WorldWideScience

Sample records for commercial abrasion resistant

  1. Electrical resistivity measurements to predict abrasion resistance of ...

    Indian Academy of Sciences (India)

    WINTEC

    Abstract. The prediction of Los Angeles (LA) abrasion loss from some indirect tests is useful for practical applications. For this purpose, LA abrasion, electrical resistivity, density and porosity tests were carried out on 27 different rock types. LA abrasion loss values were correlated with electrical resistivity and a good corre-.

  2. Electrical resistivity measurements to predict abrasion resistance of ...

    Indian Academy of Sciences (India)

    The prediction of Los Angeles (LA) abrasion loss from some indirect tests is useful for practical applications. For this purpose, LA abrasion, electrical resistivity, density and porosity tests were carried out on 27 different rock types. LA abrasion loss values were correlated with electrical resistivity and a good correlation ...

  3. ABRASION RESISTANCE ESTIMATION OF HIGH STRENGTH CONCRETE

    Directory of Open Access Journals (Sweden)

    Şemsi YAZICI

    2007-01-01

    Full Text Available This study gives the results of a laboratory investigation undertaken to determine the relationship between mechanical properties (compressive and flexural strengths and abrasion resistance of 65-85 MPa high strength concretes incorporating silica fume, fly ash and silica fume-fly ash mixtures as supplementary cementing materials. A series of six different concrete mixtures including a control high strength concrete mixture (C1, and five high strength concrete mixtures (C2, C3, C4, C5, C6 incorporating supplementary cementing materials, were manufactured. The compressive strength, flexural strength, and abrasion resistance were determined for each mixture at 28-days. Mathematical expressions were suggested to estimate the abrasion resistance of concrete regarding their compressive strength and flexural strength.

  4. Homemade abrasion tester and its application for abrasion resistance testing of crease points on down fabrics

    Directory of Open Access Journals (Sweden)

    Yidie GUAN

    2017-02-01

    Full Text Available In order to explore a new method for testing the fabric abrasion resistance, a homemade abrasion tester is designed and manufactured. The principle, structure and test method of the homemade abrasion tester are introduced. The crease points on fabrics are rubbed using the abrasion tester under certain air pressure and the abrasion of fabrics is reflected on real time through the change of gas flow. The change of gas flow is converted into equivalent aperture by Bernoulli equation and the equivalent aperture is used to evaluate the abrasion resistance of the crease point on fabric. Three measuring parameters of friction velocity, gas pressure and fabric thickness influencing on the abrasion resistance of crease point on down fabrics are tested by orthogonal experiment. The influence of the three elements on the abrasion resistance is analyzed. The results show that the homemade abrasion tester can represent the abrasion resistance of crease point under certain conditions. The gas pressure and fabric thickness have significant influence on the abrasion resistance, but the influence of friction velocity is not significant. Above all, the gas pressure has the most high influence. The research result prevides reference for improving the abrasion resistance of crease points on down fabrics.

  5. Usage of abrasion-resistant materials in agriculture

    Directory of Open Access Journals (Sweden)

    J Votava

    2014-06-01

    Full Text Available Agricultural soil-processing machines are subject to an extensive abrasive wear. This paper analyses technical materials and their fitness to exchangeable parts of plough bottoms, such as edge-tools and whole plough cutting edges. There were tested abrasion-resistant steels with different microstructures: austenite, martensite-bainite, and carbide. Steel with the pearlite-ferrite structure was used as an etalon. Abrasion resistance tests were processed in compliance with the norm CSN 01 5084, which is a test of abrasion wear on abrasive cloth.

  6. The Abrasive Wear Resistance of Chromium Cast Iron

    Directory of Open Access Journals (Sweden)

    Kopyciński D.

    2014-03-01

    Full Text Available The resistance of cast iron to abrasive wear depends on the metal abrasive hardness ratio. For example, hardness of the structural constituents of the cast iron metal matrix is lower than the hardness of ordinary silica sand. Also cementite, the basic component of unalloyed white cast iron, has hardness lower than the hardness of silica. Some resistance to the abrasive effect of the aforementioned silica sand can provide the chromium white cast iron containing in its structure a large amount of (Cr, Fe7C3 carbides characterised by hardness higher than the hardness of the silica sand in question. In the present study, it has been anticipated that the white cast iron structure will be changed by changing the type of metal matrix and the type of carbides present in this matrix, which will greatly expand the application area of castings under the harsh operating conditions of abrasive wear. Moreover, the study compares the results of abrasive wear resistance tests performed on the examined types of cast iron. Tests of abrasive wear resistance were carried out on a Miller machine. Samples of standard dimensions were exposed to abrasion in a double to-and-fro movement, sliding against the bottom of a trough filled with an aqueous abrasive mixture containing SiC + distilled water. The obtained results of changes in the sample weight were approximated with a power curve and shown further in the study.

  7. Evaluation of abrasion resistance of pipe and pipe lining materials.

    Science.gov (United States)

    2007-09-01

    This project summarizes an evaluation of pipe material resistance to abrasion over a 5-year period (2001-2006) at a site known to be abrasive. : The key focus of the project was to gather more information to compare against existing guidance to desig...

  8. The abrasive effect of commercial whitening toothpastes on eroded enamel.

    Science.gov (United States)

    Mosquim, Victor; Martines Souza, Beatriz; Foratori Junior, Gerson Aparecido; Wang, Linda; Magalhães, Ana Carolina

    2017-06-01

    To evaluate the in vitro abrasive effect of commercial whitening toothpastes on eroded bovine enamel samples in respect to erosive tooth wear. 72 bovine crowns were embedded, polished and subjected to the baseline profile analysis. The samples were then protected in 2/3 of the enamel surface and were randomly assigned to six groups (n= 12/group): G1: Oral-B 3D White, G2: Close-up Diamond Attraction Power White, G3: Sorriso Xtreme White 4D, G4: Colgate Luminous White, G5: Crest (conventional toothpaste), G6:erosion only (control). All samples were submitted to an erosive pH cycling (4 x 90 seconds in 0.1% citric acid, pH 2.5, per day) and abrasive challenges (2 x 15 seconds, per day) for 7 days. After the first and the last daily cycles, the samples were subjected to abrasive challenges, using a toothbrushing machine, soft toothbrushes and slurry of the tested toothpastes (1.5 N). Between the challenges, the samples were immersed in artificial saliva. The final profile was obtained and overlaid to the baseline profile for the calculation of the erosive tooth wear (μm). The data were subjected to Kruskal-Wallis/Dunn tests (Ptoothpastes, especially those containing pyrophosphate associated with hydrated silica, enhanced enamel erosive wear.

  9. Resistance of dentin coating materials against abrasion by toothbrush.

    Science.gov (United States)

    Gando, Iori; Ariyoshi, Meu; Ikeda, Masaomi; Sadr, Alireza; Nikaido, Toru; Tagami, Junji

    2013-01-01

    Thin-film coating of root dentin surface by all-in-one adhesives has been shown to be an effective option to prevent root surface caries. The purpose of this study was to investigate the wear resistance against toothbrush abrasion of two all-in-one coating materials; Shield Force (SF) and Hybrid Coat (HC). Bovine dentin surfaces were covered with one of the coating materials; SF or HC. After storage in water for 24 h, the testing surface was subjected to the toothbrush abrasion test up to 50,000 cycles either in water or toothpaste slurry. The remaining thickness of the coating material was measured using SEM. Toothpaste slurry significantly increased rate of tooth brush abrasion of the coating materials. While SF and HC wore at a similar pace under toothbrush abrasion, SF had a thicker coat and could protect dentin longer, up to 50,000 cycles.

  10. Micro-Abrasion Wear Resistance of Borided 316L Stainless Steel and AISI 1018 Steel

    Science.gov (United States)

    Reséndiz-Calderon, C. D.; Rodríguez-Castro, G. A.; Meneses-Amador, A.; Campos-Silva, I. E.; Andraca-Adame, J.; Palomar-Pardavé, M. E.; Gallardo-Hernández, E. A.

    2017-11-01

    The 316L stainless steel has high corrosion resistance but low tribological performance. In different industrial sectors (biomedical, chemical, petrochemical, and nuclear engineering), improvement upon wear resistance of 316L stainless steel components using accessible and inexpensive methods is critical. The AISI 1018 steel is widely used in industry, but its tribological performance is not the best among steels. Therefore, in this study the behavior of the borided 316L stainless steel and 1018 steel is evaluated under micro-abrasion wear. The boriding was carried out at 1223 K over 6 h of exposure time, resulting in a biphase layer composed of FeB/Fe2B phases. In order to evaluate Fe2B phase with no influence from FeB phase, AISI 1018 steel samples were borided at 1273 K for over 20 min and then diffusion annealed at 1273 K over 2 h to obtain a Fe2B mono-phase layer. Micro-abrasion wear resistance was evaluated by a commercial micro-abrasion testing rig using a mix of F-1200 SiC particles with deionized water as abrasive slurry. The obtained wear rates for FeB and Fe2B phases and for the 316L stainless steel were compared. Wear resistance of 316L stainless steel increases after boriding. The wear mechanisms for both phases and for the stainless steel were identified. Also, transient conditions for rolling and grooving abrasion were determined for the FeB and Fe2B phases.

  11. Micro-Abrasion Wear Resistance of Borided 316L Stainless Steel and AISI 1018 Steel

    Science.gov (United States)

    Reséndiz-Calderon, C. D.; Rodríguez-Castro, G. A.; Meneses-Amador, A.; Campos-Silva, I. E.; Andraca-Adame, J.; Palomar-Pardavé, M. E.; Gallardo-Hernández, E. A.

    2017-10-01

    The 316L stainless steel has high corrosion resistance but low tribological performance. In different industrial sectors (biomedical, chemical, petrochemical, and nuclear engineering), improvement upon wear resistance of 316L stainless steel components using accessible and inexpensive methods is critical. The AISI 1018 steel is widely used in industry, but its tribological performance is not the best among steels. Therefore, in this study the behavior of the borided 316L stainless steel and 1018 steel is evaluated under micro-abrasion wear. The boriding was carried out at 1223 K over 6 h of exposure time, resulting in a biphase layer composed of FeB/Fe2B phases. In order to evaluate Fe2B phase with no influence from FeB phase, AISI 1018 steel samples were borided at 1273 K for over 20 min and then diffusion annealed at 1273 K over 2 h to obtain a Fe2B mono-phase layer. Micro-abrasion wear resistance was evaluated by a commercial micro-abrasion testing rig using a mix of F-1200 SiC particles with deionized water as abrasive slurry. The obtained wear rates for FeB and Fe2B phases and for the 316L stainless steel were compared. Wear resistance of 316L stainless steel increases after boriding. The wear mechanisms for both phases and for the stainless steel were identified. Also, transient conditions for rolling and grooving abrasion were determined for the FeB and Fe2B phases.

  12. Gouging abrasion resistance of materials for oil sands service

    Energy Technology Data Exchange (ETDEWEB)

    Llewellyn, R.J. [National Research Council of Canada, Vancouver, BC (Canada); Tolfree, D.J.; Hall, R.A. [British Columbia Univ., Vancouver, BC (Canada). Dept. of Mining and Mineral Process Engineering; Liang, P. [British Columbia Univ., Vancouver, BC (Canada). Dept. of Metals and Materials Engineering

    2004-07-01

    Hydraulic ore transportation in the oil sands industry has brought about a need for effective and reliable crusher and classifying systems to pulverize, screen and handle mined frozen oil sands lumps and large solids before they get slurried and pipelined to bitumen extraction plants. Improved product development, assessment methods for materials for oil sands applications have generally focused on low and high stress abrasion and slurry erosion resistance because these wear mechanisms are considered to predominate in oil sands mining, transportation and bitumen recovery. With the increased use of crusher and slurry handling systems, materials of construction are required to have good toughness and gouging abrasion properties to withstand impact and ploughing forces. Tests of gouging abrasion were conducted using a modified ASTM G81 procedure on a range of materials associated with oil sands processing. The objective was to assess material property requirements for mitigating these conditions. The wear losses that occurred for reference wear plates were compared to feed rock that was pulverized in a laboratory jaw crusher. The classes of evaluated materials were abrasion resistant (AR) steel plates, austenitic manganese steel castings, chromium and chromium molybdenum white irons (as plain castings and in laminated forms), and chromium carbide and tungsten carbide overlaid wear plates. 8 refs., 1 tab., 11 figs.

  13. Standard Test Method for Abrasive Wear Resistance of Cemented

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2005-01-01

    1.1 This test method covers the determination of abrasive wear resistance of cemented carbides. 1.2 The values stated in inch-pound units are to be regarded as the standard. The SI equivalents of inch-pound units are in parentheses and may be approximate. 1.3 This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  14. Heat sealable, flame and abrasion resistant coated fabric

    Science.gov (United States)

    Tschirch, R. P.; Sidman, K. R. (Inventor)

    1983-01-01

    Flame retardant, abrasion resistant elastomeric compositions are disclosed which are comprised of thermoplastic polyurethane polymer and flame retarding amounts of a filler selected from decabromodiphenyloxide and antimony oxide in a 3:1 weight ratio, and decabromodiphenyloxide, antimony oxide, and ammonium polyphosphate in a 3:1:3 weight ratio respectively. Heat sealable coated fabrics employing such elastomeric compositions as coating film are produced by dissolving the elastomeric composition to form a solution, casting the solution onto a release paper and drying it to form an elastomeric film. The film is then bonded to a woven, knitted, or felted fabric.

  15. To Evaluate Effect of Airborne Particle Abrasion using Different Abrasives Particles and Compare Two Commercial Available Zirconia on Flexural Strength on Heat Treatment.

    Science.gov (United States)

    Prasad, Hari A; Pasha, Naveed; Hilal, Mohammed; Amarnath, G S; Kundapur, Vinaya; Anand, M; Singh, Sumeet

    2017-06-01

    The popularity of ceramic restorations can be attributed to its life-like appearance, durability and biocompatibility and therefore ceramic restorations have been widely used for anterior and posterior teeth. Ceramic restorations have esthetic and biocompatible advantages but low fracture resistance. Since it has high flexural strength and fracture resistance, yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) is the dental material most commonly used for the core of ceramic crowns and fixed dental prosthesis. In spite of improved mechanical properties, acceptable marginal adaptation and biocompatibility the whitish opacity of zirconia is an obvious esthetic disadvantage. The zirconia framework is often veneered with conventional feldspathic porcelain to achieve a natural appearance. However it is difficult to achieve sufficient bond strength between zirconia and the veneering material. Achieving sufficient bond strength between the veneering ceramic and the zirconia core is a major challenge in the long term clinical success of veneered zirconia restorations. The main objective of this study is to evaluate the effect of different surface treatments on the fracture strength of the two commercially available Zirconia namely Ceramill and ZR-White (AMANNGIRRBACH and UPCERA) respectively. Two commercially available pre-sinteredyttrium stabilized Zirconia blanks (ZR-White and Ceramill) from AMANNGIRRBACH and UPCERA respectively are used to produce the disc shaped specimens of size (15.2 ± 0.03 mm in diameter and 1.2 ± 0.03 mm thick) from each Zirconia blank. All disc shaped specimens are heated at 1200°C in a furnace for 2 hours to form homogenous tetragonal ZrO2. The dimensions of the specimens are measured with a digital caliper (aerospace). The thickness and diameter of each specimen are calculated as the means of 3 measurements made at random sites. 80 discs from each Zirconia blank are divided into ten groups of 8 specimens each. Heat treatment after

  16. Report D : self-consolidating concrete (SCC) for infrastructure elements - creep, shrinkage and abrasion resistance.

    Science.gov (United States)

    2012-08-01

    Concrete specimens were fabricated for shrinkage, creep, and abrasion resistance : testing. Variations of self-consolidating concrete (SCC) and conventional concrete were : all tested. The results were compared to previous similar testing programs an...

  17. HYDRO-ABRASIVE RESISTANCE AND MECHANICAL PROPERTIES OF CONCRETE WITH ADDED FLY ASH

    OpenAIRE

    Ristić, Nenad; Grdić, Zoran; Topličić-Ćurčić, Gordana

    2015-01-01

    The durability of hydraulic engineering structures mostly depends on the resistance of their concrete surfaces to mechanical abrasion. In this paper, we study the hydro-abrasive resistance and mechanical properties of concrete in which cement is partially replaced with fly ash in various proportions. To evaluate these concretes, we measured their compressive strength, flexural strength, static modulus of elasticity, ultrasound velocity through concrete, and sclerometer rebound. The hydro-abra...

  18. Measurement of the Resistance of Treated Metal Foils to Scrubbing Abrasion Using a Modified Reciprocating Wear Test

    Energy Technology Data Exchange (ETDEWEB)

    Qu, Jun [ORNL; Blau, Peter Julian [ORNL; Sikka, Vinod K [ORNL

    2007-01-01

    A reciprocating wear test method has been developed to evaluate the resistance of metal foils to scrubbing abrasion. Development included the definition of a quantitative measure of the scrubbing resistance. In order to test the ability of the new method to differentiate between surface treatments, four versions of Type 316 stainless steel foils were tested: annealed (A-NT), cold-worked (C-NT), annealed plus a case-hardened (A-T), and cold-worked plus case-hardened (C-T). Measurements were made of their scrubbing resistance using commercial kitchen scrub pads as the counterface material. Results showed that the case-hardening process significantly increased the scrubbing resistance both under dry conditions and with cleaning solutions to lubricate the contact. While this linearly-reciprocating method does not simulate the circular, overlapping motion commonly occurring in service, results indicated that the new test method could sufficiently discriminate levels of two-body abrasion behavior, and therefore can be useful for studying the effects of surface treatments on abrasion resistance.

  19. To Evaluate Effect of Airborne Particle Abrasion using Different Abrasives Particles and Compare Two Commercial Available Zirconia on Flexural Strength on Heat Treatment

    Science.gov (United States)

    Prasad, Hari A.; Pasha, Naveed; Hilal, Mohammed; Amarnath, G. S.; Kundapur, Vinaya; Anand, M; Singh, Sumeet

    2017-01-01

    Background and objective: The popularity of ceramic restorations can be attributed to its life-like appearance, durability and biocompatibility and therefore ceramic restorations have been widely used for anterior and posterior teeth. Ceramic restorations have esthetic and biocompatible advantages but low fracture resistance. Since it has high flexural strength and fracture resistance, yttria-stabilized tetragonal zirconia polycrystal (Y-TZP) is the dental material most commonly used for the core of ceramic crowns and fixed dental prosthesis. In spite of improved mechanical properties, acceptable marginal adaptation and biocompatibility the whitish opacity of zirconia is an obvious esthetic disadvantage. The zirconia framework is often veneered with conventional feldspathic porcelain to achieve a natural appearance. However it is difficult to achieve sufficient bond strength between zirconia and the veneering material. Achieving sufficient bond strength between the veneering ceramic and the zirconia core is a major challenge in the long term clinical success of veneered zirconia restorations. The main objective of this study is to evaluate the effect of different surface treatments on the fracture strength of the two commercially available Zirconia namely Ceramill and ZR-White (AMANNGIRRBACH and UPCERA) respectively. Method: Two commercially available pre-sinteredyttrium stabilized Zirconia blanks (ZR-White and Ceramill) from AMANNGIRRBACH and UPCERA respectively are used to produce the disc shaped specimens of size (15.2 ± 0.03 mm in diameter and 1.2 ± 0.03 mm thick) from each Zirconia blank. All disc shaped specimens are heated at 1200°C in a furnace for 2 hours to form homogenous tetragonal ZrO2. The dimensions of the specimens are measured with a digital caliper (aerospace). The thickness and diameter of each specimen are calculated as the means of 3 measurements made at random sites. 80 discs from each Zirconia blank are divided into ten groups of 8

  20. Abrasion Resistance of as-Cast High-Chromium Cast Iron

    Directory of Open Access Journals (Sweden)

    Pokusová Marcela

    2014-12-01

    Full Text Available High chromium cast irons are widely used as abrasion resistant materials. Their properties and wear resistance depend on carbides and on the nature of the matrix supporting these carbides. The paper presents test results of irons which contain (in wt.% 18-22 Cr and 2-5 C, and is alloyed by 1.7 Mo + 5 Ni + 2 Mn to improve the toughness. Tests showed as-cast irons with mostly austenitic matrix achieved hardness 36-53 HRC but their relative abrasion-resistance was higher than the tool steel STN 19436 heat treated on hardness 60 HRC.

  1. Wear and abrasion resistance selection maps of biological materials.

    Science.gov (United States)

    Amini, Shahrouz; Miserez, Ali

    2013-08-01

    The mechanical design of biological materials has generated widespread interest in recent years, providing many insights into their intriguing structure-property relationships. A critical characteristic of load-bearing materials, which is central to the survival of many species, is their wear and abrasion tolerance. In order to be fully functional, protective armors, dentitious structures and dynamic appendages must be able to tolerate repetitive contact loads without significant loss of materials or internal damage. However, very little is known about this tribological performance. Using a contact mechanics framework, we have constructed materials selection charts that provide general predictions about the wear performance of biological materials as a function of their fundamental mechanical properties. One key assumption in constructing these selection charts is that abrasion tolerance is governed by the first irreversible damage at the contact point. The maps were generated using comprehensive data from the literature and encompass a wide range of materials, from heavily mineralized to fully organic materials. Our analysis shows that the tolerance of biological materials against abrasion depends on contact geometry, which is ultimately correlated to environmental and selective pressures. Comparisons with experimental data from nanoindentation experiments are also drawn in order to verify our predictions. With the increasing amount of data available for biological materials also comes the challenge of selecting relevant model systems for bioinspired materials engineering. We suggest that these maps will be able to guide this selection by providing an overview of biological materials that are predicted to exhibit the best abrasion tolerance, which is of fundamental interest for a wide range of applications, for instance in restorative implants and protective devices. Copyright © 2013 Acta Materialia Inc. Published by Elsevier Ltd. All rights reserved.

  2. Influence of Heat Treatment on Abrasive Wear Resistance of Silumin Matrix Composite Castings

    Directory of Open Access Journals (Sweden)

    Gawdzińska K.

    2016-03-01

    Full Text Available The authors attempted at examining the effect of heat treatment on abrasive wear resistance of metal composite castings. Metal matrix composites were made by infiltrating preforms created from unordered short fibers (graphite or silumin with liquid aluminium alloy AlSi12(b. Thus prepared composites were subject to solution heat treatment at a temperature of 520°C for four hours, then aging at a temperature of 220°C for four hours. Abrasion resistance of the material was tested before and after thermal treatment.

  3. The Effect of Microstructure on the Abrasion Resistance of Low Alloyed Steels

    NARCIS (Netherlands)

    Xu, X.

    2016-01-01

    The thesis attempts to develop advanced high abrasion resistant steels with low hardness in combination with good toughness, processability and low alloying additions. For this purpose, a novel multi-pass dual-indenter (MPDI) scratch test approach has been developed to approach the real continuous

  4. Effect of commercial fluoride dentifrices against hydrochloric acid in an erosion-abrasion model.

    Science.gov (United States)

    Passos, Vanara Florêncio; de Vasconcellos, Andréa Araújo; Pequeno, José Heriberto Pinheiro; Rodrigues, Lidiany Karla Azevedo; Santiago, Sérgio Lima

    2015-01-01

    This study assessed the effect of three commercial dentifrices with different fluoride-containing compounds in controlling the progression of dentin loss using an in vitro erosion-abrasion model. Dentin specimens were randomized into four groups (n = 10): control (no F), Elmex (1,400 ppm AmF), Meridol (1,400 ppm AmF/SnF2), and Crest Pro-Health (1,100 ppm SnF2). The dentin specimens were submitted to cycles of demineralization (HCl 0.01 M for 60 s), remineralization (artificial saliva for 60 min), and immersion in 1:3 w/w of dentifrice/artificial saliva, followed by toothbrushing (150 brushing strokes). The cycle was repeated three times daily for 5 days. Surface loss was quantified by stylus profilometry. Data were submitted to one-way ANOVA and Tukey's tests (p acid damage. However, the beneficial effect of different fluorides present in commercial dentifrices is questionable. Thus, a determination of an effective fluoride dentifrice may be beneficial in the reduction of the erosive process in patients with gastric disorders.

  5. Resistance to Abrasive Wear and Volume Fraction of Carbides in Cast High-manganese Austenitic Steel with Composite Structure

    Directory of Open Access Journals (Sweden)

    Tęcza G.

    2015-12-01

    Full Text Available Cast Hadfield steel is characterised by high abrasion resistance, provided, however, that it is exposed to the effect of dynamic loads. During abrasion without loading, e.g. under the impact of loose sand jet, its wear resistance drops very drastically. To increase the abrasion resistance of this alloy under the conditions where no pressure is acting, primary vanadium carbides are formed in the metallurgical process, to obtain a composite structure after the melt solidification. The primary, very hard, carbides uniformly distributed in the austenitic matrix are reported to double the wear resistance of samples subjected to the effect of a silicon carbide-water mixture.

  6. Evaluation of Surface Microhardness and Abrasion Resistance of Two Dental Glass Ionomer Cement Materials after Radiant Heat Treatment

    Directory of Open Access Journals (Sweden)

    Dimitrios Dionysopoulos

    2017-01-01

    Full Text Available The aim of this study was to evaluate the effect of a radiant heat treatment using a dental LED unit on the surface microhardness and abrasion resistance after toothbrushing simulation of two conventional GIC materials. Two conventional GIC materials were studied in this investigation: Ketac Fil Plus Aplicap and IonoStar Molar. Twenty disk-shaped specimens (n=10 were prepared of each GIC (7 mm × 2 mm using cylindrical Teflon molds. Group 1 specimens were left in the mold to set without any treatment, while in Group 2 after placement in the mold the specimens were irradiated for 60 sec at the top surface using a LED light-curing unit. Toothbrushing simulation was carried out using a commercial electric toothbrush which was fixed in a constructed device that allowed the heads of the brushes to be aligned parallel to the surface of the specimens and to control the pressure, with the following parameters: load of the toothbrush standardized at 250 g, medium hardness toothbrush head, and rotation sense changing every 30 sec. The toothbrush abrasion test mechanism, based on a 1.25-Hz frequency for 10,000 cycles, was equivalent to 800 days (~2 years of brushing. Surface hardness, surface roughness, and surface loss after abrasive procedure were evaluated using Vickers method and Vertical Scanning Interferometry. Data were statistically analyzed using one-way ANOVA and Tukey’s post hoc test (a=0.05. The radiant heat treatment increased the surface microhardness and decreased surface roughness and surface loss after abrasive procedures of both the tested GIC materials but to different extent. Between the tested GIC materials there were significant differences in their tested properties (p<0.05.

  7. Abrasive Wear Resistance of the Iron- and WC-based Hardfaced Coatings Evaluated with Scratch Test Method

    Directory of Open Access Journals (Sweden)

    A. Vencl

    2013-06-01

    Full Text Available Abrasive wear is one of the most common types of wear, which makesabrasive wear resistance very important in many industries. Thehard facing is considered as useful and economical way to improve theperformance of components submitted to severe abrasive wear conditions, with wide range of applicable filler materials. The abrasive wear resistance of the three different hardfaced coatings (two iron‐based and one WC‐based, which were intended to be used for reparation of the impact plates of the ventilation mill, was investigated and compared. Abrasive wear tests were carried‐out by using the scratch tester under the dry conditions. Three normal loads of 10, 50 and 100 N and the constant sliding speed of 4 mm/s were used. Scratch test was chosen as a relatively easy and quick test method. Wear mechanism analysis showed significant influence of the hardfaced coatings structure, which, along with hardness, has determined coatings abrasive wear resistance.

  8. Predicting the Abrasion Resistance of Tool Steels by Means of Neurofuzzy Model

    Directory of Open Access Journals (Sweden)

    Dragutin Lisjak

    2013-07-01

    Full Text Available This work considers use neurofuzzy set theory for estimate abrasion wear resistance of steels based on chemical composition, heat treatment (austenitising temperature, quenchant and tempering temperature, hardness after hardening and different tempering temperature and volume loss of materials according to ASTM G 65-94. Testing of volume loss for the following group of materials as fuzzy data set was taken: carbon tool steels, cold work tool steels, hot work tools steels, high-speed steels. Modelled adaptive neuro fuzzy inference system (ANFIS is compared to statistical model of multivariable non-linear regression (MNLR. From the results it could be concluded that it is possible well estimate abrasion wear resistance for steel whose volume loss is unknown and thus eliminate unnecessary testing.

  9. Abrasion-Resistant Aluminized-Coated Aramid Fabrics for Manufacture of Firefighters’ Protective Clothing

    Science.gov (United States)

    1985-05-01

    and radiacion are also produced at the cathode surface and may profoundly influence the quality of the substrate coating. These include secondary...14,265-378 (1979). Assink, R.A. Abrasion resistant polymer reflectors for solar applications. Solar Energy Mater vol. 3:263-75, (1980). Audet, N.F. Visor... solar reflectors. Solar Energy Mater vol. 3: No.1-2,277-83,(1981). *Gubareff, G.G., J.E. Janssen, and R.H. Torborg. Thermal radiation properties survey

  10. Heat sealable, flame and abrasion resistant coated fabric. [clothing and containers for space exploration

    Science.gov (United States)

    Tschirch, R. P.; Sidman, K. R. (Inventor)

    1981-01-01

    Flame retardant, abrasion resistant elastomeric compositions are comprised of thermoplastic polyurethane polymer and flame retarding amounts of a filler selected from decabromodiphenyloxide and antimony oxide in a 3:1 weight ratio, and decabromodiphenyloxide, antimony oxide, and ammonium polyphosphate in a 3:1:3 weight ratio respectively. Coated fabrics employing such elastomeric compositions as coating film are flexible, lightweight, and air impermeable and can be made using heat or dielectric sealing procedures.

  11. Abrasive Wear Resistance of Overlay Composite Alloy with Addition of Carbide Powders

    OpenAIRE

    Tadao, ARAKI; Minoru, NISHIDA; Akio, HIROSE; Kouji, YANO; HIroshi, FUJITA; Faculty of Eng., Ehime University; Faculty of Eng., Ehime University; Faculty of Eng., Osaka University; Kawasaki Steel Co., Ltd.; Tokuden Co., Ltd.

    1993-01-01

    The overall objective of this project is to provide data showing how carbide powder in addition to base alloy powder can be used effectively to increase hardness of overlay alloy and resistance to abrasive wear. An experimental study was performed to examine combinations of base alloy powders and reinforcing powders. The base alloy powders considered were stainless steel, Ni-base alloy, Co-base alloy and high speed steel powder, while reinforcing powders considered were metal-carbide and cera...

  12. Protective, Abrasion-Resistant Coatings With Tailorable Properties

    Science.gov (United States)

    1996-01-01

    Because of their light weight and impact resistance, transparent plastic structures are becoming increasingly desirable for use not only on aircraft but also in terrestrial applications such as automotive windshields and ophthalmic lenses. However, plastics are typically soft and scratch readily, reducing their transparency with use. At the NASA Lewis Research Center, reactively deposited aluminum oxide coatings as thin as 12,000 angstroms have been demonstrated to provide improved resistance to most scratches encountered during normal use. The properties of the coating can be adjusted to tailor the surface to meet other needs, such as water shedding. These adjustments can be made during the deposition process so that multiple manufacturing steps are eliminated.

  13. Selected Plastics Wear Resistance to Bonded Abrasive Particles Compared to Some Ferrous Materials

    Directory of Open Access Journals (Sweden)

    Milan Brožek

    2015-01-01

    Full Text Available Plastics are macromolecular materials without we cannot imagine any branch of human activity with. Plastics have unique properties, often very different from metals. At the choice of the concrete plastic for the concrete application it is necessary to evaluate its mechanical, physical, chemical and technological properties. In last years producers offer also plastics for production of parts exposed to different types of wear. In the contribution the results of wear resistance studying of 10 types of plastics (PTFE, PVC, POM-C, PC, PETP, PEEK, PA66, PP, PA6E and PE-UHMW of one producer are published and compared with test results of four different Fe alloys (grey iron, structural steel, cast steel wear resistant and high-speed steel. The laboratory tests were carried out using the pin-on-disk machine with abrasive cloth (according to ČSN 01 5084, when the abrasive clothes of three different grits (240, 120 and 60 were used. It corresponds to the average abrasive grain sizes of 44.5 µm, 115.5 µm and 275 µm. During the test the test sample was pressed to the abrasive cloth by the pressure of 0.1 MPa. The wear intensity was assessed by the volume, weight and length losses of tested samples. The technical-economical evaluation was the part of the carried out tests. It was univocally proved that at the intensive abrasive wear using the abrasive cloth the best results shows the High-Speed Steel HSS Poldi Radeco 19 810 according to ČSN 41 9810, although its price is relatively high. Other tested Fe alloys, namely grey iron according to ČSN 42 2415, structural steel 11 373 according to ČSN 41 1373 and wear resistant cast steel VPH 6 showed also very favourable properties at the material low price. In comparison with Fe alloys the wear of all plastics was considerably higher and the plastics were considerably more expensive.

  14. Initial Assessment of Abrasive Wear Resistance of Austempered Cast Iron with Vermicular Graphite

    Directory of Open Access Journals (Sweden)

    Soiński M. S.

    2014-10-01

    Full Text Available The work compares the abrasive wear resistance of cast iron containing vermicular graphite, measured in the as-cast state and after austempering carried out at 290°C, 340°C, or 390°C. Theexaminations were performed by means of the T-01M tribological tester using the pin-on-disc configuration. Specimens used for examinations were taken from the end tabs of the tensile specimens, these being cut out of the test walls of the double-leg keel block test castings. Examinations proved that the austempering process increases the abrasive wear resistance of vermicular cast iron by several times as compared with the as-cast material. A tendency for a slight decrease in abrasive wear with an increase in austempering temperature can be stated. The coefficient of friction took a little higher values for cast iron after thermal treatment than for the as-cast material. The work was completed with roughness examination by means of electron scanning microscopy.

  15. Examining of abrasion resistance of hybrid composites reinforced with SiC and Cgr particles

    Directory of Open Access Journals (Sweden)

    M. Łągiewka

    2008-08-01

    Full Text Available The presented work discusses the influence of the type and volume percentage of particulate reinforcement consisting of mixed silicon carbide and graphite on the abrasion wear of hybrid composites with AlMg10 matrix. Also the macro photos of frictional surfaces have been shown and the results of hardness measurements have been presented. The performed examinations have allowed for stating that the mixture of SiC and Cgr particles changes in favour the tribological properties of the matrix alloy. It has been also proved that introducing hard reinforcing particles along with soft lubricating ones allows for achieving the material exhibiting high abrasion resistance, and moreover, the graphite particles protect the abraded surface from the destructive action of silicon carbide particles. Also hardness measurements have been performed and the resulting conclusion is that the composite hardness increases with an increase in volume fraction of the reinforcing particles.

  16. The influence of aluminum and carbon on the abrasion resistance of high manganese steels

    Science.gov (United States)

    Buckholz, Samuel August

    Abrasive wear testing of lightweight, austenitic Fe-Mn-Al-C cast steel has been performed in accordance with ASTM G65 using a dry sand, rubber wheel, abrasion testing apparatus. Testing was conducted on a series of Fe-30Mn-XAl-YC-1Si-0.5Mo chemistries containing aluminum levels from 2.9 to 9.5 wt.% and carbon levels from 0.9 to 1.83 wt.%. Solution treated materials having an austenitic microstructure produced the highest wear resistance. Wear resistance decreased with higher aluminum, lower carbon, and higher hardness after age hardening. In the solution treated condition the wear rate was a strong function of the aluminum to carbon ratio and the wear rate increased with a parabolic dependence on the Al/C ratio, which ranged from 1.8 to 10.2. Examination of the surface wear scar revealed a mechanism of plowing during abrasion testing and this method of material removal is sensitive to work hardening rate. Work hardening behavior was determined from tensile tests and also decreased with increasing Al/C ratio and after aging hardening. The loss of wear resistance is related to short range ordering of Al and C in the solution treated materials and kappa-carbide precipitation in age hardened materials and both contribute to planar slip and lower work hardening rates. A high carbon tool steel (W1) and a bainitic low alloy steel (SAE 8620) were also tested for comparison. A lightweight steel containing 6.5 wt.% Al and 1.2 wt.% C has wear resistance comparable to within 5% of the bainitic SAE 8620 steel forging currently used for the Bradley Fighting Vehicle track shoe and this cast Fe-Mn-Al-C steel, at equivalent tensile properties, would be 10% lighter.

  17. Effects of Running Shoes with Abrasion Resistant Rubber Sole on the Exercise Capacity of the Human Body

    Directory of Open Access Journals (Sweden)

    Bo Wang

    2017-10-01

    Full Text Available With the development of industrialization, rubber has been gradually used in the manufacture of sports equipment for its favourable properties. This study involved the addition of C5 petroleum resin into brominated isobutylene-isoprene rubber (BIIR and butadiene rubber (BR while manufacturing the sole of running shoes. The effects of running shoes with abrasion resistant rubber sole on the exercise capacity of the human body were investigated by analysing the skid resistance and abrasion resistance of the running shoes, and conducting biomechanical study on naked feet and feet wearing the shoes. The results demonstrated that the rubber sole had favourable slip resistance property and mechanical properties such as stretching, abrasion resistance, and hardness. Compared to naked feet, the peak pressure intensity of the whole step of feet wearing the newly developed shoes, was significantly lower than that of feet wearing ordinary shoes. In the future, rubber can bring more comfortable experience because of its favourable properties.

  18. Influence of Utilization of High-Volumes of Class F Fly Ash on the Abrasion Resistance of Concrete

    Directory of Open Access Journals (Sweden)

    William PRINCE

    2007-01-01

    Full Text Available Utilization of large volumes of fly ash in various concrete applications is a becoming a more general practice in an efforts towards using large quantities of fly ash. Around the world, Class C or Class F or both as available have been used in high volumes in cement-based materials. In India, majority of fly generated is of Class F type as per ASTM C 618. Yearly fly ash generation in India is approximately 95 million tonnes. Out of which around 15-20% is utilized in cement production and cement/concrete related activities. In order to increase its percentage utilization, an investigation was carried out to use it in concrete.In this paper, abrasion resistance of high volume fly ash (HVFA concretes made with 35, 45, 55, and 65% of cement replacement was evaluated in terms of its relation with compressive strength. Comparison was made between ordinary Portland cement and fly ash concrete. Test results indicated that abrasion resistance of concrete having cement replacement up to 35 percent was comparable to the normal concrete mix with out fly ash. Beyond 35% cement replacement, fly ash concretes exhibited slightly lower resistance to abrasion relative to non-fly ash concretes. Test results further indicated that abrasion resistance of concrete is closely related with compressive strength, and had a very good correlation between abrasion resistance and compressive strength (R2 value between 0.9018 and 0.9859 depending upon age.

  19. Hydrothermal treatment for TiN as abrasion resistant dental implant coating and its fibroblast response.

    Science.gov (United States)

    Shi, Xingling; Xu, Lingli; Munar, Melvin L; Ishikawa, Kunio

    2015-04-01

    Dental implant made of pure titanium (Ti) is prone to scratch and abrasion during routine oral hygiene procedures. This results an increase in surface roughness and therefore, facilitates the adhesion of bacteria. In severe cases, this could lead to peri-implantitis. To overcome this problem, surface modification of Ti is necessary to improve its abrasion resistance. Besides, a strong implant-gingiva interface should also be guaranteed to prevent the adhesion of bacteria. In this study, titanium nitride (TiN) coating was first prepared with gas nitriding to increase surface hardness of pure the substrate. Then, the TiN was hydrothermally treated in CaCl2 solution in order to improve its soft tissue biocompatibility. The effect of hydrothermal treatment temperature on surface properties of TiN was investigated and its biocompatibility was assessed in vitro using NIH3T3 fibroblast cell. It was determined that 120°C was the critical temperature for the hydrothermal treatment condition. Treatment below 120°C could incorporate Ca into TiN surface, oxidize TiN surface partially and then improve the wettability while preserving its morphology and hardness. Fibroblast cell attachment and proliferation were improved and cell spreading was enhanced on hydrothermally treated specimens compared with untreated ones. Improved wettability, Ca incorporation and negative surface due to interstitial N were believed to be the main reasons. Hydrothermal treatment is expected to make TiN a promising dental implant coating with excellent abrasion resistance and good soft tissue affinity. Copyright © 2014 Elsevier B.V. All rights reserved.

  20. Hydrothermal treatment for TiN as abrasion resistant dental implant coating and its fibroblast response

    Energy Technology Data Exchange (ETDEWEB)

    Shi, Xingling, E-mail: shixingling1985@hotmail.com [School of Material Science and Engineering, Jiangsu University of Science and Technology, Zhenjiang 212003 (China); Department of Biomaterials, Faculty of Dental Science, Kyushu University, Fukuoka 812-8582 (Japan); Jiangsu Provincial Key Laboratory for Interventional Medical Devices, Huaiyin Institute of Technology, Huaian 223003 (China); Xu, Lingli [School of Material Science and Engineering, Jiangsu University of Science and Technology, Zhenjiang 212003 (China); Munar, Melvin L.; Ishikawa, Kunio [Department of Biomaterials, Faculty of Dental Science, Kyushu University, Fukuoka 812-8582 (Japan)

    2015-04-01

    Dental implant made of pure titanium (Ti) is prone to scratch and abrasion during routine oral hygiene procedures. This results an increase in surface roughness and therefore, facilitates the adhesion of bacteria. In severe cases, this could lead to peri-implantitis. To overcome this problem, surface modification of Ti is necessary to improve its abrasion resistance. Besides, a strong implant–gingiva interface should also be guaranteed to prevent the adhesion of bacteria. In this study, titanium nitride (TiN) coating was first prepared with gas nitriding to increase surface hardness of pure the substrate. Then, the TiN was hydrothermally treated in CaCl{sub 2} solution in order to improve its soft tissue biocompatibility. The effect of hydrothermal treatment temperature on surface properties of TiN was investigated and its biocompatibility was assessed in vitro using NIH3T3 fibroblast cell. It was determined that 120 °C was the critical temperature for the hydrothermal treatment condition. Treatment below 120 °C could incorporate Ca into TiN surface, oxidize TiN surface partially and then improve the wettability while preserving its morphology and hardness. Fibroblast cell attachment and proliferation were improved and cell spreading was enhanced on hydrothermally treated specimens compared with untreated ones. Improved wettability, Ca incorporation and negative surface due to interstitial N were believed to be the main reasons. Hydrothermal treatment is expected to make TiN a promising dental implant coating with excellent abrasion resistance and good soft tissue affinity. - Highlights: • Ca was incorporated into TiN surface while not sacrificing its hardness. • Interstitial N due to oxidation promoted Ca adsorption and cell adhesion. • Hydrothermal treatment makes TiN a promising coating for dental implant.

  1. Effect of Fe2B boride orientation on abrasion wear resistance of Fe-B cast alloy

    Directory of Open Access Journals (Sweden)

    Da-wei Yi

    2017-07-01

    Full Text Available The microstructures and abrasion wear resistance of directional solidification Fe-B alloy have been investigated using optical microscopy, X-ray diffraction, scanning electron microscopy and laser scanning microscopy. The results show that the microstructure of as-cast Fe-B alloy consists of ferrite, pearlite and eutectic boride. After heat treatment, the microstructure is composed of boride and martensite. The plane which is perpendicular to the boride growth direction possesses the highest hardness. In two-body abrasive wear tests, the silicon carbide abrasive can cut the boride and martensite matrix synchronously, and the wear mechanism is micro cutting mechanism. The worn surface roughness and the wear weight loss both increase with the increasing contact load. Moreover, when the boride growth direction is perpendicular to the worn surface, the highest hardness plane of the boride can effectively oppose abrasion, and the martensite matrix can surround and support borides perfectly.

  2. Study of abrasive resistance of foundries models obtained with use of additive technology

    Science.gov (United States)

    Ol’khovik, Evgeniy

    2017-10-01

    A problem of determination of resistance of the foundry models and patterns from ABS (PLA) plastic, obtained by the method of 3D printing with using FDM additive technology, to abrasive wear and resistance in the environment of foundry sand mould is considered in the present study. The description of a technique and equipment for tests of castings models and patterns for wear is provided in the article. The manufacturing techniques of models with the use of the 3D printer (additive technology) are described. The scheme with vibration load was applied to samples tests. For the most qualitative research of influence of sandy mix on plastic, models in real conditions of abrasive wear have been organized. The results also examined the application of acrylic paintwork to the plastic model and a two-component coating. The practical offers and recommendation on production of master models with the use of FDM technology allowing one to reach indicators of durability, exceeding 2000 cycles of moulding in foundry sand mix, are described.

  3. In Vitro Assessment of the Abrasion Resistance of Two Types of Artificial Teeth Submitted to Brushing.

    Science.gov (United States)

    Policastro, Vivian Barnabé; Giro, Gabriela; Leite, Andressa Rosa Perin; Mendoza-Marin, Danny Omar; Paleari, André Gustavo; Compagnoni, Marco Antonio; Pero, Ana Carolina

    2016-08-01

    To assess the effect of brushing with different solutions on the abrasion resistance of two types of acrylic resin teeth. Maxillary premolars from two types of acrylic teeth (Biotone and Biotone IPN) were divided into six groups (n = 12), according to the solution used during brushing: distilled water (control), coconut soap, or dentifrice. A mechanical brushing machine was used to simulate approximately 1 year of brushing (11,000 strokes). The weight loss (WL) of teeth was obtained from the difference between the initial (IW) and final weight (FW) of each specimen, and the mean of percentage of weight loss (PWL) was calculated for each group. Data were analyzed using the Kruskal-Wallis test, followed by Bonferroni's post-test comparison (α = 0.05). A statistically significant difference was found for the factor solution (p Brushing using dentifrice caused the highest values of weight loss (-0.50%), in comparison with the groups brushed with coconut soap (0.00%) or distilled water (0.00%). For both types of artificial teeth, brushing with dentifrice produced higher abrasion than brushing with coconut soap or water. © 2016 by the American College of Prosthodontists.

  4. Final Technical Report: Development of an Abrasion-Resistant Antisoiling Coating for Front-Surface Reflectors

    Energy Technology Data Exchange (ETDEWEB)

    Gee, Randy C. [Sundog Solar Technology, Arvada, CO (United States)

    2017-07-18

    A high-performance reflective film has been successfully developed for Concentrating Solar Power (CSP) solar concentrators. Anti-soiling properties and abrasion resistance have been incorporated into the reflector to reduce reflector cleaning costs and to enhance durability. This approach has also resulted in higher reflectance and improved specularity. From the outset of this project we focused on the use of established high-volume roll-to-roll manufacturing techniques to achieve low manufacturing costs on a per ubit area basis. Roll-to-roll manufacturng equipment has a high capital cost so there is an entire industry devoted to roll-to-roll “toll” manufacturing, where the equipment is operated “around the clock” to produce a multitude of products for a large variety of uses. Using this approach, the reflective film can be manufactured by toll coaters/converters on an as-needed basis.

  5. The role of the microfissuration of the rock matrix in the abrasion resistance of ornamental granitic rocks

    Science.gov (United States)

    Rodríguez-Rey, Angel; Sanchez-Delgado, Nuria; Camino, Clara; Calleja, Lope; Ruiz de Argandoña, Vicente G.; Setien, Alexia

    2015-04-01

    The microcrack density and the abrasion resistance of five ornamental granites (Albero, Gris Alba, Mondariz, Rosa Porriño and Traspieles) from Galicia (NW Spain) have been quantified as part of a research aimed to interpret the cuttability of the rocks in relation to the petrophysical properties of the rock matrix. Large blocks from the quarries have been cut with an industrial saw and the microcrack density and the abrasion resistance have been measured in two surfaces: H, parallel to the cut surface; T, perpendicular both to the cut surface and the cutting direction. Both planes are perpendicular to the rift plane, as it is known in quarry works. The microcrack density has been quantified following an stereological procedure applied to polished sections imaged under scanning electron microscopy. The magnification of the images allowed the study of microcracks as narrow as 2 microns in aperture. The density has been quantified in terms of length of microcrack traces per surface unit so possible anisotropies of the microcrack network could be detected. The obtained values are in the typical range for this type of rocks although the Traspieles granite shows a higher value due to its weathering degree (H: 5.11, T: 5.37 mm/mm2). The values measured in the two surfaces (H and T) are quite similar in four of the rocks; only the Albero granite shows a marked anisotropy (H: 2.76 T: 3.53 mm/mm2). The abrasion resistance of the rocks has been measured following the european standard EN 14157:2004 using the capon method. The rocks can be classified in two groups according to their abrasion resistance. Rosa Porriño, Gris Alba and Mondariz granites are the more resistant to abrasion with values around 16-17 mm. Albero and Traspieles granites are less resistant with values higher than 19 mm. The results show a good correlation between the microcrack density and the abrasion resistance. As can be expected the rocks with high microcrack density show low abrasion resistance. The

  6. Validation of the abrasion resistance test protocols and performance criteria of EN13595: The probability of soft tissue injury to motorcycle riders by abrasion resistance of their clothing.

    Science.gov (United States)

    Meredith, Lauren; Hurren, Christopher; Clarke, Elizabeth; Fitzharris, Michael; Baldock, Matthew; de Rome, Liz; Olivier, Jake; Brown, Julie

    2017-06-01

    Motorcyclists represent an increasing proportion of road users globally and are increasingly represented in crash statistics. Soft tissue injuries are the most common type of injuries to crashed motorcyclists. These injuries can be prevented through the use of protective clothing designed for motorcycle use. However, the quality of such clothing is not controlled in many countries around the world. A European Standard was developed to assess the performance of clothing but as this is not mandatory, clothing certified to this Standard is difficult to obtain. Given the importance of this Standard, and that it has been validated only once, further validation work is required. In-depth crash investigation data were used to investigate the relationship between the abrasion resistance performance of clothing and real-world injury outcome. Clothing was collected from riders who crashed on public roads in Sydney and Newcastle, Australia. This clothing was tested according to the EU Standard and the time to hole was recorded. Hospital medical records were reviewed and the association between a rider suffering a soft tissue injury and the time-to-hole for the garment was examined. The probability of soft tissue injury for Level 1 Standard garments was between 40-60%, but more than 60% of garments tested failed to meet the minimum requirement. The findings of this study provide qualified support for the Standard, with a marginal association between time-to-hole and injury being found. This work supports the need for improved safety performance and an increased number of high performing garments being available to motorcyclists. Copyright © 2017 Elsevier Ltd and National Safety Council. All rights reserved.

  7. Deposition of TiC film on titanium for abrasion resistant implant material by ion-enhanced triode plasma CVD

    Energy Technology Data Exchange (ETDEWEB)

    Zhu Yuhe, E-mail: zyh1120@hotmail.co.jp [School of Stomatology, China Medical University, Shen Yang (China); Wang Wei; Jia Xingya [School of Stomatology, China Medical University, Shen Yang (China); Akasaka, Tsukasa [Department of Health Science, School of Dental Medicine Hokkaido University, Sapporo (Japan); Liao, Susan [School of Materials Science and Engineering, Nanyang Technological University (Singapore); Watari, Fumio [Department of Health Science, School of Dental Medicine Hokkaido University, Sapporo (Japan)

    2012-12-01

    Highlights: Black-Right-Pointing-Pointer Deposition of Titanium Carbide (TiC) layer on titanium (Ti) surface has been demonstrated by an ion-enhanced triode plasma chemical vapor deposition (CVD) method. Black-Right-Pointing-Pointer The Vickers hardness of surface carbide was more than 2000, which confirmed its high abrasion resistance. Black-Right-Pointing-Pointer Physical and mechanical properties of the deposited TiC film on Ti were investigated to examine its potential application as an abrasion resistant implant material. - Abstract: Deposition of titanium carbide (TiC) layer on titanium (Ti) surface has been demonstrated by an ion-enhanced triode plasma chemical vapor deposition (CVD) method using a TiCl{sub 4} + CH{sub 4} + H{sub 2} gas mixture. Physical and mechanical properties of the deposited TiC film on Ti were investigated to examine its potential application as an abrasion resistant implant material. X-ray diffraction (XRD) showed that the specimen was consisted of TiC and Ti. Carbide layer of about 6 {mu}m thickness was observed on the cross section of the specimen by scanning electron microscopy (SEM). The Vickers hardness of surface carbide was more than 2000, which confirmed its high abrasion resistance.

  8. Preparation and characterization of poly(vinylidene fluoride)/nanoclay nanocomposite flat sheet membranes for abrasion resistance.

    Science.gov (United States)

    Lai, Chi Yan; Groth, Andrew; Gray, Stephen; Duke, Mikel

    2014-06-15

    Membranes with more resilience to abrasive wear are highly desired in water treatment, especially for seawater desalination. Nanocomposite poly(vinylidene fluoride) (PVDF)/nanoclay membranes were prepared by phase inversion and then tested for abrasion resistance. Their material properties were characterized using Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), tensile testing, scanning electron microscopy (SEM) and energy dispersive spectroscopy (EDS). Nanoclay Cloisite(®) 15A was utilised as the inorganic nanoparticle incorporated into PVDF. FTIR results showed a shifting of the PVDF crystalline phase from α to β thus indicating that the nanoclay altered the PVDF host material's structure and mechanical properties in terms of stiffness and toughness. Water permeation test showed that nanoclay at low concentration tended to reduce water flux. All nanocomposite membranes, with between 1 wt% and 5 wt% initial nanoclay loading, were more abrasion resistant than the control PVDF membrane. However, the 1 wt% exhibited superior resistance, lasting two times longer than the reference PVDF membrane under the same abrasive condition. The 1 wt% nanoclay membrane appeared less abraded by SEM observation, while also having the greatest tensile strength improvement (from 4.5 MPa to 4.9 MPa). This membrane also had the smallest agglomerated nanoclay particle size and highest toughness compared to the higher nanoclay content membranes. Nanoclays are therefore useful for improving abrasion resistance of PVDF membranes, but optimal loadings are essential to avoid losing essential mechanical properties. Copyright © 2014 Elsevier Ltd. All rights reserved.

  9. Effect of Austenite Transformation on Abrasive Wear and Corrosion Resistance of Spheroidal Ni-Mn-Cu Cast Iron

    Directory of Open Access Journals (Sweden)

    Medyński D.

    2016-09-01

    Full Text Available Within the presented work, the effect of austenite transformation on abrasive wear as well as on rate and nature of corrosive destruction of spheroidal Ni-Mn-Cu cast iron was determined. Cast iron contained: 3.1÷3.4 %C, 2.1÷2.3 %Si, 2.3÷3.3 %Mn, 2.3÷2.5 %Cu and 4.8÷9.3 %Ni. At a higher degree of austenite transformation in the alloys with nickel equivalent below 16.0%, abrasive wear resistance was significantly higher. Examinations of the corrosion resistance were carried out with the use of gravimetric and potentiodynamic method. It was shown that higher degree of austenite transformation results in significantly higher abrasive wear resistance and slightly higher corrosion rate, as determined by the gravimetric method. However, results of potentiodynamic examinations showed creation of a smaller number of deep pinholes, which is a favourable phenomenon from the viewpoint of corrosion resistance.

  10. Application of ceramic coating to improve abrasive wear resistance of die inserts used to press-mould stampings of refractories

    Directory of Open Access Journals (Sweden)

    A. W. Orłowicz

    2017-01-01

    Full Text Available The paper presents results of a study on abrasive wear resistance of die inserts for composite moulds used to pressmould stampings from refractory materials, determined based on susceptibility to scratching with a diamond indenter. For the study, two inserts of high-chromium cast iron were prepared, of which one was provided with a ceramic coating (60 % Al2O3 + 40 % TiO2 with a metallic interlayer (NiAlCrSi. Both layers were deposited by means of the Atmospheric Plasma Spraying (APS method. The obtained scratch test results indicate that with the use of the same load force (20 N, die inserts with ceramic coating are characterized with less indenter penetration depth which should translate to higher resistance to abrasive wear.

  11. Improvement in Abrasion Wear Resistance and Microstructural Changes with Deep Cryogenic Treatment of Austempered Ductile Cast Iron (ADI)

    Science.gov (United States)

    Šolić, Sanja; Godec, Matjaž; Schauperl, Zdravko; Donik, Črtomir

    2016-10-01

    The application of a deep cryogenic treatment during the heat-treatment processes for different types of steels has demonstrated a significant influence on their mechanical and tribological properties. A great deal of research was conducted on steels, as well as on other kinds of materials, such as hard metal, gray cast iron, aluminum, aluminum alloys, etc., but not on austempered ductile iron (ADI). In this research the influence of a deep cryogenic treatment on the microstructure and abrasive wear resistance of austempered ductile iron was investigated. The ductile cast iron was austempered at the upper ausferritic temperature, deep cryogenically treated, and afterwards tempered at two different temperatures. The abrasion wear resistance was tested using the standard ASTM G65 method. The microstructure was characterized using optical microscopy, field-emission scanning electron microscopy, electron back-scattered diffraction, and X-ray diffraction in order to define the microstructural changes that influenced the properties of the ADI. The obtained results show that the deep cryogenic treatment, in combination with different tempering temperatures, affects the matrix microstructure of the austempered ductile iron, which leads to an increase in both the abrasion wear resistance and the hardness.

  12. Abrasion-resistant concrete mix designs for precast bridge deck panels.

    Science.gov (United States)

    2010-08-01

    The report documents laboratory investigations undertaken to develop high performance concrete (HPC) for precast and pre-stressed bridge deck components that would reduce the life-cycle cost of bridges by improving the studded tire wear (abrasion) re...

  13. Cleaning, abrasion, and polishing effect of novel perlite toothpaste abrasive.

    Science.gov (United States)

    Wang, Bo

    2013-01-01

    This study was intended to optimize perlite particle size and morphology for better tooth cleaning and lower tooth abrasion, and to evaluate the performance of a whitening toothpaste containing the optimized perlite abrasive for tooth cleaning, abrasion, and polishing. Perlite toothpaste abrasive samples were prepared by air classifying a commercial expanded perlite product. The tooth cleaning and abrasion properties for these classified perlite samples were reported via the pellicle cleaning ratio (PCR) and relative dentin abrasion (RDA). Performance of the whitening toothpaste containing the optimized perlite abrasive in tooth cleaning, polishing, and abrasion was evaluated against a widely used synthetic high-cleaning silica. Air classification removes large perlite particles and also physically changes perlite particle morphology from mostly three dimensional and angular particles to mainly two dimensional and platy particles. All the classified samples show good tooth cleaning effect, but tooth abrasion decreases significantly with decreasing particle size. Compared to high-cleaning silica whitening toothpaste, the whitening toothpaste containing the optimized perlite abrasive (PerlClean) is slightly better at tooth cleaning, lower in tooth abrasion, and significantly better at tooth polishing. Fine platy perlite particles are effective in tooth cleaning with low tooth abrasion. The enhanced performance of optimized perlite toothpaste abrasive compared to high-cleaning silica in a whitening toothpaste is attributed to the optimized particle size distribution and the unique platy particle geometry.

  14. Employee resistance and injury during commercial robberies.

    Science.gov (United States)

    Jones, Jennifer; Casteel, Carri; Peek-Asa, Corinne

    2015-05-01

    To examine the association between employee resistance and injury and examine whether type or location of property stolen was associated with employee resistance during commercial robberies in a large metropolitan city. Robbery data were abstracted from police crime reports between 2008 and 2012. Log binomial regression models were used to identify predictors of employee resistance and to evaluate the association between employee resistance and injury. Employees resisted a robber in nearly half of all robbery events. Active employee resistance was significantly associated with employee injury (Adj PR: 1.49, 95% confidence interval, 1.34 to 1.65). Goods being stolen were associated with active employee resistance and employee injury, whereas cash only being stolen was inversely associated with employee injury. Results suggest that employee training in nonresistance can be an important strategy in protecting employees working with the exchange of cash and goods.

  15. Effect of denture cleaning on abrasion resistance and surface topography of polymerized CAD CAM acrylic resin denture base.

    Science.gov (United States)

    Shinawi, Lana Ahmed

    2017-05-01

    The application of computer-aided design computer-aided manufacturing (CAD CAM) technology in the fabrication of complete dentures, offers numerous advantages as it provides optimum fit and eliminates polymerization shrinkage of the acrylic base. Additionally, the porosity and surface roughness of CAD CAM resins is less compared to conventionally processed resins which leads to a decrease in the adhesion of bacteria on the denture base, which is associated with many conditions including halitosis and aspiration pneumonia in elderly denture wearers. To evaluate the influence of tooth brushing with dentifrices on CAD CAM resin blocks in terms of abrasion resistance, surface roughness and scanning electron photomicrography. This experimental study was carried out at the Faculty of Dentistry of King Abdulaziz University during 2016. A total of 40 rectangular shaped polymerized CAD CAM resin samples were subjected to 40.000 and 60.000 brushing strokes under a 200-gram vertical load simulating three years of tooth brushing strokes using commercially available denture cleaning dentifrice. Data were analyzed by SPSS version 20, using descriptive statistics and ANOVA. ANOVA test revealed a statistical significant weight loss of CAD CAM acrylic resin denture base specimens following 40.000 and 60.000 brushing strokes as well as a statistical significant change (p=0.0.5) in the surface roughness following brushing. The CAD CAM resin samples SEM baseline imaging revealed a relatively smooth homogenous surface, but following 40,000 and 60,000 brushing strokes, imaging displayed the presence of small scratches on the surface. CAD CAM resin displayed a homogenous surface initially with low surface roughness that was significantly affected following simulating three years of manual brushing, but despite the significant weight loss, the findings are within the clinically acceptable limits.

  16. Improved Corrosion and Abrasion Resistance of Organic-Inorganic Composite Coated Electro-galvanized Steels for Digital TV Panels

    Energy Technology Data Exchange (ETDEWEB)

    Jo, Du-Hwan; Noh, Sang-Geol; Park, Jong-Tae; Kang, Choon-Ho [POSCO Technical Research Laboratories, Pohang (Korea, Republic of)

    2015-10-15

    Recently, household electronic industries require environmentally-friendly and highly functional steels in order to enhance the quality of human life. Customers especially require both excellent corrosion and abrasion resistant anti-fingerprint steels for digital TV panels. Thus POSCO has developed new functional electro-galvanized steels, which have double coated layers with organic-inorganic composites on the zinc surface of the steel for usage as the bottom chassis panel of TVs. The inorganic solution for the bottom layer consists of inorganic phosphate, magnesium, and zirconium compounds with a small amount of epoxy binder, and affords both improved adhesion properties by chemical conversion reactions and corrosion resistance due to a self-healing effect. The composite solution for the top layer was prepared by fine dispersion of organic-inorganic ingredients that consist of a urethane modified polyacrylate polymer, hardener, silica sol and a titanium complex inhibitor in aqueous media. Both composite solutions were coated on the steel surface by using a roll coater and then cured through an induction furnace in the electro-galvanizing line. New anti-fingerprint steel was evaluated for quality performance through such procedures as the salt spray test for corrosion resistance, tribological test for abrasion resistance, and conductivity test for surface electric conductance regarding to both types of polymer resin and coating weight of composite solution. New composite coated anti-fingerprint steels afford both better corrosion resistance and abrasion properties compared to conventional anti-fingerprint steel that mainly consists of acrylate polymers. Detailed discussions of both composite solutions and experimental results suggest that urethane modifications of acrylate polymers of composite solutions play a key role in enhanced quality performances.

  17. The Abrasion Resistance and Adhesion of Hfcvd Boron and Silicon-Doped Diamond Films on WC-Co Drawing Dies

    Science.gov (United States)

    Wang, Liang; Liu, Jinfei; Tang, Tang; Sun, Fanghong; Xie, Nan

    Diamond films have been deposited on the interior hole surface of cobalt-cemented tungsten carbide (WC-Co) drawing dies from acetone, trimethyl borate (C3H9BO3), tetraethoxysilane (C8H20O4Si, TEOS) and hydrogen mixture by hot-filament chemical vapor deposition (HFCVD) method. The structures and quality of as-deposited diamond films are characterized with field-emission scanning electron microscopy (FESEM) and Raman spectroscopy. The abrasion ratio and the adhesive strength of as-deposited diamond films are evaluated by copper wire drawing tests and ultrasonic lapping tests, respectively. The results suggest that diamond films with small grain size and high growth rate can be obtained due to the mutual effects of boron and silicon impurities in the gas phases. The results of ultrasonic lapping tests show that diamond films doped with boron and/or silicon can bear the severe erosion of the large diamond powder. Diamond films peeling off within the reduction zone of the drawing dies cannot be observed after testing of 2h. The abrasion ratio of boron and silicon-added diamond films is five times that of diamond films without any addition. Adding boron and/or silicon in the diamond films is proved to be an efficient way to obtain high-adhesive-strength and high-abrasion-resistance diamond-coated drawing dies.

  18. HVOF- and HVAF-Sprayed Cr3C2-NiCr Coatings Deposited from Feedstock Powders of Spherical Morphology: Microstructure Formation and High-Stress Abrasive Wear Resistance Up to 800 °C

    Science.gov (United States)

    Janka, L.; Norpoth, J.; Trache, R.; Thiele, S.; Berger, L.-M.

    2017-10-01

    Chromium carbide-based coatings are commonly applied to protect surfaces against wear at high temperatures. This work discusses the influence of feedstock powder and spray torch selection on the microstructure and high-stress abrasion resistance of thermally sprayed Cr3C2-NiCr coatings. Four commercial feedstock powders with spherical morphology and different microstructures were deposited by different high-velocity spray processes, namely third-generation gas- and liquid-fueled HVOF torches and by the latest generation HVAF torch. The microstructures of the coatings were studied in the as-sprayed state and after various heat treatments. The high-stress abrasion resistance of as-sprayed and heat-treated coatings was tested at room temperature and at 800 °C. The study reveals that the selection of the spray torch mainly affects the room temperature abrasion resistance of the as-sprayed coatings, which is due to differences in the embrittlement of the binder phase generated by carbide dissolution. At elevated temperatures, precipitation and growth of secondary carbides yields a fast equalization of the various coatings microstructures and wear properties.

  19. Abrasive wear resistance optimization of three different carbide coatings by the Taguchi method

    Energy Technology Data Exchange (ETDEWEB)

    Guer, Ali Kaya [Firat Univ., Elazig (Turkey). Dept. of Metallurgy and Materials; Kaya, Sinan [Firat Univ., Elazig (Turkey). Faculty of Technology

    2017-06-01

    In this study, FeCrC, SiC and B{sub 4}C powders were alloyed on the surface of AISI 430 ferritic stainless steel by plasma arc welding. The mass losses of the abrasive wear of the AISI 430 substrate were examined under the loads of 6, 10 and 16 N and in the distances of 10, 20 and 30 m by using Taguchi design method. The results of abrasive wear test were optimized by the minimum optimal control characteristics of the Taguchi procedure and the results were analyzed by using graphical methods. The Taguchi procedure is an important approach to achieve high quality without increasing the cost during the optimization of process parameters. The orthogonal planes of maximum effects of the controllable process parameters and minimum effects of uncontrollable process parameters were employed in the Taguchi method.

  20. Micro-abrasion resistance of thermochemically treated steels in aqueous solutions : mechanisms, maps, materials selection

    OpenAIRE

    Mathew, M. T.; Stack, M. M.; Matijevic, B.; Rocha, L. A.; Ariza, E.

    2008-01-01

    The area of micro-abrasion is an interesting and relatively recent area in tribo-testing methodologies, where small particles of less than 10 mm are employed between interacting surfaces. It is topical for a number of reasons; its direct relation to the mechanisms of the wear process in bio-tribological applications, ease in conducting tests and the good repeatability of the test results. It has widespread applications in conditions used in the space and offshore industries to bio-en...

  1. Development of Abrasion-Resistant Coating for Solar Reflective Films. Cooperative Research and Development Final Report, CRADA Number CRD-07-247

    Energy Technology Data Exchange (ETDEWEB)

    Gray, Matthew [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2015-10-01

    The purpose of this CRADA is to develop an abrasion-resistant coating, suitable for use on polymeric-based reflective films (e.g., the ReflecTech reflective film), that allows for improved scratch resistance and enables the use of aggressive cleaning techniques (e.g., direct contact methods like brushing) without damaging the specular reflectance properties of the reflective film.

  2. Effect of high-manganese cast steel strain hardening on the abrasion wear resistance in a mixture of SiC and water

    Directory of Open Access Journals (Sweden)

    Kalandyk B.

    2013-12-01

    Full Text Available The study attempts to determine the impact of the high-manganese cast steel strain hardening on its abrasion wear resistance in a mixture of SiC and water prepared in accordance with ASTM G75. For tests, the high-manganese cast steel containing 10.7, 17.9 and 20.02% Mn was selected. The results of microstructure examinations and abrasion wear resistance tests carried out on the material in non-hardened condition and after strain hardening with a force of 539.55kN were disclosed. Additionally, the surface of samples after a 16-hour cycle of abrasion tests was examined. Moreover, based on the obtained results, the effect of different contents of Mn in cast steel was studied, mainly in terms of its impact on the abrasion wear resistance. The results obtained on the tested materials were compared with the results obtained on the low-alloyed abrasion wear-resistant cast steel L35GSM.

  3. Analysis Of The Austenite Grain Growth In Low-Alloy Boron Steel With High Resistance To Abrasive Wear

    Directory of Open Access Journals (Sweden)

    Białobrzeska B.

    2015-09-01

    Full Text Available Today low-alloy steels with boron achieve high resistance to abrasive wear and high strength. These features are obtained by using advanced technology of manufacturing. This makes boron steels increasingly popular and their application more diverse. Application of these steels can extend the lifetime of very expensive machine construction in many industries such as mining, the automotive, and agriculture industries. An interesting subgroup of these materials is steel with boron intended for heat treatment. These steels are supplied by the manufacturer after cold or hot rolling so that it is possible for them to be heat treated in a suitable manner by the purchaser for its specific application. Very important factor that determines the mechanical properties of final product is austenite grain growth occurring during hot working process such us quenching or hot rolling. Investigation of the effect of heating temperature and holding time on the austenite grain size is necessary to understand the growth behavior under different conditions. This article presents the result of investigation of austenite grain growth in selected low-allow boron steel with high resistance to abrasive wear and attempts to describe the influence of chemical composition on this process.

  4. Halogen-Free Phosphonate Ionic Liquids as Precursors of Abrasion Resistant Surface Layers on AZ31B Magnesium Alloy

    Directory of Open Access Journals (Sweden)

    Tulia Espinosa

    2015-01-01

    Full Text Available Surface coatings formed by immersion in the ionic liquids (ILs 1,3-dimethylimidazolium methylphosphonate (LMP101, 1-ethyl-3-methylimidazolium methylphosphonate (LMP102 and 1-ethyl-3-methylimidazolium ethylphosphonate (LEP102 on magnesium alloy AZ31B at 50 °C have been studied. The purpose of increasing the temperature was to reduce the immersion time, from 14 days at room temperature, to 48 hours at 50 °C. The abrasion resistance of the coated alloy was studied by microscratching under progressively increasing load, and compared with that of the uncoated material. The order of abrasion resistance as a function of the IL is LEP102 > LMP101 > LMP102, which is in agreement with the order obtained for the coatings grown at room temperature. The maximum reduction in penetration depth with respect to the uncovered alloy, of a 44.5%, is obtained for the sample treated with the ethylphosphonate LEP102. However, this reduction is lower than that obtained when the coating is grown at room temperature. This is attributed to the increased thickness and lower adhesion of the coatings obtained at 50 °C, particularly those obtained from methylphosphonate ionic liquids. The results are discussed from SEM-EDX and profilometry.

  5. The Abrasive Wear Resistance of the Segmented Linear Polyurethane Elastomers Based on a Variety of Polyols as Soft Segments

    Directory of Open Access Journals (Sweden)

    Konrad Kwiatkowski

    2017-12-01

    Full Text Available The presented results make an original contribution to the development of knowledge on the prediction and/or modeling of the abrasive wear properties of polyurethanes. A series of segmented linear polyurethane elastomers (PUR—In which the hard segments consist of 4,4′-methylene bis(phenylisocyanate and 1,4-butanodiol, whilst polyether, polycarbonate, or polyester polyols constitute the soft segments—Were synthesized and characterized. The hardness and wear performance as functions of the variable chemical composition of polyurethane elastomers were evaluated in order to define the relationship between studied factors. The microstructure was characterized in detail, including analysis of the hydrogen bonding by Fourier transformed infrared (FT-IR spectroscopy and the phase structure by X-ray scattering (WAXS and differential scanning calorimetry (DSC methods. The presented studies provide the key features of the polymer composition affecting the abrasive resistance as well as attempts to explain the origin of the differences in the polyurethane elastomers’ performance.

  6. Influence of Hardness, Matrix and Carbides in Combination with Nitridation on Abrasive Wear Resistance of X210Cr12 Tool Steel

    Directory of Open Access Journals (Sweden)

    Martin Orečný

    2016-10-01

    Full Text Available Materials used in abrasive wear conditions are usually selected according to their microstructure and hardness, however, other factors such as grain size, matrix saturation, carbides size and morphology are rarely considered. Therefore, the present study deals with the influence of different heat and chemical-heat treatments including their combination on abrasive wear resistance of X210Cr12 tool steel. The effects of material hardness, carbide morphology and microstructure on wear resistance after quenching and nitriding were also investigated. One sample series was quenched after austenitization at 960 °C for 20 min and tempered at 180 °C for 2 h. The second sample series was quenched from 1060 °C austenitization for 20 min and afterwards twice tempered at 530 °C for 1 h. From both the quenched and tempered states, one half of the samples was gas nitrided in NH3 atmosphere for 3 h and then diffusion annealed in N2 atmosphere for 4 h. Abrasion wear tests were performed by sliding the samples on Al2O3 paper. The samples weight loss was considered the main criterion for the wear resistance evaluation. The microstructures, nitrided layers and worn surfaces were observed using SEM microscopy. The highest abrasion wear resistance was obtained for the nitrided samples that were previously quenched from 1060 °C and tempered at 530 °C.

  7. Systems for pipeline drainage and drying: pigs pass with flying colors. Robust polyurethane elastomer materials for made-to-measure, abrasion resistant pipeline pigs

    Energy Technology Data Exchange (ETDEWEB)

    Els, Detlev [Weatherford Kopp GmbH, Lingen (Germany); Passmann, Dirk [Bayer MaterialScience AG, Leverkusen (Germany)

    2008-12-15

    The pipeline pig system developed for drainage of a long offshore pipeline with two different diameters was a world first that placed extreme demands on the pig design and the materials used. The polyurethane elastomer Baytec registered Q. used for the pig's disks, passed this ''acid test'' with flying colors thanks to its superior properties - accurately dimensioned cast disks, variable hardness, exceptional abrasion resistance, high elasticity, tear strength and resistance to chemicals. (orig.)

  8. Sealing ability, water sorption, solubility and toothbrushing abrasion resistance of temporary filling materials.

    Science.gov (United States)

    Pieper, C M; Zanchi, C H; Rodrigues-Junior, S A; Moraes, R R; Pontes, L S; Bueno, M

    2009-10-01

    To evaluate marginal seal, water sorption, solubility and loss of mass after brushing of several temporary filling materials. For marginal seal, Class I cavities, including endodontic access preparations, were made in human molar teeth and restored using one or other of several temporary filling materials (n = 10): zinc oxide/calcium sulphate-based cement (Cavit, 3M,ESPE, St. Paul, MN, USA), zinc oxide/eugenol cement (IRM, Dentsply Caulk, Milford, DE, USA), glass ionomer cement (Vidrion R, SSWhite, Rio de Janeiro, RJ, Brazil) or a dimethacrylate-based filling (Bioplic, Biodinâmica, Londrina, PR, Brazil). Dye penetration was assessed after thermocycling and immersion in 0.5% basic fuchsine solution. For water sorption, solubility and loss of mass analyses, disc-shaped specimens were made. Water sorption and solubility were evaluated by mass alteration after storage in distilled water for 7 days (n = 7). Loss of mass was calculated based on the difference of mass after abrasion with a toothbrush (n = 5), and surfaces were analysed by SEM. Data of water sorption, solubility and loss of mass were submitted to anova and Tukey's test, and marginal sealing data to Kruskal-Wallis test (P Cavit had the greatest water sorption and solubility. Vidrion R and Bioplic had the lowest solubility. Loss of mass after brushing was higher for Cavit, followed by Bioplic, IRM and Vidrion R. Cavit and Vidrion R were worn aggressively by brushing. The resin-based temporary filling Bioplic produced the best marginal seal, and was associated with the lowest water sorption, solubility and loss of mass.

  9. Antimicrobial photodynamic therapy with RLP068 kills methicillin-resistant Staphylococcus aureus and improves wound healing in a mouse model of infected skin abrasion PDT with RLP068/Cl in infected mouse skin abrasion.

    Science.gov (United States)

    Vecchio, Daniela; Dai, Tianhong; Huang, Liyi; Fantetti, Lia; Roncucci, Gabrio; Hamblin, Michael R

    2013-09-01

    Photodynamic therapy (PDT) is an alternative treatment for infections that can kill drug resistant bacteria without damaging host-tissue. In this study we used bioluminescent methicillin-resistant Staphylococcus aureus, in a mouse skin abrasion model, to investigate the effect of PDT on bacterial inactivation and wound healing. RLP068/Cl, a tetracationic Zn(II)phthalocyanine derivative and toluidine blue (TBO) were used. The light-dose response of PDT to kill bacteria in vivo and the possible recurrence in the days post-treatment were monitored by real-time bioluminescence imaging, and wound healing by digital photography. The results showed PDT with RLP068/Cl (but not TBO) was able to kill bacteria, to inhibit bacterial re-growth after the treatment and to significantly accelerate the wound healing process (© 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim). Copyright © 2013 WILEY-VCH Verlag GmbH & Co. KGaA, Weinheim.

  10. OPTIMIZATION OF THE COMPOSITION AND TECHNOLOGY OF THE ABRASION-RESISTANT CAST-IRONS MELTING

    Directory of Open Access Journals (Sweden)

    A. I. Garost

    2004-01-01

    Full Text Available Тhе methods of the service durability increase of wear resistant cast irons are analyzed. There are developed the compositions of economically-alloyed cast irons with low content of nickel and other deficient elements, being exploited both in cast and in thermotreated state. The composition of antifriction gray cast iron with increased exploitation characteristics is offered.

  11. Maintenance and Preservation of Concrete Structures. Report 3. Abrasion-Erosion Resistance of Concrete.

    Science.gov (United States)

    1980-07-01

    resistance involves a modification of the Los Angeles rattler (Scofield 1975). Concrete cylinders or cubes are placed in the machine and tumbled for... CONTRAT 5) ATA CMNTFC IIICU 385 I E.p....s e - F.u 5 IA# RIEIE5, ROOF? *Fpa*RSt ftaE A, --EtI PA.. ,.md II, CRD-C 9. ANA .REdF. IA.. ... 1.(2,. TIB

  12. Floor tile glass-ceramic glaze for improvement of the resistance to surface abrasion

    Energy Technology Data Exchange (ETDEWEB)

    Gajek, M; Lis, J; Partyka, J; Wojczyk, M, E-mail: mgajek@agh.edu.pl [AGH University of Science and Technology, Faculty of Materials Science and Ceramic, al. Mickiewicza 30, 30-059 Cracow (Poland)

    2011-10-29

    The results of research aimed at the study on frits and glass-ceramic glazes for floor tiles, based on compositions located in the primary field of cordierite crystallization within the system MgO-Al{sub 2}O{sub 3}-SiO{sub 2}, have been presented. The results comprise investigations on the frits crystallization abilities, stability of the crystallizing phase under conditions of single-stage a fast firing cycle (time below 60 minutes) depending on their chemical composition and the influence of the nucleation agents. The influence of the nucleating agents namely TiO{sub 2}, ZrO{sub 2}, V{sub 2}O{sub 5} on phase composition of obtained crystalline glazes, mechanical parameters and microstructure, has been examined. The strength tests proved increased mechanical resistance of crystalline glazes. Obtained glazes are characterized by high microhardness in range 6{approx}8 GPa, as well as the increased wear resistance measured by the loss of weight below 100 mg / 55 cm{sup 2} (PN-EN ISO 10545-7). Significant increase of these parameters as compared with non-crystalline glazes, where micro-hardness values range between 5{approx}6 GPa and the wear resistance values range from 120 to 200 mg, has been proved. Starting glasses (frits) and glazes of the ternary system MgO-SiO{sub 2}-Al{sub 2}O{sub 3}, were examined with use of DTA, XRD and SEM methods.

  13. Influence of Vanadium and Boron Additions on the Microstructure, Fracture Toughness, and Abrasion Resistance of Martensite-Carbide Composite Cast Steel

    Directory of Open Access Journals (Sweden)

    Waleed Elghazaly

    2016-01-01

    Full Text Available High chromium cast steel alloys are being used extensively in many industrial services where dry or wet abrasion resistance is required. Such steel castings are demanded for cement, stoneware pipes, and earth moving industries. In this research, five steel heats were prepared in 100 kg and one-ton medium frequency induction furnaces and then sand cast in both Y-block and final impact arm spare parts, respectively. Vanadium (0.5–2.5% and boron (120–150 ppm were added to the 18Cr-1.9C-0.5Mo steel heats to examine their effects on the steel microstructure, mechanical properties especially impact, fracture toughness and abrasion resistance. Changes in the phase transformation after heat treatment were examined using inverted, SEM-EDX microscopy; however, the abrasion resistance was measured in dry basis using the real tonnage of crushed and milled stoneware clay to less than 0.1 mm size distribution.

  14. Microstructure and Abrasive Wear Resistance of 18Cr-4Ni-2.5Mo Cast Steel

    Directory of Open Access Journals (Sweden)

    Kalandyk B.

    2012-12-01

    Full Text Available An influence of a decreased Cr content on the microstructure of the highly alloyed Cr-Ni cast steel, duplex type, melted under laboratory conditions, was characterized in the paper. The microstructure investigations were performed in the initial state and after the heat treatment (solution annealing at 1060°C as well as the phase transformation kinetics at continuous cooling was measured. The wear resistance of the investigated cast steel was tested and compared with the 24%Cr-5%Ni-2.5%Mo cast steel.

  15. Multiple insect resistance in 50 commercial corn hybrids, 2016

    Science.gov (United States)

    Commercial corn hybrids were screened for ear- and kernel-feeding insect resistance under field conditions at Tifton, GA. Nine hybrids were rated Very Good (VG), the highest rating for multiple insect resistance in 2016 (see following table). Thirteen were Good (G), 19 were Fair (F), and 13 were Poo...

  16. Abrasive wear behavior of heat-treated ABC-silicon carbide

    Energy Technology Data Exchange (ETDEWEB)

    Zhang, Xiao Feng; Lee, Gun Y.; Chen, Da; Ritchie, Robert O.; De Jonghe, Lutgard C.

    2002-06-17

    Hot-pressed silicon carbide, containing aluminum, boron, and carbon additives (ABC-SiC), was subjected to three-body and two-body wear testing using diamond abrasives over a range of sizes. In general, the wear resistance of ABC-SiC, with suitable heat treatment, was superior to that of commercial SiC.

  17. Development of the white cast iron with niobium alloy, heat treating, to wear of the abrasive resistance; Desenvolvimento de uma liga de ferro fundido branco alto cromo com niobio, tratada termicamente, para resistencia ao desgaste abrasivo

    Energy Technology Data Exchange (ETDEWEB)

    Farah, Alessandro Fraga

    1997-07-01

    This work presents the heat treatment and abrasion tests results of a white cast iron with niobium alloy. The hardening heat treatment were made 950, 1000, 1050 e 110 deg C temperatures cooled by forced air. The tempering treatment were made at 450, 500 e 550 deg C temperatures. The heat treating alloy were compared, in the abrasive tests, with commercial alloys used as hardfacing by welding process in wear pieces. The abrasion tests was realized in pin on disk test. Additional tests were carried out for microstructural characterization to identify the different phases presents in the alloys. In a general way, the alloy studies showed the best wear rate for the heat treatments that results in higher hardness. It performance was superior than that of the commercial alloys. (author)

  18. Antimicrobial photodynamic therapy with RLP068 kills methicillin-resistant Staphylococcus aureus and improves wound healing in a mouse model of infected skin abrasion

    Science.gov (United States)

    Vecchio, Daniela; Dai, Tianhong; Huang, Liyi; Fantetti, Lia; Roncucci, Gabrio; Hamblin, Michael R.

    2012-01-01

    Photodynamic therapy (PDT) is an alternative treatment for infections that can kill drug resistant bacteria without damaging host-tissue. In this study we used bioluminescent methicillin-resistant Staphylococcus aureus, in a mouse skin abrasion model, to investigate the effect of PDT on bacterial inactivation and wound healing. RLP068/Cl, a tetracationic Zn(II)phthalocyanine derivative and toluidine blue (TBO) were used. The light-dose response of PDT to kill bacteria in vivo and the possible recurrence in the days post-treatment were monitored by real-time bioluminescence imaging, and wound healing by digital photography. The results showed PDT with RLP068/Cl (but not TBO) was able to kill bacteria, to inhibit bacterial re-growth after the treatment and to significantly accelerate the wound healing process. Successive bioluminescence images of a representative mouse skin scratch model infected with 108 CFU MRSA. PMID:22987338

  19. Machining with abrasives

    CERN Document Server

    Jackson, Mark J

    2011-01-01

    Abrasive machining is key to obtaining the desired geometry and surface quality in manufacturing. This book discusses the fundamentals and advances in the abrasive machining processes. It provides a complete overview of developing areas in the field.

  20. Abrasion Testing Of Coated Plastic Lenses

    Science.gov (United States)

    Thiebaud, F.; Wegelin, H. P.

    1988-07-01

    The tumble abrasion test proposed by J.M. Young and J.D.Masso has been modified in order to produce uniform scratching of the lens surface under test and in order to simulate closely damage which occurs during normal wear in the field. The uniformity of the abrasion enables a quantitative measurement of the abrasion resistance by a simple determination of the scattered light. The test has been applied to coated and uncoated plastic ophthalmic lenses. The results show that the scratch resistance of the coated lenses depends strongly on the composition and on the thickness of the coating.

  1. Abrasion Testing of Products Containing Nanomaterials, SOP-R-2: Scientific Operating Procedure Series: Release (R)

    Science.gov (United States)

    2016-04-01

    Related Documents ASTM C 153-07 - Abrasion Resistance of Dimension Stone Subjected to Foot Traffic Using a Rotary Platform, Double-Head Abraser ASTM D...the process of wearing away by friction . Abrader - wear testing instrument to evaluate abrasion resistance; also referred to as an abraser. Abrasion...permits a return to its starting position. In the case of the rotary platform test method, it consists of one complete rotation of the specimen. ERDC

  2. The Influence Of Temperature Gradient On Stereological Parameters Of Carbide Phase On Cross-Section Of Abrasive Wear Resistant Chromium Cast Iron

    Directory of Open Access Journals (Sweden)

    Studnicki A.

    2015-09-01

    Full Text Available In the paper analysis of temperature gradient and parameters of structure on casting cross-section of abrasive wear resistant chromium cast iron at carbon content of 2,5%wt. and chromium 17%wt. with nickel and molybdenum additives are presented. The castings were made with use of special tester ϕ100mm (method of temperature gradient and derivative analysis with temperature recording in many points from thermal centre to surface (to mould of casting. Registered cooling curves were used to describe the temperature gradient on cross-section of analyzed casting. On the basis of determined curves of temperature gradient measurement fields were selected to make the quantitative studies of structure. The results of studies show significant influence of temperature gradient on quantitative parameters of chromium cast iron structure. Moreover was affirmed that exists a critical temperature gradient for which is present rapid change of quantitative parameters of chromium cast iron structure.

  3. Thermal aspects of ice abrasive water jet technology

    Directory of Open Access Journals (Sweden)

    Marko Jerman

    2015-08-01

    Full Text Available During the last few years, different research groups have been developing systems for the transition of abrasive water jet into ice abrasive water jet. The aim of this new technology is to make the technology cleaner from both practical and ecological points of view. Mineral abrasive is replaced with ice grains that melt away after the machining process, leaving the workpiece uncontaminated. Several different approaches to this technology were studied. Thermal aspects of integrating the ice abrasive water jet technology into commercially available machines were considered. The results and analyses of water temperature measurements on the ice abrasive water jet machine are presented in this article.

  4. Abrasion Resistance Enhancement of Ultrafine-structured WC-Co Coating Fabricated by using in situ Synthesized Composite Powder

    National Research Council Canada - National Science Library

    Haibin Wang Xiaoyan Song Chongbin Wei Yang Gao Guangsheng Guo

    2013-01-01

    .... The influences of the heat-treatment process on density of the feedstock powder, phase constitution and wear resistance of the resultant WC-Co coatings fabricated by high velocity oxy-fuel (HVOF) were investigated...

  5. The study of microstructure of wear-resistant coatings applied for protection from abrasive wear of horizontal and tilt drilling drill bits

    Science.gov (United States)

    Markova, I. Yu; Zakharova, E. S.; Maslov, A. L.; Polushin, N. I.; Laptev, A. I.; SOvchinnikova, M.

    2017-05-01

    Drill bits of the cutting type over the period of their existence have undergone significant changes - from the use of carbide cutters to diamond composite PDC elements, in which the diamond layer is applied to a hardmetal substrate. Using such elements, it was possible to significantly increase the service life of the drill bits, however, during work, there is a significant abrasive deterioration of the bit body, which does not fully realize the advantages of PDC elements. Therefore, to protect the body from wear use special wear-resistant coatings. This work is devoted to research of microstructural coatings, namely coatings brands WokaDur NiA, HR-6750, HR-6750 with sublayer Rock Dur 47 on various steel substrates which applied by the gas-thermal spraying in Ltd “Oerlikon Metko Rus”. They were examined with the use of scanning electron microscopy, X-ray phase analysis and a Vickers micro-hardness tester. It was established that the microhardness of the coating matrix is 590-660 HV, and the microhardness of tungsten carbide particles reinforcing the coating, is 2145-2455 HV.

  6. Empirical ranking of a wide range of WC-Co grades in terms of their abrasion resistance measured by the ASTM standard B 611-85 test

    CSIR Research Space (South Africa)

    O'Quigley, DGF

    1997-01-01

    Full Text Available tests The abrasion testing for all the grades was car- ried out in accordance with the ASTM Standard B 61 l-85 for the abrasion testing of cemented carbides. The abrasion tester consists of a wheel of diameter 169 mm and width 13 mm. The wheel... variation may be linked to the uncertainty in the grain L 0 5 10 15 20 25 30 35 40 45 50 Cobalt content (wt%) Fig. 1. Summary of the measured carbide grain size and the cobalt content of the WC-Co grades tested. The grades are divided into four sets...

  7. Photoresist-free patterning by mechanical abrasion of water-soluble lift-off resists and bare substrates: toward green fabrication of transparent electrodes.

    Directory of Open Access Journals (Sweden)

    Adam D Printz

    Full Text Available This paper describes the fabrication of transparent electrodes based on grids of copper microwires using a non-photolithographic process. The process--"abrasion lithography"--takes two forms. In the first implementation (Method I, a water-soluble commodity polymer film is abraded with a sharp tool, coated with a conductive film, and developed by immersion in water. Water dissolves the polymer film and lifts off the conductive film in the unabraded areas. In the second implementation (Method II, the substrate is abraded directly by scratching with a sharp tool (i.e., no polymer film necessary. The abraded regions of the substrate are recessed and roughened. Following deposition of a conductive film, the lower profile and roughened topography in the abraded regions prevents mechanical exfoliation of the conductive film using adhesive tape, and thus the conductive film remains only where the substrate is scratched. As an application, conductive grids exhibit average sheet resistances of 17 Ω sq(-1 and transparencies of 86% are fabricated and used as the anode in organic photovoltaic cells in concert with the conductive polymer, poly(3,4-ethylenedioxythiophene:poly(styrenesulfonate (PEDOT:PSS. Compared to devices in which PEDOT:PSS alone serves as an anode, devices comprising grids of copper/nickel microwires and PEDOT:PSS exhibit lowered series resistance, which manifests in greater fill factor and power conversion efficiency. This simple method of forming micropatterns could find use in applications where cost and environmental impact should be minimized, especially as a potential replacement for the transparent electrode indium tin oxide (ITO in thin-film electronics over large areas (i.e., solar cells or as a method of rapid prototyping for laboratory-scale devices.

  8. Photoresist-free patterning by mechanical abrasion of water-soluble lift-off resists and bare substrates: toward green fabrication of transparent electrodes.

    Science.gov (United States)

    Printz, Adam D; Chan, Esther; Liong, Celine; Martinez, René S; Lipomi, Darren J

    2013-01-01

    This paper describes the fabrication of transparent electrodes based on grids of copper microwires using a non-photolithographic process. The process--"abrasion lithography"--takes two forms. In the first implementation (Method I), a water-soluble commodity polymer film is abraded with a sharp tool, coated with a conductive film, and developed by immersion in water. Water dissolves the polymer film and lifts off the conductive film in the unabraded areas. In the second implementation (Method II), the substrate is abraded directly by scratching with a sharp tool (i.e., no polymer film necessary). The abraded regions of the substrate are recessed and roughened. Following deposition of a conductive film, the lower profile and roughened topography in the abraded regions prevents mechanical exfoliation of the conductive film using adhesive tape, and thus the conductive film remains only where the substrate is scratched. As an application, conductive grids exhibit average sheet resistances of 17 Ω sq(-1) and transparencies of 86% are fabricated and used as the anode in organic photovoltaic cells in concert with the conductive polymer, poly(3,4-ethylenedioxythiophene):poly(styrenesulfonate) (PEDOT:PSS). Compared to devices in which PEDOT:PSS alone serves as an anode, devices comprising grids of copper/nickel microwires and PEDOT:PSS exhibit lowered series resistance, which manifests in greater fill factor and power conversion efficiency. This simple method of forming micropatterns could find use in applications where cost and environmental impact should be minimized, especially as a potential replacement for the transparent electrode indium tin oxide (ITO) in thin-film electronics over large areas (i.e., solar cells) or as a method of rapid prototyping for laboratory-scale devices.

  9. Sustainability of abrasive processes

    DEFF Research Database (Denmark)

    Aurich, J.C.; Linke, B.; Hauschild, Michael Zwicky

    2013-01-01

    This paper presents an overview of research on sustainability of abrasive processes. It incorporates results from a round robin study on ‘‘energy-efficiency of abrasive processes’’ which has been carried out within the scientific technical committee ‘‘abrasive processes’’ (STC G) of CIRP, the con......This paper presents an overview of research on sustainability of abrasive processes. It incorporates results from a round robin study on ‘‘energy-efficiency of abrasive processes’’ which has been carried out within the scientific technical committee ‘‘abrasive processes’’ (STC G) of CIRP......, the content of technical presentations in STC G, and the results of a comprehensive literature study. The approach to sustainability includes environmental, social, and economic sustainability in accordance with the definition proposed in the Brundtland Report of the United Nations [156]. The main focus...... is on environmental and social sustainability. Economic sustainability will be considered as manufacturing productivity. © 2013 CIRP....

  10. Abrasion Properties of Steel Fiber Reinforced Silica Fume Concrete According to Los Angeles and Water Abrasion Tests

    Directory of Open Access Journals (Sweden)

    Tsan-Ching CHENG

    2014-12-01

    Full Text Available The current study mainly investigated the influence of different tests on the abrasion resistance of concrete mixed with steel fibers and silica fume. The abrasion resistance was assessed at 28, 56 and 91 days on concretes with water-binder ratios of 0.35 and 0.55 where in some mixes silica fume was substituted by 5 % of cement by weight. Steel fibers of 0.5 % and 1.0 % of concrete volume were also added into the test concrete by replacement of coarse and fine aggregates. The results showed that concrete with higher compressive strength in Los Angeles abrasion tests also had better abrasion resistance. The inclusion of steel fibers into test concrete with a water-binder ratio of 0.35 resulted in a significant increase in compressive strength. This concrete also displayed better abrasion resistance and splitting tensile strength than reference concrete; in the test sample with a water-binder ratio of 0.55, the added steel fibers was unable to effectively produce cementation with the concrete. The inclusion of silica fume improved the abrasion resistance of concretes. In water abrasion testing, the abrasion resistance of concrete containing steel fiber was worse than that of concrete without steel fibers. In the water abrasion testing, the surface of steel fiber reinforced concrete was eroded by water and steel balls, and the impact caused the steel fibers to separate from the concrete and led to higher wear loss. DOI: http://dx.doi.org/10.5755/j01.ms.20.4.6460

  11. Microabrasion: an epidermal abrasion.

    Science.gov (United States)

    Rubin, Mark G

    2003-03-01

    Microabrasion, which abrades the epidermis but does not extend into the dermis, is a mild level of injury that is useful in treating dull, rough texture; dyschromias; comedonal acne; keratosis pilaris; distensible acne scars; and fine lines. Results vary with the use of positive or negative pressure, choice of abrasive crystals, and operator technique. (Aesthetic Surg J 2003;23:137-139.).

  12. Abrasion of 6 dentifrices measured by vertical scanning interference microscopy

    Science.gov (United States)

    PASCARETTI-GRIZON, Florence; MABILLEAU, Guillaume; CHAPPARD, Daniel

    2013-01-01

    Objectives The abrasion of dentifrices is well recognized to eliminate the dental plaque. The aims of this study were to characterize the abrasive powders of 6 dentifrices (3 toothpastes and 3 toothpowders) and to measure the abrasion on a test surface by Vertical Scanning Interference microscopy (VSI). Material and Methods Bright field and polarization microscopy were used to identify the abrasive particles on the crude dentifrices and after prolonged washes. Scanning electron microscopy and microanalysis characterized the shape and nature of the particles. Standardized and polished blocks of poly(methylmethacrylate) were brushed with a commercial electric toothbrush with the dentifrices. VSI quantified the mean roughness (Ra) and illustrated in 3D the abraded areas. Results Toothpastes induced a limited abrasion. Toothpowders induced a significantly higher roughness linked to the size of the abrasive particles. One powder (Gencix® produced a high abrasion when used with a standard testing weight. However, the powder is based on pumice particles covered by a plant homogenate that readily dissolves in water. When used in the same volume, or after dispersion in water, Ra was markedly reduced. Conclusion Light and electron microscopy characterize the abrasive particles and VSI is a new tool allowing the analysis of large surface of abraded materials. PMID:24212995

  13. Abrasion of 6 dentifrices measured by vertical scanning interference microscopy.

    Science.gov (United States)

    Pascaretti-Grizon, Florence; Mabilleau, Guillaume; Chappard, Daniel

    2013-01-01

    The abrasion of dentifrices is well recognized to eliminate the dental plaque. The aims of this study were to characterize the abrasive powders of 6 dentifrices (3 toothpastes and 3 toothpowders) and to measure the abrasion on a test surface by Vertical Scanning Interference microscopy (VSI). Bright field and polarization microscopy were used to identify the abrasive particles on the crude dentifrices and after prolonged washes. Scanning electron microscopy and microanalysis characterized the shape and nature of the particles. Standardized and polished blocks of poly(methylmethacrylate) were brushed with a commercial electric toothbrush with the dentifrices. VSI quantified the mean roughness (Ra) and illustrated in 3D the abraded areas. Toothpastes induced a limited abrasion. Toothpowders induced a significantly higher roughness linked to the size of the abrasive particles. One powder (Gencix® produced a high abrasion when used with a standard testing weight. However, the powder is based on pumice particles covered by a plant homogenate that readily dissolves in water. When used in the same volume, or after dispersion in water, Ra was markedly reduced. Light and electron microscopy characterize the abrasive particles and VSI is a new tool allowing the analysis of large surface of abraded materials.

  14. Photoresist-Free Patterning by Mechanical Abrasion of Water-Soluble Lift-Off Resists and Bare Substrates: Toward Green Fabrication of Transparent Electrodes

    OpenAIRE

    Adam D Printz; Esther Chan; Celine Liong; René S Martinez; Lipomi, Darren J.

    2013-01-01

    This paper describes the fabrication of transparent electrodes based on grids of copper microwires using a non-photolithographic process. The process--"abrasion lithography"--takes two forms. In the first implementation (Method I), a water-soluble commodity polymer film is abraded with a sharp tool, coated with a conductive film, and developed by immersion in water. Water dissolves the polymer film and lifts off the conductive film in the unabraded areas. In the second implementation (Method ...

  15. LITERATURE SURVEY ON ABRASION PROBLEM IN CHENILLE YARNS

    Directory of Open Access Journals (Sweden)

    Erhan Kenan ÇEVEN

    2006-01-01

    Full Text Available Chenille yarns are traditionally used in the manufacture of furnishing fabrics, fashion knitwear, and as decorative threads in many types of broad and narrow fabrics. Chenille yarn has a very distinct weakness-it does not have very good inherent abrasion resistance. When the yarns are in use, clearly the abrasion resistance of the chenille yarn is crucially important. Either during further processing or during the eventual end-use, any removal of the effect yarn forming the beard will expose the ground yarns, which in turn will result in a bare appearance. To avoid this undesirable result, several options are available. Therefore, the studies on this area are about the investigation of the influences of some material types and machine parameters on the abrasion resistance of chenille yarns and fabrics produced with these yarns. In this paper, the experimental studies about the abrasion properties of chenille yarns in yarn, knitted and woven fabric forms are summarized.

  16. Qualitative Assessment of Wear Resistance and Surface Hardness of Different Commercially Available Dental Porcelain: An in vitro Study.

    Science.gov (United States)

    Singh, Abhishek; Nagpal, Abhishek; Pawah, Salil; Pathak, Chetan; Issar, Gaurav; Sharma, Pankaj

    2016-09-01

    In an attempt to minimize wear damage to the enamel of antagonist teeth, new low and medium fusing ceramic materials have been developed. Manufacturers usually claim that these ceramics are wear-friendly because of their lower hardness, lower concentrations of crystal phase, and smaller crystal sizes. This study aimed to quantitatively analyze the wear strength of various commercially available dental porcelain with tooth enamel as well as the surface hardness of these dental porcelain. The basic model was designed as a pin on plate arrangement. The tooth specimens were mounted on the stylus which was centered on the ceramic specimen in a wear testing machine. The dental ceramic specimen was centered in the metal die. A load of 40 N was applied at a rate of 80 cycles/minute for 15 minutes. In the current study, mean wear depth (Ra) value, volumetric loss, and surface hardness were obtained by standard quantification method and were statistically evaluated. Ceramco-3 was reported to be most abrasive for enamel; however, Duceram love significantly more abraded itself than the other two, Ceramco-3 and Vita Alpha, and generated the lowest loss of enamel. Also, same abrasive type of wear was revealed for all three variants of tested ceramics. Ceramco-3 was the most abrasive for enamel, while surface roughness (mean wear depth) of Duceram love was maximum and for Ceramco-3 it was minimum. The value of surface roughness for Vita Alpha was in between Duceram love and Ceramco-3. Nonetheless, the mean surface hardness of Duceram love was found to be least and maximum for Vita Alpha. In situations of dental wear and wasting tooth disease (Attrition/Abrasion), Duceram can be applied in lieu of Ceramco-3 so as to prevent worsening of existing dentition. However, in younger patients Vita Alpha would offer maximum durability due to its greater surface hardness.

  17. Anti-abrasive nanocoatings current and future applications

    CERN Document Server

    2015-01-01

    This book provides an overview of the fabrication methods for anti-abrasive nanocoatings. The connections among fabrication parameters, the characteristics of nanocoatings and the resulting properties (i.e. nanohardness, toughness, wear rate, load-bearing ability, friction coefficient, and scratch resistance) are discussed. Size-affected mechanical properties of nanocoatings are examined, including their uses. Anti-abrasive nanocoatings, including metallic-, ceramic-, and polymeric-based layers, as well as different kinds of nanostructures, such as multi-layered nanocomposites and thin films, are reviewed. * Provides a comprehensive overview of the fabrication methods for anti-abrasive nanocoatings* Discusses the connections among fabrication parameters, the characteristics of nanocoatings and the resulting properties* Reviews advantages and drawbacks of fabrication methods for anti-abrasive nanocoatings and clarifies the place of these nanocoatings in the world of nanotechnology

  18. Prepolishing on a CNC platform with bound abrasive contour tools

    Science.gov (United States)

    Schoeffler, Adrienne E.; Gregg, Leslie L.; Schoen, John M.; Fess, Edward M.; Hakiel, Michael; Jacobs, Stephen D.

    2003-05-01

    Deterministic microgrinding (DMG) of optical glasses and ceramics is the commercial manufacturing process of choice to shape glass surfaces prior to final finishing. This process employs rigid bound matrix diamond tooling resulting in surface roughness values of 3-5μm peak to valley and 100-400nm rms, as well as mid-spatial frequency tool marks that require subsequent removal in secondary finishing steps. The ability to pre-polish optical surfaces within the grinding platform would reduce final finishing process times. Bound abrasive contour wheels containing cerium oxide, alumina or zirconia abrasives were constructed with an epoxy matrix. The effects of abrasive type, composition, and erosion promoters were examined for tool hardness (Shore D), and tested with commercial optical glasses in an Optipro CNC grinding platform. Metrology protocols were developed to examine tool wear and subsequent surface roughness. Work is directed to demonstrating effective material removal, improved surface roughness and cutter mark removal.

  19. ESC resistance of commercial grade polycarbonates during exposure to butter and related chemicals

    DEFF Research Database (Denmark)

    Kjellander, Carina Koch; Nielsen, Tenna B; Ghanbari-Siahkali, Afshin

    2008-01-01

    Three commercial grades of polycarbonates (Lexan (R) 144, Lexan (R) 104 and Makrolon Rx1805) were studied with respect to resistance to environmental stress cracking (ESC) when exposed to butter and related chemicals. The polycarbonates (PCs) were extensively characterised to determine whether...

  20. Evaluation of pea accessions and commercial cultivars for Fusarium Root Rot resistance

    Science.gov (United States)

    Fusarium root rot caused by Fusarium solani f. sp. pisi (Fsp) can result in major yield losses in pea (Pisum sativum L.). Currently no fungicides effectively manage this disease. Previous studies evaluated the Pisum germplasm collection for resistance to Fsp, however, evaluations of commercial marke...

  1. Commercial sugar beet cultivars evaluated for rhizomania resistance and storability in Idaho, 2016

    Science.gov (United States)

    Rhizomania caused by Beet necrotic yellow vein virus (BNYVV) and storage losses are serious sugar beet production problems. To identify sugar beet cultivars with resistance to BNYVV and evaluate storability, 22 commercial cultivars were screened by growing them in a sugar beet field infested with B...

  2. Resistance towards persuasion: differences between non-profit and commercial advertising

    NARCIS (Netherlands)

    Boogaard, C.R.; Fransen, M.L.; Eisend, M.; Langner, T.

    2011-01-01

    In the present research we examined a variety of strategies that consumers may use to resist persuasion towards non-profit and commercial advertising. Based on research by Jacks and Cameron (2003), we investigated seven strategies (i.e., attitude bolstering, counter arguing, negative affect,

  3. Selection of loblolly pine varieties resistant to fusiform rust for commercial deployment

    Science.gov (United States)

    Andy Benowicz; Robert J. Weir

    2012-01-01

    Benowicz, Andy; Weir, Robert J. 2013. Selection of loblolly pine varieties resistant to fusiform rust for commercial deployment . In: Sniezko, Richard A.; Yanchuk, Alvin D.; Kliejunas, John T.; Palmieri, Katharine M.; Alexander, Janice M.; Frankel, Susan J., tech. coords. Proceedings of the fourth international workshop on the genetics of host-parasite interactions in...

  4. Effects of a Commercial Chitosan Formulation on Bark Beetle (Coleoptera: Curculionidae) Resistance Parameters in Loblolly Pine

    Science.gov (United States)

    K. D. Klepzig; B. L. Strom

    2011-01-01

    A commercially available chitosan product, Beyond™, was evaluated for its effects on loblolly pine, Pinus taeda L., responses believed related to bark beetle resistance. Treatments were applied 4 times at approx. 6-wk intervals between May and November 2008. Five treatments were evaluated: ground application (soil drench), foliar application, ground...

  5. Wear Resistance of Piston Sleeve Made of Layered Material Structure: MMC A356R, Anti-Abrasion Layer and FGM Interface

    Directory of Open Access Journals (Sweden)

    Hernik Szymon

    2016-09-01

    Full Text Available The aim of this paper is the numerical analysis of the one of main part of car engine – piston sleeve. The first example is for piston sleeve made of metal matrix composite (MMC A356R. The second improved material structure is layered. Both of them are comparison to the classical structure of piston sleeve made of Cr-Ni stainless steel. The layered material structure contains the anti-abrasion layer at the inner surface of piston sleeve, where the contact and friction is highest, FGM (functionally graded material interface and the layer of virgin material on the outer surface made of A356R. The complex thermo-elastic model with Archard's condition as a wear law is proposed. The piston sleeve is modelling as a thin walled cylindrical axisymmetric shell. The coupled between the formulation of thermo-elasticity of cylindrical axisymmetric shell and the Archard’s law with functionally changes of local hardness is proposed.

  6. Abrasives and possibilities of increase in efficiency of abrasive waterjets

    Czech Academy of Sciences Publication Activity Database

    Sitek, Libor; Martinec, Petr

    2016-01-01

    Roč. 9, March 2016 (2016), s. 877-881 ISSN 1805-0476 R&D Projects: GA MŠk(CZ) LO1406; GA MŠk ED2.1.00/03.0082 Institutional support: RVO:68145535 Keywords : high-speed waterjets * abrasive waterjets * abrasives * garnet * zirconia Subject RIV: JQ - Machines ; Tools http://www.mmscience.eu/content/file/archives/MM_Science_201603.pdf

  7. Corneal Sparing Conjunctival Abrasion

    Directory of Open Access Journals (Sweden)

    Hamid Ehsani-Nia

    2017-07-01

    Full Text Available History of present illness: A 15-year-old male was transported to the emergency department via ambulance as a trauma activation after being struck by an automobile while jogging. Patient was alert and oriented, with no focal neurological deficits and no loss of consciousness. The patient complained of right eye foreign body sensation. Significant findings: Physical exam was significant for multiple broken teeth, multiple minor abrasions on the face, and fine shards of shattered glass on his face and hair. His right eye had conjunctival injection, with no signs of subconjunctival hemorrhage or ocular penetration. Vision, extraocular movement, and pupillary exam were grossly intact. Fluorescein staining with slit lamp exam with cobalt blue filter examination of the right eye revealed superficial bulbar conjunctival uptake of fluorescein dye staining an area of the conjunctiva inferior to the limbus 5 mm vertical by 2 mm horizontal (estimation by photo provided. No foreign bodies were visualized in the inferior fornix. These findings were consistent with superficial conjunctival abrasion. The exam noted sparing of the corneal epithelium. Discussion: The conjunctiva is a thin, transparent membrane covering the ocular surface from the corneal limbus to the posterior eyelid margin.1 When damaged, the patient will classically have a “foreign body” sensation. It is important to identify the extent of the injury as not extending over the cornea, and also to search for lodged foreign bodies that damage the conjunctiva further with each blink. Classically retained foreign bodies will form a linear and vertical pattern of staining with fluorescein.2,3 Fluorescein stains expose basement membrane and fluoresces bright green under ultraviolet light, thus indicating areas of damage in contrast to its surrounding tissue.4,5 In the setting of acute trauma, urgent Ophthalmologic consultation is indicated if there is anterior chamber hemorrhage, a ruptured or

  8. Characterization of Postharvest Fungicide-Resistant Botrytis cinerea Isolates From Commercially Stored Apple Fruit.

    Science.gov (United States)

    Jurick, Wayne M; Macarisin, Otilia; Gaskins, Verneta L; Park, Eunhee; Yu, Jiujiang; Janisiewicz, Wojciech; Peter, Kari A

    2017-03-01

    Botrytis cinerea causes gray mold and is an economically important postharvest pathogen of fruit, vegetables, and ornamentals. Fludioxonil-sensitive B. cinerea isolates were collected in 2011 and 2013 from commercial storage in Pennsylvania. Eight isolates had values for effective concentrations for inhibiting 50% of mycelial growth of 0.0004 to 0.0038 μg/ml for fludioxonil and were dual resistant to pyrimethanil and thiabendazole. Resistance was generated in vitro, following exposure to a sublethal dose of fludioxonil, in seven of eight dual-resistant B. cinerea isolates. Three vigorously growing B. cinerea isolates with multiresistance to postharvest fungicides were further characterized and found to be osmosensitive and retained resistance in the absence of selection pressure. A representative multiresistant B. cinerea strain caused decay on apple fruit treated with postharvest fungicides, which confirmed the in vitro results. The R632I mutation in the Mrr1 gene, associated with fludioxonil resistance in B. cinerea, was not detected in multipostharvest fungicide-resistant B. cinerea isolates, suggesting that the fungus may be using additional mechanisms to mediate resistance. Results from this study show for the first time that B. cinerea with dual resistance to pyrimethanil and thiabendazole can also rapidly develop resistance to fludioxonil, which may pose control challenges in the packinghouse environment and during long-term storage.

  9. Plasma enhanced CVD of SiO{sub x}C{sub y}H{sub z} thin film on different textile fabrics: Influence of exposure time on the abrasion resistance and mechanical properties

    Energy Technology Data Exchange (ETDEWEB)

    Rosace, Giuseppe, E-mail: giuseppe.rosace@unibg.it [Dipartimento di Ingegneria Industriale, Universita degli Studi di Bergamo, viale Marconi, 5, 24044 Dalmine (Italy); Canton, Roberto [Moma srl, POINT, via Pasubio, 5, 24044 Dalmine (Italy); Colleoni, Claudio [Dipartimento di Ingegneria Industriale, Universita degli Studi di Bergamo, viale Marconi, 5, 24044 Dalmine (Italy)

    2010-02-01

    In order to improve textile fabric abrasion resistance, in this work a SiO{sub x}C{sub y}H{sub z} thin film was realized by low pressure plasma chemical vapour deposition (PCVD) at room temperature, using hexamethyldisiloxane (HMDSO) as precursor compound. To test changes in the performance properties of the surface finished samples as a function of the type of the substrate, the deposition was carried out on different textile fabrics. The polymerization processes were followed by weight measurements of textile fabrics. It was found that, after PCVD, a significantly lower fabric weight loss was observed on treated samples after rubbing than on the untreated samples. The morphology, elemental composition and type of chemical bonding present in the film applied on textile fabrics were also investigated using electron scanning microscopy (SEM), energy dispersive X-ray (EDX) and infrared spectroscopy techniques (FT-IR (ATR)). The results showed a substantial enhancement of wear resistance for the surfaces modified with the presented process, while tensile and tearing strength were adversely affected.

  10. Sandstone Turning by Abrasive Waterjet

    Czech Academy of Sciences Publication Activity Database

    Hlaváček, Petr; Cárach, J.; Hloch, Sergej; Vasilko, K.; Klichová, Dagmar; Klich, Jiří; Lehocká, D.

    2015-01-01

    Roč. 48, č. 6 (2015), s. 2489-2493 ISSN 0723-2632 R&D Projects: GA MŠk ED2.1.00/03.0082; GA MŠk(CZ) LO1406 Institutional support: RVO:68145535 Keywords : turning away from the jet * conventional turning towards the jet * sandstone * abrasive water jet Subject RIV: JQ - Machines ; Tools Impact factor: 2.386, year: 2015 http://www.springerprofessional.de/sandstone-turning-by-abrasive-waterjet/6038028.html

  11. Variation in resistance mechanisms to the green peach aphid among different Prunus persica commercial cultivars.

    Science.gov (United States)

    Verdugo, J A; Méndez, T; Ortiz-Martínez, S A; Cumsille, R; Ramírez, C C

    2012-10-01

    ABSTRACT Peaches and nectarines are frequently attacked by the green peach aphid Myzus persicae (Sulzer), with significant negative impacts on fruit production. The genetic variability of resistance to this aphid among commercial cultivars of Prunus persica (L.) Batsch and Prunus persica variety nectarina was evaluated in this study. In total, 16 cultivars of P. persica were selected to evaluate the occurrence and population growth rate of M. persicae in commercial orchards, as well as in no-choice and probing behavior laboratory assays. The results showed variability between cultivars in resistance and susceptibility to M. persicae, with three cultivars exhibiting different signatures of resistance. The peach cultivar 'Elegant Lady' exhibited a low occurrence of aphids in the orchard, a low rate of growth, moderate leaf-rejection in a no-choice test and a higher number and longer period of salivation into sieve elements, suggesting resistance at the phloematic level. The nectarine cultivar 'August Red' also exhibited low aphid occurrence in the orchard, a low rate of growth, and resistance at the prephloem and phloem levels. Finally, the nectarine 'July Red-NS92' exhibited a low occurrence of aphids in the orchard, a higher number of rejections in no-choice assays and no ingestion of phloem during the probing behavior experiments, suggesting prephloematic resistance. The rest of the cultivars studied exhibited clear susceptibility. Hence, different resistance mechanisms are apparent among the studied cultivars. The information gathered in this study regarding the resistance to M. persicae may assist breeding programs aimed at increasing aphid resistance to peaches and nectarines.

  12. Commercial agriculture and territorial resistance: Analysis of urban-rural relations in the province of Azuay

    Directory of Open Access Journals (Sweden)

    Nasser Rebai

    2013-09-01

    Full Text Available In the Ecuadorian province of Azuay, agro-ecology seems to signal towards the rebirth of family agriculture in a context of regional migration. Given changes in land usage and the improvement of peasant economies, we envisage a profound mutation in the rural landscape of Azuay. Notwithstanding, in lieu of a true model of territorial rural development, the term territorial resistance is used as weak regional commercial networks do not allow an adequate integration of a majority of peasants, evidencing the need for a more ambitious vision that takes into account the close ties between rural and urban areas, to assist the insertion of poor peasant farmers into commercial agriculture.

  13. Abrasive Wear Resistance of a Ti–Fe–Cr Alloy Obtained by Self-Propagating High-Temperature Synthesis and Modified with Boron and Carbon

    National Research Council Canada - National Science Library

    O. O. Onyshchuk

    2016-01-01

    ...–Cr system obtained by self-propagating hightemperature synthesis. It is shown that, as a result of the addition of carbon and boron, the heterogeneity of the structure and its wear resistance increase...

  14. Conduit Coating Abrasion Testing

    Science.gov (United States)

    Sullivan, Mary K.

    2013-01-01

    During my summer internship at NASA I have been working alongside the team members of the RESTORE project. Engineers working on the RESTORE project are creating ·a device that can go into space and service satellites that no longer work due to gas shortage or other technical difficulties. In order to complete the task of refueling the satellite a hose needs to be used and covered with a material that can withstand effects of space. The conduit coating abrasion test will help the researchers figure out what type of thermal coating to use on the hose that will be refueling the satellites. The objective of the project is to determine whether or not the conduit coating will withstand the effects of space. For the RESTORE project I will help with various aspects of the testing that needed to be done in order to determine which type of conduit should be used for refueling the satellite. During my time on the project I will be assisting with wiring a relay board that connected to the test set up by soldering, configuring wires and testing for continuity. Prior to the testing I will work on creating the testing site and help write the procedure for the test. The testing will take place over a span of two weeks and lead to an informative conclusion. Working alongside various RESTORE team members I will assist with the project's documentation and records. All in all, throughout my internship at NASA I hope to learn a number of valuable skills and be a part of a hard working team of engineers.

  15. Insect-resistant genetically modified rice in China: from research to commercialization.

    Science.gov (United States)

    Chen, Mao; Shelton, Anthony; Ye, Gong-yin

    2011-01-01

    From the first insect-resistant genetically modified (IRGM) rice transformation in 1989 in China to October 2009 when the Chinese Ministry of Agriculture issued biosafety certificates for commercial production of two cry1Ab/Ac Bacillus thuringiensis (Bt) lines, China made a great leap forward from IRGM rice basic research to potential commercialization of the world's first IRGM rice. Research has been conducted on developing IRGM rice, assessing its environmental and food safety impacts, and evaluating its socioeconomic consequences. Laboratory and field tests have confirmed that these two Bt rice lines can provide effective and economic control of the lepidopteran complex on rice with less risk to the environment than present practices. Commercializing these Bt plants, while developing other GM plants that address the broader complex of insects and other pests, will need to be done within a comprehensive integrated pest management program to ensure the food security of China and the world.

  16. Antimicrobial resistance in Salmonella and Escherichia coli isolated from commercial shell eggs.

    Science.gov (United States)

    Musgrove, M T; Jones, D R; Northcutt, J K; Cox, N A; Harrison, M A; Fedorka-Cray, P J; Ladely, S R

    2006-09-01

    The development of antimicrobial resistance in bacteria has become a global problem. Isolates of Salmonella and Escherichia coli recovered from shell egg samples, collected at 3 commercial plants, were analyzed for resistance to 16 antimicrobial agents (n=990). Eggs were sampled by rinsing in a saline solution. Pooled samples were preenriched in buffered peptone water and then selectively isolated using standard broths and agars. Salmonella-positive isolates were serogrouped immunologically before being serotyped. Enterobacteriaceae were enumerated from individual samples using violet red bile glucose agar plates. Escherichia coli were identified biochemically from presumptive Enterobacteriaceae isolates. Salmonella and generic E. coli antimicrobial-susceptibility testing was conducted using a semiautomated broth microdilution system. More resistance was observed in the Salmonella isolates (n=41) than in the E. coli isolates (n=194). Salmonella Typhimurium was the most prevalent (69.0%) serotype and demonstrated the greatest multiple resistance. Salmonella Kentucky, the least prevalent (5.0%) serotype recovered, was the most susceptible. Although 34.1% of the Salmonella serotypes were susceptible to all antimicrobial agents, 60.1% were resistant to 11 or more compounds. Many Salmonella isolates exhibited resistance to tetracycline (63.4%), nalidixic acid (63.4%), and streptomycin (61.0%). Most E. coli isolates (73.2%) were susceptible to all antimicrobial drugs. Many E. coli isolates exhibited resistance to tetracycline (29.9%), streptomycin (6.2%), and gentamicin (3.1%). Only 1% of the E. coli isolates were resistant to 4 antimicrobial agents. These data indicate that shell eggs can harbor resistant foodborne and commensal bacteria; among Salmonella isolates, resistance was serotype-dependent.

  17. Incidence of lameness and abrasions in piglets in identical farrowing pens with four different types of floor

    Directory of Open Access Journals (Sweden)

    Nilsson Ebba

    2009-05-01

    Full Text Available Abstract Background Lameness in piglets is a major animal welfare issue. Floor abrasiveness is a common cause of superficial injury in piglets in farrowing pens. The abrasion achieved may act as a gate for infections, which in turn may induce development of infectious arthritis. In this study, the influence of improvements of the floor quality and of increased ratios of straw in identical farrowing pens was measured. Methods The study was carried out at a herd with four identical farrowing units with solid concrete floor bedded with 1 kg chopped straw per sow and 1 hg per piglet and day. Nothing was changed in the management of the four identical farrowing units, but four experimental groups were created: Group I – control, Group II – the amount of bedding was doubled. The surface of the floor was repaired in two units, Group III – Piglet Floor®, Flowcrete Sweden AB, Perstorp, Sweden and Group IV – Thorocrete SL®, Växa Halland, Sweden. Three farrowing batches were studies in each unit. In total, 93 litters (1,073 piglets were examined for foot and skin lesions until the age of 3 weeks. The occurrence of lameness was registered until weaning at an average age of 4.5 weeks. Twenty seven lame piglets were culled instead of medicinally treated and subjected to necropsy including histopathological and microbiological examinations. Isolates of streptococci, staphylococci and E. coli were tested with respect to antimicrobial resistance. Results Piglet born on the repaired floors had the lowest prevalences of abrasions at carpus. Also the doubled straw ration decreased the abrasions. Skin lesions at carpus decreased significantly in magnitude in all four systems from day 10. At day 3, the sole bruising scores of the control unit were greater than the other three units (p Streptococcus dysgalactiae subsp. equisimilis (60%, Staphylococcus hyicus subsp. hyicus (35% and Escherichia coli (5%. These isolates were sensitive to all antibiotics

  18. Three body abrasion of laser surface alloyed aluminium AA1200

    CSIR Research Space (South Africa)

    Mabhali, Luyolo AB

    2012-06-01

    Full Text Available Laser surface alloying of aluminium AA1200 was performed with a 4 kW Nd:YAG laser to improve the abrasion wear resistance. Aluminium surfaces reinforced with metal matrix composites and intermetallic phases were achieved. The phases present depended...

  19. Resistance of Commercial Tomato Cultivars to Meloidogyne arenaria and M. incognita

    Directory of Open Access Journals (Sweden)

    Donggeun Kim

    2013-03-01

    Full Text Available Root-knot nematodes (Meloidogyne spp. are among the main pathogens of greenhouse crops worldwide.Plant resistance is currently the method of choice for controlling these pests. To select resistant tomato againsttwo common species of root-knot nematodes, M. incognita and M. arenaria, 36 commercial tomato(Lycopersicon esculentum Mill. cultivars were screened. Seventeen tomato cultivars were resistant to bothroot-knot nematodes: six in cherry tomato, ‘Tenten’, ‘Cadillac’, ‘Cutti’, ‘Sweet’, ‘Ppotto’, ‘Lycopin-9’, eightin globe tomato, ‘Lovely 240’, ‘Dotaerang Dia’, ‘Cupirang’, ‘Dotaerang Master’, ‘Super Dotaerang’,‘Dotaerang Season’, ‘Miroku’, ‘Hoyong’, and three in root stock, ‘Special’, ‘Fighting’, and ‘Magnet’.

  20. Resistance of Commercial Tomato Cultivars to Meloidogyne arenaria and M. incognita

    Directory of Open Access Journals (Sweden)

    Donggeun Kim

    2013-03-01

    Full Text Available Root-knot nematodes (Meloidogyne spp. are among the main pathogens of greenhouse crops worldwide. Plant resistance is currently the method of choice for controlling these pests. To select resistant tomato against two common species of root-knot nematodes, M. incognita and M. arenaria, 36 commercial tomato (Lycopersicon esculentum Mill. cultivars were screened. Seventeen tomato cultivars were resistant to both root-knot nematodes: six in cherry tomato, ‘Tenten’, ‘Cadillac’, ‘Cutti’, ‘Sweet’, ‘Ppotto’, ‘Lycopin-9’, eight in globe tomato, ‘Lovely 240’, ‘Dotaerang Dia’, ‘Cupirang’, ‘Dotaerang Master’, ‘Super Dotaerang’, ‘Dotaerang Season’, ‘Miroku’, ‘Hoyong’, and three in root stock, ‘Special’, ‘Fighting’, and ‘Magnet’.

  1. Optimization of Oxidation Temperature for Commercially Pure Titanium to Achieve Improved Corrosion Resistance

    Science.gov (United States)

    Bansal, Rajesh; Singh, J. K.; Singh, Vakil; Singh, D. D. N.; Das, Parimal

    2017-03-01

    Thermal oxidation of commercially pure titanium (cp-Ti) was carried out at different temperatures, ranging from 200 to 900 °C to achieve optimum corrosion resistance of the thermally treated surface in simulated body fluid. Scanning electron microscopy, x-ray diffraction, Raman spectroscopy and electrochemical impedance spectroscopy techniques were used to characterize the oxides and assess their protective properties exposed in the test electrolyte. Maximum resistance toward corrosion was observed for samples oxidized at 500 °C. This was attributed to the formation of a composite layer of oxides at this temperature comprising Ti2O3 (titanium sesquioxide), anatase and rutile phases of TiO2 on the surface of cp-Ti. Formation of an intact and pore-free oxide-substrate interface also improved its corrosion resistance.

  2. Analysis of Structure and Abrasion Resistance of the Metal Composite Based on an Intermetallic FeAl Phase with VC and TiC Precipitates

    Directory of Open Access Journals (Sweden)

    Kopyciński D.

    2013-09-01

    Full Text Available Metal alloys with matrix based on an Fe-Al system are generally considered materials for high-temperature applications. Their main advantages are compact crystallographic structure, long-range ordering and structural stability at high temperatures. These materials are based on an intermetallic phase of FeAl or Fe3Al, which is stable in the range from room temperature up to the melting point of 1240°C. Their application at high temperatures is also beneficial because of the low cost of production, very good resistance to oxidation and corrosion, and high mechanical strength. The casting alloy the structure of which includes the FeAl phase is, among others, highaluminium cast iron. This study has been devoted to the determination of the effect of vanadium and titanium on the transformation of the high-aluminium cast iron structure into an in-situ FeAl-VC composite.

  3. Cleaning power and abrasivity of a new toothpaste based on ion-exchange resins.

    Science.gov (United States)

    Torrado, Anna; Valiente, Manuel; Muñoz, Carlos A

    2004-04-01

    To compare the stain removal efficacy and enamel abrasivity of a new experimental dentifrice based on an ion-exchange resin mixture that releases calcium, fluoride, phosphate and zinc ions (named NMTD1), to four commercially available dentifrices: Crest Extra-whitening toothpaste, Crest Tartar Protection toothpaste, Crest Cavity Protection toothpaste and Colgate Fluoride Cavity Protection toothpaste. Calcium pyrophosphate was used as a control for the efficacy of the staining removal experiment. Cleaning power evaluation was made following the method developed by Stookey et al. The abrasion of the toothpastes was determined by means of a brushing machine, using 2000, 4000 and 8000 strokes and a 250g toothbrush load. Bovine specimens were prepared and abrasion was measured by a surface profilometer system. The new experimental dentifrice did not remove stains whereas Crest Extra-whitening and Crest Cavity Protection dentifrices produced statistically significant stain removal when compared with the calcium pyrophosphate control. Abrasion studies demonstrated that abrasion was linearly correlated to the number of strokes and the abrasion rates proved to be non significant for Colgate and the new experimental dentifrices, but significant for Crest Extra-whitening, Crest Tartar Protection and Crest Cavity Protection. This study demonstrated that the use of a dentifrice based on an ion-exchange mixture was not effective at removing stains and abrasion was most insignificant when compared to other commercially available toothpastes.

  4. Standard test method for conducting wet sand/rubber wheel abrasion tests

    CERN Document Server

    American Society for Testing and Materials. Philadelphia

    2002-01-01

    1.1 This test method covers laboratory procedures for determining the resistance of metallic materials to scratching abrasion by means of the wet sand/rubber wheel test. It is the intent of this procedure to provide data that will reproducibly rank materials in their resistance to scratching abrasion under a specified set of conditions. 1.2 Abrasion test results are reported as volume loss in cubic millimeters. Materials of higher abrasion resistance will have a lower volume loss. 1.3 The values stated in SI units are to be regarded as the standard. The values given in parentheses are for information only. This standard does not purport to address all of the safety concerns, if any, associated with its use. It is the responsibility of the user of this standard to establish appropriate safety and health practices and determine the applicability of regulatory limitations prior to use.

  5. Modeling of Micro Deval abrasion loss based on some rock properties

    Science.gov (United States)

    Capik, Mehmet; Yilmaz, Ali Osman

    2017-10-01

    Aggregate is one of the most widely used construction material. The quality of the aggregate is determined using some testing methods. Among these methods, the Micro Deval Abrasion Loss (MDAL) test is commonly used for the determination of the quality and the abrasion resistance of aggregate. The main objective of this study is to develop models for the prediction of MDAL from rock properties, including uniaxial compressive strength, Brazilian tensile strength, point load index, Schmidt rebound hardness, apparent porosity, void ratio Cerchar abrasivity index and Bohme abrasion test are examined. Additionally, the MDAL is modeled using simple regression analysis and multiple linear regression analysis based on the rock properties. The study shows that the MDAL decreases with the increase of uniaxial compressive strength, Brazilian tensile strength, point load index, Schmidt rebound hardness and Cerchar abrasivity index. It is also concluded that the MDAL increases with the increase of apparent porosity, void ratio and Bohme abrasion test. The modeling results show that the models based on Bohme abrasion test and L type Schmidt rebound hardness give the better forecasting performances for the MDAL. More models, including the uniaxial compressive strength, the apparent porosity and Cerchar abrasivity index, are developed for the rapid estimation of the MDAL of the rocks. The developed models were verified by statistical tests. Additionally, it can be stated that the proposed models can be used as a forecasting for aggregate quality.

  6. Whistle Abrasion: A Case Report.

    Science.gov (United States)

    Pereira, T; Shetty, S; Chande, M; Kamath, P

    2016-01-01

    Abrasion is the physical wearing of a tooth surface which can involve the presence of a foreign object repeatedly being in contact with the tooth. A 40-year-old male patient reported to our dental clinic with a 2-3 mm uneven gap between his upper and lower front teeth on occlusion. A detailed history revealed that he was a physical education teacher, and the habitual placement of the whistle for the last 15 years caused an indentation on the whistle which coincided with the abraded teeth. Conditions such as abrasion may need active restorations. A general dental practitioner should accurately identify the cause and treat the esthetic and functional impairment as required.

  7. Efecto del conteo de nódulos en la resistencia al desgaste por abrasión de los hierros dúctiles austemperados. // Effect of nodules count in the waste by abrasion resistance for ductile austempering irons.

    Directory of Open Access Journals (Sweden)

    C. J. Diez Cicero

    2004-05-01

    Full Text Available Entre los materiales metálicos de mayor demanda, la producción de hierro con grafito nodular, ocupa en la actualidad unode los lugares más importantes entre los hierros fundidos de alta resistencia, y con la introducción del tratamiento térmicode austemperado aplicado a estas fundiciones, se da lugar a una nueva familia de materiales, caracterizados por su altaresistencia mecánica y elevada tenacidad, que mantienen la economía y facilidad de producción de las fundicionesnodulares.Este trabajo, hace una valoración del comportamiento de hierros nodulares, con diferentes conteos de nódulos, a los que lesfue aplicado el tratamiento de austemperado y posteriormente se les sometió a ensayos de desgaste abrasivo.Con los resultados obtenidos se hace un análisis de la influencia del conteo de nódulos en dichas propiedades, así comotambién de la interrelación del conteo de nódulos con las variables de tratamiento térmico utilizadas en las muestrasensayadas.Palabras claves: Hierro nodular, conteo de nódulos, austemperado.____________________________________________________________________________Abstract.Between the metallic materials of greater demand, the iron production with nódular graphite occupies at the present time,one of the most important places between fused irons of high resistance, and with the introduction of the austempering heattreatment, applied to these meltings, brings a new family of materials, characterized by its high mechanical resistance andelevated tenacity, that maintain the economy and facility of production of the nodular smeltings.This work makes a valuation of the nodular irons behaviors, with different counts from nodules, to which the austemperingtreatment was applied, and later they were put under tests of abrasive wearing.Of the obtained results, takes control of the influence the nodules count in these properties, as well as, of the interrelation ofthe nodules count, with the used variables of heat

  8. Exposure to crystalline silica in abrasive blasting operations where silica and non-silica abrasives are used.

    Science.gov (United States)

    Radnoff, Diane L; Kutz, Michelle K

    2014-01-01

    Exposure to respirable crystalline silica is a hazard common to many industries in Alberta but particularly so in abrasive blasting. Alberta occupational health and safety legislation requires the consideration of silica substitutes when conducting abrasive blasting, where reasonably practicable. In this study, exposure to crystalline silica during abrasive blasting was evaluated when both silica and non-silica products were used. The crystalline silica content of non-silica abrasives was also measured. The facilities evaluated were preparing metal products for the application of coatings, so the substrate should not have had a significant contribution to worker exposure to crystalline silica. The occupational sampling results indicate that two-thirds of the workers assessed were potentially over-exposed to respirable crystalline silica. About one-third of the measurements over the exposure limit were at the work sites using silica substitutes at the time of the assessment. The use of the silica substitute, by itself, did not appear to have a large effect on the mean airborne exposure levels. There are a number of factors that may contribute to over-exposures, including the isolation of the blasting area, housekeeping, and inappropriate use of respiratory protective equipment. However, the non-silica abrasives themselves also contain silica. Bulk analysis results for non-silica abrasives commercially available in Alberta indicate that many contain crystalline silica above the legislated disclosure limit of 0.1% weight of silica per weight of product (w/w) and this information may not be accurately disclosed on the material safety data sheet for the product. The employer may still have to evaluate the potential for exposure to crystalline silica at their work site, even when silica substitutes are used. Limited tests on recycled non-silica abrasive indicated that the silica content had increased. Further study is required to evaluate the impact of product recycling

  9. Detection of methicillin-resistant Staphylococcus pseudintermedius with commercially available selective media.

    Science.gov (United States)

    Horstmann, C; Mueller, R S; Straubinger, R K; Werckenthin, C

    2012-01-01

    Commercially available selective media for methicillin-resistant Staphylococcus aureus (MRSA) were tested for the detection and isolation of methicillin-resistant Staphylococcus pseudintermedius (MRSP). Five different screening agars [mannitol salt agar with oxacillin and BD BBL™ Chromagar™ MRSA (BD Diagnostics); chromID™ MRSA agar (bioMérieux); Oxacillin resistance screening agar base (ORSAB); and Brilliance MRSA agar (Oxoid)] were analysed for the detection of MRSP. Bacteria that may be isolated together with MRSP and may grow on the screening agars were included in the study to determine possible interference with the growth of MRSP. MRSP grew well on all selective media except on BD BBL™ Chromagar™ MRSA (BD Diagnostics) and chromID™ MRSA agar (bioMérieux), on which a low to moderate growth rate was noted. ORSAB (Oxoid) and Brilliance MRSA agar (Oxoid) are most suitable for the detection and isolation of MRSP from clinical material. The importance of MRSP in veterinary medicine is increasing. Diagnostic systems are needed to detect MRSP carrier as soon as possible. This study provides information about selected MRSA screening agars for the detection of MRSP to the clinical microbiologists. © 2011 The Authors. Letters in Applied Microbiology © 2011 The Society for Applied Microbiology.

  10. On the abrasion of heat-treated 2.8C21Cr1Mo white cast iron

    Energy Technology Data Exchange (ETDEWEB)

    Al-Rubaie, Kassim S.; Preti, Orlando [Centro Universitario SOCIESC, Joinville (Brazil). Engenharia Mecanica; Pohl, Michael [Bochum Univ. (Germany). Inst. fuer Werkstoffe

    2016-09-15

    The abrasion behaviour of heat-treated 2.8C21Cr1Mo cast iron was studied. The specimens were destabilised at two temperatures, 980 and 1050 C, for 4 h, air hardened, and then tempered at five temperatures, 220, 320, 400, 500, and 620 C, for 2 h followed by air cooling. Using a pin-on-plate abrasion apparatus, the specimens were abraded on four types of bonded abrasives (silicon carbide, corundum, flint, and glass). The effect of work hardening on the abrasion resistance was investigated. It was found that the increase in alloy hardness produced by heat treatment had little effect on the abrasion resistance against silicon carbide or corundum; the inverse was true against flint or glass. The as-hardened structure containing 40% retained austenite gave the best abrasion resistance, whereas the hardened and tempered at 620 C showed the worst. Both bulk hardness and matrix hardness before wear correlated poorly with the abrasion resistance. Therefore, a general model ''equivalent hardness'' was developed, in which the hardness of the abraded matrix was considered. With this model, the abrasion behaviour can be clearly analysed.

  11. Effect of filler type on 3-body abrasion of dental composite

    Directory of Open Access Journals (Sweden)

    Yasini E.

    2005-06-01

    Full Text Available Statement of Problem: The relatively poor wear resistance of dental composite in stress bearing posterior situations has restricted wider clinical application of this restorative material. Purpose: The aim of this study was to evaluate the three body abrasive wear of a dental composite based on a new filler (leucite: KAl Si2O6 and to compare it with the wear resistance of a composite based on commonly used Aluminium – Barium Silicate filler. Materials and Methods: This research was an interventional study done in Iran polymer institute. Five specimens were considered in each group. All ceramic IPS Empress® (Ivoclar- Vivadent ingots based on leucite crystals were ball milled, passed through an 800 sieve and used as filler. Experimental composites were prepared by mixing the silane- treated fillers with monomers (BisGMA and TEGDMA. Camphorquinone and amine were used as photoinitiator system. Degree of conversion of the light-cured and post-cured composites was measured using FTIR spectroscopy. The prepared pastes were inserted into plexy-glass mold and light cured (700 mw/cm2, 40 s. Then for maximum degree of conversion specimens were post- cured (120ºC, 5 hours. Three body abrasion wear testing was performed using a wear machine with 50 rpm rotational movement. In this machine, pumice (150 meshes was used as the third body. Weight loss of specimens in each group was measured by balance after each 50 hours. After wear testing SEM examination was made specimens in each group. The data were analyzed and compared using ANOVA and Tukey HSD tests (P<0.05. Tetric Ceram was tested as commercial composite. Results: There were significantly differences between three body abrasive wear of composites. The ranking from lowest to highest was as follows: leucite composite (19% < Tetric Ceram (22% < glass composite (28%. leucite composite showed the highest wear resistance value, propably due to the crystalliniy and hardness of filler. Conclusion

  12. Recent Developments in Abrasive Hybrid Manufacturing Processes

    Directory of Open Access Journals (Sweden)

    Ruszaj Adam

    2017-06-01

    Full Text Available Recent dynamic development of abrasive hybrid manufacturing processes results from application of a new difficult for machining materials and improvement of technological indicators of manufacturing processes already applied in practice. This tendency also occurs in abrasive machining processes which are often supported by ultrasonic vibrations, electrochemical dissolution or by electrical discharges. In the paper we present the review of new results of investigations and new practical applications of Abrasive Electrodischarge (AEDM and Electrochemical (AECM Machining.

  13. Abrasion: A Common Dental Problem Revisited.

    Science.gov (United States)

    Milosevic, Alex

    2017-02-28

    Dental abrasion is most commonly seen at the cervical necks of teeth, but can occur in any area, even inter-dentally from vigorous and incorrect use of dental floss. Acid erosion has been implicated in the initiation and progress of the cervical lesion, while tooth-brush abrasion has long been held as the prime cause of cervical abrasion. Identification of the risk factors is clearly important in order to modify any habits and provide appropriate advice.

  14. Evaluation of abrasives in acne therapy.

    Science.gov (United States)

    Mills, O H; Kligman, A M

    1979-05-01

    Various abrasive materials, such as pumice, polyethylene, and aluminum oxide are widely used as adjuncts in the therapy of acne. The apparent rationale is that abrasion should unseat comedones and deter their formation. We assessed the efficacy of various abrasives and abradant pads. Varying degrees of peeling and erythema were produced, but there was no appreciable reduction of comedones. Aggravation was noted in some cases. Generally, the resorption of papules and pustules was enhanced.

  15. ABRASIVE ABSORPTION STUDY IN AWJ CUTTING

    Directory of Open Access Journals (Sweden)

    Bogdan BARABAŞ

    2016-11-01

    Full Text Available This paper studies the forming process of the hydro abrasive jet and the factors that determine its behaviour after leaving the nozzle until the moment of impact with the piece, in order to obtain an optimized configuration of the processing. The objectives are those of obtaining optimal surfaces in terms of quality, increased productivity and reduced costs. The paper specifies the model of the jet forming through air and abrasive absorption. The obtained results have confirmed the importance of exactly configuring the abrasive quantity in the jet through modifying the size of the abrasive grains and the attraction force required for their absorption.

  16. Refractory, Abrasive and Other Industrial Mineral Operations

    Data.gov (United States)

    Department of Homeland Security — This map layer includes refractory, abrasive, and other industrial minerals operations in the United States. The data represent commodities covered by the Minerals...

  17. Progress in abrasive and grinding technology

    CERN Document Server

    Xu, Xipeng

    2009-01-01

    The grinding and abrasive processing of materials are machining techniques which use bonded or loose abrasives to remove material from workpieces. Due to the well-known advantages of grinding and abrasive processes, advances in abrasive and grinding technology are always of great import in enhancing both productivity and component quality. In order to highlight the recent progress made in this field, the editor invited 21 world-wide contributions with the aim of gathering together all of the achievements of leading researchers into a single publication. The authors of the 21 invited papers, of

  18. Recent Developments in Abrasive Hybrid Manufacturing Processes

    National Research Council Canada - National Science Library

    Adam Ruszaj; Sebastian Skoczypiec; Dominik Wyszyński

    2017-01-01

    ... processes already applied in practice. This tendency also occurs in abrasive machining processes which are often supported by ultrasonic vibrations, electrochemical dissolution or by electrical discharges...

  19. Occurrence of transferable antibiotic resistances in commercialized ready-to-eat mealworms (Tenebrio molitor L.).

    Science.gov (United States)

    Osimani, Andrea; Cardinali, Federica; Aquilanti, Lucia; Garofalo, Cristiana; Roncolini, Andrea; Milanović, Vesna; Pasquini, Marina; Tavoletti, Stefano; Clementi, Francesca

    2017-12-18

    The present study aimed to assess the occurrence of transferable determinants conferring resistance to tetracyclines, macrolide-lincosamide-streptogramin B, vancomycin, beta-lactams, and aminoglycosides in 40 samples of commercialized edible mealworms (Tenebrio molitor L.) purchased from European Union (EU) and non-EU producers. A high prevalence of tet(K) was observed in all of the samples assayed, with percentages of PCR-based positivity that ranged from 80% (samples from Thailand) to 100% (samples from the Netherlands, Belgium and France). For macrolides, erm(B) prevailed, being detected in 57.5% of the samples assayed, whereas erm(A) and erm(C) were detected with lower frequencies. Genes for resistance to vancomycin were only detected in samples produced in France and Belgium, with 90% and 10% of the samples being positive for vanA, respectively. Beta-lactamase genes were found with low occurrence, whereas the gene aac-aph, conferring high resistance to aminoglycosides, was found in 40% of the samples produced in the Netherlands and Belgium and 20% of the samples produced in Thailand. The results of Principal Coordinate Analysis and Principal Component Analysis depicted a clean separation of the samples collected from the four producers based on the distribution of the 12 AR determinants considered. Given the growing interest on the use of mealworms as a novel protein source, AR detection frequencies found in the present study suggest further investigation into the use of antibiotics during rearing of this insect species and more extensive studies focused on the factors that can affect the diffusion of transferable ARs in the production chain. Until such studies are completed, prudent use of antibiotics during rearing of edible insects is recommended. Copyright © 2017 Elsevier B.V. All rights reserved.

  20. Whistle Abrasion: A Case Report

    OpenAIRE

    Pereira, T.; Shetty, S; Chande, M; Kamath, P.

    2016-01-01

    Abrasion is the physical wearing of a tooth surface which can involve the presence of a foreign object repeatedly being in contact with the tooth. A 40-year-old male patient reported to our dental clinic with a 2?3 mm uneven gap between his upper and lower front teeth on occlusion. A detailed history revealed that he was a physical education teacher, and the habitual placement of the whistle for the last 15 years caused an indentation on the whistle which coincided with the abraded teeth. Con...

  1. PROGRESS IN THERMO-ABRASIVE BLASTING SYSTEMS

    Directory of Open Access Journals (Sweden)

    I.A. Gorlach

    2012-01-01

    Full Text Available

    ENGLISH ABSTRACT: Quality of surface preparation of components and structures for further painting and/or coating is important in many fields of engineering. One of the most widely used methods of surface preparation is abrasive blasting. In the last few years, a new method for surface preparation has evolved, namely thermo-abrasive blasting. This technique utilises a high enthalpy thermal jet, generated by the thermo-abrasive blasting gun, to propel abrasive particles. Thermo-abrasive blasting has a number of advantages over conventional abrasive blasting, which were assessed during trials. This paper describes a progress in the applications of thermo-abrasive blasting as well as future potentials for South African industry. The performance data and economic comparison of conventional and thermo-abrasive blasting are also presented in this paper.

    AFRIKAANSE OPSOMMING: Die gehalte van voorbereiding van komponent- en struktuuroppervlaktes is oral belangrik in ingenieurswesetoepassings. Wat vrywel tot die hede dikwels gebruik was, is straalskuring. Onlangs het 'n nuwe metode tot stand gekom naamlik termostraalskuring. Die metode maak gebruik van 'n hoë entalpie termostaat om skuurmiddel aan te dryf. Die nuwe metode besit sekere voordele in vergelyking met tradisionele straalskuring. Praktykbevestiging is hiervan met toetse verkry. Hierdie stuk bespreek ook die praktyktoepassings van termostraalskuring en die gepaardgaande voordele vir die Suid-Afrikaanse nywerheid. Toepassingsdata en ekomiese vergelyking van konvensionele- en termostraalskuring word ook behandel.

  2. Performance Evaluation of Abrasive Grinding Wheel Formulated ...

    African Journals Online (AJOL)

    This paper presents a study on the formulation and manufacture of abrasive grinding wheel using locally formulated silicon carbide abrasive grains. Six local raw material substitutes were identified through pilot study and with the initial mix of the identified materials, a systematic search for an optimal formulation of silicon ...

  3. Experimental abrasion of pebbles I. Wet sandblasting

    NARCIS (Netherlands)

    Kuenen, Ph.H.

    1955-01-01

    Pebbles of various kinds were subjected to abrasion by a sand-laden current of water. The loss in weight resulting from the action of coarse and fine sand at different velocities was measured. There proved to be no abrasion below a velocity of 70 cm per second. At a bottom velocity of this amount

  4. Analysis of polymerization time on abrasive wear of dental resins

    Directory of Open Access Journals (Sweden)

    Eduardo Carlos Bianchi

    2010-03-01

    Full Text Available An evaluation was made of the abrasive wear of six composite thermofixed dental resins subjected to different polymerization times. The method of evaluation was based on sharpness measurements to quantify the abrasive wear resistance of the resins. To this end, a test bench was built, consisting of a rotating porcelain cylinder that wears out a resin-coated cylinder placed above it, thus causing vertical displacement of the contact as the wear progresses. The values of vertical displacement, i.e., the input variables, were read and recorded by means of a computer program to obtain the sharpness values. These data indicated that the resins displayed different behaviors as a function of the polymerization times applied, reinforcing the importance of using a practical and rapid method of analysis in order to ensure that the behavior of new materials is fully understood before they are launched on the market.

  5. Mechanical and three-body abrasive wear behaviour of PMMA/TPU blends

    Energy Technology Data Exchange (ETDEWEB)

    Poomali [Central Institute of Plastics Engineering and Technology, IDA, Phase-II, Cherlapally, Hyderabad 500051 (India); Siddaramaiah [Department of Polymer Science and Technology, SJ College of Engineering, Mysore 570006 (India); Suresha, B. [Department of Mechanical Engineering, National Institute of Engineering, Mysore 570008 (India)], E-mail: sureshab2004@yahoo.co.in; Lee, Joong-Hee [Bin Fusion Research Team, Department of Polymer and Nano Science and Technology, Chonbuk National University, Jeonju, Jeonbuk 561-756 (Korea, Republic of)

    2008-09-25

    The blends of poly(methyl methacrlate) (PMMA) and thermoplastic polyurethane (TPU) were prepared by a Brabender co-twin screw extruder. The mechanical and three-body abrasive wear behaviour of PMMA/TPU blends has been studied. Three-body abrasive wear tests were conducted using rubber wheel abrasion tester (RWAT) under different abrading distances at 200 rpm and 22 N load. A significant reduction in tensile strength and tensile modulus with an increase in TPU content in the blend formulation was observed. Three-body abrasive wear results indicate that the wear volume increases with increase in abrading distance for all the samples studied. However, neat PMMA showed better wear resistance as compared to PMMA/TPU blends. The worn surface features, as examined through scanning electron microscope (SEM), show matrix cracking and deep furrows in PMMA/TPU blends.

  6. Dynamic Mechanical Analysis and Three-Body Abrasive Wear Behaviour of Thermoplastic Copolyester Elastomer Composites

    Directory of Open Access Journals (Sweden)

    Hemanth Rajashekaraiah

    2014-01-01

    Full Text Available Various amounts of short fibers (glass and carbon and particulate fillers like polytetrafluoroethylene (PTFE, silicon carbide (SiC, and alumina (Al2O3 were systematically introduced into the thermoplastic copolyester elastomer (TCE matrix for reinforcement purpose. The mechanical properties such as storage modulus, loss modulus, and Tan δ by dynamic mechanical analysis (DMA and three-body abrasive wear performance on a dry sand rubber wheel abrasion tester have been investigated. For abrasive wear study, the experiments were planned according to L27 orthogonal array by considering three factors and three levels. The complex moduli for TCE hybrid composites were pushed to a higher level relative to the TCE filled PTFE composite. At lower temperatures (in the glassy region, the storage modulus increases with increase in wt.% of reinforcement (fiber + fillers and the value is maximum for the composite with 40 wt.% reinforcement. The loss modulus and damping peaks were also found to be higher by the incorporation of SiC and Al2O3 microfillers. The routine abrasive wear test results indicated that TCE filled PTFE composite exhibited better abrasion resistance. Improvements in the abrasion resistance, however, have not been achieved by short-fiber and particlaute filler reinforcements. From the Taguchi’s experimental findings, optimal combination of control factors were obtained for minimum wear volume and also predictive correlations were proposed. Further, the worn surface morphology of the samples was discussed.

  7. Use of commercial organic fertilizer increases the abundance of antibiotic resistance genes and antibiotics in soil.

    Science.gov (United States)

    Zhou, Xue; Qiao, Min; Wang, Feng-Hua; Zhu, Yong-Guan

    2017-01-01

    The application of manure-based commercial organic fertilizers (COFs) is becoming increasingly extensive because of the expanding market for organic food. The present study examined the effects of repeated applications of chicken or swine manure-based COFs on the fate of antibiotics and antibiotic resistance genes (ARGs) in soil by conducting a soil microcosm experiment. Application of COFs significantly increased antibiotics residues, as well as the relative abundance of ARGs and the integrase gene of class 1 integrons (intΙ1) in soil. Two months after each application, antibiotics and ARGs dissipated in amended soils, but they still remained at an elevated level, compared with the control. And, the accumulation of antibiotics was found due to repeated COF applications. However, the relative abundance of ARGs in most COF-amended soils did not differ significantly between the first application and the repeated application. The results imply that 2 months are not sufficient for ARGs to approach background levels, and that animal manure must be treated more effectively prior to using it in agriculture ecosystems.

  8. Effects of hybrid composition of LCP and glass fibres on abrasive ...

    Indian Academy of Sciences (India)

    Home; Journals; Bulletin of Materials Science; Volume 29; Issue 1. Effects of hybrid composition of ... The replacements of glass fibres with LCP fibres improved abrasive wear resistance of composite. The composite ... Incorporation of LCP fibre improved wear resistance of glass fibre reinforced LLDPE. Worn surfaces were ...

  9. A numerical and experimental study of oblique impact of ultra-high pressure abrasive water jet

    Directory of Open Access Journals (Sweden)

    Can Kang

    2016-03-01

    Full Text Available An investigation of the abrasive water jet with an emphasis on the oblique impact of abrasive particles on the target plate is performed. Ultra-high jet pressure necessitates a close examination of the phenomena featured by small spatial and temporal scales. The effect of oblique impact is assessed from both numerical and practical aspects. Numerical simulation, implemented using the commercial code LS-DYNA, allows a detailed inspection of transient stress wave propagation inside the target plate. And impact experiments facilitate a qualitative description of resultant footprints of oblique water jet. Different incident angles of abrasive particles are adopted and a comparison is thereby unfolded. The results indicate that rebound, embedding, and penetration of single abrasive particle are three representative final operation states. Adjacent to the abrasive particle, the response of the target plate to oblique impact is reflected by von Mises stress distribution and plate deformation as well. Oblique impact arouses non-symmetrical stress wave distributions and distinct unbalanced node displacements at the two sides of the abrasive particle. As for the target plate, global surface morphology is in accordance with predicted effects. The most favorable surface roughness is not associated with vertical impact, and it hinges upon the selection of standoff distance. Furthermore, variation of surface roughness with incident angle is not monotonous.

  10. Life cycle and sustainability of abrasive tools

    CERN Document Server

    Linke, Barbara

    2016-01-01

    This monograph focuses on abrasive tools for grinding, polishing, honing, and lapping operations. The book describes the life cycle of abrasive tools from raw material processing of abrasive grits and bonding, manufacturing of monolithic or multi-layered tools, tool use to tool end-of-life. Moreover, this work highlights sustainability challenges including economic, environmental, social and technological aspects. The target audience primarily comprises research and industry experts in the field of manufacturing, but the book may also be beneficial for graduate students.

  11. Mapping QTL affecting resistance to Marek's disease in an F6 advanced intercross population of commercial layer chickens.

    Science.gov (United States)

    Heifetz, Eliyahu M; Fulton, Janet E; O'Sullivan, Neil P; Arthur, James A; Cheng, Hans; Wang, Jing; Soller, Morris; Dekkers, Jack C M

    2009-01-14

    Marek's disease (MD) is a T-cell lymphoma of chickens caused by the Marek's disease virus (MDV), an oncogenic avian herpesvirus. MD is a major cause of economic loss to the poultry industry and the most serious and persistent infectious disease concern. A full-sib intercross population, consisting of five independent families was generated by crossing and repeated intercrossing of two partially inbred commercial White Leghorn layer lines known to differ in genetic resistance to MD. At the F6 generation, a total of 1615 chicks were produced (98 to 248 per family) and phenotyped for MD resistance measured as survival time in days after challenge with a very virulent plus (vv+) strain of MDV. QTL affecting MD resistance were identified by selective DNA pooling using a panel of 15 SNPs and 217 microsatellite markers. Since MHC blood type (BT) is known to affect MD resistance, a total of 18 independent pool pairs were constructed according to family x BT combination, with some combinations represented twice for technical reasons. Twenty-one QTL regions (QTLR) affecting post-challenge survival time were identified, distributed among 11 chromosomes (GGA1, 2, 3, 4, 5, 8, 9, 15, 18, 26 and Z), with about two-thirds of the MD resistance alleles derived from the more MD resistant parental line. Eight of the QTLR associated with MD resistance, were previously identified in a backcross (BC) mapping study with the same parental lines. Of these, 7 originated from the more resistant line, and one from the less resistant line. There was considerable evidence suggesting that MD resistance alleles tend to be recessive. The width of the QTLR for these QTL appeared to be reduced about two-fold in the F6 as compared to that found in the previous BC study. These results provide a firm basis for high-resolution linkage disequilibrium mapping and positional cloning of the resistance genes.

  12. Mapping QTL affecting resistance to Marek's disease in an F6 advanced intercross population of commercial layer chickens

    Directory of Open Access Journals (Sweden)

    Wang Jing

    2009-01-01

    Full Text Available Abstract Background Marek's disease (MD is a T-cell lymphoma of chickens caused by the Marek's disease virus (MDV, an oncogenic avian herpesvirus. MD is a major cause of economic loss to the poultry industry and the most serious and persistent infectious disease concern. A full-sib intercross population, consisting of five independent families was generated by crossing and repeated intercrossing of two partially inbred commercial White Leghorn layer lines known to differ in genetic resistance to MD. At the F6 generation, a total of 1615 chicks were produced (98 to 248 per family and phenotyped for MD resistance measured as survival time in days after challenge with a very virulent plus (vv+ strain of MDV. Results QTL affecting MD resistance were identified by selective DNA pooling using a panel of 15 SNPs and 217 microsatellite markers. Since MHC blood type (BT is known to affect MD resistance, a total of 18 independent pool pairs were constructed according to family × BT combination, with some combinations represented twice for technical reasons. Twenty-one QTL regions (QTLR affecting post-challenge survival time were identified, distributed among 11 chromosomes (GGA1, 2, 3, 4, 5, 8, 9, 15, 18, 26 and Z, with about two-thirds of the MD resistance alleles derived from the more MD resistant parental line. Eight of the QTLR associated with MD resistance, were previously identified in a backcross (BC mapping study with the same parental lines. Of these, 7 originated from the more resistant line, and one from the less resistant line. Conclusion There was considerable evidence suggesting that MD resistance alleles tend to be recessive. The width of the QTLR for these QTL appeared to be reduced about two-fold in the F6 as compared to that found in the previous BC study. These results provide a firm basis for high-resolution linkage disequilibrium mapping and positional cloning of the resistance genes.

  13. Frequency Of Isolation Of Salmonella From Commercial Poultry Feeds And Their Anti-Microbial Resistance Profiles, Imo State, Nigeria

    Directory of Open Access Journals (Sweden)

    Okoli IC

    2006-09-01

    Full Text Available This study was conducted to determine the frequency of isolation of salmonella and their microbial resistance profiles across different commercial poultry feeds sold in Imo State, Nigeria. Thirty-six bulk feed samples were colleted from 154 bag across different feed types and brands which included Guinea (GF, Top (TF, Vital (VF, Extra (EF, Animal care (AF and livestock (LF feeds. The salmonella isolated were tested against 14 anti-microbial drugs using the disc diffusion method. Bacterial load enumeration of the samples indicated a range of <30 colony forming unit (CFU to overgrowth at 104 serial dilutions. Eight feed samples (22.2% which cuts across the entire feed brands expect EF were positive for salmonella. The highest prevalence of 28.8% and 25.0% were recorded for LF and TF respectively, while VF, GF and AF had 11.1 and 10.0% respectively. Salmonella isolates showed high rates of resistance (51-100% against nitrofurantoin, ampicillin, tetracycline and ceftriazole, while moderate rates (31-50% were recorded for chloramphenicol, oxfloxacin and cotrimoxazole. Low resistance rates (1-30% were on the other hand recorded against ciprofloxacin and amoxycillin clavulanate (Augumentine, whereas zero resistance was demonstrated against pefloxacin, gentamycin, streptomycin and nalidixic. Commercial feeds form important channels for the dissemination of multi-drug resistant salmonella in Imo State, Nigeria.

  14. Incidence of lameness and abrasions in piglets in identical farrowing pens with four different types of floor

    Science.gov (United States)

    Zoric, Mate; Nilsson, Ebba; Lundeheim, Nils; Wallgren, Per

    2009-01-01

    Background Lameness in piglets is a major animal welfare issue. Floor abrasiveness is a common cause of superficial injury in piglets in farrowing pens. The abrasion achieved may act as a gate for infections, which in turn may induce development of infectious arthritis. In this study, the influence of improvements of the floor quality and of increased ratios of straw in identical farrowing pens was measured. Methods The study was carried out at a herd with four identical farrowing units with solid concrete floor bedded with 1 kg chopped straw per sow and 1 hg per piglet and day. Nothing was changed in the management of the four identical farrowing units, but four experimental groups were created: Group I – control, Group II – the amount of bedding was doubled. The surface of the floor was repaired in two units, Group III – Piglet Floor®, Flowcrete Sweden AB, Perstorp, Sweden and Group IV – Thorocrete SL®, Växa Halland, Sweden. Three farrowing batches were studies in each unit. In total, 93 litters (1,073 piglets) were examined for foot and skin lesions until the age of 3 weeks. The occurrence of lameness was registered until weaning at an average age of 4.5 weeks. Twenty seven lame piglets were culled instead of medicinally treated and subjected to necropsy including histopathological and microbiological examinations. Isolates of streptococci, staphylococci and E. coli were tested with respect to antimicrobial resistance. Results Piglet born on the repaired floors had the lowest prevalences of abrasions at carpus. Also the doubled straw ration decreased the abrasions. Skin lesions at carpus decreased significantly in magnitude in all four systems from day 10. At day 3, the sole bruising scores of the control unit were greater than the other three units (p < 0.001). At day 10 and 17, sole bruising was less common in the units with repaired floors than in the control group and the group with doubled straw ration. In total 41 piglets were diagnosed as lame

  15. Checking Out Cuts, Scratches, and Abrasions

    Science.gov (United States)

    ... and be sure that you have had a tetanus shot recently. Sometimes, a cut, scratch, or abrasion starts out as no big deal, but then gets infected. An infection (say: in-FEK-shun) happens when there are ...

  16. Metrological Aspects of Abrasive Tool Active Surface Topography Evaluation

    Directory of Open Access Journals (Sweden)

    Lipiński Dariusz

    2016-12-01

    Full Text Available Analysis of the shape and location of abrasive grain tips as well as their changes during the grinding process, is the basis for forecasting the machining process results. This paper presents a methodology of using the watershed segmentation in identifying abrasive grains on the abrasive tool active surface. Some abrasive grain tips were selected to minimize the errors of detecting many tips on a single abrasive grain. The abrasive grains, singled out as a result of the watershed segmentation, were then analyzed to determine their geometric parameters. Moreover, the statistical parameters describing their locations on the abrasive tool active surface and the parameters characterizing intergranular spaces were determined.

  17. Third abrasive wear mode: is it possible?

    Directory of Open Access Journals (Sweden)

    Ronaldo Câmara Cozza

    2014-04-01

    Full Text Available The objective of this paper is to propose an initial discussion on the characterization of a third abrasive wear mode. The results obtained in a previous work [1] under different test conditions revealed the occurrence of the superposition of the “rolling” and “grooving” abrasive wear modes. This phenomenon was denoted “micro-rolling abrasion” due to the observation that “rolling abrasion” was found to act on “grooving abrasion”.

  18. Propiedades mecánicas bajo compresión y resistencia al desgaste abrasivo de piezas gruesas de caucho acrilonitrilo/Thick section acrylonitrile rubber parts mechanical properties under compression and abrasive wear resistance/Propriedades mecânicas sob compressão e resistência ao desgaste abrasivo de peças grossas de borracha de acrilonitrilo

    National Research Council Canada - National Science Library

    Sandra Milena Velásquez-Restrepo; Diego Hernán Giraldo-Vásquez; Natalia Trinidad Zapata-Gallego

    2015-01-01

      In this work the mechanical properties variability under uniaxial compression and the abrasive wear through the cross section of thick-piece carbon-black reinforced acrylonitrile rubber (NBR) parts, was studied...

  19. [The application of air abrasion in dentistry].

    Science.gov (United States)

    Mandinić, Zoran; Vulićević, Zoran R; Beloica, Milos; Radović, Ivana; Mandić, Jelena; Carević, Momir; Tekić, Jasmina

    2014-01-01

    One of the main objectives of contemporary dentistry is to preserve healthy tooth structure by applying techniques of noninvasive treatment. Air abrasion is a minimally invasive nonmechanical technique of tooth preparation that uses kinetic energy to remove carious tooth structure. A powerful narrow stream of moving aluminum-oxide particles hit the tooth surface and they abrade it without heat, vibration or noise. Variables that affect speed of cutting include air pressure, particle size, powder flow, tip's size, angle and distance from the tooth. It has been proposed that air abrasion can be used to diagnose early occlusal-surface lesions and treat them with minimal tooth preparation using magnifier. Reported advantages of air abrasion include reduced noise, vibration and sensitivity. Air abrasion cavity preparations have more rounded internal contours than those prepared with straight burs. This may increase the longevity of placed restorations because it reduces the incidence of fractures and a consequence of decreased internal stresses. However, air abrasion cannot be used for all patients, i.e. in cases involving severe dust allergy, asthma, chronic obstructive lung disease, recent extraction or other oral surgery, open wounds, advanced periodontal disease, recent placement of orthodontic appliances and oral abrasions, or subgingival caries removal. Many of these conditions increase the risk of air embolism in the oral soft tissues. Dust control is a challenge, and it necessitates the use of rubber dam, high-volume evacuation, protective masks and safety eyewear for both the patient and the therapist.

  20. Commercial Dairy Cow Milk microRNAs Resist Digestion under Simulated Gastrointestinal Tract Conditions.

    Science.gov (United States)

    Benmoussa, Abderrahim; Lee, Chan Ho C; Laffont, Benoit; Savard, Patricia; Laugier, Jonathan; Boilard, Eric; Gilbert, Caroline; Fliss, Ismail; Provost, Patrick

    2016-11-01

    MicroRNAs are small, gene-regulatory noncoding RNA species present in large amounts in milk, where they seem to be protected against degradative conditions, presumably because of their association with exosomes. We monitored the relative stability of commercial dairy cow milk microRNAs during digestion and examined their associations with extracellular vesicles (EVs). We used a computer-controlled, in vitro, gastrointestinal model TNO intestinal model-1 (TIM-1) and analyzed, by quantitative polymerase chain reaction, the concentration of 2 microRNAs within gastrointestinal tract compartments at different points in time. EVs within TIM-1 digested and nondigested samples were studied by immunoblotting, dynamic light scattering, quantitative polymerase chain reaction, and density measurements. A large quantity of dairy milk Bos taurus microRNA-223 (bta-miR-223) and bta-miR-125b (∼10 9 -10 10 copies/300 mL milk) withstood digestion under simulated gastrointestinal tract conditions, with the stomach causing the most important decrease in microRNA amounts. A large quantity of these 2 microRNAs (∼10 8 -10 9 copies/300 mL milk) was detected in the upper small intestine compartments, which supports their potential bioaccessibility. A protocol optimized for the enrichment of dairy milk exosomes yielded a 100,000 × g pellet fraction that was positive for the exosomal markers tumor susceptibility gene-101 (TSG101), apoptosis-linked gene 2-interacting protein X (ALIX), and heat shock protein 70 (HSP70) and containing bta-miR-223 and bta-miR-125b. This approach, based on successive ultracentrifugation steps, also revealed the existence of ALIX - , HSP70 -/low , and TSG101 -/low EVs larger than exosomes and 2-6 times more enriched in bta-miR-223 and bta-miR-125b (P dairy cow milk contains numerous microRNAs that can resist digestion and are associated mostly with ALIX - , HSP70 -/low , and TSG101 -/low EVs. Our results support the existence of interspecies transfer of micro

  1. Identification of commercially available alloys for corrosion-resistant metallic reinforcement and test methods for evaluating corrosion-resistant reinforcement.

    Science.gov (United States)

    2008-01-01

    A literature review was conducted with the goal of identifying alternative low-cost corrosion-resistant steel reinforcement materials. The most promising alternate reinforcing materials seen to date that are less expensive than 300 series stainless s...

  2. HIV drug resistance testing among patients failing second line antiretroviral therapy. Comparison of in-house and commercial sequencing.

    Science.gov (United States)

    Chimukangara, Benjamin; Varyani, Bhavini; Shamu, Tinei; Mutsvangwa, Junior; Manasa, Justen; White, Elizabeth; Chimbetete, Cleophas; Luethy, Ruedi; Katzenstein, David

    2017-05-01

    HIV genotyping is often unavailable in low and middle-income countries due to infrastructure requirements and cost. We compared genotype resistance testing in patients with virologic failure, by amplification of HIV pol gene, followed by "in-house" sequencing and commercial sequencing. Remnant plasma samples from adults and children failing second-line ART were amplified and sequenced using in-house and commercial di-deoxysequencing, and analyzed in Harare, Zimbabwe and at Stanford, U.S.A, respectively. HIV drug resistance mutations were determined using the Stanford HIV drug resistance database. Twenty-six of 28 samples were amplified and 25 were successfully genotyped. Comparison of average percent nucleotide and amino acid identities between 23 pairs sequenced in both laboratories were 99.51 (±0.56) and 99.11 (±0.95), respectively. All pairs clustered together in phylogenetic analysis. Sequencing analysis identified 6/23 pairs with mutation discordances resulting in differences in phenotype, but these did not impact future regimens. The results demonstrate our ability to produce good quality drug resistance data in-house. Despite discordant mutations in some sequence pairs, the phenotypic predictions were not clinically significant. Copyright © 2016 Elsevier B.V. All rights reserved.

  3. Evaluation of Rheological Properties of Gel Abrasive in Magnetic Abrasive Finishing

    Directory of Open Access Journals (Sweden)

    A-Cheng Wang

    2013-01-01

    Full Text Available The purpose of this study was aimed at the evaluation of the mechanism of magnetic finishing with gel abrasive (MFGA, during which the performance of MFGA was compared to that of magnetic abrasive finishing (MAF. Of importance is that MFGA performs better than MAF based on the polishing-efficiency criterion. Silicone gels, however, are semisolid polymer gels with deforming properties that are temperature dependent, ultimately influencing significantly the polishing efficiency in MFGA. Therefore, taking as examples cylindrical rods which were polished using silicone gels with different plasticities to determine the corresponding temperatures of abrasive media in the working area, this study evaluated the MFGA mechanism to elucidate the properties of silicone gels and attain both the finished effect and effective gel abrasives in MFGA to produce a highly efficient polished surface. Next, circulating effects of abrasive media were identified to ensure the efficiency in MFGA and establish the relation between the concentrations of abrasive media and circulating effects in the working area. Experimental results show that silicone gels with low plasticity produce high temperature of abrasive media in MFGA; high temperature of abrasive medium makes excellent circulating effects in the working area, inducing high material removal and fine surface roughness.

  4. Determination of vibration frequency depending on abrasive mass flow rate during abrasive water jet cutting

    Czech Academy of Sciences Publication Activity Database

    Hreha, P.; Radvanská, A.; Hloch, Sergej; Peržel, V.; Krolczyk, G.; Monková, K.

    2014-01-01

    Roč. 77, 1-4 (2014), s. 763-774 ISSN 0268-3768 Institutional support: RVO:68145535 Keywords : Abrasive water jet * Abrasive mass flow rate * Vibration Subject RIV: JQ - Machines ; Tools Impact factor: 1.458, year: 2014 http://link.springer.com/article/10.1007%2Fs00170-014-6497-9#page-1

  5. Comparison between PEEK and Ti6Al4V concerning micro-scale abrasion wear on dental applications.

    Science.gov (United States)

    Sampaio, M; Buciumeanu, M; Henriques, B; Silva, F S; Souza, J C M; Gomes, J R

    2016-07-01

    In the oral cavity, abrasive wear is predictable at exposed tooth or restorative surfaces, during mastication and tooth brushing. Also, wear can occur at contacting surfaces between the Ti-based prosthetic structures and implants in presence of abrasive compounds from food or toothpaste. Thus, the aim of this work was to compare the abrasive wear resistance of PEEK and Ti6Al4V on three-body abrasion related to different hydrated silica content and loads. Surfaces of Ti6Al4V or PEEK cylinders (8mm diameter and 4mm height) were wet ground on SiC papers and then polished with 1µm diamond paste. After that, surfaces were ultrasonically cleaned in propyl alcohol for 15min and then in distilled water for 10min. Micro-scale abrasion tests were performed at 60rpm and on different normal loads (0.4, 0.8 or 1.2N) after 600 ball revolutions using suspensions with different weight contents of hydrated silica. After abrasive tests, wear scars on flat samples were measured to quantify the wear volume and characterized by scanning electron microscope (SEM) to identify the dominant wear mechanisms. Results showed a higher volume loss rate on PEEK than that recorded on Ti6Al4V,, when subjected to three-body abrasion tests involving hydrated silica suspensions. An increase in volume loss was noted on both tested materials when the abrasive content or load was increased. PEEK was characterized by less wear resistance than that on Ti6Al4V after micro-scale abrasion wear in contact with hydrated silica particles, as commonly found in toothpastes. Copyright © 2016 Elsevier Ltd. All rights reserved.

  6. Anthelmintic-resistant nematodes in Irish commercial sheep flocks- the state of play

    Directory of Open Access Journals (Sweden)

    Good Barbara

    2012-12-01

    Full Text Available Abstract Anthelmintic resistance has been reported in most sheep producing countries. Prior to the mid 1990s, reports of anthelmintic resistance in Ireland were sparse and focused on benzimidazole, one of the three classes of anthelmintic available during this period. This evidence for efficacy issues on Irish farms combined with awareness that anthelmintic resistance was increasingly being reported in other countries prompted the need for more comprehensive investigations on Irish farms. Faecal egg count reduction and micro-agar larval development tests were employed to investigate resistance to benzimidazole, levamisole and macrocyclic lactone. There is compelling evidence for resistance to both benzimidazole (>88% of flocks and levamisole (>39% of flocks. Resistance of nematode populations to macrocyclic lactone was suspected on a small number of farms (11% but needs to be confirmed. The recent introduction of two new classes of anthelmintics, after over a 25 year interval, together with the evidence that anthelmintic resistance is reported within a relatively short time following the introduction of a new anthelmintic compound means that the challenge to the industry is immediate. Actions are urgently required to manage anthelmintic resistance so as to prolong the lifespan of anthelmintics.

  7. Multidrug resistance in Enterococcus species of faecal origin from commercial dairy lactating cattle: Public health concern

    Directory of Open Access Journals (Sweden)

    Godfred Ngu Tanih

    2017-11-01

    Full Text Available Objective: To evaluate the prevalence of Enterococcus species in cattle faeces, their corresponding drug resistant patterns as well as the genes coding for resistance in the isolates. Methods: Two hundred and ninety rectal swabs were cultured for the isolation of Enterococcus. Presumptive isolates were confirmed by PCR, targeting the tuf gene, and confirmed isolates were identified to species level, using species-specific primers aimed at targeting six different species. Additionally, antibiogram was performed by disc diffusion and genes implicated in resistance were evaluated using molecular methods. Results: All presumptive isolates were confirmed as Enterococcus and speciated as: Enterococcus hirae (82%, Enterococcus faecium (5%, Enterococcus durans (5%, Enterococcus faecalis (2% and 6% of unidentified species. Resistance to various antimicrobials ranged from 16.4% for penicillin to 69.6% for erythromycin. Among the tetracycline and erythromycin-resistant isolates, tet M (100% and erm B (29% were the only amplified genes known to mediate resistance respectively. Other detected genes included van B (25%, van C1 (21% and bla Z (11%. Conclusions: A high prevalence of multidrug resistant Enterococcus species was observed in this study, accentuating the need to improve on animal farming practices to prevent the dissemination of this microorganism to the environment.

  8. Risk of Transmission of Antimicrobial Resistant Escherichia coli from Commercial Broiler and Free-Range Retail Chicken in India

    Science.gov (United States)

    Hussain, Arif; Shaik, Sabiha; Ranjan, Amit; Nandanwar, Nishant; Tiwari, Sumeet K.; Majid, Mohammad; Baddam, Ramani; Qureshi, Insaf A.; Semmler, Torsten; Wieler, Lothar H.; Islam, Mohammad A.; Chakravortty, Dipshikha; Ahmed, Niyaz

    2017-01-01

    Multidrug-resistant Escherichia coli infections are a growing public health concern. This study analyzed the possibility of contamination of commercial poultry meat (broiler and free-range) with pathogenic and or multi-resistant E. coli in retail chain poultry meat markets in India. We analyzed 168 E. coli isolates from broiler and free-range retail poultry (meat/ceca) sampled over a wide geographical area, for their antimicrobial sensitivity, phylogenetic groupings, virulence determinants, extended-spectrum-β-lactamase (ESBL) genotypes, fingerprinting by Enterobacterial Repetitive Intergenic Consensus (ERIC) PCR and genetic relatedness to human pathogenic E. coli using whole genome sequencing (WGS). The prevalence rates of ESBL producing E. coli among broiler chicken were: meat 46%; ceca 40%. Whereas, those for free range chicken were: meat 15%; ceca 30%. E. coli from broiler and free-range chicken exhibited varied prevalence rates for multi-drug resistance (meat 68%; ceca 64% and meat 8%; ceca 26%, respectively) and extraintestinal pathogenic E. coli (ExPEC) contamination (5 and 0%, respectively). WGS analysis confirmed two globally emergent human pathogenic lineages of E. coli, namely the ST131 (H30-Rx subclone) and ST117 among our poultry E. coli isolates. These results suggest that commercial poultry meat is not only an indirect public health risk by being a possible carrier of non-pathogenic multi-drug resistant (MDR)-E. coli, but could as well be the carrier of human E. coli pathotypes. Further, the free-range chicken appears to carry low risk of contamination with antimicrobial resistant and extraintestinal pathogenic E. coli (ExPEC). Overall, these observations reinforce the understanding that poultry meat in the retail chain could possibly be contaminated by MDR and/or pathogenic E. coli. PMID:29180984

  9. Risk of Transmission of Antimicrobial Resistant Escherichia coli from Commercial Broiler and Free-Range Retail Chicken in India.

    Science.gov (United States)

    Hussain, Arif; Shaik, Sabiha; Ranjan, Amit; Nandanwar, Nishant; Tiwari, Sumeet K; Majid, Mohammad; Baddam, Ramani; Qureshi, Insaf A; Semmler, Torsten; Wieler, Lothar H; Islam, Mohammad A; Chakravortty, Dipshikha; Ahmed, Niyaz

    2017-01-01

    Multidrug-resistant Escherichia coli infections are a growing public health concern. This study analyzed the possibility of contamination of commercial poultry meat (broiler and free-range) with pathogenic and or multi-resistant E. coli in retail chain poultry meat markets in India. We analyzed 168 E. coli isolates from broiler and free-range retail poultry (meat/ceca) sampled over a wide geographical area, for their antimicrobial sensitivity, phylogenetic groupings, virulence determinants, extended-spectrum-β-lactamase (ESBL) genotypes, fingerprinting by Enterobacterial Repetitive Intergenic Consensus (ERIC) PCR and genetic relatedness to human pathogenic E. coli using whole genome sequencing (WGS). The prevalence rates of ESBL producing E. coli among broiler chicken were: meat 46%; ceca 40%. Whereas, those for free range chicken were: meat 15%; ceca 30%. E. coli from broiler and free-range chicken exhibited varied prevalence rates for multi-drug resistance (meat 68%; ceca 64% and meat 8%; ceca 26%, respectively) and extraintestinal pathogenic E. coli (ExPEC) contamination (5 and 0%, respectively). WGS analysis confirmed two globally emergent human pathogenic lineages of E. coli, namely the ST131 (H30-Rx subclone) and ST117 among our poultry E. coli isolates. These results suggest that commercial poultry meat is not only an indirect public health risk by being a possible carrier of non-pathogenic multi-drug resistant (MDR)-E. coli, but could as well be the carrier of human E. coli pathotypes. Further, the free-range chicken appears to carry low risk of contamination with antimicrobial resistant and extraintestinal pathogenic E. coli (ExPEC). Overall, these observations reinforce the understanding that poultry meat in the retail chain could possibly be contaminated by MDR and/or pathogenic E. coli.

  10. Risk of Transmission of Antimicrobial Resistant Escherichia coli from Commercial Broiler and Free-Range Retail Chicken in India

    Directory of Open Access Journals (Sweden)

    Arif Hussain

    2017-11-01

    Full Text Available Multidrug-resistant Escherichia coli infections are a growing public health concern. This study analyzed the possibility of contamination of commercial poultry meat (broiler and free-range with pathogenic and or multi-resistant E. coli in retail chain poultry meat markets in India. We analyzed 168 E. coli isolates from broiler and free-range retail poultry (meat/ceca sampled over a wide geographical area, for their antimicrobial sensitivity, phylogenetic groupings, virulence determinants, extended-spectrum-β-lactamase (ESBL genotypes, fingerprinting by Enterobacterial Repetitive Intergenic Consensus (ERIC PCR and genetic relatedness to human pathogenic E. coli using whole genome sequencing (WGS. The prevalence rates of ESBL producing E. coli among broiler chicken were: meat 46%; ceca 40%. Whereas, those for free range chicken were: meat 15%; ceca 30%. E. coli from broiler and free-range chicken exhibited varied prevalence rates for multi-drug resistance (meat 68%; ceca 64% and meat 8%; ceca 26%, respectively and extraintestinal pathogenic E. coli (ExPEC contamination (5 and 0%, respectively. WGS analysis confirmed two globally emergent human pathogenic lineages of E. coli, namely the ST131 (H30-Rx subclone and ST117 among our poultry E. coli isolates. These results suggest that commercial poultry meat is not only an indirect public health risk by being a possible carrier of non-pathogenic multi-drug resistant (MDR-E. coli, but could as well be the carrier of human E. coli pathotypes. Further, the free-range chicken appears to carry low risk of contamination with antimicrobial resistant and extraintestinal pathogenic E. coli (ExPEC. Overall, these observations reinforce the understanding that poultry meat in the retail chain could possibly be contaminated by MDR and/or pathogenic E. coli.

  11. Cracking of porcelain surfaces arising from abrasive grinding with a dental air turbine.

    Science.gov (United States)

    Chang, Chee W; Waddell, J Neil; Lyons, Karl M; Swain, Michael V

    2011-12-01

    The purpose of this in vitro study was to evaluate porcelain cracking induced by abrasive grinding with a conventional dental air turbine and abrasive diamond burs. Four commercially available porcelains were examined-Wieland ALLUX, Wieland ZIROX, IPS e.max Ceram, and IPS Empress Esthetic Veneering porcelain. Sixty discs of each porcelain type were fabricated according to manufacturer instructions, followed by an auto-glaze cycle. Abrasive grinding using fine, extra-fine, and ultra-fine diamond burs was carried out, using a conventional dental air turbine. The grinding parameters were standardized with regard to the magnitude of the force applied, rotational speed of the diamond bur, and flow rate of the water coolant. A testing apparatus was used to control the magnitude of force applied during the grinding procedure. The ground surfaces were then examined under scanning electron microscope. Cracking was seen for all porcelain types when ground with the fine bur. Cracking was not seen for specimens ground with the extra-fine or the ultra-fine bur. Wet abrasive grinding with a conventional dental air turbine and fine grit diamond burs has the potential to cause cracking in the four porcelain types tested. Similar abrasive grinding with smaller grit size particles does not cause similar observable cracking. © 2011 by the American College of Prosthodontists.

  12. Effects of Load and Speed on Wear Rate of Abrasive Wear for 2014 Al Alloy

    Science.gov (United States)

    Odabas, D.

    2018-01-01

    In this paper, the effects of the normal load and sliding speed on wear rate of two-body abrasive wear for 2014 Al Alloy were investigated in detail. In order to understand the variation in wear behaviour with load and speed, wear tests were carried out at a sliding distance of 11 m, a speed of 0.36 m/s, a duration of 30 s and loads in the range 3-11 N using 220 grit abrasive paper, and at a speed range 0.09-0.90 m/s, a load of 5 N and an average sliding distance of 11 m using abrasive papers of 150 grit size under dry friction conditions. Before the wear tests, solution treatment of the 2014 Al alloy was carried out at temperatures of 505 and 520 °C for 1 h in a muffle furnace and then quenched in cold water at 15 °C. Later, the ageing treatment was carried out at 185 °C for 8 h in the furnace. Generally, wear rate due to time increased linearly and linear wear resistance decreased with increasing loads. However, the wear rate was directly proportional to the load up to a critical load of 7 N. After this load, the slope of the curves decreased because the excessive deformation of the worn surface and the instability of the abrasive grains began to increase. When the load on an abrasive grain reaches a critical value, the groove width is about 0.17 of the abrasive grain diameter, and the abrasive grains begin to fail. The wear rate due to time increased slightly as the sliding speed increased in the range 0.09-0.90 m/s. The reason for this is that changes arising from strain rate and friction heating are expected with increasing sliding speeds.

  13. Effect of abrasive particle size on friction and wear behaviour of various microstructures of 25CD4 steel

    Science.gov (United States)

    Trevisiol, C.; Jourani, A.; Bouvier, S.

    2017-05-01

    Many parameters, such as normal load and material bulk hardness, control the wear and friction behaviours of materials. Nonetheless, the investigation of the coupled contributions of microstructure and abrasive particle size are still lacking. A contribution is proposed by using steel pins with various microstructures with a similar macro-hardness (around 410HV) and chemical composition. A quenched martensitic microstructure, a tempered martensitic microstructure and three ferrite-martensite dual-phase microstructures, with a similar martensite volume fraction (around 67%) and different martensite colony morphologies, are established. Friction tests are performed between these pins and abrasive papers with different sizes ranging from 15μm to 200μm. Compared to single-phase microstructures (quenched and tempered martensitic microstructures) and whatever the abrasive particle size, ferrite-martensite dual-phase microstructures reduce the friction coefficient and provide better wear resistance. For the ferrite-martensite dual-phase microstructures and unlike fine and fibrous martensite colonies, coarse and granular martensite colonies minimize the friction coefficient. In addition, characterized by a change of wear mechanisms between abrasion and adhesion, an intermediate abrasive particle around 35 μm minimizes the friction coefficient. This study also reveals that the wear rate increases with the abrasive particle size which is associated to an increase of the attack angle of abrasive grains.

  14. The effect of microstructure on abrasive wear of steel

    Science.gov (United States)

    Kešner, A.; Chotëborský, R.; Linda, M.

    2017-09-01

    Abrasive wear of agricultural tools is one of the biggest problems in currently being. The amount of abrasive wear, depending on the microstructure, has been investigated in this work. Steels 25CrMo4 and 51CrV4 were used in this work to determine the effect of the microstructure on the abrasive wear. These steels are commonly used for components that have to withstand abrasive wear.SEM analysis was used to detect the microstructure. The standardized ASTM G65 method was used to compare the abrasive wear of steels. The results show that the abrasive wear depends on the microstructure of steels.

  15. Bulk density and soil resistance to penetration as affected by commercial thinning in northeastern Washington.

    Science.gov (United States)

    Johanna D. Landsberg; Richard E. Miller; Harry W. Anderson; Jeffrey S. Tepp

    2003-01-01

    Bulk density and soil resistance to penetration were measured in ten, 3- to 11-ha operational units in overstocked, mixed-conifer stands in northeast Washington. Resistance was measured with a recording penetrometer to the 33-cm depth (13 in) at 10 stations on each of 8 to 17, 30.5-m-long, randomly located transects in each unit. Subsequently, different combinations of...

  16. Multidrug resistance in Enterococcus species of faecal origin from commercial dairy lactating cattle: Public health concern

    OpenAIRE

    Godfred Ngu Tanih; Anthony Ifeanyin Okoh; Roland Ndip Ndip; Uchechukwu Uchechukwu Nwodo; Ezekiel Green

    2017-01-01

    Objective: To evaluate the prevalence of Enterococcus species in cattle faeces, their corresponding drug resistant patterns as well as the genes coding for resistance in the isolates. Methods: Two hundred and ninety rectal swabs were cultured for the isolation of Enterococcus. Presumptive isolates were confirmed by PCR, targeting the tuf gene, and confirmed isolates were identified to species level, using species-specific primers aimed at targeting six different species. Addit...

  17. Evaluation of commercial and experimental resist materials for use in MEBES mask making

    Science.gov (United States)

    Sauer, Charles A.; Dean, Robert L.; Morita, Etsuya; Tan, Zoilo C. H.; Smith, Bruce W.; Ewbank, Dale E.; Duttagupta, Sid P.; Rudack, Anne

    1995-12-01

    The SIA roadmap has identified CD control as a critical issue in mask making. PBS, the most popular resist used for electron-beam mask making in the U.S., may not perform at the level required for production of 250 nm devices. There is a need in the industry today for precise CD control and tight control of CD uniformity, as well as a desire to dry etch thin films on masks. These industry trends make the use of an alternative resist attractive. A project was initiated to determine if an acceptable substitute to PBS exists. A group of eleven negative and positive resists were examined. These included chemically amplified materials, two part- novolacs, and a silicon-containing resist, among others. The resists were evaluated by using design of experiments (DOE) methodology whenever possible. All masks were exposed on 10 kV MEBES writing tools. The results were tabulated and compared, using a SEMATECH criterion for acceptability. Results are presented, including optimization of some of the materials for sensitivity, process robustness, and dry etch capability. While none of the materials met all criteria, several resists performed at a level that make them candidates to replace PBS. Several options are presented that are of interest to the mask maker contemplating process changes to accommodate 250 nm and 180 nm technologies.

  18. Basics of cutting and abrasive processes

    CERN Document Server

    Toenshoff, Hans Kurt

    2013-01-01

    Manufacturing is the basic industrial activity generating real value. Cutting and abrasive technologies are the backbone of precision production in machine, automotive and aircraft building as well as of production of consumer goods. We present the knowledge of modern manufacturing in these technologies on the basis of scientific research. The theory of cutting and abrasive processes and the knowledge about their application in industrial practice are a prerequisite for the studies of manufacturing science and an important part of the curriculum of the master study in German mechanical engineering. The basis of this book is our lecture “Basics of cutting and abrasive processes” (4 semester hours/3 credit hours) at the Leibniz University Hannover, which we offer to the diploma and master students specializing in manufacturing science.

  19. The application of air abrasion in dentistry

    Directory of Open Access Journals (Sweden)

    Mandinić Zoran

    2014-01-01

    Full Text Available One of the main objectives of contemporary dentistry is to preserve healthy tooth structure by applying techniques of noninvasive treatment. Air abrasion is a minimally invasive nonmechanical technique of tooth preparation that uses kinetic energy to remove carious tooth structure. A powerful narrow stream of moving aluminum-oxide particles hit the tooth surface and they abrade it without heat, vibration or noise. Variables that affect speed of cutting include air pressure, particle size, powder flow, tip’s size, angle and distance from the tooth. It has been proposed that air abrasion can be used to diagnose early occlusal-surface lesions and treat them with minimal tooth preparation using magnifier. Reported advantages of air abrasion include reduced noise, vibration and sensitivity. Air abrasion cavity preparations have more rounded internal contours than those prepared with straight burs. This may increase the longevity of placed restorations because it reduces the incidence of fractures and a consequence of decreased internal stresses. However, air abrasion cannot be used for all patients, i.e. in cases involving severe dust allergy, asthma, chronic obstructive lung disease, recent extraction or other oral surgery, open wounds, advanced periodontal disease, recent placement of orthodontic appliances and oral abrasions, or subgingival caries removal. Many of these conditions increase the risk of air embolism in the oral soft tissues. Dust control is a challenge, and it necessitates the use of rubber dam, high-volume evacuation, protective masks and safety eyewear for both the patient and the therapist. [Projekat Ministarstva nauke Republike Srbije, br. 46009

  20. Evolution and diagnostic utility of aeolian rat-tails: A new type of abrasion feature on Earth and Mars

    Science.gov (United States)

    Favaro, Elena A.; Hugenholtz, Christopher H.; Barchyn, Thomas E.

    2017-10-01

    Aeolian rat-tails (ARTs) are a previously undocumented, regionally-ubiquitous aeolian abrasion feature observed on matrix-supported ignimbrite surfaces in the Puna Plateau of Northwest Argentina. ARTs consist of an abrasion-resistant lithic clast projecting above the surface with a lee tail or 'keel' in the more erodible matrix. Size is controlled by the dimensions of the windward lithic clast, ranging from centimetre to meter scale; spatial density varies with clast content, which may reflect variations in ignimbrite facies. Field observations suggest ARTs follow a definable evolutionary sequence. First, an abrasion-resistant lithic clast contained within the ignimbrite is exposed to abrasion at the surface. Impacts from abrading particles erode the softer ignimbrite matrix adjacent to the clast. The clast shelters the leeward surface under a unimodal abrasion direction, creating a tail that tapers downwind and elongates as the clast emerges. Clasts become dislodged from the matrix as the surrounding surface erodes, ultimately destroying the feature if the clast is small enough to be mobilized directly by wind or impacting particles. This evolutionary sequence explains the morphology of ARTs and the presence of loose clasts on the ignimbrite surface, which contributes to the development of other landforms in the region, such as periodic bedrock ridges, yardangs, and megaripples. Satellite and rover images suggest similar features also exist on Mars. Because the formation and preservation of ARTs is contingent on unimodal abrasion direction, their orientation can be used as an indicator of long-term aeolian sediment transport direction.

  1. In vitro fracture resistance of three commercially available zirconia crowns for primary molars.

    Science.gov (United States)

    Townsend, Janice A; Knoell, Patrick; Yu, Qingzhao; Zhang, Jian-Feng; Wang, Yapin; Zhu, Han; Beattie, Sean; Xu, Xiaoming

    2014-01-01

    The purpose of this study was to measure the fracture resistance of primary mandibular first molar zirconia crowns from three different manufacturers-EZ Pedo (EZP), NuSmile (NSZ), and Kinder Krowns (KK)-and compare it with the thickness of the zirconia crowns and the measured fracture resistance of preveneered stainless steel crowns (SSCs). The thickness of 20 zirconia crowns from three manufacturers were measured. The mean force required to fracture the crowns was determined. Preveneered NuSmile (NSW) SSCs were tested as a control. EZP crowns were significantly thicker in three of the six measured locations. The force required to fracture the EZP crown was significantly higher than that required for NSZ and KK. There was a positive correlation between fracture resistance and crown thickness in the mesial, distal, mesioocclusal, and distoocclusal dimensions. None of the zirconia crowns proved to be as resistant to fracture as the preveneered SSCs. Statistically significant differences were found among the forces required to fracture zirconia crowns by three different manufacturers. The increase in force correlated with crown thickness. The forces required to fracture the preveneered stainless steel crowns were greater than the forces required to fracture all manufacturers' zirconia crowns.

  2. Screening for Resistance to Downy Mildew among Major Commercial Cucumber Varieties

    Directory of Open Access Journals (Sweden)

    Jung-Sup Lee

    2013-09-01

    Full Text Available This study was carried out for the downy mildew resistant test between 2010 and 2012. A set of 22 accessions belonging to 2 wild species and 20 varieties of the genus Cucumis, originating mainly from the Asian Vegetable Research and Development Center (AVRDC Gene Centre, was evaluated for resistance to Pseudoperonospora cubensis, causal agent of cucumber downy mildew. The youngest fully expanded true leaves were found suitable for in vitro screening. Both leaf discs and full leaves could be kept fresh longer when applying 0.2 μg/ml of gibberellin acid (GA. The incubation temperature of 20oC was found to be the most suitable temperature for symptom development comparing with 15 and 25oC. Symptom development was faster when contact diseased leaf discs (2 weeks after inoculation on to fresh leaf samples comparing with using conidia suspension (105 spores/ml. The numbers of spots in ‘C-19’ were lower than other varieties. ‘C-19’ variety was also showed the highest level of downy mildew resistant at 20oC chamber in 6 days after inoculating with pathogen and displayed 0.90 (under 10% of the infected rate. However, other varieties displayed susceptible in the pathogen sprayed plots. ‘C-19’ was the most resistant variety and no lesion was observed. Based on all data, ‘C-19’ can be a useful variety for the prevention of downy mildew.

  3. Multi-Year Evaluation of Commercial Soybean Cultivars for Resistance to Phytophthora sojae

    Science.gov (United States)

    Phytophthora sojae causes damping off, root rot, and stem rot of soybean, particularly in poorly drained soils. The use of resistance has been one of the primary management tools used to control this disease, with the most commonly used genes being Rps1c and Rps1k, followed by Rps1a. The Varietal In...

  4. Performance Enhancement of Abrasive Waterjet Cutting

    NARCIS (Netherlands)

    Karpuschewski, B.

    Abrasive Waterjet (AWJ) Machining is a recent non-traditional machining process. This technology is widely used in industry for cutting difficult-to-machine-materials, milling slots, polishing hard materials etc. AWJ machining has many advantages, e.g. it can cut net-shape parts, no heat is

  5. Opportunities in Abrasive Water Jet Machining

    NARCIS (Netherlands)

    Hoogstrate, A.M.; Karpuschewski, B.; van Luttervelt, C.A.; Meijer, J.; Kals, H.J.J.

    1997-01-01

    In the recent years the interest in loose abrasive machining processes as efficient, flexible processes is rising. This paper describes the development of a ‘coherent set of models’ for a category of these processes, namely those which use high velocity of the particles to obtain the necessary

  6. Performance Enhancement of Abrasive Waterjet Cutting

    NARCIS (Netherlands)

    2008-01-01

    Abrasive Waterjet (AWJ) Machining is a recent non-traditional machining process. This technology is widely used in industry for cutting difficult-to-machine-materials, milling slots, polishing hard materials etc. AWJ machining has many advantages, e.g. it can cut net-shape parts, no heat is

  7. Assessment of mechanical and three-body abrasive wear peculiarity ...

    Indian Academy of Sciences (India)

    The three-body abrasive wear characteristic of fabricated composites has been assessed under different operating conditions. For this, the three-body abrasion test is done on dry abrasion test rig (TR-50)and analysed using Taguchi's experimental design scheme and analysis of variance. The results obtained from these ...

  8. 29 CFR 1910.215 - Abrasive wheel machinery.

    Science.gov (United States)

    2010-07-01

    ... 29 Labor 5 2010-07-01 2010-07-01 false Abrasive wheel machinery. 1910.215 Section 1910.215 Labor... OCCUPATIONAL SAFETY AND HEALTH STANDARDS Machinery and Machine Guarding § 1910.215 Abrasive wheel machinery. (a) General requirements—(1) Machine guarding. Abrasive wheels shall be used only on machines provided with...

  9. Dust transport and abrasion assessment within simulated standing vegetation

    Science.gov (United States)

    Crop residues are useful in protecting the top soil from depletion and abrasion due to wind erosion. A wind tunnel study was done to measure sand transport and abrasion energies within the simulated artificial standing vegetation. Wind profiles, relative abrasion energies and rates of sand dischar...

  10. Antibacterial resistance of Enterococcus spp. isolated from commercial poultry of the Russian Federation farms in 2013–2016, and identification of vancomycin resistance genes

    Directory of Open Access Journals (Sweden)

    E. A. Svetoch

    2017-01-01

    Full Text Available Rationale: Enterococci are the leading cause of a number of nosocomial and community-acquired human diseases. In the last decade, these pathogens are becoming resistant to antibacterials, including vancomycin. Multidrug-resistant enterococci have been also isolated from agricultural animals in many countries worldwide, which raises concern of scientists because of possible horizontal transfer of resistance genes. Aim: To assess antibacterial sensitivity of Enterococcus spp. isolates collected from the poultry in the Russian Federation from 2013 to 2016, and to identify vancomycin-resistance genes in their genomes. Materials and methods: Eightyseven enterococci isolates belonging to E.  faecalis (n=47, 54%, E.  faecium (n=25, 28.7% and other species (n=15, 17.2% were collected from clinical samples of 297 heads of poultry (liver, lungs, heart, spleen, contents of the nasal and sinus cavities from 17  poultry farms of the Northwest, Central, Volga, Ural and Southern Federal districts of the Russian Federation. Sensitivity of enterococci to antibacterials was determined by disk-diffusion and broth microdilution methods. Vancomycin resistance genes van was detected by polymerase chain reaction with specific primers. Results: Most enterococci isolates were resistant to erythromycin (74/87, 85.1%, gentamicin (70/87, 80.5%, ceftriaxone (61/87, 70.1%, ciprofloxacin (56/87, 64.4%, tetracycline (57/87, 65.5%, and rifampicin (48/87, 55.2%, fewer ones to trimethoprim (38/87, 43.7%, ampicillin (28/87, 32.2%, linezolid (15/87, 17.2% and chloramphenicol (5/87, 5.7%. The vanC type genes (vanC1 and vanC2/3 were identified in 10  isolates. Vancomycin minimal inhibitory concentrations for these isolates were 2 to 8  mg/L. E. faecium with vanC1 gene was isolated from poultry probably for the first time ever. Conclusion: Commercial poultry in the Russian poultry farms is an important reservoir and source of antibiotic-resistant enterococci populations

  11. Wear resistance of a modified polymethyl methacrylate artificial tooth compared to five commercially available artificial tooth materials.

    Science.gov (United States)

    Kamonwanon, Pranithida; Yodmongkol, Sirasa; Chantarachindawong, Rojcharin; Thaweeboon, Sroisiri; Thaweeboon, Boonyanit; Srikhirin, Toemsak

    2015-08-01

    Wear resistance is a limitation of artificial denture teeth. Improving the wear resistance of conventional artificial denture teeth is of value to prosthodontic patients. The purpose of this in vitro study was to evaluate the wear resistance and hardness of modified polymethyl methacrylate artificial denture teeth compared to 5 commercially available artificial tooth materials. This study evaluated 180 artificial denture teeth (6 groups) that included 3 groups of conventional artificial teeth (MajorDent, Cosmo HXL, and Gnathostar), 2 groups of composite resin artificial teeth (Endura and SR Orthosit PE), and 1 group of modified surface artificial teeth. The flattened buccal surface of each tooth (n=15) was prepared for investigation with the Vickers hardness test and the elucidate wear test (n=15) by using a brushing machine. Each group was loaded for 18,000 cycles, at 2 N, and 150 rpm. The wear value was identified with a profilometer. The data were statistically analyzed by using 1-way ANOVA and post hoc Turkey honestly significant difference tests (α=.001). The tribologies were observed under a scanning electron microscope, and the cytotoxicities were evaluated by MTT assay. The Vickers hardnesses ranged from 28.48 to 39.36. The wear depths and worn surface area values ranged from 1.12 to 10.79 μm and from 6.74 to 161.95 μm(2). The data revealed that the modified artificial denture teeth were significantly harder and exhibited significantly higher wear resistance than did the conventional artificial teeth (Pmaterial. Within the limitations of this study, the polymethyl methacrylate modified surface artificial denture teeth was not significantly different from that of the composite resin artificial denture teeth, with the exceptions that the surface was harder and more wear resistant. Copyright © 2015 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

  12. Boric Acid and Commercial Organoboron Products as Inhibitors of Drug-Resistant Candida albicans.

    Science.gov (United States)

    Larsen, Bryan; Petrovic, Marija; De Seta, Francesco

    2017-10-09

    Clinical use of boric acid as a topical antifungal in women who have failed standard antifungal therapy with azole drugs has been used sporadically for decades. Our previous in vitro work showing inhibition of Candida albicans growth was conducted on clinical isolates without antifungal drug susceptibility profiling. Here, we report that boric acid restricts growth of drug-resistant Candida albicans and inhibits hyphal growth and diminishes cell volume. The availability of over-the-counter organoboron compounds intended for use as oral nutritional supplements led us to determine if these also were inhibitory toward resistant Candida and show here that they also possess antifungal activity. Candida glabrata was also found to be inhibited by boric acid and organoboron compounds. Further development of organoboron compounds as topical therapeutics is of potential value.

  13. Shrinkage, abrasion, erosion and sorption of clay plasters

    Directory of Open Access Journals (Sweden)

    Minke, G.

    2011-09-01

    Full Text Available At the Buildung Research Institute (FEB, Faculty of Architecture, University of Kassel, Germany, in the last years several hundred tests were made to study the characteristics of different loam mortars in respect of their linear shrinkage, absorption of humidity and their resistance against abrasion and erosion. In order to get data about abrasion and erosion new test methods and special apparatusses were developed. The mortars tested, chosen from the market, showed extremely varying test results.

    En el Laboratorio de Construcciones Experimentales (FEB de la Facultad de Arquitectura, Universidad de Kassel, Alemania, fueron testeados cientos de diferentes pruebas de revoque de barro para estudiar su contracción durante el secado, su absorción de humedad y su resistencia contra abrasión, erosión y absorción. Para recibir datos sobre abrasión y erosión, nuevas aparatos y metodos fueron desarrollados. Los resultados de los revoques comprados en el mercado muestran gran diferencias en los valores.

  14. ESBL Detection: Comparison of a Commercially Available Chromogenic Test for Third Generation Cephalosporine Resistance and Automated Susceptibility Testing in Enterobactericeae.

    Directory of Open Access Journals (Sweden)

    Mohamed Ramadan El-Jade

    Full Text Available Rapid detection and reporting of third generation cephalosporine resistance (3GC-R and of extended spectrum betalactamases in Enterobacteriaceae (ESBL-E is a diagnostic and therapeutic priority to avoid inefficacy of the initial antibiotic regimen. In this study we evaluated a commercially available chromogenic screen for 3GC-R as a predictive and/or confirmatory test for ESBL and AmpC activity in clinical and veterinary Enterobacteriaceae isolates. The test was highly reliable in the prediction of cefotaxime and cefpodoxime resistance, but there was no correlation with ceftazidime and piperacillin/tazobactam minimal inhibitory concentrations. All human and porcine ESBL-E tested were detected with exception of one genetically positive but phenotypically negative isolate. By contrast, AmpC detection rates lay below 30%. Notably, exclusion of piperacillin/tazobactam resistant, 3GC susceptible K1+ Klebsiella isolates increased the sensitivity and specificity of the test for ESBL detection. Our data further imply that in regions with low prevalence of AmpC and K1 positive E. coli strains chromogenic testing for 3GC-R can substitute for more time consuming ESBL confirmative testing in E. coli isolates tested positive by Phoenix or VITEK2 ESBL screen. We, therefore, suggest a diagnostic algorithm that distinguishes 3GC-R screening from primary culture and species-dependent confirmatory ESBL testing by βLACTATM and discuss the implications of MIC distribution results on the choice of antibiotic regimen.

  15. Wetting Resistance of Commercial Membrane Distillation Membranes in Waste Streams Containing Surfactants and Oil

    Directory of Open Access Journals (Sweden)

    Lies Eykens

    2017-01-01

    Full Text Available Water management is becoming increasingly challenging and several technologies, including membrane distillation (MD are emerging. This technology is less affected by salinity compared to reverse osmosis and is able to treat brines up to saturation. The focus of MD research recently shifted from seawater desalination to industrial applications out of the scope of reverse osmosis. In many of these applications, surfactants or oil traces are present in the feed stream, lowering the surface tension and increasing the risk for membrane wetting. In this study, the technological boundaries of MD in the presence of surfactants are investigated using surface tension, contact angle and liquid entry pressure measurements together with lab-scale MD experiments to predict the wetting resistance of different membranes. Synthetic NaCl solutions mixed with sodium dodecyl sulfate (SDS were used as feed solution. The limiting surfactant concentration was found to be dependent on the surface chemistry of the membrane, and increased with increasing hydrophobicity and oleophobicity. Additionally, a hexadecane/SDS emulsion was prepared with a composition simulating produced water, a waste stream in the oil and gas sector. When hexadecane is present in the emulsion, oleophobic membranes are able to resist wetting, whereas polytetrafluoretheen (PTFE is gradually wetted by the feed liquid.

  16. Evaluation of weight loss and surface roughness of compomers after simulated toothbrushing abrasion test

    OpenAIRE

    Rafael Francisco Lia Mondelli; Linda Wang; Fernanda Cristina Pimentel Garcia; Anuradha Prakki; José Mondelli; Eduardo Batista Franco; Aquira Ishikiriama

    2005-01-01

    This study aimed at analyzing the compomers wear by an "in vitro" toothbrushing abrasion test. The null hypotheses tested were that there would be no differences in weight loss and no significant changes in surface roughness of the compomers after this test. The utilized commercial brands were Dyract (Dentsply), Dyract AP (Dentsply), Compoglass F (Vivadent), Freedom (SDI), F2000 (3M ESPE), which were compared to the two resin composites Z100 (3M ESPE) and Silux Plus (3M ESPE). Ten cylindrical...

  17. RESISTANCE OF COATED ELECTRODES SUITABLE FOR RENOVATION OF TILLAGE TOOLS

    Directory of Open Access Journals (Sweden)

    Martin Kotus

    2013-12-01

    Full Text Available This article deals with the abrasive wear resistance of additional materials. The resistance of individual materials was figured out by determining a proportional wear resistance on a grinding fabric. Results of the experiment confirmed an increase in welds abrasive wear resistance. Chosen coated electrodes are suitable for the renovation of tillage tools of agricultural machines.

  18. Abrasive Properties of Three DifferentToothpastes

    Directory of Open Access Journals (Sweden)

    S. Shahabi

    2008-03-01

    Full Text Available Abstract:Objective: The main purpose of this study was to develop a simple reproducible system to compare abrasive effects of three different toothpastes.Materials and Methods: A specific mold was used to fabricate 37 samples made of po-lymethylmethacrylate. The samples were stroke by toothbrushes connected to a V8 Cross Brushing Machine in a solution of fluoridated toothpastes and distilled water. The samples were evaluated initially and also after 48 hours. The data were analyzed by one-way ANOVA test.Results: No significant differences was found among the three types of toothpastes after 25000 strokes (P=0.427.S. Shahabi, Department of Den-tal Materials, School of Den-tistry, Tehran University of Medical Sciences, Tehran, IranConclusion: All the three toothpastes presented same abrasive properties.

  19. Evaluation of commercial selective agars in screening for methicillin-resistant Staphylococcus aureus.

    Science.gov (United States)

    Yang, Hee-Young; Suh, Jin-Tae; Lee, Hee-Joo

    2010-01-01

    To evaluate methicillin-resistant S. aureus (MRSA) detection methods, we compared (a) mannitol salt agar with cefoxitin (MSA-FX), (b) MRSASelect agar (Bio-Rad), (c) MRSA ID (bioMerieuex), and (d) CHROMagar MRSA (BD Diagnostics) as selective media for culturing nasal swab specimens collected from intensive care unit (ICU) patients and healthcare personnel. A total of 99 (17.1%) cases of MRSA were recovered from 578 specimens. Four (5.5%) cases were identified from healthcare personnel and 95 (18.8%) were from ICU patients. The sensitivity of MSA-FX, MRSASelect, MRSA ID, and CHROMagar MRSA was 83.8, 87.9, 80.8, and 84.8% after 18 hr; 92.9, 94.9, 90.9, and 91.9% after 24 hr; and 96.0, 100, 99.0, and 99.0% after 48 hr, respectively. The specificity of MSA-FX, MRSASelect, MRSA ID, and CHROMagar MRSA was 97.7, 99.0, 98.7. and 99.8% after 18 hr; 97.1, 98.5, 98.1, and 99.5% after 24 hr; and 95.2, 97.7, 97.9, and 99.0% after 48 hr, respectively. In conclusion, all four media showed good results after the 24 hr readings, but MRSA ID and CHROMagar MRSA media required readings at 48 hr due to increased sensitivity at this time point.

  20. Structure and Abrasive Wear of Composite HSS M2/WC Coating

    Directory of Open Access Journals (Sweden)

    S. F. Gnyusov

    2012-01-01

    Full Text Available Features of phase-structure formation and abrasive wear resistance of composite coatings “WC-M2 steel” worn against tungsten monocarbide have been investigated. It was established that adding 20 wt.% WC to the deposited powder mixture leads to the increase in M6C carbide content. These carbides show a multimodal size distribution consisting of ~5.9 μm eutectic carbides along the grain boundaries, ~0.25 μm carbides dispersed inside the grains. Also a greater amount of metastable austenite (~88 vol.% is found. The high abrasive wear resistance of these coatings is provided by γ→α′-martensitic transformation and multimodal size distribution of reinforcing particles.

  1. Draft Genome Sequences of Colistin-Resistant MCR-1-Producing Escherichia coli ST1850 and ST74 Strains Isolated from Commercial Chicken Meat.

    Science.gov (United States)

    Monte, Daniel F; Fernandes, Miriam R; Cerdeira, Louise; de Souza, Tiago A; Mem, Andressa; Franco, Bernadette D G M; Landgraf, Mariza; Lincopan, Nilton

    2017-05-18

    We present here the draft genome sequences of two colistin-resistant mcr-1-carrying Escherichia coli strains belonging to sequence type 74 (ST74) and ST1850, isolated from commercial chicken meat in Brazil. Assembly of this draft genome resulted in 5,022,083 and 4,950,681 bp, respectively, revealing the presence of the IncX4 plasmid-mediated mcr-1 gene responsible for resistance to colistin. Copyright © 2017 Monte et al.

  2. Primary Crystallization Studies and Abrasion Analysis of Cr-Ni-Mo Cast Steel

    Directory of Open Access Journals (Sweden)

    Studnicki A.

    2015-12-01

    Full Text Available The article shows results of studies of primary crystallization and wear resistance of Cr-Ni-Mo cast steel intended for work in corrosive and abrasive conditions. The studies of primary crystallization were conducted with use of TDA method and modified tester allowing measurement casting cooling time influence on the cooling and crystallization curves of studied alloys. After heat treatment of examined cast steel wear tests of the samples were conducted on pin-on-disc type device.

  3. The characterization of Salmonella enterica serotypes isolated from the scalder tank water of a commercial poultry processing plant: Recovery of a multidrug-resistant Heidelberg strain.

    Science.gov (United States)

    Rothrock, Michael J; Ingram, Kimberly D; Gamble, John; Guard, Jean; Cicconi-Hogan, Kellie M; Hinton, Arthur; Hiett, Kelli L

    2015-03-01

    The recent multistate outbreak of a multidrug-resistant (MDR) Salmonella Heidelberg strain from commercial poultry production highlights the need to better understand the reservoirs of these zoonotic pathogens within the commercial poultry production and processing environment. As part of a larger study looking at temporal changes in microbial communities within the major water tanks within a commercial processing facility, this paper identifies and characterizes Salmonella enterica isolated from the water in a final scalder tank at 3 times during a typical processing day: prior to the birds entering the tank (start), halfway through the processing day (mid), and after the final birds were scalded (end). Over 3 consecutive processing days, no Salmonella were recovered from start-of-day water samples, while a total of 56 Salmonella isolates were recovered from the mid-day and end-of-day scalder water samples. Traditional and newer PCR-based serotyping methods eventually identified these isolates as either group C3 S. Kentucky (n=45) and group B S. Heidelberg (n=11). While none of the S. Kentucky isolates possessed any resistances to the antimicrobials tested, all S. Heidelberg isolates were found to be multidrug resistant to 5 specific antimicrobials representing 3 antimicrobial classes. Due to the potential public health impact of S. Heidelberg and the recent nationwide poultry-associated outbreak of multidrug-resistant S. Heidelberg, future studies should focus on understanding the transmission and environmental growth dynamics of this serotype within the commercial poultry processing plant environment. © 2015 Poultry Science Association Inc.

  4. The role of the toothbrush in the abrasion process.

    Science.gov (United States)

    Tellefsen, G; Liljeborg, A; Johannsen, A; Johannsen, G

    2011-11-01

    To evaluate the relative abrasivity of different toothbrushes both qualitatively and quantitatively. Acrylic plates were exposed to brushing in a brushing machine with ten different toothbrushes with water alone and with a toothpaste. The results were evaluated using a profilometer after one and 6 h of brushing (corresponding to 2000 and 12,000 double strokes, respectively). A surface roughness value (Ra-value) and also a volume loss value were calculated from the profilometer measurements. These values were then compared to each other. The results showed that brushing with water alone caused less abrasion than when a toothpaste was added. Six-hour brushing with water caused less abrasion than 1 h with a toothpaste. The number of filaments or filament diameter influenced the results in various ways. When brushing with water, the harder toothbrush (Jordan Medium) caused more abrasion (higher Ra-value), but when adding the toothpaste, the softer toothbrush (Jordan soft) caused more abrasion after 12,000 double strokes. Besides supporting the fact that a toothpaste is needed to create a significant abrasion, this study also showed that a softer toothbrush can cause as much and in some cases more abrasion than harder ones. When conducting abrasivity studies, it is important to look at both the quantitative and qualitative aspect of abrasivity. © 2011 John Wiley & Sons A/S.

  5. Machining human dentin by abrasive water jet drilling.

    Science.gov (United States)

    Kohorst, Philipp; Tegtmeyer, Sven; Biskup, Christian; Bach, Friedrich-Wilhelm; Stiesch, Meike

    2014-01-01

    The aim of this experimental in-vitro study was to investigate the machining of human dentin using an abrasive water jet and to evaluate the influence of different abrasives and water pressures on the removal rate. Seventy-two human teeth had been collected after extraction and randomly divided into six homogeneous groups (n=12). The teeth were processed in the area of root dentin with an industrial water jet device. Different abrasives (saccharose, sorbitol, xylitol) and water pressures (15 or 25 MPa) were used in each group. Dimensions of dentin removal were analysed using a stripe projection microscope and both drilling depth as well as volume of abrasion were recorded. Morphological analyses of the dentin cavities were performed using scanning electron microscopy (SEM). Both drilling depth and volume of abrasion were significantly influenced by the abrasive and the water pressure. Depending on these parameters, the drilling depth averaged between 142 and 378 μm; the volume of abrasion averaged between 0.07 and 0.15 mm3. Microscopic images revealed that all cavities are spherical and with clearly defined margins. Slight differences between the abrasives were found with respect to the microroughness of the surface of the cavities. The results indicate that abrasive water jet machining is a promising technique for processing human dentin.

  6. Abrasive water jet: a complementary tool

    Directory of Open Access Journals (Sweden)

    Duarte, J. P.

    1998-04-01

    Full Text Available The abrasive water jet is a powerful cutting tool, whose main advantages lie in the absence of thermal effects and the capability of cutting highly thick materials. Compared with Laser, the abrasive water jet allows the cutting of a larger range of thicknesses and a wider variety of materials such as: ornamental stones, metals, polymers, composites, wood, glass and ceramics. The application of this technology has suffered an extensive growth, with successful applications in varied industrial sectors like the automotive, aerospace, textile, metalworking, ornamental stones, etc. The present communication aims at introducing the abrasive water jet as a complementary tool to laser cutting, presenting its advantages by showing some documented examples of pieces cut for different industries.

    O jacto de água abrasivo é uma poderosa ferramenta de corte, tendo como principais vantagens a ausência de processo térmico e permitir o corte de elevadas espessuras. Comparativamente com o laser o jacto de água abrasivo permite cortar uma maior gama de espessuras, e uma maior diversidade de materiais: rochas ornamentais, metais, polimeros, compósitos, madeiras, vidro e cerâmicos. A aplicação desta tecnologia tem sofrido um crescimento acentuado, existindo aplicações de sucesso nos mais variados sectores industriáis como a indústria automóvel, aeroespacial, têxtil, metalomecânica e rochas ornamentáis. Esta comunição pretende apresentar o corte por jacto de agua abrasivo como uma ferramenta de corte complementar ao corte por laser, apresentando as suas vantagens documentadas através de alguns exemplos de peças executadas para as diferentes indústrias.

  7. the use of opto of pfa-based abrasive t based abrasive t micro se

    African Journals Online (AJOL)

    User

    jet technology. were made using an advanced opto were made using an advanced opto-digital microsco digital microsco software STREAM Motion Desktop 1.8. analyses of the acquired grinding whe some of the characteristic elements of structure of abrasive grains, free intergranular spaces. application of this microscopic ...

  8. Comparison of Eimeria species distribution and salinomycin resistance in commercial broiler operations utilizing different coccidiosis control strategies.

    Science.gov (United States)

    Jenkins, M; Klopp, S; Ritter, D; Miska, K; Fetterer, R

    2010-09-01

    The purpose of the present study was to evaluate the species composition and salinomycin sensitivity of Eimeria oocysts isolated from commercial broiler farms that differed by means of coccidiosis control (anticoccidial drugs [ACD] vs. live oocyst vaccines [VAC]). A comparison of Eimeria species composition and salinomycin sensitivity was also made before and after a producer switched from salinomycin to live oocyst vaccines. In general, no significant difference was observed in the concentration of Eimeria spp. oocysts in litter from VAC-utilizing farms compared to litter from ACD-utilizing farms. Application of PCR-based methods to detect coccidia found that Eimeria species distribution in litter from VAC operations more closely resembled the species composition in the live oocyst vaccines. Drug sensitivity testing found that Eimeria oocysts from VAC operations displayed greater salinomycin sensitivity as measured by weight gain and feed conversion efficiency compared to oocysts from ACD farms. These findings provide additional evidence for the usefulness of live oocyst vaccines to restore ionophore sensitivity in poultry operations that contain an ionophore-resistant population of Eimeria spp. oocysts.

  9. IN VITRO EFFICACY OF COMMERCIAL ACARICIDES INDICATE RESISTANT POPULATIONS OF RHIPICEPHALUS (BOOPHILUS MICROPLUS IN NORTHERN REGION OF MATO GROSSO

    Directory of Open Access Journals (Sweden)

    C. Eckstein

    2016-02-01

    Full Text Available Ticks are responsible for high economic and production losses on cattle production, and the use of acaricides is the main form of control applied. In recent decades, the resistance of ticks to acaricides was exacerbated by incorrect use of products, compromising the effectiveness of treatments. This study aimed to determine in vitro effectiveness of commercial acaricides in six populations of Rhipicephalus (Boophilus microplus in northern region of Mato Grosso. On average 100 engorged females were collected from each herd, which were selected and separated into homogeneous groups, sanitized, and immersed to acaricide diluted according to the manufacturer's statement, on sequence there was incubated. After the incubation was obtained from female reproductive efficiency and effectiveness of the tested acaricides. The association cypermethrin+ chlorpyrifos + citronellal showed satisfactory efficiency (> 95% in all the properties (mean 99.86% in properties, followed by trichlorfon (83.45%, amitraz (72.33%, neem oil (67.23% and cypermethrin (22.97%, which was not effective in any property. It indicates the use of the association cypermethrin +chlorpyrifos+ citronellal on evaluated properties for control of cattle tick effectively.

  10. Aeolian Rat Tails (ARTs): A New Morphological Indicator of Abrasion Direction

    Science.gov (United States)

    Favaro, E. A.; Hugenholtz, C.; Barchyn, T.

    2016-12-01

    Aeolian rat tails (ARTs) are a previously undocumented aeolian abrasion feature observed on ignimbrite surfaces in the Puna Plateau of Northwest Argentina and bare morphological similarity to small-scale features on Mars. We describe the terrestrial features and present an evolutionary sequence from inception to demise. ARTs are regionally-ubiquitous and characterized by a windward abrasion-resistant lithic clast and a downwind-tapering tail. The size of ARTs is controlled by the diameter of the windward lithic clast, observed on the sub-decimeter to meter scale. Their distribution throughout the Campo de Piedra Pómez, and adjacent regions is determined by the ignimbrite clast content. ARTs develop under a uni-modal abrasion direction when lithic clasts are eroded out of the ignimbrite matrix, protrude from the surface, and shelter material directly behind the clast. As the surrounding material is eroded away, a downwind-tapered tail develops. Continued erosion of the adjacent surface leads to the undercutting of clasts, liberating them from the feature where, if small enough, the clasts can be transported downwind, leading to the destruction of the tail and ultimately the feature. This evolutionary sequence accounts not only for the morphology of the feature, but also the presence of loose clasts on the ignimbrite surface, which plays a role in the development of other enigmatic landforms in the area, such as periodic bedrock ridges, yardangs, and megaripples. The significance of the identification of ARTs is due to the necessity of uni-modal abrasion direction for their development, thereby making their orientation a diagnostic indicator of long-term aeolian abrasion direction. ARTs are likely analogs of features identified by MSL Curiosity Rover on Mars, possibly providing information on past and present wind regimes.

  11. Impact of toothpaste slurry abrasivity and toothbrush filament stiffness on abrasion of eroded enamel - an in vitro study

    OpenAIRE

    Wiegand, Annette; Schwerzmann, Martina; Sener, Beatrice; Magalhães, Ana C.; Roos, Malgorzata; Ziebolz, Dirk; Imfeld, Thomas; Attin, Thomas

    2008-01-01

    OBJECTIVE: Toothbrush abrasion is significant in the development of tooth wear, particularly when combined with erosion. This in vitro study aimed to evaluate the impact of toothpaste slurry abrasivity and toothbrush filament stiffness on abrasion of eroded enamel. MATERIAL AND METHODS: Eroded enamel samples (hydrochloric acid, pH: 2.6, 15 s) were brushed with 40 strokes in an automatic brushing machine using manual toothbrushes with different filament stiffness (filament diameter: 0.15, 0.20...

  12. Investigation on two-body abrasive wear behavior of titanium ...

    African Journals Online (AJOL)

    Investigation on two-body abrasive wear behavior of titanium carbide filled glass fabric-epoxy composites- a Box-Behnken approach. ... International Journal of Engineering, Science and Technology ... The two-body abrasive wear behavior of Glass–Epoxy (G–E) composites has been evaluated by the addition of Titanium

  13. Anisotropy abrasive wear behavior of bagasse fiber reinforced ...

    African Journals Online (AJOL)

    Anisotropy abrasive wear behavior of bagasse fiber reinforced polymer composite. ... International Journal of Engineering, Science and Technology ... Three different types of abrasives wear behaviour have been observed in the composite in three orientations and follow the following trends: WNO < WAPO < WPO, where ...

  14. Neuro - Fuzzy Analysis for Silicon Carbide Abrasive Grains ...

    African Journals Online (AJOL)

    Grinding wheels are made of very small, sharp and hard abrasive materials or grits held together by strong porous bond. Abrasive materials are materials of extreme hardness that are used to shape other materials by a grinding or abrading action and they are used either as loose grains, as grinding wheels, or as coatings ...

  15. Impact of toothpaste slurry abrasivity and toothbrush filament stiffness on abrasion of eroded enamel - an in vitro study.

    Science.gov (United States)

    Wiegand, Annette; Schwerzmann, Martina; Sener, Beatrice; Magalhaes, Ana Carolina; Roos, Malgorzata; Ziebolz, Dirk; Imfeld, Thomas; Attin, Thomas

    2008-08-01

    Toothbrush abrasion is significant in the development of tooth wear, particularly when combined with erosion. This in vitro study aimed to evaluate the impact of toothpaste slurry abrasivity and toothbrush filament stiffness on abrasion of eroded enamel. Eroded enamel samples (hydrochloric acid, pH: 2.6, 15 s) were brushed with 40 strokes in an automatic brushing machine using manual toothbrushes with different filament stiffness (filament diameter: 0.15, 0.20, or 0.25 mm). A paste-free control slurry (relative enamel abrasion (REA) value 2) and toothpaste slurries with different abrasivity (REA values 6 or 9) were used for brushing. Erosion and abrasion were followed by storing the enamel samples in artificial saliva for 3 h. After each 4th cycle, the samples were stored in artificial saliva for 15 h. After 60 cycles, enamel loss was measured by profilometry and statistically analyzed by two-way and one-way ANOVA and Bonferroni/Dunn post-hoc tests. Loss of enamel (mean, microm) was influenced mainly by the abrasivity of the slurry and increased along with REA value (REA 2: 0.0-0.2, REA 6: 2.1-3.3, REA 9: 2.9-3.7). Abrasion of eroded enamel was also affected by filament stiffness of the toothbrush, but only groups brushed with toothpaste slurry of REA 6 showed any significant difference between the different toothbrushes. Thereby, toothbrushes with 0.2 mm filament diameter caused higher enamel loss than 0.15 and 0.25 mm filaments. Toothbrush abrasion of eroded enamel is influenced mainly by the abrasivity of the toothpaste slurry, but is also modified by toothbrush filament stiffness.

  16. Analysis of Two Methods for Characterization of Flame Resistant Military Fabrics and Commercial Textile Fibers: Simultaneous DSC-TGA and Pyrolysis GCMS

    Science.gov (United States)

    2014-04-04

    and high performance fibers such as meta- aramid (Nomex®) and para- aramid (Kevlar®, Twaron®) for decades. It is reported that pyrolysis measurements...no distinguishable difference between the Kevlar® and Twaron® fibers in the SDT results; both were para- aramid fibers processed differently from...FOR CHARACTERIZATION OF FLAME RESISTANT MILITARY FABRICS AND COMMERCIAL TEXTILE FIBERS : SIMULTANEOUS DSC-TGA AND PYROLYSIS GCMS by Pearl W

  17. High Voltage Resistive Divider Based on Cast Microwire in Glass Insulation on 6–24 kV Alternating Current of Commercial Frequency.

    Directory of Open Access Journals (Sweden)

    Juravleov A.

    2008-12-01

    Full Text Available It is presented the analysis and description of the construction of the high voltage resistive divider on the base of cast microwire in glass insulation on 6–24 kV alternating current of commercial frequency. It is presented the procedure of compensation of frequency error during the process of fabrication of divides and results of tests of the sample model of the divider as well.

  18. An abrasive wear study of ordered Fe[sub 3]Al. [Fe[sub 73]Al[sub 27], Fe[sub 76]Al[sub 24], Fe[sub 77]Al[sub 23

    Energy Technology Data Exchange (ETDEWEB)

    Maupin, H.E.; Wilson, R.D.; Hawk, J.A. (US Bureau of Mines, Albany Research Center, OR (United States))

    1992-12-01

    Abrasive wear research has been conducted on ordered iron aluminide intermetallics. Pin-on-drum abrasive wear tests were performed on samples of varying long-range order. Wear surfaces were examined with optical microscopy, transmission electron microscopy (TEM), scanning electron microscopy and X-ray diffraction. The wear mechanism consisted of microplowing, micromachining and microfracture. Compositional variation near Fe[sub 3]Al and the degree of long-range ordering had only minor effects on the abrasive wear rates of iron aluminide samples. TEM analysis of the wear surfaces indicated that significant plastic deformation and recrystallization had occurred. The abrasive wear rates were compared with those of well-known abrasive wear-resistant materials. (orig.).

  19. FE simulation of the indentation deformation of SiC modified vinylester composites in respect to their abrasive wear performance

    Directory of Open Access Journals (Sweden)

    2008-10-01

    Full Text Available The abrasive sliding friction and wear behaviours of silicon carbide (SiC filled vinylester (VE composites were investigated. The average grain size of the incorporated SiC particles was varied, holding the volume content of them in every case at 16 vol%. Mechanical properties (hardness, compression modulus, yield stress of the filled and neat VE were determined. The tribological properties were investigated in block (composite – on – ring (steel test configuration. The steel counter bodies were covered with abrasive papers of different graining. Coefficient of friction (COF and specific wear rate of the VE + SiC composites were determined. It was observed that the wear resistance increases with increasing average filler grain size and with decreasing abrasiveness of the counter surface. The COF of the VE + SiC composites is independent of the size of the incorporated particles, but it is strongly influenced by the abrasiveness of the counter body. The worn surfaces of the VE + SiC systems were analysed in scanning electron microscope (SEM to deduce the typical wear mechanisms. The size effect of the SiC filler particles onto the abrasive wear characteristics was investigated by assuming that the roughness peaks of the abrasive paper and the indenter of the microhardness test cause similar micro scaled contact deformations in the composites. Therefore FE method was used to simulate the micro scaled deformation process in the VE + SiC systems during microindentation tests. The FE results provided valuable information on how to explain the size effect of the incorporated SiC filler.

  20. Genetic characterisation of antimicrobial resistance and virulence genes in Staphylococcus aureus isolated from commercial broiler chickens in the Durban metropolitan area, South Africa

    Directory of Open Access Journals (Sweden)

    Nelisiwe Mkize

    2017-01-01

    Full Text Available Antimicrobial resistance of Staphylococcus aureus in human and veterinary medicine is a serious worldwide problem. The aim of this study was to investigate the prevalence of S. aureus in commercial broiler chickens as well as to establish antimicrobial susceptibility and the distribution of genetic determinants conferring resistance and virulence. One hundred and ninety-four samples were aseptically collected from broiler chicken slaughterhouses and retail outlets around the Durban metropolitan area in South Africa. Microbiological and molecular methods were used to detect the presence of S. aureus as well as its resistance- and virulence-associated genes. Polymerase chain reaction (PCR was used to confirm the presence of S. aureus by amplifying the nuc gene. Approximately 54% of 194 samples were positive for S. aureus. The disc diffusion technique was used to investigate antimicrobial susceptibility profiles of the S. aureus isolates to a battery of 10 antimicrobial agents, namely ampicillin, chloramphenicol, gentamicin, erythromycin, cefoxitin, kanamycin, streptomycin, tetracycline, vancomycin and trimethoprim. The results demonstrated that S. aureus isolates of abattoir origin had a high level (79.4% of resistance to tetracycline, followed by ampicillin, vancomycin, cefoxitin, trimethoprim, erythromycin and streptomycin with resistance rates of 65.1%, 61.9%, 60.3%, 58.7%, 57.1% and 46.0%, respectively. Staphylococcus aureus isolates of retail origin exhibited higher antimicrobial resistance prevalence rates than those of abattoir origin. Tetracycline had the highest resistance rate (100%, followed by cefoxitin (91.7%, erythromycin (83.3%, streptomycin (83.3% and kanamycin (66.7%. All isolates were resistant to two or more antimicrobial agents. Out of the four virulence genes that were screened, only two were detected (coagulase and protein A; however, their prevalence rates were very low. All antimicrobial resistance genes screened were

  1. The interactions between attrition, abrasion and erosion in tooth wear.

    Science.gov (United States)

    Shellis, R Peter; Addy, Martin

    2014-01-01

    Tooth wear is the result of three processes: abrasion (wear produced by interaction between teeth and other materials), attrition (wear through tooth-tooth contact) and erosion (dissolution of hard tissue by acidic substances). A further process (abfraction) might potentiate wear by abrasion and/or erosion. Knowledge of these tooth wear processes and their interactions is reviewed. Both clinical and experimental observations show that individual wear mechanisms rarely act alone but interact with each other. The most important interaction is the potentiation of abrasion by erosive damage to the dental hard tissues. This interaction seems to be the major factor in occlusal and cervical wear. The available evidence is insufficient to establish whether abfraction is an important contributor to tooth wear in vivo. Saliva can modulate erosive/abrasive tooth wear, especially through formation of pellicle, but cannot prevent it. © 2014 S. Karger AG, Basel.

  2. Refractory, Abrasive, and Other Industrial Minerals Operations - Direct Download

    Data.gov (United States)

    U.S. Geological Survey, Department of the Interior — This map layer includes refractory, abrasive, and other industrial minerals operations in the United States. The data represent commodities covered by the Minerals...

  3. An easy classification for dental cervical abrasions

    Directory of Open Access Journals (Sweden)

    Madhuri Alankar Sawai

    2014-01-01

    Full Text Available Introduction: Tooth wear - attrition, abrasion, or erosion - are modern day problems for dentistry. It usually leads to discomfort and sensitivity especially during eating, drinking, or tooth brushing. If left untreated for a long time, it may lead to loss of vitality of tooth. Various qualitative and quantitative methods have been used in the past to describe tooth wear. However, each method has certain shortfalls. There is no ideal index that is simple and clear in its scoring criteria. The Hypothesis: The classifications described in the literature are very descriptive and hence, it takes a long time to grade for a complete dentition. Some are based on the morphologic appearance and others on severity. A classification system has to facilitate standardized identification of a condition and help in diagnosis and treatment planning. The present manuscript is an attempt to emphasize the need to develop a classification system that is easy to score and describes the condition in details without utilizing much time. Evaluation of the Hypothesis: The hypothesis highlights some drawbacks of the classification systems available today and puts forth a new and easy to use classification system.

  4. Computed tomography to quantify tooth abrasion

    Science.gov (United States)

    Kofmehl, Lukas; Schulz, Georg; Deyhle, Hans; Filippi, Andreas; Hotz, Gerhard; Berndt-Dagassan, Dorothea; Kramis, Simon; Beckmann, Felix; Müller, Bert

    2010-09-01

    Cone-beam computed tomography, also termed digital volume tomography, has become a standard technique in dentistry, allowing for fast 3D jaw imaging including denture at moderate spatial resolution. More detailed X-ray images of restricted volumes for post-mortem studies in dental anthropology are obtained by means of micro computed tomography. The present study evaluates the impact of the pipe smoking wear on teeth morphology comparing the abraded tooth with its contra-lateral counterpart. A set of 60 teeth, loose or anchored in the jaw, from 12 dentitions have been analyzed. After the two contra-lateral teeth were scanned, one dataset has been mirrored before the two datasets were registered using affine and rigid registration algorithms. Rigid registration provides three translational and three rotational parameters to maximize the overlap of two rigid bodies. For the affine registration, three scaling factors are incorporated. Within the present investigation, affine and rigid registrations yield comparable values. The restriction to the six parameters of the rigid registration is not a limitation. The differences in size and shape between the tooth and its contra-lateral counterpart generally exhibit only a few percent in the non-abraded volume, validating that the contralateral tooth is a reasonable approximation to quantify, for example, the volume loss as the result of long-term clay pipe smoking. Therefore, this approach allows quantifying the impact of the pipe abrasion on the internal tooth morphology including root canal, dentin, and enamel volumes.

  5. Minimal alterations on the enamel surface by micro-abrasion: in vitro roughness and wear assessments

    Directory of Open Access Journals (Sweden)

    Marcela Charantola Rodrigues

    2013-04-01

    Full Text Available Objective: To evaluate the in vitro changes on the enamel surface after a micro-abrasion treatment promoted by different products. Material and Methods: Fifty (50 fragments of bovine enamel (15 mm × 5 mm were randomly assigned to five groups (n=10 according to the product utilized: G1 (control= silicone polisher (TDV, G2= 37% phosphoric acid (3M/ESPE + pumice stone (SS White, G3= Micropol (DMC Equipment, G4= Opalustre (Ultradent and G5= Whiteness RM (FGM Dental Products. Roughness and wear were the responsible variables used to analyze these surfaces in four stages: baseline, 60 s and 120 s after the micro-abrasion and after polishing, using a Hommel Tester T1000 device. After the tests, a normal distribution of data was verified, with repeated ANOVA analyses (p≤0.05 which were used to compare each product in different stages. One-way ANOVA and Tukey tests were applied for individual comparisons between the products in each stage (p≤0.05. Results: Means and standard deviations of roughness and wear (µm after all the promoted stages were: G1=7.26(1.81/13.16(2.67, G2=2.02(0.62/37.44(3.33, G3=1.81(0.91/34.93(6.92, G4=1.92(0.29/38.42(0.65 and G5=1.98(0.53/33.45(2.66. At 60 seconds, all products tended to produce less surface roughness with a variable gradual decrease over time. After polishing, there were no statistically significant differences between the groups, except for G1. Independent of the product utilized, the enamel wear occurred after the micro-abrasion. Conclusions: In this in vitro study, enamel micro-abrasion presented itself as a conservative approach, regardless of the type of the paste compound utilized. These products promoted minor roughness alterations and minimal wear. The use of phosphoric acid and pumice stone showed similar results to commercial products for the micro-abrasion with regard to the surface roughness and wear.

  6. Minimal alterations on the enamel surface by micro-abrasion: in vitro roughness and wear assessments.

    Science.gov (United States)

    Rodrigues, Marcela Charantola; Mondelli, Rafael Francisco Lia; Oliveira, Gabriela Ulian; Franco, Eduardo Batista; Baseggio, Wagner; Wang, Linda

    2013-01-01

    To evaluate the in vitro changes on the enamel surface after a micro-abrasion treatment promoted by different products. Fifty (50) fragments of bovine enamel (15 mm × 5 mm) were randomly assigned to five groups (n=10) according to the product utilized: G1 (control)= silicone polisher (TDV), G2= 37% phosphoric acid (3M/ESPE) + pumice stone (SS White), G3= Micropol (DMC Equipment), G4= Opalustre (Ultradent) and G5= Whiteness RM (FGM Dental Products). Roughness and wear were the responsible variables used to analyze these surfaces in four stages: baseline, 60 s and 120 s after the micro-abrasion and after polishing, using a Hommel Tester T1000 device. After the tests, a normal distribution of data was verified, with repeated ANOVA analyses (p≤0.05) which were used to compare each product in different stages. One-way ANOVA and Tukey tests were applied for individual comparisons between the products in each stage (p≤0.05). Means and standard deviations of roughness and wear (µm) after all the promoted stages were: G1=7.26(1.81)/13.16(2.67), G2=2.02(0.62)/37.44(3.33), G3=1.81(0.91)/34.93(6.92), G4=1.92(0.29)/38.42(0.65) and G5=1.98(0.53)/33.45(2.66). At 60 seconds, all products tended to produce less surface roughness with a variable gradual decrease over time. After polishing, there were no statistically significant differences between the groups, except for G1. Independent of the product utilized, the enamel wear occurred after the micro-abrasion. In this in vitro study, enamel micro-abrasion presented itself as a conservative approach, regardless of the type of the paste compound utilized. These products promoted minor roughness alterations and minimal wear. The use of phosphoric acid and pumice stone showed similar results to commercial products for the micro-abrasion with regard to the surface roughness and wear.

  7. An investigation of abrasive wear and corrosion behavior of surface repair of gray cast iron by SMAW

    Directory of Open Access Journals (Sweden)

    Alireza Sadeghi

    2017-01-01

    Full Text Available In this work, improving the abrasion–corrosion behavior of gray cast iron used in centrifugal pumps was studied. These pumps are usually made of gray cast iron (BS:1452Gr220 and are repaired by Shielded Metal Arc Welding (SMAW. Three different typical welding electrodes including Ni electrode (DIN8563, Carbon Steel electrode (DIN1913, and Hardening electrode (DIN8555 were used to compare the weldability of the base metal. Microstructural differences for three types of electrodes were studied and forming of different phases was analyzed. Corrosion and abrasion tests were conducted and related to welding conditions. Experimental results showed that using Ni substrate electrode reduce the unwanted phases (martensitic and carbides. Furthermore, in comparison with the base metal, the abrasion behavior of all weldments was improved. It was also determined that the carbon steel electrode has a higher corrosion resistance in zero-resistance ammeter (ZRA test compared to other electrodes.

  8. Abrasion of eroded dentin caused by toothpaste slurries of different abrasivity and toothbrushes of different filament diameter.

    Science.gov (United States)

    Wiegand, Annette; Kuhn, Mirjam; Sener, Beatrice; Roos, Malgorzata; Attin, Thomas

    2009-06-01

    This study aimed to evaluate the impact of toothpaste slurry abrasivity and toothbrush filament diameter on abrasion of eroded dentin in vitro. Eroded dentin samples (hydrochloric acid, pH 2.6, 15s) were brushed with 40 strokes in an automatic brushing machine using manual toothbrushes with different filament diameter (0.15, 0.20 or 0.25 mm). The toothbrushes were applied with a control slurry free of abrasive particles (RDA-value 10) or toothpastes slurries with different abrasivity (RDA-values 20, 50 or 100). Each erosive-abrasive cycle was followed by storage of the dentin samples in artificial saliva for 3h. After each 4 cycles, the samples were stored in artificial saliva for 15 h. After 60 cycles, dentin loss was measured by profilometry and statistically analysed by ANOVA and linear regression analysis. Dentin loss increased along with the RDA-value of the toothpaste slurries. The impact of the filament diameter on dentin loss was less evident compared to the RDA-value. However, toothbrushes with smaller filament stiffness caused higher dentin wear in all toothpaste slurry groups (RDA 20, 50 and 100) except for the paste-free control group (RDA 10). Abrasion of eroded dentin increased along with the RDA-value of the toothpaste slurry and with decreasing filament diameter of the toothbrush.

  9. Scientific Opinion on the influence of genetic parameters on the welfare and the resistance to stress of commercial broilers

    DEFF Research Database (Denmark)

    Morton, David; Oltenacu, Toni; Arnould, Cécile

    2010-01-01

      This scientific opinion describes the influence of genetic parameters that have affected the welfare of commercial broilers. There is a lack of robust scientific data for Europe on welfare outcome indicators and these should be recorded independently and made publicly available. The major welfa...

  10. EFECTO DEL CONTENIDO DE CARBONO SOBRE LA RESISTENCIA AL DESGASTE ABRASIVO DE RECUBRIMIENTOS DE CrC DEPOSITADOS POR PULVERIZACIÓN CATÓDICA MAGNETRÓN EFEITO DO CONTEÚDO DE CARBONO SOBRE A RESISTÊNCIA AO DESGASTE ABRASIVO DE RECOBRIMENTOS DE CrC DEPOSITADOS POR PULVERIZAÇÃO CATÓDICA MAGNETRÃO EFFECT OF THE CARBON CONTENT IN ABRASIVE WEAR RESISTANCE OF CrC COATINGS DEPOSITED BY MAGNETRON SPUTTERING

    Directory of Open Access Journals (Sweden)

    Maryory Astrid Gómez

    2012-12-01

    diamante. O volume das impressões de abrasão mediu-se com as imagens obtidas no microscópio interferométrico e ademais se corroborou com o cálculo do volume geométrico baseado em seções medidas com o perfilômetro. O comportamento ao desgaste abrasivo mostrou uma marcada dependência com o conteúdo de carbono. O desgaste abrasivo mais baixo obtevese para os recobrimentos com o mais alto conteúdo de carbono.Chromium carbide coatings on steel are a good candidate for applications on forming and molding dies. The high mechanical strength, chemical resistance and high temperature stability of Cr3C2 phase can be compatible with the severe abrasive wear and corrosion found in those manufacture operations. In this work chromium carbide coatings deposited by means of RF magnetron sputtering showed carbon contents between 25 % and 58 % by EDS analysis. Hardness values of these coatings were between 15 and 24 GPa, being the hardest values in the samples with carbon content in the 39-53 % range. The abrasive wear behavior of the coatings was evaluated by using a dimple grinder with diamond powder. The volume of the abrasion craters was measured from the images obtained with the interferometric microscope, and further corroborated by geometrical volume calculation based in profilometer sections that were measured. Abrasive wear behavior showed a marked dependence with carbon content. The lowest abrasive wear was obtained for the coatings with the highest carbon content.

  11. Abrasions and lameness in piglets born in different farrowing systems with different types of floor

    Science.gov (United States)

    Zoric, Mate; Nilsson, Ebba; Mattsson, Sigbrit; Lundeheim, Nils; Wallgren, Per

    2008-01-01

    Background The quality of the floor is essential to the welfare of piglets as abrasions often are recorded in newborn piglets, and such lesions may lead to lameness. Apart from animal suffering, lameness contributes to losses in form of dead piglets, decreased growth, and increased use of antibiotics and manual labour. Methods In a herd with three different farrowing systems, 37 litters (390 piglets) were studied until the age of 3 weeks with respect to presence of skin wounds and abrasions. Lameness was registered until the age of 7 weeks. Eight lame piglets were sacrificed before medical treatment and subjected to necropsy including histopathological and microbiological examinations. Isolates of streptococci, staphylococci and E. coli were tested with respect to antimicrobial resistance. Mastitis was observed in ten sows. Results The most severe abrasions at carpus and soles were seen in the system with a new solid concrete floor with a slatted floor over the dunging area. The lowest magnitude was observed in the deep litter system with peat. Sole bruising was more common in the systems with concrete floor compared to the deep litter system with peat, and the differce in prevalence was significant at all examination days. The lesions decreased with time and about 75% of the treatments for lameness were performed during the first three weeks of life. The overall prevalence of lameness was highest in the system with new solid concrete floor with a slatted floor over the dunging area (9.4%) followed by the old solid concrete floor (7.5%). A lower (p < 0.05) prevalence was seen in the deep litters system with peat (3.3%). No significant relationship between mastitis and abrasions or lameness in the offspring was observed. Conclusion There were large differences in the prevalence of abrasions and lameness between the floor types. The deep litter system with peat provided a soft and good floor for piglets. The overall prevalence of lameness was only diagnosed in every

  12. Comparative Efficacy of a Soft Toothbrush with Tapered-tip Bristles to an ADA Reference Toothbrush on Gingival Abrasion over a 12-Week Period.

    Science.gov (United States)

    Gallob, John; Petrone, Dolores M; Mateo, Luis R; Chaknis, Patricia; Morrison, Boyce M; Panagakos, Foti; Williams, Malcolm

    2016-06-01

    Evaluation of the impact of a soft toothbrush with tapered-tip (Test Toothbrush) bristles and an ADA reference toothbrush (ADA Toothbrush) on gingival abrasion over a 12-week period. This was a randomized, single-center, examiner-blind, two-cell, parallel clinical research study and used the Danser Gingival Abrasion Index to assess the level of gingival abrasion after a single brushing, as well as after six weeks and 12 weeks of twice-daily brushing. Adult male and female subjects from the Central New Jersey, USA area refrained from all oral hygiene procedures for 24 hours. They reported to the study site after refraining from eating, drinking, and smoking for four hours. Following a qualifying examination using plaque and gingivitis scores along with a baseline gingival abrasion examination, subjects were randomized into two balanced groups, each group using one of the two study toothbrushes. Subjects were instructed to brush their teeth for one minute, under supervision, with their assigned toothbrush and a commercially available fluoride toothpaste (Colgate© Cavity Protection Toothpaste), after which they were again evaluated for gingival abrasion. Subjects were dismissed from the study site with their assigned toothbrush and toothpaste, and instructed to brush twice daily at home for the next 12 weeks. The subjects were instructed to brush for one minute during each tooth brushing. The subjects reported to the study site after six weeks and 12 weeks of product use, at which time they were evaluated for gingival abrasion. Seventy-one (71) subjects complied with the protocol and completed the clinical study. The results of this study showed that the Test Toothbrush provided statistically significantly (p Toothbrush after a single tooth brushing, after six weeks, and after 12 weeks of product use (75.0%, 85.5%, 73.9%, respectively). The soft toothbrush with tapered-tip bristles produced significantly less gingival abrasion after 12 weeks of product use as

  13. SYNTHESIS OF FUNCTIONALLY GRADED ALUMINIUM COMPOSITE AND INVESTIGATION ON ITS ABRASION WEAR BEHAVIOUR

    Directory of Open Access Journals (Sweden)

    N. RADHIKA

    2017-05-01

    Full Text Available Functionally graded aluminium (Al-Si5Cu3 metal matrix composite reinforced with 10 wt-percent of boron carbide particles having average size of 33 µm was synthesized through horizontal centrifugal casting method. The specimen of length 150 mm and outer diameter of 154 mm with the thickness of 20 mm was produced under the centrifuging speed of 1000 rpm. Composite specimens were prepared as per ASTM standards from the casting and subjected to microstructural evaluation, hardness testing and three body abrasion wear test. The microstructural observation was done on the surfaces at the distance of 1, 2.5, 10 and 15 mm from the outer periphery of the casting and the result shows that larger amount of particles observed at distance of 2.5 mm and very less particles observed at the distance of 15 mm. The hardness test was conducted on the different surfaces in the radial direction from the outer periphery and found decrease in hardness from 2.5 to 15 mm. The abrasion wear test was conducted using dry abrasion tester for various loads of 28, 40 and 52 N at different distances from the outer periphery of the casting and the results revealed that wear rate gradually increases when moving towards the inner periphery and also with the increasing load. Therefore higher wear resistance was observed at the outer periphery and the lower wear resistance was obtained at the inner periphery. This property makes them suitable for using in wear applications such as in cylinder liners.

  14. Heat treated twin wire arc spray AISI 420 coatings under dry and wet abrasive wear

    Science.gov (United States)

    Rodriguez, E.; González, M. A.; Monjardín, H. R.; Jimenez, O.; Flores, M.; Ibarra, J.

    2017-11-01

    The influence of applying two different heat treatments such as: deep cryogenic and tempering on dry/wet abrasive wear resistance of twin wire arc spray martensitic AISI 420 coatings was evaluated by using a modified rubber wheel type test apparatus. A load dependency was observed on the abrasive wear rate behavior of both; dry and wet tests. Three body (rolling) and two body (sliding) wear mechanisms were identified in dry conditions, prevailing rolling at lower and higher loads. However, at higher loads, more presence of grooving and pits formation was observed. Coatings tempered at 205 °C/1 h displayed better wear resistance than cryogenic treated ones. A change in wear mechanism between dry and wet conditions was observed; two body wear mechanism predominated respect to three body. In both; dry and wet conditions the microstructure (several inter-splat oxides) as well as strain and residual stress promotes brittle material removal which was more evident in cryogenic and as-sprayed samples during dry test and at higher loads in wet conditions.

  15. Adhesion and wear behaviour of NCD coatings on Si3N4 by micro-abrasion tests.

    Science.gov (United States)

    Silva, F G; Neto, M A; Fernandes, A J S; Costa, F M; Oliveira, F J; Silva, R F

    2009-06-01

    Nanocrystalline diamond (NCD) coatings offer an excellent alternative for tribological applications, preserving most of the intrinsic mechanical properties of polycrystalline CVD diamond and adding to it an extreme surface smoothness. Silicon nitride (Si3N4) ceramics are reported to guarantee high adhesion levels to CVD microcrystalline diamond coatings, but the NCD adhesion to Si3N4 is not yet well established. Micro-abrasion tests are appropriate for evaluating the abrasive wear resistance of a given surface, but they also provide information on thin film/substrate interfacial resistance, i.e., film adhesion. In this study, a comparison is made between the behaviour of NCD films deposited by hot-filament chemical vapour deposition (HFCVD) and microwave plasma assisted chemical vapour deposition (MPCVD) techniques. Silicon nitride (Si3N4) ceramic discs were selected as substrates. The NCD depositions by HFCVD and MPCVD were carried out using H2-CH4 and H2-CH4-N2 gas mixtures, respectively. An adequate set of growth parameters was chosen for each CVD technique, resulting in NCD films having a final thickness of 5 microm. A micro-abrasion tribometer was used, with 3 microm diamond grit as the abrasive slurry element. Experiments were carried out at a constant rotational speed (80 r.p.m.) and by varying the applied load in the range of 0.25-0.75 N. The wear rate for MPCVD NCD (3.7 +/- 0.8 x 10(-5) mm3 N(-1) m(-1)) is compatible with those reported for microcrystalline CVD diamond. The HFCVD films displayed poorer adhesion to the Si3N4 ceramic substrates than the MPCVD ones. However, the HFCVD films show better wear resistance as a result of their higher crystallinity according to the UV Raman data, despite evidencing premature adhesion failure.

  16. Operation-Oriented Studies on Wear Properties of Surface-Hardened Alloy Cast Steels Used in Mining in the Conditions of the Combined Action of Dynamic Forces and an Abrasive Material

    Directory of Open Access Journals (Sweden)

    Wieczorek A.N.

    2017-12-01

    Full Text Available This paper presents the results of wear tests of shot-peened and not shot-peened cast steels used in the mining machinery industry, in particular in the construction of chain drums for armoured face conveyors. Wear tests were carried out in the conditions corresponding to the real operating conditions of armoured face conveyors during drifting work in rocks such as sandstone. The operating factors subjected to the analyses included the presence of quartz abrasive and the impact of external dynamic forces. On the basis of the wear tests as well as the microhardness and microstructure examinations performed, it has been found that the action of an additional dynamic force has a synergistic impact on the process of abrasive wear in loose quartz abrasive. It has been further found that the value of abrasive wear of chain wheels operated in the conditions of a combined action of abrasive and a dynamic force depends on whether the area of mating of wheels with the chain was shot-peened or not before the wear tests – an increase in the abrasive wear was observed for the wheels made of cast steel subjected to shot peening in the area of mating with the chain. Lower resistance to abrasive wear of the cast steels subjected to shot peening before the wear tests could result from the formation of cracks in the surface layer caused by the action of shot.

  17. Effect of Abrasive Machining on the Electrical Properties Cu86Mn12Ni₂ Alloy Shunts.

    Science.gov (United States)

    Misti, Siti Nabilah; Birkett, Martin; Penlington, Roger; Bell, David

    2017-07-29

    This paper studies the effect of abrasive trimming on the electrical properties of Cu 86 Mn 12 Ni₂ Manganin alloy shunt resistors. A precision abrasive trimming system for fine tuning the resistance tolerance of high current Manganin shunt resistors is proposed. The system is shown to be capable of reducing the resistance tolerance of 100 μΩ shunts from their standard value of ±5% to <±1% by removing controlled amounts of Manganin material using a square cut trim geometry. The temperature coefficient of resistance (TCR), high current, and high temperature performance of the trimmed shunts was compared to that of untrimmed parts to determine if trimming had any detrimental effect on these key electrical performance parameters of the device. It was shown that the TCR value was reduced following trimming with typical results of +106 ppm/°C and +93 ppm/°C for untrimmed and trimmed parts respectively. When subjected to a high current of 200 A the trimmed parts showed a slight increase in temperature rise to 203 °C, as compared to 194 °C for the untrimmed parts, but both had significant temporary increases in resistance of up to 1.3 μΩ. The results for resistance change following high temperature storage at 200 °C for 168 h were also significant for both untrimmed and trimmed parts with shifts of 1.85% and 2.29% respectively and these results were related to surface oxidation of the Manganin alloy which was accelerated for the freshly exposed surfaces of the trimmed part.

  18. Effect of Abrasive Machining on the Electrical Properties Cu86Mn12Ni2 Alloy Shunts

    Directory of Open Access Journals (Sweden)

    Siti Nabilah Misti

    2017-07-01

    Full Text Available This paper studies the effect of abrasive trimming on the electrical properties of Cu86Mn12Ni2 Manganin alloy shunt resistors. A precision abrasive trimming system for fine tuning the resistance tolerance of high current Manganin shunt resistors is proposed. The system is shown to be capable of reducing the resistance tolerance of 100 μΩ shunts from their standard value of ±5% to <±1% by removing controlled amounts of Manganin material using a square cut trim geometry. The temperature coefficient of resistance (TCR, high current, and high temperature performance of the trimmed shunts was compared to that of untrimmed parts to determine if trimming had any detrimental effect on these key electrical performance parameters of the device. It was shown that the TCR value was reduced following trimming with typical results of +106 ppm/°C and +93 ppm/°C for untrimmed and trimmed parts respectively. When subjected to a high current of 200 A the trimmed parts showed a slight increase in temperature rise to 203 °C, as compared to 194 °C for the untrimmed parts, but both had significant temporary increases in resistance of up to 1.3 μΩ. The results for resistance change following high temperature storage at 200 °C for 168 h were also significant for both untrimmed and trimmed parts with shifts of 1.85% and 2.29% respectively and these results were related to surface oxidation of the Manganin alloy which was accelerated for the freshly exposed surfaces of the trimmed part.

  19. Abrasion of Candidate Spacesuit Fabrics by Simulated Lunar Dust

    Science.gov (United States)

    Gaier, James R.; Meador, Mary Ann; Rogers, Kerry J.; Sheehy, Brennan H.

    2009-01-01

    A protocol has been developed that produced the type of lunar soil abrasion damage observed on Apollo spacesuits. This protocol was then applied to four materials (Kevlar (DuPont), Vectran (Kuraray Co., Ltd.), Orthofabric, and Tyvek (DuPont)) that are candidates for advanced spacesuits. Three of the four new candidate fabrics (all but Vectran) were effective at keeping the dust from penetrating to layers beneath. In the cases of Kevlar and Orthofabric this was accomplished by the addition of a silicone layer. In the case of Tyvek, the paper structure was dense enough to block dust transport. The least abrasive damage was suffered by the Tyvek. This was thought to be due in large part to its non-woven paper structure. The woven structures were all abraded where the top of the weave was struck by the abrasive. Of these, the Orthofabric suffered the least wear, with both Vectran and Kevlar suffering considerably more extensive filament breakage.

  20. Effect of Native Oxide Film on Commercial Magnesium Alloys Substrates and Carbonate Conversion Coating Growth and Corrosion Resistance

    Science.gov (United States)

    Feliu, Sebastián; Samaniego, Alejandro; Bermudez, Elkin Alejandro; El-Hadad, Amir Abdelsami; Llorente, Irene; Galván, Juan Carlos

    2014-01-01

    Possible relations between the native oxide film formed spontaneously on the AZ31 and AZ61 magnesium alloy substrates with different surface finish, the chemistry of the outer surface of the conversion coatings that grows after their subsequent immersion on saturated aqueous NaHCO3 solution treatment and the enhancement of corrosion resistance have been studied. The significant increase in the amount of aluminum and carbonate compounds on the surface of the conversion coating formed on the AZ61 substrate in polished condition seems to improve the corrosion resistance in low chloride ion concentration solutions. In contrast, the conversion coatings formed on the AZ31 substrates in polished condition has little effect on their protective properties compared to the respective as-received surface. PMID:28788582

  1. DEPENDENCE OF DISTRIBUTION FUNCTION OF COMMERCIAL DAMAGES DUE TO POSSIBLE EARTHQUAKES ON THE CLASS OF SEISMIC RESISTANCE OF A BUILDING

    Directory of Open Access Journals (Sweden)

    Hanzada R. Zajnulabidova

    2017-01-01

    Full Text Available Abstract. Objectives To determine the damage probability of earthquakes of different intensities on the example of a real projected railway station building having a framework design scheme based on the density function of damage distribution. Methods Uncertainty, always existing in nature, invalidates a deterministic approach to the assessment of territorial seismic hazards and, consequently, seismic risk. In this case, seismic risk assessment can be carried out on a probabilistic basis. Thus, the risk will always be there, but it must be minimised. The task of optimising the reinforcement costs is solved by using the density distribution function for seismic effects of varying intensity, taking into account the degree of building responsibility. Results The distribution functions of the expected damage for a building with a reinforced concrete frame located in a highly seismic region with a repetition of 9-point shocks every 500 years and 10-point shocks once every 5000 years are constructed. A significant effect of the seismic resistance class of a building on the form of the distribution functions is shown. For structures of a high seismic resistance class, not only is the seismic risk reduced, but also the variance of the expected damage. From the graphs obtained, it can be seen that the seismic resistance class significantly affects the damage distribution. At a probability of 0.997, the expected damage for a non-reinforced building will exceed 43%; for a reinforced one it is only 10%. It also follows from the graphs that the variance of the damage magnitude decreases with the growth of the seismic resistance class of the building. This fact is an additional incentive for investing in antiseismic reinforcement of buildings. Conclusion The study shows the expediency of working with the damage density distribution function when managing seismic risk. In this case, it becomes possible to strengthen the building with a specified probability of

  2. Surface Analysis of Metal Materials After Water Jet Abrasive Machining

    Directory of Open Access Journals (Sweden)

    Pavel Polák

    2015-01-01

    Full Text Available In this article, we deal with a progressive production technology using the water jet cutting technology with the addition of abrasives for material removal. This technology is widely used in cutting various shapes, but also for the technology of machining such as turning, milling, drilling and cutting of threads. The aim of this article was to analyse the surface of selected types of metallic materials after abrasive machining, i.e. by assessing the impact of selected machining parameters on the surface roughness of metallic materials.

  3. The measurement in vitro of dentine abrasion by toothpastes.

    Science.gov (United States)

    Vicentini, Bruna Carvalho; Braga, Sheila Regina Maia; Sobral, Maria Angela Pita

    2007-10-01

    To investigate the in vitro dentine wear after tooth brushing with a range of nine toothpastes. 70 bovine dentine blocks (aproximately 1 cm long) were used. Specimens were brushed in vitro with toothpastes with a range of abrasive. All the specimens were submitted to 10,000 brushing cycles with a 200g load. Initial and final weight and profile data were obtained using an analytical scale and a profile projector respectively. Significant differences between the test products were found (p whitening toothpastes. This study demonstrated that the type of toothpaste abrasive can contribute to dentine wear.

  4. Design and manufacturing of abrasive jet machine for drilling operation

    Directory of Open Access Journals (Sweden)

    Mittal Divyansh

    2016-01-01

    Full Text Available Wide application of Abrasive Jet Machine (AJM is found in machining hard and brittle materials. Machining of brittle materials by AJM is due to brittle fracture and removal of micro chips from the work piece. Embedment of the abrasive particles in the brittle materials results in decrease of machining efficiency. In this paper design and manufacturing of AJM has been presented. Various parts of AJM have been designed using ANSYS 16.2 software. The parts are then manufactured indigenously as per designed parameters. The machine fabricated in this work will be used further for process optimization of AJM parameters for machining of glass and ceramics.

  5. Safely coupling livestock and crop production systems: how rapidly do antibiotic resistance genes dissipate in soil following a commercial application of swine or dairy manure?

    Science.gov (United States)

    Marti, Romain; Tien, Yuan-Ching; Murray, Roger; Scott, Andrew; Sabourin, Lyne; Topp, Edward

    2014-05-01

    Animal manures recycled onto crop production land carry antibiotic-resistant bacteria. The present study evaluated the fate in soil of selected genes associated with antibiotic resistance or genetic mobility in field plots cropped to vegetables and managed according to normal farming practice. Referenced to unmanured soil, fertilization with swine or dairy manure increased the relative abundance of the gene targets sul1, erm(B), str(B), int1, and IncW repA. Following manure application in the spring of 2012, gene copy number decayed exponentially, reaching background levels by the fall of 2012. In contrast, gene copy number following manure application in the fall of 2012 or spring of 2013 increased significantly in the weeks following application and then declined. In both cases, the relative abundance of gene copy numbers had not returned to background levels by the fall of 2013. Overall, these results suggest that under conditions characteristic of agriculture in a humid continental climate, a 1-year period following a commercial application of raw manure is sufficient to ensure that an additional soil burden of antibiotic resistance genes approaches background. The relative abundance of several gene targets exceeded background during the growing season following a spring application or an application done the previous fall. Results from the present study reinforce the advisability of treating manure prior to use in crop production systems.

  6. An Industrial Perspective on Environmentally Assisted Cracking of Some Commercially Used Carbon Steels and Corrosion-Resistant Alloys

    Science.gov (United States)

    Ashida, Yugo; Daigo, Yuzo; Sugahara, Katsuo

    2017-08-01

    Commercial metals and alloys like carbon steels, stainless steels, and nickel-based super alloys frequently encounter the problem of environmentally assisted cracking (EAC) and resulting failure in engineering components. This article aims to provide a perspective on three critical industrial applications having EAC issues: (1) corrosion and cracking of carbon steels in automotive applications, (2) EAC of iron- and nickel-based alloys in salt production and processing, and (3) EAC of iron- and nickel-based alloys in supercritical water. The review focuses on current industrial-level understanding with respect to corrosion fatigue, hydrogen-assisted cracking, or stress corrosion cracking, as well as the dominant factors affecting crack initiation and propagation. Furthermore, some ongoing industrial studies and directions of future research are also discussed.

  7. Simulation of abrasive flow machining process for 2D and 3D mixture models

    Science.gov (United States)

    Dash, Rupalika; Maity, Kalipada

    2015-12-01

    Improvement of surface finish and material removal has been quite a challenge in a finishing operation such as abrasive flow machining (AFM). Factors that affect the surface finish and material removal are media viscosity, extrusion pressure, piston velocity, and particle size in abrasive flow machining process. Performing experiments for all the parameters and accurately obtaining an optimized parameter in a short time are difficult to accomplish because the operation requires a precise finish. Computational fluid dynamics (CFD) simulation was employed to accurately determine optimum parameters. In the current work, a 2D model was designed, and the flow analysis, force calculation, and material removal prediction were performed and compared with the available experimental data. Another 3D model for a swaging die finishing using AFM was simulated at different viscosities of the media to study the effects on the controlling parameters. A CFD simulation was performed by using commercially available ANSYS FLUENT. Two phases were considered for the flow analysis, and multiphase mixture model was taken into account. The fluid was considered to be a

  8. Experimental Investigation on the Material Removal of the Ultrasonic Vibration Assisted Abrasive Water Jet Machining Ceramics

    Directory of Open Access Journals (Sweden)

    Tao Wang

    2017-01-01

    Full Text Available The ultrasonic vibration activated in the abrasive water jet nozzle is used to enhance the capability of the abrasive water jet machinery. The experiment devices of the ultrasonic vibration assisted abrasive water jet are established; they are composed of the ultrasonic vibration producing device, the abrasive supplying device, the abrasive water jet nozzle, the water jet intensifier pump, and so on. And the effect of process parameters such as the vibration amplitude, the system working pressure, the stand-off, and the abrasive diameter on the ceramics material removal is studied. The experimental result indicates that the depth and the volume removal are increased when the ultrasonic vibration is added on abrasive water jet. With the increase of vibration amplitude, the depth and the volume of material removal are also increased. The other parameters of the ultrasonic vibration assisted abrasive water jet also have an important role in the improvement of ceramic material erosion efficiency.

  9. Numerical simulation study on erosion mechanism of pre-mixed abrasive water jet

    National Research Council Canada - National Science Library

    Meng, Junqing; Wei, Qingen; Ma, Yechao

    2017-01-01

    ... to simulate single abrasive particle of rock erosion rule and analyze the influence of different particle size, different grinding particle impact velocity, different abrasive particle shape on rock erosion effect...

  10. A commercial line probe assay for the rapid detection of rifampicin resistance in Mycobacterium tuberculosis: a systematic review and meta-analysis

    Directory of Open Access Journals (Sweden)

    Kalantri Shriprakash

    2005-07-01

    Full Text Available Abstract Background Mycobacterium tuberculosis is a leading cause of death worldwide. In multi-drug resistant tuberculosis (MDR-TB infectiousness is frequently prolonged, jeopardizing efforts to control TB. The conventional tuberculosis drug susceptibility tests are sensitive and specific, but they are not rapid. The INNO-LiPA Rif. TB ® (LiPA is a commercial line probe assay designed to rapidly detect rifampicin resistance, a marker of MDR-TB. Although LiPA has shown promising results, its overall accuracy has not been systematically evaluated. Methods We did a systematic review and meta-analysis to evaluate the accuracy of LiPA for the detection of rifampicin-resistant tuberculosis among culture isolates and clinical specimens. We searched Medline, Embase, Web of Science, BIOSIS, and Google Scholar, and contacted authors, experts and the manufacturer. Fifteen studies met our inclusion criteria. Of these, 11 studies used culture isolates, one used clinical specimens, and three used both. We used a summary receiver operating characteristic (SROC curve and Q* index to perform meta-analysis and summarize diagnostic accuracy. Results Twelve of 14 studies that applied LiPA to isolates had sensitivity greater than 95%, and 12 of 14 had specificity of 100%. The four studies that applied LiPA directly to clinical specimens had 100% specificity, and sensitivity that ranged between 80% and 100%. The SROC curve had an area of 0.99 and Q* of 0.97. Conclusion LiPA is a highly sensitive and specific test for the detection of rifampicin resistance in culture isolates. The test appears to have relatively lower sensitivity when used directly on clinical specimens. More evidence is needed before LiPA can be used to detect MDR-TB among populations at risk in clinical practice.

  11. Assessment of mechanical and three-body abrasive wear peculiarity ...

    Indian Academy of Sciences (India)

    by using VIKOR method. Keywords. Mechanical property; three-body abrasive wear; Taguchi methodology; surface morphology; VIKOR ... wear behaviour of filled epoxy composite systems and concluded that low wt% of boron ... process, which was supported by SEM (scanning electron microscope) studies (reduced ...

  12. Development and Performance Evaluation of an Abrasive Wear ...

    African Journals Online (AJOL)

    The wear of tillage tools is a major source of economic constraints to local farmers. Estimating wear in the field is time consuming and expensive. Abrasive wear testing machines developed in advanced countries are not available in Ghana. This makes the study of wear related problems at laboratory levels difficult in the ...

  13. Abrasive wear behaviour of bio-active glass ceramics containing ...

    Indian Academy of Sciences (India)

    Unknown

    Abstract. In this study, abrasive wear behaviour of bio-active glass ceramic materials produced with two different processes is studied. Hot pressing process and conventional casting and controlled crystallization process were used to produce bio-active ceramics. Fracture toughness of studied material was calculated by.

  14. Review of Artificial Abrasion Test Methods for PV Module Technology

    Energy Technology Data Exchange (ETDEWEB)

    Miller, David C. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Muller, Matt T. [National Renewable Energy Lab. (NREL), Golden, CO (United States); Simpson, Lin J. [National Renewable Energy Lab. (NREL), Golden, CO (United States)

    2016-08-01

    This review is intended to identify the method or methods--and the basic details of those methods--that might be used to develop an artificial abrasion test. Methods used in the PV literature were compared with their closest implementation in existing standards. Also, meetings of the International PV Quality Assurance Task Force Task Group 12-3 (TG12-3, which is concerned with coated glass) were used to identify established test methods. Feedback from the group, which included many of the authors from the PV literature, included insights not explored within the literature itself. The combined experience and examples from the literature are intended to provide an assessment of the present industry practices and an informed path forward. Recommendations toward artificial abrasion test methods are then identified based on the experiences in the literature and feedback from the PV community. The review here is strictly focused on abrasion. Assessment methods, including optical performance (e.g., transmittance or reflectance), surface energy, and verification of chemical composition were not examined. Methods of artificially soiling PV modules or other specimens were not examined. The weathering of artificial or naturally soiled specimens (which may ultimately include combined temperature and humidity, thermal cycling and ultraviolet light) were also not examined. A sense of the purpose or application of an abrasion test method within the PV industry should, however, be evident from the literature.

  15. Assessment of Rail Seat Abrasion Patterns and Environment

    Science.gov (United States)

    2012-05-01

    Rail seat abrasion (RSA) of concrete ties is manifested by the loss of material under the rail seat area and, in extreme cases, results in loss of rail clip holding power, reverse rail cant, and gauge widening. RSA was measured in several curves on t...

  16. Hardness and elasticity of abrasive particles measured by instrumented indentation

    Czech Academy of Sciences Publication Activity Database

    Hvizdoš, P.; Zeleňák, Michal; Hloch, Sergej

    2016-01-01

    Roč. 8, č. 1 (2016), s. 869-871 ISSN 1805-0476 Institutional support: RVO:68145535 Keywords : abrasive * garnet * hardness * elasticity * instrumental indentation Subject RIV: JQ - Machines ; Tools http://www.mmscience.eu/content/file/archives/MM_Science_201601.pdf

  17. Investigating the influence of sand particle properties on abrasive wear behaviour

    NARCIS (Netherlands)

    Woldman, M.; van der Heide, Emile; Schipper, Dirk J.; Tinga, Tiedo; Masen, Marc Arthur

    2012-01-01

    Abrasion by sand particles is an important factor causing excessive wear in machines operating in sandy environments. To prevent such machines from failing, knowledge about the abrasive wear process is required. This work focuses on the relation between abrasive particle properties and the wear they

  18. Abrasions and lameness in piglets born in different farrowing systems with different types of floor

    Directory of Open Access Journals (Sweden)

    Mattsson Sigbrit

    2008-09-01

    Full Text Available Abstract Background The quality of the floor is essential to the welfare of piglets as abrasions often are recorded in newborn piglets, and such lesions may lead to lameness. Apart from animal suffering, lameness contributes to losses in form of dead piglets, decreased growth, and increased use of antibiotics and manual labour. Methods In a herd with three different farrowing systems, 37 litters (390 piglets were studied until the age of 3 weeks with respect to presence of skin wounds and abrasions. Lameness was registered until the age of 7 weeks. Eight lame piglets were sacrificed before medical treatment and subjected to necropsy including histopathological and microbiological examinations. Isolates of streptococci, staphylococci and E. coli were tested with respect to antimicrobial resistance. Mastitis was observed in ten sows. Results The most severe abrasions at carpus and soles were seen in the system with a new solid concrete floor with a slatted floor over the dunging area. The lowest magnitude was observed in the deep litter system with peat. Sole bruising was more common in the systems with concrete floor compared to the deep litter system with peat, and the differce in prevalence was significant at all examination days. The lesions decreased with time and about 75% of the treatments for lameness were performed during the first three weeks of life. The overall prevalence of lameness was highest in the system with new solid concrete floor with a slatted floor over the dunging area (9.4% followed by the old solid concrete floor (7.5%. A lower (p Conclusion There were large differences in the prevalence of abrasions and lameness between the floor types. The deep litter system with peat provided a soft and good floor for piglets. The overall prevalence of lameness was only diagnosed in every fourth litter in that system compared to in every second litter in the systems with concrete floor. In contrast, the incidence of mastitis in the

  19. In vitro cleaning, abrasion and fluoride efficacy of a new silica based whitening toothpaste containing blue covarine.

    Science.gov (United States)

    Joiner, Andrew; Philpotts, Carole J; Ashcroft, Alex T; Laucello, Massimo; Salvaderi, Angela

    2008-01-01

    To investigate the stain removal ability, abrasivity towards enamel and dentine, and fluoride efficacy of a new silica based blue covarine whitening toothpaste in vitro. Stain removal was assessed by brushing artificially stained bovine specimens with slurries of either the new toothpaste or one of two whitening products or a non-whitening silica product. Toothpaste abrasivity was assessed by brushing enamel/dentine specimens with slurries of either the new toothpaste, a whitening toothpaste or a non-whitening toothpaste and measuring the wear via a combination of changes in geometry of Knoop indents and surface profilometry. Fluoride efficacy was assessed using remineralisation, demineralisation and fluoride-uptake methods. The in vitro cleaning study showed that the silica based blue covarine whitening toothpaste removed significantly (p whitening toothpaste and was as effective as the two marketed silica based whitening toothpastes. This enhanced tooth whitening benefit did not give rise to a concomitant statistically significant increase in the level of wear to enamel and dentine compared to the non-whitening silica based toothpaste. The fluoride efficacy was superior to a non-fluoridated control and was as effective as a clinically tested formulation containing the same fluoride source. The studies show that the new whitening toothpaste is effective in extrinsic stain removal, does not have an undue degree of abrasivity to enamel or dentine compared to other relevant commercially available products, and is an efficacious source of fluoride.

  20. A correlation for predicting the abrasive water jet cutting depth for natural stones

    Directory of Open Access Journals (Sweden)

    Irfan C. Engin

    2012-09-01

    Full Text Available The abrasive water jet (AWJ cutting method has been used widely for the cutting and processing of materials because of its cool, damage-free, and precise cutting technique. Nowadays, the use of AWJ cutting in the natural stone industry is increasing. However, the effectiveness of AWJ cutting of natural stones is dependent on the rock properties and machine operating parameters. In this study, injection-type AWJ cutting was applied to 42 different types of natural stones to investigate the effects of rock properties and operating parameters on the cutting depth. Shore hardness, Bohme surface abrasion resistance and the density of the rocks were the most significant rock properties affecting the cutting depth. The working pump pressure and traverse velocity were the most significant operating parameters affecting cutting, as has been shown previously. The relationships between the rock properties or operating parameters and the cutting depth were evaluated using multiple linear and nonlinear regression analyses, and estimation models were developed. Some of the models included only rock properties under fixed operating conditions, and others included both rock properties and operating parameters to predict cutting depth. The models allow for the preselection of particular operating parameters for the cutting of specific rocks types. The prediction of cutting depth is a valuable tool for the controlled surface machining of rock materials.

  1. Analysis of abrasive wear behavior of PTFE composite using Taguchi’s technique

    Directory of Open Access Journals (Sweden)

    Yusuf Şahin

    2015-12-01

    Full Text Available Polymeric composites are widely used for structural, aerospace, and automobile sectors due to their good combination of high specific strength and specific modulus. These two main characteristics make these materials attractive, compared to conventional materials like metal or alloy ones. Some of their typical benefits include easy processing, corrosion resistance, low friction, and damping of noise and vibrations. Wear behavior of Polytetrafluoroethylenes (PTFE and its composites including glass-filled composites and carbon-filled composites are investigated using a pin-on-disc configuration. A plan of experiments in terms of Taguchi technique is carried out to acquire data in controlled way. An orthogonal array (L9 and the analysis of variance are employed to investigate the influence of process parameters on the wear of these composites. Volume loss increased with abrasive size, load, and distance. Furthermore, specific wear rate decreased with increasing grit size, load, sliding distance, whereas, slightly with compressive strength. Optimal process parameters, which minimize the volume loss, were the factor combinations of L1, G3, D1, and C3. Confirmation experiments were conducted to verify the optimal testing parameters. It was found that in terms of volume loss, there was a good agreement between the estimated and the experimental value of S/N ratio with an error of 1.604%. Moreover, abrasive size, load, and sliding distance exerted a great effect on the specific wear rate, at 51.14, 27.77, and 14.70%, respectively.

  2. A new methodology for hydro-abrasive erosion tests simulating penstock erosive flow

    Science.gov (United States)

    Aumelas, V.; Maj, G.; Le Calvé, P.; Smith, M.; Gambiez, B.; Mourrat, X.

    2016-11-01

    Hydro-abrasive resistance is an important property requirement for hydroelectric power plant penstock coating systems used by EDF. The selection of durable coating systems requires an experimental characterization of coating performance. This can be achieved by performing accelerated and representative laboratory tests. In case of severe erosion induced by a penstock flow, there is no suitable method or standard representative of real erosive flow conditions. The presented study aims at developing a new methodology and an associated laboratory experimental device. The objective of the laboratory apparatus is to subject coated test specimens to wear conditions similar to the ones generated at the penstock lower generatrix in actual flow conditions. Thirteen preselected coating solutions were first been tested during a 45 hours erosion test. A ranking of the thirteen coating solutions was then determined after characterisation. To complete this first evaluation and to determine the wear kinetic of the four best coating solutions, additional erosion tests were conducted with a longer duration of 216 hours. A comparison of this new method with standardized tests and with real service operating flow conditions is also discussed. To complete the final ranking based on hydro-abrasive erosion tests, some trial tests were carried out on penstock samples to check the application method of selected coating systems. The paper gives some perspectives related to erosion test methodologies for materials and coating solutions for hydraulic applications. The developed test method can also be applied in other fields.

  3. The Comparative Effect of Sugarcane Juice on the Abrasion-Corrosion Behavior of Fe-Cr-B Electric Arc Sprayed and Fe-Cr-C Weld Coatings

    Science.gov (United States)

    Buchanan, Vernon E.

    2012-02-01

    Abrasion-corrosion tests were conducted on two commonly Fe-Cr-C shielded metal arc welding (SMAW) hardfacings used in the sugar industry and an arc sprayed Fe-Cr-based coating. The tests were performed on a modified block-on-ring tester with the coatings sliding against compressed sugarcane fiber in the presence of abrasive slurry. The findings showed that, in the presence of sugarcane juice and sand slurry, the SMAW coatings had similar wear performance while the abrasive wear of the arc-sprayed coating was superior to the SMAW coatings. In the presence of a neutral solution, the material loss from the arc-sprayed coating was similar to that obtained in the sugarcane juice while the SMAW coatings showed a marked decrease; this demonstrated that the arc-sprayed coating was more desirable in an abrasive-corrosion environment. The study also showed that the resistance to material does not follow the expected trend, in which wear resistance increases with increasing hardness.

  4. The effect of debris accumulation on and filter resistance to airflow for four commercially available vacuum cleaners.

    Science.gov (United States)

    Heitbrink, William A; Santalla-Elias, Javier

    2009-06-01

    Mortar removal with right-angle grinders can cause excessive exposure to respirable crystalline silica. To control this dust exposure, vacuum cleaners need to exhaust 2.3 m(3)/min (80 cubic feet per minute) from the grinder's exhaust hood. Maintaining this airflow while collecting as much as 15.9 kg (35 lb) of debris in the vacuum cleaner has been problematic. A laboratory study was conducted to evaluate how mortar debris affects vacuum cleaner airflow and filter pressure loss. Four vacuum cleaners were tested. Two of the vacuum cleaners used vacuum cleaner bags as a prefilter; the other two vacuum cleaners used cyclones to reduce the amount of debris that reaches the filter. Test debris was collected by a masonry restoration contractor during actual mortar removal using a grinder fitted with a hood. The hood is attached to a vacuum cleaner with cyclonic pre-separation. The vacuum cleaner fan curves were obtained experimentally to learn how pressure loss affects vacuum cleaner airflows. Then, 15.9 kg (35 lb) of mortar removal debris was sucked into the vacuum cleaner in 2.27-kg (5-lb) increments. Before and after adding each 2.27-kg (5-lb) increment of debris, vacuum cleaner airflows were measured with a venturi meter, and vacuum cleaner static pressures were measured at the inlet to the vacuum cleaner motor, and before and after each filter. The vacuum cleaners equipped with cyclonic pre-separation were unaffected by the mass of debris collected in the vacuum cleaner and were able to maintain airflows in excess of 1.98 m(3)/min (70 cfm) throughout the testing program. As debris accumulated in the vacuum cleaners that used bags, airflow decreased from 2.3 m(3)/min (80 cfm) to as little as 0.85 m(3)/min (30 cfm). This airflow loss is caused by the increased airflow resistance of the bags that increased from less 0.03 kPa/m(3)/min (0.1 inches of water per cfm) to 16.7 kPa/m(3)/min (1.9 inches of water/cfm). Apparently, vacuum cleaners using bags should be used in

  5. Resistência de variedades comerciais de cana-de-açúcar ao agente causal do raquitismo-da-soqueira Resistance of sugarcane commercials cultivars to causal agent of ratoon stunting disease

    Directory of Open Access Journals (Sweden)

    Paulo Roberto Gagliardi

    2009-07-01

    Full Text Available O raquitismo-da-soqueira (RSD, causado pela bactéria Leifsonia xyli subsp. xyli, é uma das mais importantes doenças da cana-de-açúcar nas regiões produtoras do mundo. O presente trabalho teve como objetivo avaliar o grau de resistência de 10 variedades comerciais RB de cana-de-açúcar mais a variedade CB 49-260, a qual foi incluída como padrão suscetível. O trabalho visou avaliar os danos amostrados em campo pelo peso das parcelas em função da relação entre a produtividade de parcelas inoculadas e não inoculadas artificialmente com a bactéria. Os resultados mostraram que as variedades RB 72 454, RB 83 5486, RB 86 7515, RB 92 5211, RB 92 5268, RB 92 5345, RB 92 8064 e a variedade padrão CB 49-260 comportaram-se como variedades suscetíveis. A variedade RB 85 5156 comportou-se como de resistência intermediária e apenas as variedades RB 85 5453 e RB 85 5536 comportaram-se como tolerantes.Ratoon stunting disease (RSD caused by bacteria Leifsonia xyli subsp. xyli is one of the most economically important disease of sugarcane worldwide. The present survey had objective to evaluate the resistance of 10 RB commercial cultivars of sugarcane including CB 49-260 as a susceptible standard. The study evaluated the correlating the damages presented for overhauls productivity of inoculate and non inoculate parcels with the bacteria. The results showed that varieties RB 72 454, RB 83 5486, RB 86 7515, RB 92 8064, RB 92 5211, RB 92 5345 and RB 92 5268 were susceptible. RB 85 5156 had a intermediary resistance and varieties RB 85 5453 and RB 85 5536 both showed tolerant behavior.

  6. Prevalence and Antibiotic Resistance of Non-typhoidal Salmonella Isolated from Raw Chicken Carcasses of Commercial Broilers and Spent Hens in Tai’an, China

    Directory of Open Access Journals (Sweden)

    Song Li

    2017-10-01

    Full Text Available The present study was aimed to determine the prevalence and characteristics of Salmonella isolated from meat samples of commercial broilers (CB and spent hens (SH. Between March and June 2016, 200 retail raw chicken carcasses (100 from CB and 100 from SH were obtained from local supermarkets in Tai’an city of China, and Salmonella isolates were then analyzed for antibiotic resistance, serotype, β-lactamase genes, and the presence of class 1 integron. Forty Salmonella strains were obtained in this study (CB: 21/100, 21%; SH: 19/100, 19%. Three serotypes were identified in 40 Salmonella, and S. Enteritidis (CB: 15/21, 71.4%; SH: 10/19, 52.6% was the dominant serotype, followed by S. Typhimurium (CB: 4/21, 19%; SH: 6/19, 31.6% and S. Derby (CB: 2/21, 9.5%; SH: 3/19, 15.8%. Among 21 Salmonella isolated from CB, high antibiotic resistance rates were found for ampicillin (20/21, 95.2%, nalidixic acid (18/21, 85.7%, cefotaxime (17/21, 81%, and tetracycline (13/21, 61.9%; class 1 integron was observed in seven isolates (7/21, 33.3%, and gene cassettes included an empty integron (0.15 kb, n = 1, aadA2 (1.2 kb, n = 3, drfA1-aadA1 (1.4 kb, n = 1, and drfA17-aadA5 (1.7 kb, n = 2; blaTEM-1 was the dominant β-lactamase gene (21/21, 100%, followed by blaCTX-M-55 (7/21, 33.3%. Among 19 Salmonella isolated from SH, high antibiotic resistance rates were found for nalidixic acid (19/19, 100%, tetracycline (19/19, 100%, ampicillin (18/19, 94.7%, and ciprofloxacin (13/19, 68.4%; class 1 integron was observed in two isolates (2/19, 10.5%, and gene cassettes included drfA17-aadA5 (1.7 kb, n = 1 and drfA1-aadA1 (1.4 kb, n = 1; blaTEM-1 was the dominant β-lactamase gene (19/19, 100%, followed by blaCTX-M-55 (2/19, 10.5% and blaCMY-2 (1/19, 5.3%. Collectively, antibiotic-resistant Salmonella can be widely detected in retail raw chicken carcasses of CB and SH, and therefore can pose a serious risk to public health.

  7. Dental abrasion as a cutting process.

    Science.gov (United States)

    Lucas, Peter W; Wagner, Mark; Al-Fadhalah, Khaled; Almusallam, Abdulwahab S; Michael, Shaji; Thai, Lidia A; Strait, David S; Swain, Michael V; van Casteren, Adam; Renno, Waleed M; Shekeban, Ali; Philip, Swapna M; Saji, Sreeja; Atkins, Anthony G

    2016-06-06

    A mammalian tooth is abraded when a sliding contact between a particle and the tooth surface leads to an immediate loss of tooth tissue. Over time, these contacts can lead to wear serious enough to impair the oral processing of food. Both anatomical and physiological mechanisms have evolved in mammals to try to prevent wear, indicating its evolutionary importance, but it is still an established survival threat. Here we consider that many wear marks result from a cutting action whereby the contacting tip(s) of such wear particles acts akin to a tool tip. Recent theoretical developments show that it is possible to estimate the toughness of abraded materials via cutting tests. Here, we report experiments intended to establish the wear resistance of enamel in terms of its toughness and how friction varies. Imaging via atomic force microscopy (AFM) was used to assess the damage involved. Damage ranged from pure plastic deformation to fracture with and without lateral microcracks. Grooves cut with a Berkovich diamond were the most consistent, suggesting that the toughness of enamel in cutting is 244 J m(-2), which is very high. Friction was higher in the presence of a polyphenolic compound, indicating that this could increase wear potential.

  8. Superior quality diamond heel inserts improve cutting structure and seal life in abrasive and directional applications

    Energy Technology Data Exchange (ETDEWEB)

    Cobb, Tyler; Scott, Dan; Nelms, Derek [Society of Petroleum Engineers (United States)

    2011-07-01

    In the oil and gas industry, continuous improvements over the last century have led to the development of increasingly efficient drilling equipment. Among the new technologies is the polycrystalline diamond compact bit which has become more efficient than roller cone bits for several applications; the utilization of roller cone bits is now restricted to tough applications such as directional drilling and drilling through hard and abrasive formations. The aim of this paper is to present the development of improved roller cone bits using new designs and diamond inserts of superior quality. Two case studies on the use of improved roller cone bits are presented herein. Results showed that the novel diamond inserts combined with the design improvements provide better wear resistance. This paper demonstrated that roller cone bits have achieved greater reliability and longevity thanks to the new generation of diamond inserts and to design improvements.

  9. Dynamics Performance and Abrasive Wear of the Automotive Drive Shaft

    Directory of Open Access Journals (Sweden)

    Jian Mao

    2014-06-01

    Full Text Available An automotive drive shaft is used in a front drive transmission vehicle for transmitting rotary movement from the gearbox output shaft to the wheels with a constant velocity. This paper presents the kinematic model of ball joint and tripod joint with consideration of clearance and proposes a simplified dynamics model of the drive shaft. The simulation of the dynamics model is given by the measured data. Also, the abrasive wear of the ball type joint is tested on the experimental setup with consideration of full loading. The results show that the dynamics of the motion will be affected by the clearance when the loading changes its direction. The motion will be stable due to the damping. It can be found that the abrasive wear of ball joint largely depends on the relative sliding velocity from the experiments. This will probably affectthe dynamics performance and the impact force, which will also cause the other type of failures.

  10. Design of a new abrasive slurry jet generator

    Science.gov (United States)

    Wang, F. C.; Shi, L. L.; Guo, C. W.

    2017-12-01

    With the advantages of a low system working pressure, good jet convergence and high cutting quality, abrasive slurry jet (ASJ) has broad application prospects in material cutting and equipment cleaning. Considering that the generator plays a crucial role in ASJ system, the paper designed a new type ASJ generator using an electric oil pump, a separate plunger cylinder, and a spring energized seal. According to the determining of structure shape, size and seal type, a new ASJ generator has been manufactured out and tested by a series of experiments. The new generator separates the abrasive slurry from the dynamic hydraulic oil, which can improve the service life of the ASJ system. And the new ASJ system can reach 40 MPa and has good performance in jet convergence, which deserves to popularization and application in materials machining.

  11. Removal of enamel caries with an air abrasion powder.

    Science.gov (United States)

    Neuhaus, Klaus W; Ciucchi, Philip; Donnet, Marcel; Lussi, Adrian

    2010-01-01

    This study compared the efficiency of air abrasion on enamel caries with selective enamel powder (SEP) or with alumina powder and a negative and positive control group. Ninety-three extracted molars with non-cavitated incipient enamel lesions were selected. After embedding the roots in resin, each lesion was sectioned perpendicular to the surface and photographed. Each lesion was classified microscopically as having or not having dentin involvement. The lesions were distributed into four groups with an equal number of enamel caries with or without dentin involvement. Each group was treated differently: Group 1 had SEP abrasion, Group 2 had alumina abrasion, Group 3 had sodium bicarbonate abrasion (negative control) and Group 4 had bur treatment (positive control). The surface was rephotographed after treatment. Superimposition of the photographs identified areas of "correct-excavation," "under-excavation" and "over-excavation." There were no statistical differences between lesions treated with or without dentin involvement for Groups 2 through 4. However, in the SEP group, all measured areas were significantly influenced by dentin involvement. In pairwise comparisons, no statistical differences were found between the alumina and bur groups. The SEP group, however, showed statistically significant differences for each area compared to the alumina group in enamel caries without dentin involvement. SEP performed as well as alumina and bur in lesions with dentin involvement. SEP is different in its ablative properties toward caries with dentin involvement or no dentin involvement. In terms of dental treatment, SEP seems to have a diagnostic potential for enamel lesions before operative intervention in patients with high caries risk.

  12. Abrasive Wear of Alloyed Cast Steels Applied for Heavy Machinery

    Directory of Open Access Journals (Sweden)

    Studnicki A.

    2015-03-01

    Full Text Available In the paper the results and analysis of abrasive wear studies were shown for two grades of cast steels: low-alloyed cast steel applied for heavy machinery parts such as housing, covers etc. and chromium cast steels applied for kinetic nodes of pin-sleeve type. Studies were performed using the modified in Department of Foundry pin-on-disc method.

  13. Occlusive dressings and the healing of standardized abrasions.

    Science.gov (United States)

    Beam, Joel W

    2008-01-01

    Acute skin trauma during sport participation, resulting in partial-thickness abrasions, is common. The limited investigations focusing on the acute wound environment and dressing techniques and the subsequent lack of evidence-based standards complicate clinical wound care decisions. To examine the effects of occlusive dressings on healing of standardized, partial-thickness abrasions. Controlled, counterbalanced, repeated-measures design. University laboratory. Sixteen healthy women (n = 10) and men (n = 6). Four standardized, partial-thickness abrasions were inflicted. Film, hydrogel, and hydrocolloid occlusive dressings and no dressing (control) were applied. Participants returned on postwound days 1, 3, 5, 7, 10, and 14 for digital imaging. Wound healing time was measured by change in wound contraction (cm(2)) and change in wound color (chromatic red) and luminance in red, green, and blue color values. Wound contraction, color (chromatic red), and luminance. A day-by-dressing interaction was found for wound contraction, color, and luminance. Post hoc testing indicated that the film and hydrocolloid dressings produced greater wound contraction than the hydrogel and no dressing on days 7 and 10. Film, hydrogel, and hydrocolloid dressings also resulted in greater wound contraction than the control on day 14. Hydrocolloid dressings produced smaller measures of color and greater measures of luminance than no dressing on day 7. Film, hydrogel, and hydrocolloid dressings also resulted in smaller measures of color and greater measures of luminance compared with no dressing on days 10 and 14. When compared with the control (no dressing), the film, hydrogel, and hydrocolloid occlusive dressings were associated with a faster healing rate of partial-thickness abrasions across time measured by wound contraction, color, and luminance. Overall, these data indicate that occlusive dressings were more effective in healing than no dressing was.

  14. Abrasion, Erosion and Cavitation Erosion Wear Properties of Thermally Sprayed Alumina Based Coatings

    Directory of Open Access Journals (Sweden)

    Ville Matikainen

    2014-01-01

    Full Text Available Thermally-sprayed alumina based materials, e.g., alumina-titania (Al2O3-TiO2, are commonly applied as wear resistant coatings in industrial applications. Properties of the coatings depend on the spray process, powder morphology, and chemical composition of the powder. In this study, wear resistant coatings from Al2O3 and Al2O3-13TiO2 powders were sprayed with plasma and high-velocity oxygen-fuel (HVOF spray processes. Both, fused and crushed, and agglomerated and sintered Al2O3-13TiO2 powders were studied and compared to pure Al2O3. The coatings were tested for abrasion, erosion, and cavitation resistances in order to study the effect of the coating structure on the wear behavior. Improved coating properties were achieved when agglomerated and sintered nanostructured Al2O3-13TiO2 powder was used in plasma spraying. Coatings with the highest wear resistance in all tests were produced by HVOF spraying from fused and crushed powders.

  15. Comparing the Air Abrasion Cutting Efficacy of Dentine Using a Fluoride-Containing Bioactive Glass versus an Alumina Abrasive: An In Vitro Study

    Directory of Open Access Journals (Sweden)

    Melissa H. X. Tan

    2015-01-01

    Full Text Available Air abrasion as a caries removal technique is less aggressive than conventional techniques and is compatible for use with adhesive restorative materials. Alumina, while being currently the most common abrasive used for cutting, has controversial health and safety issues and no remineralisation properties. The alternative, a bioactive glass, 45S5, has the advantage of promoting hard tissue remineralisation. However, 45S5 is slow as a cutting abrasive and lacks fluoride in its formulation. The aim of this study was to compare the cutting efficacy of dentine using a customised fluoride-containing bioactive glass Na0SR (38–80 μm versus the conventional alumina abrasive (29 μm in an air abrasion set-up. Fluoride was incorporated into Na0SR to enhance its remineralisation properties while strontium was included to increase its radiopacity. Powder outflow rate was recorded prior to the cutting tests. Principal air abrasion cutting tests were carried out on pristine ivory dentine. The abrasion depths were quantified and compared using X-ray microtomography. Na0SR was found to create deeper cavities than alumina (p<0.05 despite its lower powder outflow rate and predictably reduced hardness. The sharper edges of the Na0SR glass particles might improve the cutting efficiency. In conclusion, Na0SR was more efficacious than alumina for air abrasion cutting of dentine.

  16. Macular Hole Closure With Internal Limiting Membrane Abrasion Technique.

    Science.gov (United States)

    Mahajan, Vinit B; Chin, Eric K; Tarantola, Ryan M; Almeida, David R P; Somani, Riz; Boldt, H Culver; Folk, James C; Gehrs, Karen M; Russell, Stephen R

    2015-06-01

    Internal limiting membrane (ILM) abrasion is an alternative surgical technique for successful full-thickness macular hole (MH) repair. To study the effects of ILM abrasion as an alternative method of MH repair. Retrospective consecutive case series from January 2006 to December 2008. Demographic data and preoperative, intraoperative, and postoperative examination records of all patients were reviewed for patients who underwent ILM abrasion with a diamond-dusted membrane scraper during vitrectomy for MH repair. A total of 100 eyes underwent ILM abrasion as an alternative to traditional ILM peeling. Rate of MH closure and visual acuity (VA) outcomes at 3 months after surgery. Macular hole closure was achieved with a single surgical procedure in 94 of 100 eyes (94.0%; 95% CI, 87.4%-97.8%). Among all patients, the median preoperative VA was 20/100 (range, 20/30 to hand motions; 25th quartile, 20/60; and 75th quartile, 20/160), and the median postoperative VA at 3 months after surgery was 20/60 (range, 20/20 to hand motions; 25th quartile, 20/40; and 75th quartile, 20/100). Among all patients with stage 2 MHs, 30 of 38 patients (78.9%) had at least 2 lines of VA gain: 15 of 23 (65.2%) were phakic, and 15 of 15 (100%) were pseudophakic. Four of 38 patients (10.5%) with stage 2 MHs had at least 2 lines of VA loss, and all were phakic. Among all patients with stage 3 or 4 MHs, 42 of 62 (67.7%) had at least 2 lines of VA gain, of which 30 of 38 (78.9%) were phakic and 22 of 24 (91.7%) were pseudophakic. Six of 62 patients (9.7%) with stage 3 or 4 MHs had at least 2 lines of VA loss: 4 were phakic, and 2 were pseudophakic. In total, 35.0% (95% CI, 25.7%-44.3%) of patients achieved 20/40 vision or better, and 52.0% (95% CI, 42.2%-61.8%) of patients achieved 20/50 vision or better. Abrasion of the ILM with a diamond-dusted membrane scraper at the time of vitrectomy achieves high rates of MH closure. This technique avoids complete removal of the retinal ILM basement membrane

  17. Investigation of the Effect of Tungsten Substitution on Microstructure and Abrasive Wear Performance of In Situ VC-Reinforced High-Manganese Austenitic Steel Matrix Composite

    Science.gov (United States)

    Moghaddam, Emad Galin; Karimzadeh, Neda; Varahram, Naser; Davami, Parviz

    2013-08-01

    Particulate VC-reinforced high-manganese austenitic steel matrix composites with different vanadium and tungsten contents were synthesized by conventional alloying and casting route. Microstructural characterizations showed that the composites processed by in situ precipitation of the reinforcements were composed of V8C7 particulates distributed in an austenitic matrix. It was observed that addition of tungsten to austenite increases work-hardening rate of subsurface layer during pin-on disk wear test. The maximum abrasive wear resistance was achieved at tungsten content equal to 2 wt pct. However, excessive addition of tungsten promoted the formation of W3C phase and reduced the abrasive wear resistance because of decrease in distribution homogeneity and volume fraction of the reinforcing VC particles.

  18. Study of Effect of Impacting Direction on Abrasive Nanometric Cutting Process with Molecular Dynamics

    Science.gov (United States)

    Li, Junye; Meng, Wenqing; Dong, Kun; Zhang, Xinming; Zhao, Weihong

    2018-01-01

    Abrasive flow polishing plays an important part in modern ultra-precision machining. Ultrafine particles suspended in the medium of abrasive flow removes the material in nanoscale. In this paper, three-dimensional molecular dynamics (MD) simulations are performed to investigate the effect of impacting direction on abrasive cutting process during abrasive flow polishing. The molecular dynamics simulation software Lammps was used to simulate the cutting of single crystal copper with SiC abrasive grains at different cutting angles (0o-45o). At a constant friction coefficient, we found a direct relation between cutting angle and cutting force, which ultimately increases the number of dislocation during abrasive flow machining. Our theoretical study reveal that a small cutting angle is beneficial for improving surface quality and reducing internal defects in the workpiece. However, there is no obvious relationship between cutting angle and friction coefficient.

  19. Study of Effect of Impacting Direction on Abrasive Nanometric Cutting Process with Molecular Dynamics.

    Science.gov (United States)

    Li, Junye; Meng, Wenqing; Dong, Kun; Zhang, Xinming; Zhao, Weihong

    2018-01-11

    Abrasive flow polishing plays an important part in modern ultra-precision machining. Ultrafine particles suspended in the medium of abrasive flow removes the material in nanoscale. In this paper, three-dimensional molecular dynamics (MD) simulations are performed to investigate the effect of impacting direction on abrasive cutting process during abrasive flow polishing. The molecular dynamics simulation software Lammps was used to simulate the cutting of single crystal copper with SiC abrasive grains at different cutting angles (0 o -45 o ). At a constant friction coefficient, we found a direct relation between cutting angle and cutting force, which ultimately increases the number of dislocation during abrasive flow machining. Our theoretical study reveal that a small cutting angle is beneficial for improving surface quality and reducing internal defects in the workpiece. However, there is no obvious relationship between cutting angle and friction coefficient.

  20. Wear Behaviour of Iron Matrix Composite Reinforced by ZTA Particles in Impact Abrasion

    Science.gov (United States)

    Qiu, B.; Xing, S. M.; Dong, Q.

    2017-11-01

    Zirconia toughened alumina (ZTA) particles reinforced high chromium cast iron composites (ZTA/Iron composites) were prepared by a two-step processing method, i.e. mixing particles by the molten metal and cohering by high pressure, which based on the squeeze casting process. The impact wear resistance under different impact energies were investigated using dynamically loaded abrasive wear tester at room temperature. For comparison, the wear tests of high chromium cast iron were also carried out under the same conditions. Worn surfaces of the samples were observed under scanning electron microscopy equipped with an energy dispersive detector. The results showed that the composites have better impact wear resistance than that of high Cr cast iron regardless of impact energy level, and the wear resistance of the two materials all decrease with the increase of the impact energy. The main wear mechanisms of the high Cr cast iron were micro-cutting and fatigue peeling, while the wear of composites occurred through micro-cutting of the matrix (lower impact energy) and breaking and shedding of the reinforced particles (higher impact energy).

  1. A Profilometric Study to Assess the Role of Toothbrush and Toothpaste in Abrasion Process

    OpenAIRE

    Sandeep Kumar; Siddharth Kumar Singh; Anjali Gupta; Sayak Roy; Mohit Sareen

    2015-01-01

    Statement of the Problem: Despite of many studies conducted on toothbrushes and toothpaste to find out the culprit for abrasion, there is no clear cut evidence to pin point the real cause for abrasion. Purpose: An in vitro assessment of the role of different types of toothbrushes (soft/ medium/hard) in abrasion process when used in conjunction with and without a dentifrice. Materials and Method: Forty five freshly extracted, sound, human incisor teeth were collected for this study. Enam...

  2. A Profilometric Study to Assess the Role of Toothbrush and Toothpaste in Abrasion Process.

    Science.gov (United States)

    Kumar, Sandeep; Kumar Singh, Siddharth; Gupta, Anjali; Roy, Sayak; Sareen, Mohit; Khajuria, Sarang

    2015-09-01

    Despite of many studies conducted on toothbrushes and toothpaste to find out the culprit for abrasion, there is no clear cut evidence to pin point the real cause for abrasion. An in vitro assessment of the role of different types of toothbrushes (soft/ medium/hard) in abrasion process when used in conjunction with and without a dentifrice. Forty five freshly extracted, sound, human incisor teeth were collected for this study. Enamel specimens of approximately 9 mm(2) were prepared by gross trimming of extracted teeth using a lathe machine (Baldor 340 Dental lathe; Ohio, USA). They were mounted on separate acrylic bases. The specimens were divided into three groups, each group containing 15 mounted specimens. Group 1 specimens were brushed with soft toothbrush; Group 2 brushed with medium toothbrush and Group 3 with hard toothbrush. Initially, all the mounted specimens in each group were brushed using dentifrice and then the same procedure was repeated with water as control. Profilometric readings were recorded pre and post to tooth brushing and the differences in readings served as proxy measure to assess surface abrasion. These values were then compared to each other. Kruskal Wallis and Mann-Whitney U test were performed. The results showed that brushing, with water alone, caused less abrasion than when toothpaste was added (p< 0.008). When brushed with water, the harder toothbrush caused more abrasion (higher Ra-value), but when toothpaste was added, the softer toothbrush caused more abrasion (p< 0.001). Besides supporting the fact that toothpaste is needed to create a significant abrasion, this study also showed that a softer toothbrush can cause more abrasion than harder ones. The flexibility of bristles is only secondary to abrasion process and abrasivity of dentifrice has an important role in abrasion process.

  3. Shoe heel abrasion and its possible biomechanical cause: a transversal study with infantry recruits

    OpenAIRE

    Baumfeld, Daniel; Raduan, Fernando C.; Macedo, Benjamim; Silva, Thiago Alexandre Alves; Baumfeld, Tiago; Favato, Danilo Fabrino; de Andrade, Marco Antonio Percope; Nery, Caio

    2015-01-01

    Background Excessive shoe heel abrasion is of concern to patients and shoe manufacturers, but little scientific information is available about this feature and its possible causes. The purpose of this study was to relate this phenomenon with biomechanical factors that could predispose to shoe heel abrasion. Methods Ninety-seven recruits (median age 25) were enrolled in this study. Shoe abrasion was assessed manually with a metric plastic tape on the posterior part of the heel that comes in co...

  4. Study on planarization machining of sapphire wafer with soft-hard mixed abrasive through mechanical chemical polishing

    Energy Technology Data Exchange (ETDEWEB)

    Xu, Yongchao [Institute of Manufacturing Engineering, Huaqiao University, Xiamen 361021 (China); MOE Engineering Research Center for Brittle Materials Machining, Huaqiao University, Xiamen 361021 (China); Lu, Jing, E-mail: lujing26@hqu.edu.cn [Institute of Manufacturing Engineering, Huaqiao University, Xiamen 361021 (China); MOE Engineering Research Center for Brittle Materials Machining, Huaqiao University, Xiamen 361021 (China); Xu, Xipeng [Institute of Manufacturing Engineering, Huaqiao University, Xiamen 361021 (China); MOE Engineering Research Center for Brittle Materials Machining, Huaqiao University, Xiamen 361021 (China)

    2016-12-15

    Highlights: • Nano-silica abrasive with higher reactivity are prepared by hydrolysis-precipitation. • Polishing performance of soft-hard mixed abrasives during MCP is investigated. • Products of solid state reaction have been further confirmed by a new approach. • Material removal mechanism of sapphire with mixed abrasives is discussed. - Abstract: This study investigated the material removal mechanism of sapphire wafer with soft-hard mixed abrasives through mechanical chemical polishing (MCP). The polishing film, which contains diamond as hard abrasives and high reactivity silica as soft abrasives, is prepared through sol-gel technology. Silica abrasives with regular spherical shape and high reactivity are prepared through hydrolysis-precipitation. Diamond grits with three different particle sizes are used as abrasives. Results show that the rate of material removal of mixed abrasives during MCP is more than 52.6% of that of single hard abrasives and the decrease in surface roughness is more than 21.6% of that of single hard abrasives. These results demonstrate that the ideal planarization of sapphire wafer with high removal rate and good surface quality can be achieved when the effect of mechanical removal of hard abrasives and the chemical corrosion effect of soft abrasives are in dynamic equilibrium. A model that describes the material removal mechanism of sapphire with mixed abrasives during MCP is proposed. The results of thermodynamic calculation and polishing residue analysis are used to demonstrate the rationality of the model.

  5. Technology Demonstration of Wet Abrasive Blasting for Removal of Lead- and Asbestos-Containing Paint

    National Research Council Canada - National Science Library

    Race, Timothy

    2003-01-01

    ...). This technology demonstration showed that wet blasting using an engineered abrasive can safely and effectively remove lead- and asbestos-containing paint from exterior concrete masonry unit walls...

  6. Characterization of abrasion surfaces in rock shore environments of NW Spain

    Science.gov (United States)

    Feal-Pérez, Alejandra; Blanco-Chao, Ramón

    2013-04-01

    Despite the recent upsurge in rock coast research, many aspects of abrasion and their relationships to other processes remain poorly understood. In this paper, mechanisms subsumed under the general term abrasion were investigated at the beaches of Oia and Sartaña along the Galician coast of NW Spain, in particular at the micro- to meso-scale (mm-cm). Relationships between abrasion and mechanical rock strength served to explore feedbacks between weathering and abrasion on rock coasts, based on measurements of rock surface strength by means of the Equotip (Proceq) method, and stereomicroscope analyses of rock surfaces undergoing varying degrees of abrasion. The results suggest that (1) abrasion along near-vertical rock surfaces leads to a decrease in rock strength with elevation above the top of the basal sediment layer, (2) abrasion processes encompass two different modes, namely, the wave-induced sweeping and dragging of sand and gravel, and the projection of clasts against rock surfaces, each mode depending predominantly on the grain size of the abrasive agent, and (3) the two abrasion modes produce different rock surfaces whose roughness is strongly influenced by the properties of diverse minerals, in particular fracture and cleavage.

  7. Baking soda as an abrasive in toothpastes: Mechanism of action and safety and effectiveness considerations.

    Science.gov (United States)

    Hara, Anderson T; Turssi, Cecilia P

    2017-11-01

    Toothpastes can be formulated with different abrasive systems, depending on their intended clinical application. This formulation potentially affects their effectiveness and safety and, therefore, requires proper understanding. In this article, the authors focused on abrasive aspects of toothpastes containing sodium bicarbonate (baking soda), which have gained considerable attention because of their low abrasivity and good compatibility, while providing clinical effectiveness (further detailed in the other articles of this special issue). The authors first appraised the role of toothpaste abrasivity on tooth wear, exploring some underlying processes and the existing methods to determine toothpaste abrasivity. The authors reviewed the available data on the abrasivity of toothpastes containing baking soda and reported a summary of findings highlighting the clinical implications. On the basis of the collected evidence, baking soda has an intrinsic low-abrasive nature because of its comparatively lower hardness in relation to enamel and dentin. Baking soda toothpastes also may contain other ingredients, which can increase their stain removal effectiveness and, consequently, abrasivity. Even those formulations have abrasivity well within the safety limit regulatory agencies have established and, therefore, can be considered safe. Copyright © 2017 American Dental Association. Published by Elsevier Inc. All rights reserved.

  8. Surface roughness and wear of resin cements after toothbrush abrasion

    Directory of Open Access Journals (Sweden)

    Sérgio Kiyoshi ISHIKIRIAMA

    2015-01-01

    Full Text Available Increased surface roughness and wear of resin cements may cause failure of indirect restorations. The aim of this study was to evaluate quantitatively the surface roughness change and the vertical wear of four resin cements subjected to mechanical toothbrushing abrasion. Ten rectangular specimens (15 × 5 × 4 mm were fabricated according to manufacturer instructions for each group (n = 10: Nexus 3, Kerr (NX3; RelyX ARC, 3M ESPE (ARC; RelyX U100, 3M ESPE (U100; and Variolink II, Ivoclar/Vivadent (VL2. Initial roughness (Ra, µm was obtained through 5 readings with a roughness meter. Specimens were then subjected to toothbrushing abrasion (100,000 cycles, and further evaluation was conducted for final roughness. Vertical wear (µm was quantified by 3 readings of the real profile between control and brushed surfaces. Data were subjected to analysis of variance, followed by Tukey’s test (p < 0.05. The Pearson correlation test was performed between the surface roughness change and wear (p < 0.05. The mean values of initial/final roughness (Ra, µm/wear (µm were as follows: NX3 (0.078/0.127/23.175; ARC (0.086/0.246/20.263; U100 (0.296/0.589/16.952; and VL2 (0.313/0.512/22.876. Toothbrushing abrasion increased surface roughness and wear of all resin cements tested, although no correlation was found between those variables. Vertical wear was similar among groups; however, it was considered high and may lead to gap formation in indirect restorations.

  9. The change in retentive force of magnetic attachment by abrasion.

    Science.gov (United States)

    Huang, Yuanjin; Tawada, Yasuyuki; Hata, Yoshiaki; Watanabe, Fumihiko

    2008-07-01

    Magnets are frequently applied to removable dentures as retentive attachments. A magnet-retained removable overdenture might be slightly shifted from side to side by eccentric movement in the mouth, and the surface of magnetic attachment may be worn as a result. However, the relationship between the retentive force of magnetic attachment and its surface abrasion has not been reported. The purpose of this research is to investigate this relationship. Ten Mgfit DX 400 magnetic attachments for natural tooth roots were used for this experiment. The magnetic attachments were embedded in autopolymerizing acrylic resin, and ten pairs of specimens were fabricated. A 5-mm repeated gliding motion was applied on each pair of specimens until 30 000, 50 000, or 90 000 cycles had been achieved. The abrasion machine was under 5 kg loading, and the slide speed was 60 times/min. The retentive force of magnetic attachment was measured with a tension gauge at (1) before gliding; (2) after 30 000 gliding cycles; (3)after 50 000 gliding cycles; or (4) after 90 000 gliding cycles. The average change of retentive force of ten magnetic attachments after 30 000, 50 000, and 90 000 gliding cycles was 0.016 N, 0.003 N, and -0.008 N, respectively. The change was statistically analyzed using a paired-sample t test, which showed that the number of gliding cycles did not affect the retentive force of magnetic attachment significantly. The surface of magnetic attachment after gliding was observed by a microscope, and the abrasion of this attachment surface is clearly seen.

  10. Superficial characterization of titanium league when submitted to abrasive blasting; Caracterizacao superficial de titanio liga ao ser submetido a tratamento de jateamento

    Energy Technology Data Exchange (ETDEWEB)

    Suzuki, L.Y.; Leite, I.V.; Szesz, E.M.; Siqueira, C.J.M., E-mail: lsuzuki@neoortho.com.b [Universidade Federal do Parana (UFPR), Curitiba, PR (Brazil)

    2010-07-01

    Commercially pure titanium and some of its alloys exhibit a good biocompatibility. These characteristics are frequently used in the manufacture of orthopedic and dental implants. It is possible to modify its surface making it the bioactive using various methods, such as deposition of hydroxyapatite by plasma spray and increasing the roughness of the surface by abrasive blasting. This work is to modify the surface of titanium alloy Ti6Al4V ELI (ASTM F136: 02a) for abrasive blasting and study the morphology, crystallographic phases and the mechanical characteristics of the surface obtained. For such purpose, SEM images, diffraction of X-rays and tests of risk produced by nanoindenter. The sandblasting was done using alumina powder and blasting time of 6s. The morphology of the surfaces of Ti6Al4V ELI changed after sandblasting with increased roughness. It is possible to conclude that after sandblasting the titanium surface do not have a ductile behavior. (author)

  11. Effect of Heat Treatment on the Abrasive Wear Behavior of High Chromium Iron under Dry Sliding Condition

    Directory of Open Access Journals (Sweden)

    A.A. Ayeni

    2012-06-01

    Full Text Available The effect of heat treatment on the abrasive wear behavior of high chromium cast iron (NF253AHT under dry sliding condition has been investigated. Rectangular cross sectioned samples of the alloy were produced by sand casting. After casting, the samples were machined to equal dimensions of 50 mm x 15 mm x 10 mm and heat treated by annealing, hardening and tempering. Abrasive wear tests were carried out on the samples using the pin-on-disc wear test. The tests were carried out under restricted values of speed, load and time. Within this limit, the hardened sample displayed a superior wear resistance, while the annealed sample displayed the weakest wear resistance. A graphical model (wear map displaying all the wear regimes of the alloy, which may serve as a wear predictive tool was subsequently developed from the results of the wear tests. With the exception of the as-cast and annealed specimen, all other specimens (hardened and tempered have functioned adequately in wear prone environment, but with different degree of effectiveness. Hence, the hardened and tempered samples can be used in shot blast equipments and in the grinding of minerals.

  12. CHARACTERIZATION OF COMMERCIALLY AVAILABLE ALKALI RESISTANT GLASS FIBER FOR CONCRETE REINFORCEMENT AND CHEMICAL DURABILITY COMPARISON WITH SrO-Mn2O3-Fe2O3-MgO-ZrO2-SiO2 (SMFMZS SYSTEM GLASSES

    Directory of Open Access Journals (Sweden)

    Göktuğ GÜNKAYA

    2012-12-01

    Full Text Available According to the relevant literature, the utilization of different kind of glass fibers in concrete introduces positive effect on the mechanical behavior, especially toughness. There are many glassfibers available to reinforce concretes. Glass fiber composition is so important because it may change the properties such as strength, elastic modulus and alkali resistance. Its most important property to be used in concrete is the alkali resistance. Some glasses of SrO–MgO–ZrO2–SiO2 (SMZS quaternary system, such as 26SrO, 20MgO, 14ZrO2, 40SiO2 (Zrn glass, have been found to be highly alkali resistant thanks to their high ZrO2 and MgO contents. Previous researches on these glasses with MnO and/or Fe2O3 partially replacing SrO have been made with the aim of improving the chemical resistance and decreasing the production cost.The main target of the present study, first of all, was to characterize commercially available alkali resistant glass fiber for concrete reinforcement and then to compare its alkali durability with those of the SrO-Mn2O3-Fe2O3-MgO-ZrO2-SiO2 (SMFMZS system glasses. For such purposes, XRF, Tg-DTA, alkali resistance tests and SEM analysis conducted with EDX were employed. According tothe alkali endurance test results it was revealed that some of the SMFMZS system glass powders are 10 times resistant to alkali environments than the commercial glass fibers used in this study.Therefore, they can be considered as alternative filling materials on the evolution of chemically resistant concrete structures.

  13. Commercializing Patents

    National Research Council Canada - National Science Library

    Ted Sichelman

    2010-01-01

    .... Although more recent "prospect" theories properly recognize the importance of patent protection for commercializing inventions, they incorrectly conclude that strong, real property-like rights...

  14. Sliding-gate valve for use with abrasive materials

    Science.gov (United States)

    Ayers, Jr., William J.; Carter, Charles R.; Griffith, Richard A.; Loomis, Richard B.; Notestein, John E.

    1985-01-01

    The invention is a flow and pressure-sealing valve for use with abrasive solids. The valve embodies special features which provide for long, reliable operating lifetimes in solids-handling service. The valve includes upper and lower transversely slidable gates, contained in separate chambers. The upper gate provides a solids-flow control function, whereas the lower gate provides a pressure-sealing function. The lower gate is supported by means for (a) lifting that gate into sealing engagement with its seat when the gate is in its open and closed positions and (b) lowering the gate out of contact with its seat to permit abrasion-free transit of the gate between its open and closed positions. When closed, the upper gate isolates the lower gate from the solids. Because of this shielding action, the sealing surface of the lower gate is not exposed to solids during transit or when it is being lifted or lowered. The chamber containing the lower gate normally is pressurized slightly, and a sweep gas is directed inwardly across the lower-gate sealing surface during the vertical translation of the gate.

  15. Material removal mechanisms in abrasive vibration polishing of complex molds

    Science.gov (United States)

    Brinksmeier, E.; Riemer, O.; Schulte, H.

    2010-10-01

    Optical and medical industries are demanding a large variety of optical elements exhibiting complex geometries and multitude opto-functional areas in the range of a few millimeters [1]. Therefore, mold inserts made of steel or carbides must be finished by polishing for the replication of glass and plastic lenses [2]. For polishing theses complex components in the shape of localized cavities or grooves the application of rotating polishing pads is very limited. Established polishing processes are not applicable, so state of the art is a time consuming and therefore expensive polishing procedures by hand. An automated process with conventional polishing machines is impossible because of the complex mold insert geometry. The authors will present the development of a new abrasive polishing process for finishing these complex mold geometries to optical quality. The necessary relative velocity in the contact area between polishing pad and workpiece surface is exclusively realized by vibration motions which is an advantage over vibration assisted rotating polishing processes. The absence of rotation of the pad opens up the possibility to machine new types of surface geometries. The specific influence factors of vibration polishing were analyzed and will be presented. The determination of material removal behavior and polishing effect on planar steel samples has shown that the conventional abrasive polishing hypothesis of Preston is applicable to the novel vibration polishing process. No overlaid chemical material removal appears.

  16. Cutting Tools, Files and Abrasives. Pre-Apprenticeship Phase 1 Training.

    Science.gov (United States)

    Lane Community Coll., Eugene, OR.

    This self-paced student training module on cutting tools, files, and abrasives is one of a number of modules developed for Pre-apprenticeship Phase 1 Training. Purpose of the module is to enable students to identify and explain the proper use and care of various knives, saws, snips, chisels, and abrasives. The module may contain some or all of the…

  17. Process Monitoring Evaluation and Implementation for the Wood Abrasive Machining Process

    Directory of Open Access Journals (Sweden)

    Steven D. Jackson

    2010-11-01

    Full Text Available Wood processing industries have continuously developed and improved technologies and processes to transform wood to obtain better final product quality and thus increase profits. Abrasive machining is one of the most important of these processes and therefore merits special attention and study. The objective of this work was to evaluate and demonstrate a process monitoring system for use in the abrasive machining of wood and wood based products. The system developed increases the life of the belt by detecting (using process monitoring sensors and removing (by cleaning the abrasive loading during the machining process. This study focused on abrasive belt machining processes and included substantial background work, which provided a solid base for understanding the behavior of the abrasive, and the different ways that the abrasive machining process can be monitored. In addition, the background research showed that abrasive belts can effectively be cleaned by the appropriate cleaning technique. The process monitoring system developed included acoustic emission sensors which tended to be sensitive to belt wear, as well as platen vibration, but not loading, and optical sensors which were sensitive to abrasive loading.

  18. Process monitoring evaluation and implementation for the wood abrasive machining process.

    Science.gov (United States)

    Saloni, Daniel E; Lemaster, Richard L; Jackson, Steven D

    2010-01-01

    Wood processing industries have continuously developed and improved technologies and processes to transform wood to obtain better final product quality and thus increase profits. Abrasive machining is one of the most important of these processes and therefore merits special attention and study. The objective of this work was to evaluate and demonstrate a process monitoring system for use in the abrasive machining of wood and wood based products. The system developed increases the life of the belt by detecting (using process monitoring sensors) and removing (by cleaning) the abrasive loading during the machining process. This study focused on abrasive belt machining processes and included substantial background work, which provided a solid base for understanding the behavior of the abrasive, and the different ways that the abrasive machining process can be monitored. In addition, the background research showed that abrasive belts can effectively be cleaned by the appropriate cleaning technique. The process monitoring system developed included acoustic emission sensors which tended to be sensitive to belt wear, as well as platen vibration, but not loading, and optical sensors which were sensitive to abrasive loading.

  19. Air-propelled abrasive grit can damage the perennial weed, quackgrass, Elytrigia repens (L.) Nevski

    Science.gov (United States)

    New techniques are needed to control quackgrass in organic crops. With greater than or equal to 2 applications of abrasive air-propelled (800 kPa) corncob grit to 15 cm tall quackgrass tillers, regrowth was minimal at 5 weeks after treatment. Abrasive grits may be effective tools to help manage pere...

  20. Abrasive, silica phytoliths and the evolution of thick molar enamel in primates, with implications for the diet of Paranthropus boisei.

    Directory of Open Access Journals (Sweden)

    Diana Rabenold

    Full Text Available BACKGROUND: Primates--including fossil species of apes and hominins--show variation in their degree of molar enamel thickness, a trait long thought to reflect a diet of hard or tough foods. The early hominins demonstrated molar enamel thickness of moderate to extreme degrees, which suggested to most researchers that they ate hard foods obtained on or near the ground, such as nuts, seeds, tubers, and roots. We propose an alternative hypothesis--that the amount of phytoliths in foods correlates with the evolution of thick molar enamel in primates, although this effect is constrained by a species' degree of folivory. METHODOLOGY/PRINCIPAL FINDINGS: From a combination of dietary data and evidence for the levels of phytoliths in plant families in the literature, we calculated the percentage of plant foods rich in phytoliths in the diets of twelve extant primates with wide variation in their molar enamel thickness. Additional dietary data from the literature provided the percentage of each primate's diet made up of plants and of leaves. A statistical analysis of these variables showed that the amount of abrasive silica phytoliths in the diets of our sample primates correlated positively with the thickness of their molar enamel, constrained by the amount of leaves in their diet (R(2 = 0.875; p<.0006. CONCLUSIONS/SIGNIFICANCE: The need to resist abrasion from phytoliths appears to be a key selective force behind the evolution of thick molar enamel in primates. The extreme molar enamel thickness of the teeth of the East African hominin Paranthropus boisei, long thought to suggest a diet comprising predominantly hard objects, instead appears to indicate a diet with plants high in abrasive silica phytoliths.

  1. Effects of hard chrome and MoN-coated stainless steel on wear behaviour and tool life model under two-body abrasion wear testing

    Directory of Open Access Journals (Sweden)

    P. Srisattayakul

    2017-01-01

    Full Text Available The objectives of this study were to investigate the effect of the electroplated hard chrome (HC and the MoNcoated AISI 316 stainless steel coatings on weight loss under two-body abrasion wear testing and to predict the tool life of both materials used as a fishing net-weaving machine component, namely the hook. Both materials were used to carry out the wear experiments under two-body abrasion behavior. These specimens were wear tested with the in-house wear testing apparatus base on ASTM: G133-05 standard. The Taylor’s equation was used to formulate the tool life model whereas the Monte Carlo simulation was used to predict the tool life of the machine part. The results showed that the MoN-HC exhibited higher wear resistance than that of the HC.

  2. Complexity of the relationships between the sintering-temperature-dependent grain size, airborne-particle abrasion, ageing and strength of 3Y-TZP ceramics.

    Science.gov (United States)

    Cotič, Jasna; Jevnikar, Peter; Kocjan, Andraž; Kosmač, Tomaž

    2016-04-01

    This study was designed to explore the complex relationships between the sintering-temperature-dependent grain size, airborne-particle abrasion, ageing and strength of 3Y-TZP ceramics. Biomedical grade 3Y-TZP powder was used to fabricate 180 discs. Half of them were sintered at 1400°C for 2h and half at 1500°C for 2h. A total of 18 groups of 10 were formed and subjected to the fully crossed experimental protocol of airborne-particle abrasion with Al2O3 at 2.5bar (no abrasion, 50μm, 110μm) and accelerated ageing at 134°C (no ageing, 12h, 48h). The relative amount of monoclinic phase was determined with XRD. The biaxial flexural strength was measured and statistically analyzed using the three-way ANOVA followed by predetermined contrasts and Tukey's HSD test (α=0.05). The low-temperature-sintered, fine-grained ceramic exhibited an excellent ageing resistance, while the high-temperature-sintered, coarse-grained ceramic experienced a higher surface strengthening and a substantially improved ageing resistance with respect to the airborne-particle abrasion. The overall performance of this material was superior. Our results show that the sintering temperature has a minor effect on the flexural strength, but it plays a crucial role in the surface strengthening and the ageing behaviour of 3Y-TZP dental ceramics. Copyright © 2015 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  3. Influence of air-abrasion on zirconia ceramic bonding using an adhesive composite resin.

    Science.gov (United States)

    Yang, B; Barloi, A; Kern, M

    2010-01-01

    Air-abrasion as bonding conditioning method for zirconia ceramic might compromise the mechanical strength of zirconia restorations. The purpose of this study was to evaluate the influence of surface conditioning parameters, i.e., air-abrasion with reduced pressure or no air-abrasion and priming with adhesive primers on the long-term resin bond strength to zirconia ceramic. Zirconia ceramic disks were polished with 600 grit abrasive paper. Plexiglas tubes filled with composite resin were bonded with RelyX Unicem luting composite resin to the conditioned zirconia disks. Three surface conditions (unconditioned, air-born particle abrasion at 0.05 or 0.25 MPa) and four priming conditions (no priming, priming with Metal/Zirconia Primer, priming with Alloy Primer, priming with Clearfil Ceramic Primer) were tested. Sixteen specimens of each combination were bonded. Subgroups of eight bonded samples were stored in water either for 3 days or 150 days with 37,500 thermocycling. Tensile bond strengths (TBSs) were determined with a universal testing machine at a crosshead speed of 2mm/min. Without priming, RelyX Unicem showed durable bond strength to 0.25 MPa airborne-particle abraded ceramic. When combined with 10-methacryloyloxy-decyl dihydrogenphosphate containing primers, air-abrasion resulted in a durable TBS to zirconia ceramic even at a reduced abrasion pressure. However, combined with Metal/Zirconia Primer air-abrasion did not provide a durable TBS to zirconia ceramic. Using a self-adhesive luting resin composite (RelyX Unicem), air-abrasion at 0.25 MPa or the combination of low pressure air-abrasion and priming with MDP-containing primers seems to be useful to achieve durable long-term bonding to zirconia ceramic.

  4. A new method to test rock abrasiveness based on physico-mechanical and structural properties of rocks

    Directory of Open Access Journals (Sweden)

    V.N. Oparin

    2015-06-01

    Full Text Available A new method to test rock abrasiveness is proposed based upon the dependence of rock abrasiveness on their structural and physico-mechanical properties. The article describes the procedure of presentation of properties that govern rock abrasiveness on a canonical scale by dimensionless components, and the integrated estimation of the properties by a generalized index. The obtained results are compared with the known classifications of rock abrasiveness.

  5. Managing resistance to information system (IS) change at the pre-implementation stage from the senior management perspective : a case of a commercial bank in Vietnam

    OpenAIRE

    Le, Nguyen Hoang

    2016-01-01

    User resistance to information system (IS) change is an important issue in the IS literature. However, despite a large body of user adoption literature, there is far less literature addressing user resistance to IS change, especially in organisational contexts. Moreover, there are still left a number of open questions regarding the why and how resistance takes place. Particularly, previous research failed to explain these questions for two reasons. First, none of the previous research explain...

  6. Surface quality of marble machined by abrasive water jet

    Directory of Open Access Journals (Sweden)

    Ramy Abdullah

    2016-12-01

    Full Text Available This paper presents a study conducted to examine the effect of cutting parameters, namely standoff distance, nozzle traverse speed (TS, abrasive flow rate (AFR, and material type on cutting performance for two types of marble workpieces, Carrara white and Indian green. Statistical analysis was undertaken to assess the influence of the cutting parameters on the process performances in terms of surface roughness, surface waviness, and Kerf taper ratio. The results showed that the TS and material type were the most significant factors that affected surface roughness and Kerf taper ratio. Also, although AFR was found to have significant effect on surface waviness, it had no noticeable influence on surface roughness nor Kerf taper ratio.

  7. Monitoring and control of fine abrasive finishing processes

    DEFF Research Database (Denmark)

    Lazarev, Ruslan

    to remove unwanted material, obtain desired geometry, surface quality and surface functional properties. The automation and computerization of finishing processes involves utilisation of robots, specialized machines with several degrees of freedom, sensors and data acquisition systems. The focus...... of this work was to investigate foundations for process monitoring and control methods in application to semi-automated polishing machine based on the industrial robot. The monitoring system was built on NI data acquisition system with two sensors, acoustic emission sensor and accelerometer. Acquired sensory......In engineering, surfaces with specified functional properties are of high demand in various applications. Desired surface finish can be obtained using several methods. Abrasive finishing is one of the most important processes in the manufacturing of mould and dies tools. It is a principal method...

  8. Graphite Intended for Green Engineering Developed by Noncontaminant Reverse Abrasion

    Directory of Open Access Journals (Sweden)

    Roberto Baca Arroyo

    2016-01-01

    Full Text Available Graphite intended for green engineering was synthesized by noncontaminant reverse abrasion, which consists of graphite layers assembled with thickness controlled on SiC sandpaper as insulating substrate. Phase formation of the graphite layers was validated by X-ray diffraction studies and its finished profile by Atomic Force Microscopy (AFM. Transport parameters of only three layers were evaluated from current-voltage curves. Mathematical functions such as derivative and modulation of a signal have been built by graphite circuits using different performance principles, compared to those used with silicon devices. The trends related to electronic engineering should be achieved with design of the graphite-based devices to facilitate their mass production in the near future.

  9. STUDY OF POLISHING AISI 316L WITH STRUCTURED ABRASIVE

    Directory of Open Access Journals (Sweden)

    François GOOSSENS

    2015-05-01

    Full Text Available Finishing process like polishing is usually used to obtain high quality mechanical surface characteristics such as texture and roughness. These operations are mainly handmade and need highly trained operators thus limiting their repeatability and profitability. To optimize the industrialization of the polishing process, it is therefore necessary to modelize the process to built efficient parameter database. The aim of this study is to characterise the polishing of 316L stainless steel with structured abrasive belts. The geometric data of the belts are given, and we then propose a model to determine material removal. An experimental test bench is set up to test this model and characterise the polishing process in terms of forces. It produces samples for different polishing conditions. The different polished surfaces are then analyzed thanks to the roughness and the wettability. Using experimental designs, we are able to validate the proposed model and identify the parameters that influence a polishing operation.

  10. Abrasive slurry jet cutting model based on fuzzy relations

    Science.gov (United States)

    Qiang, C. H.; Guo, C. W.

    2017-12-01

    The cutting process of pre-mixed abrasive slurry or suspension jet (ASJ) is a complex process affected by many factors, and there is a highly nonlinear relationship between the cutting parameters and cutting quality. In this paper, guided by fuzzy theory, the fuzzy cutting model of ASJ was developed. In the modeling of surface roughness, the upper surface roughness prediction model and the lower surface roughness prediction model were established respectively. The adaptive fuzzy inference system combines the learning mechanism of neural networks and the linguistic reasoning ability of the fuzzy system, membership functions, and fuzzy rules are obtained by adaptive adjustment. Therefore, the modeling process is fast and effective. In this paper, the ANFIS module of MATLAB fuzzy logic toolbox was used to establish the fuzzy cutting model of ASJ, which is found to be quite instrumental to ASJ cutting applications.

  11. Fatigue Testing of Abrasive Water Jet Cut Titanium

    Energy Technology Data Exchange (ETDEWEB)

    Hovanski, Yuri; Dahl, Michael E.; Williford, Ralph E.

    2009-06-08

    Battelle Memorial Institute as part of its U.S. Department of Energy (USDOE) Contract No. DE-AC05-76RL01830 to operate the Pacific Northwest National Laboratory (PNNL) provides technology assistance to qualifying small businesses in association with a Technology Assistance Program (TAP). Qualifying companies are eligible to receive a set quantity of labor associated with specific technical assistance. Having applied for a TAP agreement to assist with fatigue characterization of Abrasive Water Jet (AWJ) cut titanium specimens, the OMAX Corporation was awarded TAP agreement 09-02. This program was specified to cover dynamic testing and analysis of fatigue specimens cut from titanium alloy Ti-6%Al-4%V via AWJ technologies. In association with the TAP agreement, a best effort agreement was made to characterize fatigue specimens based on test conditions supplied by OMAX.

  12. Mars rover rock abrasion tool performance enhanced by ultrasonic technology.

    Science.gov (United States)

    Macartney, A.; Li, X.; Harkness, P.

    2016-12-01

    The Mars exploration Athena science goal is to explore areas where water may have been present on the early surface of Mars, and investigate the palaeo-environmental conditions of these areas in relation to the existence of life. The Rock Abrasion Tool (RAT) designed by Honeybee Robotics has been one of four key Athena science payload instruments mounted on the mechanical arm of the Spirit, Opportunity and Curiosity Mars Exploration Rovers. Exposed rock surfaces weather and chemically alter over time. Although such weathered rock can present geological interest in itself, there is a limit to what can be learned. If the geological history of a landing site is to be constructed, then it is important to analyse the unweathered rock interior as clearly as possible. The rock abrasion tool's role is to substitute for a geologist's hammer, removing the weathered and chemically altered outer surface of rocks in order to view the pristine interior. The RAT uses a diamond resin standard common grinding technique, producing a 5mm depth grind with a relatively high surface roughness, achieved over a number of hours per grind and consumes approximately 11 watts of energy. This study assesses the benefits of using ultrasonic assisted grinding to improve surface smoothness. A prototype Micro-Optic UltraSonic Exfoliator (MOUSE) is tested on a range of rock types and demonstrates a number of advantages over the RAT. In addition to a smoother grind finish, these advantages include a lower rate of tool tip wear when using a tungsten carbide tip as opposed to diamond resin, less moving parts, a grind speed of minutes instead of hours, and a power consumption of only 1-5 Watts.

  13. Cover and Erosion Asymmetry in Saltation-Abrasion

    Science.gov (United States)

    Stark, C. P.; Parker, G.

    2014-12-01

    Erosion in bedrock-floored rivers is both driven and limited by the amount of sediment transported along the bed. Some sediment boosts wear rates, whereas too much generates a protective cover. This phenomenon determines the shape of river channels in a variety of landscapes and limits how fast they evolve. Here we reevaluate data from a well-known bedrock wear experiment to throw new light on how the saltation-abrasion process. Instead of a symmetric form for erosion versus sediment flux relative to transport capacity, we find the erosion rate peak shifts towards lower sediment fluxes when blocking of oblique saltation trajectories is taken into account. The theoretical context for this reevaluation is a cover-saltation-abrasion model, based on queueing theory (QT), for bedload transport over a planar bedrock bed. The QT approach provides some clarity in the stochastic treatment of granular impacts and cover, and generates closed-form solutions for wear rate in terms of sediment flux and simplified saltation geometry. Applied to the Sklar & Dietrich (2001) experiments in a very small recirculating flume, the two-parameter QT model fits the observed relation between erosion rate and sediment load, infers sediment flux as a function of load, admits non-negligible wear rates for a mean sediment depth of one grain, i.e., for full cover on average, but also suggests that bedrock erosion is blocked at >=50% instantaneous cover. The QT model makes testable predictions for future laboratory experiments and highlights the need for specific improvements in more comprehensive treatments of bedrock erosion and cover.

  14. Novel Attrition-Resistant Fischer Tropsch Catalyst

    Energy Technology Data Exchange (ETDEWEB)

    Weast, Logan, E.; Staats, William, R.

    2009-05-01

    There is a strong national interest in the Fischer-Tropsch synthesis process because it offers the possibility of making liquid hydrocarbon fuels from reformed natural gas or coal and biomass gasification products. This project explored a new approach that had been developed to produce active, attrition-resistant Fischer-Tropsch catalysts that are based on glass-ceramic materials and technology. This novel approach represented a promising solution to the problem of reducing or eliminating catalyst attrition and maximizing catalytic activity, thus reducing costs. The technical objective of the Phase I work was to demonstrate that glass-ceramic based catalytic materials for Fischer-Tropsch synthesis have resistance to catalytic deactivation and reduction of particle size superior to traditional supported Fischer-Tropsch catalyst materials. Additionally, these novel glass-ceramic-based materials were expected to exhibit catalytic activity similar to the traditional materials. If successfully developed, the attrition-resistant Fischer-Tropsch catalyst materials would be expected to result in significant technical, economic, and social benefits for both producers and public consumers of Fischer-Tropsch products such as liquid fuels from coal or biomass gasification. This program demonstrated the anticipated high attrition resistance of the glass-ceramic materials. However, the observed catalytic activity of the materials was not sufficient to justify further development at this time. Additional testing documented that a lack of pore volume in the glass-ceramic materials limited the amount of surface area available for catalysis and consequently limited catalytic activity. However, previous work on glass-ceramic catalysts to promote other reactions demonstrated that commercial levels of activity can be achieved, at least for those reactions. Therefore, we recommend that glass-ceramic materials be considered again as potential Fischer-Tropsch catalysts if it can be

  15. Characterization of the Micro-Abrasive Wear in Coatings of TaC-HfC/Au for Biomedical Implants

    Directory of Open Access Journals (Sweden)

    Pablo Guzmán

    2017-07-01

    Full Text Available The object of this work was the deposition of a Ta-Hf-C thin film with a gold interlayer on stainless steel, via the physical vapor deposition (PVD technique, in order to evaluate the properties of different systems subjected to micro-abrasive wear phenomena generated by alumina particles in Ringer's solution. The surface characterization was performed using a scanning electron microscope (SEM and atomic force microscope (AFM. The crystallographic phases exhibited for each coating were obtained by X-ray diffraction (XRD. As a consequence of modifying the composition of Ta-Hf there was evidence of an improvement in the micro-abrasive wear resistance and, for each system, the wear constants that confirm the enhancement of the surface were calculated. Likewise, these surfaces can be bioactive, generating an alternative to improve the biological fixation of the implants, therefore, the coatings of TaC-HfC/Au contribute in the development of the new generation of orthopedic implants.

  16. Relationships Between Abrasive Wear, Hardness, and Grinding Characteristics of Titanium-Based Metal-Matrix Composites

    Science.gov (United States)

    Blau, Peter J.; Jolly, Brian C.

    2009-06-01

    The objective of this work was to support the development of grinding models for titanium metal-matrix composites (MMCs) by investigating possible relationships between their indentation hardness, low-stress belt abrasion, high-stress belt abrasion, and the surface grinding characteristics. Three Ti-based particulate composites were tested and compared with the popular titanium alloy Ti-6Al-4V. The three composites were a Ti-6Al-4V-based MMC with 5% TiB2 particles, a Ti-6Al-4V MMC with 10% TiC particles, and a Ti-6Al-4V/Ti-7.5%W binary alloy matrix that contained 7.5% TiC particles. Two types of belt abrasion tests were used: (a) a modified ASTM G164 low-stress loop abrasion test, and (b) a higher-stress test developed to quantify the grindability of ceramics. Results were correlated with G-ratios (ratio of stock removed to abrasives consumed) obtained from an instrumented surface grinder. Brinell hardness correlated better with abrasion characteristics than microindentation or scratch hardness. Wear volumes from low-stress and high-stress abrasive belt tests were related by a second-degree polynomial. Grindability numbers correlated with hard particle content but were also matrix-dependent.

  17. Relationships Between Abrasive Wear, Hardness, and Surface Grinding Characteristics of Titanium-Based Metal Matrix Composites

    Energy Technology Data Exchange (ETDEWEB)

    Blau, Peter Julian [ORNL; Jolly, Brian C [ORNL

    2009-01-01

    The objective of this work was to support the development of grinding models for titanium metal-matrix composites (MMCs) by investigating possible relationships between their indentation hardness, low-stress belt abrasion, high-stress belt abrasion, and the surface grinding characteristics. Three Ti-based particulate composites were tested and compared with the popular titanium alloy Ti-6Al-4V. The three composites were a Ti-6Al-4V-based MMC with 5% TiB{sub 2} particles, a Ti-6Al-4V MMC with 10% TiC particles, and a Ti-6Al-4V/Ti-7.5%W binary alloy matrix that contained 7.5% TiC particles. Two types of belt abrasion tests were used: (a) a modified ASTM G164 low-stress loop abrasion test, and (b) a higher-stress test developed to quantify the grindability of ceramics. Results were correlated with G-ratios (ratio of stock removed to abrasives consumed) obtained from an instrumented surface grinder. Brinell hardness correlated better with abrasion characteristics than microindentation or scratch hardness. Wear volumes from low-stress and high-stress abrasive belt tests were related by a second-degree polynomial. Grindability numbers correlated with hard particle content but were also matrix-dependent.

  18. Investigation of Wear Resistant of Low-Alloyed and Chromium Cast Steel

    Directory of Open Access Journals (Sweden)

    A. Studnicki

    2012-04-01

    Full Text Available Results of investigations of wear resistant of two species of cast steel were introduced in the article (low-alloyed and chromium cast steel on the background of the standard material which was low alloy wear resistant steel about the trade name CREUSABRO ®8000. The investigations were executed with two methods: abrasive wears in the stream of loose particles (the stream of quartz sand and abrasive wears particles fixed (abrasive paper with the silicon carbide. Comparing the results of investigations in the experiments was based about the counted wear index which characterizes the wears of the studied material in the relation to the standard material.

  19. Abrasion behavior of graphite pebble in lifting pipe of pebble-bed HTR

    Energy Technology Data Exchange (ETDEWEB)

    Shen, Ke; Su, Jiageng [Institute of Nuclear and New Energy Technology, Advanced Nuclear Energy Technology Cooperation Innovation Center, The Key Laboratory of Advanced Nuclear Engineering and Safety, Ministry of Education, Beijing 10084 (China); Zhou, Hongbo [Institute of Nuclear and New Energy Technology, Advanced Nuclear Energy Technology Cooperation Innovation Center, The Key Laboratory of Advanced Nuclear Engineering and Safety, Ministry of Education, Beijing 10084 (China); Chinergy Co., LTD., Beijing 100193 (China); Peng, Wei; Liu, Bing [Institute of Nuclear and New Energy Technology, Advanced Nuclear Energy Technology Cooperation Innovation Center, The Key Laboratory of Advanced Nuclear Engineering and Safety, Ministry of Education, Beijing 10084 (China); Yu, Suyun, E-mail: suyuan@tsinghua.edu.cn [Center for Combustion Energy, The Key Laboratory for Thermal Science and Power Engineering, Ministry of Educations, Tsinghua University, Beijing 10084 (China)

    2015-11-15

    Highlights: • Quantitative determination of abrasion rate of graphite pebbles in different lifting velocities. • Abrasion behavior of graphite pebble in helium, air and nitrogen. • In helium, intensive collisions caused by oscillatory motion result in more graphite dust production. - Abstract: A pebble-bed high-temperature gas-cooled reactor (pebble-bed HTR) uses a helium coolant, graphite core structure, and spherical fuel elements. The pebble-bed design enables on-line refueling, avoiding refueling shutdowns. During circulation process, the pebbles are lifted pneumatically via a stainless steel lifting pipe and reinserted into the reactor. Inevitably, the movement of the fuel elements as they recirculate in the reactor produces graphite dust. Mechanical wear is the primary source of graphite dust production. Specifically, the sources are mechanisms of pebble–pebble contact, pebble–wall (structural graphite) contact, and fuel handling (pebble–metal abrasion). The key contribution to graphite dust production is from the fuel handling system, particularly from the lifting pipe. During pneumatic lift, graphite pebbles undergo multiple collisions with the stainless steel lifting pipe, thereby causing abrasion of the graphite pebbles and producing graphite dust. The present work explored the abrasion behavior of graphite pebble in the lifting pipe by measuring the abrasion rate at different lifting velocities. The abrasion rate of the graphite pebble in helium was found much higher than those in air and nitrogen. This gas environment effect could be explained by either tribology behavior or dynamic behavior. Friction testing excluded the possibility of tribology reason. The dynamic behavior of the graphite pebble was captured by analysis of the audio waveforms during pneumatic lift. The analysis results revealed unique dynamic behavior of the graphite pebble in helium. Oscillation and consequently intensive collisions occur during pneumatic lift, causing

  20. Prevalence of virulence and antimicrobial resistance genes in Salmonella spp. isolated from commercial chickens and human clinical isolates from South Africa and Brazil

    Directory of Open Access Journals (Sweden)

    Oliver T. Zishiri

    2016-03-01

    Full Text Available Salmonellosis is a significant public health concern around the world. The injudicious use of antimicrobial agents in poultry production for treatment, growth promotion and prophylaxis has resulted in the emergence of drug resistant strains of Salmonella. The current study was conducted to investigate the prevalence of virulence and antimicrobial resistance genes from Salmonella isolated from South African and Brazilian broiler chickens as well as human clinical isolates. Out of a total of 200 chicken samples that were collected from South Africa 102 (51% tested positive for Salmonella using the InvA gene. Of the overall 146 Salmonella positive samples that were screened for the iroB gene most of them were confirmed to be Salmonella enterica with the following prevalence rates: 85% of human clinical samples, 68.6% of South African chicken isolates and 70.8% of Brazilian chicken samples. All Salmonella isolates obtained were subjected to antimicrobial susceptibility testing with 10 antibiotics. Salmonella isolates from South African chickens exhibited resistance to almost all antimicrobial agents used, such as tetracycline (93%, trimethoprim-sulfamthoxazole (84%, trimethoprim (78.4%, kanamycin (74%, gentamicin (48%, ampicillin (47%, amoxicillin (31%, chloramphenicol (31%, erythromycin (18% and streptomycin (12%. All samples were further subjected to PCR in order to screen some common antimicrobial and virulence genes of interest namely spiC, pipD, misL, orfL, pse-1, tet A, tet B, ant (3"-la, sul 1 and sul. All Salmonella positive isolates exhibited resistance to at least one antimicrobial agent; however, antimicrobial resistance patterns demonstrated that multiple drug resistance was prevalent. The findings provide evidence that broiler chickens are colonised by pathogenic Salmonella harbouring antimicrobial resistance genes. Therefore, it is evident that there is a need for prudent use of antimicrobial agents in poultry production systems in

  1. Comparison of Three Commercial Molecular Assays for Detection of Rifampin and Isoniazid Resistance among Mycobacterium tuberculosis Isolates in a High-HIV-Prevalence Setting.

    Science.gov (United States)

    Strydom, K; Ismail, F; Matabane, M M Z; Onwuegbuna, O; Omar, S V; Ismail, N

    2015-09-01

    In a head-to-head comparison of the MTBDRplus version 2.0 (Hain Lifescience), the Xpert MTB/RIF (Cepheid), and the Anyplex MTB/NTM (Seegene) assays, we demonstrated equal sensitivity (59/61; 96.7%) and specificity (53/54; 98.1%) for detecting rifampin resistance with further analysis of discordances. The Xpert assay does not detect isoniazid resistance while the Anyplex assay showed high false positivity. Copyright © 2015, American Society for Microbiology. All Rights Reserved.

  2. Comparison of Three Commercial Molecular Assays for Detection of Rifampin and Isoniazid Resistance among Mycobacterium tuberculosis Isolates in a High-HIV-Prevalence Setting

    OpenAIRE

    Strydom, K.; Ismail, F.; Matabane, M.M.Z.; O. Onwuegbuna; S V Omar; N. Ismail

    2015-01-01

    In a head-to-head comparison of the MTBDRplus version 2.0 (Hain Lifescience), the Xpert MTB/RIF (Cepheid), and the Anyplex MTB/NTM (Seegene) assays, we demonstrated equal sensitivity (59/61; 96.7%) and specificity (53/54; 98.1%) for detecting rifampin resistance with further analysis of discordances. The Xpert assay does not detect isoniazid resistance while the Anyplex assay showed high false positivity.

  3. Surface assessment and modification of concrete using abrasive blasting

    Science.gov (United States)

    Millman, Lauren R.

    Composite systems are applied to concrete substrates to strengthen and extend the service life. Successful restoration or rehabilitation requires surface preparation prior to the application of the overlay. Surface coatings, waterproofing systems, and other external surface applications also require surface preparation prior to application. Abrasive blast media is often used to clean and uniformly roughen the substrate. The appropriate surface roughness is necessary to facilitate a strong bond between the existing substrate and overlay. Thus, surface modification using abrasive blast media (sand and dry ice), their respective environmental effects, surface roughness characterization prior to and after blasting, and the adhesion between the substrate and overlay are the focus of this dissertation. This dissertation is comprised of an introduction, a literature review, and four chapters, the first of which addresses the environmental effects due to abrasive blasting using sand, water, and dry ice. The assessment considered four response variables: carbon dioxide (CO2) emissions, fuel and energy consumption, and project duration. The results indicated that for sand blasting and water jetting, the primary factor contributing to environmental detriment was CO22 emissions from vehicular traffic near the construction site. The second chapter is an analysis of the International Concrete Repair Institute's (ICRI) concrete surface profiles (CSPs) using 3-D optical profilometry. The primary objective was to evaluate the suitability of approximating the 3-D surface (areal) parameters with those extracted from 2-D (linear) profiles. Four profile directions were considered: two diagonals, and lines parallel and transverse to the longitudinal direction of the mold. For any CSP mold, the estimation of the 3-D surface roughness using a 2-D linear profile resulted in underestimation and overestimation errors exceeding 50%, demonstrating the inadequacy of 2-D linear profiles to

  4. In Vitro Detection of Acaricidal Resistance Status of Rhipicephalus (Boophilus microplus against Commercial Preparation of Deltamethrin, Flumethrin, and Fipronil from North Gujarat, India

    Directory of Open Access Journals (Sweden)

    K. P. Shyma

    2015-01-01

    Full Text Available Rhipicephalus (Boophilus microplus is the most common tick species in India infesting cattle and buffaloes and causing significant economic losses to dairy and leather industries by adversely affecting the milk production and quality of hides. A study to evaluate the acaricide resistance status of Rhipicephalus (Boophilus microplus to deltamethrin, flumethrin, and fipronil was conducted on the samples collected from organized and unorganized farms of North Gujarat state, where treatment failures were reported frequently. Adult Immersion Test (AIT and Larval Packet Test (LPT were conducted using field strain for determination of 50 and 95% lethal concentration of deltamethrin, flumethrin, and fipronil. Results obtained by the Adult Immersion Test showed low grade resistance (level I, RF > 5 has been developed against both deltamethrin and fipronil. However, deltamethrin by performing Larval Packet Test showed moderate grade resistance (level II, RF > 25. Larval packet performed by flumethrin also revealed low grade resistance, level I. The data on field status of acaricide resistance from the area with diversified animal genetic resources will be helpful to adopt suitable strategy to overcome the process of development of resistance in ticks.

  5. Genome-wide association mapping of flowering time and northern corn leaf blight (Setosphaeria turcica) resistance in a vast commercial maize germplasm set.

    Science.gov (United States)

    Van Inghelandt, Delphine; Melchinger, Albrecht E; Martinant, Jean-Pierre; Stich, Benjamin

    2012-04-30

    Setosphaeria turcica is a fungal pathogen that causes northern corn leaf blight (NCLB) which is a serious foliar disease in maize. In order to unravel the genetic architecture of the resistance against this disease, a vast association mapping panel comprising 1487 European maize inbred lines was used to (i) identify chromosomal regions affecting flowering time (FT) and northern corn leaf blight (NCLB) resistance, (ii) examine the epistatic interactions of the identified chromosomal regions with the genetic background on an individual molecular marker basis, and (iii) dissect the correlation between NCLB resistance and FT. The single marker analyses performed for 8 244 single nucleotide polymorphism (SNP) markers revealed seven, four, and four SNP markers significantly (α=0.05, amplicon wise Bonferroni correction) associated with FT, NCLB, and NCLB resistance corrected for FT, respectively. These markers explained individually between 0.36 and 14.29% of the genetic variance of the corresponding trait. The very well interpretable pattern of SNP associations observed for FT suggested that data from applied plant breeding programs can be used to dissect polygenic traits. This in turn indicates that the associations identified for NCLB resistance might be successfully used in marker-assisted selection programs. Furthermore, the associated genes are also of interest for further research concerning the mechanism of resistance to NCLB and plant diseases in general, because some of the associated genes have not been mentioned in this context so far.

  6. In Vitro Detection of Acaricidal Resistance Status of Rhipicephalus (Boophilus) microplus against Commercial Preparation of Deltamethrin, Flumethrin, and Fipronil from North Gujarat, India

    Science.gov (United States)

    Shyma, K. P.; Gupta, Jay Prakash; Singh, Veer; Patel, K. K.

    2015-01-01

    Rhipicephalus (Boophilus) microplus is the most common tick species in India infesting cattle and buffaloes and causing significant economic losses to dairy and leather industries by adversely affecting the milk production and quality of hides. A study to evaluate the acaricide resistance status of Rhipicephalus (Boophilus) microplus to deltamethrin, flumethrin, and fipronil was conducted on the samples collected from organized and unorganized farms of North Gujarat state, where treatment failures were reported frequently. Adult Immersion Test (AIT) and Larval Packet Test (LPT) were conducted using field strain for determination of 50 and 95% lethal concentration of deltamethrin, flumethrin, and fipronil. Results obtained by the Adult Immersion Test showed low grade resistance (level I, RF > 5) has been developed against both deltamethrin and fipronil. However, deltamethrin by performing Larval Packet Test showed moderate grade resistance (level II, RF > 25). Larval packet performed by flumethrin also revealed low grade resistance, level I. The data on field status of acaricide resistance from the area with diversified animal genetic resources will be helpful to adopt suitable strategy to overcome the process of development of resistance in ticks. PMID:26788362

  7. In Vitro Detection of Acaricidal Resistance Status of Rhipicephalus (Boophilus) microplus against Commercial Preparation of Deltamethrin, Flumethrin, and Fipronil from North Gujarat, India.

    Science.gov (United States)

    Shyma, K P; Gupta, Jay Prakash; Singh, Veer; Patel, K K

    2015-01-01

    Rhipicephalus (Boophilus) microplus is the most common tick species in India infesting cattle and buffaloes and causing significant economic losses to dairy and leather industries by adversely affecting the milk production and quality of hides. A study to evaluate the acaricide resistance status of Rhipicephalus (Boophilus) microplus to deltamethrin, flumethrin, and fipronil was conducted on the samples collected from organized and unorganized farms of North Gujarat state, where treatment failures were reported frequently. Adult Immersion Test (AIT) and Larval Packet Test (LPT) were conducted using field strain for determination of 50 and 95% lethal concentration of deltamethrin, flumethrin, and fipronil. Results obtained by the Adult Immersion Test showed low grade resistance (level I, RF > 5) has been developed against both deltamethrin and fipronil. However, deltamethrin by performing Larval Packet Test showed moderate grade resistance (level II, RF > 25). Larval packet performed by flumethrin also revealed low grade resistance, level I. The data on field status of acaricide resistance from the area with diversified animal genetic resources will be helpful to adopt suitable strategy to overcome the process of development of resistance in ticks.

  8. The present status of commercialized and developed biotech (GM) crops, results of evaluation of plum 'HoneySweet" for resistance to plum pox virus in the Czech Republic

    Science.gov (United States)

    Commercialization of biotech (GM) crops started in 1996. A significant increase of 9 million hectars was realized in 1996-2009. In the years 2010-2011, it was already 12 million hectars (8 percent of total crop area). 16.7 million farmers in 29 countries planted 160 million hectars of GM crops in...

  9. MER 1 MARS ROCK ABRASION TOOL EDR OPS VERSION 1.0

    Data.gov (United States)

    National Aeronautics and Space Administration — This archive contains Mars Exploration Rover Operations (Ops) Rock Abrasion Tool (RAT) Experiment Data Record (EDR) products and ancillary files. The RAT Operations...

  10. Treatment of gingival hyperpigmentation with rotary abrasive, scalpel, and laser techniques: A case series

    Science.gov (United States)

    Murthy, M Bhanu; Kaur, Jasjit; Das, Rupali

    2012-01-01

    Melanin pigmentation often occurs in the gingiva as a result of an abnormal deposition of melanin, due to which the gums may appear black, but the principles, techniques, and management of the problems associated with gingival melanin pigmentation are still not fully established. Depigmentation procedures such as scalpel surgery, gingivectomy with free gingival autografting, electrosurgery, cryosurgery, chemical agents such as 90% phenol and 95% alcohol, abrasion with diamond bur, Nd: YAG laser, semiconductor diode laser, and CO2 laser have been employed for removal of melanin hyper pigmentation. The following case series describes three different surgical depigmentation techniques: scalpel surgery, abrasion with rotary abrasive, and a diode laser. Better results of depigmentation were achieved with diode laser than conventional scalpel and with rotary abrasion with respect to esthetics. The results point out that lasers are an effective and a safe means to removal of hyperpigmentation from the gingiva. Healing was uneventful and no repigmentation occurred. PMID:23493062

  11. Dental Abrasion of Incisor caused by a Babies' Dummy Clip: A Case Report.

    Science.gov (United States)

    Doğramacı, Esma J; Rossi-Fedele, Giampiero

    2015-09-01

    Tooth surface loss (TSL), the non-carious loss of tooth tissue, is considered pathological if the teeth involved experience sensitivity and pain, are functionally compromised or they detract from the patient's appearance. TSL is a common clinical finding in many patient groups, although differences between the primary and permanent dentition contribute to TSL occurring at a faster rate and with worse outcomes in the primary dentition. This case report presents localized abrasion and associated apical periodontitis affecting a single primary tooth in a 2-year-old infant following the misuse of a babies' dummy clip whilst teething. Abrasion is rare in the primary dentition. CPD/CLINICAL RELEVANCE: This article highlights an unusual presentation of dental abrasion affecting the primary dentition caused by a previously unreported foreign object; abrasion in this case was a side-effect of soothing the discomfort of teething.

  12. Surface roughness and gloss of current CAD/CAM resin composites before and after toothbrush abrasion.

    Science.gov (United States)

    Koizumi, Hiroyasu; Saiki, Osamu; Nogawa, Hiroshi; Hiraba, Haruto; Okazaki, Tomoyo; Matsumura, Hideo

    2015-01-01

    The purpose of this study was to evaluate the gloss and surface roughness behaviors of newly developed CAD/CAM composite blocks with different filler contents and characteristics. The gloss and surface roughness were quantified before and after a toothbrush dentifrice abrasion test; the results were compared to the gloss and surface roughness of a ceramic CAD/CAM block. Knoop hardness was determined before abrasion test. The results were analyzed by ANOVA, Tukey HSD, and Dunnett t test (pVita Enamic>Gradia block>Shofu Block HC, Lava Ultimate≥Katana Avencia block≥Cerasmart. After toothbrush abrasion, a significant difference in the gloss unit was detected between the Shofu Block HC material and the ceramic block. The Ra and Rz of the Cerasmart and Shofu Block HC materials were significantly larger than those of the ceramic block after toothbrush abrasion.

  13. Drawing Light-fields: Hand-drawn Approaches to Abrasion Holography

    Science.gov (United States)

    Duke, T.

    2013-02-01

    Abrasion holography has received little attention since the technique was described by William J. Beaty in the early 1990's. In this paper the limitations of abrasion holography are explored, and new approaches are presented which expand the possibilities of the medium. New tools presented here offer new possibilities to the artist wishing to draw holograms by hand. Methods are described by which complex curves and organic forms can be constructed by hand more easily and intuitively than previously described. In an analysis of reconstruction lighting and viewing geometries, new solutions to reduce or eliminate distortions are suggested. Various tools, materials, and scratch geometries are considered for optimum 3D illusion. A new class of abrasion holograms is presented that use elliptical, hypotrochoidal, and epitrochoidal scratch geometries, exhibiting novel animation effects. In conclusion, a method for embossing abrasion holograms with the aid of an etching press is described.

  14. Treatment of gingival hyperpigmentation with rotary abrasive, scalpel, and laser techniques: A case series.

    Science.gov (United States)

    Murthy, M Bhanu; Kaur, Jasjit; Das, Rupali

    2012-10-01

    Melanin pigmentation often occurs in the gingiva as a result of an abnormal deposition of melanin, due to which the gums may appear black, but the principles, techniques, and management of the problems associated with gingival melanin pigmentation are still not fully established. Depigmentation procedures such as scalpel surgery, gingivectomy with free gingival autografting, electrosurgery, cryosurgery, chemical agents such as 90% phenol and 95% alcohol, abrasion with diamond bur, Nd: YAG laser, semiconductor diode laser, and CO2 laser have been employed for removal of melanin hyper pigmentation. The following case series describes three different surgical depigmentation techniques: scalpel surgery, abrasion with rotary abrasive, and a diode laser. Better results of depigmentation were achieved with diode laser than conventional scalpel and with rotary abrasion with respect to esthetics. The results point out that lasers are an effective and a safe means to removal of hyperpigmentation from the gingiva. Healing was uneventful and no repigmentation occurred.

  15. Study of kerf geometry of multilayers materials in abrasive water jet cutting process

    Directory of Open Access Journals (Sweden)

    Barabas Bogdan

    2017-01-01

    Full Text Available The use of abrasive jet cutting in case of multilayers materials, shows particularities and difficulties, due to different hardness and thickness of layers. This paper studies changes, occurred in the kerf geometry at passing of abrasive particles, through layers with different hardness and aims to establish a link between hardness and thickness of the layers and kerf geometry because processing accuracy is determined by the geometry of the cut. Thus, is proposed a novel algorithm based on minimization of angle of kerf, for optimization a cutting process in abrasive water jet technology, which can be utilized for materials with different hardness in layers. Direct effect of optimization of cutting consist in increasing efficiency, dimensional precision, traverse velocity, and decreasing the amount of used abrasive garnet.

  16. Self-Organization of Friction Surface of Fe-Mn-C-B Coating With Increased Resistance to Abrasion / Samoorganizacja Powierzchni Tarcia Powłoki Fe-Mn-C-B O Zwiększonej Odporności Na Zużycie Ścierne

    Directory of Open Access Journals (Sweden)

    Barszcz M.

    2015-12-01

    Full Text Available The paper concerns the research on self-organization of the surface of coating of hypoeutectic alloy Fe-Mn-C-B modified Si, Ni, Cr, Cu with friction with C45 steel. The coatings were obtained by arc welding using a flux-cored wire. Tests of resistance to wear were carried out for hypoeutectic coatings with use of the friction pair pin-on-disc in the conditions of sliding friction, in model lubricating environments. The surface-active (glycerol oil and inactive (Vaseline grease lubricant was used. Tribological tests carried out showed that cooperation of hypoeutectic alloy coating with counterbody of C45 steel with lubrication with surface-active lubricant results in a significant improvement in tribological properties than in case of the lubrication with surface-inactive lubricant. The resulting effect is related to the self-organization of friction surface. After deposition and wear resistance tests, the friction surface microstructure was analysed, as well as the surface and depth distribution of the elements.

  17. Alliance of oral hygiene practices and abrasion among urban and rural residents of Central India.

    Science.gov (United States)

    Yadav, Naveen S; Saxena, Vrinda; Reddy, Raghavendra; Deshpande, Neeraj; Deshpande, Anshula; Kovvuru, Suresh Kumar

    2012-01-01

    To attain alliance between the oral hygiene practices with prevalence of tooth abrasion among urban and rural adult population of Central India. To plan dental care services in inaccessible areas and to suggest appropriate remedial measures to prevent this avertable and self-inflicted injury of teeth in this cross-sectional study. A sum of 1045 adult residents both from Urban (529) and rural (516) parts of Bhopal district (Central India) was selected on a random basis. The multistage sampling technique was adopted to ascertain the sample size. In urban area the study population consisted of 240 males, 289 females and 201 males and 315 females in rural area respectively. All residents above 18 years of age from the Bhopal district were included in cross-sectional study. Assessment form comprises of questionnaire and general information on oral hygiene practices, dietary habits and medical history. Abrasion was assessed using diagnostic criteria recommended by Smith and Knight (modified). Chi- square test was used to test associations between categorical variables at 5% level of significance. Regression analysis attempted to define for risk factors causing abrasion. Literature on the prevalence of abrasion is very sparse, so attempt is made to correlate the etiological factors and recommend to prevent tooth wear. Investigation of this cross-sectional study was aggregate of 1045 residences. Result shows high prevalence of abrasion 70.2%. Higher prevalence concomitant with diffident habits related to oral hygiene maintenance was recorded more among rural (76.9%) when compared to urban dwellers (63.7%). Presence of abrasion verifies statistical significance in relation to age, rural urban difference and variations in habit of oral hygiene care. Stated in the present study, avertable and self-inflicted is tooth abrasion, recurrently resulted by the reprehensible brushing method and common use of indigenous material for the maintenance of oral hygiene. Shows significant

  18. Laboratory Measurements of Particulate Matter Concentrations from Asphalt Pavement Abrasion

    Directory of Open Access Journals (Sweden)

    Fullová Daša

    2016-12-01

    Full Text Available The issue of emissions from road traffic is compounded by the fact that the number of vehicles and driven kilometres increase each year. Road traffic is one of the main sources of particulate matter and traffic volume is still increasing and has unpleasant impact on longevity of the pavements and the environment. Vehicle motions cause mechanical wearing of the asphalt pavement surface - wearing course by vehicle tyres. The contribution deals with abrasion of bituminous wearing courses of pavements. The asphalt mixtures of wearing courses are compared in terms of mechanically separated particulate matter. The samples of asphalt mixtures were rutted in wheel tracking machine. The particulate matter measurements were performed in laboratory conditions. The experimental laboratory measurements make it possible to sample particulates without contamination from exhaust emissions, abraded particles from vehicles, resuspension of road dust and climate affects. The contribution offers partial results of measurements on six trial samples of asphalt mixtures with different composition. It presents particulate matter morphology and the comparison of rutted asphalt samples in terms of PM mass concentrations and chemical composition.

  19. Particulate matter mass concentrations produced from pavement surface abrasion

    Directory of Open Access Journals (Sweden)

    Fullova Dasa

    2017-01-01

    Full Text Available According to the latest findings particulate matter belong to the most significant pollutants in Europe together with ground-level ozone O3 and nitrogen dioxide NO2. Road traffic is one of the main sources of particulate matter. Traffic volume has unpleasant impact on longevity of the pavements and also on the environment. Vehicle motions cause mechanical wearing of the asphalt pavement surface - wearing course by vehicle tyres. The paper deals with abrasion of bituminous wearing courses of pavements. The asphalt mixtures are compared in terms of mechanically separated particulate matter. The samples of asphalt mixtures were rutted in wheel tracking machine. The particulate matter measurements were performed in laboratory conditions. The experimental laboratory measurements make it possible to sample particulates without contamination from exhaust emissions, abraded particles from vehicles, resuspension of road dust and climate affects. The paper offers partial results of measurements on six trial samples of asphalt mixtures with different composition. It presents particulate matter morphology and the comparison of rutted asphalt samples in terms of PM mass concentrations and chemical composition.

  20. Multi-objective Optimization of Process Performances when Cutting Carbon Steel with Abrasive Water Jet

    Directory of Open Access Journals (Sweden)

    M. Radovanović

    2016-12-01

    Full Text Available Multi-objective optimization of process performances (perpendicularity deviation, surface roughness and productivity when cutting carbon steel EN S235 with abrasive water jet is presented in this paper. Cutting factors (abrasive flow rate, traverse rate and standoff distance were determined when perpendicularity deviation and surface roughness are minimal and productivity is maximal. Multi-objective genetic algorithm (MOGA was used for the determination set of nondominated optimal points, known as Pareto front.

  1. The influence of mixing water and abrasives on the quality of machined surface

    Directory of Open Access Journals (Sweden)

    A. Stoić

    2014-04-01

    Full Text Available This paper shows the impact of mixing water and abrasives in water jet cutting process on the quality of the machined surface. The tests were done with polymer material SIPAS, where the influence of cutting parameters was researched (cutting pressure, cutting feed and abrasive mass flow. The surface roughness was measured on several zones, regarding the depth of materials, because the roughness is increased with the material thickness.

  2. Examination of Wetting by Liquid Zinc of Steel Sheets Following Various Kinds of Abrasive Blasting

    Directory of Open Access Journals (Sweden)

    Cecotka M.

    2016-06-01

    Full Text Available Abrasive blasting is one of the methods of surface working before hot-dip zinc-coating. It allows not only to remove products of corrosion from the surface, but it also affects the quality of the zinc coating applied later, thereby affecting wettability of surface being zinc-coated. The surface working can be done with different types of abrasive material.

  3. Abrasive blasting contamination in Super Duplex and carbon steels - a quantification approach by rietveld analysis

    OpenAIRE

    Rocha,Adriana da Cunha; Nascimento, Áquila Vieira do; Margarit-Mattos, Isabel Cristina Pereira; Assis, Kioshy dos Santos; Mattos, Oscar Rosa

    2014-01-01

    A methodology for quantifying the contamination after abrasive blasting by Aluminum Oxide and Martensitic Carbon Steel particles in Super Duplex and Carbon Steel substrates has been developed. The method consisted of performing x-ray diffraction in the blasted steel substrates and calculating the particle contamination using Rietveld Quantitative Method. In this way, it is possible to evaluate the substrate volume in which the abrasive particles have been trapped (taking into account the surf...

  4. Marginal leakage in permanent teeth after dentin treatment with air abrasion and adhesive systems

    OpenAIRE

    Zuanon, Angela C. C.; Capote,Ticiana S. O.

    2010-01-01

    Due to doubts related to the application and association of techniques for appropriate adhesion, as the air abrasion system and last generation adhesive systems, the objective of this study was to evaluate the marginal leakage in Class V composite restorations in permanent teeth prepared with rotating instruments and then submitted to air abrasion and adhesive systems. Cavities were prepared with burs in high speed in facial and lingual surfaces of 25 human third molars. The specimens were di...

  5. Characterization of Conventional and High-Translucency Y-TZP Dental Ceramics Submitted to Air Abrasion.

    Science.gov (United States)

    Tostes, Bhenya Ottoni; Guimarães, Renato Bastos; Noronha-Filho, Jaime Dutra; Botelho, Glauco Dos Santos; Guimarães, José Guilherme Antunes; Silva, Eduardo Moreira da

    2017-01-01

    This study evaluated the effect of air-abrasion on t®m phase transformation, roughness, topography and the elemental composition of three Y-TZP (Yttria-stabilized tetragonal zirconia polycrystal) dental ceramics: two conventional (Lava Frame and IPS ZirCad) and one with high-translucency (Lava Plus). Plates obtained from sintered blocks of each ceramic were divided into four groups: AS (as-sintered); 30 (air-abrasion with 30 mm Si-coated Al2O3 particles); 50 (air-abrasion with 50 mm Al2O3 particles) and 150 (air-abrasion with 150 mm Al2O3 particles). After the treatments, the plates were submitted to X-ray diffractometry; 3-D profilometry and SEM/EDS. The AS surfaces were composed of Zr and t phases. All treatments produced t®m phase transformation in the ceramics. The diameter of air-abrasion particles influenced the roughness (150>50>30>AS) and the topography. SEM analysis showed that the three treatments produced groove-shaped microretentions on the ceramic surfaces, which increased with the diameter of air-abrasion particles. EDS showed a decrease in Zr content along with the emergence of O and Al elements after air-abrasion. Presence of Si was also detected on the plates air-abraded with 30 mm Si-coated Al2O3 particles. It was concluded that irrespective of the type and diameter of the particles, air-abrasion produced t®m phase transformation, increased the roughness and changed the elemental composition of the three Y-TZP dental ceramics. Lava Plus also behaved similarly to the conventional Y-TZP ceramics, indicating that this high translucency ceramic could be more suitable to build monolithic ceramic restorations in the aesthetic restorative dentistry field.

  6. RESIZING OF THE CRANIOMANDIBULAR RELATION IN THE REHABILITATION OF DENTAL ABRASION

    OpenAIRE

    Delia BAHRIM; Aurel APINTILIESEI; Alexandru Vasile BURLUI; Oana CUCOVEICĂ; Gîrbea, Cătălina; Carmen STADOLEANU

    2016-01-01

    Dental abrasion appears as a complex phenomenon among the multitude of clinical manifestations occurring in patients who require a complex oral rehabilitation. The therapeutical solutions for such cases are quite elaborate, involving interdisciplinary contributions from the part of various specialists.Obviously, elucidation of the complex cases of dental abrasion is possible when their standardized classification and, equally, a well-established therapeutical conduct, considering the class of...

  7. Surface properties and fatigue failure analysis of alloy 718 surfaces milled by abrasive and plain waterjet

    OpenAIRE

    Rivero, A.; Alberdi, A.; T. de Artaza; Mendia, L.; Lamikiz, A.

    2017-01-01

    This work analyzes the surfaces obtained in alloy 718 when they are milled by abrasive waterjet (AWJ) at different conditions, and the effect of main process parameters on the characteristics of these surfaces. This analysis revealed that all surfaces have a homogeneous roughness in the transversal and the longitudinal directions, present embedded abrasive particles and have hardened about 50% with respect to the untreated bulk alloy 718. In addition, plain waterjet (PWJ) technology was used ...

  8. Treatment of traumatic corneal abrasions: a three-arm, prospective, randomized study.

    Science.gov (United States)

    Menghini, M; Knecht, P B; Kaufmann, C; Kovacs, R; Watson, S L; Landau, K; Bosch, M M

    2013-01-01

    To compare three different treatment modalities for traumatic corneal abrasions. We conducted a prospective, randomized, masked, three-arm clinical study of patients presenting with superficial corneal foreign bodies. Treatment modalities were: (1) pressure patching with ofloxacin ointment (patch group, PG, n = 18), (2) therapeutic contact lens with ofloxacin eye drops (contact lens group, CLG, n = 20) and (3) ofloxacin ointment alone (ointment group, OG, n = 28). Primary outcome measure was the difference of the mean corneal abrasion area between the three groups at 3 different time points (baseline, day 1 and day 7). A total of 66 patients were included in the study over a period of 2 years. Mean initial corneal abrasion area was 3.6 ± 3.4 mm² in the PG, 4.2 ± 4.0 mm² in the CLG and 3.7 ± 3.1 mm² in the OG (p = 0.875). Differences in corneal abrasion area at any time point were not statistically significant (abrasion area decrease from presentation to day 1 was 3.4 ± 3.3 mm² in the PG, 4.1 ± 4.0 mm² in the CLG and 3.5 ± 3.1 mm² in the OG, p = 0.789). The epithelium was healed in all patients at day 7. Treating traumatic corneal abrasions by pressure patching, a bandage contact lens or ointment alone was equal in reducing the abrasion area or reducing pain. According to our results the treatment of choice for traumatic abrasions may be adapted to the needs and preferences of the patient. Copyright © 2013 S. Karger AG, Basel.

  9. Development of Abrasive Selection Model/Chart for Palm Frond Broom Peeling Machine Design

    OpenAIRE

    Nwankwojike; B. Nduka

    2014-01-01

    A model for predicting the friction required by a palm frond broom peeling machine for effective peeling of palm leaf to broom bristle and a chart for selecting the best abrasive material for this machine’s peeling operation were developed in this study using mechanistic modeling method. The model quantified the relationship between the coefficient of friction and other operational parameters of this machine while the abrasives selection chart constitutes a plot of this measured f...

  10. Characterization of the commercially-available fluorescent chloroquine-BODIPY conjugate, LynxTag-CQGREEN, as a marker for chloroquine resistance and uptake in a 96-well plate assay.

    Directory of Open Access Journals (Sweden)

    Cheryl C Y Loh

    Full Text Available Chloroquine was a cheap, extremely effective drug against Plasmodium falciparum until resistance arose. One approach to reversing resistance is the inhibition of chloroquine efflux from its site of action, the parasite digestive vacuole. Chloroquine accumulation studies have traditionally relied on radiolabelled chloroquine, which poses several challenges. There is a need for development of a safe and biologically relevant substitute. We report here a commercially-available green fluorescent chloroquine-BODIPY conjugate, LynxTag-CQGREEN, as a proxy for chloroquine accumulation. This compound localized to the digestive vacuole of the parasite as observed under confocal microscopy, and inhibited growth of chloroquine-sensitive strain 3D7 more extensively than in the resistant strains 7G8 and K1. Microplate reader measurements indicated suppression of LynxTag-CQGREEN efflux after pretreatment of parasites with known reversal agents. Microsomes carrying either sensitive- or resistant-type PfCRT were assayed for uptake; resistant-type PfCRT exhibited increased accumulation of LynxTag-CQGREEN, which was suppressed by pretreatment with known chemosensitizers. Eight laboratory strains and twelve clinical isolates were sequenced for PfCRT and Pgh1 haplotypes previously reported to contribute to drug resistance, and pfmdr1 copy number and chloroquine IC50s were determined. These data were compared with LynxTag-CQGREEN uptake/fluorescence by multiple linear regression to identify genetic correlates of uptake. Uptake of the compound correlated with the logIC50 of chloroquine and, more weakly, a mutation in Pgh1, F1226Y.

  11. Protein supplementation and dietary behaviours of resistance trained men and women attending commercial gyms: a comparative study between the city centre and the suburbs of Palermo, Italy.

    Science.gov (United States)

    Bianco, Antonino; Mammina, Caterina; Thomas, Ewan; Bellafiore, Marianna; Battaglia, Giuseppe; Moro, Tatiana; Paoli, Antonio; Palma, Antonio

    2014-01-01

    It is anecdotally recognized that commercial gym users assume supplements in order to improve performance or health. However, dietary behaviours of people and athletes attending commercial gyms have been poorly studied. The exact amount and frequency of dietary supplements consumption are still needed to be investigated. The main purpose of this study is to understand the quantity and quality of food intake, as well as dietary supplementation in people attending commercial gyms. Secondly to compare the city centre and the suburbs of Palermo, Italy. A face-to-face questionnaire was administered to 561 subjects, 207 from the city centre (CC) and 354 from the suburbs (SB) of Palermo, Italy. Frequency of protein supplements use and association with dietary behaviours were investigated. Subsequently, the frequency distribution was used for demographic assessment. Frequency of protein consumption was similar in both groups (30% for CC and 28.8% for SB). Males show greater consumption percentages than females (30.5% in males and 6.9% in females). Milk and chicken are the most frequently consumed foods. Data show that non-supplement users (NSU) consume significantly more snacks and bakery products than supplement users (SU) (P commercial gym users is 30% for the CC and 28.8% for the SB. Significant differences were found between CC and SB females, underlining an interesting discrepancy, indicating to dietary supplement industries regarding regional implications. Subjects that use protein supplements also consume larger quantities of high protein food compared to NSU. NSU also eat higher proportions of unhealthy food compared to SU.

  12. Effect of NaF, SnF2, and TiF4 Toothpastes on Bovine Enamel and Dentin Erosion-Abrasion In Vitro

    Science.gov (United States)

    Comar, Lívia Picchi; Gomes, Marina Franciscon; Ito, Naiana; Salomão, Priscila Aranda; Grizzo, Larissa Tercília; Magalhães, Ana Carolina

    2012-01-01

    The aim of this study was to compare the effect of toothpastes containing TiF4, NaF, and SnF2 on tooth erosion-abrasion. Bovine enamel and dentin specimens were distributed into 10 groups (n = 12): experimental placebo toothpaste (no F); NaF (1450 ppm F); TiF4 (1450 ppm F); SnF2 (1450 ppm F); SnF2 (1100 ppm F) + NaF (350 ppm F); TiF4 (1100 ppm F) + NaF (350 ppm F); commercial toothpaste Pro-Health (SnF2—1100 ppm F + NaF—350 ppm F, Oral B); commercial toothpaste Crest (NaF—1.500 ppm F, Procter & Gamble); abrasion without toothpaste and only erosion. The erosion was performed 4 × 90 s/day (Sprite Zero). The toothpastes' slurries were applied and the specimens abraded using an electric toothbrush 2 × 15 s/day. Between the erosive and abrasive challenges, the specimens remained in artificial saliva. After 7 days, the tooth wear was evaluated using contact profilometry (μm). The experimental toothpastes with NaF, TiF4, SnF2, and Pro-Health showed a significant reduction in enamel wear (between 42% and 54%). Pro-Health also significantly reduced the dentin wear. The toothpastes with SnF2/NaF and TiF4/NaF showed the best results in the reduction of enamel wear (62–70%) as well as TiF4, SnF2, SnF2/NaF, and TiF4/NaF for dentin wear (64–79%) (P toothpastes containing both conventional and metal fluoride seem to be promising in reducing tooth wear. PMID:23258978

  13. Shoe heel abrasion and its possible biomechanical cause: a transversal study with infantry recruits.

    Science.gov (United States)

    Baumfeld, Daniel; Raduan, Fernando C; Macedo, Benjamim; Silva, Thiago Alexandre Alves; Baumfeld, Tiago; Favato, Danilo Fabrino; de Andrade, Marco Antonio Percope; Nery, Caio

    2015-11-19

    Excessive shoe heel abrasion is of concern to patients and shoe manufacturers, but little scientific information is available about this feature and its possible causes. The purpose of this study was to relate this phenomenon with biomechanical factors that could predispose to shoe heel abrasion. Ninety-seven recruits (median age 25) were enrolled in this study. Shoe abrasion was assessed manually with a metric plastic tape on the posterior part of the heel that comes in contact with the ground. The number of sprains, foot alignment, and calf muscle shortening (Silfverskiold test) was also assessed in order to relate it with shoe heel abrasion. After using our exclusion criteria, 86 recruits and 172 were considered for this study. The most common abrasion site was the lateral portion of the heel surface (50 %). Forty-four percent of the participants had neutral hind-foot alignment and 39 % had valgus alignment. Twenty-six (30 %) patients have had previous ankle or foot sprains. Neutral foot was related with less calf muscle shortening. On the other hand, valgus hind-foot alignment was more associated with Achilles shortening (p outsole abrasion with its possible biomechanical cause in order to predict and treat possible associated injuries.

  14. Comparison of methods for quantifying dental wear caused by erosion and abrasion.

    Science.gov (United States)

    Passos, Vanara F; Melo, Mary A S; Vasconcellos, Andréa Araújo; Rodrigues, Lidiany K A; Santiago, Sérgio L

    2013-02-01

    Various methods have been applied to evaluate the effect of erosion and abrasion. So, the aim of this study was to check the applicability of stylus profilometry (SP), surface hardness (SH) and focus-variation 3D microscopy (FVM) to the analysis of human enamel and dentin subjected to erosion/abrasion. The samples were randomly allocated into four groups (n = 10): G1-enamel/erosion, G2-enamel/erosion plus abrasion, G3-dentin/erosion, and G4-dentin/erosion plus abrasion. The specimens were selected by their surface hardness, and they were subjected to cycles of demineralization (Coca-Cola®-60 s) and remineralization (artificial saliva-60 min). For groups G2 and G4, the remineralization procedures were followed by toothbrushing (150 strokes). The above cycle was repeated 3×/day during 5 days. The samples were assessed using SH, SP, and FVM. For each substrate, the groups were compared using an unpaired t-test, and Pearson correlation coefficients were calculated (α = 5%). For enamel, both profilometry technique showed greater surface loss when the erosion and abrasion processes were combined (P dental substrate. SP was not sufficiently sensitive to measure the effects on dentin of erosion or erosion/abrasion. However, SP, FVM and SH were adequate for the detection of tissue loss and demineralization in enamel. Copyright © 2012 Wiley Periodicals, Inc.

  15. Knockdown and lethal effects of eight commercial nonconventional and two pyrethroid insecticides against moderately permethrin-resistant adult bed bugs, Cimex lectularius (L.) (Hemiptera: Cimicidae)

    Science.gov (United States)

    The common bed bug, Cimex lectularius (L.) (Hemiptera: Cimicidae) is undergoing a rapid resurgence in the United States during the last decade which has created a notable pest management challenge largely because the pest has developed resistance against DDT, organophosphates, carbamates, and pyreth...

  16. Characterization of a multidrug-resistant Salmonella enterica serovar Heidelberg outbreak strain in commercial turkeys: colonization, transmission, and host transcriptional response

    Science.gov (United States)

    In recent years, multidrug-resistant (MDR) Salmonella enterica serovar Heidelberg has been associated with numerous human foodborne illness outbreaks due to consumption of poultry. For example, in 2011, an MDR S. Heidelberg outbreak associated with ground turkey sickened 136 individuals and resulted...

  17. Studies on broad spectrum corrosion resistant oxide coatings

    Indian Academy of Sciences (India)

    The corrosion resistant oxide coatings, developed and applied by the conventional vitreous enamelling techniques, showed superior resistance to a range of mineral acids at various strengths and temperatures, alkaline solutions, boiling water and chrome plating solutions. These coatings possess considerable abrasion ...

  18. The Mars Environmental Compatibility Assessment MECA Abrasion Tool

    Science.gov (United States)

    Kuhlman, K. R.; Anderson, M. S.; Hinde, B. D.; Hecht, M. H.; Pike, W. T.; Marshall, J.; Meloy, T. P.; Cobbly, T.

    1999-01-01

    The Mars Environmental Compatibility Assessment (MECA) experiment, an instrument suite to be flown on Mars Surveyor 2001, will include a tool for doing simple mineralogical scratch and streak tests on particles from the Martian regolith. The Abrasion Tool will be applied to particles that adhere to highly polished substrates of various hardnesses. Granular soil components will be subjected to a compressive force of about 3 N using a leaf spring. The spring will be applied with a paraffin actuator capable of a 0.76 mm throw to achieve a maximum displacement of about 7.5 mm at the tip of the tool. The pressure per grain will be dependent on the grain size, the number of grains that adhere to the substrate and the number of grains in compression. The pressure per particle is expected to be on the order of 100 MPa - 1 GPa. The MECA sample wheel containing the substrates will be rotated after the particles are placed in compression to produce scratches or pits. A primary goal of the Abrasion Tool is to identify quartz (Mohs' hardness = 7) using substrates of varying hardnesses. Quartz is considered hazardous to future human explorers of Mars because it can cause silicosis of the lungs if it is of respirable size. It is also hazardous to machinery, structures, and space suits because of its ability to abrade and scratch surfaces. Since large quantities of minerals harder than quartz are not expected, any scratches produced on polished quartz substrates might be reasonably attributed to quartz particles, although there may be minerals such as impact metamorphic diamond in the soils. Careful calibration of the tool will be necessary to ensure that grains are not overloaded; for example, a steel ball pressed into glass will produce a Hertzian fracture, even though it is softer than glass. Other minerals, such as magnetite (Mohs'hardness = 6.5) have been shown to scratch glass ceramics such as Zerodur (Mohs' hardness = 6.5). Thus, minerals can be differentiated: note that

  19. The Mars Environmental Compatibility Assessment (MECA) Abrasion Tool

    Science.gov (United States)

    Kuhlman, K. R.; Anderson, M. S.; Hinde, B. D.; Hecht, M. H.; Pike, W. T.; Marshall, J. R.; Meloy, T. P.

    1999-01-01

    The Mars Environmental Compatibility Assessment (MECA) experiment, an instrument suite to be flown on Mars Surveyor 2001, will include a tool for doing simple mineralogical scratch and streak tests on particles from the Martian regolith. The Abrasion Tool will be applied to particles that adhere themselves to highly polished substrates of various hardnesses. Granular soil components will be subjected to a compressive force of about 3 N using a leaf spring. The spring will be applied with a paraffin actuator capable of a 0.76 mm throw to achieve a maximum displacement of about 7.5 mm at the tip of the tool. The pressure per grain will be dependent on the grain size, the number of grains that adhere to the substrate and the number of grains in compression. The pressure per particle is expected to be on the order of 100 MPa - 1 GPa. The MECA sample wheel containing the substrates will be rotated after the particles are placed in compression to produce scratches or pits. A primary goal of the Abrasion Tool is to identify quartz (Mohs' hardness = 7) using substrates of varying hardnesses. Quartz is considered hazardous to future human explorers of Mars because it can cause silicosis of the lungs if it is of respirable size. It is also hazardous to machinery, structures, and space suits because of its ability to abrade and scratch surfaces. Since large quantities of minerals harder than quartz are not expected, any scratches produced on polished quartz substrates might be reasonably attributed to quartz particles, although there may be minerals such as impact metamorphic diamond in the soils. Careful calibration of the tool will be necessary to ensure that grains are not overloaded; for example, a steel ball pressed into glass will produce a Hertzian fracture, even though it is softer than glass. Other minerals, such as magnetite (Mohs' hardness = 6.5) have been shown to scratch glass ceramics such as Zerodur (Mohs' hardness = 6.5). Thus, minerals can be differentiated

  20. A Study on Campylobacter jejuni and Campylobacter coli through Commercial Broiler Production Chains in Thailand: Antimicrobial Resistance, the Characterization of DNA Gyrase Subunit A Mutation, and Genetic Diversity by Flagellin A Gene Restriction Fragment Length Polymorphism.

    Science.gov (United States)

    Thomrongsuwannakij, Thotsapol; Blackall, Patrick J; Chansiripornchai, Niwat

    2017-06-01

    Contaminated poultry meat is regarded as the main source of human campylobacteriosis. During September 2014 and February 2015, breeder flocks, hatcheries, and broiler farms from two chicken production chains were investigated chronologically. Five commercial breeder flocks (Breeder Flocks 1-5), two hatcheries (Hatcheries A and B), and five broiler flocks (Broiler Flocks 1-5) were sampled in this study. Campylobacter colonization of both breeder and broiler flocks was determined from cloacal swabs and environmental samples (pan feeders, footwear, darkling beetles, flies, feed, and water). The eggs from the breeder flocks were followed to hatcheries. At the hatcheries, early embryonic deaths, egg trays, eggshells, hatchers, and water were investigated. Cloacal swabs were taken from broilers at Days 1, 14, and 28 (all broiler flocks), and either 35 (Broiler Flocks 1 and 2) or 43 (Broiler Flocks 3-5). Thirty-six Campylobacter jejuni and 94 Campylobacter coli isolates collected through two broiler production chains were tested by twofold agar dilution for their susceptibility to antimicrobial agents. Most Campylobacter isolates were multidrug resistant (MDR), defined as being resistant to three or more antimicrobial classes ( C. jejuni : 100%; C. coli : 98.9%), and exhibited high resistance to enrofloxacin ( C. jejuni : 100%; C. coli : 98.9%). The vast majority of C. coli were resistant to tetracycline (97.9%), trimethoprim-sulfamethoxazole (81.9%), and doxycycline (79.8%), but only 55.6%, 36.1%, and 50% of C. jejuni isolates revealed resistance to these antimicrobial agents, respectively. A selected subset of 24 C. jejuni and 24 C. coli were characterized for their mutations in the quinolone resistance determining region of the DNA gyrase subunit A gene by nucleotide sequence analysis. The Thr-86-Ile substitution (ACA-ATA in C. jejuni or ACT-ATT in C. coli ) was found in all isolates. Moreover, a total of 130 Campylobacter isolates were typed with the use of polymerase

  1. Combined effect of end-rounded versus tapered bristles and a dentifrice on plaque removal and gingival abrasion

    Directory of Open Access Journals (Sweden)

    Leonardo Stephan CAPOROSSI

    2016-01-01

    Full Text Available Abstract Two previous clinical studies evaluated the effect of end-rounded versus tapered bristles of soft manual brushes on the removal of plaque and gingival abrasion. However, the combined effect of an abrasive dentifrice on these outcomes has yet to be understood. The purpose of the present study was to compare the incidence of gingival abrasion and the degree of plaque removal obtained after the use of toothbrushes with tapered or end-rounded bristles in the presence or absence of an abrasive dentifrice. The study involved a randomized, single-blind, crossover model (n = 39 with a split-mouth design. Subjects were instructed to refrain from performing oral hygiene procedures for 72 hours. Quadrants were randomized and subjects brushed with both types of toothbrushes using a dentifrice (relative dentin abrasion = ± 160. Plaque and gingival abrasion were assessed before and after brushing. After 7 days, the experiment was repeated without the dentifrice. The average reduction in plaque scores and the average increase in the number of abrasion sites were assessed by repeated-measures ANOVA and Bonferroni’s post-hoc tests. End-rounded bristles removed significantly more plaque than tapered bristles, regardless of the use of a dentifrice. The dentifrice did not improve plaque removal. In the marginal area (cervical free gingiva, no difference in the incidence of gingival abrasion was detected between toothbrush types when used with a dentifrice (p ≥ 0.05. However, the dentifrice increased the incidence of abrasion (p < 0.001, irrespective of the toothbrush type tested. End-rounded bristles therefore removed plaque more effectively without causing a higher incidence of gingival abrasion when compared with tapered bristles. An abrasive dentifrice can increase the incidence of abrasion, and should be used with caution by individuals who are at risk of developing gingival recession.

  2. A profilometry-based dentifrice abrasion Method for V8 brushing machines. Part I: Introduction to RDA-PE.

    Science.gov (United States)

    White, Donald J; Schneiderman, Eva; Colón, Ellen; St John, Samuel

    2015-01-01

    This paper describes the development and standardization of a profilometry-based method for assessment of dentifrice abrasivity called Radioactive Dentin Abrasivity - Profilometry Equivalent (RDA-PE). Human dentine substrates are mounted in acrylic blocks of precise standardized dimensions, permitting mounting and brushing in V8 brushing machines. Dentin blocks are masked to create an area of "contact brushing." Brushing is carried out in V8 brushing machines and dentifrices are tested as slurries. An abrasive standard is prepared by diluting the ISO 11609 abrasivity reference calcium pyrophosphate abrasive into carboxymethyl cellulose/glycerin, just as in the RDA method. Following brushing, masked areas are removed and profilometric analysis is carried out on treated specimens. Assessments of average abrasion depth (contact or optical profilometry) are made. Inclusion of standard calcium pyrophosphate abrasive permits a direct RDA equivalent assessment of abrasion, which is characterized with profilometry as Depth test/Depth control x 100. Within the test, the maximum abrasivity standard of 250 can be created in situ simply by including a treatment group of standard abrasive with 2.5x number of brushing strokes. RDA-PE is enabled in large part by the availability of easy-to-use and well-standardized modern profilometers, but its use in V8 brushing machines is enabled by the unique specific conditions described herein. RDA-PE permits the evaluation of dentifrice abrasivity to dentin without the requirement of irradiated teeth and infrastructure for handling them. In direct comparisons, the RDA-PE method provides dentifrice abrasivity assessments comparable to the gold industry standard RDA technique.

  3. Effect of tooth brush abrasion and thermo-mechanical loading on direct and indirect veneer restorations.

    Science.gov (United States)

    Rosentritt, Martin; Sawaljanow, Alexander; Behr, Michael; Kolbeck, Carola; Preis, Verena

    2015-01-01

    This study investigated toothbrush abrasion and in vitro aging on ceramic (indirect technique) and composite veneers (direct technique). Identical composite and individual human incisors were restored with industrially preformed composite veneers, indirectly produced ceramic veneers, and direct composite restorations. Surface roughness was determined before and after tooth brushing. A 5-year period of oral service was simulated by thermal cycling and mechanical loading (TCML). After TCML, all specimens were examined with microscopy and scanning electron microscopy. Specimens without failures during TCML were loaded until failure. analysis of variance; Bonferroni's post hoc analysis, Kaplan-Meier-Log Rank test (α = 0.05). Tooth brushing yielded a non-significant increase (p = 0.560) in roughness in all materials (industrial veneer, 0.12+/-0.07 μm, direct restoration, 0.18+/-0.14 μm, ceramic, 0.35+/-0.16 μm). No significant differences in roughness could be determined between the materials, neither before nor after testing (p teeth, direct and preformed composite veneers on composite teeth showed no failures or damages. Two ceramic veneers showed cracking in the labial area. After TCML of human teeth, transmission microscopy indicated a facial crack in a ceramic veneer and chipping in the cervical area of a preformed veneer. Two direct composite veneers lost retention. No significantly different survival rates were found between the three veneer groups. Fracture force on human teeth varied between 527.8+/-132.4 N (ceramic), 478.3+/-165.4 N (preformed composite), and 605.0+/-263.5 N (direct composite). All materials revealed comparable wear resistance. Indirect ceramic, direct restorative composite, and preformed composite veneers showed comparable failure rates and satisfying longevity. The results indicate similar longevity of the chosen materials for veneer restorations.

  4. Frictional and heat resistance characteristics of coconut husk particle filled automotive brake pad

    Science.gov (United States)

    Bahari, Shahril Anuar; Chik, Mohd Syahrizul; Kassim, Masitah Abu; Som Said, Che Mohamad; Misnon, Mohd Iqbal; Mohamed, Zulkifli; Othman, Eliasidi Abu

    2012-06-01

    The objective of this study was to determine the friction and heat resistance characteristics of automotive brake pad composed with different sizes and percentages of coconut husk particle. The materials used were phenolic resin (phenol formaldehyde) as binder, copper, graphite and brass as friction producer/modifiers, magnesium oxide as abrasive material, steel and barium sulfate as reinforcement while coconut husk particle as filler. To obtain particle, the coconut husk was ground and dried to 3% moisture content. Then the coconut husk particle was screened using 80 mesh (to obtain coarse dust) and 100 mesh (to obtain fine dust). Different percentages of particle, such as 10 and 30% were used in the mixture of brake pad materials. Then the mixture was hot-pressed to produce brake pad. Chase machine was used to determine the friction coefficient in friction resistance testing, while thermogravimetric analyzer (TGA) machine was used to determine the heat decomposition values in heat resistance testing. Results showed that brake pad with 100 mesh and 10% composition of coconut husk particle showed the highest friction coefficient. For heat resistance, brake pad with 100 mesh and 30% composition of coconut husk dust showed the highest decomposition temperature, due to the high percentage of coconut husk particle in the composition, thus increased the thermal stability. As a comparison, brake pad composed with coconut husk particle showed better heat resistance results than commercial brake pad.

  5. Advanced Wear-resistant Nanocomposites for Increased Energy Efficiency

    Energy Technology Data Exchange (ETDEWEB)

    Cook, B. A.; Harringa, J. L.; Russel, A. M.

    2012-12-01

    This report summarizes the work performed by an Ames-led project team under a 4-year DOE-ITP sponsored project titled, 'Advanced Wear-resistant Nanocomposites for Increased Energy Efficiency.' The Report serves as the project deliverable for the CPS agreement number 15015. The purpose of this project was to develop and commercialize a family of lightweight, bulk composite materials that are highly resistant to degradation by erosive and abrasive wear. These materials, based on AlMgB{sub 14}, are projected to save over 30 TBtu of energy per year when fully implemented in industrial applications, with the associated environmental benefits of eliminating the burning of 1.5 M tons/yr of coal and averting the release of 4.2 M tons/yr of CO{sub 2} into the air. This program targeted applications in the mining, drilling, machining, and dry erosion applications as key platforms for initial commercialization, which includes some of the most severe wear conditions in industry. Production-scale manufacturing of this technology has begun through a start-up company, NewTech Ceramics (NTC). This project included providing technical support to NTC in order to facilitate cost-effective mass production of the wear-resistant boride components. Resolution of issues related to processing scale-up, reduction in energy intensity during processing, and improving the quality and performance of the composites, without adding to the cost of processing were among the primary technical focus areas of this program. Compositional refinements were also investigated in order to achieve the maximum wear resistance. In addition, synthesis of large-scale, single-phase AlMgB{sub 14} powder was conducted for use as PVD sputtering targets for nanocoating applications.

  6. Effect of internal limiting membrane abrasion on retinal tissues in macular holes.

    Science.gov (United States)

    Almeida, David R P; Chin, Eric K; Tarantola, Ryan M; Folk, James C; Boldt, H Culver; Skeie, Jessica M; Mullins, Robert F; Russell, Stephen R; Mahajan, Vinit B

    2015-05-01

    The purpose of this study was to identify the structural and histological effects of a Tano diamond-dusted membrane scraper (DDMS) on the retinal surface after internal limiting membrane (ILM) abrasion in macular hole surgery. Institutional experimental study was performed in 11 eyes. All eyes underwent ILM abrasion in the operating room with a DDMS for macular hole repair as an alternative to traditional ILM peeling. Three human donor eyes underwent an identical procedure in the laboratory. Retinal tissues were removed by ILM abrasion with a DDMS during vitrectomy for macular hole repair and retinal tissues remaining in human donor eyes. Main outcome measures were microscopic and immunohistological characteristics of instrument tip tissues and retinal structure after ILM abrasion. The tips of the Tano DDMS showed evidence of cellular membranes and ILM removal. The retinas showed distinct areas of lamellar ILM removal without penetration of the retinal nerve fiber layer (RNFL). Application of the Tano DDMS instrument is sufficient to remove membranes from the surface of the ILM and layers of the ILM without disruption of the underlying RNFL. Internal limiting membrane abrasion can be a useful and effective alternative to complete ILM removal for macular surgery.

  7. A Study on Postmortem Wound Dating by Gross and Histopathological Examination of Abrasions.

    Science.gov (United States)

    Vinay, Javaregowda; Harish, Sathyanarayana; Mangala, Gouri S R; Hugar, Basappa S

    2017-06-01

    Abrasions are the most common blunt force injuries. The precise dating of injury is extremely important in forensic medicine practice. As we know, the wound healing occurs in well-orchestrated sequence, consisting of inflammation, proliferation, and maturation.A study of occurrence of such phases will help in understanding the sequence of events in wound healing. In this context, this study of wound dating from gross and microscopic level was taken. Postmortem study of wound dating by gross and histopathological examination of abrasions was carried out in the Department of Forensic Medicine, in M.S. Ramaiah Medical College. A total of 101 abrasions were correlated to time frame the occurrence of different gross changes and microscopic changes that follow the blunt trauma. Abrasions ranging from 0 hour to a maximum of 45 days were studied. The gross changes of abrasions were in correlation with the microscopic changes; however, the role of the comorbid conditions is significant because the results showed variations with respect to healing process. This study signifies that, if naked eye examination is studied along with histopathological examination, the reliability and accuracy of dating of wound increase. Whenever accurate determination of age is required, the autopsy surgeon can subject the samples for histopathological examination and correlate before opining the age of injury.

  8. Reducing the surface roughness of dental acrylic resins by using an eggshell abrasive material.

    Science.gov (United States)

    Onwubu, Stanley C; Vahed, Anisa; Singh, Shalini; Kanny, Krishnan M

    2017-02-01

    Excessive surface roughness of denture base resins adversely impacts oral health. The purpose of this in vitro study was to examine the abrasive potential of eggshell powder in reducing the surface roughness of denture base resins. Thirty poly(methyl methacrylate) specimens were fabricated and polished with eggshell powders of different particle sizes and with pumice. The average surface roughness (Ra) after polishing was measured with a profilometer. Scanning electron microscope and optical electron microscope techniques were used to assess the surface roughness morphology of the specimens. ANOVA was used to analyze the Ra values. The Tukey honest significant differences and Bonferroni tests were used to identify differences between the 2 abrasive materials (α=.05). Significant differences in the Ra values were observed between the fine and medium eggshell powder abrasives (P.05). Specimens polished with pumice had the highest Ra values, whereas specimens polished with the fine eggshell powder abrasive had the lowest Ra values. By connecting the Ra values to the threshold limit value of 0.2 μm, eggshell powder abrasive finished denture acrylic resin surfaces better than pumice. Copyright © 2016 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

  9. Comparative Evaluation of Gingival Depigmentation using Tetrafluoroethane Cryosurgery and Gingival Abrasion Technique: Two Years Follow Up.

    Science.gov (United States)

    Kumar, Santhosh; Bhat, G Subraya; Bhat, K Mahalinga

    2013-02-01

    A comparative evaluation of the gingival depigmentation by using Tetrafluoroethane cryosurgery and the gingival abrasion technique - 2 years of follow up. Ten systemically healthy patients who were aged 18 to 36 years were selected for the study. Tetrafluoroethane was used for the cryosurgical depigmentation and the gingival abrasion technique used a coarse flame shaped bur. The presence or absence of pigmentation was tabulated, based on the GPI (Gingival Pigmentation Index). For the statistical analysis, Freidman's test was used. The keratinization was completed within a week after the application of the cryogen and about 10 days after the gingival abrasion technique was done. The statistical analysis which was done after 90th, 180th days and 2 years. The p-value which was obtained (pgingival abrasion. During the follow up period, no side effects were seen for both the techniques and the improved aesthetics was maintained upto 2 years. The use of cryogen Tetrafluoroethane is easy, practical and inexpensive as compared to gingival abrasion, due to its high rate of recurrence. Hence, it is more acceptable to the patients and the operator. Further studies are needed to assess the long term effectiveness of the cryosurgical method of depigmentation.

  10. Experimental Study of the Ultrasonic Vibration-Assisted Abrasive Waterjet Micromachining the Quartz Glass

    Directory of Open Access Journals (Sweden)

    Rongguo Hou

    2018-01-01

    Full Text Available The ultrasonic vibration is used to enhance the capability of the abrasive water micromachining glass. And, the ultrasonic vibration is activated on the abrasive waterjet nozzle. The quality of the flow is improved, and the velocity of the abrasive is increased because of the addition of the ultrasonic energy. The relevant experimental results indicate that the erosion depth and the material volume removal of the glass are obviously increased when ultrasonic vibration is working. As for the influence of process parameters on the material removal of the glass such as vibration amplitude, system pressure, distance of the standoff, and abrasive size, the experimental results indicate that the system pressure and vibration contribute greatly to the glass material removal. Also, the erosion depth and the volume of material removal are increased with the increase in the vibration amplitude and system pressure. There are some uplifts found at the edge of erosion pit. Then, it can be inferred that the plastic method is an important material removal method during the machining process of ultrasonic vibration-assisted abrasive waterjet.

  11. Genetic diversity and antimicrobial resistance among isolates of Escherichia coli O157: H7 from feces and hides of super-shedders and low-shedding pen-mates in two commercial beef feedlots

    Directory of Open Access Journals (Sweden)

    Stanford Kim

    2012-09-01

    Full Text Available Abstract Background Cattle shedding at least 104 CFU Escherichia coli O157:H7/g feces are described as super-shedders and have been shown to increase transmission of E. coli O157:H7 to other cattle in feedlots. This study investigated relationships among fecal isolates from super-shedders (n = 162, perineal hide swab isolates (PS from super-shedders (n = 137 and fecal isolates from low-shedder (4 CFU/g feces pen-mates (n = 496 using pulsed-field gel electrophoresis (PFGE. A subsample of these fecal isolates (n = 474 was tested for antimicrobial resistance. Isolates of E. coli O157:H7 were obtained from cattle in pens (avg. 181 head at 2 commercial feedlots in southern Alberta with each steer sampled at entry to the feedlot and prior to slaughter. Results Only 1 steer maintained super-shedder status at both samplings, although approximately 30% of super-shedders in sampling 1 had low-shedder status at sampling 2. A total of 85 restriction endonuclease digestion clusters (REPC; 90% or greater similarity and 86 unique isolates (P = 0.94. Only 2/21 super-shedders had fecal isolates in the same REPC at both samplings. Fecal and PS isolates from individual super-shedders generally belonged to different REPCs, although fecal isolates of E. coli O157:H7 from super- and low-shedders showed greater similarity (P P = 0.69, although all super-shedder isolates with antimicrobial resistance (n = 3 were resistant to multiple antimicrobials. Conclusions Super-shedders did not have increased antimicrobial resistance compared to low-shedder pen mates. Our data demonstrated that PFGE profiles of individual super-shedders varied over time and that only 1/162 steers remained a super-shedder at 2 samplings. In these two commercial feedlots, PFGE subtypes of E. coli O157:H7 from fecal isolates of super- and low-shedders were frequently different as were subtypes of fecal and perineal hide isolates from super-shedders.

  12. The effects of a commercially available botanical supplement on strength, body composition, power output, and hormonal profiles in resistance-trained males

    Directory of Open Access Journals (Sweden)

    Kreider Richard

    2010-10-01

    Full Text Available Abstract Background Fenugreek (Trigonella foenum-graecum is a leguminous, annual plant originating in India and North Africa. In recent years Fenugreek has been touted as an ergogenic aid. The purpose of this study was to evaluate the effects of Fenugreek supplementation on strength and body composition. Methods 49 Resistance trained men were matched according to body weight and randomly assigned to ingest in a double blind manner capsules containing 500 mg of a placebo (N = 23, 20 ± 1.9 years, 178 ± 6.3 cm, 85 ± 12.7 kg, 17 ± 5.6 %BF or Fenugreek (N = 26, 21 ± 2.8 years, 178 ± 6 cm, 90 ± 18.2 kg, 19.3 ± 8.4 %BF. Subjects participated in a supervised 4-day per week periodized resistance-training program split into two upper and two lower extremity workouts per week for a total of 8-weeks. At 0, 4, and 8-weeks, subjects underwent hydrodensiometery body composition, 1-RM strength, muscle endurance, and anaerobic capacity testing. Data were analyzed using repeated measures ANOVA and are presented as mean ± SD changes from baseline after 60-days. Results No significant differences (p > 0.05 between groups were noted for training volume. Significant group × time interaction effects were observed among groups in changes in body fat (FEN: -2.3 ± 1.4%BF; PL: -0.39 ± 1.6 %BF, p 0.05. Conclusion It is concluded that 500 mg of this proprietary Fenugreek extraction had a significant impact on both upper- and lower-body strength and body composition in comparison to placebo in a double blind controlled trial. These changes were obtained with no clinical side effects.

  13. Commercial applications

    Science.gov (United States)

    The near term (one to five year) needs of domestic and foreign commercial suppliers of radiochemicals and radiopharmaceuticals for electromagnetically separated stable isotopes are assessed. Only isotopes purchased to make products for sale and profit are considered. Radiopharmaceuticals produced from enriched stable isotopes supplied by the Calutron facility at ORNL are used in about 600,000 medical procedures each year in the United States. A temporary or permanent disruption of the supply of stable isotopes to the domestic radiopharmaceutical industry could curtail, if not eliminate, the use of such diagnostic procedures as the thallium heart scan, the gallium cancer scan, the gallium abscess scan, and the low radiation dose thyroid scan. An alternative source of enriched stable isotopes exist in the USSR. Alternative starting materials could, in theory, eventually be developed for both the thallium and gallium scans. The development of a new technology for these purposes, however, would take at least five years and would be expensive. Hence, any disruption of the supply of enriched isotopes from ORNL and the resulting unavailability of critical nuclear medicine procedures would have a dramatic negative effect on the level of health care in the United States.

  14. The rock abrasion record at Gale Crater: Mars Science Laboratory results from Bradbury Landing to Rocknest

    Science.gov (United States)

    Bridges, N.T.; Calef, F.J.; Hallett, B.W.; Herkenhoff, Kenneth E.; Lanza, N.L.; Le Mouélic, S.; Newman, C.E.; Blaney, D.L.; de Pablo, M.A.; Kocurek, G.A.; Langevin, Y.; Lewis, K.W.; Mangold, N.; Maurice, S.; Meslin, P.-Y.; Pinet, P.; Renno, N.O.; Rice, CM.S.; Richardson, M.E.; Sautter, V.; Sletten, R.S.; Wiens, R.C.; Yingst, R.A.

    2014-01-01

    Ventifacts, rocks abraded by wind-borne particles, are found in Gale Crater, Mars. In the eastward drive from “Bradbury Landing” to “Rocknest,” they account for about half of the float and outcrop seen by Curiosity's cameras. Many are faceted and exhibit abrasion textures found at a range of scales, from submillimeter lineations to centimeter-scale facets, scallops, flutes, and grooves. The drive path geometry in the first 100 sols of the mission emphasized the identification of abrasion facets and textures formed by westerly flow. This upwind direction is inconsistent with predictions based on models and the orientation of regional dunes, suggesting that these ventifact features formed from very rare high-speed winds. The absence of active sand and evidence for deflation in the area indicates that most of the ventifacts are fossil features experiencing little abrasion today.

  15. Brushing force of manual and sonic toothbrushes affects dental hard tissue abrasion.

    Science.gov (United States)

    Wiegand, Annette; Burkhard, John Patrik Matthias; Eggmann, Florin; Attin, Thomas

    2013-04-01

    This study aimed to determine the brushing forces applied during in vivo toothbrushing with manual and sonic toothbrushes and to analyse the effect of these brushing forces on abrasion of sound and eroded enamel and dentin in vitro. Brushing forces of a manual and two sonic toothbrushes (low and high frequency mode) were measured in 27 adults before and after instruction of the respective brushing technique and statistically analysed by repeated measures analysis of variance (ANOVA). In the in vitro experiment, sound and eroded enamel and dentin specimens (each subgroup n = 12) were brushed in an automatic brushing machine with the respective brushing forces using a fluoridated toothpaste slurry. Abrasion was determined by profilometry and statistically analysed by one-way ANOVA. Average brushing force of the manual toothbrush (1.6 ± 0.3 N) was significantly higher than for the sonic toothbrushes (0.9 ± 0.2 N), which were not significantly different from each other. Brushing force prior and after instruction of the brushing technique was not significantly different. The manual toothbrush caused highest abrasion of sound and eroded dentin, but lowest on sound enamel. No significant differences were detected on eroded enamel. Brushing forces of manual and sonic toothbrushes are different and affect their abrasive capacity. Patients with severe tooth wear and exposed and/or eroded dentin surfaces should use sonic toothbrushes to reduce abrasion, while patients without tooth wear or with erosive lesions confining only to enamel do not benefit from sonic toothbrushes with regard to abrasion.

  16. Design of erosion/abrasion studies--insights and rational concepts.

    Science.gov (United States)

    Wiegand, Annette; Attin, Thomas

    2011-01-01

    In vitro and in situ studies modelling the wear of dental hard tissues due to erosion and abrasion are characterised by a high variation in study designs and experimental parameters. Based on a summary of the existing protocols, the present review aimed to describe and discuss the parameters which must be carefully considered in erosion-abrasion research, especially when it is intended to simulate clinical conditions. Experimental characteristics and parameters were retrieved from a total of 42 in vitro and 20 in situ studies. The key experimental characteristics included parameters of erosion (duration and pH) and abrasion (duration, kinds of toothbrush and toothpaste, brushing force, and time point) as well as co-factors (e.g. dental hard tissue). The majority of studies used models with alternating erosion/abrasion treatments intended to simulate clinical conditions, while other studies exaggerated clinical conditions intentionally, often using only a single erosion/abrasion treatment. Both in vitro and in situ models shared a high level of standardisation, but several studies showed a trend to severe erosion (e.g. >5 min/cycle) or extensive brushing (e.g. >100 brushing strokes/cycle) at a high frequency and repetition rate. Thus, studies often tend to produce a higher amount of wear than in the clinical situation, especially as modifying biological factors (e.g. the dilution of the erosive solution by saliva and the protective effect of the pellicle) cannot be simulated adequately. With respect to the existing models, it seems advisable to diminish duration and frequency of erosion and abrasion to more realistic clinical conditions when the everyday situation is to be simulated. Experimental parameters must be chosen with care to ensure that the problem is investigated in an appropriate mode at standardised conditions and with adequate measuring systems to allow prediction of clinical outcomes. Copyright © 2011 S. Karger AG, Basel.

  17. Impact Capacity Reduction in Railway Prestressed Concrete Sleepers with Surface Abrasions

    Science.gov (United States)

    Ngamkhanong, Chayut; Li, Dan; Kaewunruen, Sakdirat

    2017-10-01

    Railway sleepers (also called ‘railroad tie’ in North America) embedded in ballasted railway tracks are a main part of railway track structures. Its important role is to transfer the loads evenly from the rails to a wider area of ballast bed and to secure rail gauge and enable safe passages of rolling stocks. By nature, railway infrastructure is nonlinear, evidenced by its behaviours, geometry and alignment, wheel-rail contact and operational parameters such as tractive efforts. Based on our critical review, the dynamic behaviour of railway sleepers has not been fully investigated, especially when the sleepers are deteriorated by excessive wears. In fact, the ballast angularity causes differential abrasions on the soffit or bottom surface of sleepers (especially at railseat zone). Furthermore, in sharp curves and rapid gradient change, longitudinal and lateral dynamics of rails increase the likelihood of railseat abrasions in concrete sleepers due to the unbalanced loading conditions. This paper presents a structural capacity of concrete sleepers under dynamic transient loading. The modified compression field theory for ultimate strength design of concrete sleepers under impact loading will be highlighted in this study. The influences of surface abrasions, including surface abrasion and soffit abrasion, on the dynamic behaviour of prestressed concrete sleepers, are firstly highlighted. The outcome of this study will improve the rail maintenance and inspection criteria in order to establish appropriate and sensible remote track condition monitoring network in practice. Moreover, this study will also improve the understanding of the fundamental dynamic behaviour of prestressed concrete sleepers with surface abrasions. The insight into these behaviours will not only improve safety and reliability of railway infrastructure but will enhance the structural safety of other concrete structures.

  18. Abrasion Testing of Candidate Outer Layer Fabrics for Lunar EVA Space Suits

    Science.gov (United States)

    Mitchell, Kathryn C.

    2010-01-01

    During the Apollo program, the space suit outer layer fabrics were badly abraded after just a few Extravehicular Activities (EVAs). For example, the Apollo 12 commander reported abrasive wear on the boots, which penetrated the outer layer fabric into the thermal protection layers after less than eight hours of surface operations. Current plans for the Constellation Space Suit Element require the space suits to support hundreds of hours of EVA on the Lunar surface, creating a challenge for space suit designers to utilize materials advances made over the last forty years and improve upon the space suit fabrics used in the Apollo program. A test methodology has been developed by the NASA Johnson Space Center Crew and Thermal Systems Division for establishing comparative abrasion wear characteristics between various candidate space suit outer layer fabrics. The abrasion test method incorporates a large rotary drum tumbler with rocks and loose lunar simulant material to induce abrasion in fabric test cylinder elements, representative of what might occur during long term planetary surface EVAs. Preliminary materials screening activities were conducted to determine the degree of wear on representative space suit outer layer materials and the corresponding dust permeation encountered between subsequent sub -layers of thermal protective materials when exposed to a simulated worst case eight hour EVA. The test method was used to provide a preliminary evaluation of four candidate outer layer fabrics for future planetary surface space suit applications. This Paper provides a review of previous abrasion studies on space suit fabrics, details the methodologies used for abrasion testing in this particular study, and shares the results and conclusions of the testing.

  19. ANN & ANFIS Models for Prediction of Abrasive Wear of 3105 Aluminium Alloy with Polyurethane Coating

    Directory of Open Access Journals (Sweden)

    H. Alimam

    2016-06-01

    Full Text Available The quest for safety and reliability has increased significantly after Industrial revolution, so is the case for coating industries. In this paper 3105 Aluminium alloy sheet is coated with organic polyurethane coating. After the implementation of coating, various processes are undergone to check its reliability under elevated conditions. ANN & ANFIS model were developed and trained with an objective to find abrasive wear during the process. ANN & ANFIS model were compared with the experimental results. It is observed that the abrasive wear of a coated specimen can be predicted accurately and precisely using ANN and ANFIS models.

  20. Experience with bandage contact lenses for the treatment of corneal abrasions in a combat environment.

    Science.gov (United States)

    Buglisi, Joseph A; Knoop, Kevin J; Levsky, Marc E; Euwema, Michael

    2007-04-01

    Corneal abrasions are a common result of eye trauma. Although they usually heal well with conservative therapy, they still tend to be a source of morbidity, in terms of pain and lost work time. We reviewed 15 cases in which a bandage contact lens was used as the primary treatment for corneal abrasions in an austere environment. We found that the lenses performed well, except for patients who had undisclosed risk factors for corneal ulcers at the outset. When used for carefully selected patients, bandage contact lenses may be a highly effective treatment modality that allows for rapid return to duty.

  1. Interplay between experimental dental pellicles and stannous-containing toothpaste on dental erosion-abrasion.

    Science.gov (United States)

    Hara, A T; Lippert, F; Zero, D T

    2013-01-01

    The interaction between stannous-containing dentifrice slurry and experimentally formed pellicles was investigated on enamel and root dentin using an erosion-remineralization-abrasion cycling model. The remineralizing solutions contained no proteins (negative control), mucin, casein, mucin + casein or albumin, for experimental pellicle formation. Toothbrushing was performed with fluoride toothpaste, with (TP + Sn) and without (TP) 3,500 ppm Sn. TP + Sn reduced surface loss for both enamel and root dentin (p dental erosion-abrasion protection. A similar trend was observed for root dentin, although less pronounced. Copyright © 2013 S. Karger AG, Basel.

  2. Effects of enamel abrasion, salivary pellicle, and measurement angle on the optical assessment of dental erosion

    OpenAIRE

    Lussi, Adrian; Bossen, Anke; Höschele, Christoph; Beyeler, Barbara; Megert, Brigitte; Meier, Christoph; Rakhmatullina, Ekaterina

    2012-01-01

    The present study assessed the effects of abrasion, salivary proteins, and measurement angle on the quantification of early dental erosion by the analysis of reflection intensities from enamel. Enamel from 184 caries-free human molars was used for in vitro erosion in citric acid (pH 3.6). Abrasion of the eroded enamel resulted in a 6% to 14% increase in the specular reflection intensity compared to only eroded enamel, and the reflection increase depended on the erosion degree. Nevertheless, m...

  3. The measurement of the velocity of abrasive particlesat the suction part of the cutting head

    Czech Academy of Sciences Publication Activity Database

    Foldyna, Josef; Zeleňák, Michal; Klich, Jiří; Hlaváček, Petr; Sitek, Libor; Říha, Zdeněk

    2015-01-01

    Roč. 22, č. 6 (2015), s. 1441-1446 ISSN 1330-3651. [Vodní paprsek 2013 - výzkum, vývoj, aplikace. Soláň, Karolinka, 22.10.2013-24.10.2013] R&D Projects: GA MŠk ED2.1.00/03.0082; GA MŠk(CZ) LO1406 Institutional support: RVO:68145535 Keywords : abrasive water jet * velocity of abrasive particles * shadowgraphy Subject RIV: JQ - Machines ; Tools Impact factor: 0.464, year: 2015 http://www.tehnicki-vjesnik.com/web/public/archive

  4. Development and validation of an alternative disturbed skin model by mechanical abrasion to study drug penetration

    Directory of Open Access Journals (Sweden)

    P. Schlupp

    2014-01-01

    Skin permeation of the three substances was increased in tape-stripped and abraded skin compared to untreated skin due to the reduced barrier integrity. Enhancement of drug uptake was highest for the most hydrophilic substance, caffeine, followed by sorbic acid and lipophilic testosterone. No significant difference in drug uptake studies was observed between the new abrasion method with an aluminum-coated sponge and the tape-stripping method. The obtained results demonstrate that this abrasion method is an alternative way to achieve a disturbed skin barrier for drug and chemical uptake studies.

  5. An evaluation of the associations of parameters related to the fall of Varroa destructor (Acari: Varroidae) from commercial honey bee (Hymenoptera: Apidae) colonies as tools for selective breeding for mite resistance.

    Science.gov (United States)

    Rinderer, Thomas E; De Guzman, Lilia I; Frake, Amanda M; Tarver, Matthew R; Khongphinitbunjong, Kitiphong

    2014-04-01

    Varroa destructor (Anderson and Trueman) trapped on bottom boards were assessed as indirect measurements of colony mite population differences and potential indicators of mite resistance in commercial colonies of Russian and Italian honey bees (Apis mellifera L.) by using 35 candidate measurements. Measurements included numbers of damaged and nondamaged younger mites, nymphs, damaged and nondamaged older mites, fresh mites, and all mites, each as a proportion of total mites in the colonies and as a proportion of all trapped mites or all trapped fresh mites. Several measurements differed strongly between the stocks, suggesting that the detailed characteristics of trapped mites may reflect the operation of resistance mechanisms in the Russian honey bees. Regression analyses were used to determine the relationships of these candidate measurements with the number of mites in the colonies. The largest positive regressions differed for the two stocks (Italian honey bees: trapped mites and trapped younger mites; Russian honey bees: trapped younger mites and trapped fresh mites). Also, the regressions for Italian honey bees were substantially stronger. The largest negative regressions with colony mites for both stocks were for the proportion of older mites out of all trapped mites. Although these regressions were statistically significant and consistent with those previously reported, they were weaker than those previously reported. The numbers of mites in the colonies were low, especially in the Russian honey bee colonies, which may have negatively influenced the precision of the regressions.

  6. Development of a two-body wet abrasion test method with attention to the effects of reused abradant

    Energy Technology Data Exchange (ETDEWEB)

    Blau, Peter Julian [ORNL; Dehoff, Ryan R [ORNL

    2012-01-01

    Abrasive wear is among the most common and costliest causes for material wastage, and it occurs in many forms. A simple method has been developed to quantify the response of metals and alloys to two-body wet abrasion. A metallographic polishing machine was modified to create a disk-on-flat sliding test rig. Adhesive-backed SiC grinding papers were used under fixed load and speed to rank the abrasive wear of seven alloy steels, some of which are candidates for drill cones for geothermal drilling. Standardized two-body abrasion tests, like those described in ASTM G132, feed unused abrasive into the contact; however, the current work investigated whether useful rankings could still be obtained with a simpler testing configuration in which specimens repeatedly slide on the same wear path under water-lubricated conditions. Tests using abrasive grit sizes of 120 and 180 resulted in the same relative ranking of the alloys although the coarser grit produced more total wear. Wear decreased when the same abrasive disk was re-used for up to five runs, but the relative rankings of the steels remained the same. This procedure was presented to ASTM Committee G2 on Wear and Erosion as a potential standard test for wet two-body abrasive wear.

  7. Highly selective chemical mechanical polishing of Si3N4 over SiO2 using advanced silica abrasive

    Science.gov (United States)

    Bae, KiHo; Baek, Kye Hyun; Kim, JaeSeok; Kim, Hoyoung; Yoon, Bo Un; Kim, Jae Jeong

    2017-05-01

    Highly selective chemical mechanical polishing (CMP) of Si3N4 over SiO2 is achieved by using a modified silica abrasive. Controlling the removal rate of Si3N4/SiO2, chemical reaction is a dominant factor for ceria abrasive, but physical force such as repulsion/attraction is a primary one for silica abrasive. In order to maximize mechanical action in CMP process using silica slurry, we modified the surface charge of silica abrasive into having more negative charge, which resulting in -50 mV of zeta potential in a low pH (< 3.0) slurry. This strong negative zeta potential of the modified silica abrasive enables enhancing attractive forces to Si3N4 and repulsive forces to SiO2 in a low pH environment. In addition, a cocoon shape silica abrasive shows 3 times higher Si3N4 RR than a spherical shape one. Consequently, selectivity of Si3N4 over SiO2 reaches 95.0, which is significantly improved from 0.0167 in the conventional silica abrasive case. When this modified silicon abrasive and the optimum pH condition are applied, in-chip uniformity at various pattern densities of Si3N4 (0, 12, and 32%) turns out to be well controlled under 100 Å. This result is an acceptable level for our semiconductor device integration.

  8. Relationship between handedness and toothbrush-related cervical dental abrasion in left- and right-handed individuals

    National Research Council Canada - National Science Library

    Özgöz, Mehmet; Arabaci, Taner; Sümbüllü, Mehmet Akif; Demir, Turgut

    2010-01-01

    ... bacterial plaque from tooth surfaces. However, cervical dental abrasion and gingival recession in the vestibule area are mostly caused by improper tooth-brushing. 5,6 Problems with brushing are commonly related to technique, duration, daily frequency, and the force applied when brushing. 7–10 In addition, traumatic cervical dental abrasion caused ...

  9. Analysis of the structure of castings made from chromium white cast iron resistant to abrasive wear

    Directory of Open Access Journals (Sweden)

    D. Kopyciński

    2009-10-01

    Full Text Available It has been proved that an addition of boron carbide and disintegrated steel scrap introduced as an inoculant to the chromium white cast iron changes the structure of castings. The said operation increases the number of crystallization nuclei for dendrites of the primary austenite. In this case, the iron particles act as substrates for the nucleation of primary austenite due to a similar crystallographic lattice. The more numerous are the dendrites of primary austenite and the structure more refined and the mechanical properties higher. Castings after B4C inoculation revealed a different structure of fine grained fracture. Primary precipitates of chromium carbide also appeared, reducing the mechanical properties of as-cast parts. Properly established heat treatment regime makes chromium iron castings regain their, originally high, mechanical properties.

  10. Application of polymer-powder slurry for fabrication of abrasion resistant coatings on tool materials

    OpenAIRE

    G. Matula

    2011-01-01

    Purpose: Development of a new generation tool materials on the basis of M2 high speed-steel or 41Cr4 steel covered with the carbides. Application of pressureless forming of powder as a manufacturing method of anti-wear coatings gives the possibility to produce this materials with relative low cost of production.Design/methodology/approach: Powder metallurgy, pressureless forming of powder, sintering, microstructure examination, X-ray dispersive energy examination, hardness examination.Finding...

  11. Optimization of casting conditions for heat and abrasion resistant large grey iron castings

    Directory of Open Access Journals (Sweden)

    C. C. Lee

    2007-05-01

    Full Text Available Numerical simulation technology was applied for optimizing the casting design and conditions in large cast iron castings for marine engine. By the simulation of mold filling and solidification sequences the problems of the previous casting conditions were analyzed and marked improvements for large cylinder liner parts were derived from these results. Especially the amount and positions of chills were optimized to increase the mechanical properties and to minimize the shrinkage and microporosity in the castings. Ultrasonic testing, penetration testing and mechanical property testing were carried out for the parts with the modified casting conditions. It showed that no defects in the castings were found and the productivity could be distinctly increased.The mechanical properties satisfied also the specification demanded.

  12. A Novel Approach to Highly Damage Tolerant and Abrasion Resistant EVA Gloves Project

    Data.gov (United States)

    National Aeronautics and Space Administration — As part of the spacesuit pressure garment, the EVA glove incorporates a silicone pad on the palm for protection of the bladder from cuts and punctures. Repeated...

  13. Effects of neoprene mat on diarrhea, mortality and foreleg abrasion of pre-weaning piglets.

    Science.gov (United States)

    Gu, Zhaobing; Xin, Hongwei; Wang, Chaoyuan; Shi, Zhengxiang; Liu, Zuohua; Yang, Feiyun; Lin, Baozhong; Wang, Chao; Li, Baoming

    2010-06-01

    Modern commercial swine farrowing crates are typically equipped with slatted iron floor to improve management efficiency (e.g., ease of manure handling, cleanliness of the farrowing crates and hence improved animal hygiene). However, the bare and hard floor surface can impair the welfare of the sow-litter because of some undesirable impacts on the pigs, such as foreleg abrasion, large temperature gradients between the cold floor surface and the abdomen of the piglets (hence higher susceptibility to diarrhea), and higher pre-weaning mortality or morbidity. Although straw bedding has been shown to be conducive to providing better environment for the sow-litter, use of straw creates challenges in terms of economics, hygiene and manure handling. This study investigates the use of neoprene mat (NM) in key areas of the farrowing crates - underneath the sow and in the piglet suckling area to improve the microenvironment and hence welfare of the sow-litter. Two experiments were conducted, each involving 12 sow-litters. The first experiment was to evaluate the thickness of a rectangular-shaped NM (7, 10 or 13 mm) vs. the slatted iron floor (control or Ctrl) and collect the corresponding animal response data; while the second follow-up experiment was to verify the benefits of supplying an improved, double concave (or H)-shaped NM with 10mm thick (CNM10) vs. Ctrl for the farrowing operation. Results of both experiments demonstrated considerable benefits of the NM placement in the farrowing crates. Specifically, the NM reduced the piglet foreleg lesion area and joint swellings (0% for NM vs. 8-10% for Ctrl during suckling periods in both Expts 1 and 2, Pmortality (18.5+/-5.0%, 6.7+/-3.3% and 9.1+/-5.2% and for Ctrl, NM7 and NM10 and in Expt 1, PExpt 2, PExpt 1, PExpt 2, PExpt 2, P<0.05), indicative of more floor comfort for the NM condition. Results of this study suggest that supply of NM underneath the sow and in the piglet suckling area is conducive to enhancing comfort

  14. A combined CFD-experimental method for abrasive erosion testing of concrete

    Directory of Open Access Journals (Sweden)

    Messa Gianandrea Vittorio

    2018-03-01

    Full Text Available Serious damage may occur to concrete hydraulic structures, such as water galleries, spillways, and stilling basins, due to the abrasive erosion caused by the presence of solid particles in the flow. This underlines the importance of being capable in providing characterization of the concrete from the point of view of its vulnerability to abrasive erosion, in order to improve the design of the structure and the material selection. Nevertheless, the existing apparatus for concrete abrasive erosion testing are either far from allowing realistic simulation of the actual environment in which this phenomenon occurs, or show a large degree of complexity and cost. An alternative method has been developed with the aid of Computational Fluid Dynamics (CFD. CFD was first employed to verify the effectiveness of a new laboratory equipment. Afterwards, a parameter has been introduced which, by successful comparison against preliminary experiments, proved suitable to quantify the effect of the fluid dynamic conditions on the concrete abrasive erosion, thereby opening the way to CFD-based customization of the apparatus. In the future, the synergy of numerical and physical modelling will allow developing predictive models for concrete erosion, making it possible to reliably simulate real structures.

  15. Characterization of abrasion-induced nanoparticle release from paints into liquids and air

    Science.gov (United States)

    Golanski, L.; Gaborieau, A.; Guiot, A.; Uzu, G.; Chatenet, J.; Tardif, F.

    2011-07-01

    Two standard methods for the characterization of the abrasion nanoparticle release into air and liquid from coatings containing nanoparticles were developed. Details of the abrasion processes and the measurement methods are shown. Paints were formulated in an industrial facility. Standard abrasion conditions in wet environments were simulated. The size distribution of the particles abraded into liquid was analyzed by a laser granulometer: submicrometric and micrometric particles were observed, but no nanometric particles. The nanoparticles released in liquid were deposited on filters for SEM (Scanning Electron Microscopy) analysis. No free or agglomerated nanoparticles were observed by SEM: nanoparticles seem to remain embedded in the paint matrix. The same coatings were abraded in the air using another standard method. The ELPI (Electrical Low Pressure Impactor) was used to determine the number size distribution of the dust generated. Abrasion is found to produce submicrometric and micrometric particles in the air but no nanoparticles. Further characterizations by SEM confirmed that no free or agglomerated nanoparticles were emitted: nanoparticles seem to remain embedded in the paint matrix.

  16. Effects of hybrid composition of LCP and glass fibres on abrasive ...

    Indian Academy of Sciences (India)

    Unknown

    Effects of hybrid composition of LCP and glass fibres on abrasive wear of reinforced LLDPE. S A R HASHMI*, AJAY NAIK and NAVIN CHAND. Regional Research Laboratory, Hoshangabad Road, Bhopal 462 026, India. MS received 1 August 2005. Abstract. The hybrid of liquid crystalline polymer (LCP) fibres and glass ...

  17. Spent coffee grounds as air-propelled abrasive grit for weed control

    Science.gov (United States)

    Spent coffee grounds (SCG) represent a significant food waste residue. Value-added uses for this material would be beneficial. Gritty agricultural residues, such as corncob grit, can be employed as abrasive air-propelled agents for organically-compatible postemergence shredding of weed seedlings sel...

  18. Influence of different toothpaste abrasives on the bristle end-rounding quality of toothbrushes.

    Science.gov (United States)

    de Oliveira, G J P L; de Aveiro, J M; Pavone, C; Marcantonio, R A C

    2015-02-01

    To evaluate the influence of different toothpaste abrasives on the bristle wear and bristle tip morphology of toothbrushes with different degrees of hardness. Ninety samples of bovine incisor teeth were used in this study. The samples were randomly divided into three groups according to the bristle hardness of the toothbrush used: soft bristles (S); extra-soft bristles (ES); hard bristles (H). The toothbrushes of each group were randomly divided into six subgroups with five toothbrushes each, according to the abrasive of the toothpaste used in the simulation: Negative control (distilled water); toothpaste 1 (silica); toothpaste 2 (hydrated silica); toothpaste 3 (calcium carbonate, calcium bicarbonate and silica); toothpaste 4 (tetrapotassium pyrophosphate, silica and titanium dioxide); toothpaste 5 (calcium carbonate). The samples were placed in a toothbrushing simulating machine that simulating three months of brushing. The toothbrush bristles were evaluated by the bristle wear index, and the bristle tips morphology was evaluated by the bristle tip morphology index. The ES brush presented the highest bristle wear among the toothbrushes. Additionally, the S brushes showed better morphology of the bristles followed by ES and H brushes. The type of abrasive only influenced the bristle tip morphology of the ES brushes. The toothpaste 3 induced the worse bristle tip morphology than all the other toothpastes. Different abrasives have influence only on the bristle tip morphology of the ES brushes. © 2014 John Wiley & Sons A/S. Published by John Wiley & Sons Ltd.

  19. The effect of dynamic loading on abrasion of mulberry fruit using digital image analysis

    Directory of Open Access Journals (Sweden)

    Fatemeh Afsharnia

    2017-12-01

    Full Text Available The quality of fruits can be reduced due to some damages and impacts which occur during harvesting. One of the most important mechanical damages that can reduce the quality of ripe fruit quality is abrasion damage. This study focused on the effect of dynamic loading based on customary harvesting method on mulberry fruit properties. To this end, different maturity stage and storage regimes were considered. Color quality parameters, firmness, total soluble solid (TSS, total anthocyanins content (TAC and abrasion area were the measured factors. The results revealed that none of the surveyed factors were stable during the experiment. The lightness (L∗, redness (a∗, yellowness (b∗, C∗ value, firmness, TSS and TAC of immature and mature mulberry decreased during storage. The value of a∗, b∗ and C∗ increased as dropping height increased. However, L∗ value, firmness, TSS and TAC of mulberry fruit decreased at both maturity stages (immature and mature mulberry. Moreover, abrasion area increased at immature and mature mulberries by increasing the dropping height and storage time. Keywords: Abrasion, Dynamic loading, Postharvest quality, Mulberry

  20. Abrasive wear based predictive maintenance for systems operating in sandy conditions

    NARCIS (Netherlands)

    Woldman, M.; Tinga, Tiedo; van der Heide, Emile; Masen, Marc Arthur

    2015-01-01

    Machines operating in sandy environments are damaged by the abrasive action of sand particles that enter the machine and become entrapped between components and contacting surfaces. In the case of the military services the combination of a sandy environment and the wide range of tasks to be

  1. IBPAT/OSHA Health and Safety Education Quiz Book. Painters, Abrasive Blasters, Tapers, Paint Makers, Floorcoverers.

    Science.gov (United States)

    International Brotherhood of Painters and Allied Trades, Washington, DC.

    Designed for use by instructors using the "Health and Safety Education Book" (International Brotherhood of Painters and Allied Trades/Occupational Safety and Health Act), this book contains quizzes specifically for painters, abrasive blasters, tapers, paint makers, and floorcoverers. Quizzes included in the book focus on testing areas such as (1)…

  2. Gingival abrasion and recession in manual and oscillating-rotating power brush users

    NARCIS (Netherlands)

    Rosema, N.A.M.; Adam, R.; Grender, J.M.; van der Sluijs, E.; Supranoto, S.C.; van der Weijden, G.A.

    2014-01-01

    Objective To assess gingival recession (GR) in manual and power toothbrush users and evaluate the relationship between GR and gingival abrasion scores (GA). Methods This was an observational (cross-sectional), single-centre, examiner-blind study involving a single-brushing exercise, with 181 young

  3. Toothbrush abrasion, simulated tongue friction and attrition of eroded bovine enamel in vitro

    NARCIS (Netherlands)

    Vieira, A.; Overweg, E.; Ruben, J. L.; Huysmans, M. C. D. N. J. M.

    Objectives: Enamel erosion results in the formation of a softened layer that is susceptible to disruption by mechanical factors such as brushing abrasion, tongue friction and attrition. The aim of this study was to investigate the individual contribution of those mechanical insults to the enamel

  4. Effect of carbon nano tube (CNT) particles in magnetic abrasive finishing of Mg alloy bars

    Energy Technology Data Exchange (ETDEWEB)

    Heng, Lida; Wang, Rui; Kim, Min Soo; Mun, Sang Don; Yang, Gyun Eui [Chonbuk National University, Jeonju (Korea, Republic of)

    2015-11-15

    The Magnetic abrasive finishing (MAF) process is a surface finishing technique in which a magnetic field is used to control abrasive particles during surface finishing of a material. Because smooth surfaces are required for general use, the magnetic abrasive finishing process was developed for finishing surfaces. We studied the effect of CNT particles on the surface roughness of a workpiece. Magnesium alloy bars were used as the cylindrical workpiece and were finished using an MAF process at high workpiece revolution speeds of 1000, 5000, 10000 and 25000 rpm; diamond pastes with diameters of 0.5, 1, and 3 μ were used for comparison. The best value for surface roughness was equivalent to treatment at 0.02 μ m when 0.01 g of CNT particles was mixed together with the unbonded magnetic abrasive at 25000 rpm for 20 seconds. CNT particles were applied to the finishing process to improve the surface roughness of the material, because they have many advantageous properties such as very high strength, light weight, elasticity, and high thermal and air stability. CNT particles are particularly effective for the improvement of Mg alloy bar surface roughness in the MAF process.

  5. NK cells modulate the inflammatory response to corneal epithelial abrasion and thereby support wound healing

    Science.gov (United States)

    Natural killer cells are lymphocytes of the innate immune system that have crucial cytotoxic and regulatory roles in adaptive immunity and inflammation. Herein, we consider a role for these cells in corneal wound healing. After a 2-mm central epithelial abrasion of the mouse cornea, a subset of clas...

  6. Platelet recruitment promotes keratocyte repopulation following corneal epithelial abrasion in the mouse

    Science.gov (United States)

    Corneal abrasion not only damages the epithelium but also induces stromal keratocyte death at the site of injury. While a coordinated cascade of inflammatory cell recruitment facilitates epithelial restoration, it is unclear if this cascade is necessary for keratocyte recovery. Since platelet and ne...

  7. Characterization of abrasion-induced nanoparticle release from paints into liquids and air

    Energy Technology Data Exchange (ETDEWEB)

    Golanski, L; Guiot, A; Uzu, G; Tardif, F [CEA-Grenoble, Liten, 17 rue des Martyrs, F38054 Grenoble Cedex09 (France); Gaborieau, A; Chatenet, J, E-mail: luana.golanski@cea.fr [Blanchon S.A., 28 rue Charles Martin, Saint Fons, 69190 (France)

    2011-07-06

    Two standard methods for the characterization of the abrasion nanoparticle release into air and liquid from coatings containing nanoparticles were developed. Details of the abrasion processes and the measurement methods are shown. Paints were formulated in an industrial facility. Standard abrasion conditions in wet environments were simulated. The size distribution of the particles abraded into liquid was analyzed by a laser granulometer: submicrometric and micrometric particles were observed, but no nanometric particles. The nanoparticles released in liquid were deposited on filters for SEM (Scanning Electron Microscopy) analysis. No free or agglomerated nanoparticles were observed by SEM: nanoparticles seem to remain embedded in the paint matrix. The same coatings were abraded in the air using another standard method. The ELPI (Electrical Low Pressure Impactor) was used to determine the number size distribution of the dust generated. Abrasion is found to produce submicrometric and micrometric particles in the air but no nanoparticles. Further characterizations by SEM confirmed that no free or agglomerated nanoparticles were emitted: nanoparticles seem to remain embedded in the paint matrix.

  8. Apical bud toughness tests and tree sway movements to examine crown abrasion: preliminary results

    Science.gov (United States)

    Tyler Brannon; Wayne Clatterbuck

    2012-01-01

    Apical bud toughness differences were examined for several species to determine if crown abrasion affects shoot growth of determinate and indeterminate species during stand development. Determinate buds will set and harden after initial shoot elongation in the spring, while the indeterminate shoots form leaves from the apical meristem continuously based on the...

  9. Tapered toothbrush filaments in relation to gingival abrasion, removal of plaque and treatment of gingivitis

    NARCIS (Netherlands)

    Versteeg, P.A.; Piscaer, M.; Rosema, N.A.M.; Timmerman, M.F.; van der Velden, U.; van der Weijden, G.A.

    2008-01-01

    Objectives: To compare a tapered filament toothbrush (TFTB) to a control toothbrush (ADA) in their potential to cause gingival abrasion and improve the gingival condition following a period of experimental gingivitis. Methods: Thirty-two subjects refrained from brushing mandibular teeth for 21 days.

  10. Effect of etching and airborne particle abrasion on the microstructure of different dental ceramics.

    Science.gov (United States)

    Borges, Gilberto Antonio; Sophr, Ana Maria; de Goes, Mario Fernando; Sobrinho, Lourenço Correr; Chan, Daniel C N

    2003-05-01

    The ceramic composition and microstructure surface of all-ceramic restorations are important components of an effective bonding substrate. Both hydrofluoric acid etching and airborne aluminum oxide particle abrasion produce irregular surfaces necessary for micromechanical bonding. Although surface treatments of feldspathic and leucite porcelains have been studied previously, the high alumina-containing and lithium disilicate ceramics have not been fully investigated. The purpose of this study was to assess the surface topography of 6 different ceramics after treatment with either hydrofluoric acid etching or airborne aluminum oxide particle abrasion. Five copings each of IPS Empress, IPS Empress 2 (0.8 mm thick), Cergogold (0.7 mm thick), In-Ceram Alumina, In-Ceram Zirconia, and Procera (0.8 mm thick) were fabricated following the manufacturer's instructions. Each coping was longitudinally sectioned into 4 equal parts by a diamond disk. The resulting sections were then randomly divided into 3 groups depending on subsequent surface treatments: Group 1, specimens without additional surface treatments, as received from the laboratory (control); Group 2, specimens treated by use of airborne particle abrasion with 50-microm aluminum oxide; and Group 3, specimens treated with 10% hydrofluoric acid etching (20 seconds for IPS Empress 2; 60 seconds for IPS Empress and Cergogold; and 2 minutes for In-Ceram Alumina, In-Ceram Zirconia, and Procera). Airborne particle abrasion changed the morphologic surface of IPS Empress, IPS Empress 2, and Cergogold ceramics. The surface topography of these ceramics exhibited shallow irregularities not evident in the control group. For Procera, the 50-microm aluminum oxide airborne particle abrasion produced a flattened surface. Airborne particle abrasion of In-Ceram Alumina and In-Ceram Zirconia did not change the morphologic characteristics and the same shallows pits found in the control group remained. For IPS Empress 2, 10% hydrofluoric

  11. Rates of Eolian Rock Abrasion in the Ice-Free Valleys, Antarctica

    Science.gov (United States)

    Hallet, B.; Malin, M. C.; Sletten, R. S.

    2016-12-01

    Eolian abrasion is a principal surface process in dry regions of Earth and Mars and there is evidence for wind processes active on Venus and Titan. Rock abrasion also has practical significance in diverse fields ranging from preservation of cultural material (artifacts, monuments) to damage of solar panels and windshields in arid regions. Despite its scientific and practical importance, and there have ben only few studies that define rates of rock abrasion quantitatively under natural conditions. Herein we report abrasion rates that have been exceptionally well characterized through a unique long-term (30+-year) field experiment in the ice-free McMurdo Dry Valleys, Antarctica. In 1983 and 1984, over 5000 rock targets of several lithologies (25.4 mm-diameter and 5 mm-thick disks of dolerite, basalt, tuff and sandstone) were installed at five heights (7,14, 21, 35, and 70 cm) facing the 4 cardinal directions at 10 locations (one additional site contains fewer targets). Sequential collections of rock targets exposed to abrasion enable definition of mass loss after 1, 5, 10, 30 and 31 years of exposure; the latter were retrieved during the 2014-2015 season. The abrasion rates generally show striking consistency for each lithology at any site; the multiple targets permit definition of intrinsic differences in mass loss. The rates vary considerably from site to site owing to differences in availability of transportable sediment, wind regime, and surface roughness, and at each site, owing to target orientation relative to the dominant winds and, secondarily, to height above the ground. For the hardest targets, basalt and dolerite, mass loss in 30+ years ranged from essentially zero at some sites to 1/3 of the deployed mass (2.59 g; equivalent to a rock thickness >1.8 mm) where abrasion was most active (Site 7, Central Wright Valley). The tuff targets showed the greatest mass loss, and in many cases were entirely abraded away by the end of the experiment.Current work is

  12. Effect of simulated chairside grinding procedures using commercially available abrasive agents on the surface properties of zirconia

    Directory of Open Access Journals (Sweden)

    Ramandeep Sandhu

    2017-01-01

    Clinical Significance: Carbide burs along with copious water irrigation when used to grind zirconia intra-orally produces has a polishing effect, minimal change in hardness & no phase transformation. The present study advocates the use of carbides for chair-side grinding of zirconia.

  13. Studies in vitro of abrasion by different manual toothbrush heads and a standard toothpaste.

    Science.gov (United States)

    Dyer, D; Addy, M; Newcombe, R G

    2000-02-01

    Loss of dentine at the buccal cervical region of teeth has a multifactorial aetiology. However, a considerable amount of circumstantial evidence, supported by laboratory experiments, implicates toothbrushing with toothpaste as a consistent factor. Most interest has centred around the abrasivity of toothpastes, particularly since a toothbrush alone has negligible effects on dentine. The influence of filament stiffness on toothpaste abrasion was the subject of some studies, mostly at least 2 decades ago, and produced conflicting conclusions. Numerous changes to toothbrush design and construction have taken place in recent years. The aim of this study was to measure the abrasion of a standard substrate, acrylic, by a standard toothpaste carried on modern brands of toothbrushes classified by manufacturers as hard (3 brands), medium (3 brands) and soft (6 brands). The substrate was brushed for 20,000 strokes with at least 6 heads from each brand. Measurements of substrate loss were made at 5000 stroke increments by profilometry. Substrate loss for all brushes showed a pattern of abrasion which was to a first approximation linear. Overall, hard brushes caused least abrasion and soft brushes the most, with differences between groups being significant. Within-group differences between brands reached significance for soft and medium brushes but not hard brushes. The results could be explained by increased retention of toothpaste by smaller diameter filaments and denser tufts on soft brushes and the greater flexion of filaments increasing the area of contact with the surface. Calculations on the clinical outcome of these data in vitro indicate that toothbrushing with toothpaste alone would produce minimal damage to dentine even over many years. Differences between brushes therefore are probably of little clinical significance. Certainly, the data do not support the use of hard brushes, particularly in view of the potential detrimental effects to gingival tissues.

  14. The importance of measuring toothpaste abrasivity in both a quantitative and qualitative way.

    Science.gov (United States)

    Johannsen, Gunnar; Tellefsen, Georg; Johannsen, Annsofi; Liljeborg, Anders

    2013-01-01

    To evaluate the relative abrasivity of different toothpastes and polishing pastes both qualitatively and quantitatively. Acrylic plates were exposed to brushing in a brushing machine with a toothpaste/water slurry for 1 and 6 h. Twelve different toothpastes were used and also four different polishing pastes. The results were evaluated using a profilometer after 1 and 6 h of brushing (corresponding to 2000 and 12 000 double strokes, respectively). A surface roughness value (Ra-value) and also a volume loss value were calculated from the profilometer measurements. These values were then correlated to each other. An unpaired t-test for the difference in the abrasion values between the toothpastes and the abrasion values over time was used. The polishing paste RDA® 170 yielded higher Ra-values than RDA 250®, both after 1 and 6 h of brushing (1.01 ± 0.22 and 8.99 ± 1.55 compared to 0.63 ± 0.26 and 7.83 ± 5.89, respectively) as well as volume loss values (3.71 ± 0.17 and 20.20 ± 2.41 compared to 2.15 ± 1.41 and 14.79 ± 11.76, respectively), thus poor correlations between the RDA and Ra and Volume loss values were shown. Among the toothpastes, Apotekets® showed the highest Ra value after 1 h of brushing and Pepsodent® whitening after 6 h of brushing. Pepsodent® whitening also showed the highest volume loss values, both after 1 and 6 h of brushing. This study emphasizes the importance of not only considering the RDA value, but also a roughness value, when describing the abrasivity of a toothpaste. Furthermore, it can be concluded that so called 'whitening' toothpastes do not necessarily have a higher abrasive effect than other toothpastes.

  15. Gingival abrasion and recession in manual and oscillating-rotating power brush users.

    Science.gov (United States)

    Rosema, N A M; Adam, R; Grender, J M; Van der Sluijs, E; Supranoto, S C; Van der Weijden, G A

    2014-11-01

    To assess gingival recession (GR) in manual and power toothbrush users and evaluate the relationship between GR and gingival abrasion scores (GA). This was an observational (cross-sectional), single-centre, examiner-blind study involving a single-brushing exercise, with 181 young adult participants: 90 manual brush users and 91 oscillating-rotating power brush users. Participants were assessed for GR and GA as primary response variables. Secondary response variables were the level of gingival inflammation, plaque score reduction and brushing duration. Pearson correlation was used to describe the relationship between number of recession sites and number of abrasions. Prebrushing (baseline) and post-brushing GA and plaque scores were assessed and differences analysed using paired tests. Two-sample t-test was used to analyse group differences; ancova was used for analyses of post-brushing changes with baseline as covariate. Overall, 97.8% of the study population had at least one site of ≥1 mm of gingival recession. For the manual group, this percentage was 98.9%, and for the power group, this percentage was 96.7% (P = 0.621). Post-brushing, the power group showed a significantly smaller GA increase than the manual group (P = 0.004); however, there was no significant correlation between number of recession sites and number of abrasions for either group (P ≥ 0.327). Little gingival recession was observed in either toothbrush user group; the observed GR levels were comparable. Lower post-brushing gingival abrasion levels were seen in the power group. There was no correlation between gingival abrasion as a result of brushing and the observed gingival recession following use of either toothbrush. © 2014 The Authors International Journal of Dental Hygiene Published by John Wiley & Sons Ltd.

  16. Microstructure and abrasive wear properties of M(Cr,Fe7C3 carbides reinforced high-chromium carbon coating produced by gas tungsten arc welding (GTAW process

    Directory of Open Access Journals (Sweden)

    Soner BUYTOZ

    2010-01-01

    Full Text Available In the present study, high-chromium ferrochromium carbon hypereutectic alloy powder was coated on AISI 4340 steel by the gas tungsten arc welding (GTAW process. The coating layers were analyzed by optical microscopy, X-ray diffraction (XRD, field-emission scanning electron microscopy (FE-SEM, X-ray energy-dispersive spectroscopy (EDS. Depending on the gas tungsten arc welding pa-rameters, either hypoeutectic or hypereutectic microstructures were produced. Wear tests of the coatings were carried out on a pin-on-disc apparatus as function of contact load. Wear rates of the all coating layers were decreased as a function of the loading. The improvement of abrasive wear resistance of the coating layer could be attributed to the high hardness of the hypereutectic M7C3 carbides in the microstruc-ture. As a result, the microstructure of surface layers, hardness and abrasive wear behaviours showed different characteristics due to the gas tungsten arc welding parameters.

  17. Year 2000 commercial issues

    Energy Technology Data Exchange (ETDEWEB)

    Kratz, M.P.J.; Booth, R.T. [Bennett Jones, Calgary, AB (Canada)

    1998-12-31

    This presentation focused on commercial aspects of the Y2K including: (1) special communication issues, (2) outsourcing transactions, (3) joint ventures and the significance for the oil and gas industry, and (4) contingency planning. Communication issues involve interaction with suppliers and vendors of critical systems, liability for Y2K communications (misrepresentation, defamation, promissory estoppel, statutory liability), securities disclosure (Canadian and US SEC requirements), protected communications, protection for Year 2000 statements. Outsourcing problems highlighted include resistance of suppliers to assume responsibility for Y2K problem remediation, factors which support and negate supplier responsibility, scope of suppliers` obligation, and warranties in respect of third party software. Regarding joint ventures, questions concerning limitations on liability, supply warranties, stand-by arrangements, stockpiling inventory, indemnities, confidentiality, operator compensation versus operator risk, and insurance were raised and addressed. Among contingency planning issues the questions of Y2K legal audit, and disclosure aspects of contingency planning were the featured concerns. figs.

  18. Transport behaviour of commercially available 100-Omega standard resistors

    CSIR Research Space (South Africa)

    Schumacher, B

    2001-04-01

    Full Text Available Several types of commercial 100-Omega resistors can be used with the cryogenic current comparator to maintain the resistance unit, derived from the Quantized Hall Effect (QHE), and to disseminate this unit to laboratory resistance standards. Up...

  19. Effect of short-term feeding duration of diets containing commercial whole-cell yeast or yeast subcomponents on immune function and disease resistance in channel catfish, Ictalurus punctatus.

    Science.gov (United States)

    Welker, T L; Lim, C; Yildirim-Aksoy, M; Klesius, P H

    2012-04-01

    Juvenile channel catfish, Ictalurus punctatus, were fed diets supplemented with yeast or yeast subcomponents (YYS) as commercial preparations of β-glucan (MacroGard(®) and Betagard A(®)), mannan oligosaccharide (Bio-Mos(®) Aqua Grade), or whole-cell Saccharomyces cerevisiae (Levucell SB20(®)) at the manufacturers' recommended levels. Fish were fed experimental diets for 1 or 2 weeks prior to disease challenge (pre-challenge feeding periods) and sampled at the end of each feeding period to measure haematological and immune parameters and to determine the effects of dietary YYS on resistance to Edwardsiella ictaluri, the causative agent of enteric septicaemia disease (ESC). Feeding of experimental diets continued for 3 weeks post-challenge. In channel catfish fed diets supplemented with MacroGard(®), Betagard A(®), or Levucell SB20(®), survival in the 1 week pre-challenge feeding group and antibody titres in the 2 week feeding group were significantly higher post-E. ictaluri challenge in relation to catfish fed with the control diet. In fish fed these same three diets, survival to ESC was significantly higher after 1 week vs. 2 weeks feeding, while the antibody response was significantly higher after 2 weeks vs. 1 week. Lysozyme activity was also higher in the 1 week feeding group, but the increased activity was unrelated to diet. Feeding YYS-supplemented diets for a shorter duration of 1 week prior to challenge may prove beneficial in increasing resistance to ESC in channel catfish. However, we cannot discount that feeding YYS diets during the recovery period may have contributed to 'glucan overload' and reduced survival in the 2 week feeding group. Published 2011. This article is a US Government work and is in the public domain in the US.

  20. Study on the abrasion property of the anvil inside a hydraulic DTH hammer fitted with horizontal oriented sliders

    Directory of Open Access Journals (Sweden)

    J. He

    2017-10-01

    Full Text Available Hydraulic hammers have been extensively applied to horizontal directional well drilling in hard rock formations. However, the service life of a hydraulic hammer is still unsatisfactory due to the heavy wear or abrasion of the horizontal anvil, which leads to the failure and the reduction of service life in directional well drilling. In order to improve the performance life of a hydraulic hammer, the new type of anvil with a horizontal oriented slider has been designed. The abrasion property of the horizontal oriented slider have been numerically simulated and analyzed by Finite Element Analysis. Simulation and experimental results have shown that the abrasion rate exponentially varies with the mass of the anvil and the friction coefficient of horizontal oriented slider, nevertheless the abrasion rate of horizontal anvil is almost logarithmically varies with moving velocity of oriented slider. The maximum abrasion rate of horizontal oriented sliders will exceed 4% while moving velocity of the horizontal anvil is larger than 3m/s. While the mass of the anvil is 100kg, the maximum abrasion rate of horizontal oriented slider is 7.5?. However, the maximum abrasion rate of a horizontal oriented slider will be up to 16.5% while the friction coefficient is more than 0.2

  1. Scratch resistance of the ventral skin surface in four snake species (Squamata, Serpentes).

    Science.gov (United States)

    Klein, Marie-Christin G; Gorb, Stanislav N

    2016-04-01

    Snakes are limbless tetrapods highly specialized for sliding locomotion on various substrates. Their skin is constantly exposed to high friction forces, which promotes abrasion. Snake skin has material and surface specializations, presumably optimized for friction and abrasion resistance. We found that different snake species living in different habitats have different abrasion patterns and hypothesized that this correlates with specific epidermal architecture and surface topography. To test this hypothesis artificial scratches, under controlled load conditions, were created on the ventral skin material (epidermis) of four snake species adapted to different habitats: Lampropeltis getula californiae (stony and sandy soil substrates), Epicrates cenchria cenchria (trees, soil and water), Morelia viridis (trees), and Gongylophis colubrinus (burrowing in sand). Abrasion appearance on the skin surface was examined using scanning electron microscopy and white light interferometry. The material failure was different between the species, which we attribute to differences in the epidermis' response to the same abrasive challenge. We also discuss abrasion resistance mechanisms and the correlation with the different ultrastructure and surface microstructure. Copyright © 2016. Published by Elsevier GmbH.

  2. Validation of Proposed Metrics for Two-Body Abrasion Scratch Test Analysis Standards

    Science.gov (United States)

    Street, Kenneth W., Jr.; Kobrick, Ryan L.; Klaus, David M.

    2013-01-01

    Abrasion of mechanical components and fabrics by soil on Earth is typically minimized by the effects of atmosphere and water. Potentially abrasive particles lose sharp and pointed geometrical features through erosion. In environments where such erosion does not exist, such as the vacuum of the Moon, particles retain sharp geometries associated with fracturing of their parent particles by micrometeorite impacts. The relationship between hardness of the abrasive and that of the material being abraded is well understood, such that the abrasive ability of a material can be estimated as a function of the ratio of the hardness of the two interacting materials. Knowing the abrasive nature of an environment (abrasive)/construction material is crucial to designing durable equipment for use in such surroundings. The objective of this work was to evaluate a set of standardized metrics proposed for characterizing a surface that has been scratched from a two-body abrasion test. This is achieved by defining a new abrasion region termed Zone of Interaction (ZOI). The ZOI describes the full surface profile of all peaks and valleys, rather than just measuring a scratch width. The ZOI has been found to be at least twice the size of a standard width measurement; in some cases, considerably greater, indicating that at least half of the disturbed surface area would be neglected without this insight. The ZOI is used to calculate a more robust data set of volume measurements that can be used to computationally reconstruct a resultant profile for de tailed analysis. Documenting additional changes to various surface roughness par ameters also allows key material attributes of importance to ultimate design applications to be quantified, such as depth of penetration and final abraded surface roughness. Further - more, by investigating the use of custom scratch tips for specific needs, the usefulness of having an abrasion metric that can measure the displaced volume in this standardized

  3. Demonstration of Three Corrosion-Resistant Sustainable Roofing Systems

    Science.gov (United States)

    2013-06-01

    UV-resistant acrylic binder (Figure 1). The stone chips provide additional protection from heat and abrasion . The “fawn grey” color that was chosen... peeling , chalking, or any other environmental-related degradation. 3.2.2 Attic environment and roof temperature assessments 3.2.2.1 Stone-coated metal

  4. Effect of Abrasive Waterjet Peening Surface Treatment of Steel Plates on the Strength of Single-Lap Adhesive Joints

    Directory of Open Access Journals (Sweden)

    Kamil Anasiewicz

    2017-09-01

    Full Text Available The paper presents results of comparative study of shear strength of single–lap adhesive joints, depending on the method of surface preparation of steel plates with increased corrosion resistance. The method of preparing adherend surfaces is often one of the most important factors determining the strength of adhesive joints. Appropriate geometric surface development and cleaning of the surface enhances adhesion forces between adherend material and adhesive. One of the methods of shaping engineering materials is waterjet cutting, which in the AWJP – abrasive waterjet peening variant, serves to shape flat surfaces of the material by changing the roughness and introducing stresses into the surface layer. These changes are valuable when preparing adhesive joints. In the study, surface roughness parameters obtained with AWJP treatment, were analyzed in direct relation to the strength of the adhesive joint. As a consequence of the experimental results analysis, the increase in the strength of the adhesive joints was observed in a certain range of parameters used for AWJP treatment. A decrease in shear strength of adhesive joint with the most modified topography of overlap surface was observed.

  5. Bioactivity and laundering resistance of five commercially available, factory-treated permethrin-impregnated fabrics for the prevention of mosquito-borne diseases: the need for a standardized testing and licensing procedure.

    Science.gov (United States)

    Faulde, Michael K; Pages, Frederic; Uedelhoven, Waltraud

    2016-04-01

    Personal protective measures against hematophagous vectors constitute the first line of defense against arthropod-borne diseases. In this regard, a major advance has been the development of residual insecticides that can be impregnated into clothing. Currently, however, information on specific treatment procedures, initial insecticide concentrations, arthropod toxicity, residual activity, and laundering resistance is either fragmentary or non-existent, and no World Health Organization Pesticides Evaluation Scheme or other guidelines exist for the standardized testing and licensing of insecticide-treated clothing. The aim of this study was to analyze the insecticide content, contact toxicity, laundering resistance, and residual activity of five commercially available and commonly used permethrin-treated fabrics-Insect Shield, ExOfficio, Sol's Monarch T-shirts, battle dress uniforms (BDUs), and Labonal socks-against vector-competent Aedes aegypti, Anopheles stephensi, and Culex pipiens mosquitoes under laboratory conditions. Prior to laundering, permethrin concentrations ranged from 4300 to 870 mg/m(2) whereas, after 100 defined machine launderings, the remaining permethrin content fell to between 1800 and 20 mg/m(2), a percentage permethrin loss of 58.1 to 98.5 %. The highest 99 % knockdown (KD99) efficacy of permethrin was detected in Ae. aegypti, followed by An. stephensi and Cx. pipiens demonstrating that Ae. aegypti is the most sensitive species and Cx. pipiens the least sensitive. After 100 launderings, the remaining biocidal efficacy differed markedly among the five brands, with KD99 times varying from 38.8 ± 2.9 to >360 min for Ae. aegypti, from 44 ± 3.5 to >360 min for An. stephensi, and from 98 ± 10.6 to >360 min for Cx. pipiens. Overall, the ranking of the residual biocidal efficacies within the five brands tested was as follows: BDU ≈ Labonal > Sol's Monarch > ExOfficio > Insect Shield. When applying German Armed Forces

  6. Relationship between Los Angeles attrition test and Nordic abrasion test of volcanic rocks

    Science.gov (United States)

    Krutilová, Kateřina; Prikryl, Richard

    2015-04-01

    Various volcanic rocks contribute significantly to the production of crushed stone in the Czech Republic. When used for road surfacing, results of Los Angeles attrition test (LA value below 25 or 30 depending on the mode of use) together with polished stone value are required. In the recent study, we have focused on the search for possible correlation between results obtained by Los Angeles attrition test and Nordic abrasion test, a test widely employed in Scandinavia. For the experimental study, a set of volcanic rocks from 36 active quarries was used. The rocks under study represent range of volcanic rocks from ultrabasic to acid members, formed form Neoproterozoic to Tertiary. The most favourable results of Los Angeles attrition test (i.e. the lowest LA values) were obtained for basalts (range of values 9.4-19.4) and spilites (range of values 8.4-14.9) which are in fact Neoproterozoic to Late Palaeozoic basalts affected by low grade metamorphism. Nordic abrasion test exhibited much broader range of values (6.4 to 36.9) with average value at 15.2 for basalts, resulting in weak coefficient of determination (0.19). . On contrary, narrow range of values from Nordic abrasion test of spilites (7.2-15.9), very similar to the range of LA values, is reflect in higher coefficient of determination (0.56). On contrary, the least favourable properties (LA values 12.3-29.2, Nordic abrasion 16.8-43.3) have been observed for a group of basic to intermediate rocks classified in older literature as melaphyres and diabases (ranging from basalts to trachyndesites and/or trachybasalts) of Palaeozoic age. However, in this specific group of volcanic rocks, the highest coefficient of determination (0.89) between both tests has been achieved. For volcanic rocks exhibiting acid composition (rhyolites and quartz porphyry), coefficient of determination between LA values (15.1-19.3) and Nordic abrasion test (7.3-21.9) is weak (0.42). The weakest relationship between LA values (14

  7. Surface characterization of dental Y-TZP ceramic after air abrasion treatment.

    Science.gov (United States)

    Hallmann, Lubica; Ulmer, Peter; Reusser, Eric; Hämmerle, Christoph H F

    2012-09-01

    The aim of this study was to characterize the surface of Y-TZP after abrasion with various airborne particles. The Y-TZP blanks were cut into 44 discs and sintered according to the manufacturer's instructions. The specimens were treated as follows: (a) control specimens, (b) abraded with 50μm alumina, (c) abraded with 110μm alumina, (d) abraded with 30μm silica-coated alumina, (e) abraded with 110μm silica-coated alumina, (f) abraded with 110μm alumina followed by 110μm silica-coated alumina particles. Airborne abrasion was performed at a pressure of 2.5bar for 15s/cm(2). The Y-TZP was characterized using X-ray photoelectron spectroscopy (XPS), field emission scanning electron microscopy (FESEM) and X-ray diffraction analysis (XRD). Surface morphology of Y-TZP ceramic was changed after the airborne abrasion process compared to the control specimens. The grain boundaries disappeared and part of the airborne particles are embedded and/or rested on the ceramic surfaces. The elemental composition of the Y-TZP surface after the airborne abrasion process depended on the type and size of these particles. The concentration of Si resulted higher after the airborne abrasion process with 110μm alumina followed by 110μm silica-coated alumina particles in comparison to the specimens abraded with 110μm silica-coated alumina particles. The ratio of elements normalized by yttrium for these specimens was: [Zr]/[Y]/[Al]/[Si]=15.2/1.0/26.0/73.6, respectively. The change of grain topography occurred during each impact process. Silica nano-particles covered not only loosely the abraded ceramic surface after abrasion process, but the release of kinetic energy in form of thermal energy resulted in melting of the ceramic surface and in the formation of zirconium silicate. Copyright © 2012 Elsevier Ltd. All rights reserved.

  8. Preparation of Ce-doped colloidal SiO{sub 2} composite abrasives and their chemical mechanical polishing behavior on sapphire substrates

    Energy Technology Data Exchange (ETDEWEB)

    Lei, Hong, E-mail: hong_lei2005@aliyun.com [School of Materials Science and Engineering, Shanghai Institute of Technology, Shanghai 201418 (China); Research Center of Nano-science and Nano-technology, Shanghai University, Shanghai 200444 (China); Tong, Kaiyu; Wang, Zhanyong [School of Materials Science and Engineering, Shanghai Institute of Technology, Shanghai 201418 (China)

    2016-04-01

    Chemical mechanical polishing (CMP) has become a widely accepted global planarization technology. Abrasive is one of key elements during CMP process. In order to enhance removal rate and improve surface quality of sapphire substrate, a series of novel Ce-doped colloidal SiO{sub 2} composite abrasives were prepared by chemical co-precipitation method. The CMP performances of the Ce-doped colloidal SiO{sub 2} composite abrasives on sapphire substrate were investigated by using UNIPOL-1502 polishing equipment. The analyses on the surface of polished sapphire substrate indicate that slurries containing the Ce-doped colloidal SiO{sub 2} composite abrasives exhibit lower surface roughness, higher material removal rate than that of pure colloidal SiO{sub 2} abrasive under the same testing conditions. Furthermore, the acting mechanism of the Ce-doped colloidal silica in sapphire CMP was investigated. X-ray photoelectron spectroscopy analysis shows that solid-state chemical reactions between Ce-doped silica abrasives and sapphire surface occur during CMP process, which can promote the chemical effect in CMP and lead to the improvement of material removing rate. - Highlights: • Novel Ce-doped colloidal SiO{sub 2} composite abrasives were prepared. • The chemical mechanical polishing (CMP) performances of the composite abrasives on sapphire substrate were investigated. • Novel composite abrasives show excellent polishing characteristics comparison with pure colloidal SiO{sub 2} abrasive. • We explore and report the acting mechanism of composite abrasives to sapphire CMP.

  9. Corrosion resistance of Cu-Al coatings produced by thermal spray

    Directory of Open Access Journals (Sweden)

    Laura Marcela Dimaté Castellanos

    2012-01-01

    Full Text Available Many components in the shipbuilding industry are made of copper-based alloys. These pieces tend to break due to corrosion generated by a marine environment; such components can be salvaged through surface engineering, through deposition of suitable coatings. This paper studied the influence of three surface preparation methods involving phosphor bronze substrates concerning the corrosion resistance of commercial coatings having Al-Cu +11% Fe chemical composition. The surface was prepared using three methods: sand blasting, shot blasting and metal polishing with an abrasive disk (with and without a base layer. The deposited coatings were micro-structurally characterised by x-ray diffraction (XRD, optical microscopy and scanning electron microscopy (SEM. Corrosion resistance was evaluated by electrochemical test electrochemical impedance spectroscopy (EIS. Surfaces prepared by sandblasting showed the best resistance to corrosion, so these systems could be a viable alternative for salvaging certain parts in the marine industry. The corrosion mechanisms for the coatings produced are discussed in this research.

  10. Abrasion properties of self-suspended hairy titanium dioxide nanomaterials

    Science.gov (United States)

    Zhang, Jiao-xia; Liu, Si; Yan, Chao; Wang, Xiao-jing; Wang, Lei; Yu, Ya-ming; Li, Shi-yun

    2017-10-01

    Considering the excellent solubility of pyrrolidone ring organic compounds, the synthesized N-(trimethoxysilyl) propyl-N-methyl-2-pyrrolidone chlorides was tethered onto titanium dioxide (TiO2) nanoparticles to improve dispersion of TiO2, and then polyethylene oxide (PEO) oligomer through ion exchange embraced the tethered TiO2 to obtain a novel self-suspended hairy TiO2 nanomaterials without any solvent. A variety of techniques were carried out to illustrate the structure and properties of the self-suspended hairy TiO2 nanomaterials. It was found that TiO2 nanoparticles embody monodispersity in the hybrid system though the "false reunion" phenomenon occurring due to nonpermanent weak physical cross-linking. Remarkably, self-suspended hairy TiO2 nanomaterials exhibit lower viscosity, facilitating maneuverable and outstanding antifriction and wear resistance properties, due to the synergistic lubricating effect between spontaneously forming lubricating film and nano-lubrication of TiO2 cores, overcoming the deficiency of both solid and liquid lubricants. This make them promising candidates for the micro-electromechanic/nano-electromechanic systems (MEMS/NEMS).

  11. Process parameters effect on material removal mechanism and cut quality of abrasive water jet machining

    Directory of Open Access Journals (Sweden)

    Janković P.

    2013-01-01

    Full Text Available The process of the abrasive water jet cutting of materials, supported by the theories of fluid mechanics, abrasive wear and damage mechanics, is a high-tech technologies that provides unique capabilities compared to conventional machining processes. This paper, along the theoretical derivations, provides original contributions in the form of mathematical models of the quantity of the cut surface damage, expressed by the values of cut surface roughness. The particular part of this paper deal with the results of the original experimental research. The research aim was connected with the demands of industry, i.e. the end user. Having in mind that the conventional machining processes are not only lagging behind in terms of quality of cut, or even some requests are not able to meet, but with the advent of composite materials were not able to machine them, because they occurred unacceptable damage (mechanical damage or delamination, fiber pull-out, burning, frayed edges.

  12. [Effect of abrasion on three types of sutures in a metallic anchor].

    Science.gov (United States)

    Acosta Rodríguez, Eduardo; Almazán Díaz, Arturo

    2007-01-01

    It is necessary to slide the suture into the articulation in the arthroscopic techniques, this produce friction and abrasion of the suture, this is the principal cause of failure in the union of anchor-suture. We used a Fastak 2.4 anchor, Sawbones, No 2 Ethibond, No 2 Fiberwire and No 2 Herculine. Each suture was introduce to the anchor eyelet and was cycled in four times with 40N. The angles of traction were 0 degrees and 45 degrees at the same direction of the anchor eyelet and 45 degrees with different direction of the anchor eyelet. Five sutures were used in every test. We performed the Kolmogorov-Smirnof and "t" Student tests. In all the tests there were a significant differences. The strength of the suture is affected by the abrasion in the anchor eyelet.

  13. Correlating field and laboratory rates of particle abrasion, Rio Medio, Sangre de Cristo Mountains, New Mexico

    Science.gov (United States)

    Polito, P. J.; Sklar, L. S.

    2006-12-01

    River bed sediments commonly fine downstream due to a combination of particle abrasion, selective transport of finer grains, and fining of the local sediment supply from hillslopes and tributaries. Particle abrasion rates can be directly measured in the laboratory using tumbling barrels and annular flumes, however, scaling experimental particle abrasion rates to the field has proven difficult due to the confounding effects of selective transport and local supply variations. Here we attempt to correlate laboratory and field rates of particle abrasion in a field setting where these confounding effects can be controlled. The Rio Medio, which flows westward from the crest of the Sangre de Cristo Mountains in north central New Mexico, is one of several streams studied by John P. Miller in the early 1960's. Several kilometers downstream of its headwaters, the river crosses the Picuris-Pecos fault. Upstream of the fault the river receives quartzite, sandstone and shale clasts from the Ortega Formation, while downstream sediments are supplied by the Embudo Granite. Because the upstream lithologies are not resupplied downstream of the fault, any observed fining of these clasts should be due only to abrasion and selective transport. We hypothesize that we can account for the effects of selective transport by comparing relative fining rates for the different upstream lithologies from both the field and a laboratory tumbler. By correlating laboratory abrasion rates with rock strength, we can predict the relative fining rates due solely to abrasion expected in the field; differences between the predicted and observed fining rates could then be attributed to selective transport. We used point counts to measure bed surface sediment grain size distributions at 15 locations along a 25 kilometer reach of the Rio Medio, beginning just downstream of the fault and ending upstream of a developed area with disturbed channel conditions. We recorded intermediate particle diameter as well

  14. Influence of Surface Abrasion on Creep and Shrinkage of Railway Prestressed Concrete Sleepers

    Science.gov (United States)

    Li, Dan; Ngamkhanong, Chayut; Kaewunruen, Sakdirat

    2017-10-01

    Ballasted railway track is very suitable for heavy-rail networks because of its many superior advantages in design, construction, short- and long-term maintenance, sustainability, and life-cycle cost. The sleeper, which supports rail and distributes loads from rail to ballast, is a very important component of rail track system. Prestressed concrete is very popular used in manufacturing sleepers. Therefore, improved knowledge about design techniques for prestressed concrete (PC) sleepers has been developed. However, the ballast angularity causes differential abrasions on the soffit or bottom surface of sleepers. Furthermore, in sharp curves and rapid gradient change, longitudinal and lateral dynamics of rails increase the likelihood of abrasions in concrete sleepers. This paper presents a comparative investigation using a variety of methods to evaluate creep and shrinkage effects in railway prestressed concrete sleepers. The outcome of this study will improve the material design, which is very critical to the durability of railway track components.

  15. Abrasive finishing and polishing in restorative dentistry: a state-of-the-art review.

    Science.gov (United States)

    Jefferies, Steven R

    2007-04-01

    Effective finishing and polishing of dental restorations not only result in optimal aesthetics but also provide for acceptable oral health of soft tissues and marginal integrity of the restorative interface. This review of abrasive technology in dentistry provides an overview of basic principles of abrasive science and considers some research concerning clinically relevant questions. The article also discusses some recent innovations in finishing and polishing devices. This review brings forward some newly published, outcome-based information concerning the relevance and importance of an effective knowledge of finishing and polishing techniques and materials. The overall aim is to provide an enhanced awareness and broader knowledge of the principles and tools available to produce optimal surface finishing and integrity in dental restoratives.

  16. Mathematical model of temperature field distribution in thin plates during polishing with a free abrasive

    Directory of Open Access Journals (Sweden)

    Avilov Alex

    2017-01-01

    Full Text Available The purpose of this paper is to estimate the dynamic characteristics of the heating process of thin plates during polishing with a free abrasive. A mathematical model of the temperature field distribution in space and time according to the plate thickness is based on Lagrange equation of the second kind in the thermodynamics of irreversible processes (variation principle Bio. The research results of thermo elasticity of thin plates (membranes will allow to correct the modes of polishing with a free abrasive to receive the exact reflecting surfaces of satellites reflector, to increase temperature stability and the ability of radio signal reflection, satellite precision guidance. Calculations of temperature fields in thin plates of different thicknesses (membranes is held in the Excel, a graphical characteristics of temperature fields in thin plates (membranes show non-linearity of temperature distribution according to the thickness of thin plates (membranes.

  17. Erosion and abrasion on dental structures undergoing at-home bleaching.

    Science.gov (United States)

    Demarco, Flávio Fernando; Meireles, Sônia Saeger; Sarmento, Hugo Ramalho; Dantas, Raquel Venâncio Fernandes; Botero, Tatiana; Tarquinio, Sandra Beatriz Chaves

    2011-01-01

    This review investigates erosion and abrasion in dental structures undergoing at- home bleaching. Dental erosion is a multifactorial condition that may be idiopathic or caused by a known acid source. Some bleaching agents have a pH lower than the critical level, which can cause changes in the enamel mineral content. Investigations have shown that at-home tooth bleaching with low concentrations of hydrogen or carbamide peroxide have no significant damaging effects on enamel and dentin surface properties. Most studies where erosion was observed were in vitro. Even though the treatment may cause side effects like sensitivity and gingival irritation, these usually disappear at the end of treatment. Considering the literature reviewed, we conclude that tooth bleaching agents based on hydrogen or carbamide peroxide have no clinically significant influence on enamel/dentin mineral loss caused by erosion or abrasion. Furthermore, the treatment is tolerable and safe, and any adverse effects can be easily reversed and controlled.

  18. Brushing abrasion of dentin: effect of diluent and dilution rate of toothpaste.

    Science.gov (United States)

    Turssi, Cecilia P; Messias, Danielle C F; Hara, Anderson Takeo; Hughes, Nathan; Garcia-Godoy, Franklin

    2010-10-01

    To determine whether toothpaste diluent type and dilution rate influence abrasion of dentin. Slabs of human root dentin (4 x 3 x 2 mm) were embedded in epoxy resin, ground and polished. Adhesive tape was placed on the specimen's surface leaving an exposed central area of 1 x 4 mm. Specimens (n = 15) were then brushed for 1,000 strokes in a reciprocal action brushing simulator using toothpaste that had been diluted in a carboxymethylcellulose-based artificial saliva (CMC) or deionized water (DW) from 1:1 to 1:4 (toothpaste:diluents, in weight). Control groups were brushed with undiluted toothpaste, CMC-based saliva or DW only. Brushing simulation was run at 300 g load at 37 degrees C. After brushing, adhesive tape was removed and wear analyzed by optical profilometry. One-way ANOVA (P diluent. Brushing with CMC- or DW-only caused the least abrasion.

  19. Finite element analysis of multi-particle impact on erosion in abrasive water jet machining of titanium alloy

    National Research Council Canada - National Science Library

    Kumar, Naresh; Shukla, Mukul

    2012-01-01

    ...) particle impact on erosion of Grade 5 Titanium alloy (Ti-6Al-4V). The influence of abrasive particle impact angle and velocity on the crater sphericity and depth, and erosion rate has been investigated...

  20. Small-Scale Morphological Features on a Solid Surface Processed by High-Pressure Abrasive Water Jet

    National Research Council Canada - National Science Library

    Can Kang; Haixia Liu

    2013-01-01

    ... with the kinetic energy attached to the abrasive particles involved in the jet stream. Here, experiments were performed, with particular emphasis being placed on the kinetic energy attenuation and turbulent features in the jet stream...

  1. Modeling of the number of stubble stuck elements after abrasive jet machining-processing

    Directory of Open Access Journals (Sweden)

    K. Pietnicki

    2011-07-01

    Full Text Available Sticking of abrasive grains into the surface is the effect of abrasive jet machining processing. For prosthetic works burnt the clay, it may deteriorate the quality of metal-clay connection. Parameters of sandblasting have the significant influence on the amount of stubble elements stuck into the base. The aim of the research is examining possibilities of applying neuron networks for modeling this process. Examples were sandblasted using alternating parameters (pressure of working factor, angle of sandblasting, size of grains. As a next the amount of stubble elements stuck into the base were calculated. Study results allowed to work out a set of 180 standardized teaching patterns. Next, a group of 150 randomly selected neuron networks was submitted to teaching process. The aim was to select net architecture with the highest adjustment for discussed issue. Finally, a MLP (Multi Layer Perception was chosen. Training process of the net involved presentation of process entrance parameters to the net, followed by presentation of researched proportional partaking of stuck elements. In following training cycles the error was decreasing systematically. After finishing the training, the average medium error between the real measurement and the one anticipated by the net was about 5 per cent. Additional number of abrasive jet machining processing was done to verification experiments. As the study shows, designed artificial neuron net stimulates real dependencies appearing during abrasive jet machining-processing in a proper way and can be used for estimating proportional part of grains stuck into base after this processing. It turns out that this phenomenon can be modeled, and its model can be used in a practical way without using mathematical or physical equations.

  2. Investigation of sandwich material surface created by abrasive water jet (AWJ via vibration emission

    Directory of Open Access Journals (Sweden)

    P. Hreha

    2014-01-01

    Full Text Available The paper presents research a of abrasive waterjet cutting of heterogeneous “sandwich“ material with different Young modulus of elasticity of the cutted surface geometry by means of vibration emission. In order to confirm hypothetical assumptions about direct relation between vibration emission and surface quality an experiment in heterogeneous material consisting of stainless steel (DIN 1.4006 / AISI 410 and alloy AlCuMg2 has been provided.

  3. Thoracoscopic parietal pleural argon beam coagulation versus pleural abrasion in the treatment of primary spontaneous pneumothorax.

    Science.gov (United States)

    Bobbio, Antonio; Ampollini, Luca; Internullo, Eveline; Caporale, Domenico; Cattelani, Leonardo; Bettati, Stefano; Carbognani, Paolo; Rusca, Michele

    2006-01-01

    The obliteration of pleural space is useful to prevent recurrences of spontaneous pneumothorax. We retrospectively compared the results of pleural argon beam coagulation versus pleural abrasion in the treatment of primary spontaneous pneumothorax. Between 1996 and 2004, 136 patients underwent surgery for primary spontaneous pneumothorax, with 143 surgical procedures, all performed by VATS. Indications were recurrent pneumothorax in 107 patients, a complicated first episode in 29 and occupational activity in 7. Six patients were excluded because of postoperative histopathological diagnosis other than pulmonary emphysema. In 70 cases pleurodesis was performed with argon beam coagulation and in 67 by Marlex degrees mesh abrasion. These techniques were employed during two different periods. Median follow-up was 68 months in the Marlex degrees group and 41 in the argon group. The two groups resulted as being homogeneous for gender, age, smoking attitude and surgical indication. Statistical analysis was done with chi2 and Fisher's test. No postoperative mortality was observed. Mean recovery time was 5 days. There were three patients with postoperative bleeding who underwent re-operation. There were nine cases of prolonged air-leak, one needing surgical exploration. Nine recurrences were noted, all requiring surgery. Two recurrences were observed in the group treated by pleural abrasion (3.4%) and seven in the group treated by argon coagulation (10.7%). The Fisher's test failed to demonstrate a statistical significance between the two procedures in terms of recurrence rate (p=0.18). Multivariate analysis yielded no risk factors for recurrences. Postoperative complications resulted as being equally distributed in both groups. After primary spontaneous pneumothorax, pleurodesis induced by argon beam parietal pleural coagulation resulted as being no better than that obtained by pleural abrasion in the prevention of recurrences. No benefits in terms of postoperative

  4. Brushing force of manual and sonic toothbrushes affects dental hard tissue abrasion

    OpenAIRE

    Wiegand, Annette; Burkhard, John Patrik Matthias; Eggmann, Florin; Attin, Thomas

    2013-01-01

    OBJECTIVES: This study aimed to determine the brushing forces applied during in vivo toothbrushing with manual and sonic toothbrushes and to analyse the effect of these brushing forces on abrasion of sound and eroded enamel and dentin in vitro. MATERIALS AND METHODS: Brushing forces of a manual and two sonic toothbrushes (low and high frequency mode) were measured in 27 adults before and after instruction of the respective brushing technique and statistically analysed by repeated measures ...

  5. Influence of particle abrasion or hydrofluoric acid etching on lithium disilicate flexural strength.

    Science.gov (United States)

    Menees, Timothy S; Lawson, Nathaniel C; Beck, Preston R; Burgess, John O

    2014-11-01

    Lithium disilicate is a translucent, glass-containing material used for ceramic restorations. Clinicians frequently use alumina abrading or hydrofluoric acid etching to create micromechanical retention in the intaglio surface before bonding a lithium disilicate restoration to the tooth. Few studies have investigated how the etching or abrasion processes affect the flexural strength of lithium disilicate ceramics. The purpose of this study was to measure and compare the flexural strength of e.max CAD after alumina abrasion at differing pressures and acid etching at differing concentrations and times. Bars of e.max CAD (9 groups of 10; 22×2.5×2.5 mm) were prepared, polished sequentially with 180, 320, and 600 abrasive paper, and sintered according to the manufacturer's instructions. Four groups were particle abraded (30-μm alumina particles from 10 mm at 55, 100, 200, or 300 kPa for 10 seconds). Four groups were etched with either 5% hydrofluoric acid (20 seconds or 120 seconds) or 9.5% hydrofluoric acid (20 seconds or 120 seconds). The control was polished and fired only (no treatment). Specimens were placed onto an Instron (1 mm/min crosshead speed) and loaded to failure in a 3-point flexural test. One-way ANOVA and the Dunnett t test determined intergroup differences (α=.05). Compared with the control, the 100, 200, and 300 kPa alumina abraded groups produced significantly lower flexural strengths (P.050); however, the 9.5% hydrofluoric acid at 20 seconds group was nearly statistically significant (P=.051). Alumina particle abrasion at pressures of 100 kPa and higher significantly reduced flexural strength by creating stress risers in e.max CAD and should not be used. Hydrofluoric acid etching should be used to increase micromechanical retention and clean the intaglio surface of the restoration before bonding. Copyright © 2014 Editorial Council for the Journal of Prosthetic Dentistry. Published by Elsevier Inc. All rights reserved.

  6. The importance of measuring toothpaste abrasivity in both a quantitative and qualitative way

    OpenAIRE

    Johannsen, Gunnar; Tellefsen, Georg; Johannsen, Annsofi; Liljeborg, Anders

    2012-01-01

    Objective. To evaluate the relative abrasivity of different toothpastes and polishing pastes both qualitatively and quantitatively. Materials and methods. Acrylic plates were exposed to brushing in a brushing machine with a toothpaste/water slurry for 1 and 6 h. Twelve different toothpastes were used and also four different polishing pastes. The results were evaluated using a profilometer after 1 and 6 h of brushing (corresponding to 2000 and 12 000 double strokes, respectively). A surface ro...

  7. Elimination of intracanal metallic obstructions by abrasion using an operational microscope and ultrasonics.

    Science.gov (United States)

    Nehme, W B

    2001-05-01

    Intracanal metallic obstructions that block any further treatment often prevent the clinician from achieving total cleanliness of the root canal system. For the retrieval of these obstructions, most of the methods described suggest creating and enlarging a space around the obstruction to loosen it before its retrieval. This article describes a technique that consists of mechanical abrasion of the obstruction without altering canal walls by using an operational microscope and ultrasonic spreader.

  8. Performance analysis of cutting graphite-epoxy composite using a 90,000psi abrasive waterjet

    Science.gov (United States)

    Choppali, Aiswarya

    Graphite-epoxy composites are being widely used in many aerospace and structural applications because of their properties: which include lighter weight, higher strength to weight ratio and a greater flexibility in design. However, the inherent anisotropy of these composites makes it difficult to machine them using conventional methods. To overcome the major issues that develop with conventional machining such as fiber pull out, delamination, heat generation and high tooling costs, an effort is herein made to study abrasive waterjet machining of composites. An abrasive waterjet is used to cut 1" thick graphite epoxy composites based on baseline data obtained from the cutting of ¼" thick material. The objective of this project is to study the surface roughness of the cut surface with a focus on demonstrating the benefits of using higher pressures for cutting composites. The effects of major cutting parameters: jet pressure, traverse speed, abrasive feed rate and cutting head size are studied at different levels. Statistical analysis of the experimental data provides an understanding of the effect of the process parameters on surface roughness. Additionally, the effect of these parameters on the taper angle of the cut is studied. The data is analyzed to obtain a set of process parameters that optimize the cutting of 1" thick graphite-epoxy composite. The statistical analysis is used to validate the experimental data. Costs involved in the cutting process are investigated in term of abrasive consumed to better understand and illustrate the practical benefits of using higher pressures. It is demonstrated that, as pressure increased, ultra-high pressure waterjets produced a better surface quality at a faster traverse rate with lower costs.

  9. Effects of different lasers and particle abrasion on surface characteristics of zirconia ceramics.

    Directory of Open Access Journals (Sweden)

    Sakineh Arami

    2014-04-01

    Full Text Available The aim of this study was to assess the surface of yttrium-stabilized tetragonal zirconia (Y-TZP after surface treatment with lasers and airborne-particle abrasion.First, 77 samples of presintered zirconia blocks measuring 10 × 10 × 2 mm were made, sintered and polished. Then, they were randomly divided into 11 groups (n=7 and received surface treatments namely, Er:YAG laser irradiation with output power of 1.5, 2 and 2.5 W, Nd:YAG laser with output power of 1.5, 2 and 2.5 W, CO2 laser with output power of 3, 4 and 5 W, AL2O3 airborne-particle abrasion (50μ and no treatment (controls. Following treatment, the parameters of surface roughness such as Ra, Rku and Rsk were evaluated using a digital profilometer and surface examination was done by SEM.According to ANOVA and Tukey's test, the mean surface roughness (Ra after Nd:YAG laser irradiation at 2 and 2.5 W was significantly higher than other groups. Roughness increased with increasing output power of Nd:YAG and CO2 lasers. Treated surfaces by Er:YAG laser and air abrasion showed similar surface roughness. SEM micrographs showed small microcracks in specimens irradiated with Nd:YAG and CO2 lasers.Nd:YAG laser created a rough surface on the zirconia ceramic with many microcracks; therefore, its use is not recommended. Air abrasion method can be used with Er:YAG laser irradiation for the treatment of zirconia ceramic.

  10. Surface Texture and Optical Properties of Self-Adhering Composite Materials after Toothbrush Abrasion.

    Science.gov (United States)

    Malavasi, Caroline Veiga; Macedo, Elisa Maria; Souza, Karoline da Costa; Rego, Guilherme Ferreira; Schneider, Luis Felipe Jochims; Cavalcante, Larissa Maria

    2015-10-01

    This study evaluated the surface texture and optical properties of two self-adhering composites and a nanofilled composite before and after toothbrush abrasion. Vertise Flow (Kerr), Fusio Liquid (Pentron Clinical) and Filtek Z350 XT (3M ESPE) composites were divided into 3 groups (n = 6). Disks of 12 mm diameter and 2 mm thick were made. All materials were light-cured with a LED light source for 40 seconds. Analyses of surface roughness, gloss retention and color stability were performed 24 hours after light curing and after 20,000 brushing cycles. Data were analyzed with analysis of variance (ANOVA) and Tukey's test (α = 5%). Tukey's test ascertained that toothbrush abrasion resulted in rougher and matte surfaces for all composites tested. Filtek Z350 presented better gloss retention after abrasion. On surface roughness evaluation, there was no statistical difference between Fusio Liquid Dentin and Filtek Z350 resins (p > 0.05). Vertise Flow resin showed better color stability (ΔE), than the other two materials. Nanofilled material presented better gloss retention but it did not produce the best results in aspects related to surface roughness and color stability compared to self-adhering composites. A simulation of degradation process by using toothbrush abrasion produced a rougher and matte surface in all composites tested. The surface texture was not only related to filler's amount present in materials, but also with the organic matrix composition of them. The results suggested that the constant development of new materials, seeking for a technical simplification, seems an innovative attraction for dentist's clinical routine, even though larger studies are necessary to promote to everyone a better understanding and improvement of action and effectiveness of this new class of materials.

  11. Treatment of gingival hyperpigmentation with rotary abrasive, scalpel, and laser techniques: A case series

    OpenAIRE

    Murthy, M Bhanu; Kaur, Jasjit; Das, Rupali

    2012-01-01

    Melanin pigmentation often occurs in the gingiva as a result of an abnormal deposition of melanin, due to which the gums may appear black, but the principles, techniques, and management of the problems associated with gingival melanin pigmentation are still not fully established. Depigmentation procedures such as scalpel surgery, gingivectomy with free gingival autografting, electrosurgery, cryosurgery, chemical agents such as 90% phenol and 95% alcohol, abrasion with diamond bur, Nd: YAG las...

  12. A review of the prediction of textile wear performance with specific reference to abrasion

    CSIR Research Space (South Africa)

    Bird, SL

    1984-08-01

    Full Text Available of degradative agencies which may be classed as biological, chemical or mechanical653-s. Biological wear, mainly confined to natural fibre, is the result of mildew, bacterial or insect attack53J7. The devastation caused to wool by moth lava andcarpet beetle... fabrics. However, to date, a comprehensive reference publication covering various fibre, fabric and abrasion test machine types has not appeared. Many chain stores and retailers, whose reputations rely on claims of high quality, base their standards...

  13. Study of the Effect of Material Machinability on Quality of Surface Created by Abrasive Water Jet

    Czech Academy of Sciences Publication Activity Database

    Klichová, Dagmar; Klich, Jiří

    2016-01-01

    Roč. 149, č. 149 (2016), s. 177-182 E-ISSN 1877-7058. [International Conference on Manufacturing Engineering and Materials, ICMEM 2016. Nový Smokovec, 06.06.2016-10.06.2016] R&D Projects: GA MŠk(CZ) LO1406 Institutional support: RVO:68145535 Keywords : machinability * surface roughness * abrasive waterjet * study of quality * aluminium alloy * optical profilometer Subject RIV: JQ - Machines ; Tools http://www.sciencedirect.com/science/article/pii/S1877705816311614

  14. Surface integrity analysis of abrasive water jet-cut surfaces of friction stir welded joints

    Czech Academy of Sciences Publication Activity Database

    Kumar, R.; Chattopadhyaya, S.; Dixit, A. R.; Bora, B.; Zeleňák, Michal; Foldyna, Josef; Hloch, Sergej; Hlaváček, Petr; Ščučka, Jiří; Klich, Jiří; Sitek, Libor; Vilaca, P.

    2017-01-01

    Roč. 88, č. 5 (2017), s. 1687-1701 ISSN 0268-3768 R&D Projects: GA MŠk(CZ) LO1406; GA MŠk ED2.1.00/03.0082 Institutional support: RVO:68145535 Keywords : friction stir welding (FSW) * abrasive water jet (AWJ) * optical profilometer * topography * surface roughness Subject RIV: JQ - Machines ; Tools Impact factor: 2.209, year: 2016 http://link.springer.com/article/10.1007/s00170-016-8776-0

  15. Turning of wood plastic composites by water jet and abrasive water jet

    Czech Academy of Sciences Publication Activity Database

    Hutyrová, Z.; Ščučka, Jiří; Hloch, Sergej; Hlaváček, Petr; Zeleňák, Michal

    2016-01-01

    Roč. 84, 5-8 (2016), s. 1615-1623 ISSN 0268-3768 R&D Projects: GA MŠk(CZ) LO1406; GA MŠk ED2.1.00/03.0082 Institutional support: RVO:68145535 Keywords : wood plastic composite * water jet * turning * traverse speed * size of abrasive particles Subject RIV: JQ - Machines ; Tools Impact factor: 2.209, year: 2016 http://link.springer.com/article/10.1007/s00170-015-7831-6

  16. On-line monitoring of technological process of material abrasive water jet cutting

    Czech Academy of Sciences Publication Activity Database

    Kinik, D.; Gánovská, B.; Hloch, Sergej; Monka, P.; Monková, K.; Hutyrová, Z.

    2015-01-01

    Roč. 22, č. 2 (2015), s. 351-357 ISSN 1330-3651 R&D Projects: GA MŠk ED2.1.00/03.0082 Institutional support: RVO:68145535 Keywords : abrasive water jet * vibrations * monitoring Subject RIV: JQ - Machines ; Tools Impact factor: 0.464, year: 2015 http://hrcak.srce.hr/index.php?show=clanak&id_clanak_jezik=203519

  17. Turning of wood plastic composites by water jet and abrasive water jet

    Czech Academy of Sciences Publication Activity Database

    Hutyrová, Z.; Ščučka, Jiří; Hloch, Sergej; Hlaváček, Petr; Zeleňák, Michal

    -, September 2015 (2015), s. 1-9 ISSN 0268-3768 R&D Projects: GA MŠk ED2.1.00/03.0082; GA MŠk(CZ) LO1406 Institutional support: RVO:68145535 Keywords : wood plastic composite * water jet * size of abrasive particles * surface quality * traverse speed Subject RIV: JQ - Machines ; Tools Impact factor: 1.568, year: 2015 http://link.springer.com/article/10.1007/s00170-015-7831-6

  18. Experimental Investigations into Abrasive Waterjet Machining of Carbon Fiber Reinforced Plastic

    Directory of Open Access Journals (Sweden)

    Prasad D. Unde

    2015-01-01

    Full Text Available Abrasive waterjet machining (AWJM is an emerging machining process in which the material removal takes place due to abrasion. A stream of abrasive particles mixed with filtered water is subjected to the work surface with high velocity. The present study is focused on the experimental research and evaluation of the abrasive waterjet machining process in order to evaluate the technological factors affecting the machining quality of CFRP laminate using response surface methodology. The standoff distance, feed rate, and jet pressure were found to affect kerf taper, delamination, material removal rate, and surface roughness. The material related parameter, orientation of fiber, has been also found to affect the machining performance. The kerf taper was found to be 0.029 for 45° fiber orientation whereas it was 0.036 and 0.038 for 60° and 90°, respectively. The material removal rate is 18.95 mm3/sec for 45° fiber orientation compared to 18.26 mm3/sec for 60° and 17.4 mm3/sec for 90° fiber orientation. The Ra value for 45° fiber orientation is 4.911 µm and for 60° and 90° fiber orientation it is 4.927 µm and 4.974 µm, respectively. Delamination factor is found to be more for 45° fiber orientation, that is, 2.238, but for 60° and 90° it is 2.029 and 2.196, respectively.

  19. Effect of Phenomena Accompanying Wear in Dry Corundum Abrasive on the Properties and Microstructure of Austempered Ductile Iron with Different Chemical Composition

    Directory of Open Access Journals (Sweden)

    Myszka D.

    2015-04-01

    Full Text Available The research described in this article is a fragment in the series of published works trying to determine the applicability of new materials for parts of the mining machinery. Tests were performed on two groups of austempered ductile iron - one of which contained 1.5% Ni and 0.5% Mo, while the other contained 1.9% Ni and 0.9% Cu. Each group has been heat treated according to the three different heat treatment variants and then the material was subjected to detailed testing of mechanical properties and abrasion wear resistance, measuring also hardness and magnetic properties, and conducting microstructural examinations. The results indicated that each of the tested materials was senstive to the surface hardening effect, which resulted in high wear resistance. It has been found that high temperature of austempering, i.e. 370°C, favours high wear resistance of ductile iron containing nickel and molybdenum. Low temperature of austempering, i.e. 270°C, develops high wear resistance in ductile iron containing nickel and copper. Both these materials offer completely different mechanical properties and as such can be used for different and specific applications.

  20. Adhesion of a self-etching system to dental substrate prepared by Er:YAG laser or air abrasion.

    Science.gov (United States)

    Souza-Zaroni, Wanessa C; Chinelatti, Michelle A; Delfino, Carina S; Pécora, Jesus D; Palma-Dibb, Regina G; Corona, Silmara A M

    2008-08-01

    The purpose of this study was to assess the microtensile bond strength of a self-etching adhesive system to enamel and dentin prepared by Er:YAG laser irradiation or air abrasion, as well as to evaluate the adhesive interfaces by scanning electron microscopy (SEM). For microtensile bond strength test, 80 third molars were randomly assigned to five groups: Group I, carbide bur, control (CB); II, air abrasion with standard tip (ST); III, air abrasion with supersonic tip (SP); IV, Er:YAG laser 250 mJ/4 Hz (L250); V, Er:YAG laser 300 mJ/4 Hz (L300). Each group was divided into two subgroups (n = 8) (enamel, E and dentin, D). E and D surfaces were treated with the self-etching system Adper Prompt L-Pop and composite buildups were done with Filtek Z-250. Sticks with a cross-sectional area of 0.8 mm(2) (+/-0.2 mm(2)) were obtained and the bond strength tests were performed. Data were submitted to ANOVA and Tukey's test. For morphological analysis, disks of 30 third molars were restored, sectioned and prepared for SEM. Dentin presented the highest values of adhesion, differing from enamel. Laser and air-abrasion preparations were similar to enamel. Dentin air-abrasion with standard tip group showed higher bond strength results than Er:YAG-laser groups, however, air-abrasion and Er:YAG laser groups were similar to control group. SEM micrographs revealed that, for both enamel and dentin, the air-abrasion and laser preparations presented irregular adhesive interfaces, different from the ones prepared by rotary instrument. It was concluded that cavity preparations accomplished by both Er:YAG laser energies and air abrasion tips did not positively influence the adhesion to enamel and dentin. (c) 2007 Wiley Periodicals, Inc.

  1. Defining an Abrasion Index for Lunar Surface Systems as a Function of Dust Interaction Modes and Variable Concentration Zones

    Science.gov (United States)

    Kobrick, Ryan L.; Klaus, David M.; Street, Kenneth W., Jr.

    2010-01-01

    Unexpected issues were encountered during the Apollo era of lunar exploration due to detrimental abrasion of materials upon exposure to the fine-grained, irregular shaped dust on the surface of the Moon. For critical design features involving contact with the lunar surface and for astronaut safety concerns, operational concepts and dust tolerance must be considered in the early phases of mission planning. To systematically define material selection criteria, dust interaction can be characterized by two-body or three-body abrasion testing, and subcategorically by physical interactions of compression, rolling, sliding and bending representing specific applications within the system. Two-body abrasion occurs when a single particle or asperity slides across a given surface removing or displacing material. Three-body abrasion occurs when multiple particles interact with a solid surface, or in between two surfaces, allowing the abrasives to freely rotate and interact with the material(s), leading to removal or displacement of mass. Different modes of interaction are described in this paper along with corresponding types of tests that can be utilized to evaluate each configuration. In addition to differential modes of abrasion, variable concentrations of dust in different zones can also be considered for a given system design and operational protocol. These zones include: (1) outside the habitat where extensive dust exposure occurs, (2) in a transitional zone such as an airlock or suitport, and (3) inside the habitat or spacesuit with a low particle count. These zones can be used to help define dust interaction frequencies, and corresponding risks to the systems and/or crew can be addressed by appropriate mitigation strategies. An abrasion index is introduced that includes the level of risk, R, the hardness of the mineralogy, H, the severity of the abrasion mode, S, and the frequency of particle interactions, F.

  2. An abrasion-ablation model description of galactic heavy-ion fragmentation

    Science.gov (United States)

    Townsend, L. W.; Wilson, J. W.; Norbury, J. W.; Bidasaria, H. B.

    1984-01-01

    The fragmentation of high-energy galactic heavy ions by nuclear interactions with arbitrary target nuclei is described within the context of a simple abrasion-ablation fragmentation model. The abrasion part of the theory utilizes a quantum-mechanical formalism based upon an optical model potential approximation to the exact nucleus-nucleus multiple-scattering series. Nuclear charge distributions of the excited prefragments are calculated using either a hypergeometric distribution or a method based upon the zero-point oscillations of the giant dipole resonance. The excitation energy of the prefragment is estimated from the geometric clean-cut abrasion-ablation model. The decay probabilities for the various particle emission channels, in the ablation stage of the fragmentation, are obtained from the EVAP-4 Monte Carlo computer program. Elemental production cross sections for 1.88-GeV/nucleon iron colliding with carbon, silver, and lead targets are calculated and compared with experimental data and with the predictions from the semiempirical relations of Silberberg and Tsao.

  3. Release of particles by abrasion of CNT composites using a belt sander

    Science.gov (United States)

    Matsui, Yasuto; Ishibashi, Tomonori; Nobuyuki, Kato; Nagaya, Taiki; Yoneda, Minoru

    2017-06-01

    There have been many reports on the effect of exposure to nanomaterials such as titanium dioxide, silver, and carbon nanotube (CNT) on human health. Several experiments have examined the abrasion of CNT composites, in which CNT nanoparticles are embedded within a resin or rubber matrix, yielding varying results. Separate study of free CNTs and CNT nanoparticles in relation to health is important due to the different physicochemical characteristics of the two types of material. This study investigated the abrasion of CNT composites using a belt sander inside an enclosed chamber, with variation in the applied load and belt sander speed. At lower speeds, the population of particles with diameters of ~100 nm was observed to increase (cf. mode values of ~10 nm), and we found a relationship between the amount of the raising dust and the abrasion conditions. From these results, we propose a robust and widely applicable method to create particles of nanomaterial-containing composite materials of various types in order to conduct accelerated exposure assessment studies.

  4. Effect of Whitening Toothpastes on Dentin Abrasion: An In Vitro Study.

    Science.gov (United States)

    Vieira, Gustavo Henrique Apolinario; Nogueira, Marcia Bessa; Gaio, Eduardo Jose; Rosing, Cassiano Kuchenbecker; Santiago, Sergio Lima; Rego, Rodrigo Otavio

    To compare the effect of toothbrushing abrasion with hydrated silica-based whitening and regular toothpastes on root dentin using contact profilometry. Ninety dentin specimens (4 x 4 x 2 mm) were randomly divided into five experimental groups (n = 18) according to the toothpaste: three whitening (W1, W2 and W3) and two regular toothpastes (R1 and R2) produced by two different manufacturers. Using a brushing machine, each specimen was brushed with a constant load of 300 g for 2500 cycles (4.5 cycles/s). The toothpastes were diluted at a ratio of 1:3 w/w (dentifrice:distilled water). The brush diamond tip of the profilometer moved at a constant speed of 0.05 mm/s with a force of 0.7 mN. The average value of brushing abrasion in μm (mean ± SD) was obtained from five consecutive measurements of each specimen: W1 = 8.86 ± 1.58, W2 = 7.59 ± 1.04, W3 = 8.27 ± 2.39, R1 = 2.89 ± 1.05 and R2= 2.94 ± 1.29. There was a significant difference between groups (ANOVA, pwhitening and regular toothpastes, but not among the whitening nor among the regular toothpastes. The whitening toothpastes tested can cause more dentin abrasion than the regular ones.

  5. Release of copper-amended particles from micronized copper-pressure-treated wood during mechanical abrasion.

    Science.gov (United States)

    Civardi, Chiara; Schlagenhauf, Lukas; Kaiser, Jean-Pierre; Hirsch, Cordula; Mucchino, Claudio; Wichser, Adrian; Wick, Peter; Schwarze, Francis W M R

    2016-11-28

    We investigated the particles released due to abrasion of wood surfaces pressure-treated with micronized copper azole (MCA) wood preservative and we gathered preliminary data on its in vitro cytotoxicity for lung cells. The data were compared with particles released after abrasion of untreated, water (0% MCA)-pressure-treated, chromated copper (CC)-pressure-treated wood, and varnished wood. Size, morphology, and composition of the released particles were analyzed. Our results indicate that the abrasion of MCA-pressure-treated wood does not cause an additional release of nanoparticles from the unreacted copper (Cu) carbonate nanoparticles from of the MCA formulation. However, a small amount of released Cu was detected in the nanosized fraction of wood dust, which could penetrate the deep lungs. The acute cytotoxicity studies were performed on a human lung epithelial cell line and human macrophages derived from a monocytic cell line. These cell types are likely to encounter the released wood particles after inhalation. Our findings indicate that under the experimental conditions chosen, MCA does not pose a specific additional nano-risk, i.e. there is no additional release of nanoparticles and no specific nano-toxicity for lung epithelial cells and macrophages.

  6. Adhesive interfaces of enamel and dentin prepared by air-abrasion at different distances

    Energy Technology Data Exchange (ETDEWEB)

    Chinelatti, Michelle Alexandra [School of Dentistry of Ribeirao Preto/University of Sao Paulo, Department of Restorative Dentistry, Ribeirao Preto-SP (Brazil)]. E-mail: michinelatti@gmail.com; Andreolli do Amaral, Thais Helena [School of Dentistry of Ribeirao Preto/University of Sao Paulo, Department of Restorative Dentistry, Ribeirao Preto-SP (Brazil); Borsatto, Maria Cristina [School of Dentistry of Ribeirao Preto/University of Sao Paulo, Department of Pediatric Dentistry, Ribeirao Preto-SP (Brazil); Palma-Dibb, Regina Guenka [School of Dentistry of Ribeirao Preto/University of Sao Paulo, Department of Restorative Dentistry, Ribeirao Preto-SP (Brazil); Corona, Silmara Aparecida Milori [School of Dentistry of Ribeirao Preto/University of Sao Paulo, Department of Restorative Dentistry, Ribeirao Preto-SP (Brazil)

    2007-03-30

    The purpose of this study was to analyse, by scanning electron microscopy (SEM), the morphology of enamel and dentin/adhesive interfaces in cavities prepared by air-abrasion at different working distances. Thirty sound third human molars were selected and, on both their buccal and lingual surfaces, class V cavities were prepared by air-abrasion, at 2-, 4-, 6-, 8- and 10-mm working distances, or high-speed bur (control group). After preparation, all cavities were etched with 35% phosphoric acid gel and restored with Single Bond/Filtek Z-250. Buccal and lingual surfaces were separated and restorations sectioned in a buccolingual direction, providing two sections of each cavity, which were analysed by scanning electron microscopy. It was observed that the distances of 6 and 8 mm promoted more homogeneous dentin/adhesive interfaces, with tags formation, and more uniform for enamel, which were similar to the control group. It may be concluded that the air-abrasion working distance can influence the morphology of enamel and dentin/adhesive interfaces, and the intermediate distances provided better adhesive interfaces.

  7. Effect of fluoride gels supplemented with sodium trimetaphosphate on enamel erosion and abrasion: in vitro study.

    Science.gov (United States)

    Pancote, L P; Manarelli, M M; Danelon, M; Delbem, A C B

    2014-03-01

    This in vitro study aims to evaluate the effect of low fluoride (F) gel associate sodium trimetaphosphate (TMP) on erosion with or without abrasion. Enamel blocks (4 mm × 4 mm) selected through surface hardness (SH) is divided into five groups (n=12): gel without F and TMP (placebo), gel containing 4500 ppm F (4500), gel containing 4500 ppm F plus TMP5% (4500 TMP5%), gel containing 9000 ppm F (9000), and gel containing 12,300 ppm F (acid gel). Those groups were additionally subdivided into conditions of erosion (Ero) and of erosion plus abrasion (Ero/Abra). The blocks have undergone a single application of gel on the first day of the study. The erosion challenge was produced by Sprite Zero for five minutes four times a day and abrasion was carried out by machine brushing for 15s. After the challenges, the surface hardness (%SH), wear and cross-sectional hardness (ΔKHN) were analyzed. The data were analyzed using a 2-way ANOVA test followed by a Student-Newman-Keuls (pabrasion. Copyright © 2013 Elsevier Ltd. All rights reserved.

  8. Influence of air abrasion and etching on enamel and adaptation of a dental sealant.

    Science.gov (United States)

    Bevilacqua, L; Cadenaro, M; Sossi, A; Biasotto, M; Di Lenarda, R

    2007-03-01

    Aim of this study was to evaluate the marginal microleakage of a dental sealant using different pre-treatment techniques of the enamel surface. Thirty extracted human intact teeth were selected and divided into 3 groups (n = 10) (1: acid etching with 37% orthophosphoric acid - 3M ESPE, St. Paul, Minnesota, USA; 2: air abrasion; 3: air abrasion + acid etching). The sealant (Helioseal, Vivadent Ivoclar AG, Liechtenstein) was applied into occlusal pits and fissures and light cured for 40 sec. All samples were thermocycled for 500 cycles (5 degrees -55 degrees C). Teeth were then immersed into a 2% methylene blue solution for 24 hrs and sectioned in a mesio-distal direction. Forty-eight sections were obtained for each group. Each section was analysed and photographed with a stereomicroscope (50x) assessing dye penetration (0: no dye penetration; 1: dye penetration restricted to the outer half of the sealant; 2: dye penetration restricted to the inner half of the sealant; 3: dye penetration into the underlying fissure). Data were statistically analysed (Mann-Whitney test). Specimens prepared after air abrasion combined with acid etching showed lower microleakage expression if compared with the other two groups (pabrasion and chemical acid etching represents an effective pre-treatment of enamel surface that may significantly reduce the risk of microleakage.

  9. Evaluation of the effects of enameloplasty and air abrasion on sealant micro-leakage.

    Science.gov (United States)

    Soleymani, Aliasghar; Bahrololoomi, Zahra; Javadinejadi, Shahrzad; Salehi, Parisa

    2014-11-01

    Micro-leakage, one of the major reasons for recurrent decays, may lead to uncontrollable flow of liquids, pulp inflammation and peri-apical pathology. The purpose of this in vitro study was to evaluate micro-leakage of pit and fissure sealants after using three different pit and fissure preparation techniques: 1) acid etching, 2) fissure enameloplasty and acid etching, and 3) air abrasion and acid etching. Sixty-nine extracted sound molars and premolars were randomly divided into three groups (23 samples in each group). Teeth were prepared using one of three occlusal surface treatments. Then the sealant was applied on the occlusal fissures of all teeth. The teeth were thermocycled and stored in normal saline. All teeth were sealed apically and coated with nail varnish and then were immersed in a 2% solution of methylen blue. Two buccolingual sections were made. The surfaces were scored 0 to 3 for the extent of micro-leakage using a stereomicroscope. Data were analyzed by Kruskal- wallis and Dunn procedure. Enameloplasty and acid etching were significantly different regarding micro-leakage (P= 0.016), but no significant difference in micro-leakage was observed between air abrasion and the other methods. Enameloplasty followed by acid etching produced significantly less micro-leakage than the acid etching technique. Air abrasion acid etching was better than the acid etching technique in reducing micro-leakage too.

  10. Evaluation of the effects of enameloplasty and air abrasion on sealant micro-leakage.

    Directory of Open Access Journals (Sweden)

    Aliasghar Soleymani

    2014-12-01

    Full Text Available Micro-leakage, one of the major reasons for recurrent decays, may lead to uncontrollable flow of liquids, pulp inflammation and peri-apical pathology. The purpose of this in vitro study was to evaluate micro-leakage of pit and fissure sealants after using three different pit and fissure preparation techniques: 1 acid etching, 2 fissure enameloplasty and acid etching, and 3 air abrasion and acid etching.Sixty-nine extracted sound molars and premolars were randomly divided into three groups (23 samples in each group. Teeth were prepared using one of three occlusal surface treatments. Then the sealant was applied on the occlusal fissures of all teeth. The teeth were thermocycled and stored in normal saline. All teeth were sealed apically and coated with nail varnish and then were immersed in a 2% solution of methylen blue. Two buccolingual sections were made. The surfaces were scored 0 to 3 for the extent of micro-leakage using a stereomicroscope. Data were analyzed by Kruskal- wallis and Dunn procedure.Enameloplasty and acid etching were significantly different regarding micro-leakage (P= 0.016, but no significant difference in micro-leakage was observed between air abrasion and the other methods.Enameloplasty followed by acid etching produced significantly less micro-leakage than the acid etching technique. Air abrasion acid etching was better than the acid etching technique in reducing micro-leakage too.

  11. Erosion and abrasion on dental structures undergoing at-home bleaching

    Directory of Open Access Journals (Sweden)

    Tarquinio SBC

    2011-07-01

    Full Text Available Flávio Fernando Demarco1, Sônia Saeger Meireles2, Hugo Ramalho Sarmento1, Raquel Venâncio Fernandes Dantas1, Tatiana Botero3, Sandra Beatriz Chaves Tarquinio11Graduate Program in Dentistry, School of Dentistry, Federal University of Pelotas, Brazil; 2Department of Operative Dentistry, Federal University of Paraíba, Brazil; 3Cariology, Restorative Science, and Endodontics Department, School of Dentistry, University of Michigan, MI, USAAbstract: This review investigates erosion and abrasion in dental structures undergoing at-home bleaching. Dental erosion is a multifactorial condition that may be idiopathic or caused by a known acid source. Some bleaching agents have a pH lower than the critical level, which can cause changes in the enamel mineral content. Investigations have shown that at-home tooth bleaching with low concentrations of hydrogen or carbamide peroxide have no significant damaging effects on enamel and dentin surface properties. Most studies where erosion was observed were in vitro. Even though the treatment may cause side effects like sensitivity and gingival irritation, these usually disappear at the end of treatment. Considering the literature reviewed, we conclude that tooth bleaching agents based on hydrogen or carbamide peroxide have no clinically significant influence on enamel/dentin mineral loss caused by erosion or abrasion. Furthermore, the treatment is tolerable and safe, and any adverse effects can be easily reversed and controlled.Keywords: peroxide, tooth bleaching, enamel, dentin, erosion, abrasion

  12. The influence of varnish and high fluoride on erosion and abrasion in a laboratory investigation.

    Science.gov (United States)

    Sar Sancakli, H; Austin, R S; Al-Saqabi, F; Moazzez, R; Bartlett, D

    2015-03-01

    The aim of this study was to investigate the potential of concentrated fluoride varnishes to reduce enamel loss from repeated cycles of citric acid erosion and toothbrush abrasion in vitro. Polished human enamel samples were exposed to fluoride varnishes: Bifluorid10® (NaF&CaF2- 45,200 ppmF), Duraphat® (NaF 22,600 ppmF), Fluor-Protector® (difluorsilane 1000 ppmF) and a control coating of copal ether varnish (0 ppmF) group and a deionized water group. For each group of 16 samples, nine cycles of erosion and nine cycles of erosion-abrasion [1 cycle=erosion (0.3% citric acid, pH 3.2, 5 min)+artificial saliva (1 h, pH 7.0)+abrasion (120 linear strokes in artificial saliva from Oral B medium soft brushes 300 g loading]. The change in the enamel surface was evaluated using optical profilometry. Duraphat® and Bifluorid10® applications had a median (IQR) step height of 4.21 um (1.59) and 5.01 um (1.02). This was statistically significantly less than Fluor-Protector® 6.83 um (1.25), copal ether 7.22 um (1.97) and water 7.39 um (1.96) (pDental Association.

  13. Artificial evolutionary approaches to produce smoother surface in magnetic abrasive finishing of hardened AISI 52100 steel

    Energy Technology Data Exchange (ETDEWEB)

    Teimouri, Reza; Baseri, Hamid [Babol University of Technology, Babol (Iran, Islamic Republic of)

    2013-02-15

    In this work, two models of feed forward back-propagation neural network (FFBP-NN) and adaptive neuro-fuzzy inference system (ANFIS) have been developed to predict the performance of magnetic abrasive finishing process, based on experimental data of literature. Input parameters of process are electromagnet's voltage, mesh number of abrasive particles, poles rotational speed and weight percent of abrasive particles, and also the output is percentage of surface roughness variation. In order to select the best model, a comparison between developed models has been done based on their mean absolute error (MAE) and root mean square error (RMSE). Moreover, optimization methods based on simulated annealing (SA) and particle swarm optimization (PSO) algorithms were used to maximize the percent of surface roughness variation and select the optimal process parameters. Results indicated that the models based on artificial intelligence predict much more precise values with respect to predictive regression model developed in main literature. Also, the ANFIS model had a lowest value of MAE and RMSE with respect to others. So it was used as an objective function to maximize the surface roughness variation by using SA and PSO. Comparison between the obtained optimal solutions and analysis of results in main literature indicated that SA and PSO could find the optimal answers logically and precisely.

  14. Nuclear-chemical methods in a hard tooth tissue abrasion study

    Science.gov (United States)

    Gosman, A.; Spěváček, V.; Koníček, J.; Vopálka, D.; Houŝová, D.; Doležalová, L.

    1999-01-01

    The advanced method consists in implantation—labelling of the thin surface layers of the solid objects, e.g. hard tooth tissue, by atoms of suitable natural or artificial radionuclides. Nuclides from the uranium series were implanted into the surface by using nuclear recoil effect at alpha decay of 226Ra to 222Rn, alpha decay of 222Rn to RaA, alpha decay of RaA to RaB (beta-emitter) and further alpha or beta emitters. With regard to chosen alpha detection and to the half—lives of the radionuclides, there was actually measured the activity of 222Rn, RaA and RaC’ in the thin surface layer. This was followed by the laboratory simulation of the abrasion in the system of “toothbrush—various suspensions of the tooth-pastes—hard tooth tissue (or material standard—ivory)” in specially designed device—the dentoabrasionmeter. The activities of the tissue surface measured before and after abrasion were used for calculations of the relative drop of the surface activity. On this basis the influence of various tooth-pastes containing various abrasive substances was determined.

  15. Experimental evidence that ooid size reflects a dynamic equilibrium between rapid precipitation and abrasion rates

    Science.gov (United States)

    Trower, Elizabeth J.; Lamb, Michael P.; Fischer, Woodward W.

    2017-06-01

    Ooids are enigmatic concentrically coated carbonate sand grains that reflect a fundamental mode of carbonate sedimentation and inorganic product of the carbon cycle-trends in their composition and size are thought to record changes in seawater chemistry over Earth history. Substantial debate persists concerning the roles of physical, chemical, and microbial processes in their growth, including whether carbonate precipitation on ooid surfaces is driven by seawater chemistry or microbial activity, and what role-if any-sediment transport and abrasion play. To test these ideas, we developed an approach to study ooids in the laboratory employing sediment transport stages and seawater chemistry similar to natural environments. Ooid abrasion and precipitation rates in the experiments were four orders of magnitude faster than radiocarbon net growth rates of natural ooids, implying that ooids approach a stable size representing a dynamic equilibrium between precipitation and abrasion. Results demonstrate that the physical environment is as important as seawater chemistry in controlling ooid growth and, more generally, that sediment transport plays a significant role in chemical sedimentary systems.

  16. An in vitro evaluation of the efficiency of an air-abrasion system using helium as a propellant.

    Science.gov (United States)

    Paolinelis, George; Banerjee, Avijit; Watson, Timothy F

    2009-11-01

    Helium is currently used as a propellant gas for air-abrasion with manufacturer claims that this affords greater cutting efficiency compared to the use of air as a propellant. Higher cutting rates, when desired, can reduce operative times. This study set out to investigate these claims by comparing the rate at which helium propelled air-abrasion cut a standard enamel analogue, Macor, versus that of standard air propelled air-abrasion at different propellant pressures. An enamel substitute, Macor, was used as the substrate in order to enable a greater control of physical variables. Powder flow rate, air abrasion nozzle distance and angle to the enamel substitute were constant throughout the experiments. The cutting efficiency of air and helium with propellant pressures of 20, 40, 60, 80 and 100PSI were dynamically investigated, attempting to replicate clinical use. Helium air-abrasion was significantly more efficient in cutting the enamel analogue at all pressures, with a 40% increase for 100PSI propellant pressure. This finding suggests that air-abrasion units using helium as a propellant will be able to cut enamel more quickly in the clinical setting.

  17. Bio-active glass air-abrasion has the potential to remove resin composite restorative material selectively

    Energy Technology Data Exchange (ETDEWEB)

    Milly, Hussam [Biomaterials, Biomimetics and Biophotonics Research Group, Kings College London Dental Institute at Guy' s Hospital, King' s Health Partners, London (United Kingdom); Andiappan, Manoharan [Unit of Dental Public Health, Kings College London Dental Institute at Guy' s Hospital, King' s Health Partners, London (United Kingdom); Thompson, Ian [Biomaterials, Biomimetics and Biophotonics Research Group, Kings College London Dental Institute at Guy' s Hospital, King' s Health Partners, London (United Kingdom); Banerjee, Avijit, E-mail: avijit.banerjee@kcl.ac.uk [Biomaterials, Biomimetics and Biophotonics Research Group, Kings College London Dental Institute at Guy' s Hospital, King' s Health Partners, London (United Kingdom); Unit of Conservative Dentistry, King' s College London Dental Institute at Guy' s Hospital, King' s Health Partners, London (United Kingdom)

    2014-06-01

    The aims of this study were to assess: (a) the chemistry, morphology and bioactivity of bio-active glass (BAG) air-abrasive powder, (b) the effect of three air-abrasion operating parameters: air pressure, powder flow rate (PFR) and the abrasive powder itself, on the selective removal of resin composite and (c) the required “time taken”. BAG abrasive particles were characterised using scanning electron microscopy-energy dispersive X-ray spectrometry (SEM-EDX) and Fourier-transform infrared spectroscopy (FTIR). Standardised resin composite restorations created within an enamel analogue block (Macor™) in vitro, were removed using air-abrasion undersimulated clinical conditions. 90 standardised cavities were scanned before and after resin composite removal using laser profilometry and the volume of the resulting 3D images calculated. Multilevel linear model was used to identify the significant factors affecting Macor™ removal. BAG powder removed resin composite more selectively than conventional air-abrasion alumina powder using the same operating parameters (p < 0.001) and the effect of altering the unit's operating parameters was significant (p < 0.001). In conclusion, BAG powder is more efficient than alumina in the selective removal of resin composite particularly under specific operating parameters, and therefore may be recommended clinically as a method of preserving sound enamel structure when repairing and removing defective resin composite restorations.

  18. Tooth length and incisal wear and growth in guinea pigs (Cavia porcellus) fed diets of different abrasiveness.

    Science.gov (United States)

    Müller, J; Clauss, M; Codron, D; Schulz, E; Hummel, J; Kircher, P; Hatt, J-M

    2015-06-01

    Dental diseases are among the most important reasons for presenting guinea pigs (Cavia porcellus) and other rodents to veterinary clinics, but the aetiopathology of this disease complex is unclear. Clinicians tend to believe that the ever-growing teeth of rabbits and rodents have a constant growth that needs to be worn down by the mastication of an appropriate diet. In this study, we tested the effect of four different pelleted diets of increasing abrasiveness [due to both internal (phytoliths) and external abrasives (sand)] or whole grass hay fed for 2 weeks each in random order to 16 guinea pigs on incisor growth and wear, and tooth length of incisors and cheek teeth. There was a positive correlation between wear and growth of incisors. Tooth lengths depended both on internal and external abrasives, but only upper incisors were additionally affected by the feeding of whole hay. Diet effects were most prominent in anterior cheek teeth, in particular M1 and m1. Cheek tooth angle did not become shallower with decreasing diet abrasiveness, suggesting that a lack of dietary abrasiveness does not cause the typical 'bridge formation' of anterior cheek teeth frequently observed in guinea pigs. The findings suggest that other factors than diet abrasiveness, such as mineral imbalances and in particular hereditary malocclusion, are more likely causes for dental problems observed in this species. Journal of Animal Physiology and Animal Nutrition © 2014 Blackwell Verlag GmbH.

  19. Commercial Buildings Characteristics, 1992

    Energy Technology Data Exchange (ETDEWEB)

    1994-04-29

    Commercial Buildings Characteristics 1992 presents statistics about the number, type, and size of commercial buildings in the United States as well as their energy-related characteristics. These data are collected in the Commercial Buildings Energy Consumption Survey (CBECS), a national survey of buildings in the commercial sector. The 1992 CBECS is the fifth in a series conducted since 1979 by the Energy Information Administration. Approximately 6,600 commercial buildings were surveyed, representing the characteristics and energy consumption of 4.8 million commercial buildings and 67.9 billion square feet of commercial floorspace nationwide. Overall, the amount of commercial floorspace in the United States increased an average of 2.4 percent annually between 1989 and 1992, while the number of commercial buildings increased an average of 2.0 percent annually.

  20. Effect of Bioactive Glass air Abrasion on Shear Bond Strength of Two Adhesive Resins to Decalcified Enamel.

    Directory of Open Access Journals (Sweden)

    Alireza Eshghi

    2014-12-01

    Full Text Available Bioactive glass air abrasion is a conservative technique to remove initial decalcified tissue and caries. This study examined the shear bond strength of composite resin to sound and decalcified enamel air-abraded by bioactive glass (BAG or alumina using etch-and-rinse and self-etch adhesives.Forty-eight permanent molars were root-amputated and sectioned mesiodistally. The obtained 96 specimens were mounted in acrylic resin; the buccal and lingual surfaces remained exposed. A demineralizing solution was used to decalcify half the specimens. Both sound and decalcified specimens were divided into two groups of alumina and bioactive glass air abrasion. In each group, the specimens were subdivided into two subgroups of Clearfil SE Bond or OptiBond FL adhesives (n=12. Composite resin cylinders were bonded on enamel surfaces cured and underwent thermocycling. The specimens were tested for shear bond strength. Data were analyzed using SPSS 16.0 and three-way ANOVA (α=0.05. Similar to the experimental groups, the enamel surface of one specimen underwent SEM evaluation.No significant differences were observed in composite resin bond strength subsequent to alumina or bioactive glass air abrasion preparation techniques (P=0.987. There were no statistically significant differences between the bond strength of etch-and-rinse and self-etch adhesive groups (P=1. Also, decalcified or intact enamel groups had no significant difference (P=0.918. However, SEM analysis showed much less enamel irregularities with BAG air abrasion compared to alumina air abrasion.Under the limitations of this study, preparation of both intact and decalcified enamel surfaces with bioactive glass air abrasion results in similar bond strength of composite resin in comparison with alumina air abrasion using etch-&-rinse or self-etch adhesives.

  1. A study of the potentials achieved during mechanical abrasion and the repassivation rate of titanium and Ti6A14V in inorganic buffer solutions and bovine serum

    Energy Technology Data Exchange (ETDEWEB)

    Contu, F. [University of Mississippi Medical Center, Jackson, MS (United States); Elsener, B. [University of Cagliari (Italy). Dept. of Inorganic and Anlaytical Chemistry; Swiss Federal Institute of Technology, Zurich (Switzerland). Institute of Materials Chemistry; Boehni, H. [Swiss Federal Institute of Technology, Zurich (Switzerland). Institute of Materials Chemistry

    2004-11-15

    Titanium alloys in orthopaedic implants are susceptible to mechanical disruption of the passive film (fretting corrosion). To study this effect, open-circuit potential (ocp) measurements before, during and after mechanical disruption of the passive film in a tribo-electrochemical cell on commercial pure titanium, and Ti6Al4V alloy in inorganic buffer solutions in the pH range from 2.0 to 12.0 and calf bovine serum at pH 4.0 and 7.0 are reported. Additionally, the effect of pH, electrolyte and sample composition on the repassivation rate has been investigated. The potentials achieved during the abrasion of Ti6Al4V are the same as those characterizing pure titanium, which indicates that the corrosion current of both materials in the active state is due to the oxidation of titanium. However, commercial pure titanium displays a tendency to repassivate faster than Ti6Al4V in inorganic buffer solutions thanks to the lower critical current density and the higher catalytic activity towards the hydrogen evolution reaction observed on the pure metal in comparison with the alloy. Proteinaceous solutions like bovine serum, significantly slow down the anodic dissolution and the cathodic reactions both on titanium and the alloy. However, the repassivation rate of the Ti6Al4V is not affected by serum, while that of cp titanium significantly decreases both at pH 4.0 and 7.0. (author)

  2. Differential lead component pulling as a possible mechanism of inside-out abrasion and conductor cable externalization.

    Science.gov (United States)

    Lau, Ernest W

    2013-09-01

    Conductor cable externalization with protrusion (CCE*) is highly prevalent among the Riata 8F and ST 7F defibrillation (DF) leads and infrequently present in the QuickSite and the QuickFlex coronary sinus (CS) leads (St. Jude Medical, Sylmar, CA, USA). A model for CCE* based on differential lead component pulling and conjugate extension with reciprocal compression-bending was developed. Extension of a proximal lead body segment by pectoral or cardiac movements causes reciprocal compression-bending of a distal lead body segment mediated by inextensible conductor cables running down a lead body fixed at various points by fibrous adhesions. The "sawing" action of these cables under tension causes inside-out abrasion of insulation leading to CCE*. DF leads from different manufacturers and the QuickFlex and QuickFlex μ CS leads were subjected to simulated differential pulling. Restitution from differential pulling followed three patterns: complete, partial without escalation, and incomplete with escalation. Only the last pattern (only shown by the Riata 8F and ST 7F leads) was associated with an increased risk to CCE*. For CS leads, deformation concentrated on the more flexible segment when the lead body did not have a uniform construction. The Durata, Riata ST Optim, QuickFlex μ, and Quartet leads should be relatively immune to CCE*. The Durata leads are extremely resistant to longitudinal deformation and probably cause mediastinal displacement rather than differential pulling in response to pectoral movements in vivo. Implantation techniques and lead designs can be used to minimize the risk of CCE*. A bench test for CCE* can be constructed. ©2013, The Author. Journal compilation ©2013 Wiley Periodicals, Inc.

  3. On commercial media bias

    OpenAIRE

    Germano, Fabrizio

    2008-01-01

    Within the spokes model of Chen and Riordan (2007) that allows for non-localized competition among arbitrary numbers of media outlets, we quantify the effect of concentration of ownership on quality and bias of media content. A main result shows that too few commercial outlets, or better, too few separate owners of commercial outlets can lead to substantial bias in equilibrium. Increasing the number of outlets (commercial and non-commercial) tends to bring down this bias; but the strongest ef...

  4. Wear Resistance and Mechanical Behaviour of Epoxy/Mollusk Shell Biocomposites developed for Structural Applications

    Directory of Open Access Journals (Sweden)

    I.O. Oladele

    2016-09-01

    Full Text Available Epoxy resin is one of the strongest commercially exploitable thermosetting polymers in the polymer family; however its expensive nature in comparison with other thermosetting polymers such as vinylester and polyester limits its applications as a structural material. Inexpensive fillers on the other hand, especially those derived from agro-industrial wastes are very important in reducing the overall cost of polymer composites and furthermore influential in enhancing some of their engineering properties. In the present study, the wear resistance and mechanical behaviour of epoxy polymer matrix filled with <75 and 75 μm calcined particles of African land snail shells have been comparatively investigated. The wear resistance and the mechanical behaviour of the composites were studied via Taber Abraser and INSTRON universal testing machine. Also, the elemental constituents of the calcined snail shell and the epoxy biocomposites were characterized by X-Ray Fluorescence Spectroscopy and Scanning Electron Microscopy/Energy Dispersion Spectroscopy. From the experimental results, it was observed that, at the highest filler loading, smaller particle size presented a biocomposite with significant enhancement in wear and mechanical properties. However, it was also observed that increase in particle size showed no significant enhancement in the mechanical properties of the biocomposites.

  5. Abrasion and algal fouling of coarse material on the Murman littoral

    Directory of Open Access Journals (Sweden)

    Malavenda S. V.

    2017-03-01

    Full Text Available On the Murmansk coast of the Barents Sea the boulder littoral zone is widely spread mostly covered by Fucus communities. This is one of the most productive benthic communities of the Barents Sea. The studies of intertidal communities have the long history, but the dynamics of intertidal ecosystems due to surf and storms is not clear. The goal of the work is to identify the leading factors that determine the rate of abrasion of coarse material and fouling algae-macrophytes of the intertidal zone of Murman. The study has been conducted in the Zelenetskaya Bay of the Barents Sea on the basis of the biological station of the MMBI KSC RAS. The rate of abrasion has been carried out during 2004–2013, phyto-overgrowing – 2009–2013. In three pilot landfills 12 samples of coarse material have been exposed during the year (from July to next July. The weight change of the sample as well as species composition and biomass of algae of fouling communities have been investigated. The influence of the surf intensity, temperature of water and air has been analyzed (univariate analysis of variance ANOVA has been applied. It has been shown that on the littoral of the Murmansk coast the abrasion of coarse material is determined primarily by the number of storms, so the storm rate has been proposed. It has been revealed that the density of fouling boulders with macroalgae depends primarily on the intensity of the surf and the average gradient of air temperature. The basis for the emerging communities of annual species are green (Acrosiphonia arcta, Blidingia minima, Spongomorpha aeruginosa and brown algae (Pylaiella littoralis, Dictyosiphon chordaria. These algae groups are found everywhere in Fucus communities of the boulder intertidal zone of the Murman coast and probably they are the intermediate stage of fouling the coarse-grained material

  6. Standardization of a Volumetric Displacement Measurement for Two-Body Abrasion Scratch Test Data Analysis

    Science.gov (United States)

    Street, K. W. Jr.; Kobrick, R. L.; Klaus, D. M.

    2011-01-01

    A limitation has been identified in the existing test standards used for making controlled, two-body abrasion scratch measurements based solely on the width of the resultant score on the surface of the material. A new, more robust method is proposed for analyzing a surface scratch that takes into account the full three-dimensional profile of the displaced material. To accomplish this, a set of four volume- displacement metrics was systematically defined by normalizing the overall surface profile to denote statistically the area of relevance, termed the Zone of Interaction. From this baseline, depth of the trough and height of the plowed material are factored into the overall deformation assessment. Proof-of-concept data were collected and analyzed to demonstrate the performance of this proposed methodology. This technique takes advantage of advanced imaging capabilities that allow resolution of the scratched surface to be quantified in greater detail than was previously achievable. When reviewing existing data analysis techniques for conducting two-body abrasive scratch tests, it was found that the ASTM International Standard G 171 specified a generic metric based only on visually determined scratch width as a way to compare abraded materials. A limitation to this method was identified in that the scratch width is based on optical surface measurements, manually defined by approximating the boundaries, but does not consider the three-dimensional volume of material that was displaced. With large, potentially irregular deformations occurring on softer materials, it becomes unclear where to systematically determine the scratch width. Specifically, surface scratches on different samples may look the same from a top view, resulting in an identical scratch width measurement, but may vary in actual penetration depth and/or plowing deformation. Therefore, two different scratch profiles would be measured as having identical abrasion properties, although they differ

  7. Novel in-situ longitudinal model for the study of dentifrices on dental erosion-abrasion.

    Science.gov (United States)

    Hara, Anderson T; Barlow, Ashley P; Eckert, George J; Zero, Domenick T

    2014-04-01

    A novel longitudinal erosion-abrasion in-situ model was proposed. In an exploratory test (phase 1) toothbrushing effect was investigated using a parallel design, whereas in the main study (phases 1 + 2), a crossover design tested the effect of fluoride dentifrice. In phase 1, 16 subjects (n = 5-6 subjects per group) wore partial dentures with enamel specimens for 28 d and adhered to one of the following treatment regimens: regimen A, erosion only; regimen B, erosion + toothbrushing with fluoride-containing dentifrice [1,100 ppm of fluoride as sodium fluoride (NaF)]; and regimen C, erosion + toothbrushing with placebo dentifrice (0 ppm fluoride). Erosion consisted of the exposure of specimens to grapefruit juice. In regimens B and C, toothbrushing was performed with the test dentifrices 5 min after erosion. For the main study a second phase was carried out in which subjects initially treated with regimen B were treated with regimen C, and vice versa (crossover, n = 11), repeating the same experimental protocol. Enamel wear was measured by optical profilometry at baseline and every 7 d thereafter. In the exploratory test (phase 1), no significant differences were observed among regimens at any of the study time-points. In the main study (phases 1 + 2), higher enamel wear was observed for regimen C than for regimen B. A significant trend was observed for the increase of enamel wear over time. Fluoridated dentifrice reduced the development of erosive-abrasive lesions. The proposed longitudinal model provided adequate responses for erosion-abrasion frequency and fluoride effects. © 2013 Eur J Oral Sci.

  8. Simplified Abrasion Test Methodology for Candidate EVA Glove Lay-Ups

    Science.gov (United States)

    Rabel, Emily; Aitchison, Lindsay

    2015-01-01

    During the Apollo Program, space suit outer-layer fabrics were badly abraded after performing just a few extravehicular activities (EVAs). For example, the Apollo 12 commander reported abrasive wear on the boots that penetrated the outer-layer fabric into the thermal protection layers after less than 8 hrs of surface operations. Current plans for the exploration planetary space suits require the space suits to support hundreds of hours of EVA on a lunar or Martian surface, creating a challenge for space suit designers to utilize materials advances made over the last 40 years and improve on the space suit fabrics used in the Apollo Program. Over the past 25 years the NASA Johnson Space Center Crew and Thermal Systems Division has focused on tumble testing as means of simulating wear on the outer layer of the space suit fabric. Most recently, in 2009, testing was performed on 4 different candidate outer layers to gather baseline data for future use in design of planetary space suit outer layers. In support of the High Performance EVA Glove Element of the Next Generation Life Support Project, testing a new configuration was recently attempted in which require 10% of the fabric per replicate of that need in 2009. The smaller fabric samples allowed for reduced per sample cost and flexibility to test small samples from manufacturers without the overhead to have a production run completed. Data collected from this iteration was compared to that taken in 2009 to validate the new test method. In addition the method also evaluated the fabrics and fabric layups used in a prototype thermal micrometeoroid garment (TMG) developed for EVA gloves under the NASA High Performance EVA Glove Project. This paper provides a review of previous abrasion studies on space suit fabrics, details methodologies used for abrasion testing in this particular study, results of the validation study, and results of the TMG testing.

  9. ADVANCED 3D LASER MICROSCOPY FOR MEASUREMENTS AND ANALYSIS OF VITRIFIED BONDED ABRASIVE TOOLS

    Directory of Open Access Journals (Sweden)

    WOJCIECH KAPLONEK

    2012-12-01

    Full Text Available In many applications, when a precise non-contact assessment of an abrasive tools’ surface is required, alternative measurement methods are often used. Their use offers numerous advantages (referential method as they introduce new qualities into routinely realized measurements. Over the past few years there has been a dynamic increase in the interest for using new types of classical confocal microscopy. These new types are often defined as 3D laser microscopy. This paper presents select aspects of one such method’s application – confocal laser scanning microscopy – for diagnostic analysis of abrasive tools. In addition this paper also looks at the basis for operation, the origins and the development of this measurement technique.The experimental part of this paper presents the select results of tests carried out on grinding wheel active surfaces with sintered microcrystalline corundum grains SG™ bound with glass-crystalline bond. The 3D laser measuring microscopes LEXT OLS3100 and LEXT OLS4000 by Olympus were used in the experiments. Analysis of the obtained measurement data was carried out in dedicated OLS 5.0.9 and OLS4100 2.1 programs, supported by specialist TalyMap Platinum 5.0 software. The realized experiments confirmed the possibility of using the offered measurement method. This concerns both the assessment of grinding wheel active surfaces and their defects, as well as the internal structures of the tools (grain-bond connections. The method presented is an interesting alternative to the typical methods used in the diagnostics of abrasive tools.

  10. Influence on the wear resistance of the particle size used in coatings of Alumina

    Science.gov (United States)

    Santos, A.; Guzmán, R.; Ramirez, Z. Y.

    2017-01-01

    In the literature, it is common to find that the size of the particles used in coatings through thermal spraying processes influences the hardness and wear resistance thereof; this project aimed to quantify the importance of this parameter in the adhesive and abrasive wear resistance when aluminium oxide is deposited on a substrate of AISI 1020 steel, through a thermal spraying by flame process. The methodology consisted of: a) morphological characterization of the powder used in the coatings by scanning electron microscopy, b) deposition of coatings, c) testing of adhesive and abrasive wear (ASTM G99-05 Standard test method for wear testing with a pin-on-disk apparatus and ASTM G65-04 Standard test method for measuring abrasion using dry sand/rubber wheel apparatus), and d) statistical analysis to determine the influence of particle size on wear resistance. The average size of the powder used for coatings was 92, 1690, 8990 and 76790nm. The obtained results allow to identify an inversely proportional behaviour between particle size and wear resistance, in both types of wear (adhesive and abrasive) is shown a logarithmic trend indicating an increase in loss mass during the test as the particle size is also increased and therefore a decrease in wear resistance of the coating.

  11. Investigation on standoff distance influence on kerf characteristics in abrasive water jet cutting of composite materials

    Directory of Open Access Journals (Sweden)

    POPAN Ioan Alexandru

    2017-01-01

    Full Text Available The paper presents an experimental study on processing composite materials using abrasive water jet cutting (AWJC process, analysing one of the main process parameter, standoff distance (SOD. Carbon Fibre Reinforced Plastics (CFRP are used in a wide range of industrial applications, like aerospace and automotive. Cutting CFRP using AWJC involves several challenges like high dimensional accuracy and good surface quality. To produce precise parts by using this process must be understand the influence of the process parameters on quality characteristics. On this study was investigated the standoff distance influence on kerf characteristics. The characteristics of the cut surface (kerf geometry, surface roughness and topography were analyzed.

  12. HYDRO-ABRASIVE JET CLEANING TECHNOLOGY OF STEEL SHEETS DESIGNED FOR LASER CUTTING

    Directory of Open Access Journals (Sweden)

    I. V. Kachanov

    2013-01-01

    Full Text Available Investigations executed by the BNTU “Shipbuilding and hydraulics” department have shown that rather efficient implementation of the requirements to the metal sheet surface designed for laser cutting can be achieved by using hydro-abrasive jet cleaning while applying water pump equipment with the range of pressure – 20–40 MPa. Type of working fluid plays a significant role for obtaining surface of the required quality. The conducted experiments have demonstrated that the efficient solution of the assigned problems can be ensured by using a working fluid containing bentonite clay, surface-active agent polyacrylamide, soda ash and the rest water.

  13. CFD model of multiphase flow in the abrasive water jet tool

    OpenAIRE

    Říha, Zdeněk

    2015-01-01

    The possibility of using CFD fluid flow modeling in area of tools with abrasive water jet is described in the paper. The correct function of such tool is based on proper setting of multiphase flow of water, air and solid particles in the inner space of the tool. The multiphase fluid flow numerical simulation can provide information which show relation between the geometry and the flow field. Then, this stable CFD model of multiphase flow creates key to design of the tool able to work wi...

  14. Minimal alterations on the enamel surface by micro-abrasion: in vitro roughness and wear assessments

    OpenAIRE

    Rodrigues, Marcela Charantola; Mondelli, Rafael Francisco Lia; Oliveira, Gabriela Ulian de; Franco, Eduardo Batista; Baseggio, Wagner; Wang, Linda

    2013-01-01

    Objective: To evaluate the in vitro changes on the enamel surface after a micro-abrasion treatment promoted by different products. Material and Methods: Fifty (50) fragments of bovine enamel (15 mm × 5 mm) were randomly assigned to five groups (n=10) according to the product utilized: G1 (control)= silicone polisher (TDV), G2= 37% phosphoric acid (3M/ESPE) + pumice stone (SS White), G3= Micropol (DMC Equipment), G4= Opalustre (Ultradent) and G5= Whiteness RM (FGM Dental Products). Roug...

  15. Silicon ingot casting: Heat exchanger method. Multi-wire slicing: Fixed abrasive slicing technique, phase 3

    Science.gov (United States)

    Schmid, F.; Khattak, C. P.

    1979-01-01

    In the area of ingot casting the proof of concept of heat exchanger method (HEM) was established. It was also established that HEM cast silicon yielded solar cell performance comparable to Czochralski grown material. Solar cells with conversion efficiencies of up to 15% were fabricated. It was shown that square cross-section ingots can be cast. In the area of crystal slicing, it was established that silicon can be sliced efficiently with the fixed abrasive slicing technique approach. This concept was carried forward to 10 cm diameter workpiece.

  16. Interaction between toothbrushes and toothpaste abrasive particles in simulated tooth cleaning

    OpenAIRE

    Lewis, R; Dwyer-Joyce, R.S.; Pickles, M.J.

    2004-01-01

    There are currently many toothbrush designs on the market incorporating different\\ud filament configurations such as filaments at various angles and different lengths and\\ud made from several different materials. In order to understand how the tooth cleaning\\ud process occurs there is a need to investigate in detail how the abrasive particles in a\\ud toothpaste interact with the filaments in a teeth cleaning contact and cause material\\ud removal from a plaque or stain layer.\\ud \\ud \\ud The fo...

  17. Fouling of coarse-clastic sediments with macrophytes depending on the rate of abrasion, Murmansk coast

    Science.gov (United States)

    Malavenda, S. V.; Mitayev, M. V.; Malavenda, S. S.; Gerasimova, M. V.

    2017-05-01

    It is shown for the first time that the hydrodynamics and average daily gradient of air temperature affect the rate of abrasion of the coarse-clastic material on the boulder littoral of the Murmansk coast, as well as the density of its fouling by macroalgae. The proportion and biomass of species-explerents vary depending on the hydrological and meteorological conditions. The annual species-explerents ( Acrosiphonia arcta, Blidingia minima, Spongomorpha aeruginosa, Pylaiella littoralis) are the basis for new phytocenoses. In the fucus phytocenoses of the boulder littoral, these groupings represent the intermediate stage of fouling of the coarse-clastic material.

  18. Methods of data analysis for the micro-scale abrasion test on coated substrates

    DEFF Research Database (Denmark)

    Kusano, Y.; Acker, K. Van; Hutchings, I.M.

    2004-01-01

    available for data analysis in this test and proposes some new approaches. The wear volumes of the coating and the substrate can be described by two parameters chosen from among the inner and outer crater diameters, the coating thickness, and the penetration depth. The inner crater diameter can usually......The micro-scale abrasive wear test is attractive for coated substrates because it is simple, only small samples are required, and the specific wear rates for both coating and substrate kappa(c) and kappa(s) can be determined simultaneously. This paper reviews and critically discusses the methods...

  19. The geomorphic effect of recent storms - Quantifying meso scale abrasion across a shore platform

    Science.gov (United States)

    Cullen, Niamh; Bourke, Mary; Naylor, Larissa

    2017-04-01

    Boulder abrasion trails (BATs) are lineations on the surface of rock platforms formed by the movement of traction-load clasts by waves. They have been observed on a variety of platform lithologies, including limestone, granite and basalt. Despite previous reporting of these features, the abrasion styles and geomorphic work done by boulder transport has not been quantified. We present the first quantitative measurement of shore platform erosion by boulder transport during extreme storms that occurred in the winter of 2015-2016. Following two storm events in 2016 we mapped and measured 33 individual BATs on a sandstone platform on the west coast of Ireland. The total (minimum) abraded surface area was 10m2. The total (minimum) volume of material abraded was 0.2m3. In order to test the efficacy of this process during non-storm conditions we conducted field experiments on the same platform. We identified two sites on the platform that were similar, but differed in their intertidal roughness. We installed an RBR solo wave pressure transducer (PT) at 0m OD at both locations to record wave data. We measured platform roughness, determined as the fractal dimension of the platform profiles at both sites. We deployed an array of boulders of known dimensions and mass, parallel to the shoreline at 0.5m intervals from the PTs. The experiments were conducted 1. during relatively calm conditions and 2. during higher energy conditions. Data was collected for one tidal cycle. Any boulder displacement distance and direction was measured and geomorphic effects were documented. We find that BATs are formed under a range of wave energy conditions. Our observations indicate that along the North Atlantic coastline, BATs can occur at a high frequency, only limited by sediment supply. Our data show that abrasion by boulder transport is a potentially significant geomorphological process acting to abrade platforms under contemporary climate conditions. In addition, our preliminary findings

  20. Effect of different air-abrasion particles on metal-ceramic bond strength

    OpenAIRE

    Külünk, Tolga; Kurt, Murat; Ural, Çağrı; Külünk, Şafak; Baba, Seniha

    2011-01-01

    Background/purpose: Chipping and delaminating of veneering ceramics are critical problems in the fabrication of metal-ceramic restorations. The purpose of this study was to evaluate the effect of different air-abrasion particles on the shear bond strength of a ceramic to nickel-chromium (Ni-Cr) and cobalt-chromium (Co-Cr) alloys. Materials and methods: Forty square specimens (10 mm × 10 mm × 1.5 mm) were cast for each Ni-Cr and Co-Cr alloys. Specimens were divided into four groups for the ...