts in the deoxygenation process related to bio-oil stabilization and upgrading. In this contribution, the computed reaction energetics and reaction barriers of O* removal were compared among undoped and Ni-doped Mo2C(001) surfaces. The DFT calculations indicate that selected Ni-doped surfaces such as Ni adsorbed on T-Mo and Tc Mo2C(001) surfaces enable weaker binding of important reactive intermediates (O*, OH*) compared to the undoped counterparts, which is beneficial for the O* removal from the catalyst surface. This study thus confirms the promoting effect of the Ni dopant on O* removal reaction on the T-Mo Mo2C(001) and Tc Mo2C(001) surfaces. This computational prediction has been confirmed by the temperature-programmed reduction profiles of Mo2C and Ni-doped Mo2C catalysts, which had been passivated and stored in an oxygen environment.

Development of Cr{sub 3}C{sub 2}-25(Ni20Cr) nanostructured coatings; Desenvolvimento de revestimentos nanostruturados de Cr{sub 3}C{sub 2}-25(Ni20Cr)

Energy Technology Data Exchange (ETDEWEB)

Cunha, Cecilio Alvares da

2012-07-01

This study is divided in two parts. The first part is about the preparation of nanostructured Cr{sub 3}C{sub 2}-25(Ni20Cr) powders by high energy milling followed by characterization of the milled and the as received powder. Analyses of some of the data obtained were done using a theoretical approach. The second part of this study is about the preparation and characterization of coatings prepared with the nanostructured as well as the as received Cr{sub 3}C{sub 2}-25(Ni20Cr) powders. The high temperature erosion-oxidation (E-O) behavior of the coatings prepared with the two types of powders has been compared based on a technological approach. The average crystallite size of the Cr{sub 3}C{sub 2}-25(Ni20Cr) powder decreased rapidly from 145 nm to 50 nm in the initial stages of milling and thereafter decreased slowly to a steady state value of around 10 nm with further increase in milling time. This steady state corresponds to the beginning of a dynamic recovery process. The maximum lattice strain ({epsilon} = 1,17%) was observed in powders milled for 16 hours, and this powders critical crystallite size was 28 nm. In contrast, the lattice parameter attained a minimum for powders milled for 16 hours. Upon reaching the critical crystallite size, the dislocation density attained a steady state regime and all plastic deformation introduced in the material there after was in the form of events occurring at the grain boundaries, due mainly to grain boundary sliding. The deformation energy stored in the crystal lattice of the Cr{sub 3}C{sub 2}-25(Ni20Cr) powders milled for different times was determined from enthalpy variation measurements. These results indicated that the maximum enthalpy variation ({delta}H = 722 mcal) also occurred for powders milled for 16 hours. In a similar manner, the maximum specific heat variation ({delta}C{sub p} = 0,278 cal/gK) occurred for powders milled for 16 hours. The following mechanical properties of Cr{sub 3}C{sub 2}-25(Ni20Cr) coatings

Study of the adsorption, electronic structure and bonding of C2H4 on the FeNi(1 1 1) surface

International Nuclear Information System (INIS)

Simonetti, S.; Brizuela, G.; Juan, A.

2010-01-01

The adsorption of C 2 H 4 on the FeNi(1 1 1) alloy surface has been studied by ASED-MO tight binding calculations. The C 2 H 4 molecule presents its most stable geometry with the C=C bond axis parallel to the surface along the [1, -1, 0] direction, bonded on top Fe atom and bonded along a Fe-Fe bridge site. As a consequence, the strength of the local Fe-Fe bond decreases between 37 and 62% of its original bulk value. This bond weakening is mainly due to the new C-Fe interactions however no Fe 3 C carbide formation is evidenced on surface. The Fe-Ni and Ni-Ni superficial bonds are only slightly modified.

Microstructure and wear behavior of γ/Al4C3/TiC/CaF2 composite coating on γ-TiAl intermetallic alloy prepared by Nd:YAG laser cladding

International Nuclear Information System (INIS)

Liu Xiubo; Shi Shihong; Guo Jian; Fu Geyan; Wang Mingdi

2009-01-01

As a further step in obtaining high performance elevated temperature self-lubrication anti-wear composite coatings on TiAl alloy, a novel Ni-P electroless plating method was adopted to encapsulate the as-received CaF 2 in the preparation of precursor NiCr-Cr 3 C 2 -CaF 2 mixed powders with an aim to decrease its mass loss and increase its compatibility with the metal matrix during a Nd:YAG laser cladding. The microstructure of the coating was examined using X-ray diffraction (XRD), scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS) and the friction and wear behavior of the composite coatings sliding against the hardened 0.45% C steel ring was evaluated using a block-on-ring wear tester at room temperature. It was found that the coating had a unique microstructure consisting of primary dendrites TiC and block Al 4 C 3 carbides reinforcement as well as fine isolated spherical CaF 2 solid lubrication particles uniformly dispersed in the NiCrAlTi (γ) matrix. The good friction-reducing and anti-wear abilities of the laser clad composite coating was suggested to the Ni-P electroless plating and the attendant reduction of mass loss of CaF 2 and the increasing of it's wettability with the NiCrAlTi (γ) matrix during the laser cladding process

Oxidation behavior of a single-crystal Ni-base superalloy between 900 and 1000 {sup o}C in air

Energy Technology Data Exchange (ETDEWEB)

Liu, C.T., E-mail: liuchunting76@yahoo.com.c [College of Electromechanical Engineering, Qingdao University of Science and Technology, Qingdao 266061 (China); Ma, J. [College of Materials Science and Engineering, Qingdao University of Science and Technology, Qingdao 266061 (China); Sun, X.F. [State Key Laboratory for Corrosion and Protection, Institute of Metal Research, Chinese Academy of Sciences, Shenyang 110016 (China)

2010-02-18

The oxidation behavior of a single-crystal Ni-base superalloy DD32 was studied in air at 900 and 1000 {sup o}C and analyzed by X-ray diffraction (XRD), scanning electron microscopy, combined with energy-dispersive X-ray spectroscopy (SEM/EDS). At 900 and 1000 {sup o}C, two oxidation steps appear in the oxidation kinetics. The first one is controlled by NiO growth and the second by Al{sub 2}O{sub 3} growth until a continuous Al{sub 2}O{sub 3} layer formed under the previously grown NiO layer after a critical time. The variations in the chemical composition due to segregations, which resulted from the solidification process, led to the formation of different kinds of oxide scale on the dendritic and interdendritic area during oxidation between 900 and 1000 {sup o}C. The scales formed between 900 and 1000 {sup o}C were complicated, and consisted of three layers: an outer columnar NiO layer with a small amount of CoO, an intermediate layer mainly composed of W{sub 20}O{sub 58}, CrTaO{sub 4}, a small amount of spinels NiCr{sub 2}O{sub 4}, NiAl{sub 2}O{sub 4} and CoAl{sub 2}O{sub 4}, an inner continuous layer of {alpha}-Al{sub 2}O{sub 3}.

Effect of Cr3C2 content on the microstructure and properties of Mo2NiB2-based cermets

International Nuclear Information System (INIS)

Xie, Lang; Li, XiaoBo; Zhang, Dan; Yang, ChengMing; Yin, FuCheng; Xiangtan Univ., Hunan; Xiangtan Univ., Hunan; Xiao, YiFeng

2015-01-01

Four series of Mo 2 NiB 2 -based cermets with Cr 3 C 2 addition of between 0 and 7.5 wt.% in 2.5 wt.% increments were studied by means of scanning electron microscopy, energy dispersive X-ray analysis and X-ray diffractometry. The transverse rupture strength and hardness were also measured. It was found that Cr 3 C 2 completely dissolved in Mo 2 NiB 2 -based cermets. Cr 3 C 2 addition improved the wettability of the Ni binder phase on the Mo 2 NiB 2 hard phase, which resulted in a decrease in the porosity and an increase in the phase uniformity. The cermets with 2.5 wt.% Cr 3 C 2 content showed relatively fine grains and almost full density. A high Cr 3 C 2 content resulted in the formation of M 6 C (M = Mo, Cr, Ni) phase. In addition, energy dispersive X-ray spectroscopy results showed that the content of Mo in the binder decreased with increasing Cr 3 C 2 content. The cermets with 2.5 wt.% Cr 3 C 2 addition exhibited the highest transverse rupture strength of 2210 MPa, whereas the cermets without Cr 3 C 2 addition exhibited the highest hardness.

Tribological properties of B{sub 4}C-TiB{sub 2}-TiC-Ni cermet coating produced by HVOF

Energy Technology Data Exchange (ETDEWEB)

Rafiei, Mahdi [Islamic Azad Univ., Najafabad (Iran, Islamic Republic of). Dept. of Materials Engineering; Isfahan Univ. of Technology, Isfahan (Iran, Islamic Republic of). Depr. of Materials Engineering; Shamanian, Morteza; Salehi, Mehdi [Isfahan Univ. of Technology, Isfahan (Iran, Islamic Republic of). Depr. of Materials Engineering; Mostaan, Hossein [Arak Univ., Arak (Iran, Islamic Republic of). Dept. of Materials and Metallurgical Engineering

2017-08-15

In this study, B{sub 4}C-TiB{sub 2}-TiC-Ni coating was sprayed on the surface of 4130 steel by high velocity oxy-fuel torch. The tribological behavior of samples was studied by ball on disk wear testing. Structural evolution of the coating was analyzed by X-ray diffractometry. The microstructure of the coating, wear track and Al{sub 2}O{sub 3} ball was investigated by scanning electron microscopy, field emission scanning electron microscopy and optical microscopy. Elemental analysis of the wear track was done by energy dispersive X-ray spectroscopy. It was found that a cermet coating containing B{sub 4}C, TiB{sub 2}, TiC and Ni phases with good bonding to the 4130 steel substrate with no sign of any cracking or pores was formed. The wear mechanism of the composite coating was delamination. The friction coefficient of samples was decreased with increasing load because of higher frictional heat and creation of more oxide islands.

Steam reforming of different biomass tar model compounds over Ni/Al_2O_3 catalysts

International Nuclear Information System (INIS)

Artetxe, Maite; Alvarez, Jon; Nahil, Mohamad A.; Olazar, Martin; Williams, Paul T.

2017-01-01

Highlights: • Order of reactivity: anisole > furfural > indene > phenol > toluene > methyl naphthalene. • Higher coke deposition for oxygenates (1.5–2.8%) than for aromatics (0.5–0.8%). • Amorphous coke is deposited for oxygenates and filamentous carbon for aromatics. • Ni content of 20 wt.% shows the higher conversion (90%) and H_2 potential (63%). - Abstract: This work focuses on the removal of the tar derived from biomass gasification by catalytic steam reforming on Ni/Al_2O_3 catalysts. Different tar model compounds (phenol, toluene, methyl naphthalene, indene, anisole and furfural) were individually steam reformed (after dissolving each one in methanol), as well as a mixture of all of them, at 700 °C under a steam/carbon (S/C) ratio of 3 and 60 min on stream. The highest conversions and H_2 potential were attained for anisole and furfural, while methyl naphthalene presented the lowest reactivity. Nevertheless, the higher reactivity of oxygenates compared to aromatic hydrocarbons promoted carbon deposition on the catalyst (in the 1.5–2.8 wt.% range). When the concentration of methanol is decreased in the feedstock and that of toluene or anisole is increased, the selectivity to CO is favoured in the gaseous products, thus increasing coke deposition on the catalyst and decreasing catalyst activity for the steam reforming reaction. Moreover, an increase in Ni loading in the catalyst from 5 to 20% enhances carbon conversion and H_2 formation in the steam reforming of a mixture of all the model compounds studied, but these values decrease for a Ni content of 40%. Coke formation also increased by increasing Ni loading, attaining its maximum value for 40% Ni (6.5 wt.%).

Disorder controlled electrical transport properties of NdCo1−xNiO3

International Nuclear Information System (INIS)

Kumar, Vinod; Kumar, Rajesh; Shukla, D.K.; Kumar, Ravi

2013-01-01

Highlights: •Single phase NdCo 1−x Ni x O 3 were prepared using solid state reaction method. •Drastic improvement in room temperature conductivity for substituted samples. •Arrhenius and VRH conduction models employed to explain electrical transport. •Disorder induced charge carrier localization dominates in the substituted samples. -- Abstract: The effect of Ni substitution on structural and electrical transport has been investigated in NdCo 1−x Ni x O 3 system for 0 ⩽ x ⩽ 0.5. The Rietveld refinement of XRD data confirms orthorhombic, Pbnm symmetry for all the samples. The lattice parameters and hence unit cell volume is found to increase linearly with increase in Ni concentration. Substitution of Ni leads to the increase in conductivity and samples have been found to display semiconducting behavior in measured range of temperature. The explanation for the variation of resistivity with substitution and temperature has been provided on the basis of substitutional disorder and spin state related effects. Arrhenius and variable range hopping conduction approaches have been used to explain the temperature variation of resistivity. These results suggest that disorder-induced localization of charge carriers dominate the electrical transport in the substituted samples

Microstructure and wear behaviors of laser clad NiCr/Cr3C2-WS2 high temperature self-lubricating wear-resistant composite coating

Science.gov (United States)

Yang, Mao-Sheng; Liu, Xiu-Bo; Fan, Ji-Wei; He, Xiang-Ming; Shi, Shi-Hong; Fu, Ge-Yan; Wang, Ming-Di; Chen, Shu-Fa

2012-02-01

The high temperature self-lubricating wear-resistant NiCr/Cr3C2-30%WS2 coating and wear-resistant NiCr/Cr3C2 coating were fabricated on 0Cr18Ni9 austenitic stainless steel by laser cladding. Phase constitutions and microstructures were investigated, and the tribological properties were evaluated using a ball-on-disc wear tester under dry sliding condition at room-temperature (17 °C), 300 °C and 600 °C, respectively. Results indicated that the laser clad NiCr/Cr3C2 coating consisted of Cr7C3 primary phase and γ-(Fe,Ni)/Cr7C3 eutectic colony, while the coating added with WS2 was mainly composed of Cr7C3 and (Cr,W)C carbides, with the lubricating WS2 and CrS sulfides as the minor phases. The wear tests showed that the friction coefficients of two coatings both decrease with the increasing temperature, while the both wear rates increase. The friction coefficient of laser clad NiCr/Cr3C2-30%WS2 is lower than the coating without WS2 whatever at room-temperature, 300 °C, 600 °C, but its wear rate is only lower at 300 °C. It is considered that the laser clad NiCr/Cr3C2-30%WS2 composite coating has good combination of anti-wear and friction-reducing capabilities at room-temperature up to 300 °C.

Large magnetocaloric effect of GdNiAl2 compound

International Nuclear Information System (INIS)

Dembele, S.N.; Ma, Z.; Shang, Y.F.; Fu, H.; Balfour, E.A.; Hadimani, R.L.; Jiles, D.C.; Teng, B.H.; Luo, Y.

2015-01-01

This paper presents the structure, magnetic properties, and magnetocaloric effect of the polycrystalline compound GdNiAl 2 . Powder X-ray diffraction (XRD) measurement and Rietveld refinement revealed that GdNiAl 2 alloy is CuMgAl 2 -type phase structure with about 1 wt% GdNi 2 Al 3 secondary phase. Magnetic measurements suggest that the compound is ferromagnetic and undergoes a second-order phase transition near 28 K. The maximum value of magnetic entropy change reaches 16.0 J/kg K for an applied magnetic field change of 0–50 kOe and the relative cooling power was 6.4×10 2 J/kg. It is a promising candidate as a magnetocaloric material working near liquid hydrogen temperature (~20 K) exhibiting large relative cooling power. - Highlights: • Preferred orientation with axis of [010] was found in the GdNiAl 2 compound. • The ΔS Mmax and the RCP are 16.0 J/kg K and 640 J/kg, respectively, for ΔH=50 kOe. • Relative low rare earth content in GdNiAl 2 comparing with other candidates

Phase transitions in alloys of the Ni-Mo system

International Nuclear Information System (INIS)

Ustinovshikov, Y.; Shabanova, I.

2011-01-01

Graphical abstract: The structure of Ni-20 at.% Mo and Ni-25 at.% Mo alloys was studied by methods of TEM and XPS. It is shown that at high temperatures the tendency toward phase separation takes place in the alloys and crystalline bcc Mo particles precipitate in the liquid solution. At 900 deg. C and below, the tendency toward ordering leads to the dissolution of Mo particles and precipitation of the particles of Ni 3 Mo, Ni 2 Mo or Ni 4 Mo chemical compounds. Highlights: → 'Chemical' phase transition 'ordering-phase separation' is first discovered in alloys of the Ni-Mo system. → It is first shown that the phase separation in the alloys studied begins at temperatures above the liquidus one. → The formation of Ni 3 Mo from A1 has gone through the intervening stage of the Ni 4 Mo and Ni 2 Mo coexistence. - Abstract: The structure of Ni-20 at.% Mo and Ni-25 at.% Mo alloys heat treated at different temperatures was studied by the method of transmission electron microscopy. X-ray photoelectron spectroscopy was used to detect the sign of the chemical interaction between Ni and Mo atoms at different temperatures. It is shown that at high temperatures the tendency toward phase separation takes place. The system of additional reflections at positions {1 1/2 0} on the electron diffraction patterns testifies that the precipitation of crystalline bcc Mo particles begins in the liquid solution. At 900 deg. C and below, the tendency toward ordering leads to the precipitation of the particles of the chemical compounds. A body-centered tetragonal phase Ni 4 Mo (D1 a ) is formed in the Ni-20 at.% Mo alloy. In the Ni-25 at.% Mo alloy, the formation of the Ni 3 Mo (D0 22 ) chemical compound from the A1 solid solution has gone through the intervening stage of the Ni 4 Mo (D1 a ) and Ni 2 Mo (Pt 2 Mo) formation.

Combining Ru, Ni and Ni(OH){sub 2} active sites for improving catalytic performance in benzene hydrogenation

Energy Technology Data Exchange (ETDEWEB)

Zhu, Lihua, E-mail: lihuazhu@stu.xmu.edu.cn [School of Metallurgy and Chemical Engineering, Jiangxi University of Science and Technology, Ganzhou 341000, Jiang Xi (China); Department of Chemical and Biochemical Engineering, National Engineering Laboratory for Green Productions of Alcohols-Ethers-Esters, College of Chemistry and Chemical Engineering, Xiamen University, Xiamen 361005 (China); Sun, Hanlei; Zheng, Jinbao [Department of Chemical and Biochemical Engineering, National Engineering Laboratory for Green Productions of Alcohols-Ethers-Esters, College of Chemistry and Chemical Engineering, Xiamen University, Xiamen 361005 (China); Yu, Changlin, E-mail: yuchanglinjx@163.com [School of Metallurgy and Chemical Engineering, Jiangxi University of Science and Technology, Ganzhou 341000, Jiang Xi (China); Zhang, Nuowei [Department of Chemical and Biochemical Engineering, National Engineering Laboratory for Green Productions of Alcohols-Ethers-Esters, College of Chemistry and Chemical Engineering, Xiamen University, Xiamen 361005 (China); Shu, Qing [School of Metallurgy and Chemical Engineering, Jiangxi University of Science and Technology, Ganzhou 341000, Jiang Xi (China); Chen, Bing H., E-mail: chenbh@xmu.edu.cn [Department of Chemical and Biochemical Engineering, National Engineering Laboratory for Green Productions of Alcohols-Ethers-Esters, College of Chemistry and Chemical Engineering, Xiamen University, Xiamen 361005 (China)

2017-05-01

In this study, the Ru{sub 0.04}Ni{sub 0.96}/C(T) catalysts were successfully prepared by the simple methods of hydrazine-reduction and galvanic replacement, where 0.04/0.96 and T represented the Ru/Ni atomic ratio and reducing temperature of the catalyst in N{sub 2}+10%H{sub 2}, respectively. The nanostructures of the Ru{sub 0.04}Ni{sub 0.96} nanoparticles in the Ru{sub 0.04}Ni{sub 0.96}/C(T) catalysts were controlled by modulating their annealing temperature in N{sub 2}+10%H{sub 2} and characterized by an array of techniques, including X-ray diffraction (XRD), X-ray photoelectron spectroscopy (XPS), transmission electron microscopy (TEM), high resolution transmission electron microscopy (HRTEM), scanning transmission electron microscopy energy dispersive X-ray spectroscopy (STEM-EDS) mapping and high-sensitivity low-energy ion scattering (HS-LEIS). The Ru{sub 0.04}Ni{sub 0.96}/C(30) catalyst, which was composed of Ru clusters or single atoms supported on Ni/Ni(OH){sub 2} nanoparticles, exhibited much better catalytic performance for benzene hydrogenation than the Ru{sub 0.04}Ni{sub 0.96}/C(T) catalysts reduced at above 30 °C, such as Ru{sub 0.04}Ni{sub 0.96}/C(160) with the nanostructure of partial Ru{sub 0.04}Ni{sub 0.9} alloy and Ru{sub 0.04}Ni{sub 0.96}/C(280) with the nanostructure of complete Ru{sub 0.04}Ni{sub 0.9} alloy. The reason was that the synergistic effect of multiple active sites – Ru, Ni and Ni(OH){sub 2} sites was present in the Ru{sub 0.04}Ni{sub 0.96}/C(30) catalyst, where hydrogen was preferentially activated at Ru sites, benzene was probably activated at Ni(OH){sub 2} surface and Ni acted as a “bridge” for transferring activated H{sup ∗} species to activated benzene by hydrogen spillover effect, hydrogenating and forming product – cyclohexane. This study also provided a typical example to illustrate that the synergy effect of multiple active sites can largely improve the catalytic hydrogenation performance. - Highlights: • The Ru

Nitriding behavior of Ni and Ni-based binary alloys

Energy Technology Data Exchange (ETDEWEB)

Fonovic, Matej

2015-01-15

Gaseous nitriding is a prominent thermochemical surface treatment process which can improve various properties of metallic materials such as mechanical, tribological and/or corrosion properties. This process is predominantly performed by applying NH{sub 3}+H{sub 2} containing gas atmospheres serving as the nitrogen donating medium at temperatures between 673 K and 873 K (400 C and 600 C). NH{sub 3} decomposes at the surface of the metallic specimen and nitrogen diffuses into the surface adjacent region of the specimen whereas hydrogen remains in the gas atmosphere. One of the most important parameters characterizing a gaseous nitriding process is the so-called nitriding potential (r{sub N}) which determines the chemical potential of nitrogen provided by the gas phase. The nitriding potential is defined as r{sub N} = p{sub NH{sub 3}}/p{sub H{sub 2}{sup 3/2}} where p{sub NH{sub 3}} and p{sub H{sub 2}} are the partial pressures of the NH{sub 3} and H{sub 2} in the nitriding atmosphere. In contrast with nitriding of α-Fe where the nitriding potential is usually in the range between 0.01 and 1 atm{sup -1/2}, nitriding of Ni and Ni-based alloys requires employing nitriding potentials higher than 100 atm{sup -1/2} and even up to ∞ (nitriding in pure NH{sub 3} atmosphere). This behavior is compatible with decreased thermodynamic stability of the 3d-metal nitrides with increasing atomic number. Depending on the nitriding conditions (temperature, nitriding potential and treatment time), different phases are formed at the surface of the Ni-based alloys. By applying very high nitriding potential, formation of hexagonal Ni{sub 3}N at the surface of the specimen (known as external nitriding) leads to the development of a compound layer, which may improve tribological properties. Underneath the Ni{sub 3}N compound layer, two possibilities exist: (i) alloying element precipitation within the nitrided zone (known as internal nitriding) and/or (ii) development of metastable and

Magnetic properties of intermetallic compounds La(Ni,Co,Cu)3

International Nuclear Information System (INIS)

Tazuke, Y.; Tanikawa, H.; Okano, A.; Miyaji, T.

2006-01-01

LaNi 3 exhibited a metallic antiferromagnetic property with T N =30 K. La(Ni 1-x Co x ) 3 with x=0.01, 0.03 and 0.05 exhibited ferromagnetic properties, T C increasing linearly with increasing x. La(Ni 1-2z Co z Cu z ) 3 with z=0.015 exhibited a ferromagnetic property with a small T C . A La(Ni 1-y Cu y ) 3 sample with y=0.01 exhibited a Pauli-paramagnetic property; those with y=0.02, 0.03 and 0.04 exhibited gradual metamagnetic behavior and that with y=0.05 exhibited a ferromagnetic property. The gradual metamagnetic M-H variations are numerically simulated by using Landau-type free energies. The results suggest that the gradual metamagnetic behavior occurs from an antiferromagnetic state to a ferromagnetic one. (copyright 2006 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim) (Abstract Copyright [2006], Wiley Periodicals, Inc.)

Direct evidence of Ni magnetic moment in TbNi{sub 2}Mn—X-ray magnetic circular dichroism

Energy Technology Data Exchange (ETDEWEB)

Yu, D.H., E-mail: dyu@ansto.gov.au [Bragg Institute, Australian Nuclear Science and Technology Organisation, Lucas Heights, Sydney, NSW 2234 (Australia); Huang, Meng-Jie [National Synchrotron Radiation Research Center, 101 Hsin-Ann Road, Hsinchu Science Park, Hsinchu 30076, Taiwan (China); Wang, J.L. [Bragg Institute, Australian Nuclear Science and Technology Organisation, Lucas Heights, Sydney, NSW 2234 (Australia); School of Physical, Environmental and Mathematical Sciences, University of New South Wales, Canberra at the Australian Defense Force Academy, Sydney, ACT 2600 (Australia); Institute for Superconductivity and Electronic Materials, University of Wollongong, Wollongong, NSW 2522 (Australia); Su, Hui-Chia; Lin, Hong-Ji; Chen, Chien-Te [National Synchrotron Radiation Research Center, 101 Hsin-Ann Road, Hsinchu Science Park, Hsinchu 30076, Taiwan (China); Campbell, S.J. [School of Physical, Environmental and Mathematical Sciences, University of New South Wales, Canberra at the Australian Defense Force Academy, Sydney, ACT 2600 (Australia)

2014-12-15

We have investigated the individual magnetic moments of Ni, Mn and Tb atoms in the intermetallic compound TbNi{sub 2}Mn in the Laves phase (magnetic phase transition temperature T{sub C} ∼131 K) by X-ray magnetic circular dichroism (XMCD) studies at 300 K, 80 K and 20 K. Analyses of the experimental results reveal that Ni atoms at 20 K in an applied magnetic field of 1 T carry an intrinsic magnetic moment of spin and orbital magnetic moment contributions 0.53±0.01 μ{sub B} and 0.05±0.01 μ{sub B}, respectively. These moment values are similar to those of the maximum saturated moment of Ni element. A very small magnetic moment of order <0.1 μ{sub B} has been measured for Mn. This suggests that Mn is antiferromagnetically ordered across the two nearly equally occupied sites of 16d and 8a. A magnetic moment of up to ∼0.3 μ{sub B} has been observed for the Tb atoms. Identification of a magnetic moment on the Ni atoms has provided further evidence for the mechanism of enhancement of the magnetic phase transition temperature in TbNi{sub 2}Mn compared with TbNi{sub 2} (T{sub C}∼37.5 K) and TbMn{sub 2} (T{sub C}∼54 K) due to rare earth–transition metal (R–T) and transition metal–transition metal (T–T) interactions. The behaviour of the X-ray magnetic circular dichroism spectra of TbNi{sub 2}Mn at 300 K, 80 K and 20 K – above and below the magnetic ordering temperature T{sub C} ∼131 K – is discussed. - Highlights: • We study the magnetic moment of TbNi{sub 2}Mn with XMCD. • We observe directly the Ni intrinsic magnetic moment in TbNi{sub 2}Mn. • We find that Mn ordered antiferromagnetically across the 16d and 8a sites. • We confirm the mechanism for increasing the magnetic phase transition temperature.

Diffusion complex layers of TiC-Ni-Mo type produced on steel during vacuum titanizing process combined with the electrolytic deposition

International Nuclear Information System (INIS)

Kasprzycka, E.; Krolikowski, A.

1999-01-01

Diffusion carbide layers produced on steel surface by means of vacuum titanizing process have been studied. A new technological process combining a vacuum titanizing with an electrolytic deposition of Ni-Mo alloy has been proposed to increase of corrosion resistance of carbide layers. The effect of preliminary electrolytic deposition of Ni-Mo alloy on the NC10 steel surface on the titanized layer structure and its corrosion resistance has ben investigated. As a result, diffusion complex layers of TiC-Ni-Mo type on NC10 steel surface have been obtained. An X-ray structural analysis of titanized surfaces on NC10 steel precovered with an electrolytic Ni-Mo alloy coating (70%Ni+30%Mo) revealed a presence of titanium carbide TiC, NiTi, MoTi and trace quantity of austenite. The image of the TiC-Ni-Mo complex layer on NC10 steel surface obtained by means of joined SEM+TEM method and diagrams of elements distribution in the layer diffusion zone have been shown. Concentration of depth profiles of Ti, Ni, Mo, Cr and Fe in the layer diffusion zone obtained by means of the joined EDS+TEM method are shown. Concentration depth profiles of Ti, Ni, Mo, Cr and Fe in the layer diffusion zone obtained by means of the X r ay microanalysis and microhardness of the layer are shown. An X-ray structural analysis of titanized surfaces on the NC10 steel, without Ni-Mo alloy layer, revealed only a substantial presence of titanium carbide TiC. For corrosion resistance tests the steel samples with various diffusion layers and without layers were used: (i) the TiC-Ni-Mo titanized complex layers on NC10 steel, (ii) the TiC titanized carbide layers on the NC10 steel, (iii) the NC10 steel without layers. Corrosion measurements of sample under test have been performed in 0.1 M H 2 SO 4 by means of potentiodynamic polarization and electrochemical impedance tests. It has been found that the corrosion resistance of titanized steel samples with the TiC and TiC-Ni-Mo layers is higher than for the steel

Fabrication and thermal characterization of amorphous and nanocrystalline Al{sub 9}FeNi/Al{sub 3}Ti compound

Energy Technology Data Exchange (ETDEWEB)

Tavoosi, Majid, E-mail: ma.tavoosi@gmail.com

2017-01-15

In this study, the fabrication and structural characterization of amorphous/nanocrystalline Al{sub 9}FeNi/Al{sub 3}Ti phase has been performed. In this regards, milling and annealing processes were applied on Al{sub 80}Fe{sub 10}Ti{sub 5}Ni{sub 5} (at. %) powder mixture for different periods of time. The prepared samples were characterized using X-ray diffraction (XRD), scanning and transmission electron microscopy (SEM and TEM) and differential scanning calorimetery (DSC). According to the results, supersaturated solid solution, nanocrystalline Al{sub 9}FeNi/Al{sub 3}Ti (with average crystallite size of about 7 nm) and amorphous phases indicated three different microstructures which can be formed in Al{sub 80}Fe{sub 10}Ti{sub 5}Ni{sub 5} system during milling process. The formed supersaturated solid solution and amorphous phases were unstable and transformed to Al{sub 9}FeNi/Al{sub 3}Ti intermetallic compound during annealing process. It is shown that, Al{sub 9}FeNi phase in Al{sub 9}FeNi/Al{sub 3}Ti intermetallic compound can decompose into Al{sub 3}Ni, Al{sub 13}Fe{sub 4} and liquid phases during a reversible peritectic reaction at 809 °C. - Highlights: • We study the effect of milling process on Al{sub 80}Fe{sub 10}Ti{sub 5}Ni{sub 5} alloy. • We study the effect of annealing on Al{sub 80}Fe{sub 10}Ti{sub 5}Ni{sub 5} supersaturated solid solution phase. • We study the effect of annealing on Al{sub 80}Fe{sub 10}Ti{sub 5}Ni{sub 5} amorphous phase. • We study the thermal behaviour of Al{sub 9}FeNi/Al{sub 3}Ti compound.

Effect of W content in solid solution on properties and microstructure of (Ti,W)C-Ni{sub 3}Al cermets

Energy Technology Data Exchange (ETDEWEB)

Huang, Bin; Xiong, Weihao, E-mail: whxiong@hust.edu.cn; Zhang, Man; Jing, Yong; Li, Baolong; Luo, Haifeng; Wang, Shengqing

2016-08-15

(Ti{sub 1-x}W{sub x})C solid solutions (x = 0.05, 0.15, 0.25, 0.35) were synthesized by carbothermal reduction and then were used as hard phases to prepare (Ti,W)C-Ni{sub 3}Al cermets by vacuum sintering. (Ti,W)C-Ni{sub 3}Al cermets showed weak core-rim structure carbide particles embedded in Ni{sub 3}Al binder. As W content in (Ti,W)C increased, core-rim structure of carbide particles got weaker and the contrast of particles lowered down in SEM-BSE morphologies. Furthermore, the densification of cermets was promoted with W content in solid solution increasing, meanwhile TRS and toughness of cermets were improved obviously. In this paper, the wettability of molten metal on different group transition metal carbides was discussed in detail based on valence-electron configurations (VECs) of carbides. - Highlights: • (Ti{sub 1-x}W{sub x})C solid solutions were synthesized by carbothermal reduction. • (Ti,W)C-Ni{sub 3}Al cermets were prepared through powder metallurgy route. • The increase of W can improve wetting and densification significantly. • (Ti,W)C-Ni{sub 3}Al cermets showed a weak core-rim structure particles embedded in binder. • Wetting behavior were discussed from valence-electron configurations of carbides.

Protonation and structural/chemical stability of Ln{sub 2}NiO{sub 4+δ} ceramics vs. H{sub 2}O/CO{sub 2}: High temperature/water pressure ageing tests

Energy Technology Data Exchange (ETDEWEB)

Upasen, S. [Sorbonne Universités, UPMC Univ Paris 06, UMR 8233, MONARIS, 75005 Paris (France); CNRS-IP2CT, UMR 8233, MONARIS, F-75005 Paris (France); Batocchi, P.; Mauvy, F. [ICMCB, ICMCB-CNRS-IUT-Université de Bordeaux, 33608 Pessac Cedex (France); Slodczyk, A. [Sorbonne Universités, UPMC Univ Paris 06, UMR 8233, MONARIS, 75005 Paris (France); CNRS-IP2CT, UMR 8233, MONARIS, F-75005 Paris (France); Colomban, Ph., E-mail: philippe.colomban@upmc.fr [Sorbonne Universités, UPMC Univ Paris 06, UMR 8233, MONARIS, 75005 Paris (France); CNRS-IP2CT, UMR 8233, MONARIS, F-75005 Paris (France)

2015-02-15

Highlights: • High temperature/water pressure autoclave is used to study the reaction/corrosion at SOFC/HTSE electrode. • High stability of Pr{sub 2}NiO{sub 4+δ} (PNO) and Nd{sub 2}NiO{sub 4+δ} (NNO) dense ceramics vs. water pressure is demonstrated. • Protonated rare-earth nickelates retain the perovskite-type structure and their H-content is determined. • Very low laser illumination power is required to avoid RE nickelate phase transition. • Nickelates show increasing stability from La to Pr/Nd vs. CO{sub 2}-rich high temperature water vapor. - Abstract: Mixed ionic-electronic conductors (MIEC) such as rare-earth nickelates with a general formula Ln{sub 2}NiO{sub 4+δ} (Ln = La, Pr, Nd) appear as potential for energy production and storage systems: fuel cells, electrolysers and CO{sub 2} converters. Since a good electrode material should exhibit important stability in operating conditions, the structural and chemical stability of different nickelate-based, well-densified ceramics have been studied using various techniques: TGA, dilatometry, XRD, Raman scattering and IR spectroscopy. Consequently, La{sub 2}NiO{sub 4+δ} (LNO), Pr{sub 2}NiO{sub 4+δ} (PNO) and Nd{sub 2}NiO{sub 4+δ} (NNO) have been exposed during 5 days to high water vapor pressure (40 bar) at intermediate temperature (550 °C) in an autoclave device, the used water being almost free or saturated with CO{sub 2}. Such protonation process offers an accelerating stability test and allows the choice of the most pertinent composition for industrial applications requiring a selected material with important life-time. In order to understand any eventual change of crystal structure, the ceramics were investigated in as-prepared, pristine state as well as after protonation and deprotonation (due to thermal treatment till 1000 °C under dry atmosphere). The results show the presence of traces or second phases originating from undesirable hydroxylation and carbonation, detected in the near

Neutron diffraction studies of magnetic ordering in superconducting ErNi{sub 2}B{sub 2}C and TmNi{sub 2}B{sub 2}C in an applied magnetic field

Energy Technology Data Exchange (ETDEWEB)

Toft, K.N

2004-01-01

The field-induced magnetic structures of ErNi{sub 2}B{sub 2}C and TmNi{sub 2}B{sub 2}C in are especially interesting because the field suppresses the superconducting order parameter and therefore the magnetic properties can be studied while varying the strength of superconductivity. ErNi{sub 2}B{sub 2}C: For magnetic fields along all three symmetry directions, the observed magnetic structures have a period corresponding to the Fermi surface nesting structure. The phase diagrams present all the observed magnetic structures. Two results remain unresolved: 1. When applying the magnetic field along [010], the minority domain (Q{sub N}{sup B} = (0,Q,0) with moments perpendicular to the field) shows no signs of hysteresis. I expected it to be a meta-stable state, which would be gradually suppressed by a magnetic field, and when decreasing the field it would not reappear until some small field of approximately 0.1 T. 2. When the field is applied along [110], the magnetic structure rotates a small angle of 0.5 degrees away from the symmetry direction. TmNi{sub 2}B{sub 2}C: A magnetic field applied in the [100] direction suppresses the zero field magnetic structure Q{sub F} = (0.094,0.094,0) (T{sub N} = 1.6 K), in favor of the Fermi surface nesting structure Q{sub N} = (0.483,0,0). The appearance of the Q{sub N} phase was initially believed to be caused by the suppression of superconductivity. This suppression should make it favorable to create a magnetic order with a Q-vector determined by the maximum in the magnetic susceptibility at the Fermi surface nesting vector Q{sub N}. The phase diagram for the magnetic structures is presented, however several properties of the Q{sub N} magnetic structure cannot be explained within any known models. Quadrupolar ordering is suggested as a possible candidate for explaining these features of the Q{sub N} structure. (au)

The mechanism of hard metal TiC-TiNi composite liquid-phase sintering

International Nuclear Information System (INIS)

Akimov, V.V.

2006-01-01

The sintering conditions are investigated for hard alloys on their production from powders of titanium nickelide with particle size of 10-25 μ and titanium carbide with particles of 5-10 μ at temperatures of 1280-1350 deg C under pressure of 0.1 MPa with holding at heat for 180-900 s. The analysis of experimental data shows that optimum sintering conditions are determined by the quantity of a binding phase TiNi. In the systems with a binding phase content no more than 40 % a heterogeneous structure with nonuniform aggregates of TiC and TiNi phases is observed. With increasing a binding phase amount up to 50-70 % and a temperature up to 1350 deg C, titanium nickelide melts and spreads uniformly among carbide grains. This results in a low porosity of the composite material and in an increase of thermodynamic stability of the system [ru

Ni-YSZ Substrate Degradation during Carbon Deposition

Directory of Open Access Journals (Sweden)

Marinšek, Marjan

2011-06-01

contrario, en el metano bajo una atmósfera húmeda con un ratio S/C de 0.82, la actividad catalizadora de los compuestos Ni-YSZ permaneció prácticamente sin disminuciones luego de 2,000 minutos bajo las temperaturas de deposición seleccionadas (600–800 °C. En la superficie de catalización se observó cierta encapsulación de Ni con el carbón depositado, mientras que los filamentos de carbón se desarrollaron dentro de las pruebas tratadas. Las dimensiones de los filamentos C fueron influenciados por las condiciones del tratamiento y la morfología del sustrato Ni-YSZ.

Quaternary rare-earth sulfides RE{sub 3}M{sub 0.5}GeS{sub 7} (RE=La–Nd, Sm; M=Co, Ni) and Y{sub 3}Pd{sub 0.5}SiS{sub 7}

Energy Technology Data Exchange (ETDEWEB)

Iyer, Abishek K. [Department of Chemistry, University of Alberta, Edmonton, Alberta, Canada T6G 2G2 (Canada); Yin, Wenlong [Department of Chemistry, University of Alberta, Edmonton, Alberta, Canada T6G 2G2 (Canada); Institute of Chemical Materials, China Academy of Engineering Physics, Mianyang 621900 (China); Lee, Emma J. [Department of Chemistry, University of Alberta, Edmonton, Alberta, Canada T6G 2G2 (Canada); Lin, Xinsong [Centre for Oil Sands Sustainability, Northern Alberta Institute of Technology, Edmonton, Alberta, Canada T6N 1E5 (Canada); Mar, Arthur, E-mail: arthur.mar@ualberta.ca [Department of Chemistry, University of Alberta, Edmonton, Alberta, Canada T6G 2G2 (Canada)

2017-06-15

The two metal-deficient series of quaternary Ge-containing sulfides RE{sub 3}M{sub 0.5}GeS{sub 7} (RE = La–Nd, Sm; M = Co, Ni), as well as the related Si-containing sulfide Y{sub 3}Pd{sub 0.5}SiS{sub 7}, were prepared by reactions of the elements at 1050 °C. Single-crystal X-ray diffraction analysis performed on all compounds confirmed noncentrosymmetric hexagonal structures (space group P6{sub 3}, Z =2) with cell parameters in the ranges of a =10.0–10.3 Å and c =5.7–5.8 Å for RE{sub 3}Co{sub 0.5}GeS{sub 7} and RE{sub 3}Ni{sub 0.5}GeS{sub 7}, or a =9.7891(3) Å and c =5.6840(4) Å for Y{sub 3}Pd{sub 0.5}SiS{sub 7}. They are classified as La{sub 3}Mn{sub 0.5}SiS{sub 7}-type structures, with M atoms centred within octahedra (in contrast to La{sub 3}CuSiS{sub 7}-type structures in which M atoms occupy trigonal planar sites) and Ge atoms centred within tetrahedra, both types of polyhedra being arranged in one-dimensional stacks aligned along the c-direction. Charge balance requirements dictate half-occupancy of the M sites. However, bond valence sum arguments indicated that the M atoms are somewhat underbonded within these octahedral sites, so that there is evidence that in some compounds, they can also enter the trigonal planar site at low occupancy (~5%). Magnetic measurements on RE{sub 3}Co{sub 0.5}GeS{sub 7} (RE = Ce, Pr, Sm) revealed paramagnetic behaviour for the Ce and Pr members and apparent antiferromagnetic ordering (T{sub N} =14 K) for the Sm member; fitting to the Curie-Weiss law gave effective magnetic moments consistent with the presence of RE{sup 3+} and Co{sup 2+} species. Band structure calculations on ordered models of La{sub 3}M{sub 0.5}GeS{sub 7} (M = Co, Ni) showed that the Fermi level cuts through M 3d states in the DOS curve and supported the presence of strong M–S and Ge–S bonding interactions. - Graphical abstract: RE{sub 3}M{sub 0.5}GeS{sub 7} (M = Co, Ni) and Y{sub 3}Pd{sub 0.5}SiS{sub 7} contain M atoms partially occupying

Study of hyperfine interactions in intermetallic compounds Gd(Ni,Pd,Cu)In, Tb(Ni,Pd)In, Dy(Ni,Pd)In and Ho(Ni,Pd)In; Estudo de interacoes hiperfinas em compostos intermetalicos Gd(Ni,Pd,Cu)In, Tb(Ni,Pd)In, Dy(Ni,Pd)In e Ho(Ni,Pd)In

Energy Technology Data Exchange (ETDEWEB)

Lapolli, Andre Luis

2006-07-01

Systematic behavior of magnetic hyperfine field (B{sub hf}) in the intermetallic compounds Gd(Ni,Pd,Cu)In Tb(Ni,Pd)In, Dy(Ni,Pd)In and Ho(Ni,Pd)In was studied by Perturbed Gamma-Gamma Angular Correlation spectroscopy. The measurements of B{sub hf} were carried out at the rare earth atom and in sites using the nuclear probes {sup 140}Ce and {sup 11}'1Cd respectively. The variation of hyperfine field with temperature, in most cases, follows the Brillouin function predicted from the molecular field theory. The hyperfine field values at rare earth atom sites obtained from {sup 140}Ce probe as well as at in sites obtained from {sup 111}Cd probe for each series of compounds were extrapolated to zero Kelvin B{sub hf}(T=0) from these curves. These values were compared with the values of the literature for other compounds containing the same rare earth element and all of them show a linear relationship with the ordering temperature. This indicates that the main contribution to B{sub hf} comes from the conduction electron polarization (CEP) through Fermi contact interaction and the principal mechanism of magnetic interaction in these compounds can be described by the RKKY type interaction. The values of B{sub hf}(T=0) for each family of intermetallic compounds RNiIn and RPdIn when plotted as a function of 4f spin projection of rare earth element also shows a linear relationship. Exceptions are the results for the compounds RNiIn obtained with {sup 111}Cd probe where a small deviation from linearity is observed. The results of the measurements carried out with the {sup 111}Cd probe were also analyzed to obtain the hyperfine parameters of the quadrupole interaction as a function of temperature for RPdln and GdNiIn compounds. The results show that for the compound GdPdIn there might be some Gd-In disorder at high temperature. (author)

Study of hyperfine interactions in intermetallic compounds Gd(Ni,Pd,Cu)In, Tb(Ni,Pd)In, Dy(Ni,Pd)In and Ho(Ni,Pd)In; Estudo de interacoes hiperfinas em compostos intermetalicos Gd(Ni,Pd,Cu)In, Tb(Ni,Pd)In, Dy(Ni,Pd)In e Ho(Ni,Pd)In

Energy Technology Data Exchange (ETDEWEB)

Lapolli, Andre Luis

2006-07-01

Systematic behavior of magnetic hyperfine field (B{sub hf}) in the intermetallic compounds Gd(Ni,Pd,Cu)In Tb(Ni,Pd)In, Dy(Ni,Pd)In and Ho(Ni,Pd)In was studied by Perturbed Gamma-Gamma Angular Correlation spectroscopy. The measurements of B{sub hf} were carried out at the rare earth atom and in sites using the nuclear probes {sup 140}Ce and {sup 11}'1Cd respectively. The variation of hyperfine field with temperature, in most cases, follows the Brillouin function predicted from the molecular field theory. The hyperfine field values at rare earth atom sites obtained from {sup 140}Ce probe as well as at in sites obtained from {sup 111}Cd probe for each series of compounds were extrapolated to zero Kelvin B{sub hf}(T=0) from these curves. These values were compared with the values of the literature for other compounds containing the same rare earth element and all of them show a linear relationship with the ordering temperature. This indicates that the main contribution to B{sub hf} comes from the conduction electron polarization (CEP) through Fermi contact interaction and the principal mechanism of magnetic interaction in these compounds can be described by the RKKY type interaction. The values of B{sub hf}(T=0) for each family of intermetallic compounds RNiIn and RPdIn when plotted as a function of 4f spin projection of rare earth element also shows a linear relationship. Exceptions are the results for the compounds RNiIn obtained with {sup 111}Cd probe where a small deviation from linearity is observed. The results of the measurements carried out with the {sup 111}Cd probe were also analyzed to obtain the hyperfine parameters of the quadrupole interaction as a function of temperature for RPdln and GdNiIn compounds. The results show that for the compound GdPdIn there might be some Gd-In disorder at high temperature. (author)

Influence of the substitution of Ni for Fe on the microstructure evolution and magnetic phase transition in La(Fe1−xNix)11.5Si1.5 compounds

International Nuclear Information System (INIS)

Sun, Song; Ye, Rongchang; Long, Yi

2013-01-01

Graphical abstract: M–T curves show that all the compounds undergo a ferromagnetic–paramagnetic magnetic phase transition process. Besides, the Curie temperature T c of La(Fe 1−x Ni x ) 11.5 Si 1.5 (x = 0, 0.01, 0.02, 0.03) compounds increase monotonously from 195 K to 219 K when Ni content x varies from 0 to 0.03. Highlights: ► We substituted Fe by new element Ni in La(Fe 1−x Ni x ) 11.5 Si 1.5 compounds. ► The microstructure evolution, magnetic phase transition and Curie temperature of La(Fe 1−x Ni x ) 11.5 Si 1.5 compounds were investigated. ► The small substitution of Ni for Fe in La(Fe 1−x Ni x ) 11.5 Si 1.5 compounds enhances the formation of 1:13 phase and helps the elimination of impurity phase significantly. ► The Curie temperature T C of La(Fe 1−x Ni x ) 11.5 Si 1.5 compounds increase monotonously from 195 K to 219 K when x varies from 0 to 0.03. - Abstract: The influence of Ni substitution on the microstructure evolution and magnetic phase transition has been investigated in La(Fe 1−x Ni x ) 11.5 Si 1.5 (x = 0, 0.01, 0.02, 0.03) compounds. Results show that partial substitution of Ni for Fe in La(Fe 1−x Ni x ) 11.5 Si 1.5 (x = 0, 0.01, 0.02, 0.03) alloys promotes fining of the as-cast microstructure. Besides, the formation of 1:13 phase and the elimination of impurity phases is facilitated significantly when annealed at 1373 K for 5 days. Large amounts of inhomogeneities are present in the annealed LaFe 11.5 Si 1.5 alloy. While almost single 1:13 phase is obtained in La(Fe 1−x Ni x ) 11.5 Si 1.5 (x = 0.02, 0.03) alloys. Moreover, the Curie temperature T C of La(Fe 1−x Ni x ) 11.5 Si 1.5 (x = 0, 0.01, 0.02, 0.03) compounds increase monotonously from 195 K to 219 K when Ni content x varies from 0 to 0.03.

Growth of C60 thin films on Al2O3/NiAl(100) at early stages

Science.gov (United States)

Hsu, S.-C.; Liao, C.-H.; Hung, T.-C.; Wu, Y.-C.; Lai, Y.-L.; Hsu, Y.-J.; Luo, M.-F.

2018-03-01

The growth of thin films of C60 on Al2O3/NiAl(100) at the earliest stage was studied with scanning tunneling microscopy and synchrotron-based photoelectron spectroscopy under ultrahigh-vacuum conditions. C60 molecules, deposited from the vapor onto an ordered thin film of Al2O3/NiAl(100) at 300 K, nucleated into nanoscale rectangular islands, with their longer sides parallel to direction either [010] or [001] of NiAl. The particular island shape resulted because C60 diffused rapidly, and adsorbed and nucleated preferentially on the protrusion stripes of the crystalline Al2O3 surface. The monolayer C60 film exhibited linear protrusions of height 1-3 Å, due to either the structure of the underlying Al2O3 or the lattice mismatch at the boundaries of the coalescing C60 islands; such protrusions governed also the growth of the second layer. The second layer of the C60 film grew only for a C60 coverage >0.60 ML, implying a layer-by-layer growth mode, and also ripened in rectangular shapes. The thin film of C60 was thermally stable up to 400 K; above 500 K, the C60 islands dissociated and most C60 desorbed.

Photochemical deposition of NiCoO x thin films from Ni/Co heteronuclear triketonate complexes

International Nuclear Information System (INIS)

Buono-Core, G.E.; Tejos, M.; Cabello, G.; Guzman, N.; Hill, R.H.

2006-01-01

UV light irradiation of thin films of a polyketonate Ni/Co heteronuclear complex, NiCo(DBA) 2 [DBA, dibenzoylacetone)], spin coated on Si(1 0 0) substrates produced NiCoO x mixed oxides as amorphous films. On annealing at 600 deg. C under air, the mixed oxide film decomposed to NiO and CoO as indicated by XRD measurements. The morphology of the as-deposited films was examined by AFM analysis showing a smooth surface with low rms roughness values. The ratio of Ni/Co (1.08) present in the film reflects the stoichiometry in the starting compound within the experimental error, as shown by XPS analysis. The large amount of carbon (20.8%) detected on the surface of the film may be due to the presence of phenyl rings in the precursor complex

A potential method using Ge{iPrNC[N(SiMe_3)_2]NiPr}{sub 2}, (Et{sub 3}Si){sub 2}Te and anhydrous hydrazine for germanium tellurides

Energy Technology Data Exchange (ETDEWEB)

Du, Liyong; Du, Shulei; Ding, Yuqiang [School of Chemical and Material Engineering, Jiangnan University, Wuxi (China)

2017-12-29

A germanium(II)-guanidine derivative of formula Ge{iPrNC[N(SiMe_3)_2]NiPr}{sub 2} (1) was synthesized and characterized by {sup 1}H NMR, {sup 13}C NMR, elemental analysis, and X-ray diffraction method. Thermal property was also studied to identify its thermal stability and volatility. More importantly, compound 1 was synthesized to develop a new method for germanium tellurides, where anhydrous hydrazine was introduced to prompt the activity of germanium(II) guanidines (or derivatives) towards (Et{sub 3}Si){sub 2}Te. Solution reaction of compound 1, (Et{sub 3}Si){sub 2}Te, and anhydrous hydrazine was investigated to pre-identify the feasibility of this combination for ALD process. The EDS data of the black precipitate from this reaction verified the potential of this method to manufacture germanium tellurides. (copyright 2017 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

Reversible Changes in Resistance of Perovskite Nickelate NdNiO3 Thin Films Induced by Fluorine Substitution.

Science.gov (United States)

Onozuka, Tomoya; Chikamatsu, Akira; Katayama, Tsukasa; Hirose, Yasushi; Harayama, Isao; Sekiba, Daiichiro; Ikenaga, Eiji; Minohara, Makoto; Kumigashira, Hiroshi; Hasegawa, Tetsuya

2017-03-29

Perovskite nickel oxides are of fundamental as well as technological interest because they show large resistance modulation associated with phase transition as a function of the temperature and chemical composition. Here, the effects of fluorine doping in perovskite nickelate NdNiO 3 epitaxial thin films are investigated through a low-temperature reaction with polyvinylidene fluoride as the fluorine source. The fluorine content in the fluorinated NdNiO 3-x F x films is controlled with precision by varying the reaction time. The fully fluorinated film (x ≈ 1) is highly insulating and has a bandgap of 2.1 eV, in contrast to NdNiO 3 , which exhibits metallic transport properties. Hard X-ray photoelectron and soft X-ray absorption spectroscopies reveal the suppression of the density of states at the Fermi level as well as the reduction of nickel ions (valence state changes from +3 to +2) after fluorination, suggesting that the strong Coulombic repulsion in the Ni 3d orbitals associated with the fluorine substitution drives the metal-to-insulator transition. In addition, the resistivity of the fluorinated films recovers to the original value for NdNiO 3 after annealing in an oxygen atmosphere. By application of the reversible fluorination process to transition-metal oxides, the search for resistance-switching materials could be accelerated.

Pauli paramagnetic effects on vortices in superconducting TmNi2B2C

DEFF Research Database (Denmark)

DeBeer-Schmitt, L.; Eskildsen, Morten Ring; Ichioka, M.

2007-01-01

The magnetic field distribution around the vortices in TmNi2B2C in the paramagnetic phase was studied experimentally as well as theoretically. The vortex form factor, measured by small-angle neutron scattering, is found to be field independent up to 0.6H(c2) followed by a sharp decrease at higher...

Pitting Corrosion of Ni3(Si,Ti+4Al Intermetallic Compound at Various Chloride Concentrations

Directory of Open Access Journals (Sweden)

Gadang Priyotomo

2014-04-01

Full Text Available The pitting corrosion of Ni3(Si,Ti with 4 at% Al consisting of two regions of a Ni3(Si,Ti single-phase of L12 structure and two phases of L12 and fcc Niss was investigated as function of chloride concentrations by using electrochemical method, scanning electron microscope and energy dispersive X-Ray spectroscopy in neutral sodium chloride solutions at 293 K.  In addition, the pitting corrosion of Ni3(Si,Ti and  type C276 alloy were also studied under the same experimental condition for comparison.  The pitting potential obtained for the Ni3(Si,Ti with 4 at%Al decreased with increasing chloride concentration.  The specific pitting potential and pitting potential of Ni3(Si,Ti with 4at%, Ni3(Si,Ti and C276 were the lowest, the moderate and the highest, respectively, which means that the pitting corrosion resistance of Ni3(Si,Ti was higher than Ni3(Si,Ti with 4at% Al, but lower than that of C276.  A critical chloride concentration of Ni3(Si,Ti with 4at% Al was found to be lower than that of Ni3(Si,Ti.  The Pitting corrosion of Ni3(Si,Ti with 4at% Al occurred in the two phase mixture (L12 + Niss.

Thermodynamic investigations of the Mn-Ni-C-N quarternary alloys by solid-state galvanic cell technique

International Nuclear Information System (INIS)

Teng Lidong; Aune, Ragnhild; Seetharaman, Seshadri

2005-01-01

In view of the important applications of carbides and nitrides of transition metals in the hard materials industries, the thermodynamic activities of manganese in Mn-Ni-C-N alloys have been studied by solid-state galvanic cell technique with CaF 2 as the solid electrolyte. The phase compositions and microstructure of various alloys have been analyzed by X-ray diffraction (XRD) and scanning electron microscopy (SEM). Nitrogen was introduced into the alloy by equilibrating with N 2 gas. It was established during the experiments that the solubility of nitrogen in the alloys was affected by the carbon content. A (Mn,Ni) 4 (N,C) nitride was formed during the nitriding procedure in the alloys. The electromotive force (EMF) measurements were carried out in the temperature range 940-1127 K in order to determine the activities of Mn in the alloys. The activities of manganese were calculated and compared with those of the corresponding Mn-Ni-C ternary alloys

Oxidation behaviors of the TiNi/Ti_2Ni matrix composite coatings with different contents of TaC addition fabricated on Ti6Al4V by laser cladding

International Nuclear Information System (INIS)

Lv, Y.H.; Li, J.; Tao, Y.F.; Hu, L.F.

2016-01-01

The TiNi/Ti_2Ni matrix composite coatings were fabricated on Ti6Al4V by laser cladding the mixtures of NiCrBSi and different contents of TaC (0 wt%, 5 wt%, 15 wt%, 30 wt% and 40 wt%). Scanning electron microscopy (SEM), energy dispersive spectrometry (EDS) and X-ray diffractometry (XRD) were used to examine the microstructures of the coatings. Oxidation behaviors of these coatings were also investigated at 800 °C for 50 h in air. The results showed that the coating without TaC addition was mainly composed of TiNi/Ti_2Ni as the matrix and TiC/TiB_2/TiB as the reinforcement. TaC was dissolved completely and precipitated again during laser cladding. Ta and C from the added TaC mainly existed as the solute atoms in the solid solutions of TiC, TiB_2 and TiB in the coatings with TaC addition. The addition of TaC refined the microstructures of the coatings. In the oxidation test, the oxidation process was divided into the violent oxidation stage and the slow oxidation stage. The oxidation rates of the substrate and the coatings with different contents of TaC (0, 5, 15, 30, 40 wt%) were 0.644, 0.287, 0.173, 0.161, 0.223 and 0.072 mg cm"−"2 h"−"1 in the first stage, 0.884, 0.215, 0.136, 0.126, 0.108 and 0.040 mg"2 cm"−"4 h"−"1 in the second stage, respectively. The weight gain of these samples were 6.70, 3.30, 2.86, 2.64, 2.41 and 1.69 mg cm"−"2, respectively after the whole oxidation test. The oxidation film formed on the surface of the coating without TaC addition mainly consisted of TiO_2, Al_2O_3, and a small amount of NiO, Cr_2O_3 and SiO_2. Moreover, Ta_2O_5 was also formed on the surfaces of these coatings with different contents of TaC. The oxides formed during the oxidation test were supposed to be responsible for the improvement in oxidation resistance of these coatings. - Highlights: • The composite coatings with TaC addition were fabricated on Ti6Al4V by laser cladding. • Effect of TaC addition on microstructural evolution of the coatings was

A first-principles study of B2 NiAl alloyed with rare earth elements Pr, Pm, Sm, and Eu

Institute of Scientific and Technical Information of China (English)

He Jun-Qi; Wang You; Yan Mu-Fu; Pan Zhao-Yi; Guo Li-Xin

2013-01-01

The structural,elastic,and electronic properties of NiAl alloyed with rare earth elements Pr,Pm,Sm,and Eu are investigated by using density functional theory (DFT).The study suggests that Pr,Pm,Sm,and Eu all tend to be substituted for an Al site.Ni8Al7Pm possesses the largest ductility.Only the hardness and ductility of Ni8Al7Eu are enhanced simultaneously.The covalency strength of the Ni-Al bond in Ni8Al7Pm is higher than that in Ni8Al7Eu.The covalency strength of an Al-Al bond and that of a Ni-Ni bond in Ni8Al7Eu are higher than that in Ni8Al7Pm.The Ni-Pm bond and the Ni-Eu bond are covalent,and the covalency strength of the Ni-Pm bond is greater.The Al-Pm bond and the Al-Eu bond show great covalency strength and ionicity,respectively.

Corrosion Behavior of Ni3(Si,Ti + 2Mo in Hydrochloric Acid Solution

Directory of Open Access Journals (Sweden)

Gadang Priyotomo

2013-10-01

Full Text Available The corrosion behavior of Ni3(Si,Ti + 2Mo intermetallic compound (L12 and (L12 + Niss mixture region has been investigated using an immersion test, polarization method and surface analytical method (scanning electron microscope and energy-dispersive X-Ray spectrometry in 0.5 kmol/m3 hydrochloric acid (HCl solution at 303 K.  In addition, the results obtained were compared to those of the L12 single-phase Ni3(Si,Ti intermetallic compound and C 276 alloy.  It was found that Ni3(Si,Ti + 2Mo had the preferential dissolution of L12 with a lower Mo concentration compared to (L12 + Niss mixture region.  From the immersion test and polarization curves, Ni3(Si,Ti + 2Mo and C276 showed the lowest corrosion resistance and the highest corrosion resistance in the solution, respectively.  From this work, It implied that unlike C276, Ni3(Si,Ti +2Mo intermetallic compound was difficult to form a stable passive film in HCl solution as well as Ni3(Si,Ti in the same solution.

Validation of a method for the determination of 14C and 63Ni in samples of concrete

International Nuclear Information System (INIS)

Rosskopfova, Olga; Galambos, Michal; Pupak, Matus

2009-01-01

For the determination of 14 C, the concrete sample was distilled in inert atmosphere and the released 14 CO 2 was trapped in a scintillation vial with Carbo-Sorb E. Permafluor E was added and the well mixed sample was kept in the dark for 24 h, after which the preparation was measured on a liquid scintillation spectrometer. For the determination of 63 Ni the sample was ignited at 550 deg C overnight and subjected to acid leaching. Nickel was then separated by a procedure which included separation from Fe by precipitation with NH 4 OH and precipitation of Ni with dimethylglyoxime and purification by extraction chromatography on Ni Resin; 63 Ni was determined by liquid scintillation spectrophotometry of the beta radiation. The participation in the interlaboratory comparison exercise gave evidence of the reliability and quality of the results achieved by the laboratory. (P.A.)

Investigation of ethanol electrooxidation on a Pt-Ru-Ni/C catalyst for a direct ethanol fuel cell

Energy Technology Data Exchange (ETDEWEB)

Wang, Zhen-Bo; Yin, Ge-Ping; Zhang, Jian; Sun, Ying-Chao; Shi, Peng-Fei [Department of Applied Chemistry, Harbin Institute of Technology, Harbin (China 150001)

2006-09-29

This research is aimed to improve the utilization and activity of anodic alloy catalysts and thus to lower the contents of noble metals and the catalyst loading on anodes for ethanol electrooxidation. The DEFC anodic catalysts, Pt-Ru-Ni/C and Pt-Ru/C, were prepared by a chemical reduction method. Their performances were tested by using a glassy carbon working electrode and cyclic voltammetric curves, chronoamperometric curves and half cell measurement in a solution of 0.5molL{sup -1} CH{sub 3}CH{sub 2}OH and 0.5molL{sup -1} H{sub 2}SO{sub 4}. The composition of the Pt-Ru-Ni and Pt-Ru surface particles were determined by EDAX analysis. The particle size and lattice parameter of the catalysts were determined by means of X-ray diffraction (XRD). XRD analysis showed that both of the catalysts exhibited face centered cubic structures and had smaller lattice parameters than a Pt-alone catalyst. Their particle sizes were small, about 4.5nm. No significant differences in the ethanol electrooxidation on both electrodes were found using cyclic voltammetry, especially regarding the onset potential for ethanol electrooxidation. The electrochemically active specific areas of the Pt-Ru-Ni/C and Pt-Ru/C catalysts were almost the same. But, the catalytic activity of the Pt-Ru-Ni/C catalyst was higher for ethanol electrooxidation than that of the Pt-Ru/C catalyst. Their tolerance to CO formed as one of the intermediates of ethanol electrooxidation, was better than that of the Pt-Ru/C catalyst. (author)

The Effect of Milling Time on the Microstructural Characteristics and Strengthening Mechanisms of NiMo-SiC Alloys Prepared via Powder Metallurgy

Science.gov (United States)

Yang, Chao; Muránsky, Ondrej; Zhu, Hanliang; Thorogood, Gordon J.; Avdeev, Maxim; Huang, Hefei; Zhou, Xingtai

2017-01-01

A new generation of alloys, which rely on a combination of various strengthening mechanisms, has been developed for application in molten salt nuclear reactors. In the current study, a battery of dispersion and precipitation-strengthened (DPS) NiMo-based alloys containing varying amounts of SiC (0.5–2.5 wt %) were prepared from Ni-Mo-SiC powder mixture via a mechanical alloying (MA) route followed by spark plasma sintering (SPS) and rapid cooling. Neutron Powder Diffraction (NPD), Electron Back Scattering Diffraction (EBSD), and Transmission Electron Microscopy (TEM) were employed in the characterization of the microstructural properties of these in-house prepared NiMo-SiC DPS alloys. The study showed that uniformly-dispersed SiC particles provide dispersion strengthening, the precipitation of nano-scale Ni3Si particles provides precipitation strengthening, and the solid-solution of Mo in the Ni matrix provides solid-solution strengthening. It was further shown that the milling time has significant effects on the microstructural characteristics of these alloys. Increased milling time seems to limit the grain growth of the NiMo matrix by producing well-dispersed Mo2C particles during sintering. The amount of grain boundaries greatly increases the Hall–Petch strengthening, resulting in significantly higher strength in the case of 48-h-milled NiMo-SiC DPS alloys compared with the 8-h-milled alloys. However, it was also shown that the total elongation is considerably reduced in the 48-h-milled NiMo-SiC DPS alloy due to high porosity. The porosity is a result of cold welding of the powder mixture during the extended milling process. PMID:28772747

The Effect of Milling Time on the Microstructural Characteristics and Strengthening Mechanisms of NiMo-SiC Alloys Prepared via Powder Metallurgy

Directory of Open Access Journals (Sweden)

Chao Yang

2017-04-01

Full Text Available A new generation of alloys, which rely on a combination of various strengthening mechanisms, has been developed for application in molten salt nuclear reactors. In the current study, a battery of dispersion and precipitation-strengthened (DPS NiMo-based alloys containing varying amounts of SiC (0.5–2.5 wt % were prepared from Ni-Mo-SiC powder mixture via a mechanical alloying (MA route followed by spark plasma sintering (SPS and rapid cooling. Neutron Powder Diffraction (NPD, Electron Back Scattering Diffraction (EBSD, and Transmission Electron Microscopy (TEM were employed in the characterization of the microstructural properties of these in-house prepared NiMo-SiC DPS alloys. The study showed that uniformly-dispersed SiC particles provide dispersion strengthening, the precipitation of nano-scale Ni3Si particles provides precipitation strengthening, and the solid-solution of Mo in the Ni matrix provides solid-solution strengthening. It was further shown that the milling time has significant effects on the microstructural characteristics of these alloys. Increased milling time seems to limit the grain growth of the NiMo matrix by producing well-dispersed Mo2C particles during sintering. The amount of grain boundaries greatly increases the Hall–Petch strengthening, resulting in significantly higher strength in the case of 48-h-milled NiMo-SiC DPS alloys compared with the 8-h-milled alloys. However, it was also shown that the total elongation is considerably reduced in the 48-h-milled NiMo-SiC DPS alloy due to high porosity. The porosity is a result of cold welding of the powder mixture during the extended milling process.

Validation of a method for the determination of 14C and 63Ni activity in concrete matrices

International Nuclear Information System (INIS)

Rosskopfova, Olga; Galambos, Michal; Pupak, Matus

2010-01-01

Simple and reliable methods were developed for the determination of 14 C and 63 Ni activity in concrete by using a low-background liquid scintillation counter. Direct CO 2 absorption was used in the determination of 14 C whereas extraction chromatography on a Nickel Resin column (Eichrom) served to determine 63 Ni. The methods were validated by engagement in the Environmental Radioactivity Proficiency Test Exercise 2008, complying with ISO/IEC 17025:2005

The equiatomic intermetallics REPtCd (RE = La, Ce, Pr, Nd, Eu) and magnetic properties of CeAuCd

Energy Technology Data Exchange (ETDEWEB)

Johnscher, Michael; Niehaus, Oliver; Poettgen, Rainer [Muenster Univ. (Germany). Inst. fuer Anorganische und Analytische Chemie; Tappe, Frank [Hochschule Hamm-Lippstadt, Hamm (Germany)

2015-06-01

The cadmium intermetallics REPtCd (RE = La, Ce, Pr, Nd, Eu) and CeAuCd were synthesized by induction-melting of the elements in sealed niobium ampoules followed by annealing in muffle furnaces. The samples were characterized by powder X-ray diffraction. The structures of CePtCd (ZrNiAl type, P anti 62m, a = 763.8(6), c = 409.1(4) pm, wR2 = 0.0195, 298 F{sup 2} values, 14 variables) and EuPtCd (TiNiSi type, Pnma, a = 741.3(2), b = 436.4(1), c = 858.0(4) pm, wR2 = 0.0385, 440 F{sup 2} values, 20 variables) were refined from single-crystal data. The REPtCd structures exhibit three-dimensional networks of corner- and edge-sharing Cd rate at Pt{sub 2/6}Pt{sub 2/3} and Cd rate at Pt{sub 4/4} tetrahedra, which leave cages for the rare earth atoms. Temperature-dependent magnetic susceptibility data of CeAuCd reveal a paramagnetic to antiferromagnetic phase transition at T{sub N} = 3.7(5) K.

The equiatomic intermetallics REPtCd (RE = La, Ce, Pr, Nd, Eu) and magnetic properties of CeAuCd

International Nuclear Information System (INIS)

Johnscher, Michael; Niehaus, Oliver; Poettgen, Rainer

2015-01-01

The cadmium intermetallics REPtCd (RE = La, Ce, Pr, Nd, Eu) and CeAuCd were synthesized by induction-melting of the elements in sealed niobium ampoules followed by annealing in muffle furnaces. The samples were characterized by powder X-ray diffraction. The structures of CePtCd (ZrNiAl type, P anti 62m, a = 763.8(6), c = 409.1(4) pm, wR2 = 0.0195, 298 F 2 values, 14 variables) and EuPtCd (TiNiSi type, Pnma, a = 741.3(2), b = 436.4(1), c = 858.0(4) pm, wR2 = 0.0385, 440 F 2 values, 20 variables) were refined from single-crystal data. The REPtCd structures exhibit three-dimensional networks of corner- and edge-sharing Cd rate at Pt 2/6 Pt 2/3 and Cd rate at Pt 4/4 tetrahedra, which leave cages for the rare earth atoms. Temperature-dependent magnetic susceptibility data of CeAuCd reveal a paramagnetic to antiferromagnetic phase transition at T N = 3.7(5) K.

Large magnetocaloric effect of GdNiAl{sub 2} compound

Energy Technology Data Exchange (ETDEWEB)

Dembele, S.N.; Ma, Z.; Shang, Y.F. [School of Physical Electronics, University of Electronic Science and Technology of China, Chengdu 610054 (China); Fu, H., E-mail: fuhao@uestc.edu.cn [School of Physical Electronics, University of Electronic Science and Technology of China, Chengdu 610054 (China); Balfour, E.A. [School of Physical Electronics, University of Electronic Science and Technology of China, Chengdu 610054 (China); Hadimani, R.L.; Jiles, D.C. [Department of Electrical and Computer Engineering, Iowa State University, Ames, IA 50011 (United States); Ames Laboratory, US Department of Energy, Ames, IA 50011 (United States); Teng, B.H.; Luo, Y. [School of Physical Electronics, University of Electronic Science and Technology of China, Chengdu 610054 (China)

2015-10-01

This paper presents the structure, magnetic properties, and magnetocaloric effect of the polycrystalline compound GdNiAl{sub 2}. Powder X-ray diffraction (XRD) measurement and Rietveld refinement revealed that GdNiAl{sub 2} alloy is CuMgAl{sub 2}-type phase structure with about 1 wt% GdNi{sub 2}Al{sub 3} secondary phase. Magnetic measurements suggest that the compound is ferromagnetic and undergoes a second-order phase transition near 28 K. The maximum value of magnetic entropy change reaches 16.0 J/kg K for an applied magnetic field change of 0–50 kOe and the relative cooling power was 6.4×10{sup 2} J/kg. It is a promising candidate as a magnetocaloric material working near liquid hydrogen temperature (~20 K) exhibiting large relative cooling power. - Highlights: • Preferred orientation with axis of [010] was found in the GdNiAl{sub 2} compound. • The ΔS{sub Mmax} and the RCP are 16.0 J/kg K and 640 J/kg, respectively, for ΔH=50 kOe. • Relative low rare earth content in GdNiAl{sub 2} comparing with other candidates.

pH-Dependent isotope exchange and hydrogenation catalysed by water-soluble NiRu complexes as functional models for [NiFe]hydrogenases

OpenAIRE

Kure, Bunsho; Matsumoto, Takahiro; Ichikawa, Koji; Fukuzumi, Shunichi; Higuchi, Yoshiki; Yagi, Tatsuhiko; Ogo, Seiji

2008-01-01

The pH-dependent hydrogen isotope exchange reaction between gaseous isotopes and medium isotopes and hydrogenation of the carbonyl compounds have been investigated with water-soluble bis(mu-thiolate)(mu-hydride)NiRu complexes, Ni(II)(mu-SR)(2)(mu-H)Ru(II) {(mu-SR)(2) = N,N'-dimethyl-N,N'-bis(2-mercaptoethyl)-1,3-propanediamine}, as functional models for [NiFe]hydrogenases. In acidic media (at pH 4-6), the mu-H ligand of the Ni(II)(mu-SR)(2)(mu-H)Ru(II) complexes has H(+) properties, and the c...

Neutron diffraction studies on structural and magnetic properties of RE2NiGe3 (RE=La, Ce)

International Nuclear Information System (INIS)

Kalsi, Deepti; Rayaprol, S.; Siruguri, V.; Peter, Sebastian C.

2014-01-01

We report the crystallographic properties of RE 2 NiGe 3 (RE=La, Ce) synthesized by arc melting. Rietveld refinement on the powder neutron diffraction (ND) data suggest both compounds are isostructural and crystallize in the non-centrosymmetric Er 2 RhSi 3 type structure having hexagonal space group P6 ¯ 2c. In the crystal structure of RE 2 NiGe 3 , two dimensional arrangements of nickel and germanium atoms lead to the formation of hexagonal layers with rare earth atoms sandwiched between them. Magnetic susceptibility measurements performed in low fields exhibit antiferromagnetic ordering in cerium compound around (T o =) 3.2 K. Neutron diffraction measurements at 2.8 K (i.e., at Tcompounds La 2 NiGe 3 and Ce 2 NiGe 3 crystallize in the Er 2 RhSi 3 type. Magnetic susceptibility show antiferromagnetic ordering for Ce 2 NiGe 3 at 3.2 K and neutron diffraction confirms the absence of long range ordering. - Highlights: RE 2 NiGe 3 (RE=La, Ce) crystallize in the ordered superstructure of the AlB 2 type. Magnetic susceptibility measurements exhibit antiferromagnetic ordering in Ce 2 NiGe 3 . Structure and magnetism of RE 2 NiGe 3 (RE=La, Ce) are studied by neutron diffraction

The ''C'' family of Ni-Cr-Mo allloys' partnership with the chemical process industry: the last 70 years

International Nuclear Information System (INIS)

Agarwal, D.C.; Herda, W.R.

1997-01-01

The ''C'' family of alloys, the original being Hastelloy trademark alloy C (1930's) was an innovative optimization of Ni-Cr alloys having good resistance to oxidizing corrosive media and Ni-Mo alloys with superior resistance to reducing corrosive media. This combination resulted in the most versatile corrosion resistant alloy in the ''Ni-Cr-Mo'' alloy family, with exceptional corrosion resistance in a wide variety of severe corrosive environments typically encountered in CPI and other industries. The alloy also exhibited excellent resistance to pitting and crevice corrosion attack in low pH, high chloride oxidizing environments and had virtual immunity to chloride stress corrosion cracking. These properties allowed this alloy to serve the industrial needs for many years, although it had some limitations. The decades of the 1960's (alloy C-276), 1970's (alloy C-4), 1980's (alloy C-22 and 622) and 1990's (alloy 59, alloy 686 and alloy C-2000) saw newer alloy developments with improvements in corrosion resistance, which not only overcame the limitations of alloy C, but further expanded the horizons of applications as the needs of the CPI became more critical, severe and demanding. Today the originally alloy ''C'' of the 1930's is practically obsolete except for some usage in form of castings. This paper presents a chronology of the various corrosion resistant alloy developments during this century, with special emphasis on the last 70 years evolution in the ''C'' family of Ni-Cr-Mo alloys and their applications. (orig.)

The Al-rich region of the Al-Mn-Ni alloy system. Part II. Phase equilibria at 620-1000 oC

International Nuclear Information System (INIS)

Balanetskyy, S.; Meisterernst, G.; Grushko, B.; Feuerbacher, M.

2011-01-01

Research highlights: → Phase equilibria in the Al-rich region of the Al-Mn-Ni alloy system were studied at 1000, 950, 850, 750, 700, 645 and 620 deg. C by means of SEM, TEM, powder XRD and DTA. → Three ternary thermodynamically stable intermetallics, the φ-phase (Al 5 Co 2 -type, hP26, P63/mmc; a = 0.76632(16), c = 0.78296(15) nm), the κ-phase (κ-Al 14.4 Cr 3.4 Ni l.1 -type, hP227, P63/m; a = 1.7625(10), c = 1.2516(10) nm), and the O-phase (O-Al 77 Cr 14 Pd 9 -type, Pmmn, oP650,: a = 2.3316(16), b = 1.2424(15), c = 3.2648(14) nm), as well as three ternary metastable phases, the decagonal D 3 -phase with periodicity about 1.25 nm, the Al 9 (Mn,Ni) 2 -phase (Al 9 Co 2 -type, P1121/a, mP22; a = 0.8585(16), b = 0.6269(9), c = 0.6205(11) nm, β = 95.34(10) o ) and the O 1 -phase (basecentered orthorhombic, a ∼ 23.8, b ∼ 12.4, c ∼ 32.2 nm) were revealed. → The existence of a thermodynamically stable R-phase of stoichiometry Al 60 Mn 11 Ni 4 , reported earlier in literature, was not confirmed in the present study. - Abstract: Phase equilibria in the Al-rich region of the Al-Mn-Ni alloy system were studied at 1000, 950, 850, 750, 700, 645 and 620 o C. Three ternary thermodynamically stable intermetallics, the φ-phase (Al 5 Co 2 -type, hP26, P6 3 /mmc; a = 0.76632(16), c = 0.78296(15) nm), the κ-phase (κ-Al 14.4 Cr 3.4 Ni l.1 -type, hP227, P6 3 /m; a = 1.7625(10), c = 1.2516(10) nm), and the O-phase (O-Al 77 Cr 14 Pd 9 -type, Pmmn, oP650,: a = 2.3316(16), b = 1.2424(15), c = 3.2648(14) nm), as well as three ternary metastable phases, the decagonal D 3 -phase with periodicity about 1.25 nm, the Al 9 (Mn,Ni) 2 -phase (Al 9 Co 2 -type, P112 1 /a, mP22; a = 0.8585(16), b = 0.6269(9), c = 0.6205(11) nm, β = 95.34(10) o ) and the O 1 -phase (base-centered orthorhombic, a ∼ 23.8, b ∼ 12.4, c ∼ 32.2 nm) were revealed. Their physicochemical behaviour in the Al-Mn-Ni alloy system was studied.

Direct selenylation of mixed Ni/Fe metal-organic frameworks to NiFe-Se/C nanorods for overall water splitting

Science.gov (United States)

Xu, Bo; Yang, He; Yuan, Lincheng; Sun, Yiqiang; Chen, Zhiming; Li, Cuncheng

2017-10-01

Development of low-cost, highly active bifunctional catalyst for efficient overall water splitting based on earth-abundant metals is still a great challenging task. In this work, we report a NiFe-Se/C composite nanorod as efficient non-precious-metal electrochemical catalyst derived from direct selenylation of a mixed Ni/Fe metal-organic framework. The as-obtained catalyst requires low overpotential to drive 10 mA cm-2 for HER (160 mV) and OER (240 mV) in 1.0 M KOH, respectively, and its catalytic activity is maintained for at least 20 h. Moreover, water electrolysis using this catalyst achieves high water splitting current density of 10 mA cm-2 at cell voltage of 1.68 V.

Equiatomic indides REIrIn (RE=La, Pr, Nd, Er-Yb). Crystal and electronic structure

Energy Technology Data Exchange (ETDEWEB)

Zaremba, Nazar [Ivan Franko National Univ. of Lviv (Ukraine). Dept. of Inorganic Chemistry; Technische Univ. Muenchen, Garching (Germany). Fakultaet fuer Chemie; Muts, Ihor; Zaremba, Vasyl [Ivan Franko National Univ. of Lviv (Ukraine). Dept. of Inorganic Chemistry; Hlukhyy, Viktor [Technische Univ. Muenchen, Garching (Germany). Fakultaet fuer Chemie; Stein, Sebastian; Rodewald, Ute C.; Poettgen, Rainer [Muenster Univ. (Germany). Inst. fuer Anorganische und Analytische Chemie; Pavlyuk, Volodymyr [Ivan Franko National Univ. of Lviv (Ukraine). Dept. of Inorganic Chemistry; Czestochowa Jan Dlugosz Univ., Czestochowa (Poland). Inst. of Chemistry, Environmental Protection and Biotechnology

2017-10-01

The equiatomic rare earth iridium indides REIrIn (RE=La, Pr, Nd, Er-Yb) were synthesized by reaction of the elements in induction or muffle furnaces and were characterized through X-ray powder patterns. The structures of LaIr{sub 0.86}In{sub 1.14}, PrIr{sub 0.89}In{sub 1.11}, NdIr{sub 0.94}In{sub 1.06}, ErIrIn (all ZrNiAl type, P anti 62m), and YbIrIn (TiNiSi type, Pnma) were refined from single crystal X-ray diffractometer data. Refinements of the occupancy parameters revealed small degrees of solid solutions with indium substitution on the iridium sites. Chemical bonding analyses and electronic structure calculations indicate the dominance of metallic bonding in addition to partial ionic interactions between the cations and polyanions, as well as covalent contributions between the indium and iridium atoms.

The Ni3Al and NiAl alloys: a class of intermetallics which can replace the Ni-base superalloys for the aerospace high temperature structural applications

International Nuclear Information System (INIS)

Lucaci, M.; Vidu, C.D.; Vasile, E.

2001-01-01

The paper presents the results obtained in synthesizing Ni-base refractory intermetallics from elemental powder mixes. In view of this, four mixes were made for the Ni 3 Al intermetallics and five mixes for the NiAl ones. The compound synthesis was made at T = 660 o C under vacuum by the SHS method, in the thermo-explosion mode. The variable parameters were the compacting pressure and the aluminum amount in the mixes. The obtained materials were then characterized by the microstructure and by the physical properties. The product synthesis degree was followed as well as their influence on the types of microstructures obtained. The reaction products were evidenced by x-ray diffraction and by quantitative chemical microanalysis. The obtained results revealed the formation of the Ni 3 Al compound having a primitive cubic crystal lattice with a 0 = 3,564 Aa and the formation of the NiAl compound, of a bcc lattice having a 0 = 2,86 Aa. Those obtained prove the ample influences of the powder homogeneity degree and of the powder purity on the possibility to produce an adequate synthesis, as well as the influence of the amount liquid appeared in the system on the synthesis degree, on the reaction rate and on the porosity of materials obtained. (author)

Effect of ion plating TiN on the oxidation of sputtered NiCrAlY-coated Ti3Al-Nb in air at 850-950 C

International Nuclear Information System (INIS)

Rizzo, F.C.; Zeng, C.; Chinese Academy of Sciences, Shenyang; Wu, W.

1998-01-01

A single sputtered NiCrAlY coating and a complex coating of inner ion-plated TiN and outer sputtered NiCrAlY were prepared on the intermetallic compound Ti 3 Al-Nb. Their oxidation behavior was examined at 850, 900, and 950 C in air by thermal gravimetry combined with XRD, SEM, and EDAX. The results showed that Ti 3 Al-Nb followed approximately parabolic oxidation, forming an outer thin Al 2 O 3 -rich scale and an inner TiO 2 -rich layer doped with Nb at the three temperatures. The TiO 2 -rich layer doped with Nb dominated the oxidation reaction. The single NiCrAlY coating did not follow parabolic oxidation exactly at 850 and 950 C, but oxidized approximately in a parabolic manner, because the instantaneous parabolic constants changed slightly with time. Besides the Al 2 O 3 scale, TiO 2 formed from the coating surface at the coating-substrate interface. The deterioration of the coating accelerated with increasing temperature. The NiCrAlY-TiN coating showed two-stage parabolic oxidation at 850 and 900 C, and an approximate parabolic oxidation at 950 C. The TiN layer was effective as a barrier to inhibit coating-alloy interdiffusion

Changes of structure and properties of cast steels GX10NiCrNb32-20 and GX10NiCrNb3-25 after long-term tempering at 600-1000 C

International Nuclear Information System (INIS)

Gommans, R.; Schrijen, H.; Sundermann, J.; Steinkusch, W.; Hering, W.

2001-01-01

Low-alloy cast steels of type GX 10NiCrNb 32.20 are commonly used for the outlet section of reformer and cracker tubes for the temperature range of 600-1000 C. There was a lack of data on the ductility of the 25%Cr alloyed cast steel GX10NiCrNb 35.25 at room temperature after tempering, which was investigated in a joint project of Pose-Marre and DSM. Mechanical tests were carried out at room temperature and at elevated temperatures. Apart from light microscopy, also SEM/EDX, SAM and TEM analyses were carried out. The 25% alloy has lower ductility than the 20% alloy, owing primarily to the more pronounced development of M 6 C carbide from primary NbC carbide, which takes up Ni and Si during tempering. The microstructure and composition of the M 6 C carbide wre not fully clarified. Information is presented on the potential application of low-carbon materials of the type GX10NiCrNb35.25 [de

Gd-Ni-Si system

International Nuclear Information System (INIS)

Bodak, O.I.; Shvets, A.F.

1983-01-01

By X-ray phase analysis method isothermal cross section of phase diagram of the Gd-Ni-Si system at 870 K is studied. The existence of nine previously known compounds (GdNisub(6.72)Sisub(6.28), GdNi 10 Si 2 , GdNi 5 Si 3 , GdNi 4 Si, GdNi 2 Si 2 , GdNiSi 3 , GdNiSi 2 , Gd 3 Ni 6 Si 2 and GdNiSi) is confirmed and three new compounds (GdNisub(0.2)Sisub(1.8), Gdsub(2)Nisub(1-0.8)Sisub(1-1.2), Gd 5 NiSi 4 ) are found. On the base of Gd 2 Si 3 compound up to 0.15 at. Ni fractions, an interstitial solid solution is formed up to 0.25 at Ni fractions dissolution continues of substitution type. The Gd-Ni-Si system is similar to the Y-Ni-Si system

Targeted synthesis of novel hierarchical sandwiched NiO/C arrays as high-efficiency lithium ion batteries anode

Science.gov (United States)

Feng, Yangyang; Zhang, Huijuan; Li, Wenxiang; Fang, Ling; Wang, Yu

2016-01-01

In this contribution, the novel 2D sandwich-like NiO/C arrays on Ti foil are successfully designed and fabricated for the first time via simple and controllable hydrothermal process. In this strategy, we use green glucose as carbon source and ultrathin Ni(OH)2 nanosheet arrays as precursor for NiO nanoparticles and sacrificial templates for coupled graphitized carbon layers. This advanced sandwiched composite can not only provide large surface area for numerous active sites and continuous contact between active materials and electrolyte, but also protect the active nanoparticles from aggregation, pulverization and peeling off from conductive substrates. Furthermore, the porous structure derived from lots of substances loss under high-temperature calcinations can effectively buffer possible volume expansion and facilitate ion transfer. In this article, sandwiched NiO/C arrays, utilized as anode for LIBs, demonstrated high specific capacity (∼1458 mAh g-1 at 500 mA g-1) and excellent rate performance and cyclablity (∼95.7% retention after 300 cycles).

OpenNI cookbook

CERN Document Server

Falahati, Soroush

2013-01-01

This is a Cookbook with plenty of practical recipes enriched with explained code and relevant screenshots to ease your learning curve. If you are a beginner or a professional in NIUI and want to write serious applications or games, then this book is for you. Even OpenNI 1 and OpenNI 1.x programmers who want to move to new versions of OpenNI can use this book as a starting point. This book uses C++ as the primary language but there are some examples in C# and Java too, so you need to have about a basic working knowledge of C or C++ for most cases.

Mechanochemical Synthesis of Nanostructured MgXNi1-XO Compound by Mg-NiO Mixture

Directory of Open Access Journals (Sweden)

Nader Setoudeh

2017-06-01

Full Text Available Synthesis of magnesium nickel oxide phase such as MgxNi1-xO solid solutions has been studied in this research article using mechnochmical reaction between magnesium and nickel oxide. Mixtures of magnesium powder and nickel oxide (Mg+NiO with stoichiometric compositions were milled for different times in a planetary ball mill. Reduction reaction of nickel oxide by magnesium via a mechanically induced self-sustaining reaction (MSR was confirmed in the XRD measurements of the as-milled samples. Formation of nanostructured magnesium nickel oxide phases (such as Mg0.4Ni0.6O or MgNiO2 was observed after isothermal heating of the 30 minutes milled samples at 1000°C where nickel phase seems to disappear in XRD patterns. The traces of phases such as Mg0.4Ni0.6O or MgNiO2 were also observed in the as-milled mixtures. Therefore, the XRD results of the as-milled samples suggested that the formation of magnesium nickel oxide phases could be possible even after prolonged milling. The XRD and SEM results of both as-milled and isothermally heated samples indicated that the crystallite size and particle size of the final products reached to nanoscale after milling. Morphological and compositional evolution of the samples after heat treatment was monitored through SEM imaging and elemental analyses. The results confirmed that the composition of final product is close to Mg0.4Ni0.6O compound.

Kinetics of Ni:C Thin Film Composition Formation at Different Temperatures and Fluxes

Directory of Open Access Journals (Sweden)

Gediminas KAIRAITIS

2013-09-01

Full Text Available In this work analysis considering Ni:C thin films growth on thermaly oxidized Si substrate by proposed kinetic model is presented. Model is built considering experimental results where microstructure evolution as a function of the substrate temperature and metal content of Ni:C nanocomposite films grown by hyperthermal ion deposition is investigated. The proposed kinetic model is based on the rate equations and includes processes of adsorption, surface segregation, diffusion, chemical reactions of constituents. The experimental depth profile curves were fitted by using proposed model. The obtained results show a good agreement with experiment taking into account concentration dependent diffusion. It is shown by modeling that with the increase of substrate temperature the process of nickel surface segregation becomes most important. DOI: http://dx.doi.org/10.5755/j01.ms.19.3.5234

In situ synthesis of TiB2-TiC particulates locally reinforced medium carbon steel-matrix composites via the SHS reaction of Ni-Ti-B4C system during casting

International Nuclear Information System (INIS)

Wang, H.Y.; Huang, L.; Jiang, Q.C.

2005-01-01

The fabrication of medium carbon steel-matrix composites locally reinforced with in situ TiB 2 -TiC particulates using self-propagating high-temperature synthesis (SHS) reaction of Ni-Ti-B 4 C system during casting was investigated. X-ray diffraction (XRD) results reveal that the exotherm of 1042 deg. C initiated by heat release of the solid state reaction in the differential thermal analysis (DTA) curve is an incomplete reaction in Ni-Ti-B 4 C system. As-cast microstructures of the in situ processed composites reveal a relatively uniform distribution of TiB 2 -TiC particulates in the locally reinforced regions. Furthermore, the particulate size and micro-porosity in the locally reinforced regions are significantly decreased with the increasing of the Ni content in the preforms. For a Ni content of 30 and 40 wt.%, near fully dense composites locally reinforced with in situ TiB 2 and TiC particulates can be fabricated. Although most of fine TiB 2 and TiC particulates which form by the reaction-precipitation mechanism during SHS reaction are present in the locally reinforced region, some large particulates which form by the nucleation-growth mechanism during solidification are entrapped inside the Fe-rich region located in the reinforcing region or inside the matrix region nearby the interface between matrix and reinforcing region. The hardness of the reinforcing region in the composite is significantly higher than that of the unreinforced medium carbon steel. Furthermore, the hardness values of the composites synthesized from 30 to 40 wt.% Ni-Ti-B 4 C systems are higher than those of the composites synthesized from 10 to 20 wt.% Ni-Ti-B 4 C systems

Reaction of intermetallic compounds of the ScT composition (T=Ag, Cu, Zn, Ni) with hydrogen

International Nuclear Information System (INIS)

Shilkin, S.P.; Volkova, L.S.; Tarasov, B.P.

1995-01-01

Reaction of intermetallic compounds of ScT composition (T=Ag, Cu, Zn, Ni), crystallized in CsCl structural type, with hydrogen at 0.2-10 MPa pressure and 293-673 K temperature is studied by chemical, x-ray phase and complex thermogravimetry analysis methods. It is shown that under such conditions hydrogen absorption by ScAg and ScCu is accompanied by the decay of their source matrices into scandium dihydride and metal silver and copper respectively. For ScZn a fine-dispersion mixture of scandium dihydride with zinc and hydride phase of a new zinc-containing intermetallic compound appears to be the finite reaction product. In case of ScNi a hydride phase of ScNiH 2.6 composition is produced, which is crystallized in a rhombic syngony with the lattice periods: a=0.5281±0.0007, b=0.7393±0.0009 and c=0.3327±0.0004 nm. 9 refs.; 2 tabs

Magnetic phase diagram of ErNi2B2C

DEFF Research Database (Denmark)

Jensen, A.; Toft, K.N.; Abrahamsen, A.B.

2004-01-01

The magnetic phase diagram of the superconductor ErNi2B2C (T-c = 11 K and T-N = 6 K) has been studied by neutron diffraction as a function of temperature and magnetic field applied along the symmetry directions [010], [110] and [001] of the tetragonal crystal structure. A series of commensurate...... magnetic structures, consistent with a transversely polarized spin-density wave with modulation vectors Q = n/ma* (0.55 less than or equal to n/m field model that has been established from...... an analysis of bulk magnetization and zero-field neutron diffraction data. The model accounts for most of the observed features but fails to explain the occurrence of a small component Qdelta approximate to -0.005b* observed close to H-c2 when the field is applied along [110]. (C) 2004 Elsevier B.V. All...

Induced 3d and 4f magnetism in Gd{sub 1-x}Pr{sub x}Ni{sub 2} Laves phase alloys

Energy Technology Data Exchange (ETDEWEB)

Bouziane, K [Department of Physics, College of Science, Sultan Qaboos University, PO Box 36, Al-Khodh 123 (Oman); Carboni, C [Department of Physics, College of Science, Sultan Qaboos University, PO Box 36, Al-Khodh 123 (Oman); Morrison, C [School of Physics and Astronomy, University of Southampton, Highfield, Southampton SO17 1BJ (United Kingdom)

2008-01-16

The series of Gd{sub 1-x}Pr{sub x}Ni{sub 2} (x = 0.25, 0.40, and 0.60) polycrystalline samples has been investigated using x-ray diffraction and magnetometry. The x-ray diffraction measurements showed that the lattice constant and the relative intensities of the C15 superstructure I{sub 511}/I{sub 440} and I{sub 511}/I{sub 220} increase with the praseodymium content, reflecting an increasing number of ordered vacancies at the 4a sites. The temperature dependences of the zero-field cooled (M{sub ZFC}(T)) and field cooled (M{sub FC}(T)) magnetizations show that a moment is induced by the gadolinium on the Pr{sup 3+} ion and on the nickel subsystem. In the ordered phase both induced moments are antiparallel to that of the Gd{sup 3+} ion. A cusp is observed at a temperature T{sub max} in the M{sub ZFC}(T) curve. Both critical temperatures T{sub c} and T{sub max} are found to decrease with increasing praseodymium content, indicating a reduction in strength of the antiparallel coupling for Gd-Pr and Gd-Ni pairs.

In-situ formation of Ni4Ti3 precipitate and its effect on pseudoelasticity in selective laser melting additive manufactured NiTi-based composites

Science.gov (United States)

Gu, Dongdong; Ma, Chenglong

2018-05-01

Selective laser melting (SLM) additive manufacturing technology was applied to synthesize NiTi-based composites via using ball-milled Ti, Ni, and TiC mixed powder. By transmission electron microscope (TEM) characterization, it indicated that the B2 (NiTi) matrix was obtained during SLM processing. In spite of more Ti content (the Ti/Ni ratio >1), a mass of Ni-rich intermetallic compounds containing Ni4Ti3 with nanostructure features and eutectic Ni3Ti around in-situ Ti6C3.75 dendrites were precipitated. Influence of the applied laser volume energy density (VED) on the morphology and content of Ni4Ti3 precipitate was investigated. Besides, nanoindentation test of the matrix was performed in order to assess pseudoelastic recovery behavior of SLM processed NiTi-based composites. At a relatively high VED of 533 J/mm3, the maximum pseudoelastic recovery was obtained due to the lowest content of Ni4Ti3 precipitates. Furthermore, the precipitation mechanism of in-situ Ni4Ti3 was present based on the redistribution of titanium element and thermodynamics analysis, and then the relationship of Ni4Ti3 precipitate, VED and pseudoelastic recovery behavior was also revealed.

Ni.sub.3 Al-based intermetallic alloys having improved strength above 850.degree. C.

Science.gov (United States)

Liu, Chain T.

2000-01-01

Intermetallic alloys composed essentially of: 15.5% to 17.0% Al, 3.5% to 5.5% Mo, 4% to 8% Cr, 0.04% to 0.2% Zr, 0.04% to 1.5% B, balance Ni, are characterized by melting points above 1200.degree. C. and superior strengths at temperatures above 1000.degree. C.

The Effect of Milling Time on the Microstructural Characteristics and Strengthening Mechanisms of NiMo-SiC Alloys Prepared via Powder Metallurgy.

Science.gov (United States)

Yang, Chao; Muránsky, Ondrej; Zhu, Hanliang; Thorogood, Gordon J; Avdeev, Maxim; Huang, Hefei; Zhou, Xingtai

2017-04-06

A new generation of alloys, which rely on a combination of various strengthening mechanisms, has been developed for application in molten salt nuclear reactors. In the current study, a battery of dispersion and precipitation-strengthened (DPS) NiMo-based alloys containing varying amounts of SiC (0.5-2.5 wt %) were prepared from Ni-Mo-SiC powder mixture via a mechanical alloying (MA) route followed by spark plasma sintering (SPS) and rapid cooling. Neutron Powder Diffraction (NPD), Electron Back Scattering Diffraction (EBSD), and Transmission Electron Microscopy (TEM) were employed in the characterization of the microstructural properties of these in-house prepared NiMo-SiC DPS alloys. The study showed that uniformly-dispersed SiC particles provide dispersion strengthening, the precipitation of nano-scale Ni₃Si particles provides precipitation strengthening, and the solid-solution of Mo in the Ni matrix provides solid-solution strengthening. It was further shown that the milling time has significant effects on the microstructural characteristics of these alloys. Increased milling time seems to limit the grain growth of the NiMo matrix by producing well-dispersed Mo₂C particles during sintering. The amount of grain boundaries greatly increases the Hall-Petch strengthening, resulting in significantly higher strength in the case of 48-h-milled NiMo-SiC DPS alloys compared with the 8-h-milled alloys. However, it was also shown that the total elongation is considerably reduced in the 48-h-milled NiMo-SiC DPS alloy due to high porosity. The porosity is a result of cold welding of the powder mixture during the extended milling process.

Electron Microscopy Characterization of Ni-Cr-B-Si-C Laser Deposited Coatings

NARCIS (Netherlands)

Hemmati, I.; Rao, J. C.; Ocelik, V.; De Hosson, J. Th. M.

During laser deposition of Ni-Cr-B-Si-C alloys with high amounts of Cr and B, various microstructures and phases can be generated from the same chemical composition that results in heterogeneous properties in the clad layer. In this study, the microstructure and phase constitution of a high-alloy

Frustrated ground state in the metallic Ising antiferromagnet Nd2Ni2In

Science.gov (United States)

Sala, G.; Mašková, S.; Stone, M. B.

2017-10-01

We used inelastic neutron scattering measurements to examine the intermetallic Ising antiferromagnet Nd2Ni2In . The dynamical structure factor displays a spectrum with multiple crystal field excitations. These crystal field excitations consist of a set of four transitions covering a range of energies between 4 and 80 meV. The spectrum is very sensitive to the temperature, and we observed a softening and a shift in the energies above the transition temperature of the system. The analysis of the crystalline electric field scheme confirms the Ising nature of the spins and their orientation as proposed by previous studies. We characterized Nd2Ni2In as a large moment intermetallic antiferromagnet with the potential to support a geometrically frustrated Shastry-Sutherland lattice.

Effect of (Nd, Ni) co-doped on the multiferroic and photocatalytic properties of BiFeO{sub 3}

Energy Technology Data Exchange (ETDEWEB)

Vanga, Pradeep Reddy [Nanomaterials Laboratory, Department of Physics, National Institute of Technology, Tiruchirapalli 620 015 (India); Mangalaraja, R.V. [Department of Materials Engineering, University of Concepcion, Concepcion (Chile); Ashok, M., E-mail: ashokm@nitt.edu [Nanomaterials Laboratory, Department of Physics, National Institute of Technology, Tiruchirapalli 620 015 (India)

2015-12-15

Highlights: • Sol–gel synthesis. • Saturation magnetization and ferroelectricity increases in Ni co-doped samples. • Conduction mechanism is different in Nd doped and (Nd, Ni) co-doped samples. • Samples show good photocatalytic activity in the presence of H{sub 2}O{sub 2}. - Abstract: Bi{sub 0.95}Nd{sub 0.05}Fe{sub 1−x}Ni{sub x}O{sub 3} (x = 0, 0.01, 0.03 and 0.05) samples are synthesized by solgel method. The phase and crystal structure of the samples are confirmed by X-ray diffraction studies, Rietveld refinement is performed to calculate the structural parameters. The reflectance spectra show bands in UV and visible region and the optical band gap is calculated using Kulbeka–Munk function. The magnetization and leakage current density are strongly influenced by doping. Different conduction mechanisms are observed in Nd doped and Ni co-doped samples. All the samples exhibit ferroelectric nature at various frequencies. Photocatalytic activities of the samples are determined by the degradation of methylene blue dye in the presence of visible light and H{sub 2}O{sub 2} which shows samples are good photo-Fenton like catalyst.

Magnetocaloric effect in textured rare earth intermetallic compound ErNi

Directory of Open Access Journals (Sweden)

Aparna Sankar

2018-05-01

Full Text Available Melt-spun ErNi crystallizes in orthorhombic FeB-type structure (Space group Pnma, no. 62 similar to the arc-melted ErNi compound. Room temperature X-ray diffraction (XRD experiments reveal the presence of texture and preferred crystal orientation in the melt-spun ErNi. The XRD data obtained from the free surface of the melt-spun ErNi show large intensity enhancement for (1 0 2 Bragg reflection. The scanning electron microscopy image of the free surface depicts a granular microstructure with grains of ∼1 μm size. The arc-melted and the melt-spun ErNi compounds order ferromagnetically at 11 K and 10 K (TC respectively. Field dependent magnetization (M-H at 2 K shows saturation behaviour and the saturation magnetization value is 7.2 μB/f.u. for the arc-melted ErNi and 7.4 μB/f.u. for the melt-spun ErNi. The isothermal magnetic entropy change (ΔSm close to TC has been calculated from the M-H data. The maximum isothermal magnetic entropy change, -ΔSmmax, is ∼27 Jkg-1K-1 and ∼24 Jkg-1K-1 for the arc-melted and melt-spun ErNi for 50 kOe field change, near TC. The corresponding relative cooling power values are ∼440 J/kg and ∼432 J/kg respectively. Although a part of ΔSm is lost to crystalline electric field (CEF effects, the magnetocaloric effect is substantially large at 10 K, thus rendering melt-spun ErNi to be useful in low temperature magnetic refrigeration applications such as helium gas liquefaction.

Magnetocaloric effect in textured rare earth intermetallic compound ErNi

Science.gov (United States)

Sankar, Aparna; Chelvane, J. Arout; Morozkin, A. V.; Nigam, A. K.; Quezado, S.; Malik, S. K.; Nirmala, R.

2018-05-01

Melt-spun ErNi crystallizes in orthorhombic FeB-type structure (Space group Pnma, no. 62) similar to the arc-melted ErNi compound. Room temperature X-ray diffraction (XRD) experiments reveal the presence of texture and preferred crystal orientation in the melt-spun ErNi. The XRD data obtained from the free surface of the melt-spun ErNi show large intensity enhancement for (1 0 2) Bragg reflection. The scanning electron microscopy image of the free surface depicts a granular microstructure with grains of ˜1 μm size. The arc-melted and the melt-spun ErNi compounds order ferromagnetically at 11 K and 10 K (TC) respectively. Field dependent magnetization (M-H) at 2 K shows saturation behaviour and the saturation magnetization value is 7.2 μB/f.u. for the arc-melted ErNi and 7.4 μB/f.u. for the melt-spun ErNi. The isothermal magnetic entropy change (ΔSm) close to TC has been calculated from the M-H data. The maximum isothermal magnetic entropy change, -ΔSmmax, is ˜27 Jkg-1K-1 and ˜24 Jkg-1K-1 for the arc-melted and melt-spun ErNi for 50 kOe field change, near TC. The corresponding relative cooling power values are ˜440 J/kg and ˜432 J/kg respectively. Although a part of ΔSm is lost to crystalline electric field (CEF) effects, the magnetocaloric effect is substantially large at 10 K, thus rendering melt-spun ErNi to be useful in low temperature magnetic refrigeration applications such as helium gas liquefaction.

PtNi Alloy Cocatalyst Modification of Eosin Y-Sensitized g-C3N4/GO Hybrid for Efficient Visible-Light Photocatalytic Hydrogen Evolution

Science.gov (United States)

Wang, Peng; Zong, Lanlan; Guan, Zhongjie; Li, Qiuye; Yang, Jianjun

2018-02-01

An economic and effective Pt-based alloy cocatalyst has attracted considerable attention due to their excellent catalytic activity and reducing Pt usage. In this study, PtNi alloy cocatalyst was successfully decorated on the g-C3N4/GO hybrid photocatalyst via a facile chemical reduction method. The Eosin Y-sensitized g-C3N4/PtNi/GO-0.5% composite photocatalyst yields about 1.54 and 1178 times higher hydrogen evolution rate than the Eosin Y-sensitized g-C3N4/Pt/GO-0.5% and g-C3N4/Ni/GO-0.5% samples, respectively. Mechanism of enhanced performance for the g-C3N4/PtNi/GO composite was also investigated by different characterization, such as photoluminescence, transient photocurrent response, and TEM. These results indicated that enhanced charge separation efficiency and more reactive sites are responsible for the improved hydrogen evolution performance due to the positive synergetic effect between Pt and Ni. This study suggests that PtNi alloy can be used as an economic and effective cocatalyst for hydrogen evolution reaction. [Figure not available: see fulltext.

Effect of SiC Nanowhisker on the Microstructure and Mechanical Properties of WC-Ni Cemented Carbide Prepared by Spark Plasma Sintering

Directory of Open Access Journals (Sweden)

Xiaoyong Ren

2014-01-01

Full Text Available Ultrafine tungsten carbide-nickel (WC-Ni cemented carbides with varied fractions of silicon carbide (SiC nanowhisker (0–3.75 wt.% were fabricated by spark plasma sintering at 1350°C under a uniaxial pressure of 50 MPa with the assistance of vanadium carbide (VC and tantalum carbide (TaC as WC grain growth inhibitors. The effects of SiC nanowhisker on the microstructure and mechanical properties of the as-prepared WC-Ni cemented carbides were investigated. X-ray diffraction analysis revealed that during spark plasma sintering (SPS Ni may react with the applied SiC nanowhisker, forming Ni2Si and graphite. Scanning electron microscopy examination indicated that, with the addition of SiC nanowhisker, the average WC grain size decreased from 400 to 350 nm. However, with the additional fractions of SiC nanowhisker, more and more Si-rich aggregates appeared. With the increase in the added fraction of SiC nanowhisker, the Vickers hardness of the samples initially increased and then decreased, reaching its maximum of about 24.9 GPa when 0.75 wt.% SiC nanowhisker was added. However, the flexural strength of the sample gradually decreased with increasing addition fraction of SiC nanowhisker.

Rapid synthesis of binary α-NiS–β-NiS by microwave autoclave for rechargeable lithium batteries

International Nuclear Information System (INIS)

Idris, Nurul Hayati; Rahman, Md Mokhlesur; Chou, Shu-Lei; Wang Jiazhao; Wexler, David; Liu, Hua-Kun

2011-01-01

Highlights: ► NiS has been synthesized by a rapid, one-pot, hydrothermal microwave autoclave method. ► The α-NiS–β-NiS sample synthesized at 160 °C yielded good electrochemical performance in terms of high reversible capacity (320 mAh g −1 at 0.1C up to 100 cycles). ► At high rates, the sample operated at a good fraction of its capacity. - Abstract: To reduce the reaction time, electrical energy consumption, and cost, binary α-NiS–β-NiS has been synthesized by a rapid, one-pot, hydrothermal autoclave microwave method within 15 min at temperatures of 160–180 °C. The microstructure and morphology of the α-NiS–β-NiS products were characterized by means of X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), and transmission electron microscopy (TEM). At 140 °C, pure hexagonal NiAs-type α-NiS phase was identified from the XRD patterns. With increasing reaction temperature (160–180 °C), the XRD evidence indicates that an increasing fraction of rhombohedral millerite-like β-NiS is formed as a secondary phase. The α-NiS–β-NiS sample synthesized at 160 °C yielded good electrochemical performance in term of high reversible capacity (320 mAh g −1 at 0.1C up to 100 cycles). Even at high rates, the sample operated at a good fraction of its capacity. The likely contributing factor to the superior electrochemical performance of the α-NiS–β-NiS sample could be related to the improved morphology. TEM imaging confirmed that needle-like protrusions connect the clusters of α-NiS particles, and the individual protrusions indicated a very high surface area including folded sheet morphology, which helps to dissipate the surface accumulation of Li + ions and facilitate rapid mobility. These factors help to enhance the amount of lithium intercalated within the material.

A model compound (methyl oleate, oleic acid, triolein) study of triglycerides hydrodeoxygenation over alumina-supported NiMo sulfide

NARCIS (Netherlands)

Coumans, A.E.; Hensen, E.J.M.

We studied hydrodeoxygenation of model compounds for vegetable oil into diesel-range hydrocarbons on a sulfided NiMo/γ-Al2O3 catalyst under trickle-flow conditions. Methyl oleate (methyl ester of oleic acid, a C18 fatty acid with one unsaturated bond in the chain) represented the C18 alkyl esters in

Local structural distortion and electronic modifications in PrNiO3 across the metal-insulator transition

International Nuclear Information System (INIS)

Piamonteze, C.; Tolentino, H.C.N.; Ramos, A.Y.; Massa, N. E.; Alonso, J.A.; Martinez-Lope, M.J.; Casais, M.T.

2003-01-01

Local electronic and structural properties of PrNiO3 perovskite were studied by means of X-ray Absorption Spectroscopy at Ni K and L edges. The EXAFS results at Ni K edge show a structural transition from three different Ni-O bond-lengths at the insulating phase to two Ni-O bond-lengths above TMI. These results were interpreted as being due to a transition from a structure with two different Ni sites at the insulating phase to one distorted Ni site at the metallic phase. The Ni L edge spectra show a remarkable difference between the spectra measured at the insulating and metallic phases that indicates a decreasing degree of hybridization between Ni3d and O2p bands from the metallic to the insulating phase

Microstructure and wear behavior of {gamma}/Al{sub 4}C{sub 3}/TiC/CaF{sub 2} composite coating on {gamma}-TiAl intermetallic alloy prepared by Nd:YAG laser cladding

Energy Technology Data Exchange (ETDEWEB)

Liu Xiubo [School of Mechanical and Electronic Engineering, 178 Ganjiang East Road, Soochow University, Suzhou 215021 (China)], E-mail: liubobo0828@yahoo.com.cn; Shi Shihong [School of Mechanical and Electronic Engineering, 178 Ganjiang East Road, Soochow University, Suzhou 215021 (China); Guo Jian [School of Materials and Chemical Engineering, Zhongyuan Institute of Technology, 41 Zhongyuan West Road, Zhengzhou 450007 (China); Fu Geyan; Wang Mingdi [School of Mechanical and Electronic Engineering, 178 Ganjiang East Road, Soochow University, Suzhou 215021 (China)

2009-03-15

As a further step in obtaining high performance elevated temperature self-lubrication anti-wear composite coatings on TiAl alloy, a novel Ni-P electroless plating method was adopted to encapsulate the as-received CaF{sub 2} in the preparation of precursor NiCr-Cr{sub 3}C{sub 2}-CaF{sub 2} mixed powders with an aim to decrease its mass loss and increase its compatibility with the metal matrix during a Nd:YAG laser cladding. The microstructure of the coating was examined using X-ray diffraction (XRD), scanning electron microscope (SEM) and energy dispersive spectroscopy (EDS) and the friction and wear behavior of the composite coatings sliding against the hardened 0.45% C steel ring was evaluated using a block-on-ring wear tester at room temperature. It was found that the coating had a unique microstructure consisting of primary dendrites TiC and block Al{sub 4}C{sub 3} carbides reinforcement as well as fine isolated spherical CaF{sub 2} solid lubrication particles uniformly dispersed in the NiCrAlTi ({gamma}) matrix. The good friction-reducing and anti-wear abilities of the laser clad composite coating was suggested to the Ni-P electroless plating and the attendant reduction of mass loss of CaF{sub 2} and the increasing of it's wettability with the NiCrAlTi ({gamma}) matrix during the laser cladding process.

Cambios de código en niños mientras juegan videojuegos

Directory of Open Access Journals (Sweden)

Armando Robles Hmilowicz

2010-07-01

Full Text Available El trabajo analiza los cambios de código en niños bilingües en el contexto de los juegos de vídeo. Para ello emplea el análisis interaccional sobre un corpus integrado por interacciones de una pareja de hermanos con padres mexicanos que viven desde hace 10 años en Estados Unidos, mientras juegan videojuegos. La familia se encuentra de vacaciones en México, por lo que además de interactuar entre sí, los niños interactúan con otros niños (sus primos, dando origen a distintas situaciones comunicativas que son analizadas. Se distingue el uso de dos tipos de cambio de código para el contexto del videojuego: cambios de orientación interna (relacionados directamente con el videojuego y cambios de orientación externa (no relacionados con el juego en sí. El estudio pone a prueba la utilidad de estas categorías y propone que los cambios de código pueden formar parte de un repertorio de recursos comunicativos que los niños están aprendiendo a utilizar en este contexto novedoso, por lo cual puede resultar interesante desde un punto de vista didáctico.---------------------------------------------The article analyses the code-switching of bilingual children in the context of video game playing. Interaction analysis is carried out on an integrated corpus consisting of a pair of siblings (4 and 8 years old of Mexican descent whose parents have lived in the United States of America for ten years. The corpus consists of data taken while they were playing videogames during holidays taken in Mexico, therefore there is not only interaction between the siblings but also with their cousins. Two types of code-switching can be identified within the context of videogame playing: changes with internal orientation (related directly with the videogame and changes with external orientation (not directly related to the game. The study interrogates the usefulness of these categories and proposes that the code-switching may form a part of the repertoire of

Induction of apoptosis in cancer cells by NiZn ferrite nanoparticles through mitochondrial cytochrome C release

Directory of Open Access Journals (Sweden)

Al-Qubaisi MS

2013-10-01

Full Text Available Mothanna Sadiq Al-Qubaisi,1 Abdullah Rasedee,1,2 Moayad Husein Flaifel,3 Sahrim Hj Ahmad,3 Samer Hussein-Al-Ali,1 Mohd Zobir Hussein,4 Zulkarnain Zainal,4 Fatah H Alhassan,4 Yun H Taufiq-Yap,4 Eltayeb EM Eid,5 Ismail Adam Arbab,1 Bandar A Al-Asbahi,3 Thomas J Webster,6,7 Mohamed Ezzat El Zowalaty1,8,9 1Institute of Bioscience, 2Faculty of Veterinary Medicine, Universiti Putra Malaysia, 3Faculty of Science and Technology, Universiti Kebangsaan Malaysia, 4Faculty of Science, Universiti Putra Malaysia, Selangor, Malaysia; 5College of Pharmacy, Qassim University, Buraidah, Saudi Arabia; 6Department of Chemical Engineering and Program in Bioengineering, Northeastern University, Boston, MA, USA; 7Center of Excellence for Advanced Materials Research, King Abdulaziz University, Jeddah, Saudi Arabia; 8Faculty of Pharmacy, Zagazig University, Zagazig, Egypt; 9Faculty of Public Health and Tropical Medicine, Jazan University, Jazan, Saudi Arabia Abstract: The long-term objective of the present study was to determine the ability of NiZn ferrite nanoparticles to kill cancer cells. NiZn ferrite nanoparticle suspensions were found to have an average hydrodynamic diameter, polydispersity index, and zeta potential of 254.2 ± 29.8 nm, 0.524 ± 0.013, and -60 ± 14 mV, respectively. We showed that NiZn ferrite nanoparticles had selective toxicity towards MCF-7, HepG2, and HT29 cells, with a lesser effect on normal MCF 10A cells. The quantity of Bcl-2, Bax, p53, and cytochrome C in the cell lines mentioned above was determined by colorimetric methods in order to clarify the mechanism of action of NiZn ferrite nanoparticles in the killing of cancer cells. Our results indicate that NiZn ferrite nanoparticles promote apoptosis in cancer cells via caspase-3 and caspase-9, downregulation of Bcl-2, and upregulation of Bax and p53, with cytochrome C translocation. There was a concomitant collapse of the mitochondrial membrane potential in these cancer cells when treated

Nernst effect of Ni-doped NdBa2Cu3O7-δ and transport properties in UPt2Si2

International Nuclear Information System (INIS)

Johannsen, Niko

2008-05-01

In this thesis, the Nernst effect in high-temperature superconductors is investigated. Large Nernst voltages were found to survive up to temperatures that reach far out of the superconducting phase. This was extensively studied thereafter in wide doping range of the high-T c 's. We were able to significantly expand these studies by tuning T * and T ν independently. This was done by inducing Ni ions into the CuO planes of NdBa 2 {Cu 1-y Ni y } 3 O 7-δ which allowed to study the Nernst effect in a wide parameter range. This is done on one hand in dependence of the oxygen content which varies the charge carrier concentration. On the other hand, the Ni concentration is varied from 0% to 12%, thereby enhancing T * and simultaneously suppressing T c with increasing concentrations. The temperatures to which the anomalous Nernst signal is detectable is the onset temperature T ν . The goal of this work was to find out whether T ν follows T c or T * . The onset temperatures of the anomalous Nernst signals are determined as the slightest detectable deviation from the quasiparticle background above T c . In the second part of this work, the Nernst effect and other transport properties of UPt 2 Si 2 , including electrical ones such as the resistivity and the Hall effect and thermal ones, as the thermal conductivity, the thermopower and the Righi-Leduc effect were investigated. (orig.)

DAR LA PALABRA. En torno al lenguaje de los niños y las niñas en la cárcel

Directory of Open Access Journals (Sweden)

Bibiana Escobar\\u2013García

2017-01-01

Full Text Available Este trabajo es parte de la investigación, los cuerpos de la excepción. Maternidad e infancia en la cárcel. Corresponde al referente teórico de una categoría vinculada al desarrollo del lenguaje de los niños en la institución carcelaria. El supuesto básico señala las condiciones de empobrecimiento del lenguaje en las cárceles y lo vincula a la suspensión antropológica mediante la cual allí se procede. Se asume que si bien la función habitual que se imagina para el sistema carcelario es la de normalizar a los sujetos, esta función da lugar a una más económica: proteger a la sociedad de los desechos antropológicos que repetidamente produce la Modernidad en el presente. No obstante, dicha protección sacrifica las condiciones de posibilidad de los niños que en la cárcel comparten la condena de sus madres.

Ammonia-evaporation-induced construction of three-dimensional NiO/g-C3N4 composite with enhanced adsorption and visible light-driven photocatalytic performance

Science.gov (United States)

Tzvetkov, George; Tsvetkov, Martin; Spassov, Tony

2018-07-01

Novel visible light-driven heterostructured NiO/g-C3N4 photocatalyst has been designed and successfully prepared via ammonia-evaporation-induced method. The synthetic strategy consists of grafting the surface of g-C3N4 with Ni(NH3)62+ complex followed by its hydrolysis at lower pH to form nano-wrinkled thin film of α-Ni(OH)2. The final NiO/g-C3N4 hybrid was obtained after calcination of the Ni(OH)2/g-C3N4 precursor at 350 °C. Scanning electron microscopy, transmission electron microscopy, X-ray diffraction, FTIR, N2 adsorption/desorption, UV-vis diffuse reflectance and photoluminescence spectroscopy were used to characterize the resulting material. Our results revealed the formation of meso-/macroporous three-dimensional hierarchical honeycomb-like structure with high BET surface area (141 m2 g-1). The photocatalytic performance of the composite under visible light (λ > 400 nm) irradiation was evaluated through degradation of Malachite Green (MG) from aqueous medium at room temperature (25 °C). For the sake of comparison, the physico-chemical and photocatalytic properties of the pristine g-C3N4 and nanostructured NiO were also examined. Results indicated that NiO/g-C3N4 is much more active than pristine g-C3N4 and NiO in the photodegradation of MG. The enhanced photocatalytic performance of the composite was mainly attributed to the combination of high adsorption capacity which facilitates the direct redox reactions of dye and the efficient inhibition of photo-generated electron-hole pair recombination. Superoxide radicals (•O2-) and photo-generated holes (h+) were found to be the main active species in the process.

Impact of Transgenic Brassica napus Harboring the Antifungal Synthetic Chitinase (NiC Gene on Rhizosphere Microbial Diversity and Enzyme Activities

Directory of Open Access Journals (Sweden)

Mohammad S. Khan

2017-07-01

Full Text Available Transgenic Brassica napus harboring the synthetic chitinase (NiC gene exhibits broad-spectrum antifungal resistance. As the rhizosphere microorganisms play an important role in element cycling and nutrient transformation, therefore, biosafety assessment of NiC containing transgenic plants on soil ecosystem is a regulatory requirement. The current study is designed to evaluate the impact of NiC gene on the rhizosphere enzyme activities and microbial community structure. The transgenic lines with the synthetic chitinase gene (NiC showed resistance to Alternaria brassicicola, a common disease causing fungal pathogen. The rhizosphere enzyme analysis showed no significant difference in the activities of fivesoil enzymes: alkalyine phosphomonoestarase, arylsulphatase, β-glucosidase, urease and sucrase between the transgenic and non-transgenic lines of B. napus varieties, Durr-e-NIFA (DN and Abasyne-95 (AB-95. However, varietal differences were observed based on the analysis of molecular variance. Some individual enzymes were significantly different in the transgenic lines from those of non-transgenic but the results were not reproducible in the second trail and thus were considered as environmental effect. Genotypic diversity of soil microbes through 16S–23S rRNA intergenic spacer region amplification was conducted to evaluate the potential impact of the transgene. No significant diversity (4% for bacteria and 12% for fungal between soil microbes of NiC B. napus and the non-transgenic lines was found. However, significant varietal differences were observed between DN and AB-95 with 79% for bacterial and 54% for fungal diversity. We conclude that the NiC B. napus lines may not affect the microbial enzyme activities and community structure of the rhizosphere soil. Varietal differences might be responsible for minor changes in the tested parameters.

The crystal structure and electronic properties of a new metastable non-stoichiometric BaAl{sub 4}-type compound crystallized from amorphous La{sub 6}Ni{sub 34}Ge{sub 60} alloy

Energy Technology Data Exchange (ETDEWEB)

Hasegawa, Masashi [Institute for Materials Research, Tohoku University, Sendai, Katahira 980-8577 (Japan); Suzuki, Shoichiro [Institute for Materials Research, Tohoku University, Sendai, Katahira 980-8577 (Japan); Ohsuna, Tetsu [Institute for Materials Research, Tohoku University, Sendai, Katahira 980-8577 (Japan); Matsubara, Eiichiro [Institute for Materials Research, Tohoku University, Sendai, Katahira 980-8577 (Japan); Endo, Satoshi [Center for Low Temperature Science, Tohoku University, Sendai, Katahira 980-8577 (Japan); Inoue, Akihisa [Institute for Materials Research, Tohoku University, Sendai, Katahira 980-8577 (Japan)

2004-11-17

A new metastable La-Ge-Ni ternary BaAl{sub 4}-type (ThCr{sub 2}Si{sub 2}-type) compound, of which the space group is I4/mmm is synthesized. It is obtained by a polymorphic transformation from an La{sub 6}Ni{sub 34}Ge{sub 60} amorphous alloy on crystallizing. The formula of the compound is (La{sub 0.3}Ge{sub 0.7})(Ni{sub 0.85}Ge{sub 0.15}){sub 2}Ge{sub 2}. This indicates that it is highly non-stoichiometric compared to the stoichiometric LaNi{sub 2}Ge{sub 2}. It is found that the c-axis lattice parameter of this compound is much longer than that of LaNi{sub 2}Ge{sub 2}. It should be noted that the longer c-axis unit cell parameter is attributable only to the longer interlayer distance between Ge site and Ni site layers. The temperature dependences of electrical resistivity and thermoelectric power of the (La{sub 0.3}Ge{sub 0.7})(Ni{sub 0.85}Ge{sub 0.15}){sub 2}Ge{sub 2} compound and La{sub 6}Ni{sub 34}Ge{sub 60} amorphous alloy are also clarified. The comparison of these electronic properties between the two materials indicates that sp-electrons mainly contribute to the density of states around the Fermi level of this compound.

Oxidation behaviors of the TiNi/Ti{sub 2}Ni matrix composite coatings with different contents of TaC addition fabricated on Ti6Al4V by laser cladding

Energy Technology Data Exchange (ETDEWEB)

Lv, Y.H.; Li, J., E-mail: jacob_lijun@sina.com; Tao, Y.F.; Hu, L.F.

2016-09-15

The TiNi/Ti{sub 2}Ni matrix composite coatings were fabricated on Ti6Al4V by laser cladding the mixtures of NiCrBSi and different contents of TaC (0 wt%, 5 wt%, 15 wt%, 30 wt% and 40 wt%). Scanning electron microscopy (SEM), energy dispersive spectrometry (EDS) and X-ray diffractometry (XRD) were used to examine the microstructures of the coatings. Oxidation behaviors of these coatings were also investigated at 800 °C for 50 h in air. The results showed that the coating without TaC addition was mainly composed of TiNi/Ti{sub 2}Ni as the matrix and TiC/TiB{sub 2}/TiB as the reinforcement. TaC was dissolved completely and precipitated again during laser cladding. Ta and C from the added TaC mainly existed as the solute atoms in the solid solutions of TiC, TiB{sub 2} and TiB in the coatings with TaC addition. The addition of TaC refined the microstructures of the coatings. In the oxidation test, the oxidation process was divided into the violent oxidation stage and the slow oxidation stage. The oxidation rates of the substrate and the coatings with different contents of TaC (0, 5, 15, 30, 40 wt%) were 0.644, 0.287, 0.173, 0.161, 0.223 and 0.072 mg cm{sup −2} h{sup −1} in the first stage, 0.884, 0.215, 0.136, 0.126, 0.108 and 0.040 mg{sup 2} cm{sup −4} h{sup −1} in the second stage, respectively. The weight gain of these samples were 6.70, 3.30, 2.86, 2.64, 2.41 and 1.69 mg cm{sup −2}, respectively after the whole oxidation test. The oxidation film formed on the surface of the coating without TaC addition mainly consisted of TiO{sub 2}, Al{sub 2}O{sub 3}, and a small amount of NiO, Cr{sub 2}O{sub 3} and SiO{sub 2}. Moreover, Ta{sub 2}O{sub 5} was also formed on the surfaces of these coatings with different contents of TaC. The oxides formed during the oxidation test were supposed to be responsible for the improvement in oxidation resistance of these coatings. - Highlights: • The composite coatings with TaC addition were fabricated on Ti6Al4V by laser

Parasitismo intestinal en niños de círculos infantiles en un municipio

Directory of Open Access Journals (Sweden)

María del Carmen Hernández Alfaro

2014-04-01

Full Text Available Introducción: el parasitismo intestinal representa un importante problema de salud mundial por su alta prevalencia y distribución universal. Constituye una importante causa de morbilidad y mortalidad en lactantes y niños de todo el orbe. Objetivo: identificar la prevalencia de las principales especies parasitarias intestinales en círculos infantiles del municipio La Palma. Método: se realizó un estudio observacional descriptivo transversal, durante los meses de octubre y noviembre 2012, en el que se estudiaron 495 niños asistentes a los seis círculos infantiles del municipio La Palma. Fueron recolectadas por cada niño, 3 muestras fecales frescas, en días alternos, las que se procesaron con los métodos coproparasitológicos de examen directo y técnica de concentración de Ritchie- Willis. Resultados: el 48,3% de la muestra estaba parasitada, con una mayor prevalencia en el quinto año de vida (58,8%, predominó el sexo masculino (54,8%. Las especies más frecuentes fueron Giardia lamblia (38,1%, Entamoeba histolytica (30,1% y Enterobius vermicularis (19,2%. El poliparasitismo se apreció (12,2% de los niños, la asociación de parásitos muestra a Giardia lamblia en tres combinaciones. Junto al Enterobius vermicularis (37,2 %, con Entamoeba histolytica/E dispar (33,3 % y los tres a la vez (29,4%. Conclusiones: aproximadamente la mitad de los niños estudiados se encontraban parasitados, estos resultados fueron más frecuentes a partir del cuarto año de vida, con una mayor prevalencia en el sexo masculino en todas las especies parasitarias, predominado las infecciones por protozoarios, con mayor frecuencia Giardia lamblia y asociaciones de parásitos en varios casos.

Low content of Pt supported on Ni-MoC{sub x}/carbon black as a highly durable and active electrocatalyst for methanol oxidation, oxygen reduction and hydrogen evolution reactions in acidic condition

Energy Technology Data Exchange (ETDEWEB)

Zhang, Yan; Zang, Jianbing; Jia, Shaopei; Tian, Pengfei; Han, Chan; Wang, Yanhui, E-mail: diamond_wangyanhui@163.com

2017-08-01

Highlights: • Ni-MoC{sub x}/C catalyst support was synthesized by a two-step method. • 10Pt/Ni-MoC{sub x}/C was an active and durable low Pt catalyst for MOR, ORR and HER. • The high stability of 10Pt/Ni-MoC{sub x}/C was ascribed to the anchoring effect of MoC{sub x}. • High activity of 10Pt/Ni-MoC{sub x}/C was due to a synergistic of Pt, Ni, MoO{sub x} and MoC{sub x}. - Abstract: Nickel and molybdenum carbide modified carbon black (Ni-MoC{sub x}/C) was synthesized by a two-step microwave-assisted deposition/carbonthermal reduction method and characterized by X-ray diffraction, transmission electron microscopy, energy dispersive spectroscopy and X-ray photoelectron spectroscopy. The as-prepared Ni-MoC{sub x}/C supported Pt (10 wt%) electrocatalyst (10Pt/Ni-MoC{sub x}/C) was synthesized through a microwave-assisted reduction method and 10Pt/Ni-MoC{sub x}/C exhibited high electrocatalytic activity for methanol oxidation, oxygen reduction and hydrogen evolution reactions. Results showed that 10Pt/Ni-MoC{sub x}/C electrocatalyst had better electrocatalytic activity and stability performance than 20 wt% Pt/C (20Pt/C) electrocatalyst. Among them, the electrochemical surface area of 10Pt/Ni-MoC{sub x}/C reached 68.4 m{sup 2} g{sup −1}, which was higher than that of 20Pt/C (63.2 m{sup 2} g{sup −1}). The enhanced stability and activity of 10Pt/Ni-MoC{sub x}/C electrocatalyst were attributed to: (1) an anchoring effect of Ni and MoC{sub x} formed during carbonthermal reduction process; (2) a synergistic effect among Pt, Ni, MoO{sub x} and MoC{sub x}. These findings indicated that 10Pt/Ni-MoC{sub x}/C was a promising electrocatalyst for direct methanol fuel cells.

The new ternary pnictides Er12Ni30P21 and Er13Ni25As19: Crystal structures and magnetic properties

International Nuclear Information System (INIS)

Oryshchyn, Stepan; Babizhetskyy, Volodymyr; Zhak, Olga; Zelinska, Mariya; Pivan, Jean-Yves; Duppel, Viola; Simon, Arndt; Kienle, Lorenz

2010-01-01

The new ternary pnictides Er 12 Ni 30 P 21 and Er 13 Ni 25 As 19 have been synthesized from the elements. They crystallize with hexagonal structures determined from single-crystal X-ray data for Er 12 Ni 30 P 21 (space group P6 3 /m, a=1.63900(3) nm, c=0.37573(1) nm, Z=1, R F =0.062 for 1574 F-values and 74 variable parameters), and for Er 13 Ni 25 As 19 (Tm 13 Ni 25 As 19 -type structure, space group P6-bar , a=1.6208(1) nm, c=0.38847(2) nm, Z=1, R F =0.026 for 1549 F-values and 116 variable parameters). These compounds belong to a large family of hexagonal structures with a metal-metalloid ratio of 2:1. HRTEM investigations were conducted to probe for local ordering of the disordered structure at the nanoscale. The magnetic properties of the phosphide Er 12 Ni 30 P 21 have been studied in the temperature of range 2 eff =9.59 μ B corresponds to the theoretical value of Er 3+ . - Graphical abstract: The new ternary pnictides Er 12 Ni 30 P 21 and Er 13 Ni 25 As 19 have been synthesized from the elements. They crystallize with hexagonal structures determined from single-crystal X-ray data. The compounds belong to a large family of structures with a metal-metalloid ratio of 2:1. HRTEM investigations were conducted to probe for local ordering of the disordered structure at the nanoscale. Display Omitted

Study of vibrational and magnetic excitations in Ni sub c Mg sub 1 sub - sub c O solid solutions by Raman spectroscopy

CERN Document Server

Cazzanelli, E; Mariotto, G; Mironova-Ulmane, N

2003-01-01

The Raman scattering by phonons and magnons was studied for the first time in the polycrystalline solid solutions Ni sub c Mg sub 1 sub - sub c O. The experimental Raman spectrum for c = 0.9 is similar to that of NiO and consists of six well resolved bands, whose origins are the disorder-induced one-phonon scattering (bands at 400 and 500 cm sup - sup 1), two-phonon scattering (bands at 750, 900, and 1100 cm sup - sup 1), and two-magnon scattering (the broad band at approx 1400 cm sup - sup 1). We found that the dependence of the two-magnon band in solid solutions on the composition and temperature is consistent with their magnetic phase diagram. We also observed that the relative contribution of two-phonon scattering decreases strongly upon dilution with magnesium ions and disappears completely at c < 0.5. Such behaviour is explained in terms of a disorder-induced effect, which increases the probability of the one-phonon scattering processes.

Ternary systems Sr-{Ni,Cu}-Si: Phase equilibria and crystal structure of ternary phases

International Nuclear Information System (INIS)

Nasir, Navida; Melnychenko-Koblyuk, Nataliya; Grytsiv, Andriy; Rogl, Peter; Giester, Gerald; Wosik, Jaroslaw; Nauer, Gerhard E.

2010-01-01

Phase relations were established in the Sr-poor part of the ternary systems Sr-Ni-Si (900 deg. C) and Sr-Cu-Si (800 deg. C) by light optical microscopy, electron probe microanalysis and X-ray diffraction on as cast and annealed alloys. Two new ternary compounds SrNiSi 3 (BaNiSn 3 -type) and SrNi 9-x Si 4+x (own-type) were found in the Sr-Ni-Si system along with previously reported Sr(Ni x Si 1-x ) 2 (AlB 2 -type). The crystal structure of SrNi 9-x Si 4+x (own-type, x=2.7, a=0.78998(3), c=1.1337(2) nm; space group P4/nbm) was determined from X-ray single crystal counter to be a low symmetry derivative of the cubic, parent NaZn 13 -type. At higher Si-content X-ray Rietveld refinements reveal the formation of a vacant site (□) corresponding to a formula SrNi 5.5 Si 6.5 □ 1.0 . Phase equilibria in the Sr-Cu-Si system are characterized by the compounds SrCu 2-x Si 2+x (ThCr 2 Si 2 -type), Sr(Cu x Si 1-x ) 2 (AlB 2 -type), SrCu 9-x Si 4+x (0≤x≤1.0; CeNi 8.5 Si 4.5 -type) and SrCu 13-x Si x (4≤x≤1.8; NaZn 13 -type). The latter two structure types appear within a continuous solid solution. Neither a type-I nor a type-IX clathrate compound was encountered in the Sr-{Cu,Ni}-Si systems. Structural details are furthermore given for about 14 new ternary compounds from related alloy systems with Ba. - Graphical abstract: The crystal structure of SrNi 9-x Si 4+x (own-type, x=2.7, a=0.78998(3), c=1.1337(2) nm; space group P4/nbm) was determined from X-ray single crystal counter to be a low symmetry derivative of the cubic, parent NaZn 13 -type and is related to CeNi 8.5 Si 4.5 -type.

Characterization of crystallization kinetics of a Ni- (Cr, Fe, Si, B, C, P) based amorphous brazing alloy by non-isothermal differential scanning calorimetry

International Nuclear Information System (INIS)

Raju, S.; Kumar, N.S. Arun; Jeyaganesh, B.; Mohandas, E.; Mudali, U. Kamachi

2007-01-01

The thermal stability and crystallization kinetics of a Ni- (Cr, Si, Fe, B, C, P) based amorphous brazing foil have been investigated by non-isothermal differential scanning calorimetry. The glass transition temperature T g , is found to be 720 ± 2 K. The amorphous alloy showed three distinct, yet considerably overlapping crystallization transformations with peak crystallization temperatures centered around 739, 778 and 853 ± 2 K, respectively. The solidus and liquidus temperatures are estimated to be 1250 and 1300 ± 2 K, respectively. The apparent activation energies for the three crystallization reactions have been determined using model free isoconversional methods. The typical values for the three crystallization reactions are: 334, 433 and 468 kJ mol -1 , respectively. The X-ray diffraction of the crystallized foil revealed the presence of following compounds Ni 3 B (Ni 4 B 3 ), CrB, B 2 Fe 15 Si 3 , CrSi 2 , and Ni 4.5 Si 2 B

Apparent and standard molar volumes and heat capacities of aqueous Ni(ClO4)2 from 25 to 85oC

International Nuclear Information System (INIS)

Pan, P.; Campbell, A.B.

1997-01-01

Apparent molar heat capacities and volumes of aqueous Ni(ClO 4 ) 2 were measured from 25 to 85 o C over a concentration range of 0.02 to 0.8 mol-kg -1 using a Picker flow microcalorimeter and a Picker vibrating-tube densimeter. An extended Debye-Huckel equation was fitted to the experimental data to obtain expressions for the apparent molar properties as functions of ionic strength for Ni(ClO 4 ) 2 (aq). The standard-state partial molar properties for Ni(ClO 4 ) 2 (aq) in the temperature range 25 to 85 o C were obtained and can be expressed by empirical equations. The standard partial molar heat capacities and volumes for Ni 2+ (aq) from 25 to 86 o C were obtained by using the additivity rule and data for ClO - 4 (aq) in the literature. These values were extrapolated to 300 o C by employing the Helgeson-Kirkham-Flower (HKF) equations, amended to include a standard-state correction term. (author)

Hydrogen diffusion in La1.5Nd0.5MgNi9 alloy electrodes of the Ni/MH battery

International Nuclear Information System (INIS)

Volodin, A.A.; Denys, R.V.; Tsirlina, G.A.; Tarasov, B.P.; Fichtner, M.; Yartys, V.A.

2015-01-01

Highlights: • Hydrogen diffusion in the La 1.5 Nd 0.5 MgNi 9 alloy electrode was studied. • Various techniques of low amplitude potentiostatic data treatment were used. • D H demonstrates a maximum (2 × 10 −11 cm 2 /s) at 85% of discharge of the electrode. • Maximum is associated with a conversion of β-hydride into a solid α-solution. • Optimization of material and electrode will allow high discharge rates. - Abstract: Hydrogen diffusion in the La 1.5 Nd 0.5 MgNi 9 battery electrode material has been studied using low amplitude potentiostatic experiments. Complex diffusion behavior is examined in frames of electroanalytical models proposed for the lithium intercalation materials. Hydrogen diffusion coefficient D H changes with hydrogen content in the metal hydride anode electrode and has a maximum of ca. 2 × 10 −11 cm 2 /s at ca. 85% of discharge. Such a behavior differs from the trends known for the transport in lithium battery materials, but qualitatively agrees with the data for the highly concentrated β-PdH x

Synthesis of renewable diesel through hydrodeoxygenation reaction from nyamplung oil (Calophyllum Inophyllum oil) using NiMo/Z and NiMo/C catalysts with rapid heating and cooling method

Science.gov (United States)

Susanto, B. H.; Prakasa, M. B.; Shahab, M. H.

2016-11-01

The synthesis of metal nanocrystal was conducted by modification preparation from simple heating method which heating and cooling process run rapidly. The result of NiMo/Z 575 °C characterizations are 33.73 m2/gram surface area and 31.80 nm crystal size. By used NiMo/C 700 °C catalyst for 30 minutes which had surface area of 263.21 m2/gram, had 31.77 nm crystal size, and good morphology, obtained catalyst with high activity, selectivity, and stability. After catalyst activated, synthesis of renewable diesel performed in hydrogenation reactor at 375 °C, 12 bar, and 800 rpm. The result of conversion was 81.99%, yield was 68.08%, and selectivity was 84.54%.

Theoretical Prediction on [5]Radialene Sandwich Complexes (CpM)2(C10H10) (Cp = η5-C5H5; M = Fe, Co, Ni): Geometry, Spin States, and Bonding.

Science.gov (United States)

Liu, Nan-Nan; Xue, Ying-Ying; Ding, Yi-Hong

2017-02-09

[5]Radialene, the missing link for synthesis of radialene family, has been finally obtained via the preparation and decomplexation of the [5]radialene-bis-Fe(CO) 3 complex. The stability of [5]radialene complex benefits from the coordination with Fe(CO) 3 by losing free 1,3-butadiene structures to avoid polymerization. In light of the similar coordination ability of half-sandwiches CpM(Cp = η 5 -C 5 H 5 ; M = Fe, Co, Ni), there is a great possibility that the sandwiched complexes of [5]radialene with CpM are available. Herein, we present the first theoretical prediction on the geometry, spin states and bonding of (CpM)(C 10 H 10 ) and (CpM) 2 (C 10 H 10 ). For M = Fe, Co, Ni, the ground states of (CpM)(C 10 H 10 ) and (CpM) 2 (C 10 H 10 ) are doublet and triplet, singlet and singlet, and doublet and triplet states, where each Fe, Co, and Ni adopts 17, 18, and 19 electron-configuration, respectively. In particular, (CpFe) 2 (C 10 H 10 ) and (CpNi) 2 (C 10 H 10 ) have considerable open-shell singlet features. Generally the trans isomers of (CpM) 2 (C 10 H 10 ) with two CpM fragments on the opposite sides of the [5]radialene plane are apparently more stable than the cis ones with CpM fragments on the same side. However, for the singlet and triplet isomers of (CpNi) 2 (C 10 H 10 ) (both cis and trans isomers), the energy differences are relatively small, indicating that these isomers all have the opportunity to exist. Besides, the easy Diels-Alder (DA) dimerization between the [3]dendralene-like fragments of (CpM)(C 10 H 10 ) suggests the great difficulty in isolating the (CpM)(C 10 H 10 ) monomer.

Evaporation residue cross sections and average neutron multiplicities in the /sup 64/Ni+/sup 92/Zr and /sup 12/C+/sup 144/Sm reactions leading to /sup 156/Er

Energy Technology Data Exchange (ETDEWEB)

Janssens, R.V.F.; Holzmann, R.; Henning, W.; Khoo, T.L.; Lesko, K.T.; Stephans, G.S.F.; Radford, D.C.; Van den Berg, A.M.; Kuehn, W.; Ronningen, R.M.

1986-11-27

Evaporation residue cross sections and neutron multiplicity distributions have been measured for the /sup 12/C+/sup 144/Sm and /sup 64/Ni+/sup 92/Zr reactions leading to the same compound nucleous /sup 156/Er. Statistical model calculations can account for the data in the /sup 12/C-induced reaction. In contrast, the inhibition of neutron emission with respect to statistical model predictions seen in /sup 64/Ni+/sup 92/Zr cannot be explained even with the inclusion of the broad angular momentum distributions required to describe the fusion cross section data.

Explosive anisotropic grain growth of delta-NiMo by solid-state diffusion

International Nuclear Information System (INIS)

Chou, T.C.; Nieh, T.G.

1991-01-01

Anomalous, anisotropic grain growth has been observed in delta(δ)-NiMo intermetallic compound during the annealings of Mo/Ni thin-film diffusion couples at 700 and 800 degree C. Two layered microstructures showing median-sized, equiaxed grains and large columnar single crystalline grains were generated. The growth direction of the columnar grains was parallel to the direction of Ni diffusion flux. Electron diffraction indicated that both the median-sized and the columnar grains were δ-NiMo. The composition of δ-NiMo was determined to be Ni48-Mo52 (at.%). According to the thickness of reaction-formed δ-NiMo, the apparent interdiffusion coefficient was measured to be about 10 -10 cm 2 /s which is 4 to 5 orders of magnitude greater than literature data. The enhanced diffusion rate in Ni-Mo, and the anomalous anisotropic grain growth of δ-NiMo compound are discussed on the basis of exothermic reactions between Ni and Mo during diffusional intermixing. The enthalpy of the formation of δ-NiMo is calculated and demonstrated to be sufficient to cause melting/solidification of the compound

Development of a flat-field spectrometer with a wideband Ni/C multilayer grating in the 1–3.5 keV range

Energy Technology Data Exchange (ETDEWEB)

Imazono, Takashi [Quantum Beam Science Center, Japan Atomic Energy Agency, 8-1-7, Umemidai, Kizugawa, Kyoto 619-0216 (Japan)

2016-07-27

To develop a flat-field spectrometer with coverage of the 1–3.5 keV range, a wideband Ni/C multilayer grating was invented. The multilayer consists of two kinds of layer structures. One is a conventional periodic multilayer of thickness D{sub 1} = 5.6 nm, Ni thickness ratio to the multilayer period γ{sub 1} = 0.5 and the number of layers N{sub 1} = 79. Both the first and last layers are Ni. The other is a C/Ni bilayer of D{sub 2} = 8.4 nm, γ{sub 2} = 0.53 and N{sub 2} = 2. The first layer is C and then Ni. The aperiodic multilayer from the topmost C/Ni bilayer was coated on a laminar-type grating having an effective grating constant of 1/2400 mm, groove depth of 2.8 nm, and duty ratio (land width/groove period) of 0.5. In a preliminary experiment, the diffraction efficiency was in excess of 0.8% in the energy range of 2.1-3.3 keV and the maximum of 5.4% at 3.1 keV at a constant angle of incidence of 88.54°, which is considerably higher than that of an Au-coated grating before deposition of the multilayer.

Synthesis and optical characterization of C-SiO2 and C-NiO sol-gel composite films for use as selective solar absorbers

CSIR Research Space (South Africa)

Makiwa, G

2008-08-01

Full Text Available The authors present a cheaper and environmentally friendly method to fabricate efficient spectrally selective solar absorber materials. The sol-gel technique was used to fabricate carbon-silica (C-SiO2) and carbon-nickel oxide (C-NiO) composite...

Enhanced photocatalytic efficiency in zirconia buffered n-NiO/p-NiO single crystalline heterostructures by nanosecond laser treatment

Energy Technology Data Exchange (ETDEWEB)

Molaei, R.; Bayati, M. R.; Alipour, H. M.; Nori, S.; Narayan, J. [Department of Materials Science and Engineering, NC State University, EB-1, Raleigh, North Carolina 27695-7907 (United States)

2013-06-21

We report the formation of NiO based single crystalline p-n junctions with enhanced photocatalytic activity induced by pulsed laser irradiation. The NiO epilayers were grown on Si(001) substrates buffered with cubic yttria-stabilized zirconia (c-YSZ) by using pulsed laser deposition. The NiO/c-YSZ/Si heterostructures were subsequently laser treated by 5 pulses of KrF excimer laser (pulse duration = 25 Multiplication-Sign 10{sup -9} s) at lower energies. Microstructural studies, conducted by X-ray diffraction ({theta}-2{theta} and {phi} techniques) and high resolution transmission electron microscope, showed a cube-on-cube epitaxial relationship at the c-YSZ/Si interface; the epitaxial relationship across the NiO/c-YSZ interface was established as NiO<111 > Double-Vertical-Line Double-Vertical-Line c-YSZ<001> and in-plane NiO<110> Double-Vertical-Line Double-Vertical-Line c-YSZ<100>. Electron microscopy studies showed that the interface between the laser annealed and the pristine region as well as the NiO/c-YSZ interface was atomically sharp and crystallographically continuous. The formation of point defects, namely oxygen vacancies and NiO, due to the coupling of the laser photons with the NiO epilayers was confirmed by XPS. The p-type electrical characteristics of the pristine NiO epilayers turned to an n-type behavior and the electrical conductivity was increased by one order of magnitude after laser treatment. Photocatalytic activity of the pristine (p-NiO/c-YSZ/Si) and the laser-annealed (n-NiO/p-NiO/c-YSZ/Si) heterostructures were assessed by measuring the decomposition rate of 4-chlorophenol under UV light. The photocatalytic reaction rate constants were determined to be 0.0059 and 0.0092 min{sup -1} for the as-deposited and the laser-treated samples, respectively. The enhanced photocatalytic efficiency was attributed to the suppressed charge carrier recombination in the NiO based p-n junctions and higher electrical conductivity. Besides, the oxygen vacancies

The interplay of magnetic order and superconductivity in GdxY1-xNi2B2C

International Nuclear Information System (INIS)

Drzazga, Z.; Fuchs, G.; Handstein, A.; Nenkov, K.; Mueller, K.-H.

2003-01-01

Resistivity, ac susceptibility and magnetization measurements are reported for polycrystalline samples of the Gd x Y 1-x Ni 2 B 2 C series as a function of temperature and magnetic field. The magnetic Gd impurities cause an almost linear decrease of the superconducting transition temperature T c with increasing Gd content in the range of x c have been observed. The effect of the 4f local moments manifests in a complete suppression of superconductivity for x≥0.3 and in antiferromagnetic ordering for x>0.3. In zero applied magnetic field, a distinct concentration region around x∼0.3 has been revealed separating superconductivity and antiferromagneting ordering. A metamagnetic transition has been observed in the compound with x=0.5 at a magnetic field of 0.8 T

Interplay between magnetism and superconductivity in HoNi2B2C revisited

Science.gov (United States)

Alleno, E.; Singh, S.; Dhar, S. K.; André, G.

2010-04-01

In this work the magnetic and superconducting properties of HoNi2B2C were investigated by using powder neutron diffraction and the specific heat and upper critical field (Hc2) measurements as a function of temperature. Below T=8 K, three distinct anomalies at the temperatures TN=5.2 K, TH1=5.6 K and TM=6.0 K were observed in the specific heat of HoNi2B2C, as reported in the literature. Our neutron data confirm the transitions to the Néel structure (qN=c*) at TN and to the modulated structure (qM=0.586a*) at TM. The peak at TH1=5.7 K in the specific heat data, whose exact nature was not known hitherto, is now attributed to the onset of a qH1=0.905c* magnetic helical structure as seen in our neutron data. Comparison between the thermal evolution of the magnetic structures and the temperature dependence of the upper critical field confirms that the first Hc2(T) depression at 6.1 K arises from the qM=0.586a* modulated magnetic structure. The second depression in Hc2(T) below 5.7 K can be ascribed to the qH1=0.905c* magnetic helical structure.

Crystal structures and magnetic properties of iron (III)-based phosphates: Na{sub 4}NiFe(PO{sub 4}){sub 3} and Na{sub 2}Ni{sub 2}Fe(PO{sub 4}){sub 3}

Energy Technology Data Exchange (ETDEWEB)

Essehli, Rachid, E-mail: rachid_essehli@yahoo.fr [Laboratory of Mineral Solid and Analytical Chemistry ' LCSMA' , Department of Chemistry, Faculty of Sciences, University Mohamed I, Po. Box 717, 60000 Oujda (Morocco); Bali, Brahim El [Laboratory of Mineral Solid and Analytical Chemistry ' LCSMA' , Department of Chemistry, Faculty of Sciences, University Mohamed I, Po. Box 717, 60000 Oujda (Morocco); Benmokhtar, Said [LCMS, Laboratoire de Chimie des Materiaux Solides, Departement de chimie, Faculte des Sciences Ben M' SIK, Casablanca (Morocco); Bouziane, Khalid [Physics Department, College of Science, Sultan Qaboos University, PO Box 36, Postal Code 123 Al Khod, Sultanate of Oman (Oman); Manoun, Bouchaib [Laboratoire de Physico-Chimie des Materiaux, Departement de Chimie, FST Errachidia, University Moulay Ismail, B.P. 509 Boutalamine, Errachidia (Morocco); Abdalslam, Mouner Ahmed [Materials Science, Technical University Darmstadt, Darmstadt (Germany); Ehrenberg, Helmut [IFW Dresden, Helmholtzstr. 20, D-01069 Dresden (Germany)

2011-01-28

Graphical abstract: A perspective view of the Na{sub 2}Ni{sub 2}Fe(PO{sub 4}){sub 3} structure along the [0 0 1] direction. Both compounds seem to exibit antiferromagnetic interactions between magnetic entities at low temperature. Display Omitted Research highlights: > Nasicon and Alluaudite compounds, Iron(III)-based phosphates, Crystal structures of Na{sub 4}NiFe(PO{sub 4}){sub 3} and Na{sub 2}Ni{sub 2}Fe(PO{sub 4}){sub 3}. > Magnetism behaviours of Na{sub 4}NiFe(PO{sub 4}){sub 3} and Na{sub 2}Ni{sub 2}Fe(PO{sub 4}){sub 3}. > Antiferromagnetism interactions. > Mossbauer spectroscopy. - Abstract: Crystal structures from two new phosphates Na{sub 4}NiFe(PO{sub 4}){sub 3} (I) and Na{sub 2}Ni{sub 2}Fe(PO{sub 4}){sub 3} (II) have been determined by single crystal X-ray diffraction analysis. Compound (I) crystallizes in a rhombohedral system (S. G: R-3c, Z = 6, a = 8.7350(9) A, c = 21.643(4) A, R{sub 1} = 0.041, wR{sub 2}=0.120). Compound (II) crystallizes in a monoclinic system (S. G: C2/c, Z = 4, a = 11.729(7) A, b = 12.433(5) A, c = 6.431(2) A, {beta} = 113.66(4){sup o}, R{sub 1} = 0.043, wR{sub 2}=0.111). The three-dimensional structure of (I) is closely related to the Nasicon structural type, consisting of corner sharing [(Ni/Fe)O{sub 6}] octahedra and [PO{sub 4}] tetrahedra forming [NiFe(PO{sub 4}){sub 3}]{sup 4+} units which align in chains along the c-axis. The Na{sup +} cations fill up trigonal antiprismatic sites within these chains. The crystal structure of (II) belongs to the alluaudite type. Its open framework results from [Ni{sub 2}O{sub 10}] units of edge-sharing [NiO{sub 6}] octahedra, which alternate with [FeO{sub 6}] octahedra that form infinite chains. Coordination of these chains yields two distinct tunnels in which site Na{sup +}. The magnetization data of compound (I) reveal antiferromagnetic (AFM) interactions by the onset of deviations from a Curie-Weiss behaviour at low temperature as confirmed by Moessbauer measurements performed at 4.2 K. The

The Deoxygenation Pathways of Palmitic Acid into Hydrocarbons on Silica-Supported Ni12P5 and Ni2P Catalysts

Directory of Open Access Journals (Sweden)

Wenjun Zhou

2018-04-01

Full Text Available Pure Ni12P5/SiO2 and pure Ni2P/SiO2 catalysts were obtained by adjusting the Ni and P molar ratios, while Ni/SiO2 catalyst was prepared as a reference against which the deoxygenation pathways of palmitic acid were investigated. The catalysts were characterized by N2 adsorption, X-ray diffraction (XRD, X-ray photoelectron spectroscopy (XPS, transmission election microscopy (TEM, infrared spectroscopy of pyridine adsorption (Py-IR, H2-adsorption and temperature-programmed desorption of hydrogen (H2-TPD. The crystallographic planes of Ni(111, Ni12P5(400, Ni2P(111 were found mainly exposed on the above three catalysts, respectively. It was found that the deoxygenation pathway of palmitic acid mainly proceeded via direct decarboxylation (DCO2 to form C15 on Ni/SiO2. In contrast, on the Ni12P5/SiO2 catalyst, there were two main competitive pathways producing C15 and C16, one of which mainly proceeded via the decarbonylation (DCO to form C15 accompanying water formation, and the other pathway produced C16 via the dehydration of hexadecanol intermediate, and the yield of C15 was approximately twofold that of C16. Over the Ni2P/SiO2 catalyst, two main deoxygenation pathways formed C15, one of which was mainly the DCO pathway and the other was dehydration accompanying the hexadecanal intermediate and then direct decarbonylation without water formation. The turn over frequency (TOF followed the order: Ni12P5/SiO2 > Ni/SiO2 > Ni2P/SiO2.

Electrochemical Properties of Hydrogen-Storage Alloys ZrMn{sub 2}Ni{sub x} and ZrMnNi{sub 1+x} for Ni-MH Secondary Battery

Energy Technology Data Exchange (ETDEWEB)

Park, Hye Ryoung [Faculty of Applied Chemistry, Chonnam National University, Kwangju (Korea); Kwon, Ik Hyun [Automobile High-Technology Research Institute, Division of Advanced Materials Engineering, Chonbuk National University, Chonju (Korea)

2001-04-01

In order to improve the performance of AB{sub 2}-type hydrogen-storage alloys for Ni-MH secondary battery, AB{sub 2}-type alloys, ZrMn{sub 2}Ni{sub x}(x=0.0, 0.3, 0.6, 0.9 and 1.2) and ZrMnNi{sub 1+x}(x=0.0, 0.1, 0.2, 0.3 and 0.4) were prepared as the Zr-Mn-Ni three component alloys. The hydrogen-storage and the electrochemical properties were investigated. The C14 Laves phase formed in all alloys of ZrMn{sub 2}Ni{sub x}(x=0.0 {approx} 1.2). The equilibrium plateau pressure of the alloy, ZrMn{sub 2}Ni{sub 0.6}-H{sub 2} system, was about 0.5 atm at 30 degree C. Among these alloys, ZrMn{sub 2}Ni{sub 0.6} was the easiest to activate, and it had the largest discharge capacity as well as the best cycling performance. The C14 Laves phase also formed in all alloys of ZrMnNi{sub 1+x}(x=0.0 {approx} 0.4). The equilibrium plateau pressure of the alloy, ZrMnNi{sub 1.0}-H{sub 2} system, was about 0.45 atm at 30 degree C. Among these alloys, ZrMnNi{sub 1.0} was the easiest to activate, taking only 3 charge-discharge cycles, and it had the largest discharge capacity of 42 mAh/g. Among these alloys, ZrMn{sub 2}Ni{sub x}(x=0.0 {approx} 1.2) and ZrMnNi{sub 1+x}(x=0.0 {approx} 0.4), ZrMnNi{sub 1.0} had the largest discharge capacity (maximum value of 42 mAh/g), and it showed the fastest activation and good cycling performance. 23 refs., 4 figs., 2 tabs.

Pitting Corrosion of Ni3(Si,Ti+2Cr Intermetallic Compound at Various Chloride Concentrations

Directory of Open Access Journals (Sweden)

Gadang Priyotomo

2014-05-01

Full Text Available The pitting corrosion of Ni3(Si,Ti with 2 at% Cr containing two regions of a Ni3(Si,Ti single-phase of L12 structure and a mixture phase of of (L12 +Niss was investigated as function of chloride concentrations by using a polarization method, scanning electron microscope and energy dispersive X-Ray spectroscopy in neutral sodium chloride solutions at 293 K.  The pitting corrosion of Ni3(Si,Ti with and without the addition of aluminium and type C276 alloy were also studied under the same experimental condition for the comparison.  The pitting potential obtained for the Ni3(Si,Ti with 2 at% Cr decreased with increasing chloride concentration.  The specific pitting potentials and the pitting potentials were decreased in the order of C276 alloy > Ni3(Si,Ti > Ni3(Si,Ti + 2Cr > Ni3(Si,Ti + 4Al, which means that the pitting corrosion resistance of Ni3(Si,Ti with 2 at% Cr was higher than Ni3(Si,Ti with 4 at% Al, but lower than that of Ni3(Si,Ti.  A critical chloride concentration of Ni3(Si,Ti with 2 at% Cr was found to be higher than that of Ni3(Si,Ti with at% Al. In addition, the presence of high concentration for oxygen indicates the occurrence of pit formation.

Effect of consolidation techniques on the properties of Al matrix composite reinforced with nano Ni-coated SiC

Science.gov (United States)

Abolkassem, Shimaa A.; Elkady, Omayma A.; Elsayed, Ayman H.; Hussein, Walaa A.; Yehya, Hosam M.

2018-06-01

Al /Ni-SiC composite was prepared via powder metallurgy technique. SiC particles were coated with 10 wt% nano nickel by electroless deposition, then mixed by three percents (5, 10 and 15 wt%) with Al powder in a ball mill using 10:1 ball to powder ratio for 5 h. Three types of sintering techniques were used to prepare the composite. Uniaxial cold compacted samples were sintered in a vacuum furnace at 600 °C for 1 h. The second group was the vacuum sintered samples which were post-processed by hot isostatic press (HIP) at 600 °C for 1hr under the pressure of 190 MPa. The third group was the hot pressed samples that were consolidated at 550 °C under the uniaxial pressure of 840 MPa. The results showed that the hot pressed samples have the highest densification values (97-100%), followed by the HIP samples (94-98%), then come the vacuum sintered ones (92-96%). X-ray diffraction analysis (XRD) indicated the presence of Al and Al3Ni, which means that all SiC particles were encapsulated with nickel as short peaks for SiC were observed. Hardness results revealed that HIP samples have the highest hardness values. The magnetization properties were improved by increasing SiC/Ni percent, and HIP samples showed the highest magnetization parameter values.

Optimisation of optical absorption properties of spectrally selective C-NiO composite coatings

CSIR Research Space (South Africa)

Tile, N

2011-05-01

Full Text Available and expensive. Carbon in Nickel Oxide (C-NiO) composite material has been found to have a very good spectral selectivity1,2. Moreover this material has a potential of low cost large scale fabrication since it can be fabricated by a simple sol-gel technique...

The creep and intergranular cracking behavior of Ni-Cr-Fe-C alloys in 360 degree C water

International Nuclear Information System (INIS)

Angeliu, T.M.; Paraventi, D.J.; Was, G.S.

1995-01-01

Mechanical testing of controlled-purity Ni-xCr-9Fe-yC alloys at 360 C revealed an environmental enhancement in IG cracking and time-dependent deformation in high purity and primary water over that exhibited in argon. Dimples on the IG facets indicate a creep void nucleation and growth failure mode. IG cracking was primarily located at the interior of the specimen and not necessarily linked to direct contact with the environment. Controlled potential CERT experiments showed increases in IG cracking as the applied potential decreased, suggesting that hydrogen is detrimental to the mechanical properties. It is proposed that the environment, through the presence of hydrogen, enhances IG cracking by enhancing the matrix dislocation mobility. This is based on observations that dislocation-controlled creep controls the IG cracking of controlled-purity Ni-xCr-9Fe-yC in argon at 360 C and grain boundary cavitation and sliding results that show the environmental enhancement of the creep rate is primarily due to an increase in matrix plastic deformation. However, controlled potential CLT experiments did not exhibit a change in the creep rate as the applied potential decreased. While this does not clearly support hydrogen assisted creep, the material may already be saturated with hydrogen at these applied potentials and thus no effect was realized. Chromium and carbon decrease the IG cracking in high purity and primary water by increasing the creep resistance. The surface film does not play a significant role in the creep or IG cracking behavior under the conditions investigated