Fracture Toughness and Reliability in High-Temperature Structural Ceramics and Composites: Prospects and Challenges for the 21st Century

Science.gov (United States)

Dutta, Sunil

1999-01-01

The importance of high fracture toughness and reliability in Si3N4, and SiC-based structural ceramics and ceramic matrix composites is reviewed. The potential of these ceramics and ceramic matrix composites for high temperature applications in defense and aerospace applications such as gas turbine engines, radomes, and other energy conversion hardware have been well recognized. Numerous investigations were pursued to improve fracture toughness and reliability by incorporating various reinforcements such as particulate-, whisker-, and continuous fiber into Si3N4 and SiC matrices. All toughening mechanisms, e.g. crack deflection, crack branching, crack bridging, etc., essentially redistribute stresses at the crack tip and increase the energy needed to propagate a crack through the composite material, thereby resulting in improved fracture toughness and reliability. Because of flaw insensitivity, continuous fiber reinforced ceramic composite (CFCC) was found to have the highest potential for higher operating temperature and longer service conditions. However, the ceramic fibers should display sufficient high temperature strength and creep resistance at service temperatures above 1000 'C. The greatest challenge to date is the development of high quality ceramic fibers with associate coatings able to maintain their high strength in oxidizing environment at high temperature. In the area of processing, critical issues are, preparation of optimum matrix precursors, precursor infiltration into fiber array, and matrix densification at a temperature, where grain crystallization and fiber degradation do not occur. A broad scope of effort is required for improved processing and properties with a better understanding of all candidate composite systems.

Writing as a Design Discipline: Exploring the Relationship between Composition and Programming.

Science.gov (United States)

Walton, Richard E.; Balestri, Diane

1987-01-01

Examines similarities between composition and programming processes, and reviews two studies that linked instruction in computer programming and freshman composition to help students understand writing as a design discipline. Projects at the University of Montana and Bryn Mawr College which improved students' writing abilities are described. (LRW)

Industry to Education Technical Transfer Program & Composite Materials. Composite Materials Course. Fabrication I Course. Fabrication II Course. Composite Materials Testing Course. Final Report.

Science.gov (United States)

Massuda, Rachel

These four reports provide details of projects to design and implement courses to be offered as requirements for the associate degree program in composites and reinforced plastics technology. The reports describe project activities that led to development of curricula for four courses: composite materials, composite materials fabrication I,…

Improving the composition of voluntary programs in the category of Women in fitness

Directory of Open Access Journals (Sweden)

Iryna Bilenka

2018-04-01

Full Text Available Purpose: to reveal the basic directions of perfection of construction of compositions of voluntary programs in the category of Women in fitness. Material & Methods: judges-experts analyzed the structure and content of voluntary competitive programs of performances of six female athletes'-finalists of the championship of Ukraine on bodybuilding and fitness in 2016. Results: voluntary programs include elements of structural groups of varying complexity: "acrobatic", "choreographic", "strength" and "flexibility"; female athletes with better indicators in the quantitative analysis of competitive compositions received higher grades for performance; the results of athletes for an arbitrary program are directly proportional to the number of complex elements in the composition. Conclusions: in an voluntary program in women's fitness for a competitive result affects the saturation of the program, the variety and complexity of the elements.

A carbon-carbon composite materials development program for fusion energy applications

International Nuclear Information System (INIS)

Burchell, T.D.; Eatherly, W.P.; Engle, G.B.; Hollenberg, G.W.

1992-10-01

Carbon-carbon composites increasingly are being used for plasma-facing component (PFC) applications in magnetic-confinement plasma-fusion devices. They offer substantial advantages such as enhanced physical and mechanical properties and superior thermal shock resistance compared to the previously favored bulk graphite. Next-generation plasma-fusion reactors, such as the International Thermonuclear Experimental Reactor (ITER) and the Burning Plasma Experiment (BPX), will require advanced carbon-carbon composites possessing extremely high thermal conductivity to manage the anticipated extreme thermal heat loads. This report outlines a program that will facilitate the development of advanced carbon-carbon composites specifically tailored to meet the requirements of ITER and BPX. A strategy for developing the necessary associated design data base is described. Materials property needs, i.e., high thermal conductivity, radiation stability, tritium retention, etc., are assessed and prioritized through a systems analysis of the functional, operational, and component requirements for plasma-facing applications. The current Department of Energy (DOE) Office of Fusion Energy Program on carbon-carbon composites is summarized. Realistic property goals are set based upon our current understanding. The architectures of candidate PFC carbon-carbon composite materials are outlined, and architectural features considered desirable for maximum irradiation stability are described. The European and Japanese carbon-carbon composite development and irradiation programs are described. The Working Group conclusions and recommendations are listed. It is recommended that developmental carbon-carbon composite materials from the commercial sector be procured via request for proposal/request for quotation (RFP/RFQ) as soon as possible

Effects of high-intensity strength interval training program on body composition

OpenAIRE

Juránková, Michaela; Bílý, Jiří; Hrazdíra, Eduard

2015-01-01

The aim of this work was to examine effects of 10-week high-intensity strength interval training (HIIT) program on body composition. Seven women (31.0 ± 6.0 years old, 65.7 ± 9.8 kg body weight, 23.6 ± 2.8 kg*m−2 BMI, 18.6 ± 5.8 kg body fat, 26.0 ± 3.4 kg muscle mass) completed intervention program. We performed an analyze of body composition before and after training program. We focused especially on body fat and muscle mass. Each session consisted of short term bouts (until 30 s duration) w...

Mechanically programmed shape change in laminated elastomeric composites.

Science.gov (United States)

Robertson, Jaimee M; Torbati, Amir H; Rodriguez, Erika D; Mao, Yiqi; Baker, Richard M; Qi, H Jerry; Mather, Patrick T

2015-07-28

Soft, anisotropic materials, such as myocardium in the heart and the extracellular matrix surrounding cells, are commonly found in nature. This anisotropy leads to specialized responses and is imperative to material functionality, yet few soft materials exhibiting similar anisotropy have been developed. Our group introduced an anisotropic shape memory elastomeric composite (A-SMEC) composed of non-woven, aligned polymer fibers embedded in an elastomeric matrix. The composite exhibited shape memory (SM) behavior with significant anisotropy in room-temperature shape fixing. Here, we exploit this anisotropy by bonding together laminates with oblique anisotropy such that tensile deformation at room temperature - mechanical programming - results in coiling. This response is a breakthrough in mechanical programming, since non-affine shape change is achieved by simply stretching the layered A-SMECs at room temperature. We will show that pitch and curvature of curled geometries depend on fiber orientations and the degree of strain programmed into the material. To validate experimental results, a model was developed that captures the viscoplastic response of A-SMECs. Theoretical results correlated well with experimental data, supporting our conclusions and ensuring attainability of predictable curling geometries. We envision these smart, soft, shape changing materials will have aerospace and medical applications.

Effects of programmed physical activity on body composition in post-pubertal schoolchildren.

Science.gov (United States)

Farias, Edson Dos Santos; Gonçalves, Ezequiel Moreira; Morcillo, André Moreno; Guerra-Júnior, Gil; Amancio, Olga Maria Silverio

2015-01-01

To assess body composition modifications in post-pubertal schoolchildren after practice of a physical activity program during one school year. The sample consisted of 386 students aged between 15 and 17 years and divided into two groups: the study group (SG) comprised 195 students and the control group (CG), 191. The SG was submitted to a physical activity program and the CG attended conventional physical education classes. Body composition was assessed using body mass index (BMI), percentage of body fat (%BF), fat mass (FM), and lean mass (LM). A positive effect of the physical activity program on body composition in the SG (pgenders. A reduction in %BF (mean of differences = -5.58%) and waist circumference (-2.33 cm), as well as an increase in LM (+2.05 kg) were observed in the SG for both genders, whereas the opposite was observed in the CG. The practice of programmed physical activity promotes significant reduction of body fat in post-pubertal schoolchildren. Copyright © 2013 Sociedade Brasileira de Pediatria. Published by Elsevier Editora Ltda. All rights reserved.

PNGS-A unit 4 composite graphite valve packing program

International Nuclear Information System (INIS)

Meaney, F.

1992-01-01

During the outage of Pickering 4 for retubing and rehabilitation, a composite graphite packing program was completed on 100 conventional valves and 50 nuclear valves. This paper describes component refurbishment, related maintenance, and manpower requirements. 2 figs

Dynamic Impact Testing and Model Development in Support of NASA's Advanced Composites Program

Science.gov (United States)

Melis, Matthew E.; Pereira, J. Michael; Goldberg, Robert; Rassaian, Mostafa

2018-01-01

The purpose of this paper is to provide an executive overview of the HEDI effort for NASA's Advanced Composites Program and establish the foundation for the remaining papers to follow in the 2018 SciTech special session NASA ACC High Energy Dynamic Impact. The paper summarizes the work done for the Advanced Composites Program to advance our understanding of the behavior of composite materials during high energy impact events and to advance the ability of analytical tools to provide predictive simulations. The experimental program carried out at GRC is summarized and a status on the current development state for MAT213 will be provided. Future work will be discussed as the HEDI effort transitions from fundamental analysis and testing to investigating sub-component structural concept response to impact events.

Effects of programmed physical activity on body composition in post-pubertal schoolchildren

Directory of Open Access Journals (Sweden)

Edson dos Santos Farias

2015-04-01

Full Text Available OBJECTIVE: To assess body composition modifications in post-pubertal schoolchildren after practice of a physical activity program during one school year. METHODS: The sample consisted of 386 students aged between 15 and 17 years and divided into two groups: the study group (SG comprised 195 students and the control group (CG, 191. The SG was submitted to a physical activity program and the CG attended conventional physical education classes. Body composition was assessed using body mass index (BMI, percentage of body fat (%BF, fat mass (FM, and lean mass (LM. RESULTS: A positive effect of the physical activity program on body composition in the SG (p < 0.001 was observed, as well as on the interaction time x group in all the variables analyzed in both genders. A reduction in %BF (mean of differences = -5.58% and waist circumference (-2.33 cm, as well as an increase in LM (+2.05 kg were observed in the SG for both genders, whereas the opposite was observed in the CG. CONCLUSION: The practice of programmed physical activity promotes significant reduction of body fat in post-pubertal schoolchildren.

Industry to Education Technology Transfer Program. Composite Materials--Personnel Development. Final Report.

Science.gov (United States)

Tomezsko, Edward S. J.

A composite materials education program was established to train Boeing Helicopter Company employees in the special processing of new filament-reinforced polymer composite materials. During the personnel development phase of the joint Boeing-Penn State University project, an engineering instructor from Penn State completed a 5-month, full-time…

Composite materials research and education program: The NASA-Virginia Tech composites program

Science.gov (United States)

Herakovich, C. T.

1980-01-01

Major areas of study include: (1) edge effects in finite width laminated composites subjected to mechanical, thermal and hygroscopic loading with temperature dependent material properties and the influence of edge effects on the initiation of failure; (2) shear and compression testing of composite materials at room and elevated temperatures; (3) optical techniques for precise measurement of coefficients of thermal expansion of composites; (4) models for the nonlinear behavior of composites including material nonlinearity and damage accumulation and verification of the models under biaxial loading; (5) compressive failure of graphite/epoxy plates with circular holes and the buckling of composite cylinders under combined compression and torsion; (6) nonlinear mechanical properties of borsic/aluminum, graphite/polyimide and boron/aluminum; (7) the strength characteristics of spliced sandwich panels; and (8) curved graphite/epoxy panels subjected to internal pressure.

Computer program determines chemical composition of physical system at equilibrium

Science.gov (United States)

Kwong, S. S.

1966-01-01

FORTRAN 4 digital computer program calculates equilibrium composition of complex, multiphase chemical systems. This is a free energy minimization method with solution of the problem reduced to mathematical operations, without concern for the chemistry involved. Also certain thermodynamic properties are determined as byproducts of the main calculations.

International symposium on in vivo body composition studies: Program and abstracts

Energy Technology Data Exchange (ETDEWEB)

1986-01-01

This booklet contains the program and individual abstracts for papers presented at the International symposium on in vivo body composition studies. The presentations were divided into five sessions. Individual abstracts were indexed for the Energy Data Base. (DT)

CHAP: a composite nuclear plant simulation program applied to the 3000 MW(t) HTGR

International Nuclear Information System (INIS)

Secker, P.A.; Bailey, P.G.; Gilbert, J.S.; Willcutt, G.J.E. Jr.; Vigil, J.C.

1977-01-01

The Composite HTGR Analysis Program (CHAP) is a general systems analysis program which has been developed at LASL. The program is being used for simulating large HTGR nuclear power plant operation and accident transients. The general features and analytical methods of the CHAP program are discussed. Features of the large HTGR model and results of model transients are also presented

DETERMINING THE COMPOSITION OF HIGH TEMPERATURE COMBUSTION PRODUCTS OF FOSSIL FUEL BASED ON VARIATIONAL PRINCIPLES AND GEOMETRIC PROGRAMMING

Directory of Open Access Journals (Sweden)

Velibor V Vujović

2011-01-01

Full Text Available This paper presents the algorithm and results of a computer program for calculation of complex equilibrium composition for the high temperature fossil fuel combustion products. The method of determining the composition of high temperatures combustion products at the temperatures appearing in the open cycle MHD power generation is given. The determination of combustion product composition is based on minimization of the Gibbs free energy. The number of equations to be solved is reduced by using variational principles and a method of geometric programming and is equal to the sum of the numbers of elements and phases. A short description of the computer program for the calculation of the composition and an example of the results are also given.

Exercise program affects body composition but not weight in postmenopausal women

NARCIS (Netherlands)

Velthuis, M.J.; Schuit, A.J.; Peeters, P.H.; Monninkhof, E.M.

2009-01-01

OBJECTIVE: The aim of this study was to investigate the effect of a 12-month moderate-to-vigorous exercise program combining aerobic and muscle strength training on body composition among sedentary, postmenopausal women. METHODS: A randomized controlled trial was conducted. A total of 189 sedentary

Using Wild Olives in Breeding Programs: Implications on Oil Quality Composition

Directory of Open Access Journals (Sweden)

Lorenzo León

2018-02-01

Full Text Available A wide genetic diversity has been reported for wild olives, which could be particularly interesting for the introgression of some agronomic traits and resistance to biotic and abiotic stresses in breeding programs. However, the introgression of some beneficial wild traits may be paralleled by negative effects on some other important agronomic and quality traits. From the quality point of view, virgin olive oil (VOO from olive cultivars is highly appreciated for its fatty acid composition (high monounsaturated oleic acid content and the presence of several minor components. However, the composition of VOO from wild origin and its comparison with VOO from olive cultivars has been scarcely studied. In this work, the variability for fruit characters (fruit weight and oil content, OC, fatty acid composition, and minor quality components (squalene, sterols and tocopherols content and composition was studied in a set of plant materials involving three different origins: wild genotypes (n = 32, cultivars (n = 62 and genotypes belonging to cultivar × wild progenies (n = 62. As expected, values for fruit size and OC in wild olives were lower than those obtained in cultivated materials, with intermediate values for cultivar × wild progenies. Wild olives showed a remarkably higher C16:0 percentage and tocopherol content in comparison to the cultivars. Contrarily, lower C18:1 percentage, squalene and sterol content were found in the wild genotypes, while no clear differences were found among the different plant materials regarding composition of the tocopherol and phytosterol fractions. Some common highly significant correlations among components of the same chemical family were found in all groups of plant materials. However, some other correlations were specific for one of the groups. The results of the study suggested that the use of wild germplasm in olive breeding programs will not have a negative impact on fatty acid composition, tocopherol content

The Glasgow Parallel Reduction Machine: Programming Shared-memory Many-core Systems using Parallel Task Composition

Directory of Open Access Journals (Sweden)

Ashkan Tousimojarad

2013-12-01

Full Text Available We present the Glasgow Parallel Reduction Machine (GPRM, a novel, flexible framework for parallel task-composition based many-core programming. We allow the programmer to structure programs into task code, written as C++ classes, and communication code, written in a restricted subset of C++ with functional semantics and parallel evaluation. In this paper we discuss the GPRM, the virtual machine framework that enables the parallel task composition approach. We focus the discussion on GPIR, the functional language used as the intermediate representation of the bytecode running on the GPRM. Using examples in this language we show the flexibility and power of our task composition framework. We demonstrate the potential using an implementation of a merge sort algorithm on a 64-core Tilera processor, as well as on a conventional Intel quad-core processor and an AMD 48-core processor system. We also compare our framework with OpenMP tasks in a parallel pointer chasing algorithm running on the Tilera processor. Our results show that the GPRM programs outperform the corresponding OpenMP codes on all test platforms, and can greatly facilitate writing of parallel programs, in particular non-data parallel algorithms such as reductions.

Safer Roads: Comparisons Between Road Assessment Program and Composite Road Safety Index Method

Directory of Open Access Journals (Sweden)

Mohd Razelan Intan Suhana

2017-01-01

Full Text Available In most countries, crash statistics have becoming very crucial in evaluating road’s safety level. In Malaysia, these data are very important in deciding crash-prone areas known as black spot where specific road improvements plan will be proposed. However due to the unavailability of reliable crash data in many developing countries, appropriate road maintenance measures are facing great troubles. In light of that, several proactive methods in defining road’s safety level such as Road Assessment Program (RAP have emerged. This research aim to compare two proactive methods that have been tested in Malaysian roads ; road assessment program and road environment risk index which was developed based on composite index theory in defining road’s safety level. Composite road environment risk index was combining several crucial environment indicators, assigning weight and aggregating the individual index together to form a single value representing the road’s safety level. Based on the results, it can be concluded that both road assessment program and composite road environment risk index are contradicted in six different ways such as type of speed used, type of analysis used and their final outcomes. However, with an aim to promote safer roads, these two methods can be used concurrently as the outcomes in both methods seems to fulfil each other’s gap very well.

MAXIMSUPER: a computer program to assist in the design of multifilamentary superconducting composites

International Nuclear Information System (INIS)

Hoard, R.W.; Scanlan, R.M.; Hirzel, D.G.

1979-01-01

The strain degradation of critical current density has been analytically and experimentally investigated for multifilamentary superconducting composites produced in a bronze core geometry. Analytic results were obtained from a computer program (MAXIMSUPER) which predicts the stresses and strains in composites as a result of thermal and axial loading. Tensile test data for Nb 3 Sn are described. It is believed that the strain dependence of the critical current found in Nb 3 Sn is due to strain enhanced martensitic transformation

Fracture toughness and reliability in high-temperature structural ...

Indian Academy of Sciences (India)

Unknown

advanced propulsion systems, such as gas turbine engines .... cing current commercial high strength SiC fibres such as. Nicalon ... of the polymer pyrolysis technique to produce CFCC. ... tural applications in aerospace, military, and industrial.

An after-school exercise program improves fitness, and body composition in elementary school children.

Science.gov (United States)

Carrel, Aaron L; Logue, Julie; Deininger, Heidi; Clark, R Randall; Curtis, Vanessa; Montague, Paul; Baldwin, Sharon

2011-07-01

Reduced cardiovascular fitness (CVF) is a risk factor for obesity and cardiovascular disease. It has previously shown that a school-based fitness curriculum can improve CVF, and other health indicators in middle school aged children. Whether an afterschool program improves CVF and other health markers in elementary-school children is unresolved. The objective of this study was therefore to determine whether an on-site afterschool-based fitness program improves body composition, cardiovascular fitness level, in elementary school children. 80 elementary school children were evaluated in a "fitness-oriented" afterschool program managed by the local YMCA. Children underwent evaluation of cardiovascular fitness by maximal VO 2 treadmill testing and body composition by dual x-ray absorptiometry (DXA), at baseline (prior to the school-year) and again at end of the school year. Findings revealed that, at baseline, children had a mean age of 8.8 years, BMI of 18.7± 3, with a maximal VO 2 of 40.03 ± 7.6 ml/kg/min, and percent body fat of 28.7 ± 7%. After a 9-month intervention, children maximal VO 2 increased to 44.8 ± 7.5 ml/kg/min (p=0.04) and percent body fat decreased to 25.8 ± 6.2% (p=0.033). The study concluded that on-site afterschool programming focusing on fitness improved body composition and cardiovascular fitness, in elementary school children. Combined with prior studies, these data demonstrate that afterschool-based fitness curricula can benefit both obese and non-obese children. It was therefore recommended that, partnerships with schools to promote fitness even outside of school time should be a part of a school approach to improving children's health.

Floating Foundations: "Kairos," Community, and a Composition Program in Post-Katrina New Orleans

Science.gov (United States)

Johnson, T. R.; Letter, Joe; Livingston, Judith Kemerait

2009-01-01

The authors describe their individual and collective experiences reconstructing their New Orleans-based university composition program in the aftermath of Hurricane Katrina. They emphasize how the concept of "floating foundations" helps account for changes in their students' interests, and they suggest that this idea is applicable to the…

NASA Small Business Innovation Research Program. Composite List of Projects, 1983 to 1989

Science.gov (United States)

1990-01-01

The NASA SBIR Composite List of Projects, 1983 to 1989, includes all projects that have been selected for support by the Small Business Innovation Research (SBIR) Program of NASA. The list describes 1232 Phase 1 and 510 Phase 2 contracts that had been awarded or were in negotiation for award in August 1990. The main body is organized alphabetically by name of the small businesses. Four indexes cross-reference the list. The objective of this listing is to provide information about the SBIR program to anyone concerned with NASA research and development activities.

Computer Program for Calculation of Complex Chemical Equilibrium Compositions and Applications II. Users Manual and Program Description. 2; Users Manual and Program Description

Science.gov (United States)

McBride, Bonnie J.; Gordon, Sanford

1996-01-01

This users manual is the second part of a two-part report describing the NASA Lewis CEA (Chemical Equilibrium with Applications) program. The program obtains chemical equilibrium compositions of complex mixtures with applications to several types of problems. The topics presented in this manual are: (1) details for preparing input data sets; (2) a description of output tables for various types of problems; (3) the overall modular organization of the program with information on how to make modifications; (4) a description of the function of each subroutine; (5) error messages and their significance; and (6) a number of examples that illustrate various types of problems handled by CEA and that cover many of the options available in both input and output. Seven appendixes give information on the thermodynamic and thermal transport data used in CEA; some information on common variables used in or generated by the equilibrium module; and output tables for 14 example problems. The CEA program was written in ANSI standard FORTRAN 77. CEA should work on any system with sufficient storage. There are about 6300 lines in the source code, which uses about 225 kilobytes of memory. The compiled program takes about 975 kilobytes.

The Novel Attempt for Finding Minimum Solution in Fuzzy Neutrosophic Relational Geometric Programming (FNRGP with (max,min Composition

Directory of Open Access Journals (Sweden)

Huda E. Khalid

2016-08-01

Full Text Available This article sheds light on the possibility of finding the minimum solution set of neutrosophic relational geometric programming with (max, min composition. This work examines the privacy enjoyed by both neutrosophic logic and geometric programming, and how it affects the minimum solutions.

MASBAL: A computer program for predicting the composition of nuclear waste glass produced by a slurry-fed ceramic melter

International Nuclear Information System (INIS)

Reimus, P.W.

1987-07-01

This report is a user's manual for the MASBAL computer program. MASBAL's objectives are to predict the composition of nuclear waste glass produced by a slurry-fed ceramic melter based on a knowledge of process conditions; to generate simulated data that can be used to estimate the uncertainty in the predicted glass composition as a function of process uncertainties; and to generate simulated data that can be used to provide a measure of the inherent variability in the glass composition as a function of the inherent variability in the feed composition. These three capabilities are important to nuclear waste glass producers because there are constraints on the range of compositions that can be processed in a ceramic melter and on the range of compositions that will be acceptable for disposal in a geologic repository. MASBAL was developed specifically to simulate the operation of the West Valley Component Test system, a commercial-scale ceramic melter system that will process high-level nuclear wastes currently stored in underground tanks at the site of the Western New York Nuclear Services Center (near West Valley, New York). The program is flexible enough, however, to simulate any slurry-fed ceramic melter system. 4 refs., 16 figs., 5 tabs

Development of APDL program for analysis of composite material multicell beams

International Nuclear Information System (INIS)

Tariq, M.M.; Pasha, M.; Ahmed, M.N.; Munir, A.

2011-01-01

Comparison of finite elements and comparison of ANSYS with MSC Patran Nastran, for analysis of composite material multicell beams, is the main idea of this paper. The Finite Element Analysis (FEA) is a valuable tool of modeling and simulation in development, processing, production and application of modern hi-tech materials and structures for reliable design. Multicell beams have important industrial applications in the automotive and aerospace sectors. ANSYS Parametric Design Language (APDL) is an important language in parametric modeling and analysis of structures with simple to complex geometry. Its major advantage is virtual prototyping which can be used to analyze and compare different materials. This work introduces core techniques required for APDL using the case study of composite multicell beams subjected to constrained torsional loading. The published results using MSC NASTRAN have been verified using ANSYS and the corresponding arising issues and notes are the focus of this research study. The details of geometry, material and boundary conditions have been explained in order to construct Finite Element (FE) model. This FE model was simulated several times in ANSYS by the authors using various options of APDL language. A step-wise flowchart was used to detect and reduce problems in iterations of analysis in APDL programming. Results of FEA largely depend on FE model and software used. These issues become prominent while trying to verify results of MSC NASTRAN with ANSYS. The author has introduced three error criteria to select an equivalent finite element of one FEA package (ANSYS) for an equivalent element of other FEA package (MSC NASTRAN). These criteria are the relative error criterion, the absolute error criterion and the combined error criterion. The results from this research provide an insight into finite elements for reliability in design of composite materials. The practical milestones for research to develop FE model and APDL programs related

An Analysis of Programming Beginners' Source Programs

Science.gov (United States)

Matsuyama, Chieko; Nakashima, Toyoshiro; Ishii, Naohiro

The production of animations was made the subject of a university programming course in order to make students understand the process of program creation, and so that students could tackle programming with interest. In this paper, the formats and composition of the programs which students produced were investigated. As a result, it was found that there were a lot of problems related to such matters as how to use indent, how to apply comments and functions etc. for the format and the composition of the source codes.

In Vivo and In Vitro Genotoxic and Epigenetic Effects of Two Types of Cola Beverages and Caffeine: A Multiassay Approach

Directory of Open Access Journals (Sweden)

Marcos Mateo-Fernández

2016-01-01

Full Text Available The aim of this work was to assess the biological and food safety of two different beverages: Classic Coca Cola™ (CCC and Caffeine-Free Coca Cola (CFCC. To this end, we determined the genotoxicological and biological effects of different doses of lyophilised CCC and CFCC and Caffeine (CAF, the main distinctive constituent. Their toxic/antitoxic, genotoxic/antigenotoxic, and chronic toxicity (lifespan assay effects were determined in vivo using the Drosophila model. Their cytotoxic activities were determined using the HL-60 in vitro cancer model. In addition, clastogenic DNA toxicity was measured using internucleosomal fragmentation and SCGE assays. Their epigenetic effects were assessed on the HL-60 methylation status using some repetitive elements. The experimental results showed a slight chemopreventive effect of the two cola beverages against HL-60 leukaemia cells, probably mediated by nonapoptotic mechanisms. Finally, CCC and CAF induced a global genome hypomethylation evaluated in LINE-1 and Alu M1 repetitive elements. Overall, we demonstrated for the first time the safety of this famous beverage in in vivo and in vitro models.

In Vivo and In Vitro Genotoxic and Epigenetic Effects of Two Types of Cola Beverages and Caffeine: A Multiassay Approach.

Science.gov (United States)

Mateo-Fernández, Marcos; Merinas-Amo, Tania; Moreno-Millán, Miguel; Alonso-Moraga, Ángeles; Demyda-Peyrás, Sebastián

2016-01-01

The aim of this work was to assess the biological and food safety of two different beverages: Classic Coca Cola™ (CCC) and Caffeine-Free Coca Cola (CFCC). To this end, we determined the genotoxicological and biological effects of different doses of lyophilised CCC and CFCC and Caffeine (CAF), the main distinctive constituent. Their toxic/antitoxic, genotoxic/antigenotoxic, and chronic toxicity (lifespan assay) effects were determined in vivo using the Drosophila model. Their cytotoxic activities were determined using the HL-60 in vitro cancer model. In addition, clastogenic DNA toxicity was measured using internucleosomal fragmentation and SCGE assays. Their epigenetic effects were assessed on the HL-60 methylation status using some repetitive elements. The experimental results showed a slight chemopreventive effect of the two cola beverages against HL-60 leukaemia cells, probably mediated by nonapoptotic mechanisms. Finally, CCC and CAF induced a global genome hypomethylation evaluated in LINE-1 and Alu M1 repetitive elements. Overall, we demonstrated for the first time the safety of this famous beverage in in vivo and in vitro models.

Changes in body composition in heart failure patients after a resistance exercise program and branched chain amino acid supplementation.

Science.gov (United States)

Pineda-Juárez, Juan Antonio; Sánchez-Ortiz, Néstor Alonso; Castillo-Martínez, Lilia; Orea-Tejeda, Arturo; Cervantes-Gaytán, Rocío; Keirns-Davis, Candace; Pérez-Ocampo, Carlos; Quiroz-Bautista, Karla; Tenorio-Dupont, Mónica; Ronquillo-Martínez, Alberto

2016-02-01

Heart Failure (HF) is a complex syndrome, which can include the physiological, neural hormonal and metabolic complications known as "Cardiac Cachexia" (CC). In the development of CC there is a release of catabolic cytokines (Tumor Necrosis Factor-α, interleukins 1 and 6) that cause a decrease of fat free mass and fat mass. These changes in body composition might be reversed with a therapeutic combination of resistance exercise and branched chain amino acid supplementation (BCAA). Evaluate changes in body composition after a resistance exercise program and BCAA supplementation in patients with HF. In a randomized clinical trial with 3 month of follow-up anthropometric body composition analysis and stress tests were evaluated at the beginning and in the end of the study. Patients were divided into two groups; the experimental group performed the resistance exercise program and received 10 g/day BCAA supplementation, and the control group only performed the resistance exercise program. Both groups were provided with individualized diets and conventional medical treatment. Changes were found in hip circumference between the groups (p = 0.02), and muscle strength was increased in the experimental group (8%) and the control group (11.4%) with no difference between them. METS and VO2Max also increased in experimental and control groups (16.6% and 50.1% respectively). Regarding changes in symptoms, improvements in fatigue (45.4%), decubitus intolerance (21.8%) and dyspnea (25.4%) were observed in the overall sample. Improvements in physical and functional capacities are attributed to resistance exercise program but not to the BCAA supplementation. NCT02240511. Copyright © 2015 Elsevier Ltd and European Society for Clinical Nutrition and Metabolism. All rights reserved.

A Generator for Composition Interpreters

DEFF Research Database (Denmark)

Steensgaard-Madsen, Jørgen

1997-01-01

programming language design, specification and implementation then apply. A component can be considered as defining objects or commands according to convenience. A description language including type information provides sufficient means to describe component interaction according to the underlying abstract......Composition of program components must be expressed in some language, and late composition can be achieved by an interpreter for the composition language. A suitable notion of component is obtained by identifying it with the semantics of a generalised structured command. Experiences from...

Advanced organic composite materials for aircraft structures: Future program

Science.gov (United States)

1987-01-01

Revolutionary advances in structural materials have been responsible for revolutionary changes in all fields of engineering. These advances have had and are still having a significant impact on aircraft design and performance. Composites are engineered materials. Their properties are tailored through the use of a mix or blend of different constituents to maximize selected properties of strength and/or stiffness at reduced weights. More than 20 years have passed since the potentials of filamentary composite materials were identified. During the 1970s much lower cost carbon filaments became a reality and gradually designers turned from boron to carbon composites. Despite progress in this field, filamentary composites still have significant unfulfilled potential for increasing aircraft productivity; the rendering of advanced organic composite materials into production aircraft structures was disappointingly slow. Why this is and research and technology development actions that will assist in accelerating the application of advanced organic composites to production aircraft is discussed.

CREST : a computer program for the calculation of composition dependent self-shielded cross-sections

International Nuclear Information System (INIS)

Kapil, S.K.

1977-01-01

A computer program CREST for the calculation of the composition and temperature dependent self-shielded cross-sections using the shielding factor approach has been described. The code includes the editing and formation of the data library, calculation of the effective shielding factors and cross-sections, a fundamental mode calculation to generate the neutron spectrum for the system which is further used to calculate the effective elastic removal cross-sections. Studies to explore the sensitivity of reactor parameters to changes in group cross-sections can also be carried out by using the facility available in the code to temporarily change the desired constants. The final self-shielded and transport corrected group cross-sections can be dumped on cards or magnetic tape in a suitable form for their direct use in a transport or diffusion theory code for detailed reactor calculations. The program is written in FORTRAN and can be accommodated in a computer with 32 K work memory. The input preparation details, sample problem and the listing of the program are given. (author)

Correction of heterogeneities in the issue compositions in the construction plans optimized in radiotherapy using linear programming

International Nuclear Information System (INIS)

Viana, Rodrigo Sartorelo S.; Lima, Ernesto A.B.F.; Florentino, Helenice de Oliveira; Fonseca, Paulo Roberto da; Homem, Thiago Pedro Donadon

2009-01-01

Linear programming models are widely found in the literature addressing various aspects involved in the creation of optimized planning for radiotherapy. However, most mathematical formulations does not incorporate certain factors that are of extreme importance for the formulation of a real planning like the attenuation of the beam of radiation and heterogeneity in the composition of tissue irradiated. In this context are proposed in this paper some modifications in the formulation of a linear programming problem with the objective of making the simulation closer to the real planning for radiotherapy and thus enable a more reliable and comprehensive planning requirements. (author)

The impact of a 12-week resistance training program on strength, body composition, and self-concept of Hispanic adolescents.

Science.gov (United States)

Velez, Amelia; Golem, Devon L; Arent, Shawn M

2010-04-01

Current evidence suggests that a resistance training program may be physically and psychologically beneficial for adolescents. The purpose of this study was to examine the effects of a structured resistance training program on strength, body composition, and self-concept in normal and overweight Hispanic adolescents. Male and female participants (n = 28; 16.1 +/- 0.2 y; 164.5 +/- 1.4 cm; 63.3 +/- 2.5 kg; 20.0 +/- 1.7% body fat [BF]) were recruited from a predominantly Hispanic high school. Prior to the 12-week program, strength, body composition, and self-concept were assessed. Subjects were randomly assigned to a control group (CON; n = 15) or to a resistance training group (RT; n = 13) that participated in supervised strength training 3 days/week. All measures were repeated at the end of the 12-week program. RT had significantly greater strength increases for bench press (p increased %BF. RT had an increase in condition/stamina competence (p = 0.008), attractive body adequacy (p = 0.017), and global self-worth (p = 0.013) from pretest to posttest, whereas no change was observed for CON. In conclusion, resistance training resulted in significant physiological and psychological improvements in Hispanic adolescents compared to typical school-based activities. These findings indicate that resistance training can be incorporated into the activities of Hispanic adolescents to promote improved health and fitness.

Aspect-Oriented Programming using Composition Filters

NARCIS (Netherlands)

Aksit, Mehmet; Tekinerdogan, B.

1998-01-01

Software engineers may experience problems in modeling certain aspects while applying object-oriented techniques [4, 10, 11]. Composition-Filters are capable of expressing various different kinds of aspects in a uniform manner. These aspects are, for example, inheritance and delegation [1] and

The Effect of a Comprehensive Lifestyle Modification Program on Glycemic Control and Body Composition in Patients with Type 2 Diabetes

Directory of Open Access Journals (Sweden)

Ji-Soo Yoo, PhD, RN

2007-09-01

Conclusion: CLMP is a useful program, and its multiple approaches by nurses as the leaders and coordinators appear to have positive and synergistic roles in improving and maintaining stable glucose level and body composition in patients with type 2 diabetes.

Effects of a 2-Year Supervised Exercise Program Upon the Body Composition and Muscular Performance of HIV-Infected Patients

Science.gov (United States)

Paes, Lorena da Silva; Borges, Juliana Pereira; dos Santos, Fernanda Monteiro; de Oliveira, Taciana Pinto; Dupin, Jaciara Gomes; Harris, Elizabeth Assumpção; Farinatti, Paulo

2015-01-01

Background : There is a lack of research investigating long-term effects of exercise training upon the body composition and muscle function in HIV-infected patients (PHIV). The study investigated the influence of a 2-year supervised exercise program on body composition and strength of PHIV under highly active antiretroviral therapy (HAART). Methods : A training program including aerobic, strength and flexibility exercises was performed by 27 PHIV (17 men/ 10 women; age: 48.7±7.0 years; HAART: 150.7±65.3 months) during 1 year and 18 PHIV (10 men/ 8 women; age: 50.6±5.2 years; HAART: 176.6±53.1 months) during 2 years. Body composition and knee isokinetic strength were assessed at baseline and at the end of each year of intervention. Results : Body composition remained stable along the whole experiment vs baseline (1-year - total muscle mass: Δ men=1.1%, P=0.21; Δ women=1.4%, P=0.06; trunk fat: Δ men=-0.1%, P=0.65; Δ women=-1.5%, P=0.45; 2 years - total muscle mass: Δ men=2.7%, P=0.54; Δ women=-1.9%, P=0.71; trunk fat: Δ men=4.4%, P=0.96; Δ women=10.0%, P=0.30). After 1-year, peak torque increased in men (Δ extension=4.2%, P=0.01; Δ flexion=12.2%, P=0.04) and total work reduced in women (Δ extension=-15.4%, P=0.01, Δ flexion=-17.5%, P=0.05). All strength markers remained stable vs baseline after 2 years of intervention (P>0.05). Only men showed significant reduction in the risk of disability due to sarcopenia (P=0.05) after 1 year of intervention, which remained stable after 2 years. Conclusion : Long-term exercise training preserved strength and muscle mass in PHIV under HAART. Exercise programs should be part of HIV therapy to prevent sarcopenia of this population along the years. Trial Registration : ACTRN12610000683033; UTN U1111-1116-4416. PMID:26587076

A Review Of Nutritional Guidelines And Menu Compositions For School Feeding Programs In 12 Countries.

Directory of Open Access Journals (Sweden)

Ruzky eAliyar

2015-08-01

Full Text Available Study objectives: To analyze the nutritional guidelines and menu compositions of school meal provision in various different countries.Background: School feeding is the provision of food on-site or to take home, which aims to increase school enrolment, attendance and retention, and exist as a social safety net for households with very low income. Home-grown school feeding (HGSF, additionally, aims to stimulate local economies by providing a source of income for local smallholder farmers. Methods: Literature searches using the Ovid MEDLINE databases, gathered information from in-country stakeholders, and accessed the programme websites of various countries. Nutrient composition of these menus was calculated from nutritional guidelines and menu compositions using a nutrition linear programming tool (NUTVAL.Country comparisons: School feeding aims differ between countries of each income group. The implementation, delivery of service and nutritional content of foods also differ considerably between countries and income groups. In high-income countries, guidelines and standards have been recommended in an attempt to combat rising levels of overweight and obesity, and to model healthier lifestyle habits. In low-income countries there is a gap in terms of guidance on nutrition standards and menu composition.Conclusions: Provision of evidence-based guidance on nutrition standards to middle and low income countries who have recently established or are planning to establish school feeding has the potential to greatly enhance and improve the quality of service and improve the life of millions of children worldwide.

Shape memory-based tunable resistivity of polymer composites

Energy Technology Data Exchange (ETDEWEB)

Luo, Hongsheng, E-mail: hongshengluo@163.com [Faculty of Chemical Engineering and Light Industry, Guangdong University of Technology, Guangzhou 510006 (China); Zhou, Xingdong; Ma, Yuanyuan [Faculty of Chemical Engineering and Light Industry, Guangdong University of Technology, Guangzhou 510006 (China); Yi, Guobin, E-mail: ygb116@163.com [Faculty of Chemical Engineering and Light Industry, Guangdong University of Technology, Guangzhou 510006 (China); Cheng, Xiaoling [Faculty of Chemical Engineering and Light Industry, Guangdong University of Technology, Guangzhou 510006 (China); Zhu, Yong [Shanghai Hiend Polyurethane Inc., No. 389, Jinshan District, Shanghai (China); Zu, Xihong; Zhang, Nanjun; Huang, Binghao; Yu, Lifang [Faculty of Chemical Engineering and Light Industry, Guangdong University of Technology, Guangzhou 510006 (China)

2016-02-15

Graphical abstract: Hybrid nanofillers of the CNTs and AgNPs were embedded into a shape memory polyurethane. The composites exhibited tunable conduction, which could be facially tailored by the compositions and the thermal–mechanical programming. - Highlights: • Electrically conductive polymer composites in bi-layer structure were fabricated. • The CNTs/AgNPs layer had influence on the mechanics and thermal transitions. • The conductivity could be facially tailored via a thermo-mechanical programming. • The AgNPs contents enlarged the gauge factor of the resistivity–strain curves. • Tunneling theory was suitable for simulating the strain-dependent behaviors. - Abstract: A conductive composite in bi-layer structure was fabricated by embedding hybrid nanofillers, namely carbon nanotubes (CNTs) and silver nanoparticles (AgNPs), into a shape memory polyurethane (SMPU). The CNT/AgNP-SMPU composites exhibited a novel tunable conductivity which could be facially tailored in wide range via the compositions or a specifically designed thermo-mechanical shape memory programming. The morphologies of the conductive fillers and the composites were investigated by scanning electron microscope (SEM). The mechanical and thermal measurements were performed by tensile tests and differential scanning calorimetry (DSC). By virtue of a specifically explored shape memory programming, the composites were stretched and fixed into different temporary states. The electrical resistivity (R{sub s}) varied accordingly, which was able to be stabilized along with the shape fixing. Theoretical prediction based upon the tunneling model was performed. The R{sub s}–strain curves of the composites with different compositions were well fitted. Furthermore, the relative resistivity and the Gauge factor along with the elongation were calculated. The influence of the compositions on the strain-dependent R{sub s} was disclosed. The findings provided a new avenue to tailor the conductivity

Composite fabrication via resin transfer molding technology

Energy Technology Data Exchange (ETDEWEB)

Jamison, G.M.; Domeier, L.A.

1996-04-01

The IMPReS (Integrated Modeling and Processing of Resin-based Structures) Program was funded in FY95 to consolidate, evaluate and enhance Sandia`s capabilities in the design and fabrication of composite structures. A key driver of this and related programs was the need for more agile product development processes and for model based design and fabrication tools across all of Sandia`s material technologies. A team of polymer, composite and modeling personnel was assembled to benchmark Sandia`s existing expertise in this area relative to industrial and academic programs and to initiate the tasks required to meet Sandia`s future needs. RTM (Resin Transfer Molding) was selected as the focus composite fabrication technology due to its versatility and growing use in industry. Modeling efforts focused on the prediction of composite mechanical properties and failure/damage mechanisms and also on the uncured resin flow processes typical of RTM. Appropriate molds and test composites were fabricated and model validation studies begun. This report summarizes and archives the modeling and fabrication studies carried out under IMPReS and evaluates the status of composite technology within Sandia. It should provide a complete and convenient baseline for future composite technology efforts within Sandia.

The effects of a reformer Pilates program on body composition and morphological characteristics in active women after a detraining period.

Science.gov (United States)

Vaquero-Cristóbal, Raquel; Alacid, Fernando; Esparza-Ros, Francisco; López-Plaza, Daniel; Muyor, José M; López-Miñarro, Pedro A

2016-10-01

The aim of this quasi-experimental pilot study was to explore the effects of a reformer Pilates program on the anthropometry, body composition, and somatotype of active adult women after a short non-exercise period. Twenty-eight women (mean age: 40.21 ± standard deviation of 8.12 years old) with one to three years of reformer Pilates experience participated in the study. The women participated in a reformer Pilates program for 16 weeks (one hour, twice per week) after 4 weeks of detraining (summer holidays) in 2012. The International Society for the Advancement of Kinanthropometry full profile was assessed before and after the intervention program. Significant decreases (p ≤ 0.05) from pre- to post-program were observed for triceps, iliac crest, supraspinale, abdominal, front thigh and medial calf skinfold thicknesses, six and eight skinfold thickness sums, forearm and ankle girths, waist/hip ratio, endomorphy, and fat mass. Significant increases (p ≤ .05) were observed for corrected arm, corrected calf girths, and muscle mass. Generally, women showed a mesomorphic endomorph (endomorphy predominant) and mesomorph-endomorph (endomorphy and mesomorphy predominant) in the pre- and posttests, respectively. In conclusion, the practice of reformer Pilates was associated with healthy changes in anthropometric parameters, body composition, and somatotype in Pilates-experienced women after 4 weeks of no physical exercise.

Computer Program for Calculation of Complex Chemical Equilibrium Compositions, Rocket Performance, Incident and Reflected Shocks, and Chapman-Jouguet Detonations. Interim Revision, March 1976

Science.gov (United States)

Gordon, S.; Mcbride, B. J.

1976-01-01

A detailed description of the equations and computer program for computations involving chemical equilibria in complex systems is given. A free-energy minimization technique is used. The program permits calculations such as (1) chemical equilibrium for assigned thermodynamic states (T,P), (H,P), (S,P), (T,V), (U,V), or (S,V), (2) theoretical rocket performance for both equilibrium and frozen compositions during expansion, (3) incident and reflected shock properties, and (4) Chapman-Jouguet detonation properties. The program considers condensed species as well as gaseous species.

Effects of a 5-month football program on perceived psychological status and body composition of overweight boys

DEFF Research Database (Denmark)

Seabra, A C; Seabra, A F; Brito, J

2014-01-01

The effects of a 5-month intervention of football instruction and practice on the perceived psychological status and body composition of overweight boys were examined. Twelve boys (8-12 years; body mass index ≥ 85th percentile) participated in a structured 5-month football program, consisting...... of four weekly 60-90 min sessions with mean heart rate > 80%HRmax [football group (FG)]. A control group (CG) included eight boys of equivalent age from an obesity clinic located in the same area as the school. Both groups participated in two sessions of 45-90-min physical education per week at school....... Indicators of perceived psychological status included body image, self-esteem, attraction to participation in physical activity, and perceived physical competence measured with standardized questionnaires. Body composition was evaluated using dual-energy X-ray absorptiometry. From baseline through 5 months...

Advanced Industrial Materials Program

Science.gov (United States)

Stooksbury, F.

1994-06-01

The mission of the Advanced Industrial Materials (AIM) program is to commercialize new/improved materials and materials processing methods that will improve energy efficiency, productivity, and competitiveness. Program investigators in the DOE national laboratories are working with about 100 companies, including 15 partners in CRDA's. Work is being done on intermetallic alloys, ceramic composites, metal composites, polymers, engineered porous materials, and surface modification. The program supports other efforts in the Office of Industrial Technologies to assist the energy-consuming process industries. The aim of the AIM program is to bring materials from basic research to industrial application to strengthen the competitive position of US industry and save energy.

Effects of a popular exercise and weight loss program on weight loss, body composition, energy expenditure and health in obese women

Directory of Open Access Journals (Sweden)

Magrans-Courtney Teresa

2009-05-01

Full Text Available Abstract Objective To determine the safety and efficacy of altering the ratio of carbohydrate and protein in low-energy diets in conjunction with a popular exercise program in obese women. Design Matched, prospective clinical intervention study to assess efficacy of varying ratios of carbohydrate and protein intake in conjunction with a regular exercise program. Participants One-hundred sixty one sedentary, obese, pre-menopausal women (38.5 ± 8.5 yrs, 164.2 ± 6.7 cm, 94.2 ± 18.8 kg, 34.9 ± 6.4 kg·m-2, 43.8 ± 4.2% participated in this study. Participants were weight stable and not participating in additional weight loss programs. Methods Participants were assigned to either a no exercise + no diet control (CON, a no diet + exercise group (ND, or one of four diet + exercise groups (presented as kcals; % carbohydrate: protein: fat: 1 a high energy, high carbohydrate, low protein diet (HED [2,600; 55:15:30%], 2 a very low carbohydrate, high protein diet (VLCHP [1,200 kcals; 63:7:30%], 3 a low carbohydrate, moderate protein diet (LCMP [1,200 kcals; 50:20:30%] and 4 a high carbohydrate, low protein diet (HCLP [1,200 kcals; 55:15:30%]. Participants in exercise groups (all but CON performed a pneumatic resistance-based, circuit training program under supervision three times per week. Measurements Anthropometric, body composition, resting energy expenditure (REE, fasting blood samples and muscular fitness assessments were examined at baseline and weeks 2, 10 and 14. Results All groups except CON experienced significant reductions (P P P P P Conclusion Exercise alone (ND appears to have minimal impact on measured outcomes with positive outcomes apparent when exercise is combined with a hypoenergetic diet. Greater improvements in waist circumference and body composition occurred when carbohydrate is replaced in the diet with protein. Weight loss in all diet groups (VLCHP, LCMP and HCLP was primarily fat and stimulated improvements in markers of

Multi-material Preforming of Structural Composites

Energy Technology Data Exchange (ETDEWEB)

Norris, Robert E. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Eberle, Cliff C. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Pastore, Christopher M. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Sudbury, Thomas Z. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Xiong, Fue [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Hartman, David [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2015-05-01

Fiber-reinforced composites offer significant weight reduction potential, with glass fiber composites already widely adopted. Carbon fiber composites deliver the greatest performance benefits, but their high cost has inhibited widespread adoption. This project demonstrates that hybrid carbon-glass solutions can realize most of the benefits of carbon fiber composites at much lower cost. ORNL and Owens Corning Reinforcements along with program participants at the ORISE collaborated to demonstrate methods for produce hybrid composites along with techniques to predict performance and economic tradeoffs. These predictions were then verified in testing coupons and more complex demonstration articles.

The effect of programmed exercise on body compositions and heart rate of 11-13 years-old male students

Directory of Open Access Journals (Sweden)

Mohammad H. Dashti

2011-11-01

Full Text Available Background: Different forms of physical activities can play a very important role in improving health and physical fitness. The purpose of this study was to examine the effect of the programmed exercise on students’ body compositions and heart rate at rest.Materials and Method: Two groups each consisting of 15students, aged averagely 12.6 years were the subjects of this experimental study. The experimental group in each session took part in an exercise program consisting of 20 minutes of aerobic activity (running, 10 minutes of aerobic exercise, 30 minutes of local training and 5 minutes of free exercise. The experiment last for 24 sessions. Control group didn’t do any special practice. In both groups, weight, fat mass, fat percentage, lean body mass and heart rate were measured during rest period before and after the experiment. Results: Results showed that the fat percentage, weight, fat mass and heart rate had decreased after 8 weeks of programmed exercise in the experimental group unlike the control group. However, no significant difference was observed in lean body mass.Conclusion: The exercise program used in this study may help loosing weight and make the heart stronger

The effects of an exercise training program on body composition and aerobic capacity parameters in Tunisian obese children

Directory of Open Access Journals (Sweden)

Sofien Regaieg

2013-01-01

Full Text Available Background: The prevalence of children obesity is rising alarmingly in both developed and developing countries. Developing effective exercise programs is a strategy for decreasing this prevalence and limiting obesity-associated long-term comorbidities. Objectives: To determine whether a 16-week training program; in addition to the school physical education and without dietary intervention; could have beneficial effects on body composition and aerobic capacity of obese children. Materials and Methods: Twenty-eight obese children (16 boys, 12 girls; aged 12-14 years were enrolled and were divided into either the exercise group (EG, n = 14 or the control group (CG, n = 14. EG participated in a 16-week aerobic exercises (four 60-min sessions per week at 70-85% of HRmax (maximum heart rate, in addition to the school physical education. Fat-Free Mass (FFM and Fat Mass (FM were assessed with bioelectrical impedance equipment. To assess aerobic capacity, maximal metabolic equivalent of task (METmax and maximal workload (Wmax were estimated with an electronically braked cycle ergometer (type Ergoline 500® . Results: At baseline, there were no differences between the two groups. After the training program, only the EG showed significant reduction in BMI (body mass index and waist circumference compared with the baseline values (P < 0.001. Exercise training significantly decreased FM only in the EG. A significant increase in FFM was seen in both groups; more marked in the EG. There was a significant increase in METmax (P < 0.05 and Wmax (P = 0.02 in the EG, and no significant changes in these parameters were seen in the CG. HRmax significantly decreased only in the EG (P < 0.05. Conclusion: This training program has beneficial effects on body composition and aerobic capacity parameters in obese children. Our intervention has the advantage of providing a sustainable and reproducible school and community approach for the management of children obesity.

A 12-week rehabilitation program improves body composition, pain sensation, and internal/external torques of baseball pitchers with shoulder impingement symptom.

Science.gov (United States)

Cha, Jun-Youl; Kim, Jae-Hak; Hong, Ju; Choi, Young-Tae; Kim, Min-Ho; Cho, Ji-Hyun; Ko, Il-Gyu; Jee, Yong-Seok

2014-02-01

The aim of this study was to investigate the effects of a 12-week rehabilitation program on body composition, shoulder pain, and isokinetic internal/external torques of pitchers with impingement syndrome. A total of 30 pitchers were divided into 2 groups: experimental group (EG, n = 16) and control group (CG, n= 14). The rehabilitation program consisted of physical therapy, warm-up, work-out, and cool-down. As results, body weight and fat mass of EG were decreased whereas muscle mass of EG was significantly increased after the experiment. The pain degrees in resting, normal daily activity, and strenuous activity on the numeric pain rating scale were significantly decreased in the EG. The internal and external peak torques (PTs) of uninvolved and involved sides of EG were increased in EG after 12 weeks. Such results provide a deficit ratio of both sides in EG close to normal values. The ratios of internal/external PTs in EG were also close to the reference values. The internal and external total works of both sides in EG were similar to the values of PT. The fatigue indices of internal and external rotators of both sides in EG were decreased. As a conclusion, a 12-week rehabilitation program reduced the shoulder pain, improved the body composition and enhanced the isokinetic shoulder internal/external rotators in EG with impingement symptoms. Also the study suggested that the rehabilitation program evened out the ratio between internal and external rotators and lowered the fatigue level after the experiment.

A social comparison theory analysis of group composition and efficacy of cancer support group programs.

Science.gov (United States)

Carmack Taylor, Cindy L; Kulik, James; Badr, Hoda; Smith, Murray; Basen-Engquist, Karen; Penedo, Frank; Gritz, Ellen R

2007-07-01

Group-based psychosocial programs provide an effective forum for improving mood and social support for cancer patients. Because some studies show more benefit for patients with initially high psychosocial distress, and little or no benefit for patients with initially low distress, support programs may better address patient needs by only including distressed patients. However, distressed patients may benefit particularly from the presence of nondistressed patients who model effective coping, an idea many researchers and extensions of social comparison theory support. We present a theoretical analysis, based on a social comparison perspective, of how group composition (heterogeneous group of distressed and nondistressed patients versus homogeneous group of distressed patients) may affect the efficacy of cancer support programs. We propose that a heterogeneous group allows distressed patients maximal opportunity for the various social comparison activities they are likely to prefer; a homogeneous group does not. Though the presence of nondistressed patients in a heterogeneous group potentially benefits distressed patients, the benefits for nondistressed patients are unclear. For nondistressed patients, heterogeneous groups may provide limited opportunities for preferred social comparison activity and may create the possibility for no benefit or even negative effects on quality of life. We also discuss ethical issues with enrolling nondistressed patients whose presence may help others, but whose likelihood of personal benefit is questionable.

[The effects of 16-weeks pilates mat program on anthropometric variables and body composition in active adult women after a short detraining period].

Science.gov (United States)

Vaquero-Cristóbal, Raquel; Alacid, Fernando; Esparza-Ros, Francisco; Muyor, José M; López-Miñarro, Pedro Ángel

2015-04-01

previous studies have analysed the effect of mat Pilates practice on anthropometric variables and body composition in sedentaries. To date no researchs have investigated the benefits of Pilates on these variables after a short detraining period. to determine the effect of a 16-week mat Pilates program on anthropometric variables, body composition and somatotype of women with previous practice experience after three weeks of detraining period. twenty-one women underwent a complete anthropometric assessment according with ISAK guidelines before and after a 16 week mat Pilates program (two days, one hour). All women had one to three years of mat Pilates experience and came to three weeks of detraining period (Christmas holiday). women showed significant decreases for body mass, BMI, upper limb (biceps and triceps) and trunk (subscapular, iliac crest, supraspinale and abdominal) individual skinfolds, 6 and 8 skinfold sums, endomorphy and fat mass; and a significant increases for muscle mass. The mean somatotype was classified as mesomorphic endomorph in the pre- (4.91, 4.01, 1.47) and post-test (4.68, 4.16, 1.69). Eight women changed their somatotype clasification after the intervention program. the practice of mat Pilates for 16 weeks caused changes associated with health state improvements on anthropometric variables, especially on skinfolds which significantly decreased, body composition (fat and muscle masses decreased and increased, respectively) and somatotype (there was a significantly decreased on the endomorph component in experienced women after three week of detraning. Copyright AULA MEDICA EDICIONES 2014. Published by AULA MEDICA. All rights reserved.

Composites materials: the technology of future

International Nuclear Information System (INIS)

Ahmed, M.N.; Memon, I.R.; Ahmad, F.; Zafar, N.

2001-01-01

Composite materials have a long history of usage. Their precise beginnings are not known; however all recorded history contains references to some form of composite material. e.g. straw was used by man to strengthen mud bricks thousands of years ago. This article presents the use of advanced composites materials in aircraft and space industry. Its brief history, use in military and civil aviation, use in space program, future usage, advantages in terms of cost, weight and strength. Use of composites in unmanned aerial vehicles and problems associated with usage of composites materials are also discussed. (author)

Fiscal 2000 achievement report on the venture business assisting type regional consortium - Core industry creation type. Development of technology for manufacturing large-size, optionally shapable, totally oxide type continuous fiber ceramic composite; 2000 nendo chiiki consortium kenkyu kaihatsu jigyo seika hokokusho. All oxide ogata nin'i keijo renzoku sen'i kyoka ceramics no seizo gijutsu kaihatsu

Energy Technology Data Exchange (ETDEWEB)

NONE

2001-03-01

This research and development endeavor is based on Tokyo University's technical seeds and aims to put on the market Al{sub 2}O{sub 3} based CFCC (continuous fiber ceramic composite) materials. They do not break down and are shapable into large or complicate forms as required, which features are not to be expected from a single ceramic material, and are usable in a high temperature oxidizing atmosphere. High purity alumina fiber and alumina-silica fiber containing 70% of Al{sub 2}O{sub 3} were selected, and woven. The resultant cloth was baked at a low temperature for burning away organic impurities. The cloth was then immersed in a zirconia sol containing 30wt% of the stock solution, and was allowed to dry at 105 degrees C. An alumina slurry was prepared containing a dispersant and a binder, and was applied to the zirconia-soaked cloth until it was as thick as desired. The cloth was kept at 800 degrees C for 1 hour for degreasing, and was baked at a low temperature where no heat caused degradation of the ceramic fiber would occur. Specimens stand long use when the temperature is 1,300 degrees or lower for high purity fiber and approximately 1,150 degrees or lower for alumina-silica fiber. They withstand 30-100MPa, dependent on the manufacturing conditions and the kind of fiber used. (NEDO)

The effect of a short-term high-intensity circuit training program on work capacity, body composition, and blood profiles in sedentary obese men: a pilot study.

Science.gov (United States)

Miller, Matthew B; Pearcey, Gregory E P; Cahill, Farrell; McCarthy, Heather; Stratton, Shane B D; Noftall, Jennifer C; Buckle, Steven; Basset, Fabien A; Sun, Guang; Button, Duane C

2014-01-01

The objective of this study was to determine how a high-intensity circuit-training (HICT) program affects key physiological health markers in sedentary obese men. Eight obese (body fat percentage >26%) males completed a four-week HICT program, consisting of three 30-minute exercise sessions per week, for a total of 6 hours of exercise. Participants' heart rate (HR), blood pressure (BP), rating of perceived exertion, total work (TW), and time to completion were measured each exercise session, body composition was measured before and after HICT, and fasting blood samples were measured before throughout, and after HICT program. Blood sample measurements included total cholesterol, triacylglycerides, high-density lipoprotein cholesterol, low-density lipoprotein cholesterol, glucose, and insulin. Data were analyzed by paired t-tests and one-way ANOVA with repeated measures. Statistical significance was set to P < 0.05. Data analyses revealed significant (P < 0.05) improvements in resting HR (16% decrease), systolic BP (5.5% decrease), TW (50.7%), fat tissue percentage (3.6%), lean muscle tissue percentage (2%), cholesterol (13%), triacylglycerol (37%), and insulin (18%) levels from before to after HICT program. Overall, sedentary obese males experienced a significant improvement in biochemical, physical, and body composition characteristics from a HICT program that was only 6 hours of the total exercise.

Compositional data types

DEFF Research Database (Denmark)

Bahr, Patrick; Hvitved, Tom

2011-01-01

-cut fusion style deforestation which yields considerable speedups. We demonstrate our framework in the setting of compiler construction, and moreover, we compare compositional data types with generic programming techniques and show that both are comparable in run-time performance and expressivity while our...

Building Face Composites Can Harm Lineup Identification Performance

Science.gov (United States)

Wells, Gary L.; Charman, Steve D.; Olson, Elizabeth A.

2005-01-01

Face composite programs permit eyewitnesses to build likenesses of target faces by selecting facial features and combining them into an intact face. Research has shown that these composites are generally poor likenesses of the target face. Two experiments tested the proposition that this composite-building process could harm the builder's memory…

Development of environmental consequence index (ECI) using fuzzy composite programming

International Nuclear Information System (INIS)

Arunraj, N.S.; Maiti, J.

2009-01-01

Estimation of environmental consequences of hazardous substances in chemical industries is a very difficult task owing to (i) diversity in the types of hazards and their effects, (ii) location, and (ii) uncertainty in input information. Several indices have been developed over the years to estimate the environmental consequences. In this paper, a critical literature review was done on the existing environmental indices to identify their applications and limitations. The existing indices lack in consideration of all environmental consequence factors such as material hazard factors, dispersion factors, environmental effects, and their uncertainty. A new methodology is proposed for the development of environmental consequence index (ECI), which can overcome the stated limitations. Moreover, the recently developed fuzzy composite programming (FCP) is used to take care of the uncertainty in estimation. ECI is applied to benzene extraction unit (BEU) of a petrochemical industry situated in eastern part of India. The ECI for all the eight sections of BEU are estimated and ranked. The results are compared with well-established indices such as Dow fire and explosion index, safety weight hazard index (SWeHI), and environmental accident index (EAI). The proposed ECI may outperform other indices based on its detailed consideration of the factors and performed equally to Dow F and E index, and EAI in most of the cases for the present application

Aspect oriented service composition for telecommunication applications

NARCIS (Netherlands)

Niemöller, Jörg

2016-01-01

This PhD dissertation investigates how to overcome the negative effects of cross cutting concerns in the development of composite service applications. It proposes a combination of dynamic aspect oriented programming with a rules driven service composition mechanism. This combination allows very

Future flare compositions

NARCIS (Netherlands)

Lingen, J.L.N. van; Meuken, D.; Hackspik, M.M.; Mäkeläinen, T.; Weiser, V.; Poulson, G.W.

2014-01-01

This poster describes the work done within the Category B joint research project under the European Defence Agency (EDA) on Future Flare Compositions [1]. Contributing members were Finland, Germany, United Kingdom and the Netherlands. The program was aimed to identify the technology gaps that apply

Design a computational program to calculate the composition variations of nuclear materials in the reactor operations

International Nuclear Information System (INIS)

Mohmmadnia, Meysam; Pazirandeh, Ali; Sedighi, Mostafa; Bahabadi, Mohammad Hassan Jalili; Tayefi, Shima

2013-01-01

Highlights: ► The atomic densities of light and heavy materials are calculated. ► The solution is obtained using Runge–Kutta–Fehlberg method. ► The material depletion is calculated for constant flux and constant power condition. - Abstract: The present work investigates an appropriate way to calculate the variations of nuclides composition in the reactor core during operations. Specific Software has been designed for this purpose using C#. The mathematical approach is based on the solution of Bateman differential equations using a Runge–Kutta–Fehlberg method. Material depletion at constant flux and constant power can be calculated with this software. The inputs include reactor power, time step, initial and final times, order of Taylor Series to calculate time dependent flux, time unit, core material composition at initial condition (consists of light and heavy radioactive materials), acceptable error criterion, decay constants library, cross sections database and calculation type (constant flux or constant power). The atomic density of light and heavy fission products during reactor operation is obtained with high accuracy as the program outputs. The results from this method compared with analytical solution show good agreements

Computer Music Synthesis and Composition

Science.gov (United States)

Ayers, Lydia

What is computer music composition? Composers are using the computer for everything from MIDI instruments communicating with computer sequencers, pitch trackers analyzing the sounds of acoustic instruments and converting them to pitch information, live performers with recorded music, performers with interactive computer programs, computer music produced by dancers using sensors, automatic music composition with the computer programs composing the music, composing with sounds or parts of sounds rather than notes, how to structure the use of time, composing with timbres, or the colors of sounds, and timbre morphing, such as a gong morphing to a voice, composing with textures and texture morphing, such as fluttertonguing morphing to pitch, granular synthesis, trills and convolution.

The Linguistic Memory of Composition and the Rhetoric and Composition PhD: Forgetting (and Remembering) Language and Language Difference in Doctoral Curricula

Science.gov (United States)

Kilfoil, Carrie Byars

2017-01-01

This article analyzes the decline of linguistics in rhetoric and composition PhD programs in terms of the "linguistic memory" (Trimbur) of composition. Since the field of linguistics once offered the primary means for composition to address the structural, psychological, sociohistorical, and cultural dimensions of language in student…

Structural dynamics of shroudless, hollow fan blades with composite in-lays

Science.gov (United States)

Aiello, R. A.; Hirschbein, M. S.; Chamis, C. C.

1982-01-01

Structural and dynamic analyses are presented for a shroudless, hollow titanium fan blade proposed for future use in aircraft turbine engines. The blade was modeled and analyzed using the composite blade structural analysis computer program (COBSTRAN); an integrated program consisting of mesh generators, composite mechanics codes, NASTRAN, and pre- and post-processors. Vibration and impact analyses are presented. The vibration analysis was conducted with COBSTRAN. Results show the effect of the centrifugal force field on frequencies, twist, and blade camber. Bird impact analysis was performed with the multi-mode blade impact computer program. This program uses the geometric model and modal analysis from the COBSTRAN vibration analysis to determine the gross impact response of the fan blades to bird strikes. The structural performance of this blade is also compared to a blade of similar design but with composite in-lays on the outer surface. Results show that the composite in-lays can be selected (designed) to substantially modify the mechanical performance of the shroudless, hollow fan blade.

Self-Healing Composite of Thermoset Polymer and Programmed Super Contraction Fibers

Science.gov (United States)

Li, Guoqiang (Inventor); Meng, Harper (Inventor)

2016-01-01

A composition comprising thermoset polymer, shape memory polymer to facilitate macro scale damage closure, and a thermoplastic polymer for molecular scale healing is disclosed; the composition has the ability to resolve structural defects by a bio-mimetic close-then heal process. In use, the shape memory polymer serves to bring surfaces of a structural defect into approximation, whereafter use of the thermoplastic polymer for molecular scale healing allowed for movement of the thermoplastic polymer into the defect and thus obtain molecular scale healing. The thermoplastic can be fibers, particles or spheres which are used by heating to a level at or above the thermoplastic's melting point, then cooling of the composition below the melting temperature of the thermoplastic. Compositions of the invention have the ability to not only close macroscopic defects, but also to do so repeatedly even if another wound/damage occurs in a previously healed/repaired area.

Advanced technology composite aircraft structures

Science.gov (United States)

Ilcewicz, Larry B.; Walker, Thomas H.

1991-01-01

Work performed during the 25th month on NAS1-18889, Advanced Technology Composite Aircraft Structures, is summarized. The main objective of this program is to develop an integrated technology and demonstrate a confidence level that permits the cost- and weight-effective use of advanced composite materials in primary structures of future aircraft with the emphasis on pressurized fuselages. The period from 1-31 May 1991 is covered.

Advanced composite elevator for Boeing 727 aircraft

Science.gov (United States)

1979-01-01

Detail design activities are reported for a program to develop an advanced composites elevator for the Boeing 727 commercial transport. Design activities include discussion of the full scale ground test and flight test activities, the ancillary test programs, sustaining efforts, weight status, and the production status. Prior to flight testing of the advanced composites elevator, ground, flight flutter, and stability and control test plans were reviewed and approved by the FAA. Both the ground test and the flight test were conducted according to the approved plan, and were witnessed by the FAA. Three and one half shipsets have now been fabricated without any significant difficulty being encountered. Two elevator system shipsets were weighed, and results validated the 26% predicted weight reduction. The program is on schedule.

Experimental investigation of defect criticality in FRP laminate composites

Science.gov (United States)

Joyce, Peter James

1999-11-01

This work examines the defect criticality of fiber reinforced polymer Composites. The objective is to determine the sensitivity of the finished composite to various process-induced defects. This work focuses on two different classes of process-induced defects; (1) fiber waviness in high performance carbon-fiber reinforced unidirectional composites and (2) void volume in low cost glass-fabric reinforced composites. The role of fiber waviness in the compressive response of unidirectional composites has been studied by a number of other investigators. Because of difficulties associated with producing real composites with varying levels of fiber waviness, most experimental studies of fiber waviness have evaluated composites with artificially induced fiber waviness. Furthermore, most experimental studies have been concentrated on the effects of out-of-plane fiber waviness. The objective of this work is to evaluate the effects of in-plane fiber waviness naturally occurring in autoclave consolidated thermoplastic laminates. The first phase of this project involved the development of a simple technique for measuring the resulting fiber waviness levels. An experimental investigation of the compression strength reduction in composites with in-plane fiber waviness followed. The experimental program included carbon-fiber reinforced thermoplastic composites manufactured from prepreg tape by hand layup, and carbon-fiber and glass-fiber reinforced composites manufactured from an experimental powder towpreg by filament winding and autoclave consolidation. The compression specimens exhibited kink band failure in the prepreg composite and varying amounts of longitudinal splitting and kink banding in the towpreg composites. The compression test results demonstrated the same trend as predicted by microbudding theory but the overall quantitative correlation was poor. The second thrust of this research evaluated void effects in resin transfer molded composites. Much of the existing

Composites and blends from biobased materials

Energy Technology Data Exchange (ETDEWEB)

Kelley, S.S. [National Renewable Energy Laboratory, Golden, CO (United States)

1995-05-01

The program is focused on the development of composites and blends from biobased materials to use as membranes, high value plastics, and lightweight composites. Biobased materials include: cellulose derivative microporous materials, cellulose derivative copolymers, and cellulose derivative blends. This year`s research focused on developing an improved understanding of the molecular features that cellulose based materials with improved properties for gas separation applications. Novel cellulose ester membrane composites have been developed and are being evaluated under a collaborative research agreement with Dow Chemicals Company.

Change in weight and body composition in obese subjects following a hypocaloric diet plus different training programs or physical activity recommendations.

Science.gov (United States)

Benito, Pedro J; Bermejo, Laura M; Peinado, Ana B; López-Plaza, Bricia; Cupeiro, Rocío; Szendrei, Barbara; Calderón, Francisco J; Castro, Eliane A; Gómez-Candela, Carmen

2015-04-15

The aim of the present study was to compare the effects of different physical activity programs, in combination with a hypocaloric diet, on anthropometric variables and body composition in obese subjects. Ninety-six obese (men: n = 48; women: n = 48; age range: 18-50 yr) participated in a supervised 22-wk program. They were randomized into four groups: strength training (S; n = 24), endurance training (E; n = 26), combined strength + endurance training (SE; n = 24), and physical activity recommendations (C; n = 22). In addition, all groups followed the same hypocaloric diet. At baseline and at the end of the intervention, dietetic and physical activity variables were assessed using validated questionnaires. Anthropometric variables were recorded along with body composition variables measured using dual-energy X-ray absorptiometry techniques. At the end of the intervention, significant improvements were seen within groups in terms of body weight (S: -9.21 ± 0.83 kg; E: -10.55 ± 0.80 kg; SE: -9.88 ± 0.85 kg; C: -8.69 ± 0.89 kg), and total fat mass (S: -5.24 ± 0.55%; E: -5.35 ± 0.55%; SE: -4.85 ± 0.56%; C: -4.89 ± 0.59%). No differences were seen between groups at this time in terms of any other anthropometric or body composition variables examined. All groups increased their total physical activity in metabolic equivalents (MET) per week during the intervention, but with no difference between groups (S: 976 ± 367 MET-min/wk; E: 954 ± 355 MET-min/wk; SE: 1 329 ± 345 MET-min/wk; C: 763 ± 410 MET-min/wk). This study shows that, when combined with a hypocaloric diet, exercise training and adherence to physical activity recommendations are equally effective at reducing body weight and modifying body composition in the treatment of obesity (Clinical Trials Gov. number: NCT01116856). Copyright © 2015 the American Physiological Society.

Stochastic-Strength-Based Damage Simulation of Ceramic Matrix Composite Laminates

Science.gov (United States)

Nemeth, Noel N.; Mital, Subodh K.; Murthy, Pappu L. N.; Bednarcyk, Brett A.; Pineda, Evan J.; Bhatt, Ramakrishna T.; Arnold, Steven M.

2016-01-01

The Finite Element Analysis-Micromechanics Analysis Code/Ceramics Analysis and Reliability Evaluation of Structures (FEAMAC/CARES) program was used to characterize and predict the progressive damage response of silicon-carbide-fiber-reinforced reaction-bonded silicon nitride matrix (SiC/RBSN) composite laminate tensile specimens. Studied were unidirectional laminates [0] (sub 8), [10] (sub 8), [45] (sub 8), and [90] (sub 8); cross-ply laminates [0 (sub 2) divided by 90 (sub 2),]s; angled-ply laminates [plus 45 (sub 2) divided by -45 (sub 2), ]s; doubled-edge-notched [0] (sub 8), laminates; and central-hole laminates. Results correlated well with the experimental data. This work was performed as a validation and benchmarking exercise of the FEAMAC/CARES program. FEAMAC/CARES simulates stochastic-based discrete-event progressive damage of ceramic matrix composite and polymer matrix composite material structures. It couples three software programs: (1) the Micromechanics Analysis Code with Generalized Method of Cells (MAC/GMC), (2) the Ceramics Analysis and Reliability Evaluation of Structures Life Prediction Program (CARES/Life), and (3) the Abaqus finite element analysis program. MAC/GMC contributes multiscale modeling capabilities and micromechanics relations to determine stresses and deformations at the microscale of the composite material repeating-unit-cell (RUC). CARES/Life contributes statistical multiaxial failure criteria that can be applied to the individual brittle-material constituents of the RUC, and Abaqus is used to model the overall composite structure. For each FEAMAC/CARES simulation trial, the stochastic nature of brittle material strength results in random, discrete damage events that incrementally progress until ultimate structural failure.

The effects of an 8-week multicomponent inpatient treatment program on body composition and anaerobic fitness in overweight and obese children and adolescents

Directory of Open Access Journals (Sweden)

Karner-Rezek K

2013-03-01

Full Text Available Klaus Karner-Rezek,1 Beat Knechtle,2,3 Matthias Fenzl,4 Christian Schlegel,4 Manuela Konrad,5 Thomas Rosemann2 1Private University of the Principality of Liechtenstein, Triesen, Principality of Liechtenstein, 2Institute of General Practice and for Health Services Research, University of Zurich, Zurich, Switzerland; 3Gesundheitszentrum St Gallen, St Gallen, Switzerland; 4Swiss Olympic Medical Center, Medizinisches Zentrum Bad Ragaz, Switzerland; 5University of Applied Sciences JOANNEUM, Bad Gleichenberg, Austria Background: High intensity exercise is considered as an effective means for reducing body fat. The aims of the present study were to investigate (1 whether body mass would be lost and body composition would change and (2 whether variables of anaerobic fitness prior to the intervention period would be related to loss of body mass and changes in body composition in overweight and obese children and adolescents. Methods: A total of 28 children and adolescents (19 boys, 9 girls attended an 8-week multicomponent inpatient program. Caloric intake was based on the subject's weight and a daily energy deficit of ~500 kcal was targeted. At the beginning and at the end of the program, variables of anaerobic fitness were assessed using Wingate tests. Body composition was measured before and after the program using dual-energy X-ray absorptiometry. Results: Body mass decreased by 11.4% ± 1.6% in boys and by 11.0% ± 2.8% in girls (P < 0.001. Fat mass decreased by 23.8% ± 6.1% in boys and by 21.5% ± 5.2% in girls (P < 0.001. The decrease in fat mass was associated with the decrease in body mass in boys (r = 0.54, P = 0.017 but not in girls (P > 0.05. The decrease in body mass and the decrease in fat mass were neither associated with overall energy expenditure nor with the energy deficit in both genders (P > 0.05. Mean power in W/kg increased in the Wingate tests by 95.4% ± 109.1% in boys and by 100.0% ± 119.9% in girls (P < 0.001. Conclusions

Developmental assessment of the Fort St. Vrain version of the Composite HTGR Analysis Program (CHAP-2)

International Nuclear Information System (INIS)

Stroh, K.R.

1980-01-01

The Composite HTGR Analysis Program (CHAP) consists of a model-independent systems analysis mainframe named LASAN and model-dependent linked code modules, each representing a component, subsystem, or phenomenon of an HTGR plant. The Fort St. Vrain (FSV) version (CHAP-2) includes 21 coded modules that model the neutron kinetics and thermal response of the core; the thermal-hydraulics of the reactor primary coolant system, secondary steam supply system, and balance-of-plant; the actions of the control system and plant protection system; the response of the reactor building; and the relative hazard resulting from fuel particle failure. FSV steady-state and transient plant data are being used to partially verify the component modeling and dynamic smulation techniques used to predict plant response to postulated accident sequences

Comment to: The effects of an 8-week multicomponent inpatient treatment program on body composition and anaerobic fitness in overweight and obese children and adolescents

Directory of Open Access Journals (Sweden)

Radtke T

2014-03-01

Full Text Available Thomas Radtke,1 Bruno H Knöpfli,2 Johannes H Wildhaber,3 Jürg Hammer4 1Division of Cardiovascular Prevention, Rehabilitation and Sports Medicine, Swiss Cardiovascular Center, Inselspital, University Hospital and University of Bern, Bern, 2Kinder und Jugendmedizin, Zurich, 3Department of Pediatrics, Hospital Fribourg, Fribourg, 4Division of Intensive Care and Pulmonology, University Children's Hospital Basel, Basel, SwitzerlandWe note with surprise a recent paper entitled "The effects of an 8-week multicomponent inpatient treatment program on body composition and anaerobic fitness in overweight and obese children and adolescents" by Karner-Rezek et al1 published in the International Journal of General Medicine concerning the effects of an 8-week multicomponent inpatient treatment program on body composition and anaerobic fitness in overweight and obese children and adolescents. We would like to take this opportunity to comment on the study findings and, in particular, address the methodological inconsistencies and ambiguities in this study.View original paper by Karner-Rezek and colleagues.

Anthropometry and Body Composition of Preterm Neonates in the Light of Metabolic Programming.

Science.gov (United States)

Parlapani, Elisavet; Agakidis, Charalampos; Karagiozoglou-Lampoudi, Thomais

2018-01-01

The improved survival of preterm infants has led to increased interest regarding their health as adults. In the context of metabolic programming, the connection between perinatal and early postnatal nutrition and growth with health in later life has brought to the fore the role of catch-up growth during the first months of preterm infants' lives and its association with body fat and obesity in childhood or puberty. A state-of-the art review was conducted in order to assess the way catch-up is evaluated, in terms of timing and rate. Adequate growth is of major importance for neurodevelopment; however, it may compete with adiposity or metabolic health. Studies based on body composition assessment have given conflicting results as regards the effect of early versus late and rapid versus slow catch-up growth on later health, mainly attributed to the lack of established criteria and definitions. Given that adequate early nutrition is crucial for the neurodevelopment of preterm infants, further studies are needed on the role of catch-up growth in long-term outcome, using generally accepted qualitative and quantitative criteria.

Modeling of combustion products composition of hydrogen-containing fuels

International Nuclear Information System (INIS)

Assad, M.S.

2010-01-01

Due to the usage of entropy maximum principal the algorithm and the program of chemical equilibrium calculation concerning hydrogen--containing fuels are devised. The program enables to estimate the composition of combustion products generated in the conditions similar to combustion conditions in heat engines. The program also enables to reveal the way hydrogen fraction in the conditional composition of the hydrocarbon-hydrogen-air mixture influences the harmful components content. It is proven that molecular hydrogen in the mixture is conductive to the decrease of CO, CO 2 and CH x concentration. NO outlet increases due to higher combustion temperature and N, O, OH concentrations in burnt gases. (authors)

Cooperative program for design, fabrication, and testing of graphite/epoxy composite helicopter shafting

Science.gov (United States)

Wright, C. C.; Baker, D. J.; Corvelli, N.; Thurston, L.; Clary, R.; Illg, W.

1971-01-01

The fabrication of UH-1 helicopter tail rotor drive shafts from graphite/epoxy composite materials is discussed. Procedures for eliminating wrinkles caused by lack of precure compaction are described. The development of the adhesive bond between aluminum end couplings and the composite tube is analyzed. Performance tests to validate the superiority of the composite materials are reported.

Eimeria Oocyst Concentrations and Species Composition in Litter from Commercial Broiler Farms During Anticoccidial Drug or Live Eimeria Oocyst Vaccine Control Programs.

Science.gov (United States)

Jenkins, Mark C; Parker, Carolyn; Ritter, Donald

2017-06-01

The purpose of this study was to determine if Eimeria oocyst concentrations and species composition in commercial broiler house litter changed during different cycles of anticoccidial drug (ACD) or live Eimeria oocyst vaccine (VAC) control programs and if there was a correlation between Eimeria oocyst levels and broiler performance. Litter samples were collected from a total of 15 different broiler farms encompassing a total of 45 individual houses during at least one complete grow-out cycle over a 21-mo period. Of these 15 broiler farms, three were followed for the entire 21-mo period spanning three ACD and four VAC cycles. Samples were collected at 2, 4, and 7-8 wk of grow-out corresponding to starter, grower, and withdraw periods of the ACD cycle. On a number of occasions, litter samples were obtained just prior to chick placement. Eimeria oocysts were isolated from all samples, counted by microscopy, and extracted for DNA to identify Eimeria species by ITS1 PCR. In general, Eimeria oocyst concentration in litter reached peak levels at 2-4 wk of grow-out regardless of coccidiosis control measure being used. However, peak oocyst numbers were sometimes delayed until 7-8 wk, indicating some level of Eimeria spp. drug resistance or incomplete vaccine coverage. Eimeria maxima , Eimeria acervulina , Eimeria praecox, and Eimeria tenella were generally present in all samples, and no difference in the species composition was noted between houses on a particular farm. While Eimeria species composition was similar among houses, Eimeria spp. oocyst levels exhibited sporadic peaks in one house of a given location's houses. Of particular interest was the observed correlation between E. maxima oocyst abundance and chick mortality. However, no correlation was observed in E. maxima oocyst levels, and the performance parameters adjusted feed conversion ratio and average daily weight gain. This study showed that understanding the dynamics of Eimeria spp. oocyst levels and species

Adjusting shape-memory properties of amorphous polyether urethanes and radio-opaque composites thereof by variation of physical parameters during programming

International Nuclear Information System (INIS)

Cui, J; Kratz, K; Lendlein, A

2010-01-01

Various composites have been prepared to improve the mechanical properties of shape-memory polymers (SMPs) or to incorporate new functionalities (e.g. magneto-sensitivity) in polymer matrices. In this paper, we systematically investigated the influence of the programming temperature T prog and the applied strain ε m as parameters of the shape-memory creation procedure (SMCP) on the shape-memory properties of an amorphous polyether urethane and radio-opaque composites thereof. Recovery under stress-free conditions was quantified by the shape recovery rate R r and the switching temperature T sw , while the maximum recovery stress σ max was determined at the characteristic temperature T σ,max under constant strain conditions. Excellent shape-memory properties were achieved in all experiments with R r values in between 80 and 98%. σ max could be tailored from 0.4 to 3.7 MPa. T sw and T σ,max could be systematically adjusted from 33 to 71 °C by variation of T prog for each investigated sample. The investigated radio-opaque shape-memory composites will form the material basis for mechanically active scaffolds, which could serve as an intelligent substitute for the extracellular matrix to study the influence of mechanical stimulation of tissue development

Boron carbide-carbon composites and composites for cryogenic applications

International Nuclear Information System (INIS)

Sheinberg, H.

1979-01-01

Because of its neutronic properties, high hardness, and high melting temperature, boron carbide (B 4 C) is widely used at the Los Alamos Scientific Laboratory. However because of its hardness and mode of manufacture, it is expensive to machine finish to tight dimensional specifictions. For some neutronic applications, a density considerably below the theoretical 2.52 Mg/m 3 was acceptable, and this relaxation in density specification permitted addition of carbon as a second phase to reduce machining costs. We conducted an experimental program to prepare 50.8-mm-diam by 34.8-mm-thick cylinders of B 4 C and B 4 C-C composites with concentrations of carbon varying from 5.5 to 30 volume percent. Additionally we used three forms of carbon, natural flake graphite, synthetic graphite flour, and a fine furnace black as the source of the second phase. We determined the sound velocity, compressive strength, coefficient of thermal expansion, electrical resistivity, and microstructure as functions of composition. Additionally, an enriched boron ( 10 B)-carbon composite was studied as an alternate material

HYDRAULIC CONCRETE COMPOSITION AND PROPERTIES CONTROL SYSTEM

Directory of Open Access Journals (Sweden)

O. M. Pshinko

2015-08-01

Full Text Available Purpose. Scientific work aims at the development and testing of information system to meet the challenges of concrete composition design and control (for railway structures and buildings based on the physico-analytical method algorithm for hydraulic concrete composition calculation. Methodology. The proposed algorithm of hydraulic concrete composition calculation is based on the physicochemical mechanics and in particular on the rheology of elastic–viscous–plastic bodies. The system of canonical equations consists of the equations for concrete strength, absolute volume, concrete mix consistency as well as the equation for optimal concrete saturation with aggregates while minimizing cement content. The joint solution of these four equations related to composition allows determining for the materials the concrete composition of required strength, concrete workability with minimum cement content. The procedure for calculation of hydraulic concrete composition according to the physico-analytical method consists of two parts: 1 physical, which is laboratory testing of concrete mix components in different concrete compositions; 2 analytical, which represents the calculation algorithm for concrete compositions equivalent in concrete strength and workability that comply with the specific conditions of concrete placing. Findings. To solve the problem of designing the concrete composition with the desired properties for railway structures and buildings it was proposed to use the information technology in the form of a developed computer program whose algorithm includes the physico-analytical method for hydraulic concrete composition determination. Originality. The developed concrete composition design method takes into account the basic properties of raw materials, concrete mix and concrete, which are pre-determined. The distinctive feature of physico-analytical method is obtaining of a set of equivalent compositions with a certain concrete mix

Adaptive, Active and Multifunctional Composite and Hybrid Materials Program: Composite and Hybrid Materials ERA

Science.gov (United States)

2014-04-01

590 . SMASIS2011-4934. L. D. Peel, J. Baur, D. Phillips, and A. McClung, “The Effect of Scaling on the Performance of Elastomer Composite Actuators...fragility of the fibers it was also not possible to extract some of them from their adhesive paper mountings without breakage. For Raman ... Raman spectroscopy and microscopy (SEM), the nanocomposites were evaluated for their thermal analytical properties using TGA. Electrical

Compositional Safety Analysis using Barrier Certificates

DEFF Research Database (Denmark)

Sloth, Christoffer; Pappas, George J.; Wisniewski, Rafael

2012-01-01

This paper proposes a compositional method for verifying the safety of a dynamical system, given as an interconnection of subsystems. The safety verification is conducted by the use of the barrier certificate method; hence, the contribution of this paper is to show how to obtain compositional...... conditions for safety verification. We show how to formulate the verification problem, as a composition of coupled subproblems, each given for one subsystem. Furthermore, we show how to find the compositional barrier certificates via linear and sum of squares programming problems. The proposed method makes...... it possible to verify the safety of higher dimensional systems, than the method for centrally computed barrier certificates. This is demonstrated by verifying the safety of an emergency shutdown of a wind turbine....

Second generation PMR polyimide/fiber composites

Science.gov (United States)

Cavano, P. J.

1979-01-01

A second generation polymerization monomeric reactants (PMR) polyimdes matrix system (PMR 2) was characterized in both neat resin and composite form with two different graphite fiber reinforcements. Three different formulated molecular weight levels of laboratory prepared PMR 2 were examined, in addition to a purchased experimental fully formulated PMR 2 precurser solution. Isothermal aging of graphite fibers, neat resin samples and composite specimens in air at 316 C were investigated. Humidity exposures at 65 C and 97 percent relative humidity were conducted for both neat resin and composites for eight day periods. Anaerobic char of neat resin and fire testing of composites were conducted with PMR 15, PMR 2, and an epoxy system. Composites were fire tested on a burner rig developed for this program. Results indicate that neat PMR 2 resins exhibit excellent isothermal resistance and that PMR 2 composite properties appear to be influenced by the thermo-oxidative stability of the reinforcing fiber.

Composition at Washington State University: Building a Multimodal Bricolage

Science.gov (United States)

Ericsson, Patricia; Hunter, Leeann Downing; Macklin, Tialitha Michelle; Edwards, Elizabeth Sue

2016-01-01

Multimodal pedagogy is increasingly accepted among composition scholars. However, putting such pedagogy into practice presents significant challenges. In this profile of Washington State University's first-year composition program, we suggest a multi-vocal and multi-theoretical approach to addressing the challenges of multimodal pedagogy. Patricia…

Critical joints in large composite aircraft structure

Science.gov (United States)

Nelson, W. D.; Bunin, B. L.; Hart-Smith, L. J.

1983-01-01

A program was conducted at Douglas Aircraft Company to develop the technology for critical structural joints of composite wing structure that meets design requirements for a 1990 commercial transport aircraft. The prime objective of the program was to demonstrate the ability to reliably predict the strength of large bolted composite joints. Ancillary testing of 180 specimens generated data on strength and load-deflection characteristics which provided input to the joint analysis. Load-sharing between fasteners in multirow bolted joints was computed by the nonlinear analysis program A4EJ. This program was used to predict strengths of 20 additional large subcomponents representing strips from a wing root chordwise splice. In most cases, the predictions were accurate to within a few percent of the test results. In some cases, the observed mode of failure was different than anticipated. The highlight of the subcomponent testing was the consistent ability to achieve gross-section failure strains close to 0.005. That represents a considerable improvement over the state of the art.

Database for waste glass composition and properties

International Nuclear Information System (INIS)

Peters, R.D.; Chapman, C.C.; Mendel, J.E.; Williams, C.G.

1993-09-01

A database of waste glass composition and properties, called PNL Waste Glass Database, has been developed. The source of data is published literature and files from projects funded by the US Department of Energy. The glass data have been organized into categories and corresponding data files have been prepared. These categories are glass chemical composition, thermal properties, leaching data, waste composition, glass radionuclide composition and crystallinity data. The data files are compatible with commercial database software. Glass compositions are linked to properties across the various files using a unique glass code. Programs have been written in database software language to permit searches and retrievals of data. The database provides easy access to the vast quantities of glass compositions and properties that have been studied. It will be a tool for researchers and others investigating vitrification and glass waste forms

Composite Materials: An Educational Need.

Science.gov (United States)

Saliba, Tony E.; Snide, James A.

1990-01-01

Described is the need to incorporate the concepts and applications of advanced composite materials into existing chemical engineering programs. Discussed are the justification for, and implementation of topics including transport phenomena, kinetics and reactor design, unit operations, and product and process design. (CW)

A model for the design and programming of multi-cores

NARCIS (Netherlands)

Jesshope, C.; Grandinetti, L.

2008-01-01

This paper describes a machine/programming model for the era of multi-core chips. It is derived from the sequential model but replaces sequential composition with concurrent composition at all levels in the program except at the level where the compiler is able to make deterministic decisions on

Medicare Program; Prospective Payment System and Consolidated Billing for Skilled Nursing Facilities for FY 2018, SNF Value-Based Purchasing Program, SNF Quality Reporting Program, Survey Team Composition, and Correction of the Performance Period for the NHSN HCP Influenza Vaccination Immunization Reporting

Science.gov (United States)

2017-08-04

This final rule updates the payment rates used under the prospective payment system (PPS) for skilled nursing facilities (SNFs) for fiscal year (FY) 2018. It also revises and rebases the market basket index by updating the base year from 2010 to 2014, and by adding a new cost category for Installation, Maintenance, and Repair Services. The rule also finalizes revisions to the SNF Quality Reporting Program (QRP), including measure and standardized resident assessment data policies and policies related to public display. In addition, it finalizes policies for the Skilled Nursing Facility Value-Based Purchasing Program that will affect Medicare payment to SNFs beginning in FY 2019. The final rule also clarifies the regulatory requirements for team composition for surveys conducted for investigating a complaint and aligns regulatory provisions for investigation of complaints with the statutory requirements. The final rule also finalizes the performance period for the National Healthcare Safety Network (NHSN) Healthcare Personnel (HCP) Influenza Vaccination Reporting Measure included in the End-Stage Renal Disease (ESRD) Quality Incentive Program (QIP) for Payment Year 2020.

Durability of aircraft composite materials

Science.gov (United States)

Dextern, H. B.

1982-01-01

Confidence in the long term durability of advanced composites is developed through a series of flight service programs. Service experience is obtained by installing secondary and primary composite components on commercial and military transport aircraft and helicopters. Included are spoilers, rudders, elevators, ailerons, fairings and wing boxes on transport aircraft and doors, fairings, tail rotors, vertical fins, and horizontal stabilizers on helicopters. Materials included in the evaluation are boron/epoxy, Kevlar/epoxy, graphite/epoxy and boron/aluminum. Inspection, maintenance, and repair results for the components in service are reported. The effects of long term exposure to laboratory, flight, and outdoor environmental conditions are reported for various composite materials. Included are effects of moisture absorption, ultraviolet radiation, and aircraft fuels and fluids.

7 CFR 3400.11 - Composition of peer review groups.

Science.gov (United States)

2010-01-01

... 7 Agriculture 15 2010-01-01 2010-01-01 false Composition of peer review groups. 3400.11 Section..., EDUCATION, AND EXTENSION SERVICE, DEPARTMENT OF AGRICULTURE SPECIAL RESEARCH GRANTS PROGRAM Scientific Peer Review of Research Grant Applications § 3400.11 Composition of peer review groups. (a) Peer review group...

Material Programming

DEFF Research Database (Denmark)

Vallgårda, Anna; Boer, Laurens; Tsaknaki, Vasiliki

2017-01-01

. Consequently we ask what the practice of programming and giving form to such materials would be like? How would we be able to familiarize ourselves with the dynamics of these materials and their different combinations of cause and effect? Which tools would we need and what would they look like? Will we program......, and color, but additionally being capable of sensing, actuating, and computing. Indeed, computers will not be things in and by themselves, but embedded into the materials that make up our surroundings. This also means that the way we interact with computers and the way we program them, will change...... these computational composites through external computers and then transfer the code them, or will the programming happen closer to the materials? In this feature we outline a new research program that floats between imagined futures and the development of a material programming practice....

Raters’ Perception and Expertise in Evaluating Second Language Compositions

Directory of Open Access Journals (Sweden)

Houman Bijani

2010-11-01

Full Text Available The consideration of rater training is very important in construct validation of a writing test because it is through training that raters are adapted to the use of students’ writing ability instead of their own criteria for assessing compositions (Charney, 1984. However, although training has been discussed in the literature of writing assessment, there is little research regarding raters’ perceptions and understandings of the training program. Although a few studies have looked at the differences between trained and untrained raters in writing assessment (Cumming, 1990; Huot, 1990, few studies have used a pre-and post-training design. The purpose of this study is to investigate the effectiveness of the training program on experienced and inexperienced raters with regard to a pre-and post- training design. Twelve EFL raters scored 45 pre-rated benchmark essay compositions by an authorized IELTS trainer. These essay compositions were scored before, during and after the training program. The results regarding the comparison across raters showed that inexperienced raters had wider range of inconsistency before training but they became more consistent than experienced raters after training.

A FRAMEWORK FOR PERFORMANCE EVALUATION AND MONITORING OF PUBLIC HEALTH PROGRAM USING COMPOSITE PERFORMANCE INDEX

Directory of Open Access Journals (Sweden)

Susanta Kumar Gauri

2017-12-01

Full Text Available A public health program (PHP taken up by the government of a country refers to all organized measures to prevent disease and promote health among the population, by providing different planned cares/services to the people. Usually, the target population for different PHP are different. The basic requirement for success of a PHP is to ensure that all the planned cares/services are reached to each member of the target population. Therefore, the important performance measures for a PHP are the implementation status of all the planned cares/services under the PHP. However, management and monitoring of a PHP become quite difficult by interpreting separately the information contained in a large number of performance measures. Therefore, usually a metric, called composite performance index (CPI, is evaluated to understand the overall performance of a PHP. However, due a scaling operation involved in the CPI computation procedure, the CPI value does not reveal the true overall implementation status of a PHP and consequently, it is effective for management of a PHP. This paper presents a new approach for CPI computation, in which scaling/normalization of the performance variables is not required and therefore, it can be used for monitoring the true overall implementation status of a PHP in a region. A systematic approach for monitoring a PHP using the CPI values is proposed and applied for monitoring the maternal and child healthcare (MCH program. The results are found effective towards continuous improvement of implementation status.

Effects of a mini-trampoline rebounding exercise program on functional parameters, body composition and quality of life in overweight women.

Science.gov (United States)

Cugusi, Lucia; Manca, Andrea; Serpe, Roberto; Romita, Giovanni; Bergamin, Marco; Cadeddu, Christian; Solla, Paolo; Mercuro, Giuseppe

2018-03-01

Mini-trampoline rebounding exercise (MRE) is becoming a very popular form of fitness training. Despite awareness of this activity worldwide, a limited number of studies have systematically investigated the health effects correlated with MRE training. The aim of our study was to evaluate manifold health outcomes after 12 weeks of an MRE program in a group of overweight Italian women. Eighteen overweight women (age 38.05±10.5 years, BMI: 27.6±2.1 kg/m2) were enrolled in this study. Functional profile, strength, body composition, quality of life and pain intensity were assessed at baseline and after 12 weeks of MRE. Significant improvements were observed in the measurements of anthropometric profile and body composition (circumferences, fat mass, lean and muscular mass). Both a significant decrease in systolic and diastolic blood pressure values (from 128/80.5 to 123/71 mmHg, P<0.05) and an improvement in lipid and glucose profiles were observed. At maximal exercise testing, an increase in work capacity (from 104 to 123 watts, P=0.003) and VO2max (from 15.4 to 16.9 mL/kg/min, P=0.04) was found. SF-36 showed positive changes in four of the eight items as well as in the Mental Component Summary. With regard to the Brief Pain Inventory-SF, a decrease in both pain severity and the pain interference score was detected. MRE appears feasible to ensure positive effects on overall health and can be proposed to populations that could greatly benefit from training programs, such as overweight women.

7 CFR 3415.11 - Composition of peer review groups.

Science.gov (United States)

2010-01-01

... 7 Agriculture 15 2010-01-01 2010-01-01 false Composition of peer review groups. 3415.11 Section... PROGRAM Scientific Peer Review of Research Grant Applications § 3415.11 Composition of peer review groups. (a) Peer review group members and ad hoc reviewers will be selected based upon their training and...

7 CFR 3411.11 - Composition of peer review groups.

Science.gov (United States)

2010-01-01

... 7 Agriculture 15 2010-01-01 2010-01-01 false Composition of peer review groups. 3411.11 Section... PROGRAM Scientific Peer Review of Research Grant Applications § 3411.11 Composition of peer review groups. (a) Peer review group members and ad hoc reviewers will be selected based upon their training and...

USDA's National Food and Nutrient Analysis Program (NFNAP) produces high-quality data for USDA food composition databases: Two decades of collaboration.

Science.gov (United States)

Haytowitz, David B; Pehrsson, Pamela R

2018-01-01

For nearly 20years, the National Food and Nutrient Analysis Program (NFNAP) has expanded and improved the quantity and quality of data in US Department of Agriculture's (USDA) food composition databases (FCDB) through the collection and analysis of nationally representative food samples. NFNAP employs statistically valid sampling plans, the Key Foods approach to identify and prioritize foods and nutrients, comprehensive quality control protocols, and analytical oversight to generate new and updated analytical data for food components. NFNAP has allowed the Nutrient Data Laboratory to keep up with the dynamic US food supply and emerging scientific research. Recently generated results for nationally representative food samples show marked changes compared to previous database values for selected nutrients. Monitoring changes in the composition of foods is critical in keeping FCDB up-to-date, so that they remain a vital tool in assessing the nutrient intake of national populations, as well as for providing dietary advice. Published by Elsevier Ltd.

A Semantics for Modular General Logic Programs

NARCIS (Netherlands)

Etalle, Sandro

1998-01-01

Modular programs are built as a combination of separate modules, which may be developed and verified separately. Therefore, in order to reason over such programs, compositionality plays a crucial role: the semantics of the whole program must be obtainable as a simple function from the semantics of

A semantics for modular general logic programs

NARCIS (Netherlands)

Etalle, S.

1998-01-01

Modular programs are built as a combination of separate modules, which may be developed and verified separately. Therefore, in order to reason over such programs, compositionality plays a crucial role: the semantics of the whole program must be obtainable as a simple function from the semantics of

Feature-Oriented Programming with Object Algebras

NARCIS (Netherlands)

B.C.d.S. Oliveira (Bruno); T. van der Storm (Tijs); A. Loh; W.R. Cook

2013-01-01

htmlabstractObject algebras are a new programming technique that enables a simple solution to basic extensibility and modularity issues in programming languages. While object algebras excel at defining modular features, the composition mechanisms for object algebras (and features) are still

Fetal Programming of Body Composition, Obesity, and Metabolic Function: The Role of Intrauterine Stress and Stress Biology

Directory of Open Access Journals (Sweden)

Sonja Entringer

2012-01-01

Full Text Available Epidemiological, clinical, physiological, cellular, and molecular evidence suggests that the origins of obesity and metabolic dysfunction can be traced back to intrauterine life and supports an important role for maternal nutrition prior to and during gestation in fetal programming. The elucidation of underlying mechanisms is an area of interest and intense investigation. In this perspectives paper we propose that in addition to maternal nutrition-related processes it may be important to concurrently consider the potential role of intrauterine stress and stress biology. We frame our arguments in the larger context of an evolutionary-developmental perspective that supports roles for both nutrition and stress as key environmental conditions driving natural selection and developmental plasticity. We suggest that intrauterine stress exposure may interact with the nutritional milieu, and that stress biology may represent an underlying mechanism mediating the effects of diverse intrauterine perturbations, including but not limited to maternal nutritional insults (undernutrition and overnutrition, on brain and peripheral targets of programming of body composition, energy balance homeostasis, and metabolic function. We discuss putative maternal-placental-fetal endocrine and immune/inflammatory candidate mechanisms that may underlie the long-term effects of intrauterine stress. We conclude with a commentary of the implications for future research and clinical practice.

Safety of GM crops: compositional analysis.

Science.gov (United States)

Brune, Philip D; Culler, Angela Hendrickson; Ridley, William P; Walker, Kate

2013-09-04

The compositional analysis of genetically modified (GM) crops has continued to be an important part of the overall evaluation in the safety assessment program for these materials. The variety and complexity of genetically engineered traits and modes of action that will be used in GM crops in the near future, as well as our expanded knowledge of compositional variability and factors that can affect composition, raise questions about compositional analysis and how it should be applied to evaluate the safety of traits. The International Life Sciences Institute (ILSI), a nonprofit foundation whose mission is to provide science that improves public health and well-being by fostering collaboration among experts from academia, government, and industry, convened a workshop in September 2012 to examine these and related questions, and a series of papers has been assembled to describe the outcomes of that meeting.

Optimization of medium composition for apple rootstocks

African Journals Online (AJOL)

User

2011-05-02

May 2, 2011 ... Key words: Apple rootstocks, medium composition, multiplication rate, plant growth regulators (PGRs). ... be extrapolated with the same success for another .... Analysis System (SAS) software program (SAS Institute Inc. 1999).

Advanced Industrial Materials Program. Annual progress report, FY 1993

Energy Technology Data Exchange (ETDEWEB)

Stooksbury, F. [comp.

1994-06-01

Mission of the AIM program is to commercialize new/improved materials and materials processing methods that will improve energy efficiency, productivity, and competitiveness. Program investigators in the DOE national laboratories are working with about 100 companies, including 15 partners in CRDAs. Work is being done on intermetallic alloys, ceramic composites, metal composites, polymers, engineered porous materials, and surface modification. The program supports other efforts in the Office of Industrial Technologies to assist the energy-consuming process industries. The aim of the AIM program is to bring materials from basic research to industrial application to strengthen the competitive position of US industry and save energy.

Thermal Protective Coating for High Temperature Polymer Composites

Science.gov (United States)

Barron, Andrew R.

1999-01-01

The central theme of this research is the application of carboxylate-alumoxane nanoparticles as precursors to thermally protective coatings for high temperature polymer composites. In addition, we will investigate the application of carboxylate-alumoxane nanoparticle as a component to polymer composites. The objective of this research was the high temperature protection of polymer composites via novel chemistry. The significance of this research is the development of a low cost and highly flexible synthetic methodology, with a compatible processing technique, for the fabrication of high temperature polymer composites. We proposed to accomplish this broad goal through the use of a class of ceramic precursor material, alumoxanes. Alumoxanes are nano-particles with a boehmite-like structure and an organic periphery. The technical goals of this program are to prepare and evaluate water soluble carboxylate-alumoxane for the preparation of ceramic coatings on polymer substrates. Our proposed approach is attractive since proof of concept has been demonstrated under the NRA 96-LeRC-1 Technology for Advanced High Temperature Gas Turbine Engines, HITEMP Program. For example, carbon and Kevlar(tm) fibers and matting have been successfully coated with ceramic thermally protective layers.

The composite sequential clustering technique for analysis of multispectral scanner data

Science.gov (United States)

Su, M. Y.

1972-01-01

The clustering technique consists of two parts: (1) a sequential statistical clustering which is essentially a sequential variance analysis, and (2) a generalized K-means clustering. In this composite clustering technique, the output of (1) is a set of initial clusters which are input to (2) for further improvement by an iterative scheme. This unsupervised composite technique was employed for automatic classification of two sets of remote multispectral earth resource observations. The classification accuracy by the unsupervised technique is found to be comparable to that by traditional supervised maximum likelihood classification techniques. The mathematical algorithms for the composite sequential clustering program and a detailed computer program description with job setup are given.

Nutrient Requirements, Body Composition, and Health of Military Women

National Research Council Canada - National Science Library

Costello, Rebecca

1998-01-01

.... As pan of the Defense Women's Health Research Program, a new report from the Committee on Body Composition, Nutrition, and Health of Military Women of the Institute of the Institute of Medicine examines issues of body composition, fitness, and appearance standards and their impact on the health, nutritional status, and performance of active-duty women.

How to use composite indicator and linear programming model for determine sustainable tourism.

Science.gov (United States)

Ziaabadi, Maryam; Malakootian, Mohammad; Zare Mehrjerdi, Mohammad Reza; Jalaee, Seied Abdolmajid; Mehrabi Boshrabadi, Hosein

2017-01-01

The tourism industry which is one of the most dynamic economic activities in today's world plays a significant role in the sustainable development. Therefore, in addition to paying attention to tourism, sustainable tourism must be taken into huge account; otherwise, the environment and its health will be damaged irreparably. To determine the level of sustainability in this study, indicators of sustainable tourism were first presented in three environmental health, economic and social aspects. Then, the levels of sustainable tourism and environmental sustainability were practically measured in different cities of Kerman Province using a composite indicator, a linear programming model, Delphi method and the questionnaire technique. Finally, the study cities (tourist attractions) were ranked. Result of this study showed that unfortunately the tourism opportunities were not used appropriately in these cities and tourist destinations, and that environmental aspect (health and environmental sustainability) had very bad situations compared to social and economic aspects. In other words, environmental health had the lowest levels of sustainability. The environment is a place for all human activities like tourism, social and economic issues; therefore, its stability and health is of great importance. Thus, it is necessary to pay more attention to sustainability of activities, management and environmental health in planning sustainable development in regional and national policy.

Composites for Exploration Upper Stage

Science.gov (United States)

Fikes, J. C.; Jackson, J. R.; Richardson, S. W.; Thomas, A. D.; Mann, T. O.; Miller, S. G.

2016-01-01

The Composites for Exploration Upper Stage (CEUS) was a 3-year, level III project within the Technology Demonstration Missions program of the NASA Space Technology Mission Directorate. Studies have shown that composites provide important programmatic enhancements, including reduced weight to increase capability and accelerated expansion of exploration and science mission objectives. The CEUS project was focused on technologies that best advanced innovation, infusion, and broad applications for the inclusion of composites on future large human-rated launch vehicles and spacecraft. The benefits included near- and far-term opportunities for infusion (NASA, industry/commercial, Department of Defense), demonstrated critical technologies and technically implementable evolvable innovations, and sustained Agency experience. The initial scope of the project was to advance technologies for large composite structures applicable to the Space Launch System (SLS) Exploration Upper Stage (EUS) by focusing on the affordability and technical performance of the EUS forward and aft skirts. The project was tasked to develop and demonstrate critical composite technologies with a focus on full-scale materials, design, manufacturing, and test using NASA in-house capabilities. This would have demonstrated a major advancement in confidence and matured the large-scale composite technology to a Technology Readiness Level 6. This project would, therefore, have bridged the gap for providing composite application to SLS upgrades, enabling future exploration missions.

Aspect-Oriented Programming Using Composition Filters, in Object-Oriented Technology

NARCIS (Netherlands)

Aksit, Mehmet; Demeyer, S.; Bosch, H.G.P.; Tekinerdogan, B.

Software engineers may experience problems in modeling certain aspects while applying object-oriented techniques [4, 10, 11]. Composition-Filters are capable of expressing various different kinds of aspects in a uniform manner. These aspects are, for example, inheritance and delegation [1] and

MRI: Modular reasoning about interference in incremental programming

OpenAIRE

Oliveira, Bruno C. D. S; Schrijvers, Tom; Cook, William R

2012-01-01

Incremental Programming (IP) is a programming style in which new program components are defined as increments of other components. Examples of IP mechanisms include: Object-oriented programming (OOP) inheritance, aspect-oriented programming (AOP) advice and feature-oriented programming (FOP). A characteristic of IP mechanisms is that, while individual components can be independently defined, the composition of components makes those components become tightly coupled, sh...

SOILSOLN: A Program for Teaching Equilibria Modeling of Soil Solution Composition.

Science.gov (United States)

Wolt, Jeffrey D.

1989-01-01

Presents a computer program for use in teaching ion speciation in soil solutions. Provides information on the structure of the program, execution, and software specifications. The program estimates concentrations of ion pairs, hydrolytic species, metal-organic complexes, and free ions in solutions. (Author/RT)

Composite flywheel development completion report, May 1--September 30, 1976

Energy Technology Data Exchange (ETDEWEB)

Huddleston, R. L.; Kelly, J. J.; Knight, C. E.

1977-05-01

The program to design, fabricate, and performance test a prototype, vehicular-sized, composite flywheel is described. The overall program scope encompasses development of both the flywheel and its containment; however, the FY 1976-1976T objective was directed toward development of the flywheel and testing it in existing facilities. The development effort was successful, leading to successful testing of a flywheel design which demonstrated an energy density performance of 10.1 Wh/lb during spin testing. The initial application selected for development of the composite flywheel was the heat engine/flywheel hybrid propulsion system for a vehicle. This application was selected by the ERDA Advanced Physical Methods Branch staff because of its high potential for conservation of petroleum fuel in both the near and far-term time frames. Other applications, such as utility load leveling, represent potential areas for significant energy savings but require more extensive development programs and funding resources. Successful development of a high-performance, composite, vehicular flywheel represents one step along the development path leading toward larger, higher-energy storage flywheel applications.

Development of Textile Reinforced Composites for Aircraft Structures

Science.gov (United States)

Dexter, H. Benson

1998-01-01

NASA has been a leader in development of composite materials for aircraft applications during the past 25 years. In the early 1980's NASA and others conducted research to improve damage tolerance of composite structures through the use of toughened resins but these resins were not cost-effective. The aircraft industry wanted affordable, robust structures that could withstand the rigors of flight service with minimal damage. The cost and damage tolerance barriers of conventional laminated composites led NASA to focus on new concepts in composites which would incorporate the automated manufacturing methods of the textiles industry and which would incorporate through-the-thickness reinforcements. The NASA Advanced Composites Technology (ACT) Program provided the resources to extensively investigate the application of textile processes to next generation aircraft wing and fuselage structures. This paper discusses advanced textile material forms that have been developed, innovative machine concepts and key technology advancements required for future application of textile reinforced composites in commercial transport aircraft. Multiaxial warp knitting, triaxial braiding and through-the-thickness stitching are the three textile processes that have surfaced as the most promising for further development. Textile reinforced composite structural elements that have been developed in the NASA ACT Program are discussed. Included are braided fuselage frames and window-belt reinforcements, woven/stitched lower fuselage side panels, stitched multiaxial warp knit wing skins, and braided wing stiffeners. In addition, low-cost processing concepts such as resin transfer molding (RTM), resin film infusion (RFI), and vacuum-assisted resin transfer molding (VARTM) are discussed. Process modeling concepts to predict resin flow and cure in textile preforms are also discussed.

Behaviour of steel-concrete composite beams using bolts as shear connectors

Science.gov (United States)

Tran, Minh-Tung; Nguyen Van Do, Vuong; Nguyen, Tuan-Anh

2018-04-01

The paper presents an experimental program on the application of bolts as shear connectors for steel-composite beams. Four steel- concrete composite beams and a reference steel beam were made and tested. The aim of the testing program is to examine which forms of the steel bolts can be used effectively for steel-composite beams. The four types of the bolts include: Type 1 the bolt with the nut at the end; Type 2 the bolt bending at 900 hook; Type 3 the bolt without the nut at the end and Type 4 the bolt with the nut at the end but connected with the steel beam by hand welding in other to be connected with the steel beam by bolt connection as in the first three types. The test results showed that beside the traditional shear connectors like shear studs, angle type, channel type, bolts can be used effectively as the shear connectors in steel-composite beams and the application of bolts in Types 1 and 2 in the composite beams gave the better performance for the tested beam.

Flight service evaluation of an advanced composite empennage component on commercial transport aircraft. Phase 1: Engineering development

Science.gov (United States)

Ary, A.; Axtell, C.; Fogg, L.; Jackson, A.; James, A. M.; Mosesian, B.; Vanderwier, J.; Vanhamersveld, J.

1976-01-01

The empennage component selected for this program is the vertical fin box of the L-1011 aircraft. The box structure extends from the fuselage production joint to the tip rib and includes the front and rear spars. Various design options were evaluated to arrive at a configuration which would offer the highest potential for satisfying program objectives. The preferred configuration selected consists of a hat-stiffened cover with molded integrally stiffened spars, aluminum trussed composite ribs, and composite miniwich web ribs with integrally molded caps. Material screening tests were performed to select an advanced composite material system for the Advanced Composite Vertical Fin (ACFV) that would meet the program requirements from the standpoint of quality, reproducibility, and cost. Preliminary weight and cost analysis were made, targets established, and tracking plans developed. These include FAA certification, ancillary test program, quality control, and structural integrity control plans.

Critical joints in large composite primary aircraft structures. Volume 1: Technical summary

Science.gov (United States)

Bunin, Bruce L.

1985-01-01

A program was conducted at Douglas Aircraft Company to develop the technology for critical joints in composite wing structure that meets all the design requirements of a 1990 commercial transport aircraft. In fulfilling this objective, analytical procedures for joint design and analysis were developed during Phase 1 of the program. Tests were conducted at the element level to supply the empirical data required for methods development. Large composite multirow joints were tested to verify the selected design concepts and for correlation with analysis predictions. The Phase 2 program included additional tests to provide joint design and analysis data, and culminated with several technology demonstration tests of a major joint area representative of a commercial transport wing. The technology demonstration program of Phase 2 is discussed. The analysis methodology development, structural test program, and correlation between test results and analytical strength predictions are reviewed.

Bulk metallic glass matrix composite for good biocompatibility

International Nuclear Information System (INIS)

Hadjoub, F; Metiri, W; Doghmane, A; Hadjoub, Z

2012-01-01

Reinforcement volume fraction effects on acoustical parameters of Zr 41.2 Ti 13.8 Cu 12.5 Ni 10 Be 22.5 matrix composites reinforced by Mg, Ag and Cd metals have been studied via a simulation program based on acoustic microscopy technique. Moreover, acoustical parameters of human bone were compared to those of BMGs in both monolithic and reinforced case. It was found that elastic behavior of BMGs matrix composites in high reinforcement volume fraction is similar of that of human bone. This behavior leads to high biocompatibility and good transfer of stress between composite material and human system.

An Integrated, Layered-Spinel Composite Cathode for Energy Storage Applications

Science.gov (United States)

Hagh, Nader; Skandan, Ganesh

2012-01-01

At low operating temperatures, commercially available electrode materials for lithium-ion batteries do not fully meet the energy and power requirements for NASA fs exploration activities. The composite cathode under development is projected to provide the required energy and power densities at low temperatures and its usage will considerably reduce the overall volume and weight of the battery pack. The newly developed composite electrode material can provide superior electrochemical performance relative to a commercially available lithium cobalt system. One advantage of using a composite cathode is its higher energy density, which can lead to smaller and lighter battery packs. In the current program, different series of layered-spinel composite materials with at least two different systems in an integrated structure were synthesized, and the volumetric and gravimetric energy densities were evaluated. In an integrated network of a composite electrode, the effect of the combined structures is to enhance the capacity and power capabilities of the material to levels greater than what is possible in current state-of-the-art cathode systems. The main objective of the current program is to implement a novel cathode material that meets NASA fs low temperature energy density requirements. An important feature of the composite cathode is that it has at least two components (e.g., layered and spinel) that are structurally integrated. The layered material by itself is electrochemically inactive; however, upon structural integration with a spinel material, the layered material can be electrochemically activated, thereby delivering a large amount of energy with stable cycling. A key aspect of the innovation has been the development of a scalable process to produce submicronand micron-scale particles of these composite materials. An additional advantage of using such a composite electrode material is its low irreversible loss (.5%), which is primarily due to the unique activation

Characterization and manufacture of braided composites for large commercial aircraft structures

Science.gov (United States)

Fedro, Mark J.; Willden, Kurtis

1992-01-01

Braided composite materials, one of the advanced material forms which is under investigation in Boeing's ATCAS program, have been recognized as a potential cost-effective material form for fuselage structural elements. Consequently, there is a strong need for more knowledge in the design, manufacture, test, and analysis of textile structural composites. The overall objective of this work is to advance braided composite technology towards applications to a large commercial transport fuselage. This paper summarizes the mechanics of materials and manufacturing demonstration results which have been obtained in order to acquire an understanding of how braided composites can be applied to a commercial fuselage. Textile composites consisting of 1D, 2D triaxial, and 3D braid patterns with thermoplastic and two RTM resin systems were investigated. The structural performance of braided composites was evaluated through an extensive mechanical test program. Analytical methods were also developed and applied to predict the following: internal fiber architectures, stiffnesses, fiber stresses, failure mechanisms, notch effects, and the entire history of failure of the braided composites specimens. The applicability of braided composites to a commercial transport fuselage was further assessed through a manufacturing demonstration. Three foot fuselage circumferential hoop frames were manufactured to demonstrate the feasibility of consistently producing high quality braided/RTM composite primary structures. The manufacturing issues (tooling requirements, processing requirements, and process/quality control) addressed during the demonstration are summarized. The manufacturing demonstration in conjunction with the mechanical test results and developed analytical methods increased the confidence in the ATCAS approach to the design, manufacture, test, and analysis of braided composites.

Advanced powder metallurgy aluminum alloys and composites

Science.gov (United States)

Lisagor, W. B.; Stein, B. A.

1982-01-01

The differences between powder and ingot metallurgy processing of aluminum alloys are outlined. The potential payoff in the use of advanced powder metallurgy (PM) aluminum alloys in future transport aircraft is indicated. The national program to bring this technology to commercial fruition and the NASA Langley Research Center role in this program are briefly outlined. Some initial results of research in 2000-series PM alloys and composites that highlight the property improvements possible are given.

Multi scale analysis by acoustic emission of damage mechanisms in natural fibre woven fabrics/epoxy composites.

Directory of Open Access Journals (Sweden)

Touchard F.

2010-06-01

Full Text Available This paper proposes to develop an experimental program to characterize the type and the development of damage in composite with complex microstructure. A multi-scale analysis by acoustic emission has been developed and applied to hemp fibre woven fabrics/epoxy composite. The experimental program consists of tensile tests performed on single yarn, neat epoxy resin and composite materials to identify their AE amplitude signatures. A statistical analysis of AE amplitude signals has been realised and correlated with microscopic observations. Results have enabled to identify three types of damage in composites and their associated AE amplitudes: matrix cracking, interfacial debonding and reinforcement damage and fracture. Tracking of these damage mechanisms in hemp/epoxy composites has been performed to show the process of damage development in natural fibre reinforced composites.

Dating Violence and Sexual Assault Prevention with African American Middle Schoolers: Does Group Gender Composition Impact Dating Violence Attitudes?

Science.gov (United States)

Black, Beverly M.; Weisz, Arlene N.; Jayasundara, Dheeshana S.

2012-01-01

A dating violence and sexual assault prevention program was presented to 396, predominately African American, middle schoolers in two inner city schools in the United States. In one school the program was offered with a same-gender group composition; in the other school, the same program was offered with mixed-gender group composition. A…

Structural Acoustic Physics Based Modeling of Curved Composite Shells

Science.gov (United States)

2017-09-19

NUWC-NPT Technical Report 12,236 19 September 2017 Structural Acoustic Physics -Based Modeling of Curved Composite Shells Rachel E. Hesse...SUBTITLE Structural Acoustic Physics -Based Modeling of Curved Composite Shells 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT...study was to use physics -based modeling (PBM) to investigate wave propagations through curved shells that are subjected to acoustic excitation. An

In vivo body composition studies in malnourished patients

International Nuclear Information System (INIS)

Allen, B.J.; Blagojevic, N.

1987-01-01

The establishment of an in vivo TBN facility at Lucas Heights, together with measurement techniques for whole body and extracellular water, is leading to an expanded interest in the relationships between clinical status, body composition and dietary regimes. The ANSTO program provides the opportunity for the first quantitative assessments of these factors in Australia. Body composition studies provide a common link with other-wise unrelated physiological or psychological diseases, and a pool of normal data is being established. Substantial improvements in patient care and quality of life should result from this project, together with a deeper understanding of the importance of body composition in disease-induced malnutrition

In vivo body composition studies in malnourished patients

Energy Technology Data Exchange (ETDEWEB)

Allen, B J; Blagojevic, N

1987-09-01

The establishment of an in vivo TBN facility at Lucas Heights, together with measurement techniques for whole body and extracellular water, is leading to an expanded interest in the relationships between clinical status, body composition and dietary regimes. The ANSTO program provides the opportunity for the first quantitative assessments of these factors in Australia. Body composition studies provide a common link with other-wise unrelated physiological or psychological diseases, and a pool of normal data is being established. Substantial improvements in patient care and quality of life should result from this project, together with a deeper understanding of the importance of body composition in disease-induced malnutrition.

Using laser absorption spectroscopy to monitor composition and physical properties of metal vapors

International Nuclear Information System (INIS)

Berzins, L.V.

1993-01-01

The Atomic Vapor Laser Isotope Separation (AVLIS) program has been using laser absorption spectroscopy to monitor vapor densities for over 15 years. Laser absorption spectroscopy has proven itself to be an accurate and reliable method to monitor both density and composition. During this time the diagnostic has moved from a research tool toward a robust component of a process control system. The hardware used for this diagnostic is discussed elsewhere at this symposium. This paper describes how the laser absorption spectroscopy diagnostic is used as a component of a process control system as well as supplying detailed measurements on vapor densities, composition, flow velocity, internal and kinetic temperatures, and constituent distributions. Examples will be drawn from the uranium AVLIS program. In addition potential applications such as composition control in the production of metal matrix composites or aircraft alloys will be discussed

Micromechanisms of damage in unidirectional fiber reinforced composites

DEFF Research Database (Denmark)

Mishnaevsky, Leon; Brøndsted, Povl

2009-01-01

strength of a composite at the pre-critical load, while the fibers with randomly distributed strengths lead to the higher strength of the composite at post-critical loads. In the case of randomly distributed fiber strengths, the damage growth in fibers seems to be almost independent from the crack length...... in the numerical experiments. The effect of the statistical variability of fiber strengths, viscosity of the polymer matrix as well as the interaction between the damage processes in matrix, fibers and interface are investigated numerically. It is demonstrated that fibers with constant strength ensure higher......Numerical micromechanical investigations of the mechanical behavior and damage evolution of glass fiber reinforced composites are presented. A program code for the automatic generation of 3D micromechanical unit cell models of composites with damageable elements is developed, and used...

STREAM: A First Programming Process

DEFF Research Database (Denmark)

Caspersen, Michael Edelgaard; Kölling, Michael

2009-01-01

to derive a programming process, STREAM, designed specifically for novices. STREAM is a carefully down-scaled version of a full and rich agile software engineering process particularly suited for novices learning object-oriented programming. In using it we hope to achieve two things: to help novice......Programming is recognized as one of seven grand challenges in computing education. Decades of research have shown that the major problems novices experience are composition-based—they may know what the individual programming language constructs are, but they do not know how to put them together....... Despite this fact, textbooks, educational practice, and programming education research hardly address the issue of teaching the skills needed for systematic development of programs. We provide a conceptual framework for incremental program development, called Stepwise Improvement, which unifies best...

Analytical method for predicting plastic flow in notched fiber composite materials

International Nuclear Information System (INIS)

Flynn, P.L.; Ebert, L.J.

1977-01-01

An analytical system was developed for prediction of the onset and progress of plastic flow of oriented fiber composite materials in which both externally applied complex stress states and stress raisers were present. The predictive system was a unique combination of two numerical systems, the ''SAAS II'' finite element analysis system and a micromechanics finite element program. The SAAS II system was used to generate the three-dimensional stress distributions, which were used as the input into the finite element micromechanics program. Appropriate yielding criteria were then applied to this latter program. The accuracy of the analytical system was demonstrated by the agreement between the analytically predicted and the experimentally measured flow values of externally notched tungsten wire reinforced copper oriented fiber composites, in which the fiber fraction was 50 vol pct

BILAM: a composite laminate failure-analysis code using bilinear stress-strain approximations

Energy Technology Data Exchange (ETDEWEB)

McLaughlin, P.V. Jr.; Dasgupta, A.; Chun, Y.W.

1980-10-01

The BILAM code which uses constant strain laminate analysis to generate in-plane load/deformation or stress/strain history of composite laminates to the point of laminate failure is described. The program uses bilinear stress-strain curves to model layer stress-strain behavior. Composite laminates are used for flywheels. The use of this computer code will help to develop data on the behavior of fiber composite materials which can be used by flywheel designers. In this program the stress-strain curves are modelled by assuming linear response in axial tension while using bilinear approximations (2 linear segments) for stress-strain response to axial compressive, transverse tensile, transverse compressive and axial shear loadings. It should be noted that the program attempts to empirically simulate the effects of the phenomena which cause nonlinear stress-strain behavior, instead of mathematically modelling the micromechanics involved. This code, therefore, performs a bilinear laminate analysis, and, in conjunction with several user-defined failure interaction criteria, is designed to provide sequential information on all layer failures up to and including the first fiber failure. The modus operandi is described. Code BILAM can be used to: predict the load-deformation/stress-strain behavior of a composite laminate subjected to a given combination of in-plane loads, and make analytical predictions of laminate strength.

Developmental assessment of the Fort St. Vrain version of the composite HTGR analysis program (CHAP-2)

International Nuclear Information System (INIS)

Stroh, K.R.

1981-01-01

The Composite HTGR Analysis Program (CHAP) consists of a model-independent systems analysis mainframe named LASAN and model-dependent linked code modules, each representing a component, subsystem, or phenomenon of an HTGR plant. The Fort St. Vrain version (CHAP-2) includes 21 coded modules that model the neutron kinetics and thermal response of the core; the thermal-hydraulics of the reactor primary coolant system, secondary steam supply system, and balance-of-plant; the actions of the control system and plant protection system; the response of the reactor building; and the relative hazard resulting from fuel particle failure. FSV steady-state and transient plant data are being used to partially verify the component modeling and dynamic simulation techniques used to predict plant response to postulated accident sequences. Results of these preliminary validation efforts are presented showing good agreement between code output and plant data for the portions of the code that have been tested. Plans for further development and assessment as well as application of the validated code are discussed. (author)

Computing Equilibrium Chemical Compositions

Science.gov (United States)

Mcbride, Bonnie J.; Gordon, Sanford

1995-01-01

Chemical Equilibrium With Transport Properties, 1993 (CET93) computer program provides data on chemical-equilibrium compositions. Aids calculation of thermodynamic properties of chemical systems. Information essential in design and analysis of such equipment as compressors, turbines, nozzles, engines, shock tubes, heat exchangers, and chemical-processing equipment. CET93/PC is version of CET93 specifically designed to run within 640K memory limit of MS-DOS operating system. CET93/PC written in FORTRAN.

Composite Measures of Health Care Provider Performance: A Description of Approaches

Science.gov (United States)

Shwartz, Michael; Restuccia, Joseph D; Rosen, Amy K

2015-01-01

Context Since the Institute of Medicine’s 2001 report Crossing the Quality Chasm, there has been a rapid proliferation of quality measures used in quality-monitoring, provider-profiling, and pay-for-performance (P4P) programs. Although individual performance measures are useful for identifying specific processes and outcomes for improvement and tracking progress, they do not easily provide an accessible overview of performance. Composite measures aggregate individual performance measures into a summary score. By reducing the amount of data that must be processed, they facilitate (1) benchmarking of an organization’s performance, encouraging quality improvement initiatives to match performance against high-performing organizations, and (2) profiling and P4P programs based on an organization’s overall performance. Methods We describe different approaches to creating composite measures, discuss their advantages and disadvantages, and provide examples of their use. Findings The major issues in creating composite measures are (1) whether to aggregate measures at the patient level through all-or-none approaches or the facility level, using one of the several possible weighting schemes; (2) when combining measures on different scales, how to rescale measures (using z scores, range percentages, ranks, or 5-star categorizations); and (3) whether to use shrinkage estimators, which increase precision by smoothing rates from smaller facilities but also decrease transparency. Conclusions Because provider rankings and rewards under P4P programs may be sensitive to both context and the data, careful analysis is warranted before deciding to implement a particular method. A better understanding of both when and where to use composite measures and the incentives created by composite measures are likely to be important areas of research as the use of composite measures grows. PMID:26626986

Synthesis and processing of composites by reactive metal penetration

Energy Technology Data Exchange (ETDEWEB)

Loehman, R.E.; Ewsuk, K.G. [Sandia National Laboratories, Albuquerque, NM (United States); Tomsia, A.P. [Pask Research and Engineering, Berkeley, CA (United States)] [and others

1995-05-01

Ceramic-metal composites are being developed because their high stiffness-to weight ratios, good fracture toughness, and variable electrical and thermal properties give them advantages over more conventional materials. However, because ceramic-metal composite components presently are more expensive than monolithic materials, improvements in processing are required to reduce manufacturing costs. Reactive metal penetration is a promising new method for making ceramic- and metal-matrix composites that has the advantage of being inherently a net-shape process. This technique, once fully developed, will provide another capability for manufacturing the advanced ceramic composites that are needed for many light-weight structural and wear applications. The lower densities of these composites lead directly to energy savings in use. Near-net-shape fabrication of composite parts should lead to additional savings because costly and energy intensive grinding and machining operations are significantly reduced, and the waste generated from such finishing operations is minimized. The goals of this research program are: (1) to identify feasible compositional systems for making composites by reactive metal penetration; (2) to understand the mechanism(s) of composite formation by reactive metal penetration; and (3) to learn how to control and optimize reactive metal penetration for economical production of composites and composite coatings.

Composites Materials and Manufacturing Technologies for Space Applications

Science.gov (United States)

Vickers, J. H.; Tate, L. C.; Gaddis, S. W.; Neal, R. E.

2016-01-01

Composite materials offer significant advantages in space applications. Weight reduction is imperative for deep space systems. However, the pathway to deployment of composites alternatives is problematic. Improvements in the materials and processes are needed, and extensive testing is required to validate the performance, qualify the materials and processes, and certify components. Addressing these challenges could lead to the confident adoption of composites in space applications and provide spin-off technical capabilities for the aerospace and other industries. To address the issues associated with composites applications in space systems, NASA sponsored a Technical Interchange Meeting (TIM) entitled, "Composites Materials and Manufacturing Technologies for Space Applications," the proceedings of which are summarized in this Conference Publication. The NASA Space Technology Mission Directorate and the Game Changing Program chartered the meeting. The meeting was hosted by the National Center for Advanced Manufacturing (NCAM)-a public/private partnership between NASA, the State of Louisiana, Louisiana State University, industry, and academia, in association with the American Composites Manufacturers Association. The Louisiana Center for Manufacturing Sciences served as the coordinator for the TIM.

Methods for robustness programming

NARCIS (Netherlands)

Olieman, N.J.

2008-01-01

Robustness of an object is defined as the probability that an object will have properties as required. Robustness Programming (RP) is a mathematical approach for Robustness estimation and Robustness optimisation. An example in the context of designing a food product, is finding the best composition

Optimal fabrication processes for unidirectional metal-matrix composites: A computational simulation

Science.gov (United States)

Saravanos, D. A.; Murthy, P. L. N.; Morel, M.

1990-01-01

A method is proposed for optimizing the fabrication process of unidirectional metal matrix composites. The temperature and pressure histories are optimized such that the residual microstresses of the composite at the end of the fabrication process are minimized and the material integrity throughout the process is ensured. The response of the composite during the fabrication is simulated based on a nonlinear micromechanics theory. The optimal fabrication problem is formulated and solved with non-linear programming. Application cases regarding the optimization of the fabrication cool-down phases of unidirectional ultra-high modulus graphite/copper and silicon carbide/titanium composites are presented.

Optimal fabrication processes for unidirectional metal-matrix composites - A computational simulation

Science.gov (United States)

Saravanos, D. A.; Murthy, P. L. N.; Morel, M.

1990-01-01

A method is proposed for optimizing the fabrication process of unidirectional metal matrix composites. The temperature and pressure histories are optimized such that the residual microstresses of the composite at the end of the fabrication process are minimized and the material integrity throughout the process is ensured. The response of the composite during the fabrication is simulated based on a nonlinear micromechanics theory. The optimal fabrication problem is formulated and solved with nonlinear programming. Application cases regarding the optimization of the fabrication cool-down phases of unidirectional ultra-high modulus graphite/copper and silicon carbide/titanium composites are presented.

Programs as Polypeptides.

Science.gov (United States)

Williams, Lance R

2016-01-01

Object-oriented combinator chemistry (OOCC) is an artificial chemistry with composition devices borrowed from object-oriented and functional programming languages. Actors in OOCC are embedded in space and subject to diffusion; since they are neither created nor destroyed, their mass is conserved. Actors use programs constructed from combinators to asynchronously update their own states and the states of other actors in their neighborhoods. The fact that programs and combinators are themselves reified as actors makes it possible to build programs that build programs from combinators of a few primitive types using asynchronous spatial processes that resemble chemistry as much as computation. To demonstrate this, OOCC is used to define a parallel, asynchronous, spatially distributed self-replicating system modeled in part on the living cell. Since interactions among its parts result in the construction of more of these same parts, the system is strongly constructive. The system's high normalized complexity is contrasted with that of a simple composome.

Wear resistant composite structure of vitreous carbon containing convoluted fibers. Final report

Energy Technology Data Exchange (ETDEWEB)

Burton, R.G.; Burton, R.A.

1996-05-28

Energy Related Inventions Program Number 613 was a two year program to commercialize a unique new wear material, Metal Reinforced Carbon Composite, MRCC. The program was designed to manufacture sample components of MRCC for evaluation by potential users and manufacturers. As a result of the program Burton Technologies Inc. and Rotary Power International are forming a joint company to manufacture, market and license MRCC materials to a wide range of industries.

Effects of Combined Vigorous Interval Training Program and Diet on Body Composition, Physical Fitness, and Physical Self-Perceptions Among Obese Adolescent Boys and Girls.

Science.gov (United States)

Rey, Olivier; Vallier, Jean-Marc; Nicol, Caroline; Mercier, Charles-Symphorien; Maïano, Christophe

2017-02-01

This study examined the effects of a five-week intervention combining vigorous interval training (VIT) with diet among twenty-four obese adolescents. Fourteen girls and ten boys (aged 14-15) schooled in a pediatric rehabilitation center participated. The VIT intensity was targeted and remained above 80% of maximal heart rate (HR) and over six kilocalories per minute. Pre- and postintervention measures were body composition (BMI, weight, body fat percentage), physical self-perceptions (PSP), physical fitness (6-min walking distance and work) and its associated physiological responses (HR peak and blood lactate concentration). A series of two-way analyses of variance or covariance controlling for weight loss were used to examine the changes. Significant improvements were found in body composition, physical fitness and PSP (endurance, activity level, sport competence, global physical self-concept and appearance). In addition, boys presented higher levels of perceived strength and global physical self-concept than girls. Finally, there was a significant increase in perceived endurance, sport competence, and global physical self-concept in girls only. This five-week VIT program combined with diet represents an effective means for improving body composition, physical fitness, and PSP in obese adolescents, the effects on PSP being larger among girls.

Effect of Spinning Cycling Training on Body Composition in Women

Science.gov (United States)

Kaya, Fatih; Nar, Dilek; Erzeybek, Mustafa Said

2018-01-01

In this study the effects of a 6 week spinning cycling training on the body composition of women were investigated. Twelve sedentary women (32-47 years old) voluntarily participated in this study. The 6-week training program consisted of exercise sessions on 3 days per week. The intensity of the training program that was kept low in the beginning…

Improving body composition and strength in athletes through a 4-month combined martial arts and strength training program

Directory of Open Access Journals (Sweden)

Aleksandra Stachoń

2016-06-01

2Zakład Sportów Indywidualnych, Akademia Wychowania Fizycznego, ul. Paderewskiego 35, Wrocław       Corresponding author: Dr Aleksandra Jadwiga Stachoń, e-mail: aleksandra.stachon@awf.wroc.pl Departament of Physical Anthropology, University School of Physical Education in Wrocław, al. I.J. Paderewskiego 35, bud. P2, 51-612 Wrocław; Poland Phone: 71 347 33 44         Key words: resistance training, body build, body composition, combat sport.   Abstract Background and aim. Body composition is one of key components of health in both general and athletic populations. In martial arts great significance is attached to the development of mesomorphy and strength, which are crucial for performing offensive and defensive actions during fights. The study proposes to introduce progressive strength training programme - arranged primarily for beginners – in order to improve body composition of non-elite male martial arts competitors. The present study aims to evaluate the changes in body massiveness, body composition and strength in 31 martial arts practitioners from academic sports clubs after a combined martial arts and strength training programme. Material and methods. The 16-week intervention was based on a targeted progressive resistance training protocol developed by Stefaniak [1995]. The anthropometric, physical and motoric measurements were performed twice at four months interval. This programme includes training three times weekly with increased number of repetitions (19-24, number of sets (1-3 and increased loads (5%. Results. After the completion of the training program, significant increase for about 1.8 kgin body mass was observed. Body massiveness (BMI increased from 23.2 ± 1.8 kg/m2 to 23.9 ± 1.8 kg/m2. The analysis using Sheldon’s somatotypes revealed an increase of mesomorphy (from 5.5 to 5.7 and decrease of ectomorphy (from 2.5 to 2.4. The level of endomorphy became stable (2.1. The maximal circumferences of flexed arm, forearm, calf and

Program Evaluation - Automotive Lightweighting Materials Program Research and Development Projects Assessment of Benefits - Case Studies No. 2

Energy Technology Data Exchange (ETDEWEB)

Das, S.

2003-01-23

This report is the second of a series of studies to evaluate research and development (R&D) projects funded by the Automotive Lightweighting Materials (ALM) Program of the Office of Advanced Automotive Technologies (OAAT) of the U.S. Department of Energy (DOE). The objectives of the program evaluation are to assess short-run outputs and long-run outcomes that may be attributable to the ALM R&D projects. The ALM program focuses on the development and validation of advanced technologies that significantly reduce automotive vehicle body and chassis weight without compromising other attributes such as safety, performance, recyclability, and cost. Funded projects range from fundamental materials science research to applied research in production environments. Collaborators on these projects include national laboratories, universities, and private sector firms, such as leading automobile manufacturers and their suppliers. Three ALM R&D projects were chosen for this evaluation: Design and Product Optimization for Cast Light Metals, Durability of Lightweight Composite Structures, and Rapid Tooling for Functional Prototyping of Metal Mold Processes. These projects were chosen because they have already been completed. The first project resulted in development of a comprehensive cast light metal property database, an automotive application design guide, computerized predictive models, process monitoring sensors, and quality assurance methods. The second project, the durability of lightweight composite structures, produced durability-based design criteria documents, predictive models for creep deformation, and minimum test requirements and suggested test methods for establishing durability properties and characteristics of random glass-fiber composites for automotive structural composites. The durability project supported Focal Project II, a validation activity that demonstrates ALM program goals and reduces the lead time for bringing new technology into the marketplace. Focal

Development of pressure containment and damage tolerance technology for composite fuselage structures in large transport aircraft

Science.gov (United States)

Smith, P. J.; Thomson, L. W.; Wilson, R. D.

1986-01-01

NASA sponsored composites research and development programs were set in place to develop the critical engineering technologies in large transport aircraft structures. This NASA-Boeing program focused on the critical issues of damage tolerance and pressure containment generic to the fuselage structure of large pressurized aircraft. Skin-stringer and honeycomb sandwich composite fuselage shell designs were evaluated to resolve these issues. Analyses were developed to model the structural response of the fuselage shell designs, and a development test program evaluated the selected design configurations to appropriate load conditions.

Multifunctional Metal/Polymer Composite Fiber for Space Applications, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — In this Small Business Innovation Research Phase I Program, Syscom Technology, Inc. (STI) will fabricate a metallized multifunctional composite fiber from a...

Real-Time X-Ray Inspection of Composite Aircraft Structures

National Research Council Canada - National Science Library

Patricelli, F

1978-01-01

...) for detection of defects, damage, and repair verification. The program included inspection of composite aircraft structural samples in the laboratory and an on site demonstration of RTR at the Naval Air Rework Facility (NARF...

Phytoremediation of Composition-B Derived TNT and RDX in Herbaceous Plant-vegetated and Bare Lysimeters

Science.gov (United States)

2009-12-01

ER D C TR -0 9- 10 Strategic Environmental Research and Development Program Phytoremediation of Composition-B Derived TNT and RDX in...Program ERDC TR-09-10 December 2009 Phytoremediation of Composition-B Derived TNT and RDX in Herbaceous Plant-vegetated and Bare Lysimeters Elly P. H...for U.S. Army Corps of Engineers Washington, DC 20314-1000 ERDC TR-09-10 ii Abstract: This report describes a study in which phytoremediation of

NASA-UVa light aerospace alloy and structures technology program

Science.gov (United States)

Gangloff, Richard P.; Haviland, John K.; Herakovich, Carl T.; Pilkey, Walter D.; Pindera, Marek-Jerzy; Scully, John R.; Stoner, Glenn E.; Swanson, Robert E.; Thornton, Earl A.; Wawner, Franklin E., Jr.

1991-01-01

The general objective of the NASA-UVa Light Aerospace Alloy and Structures Technology Program was to conduct research on the performance of next generation, light weight aerospace alloys, composites, and associated thermal gradient structures. The following research areas were actively investigated: (1) mechanical and environmental degradation mechanisms in advanced light metals and composites; (2) aerospace materials science; (3) mechanics of materials and composites for aerospace structures; and (4) thermal gradient structures.

"ComPost": A Writing Program Newsletter and Its Rationale.

Science.gov (United States)

Hall, Dennis R.

1993-01-01

Discusses the development and rationale of "ComPost," a weekly newsletter of the Composition Program at the University of Louisville. Suggests that a vehicle like ComPost can promote the communications that contribute to accomplishing collegiality and genuine program consensus. (RS)

Fiber Finishes for Improving Galvanic Resistance of Imide-Based Composites

National Research Council Canada - National Science Library

Allred, R. E

1998-01-01

The objective of this program is the development and demonstration of galvanic corrosion resistant carbon/ BMI composites through the use of reactive finishes to form coatings that isolate the carbon...

User's manual for the Composite HTGR Analysis Program (CHAP-1)

International Nuclear Information System (INIS)

Gilbert, J.S.; Secker, P.A. Jr.; Vigil, J.C.; Wecksung, M.J.; Willcutt, G.J.E. Jr.

1977-03-01

CHAP-1 is the first release version of an HTGR overall plant simulation program with both steady-state and transient solution capabilities. It consists of a model-independent systems analysis program and a collection of linked modules, each representing one or more components of the HTGR plant. Detailed instructions on the operation of the code and detailed descriptions of the HTGR model are provided. Information is also provided to allow the user to easily incorporate additional component modules, to modify or replace existing modules, or to incorporate a completely new simulation model into the CHAP systems analysis framework

Polymer/Layered Silicate Nano composites

International Nuclear Information System (INIS)

Bakhit, M.E.E.H.

2012-01-01

Polymer–clay nano composites have attracted the attention of many researchers and experimental results are presented in a large number of recent papers and patents because of the outstanding mechanical properties and low gas permeabilities that are achieved in many cases. Polymer-clay nano composites are a new class of mineral-field polymer that contain relatively small amounts (<10%) of nanometer-sized clay particles. Polymer/clay nano composites have their origin in the pioneering research conducted at Toyota Central Research Laboratories and the first historical record goes back to 1987. The matrix was nylon-6 and the filler MMT. Because of its many advantages such as high mechanical properties, good gas barrier, flame retardation, etc. polymer/clay nano composites have been intensely investigated and is currently the subject of many research programs. Nano composite materials are commercially important and several types of products with different shapes and applications including food packaging films and containers, engine parts, dental materials, etc. are now available in markets. A number of synthesis routes have been developed in the recent years to prepare these materials, which include intercalation of polymers or prepolymers from solution, in-situ polymerization, melt intercalation etc. In this study, new nano composite materials were produced from the components of rubber (Nbr, SBR and EPDM) as the polymeric matrix and organically modified quaternary alkylammonium montmorillonite in different contents (3, 5, 7, and 10 phr) as the filler by using an extruder then, the rubber nano composite sheets were irradiated at a dose of 0, 50, 75, 100 and 150 KGy using Electron beam Irradiation technique as a crosslinking agent. These new materials can be characterized by using various analytical techniques including X-ray diffractometer XRD, Thermogravimetric analyzer TGA, scanning electron microscope (SEM), transmission electron microscope (TEM),Fourier transform

Protective Skins for Composite Airliners

Science.gov (United States)

Johnson, Vicki S.; Boone, Richard L.; Jones, Shannon; Pendse, Vandana; Hayward, Greg

2014-01-01

Traditional composite aircraft structures are designed for load bearing and then overdesigned for impact damage and hot humid environments. Seeking revolutionary improvement in the performance and weight of composite structures, Cessna Aircraft Company, with sponsorship from the NASA Fundamental Aeronautics Program/Subsonic Fixed Wing Project, has developed and tested a protective skin concept which would allow the primary composite structure to carry only load and would meet the impact, hot and humid, and other requirements through protective skins. A key requirement for the protective skins is to make any impact damage requiring repair visible. Testing from the first generation of skins helped identify the most promising materials which were used in a second generation of test articles. This report summarizes lessons learned from the first generation of protective skins, the design and construction of the second-generation test articles, test results from the second generation for impact, electromagnetic effects, aesthetics and smoothing, thermal, and acoustic (for the first time), and an assessment of the feasibility of the protective skin concept.

Inelastic damage using continuum damage mechanics in composite plate reinforced by unidirectional fibers

Directory of Open Access Journals (Sweden)

Žmindák Milan

2018-01-01

Full Text Available It is well that a finite element method is very popular simulation method to predict the physical behavior of systems and structures. In the last years an increase of interest in a new type of numerical methods known as meshless methods was observed. The paper deals with application of radial basis functions on modelling of inelastic damage using continuum damage mechanics of layered plate composite structures reinforced with long unidirectional fibers. For numerical simulations of elastic-plastic damage of layered composite plates own computational programs were implemented in MATLAB programming language. We will use the Newton-Raphson method to solve nonlinear systems of equations. Evaluation damage during plasticity has been solved using return mapping algorithm. The results of elastic-plastic damage analysis of composite plate with unsymmetrical laminate stacking sequence are presented.

Determining Composite Validity Coefficients for Army Jobs and Job Families

National Research Council Canada - National Science Library

Zeidner, Joseph

2002-01-01

...) is to compute composite validity coefficients. using criterion data derived from the 1987 - 1989 Skill Qualifications Test program, for the 7-test ASVAB for 150, 17, and 9 job family structures...

Free material stiffness design of laminated composite structures using commercial finite element analysis codes

DEFF Research Database (Denmark)

Henrichsen, Søren Randrup; Lindgaard, Esben; Lund, Erik

2015-01-01

In this work optimum stiffness design of laminated composite structures is performed using the commercially available programs ANSYS and MATLAB. Within these programs a Free Material Optimization algorithm is implemented based on an optimality condition and a heuristic update scheme. The heuristic...... update scheme is needed because commercially available finite element analysis software is used. When using a commercial finite element analysis code it is not straight forward to implement a computationally efficient gradient based optimization algorithm. Examples considered in this work are a clamped......, where full access to the finite element analysis core is granted. This comparison displays the possibility of using commercially available programs for stiffness design of laminated composite structures....

An introduction to compositional methods for concurrency and their application to real-time

NARCIS (Netherlands)

Hooman, J.J.M.; Roever, de W.P.

1992-01-01

Formal methods to specify and verify concurrent programs with synchronous message passing are discussed. We stress the development towards compositional methods, i.e. methods in which the specification of a compound program can be inferred from specifications of its constituents without reference to

Fatigue of hybrid glass/carbon composites: 3D computational studies

DEFF Research Database (Denmark)

Dai, Gaoming; Mishnaevsky, Leon

2014-01-01

3D computational simulations of fatigue of hybrid carbon/glass fiber reinforced composites is carried out using X-FEM and multifiber unit cell models. A new software code for the automatic generation of unit cell multifiber models of composites with randomly misaligned fibers of various properties...... and geometrical parameters is developed. With the use of this program code and the X-FEM method, systematic investigations of the effect of microstructure of hybrid composites (fraction of carbon versus glass fibers, misalignment, and interface strength) and the loading conditions (tensile versus compression...... cyclic loading effects) on fatigue behavior of the materials are carried out. It was demonstrated that the higher fraction of carbon fibers in hybrid composites is beneficial for the fatigue lifetime of the composites under tension-tension cyclic loading, but might have negative effect on the lifetime...

A Study of the Utilization of Advanced Composites in Fuselage Structures of Commercial Aircraft

Science.gov (United States)

Watts, D. J.; Sumida, P. T.; Bunin, B. L.; Janicki, G. S.; Walker, J. V.; Fox, B. R.

1985-01-01

A study was conducted to define the technology and data needed to support the introduction of advanced composites in the future production of fuselage structure in large transport aircraft. Fuselage structures of six candidate airplanes were evaluated for the baseline component. The MD-100 was selected on the basis of its representation of 1990s fuselage structure, an available data base, its impact on the schedule and cost of the development program, and its availability and suitability for flight service evaluation. Acceptance criteria were defined, technology issues were identified, and a composite fuselage technology development plan, including full-scale tests, was identified. The plan was based on composite materials to be available in the mid to late 1980s. Program resources required to develop composite fuselage technology are estimated at a rough order of magnitude to be 877 man-years exclusive of the bird strike and impact dynamic test components. A conceptual composite fuselage was designed, retaining the basic MD-100 structural arrangement for doors, windows, wing, wheel wells, cockpit enclosure, major bulkheads, etc., resulting in a 32 percent weight savings.

Proceedings of the SERI Biomass Program Principal Investigators' Review Meeting: Aquatic Species Program Reports; 23-25 June 1982, Washington, DC

Energy Technology Data Exchange (ETDEWEB)

1982-12-01

The Aquatic Species Program (ASP) is concerned with how plant biomass that naturally occurs in wetland or submerged areas is utilized. Processes are being developed in this program to make use of those aquatic species, capitalizing on their inherent capacity for rapid growth as well as on their extraordinary chemical compositions.

Evaluation of the impact of a nutritional program for undernourished children in Brazil

NARCIS (Netherlands)

Santos, Iná S; Gigante, Denise P; Coitinho, Denise C; Haisma, Hinke; Valle, Neiva C J; Valente, Gicele

2005-01-01

To assess the effectiveness on child growth and body composition of a supplementary feeding program (Milk Supplement Program), a prospective, controlled study was conducted in Northeast Brazil. When entering the Program, children from 10 municipalities with the highest coverage rates in the Program

VEST: An Aspect-Based Composition Tool for Real-Time Systems

Science.gov (United States)

2003-01-01

VEST: An Aspect-Based Composition Tool for Real - Time Systems * John A. Stankovic Ruiqing Zhu Ram Poornalingam Chenyang Lu Zhendong Yu Marty Humphrey...Composition Tool for Real - Time Systems 5a. CONTRACT NUMBER 5b. GRANT NUMBER 5c. PROGRAM ELEMENT NUMBER 6. AUTHOR(S) 5d. PROJECT NUMBER 5e. TASK...it is obvious that designers of embedded real - time systems face many difficult problems. By working through various product scenarios with avionics

Development and validation of bonded composite doubler repairs for commercial aircraft.

Energy Technology Data Exchange (ETDEWEB)

Roach, Dennis Patrick; Rackow, Kirk A.

2007-07-01

A typical aircraft can experience over 2,000 fatigue cycles (cabin pressurizations) and even greater flight hours in a single year. An unavoidable by-product of aircraft use is that crack, impact, and corrosion flaws develop throughout the aircraft's skin and substructure elements. Economic barriers to the purchase of new aircraft have placed even greater demands on efficient and safe repair methods. The use of bonded composite doublers offers the airframe manufacturers and aircraft maintenance facilities a cost effective method to safely extend the lives of their aircraft. Instead of riveting multiple steel or aluminum plates to facilitate an aircraft repair, it is now possible to bond a single Boron-Epoxy composite doubler to the damaged structure. The FAA's Airworthiness Assurance Center at Sandia National Labs (AANC), Boeing, and Federal Express completed a pilot program to validate and introduce composite doubler repair technology to the U.S. commercial aircraft industry. This project focused on repair of DC-10 fuselage structure and its primary goal was to demonstrate routine use of this repair technology using niche applications that streamline the design-to-installation process. As composite doubler repairs gradually appear in the commercial aircraft arena, successful flight operation data is being accumulated. These commercial aircraft repairs are not only demonstrating the engineering and economic advantages of composite doubler technology but they are also establishing the ability of commercial maintenance depots to safely adopt this repair technique. This report presents the array of engineering activities that were completed in order to make this technology available for widespread commercial aircraft use. Focused laboratory testing was conducted to compliment the field data and to address specific issues regarding damage tolerance and flaw growth in composite doubler repairs. Fatigue and strength tests were performed on a simulated wing

Processing and characterization of ceramic superconductor/polymer composites

International Nuclear Information System (INIS)

Kander, R.G.; Namboodri, S.L.

1993-01-01

One way to more easily process a brittle high-temperature ceramic superconductor into a useful structure is to combine it with a polymer to form a composite material. Processing of polymer-based composites into complex shapes is well established and relatively easy when compared with traditional ceramic processing unit operations. In addition, incorporating a ceramic superconductor into a polymer matrix can improve mechanical performance as compared with a monolithic ceramic. Finally, because ceramic superconductors are susceptible to attack by moisture, a polymer-based composite structure can also provide protection from deleterious environmental effects. This paper focuses on the processing and subsequent characterization of ceramic superconductor/polymer composites designed primarily for electromagnetic shielding and diamagnetic applications. YBa 2 Cu 3 O 7-x [YBCO] ceramic superconductor is combined with poly(methyl methacrylate) [PMMA] to form novel composite structures. Composite structures have been molded with both a discontinuous superconducting phase (i.e., ceramic particulate reinforced polymers) and with a continuous superconducting phase (i.e., polymer infiltrated porous ceramics). Characterization of these composite structures includes the determination of diamagnetic strength, electromagnetic shielding effectiveness, mechanical performance, and environmental resistance. The goal of this program is to produce a composite structure with increased mechanical integrity and environmental resistance at liquid nitrogen temperatures without compromising the electromagnetic shielding and diamagnetic properties of the superconducting phase. Composites structures of this type are potentially useful in numerous magnetic applications including electromagnetic shielding, magnetic sensors, energy storage, magnetic levitation, and motor windings

Ceramic composites for near term reactor application - HTR2008-58050

International Nuclear Information System (INIS)

Snead, L. L.; Katoh, Y.; Windes, W. E.; Shinavski, R. J.; Burchell, T. D.

2008-01-01

Currently, two composites types are being developed for in-core application: carbon fiber carbon composite (CFC), and silicon carbide fiber composite (SiC/SiC.) Irradiation effects studies have been carried out over the past few decades yielding radiation-tolerant CFC's and a composite of SiC/SiC with no apparent degradation in mechanical properties to very high neutron exposure. While CFC's can be engineered with significantly higher thermal conductivity, and a slight advantage in manufacturability than SiC/SiC, they do have a neutron irradiation-limited lifetime. The SiC composite, while possessing lower thermal conductivity (especially following irradiation), appears to have mechanical properties insensitive to irradiation. Both materials are currently being produced to sizes much larger than that considered for nuclear application. In addition to materials aspects, results of programs focusing on practical aspects of deploying composites for near-term reactors will be discussed. In particular, significant progress has been made in the fabrication, testing, and qualification of composite gas-cooled reactor control rod sheaths and the ASTM standardization required for eventual qualification. (authors)

Neutron tolerance of advanced SiC-fiber/CVI-SiC composites

International Nuclear Information System (INIS)

Katoh, Y.; Kohyama, A.; Snead, L.L.; Hinoki, T.; Hasegawa, A.

2003-01-01

Fusion blankets employing a silicon carbide (SiC) fiber-reinforced SiC matrix composite (SiC/SiC composite) as the structural material provide attractive features represented by high cycle efficiency and extremely low induced radioactivity. Recent advancement in processing and utilization techniques and application studies in ceramic gas turbine and advanced transportation systems, SiC/SiC composites are steadily getting matured as industrial materials. Reference SiC/SiC composites for fusion structural applications have been produced by a forced-flow chemical vapor infiltration (FCVI) method using conventional and advanced near-stoichiometric SiC fibers and extensively evaluated primarily in Japan-US collaborative JUPITER program. In this work, effect of neutron irradiation at elevated temperatures on mechanical property of these composites is characterized. Unlike in conventional SiC/SiC composites, practically no property degradation was identified in advanced composites with a thin carbon interphase by a neutron fluence level of approximately 8dpa at 800C. (author)

The stress analysis method for three-dimensional composite materials

Science.gov (United States)

Nagai, Kanehiro; Yokoyama, Atsushi; Maekawa, Zen'ichiro; Hamada, Hiroyuki

1994-05-01

This study proposes a stress analysis method for three-dimensionally fiber reinforced composite materials. In this method, the rule-of mixture for composites is successfully applied to 3-D space in which material properties would change 3-dimensionally. The fundamental formulas for Young's modulus, shear modulus, and Poisson's ratio are derived. Also, we discuss a strength estimation and an optimum material design technique for 3-D composite materials. The analysis is executed for a triaxial orthogonally woven fabric, and their results are compared to the experimental data in order to verify the accuracy of this method. The present methodology can be easily understood with basic material mechanics and elementary mathematics, so it enables us to write a computer program of this theory without difficulty. Furthermore, this method can be applied to various types of 3-D composites because of its general-purpose characteristics.

On the linear programming bound for linear Lee codes.

Science.gov (United States)

Astola, Helena; Tabus, Ioan

2016-01-01

Based on an invariance-type property of the Lee-compositions of a linear Lee code, additional equality constraints can be introduced to the linear programming problem of linear Lee codes. In this paper, we formulate this property in terms of an action of the multiplicative group of the field [Formula: see text] on the set of Lee-compositions. We show some useful properties of certain sums of Lee-numbers, which are the eigenvalues of the Lee association scheme, appearing in the linear programming problem of linear Lee codes. Using the additional equality constraints, we formulate the linear programming problem of linear Lee codes in a very compact form, leading to a fast execution, which allows to efficiently compute the bounds for large parameter values of the linear codes.

Direct 4D printing via active composite materials

Science.gov (United States)

Ding, Zhen; Yuan, Chao; Peng, Xirui; Wang, Tiejun; Qi, H. Jerry; Dunn, Martin L.

2017-01-01

We describe an approach to print composite polymers in high-resolution three-dimensional (3D) architectures that can be rapidly transformed to a new permanent configuration directly by heating. The permanent shape of a component results from the programmed time evolution of the printed shape upon heating via the design of the architecture and process parameters of a composite consisting of a glassy shape memory polymer and an elastomer that is programmed with a built-in compressive strain during photopolymerization. Upon heating, the shape memory polymer softens, releases the constraint on the strained elastomer, and allows the object to transform into a new permanent shape, which can then be reprogrammed into multiple subsequent shapes. Our key advance, the markedly simplified creation of high-resolution complex 3D reprogrammable structures, promises to enable myriad applications across domains, including medical technology, aerospace, and consumer products, and even suggests a new paradigm in product design, where components are simultaneously designed to inhabit multiple configurations during service. PMID:28439560

Direct 4D printing via active composite materials.

Science.gov (United States)

Ding, Zhen; Yuan, Chao; Peng, Xirui; Wang, Tiejun; Qi, H Jerry; Dunn, Martin L

2017-04-01

We describe an approach to print composite polymers in high-resolution three-dimensional (3D) architectures that can be rapidly transformed to a new permanent configuration directly by heating. The permanent shape of a component results from the programmed time evolution of the printed shape upon heating via the design of the architecture and process parameters of a composite consisting of a glassy shape memory polymer and an elastomer that is programmed with a built-in compressive strain during photopolymerization. Upon heating, the shape memory polymer softens, releases the constraint on the strained elastomer, and allows the object to transform into a new permanent shape, which can then be reprogrammed into multiple subsequent shapes. Our key advance, the markedly simplified creation of high-resolution complex 3D reprogrammable structures, promises to enable myriad applications across domains, including medical technology, aerospace, and consumer products, and even suggests a new paradigm in product design, where components are simultaneously designed to inhabit multiple configurations during service.

Comparison of Requirements for Composite Structures for Aircraft and Space Applications

Science.gov (United States)

Raju, Ivatury S.; Elliot, Kenny B.; Hampton, Roy W.; Knight, Norman F., Jr.; Aggarwal, Pravin; Engelstad, Stephen P.; Chang, James B.

2010-01-01

In this report, the aircraft and space vehicle requirements for composite structures are compared. It is a valuable exercise to study composite structural design approaches used in the airframe industry and to adopt methodology that is applicable for space vehicles. The missions, environments, analysis methods, analysis validation approaches, testing programs, build quantities, inspection, and maintenance procedures used by the airframe industry, in general, are not transferable to spaceflight hardware. Therefore, while the application of composite design approaches from aircraft and other industries is appealing, many aspects cannot be directly utilized. Nevertheless, experiences and research for composite aircraft structures may be of use in unexpected arenas as space exploration technology develops, and so continued technology exchanges are encouraged.

Critical joints in large composite primary aircraft structures. Volume 2: Technology demonstration test report

Science.gov (United States)

Bunin, Bruce L.

1985-01-01

A program was conducted to develop the technology for critical structural joints in composite wing structure that meets all the design requirements of a 1990 commercial transport aircraft. The results of four large composite multirow bolted joint tests are presented. The tests were conducted to demonstrate the technology for critical joints in highly loaded composite structure and to verify the analytical methods that were developed throughout the program. The test consisted of a wing skin-stringer transition specimen representing a stringer runout and skin splice on the wing lower surface at the side of the fuselage attachment. All tests were static tension tests. The composite material was Toray T-300 fiber with Ciba-Geigy 914 resin in 10 mil tape form. The splice members were metallic, using combinations of aluminum and titanium. Discussions are given of the test article, instrumentation, test setup, test procedures, and test results for each of the four specimens. Some of the analytical predictions are also included.

Flight service evaluation of composite helicopter components

Science.gov (United States)

Mardoian, George H.; Ezzo, Maureen B.

1994-01-01

This paper presents the results of a NASA funded contract and Sikorsky research and development programs to evaluate structural composite components in flight service on Sikorsky Model S-76 helicopters. Selected components were removed and tested at prescribed intervals over a nine year time frame. Four horizontal stabilizers and thirteen tail rotor spars were returned from commercial service in West Palm Beach, Florida and in the Gulf Coast region of Louisiana to determine the long term effects of operations in hot and humid climates on component performance. Concurrent with the flight component evaluation, panels of materials used in their fabrication were exposed to the environment in ground racks. Selected panels were tested annually to determine the effects of exposure on physical and mechanical properties. The results of 55,741 component flight hours and 911 months of field exposure are reported and compared with initial Federal Aviation Administration (FAA) certification data. The findings of this program have provided increased confidence in the long term durability of advanced composite materials used in helicopter structural applications.

Stochastic-Strength-Based Damage Simulation Tool for Ceramic Matrix and Polymer Matrix Composite Structures

Science.gov (United States)

Nemeth, Noel N.; Bednarcyk, Brett A.; Pineda, Evan J.; Walton, Owen J.; Arnold, Steven M.

2016-01-01

Stochastic-based, discrete-event progressive damage simulations of ceramic-matrix composite and polymer matrix composite material structures have been enabled through the development of a unique multiscale modeling tool. This effort involves coupling three independently developed software programs: (1) the Micromechanics Analysis Code with Generalized Method of Cells (MAC/GMC), (2) the Ceramics Analysis and Reliability Evaluation of Structures Life Prediction Program (CARES/ Life), and (3) the Abaqus finite element analysis (FEA) program. MAC/GMC contributes multiscale modeling capabilities and micromechanics relations to determine stresses and deformations at the microscale of the composite material repeating unit cell (RUC). CARES/Life contributes statistical multiaxial failure criteria that can be applied to the individual brittle-material constituents of the RUC. Abaqus is used at the global scale to model the overall composite structure. An Abaqus user-defined material (UMAT) interface, referred to here as "FEAMAC/CARES," was developed that enables MAC/GMC and CARES/Life to operate seamlessly with the Abaqus FEA code. For each FEAMAC/CARES simulation trial, the stochastic nature of brittle material strength results in random, discrete damage events, which incrementally progress and lead to ultimate structural failure. This report describes the FEAMAC/CARES methodology and discusses examples that illustrate the performance of the tool. A comprehensive example problem, simulating the progressive damage of laminated ceramic matrix composites under various off-axis loading conditions and including a double notched tensile specimen geometry, is described in a separate report.

Thermoviscoelastic characterization and prediction of Kevlar/epoxy composite laminates

Science.gov (United States)

Gramoll, K. C.; Dillard, D. A.; Brinson, H. F.

1990-01-01

The thermoviscoelastic characterization of Kevlar 49/Fiberite 7714A epoxy composite lamina and the development of a numerical procedure to predict the viscoelastic response of any general laminate constructed from the same material were studied. The four orthotropic material properties, S sub 11, S sub 12, S sub 22, and S sub 66, were characterized by 20 minute static creep tests on unidirectional (0) sub 8, (10) sub 8, and (90) sub 16 lamina specimens. The Time-Temperature Superposition-Principle (TTSP) was used successfully to accelerate the characterization process. A nonlinear constitutive model was developed to describe the stress dependent viscoelastic response for each of the material properties. A numerical procedure to predict long term laminate properties from lamina properties (obtained experimentally) was developed. Numerical instabilities and time constraints associated with viscoelastic numerical techniques were discussed and solved. The numerical procedure was incorporated into a user friendly microcomputer program called Viscoelastic Composite Analysis Program (VCAP), which is available for IBM PC type computers. The program was designed for ease of use. The final phase involved testing actual laminates constructed from the characterized material, Kevlar/epoxy, at various temperatures and load level for 4 to 5 weeks. These results were compared with the VCAP program predictions to verify the testing procedure and to check the numerical procedure used in the program. The actual tests and predictions agreed for all test cases which included 1, 2, 3, and 4 fiber direction laminates.

Design of an Advanced Wood Composite Rotor and Development of Wood Composite Blade Technology

Science.gov (United States)

Stroebel, Thomas; Dechow, Curtis; Zuteck, Michael

1984-01-01

In support of a program to advance wood composite wind turbine blade technology, a design was completed for a prototype, 90-foot diameter, two-bladed, one-piece rotor, with all wood/epoxy composite structure. The rotor was sized for compatibility with a generator having a maximum power rating of 4000 kilowatts. Innovative features of the rotor include: a teetering hub to minimize the effects of gust loads, untwisted blades to promote rotor power control through stall, joining of blades to the hub structure via an adhesive bonded structural joint, and a blade structural design which was simplified relative to earlier efforts. The prototype rotor was designed to allow flexibility for configuring the rotor upwind or downwind of the tower, for evaluating various types of teeter dampers and/or elastomeric stops, and with variable delta-three angle settings of the teeter shaft axis. The prototype rotor was also designed with provisions for installing pressure tap and angle of attack instrumentation in one blade. A production version rotor cost analysis was conducted. Included in the program were efforts directed at developing advanced load take-off stud designs for subsequent evaluation testing by NASA, development of aerodynamic tip brake concepts, exploratory testing of a wood/epoxy/graphite concept, and compression testing of wood/epoxy laminate, with scarf-jointed plies.

Changes in weight loss, body composition and cardiovascular disease risk after altering macronutrient distributions during a regular exercise program in obese women

Directory of Open Access Journals (Sweden)

Roberts Mike D

2010-11-01

Full Text Available Abstract Background This study's purpose investigated the impact of different macronutrient distributions and varying caloric intakes along with regular exercise for metabolic and physiological changes related to weight loss. Methods One hundred forty-one sedentary, obese women (38.7 ± 8.0 yrs, 163.3 ± 6.9 cm, 93.2 ± 16.5 kg, 35.0 ± 6.2 kg•m-2, 44.8 ± 4.2% fat were randomized to either no diet + no exercise control group (CON a no diet + exercise control (ND, or one of four diet + exercise groups (high-energy diet [HED], very low carbohydrate, high protein diet [VLCHP], low carbohydrate, moderate protein diet [LCMP] and high carbohydrate, low protein [HCLP] in addition to beginning a 3x•week-1 supervised resistance training program. After 0, 1, 10 and 14 weeks, all participants completed testing sessions which included anthropometric, body composition, energy expenditure, fasting blood samples, aerobic and muscular fitness assessments. Data were analyzed using repeated measures ANOVA with an alpha of 0.05 with LSD post-hoc analysis when appropriate. Results All dieting groups exhibited adequate compliance to their prescribed diet regimen as energy and macronutrient amounts and distributions were close to prescribed amounts. Those groups that followed a diet and exercise program reported significantly greater anthropometric (waist circumference and body mass and body composition via DXA (fat mass and % fat changes. Caloric restriction initially reduced energy expenditure, but successfully returned to baseline values after 10 weeks of dieting and exercising. Significant fitness improvements (aerobic capacity and maximal strength occurred in all exercising groups. No significant changes occurred in lipid panel constituents, but serum insulin and HOMA-IR values decreased in the VLCHP group. Significant reductions in serum leptin occurred in all caloric restriction + exercise groups after 14 weeks, which were unchanged in other non

Carbon Fiber Composite Materials for Automotive Applications

Energy Technology Data Exchange (ETDEWEB)

Norris, Jr., Robert E. [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States); Mainka, Hendrik [Oak Ridge National Lab. (ORNL), Oak Ridge, TN (United States)

2017-06-01

Volkswagen (VW) is internationally recognized for quantity and quality of world-wide vehicle production and the Oak Ridge National Laboratory (ORNL) is internationally recognized in materials research and development. With automotive production ramping up in the recently constructed VW Group of America facility in Chattanooga, Tennessee, ORNL and VW initiated discussions in 2012 concerning opportunities for collaboration around ORNL’s carbon fiber and composites programs. ORNL is conducting an internationally recognized program to develop and implement lower cost carbon fibers and composites for automotive and other “energy missions” for the US Department of Energy. Significant effort is ongoing in selecting, developing, and evaluating alternative precursors, developing and demonstrating advanced conversion techniques, and developing and tailoring surface treatment, sizings, and formatting fiber for specific composite matrices and end-use applications. ORNL already had North America’s most comprehensive suite of tools for carbon fiber research and development and established a semiproduction demonstration line referred to as the Carbon Fiber Technology Facility (CFTF) to facilitate implementation of low cost carbon fiber (LCCF) approaches in early 2013. ORNL and VW agreed to collaborate in a formal Cooperative Research and Development Agreement (NFE-12-03992) specifically focused on evaluating applicability of low cost carbon fiber products for potential vehicle components. The goal of the work outlined in this report was to develop and qualify uses for carbon fiber-reinforced structures in connection with civilian ground transportation. Significant progress was achieved in evaluating and understanding lignin-based precursor materials; however, availability of carbon fiber converted from lignin precursor combined with logistical issues associated with the Visa limitations for the VW participant resulted in significantly shortening of the collaboration

LH2 Tank Composite Coverplate Development and Flight Qualification for the X-33

Science.gov (United States)

Wright, Richard J.; Roule, Gerard M.

2000-01-01

In this paper, the development history for the first cryogenic pressurized fuel tank coverplates is presented along with a synopsis of the development strategy and technologies which led to success on this program. Coverplates are the large access panels used to access launch vehicle fuel tanks. These structures incorporate all of the requirements for a pressure vessel as well as the added requirement to mount all of the miscellaneous access points required for a fuel management system. The first composite coverplates to meet the requirements for flight qualification were developed on the X-33 program. The X-33 composite coverplates went from an open requirement to successful finished flight hardware with multiple unique configurations, complete with verification testing, in less than eighteen months. Besides the rapid development schedule, these components introduced several new technologies previously unseen in cryogenic composites including solutions to cryogenic shrinkage, self-supporting sealing surfaces, and highly loaded composite bosses with precision sealing interfaces. These components were proven to seal liquid hydrogen at cryogenic temperatures under maximum loading and pressure conditions.

Ceramic Composite Intermediate Temperature Stress-Rupture Properties Improved Significantly

Science.gov (United States)

Morscher, Gregory N.; Hurst, Janet B.

2002-01-01

Silicon carbide (SiC) composites are considered to be potential materials for future aircraft engine parts such as combustor liners. It is envisioned that on the hot side (inner surface) of the combustor liner, composites will have to withstand temperatures in excess of 1200 C for thousands of hours in oxidizing environments. This is a severe condition; however, an equally severe, if not more detrimental, condition exists on the cold side (outer surface) of the combustor liner. Here, the temperatures are expected to be on the order of 800 to 1000 C under high tensile stress because of thermal gradients and attachment of the combustor liner to the engine frame (the hot side will be under compressive stress, a less severe stress-state for ceramics). Since these composites are not oxides, they oxidize. The worst form of oxidation for strength reduction occurs at these intermediate temperatures, where the boron nitride (BN) interphase oxidizes first, which causes the formation of a glass layer that strongly bonds the fibers to the matrix. When the fibers strongly bond to the matrix or to one another, the composite loses toughness and strength and becomes brittle. To increase the intermediate temperature stress-rupture properties, researchers must modify the BN interphase. With the support of the Ultra-Efficient Engine Technology (UEET) Program, significant improvements were made as state-of-the-art SiC/SiC composites were developed during the Enabling Propulsion Materials (EPM) program. Three approaches were found to improve the intermediate-temperature stress-rupture properties: fiber-spreading, high-temperature silicon- (Si) doped boron nitride (BN), and outside-debonding BN.

A Program in Social Sciences for Engineering Students.

Science.gov (United States)

Kumar, K. S. P.

A set of programs in liberal education designed to enhance the social dimensions of engineering education is described. This program requires a minimum of 36 quarter credits in the broad categories of English Composition (8-10 credits), Man and Society (12-15 credits), Artistic Expression (8-10 credits), and the balance from any of the above…

Effect of 4 weeks of Pilates on the body composition of young girls

NARCIS (Netherlands)

Jago, R; Jonker, ML; Missaghian, M; Baranowski, T

Background. There is a need to find ways to increase the physical activity levels and improve the body composition and blood pressure of girls. Methods. Thirty 11-year-old girls were recruited from two after school programs in Houston Texas in Spring 2005. Participants from one program (16) were

Composites

International Nuclear Information System (INIS)

Kasen, M.B.

1983-01-01

This chapter discusses the roles of composite laminates and aggregates in cryogenic technology. Filamentary-reinforced composites are emphasized because they are the most widely used composite materials. Topics considered include composite systems and terminology, design and fabrication, composite failure, high-pressure reinforced plastic laminates, low-pressure reinforced plastics, reinforced metals, selectively reinforced structures, the effect of cryogenic temperatures, woven-fabric and random-mat composites, uniaxial fiber-reinforced composites, composite joints in cryogenic structures, joining techniques at room temperature, radiation effects, testing laminates at cryogenic temperatures, static and cyclic tensile testing, static and cyclic compression testing, interlaminar shear testing, secondary property tests, and concrete aggregates. It is suggested that cryogenic composite technology would benefit from the development of a fracture mechanics model for predicting the fitness-for-purpose of polymer-matrix composite structures

Predictions of the product compositions for combustion or gasification of biomass and others hydrocarbons

Energy Technology Data Exchange (ETDEWEB)

Rocha, Hendrick Maxil Zarate; Itai, Yuu; Nogueira, Manoel Fernandes Martins; Moraes, Sinfronio Brito; Rocha, Brigida Ramati Pereira da [Universidade Federal do Para (UFPA), Belem, PA (Brazil). Faculdade de Engenharia Mecanica]. E-mails: hendrick@ufpa.br; yuuitai@ufpa.br; mfmn@ufpa.br; sbrito@ufpa.br; brigida@ufpa.br

2008-07-01

Processes involving combustion and gasification are object of study of many researchers. To simulate these processes in a detailed way, it is necessary to solve equations for chemical kinetics whose resolution many times is difficult due lack of information in the literature a simples way to bypass tis problem is due the chemical equilibrium. Prediction of the flu gases composition through chemical equilibrium is an important step in the mathematical modelling for gasification and combustion processes. Some free programs exists to solve problems that involve the chemical equilibrium, such as STANJAN, CEA, GASEQ, CANTERA and others.These programs have difficulty for cases involving fuel such as: biomass, vegetable oils, biodiesel, natural gas, etc., because they do not have database with the fuel composition and is hard to supply their HHV and their elementary analysis. In this work, using numeric methods, a program was developed to predict the gases composition on equilibrium after combustion and gasification processes with the for constant pressure or volume. In the program the chemical formula of the fuel is defined as C{sub x}H{sub y}O{sub z}N{sub w}S{sub v}A{sub u} that reacts with an gaseous oxidizer composed by O{sub 2}, N{sub 2}, Ar, He, CO{sub 2} e H{sub 2}O to have as final result the composition of the products CO{sub 2}, CO, H{sub 2}O, H{sub 2}, H, OH, O{sub 2}, O, N{sub 2}, NO, SO{sub 2}, CH{sub 4}, Ar, He, and ash. To verify the accuracy of the calculated values, it was compared with the program CEA (developed by NASA) and with experimental data obtained from literature. (author)

Beyond the GRE: using a composite score to predict 
the success of Puerto Rican students in a biomedical 
PhD program.

Science.gov (United States)

Pacheco, Wendy I; Noel, Richard J; Porter, James T; Appleyard, Caroline B

2015-01-01

The use and validity of the Graduate Record Examination General Test (GRE) to predict the success of graduate school applicants is heavily debated, especially for its possible impact on the selection of underrepresented minorities into science, technology, engineering, and math fields. To better identify candidates who would succeed in our program with less reliance on the GRE and grade point average (GPA), we developed and tested a composite score (CS) that incorporates additional measurable predictors of success to evaluate incoming applicants. Uniform numerical values were assigned to GPA, GRE, research experience, advanced course work or degrees, presentations, and publications. We compared the CS of our students with their achievement of program goals and graduate school outcomes. The average CS was significantly higher in those students completing the graduate program versus dropouts (p thesis defense. In contrast, these outcomes were not predicted by GPA, science GPA, or GRE. Recent implementation of an impromptu writing assessment during the interview suggests the CS can be improved further. We conclude that the CS provides a broader quantitative measure that better predicts success of students in our program and allows improved evaluation and selection of the most promising candidates. © 2015 W. I. Pacheco et al. CBE—Life Sciences Education © 2015 The American Society for Cell Biology. This article is distributed by The American Society for Cell Biology under license from the author(s). It is available to the public under an Attribution–Noncommercial–Share Alike 3.0 Unported Creative Commons License (http://creativecommons.org/licenses/by-nc-sa/3.0).

Design, Fabrication, and Testing of a Composite Rack Prototype in Support of the Deep Space Habitat Program

Science.gov (United States)

Smith, Russ; Hagen, Richard

2015-01-01

In support of the Deep Space Habitat project a number of composite rack prototypes were developed, designed, fabricated and tested to various extents ( with the International Standard Payload Rack configuration, or crew quarters, as a baseline). This paper focuses specifically on a composite rack prototype with a direct tie in to Space Station hardware. The outlined prototype is an all composite construction, excluding metallic fasteners, washers, and their associated inserts. The rack utilizes braided carbon composite tubing for the frame with the sidewalls, backwall and flooring sections utilizing aircraft grade composite honeycomb sandwich panels. Novel additively manufactured thermoplastic joints and tube inserts were also developed in support of this effort. Joint and tube insert screening tests were conducted at a preliminary level. The screening tests allowed for modification, and enhancement, of the fabrication and design approaches, which will be outlined. The initial joint tests did not include mechanical fasteners. Adhesives were utilized at the joint to composite tube interfaces, along with mechanical fasteners during final fabrication (thus creating a stronger joint than the adhesive only variant). In general the prototype was focused on a potential in-space assembly approach, or kit-of-parts construction concept, which would not necessarily require the inclusion of an adhesive in the joint regions. However, given the tie in to legacy Station hardware (and potential flight loads with imbedded hardware mass loadings), the rack was built as stiff and strong as possible. Preliminary torque down tests were also conducted to determine the feasibility of mounting the composite honeycomb panels to the composite tubing sections via the additively manufactured tube inserts. Additional fastener torque down tests were also conducted with inserts (helicoils) imbedded within the joints. Lessons learned are also included and discussed.

Addendum to: Derivation of in situ opalinus clay porewater compositions from experimental and geochemical modelling studies

International Nuclear Information System (INIS)

Bradbury, M.H.; Baeyens; Pearson, F.J.; Berner, U.

1998-01-01

As part of the synthesis of water chemistry studies within the hydrochemical program at Mont Terri (Switzerland), a reexamination of the modelling method showed that it should lead to a range of water compositions rather than to a single composition. The single composition resulted from two compensating oversights, a theoretical one and a modelling one. These are discussed in this Addendum. (author)

Non-linear programming method in optimization of fast reactors

International Nuclear Information System (INIS)

Pavelesku, M.; Dumitresku, Kh.; Adam, S.

1975-01-01

Application of the non-linear programming methods on optimization of nuclear materials distribution in fast reactor is discussed. The programming task composition is made on the basis of the reactor calculation dependent on the fuel distribution strategy. As an illustration of this method application the solution of simple example is given. Solution of the non-linear program is done on the basis of the numerical method SUMT. (I.T.)

The Lewis Chemical Equilibrium Program with parametric study capability

Science.gov (United States)

Sevigny, R.

1981-01-01

The program was developed to determine chemical equilibrium in complex systems. Using a free energy minimization technique, the program permits calculations such as: chemical equilibrium for assigned thermodynamic states; theoretical rocket performance for both equilibrium and frozen compositions during expansion; incident and reflected shock properties; and Chapman-Jouget detonation properties. It is shown that the same program can handle solid coal in an entrained flow coal gasification problem.

EFFECTS OF PHYSICAL ACTIVITY ON BODY COMPOSITION IN ADULT WOMEN

Directory of Open Access Journals (Sweden)

Klára NAGY

2017-06-01

Full Text Available Data published by the World Health Organization (WHO and the International Association for the Study of Obesity (IASO suggests that the number of obese people in Europe has tripled in the last 20 years and resulted in a prevalence of 130 million obese and 400 million people overweight (Sassi et al., 2009.Body composition is the relative percentage of fat and fat-free mass (bones, muscles, organs, water, blood of total body weight. After Wilmore, Buskirk, DiGirolamo and Lohman (1986 the optimal level for health of body fat is 16-25% (18-30% for women.The objective of our study was to assess body composition of adult women, identifying the effect of intervention program on body fat and lean mass, and uncover cases of obesity and overweight.The study involved 95 adult women from Fit4U Fitness Center in Oradea. Period of the study: February 2015 -June 2016. Anthropometric measurements were made: height, weight, circumference, subcutaneous folds. It was calculated the body mass index (BMI, body composition and optimal body weight (estimation based on the five skinfolds measures. The physical activity program consisted of Step -aerobics, Pilates and strength training in the gym, 3 times a week for 60-90 minutes, for 12 months.Results:mean body mass, BMI, BF%, real BF decreased significantly. Mean body fat percentage from 25,63% (± 6,53 decreased to 22,95% (± 5,56. In the studied group overweight and obesity is more frequent in the age group between 35-44 years, but it can be seen the prevalence in all age groups.Conclusions:the physical activity program had a beneficial effect on body composition -by reducing body fat.We found cases of overweight and obesity (21% of the study group.

The Composition of the Master Schedule

Science.gov (United States)

Thomas, Cynthia C.; Behrend, Dirk; MacMillan, Daniel S.

2010-01-01

Over a period of about four months, the IVS Coordinating Center (IVSCC) each year composes the Master Schedule for the IVS observing program of the next calendar year. The process begins in early July when the IVSCC contacts the IVS Network Stations to request information about available station time as well as holiday and maintenance schedules for the upcoming year. Going through various planning stages and a review process with the IVS Observing Program Committee (OPC), the final version of the Master Schedule is posted by early November. We describe the general steps of the composition and illustrate them with the example of the planning for the Master Schedule of the 2010 observing year.

Optimization of composite sandwich cover panels subjected to compressive loadings

Science.gov (United States)

Cruz, Juan R.

1991-01-01

An analysis and design method is presented for the design of composite sandwich cover panels that include the transverse shear effects and damage tolerance considerations. This method is incorporated into a sandwich optimization computer program entitled SANDOP. As a demonstration of its capabilities, SANDOP is used in the present study to design optimized composite sandwich cover panels for for transport aircraft wing applications. The results of this design study indicate that optimized composite sandwich cover panels have approximately the same structural efficiency as stiffened composite cover panels designed to satisfy individual constraints. The results also indicate that inplane stiffness requirements have a large effect on the weight of these composite sandwich cover panels at higher load levels. Increasing the maximum allowable strain and the upper percentage limit of the 0 degree and +/- 45 degree plies can yield significant weight savings. The results show that the structural efficiency of these optimized composite sandwich cover panels is relatively insensitive to changes in core density. Thus, core density should be chosen by criteria other than minimum weight (e.g., damage tolerance, ease of manufacture, etc.).

Composition of web services using Markov decision processes and dynamic programming.

Science.gov (United States)

Uc-Cetina, Víctor; Moo-Mena, Francisco; Hernandez-Ucan, Rafael

2015-01-01

We propose a Markov decision process model for solving the Web service composition (WSC) problem. Iterative policy evaluation, value iteration, and policy iteration algorithms are used to experimentally validate our approach, with artificial and real data. The experimental results show the reliability of the model and the methods employed, with policy iteration being the best one in terms of the minimum number of iterations needed to estimate an optimal policy, with the highest Quality of Service attributes. Our experimental work shows how the solution of a WSC problem involving a set of 100,000 individual Web services and where a valid composition requiring the selection of 1,000 services from the available set can be computed in the worst case in less than 200 seconds, using an Intel Core i5 computer with 6 GB RAM. Moreover, a real WSC problem involving only 7 individual Web services requires less than 0.08 seconds, using the same computational power. Finally, a comparison with two popular reinforcement learning algorithms, sarsa and Q-learning, shows that these algorithms require one or two orders of magnitude and more time than policy iteration, iterative policy evaluation, and value iteration to handle WSC problems of the same complexity.

Foundations of compositional models: structural properties

Czech Academy of Sciences Publication Activity Database

Jiroušek, Radim; Kratochvíl, Václav

2015-01-01

Roč. 44, č. 1 (2015), s. 2-25 ISSN 0308-1079 R&D Projects: GA ČR GA13-20012S Grant - others:GA ČR(CZ) GAP403/12/2175 Program:GA Institutional support: RVO:67985556 Keywords : multidimensional distribution * conditional independence * composition * semigraphoid properties * running intersection property Subject RIV: BA - General Mathematics Impact factor: 1.677, year: 2015 http://library.utia.cas.cz/separaty/2015/MTR/jirousek-0442412.pdf

Critical Joints in Large Composite Primary Aircraft Structures. Volume 3: Ancillary Test Results

Science.gov (United States)

Bunin, Bruce L.; Sagui, R. L.

1985-01-01

A program was conducted to develop the technology for critical structural joints for composite wing structure that meets all the design requirements of a 1990 commercial transport aircraft. The results of a comprehensive ancillary test program are summarized, consisting of single-bolt composite joint specimens tested in a variety of configurations. These tests were conducted to characterize the strength and load deflection properties that are required for multirow joint analysis. The composite material was Toray 300 fiber and Ciba-Geigy 914 resin, in the form of 0.005 and 0.01 inch thick unidirectional tape. Tests were conducted in single and double shear for loaded and unloaded hole configurations under both tensile and compressive loading. Two different layup patterns were examined. All tests were conducted at room temperature. In addition, the results of NASA Standard Toughness Test (NASA RP 1092) are reported, which were conducted for several material systems.

Regional food dishes in the Brazilian National School Food Program: Acceptability and nutritional composition

Directory of Open Access Journals (Sweden)

Diogo thimoteo da Cunha

2014-08-01

Full Text Available Objective: the objective of this study was to evaluate the nutritional composition and describe the acceptability of regional culinary dishes served to students from public schools of rural and urban areas. Methods: Ten Brazilian regional dishes were evaluated for acceptability and nutritional composition. the survey was conducted in schools located in rural and urban areas of two cities in the state of São Paulo. Dish acceptability was evaluated using leftover analysis and a 5-point facial hedonic scale. the adherence index was calculated and used as an indirect measure of acceptance, and the nutritional composition was calculated based on the technical files of each dish. Results: A total of 2,384 students from 20 schools participated in the study and 1,174 tasted and evaluated the dishes. the test using the 5-point facial hedonic scale demonstrated that five dishes (Caldo verde soup, persimmon jelly, chicken with okra, puréed cornmeal with spinach, and arugula pizza had an acceptability rate above 85.0%. the mean adherence indices were 57.3% and 55.6% in urban and rural environments, respectively. Analysis of the nutritional composition of regional dishes indicates that these dishes can partially meet macronutrient recommendations. Conclusion: the tested dishes can become part of school menus as they were accepted or partly accepted by the students regardless of school location, whether rural or urban. the cultural heritage is an important resource for the food sovereignty of a country and should be constantly encouraged.

Recent NASA progress in composites. [application to spacecraft and aircraft structures

Science.gov (United States)

Heldenfels, R. R.

1975-01-01

The application of composites in aerospace vehicle structures is reviewed. Research and technology program results and specific applications to space vehicles, aircraft engines, and aircraft and helicopter structures are discussed in detail. Particular emphasis is given to flight service evaluation programs that are or will be accumulating substantial experience with secondary and primary structural components on military and commercial aircraft to increase confidence in their use.

Synthesis and processing of composites by reactive metal penetration

Energy Technology Data Exchange (ETDEWEB)

Loehman, R.E.; Ewsuk, K.G. [Sandia National Labs., Albuquerque, NM (United States); Tomsia, A.P. [Pask Research and Engineering, Berkeley, CA (United States)] [and others

1997-04-01

Achieving better performance in commercial products and processes often is dependent on availability of new and improved materials. Ceramic-metal composites have advantages over more conventional materials because of their high stiffness-to-weight ratios, good fracture toughness, and because their electrical and thermal properties can be varied through control of their compositions and microstructures. However, ceramic composites will be more widely used only when their costs are competitive with other materials and when designers have more confidence in their reliability. Over the past four years reactive metal penetration has been shown to be a promising technique for making ceramic and metal-matrix composites to near-net-shape with control of both composition and microstructure. It appears that, with sufficient development, reactive metal penetration could be an economical process for manufacturing many of the advanced ceramic composites that are needed for light-weight structural and wear applications for transportation and energy conversion devices. Near-net-shape fabrication of parts is a significant advantage because costly and energy intensive grinding and machining operations are substantially reduced, and the waste generated from such finishing operations is minimized. The most promising compositions to date consist of Al and Al{sub 2}O{sub 3}; thus, these composites should be of particular interest to the aluminum industry. The goals of this ceramic-metal composite research and development program are: (1) to identify compositions favorable for making composites by reactive metal penetration; (2) to understand the mechanism(s) by which these composites are formed; (3) to control and optimize the process so that composites and composite coatings can be made economically; and (4) to apply R&D results to problems of interest to the aluminum industry.

An ALARA-conscious hot particle control program

International Nuclear Information System (INIS)

Doolittle, W.W.; Bredvad, R.S.; Bevelacqua, J.J.

1992-01-01

In 1989 approximately twenty-five percent of the radiation dose received by the Point Beach Nuclear Plant (PBNP) Health Physics group was due to its hot particle control program. The Health Physics group initiated a review of the program with the objective of decreasing the dose expenditure for hot particle control while maintaining a high standard for hot particle detection and control. In this paper the methods and results of this evaluation are described. The components of the hot particle control program, rules of thumb, and radionuclide composition at PBNP are presented

Static Mapping of Functional Programs: An Example in Signal Processing

Directory of Open Access Journals (Sweden)

Jack B. Dennis

1996-01-01

Full Text Available Complex signal-processing problems are naturally described by compositions of program modules that process streams of data. In this article we discuss how such compositions may be analyzed and mapped onto multiprocessor computers to effectively exploit the massive parallelism of these applications. The methods are illustrated with an example of signal processing for an optical surveillance problem. Program transformation and analysis are used to construct a program description tree that represents the given computation as an acyclic interconnection of stream-processing modules. Each module may be mapped to a set of threads run on a group of processing elements of a target multiprocessor. Performance is considered for two forms of multiprocessor architecture, one based on conventional DSP technology and the other on a multithreaded-processing element design.

The effect of composition on volatility from a copper alloy

International Nuclear Information System (INIS)

McCarthy, K.A.; Smolik, G.R.; Wallace, R.S.

1994-01-01

During a Loss of Coolant Accident (LOCA) activated structural material can be mobilized through oxidation. Information on how much material is mobilized in an accident is necessary for performing safety assessments of fusion reactor designs. The Fusion Safety Program at the Idaho National Engineering Laboratory has an experimental program to measure mobilized mass as a function of temperature for various oxidizing environments. Materials studied have included beryllium (important because of its toxicity), copper alloys, a niobium alloy, PCA and HT-9 steel, tungsten (pure and an alloy), and a vanadium alloy. Some materials undergo a significant change in composition during irradiation. An example of this is copper (a candidate for the ITER first wall, divertor substrate, and various instrumentation probes and antennas), which can have as much as 1 wt% zinc due to transmutation. Additionally, as the design for ITER evolves, a slightly different copper alloy may be selected. Compositional changes may affect the extent that various elements are volatilized due to such mechanisms as diffusion through the alloy, and penetration and release from oxide layers formed on the material. To accurately calculate offsite doses for various irradiation scenarios, one must understand the effect of composition on volatility

Effect of prenatal programming on heifer development.

Science.gov (United States)

Funston, Richard N; Summers, Adam F

2013-11-01

In beef cattle, the main factors influencing nutrient partitioning between the dam and fetus include age of the dam, number of fetuses, production demand, and environmental stress. These factors play a critical role in programming the fetus for its future environment and available resources. Fetal programming reportedly affects neonatal mortality and morbidity, postnatal growth rate, body composition, health, and reproduction. Two main mechanisms responsible for fetal programming include DNA methylation and histone modifications. Alterations in the genome can be passed through multiple generations. Maternal environment (nutrition, age, physiologic status) can program progeny heifer growth and reproductive performance. Copyright © 2013 Elsevier Inc. All rights reserved.

Ballistic performance of a Kevlar-29 woven fibre composite under varied temperatures

Science.gov (United States)

Soykasap, O.; Colakoglu, M.

2010-05-01

Armours are usually manufactured from polymer matrix composites and used for both military and non-military purposes in different seasons, climates, and regions. The mechanical properties of the composites depend on temperature, which also affects their ballistic characteristics. The armour is used to absorb the kinetic energy of a projectile without any major injury to a person. Therefore, besides a high strength and lightness, a high damping capacity is required to absorb the impact energy transferred by the projectile. The ballistic properties of a Kevlar 29/polyvinyl butyral composite are investigated under varied temperatures in this study. The elastic modulus of the composite is determined from the natural frequency of composite specimens at different temperatures by using a damping monitoring method. Then, the backside deformation of composite plates is analysed experimentally and numerically employing the finite-element program Abaqus. The experimental and numeric results obtained are in good agreement.

Engineered cementitious composites for strengthening masonry infilled reinforced concrete frames

DEFF Research Database (Denmark)

Dehghani, Ayoub; Nateghi-Alahi, Fariborz; Fischer, Gregor

2015-01-01

The results of the second part of a comprehensive experimental program, aimed at investigating the behavior of masonry infilled reinforced concrete (RC) frames strengthened with fiber reinforced engineered cementitious composites (ECC) used as an overlay on the masonry wall, are presented...

Ontario hydro's aqueous discharge monitoring program

International Nuclear Information System (INIS)

Mehdi, S.H.; Booth, M.R.; Massey, R.; Herrmann, O.

1992-01-01

The Province of Ontario has legislated a comprehensive monitoring program for waterborne trace contaminants called MISA - Municipal Industrial Strategy for Abatement. The electric power sector regulation applies to all generating stations (Thermal, Nuclear, Hydraulic). The program commenced in June, 1990. The current phase of the regulation requires the operators of the plants to measure the detailed composition of the direct discharges to water for a one year period. Samples are to be taken from about 350 identified streams at frequencies varying from continuous and daily to quarterly. The data from this program will be used to determine the scope of the ongoing monitoring program and control. This paper discusses the preparation and planning, commissioning, training and early operations phase of the MISA program. In response, the central Analytical Laboratory and Environmental staff worked to develop a sampling and analytical approach which uses the plant laboratories, the central analytical laboratory and a variety of external laboratories. The approach considered analytical frequency, sample stability, presence of radioactivity, suitability of staff, laboratory qualifications, need for long term internal capabilities, availability of equipment, difficulty of analysis, relationship to other work and problems, capital and operating costs. The complexity of the sampling program required the development of a computer based schedule to ensure that all required samples were taken as required with phase shifts between major sampling events at different plants to prevent swamping the capability of the central or external laboratories. New equipment has been purchased and installed at each plant to collect 24 hour composite samples. Analytical equipment has been purchased for each plant for analysis of perishable analytes or of samples requiring daily or thrice weekly analysis. Training programs and surveys have been implemented to assure production of valid data

Synthesizing Service Composition Models on the Basis of Temporal Business Rules

Institute of Scientific and Technical Information of China (English)

Jian Yu; Yan-Bo Han; Jun Han; Yan Jin; Paolo Falcarin; Maurizio Morisio

2008-01-01

Transformational approaches to generating design and implementation models from requirements can bring effectiveness and quality to software development. In this paper we present a framework and associated techniques to generate the process model of a service composition from a set of temporal business rules. Dedicated techniques including pathfinding, branching structure identification and parallel structure identification are used for semi-automatically synthesizing the process model from the semantics-equivalent Finite State Automata of the rules. These process models naturally satisfy the prescribed behavioral constraints of the rules. With the domain knowledge encoded in the temporal business rules,an executable service composition program, e.g., a BPEL program, can be further generated from the process models. A running example in the e-business domain is used for illustrating our approach throughout this paper.

Development of design data for graphite reinforced epoxy and polyimide composites

Science.gov (United States)

Scheck, W. G.

1974-01-01

Processing techniques and design data were characterized for a graphite/epoxy composite system that is useful from 75 K to 450 K, and a graphite/polyimide composite system that is useful from 75 K to 589 K. The Monsanto 710 polyimide resin was selected as the resin to be characterized and used with the graphite fiber reinforcement. Material was purchased using the prepreg specification for the design data generation for both the HT-S/710 and HM-S/710 graphite/polyimide composite system. Lamina and laminate properties were determined at 75 K, 297 K, and 589 K. The test results obtained on the skin-stringer components proved that graphite/polyimide composites can be reliably designed and analyzed much like graphite/epoxy composites. The design data generated in the program includes the standard static mechanical properties, biaxial strain data, creep, fatigue, aging, and thick laminate data.

Ceramic matrix composites -- Advanced high-temperature structural materials

International Nuclear Information System (INIS)

Lowden, R.A.; Ferber, M.K.; DiPietro, S.G.

1995-01-01

This symposium on Ceramic Matrix Composites: Advanced High-Temperature Structural Materials was held at the 1994 MRS Fall Meeting in Boston, Massachusetts on November 28--December 2. The symposium was sponsored by the Department of Energy's Office of Industrial Technology's Continuous Fiber Ceramic Composites Program, the Air Force Office of Scientific Research, and NASA Lewis Research Center. Among the competing materials for advanced, high-temperature applications, ceramic matrix composites are leading candidates. The symposium was organized such that papers concerning constituents--fibers and matrices--were presented first, followed by composite processing, modeling of mechanical behavior, and thermomechanical testing. More stable reinforcements are necessary to enhance the performance and life of fiber-reinforced ceramic composites, and to ensure final acceptance of these materials for high-temperature applications. Encouraging results in the areas of polymer-derived SiC fibers and single crystal oxide filaments were given, suggesting composites with improved thermomechanical properties and stability will be realized in the near future. The significance of the fiber-matrix interface in the design and performance of these materials is evident. Numerous mechanical models to relate interface properties to composite behavior, and interpret test methods and data, were enthusiastically discussed. One issue of great concern for any advanced material for use in extreme environments is stability. This theme arose frequently throughout the symposium and was the topic of focus on the final day. Fifty nine papers have been processed separately for inclusion on the data base

Proceedings of the Subcontractors' Review Meeting: Aquatic Species Program

Energy Technology Data Exchange (ETDEWEB)

1981-07-01

The Aquatic Species Program (ASP) addresses the utilization of plant biomass that naturally occurs in wetland or submerged areas. Processes are being developed through this program to make use of such aquatic species, capitalizing on their inherent capacity for rapid growth as well as their extraordinary chemical compositions.

GRUCAL, a computer program for calculating macroscopic group constants

International Nuclear Information System (INIS)

Woll, D.

1975-06-01

Nuclear reactor calculations require material- and composition-dependent, energy averaged nuclear data to describe the interaction of neutrons with individual isotopes in material compositions of reactor zones. The code GRUCAL calculates these macroscopic group constants for given compositions from the material-dependent data of the group constant library GRUBA. The instructions for calculating group constants are not fixed in the program, but will be read at the actual execution time from a separate instruction file. This allows to accomodate GRUCAL to various problems or different group constant concepts. (orig.) [de

Recommendations for composite manufacturing pultrusion process and equipment

Science.gov (United States)

Steiner, R. L.; Cole, J. D.; Strong, A. B.; Todd, R. H.

1992-10-01

Pultrusion is an important composite manufacturing process that holds great potential for reducing the cost of composite parts. However, pultrusion machine manufacturers and those using this continuous process have generally worked in relative isolation from each other and have, therefore, repeated many of the same errors. This paper reports the findings of a research program involving input from 15 pultruder manufacturers who have contributed non-proprietary information for the "best" design for the pultrusion machine. Key areas of design difficulty have been identified and some suggested remedies given. The results of this program will be used to construct a "state-of-the-art" pultrusion machine in the authors' laboratory. The initial findings provided input for a Quality Function Deployment (QFD) study which is basis for the functional specification for the pultrusion machine. By using QFD, capabilities of existing machines were determined and design requirements for an improved state-of-the-art machine were established. The QFD exercise provided an in-depth look at the relationship between desired machine capabilities and machine design requirements.

Composite wind turbine towers

Energy Technology Data Exchange (ETDEWEB)

Polyzois, D. [Manitoba Univ., Winnipeg, MB (Canada). Dept. of Civil Engineering

2008-07-01

This paper discussed experiments conducted to optimized the advanced composite materials such as fiberglass reinforced plastics (FRP) used to fabricate wind turbine towers. FRP materials are used in tubular steel, lattice, guyed, and reinforced concrete towers. The towers and turbine blades are transported in segments and assembled on-site, sometimes in offshore or remote locations.The FRP composites are used to build towers with a high strength-to-weight ratio as well as to provide resistance to chemical attacks and corrosion. Use of the materials has resulted in towers that do not require heavy installation equipment. Experimental programs were conducted to verify the structural behaviour of the tower structure's individual-scaled cells as well as to evaluate the performance of multi-cell assemblies. Joint assembly designs were optimized, and a filament winding machine was used to conduct the experimental study and to test individual cells. Failure mode analyses were conducted to determine local buckling and shear rupture. Tension, compression, and shear properties of the FRP materials were tested experimentally, and data from the test were then used to develop finite element models of the composite towers as well as to obtain load deflection curves and tip oscillation data. A case study of a 750 kW wind turbine in Churchill, Manitoba was used to test the design. tabs., figs.

Investigation of properties and performance of ceramic composite components: Final report on Phases 3 and 4

Energy Technology Data Exchange (ETDEWEB)

Curtin, W.A.; Halverson, H.; Carter, R.H.; Miraj, N.; Reifsnider, K.L. [Virginia Polytechnic Inst. and State Univ., Blacksburg, VA (United States)

1998-01-15

The objective of the Fossil Energy Advanced Research and Technology Development (AR and TD) Materials Program is to conduct research and development on materials for longer-term fossil energy applications as well as for generic needs of various fossil fuel technologies. The research program of the Materials Response Group at Virginia Tech addresses the need for reliable and durable structural ceramic composites to perform in high temperature environments. The research effort provides an experimental and analytical basis for the transition from properties of materials to performance of actual component structures. Phases 1 and 2 of the present program focused on the development of test capabilities, initial studies of component mechanical response under various conditions and the development of a life prediction methodology. These efforts have been described in previous reports. This report summarizes the major tasks completed under Phases 3 and 4 of the project. Overall, the authors have made significant progress in a broad spectrum of tasks in this program. Their efforts have encompassed component evaluation, assessment of new SiC-based composites with improved high-temperature potential, development of oxide coating materials for SiC, and the extension and development of new models for predicting the durability of composite components under specific operating conditions for various CMC applications. Each of these areas of work is an important area for achieving the ultimate goal of usable SiC-based composites in high-temperature corrosive environments typical of fossil energy applications.

Understanding Service Composition with Non-functional Properties Using Declarative Model-to-model Transformations

Directory of Open Access Journals (Sweden)

Max Mäuhlhäuser

2011-01-01

Full Text Available Developing applications comprising service composition is a complex task. Therefore, to lower the skill barrier for developers, it is important to describe the problem at hand on an abstract level and not to focus on implementation details. This can be done using declarative programming which allows to describe only the result of the problem (which is what the developer wants rather than the description of the implementation. We therefore use purely declarative model-to-model transformations written in a universal model transformation language which is capable of handling even non functional properties using optimization and mathematical programming. This makes it easier to understand and describe service composition and non-functional properties for the developer.

Chromium picolinate effects on body composition and muscular performance in wrestlers.

Science.gov (United States)

Walker, L S; Bemben, M G; Bemben, D A; Knehans, A W

1998-12-01

The purpose of this study was to assess the effects of 14 wk of chromium picolinate supplementation during the final 16 wk of a preseason resistance and conditioning program on body composition and neuromuscular performance in NCAA Division I wrestlers. During this phase of training, wrestlers are primarily interested in trying to improve physical performance and wrestling technique and are not engaged in severe, acute weight loss practices commonly employed before competition. This double-blinded, randomized placebo-controlled study involved 20 wrestlers from the University of Oklahoma assigned to either a treatment group (Cr+3; N = 7; 20.4 yr +/- 0.1) receiving 200 micrograms chromium picolinate daily, a placebo group (P; N = 7; 19.9 yr +/- 0.2), or a control group (C; N = 6; 20.2 yr +/- 0.1) using a stratified random sampling technique based on weight classification. Body composition, neuromuscular performance, metabolic performance, and serum insulin and glucose were measured before and immediately following the supplementation and training period. Repeated measures ANOVA indicated no significant changes in body composition for any of the groups. Aerobic power increased significantly (P pre- to post-test changes in bench press power were significant. These results suggest that chromium picolinate supplementation coupled with a typical preseason training program does not enhance body composition or performance variables beyond improvements seen with training alone.

The tensile strength of mechanical joint prototype of lontar fiber composite

Science.gov (United States)

Bale, Jefri; Adoe, Dominggus G. H.; Boimau, Kristomus; Sakera, Thomas

2018-03-01

In the present study, an experimental activity has been programmed to investigate the effect of joint prototype configuration on tensile strength of lontar (Borassus Flabellifer) fiber composite. To do so, a series of tests were conducted to establish the tensile strength of different joint prototype configuration specimen of lontar fiber composite. In addition, post observation of macroscope was used to map damage behavior. The analysis of lontar fiber composite is a challenge since the material has limited information than others natural fiber composites materials. The results shown that, under static tensile loading, the tensile strength of 13 MPa produced by single lap joint of lontar fiber composite is highest compare to 11 MPa of tensile strength generated by step lap joint and double lap joint where produced the lowest tensile strength of 6 MPa. It is concluded that the differences of tensile strength depend on the geometric dimensions of the cross-sectional area and stress distribution of each joint prototype configuration.

Carbon Foam Self-Heated Tooling for Out-of-Autoclave Composites Manufacturing, Phase I

Data.gov (United States)

National Aeronautics and Space Administration — This proposal addresses NASA's need for non-autoclave composites manufacture. The Constellation program, including the Ares V launch vehicle, will require very...

On the simulation of kink bands in fiber reinforced composites

DEFF Research Database (Denmark)

Sørensen, K.D.; Mikkelsen, Lars Pilgaard; Jensen, H.M.

2007-01-01

Simulations of kink band formation in fiber reinforced composites are carried out using the commercial finite element program ABAQUS. A smeared-out, plane constitutive model for fiber reinforced materials is implemented as a user subroutine, and effects of fiber misalignment on elastic and plastic...

Exercise affects body composition but not weight in postmenopausal women.

NARCIS (Netherlands)

Velthuis, M.J.; Schuit, A.J.; Peeters, P.H.M.; Monninkhof, E.M.

2009-01-01

OBJECTIVE: The aim of this study was to investigate the effect of a 12-month moderate-to-vigorous exercise program combining aerobic and muscle strength training on body composition among sedentary, postmenopausal women. METHODS: A randomized controlled trial was conducted. A total of 189 sedentary

A Computer Program for Short Circuit Analysis of Electric Power ...

African Journals Online (AJOL)

The Short Circuit Analysis Program (SCAP) is to be used to assess the composite effects of unbalanced and balanced faults on the overall reliability of electric power system. The program uses the symmetrical components method to compute all phase and sequence quantities for any bus or branch of a given power network ...

Experimental and Numerical Study of FRP Encased Composite Concrete Columns

Directory of Open Access Journals (Sweden)

Mohsen Ishaghian

2017-02-01

Full Text Available A new type of composite column is presented and assessed through experimental testing and numerical modeling. The objective of this research is to investigate design options for a composite column without the use of ferrous materials. This is to avoid the current problem of deterioration of concrete due to expansion of rusting reinforcement members. Such a target can be achieved by replacing the steel reinforcement of concrete columns with pultruded I-shape glass FRP structural sections. The composite column utilizes a glass FRP tube that surrounds a pultruded I-section glass FRP, which is subsequently filled with concrete. The GFRP tube acts as a stay-in-place form in addition to providing confinement to the concrete. A total of four composite columns were tested under monotonic axial loading. The experimental ultimate capacity of each of the tested composite column was compared to the predicted numerical capacity using ANSYS program. The comparison showed that the predicted numerical values were in good agreement with the experimental ones.

U.S. Advanced Materials Development Program for steam generators

International Nuclear Information System (INIS)

Patriarca, P.; Harkness, S.D.; Duke, J.M.

1975-01-01

The selection of construction materials for LMFBR steam generators is reviewed, presenting the advantages and limitations of 2 1 / 2 Cr-1 Mo steel selected for the Clinch River Breeder Reactor Plant. These limitations indicate that further development of high-strength ferritic steels containing 9 to 12 percent Cr and the high-nickel Alloy 800 could lead to superior materials, and programs to develop these materials have been started. Combustion Engineering has surveyed the experience with the high-strength ferritic steels and prepared ingots of 26 selected compositions. Charpy V-notch tests and metallography have been used to characterize these alloys, and optimum welding rod compositions for these alloys are under development. Westinghouse-Tampa is undertaking a program to gain code acceptance of Alloy 800. A program has been set up to provide the information required for design, justification, and fabrication of reliable components. Progress has been made on characterization, the role of tertiary creep in failure, and the development of welding processes. (U.S.)

Baseline atmospheric program Australia 1993

International Nuclear Information System (INIS)

Francey, R.J.; Dick, A.L.; Derek, N.

1996-01-01

This publication reports activities, program summaries and data from the Cape Grim Baseline Air Pollution Station in Tasmania, during the calendar year 1993. These activities represent Australia's main contribution to the Background Air Pollution Monitoring Network (BAPMoN), part of the World Meteorological Organization's Global Atmosphere Watch (GAW). The report includes 5 research reports covering trace gas sampling, ozone and radon interdependence, analysis of atmospheric dimethylsulfide and carbon-disulfide, sampling of trace gas composition of the troposphere, and sulfur aerosol/CCN relationship in marine air. Summaries of program reports for the calendar year 1993 are also included. Tabs., figs., refs

Palliative Workforce Development and a Regional Training Program.

Science.gov (United States)

O'Mahony, Sean; Levine, Stacie; Baron, Aliza; Johnson, Tricia J; Ansari, Aziz; Leyva, Ileana; Marschke, Michael; Szmuilowicz, Eytan; Deamant, Catherine

2018-01-01

Our primary aims were to assess growth in the local hospital based workforce, changes in the composition of the workforce and use of an interdisciplinary team, and sources of support for palliative medicine teams in hospitals participating in a regional palliative training program in Chicago. PC program directors and administrators at 16 sites were sent an electronic survey on institutional and PC program characteristics such as: hospital type, number of beds, PC staffing composition, PC programs offered, start-up years, PC service utilization and sources of financial support for fiscal years 2012 and 2014. The median number of consultations reported for existing programs in 2012 was 345 (IQR 109 - 2168) compared with 840 (IQR 320 - 4268) in 2014. At the same time there were small increases in the overall team size from a median of 3.2 full time equivalent positions (FTE) in 2012 to 3.3 FTE in 2013, with a median increase of 0.4 (IQR 0-1.0). Discharge to hospice was more common than deaths in the acute care setting in hospitals with palliative medicine teams that included both social workers and advanced practice nurses ( p < .0001). Given the shortage of palliative medicine specialist providers more emphasis should be placed on training other clinicians to provide primary level palliative care while addressing the need to hire sufficient workforce to care for seriously ill patients.

Estimation of physical properties of laminated composites via the method of inverse vibration problem

Energy Technology Data Exchange (ETDEWEB)

Balci, Murat [Dept. of Mechanical Engineering, Bayburt University, Bayburt (Turkmenistan); Gundogdu, Omer [Dept. of Mechanical Engineering, Ataturk University, Erzurum (Turkmenistan)

2017-01-15

In this study, estimation of some physical properties of a laminated composite plate was conducted via the inverse vibration problem. Laminated composite plate was modelled and simulated to obtain vibration responses for different length-to-thickness ratio in ANSYS. Furthermore, a numerical finite element model was developed for the laminated composite utilizing the Kirchhoff plate theory and programmed in MATLAB for simulations. Optimizing the difference between these two vibration responses, inverse vibration problem was solved to obtain some of the physical properties of the laminated composite using genetic algorithms. The estimated parameters are compared with the theoretical results, and a very good correspondence was observed.

Estimation of physical properties of laminated composites via the method of inverse vibration problem

International Nuclear Information System (INIS)

Balci, Murat; Gundogdu, Omer

2017-01-01

In this study, estimation of some physical properties of a laminated composite plate was conducted via the inverse vibration problem. Laminated composite plate was modelled and simulated to obtain vibration responses for different length-to-thickness ratio in ANSYS. Furthermore, a numerical finite element model was developed for the laminated composite utilizing the Kirchhoff plate theory and programmed in MATLAB for simulations. Optimizing the difference between these two vibration responses, inverse vibration problem was solved to obtain some of the physical properties of the laminated composite using genetic algorithms. The estimated parameters are compared with the theoretical results, and a very good correspondence was observed

Development of bonded composite doublers for the repair of oil recovery equipment.

Energy Technology Data Exchange (ETDEWEB)

Roach, David W.; Rackow, Kirk A.

2005-06-01

An unavoidable by-product of a metallic structure's use is the appearance of crack and corrosion flaws. Economic barriers to the replacement of these structures have created an aging infrastructure and placed even greater demands on efficient and safe repair methods. In the past decade, an advanced composite repair technology has made great strides in commercial aviation use. Extensive testing and analysis, through joint programs between the Sandia Labs FAA Airworthiness Assurance Center and the aviation industry, have proven that composite materials can be used to repair damaged aluminum structure. Successful pilot programs have produced flight performance history to establish the durability of bonded composite patches as a permanent repair on commercial aircraft structures. With this foundation in place, this effort is adapting bonded composite repair technology to civil structures. The use of bonded composite doublers has the potential to correct the difficulties associated with current repair techniques and the ability to be applied where there are no rehabilitation options. It promises to be cost-effective with minimal disruption to the users of the structure. This report concludes a study into the application of composite patches on thick steel structures typically used in mining operations. Extreme fatigue, temperature, erosive, and corrosive environments induce an array of equipment damage. The current weld repair techniques for these structures provide a fatigue life that is inferior to that of the original plate. Subsequent cracking must be revisited on a regular basis. The use of composite doublers, which do not have brittle fracture problems such as those inherent in welds, can help extend the structure's fatigue life and reduce the equipment downtime. Two of the main issues for adapting aircraft composite repairs to civil applications are developing an installation technique for carbon steel and accommodating large repairs on extremely thick

Bimetallic iron and cobalt incorporated MFI/MCM-41 composite and its catalytic properties

International Nuclear Information System (INIS)

Li, Baoshan; Xu, Junqing; Li, Xiao; Liu, Jianjun; Zuo, Shengli; Pan, Zhiyun; Wu, Ziyu

2012-01-01

Graphical abstract: The formation of FeCo-MFI/MCM-41 composite is based on two steps, the first step of synthesizing the MFI-type proto-zeolite unites under hydrothermal conditions. The second step of assembling these zeolite fragment together new silica and heteroatom source on the CTAB surfactant micelle to synthesize the mesoporous product with hexagonal structure. Highlights: ► Bimetallic iron and cobalt incorporated MFI/MCM-41 composite was prepared using templating method. ► FeCo-MFI/MCM-41 composite simultaneously possessed two kinds of meso- and micro-porous structures. ► Iron and cobalt ions incorporated into the silica framework with tetrahedral coordination. -- Abstract: The MFI/MCM-41 composite material with bimetallic Fe and Co incorporation was prepared using templating method via a two-step hydrothermal crystallization procedure. The obtained products were characterized by a series of techniques including powder X-ray diffraction, N 2 sorption, transmission electron microscopy, scanning electron microscope, H 2 temperature programmed reduction, thermal analyses, and X-ray absorption fine structure spectroscopy of the Fe and Co K-edge. The catalytic properties of the products were investigated by residual oil hydrocracking reactions. Characterization results showed that the FeCo-MFI/MCM-41 composite simultaneously possessed two kinds of stable meso- and micro-porous structures. Iron and cobalt ions were incorporated into the silicon framework, which was confirmed by H 2 temperature programmed reduction and X-ray absorption fine structure spectroscopy. This composite presented excellent activities in hydrocracking of residual oil, which was superior to the pure materials of silicate-1/MCM-41.

Composite gravity and composite supergravity

International Nuclear Information System (INIS)

Lukierski, J.

1982-09-01

It is known that the composite YM H-gauge theory can be constructed from σ-fields taking values in a symmetric Riemannian space G/H. We extend such a framework to graded σ-fields taking values in supercosets. We show that from supercoset σ-fields one can construct composite gravity, and from supercoset σ-superfields the composite supergravity models. (author)

Data on post irradiation experiments of heat resistant ceramic composite materials. PIE for 97M-13A

Energy Technology Data Exchange (ETDEWEB)

Baba, Shin-ichi; Ishihara, Masahiro; Souzawa, Shizuo [Japan Atomic Energy Research Inst., Oarai, Ibaraki (Japan). Oarai Research Establishment; Sekino, Hajime [Japan Atomic Energy Research Inst., Tokai, Ibaraki (Japan). Tokai Research Establishment

2003-03-01

The research on the radiation damage mechanism of heat resistant ceramic composite materials is one of the research subjects of the innovative basic research in the field of high temperature engineering, using the High Temperature engineering Test Reactor (HTTR). Three series of irradiation tests on the heat resistant ceramic composite materials, first to third irradiation test program, were carried out using the Japan Material Testing Reactor (JMTR). This is a summary report on the first irradiation test program; irradiation induced dimensional change, thermal expansion coefficient, X-ray diffraction and {gamma}-ray spectrum are reported. (author)

Process conditions and volumetric composition in composites

DEFF Research Database (Denmark)

Madsen, Bo

2013-01-01

The obtainable volumetric composition in composites is linked to the gravimetric composition, and it is influenced by the conditions of the manufacturing process. A model for the volumetric composition is presented, where the volume fractions of fibers, matrix and porosity are calculated...... as a function of the fiber weight fraction, and where parameters are included for the composite microstructure, and the fiber assembly compaction behavior. Based on experimental data of composites manufactured with different process conditions, together with model predictions, different types of process related...... effects are analyzed. The applied consolidation pressure is found to have a marked effect on the volumetric composition. A power-law relationship is found to well describe the found relations between the maximum obtainable fiber volume fraction and the consolidation pressure. The degree of fiber...

Improving Turbine Performance with Ceramic Matrix Composites

Science.gov (United States)

DiCarlo, James A.

2007-01-01

Under the new NASA Fundamental Aeronautics Program, efforts are on-going within the Supersonics Project aimed at the implementation of advanced SiC/SiC ceramic composites into hot section components of future gas turbine engines. Due to recent NASA advancements in SiC-based fibers and matrices, these composites are lighter and capable of much higher service temperatures than current metallic superalloys, which in turn will allow the engines to operate at higher efficiencies and reduced emissions. This presentation briefly reviews studies within Task 6.3.3 that are primarily aimed at developing physics-based concepts, tools, and process/property models for micro- and macro-structural design, fabrication, and lifing of SiC/SiC turbine components in general and airfoils in particular. Particular emphasis is currently being placed on understanding and modeling (1) creep effects on residual stress development within the component, (2) fiber architecture effects on key composite properties such as design strength, and (3) preform formation processes so that the optimum architectures can be implemented into complex-shaped components, such as turbine vanes and blades.

Kevlar/PMR-15 polyimide matrix composite for a complex shaped DC-9 drag reduction fairing

Science.gov (United States)

Kawai, R. T.; Mccarthy, R. F.; Willer, M. S.; Hrach, F. J.

1982-01-01

The Aircraft Energy Efficiency (ACEE) Program was established by NASA to improve the fuel efficiency of commercial transport aircraft and thereby to reduce the amount of fuel consumed by the air transportation industry. One of the final items developed by the program is an improved fairing which is the aft closure for the thrust reverser actuators on the JT8D nacelles on DC-9 aircraft. The reduced-drag fairing uses, in the interest of weight savings, an advanced composite construction. The composite material contains Kevlar 49 fibers in a PMR-15 matrix. Attention is given to the aerodynamic configuration, the material system, and aspects of fabrication development.

Optically transparent composite diamond/Ti electrodes

Czech Academy of Sciences Publication Activity Database

Ashcheulov, Petr; Taylor, Andrew; More Chevalier, Joris; Kovalenko, A.; Remeš, Zdeněk; Drahokoupil, Jan; Hubík, Pavel; Fekete, Ladislav; Klimša, Ladislav; Kopeček, Jaromír; Remiášová, Jarmila; Kohout, Michal; Frank, Otakar; Kavan, Ladislav; Mortet, Vincent

2017-01-01

Roč. 119, Aug (2017), s. 179-189 ISSN 0008-6223 R&D Projects: GA MŠk LO1409; GA MŠk LM2015088; GA ČR GA13-31783S Grant - others:FUNBIO(XE) CZ.2.16/3.1.00/21568; AV ČR(CZ) Fellowship J. E. Purkyně; AV ČR(CZ) MSM100101602 Program:Program na podporu mezinárodní spolupráce začínajících výzkumných pracovníků Institutional support: RVO:68378271 ; RVO:61388955 Keywords : diamond * transparent film * composite electrode * conductive thin film Subject RIV: BM - Solid Matter Physics ; Magnetism; CF - Physical ; Theoretical Chemistry (UFCH-W) OBOR OECD: Condensed matter physics (including formerly solid state physics, supercond.); Physical chemistry (UFCH-W) Impact factor: 6.337, year: 2016

Multi-shape active composites by 3D printing of digital shape memory polymers.

Science.gov (United States)

Wu, Jiangtao; Yuan, Chao; Ding, Zhen; Isakov, Michael; Mao, Yiqi; Wang, Tiejun; Dunn, Martin L; Qi, H Jerry

2016-04-13

Recent research using 3D printing to create active structures has added an exciting new dimension to 3D printing technology. After being printed, these active, often composite, materials can change their shape over time; this has been termed as 4D printing. In this paper, we demonstrate the design and manufacture of active composites that can take multiple shapes, depending on the environmental temperature. This is achieved by 3D printing layered composite structures with multiple families of shape memory polymer (SMP) fibers - digital SMPs - with different glass transition temperatures (Tg) to control the transformation of the structure. After a simple single-step thermomechanical programming process, the fiber families can be sequentially activated to bend when the temperature is increased. By tuning the volume fraction of the fibers, bending deformation can be controlled. We develop a theoretical model to predict the deformation behavior for better understanding the phenomena and aiding the design. We also design and print several flat 2D structures that can be programmed to fold and open themselves when subjected to heat. With the advantages of an easy fabrication process and the controllable multi-shape memory effect, the printed SMP composites have a great potential in 4D printing applications.

Multi-shape active composites by 3D printing of digital shape memory polymers

Science.gov (United States)

Wu, Jiangtao; Yuan, Chao; Ding, Zhen; Isakov, Michael; Mao, Yiqi; Wang, Tiejun; Dunn, Martin L.; Qi, H. Jerry

2016-04-01

Recent research using 3D printing to create active structures has added an exciting new dimension to 3D printing technology. After being printed, these active, often composite, materials can change their shape over time; this has been termed as 4D printing. In this paper, we demonstrate the design and manufacture of active composites that can take multiple shapes, depending on the environmental temperature. This is achieved by 3D printing layered composite structures with multiple families of shape memory polymer (SMP) fibers - digital SMPs - with different glass transition temperatures (Tg) to control the transformation of the structure. After a simple single-step thermomechanical programming process, the fiber families can be sequentially activated to bend when the temperature is increased. By tuning the volume fraction of the fibers, bending deformation can be controlled. We develop a theoretical model to predict the deformation behavior for better understanding the phenomena and aiding the design. We also design and print several flat 2D structures that can be programmed to fold and open themselves when subjected to heat. With the advantages of an easy fabrication process and the controllable multi-shape memory effect, the printed SMP composites have a great potential in 4D printing applications.

On the Tuning and the Mass of the Composite Higgs

CERN Document Server

Panico, Giuliano; Tesi, Andrea; Wulzer, Andrea

2013-01-01

We analyze quantitatively the tuning of composite Higgs models with partial compositeness and its interplay with the predicted Higgs mass. In this respect we identify three classes of models, characterized by different quantum numbers of the fermionic colored resonances associated with the top quark, the so-called top partners. The main result of this classification is that in all models with moderate tuning a light Higgs, of 125 GeV mass, requires the presence of light top partners, around 1 TeV. The minimal tuning is comparable to the one of the most attractive supersymmetric models in particular the ones realizing Natural SUSY. This gives further support to an extensive program of top partners searches at the LHC that can already probe the natural region of composite Higgs models.

A reliability based stress-life evaluation of aluminium-graphite particulate composites

International Nuclear Information System (INIS)

Achutha, M.V.; Sridhara, B.K.; Abdul Budan, D.

2008-01-01

Fatigue tests were conducted on sand cast aluminium-graphite composite specimens on Rotating Beam Fatigue Testing Machine with three different stress levels. Aluminium-graphite (LM 25-5% graphite) composite was processed by closed mould sand casting method. Three-stress level fatigue test program was planned for carrying out fatigue experiments. Three different stress levels selected for fatigue experiments were a fraction of ultimate tensile strength. Statistical design of fatigue experiments was carried out to determine the sample size at each stress level. Experimental results are presented in the form of stress-life (S-N) curves and reliability-stress-life (R-S-N) curves, which are helpful for designers. The S-N curve of the aluminium-graphite composite was compared with its matrix alloy LM 25. Comparison revealed that the fatigue behaviour of the aluminium-graphite composite is superior to that of the matrix alloy

The advanced thermionics initiative...program update

International Nuclear Information System (INIS)

Lamp, T.R.; Donovan, B.D.

1993-01-01

The United States Air Force has had a long standing interest in thermionic space power dating back to the early 1960s when a heat pipe cooled thermionic converter was demonstrated through work at the predecessor to Wright Laboratory (WL). With the exception of the short hiatus in the mid-70s, Air Force thermionics work at Wright Laboratory has continued to the present time with thermionic technology programs including the burst power thermionic phase change concepts, heat pipe cooled planar diodes, and advanced in-core concept developments such as composite materials, insulators and oxygenation. The Advanced Thermionics Initiative (ATI) program was organized to integrate thermionic technology advances into a converter suitable for in-core reactor applications in the 10 to 40 kWe power range. As an advanced thermionics technology program, the charter and philosophy of the ATI program is to provide the needed advanced converter concepts in support of national thermionic space power programs

Mechanical interaction of Engineered Cementitious Composite (ECC) reinforced with Fiber Reinforced Polymer (FRP) rebar in tensile loading

DEFF Research Database (Denmark)

Lárusson, Lárus Helgi; Fischer, Gregor; Jönsson, Jeppe

2010-01-01

This paper introduces a preliminary study of the composite interaction of Engineered Cementitious Composite (ECC), reinforced with Glass Fiber Reinforced Polymer (GFRP) rebar. The main topic of this paper will focus on the interaction of the two materials (ECC and GFRP) during axial loading......, particularly in post cracking phase of the concrete matrix. The experimental program carried out in this study examined composite behavior under monotonic and cyclic loading of the specimens in the elastic and inelastic deformation phases. The stiffness development of the composite during loading was evaluated...

Design of benign matrix drums for the non-destructive assay performance demonstration program for the National TRU Program

International Nuclear Information System (INIS)

Becker, G.K.

1996-09-01

Regulatory compliance programs associated with the Department of Energy (DOE) Waste Isolation Pilot Plant (WIPP) Transuranic (TRU) Waste Characterization Program (the Program) require the collection of waste characterization data of known quality to support repository performance assessment, permitting, and associated activities. Blind audit samples, referred to as PDP (performance demonstration program) samples, are devices used in the NDA PDP program to acquire waste NDA system performance data per defined measurement routines. As defined under the current NDA PDP Program Plan, a PDP sample consists of a DOT 17C 55-gallon PDP matrix drum configured with insertable radioactive standards, working reference materials (WRMs). The particular manner in which the matrix drum and PDP standard(s) are combined is a function of the waste NDA system performance test objectives of a given cycle. The scope of this document is confined to the design of the PDP drum radioactive standard internal support structure, the matrix type and the as installed configuration. The term benign is used to designate a matrix possessing properties which are nominally non-interfering to waste NDA measurement techniques. Measurement interference sources are technique specific but include attributes such as: high matrix density, heterogeneous matrix distributions, matrix compositions containing high moderator/high Z element concentrations, etc. To the extent practicable the matrix drum design should not unduly bias one NDA modality over another due to the manner in which the matrix drum configuration manifests itself to the measurement system. To this end the PDP matrix drum configuration and composition detailed below is driven primarily by the intent to minimize the incorporation of matrix attributes known to interfere with fundamental waste NDA modalities, i.e. neutron and gamma based techniques

DP: Parameter Display Page Program

International Nuclear Information System (INIS)

Anderson, M.

1994-01-01

The Parameter Display Page program (DP) is a Motif/X11-based program to allow easily configured, dynamic device and process variable monitoring and manipulation in the EPICS environment. DP provides a tabular data format for interactive viewing and manipulation of device and process variable statistics, as well as formatted PostScript output to files and printers. DP understands and operates in two (unfortunately disjoint at this time) namespaces in the EPICS environment ''devices'' and ''process variables''. The higher level namespace of devices includes Composite and Atomic Devices registered via the Device Access server; the lower level (flat) namespace is that of normal Process Variables accessible via Channel Access

Implementing a campus wide recycling program

International Nuclear Information System (INIS)

Alvarez, L.

2002-01-01

'Full text:' The University of Windsor is currently expanding its recycling program to include all buildings on campus, but faces two challenges: 1) uncertainty about the current waste composition and distribution on campus; and 2) uncertainty about the effectiveness of increased recycling. This project assesses the current waste composition and the attitudes of the students towards recycling, and evaluates the effectiveness of proposed recycling activities. At present, paper is the only material that is collected throughout the entire campus. Except for two buildings, all other potentially recyclable materials within buildings, such as metal, glass, and plastic beverage containers, are discarded. The main focus of this research is on beverage containers as they represent clearly identifiable materials, but other materials were examined as well. To quantify the waste, different buildings on campus were classified according to their function: academic,operational and administrative. The waste composition study indicated that approximately 33% of the campus waste which is landfilled is composed of potentially recyclable material. A survey was then conducted to gauge the campus population's views on recycling issues that could affect the design of a recycling program. Interestingly, 97% of the respondents indicated a high willingness to recycle, but were uncertain as to how and where to recycle on campus. The project is currently assessing potential diversion rates using new, clearly identifiable recycling receptacles placed within selected classrooms for all major materials. There is a significant tradeoff however because the cost for new receptacles is considerable: multiple materials containers are often placed in high pedestrian traffic locations (e.g., hallways) and not always in classrooms,of which there are often many. This project will evaluate the basic benefits and costs of implementing a more comprehensive recycling program, and recommend how other

Aquatic Species Program Review: Proceedings of the March 1983 Principal Investigators Meeting

Energy Technology Data Exchange (ETDEWEB)

1983-06-01

The Aquatic Species Program (ASP) addresses the utilization of plant biomass that naturally occurs in wetland or submerged areas. Processes are being developed through this program to make use of such aquatic species, capitalizing on their inherent capacity for rapid growth as well as their extraordinary chemical compositions.

"Embarrassingly White": Faculty Racial Disparities in American Recreation, Park, and Tourism Programs

Science.gov (United States)

Mowatt, Rasul A.; Johnson, Corey W.; Roberts, Nina S.; Kivel, B. Dana

2016-01-01

The recruitment and retention of faculty and students of color is a long-standing challenge in academic programs focusing on leisure studies, parks, recreation, and tourism. However, when confronting the predominantly white composition of educational programs, many evade or, at most, acknowledge the situation as a "deficit." Few offer…

Tensile and Flexural Test on Kenaf Hybrid Composites

Science.gov (United States)

Salleh, Z.; Yunus, S.; Masdek, N. R. N. M.; Taib, Y. M.; Azhar, I. I. S.; Hyie, K. M.

2018-03-01

The widely use of synthetic materials like carbon and fiberglass in various industries such as automotive and aircraft has lead to human health and environment problems. Therefore, the use of natural fibres such as kenaf has received higher attention as reinforcement. Kenaf or the scientific name is Hibiscus Cannabinus. L is one of the group of Malvecea plant which in the early days, the application of kenaf served only rope and canvas. However, it has more advantages than synthetic materials such as; widely availaible, renewable, lightweight, non-abbrasiveness during processing, high specific strength, free from health hazard and biodegradeable. This study was carried out to investigate the effects of different arrangement of kenaf and fiberglass composites on Young’s Modulus. The material composite was hardened with polyester resin and their properties was characterized. The tensile and the flexural properties is determined using an Instron universal tensile testing machine and carried out by following ASTM D3039 for tensile and ASTM D790 for a flexural test. The experimental program was designed to correlate the flexural and tensile Young’s Modulus of kenaf and fiberglass composite under the same load condition but different arrangement of kenaf and fiberglass on the mold . The resistance to change in shape was described by the behavior and characteristic of the composite materials. The stiffness or the elastic modulus of the composite material was determined at the end of the experiment. The results obtained show that the [±90FG/0/90/90/0/±90FG] kenaf/fiberglass composite arrangement has the highest elastic value.

Gut microbiota composition may relate to weight loss rate in obese pet dogs

DEFF Research Database (Denmark)

Kieler, Ida Nordang; Kamal, Shamrulazhar; Vitger, Anne Désiré

2017-01-01

Obese dogs seem to have a different gut microbiome (GM) composition compared to lean dogs, and in humans, GM composition may negatively impact the ability to lose weight in some individuals. The purpose of this study was to investigate the interaction between exercise, weight-loss and the composi......Obese dogs seem to have a different gut microbiome (GM) composition compared to lean dogs, and in humans, GM composition may negatively impact the ability to lose weight in some individuals. The purpose of this study was to investigate the interaction between exercise, weight......-loss and the composition of GM in dogs. Eighteen obese pet dogs were recruited for a 12-week weight-loss intervention. All dogs were fed restrictively with a commercial high-protein/high-fibre dry diet, and eight of these dogs were enrolled in an exercise program in addition to the diet intervention. Faecal samples were...

A Model of Computation for Bit-Level Concurrent Computing and Programming: APEC

Science.gov (United States)

Ajiro, Takashi; Tsuchida, Kensei

A concurrent model of computation and a language based on the model for bit-level operation are useful for developing asynchronous and concurrent programs compositionally, which frequently use bit-level operations. Some examples are programs for video games, hardware emulation (including virtual machines), and signal processing. However, few models and languages are optimized and oriented to bit-level concurrent computation. We previously developed a visual programming language called A-BITS for bit-level concurrent programming. The language is based on a dataflow-like model that computes using processes that provide serial bit-level operations and FIFO buffers connected to them. It can express bit-level computation naturally and develop compositionally. We then devised a concurrent computation model called APEC (Asynchronous Program Elements Connection) for bit-level concurrent computation. This model enables precise and formal expression of the process of computation, and a notion of primitive program elements for controlling and operating can be expressed synthetically. Specifically, the model is based on a notion of uniform primitive processes, called primitives, that have three terminals and four ordered rules at most, as well as on bidirectional communication using vehicles called carriers. A new notion is that a carrier moving between two terminals can briefly express some kinds of computation such as synchronization and bidirectional communication. The model's properties make it most applicable to bit-level computation compositionally, since the uniform computation elements are enough to develop components that have practical functionality. Through future application of the model, our research may enable further research on a base model of fine-grain parallel computer architecture, since the model is suitable for expressing massive concurrency by a network of primitives.

Statistical data for the tensile properties of natural fibre composites

Directory of Open Access Journals (Sweden)

J.P. Torres

2017-06-01

Full Text Available This article features a large statistical database on the tensile properties of natural fibre reinforced composite laminates. The data presented here corresponds to a comprehensive experimental testing program of several composite systems including: different material constituents (epoxy and vinyl ester resins; flax, jute and carbon fibres, different fibre configurations (short-fibre mats, unidirectional, and plain, twill and satin woven fabrics and different fibre orientations (0°, 90°, and [0,90] angle plies. For each material, ~50 specimens were tested under uniaxial tensile loading. Here, we provide the complete set of stress–strain curves together with the statistical distributions of their calculated elastic modulus, strength and failure strain. The data is also provided as support material for the research article: “The mechanical properties of natural fibre composite laminates: A statistical study” [1].

A Strategy for Efficiently Verifying Requirements Specifications Using Composition and Invariants

Science.gov (United States)

2003-09-05

Colle - sur - Loup , France, Oct. 1984. Springer-Verlag. [34] J. Ramish. Empirical studies of compositional abstraction. Technical report, Naval Research...global to modular temporal rea- soning about programs. In K. R. Apt, editor, Proc. NATO Adv. Study Inst. on Logics and Models of Concurrent Systems, La

Addition to the Lewis Chemical Equilibrium Program to allow computation from coal composition data

Science.gov (United States)

Sevigny, R.

1980-01-01

Changes made to the Coal Gasification Project are reported. The program was developed by equilibrium combustion in rocket engines. It can be applied directly to the entrained flow coal gasification process. The particular problem addressed is the reduction of the coal data into a form suitable to the program, since the manual process is involved and error prone. A similar problem in relating the normal output of the program to parameters meaningful to the coal gasification process is also addressed.

Volumetric composition in composites and historical data

DEFF Research Database (Denmark)

Lilholt, Hans; Madsen, Bo

2013-01-01

The obtainable volumetric composition in composites is of importance for the prediction of mechanical and physical properties, and in particular to assess the best possible (normally the highest) values for these properties. The volumetric model for the composition of (fibrous) composites gives...... guidance to the optimal combination of fibre content, matrix content and porosity content, in order to achieve the best obtainable properties. Several composite materials systems have been shown to be handleable with this model. An extensive series of experimental data for the system of cellulose fibres...... and polymer (resin) was produced in 1942 – 1944, and these data have been (re-)analysed by the volumetric composition model, and the property values for density, stiffness and strength have been evaluated. Good agreement has been obtained and some further observations have been extracted from the analysis....

Complete Subsurface Elemental Composition Measurements With PING

Science.gov (United States)

Parsons, A. M.

2012-01-01

The Probing In situ with Neutrons and Gamma rays (PING) instrument will measure the complete bulk elemental composition of the subsurface of Mars as well as any other solid planetary body. PING can thus be a highly effective tool for both detailed local geochemistry science investigations and precision measurements of Mars subsurface reSOurces in preparation for future human exploration. As such, PING is thus fully capable of meeting a majority of both ncar and far term elements in Challenge #1 presented for this conference. Measuring the ncar subsurface composition of Mars will enable many of the MEPAG science goals and will be key to filling an important Strategic Knowledge Gap with regard to In situ Resources Utilization (ISRU) needs for human exploration. [1, 2] PING will thus fill an important niche in the Mars Exploration Program.

Composition

DEFF Research Database (Denmark)

Bergstrøm-Nielsen, Carl

2011-01-01

Strategies are open compositions to be realised by improvising musicians. See more about my composition practise in the entry "Composition - General Introduction". Caution: streaming the sound files will in some cases only provide a few minutes' sample. Please DOWNLOAD them to hear them in full...

Synopsis of the temporal variation of particulate matter composition and size.

Science.gov (United States)

Demerjian, Kenneth L; Mohnen, Volker A

2008-02-01

A synopsis of the detailed temporal variation of the size and number distribution of particulate matter (PM) and its chemical composition on the basis of measurements performed by several regional research consortia funded by the U.S. Environmental Protection Agency (EPA) PM Supersite Program is presented. This program deployed and evaluated a variety of research and emerging commercial measurement technologies to investigate the physical and chemical properties of atmospheric aerosols at a level of detail never before achieved. Most notably these studies demonstrated that systematic size-segregated measurements of mass, number, and associated chemical composition of the fine (PM2.5) and ultrafine (PM0.1) fraction of ambient aerosol with a time resolution down to minutes and less is achievable. A wealth of new information on the temporal variation of aerosol has been added to the existing knowledge pool that can be mined to resolve outstanding research and policy-related questions. This paper explores the nature of temporal variations (on time scales from several minutes to hours) in the chemical and physical properties of PM and its implications in the identification of PM formation processes, and source attribution (primary versus secondary), the contribution of local versus transported PM and the development of effective PM control strategies. The PM Supersite results summarized indicate that location, time of day, and season significantly influence not only the mass and chemical composition but also the size-resolved chemical/elemental composition of PM. Ambient measurements also show that ultrafine particles have different compositions and make up only a small portion of the PM mass concentration compared with inhalable coarse and fine particles, but their number concentration is significantly larger than their coarse or fine counterparts. PM size classes show differences in the relative amounts of nitrates, sulfates, crustal materials, and most especially

Composition

DEFF Research Database (Denmark)

2014-01-01

Memory Pieces are open compositions to be realised solo by an improvising musicians. See more about my composition practise in the entry "Composition - General Introduction". Caution: streaming the sound files will in some cases only provide a few minutes' sample. Please DOWNLOAD them to hear them...

On the Mechanical Behavior of Advanced Composite Material Structures

Science.gov (United States)

Vinson, Jack

During the period between 1993 and 2004, the author, as well as some colleagues and graduate students, had the honor to be supported by the Office of Naval Research to conduct research in several aspects of the behavior of structures composed of composite materials. The topics involved in this research program were numerous, but all contributed to increasing the understanding of how various structures that are useful for marine applications behaved. More specifically, the research topics focused on the reaction of structures that were made of fiber reinforced polymer matrix composites when subjected to various loads and environmental conditions. This included the behavior of beam, plate/panel and shell structures. It involved studies that are applicable to fiberglass, graphite/carbon and Kevlar fibers imbedded in epoxy, polyester and other polymeric matrices. Unidirectional, cross-ply, angle ply, and woven composites were involved, both in laminated, monocoque as well as in sandwich constructions. Mid-plane symmetric as well as asymmetric laminates were studied, the latter involving bending-stretching coupling and other couplings that only can be achieved with advanced composite materials. The composite structures studied involved static loads, dynamic loading, shock loading as well as thermal and hygrothermal environments. One major consideration was determining the mechanical properties of composite materials subjected to high strain rates because the mechanical properties vary so significantly as the strain rate increases. A considerable number of references are cited for further reading and study for those interested.

Thermal behavior of La2O3/Nio composite prepared by sol-gel method

International Nuclear Information System (INIS)

Sakallioglu, M.

2005-01-01

The La 2 O 3 /NiO composite was prepared by sol-gel method by using transition metal oxides (La 2 O 3 /NiO). The variation of specific heat capacity Cp with temperature for La2O3/NiO composite was investigated by DSC. The heat capacity curve was taken with a heating rate of 20 degrees/min between 0-100 degrees. The variation of specific heat capacity was found by PKI Muse Standard Analysis Program. The thermal stability of the La 2 O 3 /NiO composite was investigated by thermogravimetric analysis (TG) in air atmosphere at a heating rate of 20 degrees/min. The weight loss of La 2 O 3 /NiO composite was determined by the variation of temperature

Automated x-ray inspection of composites at northrop aircraft

International Nuclear Information System (INIS)

Murphy, W.J. Jr.; Nutter, R.L.; Patricelli, F.

1985-01-01

The Northrop automated x-ray inspection system (AXIS) has evolved from a research and development program initiated in 1981 to reduce increasing inspection costs; and reduce inspection times to stay abreast with increasing F/A-18A production. The goal of the program was to develop an automated production system that would meet existing inspection requirements; automate handling and alignment; and replace film for the inspection of F/A-18A composite assemblies and laminates. Originally, the program was supported completely by Northrop internal finding. However in 1984 it became part of the Navy Industrial Modernization Incentive Program (IMIP) with joint funding. The program was selected by the Navy because of its great potential to reduce and stabilize costs associated with F/A-18A inspections. Currently the AXIS is in the last stage of development with final integration expected by the end of July 1985 and production implementation by the end of the year. This paper briefly describes the equipment, and operation of the AXIS. Slides will be presented at the conference which will further illustrate the system; including inspection results

Mechanical and thermophysical properties of graphite/polyimide composite materials

Science.gov (United States)

Rummler, D. R.; Clark, R. K.

1979-01-01

An on-going program to characterize advanced composites for up to 50,000 hours of exposure to simulated supersonic cruise environments is summarized. Results are presented for up to 25,000 hours of thermal exposure and 10,000 hours of flight simulation at temperatures up to 560K (550 F) with emphasis on HTS/710 graphite/polyimide composite material. Results to date indicate that the maximum use temperature for HTS/710 may be reduced to 505K (450 F) for long-time (1000 hours) application such as the supersonic transport. Preliminary thermophysical properties data for HTS/PMR15 graphite/polyimide were generated. These data include thermal conductivity, thermal expansion, and specific heat from 115K (-252 F) to 590K (600 F) and emittance at room temperature and 590K (600 F). The purpose in generating these data was to validate use of state-of-the-art property measurement methods for advanced graphite fiber reinforced resin matrix composites. Based on results to this point, thermal expansion measurements for composites are most difficult to perform. A high degree of caution in conducting thermal expansion tests and analyzing results is required to produce reliable data.

Composite slab behavior and strength analysis under static and dynamic loads

Directory of Open Access Journals (Sweden)

Florin Radu HARIGA

2012-07-01

Full Text Available Steel-framed buildings are typically constructed using steel-deck-reinforced concrete floor slabs. The in-plane (or diaphragm strength and stiffness of the floor system are frequently utilized in the lateral load-resisting system design. This paper presents the results of an experimental research program in which four full size composite diaphragms were vertically loaded to the limit state, under static or dynamic loads. Two test specimens were provided with longitudinal steel-deck ribs, and the other two specimens with cross steel-deck ribs. Typical composite diaphragm limit states are described, and the controlling limit state for each of the full size tests is indicated. The interaction effects between the reinforced concrete slab and the steel girder on the composite slab strength and stiffness were mainly studied.

Stress wave calculations in composite plates using the fast Fourier transform.

Science.gov (United States)

Moon, F. C.

1973-01-01

The protection of composite turbine fan blades against impact forces has prompted the study of dynamic stresses in composites due to transient loads. The mathematical model treats the laminated plate as an equivalent anisotropic material. The use of Mindlin's approximate theory of crystal plates results in five two-dimensional stress waves. Three of the waves are flexural and two involve in-plane extensional strains. The initial value problem due to a transient distributed transverse force on the plate is solved using Laplace and Fourier transforms. A fast computer program for inverting the two-dimensional Fourier transform is used. Stress contours for various stresses and times after application of load are obtained for a graphite fiber-epoxy matrix composite plate. Results indicate that the points of maximum stress travel along the fiber directions.

An Achievement Degree Analysis Approach to Identifying Learning Problems in Object-Oriented Programming

Science.gov (United States)

Allinjawi, Arwa A.; Al-Nuaim, Hana A.; Krause, Paul

2014-01-01

Students often face difficulties while learning object-oriented programming (OOP) concepts. Many papers have presented various assessment methods for diagnosing learning problems to improve the teaching of programming in computer science (CS) higher education. The research presented in this article illustrates that although max-min composition is…

32 CFR 310.9 - Privacy boards and office, composition and responsibilities.

Science.gov (United States)

2010-07-01

... involving the DoD Privacy Program, meeting as necessary, to address issues of common concern so as to ensure... privacy issues relating to the Department's collection, maintenance, use, or dissemination of personal... 32 National Defense 2 2010-07-01 2010-07-01 false Privacy boards and office, composition and...

Current status and recent research achievements in SiC/SiC composites

Energy Technology Data Exchange (ETDEWEB)

Katoh, Y., E-mail: katohy@ornl.gov [Oak Ridge National Laboratory, Oak Ridge, TN (United States); Snead, L.L. [Oak Ridge National Laboratory, Oak Ridge, TN (United States); Henager, C.H. [Pacific Northwest National Laboratory, Richland, WA (United States); Nozawa, T. [Japan Atomic Energy Agency, Rokkasho, Aomori (Japan); Hinoki, T. [Institute of Advanced Energy, Kyoto University, Kyoto (Japan); Iveković, A.; Novak, S. [Jožef Stefan Institute, Ljubljana (Slovenia); Gonzalez de Vicente, S.M. [EFDA Close Support Unit, Garching (Germany)

2014-12-15

The silicon carbide fiber-reinforced silicon carbide matrix (SiC/SiC) composite system for fusion applications has seen a continual evolution from development a fundamental understanding of the material system and its behavior in a hostile irradiation environment to the current effort which is directed at a broad-based program of technology maturation program. In essence, over the past few decades this material system has steadily moved from a laboratory curiosity to an engineering material, both for fusion structural applications and other high performance application such as aerospace. This paper outlines the recent international scientific and technological achievements towards the development of SiC/SiC composite material technologies for fusion application and discusses future research directions. It also reviews the materials system in the larger context of progress to maturity as an engineering material for both the larger nuclear community and broader engineering applications.

Current status and recent research achievements in SiC/SiC composites

International Nuclear Information System (INIS)

Katoh, Y.; Snead, L.L.; Henager, C.H.; Nozawa, T.; Hinoki, T.; Iveković, A.; Novak, S.; Gonzalez de Vicente, S.M.

2014-01-01

The silicon carbide fiber-reinforced silicon carbide matrix (SiC/SiC) composite system for fusion applications has seen a continual evolution from development a fundamental understanding of the material system and its behavior in a hostile irradiation environment to the current effort which is directed at a broad-based program of technology maturation program. In essence, over the past few decades this material system has steadily moved from a laboratory curiosity to an engineering material, both for fusion structural applications and other high performance application such as aerospace. This paper outlines the recent international scientific and technological achievements towards the development of SiC/SiC composite material technologies for fusion application and discusses future research directions. It also reviews the materials system in the larger context of progress to maturity as an engineering material for both the larger nuclear community and broader engineering applications

Current status and recent research achievements in SiC/SiC composites

Science.gov (United States)

Katoh, Y.; Snead, L. L.; Henager, C. H.; Nozawa, T.; Hinoki, T.; Iveković, A.; Novak, S.; Gonzalez de Vicente, S. M.

2014-12-01

The silicon carbide fiber-reinforced silicon carbide matrix (SiC/SiC) composite system for fusion applications has seen a continual evolution from development a fundamental understanding of the material system and its behavior in a hostile irradiation environment to the current effort which is directed at a broad-based program of technology maturation program. In essence, over the past few decades this material system has steadily moved from a laboratory curiosity to an engineering material, both for fusion structural applications and other high performance application such as aerospace. This paper outlines the recent international scientific and technological achievements towards the development of SiC/SiC composite material technologies for fusion application and discusses future research directions. It also reviews the materials system in the larger context of progress to maturity as an engineering material for both the larger nuclear community and broader engineering applications.

Mechanical Behavior of Polymer Nano Bio Composite for Orthopedic Implants

Science.gov (United States)

Marimuthu, K., Dr.; Rajan, Sankar

2018-04-01

The bio-based polymer composites have been the focus of many scientific and research projects, as well as many commercial programs. In recent years, scientists and engineers have been working together to use the inherent strength and performance of the new class of bio-based composites which is compactable with human body and can act as a substitute for living cells. In this stage the polymer composites also stepped into human bone implants as a replacement for metallic implants which was problems like corrosion resistance and high cost. The polymer composite have the advantage that it can be molded to the required shape, the polymers have high corrosion resistance, less weight and low cost. The aim of this research is to develop and analyze the suitable bio compactable polymer composite for human implants. The nano particles reinforced polymer composites provides good mechanical properties and shows good tribological properties especially in the total hip and knee replacements. The graphene oxide powders are bio compactable and acts as anti biotic. GO nano powder where reinforced into High-density polyethylene in various weight percentage of 0.5% to 2%. The performance of GO nano powder shows better tribological properties. The material produced does not cause any pollution to the environment and at the same time it can be bio compactable and sustainable. The product will act environmentally friendly.

Healable Composites

Science.gov (United States)

2012-03-28

oriented fibers and healable polymer matrix 4. Laminate pre-preg layers to form composite panels with minimal voids & defects 5. Characterize the...composites: determine mechanical and crack healing properties (4, 5) Composite (3) Prepreg (2) Polymer (1) Furan (1) Maleimide Healable Composites...Develop pre-preg system of oriented fibers and healable polymer matrix 4. Laminate pre-preg layers to form composite panels with minimal voids & defects

Status and prospects for SiC-SiC composite materials development for fusion applications

International Nuclear Information System (INIS)

Sharafat, S.; Jones, R.H.; Kohyama, A.; Fenici, P.

1995-01-01

Silicon carbide (SiC) composites are very attractive for fusion applications because of their low afterheat and low activation characteristics coupled with excellent high temperature properties. These composites are relatively new materials that will require material development as well as evaluation of hermiticity, thermal conductivity, radiation stability, high temperature strength, fatigue, thermal shock, and joining techniques. The radiation stability of SiC-SiC composites is a critical aspect of their application as fusion components and recent results will be reported. Many of the non-fusion specific issues are under evaluation by other ceramic composite development programs, such as the US national continuous fiber ceramic composites.The current development status of various SiC-SiC composites research and development efforts is given. Effect of neutron irradiation on the properties of SiC-SiC composite between 500 and 1200 C are reported. Novel high temperature properties specific to ceramic matrix composite (CMC) materials are discussed. The chemical stability of SiC is reviewed briefly. Ongoing research and development efforts for joining CMC materials including SiC-SiC composites are described. In conclusion, ongoing research and development efforts show extremely promising properties and behavior for SiC-SiC composites for fusion applications. (orig.)

Advanced Industrial Materials (AIM) Program: Annual progress report FY 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-04-01

In many ways, the Advanced Industrial Materials (AIM) Program underwent a major transformation in Fiscal Year 1995 and these changes have continued to the present. When the Program was established in 1990 as the Advanced Industrial Concepts (AIC) Materials Program, the mission was to conduct applied research and development to bring materials and processing technologies from the knowledge derived from basic research to the maturity required for the end use sectors for commercialization. In 1995, the Office of Industrial Technologies (OIT) made radical changes in structure and procedures. All technology development was directed toward the seven ``Vision Industries`` that use about 80% of industrial energy and generated about 90% of industrial wastes. The mission of AIM has, therefore, changed to ``Support development and commercialization of new or improved materials to improve productivity, product quality, and energy efficiency in the major process industries.`` Though AIM remains essentially a National Laboratory Program, it is essential that each project have industrial partners, including suppliers to, and customers of, the seven industries. Now, well into FY 1996, the transition is nearly complete and the AIM Program remains reasonably healthy and productive, thanks to the superb investigators and Laboratory Program Managers. This Annual Report for FY 1995 contains the technical details of some very remarkable work by the best materials scientists and engineers in the world. Areas covered here are: advanced metals and composites; advanced ceramics and composites; polymers and biobased materials; and new materials and processes.

Re-evaluating your nuclear program needs: how to benefit from your vendor's Q.A. program

International Nuclear Information System (INIS)

Cocoros, A.E.

1979-01-01

The quality assurance component control and verification program to be presented provides a cost effective approach to monitoring and controlling the implementation of the design, fabrication, inspection and shipping plans of a supplier. It attempts to coordinate and integrate quality control and verification effort of a supplier with the control and verification effort of the purchaser to obtain a composite which accomplishes a total need. Based on the competency and capabilities of the supplier the purchaser can either maximize the effort the supplier performs or he must maximize his effort to obtain an optimum mix. The ultimate goal is to utilize the supplier's quality assurance program to the greatest benefit in assuring maximum quality

Carbon composites composites with carbon fibers, nanofibers, and nanotubes

CERN Document Server

Chung, Deborah D L

2017-01-01

Carbon Composites: Composites with Carbon Fibers, Nanofibers, and Nanotubes, Second Edition, provides the reader with information on a wide range of carbon fiber composites, including polymer-matrix, metal-matrix, carbon-matrix, ceramic-matrix and cement-matrix composites. In contrast to other books on composites, this work emphasizes materials rather than mechanics. This emphasis reflects the key role of materials science and engineering in the development of composite materials. The applications focus of the book covers both the developing range of structural applications for carbon fiber composites, including military and civil aircraft, automobiles and construction, and non-structural applications, including electromagnetic shielding, sensing/monitoring, vibration damping, energy storage, energy generation, and deicing. In addition to these new application areas, new material in this updated edition includes coverage of cement-matrix composites, carbon nanofibers, carbon matrix precursors, fiber surface ...

Kinetic model for predicting the composition of chlorinated water discharged from power plant cooling systems

International Nuclear Information System (INIS)

Lietzke, M.H.

1977-01-01

A kinetic model for predicting the composition of chlorinated water discharged from power plant cooling systems has been developed. The model incorporates the most important chemical reactions that are known to occur when chlorine is added to natural fresh waters. The simultaneous differential equations, which describe the rates of these chemical reactions, are solved numerically to give the composition of the water as a function of time. A listing of the computer program is included, along with a description of the input variables. A worked-out example illustrates the application of the program to an actual cooling system. An appendix contains a compilation of the known equilibrium and kinetic data for many of the chemical reactions that might be encountered in chlorinating natural fresh waters

Radiation curable adhesive compositions and composite structures

International Nuclear Information System (INIS)

Brenner, W.

1984-01-01

This disclosure relates to novel adhesive compositions and composite structures utilizing the same, wherein said adhesive compositions contain an elastomer, a chemically compatible ethylenically unsaturated monomer, a tackifier, an adhesion promoter, and optionally, pigments, fillers, thickeners and flow control agents which are converted from the liquid to the solid state by exposure to high energy ionizing radiation such as electron beam. A particularly useful application for such adhesive compositions comprises the assembly of certain composite structures or laminates consisting of, for example, a fiber flocked rubber sheet and a metal base with the adhesive fulfilling the multiple functions of adhering the flocked fiber to the rubber sheet as well as adhering the rubber sheet to the metal base. Optionally, the rubber sheet itself may also be cured at the same time as the adhesive composition with all operations being carried out at ambient temperatures and in the presence of air, with exposure of said assembly to selected dosages of high energy ionizing radiation. These adhesive compositions contain no solvents thereby almost eliminating air pollution or solvent toxicity problems, and offer substantial savings in energy and labor as they are capable of curing in very short time periods without the use of external heat which might damage the substrate

The Manufacturing Process for the NASA Composite Crew Module Demonstration Structure

Science.gov (United States)

Pelham, Larry; Higgins, John E.

2008-01-01

This paper will describe the approaches and methods selected in fabrication of a carbon composite demonstration structure for the Composite Crew Module (CCM) Program. The program is managed by the NASA Safety and Engineering Center with participants from ten NASA Centers and AFRL. Multiple aerospace contractors are participating in the design development, tooling and fabrication effort as well. The goal of the program is to develop an agency wide design team for composite habitable spacecraft. The specific goals for this development project are: a).To gain hands on experience in design, building and testing a composite crew module. b) To validate key assumptions by resolving composite spacecraft design details through fabrication and testing of hardware. This abstract is based on Preliminary Design data..The final design will continue to evolve through the fall of 2007 with fabrication mostly completed by conference date. From a structures perspective, the.CCM can be viewed as a pressure module with variable pressure time histories and a series of both impact and quasi-static, high intensity point, line, and area distributed loads. The portion of the overall space vehicle being designed and. fabricated by the CCM team is just the pressure module and primary loading points. The heaviest point loads are applied and distributed to the pressure module at.an aluminum Service Module/Alternate Launch Abort System (SM/ALAS) fittings and at Main and Drogue Chute fittings. Significant line loads with metal to metal impact is applied at.the Lids ring. These major external point and line loads as well as pressure impact loads (blast and water landing) are applied to the lobed floor though the reentry shield and crushable materials. The pressure module is divided into upper and lower. shells that mate together with a bonded belly band splice joint to create the completed structural assembly. The benefits of a split CCM far outweigh the risks of a joint. These benefits include

Exercise program improved subjective dry eye symptoms for office workers.

Science.gov (United States)

Sano, Kokoro; Kawashima, Motoko; Takechi, Sayuri; Mimura, Masaru; Tsubota, Kazuo

2018-01-01

We investigated the benefits of a cognitive behavior therapy-based exercise program to reduce the dry eye symptoms of office workers. We recruited 11 office workers with dry eye symptoms, aged 31-64 years, who voluntarily participated in group health guidance at a manufacturing company. Participants learned about the role of physical activity and exercise in enhancing wellness and performed an exercise program at home 3 days per week for 10 weeks. We estimated the indexes of body composition, dry eye symptoms, and psychological distress using the Dry Eye-Related Quality of Life Score and the World Health Organization's Subjective Well-Being Inventory questionnaires pre- and postintervention. The 10-week exercise program and the questionnaires were completed by 48.1% (39 of 81) of the participants. Body composition did not change pre- and postintervention. However, the average of the Dry Eye-Related Quality of Life Score scores in participants with subjective dry eye significantly improved after the intervention. Moreover, the World Health Organization's Subjective Well-Being Inventory positive well-being score tended to increase after the intervention. In this study, we showed that a 10-week exercise program improved subjective dry eye symptoms of healthy office workers. Our study suggests that a cognitive behavior therapy-based exercise program can play an important role in the treatment of patients with dry eye disease.

Data-driven weights and restrictions in the construction of composite indicators

Directory of Open Access Journals (Sweden)

Ana Perišić

2015-03-01

Full Text Available Composite indicators are increasingly recognized as a useful tool in policy analysis and public communication. However, if poorly constructed, they can send misleading policy messages. Perhaps the most difficult aspect of constructing a composite indicator is choosing weights for the components. The categorization of Croatian territorial units for development policy is based on the value of the composite indicator called the development index. The main goal of this paper is to propose an empirical approach for weight selection. In order to generate the set of non-subjective weights, principal component analysis and linear programming methods have been applied. An application of data envelopment analysis to the field of composite indicators, known as the Benefit-of-the-Doubt approach, has been demonstrated subject to proportional sub-indicator share restrictions. Additionally, the Monte Carlo simulation of weights was conducted, and confidence intervals for the values of the development index were estimated. Owing to the fact that the examined weighting schemes have resulted in the different categorization of territorial units, use of unit-specific weights and incorporating uncertainty in the construction of a composite indicator looks promising for further work.

Computer program for buckling loads of orthotropic laminated stiffened panels subjected to biaxial in-place loads (BUCLASP 2)

Science.gov (United States)

Viswanathan, A. V.; Tamekuni, M.

1974-01-01

General-purpose program performs exact instability analyses for structures such as unidirectionally-stiffened, rectangular composite panels. Program was written in FORTRAN IV and COMPASS for CDC-series computers.

The Benefits of High Intensity Functional Training (HIFT) Fitness Programs for Military Personnel

Science.gov (United States)

Haddock, Christopher K.; Poston, Walker S.C.; Heinrich, Katie M.; Jahnke, Sara A.; Jitnarin, Nattinee

2016-01-01

High intensity functional training (HIFT) programs are designed to address multiple fitness domains, potentially providing improved physical and mental readiness in a changing operational environment. Programs consistent with HIFT principals such as CrossFit, SEALFIT and the US Marine Corps’ High Intensity Tactical Training (HITT) program are increasingly popular among military personnel. This article reviews the practical, health, body composition, and military fitness implications of HIFT exercise programs. We conclude that, given the unique benefits of HIFT, the military should consider evaluating whether these programs should be the standard for military fitness training. PMID:27849484

Portfolio optimization in enhanced index tracking with goal programming approach

Science.gov (United States)

Siew, Lam Weng; Jaaman, Saiful Hafizah Hj.; Ismail, Hamizun bin

2014-09-01

Enhanced index tracking is a popular form of passive fund management in stock market. Enhanced index tracking aims to generate excess return over the return achieved by the market index without purchasing all of the stocks that make up the index. This can be done by establishing an optimal portfolio to maximize the mean return and minimize the risk. The objective of this paper is to determine the portfolio composition and performance using goal programming approach in enhanced index tracking and comparing it to the market index. Goal programming is a branch of multi-objective optimization which can handle decision problems that involve two different goals in enhanced index tracking, a trade-off between maximizing the mean return and minimizing the risk. The results of this study show that the optimal portfolio with goal programming approach is able to outperform the Malaysia market index which is FTSE Bursa Malaysia Kuala Lumpur Composite Index because of higher mean return and lower risk without purchasing all the stocks in the market index.

Sandia Laboratories environment and safety programs

International Nuclear Information System (INIS)

Zak, B.D.; McGrath, P.E.; Trauth, C.A. Jr.

1975-01-01

Sandia, one of ERDA's largest laboratories, is primarily known for its extensive work in the nuclear weapons field. In recent years, however, Sandia's role has expanded to embrace sizeable programs in the energy, resource recovery, and the environment and safety fields. In this latter area, Sandia has programs which address nuclear, fossil fuel, and general environment and safety issues. Here we survey ongoing activities and describe in more detail aa few projects of particular interest. These range from a study of the impact of sealed disposal of radioactive wastes, through reactor safety and fossil fuel plume chemistry, to investigations of the composition and dynamics of the stratosphere

Conversation at a Crucial Moment: Hybrid Courses and the Future of Writing Programs

Science.gov (United States)

Gouge, Catherine

2009-01-01

Because hybrid first-year college writing programs are an emerging phenomenon, it is important for composition specialists to identify their potential strengths and possible disadvantages. The author reviews the various forms that such programs have taken so far, and she engages in an extended critique of one particular institution's model,…

Making of composite type energy introduction models in cities; Toshi ni okeru fukugogata energy donyu model no sakusei

Energy Technology Data Exchange (ETDEWEB)

NONE

1997-03-01

The paper made and studied simulation models in case of introducing new energy of composite type to cities. In the study, using a standard composition unit of city as a cluster, the compositional element was divided into 25 cells, which were divided into the residence superiority cell and the business superiority cell. The residence superiority cell was divided into highrise and lowrise. The calculation program is to simulate effects of introducing new energy such as the photovoltaic power generation, solar energy utilization, waste power generation, cogeneration, and unused energy like river water and waste water. Using the program, the analysis of sensitivity was conducted concerning how the outputs will change according to differences in energy consuming composition in the urban area. The calculation was conducted concerning local cities of the warm area, local cities of the cold area, local cities of the subtropical area, residence/working-place neighboring core cities in the warm area, central areas of large cities of the warm area, and new towns of the warm area. 28 figs., 27 tabs.

24 CFR 982.516 - Family income and composition: Regular and interim examinations.

Science.gov (United States)

2010-04-01

... VOUCHER PROGRAM Rent and Housing Assistance Payment § 982.516 Family income and composition: Regular and... assistance payment. (For a voucher tenancy, the housing assistance payment shall be calculated in accordance... the housing assistance payment resulting from an interim redetermination. (2) At the effective date of...

TROPOSPHERIC AEROSOL PROGRAM, PROGRAM PLAN, MARCH 2001

Energy Technology Data Exchange (ETDEWEB)

SCHWARTZ,S.E.; LUNN,P.

2001-03-01

The goal of Tropospheric Aerosol Program (TAP) will be to develop the fundamental scientific understanding required to construct tools for simulating the life cycle of tropospheric aerosols--the processes controlling their mass loading, composition, and microphysical properties, all as a function of time, location, and altitude. The TAP approach to achieving this goal will be by conducting closely linked field, modeling, laboratory, and theoretical studies focused on the processes controlling formation, growth, transport, and deposition of tropospheric aerosols. This understanding will be represented in models suitable for describing these processes on a variety of geographical scales; evaluation of these models will be a key component of TAP field activities. In carrying out these tasks TAP will work closely with other programs in DOE and in other Federal and state agencies, and with the private sector. A forum to directly work with our counterparts in industry to ensure that the results of this research are translated into products that are useful to that community will be provided by NARSTO (formerly the North American Research Strategy on Tropospheric Ozone), a public/private partnership, whose membership spans government, the utilities, industry, and university researchers in Mexico, the US, and Canada.

Energy Efficiency and Renewable Energy Program. Bibliography, 1993 edition

Energy Technology Data Exchange (ETDEWEB)

Vaughan, K.H.

1993-06-01

The Bibliography contains listings of publicly available reports, journal articles, and published conference papers sponsored by the DOE Office of Energy Efficiency and Renewable Energy and published between 1987 and mid-1993. The topics of Bibliography include: analysis and evaluation; building equipment research; building thermal envelope systems and materials; district heating; residential and commercial conservation program; weatherization assistance program; existing buildings research program; ceramic technology project; alternative fuels and propulsion technology; microemulsion fuels; industrial chemical heat pumps; materials for advanced industrial heat exchangers; advanced industrial materials; tribology; energy-related inventions program; electric energy systems; superconducting technology program for electric energy systems; thermal energy storage; biofuels feedstock development; biotechnology; continuous chromatography in multicomponent separations; sensors for electrolytic cells; hydropower environmental mitigation; environmental control technology; continuous fiber ceramic composite technology.

Chemical composition and strength of dolomite geopolymer composites

Science.gov (United States)

Aizat, E. A.; Al Bakri, A. M. M.; Liew, Y. M.; Heah, C. Y.

2017-09-01

The chemical composition of dolomite and the compressive strength of dolomite geopolymer composites were studied. The both composites prepared with mechanical mixer manufactured by with rotor speed of 350 rpm and curing in the oven for 24 hours at 80˚C. XRF analysis showThe dolomite raw materials contain fewer amounts of Si and Al but high Ca in its composition. Dolomite geopolymer composites with 20M of NaOH shows greater and optimum compressive strength compared to dolomite geopolymer with other NaOH molarity. This indicated better interaction of dolomite raw material and alkaline activator need high molarity of NaOH in order to increase the reactivity of dolomite.

Wood-based composite materials : panel products, glued-laminated timber, structural composite lumber, and wood-nonwood composite materials

Science.gov (United States)

Nicole M. Stark; Zhiyong Cai; Charles Carll

2010-01-01

This chapter gives an overview of the general types and composition of wood-based composite products and the materials and processes used to manufacture them. It describes conventional wood-based composite panels and structural composite materials intended for general construction, interior use, or both. This chapter also describes wood–nonwood composites. Mechanical...

Ion beam studies. Part 5 - the computer simulation of composite ion implantation profiles

International Nuclear Information System (INIS)

Freeman, J.H.; Booker, D.V.

1977-01-01

The computer simulation of composite ion implantation profiles produced by continuous energy programming and by discrete multiple dose doping is described. It is shown that precise matching of the computed profile to various uniform and power-law distributions can be achieved. (author)

Impact of a 12-week high-intensity interval training without caloric restriction on body composition and lipid profile in sedentary healthy overweight/obese youth.

Science.gov (United States)

Khammassi, Marwa; Ouerghi, Nejmeddine; Hadj-Taieb, Sameh; Feki, Moncef; Thivel, David; Bouassida, Anissa

2018-02-01

Although High-intensity interval training (HIIT) has shown its effectiveness in improving body composition, cardio-respiratory fitness and lipid profile in obese adults, evidences remain limited in overweight/obese youth. This study was conducted to investigate the effect of a 12-week HIIT program without caloric restriction on body composition and lipid profile among young overweight/obese men. Twenty healthy obese youth were randomly allocated into two groups; experimental group (HIIT) and control group. The HIIT program consisted in 3 exercises sessions per week (30 sec of work at 100% maximal aerobic velocity [MAV]) interspersed by 30 sec of active recovery at 50% MAV, starting by 15 repetitions to reach 27 by the end of the program. Aerobic capacity (MAV and maximum oxygen uptake [VO2max]), body composition (body mass index [BMI], waist circumference [WC], and fat mass percent) and lipid profile (triglycerides [TG] and total, high-density lipoprotein [HDL] and low-density lipoprotein [LDL] cholesterol) were determined before and after the HIIT program. Following 12 weeks of HIIT, WC, BMI ( P HIIT group, only. Total cholesterol ( P HIIT group, while LDL and HDL cholesterol levels remained unchanged in both groups. HIIT may be particularly useful in overweight/obese youth to improve body composition, aerobic fitness and lipid profile.

Advanced composite structural concepts and material technologies for primary aircraft structures

Science.gov (United States)

Jackson, Anthony

1991-01-01

Structural weight savings using advanced composites have been demonstrated for many years. Most military aircraft today use these materials extensively and Europe has taken the lead in their use in commercial aircraft primary structures. A major inhibiter to the use of advanced composites in the United States is cost. Material costs are high and will remain high relative to aluminum. The key therefore lies in the significant reduction in fabrication and assembly costs. The largest cost in most structures today is assembly. As part of the NASA Advanced Composite Technology Program, Lockheed Aeronautical Systems Company has a contract to explore and develop advanced structural and manufacturing concepts using advanced composites for transport aircraft. Wing and fuselage concepts and related trade studies are discussed. These concepts are intended to lower cost and weight through the use of innovative material forms, processes, structural configurations and minimization of parts. The approach to the trade studies and the downselect to the primary wing and fuselage concepts is detailed. The expectations for the development of these concepts is reviewed.

NEOShield-2 Project: Final Results on Compositional Characterization of small NEOs

Science.gov (United States)

Barucci, Maria Antonieta; Perna, Davide; Fornasier, Sonia; Doressoundiram, Alain; Lantz, Cateline; Popescu, Marcel; Merlin, Frederic; Fulchignoni, Marcello

2017-10-01

NEOShield-2 project was selected in the framework of the European Commission H2020 program in answer to the call for “Access technologies and characterisation for Near Earth Objects (NEOs)”. NEOShield-2 project (2015-2017) is a follow-up of the first NEOShield (2012-2015) and includes 11 European Institutions and Industries. The main objectives of NEOShield-2 project are: i) technological development on techniques and instruments needed for GNC for possible asteroid missions and ii) characterization of NEOs of small sizes.Our team at LESIA is the leader of the entire observational program which involved complementary techniques to provide physical and compositional characterization of NEOs. Priority has been given to potential space-mission targets, optimized for mitigation or exploration missions. In this framework an agreement with the European Southern Observatory was signed to obtain Guaranteed Time Observations at the 3.6-meter NTT with an allocation of 30 nights to characterize by spectroscopy the composition of the smaller asteroids. The objects with an absolute magnitude larger than 20 were selected, with a priority for the very small newly discovered objects.We obtained more than 170 new spectra of NEOs. The observations were performed with EFOSC2 instrument. We covered the wavelength interval 0.4-0.92 microns, with a resolution of R=~200. The observed asteroids include 29 asteroids with diameters smaller than 100 meters and 71 with diameters between 100 and 300 m.The taxonomic type has been assigned for 137 individual objects. Our results on NEO mineralogical compositions provide a body of reference data directly applicable to the design and development of mitigation-relevant space missions. Within our survey, we found eight D-types with ΔV funding by European Commission Horizon 2020 program (contract No. PROTEC-2-2014-640351).

Composite Materials

DEFF Research Database (Denmark)

Nielsen, Lauge Fuglsang

This book deals with the mechanical and physical behavior of composites as influenced by composite geometry. "Composite Materials" provides a comprehensive introduction for researchers and students to modern composite materials research with a special emphasis on the significance of phase geometry......, viscoelastic behavior, and internal stress states. Other physical properties considered are thermal and electrical conductivities, diffusion coefficients, dielectric constants and magnetic permeability. Special attention is given to the effect of pore shape on the mechanical and physical behavior of porous....... The book enables the reader to a better understanding of the behavior of natural composites, improvement of such materials, and design of new materials with prescribed properties. A number of examples are presented: Special composite properties considered are stiffness, shrinkage, hygro-thermal behavior...

The effects of an individualized exercise intervention on body composition in breast cancer patients undergoing treatment

OpenAIRE

Battaglini,Claudio; Bottaro,Martim; Dennehy,Carolyn; Rae,Logan; Shields,Edgar; Kirk,David; Hackney,Anthony

2007-01-01

CONTEXT AND OBJECTIVE: Changes in metabolism have been reported in the majority of patients undergoing cancer treatment, and these are usually characterized by progressive change in body composition. The effects of aerobic exercise programs to combat the cancer and cancer treatment-related side effects, which include the negative changes in body composition, have been extensively reported in the literature. However, few resistance exercise intervention studies have hypothesized that breast ca...

Metallic composite materials

International Nuclear Information System (INIS)

Frommeyer, G.

1987-01-01

The structure and properties of metallic composite materials and composite materials with metallic matrix are considered. In agreement with the morphology of constituent phases the following types of composite materials are described: dispersion-strengthened composite materials; particle-reinforced composite materials; fibrous composite materials; laminar composite materials. Data on strength and electric properties of the above-mentioned materials, as well as effect of the amount, location and geometric shape of the second phase on them, are presented

Winding of fibre composites; Vikling af fiberkompositter

Energy Technology Data Exchange (ETDEWEB)

Lystrup, Aage

2006-01-01

Within the project 'Storage of hydrogen in advanced high pressure vessels' under the PSO-R AND D 2005 program one of the tasks is to describe the technology, which is used for manufacturing of fibre reinforced pressure vessels. Fibre reinforced pressure vessels for high pressures are manufactured by winding structural load bearing fibres around a mandrel or an internal liner. There are two different types of cylindrical pressure vessels: 1) Cylinders with thick metal liner, where only the cylindrical part is over wrapped with hoop windings, and 2) cylinders with a thin metal or polymer liner, where both the cylindrical part and the end domes are over wrapped with more layers with different fibre orientations (helical and hoop windings). This report describes the fundamental principles for filament winding of fibre reinforced polymer composites. After a short introduction to the advanced fibre composites, their properties and semi-raw materials used for fibre composites, the focus is on the process parameters, which have influence on the material quality of filament wound components. The report is both covering winding of fibre reinforced thermo-setting polymers as well as thermoplastic polymers, and there are references to vendors of filament winding machines, accessory equipment and computer software for design and manufacturing of filament wound components. (au)

Fermentation based carbon nanotube multifunctional bionic composites

Science.gov (United States)

Valentini, Luca; Bon, Silvia Bittolo; Signetti, Stefano; Tripathi, Manoj; Iacob, Erica; Pugno, Nicola M.

2016-06-01

The exploitation of the processes used by microorganisms to digest nutrients for their growth can be a viable method for the formation of a wide range of so called biogenic materials that have unique properties that are not produced by abiotic processes. Here we produced living hybrid materials by giving to unicellular organisms the nutrient to grow. Based on bread fermentation, a bionic composite made of carbon nanotubes (CNTs) and a single-cell fungi, the Saccharomyces cerevisiae yeast extract, was prepared by fermentation of such microorganisms at room temperature. Scanning electron microscopy analysis suggests that the CNTs were internalized by the cell after fermentation bridging the cells. Tensile tests on dried composite films have been rationalized in terms of a CNT cell bridging mechanism where the strongly enhanced strength of the composite is governed by the adhesion energy between the bridging carbon nanotubes and the matrix. The addition of CNTs also significantly improved the electrical conductivity along with a higher photoconductive activity. The proposed process could lead to the development of more complex and interactive structures programmed to self-assemble into specific patterns, such as those on strain or light sensors that could sense damage or convert light stimulus in an electrical signal.

Differences in interfacial bond strengths of graphite fiber-epoxy resin composites

Science.gov (United States)

Needles, H. L.

1985-01-01

The effect of epoxy-size and degree of cure on the interfacial bonding of an epoxy-amine-graphite fiber composite system is examined. The role of the fiber-resin interface in determining the overall mechanical properties of composites is poorly understood. A good interfacial adhesive bond is required to achieve maximum stress transfer to the fibers in composites, but at the same time some form of energy absorbing interfacial interaction is needed to achieve high fracture toughening. The incompatibility of these two processes makes it important to understand the nature and basic factors involved at the fiber-resin interface as stress is applied. The mechanical properties including interlaminar shear values for graphite fiber-resin composites are low compared to glass and boron-resin composites. These differences have been attributed to poor fiber-matrix adhesion. Graphite fibers are commonly subjected to post-treatments including application of organic sizing in order to improve their compatibility with the resin matrix and to protect the fiber tow from damage during processing and lay-up. In such processes, sized graphite fiber tow is impregnated with epoxy resin and then layed-up i nto the appropriate configuration. Following an extended ambient temperature cure, the graphite-resin composite structure is cured at elevated temperature using a programmed temperature sequence to cure and then cool the product.

Edge delamination of composite laminates subject to combined tension and torsional loading

Science.gov (United States)

Hooper, Steven J.

1990-01-01

Delamination is a common failure mode of laminated composite materials. Edge delamination is important since it results in reduced stiffness and strength of the laminate. The tension/torsion load condition is of particular significance to the structural integrity of composite helicopter rotor systems. Material coupons can easily be tested under this type of loading in servo-hydraulic tension/torsion test stands using techniques very similar to those used for the Edge Delamination Tensile Test (EDT) delamination specimen. Edge delamination of specimens loaded in tension was successfully analyzed by several investigators using both classical laminate theory and quasi-three dimensional (Q3D) finite element techniques. The former analysis technique can be used to predict the total strain energy release rate, while the latter technique enables the calculation of the mixed-mode strain energy release rates. The Q3D analysis is very efficient since it produces a three-dimensional solution to a two-dimensional domain. A computer program was developed which generates PATRAN commands to generate the finite element model. PATRAN is a pre- and post-processor which is commonly used with a variety of finite element programs such as MCS/NASTRAN. The program creates a sufficiently dense mesh at the delamination crack tips to support a mixed-mode fracture mechanics analysis. The program creates a coarse mesh in those regions where the gradients in the stress field are low (away from the delamination regions). A transition mesh is defined between these regions. This program is capable of generating a mesh for an arbitrarily oriented matrix crack. This program significantly reduces the modeling time required to generate these finite element meshes, thus providing a realistic tool with which to investigate the tension torsion problem.

Wood composites

Science.gov (United States)

Lars Berglund; Roger M. Rowell

2005-01-01

A composite can be defined as two or more elements held together by a matrix. By this definition, what we call “solid wood” is a composite. Solid wood is a three-dimensional composite composed of cellulose, hemicelluloses and lignin (with smaller amounts of inorganics and extractives), held together by a lignin matrix. The advantages of developing wood composites are (...

BlenX-based compositional modeling of complex reaction mechanisms

Directory of Open Access Journals (Sweden)

Judit Zámborszky

2010-02-01

Full Text Available Molecular interactions are wired in a fascinating way resulting in complex behavior of biological systems. Theoretical modeling provides a useful framework for understanding the dynamics and the function of such networks. The complexity of the biological networks calls for conceptual tools that manage the combinatorial explosion of the set of possible interactions. A suitable conceptual tool to attack complexity is compositionality, already successfully used in the process algebra field to model computer systems. We rely on the BlenX programming language, originated by the beta-binders process calculus, to specify and simulate high-level descriptions of biological circuits. The Gillespie's stochastic framework of BlenX requires the decomposition of phenomenological functions into basic elementary reactions. Systematic unpacking of complex reaction mechanisms into BlenX templates is shown in this study. The estimation/derivation of missing parameters and the challenges emerging from compositional model building in stochastic process algebras are discussed. A biological example on circadian clock is presented as a case study of BlenX compositionality.

Carbide coated fibers in graphite-aluminum composites

Science.gov (United States)

Imprescia, R. J.; Levinson, L. S.; Reiswig, R. D.; Wallace, T. C.; Williams, J. M.

1975-01-01

The NASA-supported program at the Los Alamos Scientific Laboratory (LASL) to develop carbon fiber-aluminum matrix composites is described. Chemical vapor deposition (CVD) was used to uniformly deposit thin, smooth, continuous coats of TiC on the fibers of graphite tows. Wet chemical coating of fibers, followed by high-temperature treatment, was also used, but showed little promise as an alternative coating method. Strength measurements on CVD coated fiber tows showed that thin carbide coats can add to fiber strength. The ability of aluminum alloys to wet TiC was successfully demonstrated using TiC-coated graphite surfaces. Pressure-infiltration of TiC- and ZrC-coated fiber tows with aluminum alloys was only partially successful. Experiments were performed to evaluate the effectiveness of carbide coats on carbon as barriers to prevent reaction between alluminum alloys and carbon. Initial results indicate that composites of aluminum and carbide-coated graphite are stable for long periods of time at temperatures near the alloy solidus.

Effects of CFRP Strengthening on Dynamic and Fatigue Responses of Composite Bridge

Directory of Open Access Journals (Sweden)

Kittisak Kuntiyawichai

2014-01-01

Full Text Available This paper investigates the effect of CFRP strengthening on dynamic and fatigue responses of composite bridge using finite element program ABAQUS. Dynamic and fatigue responses of composite bridge due to truck load based on AASHTO standard are investigated. Two types of CFRP strengthening techniques, CFRP sheets and CFRP deck, are applied to both the damaged and undamaged bridges. For the case of damaged bridge, two through-thickness crack sizes, 3 mm and 6 mm in depth, are assumed at midspan of the steel girders. Furthermore, effects of the number of steel girders on the dynamic and fatigue responses are also considered. The results show that the maximum responses of composite bridges occur for dual lane cases. By using CFRP as a strengthening material, the maximum stress and deflection of the steel girders reduce and consequently increase the fatigue life of the girders. After introducing initial crack into the steel girders of the composite bridges, the fatigue life of the bridges is dramatically reduced. However, the overall performance of the damaged composite bridge can be improved by using CFRP, albeit with less effectiveness. Therefore, if cracks are found, steel welding must be performed before strengthening the composite bridge by CFRP.

Humidity Effects on Soluble Core Mechanical and Thermal Properties (Polyvinyl Alcohol/Microballoon Composite)

Science.gov (United States)

1993-01-01

This document constitutes the final report for the study of humidity effects and loading rate on soluble core (PVA/MB composite material) mechanical and thermal properties. This report describes test results, procedures employed, and any unusual occurrences or specific observations associated with this test program.

Composite fuselage crown panel manufacturing technology

Science.gov (United States)

Willden, Kurtis; Metschan, S.; Grant, C.; Brown, T.

1992-01-01

Commercial fuselage structures contain significant challenges in attempting to save manufacturing costs with advanced composite technology. Assembly issues, material costs, and fabrication of elements with complex geometry are each expected to drive the cost of composite fuselage structures. Boeing's efforts under the NASA ACT program have pursued key technologies for low-cost, large crown panel fabrication. An intricate bond panel design and manufacturing concepts were selected based on the efforts of the Design Build Team (DBT). The manufacturing processes selected for the intricate bond design include multiple large panel fabrication with the Advanced Tow Placement (ATP) process, innovative cure tooling concepts, resin transfer molding of long fuselage frames, and utilization of low-cost material forms. The process optimization for final design/manufacturing configuration included factory simulations and hardware demonstrations. These efforts and other optimization tasks were instrumental in reducing cost by 18 percent and weight by 45 percent relative to an aluminum baseline. The qualitative and quantitative results of the manufacturing demonstrations were used to assess manufacturing risks and technology readiness.

The use of image analysis for the study of interfacial bonding in solid composite propellant

Directory of Open Access Journals (Sweden)

JASMINA DOSTANIC

2007-10-01

Full Text Available In the framework of this research, the program Image Pro Plus was applied for determining the polymer–oxidizer interactions in HTPB-based composite propellants. In order to improve the interactions, different bonding agents were used, and their efficiency was analyzed. The determination of the quantity, area and radius of non-bonded oxidizer crystals is presented. The position of formed cracks in the specimen and their area has a great influence on the mechanical properties of composite propellant. The preparation of the composite propellant in order to enable the photographing of their structure by means of stereoscopic and metallographic microscopes with the digital camera is also described as well.

A revolutionary approach to composite construction and flight management systems for small, general aviation airplanes

Science.gov (United States)

Roskam, Jan; Wenninger, ED

1992-01-01

The design studies for two composite general aviation airplanes are presented. The main consideration for both of the designs was to avoid the typical 'metal replacement' philosophy that has hindered the widespread use of composites in general aviation aircraft. The first design is for a low wing aircraft based on the Smith Aircraft Corporation GT-3 Global Trainer. The second aircraft is a composite version of the Cessna 152. The project was conducted as a graduate level design class under the auspices of the KU/NASA/USRA Advanced Design Program in aeronautics. The results obtained from the Fall semester of 1991 and the Spring semester of 1992 are presented.

Prediction of Protein Submitochondrial Locations by Incorporating Dipeptide Composition into Chou's General Pseudo Amino Acid Composition.

Science.gov (United States)

Ahmad, Khurshid; Waris, Muhammad; Hayat, Maqsood

2016-06-01

Mitochondrion is the key organelle of eukaryotic cell, which provides energy for cellular activities. Submitochondrial locations of proteins play crucial role in understanding different biological processes such as energy metabolism, program cell death, and ionic homeostasis. Prediction of submitochondrial locations through conventional methods are expensive and time consuming because of the large number of protein sequences generated in the last few decades. Therefore, it is intensively desired to establish an automated model for identification of submitochondrial locations of proteins. In this regard, the current study is initiated to develop a fast, reliable, and accurate computational model. Various feature extraction methods such as dipeptide composition (DPC), Split Amino Acid Composition, and Composition and Translation were utilized. In order to overcome the issue of biasness, oversampling technique SMOTE was applied to balance the datasets. Several classification learners including K-Nearest Neighbor, Probabilistic Neural Network, and support vector machine (SVM) are used. Jackknife test is applied to assess the performance of classification algorithms using two benchmark datasets. Among various classification algorithms, SVM achieved the highest success rates in conjunction with the condensed feature space of DPC, which are 95.20 % accuracy on dataset SML3-317 and 95.11 % on dataset SML3-983. The empirical results revealed that our proposed model obtained the highest results so far in the literatures. It is anticipated that our proposed model might be useful for future studies.

Commentary on the Canadian nuclear fuel waste management program

International Nuclear Information System (INIS)

Sheng, G.; Shemilt, L.W.

1981-01-01

A summary of the first formal review of the Technical Advisory Committee (TAC) to Atomic Energy of Canada Limited on the Nuclear Fuel Waste Management Program is presented. The Program is described briefly and the composition and role of TAC in relation to the Program is outlined. Salient points and major recommendations are presented from the First Annual Report of TAC in which geoscience aspects of the Program were emphasized. It is the view of the Committee that overall, the whole Waste Management Program is well conceived, that there are many impressive accomplishments of high quality, that detailed research objectives are becoming more clearly delineated, that there is growing clarification as to the most critical areas in which research needs to be accomplished and that the increasing participation by university and industry scientists and engineers is reassuring

The Navy/NASA Engine Program (NNEP89): Interfacing the program for the calculation of complex Chemical Equilibrium Compositions (CEC)

Science.gov (United States)

Gordon, Sanford

1991-01-01

The NNEP is a general computer program for calculating aircraft engine performance. NNEP has been used extensively to calculate the design and off-design (matched) performance of a broad range of turbine engines, ranging from subsonic turboprops to variable cycle engines for supersonic transports. Recently, however, there has been increased interest in applications for which NNEP is not capable of simulating, such as the use of alternate fuels including cryogenic fuels and the inclusion of chemical dissociation effects at high temperatures. To overcome these limitations, NNEP was extended by including a general chemical equilibrium method. This permits consideration of any propellant system and the calculation of performance with dissociation effects. The new extended program is referred to as NNEP89.

Thermospheric Density and Composition: an Integrated Research Approach

Science.gov (United States)

Richmond, A. D.; Akmaev, R.; Anderson, P. C.; Crowley, G.; Drob, D. P.; Lummerzheim, D.; Solomon, S. C.; Tobiska, W.

2006-12-01

The thermosphere, at altitudes of approximately 90-500 km, affects human technological systems through the drag it exerts on low-Earth-orbit spacecraft and debris, and through its influence on the embedded ionosphere, affecting radio-wave transmissions, and, consequently, communications and geolocation. We have formed a team under the NASA Living With a Star Targeted Research and Technology program to carry out an integrated research program on the focused science topic of thermospheric density and composition. Our goal is to improve scientific understanding of the thermosphere-ionosphere system, leading to improved first-principles models that accurately specify the variations of thermospheric density and composition with latitude, longitude, local time, solar flux, season, magnetic activity level, and orientation of the interplanetary magnetic field. We are developing improved quantitative models of solar and magnetospheric inputs to the thermosphere and improved physical parameterizations in the first-principles global models; we are analyzing thermospheric responses to solar and magnetospheric inputs on time scales from minutes to the length of the solar cycle; and we are developing an improved empirical model of thermospheric winds. These research products will be made available to the scientific community. This work is helping to clarify critical problem areas in thermospheric physics for planned NASA missions like the Ionosphere-Thermosphere Storm Probes, Geospace Electrodynamics Connections, and the Global-scale Observation of the Limb and Disk.

Four families of composite quarks and leptons

International Nuclear Information System (INIS)

Albright, C.H.; Northern Illinois Univ., De Kalb; Schrempp, B.; Schrempp, F.

1982-03-01

Four families of composite quarks and leptons, two standard and two non-standard, are found in a unique solution SU(3)sub(H)sub(C) x SU(6)sub(R) of a restricted 't Hooft anomaly-matching program. Testable predictions emerge, such as prohibition of μ → eγ, zero charge asymmetry in e + e - → tau + tau - in contrast to e + e - → μ + μ - , and a rich new hadron spectrum with masses around Msub(W). A minimal set of spectator fermions contains color-singlet objects with fractional quark-like charges. (orig.)

Twin study of genetic and environmental influences on adult body size, shape and composition

DEFF Research Database (Denmark)

Schousboe, K.; Visscher, P.M.; Erbas, B.

2004-01-01

), we determined zygosity by DNA similarity, and performed anthropometry and bioelectrical impedance analysis of body composition. The contribution to the total phenotypic variance of genetic, common environment, and individual environment was estimated in multivariate analysis using the FISHER program...... effects under the assumptions of no nonadditive effect. The pattern of age trends was inconsistent. However, when significant there was a decrease in heritability with advancing age. DISCUSSION: These findings suggest that adult body size, shape, and composition are highly heritable in both women and men...

Process-aware web programming with Jolie

DEFF Research Database (Denmark)

Montesi, F.

2016-01-01

We extend the Jolie programming language to capture the native modelling of process-aware web information systems, i.e., web information systems based upon the execution of business processes. Our main contribution is to offer a unifying approach for the programming of distributed architectures...... on the web, which can capture web servers, stateful process execution, and the composition of services via mediation. We discuss applications of this approach through a series of examples that cover, e.g., static content serving, multiparty sessions, and the evolution of web systems. Finally, we present...... a performance evaluation that includes a comparison of Jolie-based web systems to other frameworks and a measurement of its scalability. © 2016 Elsevier B.V....

Identification of elastic properties of composite plate

International Nuclear Information System (INIS)

Kovalovs, A; Rucevskis, S

2011-01-01

Composite laminates are used extensively in the aerospace industry, especially for the fabrication of high-performance structures. The determination of stiffness parameters for complex materials, such as fibre-reinforced composites, is much more complicated than for isotropic materials. A conventional way is testing the coupon specimens, which are manufactured by technology similar to that used for the real, large structures. When such a method is used, the question arises of whether the material properties obtained from the coupon tests are the same as those in the large structure. Therefore, the determination of actual material properties for composite laminates using non-destructive evaluation techniques has been widely investigated. A number of various non-destructive evaluation techniques have been proposed for determining the material properties of composite laminates. In the present study, attention is focused on the identification of the elastic properties of laminated plate using vibration test data. The problem associated with vibration testing is converting the measured modal frequencies to elastic constants. A standard method for solving this problem is the use of a numerical-experimental model and optimization techniques. The identification functional represents the gap between the numerical model response and the experimental one. This gap should be minimized, taking into account the side constraints on the design variables (elastic constants). The minimization problem is solved by using non-linear mathematical programming techniques and sensitivity analysis. The results obtained were verified by comparing the experimentally measured eigenfrequencies with the numerical ones obtained by FEM at the point of optima

Composites Similarity Analysis Method Based on Knowledge Set in Composites Quality Control

OpenAIRE

Li Haifeng

2016-01-01

Composites similarity analysis is an important link of composites review, it can not only to declare composites review rechecking, still help composites applicants promptly have the research content relevant progress and avoid duplication. This paper mainly studies the composites similarity model in composites review. With the actual experience of composites management, based on the author’s knowledge set theory, paper analyzes deeply knowledge set representation of composites knowledge, impr...

Fossil Energy Materials Program conference proceedings

Energy Technology Data Exchange (ETDEWEB)

Judkins, R.R. (comp.)

1987-08-01

The US Department of Energy Office of Fossil Energy has recognized the need for materials research and development to assure the adequacy of materials of construction for advanced fossil energy systems. The principal responsibility for identifying needed materials research and for establishing a program to address these needs resides within the Office of Technical Coordination. That office has established the Advanced Research and Technology Development (AR and TD) Fossil Energy Materials Program to fulfill that responsibility. In addition to the AR and TD Materials Program, which is designed to address in a generic way the materials needs of fossil energy systems, specific materials support activities are also sponsored by the various line organizations such as the Office of Coal Gasification. A conference was held at Oak Ridge, Tennessee on May 19-21, 1987, to present and discuss the results of program activities during the past year. The conference program was organized in accordance with the research thrust areas we have established. These research thrust areas include structural ceramics (particularly fiber-reinforced ceramic composites), corrosion and erosion, and alloy development and mechanical properties. Eighty-six people attended the conference. Papers have been entered individually into EDB and ERA. (LTN)

Civil Defence and National Security: Composition and Implementation Model in National Defence

Directory of Open Access Journals (Sweden)

Mr. Muradi

2017-01-01

Full Text Available Civil Defense is inherent part of every citizen in many countries anywhere in the world, which differ only in the implementation of the program. The difference depends on the threat level and needs of each country in mobilizing citizens. However, the Civil Defense’s Governance which involvement of citizens is already regulated in a number of regulations and legislation, but as one part of an integrated program linked to the involvement of citizens in the framework of national defense, civil defense program is not enough to have its own laws. So that when applied in the form of operational, interpretation of these programs tend to be not in tune and even have precisely the opposite perspective between the state and citizens. This paper argued that the Civil Defense program is part of an integrated governance program of national security. Therefore, the state should be required to ensure that the program of Civil Defense goes well. This paper is also offer the composition and program models associated with the Civil Defense, Conscription Program (draftee and Reserve Component. The argument of this paper is that the Civil Defense Program is a linear and continuous with Conscription and Reserves Programs.

Gut microbiota composition may relate to weight loss rate in obese pet dogs

DEFF Research Database (Denmark)

Kieler, Ida Nordang; Bin Shamzir Kamal, Shamrulazhar; Vitger, Anne Désiré

2017-01-01

Obese dogs seem to have a different gut microbiome (GM) composition compared to lean dogs, and in humans, GM composition may negatively impact the ability to lose weight in some individuals. The purpose of this study was to investigate the interaction between exercise, weight......-loss and the composition of GM in dogs. Eighteen obese pet dogs were recruited for a 12-week weight-loss intervention. All dogs were fed restrictively with a commercial high-protein/high-fibre dry diet, and eight of these dogs were enrolled in an exercise program in addition to the diet intervention. Faecal samples were...... collected and the dogs were weighed at week 0, week 6 and week 12. GM composition was determined using MiSeq-based tag-encoded 16S rRNA gene high-throughput amplicon sequencing, and concentrations of short chain fatty acids (SCFA) by gas-liquid chromatography. Total weight loss, food allowance and GM were...

FY 2006 annual report. 21st century COE program isotope science and engineering from basics to applications

International Nuclear Information System (INIS)

2007-01-01

The 06' activity on 21st century COE program, Nagoya University, Isotopes open the future' is reported. The contents are: Research and educational execution planning; Operational reports (research activities, educational activities, international conferences, etc.); Research activities (1. the basic research field...isotope separation, isotope production, isotope measurement, and isotope materials, 2. the composite and development field...isotopes in biology, cultural science, and environment, 3. the young researchers unit for composite research, 4. research contributions); Educational activities (1. programs for assist of young researchers, 2. lectures on English, 3. lectures for postgraduate students). (J.P.N.)

Cell verification of parallel burnup calculation program MCBMPI based on MPI

International Nuclear Information System (INIS)

Yang Wankui; Liu Yaoguang; Ma Jimin; Wang Guanbo; Yang Xin; She Ding

2014-01-01

The parallel burnup calculation program MCBMPI was developed. The program was modularized. The parallel MCNP5 program MCNP5MPI was employed as neutron transport calculation module. And a composite of three solution methods was used to solve burnup equation, i.e. matrix exponential technique, TTA analytical solution, and Gauss Seidel iteration. MPI parallel zone decomposition strategy was concluded in the program. The program system only consists of MCNP5MPI and burnup subroutine. The latter achieves three main functions, i.e. zone decomposition, nuclide transferring and decaying, and data exchanging with MCNP5MPI. Also, the program was verified with the pressurized water reactor (PWR) cell burnup benchmark. The results show that it,s capable to apply the program to burnup calculation of multiple zones, and the computation efficiency could be significantly improved with the development of computer hardware. (authors)

FWP executive summaries, Basic Energy Sciences Materials Sciences Programs (SNL/NM)

Energy Technology Data Exchange (ETDEWEB)

Samara, G.A.

1997-05-01

The BES Materials Sciences Program has the central theme of Scientifically Tailored Materials. The major objective of this program is to combine Sandia`s expertise and capabilities in the areas of solid state sciences, advanced atomic-level diagnostics and materials synthesis and processing science to produce new classes of tailored materials as well as to enhance the properties of existing materials for US energy applications and for critical defense needs. Current core research in this program includes the physics and chemistry of ceramics synthesis and processing, the use of energetic particles for the synthesis and study of materials, tailored surfaces and interfaces for materials applications, chemical vapor deposition sciences, artificially-structured semiconductor materials science, advanced growth techniques for improved semiconductor structures, transport in unconventional solids, atomic-level science of interfacial adhesion, high-temperature superconductors, and the synthesis and processing of nano-size clusters for energy applications. In addition, the program includes the following three smaller efforts initiated in the past two years: (1) Wetting and Flow of Liquid Metals and Amorphous Ceramics at Solid Interfaces, (2) Field-Structured Anisotropic Composites, and (3) Composition-Modulated Semiconductor Structures for Photovoltaic and Optical Technologies. The latter is a joint effort with the National Renewable Energy Laboratory. Separate summaries are given of individual research areas.

A quantitative study of a physics-first pilot program

Energy Technology Data Exchange (ETDEWEB)

Pasero, Spencer Lee; /Northern Illinois U.

2008-09-01

Hundreds of high schools around the United States have inverted the traditional core sequence of high school science courses, putting physics first, followed by chemistry, and then biology. A quarter-century of theory, opinion, and anecdote are available, but the literature lacks empirical evidence of the effects of the program. The current study was designed to investigate the effects of the program on science achievement gain, growth in attitude toward science, and growth in understanding of the nature of scientific knowledge. One hundred eighty-five honor students participated in this quasi-experiment, self-selecting into either the traditional or inverted sequence. Students took the Explore test as freshmen, and the Plan test as sophomores. Gain scores were calculated for the composite scores and for the science and mathematics subscale scores. A two-factor analysis of variance (ANOVA) on course sequence and cohort showed significantly greater composite score gains by students taking the inverted sequence. Participants were administered surveys measuring attitude toward science and understanding of the nature of scientific knowledge twice per year. A multilevel growth model, compared across program groups, did not show any significant effect of the inverted sequence on either attitude or understanding of the nature of scientific knowledge. The sole significant parameter showed a decline in student attitude independent of course sequence toward science over the first two years of high school. The results of this study support the theory that moving physics to the front of the science sequence can improve achievement. The importance of the composite gain score on tests vertically aligned with the high-stakes ACT is discussed, and several ideas for extensions of the current study are offered.

Post-processor for simulations of the ORIGEN program and calculation of the composition of the activity of a burnt fuel core by a BWR type reactor

International Nuclear Information System (INIS)

Sandoval V, S.

2006-01-01

The composition calculation and the activity of nuclear materials subject to processes of burnt, irradiation and decay periods are of utility for diverse activities inside the nuclear industry, as they are it: the processes design and operations that manage radioactive material, the calculation of the inventory and activity of a core of burnt nuclear fuel, for studies of type Probabilistic Safety Analysis (APS), as well as for regulation processes and licensing of nuclear facilities. ORIGEN is a program for computer that calculates the composition and the activity of nuclear materials subject to periods of burnt, irradiation and decay. ORIGEN generates a great quantity of information whose processing and analysis are laborious, and it requires thoroughness to avoid errors. The automation of the extraction, conditioning and classification of that information is of great utility for the analyst. By means of the use of the post-processor presented in this work it is facilitated, it speeds up and wide the capacity of analysis of results, since diverse consultations with several classification options and filtrate of results can be made. As illustration of the utility of the post-processor, and as an analysis of interest for itself, it is also presented in this work the composition of the activity of a burned core in a BWR type reactor according to the following classification criteria: by type of radioisotope (fission products, activation products and actinides), by specie type (gassy, volatile, semi-volatile and not volatile), by element and by chemical group. The results show that the total activity of the studied core is dominated by the fission products and for the actinides, in proportion four to one, and that the gassy and volatile species conform a fifth part of the total activity of the core. (Author)

MS-SQL data base programming

Energy Technology Data Exchange (ETDEWEB)

Noh, Chang Bae; Kim, Nam Jung; Lee, Hyeong Gyo

2002-07-15

This is about MS-SQL data base programming which is divided into thirteen chapters. The contents of this book are to understand MS-SQL 2000 DBMS with its composition, new function and history of MS-SQL, to learn conception of data base, install, run and closing of MS-SQL 2000 DBMS, to deal with the basic of MS-SQL DBMS, to handle the intermediate level of MS-SQL DBMS, to deal with MS-SQL DBMS in advanced level, to practice query like changing data base and checking of data lists, function on its use and data diff, get date, date add, char, upper and system function, set-up of MS-SQL ODBC, constructing of web server of windows 2000, web programming using visual studio.net.making board and making reference room.

MS-SQL data base programming

International Nuclear Information System (INIS)

Noh, Chang Bae; Kim, Nam Jung; Lee, Hyeong Gyo

2002-07-01

This is about MS-SQL data base programming which is divided into thirteen chapters. The contents of this book are to understand MS-SQL 2000 DBMS with its composition, new function and history of MS-SQL, to learn conception of data base, install, run and closing of MS-SQL 2000 DBMS, to deal with the basic of MS-SQL DBMS, to handle the intermediate level of MS-SQL DBMS, to deal with MS-SQL DBMS in advanced level, to practice query like changing data base and checking of data lists, function on its use and data diff, get date, date add, char, upper and system function, set-up of MS-SQL ODBC, constructing of web server of windows 2000, web programming using visual studio.net.making board and making reference room.

Chemical vapor infiltration of TiB{sub 2} composites

Energy Technology Data Exchange (ETDEWEB)

Besmann, T.M. [Oak Ridge National Laboratory, TN (United States)

1995-05-01

This program is designed to develop a Hall-Heroult aluminum smelting cathode with substantially improved properties. The carbon cathodes in current use require significant anode-to-cathode spacing in order to prevent shorting, causing significant electrical inefficiencies. This is due to the non-wettability of carbon by aluminum which causes instability in the cathodic aluminum pad. It is suggested that a fiber reinforced-TiB{sub 2} matrix composite would have the requisite wettability, strength, strain-to-failure, cost, and lifetime to solve this problem. The approach selected to fabricate such a cathode material is chemical vapor infiltration (CVI). This program is designed to evaluate potential fiber reinforcements, fabricate test specimens, and test the materials in a static bath and lab-scale Hall cell.

Braided Composite Technologies for Rotorcraft Structures

Science.gov (United States)

Jessie, Nathan

2015-01-01

A&P Technology has developed a braided material approach for fabricating lightweight, high-strength hybrid gears for aerospace drive systems. The conventional metallic web was replaced with a composite element made from A&P's quasi-isotropic braid. The 0deg, +/-60deg braid architecture was chosen so that inplane stiffness properties and strength would be nearly equal in all directions. The test results from the Phase I Small Spur Gear program demonstrated satisfactory endurance and strength while providing a 20 percent weight savings. (Greater weight savings is anticipated with structural optimization.) The hybrid gears were subjected to a proof-of-concept test of 1 billion cycles in a gearbox at 10,000 revolutions per minute and 490 in-lb torque with no detectable damage to the gears. After this test the maximum torque capability was also tested, and the static strength capability of the gears was 7x the maximum operating condition. Additional proof-of-concept tests are in progress using a higher oil temperature, and a loss-of-oil test is planned. The success of Phase I led to a Phase II program to develop, fabricate, and optimize full-scale gears, specifically Bull Gears. The design of these Bull Gears will be refined using topology optimization, and the full-scale Bull Gears will be tested in a full-scale gear rig. The testing will quantify benefits of weight savings, as well as noise and vibration reduction. The expectation is that vibration and noise will be reduced through the introduction of composite material in the vibration transmission path between the contacting gear teeth and the shaft-and-bearing system.

A Quantitative Optimization Framework for Market-Driven Academic Program Portfolios

NARCIS (Netherlands)

Burgher, Joshua; Hamers, Herbert

2017-01-01

We introduce a quantitative model that can be used for decision support for planning and optimizing the composition of portfolios of market-driven academic programs within the context of higher education. This model is intended to enable leaders in colleges and universities to maximize financial

Sorption of radiocesium by composites of variable composition

International Nuclear Information System (INIS)

Someda, H.H.; El-zahhar, A.A.; Shehata, M.K.K.; El-Naggar, H.A.

2000-01-01

Cellulose and different natural materials - supported hexacyanoferrate composites were prepared and characterized by IR and x-ray diffraction studies. The stability of the prepared composites towards concentrated mineral acids was studied. The capacity of such prepared composites towards the uptake of cesium was calculated and found to be 1.5-1.7 meq/g. The capacity of the natural materials - supported composites was found to be slightly higher than that of the cellulose supported one. Different parameters affecting the sorption process of the radioelement such as acid concentration, Ph variation, competing ions and carrier concentration were studied. The release of the cesium traces from the composite materials was studied under different HCl concentrations and it was found that there is no release of the absorbed cesium up to 2.5 M even for long contact time up to two weeks. The work is under developing and extension

Utilization of ilmenite/epoxy composite for neutrons and gamma rays attenuation

Energy Technology Data Exchange (ETDEWEB)

El-Sayed Abdo, A. E-mail: attiaabdo11@hotmail.com; El-Sarraf, M.A.; Gaber, F.A

2003-01-01

This work deals with the study of ilmenite/epoxy composite as an injecting mortar for cracks developed in biological concrete shields, as well as, neutrons and gamma rays attenuation. Effects of the particle size on the mechanical strengths have been studied for epoxy resin filled with crushed ilmenite with different maximum particle sizes ranging from 32 to 500 {mu}m. Thermal neutrons and gamma rays attenuation in ilmenite/epoxy composites with 75 and 80 wt.% of ilmenite concentration have been investigated. The total mass attenuation coefficients {mu}/{rho} (cm{sup 2} g{sup -1}) of gamma ray for five ilmenite/epoxy composites have been calculated using the XCOM program (version 3.1) at energies from 10 keV to 100 MeV. Also, the total mass attenuation coefficients ({mu}/{rho}) have estimated based on the measured total linear attenuation coefficients ({mu}) and compared with the calculated results where, a reasonable agreement was found.

Ceramic Matrix Composite (CMC) Materials Characterization

Science.gov (United States)

Calomino, Anthony

2001-01-01

Under the former NASA EPM Program, much initial progress was made in identifying constituent materials and processes for SiC/SiC ceramic composite hot-section components. This presentation discusses the performance benefits of these approaches and elaborates on further constituent and property improvements made under NASA UEET. These include specific treatments at NASA that significantly improve the creep and environmental resistance of the Sylramic(TM) SiC fiber as well as the thermal conductivity and creep resistance of the CVI Sic matrix. Also discussed are recent findings concerning the beneficial effects of certain 2D-fabric architectures and carbon between the BN interphase coating and Sic matrix.

Ceramic Matrix Composite (CMC) Materials Development

Science.gov (United States)

DiCarlo, James

2001-01-01

Under the former NASA EPM Program, much initial progress was made in identifying constituent materials and processes for SiC/SiC ceramic composite hot-section components. This presentation discusses the performance benefits of these approaches and elaborates on further constituent and property improvements made under NASA UEET. These include specific treatments at NASA that significantly improve the creep and environmental resistance of the Sylramic(TM) Sic fiber as well as the thermal conductivity and creep resistance of the CVI Sic matrix. Also discussed are recent findings concerning the beneficial effects of certain 2D-fabric architectures and carbon between the BN interphase coating and Sic matrix.

The influence of day/night cycles on biomass yield and composition of Neochloris oleoabundans

NARCIS (Netherlands)

Winter, de Lenneke; Dominguez Teles, Iago; Martens, Dirk E.; Wijffels, René H.; Barbosa, Maria J.

2017-01-01

Background: Day/night cycles regulate the circadian clock of organisms to program daily activities. Many species of microalgae have a synchronized cell division when grown under a day/night cycle, and synchronization might influence biomass yield and composition. Therefore, the aim of this study

NASA's Upper Atmosphere Research Program (UARP) and Atmospheric Chemistry Modeling and Analysis Program (ACMAP): Research Summaries 1997-1999

Science.gov (United States)

Kurylo, M. J.; DeCola, P. L.; Kaye, J. A.

2000-01-01

Under the mandate contained in the FY 1976 NASA Authorization Act, the National Aeronautics and Space Administration (NASA) has developed and is implementing a comprehensive program of research, technology development, and monitoring of the Earth's upper atmosphere, with emphasis on the upper troposphere and stratosphere. This program aims at expanding our chemical and physical understanding to permit both the quantitative analysis of current perturbations as well as the assessment of possible future changes in this important region of our environment. It is carried out jointly by the Upper Atmosphere Research Program (UARP) and the Atmospheric Chemistry Modeling and Analysis Program (ACMAP), both managed within the Research Division in the Office of Earth Science at NASA. Significant contributions to this effort have also been provided by the Atmospheric Effects of Aviation Project (AEAP) of NASA's Office of Aero-Space Technology. The long-term objectives of the present program are to perform research to: understand the physics, chemistry, and transport processes of the upper troposphere and the stratosphere and their control on the distribution of atmospheric chemical species such as ozone; assess possible perturbations to the composition of the atmosphere caused by human activities and natural phenomena (with a specific emphasis on trace gas geographical distributions, sources, and sinks and the role of trace gases in defining the chemical composition of the upper atmosphere); understand the processes affecting the distributions of radiatively active species in the atmosphere, and the importance of chemical-radiative-dynamical feedbacks on the meteorology and climatology of the stratosphere and troposphere; and understand ozone production, loss, and recovery in an atmosphere with increasing abundances of greenhouse gases. The current report is composed of two parts. Part 1 summarizes the objectives, status, and accomplishments of the research tasks supported

Nondestructive evaluation of ceramic and metal matrix composites for NASA's HITEMP and enabling propulsion materials programs

Science.gov (United States)

Generazio, Edward R.

1992-01-01

In a preliminary study, ultrasonic, x-ray opaque, and fluorescent dye penetrants techniques were used to evaluate and characterize ceramic and metal matrix composites. Techniques are highlighted for identifying porosity, fiber alignment, fiber uniformity, matrix cracks, fiber fractures, unbonds or disbonds between laminae, and fiber-to-matrix bond variations. The nondestructive evaluations (NDE) were performed during processing and after thermomechanical testing. Specific examples are given for Si3N4/SiC (SCS-6 fiber), FeCrAlY/Al2O3 fibers, Ti-15-3/SiC (SCS-6 fiber) materials, and Si3N4/SiC (SCS-6 fiber) actively cooled panel components. Results of this study indicate that the choice of the NDE tools to be used can be optimized to yield a faithful and accurate evaluation of advanced composites.

Computer program for calculation of complex chemical equilibrium compositions and applications. Part 1: Analysis

Science.gov (United States)

Gordon, Sanford; Mcbride, Bonnie J.

1994-01-01

This report presents the latest in a number of versions of chemical equilibrium and applications programs developed at the NASA Lewis Research Center over more than 40 years. These programs have changed over the years to include additional features and improved calculation techniques and to take advantage of constantly improving computer capabilities. The minimization-of-free-energy approach to chemical equilibrium calculations has been used in all versions of the program since 1967. The two principal purposes of this report are presented in two parts. The first purpose, which is accomplished here in part 1, is to present in detail a number of topics of general interest in complex equilibrium calculations. These topics include mathematical analyses and techniques for obtaining chemical equilibrium; formulas for obtaining thermodynamic and transport mixture properties and thermodynamic derivatives; criteria for inclusion of condensed phases; calculations at a triple point; inclusion of ionized species; and various applications, such as constant-pressure or constant-volume combustion, rocket performance based on either a finite- or infinite-chamber-area model, shock wave calculations, and Chapman-Jouguet detonations. The second purpose of this report, to facilitate the use of the computer code, is accomplished in part 2, entitled 'Users Manual and Program Description'. Various aspects of the computer code are discussed, and a number of examples are given to illustrate its versatility.

Reusable Launch Vehicle Technology Program

Science.gov (United States)

Freeman, Delma C., Jr.; Talay, Theodore A.; Austin, R. Eugene

1997-01-01

Industry/NASA reusable launch vehicle (RLV) technology program efforts are underway to design, test, and develop technologies and concepts for viable commercial launch systems that also satisfy national needs at acceptable recurring costs. Significant progress has been made in understanding the technical challenges of fully reusable launch systems and the accompanying management and operational approaches for achieving a low cost program. This paper reviews the current status of the RLV technology program including the DC-XA, X-33 and X-34 flight systems and associated technology programs. It addresses the specific technologies being tested that address the technical and operability challenges of reusable launch systems including reusable cryogenic propellant tanks, composite structures, thermal protection systems, improved propulsion and subsystem operability enhancements. The recently concluded DC-XA test program demonstrated some of these technologies in ground and flight test. Contracts were awarded recently for both the X-33 and X-34 flight demonstrator systems. The Orbital Sciences Corporation X-34 flight test vehicle will demonstrate an air-launched reusable vehicle capable of flight to speeds of Mach 8. The Lockheed-Martin X-33 flight test vehicle will expand the test envelope for critical technologies to flight speeds of Mach 15. A propulsion program to test the X-33 linear aerospike rocket engine using a NASA SR-71 high speed aircraft as a test bed is also discussed. The paper also describes the management and operational approaches that address the challenge of new cost effective, reusable launch vehicle systems.

Analysis of composition and microstructural uniformity of hybrid glass/carbon fibre composites

Energy Technology Data Exchange (ETDEWEB)

Beauson, J.; Markussen, C.M.; Madsen, Bo

2013-09-01

In hybrid fibre composites, the intermixing of the two types of fibres imposes challenges to obtain materials with a well-defined and uniform microstructure. In the present paper, the composition and the microstructural uniformity of hybrid glass/carbon fibre composites mixed at the fibre bundle level are investigated. The different levels of compositions in the composites are defined and experimentally determined. The composite volume fractions are determined using an image analysis based procedure. The global fibre volume fractions are determined using a gravimetrical based method. The local fibre volume fractions are determined using volumetric calculations. A model is presented to predict the interrelation of volume fractions in hybrid fibre composites. The microstructural uniformity of the composites is analysed by the determined variation in composite volume fractions. Two analytical methods, a standard deviation based method and a fast Fourier transform method, are used to quantify the difference in microstructural uniformity between composites, and to detect and quantify any repeating pattern in the composite microstructure. (Author)

Spent reactor fuel benchmark composition data for code validation

International Nuclear Information System (INIS)

Bierman, S.R.

1991-09-01

To establish criticality safety margins utilizing burnup credit in the storage and transport of spent reactor fuels requires a knowledge of the uncertainty in the calculated fuel composition used in making the reactivity assessment. To provide data for validating such calculated burnup fuel compositions, radiochemical assays are being obtained as part of the United States Department of Energy From-Reactor Cask Development Program. Destructive assay data are being obtained from representative reactor fuels having experienced irradiation exposures up to about 55 GWD/MTM. Assay results and associated operating histories on the initial three samples analyzed in this effort are presented. The three samples were taken from different axial regions of the same fuel rod and represent radiation exposures of about 27, 37, and 44 GWD/MTM. The data are presented in a benchmark type format to facilitate identification/referencing and computer code input

Performance improvement of charge trap flash memory by using a composition-modulated high-k trapping layer

International Nuclear Information System (INIS)

Tang Zhen-Jie; Li Rong; Yin Jiang

2013-01-01

A composition-modulated (HfO 2 ) x (Al 2 O3) 1−x charge trapping layer is proposed for charge trap flash memory by controlling the Al atom content to form a peak and valley shaped band gap. It is found that the memory device using the composition-modulated (HfO 2 ) x (Al 2 O 3 ) 1−x as the charge trapping layer exhibits a larger memory window of 11.5 V, improves data retention even at high temperature, and enhances the program/erase speed. Improvements of the memory characteristics are attributed to the special band-gap structure resulting from the composition-modulated trapping layer. Therefore, the composition-modulated charge trapping layer may be useful in future nonvolatile flash memory device application. (condensed matter: electronic structure, electrical, magnetic, and optical properties)

Cooled Ceramic Matrix Composite Propulsion Structures Demonstrated

Science.gov (United States)

Jaskowiak, Martha H.; Dickens, Kevin W.

2005-01-01

NASA's Next Generation Launch Technology (NGLT) Program has successfully demonstrated cooled ceramic matrix composite (CMC) technology in a scramjet engine test. This demonstration represented the world s largest cooled nonmetallic matrix composite panel fabricated for a scramjet engine and the first cooled nonmetallic composite to be tested in a scramjet facility. Lightweight, high-temperature, actively cooled structures have been identified as a key technology for enabling reliable and low-cost space access. Tradeoff studies have shown this to be the case for a variety of launch platforms, including rockets and hypersonic cruise vehicles. Actively cooled carbon and CMC structures may meet high-performance goals at significantly lower weight, while improving safety by operating with a higher margin between the design temperature and material upper-use temperature. Studies have shown that using actively cooled CMCs can reduce the weight of the cooled flow-path component from 4.5 to 1.6 lb/sq ft and the weight of the propulsion system s cooled surface area by more than 50 percent. This weight savings enables advanced concepts, increased payload, and increased range. The ability of the cooled CMC flow-path components to operate over 1000 F hotter than the state-of-the-art metallic concept adds system design flexibility to space-access vehicle concepts. Other potential system-level benefits include smaller fuel pumps, lower part count, lower cost, and increased operating margin.

Damage Simulation in Composite Materials: Why It Matters and What Is Happening Currently at NASA in This Area

Science.gov (United States)

McElroy, Mack; de Carvalho, Nelson; Estes, Ashley; Lin, Shih-yung

2017-01-01

composites. The Advanced Composites Project (ACP) at NASA Langley has supported the development of composites damage simulation tools in a consortium of aerospace companies with a goal of reducing the certification time of a commercial aircraft by 30%. And while the scope of ACP does not include spacecraft, much of the methodology and simulation capabilities can apply to spacecraft certification in the Space Launch System and Orion programs as well. Some specific applications of composite damage simulation models in a certification program are (1) evaluation of damage during service when maintenance may be difficult or impossible, (2) a tool for early design iterations, (3) gaining insight into a particular damage process and applying this insight towards a test coupon or structural design, and (4) analysis of damage scenarios that are difficult or impossible to recreate in a test. As analysis capabilities improve, these applications and more will become realized resulting in a reduction in cost for use of composites in aerospace vehicles. NASA is engaged in this process from both research and application perspectives. In addition to the background information discussed previously, this presentation covers a look at recent research at NASA in this area and some current/potential applications in the Orion program.

Investigation of metal-matrix composite containing liquid-phase dispersion

Czech Academy of Sciences Publication Activity Database

Strunz, Pavel; Mukherji, D.; Gilles, R.; Geue, T.; Rösler, J.

2012-01-01

Roč. 340, 012098 (2012), s. 1-15 ISSN 1742-6588. [5th European Conference on Neutron Scattering. Praha, 17.07.2011-21.07.2011] R&D Projects: GA MPO FR-TI1/378 Grant - others:European Commission(XE) RII3-CT-2003-505925 Program:FP6 Institutional support: RVO:61389005 Keywords : metal-matrix composite * liquid-phase dispersion * strengthening * neutron diffraction Subject RIV: BM - Solid Matter Physics ; Magnetism http://iopscience.iop.org/1742-6596/340/1/012098

High-Temperature Polymer Composites Tested for Hypersonic Rocket Combustor Backup Structure

Science.gov (United States)

Sutter, James K.; Shin, E. Eugene; Thesken, John C.; Fink, Jeffrey E.

2005-01-01

Significant component weight reductions are required to achieve the aggressive thrust-toweight goals for the Rocket Based Combined Cycle (RBCC) third-generation, reusable liquid propellant rocket engine, which is one possible engine for a future single-stage-toorbit vehicle. A collaboration between the NASA Glenn Research Center and Boeing Rocketdyne was formed under the Higher Operating Temperature Propulsion Components (HOTPC) program and, currently, the Ultra-Efficient Engine Technology (UEET) Project to develop carbon-fiber-reinforced high-temperature polymer matrix composites (HTPMCs). This program focused primarily on the combustor backup structure to replace all metallic support components with a much lighter polymer-matrixcomposite- (PMC-) titanium honeycomb sandwich structure.

Microhardness of resin composite materials light-cured through fiber reinforced composite.

NARCIS (Netherlands)

Fennis, W.M.M.; Ray, N.J.; Creugers, N.H.J.; Kreulen, C.M.

2009-01-01

OBJECTIVES: To compare polymerization efficiency of resin composite basing materials when light-cured through resin composite and fiber reinforced composite (FRC) by testing microhardness. METHODS: Simulated indirect restorations were prepared by application of resin composite (Clearfil AP-X) or FRC

Surface roughness of etched composite resin in light of composite repair

NARCIS (Netherlands)

Loomans, B.A.C.; Cardoso, M.V.; Opdam, N.J.M.; Roeters, F.J.M.; Munck, J. De; Huysmans, M.C.D.N.J.M.; Meerbeek, B. Van

2011-01-01

OBJECTIVES: In search for clinically effective composite repair protocols, the effect of various etching protocols on the surface roughness of composite resins with different filler composition were investigated. METHODS: Of two composite resins (hybrid-filled Clearfil AP-X; nano-filled Filtek

Composition

DEFF Research Database (Denmark)

Bergstrøm-Nielsen, Carl

2014-01-01

Cue Rondo is an open composition to be realised by improvising musicians. See more about my composition practise in the entry "Composition - General Introduction". Caution: streaming the sound/video files will in some cases only provide a few minutes' sample, or the visuals will not appear at all....... Please DOWNLOAD them to see/hear them in full length! This work is licensed under a Creative Commons "by-nc" License. You may for non-commercial purposes use and distribute it, performance instructions as well as specially designated recordings, as long as the author is mentioned. Please see http...

CRACKER - a program coupling chemistry and transport. Version 92-11

Energy Technology Data Exchange (ETDEWEB)

Emren, A [Chalmers Univ. of Technology, Gothenburg (Sweden). Dept. of Nuclear Technology

1992-12-01

CRACKER is a program coupling chemistry and transport. It simulates chemical reactions of groundwater flowing through a plane fracture. Properties like initial composition of the water, mineralogical composition of the rock and temperature gradients and flow velocity of the water serve as input for the modelling. The program is designed to handle heterogeneous rock properties, like redox fronts, regions with different mineralogy etc. It is even able to handle the common situation of a rock violating the phase rule. In the CRACKER model, a rock is formed by a more or less random distribution of minerals across the surfaces of a fracture. Water moves along the fracture (in present version at a constant velocity). No diffusion parallel to the flow direction is simulated. CRACKER is a package of several programs, most of them written in C. Chemical equilibrium calculations are mostly performed by the well-known geochemical program PHREEQE. The main program, CRACKER, manages information flow and determines which subprograms to use for specific tasks. Further it is responsible for the user interface. Essentially a simulation proceeds by alternate call to the HACKER and PHREEQE subprograms. HACKER is responsible for generating the rock, water propagation, mixing of waters and sampling the results. PHREEQE is used to solve the chemical equilibrium equations. The directory structure and the data structures used by CRACKER are described in separate sections. Further, the different subprograms are described with respect to purposes and methods used to handle the problems. The purpose of each first level function in the subprograms is described. (author).

CRACKER - a program coupling chemistry and transport. Version 92-11

International Nuclear Information System (INIS)

Emren, A.

1992-12-01

CRACKER is a program coupling chemistry and transport. It simulates chemical reactions of groundwater flowing through a plane fracture. Properties like initial composition of the water, mineralogical composition of the rock and temperature gradients and flow velocity of the water serve as input for the modelling. The program is designed to handle heterogeneous rock properties, like redox fronts, regions with different mineralogy etc. It is even able to handle the common situation of a rock violating the phase rule. In the CRACKER model, a rock is formed by a more or less random distribution of minerals across the surfaces of a fracture. Water moves along the fracture (in present version at a constant velocity). No diffusion parallel to the flow direction is simulated. CRACKER is a package of several programs, most of them written in C. Chemical equilibrium calculations are mostly performed by the well-known geochemical program PHREEQE. The main program, CRACKER, manages information flow and determines which subprograms to use for specific tasks. Further it is responsible for the user interface. Essentially a simulation proceeds by alternate call to the HACKER and PHREEQE subprograms. HACKER is responsible for generating the rock, water propagation, mixing of waters and sampling the results. PHREEQE is used to solve the chemical equilibrium equations. The directory structure and the data structures used by CRACKER are described in separate sections. Further, the different subprograms are described with respect to purposes and methods used to handle the problems. The purpose of each first level function in the subprograms is described. (author)

GRUCAL: a program system for the calculation of macroscopic group constants

International Nuclear Information System (INIS)

Woll, D.

1984-01-01

Nuclear reactor calculations require material- and composition-dependent, energy-averaged neutron physical data in order to decribe the interaction between neutrons and isotopes. The multigroup cross section code GRUCAL calculates these macroscopic group constants for given material compositions from the material-dependent data of the group constant library GRUBA. The instructions for calculating group constants are not fixed in the program, but are read in from an instruction file. This makes it possible to adapt GRUCAL to various problems or different group constant concepts

Linear programming mathematics, theory and algorithms

CERN Document Server

1996-01-01

Linear Programming provides an in-depth look at simplex based as well as the more recent interior point techniques for solving linear programming problems. Starting with a review of the mathematical underpinnings of these approaches, the text provides details of the primal and dual simplex methods with the primal-dual, composite, and steepest edge simplex algorithms. This then is followed by a discussion of interior point techniques, including projective and affine potential reduction, primal and dual affine scaling, and path following algorithms. Also covered is the theory and solution of the linear complementarity problem using both the complementary pivot algorithm and interior point routines. A feature of the book is its early and extensive development and use of duality theory. Audience: The book is written for students in the areas of mathematics, economics, engineering and management science, and professionals who need a sound foundation in the important and dynamic discipline of linear programming.

Robust high temperature composite and CO sensor made from such composite

Science.gov (United States)

Dutta, Prabir K.; Ramasamy, Ramamoorthy; Li, Xiaogan; Akbar, Sheikh A.

2010-04-13

Described herein is a composite exhibiting a change in electrical resistance proportional to the concentration of a reducing gas present in a gas mixture, detector and sensor devices comprising the composite, a method for making the composite and for making devices comprising the composite, and a process for detecting and measuring a reducing gas in an atmosphere. In particular, the reducing gas may be carbon monoxide and the composite may comprise rutile-phase TiO2 particles and platinum nanoclusters. The composite, upon exposure to a gas mixture containing CO in concentrations of up to 10,000 ppm, exhibits an electrical resistance proportional to the concentration of the CO present. The composite is useful for making sensitive, low drift, fast recovering detectors and sensors, and for measuring CO concentrations in a gas mixture present at levels from sub-ppm up to 10,000 ppm. The composites, and devices made from the composites, are stable and operable in a temperature range of from about 450.degree. C. to about 700.degree. C., such as may be found in a combustion chamber.

A Method of Sample Models of Program Construction in Terms of Petri Nets

Directory of Open Access Journals (Sweden)

D. I. Kharitonov

2015-01-01

Full Text Available In the article a method of automated construction of Petri nets simulating the behaviour of imperative programs is considered from the formal point of view. Petri net samples with certain characteristics are necessary in programming new algorithms for program analysis; in particular, they can be used for developing or optimizing algorithms of Petri nets compositions and decompositions, building the reachability tree, checking invariants and so on. The generation process consists of two stages. At the first stage, construction templates for a resulting net and parameters for construction are described. With the help of these parameters it is possible to regulate the final size and the absolute or relative amount of certain structures in the resulting net. At the second stage, iterative process of automated net construction is used for Petri net generation of any size, limited only by an available computer memory. In the first section of the article the minimum necessary definitions are given and a new version of Petri nets composition operation by places is introduced. Commutative and associative properties of introduced binary operation allow to synchronize any number of Petri nets in arbitrary order. Then construction template is defined as a marked Petri net with input and output interfaces and rules for templates composition using this interfaces. A number of construction templates can be united in a collection, for which the evolution rules are defined. The completeness property of a collection guarantees that the collection evolution results in a Petri net that simulates the imperative program behavior. The article provides a version of the construction templates complete collection and an example of Petri net simulating sequential imperative program construction.

Contributions for the supervision of social programs with a focus on the family

Directory of Open Access Journals (Sweden)

Carlos Eduardo Aguilera Campos

2007-04-01

Full Text Available This article explores the following factors of intervention: the professional composition of the social programs aimed at families, the new focus on the family in social policies and supervision by multi-disciplinary teams. It is based on an analysis of recent federal programs: the Integral Family Attention Program and the Family Health Program. It reviews the supervision without presenting a strictly theoretical approach or a list of field procedures. The family is considered as a social institution undergoing a permanent change of formats and meanings that require reflection and the continuous education of social professionals.

The Use of Current Media in Literature and Composition at the Community College Level.

Science.gov (United States)

Laughlin, Jody

Current media--films, videos, television programs, advertising in both print and television, and newspaper and magazine articles--can be successfully employed in college literature and composition classes, enhancing the learning environment by involving those students who might otherwise show disinterest. For example, a unit on pornography,…

Implementing and evaluating a program to facilitate chronic disease prevention and screening in primary care: a mixed methods program evaluation.

Science.gov (United States)

Manca, Donna Patricia; Aubrey-Bassler, Kris; Kandola, Kami; Aguilar, Carolina; Campbell-Scherer, Denise; Sopcak, Nicolette; O'Brien, Mary Ann; Meaney, Christopher; Faria, Vee; Baxter, Julia; Moineddin, Rahim; Salvalaggio, Ginetta; Green, Lee; Cave, Andrew; Grunfeld, Eva

2014-10-08

The objectives of this paper are to describe the planned implementation and evaluation of the Building on Existing Tools to Improve Chronic Disease Prevention and Screening in Primary Care (BETTER 2) program which originated from the BETTER trial. The pragmatic trial, informed by the Chronic Care Model, demonstrated the effectiveness of an approach to Chronic Disease Prevention and Screening (CDPS) involving the use of a new role, the prevention practitioner. The desired goals of the program are improved clinical outcomes, reduction in the burden of chronic disease, and improved sustainability of the health-care system through improved CDPS in primary care. The BETTER 2 program aims to expand the implementation of the intervention used in the original BETTER trial into communities across Canada (Alberta, Ontario, Newfoundland and Labrador, the Northwest Territories and Nova Scotia). This proactive approach provides at-risk patients with an intervention from the prevention practitioner, a health-care professional. Using the BETTER toolkit, the prevention practitioner determines which CDPS actions the patient is eligible to receive, and through shared decision-making and motivational interviewing, develops a unique and individualized 'prevention prescription' with the patient. This intervention is 1) personalized; 2) addressing multiple conditions; 3) integrated through linkages to local, regional, or national resources; and 4) longitudinal by assessing patients over time. The BETTER 2 program brings together primary care providers, policy/decision makers and researchers to work towards improving CDPS in primary care. The target patient population is adults aged 40-65. The reach, effectiveness, adoption, implementation, maintain (RE-AIM) framework will inform the evaluation of the program through qualitative and quantitative methods. A composite index will be used to quantitatively assess the effectiveness of the prevention practitioner intervention. The CDPS actions

The study of fix composite panel and steel plates on testing stand

Science.gov (United States)

Wróbel, A.; Płaczek, M.; Wachna, M.

2016-08-01

In this paper the practical possibilities of strength verification analysis of composite materials used in the manufacture of selected components of railway wagons are presented. Real laboratory stand for measurements in a scale controlled by PLC controller were made. The study of different types of connections of composite materials with sheet metal is presented. In one of the chapter of this paper principles construction of testing stand with pneumatic cylinder were presented. Mainly checking of displacements and stresses generated on the sheet as a result of pneumatic actuators load for composite boards was carried out. The use of the controller with operating panel allows to easy programming testing cycle. The user can define the force generated by the actuator by change of air pressure in cylinder. Additionally the location of acting cylinders and their jump can be changed by operator. The examination of the volume displacements was done by displacement sensor, and the tensile strain gauge. All parameters are written in CatmanEasy - data acquisition software. This article presents the study of stresses and displacements in the composite plates joined with sheet metal, in summary of this article, the authors compare the obtained results with the computer simulation results in the article: "Simulation of stresses in an innovative combination of composite with sheet".

Processing, properties and applications of composites using powder-coated epoxy towpreg technology

Science.gov (United States)

Bayha, T. D.; Osborne, P. P.; Thrasher, T. P.; Hartness, J. T.; Johnston, N. J.; Marchello, J. M.; Hugh, M. K.

1993-01-01

Composite manufacturing using the current prepregging technology of impregnating liquid resin into three-dimensionally reinforced textile preforms can be a costly and difficult operation. Alternatively, using polymer in the solid form, grinding it into a powder, and then depositing it onto a carbon fiber tow prior to making a textile preform is a viable method for the production of complex textile shapes. The powder-coated towpreg yarn is stable, needs no refrigeration, contains no solvents and is easy to process into various woven and braided preforms for later consolidation into composite structures. NASA's Advanced Composites Technology (ACT) program has provided an avenue for developing the technology by which advanced resins and their powder-coated preforms may be used in aircraft structures. Two-dimensional braiding and weaving studies using powder-coated towpreg have been conducted to determine the effect of resin content, towpreg size and twist on textile composite properties. Studies have been made to customize the towpreg to reduce friction and bulk factor. Processing parameters have been determined for three epoxy resin systems on eight-harness satin fabric, and on more advanced 3-D preform architectures for the downselected resin system. Processing effects and the resultant mechanical properties of these textile composites will be presented and compared.

NASA-UVA Light Aerospace Alloy and Structures Technology Program (LA2ST). Research on Materials for the High Speed Civil Transport

Science.gov (United States)

Gangloff, Richard P.; Starke, Edgar A., Jr.; Kelly, Robert G.; Scully, John R.; Stoner, Glenn E.; Wert, John A.

1997-01-01

Since 1986, the NASA-Langley Research Center has sponsored the NASA-UVa Light Alloy and Structures Technology (LA2ST) Program at the University of Virginia (UVa). The fundamental objective of the LA2ST program is to conduct interdisciplinary graduate student research on the performance of next generation, light-weight aerospace alloys, composites and thermal gradient structures. The LA2ST program has aimed to product relevant data and basic understanding of material mechanical response, environmental/corrosion behavior, and microstructure; new monolithic and composite alloys; advanced processing methods; measurement and modeling advances; and a pool of educated graduate students for aerospace technologies. The scope of the LA2ST Program is broad. Research areas include: (1) Mechanical and Environmental Degradation Mechanisms in Advanced Light Metals and Composites, (2) Aerospace Materials Science, (3) Mechanics of materials for Aerospace Structures, and (4) Thermal Gradient Structures. A substantial series of semi-annual progress reports issued since 1987 documents the technical objectives, experimental or analytical procedures, and detailed results of graduate student research in these topical areas.

Control and design of volumetric composition in pultruded hybrid fibre composites

DEFF Research Database (Denmark)

Madsen, Bo; Hashemi, Fariborz; Tahir, Paridah

2016-01-01

composition (i.e. volume fractions of fibres, matrix and porosity) in hybrid fibre composites. The model is based on a constant local fibre volume fraction criterion. Good agreement is found between model predictions and experimental data of pultruded hybrid kenaf/glass fibre composites with variable hybrid...... fibre weight mixing ratios. To demonstrate the suitability of the model, simulations are performed for four different cases of volumetric composition in hybrid kenaf/glass composites....

Pyridine-type alkaloid composition affects bacterial community composition of floral nectar.

Science.gov (United States)

Aizenberg-Gershtein, Yana; Izhaki, Ido; Santhanam, Rakesh; Kumar, Pavan; Baldwin, Ian T; Halpern, Malka

2015-06-30

Pyridine-type alkaloids are most common in Nicotiana species. To study the effect of alkaloid composition on bacterial community composition in floral nectar, we compared the nicotine-rich wild type (WT) N. attenuata, the nicotine biosynthesis-silenced N. attenuata that was rich in anatabine and the anabasine-rich WT N. glauca plants. We found that the composition of these secondary metabolites in the floral nectar drastically affected the bacterial community richness, diversity and composition. Significant differences were found between the bacterial community compositions in the nectar of the three plants with a much greater species richness and diversity in the nectar from the transgenic plant. The highest community composition similarity index was detected between the two wild type plants. The different microbiome composition and diversity, caused by the different pyridine-type alkaloid composition, could modify the nutritional content of the nectar and consequently, may contribute to the change in the nectar consumption and visitation. These may indirectly have an effect on plant fitness.

Bisphenol A Release: Survey of the Composition of Dental Composite Resins.

Science.gov (United States)

Dursun, Elisabeth; Fron-Chabouis, Hélène; Attal, Jean-Pierre; Raskin, Anne

2016-01-01

Bisphenol A (BPA) is an endocrine disruptor with potential toxicity. Composite resins may not contain pure BPA, but its derivatives are widely used. Several studies found doses of BPA or its derivatives in saliva or urine of patients after composite resin placement. The aims of this study were to establish an exhaustive list of composite resins marketed in Europe and their composition, and to assess the extent of BPA derivatives used. A research on manufacturers' websites was performed to reference all composite resins marketed in Europe, then their composition was determined from both material safety data sheets and a standardized questionnaire sent to manufacturers. Manufacturers had to indicate whether their product contained the monomers listed, add other monomers if necessary, or indicate "not disclosed". 160 composite resins were identified from 31 manufacturers and 23 manufacturers (74.2%) responded to the survey. From the survey and websites, the composition of 130 composite resins (81.2%) was: 112 (86.2%) based on BPA derivatives, 97 (74.7%) on bis-GMA, 17 (13.1%) without monomer derived from BPA (UDMA, sometimes with TEGDMA) and 6 (4.6%) with UDMA (only); 1 (0.8%) did not contain a BPA derivative or UDMA or TEGDMA. Pure BPA was never reported. This work has established a list of 18 composite resins that contain no BPA derivative. Manufacturers should be required to report the exact composition of their products as it often remains unclear or incomplete.

The WIPP Water Quality Sampling Program

International Nuclear Information System (INIS)

Uhland, D.; Morse, J.G.; Colton, D.

1986-01-01

The Waste Isolation Pilot Plant (WIPP), a Department of Energy facility, will be used for the underground disposal of wastes. The Water Quality Sampling Program (WQSP) is designed to obtain representative and reproducible water samples to depict accurate water composition data for characterization and monitoring programs in the vicinity of the WIPP. The WQSP is designed to input data into four major programs for the WIPP project: Geochemical Site Characterization, Radiological Baseline, Environmental Baseline, and Performance Assessment. The water-bearing units of interest are the Culebra and Magneta Dolomite Members of the Rustler Formation, units in the Dewey Lake Redbeds, and the Bell Canyon Formation. At least two chemically distinct types of water occur in the Culebra, one being a sodium/potassium chloride water and the other being a calcium/magnesium sulfate water. Water from the Culebra wells to the south of the WIPP site is distinctly fresher and tends to be of the calcium/magnesium sulfate type. Water in the Culebra in the north and around the WIPP site is distinctly fresher and tends to be of the sodium/potassium chloride type and is much higher in total dissolved solids. The program, which is currently 1 year old, will continue throughout the life of the facility as part of the Environmental Monitoring Program

The NASA cosmic ray program for the 1990's and beyond Interim report of the NASA Cosmic Ray Program Working Group

International Nuclear Information System (INIS)

Ahlen, S.P.; Binns, W.R.; Cherry, M.L.; Gaisser, T.K.; Jones, W.V.; Ling, J.C.; Mewaldt, R.A.; Muller, D.; Ormes, J.O.; Ramaty, R.; Stone, E.C.; Waddington, C.J.; Webber, W.R.; Miedenbeck, M.E.

1990-01-01

The interim report of the 1989 NASA Cosmic Ray Program Working Group is presented. The report summarizes the cosmic ray program for the 1990's, including the recently approved ACE, Astromag, HNC, POEMS, and SAMPEX missions, as well as other key elements of the program. New science themes and candidate missions are identified for the first part of the 21st Century, including objectives that might be addressed as part of the Human Exploration Initiative. Among the suggested new thrusts for the 21st century are: an Interstellar Probe into the nearby interstellar medium; a Lunar-Based Calorimeter to measure the cosmic ray composition near ∼10 16 eV; high precision element and isotope spectroscopy of ultraheavy (Z≥30) elements; and new, more sensitive, studies of impulsive solar flare events

Computer program for calculation of complex chemical equilibrium compositions and applications. Supplement 1: Transport properties

Science.gov (United States)

Gordon, S.; Mcbride, B.; Zeleznik, F. J.

1984-01-01

An addition to the computer program of NASA SP-273 is given that permits transport property calculations for the gaseous phase. Approximate mixture formulas are used to obtain viscosity and frozen thermal conductivity. Reaction thermal conductivity is obtained by the same method as in NASA TN D-7056. Transport properties for 154 gaseous species were selected for use with the program.

Optimization Formulations for the Maximum Nonlinear Buckling Load of Composite Structures

DEFF Research Database (Denmark)

Lindgaard, Esben; Lund, Erik

2011-01-01

This paper focuses on criterion functions for gradient based optimization of the buckling load of laminated composite structures considering different types of buckling behaviour. A local criterion is developed, and is, together with a range of local and global criterion functions from literature......, benchmarked on a number of numerical examples of laminated composite structures for the maximization of the buckling load considering fiber angle design variables. The optimization formulations are based on either linear or geometrically nonlinear analysis and formulated as mathematical programming problems...... solved using gradient based techniques. The developed local criterion is formulated such it captures nonlinear effects upon loading and proves useful for both analysis purposes and as a criterion for use in nonlinear buckling optimization. © 2010 Springer-Verlag....

Mesostructured Cu–Mn–Ce–O composites with homogeneous bulk composition for chlorobenzene removal: Catalytic performance and microactivation course

Energy Technology Data Exchange (ETDEWEB)

He, Chi, E-mail: chi_he@mail.xjtu.edu.cn [Department of Environmental Science and Engineering, School of Energy and Power Engineering, Xi' an Jiaotong University, Xi' an 710049 (China); Yu, Yanke [Key Lab of Urban Environment and Health, Institute of Urban Environment, Chinese Academy of Sciences, Xiamen 361021 (China); Shi, Jianwen [Center of Nanomaterials for Renewable Energy, State Key Laboratory of Electrical Insulation and Power Equipment, School of Electrical Engineering, Xi' an Jiaotong University, Xi' an 710049 (China); Shen, Qun [Research Center for Greenhouse Gases and Environmental Engineering, Shanghai Advanced Research Institute, Chinese Academy of Sciences, Shanghai 201210 (China); Chen, Jinsheng [Key Lab of Urban Environment and Health, Institute of Urban Environment, Chinese Academy of Sciences, Xiamen 361021 (China); Liu, Hongxia, E-mail: hxliu72@mail.xjtu.edu.cn [Department of Environmental Science and Engineering, School of Energy and Power Engineering, Xi' an Jiaotong University, Xi' an 710049 (China)

2015-05-01

Cu–Mn–Ce–O composites with enhanced surface area and developed mesoporosity were synthesized using a homogeneous coprecipitation (hcp) method, and were tested in the catalytic destruction of chlorobenzene (CB). X-ray diffraction (XRD), N{sub 2} adsorption/desorption, field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), temperature programmed reduction (H{sub 2}-TPR), temperature programmed desorption of CB/O{sub 2} (CB/O{sub 2}-TPD), and diffuse reflectance ultraviolet visible spectroscopy (DRUV-Vis) were used to characterize the structure and textural properties of catalysts. Mn and Cu enter CeO{sub 2} matrix with a fluorite-like structure, and produce large amounts of oxygen vacancies. Addition of manganese promotes the formation of reduced copper phase, and the presence of large numbers of high valence Mn{sup 4+} ions strongly enhances the redox couple of Cu{sup +}–Cu{sup 2+} in the composites. Both the synthesis protocol and metal doping amount significantly affect the catalyst reducibility, surface state and oxygen density. Cu{sub 0.15}Mn{sub 0.15}Ce{sub 0.85}O{sub x} synthesized via the hcp method exhibits the highest catalytic activity with 90% of chlorobenzene destructed at 255 °C (CO{sub 2} selectivity > 99.5%). Enriched surface oxygen, excellent active oxygen mobility and CB adsorption ability guarantee the superior activity and stability of Cu–Mn–Ce–O composite catalysts. Nucleophilic and electrophilic substitutions happen in sequence during chlorobenzene destruction, and the adsorbed Cl can be finally removed in the form of Cl{sub 2} via the Deacon reaction. Furthermore, the incorporation of CuO and MnO{sub x} phases can inhibit the formation of organic byproducts, such as phenolates, maleates, and o-benzoquinone-type species, especially at elevated reaction temperatures. - Highlights: • Cu–Mn–Ce–O mesoporous oxides possess enhanced surface oxygen

Inplane shear capacity of reinforced composite masonry block walls

International Nuclear Information System (INIS)

White, W.H.; Tseng, W.S.

1981-01-01

The objective of this paper is to describe a test program performed to determine the inplane shear capacity, stiffness and ductility of composite masonry walls subjected to earthquake type loadings. Specimens were simultaneously subjected to a range of compressive loads to simulate dead load; and inplane shear loads with full load reversal to simulate the earthquake cycling load. The influence of horizontal and vertical reinforcing steel percentages on the inplane shear capacity, stiffness and ductility was also investigated. (orig./HP)

Ecological Characterization Data for the 2004 Composite Analysis

Energy Technology Data Exchange (ETDEWEB)

Downs, Janelle L.; Simmons, Mary A.; Stegen, Jennifer A.; Bunn, Amoret L.; Tiller, Brett L.; Thorsten, Susan L.; Zufelt, Rhett K.

2004-11-01

A composite analysis is required by U.S. Department of Energy (DOE) Order 435.1 to ensure public safety through the management of active and planned low-level radioactive waste disposal facilities associated with the Hanford Site. The original Hanford Site Composite Analysis of 1998 must be revised and submitted to DOE Headquarters (DOE-HQ) in 2004 because of revisions to waste site information in the 100, 200, and 300 Areas, updated performance assessments and environmental impact statements (EIS), changes in inventory estimates for key sites and constituents, and a change in the definition of offsite receptors. Beginning in fiscal year (FY) 2003, the DOE Richland Operations Office (DOE-RL) initiated activities, including the development of data packages, to support the 2004 Composite Analysis. This report describes the data compiled in FY 2003 to support ecological site assessment modeling for the 2004 Composite Analysis. This work was conducted as part of the Characterization of Systems Task of the Groundwater Remediation Project (formerly the Groundwater Protection Program) managed by Fluor Hanford, Inc., Richland, Washington. The purpose of this report is to provide summaries of the characterization information and available spatial data on the biological resources and ecological receptors found in the upland, riparian, aquatic, and island habitats on the Hanford Site. These data constitute the reference information used to establish parameters for the ecological risk assessment module of the System Assessment Capability and other assessment activities requiring information on the presence and distribution of biota on the Hanford Site.

Ecological Characterization Data for the 2004 Composite Analysis

International Nuclear Information System (INIS)

Downs, Janelle L.; Simmons, Mary A.; Stegen, Amanda A.; Bunn, Amoret L.; Tiller, Brett L.; Thorsten, Susan L.; Zufelt, Rhett K.

2004-01-01

A composite analysis is required by U.S. Department of Energy (DOE) Order 435.1 to ensure public safety through the management of active and planned low-level radioactive waste disposal facilities associated with the Hanford Site. The original Hanford Site Composite Analysis of 1998 must be revised and submitted to DOE Headquarters (DOE-HQ) in 2004 because of revisions to waste site information in the 100, 200, and 300 Areas, updated performance assessments and environmental impact statements (EIS), changes in inventory estimates for key sites and constituents, and a change in the definition of offsite receptors. Beginning in fiscal year (FY) 2003, the DOE Richland Operations Office (DOE-RL) initiated activities, including the development of data packages, to support the 2004 Composite Analysis. This report describes the data compiled in FY 2003 to support ecological site assessment modeling for the 2004 Composite Analysis. This work was conducted as part of the Characterization of Systems Task of the Groundwater Remediation Project (formerly the Groundwater Protection Program) managed by Fluor Hanford, Inc., Richland, Washington. The purpose of this report is to provide/SUMmaries of the characterization information and available spatial data on the biological resources and ecological receptors found in the upland, riparian, aquatic, and island habitats on the Hanford Site. These data constitute the reference information used to establish parameters for the ecological risk assessment module of the System Assessment Capability and other assessment activities requiring information on the presence and distribution of biota on the Hanford Site

Propulsion system materials program. Semiannual progress report, October 1995--March 1996

Energy Technology Data Exchange (ETDEWEB)

Johnson, D.R.

1996-07-01

This portion of the program is identified as program element 1.0 within the work breakdown structure (WBS). It contains five subelements: (1) Monolithics, (2) Ceramic Composites, (3) Thermal and Wear Coatings, (4) Joining, and (5) Ceramic Machining. Ceramic research conducted within the Monolithics subelement currently includes work activities on low Cost Si{sub 3}N{sub 4} powder, green state ceramic fabrication, characterization, and densification, and on structural, mechanical, and physical properties of these ceramics. Research conducted within the Ceramic Composites subelement currently includes silicon nitride and oxide-based composites, and low expansion materials. Research conducted in the Thermal and Wear Coatings subelement is currently limited to oxide-based coatings and involves coating synthesis, characterization, and determination of the mechanical and physical properties of the coatings. Research conducted in the Joining subelement currently includes studies of processes to produce strong, stable joints between zirconia ceramics and iron-base alloys. As part of an expanded effort to reduce the cost of ceramic components, a new initiative in cost effective machining has been started. A major objective of the research in the Materials and Processing program element is to systematically advance the understanding of the relationships between ceramic raw materials such as powders and reactant gases, the processing variables involved in producing the ceramic materials, and the resultant microstructures and physical and mechanical properties of the ceramic materials. Success in meeting this objective will provide U.S. companies with new or improved ways for producing economical, highly reliable ceramic components for advanced heat engines.

KNN–NTK composite lead-free piezoelectric ceramic

Energy Technology Data Exchange (ETDEWEB)

Matsuoka, T., E-mail: ta-matsuoka@mg.ngkntk.co.jp; Kozuka, H.; Kitamura, K.; Yamada, H.; Kurahashi, T.; Yamazaki, M.; Ohbayashi, K. [NGK SPARK PLUG Co., Ltd., 2808 Iwasaki, Komaki, Aichi 485-8510 (Japan)

2014-10-21

A (K,Na)NbO₃-based lead-free piezoelectric ceramic was successfully densified. It exhibited an enhanced electromechanical coupling factor of kₚ=0.52, a piezoelectric constant d₃₃=252 pC/N, and a frequency constant Nₚ=3170 Hz m because of the incorporation of an elaborate secondary phase composed primarily of KTiNbO₅. The ceramic's nominal composition was 0.92K₀.₄₂Na₀.₄₄Ca₀.₀₄Li₀.₀₂Nb₀.₈₅O₃–0.047K₀.₈₅Ti₀.₈₅Nb₁.₁₅O₅–0.023BaZrO₃ –0.0017Co₃O₄–0.002Fe₂O₃–0.005ZnO, abbreviated herein as KNN–NTK composite. The KNN–NTK ceramic exhibited a dense microstructure with few microvoids which significantly degraded its piezoelectric properties. Elemental maps recorded using transmission electron microscopy with energy-dispersive X-ray spectroscopy (TEM–EDS) revealed regions of high concentrations of Co and Zn inside the NTK phase. In addition, X-ray diffraction patterns confirmed that a small portion of the NTK phase was converted into K₂(Ti,Nb,Co,Zn)₆O₁₃ or CoZnTiO₄ by a possible reaction between Co and Zn solutes and the NTK phase during a programmed sintering schedule. TEM studies also clarified a distortion around the KNN/NTK interfaces. Such an NTK phase filled voids between KNN particles, resulting in an improved chemical stability of the KNN ceramic. The manufacturing process was subsequently scaled to 100 kg per batch for granulated ceramic powder using a spray-drying technique. The properties of the KNN–NTK composite ceramic produced using the scaled-up method were confirmed to be identical to those of the ceramic prepared by conventional solid-state reaction sintering. Consequently, slight changes in the NTK phase composition and the distortion around the KNN/NTK interfaces affected the KNN–NTK composite ceramic's piezoelectric characteristics.

Test results of Nb3Sn ribbons for the Princeton D coil test program

International Nuclear Information System (INIS)

Kaugerts, J.; File, J.; Willard, J.W.

1974-10-01

A previously described D coil test program was modified. Details of a smaller Nb 3 Sn D coil test program are described. Cusp coil tests were made with several Nb 3 Sn composite ribbons. Measurements of both the quench and recovery currents as a function of magnetic field component perpendicular to the wide edge of the ribbon are presented. (auth)

Salt Composition Derived from Veazey Composition by Thermodynamic Modeling and Predicted Composition of Drum Contents

Energy Technology Data Exchange (ETDEWEB)

Weisbrod, Kirk Ryan [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Veirs, Douglas Kirk [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Funk, David John [Los Alamos National Lab. (LANL), Los Alamos, NM (United States); Clark, David Lewis [Los Alamos National Lab. (LANL), Los Alamos, NM (United States)

2016-03-11

This report describes the derivation of the salt composition from the Veazey salt stream analysis. It also provides an estimate of the proportions of the kitty litter, nitrate salt and neutralizer that was contained in drum 68660. While the actinide content of waste streams was judiciously followed in the 1980s in TA-55, no record of the salt composition could be found. Consequently, a salt waste stream produced from 1992 to 1994 and reported by Gerry Veazey provided the basis for this study. While chemical analysis of the waste stream was highly variable, an average analysis provided input to the Stream Analyzer software to calculate a composition for a concentrated solid nitrate salt and liquid waste stream. The calculation predicted the gas / condensed phase compositions as well as solid salt / saturated liquid compositions. The derived composition provides an estimate of the nitrate feedstream to WIPP for which kinetic measurements can be made. The ratio of salt to Swheat in drum 68660 contents was estimated through an overall mass balance on the parent and sibling drums. The RTR video provided independent confirmation concerning the volume of the mixture. The solid salt layer contains the majority of the salt at a ratio with Swheat that potentially could become exothermic.

Salt Composition Derived from Veazey Composition by Thermodynamic Modeling and Predicted Composition of Drum Contents

International Nuclear Information System (INIS)

Weisbrod, Kirk Ryan; Veirs, Douglas Kirk; Funk, David John; Clark, David Lewis

2016-01-01

This report describes the derivation of the salt composition from the Veazey salt stream analysis. It also provides an estimate of the proportions of the kitty litter, nitrate salt and neutralizer that was contained in drum 68660. While the actinide content of waste streams was judiciously followed in the 1980s in TA-55, no record of the salt composition could be found. Consequently, a salt waste stream produced from 1992 to 1994 and reported by Gerry Veazey provided the basis for this study. While chemical analysis of the waste stream was highly variable, an average analysis provided input to the Stream Analyzer software to calculate a composition for a concentrated solid nitrate salt and liquid waste stream. The calculation predicted the gas / condensed phase compositions as well as solid salt / saturated liquid compositions. The derived composition provides an estimate of the nitrate feedstream to WIPP for which kinetic measurements can be made. The ratio of salt to Swheat in drum 68660 contents was estimated through an overall mass balance on the parent and sibling drums. The RTR video provided independent confirmation concerning the volume of the mixture. The solid salt layer contains the majority of the salt at a ratio with Swheat that potentially could become exothermic.

Evidence for transgenerational metabolic programming in Drosophila

Directory of Open Access Journals (Sweden)

Jessica L. Buescher

2013-09-01

Worldwide epidemiologic studies have repeatedly demonstrated an association between prenatal nutritional environment, birth weight and susceptibility to adult diseases including obesity, cardiovascular disease and type 2 diabetes. Despite advances in mammalian model systems, the molecular mechanisms underlying this phenomenon are unclear, but might involve programming mechanisms such as epigenetics. Here we describe a new system for evaluating metabolic programming mechanisms using a simple, genetically tractable Drosophila model. We examined the effect of maternal caloric excess on offspring and found that a high-sugar maternal diet alters body composition of larval offspring for at least two generations, augments an obese-like phenotype under suboptimal (high-calorie feeding conditions in adult offspring, and modifies expression of metabolic genes. Our data indicate that nutritional programming mechanisms could be highly conserved and support the use of Drosophila as a model for evaluating the underlying genetic and epigenetic contributions to this phenomenon.

NASA-UVA Light Aerospace Alloy and Structures Technology Program (LA2ST)

Science.gov (United States)

Gangloff, Richard P.; Scully, John R.; Stoner, Glenn E.; Thornton, Earl A.; Wawner, Franklin E., Jr.; Wert, John A.

1993-01-01

The NASA-UVA Light Aerospace Alloy and Structures Technology (LA2ST) Program continues a high level of activity. Progress achieved between 1 Jan. and 30 Jun. 1993 is reported. The objective of the LA2ST Program is to conduct interdisciplinary graduate student research on the performance of next generation, light weight aerospace alloys, composites, and thermal gradient structures in collaboration with NASA-Langley researchers. The following projects are addressed: environmental fatigue of Al-Li-Cu alloys; mechanisms of localized corrosion and environmental fracture in Al-Cu-Li-Mg-Ag alloy X2095 and compositional variations; the effect of zinc additions on the precipitation and stress corrosion cracking behavior of alloy 8090; hydrogen interactions with Al-Li-Cu alloy 2090 and model alloys; metastable pitting of aluminum alloys; cryogenic fracture toughness of Al-Cu-Li + In alloys; the fracture toughness of Weldalite (TM); elevated temperature cracking of advanced I/M aluminum alloys; response of Ti-1100/SCS-6 composites to thermal exposure; superplastic forming of Weldalite (TM); research to incorporate environmental effects into fracture mechanics fatigue life prediction codes such as NASA FLAGRO; and thermoviscoplastic behavior.

Analytical Analysis and Field Test Investigation of Consolidation for CCSG Pile Composite Foundation in Soft Clay

Directory of Open Access Journals (Sweden)

Jin Yu

2013-01-01

Full Text Available Low-grade concrete-cored sand-gravel (CCSG pile composite foundation is a new kind of composite foundation for thick and soft clay ground treatment. An analytical solution was derived for calculating the consolidation process of this composite foundation by considering coefficients of horizontal permeability in smear zone, the radial flow within the sand-gravel shell, and the impervious property of concrete-cored pile. The results show that Terzaghi’s one-dimensional consolidation solution and the consolidation analytical solution of ordinary composite foundation were special cases of this solution. Curves of the average consolidation degree of the composite foundation under various nondimensional parameters were observed using the program based on the theoretical formula. Meanwhile, a series of in situ measurements including the settlement of pile and soil, the pore water pressure, and the total stress under embankment load were obtained on the CCSG pile composite foundation on a section of Zhenjiang-Liyang highway. The analyzed results show that the new style composite foundation patent technology has many advantages such as small differential postconstruction settlement (differential is not good, small is, reliable quality, high bearing capacity, and stability. And the consolidation of composite foundation is largely affected by the nondimensional parameters. The analytical solution is finally verified with the actual measurement data.

Solving a class of generalized fractional programming problems using the feasibility of linear programs.

Science.gov (United States)

Shen, Peiping; Zhang, Tongli; Wang, Chunfeng

2017-01-01

This article presents a new approximation algorithm for globally solving a class of generalized fractional programming problems (P) whose objective functions are defined as an appropriate composition of ratios of affine functions. To solve this problem, the algorithm solves an equivalent optimization problem (Q) via an exploration of a suitably defined nonuniform grid. The main work of the algorithm involves checking the feasibility of linear programs associated with the interesting grid points. It is proved that the proposed algorithm is a fully polynomial time approximation scheme as the ratio terms are fixed in the objective function to problem (P), based on the computational complexity result. In contrast to existing results in literature, the algorithm does not require the assumptions on quasi-concavity or low-rank of the objective function to problem (P). Numerical results are given to illustrate the feasibility and effectiveness of the proposed algorithm.

The Effects of the Nintendo Wii Exercise Program on Chronic Work-related Low Back Pain in Industrial Workers.

Science.gov (United States)

Park, Ji-Hyuk; Lee, Sang-Heon; Ko, Dae-Sik

2013-08-01

[Purpose] The purpose of this study was to investigate the effects of a Nintendo Wii exercise program on chronic work-related LBP compared with stability exercise. [Methods] Twenty-four workers participated in this study. All of the participants were diagnosed with chronic LBP by a physician. Participants were randomly assigned to three groups: a control group (CG), lumbar stabilization exercise group (LSE), and Nintendo Wii exercise group (NWE). Participants were treated 3 times a week for 8 weeks. Each session lasted 30 minutes. [Results] The results demonstrated that exercise programs improved significantly physical functions related to LBP. In health-related QOL, the Nintendo Wii exercise program significantly improved both the mental and physical health composites, but other groups had significant improvement only in the physical health composite. [Conclusion] The Nintendo Wii exercise program could be a biopsychosocial intervention for work-related LBP in factory workers.

School Oral Health Program in Kuwait.

Science.gov (United States)

Ariga, Jitendra; Al-Mutawa, Sabiha; Nazar, Huda

2014-01-01

The School Oral Health Program (SOHP), Kuwait, is a joint venture between the Ministry of Health, Kuwait, and Forsyth Institute, Cambridge, Mass., USA. This program provides oral health education, prevention and treatment to almost 280,000 public school children in Kuwait. Services are delivered through a system of center- and school-based clinics and preventive mobile teams. One of the recent developments is the effective use of portable dental units for the delivery of preventive care to children in schools without the need for children to go to dental clinics. Preventive procedures performed under this program are the biannual application of fluoride varnish and the placement of pit and fissure sealants on newly erupted permanent molars and premolars. During recent years, the SOHP has improved its coverage of children, with prevention up to 80%. This has resulted in a considerable reduction in treatment needs, which is evident from the reduced number of composite restorations performed under this program during the last 6 years. This indicates that the disease level is on a decline, which can be confirmed from the results of the ongoing National Oral Health Survey on Kuwaiti school children. © 2013 S. Karger AG, Basel.

Hydrogen storage compositions

Science.gov (United States)

Li, Wen; Vajo, John J.; Cumberland, Robert W.; Liu, Ping

2011-04-19

Compositions for hydrogen storage and methods of making such compositions employ an alloy that exhibits reversible formation/deformation of BH.sub.4.sup.- anions. The composition includes a ternary alloy including magnesium, boron and a metal and a metal hydride. The ternary alloy and the metal hydride are present in an amount sufficient to render the composition capable of hydrogen storage. The molar ratio of the metal to magnesium and boron in the alloy is such that the alloy exhibits reversible formation/deformation of BH.sub.4.sup.- anions. The hydrogen storage composition is prepared by combining magnesium, boron and a metal to prepare a ternary alloy and combining the ternary alloy with a metal hydride to form the hydrogen storage composition.

Refractory metal alloys and composites for space power systems

International Nuclear Information System (INIS)

Stephens, J.R.; Petrasek, D.W.; Titran, R.H.

1994-01-01

Space power requirements for future NASA and other United States missions will range from a few kilowatts to megawatts of electricity. Maximum efficiency is a key goal of any power system in order to minimize weight and size so that the space shuttle may be used a minimum number of times to put the power supply into orbit. Nuclear power has been identified as the primary power source to meet these high levels of electrical demand. One method to achieve maximum efficiency is to operate the power supply, energy conversion system, and related components at relatively high temperatures. NASA Lewis Research Center has undertaken a research program on advanced technology of refractory metal alloys and composites that will provide base line information for space power systems in the 1900's and the 21st century. Basic research on the tensile and creep properties of fibers, matrices, and composites will be discussed

Preliminary design study of advanced composite blade and hub and nonmechanical control system for the tilt-rotor aircraft. Volume 2: Project planning data

Science.gov (United States)

1980-01-01

Project planning data for a rotor and control system procurement and testing program for modifications to the XV-15 tilt-rotor research demonstrator aircraft is presented. The design, fabrication, and installation of advanced composite blades compatible with the existing hub, an advanced composite hub, and a nonmechanical control system are required.

A high protein diet (3.4 g/kg/d) combined with a heavy resistance training program improves body composition in healthy trained men and women--a follow-up investigation.

Science.gov (United States)

Antonio, Jose; Ellerbroek, Anya; Silver, Tobin; Orris, Steve; Scheiner, Max; Gonzalez, Adriana; Peacock, Corey A

2015-01-01

The consumption of a high protein diet (>4 g/kg/d) in trained men and women who did not alter their exercise program has been previously shown to have no significant effect on body composition. Thus, the purpose of this investigation was to determine if a high protein diet in conjunction with a periodized heavy resistance training program would affect indices of body composition, performance and health. Forty-eight healthy resistance-trained men and women completed this study (mean ± SD; Normal Protein group [NP n = 17, four female and 13 male]: 24.8 ± 6.9 yr; 174.0 ± 9.5 cm height; 74.7 ± 9.6 kg body weight; 2.4 ± 1.7 yr of training; High Protein group [HP n = 31, seven female and 24 male]: 22.9 ± 3.1 yr; 172.3 ± 7.7 cm; 74.3 ± 12.4 kg; 4.9 ± 4.1 yr of training). Moreover, all subjects participated in a split-routine, periodized heavy resistance-training program. Training and daily diet logs were kept by each subject. Subjects in the NP and HP groups were instructed to consume their baseline (~2 g/kg/d) and >3 g/kg/d of dietary protein, respectively. Subjects in the NP and HP groups consumed 2.3 and 3.4 g/kg/day of dietary protein during the treatment period. The NP group consumed significantly (p protein during the treatment period compared to their baseline intake. The HP group consumed more (p protein during the treatment period compared to their baseline intake. Furthermore, the HP group consumed significantly more (p protein compared to the NP group. There were significant time by group (p ≤ 0.05) changes in body weight (change: +1.3 ± 1.3 kg NP, -0.1 ± 2.5 HP), fat mass (change: -0.3 ± 2.2 kg NP, -1.7 ± 2.3 HP), and % body fat (change: -0.7 ± 2.8 NP, -2.4 ± 2.9 HP). The NP group gained significantly more body weight than the HP group; however, the HP group experienced a greater decrease in fat mass and % body fat. There was a significant time effect

The AHEC library program and consortia development in California.

Science.gov (United States)

Jensen, M A; Maddalena, B

1986-07-01

A brief history of the first Area Health Education Center (AHEC) Library Program in California is presented, with a description of methodology and results. The goals of this program were to develop and improve hospital library resources and services, to train hospital library personnel, and to promote resource sharing in a medically underserved area. The health sciences library consortium that evolved became a model for the ten other library consortia in the state. Based on AHEC's twelve years' experience with consortia, from 1973 to 1985, recommendations are made as to size, composition, leadership, outside funding, group participation, publicity, and linkages.

Software tools to aid Pascal and Ada program design

Energy Technology Data Exchange (ETDEWEB)

Jankowitz, H.T.

1987-01-01

This thesis describes a software tool which analyses the style and structure of Pascal and Ada programs by ensuring that some minimum design requirements are fulfilled. The tool is used in much the same way as a compiler is used to teach students the syntax of a language, only in this case issues related to the design and structure of the program are of paramount importance. The tool operates by analyzing the design and structure of a syntactically correct program, automatically generating a report detailing changes that need to be made in order to ensure that the program is structurally sound. The author discusses how the model gradually evolved from a plagiarism detection system which extracted several measurable characteristics in a program to a model that analyzed the style of Pascal programs. In order to incorporate more-sophistical concepts like data abstraction, information hiding and data protection, this model was then extended to analyze the composition of Ada programs. The Ada model takes full advantage of facilities offered in the language and by using this tool the standard and quality of written programs is raised whilst the fundamental principles of program design are grasped through a process of self-tuition.

Shaped fiber composites

Science.gov (United States)

Kinnan, Mark K.; Roach, Dennis P.

2017-12-05

A composite article is disclosed that has non-circular fibers embedded in a polymer matrix. The composite article has improved damage tolerance, toughness, bending, and impact resistance compared to composites having traditional round fibers.

NASA-UVA light aerospace alloy and structures technology program (LA(sup 2)ST)

Science.gov (United States)

Gangloff, Richard P.; Haviland, John K.; Herakovich, Carl T.; Pilkey, Walter D.; Pindera, Marek-Jerzy; Scully, John R.; Starke, Edgar A., Jr.; Stoner, Glenn E.; Thornton, Earl A.; Wawner, Franklin E., Jr.

1992-01-01

The general objective of the Light Aerospace Alloy and Structures Technology (LA(sup 2)ST) Program is to conduct interdisciplinary graduate student research on the performance of next generation, light weight aerospace alloys, composites, and thermal gradient structures in collaboration with Langley researchers. Specific technical objectives are established for each research project. We aim to produce relevant data and basic understanding of material behavior and microstructure, new monolithic and composite alloys, advanced processing methods, new solid and fluid mechanics analyses, measurement advances, and critically, a pool of educated graduate students for aerospace technologies. Four research areas are being actively investigated, including: (1) Mechanical and Environmental Degradation Mechanisms in Advanced Light Metals and Composites; (2) Aerospace Materials Science; (3) Mechanics of Materials and Composites for Aerospace Structures; and (4) Thermal Gradient Structures.

Impact of the energy-related inventions program on the national economy

Energy Technology Data Exchange (ETDEWEB)

Brown, M.A.; Morell, J.A.; Snell, S.A.; Kerley, C.R.

1987-01-01

The market entry, sales, and employment data presented in this paper suggest that ERIP has been able to efficiently produce positive economic impacts. It is likely that the documented successes of ERIP's inventors will be even greater as their projects mature and more current commercialization information is collected. Survey data presented elsewhere indicate that the ERIP financial support, endorsement, encouragement, and commercialization education are viewed by participants as the most important benefits of the program (Brown, Morell, Snell, Soderstrom, and Friggle, 1987). Other federal, state, and local programs might profit substantially from modelling the composition and delivery of their assistance after the Energy-Related Inventions Program.

Comparison between goal programming and cointegration approaches in enhanced index tracking

Science.gov (United States)

Lam, Weng Siew; Jamaan, Saiful Hafizah Hj.

2013-04-01

Index tracking is a popular form of passive fund management in stock market. Passive management is a buy-and-hold strategy that aims to achieve rate of return similar to the market return. Index tracking problem is a problem of reproducing the performance of a stock market index, without purchasing all of the stocks that make up the index. This can be done by establishing an optimal portfolio that minimizes risk or tracking error. An improved index tracking (enhanced index tracking) is a dual-objective optimization problem, a trade-off between maximizing the mean return and minimizing the tracking error. Enhanced index tracking aims to generate excess return over the return achieved by the index. The objective of this study is to compare the portfolio compositions and performances by using two different approaches in enhanced index tracking problem, which are goal programming and cointegration. The result of this study shows that the optimal portfolios for both approaches are able to outperform the Malaysia market index which is Kuala Lumpur Composite Index. Both approaches give different optimal portfolio compositions. Besides, the cointegration approach outperforms the goal programming approach because the cointegration approach gives higher mean return and lower risk or tracking error. Therefore, the cointegration approach is more appropriate for the investors in Malaysia.

Joining of thin thickness SiCf/SiC composites: research of a joining composition and of an associated elaboration process

International Nuclear Information System (INIS)

Jacques, E.

2012-01-01

The present work is part of the Fourth Generation Fast Reactors program. One of the key issues is the joining of the SiC f /SiC ceramic matrix composites (CMC) to seal the combustible cladding. At the present time, no chemical composition as a joint is refractive enough to face the expected operating temperatures. The aims of this study are the following: (1) the identification of a joining composition and its associated elaboration process answering the specifications, (2) the validation of a local and fast heating process and (3) the definition of mechanical tests to characterise these joinings. We describe the methodology and the results for joining SiC and SiC f /SiC substrates at solid and liquid state using metallic silicides. Joint integrity and joint strength can be improved by adding small SiC particles to the silicides powders. Chemical reactivity, wettability tests and thermomechanical properties analysis have been carried out on the joints. Cross sections of the assembly were prepared to study the joint/substrate chemical bonding, the cracking and the crack deflection in the vicinity of the interface. Also, one of the challenge consists in using a local heating at a high temperature (around 1800 C) for a short time to avoid the degradation of the composite structure. The assemblies have been then performed in an inductive furnace but in order to prepare the joining technology, trials of local heating have also been investigated with a CO 2 laser beam and a microwave generator. Finally, descriptions of the 4-points bending mechanical test used and the associated results are presented. (author) [fr

Advanced Industrial Materials (AIM) Program. Annual progress report, FY 1994

Energy Technology Data Exchange (ETDEWEB)

Sorrell, C.A.

1995-05-01

The Advanced Industrial Materials Program is a part of the Office of Industrial Technologies (OIT), Energy Efficiency and Renewable Energy in the Department of Energy. The mission of the AIM Program is to conduct applied research, development, and applications engineering work, in partnership with industry, to commercialize new or improved materials and materials processing methods that will improve energy efficiency, productivity, and competitiveness. AIM is responsible for identifying, supporting, and coordinating multidisciplinary projects to solve identified industrial needs and transferring the technology to the industrial sector. Program investigators in the DOE National Laboratories are working closely with approximately 100 companies, including 15 partners in Cooperative Research and Development Agreements. Work is being done in a wide variety of materials technologies, including intermetallic alloys, ceramic composites, metal composites, polymers, engineered porous materials, and surface modification. The Program supports other efforts in the Office of Industrial Technologies to assist the energy consuming process industries, including forest products, glass, steel, aluminum, foundries, chemicals, and refineries. To support OITs {open_quotes}Industries of the Future{close_quotes} initiatives and to improve the relevance of materials research, assessments of materials needs and opportunities in the process industries are being made. These assessments are being used for program planning and priority setting; support of work to satisfy those needs is being provided. Many new materials that have come into the marketplace in recent years, or that will be available for commercial use within a few more years, offer substantial benefits to society. This document contains 28 reports on advanced materials research. Individual reports have been processed separately for entry onto the Department of Energy databases.

Exercise program improved subjective dry eye symptoms for office workers

Directory of Open Access Journals (Sweden)

Sano K

2018-02-01

Full Text Available Kokoro Sano,1 Motoko Kawashima,1 Sayuri Takechi,2 Masaru Mimura,2 Kazuo Tsubota1 1Department of Ophthalmology, 2Department of Neuropsychiatry, Keio University School of Medicine, Tokyo, Japan Introduction: We investigated the benefits of a cognitive behavior therapy-based exercise program to reduce the dry eye symptoms of office workers. Materials and methods: We recruited 11 office workers with dry eye symptoms, aged 31–64 years, who voluntarily participated in group health guidance at a manufacturing company. Participants learned about the role of physical activity and exercise in enhancing wellness and performed an exercise program at home 3 days per week for 10 weeks. We estimated the indexes of body composition, dry eye symptoms, and psychological distress using the Dry Eye-Related Quality of Life Score and the World Health Organization’s Subjective Well-Being Inventory questionnaires pre- and postintervention. Results: The 10-week exercise program and the questionnaires were completed by 48.1% (39 of 81 of the participants. Body composition did not change pre- and postintervention. However, the average of the Dry Eye-Related Quality of Life Score scores in participants with subjective dry eye significantly improved after the intervention. Moreover, the World Health Organization’s Subjective Well-Being Inventory positive well-being score tended to increase after the intervention. Conclusion: In this study, we showed that a 10-week exercise program improved subjective dry eye symptoms of healthy office workers. Our study suggests that a cognitive behavior therapy-based exercise program can play an important role in the treatment of patients with dry eye disease. Keywords: dry eye, exercise, office workers, cognitive behavioral therapy

Using Genre to Bridge Research, Professional Writing, and Public Writing at University of North Dakota: A Program Profile

Science.gov (United States)

Basgier, Christopher

2017-01-01

To illustrate how genre pedagogy and public writing pedagogy can inform one another, this program profile describes the second-semester composition course at University of North Dakota, ENGL 130: College Composition II: Writing for Public Audiences. In this course, genre works as a rhetorical bridge across an interlinked sequence of research,…

Amorphous metal composites

International Nuclear Information System (INIS)

Byrne, M.A.; Lupinski, J.H.

1984-01-01

This patent discloses an improved amorphous metal composite and process of making the composite. The amorphous metal composite comprises amorphous metal (e.g. iron) and a low molecular weight thermosetting polymer binder. The process comprises placing an amorphous metal in particulate form and a thermosetting polymer binder powder into a container, mixing these materials, and applying heat and pressure to convert the mixture into an amorphous metal composite

Nano-composite materials

Science.gov (United States)

Lee, Se-Hee; Tracy, C. Edwin; Pitts, J. Roland

2010-05-25

Nano-composite materials are disclosed. An exemplary method of producing a nano-composite material may comprise co-sputtering a transition metal and a refractory metal in a reactive atmosphere. The method may also comprise co-depositing a transition metal and a refractory metal composite structure on a substrate. The method may further comprise thermally annealing the deposited transition metal and refractory metal composite structure in a reactive atmosphere.

body composition, and subjective assessments of training

Directory of Open Access Journals (Sweden)

J Giessing

2016-08-01

Full Text Available Most studies of resistance training (RT examine methods that do not resemble typical training practices of persons participating in RT. Ecologically valid RT programs more representative of such practices are seldom compared. This study compared two such approaches to RT. Thirty participants (males, n=13; females, n=17 were randomised to either a group performing low volume ‘High Intensity Training’ (HIT; n=16 or high volume ‘Body-building’ (3ST; n=14 RT methods 2x/week for 10 weeks. Outcomes included muscular performance, body composition, and participant’s subjective assessments. Both HIT and 3ST groups improved muscular performance significantly (as indicated by 95% confidence intervals with large effect sizes (ES; 0.97 to 1.73 and 0.88 to 1.77 respectively. HIT had significantly greater muscular performance gains for 3 of 9 tested exercises compared with 3ST (p < 0.05 and larger effect sizes for 8 of 9 exercises. Body composition did not significantly change in either group. However, effect sizes for whole body muscle mass changes were slightly more favourable in the HIT group compared with the 3ST group (0.27 and -0.34 respectively in addition to whole body fat mass (0.03 and 0.43 respectively and whole body fat percentage (-0.10 and -0.44 respectively. Significant muscular performance gains can be produced using either HIT or 3ST. However, muscular performance gains may be greater when using HIT. Future research should look to identify which components of ecologically valid RT programs are primarily responsible for these differences in outcome.

Design, evaluation, and fabrication of low-cost composite blades for intermediate-size wind turbines

Science.gov (United States)

Weingart, O.

1981-01-01

Low cost approaches for production of 60 ft long glass fiber/resin composite rotor blades for the MOD-OA wind turbine were identified and evaluated. The most cost-effective configuration was selected for detailed design. Subelement and subscale specimens were fabricated for testing to confirm physical and mechanical properties of the composite blade materials, to develop and evaluate blade fabrication techniques and processes, and to confirm the structural adequacy of the root end joint. Full-scale blade tooling was constructed and a partial blade for tool and process tryout was built. Then two full scale blades were fabricated and delivered to NASA-LeRC for installation on a MOD-OA wind turbine at Clayton, New Mexico for operational testing. Each blade was 60 ft. long with 4.5 ft. chord at root end and 2575 lbs weight including metal hub adapter. The selected blade configuration was a three cell design constructed using a resin impregnated glass fiber tape winding process that allows rapid wrapping of primarily axially oriented fibers onto a tapered mandrel, with tapered wall thickness. The ring winder/transverse filament tape process combination was used for the first time on this program to produce entire rotor blade structures. This approach permitted the complete blade to be wound on stationary mandrels, an improvement which alleviated some of the tooling and process problems encountered on previous composite blade programs.

Composite Dos Attack Model

Directory of Open Access Journals (Sweden)

Simona Ramanauskaitė

2012-04-01

Full Text Available Preparation for potential threats is one of the most important phases ensuring system security. It allows evaluating possible losses, changes in the attack process, the effectiveness of used countermeasures, optimal system settings, etc. In cyber-attack cases, executing real experiments can be difficult for many reasons. However, mathematical or programming models can be used instead of conducting experiments in a real environment. This work proposes a composite denial of service attack model that combines bandwidth exhaustion, filtering and memory depletion models for a more real representation of similar cyber-attacks. On the basis of the introduced model, different experiments were done. They showed the main dependencies of the influence of attacker and victim’s properties on the success probability of denial of service attack. In the future, this model can be used for the denial of service attack or countermeasure optimization.

Computational composites

DEFF Research Database (Denmark)

Vallgårda, Anna K. A.; Redström, Johan

2007-01-01

Computational composite is introduced as a new type of composite material. Arguing that this is not just a metaphorical maneuver, we provide an analysis of computational technology as material in design, which shows how computers share important characteristics with other materials used in design...... and architecture. We argue that the notion of computational composites provides a precise understanding of the computer as material, and of how computations need to be combined with other materials to come to expression as material. Besides working as an analysis of computers from a designer’s point of view......, the notion of computational composites may also provide a link for computer science and human-computer interaction to an increasingly rapid development and use of new materials in design and architecture....

Opportunities for the LWR ATF materials development program to contribute to the LBE-cooled ADS materials qualification program

Energy Technology Data Exchange (ETDEWEB)

Gong, Xing, E-mail: gongxingzfl@hotmail.com [Department of ATF R& D, Nuclear Fuel Research and Development Center, China Nuclear Power Technology Research Institute Co., Ltd., China General Nuclear Power Corporation (CGN), Shenzhen, 518026 (China); Li, Rui, E-mail: li-rui@cgnpc.com.cn [Department of ATF R& D, Nuclear Fuel Research and Development Center, China Nuclear Power Technology Research Institute Co., Ltd., China General Nuclear Power Corporation (CGN), Shenzhen, 518026 (China); Sun, Maozhou; Ren, Qisen [Department of ATF R& D, Nuclear Fuel Research and Development Center, China Nuclear Power Technology Research Institute Co., Ltd., China General Nuclear Power Corporation (CGN), Shenzhen, 518026 (China); Liu, Tong, E-mail: liutong@cgnpc.com.cn [Department of ATF R& D, Nuclear Fuel Research and Development Center, China Nuclear Power Technology Research Institute Co., Ltd., China General Nuclear Power Corporation (CGN), Shenzhen, 518026 (China); Short, Michael P., E-mail: hereiam@mit.edu [Department of Nuclear Science and Engineering, Massachusetts Institute of Technology (MIT), Cambridge, MA, 02139 (United States)

2016-12-15

Accelerator-driven systems (ADS) are a promising approach for nuclear waste disposal. Nevertheless, the principal candidate materials proposed for ADS construction, such as the ferritic/martensitic steel, T91, and austenitic stainless steels, 316L and 15-15Ti, are not fully compatible with the liquid lead-bismuth eutectic (LBE) coolant. Under some operating conditions, liquid metal embrittlement (LME) or liquid metal corrosion (LMC) may occur in these steels when exposed to LBE. These environmentally-induced material degradation effects pose a threat to ADS reactor safety, as failure of the materials could initiate a severe accident, in which fission products are released into the coolant. Meanwhile, parallel efforts to develop accident-tolerant fuels (ATF) in light water reactors (LWRs) could provide both general materials design philosophies and specific material solutions to the ADS program. In this paper, the potential contributions of the ATF materials development program to the ADS materials qualification program are evaluated and discussed in terms of service conditions and materials performance requirements. Several specific areas where coordinated development may benefit both programs, including composite materials and selected coatings, are discussed. - Highlights: • ATF materials developed for LWRs could be candidate materials for the LBE-cooled ADS program. • Similar material design and protection philosophies are utilized in both programs. • Unique challenges of LBE-cooled ADS systems could possibly be addressed by LWR ATF materials. • More coordinated testing should be performed between the ATF and ADS programs.

Computer program for stresses and buckling of heated composite-stiffened panels and other structures (BUCLASP 3)

Science.gov (United States)

Viswanathan, A. V.; Tamekuni, M.; Tripp, L. L.

1974-01-01

General-purpose program is intended for thermal stress and instability analyses of structures such as axially-stiffened curved panels. Two types of instability analyses can be effected by program: (1) thermal buckling with temperature variation as specified and (2) buckling due to in-plane biaxial loading.

Confirmatory Composite Analysis

NARCIS (Netherlands)

Schuberth, Florian; Henseler, Jörg; Dijkstra, Theo K.

2018-01-01

We introduce confirmatory composite analysis (CCA) as a structural equation modeling technique that aims at testing composite models. CCA entails the same steps as confirmatory factor analysis: model specification, model identification, model estimation, and model testing. Composite models are

Two-boson composites

DEFF Research Database (Denmark)

Tichy, Malte C.; Bouvrier, P. Alexander; Mølmer, Klaus

2013-01-01

Composite bosons made of two bosonic constituents exhibit deviations from ideal bosonic behavior due to their substructure. This deviation is reflected by the normalization ratio of the quantum state of N composites. We find a set of saturable, efficiently evaluable bounds for this indicator, which...... quantifies the bosonic behavior of composites via the entanglement of their constituents. We predict an abrupt transition between ordinary and exaggerated bosonic behavior in a condensate of two-boson composites....

Correlation between Composition and Properties of Composite Material Based on Scrap Tires

OpenAIRE

Mālers, L; Plēsuma, R; Ločmele, L; Kalniņš, M

2010-01-01

Purpose of present work is to investigate mechanical and insulation properties of the composite material based on scrap tires and polyurethane-type binder in correlation with composition of composite material. The studies of material’s hardness must be considered as an express-method for estimation of the selected mechanical properties (E and ccompressive stress) of the composite material without direct experimental testing of given parameters. It was shown that composite material must be r...

Childhood obesity treatment; Effects on BMI SDS, body composition, and fasting plasma lipid concentrations

DEFF Research Database (Denmark)

Nielsen, Tenna Ruest Haarmark; Fonvig, Cilius Esmann; Dahl, Maria

2018-01-01

Objective The body mass index (BMI) standard deviation score (SDS) may not adequately reflect changes in fat mass during childhood obesity treatment. This study aimed to investigate associations between BMI SDS, body composition, and fasting plasma lipid concentrations at baseline and during......, and 80% improved their lipid concentrations. Conclusion Reductions in the degree of obesity during multidisciplinary childhood obesity treatment are accompanied by improvements in body composition and fasting plasma lipid concentrations. Even in individuals increasing their BMI SDS, body composition...... childhood obesity treatment. Methods 876 children and adolescents (498 girls) with overweight/obesity, median age 11.2 years (range 1.6±21.7), and median BMI SDS 2.8 (range 1.3±5.7) were enrolled in a multidisciplinary outpatient treatment program and followed for a median of 1.8 years (range 0...

Extension-torsion coupling behavior of advanced composite tilt-rotor blades

Science.gov (United States)

Kosmatka, J. B.

1989-01-01

An analytic model was developed to study the extension-bend-twist coupling behavior of an advanced composite helicopter or tilt-rotor blade. The outer surface of the blade is defined by rotating an arbitrary cross section about an initial twist axis. The cross section can be nonhomogeneous and composed of generally anisotropic materials. The model is developed based upon a three dimensional elasticity approach that is recast as a coupled two-dimensional boundary value problem defined in a curvilinear coordinate system. Displacement solutions are written in terms of known functions that represent extension, bending, and twisting and unknown functions for local cross section deformations. The unknown local deformation functions are determined by applying the principle of minimum potential energy to the discretized two-dimensional cross section. This is an application of the Ritz method, where the trial function family is the displacement field associated with a finite element (8-node isoparametric quadrilaterals) representation of the section. A computer program was written where the cross section is discretized into 8-node quadrilateral subregions. Initially the program was verified using previously published results (both three-dimensional elasticity and technical beam theory) for pretwisted isotropic bars with an elliptical cross section. In addition, solid and thin-wall multi-cell NACA-0012 airfoil sections were analyzed to illustrate the pronounced effects that pretwist, initial twist axis location, and spar location has on coupled behavior. Currently, a series of advanced composite airfoils are being modeled in order to assess how the use of laminated composite materials interacts with pretwist to alter the coupling behavior of the blade. These studies will investigate the use of different ply angle orientations and the use of symmetric versus unsymmetric laminates.

Performance Investigation of a Full-Scale Hybrid Composite Bull Gear

Science.gov (United States)

LaBerge, Kelsen; Handschuh, Robert; Roberts, Gary; Thorp, Scott

2016-01-01

Hybrid composite gears have been investigated as a weight saving technology for rotorcraft transmissions. These gears differ from conventional steel gears in that the structural material between the shaft interface and the gear rim is replaced with a lightweight carbon fiber composite. The work discussed here is an extension of previous coupon level hybrid gear tests to a full-scale bull gear. The NASA Glenn Research Center High-Speed Helical Gear Rig was modified for this program allowing several hybrid gear web configurations to be tested while utilizing the same gear rim. Testing was performed on both a baseline (steel) web configuration and a hybrid (steel-composite)configuration. Vibration, orbit and temperature data were recorded and compared between configurations. Vibration levels did not differ greatly between the hybrid and steel configurations, nor did temperature differential between inlet and outlet. While orbit shape displayed differences between the hybrid and baseline configurations, the general overall amplitude was comparable. The hybrid configuration discussed here successfully ran at 3300 hp(2,460 kW), however, progressive growth of the orbit while running at this test condition discontinued the test. Researchers continue to search for the cause of this orbit shift.

Validity of air-displacement plethysmography in the assessment of body composition changes in a 16-month weight loss program

Directory of Open Access Journals (Sweden)

Hull Holly R

2006-08-01

Full Text Available Abstract Objective To compare the accuracy of air displacement plethysmography (ADP and dual energy x-ray absorptionmetry (DXA in tracking changes in body composition after a 16 month weight loss intervention in overweight and obese females. Methods 93 healthy female subjects (38.9 ± 5.7 yr, 159.8 ± 5.6 cm, 76.7 ± 9.9 kg, 30.0 ± 3.4 kg/m2 completed a 16 month weight loss intervention. Eligible subjects attended 15 treatment sessions occurring over the course of 4 months with educational content including topics relating to physical activity and exercise, diet and eating behavior, and behavior modification. In the remaining 12 months, subjects underwent a lifestyle program designed to increase physical activity and improve eating habits. Before and after the intervention, subjects had their percent body fat (%fat, fat mass (FM, and fat-free mass (FFM assessed by DXA and ADP. Results Significant differences (p ≤ 0.001 were found between DXA and ADP at baseline %fat (46.0 % fat vs. 42.0 % fat, FM (35.3 kg vs. 32.5 kg and FFM (40.8 kg vs. 44.2 kg as well as at post intervention for %fat (42.1% fat vs. 38.3 % fat, FM (30.9 kg vs. 28.4 kg and FFM (41.7 kg vs. 44.7 kg. At each time point, ADP %fat and total FM was significantly lower (p ≤ 0.001 than DXA while FFM was significantly higher (p ≤ 0.001. However, both techniques tracked %fat changes similarly considering that there were no differences between the two means. Furthermore, a Bland-Altman analysis was performed and no significant bias was observed, thus demonstrating the ability of ADP to measure body fat across a wide range of fatness. Conclusion At baseline and post weight loss, a significant difference was found between ADP and DXA. However, the results indicate both methods are highly related and track changes in %fat similarly after a weight loss program in overweight and obese females. Additionally, the mean changes in %fat were similar between the two techniques, suggesting

Analysis of composition and microstructural uniformity of hybrid glass/carbon fibre composites

DEFF Research Database (Denmark)

Beauson, Justine; Markussen, Christen Malte; Madsen, Bo

2013-01-01

level are investigated. The different levels of compositions in the composites are defined and experimentally determined. The composite volume fractions are determined using an image analysis based procedure. The global fibre volume fractions are determined using a gravimetrical based method. The local...... methods, a standard deviation based method and a fast Fourier transform method, are used to quantify the difference in microstructural uniformity between composites, and to detect and quantify any repeating pattern in the composite microstructure....

Saul: Towards Declarative Learning Based Programming.

Science.gov (United States)

Kordjamshidi, Parisa; Roth, Dan; Wu, Hao

2015-07-01

We present Saul , a new probabilistic programming language designed to address some of the shortcomings of programming languages that aim at advancing and simplifying the development of AI systems. Such languages need to interact with messy, naturally occurring data, to allow a programmer to specify what needs to be done at an appropriate level of abstraction rather than at the data level, to be developed on a solid theory that supports moving to and reasoning at this level of abstraction and, finally, to support flexible integration of these learning and inference models within an application program. Saul is an object-functional programming language written in Scala that facilitates these by (1) allowing a programmer to learn, name and manipulate named abstractions over relational data; (2) supporting seamless incorporation of trainable (probabilistic or discriminative) components into the program, and (3) providing a level of inference over trainable models to support composition and make decisions that respect domain and application constraints. Saul is developed over a declaratively defined relational data model, can use piecewise learned factor graphs with declaratively specified learning and inference objectives, and it supports inference over probabilistic models augmented with declarative knowledge-based constraints. We describe the key constructs of Saul and exemplify its use in developing applications that require relational feature engineering and structured output prediction.

Concrete compositions and methods

Science.gov (United States)

Chen, Irvin; Lee, Patricia Tung; Patterson, Joshua

2015-06-23

Provided herein are compositions, methods, and systems for cementitious compositions containing calcium carbonate compositions and aggregate. The compositions find use in a variety of applications, including use in a variety of building materials and building applications.

Crossfit-based high-intensity power training improves maximal aerobic fitness and body composition.

Science.gov (United States)

Smith, Michael M; Sommer, Allan J; Starkoff, Brooke E; Devor, Steven T

2013-11-01

The purpose of this study was to examine the effects of a crossfit-based high-intensity power training (HIPT) program on aerobic fitness and body composition. Healthy subjects of both genders (23 men, 20 women) spanning all levels of aerobic fitness and body composition completed 10 weeks of HIPT consisting of lifts such as the squat, deadlift, clean, snatch, and overhead press performed as quickly as possible. Additionally, this crossfit-based HIPT program included skill work for the improvement of traditional Olympic lifts and selected gymnastic exercises. Body fat percentage was estimated using whole-body plethysmography, and maximal aerobic capacity (VO2max) was measured by analyzing expired gasses during a Bruce protocol maximal graded treadmill test. These variables were measured again after 10 weeks of training and compared for significant changes using a paired t-test. Results showed significant (p < 0.05) improvements of VO2max in men (43.10 ± 1.40 to 48.96 ± 1.42 ml · kg · min) and women (35.98 ± 1.60 to 40.22 ± 1.62 ml · kg · min) and decreased body fat percentage in men (22.2 ± 1.3 to 18.0 ± 1.3) and women (26.6 ± 2.0 to 23.2 ± 2.0). These improvements were significant across all levels of initial fitness. Significant correlations between absolute oxygen consumption and oxygen consumption relative to body weight was found in both men (r = 0.83, p < 0.001) and women (r = 0.94, p < 0.001), indicating that HIPT improved VO2max scaled to body weight independent of changes to body composition. Our data show that HIPT significantly improves VO2max and body composition in subjects of both genders across all levels of fitness.

Engineering method to build the composite structure ply database

Directory of Open Access Journals (Sweden)

Qinghua Shi

Full Text Available In this paper, a new method to build a composite ply database with engineering design constraints is proposed. This method has two levels: the core stacking sequence design and the whole stacking sequence design. The core stacking sequences are obtained by the full permutation algorithm considering the ply ratio requirement and the dispersion character which characterizes the dispersion of ply angles. The whole stacking sequences are the combinations of the core stacking sequences. By excluding the ply sequences which do not meet the engineering requirements, the final ply database is obtained. One example with the constraints that the total layer number is 100 and the ply ratio is 30:60:10 is presented to validate the method. This method provides a new way to set up the ply database based on the engineering requirements without adopting intelligent optimization algorithms. Keywords: Composite ply database, VBA program, Structure design, Stacking sequence

Advanced Industrial Materials (AIM) Program: Compilation of project summaries and significant accomplishments, FY 1995

Energy Technology Data Exchange (ETDEWEB)

NONE

1996-04-01

In many ways, the Advanced Industrial Materials (AIM) Program underwent a major transformation in Fiscal Year 1995 and these changes have continued to the present. When the Program was established in 1990 as the Advanced Industrial Concepts (AIC) Materials Program, the mission was to conduct applied research and development to bring materials and processing technologies from the knowledge derived from basic research to the maturity required for the end use sectors for commercialization. In 1995, the Office of Industrial Technologies (OIT) made radical changes in structure and procedures. All technology development was directed toward the seven ``Vision Industries`` that use about 80% of industrial energy and generated about 90% of industrial wastes. The mission of AIM has, therefore, changed to ``Support development and commercialization of new or improved materials to improve productivity, product quality, and energy efficiency in the major process industries.`` Though AIM remains essentially a National Laboratory Program, it is essential that each project have industrial partners, including suppliers to, and customers of, the seven industries. Now, well into FY 1996, the transition is nearly complete and the AIM Program remains reasonably healthy and productive, thanks to the superb investigators and Laboratory Program Managers. This report contains the technical details of some very remarkable work by the best materials scientists and engineers in the world. Subject areas covered are: advanced metals and composites; advanced ceramics and composites; polymers and biobased materials; and new materials and processes.

Efeito da atividade física programada sobre a composição corporal em escolares adolescentes Influence of programmed physical activity on body composition among adolescent students

Directory of Open Access Journals (Sweden)

Edson S. Farias

2009-02-01

Full Text Available OBJETIVO: Verificar o efeito da atividade física programada na escola sobre a composição corporal em escolares adolescentes durante 1 ano letivo. MÉTODOS: Amostra foi composta por 383 alunos, divididos em dois grupos: caso com 186 (96 meninos e 90 meninas e controle com 197 (108 meninos e 89 meninas, com idade entre 10 e 15 anos. Trata-se de estudo de intervenção com pré e pós-teste, no qual o grupo caso foi submetido a atividade física programada e o grupo-controle a aulas convencionais de educação física escolar. A composição corporal foi avaliada por medidas antropométricas e cálculos de índice de massa corporal, percentual de gordura e massas gorda e magra. RESULTADOS: O grupo caso apresentou estabilidade na prega cutânea subescapular, índice de massa corporal, percentual de gordura e na massa gorda; redução significativa na prega cutânea triciptal, perímetro do abdome nas meninas e aumento significativo dos perímetros do braço, cintura e panturrilha e da massa magra. No grupo-controle houve aumento do índice de massa corporal, prega cutânea triciptal, perímetro do abdome e da massa gorda nas meninas. O grupo caso apresentou diminuição significativa na proporção de sobrepesos e obesos no pós em relação ao pré-teste, o mesmo não ocorrendo no grupo-controle. CONCLUSÃO: A atividade física programada resultou em melhoria e manutenção nas variáveis da composição corporal e redução da frequência de sobrepeso e obesidade no grupo que sofreu intervenção.OBJECTIVE: To verify the influence of programmed physical activity on body composition among adolescent students during 1 school year. METHODS: The sample included 383 students (age range: 10 to 15years separated into two groups: 186 cases (96 male and 90 female and 197 controls (108 male and 89 female. This was an intervention study with pre- and post-test assessments in which interventions consisted of programmed physical activity; the control group

Fabrication of fuel elements on the basis of increased concentration fuel composition

International Nuclear Information System (INIS)

Alexandrov, A.B.; Afanasiev, V.L.; Enin, A.A.; Suprun, V.B.

2004-01-01

As a part of Russian Program RERTR Reduced Enrichment for Research and Test Reactors), at NCCP, Inc. jointly with the State Scientific Centre VNIINM the mastering in industrial environment of design and fabrication process of fuel elements (FE) with increased concentration fuel compositions is performed. Fuel elements with fuel composition on the basis of dioxide uranium with nearly 4 g/cm 3 fuel concentration have been produced thus confirming the principal possibility of fuel enrichment reduction down to 20% for research reactors which were built up according to the projects of the former USSR, by increasing the oxide fuel concentration in fuel assemblies (FAs). The form and geometrical dimensions of FEs and FAs shall remain unchanged, only uranium mass in FA shall be increased. (author)

Compositional Advantage and Strategy

DEFF Research Database (Denmark)

Li, Xin

advantage is redefined as the attractiveness of the composition of the producer’s offering in terms of scope and perceived value/price ratio. I identify five ways or basic compositional strategies to improve the value/price ratio. A firm may have an overall compositional strategy that is composed of some......In this paper, I first critique the composition-based view of Yadong Luo and John Child for understanding how resource-poor firms survive and thrive. To remedy the deficiencies in their perspective, I then propose a dynamic theory of compositional advantage and strategy. Here, the compositional...... or all of the five basic compositional strategies. I argue there are three indispensable key success factors for a composition-based competition, i.e., aspiration (ambition-position asymmetry), attitude (being ALERT), and action (turning asymmetry into advantage). I also discuss the particular relevance...

An X-Shooter composite of bright 1 < z < 2 quasars from UV to infrared

Science.gov (United States)

Selsing, J.; Fynbo, J. P. U.; Christensen, L.; Krogager, J.-K.

2016-01-01

Quasi-stellar object (QSO) spectral templates are important both to QSO physics and for investigations that use QSOs as probes of intervening gas and dust. However, combinations of various QSO samples obtained at different times and with different instruments so as to expand a composite and to cover a wider rest frame wavelength region may create systematic effects, and the contribution from QSO hosts may contaminate the composite. We have constructed a composite spectrum from luminous blue QSOs at 1 contamination. Assuming a power-law continuum for the composite we find a spectral slope of αλ = 1.70 ± 0.01, which is steeper than previously found in the literature. We attribute the differences to our broader spectral wavelength coverage, which allows us to effectively avoid fitting any regions that are affected either by strong QSO emissions lines (e.g., Balmer lines and complex [Fe II] blends) or by intrinsic host galaxy emission. Finally, we demonstrate the application of the QSO composite spectrum for evaluating the reddening in other QSOs. Based on observations made with telescopes at the European Southern Observatory at La Silla/Paranal, Chile under program 090.A-0147(A).The quasar composite is only available at the CDS via anonymous ftp to http://cdsarc.u-strasbg.fr (ftp://130.79.128.5) or via http://cdsarc.u-strasbg.fr/viz-bin/qcat?J/A+A/585/A87 Source code and composite is also made public at http://https://github.com/jselsing/QuasarComposite

Composite Behavior of Insulated Concrete Sandwich Wall Panels Subjected to Wind Pressure and Suction

Directory of Open Access Journals (Sweden)

Insub Choi

2015-03-01

Full Text Available A full-scale experimental test was conducted to analyze the composite behavior of insulated concrete sandwich wall panels (ICSWPs subjected to wind pressure and suction. The experimental program was composed of three groups of ICSWP specimens, each with a different type of insulation and number of glass-fiber-reinforced polymer (GFRP shear grids. The degree of composite action of each specimen was analyzed according to the load direction, type of the insulation, and number of GFRP shear grids by comparing the theoretical and experimental values. The failure modes of the ICSWPs were compared to investigate the effect of bonds according to the load direction and type of insulation. Bonds based on insulation absorptiveness were effective to result in the composite behavior of ICSWP under positive loading tests only, while bonds based on insulation surface roughness were effective under both positive and negative loading tests. Therefore, the composite behavior based on surface roughness can be applied to the calculation of the design strength of ICSWPs with continuous GFRP shear connectors.

Efficient QoS-aware Service Composition

Science.gov (United States)

Alrifai, Mohammad; Risse, Thomas

Web service composition requests are usually combined with endto-end QoS requirements, which are specified in terms of non-functional properties (e.g. response time, throughput and price). The goal of QoS-aware service composition is to find the best combination of services such that their aggregated QoS values meet these end-to-end requirements. Local selection techniques are very efficient but fail short in handling global QoS constraints. Global optimization techniques, on the other hand, can handle global constraints, but their poor performance render them inappropriate for applications with dynamic and real-time requirements. In this paper we address this problem and propose a solution that combines global optimization with local selection techniques for achieving a better performance. The proposed solution consists of two steps: first we use mixed integer linear programming (MILP) to find the optimal decomposition of global QoS constraints into local constraints. Second, we use local search to find the best web services that satisfy these local constraints. Unlike existing MILP-based global planning solutions, the size of the MILP model in our case is much smaller and independent on the number of available services, yields faster computation and more scalability. Preliminary experiments have been conducted to evaluate the performance of the proposed solution.

The Composer's Program Note for Newly Written Classical Music: Content and Intentions.

Science.gov (United States)

Blom, Diana M; Bennett, Dawn; Stevenson, Ian

2016-01-01

In concerts of western classical music the provision of a program note is a widespread practice dating back to the 18th century and still commonly in use. Program notes tend to inform listeners and performers about historical context, composer biographical details, and compositional thinking. However, the scant program note research conducted to date reveals that program notes may not foster understanding or enhance listener enjoyment as previously assumed. In the case of canonic works, performers and listeners may already be familiar with much of the program note information. This is not so in the case of newly composed works, which formed the basis of the exploratory study reported here. This article reports the views of 17 living contemporary composers on their writing of program notes for their own works. In particular, the study sought to understand the intended recipient, role and the content of composer-written program notes. Participating composers identified three main roles for their program notes: to shape a performer's interpretation of the work; to guide, engage or direct the listener and/or performer; and as collaborative mode of communication between the composer, performer, and listener. For some composers, this collaboration was intended to result in "performative listening" in which listeners were actively engaged in bringing each composition to life. This was also described as a form of empathy that results in the co-construction of the musical experience. Overall, composers avoided giving too much personal information and they provided performers with more structural information. However, composers did not agree on whether the same information should be provided to both performers and listeners. Composers' responses problematize the view of a program note as a simple statement from writer to recipient, indicating instead a more complex set of relations at play between composer, performer, listener, and the work itself. These relations are

Composition: Four Rules

DEFF Research Database (Denmark)

Bergstrøm-Nielsen, Carl

2013-01-01

Cue Rondo is an open composition to be realised by improvising musicians. See more about my composition practise in the entry "Composition - General Introduction". This work is licensed under a Creative Commons "by-nc" License. You may for non-commercial purposes use and distribute it, performanc...

Method and apparatus for real-time measurement of fuel gas compositions and heating values

Science.gov (United States)

Zelepouga, Serguei; Pratapas, John M.; Saveliev, Alexei V.; Jangale, Vilas V.

2016-03-22

An exemplary embodiment can be an apparatus for real-time, in situ measurement of gas compositions and heating values. The apparatus includes a near infrared sensor for measuring concentrations of hydrocarbons and carbon dioxide, a mid infrared sensor for measuring concentrations of carbon monoxide and a semiconductor based sensor for measuring concentrations of hydrogen gas. A data processor having a computer program for reducing the effects of cross-sensitivities of the sensors to components other than target components of the sensors is also included. Also provided are corresponding or associated methods for real-time, in situ determination of a composition and heating value of a fuel gas.

Composite quarterly technical report: long-term high-level waste technology, October-December 1980

International Nuclear Information System (INIS)

Cornman, W.R.

1981-04-01

The technical information in this report summarizes work performed at participating sites to immobilize high-level radioactive wastes. The areas reported are in: program management and support; waste preparation; waste fixation; and final handling. Majority of the studies were in the area of waste fixation, some of which are: leaching tests of ceramic forms, high silica glass, graphite powder and other carbon preparations; viscosity measurements for a range of waste-glass compositions from references borosilicate glass to high-alumina glasses; neutron activation analysis for measuring leach rates; preparation of SYNROC D spheres; formulations for preparing ceramics from defense waste composition; development of a pilot-scale glass melter, and kinetic studies of slag formation in glass melters

Chemical vapor infiltration of TiB{sub 2} fibrous composites

Energy Technology Data Exchange (ETDEWEB)

Besmann, T.M. [Oak Ridge National Lab., TN (United States)

1997-04-01

This program is designed to develop a Hall-Heroult aluminum smelting cathode with substantially improved properties. The carbon cathodes in current use require significant anode-to-cathode spacing in order to prevent shorting, causing significant electrical inefficiencies. This is due to the non-wettability of carbon by aluminum which causes instability in the cathodic aluminum pad. It is suggested that a fiber reinforced-TiB{sub 2} matrix composite would have the requisite wettability, strength, strain-to-failure, cost, and lifetime to solve this problem. The approach selected to fabricate such a cathode material is chemical vapor infiltration (CVI). This process produces high purity matrix TiB{sub 2} without damaging the relatively fragile fibers. The program is designed to evaluate potential fiber reinforcements, fabricate test specimens, and scale the process to provide demonstration components.

What Are We Doing? A Survey of United States Nephrology Fellowship Program Directors.

Science.gov (United States)

Liebman, Scott E; Moore, Catherine A; Monk, Rebeca D; Rizvi, Mahrukh S

2017-03-07

Interest in nephrology has been declining in recent years. Long work hours and a poor work/life balance may be partially responsible, and may also affect a fellowship's educational mission. We surveyed nephrology program directors using a web-based survey in order to define current clinical and educational practice patterns and identify areas for improvement. Our survey explored fellowship program demographics, fellows' workload, call structure, and education. Program directors were asked to estimate the average and maximum number of patients on each of their inpatient services, the number of patients seen by fellows in clinic, and to provide details regarding their overnight and weekend call. In addition, we asked about number of and composition of didactic conferences. Sixty-eight out of 148 program directors responded to the survey (46%). The average number of fellows per program was approximately seven. The busiest inpatient services had a mean of 21.5±5.9 patients on average and 33.8±10.7 at their maximum. The second busiest services had an average and maximum of 15.6±6.0 and 24.5±10.8 patients, respectively. Transplant-only services had fewer patients than other service compositions. A minority of services (14.5%) employed physician extenders. Fellows most commonly see patients during a single weekly continuity clinic, with a typical fellow-to-faculty ratio of 2:1. The majority of programs do not alter outpatient responsibilities during inpatient service time. Most programs (approximately 75%) divided overnight and weekend call responsibilities equally between first year and more senior fellows. Educational practices varied widely between programs. Our survey underscores the large variety in workload, practice patterns, and didactics at different institutions and provides a framework to help improve the service/education balance in nephrology fellowships. Copyright © 2017 by the American Society of Nephrology.

Advanced Environmental Barrier Coating Development for SiC-SiC Ceramic Matrix Composite Components

Science.gov (United States)

Zhu, Dongming; Harder, Bryan; Hurst, Janet B.; Halbig, Michael Charles; Puleo, Bernadette J.; Costa, Gustavo; Mccue, Terry R.

2017-01-01

This presentation reviews the NASA advanced environmental barrier coating (EBC) system development for SiC-SiC Ceramic Matrix Composite (CMC) combustors particularly under the NASA Environmentally Responsible Aviation, Fundamental Aeronautics and Transformative Aeronautics Concepts Programs. The emphases have been placed on the current design challenges of the 2700-3000F capable environmental barrier coatings for low NOX emission combustors for next generation turbine engines by using advanced plasma spray based processes, and the coating processing and integration with SiC-SiC CMCs and component systems. The developments also have included candidate coating composition system designs, degradation mechanisms, performance evaluation and down-selects; the processing optimizations using TriplexPro Air Plasma Spray Low Pressure Plasma Spray (LPPS), Plasma Spray Physical Vapor Deposition and demonstration of EBC-CMC systems. This presentation also highlights the EBC-CMC system temperature capability and durability improvements under the NASA development programs, as demonstrated in the simulated engine high heat flux, combustion environments, in conjunction with high heat flux, mechanical creep and fatigue loading testing conditions.

Role of the polymer phase in the mechanics of nacre-like composites

Science.gov (United States)

Niebel, Tobias P.; Bouville, Florian; Kokkinis, Dimitri; Studart, André R.

2016-11-01

Although strength and toughness are often mutually exclusive properties in man-made structural materials, nature is full of examples of composite materials that combine these properties in a remarkable way through sophisticated multiscale architectures. Understanding the contributions of the different constituents to the energy dissipating toughening mechanisms active in these natural materials is crucial for the development of strong artificial composites with a high resistance to fracture. Here, we systematically study the influence of the polymer properties on the mechanics of nacre-like composites containing an intermediate fraction of mineral phase (57 vol%). To this end, we infiltrate ceramic scaffolds prepared by magnetically assisted slip casting (MASC) with monomers that are subsequently cured to yield three drastically different polymers: (i) poly(lauryl methacrylate) (PLMA), a soft and weak elastomer; (ii) poly(methyl methacrylate) (PMMA), a strong, stiff and brittle thermoplastic; and (iii) polyether urethane diacrylate-co-poly(2-hydroxyethyl methacrylate) (PUA-PHEMA), a tough polymer of intermediate strength and stiffness. By combining our experimental data with finite element modeling, we find that stiffer polymers can increase the strength of the composite by reducing stress concentrations in the inorganic scaffold. Moreover, infiltrating the scaffolds with tough polymers leads to composites with high crack initiation toughness KIC. An organic phase with a minimum strength and toughness is also required to fully activate the mechanisms programmed within the ceramic structure for a rising R-curve behavior. Our results indicate that a high modulus of toughness is a key parameter for the selection of polymers leading to strong and tough bioinspired nacre-like composites.

Assertion checking environment (ACE) for formal verification of C programs

International Nuclear Information System (INIS)

Sharma, Babita; Dhodapkar, S.D.; Ramesh, S.

2003-01-01

In this paper we describe an Assertion Checking Environment (ACE) for compositional verification of programs, which are written in an industrially sponsored safe subset of C programming language called MISRA C [Guidelines for the Use of the C Language in Vehicle Based Software, 1998]. The theory is based on Hoare logic [Commun. ACM 12 (1969) 576] and the C programs are verified using static assertion checking technique. First the functional specifications of the program, captured in the form of pre- and post-conditions for each C function, are derived from the specifications. These pre- and post-conditions are then introduced as assertions (also called annotations or formal comments) in the program code. The assertions are then proved formally using ACE and theorem proving tool called Stanford Temporal Prover [The Stanford Temporal Prover User's Manual, 1998]. ACE has been developed by us and consists mainly of a translator c2spl, a GUI and some utility programs. The technique and tools developed are targeted towards verification of real-time embedded software

Gender Diversity in Anesthesiology Programs: The Role of Current Residents and Department Leadership in the 2014 Match Results.

Science.gov (United States)

Kranner, Paul W; Mussehl, Denise A; Hess, Aaron S

2016-01-01

Nearly half of graduates of American medical colleges are women, yet the percentage of women entering accredited anesthesiology programs remains less than 40%. There are obviously many factors that influence the choice of a residency training program, from geography to reputation to the atmosphere, composition and camaraderie of the department. We examined whether a greater number of current female residents, a female Chair, or a female Program Director were associated with a program matching a greater number of female candidates in the 2014 NRMP Match. An electronic questionnaire was sent to all 132 ACGME-accredited anesthesiology programs immediately following the 2014 Match seeking information on the gender mix of their current residents, the gender of the Chair and Program Director, and the gender composition of their newly-matched candidates. The percentage of current female residents was significantly associated with the percentage of incoming female residents (p = 0.013). There was no association between the percentage of new female residents obtained in the Match and the presence of a female Chair or Program Director. The results of the 2013 NRMP anesthesiology match indicate that programs with a higher proportion of female residents were able to sustain that diversity and successfully match a higher percentage of female candidates. No correlation was seen with Chair and Program Director gender, suggesting further work is needed to define the influence of female role models on female applicants' choice of anesthesiology residency programs.

Geometric Semantic Genetic Programming Algorithm and Slump Prediction

OpenAIRE

Xu, Juncai; Shen, Zhenzhong; Ren, Qingwen; Xie, Xin; Yang, Zhengyu

2017-01-01

Research on the performance of recycled concrete as building material in the current world is an important subject. Given the complex composition of recycled concrete, conventional methods for forecasting slump scarcely obtain satisfactory results. Based on theory of nonlinear prediction method, we propose a recycled concrete slump prediction model based on geometric semantic genetic programming (GSGP) and combined it with recycled concrete features. Tests show that the model can accurately p...

Yield strengths of tungsten-base composites determined from bend tests

International Nuclear Information System (INIS)

Zukas, E.G.; Eash, D.T.

1976-08-01

The variation in yield strength with either strain rate or temperature was determined for a number of tungsten-base composites by use of the simple three-point bend test. The yield strengths were comparable with those obtained in standard tensile tests. Additional studies on 1019 steel, either in the as-rolled or annealed condition, gave results in agreement with handbook values, as did two aluminum alloys. These results demonstrate that the bend test deserves wider acceptance in materials testing programs

Body composition of italian female hockey players

Directory of Open Access Journals (Sweden)

P Pavan

2009-07-01

Full Text Available Objective: In this work the anthropometric features and the body composition of Italian hockey players, members of the Female National team, were analysed. The purpose of the research was to verify if morphological features could influence the performance of different positional groups. Materials and Methods: Each player was measured for her total and sitting height, weight, 9 skinfolds thickness and bioelectrical impedance analysis. Different equations were used to calculate the Fat% from skinfolds thickness. Results: Average height is not a crucial advantage for this sport. On the contrary the proportion trunk-limb seems to play an important role for the performance of the midfield players. Percentage of body fat of the hockey players was lower than the Fat% of the non-athletes women of the same age. Significant differences were found between Fat% determined by skinfolds thickness and Fat% obtained by bioelectrical impedance analysis. Conclusions: The results of this study indicate that there are significant differences in anthropometric features and in body composition between positional groups, stressing the importance of a specific training program. Keywords: field hockey, bioelectrical impedance, skinfolds thickness, anthropometry.