WorldWideScience

Sample records for composite edible coating

  1. Gum arabic based composite edible coating on green chillies

    Science.gov (United States)

    Valiathan, Sreejit; Athmaselvi, K. A.

    2018-04-01

    Green chillies were coated with a composite edible coating composed of gum arabic (5%), glycerol (1%), thyme oil (0.5%) and tween 80 (0.05%) to preserve the freshness and quality of green chillies and thus reduce the cost of preservation. In the present work, the chillies were coated with the composite edible coating using the dipping method with three dipping times (1, 3 and 5 min). The physicochemical parameters of the coated and control chillies stored at room temperature (28±2ºC) were evaluated at regular intervals of storage. There was a significant difference (p≤0.05) in the physicochemical properties between the control chillies and coated chillies with 1, 3 and 5 min dipping times. The coated green chillies showed significantly (p≤0.05) lower weight loss, phenolic acid production, capsaicin production and significantly (p≤0.05) higher retention of ascorbic acid, total chlorophyll content, colour, firmness and better organoleptic properties. The composite edible coating of gum arabic and thyme oil with 3 min dipping was effective in preserving the desirable physico-chemical and organoleptic properties of the green chillies up to 12 days, compared to the uncoated chillies that had a shelf life of 6 days at room temperature.

  2. Delayed post-harvest ripening-associated changes in Manilkara zapota L. var. Kalipatti with composite edible coating.

    Science.gov (United States)

    Vishwasrao, Chandrahas; Ananthanarayan, Laxmi

    2017-01-01

    There has been limited research on extending the shelf-life of sapota (Manilkara zapota L. var. Kalipatti) fruit. An edible coating made up of methyl cellulose (MC) and palm oil (PO) was applied to study the extension in shelf-life. Changes in physical and chemical properties of fruit were studied along with peroxidase (POD), polyphenol oxidase (PPO) and pectin methylesterase (PME) activities during post-harvest ripening of sapota. The fruits coated with 15 g L -1 MC and 11.25 g L -1 PO showed significant (P edible coating made up of MC-PO has potential to maintain the quality of sapota fruit. The edible coating extended the shelf-life of sapota fruit by 3 days preserving fruit quality up to 7 days at 24 ± 1 °C and 65 ± 5 %RH. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

  3. Effect of Hydroxypropyl Methylcellulose-Beeswax Composite Edible Coatings Formulated with or without Antifungal Agents on Physicochemical Properties of Plums during Cold Storage

    Directory of Open Access Journals (Sweden)

    Sule Gunaydin

    2017-01-01

    Full Text Available The influence of hydroxypropyl methylcellulose- (HPMC- beeswax (BW composite edible coatings formulated with or without food additives with antifungal properties on physicochemical and sensory properties of plums (Prunus salicina cv. “Friar” stored for 11 and 22 d at 1°C followed by a shelf life period of 5 d at 20°C was evaluated. Food preservatives selected from previous research included potassium sorbate (PS, sodium methyl paraben (SMP, and sodium ethyl paraben (SEP. Emulsions had 7% of total solid content and were prepared with glycerol and stearic acid as plasticizer and emulsifier, respectively. All the coatings reduced plum weight and firmness loss and coated fruit showed higher titratable acidity, soluble solids content, and hue angle values at the end of the storage period. In addition, physiological disorders such as flesh browning and bleeding were reduced in coated samples compared to uncoated controls. Paraben-based coatings were the most effective in controlling weight loss and the SMP-based coating was the most effective in maintaining plum firmness. Respiration rate, sensory flavor, off-flavors, and fruit appearance were not adversely affected by the application of antifungal coatings. Overall, these results demonstrated the potential of selected edible coatings containing antifungal food additives to extend the postharvest life of plums, although further studies should focus on improving some properties of the coatings to enhance gas barrier properties and further increase storability.

  4. Advances in edible coatings for fresh fruits and vegetables: a review.

    Science.gov (United States)

    Dhall, R K

    2013-01-01

    Edible coatings are an environmentally friendly technology that is applied on many products to control moisture transfer, gas exchange or oxidation processes. Edible coatings can provide an additional protective coating to produce and can also give the same effect as modified atmosphere storage in modifying internal gas composition. One major advantage of using edible films and coatings is that several active ingredients can be incorporated into the polymer matrix and consumed with the food, thus enhancing safety or even nutritional and sensory attributes. But, in some cases, edible coatings were not successful. The success of edible coatings for fresh products totally depends on the control of internal gas composition. Quality criteria for fruits and vegetables coated with edible films must be determined carefully and the quality parameters must be monitored throughout the storage period. Color change, firmness loss, ethanol fermentation, decay ratio and weight loss of edible film coated fruits need to be monitored. This review discusses the use of different edible coatings (polysaccharides, proteins, lipids and composite) as carriers of functional ingredients on fresh fruits and vegetables to maximize their quality and shelf life. This also includes the recent advances in the incorporation of antimicrobials, texture enhancers and nutraceuticals to improve quality and functionality of fresh-cut fruits. Sensory implications, regulatory status and future trends are also reviewed.

  5. Application of edible coating with essential oil in food preservation.

    Science.gov (United States)

    Ju, Jian; Xie, Yunfei; Guo, Yahui; Cheng, Yuliang; Qian, He; Yao, Weirong

    2018-03-26

    Compared with other types of packaging, edible coatings are becoming more and more popular because of their more environmentally friendly properties and active ingredients carrying ability. The edible coating can reduce the influence of essential oils (EOs) on the flavor of the product and also can prolong the action time of EOs through the slow-release effect, which effectively promote the application of EOs in food. Understanding the different combinations of edible coatings and EOs as well as their antimicrobial effects on different microorganisms will be more powerful and targeted to promote the application of EOs in real food systems. The review focus on the contribution of the combination of EOs and edible coatings (EO-edible coatings) to prolong the shelf life of food products, (1) specifically addressing the main materials used in the preparation of EO-edible coatings and the application of EO-edible coatings in the product, (2) systematically summarizing the main production method of EO-edible coatings, (3) discussing the antiseptic activity of EO-edible coatings on different microorganisms in food.

  6. Effect of gamma irradiation in presence of ascorbic acid on microbial composition and TBARS concentration of ground beef coated with an edible active coating

    International Nuclear Information System (INIS)

    Lacroix, M.; Ouattara, B.; Saucier, L.; Giroux, M.; Smoragiewicz, W.

    2004-01-01

    The present study was conducted to evaluate the combined effect of gamma irradiation in presence of ascorbic acid on the microbiological characteristics and thiobarbituric acid-reactive substances (TBARS) concentration of ground beef coated with an edible coating, crosslinked by gamma irradiation. The medium fat ground beef patties (23% fat ) were divided into two separate treatment groups: (i) control (ground beef without additive), (ii) ground beef with 0.5% (w/w) ascorbic acid. Meat samples were irradiated at doses of 0, 1, 2, and 3 kGy and stored at 4±2 deg. C. The content of TBARS was evaluated. After 7 days of storage, Enterobacteriaceae, presumptive Staphylococcus aureus, presumptive Pseudomonas spp., Brochothrix thermosphacta and lactic acid bacteria were enumerated. Results showed that lactic acid bacteria and Br. thermosphacta were more resistant to irradiation than Enterobacteriaceae and Pseudomonas. The content in TBARS was stabilized during post-irradiation storage for samples containing ascorbic acid. Shelf life extension periods estimated on the basis of a limit level of 6 log CFU/g for APCs were 4, 7, and 10 days for samples irradiated at 1, 2, and 3 kGy, respectively. However, the incorporation of ascorbic acid in ground beef did not improve significantly (p>0.05) the inhibitory effect of gamma irradiation

  7. Effect of gamma irradiation in presence of ascorbic acid on microbial composition and TBARS concentration of ground beef coated with an edible active coating

    Energy Technology Data Exchange (ETDEWEB)

    Lacroix, M. E-mail: monique.lacroix@inrs-iaf.uquebec.ca; Ouattara, B.; Saucier, L.; Giroux, M.; Smoragiewicz, W

    2004-10-01

    The present study was conducted to evaluate the combined effect of gamma irradiation in presence of ascorbic acid on the microbiological characteristics and thiobarbituric acid-reactive substances (TBARS) concentration of ground beef coated with an edible coating, crosslinked by gamma irradiation. The medium fat ground beef patties (23% fat ) were divided into two separate treatment groups: (i) control (ground beef without additive), (ii) ground beef with 0.5% (w/w) ascorbic acid. Meat samples were irradiated at doses of 0, 1, 2, and 3 kGy and stored at 4{+-}2 deg. C. The content of TBARS was evaluated. After 7 days of storage, Enterobacteriaceae, presumptive Staphylococcus aureus, presumptive Pseudomonas spp., Brochothrix thermosphacta and lactic acid bacteria were enumerated. Results showed that lactic acid bacteria and Br. thermosphacta were more resistant to irradiation than Enterobacteriaceae and Pseudomonas. The content in TBARS was stabilized during post-irradiation storage for samples containing ascorbic acid. Shelf life extension periods estimated on the basis of a limit level of 6 log CFU/g for APCs were 4, 7, and 10 days for samples irradiated at 1, 2, and 3 kGy, respectively. However, the incorporation of ascorbic acid in ground beef did not improve significantly (p>0.05) the inhibitory effect of gamma irradiation.

  8. The characterization of edible coating from tilapia surimi as a biodegradable packaging

    Science.gov (United States)

    Saputra, E.; Alamsjah, A.; Abdillah, A. A.

    2018-04-01

    One of the problems that often arise in the fisheries sector is maintaining the quality. In the room temperature, the fish more quickly enter the phase of rigor mortis and lasted shorter. The retention of fresh fish can be extended by adding antibacterial compounds in the form of synthetic chemicals or natural ingredients. One of the safe natural ingredients used to extend the freshness of the fish is the edible coating. Edible coatings may be composed of hydrocolloid, lipids and composites. In the food industry surimi can be used as an ingredient to make edible packaging or better known in the form of edible film and protein-based edible coating. Edible film and potential coatings are used as packaging materials as they may affect food quality, food safety, and shelf life. Protein-based edible film have superior inhibitory and mechanical properties compared to polysaccharide-based ones. This is because protein contains 20 different amino acids and has most special characteristics that produce functional characteristics when compared with polysaccharides used as an ingredient in edible film and coating making most homopolymers.

  9. Evaluating food additives as antifungal agents against Monilinia fructicola in vitro and in hydroxypropyl methylcellulose-lipid composite edible coatings for plums.

    Science.gov (United States)

    Karaca, Hakan; Pérez-Gago, María B; Taberner, Verònica; Palou, Lluís

    2014-06-02

    Common food preservative agents were evaluated in in vitro tests for their antifungal activity against Monilinia fructicola, the most economically important pathogen causing postharvest disease of stone fruits. Radial mycelial growth was measured in Petri dishes of PDA amended with three different concentrations of the agents (0.01-0.2%, v/v) after 7 days of incubation at 25 °C. Thirteen out of fifteen agents tested completely inhibited the radial growth of the fungus at various concentrations. Among them, ammonium carbonate, ammonium bicarbonate and sodium bicarbonate were the most effective while sodium acetate and sodium formate were the least effective. The effective agents and concentrations were tested as ingredients of hydroxypropyl methylcellulose (HPMC)-lipid edible coatings against brown rot disease on plums previously inoculated with M. fructicola (curative activity). 'Friar' and 'Larry Ann' plums were inoculated with the pathogen, coated with stable edible coatings about 24h later, and incubated at 20 °C and 90% RH. Disease incidence (%) and severity (lesion diameter) were determined after 4, 6, and 8 days of incubation and the 'area under the disease progress stairs' (AUDPS) was calculated. Coatings containing bicarbonates and parabens significantly reduced brown rot incidence in plums, but potassium sorbate, used at 1.0% in the coating formulation, was the most effective agent with a reduction rate of 28.6%. All the tested coatings reduced disease severity to some extent, but coatings containing 0.1% sodium methylparaben or sodium ethylparaben or 0.2% ammonium carbonate or ammonium bicarbonate were superior to the rest, with reduction rates of 45-50%. Overall, the results showed that most of the agents tested in this study had significant antimicrobial activity against M. fructicola and the application of selected antifungal edible coatings is a promising alternative for the control of postharvest brown rot in plums. Copyright © 2014 Elsevier B

  10. Antimicrobial edible films and coatings for fresh and minimally processed fruits and vegetables: a review.

    Science.gov (United States)

    Valencia-Chamorro, Silvia A; Palou, Lluís; Del Río, Miguel A; Pérez-Gago, María B

    2011-01-01

    The use of edible films and coatings is an environmentally friendly technology that offers substantial advantages for shelf-life increase of many food products including fruits and vegetables. The development of new natural edible films and coatings with the addition of antimicrobial compounds to preserve fresh and minimally processed fruits and vegetables is a technological challenge for the industry and a very active research field worldwide. Antimicrobial agents have been successfully added to edible composite films and coatings based on polysaccharides or proteins such as starch, cellulose derivatives, chitosan, alginate, fruit puree, whey protein isolated, soy protein, egg albumen, wheat gluten, or sodium caseinate. This paper reviews the development of edible films and coatings with antimicrobial activity, typically through the incorporation of antimicrobial food additives as ingredients, the effect of these edible films on the control of target microorganisms, the influence of antimicrobial agents on mechanical and barrier properties of stand-alone edible films, and the effect of the application of antimicrobial edible coatings on the quality of fresh and fresh-cut fruits and vegetables.

  11. The Effect of Xanthan Gum and Flaxseed Mucilage as Edible Coatings in Cheddar Cheese during Ripening

    Directory of Open Access Journals (Sweden)

    Afshin Soleimani-Rambod

    2018-02-01

    Full Text Available The object of this study was to investigate the possibility of using xanthan gum and flaxseed mucilage as edible coatings for Cheddar cheese during ripening for 90 days. Five samples of Cheddar cheese blocks were coated with different coating materials in triplicate as follows: Coated with polyvinyl acetate as control (C, coated with 0.5% xanthan gum (XG, coated with 0.75% flaxseed mucilage (FM1, coated with 1% flaxseed mucilage (FM2, and coated with 1.25% flaxseed mucilage (FM3. All samples were kept at 8 ± 2 °C in a cold room for 90 days. The statistical analysis of the results showed that the moisture content of the samples decreased and the protein content increased during the ripening period (P < 0.01. The pH, acidity, fat in dry matter, and TCA-SN/TN of samples were significantly affected by xanthan gum and flaxseed mucilage treatment (P < 0.01. The free fatty acid composition of samples was significantly affected by edible coatings. Edible coatings affected the growth of non-starter lactic acid bacteria and the total mesophilic aerobic bacteria in a non-significant manner (P > 0.01. The growth of starter bacteria was significantly altered under the effect of edible coating materials (P < 0.05. Tyrosine and tryptophan contents as an index of proteolysis, lipolysis, and sensory evaluation of samples were not significantly different.

  12. Antifungal Edible Coatings for Fresh Citrus Fruit: A Review

    Directory of Open Access Journals (Sweden)

    Lluís Palou

    2015-12-01

    Full Text Available According to their origin, major postharvest losses of citrus fruit are caused by weight loss, fungal diseases, physiological disorders, and quarantine pests. Cold storage and postharvest treatments with conventional chemical fungicides, synthetic waxes, or combinations of them are commonly used to minimize postharvest losses. However, the repeated application of these treatments has led to important problems such as health and environmental issues associated with fungicide residues or waxes containing ammoniacal compounds, or the proliferation of resistant pathogenic fungal strains. There is, therefore, an increasing need to find non-polluting alternatives to be used as part of integrated disease management (IDM programs for preservation of fresh citrus fruit. Among them, the development of novel natural edible films and coatings with antimicrobial properties is a technological challenge for the industry and a very active research field worldwide. Chitosan and other edible coatings formulated by adding antifungal agents to composite emulsions based on polysaccharides or proteins and lipids are reviewed in this article. The most important antifungal ingredients are selected for their ability to control major citrus postharvest diseases like green and blue molds, caused by Penicillium digitatum and Penicillium italicum, respectively, and include low-toxicity or natural chemicals such as food additives, generally recognized as safe (GRAS compounds, plant extracts, or essential oils, and biological control agents such as some antagonistic strains of yeasts or bacteria.

  13. Tumeric oil as the antioxidation agent in edible coating film

    Science.gov (United States)

    Ahmad, N. A.; Sharif, Z. I. M.; Jai, J.; Yusof, N. M.; Mustapha, F. A.

    2018-03-01

    Turmeric oil (TO) has been studied for its potential as an antioxidation agent in starch edible coating for fresh cut apples and its degree of oxidation was analysed. TO incorporate with starch edible coating was examined using FT-IR Spectroscopy to determine the presence of secondary metabolites. The presence of alcohol and aromatic ring in the edible coating film proved that the secondary metabolites from TO were existed. The fresh cut apples were underwent the sensory test and six out of ten panellist concluded that coated fresh cut apples have good appearance and surface colour. Fresh cut apples were coated with edible coating incorporated with different concentrations of TO (uncoated, 0μL, 5μL, 10μL, 15μL. Percentage weight loss for 15μL were the least which were 1.98% (day 6) and 3.95% (day 12). Colour measurement were done for few days and it shows that the total colour difference (ΔΕ) for 15μL were the lowest. Thus, the oxidation activities for 15μL is the slowest compared to the others. These can be proved through the degree of oxidation analysis using UV-Vis spectroscopy. Uncoated fresh cut apples have the highest degree of oxidation while those with 15μL have the lowest. This study can be illustrated that the oxidation activities of fresh cut apples could be postponed using edible film incorporated with TO.

  14. Applications of edible films and coatings to processed foods

    Science.gov (United States)

    Edible coatings have been successfully applied in processed foods such as meat, cereals, confectionaries, dried fruits, nuts and fresh and fresh-cut fruits and vegetables. These coatings are used to improve the quality and shelf-life of foods. Furthermore, different food ingredients, derived from ...

  15. Films and edible coatings containing antioxidants - a review

    Directory of Open Access Journals (Sweden)

    Kaliana Sitonio Eça

    2014-06-01

    Full Text Available The incorporation of natural antioxidants into films and edible coatings can modify their structure, improving their functionality and applicability in foods, such as in fresh-cut fruits. This paper reviews the more recent literature on the incorporation of antioxidants from several sources into films and edible coatings, for application in fruits and vegetables. The use of synthetic antioxidants in foods has been avoided due to their possible toxic effects. Instead, a wide range of natural antioxidants (such as essential oils and plant extracts, as well as pure compounds, like ascorbic acid and α-tocopherol have been incorporated into edible films and coatings to improve their bioactive properties. Films and coatings containing added antioxidants help to preserve or enhance the sensory properties of foods and add value to the food products by increasing their shelf life.

  16. Edible films and coatings: Sources, properties and application

    Directory of Open Access Journals (Sweden)

    Šuput Danijela Z.

    2015-01-01

    Full Text Available In order to extend product shelf life while preserving the quality scientific attention focused to biopolymers research that are base for edible films and coatings production. Another major advantage of this kind of food packaging is their eco-friendly status because biopolymers do not cause environmental problems as packaging materials derived from non-renewable energy sources do. Objective of this work was to review recently studied edible films and coatings - their sources, properties and possible application. As sources for edible biopolymers were highlighted polysaccharides, proteins and lipids. The most characteristic subgroups from each large group of compounds were selected and described regarding possible physical and mechanical protection; migration, permeation, and barrier functions. The most important biopolymers characteristic is possibility to act as active substance carriers and to provide controlled release. In order to achieve active packaging functions emulsifiers, antioxidants and antimicrobial agents can also be incorporated into film-forming solutions in order to protect food products from oxidation and microbial spoilage, resulting in quality improvement and enhanced safety. The specific application where edible films and coatings have potential to replace some traditional polymer packaging are explained. It can be concluded that edible films and coatings must be chosen for food packaging purpose according to specific applications, the types of food products, and the major mechanisms of quality deterioration.

  17. Development of Aloe vera based edible coating for tomato

    Science.gov (United States)

    Athmaselvi, K. A.; Sumitha, P.; Revathy, B.

    2013-12-01

    The effect of formulated Aloe vera based edible coating on mass loss, colour, firmness, pH, acidity, total soluble solid, ascorbic acid and lycopene on the coated tomato was investigated. The tomato in control showed a rapid deterioration with an estimated shelf life period of 19 days, based on the mass loss, colour changes, accelerated softening and ripening. On the contrary, the coating on tomatoes delayed the ripening and extended the shelf life up to 39 days. The physiological loss in weight was 7.6 and 15.1%, firmness was 36 and 46.2 N on 20th day for control and coated tomatoes, respectively. From the results, it was concluded that the use of Aloe vera based edible coating leads to increased tomato shelf-life.

  18. Anthocyanins, phenolics and antioxidant capacity after fresh storage of blueberry treated with edible coatings.

    Science.gov (United States)

    Chiabrando, Valentina; Giacalone, Giovanna

    2015-05-01

    The influence of different edible coatings on total phenolic content, total anthocyanin and antioxidant capacity in highbush blueberry (Vaccinium corymbosum L. cv Berkeley and O'Neal) was investigated, mainly for industrial applications. Also titratable acidity, soluble solids content, firmness and weight loss of berries were determined at harvest and at 15-day intervals during 45 storage days at 0 °C, in order to optimize coating composition. Application of chitosan coating delayed the decrease in anthocyanin content, phenolic content and antioxidant capacity. Coating samples showed no significant reduction in the weight loss during storage period. In cv Berkeley, the use of alginate coating showed a positive effect on firmness, titratable acidity and maintained surface lightness of treated berries. In cv O'Neal, no significant differences in total soluble solids content were found, and the chitosan-coated berries showed the minimum firmness losses. In both cultivars, the addition of chitosan to coatings decreases the microbial growth rate.

  19. Effects of mesquite gum-candelilla wax based edible coatings on the quality of guava fruit (Psidium guajava L.)

    Science.gov (United States)

    Tomás, S. A.; Bosquez-Molina, E.; Stolik, S.; Sánchez, F.

    2005-06-01

    The ability of composite edible coatings to preserve the quality of guava fruit (Psidium guajava L.) at 20ºC was studied for a period of 15 days. The edible coatings were formulated with candelilla wax blended with white mineral oil as the lipid phase and mesquite gum as the structural material. The use of edible coatings prolonged the shelf life of treated fruits by retarding ethylene emission and enhancing texture as compared to control samples. At the sixth day, the ethylene produced by the control samples was fivefold higher than the ethylene produced by the coated samples. In addition, the physiological weight loss of coated fruits was nearly 30% lower than the control samples.

  20. Application of edible coating from cassava peel – bay leaf on avocado

    Science.gov (United States)

    Handayani, M. N.; Karlina, S.; Sugiarti, Y.; Cakrawati, D.

    2018-05-01

    Avocados have a fairly short shelf life and are included in climacteric fruits. Edible coating application is one alternative to maintain the shelf life of avocado. Cassava peel starch is potential to be used as raw material for edible coating making. Addition of bay leaf extract containing antioxidants can increase the functional value of edible coating. The purpose of this study is to know the shrinkage of weight, acid number, color change and respiration rate of avocado coated with edible coating from cassava peel starch with an addition of bay leaf extract. The study consisted of making cassava peel starch, bay leaf extraction, edible coating making, edible coating application on avocado, and analysis of avocado characteristics during storage at room temperature. The results showed that addition of bay leaf extract on cassava peel starch edible coating applied to avocado, an effect on characteristics of avocado. Avocado applied edible coating and stored at room temperatures had lower weight loss than avocado without edible coating, lower acid number, tend to be more able to maintain color rather than avocado without edible coating.

  1. Effect of Protein-Based Edible Coating from Red Snapper (Lutjanus sp.) Surimi on Cooked Shrimp

    Science.gov (United States)

    Rostini, I.; Ibrahim, B.; Trilaksani, W.

    2018-02-01

    Surimi can be used as a raw material for making protein based edible coating to protect cooked shrimp color. The purpose of this study was to determine consumers preference level on cooked shrimp which coated by surimi edible coating from red snapper and to know the microscopic visualization of edible coating layer on cooked shrimp. The treatments for surimi edible coating were without and added by sappan wood (Caesalpinia sappan Linn) extract. Application of surimi edible coating on cooked shrimp was comprised methods (1) boiled then coated and (2) coated then boiled. Edible coating made from surimi with various concentrations which were 2, 6, 10 and 14% of distillated water. The analysis were done using hedonic test and microscopic observation with microscope photographs. Effect of surimi edible coating on cooked shrimp based on the hedonic and colour test results showed that the 14% surimi concentration, added by sappan wood (Caesalpinia sappan Linn) extract on edible coating was the most preferable by panellist and giving the highest shrimp colour. The edible coating surimi application on cooked shrimp which gave the best result was processed by boiling followed by coating.

  2. Proximate and mineral composition of four edible mushroom species

    African Journals Online (AJOL)

    Owner

    Key words: Edible mushrooms; food composition. INTRODUCTION. Mushrooms are saprophytes. ... riboflavin, biotin and thiamine (Chang and Buswell,. 1996). Ogundana and Fagade (1981) indicated that ... Four edible mushroom species were analyzed for food composition according to the Association of Official Analytical ...

  3. Recent innovations in the area of edible films and coatings.

    Science.gov (United States)

    Maftoonazad, Neda; Badii, Fojan; Shahamirian, Maryam

    2013-12-01

    Edible films/coatings have been considered as one of the potential technologies that can be used to increase the storability of foods and to improve the existent packaging technology, helping to ensure the microbial safety and the preservation of food from the influence of external factors. Innovations constantly appear in food packaging, always aiming at creating a more efficient quality preservation system while improving foods' attractiveness and marketability. The utilization of renewable sources for packaging materials, such as hydrocolloids and lipids from biological origin, is one the main trends of the industry. These films should have acceptable sensory characteristics, appropriate barrier properties (CO2, O2, water, oil), microbial, biochemical and physicochemical stability, they should be safe, and produced by simple technology in low cost. Also they can act as effective carrier for antioxidant, flavor, color and nutritional or anti-microbial additives. Nowadays, a great discussion exists about the potential applications of edible films/coatings on food products. The general trend is to find the correct combination between the food product and the edible film/coating, which will ensure the success of the technology.

  4. Edible films and coatings in seafood preservation: A review.

    Science.gov (United States)

    Dehghani, Samira; Hosseini, Seyed Vali; Regenstein, Joe M

    2018-02-01

    Seafood is highly perishable and has a short shelf-life. During storage many reactions occur leading to changes in quality such as endogenous chemical and enzymatic reactions. The safety and shelf-life are related to the presence of food spoilage and pathogenic microorganisms. Despite improved manufacturing facilities and implementation of effective process control procedures such as the Hazard Analysis Critical Control Point system by seafood companies, the number of seafood-related foodborne illnesses has increased. Edible coatings can improve the quality of fresh and frozen products by retarding microbial growth, reducing lipid oxidation and moisture loss, and functioning as a carrier of food additives such as antimicrobial and antioxidant agents. Biodegradable edible coatings have various advantages over synthetic coatings such as being edible and generally being more environmentally friendly. This paper reviews the application of various types of natural bio-polymer and different active ingredients incorporated into the films and their effects on seafood quality attributes. Copyright © 2017 Elsevier Ltd. All rights reserved.

  5. Seaweed Extracts as Edible Coatings for Minimally Processed Products

    Directory of Open Access Journals (Sweden)

    Ana Augusto

    2014-05-01

    The EC containing Codium tomentosum seaweed extract showed the better performance by minimizing physical and chemical changes in RTE apples, namely: minor changes of moisture, total soluble solids and firmness values. In relation to the browning index, after 20 days of storage, RTE apples coated with EC containing Codium tomentosum seaweed extract showed the lowest values, also the results of peroxidase and polyphenoloxidase showed lower activity compared with the EC containing Fucus spirals, Bifurcaria bifurcate and Codium vermilara seaweed extracts, citric acid EC and the control. These results also allowed a pending patent application nº 107369 “Revestimento de origem marinha para aplicação em produtos minimamente processados ou de quarta gama” which is related with an edible coating with the incorporation of bioactive compounds from macroalgae for minimally processed products.

  6. Nanosystems in Edible Coatings: A Novel Strategy for Food Preservation

    Directory of Open Access Journals (Sweden)

    María L. Zambrano-Zaragoza

    2018-03-01

    Full Text Available Currently, nanotechnology represents an important tool and an efficient option for extending the shelf life of foods. Reducing particle size to nanometric scale gives materials distinct and improved properties compared to larger systems. For food applications, this technology allows the incorporation of hydrophilic and lipophilic substances with antimicrobial and antioxidant properties that can be released during storage periods to increase the shelf life of diverse products, including whole and fresh-cut fruits and vegetables, nuts, seeds, and cheese, among others. Edible coatings are usually prepared with natural polymers that are non-toxic, economical, and readily available. Nanosystems, in contrast, may also be prepared with biodegradable synthetic polymers, and liquid and solid lipids at room temperature. In this review, recent developments in the use of such nanosystems as nanoparticles, nanotubes, nanocomposites, and nanoemulsions, are discussed critically. The use of polymers as the support matrix for nanodispersions to form edible coatings for food preservation is also analyzed, but the central purpose of the article is to describe available information on nanosystems and their use in different food substrates to help formulators in their work.

  7. Nanosystems in Edible Coatings: A Novel Strategy for Food Preservation

    Science.gov (United States)

    Zambrano-Zaragoza, María L.; González-Reza, Ricardo; Miranda-Linares, Verónica; Bernal-Couoh, Tania F.; Mendoza-Elvira, Susana; Quintanar-Guerrero, David

    2018-01-01

    Currently, nanotechnology represents an important tool and an efficient option for extending the shelf life of foods. Reducing particle size to nanometric scale gives materials distinct and improved properties compared to larger systems. For food applications, this technology allows the incorporation of hydrophilic and lipophilic substances with antimicrobial and antioxidant properties that can be released during storage periods to increase the shelf life of diverse products, including whole and fresh-cut fruits and vegetables, nuts, seeds, and cheese, among others. Edible coatings are usually prepared with natural polymers that are non-toxic, economical, and readily available. Nanosystems, in contrast, may also be prepared with biodegradable synthetic polymers, and liquid and solid lipids at room temperature. In this review, recent developments in the use of such nanosystems as nanoparticles, nanotubes, nanocomposites, and nanoemulsions, are discussed critically. The use of polymers as the support matrix for nanodispersions to form edible coatings for food preservation is also analyzed, but the central purpose of the article is to describe available information on nanosystems and their use in different food substrates to help formulators in their work. PMID:29494548

  8. Extraction of pectin from passion fruit rind (Passiflora edulis var. flavicarpa Degener) for edible coating

    Science.gov (United States)

    Inayati, Puspita, Rifka Intan; Fajrin, Vika Latifiana

    2018-02-01

    One of fruit preservation method is by applying the edible coating. Rind of passion fruit (Passiflora edulis var. flavicarpa Degener), which is kind of waste, can be utilized as edible coating through pectin extraction process. The purposes of this work were to determine the suitable solvent for the pectin extraction and techniques for applying the produced edible coating on strawberry, to produce edible coating from the pectin, and the test the performance of the edible coating which was applied to strawberries. Pectin from passion fruit rind was collected through conventional extraction method using two types of solvent, i.e. acetic acid solution and hydrochloric acid solution with concentration of 0.01 N, 0.015 N, 0.02 N, 0.025 N, and 0.03 N. The results showed that chloric acid solution was more suitable for the pectin extraction from passion fruit. Maximum yield of 30.78% was obtained at hydrochloric acid concentration of 0.02 N. Obtained pectin from the extraction was then processed into the edible coating by adding plasticizers and calcium chloride dihydrate. Storability of the coated strawberry was observed to measure the performance of the edible coating

  9. Radiation curable coating compositions

    International Nuclear Information System (INIS)

    Jenkinson, R.D.; Carder, C.H.

    1979-01-01

    The present invention provides a low-toxicity diluent component for radiation curable coating compositions that contain an acrylyl or methacryly oligomer or resin component such as an acrylyl urethane oligomer. The low-toxicity diluent component of this invention is chosen from the group consisting of tetraethlorthosilicate and tetraethoxyethylorthosilicate. When the diluent component is used as described, benefits in addition to viscosity reduction, may be realized. Application characteristics of the uncured coatings composition, such as flowability, leveling, and smoothness are notably improved. Upon curing by exposure to actinic radiation, the coating composition forms a solid, non-tacky surface free of pits, fissures or other irregularities. While there is no readily apparent reactive mechanism by which the orthosilicate becomes chemically bonded to the cured coating, the presence of silicon in the cured coating has been confirmed by scanning electron microscopy. 12 drawing

  10. KAJIAN TEKNOLOFI EDIBLE COATING DARI PATI DAN APLIKASINYA UNTUK PENGEMAS PRIMER LEMPOK DURIAN [Technological Assessment of Starch Edible Coating and Its Application on Primary Packaging of Durian Sweets

    Directory of Open Access Journals (Sweden)

    Budi Santoso1

    2004-12-01

    Full Text Available The study objective was to determine the shelf life of edible coating packaged of durian lempok. The experimental method used in this study was Factorial Randomized Block Design consisting of three factors. These factors were tapioca starch, stearate acid, and CMC. The edible coating solution was applied in to durian lempok by using dip method. The result showed that edible coating packaged of durian lempok could increase the durian lempok shelf life by 67 percent than durian lempok without edible coating. The edible coating was capable of decreasing the durian lempok weight loss by magnitude of 36.38% during storage, decreasing the peroxide number by magnitude of 33.33%, decreasing the water content by magnitude of 7.54%, and suppressing the microbial growth by the amount of 31.20%, respectively. Visual change of non-coating lempok had occurred on the day of 19th, which was indicated by greyish-white colour change due to certain type of mold on lempok surface, while the similar change happened at day of 31th (T2A3C3 treatment.

  11. Optimisation of gellan gum edible coating for ready-to-eat mango (Mangifera indica L.) bars.

    Science.gov (United States)

    Danalache, Florina; Carvalho, Claudia Y; Alves, Vitor D; Moldão-Martins, Margarida; Mata, Paulina

    2016-03-01

    The optimisation of an edible coating based on low acyl (L)/high acyl (H) gellan gum for ready-to-eat mango bars was performed through a central composite rotatable design (CCRD). The independent variables were the concentration of gellan (L/H90/10) and the concentration of Ca(2+) in the coating solution, as well as the storage time after coating application. The response variables studied were the coating thickness, mango bars firmness, syneresis, and colour alterations. Gellan concentration was the independent variable that most influenced the thickness of the coating. Syneresis was quite low for the conditions tested (mango bars. The release of eight volatile compounds from the uncoated and coated mango bars with the selected formulation was analysed by Headspace - Solid Phase Micro Extraction-Gas Chromatography during 9 days of refrigerated storage. This work showed that the coating can improve mango bars sensory characteristics (appearance and firmness) and stability in terms of syneresis, colour and volatiles content during storage increasing the commercial value of the final product. Crown Copyright © 2015. Published by Elsevier B.V. All rights reserved.

  12. Evaluation of using edible coating and ripening on Dangke, a traditional cheese of Indonesia

    Directory of Open Access Journals (Sweden)

    Malaka, R.

    2017-03-01

    Full Text Available Dangke is a traditional soft cheese from Enrekang, South Sulawesi Indonesia which is produced through heat denaturation at 85°C and enzymatic coagulation using papaya latex. The quality, microstructure and storage life of the cheese are affected by several factors such as denaturation temperature, enzyme concentration, moulding pressure, coating, and ripening. The objective of this study was to evaluated of using edible coating and ripening on Dangke cheese. The experiment was conducting using factorial design with five replications. The experimental variables were the type of edible coating used (agar, CMC and bee wax and the length of ripening (10, 20 and 30 days. Parameter was measured hardness, microstructure, and sensory evaluation. The overall result indicated that the use of edible coating can extend the shelf life, increase hardness, and more compact microstructure. Sensory evaluation also indicated that the cheese coated with film forming edible materials had had white color, more milk like smell (smelly milk, and smoother texture.

  13. Conservation of Williams pear using edible coating with alginate and carrageenan

    Directory of Open Access Journals (Sweden)

    Kessiane Silva de Moraes

    2012-12-01

    Full Text Available The aim of this study was to evaluate the physical and chemical parameters of Williams pear, stored at 25 ºC for 15 days, with and without edible coating. Edible coatings prepared with alginate 2% and carrageenan 0.5% were tested. The analyses carried out on the samples were: weight loss, pH, soluble solids, firmness, and color. The edible coatings were characterized in terms of mechanical properties, permeability, thickness, and opacity. The results show that the application of edible coatings with carrageenan and alginate in pears influenced physical and chemical characteristics such as weight loss, pH, total soluble solids, color, and firmness of the fruit. However, the alginate coating showed the best results on pear conservation since it had lower water vapor permeability and greater tensile strength, and therefore it can be used as a protective film on these fruits.

  14. IMPROVEMENT OF SHELF LIFE QUALITY OF GREEN BELL PEPPERS USING EDIBLE COATING FORMULATIONS

    Directory of Open Access Journals (Sweden)

    Emilio Ochoa-Reyes

    2013-06-01

    Full Text Available In Latin-America, there are countries with high production levels of green bell peppers, which requires of new strategies of conservation for their international trade. Traditional techniques of preservations do not guarantee to prolong the shelf life of these kinds of fruits, for this reason, in the present study, the Influence of different edible coating formulations on shelf-life quality of green bell peppers was studied. Three different biopolymers (pectin, arabic, and xanthan gums were evaluated in mixtures with candelilla wax as hydrophobic phase, jojoba oil as plasticizer and a crude extract of polyphenols as source of bioactive compounds. Green bell peppers were immersion-treated and then stored at room temperature. Response variables were: weight loss, color, appearance, pH, total soluble solids and firmness changes which were kinetically determined. All peppers treated with edible-coating showed a significant difference (Tukey, p≤0.05 in weight loss compared to control treatment (without edible coating, while a lower level of deterioration was observed in fruits treated with edible coating formulated with arabic gum, but appearance remained similar among fruits treated with different edible coatings. Use of mixtures of biopolymers, candelilla wax, jojoba oil and polyphenols to develop edible and functionalized coatings significantly extended shelf life of green bell pepper.

  15. Edible coating as carrier of antimicrobial agents to extend the shelf life of fresh-cut apples

    Science.gov (United States)

    Edible coatings with antimicrobial agents can extend shelf-life of fresh-cut fruits. The effect of lemongrass, oregano oil and vanillin incorporated in apple puree-alginate edible coatings, on shelf-life of fresh-cut 'Fuji' apples, was investigated. Coated apples were packed in air filled polypropyl...

  16. A photoacoustic technique applied to detection of ethylene emissions in edible coated passion fruit

    International Nuclear Information System (INIS)

    Alves, G V L; Santos, W C dos; Vargas, H; Silva, M G da; Waldman, W R; Oliveira, J G

    2010-01-01

    Photoacoustic spectroscopy was applied to study the physiological behavior of passion fruit when coated with edible films. The results have shown a reduction of the ethylene emission rate. Weight loss monitoring has not shown any significant differences between the coated and uncoated passion fruit. On the other hand, slower color changes of coated samples suggest a slowdown of the ripening process in coated passion fruit.

  17. Effect of Edible Coatings from Aloe vera gel on Citrus sinensis ...

    African Journals Online (AJOL)

    Extension of the shelf life of orange fruits continues to be a challenge in Nigeria. The search for safe, healthy and environmental friendly treatments has led to increased interest in research into edible and biodegradable films and coatings. In this work, the use of Aloe vera gel as a coating to extend the shelf-life of orange ...

  18. Effectiveness of incorporating citric acid in cassava starch edible coatings to preserve quality of Martha tomatoes

    Science.gov (United States)

    Ambarsari, I.; Oktaningrum, G. N.; Endrasari, R.

    2018-01-01

    Tomato as an agricultural product is extremely perishable. Coatings of tomatoes with edible starch extend quality and storage life of the fruits. Incorporation of citric acid as antimicrobial agent in the edible starch coatings is expected to preserve the quality of tomatoes during storage. The aim of this study was to verify the effectiveness of citric acid incorporated in cassava starch coating to preserve quality of tomatoes. The edible coatings formula consisted of cassava starch solutions (1; 2; 3%), citric acid (0.5; 1.0%) and glycerol (10%). Tomatoes were dipped to the coating solution for 10 seconds, then air-dried and stored at room temperature during 18 days. All the treatments were carried out in triplicates. Experimental data were analyzed using One Way ANOVA. The results showed that coating treatments did not affect the weight loss, moisture content, color characteristic, carotene and vitamin C content on Martha tomatoes. The low concentration of starch coating on Martha tomatoes are indicated to be the reason why there was no significant difference between coated and coated tomatoes for some parameters. However, incorporating citric acid in cassava starch-based coatings could prevent tomato fruits from firmness reduction and spoilage during storage.

  19. PENGARUH MINYAK ATSIRI JAHE MERAH DAN LENGKUAS MERAH PADA EDIBLE COATING TERHADAP KUALITAS FILLET IKAN PATIN (Effect of Edible Coating Enriched with Red Ginger and Red Galangal Essential Oil on the Quality of Patin Fillet

    Directory of Open Access Journals (Sweden)

    Rohula Utami

    2014-02-01

    edible coating will retain the patin fillets quality. In terms of microbial quality and TVB value, 1% essential oil of red ginger and red galangal enrichment in edible coating could extend shelf life of patin fillets for 2-4 days. Keywords: Edible coating, essential oil, patin, red ginger, red galangal   ABSTRAK Penentuan pengaruh penambahan minyak atsiri jahe merah dan lengkuas merah dalam edible coating terhadap kualitas fillet ikan patin selama penyimpanan dingin dilakukan pada periode waktu 8 hari. Parameter kualitas ikan yang dianalisis adalah kualitas mikrobiologis (Total Plate Count/TPc, dan kualitas fisikokimia (Total Volatile Bases/TVB, Thiobarbituricacid/TBa, pH, dan warna. Variasi perlakuan fillet ikan patin yaitu konsentrasi minyak atsiri (0 %; 0,1%; 1% yang ditambahkan dalam edible coating. Hasil penelitian ini mengindikasikan bahwa penambahan minyak atsiri baik jahe merah maupun lengkuas merah berpengaruh terhadap kualitas fillet ikan patin selama penyimpanan dingin. Penambahan minyak atsiri dalam edible coating mampu mempertahankan kualitas fillet ikan patin lebih baik dibandingkan perlakuan edible coating tanpa minyak atsiri. Berdasarkan kualitas mikrobiologis dan nilai TVB, perlakuan minyak atsiri jahe merah 1% dan minyak atsiri lengkuas merah 1% mampu meningkatkan umur simpan fillet ikan patin selama 2-4 hari. Kata kunci: Edible coating, jahe merah, lengkuas merah, minyak atsiri, patin

  20. Chemical composition and mineral elements of edible insects (at ...

    African Journals Online (AJOL)

    The Chemical Composition and Mineral Elements of two edible insects' larvae and termite soldiers were assayed. Their ash content were between 1.01% and 7.50%. The legless larva (LS) had 28.52% fat, while the solider ant had 7.14% and the Legged larva (LG) had 1.50%. The white ant (SA) had 15.61% protein while ...

  1. Polysaccharide-Based Edible Coatings Containing Cellulase for Improved Preservation of Meat Quality during Storage.

    Science.gov (United States)

    Zimoch-Korzycka, Anna; Jarmoluk, Andrzej

    2017-03-02

    The objectives of this study were to optimize the composition of edible food coatings and to extend the shelf-life of pork meat. Initially, nine meat samples were coated with solutions containing chitosan and hydroxypropyl methylcellulose at various cellulase concentrations: 0%, 0.05%, and 0.1%, stored for 0, 7, and 14 days. Uncoated meat served as the controls. The samples were tested for pH, water activity (a w ), total number of microorganisms (TNM), psychrotrophs (P), number of yeast and molds (NYM), colour, and thiobarbituric acid-reactive substances (TBARS). The pH and a w values varied from 5.42 to 5.54 and 0.919 to 0.926, respectively. The reductions in the TNM, P, and NYM after 14 days of storage were approximately 2.71 log cycles, 1.46 log cycles, and 0.78 log cycles, respectively. The enzyme addition improved the stability of the red colour. Significant reduction in TBARS was noted with the inclusion of cellulase in the coating material. Overall, this study provides a promising alternative method for the preservation of pork meat in industry.

  2. Polysaccharide-Based Edible Coatings Containing Cellulase for Improved Preservation of Meat Quality during Storage

    Directory of Open Access Journals (Sweden)

    Anna Zimoch-Korzycka

    2017-03-01

    Full Text Available The objectives of this study were to optimize the composition of edible food coatings and to extend the shelf-life of pork meat. Initially, nine meat samples were coated with solutions containing chitosan and hydroxypropyl methylcellulose at various cellulase concentrations: 0%, 0.05%, and 0.1%, stored for 0, 7, and 14 days. Uncoated meat served as the controls. The samples were tested for pH, water activity (aw, total number of microorganisms (TNM, psychrotrophs (P, number of yeast and molds (NYM, colour, and thiobarbituric acid-reactive substances (TBARS. The pH and aw values varied from 5.42 to 5.54 and 0.919 to 0.926, respectively. The reductions in the TNM, P, and NYM after 14 days of storage were approximately 2.71 log cycles, 1.46 log cycles, and 0.78 log cycles, respectively. The enzyme addition improved the stability of the red colour. Significant reduction in TBARS was noted with the inclusion of cellulase in the coating material. Overall, this study provides a promising alternative method for the preservation of pork meat in industry.

  3. Effect of Edible and Active Coating (with Rosemary and Oregano Essential Oils) on Beef Characteristics and Consumer Acceptability

    Science.gov (United States)

    Vital, Ana Carolina Pelaes; Guerrero, Ana; Monteschio, Jessica de Oliveira; Valero, Maribel Velandia; Carvalho, Camila Barbosa; de Abreu Filho, Benício Alves; Madrona, Grasiele Scaramal; do Prado, Ivanor Nunes

    2016-01-01

    The effects of an alginate-based edible coating containing natural antioxidants (rosemary and oregano essential oils) on lipid oxidation, color preservation, water losses, texture and pH of beef steaks during 14 days of display were studied. The essential oil, edible coating and beef antioxidant activities, and beef consumer acceptability were also investigated. The edible coatings decreased lipid oxidation of the meat compared to the control. The coating with oregano was most effective (46.81% decrease in lipid oxidation) and also showed the highest antioxidant activity. The coatings significantly decreased color losses, water losses and shear force compared to the control. The coatings had a significant effect on consumer perception of odor, flavor and overall acceptance of the beef. In particular, the oregano coating showed significantly high values (approximately 7 in a 9-point scale). Active edible coatings containing natural antioxidants could improve meat product stability and therefore have potential use in the food industry. PMID:27504957

  4. Effect of Edible and Active Coating (with Rosemary and Oregano Essential Oils on Beef Characteristics and Consumer Acceptability.

    Directory of Open Access Journals (Sweden)

    Ana Carolina Pelaes Vital

    Full Text Available The effects of an alginate-based edible coating containing natural antioxidants (rosemary and oregano essential oils on lipid oxidation, color preservation, water losses, texture and pH of beef steaks during 14 days of display were studied. The essential oil, edible coating and beef antioxidant activities, and beef consumer acceptability were also investigated. The edible coatings decreased lipid oxidation of the meat compared to the control. The coating with oregano was most effective (46.81% decrease in lipid oxidation and also showed the highest antioxidant activity. The coatings significantly decreased color losses, water losses and shear force compared to the control. The coatings had a significant effect on consumer perception of odor, flavor and overall acceptance of the beef. In particular, the oregano coating showed significantly high values (approximately 7 in a 9-point scale. Active edible coatings containing natural antioxidants could improve meat product stability and therefore have potential use in the food industry.

  5. Effect of Edible and Active Coating (with Rosemary and Oregano Essential Oils) on Beef Characteristics and Consumer Acceptability.

    Science.gov (United States)

    Vital, Ana Carolina Pelaes; Guerrero, Ana; Monteschio, Jessica de Oliveira; Valero, Maribel Velandia; Carvalho, Camila Barbosa; de Abreu Filho, Benício Alves; Madrona, Grasiele Scaramal; do Prado, Ivanor Nunes

    2016-01-01

    The effects of an alginate-based edible coating containing natural antioxidants (rosemary and oregano essential oils) on lipid oxidation, color preservation, water losses, texture and pH of beef steaks during 14 days of display were studied. The essential oil, edible coating and beef antioxidant activities, and beef consumer acceptability were also investigated. The edible coatings decreased lipid oxidation of the meat compared to the control. The coating with oregano was most effective (46.81% decrease in lipid oxidation) and also showed the highest antioxidant activity. The coatings significantly decreased color losses, water losses and shear force compared to the control. The coatings had a significant effect on consumer perception of odor, flavor and overall acceptance of the beef. In particular, the oregano coating showed significantly high values (approximately 7 in a 9-point scale). Active edible coatings containing natural antioxidants could improve meat product stability and therefore have potential use in the food industry.

  6. Composition superconductive plumbous coatings

    International Nuclear Information System (INIS)

    Volodin, V.N.; Tuleushev, A.Zh.; Tuleushev, Yu.Zh.; Lisizin, V.N.

    2002-01-01

    Independent dispersion of two or more targets, precipitation of pulverized material on substrate and possibility of composition change in wide range of component concentrations made possible ion-plasma forming of film composition materials from materials with different chemical and physical qualities, particularly in lead-aluminum, lead-beryllium and lead-graphite systems. Named systems are characterized in wide sphere of immiscibility in solid and liquid state and absence of intermediate compounds. It is impossible to receive materials from them in traditional method in conditions of gravitational field. In lead-aluminum system there was received a number of film coatings with aluminum content up to 95 at. % at coating thickness up to 2 μm. Owing to X-ray investigations it is fixed that lead and aluminum have been performed by separate phases. Lead in sprayed layer represents well-crystallized phase with grain size more than 100 nm; texturing is not found. Study of physical qualities has shown that materials with lead base 21.6 at. % Al) have enough high crystalline current in comparison with compact lead, which reaches (2.5-3.0)·10 5 A)·cm 2 , while materials with aluminum base (21.6 at. % Al) loose this effect and critical temperature of transition is reduced from 7.1 to 5.8 K. It was impossible to carry out X-rayed analysis for lead-beryllium film because of weak intensity of beryllium lines against a background of lead owing to a quite large difference of atomic balance. Cryogen tests have shown the increase of critical current strength up to (3.1-3.6)·10 4 A)·cm 2 or composition coating of lead-beryllium (56.99 at. % or 5,45 mas. % Be), at that the critical temperature of transition does not differ from lead temperature. Samples of lead edge of state diagram have been received in the lead-graphite system. X-ray investigation subjected coating contained 6.81 at. % (55.82 mas. %) of lead. Choice of the composition is conditioned on possibilities of

  7. Natural gums of plant origin as edible coatings for food industry applications.

    Science.gov (United States)

    Saha, Anuradha; Tyagi, Shvetambri; Gupta, Rajinder K; Tyagi, Yogesh K

    2017-12-01

    Natural plant-based gums and their derivatives are widely utilized in food industries, however, their applications as edible coatings to extend fresh fruits and vegetable shelf-life has been explored recently. These natural polymeric polysaccharides have many advantages as compared to synthetic polymers, because they are biodegradable, nontoxic, economical and easily available in the environment. Natural gums can also be semi synthetically modified to produce derivatives, which can easily compete with the synthetic preservatives available on the food market. In this review, the recent developments in the use of natural gums and their derivatives as edible coatings have been explored and discussed.

  8. Biodegradable packaging and edible coating for fresh-cut fruits and vegetables

    Directory of Open Access Journals (Sweden)

    Fernanda Galgano

    2015-03-01

    Full Text Available This work focuses on biodegradable packaging and edible coatings applied to fresh-cut fruits and vegetables and their effects on the product quality. Practical applications are mainly limited to the use of biodegradable materials that, however, do not allow full control of the product moisture loss. Better results can be achieved by the combined use of biodegradable packagings with edible coatings and recent research has shown that enrichment with silver montmorillonite nanoparticles may be a promising technique. However, the actual utilization of these materials is still limited, due to the high costs of the raw materials and the limited production.

  9. Nutritional composition and safety aspects of edible insects.

    Science.gov (United States)

    Rumpold, Birgit A; Schlüter, Oliver K

    2013-05-01

    Insects, a traditional food in many parts of the world, are highly nutritious and especially rich in proteins and thus represent a potential food and protein source. A compilation of 236 nutrient compositions in addition to amino acid spectra and fatty acid compositions as well as mineral and vitamin contents of various edible insects as derived from literature is given and the risks and benefits of entomophagy are discussed. Although the data were subject to a large variation, it could be concluded that many edible insects provide satisfactorily with energy and protein, meet amino acid requirements for humans, are high in MUFA and/or PUFA, and rich in several micronutrients such as copper, iron, magnesium, manganese, phosphorous, selenium, and zinc as well as riboflavin, pantothenic acid, biotin, and in some cases folic acid. Liabilities of entomophagy include the possible content of allergenic and toxic substances as well as antinutrients and the presence of pathogens. More data are required for a thorough assessment of the nutritional potential of edible insects and proper processing and decontamination methods have to be developed to ensure food safety. © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. Coating material composition

    International Nuclear Information System (INIS)

    Kimura, Tadashi; Ozeki, Takao; Kobayashi, Juichi; Nakamoto, Hideo; Maeda, Yutaka.

    1969-01-01

    A coating material composition is provided which can easily be cross-linked by irradiation with active energy, particularly electron beams and ultraviolet light, using a mixture of a prepolymer (a) with an addition reaction product (b). Such compositions have coating properties as good as thermosetting acrylic or amino alkyd resins. The prepolymer (a) is produced by primarily reacting at least 0.1 mol of saturated cyclocarboxylic acid anhydrides and/or alpha-, beta-ethylene unsaturated carboxylic acid anhydrides by addition reaction with one mol of hydroxyl radicals of a basic polymer having a molecular weight of 1,000 to 100,000, the basic polymer being obtained from 1%-40% of a hydroxyl radical containing vinyl monomer and at least 30% of (meth)acrylate monomer. One mol of the sum of hydroxyl radicals and carboxyl radicals of the primary reaction product undergoes a secondary addition reaction with at least 0.1 mol of an epoxy radical-containing vinyl monomer to form the prepolymer(a). The addition reaction product(b) is produced by reacting an epoxy radical-containing vinyl monomer with alpha-, beta-ethylene unsaturated carboxylic acids or their anhydrides. The coating material composition contains a majority of a mixture consisting of 10%-90% of (a) and 90%-10% of (b) above by weight. Four examples of the production of basic polymers, seven examples of the production of prepolymers, seven examples of the production of oligomers, and five examples of applications are given. (Iwakiri, K.)

  11. Optimization of edible coating formulations for improving postharvest quality and shelf life of pear fruit using response surface methodology.

    Science.gov (United States)

    Nandane, A S; Dave, Rudri K; Rao, T V Ramana

    2017-01-01

    The effect of composite edible films containing soy protein isolate (SPI) in combination with additives like hydroxypropyl methylcellulose (HPMC) and olive oil on 'Babughosha' pear ( Pyrus communis L.) stored at ambient temperature (28 ± 5 °C and 60 ± 10% RH) was evaluated using Response surface methodology (RSM). A total of 30 edible coating formulations comprising of SPI (2-6%, w/v), olive oil (0.7-1.1%, v/v), HPMC (0.1-0.5%, w/v) and potassium sorbate (0-0.4% w/v) were evaluated for optimizing the most suitable combination. Quality parameters like weight loss%, TSS, pH and titrable acidity of the stored pears were selected as response variables for optimization. The optimization procedure was carried out using RSM. It was observed that the response variables were mainly effected by concentration of SPI and olive oil in the formulation. Edible coating comprising of SPI 5%, HPMC 0.40%, olive oil 1% and potassium sorbate 0.22% was found to be most suitable combination for pear fruit with predicted values of response variables indicated as weight loss% 3.50, pH 3.41, TSS 11.13 and TA% 0.513.

  12. Towards Drylands Biorefineries: Valorisation of Forage Opuntia for the Production of Edible Coatings

    Directory of Open Access Journals (Sweden)

    Alba Iris Nájera-García

    2018-06-01

    Full Text Available Species of the genus Opuntia may be a well-suited feedstock for biorefineries located in drylands, where biomass is scarcer than in humid or temperate regions. This plant has numerous uses in Mexico and Central America, and its mucilage is a specialty material with many promising applications. We extracted the mucilage from a forage species, O. heliabravoana Scheinvar, and mixed it with a thermoplastic starch to produce an edible coating. The coating was applied to blackberries, which were then evaluated in terms of several physicochemical and microbiological variables. During a 10-day evaluation period, the physicochemical variables measured in the coated fruits were not significantly different from those of the control group. However, the microbiological load of the coated fruits was significantly lower than that of the uncoated fruits, which was attributed to a decreased water activity under the edible coating. Multivariate analysis of the physicochemical and microbial variables indicated that the storage time negatively affected the weight and size of the coated and uncoated blackberries. Although some sensory attributes have yet to be optimised, our results support the use of the mucilage of forage Opuntia for the formation of edible coatings, as well as their valorisation through a biorefinery approach.

  13. Nutritional composition and solubility of edible bird nest (Aerodramus fuchiphagus)

    Science.gov (United States)

    Halimi, Nurfatin Mohd; Kasim, Zalifah Mohd; Babji, Abdul Salam

    2014-09-01

    Edible bird nest (EBN) produced by certain swiftlet species mainly, Aerodromus fuciphagus. The objectives of this study were to determine and compare the proximate and amino acid composition of EBN obtained from two regions in Peninsular Malaysia (Pahang-A & Terengganu-B). The solubility of edible bird nest with varying pH, temperature and time was also investigated in this study. The results showed that, the EBN contained crude protein accounted to 58.55% (A) and 55.48% (B), carbohydrate at22.28% (A) & 25.79% (B), moisture content 15.90% (A) & 15.87% (B), fat, 0.67% (A) & and 0.29% (B) and ash contents 2.60% (A) & 2.57% (B) respectively. The major amino acids found in edible bird nest EBN were Glutamic acid (9.61%), Aspartic acid (6.34%), Lysine (5.44 %) and also Leucine (5.30%). The total solubility of EBN was also found to be increased when the temperature was increased increase with distilled water yielding the highest total solubility of EBN compared to others buffer (different pH) solutions.

  14. Effect of concentration of Curcuma longa L. on chitosan-starch based edible coating

    Science.gov (United States)

    Yusof, N. M.; Jai, J.; Hamzah, F.; Yahya, A.; Pinijsuwan, S.

    2017-08-01

    The ability of chitosan-starch based coating to extend shelf life of strawberry were studied. The main objectives of this paper is to study the effects of different concentrations (20, 15, 10 and 5 µL) of Curcuma longa L. (CUR) essential oil into chitosan-based edible coating on surface tension in order to increase the effectiveness of the coating. CUR or turmeric is one of the commercially planted herbs in Malaysia for its phytochemical benefits. Application of edible coating using dipping technique has been analysed and evaluated for their effectiveness in extending shelf life of fruits. Surface tension was analysed to investigate the adhesion properties. The best CUR concentration was 15 µL with the optimum surface tension was found to be 31.92 dynes/cm.

  15. Effect of edible coatings on bioactive compounds and antioxidant capacity of tomatoes at different maturity stages.

    Science.gov (United States)

    Dávila-Aviña, Jorge E; Villa-Rodríguez, José A; Villegas-Ochoa, Mónica A; Tortoledo-Ortiz, Orlando; Olivas, Guadalupe I; Ayala-Zavala, J Fernando; González-Aguilar, Gustavo A

    2014-10-01

    This work evaluated the effect of carnauba and mineral oil coatings on the bioactive compounds and antioxidant capacity of tomato fruits (cv. "Grandela"). Carnauba and mineral oil coatings were applied on fresh tomatoes at two maturity stages (breaker and pink) over 28 day of storage at 10 °C was evaluated. Bioactive compound and antioxidant activity assays included total phenols, total flavonoids, ascorbic acid (ASA), lycopene, DPPH radical scavenging activity (%RSA), trolox equivalent antioxidant capacity (TEAC) and oxygen radical absorbance capacity assay (ORAC). The total phenolic, flavonoid and lycopene contents were significantly lower for coated fruit than control fruits. However, ascorbic acid content was highest in fruits treated with carnauba, followed by mineral oil coating and control fruits. The ORAC values were highest in breaker tomatoes coated with carnauba wax, followed by mineral oil-coated fruits and controls. No significant differences in ORAC values were observed in pink tomatoes. % RSA and TEAC values were higher for controls than for coated fruit. Edible coatings preserve the overall quality of tomatoes during storage without affecting the nutritional quality of fruit. We found that the physiological response to the coatings is in function of the maturity stage of tomatoes. The information obtained in this study support to use of edible coating as a safe and good alternative to preserve tomato quality, and that the changes of bioactive compounds and antioxidant activity of tomato fruits, was not negatively affected. This approach can be used by producers to preserve tomato quality.

  16. Pepper Extract 'Biquinho' as an edible coating on conservation of guavas

    Directory of Open Access Journals (Sweden)

    Emanuelly Rodrigues Dantas

    2017-10-01

    Full Text Available Belonging to the species Capsicum chinense, ‘Pout’ Pepper differs from the other due to its salient characteristics of shape, color and absence of pungency, but its use is currently limited, basically in the ornamentation of dishes in cooking, being left aside the numerous other benefits chemicals existing in it. It was aimed the elaboration of edible lining with different concentrations of 'Pout’ pepper extract, besides applying it in the conservation of guavas marketed in the backwoods of Paraiba. For this, the extracts were obtained following to the method of extracting alcohol, incorporated in the coating prepared edible, applied by immersion in the steal and conducted the analyzes. The microbiological results, fruits in which there was the application of the coating, in other words, with extract present, showed a great efficiency in their conservation, especially under the action of yeasts and molds in the fungicidal action was not observed in the guavas were applied to the coating with a greater quantity of extract. Concerning to physical-chemical, all the guavas have achieved good results, especially in the quantification of vitamin C, that the application of the coating caused a lower degradation of vitamin according to the period of analysis. It remains clear then, the effective proof of the action of the edible coating elaborated, thus understanding the proposed objective.The effective proof of the antifungal action of the elaborated coating was achieved, as expected in previous studies, and could be applied in guavas and delayed in the senescence process.

  17. Improvement of Shelf Life and Sensory Quality of Pears Using a Specialized Edible Coating

    Directory of Open Access Journals (Sweden)

    Virgilio Cruz

    2015-01-01

    Full Text Available An edible coating functionalized with pomegranate polyphenols was designed. Different blends of candelilla wax, gum arabic, jojoba oil, and pomegranate polyphenols were formulated in order to improve the shelf life quality of pears (variety Bartlett, and all formulations were applied by immersion onto the fruit surface. Coated pears with and without polyphenols and uncoated pears (control were stored under the same conditions. Fruits were analyzed to evaluate changes in their physicochemical, microbiological, and sensorial properties during 30 days of storage at room temperature. Coated pears coded as T13 (candelilla wax 3%, gum arabic 4%, jojoba oil 0.15%, and pomegranate polyphenols 0.015% extended and improved their shelf life quality due to the minimization of the physic-chemical changes and sensorial properties. Therefore, the results indicated that the formulated edible coating has potential to extend the shelf life and maintain quality of pears. It was probed that coated pears were accepted for consumers as a good product. Edible coating application represents a good alternative to keep pears freshness for longer periods.

  18. Electroless alloy/composite coatings

    Indian Academy of Sciences (India)

    The market for these coatings is expanding fast as the potential applications are on the rise. In the present article, an attempt has been made to review different electroless alloy/composite coatings with respect to bath types and their composition, properties and applications. Different characterisation studies have been ...

  19. [Fatty acid composition of edible marine fish in Zhoushan, Zhejiang province].

    Science.gov (United States)

    Gao, Yi-xiong; Yue, Bing; Yu, Xin-wei; He, Jia-lu; Shang, Xiao-hong; Li, Xiao-wei; Wu, Yong-ning

    2013-06-01

    To analyze the main fatty acids in edible marine fish from Zhoushan, Zhejiang province. From September to October 2011, a total of 186 edible marine fish (31 species,6 individual fishes/species) were collected in local markets. Total lipids of edible part were extracted by Folch's method and fatty acids were separated and quantified by gas chromatographic after the homogenization of edible part. The differences of composition of n-6 polyunsaturated fatty acid (n-6 PUFA), n-3 polyunsaturated fatty acid (n-3 PUFA),saturated fatty acid (SFA) and monounsaturated fatty acid (MUFA) among fishes were analyzed. Among the 31 fishes, total lipids were highest in Auxis thazard ((13.2 ± 1.2)g/100 g edible part) and lowest in Thamnaconus modestus ((0.6 ± 0.1)g/100 g edible part). Total n-6 PUFA were highest in Mugil cephalus ((875.7 ± 506.4)mg/100 g edible part) and lowest in Seriola quinqueradiata((2.1 ± 1.9)mg/100 g edible part). Total n-3 PUFA were highest in Auxis thazard ((2623.8 ± 426.1)mg/100 g edible part) and lowest in Scoliodon sorrakowah ((82.0 ± 13.9)mg/100 g edible part). SFA were highest in Trachinotus ovatus((3014.9 ± 379.0)mg/100 g edible part) and lowest in Seriola quinqueradiata ((89.7 ± 5.8)mg/100 g edible part). MUFA were highest in Coilia nasus ((3335.7 ± 383.5)mg/100 g edible part) and lowest in Thamnaconus modestus ((32.1 ± 16.9)mg/100 g edible part). There were significant differences of composition of total lipids and of fatty acids among 31 edible marine fish species from Zhoushan.

  20. Use of edible films and coatings to extend the shelf life of food products.

    Science.gov (United States)

    Maftoonazad, Neda; Badii, Fojan

    2009-06-01

    The increased consumer demand for high quality, extended shelf life, ready to eat foods has initiated the development of several innovative techniques to keep their natural and fresh appearance as long as possible and at the same time render them safe. Packaging has been an important element in these preservation concepts for providing the appropriate (mechanical and functional) protection to the commodity. Since synthetic packaging materials contribute to the environmental pollution, edible coatings and packages have been proposed to replace or complement conventional packaging. Biodegradable and edible films and coatings are made from naturally occurring polymers and functional ingredients, and formed on the surface of food products. Edible films and coating have long been known to protect perishable food products from deterioration and reduce quality loss. These films should have acceptable sensory characteristics, appropriate barrier properties (CO(2), O(2), water, oil), microbial, biochemical and physicochemical stability, they should be safe, and be produced by simple technology in low cost. Also they can act as effective carrier for antioxidant, flavor, color, nutritional or anti-microbial additives. Patents on edible films and food products are also discussed in this article.

  1. Effect of ionizing energy on extracts of Quillaja saponaria to be used as an antimicrobial agent on irradiated edible coating for fresh strawberries

    Energy Technology Data Exchange (ETDEWEB)

    Zuniga, G.E., E-mail: gustavo.zuniga@usach.cl [Universidad de Santiago de Chile (USACH), Facultad de Quimica y Biologia, Depto. de Biologia, Alameda 3363, Estacion Central, Santiago (Chile); Junqueira-Goncalves, M.P., E-mail: mpaula.junqueira@usach.cl [Universidad de Santiago de Chile (USACH), Facultad Tecnologica, Depto. de Ciencia y Tecnologia de Alimentos, Ecuador 3769, Estacion Central, Santiago (Chile); Pizarro, M.; Contreras, R. [Universidad de Santiago de Chile (USACH), Facultad de Quimica y Biologia, Depto. de Biologia, Alameda 3363, Estacion Central, Santiago (Chile); Tapia, A. [Universidad de Santiago de Chile (USACH), Facultad Tecnologica, Depto. de Ciencia y Tecnologia de Alimentos, Ecuador 3769, Estacion Central, Santiago (Chile); Silva, S. [Comision Chilena de Energia Nuclear, Depto. de Aplicaciones Nucleares, Seccion Salud y Alimentos, La Reina, Santiago (Chile)

    2012-01-15

    Incorporating antimicrobial compounds into edible films or coatings provides a novel way to improve the safety and shelf life of ready-to-eat foods. Diverse studies with Quillaja saponaria Mol. (popularly named quillay) extracts have demonstrated their potential as antifungal agents against phytopathogenic fungi. Crosslinking induced by ionizing radiation is an effective method for the improvement of both barrier and mechanical properties of the edible films and coatings based on milk proteins. However there are few reports about the effects of {gamma}-radiation on plant extracts. The aim of this work was to evaluate the effect of ionizing radiation (0, 5, 10, 15, 20, 25 and 35 kGy) on extracts prepared from in vitro plants of Q. saponaria to be used as antimicrobial agent in irradiated edible coating based on calcium caseinate and whey protein isolated, and also to establish the concentration of Q. saponaria extract to be added as an antifungal agent in the coating. Gamma irradiation since 15 kGy affects negatively the antimicrobial activity and metabolites composition of extract of Q. saponaria by reducing compounds of phenolic nature. Otherwise no effect on saponins profile was observed even at higher doses. It was possible to conclude that the antifungal activity of Q. saponaria extract is mainly related to phenolic compounds content. In addition, our work also shows that to obtain an efficient antifungal protection is necessary to add a minimum concentration of 6% of the extract after the coating irradiation. - Highlights: > Antimicrobial compounds into edible coatings improve food' safety and shelf life. > Q. saponaria extract is an antifungal agent against phytopathogenic fungi. > Crosslinking induced by {gamma}-radiation over 30 kGy improves properties of the coatings. > {gamma}-radiation since 15 kGy affects the antimicrobial activity of Q. saponaria extract. > This extract should be added after the coating radiation, at a minimum of 6%.

  2. Effect of ionizing energy on extracts of Quillaja saponaria to be used as an antimicrobial agent on irradiated edible coating for fresh strawberries

    International Nuclear Information System (INIS)

    Zuniga, G.E.; Junqueira-Goncalves, M.P.; Pizarro, M.; Contreras, R.; Tapia, A.; Silva, S.

    2012-01-01

    Incorporating antimicrobial compounds into edible films or coatings provides a novel way to improve the safety and shelf life of ready-to-eat foods. Diverse studies with Quillaja saponaria Mol. (popularly named quillay) extracts have demonstrated their potential as antifungal agents against phytopathogenic fungi. Crosslinking induced by ionizing radiation is an effective method for the improvement of both barrier and mechanical properties of the edible films and coatings based on milk proteins. However there are few reports about the effects of γ-radiation on plant extracts. The aim of this work was to evaluate the effect of ionizing radiation (0, 5, 10, 15, 20, 25 and 35 kGy) on extracts prepared from in vitro plants of Q. saponaria to be used as antimicrobial agent in irradiated edible coating based on calcium caseinate and whey protein isolated, and also to establish the concentration of Q. saponaria extract to be added as an antifungal agent in the coating. Gamma irradiation since 15 kGy affects negatively the antimicrobial activity and metabolites composition of extract of Q. saponaria by reducing compounds of phenolic nature. Otherwise no effect on saponins profile was observed even at higher doses. It was possible to conclude that the antifungal activity of Q. saponaria extract is mainly related to phenolic compounds content. In addition, our work also shows that to obtain an efficient antifungal protection is necessary to add a minimum concentration of 6% of the extract after the coating irradiation. - Highlights: → Antimicrobial compounds into edible coatings improve food' safety and shelf life. → Q. saponaria extract is an antifungal agent against phytopathogenic fungi. → Crosslinking induced by γ-radiation over 30 kGy improves properties of the coatings. → γ-radiation since 15 kGy affects the antimicrobial activity of Q. saponaria extract. → This extract should be added after the coating radiation, at a minimum of 6%.

  3. Novel coating compositions

    International Nuclear Information System (INIS)

    Kimura, Tadashi; Kobayashi, Juichi; Nakamoto, Hideo.

    1969-01-01

    An acrylic coating composition rapidly hardenable by irradiating with ionizing radiations or light beams is given using hydroxyl group-containing vinyl monomers, polycarboxylic acid anhydrides, epoxy group-containing vinyl monomers and an organic solvent having a boiling point of at least 120 0 C. The process comprises the steps of first and second reactions. The first reaction takes place between one mol of a hydroxyl group of a basic polymer and at least 0.1 mol of polycarboxylic acid anhydride, wherein the basic polymer has a molecular weight ranging from 5,000 to 100,000 and consists of 1-40% by weight of vinyl monomer containing hydroxyl group, at least 30% of (meth)acrylic monomer and other vinyl monomers if required. The second reaction takes place between one mol of hydroxyl plus a carboxyl group of the thus obtained basic polymer and at least 0.1 mol of an epoxy group-containing vinyl monomer to produce a prepolymer. The prepolymer is mixed with a solvent such as ethyl benzene to produce the coating material. The electron beam accelerator energy level may be 0.1-2.0 MeV. In light beam polymerization, benzoin is particularly utilized as an intensifying substance. In one example, a basic polymer is produced by reacting 39 parts of styrene, 37 parts of ethyl acrylate, 24 parts of 2-hydroxyl ethyl acrylate, 4 parts of dimethyl amino ethyl methacrylate and others. A prepolymer is produced by reacting this basic polymer with 30 parts of glycidyl acrylate and others. (Iwakiri, K.)

  4. Development and application of edible skin coatings to improve the quality of kinnow during storage

    Directory of Open Access Journals (Sweden)

    Ahmad Din

    2015-01-01

    Full Text Available This study aimed to develop and investigate the effect of application of indigenous skin coating materials for kinnow fruit, which surely would have superior effect on shelf stability and an attractive alternate for inedible coatings. Economical and underutilized sources were explored for this purpose. Eight different formulations were developed to check their suitability through various physico-chemical analyses. It was concluded that edible coating prepared from corn starch, stearic acid, jojoba oil and monoglycerides (T8 was observed best in terms of physico-chemical properties of fruits and significantly increased the shelf life.

  5. Chemical Composition and Bioactive Compounds of Some Wild Edible Mushrooms

    Directory of Open Access Journals (Sweden)

    Melinda NAGY

    2017-05-01

    Full Text Available Over the last decades, the consumption of mushrooms has significantly increased due to the scientific evidence of their ability to help the organism in the combat and prevention of several diseases (Kalac, 2009. Fruiting bodies of mushrooms are consumed as a delicacy for their texture and flavour, but also for their nutritional properties that makes them even more attractable (Heleno S. 2015. In this paper data were collected from several scientific studies with the aim to characterize the chemical composition and content of bioactive compounds of various mushrooms species: Agaricus bisporus, Boletus edulis, Cantharellus cibarius, Pleurotus ostreatus, Lactarius piperatus. The chemical composition of 5 wild edible studied mushrooms, including moisture, ash, total carbohydrates, total sugars, crude fat, crude protein and energy were determined according to AOAC procedures.

  6. Edible Neotropical Blueberries: Antioxidant and Compositional Fingerprint Analysis

    Science.gov (United States)

    DASTMALCHI, KEYVAN; FLORES, GEMA; PETROVA, VANYA; PEDRAZA-PEÑALOSA, PAOLA; KENNELLY, EDWARD J.

    2012-01-01

    Edible blueberry species are well recognized for their potential health benefits. Ericaceae fruits including the North American highbush blueberry (Vaccinium corymbosum L.) and five less common edible blueberry relatives from the New World tropics, Anthopterus wardii Ball, Cavendishia grandifolia Hoerld, Macleania coccoloboides A. C. Sm., Sphyrospermum buxifolium Poepp. & Endl., and Sphyrospermum cordifolium Benth, were investigated for their antioxidant properties and phenolic profiles. The Neotropical berries C. grandifolia and A. wardii exhibited significantly higher DPPH• and ABTS•+ scavenging and iron chelation activities than V. corymbosum. Total phenolic content and HPLC-PDA compositional fingerprint analyses were also carried out. Significant correlations were observed among total phenolic contents, DPPH• and ABTS•+ scavenging, and iron chelation activities. Using HPLC-PDA, the phenolic constituents in the berries were identified as chlorogenic acid, p-coumaric acid, hyperoside, quercetin-3-O-glucoside, isoorientin, isovitexin, orientin and vitexin. Principal components analysis reduced the dimensions of antioxidant and total phenolic data to two components, which accounted for 95% of total variation among the six fruits. Each fruit species formed its own cluster, and therefore the antioxidant profile of each species was shown to be distinct. PMID:21391608

  7. Nutritional composition of Polyrhachis vicina Roger (Edible Chinese black ant

    Directory of Open Access Journals (Sweden)

    Yucui Ren

    2006-03-01

    Full Text Available Edible black ant (Polyrhachis vicina Roger is a traditional edible insect species in China. It has been used as a functional ingredient in various tonics or health foods. This study determined the nutritional composition of the black ant, which included minerals, amino acids, superoxide dismutase (SOD, Vitamin E, and total acid. Supercritical CO2 fluid extraction was used to extract the organic compounds. The compounds were identified and quantified by GC-MS. Results showed that the ant powder contained 77000 IU/100g of SOD, 56.6g/100g protein, 9.0g/100g fat, 13.2g/100g volatile oil, 6.0g/100g moisture, 1.6g/100g total acid and 6.3g/100g ash. There were 18 amino acids, of which, glutamic acid, glycine, aspartic acid, alanine, leucine, proline and tyrosine were predominant. Among the 16 minerals, K, Ca, P, Mg, Fe, Mn and Zn were predominant. More than 20 organic components were identified, the main ones were 9-octadecenoic acid, ethyl oleate, cholesterol and n-hexadecanoic acid. Six of the compounds found, i.e. hexadecanoic acid, ethyl ester, linoleic acid, ethyl oleate, oleic acid and cholesta-3, 5-diene, have not been reported previously. The results indicate that P. vicina Roger is rich in nutrients and is a potential ingredient for health food.

  8. Monitoring of high refractive index edible oils using coated long period fiber grating sensors

    Science.gov (United States)

    Coelho, Luís.; Viegas, Diana; Santos, José Luís.; de Almeida, Jose Manuel M. M.

    2015-05-01

    Monitoring the quality of high refractive index edible oils is of great importance for the human health. Uncooked edible oils in general are healthy foodstuff, olive oil in particular, however, they are frequently used for baking and cooking. High quality edible oils are made from seeds, nuts or fruits by mechanical processes. Nevertheless, once the mechanical extraction is complete, up to 15% of the oil remains in oil pomace and in the mill wastewater, which can be extracted using organic solvents, often hexane. Optical fiber sensors based on long period fiber gratings (LPFG) have very low wavelength sensitivity when the surround refractive index is higher than the refractive index of the cladding. Titanium dioxide (TiO2) coated LPFG could lead to the realization of high sensitivity chemical sensor for the food industry. In this work LPFG coated with a TiO2 thin film were successfully used for to detect small levels of hexane diluted in edible oils and for real time monitoring the thermal deterioration of edible oils. For a TiO2 coating of 30 nm a wavelength sensitivity of 1361.7 nm/RIU (or 0.97 nm / % V/V) in the 1.4610-1.4670 refractive index range was achieved, corresponding to 0 to 12 % V/V of hexane in olive oil. A sensitivity higher than 638 nm/RIU at 225 ºC was calculated, in the 1.4670-1.4735 refractive index range with a detection limit of thermal deterioration of about 1 minute.

  9. APPLICATION OF ANTIOXIDANTS AND EDIBLE STARCH COATING TO REDUCE BROWNING OF MINIMALLY - PROCESSED CASSAVA

    Directory of Open Access Journals (Sweden)

    DANIEL GOMES COELHO

    2017-01-01

    Full Text Available This study aimed to evaluate the quality of minimally - processed cassava treated with antioxidants and a starch - based edible coating. Cassava roots were washed, cooled, immersed in cold water, peeled and then cut. Root pieces were then immersed in a chloride solution, centrifuged, and subsequently immersed in either a starch suspension (3%, a solution containing antioxidants (3% citric acid and 3% ascorbic acid, or in both the coating and antioxidant solutions. Coated root pieces were dried at 18 ± 2°C for 1 hour, then packaged into polypropylene bags (150 g per pack and kept at 5 ± 2°C for 15 days, and assessed every 3 days. A completely randomized design was used in a 4 × 6 factorial consisting of the treatment (control, coating, antioxidant, or coating and antioxidant and the storage period (0, 3 6, 9, 12 or 15 days, with three replicates in each group. The pH, blackened area and peroxidase and polyphenol oxidase activities of the cassava was reduced in treatments containing antioxidants and the scores of visual analysis and phenolic content were higher. Therefore, treatment with antioxidants was effective for reducing browning in minimally - processed cassava, retaining the quality of cassava pieces stored for 15 days at 5 ± 2°C. The combination of antioxidants and the edible coating showed no improvement compared to treatment with antioxidants alone.

  10. Fatty Acid Compositions of Six Wild Edible Mushroom Species

    Science.gov (United States)

    Günç Ergönül, Pelin; Akata, Ilgaz; Kalyoncu, Fatih; Ergönül, Bülent

    2013-01-01

    The fatty acids of six wild edible mushroom species (Boletus reticulatus, Flammulina velutipes var. velutipes, Lactarius salmonicolor, Pleurotus ostreatus, Polyporus squamosus, and Russula anthracina) collected from different regions from Anatolia were determined. The fatty acids were identified and quantified by gas chromatography and studied using fruit bodies. Fatty acid composition varied among species. The dominant fatty acid in fruit bodies of all mushrooms was cis-linoleic acid (18 : 2). Percentage of cis-linoleic acid in species varied from 22.39% to 65.29%. The other major fatty acids were, respectively, cis-oleic, palmitic, and stearic acids. Fatty acids analysis of the mushrooms showed that the unsaturated fatty acids were at higher concentrations than saturated fatty acids. PMID:23844377

  11. Fatty Acid Compositions of Six Wild Edible Mushroom Species

    Directory of Open Access Journals (Sweden)

    Pelin Günç Ergönül

    2013-01-01

    Full Text Available The fatty acids of six wild edible mushroom species (Boletus reticulatus, Flammulina velutipes var. velutipes, Lactarius salmonicolor, Pleurotus ostreatus, Polyporus squamosus, and Russula anthracina collected from different regions from Anatolia were determined. The fatty acids were identified and quantified by gas chromatography and studied using fruit bodies. Fatty acid composition varied among species. The dominant fatty acid in fruit bodies of all mushrooms was cis-linoleic acid (18 : 2. Percentage of cis-linoleic acid in species varied from 22.39% to 65.29%. The other major fatty acids were, respectively, cis-oleic, palmitic, and stearic acids. Fatty acids analysis of the mushrooms showed that the unsaturated fatty acids were at higher concentrations than saturated fatty acids.

  12. Comprehensive chlorophyll composition in the main edible seaweeds.

    Science.gov (United States)

    Chen, Kewei; Ríos, José Julián; Pérez-Gálvez, Antonio; Roca, María

    2017-08-01

    Natural chlorophylls present in seaweeds have been studied regarding their biological activities and health benefit effects. However, detailed studies regarding characterization of the complete chlorophyll profile either qualitatively and quantitatively are scarce. This work deals with the comprehensive spectrometric study of the chlorophyll derivatives present in the five main coloured edible seaweeds. The novel complete MS 2 characterization of five chlorophyll derivatives: chlorophyll c 2 , chlorophyll c 1 , purpurin-18 a, pheophytin d and phytyl-purpurin-18 a has allowed to obtain fragmentation patterns associated with their different structural features. New chlorophyll derivatives have been identified and quantified by first time in red, green and brown seaweeds, including some oxidative structures. Quantitative data of the chlorophyll content comes to achieve significant information for food composition databases in bioactive compounds. Copyright © 2017 Elsevier Ltd. All rights reserved.

  13. Effect of edible coating on the aromatic attributes of roasted coffee beans.

    Science.gov (United States)

    Rattan, Supriya; Parande, A K; Ramalakshmi, K; Nagaraju, V D

    2015-09-01

    Coffee is known throughout the world for its distinct aroma and flavour which results from a number of volatile compounds present in it. It is very difficult to arrest the aromatic compounds once the roasting process is complete and it becomes even more challenging to store the beans for a longer time with the retained volatiles as these compounds are easily lost during industrialized processing such as the grinding of roasted coffee beans and storage of ground coffee. Thus, an attempt was made to minimise the loss of volatile from roasted coffee beans by coating with Carboxymethyl cellulose (CMC), Hydroxypropylmethyl cellulose (HPMC) and Whey protein concentrate. Coffee volatiles were analysed by Gas chromatography and 14 major compounds were identified and compared in this study. Results showed an increase in the relative area of major volatile compounds in coated roasted coffee beans when compared with unroasted coffee beans for consecutive two months. Moreover, effect of coating on textural properties and non-volatiles were also analysed. The results have indicated that edible coatings preserve the sensory properties of roasted coffee beans for a longer shelf life and cellulose derivatives, as an edible coating, exhibited the best protecting effect on roasted coffee beans.

  14. Application of Palm Stearin-Chitosan Edible Coating on Star Fruits (Averrhoa carambola L.)

    International Nuclear Information System (INIS)

    Nurul Hanani Mohamad Zaki; Halimahton Zahrah Mohamed Som; Zaibunnisa Abdul Haiyee

    2012-01-01

    An edible coating comprising of hydrophilic (chitosan) and hydrophobic (palm stearin) components which demonstrated gas barrier and moisture barrier properties respectively, was developed to prolong the post harvest life of star fruits (Averrhoa carambola L.). The physicochemical properties of the coated star fruits were evaluated in terms of weight loss, firmness, visual appearance, colour and glossiness, respiratory gases (oxygen and carbon dioxide) concentrations and ethylene concentration during storage at chilled temperature for 40 days. The results obtained showed that coating reduced weight loss, and maintained firmness and appearance of star fruits. Formulation 1:1 (chitosan:stearin) prevented decline in oxygen production, slowed down carbon dioxide production, and maintained firmness of star fruits. Visual appearance of star fruits showed that coating had lengthened the post harvest life of star fruits up to 40 days with no sign of mould growth. (author)

  15. Review of food composition data for edible insects.

    Science.gov (United States)

    Nowak, Verena; Persijn, Diedelinde; Rittenschober, Doris; Charrondiere, U Ruth

    2016-02-15

    Edible insects are considered rich in protein and a variety of micronutrients, and are therefore seen as potential contributors to food security. However, the estimation of the insects' contribution to the nutrient intake is limited since data are absent in food composition tables and databases. Therefore, FAO/INFOODS collected and published analytical data from primary sources with sufficient quality in the Food Composition Database for Biodiversity (BioFoodComp). Data were compiled for 456 food entries on insects in different developmental stages. A total of 5734 data points were entered, most on minerals and trace elements (34.8%), proximates (24.5%), amino acids (15.3%) and (pro)vitamins (9.1%). Data analysis of Tenebrio molitor confirms its nutritive quality that can help to combat malnutrition. The collection of data will assist compilers to incorporate more insects into tables and databases, and to further improve nutrient intake estimations. Copyright © 2015 Food and Agriculture Organization of the United Nations. Published by Elsevier Ltd.. All rights reserved.

  16. State of the Art of Antimicrobial Edible Coatings for Food Packaging Applications

    Directory of Open Access Journals (Sweden)

    Arantzazu Valdés

    2017-04-01

    Full Text Available The interest for the development of new active packaging materials has rapidly increased in the last few years. Antimicrobial active packaging is a potential alternative to protect perishable products during their preparation, storage and distribution to increase their shelf-life by reducing bacterial and fungal growth. This review underlines the most recent trends in the use of new edible coatings enriched with antimicrobial agents to reduce the growth of different microorganisms, such as Gram-negative and Gram-positive bacteria, molds and yeasts. The application of edible biopolymers directly extracted from biomass (proteins, lipids and polysaccharides or their combinations, by themselves or enriched with natural extracts, essential oils, bacteriocins, metals or enzyme systems, such as lactoperoxidase, have shown interesting properties to reduce the contamination and decomposition of perishable food products, mainly fish, meat, fruits and vegetables. These formulations can be also applied to food products to control gas exchange, moisture permeation and oxidation processes.

  17. Radiation-curable coating composition

    International Nuclear Information System (INIS)

    Mibae, Jiro; Kawamura, Hiroshi; Takahashi, Masao.

    1970-01-01

    A radiation-curable coating composition, suitable for metal precoating, is provided. The composition is prepared by mixing 50 to 90 parts of a long chain fatty acid ester (A) with 10 to 50 parts of monomer (B) which is copolymerizable with (A). (A) is prepared by reacting a dimer acid (particularly the dimer of linolenic acid) with hydroxyalkyl methacrylate or glycidyl methacrylate. Upon irradiation with electron beams (0.1 to 3 MeV) the composition cures to yield a coating of high adhesion, impact resistance and bending resistance. In one example, 100 g of dimer acid (Versadime 216, manufactured by General Mills) was esterified with 50 g of 2-hydroxyethyl methacrylate. A zinc plated iron plate was coated with the product and irradiated with electron beams (2 Mrad). Pencil hardness was F; adhesion 0: impact resistance (Du Pont) 1 kg x 30 cm; bending resistance 2T. (Kaichi, S.)

  18. Development of Bioactive Edible Coatings and Biodegradable Packaging Using Gamma Irradiation

    International Nuclear Information System (INIS)

    Lacroix, M.; Salmieri, S.

    2010-01-01

    Gamma irradiation was used to cross-link milk proteins in order to enhance the physico-chemical properties of edible films made of calcium caseinate, whey protein isolate and glycerol. Fourier Transform Infrared analysis was used to characterize the conformation of proteins adopted after irradiation. The molecular weight of cross-linked proteins was measured by Size-Exclusion Chromatography. Furthermore, the effect of the addition of methylcellulose to the irradiated protein matrix on the rheological properties (puncture strength, puncture deformation and water vapor permeability) of films was also studied. Moreover, cross-linking of polysaccharides under paste-like state was investigated and the cross-linking degree of the gel products was determined by gel fraction measurements and solubility percentage. In order to prepare bioactive coatings, several antifungal compounds were evaluated as bioactive compounds in order to select one of them to prepare an antimicrobial solution to spray onto strawberries or to encapsulate them in film formulations composed of milk proteins and methylcellulose based films. In addition, the bioactive coatings containing the antifungals were used to increase the radiosensitivity under air of moulds and total flora in strawberries and the relative sensitivity of selected formulations was calculated from their D10 value. The film formulation selected was used as a bioactive edible coating in order to determine their efficiency to increase the shelf life of fresh strawberries and to preserve their quality during storage. (author)

  19. Application of edible coating with starch and carvacrol in minimally processed pumpkin.

    Science.gov (United States)

    Santos, Adriele R; da Silva, Alex F; Amaral, Viviane C S; Ribeiro, Alessandra B; de Abreu Filho, Benicio A; Mikcha, Jane M G

    2016-04-01

    The present study evaluated the effect of an edible coating of cassava starch and carvacrol in minimally processed pumpkin (MPP). The minimal inhibitory concentration (MIC) of carvacrol against Escherichia coli, Salmonella enterica serotype Typhimurium, Aeromonas hydrophila, and Staphylococcus aureus was determined. The edible coating that contained carvacrol at the MIC and 2 × MIC was applied to MPP, and effects were evaluated with regard to the survival of experimentally inoculated bacteria and autochthonous microflora in MPP. Total titratable acidity, pH, weight loss, and soluble solids over 7 days of storage under refrigeration was also analyzed. MIC of carvacrol was 312 μg/ml. Carvacrol at the MIC reduced the counts of E. coli and S. Typhimurium by approximately 5 log CFU/g. A. hydrophila was reduced by approximately 8 log CFU/g, and S. aureus was reduced by approximately 2 log CFU/g on the seventh day of storage. Carvacrol at the 2 × MIC completely inhibited all isolates on the first day of Storage. coliforms at 35 °C and 45 °C were not detected (< 3 MPN/g) with either treatment on all days of shelf life. The treatment groups exhibited a reduction of approximately 2 log CFU/g in psychrotrophic counts compared with controls on the last day of storage. Yeast and mold were not detected with either treatment over the same period. The addition of carvacrol did not affect total titratable acidity, pH, or soluble solids and improved weight loss. The edible coating of cassava starch with carvacrol may be an interesting approach to improve the safety and microbiological quality of MPP.

  20. Application of Essential Oils from Galanga Rhizome in Edible Coating Carrageenan as Antibacterial on Tilapia Fishball

    Directory of Open Access Journals (Sweden)

    Fajar Bayu Senoaji

    2017-08-01

    Full Text Available Fish ball is a perishable food product. One of an alternative method which could be applied to delay the deterioration process was using carrageenan edible coating with the addition of galangal rhizome’s essential oil as an antibacterial agent. The aim of this study was to find out whether the addition of carrageenan edible coating with galangal rhizome’s essential oil could increase the shelf life of the tilapia fish ball during cold storage or not. This study was used experimental laboratories with the completely randomized design used factorial (2x6 two factors include essential oils concentrations (0%, dan 1% and storage time (0, 3, 6, 9, 12, 15 with three repetitions. The shelf life of the fish ball observed by sensory, TPC, TVBN, pH, Aw, moisture content, and gel strength test. The parametric data were analyzed by the ANOVA, while the non-parametric was using the Kruskal Wallis test. As the result, the fish ball with the 1% treatment was still acceptable until 15 days of storage compared with the control which only lasts for 9 days. The other results were the sensory test was 6.63≤π≤6.95, TPC value was 1.07x105 cfu/g, TVBN value was 30.33±1.68 mgN%, the moisture content was 61.38%±0.47, the Aw was 0.89±0.006, the pH was 6.24±0.0, and the gel strength was 721.19±1.61 g.cm. The treatment of 1% essential oil addition to carrageenan edible coating was significantly different (p<0.05 compared to the control treatment during cold storage to the characteristic of tilapia fish ball.

  1. Antimicrobial edible coatings and films from micro-emulsions and their food applications.

    Science.gov (United States)

    Guo, Mingming; Yadav, Madhav P; Jin, Tony Z

    2017-12-18

    This study focused on the use of antimicrobial edible coatings and films from micro-emulsions to reduce populations of foodborne pathogens in foods. Corn-Bio-fiber gum (C-BFG) was used as an emulsifier with chitosan. Allyl isothiocyanate (AIT) and lauric arginate ester (LAE) served as antimicrobials. Micro-emulsions were obtained from a solution consisting of 1% chitosan, 0.5% C-BFG, and 1-4% AIT or LAE which was subject to high pressure homogenization (HPH) processing at 138MPa for 3cycles. Coatings and films produced from the micro-emulsions had micro-pores with sizes ranging from 100 to 300nm and micro-channels that hold antimicrobials effectively and facilitate the release of antimicrobials from the center to the surface of the films or coatings, thus enhancing their antimicrobial efficacy. The coatings and films with 1% AIT reduced populations of Listeria innocua by over 5, 2, and 3 log CFU in culture medium (Tryptic soy broth, TSB), ready-to-eat meat, and strawberries, respectively. The coatings and films with 1% LAE reduced populations of Escherichia coli O157:H7 and Salmonella spp. by over 5 and 2 log CFU in TSB and strawberries, respectively. This study provides an innovative approach for the development of effective antimicrobial materials to reduce food borne pathogenic contaminants on ready-to-eat meat, strawberries, or other food. Published by Elsevier B.V.

  2. Layer-by-Layer Alginate and Fungal Chitosan Based Edible Coatings Applied to Fruit Bars.

    Science.gov (United States)

    Bilbao-Sainz, Cristina; Chiou, Bor-Sen; Punotai, Kaylin; Olson, Donald; Williams, Tina; Wood, Delilah; Rodov, Victor; Poverenov, Elena; McHugh, Tara

    2018-05-30

    Food waste is currently being generated at an increasing rate. One proposed solution would be to convert it to biopolymers for industrial applications. We recovered chitin from mushroom waste and converted it to chitosan to produce edible coatings. We then used layer-by-layer (LbL) electrostatic deposition of the polycation chitosan and the polyanion alginate to coat fruit bars enriched with ascorbic acid. The performance of the LbL coatings was compared with those containing single layers of fungal chitosan, animal origin chitosan and alginate. Bars containing alginate-chitosan LbL coatings showed increased ascorbic acid content, antioxidant capacity, firmness and fungal growth prevention during storage. Also, the origin of the chitosan did not affect the properties of the coatings. Mushroom stalk bases could be an alternative source for isolating chitosan with similar properties to animal-based chitosan. Also, layer-by-layer assembly is a cheap, simple method that can improve the quality and safety of fruit bars. © 2018 Institute of Food Technologists®.

  3. The Functionalization of Nanostructures and Their Potential Applications in Edible Coatings

    Directory of Open Access Journals (Sweden)

    Ricardo M. González-Reza

    2018-04-01

    Full Text Available Nowadays, edible coatings incorporated with nanostructures as systems of controlled release of flavors, colorants and/or antioxidants and antimicrobial substances, also used for thermal and environmental protection of active compounds, represent a gap of opportunity to increase the shelf life of food highly perishable, as well as for the development of new products. These functionalized nanostructures have the benefit of incorporating natural substances obtained from the food industry that are rich in polyphenols, dietary fibers, and antimicrobial substances. In addition, the polymers employed on its preparation, such as polysaccharides, solid lipids and proteins that are low cost and developed through sustainable processes, are friendly to the environment. The objective of this review is to present the materials commonly used in the preparation of nanostructures, the main ingredients with which they can be functionalized and used in the preparation of edible coatings, as well as the advances that these structures have represented when used as controlled release systems, increasing the shelf life and promoting the development of new products that meet the characteristics of functionality for fresh foods ready to eat.

  4. Shelf-life of fresh blueberries coated with quinoa protein/chitosan/sunflower oil edible film.

    Science.gov (United States)

    Abugoch, Lilian; Tapia, Cristián; Plasencia, Dora; Pastor, Ana; Castro-Mandujano, Olivio; López, Luis; Escalona, Victor H

    2016-01-30

    The aim of this study was to evaluate quinoa protein (Q), chitosan (CH) and sunflower oil (SO) as edible film material as well as the influence of this coating in extending the shelf-life of fresh blueberries stored at 4 °C and 75% relative humidity. These conditions were used to simulate the storage conditions in supermarkets and represent adverse conditions for testing the effects of the coating. The mechanical, barrier, and structural properties of the film were measured. The effectiveness of the coating in fresh blueberries (CB) was evaluated by changes in weight loss, firmness, color, molds and yeast count, pH, titratable acidity, and soluble solids content. The tensile strength and elongation at break of the edible film were 0.45 ± 0.29 MPa and 117.2% ± 7%, respectively. The water vapor permeability was 3.3 × 10(-12) ± 4.0 × 10(-13) g s(-1) m(-1) Pa(-1). In all of the color parameters CB presented significant differences. CB had slight delayed fruit ripening as evidenced by higher titratable acidity (0.3-0.5 g citric acid 100 g(-1)) and lower pH (3.4-3.6) than control during storage; however, it showed reduced firmness (up to 38%). The use of Q/CH/SO as a coating in fresh blueberries was able to control the growth of molds and yeasts during 32 days of storage, whereas the control showed an increasing of molds and yeast, between 1.8 and 3.1 log cycles (between 20 and 35 days). © 2015 Society of Chemical Industry.

  5. Evaluation of resistant starch, glycemic index and fortificants content of premix rice coated with various concentrations and types of edible coating materials

    Science.gov (United States)

    Yulianto, W. A.; Susiati, A. M.; Adhini, H. A. N.

    2018-01-01

    The incidence of diabetes in Indonesia has been increasing year by year. Diets with a low glycemic index and high resistant starch foods can assist diabetics in controlling their blood glucose levels. Diabetics are known to have micro-nutrient deficiencies of chromium, magnesium and vitamin D that can be overcome by consuming parboiled rice fortified by use of a coating method. The fortification of parboiled rice (premix rice) can be achieved by coating with HPMC (hydroxypropyl methyl cellulose), MC (methyl cellulose), CMC (carboxyl methyl cellulose), gum arabic and rice starch. This research aimed to evaluate the levels of resistant starch, glycemic index and fortificants of premix rice coated with different concentrations and types of edible coating materials. This research used completely randomized design, with treatments to the concentrations and the types of edible coating (HPMC, CMC, MC, gum arabic and rice starch). The concentrations of edible coating were 0.15%, 0.2% and 0.25% for cellulose derivative coatings; 25%, 30%, 35% for gum arabic and 2%, 3.5% and 5% for rice starch. This research shows that fortified premix rice coated with various concentrations and types of edible coating materials is high in resistant starch and has a low glycemic index. The coating treatment affects the levels of magnesium and vitamin D, but does not affect the levels of chromium in parboiled rice. The premix rice with a low glycemic index and high nutrient content (chromium, magnesium and vitamin D) was premix rice coated by CMC 0.25% and HPMC 0.25% with glycemic indeces of 39.34 and 38.50, respectively.

  6. Compositional and physicochemical factors governing the viability of Lactobacillus rhamnosus GG embedded in starch-protein based edible films

    Science.gov (United States)

    Soukoulis, Christos; Singh, Poonam; Macnaughtan, William; Parmenter, Christopher; Fisk, Ian D.

    2016-01-01

    Probiotic incorporation in edible films and coatings has been shown recently to be an efficient strategy for the delivery of probiotics in foods. In the present work, the impact of the compositional, physicochemical and structural properties of binary starch-protein edible films on Lactobacillus rhamnosus GG viability and stability was evaluated. Native rice and corn starch, as well as bovine skin gelatine, sodium caseinate and soy protein concentrate were used for the fabrication of the probiotic edible films. Starch and protein type both impacted the structural, mechanical, optical and thermal properties of the films, and the process loss of L. rhamnosus GG during evaporation-dehydration was significantly lower in the presence of proteins (0.91–1.07 log CFU/g) compared to solely starch based systems (1.71 log CFU/g). A synergistic action between rice starch and proteins was detected when monitoring the viability of L. rhamnosus GG over four weeks at fridge and room temperature conditions. In particular, a 3- to 7-fold increase in the viability of L. rhamnosus GG was observed in the presence of proteins, with sodium caseinate – rice starch based films offering the most enhanced stability. The film's shelf-life (as calculated using the FAO/WHO (2011) basis of 6 log viable CFU/g) ranged between 27-96 and 15–24 days for systems stored at fridge or room temperature conditions respectively. PMID:26726280

  7. Radiation curable compositions useful as transfer coatings

    International Nuclear Information System (INIS)

    McCarty, W.H.; Nagy, F.A.; Guarino, J.P.

    1983-01-01

    The invention is on a method for applying a coating to a thin porous substrate and reducing absorption of the coating into the substrate by applying a radiation-curable composition to a carrying web; the radiation-curable coating composition having a crosslink density of 0.02 to about 1.0 determined by calculation of the gram moles of branch points per 100 grams of uncured coating, and a glass transition temperature of the radiation cured coating within the approximate range of -80 degrees to +100 degrees C. The carrying web being of a nature such that the coating composition, when cured, will not adhere to its surface

  8. Consumer profile and acceptability of cooked beef steaks with edible and active coating containing oregano and rosemary essential oils.

    Science.gov (United States)

    Vital, Ana Carolina Pelaes; Guerrero, Ana; Kempinski, Emilia Maria Barbosa Carvalho; Monteschio, Jessica de Oliveira; Sary, Cesar; Ramos, Tatiane Rogelio; Campo, María Del Mar; Prado, Ivanor Nunes do

    2018-09-01

    Fresh animal products are highly perishable and characterized by a short shelf-life. Edible coatings with natural antioxidants (essential oils: EOs) could improve stability, ensure quality, and increase the shelf-life of fresh products. Due to the strong flavor of EOs, their use should consider consumer preferences and sensory acceptability. This study evaluated the effects of edible coating (with oregano and rosemary essential oil) on beef in relation to consumer preferences, besides the determination of habits of consumption and buying intentions of consumers. Acceptability scores from three clusters of consumers was described. Coating with oregano was the preferred. The higher consumer acceptance and willingness to buy this product indicate a great potential and possibility of using coatings with essential oils in fresh animal products. Copyright © 2018. Published by Elsevier Ltd.

  9. EDIBLE COATING BERBASIS PATI SAGU DENGAN PENAMBAHAN ANTIMIKROBA MINYAK SEREH PADA PAPRIKA: PREFERENSI KONSUMEN DAN MUTU VITAMIN C

    Directory of Open Access Journals (Sweden)

    Widaningrum Widaningrum

    2015-05-01

    vitamin C pada paprika dengan perlakuan 0,4% minyak sereh pada suhu 8°C pada hari penyimpanan ke-27 masih tetap tinggi yaitu 1,5 mg/100g. Kata kunci: Paprika, edible coating, preferensi konsumen, vitamin C

  10. Effect of cassava starch-based edible coating incorporated with lemongrass essential oil on the quality of papaya MJ9

    Science.gov (United States)

    Praseptiangga, D.; Utami, R.; Khasanah, L. U.; Evirananda, I. P.; Kawiji

    2017-02-01

    Edible films and coatings have emerged as an alternative packaging in food applications and have received much attention due to their advantages. The incorporation of essential oils in film matrices to give antimicrobial properties had been observed recently, and could be used as promising preservation technology. In this study, cassava starch-based edible coating incorporated with lemongrass essential oil (1%) was applied by spraying and dipping methods to preserve papaya MJ9 during storage at room temperature. The quality of papaya MJ9 was analyzed based on its physicochemical and microbiological properties. The addition of lemongrass essential oil (1%) significantly inhibited the microbial growth on papaya MJ9 by reducing the value of total yeast and mold as compared to the control. This study also showed that for parameters of weight loss, total soluble solid, vitamin C, and total titratable acid, papaya MJ9 with cassava starch-based edible coating incorporated with lemongrass essential oil (1%) had the lower values than control, however, they had the higher value than control on firmness parameter. These results indicate that cassava starch-based edible coating incorporated with lemongrass essential oil (1%) can be used as an alternative preservation for papaya MJ9.

  11. Effects of Polysaccharide-Based Edible Coatings on Quality and Antioxidant Enzyme System of Strawberry during Cold Storage

    Directory of Open Access Journals (Sweden)

    Li Li

    2017-01-01

    Full Text Available Strawberry is a nutritious, but highly perishable fruit. Three polysaccharide-based edible coatings (alginate, chitosan, and pullulan were applied to postharvest strawberry fruit during cold storage (4°C, and their effects on fruit quality and antioxidant enzyme system were investigated in the present study. The results showed that polysaccharide coatings showed a significant delay in fruit softening and rot and reduced changes in total soluble solid and titratable acidity content during 16 d storage. Polysaccharide coatings also maintained higher ascorbic acid and total phenolic contents than control from day 2 and significantly inhibited fruit decay and respiration after 12 d storage (p<0.05. Polysaccharide treatments enhanced the activities of antioxidant enzymes (peroxidase, catalase, superoxide dismutase, and ascorbate peroxidase so as to prevent lipid peroxidation and reduce membrane damage. Additionally, chitosan coating had the most positive effects on fruit quality amongst three polysaccharide-based edible coatings and presented the highest relative activities of antioxidant enzymes. These results indicated that polysaccharide-based edible coatings were helpful in postharvest quality maintenance of strawberry fruit.

  12. Effects of Edible Chitosan Coating on Quality and Increasing Storage Life of Cucumber cv.

    Directory of Open Access Journals (Sweden)

    M. Ghasemi Tavallaiy

    2015-06-01

    Full Text Available Chitosan, is non-toxic, biodegradable and biocompatible material, which can be used as edible coatings to maintain quality and enhance postharvest life of fruits and vegetables. In this study, the effect of chitosan at 0, 0.5, 1 and 2% concentrations on storage life of cucumber cv. "Zomorod" was investigated. After treatment and keeping in an incubator at 12 °C and 90% relative humidity, the fruits were assessed in 5-days intervals to determine parameters such as firmness, weight loss, vitamin C, titratable acidity, soluble solids and chlorophyll content. Experiment was performed as a split-plot design in time in a completely randomized design with three replications. The results of the experiment showed that chitosan coating, had a significant effect on all traits except titrable acidity. The lowest weight loss and the highest firmness were recorded with 1% chitosan treatment which significantly differed from the control. It is appeared that chitosan coatings could be used to increase the storage life of cucumber fruit and to maintain its quality for a longer period.

  13. Fatty acid composition of commercially available Iranian edible oils

    Directory of Open Access Journals (Sweden)

    Sedigheh Asgary

    2009-08-01

    several studies reported multiple adverse effects of TFAs on human health, limited  nformation is available about total fatty acid composition, particularly TFAs, in Iranian edible oils. Our findings indicated higher content of TFAs in Iranian commercially available PHVOs.

  • KEYWORDS: Fatty Acids, Vegetable Oils, Trans Fats.
  • PENGARUH PENGGUNAAN LAPISAN EDIBEL (EDIBLE COATING, KALSIUM KLORIDA, DAN KEMASAN PLASTIK TERHADAP MUTU NANAS (Ananas comosus Merr. TEROLAH MINIMAL

    Directory of Open Access Journals (Sweden)

    Indera Sakti Nasution

    2012-06-01

    Full Text Available The problem that often occurs before consuming fresh pineapple is it takes a long time to peel the pineapple. Minimal processing of pineapple is one of the solutions for practical use by consumers who would like to consume it fresh. However, minimally processed pineapple will be easily damaged and has short shelf life. The aims of this study are to determine the quality of minimally processed pineapple coated with edible coating, effect of calcium chloride dipping, as well as plastic packaging at low temperatures storage. Combination of Cassava starch and glycerol used as edible coating for pineapple dipped in CaCl2for 1 minute and 2 minutes, respectively. Products were packaged using polyethylene, polypropylene, and without packaging. It is obtained that dipping the product in CaCl2 for 2 minutes and packaging it using polypropylene (plastic can prolong the shelf life of minimally processed pineapple stored at 5°C up to 8 days.

  • Postharvest shelf-life extension of pink guavas (Psidium guajava L.) using HPMC-based edible surface coatings.

    Science.gov (United States)

    Vishwasrao, Chandrahas; Ananthanarayan, Laxmi

    2016-04-01

    Psidium guajava L. var. 'Lalit' is a perishable fruit with delicate skin which is prone to damage. The objective of this study was to determine the effect of edible coating made up of hydroxypropyl methyl cellulose and palm oil on ripening of guava. Coating solution was applied over fruits and coated fruits were stored at 24 ± 1 °C and 65 ± 5%RH. Changes in fruit colour, texture softening, respiration rate, weight loss, ascorbic acid content, soluble solids, titrable acidity, chlorophyll content, total reducing sugars, total phenolic content were studied during post-harvest ripening. Fruits coated with 1 % of hydroxypropyl methyl cellulose and 0.3 % of palm oil showed significant delay in weight loss, fruit firmness as well as colour change (p < 0.05). Coating delayed the enzyme activities of peroxidase and polyphenol oxidase of the fruit. Results suggest that overall quality of coated fruit was maintained by edible coating formulation extending the shelf life of fruit up to 12 days with appreciable retention of all quality parameters tested.

  • Antimicrobial Edible Films and Coatings for Meat and Meat Products Preservation

    Directory of Open Access Journals (Sweden)

    Irais Sánchez-Ortega

    2014-01-01

    Full Text Available Animal origin foods are widely distributed and consumed around the world due to their high nutrients availability but may also provide a suitable environment for growth of pathogenic and spoilage microorganisms. Nowadays consumers demand high quality food with an extended shelf life without chemical additives. Edible films and coatings (EFC added with natural antimicrobials are a promising preservation technology for raw and processed meats because they provide good barrier against spoilage and pathogenic microorganisms. This review gathers updated research reported over the last ten years related to antimicrobial EFC applied to meat and meat products. In addition, the films gas barrier properties contribute to extended shelf life because physicochemical changes, such as color, texture, and moisture, may be significantly minimized. The effectiveness showed by different types of antimicrobial EFC depends on meat source, polymer used, film barrier properties, target microorganism, antimicrobial substance properties, and storage conditions. The perspective of this technology includes tailoring of coating procedures to meet industry requirements and shelf life increase of meat and meat products to ensure quality and safety without changes in sensory characteristics.

  • Cationic electrodepositable coating composition comprising lignin

    Science.gov (United States)

    Fenn, David; Bowman, Mark P; Zawacky, Steven R; Van Buskirk, Ellor J; Kamarchik, Peter

    2013-07-30

    A cationic electrodepositable coating composition is disclosed. The present invention in directed to a cationic electrodepositable coating composition comprising a lignin-containing cationic salt resin, that comprises (A) the reaction product of: lignin, an amine, and a carbonyl compound; (B) the reaction product of lignin, epichlorohydrin, and an amine; or (C) combinations thereof.

  • The effect of various concentration of tilapia (Oreochromis sp.) surimi for edible coating on the shelf-life of Pangasius sp. fillets

    Science.gov (United States)

    Purnama, M. A. P.; Agustono; Sahidu, A. M.

    2018-04-01

    Pangasius sp. fillets prone to deterioration the quality that will affect the appearance and the shelf life of fillets. The effort to extend the shelf life of fish fillet that is by using an edible coating. Surimi can be used as a protein-based edible coating because they have superior inhibitory and mechanical properties compared to the polysaccharides based material. Surimi can be made from freshwater tilapia (Oreochromis sp.) fish. The experimental design used was Completely Randomized Design (CRD) with five treatments of surimi (0 gr, 2 gr, 4 gr, 6 gr, 8 gr) with four replications. The results showed that Pangasius sp. fillets with an edible coating 8 gr surimi have the highest value in the organoleptic test. The pH testing on Pangasius sp. fillets with edible coating 2 gr, 4 gr, 6 gr, and 8 gr surimi from the 0th hour to 18th hour have increased but slower than Pangasius sp. fillets without edible coating surimi. The best value of Total Plate Count (TPC) test is in edible coating 6 gr and 8 gr surimi as it is in accordance with SNI 2696:2013 at room temperature storage until the 18th hours.

  • Synergistic Effect of Sodium Chlorite and Edible Coating on Quality Maintenance of Minimally Processed Citrus grandis under Passive and Active MAP.

    Science.gov (United States)

    Ban, Zhaojun; Feng, Jianhua; Wei, Wenwen; Yang, Xiangzheng; Li, Jilan; Guan, Junfeng; Li, Jiang

    2015-08-01

    Edible coating has been an innovation within the bioactive packaging concept. The comparative analysis upon the effect of edible coating, sodium chlorite (SC) and their combined application on quality maintenance of minimally processed pomelo (Citrus grandis) fruits during storage at 4 °C was conducted. Results showed that the combination of edible coating and SC dipping delayed the microbial development whereas the sole coating or dipping treatment was less efficient. The synergetic application of edible coating and SC treatment under modified atmosphere packaging (MAP, 10% O2 , 10% CO2 ) was able to maintain the total soluble solids level and ascorbic acid content, while reduce the weight loss as well as development of mesophiles and psychrotrophs. Nonetheless, the N, O-carboxymethyl chitosan solely coated samples showed significantly higher level of weight loss during storage with comparison to the untreated sample. Furthermore, the combined application of edible coating and SC dipping under active MAP best maintained the sensory quality of minimally processed pomelo fruit during storage. © 2015 Institute of Food Technologists®

  • The Effect of the Application of Edible Coatings on or before Ultraviolet Treatment on Postharvested Longan Fruits

    Directory of Open Access Journals (Sweden)

    Mee Gie Lin

    2017-01-01

    Full Text Available This study compared the effect of application of edible coating on or before ultraviolet treatment on postharvest longan fruits. The treated longan fruits were examined for weight loss, respiration rate, surface color changes, enzymatic activities (PPO, POD, and PAL, and total phenolic contents throughout the 7 storage days at ambient temperature. In addition, coat homogeneity was examined and cell structure of longan flesh at the end of storage was observed. The results showed that when UV was applied before coating (i.e., chitosan or carrageenan, it had relatively lower PPO and PAL activities and retained higher TPC in longan pericarp. However, the changes in enzymatic activities did not affect the surface lightness and browning index as they were more influenced by the type of coating, in which combination treatments with carrageenan showed higher surface lightness and lower browning index compared to treatment combinations containing chitosan. However, when UV treatment preceded coating, the combinations of UV plus chitosan coating produced lower PPO and PAL activities and retained better cell structure with less damage than the combinations of UV plus carrageenan coating. UV plus carrageenan coating showed relatively higher weight loss and respiration rate, with cell structure exhibiting bigger intercellular spaces at the end of storage. Therefore, application of UV treatment followed by chitosan coating was found to be the best treatment combination for controlling enzymatic activities and reducing senescence rate of longan fruits.

    1. Effects of tartary buckwheat polysaccharide combined with nisin edible coating on the storage quality of tilapia (Oreochromis niloticus) fillets.

      Science.gov (United States)

      Wang, Fengping; Zhang, Huijun; Jin, Wengang; Li, Lirong

      2018-06-01

      To investigate the effect of tartary buckwheat polysaccharide (TBP) combined with nisin edible coatings on the preservation of tilapia (Oreochromis niloticus) fillets, fillets were dip treated with different concentrations of TBP (5, 10 and 15 g kg -1 ) combined with nisin and stored at 4 °C for 12 days. The pH values, thiobarbituric acid contents, total volatile base nitrogen (TVB-N) content, total viable count (TVC), surface colors, textures and sensory properties of the tilapia fillets at storage were all periodically investigated. TBP combined with nisin-treated groups significantly improved the bacteriological, physicochemical, and sensory characteristics of the tilapia fillets to a greater extent compared to the control group and presented better quality preservation effects than nisin coating alone. Based on the limits of the TVB-N, TVC and sensory scores, the shelf life of the control tilapia fillets was 4 days, whereas that for nisin with TBP-coated fillets was 8-10 days. Edible coatings made from TBP combined with nisin are suitable for maintaining qualities and enhancing the shelf lives of tilapia fillets stored at 4 °C. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

    2. Nickel and titanium nanoboride composite coating

      International Nuclear Information System (INIS)

      Efimova, K A; Galevsky, G V; Rudneva, V V; Kozyrev, N A; Orshanskaya, E G

      2015-01-01

      Electrodeposition conditions, structural-physical and mechanical properties (microhardness, cohesion with a base, wear resistance, corrosion currents) of electroplated composite coatings on the base of nickel with nano and micro-powders of titanium boride are investigated. It has been found out that electro-crystallization of nickel with boride nanoparticles is the cause of coating formation with structural fragments of small sizes, low porosity and improved physical and mechanical properties. Titanium nano-boride is a component of composite coating, as well as an effective modifier of nickel matrix. Nano-boride of the electrolyte improves efficiency of the latter due to increased permissible upper limit of the cathodic current density. (paper)

    3. The friction wear of electrolytic composite coatings

      International Nuclear Information System (INIS)

      Starosta, R.

      2002-01-01

      The article presents the results of investigation of wear of galvanic composite coatings Ni-Al 2 O 3 and Ni-41%Fe-Al 2 O 3 . The diameter of small parts of aluminium oxide received 0.5; 3; 5 μm. Investigations of friction sliding were effected on PT3 device at Technical University of Gdansk. Counter sample constituted a funnel made of steel NC6 (750 HV). Increase of wear coatings together with the rise of iron content in matrix is observed. The rise of sizes of ceramic particles caused decrease of wear of composite coatings, but rise of steel funnel wear. The friction coefficient increased after ceramic particle s were built in coatings. The best wear resistance characterized Ni-41%Fe-Al 2 O 3 coatings containing 2.2x10 6 mm -2 ceramic particles. (author)

    4. Effect of thinning on flower and fruit and of edible coatings on postharvest quality of jaboticaba fruit stored at low temperature

      Directory of Open Access Journals (Sweden)

      Talita Pimenta do Nascimento

      2013-09-01

      Full Text Available Jaboticaba is a Brazilian fruit, native to the Atlantic forest, which belongs to the Myrtaceae family. In this work we describe the effect of the thinning of "flower", "fruit" and "flower & fruit" compared to non-thinned fruit (control and of edible coatings with respect on nutritional composition, overall acceptability and shelf-life of jaboticaba ‘Sabara’, grown in an irrigated commercial orchard. "Flower and fruit" thinning allows fruit with higher quality as diameter, volume and mass. Non-thinned fruit shows higher yield, however fruit have lower quality. As a result of the improving quality at harvest, the shelf life was twice (~8 days for thinned fruit. The lack of change in concentration of soluble sugar and absence of formation of volatile compounds during storage indicate that there was no natural fermentation of the jaboticaba pulp after harvest. Treatments with wax and calcium did not improve the jaboticaba shelf life.

    5. Recent advances in modified atmosphere packaging and edible coatings to maintain quality of fresh-cut fruits and vegetables.

      Science.gov (United States)

      Ghidelli, Christian; Pérez-Gago, María B

      2018-03-04

      Processing of fruits and vegetables generates physiological stresses in the still living cut tissue, leading to quality deterioration and shorter shelf life as compared with fresh intact produces. Several strategies can be implemented with the aim to reduce the rate of deterioration of fresh-cut commodities. Such strategies include low temperature maintenance from harvest to retail and the application of physical and chemical treatments such as modified atmosphere packaging (MAP) with low O 2 and high CO 2 levels and antioxidant dips. Other technologies such as edible coatings with natural additives, new generation of coatings using nanotechnological solutions such as nanoparticles, nanoencapsulation, and multilayered systems, and nonconventional atmospheres such as the use of pressurized inert/noble gases and high levels of O 2 have gained a lot of interest as a possibility to extend the shelf life of minimally processed fruits and vegetables. However, the high perishability of these products challenges in many cases their marketability by not achieving sufficient shelf life to survive the distribution system, requiring the combination of treatments to assure safety and quality. This review reports the recent advances in the use of MAP, edible coatings, and the combined effect of both technologies to extend the shelf life of fresh-cut fruits and vegetables.

    6. Thyme and basil essential oils included in edible coatings as a natural preserving method of oilseed kernels.

      Science.gov (United States)

      Riveros, Cecilia G; Nepote, Valeria; Grosso, Nelson R

      2016-01-15

      Sunflower seeds are susceptible to developing rancidity and off-flavours through lipid oxidation. Edible coatings and essential oils have proven antioxidant properties in different food products. The purpose of this study was to evaluate the combined effect of using an edible coating and thyme and basil essential oils to preserve the chemical and sensory quality parameters of roasted sunflower seeds during storage. 50% DPPH inhibitory concentration (IC50) values of 0.278 and 0.0997 µg mL(-1) were observed for thyme and basil, respectively. On storage day 40, peroxide values were 80.68, 70.28, 68.43, 49.31 and 33.87 mEq O2 kg(-1) in roasted sunflower seeds (RS), roasted sunflower seeds coated with carboxymethyl cellulose (CMC) (RS-CMC), roasted sunflower seeds coated with CMC added with basil (RS-CMC-A), thyme (RS-CMC-T) and butylated hydroxytoluene (RS-CMC-BHT), respectively. RS-CMC-T and RS-CMC-BHT presented the lowest peroxide values, conjugated dienes and p-anisidine values during storage. RS-CMC-BHT, RS-CMC-T, and RS-CMC-A showed the lowest oxidized and cardboard flavour intensity ratings. On storage day 40, roasted sunflower flavour intensity ratings were higher in RS-CMC-T and RS-CMC-A. Thyme and basil essential oils added to the CMC coating improved the sensory stability of this product during storage, but only thyme essential oil increased their chemical stability. © 2015 Society of Chemical Industry.

    7. Prior frozen storage enhances the effect of edible coatings against Listeria monocytogenes on cold-smoked salmon during subsequent refrigerated storage.

      Science.gov (United States)

      Ye, M; Neetoo, H; Chen, H

      2011-10-01

      Listeria monocytogenes is a major safety concern for ready-to-eat foods. The overall objective of this study was to investigate whether prior frozen storage could enhance the efficacy of edible coatings against L. monocytogenes on cold-smoked salmon during subsequent refrigerated storage. A formulation consisting of sodium lactate (SL, 1·2-2·4%) and sodium diacetate (SD, 0·125-0·25%) or 2·5% Opti.Form (a commercial formulation of SL and SD) was incorporated into each of five edible coatings: alginate, κ-carrageenan, pectin, gelatin and starch. The coatings were applied onto the surface of cold-smoked salmon slices inoculated with L. monocytogenes at a level of 500 CFU cm⁻². In the first phase, the slices were first frozen at -18°C for 6 days and stored at 22°C for 6 days. Alginate, gelatin and starch appeared to be the most effective carriers. In the second phase, cold-smoked salmon slices were inoculated with L. monocytogenes, coated with alginate, gelatin or starch with or without the antimicrobials and stored frozen at -18°C for 12 months. Every 2 months, samples were removed from the freezer and kept at 4°C for 30 days. Prior frozen storage at -18°C substantially enhanced the antilisterial efficacy of the edible coatings with or without antimicrobials during the subsequent refrigerated storage. Plain coatings with ≥ 2 months frozen storage and antimicrobial edible coatings represent an effective intervention to inhibit the growth of L. monocytogenes on cold-smoked salmon. This study demonstrates the effectiveness of the conjunct application of frozen storage and edible coatings to control the growth of L. monocytogenes to enhance the microbiological safety of cold-smoked salmon. © 2011 The Authors. Journal of Applied Microbiology © 2011 The Society for Applied Microbiology.

    8. Coating compositions comprising bismuth-alloyed zinc

      DEFF Research Database (Denmark)

      2008-01-01

      The present application discloses (i) a coating composition comprising a particulate zinc-based alloyed material, said material comprising 0.05-0.7% by weight of bismuth (Bi), the D50 of the particulate material being in the range of 2.5-30 µm; (ii) a coated structure comprising a metal structure...... having a first coating of the zinc-containing coating composition applied onto at least a part of the metal structure in a dry film thickness of 5-100 µm; and an outer coating applied onto said zinc-containing coating in a dry film thickness of 30-200 µm; (iii) a particulate zinc-based alloyed material......, wherein the material comprises 0.05-0.7%(w/w) of bismuth (Bi), and wherein the D50 of the particulate material is in the range of 2.5-30 µm; (iv) a composite powder consisting of at least 25%(w/w) of the particulate zinc-based alloyed material, the rest being a particulate material consisting of zinc...

    9. Formulation and evaluation of the use of edible coatings based on gellan chunks of fresh pineapple cut to minimize deterioration of quality attributes and mass loss

      International Nuclear Information System (INIS)

      Saborio Marin, Laura

      2014-01-01

      The result of the use of edible coatings on special based of gellan in various formulations applied on pieces of fresh cut pineapple is evaluated to reduce the degradation of the quality characteristics and mass loss, as a plan to increase the usefulness. The effect of storage time of the fruit before processing (TAP), the application of vacuum pressure and concentration has been studied of the active components (gellan (0,50-1,00%), oil (0,00 -0,20%), glycerol and sorbitol (1,5-2,5%), CaCl 2 (1.0-10,0%)) of the forming solutions of coating. Several parameters are evaluated: the loss of juice, weight and composition of O 2 and CO 2 in the headspace, content of soluble solids (SS), titratable acidity (TA) color, darkening and appearance of pineapple chunks. The effect of forming solutions is measured on the adhesion, uniformity, coverage and determination of the water vapor resistance (RVA) coating and the presence of molds and yeasts during refrigerated storage at 5 degrees Celsius and 80% relative humidity. Another finding was that the loss of juice of the pieces uncoated increased (p≤0,05) as the increase TAP of 1 to 3 weeks, still higher than those of the coated pieces (0,50-0,75% gellan ), which have been minimal, while weight loss has decreased. The application of a vacuum pressure of 0,08 MPa before coating the pieces has favored the juice loss after the first two weeks of storage and reduced weight loss of uncoated pieces along the storage. The formulation comprised of 0,75% gellan, 1,5% glycerol, 0,10% oil and 1,0% of CaCl 2 has been which allows further reduction of juice loss and weight of pineapple chunks stored at 5 degrees Celsius and 80% RH [es

    10. Effectiveness of almond gum trees exudate as a novel edible coating for improving postharvest quality of tomato (Solanum lycopersicum L.) fruits.

      Science.gov (United States)

      Mahfoudhi, Nesrine; Chouaibi, Moncef; Hamdi, Salem

      2014-01-01

      The use of coatings is a technique used to increase postharvest life of the fruit. Almond gum exudate was used, in comparison with gum arabic, at concentrations of 10% as a novel edible coating, to preserve the quality parameters of tomato (Solanumlycopersicum). Fruits were harvested at the mature-green stage of ripening. Results showed that the coatings delayed significantly (p tomato fruits during storage period (20 days). In addition, the difference between gum arabic and almond gum coatings was not significant (p > 0.05) except for pulp color. Therefore, we can suggest the use of almond gum exudate as a novel edible coating extends the shelf-life of tomato fruits on postharvest.

    11. Application of lemon peel essential oil with edible coating agent to prolong shelf life of tofu and strawberry

      Science.gov (United States)

      Rahmawati, Della; Chandra, Mega; Santoso, Stefanus; Puteri, Maria Gunawan

      2017-01-01

      The essential oil of sweet orange, lemon, and key lime peel were analyzed for their antimicrobial activity. The antimicrobial activity of each citrus essential oil with different concentration was assessed using broth macro-dilution against Bacillus sp, Eschericia coli, Rhizopus stolonifer, and Botrytis sp which represented specific spoilage microorganism in tofu and fresh strawberry. Among all the citrus peel essential oils tested, lemon peel essential oil with 0.6% concentration showed significant activity as an antimicrobial agent against Escherichia coli and Bacillus sp. In other hand 1% of lemon peel essential oil is also considered to be the best concentration of inhibiting the Rhizopus Stolonifer and Botrytis sp. Lemon peel essential oil which has the highest antimicrobial activity was combined with two different kind of edible coating agents (cassava starch and sodium alginate) and was applied in both tofu and strawberry to observe whether it had possibility to decrease the degradation rate of tofu and strawberry. The addition of 0.6% and 1% lemon peel essential oil with each of edible coating agents was significantly able to reduce the degradation of tofu and fresh strawberry.

    12. Aplicação de revestimentos comestíveis em pêssego (Prunus persica Use of edible coating in peaches

      Directory of Open Access Journals (Sweden)

      Giselle de Assis Jacometti

      2003-04-01

      +sorbitol coatings had no effect on physiological activity of peaches, measured by respiration rates, total soluble solid content and total titratable acidity during storage. There was no difference among weight loss rates (~1.4 g/100g.day of all treatments. Edible coatings had no influence on flavor acceptance of the peaches but control fruits had higher scores than coated ones on appearance acceptance evaluation because the opacity caused by the coating. There was no difference among treatments in total count of aerobic mesophiles microorganisms and molds and yeasts during storage but for psychotropic microorganisms, coated fruits presented lower counts than control ones. Gelan and gelan+sorbitol based coatings have not extended shelf-life of cold stored peaches due to coating composition that did not reduced the weight loss and physiological metabolism of the fruits.

    13. Multiphase composite coatings: structure and properties

      International Nuclear Information System (INIS)

      Yurov, V M; Guchenko, S A; Platonova, E S; Syzdykova, A Sh; Lysenko, E N

      2015-01-01

      The paper discusses the results of the research into the formation of ion-plasma multiphase coatings. The types of the formed structures are found to be not so diverse, as those formed, for example, in alloy crystallization. The structures observed are basically of globular type and, more rarely, of unclosed dissipative and cellular structures. It is shown that the properties of the coating formed in deposition are largely determined by its surface energy or surface tension. Since the magnitude of the surface tension (surface energy) in most cases is an additive quantity, each of the elements of the coating composition contributes to the total surface energy. In case of simultaneous sputtering of multiphase cathodes, high entropy coatings with an ordered cellular structure and improved mechanical properties are formed. (paper)

    14. Chemical composition and non-volatile components of three wild edible mushrooms collected from northwest Tunisia

      Directory of Open Access Journals (Sweden)

      ibtissem Kacem Jedidi

      2016-04-01

      Full Text Available In Tunisia, many people collect wild edible mushrooms as pickers for their own consumption. The present work aims at contributing to the determination of the chemical composition, non volatile components content (soluble sugars, free amino acids and minerals and trace elements of three popular Tunisian wild edible mushrooms species collected from the northwest of Tunisia (Agaricus campestris, Boletus edulis and Cantharellus cibarius.All investigated mushrooms revealed that these species are rich sources of proteins (123.70 – 374.10 g kg-1 dry weight (DW and carbohydrates (403.3 – 722.40 g kg-1 DW, and low content of fat (28.2 – 39.9 g kg-1 DW; the highest energetic contribution was guaranteed by C. cibarius (1542.71 kJ / 100 g. A. compestris (33.14 mg/g DW showed the highest concentration of essential amino acids. The composition in individual sugars was also determined, mannitol and trehalose being the most abundant sugars. C. cibarius revealed the highest concentrations of carbohydrates (722.4 g kg-1 DW and A. compestris the lowest concentration (403.3 g kg-1 DW. Potassium (K and sodium (Na are the most abundant minerals in analyzed samples (A. compestris showed the highest concentrations of K and Na, 49141.44 and 9263.886 µg/g DW respectively.

    15. Use of gamma-irradiation technology in combination with edible coating to produce shelf-stable foods

      International Nuclear Information System (INIS)

      Ouattara, B.; Sabato, S.F.; Lacroix, M.

      2002-01-01

      This research was undertaken to determine the effectiveness of low-dose gamma-irradiation combined with edible coatings to produce shelf-stable foods. Three types of commercially distributed food products were investigated: precooked shrimps, ready to cook pizzas, and fresh strawberries. Samples were coated with various formulations of protein-based solutions and irradiated at total doses between 0 and 3 kGy. Samples were stored at 4 deg. C and evaluated periodically for microbial growth. Sensorial analysis was also performed using a nine-point hedonic scale to evaluate the organoleptic characteristics (odor, taste and appearance). The results showed significant (p≤0.05) combined effect of gamma-irradiation and coating on microbial growth (APCs and Pseudomonas putida). The shelf-life extension periods ranged from 3 to 10 days for shrimps and from 7 to 20 days for pizzas, compared to uncoated/unirradiated products. No significant (p>0.05) detrimental effect of gamma-irradiation on sensorial characteristics (odor, taste, appearance) was observed. In strawberries, coating with irradiated protein solutions resulted in significant reduction of the percentage of mold contamination

    16. Conservation of minimally processed pineapple using calcium chloride, edible coating and gamma radiation

      International Nuclear Information System (INIS)

      Pilon, Lucimeire

      2007-01-01

      The aim of this study was to obtain a convenience type pineapple subjected to fresh-cut process and calcium chloride, wheat gluten and alginate-base edible coating and irradiation treatments. The fruits were washed, sanitized with Sumaveg (Sodium Dichloro-s-Triazinetrione) in a 200 mg L-1 chlorine-free solution at 7 deg C for 15 minutes, and then manually peeled. The peeled fruits were sliced into 1 cm thick slices, rinsed in 20 mg L-1 chlorine-free solution for 3 minutes and drained for 3 minutes. In the first experiment, the samples were treated with: 1% calcium chloride + vital wheat gluten solution; 1% calcium chloride + 1% alginate solution; and control. In the second experiment, the samples were treated with: 1% calcium chloride + vital wheat gluten solution + 2.3 kGy; 1% calcium chloride + 2.3kGy; irradiation with 2.3kGy; and control. The packing consisted of rigid polyethylene terephthalate (PET) trays with around 250 g of fruit. The irradiation was performed in a Cobalt-60 multipurpose irradiator with 92 kCi activity and dose value of 2.3 kGy h-1. The samples were stored at 5 ± 1 deg C and evaluated every other day for 12 days. In the first experiment pH and titratable acidity values showed slight variations but were similar between the treatments. There was a decrease in ascorbic acid values in all treatments. Browning was noticed in all treatments over the storage period. Although the values between the treatments were similar, the pineapple treated with calcium chloride + gluten showed firmer texture, less liquid loss, and lower values of polyphenoloxidase and peroxidase activities and CO 2 and ethylene production. Mesophiles and mold and yeast counts were also reduced. No Salmonella and E. coli were detected. Total coliform counts were low in all the treatments and appeared in just a few isolated samples during the storage period. Sensory analyses showed that the samples treated with calcium chloride + gluten had the lower scores for texture

    17. Integration of antimicrobial pectin-based edible coating and active modified atmosphere packaging to preserve the quality and microbial safety of fresh-cut persimmon (Diospyros kaki Thunb. cv. Rojo Brillante).

      Science.gov (United States)

      Sanchís, Elena; Ghidelli, Christian; Sheth, Chirag C; Mateos, Milagros; Palou, Lluís; Pérez-Gago, María B

      2017-01-01

      The greatest hurdle to the commercial marketing of fresh-cut fruits is related to their higher susceptibility to enzymatic browning, tissue softening, and microbial growth. The aim of this study was to test the efficacy of a pectin-based edible coating and low oxygen modified atmosphere packaging (MAP) to control enzymatic browning and reduce microbial growth of fresh-cut 'Rojo Brillante' persimmon. The survival of Escherichia coli, Salmonella enteritidis and Listeria monocytogenes artificially inoculated on fresh-cut fruit was also assessed. The pectin coating was amended with 500 IU mL -1 nisin (NI) as antimicrobial agent and 10 g kg -1 citric acid and 10 g kg -1 calcium chloride as anti-browning and firming agents, respectively. Persimmon slices were dipped in the coating or in water (control) and packed under 5 kPa O 2 (MAP) or in ambient atmosphere for up to 9 days at 5 °C. Microbial growth, package gas composition, colour, firmness, polyphenol oxidase activity, visual quality and overall sensory flavour of persimmon slices were measured during storage. Coating application combined with active MAP significantly reduced the CO 2 emission and O 2 consumption in the package. The coating was effective in reducing browning and also inhibited the growth of mesophilic aerobic bacteria. Coating also reduced the populations of E. coli, S. enteritidis and L. monocytogenes. The combination of the pectin-based edible coating and active MAP proved to be the most effective treatment to maintain the sensory and microbiological quality of persimmon slices for more than 9 days of storage. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

    18. Preparation and characterization of semi-refined kappa carrageenan-based edible film for nano coating application on minimally processed food

      Science.gov (United States)

      Manuhara, Godras Jati; Praseptiangga, Danar; Muhammad, Dimas Rahadian Aji; Maimuni, Bawani Hindami

      2016-02-01

      Shorter and easier processing of semi-refined kappa carrageenan extracted from Euchema cottonii red seaweed result in cheaper price of the polysaccharide. In this study, edible film was prepared from the semi-refined carrageenan without any salt addition. The effect of the carrageenan concentration (1.0, 1.5, and 2.0% w/v) on physical and mechanical properties of the edible film was studied. Edible film thickness and tensile strength increased but elongation at break and water vapor transmission rate (WVTR) decreased as the concentration increased. Based on the characteristic of the edible film, formulation using 2% carrageenan was recommended. The edible film demonstrated the characteristic as follow: 0.054 mm thickness, 21.14 MPa tensile strength, 12.36% elongation at break, and 9.56 g/m2.hour WVTR. It was also noted the carrageenan-based edible film indicated potential physical and mechanical characteristics for nano coating applications on minimally processed food.

    19. Anti-browning and barrier properties of edible coatings prepared with electrospraying

      NARCIS (Netherlands)

      Khan, M.K.I.; Cakmak, I.; Tavman, S.; Schutyser, M.A.I.; Schroen, C.G.P.H.

      2014-01-01

      Electrospraying is a novel technique for the application of coating to foods. In this study, thin lipid-based coatings were prepared by electrospraying on model surface and evaluated for their moisture barrier functionality. Sunflower oil and chocolate based coating materials were electrosprayed at

    20. Modeling and analysis of film composition on mechanical properties of maize starch based edible films.

      Science.gov (United States)

      Prakash Maran, J; Sivakumar, V; Thirugnanasambandham, K; Kandasamy, S

      2013-11-01

      The present study investigates the influence of composition (content of maize starch (1-3 g), sorbitol (0.5-1.0 ml), agar (0.5-1.0 g) and tween-80 (0.1-0.5 ml)) on the mechanical properties (tensile strength, elongation, Young's modulus, puncture force and puncture deformation) of the maize starch based edible films using four factors with three level Box-Behnken design. The edible films were obtained by casting method. The results showed that, tween-80 increases the permeation of sorbitol in to the polymer matrix. Increasing concentration of sorbitol (hydrophilic nature and plasticizing effect of sorbitol) decreases the tensile strength, Young's modulus and puncture force of the films. The results were analyzed by Pareto analysis of variance (ANOVA) and second order polynomial models were obtained for all responses with high R(2) values (R(2)>0.95). 3D response surface plots were constructed to study the relationship between process variables and the responses. Copyright © 2013 Elsevier B.V. All rights reserved.

    1. An iodine supplementation of tomato fruits coated with an edible film of the iodide-doped chitosan.

      Science.gov (United States)

      Limchoowong, Nunticha; Sricharoen, Phitchan; Techawongstien, Suchila; Chanthai, Saksit

      2016-06-01

      In general, the risk of numerous thyroid cancers inevitably increases among people with iodine deficiencies. An iodide-doped chitosan (CT-I) solution was prepared for dipping tomatoes to coat the fresh surface with an edible film (1.5 μm), thereby providing iodine-rich fruits for daily intake. Characterisation of the thin film was conducted by FTIR and SEM. Stability of the CT-I film was studied via water immersion at various time intervals, and no residual iodide leached out due to intrinsic interactions between the cationic amino group of chitosan and iodide ions. Moreover, the iodide supplement exhibited no effect on the antioxidant activity of tomatoes. The iodine content in the film-coated tomato was determined by ICP-OES. The tomato coating with 1.5% (w/v) CT-I contained approximately 0.4 μg iodide per gram fresh weight. In addition, the freshness and storability of iodine-doped tomatoes were also maintained for shelf-life concerns. Copyright © 2016 Elsevier Ltd. All rights reserved.

    2. Compositional changes in (iso)flavonoids and estrogenic activity of three edible Lupinus species by germination and Rhizopus-elicitation

      NARCIS (Netherlands)

      Aisyah, Siti; Vincken, Jean Paul; Andini, Silvia; Mardiah, Zahara; Gruppen, Harry

      2016-01-01

      The effects of germination and elicitation on (iso)flavonoid composition of extracts from three edible lupine species (Lupinus luteus, Lupinus albus, Lupinus angustifolius) were determined by RP-UHPLC-MS. n The total (iso)flavonoid content of lupine increased over 10-fold upon

    3. Effectiveness of edible coatings combined with mild heat shocks on microbial spoilage and sensory quality of fresh cut broccoli (Brassica oleracea L.).

      Science.gov (United States)

      Moreira, María del R; Ponce, Alejandra; Ansorena, R; Roura, Sara I

      2011-08-01

      The use of edible coatings and mild heat shocks is proposed as postharvest treatments to prevent microbial deterioration of refrigerated broccoli. Minimally processed broccoli was coated with either chitosan or carboxymethyl-cellulose (CMC) combined or not with a previous application of a mild heat shock. The evolution of microbial populations (mesophilic, psycrotrophic, Enterobacteriaceae, molds and yeast, and lactic acid bacteria) was studied during 20 d of storage and fitted to Gompertz and logistic models. Results revealed that, at the end of the storage, chitosan coating significantly reduced all microbiological population counts, except lactic acid bacteria; while higher reduction was observed with chitosan coating combined with a heat shock treatment. A significant delay at the beginning of the exponential phase was observed for all the bacterial populations analyzed. On the other hand, CMC coating, with and without a previous thermal treatment, did not exert any antibacterial effect. Excellent agreement was found between experimental microbial counts and predicted values obtained from Gompertz and logistic models. Kinetic modeling was found to be valuable for prediction of microbiological shelf life of broccoli during storage. Results showed that the application of chitosan coating effectively maintained microbiological quality and extended shelf life of minimally processed broccoli. According to these results, the use of the edible chitosan coating alone or in combination with a heat mild shock appear to be a viable alternative for controlling microbiological growth and sensory attributes in minimally processed broccoli. The continuous consumer interest in high quality and food safety, combined with environmental concern has induced to the development and study of edible coatings that avoid the use of synthetic materials. The edible coatings, formed from generally recognized as safe materials, have the potential to reduce weight loss, respiration rate, and

    4. Comparison of Free Total Amino Acid Compositions and Their Functional Classifications in 13 Wild Edible Mushrooms

      Directory of Open Access Journals (Sweden)

      Liping Sun

      2017-02-01

      Full Text Available Thirteen popular wild edible mushroom species in Yunnan Province, Boletus bicolor, Boletus speciosus, Boletus sinicus, Boletus craspedius, Boletus griseus, Boletus ornatipes, Xerocomus, Suillus placidus, Boletinus pinetorus, Tricholoma terreum, Tricholomopsis lividipileata, Termitomyces microcarpus, and Amanita hemibapha, were analyzed for their free amino acid compositions by online pre-column derivazation reversed phase high-performance liquid chromatography (RP-HPLC analysis. Twenty free amino acids, aspartic acid, glutamic acid, serine, glycine, alanine, praline, cysteine, valine, methionine, phenylalanine, isoleucine, leucine, lysine, histidine, threonine, asparagines, glutamine, arginine, tyrosine, and tryptophan, were determined. The total free amino acid (TAA contents ranged from 1462.6 mg/100 g in B. craspedius to 13,106.2 mg/100 g in T. microcarpus. The different species showed distinct free amino acid profiles. The ratio of total essential amino acids (EAA to TAA was 0.13–0.41. All of the analyzed species showed high contents of hydrophobic amino acids, at 33%–54% of TAA. Alanine, cysteine, glutamine, and glutamic acid were among the most abundant amino acids present in all species. The results showed that the analyzed mushrooms possessed significant free amino acid contents, which may be important compounds contributing to the typical mushroom taste, nutritional value, and potent antioxidant properties of these wild edible mushrooms. Furthermore, the principal component analysis (PCA showed that the accumulative variance contribution rate of the first four principal components reached 94.39%. Cluster analysis revealed EAA composition and content might be an important parameter to separate the mushroom species, and T. microcarpus and A. hemibapha showed remarkable EAA content among the 13 species.

    5. Electrodeposition and properties of Zn-Ni-CNT composite coatings

      International Nuclear Information System (INIS)

      Praveen, B.M.; Venkatesha, T.V.

      2009-01-01

      Zn-Ni-CNT composite coatings were prepared by electrodeposition from a sulphate bath. The effect of CNTs on the corrosion behavior, wear resistance and hardness of the composite coatings was investigated. Their corrosion properties were evaluated by polarization, impedance, weight loss and salt spray tests. The CNT particles inclusion improved the corrosion resistance, hardness and wear resistance of the coating. The grain size of the composite coating was smaller than that of a pure Zn-Ni coating with the same Zn/Ni ratio. Scanning electron microscope images and X-ray diffraction patterns of coating revealed its fine-grain nature.

    6. Effect of edible coatings with essential oils on the quality of red raspberries over shelf-life.

      Science.gov (United States)

      Gomes, Marcos de Souza; Cardoso, Maria das Graças; Guimarães, Ana Clara Garcia; Guerreiro, Adriana Cavaco; Gago, Custódia Maria Luís; Vilas Boas, Eduardo Valério de Barros; Dias, Cristina Maria Barrocas; Manhita, Ana Cristina Cabaça; Faleiro, Maria Leonor; Miguel, Maria Graça Costa; Antunes, Maria Dulce Carlos

      2017-02-01

      The objective of the present work was to develop strategies for increasing the shelf-life of red raspberries (Rubus idaeus L.), by preventing microorganism growth. Fruits coated with alginate plus lemon essential oil (0.2%) or orange essential oil (0.1%) after 15 days of storage had less red skin than the remaining samples. The less red color verified in these samples was also coincident with the lower concentration of anthocyanins at the end of the experiment as well as the lower capacity for scavenging ABTS free radicals or quenching singlet oxygen. Cyanidin and pelargonidin glucosides were found in raspberries fruits. The edible coatings supplemented with the essential oil of orange either at 0.1% or 0.2% were very efficient for controlling yeast and mold growth after 15 days of storage. To control the development of aerobic mesophilic bacteria the use of essential oil of lemon 0.2% and essential oil of orange 0.1% were the most efficient. The application of the film improved post-harvest quality of raspberry, since the addition of essential oils of citrus films promoted to the inhibitory effect of fungi and bacteria growth after 15 days of storage, without changing quality parameters. © 2016 Society of Chemical Industry. © 2016 Society of Chemical Industry.

    7. Automatic 1H-NMR Screening of Fatty Acid Composition in Edible Oils

      Directory of Open Access Journals (Sweden)

      David Castejón

      2016-02-01

      Full Text Available In this work, we introduce an NMR-based screening method for the fatty acid composition analysis of edible oils. We describe the evaluation and optimization needed for the automated analysis of vegetable oils by low-field NMR to obtain the fatty acid composition (FAC. To achieve this, two scripts, which automatically analyze and interpret the spectral data, were developed. The objective of this work was to drive forward the automated analysis of the FAC by NMR. Due to the fact that this protocol can be carried out at low field and that the complete process from sample preparation to printing the report only takes about 3 min, this approach is promising to become a fundamental technique for high-throughput screening. To demonstrate the applicability of this method, the fatty acid composition of extra virgin olive oils from various Spanish olive varieties (arbequina, cornicabra, hojiblanca, manzanilla, and picual was determined by 1H-NMR spectroscopy according to this protocol.

    8. Characterization of edible films of Swartzia burchelli phosphated starches and development of coatings for post-harvest application to cherry tomatoes

      Directory of Open Access Journals (Sweden)

      Millene Aparecida Gomes

      2016-08-01

      tomatoes was observed for fruits with edible coatings of greater permeability to water vapor; such fruits exhibited only a slight decline in firmness during storage compared with the control. It can be concluded that the modification performed on the starch and the glycerol concentration positively influenced the properties of the edible films, allowing for optimal use in post-harvest applications. Similarly, the edible coatings conferred better appearance to the fruits, maintaining their maturation index and firmness during the experimental period and providing better post-harvest storage conditions for the cherry tomatoes.

    9. Coating compositions hardenable by ionization beams

      International Nuclear Information System (INIS)

      Chaudhari, D.; Haering, E.; Dobbelstein, A.; Hoselmann, W.

      1976-01-01

      Coating compositions hardenable by ionizing radiation are described which contain as binding agents a mixture of at least 1 unsaturated olefin compound containing urethane groups, and at least 1 further unsaturated olefin compound that may be copolymerized. The unsaturated olefin compound containing the urethane groups is a reaction product of a compound containing carboxylic acid groups and a compound containing at least 1 isocyanate group where the mixture of the two olefins may contain conventional additives of the lacquer industry. 6 claims, no drawings

    10. Physicochemical properties and composition of lipid fraction of selected edible nuts

      International Nuclear Information System (INIS)

      Derewiaka, D.; Szwed, E.; Wolosiak, R.

      2014-01-01

      The study presents the characteristics of oil fraction of 8 types of edible nuts available on the Polish market. All tested nuts were characterized with high content of dry matter. Fatty acid and sterol composition was analyzed by GC-MS. Squalene and tocopherol profiles were examined by HPLC with diode array (DAD) and fluorescence detectors (FLDs). The highest level of fat was found in macadamia (75.4 g/100 g) and the lowest in cashew nuts (46.9 g/100 g). Fatty analysis showed that nuts were rich in unsaturated fatty acids. Monounsaturated fatty acids were predominant in most cases, with the exception of Brazilian nuts, walnuts and pine nuts which were richer in polyunsaturated fatty acids. Sitosterol was the main sterol of nuts, and its content ranged from 96.9 mg/100 g of oil (in macadamia) to 474.8 mg/100 g of oil (in pistachio). Tocopherol homologue was predominant among its fraction with the largest content determined in pistachio (8.3 mg/100 g of oil) and walnuts (8.6 mg/100 g of oil). The presence of squalene was confirmed in seven types of nuts, and the richest source of it were Brazilian nuts (145.8 mg/100 g of oil). The study proofs the variation of nut oil composition, especially phytosterol and tocopherol content and can be used for better characterization of nuts derived from different geographic areas or cultivars. (author)

    11. Physicochemical properties and composition of lipid fraction of selected edible nuts

      Energy Technology Data Exchange (ETDEWEB)

      Derewiaka, D.; Szwed, E.; Wolosiak, R. [Warsaw Univ. of Life Sciences, Warsaw (Poland). Dept. of Biotechnology

      2014-01-15

      The study presents the characteristics of oil fraction of 8 types of edible nuts available on the Polish market. All tested nuts were characterized with high content of dry matter. Fatty acid and sterol composition was analyzed by GC-MS. Squalene and tocopherol profiles were examined by HPLC with diode array (DAD) and fluorescence detectors (FLDs). The highest level of fat was found in macadamia (75.4 g/100 g) and the lowest in cashew nuts (46.9 g/100 g). Fatty analysis showed that nuts were rich in unsaturated fatty acids. Monounsaturated fatty acids were predominant in most cases, with the exception of Brazilian nuts, walnuts and pine nuts which were richer in polyunsaturated fatty acids. Sitosterol was the main sterol of nuts, and its content ranged from 96.9 mg/100 g of oil (in macadamia) to 474.8 mg/100 g of oil (in pistachio). Tocopherol homologue was predominant among its fraction with the largest content determined in pistachio (8.3 mg/100 g of oil) and walnuts (8.6 mg/100 g of oil). The presence of squalene was confirmed in seven types of nuts, and the richest source of it were Brazilian nuts (145.8 mg/100 g of oil). The study proofs the variation of nut oil composition, especially phytosterol and tocopherol content and can be used for better characterization of nuts derived from different geographic areas or cultivars. (author)

    12. Method and compositions for producting optically clear photocatalytic coatings

      DEFF Research Database (Denmark)

      2009-01-01

      The invention relates to a method and compositions for producing a hydrophilic coating on a surface of a solid material. The method comprises a cleaning step and a coating step. The cleaning step may be preceded by an initial cleaning step and it may optionally be succeeded by a preconditioning...... step prior to the coating step. The cleaning step comprises cleaning and preconditioning a surface of a material by use of a first cleaning fluid composition comprising ceria (CeO2) particles. The coating step comprises treatment by use of a coating fluid composition comprising photocatalytically...

    13. Coating composition curable by electron beam irradiation

      International Nuclear Information System (INIS)

      Masuda, Hiromasa; Iijima, Ken-ichi.

      1971-01-01

      Here is provided a coating composition curable with low dose of electron beams to give a smooth coating film having no surface tackiness. In one example, 126 parts of melamine was reacted with 682 parts of formalin followed by 697 parts of β-hydroxyethyl acrylate to produce component (A) (viscosity 780 cp). On the other hand, 900 parts of tung oil was reacted with 343 parts of maleic anhydride followed by 22 parts of dimethylaminoethyl methacrylate and 406 parts of β-hydroxyethyl acrylate. The resulting product was diluted with 508 parts of methyl methacrylate to give component (B) (dark red, viscous substance). 900 parts of (A), 100 parts of (B), 0.5 part of bees wax and 0.2 part of paraffin wax were blended together. A sized material was coated with the mixture and irradiated with electron beams (6 Mrad) in the presence of air. A smooth film free from surface tackiness was obtained. β-hydroxyethyl acrylate may be replaced by other hydroxyalkyl esters of α,β-unsaturated acids, and melamine may be replaced by urea, benzoguanamine or acetoguanamine. Tung oil may be replaced by linseed, safflower, soybean, rice, oiticica or cotton seed oil. A more flexible film is obtained by using component (B) in a larger proportion. (A)/(B) ratio should be in the range of 90/10 to 10/90 by wt. (Kaichi, S.)

    14. The Behaviour of Some Vegetable-Based Materials Used as Edible Coating on Chicken Nuggets

      Directory of Open Access Journals (Sweden)

      Osman Kılınççeker

      2011-01-01

      Full Text Available In this study, chicken nuggets were predusted with zein or soy protein isolate (SPI as the first coating. Next they were coated with 0.1, 0.2 or 0.3 % carboxymethylcellulose (CMC batters as the second coating, and then breaded with bread crumbs. Finally, they were fried at 190 °C for 2, 4 or 6 min. Predusting materials were found to enhance some physical, chemical and sensorial properties of nuggets after frying. In particular, using SPI was more advantageous than zein. It increased penetrometer values and sensorial scores as it decreased moisture loss. The performance values of batter materials were improved compared to the control. Also, the yield, moisture rate, penetrometer and general appearance values decreased as the frying time increased. During this period, frying loss and fat absorption increased. Results showed that the best coating process was using SPI as predusting material, 0.1 % CMC for batter, and 2 to 4 min of frying time.

    15. Nutritional Composition and Antioxidant Capacity in Edible Flowers: Characterisation of Phenolic Compounds by HPLC-DAD-ESI/MSn

      Directory of Open Access Journals (Sweden)

      Inmaculada Navarro-González

      2014-12-01

      Full Text Available Edible flowers are commonly used in human nutrition and their consumption has increased in recent years. The aim of this study was to ascertain the nutritional composition and the content and profile of phenolic compounds of three edible flowers, monks cress (Tropaeolum majus, marigold (Tagetes erecta and paracress (Spilanthes oleracea, and to determine the relationship between the presence of phenolic compounds and the antioxidant capacity. Proximate composition, total dietary fibre (TDF and minerals were analysed according to official methods: total phenolic compounds (TPC were determined with Folin-Ciocalteu’s reagent, whereas antioxidant capacity was evaluated using Trolox Equivalent Antioxidant Capacity (TEAC and Oxygen Radical Absorbance Capacity (ORAC assays. In addition, phenolic compounds were characterised by HPLC-DAD-MSn. In relation to the nutritional value, the edible flowers had a composition similar to that of other plant foods, with a high water and TDF content, low protein content and very low proportion of total fat—showing significant differences among samples. The levels of TPC compounds and the antioxidant capacity were significantly higher in T. erecta, followed by S. oleracea and T. majus. Thirty-nine different phenolic compounds were tentatively identified, with flavonols being the major compounds detected in all samples, followed by anthocyanins and hydroxycynnamic acid derivatives. In T. erecta small proportions of gallotannin and ellagic acid were also identified.

    16. Comparative study on free amino acid composition of wild edible mushroom species.

      Science.gov (United States)

      Ribeiro, Bárbara; Andrade, Paula B; Silva, Branca M; Baptista, Paula; Seabra, Rosa M; Valentão, Patrícia

      2008-11-26

      A comparative study on the amino acid composition of 11 wild edible mushroom species (Suillus bellini, Suillus luteus, Suillus granulatus, Tricholomopsis rutilans, Hygrophorus agathosmus, Amanita rubescens, Russula cyanoxantha, Boletus edulis, Tricholoma equestre, Fistulina hepatica, and Cantharellus cibarius) was developed. To define the qualitative and quantitative profiles, a derivatization procedure with dabsyl chloride was performed, followed by HPLC-UV-vis analysis. Twenty free amino acids (aspartic acid, glutamic acid, asparagine, glutamine, serine, threonine, glycine, alanine, valine, proline, arginine, isoleucine, leucine, tryptophan, phenylalanine, cysteine, ornithine, lysine, histidine, and tyrosine) were determined. B. edulis and T. equestre were revealed to be the most nutritional species, whereas F. hepatica was the poorest. The different species exhibited distinct free amino acid profiles. The quantification of the identified compounds indicated that, in a general way, alanine was the major amino acid. The results show that the analyzed mushroom species possess moderate amino acid contents, which may be relevant from a nutritional point of view because these compounds are indispensable for human health. A combination of different mushroom species in the diet would offer good amounts of amino acids and a great diversity of palatable sensations.

    17. Chemical composition and antimicrobial activity of the essential oil from the edible aromatic plant Aristolochia delavayi.

      Science.gov (United States)

      Li, Zhi-Jian; Njateng, Guy S S; He, Wen-Jia; Zhang, Hong-Xia; Gu, Jian-Long; Chen, Shan-Na; Du, Zhi-Zhi

      2013-11-01

      The essential oil obtained by hydrodistillation from the aerial parts of Aristolochia delavayi Franch. (Aristolochiaceae), a unique edible aromatic plant consumed by the Nakhi (Naxi) people in Yunnan, China, was investigated using GC/MS analysis. In total, 95 components, representing more than 95% of the oil composition, were identified, and the main constituents found were (E)-dec-2-enal (52.0%), (E)-dodec-2-enal (6.8%), dodecanal (3.35%), heptanal (2.88%), and decanal (2.63%). The essential oil showed strong inhibitory activity (96% reduction) of the production of bacterial volatile sulfide compounds (VSC) by Klebsiella pneumoniae, an effect that was comparable with that of the reference compound citral (91% reduction). Moreover, the antimicrobial activity of the essential oil and the isolated major compound against eight bacterial and six fungal strains were evaluated. The essential oil showed significant antibacterial activity against Providencia stuartii and Escherichia coli, with minimal inhibitory concentrations (MIC) ranging from 3.9 to 62.5 μg/ml. The oil also showed strong inhibitory activity against the fungal strains Trichophyton ajelloi, Trichophyton terrestre, Candida glabrata, Candida guilliermondii, and Cryptococcus neoformans, with MIC values ranging from 3.9 to 31.25 μg/ml, while (E)-dec-2-enal presented a lower antifungal activity than the essential oil. Copyright © 2013 Verlag Helvetica Chimica Acta AG, Zürich.

    18. Effect of Presence and Concentration of Plasticizers, Vegetable Oils, and Surfactants on the Properties of Sodium-Alginate-Based Edible Coatings

      Directory of Open Access Journals (Sweden)

      Tugce Senturk Parreidt

      2018-03-01

      Full Text Available Achieving high quality of a coated food product is mostly dependent on the characteristics of the food material to be coated, the properties of the components in the coating solution, and the obtained coating material. In the present study, usability and effectiveness of various components as well as their concentrations were assessed to produce an effective coating material. For this purpose, different concentrations of gelling agent (sodium alginate 0–3.5%, w/w, plasticizers (glycerol and sorbitol (0–20%, w/w, surfactants (tween 40, tween 80, span 60, span 80, lecithin (0–5%, w/w, and vegetable oils (sunflower oil, olive oil, rapeseed oil (0–5%, w/w were used to prepare edible coating solutions. Formulations were built gradually, and characteristics of coatings were evaluated by analyzing surface tension values and its polar and dispersive components, emulsion droplet size, and optical appearance in microscopic scale. The results obtained showed that 1.25% sodium alginate, 2% glycerol, 0.2% sunflower oil, 1% span 80, and 0.2% tween 40 or tween 80 can be used in formulation to obtain an effective coating for hydrophobic food surfaces. Three formulations were designed, and their stability (emulsion droplet size, optical characteristics, and creaming index and wettability tests on strawberry showed that they could be successfully used in coating applications.

    19. Effect of Presence and Concentration of Plasticizers, Vegetable Oils, and Surfactants on the Properties of Sodium-Alginate-Based Edible Coatings

      Science.gov (United States)

      Schott, Michael; Müller, Kajetan

      2018-01-01

      Achieving high quality of a coated food product is mostly dependent on the characteristics of the food material to be coated, the properties of the components in the coating solution, and the obtained coating material. In the present study, usability and effectiveness of various components as well as their concentrations were assessed to produce an effective coating material. For this purpose, different concentrations of gelling agent (sodium alginate 0–3.5%, w/w), plasticizers (glycerol and sorbitol (0–20%, w/w), surfactants (tween 40, tween 80, span 60, span 80, lecithin (0–5%, w/w), and vegetable oils (sunflower oil, olive oil, rapeseed oil (0–5%, w/w) were used to prepare edible coating solutions. Formulations were built gradually, and characteristics of coatings were evaluated by analyzing surface tension values and its polar and dispersive components, emulsion droplet size, and optical appearance in microscopic scale. The results obtained showed that 1.25% sodium alginate, 2% glycerol, 0.2% sunflower oil, 1% span 80, and 0.2% tween 40 or tween 80 can be used in formulation to obtain an effective coating for hydrophobic food surfaces. Three formulations were designed, and their stability (emulsion droplet size, optical characteristics, and creaming index) and wettability tests on strawberry showed that they could be successfully used in coating applications. PMID:29509669

    20. Suspension plasma sprayed composite coating using amorphous powder feedstock

      International Nuclear Information System (INIS)

      Chen Dianying; Jordan, Eric H.; Gell, Maurice

      2009-01-01

      Al 2 O 3 -ZrO 2 composite coatings were deposited by the suspension plasma spray process using molecularly mixed amorphous powders. X-ray diffraction (XRD) analysis shows that the as-sprayed coating is composed of α-Al 2 O 3 and tetragonal ZrO 2 phases with grain sizes of 26 nm and 18 nm, respectively. The as-sprayed coating has 93% density with a hardness of 9.9 GPa. Heat treatment of the as-sprayed coating reveals that the Al 2 O 3 and ZrO 2 phases are homogeneously distributed in the composite coating

    1. Durable polymer-aerogel based superhydrophobic coatings, a composite material

      Science.gov (United States)

      Kissel, David J; Brinker, Charles Jeffrey

      2014-03-04

      Provided are polymer-aerogel composite coatings, devices and articles including polymer-aerogel composite coatings, and methods for preparing the polymer-aerogel composite. The exemplary article can include a surface, wherein the surface includes at least one region and a polymer-aerogel composite coating disposed over the at least one region, wherein the polymer-aerogel composite coating has a water contact angle of at least about 140.degree. and a contact angle hysteresis of less than about 1.degree.. The polymer-aerogel composite coating can include a polymer and an ultra high water content catalyzed polysilicate aerogel, the polysilicate aerogel including a three dimensional network of silica particles having surface functional groups derivatized with a silylating agent and a plurality of pores.

    2. Durable polymer-aerogel based superhydrophobic coatings: a composite material

      Science.gov (United States)

      Kissel, David J.; Brinker, Charles Jeffrey

      2016-02-02

      Provided are polymer-aerogel composite coatings, devices and articles including polymer-aerogel composite coatings, and methods for preparing the polymer-aerogel composite. The exemplary article can include a surface, wherein the surface includes at least one region and a polymer-aerogel composite coating disposed over the at least one region, wherein the polymer-aerogel composite coating has a water contact angle of at least about 140.degree. and a contact angle hysteresis of less than about 1.degree.. The polymer-aerogel composite coating can include a polymer and an ultra high water content catalyzed polysilicate aerogel, the polysilicate aerogel including a three dimensional network of silica particles having surface functional groups derivatized with a silylating agent and a plurality of pores.

    3. Nutritional composition of different grades of edible bird's nest and its enzymatic hydrolysis

      Science.gov (United States)

      Noor, Hidayati Syamimi Mohd; Babji, Abdul Salam; Lim, Seng Joe

      2018-04-01

      Edible bird nest (EBN) is a powerful and nutritious food usually consumed by the Chinese Community and it is considered among the most expensive animal products which are made up by salivation of swiftlets (Aerodramus fuciphagus). The other 5% to 10% are made up of foreign matters such as feathers, faecal matter and dirt. The EBN is graded based on its aesthetics as well as its cleaning processes. The aim of this study were to determine and compare EBN of different grades (A, B, C, D) in terms of proximate composition and amino acid profile, and next to enzymatically hydrolyse and determine the degree of hydrolysis (DH) and the recovery percentage of EBN hydrolysates. The enzymatic hydrolysis were performed as an alternative cleaning process of the various grades of EBN, where the glycoproteins were hydrolysed to glycopeptides, making them soluble and leaving behind other insoluble impurities. The results in this study showed that EBN contained high crude protein content: 60.59% (EBNA), 59.50% (EBNB), 54.29% (EBNC) and 56.57% (EBND). Lower grade EBNs (EBNC and EBND) has much higher ash content, i.e. impurities, compared to higher grade EBNs (EBNA and EBNB). In terms of amino acid profile, EBND showed the highest total amino acids compared to EBNA, EBNB and EBNC, with serine and aspartic acid being the main amino acids. Treating the EBN with alcalase for 1.0 - 4.0 hours produced hydrolysates with different degree of hydrolysis (DH), ranging from 10.83 %DH (EBNA) to 13.79 %DH (EBNC). The recovery of EBN after enzymatic hydrolysis range from 89 % (EBNB) to 99% (EBNA). Overall, results showed nutritional composition and amino acid profile of EBN of various grades were significantly different in its nutritional quality, while the enzymatic hydrolysis has successfully separated the impurities from the lower grades EBN.

    4. Analytical Modeling of Hard-Coating Cantilever Composite Plate considering the Material Nonlinearity of Hard Coating

      Directory of Open Access Journals (Sweden)

      Wei Sun

      2015-01-01

      Full Text Available Due to the material nonlinearity of hard coating, the coated structure produces the nonlinear dynamical behaviors of variable stiffness and damping, which make the modeling of hard-coating composite structure become a challenging task. In this study, the polynomial was adopted to characterize this material nonlinearity and an analytical modeling method was developed for the hard-coating composite plate. Firstly, to relate the hard-coating material parameters obtained by test and the analytical model, the expression of equivalent strain of composite plate was derived. Then, the analytical model of hard-coating composite plate was created by energy method considering the material nonlinearity of hard coating. Next, using the Newton-Raphson method to solve the vibration response and resonant frequencies of composite plate and a specific calculation procedure was also proposed. Finally, a cantilever plate coated with MgO + Al2O3 hard coating was chosen as study case; the vibration response and resonant frequencies of composite plate were calculated using the proposed method. The calculation results were compared with the experiment and general linear calculation, and the correctness of the created model was verified. The study shows the proposed method can still maintain an acceptable precision when the material nonlinearity of hard coating is stronger.

    5. Coating compositions hardenable by ionization beams

      International Nuclear Information System (INIS)

      Chaudhari, D.; Haering, E.; Dobbelstein, A.; Hoselmann, W.

      1976-01-01

      Coating compositions hardenable by ionizing radiation comprise as binding agents a mixture of A. at least 1 unsaturated olefin compound containing urethane groups, and B. at least 1 further unsaturated olefin compound that may be copolymerized. The unsaturated olefin compound A. containing the urethane groups in a reaction product of (a) a compound of the general formula (CHR 1 = CR 2 COOCH 2 CH(OH)CH 2 O CO-)/sub n/R where n is 1 or 2, where R stands for a straight chain or branched alkyl group of valence n, where R 1 is hydrogen, methyl; or the group -COOCH 2 CH(OH)CH 2 OCOR 3 - where R 3 is a monovalent alkyl residue and where R 2 is hydrogen or methyl, and (b) a compound containing at least 1 isocyanate group where the mixture of (A) and (B) may contain conventional additives of the lacquer industry. 6 claims

    6. Effect of edible coating ingredients incorporated into predusting mix on moisture content, fat content and consumer acceptability of fried breaded product

      Directory of Open Access Journals (Sweden)

      Nongnuch Raksakulthai

      2008-04-01

      Full Text Available The effect of edible coatings and their concentrations on moisture and fat contents of fried breaded potato were investigated. Hydroxypropyl methylcellulose (HPMC, methylcellulose (MC or wheat gluten (WG were incorporate into predusting mix to achieve coating material concentration of 3-12% (w/w. Blanched potatoes were first coated with predusting mix and followed sequentially by battering, breading and deep frying at 170°C for 3 min. Moisture and fat contents in the core and crust of sample and intact samples were determined. It was found that HPMC and MC could reduce moisture loss and fat absorption than WG. Predusting mix with 6% MC was the most effective to retain moisture and reduce fat absorption. This predusting mix was then applied to commercial breaded shrimps. In both prefried and fried products, treated breaded shrimps had more moisture and less fat than untreated breaded shrimps. They also were lower in product hardness and crust hardness than untreated samples. Sensory evaluation showed that treated and untreated shrimp samples had similar rating for appearance, color, flavor, taste, texture and overall. Treated breaded shrimp was acceptable to the consumers. The application of edible coatings into predusting mix can be easily introduced into the production process and is beneficial to both food industry and consumers.

    7. Utilization of carrageenan, citric acid and cinnamon oil as an edible coating of chicken fillets to prolong its shelf life under refrigeration conditions.

      Science.gov (United States)

      Khare, Anshul Kumar; Abraham, Robinson J J; Appa Rao, V; Babu, R Narendra

      2016-02-01

      The present study was conducted to determine efficacy of edible coating of carrageenan and cinnamon oil to enhance the shelf life of chicken meat stored under refrigeration conditions. Chicken breast was coated with carrageenan and cinnamon oil by three methods of application viz., spraying brushing and dipping. The coated meat was evaluated for drip loss, pH, thiobarbituric acid number (TBA), tyrosine value (TV), extract release volume (ERV), Warner-Bratzler shear force value (WBSFV), instrumental color, microbiological, and sensory qualities as per standard procedures. There was a significant difference observed for physicochemical parameters (pH, TBA, TV, ERV, drip loss and WBSFV) and microbiological analysis between storage periods in all the samples and between the control and treatments throughout the storage period but samples did not differed significantly for hunter color scores. However, there was no significant difference among three methods of application throughout the storage period though dipping had a lower rate of increase. A progressive decline in mean sensory scores was recorded along with the increase in storage time. The carrageenan and cinnamon edible coating was found to be a good alternative to enhance the shelf life of chicken meat under refrigeration conditions. It was also observed from study that dipping method of the application had comparatively higher shelf life than other methods of application.

    8. Cassava starch edible coating incorporated with propolis on bioactive compounds in strawberries

      Directory of Open Access Journals (Sweden)

      Ariela Betsy Thomas

      2016-02-01

      Full Text Available ABSTRACT Strawberry is a fruit appreciated throughout the world due to its attractive quality attributes and stands out due to its high phenolic compound content, which positively contribute to biological properties of nutritional interest. The objective of this study was to evaluate the effect of cassava starch coatings incorporated with propolis combinations on the phytochemical content and the maintenance and increase of the strawberry antioxidant activity. The treatments were 3% cassava starch (CS, 3% cassava starch + 33% ethanolic propolis extract (CS + P33%, 3% cassava starch + 66% ethanolic propolis extract (CS + P66% and control (C. The fruits were stored at 4 °C ± 0.5 ºC and 90%RH for 16 days, making up a completely randomized design with 4 treatments and 5 time evaluations. Vitamin C, phenolic compound, anthocyanin, and antioxidant activity levels were evaluated through two methods. The coating with 66% of propolis promoted higher Vitamin C content than fruits submitted to the other treatments at 8 and 12 days of storage. For antioxidant activity, fruits treated with CS maintained a higher FRS percentage (free radical scavenging at all time evaluations. Control fruits presented higher anthocyanin content at the last evaluation time when the highest antioxidant capacity, by the ABTS method (2,2'-azino-bis(3-ethylbenzothiazoline-6-sulphonic acid, was observed in fruits with CS and CS + P66% treatments. There was an increase tendency of the phenolic content during storage in all evaluated fruits. The propolis concentrations used, however, were not sufficient to increase or maintain the antioxidant capacity and phenolic contents of strawberries.

    9. Analysis of total oil and fatty acids composition by near infrared reflectance spectroscopy in edible nuts

      Science.gov (United States)

      Kandala, Chari V.; Sundaram, Jaya

      2014-10-01

      Near Infrared (NIR) Reflectance spectroscopy has established itself as an important tool in quantifying water and oil present in various food materials. It is rapid and nondestructive, easier to use, and does not require processing the samples with corrosive chemicals that would render them non-edible. Earlier, the samples had to be ground into powder form before making any measurements. With the development of new soft ware packages, NIR techniques could now be used in the analysis of intact grain and nuts. While most of the commercial instruments presently available work well with small grain size materials such as wheat and corn, the method present here is suitable for large kernel size products such as shelled or in-shell peanuts. Absorbance spectra were collected from 400 nm to 2500 nm using a NIR instrument. Average values of total oil contents (TOC) of peanut samples were determined by standard extraction methods, and fatty acids were determined using gas chromatography. Partial least square (PLS) analysis was performed on the calibration set of absorption spectra, and models were developed for prediction of total oil and fatty acids. The best model was selected based on the coefficient of determination (R2), Standard error of prediction (SEP) and residual percent deviation (RPD) values. Peanut samples analyzed showed RPD values greater than 5.0 for both absorbance and reflectance models and thus could be used for quality control and analysis. Ability to rapidly and nondestructively measure the TOC, and analyze the fatty acid composition, will be immensely useful in peanut varietal improvement as well as in the grading process of grain and nuts.

    10. Electrodeposition and Corrosion Resistance of Ni-Graphene Composite Coatings

      Science.gov (United States)

      Szeptycka, Benigna; Gajewska-Midzialek, Anna; Babul, Tomasz

      2016-08-01

      The research on the graphene application for the electrodeposition of nickel composite coatings was conducted. The study assessed an important role of graphene in an increased corrosion resistance of these coatings. Watts-type nickel plating bath with low concentration of nickel ions, organic addition agents, and graphene as dispersed particles were used for deposition of the composite coatings nickel-graphene. The results of investigations of composite coatings nickel-graphene deposited from the bath containing 0.33, 0.5, and 1 g/dm3 graphene and one surface-active substance were shown. The contents of particles in coatings, the surface morphology, the cross-sectional structures of the coated samples, and their thickness and the internal stresses were studied. Voltammetric method was used for examination of the corrosion resistance of samples of composite coatings in 0.5 M NaCl. The obtained results suggest that the content of incorporated graphene particles increases with an increasing amount of graphene in plating bath. The application of organic compounds was advantageous because it caused compressive stresses in the deposited coatings. All of the nickel-graphene composite layers had better corrosion resistance than the nickel coating.

    11. Cold-Sprayed AZ91D Coating and SiC/AZ91D Composite Coatings

      Directory of Open Access Journals (Sweden)

      Yingying Wang

      2018-03-01

      Full Text Available As an emerging coating building technique, cold spraying has many advantages to elaborate Mg alloy workpieces. In this study, AZ91D coatings and AZ91D-based composite coatings were deposited using cold spraying. Coatings were prepared using different gas temperatures to obtain the available main gas temperature. Compressed air was used as the accelerating gas, and although magnesium alloy is oxidation-sensitive, AZ91D coatings with good performance were obtained. The results show that dense coatings can be fabricated until the gas temperature is higher than 500 °C. The deposition efficiency increases greatly with the gas temperature, but it is lower than 10% for all coating specimens. To analyze the effects of compressed air on AZ91D powder particles and the effects of gas temperature on coatings, the phase composition, porosity, cross-sectional microstructure, and microhardness of coatings were characterized. X-ray diffraction and oxygen content analysis clarified that no phase transformation or oxidation occurred on AZ91D powder particles during cold spraying processes with compressed air. The porosity of AZ91D coatings remained between 3.6% and 3.9%. Impact melting was found on deformed AZ91D particles when the gas temperature increased to 550 °C. As-sprayed coatings exhibit much higher microhardness than as-casted bulk magnesium, demonstrating the dense structure of cold-sprayed coatings. To study the effects of ceramic particles on cold-sprayed AZ91D coatings, 15 vol % SiC powder particles were added into the feedstock powder. Lower SiC content in the coating than in the feedstock powder means that the deposition efficiency of the SiC powder particles is lower than the deposition efficiency of AZ91D particles. The addition of SiC particles reduces the porosity and increases the microhardness of cold-sprayed AZ91D coatings. The corrosion behavior of AZ91D coating and SiC reinforced AZ91D composite coating were examined. The Si

    12. Multilayer oxidation resistant coating for SiC coated carbon/carbon composites at high temperature

      International Nuclear Information System (INIS)

      Li Hejun; Jiao Gengsheng; Li Kezhi; Wang Chuang

      2008-01-01

      To prevent carbon/carbon (C/C) composites from oxidation, a multilayer coating based on molybdenum disilicide and titanium disilicide was formed using a two-step pack cementation technique in argon atmosphere. XRD and SEM analysis showed that the internal coating was a bond SiC layer that acts as a buffer layer, and that the external multilayer coating formed in the two-step pack cementation was composed of two MoSi 2 -TiSi 2 -SiC layers. This coating, which is characterized by excellent thermal shock resistance, could effectively protect the composites from exposure to an oxidizing atmosphere at 1773 K for 79 h. The oxidation of the coated C/C composites was primarily due to the reaction of C/C matrix and oxygen diffusing through the penetrable cracks in the coating

    13. Influence of polysaccharide-based edible coatings as carriers of prebiotic fibers on quality attributes of ready-to-eat fresh blueberries.

      Science.gov (United States)

      Alvarez, María V; Ponce, Alejandra G; Moreira, María R

      2018-05-01

      Little information is available regarding the effect of dietary fibers added into edible coatings on quality attributes of ready-to-eat fruits. The aim of this study was to evaluate the effects of sodium alginate (AL) and chitosan (CH) edible coatings enriched with four different dietary fibers (apple fiber, orange fiber, inulin and oligofructose) on microbiological, nutritional, physico-chemical and sensorial properties of ready-to-eat fresh blueberries stored for 18 days at 5 °C. The most encouraging results were found for CH coatings (with and without fibers) which significantly inhibited the growth of mesophilic bacteria and yeasts/molds (reductions up to 1.9 log CFU g -1 ), reduced decay rate by more than 50%, enhanced antioxidant properties, retained fruit firmness, delayed off-odor development and improved overall visual quality of blueberries. Oligofructose and orange fiber added to CH coatings enhanced antioxidant properties of fruits and allowed higher reductions in yeast/mold counts compared to the use of CH alone. CH-based coatings enriched with inulin, oligofructose and apple fiber extended sensory shelf life of blueberries by 6 days. AL coatings (with and without fiber) allowed delaying fungal decay and also retaining antioxidant properties but did not improve the microbiological and sensory quality of fruits. The results proved that fiber-enriched CH treatments allowed the maintenance of freshness and the improvement of the quality of ready-to-eat blueberries. It might be an interesting option to offer consumers a healthy product with prebiotic potential and an extended shelf life. © 2017 Society of Chemical Industry. © 2017 Society of Chemical Industry.

    14. Laser cladding of wear resistant metal matrix composite coatings

      International Nuclear Information System (INIS)

      Yakovlev, A.; Bertrand, Ph.; Smurov, I.

      2004-01-01

      A number of coatings with wear-resistant properties as well as with a low friction coefficient are produced by laser cladding. The structure of these coatings is determined by required performance and realized as metal matrix composite (MMC), where solid lubricant serves as a ductile matrix (e.g. CuSn), reinforced by appropriate ceramic phase (e.g. WC/Co). One of the engineered coating with functionally graded material (FGM) structure has a dry friction coefficient 0.12. Coatings were produced by coaxial injection of powder blend into the zone of laser beam action. Metallographic and tribological examinations were carried out confirming the advanced performance of engineered coatings

    15. Effect of novel bioactive edible coatings based on jujube gum and nettle oil-loaded nanoemulsions on the shelf-life of Beluga sturgeon fillets.

      Science.gov (United States)

      Gharibzahedi, Seyed Mohammad Taghi; Mohammadnabi, Sara

      2017-02-01

      Effect of jujube gum (JG; 4, 8 and 12% wt)-based nanoemulsions (NEs) containing nettle essential oil (NEO; 2, 3.5 and 5% wt) as new edible coatings was investigated to preserve Beluga sturgeon fillets (BSFs) during 15 day-refrigerated storage at 4°C. Physical (weight loss, cooking loss, color and texture), chemical (pH, FFA, PV, TBARS and TVB-N), microbiological (total and psychrotrophic bacterial counts), and sensorial characteristics of BSFs were kinetically analyzed. Preliminary studies showed that the NEs formulated with NEO lower than 5% at all JG concentrations were able to form stable coating solutions owing to the highest short-term stability (>90%) and entrapment efficiency (94.4-98.3%). Edible NE coating formulated with 12% JG and 3.5% NEO as a novel antimicrobial and antioxidant biomaterial exhibited the lowest weight and cooking losses, pH changes, textural and color deterioration, lipid oxidation and microbial growth in BSFs refrigerated over a period of 15days (P<0.05). Copyright © 2016 Elsevier B.V. All rights reserved.

    16. Mechanical behavior of nanocellulose coated jute/green epoxy composites

      Science.gov (United States)

      Jabbar, A.; Militký, J.; Ali, A.; Usman Javed, M.

      2017-10-01

      The present study was aimed to investigate the effect of nanocellulose coating on the mechanical behavior of jute/green epoxy composites. Cellulose was purified from waste jute fibers, converted to nanocellulose by acid hydrolysis and subsequently 3, 5 and 10 wt % of nanocellulose suspensions were coated over woven jute reinforcement. The composites were prepared by hand layup and compression molding technique. The surface topologies of treated jute fibers, jute cellulose nanofibrils (CNF), nanocellulose coated jute fabrics and fractured surfaces of composites were characterized by scanning electron microscopy (SEM). The prepared composites were evaluated for tensile, flexural, fatigue and fracture toughness properties. The results revealed the improvement in tensile modulus, flexural strength, flexural modulus, fatigue life and fracture toughness of composites with the increase in concentration of nanocellulose coating over jute reinforcement except the decrease in tensile strength.

    17. Essential oils as a natural additive in the edible films and coatings (active packaging system): A Review

      OpenAIRE

      R Fattahi; A Bahrami

      2018-01-01

      Background: Common plastics used in food packaging have a lot of environmental problems. The aim of this study, was to review the latest research results on edible and biodegradable packaging and the positive effect of essential oil in them. Methods: In order to gather information, articles containing one of the words in their text, including: Food packaging, Edible film, Essential oils and Biodegradable film were searched between 1993 and 2017 in Science direct, Elsevier, Springer, Americ...

    18. Process engineering of ceramic composite coatings for fuel cell systems

      Energy Technology Data Exchange (ETDEWEB)

      Li, G.; Kim, H.; Chen, M.; Yang, Q.; Troczynski, T. [British Columbia Univ., Vancouver, BC (Canada). Dept. of Metals and Materials Engineering

      2003-07-01

      Researchers at UBCeram at the Department of Metals and Materials Engineering at the University of British Columbia have developed a technology to chemically bond composite sol-gel (CB-CSG) coating onto metallic surfaces of complex or concave shapes. The process has been optimized for electrically resistive coatings and corrosion-resistant coatings. The CSG is sprayed onto metallic surfaces and is heat-treated at 300 degrees C to partially dehydrate the hydroxides. The CSG film is then chemically bonded through reaction of active alumina with metal phosphates, such as aluminium phosphate. A new chromate-free process is being developed to address the issue of coatings porosity. The electrodeposition technique involves polymer particles mixed with suspended fine alumina particles which are co-deposited by electrophoretic means or by electrocoagulation. The composite e-coatings have excellent mechanical properties and are being considered as a protective coating for various components of fuel cell systems. 9 refs., 7 figs.

    19. Antifungal activity of food additives in vitro and as ingredients of hydroxypropyl methylcellulose-lipid edible coatings against Botrytis cinerea and Alternaria alternata on cherry tomato fruit.

      Science.gov (United States)

      Fagundes, Cristiane; Pérez-Gago, María B; Monteiro, Alcilene R; Palou, Lluís

      2013-09-16

      The antifungal activity of food additives or 'generally recognized as safe' (GRAS) compounds was tested in vitro against Botrytis cinerea and Alternaria alternata. Radial mycelial growth of each pathogen was measured in PDA Petri dishes amended with food preservatives at 0.2, 1.0, or 2.0% (v/v) after 3, 5, and 7 days of incubation at 25 °C. Selected additives and concentrations were tested as antifungal ingredients of hydroxypropyl methylcellulose (HPMC)-lipid edible coatings. The curative activity of stable coatings was tested in in vivo experiments. Cherry tomatoes were artificially inoculated with the pathogens, coated by immersion about 24 h later, and incubated at 20 °C and 90% RH. Disease incidence and severity (lesion diameter) were determined after 6, 10, and 15 days of incubation and the 'area under the disease progress stairs' (AUDPS) was calculated. In general, HPMC-lipid antifungal coatings controlled black spot caused by A. alternata more effectively than gray mold caused by B. cinerea. Overall, the best results for reduction of gray mold on cherry tomato fruit were obtained with coatings containing 2.0% of potassium carbonate, ammonium phosphate, potassium bicarbonate, or ammonium carbonate, while 2.0% sodium methylparaben, sodium ethylparaben, and sodium propylparaben were the best ingredients for coatings against black rot. © 2013 Elsevier B.V. All rights reserved.

    20. Oregano (Lippia graveolens) essential oil added within pectin edible coatings prevents fungal decay and increases the antioxidant capacity of treated tomatoes.

      Science.gov (United States)

      Rodriguez-Garcia, Isela; Cruz-Valenzuela, M Reynaldo; Silva-Espinoza, Brenda A; Gonzalez-Aguilar, Gustavo A; Moctezuma, Edgar; Gutierrez-Pacheco, M Melissa; Tapia-Rodriguez, Melvin R; Ortega-Ramirez, Luis A; Ayala-Zavala, J Fernando

      2016-08-01

      Tomato is a fruit widely consumed due to its flavor and nutritional value; however, it is susceptible to fungi contamination. Oregano essential oil (OEO) is a fungicide whose constituents are volatile; therefore, their incorporation within edible coatings can protect them and maintain their efficacy. In this context, this study evaluated the effect of OEO applied within pectin coatings on the inhibition of Alternaria alternata growth, antioxidant content and sensorial acceptability of tomatoes. The major volatile compounds of OEO were carvacrol (47.41%), p-cymene (26.44%) and thymol (3.02%). All the applied OEO concentrations (15.7, 25.9 and 36.1 g L(-1) ) inhibited the in vitro growth of A. alternata, whereas the in vivo effective concentrations were 25.9 and 36.1 g L(-1) . Additionally, there was an increment of total phenols and antioxidant activity in coated tomatoes compared to controls. Aroma acceptability of tomatoes was not affected by the pectin-OEO coating; additionally, the pectin, pectin-OEO 15.7 g L(-1) treatments and control tomatoes showed higher flavor acceptability than those coated with pectin-OEO 25.9 and 36.1 g L(-1) . Pectin-OEO coatings showed antifungal effect and increased the antioxidant activity without negative effects on the sensorial acceptability of tomatoes. © 2015 Society of Chemical Industry. © 2015 Society of Chemical Industry.

    1. Method and coating composition for protecting and decontaminating surfaces

      Science.gov (United States)

      Overhold, D C; Peterson, M D

      1959-03-10

      A protective coating useful in the decontamination of surfaces exposed to radioactive substances is described. This coating is placed on the surface before use and is soluble in water, allowing its easy removal in the event decontamination becomes necessary. Suitable coating compositions may be prepared by mixing a water soluble carbohydrate such as sucrose or dextrin, together with a hygroscopic agent such as calcium chloride or zinc chloride.

    2. Effect of a gelatin-based edible coating containing cellulose nanocrystals (CNC) on the quality and nutrient retention of fresh strawberries during storage

      Science.gov (United States)

      Fakhouri, F. M.; Casari, A. C. A.; Mariano, M.; Yamashita, F.; Innocnentini Mei, L. H.; Soldi, V.; Martelli, S. M.

      2014-08-01

      Strawberry is a non-climacteric fruit with a very short postharvest shelf-life. Loss of quality in this fruit is mostly due to its relatively high metabolic activity and sensitivity to fungal decay, meanly grey mold (Botrytis cinerea). In this study, the ability of gelatin coatings containing cellulose nanocrystals (CNC) to extend the shelf-life of strawberry fruit (Fragaria ananassa) over 8 days were studied. The filmogenic solution was obtained by the hydration of 5 g of gelatin (GEL) in 100 mL of distillated water containing different amounts of CNC dispersion (10 mg CNC/g of GEL or 50 mg of CNC/g of GEL) for 1 hour at room temperature. After this period, the solution was heated to 70 °C and maintained at this temperature for 10 minutes. The plasticizer (glycerol) (10g/100g of the GEL) was then added with constant, gentle stirring in order to avoid forming air bubbles and also to avoid gelatin denaturation until complete homogenization. Strawberries (purchased at the local market) were immersed in the filmogenic solution for 1 minute and after coated were dried at 15 °C by 24 hours. The strawberries were then kept under refrigeration and characterized in terms of their properties (weight loss, ascorbic acid content, titratable acidity, water content). The results have shown that samples covered with GEL/CNC had a significant improvement in its shelf- life. For instance, for the control sample (without coating) the weight loss after 8 days of storage was around 65%, while covered samples loss in the range of 31-36%. Edible coating was also effective in the retention of ascorbic acid (AA) in the strawberries, while control sample presented a fast decay in the AA content, covered samples showed a slow decay in the AA concentration. Moreover, the use of GEL/CNC edible coating had an antimicrobial effect in the fruits.

    3. Effect of a gelatin-based edible coating containing cellulose nanocrystals (CNC) on the quality and nutrient retention of fresh strawberries during storage

      International Nuclear Information System (INIS)

      Fakhouri, F M; Casari, A C A; Martelli, S M; Mariano, M; Soldi, V; Yamashita, F; Mei, L H Innocnentini

      2014-01-01

      Strawberry is a non-climacteric fruit with a very short postharvest shelf-life. Loss of quality in this fruit is mostly due to its relatively high metabolic activity and sensitivity to fungal decay, meanly grey mold (Botrytis cinerea). In this study, the ability of gelatin coatings containing cellulose nanocrystals (CNC) to extend the shelf-life of strawberry fruit (Fragaria ananassa) over 8 days were studied. The filmogenic solution was obtained by the hydration of 5 g of gelatin (GEL) in 100 mL of distillated water containing different amounts of CNC dispersion (10 mg CNC/g of GEL or 50 mg of CNC/g of GEL) for 1 hour at room temperature. After this period, the solution was heated to 70 °C and maintained at this temperature for 10 minutes. The plasticizer (glycerol) (10g/100g of the GEL) was then added with constant, gentle stirring in order to avoid forming air bubbles and also to avoid gelatin denaturation until complete homogenization. Strawberries (purchased at the local market) were immersed in the filmogenic solution for 1 minute and after coated were dried at 15 °C by 24 hours. The strawberries were then kept under refrigeration and characterized in terms of their properties (weight loss, ascorbic acid content, titratable acidity, water content). The results have shown that samples covered with GEL/CNC had a significant improvement in its shelf- life. For instance, for the control sample (without coating) the weight loss after 8 days of storage was around 65%, while covered samples loss in the range of 31-36%. Edible coating was also effective in the retention of ascorbic acid (AA) in the strawberries, while control sample presented a fast decay in the AA content, covered samples showed a slow decay in the AA concentration. Moreover, the use of GEL/CNC edible coating had an antimicrobial effect in the fruits

    4. The Effect of Edible Coating Enriched With Kaffir Lime Leaf Essential Oil (Citrus hystrix DC) on Beef Sausage Quality During Frozen Storage (-18°±2°C)

      Science.gov (United States)

      Utami, R.; Kawiji; Khasanah, L. U.; Solikhah, R.

      2018-03-01

      The aim of this study was to determine the effect of edible coating enriched with kaffir lime (Citrus hystrix DC) leaves essential oil at various concentration on beef sausage quality during frozen storage (-18°±2°C). The concentration of kaffir lime leaves essential oil enriched in edible coating were varied at 0%; 0.2%; 1.4%. Microbiological, physical and chemical characteristics (TPC, color, TBA, TVB, and pH) were investigated at 0, 1, 2, 3, and 4 months of storage. The result showed that edible coating with the addition of kaffir lime leaves essential oils decreased the microbial growth, TVB value, and TBA value of beef sausage. The color and pH of samples can be stabilized during storage. The selected kaffir lime leaves essential oil concentrations based on microbial, physical, and chemical characteristics of beef sausages during frozen storage at -18°C was 0.2%.

    5. Nickel/Diamond Composite Coating Prepared by High Speed Electrodeposition

      Directory of Open Access Journals (Sweden)

      ZHANG Yan

      2016-10-01

      Full Text Available Nickel/diamond composite coatings were prepared on the basis of a new high speed electroplating bath. The influence of additives, plating parameters and diamond concentration on internal stress was investigated in order to find the solution to decrease the stress introduced by high current density; the micro morphology of the coatings were observed by SEM. The bath and depositing parameters were optimized that thick nickel/diamond composite coatings with low internal stress can be high speed electroplated with a high cathode current density of 30A/dm2. The results show that when plated with bath composition and parameters as follows: sodium dodecyl sulfate 0.5g/L, ammonium acetate 3g/L, sodium citrate 1.5g/L, diamond particles 30g/L; pH value 3-4, temperature 50℃, the composite coatings prepared in high speed have the lowest internal stress.

    6. Electroless alloy/composite coatings: A review

      Indian Academy of Sciences (India)

      M. Senthilkumar (Newgen Imaging) 1461 1996 Oct 15 13:05:22

      pharmaceutical ... Four types of reducing agent have been used for electroless nickel bath including ..... coatings, however, the bath is more stable at a pH of about 9. 5. ..... ite coating by dry sliding tests with a slider-on-cylinder tribometer in ...

    7. Hybrid laser technology for composite coating and medical applications

      Czech Academy of Sciences Publication Activity Database

      Jelínek, Miroslav; Kocourek, Tomáš; Písařík, Petr; Mikšovský, Jan; Remsa, Jan; Mihailescu, I. N.; Kopeček, Jaromír

      2014-01-01

      Roč. 10, č. 1 (2014), s. 1-8 ISSN 1823-3430 R&D Projects: GA ČR(CZ) GA101/09/0702; GA MŠk LD12069 Institutional support: RVO:68378271 Keywords : hybrid technology * pulsed laser deposition * biocompatible composites * doped coating * composite coating Subject RIV: BM - Solid Matter Physics ; Magnetism http://web.usm.my/jes/pastIssue.html

    8. Wear and impact resistance of HVOF sprayedceramic matrix composites coating

      Science.gov (United States)

      Prawara, B.; Martides, E.; Priyono, B.; Ardy, H.; Rikardo, N.

      2016-02-01

      Ceramic coating has the mechanical properties of high hardness and it is well known for application on wear resistance, but on the other hand the resistance to impact load is low. Therefore its use is limited to applications that have no impact loading. The aim of this research was to obtain ceramic-metallic composite coating which has improved impact resistance compared to conventional ceramic coating. The high impact resistance of ceramic-metallic composite coating is obtained from dispersed metallic alloy phase in ceramic matrix. Ceramic Matrix Composites (CMC) powder with chrome carbide (Cr3C2) base and ceramic-metal NiAl-Al2O3 with various particle sizes as reinforced particle was deposited on mild steel substrate with High Velocity Oxygen Fuel (HVOF) thermal spray coating. Repeated impact test showed that reinforced metallic phase size influenced impact resistance of CMC coating. The ability of CMC coating to absorb impact energy has improved eight times and ten times compared with original Cr3C2 and hard chrome plating respectively. On the other hand the high temperature corrosion resistance of CMC coating showed up to 31 cycles of heating at 800°C and water quenching cooling.

    9. Tribological wear behavior of diamond reinforced composite coating

      International Nuclear Information System (INIS)

      Venkateswarlu, K.; Ray, Ajoy Kumar; Gunjan, Manoj Kumar; Mondal, D.P.; Pathak, L.C.

      2006-01-01

      In the present study, diamond reinforced composite (DRC) coating has been applied on mild steel substrate using thermal spray coating technique. The composite powder consists of diamond, tungsten carbide, and bronze, which was mixed in a ball mill prior deposition by thermal spray. The microstructure and the distribution of diamond and tungsten carbide particle in the bronze matrix were studied. The DRC-coated mild steel substrates were assessed in terms of their high stress abrasive wear and compared with that of uncoated mild steel substrates. It was observed that when sliding against steel, the DRC-coated sample initially gains weight, but then loses the transferred counter surface material. In case of abrasive wear, the wear rate was greatly reduced due to the coating; wherein the wear rate decreased with increase in diamond content

    10. Carbide coated fibers in graphite-aluminum composites

      Science.gov (United States)

      Imprescia, R. J.; Levinson, L. S.; Reiswig, R. D.; Wallace, T. C.; Williams, J. M.

      1975-01-01

      The NASA-supported program at the Los Alamos Scientific Laboratory (LASL) to develop carbon fiber-aluminum matrix composites is described. Chemical vapor deposition (CVD) was used to uniformly deposit thin, smooth, continuous coats of TiC on the fibers of graphite tows. Wet chemical coating of fibers, followed by high-temperature treatment, was also used, but showed little promise as an alternative coating method. Strength measurements on CVD coated fiber tows showed that thin carbide coats can add to fiber strength. The ability of aluminum alloys to wet TiC was successfully demonstrated using TiC-coated graphite surfaces. Pressure-infiltration of TiC- and ZrC-coated fiber tows with aluminum alloys was only partially successful. Experiments were performed to evaluate the effectiveness of carbide coats on carbon as barriers to prevent reaction between alluminum alloys and carbon. Initial results indicate that composites of aluminum and carbide-coated graphite are stable for long periods of time at temperatures near the alloy solidus.

    11. Laser Cladding of Composite Bioceramic Coatings on Titanium Alloy

      Science.gov (United States)

      Xu, Xiang; Han, Jiege; Wang, Chunming; Huang, Anguo

      2016-02-01

      In this study, silicon nitride (Si3N4) and calcium phosphate tribasic (TCP) composite bioceramic coatings were fabricated on a Ti6Al4V (TC4) alloy using Nd:YAG pulsed laser, CO2 CW laser, and Semiconductor CW laser. The surface morphology, cross-sectional microstructure, mechanical properties, and biological behavior were carefully investigated. These investigations were conducted employing scanning electron microscope, energy-dispersive x-ray spectroscopy, and other methodologies. The results showed that both Si3N4 and Si3N4/TCP composite coatings were able to form a compact bonding interface between the coating and the substrate by using appropriate laser parameters. The coating layers were dense, demonstrating a good surface appearance. The bioceramic coatings produced by laser cladding have good mechanical properties. Compared with that of the bulk material, microhardness of composite ceramic coatings on the surface significantly increased. In addition, good biological activity could be obtained by adding TCP into the composite coating.

    12. Study of Plasma Electrolytic Oxidation Coatings on Aluminum Composites

      Directory of Open Access Journals (Sweden)

      Leonid Agureev

      2018-06-01

      Full Text Available Coatings, with a thickness of up to 75 µm, were formed by plasma electrolytic oxidation (PEO under the alternating current electrical mode in a silicate-alkaline electrolyte on aluminum composites without additives and alloyed with copper (1–4.5%. The coatings’ structure was analyzed by scanning electron microscopy, X-ray microanalysis, X-ray photoelectron spectroscopy, nuclear backscattering spectrometry, and XRD analysis. The coatings formed for 60 min were characterized by excessive aluminum content and the presence of low-temperature modifications of alumina γ-Al2O3 and η-Al2O3. The coatings formed for 180 min additionally contained high-temperature corundum α-Al2O3, and aluminum inclusions were absent. The electrochemical behavior of coated composites and uncoated ones in 3% NaCl was studied. Alloyage of aluminum composites with copper increased the corrosion current density. Plasma electrolytic oxidation reduced it several times.

    13. Evaluation of an edible coating based whey protein and beeswax on the physical and chemical quality of gooseberry (Physalis peruviana L.

      Directory of Open Access Journals (Sweden)

      Oswaldo Osorio Mora

      2016-10-01

      Full Text Available It was developed and optimized an edible coating based whey protein concentrate and beeswax. An experimental design 32 was used, this was evaluated by response surface methodology, it was obtained that the optimal formulation with a concentration of 15% beeswax and 10% whey protein, reduced by 35.49% weight loss of the fruit with respect to weight loss of control treatments. The optimal treatment was characterized and evaluated on the physicochemical properties of the gooseberry (Physalis peruviana L. in two storage conditions: environment (17- 2 ºC y HR: 69% and cooling (4 -2 ºC y HR: 66%. The results for the 15th day evaluation indicated a decrease in the percentage of weight loss, in storage environment and cooling (36.20% and 41.50% respectively. Control treatments decreased acidity in storage environment and cooling 3.88% and 4.92% respectively, compared to coating treatments. pH have not significantly change with any treatment. The coating prevent reduction of soluble solids 3.76% to environmental conditions and 2.27% to cooling conditions. For maturity index were not any significant changes between control treatments and coating treatments, in both conditions. The firmness remained without any significant changes except treatment environment uncoated, this presented a loss of firmness of 12.04% compared to the treatment environment coated. The respiration rate indicates a climacteric peak at day 8th for environment and at day 10th for cooling. For some properties, the cooling treatment uncoated and environment treatment coated have not any significant changes whereby the coating application can be an alternative to the cooling.

    14. Effect of the Fish Oil Fortified Chitosan Edible Film on Microbiological, Chemical Composition and Sensory Properties of Göbek Kashar Cheese during Ripening Time.

      Science.gov (United States)

      Yangilar, Filiz

      2016-01-01

      Objective of the present study is to investigate the effect of coated edible films with chitosan solutions enriched with essential oil (EO) on the chemical, microbial and sensory properties of Kashar cheese during ripening time. Generally, no differences were found in total aerobic mesophilic bacteria, streptococci and lactoccocci counts among cheeses but these microorganism counts increased during 60 and 90 d storage especially in C1 (uncoated sample) as compared with coated samples. Antimicrobial effectiveness of the films against moulds was measured on 30, 60, and 90 d of storage. In addition of fish EO into chitosan edible films samples were showed to affect significantly decreased the moulds (poil (1% w/v) fortified chitosan film) on the 90(th) d, while in C1 as 3.89 Log CFU/g on the 90(th) d of ripening. Compared to other cheese samples, C2 (coated with chitosan film) and C4 coated cheese samples revealed higher levels of water-soluble nitrogen and ripening index at the end of storage. C2 coated cheese samples were preferred more by the panellists while C4 coated cheese samples received the lowest scores.

    15. Sol-gel coatings on carbon/carbon composites

      International Nuclear Information System (INIS)

      Sim, S.M.; Krabill, R.M.; Dalzell, W.J. Jr.; Chu, P.Y.; Clark, D.E.

      1986-01-01

      The need for structural materials that can withstand severe environments up to 4000 0 F has promulgated the investigation of sol-gel derived ceramic and composite coatings on carbon/carbon composite materials. Alumina and zirconia sols have been deposited via thermophoresis on carbon/carbon substrates

    16. Fatty acids and astaxanthin composition of two edible native Mexican crayfish Cambarellus (C.) montezumae and Procambarus (M.) bouvieri

      International Nuclear Information System (INIS)

      Coral-Hinostroza, G.; Diaz-Martinez, M.; Huberman, A.; Silencio-Barrita, J.L.

      2016-01-01

      The content and composition of the fatty acids (F As) and astaxanthin (AST) in the edible forms of crayfish: the whole animal of Cambarellus (C.) montezumae, and the tail meat (TM) of Procambarus (M.) bouvieri were determined by GC and HPLC. The exoskeleton (EXK) of P. (M.) bouvieri was also studied. Unsaturated FAs, and mostly oleic acid (C18:1 n-9), were predominant in both edible forms. The contents of the polyunsaturated eicosapentaenoic (C20:5 n-3, EPA), arachidonic (C20:4 n-6, ARA) and docosahexaenoic acid (C22:6 n-3, DHA), were higher in the TM of P. (M.) bouvieri than in the complete C. (C.) montezumae (p 79.50%). AST esters were enriched with saturated FAs in C. (C.) montezumae and with PUFAs in EXK of P. (M.) bouvieri. We conclude that both C. (C.) montezumae and the TM of P. (M.) bouvieri are traditional foods rich in n-3 PUFAs and C. (C.) montezumae in AST. The EXK of P. (M.) bouvieri is a rich potential source of AST, n-3 PUFAs, and the combination AST-DHA. [es

    17. Electrophoretic deposition of composite hydroxyapatite-chitosan coatings

      International Nuclear Information System (INIS)

      Pang Xin; Zhitomirsky, Igor

      2007-01-01

      Cathodic electrophoretic deposition has been utilized for the fabrication of composite hydroxyapatite-chitosan coatings on 316L stainless steel substrates. The addition of chitosan to the hydroxyapatite suspensions promoted the electrophoretic deposition of the hydroxyapatite nanoparticles and resulted in the formation of composite coatings. The obtained coatings were investigated by X-ray diffraction, thermogravimetric and differential thermal analysis, scanning and transmission electron microscopy, potentiodynamic polarization measurements, and electrochemical impedance spectroscopy. It was shown that the deposit composition can be changed by a variation of the chitosan or hydroxyapatite concentration in the solutions. Experimental conditions were developed for the fabrication of hydroxyapatite-chitosan nanocomposites containing 40.9-89.8 wt.% hydroxyapatite. The method enabled the formation of adherent and uniform coatings of thicknesses up to 60 μm. X-ray studies revealed that the preferred orientation of the hydroxyapatite nanoparticles in the chitosan matrix increases with decreasing hydroxyapatite content in the composite coatings. The obtained coatings provided the corrosion protection for the 316L stainless steel substrates

    18. Review of Research Work on Ti-BASED Composite Coatings

      Science.gov (United States)

      Gabbitas, Brian; Salman, Asma; Zhang, Deliang; Cao, Peng

      The service life of industrial components is limited predominantly by Chemical corrosion/mechanical wear. The project is concerned with the investigation of the capability of Ti(Al,O)/Al2O3 coatings to improve the service life of tool steel (H13) used for dies in aluminium high pressure die casting. This paper gives a general review on the research work conducted at the University of Waikato on producing and evaluating the titanium/alumina based composite coatings. The powder feedstocks for making the composite coatings were produced by high energy mechanical milling of a mixture of Al and TiO2 powders in two different molar ratios followed by a thermal reaction process. The feedstocks were then thermally sprayed using a high velocity air-fuel (HVAF) technique on H13 steel substrates to produce a Ti(Al,O)/Al2O3 composite coatings. The performance of the coating was assessed in terms of thermal shock resistance and reaction kinetics with molten aluminium. The composite powders and coatings were characterized using scanning electron microscopy (SEM), optical microscopy and X-ray diffractometry (XRD).

    19. Composite Coatings of Chromium and Nanodiamond Particles on Steel

      Directory of Open Access Journals (Sweden)

      Gidikova N.

      2017-12-01

      Full Text Available Chrome plating is used to improve the properties of metal surfaces like hardness, corrosion resistance and wear resistance in machine building. To further improve these properties, an electrodeposited chromium coating on steel, modified with nanodiamond particles is proposed. The nanodiamond particles (average size 4 nm measured by TEM are produced by detonation synthesis (NDDS. The composite coating (Cr+NDDS has an increased thickness, about two times greater microhardness and finer micro-structure compared to that of unmodified chromium coating obtained under the same galvanization conditions. In the microstructure of specimen obtained from chrome electrolyte with concentration of NDDS 25 g/l or more, “minisections” with chromium shell were found. They were identified by metallographic microscope and X-ray analyser on etched section of chromium plated sample. The object of further research is the dependence of the presence of NDDS in the composite coating from the nanodiamond particles concentration in the chroming electrolyte.

    20. Stress development in particulate, nano-composite and polymeric coatings

      Science.gov (United States)

      Jindal, Karan

      2009-12-01

      The main goal of this research is to study the stress, structural and mechanical property development during the drying of particulate coatings, nano-composite coatings and VOC compliant refinish clearcoats. The results obtained during this research establish the mechanism for the stress development during drying in various coating systems. Coating stress was measured using a controlled environment stress apparatus based on cantilever deflection principle. The stress evolution in alumina coatings made of 0.4 mum size alumina particles was studied and the effect of a lateral drying was investigated. The stress does not develop until the later stages of drying. A peak stress was observed during drying and the peak stress originates due to the formation of pendular rings between the particles. Silica nanocomposite coatings were fabricated from suspension of nano sized silicon dioxide particles (20 nm) and polyvinyl alcohol (PVA) polymer. The stress in silica nano-composite goes through maximum as the amount of polymer in the coating increases. The highest final stress was found to be ˜ 110MPa at a PVA content of 60 wt%. Observations from SEM, nitrogen gas adsorption, camera imaging, and nano-indentation were also studied to correlate the coatings properties during drying to measured stress. A model VOC compliant two component (2K) acrylic-polyol refinish clearcoat was prepared to study the effects of a new additive on drying, curing, rheology and stress development at room temperature. Most of the drying of the low VOC coatings occurred before appreciable (20%) crosslinking. Tensile stress developed in the same timeframe as drying and then relaxed over a longer time scale. Model low VOC coatings prepared with the additive had higher peak stresses than those without the additive. In addition, rheological data showed that the additive resulted in greater viscosity buildup during drying.

    1. Nutritional and antinutritional composition of the five species of aquatic edible insects consumed in Manipur, India.

      Science.gov (United States)

      Shantibala, T; Lokeshwari, R K; Debaraj, H

      2014-01-26

      The people living in Manipur have a distinct identity, culture, and food habits. They have a prototype culture of eating insects. In our study, the nutritive contents of five potentially-edible aquatic insects, Lethocerus indicus (Lepeletier and Serville) (Hemiptera: Belostomatidae), Laccotrephes maculatus (F.) (Nepidae), Hydrophilus olivaceous (F.) (Coleoptera: Dytiscidae), Cybister tripunctatus (Olivier), and Crocothemis servilia (Drury) (Odonata: Libellulidae), were analyzed to inform consumers about the nutritional quality of the insects and the suggested quantity of their intake. A good amount of protein content and high gross energy was recorded among the insects. The results showed high levels of sodium, calcium, and magnesium present in the insects, indicating that they are a good source of minerals. Antinutritional properties of these insects were below 0.52%, which is a non-toxic level. Aquatic insects, such as C. tripunctatus, also possesses strong antioxidant activity (110 µg/mL). Therefore, these insects can play a major role in food security, health, and environment management. It is essential to cultivate edible insects to maintain their population sustainability. This is an open access paper. We use the Creative Commons Attribution 3.0 license that permits unrestricted use, provided that the paper is properly attributed.

    2. Laser-induced reaction alumina coating on ceramic composite

      Science.gov (United States)

      Xiao, Chenghe

      Silicon carbide ceramics are susceptible to corrosion by certain industrial furnace environments. It is also true for a new class of silicon carbide-particulate reinforced alumina-matrix composite (SiCsb(P)Alsb2Osb3) since it contains more than 55% of SiC particulate within the composite. This behavior would limit the use of SiCsb(P)Alsb2Osb3 composites in ceramic heat exchangers. Because oxide ceramics corrode substantially less in the same environments, a laser-induced reaction alumina coating technique has been developed for improving corrosion resistance of the SiCsb(P)Alsb2Osb3 composite. Specimens with and without the laser-induced reaction alumina coating were subjected to corrosion testing at 1200sp°C in an air atmosphere containing Nasb2COsb3 for 50 ˜ 200 hours. Corroded specimens were characterized via x-ray diffraction (XRD), scanning electron microscopy (SEM), and energy dispersive spectrometer (EDS). The uncoated SiCsbP/Alsb2Osb3 composite samples experienced an initial increase in weight during the exposure to Nasb2COsb3 at 1200sp°C due to the oxidation of residual aluminum metal in the composite. There was no significant weight change difference experienced during exposure times between 50 and 200 hours. The oxidation layer formed on the as-received composite surface consisted of Si and Alsb2Osb3 (after washing with a HF solution). The oxidation layer grew outward and inward from the original surface of the composite. The growth rate in the outward direction was faster than in the inward direction. The formation of the Si/Alsb2Osb3 oxidation layer on the as-received composite was nonuniform, and localized corrosion was observed. The coated samples experienced very little mass increase. The laser-induced reaction alumina coating effectively provided protection for the SiCsbP/Alsb2Osb3 composite by keeping the corrodents from contacting the composite and by the formation of some refractory compounds such as Nasb2OAlsb2Osb3SiOsb2 and Nasb2Alsb{22}Osb

    3. Cirrus Dopant Nano-Composite Coatings

      Science.gov (United States)

      2014-11-01

      coatings without alteration to the existing plating process. Glen Slater, Cirrus Materials | Stephen Flint, Auckland UniServices Ltd Report...ADDRESS(ES) University of Auckland ,Cirrus Materials, Auckland , New Zealand, 8. PERFORMING ORGANIZATION REPORT NUMBER 9. SPONSORING/MONITORING AGENCY...JiA/ g THE UNIVERSITY ’-" OF AUCKLAND NEW ZEALAND Te Whare Wanan a o Thmaki Makaurau ~"""’ • ........,." ... Southwest Pacific Basin . p

    4. Interfacial Coatings for Inorganic Composite Insulation Systems

      International Nuclear Information System (INIS)

      Hooker, M. W.; Fabian, P. E.; Stewart, M. W.; Grandlienard, S. D.; Kano, K. S.

      2006-01-01

      Inorganic (ceramic) insulation materials are known to have good radiation resistance and desirable electrical and mechanical properties at cryogenic and elevated temperatures. In addition, ceramic materials can withstand the high-temperature reaction cycle used with Nb3Sn superconductor materials, allowing the insulation to be co-processed with the superconductor in a wind-and-react fabrication process. A critical aspect in the manufacture of ceramic-based insulation systems is the deposition of suitable fiber-coating materials that prevent chemical reaction of the fiber and matrix materials, and thus provide a compliant interface between the fiber and matrix, which minimizes the impact of brittle failure of the ceramic matrix. Ceramic insulation produced with CTD-FI-202 fiber interfaces have been found to exhibit very high shear and compressive strengths. However, this material is costly to produce. Thus, the goal of the present work is to evaluate alternative, lower-cost materials and processes. A variety of oxide and polyimide coatings were evaluated, and one commercially available polyimide coating has been shown to provide some improvement as compared to uncoated and de-sized S2 glass

    5. Characterization of edible coatings consisting of pea starch, whey protein isolate, and Carnauba wax and their effects on oil rancidity and sensory properties of walnuts and pine nuts.

      Science.gov (United States)

      Mehyar, Ghadeer F; Al-Ismail, Khalid; Han, Jung H; Chee, Grace W

      2012-02-01

      Edible coatings made of whey protein isolate (WPI), pea starch (PS), and their combinations with carnauba wax (CW) were prepared and characterized. WPI combined with CW formed stable emulsion while PS with CW formed unstable emulsion and both formulations produced non-homogeneous films. Addition of PS to WPI: CW combination at the ratio of 1:1:1, respectively, resulted in stable emulsion and homogenous films. The emulsion PS: WPI: CW (1:1:2) was stable and formed a continuous film but had less homogenous droplets size distribution when compared to 1:1:1 film. Combined films had a reduced tensile strength and elongation compared to single component films. WPI : CW (1:1) films had higher elastic modulus than the WPI films, but the modulus reduced by the addition of PS. All the coating formulations were effective in preventing oxidative and hydrolytic rancidity of walnuts and pine nuts stored at 25 °C throughout the storage (12 d) but were less effective at 50 °C. Increasing the concentration of CW from 1:1:1 to 1:1:2 in PS: WPI: CW formulation did not contribute in further prevention of oil rancidity at 25 °C. Using of PS: WPI: CW (1:1:1) coating on both nuts significantly (P carnauba wax reduced the oxidative and hydrolytic rancidity of the nuts and improved sensory characteristics. © 2012 Institute of Food Technologists®

    6. Effect of gamma irradiation on the appearance and composition of edible mushrooms

      International Nuclear Information System (INIS)

      Wahid, M.; Darwish, Y.M.A.

      1981-01-01

      Fresh edible mushrooms picked with closed caps, and irradiated at 0, 1.0 and 2.5 kGy doses were stored for 8 days at 20+-2 0 C and investigated for the changes in ascorbic acid, protein contents, free alpha-amino N and total phenols. It was observed that during storage free alpha-amino N decreased significantly, while the protein contents remained somewhat constant till 4th day of storage. The ascorbic acid increased in the beginning and then decreased significantly. Total phenols decreased in the beginning and then accumulated during further storage. Irradiation had no effect on the proteins, but decreased ascorbic acid contents of mushrooms. The levels of free alpha-amino N and total phenols were significantly higher in irradiated treatments as compared to unirradiated mushrooms. (author)

    7. Nutritional composition and protein quality of the edible beetle Holotrichia parallela.

      Science.gov (United States)

      Yang, Qingli; Liu, Shaofang; Sun, Jie; Yu, Lina; Zhang, Chushu; Bi, Jie; Yang, Zhen

      2014-10-15

      The adult edible beetle Holotrichia parallela Motschulsky (Coleoptera: Scarabaeoidea) represents a traditional food source in China. Based on nutritional analyses, adult H. parallela is high in protein (70%) and minerals and low in fat. H. parallela contained approximately 10% chitin; the corrected protein content was 66%. Oleic acid and linoleic acid were the most abundant fatty acids. Of the total amino acids in H. parallela, 47.4% were essential amino acids. The amino acid scores were 87 and 100, based on the corrected crude and net protein contents, respectively; threonine was the limiting amino acid. In vitro protein digestibility was 78%, and the protein digestibility-corrected amino acid score was 89 based on the net protein content. Adult H. parallela may be a potential source of proteins and minerals for humans and animals. © The Author 2014. Published by Oxford University Press on behalf of the Entomological Society of America.

    8. Effect of Nanosilica Filled Polyurethane Composite Coating on Polypropylene Substrate

      Directory of Open Access Journals (Sweden)

      Yern Chee Ching

      2013-01-01

      Full Text Available Acrylic based polyurethane (PU coatings with various amounts of nanosilica contents were prepared using solution casting method. The nanosilica (SiO2 particles used are around 16 nm in diameter. The friction and wear test was conducted using the reciprocating wear testing machine. The tests were performed at rotary speed of 100 rpm and 200 rpm with load of 0.1 kg to 0.4 kg under 1 N interval. The effect of the PU/nano-SiO2 composite coating on friction and wear behavior of polypropylene substrate was investigated and compared. The worn surface of coating film layer after testing was investigated by using an optical microscope. The introduction of PU/nanosilica composite coating containing 3 wt% of nano-SiO2 content gives the lowest friction coefficient and wear rate to PP substrate. Both the friction and wear rate of PP substrate coated with >3 wt% of nano-SiO2 filled PU coating would increase with the increasing of applied load and sliding time.

    9. Effect of edible co-polymers coatings using γ-irradiation on Hyani date fruit behavior during marketing.

      Science.gov (United States)

      El-Dein, Asmaa Ezz; Khozemy, Ehab E; Farag, Serag A; Abd El-Hamed, N; Dosoukey, I M

      2018-05-24

      The present work introduces a preparation of coating fruits film from natural biodegradable materials with evaluation of its efficiency in keeping the quality of fresh date fruits. Triple blend (Tb) which involved PVA, chitosan (Cs) and tannic (TA) acids was studied in preservation of Rutab (Hyani) date. Antimicrobial characters besides decay of fruits during a cold storage were determined. The blend solutions were exposed to the γ-irradiation (5.0 to 20 kGy) before casting or use. The effects of polymer composition and irradiation dose on the mechanical and thermo-mechanical properties were studied. The obtained results showed that γ-irradiation and the addition of tannic acid (TA) increased the mechanical properties of the films and the shelf-life of Rutab (Hyani) date during the marketing period (12 ± 2 °C, 98%, RH) from one week to one month of marketing period for consumers with accepted freshness and quality. Copyright © 2018 Elsevier B.V. All rights reserved.

    10. Hydrogel-Electrospun Fiber Mat Composite Coatings for Neural Prostheses

      Directory of Open Access Journals (Sweden)

      Ning eHan

      2011-03-01

      Full Text Available Achieving stable, long-term performance of implanted neural prosthetic devices has been challenging because of implantation related neuron loss and a foreign body response that results in encapsulating glial scar formation. To improve neuron-prosthesis integration and form chronic, stable interfaces, we investigated the potential of neurotrophin-eluting hydrogel-electrospun fiber mat (EFM composite coatings. In particular, poly(ethylene glycol-poly(ε-caprolactone (PEGPCL hydrogel- poly(ε-caprolactone (PCL EFM composites were applied as coatings for multielectrode arrays (MEAs. Coatings were stable and persisted on electrode surfaces for over 1 month under an agarose gel tissue phantom and over 9 months in a PBS immersion bath. To demonstrate drug release, a neurotrophin, nerve growth factor (NGF, was loaded in the PEGPCL hydrogel layer, and coating cytotoxicity and sustained NGF release were evaluated using a PC12 cell culture model. Quantitative MTT assays showed that these coatings had no significant toxicity toward PC12 cells, and neurite extension at day 7 and 14 confirmed sustained release of NGF at biologically significant concentrations for at least 2 weeks. Our results demonstrate that hydrogel-EFM composite materials can be applied to neural prostheses as a means to improve neuron-electrode proximity and enhance long-term device performance and function.

    11. Poly (lactic acid organoclay nano composites for paper coating applications

      Directory of Open Access Journals (Sweden)

      Tatcha Sonjui

      2014-10-01

      Full Text Available Poly(lactic acid or PLA is a well-known biodegradable polymer derived from renewable resources such as corn strach, tapioca strach, and sugar cane. PLA is the most extensively utilized biodegradable polyester with potential to replace conventional petrochemical-based polymers. However, PLA has some drawbacks, such as brittleness and poor gas barrier properties. Nano composite polymers have experience and increasing interest due to their characteristics, especially in mechanical and thermal properties. The objectives of this research were to prepare PLA formulations using three different PLAs. The formulas giving high gloss coating film were selected to prepare nano composite film by incorporated with different amount of various types of organoclays. The physical properties of the PLA coating films were studied and it was found that the PLA 7000D with 0.1%w/w of Cloisite 30B provided decent viscosity for coating process. In addition, the nano composite coating films showed good physical properties such as high gloss, good adhesion, and good hardness. There is a possibility of using the obtained formulation as a paper coating film.

    12. Oxidation resistant coatings for ceramic matrix composite components

      Energy Technology Data Exchange (ETDEWEB)

      Vaubert, V.M.; Stinton, D.P. [Oak Ridge National Lab., TN (United States); Hirschfeld, D.A. [New Mexico Inst. of Mining and Technology, Socorro, NM (United States). Dept. of Materials and Metallurgical Engineering

      1998-11-01

      Corrosion resistant Ca{sub 0.6}Mg{sub 0.4}Zr{sub 4}(PO{sub 4}){sub 6} (CMZP) and Ca{sub 0.5}Sr{sub 0.5}Zr{sub 4}(PO{sub 4}){sub 6} (CS-50) coatings for fiber-reinforced SiC-matrix composite heat exchanger tubes have been developed. Aqueous slurries of both oxides were prepared with high solids loading. One coating process consisted of dipping the samples in a slip. A tape casting process has also been created that produced relatively thin and dense coatings covering a large area. A processing technique was developed, utilizing a pre-sintering step, which produced coatings with minimal cracking.

    13. Microstructure and Properties of Composite Coatings Obtained on Aluminium Alloys

      Directory of Open Access Journals (Sweden)

      Bara M.

      2016-09-01

      Full Text Available This paper presents methods of modifying the anode surface layers of Al2O3 by introducing carbon to their microstructure. Composite coatings were prepared using two different methods. In the first, coatings were formed by means of oxidation under constant current conditions. Anodic oxidation of aluminium was conducted in a multicomponent electrolyte with the addition of organic acids and graphite. The second method was based on the formation of oxide coatings in an electrolyte without the addition of graphite or heat treatment of the layers of succinic acid. The obtained coatings were tested using SEM, TEM, and GDOES (glow discharge optical emission spectrometry and their tribological and stereometric properties were measured. The study demonstrated the beneficial effects of the methods when used to improve the tribological properties of sliding couples.

    14. Biocatalytically active silCoat-composites entrapping viable Escherichia coli.

      Science.gov (United States)

      Findeisen, A; Thum, O; Ansorge-Schumacher, M B

      2014-02-01

      Application of whole cells in industrial processes requires high catalytic activity, manageability, and viability under technical conditions, which can in principle be accomplished by appropriate immobilization. Here, we report the identification of carrier material allowing exceptionally efficient adsorptive binding of Escherichia coli whole cells hosting catalytically active carbonyl reductase from Candida parapsilosis (CPCR2). With the immobilizates, composite formation with both hydrophobic and hydrophilized silicone was achieved, yielding advanced silCoat-material and HYsilCoat-material, respectively. HYsilCoat-whole cells were viable preparations with a cell loading up to 400 mg(E. coli) · g(-1)(carrier) and considerably lower leaching than native immobilizates. SilCoat-whole cells performed particularly well in neat substrate exhibiting distinctly increased catalytic activity.

    15. HfC plasma coating of C/C composites

      International Nuclear Information System (INIS)

      Boncoeur, M.; Schnedecker, G.; Lulewicz, J.D.

      1992-01-01

      The surface properties of C/C composites such as hardness and corrosion or erosion resistance can be modified by a ceramic coating applied by plasma torch. The technique of plasma spraying in controlled temperature and atmosphere, that was developed and patented by the CEA, makes it possible to apply coatings to the majority of metals and ceramics without affecting the characteristics of the composite. An example of hard deposit of HfC on a C/C composite is described. The characteristics of the deposit and of the bonding with the C/C composite were studied before and after a heat treatment under vacuum for 2 hours at 1000 C. 2 refs

    16. Potential assisted fabrication of metal-ceramic composite coatings

      International Nuclear Information System (INIS)

      Knote, A.; Schindler, U.; Krueger, H.G.; Kern, H.

      2003-01-01

      A possibility to produce uniform metal-ceramic composite coatings with a high content of ceramic particles up to 60 vol.% will be presented in this study. This method includes a combination of electrophoretic deposition and electrolytic deposition by several steps. A yttria-stabilized zirconia coating (Tosoh TZ-8Y) was first electrophoretically deposited on a ferritic steel plate and then sintered by 1100 C to an open porous layer. In the next step nickel was electrodeposited into the pores of the layer. By a final annealing step it was possible to improve the bonding of the composit coating on the substrate by diffusion of the metal components. (Abstract Copyright [2003], Wiley Periodicals, Inc.) [de

    17. Oxidation resistance coating for niobium base structural composites

      International Nuclear Information System (INIS)

      Tabaru, T.; Shobu, K.; Kim, J.H.; Hirai, H.; Hanada, S.

      2003-01-01

      Oxidation behavior of Al-rich Mo(Si,Al) 2 base alloys, which is a candidate material for the oxidation resistance coating on Nb base structural composites, were investigated by thermogravimetry. The Mo(Si,Al) 2 base alloys containing Mo 5 (Si,Al) 3 up to about 10 vol% exhibits excellent oxidation resistance at temperatures ranging from 780 to 1580 K, particularly at 1580 K due to continuous Al 2 O 3 layer development. To evaluate the applicability of the Mo(Si,Al) 2 base coating, plasma spraying on Nb base composites were undertaken. However, interface reaction layer was found to form during the following heat treatment. Preparation of Mo(Si,Al) 2 /Al 2 O 3 /Nb layered structures via powder metallurgical process was attempted to preclude diffusion reaction between coating and substrate. (orig.)

    18. Radiation curable compounds for use in coating compositions

      International Nuclear Information System (INIS)

      Friedlander, C.B.; McMullen, J.C.

      1979-01-01

      Radiation curable compounds are disclosed which are derived from the reaction of a siloxy-containing carbinol, a polyisocyanate and polyfunctional compound having hydroxy and acrylic functional groups. The compounds have high cure rates, are compatible with other components of radiation curable, film forming compositions and impart good slip and other properties to cured film coatings. (author)

    19. Environmental Barrier Coatings for Ceramic Matrix Composites - An Overview

      Science.gov (United States)

      Lee, Kang; Zhu, Dongming; Wiesner, Valerie Lynn; van Roode, Mark; Kashyap, Tania; Zhu, Dongming; Wiesner, Valerie

      2016-01-01

      Ceramic Matrix Composites (CMCs) are increasingly being considered as structural materials for advanced power generation equipment. Broadly speaking the two classes of materials are oxide-based CMCs and non-oxide based CMCs. The non-oxide CMCs are primarily silicon-based. Under conditions prevalent in the gas turbine hot section the water vapor formed in the combustion of gaseous or liquid hydrocarbons reacts with the surface-SiO2 to form volatile products. Progressive surface recession of the SiC-SiC CMC component, strength loss as a result of wall thinning and chemical changes in the component occur, which leads to the loss of structural integrity and mechanical strength and becomes life limiting to the equipment in service. The solutions pursued to improve the life of SiC-SiC CMCs include the incorporation of an external barrier coating to provide surface protection to the CMC substrate. The coating system has become known as an Environmental Barrier Coating (EBC). The relevant early coatings work was focused on coatings for corrosion protection of silicon-based monolithic ceramics operating under severely corrosive conditions. The development of EBCs for gas turbine hot section components was built on the early work for silicon-based monolithics. The first generation EBC is a three-layer coating, which in its simplest configuration consists of a silicon (Si) base coat applied on top of the CMC, a barium-strontium-aluminosilicate (BSAS) surface coat resistant to water vapor attack, and a mullite-based intermediate coating layer between the Si base coat and BSAS top coat. This system can be represented as Si-Mullite-BSAS. While this baseline EBC presented a significant improvement over the uncoated SiC-SiC CMC, for the very long durations of 3-4 years or more expected for industrial operation further improvements in coating durability are desirable. Also, for very demanding applications with higher component temperatures but shorter service lives more rugged EBCs

    20. Edible Coating Using a Chitosan-Based Colloid Incorporating Grapefruit Seed Extract for Cherry Tomato Safety and Preservation.

      Science.gov (United States)

      Won, Jin Sung; Lee, Seung Jo; Park, Hyeon Hwa; Song, Kyung Bin; Min, Sea C

      2018-01-01

      Grapefruit seed extract (GSE)-containing chitosan-based coating was developed and applied to cherry tomatoes to protect them from Salmonella invasion and improve their storability. The coating colloids were produced by mixing a chitosan colloid (1% [w/w] chitosan) with GSE at various concentrations (0.5%, 0.7%, 1.0%, and 1.2% [w/w]) using high-shear mixing (10000 rpm, 2 min). Coatings with chitosan colloids containing GSE at 0.0%, 0.5%, 0.7%, and 1.0% (w/w) inactivated Salmonella on cherry tomatoes by 1.0 ± 0.3, 1.2 ± 0.3, 1.6 ± 0.1, and 2.0 ± 0.3 log CFU/cherry tomato, respectively. Coatings both with and without GSE (1.0%) effectively inhibited the growth of Salmonella and total mesophilic aerobes, reduced CO 2 generation, and retarded titratable acidity decrease during storage at 10 and 25 °C. The advantage of incorporating GSE in the formulation was demonstrated by delayed microorganism growth and reduced weight loss at 25 °C. The chitosan-GSE coating did not affect lycopene concentration, color, and sensory properties (P > 0.05). Chitosan-GSE coating shows potential for improving the microbiological safety and storability of cherry tomatoes, with stronger efficacy at 25 °C than that of chitosan coating without GSE. A novel chitosan coating containing grape fruit seed extract (GSE) improved the microbiological safety against Salmonella and storability of cherry tomatoes without altering their flavor, demonstrating its strong potential as an effective postharvest technology. Chitosan coating containing GSE might be preferable over chitosan coating without GSE for application to tomatoes that are stored at room temperature in that it more effectively inhibits microbial growth and weight loss than the coating without GSE at 25 °C. © 2017 Institute of Food Technologists®.

    1. Infiltration processing of metal matrix composites using coated ceramic particulates

      Science.gov (United States)

      Leon-Patino, Carlos Alberto

      2001-07-01

      A new process was developed to fabricate particulate metal matrix composites (MMCs). The process involves three steps: (1) modifying the particulate surface by metal coating, (2) forming a particulate porous compact; and (3) introducing metal into the channel network by vacuum infiltration. MMCs with different reinforcements, volume fractions, and sizes can be produced by this technique. Powders of alumina and silicon carbide were successfully coated with nickel and copper in preparation for infiltration with molten aluminum. Electroless Ni and Cu deposition was used since it enhances the wettability of the reinforcements for composite fabrication. While Cu deposits were polycrystalline, traces of phosphorous co-deposited from the electroless bath gave an amorphous Ni-P coating. The effect of metal coating on wetting behavior was evaluated at 800°C on plain and metal-coated ceramic plates using a sessile drop technique. The metallic films eliminated the non-wetting behavior of the uncoated ceramics, leading to equilibrium contact angles in the order of 12° and below 58° for Ni and Cu coated ceramics, respectively. The spreading data indicated that local diffusion at the triple junction was the governing mechanism of the wetting process. Precipitation of intermetallic phases in the drop/ceramic interface delayed the formation of Al4C3. Infiltration with molten Al showed that the coated-particulates are suitable as reinforcing materials for fabricating MMCs, giving porosity-free components with a homogeneously distributed reinforcing phase. The coating promoted easy metal flow through the preform, compared to the non-infiltration behavior of the uncoated counterparts. Liquid state diffusion kinetics due to temperature dependent viscosity forces controlled the infiltration process. Microstructural analysis indicated the formation of intermetallic phases such as CuAl 2, in the case of Cu coating, and Ni2Al3 and NiAl 3 when Ni-coated powders were infiltrated. The

    2. Radiation polymerizable coating composition containing an unsaturated phosphoric ester

      International Nuclear Information System (INIS)

      Dickie, R.A.; Cassatta, J.C.

      1976-01-01

      A radiation polymerizable protective coating composition or paint consists essentially of a binder solution of: (1) between about 90 and about 10 parts of a saturated, thermoplastic vinyl polymer prepared from at least about 85 weight percent of monofunctional vinyl monomers; (2) between about 10 and about 90 parts of vinyl solvent monomers for the vinyl polymer, at least about 10 weight percent, preferably at least about 30 weight percent, of the solvent monomers being selected from the group consisting of divinyl monomers, trivinyl monomers, tetravinyl monomers and mixtures of these; and (3) between about 1.0 and about 15.0 parts per 100 parts of the total of the thermoplastic vinyl polymer and the vinyl solvent monomers of a triester of phosphoric acid bearing one or more sites of vinyl unsaturation. The composition exhibits excellent quality and good adhesion to a variety of substrates, in particular metals, including vapor deposited metals. Preferred articles bearing such a coating are prepared by applying a base coat to a substrate and curing the same; vapor depositing a coating of metal over the surface of the base coat; and applying to and curing on the surface of the deposited metal the radiation polymerizable topcoat, preferably with little or no pigment contained therein. 7 claims, no drawings

    3. KARAKTERISASI KOMPOSIT EDIBLE FILM BUAH KOLANG-KALING (Arenge Pinnata DAN LILIN LEBAH (Beeswax [Characterization of Composite Edible Film Derived from Palm Fruit (Arenge pinnata and Beeswax

      Directory of Open Access Journals (Sweden)

      Budi Santoso

      2006-08-01

      Full Text Available The objective of this research was to study of the characteristics of edible film after addition of different concentrations of kolang-kaling and beeswax. The research used of Factorial Block Randomized Design with two treatments and each treatment was replicated three times. The first treatment was concentrations of the kolang-kaling (5%, 10%, 15% and 20%, and the second treatment was concentrations of the beeswax (0%, 0,5%, 1%, and 1,5%. The parameters were water content, tensile strength, elongation percentage, thickness, and water vapor transmission rate. The result showed that the addition of different concentrations of kolang-kaling and beeswax significantly afected the water content, tensile strength, elongation percentage, thickness, and water vapor transmission rate. The thickness increased with the increasing concentrations of kolang-kaling and beeswax. The water vapor transmission rate, tensile strength, and elongation percentage were decreased. The tensile strength, elongation percentage, thickness, and water vapor transmission rate of edible film were 0,342 Kgf cm-2, 52,5%, 0,025 mm and 53,439 gm-2hari-1 respectively. The best treatment was achived by using concentration of kolang-kaling at 5% and concentration of beeswax at 1,5%.

    4. SELF-ASSEMBLY CE OXIDE/ORGANOPOLYSILOXANE COMPOSITE COATINGS.

      Energy Technology Data Exchange (ETDEWEB)

      SUGAMA,T.; SABATINI,R.; GAWLIK,K.

      2005-01-01

      A self-assembly composite synthesis technology was used to put together a Ce(OH){sub 3}-dispersed poly-acetamide-acetoxyl methyl-propylsiloxane (PAAMPA) organometallic polymer. Three spontaneous reactions were involved; condensation, amidation, and acetoxylation, between the Ce acetate and aminopropylsilane triol (APST) at 150 C. An increase in temperature to 200 C led to the in-situ phase transformation of Ce(OH){sub 3} into Ce{sub 2}O{sub 3} in the PAAMPA matrix. A further increase to 250 C caused oxidative degradation of the PAAMPA, thereby generating copious fissures in the composite. We assessed the potential of Ce(OH){sub 3}/ and Ce{sub 2}O{sub 3}/ PAAMPA composite materials as corrosion-preventing coatings for carbon steel and aluminum. The Ce{sub 2}O{sub 3} composite coating displayed better performance in protecting both metals against NaCl-caused corrosion than did the Ce(OH){sub 3} composite. Using this coating formed at 200 C, we demonstrated that the following four factors played an essential role in further mitigating the corrosion of the metals: First was a minimum susceptibility of coating's surface to moisture; second was an enhanced densification of the coating layer; third was the retardation of the cathodic oxygen reduction reaction at the metal's corrosion sites due to the deposition of Ce{sub 2}O{sub 3} as a passive film over the metal's surface; and, fourth was its good adherence to metals. The last two factors contributed to minimizing the cathodic delamination of coating film from the metal's surface. We also noted that the affinity of the composite with the surface of aluminum was much stronger than that with steel. Correspondingly, the rate of corrosion of aluminum was reduced as much as two orders of magnitude by a nanoscale thick coating. In contrast, its ability to reduce the corrosion rate of steel was lower than one order of magnitude.

    5. Antibacterial silver nanocluster/silica composite coatings on stainless steel

      Energy Technology Data Exchange (ETDEWEB)

      Ferraris, M.; Perero, S. [Politecnico di Torino, Department of Applied Science and Technology, Torino, C.so Duca degli Abruzzi 24, I-10129 (Italy); Ferraris, S., E-mail: sara.ferraris@polito.it [Politecnico di Torino, Department of Applied Science and Technology, Torino, C.so Duca degli Abruzzi 24, I-10129 (Italy); Miola, M.; Vernè, E. [Politecnico di Torino, Department of Applied Science and Technology, Torino, C.so Duca degli Abruzzi 24, I-10129 (Italy); Skoglund, S. [KTH Royal Institute of Technology, Div. Surface and Corrosion Science, Dr. Kristinas v. 51, SE-100 44 (Sweden); Blomberg, E. [KTH Royal Institute of Technology, Div. Surface and Corrosion Science, Dr. Kristinas v. 51, SE-100 44 (Sweden); SP Technical Research Institute of Sweden, Chemistry, Materials and Surfaces, P.O. Box 5607, SE-114 86 Stockholm (Sweden); Odnevall Wallinder, I. [KTH Royal Institute of Technology, Div. Surface and Corrosion Science, Dr. Kristinas v. 51, SE-100 44 (Sweden)

      2017-02-28

      Highlights: • A silver nanocluster-silica composite coating sputter-deposited onto stainless steel. • Good adhesion and resistance upon cleaning with NaOH, H{sub 2}SO{sub 4} and detergents. • Low release of silver ions and no release as silver nanoparticles. • Good antibacterial activity against S. aureus even after heating to 450 °C. • Good antibacterial activity shown during cheese production. - Abstract: A coating made of silver nanocluster/silica composites has been deposited, via a radio frequency (RF) co-sputtering technique, for the first time onto stainless steel (AISI 304L) with the aim to improve its antibacterial properties. Different thermal treatments after coating deposition have been applied in order to optimize the coating adhesion, cohesion and its antibacterial properties. Its applicability has been investigated at realistic conditions in a cheese production plant. The physico-chemical characteristics of the coatings have been analyzed by means of different bulk and surface analytical techniques. Field emission scanning electron microscopy (FESEM), X-ray Photoelectron Spectroscopy (XPS), contact angle measurements and atomic force microscopy (AFM) were employed to assess coating morphology, composition, surface roughness, wetting properties, size and local distribution of the nanoparticles within the coating. Tape tests were used to determine the adhesion/cohesion properties of the coating. The amount and time-dependence of released silver in solutions of acetic acid, artificial water, artificial tap water and artificial milk were determined by means of Atomic Absorption Spectroscopy (AAS). The antibacterial effect of the coating was evaluated at different experimental conditions using a standard bacterial strain of Staphylococcus aureus in compliance with National Committee for Clinical Laboratory Standards (NCCLS) and AATCC 147 standards. The Ahearn test was performed to measure the adhesion of bacteria to the coated stainless steel

    6. Antibacterial silver nanocluster/silica composite coatings on stainless steel

      International Nuclear Information System (INIS)

      Ferraris, M.; Perero, S.; Ferraris, S.; Miola, M.; Vernè, E.; Skoglund, S.; Blomberg, E.; Odnevall Wallinder, I.

      2017-01-01

      Highlights: • A silver nanocluster-silica composite coating sputter-deposited onto stainless steel. • Good adhesion and resistance upon cleaning with NaOH, H_2SO_4 and detergents. • Low release of silver ions and no release as silver nanoparticles. • Good antibacterial activity against S. aureus even after heating to 450 °C. • Good antibacterial activity shown during cheese production. - Abstract: A coating made of silver nanocluster/silica composites has been deposited, via a radio frequency (RF) co-sputtering technique, for the first time onto stainless steel (AISI 304L) with the aim to improve its antibacterial properties. Different thermal treatments after coating deposition have been applied in order to optimize the coating adhesion, cohesion and its antibacterial properties. Its applicability has been investigated at realistic conditions in a cheese production plant. The physico-chemical characteristics of the coatings have been analyzed by means of different bulk and surface analytical techniques. Field emission scanning electron microscopy (FESEM), X-ray Photoelectron Spectroscopy (XPS), contact angle measurements and atomic force microscopy (AFM) were employed to assess coating morphology, composition, surface roughness, wetting properties, size and local distribution of the nanoparticles within the coating. Tape tests were used to determine the adhesion/cohesion properties of the coating. The amount and time-dependence of released silver in solutions of acetic acid, artificial water, artificial tap water and artificial milk were determined by means of Atomic Absorption Spectroscopy (AAS). The antibacterial effect of the coating was evaluated at different experimental conditions using a standard bacterial strain of Staphylococcus aureus in compliance with National Committee for Clinical Laboratory Standards (NCCLS) and AATCC 147 standards. The Ahearn test was performed to measure the adhesion of bacteria to the coated stainless steel surface

    7. Centesimal composition and physical-chemistry analysis of the edible mushroom Lentinus strigosus occurring in the Brazilian Amazon.

      Science.gov (United States)

      Sales-Campos, Ceci; Araujo, Lidia M; Minhoni, Marli T A; Andrade, Meire C N

      2013-01-01

      The centesimal composition and the physical and chemical analyses of Lentinus strigosus, an edible mushroom occurring in the Brazilian Amazon and produced in alternative substrates based on wood and agroindustrial residues, were evaluated. For this purpose, the C, N, pH, soluble solids, water activity, protein, lipids, total fiber, ash, carbohydrate, and energy levels were determined. The substrates were formulated from Simarouba amara Aubl. ("marupá"), Ochroma piramidale Cav. Ex. Lam. ("pau-de-balsa") and Anacardium giganteum ("cajuí") sawdust and Bactris gasipaes Kunth ("pupunheira") stipe and Saccharum officinarum (sugar cane bagasse). The results indicated that the nutritional composition of L. strigosus varied with the substrate of cultivation; the protein levels found in mushrooms grown in the different substrates (18-21.5%) varied with the substrate and was considered high; the soluble solids present in the mushrooms could have a relation with complex B hydrosoluble vitamins. L. strigosus could be considered as important food owing to its nutritional characteristics such as high protein content, metabolizable carbohydrates and fibers, and low lipids and calories content.

    8. Centesimal composition and physical-chemistry analysis of the edible mushroom Lentinus strigosus occurring in the Brazilian Amazon

      Directory of Open Access Journals (Sweden)

      CECI SALES-CAMPOS

      2013-10-01

      Full Text Available The centesimal composition and the physical and chemical analyses of Lentinus strigosus, an edible mushroom occurring in the Brazilian Amazon and produced in alternative substrates based on wood and agroindustrial residues, were evaluated. For this purpose, the C, N, pH, soluble solids, water activity, protein, lipids, total fiber, ash, carbohydrate, and energy levels were determined. The substrates were formulated from Simarouba amara Aubl. (“marupá”, Ochroma piramidale Cav. Ex. Lam. (“pau-de-balsa” and Anacardium giganteum (“cajuí” sawdust and Bactris gasipaes Kunth (“pupunheira” stipe and Saccharum officinarum (sugar cane bagasse. The results indicated that the nutritional composition of L. strigosus varied with the substrate of cultivation; the protein levels found in mushrooms grown in the different substrates (18 – 21.5% varied with the substrate and was considered high; the soluble solids present in the mushrooms could have a relation with complex B hydrosoluble vitamins. L. strigosus could be considered as important food owing to its nutritional characteristics such as high protein content, metabolizable carbohydrates and fibers, and low lipids and calories content.

    9. Structural ceramic coatings in composite microtruss cellular materials

      Energy Technology Data Exchange (ETDEWEB)

      Bele, E.; Bouwhuis, B.A.; Codd, C. [Department of Materials Science and Engineering, University of Toronto, 184 College Street, Toronto, Ontario (Canada); Hibbard, G.D., E-mail: glenn.hibbard@utoronto.ca [Department of Materials Science and Engineering, University of Toronto, 184 College Street, Toronto, Ontario (Canada)

      2011-09-15

      Graphical abstract: The compressive strength increase per unit sleeve thickness of Al cores reinforced with Al{sub 2}O{sub 3} sleeves is lower than the corresponding strength increase when the same cores are reinforced with nanocrystalline Ni (n-Ni) sleeves (left). However, because anodizing is a transformative surface treatment, the Al{sub 2}O{sub 3} coating was able to achieve this performance increase with little overall weight penalty (right). Display Omitted Highlights: {yields} A new type of metal/ceramic microtruss cellular composite has been created. {yields} Reinforcing sleeves of Al{sub 2}O{sub 3} were deposited on low density Al microtruss cores. {yields} Significant compressive strength increases were seen at virtually no weight penalty. {yields} Failure mechanisms were studied by electron microscopy and finite element analysis. {yields} Buckling, sleeve wrinkling, and coating fracture dictated the compressive strength. - Abstract: In the present study, anodizing was used to produce Al{sub 2}O{sub 3} coatings in a conventional 3003 aluminum alloy microtruss core; a 38.5 {mu}m thick anodic coating provided a 143% increase in compressive strength. Finite-element analyses were used to illustrate the dependence of the compressive strength and failure mechanism on the thickness of the anodic coating. At low thicknesses the microtruss strength is dictated by global bucking of the internal struts. However, at higher thicknesses the compressive strength is controlled by coating fracture and local deformation in the hinge region of the struts. Regardless of the failure mechanism, the compressive strength of the composite microtruss increased with increasing anodic coating thickness, with very little corresponding weight penalty.

    10. Structural ceramic coatings in composite microtruss cellular materials

      International Nuclear Information System (INIS)

      Bele, E.; Bouwhuis, B.A.; Codd, C.; Hibbard, G.D.

      2011-01-01

      Graphical abstract: The compressive strength increase per unit sleeve thickness of Al cores reinforced with Al 2 O 3 sleeves is lower than the corresponding strength increase when the same cores are reinforced with nanocrystalline Ni (n-Ni) sleeves (left). However, because anodizing is a transformative surface treatment, the Al 2 O 3 coating was able to achieve this performance increase with little overall weight penalty (right). Display Omitted Highlights: → A new type of metal/ceramic microtruss cellular composite has been created. → Reinforcing sleeves of Al 2 O 3 were deposited on low density Al microtruss cores. → Significant compressive strength increases were seen at virtually no weight penalty. → Failure mechanisms were studied by electron microscopy and finite element analysis. → Buckling, sleeve wrinkling, and coating fracture dictated the compressive strength. - Abstract: In the present study, anodizing was used to produce Al 2 O 3 coatings in a conventional 3003 aluminum alloy microtruss core; a 38.5 μm thick anodic coating provided a 143% increase in compressive strength. Finite-element analyses were used to illustrate the dependence of the compressive strength and failure mechanism on the thickness of the anodic coating. At low thicknesses the microtruss strength is dictated by global bucking of the internal struts. However, at higher thicknesses the compressive strength is controlled by coating fracture and local deformation in the hinge region of the struts. Regardless of the failure mechanism, the compressive strength of the composite microtruss increased with increasing anodic coating thickness, with very little corresponding weight penalty.

    11. Performance Evaluation of Refractory Composite Coatings in Potassium Rich Environment

      Directory of Open Access Journals (Sweden)

      Kristina BRINKIENĖ

      2016-09-01

      Full Text Available A laboratory scale method was used to study the performance of reinforced cement composites in potassium rich environment of biomass combustion. Buckwheat husk (BH was used as potential source of unexploited biomass product applicable as biomass derived fuel. In order to enhance the alkali effect on the properties of the investigated materials, the solution of potassium carbonate (K2CO3 was selected as potassium rich aggressive environment. Two reinforced cement composites as potential repair coatings for restoration of damaged refractory surfaces with different composition of aggregate were used in corrosion tests. Performance of refractory coatings was evaluated by analysing the microstructure of the treated composites as well as mechanical properties. Energy-dispersive X-ray spectroscopy (SEM/EDS and optical microscopy were used to study the microstructure in the corroded region of the refractory coatings. Long term studies in the solution of 1M K2CO3 for 56 months have demonstrated that composite with the additive of fluid cracking catalyst of oil refinery and petrochemical industries is more durable in the potassium rich environment.DOI: http://dx.doi.org/10.5755/j01.ms.22.3.8348

    12. Novel hybrid coatings with controlled wettability by composite nanoparticle aggregation

      Energy Technology Data Exchange (ETDEWEB)

      Hritcu, Doina, E-mail: dhritcu@ch.tuiasi.ro; Dodi, Gianina; Iordache, Mirabela L.; Draganescu, Dan; Sava, Elena; Popa, Marcel I.

      2016-11-30

      Highlights: • Magnetite-grafted chitosan composite nanoparticles were synthesized. • The particles are able to assemble under the influence of a silane derivative. • Thin films containing composites, chitosan and hydrolyzed silane were optimized. • The novel hybrid coatings show hierarchical roughness and high wetting angle. - Abstract: The aim of this study is to evaluate novel hybrid materials as potential candidates for producing coatings with hierarchical roughness and controlled wetting behaviour. Magnetite (Fe{sub 3}O{sub 4}) nanoparticles obtained by co-precipitation were embedded in matrices synthesized by radical graft co-polymerization of butyl acrylate (BA), butyl methacrylate (BMA), hexyl acrylate (HA) or styrene (ST) with ethylene glycol di-methacrylate (EGDMA) onto previously modified chitosan bearing surface vinyl groups. The resulting composite particles were characterized regarding their average size, composition and magnetic properties. Hybrid thin films containing suspension of composite particles in ethanol and pre-hydrolysed hexadecyltrimethoxysilane (HDTS) as a coupling/crosslinking agent were deposited by spin coating or spraying. The films were cured by heating and subsequently characterized regarding their morphology (scanning electron microscopy), contact angle with water and adhesion to substrate (scratch test). The structure-property relationship is discussed.

    13. THE STRUCTURE AND PROPERTIES OF COMPOSITE LASER CLAD COATINGS WITH Ni BASED MATRIX WITH WC PARTICLES

      Directory of Open Access Journals (Sweden)

      Zita Iždinská

      2010-09-01

      Full Text Available In this work, the influence of the processing conditions on the microstructure and abrasive wear behavior of composite laser clad coatings with Ni based matrix reinforced with 50% WC particles is analyzed. Composite powder was applied in the form of coatings onto a mild steel substrate (Fe–0.17% C by different laser powers and cladding speeds. The microstructure of the coatings was analyzed by scanning electron microscopy (SEM. Tribological properties of coatings were evaluated by pin-on-disc wear test. It appeared that the hardness of the matrix of composite coatings decreases with increasing cladding speed. However, wear resistance of composite coatings with decreasing hardness of Ni based matrix increases. Significantly enhanced wear resistance of WC composite coatings in comparison with Ni based coatings is attributed to the hard phase structures in composite coatings.

    14. Proximate compositions and bioactive compounds of edible wild and cultivated mushrooms from Northeast Thailand

      Directory of Open Access Journals (Sweden)

      Amporn Srikram

      2016-11-01

      Full Text Available Mushrooms are known as an excellent source of nutrients including macronutrients and bioactive compounds. Nutritional values were investigated involving proximate analysis, total antioxidant capacity (TAC, total phenol content (TPC and total flavonoid content (TFC of 10 edible wild mushroom species—Amanita calyptroderma Ark. et al., Amanita princeps Corner et Bas, A., Astraeus odoratus, Heimiella retispora (Pat. et. Bak. Boedijn., Mycoamaranthus cambodgensis (Pat. Trappe, Russula alboareolata Hongo, Russula cyanoxantha Schaeff.ex.Fr., Russula emetic (Schaeff. ex Fr. S.F.Gray., Russula virescens (Schaeff. fr., Termitomyces clypeatus Heim—and five cultivated mushroom species—Auricularia auricula-judae, Lentinus polychrous Lev., Lentinus squarrosulus Mont., Pleurotus sajor-caju (Fr. Sing, Volvariella vovacea (Bull. Ex.Fr. Sing. From the proximate analysis, the moisture contents of both wild and cultivated mushrooms ranged from 84.15% fresh weight (FW to 90.21% FW. The ash, crude protein, fat, crude fiber and carbohydrate contents of both wild and cultivated mushrooms were in the dry weight ranges 2.56–13.96%, 11.16–50.29%, 1.43–21.94%, 2.11–38.11% and 9.56–59.73%, respectively, and the contents of macronutrients in the mushrooms varied by variety. Wild mushrooms had a high fiber content compared to cultivated mushrooms. The contents of biologically active compounds of both wild and cultivated mushrooms also varied depending on the variety. Values for the TAC, TPC and TFC of wild mushrooms were higher than those of cultivated mushrooms. In conclusion, the proximate analysis for both wild and cultivated mushrooms was variety dependent and wild mushrooms contained a higher fiber content and more biologically active compounds than cultivated mushrooms.

    15. Flaxseed gum in combination with lemongrass essential oil as an effective edible coating for ready-to-eat pomegranate arils.

      Science.gov (United States)

      Yousuf, Basharat; Srivastava, Abhaya Kumar

      2017-11-01

      Flaxseed gum (FSG) in combination with lemongrass essential oil (LGEO) was investigated for coating of ready-to-eat pomegranate arils. FSG was used at 0.3% and 0.6% concentrations and with both concentrations LGEO was incorporated at levels of 0ppm, 200ppm, 500ppm and 800ppm. Changes in headspace gases, physicochemical, microbiological and sensory attributes of pomegranate arils stored at 5°C were studied on different days of analysis during the 12day storage period. Coatings containing LGEO were effective in reducing total plate count and yeast and mold populations. Increasing LGEO concentrations in the coatings resulted in more decline in microbial populations. Reduced weight loss occurred in coated samples as compared to uncoated (control) sample. Coated samples showed a gradual decrease in ripening index in contrast with control where a significantly higher decline was observed. Total soluble solids, pH and titratable acidity significantly varied over the storage period. Color change (ΔE) for control increased steeply over the storage time in comparison to coated samples. Furthermore, chroma decreased while as hue angle increased over time. Copyright © 2017 Elsevier B.V. All rights reserved.

    16. Thermal Protective Coating for High Temperature Polymer Composites

      Science.gov (United States)

      Barron, Andrew R.

      1999-01-01

      The central theme of this research is the application of carboxylate-alumoxane nanoparticles as precursors to thermally protective coatings for high temperature polymer composites. In addition, we will investigate the application of carboxylate-alumoxane nanoparticle as a component to polymer composites. The objective of this research was the high temperature protection of polymer composites via novel chemistry. The significance of this research is the development of a low cost and highly flexible synthetic methodology, with a compatible processing technique, for the fabrication of high temperature polymer composites. We proposed to accomplish this broad goal through the use of a class of ceramic precursor material, alumoxanes. Alumoxanes are nano-particles with a boehmite-like structure and an organic periphery. The technical goals of this program are to prepare and evaluate water soluble carboxylate-alumoxane for the preparation of ceramic coatings on polymer substrates. Our proposed approach is attractive since proof of concept has been demonstrated under the NRA 96-LeRC-1 Technology for Advanced High Temperature Gas Turbine Engines, HITEMP Program. For example, carbon and Kevlar(tm) fibers and matting have been successfully coated with ceramic thermally protective layers.

    17. THERMAL COMPOSITE COATINGS IMPROVING QUALITY OF TECHNICAL MEANS OF TRANSPORT

      Directory of Open Access Journals (Sweden)

      Andrzej POSMYK

      2015-06-01

      Full Text Available The paper presents the thermal properties of composite insulating material designed for producing of technical means of transport. This material can be coated on most of engineering materials. The matrix of this material is an acrylic resin ant non porous ceramic microspheres made of alumina are the reinforcing phase. Thanks to that into the spheres almost vacuum (0,13 Pa dominants and a big amount of spheres pro thickness unit is it possible to achieve low thermal conductivity. Usage of these coatings for producing of cooling cabins on vehicles let us to reduce of fuel for maintain of given temperature. Usage of these coatings in planes flying on high altitudes (temperature up to -60 allows to reduce of fuel consumption for heating. It has an important influence on transport quality and quality costs.

    18. Effects of Fiber Coating Composition on Mechanical Behavior of Silicon Carbide Fiber-Reinforced Celsian Composites

      Science.gov (United States)

      Bansal, Narottam P.; Elderidge, Jeffrey I.

      1998-01-01

      Celsian matrix composites reinforced with Hi-Nicalon fibers, precoated with a dual layer of BN/SiC by chemical vapor deposition in two separate batches, were fabricated. Mechanical properties of the composites were measured in three-point flexure. Despite supposedly identical processing, the composite panels fabricated with fibers coated in two batches exhibited substantially different mechanical behavior. The first matrix cracking stresses (sigma(sub mc)) of the composites reinforced with fibers coated in batch 1 and batch 2 were 436 and 122 MPa, respectively. This large difference in sigma(sub mc) was attributed to differences in fiber sliding stresses(tau(sub friction)), 121.2+/-48.7 and 10.4+/-3.1 MPa, respectively, for the two composites as determined by the fiber push-in method. Such a large difference in values of tau(sub friction) for the two composites was found to be due to the difference in the compositions of the interface coatings. Scanning Auger microprobe analysis revealed the presence of carbon layers between the fiber and BN, and also between the BN and SiC coatings in the composite showing lower tau(sub friction). This resulted in lower sigma(sub mc) in agreement with the ACK theory. The ultimate strengths of the two composites, 904 and 759 MPa, depended mainly on the fiber volume fraction and were not significantly effected by tau(sub friction) values, as expected. The poor reproducibility of the fiber coating composition between the two batches was judged to be the primary source of the large differences in performance of the two composites.

    19. Mechanical and Barrier Properties of Semi Refined Kappa Carrageenan-based Composite Edible Film and Its Application on Minimally Processed Chicken Breast Fillet

      Science.gov (United States)

      Praseptiangga, D.; Maimuni, B. H.; Manuhara, G. J.; Muhammad, D. R. A.

      2018-03-01

      Kappa-carrageenan (KC) is one of the most interesting biopolymers that is composed of a linear chain of sulfated galactans and extracted from red seaweed, Kappaphycus alvarezii. It shows good potential for development as a source of biodegradable or edible films. However, KC films do not have good water vapor barrier properties, as they are intrinsically hydrophilic. Palmitic acid (PA) as hydrophobic material was incorporated into semi-refined kappa-carrageenan (SRKC) edible films in order to improve water vapor barrier properties. In this study, composite films based on SRKC incorporating PA were prepared and their applications on minimally processed chicken breast fillet were evaluated. Composite SRKC-based films with varying concentrations of PA (5%, 10%, and 15% w/w) were obtained by a solvent casting method. Their mechanical and barrier properties were investigated. Results showed that the incorporation of PA in films caused an increase in thickness, but decrease in water vapor transmission rate (WVTR) as the concentration of PA increased (from 5% to 15% w/w). Composite SRKC-based edible film incorporating 15% w/w of PA presented better water vapor barrier properties as compared to other films with 5% and 10% w/w PA incorporation. Thus, formulation containing 15% w/w PA was used as a wrapping material for film application on minimally processed chicken breast fillet. The application results showed that the incorporation of PA in film caused an effect (p 0.05) change the color of minimally processed chicken breast fillet.

    20. High performance bio-based thermosets for composites and coatings

      Science.gov (United States)

      Paramarta, Adlina Ambeg

      In the recent decade, there has been increasing interest in using renewable feedstocks as chemical commodities for composites and coatings application. Vegetable oils are promising renewable resources due to their wide availability with affordable cost. In fact, the utilization of vegetable oils to produce composite and coatings products has been around for centuries; linseed oil was widely used for wide variety of paints. However, due to its chemical structure, the application of vegetable oils for high-performance materials is limited; and thus chemical modification is necessary. One of the modification approaches is by substituting the glycerol core in the triglycerides with sucrose to form sucrose esters of vegetable oil fatty acids, in which this resin possesses a higher number of functional group per molecule and a more rigid core. In this research, thermosets of highly functionalized sucrose esters of vegetable oils were developed. Two crosslinking methods of epoxidized surcrose soyate (ESS) resins were explored: direct polymerization with anhydride moieties for composite applications and Michael-addition reaction of acrylated-epoxidized sucrose soyate (AESS) for coatings applications. In the first project, it was shown that the reaction kinetics, thermal and mechanical properties of the materials can be tuned by varying the molar ratio between the epoxide and anhydride, plus the type and amount of catalyst. Furthermore, the toughness properties of the ESS-based thermosets can be improved by changing the type of anhydride crosslinkers and incorporating secondary phase rubbers. Then, in the second system, the epoxy functionality in the ESS was converted into acrylate group, which then crosslinked with amine groups through the Michael-addition reaction to produce coatings systems. The high number of functional groups and the fast reactivity of the crosslinker results in coatings that can be cured at ambient temperature, yet still possess moderately high glass

    1. Environmental Barrier Coatings for Ceramic Matrix Composites - An Overview

      Science.gov (United States)

      Lee, Kang; van Roode, Mark; Kashyap, Tania; Zhu, Dongming; Wiesner, Valerie

      2017-01-01

      SiC/SiC Ceramic Matrix Composites (CMCs) are increasingly being considered as structural materials for advanced power generation equipment because of their light weight, higher temperature capability, and oxidation resistance. Limitations of SiC/SiC CMCs include surface recession and component cracking and associated chemical changes in the CMC. The solutions pursued to improve the life of SiC/SiC CMCs include the incorporation of coating systems that provide surface protection, which has become known as an Environmental Barrier Coating (EBC). The development of EBCs for the protection of gas turbine hot section CMC components was a continuation of coating development work for corrosion protection of silicon-based monolithics. Work on EBC development for SiC/SiC CMCs has been ongoing at several national laboratories and the original gas turbine equipment manufacturers. The work includes extensive laboratory, rig and engine testing, including testing of EBC coated SiC/SiC CMCs in actual field applications. Another EBC degradation issue which is especially critical for CMC components used in aircraft engines is the degradation from glassy deposits of calcium-magnesium-aluminosilicate (CMAS) with other minor oxides. This paper addresses the need for and properties of external coatings on SiC/SiC CMCs to extend their useful life in service and the retention of their properties.

    2. Mechanical and tribological property of single layer graphene oxide reinforced titanium matrix composite coating

      Science.gov (United States)

      Hu, Zengrong; Li, Yue; Fan, Xueliang; Chen, Feng; Xu, Jiale

      2018-04-01

      Single layer grapheme oxide Nano sheets and Nano titanium powder were dispersed in deionized water by ultrasonic dispersion. Then the mixed solution was pre-coating on AISI4140 substrate. Using laser sintering process to fabricated grapheme oxide and Ti composite coating. Microstructures and composition of the composite coating was studied by Scanning Electron Microscopy (SEM), x-ray diffract meter (XRD) and Raman spectroscopy. Raman spectrum, XRD pattern and SEM results proved that grapheme oxide sheets were dispersed in the composite coating. The composite coating had much higher average Vickers hardness values than that of pure Ti coating. The tribological performance of the composite coatings became better while the suitable GO content was selected. For the 2.5wt. % GO content coating, the friction coefficient was reduced to near 0.1.

    3. Comprehensive review on application of edible film on meat and meat products: An eco-friendly approach.

      Science.gov (United States)

      Umaraw, Pramila; Verma, Akhilesh K

      2017-04-13

      The functions of packaging materials are to prevent moisture loss, drip, reduce lipid oxidation, improve some of their sensorial properties (color, taste and smell) and provide microbial stability of foods. Edible films can be made from protein, polysaccharides and lipids or by combination of any of these to form a composite film. Nanocomposites are composite films made by incorporation of nanoparticles. Edible packaging and coating of the meat and meat products enhances the self-life by the incorporation of the active compound (such as antimicrobial and antioxidant compound) in to the packaging matrix. Incorporation of the some ingredients in the matrix may also improve the nutritional as well as sensory attributes of the packed products. Edible packaging material also reduces environmental pollution by overcoming the burden degradation as edible films are biodegradable and thus eco-friendly.

    4. Effect of pectin edible coating enriched with essential oils of citrus on strawberry quality during refrigerated storage and shelf life

      Directory of Open Access Journals (Sweden)

      Soma Abdi

      2017-06-01

      Full Text Available Postharvest life of strawberry fruit is very short due to humidity and high metabolic activity. In order to extend the shelf life and quality of strawberry (cv. parous, effects of pectin coating enriched with different concentrations of lemon and orange peel essential oil were assessed at 20˚C for 6 days or 5˚C to 12 days. The experiment conducted based on a complete randomized design (CDR in 3 replications with 6 treatments including control (distilled water, pectin (1%, pectin enriched with orange peel essential oil (0.5 and 1% and pectin containing lemon peel essential oil (0.5 and 1%. Fruit quality was evaluated by marketing, weight loss, anthocyanin content, ascorbic acid content, total protein and chlorophyll of calyx every 3 days. Based on results coating fruits with citrus essential oil carried by pectin delayed the change in weight loss, total protein, anthocyanin content, maintained ascorbic acid content of fruits and also reduced chlorophyll destruction of calyx. The results showed that pectin coating containing lemon essential oil had a significant effect on the maintaining the visual quality of the fruit during the storage, delayed the weight loss and showed better results compared to the other coatings and to the control fruit. In addition, the maximum content of ascorbic acid and anthocyanin were obtained for strawberries coated with pectin containing lemon essential oil 1% after 12 days storage of fruits at 5˚C. All coatings significantly reduced weight loss of fresh strawberries during storage at 5˚C and 20˚C compared to the uncoated fruits. Results indicated that adding high concentrations (1% of orange peel essential oil into pectin coatings did not improve quality of fruits. In addition, it was found that adding orange peel essential oil to pectin coating accelerate decay of fruits. Based on results, pectin coating containing 1% lemon essential oil considered an appropriate treatment to improve shelf life and storage

    5. Measurement of residual stress in plasma-sprayed composite coatings with graded and uniform compositions

      Energy Technology Data Exchange (ETDEWEB)

      Kesler, O.; Suresh, S. [Massachusetts Inst. of Tech., Cambridge, MA (United States); Matejicek, J.; Sampath, S.

      1999-10-01

      Residual stresses in plasma sprayed composite coatings were studied experimentally by both curvature and neutron diffraction measurements. Graded and uniform composite coatings, consisting of nickel + alumina and NiCrAlY + yttria-stabilized zirconia, were investigated. This paper briefly summarizes our recent work dealing with the effects of coating thickness, composition, and material properties on the evolution of residual stresses in coatings. Analysis of the results allowed in some cases the separation of the quenching stress and thermal stress contributions to the final residual stress, as well as the determination of the through-thickness stress profile from measurements of different thickness specimens. In the ceramic-metal composites, it was found that the thermal mismatch stress plays a dominant role in the ceramic phase, whereas the stress in the metallic phase is mostly dominated by quenching stress. The residual stress measurement methods employed here were found to be complementary, in that each can provide unique information about the stress state. Through-thickness stress profiles in graded coatings were determined with high spatial resolution by the curvature method, and determination of the stress in each separate phase of a composite was made by neutron diffraction. (orig.) 14 refs.

    6. Metal matrix coated fiber composites and the methods of manufacturing such composites

      Science.gov (United States)

      Weeks, J.K. Jr.; Gensse, C.

      1993-09-14

      A fiber coating which allows ceramic or metal fibers to be wetted by molten metals is disclosed. The coating inhibits degradation of the physical properties caused by chemical reaction between the fiber and the coating itself or between the fiber and the metal matrix. The fiber coating preferably includes at least a wetting layer, and in some applications, a wetting layer and a barrier layer between the fiber and the wetting layer. The wetting layer promotes fiber wetting by the metal matrix. The barrier layer inhibits fiber degradation. The fiber coating permits the fibers to be infiltrated with the metal matrix resulting in composites having unique properties not obtainable in pure materials. 8 figures.

    7. Deposition of aluminum coatings on bio-composite laminates

      Science.gov (United States)

      Boccarusso, L.; Viscusi, A.; Durante, M.; Astarita, A.; De Fazio, D.; Sansone, R.; Caraviello, A.; Carrino, L.

      2018-05-01

      As a result of the increasing environmental awareness, the concern for environmental sustainability and the growing global waste problem, the interest of bio-composites materials is growing rapidly in the last years in order to use them in various engineering fields. Tremendous advantages and opportunities are associated with the use of these materials. On the other hand, some issues are related to the superficial properties of the bio-laminates, in particular the wear properties, the flame resistance and the aesthetic appearance have to be improved in order to extend the application fields of these materials. Aiming to these goals this paper deals with the study of the deposition of aluminum coating through cold spray process on hemp/PLA bio-composites manufactured by using the compression molding technique. Therefore, SEM observations, roughness analyses, bending tests, pin on disk and scratch tests were carried out in order to study the feasibility of the process and to investigate on the properties of the coated samples. The experimental results proved that when the process parameters of the deposition process are properly set, no damages are induced in the composite panel and that the aluminum coating, under specific load conditions, resulted to be able to protect the substrate.

    8. Effects of Bond Coating on NiCrBSi-Mo Composite Functional Coating Properties in Plasma Spraying NiCrBSi-Mo/Ni Coating

      OpenAIRE

      DU Ji-yu; LI Fang-yi; LU Hai-yang; SHANG Jian-tong; LI Zhen

      2017-01-01

      Nickel-based bond coating and composite functional coating were sprayed on leaf blade steel material FV520B successively by using air plasma spraying system. NiCrBSi-Mo powder deposition rate, coating porosity, bonding strength and surface hardness were tested. The results indicate that, for the NiCrBSi-Mo/Ni coating, bond coating with 180-220μm thickness can improve NiCrBSi-Mo powder deposition rate while the surface coating with lower porosity, higher bonding strength and high hardness is p...

    9. Engineered Polymer Composites Through Electrospun Nanofiber Coating of Fiber Tows

      Science.gov (United States)

      Kohlman, Lee W.; Bakis, Charles; Williams, Tiffany S.; Johnston, James C.; Kuczmarski, Maria A.; Roberts, Gary D.

      2014-01-01

      Composite materials offer significant weight savings in many aerospace applications. The toughness of the interface of fibers crossing at different angles often determines failure of composite components. A method for toughening the interface in fabric and filament wound components using directly electrospun thermoplastic nanofiber on carbon fiber tow is presented. The method was first demonstrated with limited trials, and then was scaled up to a continuous lab scale process. Filament wound tubes were fabricated and tested using unmodified baseline towpreg material and nanofiber coated towpreg.

    10. Electrochemical behavior of polypyrrole/chitosan composite coating on Ti metal for biomedical applications.

      Science.gov (United States)

      Rikhari, Bhavana; Pugal Mani, S; Rajendran, N

      2018-06-01

      In the present work, the corrosion resistance performance and biocompatibility of polypyrrole/chitosan (PPy/CHI) composite coated Ti was studied. The deposition of composite coating was carried out by electropolymerization method. The deposited PPy/CHI composite coatings were different in morphology, structural, surface roughness and wettability compared PPy coated Ti. The presence of composite coating was confirmed by solid 13 C NMR. The PPy/CHI composite coating showed enhanced microhardness and adhesion strength compared to the PPy coating. The corrosion protection ability of PPy/CHI composite coatings at various applied potentials was analyzed by dynamic electrochemical impedance spectroscopy (DEIS), exhibited higher impedance in all the potentials compared to uncoated and PPy coated Ti. The lower corrosion current density obtained for PPy/CHI-2 composite coating from polarization studies revealed increased corrosion protection ability in SBF solution. The stability of composite coating was confirmed by immersion studies. PPy/CHI-2 composite coating immersed in SBF solution enhances hydroxyapatite (HAp) formation. Copyright © 2018 Elsevier Ltd. All rights reserved.

    11. Impact of edible chitosan-cassava starch coatings enriched with Lippia gracilis Schauer genotype mixtures on the shelf life of guavas (Psidium guajava L.) during storage at room temperature.

      Science.gov (United States)

      de Aquino, Alana Bezerra; Blank, Arie Fitzgerald; Santana, Luciana Cristina Lins de Aquino

      2015-03-15

      The effect of edible chitosan-cassava starch (CH-CS) coatings containing a mixture of Lippia gracilis Schauer genotypes (EOM) on the shelf life of guavas during storage at room temperature for 10 days was studied. Sixteen formulations were prepared with a range of chitosan and essential oil mixtures concentrations, and the in vitro antimicrobial activity was tested. Formulations containing 2.0% cassava starch, 2.0% chitosan and 1.0%, 2.0% or 3.0% EOM were most effective in inhibiting the growth of the majority of bacteria. The edible CH-CS coating and CH-CS with 1.0% (CH-CS-EOM1) or 3.0% EOM (CH-CS-EOM3) were added to guavas and the shelf life was evaluated. On the tenth day of storage, total aerobic mesophilic bacteria and mould and yeast counts were statistically lower (p<0.05) in the CH-CS-EOM1- or CH-CS-EOM3-coated fruits than CH-CS-coated fruits. In addition, fruits coated with CH-CS or CH-CS-EOM showed no significant changes of total soluble solids content, while CH-CS-EOM-coated fruits showed lower titratable acidity than CH-CS-coated fruits at the end of storage. CH-CS-EOM3-coated guavas showed lower a(∗) and b(∗) values and higher L(∗) and hue values than those with other coatings. Copyright © 2014 Elsevier Ltd. All rights reserved.

    12. Spray-coating process in preparing PTFE-PPS composite super-hydrophobic coating

      Directory of Open Access Journals (Sweden)

      Rui Weng

      2014-03-01

      Full Text Available In order to improve the performance of a liquid-floated rotor micro-gyroscope, the resistance of the moving interface between the rotor and the floating liquid must be reduced. Hydrophobic treatment can reduce the frictional resistance between such interfaces, therefore we proposed a method to prepare a poly-tetrafluoroethylene (PTFE-poly-phenylene sulphide (PPS composite super-hydrophobic coating, based on a spraying process. This method can quickly prepare a continuous, uniform PTFE-PPS composite super-hydrophobic surface on a 2J85 material. This method can be divided into three steps, namely: pre-treatment; chemical etching; and spraying. The total time for this is around three hours. When the PTFE concentration is 4%, the average contact angle of the hydrophobic coating surface is 158°. If silicon dioxide nanoparticles are added, this can further improve the adhesion and mechanical strength of the super-hydrophobic composite coating. The maximum average contact angle can reach as high as 164° when the mass fraction of PTFE, PPS and silicon dioxide is 1:1:1.

    13. Spray-coating process in preparing PTFE-PPS composite super-hydrophobic coating

      Science.gov (United States)

      Weng, Rui; Zhang, Haifeng; Liu, Xiaowei

      2014-03-01

      In order to improve the performance of a liquid-floated rotor micro-gyroscope, the resistance of the moving interface between the rotor and the floating liquid must be reduced. Hydrophobic treatment can reduce the frictional resistance between such interfaces, therefore we proposed a method to prepare a poly-tetrafluoroethylene (PTFE)-poly-phenylene sulphide (PPS) composite super-hydrophobic coating, based on a spraying process. This method can quickly prepare a continuous, uniform PTFE-PPS composite super-hydrophobic surface on a 2J85 material. This method can be divided into three steps, namely: pre-treatment; chemical etching; and spraying. The total time for this is around three hours. When the PTFE concentration is 4%, the average contact angle of the hydrophobic coating surface is 158°. If silicon dioxide nanoparticles are added, this can further improve the adhesion and mechanical strength of the super-hydrophobic composite coating. The maximum average contact angle can reach as high as 164° when the mass fraction of PTFE, PPS and silicon dioxide is 1:1:1.

    14. Use of Plantago major seed mucilage as a novel edible coating incorporated with Anethum graveolens essential oil on shelf life extension of beef in refrigerated storage.

      Science.gov (United States)

      Behbahani, Behrooz Alizadeh; Shahidi, Fakhri; Yazdi, Farideh Tabatabaei; Mortazavi, Seyed Ali; Mohebbi, Mohebbat

      2017-01-01

      In this study, Plantago major seed mucilage (PMSM) was extracted from whole seeds using hot-water extraction (HWE). The dill (D) essential oil components were identified through gas chromatography (GC) and gas chromatography/mass spectrometry (GC/MS) and its antioxidant properties were examined through the methods of 2,2-diphenyl-1-picrylhydrazyl (DPPH), ferric reducing antioxidant potential (FRAP) and ß-carotene-linoleic acid assay (B-CL). Total phenolic content (TPC) was characterized through the Folin-Ciocalteu method and the antimicrobial effect was evaluated on 10 pathogenic microorganisms. PMSM edible coating incorporated were prepared in four different concentrations of essential oils, including 0, 0.5, 1 and 1.5% (w/w). The control and the coated beef samples were analyzed periodically for microbiological (total viable count, psychrotrophic count, Escherichia coli, Staphylococcus aureus and fungi), chemical (thiobarbituric acid, peroxide value and pH), and sensory characteristics. The IC 50 , FRAP, B-CL and TPC of the dill essential oil were equal to 11.44μg/ml, 9.45mmol/g, 82.86 and 162.65μg/ml GAE, respectively. PMSM extended the microbial shelf life of beef by 3days, whereas the PMSM+0.5%D, PMSM+1%D and PMSM+1.5%D resulted in a significant shelf life extension of the beef by 6, 9 and 9days, respectively, as compared to the control samples. Copyright © 2016 Elsevier B.V. All rights reserved.

    15. Nutrient composition of Dacryodes edulis seed and seed coat mixture

      Directory of Open Access Journals (Sweden)

      C.U. OGUNKA-NNOKA

      2017-07-01

      Full Text Available This study investigated the nutrient composition of D. edulis seed and seed coat mixture. Qualitative and quantitative phytochemicals, proximate, and vitamin compositions were evaluated using standard methods. Saponins were very high, alkaloids, flavonoids, and tannins were high, while terpenoids were low, and glycosides, aldehydes, and steroids were absent. The quantitative phytochemical determination followed the order; saponin > kaempferol > rutin > catechin > tannin > sapogenin > lunamarine > phenol > ribalinidine > anthocyanin > oxalate > phytate. For the proximate composition, carbohydrates had the highest concentration, followed by lipids and fibre, while, protein concentration was the lowest. Vitamin E (5.42 mg/100g, vitamin C (3.24 mg/100g, and vitamin A (2.84 mg/100g were the highest occurring constituent vitamins while vitamin B12 (0.035 mg/100g and vitamin B2 (0.075 mg/100g were the least occurring vitamins. This study has shown the rich phytochemical composition of D. edulis seed and seed coat mixture while showing deficiencies in proteins, distinct vitamins, and ash contents.

    16. Microbiological and biochemical characteristics of ground beef as affected by gamma irradiation, food additives and edible coating film

      Energy Technology Data Exchange (ETDEWEB)

      Ouattara, B.; Giroux, M.; Yefsah, R.; Smoragiewicz, W.; Saucier, L.; Borsa, J.; Lacroix, M. E-mail: monique.lacroix@inrs-iaf.uquebec.ca

      2002-03-01

      The current interest in 'minimally processed foods' has attracted the attention for combination of mild treatments to improve food safety and shelf-life extension. The present study was conducted to evaluate the combined effect of gamma irradiation and incorporation of naturally occurring antimicrobial compounds on microbial and biochemistry characteristics of ground beef. Ground beef patties (23% fat ) were purchased from a local grocery store (IGA, Laval, Que., Canada) and divided into 3 separate treatment groups: (i) control (ground beef without additive), (ii) ground beef with 0.5% (w/w) ascorbic acid, and (iii) ground beef with 0.5% ascorbic acid and coated with a protein-based coating containing selected spices. Samples were irradiated at 0, 1, 2, and 3 kGy final dose at the CIC. Samples were stored at 4 deg. C and evaluated periodically for microbial growth, total thiobarbituric reactive substances (TBARS) and free sulfydryl content. At the end of the storage period, Enterobacteriaceae, Lactic acid bacteria, Pseudomonas and Brochothrix thermosphacta were enumerated. Regardless of the treatment group, irradiation significantly (p{<=}0.05) reduced the total aerobic plate counts (APC). Irradiation doses of 1, 2, and 3 kGy produced immediate reduction of 2, 3, and 4 log units of APCs, respectively. Also, shelf-life periods were higher for ground beef samples containing food additives. Lactic acid bacteria and Brochothrix thermosphacta were more resistant to irradiation than Enterobacteriaceae and Pseudomonas. Concentration of TBARS and free sulfydryl concentrations were stabilized during post-irradiation storage for samples containing ascorbic acid and coated with the protein-based coating containing spices.

    17. Microbiological and biochemical characteristics of ground beef as affected by gamma irradiation, food additives and edible coating film

      International Nuclear Information System (INIS)

      Ouattara, B.; Giroux, M.; Yefsah, R.; Smoragiewicz, W.; Saucier, L.; Borsa, J.; Lacroix, M.

      2002-01-01

      The current interest in 'minimally processed foods' has attracted the attention for combination of mild treatments to improve food safety and shelf-life extension. The present study was conducted to evaluate the combined effect of gamma irradiation and incorporation of naturally occurring antimicrobial compounds on microbial and biochemistry characteristics of ground beef. Ground beef patties (23% fat ) were purchased from a local grocery store (IGA, Laval, Que., Canada) and divided into 3 separate treatment groups: (i) control (ground beef without additive), (ii) ground beef with 0.5% (w/w) ascorbic acid, and (iii) ground beef with 0.5% ascorbic acid and coated with a protein-based coating containing selected spices. Samples were irradiated at 0, 1, 2, and 3 kGy final dose at the CIC. Samples were stored at 4 deg. C and evaluated periodically for microbial growth, total thiobarbituric reactive substances (TBARS) and free sulfydryl content. At the end of the storage period, Enterobacteriaceae, Lactic acid bacteria, Pseudomonas and Brochothrix thermosphacta were enumerated. Regardless of the treatment group, irradiation significantly (p≤0.05) reduced the total aerobic plate counts (APC). Irradiation doses of 1, 2, and 3 kGy produced immediate reduction of 2, 3, and 4 log units of APCs, respectively. Also, shelf-life periods were higher for ground beef samples containing food additives. Lactic acid bacteria and Brochothrix thermosphacta were more resistant to irradiation than Enterobacteriaceae and Pseudomonas. Concentration of TBARS and free sulfydryl concentrations were stabilized during post-irradiation storage for samples containing ascorbic acid and coated with the protein-based coating containing spices

    18. Corrosion characterization of micro-arc oxidization composite electrophoretic coating on AZ31B magnesium alloy

      Energy Technology Data Exchange (ETDEWEB)

      Wang, Congjie [School of Materials Science and Engineering, Xi’an University of Technology, Xi’an 710048 (China); Jiang, Bailing [School of Materials Science and Engineering, Nanjing Tech University, Nanjing 211816 (China); Liu, Ming [General Motors China Science Lab, Shanghai 201206 (China); Ge, Yanfeng [School of Materials Science and Engineering, Xi’an University of Technology, Xi’an 710048 (China)

      2015-02-05

      Highlights: • A new protective composite coatings were prepared on AZ31B Mg alloy. • The E-coat locked into MAO coat by discharge channels forming a smoother and compact surface without defects. • Comparing with MAO coat, the MAOE composite coat could provide an excellent barrier for bare Mg against corrosion attack. - Abstract: A two layer composite coating system was applied on the surface of AZ31B magnesium alloy by Micro-arc Oxidation (MAO) plus electrophoretic coat (E-coat) technique. The Mg sample coated with MAO plus E-coat (MAOE) was compared with bare Mg and Mg sample coated by MAO only. The surface microstructure and cross section of bare and coated Mg before and after corrosion were examined by Scanning Electron Microscopy (SEM). The corrosion performance of bare and coated Mg was evaluated using electrochemical measurement and hydrogen evolution test. The results indicated that the corrosion resistance of AZ31B Mg alloy was significantly improved by MAOE composite coating. The corrosion mechanism of bare and coated Mg is discussed.

    19. Fabrication and characterization of SiC and ZrC composite coating on TRISO coated particle

      Energy Technology Data Exchange (ETDEWEB)

      Lee, H. G.; Lee, S. H.; Kim, D. J.; Park, J. Y.; Kim, W. J. [Korea Atomic Energy Research Institute, Daejeon (Korea, Republic of)

      2016-10-15

      SiC coating is widely suggested as structural materials for nuclear application due to its excellent high irradiation resistance properties and high temperature mechanical properties. SiC coating on TRistructural-ISOtropic (TRISO) coated fuel particles plays an important role as a protective layer from radioactive fission gas and a mechanical structural layer. TRISO coating layer was deposited on a spherical particle by a FBCVD method. The ZrO{sub 2} spherical particles were used as a simulant kernel. TRISO coating layers consisting of a porous buffer layer, an inner PyC layer were sequentially deposited before depositing SiC or ZrC coating layer. In order investigate the phase of each composite coating layer, Raman analysis was conducted. SiC, ZrC coating and SiC/ZrC composite coating on spherical particle were successfully deposited via FBCVD method by adjusting source gas flow rate. In the SiC and ZrC composite coating, SiC phase and ZrC phase were observed by XRD and SEM analysis. In the condition of 100 sccm of ZrCl{sub 4}, 25 sccm of CH{sub 4}, and 30 sccm of MTS, only two phases of SiC and ZrC were observed and two phases are located with clean grain boundary.

    20. Chemical composition and fatty acid profile of edible larva of Cirina ...

      African Journals Online (AJOL)

      The nutrient composition of the larva of Cirina forda (Westwood) was determined. It contained 33.12 (0.87 g/100g crude protein, 9.40 (0.16 g/100g crude fibre, 12.24 (18 g/ 100g fat, 7.12 ( 0.32 gl 100g ash, 38.12 (0.65 g/ 100g carbohydrate and gross energy value of 359 (2.83 Kcal/ 100g. The larva is an excellent source of ...

    1. Composite of ceramic-coated magnetic alloy particles

      Science.gov (United States)

      Moorhead, Arthur J.; Kim, Hyoun-Ee

      2000-01-01

      A composite structure and method for manufacturing same, the composite structure being comprised of metal particles and an inorganic bonding media. The method comprises the steps of coating particles of a metal powder with a thin layer of an inorganic bonding media selected from the group of powders consisting of a ceramic, glass, and glass-ceramic. The particles are assembled in a cavity and heat, with or without the addition of pressure, is thereafter applied to the particles until the layer of inorganic bonding media forms a strong bond with the particles and with the layer of inorganic bonding media on adjacent particles. The resulting composite structure is strong and remains cohesive at high temperatures.

    2. Low-Cost Repairable Oxidation Resistant Coatings for Carbon-Carbon Composites via CCVD

      National Research Council Canada - National Science Library

      Hendrick, Michelle

      2000-01-01

      ...) thin film process to yield oxidation resistant coatings on carbon-carbon (C-C) composites. Work was on simple coatings at this preliminary stage of investigation, including silicon dioxide, platinum and aluminum oxide...

    3. Seasonal variation in nutritional composition of Kappaphycus alvarezii (Doty) Doty-an edible seaweed.

      Science.gov (United States)

      Suresh Kumar, K; Ganesan, K; Subba Rao, P V

      2015-05-01

      Seasonal variation in the proximate and mineral composition of Kappaphycus alvarezii were investigated in the present study, moreover, the relationship between the nutritive components of this seaweed and the environment were also established. Carbohydrates represented the major portion of the algae (i.e. average total carbohydrate content was 23.01 ± 1.64 g/100 g DW), while the lipid content was the lowest among the constituents investigated (0.39 ± 0.04 to 0.91 ± 0.51 g/100 g DW). The protein content of K. alvarezii varied from 12.69 ± 0.6 to 23.61 ± 0.02 g/100 g DW, and the fiber content varied between 9.68 ± 0.08 to 18.57 ± 0.15 g/100 g DW. Highest total mineral content (29939.61 ± 9340.38 mg/100 g DW) was observed in April 2005, while least values were recorded in January 2006 i.e. (10997.62 ± 1120.26 mg/100 g DW). The Na/K ratio during the study ranged from 0.34 to 0.87. All the samples showed remarkable semi-refined carrageenan (SRC) yield ranging from 42.70 ± 1.07 to 63.73 ± 1.73 % (average 53.90 ± 1.37 %), and, the samples collected during December 2004 and January 2006 demonstrated maximum gel strengths i.e. 743 ± 15.28 and 783.33 ± 15.28 g·cm(-2) respectively. Various environmental parameters influenced the chemical composition of K. alvarezii, and these parameters demonstrated seasonal fluctuations. Moreover, based on the nutritional composition obtained, it could be stated that this seaweed has great scope to be incorporated into several food products as an excellent nutritional supplement, or as a value additive in animal or pet food.

    4. Nacre biomimetic design—A possible approach to prepare low infrared emissivity composite coatings

      International Nuclear Information System (INIS)

      Zhang, Weigang; Xu, Guoyue; Ding, Ruya; Duan, Kaige; Qiao, Jialiang

      2013-01-01

      Mimicking the highly organized brick-and-mortar structure of nacre, a kind of nacre-like organic–inorganic composite material of polyurethane (PU)/flaky bronze composite coatings with low infrared emissivity was successfully designed and prepared by using PU and flaky bronze powders as adhesives and pigments, respectively. The infrared emissivity and microstructure of the coatings were systematically investigated by infrared emissometer and scanning electron microscopy, respectively, and the cause of low infrared emissivity of the coatings was discussed by using the theories of one-dimensional photonic structure. The results show that the infrared emissivity of the nacre-like PU/flaky bronze composite coatings can be as low as 0.206 at the bronze content of 60 wt. %, and it is significantly lower than the value of PU/sphere bronze composite coatings. Microstructure observation illustrated that the nacre-like PU/flaky bronze composite coatings have similar one-dimensional photonic structural characteristics. The low infrared emissivity of PU/flaky bronze composite coatings is derived from the similar one-dimensional photonic structure in the coatings. Highlights: ► Nacre-like composite coatings with low infrared emissivity were prepared. ► Infrared emissivity of PU/flaky bronze composite coatings can be as low as 0.206. ► One-dimensional photonic structure is the cause for low emissivity of the coatings.

    5. Phase Stability and Thermal Conductivity of Composite Environmental Barrier Coatings on SiC/SiC Ceramic Matrix Composites

      Science.gov (United States)

      Benkel, Samantha; Zhu, Dongming

      2011-01-01

      Advanced environmental barrier coatings are being developed to protect SiC/SiC ceramic matrix composites in harsh combustion environments. The current coating development emphasis has been placed on the significantly improved cyclic durability and combustion environment stability in high-heat-flux and high velocity gas turbine engine environments. Environmental barrier coating systems based on hafnia (HfO2) and ytterbium silicate, HfO2-Si nano-composite bond coat systems have been processed and their stability and thermal conductivity behavior have been evaluated in simulated turbine environments. The incorporation of Silicon Carbide Nanotubes (SiCNT) into high stability (HfO2) and/or HfO2-silicon composite bond coats, along with ZrO2, HfO2 and rare earth silicate composite top coat systems, showed promise as excellent environmental barriers to protect the SiC/SiC ceramic matrix composites.

    6. Erosion resistance and adhesion of composite metal/ceramic coatings produced by plasma spraying

      OpenAIRE

      Ramm , D.; Hutchings , I.; Clyne , T.

      1993-01-01

      Ceramic coatings can exhibit greater erosion resistance than most metallic coatings. Such coatings are conveniently produced by thermal spraying. Unfortunately, thermally sprayed ceramic coatings often exhibit poor adhesion, partly as a consequence of the development of residual stresses during spraying and subsequent cooling. Composite coatings have been studied using aluminium/alumina deposits on steel substrates. The incorporation of ceramics within a ductile matrix has potential for sharp...

    7. Molybdate/phosphate composite conversion coating on magnesium alloy surface for corrosion protection

      International Nuclear Information System (INIS)

      Yong Zhiyi; Zhu Jin; Qiu Cheng; Liu Yali

      2008-01-01

      In this paper, a new conversion coating-molybdate/phosphate (Mo/P) coating on magnesium alloy was prepared and investigated by electrochemical impedance spectra (EIS), scanning electron microscope (SEM), X-ray photoelectron spectroscopy (XPS), X-ray diffraction (XRD) and salt-water immersion experiments, respectively. The results demonstrated that the Mo/P coating contained composite phases, which were consisted of metaphosphate as well as molybdate oxide with an 'alveolate-crystallized' structure. The composite Mo/P conversion coating had better corrosion resistance performance than molybdate (Mo) coating, and even had almost comparable corrosion protection for Mg alloy to the traditional chromate-based coating.

    8. Bioactive hydroxyapatite/graphene composite coating and its corrosion stability in simulated body fluid

      Energy Technology Data Exchange (ETDEWEB)

      Janković, Ana; Eraković, Sanja [Faculty of Technology and Metallurgy, University of Belgrade, Karnegijeva 4, 11 000 Belgrade (Serbia); Mitrić, Miodrag [Vinča Institute of Nuclear Sciences, University of Belgrade, Mike Petrovića Alasa 12-14, 11 000 Belgrade (Serbia); Matić, Ivana Z.; Juranić, Zorica D. [Institute of Oncology and Radiology of Serbia, Pasterova 14, 11 000 Belgrade (Serbia); Tsui, Gary C.P.; Tang, Chak-yin [Department of Industrial and Systems Engineering, The Hong Kong Polytechnic University, Hung Hom, Kowloon, Hong Kong (China); Mišković-Stanković, Vesna [Faculty of Technology and Metallurgy, University of Belgrade, Karnegijeva 4, 11 000 Belgrade (Serbia); Rhee, Kyong Yop, E-mail: rheeky@khu.ac.kr [Department of Mechanical Engineering, Kyung Hee University, Yongin 449-701 (Korea, Republic of); Park, Soo Jin [Chemistry, College of Natural Sciences, Inha University, Incheon 402-751 (Korea, Republic of)

      2015-03-05

      Highlights: • Bioactive HAP/Gr coating on Ti was successfully obtained by EPD. • Increased fracture toughness of the HAP/Gr coating compared to pure HAP coating. • HAP/Gr coating exhibited superior biomimetic mineralization vs. pure HAP coating. • Gr improved the mechanical properties and thermal stability of HAP/Gr coating. • HAP/Gr coating was classified as non-cytotoxic against the targeted PBMC. - Abstract: The hydroxyapatite/graphene (HAP/Gr) composite was electrodeposited on Ti using the electrophoretic deposition process to obtain uniform bioactive coating with improved mechanical strength and favorable corrosion stability in simulated body fluid (SBF). Incorporation of Gr was verified by Raman spectroscopy, X-ray diffraction, Fourier transform infrared spectroscopy, thermogravimetric analysis, and X-ray photoelectron analysis. The HAP/Gr composite coating exhibited reduced surface cracks, nearly double the hardness, and elastic modulus increased by almost 50% compared to pure HAP coating, as estimated by a nanoindentation test. The bioactive HAP/Gr composite coating provided a newly formed apatite layer in SBF with enhanced corrosion stability, as evidenced by electrochemical impedance spectroscopy. The thermal stability of the HAP/Gr coating was improved in comparison to the pure HAP coating, and the Ca/P ratio was closer to the stoichiometric value. No antibacterial activity against Staphylococcus aureus or Escherichia coli could be verified. The HAP/Gr composite coating was classified as non-cytotoxic when tested against healthy peripheral blood mononuclear cells (PBMC)

    9. Bioactive hydroxyapatite/graphene composite coating and its corrosion stability in simulated body fluid

      International Nuclear Information System (INIS)

      Janković, Ana; Eraković, Sanja; Mitrić, Miodrag; Matić, Ivana Z.; Juranić, Zorica D.; Tsui, Gary C.P.; Tang, Chak-yin; Mišković-Stanković, Vesna; Rhee, Kyong Yop; Park, Soo Jin

      2015-01-01

      Highlights: • Bioactive HAP/Gr coating on Ti was successfully obtained by EPD. • Increased fracture toughness of the HAP/Gr coating compared to pure HAP coating. • HAP/Gr coating exhibited superior biomimetic mineralization vs. pure HAP coating. • Gr improved the mechanical properties and thermal stability of HAP/Gr coating. • HAP/Gr coating was classified as non-cytotoxic against the targeted PBMC. - Abstract: The hydroxyapatite/graphene (HAP/Gr) composite was electrodeposited on Ti using the electrophoretic deposition process to obtain uniform bioactive coating with improved mechanical strength and favorable corrosion stability in simulated body fluid (SBF). Incorporation of Gr was verified by Raman spectroscopy, X-ray diffraction, Fourier transform infrared spectroscopy, thermogravimetric analysis, and X-ray photoelectron analysis. The HAP/Gr composite coating exhibited reduced surface cracks, nearly double the hardness, and elastic modulus increased by almost 50% compared to pure HAP coating, as estimated by a nanoindentation test. The bioactive HAP/Gr composite coating provided a newly formed apatite layer in SBF with enhanced corrosion stability, as evidenced by electrochemical impedance spectroscopy. The thermal stability of the HAP/Gr coating was improved in comparison to the pure HAP coating, and the Ca/P ratio was closer to the stoichiometric value. No antibacterial activity against Staphylococcus aureus or Escherichia coli could be verified. The HAP/Gr composite coating was classified as non-cytotoxic when tested against healthy peripheral blood mononuclear cells (PBMC)

    10. Antioxidants of Edible Mushrooms

      Directory of Open Access Journals (Sweden)

      Maja Kozarski

      2015-10-01

      Full Text Available Oxidative stress caused by an imbalanced metabolism and an excess of reactive oxygen species (ROS lead to a range of health disorders in humans. Our endogenous antioxidant defense mechanisms and our dietary intake of antioxidants potentially regulate our oxidative homeostasis. Numerous synthetic antioxidants can effectively improve defense mechanisms, but because of their adverse toxic effects under certain conditions, preference is given to natural compounds. Consequently, the requirements for natural, alternative sources of antioxidant foods identified in edible mushrooms, as well as the mechanistic action involved in their antioxidant properties, have increased rapidly. Chemical composition and antioxidant potential of mushrooms have been intensively studied. Edible mushrooms might be used directly in enhancement of antioxidant defenses through dietary supplementation to reduce the level of oxidative stress. Wild or cultivated, they have been related to significant antioxidant properties due to their bioactive compounds, such as polyphenols, polysaccharides, vitamins, carotenoids and minerals. Antioxidant and health benefits, observed in edible mushrooms, seem an additional reason for their traditional use as a popular delicacy food. This review discusses the consumption of edible mushrooms as a powerful instrument in maintaining health, longevity and life quality.

    11. Composition, phase behavior and thermal stability of natural edible fat from rambutan (Nephelium lappaceum L.) seed.

      Science.gov (United States)

      Solís-Fuentes, Julio A; Camey-Ortíz, Guadalupe; Hernández-Medel, María del Rosario; Pérez-Mendoza, Francisco; Durán-de-Bazúa, Carmen

      2010-01-01

      In this paper, the chemical composition, the main physicochemical properties, phase behavior and thermal stability of rambutan (Nephelium lappaceum L.) seed fat were studied. These results showed that the almond-like decorticated seed represents 6.1% of the wet weight fruit and is: 1.22% ash, 7.80% protein, 11.6% crude fiber, 46% carbohydrates, and 33.4% fat (d.b.). The main fatty acids in the drupe fat were 40.3% oleic, 34.5% arachidic, 6.1% palmitic, 7.1% stearic, 6.3% gondoic, and 2.9% behenic; the refraction, saponification and iodine values were 1.468, 186, and 47.0, respectively. The phase behavior analysis showed relatively simple crystallization and melting profiles: crystallization showed three well-differentiated groups of triglycerides around maximum peaks at +30.8, +15.6 and -18.1 degrees C; the fat-melting curve had a range between -14.5 and +51.8 degrees C with a fusion enthalpy of 124.3 J/g. The thermal stability analyzed in an inert atmosphere of N(2) and in a normal oxidizing atmosphere, showed that in the latter, fat decomposition begins at 237.3 degrees C and concludes at 529 degrees C, with three stages of decomposition. According to these results, rambutan seed fat has physicochemical and thermal characteristics that may become interesting for specific applications in several segments of the food industry.

    12. Paint Removal from Composites and Protective Coating Development

      Science.gov (United States)

      1991-01-01

      WL-TR-91-4025 AD-A249 238 PAINT REMOVAL FROM COMPOSITES AND PROTECTIVE COATING DEVELOPMENT Peter W. Kopf Jay Cheney John Martin, et al. Arthur D...PERSONAL AUTHOR(S) Peter Kopf, Jay Cheney, John Martin et al. 13a TYPE OF REPORT 13b. TIME COVERED 14. DATE OF REPORT (Year, Mot, Day) I1S. PAGE COUNT...Adhesive -.............. "𔃺*/900 -.... .... .... -- - 450 - - - -------- - -- e nk~ T17 J 50 ,1 ZEC 9837 Experimental 350OF Surfacing Film DESCRIPTION XHC

    13. Mechanical and thermal properties of water glass coated sisal fibre-reinforced polypropylene composite

      CSIR Research Space (South Africa)

      Phiri, G

      2012-10-01

      Full Text Available ?C). Figure 1 shows the processing steps followed to produce composite samples. Up to 15% fibre loading could be achieved and the sisal fibres were coated with water glass to improve fire resistance. In order to improve the adhesion between sisal... preparation process: (A) WG coated fibre, (B) High speed granulator, (C) Composite granules, (D) Single screw extruder, (E) Injection moulder and (F) Composite samples (dumbbells) Mechanical and thermal properties of water glass coated sisal fi bre...

    14. Process for a preparing a coating composition. [electrom irradiation

      Energy Technology Data Exchange (ETDEWEB)

      Kimura, T; Harada, H; Kobayashi, J; Nakamoto, H; Sunano, K

      1968-07-16

      An easily hardenable acrylic coating composition is prepared with low energy electron beams to develop a surface coating process without requiring solvents, and which may be widely applied by industry. The process comprises dissolving a polymer with a molecular weight in the 5,000 to 500,000 range in a monomer consisting of at least 30% by weight of acrylic monomer and 70% by weight of other vinyl monomers. The polymer is obtained by the polymerization of 1 to 40% by weight of vinyl monomer containing carboxyl radicals, 30 to 99% by weight of methacrylic monomer and 0 to 69% by weight of other copolymerizable vinyl monomers. Then, one mole of carboxyl radical of the solution reacts with 0.1 to 1.0 mole of vinyl monomer containing a glycidyl radical. In an embodiment, 17.5% by weight of methacrylate are dissolved in 82.5% of alkyl acrylate and undergo suspension polymerization in water in the presence of a catalyst to produce a beads-like polymer of molecular weight in the 5,000 to 500,000 range. Thereafter, 120 parts of the beads-like polymer are dissolved in 180 parts of acrylic monomer in the presence of a polymerization inhibitor. To this solution are added 22 parts of glycidyl methacrylate to react with carboxyl radicals, thereby obtaining non-solvent coating materials which contain the side chain vinyl radicals in the polymer. The acceleration voltage of the electron beams employed in the polymerization is generally 0.1 to 2.0 MeV. The dose rate to harden the coatings is in the range of 0.1 to 2.0 Mrad/sec.

    15. Study on the nano-composite electroless coating of Ni-P/Ag

      International Nuclear Information System (INIS)

      Ma Hongfang; Tian Fang; Li Dan; Guo Qiang

      2009-01-01

      The nano-composite coating of Ni-P/Ag was obtained by adding silver nanoparticles to the Ni-P electroless plating solutions. The properties of the coating were tested by scanning electron microscopy (SEM), energy dispersive spectrometry (EDS), differential scanning calorimeter (DSC), X-ray diffraction (XRD) and microsclerometer. Silver nanoparticles changed the properties of the composite coating. The Ni-P electroless coating contains 12.23 wt.% P while the composite coating of Ni-P/Ag contains 11.17 wt.% P and 0.24 wt.% Ag. The hardness of the composite coating is bigger than that of Ni-P alloy coating. Differential scanning calorimeter studies showed the amorphous to crystalline transition with precipitation of Ni 3 P and Ni around 335 deg. C

    16. Conservation of Williams pear using edible coating with alginate and carrageenan Conservação de pera Williams utilizando coberturas comestíveis compostas de alginato e carragena

      Directory of Open Access Journals (Sweden)

      Kessiane Silva de Moraes

      2012-12-01

      Full Text Available The aim of this study was to evaluate the physical and chemical parameters of Williams pear, stored at 25 ºC for 15 days, with and without edible coating. Edible coatings prepared with alginate 2% and carrageenan 0.5% were tested. The analyses carried out on the samples were: weight loss, pH, soluble solids, firmness, and color. The edible coatings were characterized in terms of mechanical properties, permeability, thickness, and opacity. The results show that the application of edible coatings with carrageenan and alginate in pears influenced physical and chemical characteristics such as weight loss, pH, total soluble solids, color, and firmness of the fruit. However, the alginate coating showed the best results on pear conservation since it had lower water vapor permeability and greater tensile strength, and therefore it can be used as a protective film on these fruits.O trabalho teve como objetivo avaliar os parâmetros físico-químicos da pera Williams, com e sem cobertura comestível, armazenada a 25 ºC por 15 dias. Foram testadas coberturas de alginato 2% e carragena 0,5%. As análises realizadas nas amostras foram: perda de massa fresca, pH, sólidos solúveis totais, firmeza e cor. As coberturas comestíveis foram caracterizadas por meio das propriedades mecânicas, de permeabilidade, espessura e opacidade. Os resultados mostraram que a aplicação de coberturas comestíveis com carragena e alginato em peras influenciou as características físico-químicas, como perda de massa fresca, pH, sólidos solúveis totais, cor e firmeza das frutas. Entretanto, a cobertura de alginato mostrou os melhores resultados na conservação de peras. Filmes de alginato apresentaram menor permeabilidade ao vapor de água e maior tensão de ruptura, servindo como uma barreira protetora à fruta.

    17. Tribological characteristics of electroless Ni–P–MoS2 composite coatings at elevated temperatures

      International Nuclear Information System (INIS)

      Li Zhen; Wang Jingbo; Lu Jinjun; Meng Junhu

      2013-01-01

      Highlights: ► Uniform Ni–P–MoS 2 composite coatings are deposited by electroless plating. ► Friction coefficient of composite coating decreases with the increase of temperature. ► Formation of lubricious oxide film leads to excellent tribological property. - Abstract: Ni–P–MoS 2 composite coatings were deposited on AISI-1045 steel plate by electroless plating followed by a heat treatment at 300 °C for 2 h. The high-temperature tribological characteristics of the composite coatings were evaluated under dry sliding conditions in a tribometer with ball-on-disk configuration. The effect of the co-deposition of MoS 2 on the friction and wear behaviors of composite coatings at elevated temperature was investigated. Scanning electron microscopy was used to determine the morphology of the worn surface of composite coating. The chemical states of some typical elements on the worn surfaces were determined by X-ray photoelectron spectroscope. The results indicate that friction coefficient of the composite coatings decreases with the increase of test temperature up to 500 °C, and the best tribological properties of Ni–P–MoS 2 composite coatings are achieved at 400 °C. The worn surface of Ni–P–MoS 2 composite coatings are characterized by mild scuffing and deformation. The improvement of tribological properties of the composite coatings was attributed to the formation of the lubricious oxide film composed of oxides of Ni and Mo at high temperatures. With the test temperature increasing to 600 °C, the tribological properties of the composite coating begin to deteriorate due to softening of the coating.

    18. High Temperature Dry Sliding Friction and Wear Performance of Laser Cladding WC/Ni Composite Coating

      Directory of Open Access Journals (Sweden)

      YANG Jiao-xi

      2016-06-01

      Full Text Available Two different types of agglomerate and angular WC/Ni matrix composite coatings were deposited by laser cladding. The high temperature wear resistance of these composite coatings was tested with a ring-on-disc MMG-10 apparatus. The morphologies of the worn surfaces were observed using a scanning electron microscopy (SEM equipped with an energy dispersive spectroscopy (EDS for elemental composition. The results show that the high temperature wear resistance of the laser clad WC/Ni-based composite coatings is improved significantly with WC mass fraction increasing. The 60% agglomerate WC/Ni composite coating has optimal high temperature wear resistance. High temperature wear mechanism of 60% WC/Ni composite coating is from abrasive wear of low temperature into composite function of the oxidation wear and abrasive wear.

    19. Improved Mechanical Compatibility and Cytocompatibility of Ta/Ti Double-Layered Composite Coating

      Science.gov (United States)

      Ding, Ding; Xie, Youtao; Li, Kai; Huang, Liping; Zheng, Xuebin

      2017-08-01

      In order to improve the mechanical compatibility and cytocompatibility of titanium implants, a composite coating with double layers composed of tantalum and titanium was designed and prepared using plasma spraying technology. In the composite coating, the upper tantalum layer provides a good biocompatibility, and the sublayer of titanium with a porous structure ensures the low elastic modulus. Results show that the fabricated composite coating exhibits a relatively low elastic modulus of 26.7 GPa, which is close to the elastic modulus of human cortical bone. In vitro cytocompatibility evaluation of the composite coating shows that the human bone marrow stromal cells exhibit enhanced adhesion and spreading performance on the double-layered composite coating in comparison with the single-layered titanium coating. In order to eliminate the misgivings of chemical stability of the composite coating in clinical application, electrochemical corrosion of the coating was examined. The results obtained revealed a very weak galvanic corrosion between the tantalum and titanium in the composite coating, which would ensure the safety of the coating in vivo.

    20. Laser cladding of Inconel 625-based composite coatings reinforced by porous chromium carbide particles

      Science.gov (United States)

      Janicki, Damian

      2017-09-01

      Inconel 625/Cr3C2 composite coatings were produced via a laser cladding process using Cr3C2 reinforcing particles presenting an open porosity of about 60%. A laser cladding system used consisted of a direct diode laser with a rectangular beam spot and the top-hat beam profile, and an off-axis powder injection nozzle. The microstructural characteristics of the coatings was investigated with the use of scanning electron microscopy and X-ray diffraction. A complete infiltration of the porous structure of Cr3C2 reinforcing particles and low degree of their dissolution have been achieved in a very narrow range of processing parameters. Crack-free composite coatings having a uniform distribution of the Cr3C2 particles and their fraction up to 36 vol% were produced. Comparative erosion tests between the Inconel 625/Cr3C2 composite coatings and the metallic Inconel 625 coatings were performed following the ASTM G 76 standard test method. It was found that the composite coatings have a significantly higher erosion resistance to that of metallic coatings for both 30° and 90° impingement angles. Additionally, the erosion performances of composite coatings were similar for both the normal and oblique impact conditions. The erosive wear behaviour of composite coatings is discussed and related to the unique microstructure of these coatings.

    1. Oxidation-resistant interface coatings for SiC/SiC composites

      Energy Technology Data Exchange (ETDEWEB)

      Stinton, D.P.; Kupp, E.R.; Hurley, J.W.; Lowden, R.A. [Oak Ridge National Lab., TN (United States)] [and others

      1996-08-01

      The characteristics of the fiber-matrix interfaces in ceramic matrix composites control the mechanical behavior of these composites. Finite element modeling (FEM) was performed to examine the effect of interface coating modulus and coefficient of thermal expansion on composite behavior. Oxide interface coatings (mullite and alumina-titania) produced by a sol-gel method were chosen for study as a result of the FEM results. Amorphous silicon carbide deposited by chemical vapor deposition (CVD) is also being investigated for interface coatings in SiC-matrix composites. Processing routes for depositing coatings of these materials were developed. Composites with these interfaces were produced and tested in flexure both as-processed and after oxidation to examine the suitability of these materials as interface coatings for SiC/SiC composites in fossil energy applications.

    2. Surfactant-free electrodeposition of reduced graphene oxide/copper composite coatings with enhanced wear resistance

      Science.gov (United States)

      Mai, Y. J.; Zhou, M. P.; Ling, H. J.; Chen, F. X.; Lian, W. Q.; Jie, X. H.

      2018-03-01

      How to uniformly disperse graphene sheets into the electrolyte is one of the main challenges to synthesize graphene enhanced nanocomposites by electrodeposition. A surfactant-free colloidal solution comprised of copper (II)-ethylene diamine tetra acetic acid ([CuIIEDTA]2-) complexes and graphene oxide (GO) sheets is proposed to electrodeposit reduced graphene oxide/copper (RGO/Cu) composite coatings. Anionic [CuIIEDTA]2- complexes stably coexist with negatively charged GO sheets due to the electrostatic repulsion between them, facilitating the electrochemical reduction and uniform dispersion of GO sheets into the copper matrix. The RGO/Cu composite coatings are well characterized by XRD, Raman, SEM and XPS. Their tribological behavior as a function of RGO content in composite coatings and normal loads are investigated. Also the chemical composition and topography of the wear tracks for the composite coatings are analyzed to deduce the lubricating and anti-wear mechanism of RGO/Cu composite coatings.

    3. New oxide-composite coatings for difficult metal-cutting tasks

      International Nuclear Information System (INIS)

      Westphal, H.; Berg, H. van den; Sottke, V.; Tabersky, R.

      2001-01-01

      The changes in today's metal working technology are driven by increasing cutting speeds, heavy/hard machining and an enormous amount by changes in work piece materials. These applications are asking for more tailor made cutting tool solutions. Together with the well established multi component coating technology a new approach of composite coatings is giving solutions for the tough demands of the cutting tool market. In this paper is presented composite coatings of AI 2 O 3 /ZrO-2/TiO x made by CVD. The coating is like high performance oxide ceramics for cutting applications. The coating is used in combination with MT CVD coatings and different carbide substrates. The CVD coating has optimum stress for cutting applications, low friction and very high thermal isolation. The outstanding performance of this coating is demonstrated in different applications. (author)

    4. Erosion resistance and adhesion of composite metal/ceramic coatings produced by plasma spraying

      International Nuclear Information System (INIS)

      Ramm, D.A.J.; Hutchings, I.M.; Clyne, T.W.

      1993-01-01

      Ceramic coatings can exhibit greater erosion resistance than most metallic coatings. Such coatings are conveniently produced by thermal spraying. Unfortunately, thermally sprayed ceramic coatings often exhibit poor adhesion, partly as a consequence of the development of residual stresses during spraying and subsequent cooling. Composite coatings have been studied using aluminium/alumina deposits on steel substrates. The incorporation of ceramics within a ductile matrix has potential for sharply reducing the erosive wear at high erodent impact angles, whilst retaining the good erosion resistance of ceramics at low angles. It is shown that the proportion of metal and ceramic at the free surface can be specified so as to optimise the erosion resistance. Experiments have also been carried out on the resistance of the coatings to debonding during four-point bending of the coated substrate. Progress is being made towards the tailoring of composition profiles in graded coatings so as to optimise the combination of erosion resistance and adhesion. (orig.)

    5. Formation of protective composite coatings with the use of SPTFE suspensions

      Science.gov (United States)

      Nadaraia, K. V.; Mashtalyar, D. V.; Sinebryukhov, S. L.; Gnedenkov, S. V.

      2017-09-01

      The method of protective composite coatings formation with the use of the plasma electrolytic oxidation (PEO) and subsequent treatment in isopropanol or aqueous suspension of the superdispersed polytetrafluoroethylene (SPTFE) have been developed. Morphological, electrochemical and tribological studies, as well as wetting ability of the protective coatings have been carried out. The obtained results corroborated the increase of the corrosion and wear resistance parameters for the polymer-containing coating in comparison with the base PEO-coating and uncoated material.

    6. A phenomenological model of coating/substrate adhesion and interfacial bimetallic peeling stress in composite mirrors

      Science.gov (United States)

      Mcelroy, Paul M.; Lawson, Daniel D.

      1990-01-01

      Adhesion and interfacial stress between metal films and structural composite material substrates is discussed. A theoretical and conceptual basis for selecting coating materials for composite mirror substrates is described. A phenomenological model that interrelates cohesive tensile strength of thin film coatings and interfacial peeling stresses is presented. The model serves as a basis in determining gradiated materials response and compatibility of composite substrate and coating combinations. Parametric evaluation of material properties and geometrical factors such as coating thickness are used to determine the threshold stress levels for maintaining adhesion at the different interfaces.

    7. Preparation and Electrochemical Properties of Graphene/Epoxy Resin Composite Coating

      Science.gov (United States)

      Liao, Zijun; Zhang, Tianchi; Qiao, Sen; Zhang, Luyihang

      2017-11-01

      The multilayer graphene powder as filler, epoxy modified silicone resin as film-forming agent, anticorrosion composite coating has been created using sand dispersion method, the electrochemical performance was compared with different content of graphene composite coating and pure epoxy resin coating. The open circuit potential (OCP), potentiodynamic polarization curves (Tafel Plot) and electrochemical impedance spectroscopy (EIS) were tested. The test results showed that the anti-corrosion performance of multilayer graphene added has improved greatly, and the content of the 5% best corrosion performance of graphene composite coating.

    8. Mechanical characterization of copper coated carbon nanotubes reinforced aluminum matrix composites

      International Nuclear Information System (INIS)

      Maqbool, Adnan; Hussain, M. Asif; Khalid, F. Ahmad; Bakhsh, Nabi; Hussain, Ali; Kim, Myong Ho

      2013-01-01

      In this investigation, carbon nanotube (CNT) reinforced aluminum composites were prepared by the molecular-level mixing process using copper coated CNTs. The mixing of CNTs was accomplished by ultrasonic mixing and ball milling. Electroless Cu-coated CNTs were used to enhance the interfacial bonding between CNTs and aluminum. Scanning electron microscope analysis revealed the homogenous dispersion of Cu-coated CNTs in the composite samples compared with the uncoated CNTs. The samples were pressureless sintered under vacuum followed by hot rolling to promote the uniform microstructure and dispersion of CNTs. In 1.0 wt.% uncoated and Cu-coated CNT/Al composites, compared to pure Al, the microhardness increased by 44% and 103%, respectively. As compared to the pure Al, for 1.0 wt.% uncoated CNT/Al composite, increase in yield strength and ultimate tensile strength was estimated about 58% and 62%, respectively. However, in case of 1.0 wt.% Cu-coated CNT/Al composite, yield strength and ultimate tensile strength were increased significantly about 121% and 107%, respectively. - Graphical Abstract: Copper coated CNTs were synthesized by the electroless plating process. Optimizing the plating bath to (1:1) by wt CNTs with Cu, thickness of Cu-coated CNTs has been reduced to 100 nm. Cu-coated CNTs developed the stronger interfacial bonding with the Al matrix which resulted in the efficient transfer of load. Highlights: • Copper coated CNTs were synthesized by the electroless plating process. • Thickness of Cu-coated CNTs has been reduced to 100 nm by optimized plating bath. • In 1.0 wt.% Cu-coated CNT/Al composite, microhardness increased by 103%. • Cu-coated CNTs transfer load efficiently with stronger interfacial bonding. • In 1.0 wt.% Cu-coated CNT/Al composite, Y.S and UTS increased by 126% and 105%

    9. An experimental study of the composite CNT/copper coating

      Science.gov (United States)

      Panarin, Valentin Ye.; Svavil‧nyi, Nikolai Ye.; Khominich, Anastasiya I.

      2018-03-01

      This paper presents experimental results on the preparation and investigation of the carbon nanotubes-copper composite material. Carbon nanotubes (CNTs) were synthesized on silicon substrates by the chemical vapor deposition (CVD) method and then filled with copper by evaporation from a melting pot in a vacuum. Copper evenly covered both the surface of the entangled tubes and the free substrate surface between the tubes. To improve the adhesion of tubes and matrix material, a carbon substructure was grown on the surface of tubes by adding working gas plasma to the CNT synthesis area. It is proposed to use a copper coating as a diffusion barrier upon subsequent filling of the reinforcing CNT frame by a carbide-forming materials matrix with predetermined physico-mechanical and tribological properties.

    10. Sol-gel coatings of ceramic fibres for composites with ceramic matrix

      International Nuclear Information System (INIS)

      Maier, B.; Grathwohl, G.; Spallek, M.; Pannhorst, W.

      1992-01-01

      The aim of this work was to show the feasibility in principle of sol-gel coating of ceramic reinforcement components for composites from technical aspects as well. The complexity of the coating task rises with the transition from individual fibres to bundles of fibres of different thickness to weaves, and finally to composites. (orig.) [de

    11. Thermal Performance Study of Composite Phase Change Material with Polyacrylicand Conformal Coating.

      Science.gov (United States)

      Kee, Shin Yiing; Munusamy, Yamuna; Ong, Kok Seng; Cornelis Metselaar, Hendrik Simon; Chee, Swee Yong; Lai, Koon Chun

      2017-07-28

      The composite PCM was prepared by blending polymethyl methacrylate (PMMA) and myristic acid (MA) in different weight percentages. The MA and PMMA were selected as PCM and supporting material, respectively. As liquid MA may leak out during the phase transition, this study proposes the use of two coatings, namely a polyacrylic coating and a conformal coating to overcome the leakage problem. Both coatings were studied in terms of the leakage test, chemical compatibility, thermal stability, morphology, and reliability. No leakage was found in the PCMs with coatings compared to those without under the same proportions of MA/PMMA, thus justifying the use of coatings in the present study. The chemically compatibility was confirmed by FTIR spectra: the functional groups of PCMs were in accordance with those of coatings. DSC showed that the coatings did not significantly change the melting and freezing temperatures, however, they improved the thermal stability of composite PCMs as seen in TGA analysis. Furthermore, the composite PCMs demonstrated good thermal reliability after 1000 times thermal cycling. The latent heat of melting reduced by only 0.16% and 1.02% for the PCMs coated with conformal coating and polyacrylic coating, respectively. Therefore, the proposed coatings can be considered in preparing fatty acid/PMMA blends attributed to the good stability, compatibility and leakage prevention.

    12. A novel biodegradable nicotinic acid/calcium phosphate composite coating on Mg-3Zn alloy

      Energy Technology Data Exchange (ETDEWEB)

      Song, Yingwei, E-mail: ywsong@imr.ac.cn; Shan, Dayong; Han, En-Hou

      2013-01-01

      A novel biodegradable composite coating is prepared to reduce the biodegradation rate of Mg-3Zn alloy. The Mg-3Zn substrate is first immersed into 0.02 mol L{sup -1} nicotinic acid (NA) solution, named as vitamin B{sub 3}, to obtain a pretreatment film, and then the electrodeposition of calcium phosphate coating with ultrasonic agitation is carried out on the NA pretreatment film to obtain a NA/calcium phosphate composite coating. Surface morphology is observed by scanning electron microscopy (SEM). Chemical composition is determined by X-ray diffraction (XRD) and EDX. Protection property of the coatings is evaluated by electrochemical tests. The biodegradable behavior is investigated by immersion tests. The results indicate that a thin but compact bottom layer can be obtained by NA pretreatment. The electrodeposition calcium phosphate coating consists of many flake particles and ultrasonic agitation can greatly improve the compactness of the coating. The composite coating is biodegradable and can reduce the biodegradation rate of Mg alloys in stimulated body fluid (SBF) for twenty times. The biodegradation process of the composite coating can be attributed to the gradual dissolution of the flake particles into chippings. - Highlights: Black-Right-Pointing-Pointer NA/calcium phosphate composite coating is prepared to protect Mg-3Zn alloy implant. Black-Right-Pointing-Pointer Nicotinic acid (vitamin B{sub 3}) is available to obtain a protective bottom film. Black-Right-Pointing-Pointer Ultrasonic agitation greatly improves the compactness of calcium phosphate coating. Black-Right-Pointing-Pointer The composite coating can reduce the biodegradation rate of Mg-3Zn twenty times. Black-Right-Pointing-Pointer The composite coating is biodegraded by the dissolution of flakes into chippings.

    13. Friction and wear behavior of nanosilica-filled epoxy resin composite coatings

      International Nuclear Information System (INIS)

      Kang Yingke; Chen Xinhua; Song Shiyong; Yu Laigui; Zhang Pingyu

      2012-01-01

      Hydrophilic silica nanoparticles (abridged as nano-SiO 2 ) surface-capped with epoxide were dispersed in the solution of epoxy resin (abridged as EP) in tetrahydrofuran under magnetic stirring. Resultant suspension of nano-SiO 2 in EP was then coated onto the surface of glass slides and dried at 80 °C in a vacuum oven for 2 h, generating epoxy resin-nanosilica composite coatings (coded as EP/nano-SiO 2 ). EP coating without nano-SiO 2 was also prepared as a reference in the same manner. A water contact angle meter and a surface profiler were separately performed to measure the water contact angles and surface roughness of as-prepared EP/nano-SiO 2 composite coatings. The friction and wear behavior of as-prepared EP/nano-SiO 2 composite coatings sliding against steel in a ball-on-plate contact configuration under unlubricated condition was evaluated. Particularly, the effect of coating composition on the friction and wear behavior of the composite coatings was highlighted in relation to their microstructure and worn surface morphology examined by means of scanning electron microscopy. Results indicate that EP/nano-SiO 2 composite coatings have a higher surface roughness and water contact angle than EP coating. The EP-SiO 2 coatings doped with a proper amount of hydrophilic SiO 2 nanoparticles show lower friction coefficient than EP coating. However, the introduction of surface-capped nanosilica as the filler results in inconsistent change in the friction coefficient and wear rate of the filled EP-matrix composites; and it needs further study to achieve well balanced friction-reducing and antiwear abilities of the composite coatings for tribological applications.

    14. Long-term antibiotic delivery by chitosan-based composite coatings with bone regenerative potential

      Science.gov (United States)

      Ordikhani, F.; Simchi, A.

      2014-10-01

      Composite coatings with bone-bioactivity and drug-eluting capacity are considered as promising materials for titanium bone implants. In this work, drug-eluting chitosan-bioactive glass coatings were fabricated by a single-step electrophoretic deposition technique. Drug-loading and -releasing capacity of the composite coatings were carried out using the vancomycin antibiotic. Uniform coatings with a thickness of ∼55 μm containing 23.7 wt% bioactive glass particles and various amounts of the antibiotic (380-630 μg/cm2) were produced. The coatings were bioactive in terms of apatite-forming ability in simulated body fluid and showed favorable cell adhesion and growth. In vitro biological tests also indicated that the composite coatings had better cellular affinity than pristine chitosan coatings. The in vitro elution kinetics of the composite coating revealed an initial burst release of around 40% of the drug within the first elution step of 1 h and following by a continuous eluting over 4 weeks, revealing long-term drug-delivering potential. Antibacterial tests using survival assay against Gram-positive Staphylococcus aureus bacteria determined the effect of vancomycin release on reduction of infection risk. Almost no bacteria were survived on the coatings prepared from the EPD suspension containing ≥0.5 g/l vancomycin. The developed chitosan-based composite coatings with bone bioactivity and long-term drug-delivery ability may be potentially useful for metallic implants to reduce infection risk.

    15. Process for producing a coating composition. [electron beam irradiation

      Energy Technology Data Exchange (ETDEWEB)

      Kimura, T; Harada, H; Kobayashi, S; Nakamoto, H; Sunano, K

      1968-07-19

      An easily hardenable acrylic coating composition is produced by irradiation with low energy electron beams to economize the industrial application of the composition. A polymer with molecular weights in the 5,000 to 500,000 range is composed of 1 to 40% by weight of a vinyl monomer containing a glycidyl radical, 30 to 99% of a methacrylic monomer and 0 to 69% of other copolymerizable vinyl monomers. This polymer dissolves in a monomer containing at least 30% of an acrylic monomer and 70% of other vinyl monomers. The reaction takes place between 0.1 to 1.0 mole of vinyl monomer containing a carboxyl radical and one mole of glycidyl radical in the solution. In an embodiment, 17.5% by weight of glycidyl methacrylate and 82.5% of alkyl acrylate are polymerized in suspension in the presence of a catalyst to form a bead like polymer with molecular weights in the 5,000 to 500,000 range. After 120 parts of the bead like polymer are dissolved in 180 parts of the acrylic monomer in the presence of a polymerization inhibitor by heating, 22 parts of ..cap alpha.., ..beta..- unsaturated monocarboxylic acid are added to the solution to react with the glycidyl radical, whereby a non-solvent type coating material containing the polymer having a vinyl radical side chain is produced. In the place of the catalyst, electron beams can be used at an energy level of 0.1 to 20 MeV. The dose rate may be in the range of 0.1 to 2.0 Mrad/sec.

    16. Composition Effects on Aluminide Oxidation Performance: Objectives for Improved Bond Coats

      International Nuclear Information System (INIS)

      Pint, BA

      2001-01-01

      Formerly, the role of metallic coatings on Ni-base superalloys was simply to limit environmental attack of the underlying substrate. However, a new paradigm has been established for metallic coatings adapted as bond coats for thermal barrier coatings. It is no longer sufficient for the coating to just minimize the corrosion rate. The metallic coating must also form a slow-growing external Al(sub 2)O(sub 3) layer beneath the overlying low thermal conductivity ceramic top coat. This thermally grown oxide or scale must have near-perfect adhesion in order to limit spallation of the top coat, thereby achieving a long coating lifetime. While oxidation is not the only concern in complex thermal barrier coating systems, it is, however, a primary factor in developing the next generation of bond coats. Therefore, a set of compositional guidelines for coatings is proposed in order to maximize oxidation performance. These criteria are based on test results of cast alloy compositions to quantify an d understand possible improvements as a basis for further investigations using coatings made by chemical vapor deposited (CVD). Experimental work includes furnace cycle testing and in-depth characterization of the alumina scale, including transmission electron microscopy (TEM)

    17. Preparation and characterization of graphite-dispersed styrene-acrylic emulsion composite coating on magnesium alloy

      Energy Technology Data Exchange (ETDEWEB)

      Zhang Renhui [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Science, Lanzhou 730000 (China); Lanzhou University of Technology, College of Science, Lanzhou 730050 (China); Liang Jun, E-mail: jliang@licp.cas.cn [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Science, Lanzhou 730000 (China); Wang Qing [Lanzhou University of Technology, College of Science, Lanzhou 730050 (China)

      2012-03-01

      In this work, an electrically conductive, corrosion resistant graphite-dispersed styrene-acrylic emulsion composite coating on AZ91D magnesium alloy was successfully produced by the method of anodic deposition. The microstructure, composition and conductivity of the composite coating were characterized using optical microscope (OM), scanning electron microscope (SEM), X-ray diffraction (XRD), Fourier transform infrared spectrometer (FTIR) and four electrode volume resistivity instrument, respectively. The corrosion resistance of the coating was evaluated using potentiodynamic polarization measurements and salt spray tests. It is found that the graphite-dispersed styrene-acrylic emulsion composite coating was layered structure and displayed good electrical conductivity. The potentiodynamic polarization tests and salt spray tests reveal that the composite coating was successful in providing superior corrosion resistance to AZ91D magnesium alloy.

    18. A novel silica nanotube reinforced ionic incorporated hydroxyapatite composite coating on polypyrrole coated 316L SS for implant application

      Energy Technology Data Exchange (ETDEWEB)

      Prem Ananth, K., E-mail: kpananth01@gmail.com [Department of Nanoscience and Technology, Bharathiar University, Coimbatore – 641 046 (India); Joseph Nathanael, A. [Department of Nano, Medical and Polymer Materials, Yeungnam University, Gyeongsan 712-749 (Korea, Republic of); Jose, Sujin P. [Department of Materials Science and Nano engineering, Rice University, Texas 77005 (United States); School of Physics, Madurai Kamaraj University, Madurai-625021 (India); Oh, Tae Hwan [Department of Nano, Medical and Polymer Materials, Yeungnam University, Gyeongsan 712-749 (Korea, Republic of); Mangalaraj, D. [Department of Nanoscience and Technology, Bharathiar University, Coimbatore – 641 046 (India)

      2016-02-01

      An attempt has been made to deposit a novel smart ion (Sr, Zn, Mg) substituted hydroxyapatite (I-HAp) and silica nanotube (SiNTs) composite coatings on polypyrrole (PPy) coated surgical grade 316L stainless steel (316L SS) to improve its biocompatibility and corrosion resistance. The I-HAp/SiNTS/PPy bilayer coating on 316L SS was prepared by electrophoretic deposition technique. Potentiodynamic polarization and electrochemical impedance spectroscopy (EIS) studies were carried out. These results confirmed the significant improvement of the corrosion resistance of the 316L SS alloy by the I-HAp/SiNTs/PPy bilayer composite coating. The adhesion strength and hardness test confirmed the anticipated mechanical properties of the composite. A low contact angle value revealed the hydrophilic nature. Inductively coupled plasma-atomic emission spectroscopy (ICP-AES) was used for the leach out analysis of the samples. Added to this, the bioactivity of the composite was analyzed by observing the apatite formation in the SBF solution for 7, 14, 21 and 28 days of incubation. An enhancement of in vitro osteoblast attachment and cell viability was observed, which could lead to the optimistic orthopedic and dental applications. - Highlights: • Polypyrrole (PPy) coated 316L SS substrates were fabricated using electrodeposition method. • A novel silica nanotube (SiNTs) and ionic substituted (Sr, Zn, Mg) hydroxyapatite composite (I-HAp) were prepared. • The composite (I-HAp/SiNTs) was coated on PPy coated 316L SS substrate using electrophoretic deposition. • These results are favorable for corrosion resistance and enhanced osteoblast cell attachment for bone formation.

    19. Electrochemically assisted co-deposition of calcium phosphate/collagen coatings on carbon/carbon composites

      Energy Technology Data Exchange (ETDEWEB)

      Zhao Xueni [C/C Composites Technology Research Center, State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi' an, Shaanxi 710072 (China); Hu Tao [C/C Composites Technology Research Center, State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi' an, Shaanxi 710072 (China); Department of Cardiology, Xijing Hospital, Fourth Military Medical University, Xi' an, Shaanxi 710032 (China); Li Hejun, E-mail: lihejun@nwpu.edu.cn [C/C Composites Technology Research Center, State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi' an, Shaanxi 710072 (China); Chen Mengdi; Cao Sheng; Zhang Leilei [C/C Composites Technology Research Center, State Key Laboratory of Solidification Processing, Northwestern Polytechnical University, Xi' an, Shaanxi 710072 (China); Hou Xianghui [Department of Mechanical, Materials and Manufacturing Engineering, University of Nottingham, University Park, Nottingham NG7 2RD (United Kingdom)

      2011-02-01

      Calcium phosphate (CaP)/collagen coatings were prepared on the surface of carbon/carbon (C/C) composites by electrochemically assisted co-deposition technique. The effects of collagen concentration in the electrolyte on morphology, structure and composition of the coatings were systematically investigated using scanning electron microscopy (SEM), X-ray diffraction (XRD), Fourier transformed infrared (FTIR) spectroscopy and X-ray photoelectron spectroscopy (XPS). The adhesive strength of the coatings was also evaluated by scratch tests and tensile bond tests. It was demonstrated that the coatings of three-dimensional collagen network structure was formed on the C/C composites from the electrolyte containing collagen. The surface of the collagen network was covered by uniform CaP aggregates. The coatings were actually composites of CaP and collagen. Hydroxyapatite (HA) was a favorable composition in the coatings with the increase of the collagen concentration in the electrolyte. The formed collagen network increased the cohesive and adhesive strength of the coatings. The adhesive strength between the coatings and substrates increased as the collagen concentration in the electrolyte increased. The coatings prepared at the collagen concentration of 500 mg/L in the electrolyte were not scraped off until the applied load reached 32.0 {+-} 2.2 N and the average tensile adhesive strength of the coatings was 4.83 {+-} 0.71 MPa. After C/C coated with composite coatings (500 mg/L) being immersed in a 10{sup -3} M Ca (OH){sub 2} solution at 30-33 deg. C for 96 h, nano-structured HA/collagen coatings similar to the natural human bone were obtained on the C/C.

    20. Effect of Graphene Coating on the Heat Transfer Performance of a Composite Anti-/Deicing Component

      Directory of Open Access Journals (Sweden)

      Long Chen

      2017-09-01

      Full Text Available The thermal conductivity of a graphene coating for anti-/deicing is rarely studied. This paper presents an improved anti-/deicing efficiency method for composite material anti-/deicing by using the heat-transfer characteristic of a graphene coating. An anti-/deicing experiment was conducted using the centrifugal force generated by a helicopter rotor. Results showed that the graphene coating can accelerate the internal heat transfer of the composite material, thereby improving the anti-icing and deicing efficiency of the helicopter rotor. The spraying process parameters, such as coating thickness and spraying pressure, were also studied. Results showed that reducing coating thickness and increasing spraying pressure are beneficial in preparing a graphene coating with high thermal conductivity. This study provides an experimental reference for the application of a graphene coating in anti-/deicing.

    1. Synthesis and electrochemical properties of composite galvanic Ni with carbon nanomaterials and PVD Mo coatings

      International Nuclear Information System (INIS)

      Drozdovich, V.B.; Chayeuski, V.V.; Zhdanok, S.A.; Barkovskaya, M.M.

      2011-01-01

      Double layer coatings Ni – Mo were obtained by electrolytic deposition of galvanic Ni and following arc PVD deposition of molybdenum. The ion plating coatings Mo on Ni foil and composition electrolytic Ni coatings with carbon nanomaterials (CNM) deposited on mild steel has been also investigated. Composite galvanic Ni coatings with CNM and ion plating coatings Mo contain separately obtained cubic α-Mo phase as well as fragmentary solid solution Mo in Ni. Such coatings exclude hydrogenation of Ni foundation in alkaline solution and possess enlarged electrocatalytic properties while emitting hydrogen and oxygen. Availability of carbon based nanomaterials in combined coatings is cause of an active absorption hydrogen after cathodic polarization. A formation on the surface layer of nanostructure solid solution (Ni, Mo) after compression plasma flows treatment with fixed parameters of patterns Mo/Ni/ mild steel take place. (authors)

    2. Microstructures and tribological properties of laser cladded Ti-based metallic glass composite coatings

      International Nuclear Information System (INIS)

      Lan, Xiaodong; Wu, Hong; Liu, Yong; Zhang, Weidong; Li, Ruidi; Chen, Shiqi; Zai, Xiongfei; Hu, Te

      2016-01-01

      Metallic glass composite coatings Ti 45 Cu 41 Ni 9 Zr 5 and Ti 45 Cu 41 Ni 6 Zr 5 Sn 3 (at.%) on a Ti-30Nb-5Ta-7Zr (wt.%) (TNTZ) alloy were prepared by laser cladding. The microstructures of the coatings were characterized by means of X-ray diffractometry (XRD), scanning electron microscopy (SEM) equipped with energy dispersive X-ray analyzer (EDXA), and transmission electron microscopy (TEM). Results indicated that the coatings have an amorphous structure embedded with a few nanocrystalline phases and dendrites. A partial substitution of Ni by Sn can improve the glass forming ability of Ti-base metallic glass system, and induce the formation of nano-sized Ni 2 SnTi phase during the cyclic laser heating. The tribological behavior of both the substrate and the coatings was investigated in detail. A significant improvement in both the hardness and the wear resistance of the coatings was achieved with the addition of Sn. The relationship between the wear resistance and the microstructures of the coatings was discussed. - Highlights: •Ti-based metallic glass composite coatings were prepared by laser cladding. •The wear resistance is greatly improved by laser cladding of composite coatings. •Substitution of Ni by Sn increases GFA and wear resistance of the coatings. •A good balance of crystalline/amorphous phases improves the wear resistance. •Adhesive wear serves as the dominant wear mechanism of the composite coatings.

    3. Effect of applied voltage on phase components of composite coatings prepared by micro-arc oxidation

      Energy Technology Data Exchange (ETDEWEB)

      Zhu, Wenjun [Department of Prosthodontics, Guanghua School of Stomatology, Sun Yat-sen University, Guangzhou 510055 (China); Fang, Yu-Jing [Department of Colorectal Surgery, State Key Laboratory of Oncology in South China, Sun Yat-sen University Cancer Center, Guangzhou 510060 (China); Zheng, Huade [College of Materials Science and Engineering, South China University of Technology, Guangzhou 510641 (China); Tan, Guoxin [Guangdong University of Technology, Guangdong Province 510006 (China); Cheng, Haimei [College of Materials Science and Engineering, South China University of Technology, Guangzhou 510641 (China); Ning, Chengyun, E-mail: imcyning@scut.edu.cn [College of Materials Science and Engineering, South China University of Technology, Guangzhou 510641 (China)

      2013-10-01

      In this report, we present results from our experiments on composite coatings formed on biomedical titanium substrates by micro-arc oxidation (MAO) in constant-voltage mode. The coatings were prepared on the substrates in an aqueous electrolyte containing calcium acetate and β-glycerol phosphate disodium salt pentahydrate (β-GP). We analyzed the element distribution and phase components of the coatings prepared at different voltages by X-ray diffraction, thin-coating X-ray diffraction, electron-probe microanalysis, and Fourier-transform infrared spectroscopy. The results show that the composite coatings formed at 500 V consist of titania (TiO{sub 2}), hydroxylapatite (HA), and calcium carbonate (CaCO{sub 3}). Furthermore, the concentration of Ca, P, and Ti gradually changes with increasing applied voltage, and the phase components of the composite coatings gradually change from the bottom of the coating to the top: the bottom layer consists of TiO{sub 2}, the middle layer consists of TiO{sub 2} and HA, and the top layer consists of HA and a small amount of CaCO{sub 3}. The formation of HA directly on the coating surface by MAO technique can greatly enhance the surface bioactivity. - Highlights: • Coatings prepared on biomedical titanium substrate by micro-arc oxidation • Coatings composed of titania, hydroxyapatite and calcium carbonate • Hydroxyapatite on the coating surface can enhance the surface bioactivity.

    4. Preparation and Properties of Microarc Oxidation Self-Lubricating Composite Coatings on Aluminum Alloy

      Directory of Open Access Journals (Sweden)

      Zhenwei Li

      2017-04-01

      Full Text Available Microarc oxidation (MAO coatings were prepared on 2024-T4 aluminum alloy using pulsed bipolar power supply at different cathode current densities. The MAO ceramic coatings contained many crater-like micropores and a small number of microcracks. After the MAO coatings were formed, the coated samples were immersed into a water-based Polytetrafluoroethylene (PTFE dispersion. The micropores and microcracks on the surface of the MAO coatings were filled with PTFE dispersion for preparing MAO self-lubricating composite coatings. The microstructure and properties of MAO coatings and the wear resistance of microarc oxidation self-lubricating composite coatings were analyzed by SEM, laser confocal microscope, X-ray diffractometry (XRD, Vickers hardness test, scratch test and ball-on-disc abrasive tests, respectively. The results revealed that the wear rates of the MAO coatings decreased significantly with an increase in cathode current density. Compared to the MAO coatings, the microarc oxidation self-lubricating composite coatings exhibited a lower friction coefficient and lower wear rates.

    5. High-temperature protective coatings for C/SiC composites

      Directory of Open Access Journals (Sweden)

      Xiang Yang

      2014-12-01

      Full Text Available Carbon fiber-reinforced silicon carbide (C/SiC composites were well-established light weight materials combining high specific strength and damage tolerance. For high-temperature applications, protective coatings had to provide oxidation and corrosion resistance. The literature data introduced various technologies and materials, which were suitable for the application of coatings. Coating procedures and conditions, materials design limitations related to the reactivity of the components of C/SiC composites, new approaches and coating systems to the selection of protective coatings materials were examined. The focus of future work was on optimization by further multilayer coating systems and the anti-oxidation ability of C/SiC composites at temperatures up to 2073 K or higher in water vapor.

    6. Enhanced corrosion protective PANI-PAA/PEI multilayer composite coatings for 316SS by spin coating technique

      Energy Technology Data Exchange (ETDEWEB)

      Syed, Junaid Ali; Lu, Hongbin; Tang, Shaochun; Meng, Xiangkang, E-mail: mengxk@nju.edu.cn

      2015-01-15

      Highlights: • PANI-PAA/PEI multilayers with controllable thickness were fabricated by spin assembly. • PAA matrix results in the homogeneous dispersion of PANI in the composite coatings. • Spin coating combined with heating assures the linear increase in thickness with n. • The corrosion protection property of PANI-PAA/PEI coatings were optimized at n = 20. • Enhanced protection owing to multilayer structure that lengthens the diffusion pathway of ions. - Abstract: In the present study, polyaniline-polyacrylic acid/polyethyleneimine (PANI-PAA/PEI) composite coatings with a multilayer structure for corrosion protection of 316 stainless steels (316SS) were prepared by an alternate deposition. Spin coating combined with heating assists removal of residual water that result in a linear increase in thickness with layer number (n). The combination of PANI-PAA composite with PEI and their multilayer structure provides a synergistic enhancement of corrosion resistance properties as determined by electrochemical measurements in 3.5% NaCl solution. Importantly, the PANI-PAA/PEI coating with an optimized layer number of n = 20 shows improved corrosion protection. The superior performance was attributed to the formation of an interfacial oxide layer as well as the multilayer structure that extend the diffusion pathway of corrosive ions.

    7. Multilayer composition coatings for cutting tools: formation and performance properties

      Science.gov (United States)

      Tabakov, Vladimir P.; Vereschaka, Anatoly S.; Vereschaka, Alexey A.

      2018-03-01

      The paper considers the concept of a multi-layer architecture of the coating in which each layer has a predetermined functionality. Latest generation of coatings with multi-layered architecture for cutting tools secure a dual nature of the coating, in which coatings should not only improve the mechanical and physical characteristics of the cutting tool material, but also reduce the thermo-mechanical effect on the cutting tool determining wear intensity. Here are presented the results of the development of combined methods of forming multi-layer coatings with improved properties. Combined method of forming coatings using a pulsed laser allowed reducing excessively high levels of compressive residual stress and increasing micro hardness of the multilayered coatings. The results in testing coated HSS tools showed that the use of additional pulse of laser processing increases tool life up to 3 times. Using filtered cathodic vacuum arc deposition for the generation of multilayer coatings based on TiAlN compound has increased the wear-resistance of carbide tools by 2 fold compared with tool life of cutting tool with commercial TiN coatings. The aim of this study was to develop an innovative methodological approach to the deposition of multilayer coatings for cutting tools with functional architectural selection, properties and parameters of the coating based on sound knowledge of coating failure in machining process.

    8. Mechanical, degradation and cytocompatibility properties of magnesium coated phosphate glass fibre reinforced polycaprolactone composites.

      Science.gov (United States)

      Liu, Xiaoling; Hasan, Muhammad S; Grant, David M; Harper, Lee T; Parsons, Andrew J; Palmer, Graham; Rudd, Chris D; Ahmed, Ifty

      2014-11-01

      Retention of mechanical properties of phosphate glass fibre reinforced degradable polyesters such as polycaprolactone and polylactic acid in aqueous media has been shown to be strongly influenced by the integrity of the fibre/polymer interface. A previous study utilising 'single fibre' fragmentation tests found that coating with magnesium improved the fibre and matrix interfacial shear strength. Therefore, the aim of this study was to investigate the effects of a magnesium coating on the manufacture and characterisation of a random chopped fibre reinforced polycaprolactone composite. Short chopped strand non-woven phosphate glass fibre mats were sputter coated with degradable magnesium to manufacture phosphate glass fibre/polycaprolactone composites. The degradation behaviour (water uptake, mass loss and pH change of the media) of these polycaprolactone composites as well as of pure polycaprolactone was investigated in phosphate buffered saline. The Mg coated fibre reinforced composites revealed less water uptake and mass loss during degradation compared to the non-coated composites. The cations released were also explored and a lower ion release profile for all three cations investigated (namely Na(+), Mg(2+) and Ca(2+)) was seen for the Mg coated composite samples. An increase of 17% in tensile strength and 47% in tensile modulus was obtained for the Mg coated composite samples. Both flexural and tensile properties were investigated and a higher retention of mechanical properties was obtained for the Mg coated fibre reinforced composite samples up to 10 days immersion in PBS. Cytocompatibility study showed both composite samples (coated and non-coated) had good cytocompatibility with human osteosarcoma cell line. © The Author(s) 2014 Reprints and permissions: sagepub.co.uk/journalsPermissions.nav.

    9. Viability of oxide fiber coatings in ceramic composites for accommodation of misfit stresses

      International Nuclear Information System (INIS)

      Kerans, R.J.

      1996-01-01

      The C and BN fiber coatings used in most ceramic composites perform a less obvious but equally essential function, in addition to crack deflection; they accommodate misfit stresses due to interfacial fracture surface roughness. Coatings substituted for them must also perform that function to be effective. However, in general, oxides are much less compliant materials than C and BN, which raises the question of the feasibility of oxide substitutes. The viability of oxide coatings for accommodating misfit stresses in Nicalon fiber/SiC composites was investigated by calculating the maximum misfit stresses as functions of coating properties and geometries. Control of interfacial fracture path was also briefly considered. The implications regarding composite properties were examined by calculating properties for composites with mechanically viable oxide coatings

    10. Effective response of nonlinear cylindrical coated composites under external AC and DC electric field

      International Nuclear Information System (INIS)

      Yu-Yan, Shen; Xiao-Gang, Chen; Wei, Cui; Yan-Hua, Hao; Qian-Qian, Li

      2009-01-01

      This paper uses the perturbation method to study effective response of nonlinear cylindrical coated composites. Under the external AC and DC electric field E a (1 + sin ωt), the local potentials of composites at all harmonic frequencies are induced. An effective nonlinear response to composite is given for the cylindrical coated inclusions in the dilute limit. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

    11. Erosion protection of carbon-epoxy composites by plasma-sprayed coatings

      International Nuclear Information System (INIS)

      Alonso, F.; Fagoaga, I.; Oregui, P.

      1991-01-01

      This paper deals with the production of plasma-sprayed erosion-resistant coatings on carbon-fibre - epoxy composites, and the study of their erosion behaviour. The heat sensitivity of the composite substrate requires a specific spraying procedure in order to avoid its degradation. In addition, several bonding layers were studied to allow spraying of the protective coatings. Two different functional coatings were sprayed onto an aluminium-glass bonding layer, a WC-12Co cermet and an Al 2 O 3 ceramic oxide. The microstructure and properties of these coatings were studied and their erosion behaviour determined experimentally in an erosion-testing device. (orig.)

    12. Tribological properties of copper-based composites with copper coated NbSe2 and CNT

      International Nuclear Information System (INIS)

      Chen, Beibei; Yang, Jin; Zhang, Qing; Huang, Hong; Li, Hongping; Tang, Hua; Li, Changsheng

      2015-01-01

      Graphical abstract: Morphology of copper coated NbSe 2 and CNT; friction coefficient and wear rate of copper-based composites. - Highlights: • NbSe 2 and CNT were coated with copper layers by the means of electroless plating. • The mechanical and tribological properties of copper composites were studied. • The enhancement mechanisms of copper coated NbSe 2 and CNT were proposed. • Copper–copper coated (12 wt.%NbSe 2 –3 wt.%CNT) composite had the best wear resistance. - Abstract: Copper-based composites with copper coated NbSe 2 and/or CNT were fabricated by the powder metallurgy technique. The morphology and phase composition of copper coated NbSe 2 and carbon nanotube (CNT) were observed using high solution transmission electronic microscope (HRTEM), scanning electronic microscope (SEM equipped with EDS) and X-ray diffraction (XRD). The density, hardness, and bending strength of as-prepared copper-based composites were measured, and their tribological properties were investigated using UMT-2 tester. Results indicated that all copper-based composites showed decreased density and bending strength, but increased hardness in comparison with copper matrix. Besides, the incorporation of copper coated NbSe 2 improved the friction-reducing and anti-wear properties of copper matrix. Addition of copper coated CNT greatly enhanced the mechanical and tribological properties. In particular, when the content of copper coated CNT was 3 wt.%, the corresponding composite exhibited the best tribological properties. This was because NbSe 2 was distributed chaotically in matrix, which greatly improved the friction-reducing property of copper, while CNT with superior mechanical strength enhanced the wear resistance by increasing the load-carrying capacity. More importantly, copper layers coated on NbSe 2 and CNT favored the good interfacial combination between fillers and copper matrix showing beneficial effect for the stresses transferring from matrix to fillers

    13. Electrodeposition, characterization, and antibacterial activity of zinc/silver particle composite coatings

      Energy Technology Data Exchange (ETDEWEB)

      Reyes-Vidal, Y.; Suarez-Rojas, R.; Ruiz, C.; Torres, J. [Center of Research and Technological Development in Electrochemistry (CIDETEQ), Parque Tecnológico Sanfandila, Pedro Escobedo, Querétaro, A.P.064, C.P.76703, Querétaro (Mexico); Ţălu, Ştefan [Technical University of Cluj-Napoca, Faculty of Mechanical Engineering, Department of AET, Discipline of Descriptive Geometry and Engineering Graphics, 103-105 B-dul Muncii St., Cluj-Napoca 400641 Cluj (Romania); Méndez, Alia [Centro de Química-ICUAP Benemérita Universidad Autónoma de Puebla, Ciudad Universitaria Puebla, 72530 Puebla (Mexico); Trejo, G., E-mail: gtrejo@cideteq.mx [Center of Research and Technological Development in Electrochemistry (CIDETEQ), Parque Tecnológico Sanfandila, Pedro Escobedo, Querétaro, A.P.064, C.P.76703, Querétaro (Mexico)

      2015-07-01

      Highlights: • Zn/AgPs composites coatings were formed for electrodeposition. • CTAB promotes occlusion of silver particles in the coating. • Zn/AgPs coatings present very good antibacterial activity. - Abstract: Composite coatings consisting of zinc and silver particles (Zn/AgPs) with antibacterial activity were prepared using an electrodeposition technique. The morphology, composition, and structure of the Zn/AgPs composite coatings were analyzed using scanning electron microscopy (SEM) coupled with energy-dispersive spectroscopy (EDS), inductively coupled plasma (ICP) spectrometry, and X-ray diffraction (XRD). The antibacterial properties of the coatings against the microorganisms Escherichia coli as a model Gram-negative bacterium and Staphylococcus aureus as a model Gram-positive bacterium were studied quantitatively and qualitatively. The results revealed that the dispersant cetyltrimethylammonium bromide (CTAB) assisted in the formation of a stable suspension of Ag particles in the electrolytic bath for 24 h. Likewise, a high concentration of CTAB in the electrolytic bath promoted an increase in the number of Ag particles occluded in the Zn/AgPs coatings. The Zn/AgPs coatings that were obtained were compact, smooth, and shiny materials. Antimicrobial tests performed on the Zn/AgPs coatings revealed that the inhibition of bacterial growth after 30 min of contact time was between 91% and 98% when the AgPs content ranged from 4.3 to 14.0 mg cm{sup −3}.

    14. Electrodeposition of Copper/Carbonous Nanomaterial Composite Coatings for Heat-Dissipation Materials

      Directory of Open Access Journals (Sweden)

      Yasuki Goto

      2017-12-01

      Full Text Available Carbonous nanomaterials are promising additives for composite coatings for heat-dissipation materials because of their excellent thermal conductivity. Here, copper/carbonous nanomaterial composite coatings were prepared using nanodiamond (ND as the carbonous nanomaterial. The copper/ND composite coatings were electrically deposited onto copper substrates from a continuously stirred copper sulfate coating bath containing NDs. NDs were dispersed by ultrasonic treatment, and the initial bath pH was adjusted by adding sodium hydroxide solution or sulfuric acid solution before electrodeposition. The effects of various coating conditions—the initial ND concentration, initial bath pH, stirring speed, electrical current density, and the amount of electricity—on the ND content of the coatings were investigated. Furthermore, the surface of the NDs was modified by hydrothermal treatment to improve ND incorporation. A higher initial ND concentration and a higher stirring speed increased the ND content of the coatings, whereas a higher initial bath pH and a greater amount of electricity decreased it. The electrical current density showed a minimum ND content at approximately 5 A/dm2. Hydrothermal treatment, which introduced carboxyl groups onto the ND surface, improved the ND content of the coatings. A copper/ND composite coating with a maximum of 3.85 wt % ND was obtained.

    15. Wear Resistance Properties Reinforcement Using Nano-Al/Cu Composite Coating in Sliding Bearing Maintenance.

      Science.gov (United States)

      Liu, Hongtao; Li, Zhixiong; Wang, Jianmei; Sheng, Chenxing; Liu, Wanli

      2018-03-01

      Sliding bearing maintenance is crucial for reducing the cost and extending the service life. An efficient and practical solution is to coat a restorative agent onto the worn/damaged bearings. Traditional pure-copper (Cu) coating results in a soft surface and poor abrasion resistance. To address this issue, this paper presents a nano-composite repairing coating method. A series of nano-Al/Cu coatings were prepared on the surface of 45 steel by composite electro-brush plating (EBP). Their micro-hardness was examined by a MHV-2000 Vickers hardness tester, and tribological properties by a UMT-2M Micro-friction tester, 3D profiler and SEM. Then, the influence of processing parameters such as nano-particle concentration and coating thickness on the micro-hardness of nano-Al/Cu coating was analyzed. The experimental analysis results demonstrate that, when the nano-Al particle concentration in electrolyte was 10 g/L, the micro-hardness of the composite coating was 1.1 times as much as that of pure-Cu coating. When the Al nano-particle concentration in electrolyte was 20 g/L, the micro-hardness of the composite coating reached its maximum value (i.e., 231.6 HV). Compared with the pure-Cu coating, the hardness and wear resistance of the nano-composite coating were increased, and the friction coefficient and wear volume were decreased, because of the grain strengthening and dispersion strengthening. The development in this work may provide a feasible and effective nano-composite EBP method for sliding bearing repair.

    16. FeCoNi coated glass fibers in composite sheets for electromagnetic absorption and shielding behaviors

      Science.gov (United States)

      Lee, Joonsik; Jung, Byung Mun; Lee, Sang Bok; Lee, Sang Kwan; Kim, Ki Hyeon

      2017-09-01

      To evaluate the electromagnetic (EM) absorption and shield of magnetic composite sheet, we prepared the FeCoNi coated glass fibers filled in composite sheet. The FeCoNi was coated by electroless plating on glass fiber as a filler. The coated FeCoNi found that consist of mixtures of bcc and fcc phase. The magnetization and coercivity of coated FeCoNi are about 110 emu/g and 57 Oe, respectively. The permittivity and permeability of the FeCoNi composite sheet were about 21 and 1, respectively. Power absorption increased 95% with the increment of frequency up to 10 GHz. Inter-decoupling of this composite sheet showed maximum 30 dB at around 5.3 GHz, which is comparable to that of a conductive Cu foil. Shielding effectiveness (SE) was measured by using rectangular waveguide method. SE of composite obtained about 37 dB at X-band frequency region.

    17. Biomimetic composite coating on rapid prototyped scaffolds for bone tissue engineering.

      Science.gov (United States)

      Arafat, M Tarik; Lam, Christopher X F; Ekaputra, Andrew K; Wong, Siew Yee; Li, Xu; Gibson, Ian

      2011-02-01

      The objective of this present study was to improve the functional performance of rapid prototyped scaffolds for bone tissue engineering through biomimetic composite coating. Rapid prototyped poly(ε-caprolactone)/tri-calcium phosphate (PCL/TCP) scaffolds were fabricated using the screw extrusion system (SES). The fabricated PCL/TCP scaffolds were coated with a carbonated hydroxyapatite (CHA)-gelatin composite via biomimetic co-precipitation. The structure of the prepared CHA-gelatin composite coating was studied by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy and Fourier transform infrared spectroscopy. Compressive mechanical testing revealed that the coating process did not have any detrimental effect on the mechanical properties of the scaffolds. The cell-scaffold interaction was studied by culturing porcine bone marrow stromal cells (BMSCs) on the scaffolds and assessing the proliferation and bone-related gene and protein expression capabilities of the cells. Confocal laser microscopy and SEM images of the cell-scaffold constructs showed a uniformly distributed cell sheet and accumulation of extracellular matrix in the interior of CHA-gelatin composite-coated PCL/TCP scaffolds. The proliferation rate of BMSCs on CHA-gelatin composite-coated PCL/TCP scaffolds was about 2.3 and 1.7 times higher than that on PCL/TCP scaffolds and CHA-coated PCL/TCP scaffolds, respectively, by day 10. Furthermore, reverse transcription polymerase chain reaction and Western blot analysis revealed that CHA-gelatin composite-coated PCL/TCP scaffolds stimulate osteogenic differentiation of BMSCs the most, compared with PCL/TCP scaffolds and CHA-coated PCL/TCP scaffolds. These results demonstrate that CHA-gelatin composite-coated rapid prototyped PCL/TCP scaffolds are promising for bone tissue engineering. Copyright © 2010 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

    18. Electrolytic Synthesis of Ni-W-MWCNT Composite Coating for Alkaline Hydrogen Evolution Reaction

      Science.gov (United States)

      Elias, Liju; Hegde, A. Chitharanjan

      2018-03-01

      Nickel-tungsten multi-walled carbon nanotube (Ni-W-MWCNT) composite films were fabricated by an electrodeposition technique, and their electrocatalytic activity toward hydrogen evolution reaction (HER) was studied. Ni-W-MWCNT composite films with a homogeneous dispersion of MWCNTs were deposited from an optimal Ni-W plating bath containing functionalized MWCNTs, under galvanostatic condition. The presence of functionalized MWCNT was found to enhance the induced codeposition of the reluctant metal W and resulted in a W-rich composite coating with improved properties. The electrocatalytic behaviors of Ni-W-MWCNT composite coating toward HER were studied by cyclic voltammetry (CV) and chronopotentiometry techniques in 1.0 M KOH medium. Further, Tafel polarization and electrochemical impedance spectroscopy (EIS) studies were carried out to establish the kinetics of HER on the alloy and composite electrodes. The experimental results revealed that the addition of MWCNTs (having a diameter of around 10-15 nm) into the alloy plating bath has a significant effect on the electrocatalytic behavior of Ni-W alloy deposit. The Ni-W-MWCNT composite coating was found to show better HER activity than the conventional Ni-W alloy coating. The enhanced electrocatalytic activity of Ni-W-MWCNT composite coating is attributed to the MWCNT intersticed in the deposit matrix, evidenced by surface morphology, composition and phase structure of the coating through SEM, EDS and XRD analyses, respectively.

    19. Carbon foam/hydroxyapatite coating for carbon/carbon composites: Microstructure and biocompatibility

      Energy Technology Data Exchange (ETDEWEB)

      Zhang, Leilei, E-mail: zhangleilei1121@aliyun.com; Li, Hejun; Li, Kezhi; Zhang, Shouyang; Lu, Jinhua; Li, Wei; Cao, Sheng; Wang, Bin

      2013-12-01

      To improve the surface biocompatibility of carbon/carbon composites, a carbon foam/hydroxyapatite coating was applied using a combination method of slurry procedure and ultrasound-assisted electrochemical deposition procedure. The morphology, microstructure and chemical composition of the coating were investigated by scanning electron microscopy, energy dispersive X-ray spectroscopy, Fourier transform infrared spectroscopy, Raman spectroscopy and X-ray diffraction. The biocompatibility of the carbon foam/hydroxyapatite coating was investigated by osteoblast-like MG63 cell culture tests. The results showed that the carbon foam could provide a large number of pores on the surface of carbon/carbon composites. The hydroxyapatite crystals could infiltrate into the pores and form the carbon foam/hydroxyapatite coating. The coating covered the carbon/carbon composites fully and uniformly with slice morphology. The cell response tests showed that the MG63 cells on carbon foam/hydroxyapatite coating had a better cell adhesion and cell proliferation than those on uncoated carbon/carbon composites. The carbon foam/hydroxyapatite coatings were cytocompatible and were beneficial to improve the biocompatibility. The approach presented here may be exploited for fabrication of carbon/carbon composite implant surfaces.

    20. Carbon foam/hydroxyapatite coating for carbon/carbon composites: Microstructure and biocompatibility

      International Nuclear Information System (INIS)

      Zhang, Leilei; Li, Hejun; Li, Kezhi; Zhang, Shouyang; Lu, Jinhua; Li, Wei; Cao, Sheng; Wang, Bin

      2013-01-01

      To improve the surface biocompatibility of carbon/carbon composites, a carbon foam/hydroxyapatite coating was applied using a combination method of slurry procedure and ultrasound-assisted electrochemical deposition procedure. The morphology, microstructure and chemical composition of the coating were investigated by scanning electron microscopy, energy dispersive X-ray spectroscopy, Fourier transform infrared spectroscopy, Raman spectroscopy and X-ray diffraction. The biocompatibility of the carbon foam/hydroxyapatite coating was investigated by osteoblast-like MG63 cell culture tests. The results showed that the carbon foam could provide a large number of pores on the surface of carbon/carbon composites. The hydroxyapatite crystals could infiltrate into the pores and form the carbon foam/hydroxyapatite coating. The coating covered the carbon/carbon composites fully and uniformly with slice morphology. The cell response tests showed that the MG63 cells on carbon foam/hydroxyapatite coating had a better cell adhesion and cell proliferation than those on uncoated carbon/carbon composites. The carbon foam/hydroxyapatite coatings were cytocompatible and were beneficial to improve the biocompatibility. The approach presented here may be exploited for fabrication of carbon/carbon composite implant surfaces.

    1. Composite Coatings with Ceramic Matrix Including Nanomaterials as Solid Lubricants for Oil-Less Automotive Applications

      Directory of Open Access Journals (Sweden)

      Posmyk A.

      2016-06-01

      Full Text Available The paper presents the theoretical basis of manufacturing and chosen applications of composite coatings with ceramic matrix containing nanomaterials as a solid lubricant (AHC+NL. From a theoretical point of view, in order to reduce the friction coefficient of sliding contacts, two materials are required, i.e. one with a high hardness and the other with low shear strength. In case of composite coatings AHC+NL the matrix is a very hard and wear resistant anodic oxide coating (AHC whereas the solid lubricant used is the nanomaterial (NL featuring a low shear strength such as glassy carbon nanotubes (GC. Friction coefficient of cast iron GJL-350 sliding against the coating itself is much higher (0.18-0.22 than when it slides against a composite coating (0.08-0.14. It is possible to reduce the friction due to the presence of carbon nanotubes, or metal nanowires.

    2. Formation of protective composite coatings with the use of solution of TFE telomers

      Science.gov (United States)

      Mashtalyar, D. V.; Gnedenkov, S. V.; Sinebryukhov, S. L.; Nadaraia, K. V.; Kiryukhin, D. P.; Kushch, P. P.; Kichigina, G. A.; Buznik, V. M.

      2017-09-01

      This paper presents the method of fabricate and the results of investigation of electrochemical properties and wettability of the composite coatings obtained on the magnesium alloy by plasma electrolytic oxidation (PEO) and the use of the solution of tetrafluoroethylene (TFE) telomers. The fluoropolymer-containing coatings decrease corrosion current density, increase contact angle in comparison with the base PEO-coating and the bare alloy.

    3. High-temperature protective coatings for C/SiC composites

      OpenAIRE

      Xiang Yang; Chen Zhao-hui; Cao Feng

      2014-01-01

      Carbon fiber-reinforced silicon carbide (C/SiC) composites were well-established light weight materials combining high specific strength and damage tolerance. For high-temperature applications, protective coatings had to provide oxidation and corrosion resistance. The literature data introduced various technologies and materials, which were suitable for the application of coatings. Coating procedures and conditions, materials design limitations related to the reactivity of the components of C...

    4. Chemical vapor deposited fiber coatings and chemical vapor infiltrated ceramic matrix composites

      Energy Technology Data Exchange (ETDEWEB)

      Kmetz, M.A.

      1992-01-01

      Conventional Chemical Vapor Deposition (CVD) and Organometallic Chemical Vapor Deposition (MOCVD) were employed to deposit a series of interfacial coatings on SiC and carbon yarn. Molybdenum, tungsten and chromium hexacarbonyls were utilized as precursors in a low temperature (350[degrees]C) MOCVD process to coat SiC yarn with Mo, W and Cr oxycarbides. Annealing studies performed on the MoOC and WOC coated SiC yarns in N[sub 2] to 1,000[degrees]C establish that further decomposition of the oxycarbides occurred, culminating in the formation of the metals. These metals were then found to react with Si to form Mo and W disilicide coatings. In the Cr system, heating in N[sub 2] above 800[degrees]C resulted in the formation of a mixture of carbides and oxides. Convention CVD was also employed to coat SiC and carbon yarn with C, Bn and a new interface designated BC (a carbon-boron alloy). The coated tows were then infiltrated with SiC, TiO[sub 2], SiO[sub 2] and B[sub 4]C by a chemical vapor infiltration process. The B-C coatings were found to provide advantageous interfacial properties over carbon and BN coatings in several different composite systems. The effectiveness of these different coatings to act as a chemically inert barrier layer and their relationship to the degree of interfacial debonding on the mechanical properties of the composites were examined. The effects of thermal stability and strength of the coated fibers and composites were also determined for several difference atmospheres. In addition, a new method for determining the tensile strength of the as-received and coated yarns was also developed. The coated fibers and composites were further characterized by AES, SEM, XPS, IR and X-ray diffraction analysis.

    5. Rhodium and Hafnium Influence on the Microstructure, Phase Composition, and Oxidation Resistance of Aluminide Coatings

      OpenAIRE

      Maryana Zagula-Yavorska; Małgorzata Wierzbińska; Jan Sieniawski

      2017-01-01

      A 0.5 μm thick layer of rhodium was deposited on the CMSX 4 superalloy by the electroplating method. The rhodium-coated superalloy was hafnized and aluminized or only aluminized using the Chemical vapour deposition method. A comparison was made of the microstructure, phase composition, and oxidation resistance of three aluminide coatings: nonmodified (a), rhodium-modified (b), and rhodium- and hafnium-modified (c). All three coatings consisted of two layers: the additive layer and the interdi...

    6. Development of a thin film vitreous bond based composite ceramic coating for corrosion and abrasion services

      International Nuclear Information System (INIS)

      Franke, B.

      2003-01-01

      IPC has been involved with the Alberta Research Council in developing a vitreous bond (VB) - based composite ceramic fluoropolymer coating technology. Compared to the present state of the art which is based on a hard discontinuous phase (ceramic particles) suspended in a soft continuous matrix (fluoropolymer mix) the novelty of our approach consists of designing a composite system in which both the ceramic and the fluoropolymer phases are continuous. The ceramic matrix will provide the strength and the erosion resistance for the fluoropolymer matrix even at high temperatures. The ceramic formulation employed is not affected by temperatures up to 500 o F while the fluoropolymer matrix provides a corrosion protection seal for the ceramic matrix. The inherent flexibility of the polymer matrix will protect against brittle fractures that may develop by handling or impact. Therefore the composite coating is able to withstand the deformation of the substrate without chipping or disbanding. The fluoropolymer matrix also provides dry lubrication properties further enhancing the erosion resistance of the ceramic phase. The thickness of the coating is very thin, in the 25 to 100 micron range. In summary, the coating technology is able to provide the following features: Corrosion protection levels similar to those of fluoropolymer coatings; Erosion resistance similar to that of ceramic coatings; Price comparable to that of polymer coatings; Exceptional wear resistance properties; and Capability for coating complicated shapes internally or externally or both. This paper will discuss the theory and development of this new technology and the resultant coating and potential properties. (author)

    7. Characterization of gas tunnel type plasma sprayed hydroxyapatite-nanostructure titania composite coatings

      Science.gov (United States)

      Yugeswaran, S.; Kobayashi, A.; Ucisik, A. Hikmet; Subramanian, B.

      2015-08-01

      Hydroxyapatite (HA) can be coated onto metal implants as a ceramic biocompatible coating to bridge the growth between implants and human tissue. Meanwhile many efforts have been made to improve the mechanical properties of the HA coatings without affecting its bioactivity. In the present study, nanostructure titania (TiO2) was mixed with HA powder and HA-nanostructure TiO2 composite coatings were produced by gas tunnel type plasma spraying torch under optimized spraying conditions. For this purpose, composition of 10 wt% TiO2 + 90 wt% HA, 20 wt% TiO2 + 80 wt% HA and 30 wt% TiO2 + 70 wt% HA were selected as the feedstock materials. The phase, microstructure and mechanical properties of the coatings were characterized. The obtained results validated that the increase in weight percentage of nanostructure TiO2 in HA coating significantly increased the microhardness, adhesive strength and wear resistance of the coatings. Analysis of the in vitro bioactivity and cytocompatibility of the coatings were done using conventional simulated body fluid (c-SBF) solution and cultured green fluorescent protein (GFP) labeled marrow stromal cells (MSCs) respectively. The bioactivity results revealed that the composite coating has bio-active surface with good cytocompatibility.

    8. Multiphase Nano-Composite Coatings for Achieving Energy Optimization

      Energy Technology Data Exchange (ETDEWEB)

      Nainaparampil, Jose

      2012-03-26

      UES Inc. and ANL teamed in this work to develop novel coating systems for the protection of surfaces from thermal degradation mainly in two applications; Machining and Die casting. These coatings were specifically designed for the purpose by incorporating required material phases and the overall architecture, which led to reduce the energy usage and increase efficiency of the operations. Following the UES/ANL's feasibility work, the coatings were developed utilizing High power impulse magnetron sputtering (HiPMS) and Large area filtered arc deposition (LAFAD) techniques. Toughness, hardness and oxidation resistance: contrasting qualities have been mixed in the right proportion to attain the suitable material characteristic for the cause. Hafnium diboride (HfB2) based materials provided such a system and its properties were tamed to attain the right combination of toughness and hardness by working on the microstructure and architecture of coatings. An effective interfacing material (graded concentrations of topcoat) was also achieved in this work to provide the required adhesion between the substrate and the coating. Combination of an appropriate bond coat and a functional top coat provided the present thermal degradation resistant coating for cutting tools and die-casting applications. Laboratory level performance tests and industrial level application tests by partner companies (Beta Site Testing) were used for the development of these coatings.

    9. Tribological properties of adaptive phosphate composite coatings with addition of silver and molybdenum disulfide

      Energy Technology Data Exchange (ETDEWEB)

      Liu, Cancan [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou (China); University of Chinese Academy of Sciences, Beijing (China); Chen, Lei, E-mail: chenlei@lzb.ac.cn [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou (China); Zhou, Jiansong, E-mail: jszhou@licp.cas.cn [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou (China); Zhou, Huidi; Chen, Jianmin [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou (China)

      2014-05-01

      Highlights: • A new kind of adaptive coatings was fabricated using relatively simple spraying techniques. • The tribological properties of Ag/MoS{sub 2} phosphate composite coatings were investigated at the temperature from 20 °C to 700 °C. • The composition and wear mechanisms of Ag/MoS{sub 2} phosphate composite coatings were also discussed. • The Ag/MoS{sub 2} phosphate composite coatings have self-repairing capability in the rubbing process at 700 °C. - Abstract: Adaptive phosphate composite coatings with addition of solid lubricants of molybdenum disulfide (MoS{sub 2}) and silver (Ag) using aluminum chromium phosphate as the binder were fabricated on high-temperature steel. The tribological properties of phosphate composite coatings were evaluated from room temperature (RT) to 700 °C. The phase composition and microstructure were investigated according to the characterization by power X-ray diffraction (XRD), Raman spectroscopy and scanning electron microscopy (SEM). The results show that the composite coating with the Ag/MoS{sub 2} mass ratio of 2:1 exhibits the stable and low friction coefficients from RT to 700 °C and relative low wear rates at all testing temperatures. The tribo-chemical reaction between Ag and MoS{sub 2} occurred in the rubbing process to form silver molybdates compounds lubricating film. The temperature-adaptive tribological properties were attributed to the formation of lubricating films composed of lubricants silver, MoS{sub 2} and silver molybdates phases on the worn surfaces of the composites coatings in a wide-temperature range.

    10. Microstructure and Mechanical Properties of Zn-Ni-Al2O3 Composite Coatings

      Directory of Open Access Journals (Sweden)

      Yang Bai

      2018-05-01

      Full Text Available Zn-Ni-Al2O3 composite coatings with different Ni contents were fabricated by low-pressure cold spray (LPCS technology. The effects of the Ni content on the microstructural and mechanical properties of the coatings were investigated. According to X-ray diffraction patterns, the composite coatings were primarily composed of metallic-phase Zn and Ni and ceramic-phase Al2O3. The energy-dispersive spectroscopy results show that the Al2O3 content of the composite coatings gradually decreased with increasing of Ni content. The cross-sectional morphology revealed thick, dense coatings with a wave-like stacking structure. The process of depositing Zn and Ni particles and Al2O3 particles by the LPCS method was examined, and the deposition mechanism was demonstrated to be mechanical interlocking. The bond strength, micro hardness and friction coefficient of the coatings did not obviously change when the Ni content varied. The presence of Al2O3 and Ni increased the wear resistance of the composite coatings, which was higher than that of pure Zn coatings, and the wear mechanism was abrasive and adhesive wear.

    11. Tribological Properties of Ti(Al,O)/Al2O3 Composite Coating by Thermal Spraying

      Science.gov (United States)

      Salman, Asma; Gabbitas, Brian; Cao, Peng; Zhang, Deliang

      The use of thermal spray coatings provides protection to the surfaces operating in severe environments. The main goal of the current work is to investigate the possibility of using a high velocity air fuel (HVAF) thermally sprayed wear resistant Ti(Al,O)/Al2O3 coating on tool steel (H13) which is used for making dies for aluminium high pressure die casting and dummy blocks aluminium extrusion. A feedstock of Ti(Al,O)/Al2O3 composite powder was produced from a mixture of Al and TiO2 powders by high energy mechanical milling, followed by a thermal reaction process. The feedstock was then thermally sprayed using a high velocity air-fuel (HVAF) technique onto H13 steel substrates to produce a composite coating. The present study describes and compares the tribological properties such as friction and sliding wear rate of the coating both at room and high temperature (700°C). The wear resistance of the coating was investigated by a tribometer using a spherical ended alumina pin as a counter body under dry and lubricating conditions. The results showed that composite coating has lower wear rate at high temperature than at room temperature without using lubricant. The composite coating was characterized using scanning electron microscopy (SEM), optical microscopy and X-ray diffractometry (XRD). This paper reports the experimental observations and discusses the wear resistance performance of the coatings at room and high temperatures.

    12. Characterization of nano-composite PVD coatings for wear-resistant applications

      NARCIS (Netherlands)

      Galvan, D.; Pei, Y.T.; de Hosson, J.T.M.; DeHosson, JTM; Brebbia, CA; Nishida, SI

      2005-01-01

      Various methodologies for the characterization of nano-composite coatings are discussed, which consist TiC nano-particles distributed in an amorphous hydrocarbon (a-C:H) matrix. Complications that arise from the influence of coating roughness and underlying substrate on the properties are evaluated

    13. Laser cladding of Al-Si/SiC composite coatings : Microstructure and abrasive wear behavior

      NARCIS (Netherlands)

      Anandkumar, R.; Almeida, A.; Vilar, R.; Ocelik, V.; De Hosson, J.Th.M.

      2007-01-01

      Surface coatings of an Al-Si-SiC composite were produced on UNS A03560 cast Al-alloy substrates by laser cladding using a mixture of powders of Al-12 wt.% Si alloy and SiC. The microstructure of the coatings depends considerably on the processing parameters. For a specific energy of 26 MJ/m2 the

    14. Functional regulation of Pb-Ti/MoS_2 composite coatings for environmentally adaptive solid lubrication

      International Nuclear Information System (INIS)

      Ren, Siming; Li, Hao; Cui, Mingjun; Wang, Liping; Pu, Jibin

      2017-01-01

      Highlights: • Co-doped Pb-Ti/MoS_2 composite coatings were successfully fabricated by unbalanced magnetron sputtering system. • Co-doped Pb-Ti/MoS_2 composite coatings showed lower friction coefficient and longer wear life in both humid and vacuum environments than that of single-doped ones. • The wear behaviours of Pb-Ti/MoS_2 composite coatings with the increase of Pb content is in accordance with the variation in H/E ratio that higher H/E is corresponding to the lower wear rate of coating. - Abstract: The lubrication of molybdenum disulfide coatings has commonly been limited by the application environments, for instance, the crystal MoS_2 are easily affected by water to form MoO_3 that causes a higher friction coefficient and short lifetime. Therefore, to improve the tribolgical performance of MoS_2 in high humidity condition, the co-doped Pb-Ti/MoS_2 composite coatings are deposited by unbalanced magnetron sputtering system. The design of the co-doping elements in MoS_2-based coatings can not only maintain the characteristic of low humidity-sensitivity as the Ti/MoS_2 coating but also improve the mechanical properties and tribological performance of coatings as a comparison with single-doped ones. Moreover, the ultra-low friction coefficient with a minimum value of 0.006 under the vacuum condition is achieved for Pb-Ti/MoS_2 composite coating containing about 4.6 at.% Pb, depending on the densification structure of coating. Intriguingly, the wear behaviours of Pb-Ti/MoS_2 composite coatings are in accordance with the variation in H/E (hardness to the elastic modulus) ratio that the coating with higher H/E exhibits lower wear rate. These results demonstrate that the lubricating properties of MoS_2 coatings in both humid environment and vacuum condition can be achieved through the Pb and Ti co-doped, which is of great significant for developing MoS_2 coatings as the environmentally adaptive lubricants.

    15. The Technology and Properties of Digital Double Pulse Electrodepositing Ni-HA Composite Coating of Bioceramics

      Institute of Scientific and Technical Information of China (English)

      DONG He-yan; WANG Zhou; SHI Gu-guizhi; FU Chuan-qi; CHEN Wei-rong; JIN Zhong-hong; LI Yan

      2004-01-01

      This article discusses and analyses the technology, the surface image, microstructure and ability of digital double pulse electrodepositing Ni-HA composite coatings of bioceramics made on 1Crl8Ni9Ti substrate by SEM ,XRD and so on. The results shows that ( 1 ) the HA particles exit in substrate uniformly; (2) XRD result shows that there are HA peaks at 78. 023 ° ,43. 246°and 73. 120°differently; (3) The microhardnees of the composite coatings is increased with the rise of content of HA particles, and on the same conditions the microhardnees value is greater than that of common non-pulse electrodepositing Ni-HA composite coatings of bioceramics. (4) The grain size of digital double pulse electrodepositing Ni-HA composite coatings of bioceramics is much thinner than that of common D. C.

    16. Electrophoretic deposition of PEEK-TiO 2 composite coatings on stainless steel

      KAUST Repository

      Seuß , Sigrid; Subhani, Tayyab; Yi Kang, Min; Okudaira, Kenji; Ventura, Isaac Aguilar; Boccaccini, Aldo R.

      2012-01-01

      Electrophoretic deposition (EPD) has been successfully used to deposit composite coatings composed of polyetheretherketone (PEEK) and titanium dioxide (TiO 2) nanoparticles on 316L stainless steel substrates. The suspensions of TiO2 nanoparticles

    17. 2-Mercaptobenzothiazole doped chitosan/11-alkanethiolate acid composite coating: Dual function for copper protection

      International Nuclear Information System (INIS)

      Bao Qi; Zhang Dun; Wan Yi

      2011-01-01

      Chitosan (CS) hydrogel loaded with the well-known corrosion inhibitor 2-mercaptobenzothiazole (MBT) has been introduced into a composite coating to improve copper protection. This composite coating, which has both anticorrosion and antibacterial properties, was fabricated onto the surface of copper by combining a simple self-assembled monolayer technique with a sol-gel method. The anti-corrosion ability of the coating in 3.5 wt.% NaCl solution was investigated by electrochemical methods including potentiodynamic polarization and electrochemical impedance spectroscopy. The protection efficiency of the coating is 97.70%, calculated on the basis of the corrosion current density. The stability and integrity of the composite coating were evaluated by field emission scanning electron microscopy (FESEM) and energy dispersive spectrometry (EDS). The FESEM and EDS results suggest that the composite coating endows the copper substrate with antibacterial properties, as untreated bare copper underwent microbiologically influenced corrosion in the presence of sulphate reducing bacteria (SRB). This antibacterial feature was further confirmed by the SRB culture method. In a 3.5% NaCl solution and highly corrosive SRB culture media, the as-prepared CS based composite coating gave corrosion protection by exhibiting better barrier effects against the attack of aggressive environments.

    18. Laser cladding of in situ TiB2/Fe composite coating on steel

      International Nuclear Information System (INIS)

      Du Baoshuai; Zou Zengda; Wang Xinhong; Qu Shiyao

      2008-01-01

      To enhance the wear resistance of mechanical components, laser cladding has been applied to deposit in situ TiB 2 /Fe composite coating on steel using ferrotitanium and ferroboron as the coating precursor. The phase constituents and microstructure of the composite coating were investigated using X-ray diffraction (XRD), scanning electron micrograph (SEM) and electron probe microanalysis (EPMA). Microhardness tester and block-on-ring wear tester were employed to measure the microhardness and dry-sliding wear resistance of the composite coating. Results show that defect-free composite coating with metallurgical joint to the steel substrate can be obtained. Phases presented in the coating consist of TiB 2 and α-Fe. TiB 2 particles which are formed in situ via nucleation-growth mechanism are distributed uniformly in the α-Fe matrix with blocky morphology. The microhardness and wear properties of the composite coating improved significantly in comparison to the as-received steel substrate due to the presence of the hard reinforcement TiB 2

    19. A novel combinatorial approach for the realization of advanced cBN composite coating

      International Nuclear Information System (INIS)

      Russell, W.C.; Yedave, S.N.; Sundaram, N.; Brown, W.D.; Malshe, A.P.

      2001-01-01

      The paper reports a novel coating process for the synthesis of hard material composite coatings. It consists of electrostatic spray coating (ESC) of powder particles (of micron-nanometer size) followed by chemical vapor infiltration (CVI) of a suitable binder phase. This novel approach enables fabrication of unique compositions such as cubic boron nitride (cBN) and titanium nitride (TiN) in a coating form. Recently, we have demonstrated the success of this technology by first coating a uniform over-layer (in excess of ∼ 10 μm) of cBN particles an carbide cutting tool inserts using ESC, followed by infiltration of particulate cBN matrix with TiN from its vapor phase using CVI to synthesize cBN-TiN a composite coating. The composite has shown excellent cBN-to-TiN and composite coating-to-carbide substrate adhesion. One of the main emphases of the paper is to discuss optimization and scale up of the ESC technology to achieve the desired microstructure and tailor the thickness across the cutting tool for better performance. Further, the cutting tools have been successfully tested for advanced machining applications. (author)

    20. Laser cladding of in situ TiB{sub 2}/Fe composite coating on steel

      Energy Technology Data Exchange (ETDEWEB)

      Du Baoshuai; Zou Zengda [School of Materials Science and Engineering, Shandong University, Jinan 250061 (China); Wang Xinhong [School of Materials Science and Engineering, Shandong University, Jinan 250061 (China)], E-mail: xinhongwang@sdu.edu.cn; Qu Shiyao [School of Materials Science and Engineering, Shandong University, Jinan 250061 (China)

      2008-08-15

      To enhance the wear resistance of mechanical components, laser cladding has been applied to deposit in situ TiB{sub 2}/Fe composite coating on steel using ferrotitanium and ferroboron as the coating precursor. The phase constituents and microstructure of the composite coating were investigated using X-ray diffraction (XRD), scanning electron micrograph (SEM) and electron probe microanalysis (EPMA). Microhardness tester and block-on-ring wear tester were employed to measure the microhardness and dry-sliding wear resistance of the composite coating. Results show that defect-free composite coating with metallurgical joint to the steel substrate can be obtained. Phases presented in the coating consist of TiB{sub 2} and {alpha}-Fe. TiB{sub 2} particles which are formed in situ via nucleation-growth mechanism are distributed uniformly in the {alpha}-Fe matrix with blocky morphology. The microhardness and wear properties of the composite coating improved significantly in comparison to the as-received steel substrate due to the presence of the hard reinforcement TiB{sub 2}.

    1. The characterization of an oxide interfacial coating for ceramic matrix composites

      Energy Technology Data Exchange (ETDEWEB)

      Coons, Timothy P., E-mail: tpcoons@gmail.com [Department of Chemistry, Unit 3060, University of Connecticut, 55 North Eagleville Road, Storrs, CT 06269-3060 (United States); Reutenauer, Justin W.; Mercado, Andrew [Department of Chemistry, Unit 3060, University of Connecticut, 55 North Eagleville Road, Storrs, CT 06269-3060 (United States); Kmetz, Michael A. [Pratt and Whitney, 400 Main Street M/S 114-43, East Hartford, CT 06108 (United States); Suib, Steven L. [Department of Chemistry, Unit 3060, University of Connecticut, 55 North Eagleville Road, Storrs, CT 06269-3060 (United States)

      2013-06-20

      This work focused on the use of metal organic chemical vapor deposition (MOCVD) to deposit a zinc oxide (ZnO) coating on ceramic fibers as an interfacial system for continuous fiber reinforced ceramic matrix composites (CFR-CMCs). ZnO coatings were deposited on ceramic grade (CG) Nicalon{sup ™}, Hi-Nicalon{sup ™}, and Hi-Nicalon{sup ™} Type S fabric by the thermal decomposition of zinc acetate dihydrate in a low pressure hot wall CVD reactor. A duplex SiO{sub 2} coating was also deposited in order to protect the ZnO layer from the reducing conditions during composite fabrication. Tow testing was used to evaluate the effect of the ZnO coating on the strength retention of the ceramic fabrics. Single strand unidirectional mini composites were fabricated by infiltrating SiC into the ZnO/SiO{sub 2} duplex coated tows in order to understand the interfacial properties of the ZnO coating. The mini composite utilizing Hi-Nicalon{sup ™} Type S produced the highest ultimate tensile strength (UTS) of 330 MPa. The coated fabrics and the mini composites were characterized using field emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD) and scanning Auger microscopy (SAM)

    2. The characterization of an oxide interfacial coating for ceramic matrix composites

      International Nuclear Information System (INIS)

      Coons, Timothy P.; Reutenauer, Justin W.; Mercado, Andrew; Kmetz, Michael A.; Suib, Steven L.

      2013-01-01

      This work focused on the use of metal organic chemical vapor deposition (MOCVD) to deposit a zinc oxide (ZnO) coating on ceramic fibers as an interfacial system for continuous fiber reinforced ceramic matrix composites (CFR-CMCs). ZnO coatings were deposited on ceramic grade (CG) Nicalon ™ , Hi-Nicalon ™ , and Hi-Nicalon ™ Type S fabric by the thermal decomposition of zinc acetate dihydrate in a low pressure hot wall CVD reactor. A duplex SiO 2 coating was also deposited in order to protect the ZnO layer from the reducing conditions during composite fabrication. Tow testing was used to evaluate the effect of the ZnO coating on the strength retention of the ceramic fabrics. Single strand unidirectional mini composites were fabricated by infiltrating SiC into the ZnO/SiO 2 duplex coated tows in order to understand the interfacial properties of the ZnO coating. The mini composite utilizing Hi-Nicalon ™ Type S produced the highest ultimate tensile strength (UTS) of 330 MPa. The coated fabrics and the mini composites were characterized using field emission scanning electron microscopy (FE-SEM), X-ray diffraction (XRD) and scanning Auger microscopy (SAM)

    3. Super-low friction behavior of nanostructured DLC composite coatings

      NARCIS (Netherlands)

      Pei, Y.T.; Galvan, D.; de Hosson, J.T.M.; DeHosson, JTM; Brebbia, CA; Nishida, SI

      2005-01-01

      Advanced TiC/a-C:H nanocomposite coatings have been produced via reactive deposition in a closed-field unbalanced magnetron sputtering system (Hauzer HTC-1000). This work concentrates on a detailed mechanical and tribological characterization of the TiC/a-C:H nanocomposite coatings, in particular

    4. Oxidation behaviour and electrical properties of cobalt/cerium oxide composite coatings for solid oxide fuel cell interconnects

      DEFF Research Database (Denmark)

      Harthøj, Anders; Holt, Tobias; Møller, Per

      2015-01-01

      This work evaluates the performance of cobalt/cerium oxide (Co/CeO2) composite coatings and pure Co coatings to be used for solid oxide fuel cell (SOFC) interconnects. The coatings are electroplated on the ferritic stainless steels Crofer 22 APU and Crofer 22H. Coated and uncoated samples...

    5. Comparison of lipid content and Fatty Acid composition in the edible meat of wild and cultured freshwater and marine fish and shrimps from china.

      Science.gov (United States)

      Li, Guipu; Sinclair, Andrew J; Li, Duo

      2011-03-09

      The lipid content and fatty acid composition in the edible meat of twenty-nine species of wild and cultured freshwater and marine fish and shrimps were investigated. Both the lipid content and fatty acid composition of the species were specified due to their unique food habits and trophic levels. Most of the marine fish demonstrated higher lipid content than the freshwater fish, whereas shrimps had the lowest lipid content. All the marine fish and shrimps had much higher total n-3 PUFA than n-6 PUFA, while most of the freshwater fish and shrimps demonstrated much lower total n-3 PUFA than n-6 PUFA. This may be the biggest difference in fatty acid composition between marine and freshwater species. The cultured freshwater fish demonstrated higher percentages of total PUFA, total n-3 PUFA, and EPA + DHA than the wild freshwater fish. Two freshwater fish, including bighead carp and silver carp, are comparable to the marine fish as sources of n-3 PUFA.

    6. Microstructural characterisation of electrodeposited coatings of metal matrix composite with alumina nanoparticles

      International Nuclear Information System (INIS)

      Indyka, P; Beltowska-Lehman, E; Bigos, A

      2012-01-01

      In the present work a nanocrystalline Ni-W metallic matrix was used to fabricate Ni-W/Al 2 O 3 composite coatings. The MMC (metal matrix composite) coatings with inert α-Al 2 O 3 particles (30 - 90 nm) were electrodeposited from aqueous electrolytes under direct current (DC) and controlled hydrodynamic conditions in a system with a rotating disk electrode (RDE). The chemical composition and microstructure of electrodeposited composites mainly control their functional properties; however, the particles must be uniformly dispersed to exhibit the dispersion-hardening effect. In order to increase the alumina particles incorporation as well as to promote the uniform distribution of the ceramic phase in a matrix, outer ultrasonic field was applied during electrodeposition. The influence of embedded alumina nanoparticles on structural characteristics (morphology, phase composition, residual stresses) of the resulting Ni-W/Al 2 O 3 coatings was investigated in order to obtain a nanocomposite with high hardness and relatively low residual stresses. Surface and cross-section morphology and the chemical composition of deposits was examined in the scanning electron microscope, the EDS technique was used. Microstructure and phase composition were determined by transmission electron microscopy and X-ray diffraction. Based on microstructural and micromechanical properties of the coatings, the optimum conditions for obtaining crack-free homogeneous Ni-W/Al 2 O 3 composite coatings have been determined.

    7. Biocompatibility of sol-gel hydroxyapatite-titania composite and bilayer coatings

      International Nuclear Information System (INIS)

      Sidane, D.; Rammal, H.; Beljebbar, A.; Gangloff, S.C.; Chicot, D.; Velard, F.; Khireddine, H.

      2017-01-01

      Titania-Hydroxyapatite (TiO 2 /HAP) reinforced coatings are proposed to enhance the bioactivity and corrosion resistance of 316L stainless steel (316L SS). Herein, spin- and dip-coating sol-gel processes were investigated to construct two kinds of coatings: TiO 2 /HAP composite and TiO 2 /HAP bilayer. Physicochemical characterization highlighted the bioactivity response of the TiO 2 /HAP composite once incubated in physiological conditions for 7 days whereas the TiO 2 /HAP bilayer showed instability and dissolution. Biological analysis revealed a failure in human stem cells adhesion on TiO 2 /HAP bilayer whereas on TiO 2 /HAP composite the presence of polygonal shaped cells, possessing good behaviour attested a good biocompatibility of the composite coating. Finally, TiO 2 /HAP composite with hardness up to 0.6 GPa and elastic modulus up to 18 GPa, showed an increased corrosion resistance of 316L SS. In conclusion, the user-friendly sol-gel processes led to bioactive TiO 2 /HAP composite buildup suitable for biomedical applications. - Highlights: • 316L SS implant TiO 2 reinforced HAP coatings were investigated and compared. • TiO 2 /HAP composite had better structural features and biocompatible properties. • Improvement of 316L SS implants corrosion resistance. • TiO 2 /HAP composite mechanical properties close to bone tissue • Low cost and desired material for hard tissue applications

    8. Self-sealing multilayer coating for SiC/SiC composites

      International Nuclear Information System (INIS)

      Ferraris, M.; Appendino Montorsi, M.; Salvo, M.; Isola, C.; Kohyama, A.

      1997-01-01

      A double layer coating for SiC/SiC for fusion applications is proposed: the first layer consists in a homogeneous, crack free, glass-ceramic with high characteristic temperatures and thermal expansion coefficient compatible to the composite one; the second layer is amorphous and shows self-sealing properties above 700degC. The glass and the glass-ceramic materials used for this double layer coating do not contain lithium and boron oxide, making them particularly interesting for thermonuclear fusion applications. The self-sealing property of the double layer coating was valued by inducing cracks on the coatings and observing their reparation after heating. (author)

    9. Study of Thermal Fatigue Resistance of a Composite Coating Made by a Vacuum Fusion Sintering Method

      Institute of Scientific and Technical Information of China (English)

      2003-01-01

      Thermal fatigue behavior of a Ni-base alloy chromium carbide composite coating made by a vacuum fusion sintering method are discussed. Results show that thermal fatigue behavior is associated with cyclic upper temperature and coating thickness. As the thickness of the coating decreases, the thermal fatigue resistance increases. The thermal fatigue resistance cuts down with the thermal cyclic upper temperature rising. The crack growth rate decreases with the increase in cyclic number until crack arrests. Thermal fatigue failure was not found along the interface of the coating/matrix. The tract of thermal fatigue crack cracks along the interfaces of phases.

    10. Structure and properties of composite iron-based coatings obtained by the electromechanical technique

      Science.gov (United States)

      Dubinskii, N. A.

      2007-09-01

      The influence of the electrolyte temperature and current density on the content of inclusions of powder particles in composite coatings obtained by the electrochemical technique has been investigated. It has been found that the wear resistance of iron coatings with inclusions of powder particles of aluminum, kaolin, and calcium silicate increases from 5 to 10 times compared to coating without inclusions of disperse particles, and the friction coefficient therewith decreases from 0.097 to 0.026. It has been shown that the mechanical properties of iron obtained by the method of electrochemical deposition depend on their fine structure. The regimes of deposition of iron-based coatings have been optimized.

    11. Development of Ferrite-Coated Soft Magnetic Composites: Correlation of Microstructure to Magnetic Properties

      Science.gov (United States)

      Sunday, Katie Jo

      Soft magnetic composites (SMCs) comprised of ferrite-coated ferrous powder permit isotropic magnetic flux capabilities, lower core losses, and complex designs through the use of traditional powder metallurgy techniques. Current coating materials and methods are vastly limited by the nonmagnetic properties of organic and some inorganic coatings and their inability to withstand high heat treatments for proper stress relief of core powder after compaction. Ferrite-based coatings are ferrimagnetic, highly resistive, and boast high melting temperatures, thus providing adequate electrical barriers between metallic particles. These insulating layers are necessary for reducing eddy current losses by increasing resistivity in order to improve the overall magnetic efficiency and subsequent frequency range. The goals of this work are to correlate ferrite-coated Fe powder composites microstructure for the coating and core powder to magnetic properties such as permeability, coercivity, and core loss. We first explore the relevant concepts of SMC materials from their composition to processing steps to pertinent properties. This thesis employs a suite of characterization techniques for powder and composite properties. We use X-ray diffraction, scanning electron microscopy, and transmission electron microscopy to provide a complete understanding of the effect of processing conditions on ferrite-coated Fe-based SMCs. Magnetic, mechanical, and electrical properties are then analyzed to correlate microstructural features and determine their effect on such properties. In the second part of this thesis, we present a proof of concept study on Al2O3- and Al2O3- Fe3O4-coated Fe powder composites, illustrating magnetization is highly dependent on ferromagnetic volume. We then expand on previous work to compare an ideal, crystalline state using Fe3O 4-Fe thin film heterostructures to a highly strained state using bulk powder studies. Fe3O4-coated Fe composites are produced via mechanical

    12. Influence of current density on microstructure and properties of electrodeposited nickel-alumina composite coatings

      International Nuclear Information System (INIS)

      Góral, Anna; Nowak, Marek; Berent, Katarzyna; Kania, Bogusz

      2014-01-01

      Highlights: • Current density of the electrodeposition affects the incorporation of Al 2 O 3 in Ni matrix. • Ni/Al 2 O 3 composite coatings exhibit changes in crystallographic texture. • The pitting corrosion effects were observed in Ni/Al 2 O 3 coatings. • Residual stresses were decreased with increasing current density and coating thickness. - Abstract: Electrodeposition process is a very promising method for producing metal matrix composites reinforced with ceramic particles. In this method insoluble particles suspended in an electrolytic bath are embedded in a growing metal layer. This paper is focused on the investigations of the nickel matrix nanocomposite coatings with hard α-Al 2 O 3 nano-particles, electrochemically deposited from modified Watts-type baths on steel substrates. The influence of various current densities on the microstructure, residual stresses, texture, hardness and corrosion resistance of the deposited nickel/alumina coatings was investigated. The surface morphology, cross sections of the coatings and distribution of the ceramic particles in the metal matrix were examined by scanning electron microscopy. The phase composition, residual stresses and preferred grain orientation of the coatings were characterized using X-ray diffraction techniques. The coating morphology revealed that α-Al 2 O 3 particles show a distinct tendency to form agglomerates, approximately uniformly distributed into the nickel matrix

    13. A STUDY ON MICROSTRUCTURE CHARACTERISTICS OF IN SITU FORMED TiC REINFORCED COMPOSITE COATINGS

      OpenAIRE

      PENG LIU; WEI GUO; HUI LUO

      2012-01-01

      In situ synthesized TiC reinforced composite coating was fabricated by laser cladding of Al-Ni-Cr-C powders on titanium alloys, which can greatly improve the surface performance of the substrate. In this study, the Al-Ni-Cr-C laser-cladded composite coatings have been researched by means of X-ray diffraction, scanning electron microscope (SEM) and electron probe micro-analyzer (EPMA). There was a metallurgical combination between the Al-Ni-Cr-C laser-cladded coating and the Ti-6Al-4V substrat...

    14. Effect of chemical composition of steel on the structure of hot – dip galvanized coating

      Directory of Open Access Journals (Sweden)

      P. Pokorny

      2016-01-01

      Full Text Available This article describes the effect of the content of conventional steel impurity elements on the thickness and composition of the zinc layer. This article is focused primarily on low-temperature, batch hot-dip galvanizing; however, the continuous coating process is also mentioned. The main discussion covers galvanizing from pure zinc melt, and only touches on galvanizing from melts with the usual amounts of aluminium (0,2 wt. %. Silicon, phosphorus, aluminium and sulfur may have an especially negative effect on the mechanical properties of the coating and its final appearance. The content of ballast carbon and manganese has a rather limited effect on composition and coating thickness.

    15. EB-curing of coatings on wood composite boards

      International Nuclear Information System (INIS)

      Czvikovszky, T.; Czajlic, I.; Takacs, E.; Ille, A.; Salleh, N.G.; Alpar, T.

      1988-01-01

      The industrial radiation processing using low energy electron beam (EB) accelerators lower than 300 keV offers high speed, safe technologies for the chemical conversion of thin layer coatings. Because of the nonselective mode of initiating chain reaction polymerization involving free radicals in synthetic coating layers and suitable substrates, the EB curing of the coatings on woods and papers has particular advantage. Hungary decided to start an up-to-date EB line to process cement-bound (CB) wood chipboards with pigmented acrylic coatings. The CB wood chipboards contain more than 60 % of portland cement and up to 40 % of wood particles. They are produced as large boads of 6 - 16 mm thickness. In their fireproof character and other aspects, they are similar to asbestos-cement boards without containing carcinagenic asbestos, and are stable against moisture and atmospheric influences. EB-cured acrylate coating improved further those properties, and makes them valuable structural material. Oligomers and monomers as the main components of EB curable coatings, the irradiation with a Van de Graaff type electron accelerator of 2 MeV and the results are reported. The oligomers play the most important role in the formation of radiation curable coatings. (K.I.)

    16. On the interfacial degradation mechanisms of thermal barrier coating systems: Effects of bond coat composition

      Energy Technology Data Exchange (ETDEWEB)

      Wu, R.T., E-mail: WU.Rudder@nims.go.jp [International Center for Young Scientists, National Institute for Materials Science, 1-2-1 Sengen, Tsukuba City, Ibaraki (Japan); Wang, X.; Atkinson, A. [Department of Materials, Imperial College London, Prince Consort Road, London SW7 2BP (United Kingdom)

      2010-10-15

      Thermal barrier coating (TBC) systems based on an electron beam physical vapour deposited, yttria-stabilized zirconia (YSZ) top coat and a substrate material of CMSX-4 superalloy were identically prepared to systematically study the behaviour of different bond coats. The three bond coat systems investigated included two {beta}-structured Pt-Al types and a {gamma}-{gamma}' type produced by Pt diffusion without aluminizing. Progressive evolution of stress in the thermally grown aluminium oxide (TGO) upon thermal cycling, and its relief by plastic deformation and fracture, were studied using luminescence spectroscopy. The TBCs with the LT Pt-Al bond coat failed by a rumpling mechanism that generated isolated cracks at the interface between the TGO and the YSZ. This reduced adhesion at this interface and the TBC delaminated when it could no longer resist the release of the stored elastic energy of the YSZ, which stiffened with time due to sintering. In contrast, the TBCs with Pt diffusion bond coats did not rumple, and the adhesion of interfaces in the coating did not obviously degrade. It is shown that the different failure mechanisms are strongly associated with differences in the high-temperature mechanical properties of the bond coats.

    17. Structure and phase composition of titanium nitride coating on austenitic steel

      International Nuclear Information System (INIS)

      Dubovitskaya, N.V.; Kolenchenko, L.D.; Larikov, L.N.

      1989-01-01

      Structure and phase composition of titanium nitride coating deposited on 08Kh18N10T steel substrate using ''Bulat'' device are studied. Use of complex investigation methods permitted despite small coating thickness (1μm) to aquire information on hardness, porosity, to study phase composition in all coating thickness. The surface layer (∼0.1 μm) consists of ε-Ti 2 N, TiN 0.6 , TiC 0.35 , that is formed with carbon participation from oil vacuum. In more deeper layers beside ε-Ti 2 N TiC 0.14 N 0.77 is present. Effect of carbon diffusion from substrate to forming coating is stated. Gradient of element concentrations in the substrate-coating interface causes recrystallization of austenite

    18. Fretting and wear behaviors of Ni/nano-WC composite coatings in dry and wet conditions

      International Nuclear Information System (INIS)

      Benea, Lidia; Başa, Sorin-Bogdan; Dănăilă, Eliza; Caron, Nadège; Raquet, Olivier; Ponthiaux, Pierre; Celis, Jean-Pierre

      2015-01-01

      Highlights: • The friction and wear properties of Ni/nano-WC composite were studied. • Nano-WC reinforcement decreased friction coefficient in dry and wet conditions. • Nano-WC reinforcement fraction was seen to be 12 wt.%. • Nanohardness increased by 27% compared to nickel without WC reinforcements. • Ennoblement of OCP corresponding to the Ni/nano-WC composite coating. - Abstract: The fretting and wear behaviors of Ni/nano-WC composite coatings were studied by considering the effect of fretting frequency of 1 Hz during 10,000 cycles, at different applied loads in dry or wet conditions. The studies were performed on a ball-on-disk tribometer and the results were compared with pure Ni coating. The nanohardness of pure Ni and Ni/nano-WC composite coatings was tested by nanoindentation technique. To evaluate the wet wear (tribocorrosion) behavior the open circuit potential (OCP) was measured before, during and after the fretting tests at room temperature in the solution that simulates the primary water circuit of Pressurized Water Reactors (PWRs). The results show that Ni/nano-WC composite coatings exhibited a low friction coefficient, high nanohardness and wear resistance compared with pure Ni coatings under similar experimental conditions. Ni/nano-WC composite coatings were obtained on stainless steel support by electrochemical codeposition of nano-sized WC particles (diameter size of ∼60 nm) with nickel, from a standard nickel Watts plating bath. The surface morphology and the composition of the coatings were characterized by scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDX) respectively

    19. Progress in Tribological Properties of Nano-Composite Hard Coatings under Water Lubrication

      Directory of Open Access Journals (Sweden)

      Qianzhi Wang

      2017-02-01

      Full Text Available The tribological properties, under water-lubricated conditions, of three major nano-composite coatings, i.e., diamond-like carbon (DLC or a-C, amorphous carbon nitride (a-CNx and transition metallic nitride-based (TiN-based, CrN-based, coatings are reviewed. The influences of microstructure (composition and architecture and test conditions (counterparts and friction parameters on their friction and wear behavior under water lubrication are systematically elucidated. In general, DLC and a-CNx coatings exhibit superior tribological performance under water lubrication due to the formation of the hydrophilic group and the lubricating layer with low shear strength, respectively. In contrast, TiN-based and CrN-based coatings present relatively poor tribological performance in pure water, but are expected to present promising applications in sea water because of their good corrosion resistance. No matter what kind of coatings, an appropriate selection of counterpart materials would make their water-lubricated tribological properties more prominent. Currently, Si-based materials are deemed as beneficial counterparts under water lubrication due to the formation of silica gel originating from the hydration of Si. In the meantime, the tribological properties of nano-composite coatings in water could be enhanced at appropriate normal load and sliding velocity due to mixed or hydrodynamic lubrication. At the end of this article, the main research that is now being developed concerning the development of nano-composite coatings under water lubrication is described synthetically.

    20. Fabrication and electromagnetic interference shielding effectiveness of polymeric composites filled with silver-coated microorganism cells

      Energy Technology Data Exchange (ETDEWEB)

      Lan, Mingming, E-mail: lan_mingming@163.com [College of Mechanical and Electrical Engineering, Henan Agricultural University, Zhengzhou 450002 (China); Zhang, Deyuan; Cai, Jun; Hu, Yanyan; Yuan, Liming [Bionic and Micro/Nano/Bio Manufacturing Technology Research Center, School of Mechanical Engineering and Automation, Beihang University, Beijing 100191 (China)

      2014-07-01

      In this paper, helical silver-coated Spirulina cells were used as conductive fillers for the fabrication of polymeric composites. The morphology and composition of the coated Spirulina cells were analyzed with scanning electron microscope and energy dispersive X-ray spectrometer. The densities of silver-coated Spirulina cells were measured using the standard Archimedes method with distilled water. The electrical resistivity was measured by four-probe technique using ammeter and voltmeter whereas electromagnetic interference shielding effectiveness was measured by four-port method using vector network analyzer and coaxial-airline sample holder. The results showed that the silver-coated Spirulina cells with different coating thickness were lightweight fillers compared to the other typical conductive particles. The polymeric composites could achieve good conductivity at the lower content of silver-coated Spirulina cells owing to their helical shape. The shielding effectiveness of polymeric composites had a strong dependence on their conductivity. At the coating thickness of 0.96 μm and the content of 40 vol%, the shielding effectiveness could reach above 74.3 dB in entire test wave band.

    1. Development of high performance electroless Ni-P-HNT composite coatings

      Science.gov (United States)

      Ranganatha, S.; Venkatesha, T. V.; Vathsala, K.

      2012-12-01

      Halloysite nanotubes (HNTs) of the dimension 50 nm × 1-3 μm (diameter × length) are utililized to fabricate the alloy composite by employing electroless/autocatalytic deposition technique. Electroless Ni-P-HNT binary alloy composite coatings are prepared successfully on low carbon steel. These nanotubes were made to get inserted/incorporated into nickel matrix and corresponding composites are examined for their electrochemical, mechanical and tribological performances and compared with that of plain Ni-P. The coatings were characterized using scanning electron microscopy (SEM) and Energy dispersive X-ray analysis (EDX) techniques to analyze surface nature and composition correspondingly. Small amount of incorporated HNTs made Ni-P deposits appreciable enhancement and betterment in corrosion resistance, hardness and friction resistance. This drastic improvement in the properties reflects the effect of addition of HNTs into Ni-P matrix leading to the development of high performance Ni-P-HNT composite coatings.

    2. Mechanical properties of nanodiamond-reinforced hydroxyapatite composite coatings deposited by suspension plasma spraying

      Science.gov (United States)

      Chen, Xiuyong; Zhang, Botao; Gong, Yongfeng; Zhou, Ping; Li, Hua

      2018-05-01

      Hydroxyapatite (HA) coatings suffer from poor mechanical properties, which can be enhanced via incorporation of secondary bioinert reinforcement material. Nanodiamond (ND) possesses excellent mechanical properties to play the role as reinforcement for improving the mechanical properties of brittle HA bioceramic coatings. The major persistent challenge yet is the development of proper deposition techniques for fabricating the ND reinforced HA coatings. In this study, we present a novel deposition approach by plasma spraying the mixtures of ND suspension and micron-sized HA powder feedstock. The effect of ND reinforcement on the microstructure and the mechanical properties of the coatings such as hardness, adhesive strength and friction coefficient were examined. The results showed that the ND-reinforced HA coatings display lower porosity, fewer unmelted particles and uniform microstructure, in turn leading to significantly enhanced mechanical properties. The study presented a promising approach to fabricate ND-reinforced HA composite coatings on metal-based medical implants for potential clinical application.

    3. Formation mechanism of a silicon carbide coating for a reinforced carbon-carbon composite

      Science.gov (United States)

      Rogers, D. C.; Shuford, D. M.; Mueller, J. I.

      1975-01-01

      Results are presented for a study to determine the mechanisms involved in a high-temperature pack cementation process which provides a silicon carbide coating on a carbon-carbon composite. The process and materials used are physically and chemically analyzed. Possible reactions are evaluated using the results of these analytical data. The coating is believed to develop in two stages. The first is a liquid controlled phase process in which silicon carbide is formed due to reactions between molten silicon metal and the carbon. The second stage is a vapor transport controlled reaction in which silicon vapors react with the carbon. There is very little volume change associated with the coating process. The original thickness changes by less than 0.7%. This indicates that the coating process is one of reactive penetration. The coating thickness can be increased or decreased by varying the furnace cycle process time and/or temperature to provide a wide range of coating thicknesses.

    4. Microstructures and tribological properties of laser cladded Ti-based metallic glass composite coatings

      Energy Technology Data Exchange (ETDEWEB)

      Lan, Xiaodong; Wu, Hong, E-mail: wuhong927@126.com; Liu, Yong, E-mail: yonliu@csu.edu.cn; Zhang, Weidong; Li, Ruidi; Chen, Shiqi; Zai, Xiongfei; Hu, Te

      2016-10-15

      Metallic glass composite coatings Ti{sub 45}Cu{sub 41}Ni{sub 9}Zr{sub 5} and Ti{sub 45}Cu{sub 41}Ni{sub 6}Zr{sub 5}Sn{sub 3} (at.%) on a Ti-30Nb-5Ta-7Zr (wt.%) (TNTZ) alloy were prepared by laser cladding. The microstructures of the coatings were characterized by means of X-ray diffractometry (XRD), scanning electron microscopy (SEM) equipped with energy dispersive X-ray analyzer (EDXA), and transmission electron microscopy (TEM). Results indicated that the coatings have an amorphous structure embedded with a few nanocrystalline phases and dendrites. A partial substitution of Ni by Sn can improve the glass forming ability of Ti-base metallic glass system, and induce the formation of nano-sized Ni{sub 2}SnTi phase during the cyclic laser heating. The tribological behavior of both the substrate and the coatings was investigated in detail. A significant improvement in both the hardness and the wear resistance of the coatings was achieved with the addition of Sn. The relationship between the wear resistance and the microstructures of the coatings was discussed. - Highlights: •Ti-based metallic glass composite coatings were prepared by laser cladding. •The wear resistance is greatly improved by laser cladding of composite coatings. •Substitution of Ni by Sn increases GFA and wear resistance of the coatings. •A good balance of crystalline/amorphous phases improves the wear resistance. •Adhesive wear serves as the dominant wear mechanism of the composite coatings.

    5. Designing, preparing and evaluation of novel HA/Ti composite coating for endodontic dental implant

      Directory of Open Access Journals (Sweden)

      Fathi MH.

      2002-08-01

      Full Text Available Nowadays, application of implants as a new method for replacing extracted teeth have been improved. So, many researches have been performed for improving the characteristics of implants. The aim of this study was to design and produce a desired coating in order to obtaining two goals including; improvement of the corrosion behavior of metallic endodontic implant and the bone osseointegration simultaneously. Stainless steel 316L (SS, cobalt-chromium alloy (Vit and commercial pure titanium (cpTi were chosen as metallic substrates and hydroxyapatite coating (HAC were performed by plasma-spraying (PS process on three different substrates. A novel double layer Hydroxyapatite/Titanium (HA/Ti composite coating composed of a HA top layer and a Ti under layer was prepared using PS and physical vapor deposition (PVD process respectively on SS. Structural characterization techniques including XRD, SEM and EDX were utilized to investigate the microstructure, morpholgy and crystallinity of the coatings. Electrochemical potentiodynamic tests were performed in physiological solutions in order to determine and compare the corrosion behavior of the coated and uncoated specimens behavior as an indication of biocmpatibility. Results indicated that the cpTi possesses the highest and SS the lowest corrosion resistance (highest corrosion current density between uncoated substrates. This trend was independent to the type of physiological environment. The HA coating decreased the corrosion current density of HA coated metallic implants but did not change that trend. HAC acted as a mechanical barrier on the metallic substrate but could not prevent the interaction between metallic substrate and environment completely. The HA/Ti composite coating improved the corrosion behavior of SS. The corrosion current density of HA/Ti coated SS decreased and was exactly similar to single HA coated cpTi in physiological solutions. The results indicated that HA/Ti composite coated SS

    6. Tribological properties of thermally sprayed TiAl-Al2O3 composite coating

      Science.gov (United States)

      Salman, A.; Gabbitas, B.; Li, J.; Zhang, D.

      2009-08-01

      The use of thermal spray coatings provides protection to the surfaces operating in severe environments. The main goal of the current work is to investigate the possibility of using a high velocity oxy fuel (HVOF) thermally sprayed wear resistant TiAl/Al2O3 coating on tool steel (H13) which is used for making dies for aluminium high pressure die casting. A feedstock of TiAl/Al2O3 composite powder was produced from a mixture of Al and TiO2 powders by high energy mechanical milling, followed by a thermal reaction process. The feedstock was then thermally sprayed using a high velocity oxy-fuel (HVOF) technique onto H13 steel substrates to produce a composite coating. The present study describes and compares the tribological properties such as friction and sliding wear rate of the coating both at room and high temperature (700°C). The results showed that the composite coating has lower wear rate at high temperature (700°C) than the uncoated H13 sample. At Room temperature without using lubricant there is no much significant difference between the wear rate of the coated and uncoated samples. The experimental results showed that the composite coating has great potential for high temperature application due to its lower wear rate at high temperature in comparison with the uncoated sample at the same temperature. The composite coating was characterized using scanning electron microscopy (SEM), optical microscopy and X-ray diffractometry (XRD). This paper reports the experimental observations and discusses the wear resistance performance of the coatings at room and high temperatures.

    7. Tribological properties of thermally sprayed TiAl-Al2O3 composite coating

      International Nuclear Information System (INIS)

      Salman, A; Gabbitas, B; Zhang, D; Li, J

      2009-01-01

      The use of thermal spray coatings provides protection to the surfaces operating in severe environments. The main goal of the current work is to investigate the possibility of using a high velocity oxy fuel (HVOF) thermally sprayed wear resistant TiAl/Al 2 O 3 coating on tool steel (H13) which is used for making dies for aluminium high pressure die casting. A feedstock of TiAl/Al 2 O 3 composite powder was produced from a mixture of Al and TiO 2 powders by high energy mechanical milling, followed by a thermal reaction process. The feedstock was then thermally sprayed using a high velocity oxy-fuel (HVOF) technique onto H13 steel substrates to produce a composite coating. The present study describes and compares the tribological properties such as friction and sliding wear rate of the coating both at room and high temperature (700 deg. C). The results showed that the composite coating has lower wear rate at high temperature (700deg. C) than the uncoated H13 sample. At Room temperature without using lubricant there is no much significant difference between the wear rate of the coated and uncoated samples. The experimental results showed that the composite coating has great potential for high temperature application due to its lower wear rate at high temperature in comparison with the uncoated sample at the same temperature. The composite coating was characterized using scanning electron microscopy (SEM), optical microscopy and X-ray diffractometry (XRD). This paper reports the experimental observations and discusses the wear resistance performance of the coatings at room and high temperatures.

    8. Composite polymer-containing coatings on Mg alloys perspective for industry and implant surgery

      Science.gov (United States)

      Gnedenkov, S. V.; Sinebryukhov, S. L.; Mashtalyar, D. V.; Imshinetskiy, I. M.; Gnedenkov, A. S.; Minaev, A. N.

      2017-09-01

      In order to improve the corrosion resistance of magnesium alloys the ways of composite protective coating formation were developed by means of plasma electrolytic oxidation (PEO) as well as electrophoretic deposition methods. Electrochemical, corrosion, tribological, and morphological properties of the MAS magnesium alloy composite coatings were studied. The composite polymer-containing coating decrease the corrosion current density values by three orders of magnitude (Ic = 2.0 . 10-10 A/cm2), in comparison with the base PEO-layer. These polymer-containing layers enable one to expand the practical usage area of Mg alloys. The application of such coatings provides the increasing the bioactivity and regulate the corrosion rate of resorbable magnesium implants.

    9. Fabrication and evaluation of atmospheric plasma spraying WC-Co-Cu-MoS2 composite coatings

      International Nuclear Information System (INIS)

      Yuan Jianhui; Zhu Yingchun; Zheng Xuebing; Ji Heng; Yang Tao

      2011-01-01

      Research highlights: → Protective WC-Co-based coatings containing solid lubricant Cu and MoS 2 used in wear applications were investigated in this study. → It was found that the MoS 2 composition in the feed powder was kept in WC-Co-Cu-MoS 2 coatings, and the decomposition and decarburization of WC in APS process were improved. → Combining the wear resistance of WC with the lubricating properties of Cu and MoS 2 has an extremely beneficial effect on improving the tribological performance of the resulting coating. - Abstract: Protective WC-Co-based coatings containing solid lubricant Cu and MoS 2 used in wear applications were investigated in this study. These coatings were deposited on mild steel substrates by atmospheric plasma spraying (APS). The feedstock powders were prepared by mechanically mixing the solid lubricant powders and WC-Co powder, followed by sintering and crushing the mixtures to avoid different particle flighting trajectories at plasma. The tribological properties of the coatings against stainless steel balls were examined by ball-on-disk (BOD) tribometer under normal atmospheric condition. The microstructure of the coatings was studied by optical microscope, scanning electron microscope and X-ray diffraction. It was found that the MoS 2 composition in the feed powder was kept in WC-Co-Cu-MoS 2 coatings, and the decomposition and decarburization of WC in APS process were improved, which were attributed to the protection of Cu around them. The friction and wear behaviors of all the WC-Co-Cu-MoS 2 coatings were superior to that of WC-Co coating. Such behavior was associated to different wear mechanisms operating for WC-Co coating and the WC-Co-Cu-MoS 2 coatings.

    10. Polyester fabric coated with Ag/ZnO composite film by magnetron sputtering

      Energy Technology Data Exchange (ETDEWEB)

      Yuan, Xiaohong, E-mail: yxhong1981_2004@126.com [Key Laboratory of Eco-Textiles, Ministry of Education, Jiangnan University, Wuxi 214122, Jiangsu (China); Faculty of Clothing and Design, Minjiang University, Fuzhou 350121, Fujian (China); Xu, Wenzheng, E-mail: xwz8199@126.com [Key Laboratory of Eco-Textiles, Ministry of Education, Jiangnan University, Wuxi 214122, Jiangsu (China); Huang, Fenglin, E-mail: windhuang325@163.com [Key Laboratory of Eco-Textiles, Ministry of Education, Jiangnan University, Wuxi 214122, Jiangsu (China); Chen, Dongsheng, E-mail: mjuchen@126.com [Faculty of Clothing and Design, Minjiang University, Fuzhou 350121, Fujian (China); Wei, Qufu, E-mail: qfwei@jiangnan.edu.cn [Key Laboratory of Eco-Textiles, Ministry of Education, Jiangnan University, Wuxi 214122, Jiangsu (China)

      2016-12-30

      Highlights: • Ag/ZnO composite film was successfully deposited on polyester fabric by magnetron sputtering technique. • Ag film was easily oxidized into Ag{sub 2}O film in high vacuum oxygen environment. • The zinc film coated on the surface of Ag film before RF reactive sputtering could protect the silver film from oxidation. • Polyester fabric coated with Ag/ZnO composite film can obtained structural color. • The anti-ultraviolet and antistatic properties of polyester fabric coated with Ag/ZnO composite film all were good. - Abstract: Ag/ZnO composite film was successfully deposited on polyester fabric by using direct current (DC) magnetron sputtering and radio frequency (RF) magnetron reaction sputtering techniques with pure silver (Ag) and zinc (Zn) targets. X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD) were used to examine the deposited film on the fabric. It was found that the zinc film coated on Ag film before RF reactive sputtering could protect the silver film from oxidation. Anti-ultraviolet property and antistatic property of the coated samples using different magnetron sputtering methods were also investigated. The experimental results showed that Ag film was oxidized into in Ag{sub 2}O film in high vacuum oxygen environment. The deposition of Zn film on the surface of the fabric coated with Ag film before RF reactive sputtering, could successfully obtained Ag/ZnO composite film, and also generated structural color on the polyester fabric.

    11. Phenolic composition, antioxidant and anti-proliferative activities of edible and medicinal plants from the Peruvian Amazon

      Directory of Open Access Journals (Sweden)

      Jan Tauchen

      Full Text Available ABSTRACT Among 23 extracts of medicinal and edible plants tested, Mauritia flexuosa L.f., Arecaceae, showed significant antioxidant ability (DPPH and ORAC = 1062.9 and 645.9 ± 51.4 µg TE/mg extract, respectively, while Annona montana Macfad., Annonaceae, demonstrated the most promising anti-proliferative effect (IC50 for Hep-G2 and HT-29 = 2.7 and 9.0 µg/ml, respectively. However, combinatory antioxidant/anti-proliferative effect was only detected in Oenocarpus bataua Mart., Arecaceae (DPPH = 903.8 and ORAC = 1024 µg TE/mg extract; IC50 for Hep-G2 and HT-29 at 102.6 and 38.8 µg/ml, respectively and Inga edulis Mart., Fabaceae (DPPH = 337.0 and ORAC = 795.7 µg TE/mg extract; IC50 for Hep-G2 and HT-29 at 36.3 and 57.9 µg/ml, respectively. Phenolic content was positively correlated with antioxidant potential, however not with anti-proliferative effect. None of these extracts possessed toxicity towards normal foetal lung cells, suggesting their possible use in development of novel plant-based agents with preventive and/or therapeutic action against oxidative stress-related diseases.

    12. DPPH scavenging, PRAP activities and essential oil composition of edible Lathyrus ochrus L. (Cyprus Vetch, Luvana) from Cyprus.

      Science.gov (United States)

      Polatoğlu, Kaan; Arsal, Seniha; Demirci, Betül; Başer, Kemal Hüsnü Can

      2015-01-01

      The essential oil of the aerial parts of edible Lathyrus ochrus L. was investigated by simultaneous GC, GC/MS analyses under the same conditions. Trace amount of oil (0.01> mL) obtained by hydro distillation of 200 g fresh plants was trapped in 1 mL n-hexane. Twenty components were detected representing 91.55 ± 0.56 % of the oil. The main components were phytol 49.39 ± 0.44 %, hexadecanoic acid 20.64 ± 0.89 % and pentacosane 4.20 ± 0.09 %. Essential oil solution (1% oil: n-hexane) afforded similar DPPH scavenging activity (9.28 ± 1.30 %) when compared with positive controls α-tocopherol (9.74 ± 0.21 %) and BHT (7.79 ± 0.26 %) at the same concentrations. Antioxidant activity of the oil was determined using a new HPTLC-PRAP assay. The oil afforded two fold higher reducing activity of phosphomolybdenum complex (594.85 ± 5.14 AU) when compared with positive controls α- tocopherol (271.10 ± 2.86 AU) and BHT (210.53 ± 1.81 AU) at the same concentration.

    13. Nutritional composition and flavonoid content of edible wild greens and green pies: a potential rich source and antioxidant nutrients in the Mediterranean diet

      NARCIS (Netherlands)

      Trichopoulou, A.; Vasilopoulou, E.; Hollman, P.C.H.; Chamalides, Ch.; Foufa, E.

      2000-01-01

      The traditional Greek diet is dominated by the high consumption of olive oil, fruit and vegetables. Antioxidants represent a common element in these foods and may be important mediators of the beneficial effect of this diet. Wild edible greens are frequently consumed throughout Greece. Seven edible

    14. SiC fiber and yttria-stabilized zirconia composite thick thermal barrier coatings fabricated by plasma spray

      Science.gov (United States)

      Ma, Rongbin; Cheng, Xudong; Ye, Weiping

      2015-12-01

      Approximately 4 mm-thick SiC fiber/yttria-stabilized zirconia (YSZ) composite thermal barrier coatings (TBCs) were prepared by atmospheric plasma spray (APS). The composite coatings have a 'reinforced concrete frame structure', which can protect the coating from failure caused by increasing thickness of coating. The SiC fiber plays an important role in reducing the residual stress level of the composite coatings. The thermal conductivity (TC) value of the composite coatings is 0.632 W/m K, which is about 50% reduction compared to that of typical APS YSZ TBCs. And the composite coatings have higher fracture toughness and better thermal shock resistance than the YSZ TBCs.

    15. Minor lipophilic compounds in edible insects

      OpenAIRE

      Monika Sabolová; Anna Adámková; Lenka Kouřimská; Diana Chrpová; Jan Pánek

      2016-01-01

      Contemporary society is faced with the question how to ensure suffiecient nutrition (quantity and quality) for rapidly growing population. One solution can be consumption of edible insect, which can have very good nutritional value (dietary energy, protein, fatty acids, fibers, dietary minerals and vitamins composition). Some edible insects species, which contains a relatively large amount of fat, can have a potential to be a „good" (interesting, new) source of minor lipophilic compound...

    16. Molecular Composition and Ultrastructure of the Caveolar Coat Complex

      Science.gov (United States)

      Ludwig, Alexander; Howard, Gillian; Mendoza-Topaz, Carolina; Deerinck, Thomas; Mackey, Mason; Sandin, Sara; Ellisman, Mark H.; Nichols, Benjamin J.

      2013-01-01

      Caveolae are an abundant feature of the plasma membrane of many mammalian cell types, and have key roles in mechano-transduction, metabolic regulation, and vascular permeability. Caveolin and cavin proteins, as well as EHD2 and pacsin 2, are all present in caveolae. How these proteins assemble to form a protein interaction network for caveolar morphogenesis is not known. Using in vivo crosslinking, velocity gradient centrifugation, immuno-isolation, and tandem mass spectrometry, we determine that cavins and caveolins assemble into a homogenous 80S complex, which we term the caveolar coat complex. There are no further abundant components within this complex, and the complex excludes EHD2 and pacsin 2. Cavin 1 forms trimers and interacts with caveolin 1 with a molar ratio of about 1∶4. Cavins 2 and 3 compete for binding sites within the overall coat complex, and form distinct subcomplexes with cavin 1. The core interactions between caveolin 1 and cavin 1 are independent of cavin 2, cavin 3, and EHD2 expression, and the cavins themselves can still interact in the absence of caveolin 1. Using immuno-electron microscopy as well as a recently developed protein tag for electron microscopy (MiniSOG), we demonstrate that caveolar coat complexes form a distinct coat all around the caveolar bulb. In contrast, and consistent with our biochemical data, EHD2 defines a different domain at the caveolar neck. 3D electron tomograms of the caveolar coat, labeled using cavin-MiniSOG, show that the caveolar coat is composed of repeating units of a unitary caveolar coat complex. PMID:24013648

    17. Ti substrate coated with composite Cr–MoO2 coatings as highly selective cathode materials in hypochlorite production

      International Nuclear Information System (INIS)

      Lačnjevac, U.Č.; Jović, B.M.; Gajić-Krstajić, Lj.M.; Kovač, J.; Jović, V.D.; Krstajić, N.V.

      2013-01-01

      Highlights: ► Composite Cr–MoO 2 coatings were prepared by electrodeposition onto mild steel and Ti substrates. ► Ti/Cr–MoO 2 electrodes were investigated as cathode materials for the hypochlorite production. ► Selectivity of electrodes increased with the increase of the content of MoO 2 in the coating. ► The current efficiency for the HER exceeded 97% at the best cathode. ► The suppression of hypochlorite reduction is caused by the presence of Cr 2 O 3 at the surface. -- Abstract: The aim of this work was to investigate the possibility of preparation of the composite Cr–MoO 2 coatings onto steel and titanium substrates as cathode materials with high selective properties which imply the suppression of hypochlorite reduction as a side reaction during hypochlorite commercial production. The electrodes were prepared by simultaneous deposition of chromium and suspended MoO 2 particles on titanium substrate from acid chromium (VI) bath. The current efficiency for electrodeposition of the composite coatings did not vary significantly with the concentration of suspended MoO 2 particles. The content of molybdenum in the deposits was relatively low (0.2–1.5 at.%) and increased with increasing the concentration of suspended MoO 2 particles in the bath, in the range from 0 to 10 g dm −3 . With further increase in the concentration of MoO 2 , the content of molybdenum in the coating varied insignificantly. X-ray photoelectron spectroscopy-XPS and EDS analysis were applied to analyze elemental composition and chemical bonding of elements on the surface and in the sub-surface region of obtained coatings. When the concentration of MoO 2 particles in the bath was raised above 5 g dm −3 , the appearance of the coating changed from the typical pure chromium deposit to needle-like deposit with the appearance of black inclusions on the surface. XPS analysis and corresponding Cr 2p spectra showed the presence of chromium oxide, probably Cr 2 O 3 with Cr(3

    18. Tribological behavior of the carbon fiber reinforced polyphenylene sulfide (PPS) composite coating under dry sliding and water lubrication

      International Nuclear Information System (INIS)

      Xu Haiyan; Feng Zhizhong; Chen Jianmin; Zhou Huidi

      2006-01-01

      Carbon fiber reinforced polyphenylene sulphide (PPS) composite coatings (the mass fraction of the carbon fiber varied from 1 to 5 wt%) were prepared by flame spraying. The microstructure and physical properties of the composite coating were studied. The friction and wear characteristics of the PPS coating and carbon fiber reinforced PPS composite coating under dry- and water-lubricated sliding against stainless steel were comparatively investigated using a block-ring tester. The composite coatings showed lower friction coefficient and higher wear rate than pure PPS coatings under dry sliding. Under water-lubricated condition, the composite coatings showed better wear resistance than under dry. Under water-lubricated condition the tribological behaviors of the 3 wt% carbon fiber reinforced composite coating also were investigated under different sliding speed and load. The result showed that the sliding speed had little effect on the tribological properties, but the load affected greatly on that of the composite coatings. The morphologies of the worn surfaces of the composite coatings and the counterpart steel were analyzed by means of scanning electron microscopy (SEM), coupled with an energy-dispersive X-ray spectrometer (EDS) for compositional analysis

    19. High corrosion resistance of electroless composite plating coatings on AZ91D magnesium alloys

      International Nuclear Information System (INIS)

      Song, Y.W.; Shan, D.Y.; Han, E.H.

      2008-01-01

      The process of electroless plating Ni-P on AZ91D magnesium alloys was improved. The Ni-P-ZrO 2 composite coatings and multilayer coatings were investigated based on the new electroless plating process. The coatings surface and cross-section morphologies were observed with scanning electron microscopy (SEM). The chemical compositions were analyzed by EDXS. The corrosion behaviors were evaluated by immersion, salt spray and electrochemical tests. The experimental results indicated that the Ni-P-ZrO 2 composite coatings suffered attack in NaCl solution but displayed passivation characteristics in NaOH and Na 2 SO 4 solutions. The corrosion resistance of Ni-P-ZrO 2 coatings was superior to Ni-P coatings due to the effect of ZrO 2 nano-particle. The multilayer coatings consisting of Ni-P-ZrO 2 /electroplating nickel/Ni-P (from substrate to surface) can protect magnesium alloys from corroding more than 1000 h for the salt spray test

    20. Microstructure, optimum pigment content and low infrared emissivity of polyurethane/Ag composite coatings

      International Nuclear Information System (INIS)

      Zhang, Weigang; Xu, Guoyue; Ding, Ruya; Qiao, Jialiang; Duan, Kaige

      2013-01-01

      Polyurethane (PU)/Ag composite coatings with low infrared emissivity were successfully prepared by using PU and flaky Ag powders as adhesives and pigments, respectively. The infrared emissivity and microstructure of as-prepared products were systematically investigated by infrared emissometer and scanning electron microscopy, respectively. Infrared emissivity measurement shows that the emissivity of the coatings approaches the lowest value of 0.082 at the wavelength of 8–14 µm when the Ag content is about 20 wt%. Microstructure observation shows that the coatings have similar one-dimensional photonic structural characteristics. According to the structural characteristics, a simulation method for optimum pigment content and the cause of low infrared emissivity of the coatings were successfully obtained and discussed by using the theories of one-dimensional photonic structure, respectively. The results indicate that the low infrared emissivity of PU/Ag composite coatings is derived from the similar one-dimensional photonic structure in the coatings, and the calculated optimum Ag content is in good agreement with the experimental value, which reveals that it is a practical simulation method for optimum pigment content of low infrared emissivity composite coatings

    1. Microstructures and Properties of Laser Cladding Al-TiC-CeO2 Composite Coatings

      Science.gov (United States)

      Kong, Dejun; Song, Renguo

      2018-01-01

      Al-TiC-CeO2 composite coatings have been prepared by using a laser cladding technique, and the microstructure and properties of the resulting composite coatings have been investigated using scanning electron microscopy (SEM), a 3D microscope system, X-ray diffraction (XRD), micro-hardness testing, X-ray stress measurements, friction and wear testing, and an electrochemical workstation. The results showed that an Al-Fe phase appears in the coatings under different applied laser powers and shows good metallurgical bonding with the matrix. The dilution rate of the coating first decreases and then increases with increasing laser power. The coating was transformed from massive and short rod-like structures into a fine granular structure, and the effect of fine grain strengthening is significant. The microhardness of the coatings first decreases and then increases with increasing laser power, and the maximum microhardness can reach 964.3 HV0.2. In addition, the residual stress of the coating surface was tensile stress, and crack size increases with increasing stress. When the laser power was 1.6 kW, the coating showed high corrosion resistance. PMID:29373555

    2. Microstructures and Properties of Laser Cladding Al-TiC-CeO₂ Composite Coatings.

      Science.gov (United States)

      He, Xing; Kong, Dejun; Song, Renguo

      2018-01-26

      Al-TiC-CeO₂ composite coatings have been prepared by using a laser cladding technique, and the microstructure and properties of the resulting composite coatings have been investigated using scanning electron microscopy (SEM), a 3D microscope system, X-ray diffraction (XRD), micro-hardness testing, X-ray stress measurements, friction and wear testing, and an electrochemical workstation. The results showed that an Al-Fe phase appears in the coatings under different applied laser powers and shows good metallurgical bonding with the matrix. The dilution rate of the coating first decreases and then increases with increasing laser power. The coating was transformed from massive and short rod-like structures into a fine granular structure, and the effect of fine grain strengthening is significant. The microhardness of the coatings first decreases and then increases with increasing laser power, and the maximum microhardness can reach 964.3 HV 0.2 . In addition, the residual stress of the coating surface was tensile stress, and crack size increases with increasing stress. When the laser power was 1.6 kW, the coating showed high corrosion resistance.

    3. Characterization and properties of an advanced composite substrate for YBCO-coated conductors

      DEFF Research Database (Denmark)

      Gao, M.; Suo, H.; Zhao, Y.

      2010-01-01

      Thin, biaxially textured Ni5W/Ni12W/Ni5W composite substrates for coated conductor applications have been fabricated. The particularity of this three-layer composite configuration resides in the elemental diffusion between the outer layer and the core layer. Due to the migration of elemental W...

    4. Microdistribution of phases and substructure of the composite electrolytic self-lubricating copper-molybdenite coating

      International Nuclear Information System (INIS)

      Pribysh, I.Z.; Bakakin, G.N.; Borzyak, A.G.; Sajfullin, R.S.

      1978-01-01

      The influence of MoS 2 particles on the substructure of a copper matrix was studied, and their location in the composition was established. It is shown that the presence of molybdenite causes a variation in the conditions of electrical crystallization of copper. The optimum composition has been found, which is used as a self-lubricating coating for friction machine parts

    5. Chemical Composition and Antioxidant and Antibacterial Activities of an Essential Oil Extracted from an Edible Seaweed, Laminaria japonica L.

      Science.gov (United States)

      Patra, Jayanta Kumar; Das, Gitishree; Baek, Kwang-Hyun

      2015-07-02

      Laminaria japonica L. is among the most commonly consumed seaweeds in northeast Asia. In the present study, L. japonica essential oil (LJEO) was extracted by microwave-hydrodistillation and analyzed by gas chromatography and mass spectroscopy. LJEO contained 21 volatile compounds, comprising 99.76% of the total volume of the essential oil, primarily tetradeconoic acid (51.75%), hexadecanoic acid (16.57%), (9Z,12Z)-9,12-Octadecadienoic acid (12.09%), and (9Z)-hexadec-9-enoic acid (9.25%). Evaluation of the antibacterial potential against three foodborne pathogens, Bacillus cereus ATCC 10876, Escherichia coli O157:H7 ATCC 43890, and Staphylococcus aureus ATCC 49444, revealed that LJEO at a concentration of 25 mg/paper disc exerted high antibacterial activity against S. aureus (11.5 ± 0.58 mm inhibition zone) and B. cereus (10.5 ± 0.57 mm inhibition zone), but no inhibition of E. coli O157:H7. LJEO also displayed DPPH (1,1-diphenyl-2-picrylhydrazyl) free radical scavenging activity (80.45%), superoxide anion scavenging activity (54.03%), and ABTS (2,2'-azino-bis(3-ethylbenzothiazoline-6-sulphonic acid) radical and hydroxyl radical scavenging at 500 µg/mL. Finally, LJEO showed high inhibition of lipid peroxidation with strong reducing power. In conclusion, LJEO from edible seaweed is an inexpensive but favorable resource with strong antibacterial capacity as well as free radical scavenging and antioxidant activity; therefore, it has the potential for use in the food, cosmetics, and pharmaceutical industries.

    6. Chemical Composition and Antioxidant and Antibacterial Activities of an Essential Oil Extracted from an Edible Seaweed, Laminaria japonica L.

      Directory of Open Access Journals (Sweden)

      Jayanta Kumar Patra

      2015-07-01

      Full Text Available Laminaria japonica L. is among the most commonly consumed seaweeds in northeast Asia. In the present study, L. japonica essential oil (LJEO was extracted by microwave-hydrodistillation and analyzed by gas chromatography and mass spectroscopy. LJEO contained 21 volatile compounds, comprising 99.76% of the total volume of the essential oil, primarily tetradeconoic acid (51.75%, hexadecanoic acid (16.57%, (9Z,12Z-9,12-Octadecadienoic acid (12.09%, and (9Z-hexadec-9-enoic acid (9.25%. Evaluation of the antibacterial potential against three foodborne pathogens, Bacillus cereus ATCC 10876, Escherichia coli O157:H7 ATCC 43890, and Staphylococcus aureus ATCC 49444, revealed that LJEO at a concentration of 25 mg/paper disc exerted high antibacterial activity against S. aureus (11.5 ± 0.58 mm inhibition zone and B. cereus (10.5 ± 0.57 mm inhibition zone, but no inhibition of E. coli O157:H7. LJEO also displayed DPPH (1,1-diphenyl-2-picrylhydrazyl free radical scavenging activity (80.45%, superoxide anion scavenging activity (54.03%, and ABTS (2,2′-azino-bis(3-ethylbenzothiazoline-6-sulphonic acid radical and hydroxyl radical scavenging at 500 µg/mL. Finally, LJEO showed high inhibition of lipid peroxidation with strong reducing power. In conclusion, LJEO from edible seaweed is an inexpensive but favorable resource with strong antibacterial capacity as well as free radical scavenging and antioxidant activity; therefore, it has the potential for use in the food, cosmetics, and pharmaceutical industries.

    7. Friction and wear behavior of laser cladding Ni/hBN self-lubricating composite coating

      International Nuclear Information System (INIS)

      Zhang Shitang; Zhou Jiansong; Guo Baogang; Zhou Huidi; Pu Yuping; Chen Jianmin

      2008-01-01

      Ni/hBN coating was successfully prepared on 1Cr18Ni9Ti stainless steel substrate by means of laser cladding. The microhardness profile of the composite coating along the depth direction was measured, while its cross-sectional microstructures and phase compositions were analyzed by means of scanning electron microscopy and X-ray diffraction. Moreover, the friction and wear behavior of the composite coatings sliding against Si 3 N 4 from ambient to 800 deg. C was evaluated using a ball-on-disc friction and wear tester, and the worn surface morphologies of the composite coatings and counterpart ceramic balls were observed using a scanning electron microscope. At the same time, the worn surfaces of the ceramic balls were also analyzed using a 3D non-contact surface mapping profiler as well. It was found that the laser cladding Ni/hBN coating on the stainless steel substrate had high microhardness and good friction-reducing and antiwear abilities at elevated temperatures up to 800 deg. C. The composite coating registered slightly increased friction coefficient and wear rate as the temperature rose from ambient to 100 deg. C; then the friction coefficient and wear rate decreased with increasing temperature up to 800 deg. C (with the slight increase in the wear rate at 700 deg. C and 800 deg. C to be an exception). The laser cladding Ni/hBN coating was dominated by mixed adhesion and abrasive wear as it slid against the ceramic ball below 300 deg. C. With further increase in the test temperature up to 400 deg. C and above, it was characterized by mild adhesion wear and plastic deformation. Since the laser cladding Ni/hBN coating registered an increased wear rate at temperatures of 600 deg. C and above, it was not suggested to be used for wear prevention and protection of the stainless steel at elevated temperature above 800 deg. C

    8. Friction and wear behavior of laser cladding Ni/hBN self-lubricating composite coating

      Energy Technology Data Exchange (ETDEWEB)

      Zhang Shitang [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Graduate School, Chinese Academy of Sciences, Beijing 100039 (China); Zhou Jiansong [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Guo Baogang [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Graduate School, Chinese Academy of Sciences, Beijing 100039 (China); Zhou Huidi [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China); Pu Yuping [Central Iron and Steel Research Institute, Beijing 100081 (China); Chen Jianmin [State Key Laboratory of Solid Lubrication, Lanzhou Institute of Chemical Physics, Chinese Academy of Sciences, Lanzhou 730000 (China)], E-mail: chenjm@lzb.ac.cn

      2008-09-15

      Ni/hBN coating was successfully prepared on 1Cr18Ni9Ti stainless steel substrate by means of laser cladding. The microhardness profile of the composite coating along the depth direction was measured, while its cross-sectional microstructures and phase compositions were analyzed by means of scanning electron microscopy and X-ray diffraction. Moreover, the friction and wear behavior of the composite coatings sliding against Si{sub 3}N{sub 4} from ambient to 800 deg. C was evaluated using a ball-on-disc friction and wear tester, and the worn surface morphologies of the composite coatings and counterpart ceramic balls were observed using a scanning electron microscope. At the same time, the worn surfaces of the ceramic balls were also analyzed using a 3D non-contact surface mapping profiler as well. It was found that the laser cladding Ni/hBN coating on the stainless steel substrate had high microhardness and good friction-reducing and antiwear abilities at elevated temperatures up to 800 deg. C. The composite coating registered slightly increased friction coefficient and wear rate as the temperature rose from ambient to 100 deg. C; then the friction coefficient and wear rate decreased with increasing temperature up to 800 deg. C (with the slight increase in the wear rate at 700 deg. C and 800 deg. C to be an exception). The laser cladding Ni/hBN coating was dominated by mixed adhesion and abrasive wear as it slid against the ceramic ball below 300 deg. C. With further increase in the test temperature up to 400 deg. C and above, it was characterized by mild adhesion wear and plastic deformation. Since the laser cladding Ni/hBN coating registered an increased wear rate at temperatures of 600 deg. C and above, it was not suggested to be used for wear prevention and protection of the stainless steel at elevated temperature above 800 deg. C.

    9. Diffusion barrier coatings for high temperature corrosion resistance of advanced carbon/carbon composites

      International Nuclear Information System (INIS)

      Singh Raman, K.S.

      2000-01-01

      Carbon possesses an excellent combination of mechanical and thermal properties, viz., excellent creep resistance at temperatures up to 2400 deg C in non-oxidizing environment and a low thermal expansion coefficient. These properties make carbon a potential material for very high temperature applications. However, the use of carbon materials at high temperatures is considerably restricted due to their extremely poor oxidation resistance at temperatures above 400 deg C. The obvious choice for improving high temperature oxidation resistance of such materials is a suitable diffusion barrier coating. This paper presents an overview of recent developments in advanced diffusion- and thermal-barrier coatings for ceramic composites, with particular reference to C/C composites. The paper discusses the development of multiphase and multi-component ceramic coatings, and recent investigations on the oxidation resistance of the coated C/C composites. The paper also discusses the cases of innovative engineering solutions for traditional problems with the ceramic coatings, and the scope of intelligent processing in developing coatings for the C/C composites. Copyright (2000) AD-TECH - International Foundation for the Advancement of Technology Ltd

    10. Strontium and magnesium substituted dicalcium phosphate dehydrate coating for carbon/carbon composites prepared by pulsed electrodeposition

      Energy Technology Data Exchange (ETDEWEB)

      Liu, Shou-jie, E-mail: jlliushoujie@126.com; Li, He-jun, E-mail: lihejun@nwpu.edu.cn; Zhang, Lei-lei, E-mail: zhangleilei@nwpu.edu.cn; Feng, Lei, E-mail: fengleijinan@163.com; Yao, Pei, E-mail: 1113923884@qq.com

      2015-12-30

      Graphical abstract: The potentiodynamic polarization curve shows that the SM-DCPD coating can dramatically enhance the corrosion potential (E{sub corr}) value and meanwhile decrease the corrosion current density (I{sub corr}) of C/C composites. - Highlights: • Strontium and magnesium substituted dicalcium phosphate dehydrate coatings for carbon/carbon composites were synthesized by pulsed eletrodeposition. • Strontium and magnesium substituted dicalcium phosphate dehydrate coated carbon/carbon composites exhibited excellent bioactivity in vivo. • Strontium and magnesium substituted dicalcium phosphate dehydrate coated carbon/carbon composites showed lower corrosion rate with the comparison to pure carbon/carbon composites. - Abstract: Trace elements substituted apatite coatings have received a lot of interest recently as they have many benefits. In this work, strontium and magnesium substituted DCPD (SM-DCPD) coatings were deposited on carbon/carbon (C/C) composites by pulsed electrodeposition method. The morphology, microstructure, corrosion resistance and in vitro bioactivity of the SM-DCPD coatings are analyzed. The results show that the SM-DCPD coatings exhibit a flake-like morphology with dense and uniform structure. The SM-DCPD coatings could induce the formation of apatite layers on their surface in simulated body fluid. The electrochemical test indicates that the SM-DCPD coatings can evidently decrease the corrosion rate of the C/C composites in simulated body fluid. The SM-DCPD has potential application as the bioactive coatings.

    11. Improving the properties of mild steel by ternary multilayer composite coating via electrodeposition route

      Directory of Open Access Journals (Sweden)

      O. S.I. Fayomi

      2017-01-01

      Full Text Available A wide range of metal-oxides exhibit fascinating properties and multiple functionalities that could address challenge of physical and mechanical deterioration of materials in service. In this study, Zn-ZrO2, Zn-SiC and Zn-ZrO2-SiC composite coating was fabricated from zinc based sulphate electrolyte at constant current density, depth of immersion, distance between anode and cathode with time of deposition. The effect of particle on the physical behaviour of the coating was examined by coating gauge tester for the coating thickness and coating texture. The mechanical properties in term of hardness and wear characteristics were examined using high diamond micro-hardness tester and three body abrasive MTR-300 testers with dry sand rubber wheel apparatus with 5 N and 15 N, respectively. The coating stability in harsh region was examined with isothermal furnace at 200 oC for 4 h. The structural behaviour was investigated using scanning electron microscope attached with energy dispersion spectroscopy (SEM/EDS. The result shows that significant improvements in wear and hardness properties are linked to the microstructural modification of the coating as a result of the embedded particulate. The strengthening behaviour was improved with about 98% of coating efficiency. The progression of the coating thickness and texture were in line with other results obtained.

    12. POTENSI EDIBLE FILM ANTIMIKROBA SEBAGAI PENGAWET DAGING

      Directory of Open Access Journals (Sweden)

      Maskiyah (Maskiyah

      2015-06-01

      Full Text Available Fresh meat are highly perishable due to their enriched nutrient composition which is easily contaminated by almost any microorganisms. The application of antimicrobial edible films is one of the effective method to extend the shelf life of fresh meat. This study aimed to get antimicrobial edible films formula that have the potential to preserve fresh meat. The study consisted of several steps: 1 research for making a fresh garlic extract, 2 extraction of gelatin from chicken feet, 3 formulation and manufacturing of antimicrobial edible films and 4 the application of edible films on fresh meat. Gelatin-based antimicrobial edible films was the best one that can be applied on fresh meat. Characteristics of the antimirobial edible film: color L 97.28; elongation: 20 mm; tensile strength <0.1 kgf; thickness 0.06 mm; WVTR 15.49 g/(mm.jam; Aw 0.526; moisture content: 22.73%, and has antimicrobial characteristic because of it’s inhibition ability to the growth of S. aureus and E. coli. (Key words: Antimicrobial, Edible film, Meat

    13. Effect of active edible coatings made by basil seed gum and thymol on oil uptake and oxidation in shrimp during deep-fat frying.

      Science.gov (United States)

      Khazaei, Naimeh; Esmaiili, Mohsen; Emam-Djomeh, Zahra

      2016-02-10

      The effect of active coating treatments on oil uptake, moisture loss, lipid oxidation, texture, color, and sensory evaluation of shrimp after deep-fat frying process was investigated. Compared with the uncoated samples, coating treatments decreased the oil uptake and moisture loss of fried shrimp by 34.50 and 13.9%, respectively. Fried shrimp samples were analyzed for peroxide value (PV) and thiobarbituric acid (TBA). The most reduction in lipid oxidation (46.4% for PV and 40.8% for TBA) was observed when shrimp samples were coated with CS4 (containing 10% thyme), while the control samples had the highest values of PV and TBA after deep-fat frying process. Coated fried samples had significantly lower toughness and stiffness than control samples (P0.05). However, for the texture, juiciness, chewiness, and overall acceptability, coated fried samples had higher scores than control. Copyright © 2015 Elsevier Ltd. All rights reserved.

    14. Non-Cyanide Electrodeposited Ag–PTFE Composite Coating Using Direct or Pulsed Current Deposition

      Directory of Open Access Journals (Sweden)

      Raymond Sieh

      2016-07-01

      Full Text Available The effects of FC-4 cationic surfactant on electrodeposited Ag–PTFE composite coating using direct or pulsed currents were studied using scanning electron microscope (SEM, energy dispersive X-ray (EDS, optical microscope, and a linear tribometer. FC-4:PTFE in various ratios were added to a non-cyanide succinimide silver complex bath. Direct or pulsed current method was used at a constant current density to enable comparison between both methods. A high incorporation rate of PTFE was successfully achieved, with pulsed current being highly useful in increasing the amount of PTFE in the composite coating. The study of coating wear under sliding showed that a large majority of the electrodeposited coatings still managed to adhere to the substrate, even after 10 wear cycles of sliding tests. Performance improvements were achieved on all the samples with a coefficient of friction (CoF between 0.06 and 0.12.

    15. Tribaloy alloy reinforced tin-bronze composite coating for journal bearing applications

      International Nuclear Information System (INIS)

      Gao, F.; Liu, R.; Wu, X.J.

      2011-01-01

      This article presents an experimental study of the tribological behavior of a tin/bronze-based composite coating. The improved-ductility Tribaloy alloy (T-401) particles are selected as the reinforcement. This coating is made on the bushing of planet journals used in aerospace engines, deposited with the high velocity oxygen fuel (HVOF) thermal spray technique. The tribological properties such as friction and wear resistance of the coated bushing are investigated under the WAMsc3 Sliding Contact Test, along with the leaded tin/bronze bushing tested for comparison. The testing results show that the bushing coated with the composite exhibits superior tribological properties to the leaded tin/bronze bushing in that the former runs longer before the friction coefficient reaches 0.5 and also leads a to lower wear rate than the latter. The experimental results and wear mechanisms of these two bushings are discussed with the assistance of worn surface analyses using scanning electron microscopy (SEM).

    16. Composition, morphology and mechanical properties of sputtered TiAlN coating

      Energy Technology Data Exchange (ETDEWEB)

      Budi, Esmar, E-mail: esmarbudi@unj.ac.id [Department of Physics, Faculty of Science and Mathematics, Universitas Negeri Jakarta, Jl. Pemuda No. 10, Jakarta 13220 (Indonesia); Razali, M. Mohd. [Faculty of Manufacturing Engineering, Universiti Teknikal Malaysia Melaka, Karung Berkunci No. 1752 Pejabat Pos Durian Tunggal 76109 Melaka (Malaysia); Nizam, A. R. Md. [Faculty of Manufacturing Engineering, UniversitiTeknikal Malaysia Melaka, Karung Berkunci No. 1752 Pejabat Pos Durian Tunggal 76109 Melaka (Malaysia)

      2014-03-24

      TiAlN coating was deposited on the tungsten carbide cutting tool by using DC magnetron sputtering system to study the influence of substrate bias and nitrogen flow rate on the composition, morphology and mechanical properties. The negatively substrate bias and nitrogen flow rate was varied from about −79 to −221 V and 30 sccm to 72 sccm, respectively. The coating composition and roughness were characterized by using SEM/EDX and Atomic Force Microscopy (AFM), respectively. The dynamic ultra micro hardness tester was used to measure the mechanical properties. The coating hardness increases to about 10-12 GPa with an increase of the negatively substrate bias up to − 200 V and it tend to decrease with an increase in nitrogen flow rate up to 70 sccm. The increase of hardness follows the increase of Ti and N content and rms coating roughness.

    17. Use of Repeated Fluoropolymer Suspensions to Obtain Composite Electrochemical Coating Based on Zinc

      Science.gov (United States)

      Musikhina, T. A.; Zemtsova, E. A.; Fuks, C. L.

      2017-11-01

      This article deals with the issues of utilization of the waste products of fluoropolymers, namely, the suspensions of fluoroplasts that have lost their consumer properties. Such waste is recommended to be used as a filler of zinc coatings to provide increased corrosion resistance. Using the method of mathematical planning of the experiment, the authors establish the optimal compositions of galvanizing chloride-ammonium electrolytes to obtain the corrosion-resistant composite electrochemical coatings (CEC) of zinc-fluoropolymer. As a result, coatings with a finely crystalline structure were obtained differing in the distribution pattern on the surface of the samples and depending on the variation in the zinc concentration in the electrolytes. The samples of steel reinforcement with the zinc-fluoropolymer coating were tested on corrosion resistance. The increase of anticorrosive properties in CEC zinc-fluoropolymer and a slight decrease in microhardness were indicated.

    18. Annealing effects on magnetic properties of silicone-coated iron-based soft magnetic composites

      Science.gov (United States)

      Wu, Shen; Sun, Aizhi; Zhai, Fuqiang; Wang, Jin; Zhang, Qian; Xu, Wenhuan; Logan, Philip; Volinsky, Alex A.

      2012-03-01

      This paper focuses on novel iron-based soft magnetic composites synthesis utilizing high thermal stability silicone resin to coat iron powder. The effect of an annealing treatment on the magnetic properties of synthesized magnets was investigated. The coated silicone insulating layer was characterized by scanning electron microscopy and energy dispersive X-ray spectroscopy. Silicone uniformly coated the powder surface, resulting in a reduction of the imaginary part of the permeability, thereby increasing the electrical resistivity and the operating frequency of the synthesized magnets. The annealing treatment increased the initial permeability, the maximum permeability, and the magnetic induction, and decreased the coercivity. Annealing at 580 °C increased the maximum permeability by 72.5%. The result of annealing at 580 °C shows that the ferromagnetic resonance frequency increased from 2 kHz for conventional epoxy resin coated samples to 80 kHz for the silicone resin insulated composites.

    19. ELECTROPHORETIC DEPOSITION OF TIO2-MULTI-WALLED CARBON NANOTUBE COMPOSITE COATINGS: MORPHOLOGICAL STUDY

      Directory of Open Access Journals (Sweden)

      M. S. MAHMOUDI JOZEE

      2016-09-01

      Full Text Available A homogenous TiO2 / multi-walled carbon nanotubes(MWCNTs composite film were prepared by electrophoretic co-deposition from organic suspension on a stainless steel substrate.  In this study, MWCNTs was incorporated to the coating because of their long structure and their capability to be functionalized by different inorganic groups on the surface. FTIR spectroscopy showed the existence of carboxylic groups on the modified carbon nanotubes surface. The effect of applied electrical fields, deposition time and concentration of nanoparticulates on coatings morphology were investigated by scanning electron microscopy. It was found that combination of MWCNTs within TiO2 matrix eliminating micro cracks presented on TiO2 coating. Also, by increasing the deposition voltages, micro cracks were increased. SEM observation of the coatings revealed that TiO2/multi-walled carbon nanotubes coatings produced from optimized electric field was uniform and had good adhesive to the substrate.

    20. Composite Ni-Co-fly ash coatings on 5083 aluminium alloy

      Energy Technology Data Exchange (ETDEWEB)

      Panagopoulos, C.N., E-mail: chpanag@metal.ntua.gr [Laboratory of Physical Metallurgy, National Technical University of Athens, Zografos, 15780 Athens (Greece); Georgiou, E.P.; Tsopani, A.; Piperi, L. [Laboratory of Physical Metallurgy, National Technical University of Athens, Zografos, 15780 Athens (Greece)

      2011-03-15

      Ni-Co-fly ash coatings were deposited on zincate treated 5083 wrought aluminium alloy substrates with the aid of the electrodeposition technique. Structural and chemical characterization of the produced composite coatings was performed with the aid of X-ray diffraction (XRD), scanning electron microscopy (SEM) and electron dispersive X-ray analysis (EDS) techniques. The Ni-Co-fly ash coatings were found to consist of a crystalline Ni-Co solid solution with dispersed fly ash particles. In addition, chemical analysis of the Ni-Co matrix showed that it consisted of 80 wt.% Ni and 20 wt.% Co. The co-deposition of fly ash particles leads to a significant increase of the microhardness of the coating. The corrosion behaviour of the Ni-Co-fly ash/zincate coated aluminium alloy, in a 0.3 M NaCl solution (pH = 3.5), was studied by means of potentiodynamic corrosion experiments.

    1. Conservation of papaya minimally processed with the use of edible coating based on xanthan gum Conservação de mamão minimamente processado com uso de revestimento comestível à base de goma xantana

      Directory of Open Access Journals (Sweden)

      William Renzo Cortez-Vega

      2013-09-01

      Full Text Available The objective of this study was to evaluate the preservation of papaya minimally processed by the use of edible coatings based on xanthan gum for 12 days at 4±1 °C. Different treatments were performed: control (T1 uncoated; 1 % glycerol and 0.5 % xanthan gum (T2; 1 % glycerol, 0.5 % xanthan gum and 1 % chitosan (T3; 1 % glycerol, 0.5 % xanthan gum and 0.25 % guar gum (T4; 1 % glycerol, 0.5 % xanthan gum, 0.25 % guar gum and 1 % chitosan (T5. Such coatings were prepared in aqueous solution and added to them 1% glycerol. In the control treatment and the coated pieces of papaya were analyzed weight loss, firmness, pH, titratable acidity, color, and microbiological groups: psychrophilic, Salmonella spp., total coliform and thermotolerant. The different coatings based on xanthan gum were effective in preserving papaya minimally processed, relative to control sample. The addition of guar gum to xanthan coatings influenced negatively in the weight loss and the parameters of color, lightness, a* and b*. The addition of chitosan (T3 beneficially influence in reducing weight loss, maintenance of luminosity and a smaller reduction in parameters a* and b*, however, was not observed antimicrobial effect. Thus, it is suggested as an edible coatings papaya minimally processed coatings composed only xanthan gum (T2, which caused a reduction of weight loss, maintenance of lightness and b* and smaller reduction in a*. However, experiments aimed at maintaining firmness, pH and acidity should be conducted in future. Neste trabalho foi avaliada a conservação do mamão “Formosa” minimamente processado, com o uso de revestimento comestível à base de goma xantana, por 12 dias a 4±1 °C. Foram realizados os tratamentos: controle (T1, sem revestimento; revestimento com 0,5% de goma xantana (T2; revestimento com 0,5% de goma xantana e 1% de quitosana (T3; revestimento com 0,5% de goma xantana e 0,25% de goma guar (T4; revestimento com 0,5% de goma xantana, 0

    2. Electrophoretic deposition of chitosan/45S5 bioactive glass composite coatings doped with Zn and Sr

      Directory of Open Access Journals (Sweden)

      Marta eMiola

      2015-10-01

      Full Text Available In this research work the original 45S5 bioactive glass (BG was modified by introducing zinc and/or strontium oxide (6% mol in place of calcium oxide. Sr was added for its ability to stimulate bone formation, Zn for its role in bone metabolism, antibacterial properties and anti-inflammatory effect. The glasses were produced by means of melting and quenching process. SEM and XRD analyses evidenced that Zr and Sr introduction did not modify the glass structure and morphology, while compositional analysis (EDS demonstrated the effective addition of these elements inside the glass network. Bioactivity test in simulated body fluid (SBF up to one month evidenced a reduced bioactivity kinetics for Zn-doped glasses. Doped glasses were combined with chitosan to produce organic/inorganic composite coatings on stainless steel AISI 316L by electrophoretic deposition (EPD. Two EPD processes were considered for coating development, namely direct current EPD (DC-EPD and alternating current EPD (AC-EPD. The stability of the suspension was analysed and the deposition parameters were optimized. Tape and bending tests demonstrated a good coating-substrate adhesion for coatings containing 45S5-Sr and 45S5-ZnSr glasses, while the adhesion to the substrate decreased by using 45S5-Zn glass. FTIR analyses demonstrated the composite nature of coatings and SEM observations indicated that glass particles were well integrated in the polymeric matrix, the coatings were fairly homogeneous and free of cracks; moreover the AC-EPD technique provided better results than DC-EPD in terms of coating quality. SEM, XRD analyses and Raman spectroscopy, performed after bioactivity test in SBF solution, confirmed the bioactive behaviour of 45S5-Sr containing coating, while coatings containing Zn exhibited no hydroxyapatite formation.

    3. Characteristics of electrocodeposited Ni–Co–SiC composite coating

      Indian Academy of Sciences (India)

      Unknown

      improve the properties of coating further, Cr plating was also performed. Since the ... rectifier was used for d.c. current of 2 amp. After code- .... Table 2. Variation in hardness with volume fraction of SiC particles on the deposits as functions of.

    4. C/SiC/MoSi2-Si multilayer coatings for carbon/carbon composites for protection against oxidation

      International Nuclear Information System (INIS)

      Zhang Yulei; Li Hejun; Qiang Xinfa; Li Kezhi; Zhang Shouyang

      2011-01-01

      Highlights: → A C/SiC/MoSi 2 -Si multilayer coating was prepared on C/C by slurry and pack cementation. → Multilayer coating can protect C/C for 300 h at 1873 K or 103 h at 1873 K in air. → The penetration cracks in the coating result in the weight loss of the coated C/C. → The fracture of the coated C/C in wind tunnel result from the excessive local stress. - Abstract: To improve the oxidation resistance of carbon/carbon (C/C) composites, a C/SiC/MoSi 2 -Si multilayer oxidation protective coating was prepared by slurry and pack cementation. The microstructure of the as-prepared coating was characterized by scanning electron microscopy, X-ray diffraction and energy dispersive spectroscopy. The isothermal oxidation and erosion resistance of the coating was investigated in electrical furnace and high temperature wind tunnel. The results showed that the multilayer coating could effectively protect C/C composites from oxidation in air for 300 h at 1773 K and 103 h at 1873 K, and the coated samples was fractured after erosion for 27 h at 1873 K h in wind tunnel. The weight loss of the coated specimens was considered to be caused by the formation of penetration cracks in the coating. The fracture of the coated C/C composites might result from the excessive local stress in the coating.

    5. Preparation and characterization of the micro-arc oxidation composite coatings on magnesium alloys

      OpenAIRE

      Yanfeng Ge; Bailing Jiang; Ming Liu; Congjie Wang; Wenning Shen

      2014-01-01

      The magnesium alloys attract the light-weight manufacture due to its high strength to weight ratio, however the poor corrosion resistance limits the application in automobile industry. The Micro-arc Composite Ceramic (MCC) coatings on AZ91D magnesium alloys were prepared by Micro-arc Oxidation (MAO) and electrophoresis technologies. The microstructure, corrosion resistance, abrasion resistance, stone impact resistance and adhesion of MCC coatings were studied respectively. The cross section m...

    6. Ag-polytetrafluoroethylene composite coating on stainless steel as bipolar plate of proton exchange membrane fuel cell

      Energy Technology Data Exchange (ETDEWEB)

      Fu, Yu. [Laboratory of Fuel Cells, Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Zhongshan Road, Dalian 116023 (China); Graduate University of Chinese Academy of Sciences, Beijing 100049 (China); Hou, Ming; Shao, Zhigang; Yi, Baolian [Laboratory of Fuel Cells, Dalian Institute of Chemical Physics, Chinese Academy of Sciences, Zhongshan Road, Dalian 116023 (China); Xu, Hongfeng; Hou, Zhongjun; Ming, Pingwen [Sunrise Power Co., Ltd., Dalian 116025 (China)

      2008-08-01

      Forming a coating on metals by surface treatment is a good way to get high performance bipolar plate of proton exchange membrane fuel cell (PEMFC). In our research, Ag-polytetrafluoroethylene (PTFE) composite film was electrodeposited with silver-gilt solution of nicotinic acid by a bi-pulse electroplating power supply on 316 L stainless steel bipolar plate of PEMFC. Surface topography, contact angle, interfacial conductivity and corrosion resistance of the bipolar plate samples were investigated. Results showed that the defects on the Ag-PTFE composite coating are greatly reduced compared with those on the pure Ag coating fabricated under the same condition; and the contact angle of the Ag-PTFE composite coating with water is 114 , which is much bigger than that of the pure Ag coating (73 ). In addition, the interfacial contact resistance of the composite coating stays as low as the pure Ag coating; and the bipolar plate sample with composite coating shows a close corrosion resistance to the pure Ag coating sample in potentiodynamic and potentiostatic tests. Coated 316 L stainless steel plate with Ag-PTFE composite coating exhibits well hydrophobic characteristic, less defects, high interfacial conductivity and good corrosion resistance, which shows a great potential of the application in PEMFC. (author)

    7. Uptake of heavy metals in berries and edible fungi, and changes in the floral composition after treatment with ashes on forest soils

      International Nuclear Information System (INIS)

      Ruehling, Aa.

      1996-01-01

      Effects of treatment with ash on fungi and vascular plants, and on metal contents in berries and edible fungi, were studied in pine, spruce and birch forest stands in southern Sweden. Different types of ashes were studied. The changes to the vascular flora and the fungal flora that are today taking place in southern Sweden, and probably influenced by soil acidification and nitrogen deposition, are characterised by an impoverishment of mycorrhiza-forming species and thus cannot be corrected by supply of wood ashes. Instead, supply of at least raw ashes appears to hasten the process towards a nitrogen-favoured flora. It is known that raw ashes can cause nitrate-formation whereas granulated ashes have hardly increased the pH or lead to the formation of nitrate in any field experiment. The study has now been completed and has thus largely provided answers to the questions posed: Spreading of ashes does not lead to a general increase in the uptake of heavy metals in fungi and berries. The risk that berries and fungi will contain increased contents of heavy metals during the first season after spreading is small. The studies do not suggest that raw ashes can offer a short-term answer to counteracting the changes that are taking place to the composition of the fungal flora, probably as a result of soil acidification, or as a means of recreating conditions suitable for species requiring more alkaline conditions. 7 refs, 32 tabs

    8. Structure, phases, and mechanical response of Ti-alloy bioactive glass composite coatings

      Energy Technology Data Exchange (ETDEWEB)

      Nelson, G.M.; Nychka, J.A. [Department of Chemical and Materials Engineering, University of Alberta, 7th Floor, Electrical and Computer Engineering Research Facility, Edmonton, Alberta T6G 2V4 (Canada); McDonald, A.G., E-mail: andre2@ualberta.ca [Department of Mechanical Engineering, University of Alberta, 4-9 Mechanical Engineering Building, Edmonton, Alberta T6G 2G8 (Canada)

      2014-03-01

      Porous titanium alloy-bioactive glass composite coatings were manufactured via the flame spray deposition process. The porous coatings, targeted for orthodontic and bone-fixation applications, were made from bioactive glass (45S5) powder blended with either commercially pure titanium (Cp-Ti) or Ti-6Al-4V alloy powder. Two sets of spray conditions, two metallic particle size distributions, and two glass particle size distributions were used for this study. Negative control coatings consisting of pure Ti-6Al-4V alloy or Cp-Ti were sprayed under both conditions. The as-sprayed coatings were characterized through quantitative optical cross-sectional metallography, X-ray diffraction (XRD), and ASTM Standard C633 tensile adhesion testing. Determination of the porosity and glassy phase distribution was achieved by using image analysis in accordance with ASTM Standard E2109. Theoretical thermodynamic and heat transfer modeling was conducted to explain experimental observations. Thermodynamic modeling was performed to estimate the flame temperature and chemical environment for each spray condition and a lumped capacitance heat transfer model was developed to estimate the temperatures attained by each particle. These models were used to establish trends among the choice of alloy, spray condition, and particle size distribution. The deposition parameters, alloy composition, and alteration of the feedstock powder size distribution had a significant effect on the coating microstructure, porosity, phases present, mechanical response, and theoretical particle temperatures that were attained. The most promising coatings were the Ti-6Al-4V-based composite coatings, which had bond strength of 20 ± 2 MPa (n = 5) and received reinforcement and strengthening from the inclusion of a glassy phase. It was shown that the use of the Ti-6Al-4V-bioactive glass composite coatings may be a superior choice due to the possible osteoproductivity from the bioactive glass, the potential ability to

    9. A study of tribological behaviors of the phenolic composite coating reinforced with carbon fibers

      International Nuclear Information System (INIS)

      Song Haojie; Zhang Zhaozhu; Luo Zhuangzhu

      2007-01-01

      The nitric acid treatment was used as a method to bind acidic oxygen functional groups on carbon fiber surfaces, thereafter these fibers (CFO) and unmodified carbon fibers (CF) were incorporated into the phenolic composite coating for wear investigations. Surface analyses of the carbon fibers before and after treatments were performed by FTIR, X-ray photoelectron spectrometer (XPS). Tribological behaviors of carbon fibers filled phenolic coatings were investigated using a ring on block wear tests under dry friction condition, and the worn surfaces and the transfer films formed on the surface of counterpart ring were, respectively, studied by SEM and optical microscope. The results show that the additions of carbon fibers were able to reduce the friction coefficient of the phenolic coating and enhance the wear life of it, especially, the wear life of the phenolic coating was the best when content of carbon fibers is at 10 wt.%. Moreover, we found that the friction and wear behaviors of the phenolic coating reinforced with 10 wt.% CFO were better than those of the coating reinforced with 10 wt.% CF. FTIR and XPS analyses indicated that the oxygen functional groups, such as -OH, O-C=O, C=O, and C-O, were attached on the carbon fiber surfaces after the oxidated treatment. In both cases, appropriate treatments could effectively improve the mechanical and tribological properties in the phenolic composite coating due to the enhanced fiber-matrix interfacial bonding

    10. Development of Novel ECTFE Coated PP Composite Hollow-Fiber Membranes

      Directory of Open Access Journals (Sweden)

      Sergio Santoro

      2016-09-01

      Full Text Available In this work composite hollow-fibers were prepared by dip-coating of commercial polypropylene (PP with a thin layer of ethylene–chlorotrifluoroethylene copolymer (ECTFE. The employment of N-methyl pyrrolidone (NMP as solvent improved the polymer processability favoring dip-coating at lower temperature (135 °C. Scanning electron microscopy (SEM analyses showed that after dip-coating the PP support maintained its microstructure, whereas a thin coated layer of ECTFE on the external surface of the PP hollow-fiber was clearly distinguishable. Membrane characterization evidenced the effects of the concentration of ECTFE in the dope-solution and the time of dip-coating on the thickness of ECTFE layer and membrane properties (i.e., contact angle and pore size. ECTFE coating decreased the surface roughness reducing, as a consequence, the hydrophobicity of the membrane. Moreover, increasing the ECTFE concentration and dip-coating time enabled the preparation of a thicker layer of ECTFE with low and narrow pore size that negatively affected the water transport. On the basis of the superior chemical resistance of ECTFE, ECTFE/PP composite hollow fibers could be considered as very promising candidates to be employed in membrane processes involving harsh conditions.

    11. Electrophoretic deposition of hydroxyapatite-hexagonal boron nitride composite coatings on Ti substrate.

      Science.gov (United States)

      Göncü, Yapıncak; Geçgin, Merve; Bakan, Feray; Ay, Nuran

      2017-10-01

      In this study, commercial pure titanium samples were coated with nano hydroxyapatite-nano hexagonal boron nitride (nano HA-nano hBN) composite by electrophoretic deposition (EPD). The effect of process parameters (applied voltage, deposition time and solid concentration) on the coating morphology, thickness and the adhesion behavior were studied systematically and crack free nano hBN-nano HA composite coating production was achieved for developing bioactive coatings on titanium substrates for orthopedic applications. For the examination of structural and morphological characteristics of the coating surfaces, various complementary analysis methods were performed. For the structural characterization, XRD and Raman Spectroscopy were used while, Scanning Electron Microscopy (SEM) equipped with an energy dispersive spectrometer (EDS) and Transmission Electron Microscopy (TEM) techniques were carried out for revealing the morphological characterization. The results showed that nano HA-nano hBN were successfully deposited on Ti surface with uniform, crack-free coating by EPD. The amounts of hBN in suspension are considered to have no effect on coating thickness. By adding hBN into HA, the morphology of HA did not change and hBN has no significant effect on porous structure. These nanostructured surfaces are expected to be suitable for proliferation of cells and have high potential for bioactive materials. Copyright © 2017 Elsevier B.V. All rights reserved.

    12. Advanced Environmental Barrier Coating Development for SiC/SiC Ceramic Matrix Composites: NASA's Perspectives

      Science.gov (United States)

      Zhu, Dongming

      2016-01-01

      This presentation reviews NASA environmental barrier coating (EBC) system development programs and the coating materials evolutions for protecting the SiC/SiC Ceramic Matrix Composites in order to meet the next generation engine performance requirements. The presentation focuses on several generations of NASA EBC systems, EBC-CMC component system technologies for SiC/SiC ceramic matrix composite combustors and turbine airfoils, highlighting the temperature capability and durability improvements in simulated engine high heat flux, high pressure, high velocity, and with mechanical creep and fatigue loading conditions. The current EBC development emphasis is placed on advanced NASA 2700F candidate environmental barrier coating systems for SiC/SiC CMCs, their performance benefits and design limitations in long-term operation and combustion environments. Major technical barriers in developing environmental barrier coating systems, the coating integrations with next generation CMCs having the improved environmental stability, erosion-impact resistance, and long-term fatigue-environment system durability performance are described. The research and development opportunities for advanced turbine airfoil environmental barrier coating systems by utilizing improved compositions, state-of-the-art processing methods, and simulated environment testing and durability modeling are discussed.

    13. Protein-adsorption and Ca-phosphate formation on chitosan-bioactive glass composite coatings

      Science.gov (United States)

      Wagener, V.; Boccaccini, A. R.; Virtanen, S.

      2017-09-01

      In the last years, chitosan-bioactive glass (BG) composites have been developed and investigated as bioactive coatings for orthopedic applications. The increase of bioactivity occurs due to the stimulation of calcium-phosphate/hydroxyapatite formation on the surface while the coating is degrading. In the present work, protein adsorption and its influence on calcium-phosphate precipitation was studied for the first time on such composite coatings. The experiments involved coating of 316L stainless steel substrates with chitosan (Ch) and chitosan-bioactive glass (Ch-BG) and immersion of the coated samples in two different bovine serum albumin (BSA) containing solutions, namely DI H2O (with pH adjusted to about 7.2 with diluted NaOH) and simulated body fluid (SBF). In order to investigate the influence of protein adsorption on calcium-phosphate precipitation, samples were also immersed in DI H2O and in SBF without BSA. Samples were analyzed by scanning electron microscopy (SEM), X-ray photoelectron spectroscopy (XPS) and time-of-flight secondary ion mass spectrometry (ToF-SIMS). Surface analysis revealed that adsorption of BSA takes place on all studied samples and that protein adsorption is influenced by the presence of Ca2+ and PO43- ions. Bioactivity in the form of hydroxyapatite pre-stage formation is significantly increased on Ch-BG composite coating as compared with bare stainless steel surface. However, calcium-phosphate precipitation in SBF is reduced by the presence of BSA.

    14. Adhesion enhancement of Al coatings on carbon/epoxy composite surfaces by atmospheric plasma

      International Nuclear Information System (INIS)

      Coulon, J.F.; Tournerie, N.; Maillard, H.

      2013-01-01

      Adhesion strengths between aluminium thin film coatings and manufactured carbon/epoxy composite surfaces were measured by assessing fracture tensile strengths using pull-off tests. The effect of the substrate roughness (nm to μm) of these composite surfaces on adhesion was studied by examining the surface free energies and adhesion strengths. The adhesion strengths of the coatings varied significantly. To improve the coating adhesion, each composite surface was treated with atmospheric plasma prior to deposition, which resulted in an increase in the surface free energy from approximately 40 mJ/m 2 to 70 mJ/m 2 because the plasma pretreatment led to the formation of hydrophilic C-O and C=O bonds on the composite surfaces, as demonstrated by X-ray photoelectron spectroscopy analyses. The adhesion strengths of the coatings were enhanced for all surface roughnesses studied. In our study, the effect of mechanical adhesion due to roughness was separated from the effect of modifying the chemical bonds with plasma activation. The adhesion ability of the pure resin was relatively weak. Increasing the surface roughness largely improved the adhesion of the resin surface. Plasma treatment of the pure resin also increased the surface adhesion. Our study shows that plasma activation effectively enhances the adhesion of manufactured composites, even when the surface roughness is on the order of microns. The ageing of the surface activation was also investigated, and the results demonstrate that atmospheric plasma has potential for use in the pretreatment of composite materials.

    15. Preparation and Characterization of Pyrotechnics Binder-Coated Nano-Aluminum Composite Particles

      Science.gov (United States)

      Ye, Mingquan; Zhang, Shuting; Liu, Songsong; Han, Aijun; Chen, Xin

      2017-07-01

      The aim of this article is to protect the activity of nano-aluminum (Al) particles in solid rocket propellants and pyrotechnics. The morphology, structure, active aluminum content, and thermal and catalytic properties of the coated samples were characterized by scanning electron microscopy (SEM), transmission electron microscopy (TEM), Fourier transform infrared spectroscopy (FTIR), thermogravimetry-differential scanning calorimetry (TG-DSC), and oxidation-reduction titration methods. The results indicated that nano-Al particles could be effectively coated with phenolic resin (PF), fluororubber (Viton B), and shellac through a solvent/nonsolvent method. The energetic composite particles have core-shell structures and the thickness of the coating film is about 5-15 nm. Analysis of the active Al content revealed that Viton B coating had a much better protective effect. The TG-DSC results showed that the energy amount and energy release rate of PF-, Viton B-, and shellac-coated Al particles were larger than those of the raw nano-Al particles. The catalytic effects of coated Al particles on the thermal decomposition of ammonium perchlorate (AP) were better than those of raw nano-Al particles, and the effect of shellac-coated Al particles was significantly better than that of Viton B-coated Al particles.

    16. Evaluation of magnetostrictive composite coated fabric as a fragment barrier material

      International Nuclear Information System (INIS)

      Son, Kwon Joong; Fahrenthold, Eric P

      2012-01-01

      Over the last decade a surge in fragment barrier research has led to investigation of numerous materials and material augmentations in the attempt to improve the ballistic performance of systems designed to protect personnel, vehicles or infrastructure from impact and blast loads. One widely studied material augmentation approach is the use of coatings, often polymers, to enhance the performance of protection systems constructed from metal, concrete, composite and fabric materials. In recent research the authors have conducted the first experimental study of the ballistic performance of fabrics coated with a magnetically responsive polymer. Zero field impact experiments on coated fabric targets showed a 61% increase in impact energy dissipation, although the coated targets were not competitive with neat fabrics on a protection per unit mass basis. Under an applied field of 110 kA m −1 , the ballistic performance of the coated fabric was reduced. The reduction in performance may be attributed to a reduction in material damping and an increase in material modulus for the magnetostrictive component of the coating. Analysis of the coated fabric response to magnetic preloads suggests that coating tensile stresses and coating–fabric interface stresses induced by the applied field may also adversely affect ballistic performance. (paper)

    17. Effects of composite surface coating and pre-drying on the properties of kabanosy dry sausage.

      Science.gov (United States)

      Tyburcy, Andrzej; Kozyra, Daniel

      2010-10-01

      Coating of dry sausages with renewable materials could be an alternative to vacuum packaging. In this study kabanosy dry sausage was coated with a composite emulsion and stored for 7 or 15 days at 4-6 degrees C. Effects of different emulsion formulas (0.5 or 1% w/w of kappa-carrageenan and 5 or 10% w/w of glycerol) and pre-drying of coated sausages (at 50 degrees C for 1.5h) were investigated. Carrageenan concentration had a significant effect (Pemulsion adsorbed on the sausage surface but little influence on the barrier properties of the coatings. At both glycerol concentration levels, coatings had no visible cracks and were easily removed from the sausage surface after 7 and 15 days of storage. The colour values of coatings (L*, a*, and b*) changed along with the decreasing water activity during storage. Pre-drying of coated sausages reduced peeled product weight loss after storage. The financial analysis showed that among coatings tested the best proved to be the emulsion containing (w/w): 5% glycerol, 5% gelatin, 0.5% carrageenan, 20% lard, 20% beeswax, and 50% water. Copyright (c) 2010 The American Meat Science Association. Published by Elsevier Ltd. All rights reserved.

    18. Measurement of residual stress in plasma-sprayed metallic, ceramic and composite coatings

      Energy Technology Data Exchange (ETDEWEB)

      Kesler, O.; Suresh, S. [Massachusetts Inst. of Tech., Cambridge, MA (United States); Matejicek, J.; Sampath, S. [State Univ. of New York, Stony Brook, NY (United States). Inst. for Mathematical Sciences; Gnaeupel-Herold, T.; Brand, P.C.; Prask, H.J. [National Institute of Standards and Technology, Gaithersburg, MD (United States)

      1998-12-15

      Residual stresses in plasma-sprayed coatings were studied by three experimental techniques: curvature measurements, neutron diffraction and X-ray diffraction. Two distinct material classes were investigated: (1) single-material coatings (molybdenum) and (2) bi-material composites (nickel+alumina and NiCrAlY+yttria-stabilized zirconia), with and without graded layers. This paper deals with the effects of coating thickness and material properties on the evolution of residual stresses as a function of composition and thickness in both homogeneous and graded coatings. Mathematical analysis of the results allowed in some cases the separation of the quenching stress and thermal stress contributions to the final residual stress, as well as the determination of the through-thickness stress profile from measurements of different thickness specimens. In the ceramic-metal composites, it was found that the quenching stress plays a dominant role in the metallic phase, whereas the stress in the ceramic phase is mostly dominated by thermal mismatch. The respective thermal expansion coefficients and mechanical properties are the most important factors determining the stress sign and magnitude. The three residual stress measurement methods employed here were found to be complementary, in that each can provide unique information about the stress state. The most noteworthy outcomes are the determination of the through-thickness stress profile in graded coatings with high spatial resolution (curvature method) and determination of stress in each phase of a composite separately (neutron diffraction). (orig.) 25 refs.

    19. Organic composite-mediated surface coating of human acellular bone matrix with strontium.

      Science.gov (United States)

      Huang, Yi-Zhou; Wang, Jing-Jing; Huang, Yong-Can; Wu, Cheng-Guang; Zhang, Yi; Zhang, Chao-Liang; Bai, Lin; Xie, Hui-Qi; Li, Zhao-Yang; Deng, Li

      2018-03-01

      Acellular bone matrix (ACBM) provides an osteoconductive scaffold for bone repair, but its osteoinductivity is poor. Strontium (Sr) improves the osteoinductivity of bone implants. In this study, we developed an organic composite-mediated strontium coating strategy for ACBM scaffolds by using the ion chelating ability of carboxymethyl cellulose (CMC) and the surface adhesion ability of dopamine (DOPA). The organic coating composite, termed the CMC-DOPA-Sr composite, was synthesized under a mild condition, and its chemical structure and strontium ion chelating ability were then determined. After surface decoration, the physicochemical properties of the strontium-coated ACBM (ACBM-Sr) scaffolds were characterized, and their biocompatibility and osteoinductivity were determined in vitro and in vivo. The results showed that the CMC-DOPA-Sr composite facilitated strontium coating on the surface of ACBM scaffolds. The ACBM-Sr scaffolds possessed a sustained strontium ion release profile, exhibited good cytocompatibility, and enhanced the osteogenic differentiation of mesenchymal stem cells in vitro. Furthermore, the ACBM-Sr scaffolds showed good histocompatibility after subcutaneous implantation in nude mice. Taken together, this study provided a simple and mild strategy to realize strontium coating for ACBM scaffolds, which resulted in good biocompatibility and improved osteoinductivity. Copyright © 2017 Elsevier B.V. All rights reserved.

    20. Preparation and properties of electrodeposited Ni-TiO2 composite coating

      Directory of Open Access Journals (Sweden)

      Sukhdev Singh Bhogal

      2015-03-01

      Full Text Available Mechanical properties of cutting tool like microhardness, coating adhesiveness & corrosion resistance are some important parameters, which affects the tool life and further indirectly affects the component cost. In this paper Ni-TiO2 composite coating was prepared through electrocodeposition in order to improve the mechanical properties of tungsten carbide cutting tools. Microhardness of Ni-TiO2 composite layer have been studied by varying input current density (mA, pH vale of electrolyte & particle concentration of TiO2 in electrolyte bath. Microstructure and phase structure of composite layer were investigated using atomic force microscope (AFM, scanning electronic microscope (SEM and X-ray diffraction (XRD. Surface morphology of Ni-TiO2 coated layer shows fine grained structures is obtained at low currents with higher microhardness of composite coating. Maximum microhardness 1483 HV of coated layer is found at 15mA of current and at 4.5 pH of watt’s solution. It has also been seen that with the increase of Ti, microhardness of the layer is also increases.  

    1. Biocompatibility of sol-gel hydroxyapatite-titania composite and bilayer coatings

      Energy Technology Data Exchange (ETDEWEB)

      Sidane, D., E-mail: dj.sidane@yahoo.fr [Laboratoire de Génie de l' Environnement (LGE), Faculté de Technologie, Université de Bejaia, 06000, Bejaia (Algeria); Rammal, H. [Equipe d' Accueil 4691 Biomatériaux et Inflammation en Site Osseux, SFR-CAP Santé (FED 4231), Université de Reims Champagne Ardenne, 1 Avenue du Maréchal Juin, 51100 Reims (France); Beljebbar, A. [UMR CNRS 7369, Equipe MéDIAN Biophotonique et Technologies pour la Santé, UFR de Pharmacie, SFR-CAP Santé (FED 4231), Université de Reims Champagne Ardenne, 51 rue Cognacq-Jay, 51096 Reims (France); Gangloff, S.C. [Equipe d' Accueil 4691 Biomatériaux et Inflammation en Site Osseux, SFR-CAP Santé (FED 4231), Université de Reims Champagne Ardenne, 1 Avenue du Maréchal Juin, 51100 Reims (France); Chicot, D. [FRE 3723 - LML - Laboratoire de Mécanique de Lille, Univ. Lille, 59000 Lille (France); Velard, F. [Equipe d' Accueil 4691 Biomatériaux et Inflammation en Site Osseux, SFR-CAP Santé (FED 4231), Université de Reims Champagne Ardenne, 1 Avenue du Maréchal Juin, 51100 Reims (France); Khireddine, H. [Laboratoire de Génie de l' Environnement (LGE), Faculté de Technologie, Université de Bejaia, 06000, Bejaia (Algeria); and others

      2017-03-01

      Titania-Hydroxyapatite (TiO{sub 2}/HAP) reinforced coatings are proposed to enhance the bioactivity and corrosion resistance of 316L stainless steel (316L SS). Herein, spin- and dip-coating sol-gel processes were investigated to construct two kinds of coatings: TiO{sub 2}/HAP composite and TiO{sub 2}/HAP bilayer. Physicochemical characterization highlighted the bioactivity response of the TiO{sub 2}/HAP composite once incubated in physiological conditions for 7 days whereas the TiO{sub 2}/HAP bilayer showed instability and dissolution. Biological analysis revealed a failure in human stem cells adhesion on TiO{sub 2}/HAP bilayer whereas on TiO{sub 2}/HAP composite the presence of polygonal shaped cells, possessing good behaviour attested a good biocompatibility of the composite coating. Finally, TiO{sub 2}/HAP composite with hardness up to 0.6 GPa and elastic modulus up to 18 GPa, showed an increased corrosion resistance of 316L SS. In conclusion, the user-friendly sol-gel processes led to bioactive TiO{sub 2}/HAP composite buildup suitable for biomedical applications. - Highlights: • 316L SS implant TiO{sub 2} reinforced HAP coatings were investigated and compared. • TiO{sub 2}/HAP composite had better structural features and biocompatible properties. • Improvement of 316L SS implants corrosion resistance. • TiO{sub 2}/HAP composite mechanical properties close to bone tissue • Low cost and desired material for hard tissue applications.

    2. Biomimetically-mineralized composite coatings on titanium functionalized with gelatin methacrylate hydrogels

      Energy Technology Data Exchange (ETDEWEB)

      Tan, Guoxin, E-mail: tanguoxin@126.com [School of Chemical Engineering and Light Industry, Guangdong University of Technology, Guangzhou, 510006 (China); Zhou, Lei [School of Chemical Engineering and Light Industry, Guangdong University of Technology, Guangzhou, 510006 (China); Ning, Chengyun, E-mail: imcyning@scut.edu.cn [College of Materials Science and Technology, South China University of Technology, Guangzhou, 510641 (China); Tan, Ying [School of Chemical Engineering and Light Industry, Guangdong University of Technology, Guangzhou, 510006 (China); Ni, Guoxin [Department of Orthopedics and Traumatology, Nanfang Hospital, Southern Medical University, Guangzhou, 510515 (China); Liao, Jingwen; Yu, Peng; Chen, Xiaofeng [College of Materials Science and Technology, South China University of Technology, Guangzhou, 510641 (China)

      2013-08-15

      Immobilizing organic–inorganic hybrid composites onto the implant surface is a promising strategy to improve host acceptance of the implant. The objective of this present study was to obtain a unique macroporous titanium-surface with the organic–mineral composite coatings consisting of gelatin methacrylate hydrogel (GelMA) and hydroxyapatite (HA). A 3-(trimethoxysilyl) propyl methacrylate (TMSPMA) layer was first coated onto the titanium surface, and surface was then covalently functionalized with GelMA using a photochemical method. Mineralization of the GelMA coating on the titanium surface was subsequently carried out by a biomimetic method. After 3-day mineralization, a large number of mineral phases comprising spherical amorphous nanoparticles were found randomly deposited inside GelMA matrix. The resulting mineralized hydrogel composites exhibited a unique rough surface of macroporous structure. The structure of the prepared GelMA/HA composite coating was studied by field emission scanning electron microscopy (FESEM), energy dispersive X-ray spectra (EDS), attenuated total refraction Fourier transform infrared spectroscopy (ATR-FTIR), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD). Water contact angle measurement revealed the hydrophilicity properties of composite coatings. GelMA/HA on titanium after the TMSPMA treatment is very stable when tested in vitro with a PBS solution at 37 °C, due to the role of TMSPMA as a molecular bridge. It was expected that the macroporous GelMA/HA composite coatings might potentially promote and accelerate titanium (Ti)-based implants osseointegration for bone repair and regeneration.

    3. Effect of Gelatin-Based Edible Coatings Incorporated with Aloe vera and Black and Green Tea Extracts on the Shelf Life of Fresh-Cut Oranges

      Directory of Open Access Journals (Sweden)

      Mohsen Radi

      2017-01-01

      Full Text Available The aim of this study was to evaluate the effect of gelatin coating incorporated with Aloe vera gel (50,100% and green and black tea extracts (5,10% on physicochemical, microbial, and sensorial properties of fresh-cut oranges at 4°C for 17 days. Significant differences in terms of quality parameters were observed between the control and coated fresh-cut oranges. The highest variation of quality parameters was observed in control, while the least variations were observed in coated slices with 100% Aloe vera and 10% green tea extract. The weight loss was increased with time, but the coating treatment especially with 100% Aloe vera had significant effect on the prevention of weight loss. Also, Aloe vera coated samples obtained the highest score in sensory evaluation. Coating with gelatin incorporated with Aloe vera and green tea extracts successfully retarded the microbial growth and therefore extended the shelf life of fresh-cut oranges during cold storage.

    4. Improving composition of protective coatings for steel casting

      International Nuclear Information System (INIS)

      Kuz'kina, N.N.; Pegov, V.G.; Bogatenkov, V.F.; Shub, L.G.; Raspopova, N.A.

      1983-01-01

      A radically new fuel-free slag-forming mixture used as protective coating for steel casting is introduced. The lack of combustible powders precludes explosion and fire Lazard in mixture preparation. Usage of the new mixture in stainless steel casting of Kh18N10T type permitted to improve the ingot surface quality and reduce spoilage from 1.16 to 0.66%

    5. Preparation and properties of in-situ growth of carbon nanotubes reinforced hydroxyapatite coating for carbon/carbon composites

      Energy Technology Data Exchange (ETDEWEB)

      Liu, Shoujie, E-mail: jlliushoujie@126.com; Li, Hejun, E-mail: lihejun@nwpu.edu.cn; Su, Yangyang, E-mail: suyangyang@mail.nwpu.edu.cn; Guo, Qian, E-mail: 1729299905@163.com; Zhang, Leilei, E-mail: zhangleilei@nwpu.edu.cn

      2017-01-01

      Carbon nanotubes (CNTs) possess excellent mechanical properties for their role playing in reinforcement as imparting strength to brittle hydroxyapatite (HA) bioceramic coating. However, there are few reports relating to the in-situ grown carbon nanotubes reinforced hydroxyapatite (CNTs-HA) coating. Here we demonstrate the potential application in reinforcing biomaterials by an attempt to use in-situ grown of CNTs strengthen HA coating, using a combined method composited of injection chemical vapor deposition (ICVD) and pulsed electrodeposition. The microstructure, phases and chemical compositions of CNTs-HA coatings were characterized by various advanced methods. The scanning electron microscopy (SEM) images indicated that CNTs-HA coatings avoided the inhomogeneous dispersion of CNTs inside HA coating. The result show that the interfacial shear strength between CNTs-HA coating and the C/C composite matrix reaches to 12.86 ± 1.43 MPa. Potenitodynamic polarization and electrochemical impedance spectroscopy (EIS) studies show that the content of CNTs affects the corrosion resistance of CNTs-HA coating. Cell culturing and simulated body fluid test elicit the biocompatibility with living cells and bioactivity of CNTs-HA coatings, respectively. - Highlights: • A novel bioceramic composite coating of hydroxyapatite reinforced with in-situ grown carbon nanotubes was fabricated. • The doping of carbon nanotubes had almost no impact on the biocompatibility of hydroxyapatite coatings. • The doping of carbon nanotubes improved corrosion resistance of hydroxyapatite coatings in simulated human body solution.

    6. ELASTO-PLASTIC DEFORMATION OF COMPOSITE POWDERS WITH LAYERED CARBON AND CARBIDE-FORMING ELEMENT COATING

      Directory of Open Access Journals (Sweden)

      V. N. Kovalevsky

      2012-01-01

      Full Text Available Coating structure formation under magnetron spraying of titanium and carbon cathodes and combined cathodes, namely cobalt (EP 131 – nickel, tungsten – carbon have been investigated under conditions of carbide separate synthesis within the temperature range of 650–1200 °C. Usage of cobalt and nickel particles as matrix material leads to their rapid thermal expansion under heating during sintering process in the dilatometer. Subsequent plastic deformation of sintered samples provides obtaining a composite powder material that is a composite with framing structure of cobalt, titanium and tungsten carbides in the coatings.

    7. Thermomechanical and Environmental Durability of Environmental Barrier Coated Ceramic Matrix Composites Under Thermal Gradients

      Science.gov (United States)

      Zhu, Dongming; Bhatt, Ramakrishna T.; Harder, Bryan

      2016-01-01

      This paper presents the developments of thermo-mechanical testing approaches and durability performance of environmental barrier coatings (EBCs) and EBC coated SiCSiC ceramic matrix composites (CMCs). Critical testing aspects of the CMCs will be described, including state of the art instrumentations such as temperature, thermal gradient, and full field strain measurements; materials thermal conductivity evolutions and thermal stress resistance; NDE methods; thermo-mechanical stress and environment interactions associated damage accumulations. Examples are also given for testing ceramic matrix composite sub-elements and small airfoils to help better understand the critical and complex CMC and EBC properties in engine relevant testing environments.

    8. DETERMINATION OF PHASE COMPOSITION OF SEALING COATING BASED ON APC (ALUMINOPHOSPHATE COMPOUNDS

      Directory of Open Access Journals (Sweden)

      BOLSHAKOV V. I.

      2017-02-01

      Full Text Available Summary. Goal. To investigate the phase composition of the obtained sealing coatings based on aluminophosphate compound (APC and the impact of temperature rise on it. Methods. Qualitative X-ray phase analysis (XRPA and differential thermal analysis (DTA are used as the methods of research. Roentgenograms for structural analysis were obtained on a DRON-4-07 using filtered copper radiation in the secondary beam. Registration and initial processing of diffraction patterns was performed using the software package PDOS with the output of the diffraction patterns on the screen. Using the "loupe" option allowed to identify weak interference lines, which increased the accuracy of the method of qualitative XRPA. The thermograms for DTA received on the device type Termoskan-2. The results. It is revealed that base of coating is X-ray amorphous phase. There are following crystalline phases: Al, AlPO4, Al (PO3 3, BN found in the coating. It is revealed that annealing doesn’t make a significant influence on the phase composition of the crystalline phases and the coating doesn’t lose properties after annealing during repeated thermal stress. Scientific novelty. The phase composition of the proposed sealing coatings based on APC and produced by plasma spraying, and the effect of annealing on the phase composition of the coating are investigated. The reaction of synthesis of primary material forming on the basis of APC for coating is offered. Practical significance. The results can be used in aviation technology in the development of gas turbine engines (GTE and the design of the compressors. The sealing coating may be used to improve the reliability of the compressor and to increase the efficiency ratio of turbine engine. During the operation the compressor’s blades touch the sealing coating of compressor’s stator and grooves it without causing locking and destruction of the rotor. Therefore, the development of new sealing coating compositions that

    9. Characterisation of the Microstructure of Fe–Al/Cr3C2 Composite Coatings

      Science.gov (United States)

      Liu, Xiaoming; JunhuiDong; Yang, Yuehong; Sun, Changming; Tuo, Ya; Li, Yanwei

      2018-03-01

      An Fe-Al/Cr3C2 composite coating is investigated to assess its suitability for treating high-temperature components in a power plant. The coating exhibits excellent high- temperature properties including good corrosion, erosion and friction-wear resistance at high temperatures. To deduce the formation of the Fe-Al/Cr3C2 composite coating and to provide an adequate theoretical basis for its extensive application, its structures and microstructures are investigated. Scanning electronic microscopy (SEM)is used along with energy-dispersive X-ray analysis (EDAX) to analyse the surface of the coating. Energy-dispersive spectroscopy (EDS) is used to analyse the cross-section of the coating. Further, X-ray diffraction (XRD) and transmission electron microscopy (TEM) are used to analyse the phases and micro structural features within the coating. The results reveal that the basic phases are two orderly inter metallic compounds (Fe3Al and FeAl) and that the reinforcement includes two oxides (Al2O3 and Cr2O3) as well as substantial quantities of Cr3C2. Al2O3is formed using two mechanisms: oxidation of aluminium in the coating and separation of Al2O3crystals from Fe3Al and FeAl. The grain size of Al2O3 and Cr2O3 in the coatings is nanometric. These two oxides may increase the corrosion-erosion and wear resistances of the coating when they are used as reinforcements.

    10. The effect of composition and thermodynamics on the surface morphology of durable superhydrophobic polymer coatings

      Directory of Open Access Journals (Sweden)

      Nahum T

      2017-02-01

      Full Text Available Tehila Nahum,1 Hanna Dodiuk,2 Samuel Kenig,2 Artee Panwar,1 Carol Barry,1 Joey Mead,1 1Department of Plastics Engineering, University of Massachusetts Lowell, Lowell, MA, USA; 2Department of Polymers and Plastics Engineering, Shenkar College of Engineering Design and Art, Ramat Gan, Israel Abstract: Durable superhydrophobic coatings were synthesized using a system of silica nanoparticles (NPs to provide nanoscale roughness, fluorosilane to give hydrophobic chemistry, and three different polymer binders: urethane acrylate, ethyl 2-cyanoacrylate, and epoxy. Coatings composed of different binders incorporating NPs in various concentrations exhibited different superhydrophobic attributes when applied on polycarbonate (PC and glass substrates and as a function of coating composition. It was found that the substrate surface characteristics and wettability affected the superhydrophobic characteristics of the coatings. Interfacial tension and spreading coefficient parameters (thermodynamics of the coating components were used to predict the localization of the NPs for the different binders’ concentrations. The thermodynamic analysis of the NPs localization was in good agreement with the experimental observations. On the basis of the thermodynamic analysis and the experimental scanning electron microscopy, X-ray photoelectron spectroscopy, profilometry, and atomic force microscopy results, it was concluded that localization of the NPs on the surface was critical to provide the necessary roughness and resulting superhydrophobicity. The durability evaluated by tape testing of the epoxy formulations was the best on both glass and PC. Several coating compositions retained their superhydrophobicity after the tape test. In summary, it was concluded that thermodynamic analysis is a powerful tool to predict the roughness of the coating due to the location of NPs on the surface, and hence can be used in the design of superhydrophobic coatings. Keywords

    11. Beneficial effects of laser irradiation on the deposition process of diamond/Ni60 composite coating with cold spray

      Energy Technology Data Exchange (ETDEWEB)

      Yao, Jianhua, E-mail: laser@zjut.edu.cn; Yang, Lijing; Li, Bo; Li, Zhihong

      2015-03-01

      Graphical abstract: - Highlights: • The hard Ni-based alloy powder as matrix in diamond composite coating was studied. • The influence of laser on diamond distribution of composite coating was analyzed. • The graphitization of diamond was prohibited in supersonic laser deposition process. • The abrasion mechanisms of diamond/Ni60 composite coating were discussed. - Abstract: Although cold spray process has many unique advantages over other coating techniques, it has difficulties in depositing hard materials. This article presents a study in the beneficial effects of laser irradiation on the fabrication process of diamond/Ni60 composite coating using cold spray. The focus of this research is on the comparison between the composite coatings produced with laser cladding (LC) and with supersonic laser deposition (SLD), with respect to diamond graphitization and tribological properties, thus to demonstrate the beneficial effects of laser irradiation on the cold spray process. The influence of deposition temperature on the coating characteristics, such as deposition efficiency, diamond volume fraction, microstructure and phase is also investigated. The tribological properties of the diamond/Ni60 composite coating produced with SLD are determined using a pin-on-disc tribometer, along with the diamond/Ni60 coating produced using LC with the optimal process parameters for comparison. The experimental results show that with the assistance of laser irradiation, diamond/Ni60 composite coating can be successfully deposited using cold spray; the obtained coating is superior to that processed with LC, because SLD can suppress the graphitization of the diamond particles. The diamond/Ni60 composite coating fabricated with SLD has much better tribological properties than the LC coating.

    12. An experimental study on moisture absorption for jute-epoxy composite with coatings exposed to different pH media

      Directory of Open Access Journals (Sweden)

      Radhika Londhe

      2016-09-01

      The purpose of this work is to study the moisture absorption and mechanical properties of jute-epoxy composites. Jute fibres are treated with NaOH before manufacturing of composite laminate in order to improve adhesion with epoxy material. Further jute-epoxy composite specimens were coated with epoxy resin and acrylic paint. Composite specimens with and without coatings are subjected to absorption in solutions of different pH media, for 28 days (666 h. The effect of coatings on reduction in moisture absorption for jute-epoxy composite is presented in this current work.

    13. Enhancement of heat dissipation of LED module with cupric-oxide composite coating on aluminum-alloy heat sink

      International Nuclear Information System (INIS)

      Kim, Donghyun; Lee, Junghoon; Kim, Junho; Choi, Chang-Hwan; Chung, Wonsub

      2015-01-01

      Highlights: • We fabricate the CuO/resin composite coating layer on aluminum alloy heat sink. • CuO/resin coating considerably improved the surface emissivity. • The LED junction temperature was reduced by CuO/resin coated heat sink. • The thermal resistance of heat sink was decreased by CuO/resin composite coating at 200 μm thickness. - Abstract: A composite coating composed of cupric oxide (CuO) and silicon-based resin was applied to an aluminum-alloy heat sink for a light emitting diode (LED) module. The purpose of the composite coating is to improve the heat dissipation performance of heat sink by enhancing thermal radiation emission. The heat dissipation performance was investigated in terms of LED junction temperature and thermal resistance using a thermal transient method. The CuO and silicon-based resin composite coating showed higher emissivity, and the lower junction temperature and thermal resistance of the heat sink was achieved. In addition, a continuous operation test of the LED chip with the heat sink revealed that the surface treated with the CuO composite coating stably dissipated heat without degradation. In conclusion, the composite coating proposed here showed a significant improvement of the heat dissipation performance of the aluminum-alloy heat sink due to the enhanced thermal radiation property.

    14. Preparation and characterization of the micro-arc oxidation composite coatings on magnesium alloys

      Directory of Open Access Journals (Sweden)

      Yanfeng Ge

      2014-12-01

      Full Text Available The magnesium alloys attract the light-weight manufacture due to its high strength to weight ratio, however the poor corrosion resistance limits the application in automobile industry. The Micro-arc Composite Ceramic (MCC coatings on AZ91D magnesium alloys were prepared by Micro-arc Oxidation (MAO and electrophoresis technologies. The microstructure, corrosion resistance, abrasion resistance, stone impact resistance and adhesion of MCC coatings were studied respectively. The cross section morphologies showed that the outer organic coating was filled into the hole on surface of MAO coating, and it acted as a shelter against corrosive products. The copper-accelerated acetic acid salt spray Test, abrasion resistance test, stone impact resistance test, thermal shock resistance test and adhesion test were used to evaluate the protective characterization by the third testing organization which approved by GM. The test results showed the composite coatings meet all the requirements. The MCC coating on Mg presents excellent properties, and it is a promising surface treatment technology on magnesium alloys for production vehicles.

    15. Influence of monomer on structure, processing and application characteristics of UV curable urethane acrylate composite coatings

      International Nuclear Information System (INIS)

      Grigale-Sorocina, Z; Kalnins, M; Gross, K A

      2016-01-01

      Increased interest in the esthetical natural nail coatings have encouraged more in-depth studies particularly of UV curable coatings: their formation, processing, structure, characteristics and removing. Typical requirement for nail coatings is good adhesion, but preferably for the short time of functioning (usual 2-4 weeks). This study investigated the impact of four different monomers (tertiobutyl cyclohexyl acrylate (TBCHA), ethylene glycol dimethacrylate (EGDMA), tetrahydrofurfuryl acrylate (THFA), hydroxypropyl methacrylate (HPMA)) to viscosity of uncured mixture and degree of conversion, mechanical properties, surface gloss, micro hardness and adhesion loss for cured films. Specific coating application requires comparatively high coating flexibility and stability of deformation characteristics. This can be achieved with composition containing 30% of monomer TBCHA, what shows ultimate elongation ε B = 0,23 - 0,24, modulus of elasticity E = 670-710 MPa and comparatively constant properties in 72 hours (ΔE = 1.3%, Δε B =6.0%). A composition with 40% of TBCHA shows the fastest coating destruction achieving adhesion loss within 3 min. (paper)

    16. Annealing effects on magnetic properties of silicone-coated iron-based soft magnetic composites

      International Nuclear Information System (INIS)

      Wu Shen; Sun Aizhi; Zhai Fuqiang; Wang Jin; Zhang Qian; Xu Wenhuan; Logan, Philip; Volinsky, Alex A.

      2012-01-01

      This paper focuses on novel iron-based soft magnetic composites synthesis utilizing high thermal stability silicone resin to coat iron powder. The effect of an annealing treatment on the magnetic properties of synthesized magnets was investigated. The coated silicone insulating layer was characterized by scanning electron microscopy and energy dispersive X-ray spectroscopy. Silicone uniformly coated the powder surface, resulting in a reduction of the imaginary part of the permeability, thereby increasing the electrical resistivity and the operating frequency of the synthesized magnets. The annealing treatment increased the initial permeability, the maximum permeability, and the magnetic induction, and decreased the coercivity. Annealing at 580 °C increased the maximum permeability by 72.5%. The result of annealing at 580 °C shows that the ferromagnetic resonance frequency increased from 2 kHz for conventional epoxy resin coated samples to 80 kHz for the silicone resin insulated composites. - Highlights: ► Silicone uniformly coated the powder, increased the operating frequency of SMCs. ► The annealing treatment increased the DC properties of SMCs. ► Annealing at 580 °C increased the maximum permeability by 72.5%. ► Compared with epoxy coated, the SMCs had higher resistivity annealing at 580 °C.

    17. Robust Superhydrophobic Graphene-Based Composite Coatings with Self-Cleaning and Corrosion Barrier Properties.

      Science.gov (United States)

      Nine, Md J; Cole, Martin A; Johnson, Lucas; Tran, Diana N H; Losic, Dusan

      2015-12-30

      Superhydrophobic surfaces for self-cleaning applications often suffer from mechanical instability and do not function well after abrasion/scratching. To address this problem, we present a method to prepare graphene-based superhydrophobic composite coatings with robust mechanical strength, self-cleaning, and barrier properties. A suspension has been formulated that contains a mixture of reduced graphene oxide (rGO) and diatomaceous earth (DE) modified with polydimethylsiloxane (PDMS) that can be applied on any surface using common coating methods such as spraying, brush painting, and dip coating. Inclusion of TiO2 nanoparticles to the formulation shows further increase in water contact angle (WCA) from 159 ± 2° to 170 ± 2° due to the structural improvement with hierarchical surface roughness. Mechanical stability and durability of the coatings has been achieved by using a commercial adhesive to bond the superhydrophobic "paint" to various substrates. Excellent retention of superhydrophobicity was observed even after sandpaper abrasion and crosscut scratching. A potentiodynamic polarization study revealed excellent corrosion resistance (96.78%) properties, and an acid was used to provide further insight into coating barrier properties. The ease of application and remarkable properties of this graphene-based composite coating show considerable potential for broad application as a self-cleaning and protective layer.

    18. Development of functionally graded anti-oxidation coatings for carbon/carbon composites

      Energy Technology Data Exchange (ETDEWEB)

      Jeon, J.H. [Dept. of Materials Technology, Korea Inst. of Machinery and Materials, Changwon (Korea); Fang Hai-Tao; Lai Zhong-Hong; Yin Zhong-Da [Materials Science and Engineering School, Harbin Inst. of Tech., Harbin (China)

      2005-07-01

      The concept of functionally graded materials (FGMs) was originated in the research field of thermal barrier coatings. Continuous changes in the composition, grain size, porosity, etc., of these materials result in gradients in such properties as mechanical strength and thermal conductivity. In recent years, functionally graded structural composite materials have received increased attention as promising candidate materials to exhibit better mechanical and functional properties than homogeneous materials or simple composite materials. Therefore the research area of FGMs has been expending in the development of various structural and functional materials, such as cutting tools, photonic crystals, dielectric and piezoelectric ceramics, thermoelectric semiconductors, and biomaterials. We have developed functionally graded structural ceramic/metal composite materials for relaxation of thermal stress, functionally graded anti-oxidation coatings for carbon/carbon composites, and functionally graded dielectric ceramic composites to develop advanced dielectric ceramics with flat characteristics of dielectric constant in a wide temperature range. This paper introduces functionally graded coatings for C/C composites with superior oxidation resistance at high temperatures. (orig.)

    19. Development of high performance electroless Ni-P-HNT composite coatings

      Energy Technology Data Exchange (ETDEWEB)

      Ranganatha, S., E-mail: kamath.ranganath@gmail.com [Department of studies in chemistry, School of chemical sciences, Kuvempu university, Shankaraghatta-577451, Shimoga, Karnataka (India); Venkatesha, T.V., E-mail: drtvvenkatesha@yahoo.co.uk [Department of studies in chemistry, School of chemical sciences, Kuvempu university, Shankaraghatta-577451, Shimoga, Karnataka (India); Vathsala, K., E-mail: vathsala.mahesh@gmail.com [Nanotribology Laboratory, Mechanical engineering department, Indian Institute of Science, Bangalore 560012, Karnataka (India)

      2012-12-15

      Highlights: Black-Right-Pointing-Pointer Novel Ni-P composites were prepared by incorporating Halloysite nanotubes. Black-Right-Pointing-Pointer Mild steel specimens surface engineered by nickel using electroless technique. Black-Right-Pointing-Pointer Incorporated halloysite nanotubes made nickel matrix highly corrosion resistant. Black-Right-Pointing-Pointer HNT composite exhibits high hardness and largely reduces friction. - Abstract: Halloysite nanotubes (HNTs) of the dimension 50 nm Multiplication-Sign 1-3 {mu}m (diameter Multiplication-Sign length) are utililized to fabricate the alloy composite by employing electroless/autocatalytic deposition technique. Electroless Ni-P-HNT binary alloy composite coatings are prepared successfully on low carbon steel. These nanotubes were made to get inserted/incorporated into nickel matrix and corresponding composites are examined for their electrochemical, mechanical and tribological performances and compared with that of plain Ni-P. The coatings were characterized using scanning electron microscopy (SEM) and Energy dispersive X-ray analysis (EDX) techniques to analyze surface nature and composition correspondingly. Small amount of incorporated HNTs made Ni-P deposits appreciable enhancement and betterment in corrosion resistance, hardness and friction resistance. This drastic improvement in the properties reflects the effect of addition of HNTs into Ni-P matrix leading to the development of high performance Ni-P-HNT composite coatings.

    20. Development of high performance electroless Ni–P–HNT composite coatings

      International Nuclear Information System (INIS)

      Ranganatha, S.; Venkatesha, T.V.; Vathsala, K.

      2012-01-01

      Highlights: ► Novel Ni–P composites were prepared by incorporating Halloysite nanotubes. ► Mild steel specimens surface engineered by nickel using electroless technique. ► Incorporated halloysite nanotubes made nickel matrix highly corrosion resistant. ► HNT composite exhibits high hardness and largely reduces friction. - Abstract: Halloysite nanotubes (HNTs) of the dimension 50 nm × 1–3 μm (diameter × length) are utililized to fabricate the alloy composite by employing electroless/autocatalytic deposition technique. Electroless Ni–P–HNT binary alloy composite coatings are prepared successfully on low carbon steel. These nanotubes were made to get inserted/incorporated into nickel matrix and corresponding composites are examined for their electrochemical, mechanical and tribological performances and compared with that of plain Ni–P. The coatings were characterized using scanning electron microscopy (SEM) and Energy dispersive X-ray analysis (EDX) techniques to analyze surface nature and composition correspondingly. Small amount of incorporated HNTs made Ni–P deposits appreciable enhancement and betterment in corrosion resistance, hardness and friction resistance. This drastic improvement in the properties reflects the effect of addition of HNTs into Ni–P matrix leading to the development of high performance Ni–P–HNT composite coatings.

    1. ZnO nanorod array polydimethylsiloxane composite solid phase micro-extraction fiber coating: fabrication and extraction capability.

      Science.gov (United States)

      Wang, Dan; Wang, Qingtang; Zhang, Zhuomin; Chen, Guonan

      2012-01-21

      ZnO nanorod array coating is a novel kind of solid-phase microextraction (SPME) fiber coating which shows good extraction capability due to the nanostructure. To prepare the composite coating is a good way to improve the extraction capability. In this paper, the ZnO nanorod array polydimethylsiloxane (PDMS) composite SPME fiber coating has been prepared and its extraction capability for volatile organic compounds (VOCs) has been studied by headspace sampling the typical volatile mixed standard solution of benzene, toluene, ethylbenzene and xylene (BTEX). Improved detection limit and good linear ranges have been achieved for this composite SPME fiber coating. Also, it is found that the composite SPME fiber coating shows good extraction selectivity to the VOCs with alkane radicals.

    2. Surface enhanced 316L/SiC nano-composite coatings via laser cladding and following cold-swaging process

      Science.gov (United States)

      Li, Yuhang; Gao, Shiyou

      2017-10-01

      Cold-swaging is one of a cold deformation processes, and ceramic-reinforcement nano-composite coatings can effectively improve the performance of metal matrix surface. Therefore, the two processes are innovatively combined to further improve the surface properties of the metal matrix in this paper. The microstructure and surface properties of the laser cladding 316L + 10 wt% SiC nano-composite coatings were examined through designed experiments after cold-swaging by self-developed hydraulic machine. Furthermore, the coatings were compared with those without cold-swaging coatings at the same time. The result shows that the cold-swaging process can further enhance the tensile strength, micro-hardness and the wear resistance of the composite coating. This study can be used as a reference for further strengthening of laser cladding nano-composite coatings in future research.

    3. TiC Reinforcement Composite Coating Produced Using Graphite of the Cast Iron by Laser Cladding

      Directory of Open Access Journals (Sweden)

      Yanhui Liu

      2016-09-01

      Full Text Available In this study, a TiC-reinforced composite coating was produced to improve the wear resistance of a pearlite matrix grey iron using a pre-placed Ti powder by laser cladding. Results of scanning electron microscopy (SEM, X-ray diffractometer (XRD, and energy dispersive X-ray spectroscopy (EDS confirmed that the coating was composed of TiC particles and two kinds of α-Fe phase. The fine TiC particles were only a few microns in size and uniformly distributed on the matrix phase in the composite coating. The microstructure characteristic of the composite coating resulted in the microhardness rising to about 1000 HV0.3 (China GB/T 4342-1991 and the wear resistance significantly increased relative to the substrate. In addition, the fine and homogeneous solidification microstructure without graphite phase in the transition zone led to a good metallurgical bonding and transition between the coating and the substrate. It was of great significance for the cast iron to modify the surface and repair surface defects or surface damage.

    4. TiC Reinforcement Composite Coating Produced Using Graphite of the Cast Iron by Laser Cladding.

      Science.gov (United States)

      Liu, Yanhui; Qu, Weicheng; Su, Yu

      2016-09-30

      In this study, a TiC-reinforced composite coating was produced to improve the wear resistance of a pearlite matrix grey iron using a pre-placed Ti powder by laser cladding. Results of scanning electron microscopy (SEM), X-ray diffractometer (XRD), and energy dispersive X-ray spectroscopy (EDS) confirmed that the coating was composed of TiC particles and two kinds of α -Fe phase. The fine TiC particles were only a few microns in size and uniformly distributed on the matrix phase in the composite coating. The microstructure characteristic of the composite coating resulted in the microhardness rising to about 1000 HV0.3 (China GB/T 4342-1991) and the wear resistance significantly increased relative to the substrate. In addition, the fine and homogeneous solidification microstructure without graphite phase in the transition zone led to a good metallurgical bonding and transition between the coating and the substrate. It was of great significance for the cast iron to modify the surface and repair surface defects or surface damage.

    5. Electrophoretic deposition of PEEK-TiO 2 composite coatings on stainless steel

      KAUST Repository

      Seuß, Sigrid

      2012-03-01

      Electrophoretic deposition (EPD) has been successfully used to deposit composite coatings composed of polyetheretherketone (PEEK) and titanium dioxide (TiO 2) nanoparticles on 316L stainless steel substrates. The suspensions of TiO2 nanoparticles and PEEK microparticles for EPD were prepared in ethanol. PEEK-TiO 2 composite coatings were optimized using suspensions containing 6wt% PEEK-TiO 2 in ethanol with a 3:1 ratio of PEEK to TiO 2 in weight and by applying a potential difference of 30 V for 1 minute. A heat-treatment process of the optimized PEEK-TiO 2 composite coatings was erformed at 335°C for 30 minutes with a heating rate of 10°Cmin -1 to densify the deposits. The EPD coatings were microstructurally evaluated by scanning electron microscopy (SEM). It was demonstrated that EPD is a convenient and rapid method to fabricate PEEK/TiO 2 coatings on stainless steel which are interesting for biomedical applications. © (2012) Trans Tech Publications, Switzerland.

    6. Fabrication of superhydrophobic coating for preventing microleakage in a dental composite restoration.

      Science.gov (United States)

      Cao, Danfeng; Zhang, Yingchao; Li, Yao; Shi, Xiaoyu; Gong, Haihuan; Feng, Dan; Guo, Xiaowei; Shi, Zuosen; Zhu, Song; Cui, Zhanchen

      2017-09-01

      Superhydrophobic coatings were successfully fabricated by photo-crosslinked polyurethane (PU) and organic fluoro group-functionalized SiO 2 nanoparticles (F-SiO 2 NPs), and were introduced for preventing microleakage in a dental composite restoration. The F-SiO 2 NPs possessed low surface energy and the PU can not only improve the mechanical stability but also promote F-SiO 2 NPs to form multiscale structure, which could facilitate the properties of the as-prepared superhydrophobic coating by synergetic effect. The morphology and properties of the resulted superhydrophobic coatings with different PU/F-SiO 2 ratios were studied using 1 H NMR spectrum, fourier transform infrared spectra, scanning electron microscopy, atomic force microscopy and UV-vis spectrophotometry. The results showed that the superhydrophobic coatings with low PU/F-SiO 2 ratio (1:3) possessed excellent hierarchical papillae structure with trapped air pockets, high contact angle (160.1°), low sliding angle (superhydrophobic property, the as-prepared superhydrophobic coatings effectively prevented water permeation in resin composite restoration evaluation. This research may provide an effective method to solve the problem of microleakage and will efficiently increase the success rate of dental composite restorations. Copyright © 2017 Elsevier B.V. All rights reserved.

    7. The erosion performance of cold spray deposited metal matrix composite coatings with subsequent friction stir processing

      Energy Technology Data Exchange (ETDEWEB)

      Peat, Tom, E-mail: tompeat12@gmail.com [Department of Mechanical & Aerospace Engineering, University of Strathclyde, James Weir Building, 75 Montrose Street, Glasgow G1 1XJ (United Kingdom); Galloway, Alexander; Toumpis, Athanasios [Department of Mechanical & Aerospace Engineering, University of Strathclyde, James Weir Building, 75 Montrose Street, Glasgow G1 1XJ (United Kingdom); McNutt, Philip [TWI Ltd., Granta Park, Cambridge CB21 6AL (United Kingdom); Iqbal, Naveed [TWI Technology Centre, Wallis Way, Catcliff, Rotherham, S60 5TZ (United Kingdom)

      2017-02-28

      Highlights: • WC-CoCr, Cr{sub 3}C{sub 2}-NiCr and Al{sub 2}O{sub 3} coatings were cold spray deposited on AA5083 and friction stir processed. • The SprayStirred WC-CoCr demonstrated a hardness increase of 100% over the cold sprayed coating. • As-deposited and SprayStirred coatings were examined under slurry erosion test conditions. • Mass and volume loss was measured following 20-min exposure to the slurry. • The WC-CoCr and Al2O3 demonstrated a reduction in volume loss of approx. 40% over the cold sprayed coating. - Abstract: This study forms an initial investigation into the development of SprayStir, an innovative processing technique for generating erosion resistant surface layers on a chosen substrate material. Tungsten carbide – cobalt chromium, chromium carbide – nickel chromium and aluminium oxide coatings were successfully cold spray deposited on AA5083 grade aluminium. In order to improve the deposition efficiency of the cold spray process, coatings were co-deposited with powdered AA5083 using a twin powder feed system that resulted in thick (>300 μm) composite coatings. The deposited coatings were subsequently friction stir processed to embed the particles in the substrate in order to generate a metal matrix composite (MMC) surface layer. The primary aim of this investigation was to examine the erosion performance of the SprayStirred surfaces and demonstrate the benefits of this novel process as a surface engineering technique. Volumetric analysis of the SprayStirred surfaces highlighted a drop of approx. 40% in the level of material loss when compared with the cold spray deposited coating prior to friction stir processing. Micro-hardness testing revealed that in the case of WC-CoCr reinforced coating, the hardness of the SprayStirred material exhibits an increase of approx. 540% over the unaltered substrate and 120% over the as-deposited composite coating. Microstructural examination demonstrated that the increase in the hardness of the

    8. Wear behaviour of plasma-sprayed AlSi/B4C composite coatings

      International Nuclear Information System (INIS)

      Sarikaya, Ozkan; Anik, Selahaddin; Celik, Erdal; Okumus, S. Cem; Aslanlar, Salim

      2007-01-01

      This paper describes the wear behaviour of AlSi/B 4 C composite coatings with 0-25 wt% B 4 C particles for diesel engine motors. These coatings were successfully fabricated on AlSi substrates using an atmospheric plasma spray technique. The produced samples were characterized by means of an optical microscope, scanning electron microscope and microhardness tester. The obtained results pointed out that an increase of B 4 C particles in AlSi coatings was caused on the rising of the microhardness values and the decrease of the thermal expansion coefficient of the coatings. The friction and wear experiments were performed under dry conditions using a ball-on-dics configuration against WC/Co counter material for different loads. It was concluded that wear resistance of the coatings produced using B 4 C powders is greatly improved compared with the substrate material. The highest wear resistance of the coatings were also determined in the 20% B 4 C coating

    9. Surface modification of polyamide thin film composite membrane by coating of titanium dioxide nanoparticles

      Directory of Open Access Journals (Sweden)

      Thu Hong Anh Ngo

      2016-12-01

      Full Text Available In this paper, the coating of TiO2 nanoparticles onto the surface of a polyamide thin film composite nanofiltration membrane has been studied. Changes in the properties and separation performance of the modified membranes were systematically characterized. The experimental results indicated that the membrane surface hydrophilicity was significantly improved by the presence of the coated TiO2 nanoparticles with subsequent UV irradiation. The separation performance of the UV-irradiated TiO2-coated membranes was improved with a great enhancement of flux and a very high retention for removal of residual dye in an aqueous feed solution. The antifouling property of the UV-irradiated TiO2-coated membranes was enhanced with higher maintained flux ratios and lower irreversible fouling factors compared with an uncoated membrane.

    10. Bioactive and Antibacterial Coatings Based on Zein/Bioactive Glass Composites by Electrophoretic Deposition

      Directory of Open Access Journals (Sweden)

      Nima Meyer

      2018-01-01

      Full Text Available This study investigated the electrophoretic deposition (EPD of the natural polymer zein combined with bioactive glass (BG particles. Through the deposition of various BG compositions, namely 45S5 BG and Cu-doped BG, this work sought to demonstrate the ability of the films to potentiate the formation of hydroxyapatite (HA in contact with simulated body fluid (SBF. Following incubation in SBF, the physical and chemical surface properties of the EPD films were evaluated using different characterization techniques. The formation of HA at the surface of the coatings following immersion in SBF was confirmed using Fourier transform infrared spectroscopy (FTIR. The results demonstrated HA formation in all coatings after seven days of immersion in SBF. Coating morphology and degradation of the zein films were characterized using environmental scanning electron microscopy (ESEM. The results confirmed EPD as a very convenient room temperature technique for production of ion releasing, bioactive, and antibacterial coatings for potential application in orthopedics.

    11. Corrosion and drug release properties of EN-plating/PLGA composite coating on MAO film

      International Nuclear Information System (INIS)

      Lu Ping; Liu Yin; Guo Meiqing; Fang Haidong; Xu Xinhua

      2011-01-01

      The electroless nickel plating/poly(DL-lactide-co-glycolide) composite coating (EN-plating/PLGA composite coating) was fabricated on the surface of the micro-arc oxidation (MAO) film of the magnesium alloy AZ81 to double control the corrosion and drug release in the hanks' solution. The EN-plating was fabricated on the MAO coating to improve the corrosion resistance by overlaying most pores and micro-cracks on the surface of the MAO film. Meanwhile, a double layered organic poly(DL-lactide-co-glycolide)/paclitaxel (PLGA/PTX) drug releasing coating with a top layered PLGA drug controlled releasing coating on EN plating was prepared to control the drug release rate by adjusting the different lactide: glycolide (LA:GA) ratio of PLGA. Scanning electron microscopy (SEM) and the X-ray powder diffraction (XRD) were used to analyze the morphology and the composition of the EN-plating. The corrosion behavior of the magnesium alloy substrate and the status of the drug in the PLGA matrix were respectively evaluated by Potentiodynamic polarization and Differential scanning calorimetry (DSC). The drug release was determined by ultraviolet-visible (UV-visible) spectrophotometer. EN-plating coating which was composed of compact cauliflower nodules was uniform in size and defect free with no pores or cracks. EN-plating could seal the microcracks and microholes on the outer layer of the MAO coating effectively. The corrosion resistance was improved by preventing the corrosive ions from diffusing to the magnesium alloy substrate. The drug release rate of PTX exhibited a nearly linear sustained-release profile with no significant burst releases. - Research highlights: → An organic and in organic EN-plating/PLGA composite coating was first fabricated on the surface of the MAO film. → This composite coating the magnesium alloy AZ81could double control the corrosion and drug release in the hanks' solution. → The drug release rate could be controlled by LG:GA ratio and the PTX

    12. Corrosion and drug release properties of EN-plating/PLGA composite coating on MAO film

      Energy Technology Data Exchange (ETDEWEB)

      Lu Ping [School of Materials Science and Engineering, and Tianjin Key Laboratory of Composite and Functional Materials, Tianjin University, Tianjin 300072 (China); Liu Yin [Department of Cardiology, Tianjin Chest Hospital, Tianjin 300051 (China); Guo Meiqing; Fang Haidong [School of Materials Science and Engineering, and Tianjin Key Laboratory of Composite and Functional Materials, Tianjin University, Tianjin 300072 (China); Xu Xinhua, E-mail: xhxu_tju@eyou.com [School of Materials Science and Engineering, and Tianjin Key Laboratory of Composite and Functional Materials, Tianjin University, Tianjin 300072 (China)

      2011-10-10

      The electroless nickel plating/poly(DL-lactide-co-glycolide) composite coating (EN-plating/PLGA composite coating) was fabricated on the surface of the micro-arc oxidation (MAO) film of the magnesium alloy AZ81 to double control the corrosion and drug release in the hanks' solution. The EN-plating was fabricated on the MAO coating to improve the corrosion resistance by overlaying most pores and micro-cracks on the surface of the MAO film. Meanwhile, a double layered organic poly(DL-lactide-co-glycolide)/paclitaxel (PLGA/PTX) drug releasing coating with a top layered PLGA drug controlled releasing coating on EN plating was prepared to control the drug release rate by adjusting the different lactide: glycolide (LA:GA) ratio of PLGA. Scanning electron microscopy (SEM) and the X-ray powder diffraction (XRD) were used to analyze the morphology and the composition of the EN-plating. The corrosion behavior of the magnesium alloy substrate and the status of the drug in the PLGA matrix were respectively evaluated by Potentiodynamic polarization and Differential scanning calorimetry (DSC). The drug release was determined by ultraviolet-visible (UV-visible) spectrophotometer. EN-plating coating which was composed of compact cauliflower nodules was uniform in size and defect free with no pores or cracks. EN-plating could seal the microcracks and microholes on the outer layer of the MAO coating effectively. The corrosion resistance was improved by preventing the corrosive ions from diffusing to the magnesium alloy substrate. The drug release rate of PTX exhibited a nearly linear sustained-release profile with no significant burst releases. - Research highlights: {yields} An organic and in organic EN-plating/PLGA composite coating was first fabricated on the surface of the MAO film. {yields} This composite coating the magnesium alloy AZ81could double control the corrosion and drug release in the hanks' solution. {yields} The drug release rate could be controlled by LG

    13. Effect of plasma nitriding on electrodeposited Ni–Al composite coating

      DEFF Research Database (Denmark)

      Daemi, N.; Mahboubi, F.; Alimadadi, Hossein

      2011-01-01

      In this study plasma nitriding is applied on nickel–aluminum composite coating, deposited on steel substrate. Ni–Al composite layers were fabricated by electro-deposition process in Watt’s bath containing Al particles. Electrodeposited specimens were subjected to plasma atmosphere comprising of N2......–20% H2, at 500°C, for 5h. The surface morphology investigated, using a scanning electron microscope (SEM) and the surface roughness was measured by use of contact method. Chemical composition was analyzed by X-ray fluorescence spectroscopy and formation of AlN phase was confirmed by X-ray diffraction....... The corrosion resistance of composite coatings was measured by potentiodynamic polarization in 3.5% NaCl solution. The obtained results show that plasma nitriding process leads to an increase in microhardness and corrosion resistance, simultaneously....

    14. Structure-property relations for silicon nitride matrix composites reinforced with pyrolytic carbon pre-coated Hi-Nicalon fibers

      NARCIS (Netherlands)

      Kooi, B.J.; Hosson, J.Th.M. De; Olivier, C.; Veyret, J.B.

      1999-01-01

      Si3N4 matrix composites reinforced with pyrolytic carbon pre-coated Hi-Nicalon (SiC) fibers, were studied using tensile testing and transmission electron microscopy. Three types of samples were evaluated all with a nominal coating thickness of 200 nm. The composites were densified by hot pressing at

    15. Proximate and mineral analysis of some wild edible mushrooms

      African Journals Online (AJOL)

      israelikk

      2012-04-12

      Apr 12, 2012 ... Key words: Edible mushroom, mineral composition, proximate analysis. ... than beef, pork and chicken that contain similar nutrients. .... legumes and meat. In earlier studies, Gruen and Wong. (1982) indicated that edible mushrooms were highly nutritional and compared favourably with meat, egg and milk.

    16. Laminated composite based on polyester geotextile fibers and polyurethane resin for coating wood structures

      Directory of Open Access Journals (Sweden)

      Yuri Andrey Olivato Assagra

      2013-01-01

      Full Text Available New environmental laws have restricted the use of hardwood trees in overhead power lines structures, such as, poles and cross-arms, leading companies to seek alternative materials. Reforested wood coated with polymeric resin has been proposed as an environmental friendly solution, with improved electrical properties and protection against external agents, e.g. moisture, ultraviolet radiation and fungi. However, the single thin layer of resin, normally applied on such structures reveal to be inefficient, due to be easily damage during handling. In this paper, we present a composite coating, based on geotextile fibers and polyurethane resin that is suitable for wooden structures. Results obtained from two different tree species (from managed and reforested areas coated with the composite reveal that the additional layer not only provided a stronger adhesion between wood and ccoating layer but also a further improvement in the electrical properties and better protection against abrasion and moisture.

    17. Self-healing coatings based on halloysite clay polymer composites for protection of copper alloys.

      Science.gov (United States)

      Abdullayev, Elshad; Abbasov, Vagif; Tursunbayeva, Asel; Portnov, Vasiliy; Ibrahimov, Hikmat; Mukhtarova, Gulbaniz; Lvov, Yuri

      2013-05-22

      Halloysite clay nanotubes loaded with corrosion inhibitors benzotriazole (BTA), 2-mercaptobenzimidazole (MBI), and 2-mercaptobenzothiazole (MBT) were used as additives in self-healing composite paint coating of copper. These inhibitors form protective films on the metal surface and mitigate corrosion. Mechanisms involved in the film formation have been studied with optical and electron microscopy, UV-vis spectrometry, and adhesivity tests. Efficiency of the halloysite lumen loading ascended in the order of BTA halloysite formulations have shown the best protection. Inhibitors were kept in the tubes buried in polymeric paint layer for a long time and release was enhanced in the coating defects exposed to humid media with 20-50 h, sufficient for formation of protective layer. Anticorrosive performance of the halloysite-based composite acrylic and polyurethane coatings have been demonstrated for 110-copper alloy strips exposed to 0.5 M aqueous NaCl for 6 months.

    18. Composite materials obtained by the ion-plasma sputtering of metal compound coatings on polymer films

      Science.gov (United States)

      Khlebnikov, Nikolai; Polyakov, Evgenii; Borisov, Sergei; Barashev, Nikolai; Biramov, Emir; Maltceva, Anastasia; Vereshchagin, Artem; Khartov, Stas; Voronin, Anton

      2016-01-01

      In this article, the principle and examples composite materials obtained by deposition of metal compound coatings on polymer film substrates by the ion-plasma sputtering method are presented. A synergistic effect is to obtain the materials with structural properties of the polymer substrate and the surface properties of the metal deposited coatings. The technology of sputtering of TiN coatings of various thicknesses on polyethylene terephthalate films is discussed. The obtained composites are characterized by X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), transmission electron microscopy (TEM), energy dispersive X-ray spectroscopy (EDX), atomic force microscopy (AFM), and scanning tunneling microscopy (STM) is shown. The examples of application of this method, such as receiving nanocomposite track membranes and flexible transparent electrodes, are considered.

    19. Bio-Based Polyurethane Containing Isosorbide for Use in Composites and Coatings

      Science.gov (United States)

      2015-04-01

      ARL-TR-7259 ● APR 2015 US Army Research Laboratory Bio-Based Polyurethane Containing Isosorbide for Use in Composites and...copyright notation hereon. ARL-TR-7259 ● APR 2015 US Army Research Laboratory Bio-Based Polyurethane Containing Isosorbide for Use...4. TITLE AND SUBTITLE Bio-Based Polyurethane Containing Isosorbide for Use in Composites and Coatings 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c

    20. Bio-based coatings for reducing water sorption in natural fibre reinforced composites

      CSIR Research Space (South Africa)

      Mokhothu, Thabang H

      2017-10-01

      Full Text Available on the composites and compared with a water resistant market product. Uncoated and coated samples were conditioned at 90 °C and relative humidity of 90% for three days and the relative moisture content and mechanical properties after conditioning were analysed...

    1. Sliding mechanics of coated composite wires and the development of an engineering model for binding.

      Science.gov (United States)

      Zufall, S W; Kusy, R P

      2000-02-01

      A tribological (friction and wear) study, which was designed to simulate clinical sliding mechanics, was conducted as part of an effort to determine the suitability of poly(chloro-p-xylylene) coatings for composite orthodontic archwires. Prototype composite wires, having stiffnesses similar to those of current initial and intermediate alignment wires, were tested against stainless steel and ceramic brackets in the passive and active configurations (with and without angulation). Kinetic coefficient of friction values, which were determined to quantify sliding resistances as functions of the normal forces of ligation, had a mean that was 72% greater than uncoated wire couples at 0.43. To improve analysis of the active configuration, a mathematical model was developed that related bracket angulation, bracket width, interbracket distance, wire geometry, and wire elastic modulus to sliding resistance. From this model, kinetic coefficients of binding were determined to quantify sliding resistances as functions of the normal forces of binding. The mean binding coefficient was the same as that of uncoated wire couples at 0.42. Although penetrations through the coating were observed on many specimens, the glass-fiber reinforcement within the composite wires was undamaged for all conditions tested. This finding implies that the risk of glass fiber release during clinical use would be eliminated by the coating. In addition, the frictional and binding coefficients were still within the limits outlined by conventional orthodontic wire-bracket couples. Consequently, the coatings were regarded as an improvement to the clinical acceptability of composite orthodontic archwires.

    2. Cargo delivery to adhering myoblast cells from liposome-containing poly(dopamine) composite coatings

      DEFF Research Database (Denmark)

      Madsen, Martin Elias Lynge; Mian Teo, Boon; Laursen, Marie Bækgaard

      2013-01-01

      -engineered composite coatings to impose a corresponding cellular response, e.g., a higher amount of embedded liposomes leads to higher uptake efficiency of the fluorescent lipids and cell mean fluorescence or a higher reduction in the viability of the adhering cells. Assessment of the uptake efficiency and cell mean...

    3. Siloxane urethane acrylate radiation curable compounds for use in coating compositions

      International Nuclear Information System (INIS)

      Friedlander, C.B.; McMullen, J.C.

      1978-01-01

      Radiation curable compounds are disclosed which are derived from the reaction of siloxy-containing carbinol, a polyisocyanate and a polyfunctional compound having hydroxy and acrylic functional groups. The compounds have high cure rates, are compatible with other components of radiation curable, film forming compositions and impart good slip and other properties to cured film coatings

    4. Electrochemically Active Polyaniline (PANi) Coated Carbon Nanopipes and PANi Nanofibers Containing Composite.

      Science.gov (United States)

      Ramana, G Venkata; Kumar, P Sampath; Srikanth, Vadali V S S; Padya, Balaji; Jain, P K

      2015-02-01

      A composite constituted by carbon nanopipes (CNPs) and polyaniline nanofibers (PANi NFs) is synthesized using in-situ chemical oxidative polymerization. Owing to its electrochemical activity the composite is found to be suitable as a working electrode material in hybrid type supercapacitors. Microstructural and phase analyses of the composite showed that (i) CNP surfaces are coated with PANi and (ii) PANi coated CNPs are distributed among PANi NFs. The composite shows an excellent electrochemical activity and a high specific capacitance of ~224.39 F/g. The electro-chemical activity of the composite is explicated in correlation with crystallinity, intrinsic oxidation state, and doping degree of PANi in the composite. The electro-chemical activity of the composite is also explicated in correlation with BET surface area and ordered meso-porosity pertaining to the composite. Charge/discharge curves indicate that the specific capacitance of the composite is a result of electric double-layer capacitance offered by CNPs and Faradaic pseudo capacitance offered by PANi NFs.

    5. Degradation behavior of n-MAO/EPD bio-ceramic composite coatings on magnesium alloy in simulated body fluid

      Energy Technology Data Exchange (ETDEWEB)

      Xiong, Ying, E-mail: yxiong@zjut.edu.cn [College of Mechanical Engineering, Zhejiang University of Technology, Hangzhou 310032 (China); Lu, Chao [College of Mechanical Engineering, Zhejiang University of Technology, Hangzhou 310032 (China); Wang, Chao; Song, Renguo [School of Materials Science and Engineering, Changzhou University, Changzhou 213164 (China); Jiangsu Key Laboratory of Materials Surface Science and Technology, Changzhou University, Changzhou 213164 (China)

      2015-03-15

      Highlights: • A bio-ceramic n-MAO/EPD coating was prepared by combined MAO and EPD technique. • The precipitates of Ca/P compound are formed on the surface samples during immersion. • The n-MAO/EPD coating with HA dense structure has a favorable anti-corrosion effect. • Two degradation mechanism models for the n-MAO and n-MAO/EPD coating were proposed. - Abstract: The bio-ceramic composite coatings have been fabricated on ZK60 magnesium (Mg) alloy to improve its bio-corrosion resistance in a simulated body fluid (SBF). Firstly, micro-arc oxidation coatings (n-MAO coating) with the addition of zirconium oxide (ZrO{sub 2}) and cerium oxide (CeO{sub 2}) nano-particles were prepared by MAO technique on ZK60Mg alloy in alkaline electrolyte. Secondly, nano-hydroxyapatite (HA) was deposited on the surface of n-MAO coatings by using electrophoretic deposition (EPD) technique. The degradation behavior of the coated samples was investigated by means of immersion tests and electrochemical impedance spectroscopy (EIS) in the SBF at 36.5 ± 0.5 °C. The variation of phase composition, surface and cross-section morphology of coatings at different immersion stages were analyzed by X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. The results showed that the precipitation layer with biological activity formed on the surface of coated samples during the SBF immersion, which can inhibit Mg alloys from degrading effectively. The n-MAO/EPD composite coating with HA dense structure has a favorable anti-corrosion effect compared to the n-MAO coating. Degradation mechanism model of the corrosion process at different corrosion stages for two kinds of coatings were proposed. The long-term corrosion protection of the n-MAO/EPD composite coating was governed significantly by the synergistic effect of phase composition stability and micro structural integrity.

    6. Degradation behavior of n-MAO/EPD bio-ceramic composite coatings on magnesium alloy in simulated body fluid

      International Nuclear Information System (INIS)

      Xiong, Ying; Lu, Chao; Wang, Chao; Song, Renguo

      2015-01-01

      Highlights: • A bio-ceramic n-MAO/EPD coating was prepared by combined MAO and EPD technique. • The precipitates of Ca/P compound are formed on the surface samples during immersion. • The n-MAO/EPD coating with HA dense structure has a favorable anti-corrosion effect. • Two degradation mechanism models for the n-MAO and n-MAO/EPD coating were proposed. - Abstract: The bio-ceramic composite coatings have been fabricated on ZK60 magnesium (Mg) alloy to improve its bio-corrosion resistance in a simulated body fluid (SBF). Firstly, micro-arc oxidation coatings (n-MAO coating) with the addition of zirconium oxide (ZrO 2 ) and cerium oxide (CeO 2 ) nano-particles were prepared by MAO technique on ZK60Mg alloy in alkaline electrolyte. Secondly, nano-hydroxyapatite (HA) was deposited on the surface of n-MAO coatings by using electrophoretic deposition (EPD) technique. The degradation behavior of the coated samples was investigated by means of immersion tests and electrochemical impedance spectroscopy (EIS) in the SBF at 36.5 ± 0.5 °C. The variation of phase composition, surface and cross-section morphology of coatings at different immersion stages were analyzed by X-ray diffraction (XRD) and scanning electron microscopy (SEM), respectively. The results showed that the precipitation layer with biological activity formed on the surface of coated samples during the SBF immersion, which can inhibit Mg alloys from degrading effectively. The n-MAO/EPD composite coating with HA dense structure has a favorable anti-corrosion effect compared to the n-MAO coating. Degradation mechanism model of the corrosion process at different corrosion stages for two kinds of coatings were proposed. The long-term corrosion protection of the n-MAO/EPD composite coating was governed significantly by the synergistic effect of phase composition stability and micro structural integrity

    7. Plasma deposited composite coatings to control biological response of osteoblast-like MG-63 cells

      Science.gov (United States)

      Keremidarska, M.; Radeva, E.; Eleršič, K.; Iglič, A.; Pramatarova, L.; Krasteva, N.

      2014-12-01

      The successful osseointegration of a bone implant is greatly dependent on its ability to support cellular adhesion and functions. Deposition of thin composite coatings onto the implant surface is a promising approach to improve interactions with cells without compromising implant bulk properties. In this work, we have developed composite coatings, based on hexamethyldisiloxane (HMDS) and detonation nanodiamond (DND) particles and have studied adhesion, growth and function of osteoblast-like MG-63 cells. PPHMDS/DND composites are of interest for orthopedics because they combine superior mechanical properties and good biocompatibility of DND with high adherence of HMDS to different substrata including glass, metals and plastics. We have used two approaches of the implementation of DND particles into a polymer matrix: pre-mixture of both components followed by plasma polymerization and layer-by-layer deposition of HMDS and DND particles and found that the deposition approach affects significantly the surface properties of the resulting layers and cell behaviour. The composite, prepared by subsequent deposition of monomer and DND particles was hydrophilic, with a rougher surface and MG-63 cells demonstrated better spreading, growth and function compared to the other composite which was hydrophobic with a smooth surface similarly to unmodified polymer. Thus, by varying the deposition approach, different PPHMDS/DND composite coatings, enhancing or inhibiting osteoblast adhesion and functions, can be obtained. In addition, the effect of fibronectin pre-adsorption was studied and was found to increase greatly MG-63 cell spreading.

    8. Property Evaluation and Damage Evolution of Environmental Barrier Coatings and Environmental Barrier Coated SiC/SiC Ceramic Matrix Composite Sub-Elements

      Science.gov (United States)

      Zhu, Dongming; Halbig, Michael; Jaskowiak, Martha; Hurst, Janet; Bhatt, Ram; Fox, Dennis S.

      2014-01-01

      This paper describes recent development of environmental barrier coatings on SiC/SiC ceramic matrix composites. The creep and fatigue behavior at aggressive long-term high temperature conditions have been evaluated and highlighted. Thermal conductivity and high thermal gradient cyclic durability of environmental barrier coatings have been evaluated. The damage accumulation and complex stress-strain behavior environmental barrier coatings on SiCSiC ceramic matrix composite turbine airfoil subelements during the thermal cyclic and fatigue testing of have been also reported.

    9. Edible packaging materials.

      Science.gov (United States)

      Janjarasskul, Theeranun; Krochta, John M

      2010-01-01

      Research groups and the food and pharmaceutical industries recognize edible packaging as a useful alternative or addition to conventional packaging to reduce waste and to create novel applications for improving product stability, quality, safety, variety, and convenience for consumers. Recent studies have explored the ability of biopolymer-based food packaging materials to carry and control-release active compounds. As diverse edible packaging materials derived from various by-products or waste from food industry are being developed, the dry thermoplastic process is advancing rapidly as a feasible commercial edible packaging manufacturing process. The employment of nanocomposite concepts to edible packaging materials promises to improve barrier and mechanical properties and facilitate effective incorporation of bioactive ingredients and other designed functions. In addition to the need for a more fundamental understanding to enable design to desired specifications, edible packaging has to overcome challenges such as regulatory requirements, consumer acceptance, and scaling-up research concepts to commercial applications.

    10. Electrochemical impedance spectroscopy and corrosion behaviour of Al2O3-Ni nano composite coatings

      International Nuclear Information System (INIS)

      Ciubotariu, Alina-Crina; Benea, Lidia; Lakatos-Varsanyi, Magda; Dragan, Viorel

      2008-01-01

      In this paper, the results on the electrochemical impedance spectroscopy and corrosion properties of electrodeposited nanostructured Al 2 O 3 -Ni composite coatings are presented. The nanocomposite coatings were obtained by codeposition of alumina nanoparticles (13 nm) with nickel during plating process. The coating thickness was 50 μm on steel support and an average of nano Al 2 O 3 particles inside of coatings at 15 vol.% was present. The structure of the coatings was investigated by scanning electron microscopy (SEM). It has been found that the codeposition of Al 2 O 3 particles with nickel disturbs the nickel coating's regular surface structure. The electrochemical behavior of the coatings in the corrosive solutions was investigated by polarization potentiodynamic and electrochemical impedance spectroscopy methods. As electrochemical test solutions 0.5 M sodium chloride and 0.5 M potassium sulphate were used in a three electrode open cell. The corrosion potential is shifted to more negative values for nanostructured coatings in 0.5 M sodium chloride. The polarization resistance in 0.5 M sodium chloride decreases in 24 h, but after that increases slowly. In 0.5 M potassium sulphate solution the polarization resistance decreases after 2 h and after 30 h of immersion the polarization resistance is higher than that of the beginning value. The corrosion rate calculated by polarization potentiodynamic curves obtained after 30 min from immersion in solution is smaller for nanostructured coatings in 0.5 M potassium sulphate (4.74 μm/year) and a little bit bigger in 0.5 M sodium chloride (5.03 μm/year)

    11. Environmental Barrier Coatings (EBC) for Ceramic Matrix Composite (CMC) Materials

      Science.gov (United States)

      Lee,Kang

      2001-01-01

      The upper use temperature of current Environmental Barrier Coatings (EBC's) based on mullite and BSAS (EPM EBC's) is limited to -255 F due to silica volatility, chemical reactions, and high thermal conductivity. Therefore, new EBC s having low CTE, good chemical compatibility, and high melting point (greater than 2700 F ) are being investigated. Sinter-resistant, low thermal conductivity EBC s are strongly desired to achieve the UEET EBC goal of 270 F EBC surface temperature and 30 F AT over long exposures (greater than 1000 hr). Key areas affecting the upper temperature limit of current EBC s as well as the ongoing efforts to develop next generation EBC s in the UEET Program will be discussed.

    12. Graphite coated PVA fibers as the reinforcement for cementitious composites

      Science.gov (United States)

      Zhang, Yunhua; Zhang, Zhipeng; Liu, Zhichao

      2018-02-01

      A new preconditioning method was developed to PVA fibers as the reinforcement in cement-based materials. Virgin PVA fibers exhibits limited adhesion to graphite powders due to the presence of oil spots on the surface. Mixing PVA fibers with a moderately concentrated KMnO4-H2SO4 solution can efficiently remove the oil spots by oxidation without creating extra precipitate (MnO2) associated with the reduction reaction. This enhances the coating of graphite powders onto fiber surface and improves the mechanical properties of PVA fiber reinforced concrete (PVA-FRC). Graphite powders yields better fiber distribution in the matrix and reduces the fiber-matrix bonding, which is beneficial in uniformly distributing the stress among embedded fibers and creating steady generation and propagation of tight microcracks. This is evidenced by the significantly enhanced strain hardening behavior and improved flexural strength and toughness.

    13. Influence of Metal-Coated Graphite Powders on Microstructure and Properties of the Bronze-Matrix/Graphite Composites

      Science.gov (United States)

      Zhao, Jian-hua; Li, Pu; Tang, Qi; Zhang, Yan-qing; He, Jian-sheng; He, Ke

      2017-02-01

      In this study, the bronze-matrix/x-graphite (x = 0, 1, 3 and 5%) composites were fabricated by powder metallurgy route by using Cu-coated graphite, Ni-coated graphite and pure graphite, respectively. The microstructure, mechanical properties and corrosive behaviors of bronze/Cu-coated-graphite (BCG), bronze/Ni-coated-graphite (BNG) and bronze/pure-graphite (BPG) were characterized and investigated. Results show that the Cu-coated and Ni-coated graphite could definitely increase the bonding quality between the bronze matrix and graphite. In general, with the increase in graphite content in bronze-matrix/graphite composites, the friction coefficients, ultimate density and wear rates of BPG, BCG and BNG composites all went down. However, the Vickers microhardness of the BNG composite would increase as the graphite content increased, which was contrary to the BPG and BCG composites. When the graphite content was 3%, the friction coefficient of BNG composite was more stable than that of BCG and BPG composites, indicating that BNG composite had a better tribological performance than the others. Under all the values of applied loads (10, 20, 40 and 60N), the BCG and BNG composites exhibited a lower wear rate than BPG composite. What is more, the existence of nickel in graphite powders could effectively improve the corrosion resistance of the BNG composite.

    14. Antibacterial, antioxidant and optical properties of edible starch-chitosan composite film containing Thymus kotschyanus essential oil

      Directory of Open Access Journals (Sweden)

      Tooraj Mehdizadeh

      2012-09-01

      Full Text Available Thyme Essential oils (EO with antimicrobial and antioxidant properties are widely used in pharmaceutical, cosmetic, and perfume industry. It is also used for flavoring and preservation of several foods. Nowadays, packaging research is receiving a considerable attention due to the development of eco-friendly materials made from natural polymers such as starch and chitosan. In this study Thymus kotschyanus EO concentrations ranging from 0 to 2.0%, incorporated in starch-chitosan composite (S-CH film were used. Antimicrobial and antioxidant properties significantly increased with the incorporation of EO (p < 0.05. Incorporating EO, increased total color differences (DE, yellowness index (YI and whiteness index (WI which were significantly higher than control and its transparency was reduced. Our results pointed out that the incorporation of Thymus kotschyanus EO as a natural antibacterial agent has potential for using the developed film as an active packaging.

    15. Front-facing fluoropolymer-coated armor composite

      OpenAIRE

      Gamache, Raymond M.; Roland, Charles M.; Fragiadakis, Daniel M.

      2018-01-01

      Patent A front-facing armor system utilizing a composite laminate backed by a high hardness substrate. The composite laminate comprises a series of first and second layers. The first layer of the bi-layer laminate system is a polymer with a density of at least 1.8 g/ᵌ and having both an amorphous and crystalline phase, and having phase transformation pressure of at least 0.5 GPa at a temperature of 20° C. The second layer of each bi-layer provides acoustic impedance ...

    16. Ablation behavior of rare earth La-modified ZrC coating for SiC-coated carbon/carbon composites under an oxyacetylene torch

      International Nuclear Information System (INIS)

      Jia, Yujun; Li, Hejun; Feng, Lei; Sun, Jiajia; Li, Kezhi; Fu, Qiangang

      2016-01-01

      Highlights: • La-modified ZrC coating was prepared by supersonic atmosphere plasma spraying. • The oxyacetylene ablation behavior of La-modified ZrC/SiC coating was evaluated. • The coating shows a good ablation resistance under heat flux of 2.4 MW/m"2. • La promotes the liquid phase sintering of ZrO_2 and the formation of a compact scale. • The protection of the scale results in retaining elemental C in its inner layer. - Abstract: To improve the ablation resistance of carbon/carbon (C/C) composites at ultra-high temperature, La-modified ZrC coating was prepared on SiC-coated C/C composites by supersonic atmosphere plasma spraying. The coating shows a significant improvement on the ablation resistance compared with ZrC coating and could protect C/C composites for more than 120 s under heat flux of 2.4 MW/m"2. La acted as a role in promoting the liquid phase sintering of ZrO_2 and forming a compact scale with high thermal stability, improving the ablation resistance of C/C composites.

    17. Electrodeposition and characterization of Ni-Mo-ZrO2 composite coatings

      Science.gov (United States)

      Laszczyńska, A.; Winiarski, J.; Szczygieł, B.; Szczygieł, I.

      2016-04-01

      Ni-Mo-ZrO2 composite coatings were produced by electrodeposition technique from citrate electrolytes containing dispersed ZrO2 nanopowder. The influence of deposition parameters i.e. concentration of molybdate and ZrO2 nanoparticles in the electrolyte, bath pH and deposition current density on the composition and surface morphology of the coating has been investigated. The structure, microhardness and corrosion properties of Ni-Mo-ZrO2 composites with different molybdenum and ZrO2 content have been also examined. It was found that ZrO2 content in the deposit is increased by rising the nanoparticles concentration in the plating solution up to 20 g dm-3. An increase in molybdate concentration in the electrolyte affects negatively the amount of codeposited ZrO2 nanoparticles. The correlation between the deposition current efficiency and ZrO2 content in the composite coating has been also observed. A decrease in deposition current efficiency leads to deposition of Ni-Mo-ZrO2 composite with low nanoparticles content. This may be explained by formation of higher amounts of gas bubbles on the cathode surface, which prevent the adsorption of ZrO2 nanoparticles on the growing deposit. The XRD analysis revealed that all the studied Ni-Mo-ZrO2 coatings were composed of a single, nanocrystalline phase with FCC structure. It was found that the incorporation of ZrO2 nanoparticles into Ni-Mo alloy matrix affects positively the microhardness and also slightly improves the corrosion properties of Ni-Mo alloy coating.

    18. Shear bond strength between an indirect composite layering material and feldspathic porcelain-coated zirconia ceramics.

      Science.gov (United States)

      Fushiki, Ryosuke; Komine, Futoshi; Blatz, Markus B; Koizuka, Mai; Taguchi, Kohei; Matsumura, Hideo

      2012-10-01

      This study aims to evaluate the effect of both feldspathic porcelain coating of zirconia frameworks and priming agents on shear bond strength between an indirect composite material and zirconia frameworks. A total of 462 airborne-particle-abraded zirconia disks were divided into three groups: untreated disks (ZR-AB), airborne-particle-abraded zirconia disks coated with feldspathic porcelain, (ZR-PO-AB), and hydrofluoric acid-etched zirconia disks coated with feldspathic porcelain (ZR-PO-HF). Indirect composite (Estenia C&B) was bonded to zirconia specimens with no (CON) or one of four priming agents--Clearfil Photo Bond (CPB), Clearfil Photo Bond with Clearfil Porcelain Bond Activator (CPB + activator), Estenia Opaque primer, or Porcelain Liner M Liquid B (PLB)--with or without an opaque material (Estenia C&B Opaque). All specimens were tested for shear bond strength before and after 20,000 thermocycles. The Steel-Dwass test and Mann-Whitney U test were used to compare shear bond strength. In ZR-AB specimens, the initial bond strength of the CPB and CPB + Activator groups was significantly higher as compared with the other three groups (P material, bond strength was significantly lower in ZR-AB specimens than in ZR-PO-AB and ZR-PO-HF specimens (P composite to zirconia independent of surface treatment. The use of a silane coupling agent and opaque material yields durable bond strength between the indirect composite and feldspathic-porcelain-coated zirconia. The results of the present study suggest that feldspathic porcelain coating of zirconia frameworks is an effective method to obtain clinically acceptable bond strengths of a layering indirect composite material to a zirconia framework.

    19. Investigation on the evolution of microstructure and texture of electroplated Ni–Ti composite coating by Rietveld method

      Energy Technology Data Exchange (ETDEWEB)

      Zhao, Yuantao, E-mail: zhaoyuantao@sjtu.edu.cn; Cai, Fei, E-mail: caifei32@126.com; Wang, Chengxi, E-mail: sjtucxw@sjtu.edu.cn; Chai, Ze, E-mail: zechaisjtu@163.com; Zhu, Kaiyuan, E-mail: xrd125@163.com; Xu, Zhou, E-mail: xuzhou@sjtu.edu.cn; Jiang, Chuanhai, E-mail: chjiang-sjtu@hotmail.com

      2015-10-30

      Highlights: • Ni–Ti composite coatings were prepared by electroplating. • Morphology and Ti content of Ni–Ti coatings were studied upon SEM and EDXS. • Microstructures of Ni–Ti coatings were studied upon the Rietveld method. • The texture of Ni–Ti coatings was studied upon the pole figure. - Abstract: Rietveld refinement was utilized to investigate the evolution of microstructure and texture of the Ni–Ti composite coatings electroplated at different applied current densities. Scanning Electron Microscope and Energy Dispersive Spectroscopy were utilized to investigate the morphology and chemical composition of the coatings. Relative texture coefficients (RTC) and measured pole figures were utilized to investigate the texture evolution of the coatings. The results showed that the surface morphology of the coatings changed from a colonial structure to a polyhedral one. And the incorporated Ti content decreased with increasing applied current density. As the applied current density increased, the crystallite sizes increased and their distribution got less uniform, and the microstrain and dislocation density decreased. The results of simulated pole figures obtained from Rietveld refinement illustrated that the texture of the coatings changed from no obvious texture to a strong [2 0 0] fiber texture with increasing applied current density. The texture evolution obtained from simulated pole figures was confirmed by the result of RTC and the measured pole figures. The evolutions of the microstructure and texture were derived from the change of the applied current density and incorporated Ti content in the Ni–Ti composite coatings.

    20. Electrophoretic deposition of ZnO/alginate and ZnO-bioactive glass/alginate composite coatings for antimicrobial applications

      Energy Technology Data Exchange (ETDEWEB)

      Cordero-Arias, L.; Cabanas-Polo, S.; Goudouri, O.M. [Institute of Biomaterials, Department of Materials Science and Engineering, University of Erlangen-Nuremberg, Cauerstrasse 6, D-91058 Erlangen (Germany); Misra, S.K. [Materials Science and Engineering, Indian Institute of Technology Gandhinagar, Ahmedabad 382424 (India); Gilabert, J. [Institute of Ceramics Materials (ITC), University Jaume I, Avenida Vicent SosBaynat, 12006 Castellon (Spain); Valsami-Jones, E. [School of Geography, Earth and Environmental Sciences, University of Birmingham, Edgbaston, Birmingham B15 2TT (United Kingdom); Sanchez, E. [Institute of Ceramics Materials (ITC), University Jaume I, Avenida Vicent SosBaynat, 12006 Castellon (Spain); Virtanen, S. [Institute for Surface Science and Corrosion (LKO, WW4), Department of Materials Science and Engineering, University of Erlangen-Nuremberg, Martensstrasse 7, D-91058 Erlangen (Germany); Boccaccini, A.R., E-mail: aldo.boccaccini@ww.uni-erlangen.de [Institute of Biomaterials, Department of Materials Science and Engineering, University of Erlangen-Nuremberg, Cauerstrasse 6, D-91058 Erlangen (Germany)

      2015-10-01

      Two organic/inorganic composite coatings based on alginate, as organic matrix, and zinc oxide nanoparticles (n-ZnO) with and without bioactive glass (BG), as inorganic components, intended for biomedical applications, were developed by electrophoretic deposition (EPD). Different n-ZnO (1–10 g/L) and BG (1–1.5 g/L) contents were studied for a fixed alginate concentration (2 g/L). The presence of n-ZnO was confirmed to impart antibacterial properties to the coatings against gram-negative bacteria Escherichia coli, while the BG induced the formation of hydroxyapatite on coating surfaces thereby imparting bioactivity, making the coating suitable for bone replacement applications. Coating composition was analyzed by thermogravimetric analysis (TG), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD) and energy dispersive X-ray spectroscopy (EDS) analyses. Scanning electron microscopy (SEM) was employed to study both the surface and the cross section morphology of the coatings. Polarization curves of the coated substrates made in cell culture media at 37 °C confirmed the corrosion protection function of the novel organic/inorganic composite coatings. - Highlights: • Organic–inorganic nanocomposite coatings fabricated by electrophoretic deposition • nZnO and bioactive glass containing alginate coatings exhibit antibacterial effect. • Bioactive character and anticorrosion function of coatings demonstrated.

    1. Comparison of W–TiC composite coatings fabricated by atmospheric plasma spraying and supersonic atmospheric plasma spraying

      International Nuclear Information System (INIS)

      Hou, Qing Yu; Luo, Lai Ma; Huang, Zhen Yi; Wang, Ping; Ding, Ting Ting; Wu, Yu Cheng

      2016-01-01

      Highlights: • W–TiC composite coatings were fabricated by APS and SAPS technologies. • TiC had filling effect on pores and coating/fixing effect on un-melted particles. • Porosity and oxygen content in SAPS coating were lower than that in APS coating. • Thermal conductivity of SAPS coating was higher than that of APS coating. • SAPS coating has better ability to resist to elastic fracture than APS coating does. - Abstract: Tungsten coatings with 1.5 wt.% TiC (W/TiC) were fabricated by atmospheric plasma spraying (APS) and supersonic atmospheric plasma spraying (SAPS) techniques, respectively. The results showed that the typical lamellar structure of plasma spraying and columnar crystalline grains formed in the coatings. Pores located mainly at lamellar gaps in association with oxidation were also observed. TiC phase, distributed at lamellar gaps filled the gaps; and that distributed around un-melted tungsten particles and splashed debris coated the particles or debris that were linked with the TiC at lamellar gaps. The coating and linking of the retained TiC phase prevented the tungsten particles to come off from the coatings. The porosity and the oxygen content of the SAPS-W/TiC were lower than those of the APS-W/TiC coating. The mechanical response of the coatings was strongly dependent on the H/E* ratio (H and E* are the hardness and effective Young’s modulus, respectively). The SAPS-W/TiC coating with a higher H/E* ratio had a better ability to resist to elastic fracture and better fracture toughness as compared with the APS-W/TiC coating with a smaller H/E* ratio. The thermal conductivity of the SAPS-W/TiC coating was greater than that of the APS-W/TiC coating.

    2. Microstructure and property of WC particles ceramic-metal composite coatings by laser surface cladding

      International Nuclear Information System (INIS)

      Zeng Xiaoyan; Zhu Beidi; Tao Zengyi; Yang Shuguo; Cui Kun

      1993-01-01

      Ceramic-metal is widely used as a kind of good hardfacing material. The coarse WC particles ceramic-metal composite coatings with WC density of 67% it weight and the thickness of 1.6-2.0 mm have been cladded on 20Ni 4 Mo steel surface by a 2kw CO 2 laser. The sintered WC particles with the size of 600-1,000 μm are chosen as the main strengthening phase, Ni-base self-flux alloy as the binder in the composite coatings. The microstructure and micro-hardness of both WC particles and binder are analyzed. The rigid ball indention with acoustic emission technique is used to evaluate the brittleness of the coating. Finally, the abrasive wear resistance of the coatings are tested, Besides, the coatings with the same ratio and size of WC particles within low carbon steel tube were cladded on 20Ni 4 Mo steel by atomic hydrogen welding technique and analyzed by the same ways their result are compared

    3. a Study on Microstructure Characteristics of IN SITU Formed TiC Reinforced Composite Coatings

      Science.gov (United States)

      Liu, Peng; Guo, Wei; Luo, Hui

      2012-04-01

      In situ synthesized TiC reinforced composite coating was fabricated by laser cladding of Al-Ni-Cr-C powders on titanium alloys, which can greatly improve the surface performance of the substrate. In this study, the Al-Ni-Cr-C laser-cladded composite coatings have been researched by means of X-ray diffraction, scanning electron microscope (SEM) and electron probe micro-analyzer (EPMA). There was a metallurgical combination between the Al-Ni-Cr-C laser-cladded coating and the Ti-6Al-4V substrate, and the micro-hardness of the Al-Ni-Cr-C laser-cladded coating was in the range of 1200-1450 HV0.2, which was 3-4 times higher than that of Ti-6Al-4V substrate. Furthermore, the reinforcement of theAl-Ni-Cr-C laser-cladded coating were mainly contributed to the action of the TiC, Ti3Al, Cr7C3, Al8Cr5 phases and the solution strengthening.

    4. In vitro testing of curcumin based composites coatings as antitumoral systems against osteosarcoma cells

      Science.gov (United States)

      Tirca, I.; Mitran, V.; Marascu, V.; Brajnicov, S.; Ion, V.; Stokker-Cheregi, F.; Popovici, I. A.; Cimpean, A.; Dinca, V.; Dinescu, M.

      2017-12-01

      In this work, we propose a new design for biodegradable composite coatings obtained by laser methods, which are aimed at evaluating the effects of active antitumoral elements on osteosarcoma cells. Our approach relies on embedding curcumin, which is a natural polyphenol having antitumoral properties, within biodegradable copolymer coatings (i.e. polyvinyl alcohol-polyethylene glycol - PVA-PEG) by using matrix assisted pulsed laser evaporation (MAPLE). The structural and morphological characteristics of the coatings were tailored by using different solvents (water, ethanol, benzene, dimethylsufoxide) as deposition matrix. The morphological characteristics of the resulting films were investigated by atomic force microscopy (AFM), whereas their chemical composition was characterized by Fourier transform infrared spectroscopy (FTIR). These characteristics were correlated with the degradation behavior by using ellipsometry (SE) and AFM measurements data. The in vitro study of the MG-63 osteosarcoma cell behavior indicates that the developed hybrid coatings significantly decreased osteosarcoma cell viability and proliferation potential. The physico-chemical characteristics of the thin films, along with the preliminary in vitro analyses, suggest that our developed polymeric hybrid coatings represent an efficient way to tackle the design of antitumoral surfaces, with applications in biomedicine.

    5. A Review to the Laser Cladding of Self-Lubricating Composite Coatings

      Science.gov (United States)

      Quazi, M. M.; Fazal, M. A.; Haseeb, A. S. M. A.; Yusof, Farazila; Masjuki, H. H.; Arslan, A.

      2016-06-01

      Liquid lubricants are extremely viable in reducing wear damage and friction of mating components. However, due to the relentless pressure and the recent trend towards higher operating environments in advanced automotive and aerospace turbo-machineries, these lubricants cease to perform and hence, an alternate system is required for maintaining the self-lubricating environment. From the viewpoint of tribologist, wear is related to near-surface regions and hence, surface coatings are considered suitable for improving the functioning of tribo-pairs. Wear resistant coatings can be fabricated with the addition of various solid lubricants so as to reduce friction drag. In order to protect bulk substrates, self-lubricating wear resistant composite coatings have been fabricated by employing various surface coating techniques such as electrochemical process, physical and chemical vapor depositions, thermal and plasma spraying, laser cladding etc. Studies related to laser-based surface engineering approaches have remained vibrant and are recognized in altering the near surface regions. In this work, the latest developments in laser based self-lubricating composite coatings are highlighted. Furthermore, the effect of additives, laser processing parameters and their corresponding influence on mechanical and tribological performance is briefly reviewed.

    6. Synthesis and characterization of Cerium-doped hydroxyapatite/polylactic acid composite coatings on metal substrates

      Energy Technology Data Exchange (ETDEWEB)

      Yuan, Qiuhua, E-mail: yuanqiuh@szu.edu.cn; Qin, Caoping; Wu, Jianbo; Xu, Anping; Zhang, Ziqiang; Liao, Junquan; Lin, Songxin; Ren, Xiangzhong; Zhang, Peixin

      2016-10-01

      Ce-doped hydroxyapatite/polylactic acid (HA/PLA) composites serving as implant coatings have rarely been studied by other researchers in recent years. This paper was focused to study the existence of Ce ions in structure, chemical composition and surface morphology of HA and its composite coatings. Ce-doped HA powders were synthesized by chemical precipitation method with different Ce molar fractions (0(pure HA), 0.5 mol%, 1 mol% and 2 mol%). And Ce-doped HA/PLA composite coatings were fabricated for the first time on stainless steel substrates by spin coating technique. The obtained samples were characterized by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FT-IR), scanning electron microscopy (SEM) coupled with energy dispersive X-ray detector (EDX), thermo gravimetric-differential thermal analysis (TG-DTA) and X-ray photoelectron spectroscopy (XPS). The results showed that Ce ions were doped into the crystal lattice of apatite successfully. The (Ce + Ca)/P atomic ratios in the doped HA/PLA samples ranged from 1.614 to 1.673, which were very close to the theoretical value of 1.67 for the stoichiometric HA. The addition of PLA could keep metal substrates from catalyzing the decomposition of HA. TG-DTA analysis indicated that Ce-doped HA powder had high thermal stability, and the SEM micrographs revealed that the surface topography of Ce-doped HA/PLA composite coatings was uniform and dense when the Ce molar fraction was 2 mol%. XPS results indicated that the Ce ions doped in HA showed mixed valences of Ce{sup 3+} and Ce{sup 4+}. - Highlights: • Ce-doped HA composite coatings were synthesized by spin-coating technique for the first time. • Ce ions were demonstrated to dope into HA crystal lattice successfully. • The addition of PLA could keep metal substrates from catalyzing the decomposition of HA. • XPS results showed that Ce ions doped in HA have mixed valences of Ce{sup 3+} and Ce{sup 4+}.

    7. Anti-icing properties of superhydrophobic ZnO/PDMS composite coating

      Science.gov (United States)

      Yang, Chao; Wang, Fajun; Li, Wen; Ou, Junfei; Li, Changquan; Amirfazli, Alidad

      2016-01-01

      We present the excellent anti-icing performance for a superhydrophobic coating surface based on ZnO/polydimethylsiloxane (ZnO/PDMS) composite. The superhydrophobic ZnO/PDMS coating surface was prepared by a facile solution mixing, drop coating, room-temperature curing and surface abrading procedure. The superhydrophobic ZnO/PDMS composite coating possesses a water contact angle of 159.5° and a water sliding angle of 8.3° at room temperature (5 °C). The anti-icing properties of the superhydrophobic coating were investigated by continuously dropping cold-water droplets (about 0 °C) onto the pre-cooled surface using a home-made apparatus. The sample was placed at different tilting angle (0° and 10°) and pre-cooled to various temperatures (-5, -10 and -15 °C) prior to measure. The pure Al surface was also studied for comparison. It was found that icing accretion on the surface could be reduced apparently because the water droplets merged together and slid away from the superhydrophobic surface at all of the measuring temperatures when the surface is horizontally placed. In addition, water droplet slid away completely from the superhydrophobic surface at -5 and -10 °C when the surface is tilted at 10°, which demonstrates its excellent anti-icing properties at these temperatures. When the temperature decreased to -15 °C, though ice accretion on the tilted superhydrophobic coating surface could not be avoided absolutely, the amount of ice formed on the surface is very small, which indicated that the coating surface with superhydrophobicity could significantly reduce ice accumulation on the surface at very low temperature (-15 °C). Importantly, the sample is also stable against repeated icing/deicing cycles. More meaningfully, once the superhydrophobic surface is damaged, it can be repaired easily and rapidly.

    8. Synthesis and characterization of CrCN–DLC composite coatings by cathodic arc ion-plating

      Energy Technology Data Exchange (ETDEWEB)

      Wang, R.Y. [School of Power and Mechanical Engineering, Wuhan University, Wuhan 430072 (China); Wang, L.L. [Key Laboratory of Artificial Nanomaterials and Nanostructure of Ministry of Education, School of Physics and Technology, Wuhan University, Wuhan 430072 (China); Liu, H.D. [School of Power and Mechanical Engineering, Wuhan University, Wuhan 430072 (China); Yan, S.J. [Key Laboratory of Artificial Nanomaterials and Nanostructure of Ministry of Education, School of Physics and Technology, Wuhan University, Wuhan 430072 (China); Chen, Y.M. [School of Power and Mechanical Engineering, Wuhan University, Wuhan 430072 (China); Fu, D.J. [Key Laboratory of Artificial Nanomaterials and Nanostructure of Ministry of Education, School of Physics and Technology, Wuhan University, Wuhan 430072 (China); Yang, B., E-mail: toyangbing@163.com [School of Power and Mechanical Engineering, Wuhan University, Wuhan 430072 (China)

      2013-07-15

      CrCN–DLC composite coatings were deposited onto silicon (1 0 0) and cemented carbides substrates using pure Cr targets under C{sub 2}H{sub 2} ambient by cathodic arc ion plating system. The influence of C{sub 2}H{sub 2} flow rate on the structure and mechanical properties of the coatings was investigated systemically. The coatings structure and bonding state were characterized by XRD, Raman and X-ray photoelectron spectroscopy. The chemical composition was measured by EDS. The mechanical performance and tribological behaviour of the coatings were studied by a hardness tester and ball-on-disc wear tester. The results showed that with increasing C{sub 2}H{sub 2} flow rate from 50 to 100 sccm, the corresponding hardness of coatings increased firstly and then decreased with further addition of C{sub 2}H{sub 2} flow rate. The coatings deposited at lower C{sub 2}H{sub 2} flow rate (less than 200 sccm) exhibited a relatively higher hardness value (more than HV{sub 0.025}2000) and then the hardness decrease with increasing C{sub 2}H{sub 2} flow rate. The friction coefficient also exhibited similar variation trend, when the C{sub 2}H{sub 2} flow rate was higher than 100 sccm, the friction coefficient decreased and then maintained in a relatively lower value from 0.18 to 0.24, which may be attribute to the increasing carbon content and the coating exhibited more diamond-like structure.

    9. Processing, properties and applications of composites using powder-coated epoxy towpreg technology

      Science.gov (United States)

      Bayha, T. D.; Osborne, P. P.; Thrasher, T. P.; Hartness, J. T.; Johnston, N. J.; Marchello, J. M.; Hugh, M. K.

      1993-01-01

      Composite manufacturing using the current prepregging technology of impregnating liquid resin into three-dimensionally reinforced textile preforms can be a costly and difficult operation. Alternatively, using polymer in the solid form, grinding it into a powder, and then depositing it onto a carbon fiber tow prior to making a textile preform is a viable method for the production of complex textile shapes. The powder-coated towpreg yarn is stable, needs no refrigeration, contains no solvents and is easy to process into various woven and braided preforms for later consolidation into composite structures. NASA's Advanced Composites Technology (ACT) program has provided an avenue for developing the technology by which advanced resins and their powder-coated preforms may be used in aircraft structures. Two-dimensional braiding and weaving studies using powder-coated towpreg have been conducted to determine the effect of resin content, towpreg size and twist on textile composite properties. Studies have been made to customize the towpreg to reduce friction and bulk factor. Processing parameters have been determined for three epoxy resin systems on eight-harness satin fabric, and on more advanced 3-D preform architectures for the downselected resin system. Processing effects and the resultant mechanical properties of these textile composites will be presented and compared.

    10. Crack Driving Forces in a Multilayered Coating System for Ceramic Matrix Composite Substrates