WorldWideScience

Sample records for combustion residue treatment

  1. Quality of diets with fluidized bed combustion residue treatment: I. Rat trials

    Energy Technology Data Exchange (ETDEWEB)

    Cahill, N.J.; Reid, R.L.; Head, M.K.; Hern, J.L.; Bennett, O.L.

    Feeding trials were conducted with rats (Rattus rattus) to examine effects of soil application, or dietary inclusion, of fluidized bed combustion residue (FBCR) on the composition and quality of foods. Four diets (vegetable protein, egg protein, chicken, chicken + dietary FBCR) prepared with either FBCR or lime (control) treatments, were fed to weanling, female rats in three growth and reproduction trials. Intake, growth rate, and composition of body and organs of rats were measured. Rats in one trial were bred, their litters maintained on dietary treatments, and the offspring rebred. Treatment (FBCR vs. lime) x diet interactions on food composition and animal responses generally were not significant. Treatment had little effect on element composition of diets; mineral concentrations were in normal ranges. Diet treatment with FBCR depressed (P<0.01) food intake and growth of rats in one trial, but not in others, and had no effect (P<0.05) on body water, protein, ether extract, or gross energy composition. Some differences in element concentrations in the carcass and organs of rats and pups resulted from FBCR treatment, but effects were small and inconsistent. Litters from the first reproductive cycle appeared normal, except for animals fed the chicken + dietary FBCR treatment, on which pups showed poor growth and anemia. Offspring from certain diets were rebred and litters showed a high mortality, although this was not associated specifically with FBCR treatment. Results indicated no major detrimental effects on food composition, or growth, tissue element accumulation, and reproduction in the rat relating to use of FBCR as a soil amendment. 20 refs., 9 tabs.

  2. Effect of torrefaction pre-treatment on physical and combustion characteristics of biomass composite briquette from rice husk and banana residue

    Directory of Open Access Journals (Sweden)

    Amira Atan Nor

    2018-01-01

    Full Text Available Biomass is an alternative renewable energy sources that can generates energy almost same as fossil fuel. The depletion sources of fossil fuel had increase the potential use of biomass energy. In Malaysia, rice husk and banana residues are abundantly left and not treated with proper disposal method which later may contribute to environment and health problems. Thus the development of biomass composite briquette made from rice husk and banana residue is one of the potential ways to reduce the problems and hence may contribute the better way to treat the waste by recycling the waste into a form of biomass product. The biomass briquettes are used for thermal applications because it can produce a complete combustion as it has a consistent quality and high burning efficiency. However, the quality of the biomass briquette can be added by application of torrefaction pre-treatment method. Torrefaction is a thermal method that can produce more high quality of the briquette with high calorific value, high fixed carbon content, low volatile matter, and low ash content. This study was conducted to assess the physical and combustion characteristic of the biomass briquette from rice husk and banana residue which was produced through torrefaction process. The biomass briquette, were densified by using hot press machine with temperature of 180°C for about 30 minutes. The briquette produce are 150 μm in particle size with varies in mixing ratio of rice husk to banana residue which are 100:0, 80:20 and 60:40. After the briquetting process, the biomass fuel briquettes have been undergoes parameter testing and the data have been analysed. Result showed the best biomass briquette is developed from torrefied rice husk and banana residue mixed at ratio of 60:40. Moreover, SEM image reveal that torrefaction pre-treatment has shrinkage the fibres size which confirming the thermal stability of the briquette.

  3. Fluidised-bed combustion of gasification residue

    Energy Technology Data Exchange (ETDEWEB)

    Korpela, T.; Kudjoi, A.; Hippinen, I.; Heinolainen, A.; Suominen, M.; Lu Yong [Helsinki Univ. of Technology (Finland). Lab of Energy Economics and Power Plant Engineering

    1996-12-01

    Partial gasification processes have been presented as possibilities for future power production. In the processes, the solid materials removed from a gasifier (i.e. fly ash and bed material) contain unburnt fuel and the fuel conversion is increased by burning this gasification residue either in an atmospheric or a pressurised fluidised-bed. In this project, which is a part of European JOULE 2 EXTENSION research programme, the main research objectives are the behaviour of calcium and sulphur compounds in solids and the emissions of sulphur dioxide and nitrogen oxides (NO{sub x} and N{sub 2}O) in pressurised fluidised-bed combustion of gasification residues. (author)

  4. Radioactivity of combustion residues from coal-fired power stations

    International Nuclear Information System (INIS)

    Vom Berg, W.; Puch, K.H.

    1996-01-01

    Each year in Germany, about 18 mill. t of combustion residues are produced from the combustion of bituminous coal and lignite. They are utilized to a great extent in the construction industry and in mining. During the combustion of coal, the radio-nuclides remain predominantly in the ash. The radionuclide concentration in lignite ash is within the range of that in natural soil. The combustion residues of bituminous coal contain radio-nuclides of a similar order of magnitude as also can occur in natural rock. The utilization of combustion residues in construction materials makes a negligible contribution to radiation exposure through retention in buildings. (orig.) [de

  5. Unburned carbon in combustion residues from mainly solid biofuels

    Energy Technology Data Exchange (ETDEWEB)

    Bjurstroem H; Lind B; Lagerkvist A

    2012-02-15

    Unburned carbon in 21 combustion residues from solid biofuels is investigated using several methods of analysis (a.o. LOI and TOC), as well as micro-Raman spectroscopy. The results are used to discuss the distribution of unburned carbon in the residues from the different combustion plants and its nature (organic or elemental). The consequences of the elemental nature of carbon for environmental properties of the residue are noted

  6. TENORM: Wastewater Treatment Residuals

    Science.gov (United States)

    Water and wastes which have been discharged into municipal sewers are treated at wastewater treatment plants. These may contain trace amounts of both man-made and naturally occurring radionuclides which can accumulate in the treatment plant and residuals.

  7. Methodology for Evaluating Encapsulated Beneficial Uses of Coal Combustion Residuals

    Science.gov (United States)

    The primary purpose of this document is to present an evaluation methodology developed by the EPA for making determinations about environmental releases from encapsulated products containing coal combustion residuals.

  8. Characterization, leachability and valorization through combustion of residual chars from gasification of coals with pine.

    Science.gov (United States)

    Galhetas, Margarida; Lopes, Helena; Freire, Márcia; Abelha, Pedro; Pinto, Filomena; Gulyurtlu, Ibrahim

    2012-04-01

    This paper presents the study of the combustion of char residues produced during co-gasification of coal with pine with the aim of characterizing them for their potential use for energy. These residues are generally rich in carbon with the presence of other elements, with particular concern for heavy metals and pollutant precursors, depending on the original fuel used. The evaluation of environmental toxicity of the char residues was performed through application of different leaching tests (EN12457-2, US EPA-1311 TCLP and EA NEN 7371:2004). The results showed that the residues present quite low toxicity for some of pollutants. However, depending on the fuel used, possible presence of other pollutants may bring environmental risks. The utilization of these char residues for energy was in this study evaluated, by burning them as a first step pre-treatment prior to landfilling. The thermo-gravimetric analysis and ash fusibility studies revealed an adequate thermochemical behavior, without presenting any major operational risks. Fluidized bed combustion was applied to char residues. Above 700°C, very high carbon conversion ratios were obtained and it seemed that the thermal oxidation of char residues was easier than that of the coals. It was found that the char tendency for releasing SO(2) during its oxidation was lower than for the parent coal, while for NO(X) emissions, the trend was observed to increase NO(X) formation. However, for both pollutants the same control techniques might be applied during char combustion, as for coal. Furthermore, the leachability of ashes resulting from the combustion of char residues appeared to be lower than those produced from direct coal combustion. Copyright © 2011 Elsevier Ltd. All rights reserved.

  9. Decrease of noxious emissions in the residual fuel oil combustion; Disminucion de emisiones nocivas en la combustion de aceite combustible residual

    Energy Technology Data Exchange (ETDEWEB)

    Mandoki W, Jorge [Econergia S. de R. L. de C. V. Mexico, D. F. (Mexico)

    1994-12-31

    The residual fuel oil combustion emits noxious substances such as carbonaceous particulate, nitrogen oxides, and sulfur trioxide at unacceptable levels. Water emulsified in the fuel substantially reduces such emissions, achieving besides, in most of the cases, a net saving in the fuel consumption. The beneficial effects are shown in burning the residual fuel oil as a water emulsion, as well as the method to produce an adequate emulsion. The emulsified fuel technology offers a low cost option to reduce air pollution. The fuel oil quality has been declining during the last decades due to: 1. Increase in the production of crude heavy oils, generally with higher content of asphaltens and sulfur. 2. Less availability of vacuum distillation residues due to its conversion into greater value products. 3. More intensive conversion processes such as catalytic cracking, visbreaking, etc. that increase the asphaltenes concentration in the bottoms, causing instability problems. 4. The increase in the vanadium and other metals content as the concentration of asphaltenes increases. The use of emulsified fuel oil provides an efficient and economical method to substantially reduce the noxious emissions to the atmosphere. The emulsion contains water particles in a diameter between 2 and 20 microns, uniformly distributed in the fuel oil, generally in a proportion generally of 5 to 10%; besides, it contains a tensioactive agent to assure a stable emulsion capable of withstanding the shearing forces of the pumping and distribution systems. When the atomized oil drops get into the combustion chamber, the emulsified water flashes into high pressure steam, originating a violent secondary atomization. The effect of this secondary atomization is the rupture of the oil drops of various hundred microns, producing drops of 5 to 15 microns in diameter. Since the necessary time for combustion is an exponential function of the drop diameter, a very substantial improvement in the combustion is

  10. Combining mechanical-biological residual waste treatment plants with the carbonisation-combustion process; Kombination MBA mit dem Schwel-Brenn-Verfahren

    Energy Technology Data Exchange (ETDEWEB)

    Diekmann, J.; Wiehn, G. [Siemens AG Unternehmensbereich KWU, Erlangen (Germany). Bereich Energieerzeugung

    1998-09-01

    The disposal market for household waste is strongly influenced by the legal framework governing it. A further factor that makes it difficult for the authorities responsible for disposal to decide on residual waste disposal by means of thermal or mechanical-biological treatment plants is the downward pressure on disposal prices from inexpensive, underused landfills. This makes it all the more important for a future-oriented waste management to develop a both economically and ecologically optimised waste disposal concept. In this situation there is much in favour of adopting a concept consisting of a combination of mechanical, mechanical-biological, and thermal treatment which takes due account of waste disposal concepts at the regional and supraregional scale. [Deutsch] Der Entsorgungsmarkt fuer Siedlungsabfaelle wird stark durch die Entwicklung der rechtlichen Rahmenbedingungen beeinflusst. Hinzu kommt, dass der Entscheidungsprozess der oeffentlichen Entsorgungstraeger zur Restabfallentsorgung mittels thermischer oder mechanisch-biologischer Anlagen durch den Druck auf die Entsorgungspreise aufgrund der kostenguenstigen, nicht ausgelasteten Deponien erschwert wird. Umso mehr muss das Ziel einer zukunftsorientierten Abfallwirtschaft sein, unter oekonomischen und oekologischen Gesichtspunkten ein optimiertes Abfallkonzept aufzubauen. Hier kann es sehr hilfreich sein, sich eines Konzeptes, bestehend aus der Kombination von mechanischer, mechanisch-biologischer und thermischer Behandlung unter Beruecksichtigung des regionalen und ueberregionalen Abfallkonzeptes zu bedienen. (orig./SR)

  11. Washing of Rocky Flats Combustible Residues (Conducted March - May 1995)

    Energy Technology Data Exchange (ETDEWEB)

    Mary E. Barr; Ann R. Schake; David A. Romero; Gordon D. Jarvinen

    1999-03-01

    The scope of this project is to determine the feasibility of washing plutonium-containing combustible residues using ultrasonic disruption as a method for dislodging particulate. Removal of plutonium particulate and, to a lesser extent, solubilized plutonium from the organic substrate should substantially reduce potential fire, explosion or radioactive release hazards due to radiolytic hydrogen generation or high flammability. Tests were conducted on polypropylene filters which were used as pre-filters in the rich-residue ion-exchange process at the Los Alamos Plutonium Facility. These filters are similar to the Ful-Flo{reg_sign} cartridges used at Rocky Flats that make up a substantial fraction of the combustible residues with the highest hazard rating. Batch experiments were run on crushed filter material in order to determine the amount of Pu removed by stirring, stirring and sonication, and stirring and sonication with the introduction of Pu-chelating water-soluble polymers or surfactants. Significantly more Pu is removed using sonication and sonication with chelators than is removed with mechanical stirring alone.

  12. Disposal of residue from sifting of combustible waste; Avsaettning av siktrest fraan foerbehandling av braennbart avfall

    Energy Technology Data Exchange (ETDEWEB)

    Niklasson, Fredrik

    2012-11-01

    In waste to energy plants, unwanted species in the fuel may cause corrosion, deposits, agglomeration in the fuel bed, and emissions of pollutants. Countermeasures to such problems are often costly. For at least some of the waste, the fuel properties can be improved by introducing a pretreatment system in which the fine fraction is separated from the waste by sifting. This method has been studied in an earlier Waste Refinery project, WR-06. That study pointed at advantages in performance of the boiler plant and a rough economical analysis indicated substantial benefits. The drawback of the pretreatment was that the residue (the fine fraction) showed as high content of total organic carbon (TOC) as 37 %, by weight. Such a waste fraction is not allowed to be landfilled in Sweden. High TOC content is also a limiting factor for usage as a secondary construction material. To become an applicable pretreatment method, it is necessary to find an appropriate disposal method for the residue material. Present work investigates different possibilities to handle the sifting residue, assuming it has the same properties as in previous study. The residue from sifting needs further treatment, preferably with energy recovery. There are some alternatives, such as combustion, gasification, anaerobic or aerobic digestion. To reduce problems associated by combustion, the waste may be burnt in another more suitable furnace. An alternative is gasification, but that treatment method is not yet an established process for waste fuels. Another option is treatment by anaerobic or aerobic digestion. The high concentrations of metals, however, limit the use of the biologically treated waste to landfilling sites, where it may be utilized as a construction material. The high metal concentrations in the sifting residue imply that it must be kept separate from other biodegradable wastes which are used to produce fertilizers. Thus, this treatment alternative will likely require substantial new

  13. Treatment of alpha-bearing combustible wastes using acid digestion

    International Nuclear Information System (INIS)

    Lerch, R.E.; Allen, C.R.; Blasewitz, A.G.

    1977-11-01

    Acid digestion has been developed at the Hanford Engineering Development Laboratory (HEDL) in Richland, Washington to reduce the volume of combustible nuclear waste materials, while converting them to an inert, noncombustible residue. A 100 kg/day test unit has recently been constructed to demonstrate the process using radioactively contaminated combustible wastes. The unit, called the Radioactive Acid Digestion Test Unit (RADTU) was completed in September 1977 and is currently undergoing cold shakedown tests. Hot operation is expected in May 1978. Features of RADTU include: storage and transfer station for incoming wastes, a feed preparation station, an extrusion feed mechanism for transfer of the waste to the acid digester, the acid digester, a residue recovery system, and an off-gas treatment system

  14. Coal Combustion Residual Beneficial Use Evaluation: Fly Ash Concrete and FGD Gypsum Wallboard

    Science.gov (United States)

    This page contains documents related to the evaluation of coal combustion residual beneficial use of fly ash concrete and FGD gypsum wallboard including the evaluation itself and the accompanying appendices

  15. Calcination/dissolution residue treatment

    International Nuclear Information System (INIS)

    Knight, R.C.; Creed, R.F.; Patello, G.K.; Hollenberg, G.W.; Buehler, M.F.; O'Rourke, S.M.; Visnapuu, A.; McLaughlin, D.F.

    1994-09-01

    Currently, high-level wastes are stored underground in steel-lined tanks at the Hanford site. Current plans call for the chemical pretreatment of these wastes before their immobilization in stable glass waste forms. One candidate pretreatment approach, calcination/dissolution, performs an alkaline fusion of the waste and creates a high-level/low-level partition based on the aqueous solubilities of the components of the product calcine. Literature and laboratory studies were conducted with the goal of finding a residue treatment technology that would decrease the quantity of high-level waste glass required following calcination/dissolution waste processing. Four elements, Fe, Ni, Bi, and U, postulated to be present in the high-level residue fraction were identified as being key to the quantity of high-level glass formed. Laboratory tests of the candidate technologies with simulant high-level residues showed reductive roasting followed by carbonyl volatilization to be successful in removing Fe, Ni, and Bi. Subsequent bench-scale tests on residues from calcination/dissolution processing of genuine Hanford Site tank waste showed Fe was separated with radioelement decontamination factors of 70 to 1,000 times with respect to total alpha activity. Thermodynamic analyses of the calcination of five typical Hanford Site tank waste compositions also were performed. The analyses showed sodium hydroxide to be the sole molten component in the waste calcine and emphasized the requirement for waste blending if fluid calcines are to be achieved. Other calcine phases identified in the thermodynamic analysis indicate the significant thermal reconstitution accomplished in calcination

  16. Management of high sulfur coal combustion residues, issues and practices: Proceedings

    Energy Technology Data Exchange (ETDEWEB)

    Chugh, Y.P.; Beasley, G.A. [eds.

    1994-10-01

    Papers presented at the following sessions are included in this proceedings: (1) overview topic; (2) characterization of coal combustion residues; (3) environmental impacts of residues management; (4) materials handling and utilization, Part I; and (5) materials handling and utilization, Part II. Selected paper have been processed separately for inclusion in the Energy Science and Technology Database.

  17. Major leaching processes of combustion residues - Characterisation, modelling and experimental investigation

    Energy Technology Data Exchange (ETDEWEB)

    Yan Jinying

    1998-12-31

    Characterising leaching behaviour provides ample evidence to identify the major leaching processes of combustion residues. Neutralisation and chemical weathering govern the leaching reactions and control the release of elements from combustion residues, and are thus considered to be the major leaching processes. According to experimental investigations and geochemical simulations, the leaching kinetics of buffering materials are key issues for the understanding of the neutralizing processes. The acid neutralizing capacity at different pH levels depends mainly on the mineralogy of the combustion residues. In combustion residues, the dissolution of glass phases is expected to play an important role in a long-term neutralizing process. The neutralizing process in a flow system is significantly different from that in a batch system. The neutralizing ability of a combustion residue may be strongly affected by solute transport and carbonation reactions in a natural leaching environment. The chemical weathering mainly involves the matrix of combustion residues consisting mostly of glass phases. The dissolution kinetics of waste glass and other possible processes involved in the chemical weathering have been investigated and incorporated into a kinetic reactive transport model. Most important processes in the chemical weathering can be simulated simultaneously using this model. The results show that there is a complicated relationship between the factors controlling the long-term chemical weathering. The environmental impact of the glass dissolution cannot be neglected. Although the glass dissolution provides considerable buffering capacity in long-term weathering, the carbonate is usually a dominant buffering mineral in actual weathering processes. The transformation of carbonate should be considered as an important process in the chemical weathering. The formation of secondary minerals may considerably alter the mineralogy of the waste, and thus change the leaching

  18. Non-combustible solid waste treatment system

    International Nuclear Information System (INIS)

    Takada, Takashi; Kurahashi, Takafumi; Karita, Yoichi

    1995-01-01

    An induction heat melting system which gets a high volume reduction and a stable product in regard to strength, and good containment of radionuclide, is being developed. This system uses the heat from the ceramic canister itself previously placed in the induction heat melting furnace what is called the in-can type ceramic canister. As a results, this melting solidification system is applicable for the treatment of non-combustible solid waste made up of several different types of waste. This paper describes the basic process flow of the induction heat melting system, melting test results using a mock-up plant and radionuclide behavior test results which include radionuclide volatilization rate during the melting and decontamination performance data of the off-gas treatment system using a hot test apparatus. This paper also describes an outline of system, performance of system such as volume reduction ratio and treatment capacity, the safety design and safety measures of system about the non-combustible solid waste treatment system using this induction heat melting system. (author)

  19. Stabilization of Rocky Flats combustible residues contaminated with plutonium metal and organic solvents

    International Nuclear Information System (INIS)

    Bowen, S.M.; Cisneros, M.R.; Jacobson, L.L.; Schroeder, N.C.; Ames, R.L.

    1998-01-01

    This report describes tests on a proposed flowsheet designed to stabilize combustible residues that were generated at the Rocky Flats Environmental Technology Site (RFETS) during the machining of plutonium metal. Combustible residues are essentially laboratory trash contaminated with halogenated organic solvents and plutonium metal. The proposed flowsheet, designed by RFETS, follows a glovebox procedure that includes (1) the sorting and shredding of materials, (2) a low temperature thermal desorption of solvents from the combustible materials, (3) an oxidation of plutonium metal with steam, and (4) packaging of the stabilized residues. The role of Los Alamos National Laboratory (LANL) in this study was to determine parameters for the low temperature thermal desorption and steam oxidation steps. Thermal desorption of carbon tetrachloride (CCl 4 ) was examined using a heated air stream on a Rocky Flats combustible residue surrogate contaminated with CCl 4 . Three types of plutonium metal were oxidized with steam in a LANL glovebox to determine the effectiveness of this procedure for residue stabilization. The results from these LANL experiments are used to recommend parameters for the proposed RFETS stabilization flowsheet

  20. Material and energy recovery from Automotive Shredded Residues (ASR) via sequential gasification and combustion.

    Science.gov (United States)

    Viganò, F; Consonni, S; Grosso, M; Rigamonti, L

    2010-01-01

    Shredding is the common end-of-life treatment in Europe for dismantled car wrecks. It produces the so-called Automotive Shredded Residue (ASR), usually disposed of in landfill. This paper summarizes the outcome of a study carried out by Politecnico di Milano and LEAP with the support of Actelios SpA on the prospects of a technology based on sequential gasification and combustion of this specific waste stream. Its application to the treatment of ASR allows the recovery of large fractions of metals as non-oxidized, easily marketable secondary raw materials, the vitrification of most of the ash content and the production of power via a steam cycle. Results show that despite the unfavourable characteristics of ASR, the proposed technology can reach appealing energy performances. Three of four environmental impact indicators and the cumulative energy demand index are favourable, the main positive contributes being electricity production and metal recovery (mainly aluminium and copper). The only unfavourable indicator is the global warming index because, since most of the carbon in ASR comes from fossil sources, the carbon dioxide emissions at the stack of the thermal treatment plant are mainly non-renewable and, at the same time, the avoided biogas production from the alternative disposal route of landfilling is minor.

  1. Chemical analysis of solid residue from liquid and solid fuel combustion: Method development and validation

    Energy Technology Data Exchange (ETDEWEB)

    Trkmic, M. [University of Zagreb, Faculty of Mechanical Engineering and Naval Architecturek Zagreb (Croatia); Curkovic, L. [University of Zagreb, Faculty of Chemical Engineering and Technology, Zagreb (Croatia); Asperger, D. [HEP-Proizvodnja, Thermal Power Plant Department, Zagreb (Croatia)

    2012-06-15

    This paper deals with the development and validation of methods for identifying the composition of solid residue after liquid and solid fuel combustion in thermal power plant furnaces. The methods were developed for energy dispersive X-ray fluorescence (EDXRF) spectrometer analysis. Due to the fuels used, the different composition and the location of creation of solid residue, it was necessary to develop two methods. The first method is used for identifying solid residue composition after fuel oil combustion (Method 1), while the second method is used for identifying solid residue composition after the combustion of solid fuels, i. e. coal (Method 2). Method calibration was performed on sets of 12 (Method 1) and 6 (Method 2) certified reference materials (CRM). CRMs and analysis test samples were prepared in pellet form using hydraulic press. For the purpose of method validation the linearity, accuracy, precision and specificity were determined, and the measurement uncertainty of methods for each analyte separately was assessed. The methods were applied in the analysis of real furnace residue samples. (Copyright copyright 2012 WILEY-VCH Verlag GmbH and Co. KGaA, Weinheim)

  2. The atomization and the flame structure in the combustion of residual fuel oils; La atomizacion y estructura de flama en la combustion de combustibles residuales

    Energy Technology Data Exchange (ETDEWEB)

    Bolado Estandia, Ramon [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

    1985-12-31

    In this article a research on the combustion of heavy residual fuel oils is presented. The type of flames studied were obtained by means of the burning of sprays produced by an atomizer designed and calibrated specially for the research purpose. The flame characteristics that were analyzed are its length, its luminosity, the temperature, the distribution of the droplets size and mainly the burning regime of the droplets in the flame. The experimental techniques that were used for these studies were shadow micro-photography, suction pyrometry and of total radiation, laser diffraction, 35 mm photography, and impact push. The analysis of the experimental results, together with the results of the application of a mathematical model, permitted to establish two parameters, that quantitatively related determine the burning regime of the droplets in a flame of sprays of residual heavy fuel oil. [Espanol] En este articulo se presenta una investigacion sobre la combustion de combustibles residuales pesados. El tipo de flamas estudiadas se obtuvieron mediante el quemado de sprays producidos por un atomizador disenado y calibrado especialmente para el proposito de la investigacion. Las caracteristicas de flama que se analizaron son la longitud, la luminosidad, la temperatura, la distribucion de tamano de gotas y, principalmente, el regimen de quemado de gotas en la flama. Las tecnicas experimentales que se usaron para estos estudios fueron microfotografia de sombras, pirometria de succion y de radiacion total, difraccion laser, fotografia de 35 mm y empuje de impacto. El analisis de resultados experimentales, junto con los resultados de la aplicacion de un modelo matematico, permitio establecer dos parametros, que relacionados cuantitativamente, determinan el regimen de quemado de gotas en una flama de sprays de combustible residual pesado.

  3. Utilization of stabilized municipal waste combustion ash residues as construction material

    International Nuclear Information System (INIS)

    Shieh, C.S.

    1992-01-01

    Stabilized municipal waste combustion (MWC) ash residues were investigated for their potential as construction material that can be beneficially used in terrestrial and marine environments. End-use products, such as patio stones, brick pavers, solid blocks, and reef units, were fabricated and tested for their engineering and chemical characteristics. engineering feasibility and environmental acceptability of using stabilized ash residues as construction material are discussed in this paper. Ash samples were collected from two mass-burn facilities and one refuse derived fuel (RDF) facility in Florida

  4. Beneficial Use and Recycling of Municipal Waste Combustion Residues - A Comprehensive Resource Document

    Energy Technology Data Exchange (ETDEWEB)

    Wiles, C.; Shepherd, P.

    1999-04-26

    This document summarizes information from worldwide sources on the beneficial use of residues from the combustion of municipal. The information presented, including results of numerous research projects, field demonstrations, and actual full-scale projects, demonstrates that the ash can be safely used. It includes data on ash characteristics, environmental considerations, guidance on selected ash use applications, and information on federal and state regulations and policies affecting ash use.

  5. Treatment of Lignin and Waste residues by Flash Pyrolysis

    DEFF Research Database (Denmark)

    Jensen, Peter Arendt; Trinh, Ngoc Trung; Dam-Johansen, Kim

    pyrolysis properties were compared with the pyrolysis properti es of wood and straw. The PCR treatment of sewage sludge provides an oil that can be used for energy pur poses and a solid residue rich in in organic nutrients that may be used as fertilizer product. By fast pyroly sis of lignin from the IBUS...... ethanol plant a bio-oil can be produced with oil yields of 36% (daf) and an oil en ergy recovery of 45%. This is a relatively low bio-oil yield compared to other feedstock’s, however, it may increase the value of the lignin residual product, such that the lignin char is used for combustion on the ethanol...... be operated at low rotational speed was constructed. The new rotor systems should make it easier to make an up-scaling of the process....

  6. List of Publicly Accessible Internet Sites Hosting Compliance Data and Information Required by the Disposal of Coal Combustion Residuals Rule

    Science.gov (United States)

    This page is to make accessible a list of the websites coal-fired power plants have created to post for the public to view with respect to their compliance with the disposal of coal combustion residuals final rule.

  7. Surgical treatment for residual or recurrent strabismus

    Directory of Open Access Journals (Sweden)

    Tao Wang

    2014-12-01

    Full Text Available Although the surgical treatment is a relatively effective and predictable method for correcting residual or recurrent strabismus, such as posterior fixation sutures, medial rectus marginal myotomy, unilateral or bilateral rectus re-recession and resection, unilateral lateral rectus recession and adjustable suture, no standard protocol is established for the surgical style. Different surgical approaches have been recommended for correcting residual or recurrent strabismus. The choice of the surgical procedure depends on the former operation pattern and the surgical dosages applied on the patients, residual or recurrent angle of deviation and the operator''s preference and experience. This review attempts to outline recent publications and current opinion in the management of residual or recurrent esotropia and exotropia.

  8. Residual water treatment for gamma radiation

    International Nuclear Information System (INIS)

    Mendez, L.

    1990-01-01

    The treatment of residual water by means of gamma radiation for its use in agricultural irrigation is evaluated. Measurements of physical, chemical, biological and microbiological contamination indicators were performed. For that, samples from the treatment center of residual water of San Juan de Miraflores were irradiated up to a 52.5 kGy dose. The study concludes that gamma radiation is effective to remove parasites and bacteria, but not for removal of the organic and inorganic matter. (author). 15 refs., 3 tabs., 4 figs

  9. Morphology, composition, and mixing state of primary particles from combustion sources - crop residue, wood, and solid waste.

    Science.gov (United States)

    Liu, Lei; Kong, Shaofei; Zhang, Yinxiao; Wang, Yuanyuan; Xu, Liang; Yan, Qin; Lingaswamy, A P; Shi, Zongbo; Lv, Senlin; Niu, Hongya; Shao, Longyi; Hu, Min; Zhang, Daizhou; Chen, Jianmin; Zhang, Xiaoye; Li, Weijun

    2017-07-11

    Morphology, composition, and mixing state of individual particles emitted from crop residue, wood, and solid waste combustion in a residential stove were analyzed using transmission electron microscopy (TEM). Our study showed that particles from crop residue and apple wood combustion were mainly organic matter (OM) in smoldering phase, whereas soot-OM internally mixed with K in flaming phase. Wild grass combustion in flaming phase released some Cl-rich-OM/soot particles and cardboard combustion released OM and S-rich particles. Interestingly, particles from hardwood (pear wood and bamboo) and softwood (cypress and pine wood) combustion were mainly soot and OM in the flaming phase, respectively. The combustion of foam boxes, rubber tires, and plastic bottles/bags in the flaming phase released large amounts of soot internally mixed with a small amount of OM, whereas the combustion of printed circuit boards and copper-core cables emitted large amounts of OM with Br-rich inclusions. In addition, the printed circuit board combustion released toxic metals containing Pb, Zn, Sn, and Sb. The results are important to document properties of primary particles from combustion sources, which can be used to trace the sources of ambient particles and to know their potential impacts in human health and radiative forcing in the air.

  10. Comparative study on systems of residual water treatment in the process industry by evaporation, using fossils fuels or solar energy; Estudio comparativo sobre sistemas de tratamiento de aguas residuales de la industria de procesamiento por evaporacion, utilizando combustibles fosiles o energia solar

    Energy Technology Data Exchange (ETDEWEB)

    Landgrave Romero, Julio; Canseco Contreras, Jose [Facultad de Quimica, UNAM (Mexico)

    1996-07-01

    The residual water treatment of the process industry, nowadays is an imminent necessity in our country. In the present study two different forms are considered to concentrate residual waters: multiple effect evaporation and solar evaporation. The use of solar evaporation lagoons is a good possibility to conserving energy by means of the diminution of fossil fuel consumption. The design basis of the evaporation systems via multiple effect, as well as solar evaporation, the results of the respective sizing and the estimation of the corresponding costs are presented. A practical case is described on the cooking of cotton linters (flock) [Spanish] El tratamiento de aguas residuales de la industria de proceso, hoy en dia es una necesidad inminente en nuestro pais. En el presente trabajo se consideran dos formas distintas para concentrar las aguas residuales: evaporacion de multiple efecto y evaporacion solar. El empleo de lagunas de evaporacion solar es una buena posibilidad para conseguir el ahorro de energia mediante disminucion del consumo de combustibles fosiles. Se presentan las bases de diseno de los sistemas de evaporacion via multiple efecto, asi como solar, los resultados del dimensionamiento respectivo y la estimacion de los costos correspondientes. Se describe un caso practico sobre el cocido de linters de algodon (borra)

  11. Combustion

    CERN Document Server

    Glassman, Irvin

    1987-01-01

    Combustion, Second Edition focuses on the underlying principles of combustion and covers topics ranging from chemical thermodynamics and flame temperatures to chemical kinetics, detonation, ignition, and oxidation characteristics of fuels. Diffusion flames, flame phenomena in premixed combustible gases, and combustion of nonvolatile fuels are also discussed. This book consists of nine chapters and begins by introducing the reader to heats of reaction and formation, free energy and the equilibrium constants, and flame temperature calculations. The next chapter explores the rates of reactio

  12. Waste treatment of combustion municipal wastes. Tratamiento de residuos provenientes de combustion de Residuos Solidos Urbanos

    Energy Technology Data Exchange (ETDEWEB)

    Brenot, M.

    The polluting substances that are initially in the smoke produced in the combustion of refuse, are newly met in the solid wastes coming from the treatment of this smoke. If it is necessary to avoid any risk of polluting transference, it is convenient to neutralize these wastes. There are three main systems that are nextly explained. (Author)

  13. Identification of accelerants, fuels and post-combustion residues using a colorimetric sensor array.

    Science.gov (United States)

    Li, Zheng; Jang, Minseok; Askim, Jon R; Suslick, Kenneth S

    2015-09-07

    A linear (1 × 36) colorimetric sensor array has been integrated with a pre-oxidation technique for detection and identification of a variety of fuels and post-combustion residues. The pre-oxidation method permits the conversion of fuel vapor into more detectable species and therefore greatly enhances the sensitivity of the sensor array. The pre-oxidation technique used a packed tube of chromic acid on an oxide support and was optimized in terms of the support and concentration. Excellent batch to batch reproducibility was observed for preparation and use of the disposable pre-oxidation tubes. Twenty automotive fuels including gasolines and diesel from five gasoline retailers were individually identifiable with no confusions or misclassifications in quintuplicate trials. Limits of detection were at sub-ppm concentrations for gasoline and diesel fuels. In addition, burning tests were performed on commonly used fire accelerants, and clear differentiation was achieved among both the fuels themselves and their volatile residues after burning.

  14. Computational fluid dynamics (CFD) analysis of the combustion process of a leather residuals gasification fuel gas: influence of fuel moisture content

    Energy Technology Data Exchange (ETDEWEB)

    Antonietti, Anderson Jose; Beskow, Arthur Bortolin; Silva, Cristiano Vitorino da [Universidade Regional Integrada do Alto Uruguai e das Missoes (URI), Erechim, RS (Brazil)], E-mails: arthur@uricer.edu.br, mlsperb@unisinos.br; Indrusiak, Maria Luiza Sperb [Universidade do Vale do Rio dos Sinos (UNISINOS), Sao Leopoldo, RS (Brazil)], E-mail: cristiano@uricer.edu.br

    2010-07-01

    This work presents a numerical study of the combustion process of leather residuals gasification gas, aiming the improvement of the process efficiency, considering different concentrations of water on the gas. The heating produced in this combustion process can be used to generation of thermal and/or electrical energy, for use at the leather industrial plant. However, the direct burning of this leather-residual-gas into the chambers is not straightforward. The alternative in development consists in processing this leather residuals by gasification or pyrolysis, separating the volatiles and products of incomplete combustion, for after use as fuel in a boiler. At these processes, different quantities of water can be used, resulting at different levels of moisture content in this fuel gas. This humidity can affect significantly the burning of this fuel, producing unburnt gases, as the carbon monoxide, or toxic gases as NOx, which must have their production minimized on the process, with the purpose of reducing the emission of pollutants to the atmosphere. Other environment-harmful-gases, remaining of the chemical treatment employed at leather manufacture, as cyanide, and hydrocarbons as toluene, must burn too, and the moisture content has influence on it. At this way, to increase understanding of the influence of moisture in the combustion process, it was made a numerical investigation study of reacting flow in the furnace, evaluating the temperature field, the chemical species concentration fields, flow mechanics and heat transfer at the process. The commercial CFD code CFX Ansys Inc. was used. Considering different moisture contents in the fuel used on the combustion process, with this study was possible to achieve the most efficient burning operation parameters, with improvement of combustion efficiency, and reduction of environmental harmful gases emissions. It was verified that the different moisture contents in the fuel gas demand different operation conditions

  15. Disposing of coal combustion residues in inactive surface mines: Effects on water quality

    International Nuclear Information System (INIS)

    Kim, A.G.; Ackman, T.E.

    1994-01-01

    The disposal of coal combustion residues (CCR) in surface and underground coal mines can provide a stable, low-maintenance alternative to landfills, benefiting the mining and electric power industries. The material may be able to improve water quality at acid generating abandoned or reclaimed coal mine sites. Most combustion residues are alkaline, and their addition to the subsurface environment could raise the pH, limiting the propagation of pyrite oxidizing bacteria and reducing the rate of acid generation. Many of these CCR are also pozzolanic, capable of forming cementitious grouts. Grouts injected into the buried spoil may decrease its permeability and porosity, diverting water away from the pyritic material. Both mechanisms, alkaline addition and water diversion, are capable of reducing the amount of acid produced at the disposal site. The US Bureau of Mines is cooperating in a test of subsurface injection of CCR into a reclaimed surface mine. Initially, a mixture of fly ash, lime, and acid mine drainage (AMD) sludge was injected. Lime was the source of calcium for the formation of the pozzolanic grout. Changes in water quality parameters (pH, acidity, anions, and trace metals) in water samples from wells and seeps indicate a small but significant improvement after CCR injection. Changes in the concentration of heavy metals in the water flowing across the site were apparently influenced by the presence of flyash

  16. Characterization of residues from waste combustion in fluidized bed boilers. Evaluation report

    International Nuclear Information System (INIS)

    Hagman, U.; Elander, P.

    1996-04-01

    In this report a thorough characterization of the solid residues from municipal solid waste combustion in a Kvaerner EnviroPower bubbling fluidized bed boiler in Lidkoeping, is presented. Three different end products are generated, namely bottom ash, cyclone ash, and filter ash. The bottom ash, consisting of bed ash and hopper ash, is screened and useful bed material recycled. In the characterization, also the primary constituents bed ash and hopper ash have been included. A chemical characterization have been performed including total inorganic contents, content of unburnt matter, leaching behaviour (availability tests, column tests, pH-static tests) and leaching tests according to certain standards for classification (AFX31-210, DIN38414, TCLP). Physical characterization have included grain size distribution, grain density, compaction properties and stabilization of cyclone ash with subsequent testing of comprehensive strength and saturated hydraulic conductivity. From an environmental point of view, the quality of the bottom ash and probably the cyclone ash from fluidized bed combustion as determined in this study, indicate a potential for utilization. Utilization of the bottom ash could be accepted in certain countries, e.g. France, according to their current limit values. In other countries, e.g. Sweden, no general limit values are given and utilization have to be applied for in each case. The judgement is then based, not only on total contents in the residue and its leaching behaviour, but also on the specific environmental conditions at the site. 7 refs, 17 figs, 12 tabs

  17. Acid digestion and pressurization control in combustible radwaste treatment

    International Nuclear Information System (INIS)

    Allen, C.R.; Cowan, R.G.; Grelecki, C.J.

    1978-01-01

    Acid digestion has been developed to reduce the volume of combustible nuclear waste materials, while converting them to an inert, noncombustible residue. A 100 kg/day test unit has recently been constructed to process radioactively contaminated combustible wastes. The unit, called the Radioactive Acid Digestion Test Unit (RADTU) was completed in September, 1977, and is currently undergoing nonradioactive shakedown tests. Radioactive operation is expected in May, 1978. Because of uncertainties in waste composition and reactivity, the system was required to contain pressurizations. This led to the development of a simple and inexpensive system, which is capable of attenuating a shock wave from a full scale vapor detonation. The system has potential application in a wide spectrum of chemical reactors, since the fabrication materials are resistant to a very wide range of corrosive chemical attack

  18. Combustible radioactive waste treatment by incineration and chemical digestion

    International Nuclear Information System (INIS)

    Stretz, L.A.; Crippen, M.D.; Allen, C.R.

    1980-01-01

    A review is given of present and planned combustible radioactive waste treatment systems in the US. Advantages and disadvantages of various systems are considered. Design waste streams are discussed in relation to waste composition, radioactive contaminants by amount and type, and special operating problems caused by the waste

  19. COMPARISON OF PARTICLE SIZE DISTRIBUTIONS AND ELEMENTAL PARTITIONING FROM THE COMBUSTION OF PULVERIZED COAL AND RESIDUAL FUEL OIL

    Science.gov (United States)

    The paper gives results of experimental efforts in which three coals and a residual fuel oil were combusted in three different systems simulating process and utility boilers. Particloe size distributions (PSDs) were determined using atmospheric and low-pressure impaction, electr...

  20. Characterization of carbonaceous combustion residues. I. Morphological, elemental and spectroscopic features.

    Science.gov (United States)

    Fernandes, Milena B; Skjemstad, Jan O; Johnson, Bruce B; Wells, John D; Brooks, Peter

    2003-06-01

    Scanning electron microscopy, surface area determination, elemental analysis, organic matter extraction and solid-state cross polarization/magic angle spinning and Bloch decay/magic angle spinning 13C nuclear magnetic resonance (NMR) spectroscopy were used to investigate distinctive features among carbonaceous combustion residues. Black carbon (BC) samples included diesel soot, urban dust, carbon black, chimney soot, vegetation fire residues, wood and straw charcoals. Particles varied from small spheres (100 m(2)/g), to large layered structures in plant-derived BC (generally 1 micrometer) liquid-like structures, while spherules >100 nm were unique to urban dust. The ratios of amorphous to soot carbon (SC) (isolated by thermal degradation) were not necessarily correlated with the degree of aromaticity estimated from H/C ratios. In particular, values of SC in diesel soot were clearly overestimated. Solvent-extractable organic matter (SEOM) was 13% for urban dust, chimney and diesel soot. SEOM is thought to clog pores or to form large waxy globules, hence reducing surface areas. The ratio of polar/nonpolar SEOM was generally 30 for plant-derived BC. NMR analysis revealed essentially one chemical shift in the aromatic C region of charcoals, while diesel soot also showed important aliphatic contributions. Aliphatic and oxygenated C predominated over aryl C in urban dust and chimney soot. These morphological and chemical characteristics of the BC samples are discussed in terms of their environmental implications.

  1. Leaching and soil/groundwater transport of contaminants from coal combustion residues

    International Nuclear Information System (INIS)

    Hjelmar, O.; Hansen, E.A.; Larsen, F.; Thomassen, H.

    1992-01-01

    In this project the results of accelerated laboratory leaching tests on coal fly ash and flue gas desulfurization (FGD) products from the spray dryer absorption process (SDA) were evaluated by comparison to the results of large scale lysimeter leaching tests on the same residues. The mobility of chromium and molybdenum - two of the kev contaminants of coal combustion residue leachates - in various typical soil types was investigated by batch and column methods in the laboratory. Some of the results were confirmed by field observations at an old coal fly ash disposal site and by a lysimeter attenuation test with coal fly ash leachate on a clayed till. A large number of groundwater transport models and geochemical models were reviewed, and two of the models (Gove-Stollenwerk and CHMTRNS) were modified and adjusted and used to simulate column attenuation tests performed in the laboratory. One of the models (Grove-Stollenwerk) was used to illustrate a recommended method of environmental impact assessment, using lysimeter leaching data and laboratory column attenuation data to describe the emission and migration of Mo from a coal fly ash disposal site

  2. The Behavior of Mercury in Coal Combustion Residue-Contaminated Sediments

    Science.gov (United States)

    Gofstein, T.; Heyes, A.

    2014-12-01

    Coal combustion residues (CCRs), the products of coal combustion, contain high concentrations of heavy metals such as mercury. Recent structural failures of on-site containment ponds and leaching of CCRs has potentially endangered the health of adjacent water bodies. This study examines the influence of CCR enrichment of river sediments through the study of mercury, an abundant constituent of CCRs, and the concomitant production of methylmercury. We hypothesized that CCR contamination increases the exposure to mercury for aquatic life through leaching and resuspension mechanisms. Resuspension experiments were conducted using CCR-contaminated sediments from the Dan River and uncontaminated sediments enriched with 0%, 10%, and 30% CCRs in the laboratory. Sediments were sieved to obtain the silt-clay fraction, which was then resuspended in solution with a dispersant to obtain the separate silt and clay fractions and then analyzed for total mercury concentrations. We found that CCR particles and the mercury they contain are present primarily in the silt and clay fractions of sediment and there is a direct relationship between CCR concentrations and total mercury concentrations. These findings have implications for both the bioavailability of mercury to methylating bacteria, higher organisms prone to direct ingestion of fine particles, CCR spill event remediation, current industrial waste disposal practices, and further research required in this field. Our seven day incubations of river sediment cores enriched with CCRs did not increase methylmercury in porewater above controls, suggesting that there is no immediate risk of increased methylmercury bioaccumulation, however this does not necessarily reflect the long-term effects of CCRs on river ecology, which requires further research.

  3. Properties of Chemically Combusted Calcium Carbide Residue and Its Influence on Cement Properties

    Directory of Open Access Journals (Sweden)

    Hongfang Sun

    2015-02-01

    Full Text Available Calcium carbide residue (CCR is a waste by-product from acetylene gas production. The main component of CCR is Ca(OH2, which can react with siliceous materials through pozzolanic reactions, resulting in a product similar to those obtained from the cement hydration process. Thus, it is possible to use CCR as a substitute for Portland cement in concrete. In this research, we synthesized CCR and silica fume through a chemical combustion technique to produce a new reactive cementitious powder (RCP. The properties of paste and mortar in fresh and hardened states (setting time, shrinkage, and compressive strength with 5% cement replacement by RCP were evaluated. The hydration of RCP and OPC (Ordinary Portland Cement pastes was also examined through SEM (scanning electron microscope. Test results showed that in comparison to control OPC mix, the hydration products for the RCP mix took longer to formulate. The initial and final setting times were prolonged, while the drying shrinkage was significantly reduced. The compressive strength at the age of 45 days for RCP mortar mix was found to be higher than that of OPC mortar and OPC mortar with silica fume mix by 10% and 8%, respectively. Therefore, the synthesized RCP was proved to be a sustainable active cementitious powder for the strength enhanced of building materials, which will result in the diversion of significant quantities of this by-product from landfills.

  4. Boron and strontium isotopic characterization of coal combustion residuals: validation of new environmental tracers.

    Science.gov (United States)

    Ruhl, Laura S; Dwyer, Gary S; Hsu-Kim, Heileen; Hower, James C; Vengosh, Avner

    2014-12-16

    In the U.S., coal fired power plants produce over 136 million tons of coal combustion residuals (CCRs) annually. CCRs are enriched in toxic elements, and their leachates can have significant impacts on water quality. Here we report the boron and strontium isotopic ratios of leaching experiments on CCRs from a variety of coal sources (Appalachian, Illinois, and Powder River Basins). CCR leachates had a mostly negative δ(11)B, ranging from -17.6 to +6.3‰, and (87)Sr/(86)Sr ranging from 0.70975 to 0.71251. Additionally, we utilized these isotopic ratios for tracing CCR contaminants in different environments: (1) the 2008 Tennessee Valley Authority (TVA) coal ash spill affected waters; (2) CCR effluents from power plants in Tennessee and North Carolina; (3) lakes and rivers affected by CCR effluents in North Carolina; and (4) porewater extracted from sediments in lakes affected by CCRs. The boron isotopes measured in these environments had a distinctive negative δ(11)B signature relative to background waters. In contrast (87)Sr/(86)Sr ratios in CCRs were not always exclusively different from background, limiting their use as a CCR tracer. This investigation demonstrates the validity of the combined geochemical and isotopic approach as a unique and practical identification method for delineating and evaluating the environmental impact of CCRs.

  5. Characterisation of polycyclic aromatic hydrocarbons in flue gas and residues of a full scale fluidized bed combustor combusting non-hazardous industrial waste.

    Science.gov (United States)

    Van Caneghem, J; Vandecasteele, C

    2014-11-01

    This paper studies the fate of PAHs in full scale incinerators by analysing the concentration of the 16 EPA-PAHs in both the input waste and all the outputs of a full scale Fluidized Bed Combustor (FBC). Of the analysed waste inputs i.e. Waste Water Treatment (WWT) sludge, Refuse Derived Fuel (RDF) and Automotive Shredder Residue (ASR), RDF and ASR were the main PAH sources, with phenanthrene, fluoranthene and pyrene being the most important PAHs. In the flue gas sampled at the stack, naphthalene was the only predominant PAH, indicating that the PAHs in FBC's combustion gas were newly formed and did not remain from the input waste. Of the other outputs, the boiler and fly ash contained no detectable levels of PAHs, whereas the flue gas cleaning residue contained only low concentrations of naphthalene, probably adsorbed from the flue gas. The PAH fingerprint of the bottom ash corresponded rather well to the PAH fingerprint of the RDF and ASR, indicating that the PAHs in this output, in contrast to the other outputs, were mainly remainders from the PAHs in the waste inputs. A PAH mass balance showed that the total PAH input/output ratio of the FBC ranged from about 100 to about 2600 depending on the waste input composition and the obtained combustion conditions. In all cases, the FBC was clearly a net PAH sink. Copyright © 2014 Elsevier Ltd. All rights reserved.

  6. The stability of drinking water treatment residue with ozone treatment.

    Science.gov (United States)

    Liu, Xin; Wu, Yu; He, Rui; Jiang, He-Long; Wang, Changhui

    2017-06-12

    The best management of drinking water treatment residue (DWTR) in environmental remediation should be based on comprehensively understanding the effectiveness and risk of DWTR. In this study, the variation in physicochemical properties, metal lability, and adsorption capability of DWTR under oxidizing condition were investigated. The oxidizing condition was set up using ozone treatment, and the laboratory incubation test were performed within 50 d in association with thermogravimetry, Fourier Transform Infrared Spectrometry, specific surface area and porosity analyzer, fractionation, and P adsorption test. The results showed that ozone treatment had limited effect on the properties of organic matter, the lability of Al, Cu, and Fe, the P adsorption capability, and the distributions of the adsorbed P in DWTR, but the treatment increased N 2 sorption/desorption, specific surface area, total pore volume of DWTR and led to the transformation of Mn from acid-soluble to reducible fractions. These findings demonstrated that DWTR generally kept stable under oxidizing environment; even oxidizing environment may induce a tendency of increasing the adsorption capability and decreasing the environmental risk of DWTR. Accordingly, the effectiveness and safety of DWTR can be maintained under natural aerobic environment, and DWTR is a reliable adsorbent that could be recycled in environmental remediation.

  7. JV Task 5 - Evaluation of Residual Oil Fly Ash As A Mercury Sorbent For Coal Combustion Flue Gas

    Energy Technology Data Exchange (ETDEWEB)

    Robert Patton

    2006-12-31

    The mercury adsorption capacity of a residual oil fly ash (ROFA) sample collected form Florida Power and Light Company's Port Everglades Power Plant was evaluated using a bituminous coal combustion flue gas simulator and fixed-bed testing protocol. A size-segregated (>38 {micro}g) fraction of ROFA was ground to a fine powder and brominated to potentially enhance mercury capture. The ROFA and brominated-ROFA were ineffective in capturing or oxidizing the Hg{sup 0} present in a simulated bituminous coal combustion flue gas. In contrast, a commercially available DARCO{reg_sign} FGD initially adsorbed Hg{sup 0} for about an hour and then catalyzed Hg{sup 0} oxidation to produce Hg{sup 2+}. Apparently, the unburned carbon in ROFA needs to be more rigorously activated in order for it to effectively capture and/or oxidize Hg{sup 0}.

  8. A stochastic logical system approach to model and optimal control of cyclic variation of residual gas fraction in combustion engines

    International Nuclear Information System (INIS)

    Wu, Yuhu; Kumar, Madan; Shen, Tielong

    2016-01-01

    Highlights: • An in-cylinder pressure based measuring method for the RGF is derived. • A stochastic logical dynamical model is proposed to represent the transient behavior of the RGF. • The receding horizon controller is designed to reduce the variance of the RGF. • The effectiveness of the proposed model and control approach is validated by the experimental evidence. - Abstract: In four stroke internal combustion engines, residual gas from the previous cycle is an important factor influencing the combustion quality of the current cycle, and the residual gas fraction (RGF) is a popular index to monitor the influence of residual gas. This paper investigates the cycle-to-cycle transient behavior of the RGF in the view of systems theory and proposes a multi-valued logic-based control strategy for attenuation of RGF fluctuation. First, an in-cylinder pressure sensor-based method for measuring the RGF is provided by following the physics of the in-cylinder transient state of four-stroke internal combustion engines. Then, the stochastic property of the RGF is examined based on statistical data obtained by conducting experiments on a full-scale gasoline engine test bench. Based on the observation of the examination, a stochastic logical transient model is proposed to represent the cycle-to-cycle transient behavior of the RGF, and with the model an optimal feedback control law, which targets on rejection of the RGF fluctuation, is derived in the framework of stochastic logical system theory. Finally, experimental results are demonstrated to show the effectiveness of the proposed model and the control strategy.

  9. Biological treatment of crop residues for ruminant feeding: A review ...

    African Journals Online (AJOL)

    Crop residues are often referred to as 'lignocellulosics' as they are rich in cellulose which is bound with a biopolymer lignin. Rumen microbiota (bacteria, protozoa and fungi), even with their hydrolytic enzymes, are not very competent enough to break these bonds efficiently. Biological treatment of such crop residues using ...

  10. Nickel, sulfur and vanadium determination in residues from crude oil distillation by ICPOES after microwave-induced combustion

    International Nuclear Information System (INIS)

    Mello, P.A.; Pereira, J.S.F.; Dressler, V.L.; Flores, E.M.M.

    2009-01-01

    Full text: A microwave-induced combustion method is proposed for digestion of atmospheric and vacuum residues from heavy crude oil for simultaneous Ni, S and V determination by ICPOES. Ammonium nitrate solution (6 M, 50 μl) was used as igniter. Operational parameters were investigated as maximum sample mass, initial O 2 pressure, type and concentration of absorbing solutions (H 2 O, H 2 O 2 , and HNO 3 ) and the necessity of additional reflux steps. Accuracy was better than 98 %. Limits of detection were 0.2, 2 and 0.1 mg kg -1 for Ni, S and V, respectively. (author)

  11. On the ASR and ASR thermal residues characterization of full scale treatment plant.

    Science.gov (United States)

    Mancini, G; Viotti, P; Luciano, A; Fino, D

    2014-02-01

    In order to obtain 85% recycling, several procedures on Automotive Shredder Residue (ASR) could be implemented, such as advanced metal and polymer recovery, mechanical recycling, pyrolysis, the direct use of ASR in the cement industry, and/or the direct use of ASR as a secondary raw material. However, many of these recovery options appear to be limited, due to the possible low acceptability of ASR based products on the market. The recovery of bottom ash and slag after an ASR thermal treatment is an option that is not usually considered in most countries (e.g. Italy) due to the excessive amount of contaminants, especially metals. The purpose of this paper is to provide information on the characteristics of ASR and its full-scale incineration residues. Experiments have been carried out, in two different experimental campaigns, in a full-scale tyre incineration plant specifically modified to treat ASR waste. Detailed analysis of ASR samples and combustion residues were carried out and compared with literature data. On the basis of the analytical results, the slag and bottom ash from the combustion process have been classified as non-hazardous wastes, according to the EU waste acceptance criteria (WAC), and therefore after further tests could be used in future in the construction industry. It has also been concluded that ASR bottom ash (EWC - European Waste Catalogue - code 19 01 12) could be landfilled in SNRHW (stabilized non-reactive hazardous waste) cells or used as raw material for road construction, with or without further treatment for the removal of heavy metals. In the case of fly ash from boiler or Air Pollution Control (APC) residues, it has been found that the Cd, Pb and Zn concentrations exceeded regulatory leaching test limits therefore their removal, or a stabilization process, would be essential prior to landfilling the use of these residues as construction material. Copyright © 2013 Elsevier Ltd. All rights reserved.

  12. Naturally occuring radioactivity in residues of drinking water treatment

    International Nuclear Information System (INIS)

    Vornehm, C.; Mallick, R.

    2009-01-01

    In the course of a research project about 500 residues of drinking water treatment from approx. 400 water supply companies in Bavaria were investigated on naturally occurring radioactivity. For each residue the effective dose for workers was evaluated for each residue. The results show that increased activities, particularly of Radium-226, can be found in the material. The dose due to the exposure to the residues, which mostly result from the backwashing of filters, is below the reference value of 1 mSv/a, which can be used according to paragraph 97 of the German radiation protection standard. During the project the quantity of residues in Bavaria and the ways of their disposal were evaluated. In addition the relation between the amount of natural radioisotopes in the residues and the geological and hydrochemical conditions of the water catchment area was pointed out. (orig.)

  13. Treatment Method for Fermi Barrel Sodium Metal Residues

    Energy Technology Data Exchange (ETDEWEB)

    Steven R. Sherman; Collin J. Knight

    2005-06-01

    Fermi barrels are 55-gallon drums that once contained bulk sodium metal from the shutdown Fermi 1 breeder reactor facility, and now contain residual sodium metal and other sodium/air reaction products. This report provides a residual sodium treatment method and proposed quality assurance steps that will ensure that all residual sodium is deactivated and removed from the Fermi barrels before disposal. The treatment method is the application of humidified carbon dioxide to the residual sodium followed by a water wash. The experimental application of the treatment method to six Fermi barrels is discussed, and recommendations are provided for further testing and evaluation of the method. Though more testing would allow for a greater refinement of the treatment technique, enough data has been gathered from the tests already performed to prove that 100% compliance with stated waste criteria can be achieved.

  14. Fly ash classification efficiency of electrostatic precipitators in fluidized bed combustion of peat, wood, and forest residues.

    Science.gov (United States)

    Ohenoja, Katja; Körkkö, Mika; Wigren, Valter; Österbacka, Jan; Illikainen, Mirja

    2018-01-15

    The increasing use of biomasses in the production of electricity and heat results in an increased amount of burning residue, fly ash which disposal is becoming more and more restricted and expensive. Therefore, there is a great interest in utilizing fly ashes instead of just disposing of it. This study aimed to establish whether the utilization of fly ash from the fluidized bed combustion of peat, wood, and forest residues can be improved by electrostatic precipitator separation of sulfate, chloride, and some detrimental metals. Classification selectivity calculations of electrostatic precipitators for three different fuel mixtures from two different power plants were performed by using Nelson's and Karnis's selectivity indices. Results showed that all fly ashes behaved similarly in the electrostatic separation process SiO 2 resulted in coarse fractions with Nelson's selectivity of 0.2 or more, while sulfate, chloride, and the studied detrimental metals (arsenic, cadmium, and lead) enriched into fine fractions with varying selectivity from 0.2 to 0.65. Overall, the results of this study suggest that it is possible to improve the utilization potential of fly ashes from fluidized bed combustion in concrete, fertilizer, and earth construction applications by using electrostatic precipitators for the fractionating of fly ashes in addition to their initial function of collecting fly ash particles from flue gases. The separation of the finer fractions (ESP 2 and 3) from ESP 1 field fly ash is recommended. Copyright © 2017 Elsevier Ltd. All rights reserved.

  15. Environmental performance of the Kvaerner BFB boilers for MSW combustion -- Analysis of gaseous emissions and solid residues

    International Nuclear Information System (INIS)

    Lundberg, M.; Hagman, U.; Andersson, B.A.; Olofsson, J.

    1997-01-01

    Kvaerner Pulping AB (formerly Kvaerner EnviroPower AB) has, due to the stringent demands on emissions performance, developed a state-of-the-art bubbling fluidized bed boiler (BFB) designed for waste fuel firing with very low emissions to the air. A complete evaluation of the environmental performance of the Kvaerner BFB technique for MSW combustion is now possible thanks to a thorough characterization study of the solid residues from the Lidkoeping plant. This paper gives an overall mapping of the emissions performance. Data from the operating plants on solid residue characteristics and leachability, heavy metal and dioxin emissions, nitrogen oxides, carbon monoxide, acid gases, and other emissions to air are presented. Comparisons are made with legislative limits and data from the mass burning technique. It is concluded that the emissions are low compared both with data from traditional mass burn incinerators and with legislative limits in the USA and Europe. Furthermore, the bottom and cyclone ash characteristics are shown not to cause any particular problem from an environmental point of view, and that the leachability is well below the existing legislative limits in Europe and the USA. The results show that fluidized bed combustion of municipal solid waste is a very competitive alternative to the traditional mass burning technique in every respect

  16. Energy Generation from Horse Husbandry Residues by Anaerobic Digestion, Combustion, and an Integrated Approach

    Directory of Open Access Journals (Sweden)

    Meike Nitsche

    2017-02-01

    Full Text Available Horse-related activities often occur close to urban areas, where acreage for horse manure disposal is scarce, and subsequently alternative recovery options are necessary. Anaerobic digestion, direct combustion, and the integrated generation of solid fuel and biogas from biomass (IFBB process are potential techniques focusing on energy provision. In this study, samples of horse faeces were analysed for chemical composition as pure feedstock and in mixture with straw or wood shavings, as well as for energy yield by biogas production or from combustion of solid fuel. It was observed that chemical properties of faeces, in a mixture with wood shavings, were promising for direct combustion, but achieved low methane yields. The methane yield of pure faeces and the straw mixture was 222.33 ± 13.60 and 233.01 ± 31.32 lN·kg-1 volatile solids (VSadded, respectively. The IFBB process divided the biomass into a press cake with reduced mineral concentration and a press fluid. Methane yields of press fluids were low (108.2 lN·kg-1 VSadded, on average. The chemical composition of the press cake allowed for combustion and led to a higher gross energy potential than anaerobic digestion (two-fold higher for pure manure and the mixture with straw, and five-fold higher for the mixture with shavings. Consequently, the gross energy potential of IFBB is higher compared to anaerobic digestion, however it should be noted that local conditions might favour the implementation of anaerobic digestion.

  17. Are pesticide residues in honey related to oilseed rape treatments?

    Science.gov (United States)

    Karise, Reet; Raimets, Risto; Bartkevics, Vadims; Pugajeva, Iveta; Pihlik, Priit; Keres, Indrek; Williams, Ingrid H; Viinalass, Haldja; Mänd, Marika

    2017-12-01

    Pesticide treatments before and during the flowering of honey bee forage crops may lead to residues in honey. In northern regions oilseed rape belongs to the main forage crops that is mostly cultivated by means of intensive agriculture, including several pesticide treatments. However, in addition to the focal forage crops, pesticides from non-forage crops can spread to wild flowers around fields, and thus the residues in honey would reflect the whole range of pesticides used in the agricultural landscape. The aim of our study was to clarify which currently used pesticides are present in honey gathered from heterogeneous agricultural landscapes after the end of flowering of oilseed crops. Honey samples (N = 33) were collected from beehives of Estonia during 2013 and 2014, and analysed for residues of 47 currently used agricultural pesticides using the multiresidue method with HPLC-MS/MS and GC-MS and a single residue method for glyphosate, aminopyralid and clopyralid. Residues of eight different active ingredients with representatives from all three basic pesticide classes were determined. Although no correlation was detected between the cumulative amount of pesticide residues and percent of oilseed crops in the foraging territory, most of the residues are those allowed for oilseed rape treatments. Among all pesticides, herbicide residues prevailed in 2013 but not in 2014. Despite the relatively small agricultural impact of Estonia, the detected levels of pesticide residues sometimes exceeded maximum residue level; however, these concentrations do not pose a health risk to consumers, also acute toxicity to honey bees would be very unlikely. Copyright © 2017 Elsevier Ltd. All rights reserved.

  18. The use of sewage sludge as additive to avoid operational problems at combustion of shredder residues

    International Nuclear Information System (INIS)

    Gyllenhammar, Marianne

    2010-01-01

    When shredder light fraction (SLF) from recovery of metal scrap is energy recovered it is usually mixed with more than 90% of other wastes. SLF is a fuel with high energy content but also with relatively high chlorine and metal content and could cause deposit and corrosion problems in incineration plants. Sewage sludge has previously been shown to reduce deposition and corrosion problems in combustion of alkali and chlorine containing biomass. In this work 20 % SLF (by energy content) has been combusted together with municipal solid waste and industrial wastes, with and without addition of 3 % (by energy content) sewage sludge. The initial fireside corrosion rate was then compared to the corrosion rate during combustion of the normal fuel mix, i.e. only municipal solid waste and industrial wastes. The tests were done at the 20 MW fluidized bed boiler of Lidkoping heat production plant. During the tests air-cooled corrosion and deposit probes were exposed for 24 hours. Deposit probes were placed at three different flue gas temperatures - in the combustion chamber, upstream and downstream the convection pass. The corrosion probes were placed upstream the convection pass and on the probes there were three different materials at three different water temperatures (280, 350 and 420 degree Celsius). The tests showed that sewage sludge could help avoiding deposition and corrosion problems when incinerating SLF. The amount of deposits was reduced and the content of the deposits was less corrosive when sewage sludge was added. The project was financed by Waste Refinery as a collaboration project between Stena Metall AB, Metso AB, High Temperature Corrosion Center at Chalmers University of Technology, SP Technical Research Institute of Sweden and Lidkopings Varmeverk. (author)

  19. Soil and air temperature and biomass after residue treatment.

    Science.gov (United States)

    W.B. Fowler; J.D. Helvey

    1981-01-01

    Air temperature at 0.5 m and soil temperature at 0.01 m were measured during May and early June after forest harvest on four residue treatment sites and a control. Broadcast burning or burning in piles increased daily accumulation of heat in air while scattered chips and scarified and cleared treatments were equal to the control (broadcast, untreated slash). During mid...

  20. Anaerobia Treatments of the domestic residual waters. Limitations potentialities

    International Nuclear Information System (INIS)

    Giraldo Gomez, Eugenio

    1993-01-01

    The quick growth of the Latin American cities has prevented that an appropriate covering of public services is achieved for the whole population, One of the undesirable consequences of this situation is the indiscriminate discharge from the domestic and industrial residual waters to the nearest bodies of water with its consequent deterioration and with disastrous consequences about the ecology and the public health. The developed countries have controlled this situation using systems of purification of the residual waters previously to their discharge in the receptor source. The same as the technology of the evacuation of the served waters, they have become numerous efforts for the application of the purification systems used in the countries developed to the socioeconomic, climatic and cultural conditions of our means. One of the results obtained in these efforts is the economic inability of the municipalities to pay the high investment costs and of operation of the traditional systems for the treatment of the residual waters. Contrary to another type of public services, the treatment of the residual waters needs of appropriate technological solutions for the Climatic and socioeconomic means of the developing countries, One of the technological alternatives for the purification of the residual waters that has had a great development in the last decades has been that of the biological treatments in t anaerobia ambient. The objective of this contribution is to present, to author's trial, the limitations and potentialities of this technology type with special emphasis in the case of the domestic residual waters

  1. Characterization of residues from thermal treatment of treated wood and extraction of Cu, Cr, As and Zn

    DEFF Research Database (Denmark)

    Ottosen, Lisbeth M.; Pedersen, Anne Juul; Christensen, Iben Vernegren

    2005-01-01

    , that the charcoal contained a high concentration of Zn, probably from paint. Chemical extraction experiments in HNO were conducted with the charcoal and it was found that the order of extraction (in percentage) was Zn > Cu > As > Cr. A SEM/EDX investigation of the mixed ash from combustion showed the presence...... a matter to cope with when methods to avoid As emission are implemented: the residues with increased concentrations of Cu, Cr and As. In the present paper two different residues after thermal treatment are characterized: a mixed bottom and fly ash from combustion of CCA impregnated wood, and a charcoal...... form in a small layer on the surface of some matrix particles indicating condensation of volatile Cu species. Chemical extraction with inorganic acids showed the order of percentages mobilized as: As > Cu > Cr....

  2. Investigation on the fast co-pyrolysis of sewage sludge with biomass and the combustion reactivity of residual char.

    Science.gov (United States)

    Deng, Shuanghui; Tan, Houzhang; Wang, Xuebin; Yang, Fuxin; Cao, Ruijie; Wang, Zhao; Ruan, Renhui

    2017-09-01

    Gaining the valuable fuels from sewage sludge is a promising method. In this work, the fast pyrolysis characteristics of sewage sludge (SS), wheat straw (WS) and their mixtures in different proportions were carried out in a drop-tube reactor. The combustion reactivity of the residual char obtained was investigated in a thermogravimetric analyzer (TGA). Results indicate that SS and WS at different pyrolysis temperatures yielded different characteristic gas compositions and product distributions. The co-pyrolysis of SS with WS showed that there existed a synergistic effect in terms of higher gas and bio-oil yields and lower char yield, especially at the WS adding percentage of 80wt%. The addition of WS to SS increased the carbon content in the SS char and improved char porous structures, resulting in an improvement in the combustion reactivity of the SS char. The research results can be used to promote co-utilization of sewage sludge and biomass. Copyright © 2017. Published by Elsevier Ltd.

  3. Predicting the residual aluminum level in water treatment process

    OpenAIRE

    J. Tomperi; M. Pelo; K. Leiviskä

    2013-01-01

    In water treatment processes, aluminum salts are widely used as coagulation chemical. High dose of aluminum has been proved to be at least a minor health risk and some evidence points out that aluminum could increase the risk of Alzheimer's disease. Thus it is important to minimize the amount of residual aluminum in drinking water and water used at food industry. In this study, the data of a water treatment plant (WTP) was analyzed and the residual aluminum in drinking water was predicted usi...

  4. Predicting the residual aluminum level in water treatment process

    OpenAIRE

    J. Tomperi; M. Pelo; K. Leiviskä

    2012-01-01

    In water treatment processes, aluminum salts are widely used as coagulation chemical. High dose of aluminum has been proved to be at least a minor health risk and some evidence points out that aluminum could increase the risk of Alzheimer's disease thus it is important to minimize the amount of residual aluminum in drinking water and water used at food industry. In this study, the data of a water treatment plant (WTP) was analyzed and the residual aluminum in drinking water was predicted usin...

  5. TRP0033 - PCI Coal Combustion Behavior and Residual Coal Char Carryover in the Blast Furnace of 3 American Steel Companies during Pulverized Coal Injection (PCI) at High Rates

    Energy Technology Data Exchange (ETDEWEB)

    Veena Sahajwalla; Sushil Gupta

    2005-04-15

    Combustion behavior of pulverized coals (PC), gasification and thermal annealing of cokes were investigated under controlled environments. Physical and chemical properties of PCI, coke and carbon residues of blast furnace dust/sludge samples were characterized. The strong influence of carbon structure and minerals on PCI reactivity was demonstrated. A technique to characterize char carryover in off gas emissions was established.

  6. Some techniques used in the treatment of phenolic waters residual

    International Nuclear Information System (INIS)

    Alzate S, Rafael A.; Botero, Carlos Andre

    2000-01-01

    The current state of the diverse processes of treatment of phenolic waters residual is presented, beginning with the methods traditionally employees, until finishing with those but recent innovations, which have been derived of the necessity of increasing the removal of these pollutants without increasing the costs of such processes in excessive form

  7. Characterisation of some South African water treatment residues ...

    African Journals Online (AJOL)

    Land application of water treatment residue (WTR) the by-product from the production of potable water, is becoming the preferred method of disposal, as there are environmental concerns and increasingly high costs associated with other disposal options. However, before WTR can be applied to land, consideration needs ...

  8. [Emission inventory of greenhouse gases from agricultural residues combustion: a case study of Jiangsu Province].

    Science.gov (United States)

    Liu, Li-hua; Jiang, Jing-yan; Zong, Liang-gang

    2011-05-01

    Burning of agricultural crop residues was a major source greenhouse gases. In this study, the proportion of crop straws (rice, wheat, maize, oil rape, cotton and soja) in Jiangsu used as household fuel and direct open burning in different periods (1990-1995, 1996-2000, 2001-2005 and 2006-2008) was estimated through questionnaire. The emission factors of CO2, CO, CH4 and NO20 from the above six types of crop straws were calculated by the simulated burning experiment. Thus the emission inventory of greenhouse gases from crop straws burning was established according to above the burning percentages and emission factors, ratios of dry residues to production and crop productions of different periods in Jiangsu province. Results indicated that emission factors of CO2, CO, CH4 and N2O depended on crop straw type. The emission factors of CO2 and CH4 were higher for oil rape straw than the other straws, while the maize and the rice straw had the higher N2O and CO emission factor. Emission inventory of greenhouse gases from agricultural residues burning in Jiangsu province showed, the annual average global warming potential (GWP) of six tested crop straws were estimated to be 9.18 (rice straw), 4.35 (wheat straw), 2.55 (maize straw), 1.63 (oil rape straw), 0.55 (cotton straw) and 0. 39 (soja straw) Tg CO2 equivalent, respectively. Among the four study periods, the annual average GWP had no obvious difference between the 1990-1995 and 2006-2008 periods, while the maximal annual average GWP (23.83 Tg CO2 equivalent) happened in the 1996-2000 period, and the minimum (20.30 Tg CO2 equivalent) in 1996-2000 period.

  9. Combustion characteristics of Athabasca froth treatment tailings in a simulated fluidilized bed

    Energy Technology Data Exchange (ETDEWEB)

    Esmaeili, P.; Ghosh, M.; Speirs, B. C. [Imperial Oil Resources (Canada); Leon, M. A.; Rao, S.; Dutta, A.; Basu, P. [Greenfield Research Inc. (Canada)

    2011-07-01

    In surface-mined oil sands, a stream of water, asphaltenes, solids and residual bitumen/solvent, known as PFT tailings, is created during the bitumen production process. The aim of this study was to investigate the use of this PFT tailings stream as a fuel source for combustion in a fluidized bed for energy recovery. To do so, physical and fluidization characteristics of the fuel as well as combustion kinetics were assessed through laboratory analysis. In addition, the fuel's combustion characteristics were investigated through experiments in a quartz wool matrix tubular reactor and theoretical calculations at various moisture contents. Results showed that this fuel can be burned in a fluidized bed with a reactivity comparable to that of coal samples. This research found that PFT tailings could be used to generate energy during disposal but further work will have to be undertaken in a hot CFB combustor to confirm this.

  10. Valorization of lignite combustion residues and ferroalumina in the production of aggregates.

    Science.gov (United States)

    Anagnostopoulos, I M; Stivanakis, V E; Angelopoulos, G N; Papamantellos, D C

    2010-02-15

    The present research study investigates the synergy of industrial solid by-products from lignite combustion (fly ash and bottom ash) and aluminum production (ferroalumina) in the production of lightweight aggregates (LWA). The process consists of two stages, pelletization and sintering. Bottom ash (BA) is used as the principal raw material in mixtures while ferroalumina (FAL) is added in lower percentages (5-30 wt%). BA carbon content is used as the fuel of sintering process in high temperatures, around 1250 degrees C, and gas generation is responsible for porous structure formation. Physical properties such as porosity, water absorption and bulk density, of sintering products are measured. Increase of FAL percentage in sintering mixtures results in decrease of porosity from 61% to 35% and of water absorption from 61% to 21% and in increase of bulk density from 1.02 g/cm(3) to 1.80 g/cm(3) of the produced aggregates. Aggregates produced by FAL addition up to 20 wt% are characterized as LWA. Aggregates formed are used in the production of concrete specimens. Compressive strength of concrete increases by increasing FAL addition in aggregates from 5 wt% to 15 wt% (highest strength value), while decrease by increasing FAL addition from 20 wt% to 30 wt%. FAL addition in lignite ashes sintering mixtures (up to 15 wt%) is considered as an important parameter for enhancing aggregates strength.

  11. Emission factors of polycyclic and nitro-polycyclic aromatic hydrocarbons from residential combustion of coal and crop residue pellets.

    Science.gov (United States)

    Yang, Xiaoyang; Liu, Shijie; Xu, Yisheng; Liu, Yu; Chen, Lijiang; Tang, Ning; Hayakawa, Kazuichi

    2017-12-01

    Polycyclic aromatic hydrocarbons (PAHs) and nitro-polycyclic aromatic hydrocarbons (NPAHs) are toxic pollutants mainly produced during fossil fuel combustion. Domestic coal stoves, which emit large amounts of PAHs and NPAHs, are widely used in the Chinese countryside. In this study, emission factors (Efs) for 13 PAH species and 21 NPAH species for four raw coal (three bituminous and one anthracite), one honeycomb briquette, and one crop residue pellet (peanut hulls) samples burned in a typical Chinese rural cooking stove were determined experimentally. The PAH and NPAH Efs for the six fuels were 3.15-49 mg/kg and 0.32-100 μg/kg, respectively. Peanut hulls had very high Efs for both PAHs and NPAHs, and honeycomb briquettes had the lowest Efs. 2-Nitropyrene and 2-nitrofluoranthene, which are NPAHs typically found in secondary organic aerosol, were detected in the emissions from some fuels, suggesting that chemical reactions may have occurred in the dilution tunnel between the flue gas leaving the stove and entering the sampler. The 1-nitropyrene to pyrene diagnostic ratios for coal and peanut hulls were 0.0001 ± 0.0001 and 0.0005, respectively. These were in the same order of magnitude as reference ratios for emissions during coal combustion. The 6-nitrobenzo[a]pyrene to benzo[a]pyrene ratios for the fuels were determined, and the ratios for coal and peanut hulls were 0.0010 ± 0.0001 and 0.0014, respectively. The calculated potential toxic risks indicated that peanut hull emissions were very toxic, especially in terms of NPAHs, compared with emissions from the other fuels. Copyright © 2017 Elsevier Ltd. All rights reserved.

  12. Thermal treatment system of hazardous residuals in three heating zones based on a microprocessor

    International Nuclear Information System (INIS)

    Luna H, C.L.

    1997-01-01

    Thermal treatment system consists of a high power electric oven of three heating zones where each zone works up to 1200 Centigrades; it has the capacity of rising the central zone temperature up to 1000 Centigrades in 58 minutes approximately. This configuration of three zones could be programmed to different temperatures and they will be digitally controlled by a control microprocessor, which has been controlled by its own assembler language, in function of the PID control. There are also other important controls based on this microprocessor, as a signal amplification, starting and shutdown of high power step relays, activation and deactivation of both analogic/digital and digital/analogic convertors, port activation and basic data storage of the system. Two main characteristics were looked for this oven design; the first was the possibility of controlling the three zone temperature and the second was to reduce the rising and stabilization operation time and its digitized control. The principal function of the three zone oven is to accelerate the degradation of hazardous residuals by an oxidation instead combustion, through relatively high temperatures (minimum 800 Centigrades and maximum 1200 Centigrades); this process reduces the ash and volatile particulate production. The hazardous residuals will be pumped into the degradation system and after atomized through a packaged column; this step will avoid the direct contact of the residuals with the oven cores. These features make this system as closed process, which means that the residuals can not leak to the working area, reducing the exposure risk to the personnel. This three step oven system is the first stage of the complete hazardous residuals degradation system; after this, the flow will go into a cold plasma region where the process is completed, making a closed system. (Author)

  13. Potentially toxic elements in lignite and its combustion residues from a power plant.

    Science.gov (United States)

    Ram, L C; Masto, R E; Srivastava, N K; George, J; Selvi, V A; Das, T B; Pal, S K; Maity, S; Mohanty, D

    2015-01-01

    The presence of potentially toxic elements in lignite and coal is a matter of global concern during energy extraction from them. Accordingly, Barsingsar lignite from Rajasthan (India), a newly identified and currently exploited commercial source of energy, was evaluated for the presence of these elements and their fate during its combustion. Mobility of these elements in Barsingsar lignite and its ashes from a power plant (Bikaner-Nagaur region of Thar Desert, India) is presented in this paper. Kaolinite, quartz, and gypsum are the main minerals in lignite. Both the fly ash and bottom ash of lignite belong to class-F with SiO₂ > Al₂O₃ > CaO > MgO. Both the ashes contain quartz, mullite, anhydrite, and albite. As, In, and Sr have higher concentration in the feed than the ashes. Compared to the feed lignite, Ba, Co, U, Cu, Cd, and Ni are enriched (10-5 times) in fly ash and Co, Pb, Li, Ga, Cd, and U in bottom ash (9-5 times). Earth crust-normalization pattern showed enrichment of Ga, U, B, Ag, Cd, and Se in the lignite; Li, Ba, Ga, B, Cu, Ag, Cd, Hg, Pb, and Se, in fly ash; and Li, Sr, Ga, U, B, Cu, Ag, Cd, Pb, and Se in bottom ash. Hg, Ag, Zn, Ni, Ba, and Se are possibly associated with pyrite. Leaching test by toxicity characteristic leaching procedure (TCLP) showed that except B all the elements are within the safe limits prescribed by Indian Standards.

  14. Treatment of plutonium process residues by molten salt oxidation

    International Nuclear Information System (INIS)

    Stimmel, J.; Wishau, R.; Ramsey, K.B.; Montoya, A.; Brock, J.; Heslop, M.

    1999-01-01

    Molten Salt Oxidation (MSO) is a thermal process that can remove more than 99.999% of the organic matrix from combustible 238 Pu material. Plutonium processing residues are injected into a molten salt bed with an excess of air. The salt (sodium carbonate) functions as a catalyst for the conversion of the organic material to carbon dioxide and water. Reactive species such as fluorine, chlorine, bromine, iodine, sulfur, phosphorous and arsenic in the organic waste react with the molten salt to form the corresponding neutralized salts, NaF, NaCl, NaBr, NaI, Na 2 SO 4 , Na 3 PO 4 and NaAsO 2 or Na 3 AsO4. Plutonium and other metals react with the molten salt and air to form metal salts or oxides. Saturated salt will be recycled and aqueous chemical separation will be used to recover the 238 Pu. The Los Alamos National Laboratory system, which is currently in the conceptual design stage, will be scaled down from current systems for use inside a glovebox

  15. Treatment of plutonium process residues by molten salt oxidation

    Energy Technology Data Exchange (ETDEWEB)

    Stimmel, J.; Wishau, R.; Ramsey, K.B.; Montoya, A.; Brock, J. [Los Alamos National Lab., NM (United States); Heslop, M. [Naval Surface Warfare Center (United States). Indian Head Div.; Wernly, K. [Molten Salt Oxidation Corp. (United States)

    1999-04-01

    Molten Salt Oxidation (MSO) is a thermal process that can remove more than 99.999% of the organic matrix from combustible {sup 238}Pu material. Plutonium processing residues are injected into a molten salt bed with an excess of air. The salt (sodium carbonate) functions as a catalyst for the conversion of the organic material to carbon dioxide and water. Reactive species such as fluorine, chlorine, bromine, iodine, sulfur, phosphorous and arsenic in the organic waste react with the molten salt to form the corresponding neutralized salts, NaF, NaCl, NaBr, NaI, Na{sub 2}SO{sub 4}, Na{sub 3}PO{sub 4} and NaAsO{sub 2} or Na{sub 3}AsO4. Plutonium and other metals react with the molten salt and air to form metal salts or oxides. Saturated salt will be recycled and aqueous chemical separation will be used to recover the {sup 238}Pu. The Los Alamos National Laboratory system, which is currently in the conceptual design stage, will be scaled down from current systems for use inside a glovebox.

  16. Comparison of NAA XRF and ICP-OES Methods on Analysis of Heavy Metals in Coals and Combustion Residues

    Directory of Open Access Journals (Sweden)

    Agus Taftazani

    2017-07-01

    Full Text Available Heavy metals in the samples of coals and combustion residues (bottom ash and fly ash from Pacitan coal-fired power plant (CPP have been identified by using NAA, XRF, and ICP-OES methods. This research was aimed to understand the analysis results correlation coefficient (R and determine the enrichment ratio (ER value of the samples by using three analysis methods. The results showed 10 elements have been simultaneously detected in all samples. The correlation coefficient of analysis results of metals content in coals by using NAA-XRF, XRF-ICP OES and with ICPOES-NAA methods gives R2£1 respectively. The correlation coefficient of analysis results of metals content in bottom ash and fly ash by using the methods of NAA-XRF, XRF-ICPOES, and ICPOES-NAA gained R2»1 respectively. ICP-OES method was most satisfactory in this study. The value of ER for identified metals by using the three methods in the samples of bottom ash and fly ash yielded the value over one, and ER value of fly ash was greater in comparison to the bottom ash.

  17. Chemical modifiers for direct determination of cobalt in coal combustion residues by ultrasonic slurry-sampling-ETAAS

    Energy Technology Data Exchange (ETDEWEB)

    Felipe-Sotelo, M.; Carlosena, A.; Fernandez, E.; Lopez-Mahia, P.; Muniategui, S.; Prada, D. [Dept. of Analytical Chemistry, Univ. of La Coruna (Spain)

    2001-12-01

    Five modifiers were tested for the direct determination of cobalt in coal fly ash and slag by ultrasonic slurry-sampling electrothermal atomic absorption spectrometry (USS-ETAAS).The furnace temperature programs and the appropriate amount for each modifier were optimized to get the highest signal and the best separation between the atomic and background signals. Nitric acid (0.5% v/v) was the most adequate chemical modifier for cobalt determination, selecting 1450 C and 2100 C as pyrolysis and atomization temperatures, respectively. This modifier also acts as liquid medium for the slurry simplifying the procedure. The remaining modifiers enhanced the background signal, totally overlapped with cobalt peak. The method optimized gave a limit of detection of 0.36 {mu}g g{sup -1}, a characteristic mass of 13{+-}1 pg and an overall-method precision which is highly satisfactory (<7%, RSD). The method was validated by analyzing two certified coal fly ash materials, and satisfactory recoveries were obtained (83-90%) and no statistical differences were observed between the experimental and the certified cobalt concentrations. Additionally, certified sediment, soil and urban particulate matter were assayed; again good results were obtained. The developed methodology was used to determine cobalt in several coal combustion residues from five Spanish power plants. (orig.)

  18. Estudio termodinámico de un motor de encendido por comprensión utilizando aceite residual de frituras como combustible alterno

    OpenAIRE

    Álvarez Basantes, Alex Marcelo; Álvarez Basantes, Carlos David; Montesdeoca Pichucho, Oscar Fabián

    2013-01-01

    El presente estudio consiste; en someter a un motor de encendido por compresión a otro tipo de combustible como es el aceite residual de frituras, realizando un análisis termodinámico a través de las temperaturas medidas en la admisión, el escape, el cabezote y la temperatura ambiente, además se muestra el análisis de gases obtenido al usar diesel comercial y aceite residual de frituras (ARF). The present study is, to submit to a compression ignition engine to another type of fuel and resi...

  19. Prediction of residual metabolic activity after treatment in NSCLC patients

    International Nuclear Information System (INIS)

    Rios Velazquez, Emmanuel; Aerts, Hugo J.W.L.; Oberije, Cary; Ruysscher, Dirk De; Lambin, Philippe

    2010-01-01

    Purpose. Metabolic response assessment is often used as a surrogate of local failure and survival. Early identification of patients with residual metabolic activity is essential as this enables selection of patients who could potentially benefit from additional therapy. We report on the development of a pre-treatment prediction model for metabolic response using patient, tumor and treatment factors. Methods. One hundred and one patients with inoperable NSCLC (stage I-IV), treated with 3D conformal radical (chemo)-radiotherapy were retrospectively included in this study. All patients received a pre and post-radiotherapy fluorodeoxyglucose positron emission tomography-computed tomography FDG-PET-CT scan. The electronic medical record system and the medical patient charts were reviewed to obtain demographic, clinical, tumor and treatment data. Primary outcome measure was examined using a metabolic response assessment on a post-radiotherapy FDG-PET-CT scan. Radiotherapy was delivered in fractions of 1.8 Gy, twice a day, with a median prescribed dose of 60 Gy. Results. Overall survival was worse in patients with residual metabolic active areas compared with the patients with a complete metabolic response (p=0.0001). In univariate analysis, three variables were significantly associated with residual disease: larger primary gross tumor volume (GTVprimary, p=0.002), higher pre-treatment maximum standardized uptake value (SUV max , p=0.0005) in the primary tumor and shorter overall treatment time (OTT, p=0.046). A multivariate model including GTVprimary, SUV max , equivalent radiation dose at 2 Gy corrected for time (EQD2, T) and OTT yielded an area under the curve assessed by the leave-one-out cross validation of 0.71 (95% CI, 0.65-0.76). Conclusion. Our results confirmed the validity of metabolic response assessment as a surrogate of survival. We developed a multivariate model that is able to identify patients at risk of residual disease. These patients may benefit from

  20. PRODUCCIÓN DE ELECTRICIDAD EN CELDAS DE COMBUSTIBLE MICROBIANAS UTILIZANDO AGUA RESIDUAL: EFECTO DE LA DISTANCIA ENTRE ELECTRODOS

    Directory of Open Access Journals (Sweden)

    Germán Buitrón

    2011-01-01

    Full Text Available Se evaluó la influencia de la separación de electrodos sobre la producción de electricidad y la eliminación de materia orgánica en celdas de combustible microbianas usando agua residual. Para ello se construyeron tres celdas de geometría semejante pero con diferente volumen. En promedio, se obtuvo una eficiencia de eliminación de materia orgánica del 71%. La duración del ciclo fue de 0.97 días para la celda de 40 mL, 1.03 días para la celda de 80 mL y 5.93 días para la celda de 120 mL. El aumento de distancia entre los electrodos (4, 8 y 12 cm no causó un efecto negativo en la generación de electricidad, pues en la mayor separación (celda de 120 mL se alcanzó un voltaje máximo de 660 mV, mientras que para las celdas de 40 y 80 mL fue de 540 mV y 532 mV, respectivamente. La densidad de potencia máxima se presentó en la celda con separación de 12 cm (408 mW/m2. Sin embargo, se observó que la potencia volumétrica disminuyó a medida que aumentó la separación entre los electrodos.

  1. Fabrication of a Spherical Titanium Powder by Combined Combustion Synthesis and DC Plasma Treatment

    Directory of Open Access Journals (Sweden)

    Choi S.H.

    2017-06-01

    Full Text Available Combustion synthesis is capable of producing many types of refractory and ceramic materials, as well as metals, with a relatively lower cost and shorter time frame than other solid state synthetic techniques. TiO2 with Mg as reductant were dry mixed and hand compacted into a 60 mm diameter mold and then combusted under an Ar atmosphere. Depending on the reaction parameters (Mg concentration 2 ≤ α ≤ 4, the thermocouples registered temperatures between 1160°C and 1710°C · 3 mol of Mg gave the optimum results with combustion temperature (Tc and combustion velocity (Uc values of 1372°C and 0.26 cm/s respectively. Furthermore, this ratio also had the lowest oxygen concentration in this study (0.8 wt%. After combustion, DC plasma treatment was carried out to spheroidize the Ti powder for use in 3D printing. The characterization of the final product was performed using X-ray diffraction, scanning electron microscopy, energy dispersive spectroscopy, and N/O analysis.

  2. Ractopamine Residues in Beef Cattle Hair During and After Treatment.

    Science.gov (United States)

    Liang, Xiaowei; Zhang, Kai; Zhang, Junmin; Li, Fadi; Zhao, Qingyu; Tang, Chaohua; Meng, Qingshi

    2016-03-01

    The objective of the present study was to assess the accumulation of ractopamine (RAC) residues in hair of Chinese Simmental beef cattle following exposure to two doses of RAC for 28 days. Six male cattle were orally administered with RAC hydrochloride at a dose of 0.67 mg/kg body weight/day (low-dose group, n = 3) and 2.01 mg/kg body weight/day (high-dose group, n = 3). The results suggested that RAC was obviously accumulated in hair, with a concentration of 5.57 ± 0.66 ng/g (white hair) and 13.67 ± 2.73 ng/g (red hair) in the low-dose group on Day 1 of treatment, respectively. In red hair, the peak concentrations of RAC were 5619.38 ± 2156.84 ng/g (low-dose group) and 6908.3 ± 1177.62 ng/g (high-dose group) on Day 14 of treatment, and then decreased slowly. In white hair, the highest concentrations of RAC were 3387.38 ± 1620.87 ng/g (low-dose group) on Day 14 of withdraw and 9621.72 ± 1497.65 ng/g (high-dose group) on Day 28 of treatment. The concentration of RAC in old hair was higher than that in new hair. No significant differences in RAC concentrations were obtained among dosage, hair color and old versus new hair (P > 0.05). The results indicated that ractopamine is significantly accumulated in red and white hair of Chinese Simmental beef cattle, which can be used as a matrix to assess the presence of RAC residues. © The Author 2015. Published by Oxford University Press. All rights reserved. For Permissions, please email: journals.permissions@oup.com.

  3. Accumulation of coal combustion residues and their immunological effects in the yellow-bellied slider (Trachemys scripta scripta).

    Science.gov (United States)

    Haskins, David L; Hamilton, Matthew T; Jones, Amanda L; Finger, John W; Bringolf, Robert B; Tuberville, Tracey D

    2017-05-01

    Anthropogenic activities such as industrial processes often produce copious amounts of contaminants that have the potential to negatively impact growth, survival, and reproduction of exposed wildlife. Coal combustion residues (CCRs) represent a major source of pollutants globally, resulting in the release of potentially harmful trace elements such as arsenic (As), cadmium (Cd), and selenium (Se) into the environment. In the United States, CCRs are typically stored in aquatic settling basins that may become attractive nuisances to wildlife. Trace element contaminants, such as CCRs, may pose a threat to biota yet little is known about their sublethal effects on reptiles. To assess the effects of CCR exposure in turtles, we sampled 81 yellow-bellied sliders (Trachemys scripta scripta) in 2014-2015 from CCR-contaminated and uncontaminated reference wetlands located on the Savannah River Site (Aiken, SC, USA). Specific aims were to (1) compare the accumulation of trace elements in T. s. scripta claw and blood samples between reference and CCR-contaminated site types, (2) evaluate potential immunological effects of CCRs via bacterial killing assays and phytohaemagglutinin (PHA) assays, and (3) quantify differences in hemogregarine parasite loads between site types. Claw As, Cd, copper (Cu), and Se (all p ≤ 0.001) and blood As, Cu, Se, and strontium (Sr; p ≤ 0.015) were significantly elevated in turtles from CCR-contaminated wetlands compared to turtles from reference wetlands. Turtles from reference wetlands exhibited lower bacterial killing (p = 0.015) abilities than individuals from contaminated sites but neither PHA responses (p = 0.566) nor parasite loads (p = 0.980) differed by site type. Despite relatively high CCR body burdens, sliders did not exhibit apparent impairment of immunological response or parasite load. In addition, the high correlation between claw and blood concentrations within individuals suggests that nonlethal tissue sampling may be

  4. The effect of low-NOx combustion on residual carbon in fly ash and its adsorption capacity for air entrainment admixtures in concrete

    DEFF Research Database (Denmark)

    Pedersen, Kim Hougaard; Jensen, Anker Degn; Dam-Johansen, Kim

    2010-01-01

    Fly ash from pulverized coal combustion contains residual carbon that can adsorb the air-entraining admixtures (AEAs) added to control the air entrainment in concrete. This is a problem that has increased by the implementation of low-NOx combustion technologies. In this work, pulverized fuel has...... by up to a factor of 25. This was due to a lower carbon content in the ash and a lower specific AEA adsorptivity of the carbon. The latter was suggested to be caused by changes in the adsorption properties of the unburned char and a decreased formation of soot, which was found to have a large AEA...... adsorption capacity based on measurements on a carbon black. The NOx formation increased by up to three times with more oxidizing conditions and thus, there was a trade-off between the AEA requirements of the ash and NOx formation. The type of fuel had high impact on the AEA adsorption behavior of the ash...

  5. Graphite fuels combustion off-gas treatment options

    International Nuclear Information System (INIS)

    Kirkham, R.J.; Lords, R.E.

    1993-03-01

    Scenarios for burning bulk graphite and for burning crushed fuel particles from graphite spent nuclear fuels have been considered. Particulates can be removed with sintered metal filters. Subsequent cooling would then condense semi-volatile fission products into or onto a particulate. These particulates would be trapped by a second sintered metal filter or downstream packed bed. A packed bed scrub column can be used to eliminate most of the iodine-129 and tritium. A molecular sieve bed is proposed to collect the residual 129 I and other tramp radionuclides downstream (Ruthenium, etc.). Krypton-85 can be recovered, if need be, either by cryogenics or by the KALC process (Krypton Adsorption in Liquid Carbon dioxide). Likewise carbon-14 in the form of carbon dioxide could be collected with a caustic or lime scrub solution and incorporated into a grout. Sulfur dioxide present will be well below regulatory concern level of 4.0 tons per year and most of it would be removed by the scrubber. Carbon monoxide emissions will depend on the choice of burner and start-up conditions. Should the system exceed the regulatory concern level, a catalytic converter in the final packed bed will be provided. Radon and its daughters have sufficiently short half-lives (less than two minutes). If necessary, an additional holdup bed can be added before the final HEPA filters or additional volume can be added to the molecular sieve bed to limit radon emissions. The calculated total effective dose equivalent at the Idaho National Engineering Laboratory boundary from a single release of all the 3 , 14 C, 85 Kr, and 129 I in the total fuel mass if 0.43 mrem/year

  6. Toxicity of solid residues resulting from wastewater treatment with nanomaterials.

    Science.gov (United States)

    Nogueira, Verónica; Lopes, Isabel; Rocha-Santos, Teresa; Gonçalves, Fernando; Pereira, Ruth

    2015-08-01

    Nanomaterials (NMs) are widely recommended for wastewater treatments due to their unique properties. Several studies report the different advantages of nanotechnology in the remediation of wastewaters, but limited research has been directed toward the fate and potential impacts of the solid residues (SRs) produced after the application of such technologies. The present work aimed at investigating the ecotoxicity of SRs resulting from the treatment of three effluents (OOMW, kraft pulp mill, and mining drainage) with two NMs (TiO2 and Fe2O3). The invertebrate Chironomus riparius was selected as test organism and exposed to the residues. The effect on percentage of survival and growth was assessed. Results showed that the SRs from the treatments nano-TiO2(1.0gL(-1))/H2O2(0.5M) and nano-Fe2O3(1.0gL(-1))/H2O2(1.0M) from OOMW and nano-Fe2O3(0.75gL(-1))/H2O2(0.01M) from kraft pulp mill effluent exhibited lethal toxicity to C. riparius. Only the exposure to SRs resulting from the treatment with nano-Fe2O3(0.75gL(-1))/H2O2(0.01M) applied to the kraft pulp mill effluent significantly affected the growth rate based on the head capsule width. In terms of growth rate, based on the body length, it decreased significantly after exposure to the SRs from the treatments nano-TiO2 (1.0gL(-1)) and nano-Fe2O3(0.75gL(-1))/H2O2(0.01M) of kraft paper mill effluent and nano-Fe2O3(1.0gL(-1))/H2O2(1.0M) of OOMW. According to our study the SRs can promote negative effects on C. riparius. However, the effects are dependent on the type of effluent treated as well as on the organic and inorganic compounds attached to the NMs. Copyright © 2015 Elsevier B.V. All rights reserved.

  7. Removal of coagulant aluminum from water treatment residuals by acid.

    Science.gov (United States)

    Okuda, Tetsuji; Nishijima, Wataru; Sugimoto, Mayo; Saka, Naoyuki; Nakai, Satoshi; Tanabe, Kazuyasu; Ito, Junki; Takenaka, Kenji; Okada, Mitsumasa

    2014-09-01

    Sediment sludge during coagulation and sedimentation in drinking water treatment is called "water treatment residuals (WTR)". Polyaluminum chloride (PAC) is mainly used as a coagulant in Japan. The recycling of WTR has been desired; one method for its reuse is as plowed soil. However, WTR reuse in this way is inhibited by the aluminum from the added PAC, because of its high adsorption capacity for phosphate and other fertilizer components. The removal of such aluminum from WTR would therefore be advantageous for its reuse as plowed soil; this research clarified the effect of acid washing on aluminum removal from WTR and on plant growth in the treated soil. The percentage of aluminum removal from raw WTR by sulphuric acid solution was around 90% at pH 3, the percentage decreasing to 40% in the case of a sun-dried sample. The maximum phosphate adsorption capacity was decreased and the available phosphorus was increased by acid washing, with 90% of aluminum removal. The enhancement of Japanese mustard spinach growth and the increased in plant uptake of phosphates following acid washing were observed. Copyright © 2014 Elsevier Ltd. All rights reserved.

  8. Co-Combustion of Fast Pyrolysis Bio-Oil Derived from Coffee Bean Residue and Diesel in an Oil-Fired Furnace

    Directory of Open Access Journals (Sweden)

    Shuhn-Shyurng Hou

    2017-10-01

    Full Text Available The combustion characteristics of co-firing bio-oil produced from the fast pyrolysis process of coffee bean residue and diesel in a 300-kWth oil-fired furnace are investigated. Using bio-oil to completely replace fossil fuels has limitations since bio-oil has undesirable properties, such as high water and oxygen contents, high viscosity, and low heating value. However, a low blend ratio of bio-oil used as a substitute for petroleum-derived oil has advantages; i.e., it can be easily combusted in existing furnaces without modifications. Thus, a promising solution is the partial substitution of diesel with bio-oil, rather than completely replacing it. A furnace test is performed for diesel alone and bio-oil/diesel blends with 5 vol % bio-oil. The results show that excellent stable combustion is observed during the co-firing test. Compared with diesel, with 5 vol % bio-oil content in the blends, both the wall temperature and gas temperature drop only slightly and exhibit similar furnace temperature distribution; meanwhile, comparable NO emissions (smaller than 57 ppm are obtained, and lower CO2 emissions are achieved because biomass is both carbon neutral and renewable. Moreover, SO2 and CO emissions under these two burning conditions are very low; SO2 and CO emissions are smaller than 6 and 35 ppm, respectively.

  9. An exploratory screening of organic substances in combustion residues; En orienterande screening av organiska aemnen i askor

    Energy Technology Data Exchange (ETDEWEB)

    Larsson, Lennart; Lind, Bo (Swedish Geotechnical Inst., Linkoeping (Sweden)); Bjurstroem, Henrik (AaF-Process, Stockholm (Sweden))

    2008-09-15

    Ash consists of the inorganic incombustible part of fuels, but it also always contains a small amount of organic matter, occurring as trace substances with concentrations in the order of mg/kg and lower. A few types of compounds are analysed comparatively frequently, e.g. PCDD/F (the so-called dioxins), but knowledge about the other organic substances is far from exhaustive. In this investigation, three ash samples have been subjected to a semi-quantitative GC/MS screening of semi-volatile substances. In this method of analysis the substances are extracted, separated in a gas chromatograph and identified as well as quantified using a mass spectrometer. Even if this type of analysis can be performed by researchers at universities, we chose to let commercial analytical laboratories do it in order to assess results from a nearly routine work. Residues from woody biofuels (recovered wood, virgin wood and bark) were chosen in order to complement the information that has previously been obtained on ash from municipal solid waste incineration. The GC/MS screening was carried out on both non-derivatised samples (non-polar compounds) and derivatised samples (polar compounds). The investigation aimed also at assessing the potential and the limitations of the screening method. In addition, the potentially hazardous properties of each identified substance were examined. Screening without and with derivatization is a cost-effective method to chart the content of semi-volatile organic substances. The results are relevant, but the method commercially available in Sweden is at present not mature enough for the use considered. It must be further developed before it can be included in e.g. regulatory texts. Limitations may be found in several steps of the method, principally: - Extraction and derivatisation, as the internal standard added is recovered only to a small extent for some ash samples, indicating that not everything has been found - Detection, i.e. both the sensitivity of

  10. Persistent free radicals, heavy metals and PAHs generated in particulate soot emissions and residue ash from controlled combustion of common types of plastic

    International Nuclear Information System (INIS)

    Valavanidis, Athanasios; Iliopoulos, Nikiforos; Gotsis, George; Fiotakis, Konstantinos

    2008-01-01

    The production and use of polymeric materials worldwide has reached levels of 150 million tonnes per year, and the majority of plastic materials are discarded in waste landfills where are burned generating toxic emissions. In the present study we conducted laboratory experiments for batch combustion/burning of commercial polymeric materials, simulating conditions of open fire combustion, with the purpose to analyze their emissions for chemical characteristics of toxicological importance. We used common types of plastic materials: poly(vinyl chloride) (PVC), low and high density poly(ethylene) (LDPE, HDPE), poly(styrene) (PS), poly(propylene) (PP) and poly(ethylene terephthalate) (PET). Samples of particulate smoke (soot) collected on filters and residue solid ash produced by controlled burning conditions at 600-750 deg. C are used for analysis. Emissions of particulate matter, persistent free radicals embedded in the carbonaceous polymeric matrix, heavy metals, other elements and PAHs were determined in both types of samples. Results showed that all plastics burned easily generating charred residue solid ash and black airborne particulate smoke. Persistent carbon- and oxygen-centered radicals, known for their toxic effects in inhalable airborne particles, were detected in both particulate smoke emissions and residue solid ash. Concentrations of heavy metals and other elements (determined by Inductively Coupled Plasma Emission Spectrometry, ICP, method) were measured in the airborne soot and residue ash. Toxic heavy metals, such as Pb, Zn, Cr, Ni, and Cd were relatively at were found at low concentrations. High concentrations were found for some lithophilic elements, such as Na, Ca, Mg, Si and Al in particulate soot and residue solid ash. Measurements of PAHs showed that low molecular weight PAHs were at higher concentrations in the airborne particulate soot than in the residue solid ash for all types of plastic. Higher-ringed PAHs were detected at higher

  11. Persistent free radicals, heavy metals and PAHs generated in particulate soot emissions and residue ash from controlled combustion of common types of plastic.

    Science.gov (United States)

    Valavanidis, Athanasios; Iliopoulos, Nikiforos; Gotsis, George; Fiotakis, Konstantinos

    2008-08-15

    The production and use of polymeric materials worldwide has reached levels of 150 million tonnes per year, and the majority of plastic materials are discarded in waste landfills where are burned generating toxic emissions. In the present study we conducted laboratory experiments for batch combustion/burning of commercial polymeric materials, simulating conditions of open fire combustion, with the purpose to analyze their emissions for chemical characteristics of toxicological importance. We used common types of plastic materials: poly(vinyl chloride) (PVC), low and high density poly(ethylene) (LDPE, HDPE), poly(styrene) (PS), poly(propylene) (PP) and poly(ethylene terephthalate) (PET). Samples of particulate smoke (soot) collected on filters and residue solid ash produced by controlled burning conditions at 600-750 degrees C are used for analysis. Emissions of particulate matter, persistent free radicals embedded in the carbonaceous polymeric matrix, heavy metals, other elements and PAHs were determined in both types of samples. Results showed that all plastics burned easily generating charred residue solid ash and black airborne particulate smoke. Persistent carbon- and oxygen-centered radicals, known for their toxic effects in inhalable airborne particles, were detected in both particulate smoke emissions and residue solid ash. Concentrations of heavy metals and other elements (determined by Inductively Coupled Plasma Emission Spectrometry, ICP, method) were measured in the airborne soot and residue ash. Toxic heavy metals, such as Pb, Zn, Cr, Ni, and Cd were relatively at were found at low concentrations. High concentrations were found for some lithophilic elements, such as Na, Ca, Mg, Si and Al in particulate soot and residue solid ash. Measurements of PAHs showed that low molecular weight PAHs were at higher concentrations in the airborne particulate soot than in the residue solid ash for all types of plastic. Higher-ringed PAHs were detected at higher

  12. Thermal treatment of stabilized air pollution control residues in a waste incinerator pilot plant. Part 1: Fate of elements and dioxins.

    Science.gov (United States)

    Bergfeldt, Brita; Jay, Klaus; Seifert, Helmuth; Vehlow, Jürgen; Christensen, Thomas H; Baun, Dorthe L; Mogensen, Erhardt P B

    2004-02-01

    Air pollution control (APC) residues from municipal solid waste incinerator plants that are treated by means of the Ferrox process can be more safely disposed of due to reduction of soluble salts and stabilization of heavy metals in an iron oxide matrix. Further stabilization can be obtained by thermal treatment inside a combustion chamber of a municipal solid waste incinerator. The influence of the Ferrox products on the combustion process, the quality of the residues, and the partitioning of heavy metals between the various solids and the gas have been investigated in the Karlsruhe TAM-ARA pilot plant for waste incineration. During the experiments only few parameters were influenced. An increase in the SO2 concentration in the raw gas and slightly lower temperatures in the fuel bed could be observed compared with reference tests. Higher contents of Fe and volatile heavy metals such as Zn, Cd, Pb and partly Hg in the Ferrox products lead to increased concentration of these elements in the solid residues of the co-feeding tests. Neither the burnout nor the PCDD/F formation was altered by the addition of the Ferrox products. Co-feeding of treated APC residues seems to be a feasible approach for obtaining a single solid residue from waste incineration.

  13. Adsorption of Roxarsone onto Drinking Water Treatment Residuals: Preliminary Studies

    Science.gov (United States)

    Salazar, J.; Sarkar, D.; Datta, R.; Sharma, S.

    2006-05-01

    Roxarsone (3-nitro-4-hydroxyphenyl-arsonic acid) is an organo-arsenical compound, commonly used as a feed additive in the broiler poultry industry to control coccidial intestinal parasites. Roxarsone is not toxic to the birds not only because of the low dose, and also because it most likely does not convert to toxic inorganic arsenic (As) in their systems. However, upon excretion, roxarsone may undergo transformation to inorganic As, posing a serious risk of contaminating the agricultural land and water bodies via surface runoff or leaching. The use of poultry litter as fertilizer results in As accumulation rates of up to 50 metric tons per year in agricultural lands. The immediate challenge, as identified by the various regulatory bodies in recent years is to develop an efficient, yet cost-effective and environmentally sound approach to cleaning up such As- contaminated soils. Recent studies conducted by our group have suggested that the drinking water treatment residuals (WTRs) can effectively retain As, thereby decreasing its mobility in the environment. The WTRs are byproducts of drinking water treatment processes and are typically composed of amorphous Fe/Al oxides, activated C and cationic polymers. They can be obtained free-of-cost from water treatment plants. It is well demonstrated that the environmental mobility of As is controlled by adsorption/desorption reactions onto mineral surfaces. Hence, knowledge of adsorption and desorption of As onto the WTRs is of environmental relevance. The reported study examined the adsorption and desorption characteristics of As using two types of WTRs, namely the Fe-WTRs (byproduct of Fe salt treatment), and the Al-WTRs (byproduct of Al salt treatment). All adsorption experiments were carried out in batch and As retention on the WTRs was investigated as a function of solid/solution ratio (1:5, 1:10, 1:25 and 1:50), equilibration time (10 min - 48 hr), pH (2 - 10) and initial As load (100, 500, 1000 and 2000 mg As/L). The

  14. Impact of Residual Fragments following Endourological Treatments in Renal Stones

    Directory of Open Access Journals (Sweden)

    Cenk Acar

    2012-01-01

    Full Text Available Today, shock wave lithotripsy (SWL, percutaneous nephrolithotomy (PCNL, and flexible ureterorenoscopy (URS are the most widely used modalities for the management of renal stones. In earlier series, treatment success of renal calculi assessed with KUB radiography, ultrasound, or intravenous pyelography which are less sensitive than CT that leads to be diversity of study results in reporting outcome. Residual fragments (RFs after interventional therapies may cause pain, infection, or obstruction. The size and location of RFs following SWL and PCNL are the major predictors for clinical significant symptoms and stone events requiring intervention. There is no consensus regarding schedule for followup of SWL, PCNL, and flexible URS. Active monitoring can be recommended when the stones become symptomatic, increase in size, or need intervention. RFs <4 mm after SWL and <2 mm after PCNL and flexible URS could be actively monitored on an annual basis with CT. Early repeat SWL and second-look endoscopy are recommended after primary SWL and PCNL, respectively. There is insufficient data for flexible URS, but RFs can be easily treated with repeat URS. Finally, medical therapy should be tailored based on the stone analysis and metabolic workup that may be helpful to prevent regrowth of the RFs.

  15. Treatment of residual waters of slaughterhouses with filters

    International Nuclear Information System (INIS)

    Ortiz A, Jesus Mario

    1995-01-01

    For studying the anaerobic treatment of the residual waters coming from a slaughterhouse of bovine livestock, they were used a system of two filters in series and a third unique filter as witness. With values average of load organic volumetric and time of retention of 1.6 kg/(m 3 d) and 26 hours respectively, the efficiencies of removal of total DQO were similar in the unique filter and in the system in series, of the order of 64% on the average. Likewise, the retention and accumulation of biological solids in the channel were shown as the main road of removal of the DQO. The differentiation of the process achieved with the two filters in series allowed establishing that most of the accumulation happened in the primary filter, as long as the fundamental of the bioconversion in methane took place in the secondary filter of the system in series. The first relative level of methanegenization obtained could be explained by the limitations to the activity of the methanogenic biomass imposed by the low temperatures, although it could not discard a probable inhibition for the hydrolysis products of the accumulated fats

  16. Combustion demonstration plant in circulant fluidized bed of residual coal; Planta de Demostracion de Combustion en Lecho Fluido Circulante de Carbones Residuales

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-12-31

    This report incorporates a summary of the operation results during the period of demonstration after started up. The report pretend to give an overview of the operation conditions along of the first year: Running hours, availability, electricity production, shooting downs, incidences, efficiency, fuel characteristics influence, pollutants emissions and standards comparations, etc. The main operation conclusions are: High availability, great number of running hours at full equivalent load; some months even over 100% regarding time scheduled. High reduction of gaseous emissions, really very low respecting the required by the applicable standards. It has been developed the engineering of a prototype project, by 30MW, using mixtures of solid fuels, residues and coals. (Author)

  17. Effects of Vermicompost and Water Treatment Residuals on Soil Physical Properties and Wheat Yield

    Science.gov (United States)

    Ibrahim, Mahmoud M.; Mahmoud, Essawy K.; Ibrahim, Doaa A.

    2015-04-01

    The application of vermicompost and water treatment residuals to improve the physical properties in the salt affected soils is a promising technology to meet the requirements of high plant growth and cost-effective reclamation. Therefore, the aim of this study was to investigate the effect of vermicompost and its mixtures with water treatment residuals on selected physical properties of saline sodic soil and on wheat yield. The treatments were vermicompost, water treatment residuals, vermicompost + water treatment residuals (1:1 and 2:1 wet weight ratio) at levels of 5 and 10 g dry weight kg-1 dry soil. The considered physical properties included aggregate stability, mean weight diameter, pore size distribution and dry bulk density. The addition of vermicompost and water treatment residuals had significant positive effects on the studied soil physical properties, and improved the grain yield of wheat. The treatment of (2 vermicompost + 1 water treatment residuals) at level of 5 g kg-1 soil gave the best grain yield. Combination of vermicompost and water treatment residuals improved the water treatment residuals efficiency in ameliorating the soil physical properties, and could be considered as an ameliorating material for the reclamation of salt affected soils.

  18. Greenhouse and laboratory study for the land application of water treatment residual

    OpenAIRE

    Lucas, Jay B.

    1991-01-01

    The disposal of water treatment residual has received little attention due to a lack of regulation, funding, and concern about their environmental impacts. Many treatment plants discharge alum residual directly into nearby water courses or dewater them for landfilling. If suitable land is available, land application of residual is cost effective and has the potential for negligible effects on the environment and may prove to be a long-term solution to the disposal problem. This...

  19. Effect of Solution Properties on Arsenic Adsorption by Drinking Water Treatment Residuals

    Science.gov (United States)

    Nagar, R.; Sarkar, D.; Datta, R.; Sharma, S.

    2005-05-01

    Arsenic (As) is a ubiquitous element in the environment. Higher levels of As in soils may result from various anthropogenic sources such as use of arsenical pesticides, fertilizers, wood preservatives, smelter wastes, and coal combustion. This is of great environmental and human health concern due to the high toxicity and proven carcinogenicity of several arsenical species. Thus there is a need for developing cost effective technologies capable of lowering bioavailable As concentrations in soils to environmentally acceptable levels. In-situ immobilization of metals using inexpensive amendments such as minerals (apatite, zeolite, or clay minerals) or waste by-products (steel shot, beringite, and iron-rich biosolids) to reduce bioavailability is an inexpensive alternative to the more expensive ex-situ remediation methods. One such emerging in-situ technique is the application of drinking water treatment residuals (WTRs). WTRs can be classified as a byproduct of drinking water treatment plants and are generally composed of amorphous Fe/Al oxides, activated C and cationic polymers. WTRs possess amorphous structure and generally have high positive charge. Because As is chemically similar to phosphorus, the oxyanions As (V) and As (III) may have the potential of being retained by the WTRs. Thus, it is hypothesized that WTRs retain As irreversibly, thereby reducing As biavailability. As mobility of arsenic is controlled by adsorption reactions, knowledge of adsorption of As by WTRs is of primary relevance. Although the overall rate of adsorption is dependent on numerous factors, review of the literature indicates that competing ions in solution play an important role in the overall retention of As; however, little work has been conducted to identify which ions provide the most competition. As arsenic adsorption appears to be influenced by the variable pH-dependent charges developed on the soil particle surfaces, the effect of pH is also of critical importance. Hence, the

  20. Drinking water treatment residuals: a review of recent uses.

    Science.gov (United States)

    Ippolito, J A; Barbarick, K A; Elliott, H A

    2011-01-01

    Coagulants such as alum [Al2(SO4)3 x 14H2O], FeCl3, or Fe2(SO4)3 are commonly used to remove particulate and dissolved constituents from water supplies in the production of drinking water. The resulting waste product, called water-treatment residuals (WTR), contains precipitated Al and Fe oxyhydroxides, resulting in a strong affinity for anionic species. Recent research has focused on using WTR as cost-effective materials to reduce soluble phosphorus (P) in soils, runoff, and land-applied organic wastes (manures and biosolids). Studies show P adsorption by WTR to be fast and nearly irreversible, suggesting long-term stable immobilization of WTR-bound P. Because excessive WTR application can induce P deficiency in crops, effective application rates and methods remain an area of intense research. Removal of other potential environmental contaminants [ClO4-, Se(+IV and +VI), As(+III and +V), and Hg] by WTR has been documented, suggesting potential use of WTR in environmental remediation. Although the creation of Al plant toxicity and enhanced Al leaching are concerns expressed by researchers, these effects are minimal at circumneutral soil pH conditions. Radioactivity, trace element levels, and enhanced Mn leaching have also been cited as potential problems in WTR usage as a soil supplement. However, these issues can be managed so as not to limit the beneficial use of WTR in controlling off-site P losses to sensitive water bodies or reducing soil-extractable P concentrations.

  1. Combined Treatment of Residual, Recurrent and Unresectable Gastric Cancer

    Energy Technology Data Exchange (ETDEWEB)

    Bae, Hoon Sik [Maryknoll Hospital, Pusan (Korea, Republic of)

    1990-06-15

    A series of 25 patients with residual, recurrent, and unresectable gastric cancer received various combination of surgery, radiotherapy (RT), chemotherapy (CT), and hyperthermia (HT). They were placed INTO 7 categories; 1) CT and HT-14 patients; 2) RT and HT-15 patients; 3) surgery, RT and HT-2 patients; 4) surgery, RT, HT and CT-1 patient; 5) RT, HT and CT-1 patient; 6) RT and CT-1 patient; 7) RT alone-1 patient. Three patients had curative resection. 21 patients received irradiation with tightly contoured portals to spare as much small bowel, kidney and marrow as possible. Hyperthermia was applied regionally once or twice a week for 23 patients using 8 MHz radiofrequency capacitive heating device (Thermotron RF-8). HT was given approximately 30 min after RT. 7 patients were treated with CT: 4 patients received HT and concomitant Mitomycin-C; 3 patients received HT and sequential 5-FU+Adriamycin+Mitomycin-C. There was not any treatment related deaths. There was also no evidence of treatment related problems with liver, kidney, stomach, or spinal cord except only one case of transient diabetic ketoacidosis. The tumor response was evaluable in 22 patients. None achieved complete remission. 11(50%) achieved partial remission. The response rate was correlated with total radiation dose and achieved maximum temperature. 9 of 14 (64%) received more than 4000 cGy showed partial remission; especially, all 3 patients received more than 5500 cGy achieved partial response. 8 of the 12 patients (67%) who achieved maximal temperature more than 41 .deg. C showed partial response in comparing with 25% (2 of 8 patients, below 41 .deg. C). The numbers of HT, however, was not correlated with the response. 3 of the 25 patients (12%) remain alive. The one who was surgically unresectable and underwent irradiation alone is in progression of the disease with distant metastases. The remaining two patients with curative resection are alive with free of disease, 24 and 35 months

  2. Combined Treatment of Residual, Recurrent and Unresectable Gastric Cancer

    International Nuclear Information System (INIS)

    Bae, Hoon Sik

    1990-01-01

    A series of 25 patients with residual, recurrent, and unresectable gastric cancer received various combination of surgery, radiotherapy (RT), chemotherapy (CT), and hyperthermia (HT). They were placed INTO 7 categories; 1) CT and HT-14 patients; 2) RT and HT-15 patients; 3) surgery, RT and HT-2 patients; 4) surgery, RT, HT and CT-1 patient; 5) RT, HT and CT-1 patient; 6) RT and CT-1 patient; 7) RT alone-1 patient. Three patients had curative resection. 21 patients received irradiation with tightly contoured portals to spare as much small bowel, kidney and marrow as possible. Hyperthermia was applied regionally once or twice a week for 23 patients using 8 MHz radiofrequency capacitive heating device (Thermotron RF-8). HT was given approximately 30 min after RT. 7 patients were treated with CT: 4 patients received HT and concomitant Mitomycin-C; 3 patients received HT and sequential 5-FU+Adriamycin+Mitomycin-C. There was not any treatment related deaths. There was also no evidence of treatment related problems with liver, kidney, stomach, or spinal cord except only one case of transient diabetic ketoacidosis. The tumor response was evaluable in 22 patients. None achieved complete remission. 11(50%) achieved partial remission. The response rate was correlated with total radiation dose and achieved maximum temperature. 9 of 14 (64%) received more than 4000 cGy showed partial remission; especially, all 3 patients received more than 5500 cGy achieved partial response. 8 of the 12 patients (67%) who achieved maximal temperature more than 41 .deg. C showed partial response in comparing with 25% (2 of 8 patients, below 41 .deg. C). The numbers of HT, however, was not correlated with the response. 3 of the 25 patients (12%) remain alive. The one who was surgically unresectable and underwent irradiation alone is in progression of the disease with distant metastases. The remaining two patients with curative resection are alive with free of disease, 24 and 35 months

  3. Combustion testing and heat recovery study: Frank E. Van Lare Wastewater Treatment Plant, Monroe County. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Chattopadhyay, A.

    1995-01-01

    The report describes the results of combustion testing work, and analysis of heat recovery and use at the Monroe County Frank E. Van Lare wastwater treatment plant (WWTP). The three multiple-hearth furnaces at the plant process an average of 65 dry tons of dewatered sludge per day. The furnaces use about 12.5 million Btus of natural gas per dry ton of sludge incinerated, or about 300 billion Btus per year. Center shaft and rabble arm cooling air is recirculated to the furnaces as pre-heated combustion air. No other heat from the combustion process is recovered for use in the plant. The project had four objectives: to record and analyze sludge management operations data and sludge incinerator combustion data; to ascertain instrumentation and control needs; to calculate heat balances for the incineration system; and to determine the feasibility of full waste-heat recovery and utilization, at the Frank E. Van Lare wastewater treatment plant.

  4. Guidance for classification of residues from combustion and incineration in accordance with the Swedish ordinance for waste; Vaegledning foer klassificering av foerbraenningsrester enligt Avfallsfoerordningen

    Energy Technology Data Exchange (ETDEWEB)

    Adler, Peter [AaF Energi och Miljoe AB, Stockholm (Sweden); Haglund, Jan-Erik [Soederenergi AB, Stockholm (Sweden); Sjoeblom, Rolf [Tekedo AB, Nykoeping (Sweden)

    2004-05-01

    A new ordinance for waste came into force in Sweden on the first of January 2002, replacing some previous ordinances. The new ordinance is based on certain EU directives and contains amongst other things new rules regarding how certain streams of waste are to be classified into hazardous waste and non-hazardous waste. In a number of cases, the classification is to be made according to whether or not the waste possesses one or more of a number o properties H1 - H14, i e if the waste contains hazardous substances. The new rules are based on the regulation that exists for chemical substances and preparations. When attempts have been made to use these new rules in practice - e g for residues from incineration and combustion - it has become apparent that they are very difficult or even impossible to apply. The primary reason for this is that the residues contain a very large number (thousands) of substances which would have to be analysed and for which the hazard would have to be assessed correctly in accordance with the criteria for the properties (H4 - H8 and H10 - H11). Furthermore, some of the properties listed in the ordinance for waste lack criteria for assessment of hazard. These are H13 (can give rise to another substance which may be hazardous, e g leachate) and H14 (hazardous to the environment). Moreover, there are significant differences between the Ordinance of waste and the regulation of the National Chemicals Inspectorate. It is on the latter that the rules in the Ordinance of waste are based, and this is also the cause of many of the questions and of the uncertainties in the classification. In the present report, a method is developed and described for classification of residues from combustion and incineration. The method is to be applicable in practice without compromising environmental and health aspects. As a part of the present work, a compilation of content and alteration of chemical substances in is carried out. In another chapter, the experience

  5. Field Measurements of Trace Gases and Aerosols Emitted by Undersampled Combustion Sources Including Wood and Dung Cooking Fires, Garbage and Crop Residue Burning, and Indonesian Peat Fires

    Science.gov (United States)

    Stockwell, C.; Jayarathne, T. S.; Goetz, D.; Simpson, I. J.; Selimovic, V.; Bhave, P.; Blake, D. R.; Cochrane, M. A.; Ryan, K. C.; Putra, E. I.; Saharjo, B.; Stone, E. A.; DeCarlo, P. F.; Yokelson, R. J.

    2017-12-01

    Field measurements were conducted in Nepal and in the Indonesian province of Central Kalimantan to improve characterization of trace gases and aerosols emitted by undersampled combustion sources. The sources targeted included cooking with a variety of stoves, garbage burning, crop residue burning, and authentic peat fires. Trace gas and aerosol emissions were studied using a land-based Fourier transform infrared spectrometer, whole air sampling, photoacoustic extinctiometers (405 and 870nm), and filter samples that were analyzed off-line. These measurements were used to calculate fuel-based emission factors (EFs) for up to 90 gases, PM2.5, and PM2.5 constituents. The aerosol optical data measured included EFs for the scattering and absorption coefficients, the single scattering albedo (at 870 and 405 nm), as well as the absorption Ångström exponent. The emissions varied significantly by source, although light absorption by both brown and black carbon (BrC and BC, respectively) was important for all non-peat sources. For authentic peat combustion, the emissions of BC were negligible and absorption was dominated by organic aerosol. The field results from peat burning were in reasonable agreement with recent lab measurements of smoldering Kalimantan peat and compare well to the limited data available from other field studies. The EFs can be used with estimates of fuel consumption to improve regional emissions inventories and assessments of the climate and health impacts of these undersampled sources.

  6. Spatial distribution of polycyclic aromatic hydrocarbons in soil, sediment, and combusted residue at an e-waste processing site in southeast China.

    Science.gov (United States)

    Leung, Anna O W; Cheung, Kwai Chung; Wong, Ming Hung

    2015-06-01

    The environmental pollution and health impacts caused by the primitive and crude recycling of e-waste have become urgent global issues. Guiyu, China is a major hotspot of e-waste recycling. In this study, the levels and distribution of polycyclic aromatic hydrocarbons in soil in Guiyu were determined to investigate the effect of e-waste activities on the environment and to identify possible sources of these pollutants. Sediment samples from a local duck pond, water gullies, a river tributary, and combusted residue from e-waste burning sites were also investigated. The general trend found in soil (Σ16 PAHs) was acid leaching site > duck pond > rice field > printer roller dump site > reservoir (control site) and ranged from 95.2 ± 54.2 to 5,210 ± 89.6 ng/g (dry wt). The highest average total PAH concentrations were found in combusted residues of wires, cables, and other computer electrical components located at two e-waste open burning sites (18,600 and 10,800 ± 3,940 ng/g). These were 195- and 113-fold higher than the PAH concentrations of soil at the control site. Sediment PAH concentrations ranged from 37.2 ± 6 to 534 ± 271 ng/g. Results of this study provide further evidence of significant input of PAHs to the environment attributed to crude e-waste recycling.

  7. Residual stress development and relief in high strength aluminium alloys using standard and retrogression thermal treatments

    OpenAIRE

    Robinson, J.S; Tanner, D.A

    2003-01-01

    peer-reviewed Residual stresses develop in the aluminium alloy 7010 when the material is quenched from the solution heat treatment temperature. Residual stress measurements have been made using the X-ray diffraction technique and a longitudinal split sawcut method to determine the magnitude of residual stress that develops in specimens sectioned from large open die forgings as a result of (a) quenching these specimens into water at different temperatures, and (b) cold water quenching from ...

  8. Elemental analysis of ash residue from combustion of CCA treated wood waste before and after electrodialytic extraction

    DEFF Research Database (Denmark)

    Pedersen, Anne Juul; Ottosen, Lisbeth M.

    2006-01-01

    . Chemical analyses of untreated and treated ash confirmed that most As, but only smaller amounts of Cu and Cr was removed due to the electrodialytic extraction. Overall metal contents in the original ash residue were: 1.4 g As, 2.76 g Cu and 2.48 g Cr, after electrodialytic extraction these amounts were...

  9. Review on the Influences of Bagging Treatment on Pesticide Residue in Fruits

    Directory of Open Access Journals (Sweden)

    ZHAO Xiao-yun

    2018-02-01

    Full Text Available At present, bagging technology has been widely applicated in fruit cultivation. Impact of bagging treatment on the pesticide residues have different results. On the basis of existing achievements, this paper systematically analyzed the influence of different bagging treatments on pesticide residues:such as different ways of applying pesticide, pesticide concentration, number of applying pesticide; bagging materials, bagged layer; the type of pesticide(systemic pesticide, nonendoscopic pesticide; different portions of the fruit, crop varieties and so on. The way of applying pesticide had great impact on pesticide residue, pesticide application after bagging could largely reduce the pesticide residue, and pesticide application before bagging could increase pesticide residues; The four factors including pesticide appliacation dosage, the type of pesticides and fruit portion and fruit varieties on the effects of pesticide residues, had interaction each other. The pesticide applying several times, bagging could significantly reduce pesticide residues and control within the security level. Different bagging materials could reduce pesticide residues, but the impact on pesticide residues had no significant difference. More bagging layers caused less pesticide residues.

  10. Water Vapor Adsorption on Biomass Based Carbons under Post-Combustion CO2 Capture Conditions: Effect of Post-Treatment

    Science.gov (United States)

    Querejeta, Nausika; Plaza, Marta G.; Rubiera, Fernando; Pevida, Covadonga

    2016-01-01

    The effect of post-treatment upon the H2O adsorption performance of biomass-based carbons was studied under post-combustion CO2 capture conditions. Oxygen surface functionalities were partially replaced through heat treatment, acid washing, and wet impregnation with amines. The surface chemistry of the final carbon is strongly affected by the type of post-treatment: acid treatment introduces a greater amount of oxygen whereas it is substantially reduced after thermal treatment. The porous texture of the carbons is also influenced by post-treatment: the wider pore volume is somewhat reduced, while narrow microporosity remains unaltered only after acid treatment. Despite heat treatment leading to a reduction in the number of oxygen surface groups, water vapor adsorption was enhanced in the higher pressure range. On the other hand acid treatment and wet impregnation with amines reduce the total water vapor uptake thus being more suitable for post-combustion CO2 capture applications. PMID:28773488

  11. Water Vapor Adsorption on Biomass Based Carbons under Post-Combustion CO2 Capture Conditions: Effect of Post-Treatment

    Directory of Open Access Journals (Sweden)

    Nausika Querejeta

    2016-05-01

    Full Text Available The effect of post-treatment upon the H2O adsorption performance of biomass-based carbons was studied under post-combustion CO2 capture conditions. Oxygen surface functionalities were partially replaced through heat treatment, acid washing, and wet impregnation with amines. The surface chemistry of the final carbon is strongly affected by the type of post-treatment: acid treatment introduces a greater amount of oxygen whereas it is substantially reduced after thermal treatment. The porous texture of the carbons is also influenced by post-treatment: the wider pore volume is somewhat reduced, while narrow microporosity remains unaltered only after acid treatment. Despite heat treatment leading to a reduction in the number of oxygen surface groups, water vapor adsorption was enhanced in the higher pressure range. On the other hand acid treatment and wet impregnation with amines reduce the total water vapor uptake thus being more suitable for post-combustion CO2 capture applications.

  12. Kinetics of gasification and combustion of residues, biomass and coal in a bubbling fluidized bed; Die Kinetik der Vergasung und Verbrennung unterschiedlicher Abfaelle, Biomassen und Kohlen in der blasenbildenden Wirbelschicht

    Energy Technology Data Exchange (ETDEWEB)

    Hamel, S.; Krumm, W. [Siegen Univ. (Gesamthochschule) (Germany). Lehrstuhl fuer Energie- und Umweltverfahrenstechnik

    1998-09-01

    The combustion and gasification characteristics of Rhenish brown coal, domestic waste, waste plastics, wood and sewage sludge were investigated in a bubbling atmospheric fluidized bed in the laboratory scale. The materials were pyrolyzed in the fluidized bed in a nitrogen atmosphere. The residual coke was combuted in the presence of oxygen with varying operating parameters or else gasified in the presence of carbon dioxide. The different materials were characterized by global combustion rates, and kinetic parameters were determined for residual coke combustion. (orig.) [Deutsch] Das Verbrennungs- und Vergasungsverhalten von Rheinischer Braunkohle, Hausmuell, Restkunststoff, Holz und Klaerschlamm wurde in einer blasenbildenden, atmosphaerischen Laborwirbelschicht untersucht. Die Einsatzstoffe wurden in der mit Stickstoff fluidisierten Wirbelschicht pyrolysiert. Der verbleibende Restkoks wurde anschliessend unter Variation der Betriebsparameter mit Sauerstoff verbrannt oder mit Kohlendioxid vergast. Die unterschiedlichen Einsatzstoffe wurden durch globale Vebrennungsraten charakterisiert. Fuer die Restkoksverbrennung wurden kinetische Parameter ermittelt. (orig.)

  13. Forest treatment residues for thermal energy compared with disposal by onsite burning: Emissions and energy return

    Science.gov (United States)

    Greg Jones; Dan Loeffler; David Calkin; Woodam Chung

    2010-01-01

    Mill residues from forest industries are the source for most of the current wood-based energy in the US, approximately 2.1% of the nation's energy use in 2007. Forest residues from silvicultural treatments, which include limbs, tops, and small non-commercial trees removed for various forest management objectives, represent an additional source of woody biomass for...

  14. Residuals, bioaccessibility and health risk assessment of PAHs in winter wheat grains from areas influenced by coal combustion in China.

    Science.gov (United States)

    Tian, Kai; Bao, Huanyu; Zhang, Xuechen; Shi, Taoran; Liu, Xueping; Wu, Fuyong

    2018-03-15

    Polycyclic aromatic hydrocarbons (PAHs) contamination in atmospheric and soil was serious, which is mainly due to high level of emission of PAHs in China resulted from the predominating use of coal in energy consumption and continuous development of economy and society for years. However, the status of PAHs in winter wheat grains from the areas influenced by coal combustion in China was still not clear. During harvest season, the winter wheat grains were collected from agricultural fields surrounding coal-fired power plants located in Shaanxi and Henan Provinces. This study found that the mean concentrations of 15 priority PAHs ranged from 69.58 to 557.0μgkg -1 . Three-ring PAHs (acenaphthene, acenaphthylene, fluorene, phenanthrene and anthracene) were dominant in the grains, accounting for approximately 70-81% of the total PAHs. The bioaccessibility of low molecular weight (LMW, 2-3 ring) PAHs (51.1-52.8%), high molecular weight (HMW, 4-6 ring) PAHs (19.8-27.6%) and total PAHs (40.9-48.0%) in the intestinal condition was significantly (pvalues of incremental lifetime cancer risk (ILCR) for children, adolescents, adults and seniors were all higher than the baseline value (10 -6 ) and some even fell in the range of 10 -5 -10 -4 , which indicated that most grains from the areas affected by coal combustion possessed considerable cancer risk. The present study also indicated that the children were the age group most sensitive to PAHs contamination. The pilot research provided relevant information for the regulation of PAHs in the winter wheat grains and for the safety of the agro-products growing in the PAHs-contaminated areas. Copyright © 2017 Elsevier B.V. All rights reserved.

  15. Effects of alternate fuels. Report No. 2. Analysis of basic refractories degraded by residual oil combustion products

    Energy Technology Data Exchange (ETDEWEB)

    Wei, G. C.; Tennery, V. J.

    1978-02-01

    Industrial conversion in the U.S. to alternate fuels from natural gas is presently under way and will accelerate rapidly as a result of gas curtailments and National policy considerations. Currently the prime alternate fuels are distillate and residual oils and coal. Conversion to residual oils or coal for high-temperature process heat applications is anticipated to result in accelerated refractory and insulation corrosion and degradation due to reactions between fuel impurities and the ceramic linings of high-temperature equipment. Understanding the nature of such reactions and identification of means for preventing or retarding them will be of considerable assistance to both refractory manufacturers and users as well as a significant contribution to energy conservation.

  16. Review on the Influences of Bagging Treatment on Pesticide Residue in Fruits

    OpenAIRE

    ZHAO Xiao-yun; XIE De-fang

    2018-01-01

    At present, bagging technology has been widely applicated in fruit cultivation. Impact of bagging treatment on the pesticide residues have different results. On the basis of existing achievements, this paper systematically analyzed the influence of different bagging treatments on pesticide residues:such as different ways of applying pesticide, pesticide concentration, number of applying pesticide; bagging materials, bagged layer; the type of pesticide(systemic pesticide, nonendoscopic pestici...

  17. Lightweight combustion residues-based structural materials for use in mines. Quarterly report, 1 December 1994--28 February 1995

    Energy Technology Data Exchange (ETDEWEB)

    Chugh, Yoginder P.; Zhang, Yuzhuo; Ghosh, A.K.; Palmer, S.R; Peng, Suping, Xiao, Y. [Southern Illinois Univ., Carbondale, IL (United States)

    1995-12-31

    The overall goal of this project is to develop, design and test artificial supports (post and crib members) for use in mines manufactured from coal combustion by-product (CCB) based lightweight structural materials. The lightweight cement-fly ash grout with density ranging from 70 to 110 pcf has been developed incorporating very high volume (50--60 % of whole solid materials) fly ash. Characterization of individual component materials for the CCB-based structural materials has been performed for Class F fly ash, ASTM Type I cement, lime, silica fume, polypropylene fibers, protein-based foam, water-reducing agents, and calcium chloride. During the past quarter, we emphasized on screening mix designs and establishing mixing and curing procedures. We have demonstrated for the first time that cellular cement-fly ash grout can be developed with very low water: cement ratio (0.32--0.45). After forming, all the samples in the molds were moist cured in a chamber for 24-hours, at 90% relatively humidity (RH) and at 72{degrees}F. They were then demolded and transferred to a low pressure steam chamber (150{degrees}F and 100% RH). After steaming for 24 hours the samples were removed to a moist cure chamber prior to testing.

  18. Efficiency of Livestock Residue Treatment in Geomembrane Digesters

    Directory of Open Access Journals (Sweden)

    Yanet Pérez González

    2017-09-01

    Full Text Available The efficiency of twelve 10 m3 geomembrane biodigesters to treat swine and cattle residuals was assessed. The study took place at the Cooperative of Credits and Services (CCS of the municipality of Cumanayagua, Cienfuegos, Cuba. Its goal was to evaluate feasibility of technology implementation in Cuba. The effluent physical and chemical indicators were determined at entry and exit from biodigesters. The biodigesters charged with pig manure were able to remove 75.88% COD, and up to 66-44% SS. Besides, 64.79% of the contaminating organic load was converted into volatile products during biofermentation. Meanwhile, the biodigesters charged with cattle manure removed 60.42% of COD, and up to 67.67% of SS; 61.51% of the organic contaminating load was converted in volatile products. It was concluded that the biodigesters had acceptable efficiency values, and that the technology can be applied in Cuba.

  19. [Treatment of residual obstetrical brachial plexus palsy with tendon transfer].

    Science.gov (United States)

    Demirhan, Mehmet; Erdem, Mehmet; Uysal, Mustafa

    2002-01-01

    We evaluated the results of the correction of adduction and internal rotation deformities of the shoulder associated with residual obstetrical brachial plexus palsy (OBPP) by the transfer of latissimus dorsi and teres major muscles to the rotator cuff. In order to correct adduction and internal rotation deformities associated with residual OBPP, 10 patients (7 males, 3 females; mean age 8.1 years; range 4 to 19 years) underwent transfer of the latissimus dorsi and teres major muscles to the rotator cuff and lengthening of the pectoralis major tendon with Z-plasty. The right and left extremities were affected in seven and three patients, respectively. Involvement of the C5-C6 nerve roots was detected in four, and C5-C6-C7 nerve roots in six patients. In two patients with a positive Putti sign, axillary roentgenograms showed posterior subluxation of the humeral head, and magnetic resonance and computed tomography scans revealed type III glenohumeral deformity. Functional evaluations were made using a 5-point scoring system proposed by Mallet. The mean follow-up was 23.6 months (range 5 to 42 months). Postoperatively, the mean abduction and external rotation were 134.5 degrees (range 95 degrees to 170 degrees ) and 70 degrees (range 45 degrees to 90 degrees ), respectively. The mean global abduction score was 4, external rotation score was 4.2, and the scores assigned to the ability to move hand to the neck and mouth were 3.5. Of two patients with type III glenohumeral deformity, whose ages were four and 19 years, abduction and external rotation were 150 degrees and 45 degrees in the former, 135 degrees and 70 degrees in the latter, respectively. The transfer of the latissimus dorsi and teres major tendons is a necessary procedure to restore external rotation and abduction functions of paralysed shoulders. Compared to other techniques employed, it offers obvious advantages in terms of ease and cost, as well.

  20. Gasification and combustion technologies of agro-residues and their application to rural electric power systems in India

    Science.gov (United States)

    Bharadwaj, Anshu

    Biomass based power generation has the potential to add up to 20,000 MW of distributed capacity in India close to the rural load centers. However, the present production of biomass-based electricity is modest, contributing a mere 300 MW of installed capacity. In this thesis, we shall examine some of the scientific, technological and policy issues concerned with the generation and commercial viability of biomass-based electric power. We first consider the present status of biomass-based power in India and make an attempt to understand the reasons for low utilization. Our analysis suggests that the small-scale biomass power plants (rice or sugar mills where power plants of capacities in excess of 5 MW are possible without biomass transportation. We then simulate a biomass gasification combustion cycle using a naturally aspirated spark ignition engine since it can run totally on biomass gas. The gasifier and engine are modeled using the chemical equilibrium approach. The simulation is used to study the impact of fuel moisture and the performance of different biomass feedstock. Biomass power plants when used for decentralized power generation; close to the rural load centers can solve some of the problems of rural power supply: provide voltage support, reactive power and peak shaving. We consider an innovative option of setting up a rural electricity micro-grid using a decentralized biomass power plant and selected a rural feeder in Tumkur district, Karnataka for three-phase AC load flow studies. Our results suggest that this option significantly reduces the distribution losses and improves the voltage profiles. We examine a few innovative policy options for making a rural micro-grid economically viable and also a pricing mechanism for reactive power and wheeling. We next consider co-firing biomass and coal in utility boilers as an attractive option for biomass utilization because of low capital costs; high efficiency of utility boilers; lower CO2 emissions (per k

  1. Thermal treatment of solid residues from WtE units: A review

    International Nuclear Information System (INIS)

    Lindberg, Daniel; Molin, Camilla; Hupa, Mikko

    2015-01-01

    Highlights: • We review the thermal treatment methods for ashes and residues from WtE plants. • We review the results from extensive laboratory work on vitrification, melting and vaporization of ash. • We analyze the results from the extensive patent literature on thermal treatment. • We review industrial concepts for thermal treatment of ash. - Abstract: Thermal treatment methods of bottom ash, fly ash and various types of APC (air pollution control) residues from waste-to-energy plants can be used to obtain environmentally stable material. The thermal treatment processes are meant to reduce the leachability of harmful residue constituents, destroy toxic organic compounds, reduce residue volume, and produce material suitable for utilization. Fly ash and APC residues often have high levels of soluble salts, particularly chlorides, metals such as cadmium, lead, copper and zinc, and trace levels of organic pollutants such as dioxins and furans. Different thermal treatment methods can be used to either decompose or stabilize harmful elements and compounds in the ash, or separate them from the ash to get a material that can be safely stored or used as products or raw materials. In the present paper, thermal treatment methods, such as sintering, vitrification, and melting have been reviewed. In addition to a review of the scientific literature, a survey has been made of the extensive patent literature in the field

  2. Thermal treatment of solid residues from WtE units: A review

    Energy Technology Data Exchange (ETDEWEB)

    Lindberg, Daniel, E-mail: daniel.lindberg@abo.fi; Molin, Camilla, E-mail: camilla.molin@abo.fi; Hupa, Mikko, E-mail: mikko.hupa@abo.fi

    2015-03-15

    Highlights: • We review the thermal treatment methods for ashes and residues from WtE plants. • We review the results from extensive laboratory work on vitrification, melting and vaporization of ash. • We analyze the results from the extensive patent literature on thermal treatment. • We review industrial concepts for thermal treatment of ash. - Abstract: Thermal treatment methods of bottom ash, fly ash and various types of APC (air pollution control) residues from waste-to-energy plants can be used to obtain environmentally stable material. The thermal treatment processes are meant to reduce the leachability of harmful residue constituents, destroy toxic organic compounds, reduce residue volume, and produce material suitable for utilization. Fly ash and APC residues often have high levels of soluble salts, particularly chlorides, metals such as cadmium, lead, copper and zinc, and trace levels of organic pollutants such as dioxins and furans. Different thermal treatment methods can be used to either decompose or stabilize harmful elements and compounds in the ash, or separate them from the ash to get a material that can be safely stored or used as products or raw materials. In the present paper, thermal treatment methods, such as sintering, vitrification, and melting have been reviewed. In addition to a review of the scientific literature, a survey has been made of the extensive patent literature in the field.

  3. Effects of Cryogenic Treatment on Residual Stress and Tensile Properties for 6061 Al Alloy

    International Nuclear Information System (INIS)

    Park, Kijung; Cho, Young-Rae; Ko, Dea Hoon; Kim, Byung Min; Lim, Hak Jin; Lee, Jung Min

    2011-01-01

    To develop a 6061 aluminum alloy with low residual stress and high tensile strength, a cryogenic treatment process was investigated. Compared to the conventional heat treatment process for precipitation hardening with artificial aging, the cryogenic treatment process has two additional steps. The first step is cryogenic quenching of the sample into liquid nitrogen, the second step is up-hill quenching of the sample into boiling water. The residual stress for the sample was measured by the sin 2 ψ method with X-ray diffraction. The 6061 aluminum alloy sample showed 67% relief in stress at the cryogenic treatment process with artificial aging at 175°C. From this study, it was found that the optimum cryogenic treatment process for a sample with low residual stress and high tensile strength is relatively low cooling speed in the cryogenic quenching step and a very high heating speed in the up-hill quenching step.

  4. Processes subject to integrated pollution control. Combustion processes: reheat and heat treatment furnaces 50 MW(th) and over

    International Nuclear Information System (INIS)

    1995-01-01

    This document, part of a series offering guidance on pollution control regulations issued by Her Majesty's Inspectorate of Pollution, focuses on combustion processes involved with reheat and heat treatment furnaces of 50 MW (th) and over. Techniques for controlling releases into air, water and to land are detailed as are the various pollution monitoring strategies. (UK)

  5. Environmental Accounting Evidence in Organic Solid Residue Treatment Companies

    Directory of Open Access Journals (Sweden)

    Bruna Batista Padilha

    2014-06-01

    Full Text Available The growing concern with natural resources and the environment brings out the true dimension of these issues. The awareness of society causes companies to adopt environmentally correct policies and attitudes, so as to contribute with the preservation of the environment. Accounting, as a social science which studies the patrimony and its affectations, has adapted to the need of its users and has started to care about proper presentation and measurement of environmental items, for effective publication to society. With this premise, this study aims to identify and describe the contributions of Environmental Accounting to the process of environmental accounting disclosure of a company, which deals with organic solid residues from agriculture. Using a case study, it has been intended to analyze the production process and to list the environmental items and events that could benefit the company through their disclosure. It was intended, with this study, to highlight the contribution that the environmental accounting may add to the company, with proper measurement and presentation proposals. We have been able to verify that, indeed, there are events of an environmental nature resulting from the production process and also of the investment that it carries out periodically to preserve nature; however, there re faults in the accounting records from an environmental point of view. The application of environmental accounting in the organization allows for a broad view of environmental management and sustainable development adopted by the entity, registering all events that may generate economic and financial changes.

  6. The effect of sludge water treatment plant residuals on the properties of compressed brick

    Science.gov (United States)

    Shamsudin, Shamrul-Mar; Shahidan, S.; Azmi, M. A. M.; Ghaffar, S. A.; Ghani, M. B. Abdul; Saiful Bahari, N. A. A.; Zuki, S. S. M.

    2017-11-01

    The focus of this study is on the production of compressed bricks which contains sludge water treatment plant (SWTP) residuals obtained from SAJ. The main objective of this study is to utilise and incorporate discarded material (SWTP) in the form of residual solution to produce compressed bricks. This serves as one of the recycling efforts to conserve the environment. This study determined the optimum mix based on a mix ratio of 1:2:4 (cement: sand: soil) in the production of compressed bricks where 5 different mixes were investigated i. e. 0%, 5%, 10%, 20%, and 30% of water treatment plant residue solution. The production of the compressed bricks is in accordance with the Malaysian Standard MS 7.6: 1972 and British Standard BS 3921: 1985 - Compressive Strength & Water Absorption. After being moulded and air dried, the cured bricks were subjected to compression tests and water absorption tests. Based on the tests conducted, it was found that 20% of water treatment plant residue solution which is equivalent to 50% of soil content replacement with a mix composition of [10: cement] [20: sand] [20: soil] [20: water treatment plant residue solution] is the optimum mix. It was also observed that the bricks containing SWTP residuals were lighter in weight compared to the control specimens

  7. Immobilization in ceramic waste forms of the residues from treatment of mixed wastes

    International Nuclear Information System (INIS)

    Oversby, V.M.; van Konynenburg, R.A.; Glassley, W.E.; Curtis, P.G.

    1993-11-01

    The Environmental Restoration and Waste Management Applied Technology Program at LLNL is developing a Mixed Waste Management Facility to demonstrate treatment technologies that provide an alternative to incineration. As part of that program, we are developing final waste forms using ceramic processing methods for the immobilization of the treatment process residues. The ceramic phase assemblages are based on using Synroc D as a starting point and varying the phase assemblage to accommodate the differences in chemistry between the treatment process residues and the defense waste for which Synroc D was developed. Two basic formulations are used, one for low ash residues resulting from treatment of organic materials contaminated with RCRA metals, and one for high ash residues generated from the treatment of plastics and paper products. Treatment process residues are mixed with ceramic precursor materials, dried, calcined, formed into pellets at room temperature, and sintered at 1150 to 1200 degrees C to produce the final waste form. This paper discusses the chemical composition of the waste streams and waste forms, the phase assemblages that serve as hosts for inorganic waste elements, and the changes in waste form characteristics as a function of variation in process parameters

  8. Gas composition of sludge residue profiles in a sludge treatment reed bed between loadings

    DEFF Research Database (Denmark)

    Larsen, Julie Dam; Nielsen, Steen M; Scheutz, Charlotte

    2017-01-01

    Treatment of sludge in sludge treatment reed bed systems includes dewatering and mineralization. The mineralization process, which is driven by microorganisms, produces different gas species as by-products. The pore space composition of the gas species provides useful information on the biological...... processes occurring in the sludge residue. In this study, we measured the change in composition of gas species in the pore space at different depth levels in vertical sludge residue profiles during a resting period of 32 days. The gas composition of the pore space in the sludge residue changed during...... the resting period. As the resting period proceeded, atmospheric air re-entered the pore space at all depth levels. The methane (CH4) concentration was at its highest during the first part of the resting period, and then declined as the sludge residue became more dewatered and thereby aerated. In the pore...

  9. Characterisation of some South African water treatment residues ...

    African Journals Online (AJOL)

    2005-07-03

    Jul 3, 2005 ... (pH, electrical conductivity, cation exchange capacity, calcium carbonate equivalence, exchangeable acidity, extractable bases and metal cations, total ... Types and dosages of treatment chemicals vary depending on the .... in order to stress that it has a different nature to biosolids, South. African regulations ...

  10. Prevalence and spectrum of residual symptoms in Lyme neuroborreliosis after pharmacological treatment: a systematic review.

    Science.gov (United States)

    Dersch, R; Sommer, H; Rauer, S; Meerpohl, J J

    2016-01-01

    Controversy exists about residual symptoms after pharmacological treatment of Lyme neuroborreliosis. Reports of disabling long-term sequels lead to concerns in patients and health care providers. We systematically reviewed the available evidence from studies reporting treatment of Lyme neuroborreliosis to assess the prevalence and spectrum of residual symptoms after treatment. A literature search was performed in three databases and three clinical trial registers to find eligible studies reporting on residual symptoms in patients after pharmacological treatment of LNB. Diagnosis must have been performed according to consensus-derived case definitions. No restrictions regarding study design or language were set. Symptom prevalence was pooled using a random-effects model. Forty-four eligible clinical trials and studies were found: 8 RCTs, 17 cohort studies, 2 case-control studies, and 17 case series. The follow-up period in the eligible studies ranged from 7 days to 20 years. The weighted mean proportion of residual symptoms was 28 % (95 % CI 23-34 %, n = 34 studies) for the latest reported time point. Prevalence of residual symptoms was statistically significantly higher in studies using the "possible" case definition (p = 0.0048). Cranial neuropathy, pain, paresis, cognitive disturbances, headache, and fatigue were statistically significantly lower in studies using the "probable/definite" case definition. LNB patients may experience residual symptoms after treatment with a prevalence of approximately 28 %. The prevalence and spectrum of residual symptoms differ according to the applied case definition. Symptoms like fatigue are not reported in studies using the "probable/definite" case definition. As the "possible" case definition is more unspecific, patients with other conditions may be included. Reports of debilitating fatigue and cognitive impairment after LNB, a "post-Lyme syndrome", could therefore be an artifact of unspecific case definitions in single

  11. Immobilization of Co2+ and Cs+ in zeolites by thermal treatment and by combustion

    International Nuclear Information System (INIS)

    Rodriguez T, R.; Bulbulian G, S.

    2005-01-01

    The radioactive waste, either those that take place in the 235 U fission or those that are used in the radiochemical laboratories, are dangerous for the human being and for the one environment. The liquid radioactive wastes are of those that present bigger problem. It has intended to retain by the ion exchange method the radioactive ions of the liquids using, for example, zeolites. In this work so much synthetic zeolites was used (A and X) like a natural zeolite (clinoptilolite). Its were put in contact with cobalt or cesium solutions to simulate radioactive solutions. A part of the zeolite cations were exchanged with cobalt or cesium cations, eliminating them by this way of the solution. However, in extreme conditions these cations can be leached of the solids. To immobilize the cobalt or cesium cations in the zeolites net its are usually carried out thermal treatments to such temperatures that the structure is destroyed and that the contaminating ions are trapped in a solid often vitreous. The exchanged zeolites with cobalt or cesium, on one hand, its were thermally treated to different temperatures during three hours and by the other one, according to the treatment method by combustion, to different temperatures during five minutes in presence of urea, later its were put in contact with a solution of NaCl to measure the leaching of the interest cations. These solutions were analyzed by neutron activation. In general it was found that as the treatment temperature increases (in both methods) the so much immobility of the cesium like of the cobalt it increases. The grade of crystallinity of the samples before and after the treatments it was determined by X-ray diffraction. (Author)

  12. Mathematical modeling of the heat treatment and combustion of a coal particle. V. Burn-up stage

    Science.gov (United States)

    Enkhjargal, Kh.; Salomatov, V. V.

    2011-07-01

    The present material is a sequel of the previous publications of the authors in this journal under a common title in which by means of mathematical modeling the sequential stages of the process of combustion of coal fuels have been obtained: heating, drying, escape of volatiles, and ignition. Mathematical models of the final stage of combustion of an individual particle — the burn-up stage — have been formulated. On the basis of the solution methods for nonlinear boundary-value problems developed by us, approximate-analytic formulas for two characteristic regimes, burn-up simultaneously with the evaporation of the remaining moisture and burn-up of the completely dried coke residue, have been obtained. The previous history of the physical and chemical phenomena in the general burning pattern is taken into account. The influence of the ash shell on the duration of combustion has been extimated. Comparison of calculations by the obtained dependences with the results of other authors has been made. It showed an accuracy sufficient for engineering applications.

  13. Co-combustion of waste materials using fluidized bed technology

    Energy Technology Data Exchange (ETDEWEB)

    M. Lopes; I. Gulyurtlu; P. Abelha; T. Crujeira; D. Boavida; I. Cabrita [INETI-DEECA, Lisbon (Portugal)

    2004-07-01

    There is growing interest in using renewable fuels in order to sustain the CO{sub 2} accumulation. Several waste materials can be used as coal substitutes as long as they contain significant combustible matter, as for example MSW and sewage sludge. Besides the outcome of the energetic valorization of such materials, combustion must be regarded as a pre-treatment process, contributing to the safe management of wastes. Landfilling is an expensive management option and requires a previous destruction of the organic matter present in residues, since its degradation generates greenhouse gases and produces acidic organic leachates. Fluidized bed combustion is a promising technology for the use of mixtures of coal and combustible wastes. This paper presents INETI's experience in the co-combustion of coal with this kind of residues performed in a pilot fluidized bed. Both the RDF (from MSW and sewage sludge) and sewage sludge combustion problems were addressed, relating the gaseous emissions, the behaviour of metals and the leachability of ashes and a comparison was made between co-combustion and mono-combustion in order to verify the influence of the utilization of coal. 9 refs., 1 fig., 3 tabs.

  14. Handling of Solid Residues

    International Nuclear Information System (INIS)

    Medina Bermudez, Clara Ines

    1999-01-01

    The topic of solid residues is specifically of great interest and concern for the authorities, institutions and community that identify in them a true threat against the human health and the atmosphere in the related with the aesthetic deterioration of the urban centers and of the natural landscape; in the proliferation of vectorial transmitters of illnesses and the effect on the biodiversity. Inside the wide spectrum of topics that they keep relationship with the environmental protection, the inadequate handling of solid residues and residues dangerous squatter an important line in the definition of political and practical environmentally sustainable. The industrial development and the population's growth have originated a continuous increase in the production of solid residues; of equal it forms, their composition day after day is more heterogeneous. The base for the good handling includes the appropriate intervention of the different stages of an integral administration of residues, which include the separation in the source, the gathering, the handling, the use, treatment, final disposition and the institutional organization of the administration. The topic of the dangerous residues generates more expectation. These residues understand from those of pathogen type that are generated in the establishments of health that of hospital attention, until those of combustible, inflammable type, explosive, radio-active, volatile, corrosive, reagent or toxic, associated to numerous industrial processes, common in our countries in development

  15. Fungicide residues in pears and apples after post harvest treatments by drencher.

    Science.gov (United States)

    Donnarumma, L; Pompi, V; Rossi, E; Carfì, F

    2005-01-01

    Aim of this trial was to verify the residues of two fungicides, already authorised for the use in field (the admitted maximum limit of residues have been fixed), after post harvest treatments on pears and apples for defence against main post harvest rots. The use of formulation in post harvest must consider also the technique of product application. In fact there are different systems to carry out the treatments for the protection of the commodities during cold storage. In this trial two formulations of pyrimethanil and imazalil were applied by drencher on pome fruit.

  16. Formation of the residual stress due to the thermal treatment in Alloy 690 tubes

    International Nuclear Information System (INIS)

    Kim, Sung Soo; Kim, Joung Soo

    2004-01-01

    It is known that the steam generator tubes made of Alloy 600 have suffered primary coolant leakage accidents due to stress corrosion cracking (SCC). The one of main reasons for the susceptibility to SCC is understood to be chromium (Cr) depletion in the grain boundary. Therefore, the precipitation of carbide is controlled by heat treatment in the final manufacturing stage. In order to investigate the formation reason of residual stress in the steam generator tube systematically, the tube specimens were cooled both at inside and at outside tube after heat treatment and the residual stress formed during water quenching was measured by strain gage using sectioning method

  17. Technologies for the treatment of the sulfur dioxide and nitrogen oxides generated by the combustion in open chamber; Tecnologias para el tratamiento de dioxido de azufre y oxidos de nitrogeno generados por la combustion en camara abierta

    Energy Technology Data Exchange (ETDEWEB)

    Salazar Villalpando, Maria Dolores [Instituto Mexicano del Petroleo, Mexico, D. F. (Mexico)

    1992-12-31

    In general terms, there are only three ways of avoiding the sulfur dioxide and the nitrogen oxides, generated by the combustion in open chamber, from contaminating the air; the first one is utilizing low sulfur and nitrogen content fuels, the second one is by controlling the parameters that affect the combustion and the third one to treat and/or clean the gases before exhausting them to the air. In this document, some of the treatments for diminishing the pollutant emissions generated by the combustion in open chamber, are presented. [Espanol] En terminos generales, solo existen 3 maneras de evitar que el dioxido de azufre y oxidos de nitrogeno generados por la combustion en camara abierta sigan contaminando el aire, la primera es utilizar un combustible de bajo contenido de azufre y nitrogeno, la segunda es controlar los parametros que afectan la combustion, y la tercera es tratar y/o limpiar los gases antes de emitirlos a la atmosfera. En este documento se presentan algunos tratamientos para disminuir las emisiones de contaminantes generados por la combustion en camara abierta.

  18. Development of plasma melting technology for treatment of low level radioactive waste. Pt. 9. Treatment method for combustible wastes

    International Nuclear Information System (INIS)

    Yasui, Shinji; Adachi, Kazuo; Amakawa, Masashi

    1996-01-01

    This paper describes the incineration method for the miscellaneous solid waste containing the low level radioactive combustibles (wood, PE, PVC) in a plasma furnace. The maximum weights of the respective combustibles to be fed into the plasma furnace and the incineration conditions for continuous feeding of the respective combustibles were examined experimentally. As a result, a experimental equation which expresses the maximum weights of the respective combustibles to be fed in reference to the residence time in the plasma furnace was obtained by using apparent reaction rate constants. Furthermore, a calculation method for the feeding intervals in reference to the weights of the combustibles fed each time was obtained for the continuous feeding in the plasma furnace, and the method was found to be consistent with experimental results. (author)

  19. Effect of weathering transformations of coal combustion residuals on trace elements mobility in view of the environmental safety and sustainability of their disposal and use. II. Element release.

    Science.gov (United States)

    Stefaniak, Sebastian; Kmiecik, Ewa; Miszczak, Ewa; Szczepańska-Plewa, Jadwiga; Twardowska, Irena

    2015-06-01

    This paper is the second one of two companion papers. It presents results of a study aimed at assessing the effect of real time weathering transformations of Coal Combustion Residuals (CCRs) on trace element binding/release and its environmental implications. The study is based on the chemical composition of pore solutions extracted from primary alkaline Class F CCRs, 0 to >40 years old, sampled from the surface layer and vertical profiles at four selected typical CCRs impoundments. The long-term weathering transformations were found to lead to gradual acidification to pH elements to release during internal acidification processes occurring at consecutive Wash-out I (pH > 8), Dissolution II (8 ≥ pH ≥ 7) and Delayed Release III (pH elements occurring in the CCRs are represented by three major groups showing the highest release to pore water: (a) within the acidic pH range (Na, K, Zn, Fe, Cd, Mo, Cr, B, Mn, Be and Ni; (b) within the near-neutral pH range (Al, V, Ba, Cu and Ag) and also Sb, Hg and Co not analyzed at pH Elements whose concentrations exceeded the threshold values for good chemical status of groundwater (TVs) at all weathering stages over the entire pH range studied were K, Al, B, Cr, Mo, V, As, Se, Sb and Hg, while Na, Zn, Fe and Cd showed particularly high delayed release at pH < 7, thus confirming the need of a precautionary approach to CCRs uncontrolled disposal and bulk reuse as common fill in view of long term environmental safety and sustainability. Copyright © 2015 Elsevier Ltd. All rights reserved.

  20. Effects of coal combustion residues on survival, antioxidant potential, and genotoxicity resulting from full-lifecycle exposure of grass shrimp (Palaemonetes pugio Holthius)

    International Nuclear Information System (INIS)

    Kuzmick, Danika M.; Mitchelmore, Carys L.; Hopkins, William A.; Rowe, Christopher L.

    2007-01-01

    Coal combustion residues (CCRs), largely derived from coal-fired electrical generation, are rich in numerous trace elements that have the potential to induce sublethal effects including oxidative stress, alterations in antioxidant status and DNA single strand breaks (SSB). CCRs are frequently discharged into natural and man-made aquatic systems. As the effects of CCRs have received relatively little attention in estuarine systems, the estuarine grass shrimp, Palaemonetes pugio, was chosen for this study. Grass shrimp were exposed in the laboratory to CCR-enriched sediments and food over a full life cycle. Survival to metamorphosis was significantly reduced in CCR-exposed larvae (17 ± 4 versus 70 ± 13% in the controls) but not in the juveniles or adults. The COMET assay, a general but sensitive assay for genotoxicity, was used to quantify DNA SSB in the adults. Total antioxidant potential was examined to assess the overall antioxidant scavenging capacity of CCR-exposed and non-exposed adult grass shrimp. Grass shrimp exposed to CCR significantly accumulated selenium and cadmium compared to unexposed shrimp, although an inverse relationship was seen for mercury accumulation. Chronic CCR exposure caused DNA SSB in hepatopancreas cells, as evidenced by the significantly increased percent tail DNA, tail moment, and tail length as compared to reference shrimp. However, no significant difference was observed in total antioxidant potential. Our findings suggest that genotoxicity may be an important mode of toxicity of CCR, and that DNA SSB may serve as a useful biomarker of exposure and effect of this very common, complex waste stream

  1. Mindful Mood Balance: A Case Report of Web-Based Treatment of Residual Depressive Symptoms

    Science.gov (United States)

    Felder, Jennifer; Dimidjian, Sona; Beck, Arne; Boggs, Jennifer M; Segal, Zindel

    2014-01-01

    Residual depressive symptoms are associated with increased risk for relapse and impaired functioning. Although there is no definitive treatment for residual depressive symptoms, Mindfulness-Based Cognitive Therapy has been shown to be effective, but access is limited. Mindful Mood Balance (MMB), a Web-based adaptation of Mindfulness-Based Cognitive Therapy, was designed to address this care gap. In this case study, we describe a composite case that is representative of the course of intervention with MMB and its implementation in a large integrated delivery system. Specifically, we describe the content of each of eight weekly sessions, and the self-management skills developed by participating in this program. MMB may be a cost-effective and scalable option in primary care for increasing access to treatments for patients with residual depressive symptoms. PMID:25141988

  2. Mindful mood balance: a case report of Web-based treatment of residual depressive symptoms.

    Science.gov (United States)

    Felder, Jennifer; Dimidjian, Sona; Beck, Arne; Boggs, Jennifer M; Segal, Zindel

    2014-01-01

    Residual depressive symptoms are associated with increased risk for relapse and impaired functioning. Although there is no definitive treatment for residual depressive symptoms, Mindfulness-Based Cognitive Therapy has been shown to be effective, but access is limited. Mindful Mood Balance (MMB), a Web-based adaptation of Mindfulness-Based Cognitive Therapy, was designed to address this care gap. In this case study, we describe a composite case that is representative of the course of intervention with MMB and its implementation in a large integrated delivery system. Specifically, we describe the content of each of eight weekly sessions, and the self-management skills developed by participating in this program. MMB may be a cost-effective and scalable option in primary care for increasing access to treatments for patients with residual depressive symptoms.

  3. Treatment of waste incinerator air-pollution-control residues with FeSO4: Concept and product characterization

    DEFF Research Database (Denmark)

    Lundtorp, Kasper; Jensen, Dorthe Lærke; Sørensen, Mette Abildgaard

    2002-01-01

    This paper describes a new concept for treatment of air- pollution-control (APC) residues from waste incineration and characterises the wastewater and stabilised residues generated by the process. The process involves mixing of APC-residues with a ferrous sulphate solution and subsequent oxidation...

  4. The effectiveness of sewage treatment processes to remove faecal pathogens and antibiotic residues

    Science.gov (United States)

    Hendricks, Rahzia; Pool, Edmund John

    2012-01-01

    Pathogens and antibiotics enter the aquatic environment via sewage effluents and may pose a health risk to wild life and humans. The aim of this study was to determine the levels of faecal bacteria, and selected antibiotic residues in raw wastewater and treated sewage effluents from three different sewage treatment plants in the Western Cape, South Africa. Sewage treatment plant 1 and 2 use older technologies, while sewage treatment plant 3 has been upgraded and membrane technologies were incorporated in the treatment processes. Coliforms and Escherichia coli (E. coli) were used as bioindicators for faecal bacteria. A chromogenic test was used to screen for coliforms and E. coli. Fluoroquinolones and sulfamethoxazole are commonly used antibiotics and were selected to monitor the efficiency of sewage treatment processes for antibiotic removal. Enzyme Linked Immunosorbent Assays (ELISAs) were used to quantitate antibiotic residues in raw and treated sewage. Raw intake water at all treatment plants contained total coliforms and E. coli. High removal of E. coli by treatment processes was evident for treatment plant 2 and 3 only. Fluoroquinolones and sulfamethoxazole were detected in raw wastewater from all sewage treatment plants. Treatment processes at plant 1 did not reduce the fluoroquinolone concentration in treated sewage effluents. Treatment processes at plant 2 and 3 reduced the fluoroquinolone concentration by 21% and 31%, respectively. Treatment processes at plant 1 did not reduce the sulfamethoxazole concentration in treated sewage effluents. Treatment processes at plant 2 and 3 reduced sulfamethoxazole by 34% and 56%, respectively. This study showed that bacteria and antibiotic residues are still discharged into the environment. Further research needs to be undertaken to improve sewage treatment technologies, thereby producing a better quality treated sewage effluent. PMID:22242882

  5. POST-OPERATIONAL TREATMENT OF RESIDUAL NA COOLLANT IN EBR-2 USING CARBONATION

    Energy Technology Data Exchange (ETDEWEB)

    Sherman, S.; Knight, C.

    2011-03-08

    At the end of 2002, the Experimental Breeder Reactor Two (EBR-II) facility became a U.S. Resource Conservation and Recovery Act (RCRA) permitted site, and the RCRA permit1 compelled further treatment of the residual sodium in order to convert it into a less reactive chemical form and remove the by-products from the facility, so that a state of RCRA 'closure' for the facility may be achieved (42 U.S.C. 6901-6992k, 2002). In response to this regulatory driver, and in recognition of project budgetary and safety constraints, it was decided to treat the residual sodium in the EBR-II primary and secondary sodium systems using a process known as 'carbonation.' In early EBR-II post-operation documentation, this process is also called 'passivation.' In the carbonation process (Sherman and Henslee, 2005), the system containing residual sodium is flushed with humidified carbon dioxide (CO{sub 2}). The water vapor in the flush gas reacts with residual sodium to form sodium hydroxide (NaOH), and the CO{sub 2} in the flush gas reacts with the newly formed NaOH to make sodium bicarbonate (NaHCO{sub 3}). Hydrogen gas (H{sub 2}) is produced as a by-product. The chemical reactions occur at the exposed surface of the residual sodium. The NaHCO{sub 3} layer that forms is porous, and humidified carbon dioxide can penetrate the NaHCO{sub 3} layer to continue reacting residual sodium underneath. The rate of reaction is controlled by the thickness of the NaHCO{sub 3} surface layer, the moisture input rate, and the residual sodium exposed surface area. At the end of carbonation, approximately 780 liters of residual sodium in the EBR-II primary tank ({approx}70% of original inventory), and just under 190 liters of residual sodium in the EBR-II secondary sodium system ({approx}50% of original inventory), were converted into NaHCO{sub 3}. No bare surfaces of residual sodium remained after treatment, and all remaining residual sodium deposits are covered by a

  6. Analysis of residual stress relief mechanisms in post-weld heat treatment

    International Nuclear Information System (INIS)

    Dong, Pingsha; Song, Shaopin; Zhang, Jinmiao

    2014-01-01

    This paper presents a recent study on weld residual stress relief mechanisms associated with furnace-based uniform post-weld heat treatment (PWHT). Both finite element and analytical methods are used to quantitatively examine how plastic deformation and creep relaxation contribute to residual stress relief process at different stages of PWHT process. The key contribution of this work to an improved understanding of furnace based uniform PWHT can be summarized as follows: (1)Plastic deformation induced stress relief during PWHT can be analytically expressed by the change in material elastic deformation capacity (or elastic deformation limit) measured in terms of material yield strength to Young's modulus ratio, which has a rather limited role in overall residual stress relief during furnace based uniform PWHT. (2)The most dominant stress relief mechanism is creep strain induced stress relaxation, as expected. However, a rapid creep strain development accompanied by a rapid residual stress reduction during heating stage before reaching PWHT temperature is shown to contribute to most of the stress relief seen in overall PWHT process, suggesting PWHT hold time can be significantly reduced as far as residual stress relief is concerned. (3)A simple engineering scheme for estimating residual stress reduction is proposed based on this study by relating material type, PWHT temperature, and component wall thickness. - Highlights: • The paper clarified effects of plastic deformation and creep relaxation on weld residual stress relief during uniform PWHT. • Creep strain development is far more important than plastic strain, mostly completed even before hold time starts. • Plastic strain development is insignificant and be analytically described by a material elastic deformation capacity parameter. • An engineering estimation scheme is proposed for determining residual stress reduction resulted from furnace based PWHT

  7. Two-Stage Fungal Pre-Treatment for Improved Biogas Production from Sisal Leaf Decortication Residues

    Science.gov (United States)

    Muthangya, Mutemi; Mshandete, Anthony Manoni; Kivaisi, Amelia Kajumulo

    2009-01-01

    Sisal leaf decortications residue (SLDR) is amongst the most abundant agro-industrial residues in Tanzania and is a good feedstock for biogas production. Pre-treatment of the residue prior to its anaerobic digestion (AD) was investigated using a two-stage pre-treatment approach with two fungal strains, CCHT-1 and Trichoderma reesei in succession in anaerobic batch bioreactors. AD of the pre-treated residue with CCTH-1 at 10% (wet weight inoculum/SLDR) inoculum concentration incubated for four days followed by incubation for eight days with 25% (wet weight inoculum/SLDR) of T. reesei gave a methane yield of 0.292 ± 0.04 m3 CH4/kg volatile solids (VS)added. On reversing the pre-treatment succession of the fungal inocula using the same parameters followed by AD, methane yield decreased by about 55%. Generally, an increment in the range of 30–101% in methane yield in comparison to the un-treated SLDR was obtained. The results confirmed the potential of CCHT-1 followed by Trichoderma reesei fungi pre-treatment prior to AD to achieve significant improvement in biogas production from SLDR. PMID:20087466

  8. The History And Future Direction Of Wastewater Treatment Plant Residuals Disinfection And Energy Recovery Considerations

    Science.gov (United States)

    Presentation will review the history of disinfection practices for wastewater treatment plant residuals and discuss both the development and limitations of the U.S. regulations. Present U.S. regulations protect human health by minimizing the contact of humans with infectious mic...

  9. Sources of manganese in the residue from a water treatment plant ...

    African Journals Online (AJOL)

    Disposal of water treatment residue (WTR), the by-product from the production of potable water, has traditionally been to landfill. The shortage of suitable landfill sites has led to the proposal that WTR be applied to land. Such disposal is only possible if the WTR contains no toxic elements that may contaminate soil, water or ...

  10. Residue age and tree attractiveness influence efficacy of insecticide treatments against ambrosia beetles (Coleoptera: Curculionidae)

    Science.gov (United States)

    Management of ambrosia beetles in ornamental nurseries relies, in part, on treatments of insecticides to prevent beetles from boring into trees emitting stress-induced ethanol. However, data on residual efficacy of commonly used pyrethroid insecticides is warranted to gauge the duration that trees ...

  11. In situ neutron diffraction measurement of residual stress relaxation in a welded steel pipe during heat treatment

    International Nuclear Information System (INIS)

    Chen, B.; Skouras, A.; Wang, Y.Q.; Kelleher, J.F.; Zhang, S.Y.; Smith, D.J.; Flewitt, P.E.J.; Pavier, M.J.

    2014-01-01

    Many previous studies have presented results on the relaxation of residual stress in a welded component as a result of postweld heat treatment. Techniques such as neutron diffraction and deep hole drilling have been used to measure the residual stress after the heat treatment and compare this with the residual stress for the component in the as-welded condition. The work described in this paper is novel: neutron diffraction is used to measure the relaxation of residual stress continuously as the heat treatment is being carried out. Residual stresses are measured in a butt-welded ferritic steel pipe as the pipe is heat treated to 650 °C and then cooled to room temperature. The results identify those parts of the heat treatment that lead to significant stress relaxation and the mechanisms responsible for this relaxation. The techniques developed during this work allow future heat treatments to be optimised to achieve the low levels of residual stress in welded components

  12. Distinguishing benign confounding treatment changes from residual prostate cancer on MRI following laser ablation

    Science.gov (United States)

    Litjens, G.; Huisman, H.; Elliott, R.; Shih, N.; Feldman, M.; Viswanath, S.; Fütterer, J.; Bomers, J.; Madabhushi, A.

    2014-03-01

    Laser interstitial thermotherapy (LITT) is a relatively new focal therapy technique for the ablation of localized prostate cancer. However, very little is known about the specific effects of LITT within the ablation zone and the surrounding normal tissue regions. For instance, it is important to be able to assess the extent of residual cancer within the prostate following LITT, which may be masked by thermally induced benign necrotic changes. Fortunately LITT is MRI compatible and hence this allows for quantitatively assessing LITT induced changes via multi-parametric MRI. Of course definite validation of any LITT induced changes on MRI requires confirmation via histopathology. The aim of this study was to quantitatively assess and distinguish the imaging characteristics of prostate cancer and benign confounding treatment changes following LITTon 3 Tesla multi-parametric MRI by carefully mapping the treatment related changes from the ex vivo surgically resected histopathologic specimens onto the pre-operative in vivo imaging. A better understanding of the imaging characteristics of residual disease and successfully ablated tissue might lead to improved treatment monitoring and as such patient prognosis. A unique clinical trial at the Radboud University Medical Center, in which 3 patients underwent a prostatectomy after LITT treatment, yielded ex-vivo histopathologic specimens along with pre- and post-LITT MRI. Using this data we (1) identified the computer extracted MRI signatures associated with treatment effects including benign necrotic changes and residual disease and (2) subsequently evaluated the computer extracted MRI features previously identified in distinguishing LITT induced changes in the ablated area relative to the residual disease. Towards this end first a pathologist annotated the ablated area and the residual disease on the ex-vivo histology and then we transferred the annotations to the post-LITT MRI using semi-automatic elastic registration. The

  13. Treatment and use of air pollution control residues from MSW incineration: an overview.

    Science.gov (United States)

    Quina, Margarida J; Bordado, João C; Quinta-Ferreira, Rosa M

    2008-11-01

    This work reviews strategies for the management of municipal solid waste incineration (MSWI) residues, particularly solid particles collected from flue gases. These tiny particles may be retained by different equipment, with or without additives (lime, activated carbon, etc.), and depending on the different possible combinations, their properties may vary. In industrial plants, the most commonly used equipment for heat recovery and the cleaning of gas emissions are: heat recovery devices (boiler, superheater and economiser); dry, semidry or wet scrubbers; electrostatic precipitators; bag filters; fabric filters, and cyclones. In accordance with the stringent regulations in force in developed countries, these residues are considered hazardous, and therefore must be treated before being disposed of in landfills. Nowadays, research is being conducted into specific applications for these residues in order to prevent landfill practices. There are basically two possible ways of handling these residues: landfill after adequate treatment or recycling as a secondary material. The different types of treatment may be grouped into three categories: separation processes, solidification/stabilization, and thermal methods. These residues generally have limited applications, mainly due to the fact that they tend to contain large quantities of soluble salts (NaCl, KCl, calcium compounds), significant amounts of toxic heavy metals (Pb, Zn, Cr, Cu, Ni, Cd) in forms that may easily leach out, and trace quantities of very toxic organic compounds (dioxin, furans). The most promising materials for recycling this residue are ceramics and glass-ceramic materials. The main purpose of the present paper is to review the published literature in this field. A range of studies have been summarized in a series of tables focusing upon management strategies used in various countries, waste composition, treatment processes and possible applications.

  14. Persistence of gentamicin residues in milk after the intramammary treatment of lactating cows for mastitis*

    Science.gov (United States)

    Tan, Xun; Jiang, Ye-wen; Huang, Yi-jun; Hu, Song-hua

    2009-01-01

    This study was designed to investigate persistence of gentamicin residues in milk after the intramammary treatment of lactating cows for mastitis. Milk samples were collected at a 1-d interval after the last administration from 34 individual cows that had received intramammary infusions of gentamicin. The doses and treatment times evaluated in this study represented those that have been applied by veterinarians in practice. The tetrazolium chloride assay was used to determine whether there were significant residues of the antibiotic in the samples. Persistence of detectable drug residues in milk from 33 cows (28 cows, ≤6 infusions at ≤0.7 g gentamicin; and 5 cows, 2 infusions at 0.8 g gentamicin) did not exceed 5 d; but 1 cow (5 infusions at 0.8 g gentamicin) had detectable residues in its milk for 9 d. Our results suggest that a 5-d milk withdrawal period might be insufficient to secure the clearance of the contamination of gentamicin, because treatment times and dosages contribute to the antibiotic clearance. A larger scale of samples are needed for further investigations. PMID:19353746

  15. Evaluation of different water-washing treatments effects on wheat straw combustion properties.

    Science.gov (United States)

    Ma, Qiulin; Han, Lujia; Huang, Guangqun

    2017-12-01

    A series of experiments was conducted to explore the effects of various water-washing solid-liquid ratios (1:50 and 1:10) and the stirring on wheat straw (WS) combustion properties. Comparing different solid-liquid ratio groups, a 16% increment in the higher heating value was obtained for 1:50 groups and only 5% for 1:10 groups relative to the raw material. Moreover, energy was lost 4-26 times greater in 1:10 groups than 1:50 groups. While water-washing reduced the comprehensive combustibility index by 14.89%-32.09%, the index values of washed WS were all higher than 2, indicating good combustion performance. The combustion activation energy of four washed WS were 175, 172, 186, and 176kJ/mol, which were all higher than the 160kJ/mol of WS. The fouling/slagging propensity of washed WS reduced to a lower possibility compared to medium of untreated WS. Overall, the recommended condition for washing WS before combustion is 1:50 ratio without stirring. Copyright © 2017. Published by Elsevier Ltd.

  16. Optimization of Residual Stress of High Temperature Treatment Using Genetic Algorithm and Neural Network

    Directory of Open Access Journals (Sweden)

    M. Susmikanti

    2015-12-01

    Full Text Available In a nuclear industry area, high temperature treatment of materials is a factor which requires special attention. Assessment needs to be conducted on the properties of the materials used, including the strength of the materials. The measurement of material properties under thermal processes may reflect residual stresses. The use of Genetic Algorithm (GA to determine the optimal residual stress is one way to determine the strength of a material. In residual stress modeling with several parameters, it is sometimes difficult to solve for the optimal value through analytical or numerical calculations. Here, GA is an efficient algorithm which can generate the optimal values, both minima and maxima. The purposes of this research are to obtain the optimization of variable in residual stress models using GA and to predict the center of residual stress distribution, using fuzzy neural network (FNN while the artificial neural network (ANN used for modeling. In this work a single-material 316/316L stainless steel bar is modeled. The minimal residual stresses of the material at high temperatures were obtained with GA and analytical calculations. At a temperature of 6500C, the GA optimal residual stress estimation converged at –711.3689 MPa at adistance of 0.002934 mm from center point, whereas the analytical calculation result at that temperature and position is -975.556 MPa . At a temperature of 8500C, the GA result was -969.868 MPa at 0.002757 mm from the center point, while with analytical result was -1061.13 MPa. The difference in residual stress between GA and analytical results at a temperatureof6500C is about 27 %, while at 8500C it is 8.67 %. The distribution of residual stress showed a grouping concentrated around a coordinate of (-76; 76 MPa. The residuals stress model is a degree-two polynomial with coefficients of 50.33, -76.54, and -55.2, respectively, with a standard deviation of 7.874.

  17. Stabilization of arsenic and chromium polluted soils using water treatment residues

    DEFF Research Database (Denmark)

    Nielsen, Sanne Skov

    or other sorbents. Iron water treatment residues mainly consist of ferrihydrite, an oxidized iron oxy-hydroxide with a high reactivity and a large specific surface area with a high capacity for adsorption. Iron water treatment residues (Fe-WTR) are a by-product from treatment of groundwater to drinking...... in the leachate from an amended, slightly polluted soil (255 mg/kg As and 27 mg/kg Cr) did not at any time exceed 50 μg/L, which means that the soil can be reused for construction e.g. roads and baffle walls as described by the Danish Reuse Act. Ageing of ferrihydrite, the main constituent of Fe...

  18. Study on Influence to Waste Water Treatment Plant’s Sludge by Low-carbon Catalytic Combustion Furnace of Natural Gas

    OpenAIRE

    Ren TianQi; Fang Kai; Zhang Shihong

    2016-01-01

    There are two parts in this experiment. One of is about the concentration of Variation of exhaust gas while heating sludge of waste water treatment plant. The other one is about introduce the problems of the traditional incineration processes of sludge of waste water treatment as compared between the sludge heated by natural gas catalytic combustion furnace and the tradition’s. We can see that natural gas low-carbon catalytic combustion furnace realize the near-zero emission of contaminates.

  19. Production of geopolymers using glass produced from DC plasma treatment of air pollution control (APC) residues.

    Science.gov (United States)

    Kourti, Ioanna; Rani, D Amutha; Deegan, D; Boccaccini, A R; Cheeseman, C R

    2010-04-15

    Air pollution control (APC) residues are the hazardous waste produced from cleaning gaseous emissions at energy-from-waste (EfW) facilities processing municipal solid waste (MSW). APC residues have been blended with glass-forming additives and treated using DC plasma technology to produce a high calcium alumino-silicate glass. This research has investigated the optimisation and properties of geopolymers prepared from this glass. Work has shown that high strength geopolymers can be formed and that the NaOH concentration of the activating solution significantly affects the properties. The broad particle size distribution of the APC residue glass used in these experiments results in a microstructure that contains unreacted glass particles included within a geopolymer binder phase. The high calcium content of APC residues may cause the formation of some amorphous calcium silicate hydrate (C-S-H) gel. A mix prepared with S/L=3.4, Si/Al=2.6 and [NaOH]=6M in the activating solution, produced high strength geopolymers with compressive strengths of approximately 130 MPa. This material had high density (2070 kg/m(3)) and low porosity. The research demonstrates for the first time that glass derived from DC plasma treatment of APC residues can be used to form high strength geopolymer-glass composites that have potential for use in a range of applications. 2009 Elsevier B.V. All rights reserved.

  20. Human health effects of residual carbon nanotubes and traditional water treatment chemicals in drinking water.

    Science.gov (United States)

    Simate, Geoffrey S; Iyuke, Sunny E; Ndlovu, Sehliselo; Heydenrych, Mike; Walubita, Lubinda F

    2012-02-01

    The volume of industrial and domestic wastewater is increasing significantly year by year with the change in the lifestyle based on mass consumption and mass disposal brought about by the dramatic development of economies and industries. Therefore, effective advanced wastewater treatment is required because wastewater contains a variety of constituents such as particles, organic materials, and emulsion depending on the resource. However, residual chemicals that remain during the treatment of wastewaters form a variety of known and unknown by-products through reactions between the chemicals and some pollutants. Chronic exposure to these by-products or residual chemicals through the ingestion of drinking water, inhalation and dermal contact during regular indoor activities (e.g., showering, bathing, cooking) may pose cancer and non-cancer risks to human health. For example, residual aluminium salts in treated water may cause Alzheimer's disease (AD). As for carbon nanotubes (CNTs), despite their potential impacts on human health and the environment having been receiving more and more attention in the recent past, existing information on the toxicity of CNTs in drinking water is limited with many open questions. Furthermore, though general topics on the human health impacts of traditional water treatment chemicals have been studied, no comparative analysis has been done. Therefore, a qualitative comparison of the human health effects of both residual CNTs and traditional water treatment chemicals is given in this paper. In addition, it is also important to cover and compare the human health effects of CNTs to those of traditional water treatment chemicals together in one review because they are both used for water treatment and purification. Copyright © 2011 Elsevier Ltd. All rights reserved.

  1. Electrochemical treatment of wood combustion fly ash for the removal of cadmium

    DEFF Research Database (Denmark)

    Damø, Anne Juul

    2002-01-01

    Due to a high content of macronutrients and a potential liming capacity, recycling of ashes from biomass combustion to agricultural fields as fertilisers and/or for soil improvement is considered in Denmark and other countries utilising biomass as an energy source. However, especially the fly ash...... fractions contain amounts of the toxic heavy metal Cd that may exceed the limiting values for agricultural utilisation given by the Danish EPA. In this work the advances of using an electrochemical remediation method to reduce the Cd content in wood combustion fly ash - for the aim of recycling...

  2. Investigation of patient, tumour and treatment variables affecting residual motion for respiratory-gated radiotherapy

    Energy Technology Data Exchange (ETDEWEB)

    George, R [Department of Radiation Oncology, Virginia Commonwealth University, Richmond, VA (United States); Ramakrishnan, V [Department of Biostatistics, Virginia Commonwealth University, Richmond, VA (United States); Siebers, J V [Department of Radiation Oncology, Virginia Commonwealth University, Richmond, VA (United States); Chung, T D [Department of Radiation Oncology, Virginia Commonwealth University, Richmond, VA (United States); Keall, P J [Department of Radiation Oncology, Virginia Commonwealth University, Richmond, VA (United States)

    2006-10-21

    Respiratory gating can reduce the apparent respiratory motion during imaging and treatment; however, residual motion within the gating window remains. Respiratory training can improve respiratory reproducibility and, therefore, the efficacy of respiratory-gated radiotherapy. This study was conducted to determine whether residual motion during respiratory gating is affected by patient, tumour or treatment characteristics. The specific aims of this study were to: (1) identify significant characteristics affecting residual motion, (2) investigate time trends of residual motion over a period of days (inter-session) and (3) investigate time trends of residual motion within the same day (intra-session). Twenty-four lung cancer patients were enrolled in an Institutional Review Board (IRB)-approved protocol. For approximately five sessions, 331 four-minute, respiratory motion traces were acquired with free breathing, audio instructions and audio-visual biofeedback for each patient. The residual motion was quantified by the standard deviation of the displacement within the gating window. The generalized linear model was used to obtain coefficients for each variable within the model and to evaluate the clinical and statistical significance. The statistical significance was determined by a p-value <0.05, while effect sizes of {>=}0.1 cm (one standard deviation) were considered clinically significant. This data analysis was applied to patient, tumour and treatment variables. Inter- and intra-session variations were also investigated. The only variable that was significant for both inhale- and exhale-based gating was disease type. In addition, visual-training displacement, breathing type and Karnofsky performance status (KPS) values were significant for inhale-based gating, and dose-per-fraction was significant for exhale-based gating. Temporal respiratory variations within and between sessions were observed for individual patients. However inter- and intra-session analyses did

  3. Investigation of patient, tumour and treatment variables affecting residual motion for respiratory-gated radiotherapy

    Science.gov (United States)

    George, R.; Ramakrishnan, V.; Siebers, J. V.; Chung, T. D.; Keall, P. J.

    2006-10-01

    Respiratory gating can reduce the apparent respiratory motion during imaging and treatment; however, residual motion within the gating window remains. Respiratory training can improve respiratory reproducibility and, therefore, the efficacy of respiratory-gated radiotherapy. This study was conducted to determine whether residual motion during respiratory gating is affected by patient, tumour or treatment characteristics. The specific aims of this study were to: (1) identify significant characteristics affecting residual motion, (2) investigate time trends of residual motion over a period of days (inter-session) and (3) investigate time trends of residual motion within the same day (intra-session). Twenty-four lung cancer patients were enrolled in an Institutional Review Board (IRB)-approved protocol. For approximately five sessions, 331 four-minute, respiratory motion traces were acquired with free breathing, audio instructions and audio-visual biofeedback for each patient. The residual motion was quantified by the standard deviation of the displacement within the gating window. The generalized linear model was used to obtain coefficients for each variable within the model and to evaluate the clinical and statistical significance. The statistical significance was determined by a p-value =0.1 cm (one standard deviation) were considered clinically significant. This data analysis was applied to patient, tumour and treatment variables. Inter- and intra-session variations were also investigated. The only variable that was significant for both inhale- and exhale-based gating was disease type. In addition, visual-training displacement, breathing type and Karnofsky performance status (KPS) values were significant for inhale-based gating, and dose-per-fraction was significant for exhale-based gating. Temporal respiratory variations within and between sessions were observed for individual patients. However inter- and intra-session analyses did not show significant time

  4. Accumulation of ractopamine residues in hair and ocular tissues of animals during and after treatment.

    Science.gov (United States)

    Pleadin, Jelka; Vulic, Ana; Persi, Nina; Terzic, Svjetlana; Andrisic, Miroslav; Zarkovic, Irena; Sandor, Ksenija; Perak, Eleonora; Mihaljevic, Zeljko

    2013-03-01

    The aim of the present study was to assess the accumulation of ractopamine residues in the hair and ocular tissues of guinea pigs during repeated ractopamine administration and after treatment. The experiment was conducted in 38 guinea pigs (30 treated and eight controls). Treated animals were orally administered ractopamine hydrochloride in a dose of 3.5 mg/kg body mass per day using probes for seven consecutive days. Ractopamine concentration was determined in hair during the treatment (Days 1, 3 and 7) with ractopamine hydrochloride and in ocular tissues and hair on defined days after exposure (Days 1, 10, 20 and 30). Residues were present in hair in high concentrations as early as Day 3 (86.15 ± 87.71 ng/g) and Day 7 (85.25 ± 56.97 ng/g). After exposure, residues were found to persist, having depleted from 68.06 ± 30.54 ng/g on Day 1 to 8.01 ± 2.22 ng/g on Day 30, with a significantly higher concentration in hair in contrast to low residue levels in ocular tissues (1.20-0.34 ng/g). The results of the study pointed to high ractopamine accumulation, even in non-pigmented hair, suggesting hair to be used as a matrix in the control of ractopamine abuse in farm animals because of its many advantages over ocular tissues.

  5. Alternatives of Treatment and Final Disposition of the Solid Hospital residuals

    International Nuclear Information System (INIS)

    Meza Monge, K.

    1998-01-01

    The current handling, treatment and final disposition of the hospital solid waste in Costa Rica are considered inadequate or at least insufficient. This situation represents a serious danger for the population's health and the environment, because they are exposed to infectious agents, toxic substances and even radioactive products that are generated among the residuals of the centers of health. This work, alternatives propose for the treatment and adequate final disposition of the solid waste produced in the hospitals of the country. They take into consideration the characteristics that present these residuals, the advantages and disadvantages of each one of the existent techniques and the technical and economic possibilities of the country. For this purpose, in first instance, a revision about the properties, the quality and the quantity of the solid waste produced by the national hospital centers was carried out. Also, a diagnostic of the current situation of the treatment and final disposition of these residuals in some of the most important hospitals of the country, as well as of the possibilities of physical space with that they count on was carried out. Then, the existent different treatment techniques and final disposition for the solid waste that comes from the centers of health are described, as well as their advantages and disadvantages and a comparative analysis of the same ones is carried out. The objective is completed, since alternatives of treatment and final disposition that are considered appropriate for this type of residuals are planned. Nevertheless, in the future, more detailed investigations and studies of feasibility, with the purpose of developing handling programs and elimination of the solid waste for each one of the hospital centers in Costa Rica should be carried out. (Author) [es

  6. Characterization and electrodialytic treatment of wood combustion fly ash for removal of cadmium

    DEFF Research Database (Denmark)

    Pedersen, Anne Juul

    2003-01-01

    Due to a high content of macronutrients and a potential liming capacity, recycling of ashes from biomass combustion to agricultural fields as fertilisers and/or for soil improvement is considered in Denmark and other countries utilising biomass as an energy source. However, the fly ash fractions...

  7. Treatment of mine water and solid residues (RS) in San Rafael mining and milling complex

    International Nuclear Information System (INIS)

    Asenjo, Armando R.; Perrino, Juan F.

    2006-01-01

    San Rafael Mining and Milling Complex is located in Mendoza Province, in San Rafael Department, 38 km West from San Rafael city and 240 km south from Mendoza city, capital of the province. Activities related with yellow cake production were performed from 1979 to 1999. Nowadays the mine and the plant are in stand by. At the moment technical, economic and environmental studies are being done in order to restart the activities. Different kind of residues are accumulated in the site: a) Tailing; b) Sludges; c) Low grade ores; e) Waste rock; f) Mine water; g) Solid residues (RS). In this paper methodology to treat mine water and solid residues (RS) will be informed. a) Mine water: 800.000 m 3 of mine water are accumulated in different open pit. Uranium, radium and arsenic are the main ions to take into account to treat the water. Several laboratory and pilot test have been performed in order to define the treatment of the water, according with the regulatory requirement. A methodology using anion exchange resin to fix uranium and precipitation using barium chloride and iron sulfate to separate radium and arsenic has been developed. b) Solid residues (RS): these residues (precipitates) have been produced by neutralization of effluents in a nuclear purification process (TBP process). They are accumulated in drums. These residues come from Cordoba plant, a factory which produces UO 2 powder. The total content of uranium in the precipitate is 14.249 kg with an average uranium concentration of 1,33%. A methodology using sulfuric acid dissolution of the precipitates and anion exchange resin to recovery the uranium has been developed. (author) [es

  8. Accumulation of clenbuterol residues in the hair of Chinese Simmental beef cattle during and after treatment.

    Science.gov (United States)

    Li, Lijun; Zhang, Junmin; Tang, Chaohua; Zhao, Qingyu

    2014-01-01

    The aim of this study was to evaluate the concentrations of clenbuterol residues in the red hair of Chinese Simmental beef cattle following exposure to two doses of clenbuterol for 21 days. This experiment was conducted in six male red pied Chinese Simmental beef cattle which were randomly divided into two groups (n = 3). Groups 1 and 2 were administered clenbuterol at a dose of 16 and 48 μg/kg body weight (BW)/day, respectively. Hair samples were collected on Days 7, 14 and 21 during treatment, and on Days 0, 14, 28, 42 and 70 after discontinuation of medication, using liquid chromatography tandem mass spectrometry (LC-MS-MS) method. About 500 mg hair samples spiked with 50 pg/mg D9-clenbuterol internal standard were analyzed with which the method recovery was from 88.6 to 116.9%. The results showed that clenbuterol was significantly accumulated in hair, with a concentration of 0.98 ± 0.56 pg/mg in Group 1 and 6.34 ± 3.21 pg/mg in Group 2 on Day 7 of treatment, and the residue concentrations increased as treatment proceeded. During the early withdrawal period, the residues increased from 13.52 ± 8.69 to 17.96 ± 6.94 pg/mg in Group 1 and from 55.15 ± 4.04 to 147.79 ± 15.35 pg/mg in Group 2. No significant differences were found in the later withdrawal period in both treatment groups. The results of the present study indicated that the red hair of Chinese Simmental beef cattle has high accumulation potential for clenbuterol residues. Hair, as a target matrix, even light-pigmented hair, can be used to monitor clenbuterol abuse over a long period.

  9. Residue Age and Attack Pressure Influence Efficacy of Insecticide Treatments Against Ambrosia Beetles (Coleoptera: Curculionidae).

    Science.gov (United States)

    Reding, Michael E; Ranger, Christopher M

    2018-02-09

    Management of ambrosia beetles in ornamental nurseries relies, in part, on insecticide treatments to prevent beetles from boring into trees. However, data on residual efficacy of commonly used pyrethroid insecticides is needed to gauge the duration that trees are protected during spring when peak beetle pressure occurs. Residual efficacy of bifenthrin and permethrin trunk sprays was examined in field trials which used trees injected with 10% ethanol to ensure host attack pressure. Permethrin consistently reduced attacks by Xylosandrus germanus (Blandford; Coleoptera: Curculionidae) and other ambrosia beetles for at least 4 wk, while efficacy of bifenthrin was inconsistent and lasted only about 10 d. Since previous studies demonstrated attacks are positively correlated with host ethanol emissions, we injected trees with 2.5, 5, and 10% ethanol to determine if residual efficacy was affected by attack pressure. Preventive treatments with bifenthrin reduced ambrosia beetle attacks at all concentrations of injected ethanol compared to non-sprayed controls. There was no interaction between attack pressure and insecticide treatment with respect to total attacks or attacks by X. germanus. However, increasing attack pressure did increase the probability of attacks on insecticide treated trees by X. germanus and other Scolytinae. Results from our current study will improve the ability of growers to make decisions on frequency of protective sprays, but residual efficacy of insecticide treatments may decline as attack pressure increases. Cultural practices should therefore maximize host vigor and minimize attack pressure associated with stress-induced ethanol emissions. Published by Oxford University Press on behalf of Entomological Society of America 2017. This work is written by (a) US Government employee(s) and is in the public domain in the US.

  10. Application of coal combustion residues to the stabilization/solidification of industrial wastes (IRIS); Desarrollo de un Proceso, a Escala Piloto de Inertizacion de Residuos Industriales con Cenizas Volantes

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1998-12-31

    Stabilization/solidification (S/S) processes, also called inertization processes, are a group of techniques which employ additives to reduce the mobility of the hazardous components from the waste and make possible for the residue to be accepted for its disposal in a safe way. These processes, mainly applied to wastes that contain heavy metals (such as lead, zinc, cadminum, mercury, copper, nickel, titanium, chromium-III, chromium-VI, arsenic,....) change the waste into a solid-like material in which the metals are trapped (nets and matrix) by physical or chemical links. The IRIS Project, carried out by AICIA through the ECSC Coal Programme with the participation of two industrial partners (Sevillana de Electricidad and EGMASA, a public-owned company for waste treatment), has developed, at pilot scale, a new S/S process for inorganic industrial wastes that uses great quantities of fly ash in the place of other more commonly used and expansive reagents. A pilot plant for 200 kg/h has been designed, built and operated. This facility has allowed to add improvements and scientific foundations to existing S/S technology. It has also allowed to obtain industrial scale parameters for fixed and portable plants. Experiencie have been mainly carried out using fly ash from high quality coals, but types of ash have been tested coming from coals with a greater calcium content, from fluidised bed combustion boilers and from desulphurisation processes, giving very suitable characteristics for their application to S/S processes. The addition of fly ash (up to 30%) in the IRIS process improves the results in comparison with the S/S processes that use only cement, because the final pH obtained (8-11) does not allow amphoteric metallic ions to escape in the leachate. The same as other S/S processes, IRIS can be applied also to wastes that contain certain metals (chromium-VI, arsenic, for example) with specific pre-treatments (redox, for example). The efficiency of the IRIS treatment

  11. Fungicide residues in pears, apples and grapes after post harvest treatments by thermonebulization.

    Science.gov (United States)

    Pompi, V; Donnarumma, L; Rossi, E; Rosati, S

    2005-01-01

    In the context of trials conducted in cold store, in order to investigate efficacy of fruit protection applying agrochemicals, the fate during the storage of two active ingredients (a.i.): pyrimethanil and imazalil, have been studied. The experimental trials were done on eight varieties of apples and pears and two of grapes. Only field use of named pesticides was already authorised on fruits and maximum residue limits (MRL) fixed. In the present biennial experimentation (apples and pears in the first year; grapes in the second one). Two fungicides formulations were applied and treatments have been executed by thermonebulization technique. The storage cell, had a volume of 110 m3 filled up with the fruits until 80% of its capacity. Each fruit variety constituted one thesis of 4 replicates. For each trial, only one treatment was performed at the beginning of conservation period (72 days for pears and apples, and 57 days for grapes). In order to estimate fungicides persistence, residues determinations have been carried out. From results obtained especially on grape, not homogenous residues distribution on treated commodities was observed. For all theses, residue level has not evidenced statistically significant decrement as function of time, behaviour not as observed in field tests. The following average values of residues have been determined: in apples and pears, 0.7 mg/kg of imazalil much lower than 5 mg/kg (RML fixed for field use), and 1.2 mg/kg of pyrimethanil little higher than 1 mg/kg (RML fixed for field use); in grapes 0.5 mg/kg pyrimethanil much lower than 3 mg/kg (RML fixed for field use).

  12. Co-combustion of automotive shredder residue (ASR) and sewage sludge with a mixture of industrial and household waste in an 20MW fluidized bed combustor; Samfoerbraenning av bilfluff, roetslam och avfall i en 20 MW fluidbaeddpanna - Studier av braenslesammansaettningens paaverkan paa belaeggningsbildning

    Energy Technology Data Exchange (ETDEWEB)

    Eskilsson, David; Johansson, Andreas; Johansson, Linda; Wikstroem-Blomqvist, Evalena

    2007-07-01

    In order to prevent a further increased use of resources and to decrease the environmental impact from landfills, organic wastes are today diverted towards material and energy recovery. This creates a waste market with an increasing number of waste fractions that needs to be treated properly. As an example, in Sweden it has recently been prohibited to landfill source separated combustible waste (2002) and organic waste (2005). Wastes as automotive shredder residue (ASR) and sewage sludge can no longer be landfilled and needs to be either material or energy recovered, which challenge the waste treatment sector. This work investigates the effects of ASR and sewage sludge co-combustion in a 20 MW Energy-from-Waste plant (bubbling fluidised bed). The long term objective of the work is to increase the fuel flexibility, the boiler availability and the power production. This report focus on boiler operation and combustion performance in terms of agglomeration, deposit rates and emissions. In addition to the tests with ASR and sewage sludge, repeated measurements were performed during normal load as a reference. The results show that the co-combusted fractions of ASR and sewage sludge, which on mass basis constituted 6 % and 15 % respectively, did not increase the risk for agglomeration or deposits on heat-exchanging surfaces. Instead, compared to the two reference cases, the deposit rates decreased when sewage sludge was added. Only minor variation in the emissions was seen between the different cases. The levels of I-TEQs were far below the legislated values in all cases

  13. Control system of an anaerobia reactor used in the treatment of the Industrial residual waters

    International Nuclear Information System (INIS)

    Duque, Mauricio; Giraldo, Eugenio; Bello Frank

    1995-01-01

    The technology of the anaerobia digestion, has had a wide acceptance in the Colombian means for the treatment of industrial residual waters, especially for the economic advantages that it present and the good purification results. The technology of the anaerobia digestion for the treatment of residual waters, is based in the conversion of the organic matter present in the polluted waters, in methane and carbon dioxide. These two gases are removed of the reactor by means of special structures of gathering. Microorganisms that are sensitive to the changes of the pH mediate the conversion of the organic matter to CH4 and CO2. Therefore, the control on the pH is necessary for a correct behavior of the reactor. At the moment many industries are implementing plans of contamination control, that involve treatment of residual waters for means anaerobia. The present investigation is part of a wide work program in the technology of the anaerobia digestion. It is looked for to develop a monitored system and automatic control of reactors discharge anaerobia appraises, in a combined effort among the departments of Civil and Electric Engineering of the Andes University

  14. Mixed-waste treatment -- What about the residuals? A comparative analysis of MSO and incineration

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-06-01

    This report examines the issues concerning final waste forms, or residuals, that result from the treatment of mixed waste in molten salt oxidation (MSO) and incinerator systems. MSO is a technology with the potential to treat a certain segment of the waste streams at US Department of Energy (DOE) sites. MSO was compared with incineration because incineration is the best demonstrated available technology (BDAT) for the same waste streams. The Grand Junction Projects Office (GJPO) and Oak Ridge National Laboratory (ORNL) prepared this report for the DOE Office of Environmental Restoration (OER). The goals of this study are to objectively evaluate the anticipated residuals from MSO and incineration, examine regulatory issues for these final waste forms, and determine secondary treatment options. This report, developed to address concerns that MSO residuals present unique disposal difficulties, is part of a larger effort to successfully implement MSO as a treatment technology for mixed and hazardous waste. A Peer Review Panel reviewed the MSO technology in November 1991, and the implementation effort is ongoing under the guidance of the MSO Task Force.

  15. Characterization of aluminium-based water treatment residual for potential phosphorus removal in engineered wetlands

    International Nuclear Information System (INIS)

    Babatunde, A.O.; Zhao, Y.Q.; Burke, A.M.; Morris, M.A.; Hanrahan, J.P.

    2009-01-01

    Aluminium-based water treatment residual (Al-WTR) is the most widely generated residual from water treatment facilities worldwide. It is regarded as a by-product of no reuse potential and landfilled. This study assessed Al-WTR as potential phosphate-removing substrate in engineered wetlands. Results indicate specific surface area ranged from 28.0 m 2 g -1 to 41.4 m 2 g -1 . X-ray Diffraction, Fourier transform infrared and energy-dispersive X-ray spectroscopes all indicate Al-WTR is mainly composed of amorphous aluminium which influences its phosphorus (P) adsorption capacity. The pH and electrical conductivity ranged from 5.9 to 6.0 and 0.104 dS m -1 to 0.140 dS m -1 respectively, showing that it should support plant growth. Batch tests showed adsorption maxima of 31.9 mg P g -1 and significant P removal was achieved in column tests. Overall, results showed that Al-WTR can be used for P removal in engineered wetlands and it carries the benefits of reuse of a by-product that promotes sustainability. - Aluminium-based water treatment residual can be used for phosphorus removal in engineered wetlands!

  16. Mixed-waste treatment -- What about the residuals? A comparative analysis of MSO and incineration

    International Nuclear Information System (INIS)

    1993-06-01

    This report examines the issues concerning final waste forms, or residuals, that result from the treatment of mixed waste in molten salt oxidation (MSO) and incinerator systems. MSO is a technology with the potential to treat a certain segment of the waste streams at US Department of Energy (DOE) sites. MSO was compared with incineration because incineration is the best demonstrated available technology (BDAT) for the same waste streams. The Grand Junction Projects Office (GJPO) and Oak Ridge National Laboratory (ORNL) prepared this report for the DOE Office of Environmental Restoration (OER). The goals of this study are to objectively evaluate the anticipated residuals from MSO and incineration, examine regulatory issues for these final waste forms, and determine secondary treatment options. This report, developed to address concerns that MSO residuals present unique disposal difficulties, is part of a larger effort to successfully implement MSO as a treatment technology for mixed and hazardous waste. A Peer Review Panel reviewed the MSO technology in November 1991, and the implementation effort is ongoing under the guidance of the MSO Task Force

  17. Techniques of material-flow-specific residual waste treatment; Techniken der stoffstromspezifischen Restabfallbehandlung

    Energy Technology Data Exchange (ETDEWEB)

    Maak, D.; Collins, H.J. [Technische Univ. Braunschweig, Leichtweiss - Inst. fuer Wasserbau (Germany)

    1998-09-01

    The success achieved with large-scale plants for mechanical-biological residual waste treatment has led to a change of course in waste pretreatment. In view of the low emissions via the water and gas routes from landfilled wastes and the low costs of waste treatment some authorising authorities have meanwhile issued special licences pursuant to clause no. 2.4 of the Technical Code on Household Waste, thus enabling mechanical-biological residual waste treatment plants to continue operations beyond the year 2005. Beside offering a means of treatment and disposal, cost-effective mechanical-biological pretreatment also provides an opportunity for going over to material-flow-specific residual waste treatment. These process stages permit recirculating valuable materials and using other materials for energy production. They can be retrofitted on a modular basis in existing plants. If these advantages of the present innovative pretreatment methods are not used, then mechanical-biological pretreatment can still serve as a preparatory stage for thermal treatment. To date there has been no practical experience with this innovative method of residual waste treatment. However, industrial-scale trials have shown that each individual treatment stage is capable of being carried out successfully. [Deutsch] Die guten Erfolge im grosstechnischen Betrieb von Anlagen zur mechanisch-biologischen Restabfallbehandlung haben zu einer Kursaenderung bei der Vorbehandlung von Abfaellen gefuehrt. Geringe Emissionen der deponierten Abfaelle auf dem Gas- und Wasserpfad sowie geringe Kosten fuer die Behandlung der Abfaelle haben dazu gefuehrt, dass inzwischen bereits einige Genehmigungsbehoerden eine Ausnahmegenehmigung nach Nr. 2.4 der TA Siedlungsabfall erteilt haben und damit der Betrieb von mechanisch-biologischen Restabfallbehandlungsanlagen auch nach 2005 ermoeglicht wird. Neben der alleinigen Behandlung und Deponierung bietet die kostenguenstige Vorbehandlung mit mechanisch

  18. Minimal residual disease after long-term interferon-alpha2 treatment

    DEFF Research Database (Denmark)

    Utke Rank, Cecilie; Weis Bjerrum, Ole; Larsen, Thomas Stauffer

    2016-01-01

    burden by a highly sensitive quantitative PCR (qPCR) assay appears to be a useful tool for monitoring minimal residual disease (MRD) and evaluating treatment efficacy. This report expands and substantiates existing data, showing that IFN-alpha2 is a highly potent immunomodulating agent capable...... of inducing MRD with low-burden JAK2 V617F, major molecular response (MMR), complete hematological remission (CHR) and complete histomorphological normalization of the bone marrow in a sub-set of patients with ET and PV after long-term treatment (≥ 3.5 years). Furthermore, long-lasting hematological...

  19. Electrochemical treatment of wood combustion fly ash for the removal of cadmium

    DEFF Research Database (Denmark)

    Damø, Anne Juul

    2002-01-01

    fractions contain amounts of the toxic heavy metal Cd that may exceed the limiting values for agricultural utilisation given by the Danish EPA. In this work the advances of using an electrochemical remediation method to reduce the Cd content in wood combustion fly ash - for the aim of recycling......Due to a high content of macronutrients and a potential liming capacity, recycling of ashes from biomass combustion to agricultural fields as fertilisers and/or for soil improvement is considered in Denmark and other countries utilising biomass as an energy source. However, especially the fly ash...... - is described. The method, which is named electrodialytic remediation, uses a low voltage direct current a cleaning agent. Under optimised remediation conditions with the fly ash suspended in a 0.25 M ammonium citrate mixture, more than 70 % of the initial Cd was removed from the wood fly ash using...

  20. The Effect of Heat Treatment on Fe doped Al2O3 Nanoparticles Prepared by Aqueous Combustion Synthesis

    International Nuclear Information System (INIS)

    Dehzangi, A.; Jalal Rouhi; Saion, E.B.

    2011-01-01

    Iron doped Al 2 O 3 nanoparticles have been prepared from an aqueous combustion synthesis technique using stoichiometric amounts of aluminium nitrate [Al 9 NO 3 ) 3 .9H 2 O], ferric nitrate [Fe(NO 3 ) 3 .9H 2 O] and Sucrose sugar [C 12 H 22 O 11 ]. Heat treatment of the nanoparticles at tow temperatures (900 degree Celsius, 1100 degree Celsius) results in the formation of porous agglomerated iron doped alumina nanoparticles. Iron doped alumina were successfully synthesized by using sugar as fuel. The heat-treated powders have been characterized by X-ray diffraction, scanning electron microscopy and Energy-dispersive X-ray spectroscopy . (author)

  1. Experimental findings on thermal use of residues and biofuels in circulating fluidized bed combustion systems; Experimentelle Ergebnisse zur thermischen Nutzung von Rest- und Biobrennstoffen in zirkulierenden Wirbelschichtfeuerungen

    Energy Technology Data Exchange (ETDEWEB)

    Bernstein, W.; Brunne, T.; Girndt, H. [Technische Univ. Dresden (Germany); Albrecht, J. [Lurgi Lentjes Babcock, Frankfurt am Main (Germany); Youssef, M. [Minia Univ. (Egypt)

    1996-12-31

    The energy Engineering Institute of Dresden Technical University investigated the combustion and emission characteristics of a number of combustion systems, including a circulating fluidized bed system with a capacity of 0.3 MW{sub th}. Egypt`s sugar cane industry produces large volumes of bagasse. The conbustion and emission characteristics of this biofuel in a circulating fludized bed combustion systems were investigated in a joint research project of the University of Minia and Dresden Technical University. (orig.) [Deutsch] Am Institut fuer Energietechnik der TU Dresden wird das Verbrennungs- und Emissionsverhalten verschiedenster Brennstoffe in unterschiedlichen Feuerungssystemen untersucht. Neben anderen Pilotanlagen steht eine zirkulierende Wirbelschichtfeuerung (ZWFS) mit einer Leistung von 0.3 MW{sub th} zur Verfuegung. In der Zuckerrohrindustrie Aegyptens fallen grosse Mengen von Bagasse an. In einer gemeinsamen Forschungsarbeit zwischen der Universitaet Minia und der TU Dresden sollte das Verbrennungs- und Emissionsverhalten dieses Biobrennstoffes in einer ZWSF untersucht werden. (orig)

  2. Simulation of Distortion and Residual Stress Development During Heat Treatment of Steel Castings

    Energy Technology Data Exchange (ETDEWEB)

    Beckermann, Christoph; Carlson, Kent

    2011-07-22

    Heat treatment and associated processing, such as quenching, are critical during high strength steel casting production. These processes must be managed closely to prevent thermal and residual stresses that may result in distortion, cracking (particularly after machining), re-work, and weld repair. The risk of casting distortion limits aggressive quenching that can be beneficial to the process and yield an improved outcome. As a result of these distortions, adjustments must be made to the casting or pattern design, or tie bars must be added. Straightening castings after heat treatments can be both time-consuming and expensive. Residual stresses may reduce a casting's overall service performance, possibly resulting in catastrophic failure. Stress relieving may help, but expends additional energy in the process. Casting software is very limited in predicting distortions during heat treatment, so corrective measures most often involve a tedious trial-and-error procedure. An extensive review of existing heat treatment residual stress and distortion modeling revealed that it is vital to predict the phase transformations and microstructure of the steel along with the thermal stress development during heat treatment. After reviewing the state-of-the-art in heat treatment residual stress and distortion modeling, an existing commercial code was selected because of its advanced capabilities in predicting phase transformations, the evolving microstructure and related properties along with thermal stress development during heat treatment. However, this software was developed for small parts created from forgings or machined stock, and not for steel castings. Therefore, its predictive capabilities for heat treatment of steel castings were investigated. Available experimental steel casting heat treatment data was determined to be of insufficient detail and breadth, and so new heat treatment experiments were designed and performed, casting and heat treating modified versions

  3. Combustion behavior of spent solvent in a submerged combustion process

    International Nuclear Information System (INIS)

    Uchiyama, Gunzo; Maeda, Mitsuru; Fujine, Sachio; Amakawa, Masayuki; Uchida, Katsuhide.

    1993-10-01

    An experimental study has been conducted in order to evaluate the applicability of a submerged combustion technique to the treatment of spent solvents contaminated with TRU elements. A bench-scale equipment of submerged combustor having combustion capacity of 1.39 liter of tri-n-butyl phosphate (TBP) per hour was used to obtain process data such as the distribution behavior of radioactive nuclides in the submerged combustion process. This report describes the experimental results on the combustion characteristics of the simulated spent solvents of TBP and/or n-dodecane, and on the distribution behaviors of combustion products such as ruthenium and iodine in the submerged combustion process. (author)

  4. Effect of water treatment residuals on soil phosphorus, copper and aluminium availability and toxicity

    International Nuclear Information System (INIS)

    Lombi, E.; Stevens, D.P.; McLaughlin, M.J.

    2010-01-01

    Water treatment residuals (WTRs) are produced by the treatment of potable water with coagulating agents. Beneficial recycling in agriculture is hampered by the fact that WTRs contain potentially toxic contaminants (e.g. copper and aluminium) and they bind phosphorus strongly. These issues were investigated using a plant bioassay (Lactuca sativa), chemical extractions and an isotopic dilution technique. Two WTRs were applied to an acidic and a neutral pH soil at six rates. Reductions in plant growth in amended soils were due to WTR-induced P deficiency, rather than Al or Cu toxicity. The release of potentially toxic Al from WTRs was found to be mitigated by their alkaline nature and pH buffering capacity. However, acidification of WTRs was shown to release more soluble Al than soil naturally high in Al. Copper availability was relatively low in all treatments. However, the lability of WTR-Cu increased when the WTR was applied to the soil. - The effect of water treatment residue application to soil was investigated in relation to phosphorus availability, and copper and aluminium phytotoxicity.

  5. Effect of water treatment residuals on soil phosphorus, copper and aluminium availability and toxicity

    Energy Technology Data Exchange (ETDEWEB)

    Lombi, E., E-mail: enzo.lombi@unisa.edu.a [CSIRO Land and Water, Centre for Environmental Contaminant Research, PMB 2, Glen Osmond, SA 5064 (Australia); Centre for Environmental Risk Assessment and Remediation, University of South Australia, Building X, Mawson Lakes Campus, Mawson Lakes, SA 5095 (Australia); CRC CARE, PO Box 486, Salisbury, SA 5106 (Australia); Stevens, D.P. [CSIRO Land and Water, Centre for Environmental Contaminant Research, PMB 2, Glen Osmond, SA 5064 (Australia); Arris Pty Ltd, PO Box 5143, Burnley, Victoria 3121 (Australia); McLaughlin, M.J. [CSIRO Land and Water, Centre for Environmental Contaminant Research, PMB 2, Glen Osmond, SA 5064 (Australia); Soil and Land Systems, University of Adelaide, PMB 1, Glen Osmond, SA 5064 (Australia)

    2010-06-15

    Water treatment residuals (WTRs) are produced by the treatment of potable water with coagulating agents. Beneficial recycling in agriculture is hampered by the fact that WTRs contain potentially toxic contaminants (e.g. copper and aluminium) and they bind phosphorus strongly. These issues were investigated using a plant bioassay (Lactuca sativa), chemical extractions and an isotopic dilution technique. Two WTRs were applied to an acidic and a neutral pH soil at six rates. Reductions in plant growth in amended soils were due to WTR-induced P deficiency, rather than Al or Cu toxicity. The release of potentially toxic Al from WTRs was found to be mitigated by their alkaline nature and pH buffering capacity. However, acidification of WTRs was shown to release more soluble Al than soil naturally high in Al. Copper availability was relatively low in all treatments. However, the lability of WTR-Cu increased when the WTR was applied to the soil. - The effect of water treatment residue application to soil was investigated in relation to phosphorus availability, and copper and aluminium phytotoxicity.

  6. Release of Inorganic Elements during Wood Combustion. Release to the Gas Phase of Inorganic Elements during: Wood Combustion. Part 1: Development and Evaluation of Quantification Methods

    DEFF Research Database (Denmark)

    van Lith, Simone Cornelia; Alonso-Ramírez, Violeta; Jensen, Peter Arendt

    2006-01-01

    During wood combustion, inorganic elements such as alkali metals, sulfur, chlorine, and some heavy metals are partly released to the gas phase, which may cause problems in combustion facilities because of deposit formation and corrosion. Furthermore, it may cause harmful emissions of gases...... elements was quantified by a mass balance based on the weights and inorganic compositions of the fuel and the ash residues obtained by high-temperature (500-1150 C) treatment in a laboratory-scale tube reactor. However, method A involved the pyrolysis and combustion of a small fuel sample (~30 g...

  7. Experimental evaluation of washing for treatment of combustible plutonium-contaminated materials

    International Nuclear Information System (INIS)

    Wilkins, J.D.; Wisbey, S.J.

    1983-03-01

    Laboratory scale experiments have been carried out in order to assess the potential of washing as a method for removing plutonium from contaminated combustible wastes. A wide range of aqueous (eg 1 M HNO 3 , 1 M NaOH) and organic (1,1,2-trichlorotrifluoroethane) reagents have been investigated. Both synthetically contaminated and real wastes have been investigated. The preferred wash reagent has been identified as 1 M sodium hydroxide solution; plutonium recoveries of ca.80 to 90% can be achieved. (author)

  8. Pyrolysis reactor and fluidized bed combustion chamber

    Science.gov (United States)

    Green, Norman W.

    1981-01-06

    A solid carbonaceous material is pyrolyzed in a descending flow pyrolysis reactor in the presence of a particulate source of heat to yield a particulate carbon containing solid residue. The particulate source of heat is obtained by educting with a gaseous source of oxygen the particulate carbon containing solid residue from a fluidized bed into a first combustion zone coupled to a second combustion zone. A source of oxygen is introduced into the second combustion zone to oxidize carbon monoxide formed in the first combustion zone to heat the solid residue to the temperature of the particulate source of heat.

  9. Case studies in residual use and energy conservation at wastewater treatment plants

    Energy Technology Data Exchange (ETDEWEB)

    Stewart, D. [Science Applications International Corp., Los Altos, CA (United States)

    1995-06-01

    The US Environmental Protection Agency (EPA) and the National Renewable Energy Laboratory (NREL) for the US Department of Energy (DOE) funded a study to document energy conservation activities and their effects on operation costs, regulatory compliance, and process optimization at several wastewater treatment plants (WWTPS). The purpose of this report is to review the efforts of wastewater treatment Facilities that use residuals as fuels. Case histories are presented for facilities that have taken measures to reduce energy consumption during wastewater treatment. Most of the WWTPs discussed in this report have retrofitted existing facilities to achieve energy conservation. The case studies of energy conservation measures found no effects on the facilities` ability to comply with NPDES permits. Indeed, energy conservation activities enhance environmental compliance in several ways.

  10. Treatment methods and comparative risks of thorium removal from waste residues

    Energy Technology Data Exchange (ETDEWEB)

    Porter, R.D.; Hamby, D.M.; Martin, J.E.

    1997-07-01

    This study was done to examine the risks of remediation and the effectiveness of removal methods for thorium and its associated radioactive decay products from various soils and wastes associated with DOE`s Formerly Utilized Sites Remedial Action Program (FUSRAP). Removal of {sup 230}Th from uranium process residues would significantly reduce the buildup of {sup 226}Ra (half-life of 1600 years), and since {sup 230}Th concentrations at most of the important sites greatly exceed the {sup 226}Ra concentrations, such removal would reduce the accumulation of additional radiation risks associated with {sup 226}Ra and its products; and, if treatment also removed {sup 226}Ra, these risks could be mitigated even further. Removal of {sup 232}Th from thorium process residues would remove the source material for {sup 228}Ra, and since {sup 228}Ra has a half-life of 5.76 years, its control at FUSRAP sites could be done with land use controls for the 30--50 years required for {sup 228}Ra and the risks associated with its decay products to decay away. It must be recognized, however, that treatment methods invariably require workers to process residues and waste materials usually with bulk handling techniques. These processes expose workers to the radioactivity in the materials, therefore, workers would incur radiological risks in addition to industrial accident risks. An important question is whether the potential reduction of future radiological risks to members of the public justifies the risks that are incurred by remediation workers due to handling materials. This study examines, first, the effectiveness of treatment and then the risks that would be associated with remediation.

  11. Treatment methods and comparative risks of thorium removal from waste residues

    International Nuclear Information System (INIS)

    Porter, R.D.; Hamby, D.M.; Martin, J.E.

    1997-07-01

    This study was done to examine the risks of remediation and the effectiveness of removal methods for thorium and its associated radioactive decay products from various soils and wastes associated with DOE's Formerly Utilized Sites Remedial Action Program (FUSRAP). Removal of 230 Th from uranium process residues would significantly reduce the buildup of 226 Ra (half-life of 1600 years), and since 230 Th concentrations at most of the important sites greatly exceed the 226 Ra concentrations, such removal would reduce the accumulation of additional radiation risks associated with 226 Ra and its products; and, if treatment also removed 226 Ra, these risks could be mitigated even further. Removal of 232 Th from thorium process residues would remove the source material for 228 Ra, and since 228 Ra has a half-life of 5.76 years, its control at FUSRAP sites could be done with land use controls for the 30--50 years required for 228 Ra and the risks associated with its decay products to decay away. It must be recognized, however, that treatment methods invariably require workers to process residues and waste materials usually with bulk handling techniques. These processes expose workers to the radioactivity in the materials, therefore, workers would incur radiological risks in addition to industrial accident risks. An important question is whether the potential reduction of future radiological risks to members of the public justifies the risks that are incurred by remediation workers due to handling materials. This study examines, first, the effectiveness of treatment and then the risks that would be associated with remediation

  12. Residual stress in repair welds measured with neutron diffraction with and without post weld heat treatment

    International Nuclear Information System (INIS)

    Price, J.W.H.; Paradowska, A.M.; Finlayson, T.

    2010-01-01

    In welding, residual stresses (RS) are formed in the structure as the result of differential contractions which occur as the weld metal solidifies and cools to ambient temperature. The tensile stresses can have significant effects on the susceptibility of a material to degradation mechanisms such as fatigue, corrosion, fracture resistance, and creep. Welding repairs have increasingly become a structural integrity concern for aging pressure vessel and piping components. Both the repair procedure and the subsequent safety assessment, such as BS7910 and R6 require a better understanding of the welding effect on structural components. The use of a neutron beam as a non-destructive method of measuring residual stress due to repair welding has been explored. Two types of full penetration butt weld repairs on 25 mm ferritic steel were examined. From the findings of this research in terms of residual stress, temper bead welding repair may not be better than stringer bead welding. Post-weld heat treatment may be still advisable for temper bead weld repairs on ferritic steel.

  13. Temperature Field Prediction for Determining the Residual Stresses Under Heat Treatment of Aluminum Alloys

    Directory of Open Access Journals (Sweden)

    A. V. Livshits

    2014-01-01

    Full Text Available The article is devoted to non-stationary temperature field blanks from aluminum alloys during heat treatment. It consists of the introduction and two smaller paragraphs. In the introduction the author concerns the influence of residual stresses arising in the manufacturing process of details, on the strength of the whole aircraft construction and, consequently, on their technical and economic parameters, such as weight, reliability, efficiency, and cost. He also notes that the residual stresses appeared during the production of parts change their location, size and direction under the influence of the elastic deformations that occur during the exploitation of aircraft. Redistributed residual stresses may have a chaotic distribution that may cause overlap of these stresses on the stresses caused by the impact of workload of constructions and destruction or damage of aircraft components.The first paragraph is devoted to the existing methods and techniques for determining the residual stresses. The presented methods and techniques are analyzed to show the advantages and disadvantages of each of them. The conclusion is drawn that the method to determine the residual stresses is necessary, its cost is less than those of existing ones, and an error does not exceed 10%.In the second section, the author divides the problem of determining the residual stresses into two parts, and describes the solution methods of the first one. The first problem is to define the temperature field of the work piece. The author uses a Fourier equation with the definition of initial and boundary conditions to describe a mathematical model of the heat cycle of work piece cooling. He draws special attention here to the fact that it is complicated to determine the heat transfer coefficient, which characterizes the process of cooling the work piece during hardening because of its dependence on a number of factors, such as changing temperature-dependent material properties of

  14. Effect of shot peening treatment in the behavior of residual stress in duplex stainless steel during medium cycle fatigue

    International Nuclear Information System (INIS)

    Pedrosa, Peter D.S.; Rebello, Joao Marcos A.; Fonseca, Maria P. Cindra

    2010-01-01

    The lifetime of duplex stainless steel parts experiencing cyclic fatigue is directly influenced by the residual stresses present in the ferrite and austenite phases. The motivation for this work was to analyze the behaviour of the residual stresses fields introduced by shot peening treatment in both phases, in the sample surface as in the subsurface layers, in low fatigue cycles, using the X-rays diffraction technique. The results shows that the compressive residual stresses introduced by the shot peening treatment in both phases improved fatigue life of the material. However, the cyclical loads produce partial or total relief in these residual stresses fields. It was verified that the shot peening process induced the formation of microcracks only in the ferrite phase. The largest variations in the total compressive residual stresses fields also occurred in this phase. The samples surfaces were analyzed by scanning electron microscopy. (author)

  15. Insights into the mechanisms of mercury sorption onto aluminum based drinking water treatment residuals

    International Nuclear Information System (INIS)

    Deliz Quiñones, Katherine; Hovsepyan, Anna; Oppong-Anane, Akua; Bonzongo, Jean-Claude J.

    2016-01-01

    Highlights: • Mercury sorption by Al-WTRs involves electrostatic forces and chemisorption. • Hg forms bonds with oxygen and sulfur atoms of Al-WTR’s organic ligands. • Mercury is incorporated into the residual fraction to form stable complexes. • Mercury binds mainly to SiO x species in the residual fraction. - Abstract: Several studies have demonstrated the ability of drinking water treatment residuals (WTRs) to efficiently sorb metal cations from aqueous solutions. Reported results have stimulated interest on the potential use of WTRs as sorbent for metal removal from contaminated aqueous effluents as well as in metal immobilization in contaminated soils. However, knowledge on mechanisms of metal sorption by WTRs remains very limited and data on the long-term stability of formed metal–WTR complexes as a function of changing key environmental parameters are lacking. In this study, chemical selective sequential extraction (SSE), scanning electron microscopy combined with X-ray energy dispersive spectrometer (SEM-EDS), and X-ray photoelectron spectroscopy (XPS) were used to gain insight into the different mechanisms of mercury (Hg) binding to aluminum based WTR (Al-WTRs). Results from sorption studies show that a significant portion of Hg becomes incorporated in the operationally defined residual fraction of Al-WTRs, and therefore, not prone to dissolution and mobility. The results of solid phase analyses suggested that Hg immobilization by Al-WTR occurs largely through its binding to oxygen donor atoms of mineral ligands driven by a combination of electrostatic forces and covalent bonding.

  16. Thermal Treatment of Iron Oxide Stabilized APC Residues from Waste Incineration and the Effect on Heavy Metal Binding

    DEFF Research Database (Denmark)

    Sørensen, Mette Abildgaard; Stackpoole, M.; Bender-Koch, C.

    2000-01-01

    Iron oxide stabilized APC residues from MSWI were heat treated at 600°C and 900°C. The thermal treatments resulted in a change in product stability by forcing a transformation in the mineralogical structures of the products. The treatments, moreover, simulated somewhat the natural aging processes...... that would take place in a stabilized residue. Consequent changes in crystalline structure and heavy metal binding were examined....

  17. Boron and Coumaphos Residues in Hive Materials Following Treatments for the Control of Aethina tumida Murray.

    Directory of Open Access Journals (Sweden)

    Cesar Valdovinos-Flores

    Full Text Available In the search of alternatives for controlling Aethina tumida Murray, we recently proposed the BAA trap which uses boric acid and an attractant which mimics the process of fermentation caused by Kodamaea ohmeri in the hive. This yeast is excreted in the feces of A. tumida causing the fermentation of pollen and honey of infested hives and releasing compounds that function as aggregation pheromones to A. tumida. Since the boron is the toxic element in boric acid, the aim of this article is to assess the amount of boron residues in honey and beeswax from hives treated with the BAA trap. For this aim, the amount of bioaccumulated boron in products of untreated hives was first determined and then compared with the amount of boron of products from hives treated with the BAA trap in two distinct climatic and soil conditions. The study was conducted in the cities of Padilla, Tamaulipas, and Valladolid, Yucatan (Mexico from August 2014 to March 2015. The quantity of boron in honey was significantly less in Yucatan than in Tamaulipas; this agrees with the boron deficiency among Luvisol and Leptosol soils found in Yucatan compared to the Vertisol soil found in Tamaulipas. In fact, the honey from Yucatan has lower boron levels than those reported in the literature. The BAA treatment was applied for four months, results show that the BAA trap does not have any residual effect in either honey or wax; i.e., there is no significant difference in boron content before and after treatment. On the other hand, the organophosphate pesticide coumaphos was found in 100% of wax samples and in 64% of honey samples collected from Yucatan. The concentration of coumaphos in honey ranges from 0.005 to 0.040 mg/kg, which are below Maximum Residue Limit (MRL allowed in the European Union (0.1 mg/kg but 7.14% of samples exceeded the MRL allowed in Canada (0.02 mg/kg.

  18. Boron and Coumaphos Residues in Hive Materials Following Treatments for the Control of Aethina tumida Murray.

    Science.gov (United States)

    Valdovinos-Flores, Cesar; Gaspar-Ramírez, Octavio; Heras-Ramírez, María Elena; Lara-Álvarez, Carlos; Dorantes-Ugalde, José Antonio; Saldaña-Loza, Luz María

    2016-01-01

    In the search of alternatives for controlling Aethina tumida Murray, we recently proposed the BAA trap which uses boric acid and an attractant which mimics the process of fermentation caused by Kodamaea ohmeri in the hive. This yeast is excreted in the feces of A. tumida causing the fermentation of pollen and honey of infested hives and releasing compounds that function as aggregation pheromones to A. tumida. Since the boron is the toxic element in boric acid, the aim of this article is to assess the amount of boron residues in honey and beeswax from hives treated with the BAA trap. For this aim, the amount of bioaccumulated boron in products of untreated hives was first determined and then compared with the amount of boron of products from hives treated with the BAA trap in two distinct climatic and soil conditions. The study was conducted in the cities of Padilla, Tamaulipas, and Valladolid, Yucatan (Mexico) from August 2014 to March 2015. The quantity of boron in honey was significantly less in Yucatan than in Tamaulipas; this agrees with the boron deficiency among Luvisol and Leptosol soils found in Yucatan compared to the Vertisol soil found in Tamaulipas. In fact, the honey from Yucatan has lower boron levels than those reported in the literature. The BAA treatment was applied for four months, results show that the BAA trap does not have any residual effect in either honey or wax; i.e., there is no significant difference in boron content before and after treatment. On the other hand, the organophosphate pesticide coumaphos was found in 100% of wax samples and in 64% of honey samples collected from Yucatan. The concentration of coumaphos in honey ranges from 0.005 to 0.040 mg/kg, which are below Maximum Residue Limit (MRL) allowed in the European Union (0.1 mg/kg) but 7.14% of samples exceeded the MRL allowed in Canada (0.02 mg/kg).

  19. Boron and Coumaphos Residues in Hive Materials Following Treatments for the Control of Aethina tumida Murray

    Science.gov (United States)

    Valdovinos-Flores, Cesar; Gaspar-Ramírez, Octavio; Heras–Ramírez, María Elena; Dorantes-Ugalde, José Antonio; Saldaña-Loza, Luz María

    2016-01-01

    In the search of alternatives for controlling Aethina tumida Murray, we recently proposed the BAA trap which uses boric acid and an attractant which mimics the process of fermentation caused by Kodamaea ohmeri in the hive. This yeast is excreted in the feces of A. tumida causing the fermentation of pollen and honey of infested hives and releasing compounds that function as aggregation pheromones to A. tumida. Since the boron is the toxic element in boric acid, the aim of this article is to assess the amount of boron residues in honey and beeswax from hives treated with the BAA trap. For this aim, the amount of bioaccumulated boron in products of untreated hives was first determined and then compared with the amount of boron of products from hives treated with the BAA trap in two distinct climatic and soil conditions. The study was conducted in the cities of Padilla, Tamaulipas, and Valladolid, Yucatan (Mexico) from August 2014 to March 2015. The quantity of boron in honey was significantly less in Yucatan than in Tamaulipas; this agrees with the boron deficiency among Luvisol and Leptosol soils found in Yucatan compared to the Vertisol soil found in Tamaulipas. In fact, the honey from Yucatan has lower boron levels than those reported in the literature. The BAA treatment was applied for four months, results show that the BAA trap does not have any residual effect in either honey or wax; i.e., there is no significant difference in boron content before and after treatment. On the other hand, the organophosphate pesticide coumaphos was found in 100% of wax samples and in 64% of honey samples collected from Yucatan. The concentration of coumaphos in honey ranges from 0.005 to 0.040 mg/kg, which are below Maximum Residue Limit (MRL) allowed in the European Union (0.1 mg/kg) but 7.14% of samples exceeded the MRL allowed in Canada (0.02 mg/kg). PMID:27092938

  20. Effect of pre-treatments on methane production potential of energy crops and crop residues

    Energy Technology Data Exchange (ETDEWEB)

    Lehtomaki, A.; Ronkainen; Rintala, J.A. [Jyvaskla Univ. (Finland). Dept. of Biological and Environmental Sciences; Viinikainen, T.A. [Jyvaskla Univ. (Finland). Dept. of Chemistry

    2004-07-01

    Energy crops, that is, crops grown specifically for energy purposes are an alternative to food production in areas with sufficient agricultural land. Crop residues are also a potential source of energy. The anaerobic digestion of solid materials is limited by hydrolysis of complex polymeric substances such as lignocellulose. The methane producing potential of ligno cellulosic material is to pretreat the substrate in order to break up the polymer chains to more easily accessible soluble compounds. In this study, three different substrates were used: sugar beet tops, grass hay, and straw of oats. Biological pretreatments were the following: enzyme treatment, composting, white-rot fungi treatment. Also, pretreatment in water was tried. Chemical pretreatments included peracetic acid treatment, and treatment with two different alkalis. Alkaline pretreatments of hay and sugar beet tops have the potential to improve the methane yield. For instance, the yield of grass hay was increased 15 per cent by one particular alkaline treatment. Straw did not respond to any of the treatments tried. 18 refs., 1 tab., 2 figs.

  1. Performance of mechanical biological treatment of residual municipal waste in Poland

    Science.gov (United States)

    den Boer, Emilia; Jędrczak, Andrzej

    2017-11-01

    The number and capacity of mechanical-biological treatment (MBT) plants in Europe increased significantly in the past two decades as a response to the legal obligation to limit the landfilling of biodegradable waste in landfills and to increase recycling and energy recovery from waste. The aim of these plants is to prepare residual municipal waste for recovery and disposal operations, including especially separation and stabilization of the easily biodegradable fraction (the biofraction). The final products of MBP technology are recyclables, stabilate, high calorific fraction which is used for the production of refuse derived fuel (RDF) and the remaining residual fraction. The shares of the output fractions, especially of the recyclables and RDF determine the overall efficiency of MBT technology in diverting waste from landfills. In this paper results of an assessment of one exemplary MBT plant are provided. The analysis was performed within a comparative study in which 20 selected MBT plants in Poland were subject to a detailed analysis, focusing, both at the design parameters as well as operational ones. The selected plant showed relatively higher overall materials recovery efficiency. With the view to circular economy targets, increased automation of the mechanical waste treatment will be required to support achieving high level diversion from landfills. The study reviled that stabilisation of biofraction should be improved by a better control of process conditions, especially moisture content.

  2. Combining mechanical-biological residual waste treatment plants with grate firing; Kombination MBA mit Rostfeuerung

    Energy Technology Data Exchange (ETDEWEB)

    Fleck, E. [ABB Umwelttechnik GmbH, Butzbach (Germany)

    1998-09-01

    The promulgation of the Technical Code on Household Waste obliges the local authorities responsible for waste disposal to review existing and prepare new waste management plans. Given the present state of the art the Code`s limit value for loss due to burning of 5% makes thermal treatment of the residual waste practically compulsory. In preparation of these developments and in order to lower costs in general and be able respond flexibly to customer demands ABB is currently undertaking great efforts to provide thermal residual waste treatment plants with a modular design. [Deutsch] Mit Veroeffentlichung der TASi wurden die entsorgungspflichtigen Gebietskoerperschaften gezwungen, bereits vorhandene Abfall-Wirtschaftsplaene zu ueberarbeiten bzw. neue zu erstellen. Technisch laeuft nach derzeitigem Wissensstand der in der TASi vorgegebene maximale Gluehverlust von 5% darauf hinaus, dass eine thermische Behandlung des Restabfalls zwingend vorgegeben ist. Um hierfuer geruestet zu sein, aber auch um generell Kosten zu senken unf flexibel auf Kundenwuensche eingehen zu koennen, unternimmt ABB grosse Abstrengungen, den Aufbau von Anlagen zur thermischen Restabfallbehandlung modular zu gestalten. (orig./SR)

  3. Competitive Adsorption of Cadmium (II from Aqueous Solutions onto Nanoparticles of Water Treatment Residual

    Directory of Open Access Journals (Sweden)

    Elsayed Elkhatib

    2016-01-01

    Full Text Available There is increasing interest in using water treatment residuals (WTRs for heavy metals removal from wastewater due to their low cost, availability, and high efficiency in removing various pollutants. In this study, novel water treatment residuals nanoparticles (nWTRs were prepared using high energy ball milling and used for efficient removal of Cd(II in single- and multi-ion systems. The WTR nanoparticles demonstrated high removal efficiency for Cd from aqueous solution as the adsorption capacities of nWTR were 17 and 10 times higher than those of bulk WTR in single- and multielement systems, respectively. Noticeably, Cd(II adsorption was clearly suppressed in the multi-ion system as Cu and Pb form the most stable monohydroxo complexes. Fourier transmission infrared (FTIR analyses suggested the participation of OH−, O-Al-O, FeOH, and FeOOH entities in the adsorption process. The stability of Cd-nWTR surface complexes is evident as less than 0. 2% of adsorbed Cd(ll was released at the highest Cd(II concentration load after 4 consecutive desorption cycles. Moreover, the real efficiency of nWTR for Cd(II removal from wastewater samples studied was calculated to be 98.35%. These results highlight the potential of nWTR for heavy metals removal from wastewater.

  4. Study on Influence to Waste Water Treatment Plant’s Sludge by Low-carbon Catalytic Combustion Furnace of Natural Gas

    Directory of Open Access Journals (Sweden)

    Ren TianQi

    2016-01-01

    Full Text Available There are two parts in this experiment. One of is about the concentration of Variation of exhaust gas while heating sludge of waste water treatment plant. The other one is about introduce the problems of the traditional incineration processes of sludge of waste water treatment as compared between the sludge heated by natural gas catalytic combustion furnace and the tradition’s. We can see that natural gas low-carbon catalytic combustion furnace realize the near-zero emission of contaminates.

  5. Combustion noise

    Science.gov (United States)

    Strahle, W. C.

    1977-01-01

    A review of the subject of combustion generated noise is presented. Combustion noise is an important noise source in industrial furnaces and process heaters, turbopropulsion and gas turbine systems, flaring operations, Diesel engines, and rocket engines. The state-of-the-art in combustion noise importance, understanding, prediction and scaling is presented for these systems. The fundamentals and available theories of combustion noise are given. Controversies in the field are discussed and recommendations for future research are made.

  6. Mathematical modeling of the heat treatment and combustion of a coal particle. III. Volatile escape stage

    Science.gov (United States)

    Enkhjargal, Kh.; Salomatov, V. V.

    2011-05-01

    The present paper is a continuation of previous publications of the authors in this journal in which two phases of the multistage process of combustion of a coal particle were considered in detail with the help of mathematical modeling: its radiation-convection heating and drying. In the present work, the escape dynamics of volatiles is investigated. The physico-mathematical model of the thermodestruction of an individual coal particle with a dominant influence of endothermal effects has been formulated. Approximate-analytical solutions of this model that are of paramount importance for detailed analysis of the influence of the physical and regime parameters on the escape dynamics of volatiles have been found. The results obtained form the basis for engineering calculations of the volatile escape stage and can be used successfully in the search for effective regimes of burning of various solid fuels, in particular, Shivé-Ovoos coal of Mongolia.

  7. Mathematical modeling of the heat treatment and combustion of a coal particle. IV. Ignition stage

    Science.gov (United States)

    Enkhjargal, Kh.; Salomatov, V. V.

    2011-07-01

    The present paper is the continuation of the previous publications of the present authors in the Journal of Engineering Physics under the general title in which three sequential stages of the thermal preparation of a carbon particle for combustion are considered: heating, drying, and the yield of volatiles. The present paper is devoted to a detailed investigation of the stage of ignition of a carbon particle under the conditions of external radiative-convective supply that most adequately reflects the furnace medium. The characteristics of thermal ignition of a carbon matrix were studied with the aid of the adiabatic method. Such parameters as time and the heating temperature, the time of induction, the total time and the temperature of ignition of a carbon particle, the scale temperature, etc. have been found. The degree of dependence of the time of ignition on the initial temperature of the particle, the temperature of the external medium, heat transfer coefficient, and other inlet data has been analyzed.

  8. Full scale amendment of a contaminated wood impregnation site with iron water treatment residues

    DEFF Research Database (Denmark)

    Nielsen, Sanne Skov; Kjeldsen, Peter; Jakobsen, Rasmus

    2016-01-01

    Iron water treatment residues (Fe-WTR) are a free by-product of the treatment of drinking water with high concentration of iron oxides and potential for arsenic sorption. This paper aims at applying Fe-WTR to a contaminated site, measuring the reduction in contaminant leaching, and discussing...... amendment a 100 m2 test site and a control site (without amendment) were monitored for 14 months. Also soil analysis of Fe to evaluate the degree of soil and Fe-WTR mixing was done. Stabilization with Fe-WTR had a significant effect on leachable contaminants, reducing pore water As by 93%, Cu by 91% and Cr...... by 95% in the upper samplers. Dosage and mixing of Fe-WTR in the soil proved to be difficult in the deeper part of the field, and pore water concentrations of arsenic was generally higher. Despite water logged conditions no increase in dissolved iron or arsenic was observed in the amended soil. Our...

  9. A process for treatment of residues from dry/semidry APC systems at municipal solid waste incinerators. Final report

    Energy Technology Data Exchange (ETDEWEB)

    Hjelmar, O. [VKI, Hoersholm (Denmark)] Holland, D. [FLS miljoe a/s, Valby (Denmark)] Poulsen, B. [KARA, Roskilde (Denmark)

    1997-08-01

    The main objective of the project has been to establish and test a process for treatment of residues from the semidry (and dry) lime injection based APC processes at MSWIs, which will ensure that the residues can be managed in an environmentally safe manner. In pursuit of this goal, the following activities have been carried out: Performance of pilot scale extractions (approximately 50 kg of residue per batch) at the KARA MSWI in Roskilde of semidry APC system residues in order to establish and optimize process conditions. The optimization includes consideration of the possibilities for subsequent treatment/stabilization of the extracted solid phase as well as the possibility of treatment and safe discharge/utilization of the extract; Performance of chemical characterization, hydrogeochemical model calculations and experimental work in order to improve the understanding of the mechanisms and factors which for several contaminants control the equilibrium between the solid and liquid phases, both in the short and the long germ, and to use this information to obtain an environmentally acceptable method for stabilization/treatment of the extracted residues while at the same time minimizing the necessary amount of additives; production of treated residues and performance of leaching tests on these to assess and demonstrate the effectiveness of the entire process (extraction + stabilization/treatment); Evaluation of the technical, economical and environmental consequences of full scale implementation of the process. (EG) EFP-94. 19 refs.

  10. Examining heterogeneity in residual variance to detect differential response to treatments.

    Science.gov (United States)

    Kim, Jinok; Seltzer, Michael

    2011-06-01

    Individual differences in response to treatments have been a long-standing interest in education, psychology, and related fields. This article presents a conceptual framework and hierarchical modeling strategies that may help identify the subgroups for whom, or the conditions under which, a particular treatment is associated with better outcomes. The framework discussed in this article shows how differences in residual dispersion between treatment and control group members can signal omitted individual characteristics that may interact with treatments (Bryk & Raudenbush, 1988) and sensitizes us to individual- and cluster-level confounders of inferences concerning dispersion in quasi-experimental studies in multilevel settings. Based on the framework, hierarchical modeling strategies are developed to uncover interactions between treatments and individual characteristics, which are readily applicable to various settings in multisite evaluation studies. These strategies entail jointly modeling the mean and dispersion structures in hierarchical models. We illustrate the implementation of this framework through fully Bayesian analyses of the data from a study of the effectiveness of a reform-minded mathematics curriculum. © 2011 American Psychological Association

  11. Combustion testing and heat recovery study: Frank E. Van Lare Wastewater Treatment Plant, Monroe County. Final report

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-01-01

    The objectives of the study were to record and analyze sludge management operations data and sludge incinerator combustion data; ascertain instrumentation and control needs; calculate heat balances for the incineration system; and determine the feasibility of different waste-heat recovery technologies for the Frank E. Van Lare (FEV) Wastewater Treatment Plant. As an integral part of this study, current and pending federal and state regulations were evaluated to establish their impact on furnace operation and subsequent heat recovery. Of significance is the effect of the recently promulgated Federal 40 CFR Part 503 regulations on the FEV facility. Part 503 regulations were signed into law in November 1992, and, with some exceptions, affected facilities must be in compliance by February 19, 1994. Those facilities requiring modifications or upgrades to their incineration or air pollution control equipment to meet Part 503 regulations must be in compliance by February 19, 1995.

  12. Effects of post weld heat treatment and weld overlay on the residual stress and mechanical properties in dissimilar metal weld

    International Nuclear Information System (INIS)

    Campos, Wagner R.C.; Ribeiro, Vladimir S.; Vilela, Alisson H.F.; Almeida, Camila R.O.; Rabello, Emerson G.

    2017-01-01

    The object of this work is a dissimilar metal weld (DMW) pipe joint between carbon steel (A-106 Gr B) and stainless steel (A-312 TP316L) pipes and filler metals of Nickel alloy (82/182), which find wide application in the field of chemical, oil, petroleum industries, fossil fuel and nuclear power plant. A lot of the failures that have occurred in dissimilar metal welded are affected greatly by residual stresses. Residual stress is often a cause of premature failure of critical components under normal operation of welded components. Several methods have been tested and developed for removing the tensile residual stresses. The aim of the methods is to reduce the tensile stress state or to create compressive stresses at a predefined area, such as the inner surface of a welded pipe joint. Post weld heat treatment (PWHT) and weld overlay (WOL) are two of the residual stress mitigation methods which reduce the tensile residual stress, create compressive stresses and arrest crack initiation and crack growth. The technique used to substantially minimized or eliminated this failure development in the root weld is the post weld heat treatments (stress relief heat treatment) or the weld overlay. In this work was studied the effectiveness in reducing internal residual stress in dissimilar metal welded pipe joints subjected to post weld heat treatment and weld overlay, measurement by hole-drilling strain-gage method of stress relaxation. Also held was mechanical characterization of the welded pipe joint itself. (author)

  13. Effects of post weld heat treatment and weld overlay on the residual stress and mechanical properties in dissimilar metal weld

    Energy Technology Data Exchange (ETDEWEB)

    Campos, Wagner R.C.; Ribeiro, Vladimir S.; Vilela, Alisson H.F.; Almeida, Camila R.O.; Rabello, Emerson G., E-mail: wrcc@cdtn.br, E-mail: camilarezende.cr@gmail.com, E-mail: egr@cdtn.br, E-mail: vladimirsoler@hotmail.com, E-mail: ahfv02@outlook.com [Centro de Desenvolvimento da Tecnologia Nuclear (CDTN/CNEN-MG), Belo Horizonte, MG (Brazil)

    2017-07-01

    The object of this work is a dissimilar metal weld (DMW) pipe joint between carbon steel (A-106 Gr B) and stainless steel (A-312 TP316L) pipes and filler metals of Nickel alloy (82/182), which find wide application in the field of chemical, oil, petroleum industries, fossil fuel and nuclear power plant. A lot of the failures that have occurred in dissimilar metal welded are affected greatly by residual stresses. Residual stress is often a cause of premature failure of critical components under normal operation of welded components. Several methods have been tested and developed for removing the tensile residual stresses. The aim of the methods is to reduce the tensile stress state or to create compressive stresses at a predefined area, such as the inner surface of a welded pipe joint. Post weld heat treatment (PWHT) and weld overlay (WOL) are two of the residual stress mitigation methods which reduce the tensile residual stress, create compressive stresses and arrest crack initiation and crack growth. The technique used to substantially minimized or eliminated this failure development in the root weld is the post weld heat treatments (stress relief heat treatment) or the weld overlay. In this work was studied the effectiveness in reducing internal residual stress in dissimilar metal welded pipe joints subjected to post weld heat treatment and weld overlay, measurement by hole-drilling strain-gage method of stress relaxation. Also held was mechanical characterization of the welded pipe joint itself. (author)

  14. Replacement of 5% of OPC by fly ash and APC residues from MSWI with electrodialytic pre-treatment

    DEFF Research Database (Denmark)

    Magro, Cátia; Kirkelund, Gunvor Marie; Guedes, Paula

    2016-01-01

    Fly ash (FA) and air pollution control (APC) residues are waste products from Municipal Solid Waste Incineration (MSWI). They are classified as hazardous waste due to the content of leachable heavy metals (HM), salts and/or dioxins. An electrodialytic (ED) process was applied to FA and APC residues...... in the ash were not leached to the same extent as in the original ash. In mortar 5% of Ordinary Portland Cement was replaced by FA and APC residues (raw and ED upgraded). The studied parameters: compressive strength, HM leachability, and Cl content. The ED pre-treatment resulted in a decrease in both...... leaching of HM and the Cl content. The compressive tests presented comparable values to the reference mortars. This study suggests that the characteristics of FA and APC residues from MSWI after pre-treatment allows them to be reused in building materials, giving a new edge to waste management....

  15. Assays of residual antibiotics after treatment of γ-ray and UV irradiation

    International Nuclear Information System (INIS)

    Shin, Ji Hye; Nam, Ji Hyun; Lee, Dong Hun; Yu, Seung Ho; Lee, Myun Joo

    2010-01-01

    The pollution of antibiotics is a major cause of spreading antibiotics resistant bacteria in the environment. Applications of ozonation, UV, and γ-ray irradiations have been introduced to remove antibiotics in the effluents from wastewater treatment system. In this study, we compared the chemical (HPLC) and biological (antimicrobial susceptibility test, AMS) assays in measuring of the concentrations of residual antibiotics after γ-ray and UV irradiation. Most samples were degraded by γ-ray irradiation (1 ∼ 2 kGy). However, lincomycin and tetracycline were not degraded by UV irradiation. The concentration of residual antibiotics, that was treated with γ-ray and UV irradiation, measuring by bioassay was similar to HPLC. The concentrations of γ-ray irradiated cephradine measured by AMS test were 2 times higher than of HPLC assay, indicating AMS test is more sensitive than HPLC assay. These results indicate that γ-ray irradiation technique is more useful than UV irradiation, and biological assay is more useful to detect the antibiotics and toxic intermediates in antibiotics degradation

  16. Insights into the mechanisms of mercury sorption onto aluminum based drinking water treatment residuals.

    Science.gov (United States)

    Deliz Quiñones, Katherine; Hovsepyan, Anna; Oppong-Anane, Akua; Bonzongo, Jean-Claude J

    2016-04-15

    Several studies have demonstrated the ability of drinking water treatment residuals (WTRs) to efficiently sorb metal cations from aqueous solutions. Reported results have stimulated interest on the potential use of WTRs as sorbent for metal removal from contaminated aqueous effluents as well as in metal immobilization in contaminated soils. However, knowledge on mechanisms of metal sorption by WTRs remains very limited and data on the long-term stability of formed metal-WTR complexes as a function of changing key environmental parameters are lacking. In this study, chemical selective sequential extraction (SSE), scanning electron microscopy combined with X-ray energy dispersive spectrometer (SEM-EDS), and X-ray photoelectron spectroscopy (XPS) were used to gain insight into the different mechanisms of mercury (Hg) binding to aluminum based WTR (Al-WTRs). Results from sorption studies show that a significant portion of Hg becomes incorporated in the operationally defined residual fraction of Al-WTRs, and therefore, not prone to dissolution and mobility. The results of solid phase analyses suggested that Hg immobilization by Al-WTR occurs largely through its binding to oxygen donor atoms of mineral ligands driven by a combination of electrostatic forces and covalent bonding. Copyright © 2016 Elsevier B.V. All rights reserved.

  17. Integrating biological treatment of crop residue into a hydroponic sweetpotato culture

    Science.gov (United States)

    Trotman, A. A.; David, P. P.; Bonsi, C. K.; Hill, W. A.; Mortley, D. G.; Loretan, P. A.

    1997-01-01

    Residual biomass from hydroponic culture of sweetpotato [Ipomoea batatas (L.) Lam.] was degraded using natural bacterial soil isolates. Sweetpotato was grown for 120 days in hydroponic culture with a nutrient solution comprised of a ratio of 80% modified half Hoagland solution to 20% filtered effluent from an aerobic starch hydrolysis bioreactor. The phytotoxicity of the effluent was assayed with `Waldmann's Green' lettuce (Lactuca sativa L.) and the ratio selected after a 60-day bioassay using sweetpotato plants propagated vegetatively from cuttings. Controlled environment chamber experiments were conducted to investigate the impact of filtrate from biological treatment of crop residue on growth and storage root production with plants grown in a modified half Hoagland solution. Incorporation of bioreactor effluent, reduced storage root yield of `Georgia Jet' sweetpotato but the decrease was not statistically significant when compared with yield for plants cultured in a modified half Hoagland solution without filtrate. However, yield of `TU-82-155' sweetpotato was significantly reduced when grown in a modified half Hoagland solution into which filtered effluent had been incorporated. Total biomass was significantly reduced for both sweetpotato cultivars when grown in bioreactor effluent. The leaf area and dry matter accumulation were significantly (P < 0.05) reduced for both cultivars when grown in solution culture containing 20% filtered effluent.

  18. Amendment of arsenic and chromium polluted soil from wood preservation by iron residues from water treatment

    DEFF Research Database (Denmark)

    Nielsen, Sanne Skov; Petersen, L. R.; Kjeldsen, Peter

    2011-01-01

    , mostly in the deepest samplers. This is likely due to the formation of a pseudo-gley because of precipitation surplus. Stabilization of arsenic and chromium contaminated soil using WTR is a promising method but the transformation of ferrihydrite in soil proves a concern in case of waterlogged soils......An iron-rich water treatment residue (WTR) consisting mainly of ferrihydrite was used for immobilization of arsenic and chromium in a soil contaminated by wood preservatives. A leaching batch experiment was conducted using two soils, a highly contaminated soil (1033mgkg−1 As and 371mgkg−1 Cr......) and slightly contaminated soil (225mgkg−1 As and 27mgkg−1 Cr). Compared to an untreated reference soil, amendment with 5% WTR reduced leaching in the highly contaminated soil by 91% for Cr and 98% for As. No aging effect was observed after 103d. In a small field experiment, soil was mixed with 2.5% WTR in situ...

  19. Research of pathogenic bacteria and bacteriophages in the residuals of wastewater treatment plants

    International Nuclear Information System (INIS)

    Mathlouthi, Soumaya

    2011-01-01

    The aim of this study is to find the pathogenic bacteria Listeria and Salmonella and to detect of bacterial (fecal coliforms) and viral indicators (bacteriophage) of fecal contamination in the residues of three sewage treatment plants in Greater Tunis: Charguia, Jdaida and Wardia. Three types of samples were analyzed: raw sewage, treated wastewater and sludge. The study showed the presence of pathogenic bacteria in some samples with a frequency of 7 pour cent for Listeria and 21 pour cent for Salmonella. However, none of these organisms has been detected in treated water of Jdaida and Chargia reflecting the efficiency of the purification process in these stations. Furthermore, all samples were positive for the presence of fecal coliforms and bacteriophages with important titles: up to 8.23 log10 (CFU/L) for coliforms and 8.36 log10 (pfu/L) for bacteriophages.

  20. Upscaling Self-Sustaining Treatment for Active Remediation (STAR): Experimental Study of Scaling Relationships for Smouldering Combustion to Remediate Soil

    Science.gov (United States)

    Kinsman, L.; Gerhard, J.; Torero, J.; Scholes, G.; Murray, C.

    2013-12-01

    Self-sustaining Treatment for Active Remediation (STAR) is a relatively new remediation approach for soil contaminated with organic industrial liquids. This technology uses smouldering combustion, a controlled, self-sustaining burning reaction, to destroy nonaqueous phase liquids (NAPLs) and thereby render soil clean. While STAR has been proven at the bench scale, success at industrial scales requires the process to be scaled-up significantly. The objective of this study was to conduct an experimental investigation into how liquid smouldering combustion phenomena scale. A suite of detailed forward smouldering experiments were conducted in short (16 cm dia. x 22 cm high), intermediate (16 cm dia. x 127 cm high), and large (97 cm dia. x 300 cm high; a prototype ex-situ reactor) columns; this represents scaling of up to 530 times based on the volume treated. A range of fuels were investigated, with the majority of experiments conducted using crude oil sludge as well as canola oil as a non-toxic surrogate for hazardous contaminants. To provide directly comparable data sets and to isolate changes in the smouldering reaction which occurred solely due to scaling effects, sand grain size, contaminant type, contaminant concentration and air injection rates were controlled between the experimental scales. Several processes could not be controlled and were identified to be susceptible to changes in scale, including: mobility of the contaminant, heat losses, and buoyant flow effects. For each experiment, the propagation of the smouldering front was recorded using thermocouples and analyzed by way of temperature-time and temperature-distance plots. In combination with the measurement of continuous mass loss and gaseous emissions, these results were used to evaluate the fundamental differences in the way the reaction front propagates through the mixture of sand and fuel across the various scales. Key governing parameters were compared between the small, intermediate, and large

  1. Recycling potential of air pollution control residue from sewage sludge thermal treatment as artificial lightweight aggregates.

    Science.gov (United States)

    Bialowiec, Andrzej; Janczukowicz, Wojciech; Gusiatin, Zygmunt M; Thornton, Arthur; Rodziewicz, Joanna; Zielinska, Magdalena

    2014-03-01

    Thermal treatment of sewage sludge produces fly ash, also known as the air pollution control residue (APCR), which may be recycled as a component of artificial lightweight aggregates (ALWA). Properties of APCR are typical: high content of Ca, Mg, P2O5, as well as potential to induce alkaline reactions. These properties indicate that ALWA prepared with a high content of APCR may remove heavy metals, phosphorus, and ammonium nitrogen from wastewater with high efficiency. The aim of this preliminary study was to determine the optimal composition of ALWA for potential use as a filter media in wastewater treatment systems. Five kinds of ALWA were produced, with different proportions of ash (shown as percentages in subscripts) in mixture with bentonite: ALWA0 (reference), ALWA12.5, ALWA25, ALWA50, and ALWA100. The following parameters of ALWA were determined: density, bulk density, compressive strength, hydraulic conductivity, and removal efficiency of ions Zn(2+), NH4 (+), and PO4 (3-). Tests showed that ALWA had good mechanical and hydraulic properties, and might be used in wastewater filtering systems. Phosphates and zinc ions were removed with high efficiency (80-96%) by ALWA25-100 in static (batch) conditions. The efficiency of ammonium nitrogen removal was low, <18%. Artificial wastewater treatment performance in dynamic conditions (through-flow), showed increasing removal efficiency of Zn(2+), PO4 (3-) with a decrease in flow rate.

  2. Activation of peroxymonosulfate using drinking water treatment residuals for the degradation of atrazine.

    Science.gov (United States)

    Zhang, Huijuan; Liu, Xitao; Ma, Jun; Lin, Chunye; Qi, Chengdu; Li, Xiaowan; Zhou, Zhou; Fan, Guoxuan

    2018-02-15

    Drinking water treatment residuals (WTRs) are safe byproducts of water treatment plants containing iron. This work studies the degradation of atrazine (ATZ) by WTR-catalyzed peroxymonosulfate (PMS) in aqueous solutions. Factors that affect the catalytic performance (the PMS concentration, catalyst dose, initial solution pH, reaction temperature and water matrix species) were investigated. The results show that the catalytic degradation efficiency of ATZ increases with the increase in PMS concentration and temperature, whereas a higher content of WTRs results in lower removal efficiency because of the quenching effect and negative effect of high pH. For an initial solution pH of 3 and 5, 94.1% and 87.4% of ATZ degradation can be achieved within 6h, whereas the value is only 26% for pH of 7. The production of sulfate radicals (SO 4 - ) and hydroxyl radicals (OH) was confirmed by classic radical quenching and electron spin resonance (ESR) tests. Based on the GC-MS and LC-MS results, the main degradation pathways of ATZ may contain dealkylation, dechlorination-hydroxylation, and alkyl chain oxidation processes. In addition to the ATZ removal ability, the WTRs/PMS system can simultaneously remove phosphorus. This article provides a new idea for wastewater treatment and usage of WTRs as a resource. Copyright © 2017 Elsevier B.V. All rights reserved.

  3. Aluminum-based drinking-water treatment residuals: a novel sorbent for perchlorate removal.

    Science.gov (United States)

    Makris, Konstantinos C; Sarkar, Dibyendu; Datta, Rupali

    2006-03-01

    Perchlorate contamination of aquifers and drinking-water supplies has led to stringent regulations in several states to reduce perchlorate concentrations in water at acceptable levels for human consumption. Several perchlorate treatment technologies exist, but there is significant cost associated with their use, and the majority of them are unable to degrade perchlorate to innocuous chloride. We propose the use of a novel sorbent for perchlorate, i.e. an aluminum-based drinking-water treatment residual (Al-WTR), which is a by-product of the drinking-water treatment process. Perchlorate sorption isotherms (23+/-1 degrees C) showed that the greatest amount (65%) of perchlorate removed by the Al-WTR was observed with the lowest initial perchlorate load (10 mg L(-1)) after only 2 h of contact time. Increasing the contact time to 24 h, perchlorate removal increased from 65 to 76%. A significant correlation was observed between the amounts of perchlorate removed with evolved chloride in solution, suggesting degradation of perchlorate to chloride.

  4. Intermittent hormonal therapy in the treatment of post-irradiation residual/recurrent prostate cancer

    International Nuclear Information System (INIS)

    Williams, Aaron O; Kocherill, Paul G; Wallace, Michelle; Forman, Jeffrey D

    1996-01-01

    Purpose: To evaluate the efficacy and toxicity of intermittent hormonal therapy in the treatment of residual/recurrent prostate cancer. Materials and Methods: Seventeen patients with biochemical evidence of residual/recurrent prostate cancer were initially treated with radiation therapy (RT)(13), neo-adjuvant hormonal therapy and RT (3), or RT following prostatectomy (1). The mean follow-up time was 19.4 months from the initiation of hormonal therapy. Hormonal therapy consisted of an LH-RH agonist alone (7), an anti-androgen alone (1) or a combination of both (9). Hormonal therapy was continued until the prostatic specific antigen (PSA) level became undetectable. IHT was reinstituted when the PSA reached a pre-determined level, usually greater than or equal to 10ng/ml. Results: The mean time from completion of primary treatment to the initiation of hormonal therapy was 32.5 months. The mean PSA at the start of the first cycle of hormonal therapy was 43.9ng/ml, the second cycle, 11.9ng/ml and the third cycle, 24ng/ml. The mean PSA levels at the end of the first and second cycle of hormonal therapy were .48 and .42ng/ml, respectively. No patient has yet completed the third cycle of hormonal therapy. The average duration of hormonal therapy was 10 months for the first cycle and 4 months for the second cycle. The mean intermittent time off hormones were 9.3 months between cycles 1 and 2, and 10 months between cycles 2 and 3. No patient has yet become refractory to hormonal therapy. Currently all patients are alive. All patients experienced hot flashes and decreased libido at varying degrees during treatment. Thirty-five percent experienced gynecomastia. During the intervals between hormonal therapy, most patients reported a decrease in hot flashes. Conclusion: This analysis supplies preliminary evidence that intermittent hormonal therapy is a viable option in patients with biochemical evidence of disease following initial therapy. It is associated with less treatment

  5. On-site treatment and landfilling of MSWI air pollution control residues

    DEFF Research Database (Denmark)

    Lundtorp, Kasper; Jensen, Dorthe Lærke; Sørensen, Mette Abildgaard

    2003-01-01

    Air pollution control (APC) residues from municipal solid waste incineration (MSWI) are difficult to landfill due to substantial leaching of trace metals. An on-site pretreatment prior to landfilling of APC-residues was investigated in terms of bench-scale experiments with a semidry APC-residue a......Air pollution control (APC) residues from municipal solid waste incineration (MSWI) are difficult to landfill due to substantial leaching of trace metals. An on-site pretreatment prior to landfilling of APC-residues was investigated in terms of bench-scale experiments with a semidry APC...

  6. Coal Combustion Wastes Reuse in Low Energy Artificial Aggregates Manufacturing

    OpenAIRE

    Ferone, Claudio; Colangelo, Francesco; Messina, Francesco; Iucolano, Fabio; Liguori, Barbara; Cioffi, Raffaele

    2013-01-01

    Sustainable building material design relies mostly on energy saving processes, decrease of raw materials consumption, and increase of waste and by-products recycling. Natural and lightweight artificial aggregates production implies relevant environmental impact. This paper addresses both the issues of residues recycling and energy optimization. Particularly, three coal combustion wastes (Weathered Fly Ash, WFA; Wastewater Treatment Sludge, WTS; Desulfurization Device Sludge, DDS) supplied by ...

  7. Combustion engineering

    CERN Document Server

    Ragland, Kenneth W

    2011-01-01

    Introduction to Combustion Engineering The Nature of Combustion Combustion Emissions Global Climate Change Sustainability World Energy Production Structure of the Book   Section I: Basic Concepts Fuels Gaseous Fuels Liquid Fuels Solid Fuels Problems Thermodynamics of Combustion Review of First Law Concepts Properties of Mixtures Combustion StoichiometryChemical EnergyChemical EquilibriumAdiabatic Flame TemperatureChemical Kinetics of CombustionElementary ReactionsChain ReactionsGlobal ReactionsNitric Oxide KineticsReactions at a Solid SurfaceProblemsReferences  Section II: Combustion of Gaseous and Vaporized FuelsFlamesLaminar Premixed FlamesLaminar Flame TheoryTurbulent Premixed FlamesExplosion LimitsDiffusion FlamesGas-Fired Furnaces and BoilersEnergy Balance and EfficiencyFuel SubstitutionResidential Gas BurnersIndustrial Gas BurnersUtility Gas BurnersLow Swirl Gas BurnersPremixed-Charge Engine CombustionIntroduction to the Spark Ignition EngineEngine EfficiencyOne-Zone Model of Combustion in a Piston-...

  8. Evaluation of Residual Stress Measurements Before and After Post-Weld Heat Treatment in the Weld Repairs

    Science.gov (United States)

    Pardowska, Anna M.; Price, John W. H.; Finlayson, Trevor R.; Ibrahim, R.

    2010-11-01

    Welding repairs are increasingly a structural integrity concern for aging pressure vessel and piping components. It has been demonstrated that the residual stress distribution near repair welds can be drastically different from that of the original weld. Residual stresses have a significant effect on the lifetime performance of a weld, and a reduction of these stresses is normally desirable. The aim of this paper is to investigate residual stresses in various weld repair arrangements using the non-destructive neutron diffraction technique. This research is focused on characterization of the residual stress distribution: (i) in the original weld; (ii) in a shallow toe weld repair; and (iii) after conventional post-weld heat treatment. The focus of the measurements is on the values of the subsurface strain/stress variations across the weld.

  9. Efficacy of surgical techniques and factors affecting residual stone rate in the treatment of kidney stones.

    Science.gov (United States)

    Aydemir, Hüseyin; Budak, Salih; Kumsar, Şükrü; Köse, Osman; Sağlam, Hasan Salih; Adsan, Öztuğ

    2014-09-01

    In this study, we aimed to evaluate, the efficacy of surgical methods and the factors affecting the residual stone rate by scrutinizing retrospectively the patients who had undergone renal stone surgery. Records of 109 cases of kidney stones who had been surgically treated between January 2010, and July 2013 were reviewed. Patients were divided into three groups in terms of surgical treatment; open stone surgery, percutaneous nephrolithotomy (PNL) and retrograde intrarenal surgery (RIRS). Patients' history, physical examination, biochemical and radiological images and operative and postoperative data were recorded. The patients had undergone PNL (n=74; 67.9%), RIRS (n=22;20.2%), and open renal surgery (n=13; 11.9%). The mean and median ages of the patients were 46±9, 41 (21-75) and, 42 (23-67) years, respectively. The mean stone burden was 2.6±0.7 cm(2) in the PNL, 1.4±0.1 cm(2) in the RIRS, and 3.1±0.9 cm(2) in the open surgery groups. The mean operative times were 126±24 min in the PNL group, 72±12 min in the RIRS group and 82±22 min in the open surgery group. The duration of hospitalisation was 3.1±0.2 days, 1.2±0.3 days and 3.4±1.1 days respectively. While the RIRS group did not need blood transfusion, in the PNL group blood transfusions were given in the PNL (n=18), and open surgery (n=2) groups. Residual stones were detected in the PNL (n=22), open surgery (n=2), and RIRS (n=5) groups. PNL and RIRS have been seen as safe and effective methods in our self application too. However, it should not be forgotten that as a basical method, open surgery may be needed in cases of necessity.

  10. Granulation of drinking water treatment residuals as applicable media for phosphorus removal.

    Science.gov (United States)

    Li, Xiuqing; Cui, Jun; Pei, Yuansheng

    2018-02-22

    Recycling drinking water treatment residuals (DWTR) show promise as a strategy for phosphorus (P) removal; however, powdered DWTR is not an ideal practical medium due to clogging. This study granulates DWTR by entrapping powdered DWTR in alginate beads. Results show that granular DWTR has an appreciable amount of mesopores along with a Brunauer-Emmett-Teller (BET) surface area of 43.8 m 2 /g and total pore volume of 0.049 cm 3 /g. Most metals (e.g., Al, Ba, Be, Cd, Co, Cr, Mn, Ni, Pb, and Zn) in granular DWTR became more stable and granular DWTR could be considered non-hazardous material. Further analysis indicates that the granular DWTR has strong P adsorption capability with a maximum adsorption capacity of 19.70 mg/g as estimated by the Langmuir model. Good P adsorption may be attributed to the formation of Fe-PO 4 and Al-PO 4 associated with the amorphous state of enormous iron and aluminum in granular DWTR. More importantly, granular DWTR exhibits good mechanical stability and maintained its shape with weight loss below 12.49% after three recycling rounds. Overall, granular DWTR appears to serve as better media for phosphorus removal in water treatment structures such as wetlands. Copyright © 2018 Elsevier Ltd. All rights reserved.

  11. Electrodialytic treatment for metal removal from sewage sludge ash from fluidized bed combustion

    DEFF Research Database (Denmark)

    Pazos, Marta; Kirkelund, Gunvor Marie; Ottosen, Lisbeth M.

    2010-01-01

    Sewage sludge contains several potentially hazardous compounds such as heavy metals, PCBs, PAHs, etc. However, elements with high agricultural value (P, K or Ca) are also present. During the last years, the fluidized bed sludge combustor (FBSC) is considered an effective and novel alternative...... of electrodialytic treatment, the Cd concentration was reduced to values below the limiting concentration. In all experiments the concentrations of other metals were under limiting values of the Danish legislation. It can be concluded that the electrodialytic treatment is an adequate alternative to reduce the Cd...

  12. Sewage sludge as additive to reduce the initial fireside corrosion caused by combustion of shredder residues in a waste-fired BFB boiler

    Energy Technology Data Exchange (ETDEWEB)

    Jonsson, T.; Pettersson, J.; Johansson, L.G.; Svensson, J.E. [Chalmers Univ. of Technology, Goeteborg (Sweden). Environmental Inorganic Chemistry; Davidsson, K. [SP Technical Research Institute of Sweden, Boraas (Sweden)

    2010-07-01

    Corrosion/deposition field tests have been carried out in a commercial waste-fired BFB boiler using air-cooled probes. The influence of 20% shredder light fraction (SLF), from recovery of metal scrap material, mixed with waste was studied at different material temperatures (280-420 C). In addition, 3% sewage sludge was added to the 20% SLF/waste mixture. The initial deposit and corrosion products were compared to when the normal waste (municipal solid waste and industrial wastes) fuel was used. After 24 hours exposure, the deposits were analyzed as for elemental composition while the corrosion products were characterised by ESEM/EDX and XRD. The results show that combustion of 20% SLF increased the amount of deposition, which in addition contains a larger fraction chlorine. This causes a higher initial corrosion rate. Adding 3% sewage sludge removes the effect of the SLF and deposits and corrosion products were comparable with the ones formed during the reference exposure. The results indicate that the initial fireside corrosion is chlorine induced and no signs of low-melting heavy metals salts were observed in the corrosion products. (orig.)

  13. A randomised controlled trial on the effect of mask choice on residual respiratory events with continuous positive airway pressure treatment.

    Science.gov (United States)

    Ebben, Matthew R; Narizhnaya, Mariya; Segal, Alan Z; Barone, Daniel; Krieger, Ana C

    2014-06-01

    It has been found that mask style can affect the amount of continuous positive airway pressure (CPAP) required to reduce an apnoea/hyponoea index (AHI) to mask style to another post titration could affect the residual AHI with CPAP. The purpose of this study was to investigate the differences in residual AHI with CPAP treatment between oronasal and nasal masks. Twenty-one subjects (age mean (M)=62.9, body mass index (BMI) M=29.6 kg/m2) were randomised (14 subjects completed the protocol) to undergo an in-laboratory CPAP titration with either a nasal mask or an oronasal mask. Subjects were then assigned this mask for 3weeks of at-home CPAP use with the optimal treatment pressure determined on the laboratory study (CPAP M=8.4 cm of H2O). At the end of this 3-week period, data were collected from the CPAP machine and the subject was given the other mask to use with the same CPAP settings for the next 3weeks at home (if the nasal mask was given initially, the oronasal one was given later and vice versa). On completion of the second 3-week period, data on residual AHI were again collected and compared with the first 3-week period on CPAP. A Wilcoxon Signed-Rank Test (two-tailed) revealed that residual AHI with CPAP treatment was significantly higher with the oronasal compared with the nasal mask (z = -3.296, pmask, and 50% of the subjects had a residual AHI >10/h in the oronasal mask condition, even though all of these subjects were titrated to an AHI of mask compared with a nasal mask. Switching to an oronasal mask post titration results in an increase in residual AHI with CPAP treatment, and pressure adjustment may be warranted. Copyright © 2014 Elsevier B.V. All rights reserved.

  14. Prediction and measurement of relieved residual stress by the cryogenic heat treatment for Al6061 alloy: mechanical properties and microstructure

    International Nuclear Information System (INIS)

    Ko, Dae Hoon; Ko, Dae Cheol; Kim, Byung Min; Lim, Hak Jin; Lee, Jung Min

    2013-01-01

    The purpose of this study is to predict the residual stress resulting from the cryogenic heat treatment (CHT) which affects the mechanical properties and microstructure for Al6061 alloy. The CHT is very effective method to reduce the residual stress by quenching media such as liquid nitrogen, boiling water and steam. In this study, experimental T6 and CHT are carried out to measure the temperature of Al parts and to determine the convective heat transfer coefficient. This coefficient is used to predict the residual stress during FE-simulation. In order to consider the relaxation of residual stress during artificial ageing, the Zener-Wert-Avrami function with elasto-plastic nonlinear analysis is used in this study. The predicted residual stress is compared with the measured one by X-ray diffraction (XRD) and is found to be in good agreement with results of the FE-simulation. Further, after T6 and CHT, the electrical conductivity and hardness of the Al6061 alloy are measured to estimate the mechanical properties and its microstructure such as precipitates is observed by Transmission electron microscopy (TEM). Also, the creation of precipitates during T6 and CHT are verified by XRD with component analysis. It is found that CHT affects the residual stress, mechanical properties, and precipitation of the Al 6061 alloy.

  15. Laboratory scale electron beam system for treatment of flue gases from diesel combustion

    International Nuclear Information System (INIS)

    Siti Aiasah Hashim; Khairul Zaman Mohd Dahlan; Khomsaton Abu Bakar; Ayub Muhammad

    2004-01-01

    Laboratory scale test rig to treat simulated flue gas using electron beam technology was installed at the Alurtron EB-Irradiation Center, MINT. The experiment test rig was proposed as a result of feasibility studies conducted jointly by IAEA, MINT and TNB Research in 1997. The test rig system consists of several components, among other, diesel generator sets, pipe ducts, spray cooler, ammonia dosage system, irradiation vessel, bag filter and gas analyzers. The installation was completed and commissioned in October 2001. results from the commissioning test runs and subsequent experimental work showed that the efficiency of flue gas treatment is high. It was proven that electron beam technology might be applied in the treatment of air pollutants. This paper describes the design and work function of the individual major components as well as the full system function. Results from the initial experimental works are also presented. (Author)

  16. Effect of weathering transformations of coal combustion residuals on trace element mobility in view of the environmental safety and sustainability of their disposal and use. I. Hydrogeochemical processes controlling pH and phase stability.

    Science.gov (United States)

    Stefaniak, Sebastian; Miszczak, Ewa; Szczepańska-Plewa, Jadwiga; Twardowska, Irena

    2015-06-01

    Coal combustion residuals (CCRs) are one of the most abundant high-volume waste materials disposed in impoundments worldwide. Some methods of CCR recycling, e.g. their use as structural fill for low lying areas or as soil amendment, also expose this material to atmospheric conditions. Combustion processes result in concentration of trace elements in CCRs at about an order of magnitude compared to coal. In order to assess an effect of long-term weathering transformations of CCRs on trace element binding/release, a study has been carried out. It is based on the chemical composition of real pore solutions extracted from the most abundant primary alkaline Class F bituminous CCRs, 0 to >40 years old, sampled from the surface layer and vertical profiles at four different impoundments. In this part of the study, results of a hydrogeochemical simulation of the saturation state of real pore solutions with respect to mineral phases of CCRs with use of the PHREEQC program, related to actual pH values reflecting the full cycle of weathering transformations, have been discussed. This study is the first geochemical proof of the general trend towards a progressive acidification up to pH < 4 of primary alkaline CCRs due to release of protons during internal processes of formation of gibbsite and aluminosilicate minerals, buffered by carbonates at the alkaline - near-neutral stages, and followed by parallel dissolution and buffering by aluminosilicates at pH < 7 after carbonate depletion, to the level up to pH∼3.5-4.0. The intrinsic geochemical changes have resulted in the different susceptibility of trace elements to release and associated changes in risk to the environment at consecutive stages of weathering. Copyright © 2015 Elsevier Ltd. All rights reserved.

  17. Biogas utilization as flammable for internal combustion engine

    International Nuclear Information System (INIS)

    Cardenas, H.

    1995-01-01

    In this work the energetic potential stored in form of generated biogas of organic industrial wastes treatment is analyzed. Biogas utilization as flammable at internal combustion engine coupled to electrical energy generating is studied in the Wastewater Treatment Plant of Bucaramanga city (Colombia). This Plant was designed for 160.000 habitants treatment capacity, 1300 m3/h wealth, 170 BDO/m3 residues concentration and 87% process efficiency. The plant generate 2.000 m3/d of biogas. In laboratory trials was worked with biogas originating from Treatment Plant, both without purifying and purified, and the obtained results were compared with both yields determined with 86-octanes gasoline and natural gas. The analysis of pollutant by-products generated in combustion process as leak gases, present corrosive compounds and not desirable. elements in biogas composition are included

  18. Illegal treatment of barrows with nandrolone ester: effect on growth, histology and residue levels in urine and hair

    NARCIS (Netherlands)

    Groot, M.J.; Lasaroms, J.J.P.; Bennekom, van E.O.; Meijer, T.; Vinyeta, E.; Klis, van der J.D.; Nielen, M.W.F.

    2012-01-01

    The effect of 17ß-19-nortestosterone (17ßNT) treatment of barrows on residue levels and growth was evaluated. Five barrows were treated three times during the fattening period with 17ßNT phenylpropionate (Nandrosol, nandrolone phenylpropionate 50¿mg/ml,1¿mg/kg body weight). Another five barrows were

  19. Ractopamine residues in urine, plasma and hair of cattle during and after treatment.

    Science.gov (United States)

    Tang, Chaohua; Zhang, Junmin; Li, Lijun; Zhao, Qingyu; Bu, Dengpan

    2014-04-01

    The objective of this study was to investigate ractopamine residues in urine, plasma and hair of cattle during and after treatment. Three cattle (body weight = 620 ± 6.2 kg) were administered ractopamine (2.01 mg/kg body weight) into the rumen for 5 consecutive days. Ractopamine concentrations in samples were determined by an ultra-performance liquid chromatography-tandem mass spectrometry (UPLC-MS-MS) method. The concentrations of parent ractopamine in urine were 1,631.1 ng/mL on withdrawal day 0 and 8.3 ng/mL on withdrawal day 14. After hydrolysis of its conjugates, ractopamine concentration ranged from 11,796.7 ng/mL (withdrawal day 0) to 39.7 ng/mL (withdrawal day 14). In plasma, parent ractopamine and its conjugates were below the limits of quantification (LOQ = 0.2 ng/mL) on withdrawal days 5 and 7. Accumulation of ractopamine in black and white hair was 124.6 and 78.1 ng/g, respectively, on withdrawal day 0, and 226.7 and 165.6 ng/g, respectively, on withdrawal day 14. This study demonstrated the rapid elimination and high bioavailability of ractopamine in urine and plasma in cattle. However, accumulation of ractopamine in cattle's hair is high and persistent, so hair can be used as the target matrix for monitoring ractopamine abuse in ruminants.

  20. Surface arsenic speciation of a drinking-water treatment residual using X-ray absorption spectroscopy.

    Science.gov (United States)

    Makris, Konstantinos C; Sarkar, Dibyendu; Parsons, Jason G; Datta, Rupali; Gardea-Torresdey, Jorge L

    2007-07-15

    Drinking-water treatment residuals (WTRs) present a low-cost geosorbent for As-contaminated waters and soils. Previous work has demonstrated the high affinity of WTRs for As, but data pertaining to the stability of sorbed As is missing. Sorption/desorption and X-ray absorption spectroscopy (XAS), both XANES (X-ray absorption near edge structure) and EXAFS (extended X-ray absorption fine structure) studies, were combined to determine the stability of As sorbed by an Fe-based WTR. Arsenic(V) and As(III) sorption kinetics were biphasic in nature, sorbing >90% of the initial added As (15,000 mg kg(-1)) after 48 h of reaction. Subsequent desorption experiments with a high P load (7500 mg kg(-1)) showed negligible As desorption for both As species, approximately <3.5% of sorbed As; the small amount of desorbed As was attributed to the abundance of sorption sites. XANES data showed that sorption kinetics for either As(III) or As(V) initially added to solution had no effect on the sorbed As oxidation state. EXAFS spectroscopy suggested that As added either as As(III) or as As(V) formed inner-sphere mononuclear, bidentate complexes, suggesting the stability of the sorbed As, which was further corroborated by the minimum As desorption from the Fe-WTR.

  1. Ecotoxicological assessment of dewatered drinking water treatment residue for environmental recycling.

    Science.gov (United States)

    Yuan, Nannan; Wang, Changhui; Wendling, Laura A; Pei, Yuansheng

    2017-09-01

    The beneficial recycle of drinking water treatment residue (DWTR) in environmental remediation has been demonstrated in many reports. However, the lack of information concerning the potential toxicity of dewatered DWTR hinders its widespread use. The present study examined the ecotoxicity of dewatered aluminum (Al) and iron (Fe) DWTR leachates to a green alga, Chlorella vulgaris. Data from the variations of cell density and chlorophyll a content suggested that algal growth in DWTR leachates was inhibited. The algal cellular oxidation stress was initially induced but completely eliminated within 72 h by antioxidant enzymes. The expression of three photosynthesis-related algae genes (psaB, psbC, and rbcL) also temporarily decreased (within 72 h). Moreover, the algal cells showed intact cytomembranes after exposure to DWTR leachates. Further investigation confirmed that inhibition of algal growth was due to DWTR-induced phosphorus (P) deficiency in growth medium, rather than potentially toxic contaminants (e.g. copper and Al) contained in DWTR. Interestingly, the leachates could potentially promote algal growth via increasing the supply of new components (e.g. calcium, kalium, magnesium, and ammonia nitrogen) from DWTR. In summary, based on the algae toxicity test, the dewatered Fe/Al DWTR was nontoxic and its environment recycling does not represent an ecotoxicological risk to algae.

  2. Aluminum drinking water treatment residuals (Al-WTRs) as sorbent for mercury: Implications for soil remediation.

    Science.gov (United States)

    Hovsepyan, Anna; Bonzongo, Jean-Claude J

    2009-05-15

    The potential of readily available and non-hazardous waste material, aluminum drinking water treatment residuals (Al-WTRs), to efficiently sorb and immobilize mercury (Hg) from aqueous solutions was evaluated. Al-WTR samples with average specific surface area of 48m(2)/g and internal micropore surface area of 120m(2)/g were used in a series of batch sorption experiments. Obtained sorption isotherms indicated a strong affinity of Hg for Al-WTRs. Using the Langmuir adsorption model, a relatively high maximum sorption capacity of 79mg Hg/g Al-WTRs was determined. Sorption kinetic data was best fit to a pseudo-first-order model, while the use of the Weber-Morris and Bangham models suggested that the intraparticle diffusion could be the rate-limiting step. Also, Al-WTRs effectively immoblized Hg in the pH range of 3-8. The results from these short-term experiments demonstrate that Al-WTRs can be effectively used to remove Hg from aqueous solutions. This ability points to the potential of Al-WTRs as a sorbent in soil remediation techniques based on Hg-immobilization.

  3. Comparison of metals extractability from Al/Fe-based drinking water treatment residuals.

    Science.gov (United States)

    Wang, Changhui; Bai, Leilei; Pei, Yuansheng; Wendling, Laura A

    2014-12-01

    Recycling of drinking water treatment residuals (WTRs) as environment amendments has attracted substantial interest due to their productive reuse concomitant with waste minimization. In the present study, the extractability of metals within six Al/Fe-hydroxide-comprised WTRs collected throughout China was investigated using fractionation, in vitro digestion and the toxicity characteristic leaching procedure (TCLP). The results suggested that the major components and structure of the WTRs investigated were similar. The WTRs were enriched in Al, Fe, Ca, and Mg, also contained varying quantities of As, Ba, Be, Cd, Co, Cr, Cu, K, Mn, Mo, Na, Ni, Pb, Sr, V, and Zn, but Ag, Hg, Sb, and Se were not detected. Most of the metals within the WTRs were largely non-extractable using the European Community Bureau of Reference (BCR) procedure, but many metals exhibited high bioaccessibility based on in vitro digestion. However, the WTRs could be classified as non-hazardous according to the TCLP assessment method used by the US Environmental Protection Agency (USEPA). Further analysis showed the communication factor, which is calculated as the ratio of total extractable metal by BCR procedure to the total metal, for most metals in the six WTRs, was similar, whereas the factor for Ba, Mn, Sr, and Zn varied substantially. Moreover, metals in the WTRs investigated had different risk assessment code. In summary, recycling of WTRs is subject to regulation based on assessment of risk due to metals prior to practical application.

  4. Coal combustion ashes: A radioactive Waste?

    International Nuclear Information System (INIS)

    Michetti, F.P.; Tocci, M.

    1992-01-01

    The radioactive substances naturally hold in fossil fuels, such as Uranium and Thorium, after the combustion, are subjected to an increase of concentration in the residual combustion products as flying ashes or as firebox ashes. A significant percentage of the waste should be classified as radioactive waste, while the political strategies seems to be setted to declassify it as non-radioactive waste. (Author)

  5. Development of an efficient process for the treatment of residual sludge discharged from an anaerobic digester in a sewage treatment plant.

    Science.gov (United States)

    Abe, Naoki; Tang, Yue-Qin; Iwamura, Makoto; Ohta, Hiroto; Morimura, Shigeru; Kida, Kenji

    2011-09-01

    In order to reduce the discharge of residual sludge from an anaerobic digester, pre-treatment methods including low-pressure wet-oxidation, Fenton oxidation, alkali treatment, ozone oxidation, mechanical destruction and enzymatic treatment were evaluated and compared. VSS removal efficiencies of greater than 50% were achieved in cases of low-pressure wet-oxidation, Fenton oxidation and alkali treatment. Residual sludge from an anaerobic digester was pre-treated and subjected to thermophilic anaerobic digestion. As a result, the process of low-pressure wet-oxidation followed by anaerobic digestion achieved the highest VSS removal efficiency of 83%. The total efficiency of VSS removal of sewage sludge consisting of primary and surplus sludge would be approximately 92%, assuming that the VSS removal efficiency of sewage sludge is 50% in the anaerobic digester of the sewage treatment plant. Copyright © 2011 Elsevier Ltd. All rights reserved.

  6. Neutron diffraction measurements for the determination of heat treatment effectiveness in generating compressive residual stress in an automotive crown gear

    International Nuclear Information System (INIS)

    Albertini, G.; Fiori, F.; Girardin, E.; Giuliani, A.; Pyzalla, A.; Quadrini, E.

    1999-01-01

    Complete text of publication follows. Thermal austenitizing and tempering treatments are being developed in automotive industry to prevent crack initiation and avoid crack propagation, especially in components where stress intensity factors influence the stress field and then the fatigue life of the component itself. This is the case of crown gears, where the teeth root undergoes frequently to cracking when tensile residual stresses are present at the surface, as typical loads are impulsive and very high. The sign reversal of these stresses is the aim of austenitizing and tempering treatments. In this work residual stress measurements carried out at HMI-BENSC are presented, in a UNI55Cr3 steel crown gear submitted to such kind of treatments, performed with a new multi-frequency induction technique whose effectiveness is checked. (author)

  7. A Regulator's Guide to Management of Radioactive Residuals from Drinking Water Treatment Technologies

    Science.gov (United States)

    This guide is intended for state regulators, technical assistance providers, and field staffto help states address radionuclide residual disposal by outlining options available to help systems address elevated radionuclide levels.

  8. Bundling of harvesting residues and whole-trees and the treatment of bundles; Hakkuutaehteiden ja kokopuiden niputus ja nippujen kaesittely

    Energy Technology Data Exchange (ETDEWEB)

    Kaipainen, H.; Seppaenen, V.; Rinne, S.

    1996-12-31

    The conditions on which the bundling of the harvesting residues from spruce regeneration fellings would become profitable were studied. The calculations showed that one of the most important features was sufficient compaction of the bundle, so that the portion of the wood in the unit volume of the bundle has to be more than 40 %. The tests showed that the timber grab loader of farm tractor was insufficient for production of dense bundles. The feeding and compression device of the prototype bundler was constructed in the research and with this device the required density was obtained.The rate of compaction of the dry spruce felling residues was about 40 % and that of the fresh residues was more than 50 %. The comparison between the bundles showed that the calorific value of the fresh bundle per unit volume was nearly 30 % higher than that of the dry bundle. This means that the treatment of the bundles should be done of fresh felling residues. Drying of the bundles succeeded well, and the crushing and chipping tests showed that the processing of the bundles at the plant is possible. The treatability of the bundles was also excellent. By using the prototype, developed in the research, it was possible to produce a bundle of the fresh spruce harvesting residues, the diameter of which was about 50 cm and the length about 3 m, and the rate of compaction over 50 %. By these values the reduction target of the costs is obtainable

  9. Drying of residue and separation of nitrate salts in the sludge waste for the lagoon sludge treatment

    International Nuclear Information System (INIS)

    Hwang, D. S.; Lee, K. I.; Choi, Y. D.; Hwang, S. T.; Park, J. H.

    2003-01-01

    This study investigated the dissolution property of nitrate salts in the dissolution process by water and the drying property of residue after separating nitrates in a series of the processes for the sludge treatment. Desalination was carried out with the adding ratio of water and drying property was analyzed by TG/DTA, FTIR, and XRD. Nitrate salts involved in the sludge were separated over 97% at the water adding ratio of 2.5. But a small quantity of calcium and sodium nitrate remained in the residue These were decomposed over 600 .deg. C and calcium carbonate, which was consisted mainly of residue, was decomposed into calcium oxide over 750 .deg. C. The residue have to be decomposed over 800 .deg. C to converse uranyl nitrate of six value into the stable U 3 O 8 of four value. As a result of removing the nitrates at the water adding ratio of 2.5 and drying the residue over 900 .deg. C, volume of the sludge waste decreased over 80%

  10. Evolution of Residual Stress and Distortion of Cold-Rolled Bearing Ring from Annealing to Quenched-Tempered Heat Treatment

    Science.gov (United States)

    Lu, Bohan; Lu, Xiaohui

    2018-02-01

    This study investigates the correlation between the residual stress and distortion behavior of a cold-rolled ring from the annealing to quenching-tempering (QT) process. Due to the cold-rolled process, the external periphery of the bearing ring experiences a compressive residual stress. To relieve the residual stress, cold-rolled rings are annealed at 700 °C which is higher than the starting temperature of recrystallization. When cold-rolled rings are annealed at 700 °C for 15 min, the compressive residual stress is reduced to zero and the outer diameter of the annealed ring becomes larger than that of a non-annealed sample, which is unrelated to annealing time. Simultaneously, the roundness and taper deviation do not obviously change compared with those of non-annealed sample. The stress relaxation during the annealing process was attributed to the recovery and recrystallization of ferrite. Annealing has a genetic influence on the following QT heat treatment, wherein the lowest residual stress is in the non-annealed cold-rolled ring. From the annealing to QT process, the deviation of the outer diameter, roundness, and taper increased with annealing time, a large extend than that of non-annealed samples.

  11. Combustion physics

    Science.gov (United States)

    Jones, A. R.

    1985-11-01

    Over 90% of our energy comes from combustion. By the year 2000 the figure will still be 80%, even allowing for nuclear and alternative energy sources. There are many familiar examples of combustion use, both domestic and industrial. These range from the Bunsen burner to large flares, from small combustion chambers, such as those in car engines, to industrial furnaces for steel manufacture or the generation of megawatts of electricity. There are also fires and explosions. The bountiful energy release from combustion, however, brings its problems, prominent among which are diminishing fuel resources and pollution. Combustion science is directed towards finding ways of improving efficiency and reducing pollution. One may ask, since combustion is a chemical reaction, why physics is involved: the answer is in three parts. First, chemicals cannot react unless they come together. In most flames the fuel and air are initially separate. The chemical reaction in the gas phase is very fast compared with the rate of mixing. Thus, once the fuel and air are mixed the reaction can be considered to occur instantaneously and fluid mechanics limits the rate of burning. Secondly, thermodynamics and heat transfer determine the thermal properties of the combustion products. Heat transfer also plays a role by preheating the reactants and is essential to extracting useful work. Fluid mechanics is relevant if work is to be performed directly, as in a turbine. Finally, physical methods, including electric probes, acoustics, optics, spectroscopy and pyrometry, are used to examine flames. The article is concerned mainly with how physics is used to improve the efficiency of combustion.

  12. Influence of the inherent properties of drinking water treatment residuals on their phosphorus adsorption capacities.

    Science.gov (United States)

    Bai, Leilei; Wang, Changhui; He, Liansheng; Pei, Yuansheng

    2014-12-01

    Batch experiments were conducted to investigate the phosphorus (P) adsorption and desorption on five drinking water treatment residuals (WTRs) collected from different regions in China. The physical and chemical characteristics of the five WTRs were determined. Combined with rotated principal component analysis, multiple regression analysis was used to analyze the relationship between the inherent properties of the WTRs and their P adsorption capacities. The results showed that the maximum P adsorption capacities of the five WTRs calculated using the Langmuir isotherm ranged from 4.17 to 8.20mg/g at a pH of 7 and further increased with a decrease in pH. The statistical analysis revealed that a factor related to Al and 200 mmol/L oxalate-extractable Al (Alox) accounted for 36.5% of the variations in the P adsorption. A similar portion (28.5%) was attributed to an integrated factor related to the pH, Fe, 200 mmol/L oxalate-extractable Fe (Feox), surface area and organic matter (OM) of the WTRs. However, factors related to other properties (Ca, P and 5 mmol/L oxalate-extractable Fe and Al) were rejected. In addition, the quantity of P desorption was limited and had a significant negative correlation with the (Feox+Alox) of the WTRs (p<0.05). Overall, WTRs with high contents of Alox, Feox and OM as well as large surface areas were proposed to be the best choice for P adsorption in practical applications. Copyright © 2014. Published by Elsevier B.V.

  13. Innovative approach for recycling phosphorous from agro-wastewaters using water treatment residuals (WTR).

    Science.gov (United States)

    Zohar, Iris; Ippolito, James A; Massey, Michael S; Litaor, Iggy M

    2017-02-01

    Phosphorus capture from polluting streams and its re-use using industrial byproducts has the potential to also reduce environmental threats. An innovative approach was developed for P removal from soil leachate and dairy wastewater using Al-based water treatment residuals (Al-WTR) to create an organic-Al-WTR composite (Al/O-WTR), potentially capable of serving as a P fertilizer source. Al-WTR was mixed with either soil leachate, or with dairy wastewater, both of which contained elevated P concentrations (e.g., 7.6-43.5 mg SRP L -1 ). The Al-WTR removed ∼95% inorganic P, above 80% organic P, and over 60% dissolved organic carbon (DOC) from the waste streams. P removal was correlated with P concentration in the waste streams and was consistent with an increase in Al/O-WTR P content as determined by X-ray fluorescence (XRF) and surface analysis using scanning electron microscopy-energy dispersive X-ray spectroscopy (SEM-EDS). Organic C was a major constituent in the original Al-WTR (31.4%) and increased by 1% in the Al/O-WTRs. Organic C accumulation on particles surfaces possibly enhanced weak P bonding. Desorption experiments indicated an initial and substantial P release (30 mg SRP kg -1 Al/O-WTR), followed by relatively constant low P solubility (ca. 10 mg kg -1 ). Organic C was continuously released to the solution (over 8000 mg kg -1 ), concomitantly with Ca and other electrolytes, possibly indicating dissolution from inner pores, accounting for the highly porous nature of the Al-WTR, evident by SEM images. The potential of P-loading on Al/O-WTR to promote P recycling should be further studied. Copyright © 2016 Elsevier Ltd. All rights reserved.

  14. Bacterial toxicity assessment of drinking water treatment residue (DWTR) and lake sediment amended with DWTR.

    Science.gov (United States)

    Yuan, Nannan; Wang, Changhui; Pei, Yuansheng

    2016-11-01

    Drinking water treatment residue (DWTR) seems to be very promising for controlling lake sediment pollution. Logically, acquisition of the potential toxicity of DWTR will be beneficial for its applications. In this study, the toxicity of DWTR and sediments amended with DWTR to Aliivibrio fischeri was evaluated based on the Microtox(®) solid and leachate phase assays, in combination with flow cytometry analyses and the kinetic luminescent bacteria test. The results showed that both solid particles and aqueous/organic extracts of DWTR exhibited no toxicity to the bacterial luminescence and growth. The solid particles of DWTR even promoted bacterial luminescence, possibly because DWTR particles could act as a microbial carrier and provide nutrients for bacteria growth. Bacterial toxicity (either luminescence or growth) was observed from the solid phase and aqueous/organic extracts of sediments with or without DWTR addition. Further analysis showed that the solid phase toxicity was determined to be related mainly to the fixation of bacteria to fine particles and/or organic matter, and all of the observed inhibition resulting from aqueous/organic extracts was identified as non-significant. Moreover, DWTR addition not only had no adverse effect on the aqueous/organic extract toxicity of the sediment but also reduced the solid phase toxicity of the sediment. Overall, in practical application, the solid particles, the water-soluble substances transferred to surface water or the organic substances in DWTR had no toxicity or any delayed effect on bacteria in lakes, and DWTR can therefore be considered as a non-hazardous material. Copyright © 2016 Elsevier Ltd. All rights reserved.

  15. On-treatment non-high-density lipoprotein cholesterol, apolipoprotein B, triglycerides, and lipid ratios in relation to residual vascular risk after treatment with potent statin therapy

    DEFF Research Database (Denmark)

    Mora, Samia; Glynn, Robert J; Boekholdt, S Matthijs

    2012-01-01

    The goal of this study was to determine whether residual risk after high-dose statin therapy for primary prevention individuals with reduced levels of low-density lipoprotein cholesterol (LDL-C) is related to on-treatment apolipoprotein B, non-high-density lipoprotein cholesterol (non-HDL-C), tri...

  16. Characterization of residues from thermal treatment of treated wood and extraction of Cu, Cr, As and Zn

    DEFF Research Database (Denmark)

    Ottosen, Lisbeth M.; Pedersen, Anne Juul; Christensen, Iben Vernegren

    2005-01-01

    Thermal treatment of chromated copper arsenate (CCA) impregnated waste wood is a way to utilize the energy resource of the wood and at the same time to reduce the volume of the waste. An issue of concern in relation to the thermal treatment is As emission to the air. Meanwhile, there is still......, that the charcoal contained a high concentration of Zn, probably from paint. Chemical extraction experiments in HNO were conducted with the charcoal and it was found that the order of extraction (in percentage) was Zn > Cu > As > Cr. A SEM/EDX investigation of the mixed ash from combustion showed the presence...... form in a small layer on the surface of some matrix particles indicating condensation of volatile Cu species. Chemical extraction with inorganic acids showed the order of percentages mobilized as: As > Cu > Cr....

  17. Reduction of pesticide residues on fresh vegetables with electrolyzed water treatment.

    Science.gov (United States)

    Hao, Jianxiong; Wuyundalai; Liu, Haijie; Chen, Tianpeng; Zhou, Yanxin; Su, Yi-Cheng; Li, Lite

    2011-05-01

    Degradation of the 3 pesticides (acephate, omethoate, and dimethyl dichloroviny phosphate [DDVP]) by electrolyzed water was investigated. These pesticides were commonly used as broad-spectrum insecticides in pest control and high-residual levels had been detected in vegetables. Our research showed that the electrolyzed oxidizing (EO) water (pH 2.3, available chlorine concentration:70 ppm, oxidation-reduction potential [ORP]: 1170 mV) and the electrolyzed reducing (ER) water (pH 11.6, ORP: -860 mV) can reduce the pesticide residues effectively. Pesticide residues on fresh spinach after 30 min of immersion in electrolyzed water reduced acephate by 74% (EO) and 86% (ER), omethoate by 62% (EO) and 75% (ER), DDVP by 59% (EO) and 46% (ER), respectively. The efficacy of using EO water or ER water was found to be better than that of using tap water or detergent (both were reduced by more than 25%). Besides spinach, the cabbage and leek polluted by DDVP were also investigated and the degradation efficacies were similar to the spinach. Moreover, we found that the residual level of pesticide residue decreased with prolonged immersion time. Using EO or ER water to wash the vegetables did not affect the contents of Vitamin C, which inferred that the applications of EO or ER water to wash the vegetables would not result in loss of nutrition. © 2011 Institute of Food Technologists®

  18. Impact of single annual treatment and four-monthly treatment for hookworm and Ascaris lumbricoides, and factors associated with residual infection among Kenyan school children.

    Science.gov (United States)

    Kepha, Stella; Mwandawiro, Charles S; Anderson, Roy M; Pullan, Rachel L; Nuwaha, Fred; Cano, Jorge; Njenga, Sammy M; Odiere, Maurice R; Allen, Elizabeth; Brooker, Simon J; Nikolay, Birgit

    2017-02-09

    School-based deworming is widely implemented in various countries to reduce the burden of soil-transmitted helminths (STHs), however, the frequency of drug administration varies in different settings. In this study, we compared the impact of a single annual treatment and 4-monthly treatment over a follow-up among Kenyan school children, and investigated the factors associated with residual infection. We performed a secondary analysis of data from a randomized trial investigating whether deworming for STHs alters risk of acquiring malaria. Children received either a single treatment or 4-monthly albendazole treatments were followed longitudinally from February 2014 to October 2014. The relative impact of treatment and factors associated with residual infections were investigated using mixed-effects regression models. Predisposition to infection was assessed based on Spearman's rank and Kendall's Tau correlation coefficients. In the 4-monthly treatment group, the proportion of children infected with hookworm decreased from 59.9 to 5.7%, while Ascaris lumbricoides infections dropped from 55.7 to 6.2%. In the single treatment group, hookworm infections decreased over the same time period from 58.7 to 18.3% (12.6% absolute difference in reduction, 95% CI: 8.9-16.3%), and A. lumbricoides from 56.7 to 23.3% (17.1% absolute difference in reduction, 95% CI: 13.1-21.1%). There was strong evidence for predisposition to both STH types. Residual hookworm infection among children on 4-monthly treatment were associated with male sex and baseline nutritional status, whereas A. lumbricoides infection was associated with individual and school-level infection at baseline, latrine cleanliness at schools. This study found that 4-monthly treatment w more effective than single annual treatment. Repeated treatments led to dramatic reductions in the intensities of STHs, but did not completely clear infections among school children in Kenya, a presumed reflection of reinfection in a setting

  19. Quantification of heavy metals from residual waste and ashes from the treatment plant of residual water Reciclagua and,effects for the health of those workers which manipulate those residuals

    International Nuclear Information System (INIS)

    Guerrero D, J.J.

    2004-01-01

    In this work, the technique of leaching using thermostatted column in series is applied, the X-ray diffraction for the identification of the atomic and molecular structure of the toxic metals that are present in the residual muds of the water treatment plant located in the municipality of Lerma Estado de Mexico, named RECICLAGUA, likewise the technique is used of emission spectrometry for plasma and X-ray fluorescence for the qualitative analysis. Its were take samples of residual mud and of incinerated mud of the treatment plant of residual waters of the industrial corridor Toluca -Lerma RECICLAGUA, located in Lerma Estado de Mexico. For this study there were mixed 100 g of residual mud with a solution to 10% of mineral acid or sodium hydroxide according to the case, to adjust the one pH at 2, 5, 7 and 10, it was added bisulfite, of 0.3-1.5 g of dodecyl sulfate sodium and 3.939 of DTPA (triple V) (Diethylene triamine pentaacetate). To this mud and ashes were extracted the toxic and valuable metals by means of the leaching technique using thermostatted columns placed in series that were designed by the Dr. Jaime Vite Torres; it is necessary to make mention that so much the process as the equipment with those that work it was patented by the same one. With the extraction of these metals benefits are obtained, mainly of economic type, achieving the decrease of the volume of those wastes that have been generated; as well as the so much the use of those residuals, once the metals have been eliminated, as of those liquors where the metals were extracted. It was carried out a quantitative analysis using emission spectrometry by plasma in solids by this way to be able to know the content of the present metals in the sample before and later of leaching them, these results reported a great quantity of elements. Another of the techniques employees was the X-ray diffraction analysis that provides an elementary content of the samples, identifying elements that are present in

  20. Ultrafiltration in laxative treatment of urban solid residues dump. Experience in the Deposito Controlado de Puigpalter (Girona, Spain)

    International Nuclear Information System (INIS)

    2010-01-01

    The appearance of lixiviates owes fundamentally to the degradation of the organic matter present in the solid residues of dump and his dragging for rain water percolated. These liquids are characterized by high concentrations of organic pollutants, ammonia nitrogen, metallic ions and other potentially toxic substances. Several technologies for lixiviates treatment are used in Deposito Controlado de Puigpalter (Girona), like ultrafiltration, which has demonstrated his efficiency and reliability during the first 12 months of exploitation. (Author)

  1. Aluminum-based water treatment residual use in a constructed wetland for capturing urban runoff phosphorus: Column study

    Science.gov (United States)

    Aluminum-based water treatment residuals (Al-WTR) have a strong affinity to sorb phosphorus. In a proof-of-concept greenhouse column study, Al-WTR was surface-applied at 0, 62, 124, and 248 Mg/ha to 15 cm of soil on top of 46 cm of sand; Al-WTR rates were estimated to capture 0, 10, 20, and 40 year...

  2. Decrease of Pirimiphos-Methyl and Deltamethrin Residues in Stored Rice with Post-Harvest Treatment

    Science.gov (United States)

    Yu, Chuanshan; Li, Yanjie; Zhang, Qian; Zou, Nan; Gu, Kejia; Li, Xuesheng; Pan, Canping

    2014-01-01

    A modified quick, easy, cheap, effective, rugged (QuEChERS) method with multi-walled carbon nanotubes (MWCNTs) as reversed-dispersive solid phase extraction (r-DSPE) material was applied to the analysis of pirimiphos-methyl and deltamethrin residues in stored rice. Two dustable powder (DP) formulations (2% pirimiphos-methyl and deltamethrin DP; 5% pirimiphos-methyl DP) were applied in simulated storehouse trials in the lab. The residues and dissipation of the two pesticides in stored rice were investigated. Slow dissipation of both pesticides was observed in stored rice. The half-lives of pirimiphos-methyl were 23.9–28.9 days, and those of deltamethrin were 23.9–24.8 days. Residues of pirimiphos-methyl from application rates of 4.5–6.75 a.i. mg/kg (active ingredient milligram per kilogram) and 10–15 a.i. mg/kg were 1.6–3.8 mg/kg and 3.0–4.5 mg/kg at 60 days Pre-harvest Interval (PHI). Residues of deltamethrin from an application rate of 0.5–0.75 a.i. mg/kg were 0.13–0.14 mg/kg at 60 days PHI. Both pesticides residues were below the Maximum Residue Limits (MRLs) established by the Codex Alimentarius Commission (CAC). Therefore, at the recommended dosages they are safe for use on stored rice. PMID:24840352

  3. Decrease of Pirimiphos-Methyl and Deltamethrin Residues in Stored Rice with Post-Harvest Treatment

    Directory of Open Access Journals (Sweden)

    Chuanshan Yu

    2014-05-01

    Full Text Available A modified quick, easy, cheap, effective, rugged (QuEChERS method with multi-walled carbon nanotubes (MWCNTs as reversed-dispersive solid phase extraction (r-DSPE material was applied to the analysis of pirimiphos-methyl and deltamethrin residues in stored rice. Two dustable powder (DP formulations (2% pirimiphos-methyl and deltamethrin DP; 5% pirimiphos-methyl DP were applied in simulated storehouse trials in the lab. The residues and dissipation of the two pesticides in stored rice were investigated. Slow dissipation of both pesticides was observed in stored rice. The half-lives of pirimiphos-methyl were 23.9–28.9 days, and those of deltamethrin were 23.9–24.8 days. Residues of pirimiphos-methyl from application rates of 4.5–6.75 a.i. mg/kg (active ingredient milligram per kilogram and 10–15 a.i. mg/kg were 1.6–3.8 mg/kg and 3.0–4.5 mg/kg at 60 days Pre-harvest Interval (PHI. Residues of deltamethrin from an application rate of 0.5–0.75 a.i. mg/kg were 0.13–0.14 mg/kg at 60 days PHI. Both pesticides residues were below the Maximum Residue Limits (MRLs established by the Codex Alimentarius Commission (CAC. Therefore, at the recommended dosages they are safe for use on stored rice.

  4. Rheological and fractal characteristics of unconditioned and conditioned water treatment residuals.

    Science.gov (United States)

    Dong, Y J; Wang, Y L; Feng, J

    2011-07-01

    The rheological and fractal characteristics of raw (unconditioned) and conditioned water treatment residuals (WTRs) were investigated in this study. Variations in morphology, size, and image fractal dimensions of the flocs/aggregates in these WTR systems with increasing polymer doses were analyzed. The results showed that when the raw WTRs were conditioned with the polymer CZ8688, the optimum polymer dosage was observed at 24 kg/ton dry sludge. The average diameter of irregularly shaped flocs/aggregates in the WTR suspensions increased from 42.54 μm to several hundred micrometers with increasing polymer doses. Furthermore, the aggregates in the conditioned WTR system displayed boundary/surface and mass fractals. At the optimum polymer dosage, the aggregates formed had a volumetric average diameter of about 820.7 μm, with a one-dimensional fractal dimension of 1.01 and a mass fractal dimension of 2.74 on the basis of the image analysis. Rheological tests indicated that the conditioned WTRs at the optimum polymer dosage showed higher levels of shear-thinning behavior than the raw WTRs. Variations in the limiting viscosity (η(∞)) of conditioned WTRs with sludge content could be described by a linear equation, which were different from the often-observed empirical exponential relationship for most municipal sludge. With increasing temperature, the η(∞) of the raw WTRs decreased more rapidly than that of the raw WTRs. Good fitting results for the relationships between lgη(∞)∼T using the Arrhenius equation indicate that the WTRs had a much higher activation energy for viscosity of about 17.86-26.91 J/mol compared with that of anaerobic granular sludge (2.51 J/mol) (Mu and Yu, 2006). In addition, the Bingham plastic model adequately described the rheological behavior of the conditioned WTRs, whereas the rheology of the raw WTRs fit the Herschel-Bulkley model well at only certain sludge contents. Considering the good power-law relationships between the

  5. Biofuels Combustion

    Science.gov (United States)

    Westbrook, Charles K.

    2013-04-01

    This review describes major features of current research in renewable fuels derived from plants and from fatty acids. Recent and ongoing fundamental studies of biofuel molecular structure, oxidation reactions, and biofuel chemical properties are reviewed, in addition to combustion applications of biofuels in the major types of engines in which biofuels are used. Biofuels and their combustion are compared with combustion features of conventional petroleum-based fuels. Two main classes of biofuels are described, those consisting of small, primarily alcohol, fuels (particularly ethanol, n-butanol, and iso-pentanol) that are used primarily to replace or supplement gasoline and those derived from fatty acids and used primarily to replace or supplement conventional diesel fuels. Research efforts on so-called second- and third-generation biofuels are discussed briefly.

  6. Biofuels combustion.

    Science.gov (United States)

    Westbrook, Charles K

    2013-01-01

    This review describes major features of current research in renewable fuels derived from plants and from fatty acids. Recent and ongoing fundamental studies of biofuel molecular structure, oxidation reactions, and biofuel chemical properties are reviewed, in addition to combustion applications of biofuels in the major types of engines in which biofuels are used. Biofuels and their combustion are compared with combustion features of conventional petroleum-based fuels. Two main classes of biofuels are described, those consisting of small, primarily alcohol, fuels (particularly ethanol, n-butanol, and iso-pentanol) that are used primarily to replace or supplement gasoline and those derived from fatty acids and used primarily to replace or supplement conventional diesel fuels. Research efforts on so-called second- and third-generation biofuels are discussed briefly.

  7. Treatment of air pollution control residues with iron rich waste sulfuric acid: does it work for antimony (Sb)?

    Science.gov (United States)

    Okkenhaug, Gudny; Breedveld, Gijs D; Kirkeng, Terje; Lægreid, Marit; Mæhlum, Trond; Mulder, Jan

    2013-03-15

    Antimony (Sb) in air pollution control (APC) residues from municipal solid waste incineration has gained increased focus due to strict Sb leaching limits set by the EU landfill directive. Here we study the chemical speciation and solubility of Sb at the APC treatment facility NOAH Langøya (Norway), where iron (Fe)-rich sulfuric acid (∼3.6M, 2.3% Fe(II)), a waste product from the industrial extraction of ilmenite, is used for neutralization. Antimony in water extracts of untreated APC residues occurred exclusively as pentavalent antimonate, even at low pH and Eh values. The Sb solubility increased substantially at pH<10, possibly due to the dissolution of ettringite (at alkaline pH) or calcium (Ca)-antimonate. Treated APC residues, stored anoxically in the laboratory, simulating the conditions at the NOAH Langøya landfill, gave rise to decreasing concentrations of Sb in porewater, occurring exclusively as Sb(V). Concentrations of Sb decreased from 87-918μgL(-1) (day 3) to 18-69μgL(-1) (day 600). We hypothesize that an initial sorption of Sb to Fe(II)-Fe(III) hydroxides (green rust) and eventually precipitation of Ca- and Fe-antimonates (tripuhyite; FeSbO4) occurred. We conclude that Fe-rich, sulfuric acid waste is efficient to immobilize Sb in APC residues from waste incineration. Copyright © 2013 Elsevier B.V. All rights reserved.

  8. Assessment of the nature of residual masses at end of treatment in lymphoma patients using volume perfusion computed tomography

    Energy Technology Data Exchange (ETDEWEB)

    Syha, R.; Gruenwald, L.; Spira, D.; Ketelsen, D.; Claussen, C.D.; Horger, M. [Eberhard Karls University, Department of Diagnostic Radiology, Tuebingen (Germany); Horger, T. [Technische Universitaet Muenchen, M2 - Lehrstuhl fuer Numerische, Garching (Germany); Vogel, W. [Eberhard Karls University, Department of Medical Oncology and Haematology, Tuebingen (Germany)

    2014-03-15

    To determine the diagnostic benefit of volume perfusion computed tomography (VPCT) at end of treatment for response assessment in lymphoma patients. Seventy-five patients with different lymphoma subtypes were included: 50/75 patients had residual masses at end of treatment, 26/50 patients underwent VPCT at baseline and at end of treatment, and 24/50 patients only had end-of-treatment VPCTs. We evaluated the size of the main lymphoma mass, its blood flow (BF), blood volume (BV) and k-trans, calculated ratios (baseline and end of treatment) as well as sensitivity/specificity/negative (NPV)/positive predictive values (PPV). For VPCT at end of treatment, a cutoff threshold between responders and non-responders was calculated. For patients undergoing VPCT at baseline and end of treatment, reduction in size, BF, BV and k-trans was significant (P < 0.001). Identification of non-response was reached at: <53 % reduction in size (sensitivity/specificity/accuracy/PPV/NPV of 88.89 %/62.5 %/80.77 %/84.21 %/71.43 %), <15 % reduction of BF (sensitivity/specificity/accuracy/PPV/NPV of 100 %/37.5 %/80.77 %/0.26 %/100 %), or <45 % reduction of k-trans (sensitivity/specificity/accuracy/PPV/NPV of 88.89 %/75 %/84.62 %/88.89 %/75 %). In the subgroup undergoing VPCT at end of treatment, BF >18.51 ml/100 ml indicated non-responsiveness (sensitivity 92.86 %, specificity 72.73 %, accuracy 84 %, PPV 81.25 %, NPV 88.89 %). VPCT seems adequate for assessment of lymphoma response at end of treatment. The degree of residual lymphoma perfusion at end of treatment helps to identify patients likely to remain in remission 1 year after completion of therapy. (orig.)

  9. Effects of thermal treatment on mineralogy and heavy metal behavior in iron oxide stabilized air pollution control residues

    DEFF Research Database (Denmark)

    Sørensen, Mette Abildgaard; Bender-Koch, C.; Starckpoole, M. M.

    2000-01-01

    Stabilization of air pollution control residues by coprecipitation with ferrous iron and subsequent thermal treatment (at 600 and 900 °C) has been examined as a means to reduce heavy metal leaching and to improve product stability. Changes in mineralogy and metal binding were analyzed using various...... volatilized or destabilized with respect to leaching. Pb, in particular, exhibited increased reactivity following the formation of an ordered iron oxide structure at 900 °C. The thermal treatment had a positive effect on Cr release, which was reduced significantly at 900 °C in the presence of organic matter...

  10. Field determination of biomass burning emission ratios and factors via open-path FTIR spectroscopy and fire radiative power assessment: headfire, backfire and residual smouldering combustion in African savannahs

    Directory of Open Access Journals (Sweden)

    M. J. Wooster

    2011-11-01

    Full Text Available Biomass burning emissions factors are vital to quantifying trace gas release from vegetation fires. Here we evaluate emissions factors for a series of savannah fires in Kruger National Park (KNP, South Africa using ground-based open path Fourier transform infrared (FTIR spectroscopy and an IR source separated by 150–250 m distance. Molecular abundances along the extended open path are retrieved using a spectral forward model coupled to a non-linear least squares fitting approach. We demonstrate derivation of trace gas column amounts for horizontal paths transecting the width of the advected plume, and find for example that CO mixing ratio changes of ~0.01 μmol mol−1 [10 ppbv] can be detected across the relatively long optical paths used here. Though FTIR spectroscopy can detect dozens of different chemical species present in vegetation fire smoke, we focus our analysis on five key combustion products released preferentially during the pyrolysis (CH2O, flaming (CO2 and smoldering (CO, CH4, NH3 processes. We demonstrate that well constrained emissions ratios for these gases to both CO2 and CO can be derived for the backfire, headfire and residual smouldering combustion (RSC stages of these savannah fires, from which stage-specific emission factors can then be calculated. Headfires and backfires often show similar emission ratios and emission factors, but those of the RSC stage can differ substantially. The timing of each fire stage was identified via airborne optical and thermal IR imagery and ground-observer reports, with the airborne IR imagery also used to derive estimates of fire radiative energy (FRE, allowing the relative amount of fuel burned in each stage to be calculated and "fire averaged" emission ratios and emission factors to be determined. These "fire averaged" metrics are dominated by the headfire contribution, since the FRE data indicate that the vast majority

  11. Turbulent combustion

    Energy Technology Data Exchange (ETDEWEB)

    Talbot, L.; Cheng, R.K. [Lawrence Berkeley Laboratory, CA (United States)

    1993-12-01

    Turbulent combustion is the dominant process in heat and power generating systems. Its most significant aspect is to enhance the burning rate and volumetric power density. Turbulent mixing, however, also influences the chemical rates and has a direct effect on the formation of pollutants, flame ignition and extinction. Therefore, research and development of modern combustion systems for power generation, waste incineration and material synthesis must rely on a fundamental understanding of the physical effect of turbulence on combustion to develop theoretical models that can be used as design tools. The overall objective of this program is to investigate, primarily experimentally, the interaction and coupling between turbulence and combustion. These processes are complex and are characterized by scalar and velocity fluctuations with time and length scales spanning several orders of magnitude. They are also influenced by the so-called {open_quotes}field{close_quotes} effects associated with the characteristics of the flow and burner geometries. The authors` approach is to gain a fundamental understanding by investigating idealized laboratory flames. Laboratory flames are amenable to detailed interrogation by laser diagnostics and their flow geometries are chosen to simplify numerical modeling and simulations and to facilitate comparison between experiments and theory.

  12. Chemical composition and properties of ashes from combustion plants using Miscanthus as fuel.

    Science.gov (United States)

    Lanzerstorfer, Christof

    2017-04-01

    Miscanthus giganteus is one of the energy crops considered to show potential for a substantial contribution to sustainable energy production. In the literature there is little data available about the chemical composition of ashes from the combustion of Miscanthus and practically no data about their physical properties. However, for handling, treatment and utilization of the ashes this information is important. In this study ashes from two biomass combustion plants using Miscanthus as fuel were investigated. The density of the ashes was 2230±35kg/m 3 , which was similar to the density of ashes from straw combustion. Also the bulk densities were close to those reported for straw ashes. The flowability of the ashes was a little worse than the flowability of ashes from wood combustion. The measured heavy metal concentrations were below the usual limits for utilization of the ashes as soil conditioner. The concentrations in the bottom ash were similar to those reported for ash from forest residue combustion plants. In comparison with cyclone fly ashes from forest residue combustion the measured heavy metal concentrations in the cyclone fly ash were considerably lower. Cl - , S and Zn were enriched in the cyclone fly ash which is also known for ashes from wood combustion. In comparison with literature data obtained from Miscanthus plant material the concentrations of K, Cl - and S were lower. This can be attributed to the fact that the finest fly ash is not collected by the cyclone de-dusting system of the Miscanthus combustion plants. Copyright © 2016. Published by Elsevier B.V.

  13. Statistical modeling to management and treatment of scrap with low and very low residual activity

    International Nuclear Information System (INIS)

    Garcia-Bermejo Fernandez, R.; Anaya Lazaro, M.

    2011-01-01

    The experience of recent years on the management of scrap metal containing residual activity have allowed the development of a simple statistical model for the management of these materials. This statistical model includes a breakdown of the various processing operations to which these materials undergo and the effects in the process of radiological controls associated to the control of declassification that defines disposal (recycled by smelting, reclamation, temporary storage the plant or sent to final storage of radioactive waste.

  14. Phytotoxicity and groundwater impacts of leaching from thermal treatment residues in roadways.

    Science.gov (United States)

    Phoungthong, Khamphe; Shao, Li-Ming; He, Pin-Jing; Zhang, Hua

    2018-01-01

    The use of coal fly ash (CFA), municipal solid waste incinerator bottom ash (MSWIBA) and flue gas desulfurization residue (FGDR) in road construction has become very common owing to its economical advantages. However, these residues may contain toxic constituents that pose an environmental risk if they leach out and flow through the soil, surface water and groundwater. Therefore, it is necessary to assess the ecotoxicity and groundwater impact of these residues before decisions can be made regarding their utilization for road construction. In this study, the physico-chemical characteristics, leaching and phytotoxicity of these residues were investigated. Specifically, multivariate analyses were used to evaluate the contributions of the leaching constituents of the CFA, MSWIBA and FGDR leachates to the germination index of wheat seeds. B, Ba, Cr, Cu, Fe and Pb were found to be more toxic to the wheat seeds than the other heavy metals. Furthermore, the leached concentrations of the constituents from the CFA, MSWIBA and FGDR were below the regulatory threshold limits of the Chinese identification standard for hazardous wastes. Analyses conducted using a numerical groundwater model (WiscLEACH) indicated that the predicted field concentrations of metals from the CFA, MSWIBA and FGDR increased with time up to about 30years at the point of compliance, then decreased with time and distance. Overall, this study demonstrated that the risks resulting from MSWIBA, CFA and FGDR leaching could be assessed before its utilization for road construction, providing crucial information for the adoption of these alternative materials. Copyright © 2016. Published by Elsevier B.V.

  15. Treatment and use of air pollution control residues from MSW incineration: An overview

    OpenAIRE

    Quina, Margarida J.; Bordado, João C.; Quinta-Ferreira, Rosa M.

    2008-01-01

    This work reviews strategies for the management of municipal solid waste incineration (MSWI) residues, particularly solid particles collected from flue gases. These tiny particles may be retained by different equipment, with or without additives (lime, activated carbon, etc.), and depending on the different possible combinations, their properties may vary. In industrial plants, the most commonly used equipment for heat recovery and the cleaning of gas emissions are: heat recovery devices (boi...

  16. The effect of different treatment technologies on the fate of antibiotic resistance genes and class 1 integrons after the application of residual municipal wastewater solids to soil

    Science.gov (United States)

    Land-application of residual wastewater solids is an important environmental source of antibiotic resistance genes (ARGs). Treatment technologies exist that can reduce ARG levels in residual solids prior to land-application, but the effect of these technologies on ARG levels in soil following land-a...

  17. Pilot Testing of WRI'S Novel Mercury Control Technology by Pre-Combustion Thermal Treatment of Coal

    Energy Technology Data Exchange (ETDEWEB)

    Alan Bland; Jesse Newcomer; Kumar Sellakumar

    2008-08-17

    The challenges to the coal-fired power industry continue to focus on the emission control technologies, such as mercury, and plant efficiency improvements. An alternate approach to post-combustion control of mercury, while improving plant efficiency deals with Western Research Institute's (WRI)'s patented pre-combustion mercury removal and coal upgrading technology. WRI was awarded under the DOE's Phase III Mercury program, to evaluate the effectiveness of WRI's novel thermal pretreatment process to achieve >50% mercury removal, and at costs of <$30,000/lb of Hg removed. WRI has teamed with Etaa Energy, Energy and Environmental Research Center (EERC), Foster Wheeler North America Corp. (FWNA), and Washington Division of URS (WD-URS), and with project co-sponsors including Electric Power Research Institute (EPRI), Southern Company, Basin Electric Power Cooperative (BEPC), Montana-Dakota Utilities (MDU), North Dakota Industrial Commission (NDIC), Detroit Edison (DTE), and SaskPower to undertake this evaluation. The technical objectives of the project were structured in two phases: Phase I--coal selection and characterization, and bench-and PDU-scale WRI process testing and; and Phase II--pilot-scale pc combustion testing, design of an integrated boiler commercial configuration, its impacts on the boiler performance and the economics of the technology related to market applications. This report covers the results of the Phase I testing. The conclusion of the Phase I testing was that the WRI process is a technically viable technology for (1) removing essentially all of the moisture from low rank coals, thereby raising the heating value of the coal by about 30% for subbituminous coals and up to 40% for lignite coals, and (2) for removing volatile trace mercury species (up to 89%) from the coal prior to combustion. The results established that the process meets the goals of DOE of removing <50% of the mercury from the coals by pre-combustion methods

  18. Radioactive waste treatment apparatus

    International Nuclear Information System (INIS)

    Abrams, R.F.; Chellis, J.G.

    1983-01-01

    Radioactive waste treatment apparatus is disclosed in which the waste is burned in a controlled combustion process, the ash residue from the combustion process is removed and buried, the gaseous effluent is treated in a scrubbing solution the pH of which is maintained constant by adding an alkaline compound to the solution while concurrently extracting a portion of the scrubbing solution, called the blowdown stream. The blowdown stream is fed to the incinerator where it is evaporated and the combustibles in the blowdown stream burned and the gaseous residue sent to the scrubbing solution. Gases left after the scrubbing process are treated to remove iodides and are filtered and passed into the atmosphere

  19. Aging of aluminum/iron-based drinking water treatment residuals in lake water and their association with phosphorus immobilization capability.

    Science.gov (United States)

    Wang, Changhui; Yuan, Nannan; Pei, Yuansheng; Jiang, He-Long

    2015-08-15

    Aluminum and Fe-based drinking water treatment residuals (DWTRs) have shown a high potential for use by geoengineers in internal P loading control in lakes. In this study, aging of Al/Fe-based DWTRs in lake water under different pH and redox conditions associated with their P immobilization capability was investigated based on a 180-day incubation test. The results showed that the DWTRs before and after incubation under different conditions have similar structures, but their specific surface area and pore volume, especially mesopores with radius at 2.1-5.0 nm drastically decreased. The oxalate extractable Al contents changed little although a small amount of Al transformed from oxidizable to residual forms. The oxalate extractable Fe contents also decreased by a small amount, but the transformation from oxidizable to residual forms were remarkable, approximately by 14.6%. However, the DWTRs before and after incubation had similar P immobilization capabilities in solutions and lake sediments. Even the maximum P adsorption capacity estimated by the Langmuir model increased after incubation. Therefore, it was not necessary to give special attention to the impact of Al and Fe aging on the effectiveness of DWTRs for geoengineering in lakes. Copyright © 2015 Elsevier Ltd. All rights reserved.

  20. Tubular combustion

    CERN Document Server

    Ishizuka, Satoru

    2014-01-01

    Tubular combustors are cylindrical tubes where flame ignition and propagation occur in a spatially confined, highly controlled environment, in a nearly flat, elongated geometry. This allows for some unique advantages where extremely even heat dispersion is required over a large surface while still maintaining fuel efficiency. Tubular combustors also allow for easy flexibility in type of fuel source, allowing for quick changeover to meet various needs and changing fuel pricing. This new addition to the MP sustainable energy series will provide the most up-to-date research on tubular combustion--some of it only now coming out of private proprietary protection. Plentiful examples of current applications along with a good explanation of background theory will offer readers an invaluable guide on this promising energy technology. Highlights include: * An introduction to the theory of tubular flames * The "how to" of maintaining stability of tubular flames through continuous combustion * Examples of both small-scal...

  1. Switching to aripiprazole for the treatment of residual mutism resulted in distinct clinical courses in two catatonic schizophrenia cases.

    Science.gov (United States)

    Muneoka, Katsumasa; Kanahara, Nobuhisa; Kimura, Shou

    2017-01-01

    The efficacy of a partial agonist for the dopamine D 2 receptor, aripiprazole, for catatonia in schizophrenia has been reported. We report distinct clinical courses in challenging aripiprazole to treat residual mutism after severe catatonic symptoms improved. In the first case, mutism was successfully treated when the patient was switched from olanzapine to aripiprazole. In contract, switching to aripiprazole from risperidone aggravated auditory hallucinations in the second case. We will discuss the benefits and risks of using aripiprazole for the treatment of catatonic schizophrenia and the possibility of dopamine supersensitivity psychosis.

  2. Switching to aripiprazole for the treatment of residual mutism resulted in distinct clinical courses in two catatonic schizophrenia cases

    Directory of Open Access Journals (Sweden)

    Katsumasa Muneoka

    2017-02-01

    Full Text Available Objectives: The efficacy of a partial agonist for the dopamine D2 receptor, aripiprazole, for catatonia in schizophrenia has been reported. Methods: We report distinct clinical courses in challenging aripiprazole to treat residual mutism after severe catatonic symptoms improved. Results: In the first case, mutism was successfully treated when the patient was switched from olanzapine to aripiprazole. In contract, switching to aripiprazole from risperidone aggravated auditory hallucinations in the second case. Conclusions: We will discuss the benefits and risks of using aripiprazole for the treatment of catatonic schizophrenia and the possibility of dopamine supersensitivity psychosis.

  3. Influence of post-harvest application rates of cyprodinil, treatment time and temperature on residue levels and efficacy in controlling green mould on 'Valencia' oranges.

    Science.gov (United States)

    Schirra, Mario; D'Aquino, Salvatore; Cabras, Paolo; Angioni, Alberto

    2009-07-01

    The effectiveness of heat treatments with water and cyprodinil in controlling post-harvest green mould caused by Penicillium digitatum was investigated on artificially inoculated 'Valencia' oranges. Residue levels of cyprodinil were determined in the oranges as a function of active ingredient concentration, temperature and treatment time. Cyprodinil residues were significantly dependent on treatment time when applied at 600 mg l(-1) and 20 degrees C, but not when fruit were treated at 150-300 mg l(-1). The application of cyprodinil at 50 or 100 mg l(-1) at 55 degrees C for 30 s produced similar residue levels, while residues increased when the application rate was 150 mg l(-1). Cyprodinil at 100 mg l(-1) and 60 degrees C produced a significant increase in residues compared to treatment at 50 mg l(-1); no significant increase in residues was found when the application rate was raised from 100 to 150 mg l(-1). In comparison to treatments performed at 20 degrees C, the application of a heated cyprodinil mixture resulted in significantly higher residues in fruit. All treatments with cyprodinil at 20 degrees C similarly reduced green mould after 7 days of storage at 20 degrees C. After 18 days, treatment with cyprodinil at 600 mg l(-1) for 30 s was more effective than at 150-300 mg l(-1). When dip time was extended to 90 or 180 s, treatment efficacy was positively related to fungicide concentration. Treatments with water at 55 degrees C for 30 s were as effective as cyprodinil at 50-100 mg l(-1), but less effective than cyprodinil at 150 mg l(-1). After 7 days, treatment with water or cyprodinil at 50-150 mg l(-1) and 60 degrees C were equally effective in controlling green mould; while, after 18 days, treatment with cyprodinil at 150 mg l(-1) was consistently more effective than at 50-100 mg l(-1) or hot water alone.

  4. Advanced Combustion

    Energy Technology Data Exchange (ETDEWEB)

    Holcomb, Gordon R. [NETL

    2013-03-11

    The activity reported in this presentation is to provide the mechanical and physical property information needed to allow rational design, development and/or choice of alloys, manufacturing approaches, and environmental exposure and component life models to enable oxy-fuel combustion boilers to operate at Ultra-Supercritical (up to 650{degrees}C & between 22-30 MPa) and/or Advanced Ultra-Supercritical conditions (760{degrees}C & 35 MPa).

  5. Methylene blue treatment for residual symptoms of bipolar disorder: randomised crossover study.

    Science.gov (United States)

    Alda, Martin; McKinnon, Margaret; Blagdon, Ryan; Garnham, Julie; MacLellan, Susan; O'Donovan, Claire; Hajek, Tomas; Nair, Cynthia; Dursun, Serdar; MacQueen, Glenda

    2017-01-01

    Residual symptoms and cognitive impairment are among important sources of disability in patients with bipolar disorder. Methylene blue could improve such symptoms because of its potential neuroprotective effects. We conducted a double-blind crossover study of a low dose (15 mg, 'placebo') and an active dose (195 mg) of methylene blue in patients with bipolar disorder treated with lamotrigine. Thirty-seven participants were enrolled in a 6-month trial (trial registration: NCT00214877). The outcome measures included severity of depression, mania and anxiety, and cognitive functioning. The active dose of methylene blue significantly improved symptoms of depression both on the Montgomery-Åsberg Depression Rating Scale and Hamilton Rating Scale for Depression (P = 0.02 and 0.05 in last-observation-carried-forward analysis). It also reduced the symptoms of anxiety measured by the Hamilton Rating Scale for Anxiety (P = 0.02). The symptoms of mania remained low and stable throughout the study. The effects of methylene blue on cognitive symptoms were not significant. The medication was well tolerated with transient and mild side-effects. Methylene blue used as an adjunctive medication improved residual symptoms of depression and anxiety in patients with bipolar disorder. © The Royal College of Psychiatrists 2017.

  6. Effect of thermal treatments on the degradation of antibiotic residues in food.

    Science.gov (United States)

    Tian, Lei; Khalil, Salma; Bayen, Stéphane

    2017-11-22

    The thermal stability of antibiotics commonly detected in food is reviewed. To quantify degradation, 2 major techniques have been reported: liquid chromatography-based methods and microbiological tests. As the degradation products may also display some antimicrobial activity, microbiological tests may not be considered accurate analytical methods for quantifying antibiotic residues' degradation. Degradation percentages are summarized for different antibiotics and for various media (water, oil, milk, and animal tissues). Studies presented in the literature confirm that the thermal degradation of β-lactams, quinolones, sulfonamides, and tetracyclines can be described using a first-order kinetic model. Degradation rates, k, derived for this model for liquid matrix (water) at 100 °C, followed the general trend amongst antibiotic classes: β-lactams = tetracyclines (most heat-labile) > lincomycin > amphenicols > sulfonamides > oxfendazole > levamisole (most heat-stable). Although thermal processing results in a decrease in the concentration of parent antibiotic residues, degradation by-products have not been properly characterized to date. As some of these products were shown to be hazardous, further investigation is needed to determine their impact on food safety and human health. It is therefore currently difficult to definitively conclude whether or not antibiotic degradation during food processing is necessarily beneficial in terms of food safety.

  7. Immobilization of Co{sup 2+} and Cs{sup +} in zeolites by thermal treatment and by combustion; Inmovilizacion de Co{sup 2+} y Cs{sup +} en zeolitas por tratamiento termico y por combustion

    Energy Technology Data Exchange (ETDEWEB)

    Rodriguez T, R.; Bulbulian G, S. [ININ, 52045 Ocoyoacac, Estado de Mexico (Mexico)]. e-mail: rosarodtre@yahoo.com

    2005-07-01

    The radioactive waste, either those that take place in the {sup 235}U fission or those that are used in the radiochemical laboratories, are dangerous for the human being and for the one environment. The liquid radioactive wastes are of those that present bigger problem. It has intended to retain by the ion exchange method the radioactive ions of the liquids using, for example, zeolites. In this work so much synthetic zeolites was used (A and X) like a natural zeolite (clinoptilolite). Its were put in contact with cobalt or cesium solutions to simulate radioactive solutions. A part of the zeolite cations were exchanged with cobalt or cesium cations, eliminating them by this way of the solution. However, in extreme conditions these cations can be leached of the solids. To immobilize the cobalt or cesium cations in the zeolites net its are usually carried out thermal treatments to such temperatures that the structure is destroyed and that the contaminating ions are trapped in a solid often vitreous. The exchanged zeolites with cobalt or cesium, on one hand, its were thermally treated to different temperatures during three hours and by the other one, according to the treatment method by combustion, to different temperatures during five minutes in presence of urea, later its were put in contact with a solution of NaCl to measure the leaching of the interest cations. These solutions were analyzed by neutron activation. In general it was found that as the treatment temperature increases (in both methods) the so much immobility of the cesium like of the cobalt it increases. The grade of crystallinity of the samples before and after the treatments it was determined by X-ray diffraction. (Author)

  8. INVESTIGATION OF THE EFFECT OF HEAT TREATMENT ON RESIDUAL DEFORMATION CHIPPER KNIVES

    Directory of Open Access Journals (Sweden)

    A. V. Alifanov

    2015-01-01

    Full Text Available To carry out experimental studies of the influence of temperature modes on residual deformation of the sample-ing knives were manufactured pilot models of chipper knives 6HV2S steels (basic and U8A 9HF each in size up to its analog (finished knife. We draw on the modes recommended for these steels.The experimentalresultsshowed that the samples with smallsize and relatively large thickness after THEN do not have any permanent deformations. Samples ments concerning thin and having a rectangularshape (length 300 mm, then there are residual after deformation as Trough. The magnitude of the deflection is greater the smaller the ratio of the thickness of the sample to its length and width. It is found that the samples made from steel 6HV2S have a deflection value smaller than the samples of steel grades and 9HF U8A.Repair any defects in the form of troughs manage curved by heating the samples to the tempering temperature and the subsequent exposure between steel plates in a hydraulic press under a load to cool the workpiece.Thus, as a result of the research found that the residual deformation-tion (trough samples of knives from different grades (6HV2S, 9HF, U8A has a different value, depending on the geometrical parameters of knives (length, thickness, width and grades. The deflection can be easily eliminated by additional straightening.In the course of the work of steel 6HV2S supplied to the Belarusian market of Russia, at the branch of JSC «Atlant» -BSZ it was manufactured a few sets of prototypes chipper knives, intended for testing in a production environment on the woodworking enterprises of the republic (of «Ivatsevichidrev», JSC «Vitebskdrev/».Production tests of experimental knives made in accordance with the process technology-mi, developed in Barga, showed their compliance with production requirements and also require-ments of state standards, which allows recommend them for a wide introduction to woodworking factories, specializing in

  9. Advanced solutions in combustion-based WtE technologies.

    Science.gov (United States)

    Martin, Johannes J E; Koralewska, Ralf; Wohlleben, Andreas

    2015-03-01

    Thermal treatment of waste by means of combustion in grate-based systems has gained world-wide acceptance as the preferred method for sustainable management and safe disposal of residual waste. In order to maintain this position and to address new challenges and/or priorities, these systems need to be further developed with a view to energy conservation, resource and climate protection and a reduction in the environmental impact in general. MARTIN GmbH has investigated continuously how the implementation of innovative concepts in essential parts of its grate-based Waste-to-Energy (WtE) combustion technology can be used to meet the above-mentioned requirements. As a result of these efforts, new "advanced solutions" were developed, four examples of which are shown in this article. Copyright © 2014 Elsevier Ltd. All rights reserved.

  10. [Biooxidation of gold-bearing sulfide ore and subsequent biological treatment of cyanidation residues].

    Science.gov (United States)

    Kanaev, A T; Bulaev, A G; Semenchenko, G V; Kanaeva, Z K; Shilmanova, A A

    2016-01-01

    The percolation biooxidation parameters of ore from the Bakyrchik deposit were studied. An investigation of the technological parameters (such as the concentration of leaching agents, irrigation intensity, and pauses at various stages of the leaching) revealed the optimal mode for precious metal extraction. The stages of the ore processing were biooxidation, gold extraction by cyanidation or thiosulfate leaching, and biological destruction of cyanide. The gold and silver recovery rates by cyanidation were 64.0 and 57.3%, respectively. The gold and silver recovery rates by thiosulfate leaching were 64.0 and 57.3%, respectively. Gold and silver recovery rates from unoxidized ore (control experiment) by cyanidation were 20.9 and 26.8%, respectively. Thiosulfate leaching of unoxidized ore allowed the extraction of 38.8 and 24.2% of the gold and silver, respectively. Cyanidation residues were treated with bacteria of the genus Alcaligenes in order to destruct cyanide.

  11. Masonry concrete block strength compound with sawdust according to residue treatment - doi: 10.4025/actascitechnol.v34i3.14372

    Directory of Open Access Journals (Sweden)

    Paulo Sérgio Lima Souza

    2012-05-01

    Full Text Available The behavior of building blocks with the partial replacement of fine aggregates by sawdust is evaluated. The parameter adopted comprised analysis of the compressive strength according to the treatment applied to sawdust residue of the species Dinizia Excelsa Ducke (red angelim. Blocks were composed by replacing fine aggregates by sawdust at 5% weight. Before mixing the wood residues to the concrete, the former underwent treatment so that wood residues could be compatible with the cement matrix. Two treatment processes were investigated. The first treatment comprised the washing of residues in an alkaline solution (lime at a 5% proportion (weight / weight. The second treatment comprised the immersion of the residue in aluminum sulfate. Analysis was undertaken from compressive strength assays of the blocks on the 7th and 28th day. Results showed low efficiency in the alkaline-based treatment (lime and good performance in the aluminum sulfate-based treatment. The production of masonry blocks with a replacement of 5% fine aggregates for this type of treatment and species studied is possible. 

  12. Production of date palm fruits free of acaricides residues by ozone technology as post-harvest treatment.

    Science.gov (United States)

    Osman, Khaled A

    2015-06-01

    Distilled water and ozonated water as postharvest wash treatments for 15-60 min as dipping times were tested to remove two acaricides namely, dicofol and amitraz from different varieties of date fruits. Recovered amount of the acaricides was extracted using solid phase extraction (SPE) and then analyzed by gas chromatography-mass spectrometry (GC-MS). Dicofol removal percentages in the presence of ozone increased in the order of Nabtet Aly > Nabout Seif > Khalas > Sakay, while amitraz removal increased in the order of Nabtet Aly > Nabout Seif > Sakay > Khalas, respectively, and the percentages of residues on date fruits depended on the dipping time. Kinetic studies revealed that dicofol and amitraz were easily removable from date fruits treated with ozonated water. Ozone-treated date palm fruits were not associated with significant changes in antioxidant capacity, and phenolic and sugar contents. Due to the large amount of dates consumed by Saudi residents, a higher risk of exposure to pesticides, especially in children and other vulnerable individuals may occur and the search for safety methods to remove pesticides with negligible residual deposits has always been preferred. Therefore, the present study validated that ozone technology as wash treatments is safe and promising processes for the removal of acaricides from date fruits surface under domestic conditions to reduce the impact over consumer's health.

  13. Agro-Residues: Surface Treatment and Characterization of Date Palm Tree Fiber as Composite Reinforcement

    Directory of Open Access Journals (Sweden)

    Elsayed A. Elbadry

    2014-01-01

    Full Text Available The aims of this research are to investigate the effect of different surface treatment methods on the different properties of date palm fiber (DPF compared to raw DPF fibers such as surface morphology, density, thermal stability, and tensile properties. The first surface treatment is called surface hand cleaning which can be carried out by cleaning the fibers by soft sand cloth; the second one is the same as the first one after DPF heat treatment in the furnace at 100°C for 1.5 h and the third one is by chemical treatment with 1% NaOH at 100°C for 1 h. The results showed that the mechanical performance of DPF was enhanced by the different treatments and the chemical treatment has pronounced effect on the behavior of DPF. Raw fibers showed the highest variability and presented the lowest value of Weibull modulus, whereas the fibers showed less variability by carrying out the different treatments. Moreover, using soda treatment cleans the fiber surface which causes fibrillation and therefore the tensile strength of the fibers increases.

  14. Initial Effects of Reproduction Cutting Treatments on Residual Hard Mast Production in the Ouachita Mountains

    Science.gov (United States)

    Roger W. Perry; Ronald E. Thill

    2003-01-01

    We compared indices of total hard mast production (oak and hickory combined) in 20, second-growth, pine-hardwood stands under five treatments to determine the effects of different reproduction treatments on mast production in the Ouachita Mountains. We evaluated mast production in mature unharvested controls and stands under four reproduction cutting methods (single-...

  15. Ignition and combustion of sodium, fire consequences, extinguishment and prevention

    International Nuclear Information System (INIS)

    Malet, J.C.

    1996-01-01

    This document presents the results of work carried out at the IPSN on: sodium inflammation, sodium combustion (pool fires and sprayed jet fires), extinguishment (passive means and extinguishing powder), the physico-chemical behaviour of aerosols and their filtration, the protection means of concretes, intervention during and after a fire, treatment of residues, intervention equipment. The calculation codes developed during these studies are described. The experimental basis which allowed the qualification of these codes and the technological means aimed at prevention and sodium fire fighting, was obtained using programmes carried out in the experimental facilities existing in Cadarache or in collaboration with the German teams of Karlsruhe

  16. Identification of residual non-biodegradable organic compounds in wastewater effluent after two-stage biochemical treatment

    Directory of Open Access Journals (Sweden)

    Xuqing Liu

    2016-01-01

    Full Text Available The main non-biodegradable compounds (soluble microbial product – SMP of wastewater from the Maotai aromatic factories, located in the Chishui river region, were analyzed by UV spectroscopy, and by solid-phase extraction followed by gas chromatography coupled to mass spectrometry, after a two-stage biochemical treatment. The UV-Vis spectra revealed that the wastewater contained two double-bonds in conjugated systems (conjugated diene or α, β- unsaturated ketone, etc. and simple non-conjugated chromophores containing n electrons from carbonyl groups or the like. The residual organic non-biodegradable substances were identified using SPE-GC/MS analysis as complex polymers containing hydroxyl, carbonyl, and carboxyl functional groups with multiple connections to either benzene rings or heterocyclic rings. As these compounds are difficult to remove by conventional biochemical treatments, our findings provide a scientific basis for the design of efficient new strategies to remove SMP from wastewater.

  17. Residual deposits (residual soil)

    International Nuclear Information System (INIS)

    Khasanov, A.Kh.

    1988-01-01

    Residual soil deposits is accumulation of new formate ore minerals on the earth surface, arise as a result of chemical decomposition of rocks. As is well known, at the hyper genes zone under the influence of different factors (water, carbonic acid, organic acids, oxygen, microorganism activity) passes chemical weathering of rocks. Residual soil deposits forming depends from complex of geologic and climatic factors and also from composition and physical and chemical properties of initial rocks

  18. IEA combustion agreement : a collaborative task on alternative fuels in combustion

    International Nuclear Information System (INIS)

    Larmi, M.

    2009-01-01

    The focus of the alternative fuels in combustion task of the International Energy Agency is on high efficiency engine combustion, furnace combustion, and combustion chemistry. The objectives of the task are to develop optimum combustion for dedicated fuels by fully utilizing the physical and chemical properties of synthetic and renewable fuels; a significant reduction in carbon dioxide, NOx and particulate matter emissions; determine the minimum emission levels for dedicated fuels; and meet future emission standards of engines without or with minimum after-treatment. This presentation discussed the alternative fuels task and addressed issues such as synthetic fuel properties and benefits. The anticipated future roadmap was presented along with a list of the synthetic and renewable engine fuels to be studied, such as neat oxygenates like alcohols and ethers, biogas/methane and gas combustion, fuel blends, dual fuel combustion, high cetane number diesel fuels like synthetic Fischer-Tropsch diesel fuel and hydrogenated vegetable oil, and low CN number fuels. Implementation examples were also discussed, such as fuel spray studies in optical spray bombs; combustion research in optical engines and combustion chambers; studies on reaction kinetics of combustion and emission formation; studies on fuel properties and ignition behaviour; combustion studies on research engines; combustion optimization; implementing the optimum combustion in research engines; and emission measurements. Overall milestone examples and the overall schedule of participating countries were also presented. figs.

  19. Coupling of solar-assisted advanced oxidative and biological treatment for degradation of agro-residue-based soda bleaching effluent.

    Science.gov (United States)

    Dhir, Amit; Prakash, Nagaraja Tejo; Sud, Dhiraj

    2012-11-01

    This study evaluates the effect of integrated solar-assisted advanced oxidation process (AOP) and biological treatment on the extent of degradation of effluents from chlorination (C) and first alkaline extraction (E(1)) stages of soda pulp bleaching in agro-residue-based pulp and paper mill. Biodegradation of the effluents was attempted in suspended mode using activated sludge from the functional pulp and paper industry effluent treatment plant acclimatized to effluents in question. The photocatalytic treatment was employed using zinc oxide (ZnO) in slurry mode for decontamination of effluents in a batch manner and the degradation was evaluated in terms of reduction in chemical oxygen demand. The biological treatment (24 h) of C and E(1) effluent resulted in 30 and 57 % of degradation, respectively. Solar-induced AOP of C and E(1) effluents resulted in 53 and 43 % degradation under optimized conditions (2.5 g L(-1) ZnO at pH 8.0) after 6 h of exposure. For C effluent, a short duration of solar/ZnO (1 h) prior to biological treatment reduced the time required at biological step from 24 to 12 h for almost same extent (92 %) of degradation. However, sequential biological treatment (24 h) followed by solar/ZnO (2 h) resulted in 85.5 % degradation. In contrast, in the case of E(1) effluent, sequential biological (24 h)-solar/ZnO (2 h) system effectively degrades effluent to 95.4 % as compared to 84.8 % degradation achieved in solar/ZnO (2 h)-biological treatment (24 h) system. In the present study, the sequencing of photocatalysis with the biological treatment is observably efficient and technically viable process for the complete mineralization of the effluents.

  20. Trace Analysis of Pharmaceutical Residues in Wastewater Treatment Plants in Rio de Janeiro, Brazil

    Directory of Open Access Journals (Sweden)

    Aldo Pacheco Ferreira

    2014-05-01

    Full Text Available The occurrence and fate of trace-level contamination of pharmaceuticals in the aquatic environment has been recognized as one of the emerging issues in environmental chemistry. The effluents of wastewater treatment plants, usually directly emitted to the environment, often contain the anti-inflammatory drug diclofenac. Diclofenac was chosen because it is of high consumption; by background literature indicate toxic effects on biota and the lack of profile in sewage removal provided by the city. For this purpose, a survey on the presence of diclofenac in urban wastewater of Rio de Janeiro was carried out. It were evaluated diclofenac concentration in the affluent and effluent from wastewater treatment plant (WWTP Penha and Ilha do Governador, Rio de Janeiro, Brazil. Samples were collected along the line of treatment of each WWTP, and for clean up the samples were solid phase extraction (SPE, analysed by high performance liquid chromatography (HPLC, assisted by diode array detector (DAD techniques. The removal efficiency of pharmaceuticals in the wastewater treatment plants was roughly evaluated. Diclofenac was detected in all samples analysed wastewater (treated and raw, which confirms the low removal efficiency of conventional treatment systems, aerobes and anaerobes.

  1. Influence of the surface treatment of tire rubber residues added in mortars

    Directory of Open Access Journals (Sweden)

    A. C. Marques

    Full Text Available In this work it was evaluated the influence tire rubber addition in mortars in order to replace part of the sand (12% by volume. It was also intended to verify if the tire rubber treatment with NaOH saturated aqueous solution causes interference on the mechanical properties of the mixture. Compressive strength, splitting tensile strength, water absorption, modulus of elasticity, and flow test were made in specimens of 5cmx10cm and the tests were carried out to 7, 28, 56, 90, and 180 days. The results show reduction on mechanical properties values after addition of tire rubber and decrease of the workability. It was also observed that the tire rubber treatment does not cause any alteration on the results compared to the rubber without treatment.

  2. Study of treatment of the residual waters of an atomizer milk plant

    International Nuclear Information System (INIS)

    Sierra C, J.H.; Wills B, B.A.; Saldarriaga M, J.C.

    1999-01-01

    The results of a study on the characterization and treatment test of the wastewater of a dairy plant, which is mainly devoted to the production of powdered milk and whey, are presented in this work. It includes a description of the procedures to carry out the field and the laboratory test. Several coagulation tests were run using alum, lime, ferric sulfate, ferric chloride, sulfuric acid and a poli electrolyte. In the case of wastewater from process all treatments were very effective in removal of both suspended and fatty solids; the removal of the organic improved with the addition of ferric sulfate plus floatation, and with the use of soda and ferric chloride. The treatment of wastewater from washing operations was more effective with a serial addition of sulfuric acid and ferric chloride

  3. Application of processes of advanced oxidation as phenol treatment in industrial residual waters of refinery

    International Nuclear Information System (INIS)

    Forero, Jorge Enrique; Ortiz, Olga Patricia; Rios, Fabian

    2005-01-01

    Although more efficient and economical processes for the treatment of sewage have been developed in recent years, the challenge they are facing-due to the greater knowledge of the effect that pollutants have on the environment, the greater consumption of water because of the development of human and industrial activity and the reduction of fresh water sources indicate that we are far from attaining the final solution. This affirmation specially applies to the pollutants, which are resistant to biological treatment processes, such as most of the aromatic compounds found in sewage of the petrochemical industries. In this document, the processes known as advanced oxidation will be explored. Theses have been reported as having the greatest potential in the treatment of these pollutants. Likewise the results of the application of these technologies with waters typical of the petroleum industry will be reported. These have previously been evaluated with processes of typical ozonization

  4. Evaluation of residual iron in carbon nanotubes purified by acid treatments

    Energy Technology Data Exchange (ETDEWEB)

    Edwards, E.R., E-mail: eliltonedwards@hotmail.com [Sao Paulo State University - UNESP, Av. Dr. Ariberto Pereira da Cunha, 333, CEP: 12.516-410 CP:20, Guaratingueta, SP (Brazil); Antunes, E.F. [National Institute for Space Research - INPE, Av. dos Astronautas, 1758, CEP: 12.254-97, Sao Jose dos Campos-SP (Brazil); Aeronautical Institute of Technology - ITA, Praca Marechal Eduardo Gomes, 50, CEP: 12.228-900, Sao Jose dos Campos-SP (Brazil); Botelho, E.C. [Sao Paulo State University - UNESP, Av. Dr. Ariberto Pereira da Cunha, 333, CEP: 12.516-410 CP:20, Guaratingueta, SP (Brazil); Baldan, M.R.; Corat, E.J. [National Institute for Space Research - INPE, Av. dos Astronautas, 1758, CEP: 12.254-97, Sao Jose dos Campos-SP (Brazil)

    2011-11-01

    A detailed analysis by X-ray photoelectron spectroscopy was carried out on multi-walled carbon nanotube (MWCNT) surfaces after non-oxidative and oxidative purification treatments in liquid-phase. The MWCNT were produced by pyrolysis of camphor and ferrocene, that provides a high yield but with high iron contamination ({approx}15% wt). The elimination and/or oxidation of iron nanoparticles were monitored by Fe2p and O1s core level. Oxygen-based functional groups attachment was also investigated by C1s fitting. The effectiveness of each treatment in iron removal was evaluated by thermogravimetric analysis (TGA) and atomic absorption spectroscopy (AAS). The integrity of the MWCNT structure was verified by Raman spectroscopy (RS) and transmission electron microscopy (TEM). A purity degree higher than 98% was achieved only with non-oxidative treatments using sonification process.

  5. Coal combustion: Effect of process conditions on char reactivity. Final technical report, September 1, 1991--May 31, 1995

    Energy Technology Data Exchange (ETDEWEB)

    Zygourakis, K.

    1996-02-01

    Coal utilization involves two major stages: coal pyrolysis and char combustion. Figure 1.1 summarizes the steps of these processes. During the pyrolysis stage, heated particles from plastic coals soften, swell and release their volatiles before resolidifying again. During the combustion or gasification stage, char particles may ignite and fragment as the carbon is consumed leaving behind a solid ash residue. Process conditions such as pyrolysis heating rate, heat treatment temperature, pyrolysis atmosphere, and particle size are shown to chemically and physically affect the coal during pyrolysis and the resulting char. Consequently, these pyrolysis conditions as well as the combustion conditions such as the oxygen concentration and combustion temperature affect the char reactivity and ignition phenomena during the combustion stage. Better understanding of the fundamental mechanisms of coal pyrolysis and char combustion is needed to achieve greater and more efficient utilization of coal. Furthermore, this knowledge also contributes to the development of more accurate models that describe the transient processes involved in coal combustion. The project objectives were to investigate the effect of pyrolysis conditions on the macropore structure and subsequent reactivity of chars.

  6. Alternatives for the treatment of the organic fraction of the urban solid residuals

    International Nuclear Information System (INIS)

    Benitez Fonseca, Mabelin; Fernandez Mena, Dalia; Abalos Rodriguez, Arelis; Rodriguez Perez, Suyen

    2011-01-01

    The decomposition of municipal solid waste outdoors, or in some cases burning under the same conditions, is action now and final disposition of these wastes without measuring their consequences. In the student's residence 'Antonio Maceo' Orient University is hosting up to 2250 students belonging to a total of 22 university, generating at full capacity, 3375 kg / day of MSW. This research aims to analyze the solid waste generated in the student's residence, where improperly evaluated the final disposition thereof. It was found that discharges are not separated at the source observed at the landfill, food waste, sweeping waste, paper and cardboard, plastics, glass, metal, textile waste, wood, etc. Samplings were carried out directly in 12 rooms of the residence for a total of 48 people, along with students, as part of the educational activities implemented within this work. The average weight of degradable waste generated was 2.5 kg / day during the sampling, revealing the presence of traces of cooked food (cereals, legumes, carbohydrates), fruit and vegetable remains, remains of shells of different origins ( meats, eggs), remnants of tea, etc. The average content of total solids in the waste sampled was 36.3 ± 5.4% and volatile solids content on dry weight was 81.3 ± 2.5% to an average density of 0.68 g / cm3. This residue is characterized to be treated in an anaerobic batch reactor where it is recirculated leachate and studied the competing microorganisms in the anaerobic degradation of organic fraction of municipal solid waste. (author)

  7. Evaluation of Membrane Ultrafiltration and Residual Chlorination as a Decentralized Water Treatment Strategy for Ten Rural Healthcare Facilities in Rwanda.

    Science.gov (United States)

    Huttinger, Alexandra; Dreibelbis, Robert; Roha, Kristin; Ngabo, Fidel; Kayigamba, Felix; Mfura, Leodomir; Moe, Christine

    2015-10-27

    There is a critical need for safe water in healthcare facilities (HCF) in low-income countries. HCF rely on water supplies that may require additional on-site treatment, and need sustainable technologies that can deliver sufficient quantities of water. Water treatment systems (WTS) that utilize ultrafiltration membranes for water treatment can be a useful technology in low-income countries, but studies have not systematically examined the feasibility of this technology in low-income settings. We monitored 22 months of operation of 10 WTS, including pre-filtration, membrane ultrafiltration, and chlorine residual disinfection that were donated to and operated by rural HCF in Rwanda. The systems were fully operational for 74% of the observation period. The most frequent reasons for interruption were water shortage (8%) and failure of the chlorination mechanism (7%). When systems were operational, 98% of water samples collected from the HCF taps met World Health Organization (WHO) guidelines for microbiological water quality. Water quality deteriorated during treatment interruptions and when water was stored in containers. Sustained performance of the systems depended primarily on organizational factors: the ability of the HCF technician to perform routine servicing and repairs, and environmental factors: water and power availability and procurement of materials, including chlorine and replacement parts in Rwanda.

  8. Evaluation of Membrane Ultrafiltration and Residual Chlorination as a Decentralized Water Treatment Strategy for Ten Rural Healthcare Facilities in Rwanda

    Directory of Open Access Journals (Sweden)

    Alexandra Huttinger

    2015-10-01

    Full Text Available There is a critical need for safe water in healthcare facilities (HCF in low-income countries. HCF rely on water supplies that may require additional on-site treatment, and need sustainable technologies that can deliver sufficient quantities of water. Water treatment systems (WTS that utilize ultrafiltration membranes for water treatment can be a useful technology in low-income countries, but studies have not systematically examined the feasibility of this technology in low-income settings. We monitored 22 months of operation of 10 WTS, including pre-filtration, membrane ultrafiltration, and chlorine residual disinfection that were donated to and operated by rural HCF in Rwanda. The systems were fully operational for 74% of the observation period. The most frequent reasons for interruption were water shortage (8% and failure of the chlorination mechanism (7%. When systems were operational, 98% of water samples collected from the HCF taps met World Health Organization (WHO guidelines for microbiological water quality. Water quality deteriorated during treatment interruptions and when water was stored in containers. Sustained performance of the systems depended primarily on organizational factors: the ability of the HCF technician to perform routine servicing and repairs, and environmental factors: water and power availability and procurement of materials, including chlorine and replacement parts in Rwanda.

  9. Treatment of Residual Sodium and Sodium Potassium from Fast Reactors. Review of Recent Accomplishments, Challenges and Technologies

    International Nuclear Information System (INIS)

    2015-08-01

    In addition to the usual radiation and conventional hazards present during the decommissioning of disused nuclear installations, the presence of residual sodium or the alloy sodium potassium — used in primary, secondary and support systems in reactors using liquid metal as a coolant — presents additional technical, safety and cost challenges for decommissioning. This results from the propensity of these materials to react exothermically with water and moisture in the air potentially resulting in toxic and explosive reactionsThis publication discusses a variety of treatment methods to be considered when dismantling components that still contain residual quantities of sodium or sodium potassium, several of which were presented as contributed papers to the IAEA session during the 5. International Conference and Exhibition on Decommissioning Challenges, in Avignon, France, 7–11 April 2013. The publication provides a synthesis of information presented during the session, which was developed further at a consultants meeting held in Vienna, 2–6 December 2013. Decommissioning challenges faced at eight different facilities in five different countries are discussed, as well as the achievements and lessons learned that are of value to the worldwide decommissioning community

  10. Residual cervical lymphadenopathy after definitive treatment of nasopharyngeal carcinoma: fine needle aspiration cytology, computed tomography and histopathological findings.

    Science.gov (United States)

    Toh, S-T; Yuen, H-W; Lim, K-H; Goh, Y-H; Goh, H-K C

    2011-01-01

    Patients with nasopharyngeal carcinoma may have residual cervical lymphadenopathy after definitive treatment of the primary tumour and regional cervical nodal disease. Whether such lymphadenopathy truly represents persistent disease is unclear. There are few published studies addressing this clinical problem. We retrospectively and systematically reviewed the clinical records of 12 patients with nasopharyngeal carcinoma who had presented to a tertiary academic hospital, over an 11-year period, with suspected persistent cervical nodal disease after definitive radiotherapy or concurrent chemoradiotherapy. Findings on fine needle aspiration cytology and computed tomography scanning were correlated with final histopathological results. The incidence of negative neck dissection was 41.7 per cent. The positive and negative predictive values of fine needle aspiration cytology in identifying disease were 100 and 42.9 per cent, respectively. Computed tomography scanning had a positive predictive value of 58.3 per cent in identifying disease. In patients treated definitively for nasopharyngeal carcinoma, residual cervical lymphadenopathy may not represent persistent disease. Head and neck surgeons involved in the management of these patients should bear in mind the current limitations of fine needle aspiration cytology and computed tomography in confirming the diagnosis pre-operatively. Salvage neck dissection may over-treat some of these patients.

  11. High Combustion Research Facility

    Data.gov (United States)

    Federal Laboratory Consortium — At NETL's High-Pressure Combustion Research Facility in Morgantown, WV, researchers can investigate new high-pressure, high-temperature hydrogen turbine combustion...

  12. Combustion Research Laboratory

    Data.gov (United States)

    Federal Laboratory Consortium — The Combustion Research Laboratory facilitates the development of new combustion systems or improves the operation of existing systems to meet the Army's mission for...

  13. [Pre-prosthetics: role of the physiotherapist in the treatment of the residual limb and prosthetic preparation of the person].

    Science.gov (United States)

    Maffi, Alberto; Mulè, Chiara; Taveggia, Giovanni

    2015-01-01

    The rehabilitation of amputees requires a multi-discipline approach. Within the work of the team, physiotherapy plays a central role both in terms of the technical skills made available to the patient, as well as in terms of the psychological-motivational support offered to the amputee during treatment. The pre-prosthetic phase of rehabilitation is the beginning of a complex rehabilitative process during which starts with an assessment of the general clinical condition of the patient and their residual capacities, so as to develop personalised rehabilitative strategies based upon the needs of the amputee. This whole process aims to get the amputee standing with a prosthetic as quickly as possible, thus allowing the social reintegration of the amputee.

  14. Occurrence and seasonal variations of 25 pharmaceutical residues in wastewater and drinking water treatment plants.

    Science.gov (United States)

    Kot-Wasik, A; Jakimska, A; Śliwka-Kaszyńska, M

    2016-12-01

    Thousands of tons of pharmaceuticals are introduced into the aqueous environment due to their incomplete elimination during treatment process in wastewater treatment plants (WWTPs) and water treatment plants (WTPs). The presence of pharmacologically active compounds in the environment is of a great interest because of their potential to cause negative effects. Furthermore, drugs can undergo different processes leading to the formation of new transformation products, which may be more toxic than the parent compound. In light of these concerns, within the research a new, rapid and sensitive analytical procedure for the determination of a wide range of pharmaceuticals from different classes using solid phase extraction (SPE) and high-performance liquid chromatography tandem mass spectrometry (HPLC-MS/MS) technique in different water samples was developed. This methodology was applied to investigate the occurrence, removal efficiency of 25 pharmaceuticals during wastewater and drinking water treatment, and seasonal variability in the amount of selected pharmaceuticals in WWTP and WTP over a year. The most often detected analytes in water samples were carbamazepine (100 % of samples) and ibuprofen (98 % of samples), concluding that they may be considered as pollution indicators of the aqueous environment in tested area. Highly polar compound, metformin, was determined at very high concentration level of up to 8100 ng/L in analyzed water samples. Drugs concentrations were much higher in winter season, especially for non-steroidal inflammatory drugs (NSAIDs) and caffeine, probably due to the inhibited degradation related to lower temperatures and limited sunlight. Carbamazepine was found to be the most resistant drug to environmental degradation and its concentrations were at similar levels during four seasons.

  15. A study of dual polymer conditioning of aluminum-based drinking water treatment residual.

    Science.gov (United States)

    Ma, W; Zhao, Y Q; Kearney, P

    2007-06-01

    Conditioning of an aluminum-based water treatment sludge by single and dual polymers was investigated in this study. Capillary suction time (CST), specific resistance to filtration (SRF) and settling rate were used to evaluate the sludge dewatering characteristics. Sludge dewaterability resulting from single and dual polymer conditioning were compared for the purpose of exploring the validity and effectiveness of dual polymer conditioning strategy. Unlike activated sludge derived from wastewater treatment, results from this study have demonstrated that conditioning of the alum sludge by the combined use of an cationic polymer (FO-4140) followed by an anionic polymer (LT-25) does not exhibit considerable advantage in further improvement of sludge dewaterability with comparison of single polymer conditioning. This study supports the view that for aluminum-based water treatment sludge, inter particle bridging seems to be the dominative mechanism and the charge neutralization plays a less important role in the conditioning process. In addition, an intrinsic relationship between CST and SRF was deducted and tested via the experimental data obtained from the study.

  16. Assessment of engine cycle performances with synthes gas fuel addition based on determining coefficients in chemistry kinetics law through treatment of combustion speed

    OpenAIRE

    Gorbunov, A. V.; Viarshyna, H. A.; Pilatau, A.Y.; Baranov, V. Y.; Nozhenko, O. S.; Kaptug, A. Y.

    2013-01-01

    Assessment of engine cycle performances with synthes gas fuel addition based on determining coefficients in chemistry kinetics law through treatment of combustion speed / A. V. Gorbunov [et al.] // Наука – образованию, производству, экономике : материалы 11-й Международной научно-технической конференции. Т. 2. - Минск : БНТУ, 2013. - С. 58.

  17. Haplotype of platelet receptor P2RY12 gene is associated with residual clopidogrel on-treatment platelet reactivity.

    Science.gov (United States)

    Nie, Xiao-Yan; Li, Jun-Lei; Zhang, Yong; Xu, Yang; Yang, Xue-Li; Fu, Yu; Liang, Guang-Kai; Lu, Yun; Liu, Jian; Shi, Lu-Wen

    To investigate a possible association between common variations of the P2RY12 and the residual clopidogrel on-treatment platelet reactivity after adjusting for the influence of CYP2C19 tested by thromboelastography (TEG). One hundred and eighty patients with acute coronary syndrome (ACS) treated with clopidogrel and aspirin were included and platelet function was assessed by TEG. Five selected P2RY12 single nucleotide polymorphisms (SNPs; rs6798347, rs6787801, rs6801273, rs6785930, and rs2046934), which cover the common variations in the P2RY12 gene and its regulatory regions, and three CYP2C19 SNPs ( * 2, * 3, * 17) were genotyped and possible haplotypes were analyzed. The high on-treatment platelet reactivity (HTPR) prevalence defined by a platelet inhibition rate <30% by TEG in adenosine diphosphate (ADP)-channel was 69 (38.33%). Six common haplotypes were inferred from four of the selected P2RY12 SNPs (denoted H 0 to H 5 ) according to the linkage disequilibrium R square (except for rs2046934). Haplotype H 1 showed a significantly lower incidence of HTPR than the reference haplotype (H 0 ) in the total study population while haplotypes H 1 and H 2 showed significantly lower incidences of HTPR than H 0 in the nonsmoker subgroup after adjusting for CYP2C19 effects and demographic characteristics. rs2046934 (T744C) did not show any significant association with HTPR. The combination of common P2RY12 variations including regulatory regions rather than rs2046934 (T744C) that related to pharmacodynamics of clopidogrel in patients with ACS was independently associated with residual on-clopidogrel platelet reactivity. This is apart from the established association of the CYP2C19. This association seemed more important in the subgroup defined by smoking.

  18. Residues and source identification of persistent organic pollutants in farmland soils irrigated by effluents from biological treatment plants

    Energy Technology Data Exchange (ETDEWEB)

    Chen, Y.; Wang, C.X.; Wang, Z.J. [Chinese Academy of Science, Beijing (China). Ecoenvironmental Science Research Center

    2005-08-01

    Sewage and industrial effluents from biological treatment plant have been widely used for agricultural irrigation in north part of China. In the present study, field surveys were carried out in the farmlands irrigated by effluents from biological treatment plants that receive sewage wastewater and industrial discharges. Residues of polycyclic aromatic hydrocarbons (PAHs) and organochlorine pesticides (OCPs) in the soils irrigated using both ground water and effluents were compared. The origins of PAHs in the soils were discussed. The results showed that wastewater irrigation could cause accumulation of PAHs in soils close to the pollution discharge. Significantly higher concentrations of PAHs were observed in the sampling sites close to the entrance of main channel in contrast to those along branches and the reference sites. There was no significant relationship between the accumulation of persistent organic pollutants and organic matter content in soil (TOC). Soil contamination of these persistent organic pollutants as affected by effluent irrigation was characterized by the dominant accumulation of high-molecular-weight PAHs (HMW-PAHs). In the case study, concentration of benzo(a)pyrane (BaP, 45.6 ng/g), indeno(1,2,3-cd)pyrene (IcP, 86.3 ng/g), benzo(g,h,i)perlene (BgP, 66.9 ng/g) could exceed the limits of the soil quality standard for biodegraded soils. In identification of the sources, the IcP/BgP values of PAHs in soils were more close to that in air particulates from coal/coke source (1.09 {+-} 0.03 ng/g). Therefore, both of the PAHs residues in effluents and emission from a nearby coal/coke plant were responsible. Also in this case study, low levels of the OCPs were observed and were not of significant concern in this wastewater irrigation area.

  19. Combustion chemistry

    Energy Technology Data Exchange (ETDEWEB)

    Brown, N.J. [Lawrence Berkeley Laboratory, CA (United States)

    1993-12-01

    This research is concerned with the development and use of sensitivity analysis tools to probe the response of dependent variables to model input variables. Sensitivity analysis is important at all levels of combustion modeling. This group`s research continues to be focused on elucidating the interrelationship between features in the underlying potential energy surface (obtained from ab initio quantum chemistry calculations) and their responses in the quantum dynamics, e.g., reactive transition probabilities, cross sections, and thermal rate coefficients. The goals of this research are: (i) to provide feedback information to quantum chemists in their potential surface refinement efforts, and (ii) to gain a better understanding of how various regions in the potential influence the dynamics. These investigations are carried out with the methodology of quantum functional sensitivity analysis (QFSA).

  20. Effect of residual H2O2 from advanced oxidation processes on subsequent biological water treatment: A laboratory batch study.

    Science.gov (United States)

    Wang, Feifei; van Halem, Doris; Liu, Gang; Lekkerkerker-Teunissen, Karin; van der Hoek, Jan Peter

    2017-10-01

    H 2 O 2 residuals from advanced oxidation processes (AOPs) may have critical impacts on the microbial ecology and performance of subsequent biological treatment processes, but little is known. The objective of this study was to evaluate how H 2 O 2 residuals influence sand systems with an emphasis on dissolved organic carbon (DOC) removal, microbial activity change and bacterial community evolution. The results from laboratory batch studies showed that 0.25 mg/L H 2 O 2 lowered DOC removal by 10% while higher H 2 O 2 concentrations at 3 and 5 mg/L promoted DOC removal by 8% and 28%. A H 2 O 2 dosage of 0.25 mg/L did not impact microbial activity (as measured by ATP) while high H 2 O 2 dosages, 1, 3 and 5 mg/L, resulted in reduced microbial activity of 23%, 37% and 37% respectively. Therefore, DOC removal was promoted by the increase of H 2 O 2 dosage while microbial activity was reduced. The pyrosequencing results illustrated that bacterial communities were dominated by Proteobacteria. The presence of H 2 O 2 showed clear influence on the diversity and composition of bacterial communities, which became more diverse under 0.25 mg/L H 2 O 2 but conversely less diverse when the dosage increased to 5 mg/L H 2 O 2 . Anaerobic bacteria were found to be most sensitive to H 2 O 2 as their growth in batch reactors was limited by both 0.25 and 5 mg/L H 2 O 2 (17-88% reduction). In conclusion, special attention should be given to effects of AOPs residuals on microbial ecology before introducing AOPs as a pre-treatment to biological (sand) processes. Additionally, the guideline on the maximum allowable H 2 O 2 concentration should be properly evaluated. Copyright © 2017 The Author(s). Published by Elsevier Ltd.. All rights reserved.

  1. Comparison of liquid hot water, very dilute acid and alkali treatments for enhancing enzymatic digestibility of hazelnut tree pruning residues.

    Science.gov (United States)

    Sabanci, Kevser; Buyukkileci, Ali Oguz

    2018-04-05

    The effect of pretreatments on the composition of the hazelnut tree pruning residue (HTPR) and on the digestibility of the cellulose was investigated. The liquid hot water (LHW) and the very dilute acid (VDA) treatments were effective in solubilizing hemicellulose. The cellulose conversion increased up to around 60% (corresponding to 32-36 g/L glucose) with decreasing hemicellulose concentration in the pretreated HTPR. The alkali treatment provided partial delignification, however, the glucose production was comparably lower. Combining the hemicellulose removal and the delignification effect of different pretreatments in two-stage processes (LHW-alkali and VDA-alkali treatments) enhanced the cellulose concentration in the solids, but not the amount of glucose released in the enzymatic digestion. These results suggested that the hemicellulose was the main barrier against the conversion of cellulose in the LHW and VDA treated HTPR and the glucose in the hydrolysis medium inhibited the cellulase activity, which prevented the complete conversion of cellulose. Copyright © 2018 Elsevier Ltd. All rights reserved.

  2. Mechanical and interfacial properties of poly(vinyl chloride) based composites reinforced by cassava stillage residue with different surface treatments

    Science.gov (United States)

    Zhang, Yanjuan; Gan, Tao; Li, Qian; Su, Jianmei; Lin, Ye; Wei, Yongzuo; Huang, Zuqiang; Yang, Mei

    2014-09-01

    Cassava stillage residue (CSR), a kind of agro-industrial plant fiber, was modified by coupling agent (CA), mechanical activation (MA), and MA-assisted CA (MACA) surface treatments, respectively. The untreated and different surface treated CSRs were used to prepare plant fibers/polymer composites (PFPC) with poly(vinyl chloride) (PVC) as polymer matrix, and the properties of these CSR/PVC composites were compared. Surface treated CSR/PVC composites possessed better mechanical properties, water resistance and dimensional stability compared with the untreated CSR/PVC composite, attributing to the improvement of interfacial properties between CSR and PVC matrix. MACA-treated CSR was the best reinforcement among four types of CSRs (untreated, MA-treated, CA-treated, and MACA-treated CSRs) because MACA treatment led to the significant improvement of dispersion, interfacial adhesion and compatibility between CSR and PVC. MACA treatment could be considered as an effective and green method for enhancing reinforcement efficiency of plant fibers and the properties of PFPC.

  3. Coagulant Recovery from Water Treatment Residuals: A Review of Applicable Technologies

    Science.gov (United States)

    Keeley, J.; Jarvis, P.; Judd, S. J.

    2014-01-01

    Conventional water treatment consumes large quantities of coagulant and produces even greater volumes of sludge. Coagulant recovery (CR) presents an opportunity to reduce both the sludge quantities and the costs they incur, by regenerating and purifying coagulant before reuse. Recovery and purification must satisfy stringent potable regulations for harmful contaminants, while remaining competitive with commercial coagulants. These challenges have restricted uptake and lead research towards lower-gain, lower-risk alternatives. This review documents the context in which CR must be considered, before comparing the relative efficacies and bottlenecks of potential technologies, expediting identification of the major knowledge gaps and future research requirements. PMID:26064036

  4. Influence of post-harvest treatments with fludioxonil and soy lecithin co-application in controlling blue and grey mould and fludioxonil residues in Coscia pears.

    Science.gov (United States)

    Schirra, M; D'Aquino, S; Migheli, Q; Pirisi, F M; Angioni, A

    2009-01-01

    The residue levels of fludioxonil (FLU) were determined in Coscia pear following a 1-, 2- or 4-min dip in an aqueous mixture of FLU containing 300 or 100 mg l(-1) (active ingredient, a.i.) at 20 and 50 degrees C, respectively, with or without 2% soy lecithin. The efficacy of heat treatment with water and FLU mixtures was investigated on artificially inoculated pears for the control of post-harvest decay caused by blue (Penicillium expansum Link) and grey (Botrytis cinerea Pers. ex Fr.) mould. Treatment with 300 mg l(-1) FLU at 20 degrees C increased residues significantly when treatment time rose from 1 to 2 min; no further increase was recorded when dip time raised from 2 to 4 min. FLU residue rates were unaffected by treatment time when 300 mg l(-1) a.i. was applied in combination with lecithin at 20 degrees C. While treatment with 100 mg l(-1) a.i. at 50 degrees C for 1 and 2 min resulted in similar residue levels, significantly higher residues were detected when dip time increased from 1 to 4 min. Co-application of lecithin significantly decreased FLU residues with respect to fruit treated with FLU alone. Treatments with FLU at 20 or 50 degrees C effectively controlled decay over 10 days of incubation. While co-application of lecithin did not affect the efficacy of FLU at 300 mg l(-1)and 20 degrees C, treatment efficacy decreased when lecithin was applied in combination with 100 mg l(-1) FLU and 50 degrees C for 4 min and to a greater extent when dip time was 1-2 min.

  5. Coal Combustion Wastes Reuse in Low Energy Artificial Aggregates Manufacturing

    Directory of Open Access Journals (Sweden)

    Raffaele Cioffi

    2013-10-01

    Full Text Available Sustainable building material design relies mostly on energy saving processes, decrease of raw materials consumption, and increase of waste and by-products recycling. Natural and lightweight artificial aggregates production implies relevant environmental impact. This paper addresses both the issues of residues recycling and energy optimization. Particularly, three coal combustion wastes (Weathered Fly Ash, WFA; Wastewater Treatment Sludge, WTS; Desulfurization Device Sludge, DDS supplied by the Italian electric utility company (ENEL have been employed in the manufacture of cold bonded artificial aggregates. Previously, the residues have been characterized in terms of chemical and mineralogical compositions, water content, particle size distribution, and heavy metal release behavior. These wastes have been used in the mix design of binding systems with the only addition of lime. Finally, the artificial aggregates have been submitted to physical, mechanical, and leaching testing, revealing that they are potentially suitable for many civil engineering applications.

  6. Coal Combustion Wastes Reuse in Low Energy Artificial Aggregates Manufacturing.

    Science.gov (United States)

    Ferone, Claudio; Colangelo, Francesco; Messina, Francesco; Iucolano, Fabio; Liguori, Barbara; Cioffi, Raffaele

    2013-10-31

    Sustainable building material design relies mostly on energy saving processes, decrease of raw materials consumption, and increase of waste and by-products recycling. Natural and lightweight artificial aggregates production implies relevant environmental impact. This paper addresses both the issues of residues recycling and energy optimization. Particularly, three coal combustion wastes (Weathered Fly Ash, WFA; Wastewater Treatment Sludge, WTS; Desulfurization Device Sludge, DDS) supplied by the Italian electric utility company (ENEL) have been employed in the manufacture of cold bonded artificial aggregates. Previously, the residues have been characterized in terms of chemical and mineralogical compositions, water content, particle size distribution, and heavy metal release behavior. These wastes have been used in the mix design of binding systems with the only addition of lime. Finally, the artificial aggregates have been submitted to physical, mechanical, and leaching testing, revealing that they are potentially suitable for many civil engineering applications.

  7. Coal Combustion Wastes Reuse in Low Energy Artificial Aggregates Manufacturing

    Science.gov (United States)

    Ferone, Claudio; Colangelo, Francesco; Messina, Francesco; Iucolano, Fabio; Liguori, Barbara; Cioffi, Raffaele

    2013-01-01

    Sustainable building material design relies mostly on energy saving processes, decrease of raw materials consumption, and increase of waste and by-products recycling. Natural and lightweight artificial aggregates production implies relevant environmental impact. This paper addresses both the issues of residues recycling and energy optimization. Particularly, three coal combustion wastes (Weathered Fly Ash, WFA; Wastewater Treatment Sludge, WTS; Desulfurization Device Sludge, DDS) supplied by the Italian electric utility company (ENEL) have been employed in the manufacture of cold bonded artificial aggregates. Previously, the residues have been characterized in terms of chemical and mineralogical compositions, water content, particle size distribution, and heavy metal release behavior. These wastes have been used in the mix design of binding systems with the only addition of lime. Finally, the artificial aggregates have been submitted to physical, mechanical, and leaching testing, revealing that they are potentially suitable for many civil engineering applications. PMID:28788372

  8. Characterization using XRD of puzzolanic materials from residual sludge from water treatment

    Science.gov (United States)

    Barón, G.; Montaño, A. M.; González, C. P.

    2017-12-01

    The goal of this work is to do mechanical and chemical characterization of puzzolanic materials using compressive strength measurements and X-Ray Diffraction (XRD). These materials are composed of red clay and aluminous sludge produced by the treatment of potable water at Planta Algodonal, Ocaña, Norte de Santander, Colombia. Ceramic bricks were sintered to 1100°C and ten were characterized in their physically, mechanically and chemically properties. The results showed that the relationships with which the Colombian standards according to NTC 4017 (100KGF/cm2) for non-structural bricks are maintained for those containing 10% (105Kgf/cm2) and 20% (102.9Kgf/cm2) of sludge with respect to clay.

  9. Targeting glutamate system for novel antipsychotic approaches: relevance for residual psychotic symptoms and treatment resistant schizophrenia.

    Science.gov (United States)

    de Bartolomeis, Andrea; Sarappa, Chiara; Magara, Salvatore; Iasevoli, Felice

    2012-05-05

    Antipsychotics are the mainstay of schizophrenia treatment. However, approximately one third of schizophrenic patients do not respond or respond poorly to antipsychotics. Therefore, there is a need for new approaches that can improve schizophrenia treatment significantly. Promising strategies arise from the modulation of glutamatergic system, according to its proposed involvement in schizophrenia pathogenesis. In this review, we critically updated preclinical and clinical data on the modulation of glutamate N-methyl-D-aspartate (NMDA) receptor activity by NMDA-Rs co-agonists, glycine transporters inhibitors, AMPAkines, mGluR5 agonists, NMDA-Rs partial agonists. We focused on: 1) preclinical results in animal models mimicking the pathophysiology of psychosis, mainly believed to be responsible of negative and cognitive symptoms, and predicting antipsychotic-like activity of these compounds; and 2) clinical efficacy in open-label and double-blind trials. Albeit promising preclinical findings for virtually all compounds, clinical efficacy has not been confirmed for D-cycloserine. Contrasting evidence has been reported for glycine and D-serine, that may however have a role as add-on agents. More promising results in humans have been found for glycine transporter inhibitors. AMPAkines appear to be beneficial as pro-cognitive agents, while positive allosteric modulators of mGluR5 have not been tested in humans. Memantine has been proposed in early stages of schizophrenia, as it may counteract the effects of glutamate excitotoxicity correlated to high glutamate levels, slowing the progression of negative symptoms associated to more advanced stages of the illness. Copyright © 2012 Elsevier B.V. All rights reserved.

  10. Co-combustion of Fossil Fuels and Waste

    DEFF Research Database (Denmark)

    Wu, Hao

    and the utilization of a waste-derived material as an additive; 3) the combustion of a biomass residue rich in phosphorus. Co-combustion of coal and SRF was conducted in an entrained flow reactor (EFR). The work revealed that when coal was co-fired with up to 25 wt% SRF, the burnout and the emissions of SO2...

  11. Equation for Combustion Noise

    Science.gov (United States)

    Liu, T. M.

    1982-01-01

    Mathematical relationship derived for interactions between turbulent flame and combustion noise. Relationship is rigorous theoretical correlation of combustion noise and combustion process. Establishes foundation for acoustic measurements as tool for investigating structure of turbulent flames. Mathematical relationship is expected to aid researchers in field of noise generated by combustion.

  12. Residual tumour detection in post-treatment granulation tissue by using advanced diffusion models in head and neck squamous cell carcinoma patients.

    Science.gov (United States)

    Fujima, Noriyuki; Yoshida, Daisuke; Sakashita, Tomohiro; Homma, Akihiro; Kudo, Kohsuke; Shirato, Hiroki

    2017-05-01

    To evaluate the detectability of the residual tumour in post-treatment granulation tissue using parameters obtained with an advanced diffusion model in patients with head and neck squamous cell carcinoma (HNSCC) treated by chemoradiation therapy. We retrospectively evaluated 23 patients with HNSCC after the full course of chemoradiation therapy. The diffusion-weighted image (DWI) acquisition used single-shot spin-echo echo-planar imaging with 11 b-values (0-1000). We calculated 10 DWI parameters using a mono-exponential model, a bi-exponential model, a stretched exponential model (SEM), a diffusion kurtosis imaging (DKI) model and a statistical diffusion model (SDM) in the region of interest (ROI) placed on the post-treatment granulation tissue. The presence of residual tumour was determined by histological findings or clinical follow-up. Among the 23 patients, seven patients were revealed to have residual tumour. The univariate analysis revealed significant differences in six parameters between the patients with and without residual tumour. From the receiver operating characteristic curve analysis, the highest area under curve was detected in the center of the Gaussian distribution of diffusion coefficient (D s ) obtained by the SDM. The multivariate analysis revealed that the D s and diffusion heterogeneity (α) obtained by the SEM were predictors for the presence of residual tumour. DWI parameters obtained by advanced fitting models will be one of the diagnostic tools for the detection of residual tumour. Copyright © 2017 Elsevier B.V. All rights reserved.

  13. Towards a coherent European approach for taxation of combustible waste

    International Nuclear Information System (INIS)

    Dubois, Maarten

    2013-01-01

    Highlights: • Current European waste taxes do not constitute a level playing field. • Integrating waste incineration in EU ETS avoids regional tax competition. • A differentiated incineration tax is a second-best instrument for NO x emissions. • A tax on landfilled incineration residues stimulates ash treatment. - Abstract: Although intra-European trade of combustible waste has grown strongly in the last decade, incineration and landfill taxes remain disparate within Europe. The paper proposes a more coherent taxation approach for Europe that is based on the principle of Pigovian taxation, i.e. the internalization of environmental damage costs. The approach aims to create a level playing field between European regions while reinforcing incentives for sustainable management of combustible waste. Three important policy recommendations emerge. First, integrating waste incineration into the European Emissions Trading System for greenhouse gases (EU ETS) reduces the risk of tax competition between regions. Second, because taxation of every single air pollutant from waste incineration is cumbersome, a differentiated waste incineration tax based on NO x emissions can serve as a second-best instrument. Finally, in order to strengthen incentives for ash treatment, a landfill tax should apply for landfilled incineration residues. An example illustrates the coherence of the policy recommendations for incineration technologies with diverse environmental effects

  14. Residual manifestations of hypercortisolemia following surgical treatment in a patient with Cushing syndrome.

    Science.gov (United States)

    Bartz, Sara K; Karaviti, Lefkothea P; Brandt, Mary L; Lopez, Monica E; Masand, Prakash; Devaraj, Sridevi; Hicks, John; Anderson, Lauren; Lodish, Maya; Keil, Meg; Stratakis, Constantine A

    2015-01-01

    Cushing Syndrome is difficult to diagnose, and the comorbidities and persistent late effects of hypercortisolemia after treatment of the primary disease are challenging for the patient and the endocrinologist. To report the case of a girl with obesity and hypertension, ultimately diagnosed with Cushing syndrome due to primary pigmented nodular adrenocortical disease. In this case, the complications of hypercortisolism persisted short term despite surgical intervention. A 4 year old morbidly obese African-American girl with developmental delay presented with hypertensive emergency in the ER and 18-month history of progressive weight gain. Her previous history included premature adrenarche, hypertension, seizures and a random high cortisol with suppressed ACTH. She was subsequently stabilized, and a diagnostic work-up persistently demonstrated elevated cortisol and suppressed ACTH. An abdominal MRI showed bilateral adrenal multinodular disease, consistent with multinodular hyperplasia of the adrenal glands. Based on these findings the patient underwent a bilateral adrenalectomy, which confirmed primary pigmented nodular adrenocortical disease. The patient had a complicated, protracted post-operative course requiring adjustment of therapy for persistent hypertension. Two months after surgery, she was readmitted to the Emergency Department with hyperpyrexia and hypertension and succumbed to the complications of sepsis. This case highlights the significant diagnostic and therapeutic challenges in treating children with Cushing syndrome. Resolution of the source of hypercortisolemia does not imply regression of hypertension or recovery of the immune system. Although the child underwent bilateral adrenalectomy, persistent consequences of prolonged severe hypercortisolism contributed to her death two months later.

  15. Effect of conditioning by PAM polymers with different charges on the structural and characteristic evolutions of water treatment residuals.

    Science.gov (United States)

    Yan, W L; Wang, Y L; Chen, Y J

    2013-11-01

    Three types of polyacrylamide (PAM) flocculants with different charges (cationic PAM WD4960, nonionic PAM M351, and anionic PAM WDA110) were used for water treatment residuals (WTRs) conditioning, and the physicochemical, morphological and structural characteristics of raw and conditioned WTRs were investigated. Rheological methods were employed to analyze the internal structural transition between the raw and conditioned WTRs under a typical dosage of WD4960. Results showed that when the raw WTRs were conditioned with the polymers, the optimum dosage of WD4960 was 4.82 g/kg total suspended solid (TSS) while that of both M351 and WDA110 was 7.24 g/kg TSS. The residual PAM content in the supernatant of the WTR matrix conditioned at the optimum WD4960 dosage was 5.59 mg/L, which is the least among the supernatants obtained with the three types of PAM. Furthermore, the visible fulvic acid (FA) in the supernatant disappeared and the intensity of the ultraviolet FA decreased. The average diameter of irregularly shaped aggregates in the WTR suspensions increased from 35.73 μm to several hundred micrometers with increasing PAM dosage. The size of WTR aggregates conditioned at the optimum WD4960 dosage was much larger than that of aggregates obtained at the optimum M351 or WDA110 dosages. Two-dimensional fractal dimension (D2) values presented an increasing trend with increasing PAM dosage. D2 values of the conditioned WTR aggregates were 1.87, 1.76, and 1.83 at optimum WD4960, M351, and WDA110 dosages, respectively. The cationic PAM (CPAM) WD4960 thus appears to be a more ideal conditioner for WTRs. Consistent relationships were observed among the capillary suction time (CST), average particle size, and D2 values of the conditioned WTR aggregates at the optimum WD4960 dosage. Mass fractal dimensions (D(f)) indicated that both the raw and WD4960-conditioned WTRs behave like weak-link flocs/aggregates. D(f) values (log G'-log TSS) of the WTR aggregates before and after

  16. Effects of aluminium water treatment residuals, used as a soil amendment to control phosphorus mobility in agricultural soils.

    Science.gov (United States)

    Ulén, Barbro; Etana, Ararso; Lindström, Bodil

    2012-01-01

    Phosphorus (P) leaching from agricultural soils is a serious environmental concern. Application of aluminium water treatment residuals (Al-WTRs) at a rate of 20 Mg ha(-1) to clay soils from central Sweden significantly increased mean topsoil P sorption index (PSI) from 4.6 to 5.5 μmol kg(-1) soil. Mean degree of P saturation in ammonium lactate extract (DPS-AL) significantly decreased from 17 to 13%, as did plant-available P (P-AL). Concentrations of dissolved reactive P (DRP) decreased by 10-85% in leaching water with Al-WTR treatments after exposure of topsoil lysimeters to simulated rain. Soil aggregate stability (AgS) for 15 test soils rarely improved. Three soils (clay loam, silty loam and loam sand) were tested in greenhouse pot experiments. Aluminium-WTR application of 15 or 30 ton ha(-1) to loam sand and a clay loam with P-AL values of 80-100 mg kg(-1) soil significantly increased growth of Italian ryegrass when fertilised with P but did not significantly affect growth of spring barley on any soil. Al-WTR should only be applied to soils with high P fertility where improved crop production is not required.

  17. LCA Of The “Renescience” Concept: An Alternative To Incineration For The Treatment Of Residual Municipal Solid Waste

    DEFF Research Database (Denmark)

    Tonini, Davide; Astrup, Thomas

    2010-01-01

    be separated for recycling. In this study the environmental assessment of a number of scenarios for the “REnescience” concept is presented. The scenarios assessed are co-combustion of solid and liquid fraction in coal-fired power plants (CC-CC), co-combustion of the liquid fraction and incineration......The “REnescience” system consists on a pretreatment of the waste based on heat and enzymes which liquefy the biogenic fraction of the waste (paper and organics). The outputs of the process are then liquid slurry and a remaining solid fraction from which metals, plastic and glass can eventually...... of the solid fraction (CC-INC), anaerobic digestion of the liquid fraction to produce biogas and co-combustion of the solid fraction (BG-CC) and anaerobic digestion of the liquid fraction to produce biogas and incineration of the solid fraction (BG-INC). The reference technology for the comparison...

  18. In vitro and cellular activities of the selected fruits residues for skin aging treatment

    Directory of Open Access Journals (Sweden)

    NATTAYA LOURITH

    Full Text Available ABSTRACT Peel extracts of litchi and rambutan, and that of tamarind seed coat were investigated in relation to their utility in skin-aging treatments. Standardized extracts of tamarind were significantly (p < 0.05 more efficient at O2 •- scavenging (IC50 = 27.44 ± 0.09 than those of litchi and rambutan (IC50 = 29.57 ± 0.30 and 39.49 ± 0.52 μg/ml, respectively and the quercetin standard (IC50 = 31.88 ± 0.15 μg/ml. Litchi extract proved significantly (p < 0.05 more effective for elastase and collagenase inhibition (88.29 ± 0.25% and 79.46 ± 0.92%, respectively than tamarind (35.43 ± 0.68% and 57.69 ± 5.97% or rambutan (31.08 ± 0.38% and 53.99 ± 6.18%. All extracts were safe to human skin fibroblasts and inhibit MMP-2, with litchi extract showing significantly (p < 0.01 enhanced inhibition over the standard, vitamin C (23.75 ± 2.74% and 10.42 ± 5.91% at 0.05 mg/ml, respectively. Extracts suppress melanin production in B16F10 melanoma cells through inhibition of tyrosinase and TRP-2, with litchi extract being the most potent, even more so than kojic acid (standard. These results highlight the potential for adding value to agro-industrial waste, as the basis for the sustainable production of innovative, safe, anti-aging cosmetic products.

  19. Results of the treatment of keratocystic odontogenic tumours using enucleation and treatment of the residual bony defect with Carnoy's solution.

    Science.gov (United States)

    Leung, Y Y; Lau, S L; Tsoi, K Y Y; Ma, H L; Ng, C L

    2016-09-01

    This retrospective study aimed to investigate the recurrence rate of keratocystic odontogenic tumours (KCOTs) treated by enucleation and the application of Carnoy's solution, and to assess the surgical morbidities associated with this treatment. KCOTs treated using a standard protocol of enucleation and the application of Carnoy's solution between 1990 and 2013 were evaluated. One hundred and five KCOTS in 105 patients (54 male, 51 female) were analysed. The mean follow-up period was 86.6 months (range 24-313 months). The recurrence rate was 11.4%. A postoperative inferior alveolar nerve neurosensory deficit occurred in 30.1% of the mandibular cases, with 16% of these being permanent. The postoperative infection and fracture rates were 1.9% and 0.9%, respectively. Younger age, multilocular KCOTs, larger tumour size, and longer antero-posterior lesion length on the radiograph were found to be risk factors for recurrence. It is concluded that enucleation and the application of Carnoy's solution to treat KCOTs results in a relatively low recurrence rate and a low rate of surgical morbidities. Copyright © 2016 International Association of Oral and Maxillofacial Surgeons. Published by Elsevier Ltd. All rights reserved.

  20. Oxygen-enhanced combustion

    CERN Document Server

    Baukal, Charles E

    2013-01-01

    Combustion technology has traditionally been dominated by air/fuel combustion. However, two developments have increased the significance of oxygen-enhanced combustion-new technologies that produce oxygen less expensively and the increased importance of environmental regulations. Advantages of oxygen-enhanced combustion include less pollutant emissions as well as increased energy efficiency and productivity. Oxygen-Enhanced Combustion, Second Edition compiles information about using oxygen to enhance industrial heating and melting processes. It integrates fundamental principles, applications, a

  1. Association Between Pesticide Residue Intake From Consumption of Fruits and Vegetables and Pregnancy Outcomes Among Women Undergoing Infertility Treatment With Assisted Reproductive Technology.

    Science.gov (United States)

    Chiu, Yu-Han; Williams, Paige L; Gillman, Matthew W; Gaskins, Audrey J; Mínguez-Alarcón, Lidia; Souter, Irene; Toth, Thomas L; Ford, Jennifer B; Hauser, Russ; Chavarro, Jorge E

    2018-01-01

    Animal experiments suggest that ingestion of pesticide mixtures at environmentally relevant concentrations decreases the number of live-born offspring. Whether the same is true in humans is unknown. To examine the association of preconception intake of pesticide residues in fruits and vegetables (FVs) with outcomes of infertility treatment with assisted reproductive technologies (ART). This analysis included 325 women who completed a diet assessment and subsequently underwent 541 ART cycles in the Environment and Reproductive Health (EARTH) prospective cohort study (2007-2016) at a fertility center at a teaching hospital. We categorized FVs as having high or low pesticide residues using a validated method based on surveillance data from the US Department of Agriculture. Cluster-weighted generalized estimating equations were used to analyze associations of high- and low-pesticide residue FV intake with ART outcomes. Adjusted probabilities of clinical pregnancy and live birth per treatment cycle. In the 325 participants (mean [SD] age, 35.1 [4.0] y; body mass index, 24.1 [4.3]), mean (SD) intakes of high- and low-pesticide residue FVs were 1.7 (1.0) and 2.8 (1.6) servings/d, respectively. Greater intake of high-pesticide residue FVs was associated with a lower probability of clinical pregnancy and live birth. Compared with women in the lowest quartile of high-pesticide FV intake (women in the highest quartile (≥2.3 servings/d) had 18% (95% CI, 5%-30%) lower probability of clinical pregnancy and 26% (95% CI, 13%-37%) lower probability of live birth. Intake of low-pesticide residue FVs was not significantly related to ART outcomes. Higher consumption of high-pesticide residue FVs was associated with lower probabilities of pregnancy and live birth following infertility treatment with ART. These data suggest that dietary pesticide exposure within the range of typical human exposure may be associated with adverse reproductive consequences.

  2. Recycling of drinking water treatment residue as an additional medium in columns for effective P removal from eutrophic surface water.

    Science.gov (United States)

    Wang, Changhui; Wu, Yu; Bai, Leilei; Zhao, Yaqian; Yan, Zaisheng; Jiang, Helong; Liu, Xin

    2018-04-03

    This study assesses the feasibility of recycling drinking water treatment residue (DWTR) to treat eutrophic surface water in a one-year continuous flow column test. Heat-treated DWTR was used as an additional medium (2%-4%) in columns in case excessive organic matter and N were released from the DWTR to surface water. The results indicated that with minimal undesirable effects on other water properties, DWTR addition substantially enhanced P removal, rendering P concentrations in treated water oligotrophic and treated water unsuitable for Microcystis aeruginosa breeding. Long-term stable P removal by DWTR-column treatment was mainly attributed to the relatively low P levels in raw water (<0.108 mg L -1 ) and high P adsorption capability of DWTR, as confirmed by increases in amorphous Al/Fe in DWTR after the tests and low adsorption of P in the mobile forms. The major components of DWTR showed minimal changes, and potential metal pollution from DWTR was not a factor to consider during recycling. DWTR also enriched functional bacterial genera that benefitted biogeochemical cycles and multiple pollution control (e.g., Dechloromonas, Geobacter, Leucobacter, Nitrospira, Rhodoplanes, and Sulfuritalea); an apparent decrease in Mycobacterium with potential pathogenicity was observed in DWTR-columns. Regardless, limited denitrification of DWTR-columns was observed as a result of low bioavailability of C in surface water. This finding indicates that DWTR can be used with other methods to ensure denitrification for enhanced treatment effects. Overall, the use of DWTR as an additional medium in column systems can potentially treat eutrophic surface water. Copyright © 2018 Elsevier Ltd. All rights reserved.

  3. Efficacy of drinking-water treatment residual in controlling off-site phosphorus losses: a field study in Florida.

    Science.gov (United States)

    Agyin-Birikorang, S; Oladeji, O O; O'Connor, G A; Obreza, T A; Capece, J C

    2009-01-01

    Land application of drinking-water treatment residuals (WTR) has been shown to control excess soil soluble P and can reduce off-site P losses to surface and ground water. To our knowledge, no field study has directly evaluated the impacts of land application of WTRs on ground water quality. We monitored the effects of three organic sources of P (poultry manure, Boca Raton biosolids, Pompano biosolids) or triple superphosphate co-applied with an aluminum-based WTR (Al-WTR) on soil and ground water P and Al concentrations under natural field conditions for 20 mo in a soil with limited P sorption capacity. The P sources were applied at two rates (based on P or nitrogen [N] requirement of bahiagrass) with or without Al-WTR amendment and replicated three times. Without WTR application, applied P sources increased surface soil soluble P concentrations regardless of the P source or application rate. Co-applying the P sources with Al-WTR prevented increases in surface soil soluble P concentrations and reduced P losses to shallow ground water. Total dissolved P and orthophosphate concentrations of shallow well ground water of the N-based treatments were greater (>0.9 and 0.3 mg L(-1), respectively) in the absence than in the presence ( approximately 0.6 and 0.2 mg L(-1), respectively) of Al-WTR. The P-based application rate did not increase ground water P concentrations relative to background concentrations. Notwithstanding, Al-WTR amendment decreased ground water P concentrations from soil receiving treatments with P-based application rates. Ground water total dissolved Al concentrations were unaffected by soil Al-WTR application. We conclude that, at least for the study period, Al-WTR can be safely used to reduce P leaching into ground water without increasing the Al concentration of ground water.

  4. Residues of Avermectin B1a in rotational crops and soils following soil treatment with [14C]Avermectin B1a

    International Nuclear Information System (INIS)

    Moye, H.A.; Malagodi, M.H.; Yoh, H.; Leibee, G.L.; Ku, C.C.; Wislocki, P.G.

    1987-01-01

    [ 14 C]Avermectin B 1 a was applied twelve times to muck and sandy loam soils and three times to sandy soil at 0.025-0.030 lb/acre per application. These applications simulated the intended use of avermectin B 1 a on celery, vegetables, and cotton, respectively. Following three aging periods in each soil type, sorghum, lettuce, and carrot or turnip seeds were planted and harvested at one-fourth, half, and full size. Analysis of these crops by oxidative combustion demonstrated that crops grown in muck, sandy loam, and sandy soils contained radiolabeled residues ranging from below the limit of quantitation (BLQ) to 7.4 μg/kg of avermectin B 1 a equivalents, BLQ to 11.6 μg/kg, and BLQ to 3.54 μg/kg, respectively. There was a general trend of decreasing residue concentrations with increasing preharvest intervals in crops grown in all soils. The radioactivity present in muck and sandy loam soils disappeared with half-lives ranging from 103 to 267 days and from 102 to 132 days, respectively

  5. Fate of Ah receptor agonists during biological treatment of an industrial sludge containing explosives and pharmaceutical residues.

    Science.gov (United States)

    Gustavsson, Lillemor K; Klee, Nina; Olsman, Helena; Hollert, Henner; Engwall, Magnus

    2004-01-01

    Sweden is meeting prohibition for deposition of organic waste from 2005. Since 1 million tons of sludge is produced every year in Sweden and the capacity for incineration does not fill the demands, other methods of sludge management have to be introduced to a higher degree. Two biological treatment alternatives are anaerobic digestion and composting. Different oxygen concentrations result in different microbial degradation pathways and, consequently, in a different quality of the digestion or composting residue, It is therefore necessary to study sludge treatment during different oxygen regimes in order to follow both degradation of compounds and change in toxicity. In this study, an industrial sludge containing explosives and pharmaceutical residues was treated with anaerobic digestion or composting, and the change in toxicity was studied. Nitroaromatic compounds, which are the main ingredients of both pharmaceutical and explosives, are well known to cause cytotoxicity and genotoxicity. However, little data are available concerning sludge with nitroaromatics and any associated dioxin-like activity. Therefore, we studied the sludge before and after the treatments in order to detect any changes in levels of Ah receptor (AhR) agonists using two bioassays for dioxin-like compounds. An industrial sludge was treated with anaerobic digestion or composting in small reactors in a semi-continuous manner. The same volume as the feeding volume was taken out daily and stored at -20 degrees C. Sample preparation for the bioassays was done by extraction using organic solvents, followed by clean up with silica gel or sulphuric acid, yielding two fractions. The fractions were dissolved in DMSO and tested in the bioassays. The dioxin-like activity was measured using the DR-CALUX assay with transfected H4IIE rat hepatoma pGudluc cells and an EROD induction assay with RTL-W1 rainbow trout liver cells. The bioassays showed that the sludge contained AhR agonists at levels of TCDD

  6. Combustion 2000

    Energy Technology Data Exchange (ETDEWEB)

    A. Levasseur; S. Goodstine; J. Ruby; M. Nawaz; C. Senior; F. Robson; S. Lehman; W. Blecher; W. Fugard; A. Rao; A. Sarofim; P. Smith; D. Pershing; E. Eddings; M. Cremer; J. Hurley; G. Weber; M. Jones; M. Collings; D. Hajicek; A. Henderson; P. Klevan; D. Seery; B. Knight; R. Lessard; J. Sangiovanni; A. Dennis; C. Bird; W. Sutton; N. Bornstein; F. Cogswell; C. Randino; S. Gale; Mike Heap

    2001-06-30

    . To achieve these objectives requires a change from complete reliance of coal-fired systems on steam turbines (Rankine cycles) and moving forward to a combined cycle utilizing gas turbines (Brayton cycles) which offer the possibility of significantly greater efficiency. This is because gas turbine cycles operate at temperatures well beyond current steam cycles, allowing the working fluid (air) temperature to more closely approach that of the major energy source, the combustion of coal. In fact, a good figure of merit for a HIPPS design is just how much of the enthalpy from coal combustion is used by the gas turbine. The efficiency of a power cycle varies directly with the temperature of the working fluid and for contemporary gas turbines the optimal turbine inlet temperature is in the range of 2300-2500 F (1260-1371 C). These temperatures are beyond the working range of currently available alloys and are also in the range of the ash fusion temperature of most coals. These two sets of physical properties combine to produce the major engineering challenges for a HIPPS design. The UTRC team developed a design hierarchy to impose more rigor in our approach. Once the size of the plant had been determined by the choice of gas turbine and the matching steam turbine, the design process of the High Temperature Advanced Furnace (HITAF) moved ineluctably to a down-fired, slagging configuration. This design was based on two air heaters: one a high temperature slagging Radiative Air Heater (RAH) and a lower temperature, dry ash Convective Air Heater (CAH). The specific details of the air heaters are arrived at by an iterative sequence in the following order:-Starting from the overall Cycle requirements which set the limits for the combustion and heat transfer analysis-The available enthalpy determined the range of materials, ceramics or alloys, which could tolerate the temperatures-Structural Analysis of the designs proved to be the major limitation-Finally the commercialization

  7. An environmentally safe treatment scheme for gases to be produced in the in situ combustion pilot project (Mucura District, Orinoco belt, Venezuela)

    Energy Technology Data Exchange (ETDEWEB)

    Perozo, H.; Sena, A.; Vasquez, P.; Harner, R. [PDVSA Petroleos de Venezuela SA, Caracas (Venezuela, Bolivarian Republic of). INTEVEP

    2009-07-01

    The in situ combustion pilot project (ISCPP) to be conducted in the Bare field, in the Orinoco oil belt of Venezuela is a technological project lead by Petroleos de Venezuela (PDVSA) Intevep together with the Exploration and Production Division of Faja. The project is expected to increase the recovery factor to values between 20 and 60 per cent. By its execution, it is expected that relevant quantities of gases such as sulphur dioxide (SO{sub 2}), hydrogen sulphide (H{sub 2}S), and carbon monoxide (CO) will be produced. These gases require proper treatment to meet Venezuelan environmental standards. It was therefore necessary to develop a taylor made scheme in order to adjust the process for the environmentally safe management of noxious gases according to a non-producing-waste approach. This paper described the experimental methodology and laboratory results that led to the development of an environmentally sound flue gas treatment system that could be scaled up for the ISCPP. The paper discussed the thermal oxidation process and flue gas desulphurization. The laboratory tests regarding thermal oxidation were also discussed. The preparation of the gas mixture and results were then presented. The laboratory tests conducted by PDVSA Intevep demonstrated that at 300 degrees Celsius or more, a high yield of H{sub 2}S to SO{sub 2} conversion can be achieved. 5 refs., 6 tabs., 4 figs., 1 appendix.

  8. Reduced NOX combustion method

    International Nuclear Information System (INIS)

    Delano, M.A.

    1991-01-01

    This patent describes a method for combusting fuel and oxidant to achieve reduced formation of nitrogen oxides. It comprises: It comprises: heating a combustion zone to a temperature at least equal to 1500 degrees F.; injecting into the heated combustion zone a stream of oxidant at a velocity within the range of from 200 to 1070 feet per second; injecting into the combustion zone, spaced from the oxidant stream, a fuel stream at a velocity such that the ratio of oxidant stream velocity to fuel stream velocity does not exceed 20; aspirating combustion gases into the oxidant stream and thereafter intermixing the aspirated oxidant stream and fuel stream to form a combustible mixture; combusting the combustible mixture to produce combustion gases for the aspiration; and maintaining the fuel stream substantially free from contact with oxidant prior to the intermixture with aspirated oxidant

  9. Gaseous emissions from sewage sludge combustion in a moving bed combustor.

    Science.gov (United States)

    Batistella, Luciane; Silva, Valdemar; Suzin, Renato C; Virmond, Elaine; Althoff, Chrtistine A; Moreira, Regina F P M; José, Humberto J

    2015-12-01

    Substantial increase in sewage sludge generation in recent years requires suitable destination for this residue. This study evaluated the gaseous emissions generated during combustion of an aerobic sewage sludge in a pilot scale moving bed reactor. To utilize the heat generated during combustion, the exhaust gas was applied to the raw sludge drying process. The gaseous emissions were analyzed both after the combustion and drying steps. The results of the sewage sludge characterization showed the energy potential of this residue (LHV equal to 14.5 MJ kg(-1), db) and low concentration of metals, polycyclic aromatic hydrocarbons (PAH), polychlorinated dibenzo-p-dioxins (PCDD) and polychlorinated dibenzofurans (PCDF). The concentration of CO, NOx, BTEX (benzene, toluene, ethylbenzene and xylenes) emitted from the sludge combustion process were lower than the legal limits. The overall sludge combustion and drying process showed low emissions of PCDD/PCDF (0.42 ng I-TEQ N m(-3)). BTEX and PAH emissions were not detected. Even with the high nitrogen concentration in the raw feed (5.88% db), the sludge combustion process presented NOx emissions below the legal limit, which results from the combination of appropriate feed rate (A/F ratio), excess air, and mainly the low temperature kept inside the combustion chamber. It was found that the level of CO emissions from the overall sludge process depends on the dryer operating conditions, such as the oxygen content and the drying temperature, which have to be controlled throughout the process in order to achieve low CO levels. The aerobic sewage sludge combustion process generated high SO2 concentration due to the high sulfur content (0.67 wt%, db) and low calcium concentration (22.99 g kg(-1)) found in the sludge. The high concentration of SO2 in the flue gas (4776.77 mg N m(-3)) is the main factor inhibiting PCDD/PCDF formation. Further changes are needed in the pilot plant scheme to reduce SO2 and particulate matter emissions

  10. The financial feasibility of delivering forest treatment residues to bioenergy facilities over a range of diesel fuel and delivered biomass prices

    Science.gov (United States)

    Greg Jones; Dan Loeffler; Edward Butler; Susan Hummel; Woodam. Chung

    2013-01-01

    Forest treatments have the potential to produce significant quantities of forest residue biomass, which includes the tops and limbs from merchantable trees and smaller trees removed to meet management objectives. We spatially analyzed the sensitivity of financially feasible biomass volumes for delivery to a bioenergy facility across 16 combinations of delivered biomass...

  11. Patient preferences for clean intermittent catheterisation and transurethral indwelling catheterisation for treatment of abnormal post-void residual bladder volume after vaginal prolapse surgery

    NARCIS (Netherlands)

    Hakvoort, R. A.; Nieuwkerk, P. T.; Burger, M. P.; Emanuel, M. H.; Roovers, J. P.

    2011-01-01

    To determine patient preferences for clean intermittent catheterisation (CIC) relative to transurethral indwelling catheterisation (TIC) as the treatment of abnormal post-void residual bladder volume (PVR) following vaginal prolapse surgery. Scenario-based preference assessment during face-to-face

  12. Veterinary treatment of cows with isoxsuprine for a caesarian section may temporarily lead to residues in hair of both cow and calf

    NARCIS (Netherlands)

    Groot, M.J.; Lasaroms, J.J.P.; Hende, van J.; Nielen, M.W.F.

    2012-01-01

    Isoxsuprine is a beta-agonist that can be used for growth promotion in cattle, but it is also used as registered veterinary medicine. To investigate if veterinary treatment of cows could lead to residues of isoxsuprine in the hair of their newborn calves, an animal experiment was performed. Four

  13. 26 CFR 1.860E-1 - Treatment of taxable income of a residual interest holder in excess of daily accruals.

    Science.gov (United States)

    2010-04-01

    ... 26 Internal Revenue 9 2010-04-01 2010-04-01 false Treatment of taxable income of a residual interest holder in excess of daily accruals. 1.860E-1 Section 1.860E-1 Internal Revenue INTERNAL REVENUE SERVICE, DEPARTMENT OF THE TREASURY (CONTINUED) INCOME TAX (CONTINUED) INCOME TAXES Real Estate Investment...

  14. Efficacy of heat treatments with water and fludioxonil for postharvest control of blue and gray molds on inoculated pears and fludioxonil residues in fruit.

    Science.gov (United States)

    Schirra, Mario; D'Aquino, Salvatore; Mulas, Maurizio; Melis, Rita Anna Maria; Giobbe, Sara; Migheli, Quirico; Garau, Anna; Angioni, Alberto; Cabras, Paolo

    2008-05-01

    The residue levels of fludioxonil (FLU) were determined in pear cultivars Precoce di Fiorano, Coscia, and Spadona estiva after a 2-min dip in an aqueous mixture of FLU containing 300 or 100 mg/liter of active ingredient at 20 or 50 degrees C and after 12 days at 17 degrees C and 80% relative humidity (simulated shelf life conditions). The accumulation trend of FLU residues was determined in 'Precoce di Fiorano' pears after treatments with 25, 50, 100, or 200 mg/liter of active ingredient at 20 or 50 degrees C for 2 min or at 60 degrees C for 1 min. The efficacy of heat treatments with water and FLU was investigated on artificially inoculated 'Precoce di Fiorano', 'Coscia', and 'Spadona estiva' pears for the control of postharvest blue mold and gray mold caused by Penicillium expansum and Botrytis cinerea, respectively. Treatment with 300 mg/liter FLU at 20 degrees C resulted in residue levels similar to those from treatment with 100 mg/liter FLU at 50 degrees C in 'Coscia' fruit but in significantly lower residues in 'Precoce di Fiorano' and 'Spadona estiva' pears. Post-shelf life residues decreased in all cultivars, especially in 'Spadona estiva' pears treated with 300 mg/liter FLU at 20 degrees C. Residue levels of FLU in 'Precoce di Fiorano' pears treated at 20, 50, or 60 degrees C were correlated with fungicide dosage. When an equal rate was used, treatment at 50 degrees C resulted in a higher and a notably higher FLU deposition than that found under treatment at 60 and 20 degrees C, respectively. The in vitro tests showed that both pathogens were very sensitive to FLU, with MICs averaging 0.05 and 0.1 mg/liter for B. cinerea and P. expansum isolates, respectively. The 50% effective concentration ranged between 0.01 and 0.05 mg/liter for B. cinerea and between 0.05 and 0.1 mg/liter for P. expansum. In the in vivo trials, hot water treatment effectively reduced the incidence of both diseases during the first 4 to 8 days, depending on cultivar, dip temperature

  15. Lanthanum-modified drinking water treatment residue for initial rapid and long-term equilibrium phosphorus immobilization to control eutrophication.

    Science.gov (United States)

    Wang, Changhui; Wu, Yu; Wang, Youquan; Bai, Leilei; Jiang, Helong; Yu, Juhua

    2018-06-15

    This study presents an approach for developing inactivating materials to achieve an initial rapid and a long-term equilibrium P immobilization to control eutrophication based on drinking water treatment residue (DWTR), which is a byproduct of potable water production. By taking advantage of the long-term equilibrium P adsorption by DWTR, the La chemical properties, and the previous success of using La-modified bentonite clay (Phoslock ® ), we used DWTR as a La carrier with different ratios to develop the specific materials. The La loading mechanisms, the potentially toxic effect of La-modified DWTR on snail Bellamya aeruginosa (within 120 d), and the short- and long-term (within 80 d) P immobilization characteristics of the modified DWTR were investigated to understand the performance of the developed materials. The results showed that La loading into DWTR was based on ligand exchanges and the formation of new particles; DWTR loaded with <5% La had no toxicity against the snail. Most importantly, the loading of 5% La to DWTR substantially enhanced the rapid immobilization capacity of DWTR, achieving an initial rapid and a long-term equilibrium P adsorption in aqueous solutions. This study promotes the beneficial recycling of DWTR and results in a win-win situation for lake restoration. Copyright © 2018 Elsevier Ltd. All rights reserved.

  16. Quantification of heavy metals from residual waste and ashes from the treatment plant of residual water Reciclagua and,effects for the health of those workers which manipulate those residuals; Cuantificacion de metales pesados de lodo residual y cenizas de la planta tratadora de aguas residuales Reciclagua y efectos a la salud de los trabajadores que manipulan los residuos

    Energy Technology Data Exchange (ETDEWEB)

    Guerrero D, J.J

    2004-07-01

    In this work, the technique of leaching using thermostatted column in series is applied, the X-ray diffraction for the identification of the atomic and molecular structure of the toxic metals that are present in the residual muds of the water treatment plant located in the municipality of Lerma Estado de Mexico, named RECICLAGUA, likewise the technique is used of emission spectrometry for plasma and X-ray fluorescence for the qualitative analysis. Its were take samples of residual mud and of incinerated mud of the treatment plant of residual waters of the industrial corridor Toluca -Lerma RECICLAGUA, located in Lerma Estado de Mexico. For this study there were mixed 100 g of residual mud with a solution to 10% of mineral acid or sodium hydroxide according to the case, to adjust the one pH at 2, 5, 7 and 10, it was added bisulfite, of 0.3-1.5 g of dodecyl sulfate sodium and 3.939 of DTPA (triple V) (Diethylene triamine pentaacetate). To this mud and ashes were extracted the toxic and valuable metals by means of the leaching technique using thermostatted columns placed in series that were designed by the Dr. Jaime Vite Torres; it is necessary to make mention that so much the process as the equipment with those that work it was patented by the same one. With the extraction of these metals benefits are obtained, mainly of economic type, achieving the decrease of the volume of those wastes that have been generated; as well as the so much the use of those residuals, once the metals have been eliminated, as of those liquors where the metals were extracted. It was carried out a quantitative analysis using emission spectrometry by plasma in solids by this way to be able to know the content of the present metals in the sample before and later of leaching them, these results reported a great quantity of elements. Another of the techniques employees was the X-ray diffraction analysis that provides an elementary content of the samples, identifying elements that are present in

  17. A productivity and cost comparison of two systems for producing biomass fuel from roadside forest treatment residues

    Science.gov (United States)

    Nathaniel Anderson; Woodam Chung; Dan Loeffler; John Greg Jones

    2012-01-01

    Forest operations generate large quantities of forest biomass residues that can be used for production of bioenergy and bioproducts. However, a significant portion of recoverable residues are inaccessible to large chip vans, making use financially infeasible. New production systems must be developed to increase productivity and reduce costs to facilitate use of these...

  18. Dilute alkali and hydrogen peroxide treatment of microwave liquefied rape straw residue for the extraction of cellulose nanocrystals

    Science.gov (United States)

    Xingyan Huang; Cornelis F. De Hoop; Feng Li; Jiulong Xie; Chung-Yun Hse; Jinqiu Qi; Yongze Jiang; Yuzhu Chen

    2017-01-01

    Microwave-assisted liquefaction of rape straw in methanol was conducted to collect the liquefied residues for the extraction of cellulose nanocrystals (CNCs).The liquefied residue with content of 23.44% from 180∘C/7.5 min was used to fibrillate CNCs with dilute alkali (2% NaOH) and hydrogen peroxide (5% H2O2...

  19. Improved inventory for heavy metal emissions from stationary combustion plants

    DEFF Research Database (Denmark)

    Nielsen, Malene; Nielsen, Ole-Kenneth; Hoffmann, Leif

    -2009. The report also include methodology, references and an uncertainty estimate. In Denmark, stationary combustion plants are among the most important emission sources for heavy metals. Emissions of all heavy metals have decreased considerably (73 % - 92 %) since 1990. The main HM emission sources are coal...... combustion, waste incineration, residual oil combustion and in 2009 also combustion of biomass. The emission from waste incineration plants has decreased profoundly also in recent years due to installation and improved performance of flue gas cleaning devices. The emission from power plants have also...

  20. Aging effects on reactivity of an aluminum-based drinking-water treatment residual as a soil amendment.

    Science.gov (United States)

    Agyin-Birikorang, S; O'Connor, G A

    2009-01-01

    Several studies have shown that drinking-water treatment residuals (WTR) could be used to control mobility of excess phosphorus (P) and other oxyanions in poorly sorbing soils. Presently, only "aged" WTRs (those left, or manipulated, to dewater) are land applied. However, if demand for WTRs increase in the near future, freshly-generated WTRs could be considered for land application. To our knowledge, few studies have examined the reactivity and equilibration time of freshly-generated alum-based WTR (Al-WTR). A laboratory thermal incubation study was, therefore, conducted to determine various extractable Al forms in Al-WTR as a function of WTR "age", and the time required for freshly generated Al-WTR to stabilize. Freshly-generated Al-WTR samples were collected directly from the discharge pumps of a drinking-water treatment plant, and thermally incubated at 52 degrees C, either with or without moisture control, for or = 6 mo. Aluminum reactivity of the freshly-generated Al-WTR decreased with time. At least 6 wk of thermal incubation (corresponding to > or = 6 mo of field drying) was required to stabilize the most reactive Al form (5mM oxalate extractable Al concentration) of the Al-WTR. Although no adverse Al-WTR effects have been reported on plants and grazing animals (apparently because of low availability of free Al(3+) in Al-WTR), land application of freshly-generated Al-WTRs (at least, those with similar physicochemical characteristics as the one utilized for the study) should be avoided.

  1. Short communication: use of the BetaStar Plus assay for detection of ceftiofur antimicrobial residues in milk from individual cows following intramammary treatment for mastitis.

    Science.gov (United States)

    Grooms, D L; Norby, B; Grooms, K E; Jagodzinski, E N; Erskine, R J; Halbert, L W; Coetzee, J F; Wulf, L; Rice, J A

    2015-09-01

    Development and use of on-farm assays to detect antimicrobial residues in milk is important to reduce the risk of violative residues in marketed milk. The objective of this study was to evaluate the effectiveness of a lateral-flow immunodiagnostic assay (BetaStar Plus, Neogen Corp., Lansing, MI) in detecting ceftiofur residues in milk from individual cows treated for mastitis. This assay is currently approved by the US Federal Drug Administration (FDA) for detecting β-lactam residues in commingled milk. Forty-five dairy cows with clinical mastitis from 4 dairy farms were enrolled and treated intramammary with 125 mg of ceftiofur hydrochloride (Spectramast LC, Zoetis, Madison, NJ) according to the manufacturer's label recommendation. Composite milk samples were collected (A) before first intramammary antimicrobial treatment, (B) before the last intramammary antimicrobial treatment, (C) the last milking of the product-labeled milk withhold, (D) the first milking after the product-labeled milk withhold had been met, and (E) 72 h after the product-labeled milk withhold had been met. Samples were tested using the BetaStar Plus assay within 48 h of collection. Parallel samples were analyzed by liquid chromatography-tandem mass spectrometry (LC-MS/MS) and for somatic cell count and milk components. The BetaStar Plus assay identified 6.7, 60.0, 46.7, 22.2, and 6.7% positive samples at each of the respective time points. The assay had sensitivity and specificity of 100 and 84.7%, respectively, compared with liquid chromatography-tandem mass spectrometry analysis using FDA published residue tolerance levels for ceftiofur (or ceftiofur metabolites) as a threshold. The BetaStar Plus assay could be useful for detecting ceftiofur residues in milk from individual cows following intramammary treatment for mastitis before the milk is shipped for processing. Copyright © 2015 American Dairy Science Association. Published by Elsevier Inc. All rights reserved.

  2. Specifics of phytomass combustion in small experimental device

    Directory of Open Access Journals (Sweden)

    Lenhard Richard

    2015-01-01

    Full Text Available A wood pellet combustion carries out with high efficiency and comfort in modern pellet boilers. These facts help to increase the amount of installed pellet boilers in households. The combustion process quality depends besides the combustion conditions also on the fuel quality. The wood pellets, which don`t contain the bark and branches represent the highest quality. Because of growing pellet demand, an herbal biomass (phytomass, which is usually an agricultural by-product becomes economically attractive for pellet production. Although the phytomass has the net calorific value relatively slightly lower than the wood biomass, it is often significantly worse in view of the combustion process and an emission production. The combustion of phytomass pellets causes various difficulties in small heat sources, mainly due to a sintering of fuel residues. We want to avoid the ash sintering by a lowering of temperature in the combustion chamber below the ash sintering temperature of phytomass via the modification of a burner design. For research of the phytomass combustion process in the small boilers is constructed the experimental combustion device. There will investigate the impact of cooling intensity of the combustion chamber on the combustion process and emissions. Arising specific requirements from the measurement will be the basis for the design of the pellet burner and for the setting of operating parameters to the trouble-free phytomass combustion was guaranteed.

  3. Method of processing combustible nuclear waste material

    International Nuclear Information System (INIS)

    Allen, C.R.; Greenhalgh, W.O.; Cowan, R.G.

    1982-01-01

    In treating combustible radio-waste which may contain volatile radio nuclides, e.g. Ru, the waste is heated and agitated with concentrated sulphuric acid, and the resulting residue which comprises elemental carbon which retains the volatile radio-nuclides is separated from the acid. Compounds which form borosilicate glass may be added to the waste, and after removal of sulphate, the resulting residual mixture may be fused into a glass. If the sulphate is not removed from the borosilicate mix, the residual mixture produces a ceramic product on heating. (author)

  4. Co-combustion of sewage sludge; Mitverbrennung von Klaerschlamm

    Energy Technology Data Exchange (ETDEWEB)

    Thome-Kozmiensky, K.J. [Technische Univ. Berlin (Germany). Fachgebiet Abfallwirtschaft

    1998-09-01

    Thermal sewage disposal pursues the following aims: destruction of organic pollutants contained in the sludge; concentration and removal or almost complete fixation of inorganic pollutants in the residue matrix; minimisation of the mass solid residue; production of useful products; utilisation of the caloric content. The thermal treatment chain should be as short as possible; intermediate stages in separate reactors such as digestion, drying, degasification or gasification should be avoided if the material is ultimately to be combusted. The present paper examines and assesses the co-combustion of sewage sludge. [Deutsch] Mit der thermischen Klaerschlammentsorgung werden folgende Ziele verfolgt: - Zerstoerung der im Schlamm enthaltenen organischen Schadstoffe, - Konzentration und Ausschleusung oder weitestgehende Fixierung der anorganischen Schadstoffe in die Reststoffmatrix, - Minimierung der Masse an festen Restabfaellen, - Herstellung verwertbarer Produkte, - Nutzung des Waermeeinhalts. Die thermische Behandlungskette sollte moeglichst kurz sein; Zwischenschritte wie Faulung, Trocknung, Ent- oder Vergasung in getrennten Reaktoren sollten vermieden werden, wenn letztendlich doch verbrannt wird. Das Verfahren der Mitverbrennung von Klaerschlamm wird hier untersucht und bewertet. (orig./SR)

  5. Treatment of waste incinerator air-pollution-control residues with FeSO4: Laboratory investigation of design parameters

    DEFF Research Database (Denmark)

    Jensen, Dorthe Lærke; Christensen, Thomas Højlund; Lundtorp, Kasper

    2002-01-01

    The key design parameters of a new process for treatment of air-pollution-control (APC) residues (the Ferroxprocess) were investigated in the laboratory. The optimisation involved two different APC-residues from actual incinerator plants. The design parameters considered were: amount of iron oxide...... that an optimum process configuration could be obtained yielding a stabilised solid product with low leaching of heavy metals and a dischargable wastewater with high contents of salts (in order to remove salts from the solid product) and low concentrations of heavy metals. The amount of iron added to the APC...

  6. Effect of Different Intrauterine Oxytetracycline Treatment on Reproductive Performance of Dairy Cows with Clinical Endometritis and Determination of Oxytetracycline Residues in Milk

    Directory of Open Access Journals (Sweden)

    Meysam MAKKI

    2016-05-01

    Full Text Available Main objective of this study was to determine whether intrauterine infusion of oxytetracycline (OTC is an appropriate method for the treatment of postpartum endometritis in dairy cows or not. To this end, 280 lactating Holstein cows with clinical signs of endometritis were randomly assigned into three treatment groups and 186 cows were sampled for cytology experiment. In group 1 (n=73 cows were treated with intrauterine infusion of 5 g/cow 10% OTC. In group 2 (n=44, before intrauterine OTC treatment, caudal epidural anesthesia was used to eliminate straining. In group 3 (n=49 after intrauterine infusion of 5g/cow 10% OTC, 100 ml of normal saline was injected to reduce the concentration of OTC and 20 untreated cows were assigned into control group (group 4. Clinical treatment rates were 79.4%, 68.1%, 65.3 %and 50% in OTC, OTC and caudal epidural anesthesia (OTC+CEA, OTC+Serum and control groups, respectively (P>0.05. Cytological treatment rate in each experiment group was significantly higher than the cytological treatment rate in control group in the second examination (P<0.05. To find out OTC residues in milk by high performance liquid chromatography (HPLC method, milk samples of 6 treated cows from each group were collected randomly 12, 24, 48, 72 and 96 hours after treatment. Maximum amounts of OTC residues were found 72 hours after treatment in all treatment groups. To evaluate the reproductive performance, the researchers compared 280 cows of treatment groups were compared with 1088 cows that were clinically healthy without any signs of clinical endometritis. The reproductive performance of the two groups were not significantly different, except days to first service which was lower in cows without clinical endometritis (P<0.05. According to the cytology study and the presence of antibiotic residues in milk samples at different times, the use of intrauterine OTC for treatment of clinical endometritis seems skeptical.

  7. Dioxines, furans and other pollutants emissions bond to the combustion of natural and additive woods

    International Nuclear Information System (INIS)

    Collet, S.

    2000-02-01

    This report deals especially on the dioxines and furans bond to the combustion of wood in industrial furnaces and domestic furnaces. It aims to define the environmental strategy which would allow the combustion of wood residues to produce energy. The first part recalls general aspects concerning the wood. The six other parts presents the wood resources and wastes, the additive used, the combustion and the different factors of combustion and finally the pollutants emissions. (A.L.B.)

  8. Combustion Research Facility

    Data.gov (United States)

    Federal Laboratory Consortium — For more than 30 years The Combustion Research Facility (CRF) has served as a national and international leader in combustion science and technology. The need for a...

  9. Particle Emissions from Biomass Combustion

    Energy Technology Data Exchange (ETDEWEB)

    Szpila, Aneta; Bohgard, Mats [Lund Inst. of Technology (Sweden). Div. of Ergonomics and Aerosol Technology; Strand, Michael; Lillieblad, Lena; Sanati, Mehri [Vaexjoe Univ. (Sweden). Div. of Bioenergy Technology; Pagels, Joakim; Rissler, Jenny; Swietlicki, Erik; Gharibi, Arash [Lund Univ. (Sweden). Div. of Nuclear Physics

    2003-05-01

    We have shown that high concentrations of fine particles of the order of 2-7x10{sup -7} particles per cm{sup 3} are being formed in all the combustion units studied. There was a higher difference between the units in terms of particle mass concentrations. While the largest differences was found for gas-phase constituents (CO and THC) and polyaromatic hydrocarbons. In 5 out of 7 studied units, multi-cyclones were the only measure for flue-gas separation. The multicyclones had negligible effect on the particle number concentration and a small effect on the mass of particles smaller than 5 {mu}m. The separation efficiency was much higher for the electrostatic precipitators. The boiler load had a dramatic influence on the coarse mode concentration during combustion of forest residue. PM0.8-6 increased from below 5 mg/m{sup 3} to above 50 mg/m{sup 3} even at a moderate change in boiler load from medium to high. A similar but less pronounced trend was found during combustion of dry wood. PM0.8-PM6 increased from 12 to 23 mg/m{sup 3} when the load was changed from low to high. When increasing the load, the primary airflow taken through the grate is increased; this itself may lead to a higher potential of the air stream to carry coarse particles away from the combustion zone. Measurements with APS-instrument with higher time-resolution showed a corresponding increase in coarse mode number concentration with load. Additional factor influencing observed higher concentration of coarse mode during combustion of forest residues, could be relatively high ash content in this type of fuel (2.2 %) in comparison to dry wood (0.3 %) and pellets (0.5 %). With increasing load we also found a decrease in PM1 during combustion of forest residue. Whether this is caused by scavenging of volatilized material by the high coarse mode concentration or a result of a different amount of volatilized material available for formation of fine particles needs to be shown in future studies. The

  10. Graf Type-IV Hips Have a Higher Risk of Residual Acetabular Dysplasia at 1 Year of Age Following Successful Pavlik Harness Treatment for Developmental Hip Dysplasia.

    Science.gov (United States)

    Novais, Eduardo N; Sanders, Julia; Kestel, Lauryn A; Carry, Patrick M; Meyers, Mariana L

    2016-09-22

    We asked whether patient-specific factors and ultrasound (US) measurements of hip dysplasia severity at initial examination influence short-term residual acetabular dysplasia in patients successfully treated with Pavlik harness for developmental hip dysplasia. After IRB approval, 134 hips (84 patients) successfully treated by the Pavlik method between August 2011 and October 2014 with follow-up at 12 months of age were identified. Early successful treatment was defined as normal examination and US after approximately 12 weeks of Pavlik treatment. Multivariate linear and logistic regression models were used to identify factors associated with acetabular index (AI) measurements at 12 months as well as factors associated with an increase in AI between the 6- and 12-month timepoints (dysplastic progression). The study consisted of 134 hips (84 patients). The distribution of dysplastic, Barlow, and Ortolani hips was 44.8% (N=60), 30.6% (N=41), and 24.6% (N=33), respectively. The crude incidence of residual dysplasia at the 6-month visit (AI>30 degrees) was 11.7% (12/102). The incidence of residual dysplasia at the 12-month visit (AI>28 degrees) was 11.8% (13/111). Graf type was the only variable associated with AI values at the 12-month visit (mean difference: Graf type-IV-Other, 2.6; 95% confidence interval, 0.3-4.9; P=0.026). The risk of residual acetabular dysplasia after normal hip US following Pavlik treatment is not negligible. Radiographic surveillance is warranted to monitor and screen for dysplasia progression. Patients with dislocated Graf type-IV hips at diagnosis are at increased risk of residual acetabular dysplasia at 1 year after successful treatment with the Pavlik method. Level III-therapeutic study.

  11. Improvement of the management of residual waste in areas without thermal treatment facilities: A life cycle analysis of an Italian management district

    Energy Technology Data Exchange (ETDEWEB)

    Di Maria, Francesco, E-mail: francesco.dimaria@unipg.it [LAR Laboratory, Dipartimento di Ingegneria, Via G. Duranti 93, Perugia (Italy); Micale, Caterina; Morettini, Emanuela [LAR Laboratory, Dipartimento di Ingegneria, Via G. Duranti 93, Perugia (Italy); Sisani, Luciano [TSA spa, Via Case Sparse 107, Magione (Italy); Damiano, Roberto [GESENU spa, Via della Molinella 7, Perugia (Italy)

    2015-10-15

    Highlights: • LCA analysis of two option for residual waste management. • Exploitation of mechanical physical sorting facility for extracting recyclable from RMSW. • Processing the mechanically sorted organic fraction in bioreactor landfill. • Sensitivity analysis demonstrate high influence for impact assessment of substitution ratio for recycle materials. - Abstract: Starting from an existing waste management district without thermal treatment facilities, two different management scenarios for residual waste were compared by life cycle assessment (LCA). The adoption of a bioreactor landfill for managing the mechanically sorted organic fraction instead of bio-stabilization led to reduction of global warming and fresh water eutrophication by 50% and 10%, respectively. Extraction of recyclables from residual waste led to avoided emissions for particulate matter, acidification and resource depletion impact categories. Marginal energy and the amount of energy recovered from landfill gas marginally affected the LCA results. On the contrary the quality of the recyclables extracted can significantly modify the eco profile of the management schemes.

  12. Improvement of the management of residual waste in areas without thermal treatment facilities: A life cycle analysis of an Italian management district

    International Nuclear Information System (INIS)

    Di Maria, Francesco; Micale, Caterina; Morettini, Emanuela; Sisani, Luciano; Damiano, Roberto

    2015-01-01

    Highlights: • LCA analysis of two option for residual waste management. • Exploitation of mechanical physical sorting facility for extracting recyclable from RMSW. • Processing the mechanically sorted organic fraction in bioreactor landfill. • Sensitivity analysis demonstrate high influence for impact assessment of substitution ratio for recycle materials. - Abstract: Starting from an existing waste management district without thermal treatment facilities, two different management scenarios for residual waste were compared by life cycle assessment (LCA). The adoption of a bioreactor landfill for managing the mechanically sorted organic fraction instead of bio-stabilization led to reduction of global warming and fresh water eutrophication by 50% and 10%, respectively. Extraction of recyclables from residual waste led to avoided emissions for particulate matter, acidification and resource depletion impact categories. Marginal energy and the amount of energy recovered from landfill gas marginally affected the LCA results. On the contrary the quality of the recyclables extracted can significantly modify the eco profile of the management schemes

  13. Four weeks of treatment with liraglutide reduces insulin dose without loss of glycemic control in type 1 diabetic patients with and without residual beta-cell function

    DEFF Research Database (Denmark)

    Kielgast, Urd; Krarup, Thure; Holst, Jens Juul

    2011-01-01

    OBJECTIVE To investigate the effect of 4 weeks of treatment with liraglutide on insulin dose and glycemic control in type 1 diabetic patients with and without residual ß-cell function. RESEARCH DESIGN AND METHODS Ten type 1 diabetic patients with residual ß-cell function (C-peptide positive) and 19.......1]; P Treatment with liraglutide in type 1 diabetic patients reduces insulin dose with improved or unaltered glycemic control....... activity was performed before (week 0) and during (week 4) treatment. Differences in insulin dose; HbA(1c); time spent with blood glucose 10, and 3.9-9.9 mmol/L; and body weight were evaluated. RESULTS Insulin dose decreased from 0.50 ± 0.06 to 0.31 ± 0.08 units/kg per day (P

  14. Theoretical Adiabatic Temperature and Chemical Composition of Sodium Combustion Flame

    International Nuclear Information System (INIS)

    Okano, Yasushi; Yamaguchi, Akira

    2003-01-01

    Sodium fire safety analysis requires fundamental combustion properties, e.g., heat of combustion, flame temperature, and composition. We developed the GENESYS code for a theoretical investigation of sodium combustion flame.Our principle conclusions on sodium combustion under atmospheric air conditions are (a) the maximum theoretical flame temperature is 1950 K, and it is not affected by the presence of moisture; the uppermost limiting factor is the chemical instability of the condensed sodium-oxide products under high temperature; (b) the main combustion product is liquid Na 2 O in dry air condition and liquid Na 2 O with gaseous NaOH in moist air; and (c) the chemical equilibrium prediction of the residual gaseous reactants in the flame is indispensable for sodium combustion modeling

  15. Insecticide treated curtains and residual insecticide treatment to control Aedes aegypti: An acceptability study in Santiago de Cuba.

    Science.gov (United States)

    Pérez, Dennis; Van der Stuyft, Patrick; Toledo, María Eugenia; Ceballos, Enrique; Fabré, Francisco; Lefèvre, Pierre

    2018-01-01

    Within the context of a field trial conducted by the Cuban vector control program (AaCP), we assessed acceptability of insecticide-treated curtains (ITCs) and residual insecticide treatment (RIT) with deltamethrin by the community. We also assessed the potential influence of interviewees' risk perceptions for getting dengue and disease severity. We embedded a qualitative study using in-depth interviews in a cluster randomized trial (CRT) testing the effectiveness of ITCs and RIT in Santiago de Cuba. In-depth interviews (N = 38) were conducted four and twelve months after deployment of the tools with people who accepted the tools, who stopped using them and who did not accept the tools. Data analysis was deductive. Main reasons for accepting ITCs at the start of the trial were perceived efficacy and not being harmful to health. Constraints linked to manufacturer instructions were the main reason for not using ITCs. People stopped using the ITCs due to perceived allergy, toxicity and low efficacy. Few heads of households refused RIT despite the noting reasons for rejection, such as allergy, health hazard and toxicity. Positive opinions of the vector control program influenced acceptability of both tools. However, frequent insecticide fogging as part of routine AaCP vector control actions diminished perceived efficacy of both tools and, therefore, acceptability. Fifty percent of interviewees did feel at risk for getting dengue and considered dengue a severe disease. However, this did not appear to influence acceptability of ITCs or RIT. Acceptability of ITCs and RIT was linked to acceptability of AaCP routine vector control activities. However, uptake and use were not always an indication of acceptability. Factors leading to acceptability may be best identified using qualitative methods, but more research is needed on the concept of acceptability and its measurement.

  16. Effect of solution chemistry on arsenic sorption by Fe- and Al-based drinking-water treatment residuals.

    Science.gov (United States)

    Nagar, Rachana; Sarkar, Dibyendu; Makris, Konstantinos C; Datta, Rupali

    2010-02-01

    Drinking-water treatment residual (WTR) have been proposed as a low-cost alternative sorbent for arsenic (As) - contaminated aquatic and soil systems. However, limited information exists regarding the effect of solution chemistry on As sorption by WTR. A batch incubation study was carried out to investigate the effect of solution pH (3-9) on As(V) sorption by Al- and Fe-based WTR as a function of solid: solution ratio (SSR) and initial As concentration. The effect of competing ligands (phosphate-P(V) and sulfate), and complexing metal (calcium) on As(V) sorption envelopes at the optimum SSR (200gL(-1)) was also evaluated. At 200gL(-1) SSR, maximum As(V) sorption ( approximately 100%) exhibited by the Fe-WTR was limited at the pH range of 3-7, whereas, the Al-WTR demonstrated approximately 100% As(V) sorption in the entire pH range. The negative pH effect on As(V) sorption became more pronounced with increasing initial As concentrations and decreasing SSR. Sorption of As(V) by surfaces of both WTR decreased in the presence of P(V), exhibiting strong pH dependence. Only for the Fe-WTR, increased dissolved iron concentrations at pH>7 supported a Fe-hydroxide reductive dissolution mechanism to account for the enhanced As sorption at alkaline pH. Addition of sulfate did not influence As(V) sorption by both WTR. A cooperative effect of calcium on As(V) sorption was observed at alkaline pH due to the formation of a calcium-arsenate phase. The constant capacitance model provided reasonable fits to the sorption envelope data for both single ion and binary ion (As and P) systems, but it was unable to explain the enhanced As sorption by the Fe-WTR at pH>7.

  17. Insecticide treated curtains and residual insecticide treatment to control Aedes aegypti: An acceptability study in Santiago de Cuba.

    Directory of Open Access Journals (Sweden)

    Dennis Pérez

    2018-01-01

    Full Text Available Within the context of a field trial conducted by the Cuban vector control program (AaCP, we assessed acceptability of insecticide-treated curtains (ITCs and residual insecticide treatment (RIT with deltamethrin by the community. We also assessed the potential influence of interviewees' risk perceptions for getting dengue and disease severity.We embedded a qualitative study using in-depth interviews in a cluster randomized trial (CRT testing the effectiveness of ITCs and RIT in Santiago de Cuba. In-depth interviews (N = 38 were conducted four and twelve months after deployment of the tools with people who accepted the tools, who stopped using them and who did not accept the tools. Data analysis was deductive. Main reasons for accepting ITCs at the start of the trial were perceived efficacy and not being harmful to health. Constraints linked to manufacturer instructions were the main reason for not using ITCs. People stopped using the ITCs due to perceived allergy, toxicity and low efficacy. Few heads of households refused RIT despite the noting reasons for rejection, such as allergy, health hazard and toxicity. Positive opinions of the vector control program influenced acceptability of both tools. However, frequent insecticide fogging as part of routine AaCP vector control actions diminished perceived efficacy of both tools and, therefore, acceptability. Fifty percent of interviewees did feel at risk for getting dengue and considered dengue a severe disease. However, this did not appear to influence acceptability of ITCs or RIT.Acceptability of ITCs and RIT was linked to acceptability of AaCP routine vector control activities. However, uptake and use were not always an indication of acceptability. Factors leading to acceptability may be best identified using qualitative methods, but more research is needed on the concept of acceptability and its measurement.

  18. Study of atmospheric emissions from liquid and solid fuels burning facilities and from raw phosphate chemical treatment in Sfax City (Tunisia); Etude des residus de combustion des fuels liquide et solide et de traitement chimique du phosphate brut dans la ville de Sfax (Tunisie)

    Energy Technology Data Exchange (ETDEWEB)

    Azri, Ch; Tili, A.; Serbaji, M.M. [Faculte des Sciences de Sfax, Dept. des Sciences de la Terre, Sfax (Tunisia); Medhioub, K. [Institut Preparatoire aux Etudes d' Ingenieurs de Sfax (IPEIS), Sfax (Tunisia)

    2002-07-01

    Study of atmospheric emissions from solid and liquid fuels burning facilities and from chemical treatment processes of raw phosphate in Sfax City (Tunisia) shows different forms of pollution concerning mainly sulfur oxides (SO{sub x}), sulfuric and phosphoric acid mists, fluorinated compounds and dust. Limited performances of amortized and/or over used de-pollution systems can explain high atmospheric emissions above emission limits. Gaseous pollution has been shown as coming mainly from phosphate treatment processes inside the chemical complex 'SIAPE' while particulate pollution is coming from all specific industries (SIAPE, charcoal facilities and weaving and soap factories). Calculated emission factors of these industries for some heavy metals (Pb, Cd, Ni, Cu, Zn) are very different. They are ranging from 0.3 to 9.5 g/t for phosphate treatment residues. Excepted Ni with 15.5 g/t, they are rather small for heavy fuels combustion residues. It, nevertheless, exceeds the emission factor of Ni for the phosphate treatment process. Volumes of emissions and calculated annual fluxes of metals are showing that 'SIAPE' could be a potential source of atmospheric pollution in the city. Its contribution to metal emissions is really exceeding emissions from well identified heavy fuels burning facilities in the city. Just to compare, Ni emissions from its processes are equal to emissions from 38 heavy fuels burning facilities of 4.8 t/day capacity (Ni 1 046 kg/year instead of 27 kg/year). Such a fact is clearly pointing out the high level of anthropogenic pollution from chemical processes adopted for primary matter transformation. They hence should be fitted with suitable de-pollution systems. (authors)

  19. Neonicotinoid insecticide residues in soil dust and associated parent soil in fields with a history of seed treatment use on crops in southwestern Ontario.

    Science.gov (United States)

    Limay-Rios, Victor; Forero, Luis Gabriel; Xue, Yingen; Smith, Jocelyn; Baute, Tracey; Schaafsma, Arthur

    2016-02-01

    Using neonicotinoid insecticides as seed treatments is a common practice in field crop production. Exposure of nontarget organisms to neonicotinoids present in various environmental matrices is debated. In the present study, concentrations of neonicotinoid residues were measured in the top 5 cm of soil and overlying soil surface dust before planting in 25 commercial fields with a history of neonicotinoid seed treatment use in southwestern Ontario in 2013 and 2014 using liquid chromatography-electrospray ionization tandem mass spectrometry. The mean total concentrations were 3.05 ng/g and 47.84 ng/g in 2013 and 5.59 ng/g and 71.17 ng/g in 2014 for parent soil and soil surface dust, respectively. When surface and parent soil residues were compared the mean concentration in surface dust was 15.6-fold and 12.7-fold higher than that in parent soil in 2013 and 2014, respectively. Pooled over years, the surface dust to parent soil ratio was 13.7, with mean concentrations of 4.36 ng/g and 59.86 ng/g for parent soil and surface dust, respectively. The present study's results will contribute important knowledge about the role these residues may play in the overall risk assessment currently under way for the source, transport, and impact of neonicotinoid insecticide residues in a maize ecosystem. © 2015 SETAC.

  20. Large breast size as a risk factor for late adverse effects of breast radiotherapy: Is residual dose inhomogeneity, despite 3D treatment planning and delivery, the main explanation?

    International Nuclear Information System (INIS)

    Goldsmith, Christy; Haviland, Joanne; Tsang, Yat; Sydenham, Mark; Yarnold, John

    2011-01-01

    Background and Purpose: Large breast size is associated with an increased risk of late adverse effects after breast conservation surgery and radiotherapy, even when 3D dosimetry is used. The purpose of this study is to test the hypothesis that residual dose inhomogeneity is sufficient to explain the association. Methods: Patients previously treated after breast conservation surgery with whole breast radiotherapy using 3D dosimetry and followed up in the UK FAST hypofractionation trial were selected for this analysis. The residual level of dose inhomogeneity across the whole breast treatment volume was used to test for association between residual dosimetry and post-treatment change in breast appearance at 2 years post-radiotherapy. Results: At 2 years, 201/279 (72%) of women had no change in photographic breast appearance, 61 (22%) had mild change and 17 (6%) had marked change. Breast size and dosimetry were both significantly associated with late effects in univariate analyses, but only breast size remained an independent significant risk factor for change in breast appearance when included in a multiple regression model together with other prognostic factors (p = 0.006 for trend). Conclusion: Large-breasted women are more likely to suffer change in breast size and shape after whole breast radiotherapy delivered using 3D dosimetry, but residual dose inhomogeneity is insufficient to explain the association.

  1. Criterion for the selection of a system of treatment of residues and their application to the wine of the alcoholic industry

    International Nuclear Information System (INIS)

    Caicedo M, Luis Alfonso; Fonseca, Jose Joaquin; Rodriguez, Gerardo

    1996-01-01

    The selection of a system of residues treatment should follow the criterion of the process denominated BATEA (better available and feasible technical and economical process). Because their application is difficult for not having objective parameters of evaluation, a method is presented that classifies the evaluation criterions in general and specific. For the quantification of these aspects factors like FQO are used, FCI, FTR, FD and the factor of applicability of the treatment (FAT). The method applied to the wine; allows concluding that it is the evaporation the best treatment system for this process, while other systems are not developed or it increases the recompensing rate

  2. Modeling the internal combustion engine

    Science.gov (United States)

    Zeleznik, F. J.; Mcbride, B. J.

    1985-01-01

    A flexible and computationally economical model of the internal combustion engine was developed for use on large digital computer systems. It is based on a system of ordinary differential equations for cylinder-averaged properties. The computer program is capable of multicycle calculations, with some parameters varying from cycle to cycle, and has restart capabilities. It can accommodate a broad spectrum of reactants, permits changes in physical properties, and offers a wide selection of alternative modeling functions without any reprogramming. It readily adapts to the amount of information available in a particular case because the model is in fact a hierarchy of five models. The models range from a simple model requiring only thermodynamic properties to a complex model demanding full combustion kinetics, transport properties, and poppet valve flow characteristics. Among its many features the model includes heat transfer, valve timing, supercharging, motoring, finite burning rates, cycle-to-cycle variations in air-fuel ratio, humid air, residual and recirculated exhaust gas, and full combustion kinetics.

  3. Uncertainties in hydrogen combustion

    International Nuclear Information System (INIS)

    Stamps, D.W.; Wong, C.C.; Nelson, L.S.

    1988-01-01

    Three important areas of hydrogen combustion with uncertainties are identified: high-temperature combustion, flame acceleration and deflagration-to-detonation transition, and aerosol resuspension during hydrogen combustion. The uncertainties associated with high-temperature combustion may affect at least three different accident scenarios: the in-cavity oxidation of combustible gases produced by core-concrete interactions, the direct containment heating hydrogen problem, and the possibility of local detonations. How these uncertainties may affect the sequence of various accident scenarios is discussed and recommendations are made to reduce these uncertainties. 40 references

  4. Fuel and Combustion Characteristics of Organic Wastes

    Science.gov (United States)

    Namba, Kunihiko; Ida, Tamio

    From a viewpoint of environmental preservation and resource protection, the recycling of wastes has been promoting. Expectations to new energy resource are growing by decrease of fossil fuel. Biomass is one of new energies for prevent global warning. This study is an attempt to burn biomass lamps made from residues in order to thermally recycle waste products of drink industries. The pyrolytic properties of shochu dregs and used tea leaves were observed by thermo-gravimertic analysis (TG) to obtained fundamental data of drink waste pyrolysis. It observed that shochu dregs pyrolyze under lower temperature than used tea leaves. These wastes were compressed by hot press apparatus in the temperature range from 140 to 180 °C for use as Bio-fuel (BF). The combustion behavior of BF was observed in fall-type electric furnace, where video-recording was carried out at sequential steps, such as ignition, visible envelope flame combustion and char combustion to obtain combustion characteristics such as ignition delay, visible flame combustion time and char combustion time.

  5. Weld repair practices without post weld heat treatment for ferritic alloys and their consequences on residual stresses: A review

    International Nuclear Information System (INIS)

    Aloraier, A.; Al-Mazrouee, A.; Price, J.W.H.; Shehata, T.

    2010-01-01

    The use of the half-bead, temper bead welding (TBW), and cold repair techniques is proving to reduce the cost of repairs and extend the life of aged components in power plants, petrochemical and hydrocarbon processing industries. It has been a significant area of interest for more than twenty years. A critical factor in this context is residual stress. The presence of residual stresses can lead to cracking which ultimately results in structural failure. This paper reviews the half-bead, TBW, and cold repair technique practices and their consequences on residual stresses within the nuclear, power, refinery and petrochemical industries and some of the contributions made by our group of researchers in this area. This paper reviews recent work by the Monash University group. We report our work on TBW residual stresses when measured using neutron diffraction which shows very little reduction in residual stresses over normally completed welds. The use of automatic FCAW has been explored in our group and is reported.

  6. New class of combustion processes

    International Nuclear Information System (INIS)

    Merzhanov, A.G.; Borovinskaya, I.P.

    1975-01-01

    A short review is given of the results of work carried out since 1967 on studying the combustion processes caused by the interaction of chemical elements in the condensed phase and leading to the formation of refractory compounds. New phenomena and processes are described which are revealed when investigating the combustion of the systems of this class, viz solid-phase combustion, fast combustion in the condensed phase, filtering combustion, combustion in liquid nitrogen, spinning combustion, self-oscillating combustion, and repeated combustion. A new direction in employment of combustion processes is discussed, viz. a self-propagating high-temperature synthesis of refractory nitrides, carbides, borides, silicides and other compounds

  7. Opportunities in pulse combustion

    Science.gov (United States)

    Brenchley, D. L.; Bomelburg, H. J.

    1985-10-01

    In most pulse combustors, the combustion occurs near the closed end of a tube where inlet valves operate in phase with the pressure amplitude variations. Thus, within the combustion zone, both the temperature and the pressure oscillate around a mean value. However, the development of practical applications of pulse combustion has been hampered because effective design requires the right combination of the combustor's dimensions, valve characteristics, fuel/oxidizer combination, and flow pattern. Pulse combustion has several additional advantages for energy conversion efficiency, including high combustion and thermal efficiency, high combustion intensity, and high convective heat transfer rates. Also, pulse combustion can be self-aspirating, generating a pressure boost without using a blower. This allows the use of a compact heat exchanger that may include a condensing section and may obviate the need for a chimney. In the last decade, these features have revived interest in pulse combustion research and development, which has resulted in the development of a pulse combustion air heater by Lennox, and a pulse combustion hydronic unit by Hydrotherm, Inc. To appraise this potential for energy savings, a systematic study was conducted of the many past and present attempts to use pulse combustion for practical purposes. The authors recommended areas where pulse combustion technology could possibly be applied in the future and identified areas in which additional R and D would be necessary. Many of the results of the study project derived from a special workshop on pulse combustion. This document highlights the main points of the study report, with particular emphasis on pulse combustion application in chemical engineering.

  8. Effect of microwave postpolymerization treatment on residual monomer content and the flexural strength of autopolymerizing reline resin.

    Science.gov (United States)

    Patil, Padmakar S; Chowdhary, Ramesh; Mandokar, Rashmi B

    2009-01-01

    Microwave postpolymerization has been suggested as a method to improve the flexural strength of an autopolymerizing denture reline resin. However, the effect of microwave postpolymerization on the residual monomer content and its influence on flexural strength have not been investigated. This study analyzed the effect of microwave postpolymerization on the residual monomer content and its influence on the flexural strength of an autopolymerizing reline resin (Denture Liner). A total of 70 specimens (64 Chi 10 Chi 3.3 mm) were polymerized according to the manufacturer's instructions and divided into 7 groups (n = 10). Control group specimens were not subjected to any further processing. Before testing, the specimens were subjected to postpolymerization in a microwave oven using different power (550 and 650 W) and time (3, 4, and 5 min) settings. Two specimens of each group were then manually ground into fine powder and samples extracted from the specimens using reflux method. The samples were then subjected to gas chromatography for residual monomer determination in area%. Eight specimens were subjected to a three-point bending device with a span of 50 mm and crosshead speed of 5 mm/min, and the flexural strength was determined in MPa. Data analyses included Student's t-test and one-way analysis of variance. For the Denture Liner reline resin, the residual monomer content decreased and the flexural strength increased significantly with the application of microwave irradiation using different time/power combinations. The specimens with the lowest residual monomer content were the similar specimens which presented with the highest flexural strength. Microwave postpolymerization irradiation can be an effective method for increasing the flexural strength of denture liner (at 650 W for 5 min) by reducing the residual monomer content by further polymerization at free radical sites.

  9. Effect of microwave postpolymerization treatment on residual monomer content and the flexural strength of autopolymerizing reline resin

    Directory of Open Access Journals (Sweden)

    Patil Padmakar

    2009-01-01

    Full Text Available Background : Microwave postpolymerization has been suggested as a method to improve the flexural strength of an autopolymerizing denture reline resin. However, the effect of microwave postpolymerization on the residual monomer content and its influence on flexural strength have not been investigated. Objectives : This study analyzed the effect of microwave postpolymerization on the residual monomer content and its influence on the flexural strength of an autopolymerizing reline resin (Denture Liner. Materials and Methods : A total of 70 specimens (64 Χ 10 Χ 3.3 mm were polymerized according to the manufacturer′s instructions and divided into 7 groups (n = 10. Control group specimens were not subjectedto any further processing. Before testing, the specimens were subjected to postpolymerization in a microwave oven using different power (550 and 650 W and time (3, 4, and 5 min settings. Two specimens of each group were then manually ground into fine powder and samples extracted from the specimens using reflux method. The samples were then subjected to gas chromatography for residual monomer determination in area%. Eight specimens were subjected to a three-point bending device with a span of 50 mm and crosshead speed of 5 mm/min, and the flexural strength was determined in MPa. Data analyses included Student′s t-test and one-way analysis of variance. Results : For the Denture Liner reline resin, the residual monomer content decreased and the flexural strength increased significantly with the application of microwave irradiation using different time/power combinations. The specimens with the lowest residual monomer content were the similar specimens which presented with the highest flexural strength. Conclusion : Microwave postpolymerization irradiation can be an effective method for increasing the flexural strength of denture liner (at 650 W for 5 min by reducing the residual monomer content by further polymerization at free radical sites.

  10. Treatment of biological waste and residues V. Biological - mechanical - thermal processes; Bio- und Restabfallbehandlung V. Biologisch - mechanisch - thermisch

    Energy Technology Data Exchange (ETDEWEB)

    Wiemer, K.; Kern, M. (eds.); Weber-Wied, R. (comp.)

    2001-07-01

    From 2005, the TA Siedlungsabfall (Waste Management Regulation) will come into force, and European legislation will overrule national legislation. Dumping of untreated waste in landfills will be prohibited, i.e. incinerators for thermal waste treatment must be constructed. In view of the rigid specifications for emissions and residues and the demand for Europe-wide invitations for tender, time is running short. The book outlines the options for action of the German states and of some applicant states for EC membership. The German government already issued an Ordinance for Power Generation from Biomass. Independent of this, also secondary fuels are gaining ground, and several contributions of the conference discussed quality assurance and utilization of secondary fuels. Composting and sewage sludge utilization are further current issues. Air pollution, soil and groundwater protection, job security and energy potential are gone into, and an outline of the current situation of waste management is attempted. [German] Die aktuelle abfallwirtschaftliche Situation wird in besonderem Masse gepraegt durch das nahende Jahr 2005 sowie die zunehmende Abhaengigkeit nationalstaatlicher Handlungsspielraeume von den Vorgaben europaeischer Rahmenrichtlinien. Hierbei wird der Handlungsdruck spuerbar, spaetestens ab dem Jahr 2005 der TA Siedlungsabfall Rechnung tragen zu muessen. Die verbleibenden Zeitraeume sind daher eng bemessen, beruecksichtigt man insbesondere die langen Genehmigungs- und Errichtungszeitraeume fuer thermische Behandlungsanlagen. Vor dem Hintergrund der europaweiten Ausschreibungspflicht wird die gegenwaertige technische Diskussion zur MBA sehr stark durch die nunmehr von der Bundesregierung konkretisierten Emissions- und Ablagerungsanforderungen gepraegt. Der vorliegende Band soll aufzeigen, welche Handlungsspielraeume sich hierbei aus Sicht der verschiedenen Bundeslaender ergeben. Ein Blick ueber die Grenzen hinaus zu einigen zukuenftigen EU

  11. THERMOSELECT. Continuous environment-friendly treatment of residues by gasification and direct melting; THERMOSELECT. Unterbrechungslose umweltgerechte Restabfallbehandlung durch Vergasung und Direkteinschmelzung

    Energy Technology Data Exchange (ETDEWEB)

    Gaeng, P.; Klein, K.; Stahlberg, R.; Weisenburger, P. [Thermoselect Suedwest GmbH, Karlsruhe (Germany)

    1996-12-31

    The Thermoselect process comprises waste compaction, degassing, gasification with pure oxygen, and melting of inorganic components in a continuous closed cycle process. The high-quality products can be recycled almost completely: The synthesis gas can be used as feedstock or combusted, also in high-efficiency power generation processes. The other products, e.g. the high-grade mineral and metal granulates, can be utilized without restrictions. The residual fraction which must be dumped is very small. (orig) [Deutsch] Mit Thermoselect ist eine neue Technik auf dem Markt, die durch die konsequente Umsetzung der Verfahrensschritte Abfallverdichtung, Entgasung, Vergasung mit reinem Sauerstoff und Einschmelzung der anorganischen Muellbestandteile in einem unterbrechungslosen geschlossenen Prozess hochwertige Produkte aus Abfaellen erzeugt, die nahezu vollstaendig verwertet werden koennen. Das erzeugte Synthesegas kann sowohl stofflich als auch thermisch genutzt werden, wobei der Einsatz von stromerzeugungsverfahren mit hohen Wirkungsgraden moeglich ist. Die ubrigen Produkte, z.B. das mineralische und das metallische Granulat, erreichen eine Qualitaet, die eine uneingeschraenkte Nutzung zulaesst. Die Anteile der z.Zt. noch zu entsorgenden Reststoffe ist gering, wobei derzeit meist wirtschafatliche Gruende deren Entsorgung nahelegen. (orig)

  12. Thermoplasticity and oxidative treatment of coal liquefaction residue obtained from NEDOL 1t/d PSU; NEDOL ho ekika zansa no netsuryudosei to sanka kaishitsu

    Energy Technology Data Exchange (ETDEWEB)

    Yamada, O. [National Institute for Resources and Environment, Tsukuba (Japan)

    1993-10-20

    This paper describes the following matters on the result of investigating liquefaction residues of two kinds of coals generated from a NEDOL liquefaction process, with respect to change in their thermoplasticity associated with oxidative treatment, using a Gieseler plastometer: The liquefaction residues show extremely high Gieseler fluidity before the oxidative treatment. However, the maximum fluidity and the flow temperature range decrease as a result of the oxidative treatment at 150{degree}C, and the fluidity disappears nearly completely in the oxidation of 400 hours or less. The maximum fluidity decreases with the progress of oxidation even under a pressurized condition (range of up to 40 kgf/cm{sup 2}), and this trend grows remarkable if the pressure is raised. Time-based change in the FT-IR spectra of the liquefaction residues associated with the oxidation was investigated by using an photoacoustic method and a diffusion reflection method. The result showed that such reactions have advanced as generation of oxygen containing groups including ketone and ester, and pull-out of aliphatic hydrogen. 16 refs., 9 figs., 1 tab.

  13. Interactions in recovery and in residual injury from sequential treatments of mouse haemopoietic and stromal marrow cell populations, using X-rays, cyclophosphamide and busulphan

    International Nuclear Information System (INIS)

    Qi, D.Y.; Hendry, J.H.; Testa, N.G.

    1991-01-01

    The acute recovery of day 11 CFU-S, iv-CFC and CFU-F in mouse bone marrow, following a test dose of X-rays, cyclophosphamide (CP) or busulphan given to mice previously treated with repeated priming dose X-rays or CP, was in general predictable from the amount of residual injury after the priming doses. A marked exception was iv-CFC after X-rays, which although amplified to near normal levels during the residual injury phase, recovered after the test irradiation from low-levels of CFU-S. The amount of residual injury after sequential treatments of different agents was in general less than expected on the basis of the product of the effects of the individual agents. This was most marked for CP priming treatments, where the long-term recovery of day 11 CFU-S after the test dose remained persistently above control levels. Also, some correlation was found between improved stromal recovery (CFU-F) and the CFU-S content following the sequential treatment protocols. (author). 33 refs.; 3 figs.; 5 tabs

  14. Combustion modeling in internal combustion engines

    Science.gov (United States)

    Zeleznik, F. J.

    1976-01-01

    The fundamental assumptions of the Blizard and Keck combustion model for internal combustion engines are examined and a generalization of that model is derived. The most significant feature of the model is that it permits the occurrence of unburned hydrocarbons in the thermodynamic-kinetic modeling of exhaust gases. The general formulas are evaluated in two specific cases that are likely to be significant in the applications of the model.

  15. Radiotracer studies of maneb residues in lettuce plants

    International Nuclear Information System (INIS)

    Sennaoui, Z.; Meguenni, H.; Bennaceur, M.

    1990-11-01

    Lettuce plants have received different treatments of 14C-maneb at variable time. A cleaning is made to determine the foliar surface residues. The analysis of CS2 showed relatively important amount especially for lots which have received 4 treatments (10,3ppm and 6,49ppm). The amounts found after combustion have showed increasing amounts, proportionally to the number of treatments. The analysis of ETU revealed a presence only for lots which have received several treatments (3 and 4). The analysis by TLC showed many metabolites. Two of them have been identified (ETU, EU). Interfoliar migration of 14C product occurred between treated leaves and untreated leaves of the same plant

  16. Char crystalline transformations during coal combustion and their implications for carbon burnout

    Energy Technology Data Exchange (ETDEWEB)

    Hurt, R.H.

    1999-07-07

    Residual, or unburned carbon in fly ash affects many aspects of power plant performance and economy including boiler efficiency, electrostatic precipitator operation, and ash as a salable byproduct. There is a large concern in industry on the unburned carbon problem due to a variety of factors, including low-NOx combustion system and internationalization of the coal market. In recent work, it has been found that residual carbon extracted from fly ash is much less reactive than the laboratory chars on which the current kinetics are based. It has been suggested that thermal deactivation at the peak temperature in combustion is a likely phenomenon and that the structural ordering is one key mechanism. The general phenomenon of carbon thermal annealing is well known, but there is a critical need for more data on the temperature and time scale of interest to combustion. In addition, high resolution transmission electron microscopy (HRTEM) fringe imaging, which provides a wealth of information on the nature and degree of crystallinity in carbon materials such as coal chars, has become available. Motivated by these new developments, this University Coal Research project has been initiated with the following goals: (1) To determine transient, high-temperature, thermal deactivation kinetics as a function of parent coal and temperature history. (2) To characterize the effect of the thermal treatment on carbon crystalline structure through high-resolution transmission electron microscopy and specialized, quantitative image analysis.

  17. Residuation theory

    CERN Document Server

    Blyth, T S; Sneddon, I N; Stark, M

    1972-01-01

    Residuation Theory aims to contribute to literature in the field of ordered algebraic structures, especially on the subject of residual mappings. The book is divided into three chapters. Chapter 1 focuses on ordered sets; directed sets; semilattices; lattices; and complete lattices. Chapter 2 tackles Baer rings; Baer semigroups; Foulis semigroups; residual mappings; the notion of involution; and Boolean algebras. Chapter 3 covers residuated groupoids and semigroups; group homomorphic and isotone homomorphic Boolean images of ordered semigroups; Dubreil-Jacotin and Brouwer semigroups; and loli

  18. A novel method to determine residual detergent in biological samples post endotoxin reduction treatment and evaluation of strategies for subsequent detergent removal.

    Science.gov (United States)

    London, Anne Serdakowski; Japutra, Chietara; Planck, Kyle; Lihon, Michael; Nguyen, Andrew Anh

    2016-08-01

    Endotoxin removal using detergent washes and extractions are well-established, efficient, and cost-effective methods; however, removing residual detergent post treatment has been shown to be a challenge. In this communication, we show a simple and fast method for determining the detergent concentration in a protein solution post treatment and highlight strategies for detergent removal to achieve levels below the critical micelle concentration (CMC), the minimum concentration at which detergent micelles form. Copyright © 2015 Elsevier B.V. All rights reserved.

  19. Life cycle assessment of post-consumer plastics production from waste electrical and electronic equipment (WEEE) treatment residues in a Central European plastics recycling plant

    International Nuclear Information System (INIS)

    Wäger, Patrick A.; Hischier, Roland

    2015-01-01

    Plastics play an increasingly important role in reaching the recovery and recycling rates defined in the European WEEE Directive. In a recent study we have determined the life cycle environmental impacts of post-consumer plastics production from mixed, plastics-rich WEEE treatment residues in the Central European plant of a market-leading plastics recycler, both from the perspective of the customers delivering the residues and the customers buying the obtained post-consumer recycled plastics. The results of our life cycle assessments, which were extensively tested with sensitivity analyses, show that from both perspectives plastics recycling is clearly superior to the alternatives considered in this study (i.e. municipal solid waste incineration (MSWI) and virgin plastics production). For the three ReCiPe endpoint damage categories, incineration in an MSWI plant results in an impact exceeding that of the examined plastics recycling facility each by about a factor of 4, and the production of virgin plastics has an impact exceeding that of the post-consumer recycled (PCR) plastics production each by a factor of 6–10. On a midpoint indicator level the picture is more differentiated, showing that the environmental impacts of the recycling options are lower by 50% and more for almost all impact factors. While this provides the necessary evidence for the environmental benefits of plastics recycling compared to existing alternatives, it can, however, not be taken as conclusive evidence. To be conclusive, future research will have to address the fate of hazardous substances in the outputs of such recycling systems in more detail. - Highlights: • LCA of plastics production from plastics-rich WEEE treatment residues • Multiple stakeholder perspectives addressed via different research questions • Plastics production from WEEE treatment residues clearly superior to alternatives • Robust results as demonstrated by extensive sensitivity analyses

  20. Life cycle assessment of post-consumer plastics production from waste electrical and electronic equipment (WEEE) treatment residues in a Central European plastics recycling plant

    Energy Technology Data Exchange (ETDEWEB)

    Wäger, Patrick A., E-mail: patrick.waeger@empa.ch; Hischier, Roland

    2015-10-01

    Plastics play an increasingly important role in reaching the recovery and recycling rates defined in the European WEEE Directive. In a recent study we have determined the life cycle environmental impacts of post-consumer plastics production from mixed, plastics-rich WEEE treatment residues in the Central European plant of a market-leading plastics recycler, both from the perspective of the customers delivering the residues and the customers buying the obtained post-consumer recycled plastics. The results of our life cycle assessments, which were extensively tested with sensitivity analyses, show that from both perspectives plastics recycling is clearly superior to the alternatives considered in this study (i.e. municipal solid waste incineration (MSWI) and virgin plastics production). For the three ReCiPe endpoint damage categories, incineration in an MSWI plant results in an impact exceeding that of the examined plastics recycling facility each by about a factor of 4, and the production of virgin plastics has an impact exceeding that of the post-consumer recycled (PCR) plastics production each by a factor of 6–10. On a midpoint indicator level the picture is more differentiated, showing that the environmental impacts of the recycling options are lower by 50% and more for almost all impact factors. While this provides the necessary evidence for the environmental benefits of plastics recycling compared to existing alternatives, it can, however, not be taken as conclusive evidence. To be conclusive, future research will have to address the fate of hazardous substances in the outputs of such recycling systems in more detail. - Highlights: • LCA of plastics production from plastics-rich WEEE treatment residues • Multiple stakeholder perspectives addressed via different research questions • Plastics production from WEEE treatment residues clearly superior to alternatives • Robust results as demonstrated by extensive sensitivity analyses.

  1. Lump wood combustion process

    Science.gov (United States)

    Kubesa, Petr; Horák, Jiří; Branc, Michal; Krpec, Kamil; Hopan, František; Koloničný, Jan; Ochodek, Tadeáš; Drastichová, Vendula; Martiník, Lubomír; Malcho, Milan

    2014-08-01

    The article deals with the combustion process for lump wood in low-power fireplaces (units to dozens of kW). Such a combustion process is cyclical in its nature, and what combustion facility users are most interested in is the frequency, at which fuel needs to be stoked to the fireplace. The paper defines the basic terms such as burnout curve and burning rate curve, which are closely related to the stocking frequency. The fuel burning rate is directly dependent on the immediate thermal power of the fireplace. This is also related to the temperature achieved in the fireplace, magnitude of flue gas losses and the ability to generate conditions favouring the full burnout of the fuel's combustible component, which, at once ensures the minimum production of combustible pollutants. Another part of the paper describes experiments conducted in traditional fireplaces with a grate, at which well-dried lump wood was combusted.

  2. Sclerosis and the Nd:YAG, Q-switched laser with multiple frequency for treatment of telangiectases, reticular veins, and residual pigmentation.

    Science.gov (United States)

    Cisneros, J L; Del Rio, R; Palou, J

    1998-10-01

    The combination of low concentrations of sclerosing solution and the Nd:YAG, Q-switched laser with multiple (quadruple) frequency provides good results in the treatment of telangiectases and reticular varicose veins of the lower extremities, as well as pigmentation that may appear during sclerotherapy. This paper is based on a series of patients with telangiectases and reticular veins who were treated with sclerotherapy and the Nd:YAG, Q-switched laser with quadruple frequency. Patients with telangiectases and reticular veins received two or three treatment sessions with polydocanol and the Nd:YAG, Q-switched laser with quadruple frequency. Then, they were assessed a clinical score corresponding to the level of improvement achieved. Residual hematic pigmentation lesions were also eliminated with the laser. Excellent improvement was evident in 90% of the patients with minimal residual lesions. The combined technique of sclerosing solution and the Nd:YAG laser with multiple frequency is a valid alternative for the elimination of telangiectases and reticular veins of the lower limbs. This technique has several advantages, such as the use of low concentrations of sclerosing solution, high patient acceptance levels due to minimal disturbances, and the fact that local anesthesia is unnecessary. Good results are obtained without complications and minimal residual pigmentation. These mild pigmentation can be treated with the Nd:YAG laser.

  3. Concept and operational results of a conversion to enhance the performance of steam generators for the combustion of refinery residues; Konzept und Betriebsergebnisse des Umbaus zur Leistungssteigerung der Dampferzeuger fuer die Verbrennung von Raffinerie-Rueckstaenden

    Energy Technology Data Exchange (ETDEWEB)

    Braecker, Roland [Balcke-Duerr GmbH, Ratingen (Germany); Thierbach, Hans-Ulrich [Steinmueller-Engineering GmbH, Gummersbach (Germany); Raehder, Uwe [PCK Raffinerie GmbH, Schwedt (Germany)

    2008-07-01

    Two natural circulation steam generators fired with refinery residual oils with a design capacity of 620 t/h, which had been commissioned at the end of the 90s, were upgraded at PCK Schwedt in order to increase their capacity to 750 t/h. Technical details of the upgrade, measures guaranteeing trouble-free operation and first operating results are presented. Experience clearly demonstrates that minor boiler fouling and high full-load availability of the boiler are achieved using HSC-R as fuel. (orig.)

  4. Combustion Byproducts Recycling Consortium

    Energy Technology Data Exchange (ETDEWEB)

    Paul Ziemkiewicz; Tamara Vandivort; Debra Pflughoeft-Hassett; Y. Paul Chugh; James Hower

    2008-08-31

    Ashlines: To promote and support the commercially viable and environmentally sound recycling of coal combustion byproducts for productive uses through scientific research, development, and field testing.

  5. Flameless Combustion Workshop

    National Research Council Canada - National Science Library

    Gutmark, Ephraim

    2005-01-01

    .... "Flameless Combustion" is characterized by high stability levels with virtually no thermoacoustic instabilities, very low lean stability limits and therefore extremely low NOx production, efficient...

  6. Research Combustion Laboratory (RCL)

    Data.gov (United States)

    Federal Laboratory Consortium — The Research Combustion Laboratory (RCL) develops aerospace propulsion technology by performing tests on propulsion components and materials. Altitudes up to 137,000...

  7. Improvement of the management of residual waste in areas without thermal treatment facilities: A life cycle analysis of an Italian management district.

    Science.gov (United States)

    Di Maria, Francesco; Micale, Caterina; Morettini, Emanuela; Sisani, Luciano; Damiano, Roberto

    2015-10-01

    Starting from an existing waste management district without thermal treatment facilities, two different management scenarios for residual waste were compared by life cycle assessment (LCA). The adoption of a bioreactor landfill for managing the mechanically sorted organic fraction instead of bio-stabilization led to reduction of global warming and fresh water eutrophication by 50% and 10%, respectively. Extraction of recyclables from residual waste led to avoided emissions for particulate matter, acidification and resource depletion impact categories. Marginal energy and the amount of energy recovered from landfill gas marginally affected the LCA results. On the contrary the quality of the recyclables extracted can significantly modify the eco profile of the management schemes. Copyright © 2015 Elsevier Ltd. All rights reserved.

  8. Iron storage in liver, bone marrow and splenic Gaucheroma reflects residual disease in type 1 Gaucher disease patients on treatment.

    Science.gov (United States)

    Regenboog, Martine; Bohte, Anneloes E; Akkerman, Erik M; Stoker, Jaap; Hollak, Carla E M

    2017-11-01

    Gaucher disease (GD) is a lysosomal storage disorder characterized by the storage of glycosphingolipids in macrophages. Despite effective therapy, residual disease is present in varying degrees and may be associated with late complications, such as persistent bone or liver disease and increased cancer risk. Gaucher macrophages are capable of storing iron and locations of residual disease may thus be detectable with iron imaging. Forty type 1 GD (GD1) patients and 40 matched healthy controls were examined using a whole-body magnetic resonance imaging protocol consisting of standard sequences, allowing analysis of iron content per organ, expressed as R2* (Hz). Median R2* values were significantly elevated in GD1 patients as compared to healthy controls in liver [41 Hz (range 29-165) vs. 38 Hz (range 28-53), P iron levels in liver and bone marrow, which may carry a risk for liver fibrosis and cancer. © 2017 John Wiley & Sons Ltd.

  9. Switching to aripiprazole for the treatment of residual mutism resulted in distinct clinical courses in two catatonic schizophrenia cases

    OpenAIRE

    Muneoka, Katsumasa; Kanahara, Nobuhisa; Kimura, Shou

    2017-01-01

    Objectives: The efficacy of a partial agonist for the dopamine D2 receptor, aripiprazole, for catatonia in schizophrenia has been reported. Methods: We report distinct clinical courses in challenging aripiprazole to treat residual mutism after severe catatonic symptoms improved. Results: In the first case, mutism was successfully treated when the patient was switched from olanzapine to aripiprazole. In contract, switching to aripiprazole from risperidone aggravated auditory hallucinations in ...

  10. Residual Mosquito Barrier Treatments on U.S. Military Camouflage Netting in a Southern California Desert Environment

    Science.gov (United States)

    2010-08-01

    8217- ’̂ pioneering work with other treated artificial substrates such as suspended or spread sheets,’’’"’ livestock fencing,’"" attractant -baited...more attractive to tnosquitoes, or situated in a zone with greater densities of mosquitoes. Mosquito reductions in treated enclosures and the treated...Permethrin as a residual lawn spray for adult mosquito control. Mosq News 1983; 43: 164-9. 7. Robert LL, Perich MJ: Phlebotomine sand fly ( Diptera

  11. Combustion mode switching with a turbocharged/supercharged engine

    Science.gov (United States)

    Mond, Alan; Jiang, Li

    2015-09-22

    A method for switching between low- and high-dilution combustion modes in an internal combustion engine having an intake passage with an exhaust-driven turbocharger, a crankshaft-driven positive displacement supercharger downstream of the turbocharger and having variable boost controllable with a supercharger bypass valve, and a throttle valve downstream of the supercharger. The current combustion mode and mass air flow are determined. A switch to the target combustion mode is commanded when an operating condition falls within a range of predetermined operating conditions. A target mass air flow to achieve a target air-fuel ratio corresponding to the current operating condition and the target combustion mode is determined. The degree of opening of the supercharger bypass valve and the throttle valve are controlled to achieve the target mass air flow. The amount of residual exhaust gas is manipulated.

  12. Gender differences in quality of life and functional disability for depression outpatients with or without residual symptoms after acute phase treatment in China.

    Science.gov (United States)

    Zhao, Na; Wang, Xiaohong; Wu, Wenyuan; Hu, Yongdong; Niu, Yajuan; Wang, Xueyi; Gao, Chengge; Zhang, Ning; Fang, Yiru; Huang, Jizhong; Liu, Tiebang; Jia, Fujun; Zhu, Xuequan; Hu, Jian; Wang, Gang

    2017-09-01

    Depression is associated with substantial personal suffering and reduced quality of life and functioning. The aim of this study was to investigate gender differences on quality of life and functional impairment of outpatients with depression after acute phase treatment. 1503 depression outpatients were recruited from eleven hospitals in China. Subjects were evaluated with sociodemographic characteristics, history and self-report instruments, related to severity of symptoms, function and quality of life. All data were analyzed to determine the gender differences. Men had a younger age at onset and the first onset age, higher education compared to women in total patients and with or without residual symptoms group. Using regression analysis, it was found that gender was significantly statistically related to severity scores of SDS and had no correlation with Q-LES-Q-SF total scores. In the residual symptoms group, greater functional impairment was noted by men in the area of work and social life. Significant gender differences of mood, work and sexual life in quality of life were observed. This is a cross-sectional study of depressed outpatients and duration of acute phase treatment may not an adequate time to measure changes. Depression appears to affect men more seriously than women after acute phase treatment. Men had a younger age at onset and the first onset age, higher education, more functional impairment and lower satisfaction of quality of life in mood, work and sexual life. Gender differences affect acute treatment, remission and recovery. Copyright © 2017 Elsevier B.V. All rights reserved.

  13. Suitability of steam exploded residual softwood for the production of binderless panels. Effect of the pre-treatment severity and lignin addition

    Energy Technology Data Exchange (ETDEWEB)

    Angles, M.N.; Ferrando, F.; Farriol, X.; Salvado, J. [Universitat Rovira i Virgili, Tarragona (Spain). Escola Tecnica Superior d' Enginyeria

    2001-07-01

    A steam explosion pre-treatment was applied at various severities to softwood residual substrate to determine the most suitable pre-treatment for the manufacture of binderless panels. The effect of adding acid to the pre-treatment of fibres was also evaluated. The changes in the chemical composition and morphology of the original material were investigated by fractionation analyses and scanning electron micrographs. High severities caused defibrillation of the material allowing to build links to form the panels. Prehydrolysis with acid had a great effect of the structure of the material even at low acid concentration, The physical and mechanical properties of the panel improved with as the severity of the pre-treatment increased up to a point where mechanical properties deteriorated. The composites with highest internal bond had a high cellulose content and a medium lignin content, All these factors suggested that steamed pre-treated residual could be improved by adding a natural binder to produce the panels. A test of producing panels with addition of several kinds of lignin (up to 20%) was performed. With no significant changes in density, water stability (thickness swelling and water absorption) internal bond and mechanical properties were greatly improved., Results after accelerated ageing test were also enhanced. (Author)

  14. Dioxines, furans and other pollutants emissions bond to the combustion of natural and additive woods; Facteurs d'emission. Emissions de dioxines, de furanes et d'autres polluants liees a la combustion de bois naturels et adjuvantes

    Energy Technology Data Exchange (ETDEWEB)

    Collet, S

    2000-02-15

    This report deals especially on the dioxines and furans bond to the combustion of wood in industrial furnaces and domestic furnaces. It aims to define the environmental strategy which would allow the combustion of wood residues to produce energy. The first part recalls general aspects concerning the wood. The six other parts presents the wood resources and wastes, the additive used, the combustion and the different factors of combustion and finally the pollutants emissions. (A.L.B.)

  15. Combustion of poultry litter in a fluidised bed combustor

    Energy Technology Data Exchange (ETDEWEB)

    P. Abelha; I. Gulyurtlu; D. Boavida; J. Seabra Barros; I. Cabrita; J. Leahy; B. Kelleher; M. Leahy [DEECA-INETI, Lisbon (Portugal)

    2003-04-01

    Combustion studies of poultry litter alone or mixed with peat by 50% on weight basis were undertaken in an atmospheric bubbling fluidised bed. Because of high moisture content of poultry litter, there was some uncertainty whether the combustion could be sustained on 100% poultry litter and as peat is very available in Ireland, its presence was considered to help to improve the combustion. However, the results showed that, as long as the moisture content of poultry litter was kept below 25%, the combustion did not need the addition of peat. The main parameters that were investigated are (i) moisture content, (ii) air staging, and (iii) variations in excess air levels along the freeboard. The main conclusions of the results are (i) combustion was influenced very much by the conditions of the fuel supply, (ii) the steady fuel supply was strongly dependent on the moisture content of the poultry litter, (iii) temperature appeared to be still very influential in reducing the levels of unburned carbon and hydrocarbons released from residues, (iv) the air staging in the freeboard improved combustion efficiency by enhancing the combustion of volatiles released from residues in the riser and (vi) NOx emissions were influenced by air staging in the freeboard. Particles collected from the bed and the two cyclones were analysed to determine the levels of heavy metals and the leachability tests were carried out with ashes collected to verify whether or not they could safely be used in agricultural lands. 8 refs., 1 fig., 8 tabs.

  16. Chemical speciation, mobility and phyto-accessibility of heavy metals in fly ash and slag from combustion of pelletized municipal sewage sludge.

    Science.gov (United States)

    Xiao, Zhihua; Yuan, Xingzhong; Li, Hui; Jiang, Longbo; Leng, Lijian; Chen, Xiaohong; Zeng, Guangming; Li, Fei; Cao, Liang

    2015-12-01

    Combustion of pelletized municipal sewage sludge (MSS) can generate pestilent byproducts: fly ash and slag. Comparisons of heavy metal sequential extraction results among MSS, fly ash and slag showed that after combustion, the bioavailable heavy metal fractions (acid soluble/exchangeable, reducible and oxidizable fractions) were mostly transformed into the very stable heavy metal fractions (residual fractions). On the other hand, the results of toxicity characteristic leaching procedure (TCLP), diethylenetriamine pentaacetic acid and HCl extraction (phyto-accessibility assessment) demonstrated that the mobility and toxicity of heavy metals were greatly reduced. The direct and long-term bioavailability and eco-toxicity of heavy metals in fly ash and slag were relieved, which implied that combustion of pelletized MSS could be a promising and completely safe disposal technology for MSS treatment. Copyright © 2015 Elsevier B.V. All rights reserved.

  17. Strobes: An oscillatory combustion

    NARCIS (Netherlands)

    Corbel, J.M.L.; Lingen, J.N.J. van; Zevenbergen, J.F.; Gijzeman, O.L.J.; Meijerink, A.

    2012-01-01

    Strobe compositions belong to the class of solid combustions. They are mixtures of powdered ingredients. When ignited, the combustion front evolves in an oscillatory fashion, and flashes of light are produced by intermittence. They have fascinated many scientists since their discovery at the

  18. Catalytically enhanced combustion process

    International Nuclear Information System (INIS)

    Rodriguez, C.

    1992-01-01

    This patent describes a fuel having improved combustion efficiency. It comprises a petroleum based liquid hydrocarbon; and a combustion catalyst comprising from about 18 to about 21 weight percent naphthalene, from about 75 to about 80 weight percent toluene, and from about 2.8 to about 3.2 weight percent benzyl alcohol

  19. Strobes: An Oscillatory Combustion

    NARCIS (Netherlands)

    Corbel, J.M.L.; van Lingen, J.N.J.; Zevenbergen, J.F.; Gijzeman, O.L.J.; Meijerink, A.

    2012-01-01

    Strobe compositions belong to the class of solid combustions. They are mixtures of powdered ingredients. When ignited, the combustion front evolves in an oscillatory fashion, and flashes of light are produced by intermittence. They have fascinated many scientists since their discovery at the

  20. Fifteenth combustion research conference

    International Nuclear Information System (INIS)

    1993-01-01

    The BES research efforts cover chemical reaction theory, experimental dynamics and spectroscopy, thermodynamics of combustion intermediates, chemical kinetics, reaction mechanisms, combustion diagnostics, and fluid dynamics and chemically reacting flows. 98 papers and abstracts are included. Separate abstracts were prepared for the papers

  1. Fifteenth combustion research conference

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1993-06-01

    The BES research efforts cover chemical reaction theory, experimental dynamics and spectroscopy, thermodynamics of combustion intermediates, chemical kinetics, reaction mechanisms, combustion diagnostics, and fluid dynamics and chemically reacting flows. 98 papers and abstracts are included. Separate abstracts were prepared for the papers.

  2. The Heat of Combustion of Tobacco and Carbon Oxide Formation

    Directory of Open Access Journals (Sweden)

    Norman AB

    2014-12-01

    Full Text Available Recent studies demonstrated a relationship between mass burn rates of straight-grade cigarettes and heats of combustion of the tobacco materials. In the present work, relationships between measured heats of combustion and elemental composition of the tobacco materials were further analyzed. Heats of combustion measured in oxygen were directly correlated with the carbon and hydrogen content of the tobacco materials tested. Ash content of the materials was inversely related to the heats of combustion. The water insoluble residues from exhaustively extracted tobacco materials showed higher heats of combustion and higher carbon content than the non-extracted materials, confirming a direct relationship between carbon content and heat of combustion. A value for the heat of formation of tobacco was estimated (1175 cal/g from the heat of combustion data and elemental analysis results. The estimated value for heat of formation of tobacco appears to be constant regardless of the material type. Heat values measured in air were uniformly lower than the combustion heats in oxygen, suggesting formation of CO and other reaction products. Gases produced during bomb calorimetry experiments with five tobacco materials were analyzed for CO and CO2 content. When the materials were burned in oxygen, no CO was found in the gases produced. Measured heats of combustion matched estimates based on CO2 found in the gas and conversion of the sample hydrogen content to water. Materials burned in air produced CO2 (56% to 77% of the sample carbon content and appreciable amounts of CO (7% to 16% of the sample carbon content. Unburned residue containing carbon and hydrogen was found in the air combustion experiments. Estimated heat values based on amounts of CO and CO2 found in the gas and water formed from the hydrogen lost during combustion in air were higher than the measured values. These observations indicate formation of products containing hydrogen when the materials

  3. Identification of fuel effluents in waste water. Its influence in depuration process by active sludges. Identificacion de vertidos combustibles en agua residual. Su influencia en el proceso de depuracion por fongos activos

    Energy Technology Data Exchange (ETDEWEB)

    Parody, F.; Rebollo, M.C.; Azcarate, J.; Sammillan, I.; Beltran, V.M. (Ayuntamiento de Madrid (Spain))

    1994-01-01

    Frequently, fuel effluents are found in treatment water plants. This effluents are nocives for the biologic process. In this work the authors present an easy method for characterizing the fuel wastes in waste water and its chromatografic characterization in the water treatment plant in Madrid (Spain).

  4. Fuels and Combustion

    KAUST Repository

    Johansson, Bengt

    2016-08-17

    This chapter discusses the combustion processes and the link to the fuel properties that are suitable for them. It describes the basic three concepts, including spark ignition (SI) and compression ignition (CI), and homogeneous charge compression ignition (HCCI). The fuel used in a CI engine is vastly different from that in an SI engine. In an SI engine, the fuel should sustain high pressure and temperature without autoignition. Apart from the dominating SI and CI engines, it is also possible to operate with a type of combustion: autoignition. With HCCI, the fuel and air are fully premixed before combustion as in the SI engine, but combustion is started by the increased pressure and temperature during the compression stroke. Apart from the three combustion processes, there are also a few combined or intermediate concepts, such as Spark-Assisted Compression Ignition (SACI). Those concepts are discussed in terms of the requirements of fuel properties.

  5. PDF Modeling of Turbulent Combustion

    National Research Council Canada - National Science Library

    Pope, Stephen B

    2006-01-01

    .... The PDF approach to turbulent combustion has the advantages of fully representing the turbulent fluctuations of species and temperature, and of allowing realistic combustion chemistry to be implemented...

  6. Evaluation of a treatment system type septic tank - filter anaerobic of upward flow for the residual waters of the ecological benefit of the coffee

    International Nuclear Information System (INIS)

    Sanchez C, Jose Alejandro

    1997-01-01

    Colombia is the first country in the production of soft coffee in the world. The benefit for humid way it makes that this quality of coffee is obtained; however, the high consumption of water in the process and the later discharge to the superficial or underground sources, they have generated an environmental problem of great magnitude. Also, the sources of water that they have been contaminated with the discharges of the liquid waste that come from benefit of coffee they present, among other, serious inconveniences to be used as supplying sources of drinkable water. In time of crop, the coffee areas and their superficial sources of water usually register high indexes of contamination like consequence of the discharges of residual waters that come from the benefit of the coffee. In the Departments of Quindio, Valle, Caldas, Antioquia, etc., they have been come executing investigations of the residuals treatment that are derived of the pulp removal of the coffee (via humid), for anaerobic methods with satisfactory results. This project had the collaboration of the Departmental Committee of Coffee of Antioquia and the Environmental Engineering of the Antioquia University and it is formulated toward the evaluation of a Anaerobic filter of Ascendant flow, FAFA, preceded of a septic tank (biological sedimentation), as a treatment system of the coffee residual waters, with a waste native of a ecological benefit area. The obtained results were satisfactory although the generated waste is very intermittent and in times that are not of coffee crop it doesn't take place; what hinders more the application of biological systems for its treatment

  7. Phosphorus Sorption Capacity of Concrete Waste, Natural Sorbents, Alum Residuals from Water Supply Sludge, and Ceramic Material for Tertiary Treatment in Onsite Systems

    Directory of Open Access Journals (Sweden)

    Siriporn Larpkiattaworn

    2013-01-01

    Full Text Available The phosphorus (P sorption capacity was determined for concrete waste, alum residuals from water treatment sludge, and natural sorbents (shells, clay, kaolin, and mordenite from various parts of Thailand. The material showing the best P sorption capacity (shells was selected for preparing a ceramic material to support the growth of nitrifying bacteria. The ceramic material, consisting of shells (50% by weight, alum residuals sludge (40% by weight and a soil (10% by weight heat at 750°C for about one hour, was studied for its P sorption capacity. Langmuir and Freundlich sorption isotherms yielded similar relative maximum P sorption capacities for the sorbents. The results from the Langmuir calculations showed the following maximum P sorption capacities: 32.26 g P/Kg shells, 31.25 g P/Kg concrete waste, 7.19 g P/Kg alum residuals sludge, 290 mg P/Kg clay, 80 mg P/Kg kaolin, and 30 mg P/Kg mordenite. The P sorption capacity for the prepared ceramic material at grain size 12 mm was 4.85 g P/kg. This result suggests that the ceramic material could be used for P sorption while providing growth support for nitrifying bacteria, similar to the well documented a popular P sorption material: light expanded clay aggregate (LECA from Sweden.

  8. An evaluation of the residual toxicity and chemistry of a sodium hydroxide-based ballast water treatment system for freshwater ships

    Science.gov (United States)

    Elskus, Adria; Ingersoll, Christopher G.; Kemble, Nile E.; Echols, Kathy R.; Brumbaugh, William G.; Henquinet, Jeffrey; Watten, Barnaby J.

    2015-01-01

    Nonnative organisms in the ballast water of freshwater ships must be killed to prevent the spread of invasive species. The ideal ballast water treatment system (BWTS) would kill 100% of ballast water organisms with minimal residual toxicity to organisms in receiving waters. In the present study, the residual toxicity and chemistry of a BWTS was evaluated. Sodium hydroxide was added to elevate pH to >11.5 to kill ballast water organisms, then reduced to pH water under an air atmosphere (pH drifted to ≥9) or a 2.5% CO2 atmosphere (pH 7.5–8.2), then transferred to control water for 5 d to assess potential delayed toxicity. Chemical concentrations in the BWTS water met vessel discharge guidelines with the exception of concentrations of copper. There was little to no residual toxicity to cladocerans or fish, but the BWTS water was toxic to amphipods. Maintaining a neutral pH and diluting BWTS water by 50% eliminated toxicity to the amphipods. The toxicity of BWTS water would likely be minimal because of rapid dilution in the receiving water, with subsurface release likely preventing pH rise. This BWTS has the potential to become a viable method for treating ballast water released into freshwater systems.

  9. An evaluation of the residual toxicity and chemistry of a sodium hydroxide-based ballast water treatment system for freshwater ships.

    Science.gov (United States)

    Elskus, Adria A; Ingersoll, Christopher G; Kemble, Nile E; Echols, Kathy R; Brumbaugh, William G; Henquinet, Jeffrey W; Watten, Barnaby J

    2015-06-01

    Nonnative organisms in the ballast water of freshwater ships must be killed to prevent the spread of invasive species. The ideal ballast water treatment system (BWTS) would kill 100% of ballast water organisms with minimal residual toxicity to organisms in receiving waters. In the present study, the residual toxicity and chemistry of a BWTS was evaluated. Sodium hydroxide was added to elevate pH to >11.5 to kill ballast water organisms, then reduced to pH pH drifted to ≥9) or a 2.5% CO2 atmosphere (pH 7.5-8.2), then transferred to control water for 5 d to assess potential delayed toxicity. Chemical concentrations in the BWTS water met vessel discharge guidelines with the exception of concentrations of copper. There was little to no residual toxicity to cladocerans or fish, but the BWTS water was toxic to amphipods. Maintaining a neutral pH and diluting BWTS water by 50% eliminated toxicity to the amphipods. The toxicity of BWTS water would likely be minimal because of rapid dilution in the receiving water, with subsurface release likely preventing pH rise. This BWTS has the potential to become a viable method for treating ballast water released into freshwater systems. © 2015 SETAC.

  10. X-ray absorption spectroscopy as a tool investigating arsenic(III) and arsenic(V) sorption by an aluminum-based drinking-water treatment residual.

    Science.gov (United States)

    Makris, Konstantinos C; Sarkar, Dibyendu; Parsons, Jason G; Datta, Rupali; Gardea-Torresdey, Jorge L

    2009-11-15

    Historic applications of arsenical pesticides to agricultural land have resulted in accumulation of residual arsenic (As) in such soils. In situ immobilization represents a cost-effective and least ecological disrupting treatment technology for soil As. Earlier work in our laboratory showed that drinking-water treatment residuals (WTRs), a low-cost, waste by-product of the drinking-water treatment process exhibit a high affinity for As. Wet chemical experiments (sorption kinetics and desorption) were coupled with X-ray absorption spectroscopy measurements to elucidate the bonding strength and type of As(V) and As(III) sorption by an aluminum-based WTR. A fast (1h), followed by a slower sorption stage resulted in As(V) and As(III) sorption capacities of 96% and 77%, respectively. Arsenic desorption with a 5mM oxalate from the WTR was minimal, being always absorption spectroscopy data showed inner-sphere complexation between As and surface hydroxyls. Reaction time (up to 48h) had no effect on the initial As oxidation state for sorbed As(V) and As(III). A combination of inner-sphere bonding types occurred between As and Al on the WTR surface because mixed surface geometries and interatomic distances were observed.

  11. Effect of shot peening treatment in the behavior of residual stress in duplex stainless steel during medium cycle fatigue; Efeito do tratamento de shot peening no comportamento das tensoes residuais em aco inoxidavel duplex durante fadiga de medio ciclo

    Energy Technology Data Exchange (ETDEWEB)

    Pedrosa, Peter D.S.; Rebello, Joao Marcos A. [Coordenacao dos Programas de Pos-Graduacao de Engenharia (PEMM/COPPE/UFRJ), Rio de Janeiro, RJ (Brazil). Programa de Engenharia Metalurgica e de Materiais; Fonseca, Maria P. Cindra, E-mail: mcindra@vm.uff.b [Universidade Federal Fluminense (PGMEC/UFF), Niteroi, RJ (Brazil). Escola de Engenharia. Programa de Pos-Graduacao em Engenharia Mecanica

    2010-07-01

    The lifetime of duplex stainless steel parts experiencing cyclic fatigue is directly influenced by the residual stresses present in the ferrite and austenite phases. The motivation for this work was to analyze the behaviour of the residual stresses fields introduced by shot peening treatment in both phases, in the sample surface as in the subsurface layers, in low fatigue cycles, using the X-rays diffraction technique. The results shows that the compressive residual stresses introduced by the shot peening treatment in both phases improved fatigue life of the material. However, the cyclical loads produce partial or total relief in these residual stresses fields. It was verified that the shot peening process induced the formation of microcracks only in the ferrite phase. The largest variations in the total compressive residual stresses fields also occurred in this phase. The samples surfaces were analyzed by scanning electron microscopy. (author)

  12. Residue processing

    Energy Technology Data Exchange (ETDEWEB)

    Gieg, W.; Rank, V.

    1942-10-15

    In the first stage of coal hydrogenation, the liquid phase, light and heavy oils were produced; the latter containing the nonliquefied parts of the coal, the coal ash, and the catalyst substances. It was the problem of residue processing to extract from these so-called let-down oils that which could be used as pasting oils for the coal. The object was to obtain a maximum oil extraction and a complete removal of the solids, because of the latter were returned to the process they would needlessly burden the reaction space. Separation of solids in residue processing could be accomplished by filtration, centrifugation, extraction, distillation, or low-temperature carbonization (L.T.C.). Filtration or centrifugation was most suitable since a maximum oil yield could be expected from it, since only a small portion of the let-down oil contained in the filtration or centrifugation residue had to be thermally treated. The most satisfactory centrifuge at this time was the Laval, which delivered liquid centrifuge residue and centrifuge oil continuously. By comparison, the semi-continuous centrifuges delivered plastic residues which were difficult to handle. Various apparatus such as the spiral screw kiln and the ball kiln were used for low-temperature carbonization of centrifuge residues. Both were based on the idea of carbonization in thin layers. Efforts were also being made to produce electrode carbon and briquette binder as by-products of the liquid coal phase.

  13. Measurements of functional residual capacity during intensive care treatment: the technical aspects and its possible clinical applications.

    Science.gov (United States)

    Heinze, H; Eichler, W

    2009-10-01

    Direct measurement of lung volume, i.e. functional residual capacity (FRC) has been recommended for monitoring during mechanical ventilation. Mostly due to technical reasons, FRC measurements have not become a routine monitoring tool, but promising techniques have been presented. We performed a literature search of studies with the key words 'functional residual capacity' or 'end expiratory lung volume' and summarize the physiology and patho-physiology of FRC measurements in ventilated patients, describe the existing techniques for bedside measurement, and provide an overview of the clinical questions that can be addressed using an FRC assessment. The wash-in or wash-out of a tracer gas in a multiple breath maneuver seems to be best applicable at bedside, and promising techniques for nitrogen or oxygen wash-in/wash-out with reasonable accuracy and repeatability have been presented. Studies in ventilated patients demonstrate that FRC can easily be measured at bedside during various clinical settings, including positive end-expiratory pressure optimization, endotracheal suctioning, prone position, and the weaning from mechanical ventilation. Alveolar derecruitment can easily be monitored and improvements of FRC without changes of the ventilatory setting could indicate alveolar recruitment. FRC seems to be insensitive to over-inflation of already inflated alveoli. Growing evidence suggests that FRC measurements, in combination with other parameters such as arterial oxygenation and respiratory compliance, could provide important information on the pulmonary situation in critically ill patients. Further studies are needed to define the exact role of FRC in monitoring and perhaps guiding mechanical ventilation.

  14. ANALYSIS OF INTERNAL COMBUSTION ENGINE WITH A NEW CONCEPT OF POROUS MEDIUM COMBUSTION FOR THE FUTURE CLEAN ENGINE

    Directory of Open Access Journals (Sweden)

    Ashok A Dhale

    2010-01-01

    Full Text Available At present, the emissions of internal combustion engine can only be improved by catalytic treatments of the exhaust gases. Such treatments, however, result in high costs and relatively low conversion efficiency. This suggests that a new combustion technique should be developed to yield improved primary combustion processes inside the engine with drastically reduced exhaust gas emissions. To fulfill all requirements, Dr. Franz Drust has proposed a new combustion concept to perform homogenous combustion in internal combustion engines. This concept used the porous medium combustion technique and is called "PM-engine". It is shown that the PM combustion technique can be applied to internal combustion engines. Theoretical considerations are presented for internal combustion engines, indicating that an overall improvement in thermal efficiency can be achieved for the PM-engine. This is explained and general performance of the new PM-engines is demonstrated for a single cylinder, water cooled, direct injection diesel engine. Verification of experiments at primary stage is described that were carried out as a part of the present study.

  15. Research on Toxicity Evaluation of Waste Incineration Residues of Printed Circuit Boards

    Directory of Open Access Journals (Sweden)

    Rasa Volungevičienė

    2014-10-01

    Full Text Available Recycling waste printed circuit boards (PCB is an extremely complicated process, because PCBs consist of a number of complex components – hazardous and non-hazardous materials sets. Pyrolysis and combustion are currently the most effective treatment technologies for waste printed circuit boards. Pyrolysis can be used for thermally decomposing PCBs allowing for the simultaneous recovery of valuable materials. Following the extraction of valuable materials, the problem of residual ash utilization is encountered. Determining the qualitative and quantitative characteristics of incineration residue helps with choosing effective ash management technologies. This paper analyzes PCB ash generated at three different temperatures of 400 °C, 500 °C and 600 °C. Ash residues have been analysed to determine the quantity and type of metals present. Furthermore, the experiment of leaching heavy metals from ash has been described.

  16. Influence of treatment by vibration in residual stress generated in the laser welding of HSLA and IF steels; Influencia do tratamento de vibracao nas tensoes residuais geradas na soldagem a laser de acos ARBL e IF

    Energy Technology Data Exchange (ETDEWEB)

    Chuvas, T.C.; Fonseca, M.P. Cindra, E-mail: chuvas@vm.uff.b [Universidade Federal Fluminense (PGMEC/UFF), Niteroi, RJ (Brazil). Programa de Pos-graduacao em Engenharia Mecanica; Castello, D.A. [Universidade Federal do Rio de Janeiro (DEM/UFRJ), RJ (Brazil). Dept. de Engenharia Mecanica

    2010-07-01

    The stress relieving treatment by vibration is a new technology under development, which has many advantages over thermal methods. In this work was analyzed the surface residual stress generated in the laser welding of biphasic HSLA and IF steels, both used in the automotive industry. Residual stresses were measured by X-ray diffraction, by the sen{sup 2} {Psi} method. Residual stresses generated in the welding of the samples were tensile at all points measured. After welding, the samples were submitted to the mechanical vibration treatment. Some samples presented a significant reduction in the stress values. The welded joints were also characterized by optical microscopy. (author)

  17. Combustion en lit fluidisé Fluidized-Bed Combustion

    Directory of Open Access Journals (Sweden)

    Chrysostome G.

    2006-11-01

    Full Text Available Après quelques rappels généraux sur la fluidisation où seront présentés en par-ticulier les avantages qu'elle offre en combustion, on exposera l'état actuel du développement des générateurs à lit fluidisé opérant avec les combustibles suivants : charbon, combustibles pétroliers, résidus divers ; il sera fait mention de la contribution de l'Institut Français du Pétrole (IFP dans les deux derniers domaines.On présentera ensuite les installations les plus récentes en traitement de minerais (grillage des sulfures, calcination de calcaires. En raison de son importance on examinera encore les possibilités de désulfuration au sein de lits fluidisés, de même que seront commentés les travaux de régénération des absorbants.On terminera enfin en mentionnant les développements des lits circulants ou rapides, considérés comme les réacteurs de la seconde génération. After a general review of fluidization including in particular the advantages it offers for combustion, this article describes the present state of the development of fluidized-bed gcnerators operating with the following fuels : cool, petroleum fuels, different residues. Mention is made of Institut Français du Pétrole (IFP contribution in the last two fields. Then the most recent ore-treating installations are described (roasting of sulfides, calcination of limestones. Because of its importance, the possibilities of desulfurizoticn inside fluidized beds is examined, and research on the regeneration of absorbants is commented on. The article ends by mentioning the development of circulating or fast beds which are considered as second generation reactors.

  18. Trace gas emissions from combustion of peat, crop residue, domestic biofuels, grasses, and other fuels: configuration and Fourier transform infrared (FTIR) component of the fourth Fire Lab at Missoula Experiment (FLAME-4)

    Science.gov (United States)

    Stockwell, C. E.; Yokelson, R. J.; Kreidenweis, S. M.; Robinson, A. L.; DeMott, P. J.; Sullivan, R. C.; Reardon, J.; Ryan, K. C.; Griffith, D. W. T.; Stevens, L.

    2014-09-01

    During the fourth Fire Lab at Missoula Experiment (FLAME-4, October-November 2012) a large variety of regionally and globally significant biomass fuels was burned at the US Forest Service Fire Sciences Laboratory in Missoula, Montana. The particle emissions were characterized by an extensive suite of instrumentation that measured aerosol chemistry, size distribution, optical properties, and cloud-nucleating properties. The trace gas measurements included high-resolution mass spectrometry, one- and two-dimensional gas chromatography, and open-path Fourier transform infrared (OP-FTIR) spectroscopy. This paper summarizes the overall experimental design for FLAME-4 - including the fuel properties, the nature of the burn simulations, and the instrumentation employed - and then focuses on the OP-FTIR results. The OP-FTIR was used to measure the initial emissions of 20 trace gases: CO2, CO, CH4, C2H2, C2H4, C3H6, HCHO, HCOOH, CH3OH, CH3COOH, glycolaldehyde, furan, H2O, NO, NO2, HONO, NH3, HCN, HCl, and SO2. These species include most of the major trace gases emitted by biomass burning, and for several of these compounds, this is the first time their emissions are reported for important fuel types. The main fire types included African grasses, Asian rice straw, cooking fires (open (three-stone), rocket, and gasifier stoves), Indonesian and extratropical peat, temperate and boreal coniferous canopy fuels, US crop residue, shredded tires, and trash. Comparisons of the OP-FTIR emission factors (EFs) and emission ratios (ERs) to field measurements of biomass burning verify that the large body of FLAME-4 results can be used to enhance the understanding of global biomass burning and its representation in atmospheric chemistry models. Crop residue fires are widespread globally and account for the most burned area in the US, but their emissions were previously poorly characterized. Extensive results are presented for burning rice and wheat straw: two major global crop residues

  19. Oil use of the effluent plant ETEO (Effluent Station of Oil Treatment) as combustible for generation of energy in the power plant UG-50Hz; Utulizacao de oleo da ETEO (Estacao de Tratamento de Efluentes Oleosos) para geracao de energia na UG-50Hz

    Energy Technology Data Exchange (ETDEWEB)

    Souza, Jose Francisco de; Nascimento, Jose Maria do; Silva, Luiz Antonio da; Salazar, Marcos Vinicios; Baptista, Reinaldo Lopes; Barros, Sueli Aguiar [Companhia Siderurgica Nacional (CSN), Volta Redonda, RJ (Brazil)

    2009-11-01

    The areas of finishing products of CSN Steel Plant generate contaminated effluents with oil and grease , that are treated in ETEO (Effluent Station of Oil Treatment). In this plant, the oil is processed to be sold for the consuming market. However, some seasons of the year, the market does not absorb the oil, and CSN is obliged to defray the burning of this oil, to not interrupt the productive process and cause an environmental impact. Because of this situation, we search alternatives for the viable use of this oil inside CSN steel plant, taking care for the security of the processes and the impact to the environment. This paper describes the details of the work and the implantation of the burning of this oil of the ETEO with BPF oil (type of petrochemical oil) as combustible in the boiler 7 of the power plant UG 50 Hz. For the implantation of this project, operational contingencies of security for equipment was prepared . Moreover, the work included chemical analyses of the oil and the conditions of the boiler using this mixing of oils. The reached results demonstrate the total viability of this project and it was proved another alternative of the use of this residue, with reduction of the fuel costs , steam costs and the electric energy generated in the power plant of CSN. (author)

  20. Evaluation of Membrane Ultrafiltration and Residual Chlorination as a Decentralized Water Treatment Strategy for Ten Rural Healthcare Facilities in Rwanda

    OpenAIRE

    Alexandra Huttinger; Robert Dreibelbis; Kristin Roha; Fidel Ngabo; Felix Kayigamba; Leodomir Mfura; Christine Moe

    2015-01-01

    There is a critical need for safe water in healthcare facilities (HCF) in low-income countries. HCF rely on water supplies that may require additional on-site treatment, and need sustainable technologies that can deliver sufficient quantities of water. Water treatment systems (WTS) that utilize ultrafiltration membranes for water treatment can be a useful technology in low-income countries, but studies have not systematically examined the feasibility of this technology in low-income settings...

  1. Denitrification mechanism in combustion of biocoal briquettes.

    Science.gov (United States)

    Kim, Heejoon; Li, Tianji

    2005-02-15

    Pulp black liquor (PBL), an industrial waste from paper production, has been previously shown to be an effective binder and denitrification agent for coal briquettes. This study investigated the denitrification mechanism of PBL in both the volatile combustion and char combustion stages of coal briquettes. X-ray diffraction and ion chromatography were used to analyze the residual ashes of combustion. The exhaust gas was analyzed by a flue gas analysis system and a Q-mass spectrometry system. The denitrification mechanism of PBL in the volatile combustion stage was found to result from the emission of NH3. The denitrification of PBL in the char combustion stage was associated with the NaOH contained in PBL. The direct reaction of NaOH with NO gas was examined, and some interesting phenomena were observed. Pure carbon or pure NaOH showed only limited reaction with NO. However, the mixture of NaOH and carbon (NaOH + C) significantly enhanced the reaction. This mixture increased the NO removal up to 100%. Subsequently, denitrification lasted for a long time period, with about 25% of NO removal. The pyrolysis characteristic of NaNO3, a compound resulting from denitrification, was also affected by the presence of carbon. In the presence of carbon, the NOx emission resulting from the pyrolysis of NaNO3 was reduced by a factor of 6. Since the denitrification phenomena appeared only in the absence of oxygen, a model of oxygen distribution in a burning coal briquette was employed to explain the reactions occurring in real combustion of coal briquettes.

  2. Dry low combustion system with means for eliminating combustion noise

    Science.gov (United States)

    Verdouw, Albert J.; Smith, Duane; McCormick, Keith; Razdan, Mohan K.

    2004-02-17

    A combustion system including a plurality of axially staged tubular premixers to control emissions and minimize combustion noise. The combustion system includes a radial inflow premixer that delivers the combustion mixture across a contoured dome into the combustion chamber. The axially staged premixers having a twist mixing apparatus to rotate the fluid flow and cause improved mixing without causing flow recirculation that could lead to pre-ignition or flashback.

  3. Sandia Combustion Research: Technical review

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1995-07-01

    This report contains reports from research programs conducted at the Sandia Combustion Research Facility. Research is presented under the following topics: laser based diagnostics; combustion chemistry; reacting flow; combustion in engines and commercial burners; coal combustion; and industrial processing. Individual projects were processed separately for entry onto the DOE databases.

  4. Residual hepatocellular carcinoma after oxaliplatin treatment has increased metastatic potential in a nude mouse model and is attenuated by Songyou Yin

    International Nuclear Information System (INIS)

    Xiong, Wei; Liu, Liang; Wang, Wen-Quan; Tang, Zhao-You; Ren, Zheng-Gang; Qiu, Shuang-Jian; Sun, Hui-Chuan; Wang, Lu; Liu, Bin-Bin; Li, Qi-Song; Zhang, Wei; Zhu, Xiao-Dong

    2010-01-01

    The opposite effects of chemotherapy, which enhance the malignancy of treated cancers such as hepatocellular carcinoma (HCC), are not well understood. We investigated this phenomenon and corresponding mechanisms to develop a novel approach for improving chemotherapy efficacy in HCC. Human hepatocellular carcinoma cell lines HepG2 (with low metastatic potential) and MHCC97L (with moderate metastatic potential) were used for the in vitro study. An orthotopic nude mouse model of human HCC was developed using MHCC97L cells. We then assessed the metastatic potential of surviving tumor cells after in vitro and in vivo oxaliplatin treatment. The molecular changes in surviving tumor cells were evaluated by western blot, immunofluorescence, and immunohistochemistry. The Chinese herbal extract Songyou Yin (composed of five herbs) was investigated in vivo to explore its effect on the metastatic potential of oxaliplatin-treated cancer cells. MHCC97L and HepG2 cells surviving oxaliplatin treatment showed enhanced migration and invasion in vitro. Residual HCC after in vivo oxaliplatin treatment demonstrated significantly increased metastasis to the lung (10/12 vs. 3/12) when re-inoculated into the livers of new recipient nude mice. Molecular changes consistent with epithelial-mesenchymal transition (EMT) were observed in oxaliplatin-treated tumor tissues and verified by in vitro experiments. The Chinese herbal extract Songyou Yin (4.2 and 8.4 g/kg) attenuated EMT and inhibited the enhanced metastatic potential of residual HCC in nude mice (6/15 vs. 13/15 and 3/15 vs. 13/15, respectively). The surviving HCC after oxaliplatin treatment underwent EMT and demonstrated increased metastatic potential. Attenuation of EMT by Songyou Yin may improve the efficacy of chemotherapy in HCC

  5. Use of Interface Treatment to Reduce Emissions from Residuals in Lower Permeability Zones to Groundwater flowing Through More Permeable Zones (Invited)

    Science.gov (United States)

    Johnson, P.; Cavanagh, B.; Clifton, L.; Daniels, E.; Dahlen, P.

    2013-12-01

    Many soil and groundwater remediation technologies rely on fluid flow for contaminant extraction or reactant delivery (e.g., soil vapor extraction, pump and treat, in situ chemical oxidation, air sparging, enhanced bioremediation). Given that most unconsolidated and consolidated settings have permeability contrasts, the outcome is often preferential treatment of more permeable zones and ineffective treatment of the lower permeability zones. When this happens, post-treatment contaminant emissions from low permeability zone residuals can cause unacceptable long-term impacts to groundwater in the transmissive zones. As complete remediation of the impacted lower permeability zones may not be practicable with conventional technologies, one might explore options that lead to reduction of the contaminant emissions to acceptable levels, rather than full remediation of the lower permeability layers. This could be accomplished either by creating a sustained emission reaction/attenuation zone at the high-low permeability interface, or by creating a clean soil zone extending sufficiently far into the lower permeability layer to cause the necessary reduction in contaminant concentration gradient and diffusive emission. These options are explored in proof-of-concept laboratory-scale physical model experiments. The physical models are prepared with two layers of contrasting permeability and either dissolved matrix storage or nonaqueous phase liquid (NAPL) in the lower permeability layer. A dissolved oxidant is then delivered to the interface via flow across the higher permeability layer and changes in contaminant emissions from the low permeability zone are monitored before, during, and after oxidant delivery. The use of three oxidants (dissolved oxygen, hydrogen peroxide and sodium persulfate) for treatment of emissions from petroleum hydrocarbon residuals is examined.

  6. cExternal beam radiation results in minimal changes in post void residual urine volumes during the treatment of clinically localized prostate cancer

    Directory of Open Access Journals (Sweden)

    Wallner Kent E

    2009-07-01

    Full Text Available Abstract Background To evaluate the impact of external beam radiation therapy (XRT on weekly ultrasound determined post-void residual (PVR urine volumes in patients with prostate cancer. Methods 125 patients received XRT for clinically localized prostate cancer. XRT was delivered to the prostate only (n = 66 or if the risk of lymph node involvement was greater than 10% to the whole pelvis followed by a prostate boost (n = 59. All patients were irradiated in the prone position in a custom hip-fix mobilization device with an empty bladder and rectum. PVR was obtained at baseline and weekly. Multiple clinical and treatment parameters were evaluated as predictors for weekly PVR changes. Results The mean patient age was 73.9 years with a mean pre-treatment prostate volume of 53.3 cc, a mean IPSS of 11.3 and a mean baseline PVR of 57.6 cc. During treatment, PVR decreased from baseline in both cohorts with the absolute difference within the limits of accuracy of the bladder scanner. Alpha-blockers did not predict for a lower PVR during treatment. There was no significant difference in mean PVR urine volumes or differences from baseline in either the prostate only or pelvic radiation groups (p = 0.664 and p = 0.458, respectively. Patients with a larger baseline PVR (>40 cc had a greater reduction in PVR, although the greatest reduction was seen between weeks one and three. Patients with a small PVR ( Conclusion Prostate XRT results in clinically insignificant changes in weekly PVR volumes, suggesting that radiation induced bladder irritation does not substantially influence bladder residual urine volumes.

  7. Indoor combustion and asthma.

    Science.gov (United States)

    Belanger, Kathleen; Triche, Elizabeth W

    2008-08-01

    Indoor combustion produces both gases (eg, nitrogen dioxide, carbon monoxide) and particulate matter that may affect the development or exacerbation of asthma. Sources in the home include both heating devices (eg, fireplaces, woodstoves, kerosene heaters, flued [ie, vented] or nonflued gas heaters) and gas stoves for cooking. This article highlights the recent literature examining associations between exposure to indoor combustion and asthma development and severity. Since asthma is a chronic condition affecting both children and adults, both age groups are included in this article. Overall, there is some evidence of an association between exposure to indoor combustion and asthma, particularly asthma symptoms in children. Some sources of combustion such as coal stoves have been more consistently associated with these outcomes than other sources such as woodstoves.

  8. Effect of post-polymerization heat-treatments on degree of conversion, leaching residual MMA and in vitro cytotoxicity of autopolymerizing acrylic repair resin.

    Science.gov (United States)

    Bural, Canan; Aktaş, Esin; Deniz, Günnur; Ünlüçerçi, Yeşim; Kızılcan, Nilgün; Bayraktar, Gülsen

    2011-11-01

    This study evaluated the effect of post-polymerization heat-treatments on degree of conversion (DC), residual methyl methacrylate concentration (MMA(r)) and in vitro cytotoxicity of autopolymerizing acrylic repair resin. A total of 336 specimens were prepared by bench- and hydroflask-curing and subjected to post-polymerization heat-treatments: a) water immersion at 60°C for 30 min, b) microwaving at 500 W for 3 min, c) combined use of water immersion and microwaving d) no treatment (as control). Specimens were eluted in cell culture medium for 1, 2, 5 and 7 days. DC and MMA(r) in eluates were measured by FTIR spectrometry and HPLC, respectively. In vitro cytotoxicity of eluates on L-929 fibroblasts was determined by XTT assay. Data were statistically analyzed with Dunn's multiple comparison and Pearson correlation tests (p≤0.05). DC was highest (99.9%) in bench- and hydroflask-cured groups which were subjected to water immersion. At all elution periods, MMA(r) was detected in eluates of all treatment groups and were higher in bench-cured groups than hydro-flask cured groups. Cell proliferation values indicated slightly cytotoxic effect throughout 7 days; regardless of the curing method or post-polymerization treatment. The correlation between MMA(r) and cell proliferation was negative after elution of 1, 2, 5 days and was only statistically significant (pMMA. Copyright © 2011 Academy of Dental Materials. Published by Elsevier Ltd. All rights reserved.

  9. [Residual states in 30 percent of adult patients with Bell's palsy. Early treatment with cortisone improves the healing process].

    Science.gov (United States)

    Berg, Thomas; Stjernquist-Desatnik, Anna; Kanerva, Mervi; Hultcrantz, Malou; Engström, Mats; Jonsson, Lars

    2015-01-06

    Bell's palsy is an acute unilateral weakness or paralysis of the face of unknown cause. The incidence of the disease is 30 individuals per 100,000 per year. It is a diagnosis of exclusion and other known causes for acute peripheral facial palsy must be ruled out. The prognosis is overall favorable and about 70% of the patients recover completely within 6 months without treatment. Recent randomized controlled Bell's palsy trials have shown that treatment with corticosteroids shortens time to recovery and improves recovery rates while antiviral treatment alone is not more effective than placebo. The combination of corticosteroids and antivirals has not been proven more effective than corticosteroids alone. We present an update of Bell's palsy in adults with focus on diagnosis, treatment and follow-up of these patients.

  10. Combustion irreversibilities: Numerical simulation and analysis

    Science.gov (United States)

    Silva, Valter; Rouboa, Abel

    2012-08-01

    An exergy analysis was performed considering the combustion of methane and agro-industrial residues produced in Portugal (forest residues and vines pruning). Regarding that the irreversibilities of a thermodynamic process are path dependent, the combustion process was considering as resulting from different hypothetical paths each one characterized by four main sub-processes: reactant mixing, fuel oxidation, internal thermal energy exchange (heat transfer), and product mixing. The exergetic efficiency was computed using a zero dimensional model developed by using a Visual Basic home code. It was concluded that the exergy losses were mainly due to the internal thermal energy exchange sub-process. The exergy losses from this sub-process are higher when the reactants are preheated up to the ignition temperature without previous fuel oxidation. On the other hand, the global exergy destruction can be minored increasing the pressure, the reactants temperature and the oxygen content on the oxidant stream. This methodology allows the identification of the phenomena and processes that have larger exergy losses, the understanding of why these losses occur and how the exergy changes with the parameters associated to each system which is crucial to implement the syngas combustion from biomass products as a competitive technology.

  11. Experimental investigation on the combustion characteristics of aluminum in air

    Science.gov (United States)

    Feng, Yunchao; Xia, Zhixun; Huang, Liya; Yan, Xiaoting

    2016-12-01

    With the aim of revealing the detailed process of aluminum combustion in air, this paper reports an experimental study on the combustion of aluminum droplets. In this work, the aluminum wires were exposed and heated by a CO2 laser to produce aluminum droplets, and then these droplets were ignited and burnt in air. The changing processes of aluminum wires, droplets and flames were directly recorded by a high-speed camera, which was equipped with a high magnification zoom lens. Meanwhile, the spectrum distribution of the flame was also registered by an optical spectrometer. Besides, burning residuals were collected and analyzed by the methods of Scanning Electron Microscopy (SEM) and Energy Dispersive Spectrometer (EDS). Experimental results show that, during combustion, the aluminum droplet is covered by a spherical vapor-phase flame, and the diameter of this flame is about 1.4 times of the droplet diameter, statistically. In the later stages of combustion, the molten aluminum and condensed oxide products can react to generate gaseous Al and Al2O spontaneously. Little holes are found on the surface of residuals, which are the transport channels of gaseous products, namely the gaseous Al and Al2O. The combustion residuals are consisted by lots of aluminum oxide particles with diameters less than 1 μm.

  12. Sandia Combustion Research Program

    Energy Technology Data Exchange (ETDEWEB)

    Johnston, S.C.; Palmer, R.E.; Montana, C.A. (eds.)

    1988-01-01

    During the late 1970s, in response to a national energy crisis, Sandia proposed to the US Department of Energy (DOE) a new, ambitious program in combustion research. Shortly thereafter, the Combustion Research Facility (CRF) was established at Sandia's Livermore location. Designated a ''user facility,'' the charter of the CRF was to develop and maintain special-purpose resources to support a nationwide initiative-involving US inventories, industry, and national laboratories--to improve our understanding and control of combustion. This report includes descriptions several research projects which have been simulated by working groups and involve the on-site participation of industry scientists. DOE's Industry Technology Fellowship program, supported through the Office of Energy Research, has been instrumental in the success of some of these joint efforts. The remainder of this report presents results of calendar year 1988, separated thematically into eleven categories. Referred journal articles appearing in print during 1988 and selected other publications are included at the end of Section 11. Our traditional'' research activities--combustion chemistry, reacting flows, diagnostics, engine and coal combustion--have been supplemented by a new effort aimed at understanding combustion-related issues in the management of toxic and hazardous materials.

  13. Extraction of toxic and valuable metals from wastewater sludge and ash arising from RECICLAGUA, a treatment plant for residual waters applying the leaching technique

    International Nuclear Information System (INIS)

    Guerrero D, J.J.

    2004-01-01

    Presently work, the technique is applied of having leached using coupled thermostatted columns, the X-ray diffraction for the identification of the atomic and molecular structure of the metals toxic that are present in the residual muds of a treatment plant of water located in the municipality of the Estado de Mexico, RECICLAGUA, likewise the techniques is used of Inductively Coupled Plasma Mass Spectroscopy and X-ray fluorescence analysis for the qualitative analysis. We took samples of residual sludge and incinerated ash of a treatment plant waste water from the industrial corridor Toluca-Lerma RECICLAGUA, located in Lerma, Estado de Mexico. For this study 100 g. of residual of sludge mixed with a solution to 10% of mineral acid or sodium hydroxide according to the case, to adjust the one p H at 2, 5, 7 and 10, bisulfite was added, of 0.3-1.5 g of dodecyl sulfate of sodium and 3.93 g of DTPA (triple V). Diethylene triamine penta acetate. These sludges and ashes were extracted from toxic and valuable metals by means of the leaching technique using coupled thermostated columns that which were designed by Dr. Jaime Vite Torres, it is necessary to make mention that so much the process as the apparatus with those that one worked was patented by him same. With the extraction of these metals, benefits are obtained, mainly of economic type, achieving the decrease of the volume of those wastes that have been generated; as well as the so much use of those residuals, once the metals have been eliminated, as of those residuals, once the metals have been eliminated, as of those liquors, the heavy metals were extracted. It was carried out a quantitative analysis using Icp mass spectroscopy, this way to be able to know the one content of the present metals in the samples before and after of leaching them, these results reported a great quantity of elements. Another of the techniques employees was the analysis by X-ray diffraction that provides an elementary content of the

  14. Residual risk

    African Journals Online (AJOL)

    ing the residual risk of transmission of HIV by blood transfusion. An epidemiological approach assumed that all HIV infections detected serologically in first-time donors were pre-existing or prevalent infections, and that all infections detected in repeat blood donors were new or incident infections. During 1986 - 1987,0,012%.

  15. Fluidized bed combustion and its application to refused fuels. Combustion en leche fluido y su aplicacion a combustibles residuales

    Energy Technology Data Exchange (ETDEWEB)

    Euba, J.

    1994-01-01

    As a consequence of the energetic crisis produced in th 70's it was proposed to find new power supplies and it also was the start of the use of traditional energy, which up to that date had not been profitable. At the same time, the worry about the pollutant emissions to the environment was increasing and finally it was approved a new legislation on atmosphere pollution, which is the Directive of the European community Council of 24th November 1988. Under these circumstances there are very important the new technologies for the supply of residual combustion with low values of pollution, where it is very important the combustion in fluidized bed. (Author)

  16. Combining physico-chemical analysis with a Daphnia magna bioassay to evaluate a recycling technology for drinking water treatment plant waste residuals.

    Science.gov (United States)

    Chen, Ting; Xu, Yongpeng; Zhu, Shijun; Cui, Fuyi

    2015-12-01

    Recycling water treatment plant (WTP) waste residuals is considered to be a feasible method to enhance the efficiency of pollutant removal. This study also evaluated the safety and water quality of a pilot-DWTP waste residuals recycling technology by combining physical-chemistry analysis with a Daphnia magna assay. The water samples taken from each treatment step were extracted and concentrated by XAD-2 resin and were then analyzed for immobilization and enzyme activity with D. magna. The measured parameters, such as the dissolve organic carbon (DOC), UV254 and THM formation potential (THMFPs) of the recycling process, did not obviously increase over 15 days of continuous operation and were even lower than typical values from a conventional process. The extract concentration ranged from 0 to 2 Leq/ml as measured on the 7th and 15th days and the immobilization of D. magna exposed to water treated by the recycling process was nearly equivalent to that of the conventional process. Both the superoxide dismutase (SOD) and the catalase (CAT) activity assay indicated that a lower dose of water extract (0.5, 1, 1.5 Leq/ml) could stimulate the enzyme activity of D. magna, whereas a higher dose (2 Leq/ml at the sampling point C3, R3, R4 ) inhibits the activity. Moreover, the SOD and CAT activity of D. magna with DOC and UV254 showed a strong concentration-effect relationship, where the concentration range of DOC and UV254 were 4.1-16.2 mg/L and 0.071-4.382 cm(-1), respectively. The results showed that there was no statistically significant difference (p>0.05) between the conventional and recycling treatment processes and the toxicity of water samples in the recycling process did not increase during the 15-day continuous recycling trial. Copyright © 2015 Elsevier Inc. All rights reserved.

  17. COMBUSTION PROPERTIES OF EUCALYPTUS WOOD

    Directory of Open Access Journals (Sweden)

    Yalçın ÖRS

    1999-03-01

    Full Text Available In this study, the combustion properties of some impregnation materials (abiotic and biotic factors used for eucalyptus wood in interior or exterior environments were investigated. The experimental samples were prepared from Eucalyptus wood based on ASTM-D-1413-76 Tanalith-CBC, boric acid, borax, vacsol-WR, immersol-WR, polyethylen glycole-400 and ammonium sulphate were used as an impregnation material. The results indicated that, vacuum treatment on Eucalyptus gave the lowest retention value of salts. Compounds containing boron+salt increased fire resistance however water repellents decreased the wood flammability.

  18. Memantine add-on to antipsychotic treatment for residual negative and cognitive symptoms of schizophrenia: a meta-analysis.

    Science.gov (United States)

    Kishi, Taro; Matsuda, Yuki; Iwata, Nakao

    2017-07-01

    We examined whether memantine add-on to antipsychotic treatment is beneficial in schizophrenia treatment. This systematic review and meta-analysis aimed to achieve stronger evidence on the efficacy and safety of memantine add-on for treating schizophrenia. We analyzed double-blind, randomized, placebo-controlled trials of memantine add-on treatment in schizophrenia patients receiving antipsychotics. The primary outcomes were amelioration of negative symptoms and all-cause discontinuation. Dichotomous outcomes are presented as risk ratios (RRs), and continuous outcomes are presented as mean differences (MDs) or standardized mean differences (SMDs). Eight studies (n = 448) were included. Although memantine add-on treatment was superior to placebo for ameliorating negative symptoms (SMD = -0.96, p = 0.006, I 2  = 88%; N = 7, n = 367) in the Positive and Negative Syndrome Scale general subscale (MD = -1.62, p = 0.002, I 2  = 0%; N = 4, n = 151) and Mini-Mental Status Examination score (MD = -3.07, p add-on treatment remained superior to placebo (SMD = -1.29, p = 0.00001). Meta-regression analysis showed that patient age was associated with memantine-associated amelioration of negative symptoms (slope = 0.171, p = 0.0206). Memantine add-on treatment may be beneficial for treating psychopathological symptoms (especially negative symptoms) in schizophrenia patients. The negative-symptom effect size may be associated with younger adult schizophrenia patients.

  19. Combustion synthesis of LiMn{sub 2}O{sub 4} with citric acid and the effect of post-heat treatment

    Energy Technology Data Exchange (ETDEWEB)

    Han, Y.S. [Korea Advanced Istitute of Science and Technology, Taejeon (Korea); Son, J.T. [Dong-A Electric Equipment Co. LTD., Seoul (Korea); Kim, H.G. [Korea Advanced Istitute of Science and Technology, Taejeon (Korea); Jung, H.T. [Dongshin University, Chonnam (Korea)

    2001-04-01

    Combustion process with citrate was used to produce the LiMn{sub 2}O{sub 4} powder. Precursors are pre-ignited in open air followed by post-heating in the range from 600 deg. C to 800 deg. C for 4 h. With varying the molar ration (R) of ethylene glycol (EG) to citric acid (CA) from 0 to 4, the effect of EG content on powder characteristics is evaluated. Vacuum drying promote the auto-ignition at room temperature. With small addition of EG metal ion was selectively segregated with organic substances and undesired lithium evaporation occurred during post-heating. LiMn {sub 2}O{sub 4} phase which is produced by combustion reaction was decomposed back to Mn {sub 3}O{sub 4} because the reaction temperature was higher than 950 deg. C. With increasing EG content, the homogeneity of LiMn {sub 2}O{sub 4} powder increased and specific surface area increased. And lithium evaporation during vacuum drying and/or ignition also increased. (author). 18 refs., 1 tab., 11 figs.

  20. Interaction of acid mine drainage with Ordinary Portland Cement blended solid residues generated from active treatment of acid mine drainage with coal fly ash.

    Science.gov (United States)

    Gitari, Wilson M; Petrik, Leslie F; Key, David L; Okujeni, Charles

    2011-01-01

    Fly ash (FA) has been investigated as a possible treatment agent for Acid mine drainage (AMD) and established to be an alternative, cheap and economically viable agent compared to the conventional alkaline agents. However, this treatment option also leads to generation of solid residues (SR) that require disposal and one of the proposed disposal method is a backfill in coal mine voids. In this study, the interaction of the SR with AMD that is likely to be present in such backfill scenario was simulated by draining columns packed with SR and SR + 6% Ordinary Portland Cement (OPC) unsaturated with simulated AMD over a 6 month period. The evolving geochemistry of the liquid/solid (L/S) system was evaluated in-terms of the mineral phases likely or controlling contaminants attenuation at the different pH regimes generated. Stepwise acidification of the percolates was observed as the drainage progressed. Two pH buffer zones were observed (7.5-9 and 3-4) for SR and (11.2-11.3 and 3.5-4) for SR + 6% OPC. The solid residue cores (SR) appeared to have a significant buffering capacity, maintaining a neutral to slightly alkaline pH in the leachates for an extended period of time (97 days: L/S 4.3) while SR + 6% OPC reduced this neutralization capacity to 22 days (L/S 1.9). Interaction of AMD with SR or SR + 6% OPC generated alkaline conditions that favored precipitation of Fe, Al, Mn-(oxy) hydroxides, Fe and Ca-Al hydroxysulphates that greatly contributed to the contaminants removal. However, precipitation of these phases was restricted to the pH of the leachates remaining at neutral to circum-neutral levels. Backfill of mine voids with SR promises to be a feasible technology for the disposal of the SR but its success will greatly depend on the disposal scenario, AMD generated and the alkalinity generating potential of the SR. A disadvantage would be the possible re-dissolution of the precipitated phases at pH water column. However extrapolation of this concept to a field

  1. Impact of microwave pre-treatment on the batch anaerobic digestion of two-phase olive mill solid residue: a kinetic approach

    International Nuclear Information System (INIS)

    Rincon, B.; Gonzalez de Canales, M.; Martin, A.; Borja, R.

    2016-01-01

    The effect of a microwave (MW) pre-treatment on two-phase olive mill solid residue (OMSR) or alperujo with a view to enhancing its anaerobic digestibility was studied. The MW pre-treatment was carried out at a power of 800 W and at a targeted temperature of 50 °C using different heating rates and holding times. The following specific energies were applied: 4377 kJ·kg TS−1 (MW1), 4830 kJ·kg TS−1 (MW2), 7170 kJ·kg TS−1 (MW3) and 7660 kJ·kg TS−1 (MW4). The maximum methane yield, 395±1 mL CH4·g VSadded−1, was obtained for MW4. The effect of the pre-treatment on the kinetics of the process was also studied. The methane production curves generated during the batch tests showed a first exponential stage and a second sigmoidal stage for all the cases studied. In the first stage, the kinetic constant for the pre-treatment MW1 was 54.8% higher than that obtained for untreated OMSR. [es

  2. Combustion Characterization of Individual Bio-oil Droplets

    DEFF Research Database (Denmark)

    Hansen, Brian Brun; Jensen, Peter Arendt

    2015-01-01

    Single droplet combustion characteristics has been investigated for bio-oil slurries, containing biomass residue, and compared to conventional fuels for pulverized burners, such as fuel oil (start up) and wood chips (solid biomass fuel). The investigated fuels ignition delays and pyrolysis behavior...

  3. Heavy metals behaviour during mono-combustion and co-combustion of sewage sludge

    Energy Technology Data Exchange (ETDEWEB)

    Lopes, M. Helena; Abelha, Pedro; Olieveira, J.F. Santos; Gulyurtlu, Ibrahim; Cabrita, Isabel [INETI-DEECA, Lisboa (Portugal)

    2005-03-01

    This paper presents the study of the combustion of granular dry sewage sludge performed on a pilot fluidized bed system. The results of mono-combustion of sludge and co-combustion with coal were compared with those of coal combustion for ash partitioning, the formation of gaseous pollutants and heavy metals behaviour. It was found that the mineral matter of sludge was essentially retained as bottom ashes. The production of fines ashes was small during the mono-combustion due to the tendency of coal to produce fine ashes which also contained unburned char. The degree of heavy metal volatilization was found to be slightly higher during co-combustion than in mono-combustion; however, most of them were retained in ashes and their emissions were found to be below the regulated levels. Hg was completely volatilized; however, during combustion trials involving coal it was captured by cyclone ashes at temperatures below 300 deg C. During sludge mono-combustion the retention of Hg in cyclone ashes containing low LOI was not enough to decrease emissions below the regulated levels; hence, it is necessary to install dedicated flue gas treatment for Hg removal. The leachability and ecotoxicity of sludge and ashes was compared with the new regulatory limits for landfill disposal in the EU. It was found that the release of organic matter and heavy metals found in the sludge was low from granular bed ashes; hence, except for sulphate release, bed ashes were converted into inert and non-ecotoxic materials. Ashes from test with limestone and cyclone ashes seemed to be more problematic because of pH effects and contamination with steel corrosion products. The recovery and reutilization of sludge bed ashes could, therefore, be possible, as long as the release of sulphate do not interfere with the process.

  4. Surgical treatment of residual osgood-schlatter disease in young adults: role of the mobile osseous fragment.

    Science.gov (United States)

    Nierenberg, Gabriel; Falah, Mazen; Keren, Yaniv; Eidelman, Mark

    2011-03-11

    Osgood-Schlatter disease is a well-known condition in late childhood characterized by pain over the tibial tubercle. This condition usually resolves spontaneously at skeletal maturity. Few patients develop pain over the tibial tubercle. Radiological examination demonstrates a round regular ossification over the tubercle. Treatment is usually symptomatic, but occasionally surgical treatment is necessary, usually due to the development of a painful ossicle. This article reports our experience with refractory Osgood-Schlatter disease in 22 patients. Most patients were operated under local anesthesia. A midline longitudinal skin incision was used, followed by subperiosteal dissection of the osseous fragment. The knee was put in soft dressing. Patients were encouraged to resume daily activity immediately postoperatively. No wound complications were noted. All patients returned to their previous level of physical activity within 12 weeks postoperatively. All but 1 were free of pain on kneeling or direct pressure over the knee joint. Based on our experience, we devised a treatment algorithm. We believe that the key factors for successful surgical treatment are clear visualization of separation on lateral knee radiographic view and a clinical mobility positive test (firm grasping of the prominent part of the tubercle and its sliding movement). Our results are uniformly good; the only failure related to mistaken inclusion criteria where the lateral radiograph did not show a distinctly separated fragment. Copyright 2011, SLACK Incorporated.

  5. Application of Fly Ash from Solid Fuel Combustion in Concrete

    DEFF Research Database (Denmark)

    Pedersen, Kim Hougaard

    2008-01-01

    Application of Fly Ash from Solid Fuel Combustion in Concrete Kim H. Pedersen Abstract Industrial utilization of fly ash from pulverized coal combustion plays an important role in environmentally clean and cost effective power generation. Today, the primary market for fly ash utilization...... is as pozzolanic additive in the production of concrete. However, the residual carbon in fly ash can adsorb the air entraining admixtures (AEAs) added to enhance air entrainment in concrete in order to increase its workability and resistance toward freezing and thawing conditions. The problem has increased...... with implementation of low-NOx combustion technologies. The present thesis concerns three areas of importance within this field: 1) testing of fly ash adsorption behavior; 2) the influence of fuel type and combustion conditions on the ash adsorption behaviour including full-scale experiments at the power plant...

  6. Creep Deformation, Rupture Analysis, Heat Treatment and Residual Stress Measurement of Monolithic and Welded Grade 91 Steel for Power Plant Components

    Science.gov (United States)

    Shrestha, Triratna

    Modified 9Cr-1 Mo (Grade 91) steel is currently considered as a candidate material for reactor pressure vessels (RPVs) and reactor internals for the Very High Temperature Reactor (VHTR), and in fossil-fuel fired power plants at higher temperatures and stresses. The tensile creep behavior of Grade 91 steel was studied in the temperature range of 600°C to 750°C and stresses between 35 MPa and 350 MPa. Heat treatment of Grade 91 steel was studied by normalizing and tempering the steel at various temperatures and times. Moreover, Thermo-Ca1c(TM) calculation was used to predict the precipitate stability and their evolution, and construct carbon isopleths of Grade 91 steel. Residual stress distribution across gas tungsten arc welds (GTAW) in Grade 91 steel was measured by the time-of-flight neutron diffraction using the Spectrometer for Materials Research at Temperature and Stress (SMARTS) diffractometer at Lujan Neutron Scattering Center, Los Alamos National Laboratory, Los Alamos, NM, USA. Analysis of creep results yielded stress exponents of ˜9-11 in the higher stress regime and ˜1 in the lower stress regime. The creep behavior of Grade 91 steel was described by the modified Bird-Mukherjee-Dorn relation. The rate-controlling creep deformation mechanism in the high stress regime was identified as the edge dislocation climb with a stress exponent of n = 5. On the other hand, the deformation mechanism in the Newtonian viscous creep regime (n = 1) was identified as the Nabarro-Herring creep. Creep rupture data were analyzed in terms of Monkman-Grant relation and Larson-Miller parameter. Creep damage tolerance factor and stress exponent were used to identify the cause of creep damage. The fracture surface morphology of the ruptured specimens was studied by scanning electron microscopy to elucidate the failure mechanisms. Fracture mechanism map for Grade 91 steel was developed based on the available material parameters and experimental observations. The microstructural

  7. Residual basins

    International Nuclear Information System (INIS)

    D'Elboux, C.V.; Paiva, I.B.

    1980-01-01

    Exploration for uranium carried out over a major portion of the Rio Grande do Sul Shield has revealed a number of small residual basins developed along glacially eroded channels of pre-Permian age. Mineralization of uranium occurs in two distinct sedimentary units. The lower unit consists of rhythmites overlain by a sequence of black shales, siltstones and coal seams, while the upper one is dominated by sandstones of probable fluvial origin. (Author) [pt

  8. Characterization of CTX-M enzymes, quinolone resistance determinants, and antimicrobial residues from hospital sewage, wastewater treatment plant, and river water.

    Science.gov (United States)

    Conte, Danieli; Palmeiro, Jussara Kasuko; da Silva Nogueira, Keite; de Lima, Thiago Marenda Rosa; Cardoso, Marco André; Pontarolo, Roberto; Degaut Pontes, Flávia Lada; Dalla-Costa, Libera Maria

    2017-02-01

    Multidrug-resistant (MDR) bacteria are widespread in hospitals and have been increasingly isolated from aquatic environments. The aim of the present study was to characterize extended-spectrum β-lactamase (ESBL) and quinolone-resistant Enterobacteriaceae from a hospital effluent, sanitary effluent, inflow sewage, aeration tank, and outflow sewage within a wastewater treatment plant (WWTP), as well as river water upstream and downstream (URW and DRW, respectively), of the point where the WWTP treated effluent was discharged. β-lactamase (bla) genes, plasmid-mediated quinolone resistance (PMQR), and quinolone resistance-determining regions (QRDRs) were assessed by amplification and sequencing in 55 ESBL-positive and/or quinolone-resistant isolates. Ciprofloxacin residue was evaluated by high performance liquid chromatography. ESBL-producing isolates were identified in both raw (n=29) and treated (n=26) water; they included Escherichia coli (32), Klebsiella pneumoniae (22) and Klebsiella oxytoca (1). Resistance to both cephalosporins and quinolone was observed in 34.4% of E. coli and 27.3% of K. pneumoniae. Resistance to carbapenems was found in 5.4% of K. pneumoniae and in K. oxytoca. Results indicate the presence of bla CTX-M (51/55, 92.7%) and bla SHV (8/55, 14.5%) ESBLs, and bla GES (2/55, 3.6%) carbapenemase-encoding resistance determinants. Genes conferring quinolone resistance were detected at all sites, except in the inflow sewage and aeration tanks. Quinolone resistance was primarily attributed to amino acid substitutions in the QRDR of GyrA (47%) or to the presence of PMQR (aac-(6')-Ib-cr, oqxAB, qnrS, and/or qnrB; 52.9%) determinants. Ciprofloxacin residue was absent only from URW. Our results have shown strains carrying ESBL genes, PMQR determinants, and mutations in the gyrA QRDR genes mainly in hospital effluent, URW, and DRW samples. Antimicrobial use, and the inefficient removal of MDR bacteria and antibiotic residue during sewage treatment, may

  9. Combustion of drops of Mexican fuel oils with high asphaltenes content; Combustion de gotas de combustoleos mexicanos con alto contenido de asfaltenos

    Energy Technology Data Exchange (ETDEWEB)

    Garcia Rodriguez, Jose Francisco [Instituto de Investigaciones Electricas, Cuernavaca (Mexico)

    1998-09-01

    In this work the combustion of fuel drops with a content of 18% of asphaltenes has been studied . The results obtained for this fuel were compared with the ones obtained for another with a content of 12% asphaltenes. The drops were suspended in a platinum filament and burned in an spherical radiant furnace. The drop size varied between 600 and 800 microns. The fuel drops with 12% asphaltenes showed shorter combustion times, a smaller diameter increment of the smaller diameter during the combustion stages and also a shorter burning time of the carbonaceous residue than the fuel drops with a content of 18% asphaltenes. [Espanol] En el presente trabajo se ha estudiado la combustion de gotas de combustible con 18% de contenido de asfaltenos. Los resultados obtenidos para este combustible se compararon con los obtenidos para otro con 12% de contenido de asfaltenos. Las gotas fueron suspendidas en un filamento de platino y quemadas en un horno radiante esferico. El tamano de las gotas vario entre 600 y 800 micras. Las gotas de combustible con 12% de asfaltenos mostraron tiempos de combustion mas cortos, un incremento del diametro menor durante las etapas de combustion y un tiempo de quemado del residuo carbonoso tambien mas corto que las gotas del combustible con 18% de contenido de asfaltenos.

  10. Technical and economic assessment of process of treatment of coated bituminous sludge by combustion/vitrification (report PNGMDR 2013-2015)

    International Nuclear Information System (INIS)

    2015-01-01

    This note reports the assessment of a processing by combustion/vitrification of about 60.000 parcels of coated bituminous sludge belonging to intermediate-level long-lived and low-level long-lived category, and warehoused on the Marcoule CEA site. This assessment identifies the front-end cost of an exploratory R and D which would be required to undo technological locks, the cost of design, realisation and exploitation of the associated installation, and the negative features dues to the lack of technological maturity and to the management of environmental risks and impacts in comparison with the reference industrial solution (geological storage). As a conclusion, the authors state that the process is still not technically feasible

  11. Additional correction of OAB symptoms by two anti-muscarinics for men over 50 years old with residual symptoms of moderate prostatic obstruction after treatment with Tamsulosin.

    Science.gov (United States)

    Kosilov, Kirill; Loparev, Sergey; Ivanovskaya, Marina; Kosilova, Liliya

    2015-03-01

    To study the effectiveness and safety of combined standard-dosed Solifenacin and Trospium for management of symptoms of overactive bladder (OAB) in elderly patients after the treatment with Tamsulosin. A total of 417 men over 50 years of age (average age 57.9 (8.3)) with diagnosed prostatic obstruction (score 8-19 according to I-PSS), who had not taken Tamsulosin before, were enrolled in the study. I-PSS questionnaire (from 8 to 19 - moderate) and Awareness Tool questionnaire for evaluating OAB symptoms (total score for OAB symptoms over 8) were used at the beginning and at the end of the observation. Also, urodynamic parameters were examined. Percentage of patients with prevalent symptoms of obstruction of urethra decreases after the treatment with Tamsulosin and then rises again (36.2%), but absolute number of patients remains smaller than initial data. Percentage of patients with relative prevalence of symptoms of overactive bladder slightly increases against administration of Tamsulosin and reaches initial values at the time of administration of anti-muscarinic drugs with absolute decrease in number of such patients. Combination of Trospium and Solifenacin is an effective way to manage residual symptoms of hyperactive bladder during treatment of early obstruction of urinary bladder.

  12. Combustion and regulation; Combustion et reglementation

    Energy Technology Data Exchange (ETDEWEB)

    NONE

    1997-12-31

    This conference was organized after the publication of the French by-law no 2010 relative to combustion installations and to the abatement of atmospheric pollution. Five topics were discussed during the conference: the new regulations, their content, innovations and modalities of application; the means of energy suppliers to face the new provisions and their schedule; the manufacturers proposals for existing installations and the new equipments; the administration control; and the impact of the new measures on exploitation and engineering. Twenty papers and 2 journal articles are reported in these proceedings. (J.S.)

  13. Short-term alendronate treatment does not maintain a residual effect on spinal fusion with interbody devices and bone graft after treatment withdrawal: an experimental study on spinal fusion in pigs.

    Science.gov (United States)

    Huang, Baoding; Zou, Xuenong; Li, Haisheng; Xue, Qingyun; Bünger, Cody

    2013-02-01

    Whether alendronate treatment has a residual effect on bone ingrowth into porous biomaterial in humans or experimental animals after treatment withdrawal is still unknown. The purpose of this study was to investigate bone ingrowth into porous tantalum and carbon fiber interbody implants after discontinuing alendronate treatment in experimental spinal fusion in pigs. Twenty-four pigs were randomly divided into two groups of each 12 pigs. The pigs underwent anterior intervertebral lumbar arthrodeses at L2-3, L4-5 and L6-7. Each level was randomly allocated to one of the three implants: a porous tantalum ring with pedicle screw fixation, a porous tantalum ring or a carbon fiber cage with anterior staple fixation. The central hole of implants was packed with an autograft. Alendronate was given orally for the first 3 months to one of the two groups. The pigs were observed for 6 months postoperatively. Histology and micro-CT scans were done at the endpoint. The spinal fusion rates of each implant showed no differences between two treatment groups. Furthermore, no differences were found between two groups as for bone ingrowth into the central holes of implants and bone-implant interface in each implant, or as for the pores of tantalum implants. Trabecular bone microarchitecture in the central hole of the carbon fiber cage did not differ between two treatment groups. The application of ALN, with a dose equivalent to that given to humans during the first 3 months after surgery, does not maintain a residual effect on spinal fusion with porous tantalum ring and autograft after treatment withdrawal in a porcine ALIF model.

  14. Fate and possible nutritional and toxicological significance of methylbromide residues in fumigated cocoa beans. Coordinated programme on isotopic tracer-aided studies on foreign chemical residues in food

    International Nuclear Information System (INIS)

    Adomako, D.

    1975-03-01

    Methyl bromide residues in cocoa as a result of fumigation under practical conditions have been studied. Cocoa beans were exposed to 14 C-labelled CH 3 Br for 24 hours at 20-32degC and dosage 23.5 to 28mg/1 of fumigants (moisture content of 6-7%). Whole unroasted beans and their shells and nibs as well as shells and nibs of roasted (105degC for 30 min) beans were extracted separately with toluene (for free CH 3 Br) and the dried residues wet combusted. 14 C-activities were determined by liquid scintillation counting. Total methyl bromide (bound and free) was equivalent 83-98ppm in whole unroasted beans 35 hours after treatment and aeration, and 31, 15 and 10ppm after 7, 42 and 70 days respectively in one set of experiments and 37, 53 and 42ppm after 76, 60 and 51 days in another set. Approximately 80% of the residue occurred in the shells which constitute only 12 to 13% of unroasted beans. 99% of the total residues appeared to be in chemically-bound form. Roasting reduced the total residues by 32 to 62% in nibs and 3.6 to 14% in shells. A striking effect of roasting was the occurrence in roasted nibs of residues as (extractable) carbon-14 (62-82% of the total residues compared to 16.5 - 27% in unroasted nibs). The bound residues behaved as methylated derivatives whilst the volatile fraction behaved as volatile aroma compounds formed by Maillard type reactions from the 14 C-labelled amino acides and sugars

  15. Determination of pharmaceutical residues and assessment of their removal efficiency at the Daugavgriva municipal wastewater treatment plant in Riga, Latvia.

    Science.gov (United States)

    Reinholds, I; Muter, O; Pugajeva, I; Rusko, J; Perkons, I; Bartkevics, V

    2017-01-01

    Pharmaceutical products (PPs) belong to emerging contaminants that may accumulate along with other chemical pollutants in wastewaters (WWs) entering industrial and/or urban wastewater treatment plants (WWTPs). In the present study, the technique of ultra-high-performance liquid chromatography coupled to Orbitrap high-resolution mass spectrometry (Orbitrap-HRMS) was applied for the analysis of 24 multi-class PPs in WW samples collected at different technological stages of Daugavgriva WWTP located in Riga, Latvia. Caffeine and acetaminophen levels in the range of 7,570-11,403 ng/L and 810-1,883 ng/L, respectively, were the predominant compounds among 19 PPs determined in the WW. The results indicate that aerobic digestion in biological ponds was insufficiently effective to degrade most of the PPs (reduction efficiency <0-50.0%) with the exception of four PPs that showed degradation efficiency varying from 55.0 to 99.9%. Tests of short-term chemical and enzymatic hydrolysis for PP degradation in WW samples were performed, and the results reflected the complexity of different degradation mechanisms and physicochemical transformations of PPs. The toxicological studies of WW impact on Daphnia magna indicated gradual reduction of the total toxicity through the treatment stages at the WWTP.

  16. A chemically enhanced biological process for lowering operative costs and solid residues of industrial recalcitrant wastewater treatment.

    Science.gov (United States)

    Di Iaconi, Claudio; Del Moro, Guido; De Sanctis, Marco; Rossetti, Simona

    2010-06-01

    An innovative process based on ozone-enhanced biological degradation, carried out in an aerobic granular biomass system (SBBGR--Sequencing Batch Biofilter Granular Reactor), was tested at pilot scale for tannery wastewater treatment chosen as representative of industrial recalcitrant wastewater. The results have shown that the process was able to meet the current discharge limits when the biologically treated wastewater was recirculated through an adjacent reactor where a specific ozone dose of 120 mg O3/L(influent) was used. The benefits produced by using ozone were appreciable even visually since the final effluent of the process looked like tap water. In comparison with the conventional treatment, the proposed process was able to reduce the sludge production by 25-30 times and to save 60% of operating costs. Molecular in situ detection methods were employed in combination with the traditional measurements (oxygen uptake rate, total protein content, extracellular polymeric substances and hydrophobicity) to evaluate microbial activity and composition, and the structure of the biomass. A stable presence of active bacterial populations was observed in the biomass with the simultaneous occurrence of distinctive functional microbial groups involved in carbon, nitrogen and sulphate removal under different reaction environments established within the large microbial aggregates. The structure and activity of the biomass were not affected by the use of ozone. 2010 Elsevier Ltd. All rights reserved.

  17. Enhanced primary treatment of concentrated black water and kitchen residues within DESAR concept using two types of anaerobic digesters.

    Science.gov (United States)

    Kujawa-Roeleveld, K; Elmitwalli, T; Zeeman, G

    2006-01-01

    Anaerobic digestion of concentrated domestic wastewater streams--black or brown water, and solid fraction of kitchen waste is considered as a core technology in a source separation based sanitation concept (DESAR--decentralised sanitation and reuse). A simple anaerobic digester can be implemented for an enhanced primary treatment or, in some situations, as a main treatment. Two reactor configurations were extensively studied; accumulation system (AC) and UASB septic tank at 15, 20 and 25 degrees C. Due to long retention times in an AC reactor, far stabilisation of treated medium can be accomplished with methanisation up to 60%. The AC systems are the most suitable to apply when the volume of waste to be treated is minimal and when a direct reuse of a treated medium in agriculture is possible. Digested effluent contains both liquid and solids. In a UASB septic tank, efficient separation of solids and liquid is accomplished. The total COD removal was above 80% at 25 degrees C. The effluent contains COD and nutrients, mainly in a soluble form. The frequency of excess sludge removal is low and sludge is well stabilised due to a long accumulation time.

  18. Internal combustion engine

    Science.gov (United States)

    Baker, Quentin A.; Mecredy, Henry E.; O'Neal, Glenn B.

    1991-01-01

    An improved engine is provided that more efficiently consumes difficult fuels such as coal slurries or powdered coal. The engine includes a precombustion chamber having a portion thereof formed by an ignition plug. The precombustion chamber is arranged so that when the piston is proximate the head, the precombustion chamber is sealed from the main cylinder or the main combustion chamber and when the piston is remote from the head, the precombustion chamber and main combustion chamber are in communication. The time for burning of fuel in the precombustion chamber can be regulated by the distance required to move the piston from the top dead center position to the position wherein the precombustion chamber and main combustion chamber are in communication.

  19. Transition nozzle combustion system

    Energy Technology Data Exchange (ETDEWEB)

    Kim, Won-Wook; McMahan, Kevin Weston; Maldonado, Jaime Javier

    2016-11-29

    The present application provides a combustion system for use with a cooling flow. The combustion system may include a head end, an aft end, a transition nozzle extending from the head end to the aft end, and an impingement sleeve surrounding the transition nozzle. The impingement sleeve may define a first cavity in communication with the head end for a first portion of the cooling flow and a second cavity in communication with the aft end for a second portion of the cooling flow. The transition nozzle may include a number of cooling holes thereon in communication with the second portion of the cooling flow.

  20. Studies in combustion dynamics

    Energy Technology Data Exchange (ETDEWEB)

    Koszykowski, M.L. [Sandia National Laboratories, Livermore, CA (United States)

    1993-12-01

    The goal of this program is to develop a fundamental understanding and a quantitative predictive capability in combustion modeling. A large part of the understanding of the chemistry of combustion processes comes from {open_quotes}chemical kinetic modeling.{close_quotes} However, successful modeling is not an isolated activity. It necessarily involves the integration of methods and results from several diverse disciplines and activities including theoretical chemistry, elementary reaction kinetics, fluid mechanics and computational science. Recently the authors have developed and utilized new tools for parallel processing to implement the first numerical model of a turbulent diffusion flame including a {open_quotes}full{close_quotes} chemical mechanism.

  1. Alcohol combustion chemistry

    KAUST Repository

    Sarathy, Mani

    2014-10-01

    Alternative transportation fuels, preferably from renewable sources, include alcohols with up to five or even more carbon atoms. They are considered promising because they can be derived from biological matter via established and new processes. In addition, many of their physical-chemical properties are compatible with the requirements of modern engines, which make them attractive either as replacements for fossil fuels or as fuel additives. Indeed, alcohol fuels have been used since the early years of automobile production, particularly in Brazil, where ethanol has a long history of use as an automobile fuel. Recently, increasing attention has been paid to the use of non-petroleum-based fuels made from biological sources, including alcohols (predominantly ethanol), as important liquid biofuels. Today, the ethanol fuel that is offered in the market is mainly made from sugar cane or corn. Its production as a first-generation biofuel, especially in North America, has been associated with publicly discussed drawbacks, such as reduction in the food supply, need for fertilization, extensive water usage, and other ecological concerns. More environmentally friendly processes are being considered to produce alcohols from inedible plants or plant parts on wasteland. While biofuel production and its use (especially ethanol and biodiesel) in internal combustion engines have been the focus of several recent reviews, a dedicated overview and summary of research on alcohol combustion chemistry is still lacking. Besides ethanol, many linear and branched members of the alcohol family, from methanol to hexanols, have been studied, with a particular emphasis on butanols. These fuels and their combustion properties, including their ignition, flame propagation, and extinction characteristics, their pyrolysis and oxidation reactions, and their potential to produce pollutant emissions have been intensively investigated in dedicated experiments on the laboratory and the engine scale

  2. Combuster. [low nitrogen oxide formation

    Science.gov (United States)

    Mckay, R. A. (Inventor)

    1978-01-01

    A combuster is provided for utilizing a combustible mixture containing fuel and air, to heat a load fluid such as water or air, in a manner that minimizes the formation of nitrogen oxide. The combustible mixture passes through a small diameter tube where the mixture is heated to its combustion temperature, while the load fluid flows past the outside of the tube to receive heat. The tube is of a diameter small enough that the combustible mixture cannot form a flame, and yet is not subject to wall quench, so that combustion occurs, but at a temperature less than under free flame conditions. Most of the heat required for heating the combustible mixture to its combustion temperature, is obtained from heat flow through the walls of the pipe to the mixture.

  3. Toxicology of Biodiesel Combustion products

    Science.gov (United States)

    1. Introduction The toxicology of combusted biodiesel is an emerging field. Much of the current knowledge about biological responses and health effects stems from studies of exposures to other fuel sources (typically petroleum diesel, gasoline, and wood) incompletely combusted. ...

  4. Novel approaches in advanced combustion characterization of fuels for advanced pressurized combustion

    Energy Technology Data Exchange (ETDEWEB)

    Aho, M.; Haemaelaeinen, J. [VTT Energy (Finland); Joutsenoja, T. [Tampere Univ. of Technology (Finland)

    1996-12-01

    This project is a part of the EU Joule 2 (extension) programme. The objective of the research of Technical Research Centre of Finland (VTT) is to produce experimental results of the effects of pressure and other important parameters on the combustion of pulverized coals and their char derivates. The results can be utilized in modelling of pressurized combustion and in planning pilot-scale reactors. The coals to be studied are Polish hvb coal, French lignite (Gardanne), German anthracite (Niederberg) and German (Goettelbom) hvb coal. The samples are combusted in an electrically heated, pressurized entrained flow reactor (PEFR), where the experimental conditions are controlled with a high precision. The particle size of the fuel can vary between 100 and 300 {mu}m. The studied things are combustion rates, temperatures and sizes of burning single coal and char particles. The latter measurements are performed with a method developed by Tampere University of Technology, Finland. In some of the experiments, mass loss and elemental composition of the char residue are studied in more details as the function of time to find out the combustion mechanism. Combustion rate of pulverized (140-180 {mu}m) Gardanne lignite and Niederberg anthracite were measured and compared with the data obtained earlier with Polish hvb coal at various pressures, gas temperatures, oxygen partial pressures and partial pressures of carbon dioxide in the second working period. In addition, particle temperatures were measured with anthracite. The experimental results were treated with multivariable partial least squares (PLS) method to find regression equation between the measured things and the experimental variables. (author)

  5. Reduction in pesticide residue levels in olives by ozonated and tap water treatments and their transfer into olive oil.

    Science.gov (United States)

    Kırış, Sevilay; Velioglu, Yakup Sedat

    2016-01-01

    The effects of different wash times (2 and 5 min) with tap and ozonated water on the removal of nine pesticides from olives and the transfer ratios of these pesticides during olive oil production were determined. The reliability of the analytical methods was also tested. The applied methods of analysis were found to be suitable based on linearity, trueness, repeatability, selectivity and limit of quantification all the pesticides tested. All tap and ozonated water wash cycles removed a significant quantity of the pesticides from the olives, with a few exceptions. Generally, extending the wash time increased the pesticide reduction with ozonated water, but did not make significant differences with tap water. During olive oil processing, depending on the processing technique and physicochemical properties of the pesticides, eight of nine pesticides were concentrated into olive oil (processing factor > 1) with almost no significant difference between treatments. Imidacloprid did not pass into olive oil. Ozonated water wash for 5 min reduced chlorpyrifos, β-cyfluthrin, α-cypermethrin and imidacloprid contents by 38%, 50%, 55% and 61% respectively in olives.

  6. Methods for storage and disposal of residues from wastewater treatment of former uranium mining and milling facilities in Germany

    International Nuclear Information System (INIS)

    Larue, J.; Weiss, D.; Kiessig, G.

    2002-01-01

    In connection with the flooding of uranium mines in Saxony and Thuringia, there are contaminated pit waters that must be purified before discharge into surface waters. The expected duration of the water purification process until concentrations of natural radionuclides, various heavy metals and arsenic are low enough to allow direct discharge into surface waters amounts to decades . To prevent or minimize the leaching of the contaminants from the sludge of the water treatment in the long term, the contaminants are either transformed into chemical compounds of low solubility or affixed within ion exchange resins. Due to the accumulation of those contaminants during the water processing procedure, the residua must be disposed of for reasons of radiation protection and waste management. A final storage of the residua in accord with nuclear regulatory stipulations is unnecessary because of the contamination levels and also because of the mining origin. The method of residua-storage chosen to be best suited to a particular site has to be based on costs-to-benefit analyses, giving due consideration to the different aspects e.g. radiation and environmental protection, long term safety, form of immobilization, site specific conditions. These methods will be described and illustrated using specific examples of applications. (author)

  7. Characterization of Rio Blanco retort 1 water following treatment by lime-soda softening and reverse osmosis; Residual brine treated by wet-air oxidation

    Energy Technology Data Exchange (ETDEWEB)

    Kocornik, D.; Renk, R.

    1986-09-01

    Laboratory research has been conducted to evaluate the chemical, physical, and toxicological characteristics of treated and untreated water pumped from the flooded modified in situ retort at lease tract C-a. This wastewater had a total dissolved solids (TDS) content of about 5450 mg/L and a total organic carbon content of about 16 mg/L. Wet chemical analyses, metals analyses, particle-size analyses, and MICROTOX assays were performed on the wastewater before and after treatment by lime-soda softening and reverse osmosis. The reverse osmosis membrane used in this research was a Filmtec model SW30-2521 spiral-wound polyamide unit. In a short duration test at a TDS of 21,800 mg/L, the reverse osmosis system successfully removed dissolved solids and organics from the wastewater. The water was also much less toxic to the MICROTOX organism after treatment by reverse osmosis. Membrane fouling was observed when water with a TDS of 54,500 mg/L was treated. Treatment of the reverse osmosis residual brine was attempted by subcritical wet-air oxidation. The brine remaining after the 170-hour test on the water with a TDS of 5450 mg/L was subjected to temperatures ranging from 204/sup 0/C (400/sup 0/F) to 315/sup 0/C (600/sup 0/F) and pressures from 500 to 1600 psig for approximately 30 minutes. The waste treated by the higher temperatures and pressures showed good removals of organics, nitrogen compounds, and some metals. The sample treated at 302/sup 0/C (575/sup 0/F) and 1300 psi was assayed for MICROTOX response and no toxicity was measured. The reverse osmosis brine was significantly toxic to the MICROTOX organism before treatment by subcritical wet-air oxidation. 14 refs., 8 figs., 14 tabs.

  8. Combustion Engine Identification and Control

    OpenAIRE

    Blasco Serrano, Daniel

    2013-01-01

    The topic of this thesis is system identification and control of two different internal combustion engines, Partially Premixed Combustion (PPC) engine and a more conventional Combustion Ignited (CI) diesel engine. The control of both engines is aimed to emission reduction and to increase the eficiency. There is an introduction to the internal combustion engine, as well as theory used about system identification and Model Predictive Control (MPC). A physical model of a PPC en...

  9. Minimum incidence of congenital talipes equino-varus (CTEV) and post treatment evaluation of residual deformities in a population in Zimbabwe.

    Science.gov (United States)

    Madzivire, D; Useh, D; Mashegede, P T; Siziya, S

    2002-01-01

    To determine the minimum incidence (MI) of congenital talipes equino-varus (CTEV) in children; evaluate the association between CTEV and other congenital anomalies, and to assess the presence of residual deformities after conservative management at the physiotherapy department of Harare Central Hospital (HCH), Zimbabwe. A three year retrospective study. Physiotherapy Department, HCH, Harare, Zimbabwe. Eighty-two children with CTEV who were assessed and treated at HCH Physiotherapy Department from January 1994 to December 1996. MI of club foot and degree of correction of the club foot after conservative management of the deformity by the physiotherapist. An MI rate of about 0.9 per 1000 was found over a three year period. It was also found that 30.5% of these children had other associated congenital abnormalities. There was no significant association between gender and severity of deformity (P = 0.326). A significant association between the severity of CTEV and the presence of other associated congenital deformities was found (P = 0.013). 91% of the feet were found to have a satisfactory result of treatment using the Wynne Davis scoring system (WDSS). 52% of the patients with residual deformity after discharge from physiotherapy presented with limitation in ankle and sub-talar movements. This study also indicated that children with grade 2 type of deformities were more likely to have other congenital abnormalities than those with grades 1 or 3. The MI of CTEV in the studied population was found to be lower than other countries. The WDSS indicated that a great majority of the feet examined scored above average score.

  10. Effects of oral hygiene, residual caries and cervical Marginal-gaps on the survival of proximal atraumatic restorative treatment approach restorations

    Directory of Open Access Journals (Sweden)

    Arthur M Kemoli

    2011-01-01

    Full Text Available Background: Although Atraumatic restorative treatment (ART approach has been in existence for a while, the reasons for the poor performance of multisurface ART restorations are not very clear. Aim: The aim of this study is to investigate the effects of oral hygiene, residual caries and cervical marginal-gaps on survival of proximal ART restorations. Settings: Two rural divisions in Kenya were selected for the study. Design: A randomized clinical trial. Material and Methods: The 804 children in the study had their baseline- and 2-year dental plaque levels documented. Each child received one proximal restoration in a primary molar using ART approach, together with trained and pre-tested operators/assistants, three glass ionomer cements (GIC-brands and two tooth-isolation methods. The restorations were clinically evaluated soon after placement and after 2 years. Post-restorative bite-wing radiographs taken soon after restoration were also evaluated. Statistical analysis: Statistical Package for Social Sciences (SPSS version 14 computer programme was used and results tested using Pearson′s correlation, Cox Proportional Hazards regression analysis and Multiple Logistic regression models tests. Results: At baseline and after 2 years, the mean cumulative survival and plaque index changed from 94.4% to 30.8% and 2.34 (Standard Deviation, or SD of 0.46 to 1.92 (SD 2.1 respectively, with higher plaque indices associated with higher restoration failures. Of the 507 radiographs evaluated, 48 (9.5%, 63 (12.4% and 9 (1.8% restorations had residual caries (RC, cervical marginal-gaps (CMG and both RC/CMG respectively. Survival of the restorations with RC/CMG was significantly lower (p = 0.003 compared to those with RC or without RC. Conclusion: Low survival of proximal restorations in the study was associated with the presence of cervical marginal-gaps.

  11. Life cycle assessment of post-consumer plastics production from waste electrical and electronic equipment (WEEE) treatment residues in a Central European plastics recycling plant.

    Science.gov (United States)

    Wäger, Patrick A; Hischier, Roland

    2015-10-01

    Plastics play an increasingly important role in reaching the recovery and recycling rates defined in the European WEEE Directive. In a recent study we have determined the life cycle environmental impacts of post-consumer plastics production from mixed, plastics-rich WEEE treatment residues in the Central European plant of a market-leading plastics recycler, both from the perspective of the customers delivering the residues and the customers buying the obtained post-consumer recycled plastics. The results of our life cycle assessments, which were extensively tested with sensitivity analyses, show that from both perspectives plastics recycling is clearly superior to the alternatives consid